Sample records for jackpile sandstone bed

  1. Hydrology and water-quality monitoring considerations, Jackpile uranium mine, northwestern New Mexico

    USGS Publications Warehouse

    Zehner, H.H.

    1985-01-01

    The Jackpile Uranium Mine, which is on the Pueblo of Laguna in northwestern New Mexico, was operated from 1953 to 1980. The mine and facilities have affected 3,141 acres of land, and about 2,656 acres were yet to be reclaimed by late 1980. The intended use of the restored land is stock grazing. Fractured Dakota Sandstone and Mancos Shale of Cretaceous age overlie the Jackpile sandstone and a 200-ft-thick tight mudstone unit of the Brushy Basin Member underlies the Jackpile. The hydraulic conductivity of the Jackpile sandstone probably is about 0.3 ft/day. The small storage coefficients determined from three aquifer tests indicate that the Jackpile sandstone is a confined hydrologic system throughout much of the mine area. Sediment from the Rio Paguate has nearly filled the Paguate Reservoir near Laguna since its construction in 1940. The mean concentrations of uranium, Ra-226, and other trace elements generally were less than permissible limits established in national drinking water regulations or New Mexico State groundwater regulations. No individual surface water samples collected upstream from the mine contained concentrations of Ra-226 in excess of the permissible limits. Ra-226 concentrations in many individual samples collected from the Rio Paguate from near the mouth of the Rio Moquino to the sampling sites along the downstream reach of the Rio Paguate, however, exceeded the recommended permissible concentration of Ra-226 for public drinking water supplies. Concentrations in surface water apparently are changed by groundwater inflow near the confluence of the two streams. The altitude of the water tables in the backfill of the pits will be controlled partly by the water level in the Rio Paguate. Other factors controlling the altitudes of the water tables are the recharge rate to the backfill and the hydraulic conductivities of the backfill, alluvium, Jackpile sandstone, and mudstone unit of the Brushy Basin Member. After reclamation, most of the shallow

  2. Uranium mobility and accumulation along the Rio Paguate, Jackpile Mine in Laguna Pueblo, NM.

    PubMed

    Blake, Johanna M; De Vore, Cherie L; Avasarala, Sumant; Ali, Abdul-Mehdi; Roldan, Claudia; Bowers, Fenton; Spilde, Michael N; Artyushkova, Kateryna; Kirk, Matthew F; Peterson, Eric; Rodriguez-Freire, Lucia; Cerrato, José M

    2017-04-19

    The mobility and accumulation of uranium (U) along the Rio Paguate, adjacent to the Jackpile Mine, in Laguna Pueblo, New Mexico was investigated using aqueous chemistry, electron microprobe, X-ray diffraction and spectroscopy analyses. Given that it is not common to identify elevated concentrations of U in surface water sources, the Rio Paguate is a unique site that concerns the Laguna Pueblo community. This study aims to better understand the solid chemistry of abandoned mine waste sediments from the Jackpile Mine and identify key hydrogeological and geochemical processes that affect the fate of U along the Rio Paguate. Solid analyses using X-ray fluorescence determined that sediments located in the Jackpile Mine contain ranges of 320 to 9200 mg kg -1 U. The presence of coffinite, a U(iv)-bearing mineral, was identified by X-ray diffraction analyses in abandoned mine waste solids exposed to several decades of weathering and oxidation. The dissolution of these U-bearing minerals from abandoned mine wastes could contribute to U mobility during rain events. The U concentration in surface waters sampled closest to mine wastes are highest during the southwestern monsoon season. Samples collected from September 2014 to August 2016 showed higher U concentrations in surface water adjacent to the Jackpile Mine (35.3 to 772 μg L -1 ) compared with those at a wetland 4.5 kilometers downstream of the mine (5.77 to 110 μg L -1 ). Sediments co-located in the stream bed and bank along the reach between the mine and wetland had low U concentrations (range 1-5 mg kg -1 ) compared to concentrations in wetland sediments with higher organic matter (14-15%) and U concentrations (2-21 mg kg -1 ). Approximately 10% of the total U in wetland sediments was amenable to complexation with 1 mM sodium bicarbonate in batch experiments; a decrease of U concentration in solution was observed over time in these experiments likely due to re-association with sediments in the reactor. The findings

  3. A Toxic Legacy: Stories of Jackpile Mine

    ERIC Educational Resources Information Center

    Jacobs, Connie A.

    2004-01-01

    Leslie Marmon Silko physically locates the climax of the novel, Ceremony at Canoncito, southeast of the Jackpile Uranium Mine, and so metaphorically correlates this site with witchery. The novel is ultimately the story of Tayo, and how he must restore harmony between the land and his people.

  4. Cross-bedding Related Anisotropy and its Role in the Orientation of Joints in an Aeolian Sandstone

    NASA Astrophysics Data System (ADS)

    Deng, S.; Cilona, A.; Mapeli, C.; Panfilau, A.; Aydin, A.; Prasad, M.

    2014-12-01

    Previous research revealed that the cross-bedding related anisotropy in aeolian sandstones affects the orientation of compaction bands, also known as anticracks. We hypothesize that cross-bedding should a have similar influence on the orientation of the joints within the same rock at the same location. To test this hypothesis, we investigated the relationship between the cross-beds and the cross-bed package confined joints in the Jurassic aeolian Aztec Sandstone cropping out in the Valley of Fire State Park, Nevada. The field data demonstrates that the cross-bed package confined joints occur at high-angle to bedding and trend roughly parallel to the dip direction of the cross-beds. This shows that the cross-bed orientation and the associated anisotropy also exert a strong control on the formation and orientation of the joints. In order to characterize the anisotropy due to cross-bedding in the Aztec Sandstone, we measured the P-wave velocities parallel and perpendicular to bedding from 11 samples in the laboratory using a bench-top ultrasonic assembly. The measured P-wave anisotropy is about 13% on average. Based on these results, a numerical model based on the generalized Hooke's law for anisotropic materials is analyzed assuming the cross-bedded sandstone to be transversely isotropic. Using this model, we tested various cross-bed orientations as well as different strain boundary conditions (uniaxial, axisymmetric and triaxial). It is possible to define a boundary condition under which the modeled results roughly match with the observed relationship between cross-bed package confined joints and cross-beds. These results have important implications for fluid flow through aeolian sandstones in reservoirs and aquifers.

  5. Supercritical CO2 Migration under Cross-Bedded Structures: Outcrop Analog from the Jurassic Navajo Sandstone

    NASA Astrophysics Data System (ADS)

    Lee, S.; Allen, J.; Han, W.; Lu, C.; McPherson, B. J.

    2011-12-01

    Jurassic aeolian sandstones (e.g. Navajo and White Rim Sandstones) on the Colorado Plateau of Utah have been considered potential sinks for geologic CO2 sequestration due to their regional lateral continuity, thickness, high porosity and permeability, presence of seal strata and proximity to large point sources of anthropogenic CO2. However, aeolian deposits usually exhibit inherent internal complexities induced by migrating bedforms of different sizes and their resulting bounding surfaces. Therefore, CO2 plume migration in such complex media should be well defined and successively linked in models for better characterization of the plume behavior. Based on an outcrop analog of the upper Navajo Sandstone in the western flank of the San Rafael Swell, Utah, we identified five different bedform types with dune and interdune facies to represent the spatial continuity of lithofacies units. Using generated 3D geometrical facies patterns of cross-bedded structures in the Navajo Sandstone, we performed numerical simulations to understand the detailed behavior of CO2 plume migration under the different cross-bedded bedforms. Our numerical simulation results indicate that cross-bedded structures (bedform types) play an important role on governing the rate and directionality of CO2 migration, resulting in changes of imbibition processes of CO2. CO2 migration tends to follow wind ripple laminations and reactivation surfaces updip. Our results suggest that geologically-based upscaling of CO2 migration is crucial in cross-bedded formations as part of reservoir or basin scale models. Furthermore, comparative modeling studies between 3D models and 2D cross-sections extracted from 3D models showed the significant three-dimensional interplay in a cross-bedded structure and the need to correctly capture the geologic heterogeneity to predict realistic CO2 plume behavior. Our outcrop analog approach presented in this study also demonstrates an alternative method for assessing geologic

  6. Cross-bedding related anisotropy and its interplay with various boundary conditions in the formation and orientation of joints in an aeolian sandstone

    NASA Astrophysics Data System (ADS)

    Deng, Shang; Cilona, Antonino; Morrow, Carolyn; Mapeli, Cesar; Liu, Chun; Lockner, David; Prasad, Manika; Aydin, Atilla

    2015-08-01

    Previous research revealed that the cross-bedding related anisotropy in Jurassic aeolian Aztec Sandstone cropping out in the Valley of Fire State Park, Nevada, affects the orientation of compaction bands, also known as anti-cracks or closing mode structures. We hypothesize that cross-bedding should have a similar influence on the orientation of the opening mode joints within the same rock at the same location. To test this hypothesis, we investigated the relationship between the orientation of cross-beds and the orientation of different categories of joint sets including cross-bed package confined joints and joint zones in the Aztec Sandstone. The field data show that the cross-bed package confined joints occur at high-angle to bedding and trend roughly parallel to the dip direction of the cross-beds. In comparison, the roughly N-S trending joint zones appear not to be influenced by the cross-beds in any significant way but frequently truncate against the dune boundaries. To characterize the anisotropy due to cross-bedding in the Aztec Sandstone, we measured the P-wave velocities parallel and perpendicular to bedding from 11 samples and determined an average P-wave anisotropy to be slightly larger than 13%. From these results, a model based on the generalized Hooke's law for anisotropic materials is used to analyze deformation of cross-bedded sandstone as a transversely isotropic material. In the analysis, the dip angle of cross-beds is assumed to be constant and the strike orientation varying from 0° to 359° in the east (x), north (y), and up (z) coordinate system. We find qualitative agreement between most of the model results and the observed field relations between cross-beds and the corresponding joint sets. The results also suggest that uniaxial extension (εzz > εxx = εyy = 0) and axisymmetric extension (εxx = εyy < εzz and εxx = εyy > εzz) would amplify the influence of cross-bedding associated anisotropy on the joint orientation whereas a

  7. Energy monitoring and analysis during deformation of bedded-sandstone: use of acoustic emission.

    PubMed

    Wasantha, P L P; Ranjith, P G; Shao, S S

    2014-01-01

    This paper investigates the mechanical behaviour and energy releasing characteristics of bedded-sandstone with bedding layers in different orientations, under uniaxial compression. Cylindrical sandstone specimens (54 mm diameter and 108 mm height) with bedding layers inclined at angles of 10°, 20°, 35°, 55°, and 83° to the minor principal stress direction, were produced to perform a series of Uniaxial Compressive Strength (UCS) tests. One of the two identical sample sets was fully-saturated with water before testing and the other set was tested under dry conditions. An acoustic emission system was employed in all the testing to monitor the acoustic energy release during the whole deformation process of specimens. From the test results, the critical joint orientation was observed as 55° for both dry and saturated samples and the peak-strength losses due to water were 15.56%, 20.06%, 13.5%, 13.2%, and 13.52% for the bedding orientations 10°, 20°, 35°, 55°, and 83°, respectively. The failure mechanisms for the specimens with bedding layers in 10°, 20° orientations showed splitting type failure, while the specimens with bedding layers in 55°, 83° orientations were failed by sliding along a weaker bedding layer. The failure mechanism for the specimens with bedding layers in 35° orientation showed a mixed failure mode of both splitting and sliding types. Analysis of the acoustic energy, captured from the acoustic emission detection system, revealed that the acoustic energy release is considerably higher in dry specimens than that of the saturated specimens at any bedding orientation. In addition, higher energy release was observed for specimens with bedding layers oriented in shallow angles (which were undergoing splitting type failures), whereas specimens with steeply oriented bedding layers (which were undergoing sliding type failures) showed a comparatively less energy release under both dry and saturated conditions. Moreover, a considerable amount of

  8. Quasi-planer-laminated sandstone beds of the Lower Cretaceous Bootlegger Member, north-central Montana: Evidence of combined-flow sedimentation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Arnott, R.W.C.

    1993-05-01

    Lower-shoreface to shallow-shelf strata of the Bootlegger Member of the Lower Cretaceous Blackleaf Formation are characterized by interbedded sandstone and mudstone. Sandstone beds are characterized by a peculiar planar lamination showing a subtle although perceptible undulation; spacing-to-height ratios of the undulation are generally 100 or more. Typically the undulation shows no evidence of lateral accretion but only vertical aggradation, and as a result most beds consist of a single laminaset. Aspects of quasi-planar-laminated beds indicate single-event storm sedimentation, and paleocurrent data indicate offshore sediment transport. By its sedimentary characteristics and its similarity with a bed configuration generated in an experimentalmore » wave duct, quasi-planar lamination is produced by high-energy combined flows. This style of stratification should be common in the shallow-marine stratigraphic record, and its recognition should aid in interpreting high-energy, combined-flow depositional events.« less

  9. Sandstone dykes in siwalik sandstone-sedimentology and basin analysis-subansiri district (NEFA), Eastern Himalaya

    NASA Astrophysics Data System (ADS)

    Kumar, Surendar; Singh, Trilochan

    1982-11-01

    Sandstone dykes (including sills) of varied thickness and with tapering ends are present either transecting or (sills) parallel to bedding in the Siwalik sandstone of Arunachal Pradesh (NEFA), Eastern Himalaya. The different sedimentary and microstructural analyses show varied conditions of deposition with changing facies from fluvial channel, to alluvial fan, to coastal plain-fan delta. The non-marine and shallow marine environments are indicated by the presence of organised and disorganised gradation and the presence of sandstone dykes in the interface regions. The orientations of the longer axes of the conglomerate along with the sand bedding indicate palaeoflow.

  10. Dakota sandstone facies, western Oklahoma panhandle

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Atalik, E.; Mansfield, C.F.

    The Cretaceous Dakota Sandstone in Cimarron County comprised three sandstone units and intervening mudrocks; it overlies the Kiowa Shale Member of the Purgatoire Formation. Deposits include shoreface, beach (foreshore) and dune, estuarine and tidal channel, marine marginal bay and swamp/marsh in a generally progradational sequences associated with marine regression in the Western Interior. The shoreface sand, characterized by ripple lamination, bioturbation and the trace fossils Teichichnus and Thalassinoides, is fine-grained, 5-10 m (15-30 ft) thick and grades into the underlying Kiowa Shale. Beach and associated dune deposits are 2-5 m (6-16 ft) thick, medium to fine-grained, medium to thick-bedded, tabular-planarmore » cross-bedded, and lenticular; cross-bed paleocurrent headings are northeasterly and northwesterly. Estuarine channel deposits are 3-5 m (10 to 16 ft) thick, trough to tabular-planar cross-bedded, and medium to coarse-grained with local conglomerate overlying the scoured base which commonly cuts into the Kiowa Shale or overlying shoreface sandstone; rip-up clasts and wood pieces are common but trace fossils are rare; southeasterly and southwesterly paleocurrents predominate. Tidal channel deposits are thinner (up to 2 m of 6 ft) and finer grained (medium to fine-grained) that the estuarine channel deposits; they occur within fine-grained sandstone and mudrock sequences, are trough cross-bedded, and commonly contain trace fossils (e.g., Skolithos) and wood fragments. Marine marginal (tidal flat or bay.) deposits comprise fine-grained sandstone, siltstone and interbedded shale, that are 1-3m (3-10 ft) thick with abundant burrows, small ripple marks, and parallel lamination. These grade into the fine to very fine-grained sandstones, siltstones, shales, and coals of the swamp/marsh deposits that are 1-5m (3-16 ft) thick and contain ripple marks, burrows, other trace fossils, and parallel lamination.« less

  11. Geology of deep-water sandstones in the Mississippi Stanley Shale at Cossatot Falls, Arkansas

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Coleman, J.L. Jr.

    1993-09-01

    The Mississippian Stanley Shale crops out along the Cossatot River in the Ouachita Mountains of western Arkansas. Here, exposures of deep-water sandstones and shales, on recently established public lands, present a rare, three-dimensional look at sandstones of the usually obscured Stanley. Cossatot Falls, within the Cossatot River State Park Natural Area, is a series of class IV and V rapids developed on massive- to medium-bedded quartz sandstones on the northern flank of an asymmetric, thrust-faulted anticline. In western Arkansas, the Stanley Shale is a 10,000-ft (3200-m) succession of deep-water sandstone and shale. At Cossatot Falls, approximately 50 ft (155 m)more » of submarine-fan-channel sedimentary rocks are exposed during low-river stages. This section is composed primarily of sets of thinning-upward sandstone beds. With rare exceptions, the sandstones are turbidites, grading from massive, homogeneous, basal beds upward through festoon-cross-bedded thick beds, into rippled medium and thin beds. Sandstone sets are capped by thin shales and siltstones. Regional, north-northwestward paleocurrent indicators are substantiated by abundant, generally east-west ripple crests asymmetric to the north-northwest. Flute casts at the top of the sandstone sequence indicate an additional east-ward flow component. Based on regional, lithologic characteristics, the sandstones at Cossatot Falls appear to be within the Moyers Formation. The Moyers is the upper sandstone unit of the Stanley and is an oil and gas reservoir in the eastern Oklahoma Ouachita Mountains.« less

  12. Stress-dependent permeability evolution in sandstones with anisotropic physical properties

    NASA Astrophysics Data System (ADS)

    Metz, V.; David, C.; Louis, L.; Rodriguez Rey, A.; Ruiz de Argandona, V. G.

    2003-04-01

    Fluid flow in reservoir rocks is strongly dependent on stress path and rock microstructure which may present a significant anisotropy. We present recent experimental data on the evolution of permeability with applied stress for three sandstones tested under triaxial conditions in the low confining pressure range (<10 MPa). Samples with diameter 40 mm and length 80 mm were cored in three orthogonal directions in blocks retrieved from quarries. One coring direction was perpendicular to the bedding plane whereas the other directions were arbitrarily chosen within the bedding plane. The selected rocks are the Bentheim sandstone (BNT), a quartz-rich cretaceous sandstone from Germany with 24% porosity, and two different varieties of a same jurassic formation in Northern Spain, the La Marina sandstone. The Yellow La Marina sandstone (YLM) with porosity 28% has a low cohesion and is the weathered form of the well-consolidated Grey La Marina sandstone (GLM) with porosity 17%. When loaded up to the failure stress, the more porous sandstones (BNT, YLM) exhibited a monotonic decrease of permeability even when the rock was dilating at deviatoric stresses close to the failure stress. On the other hand the permeability of the less porous sandstone (GLM) increased during the dilating phase. These results are in agreement with previous studies. In addition we observed that all three sandstones are anisotropic with respect to several physical properties including permeability. We systematically found a lower permeability in the direction perpendicular to the bedding plane, but the ratio of "vertical" to "horizontal" permeability varies from one sandstone to the other. The permeability anisotropy is compared to the anisotropy of electrical conductivity, acoustic velocity, capillary imbibition and elastic moduli: in general good correlations are found for all the properties. For the Bentheim sandstone, a microstructural study on thin sections revealed that the rock anisotropy is due

  13. Origin of the Nubian and similar sandstones

    USGS Publications Warehouse

    McKee, E.D.

    1963-01-01

    The Nubian Sandstone and similar sandstone bodies exposed across much of northern Africa and adjoining parts of Asia are characteristically formed of clean sand that is conspicuously cross stratified throughout. Such sandstone, here called Nubian-type sandstone, ranges from Cambrian through Cretaceous in age and its genesis has been interpreted in many ways. Studies of its primary structures, and of the direction of sand transport, based on statistical measurements of foreset dip directions, have contributed new data on its genesis. By far the most common structure in Nubian-type sandstone is a medium-scale planar-type cross stratification in which sets of evenly dipping cross beds are bounded by essentially flat-lying top and bottom surfaces to form tabular bodies. Other less numerous but typical structures are large-scale, truncated-wedge cross strata, trough-type cross strata, intraformational recumbent folds, small-scale ripple laminae, and dipping sets of tabular-planar cross beds. An analysis of these structures suggests that in the typical Nubian Sandstone of Cretaceous age eolian deposits are not represented and normal marine types probably also are lacking; flood plain, pond or lagoon, and other continental and marginal environments are indicated. In the Carboniferous rocks of Sinai Peninsula some beach sandstone and possibly some eolian, in addition to the types described, form part of the sequence. Direction of sand transport, as determined from cross-bed dips, was northerly in the Cretaceous Nubian of Libya, Sudan, and Egypt; easterly in the Jurassic Adigrat of Ethiopia; westerly in the Carboniferous of Sinai; northwesterly in the early Paleozoic of Jordan. ?? 1963 Ferdinand Enke Verlag Stuttgart.

  14. Lithostratigraphic controls on bedding-plane fractures and the potential for discrete groundwater flow through a siliciclastic sandstone aquifer, southern Wisconsin

    NASA Astrophysics Data System (ADS)

    Swanson, Susan K.

    2007-04-01

    Outcrop-analog studies of the Upper Cambrian Tunnel City Group sandstones in southern Wisconsin show the utility of lithostratigraphic information in hydrostratigraphic studies of siliciclastic sandstone aquifers. Recent work supports the lateral continuity of discrete groundwater flow through these sandstones. Lithologic description of the Reno Member of the Lone Rock Formation (Tunnel City Group) in outcrop and core reveals repeating sequences of three dominant lithofacies, including flat-pebble intraclast conglomerate with a glauconite-rich matrix; glauconitic and feldspathic subquartzose sandstone with horizontal-planar, low-angle, and hummocky lamination; and feldspathic subquartzose sandstone with dolomite-filled burrows. The vertically stacked Reno Member sequences have been interpreted as having a storm-related origin, and they are laterally continuous on the scale of an outcrop. Horizontal fracture locations correlate with bedding planes at contacts between lithofacies. They are most commonly associated with the base of the flat-pebble intraclast conglomerate or with partings along laminae and erosional surfaces in the laminated subquartzose sandstone lithofacies. Sequences show upward increases in natural gamma radiation due to increasing potassium feldspar content. The incorporation of the detailed lithostratigraphic information allows a more accurate interpretation of borehole natural gamma logs where the rocks are buried and saturated and clarifies the role of sedimentary structures in the distribution of features that might promote discrete flow through these rocks.

  15. Burial, thermal, and petroleum generation history of the Upper Cretaceous Steele Member of the Cody Shale (Shannon Sandstone Bed Horizon), Powder River Basin, Wyoming (Chapter A). Bulletin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Nuccio, V.F.

    The purposes of the study are to (1) present burial histories representative of the northwestern and southwestern parts of the Powder River Basin (south of lat 45 N.), (2) show the maximum level of thermal maturity for the Steele Member and its Shannon Sandstone Bed, and (3) show the source-rock potential and timing of petroleum generation for the Steele. It is hoped that data presented in the study will also lead to a better understanding of the burial and temperature history of the Shannon Sandstone Bed, an understanding crucial for diagenetic studies, fluid-flow modeling, and reservoir-rock characterization.

  16. Depositional environment of downdip Yegua (Eocene) sandstones, Jackson County, Texas

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Whitten, C.J.; Berg, R.R.

    Yegua sandstones at a depth of 8300-8580 ft (2530-2615 m) were partly cored in the Arco Jansky 1 dry hole. Total thickness of the sandstone section is approximately 240 ft (73 m). The sandstones are enclosed in thick marine shales and are about 20 mi (32 km) downdip from thicker and more abundant sandstones in the Yegua Formation. The section is similar to reservoirs recently discovered in the area at the Toro Grande (1984), Lost Bridge (1984), and El Torito (1985) fields. The sandstones are fine to very fine grained and occur in thin beds that are 0.5-9 ft (0.15-2.7more » m) thick. Sedimentary structures within the beds range from a lower massive division to a laminated or rippled upper division. Grain size within beds fines upward from 0.18 mm at the base to 0.05 mm at the top. The sandstones are interpreted to be turbidites of the AB type that were deposited within channels. The sandstones contain an average of 50% quartz and are classified as volcanic-arenites to feldspathic litharenites. Carbonate cement ranges from 0 to 27%. Average porosity is 29% and permeabilities are in the range of 60-1600 md in the clean sandstones. Much of the porosity is secondary and is the result of the dissolution of cements, volcanic rock fragments, and feldspar grains. Yegua sandstones produce gas and condensate at nearby Toro Grande field on a gentle, faulted anticline. The local trend of reservoir sandstones may be controlled in part by faulting that was contemporaneous with deposition.« less

  17. Nugget-Navaho-Aztec sandstone: interaction of eolian sand sea with Andean-type volcanic arc

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Marzolf, J.E.

    1986-05-01

    The Nugget-Navaho-Aztec sand sea was deposited east of an Andean-type volcanic arc. During the early stage of eolian deposition, fluvially transported sand was concentrated in the marine littoral zone and returned inland by onshore winds from the northwest. With progressive development of the arc, the sea withdrew. Wind direction changed from northwest to northeast. Previously deposited eolian sand was transported southwestward into the volcanic arc. Proximity of the arc can be detected with great difficulty by examining eolian and underlying red-bed facies. In southern Nevada, the volcanic arc is undetectable in eolian facies, but thin sandstone beds containing volcanic clastsmore » or weathered feldspar in the finer grained red-bed facies indicate arc volcanism; volcanic clasts are distinct in a basal conglomerate. Westward into California, the sub-Aztec Sandstone contains volcanic pebbles. The upper part of the Aztec Sandstone contains a 1 to 2-m thick volcaniclastic siltstone. Farther west, the Aztec Sandstone is interbedded with volcanic flows, ash flows, and flow breccias. These rocks might easily be mistaken for red beds in well cores or cuttings. Sand in sets of large-scale cross-beds remain virtually identical in composition and texture to sand in eolian facies of the Colorado Plateau. Where sets of eolian cross-beds lie on volcanics, the quartzose sandstone contains pebble to cobble-size volcanic clasts. Locally, cross-bed sets of yellowish-white, quartzose sandstone alternate with purplish-gray cross-bed sets containing numerous pebble to cobble-size volcanic clasts. The ability to recognize volcanic indicators within Nugget-Navaho-Aztec eolian facies is important in delineating the western margin of the back-arc eolian basin.« less

  18. Lattice strain measurements on sandstones under load using neutron diffraction

    NASA Astrophysics Data System (ADS)

    Frischbutter, A.; Neov, D.; Scheffzük, Ch.; Vrána, M.; Walther, K.

    2000-11-01

    Neutron diffraction methods (both time-of-flight- and angle-dispersive diffraction) are applied to intracrystalline strain measurements on geological samples undergoing uniaxial increasing compressional load. The experiments were carried out on Cretaceous sandstones from the Elbezone (East Germany), consisting of >95% quartz which are bedded but without crystallographic preferred orientation of quartz. From the stress-strain relation the Young's modulus for our quartz sample was determined to be (72.2±2.9) GPa using results of the neutron time-of-flight method. The influence of different kinds of bedding in sandstones (laminated and convolute bedding) could be determined. We observed differences of factor 2 (convolute bedding) and 3 (laminated bedding) for the elastic stiffness, determined with angle dispersive neutron diffraction (crystallographic strain) and with strain gauges (mechanical strain). The data indicate which geological conditions may influence the stress-strain behaviour of geological materials. The influence of bedding on the stress-strain behaviour of a laminated bedded sandstone was indicated by direct residual stress measurements using neutron time-of-flight diffraction. The measurements were carried out six days after unloading the sample. Residual strain was measured for three positions from the centre to the periphery and within two radial directions of the cylinder. We observed that residual strain changes from extension to compression in a different manner for two perpendicular directions of the bedding plane.

  19. Quartz cement in sandstones: a review

    NASA Astrophysics Data System (ADS)

    McBride, Earle F.

    Quartz cement as syntaxial overgrowths is one of the two most abundant cements in sandstones. The main factors that control the amount of quartz cement in sandstones are: framework composition; residence time in the "silica mobility window"; and fluid composition, flow volume and pathways. Thus, the type of sedimentary basin in which a sand was deposited strongly controls the cementation process. Sandstones of rift basins (arkoses) and collision-margin basins (litharenites) generally have only a few percent quartz cement; quartzarenites and other quartzose sandstones of intracratonic, foreland and passive-margin basins have the most quartz cement. Clay and other mineral coatings on detrital quartz grains and entrapment of hydrocarbons in pores retard or prevent cementation by quartz, whereas extremely permeable sands that serve as major fluid conduits tend to sequester the greatest amounts of quartz cement. In rapidly subsiding basins, like the Gulf Coast and North Sea basins, most quartz cement is precipitated by cooling, ascending formation water at burial depths of several kilometers where temperatures range from 60° to 100° C. Cementation proceeds over millions of years, often under changing fluid compositions and temperatures. Sandstones with more than 10% imported quartz cement pose special problems of fluid flux and silica transport. If silica is transported entirely as H 4SiO 4, convective recycling of formation water seems to be essential to explain the volume of cement present in most sandstones. Precipitation from single-cycle, upward-migrating formation water is adequate to provide the volume of cement only if significant volumes of silica are transported in unidentified complexes. Modeling suggests that quartz cementation of sandstones in intracratonic basins is effected by advecting meteoric water, although independent petrographic, isotopic or fluid inclusion data are lacking. Silica for quartz cement comes from both shale and sandstone beds within

  20. Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

    USGS Publications Warehouse

    Robinson, J.W.; McCabea, P.J.

    1997-01-01

    Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

  1. Fluvial sandstone reservoirs of Travis Peak (Hosston) Formation, east Texas basin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tye, R.S.

    1989-03-01

    Gas production (7.2 billion ft/sup 3/) from low-permeability sandstones in the Travis Peak Formation, North Appleby field, Nacogdoches County, Texas, is enhanced through massive hydraulic fracturing of stacked sandstones that occur at depths between 8000 and 10,000 ft. stratigraphic reservoirs were formed in multilateral tabular sandstones owing to impermeable mudstone interbeds that encase blocky to upward-fining sandstones. Pervasive quartz cement in the sandstones decreases porosity and permeability and augments the reservoir seal. Subsurface data indicate that much of this 2000-ft thick section represents aggradation of alluvial-valley deposits. Multiple channel belts form a network of overlapping, broad, tabular sandstones having thickness-to-widthmore » ratios of 1:850 (8-44 ft thick; widths exceed 4-5 mi). Six to eight channel belts, each containing 80-90% medium to fine-grained sandstone, can occupy a 200-ft thick interval. In a vertical sequence through one channel belt sandstone, basal planar cross-bedding grades upward into thinly interbedded sets of planar cross-beds and ripple cross-lamination. Clay-clast conglomerates line scoured channel bases. Adjacent to the channels, interbedded mudstones accumulated in well-drained swamps and lakes. Poorly sorted sandstones represent overbank deposition (crevasse splays and lacustrine deltas). During Travis Peak deposition, fluvial styles evolved from dominantly braided systems near the base of the formation to more mud-rich, meandering systems at the top.« less

  2. Reservoir characterization of Mesaverde (Campanian) bedload fluvial meanderbelt sandstones, northwestern Colorado

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jones, J.R. Jr.

    1984-04-01

    Reservoir characterization of Mesaverde meanderbelt sandstones is used to determined directional continuity of permeable zones. A 500-m (1600 ft) wide fluvial meanderbelt in the Mesaverde Group is exposed as laterally continuous 3-10-m (10-33-ft) high sandstone cliffs north of Rangely, Colorado. Forty-eight detailed measured sections through 3 point bar complexes oriented at right angles to the long axis of deposition and 1 complex oriented parallel to deposition were prepared. Sections were tied together by detailed sketches delineating and tracing major bounding surfaces such as scours and clay drapes. These complexes contain 3 to 8 multilateral sandstone packages separated by 5-20 cmmore » (2-8 in.) interbedded siltstone and shale beds. Component facies are point bars, crevasse splays, chute bars, and floodplain/overbank deposits. Two types of lateral accretion surfaces are recognized in the point bar facies. Gently dipping lateral accretions containing fining-upward sandstone packages. Large scale trough cross-bedding at the base grades upward into ripples and plane beds. Steeply dipping lateral accretion surfaces enclose beds characterized by climbing ripple cross laminations. Bounding surfaces draped by shale lags can seal vertically stacked point bars from reservoir communication. Scoured boundaries allow communication in some stacked point bars. Crevasse splays showing climbing ripples form tongues of very fine-grained sandstone which flank point bars. Chute channels commonly cut upper point bar surfaces at their downstream end. Chute facies are upward-fining with small scale troughs and common dewatering structures. Siltstones and shales underlie the point bar complexes and completely encase the meanderbelt system. Bounding surfaces at the base of the complexes are erosional and contain large shale rip-up clasts.« less

  3. Coastal dune facies, Permian Cutler Formation (White Rim Sandstone), Capitol Reef National Park area, southern Utah

    NASA Astrophysics Data System (ADS)

    Kamola, Diane L.; Chan, Marjorie A.

    1988-04-01

    The Permian Cutler Formation (White Rim Sandstone) in the Capitol Reef National Park area in southern Utah is an excellent example of a coastal dune complex subjected to periodic flooding by marine waters. Wind-ripple, grainfall and grainflow laminae compose the cross-sets deposited by eolian dunes. However, wave-reworked structures such as oscillation ripples, the occurrence of the characteristically marine trace fossils Thalassinoides and Chondrites, and interfingering marine carbonate beds of the Kaibab Formation collectively indicate marine interaction with the eolian environment. Four facies are distinguished: cross-stratified sandstone, burrowed to bioturbated sandstone, brecciated and deformed sandstone, and ripple-laminated sandstone and thin carbonate beds. One unusual aspect of the cross-stratified sandstone facies is the abundance of coarse-grained sand. Coarse-grained sand is atypical in many ancient eolian slipface deposits, but occurs here in large slipface foresets as both grainflow and wind-ripple deposits. No water-laid structures are found in these slipface deposits. Coarse-grained sand was probably transported to the Cutler shoreline by fluvial systems draining the Uncompahgre Uplift to the east, and then concentrated as coarse-grained ripples in interdune areas. Some of these coarse-grained ripples migrated up the stoss side of the dunes and accumulations of coarse-grained sand avalanched down the crest to form grainflow deposits. An extensive amount of soft-sediment deformation is indicated by the presence of convolute bedding and brecciation. These features occur near the zone of interfingering with marine carbonate beds of the Kaibab Formation. The water-saturated and moist conditions required for extensive deformation may have been controlled by the proximity of these sandstones to the shoreline, and fluctuations in the associated groundwater table.

  4. Development of Discrete Compaction Bands in Two Porous Sandstones

    NASA Astrophysics Data System (ADS)

    Tembe, S.; Baud, P.; Wong, T.

    2003-12-01

    Compaction band formation has been documented by recent field and laboratory studies as a localized failure mode occurring in porous sandstones. The coupling of compaction and localization may significantly alter the stress field and strain partitioning, and act as barriers within reservoirs. Two end-members of this failure mode that develop subperpendicular to the maximum principal stress have been identified: numerous discrete compaction bands with a thickness of only several grains, or a few diffuse bands that are significantly thicker. Much of what is known about discrete compaction bands derives from laboratory experiments performed on the relatively homogeneous Bentheim sandstone with 23% porosity. In this study we observe similar compaction localization behavior in the Diemelstadt sandstone, that has an initial porosity of 24.4% and a modal composition of 68% quartz, 26% feldspar, 4% oxides, and 2% micas. CT scans of the Diemelstadt sandstone indicate bedding corresponding to low porosity laminae. Saturated samples cored perpendicular to bedding were deformed at room temperature under drained conditions at a constant pore pressure of 10 MPa and a confining pressure range of 20-175 MPa. Acoustic emission activity and pore volume change were recorded continuously. Samples were deformed to axial strains of 1-4% and recovered from the triaxial cell for microstructural analysis. The mechanical data map the transition in failure mode from brittle faulting to compactive cataclastic flow. The brittle regime occurred at effective pressures up to 40 MPa, associated with failure by conjugate shear bands. At an effective pressure range of 60-175 MPa strain hardening and shear-enhanced compaction were accompanied by the development of discrete compaction bands, that was manifested by episodic surges of acoustic emission. Preliminary microstructural observations of the failed samples suggest that bedding influenced the band orientations which varies between 75-90\\deg

  5. Factors controlling localization of uranium deposits in the Dakota Sandstone, Gallup and Ambrosia Lake mining districts, McKinley County, New Mexico

    USGS Publications Warehouse

    Pierson, Charles Thomas; Green, Morris W.

    1977-01-01

    Geologic studies were made at all of the uranium mines and prospects in the Dakota Sandstone of Early(?) and Late Cretaceous age in the Gallup mining district, McKinley County, New Mexico. Dakota mines in the adjacent Ambrosia Lake mining district were visited briefly for comparative purposes. Mines in the eastern part of the Gallup district, and in the Ambrosia Lake district, are on the Chaco slope of the southern San Juan Basin in strata which dip gently northward toward the central part of the basin. Mines in the western part of the Gallup district are along the Gallup hogback (Nutria monocline) in strata which dip steeply westward into the Gallup sag. Geologic factors which controlled formation of the uranium deposits in the Dakota Sandstone are: (1) a source of uranium, believed to be uranium deposits of the underlying Morrison Formation of Late Jurassic age; (2) the accessibility to the Dakota of uranium-bearing solutions from the Morrison; (3) the presence in the Dakota of permeable sandstone beds overlain by impermeable carbonaceous shale beds; and (4) the occurrence within the permeable Dakota sandstone beds of carbonaceous reducing material as bedding-plane laminae, or as pockets of carbonaceous trash. Most of the Dakota uranium deposits are found in the lower part of the formation in marginal-marine distributary-channel sandstones which were deposited in the backshore environment. However, the Hogback no. 4 (Hyde) Mine (Gallup district) occurs in sandy paludal shale of the backshore environment, and another deposit, the Silver Spur (Ambrosia Lake district), is found in what is interpreted to be a massive beach or barrier-bar sandstone of the foreshore environment in the upper part of the Dakota. The sedimentary depositional environment most favorable for the accumulation of uranium is that of backshore areas lateral to main distributary channels, where levee, splay, and some distributary-channel sandstones intertongue with gray carbonaceous shales and

  6. The role of sandstone in the development of an Ozark karst system, south-central Missouri

    USGS Publications Warehouse

    Orndorff, R.C.; Weary, D.J.; Harrison, R.W.

    2006-01-01

    Cave, spring, and sinkhole development in the Ozarks of south-central Missouri is placed in a geologic framework through detailed geologic mapping. Geologic mapping shows that initial dissolution and inception of cave development is concentrated just beneath sandstone beds within Upper Cambrian and Lower Ordovician dolostone. Although rocks of the Ozarks have systematic and pervasive vertical joints, the development of karst conduits is controlled by bedding planes and stratigraphic variability. In the Salem Plateau of south-central Missouri, sinkholes occur in the lower part of the Ordovician Roubidoux Formation, where sinkholes are rimmed with and contain sandstone that has collapsed into voids in the underlying Ordovician Gasconade Dolomite. Cave diving by the Ozark Cave Diving Alliance into Alley Spring, a large (average flow 3.7 m3/s) spring along the Jacks Fork in the Ozark National Scenic Riverways, shows that although the spring discharges from the middle part of the Gasconade, the source of water is a cave passage just beneath the Gunter Sandstone Member of the Gasconade Dolomite. Artesian conditions cause the upward movement of groundwater from cavernous dolostone beneath the sandstone aquitards to the large springs. We hypothesize that sandstone, which is largely impermeable due to silica cementation, acts as a confining unit where hydraulic pressure, combined with mixing of water of differing chemistry, increases dissolution in the underlying dolostone beds. ?? 2006 Geological Society of America.

  7. Characterizing flow pathways in a sandstone aquifer at multiple depths

    NASA Astrophysics Data System (ADS)

    Medici, Giacomo; West, Jared; Mountney, Nigel

    2017-04-01

    Sandstone aquifers are commonly assumed to represent porous media characterized by a permeable matrix. However, such aquifers may be heavily fractured where rock properties and timing of deformation favour brittle failure and crack opening. In many aquifer types, fractures associated with faults, bedding planes and stratabound joints represent preferential pathways for fluids and contaminants. This presentation reports well-test results and outcrop-scale studies that reveal how strongly lithified siliciclastic rocks may be entirely dominated by fracture flow at shallow depths (≤ 150 m), similar to limestone and crystalline aquifers. The Triassic St Bees Sandstone Formation of the UK East Irish Sea Basin represents an optimum succession for study of the influence of both sedimentary and tectonic aquifer heterogeneities in a strongly lithified sandstone aquifer-type. This sedimentary succession of fluvial origin accumulated in rapidly subsiding basins, which typically favour preservation of complete depositional cycles, including fine-grained mudstone and silty sandstone layers of floodplain origin interbedded with sandstone-dominated fluvial channel deposits. Vertical joints in the St Bees Sandstone Formation form a pervasive stratabound system whereby joints terminate at bedding-parallel discontinuities. Additionally, normal faults are present through the succession and record development of open-fractures in their damage zones. Here, the shallow aquifer (depth ≤150 m BGL) was characterized in outcrop and well tests. Fluid temperature, conductivity and flow-velocity logs record inflows and outflows from normal faults, as well as from pervasive bed-parallel fractures. Quantitative flow logging analyses in boreholes that cut fault planes indicate that zones of fault-related open fractures typically represent ˜ 50% of well transmissivity. The remaining flow component is dominated by bed-parallel fractures. However, such sub-horizontal fractures become the

  8. Desert and groundwater dynamics of the Jurassic Navajo Sandstone, southeast Utah

    NASA Astrophysics Data System (ADS)

    Chan, M. A.; Hasiotis, S. T.; Parrish, J. T.

    2017-12-01

    The Jurassic Navajo Sandstone of southeastern Utah is a rich archive of a desert complex with an active groundwater system, influenced by climate changes and recharge from the Uncompahgre Uplift of the Ancestral Rocky Mountains. This eastern erg margin was dominated by dune deposits of large (>10 m thick) and small (m-scale) crossbedded sandstone sets. Within these porous deposits, common soft sediment deformation is expressed as contorted and upturned bedding, fluid escape structures, concentrations of clastic pipes with ring faults, and thick intervals of massive sandstone embedded in crossbedded sandstone. Collectively, these deformation features reflect changes and/or overpressure in the groundwater system. Interdune deposits record laterally variable bounding surfaces, resulting from the change in position of and proximity to the water table. Interdune modification by pedogenesis from burrows, roots, and trees suggest stable periods of moisture and water supply, as well as periodic drying expressed as polygonal cracked mud- to sand-cracked layers. Freshwater bedded and platy limestone beds represent lakes of decameter to kilometer extent, common in the upper part of the formation. Some carbonate springs that fed the lakes are preserved as limestone buildups (tufa mounds) with microbial structures. Extradunal deposits of rivers to small ephemeral streams show channelized and lenticular, subhorizontal, cm- to m-scale sandstone bodies with basal scours and rip-up clasts. Proxy records of the active hydrology imply a changing landscape at the Navajo desert's edge, punctuated by periods of significant rainfall, runoff, rivers, lakes, and springs, fed by high water table conditions to sustain periods of flourishing communities of plants, arthropods, reptiles, mammals, and dinosaurs. Strong ground motion perturbations periodically disrupted porous, water-saturated sands with possible surface eruptions, adding to the dynamic activity of the desert regime.

  9. Sedimentary and petrofacies analyses of the Amasiri Sandstone, southern Benue Trough, Nigeria: Implications for depositional environment and tectonic provenance

    NASA Astrophysics Data System (ADS)

    Okoro, A. U.; Igwe, E. O.; Nwajide, C. S.

    2016-11-01

    This study was undertaken to determine the depositional environment, provenance and tectonic setting for the Turonian Amasiri Sandstone, southern Benue Trough, Nigeria, using lithofacies analysis and re-appraisal of petrography of the sandstones. Local stratigraphy and field relationships show a thick succession of shales alternating with elongate/parallel sandstone ridges extending eastwards from Akpoha to Amasiri through Itigidi and Ugep to Apiapum areas. Lithofacies analysis reveals 9 lithofacies suggestive of storm (mass flow) and tidal shelf processes. These include dark grey to black laminated shale/silty mudstones, bioturbated mudstones, coquinoid limestones, very fine-grained bioturbated sandstones with shell hash/debris in places and limestone rip-up clasts, massive and chaotic sandy conglomerate with rip - up clasts, fine to medium-grained, parallel laminated sandstone, hummocky cross-stratified, massive, medium to coarse-grained sandstones, medium to very coarse-grained, planar cross-bedded sandstone, with clay-draped foresets and Ophiomorpha burrows, and coarse-grained trough cross-bedded sandstone. Petrofacies analysis identifies the sandstones as feldspathic and arkosic arenites. Ternary plot of framework mineralogy indicates derivation from an uplifted continental block related to the nearby Oban Massif and Cameroon Basement Complex.

  10. Experimental investigation of the strength and failure behavior of layered sandstone under uniaxial compression and Brazilian testing

    NASA Astrophysics Data System (ADS)

    Yin, Peng-Fei; Yang, Sheng-Qi

    2018-05-01

    As a typical inherently anisotropic rock, layered sandstones can differ from each other in several aspects, including grain size, type of material, type of cementation, and degree of compaction. An experimental study is essential to obtain and convictive evidence to characterize the mechanical behavior of such rock. In this paper, the mechanical behavior of a layered sandstone from Xuzhou, China, is investigated under uniaxial compression and Brazilian test conditions. The loading tests are conducted on 7 sets of bedding inclinations, which are defined as the angle between the bedding plane and horizontal direction. The uniaxial compression strength (UCS) and elastic modulus values show an undulatory variation when the bedding inclination increases. The overall trend of the UCS and elastic modulus values with bedding inclination is decreasing. The BTS value decreases with respect to the bedding inclination and the overall trend of it is approximating a linear variation. The 3D digital high-speed camera images reveal that the failure and fracture of a specimen are related to the surface deformation. Layered sandstone tested under uniaxial compression does not show a typical failure mode, although shear slip along the bedding plane occurs at high bedding inclinations. Strain gauge readings during the Brazilian tests indicate that the normal stress on the bedding plane transforms from compression to tension as the bedding inclination increases. The stress parallel to the bedding plane in a rock material transforms from tension to compression and agrees well with the fracture patterns; "central fractures" occur at bedding inclinations of 0°-75°, "layer activation" occurs at high bedding inclinations of 75°-90°, and a combination of the two occurs at 75°.

  11. Depositional environments and tectonic significance of the Wajid Sandstone of southern Saudi Arabia

    NASA Astrophysics Data System (ADS)

    Dabbagh, Mohamed E.; Rogers, John J. W.

    The Wajid Sandstone, of probable Early Paleozoic age, rests disconformably on crystalline rocks of the southern part of the Arabian shield. Scattered outcrops extend over an area about 450 km north-south and 300 km east-west. The southern part of the formation, near the Yemen border, consists of fluvial sandstones and very minor siltstones and silty shales. The fluvial origin is demonstrated by the presence of fining-upward cycles, channels, trough cross bedding, and absence of all organic traces. The northern part of the outcrop area consists of internally homogeneous, tabular cross-bedded, horizontally bedded sandstones apparently formed in a shallow marine environment. These marine rocks contain trace fossils broadly similar to Skolithos. Abundant cross bedding in both facies of the Wajid indicates a northward transport direction, toward what is now the center of the Arabian shield. The southern part of the Arabian shield, which was cratonized about 500 to 600 Ma ago (Pan-African age), was apparently still a depositional area receiving sediments from a southern source in Early Paleozoic time. Other, older, shields also show a tendency to be areas of deposition shortly after their apparent age of stabilization, becoming sources of clastic sediments only after several hundreds of millions of years. The conversion from basin to uplifted source may indicate a prolonged process of shield maturation after initial stabilization.

  12. Seastacks buried beneath newly reported Lower Miocene sandstone, northern Santa Barbara County, California

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fritsche, A.E.; Hanna, F.M.

    1985-04-01

    Three large, isolated exposures of a light-gray, coarse-grained, thick-bedded sandstone unit occur in the northern San Rafael Mountains of Santa Barbara County, California. These rocks are moderately fossiliferous and contain Vertipecten bowersi, Amussiopecten vanvlecki, Aequipecten andersoni, Otrea howelli, shark teeth, whale bones, and regular echinoid spines. The fossils indicate that the sandstone unit, although previously reported as upper(.) Miocene, correlates best with the lower Miocene Vaqueros Formation. This unit was deposited in angular unconformity on a Cretaceous, greenish-gray turbidite sequence of interbedded sandstone and shale, and onlaps the unconformity erosion surface from west to east, the unit being thicker inmore » the west and older at its base. The underlying Cretaceous sandstone beds are well indurated, and during the eastward transgression of the early Miocene sea, they resisted wave erosion and stood as seastacks offshore of the advancing coastline, thus creating a very irregular topographic surface upon which the Vaqueros Formation was deposited. Some seastacks were as much as 4 m tall, as indicated by inliers of Cretaceous rock surrounded by 4-m thick sections of the Vaqueros Formation.« less

  13. Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Barnhart, Elliott P.; Weeks, Edwin P.; Jones, Elizabeth J. P.

    Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulicmore » conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112-120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ 13C values (-67‰ average), high alkalinity values (22 meq/kg average), relatively positive δ 13C-DIC values (4‰ average), and no detectable higher chain hydrocarbons, NO 3 -, or SO 4 2-. Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situ bacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down

  14. Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

    DOE PAGES

    Barnhart, Elliott P.; Weeks, Edwin P.; Jones, Elizabeth J. P.; ...

    2016-05-04

    Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulicmore » conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112-120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ 13C values (-67‰ average), high alkalinity values (22 meq/kg average), relatively positive δ 13C-DIC values (4‰ average), and no detectable higher chain hydrocarbons, NO 3 -, or SO 4 2-. Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situ bacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down

  15. Use of micro-resistivity imaging tools in developing lower Pennsylvanian Morrow channel sandstone reservoirs, Cheyenne, Kiowa and Lincoln Counties, Colorado

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Germinario, M.P.

    1996-01-01

    In southeastern Colorado, Lower Pennsylvanian Morrow channel sandstones are part of complex valley-fill sequences incised into Morrow marine deposits. Morrow valleys are approximately [1/2] to 1 mile wide. Valley-fill consists of floodplain and channel filling shales, very fine-grained estuarine sandstones and fine- to coarse-grained channel sandstones that are up to 50' thick. Channel sandstones represent a sequence of stacked fluvial bars deposited in braided, anastomosing and meandering fluvial environments. Cross-stratification in channel sandstones can be imaged by micro-resistivity wireline logging tools and interpreted interactively on various workstation software packages. Recognition, interpretation and measurement of current, stoss face, and lateral accretionmore » beds in these sandstones can result in an estimated direction of paleocurrent flow of the channel. Determination of the channel's local paleoflow direction can provide significant sand risk reduction in developmental drilling, especially in 80 acre or less spacing patterns. As the distance between offset drilling locations increases, the reliability of paleoflow prediction decreases, and the corresponding sand risk rises. Lateral accretion bedding in Morrow channel sandstones has proven to be a poor indicator of sand thickening direction, due to the complex stacking of multiple channel sandstones within any given valley-fill sequence. Micro-resistivity imaging reduces risk in Morrow channel sandstone development drilling programs. Furthermore, these interpretation techniques could be applicable in other fluvial channel sandstone plays.« less

  16. Use of micro-resistivity imaging tools in developing lower Pennsylvanian Morrow channel sandstone reservoirs, Cheyenne, Kiowa and Lincoln Counties, Colorado

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Germinario, M.P.

    1996-12-31

    In southeastern Colorado, Lower Pennsylvanian Morrow channel sandstones are part of complex valley-fill sequences incised into Morrow marine deposits. Morrow valleys are approximately {1/2} to 1 mile wide. Valley-fill consists of floodplain and channel filling shales, very fine-grained estuarine sandstones and fine- to coarse-grained channel sandstones that are up to 50` thick. Channel sandstones represent a sequence of stacked fluvial bars deposited in braided, anastomosing and meandering fluvial environments. Cross-stratification in channel sandstones can be imaged by micro-resistivity wireline logging tools and interpreted interactively on various workstation software packages. Recognition, interpretation and measurement of current, stoss face, and lateral accretionmore » beds in these sandstones can result in an estimated direction of paleocurrent flow of the channel. Determination of the channel`s local paleoflow direction can provide significant sand risk reduction in developmental drilling, especially in 80 acre or less spacing patterns. As the distance between offset drilling locations increases, the reliability of paleoflow prediction decreases, and the corresponding sand risk rises. Lateral accretion bedding in Morrow channel sandstones has proven to be a poor indicator of sand thickening direction, due to the complex stacking of multiple channel sandstones within any given valley-fill sequence. Micro-resistivity imaging reduces risk in Morrow channel sandstone development drilling programs. Furthermore, these interpretation techniques could be applicable in other fluvial channel sandstone plays.« less

  17. Chemical Interactions of Uranium in Water, Sediments, and Plants Along a Watershed Adjacent to the Abandoned Jackpile Mine

    NASA Astrophysics Data System (ADS)

    Blake, J.; De Vore, C. L.; Avasarala, S.; Ali, A.; Roldan, C.; Bowers, F.; Spilde, M.; Artyushkova, K.; Cerrato, J.

    2015-12-01

    The chemical interactions, mobility, and plant uptake of uranium (U) near abandoned mine wastes was investigated along the Rio Paguate, adjacent to the Jackpile Mine, located in Laguna Pueblo, New Mexico. Elevated U concentrations in surface water adjacent to mine waste range from 30 to 710 μg/L seasonally and decrease to 5.77 to 10.0 μg/L at a wetland 4.5 kilometers downstream of the mine. Although U concentrations in stream water are elevated, aqua regia acid digestions performed on co-located stream bed and stream bank sediments reveal that there is limited U accumulation on sediments along the reach between the mine and wetland, with most sediment concentrations being near the 3 mg/kg crustal average. However, U concentrations in sediments in the wetland are 4 times the background concentrations in the area. Individual results from salt cedar roots, stems, and leaves collected along the river transect show higher U concentrations in the roots adjacent to the mine waste (20 and 55 mg/kg) and lower in the stems and leaves. Translocation values calculated below 1 are evident in many of the plant samples, suggesting that U root to shoot translocation is minimal and U is accumulating in the roots. Concentrations of U in salt cedar roots from downstream of the mine waste decrease to 15 mg/kg. X-ray photoelectron spectroscopy analysis on sediment samples adjacent to the mine waste show a 75:25% ratio of Fe(III) to Fe(II), which can have an effect on adsorption properties. Electron microprobe results suggest that the ore in this area is present as a uranium-phosphate phase. Our results suggest that dilution, uptake by plants, and U sorption to wetland sediments are the dominant factors that help to decrease the U concentrations downstream of the mine.

  18. Hydrogeochemistry and coal-associated bacterial populations from a methanogenic coal bed

    USGS Publications Warehouse

    Barnhart, Elliott P.; Weeks, Edwin P.; Jones, Elizabeth J.P.; Ritter, Daniel J.; McIntosh, Jennifer C.; Clark, Arthur C.; Ruppert, Leslie F.; Cunningham, Alfred B.; Vinson, David S.; Orem, William H.; Fields, Matthew W.

    2016-01-01

    Biogenic coalbed methane (CBM), a microbially-generated source of natural gas trapped within coal beds, is an important energy resource in many countries. Specific bacterial populations and enzymes involved in coal degradation, the potential rate-limiting step of CBM formation, are relatively unknown. The U.S. Geological Survey (USGS) has established a field site, (Birney test site), in an undeveloped area of the Powder River Basin (PRB), with four wells completed in the Flowers-Goodale coal bed, one in the overlying sandstone formation, and four in overlying and underlying coal beds (Knoblach, Nance, and Terret). The nine wells were positioned to characterize the hydraulic conductivity of the Flowers-Goodale coal bed and were selectively cored to investigate the hydrogeochemistry and microbiology associated with CBM production at the Birney test site. Aquifer-test results indicated the Flowers-Goodale coal bed, in a zone from about 112 to 120 m below land surface at the test site, had very low hydraulic conductivity (0.005 m/d) compared to other PRB coal beds examined. Consistent with microbial methanogenesis, groundwater in the coal bed and overlying sandstone contain dissolved methane (46 mg/L average) with low δ13C values (−67‰ average), high alkalinity values (22 meq/kg average), relatively positive δ13C-DIC values (4‰ average), and no detectable higher chain hydrocarbons, NO3−, or SO42−. Bioassay methane production was greatest at the upper interface of the Flowers-Goodale coal bed near the overlying sandstone. Pyrotag analysis identified Aeribacillus as a dominant in situbacterial community member in the coal near the sandstone and statistical analysis indicated Actinobacteria predominated coal core samples compared to claystone or sandstone cores. These bacteria, which previously have been correlated with hydrocarbon-containing environments such as oil reservoirs, have demonstrated the ability to produce biosurfactants to break down

  19. Facies-controlled fluid migration patterns and subsequent reservoir collapse by depressurization - the Entrada Sandstone, Utah

    NASA Astrophysics Data System (ADS)

    Sundal, A.; Skurtveit, E.; Midtkandal, I.; Hope, I.; Larsen, E.; Kristensen, R. S.; Braathen, A.

    2016-12-01

    The thick and laterally extensive Middle Jurassic Entrada Sandstone forms a regionally significant reservoir both in the subsurface and as outcrops in Utah. Individual layers of fluvial sandstone within otherwise fine-grained aeolian dunes and silty inter-dune deposits of the Entrada Earthy Member are of particular interest as CO2 reservoir analogs to study injectivity, reservoir-caprock interaction and bypass systems. Detailed mapping of facies and deformation structures, including petrographic studies and core plug tests, show significant rock property contrasts between layers of different sedimentary facies. Beds representing fluvial facies appear as white, medium-grained, well-sorted and cross-stratified sandstone, displaying high porosity, high micro-scale permeability, low tensile strength, and low seismic velocity. Subsequent to deposition, these beds were structurally deformed and contain a dense network of deformation bands, especially in proximity to faults and injectites. Over- and underlying low-permeability layers of inter-dune aeolian facies contain none or few deformation bands, display significantly higher rock strengths and high seismic velocities compared to the fluvial inter-beds. Permeable units between low-permeability layers are prone to become over-pressured during burial, and the establishment of fluid escape routes during regional tectonic events may have caused depressurization and selective collapse of weak layers. Through-cutting, vertical sand pipes display large clasts of stratified sandstone suspended in remobilized sand matrix, and may have served as permeable fluid conduits and pressure vents before becoming preferentially cemented and plugged. Bleached zones around faults and fractures throughout the succession indicate leakage and migration of reducing fluids. The fluvial beds are porous and would appear in wireline logs and seismic profiles as excellent reservoirs; whereas due to dense populations of deformation bands they may in

  20. Diagenesis Along Fractures in an Eolian Sandstone, Gale Crater, Mars

    NASA Technical Reports Server (NTRS)

    Ming, D. W.; Yen, A. S.; Rampe, E. B.; Grotzinger, J. P.; Blake, D. F.; Bristow, T. F.; Chipera, S. J.; Downs, R.; Morris, R. V.; Morrison, S. M.; hide

    2016-01-01

    The Mars Science Laboratory rover Curiosity has been exploring sedimentary deposits in Gale crater since August 2012. The rover has traversed up section through approx.100 m of sedimentary rocks deposited in fluvial, deltaic, lacustrine, and eolian environments (Bradbury group and overlying Mount Sharp group). The Stimson formation lies unconformable over a lacustrine mudstone at the base of the Mount Sharp group and has been interpreted to be a cross-bedded sandstone of lithified eolian dunes. Mineralogy of the unaltered Stimson sandstone consists of plagioclase feldspar, pyroxenes, and magnetite with minor abundances of hematite, and Ca-sulfates (anhydrite, bassanite). Unaltered sandstone has a composition similar to the average Mars crustal composition. Alteration "halos" occur adjacent to fractures in the Stimson. Fluids passing through these fractures have altered the chemistry and mineralogy of the sandstone. Silicon and S enrichments and depletions in Al, Fe, Mg, Na, K, Ni and Mn suggest aqueous alteration in an open hydrologic system. Mineralogy of the altered Stimson is dominated by Ca-sulfates, Si-rich X-ray amorphous materials along with plagioclase feldspar, magnetite, and pyroxenes, but less abundant in the altered compared to the unaltered Stimson sandstone and lower pyroxene/plagioclase feldspar. The mineralogy and geochemistry of the altered sandstone suggest a complicated history with several (many?) episodes of aqueous alteration under a variety of environmental conditions (e.g., acidic, alkaline).

  1. Evidence for preferential flow through sandstone aquifers in Southern Wisconsin

    USGS Publications Warehouse

    Swanson, S.K.; Bahr, J.M.; Bradbury, K.R.; Anderson, K.M.

    2006-01-01

    Sandstones often escape extensive hydrogeologic characterization due to their high primary porosity and perceived homogeneity of permeability. This study provides evidence for laterally extensive, high permeability zones in the Tunnel City Group, an undeformed, Cambrian-aged sandstone unit that exists in the subsurface throughout much of central and southern Wisconsin, USA. Several discrete high-permeability zones were identified in boreholes using flow logging and slug tests, and the interconnectedness of the features was tested using a site-specific numerical model for springs in the region. Explicit incorporation of a high-permeability layer leads to improvements in the flux calibration over simulations that lack the features, thus supporting the hydraulic continuity of high-permeability zones in the sandstone aquifer over tens of kilometers. The results suggest that stratigraphically controlled heterogeneities like contrasts in lithology or bedding-plane fractures, which have been shown to strongly influence the flow of groundwater in more heterogeneous sedimentary rocks, may also deserve close examination in sandstone aquifers. ?? 2005 Elsevier B.V. All rights reserved.

  2. Palaeogeography of Late Triassic red-beds in Singapore and the Indosinian Orogeny

    NASA Astrophysics Data System (ADS)

    Oliver, Grahame; Prave, Anthony

    2013-10-01

    A red-bed facies of the Upper Triassic Jurong Formation has been logged on Sentosa Island, Singapore. An overall coarsening and thickening-upward pattern is well developed. The lower part of the section is dominated by purple-red, massive to finely laminated illite-smectite-kaolin-rich mudstones containing thin, discontinuous lenses of fine sandstone marked by low-angle lamination and small ripples. One dinosaur-like foot print has been discovered in a loose block of red mudstone. It is concluded that this is a lacustrine sequence and it is proposed to name the lake, Lake Sentosa. The upper part of the sequence consists of flat-laminated to trough cross-bedded medium-grained sandstone and granule to cobble conglomerates alternating with purple-red mudstone. The mudstone-sandstone packages are arranged in decametre-scale coarsening-upward cycles. The channelling and decimetre-scale cross-bedding characterising the sandstone and conglomeratic beds is evidence for deposition by flashy fluvial flood processes, possibly feeding into the lake as a fresh water delta. One possible dinosaur trackway in granule size conglomerate has been located. Detrital zircon U-Pb ages vary from 2.7 Ba to 209 Ma with significant populations at ˜245 Ma and 220 Ma. These ages throw light on the timing of the Indosinian Orogeny. The molasse red-beds of the Jurong Formation were deposited in a half graben formed in the hangingwall of the Bukit Timah Fault when central Peninsular Malaysia went into extension following the climax of the Indosinian Orogeny in the Late Triassic.

  3. Depositional environments and sedimentology of Vinita Beds, Richmond basin, Virginia

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kornfeld, I.E.

    The Carnian (middle to late Middle Triassic Age) Richmond basin of northeast Virginia is the oldest of the exposed Newark rift basins of the eastern seaboard. These basins formed during the Mesozoic divergence of the continents. As presently defined, the Richmond basin is a large synclinal feature measuring 32 mi (53 km) long by 8 mi (13 km) wide, and is located west of Richmond, Virginia, and east of Amelia, Virginia. Sediments of the Richmond basin have been assigned to the Richmond Group and have been stratigraphically subdivided into the following informal units, oldest to youngest: coarse boulder breccias, coalmore » measures, Vinita Beds, and Otterdale Sandstone. The Vinita Beds are composed of arkosic sandstones, shales, siltstones, and minor amounts of coal, and are mineralogically immature. They are composed to angular to subrounded rock fragments, quartz, and feldspars, and are high micaceous and kaolinitic. In places, feldspars make up as much as 50% of the rock. Sandstones and conglomerates are cross-bedded and channeled, and shales and siltstones are thinly laminated. The Vinita Beds are rich in fossil fish, branchiopods, and plant fragments. These rocks were deposited in braided streams as well as in paludal and possible lacustrine environments in a humid and heavily vegetated setting.« less

  4. The Manciano Sandstone: a shoreface deposit of Miocene basins of the Northern Apennines, Italy

    NASA Astrophysics Data System (ADS)

    Martini, I. P.; Cascella, A.; Rau, A.

    1995-09-01

    Well exposed, diamond-line cut, quarry-exposures of the Manciano Sandstone allow a detailed analysis of sandy, fossiliferous, nearshore deposits of the shelf of the Northern Apennines. The Manciano Sandstone is characterized by medium to very coarse, washed, fairly well sorted, lithic sandstone, with thin interlayers of sandy conglomerates. It displays two principal, rhythmically alternating sandy facies: (a) slightly burrowed (mostly Macaronichnus, Ophiomorpha, Skolithos) units, trough cross-bedded, locally showing possible tidal bundles with few whole Scutella (echinoid) shells reworked on foresets, or occasional large-scale (approximately 2 m) planar cross-bedded, bar-accretion units; and (b) slightly finer, darker-coloured reddish-brown sandstone units, heavily bioturbated ( Cruziana-Skolithos) ichnofauna) representing slightly more sheltered settings. Large oysters are present in near-living position in a few thin layers and, more commonly, as reworked, comminuted fragments in sandy layers. Many calcareous pebbles and oyster fragments are bored. Other fossils consist of echinoids ( Scutella), some balanids and reworked foraminifera and bryozoa. The Manciano sands were deposited primarily in a wave-dominated shoreface, containing migrating bars/ridges and affected by wave-induced, possibly tidal-enhanced currents. This tidal influence confirms the opening of the Miocene Apenninic Sea to oceans, both the developing Atlantic Ocean to the west and, through a long, narrow seaway, the Asian portion of the Tethys Sea to the east.

  5. Hydrocarbon Potential in Sandstone Reservoir Isolated inside Low Permeability Shale Rock (Case Study: Beruk Field, Central Sumatra Basin)

    NASA Astrophysics Data System (ADS)

    Diria, Shidqi A.; Musu, Junita T.; Hasan, Meutia F.; Permono, Widyo; Anwari, Jakson; Purba, Humbang; Rahmi, Shafa; Sadjati, Ory; Sopandi, Iyep; Ruzi, Fadli

    2018-03-01

    Upper Red Bed, Menggala Formation, Bangko Formation, Bekasap Formation and Duri Formationare considered as the major reservoirs in Central Sumatra Basin (CSB). However, Telisa Formation which is well-known as seal within CSB also has potential as reservoir rock. Field study discovered that lenses and layers which has low to high permeability sandstone enclosed inside low permeability shale of Telisa Formation. This matter is very distinctive and giving a new perspective and information related to the invention of hydrocarbon potential in reservoir sandstone that isolated inside low permeability shale. This study has been conducted by integrating seismic data, well logs, and petrophysical data throughly. Facies and static model are constructed to estimate hydrocarbon potential resource. Facies model shows that Telisa Formation was deposited in deltaic system while the potential reservoir was deposited in distributary mouth bar sandstone but would be discontinued bedding among shale mud-flat. Besides, well log data shows crossover between RHOB and NPHI, indicated that distributary mouth bar sandstone is potentially saturated by hydrocarbon. Target area has permeability ranging from 0.01-1000 mD, whereas porosity varies from 1-30% and water saturation varies from 30-70%. The hydrocarbon resource calculation approximates 36.723 MSTB.

  6. Bedding Pattern Interpreted as Martian Delta Deposition

    NASA Image and Video Library

    2014-12-08

    On March 25, 2014, view from the Mastcam on NASA Curiosity Mars rover looks southward at the Kimberley waypoint. Multiple sandstone beds show systematic inclination to the south suggesting progressive build-out of delta sediments.

  7. Alternative marine and fluvial models for the non-fossiliferous quartzitic sandstones of the Early Proterozoic Daspoort Formation, Transvaal Sequence of southern Africa

    NASA Astrophysics Data System (ADS)

    Eriksson, P. G.; Schreiber, U. M.; van der Neut, M.; Labuschagne, H.; Van Der Schyff, W.; Potgieter, G.

    1993-04-01

    This paper discusses some of the problems related to the palaeoenvironmental interpretation of non-fossiliferous, early Precambrian, recrystallised quartzitic sandstones, using the Early Proterozoic Daspoort Formation, Transvaal Sequence of southern Africa as a case study. These cross-bedded and planar stratified rocks have been interpreted previously as shallow marine deposits, based on limited studies of areas with well-exposed, relatively undeformed outcrops. This postulate rests largely on the apparently mature nature of the recrystallised sandstones and their thin bedding. Examination of outcrops throughout the preserved basin, including those which have been deformed and metamorphosed, reveals the presence of subordinate immature sandstones. Lateral facies relationships permit an alternative distal fan-fluvial braidplain model to be proposed. This is compatible with collected palaeocurrent data, thicknes trends and results of thin section petrography.

  8. Integrated interpretation of C-8 and G-61 sandstones at Badak and Nilam fields in Sanga-Sanga block of east Kalimantan, Indonesia

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ade, W.C.; Suwarlan, W.

    1989-03-01

    Huffco's Badak and Nilam fields are giant gas fields that together currently produce more than 1.0 bcf of gas per day from sandstones within the Miocene Balikpapan beds. The reservoir sandstones were deposited within a thick regressive deltaic sequence that includes coals, shales, and occasional limestones. Wells typically encounter multiple stacked pay sandstones at depths ranging from about 5500 ft to more than 13,000 ft. Individual sandstone thicknesses can vary from several feet to more than 20 ft. Abrupt lateral stratigraphic variations in sandstone thickness are the rule rather than the exception. Sandstone reservoir interpretations are based on an integratedmore » approach by incorporating the study of well logs, cores, seismic sections, normal moveout-corrected gathers, amplitude variations with offset (AVO) graphs, and pressure and reservoir performance data.« less

  9. Sandstone units of the Lee Formation and related strata in eastern Kentucky

    USGS Publications Warehouse

    Rice, Charles L.

    1984-01-01

    sandstone and conglomerate. The Dark Ridge and Hensley Members are mostly shale, siltstone, thin-bedded silty sandstone, and coal. The lower three of these members, the Pinnacle Overlook, Chadwell, and White Rocks Sandstone, are assigned to the Upper Mississippian Series because they intertongue with marine reddish or greenish shale and siltstone of the Pennington Formation or equivalent strata that contain a Late Mississippian fauna. The overlying quartzose sandstone members of the Lee commonly have coalified plant remains and impressions of plants and are Early to Middle Pennsylvanian in age; they are generally associated with terrestrial shale and siltstone containing coal beds and pinch out eastward into subgraywacke, siltstone, and shale. Although marine members commonly are bimodal, resultant transport directions for both marine and terrestrial members are southwesterly as determined by crossbedding. Thickness variations of the Middlesboro Member in the Cumberland overthrust sheet suggest that it represents tills of at least three major southwesterly trending paleovalleys. Thickness variations of the Bee Rock Sandstone Member east of Rocky Face fault and the combined Bee Rock and Naese Sandstone Members west of Rocky Face fault suggest that these members represent tills of at least two major southwesterly trending paleovalleys. East of Rocky Face fault, the Bee Rock is generally the uppermost member of the Lee; west of the fault, the overlying Naese is at the top. The Naese may range in age from Early to Middle Pennsylvanian and is partly or wholly equivalent to the Rockcastle Sandstone member of the Lee Formation in the area of the Pottsville Escarpment. The Mississippian-Pennsylvanian systemic boundary in the area of the Cumberland overthrust sheet in most places has been placed at an unconformity at the base of the Middlesboro Member; locally it is projected at the base of shales of the underlying Dark Ridge Member or equivalent strata in the Penningto

  10. Stratigraphy and depositional environment of unnamed (lower Miocene) submarine-fan sandstone unit in Sierra Madre and San Rafael Mountains, northeastern Santa Barbara County, California

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Thomas, G.D.; Fritsche, A.E.; Condon, M.W.

    1988-03-01

    A relatively thick and extensive, previously unnamed, lower Miocene sandstone unit occurs in the central Sierra Madre and in the Hurricane Deck area of the San Rafael Mountains of northeastern Santa Barbara County, California. It is underlain conformably and interfingers with a dark mudstone that correlates with the Soda Lake Shale Member of the Vaqueros Formation; it is overlain conformably and interfingers with a brown shale that correlates with the Saltos Member of the Monterey Shale. Northeastern exposures along the north flank of the Sierra Madre are almost exclusively medium to coarse-grained, structureless sandstone with scattered pebbly conglomerate beds. Thicknessmore » ranges from zero in the southeastern part of the Sierra Madre to 70 m in the northeast, 75 m in the northwest, and 600 m in the central part of the range. Toward the southwest in the Hurricane Deck area of the San Rafael Mountains, the unit becomes thicker and more extensively interbedded with mudstone. Lithology of the unit consists of 0.3-3.5 m thick beds of medium to coarse-grained, structureless to vaguely graded sandstone with scoured contacts at the base. Sandstone beds 0.3-3.0 m thick, which are more distinctly graded from coarse to very fine are also present. The interbedded mudstone commonly is bioturbated, so bedding is indistinct. Thickness ranges from 1020 m in the central part of the area to 750 m toward the southwest and 92 m toward the northwest. The unit most likely represents deposition in a submarine-canyon and fan complex that had its channel head in the northeast and spread southwestward into a thick sequence of submarine-fan sandstone lobes, which were confined in a narrow west-trending trough.« less

  11. Mixed fluvial systems of Messak Sandstone, a deposit of Nubian lithofacies, southwestern Libya

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lorenz, J.C.

    1987-05-01

    The Messak Sandstone is a coarse to pebbly, tabular cross-bedded, Lower Cretaceous deposit of the widespread Nubian lithofacies. It was deposited at the northern edge of the Murzuq basin in southwestern Libya. Although the sedimentary record is predominantly one of braided fluvial systems, a common subfacies within the formation is interpreted to record the passage of straight-crested sand waves across laterally migrating point bars in sinuous rivers, similar to the pattern documented by Singh and Kumar on the modern Ganga and Yamuna Rivers. Because the sand waves were larger on the lower parts of the point bars, lateral migration createdmore » diagnostic thinning-upward, unidirectional cosets of tabular cross-beds as well as fining-upward, grain-size trends. Common, thick, interbedded claystones, deposited in associated paludal and lacustrine environments, and high variance in cross-bed dispersion patterns also suggest the local presence of sinuous fluvial systems within the overall braided regime. The Messak Sandstone contains some of the features that led Harms et al to propose an unconventional low-sinuosity fluvial environment for the Nubian lithofacies in Egypt, and the continuously high water levels of this model may explain channel-scale clay drapes and overturned cross-beds in the Messak. However, most of the Messak characteristics are incompatible with the low-sinuosity model, suggesting instead that the fluvial channels in the Murzuq basin alternated between braided and high-sinuosity patterns.« less

  12. Diagenetic contrast of sandstones in hydrocarbon prospective Mesozoic rift basins (Ethiopia, UK, USA)

    NASA Astrophysics Data System (ADS)

    Wolela, A.

    2014-11-01

    Diagenetic studied in hydrocarbon-prospective Mesozoic rift basins were carried out in the Blue Nile Basin (Ethiopia), Ulster Basin (United Kingdom) and Hartford Basin (United States of America). Alluvial fan, single and amalgamated multistorey meandering and braided river, deep and shallow perennial lake, shallow ephemeral lake, aeolian and playa mud-flat are the prominent depositional environments. The studied sandstones exhibit red bed diagenesis. Source area geology, depositional environments, pore-water chemistry and circulation, tectonic setting and burial history controlled the diagenetic evolution. The diagenetic minerals include: facies-related minerals (calcrete and dolocrete), grain-coating clay minerals and/or hematite, quartz and feldspar overgrowths, carbonate cements, hematite, kaolinite, illite-smectite, smectite, illite, chlorite, actinolite, laumontite, pyrite and apatite. Diversity of diagenetic minerals and sequence of diagenetic alteration can be directly related to depositional environment and burial history of the basins. Variation in infiltrated clays, carbonate cements and clay minerals observed in the studied sandstones. The alluvial fan and fluviatile sandstones are dominated by kaolinite, illite calcite and ferroan calcite, whereas the playa and lacustrine sandstones are dominated by illite-smectite, smectite-chlorite, smectite, chlorite, dolomite ferroan dolomite and ankerite. Albite, pyrite and apatite are predominantly precipitated in lacustrine sandstones. Basaltic eruption in the basins modified mechanically infiltrated clays to authigenic clays. In all the studied sandstones, secondary porosity predominates over primary porosity. The oil emplacement inhabited clay authigenesis and generation of secondary porosity, whereas authigenesis of quartz, pyrite and apatite continued after oil emplacement.

  13. The interplay of fractures and sedimentary architecture: Natural gas from reservoirs in the Molina sandstones, Piceance Basin, Colorado

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lorenz, J.C.

    1997-03-01

    The Molina Member of the Wasatch Formation produces natural gas from several fields along the Colorado River in the Piceance Basin, northwestern Colorado. The Molina Member is a distinctive sandstone that was deposited in a unique fluvial environment of shallow-water floods. This is recorded by the dominance of plane-parallel bedding in many of the sandstones. The Molina sandstones crop out on the western edge of the basin, and have been projected into the subsurface and across the basin to correlate with thinner sandy units of the Wasatch Formation at the eastern side of the basin. Detailed study, however, has shownmore » that the sedimentary characteristics of the type-section Molina sandstones are incompatible with a model in which the eastern sandstones are its distal facies equivalent. Rather, the eastern sandstones represent separate and unrelated sedimentary systems that prograded into the basin from nearby source-area highlands. Therefore, only the subsurface {open_quotes}Molina{close_quotes} reservoirs that are in close proximity to the western edge of the basin are continuous with the type-section sandstones. Reservoirs in the Grand Valley and Rulison gas fields were deposited in separate fluvial systems. These sandstones contain more typical fluvial sedimentary structures such as crossbeds and lateral accretion surfaces. Natural fractures play an important role in enhancing the conductivity and permeability of the Molina and related sandstones of the Wasatch Formation.« less

  14. Geomechanical Modeling of Deformation Banding in the Navajo Sandstone, San Rafael Monocline, Utah

    NASA Astrophysics Data System (ADS)

    Gutierrez, M.; Sundal, A.; Petrie, E. S.

    2017-12-01

    Deformation bands are ubiquitous geological features in many types of rocks. Depending on their micro-structure, they can act either as conduits or barriers to fluid flow. Given the significant roles deformation bands play in fluid flow and chemical transport in rocks, it is important to develop fundamental understanding of their origin, and their characteristics as they relate with the host rock properties and their depositional and structural-geological history. We present a forward-modeling technique based on the geomechanical Bifurcation Theory (BT) to predict the formation of deformation bands in sandstone. According to BT, the formation of deformation bands is a result of strain location, which in turn stems from instability in the stress-strain response of materials during loading. Due to bifurcation, a material which undergoes homogeneous deformation can reach a point at which the material experiences instability and deformation starts to become non-homogenous. We implemented BT in the commercially-available geomechanical code FLAC (Fast Langragian Analysis of Continua) and applied it in the field-scale modeling of deformation banding in the Navajo Sandstone in the San Rafael Monocline in Utah induced by fault propagation folding. The results show that geomechanical modeling using BT has a powerful potential to simulate the physical processes in the formation of deformation banding in rocks. Predicted deformation bands, specifically the pervasive bedding-parallel bands in the Navajo sandstone formation, normal faulting in the upper limb and reverse faulting in the lower limb, are generally in agreement with field observations. Predictions indicate that the pervasive bedding-parallel bands in the Navajo Sandstone are transitional compaction-shear bands with alternating zones of volumetric compaction and dilation. These predictions are consistent with petrographic analysis of thin sections of rock samples from the Navajo Sandstone. The most important

  15. Hydrogeology of the Potsdam Sandstone in northern New York

    USGS Publications Warehouse

    Williams, John H.; Reynolds, Richard J.; Franzi, David A.; Romanowicz, Edwin A.; Paillet, Frederick L.

    2010-01-01

    The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m2/d but typically is less than 10 m2/d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends

  16. The fauna of the Batesville sandstone of northern Arkansas

    USGS Publications Warehouse

    Girty, George H.

    1915-01-01

    The beds in northern Arkansas that lie between the Boone limestone (commonly regarded as representing the Burlington and Keokuk epochs) and the Pennsylvanian have been divided into several formations, named, in ascending order, Moorefield shale, Batesville sandstone, Fayetteville shale, and Pitkin limestone. These formations presumably are equivalent to those that hold a corresponding position in the typical Mississippian section of Iowa, Missouri, and Illinois, but the faunas which they have furnished show noteworthy differences from the typical faunas. It has therefore seemed desirable to investigate these faunas, especially as the facies which they present is found also in the faunas of several of the Southern States, such as Oklahoma, Mississippi, and Alabama. With this object in view, I published in 1911 a report on the fossils of the Moorefield shale. The fauna next to be considered in a systematic pursuance of such a plan as I have mentioned is that of the Batesville sandstone, but the fauna of the Batesville sandstone, as is well known, has already been described in a treatise by Prof. Stuart Weller. At first I considered the possibility of pretermitting the Batesville fauna and of substituting Prof. Weller's report for my own in a series of little monographs that are under contemplation. It soon became evident, however, that this would not be satisfactory because, whether by reason of having collections from a number of new localities or by reason of having more extensive collections from old ones, I found that the material at my command considerably increased the number of types known from the Batesville sandstone, among them being a few which were undescribed. In fact, while Prof. Weller's paper discusses only 30 species (aside from a few Bryozoan types not even generically distinguished) the present paper discusses 128 species. On this account it seemed to me essential to redescribe the fauna.

  17. Assessing processes and timescales of sandstone 'peak forest' formation at Wulingyuan (Hunan, China)

    NASA Astrophysics Data System (ADS)

    Fink, David; May, Henne; Huang, He-quing; Fujioka, Toshiyuki; Wray, Robert

    2013-04-01

    Sandstone landscapes around the globe exhibit a surprising variety in terms of their landforms and formative processes. Ultimately, this reflects the wide range of geomorphic controls that dominate on regional scales, such as lithology, physical and chemical weathering, tectonics, and climate . At Wulingyuan, Hunan Province, China, a unique landscape has developed in Devonian sandstone over an area of ~400 km2, the "Wulingyuan peak forest", which is characterized by sheer vertical sandstone pillars over 3000 m in relief, overlayed with a substructure of peaks and walls of up to 350 m height. Due to these spectacular features, the area has become a major tourist attraction, and has recently been declared an UNESCO Global Geopark. Uplift, a densely spaced joint pattern, and the uniformity of sandstone beds have been suggested as major prerequisites for the formation and preservation of the unique morphology around Wulingyuan. We aim to investigate the underlying processes and controls responsible for the "peak forest" by determining a chronological framework for its age, rate of formation and rates of surface erosion. The initiation of uplift ~ 1 Ma ago and subsequent stepwise evolution of the "peak forest" has been inferred from cave sediments and surrounding alluvial terraces. No direct information, however, is available on the shorter-term evolution of the vertical sandstone walls, peaks and pillars. In this study , we (i) consider sampling strategies for applying surface exposure dating (SED) in this challenging morphological setting. (ii) present some first results, and (iii) discuss their significance in providing first estimates on rates of catchment-wide denudation, weathering, retreat of the vertical sandstone walls, and bedrock incision. In combination with a GIS-based assessment of sediment volumes stored in and eroded from the catchment, our data will help to elucidate the relative roles of fluvial, mass-wasting, and weathering processes in the longer

  18. Differentiating submarine channel-related thin-bedded turbidite facies: Outcrop examples from the Rosario Formation, Mexico

    NASA Astrophysics Data System (ADS)

    Hansen, Larissa; Callow, Richard; Kane, Ian; Kneller, Ben

    2017-08-01

    Thin-bedded turbidites deposited by sediment gravity flows that spill from submarine channels often contain significant volumes of sand in laterally continuous beds. These can make up over 50% of the channel-belt fill volume, and can thus form commercially important hydrocarbon reservoirs. Thin-bedded turbidites can be deposited in environments that include levees and depositional terraces, which are distinguished on the basis of their external morphology and internal architecture. Levees have a distinctive wedge shaped morphology, thinning away from the channel, and confine both channels (internal levees) and channel-belts (external levees). Terraces are flat-lying features that are elevated above the active channel within a broad channel-belt. Despite the ubiquity of terraces and levees in modern submarine channel systems, the recognition of these environments in outcrop and in the subsurface is challenging. In this outcrop study of the Upper Cretaceous Rosario Formation (Baja California, Mexico), lateral transects based on multiple logged sections of thin-bedded turbidites reveal systematic differences in sandstone layer thicknesses, sandstone proportion, palaeocurrents, sedimentary structures and ichnology between channel-belt and external levee thin-bedded turbidites. Depositional terrace deposits have a larger standard deviation in sandstone layer thicknesses than external levees because they are topographically lower, and experience a wider range of turbidity current sizes overspilling from different parts of the channel-belt. The thickness of sandstone layers within external levees decreases away from the channel-belt while those in depositional terraces are less laterally variable. Depositional terrace environments of the channel-belt are characterized by high bioturbation intensities, and contain distinctive trace fossil assemblages, often dominated by ichnofabrics of the echinoid trace fossil Scolicia. These assemblages contrast with the lower

  19. Impact of Sauropod Dinosaurs on Lagoonal Substrates in the Broome Sandstone (Lower Cretaceous), Western Australia

    PubMed Central

    Thulborn, Tony

    2012-01-01

    Existing knowledge of the tracks left by sauropod dinosaurs (loosely ‘brontosaurs’) is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous) of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints) beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world. PMID:22662116

  20. Seal evaluation and confinement screening criteria for beneficial carbon dioxide storage with enhanced coal bed methane recovery in the Pocahontas Basin, Virginia

    USGS Publications Warehouse

    Grimm, R.P.; Eriksson, K.A.; Ripepi, N.; Eble, C.; Greb, S.F.

    2012-01-01

    The geological storage of carbon dioxide in Appalachian basin coal seams is one possible sink for sequestration of greenhouse gases, with the added benefit of enhanced-coal bed methane (ECBM) recovery. The Pocahontas Basin (part of the central Appalachian Basin) of southwestern Virginia is a major coal bed methane (CBM) province with production mostly from coal beds in the Lower Pennsylvanian Pocahontas and New River formations. As part of the Southeast Regional Carbon Sequestration Partnership's Phase II research program, a CO 2-injection demonstration well was installed into Lower Pennsylvanian coal bed-methane producing strata in southwest Virginia. Samples of siliciclastic lithologies above coal beds in this Oakwood Field well, and from several other cores in the Nora Field were taken to establish a baseline of the basic confinement properties of overlying strata to test seal competency at local and regional scales.Strata above CBM-producing coal beds in the Pocahontas and New River formations consist of dark-gray shales; silty gray shales; heterolithic siltstones, sandstones, and shales; lithic sandstones, and quartzose sandstones. Standard measurements of porosity, permeability and petrography were used to evaluate potential leakage hazards and any possible secondary storage potential for typical lithologies. Both lithic- and quartz-rich sandstones exhibit only minor porosity, with generally low permeability (<0.042mD). Interconnected porosity and permeability are strongly impacted by diverse cementation types and compaction. Analyzed siliciclastic lithologies are considered tight, with limited primary matrix permeability risks for leakage, providing an ensemble of redundant CO 2-ECBM traps.One of the most promising confining intervals above the major coal bed-methane producing interval is the Hensley Shale Member. Analyses of 1500 geophysical logs in southwest Virginia indicate that this unit is moderately thick (>50ft, 15m), laterally continuous (>3000km 2

  1. Characterization of Petroleum Residue in the Entrada Sandstone, Colorado National Monument

    USGS Publications Warehouse

    Lillis, Paul G.; King, J. David

    2007-01-01

    Introduction As part of the U.S. Geological Survey's (USGS) petroleum resource assessment of the Uinta-Piceance Province, Colorado and Utah, in 2000 (USGS Uinta-Piceance Assessment Team, 2003), some 170 oils, oil stains, and oil seeps were geochemically characterized and divided into genetic types (Lillis and others, 2003). Recognized oil types include Minturn, Phosphoria, Grassy Trail Creek, Mancos, Mesaverde, and Green River. Subsequent to that study, the existence and general locality of petroleum residue in the Middle Jurassic Entrada Sandstone in Colorado National Monument (CNM) was brought to the attention of the authors (Scott and others, 2001). Because the analysis of such non-commercial petroleum deposits commonly yields valuable regional resource-trend information, we collected and characterized the reported CNM petroleum residue and compared the results with identified oil types in the Uinta-Piceance Province. Three samples of Entrada Sandstone with petroleum residue were collected near Little Park Road along the south edge of the CNM in sec.20, T.12S., R.101W. The approximate extent of the petroleum staining was determined by field testing with solvent, and the stains appear to be restricted to the upper part of the 'board beds' unit (informal name, Scott and others, 2001) of the Entrada Sandstone between the two fault traces of the Glade Park fault.

  2. Dzhezkazgan and associated sandstone copper deposits of the Chu-Sarysu basin, Central Kazakhstan

    USGS Publications Warehouse

    Box, Stephen E.; Seltmann, Reimar; Zientek, Michael L.; Syusyura, Boris; Creaser, Robert A.; Dolgopolova, Alla

    2012-01-01

    Sandstone-hosted copper (sandstone Cu) deposits occur within a 200-km reach of the northern Chu-Sarysu basin of central Kazakhstan (Dzhezkazgan and Zhaman-Aibat deposits, and the Zhilandy group of deposits). The deposits consist of Cu sulfide minerals as intergranular cement and grain replacement in 10 ore-bearing members of sandstone and conglomerate within a 600- to 1,000-m thick Pennsylvanian fluvial red-bed sequence. Copper metal content of the deposits ranges from 22 million metric tons (Mt, Dzehzkazgan) to 0.13Mt (Karashoshak in the Zhilandy group), with average grades of 0.85 to 1.7% Cu and significant values for silver (Ag) and rhenium (Re). Broader zones of iron reduction (bleaching) of sandstones and conglomerates of the red-bed sequence extend over 10 km beyond each of the deposits along E-NE-trending anticlines, which began to form in the Pennsylvanian. The bleached zones and organic residues within them are remnants of ormer petroleum fluid accumulations trapped by these anticlines. Deposit sites along these F1anticlines are localized at and adjacent to the intersections of nearly orthogonal N-NW-trending F2synclines. These structural lows served to guide the flow of dense ore brines across the petroleum-bearing anticlines, resulting in ore sulfide precipitation where the two fluids mixed. The ore brine was sourced either from the overlying Early Permian lacustrine evaporitic basin, whose depocenter occurs between the major deposits, or from underlying Upper Devonian marine evaporites. Sulfur isotopes indicate biologic reduction of sulfate but do not resolve whether the sulfate was contributed from the brine or from the petroleum fluids. New Re-Os age dates of Cu sulfides from the Dzhezkazgan deposit indicate that mineralization took place between 299 to 309 Ma near the Pennsylvanian-Permian age boundary. At the Dzhezkazgan and some Zhilandy deposits, F2fold deformation continued after ore deposition. Copper orebodies in Lower Permian

  3. The geometry and lithology of the Cima Sandstone Lentil: a paleoseep-bearing interbed in the Moreno Formation, central California

    NASA Astrophysics Data System (ADS)

    Wheatley, P. V.; Schwartz, H.

    2007-12-01

    The Cima Sandstone Lentil outcrops over a relatively small area on the western side of the San Joaquin Valley in central California. Here this unit can be found in the Panoche Hills in the northern portion of the field area and the Tumey Hills in the southern portion of the field area. The Cima Sandstone resides within the 800m Moreno Formation that spans the Maastrichtian to the Danian. The Moreno Formation comprises four members, which are the Dosados Member, the Tierra Loma Member, the Marca Shale Member, and the Dos Palos Shale Member (of which the Cima Sandstone is an interbed). The Cima Sandstone contains numerous large carbonate mounds, concretions, and pavements, indicating paleoseep activity. The Cima Sandstone has never been studied in detail, but recent interest in sandstone injectites as well as interest in paleoseeps has prompted us to examine this interbed more carefully. The Cima is an immature sandstone composed primarily of quartz along with small amounts of micas and feldspars as well as varying amounts of glauconite. These minerals are generally cemented by carbonate but, occasionally, iron oxide cement is present locally. Much variation exists within the Cima Sandstone Lentil and we seek to characterize and understand this variation. One of the most obvious sources of variability is the thickness of the unit itself. The thickness ranges from near 60m in the northern Panoche Hills to only 9m in the Tumey Hills. Induration also varies noticeably, from well cemented in the north, to unconsolidated in the south. Similarly, the sandstone is grain-supported and houses some depositional structures in the northern outcrops but becomes largely matrix-supported and lacking bedding in the southern outcrops. Preliminary data suggests that proximity to carbonate concretions, fluid conduits, and underlying injectites may have some influence over grain size and sorting.

  4. Elemental Gains/Losses Associated with Alteration Fractures in an Eolian Sandstone, Gale Crater, Mars

    NASA Technical Reports Server (NTRS)

    Ming, D. W.; Yen, A. S.; Gellert, R.; Sutter, B.; Berger, J. A.; Thompson, L. M.; Schmidt, M. E.; Morris, R. V.; Treiman, A. H.

    2016-01-01

    The Mars Science Laboratory rover Curiosity has traversed up section through approximately 100 m of sedimentary rocks deposited in fluvial, deltaic, lacustrine, and eolian environments (Bradbury group and overlying Mount Sharp group). The Stimson formation unconformably overlies a lacustrine mudstone at the base of the Mount Sharp group and has been interpreted to be a cross-bedded sandstone of lithified eolian dunes. Unaltered Stimson sandstone has a basaltic composition similar to the average Mars crustal composition, but is more variable and ranges to lower K and higher Al. Fluids passing through alteration "halos" adjacent to fractures have altered the chemistry and mineralogy of the sandstone. Elemental mass gains and losses in the alteration halos were quantified using immobile element concentrations, i.e., Ti (taus). Alteration halos have elemental gains in Si, Ca, S, and P and large losses in Al, Fe, Mn, Mg, Na, K, Ni, and Zn. Mineralogy of the altered Stimson is dominated by Ca-sulfates, Si-rich X-ray amorphous materials along with plagioclase feldspar, magnetite, and pyroxenes. The igneous phases were less abundant in the altered sandstone with a lower pyroxene/plagioclase feldspar. Large elemental losses suggest acidic fluids initially removed these elements (Al mobile under acid conditions). Enrichments in Si, Ca, and S suggest secondary fluids (possibly alkaline) passed through these fractures leaving behind X-ray amorphous Si and Ca-sulfates. The mechanism for the large elemental gains in P is unclear. The geochemistry and mineralogy of the altered sandstone suggests a complicated diagenetic history with multiple episodes of aqueous alteration under a variety of environmental conditions (e.g., acidic, alkaline).

  5. Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

    USGS Publications Warehouse

    Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

    1989-01-01

    Coal beds are considered to be a major source of nonassociated gas in the Rocky Mountain basins of the United States. In the San Juan basin of northwestern New Mexico and southwestern Colorado, significant quantities of natural gas are being produced from coal beds of the Upper Cretaceous Fruitland Formation and from adjacent sandstone reservoirs. Analysis of gas samples from the various gas-producing intervals provided a means of determining their origin and of evaluating coal beds as source rocks. The rank of coal beds in the Fruitland Formation in the central part of the San Juan basin, where major gas production occurs, increases to the northeast and ranges from high-volatile B bituminous coal to medium-volatile bituminous coal (Rm values range from 0.70 to 1.45%). On the basis of chemical, isotopic and coal-rank data, the gases are interpreted to be thermogenic. Gases from the coal beds show little isotopic variation (??13C1 values range -43.6 to -40.5 ppt), are chemically dry (C1/C1-5 values are > 0.99), and contain significant amounts of CO2 (as much as 6%). These gases are interpreted to have resulted from devolatilization of the humic-type bituminous coal that is composed mainly of vitrinite. The primary products of this process are CH4, CO2 and H2O. The coal-generated, methane-rich gas is usually contained in the coal beds of the Fruitland Formation, and has not been expelled and has not migrated into the adjacent sandstone reservoirs. In addition, the coal-bed reservoirs produce a distinctive bicarbonate-type connate water and have higher reservoir pressures than adjacent sandstones. The combination of these factors indicates that coal beds are a closed reservoir system created by the gases, waters, and associated pressures in the micropore coal structure. In contrast, gases produced from overlying sandstones in the Fruitland Formation and underlying Pictured Cliffs Sandstone have a wider range of isotopic values (??13C1 values range from -43.5 to -38

  6. Geochemistry of sandstones from the Pliocene Gabir Formation, north Marsa Alam, Red Sea, Egypt: Implication for provenance, weathering and tectonic setting

    NASA Astrophysics Data System (ADS)

    Zaid, Samir M.

    2015-02-01

    Petrographic, major and trace element compositions of sandstones from the Pliocene Gabir Formation, Central Eastern Desert, Egypt have been investigated to determine their provenance, intensity of paleo-weathering of the source rocks and their depositional tectonic setting. Gabir Formation is composed mainly of sandstones alternating with limestone and shale beds. The Gabir sandstone is yellowish gray to yellowish brown color, calcareous and fossiliferous. The composition of this formation refers to shallow warm agitated marine conditions. Texturally, Gabir sandstones are immature, poorly sorted and grain supported. Abundance of feldspars indicates rapid deposition of sediments from a nearby source rocks. Their average modal composition (Q71.35F16.6L12.05), classifies them as sublitharenite and arkose with subordinate litharenite and subarkose, which is also supported by geochemical study. Chemical analyses revealed that sandstones have high SiO2, K2O > Na2O, and low Fe2O3 values, which are consistent with the modal data. Also, sandstone samples are enriched in most trace elements such as Ba, Sr, Ni, Cr and Zr and depleted in U and Th. The petrography and geochemistry suggest that Gabir sandstones were deposited in an active continental margin basin. They were mainly derived from granitic and low grade metamorphic sources. The CIA values (41.69-74.84) of the Gabir sandstones indicate low to moderate degree of chemical weathering, which may reflect cold and/or arid climate conditions in the source area. The source rocks are probably identified to be Proterozoic granites, metagabbros and metavolcanics, which must have been exposed during rifting, initiated during Oligocene and continued till post Miocene.

  7. Material properties of Godula sandstones and forms and reasons of their deterioration in constructions in industrial environment of the Ostrava region

    NASA Astrophysics Data System (ADS)

    Vavro, Martin; Souček, Kamil; Martinec, Petr; Vavro, Leona; Handzelová, Barbora

    2015-04-01

    by presence of authigenic carbonates (dolomite and calcite) in the matrix and presence of very fine-grained framboidal pyrite localized especially in upper and more lutitic parts of sedimentary bodies. Using the method of 57Fe Mössbauer spectrometry, the Fe2+/Fe3+ ratio close to 1:1 in the crystal structure of glauconite separated from the Godula sandstones was estimated. In glauconite in the Godula sandstone, there is a sufficient quantity of Fe2+ which can be transformed to the Fe3+ form by the weathering process, which causes glauconite instability in the contact with the atmosphere. Structural features of rock are other risk factors influencing weathering. The Godula sandstones represent deep-marine turbiditic sediments with typical graded bedding. Problematic parts represent thin laminas rich in clay matter with dominant illite and/or illite/smectite mixed-layers in upper parts of mined sedimentary bodies. Due to significant structural anisotropy of the Godula sandstones, the final form of stone element degradation is also affected by the relationship between cutting plane during stone block processing and bedding planes. Ignorance of these aspects which influence durability of the Godula sandstones in exterior is the reason of often inappropriate use of stone in building industry in the environment affected by temperature and moisture changes which may result in early rehabilitation or reconstruction of constructions.

  8. "Sydney sandstone": Heritage Stone from Australia

    NASA Astrophysics Data System (ADS)

    Cooper, Barry; Kramar, Sabina

    2014-05-01

    Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

  9. Anatomy and dimensions of fluvial crevasse-splay deposits: Examples from the Cretaceous Castlegate Sandstone and Neslen Formation, Utah, U.S.A.

    NASA Astrophysics Data System (ADS)

    Burns, C. E.; Mountney, N. P.; Hodgson, D. M.; Colombera, L.

    2017-04-01

    Crevasse-splay deposits form a volumetrically significant component of many fluvial overbank successions (up to 90% in some successions).Yet the relationships between the morphological form of accumulated splay bodies and their internal facies composition remains poorly documented from ancient successions. This work quantifies lithofacies distributions and dimensions of exhumed crevasse-splay architectural elements in the Campanian Castlegate Sandstone and Neslen Formation, Mesaverde Group, Utah, USA, to develop a depositional model. Fluvial crevasse-splay bodies thin from 2.1 m (average) to 0.8 m (average) and fine from a coarsest recorded grain size of lower-fine sand to fine silt away from major trunk channel bodies. Internally, the preserved deposits of splays comprise laterally and vertically variable sandstone and siltstone facies associations: proximal parts are dominated by sharp and erosional-based sandstone-prone units, which may be structureless or may comprise primary current lineation on beds and erosional gutter casts; medial parts comprise sets of climbing-ripple strata and small scale deformed beds; distal parts comprise sets of lower-stage plane beds and complex styles of lateral grading into fine-grained floodbasin siltstones and coals. Lithofacies arrangements are used to establish the following: (i) recognition criteria for crevasse-splay elements; (ii) criteria for the differentiation between distal parts of crevasse-splay bodies and floodplain fines; and (iii) empirical relationships with which to establish the extent (ca. 500 m long by 1000 m wide) and overall semi-elliptical planform shape of crevasse-splay bodies. These relationships have been established by high-resolution stratigraphic correlation and palaeocurrent analysis to identify outcrop orientation with respect to splay orientation. This permits lateral changes in crevasse-splay facies architecture to be resolved. Facies models describing the sedimentology and architecture of

  10. Sedimentological analysis and bed thickness statistics from a Carboniferous deep-water channel-levee complex: Myall Trough, SE Australia

    NASA Astrophysics Data System (ADS)

    Palozzi, Jason; Pantopoulos, George; Maravelis, Angelos G.; Nordsvan, Adam; Zelilidis, Avraam

    2018-02-01

    This investigation presents an outcrop-based integrated study of internal division analysis and statistical treatment of turbidite bed thickness applied to a Carboniferous deep-water channel-levee complex in the Myall Trough, southeast Australia. Turbidite beds of the studied succession are characterized by a range of sedimentary structures grouped into two main associations, a thick-bedded and a thin-bedded one, that reflect channel-fill and overbank/levee deposits, respectively. Three vertically stacked channel-levee cycles have been identified. Results of statistical analysis of bed thickness, grain-size and internal division patterns applied on the studied channel-levee succession, indicate that turbidite bed thickness data seem to be well characterized by a bimodal lognormal distribution, which is possibly reflecting the difference between deposition from lower-density flows (in a levee/overbank setting) and very high-density flows (in a channel fill setting). Power law and exponential distributions were observed to hold only for the thick-bedded parts of the succession and cannot characterize the whole bed thickness range of the studied sediments. The succession also exhibits non-random clustering of bed thickness and grain-size measurements. The studied sediments are also characterized by the presence of statistically detected fining-upward sandstone packets. A novel quantitative approach (change-point analysis) is proposed for the detection of those packets. Markov permutation statistics also revealed the existence of order in the alternation of internal divisions in the succession expressed by an optimal internal division cycle reflecting two main types of gravity flow events deposited within both thick-bedded conglomeratic and thin-bedded sandstone associations. The analytical methods presented in this study can be used as additional tools for quantitative analysis and recognition of depositional environments in hydrocarbon-bearing research of ancient

  11. Geometrical characteristics of sandstone with different sample sizes

    NASA Astrophysics Data System (ADS)

    Cheon, D. S.; Takahashi, M., , Dr

    2017-12-01

    In many rock engineering projects such as CO2 underground storage, engineering geothermal system, it is important things to understand the fluid flow behavior in the deep geological conditions. This fluid flow is generally affected by the geometrical characteristics of rock, especially porous media. Furthermore, physical properties in rock may depend on the existence of voids space in rock. Total porosity and pore size distribution can be measured by Mercury Intrusion Porosimetry and the other geometrical and spatial information of pores can be obtained through micro-focus X-ray CT. Using the micro-focus X-ray CT, we obtained the extracted void space and transparent image from the original CT voxel images of with different sample sizes like 1 mm, 2 mm, 3 mm cubes. The test samples are Berea sandstone and Otway sandstone. The former is well-known sandstone and it is used for the standard sample to compared to the result from the Otway sandstone. Otway sandstone was obtained from the CO2CRC Otway pilot site for the CO2 geosequestraion project. From the X-ray scan and ExFACT software, we get the informations including effective pore radii, coordination number, tortuosity and effective throat/pore radius ratio etc. The geometrical information analysis showed that for Berea sandstone and Otway sandstone, there is rarely differences with different sample sizes and total value of coordination number show high porosity, the tortuosity of Berea sandstone is higher than the Otway sandstone. In the future, these information will be used for the permeability of the samples.

  12. Upper Cretaceous Shannon Sandstone reservoirs, Powder River Basin, Wyoming: evidence for organic acid diagenesis?

    USGS Publications Warehouse

    Hansley, P.L.; Nuccio, V.F.

    1992-01-01

    Comparison of the petrology of shallow and deep oil reservoirs in the Upper Cretaceous Shannon Sandstone Beds of the Steele Member of the Cody Shale strongly suggests that organic acids have had a more significant impact on the diagenetic alteration of aluminosilicate grains and carbonate cements in the deep reservoirs than in the shallow reservoirs. Vitrinite reflectance and Rock-Eval measurements, as well as the time-temperature index and kinetic modeling, indicate that deep reservoirs have been subjected to maximum temperatures of approximately 110-120??C, whereas shallow reservoirs have reached only 75??C. -from Authors

  13. Topographic inversion of early interdune deposits, Navajo Sandstone (Lower Jurassic), Colorado Plateau, USA

    NASA Astrophysics Data System (ADS)

    Bromley, Michael

    1992-09-01

    Outliers of Navajo Sandstone (Lower Jurassic Glen Canyon Group) form low paleohills east of the main body of the Formation in the Salt Anticline region of southwestern Colorado. The paleohills consist of interdune deposits which developed topographic inversion during erosion of the Jurassic J-2 unconformity owing to a tough shell of early cemented sandstones and cherty limestones. The interdune deposits accumulated over playa mudstones of the Kayenta Formation which formed in a structural low between the Uncompahgre Uplift and the Paradox Valley salt anticline. Open-framework textures indicate the early formation of quartz or chert cement in sandstone beds immediately above the impermeable playa mudstones. The mudstones enhanced the subsequent formation of wet interdune deposits keeping groundwater near the surface. Microcrystalline quartz cements and fresh feldspars suggest that groundwater was alkaline. A source of alkalinity may have been eolian dust carried from emergent Pennsylvanian evaporite intrusions upwind of the playa deposits. The high specific surface of siliceous and evaporite dusts combined with shallow groundwater and high evaporation rates resulted in the rapid formation of quartzitic silcrete crusts above the playa mudstone aquacludes. As these early silcretes were buried, the impermeable mudstone foundations beneath them continued to serve as aquacludes. The inclined potentiometric surface of perched water tables above the isolated aquacludes intersected the land surface at progressively higher levels as the mudstone lenses were buried. Groundwater moving laterally from above the aquacludes carried dissolved material towards the inclined water tables at their margins. This mobilized material was redeposited as early cement where the capillary fringe intersected the land surface. As the land surface aggraded vertically, the zone of cement formation migrated laterally in response of a change of the relative positions of the land surface and an

  14. Geologic structure and occurrence of gas in part of southwestern New York. Part 1, Structure and gas possibilities of the Oriskany sandstone in Steuben, Yates, and parts of the adjacent counties

    USGS Publications Warehouse

    Bradley, W.H.; Pepper, J.F.

    1941-01-01

    The area covered by this report is in southwestern New York and includes a little more than 3,000 square miles in Steuben and Yates counties and parts of the six adjacent counties. This area has been mapped to determine the structural attitude of the exposed rocks, so as to aid those interested in prospecting for natural gas in the Oriskany sandstone of Lower Devonian age.Because of the gentle regional dip toward the southwest, the youngest beds are exposed in the southwest corner of the area, and progressively older beds crop out northeastward in successive bands that strike generally northwest. All the exposed rocks are of Upper Devonian age except those in a narrow belt at the extreme north edge of the area, where a small thickness of Middle Devonian rocks crops out. The maximum thickness of beds so exposed is nearly 4,000 feet, of which the lower part is predominantly soft dark shale and the upper part predominantly fine-grained sandstone and gray shale. All the beds are marine except a few tongues of continental deposits red shale and sandstone and gray mudstone in the youngest beds. All the beds thicken southeastward, so that there is a northwestward convergence between any two lithologic units in the series. More than 30 key horizons that are persistent and distinctive were mapped, and altitudes on these key horizons served as a basis for constructing the structure contour map. Many of the key horizons are formation or member boundaries, but others are the tops or bottoms of limestone or sandstone beds within formations. All the stratigraphic units mapped are purely lithologic. (See pi. 2.)The Tully limestone, which crops out along the northern border of the area, is an easily recognizable and therefore valuable key bed for subsurface correlations in this part of the State. Below the Tully limestone is a thick body of Middle Devonian shales of the Hamilton group which rests on another valuable key bed, the hard, cherty Onondaga limestone, also of Middle

  15. Bed II Sequence Stratigraphic context of EF-HR and HWK EE archaeological sites, and the Oldowan/Acheulean succession at Olduvai Gorge, Tanzania.

    PubMed

    Stanistreet, Ian G; McHenry, Lindsay J; Stollhofen, Harald; de la Torre, Ignacio

    2018-04-20

    Archaeological excavations at EF-HR and HWK EE allow reassessment of Bed II stratigraphy within the Junction Area and eastern Olduvai Gorge. Application of Sequence Stratigraphic methods provides a time-stratigraphic framework enabling correlation of sedimentary units across facies boundaries, applicable even in those areas where conventional timelines, such as tephrostratigraphic markers, are absent, eroded, or reworked. Sequence Stratigraphically, Bed II subdivides into five major Sequences 1 to 5, all floored by major disconformities that incise deeply into the underlying succession, proving that simple "layer cake" stratigraphy is inappropriate. Previous establishment of the Lemuta Member has invalidated the use of Tuff IIA as the boundary between Lower and Middle Bed II, now redefined at the disconformity between Sequences 2 and 3, a lithostratigraphic contact underlying the succession containing the Lower, Middle, and Upper Augitic Sandstones. HWK EE site records Oldowan technology in the Lower Augitic Sandstone at the base of Sequence 3, within Middle Bed II. We suggest placement of recently reported Acheulean levels at FLK W within the Middle Augitic Sandstone, thus emphasizing that handaxes are yet to be found in earlier stratigraphic units of the Olduvai sequence. This would place a boundary between the Oldowan and Acheulean technologies at Olduvai in the Tuff IIB zone or earliest Middle Augitic Sandstone. A major disconformity between Sequences 3 and 4 at and near EF-HR cuts through the level of Tuff IIC, placing the main Acheulean EF-HR assemblage at the base of Sequence 4, within Upper rather than Middle Bed II. Sequence stratigraphic methods also yield a more highly resolved Bed II stratigraphic framework. Backwall and sidewall surveying of archaeological trenches at EF-HR and HWK EE permits definition of "Lake-parasequences" nested within the major Sequences that record downcutting of disconformities associated with lake regression, then

  16. Fast evolving conduits in clay-bonded sandstone: Characterization, erosion processes and significance for the origin of sandstone landforms

    NASA Astrophysics Data System (ADS)

    Bruthans, Jiri; Svetlik, Daniel; Soukup, Jan; Schweigstillova, Jana; Valek, Jan; Sedlackova, Marketa; Mayo, Alan L.

    2012-12-01

    In Strelec Quarry, the Czech Republic, an underground conduit network > 300 m long with a volume of ~ 104 m3 and a catchment of 7 km2 developed over 5 years by groundwater flow in Cretaceous marine quartz sandstone. Similar landforms at natural exposures (conduits, slot canyons, undercuts) are stabilized by case hardening and have stopped evolving. The quarry offers a unique opportunity to study conduit evolution in sandstone at local to regional scales, from the initial stage to maturity, and to characterize the erosion processes which may form natural landforms prior to stabilization. A new technique was developed to distinguish erodible and non-erodible sandstone surfaces. Based on measurements of relative erodibility, drilling resistance, ambient and water-saturated tensile strength (TS) at natural and quarry exposures three distinct kinds of surfaces were found. 1) Erodible sandstone exposed at ~ 60% of surfaces in quarry. This sandstone loses as much as 99% of TS when saturated. 2) Sub-vertical fracture surfaces that are non-erodible already prior to exposure at ground surface and which keep considerable TS if saturated. 3) Case hardened surfaces that start to form after exposure. In favorable conditions they became non-erodible and reach the full TS in just 6 years. An increase in the hydraulic gradient from ~ 0.005 to > 0.02 triggered conduit evolution, based on long-term monitoring of water table in 18 wells and inflows to the quarry. Rapidly evolving major conduits are characterized by a channel gradient of ~ 0.01, a flow velocity ~ 40 cm/s and sediment concentration ~ 10 g/l. Flow in openings with a discharge 1 ml/s and hydraulic gradient > 0.05 exceeds the erosion threshold and initiates piping. In the first phase of conduit evolution, fast concentrated flow mobilizes erodible sandstone between sets of parallel fractures in the shallow phreatic zone. In the second phase the conduit opening mainly expands vertically upward into the vadose zone by mass

  17. A review of the multiwell experiment in tight gas sandstones of the Mesaverde Group, Piceance Basin, Colorado

    USGS Publications Warehouse

    Nelson, P.H.

    2002-01-01

    The Cretaceous Iles and Williams Fork Formations of the Mesaverde Group contain important reservoir and source rocks for basin-centered gas accumulations in the Piceance Basin of northwestern Colorado. The sandstones in these formations have very low permeability, so low that successful production of gas requires the presence of fractures. To increase gas production, the natural fracture system of these "tight gas sandstones" must be augmented by inducing artificial fractures, while minimizing the amount of formation damage due to introduced fluids. The Multiwell Experiment was undertaken to provide geological characterization, obtain physical property data, and perform stimulation experiments in the Iles and Williams Fork Formations. Three vertical wells and one follow-up slant well were drilled, logged, partially cored, tested for gas production, stimulated in various manners, and tested again. Drawing from published reports and papers, this review paper presents well log, core, and test data from the Multiwell Experiment while emphasizing the geological controls on gas production at the site. Gas production is controlled primarily by a set of regional fractures trending west-northwest. The fractures are vertical, terminating at lithologic boundaries within and at the upper and lower boundaries of sandstone beds. Fractures formed preferentially in sandstones where in situ stress and fracture gradients are lower than in shales and mudstones. The fractures cannot be identified adequately in vertical wellbores; horizontal wells are required. Because present-day maximum horizontal stress is aligned with the regional fractures, artificial fractures induced by pressuring the wellbore form parallel to the regional fractures rather than linking them, with consequent limitations upon enhancement of gas production.

  18. Deformation of Aztec Sandstone at Valley of Fire of Nevada: failure modes, sequence of deformation, structural products and their interplay with paleo fluids

    NASA Astrophysics Data System (ADS)

    Aydin, A.

    2014-12-01

    The Valley of Fire State Park, 60 km NE of Las Vegas, is a beacon of knowledge for deformation of Aztec Sandstone, a cross-bedded quartz arenite deposited in the Aztec-Navajo-Nugget erg in early Jurassic. It displays great diversity of physical properties, different localization types and micromechanics. The two deformation episodes, the Sevier folding & thrusting and the Basin & Range extension affected the area. The appearance of compaction bands marks the earliest deformation structure and their distribution, orientation, and dimension are controlled by the depositional architecture and loading. The earliest shear structures in the area are the Muddy Mountain, Summit, and Willow Tank thrusts and numerous small-scale bed-parallel faults. They altogether produced several kilometers of E-SE transport and shortening in the late Cretaceous and display numerous shear bands in its damage zone within the Aztec Sandstone. Shear bands also occur along dune boundaries and cross-bed interfaces. These observations indicate that the early deformation of the sandstone was accommodated by strain localization with various kinematics. The younger generation of faults in the area is of mid-Miocene age, and crops out pervasively. It includes a series of small offset normal faults (less than a few ten meters) which can be identified at steep cliff faces. These faults are highly segmented and are surrounded by a dense population of splay fractures. A large number of these splays were later sheared sequentially resulting in a well-defined network of left- and right-lateral strike-slip faults with slip magnitudes up to a few kilometers in the Park. The formation mechanisms of both the normal and strike-slip faults can be characterized as the sliding along planes of initial weaknesses and the accompanying cataclastic deformation. Some of the initial weak planes are associated with the depositional elements such as interdune boundaries and cross-bed interfaces while others are joint

  19. Downslope coarsening in aeolian grainflows of the Navajo Sandstone

    NASA Astrophysics Data System (ADS)

    Loope, David B.; Elder, James F.; Sweeney, Mark R.

    2012-07-01

    Downslope coarsening in grainflows has been observed on present-day dunes and generated in labs, but few previous studies have examined vertical sorting in ancient aeolian grainflows. We studied the grainflow strata of the Jurassic Navajo Sandstone in the southern Utah portion of its outcrop belt from Zion National Park (west) to Coyote Buttes and The Dive (east). At each study site, thick sets of grainflow-dominated cross-strata that were deposited by large transverse dunes comprise the bulk of the Navajo Sandstone. We studied three stratigraphic columns, one per site, composed almost exclusively of aeolian cross-strata. For each column, samples were obtained from one grainflow stratum in each consecutive set of the column, for a total of 139 samples from thirty-two sets of cross-strata. To investigate grading perpendicular to bedding within individual grainflows, we collected fourteen samples from four superimposed grainflow strata at The Dive. Samples were analyzed with a Malvern Mastersizer 2000 laser diffraction particle analyser. The median grain size of grainflow samples ranges from fine sand (164 μm) to coarse sand (617 μm). Using Folk and Ward criteria, samples are well-sorted to moderately-well-sorted. All but one of the twenty-eight sets showed at least slight downslope coarsening, but in general, downslope coarsening was not as well-developed or as consistent as that reported in laboratory subaqueous grainflows. Because coarse sand should be quickly sequestered within preserved cross-strata when bedforms climb, grain-size studies may help to test hypotheses for the stacking of sets of cross-strata.

  20. New geochronologic and stratigraphic evidence confirms the paleocene age of the dinosaur-bearing ojo alamo sandstone and animas formation in the San Juan Basin, New Mexico and Colorado

    USGS Publications Warehouse

    Fassett, J.E.

    2009-01-01

    Dinosaur fossils are present in the Paleocene Ojo Alamo Sandstone and Animas Formation in the San Juan Basin, New Mexico, and Colorado. Evidence for the Paleo-cene age of the Ojo Alamo Sandstone includes palynologic and paleomagnetic data. Palynologic data indicate that the entire Ojo Alamo Sandstone, including the lower dinosaur-bearing part, is Paleocene in age. All of the palynomorph-productive rock samples collected from the Ojo Alamo Sandstone at multiple localities lacked Creta-ceous index palynomorphs (except for rare, reworked specimens) and produced Paleocene index palynomorphs. Paleocene palynomorphs have been identified strati-graphically below dinosaur fossils at two separate localities in the Ojo Alamo Sand-stone in the central and southern parts of the basin. The Animas Formation in the Colorado part of the basin also contains dinosaur fossils, and its Paleocene age has been established based on fossil leaves and palynology. Magnetostratigraphy provides independent evidence for the Paleocene age of the Ojo Alamo Sandstone and its dinosaur-bearing beds. Normal-polarity magnetochron C29n (early Paleocene) has been identified in the Ojo Alamo Sandstone at six localities in the southern part of the San Juan Basin. An assemblage of 34 skeletal elements from a single hadrosaur, found in the Ojo Alamo Sandstone in the southern San Juan Basin, provided conclusive evidence that this assemblage could not have been reworked from underlying Cretaceous strata. In addition, geochemical studies of 15 vertebrate bones from the Paleocene Ojo Alamo Sandstone and 15 bone samples from the underlying Kirtland Formation of Late Creta-ceous (Campanian) age show that each sample suite contained distinctly different abundances of uranium and rare-earth elements, indicating that the bones were miner-alized in place soon after burial, and that none of the Paleocene dinosaur bones ana-lyzed had been reworked. ?? U.S. Geological Survey, Public Domain April 2009.

  1. Provenance of sandstones in the Golconda terrane, north central Nevada

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jones, E.A.

    1991-02-01

    The upper Paleozoic Golconda terrane of north-central Nevada is a composite of several structurally bounded subterranes made of clastic, volcanic, and carbonate rocks. The clastic rocks provide important clues for the interpretation of the provenance and paleogeographic settings of the different lithologic assemblages found in these subterranes. Two petrographically distinct sandstones are identified in the Golconda terrane in the Osgood Mountains and the Hot springs Range of north-central Nevada. The sandstone of the Mississippian Farrel Canyon Formation, part of the Dry Hills subterrane, is characterized by quartzose and sedimentary and lithic-rich clasts with a small feldspar component. in contrast, themore » sandstone of the Permian Poverty Peak (II) subterrane is a silty quartzarenite with no lithic component, and a very limited feldspar component. The sandstone of the Farrel Canyon Formation is similar to nonvolcanic sandstones reported from elsewhere in the Golconda terrane. Modal data reflect a provenance of a recycled orogen and permit the interpretation that it could have been derived from the antler orogen as has been proposed for other sandstones of the golconda terrane. The sandstone of the Poverty Peak (II) subterrane is more mature than any of the other sandstones in either the Golconda terrane, the Antler overlap sequence, or the Antler foreland basin sequence. Modal data put the Poverty Peak (II) sandstone in the continental block provenance category. The distinct extrabasinal provenances represented in these different sandstones support the idea that the Golconda basin was made up of complex paleogeographic settings, which included multiple sources of extrabasinal sediment.« less

  2. Failure warning of hydrous sandstone based on electroencephalogram technique

    NASA Astrophysics Data System (ADS)

    Tao, Kai; Zheng, Wei

    2018-06-01

    Sandstone is a type of rock mass that widely exists in nature. Moisture is an important factor that leads to sandstone structural failure. The major failure assessment methods of hydrous sandstone at present cannot satisfy real-time and portability requirements, especially lacks of warning function. In this study, acoustic emission (AE) and computed tomography (CT) techniques are combined for real-time failure assessment of hydrous sandstone. Eight visual colors for warning are screened according to different failure states, and an electroencephalogram (EEG) experiment is conducted to demonstrate their diverse excitations of the human brain's concentration.

  3. Permeability and permeability anisotropy in Crab Orchard sandstone: Experimental insights into spatio-temporal effects

    NASA Astrophysics Data System (ADS)

    Gehne, Stephan; Benson, Philip M.

    2017-08-01

    Permeability in tight crustal rocks is primarily controlled by the connected porosity, shape and orientation of microcracks, the preferred orientation of cross-bedding, and sedimentary features such as layering. This leads to a significant permeability anisotropy. Less well studied, however, are the effects of time and stress recovery on the evolution of the permeability hysteresis which is becoming increasingly important in areas ranging from fluid migration in ore-forming processes to enhanced resource extraction. Here, we report new data simulating spatio-temporal permeability changes induced using effective pressure, simulating burial depth, on a tight sandstone (Crab Orchard). We find an initially (measured at 5 MPa) anisotropy of 2.5% in P-wave velocity and 180% in permeability anisotropy is significantly affected by the direction of the effective pressure change and cyclicity; anisotropy values decrease to 1% and 10% respectively after 3 cycles to 90 MPa and back. Furthermore, we measure a steadily increasing recovery time (10-20 min) for flow parallel to cross-bedding, and a far slower recovery time (20-50 min) for flow normal to cross-bedding. These data are interpreted via strain anisotropy and accommodation models, similar to the "seasoning" process often used in dynamic reservoir extraction.

  4. Shoreface to estuarine sedimentation in the late Paleocene Matanomadh Formation, Kachchh, western India

    NASA Astrophysics Data System (ADS)

    Srivastava, V. K.; Singh, B. P.

    2017-04-01

    Late Paleocene sedimentation in the pericratonic Kachchh Basin marks the initial marine transgression during the Cenozoic era. A 17 m thick sandstone-dominated succession, known as the clastic member (CM) of the Matanomadh Formation (MF), is exposed sporadically in the basin. Three facies associations are reconstructed in the succession in three different sections. Facies association-1 contains matrix-supported pebbly conglomerate facies, horizontally-laminated sandstone-mudstone alternation facies, hummocky- and swaley cross-bedded sandstone facies, wave-rippled sandstone facies and climbing ripple cross-laminated sandstone facies. This facies association developed between shoreface and foreshore zone under the influence of storms on a barrier ridge. Facies association-2 contains sigmoidal cross-bedded sandstone facies, sandstone-mudstone alternation facies, flaser-bedded sandstone facies, herringbone cross-bedded sandstone facies and tangential cross-bedded sandstone facies. This facies association possessing tidal bundles and herringbone cross-beds developed on a tidal flat with strong tidal influence. Facies association-3 comprises pebbly sandstone facies, horizontally-bedded sandstone facies, tangential cross-bedded sandstone facies exhibiting reactivation surfaces and tabular cross-bedded sandstone facies. This facies association represents sedimentation in a river-dominated estuary and reactivation surfaces and herringbone cross-beds indicating tidal influence. The bipolar paleocurrent pattern changes to unipolar up-section because of the change in the depositional currents from tidal to fluvial. The sedimentation took place in an open coast similar to the Korean coast. The presence of neap-spring tidal rhythmites further suggests that a semidiurnal system similar to the modern day Indian Ocean was responsible for the sedimentation. Here, the overall sequence developed during the transgressive phase where barrier ridge succession is succeeded by the tidal

  5. The depositional environment and petrology of the White Rim Sandstone Member of the Permian Cutler Formation, Canyonlands National Park, Utah

    USGS Publications Warehouse

    Steele-Mallory, B. A.

    1982-01-01

    The White Rim Sandstone Member of the Cutler Formation of Permian age in Canyonlands National Park, Utah, was deposited in coastal eolian and associated interdune environments. This conclusion is based on stratigraphic relationships primary sedimentary structures, and petrologic features. The White Rim consists of two major genetic units. The first represents a coastal dune field and the second represents related interdune ponds. Distinctive sedimentary structures of the coastal dune unit include large- to medium-scale, unidirectional, tabular-planar cross-bedding; high-index ripples oriented parallel to dip direction of the foresets; coarse-grained lag layers; avalanche or slump marks; and raindrop impressions. Cross-bedding measurements suggest the dunes were deposited as transverse ridges by a dominantly northwest to southeast wind. Distinctive sedimentary structures of the interdune pond unit include wavy, horizontally laminated bedding, adhesion ripples, and desiccation polygons. These features may have been produced by alternate wetting and drying of sediment during water-table fluctuations. Evidence of bioturbation is also present in this unit. Petrologic characteristics of the White Rim helped to define the depositional environment as coastal. A crinoid fragment was identified at one location; both units are enriched in heavy minerals, and small amounts of well rounded, reworked glauconite were found in the White Rim throughout the study area. Earlier work indicates that the White Rim sandstone is late Wolfcampian to early Leonardian in age. During this time, the Canyonlands area was located in a depositional area alternately dominated by marine and nonmarine environments. Results of this study suggest the White Rim represents a coastal dune field that was deposited by predominantly on-shore winds during a period of marine transgression.

  6. Facies identification based on conventional core-log integration: Middle Ordovician St. Peter sandstone, Michigan basin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wieczorek, L.M.; Barnes, D.A.

    1989-08-01

    Lithofacies comprising the massive sand in the Michigan basin are very similar to the lithofacies of the St. Peter Sandstone in parts of the adjacent Midwestern basin and arches region. Lithostratigraphic and biostratigraphic correlations justify application of the name St. Peter Sandstone to the gas-productive massive sand in the Michigan basin. Four lithofacies have been determined by core-log integration. The two lowermost lithofacies (1 and 2) were deposited in marginal-marine peritidal shoreface to sand-flat environments. Lithofacies 1A comprises cross-bedded, quartz-cemented quartzarenites. Lithofacies 1B comprises dolomitic, cross-bedded, subfeldspathic arenites. Lithofacies 1A is recognized in logs by low gamma-ray response (less thanmore » 20-25 API units) and photoelectric effect (Pe) of 1.8. Lithofacies 1B log characteristics include low gamma ray response (15-30 API units) and Pe of 2-2.5. Lithofacies 2 log signatures include moderate to high gamma-ray (30-120 API units) and Pe values that range from 2.5-3.5. The uppermost two lithofacies (3 and 4) were deposited in storm-dominated lower shoreface, to offshore, to distal marine shelf environments. Lithofacies 3 consists of burrowed, massive, wavy to planar stratified quartzarenites to subfeldspathic arenites. Log signature is generally low gamma-ray response (15-30 API units) and Pe that ranges from 1.8 to 2.5. Lithofacies 4 consists of massive, burrowed and bioturbated, dominantly authigenic clay and dolomite-cemented subfeldspathic arenite. Lithofacies 4 log response is moderate to high gamma-ray response (30-105 API units) and Pe ranging from 2.25 to 3.5.« less

  7. Detrital zircon provenance of the Hartselle Sandstone Unit, Southeastern USA: Insights into sediment source, paleogeography, and setting

    NASA Astrophysics Data System (ADS)

    Harthy, M. A.; Gifford, J.

    2017-12-01

    The Hartselle sandstone is an excellent example of an Oil sand, a resource rich in bitumen. The unit is a light-colored thick-bedded to massive quartzose sandstone, that is widespread across an area from Georgia in the east to Mississippi in the west, and south from Alabama to Kentucky as a northern border. Formation thickness ranges from 0 to more than 150 feet. The unit has been stratigraphically dated to the Middle-Upper Mississippian age. One hypothesis suggests that the sandstone unit formed from the geological remains of barrier islands located in the ocean between Gondwana and Laurentia. The Hartselle is thought to have formed by the movement waves and currents along the shoreline, which carried sand and concentrated it into a set of northwest to southeast trending barrier islands. Transgression-regression events shifted the islands back and forth in relation to the position of the shoreline, leading to the large areal extent of the unit. However, the current data are not enough to explain the geographical position of the Hartselle sandstone unit as it is not running parallel to the ancient shoreline. Another mystery is the source of the sand, some believing the source was from the south (Gondwana) and others that erosion was from the north (Laurentia). Detrital zircon provenance analysis will address the uncertainty in sediment source. We will compare zircon U-Pb age spectra to possible Laurentian and Gondwanan source areas to discriminate between these possibilities. In addition, the age of the youngest detrital zircon population will provide additional constraints on the maximum age of deposition for the unit. These detrital ages will also help us to understand the tectonic setting at the time of Hartselle deposition. Lastly, we aim to explain the widespread nature of the unit and the processes involved in the formation of the Hartselle sandstone. When taken together, these interpretations will illuminate the age, depositional and tectonic setting of a

  8. Unaltered cosmic spherules in a 1.4-Gyr-old sandstone from Finland.

    PubMed

    Deutsch, A; Greshake, A; Pesonen, L J; Pihlaja, P

    1998-09-10

    Micrometeorites-submillimetre-sized particles derived from asteroids and comets-occur in significant quantities in deep sea sediments, and the ice sheets of Greenland and Antarctica. The most abundant micrometeorites are cosmic spherules, which contain nickel-rich spinels that were crystallized and oxidized during atmospheric entry, therefore recording the oxygen content in the uppermost atmosphere. But the use of micrometeorites for detecting past changes in the flux of incoming extraterrestrial matter, and as probes of the evolution of the atmosphere, has been hampered by the fact that most objects with depositional ages higher than 0.5 Myr show severe chemical alteration. Here we report the discovery of unaltered cosmic spherules in a 1.4-Gyr-old sandstone (red bed) from Finland. From this we infer that red beds, a common lithology in the Earth's history, may contain substantial unbiased populations of fossil micrometeorites. The study of such populations would allow systematic research on variations in the micrometeorite flux from the early Proterozoic era to recent times (a time span of about 2.5 Gyr), and could help to better constrain the time when the atmospheric oxygen content was raised to its present level.

  9. Quantitative petrographic analysis of Desmoinesian sandstones from Oklahoma

    USGS Publications Warehouse

    Dyman, Thaddeus S.

    1989-01-01

    Desmoinesian sandstones from the northern Oklahoma platform and the Anadarko, Arkoma, and Ardmore basins record a complex interaction between mid-Pennsylvanian source-area tectonism and cyclic sedimentation patterns associated with numerous transgressions and regressions. Framework-grain summaries for 50 thin sections from sandstones of the Krebs, Cabaniss, and Marmaton Groups and their surface and subsurface equivalents were subjected to multivariate statistical analyses to establish regional compositional trends for provenance analysis. R-mode cluster and correspondence analyses were used to determine the contributing effect (total variance) of key framework grains. Fragments of monocrystalline and polycrystalline quartz; potassium and plagioclase feldspar; chert; and metamorphic, limestone, and mudstone-sandstone rock fragments contribute most to the variation in the grain population. Q-mode cluster and correspondence analyses were used to identify four petrofacies and establish the range of compositional variation in Desmoinesian sandstones. Petrofacies I is rich in monocrystalline quartz (78-98%); mica and rock fragments are rare. Petrofacies II is also rich in monocrystalline quartz (60-84%) and averages 12% total rock fragments. Petrofacies III and IV are compositionally heterogeneous and contain variable percentages of monocrystalline and polycrystalline quartz, potassium feldspar, mica, chert, and metamorphic and sedimentary rock fragments. Quantitative analyses indicate that Desmoinesian sandstones were derived from sedimentary, igneous, and metamorphic source areas. Sandstones of petrofacies I and II occur mostly in the lower Desmoinesian and are widely distributed, although they are most abundant in eastern and central Oklahoma; sandstones of petrofacies III and IV are widely distributed and occur primarily in the middle and upper Desmoinesian. The range of compositional variation and the distribution of petrofacies are related to paleotectonics and

  10. The sandstone's chromatic alteration of the florentine cultural heritage

    NASA Astrophysics Data System (ADS)

    Vettori, S.; Pecchioni, E.; Cantisani, E.; Ricci, M.; Fratini, F.; Garzonio, C. A.

    2012-04-01

    Pietra Serena is one of the materials more used in Florentine architecture. It is a sandstone that outcrops in the hills north of the city in the municipality of Fiesole and it has been employed mainly for ornamental purposes. This litotype belongs to the the Macigno Formation (Oligocene Upper- Miocene Lower) which consists of beds of turbiditic sandstones separated by pelitic levels which are the finest components of each single turbidity layer. Petrographically, Pietra Serena can be defined as a medium-coarse-grained greywacke made of quartz, feldspars, micas, fragments of metamorphic and magmatic rocks. The clayey matrix is quite abundant, mainly composed by illite, kaolinite and chlorite-vermiculite (present only in some quarries). It is well known that the processes of decay of the sandstones are related to the type of matrix, the amount of cement, the kind of clay minerals and to the pore size distribution, which lead to water infiltrations, swelling of the clay minerals, separation of the clayey matrix, with resulting exfoliation and peeling of the stone artefacts. Pietra Serena has a bluish-grey colour in fresh cut, but many times it is easily oxidized acquiring an ochraceous-reddish brown colour on buildings. Such changes in colour, appear to be due in part to the oxidation of iron, proceeding very quickly from the surface to the inside, though the cohesion is not affected. It is possible to hypothesize that the chromatic changes not necessarily involve a progressive state of alteration of the artefact, but they may often to represents a natural patina acquired with the time. Nevertheless it is necessary to remember that the oxidized layer and its hardness could also be the result of treatments performed in the past. In Florence, several monuments and buildings are affected by such phenomenon, in particular it is possible to note an intense and diffuse reddish colouring on the Pietra Serena utilized for columns and for façade's decorations. In this work

  11. Experimental study on the CO2-flow mechanism in the two different sandstones

    NASA Astrophysics Data System (ADS)

    Imasato, M.; Honda, H.; Kitamura, K.

    2016-12-01

    It is important to discuss the flow properties of CO2 in the reservoir for estimations of storage potential and safety of CCS operation. In this study, we conducted the CO2-injection tests into two different types of porous sandstones with extremely low CO2 flow rate (10µl/min) under supercritical CO2 conditions. It was measured CO2 saturation (SCO2) and differential pressure (ΔP) between upstream and downstream of specimen. It was also monitored P-wave velocity (Vp) and electrical impedance (Z) for the monitoring of CO2 behavior in the specimen. We set three Vp measurement lines in different height for monitoring the movement of CO2 front. The results of ΔP measurement indicated that the Berea sandstone showed no obvious change, but the Ainoura sandstone was increasing gradually and peaked in 73 hours. After that, ΔP of the Ainoura sandstone started reducing. Both sandstones showed stepwise Vp-reduction from the bottom Vp-measurement line, which is near CO2 injection end. There are large differences of CO2 arrival time at the bottom line between Berea and Ainoura sandstone. In case of Ainoura sandstone, it took 29 hours to reduce Vp which is the nearest to CO2 injection end, but in case of Berea sandstone, it took 3.3 hours. This is also confirmed the arrival time at the top channel, 2.5 hours in the Berea sandstone and 11 hours in the Ainoura sandstone. The impedances of both sandstones indicted the gradual increment. It took 25 hours to become constant in the Berea sandstone and 148 hours in the Ainoura sandstone. SCO2 of the Berea sandstone was about 6% and Ainoura sandstone reached over 20%. These results suggest that it is due to the difference of the pore structure of Berea sandstone and Ainoura sandstone.

  12. Pressure sensitivity of low permeability sandstones

    USGS Publications Warehouse

    Kilmer, N.H.; Morrow, N.R.; Pitman, Janet K.

    1987-01-01

    Detailed core analysis has been carried out on 32 tight sandstones with permeabilities ranging over four orders of magnitude (0.0002 to 4.8 mD at 5000 psi confining pressure). Relationships between gas permeability and net confining pressure were measured for cycles of loading and unloading. For some samples, permeabilities were measured both along and across bedding planes. Large variations in stress sensitivity of permeability were observed from one sample to another. The ratio of permeability at a nominal confining pressure of 500 psi to that at 5000 psi was used to define a stress sensitivity ratio. For a given sample, confining pressure vs permeability followed a linear log-log relationship, the slope of which provided an index of pressure sensitivity. This index, as obtained for first unloading data, was used in testing relationships between stress sensitivity and other measured rock properties. Pressure sensitivity tended to increase with increase in carbonate content and depth, and with decrease in porosity, permeability and sodium feldspar. However, scatter in these relationships increased as permeability decreased. Tests for correlations between pressure sensitivity and various linear combinations of variables are reported. Details of pore structure related to diagenetic changes appears to be of much greater significance to pressure sensitivity than mineral composition. ?? 1987.

  13. Origin of a classic cratonic sheet sandstone: Stratigraphy across the Sauk II-Sauk III boundary in the Upper Mississippi Valley

    USGS Publications Warehouse

    Runkel, Anthony C.; McKay, R.M.; Palmer, A.R.

    1998-01-01

    The origin of cratonic sheet sandstones of Proterozoic and early Paleozoic age has been a long-standing problem for sedimentologists. Lower Paleozoic strata in the Upper Mississippi Valley are best known for several such sandstone bodies, the regional depositional histories of which are poorly understood. We have combined outcrop and subsurface data from six states to place the Upper Cambrian Wonewoc (Ironton and Galesville) Sandstone in a well-constrained stratigraphic framework across thousands of square kilometers. This framework makes it possible for the first time to construct a regional-scale depositional model that explains the origin of this and other cratonic sheet sandstones. The Wonewoc Sandstone, although mapped as a single contiguous sheet, is a stratigraphically complex unit that was deposited during three distinct conditions of relative sea level that span parts of four trilobite zones. During a relative highstand of sea level in Crepicephalus Zone time, quartzose sandstone lithofacies aggraded more or less vertically in nearshore-marine and terrestrial environments across much of the present-day out-crop belt around the Wisconsin arch. At the same time, finer grained, feldspathic sandstone, siltstone, and shale aggraded in deeper water immediately seaward of the quartzose sand, and shale and carbonate sediment accumulated in the most distal areas. During Aphelaspis and Dunderbergia Zones time a relative fall in sea level led to the dispersal of quartzose sand into a basinward-tapering, sheet-like body across much of the Upper Mississippi Valley. During early Elvinia Zone time a major transgression led to deposition of a second sheet sandstone that is generally similar to the underlying regressive sheet. The results of this investigation also demonstrate how subtle sequence-bounding unconformities may be recognized in mature, cratonic siliciclastics. We place the Sauk II-Sauk III subsequence boundary at the base of the coarsest bed in the Wonewoc

  14. Sensing, Measuring and Modelling the Mechanical Properties of Sandstone

    NASA Astrophysics Data System (ADS)

    Antony, S. J.; Olugbenga, A.; Ozerkan, N. G.

    2018-02-01

    We present a hybrid framework for simulating the strength and dilation characteristics of sandstone. Where possible, the grain-scale properties of sandstone are evaluated experimentally in detail. Also, using photo-stress analysis, we sense the deviator stress (/strain) distribution at the micro-scale and its components along the orthogonal directions on the surface of a V-notch sandstone sample under mechanical loading. Based on this measurement and applying a grain-scale model, the optical anisotropy index K 0 is inferred at the grain scale. This correlated well with the grain contact stiffness ratio K evaluated using ultrasound sensors independently. Thereafter, in addition to other experimentally characterised structural and grain-scale properties of sandstone, K is fed as an input into the discrete element modelling of fracture strength and dilation of the sandstone samples. Physical bulk-scale experiments are also conducted to evaluate the load-displacement relation, dilation and bulk fracture strength characteristics of sandstone samples under compression and shear. A good level of agreement is obtained between the results of the simulations and experiments. The current generic framework could be applied to understand the internal and bulk mechanical properties of such complex opaque and heterogeneous materials more realistically in future.

  15. Elevated Uranium in Aquifers of the Jacobsville Sandstone

    NASA Astrophysics Data System (ADS)

    Sherman, H.; Gierke, J.

    2003-12-01

    The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of

  16. Provenance and petrofacies, Upper Devonian sandstones, Philip Smith Mountains and Arctic quandrangles, Brooks Range, Alaska: Final report, Project No. 3

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Anderson, A.V.; Coney, P.J.

    1987-11-01

    Late Devonian sandstone beds are exposed as allochthonous sequences that extend for over 1000 km along the east-west strike of the Brooks Range in northern Alaska. These horizons, at least in part, record Late Devonian tectonism and deposition along the southern margin of the Arctic Alaska block. This study identifies clastic petrofacies in the western Philip Smith Mountains and southern Arctic quadrangles and infers the composition of the source terrane. The paleogeography is not known and the original distribution of lithofacies is uncertain, owing to the extensive post-depositional tectonism. In the study area the sandstones are exposed along rugged mountainmore » tops and high ridges. Although exposures are excellent, access is often difficult. Samples were collected from exposures near the western end of the Chandalar Shelf, Atigun Pass, and the Atigun River valley in the Philip Smith Mountains quadrangle and from the Crow Nest Creek and Ottertail Creek areas in the Arctic quadrangle. 34 refs., 17 figs.« less

  17. Transport of silver nanoparticles in single fractured sandstone

    NASA Astrophysics Data System (ADS)

    Neukum, Christoph

    2018-02-01

    Silver nanoparticles (Ag-NP) are used in various consumer products and are one of the most prevalent metallic nanoparticle in commodities and are released into the environment. Transport behavior of Ag-NP in groundwater is one important aspect for the assessment of environmental impact and protection of drinking water resources in particular. Ag-NP transport processes in saturated single-fractured sandstones using triaxial flow cell experiments with different kind of sandstones is investigated. Ag-NP concentration and size are analyzed using flow field-flow fractionation and coupled SEM-EDX analysis. Results indicate that Ag-NP are more mobile and show generally lower attachment on rock surface compared to experiments in undisturbed sandstone matrix and partially fractured sandstones. Ag-NP transport is controlled by the characteristics of matrix porosity, time depending blocking of attachment sites and solute chemistry. Where Ag-NP attachment occur, it is heterogeneously distributed on the fracture surface.

  18. Distal alluvial fan sediments in early Proterozoic red beds of the Wilgerivier formation, Waterberg Group, South Africa

    NASA Astrophysics Data System (ADS)

    Van Der Neut, M.; Eriksson, P. G.; Callaghan, C. C.

    The 1900 - 1700 M.a. Waterberg Group belongs to a series of southern African cratonic cover sequences of roughly equivalent age. Red beds of the Wilgerivier Formation comprise sandstones, interbedded with subordinate conglomerates and minor mudrocks. These immature sedimentary rocks exhibit lenticular bedding, radial palaeocurrent patterns and features indicative of both streamflow and gravity-flow deposition. A distal wet alluvial fan palaeoenvironmental setting is envisaged, with fan-deltas forming where alluvial lobes prograded into a lacustrine basin. Intrastratal, diagenetic alteration of ferromagnesian detrital grains and ferruginous grain coatings led to the red colouration of the Wilgerivier sediments.

  19. Stratigraphic comparison of six oil fields (WV) producing from Big Injun sandstones

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zou, X.; Donaldson, A.C.

    1993-08-01

    Clustered within western West Virginia, six oil fields produce from the lower Mississippian Big Injun sandstones, and three more oil fields also supplement this production either from underlying Squaw or Weir sandstones. Shales separate these sandstones that occur stratigraphically between the Sunbury Shale (maximum flooding surface) and pre-Greenbrier unconformity (maximum regressive erosional surface), and represent highstand regressive deposits associated with the postorogenic phase of foreland basin accumulation. Stratigraphic studies show two Big Injun sandstones. The upper sandstone, called the Maccrady Big Injun, is separated from the lower Price/Pocono Big Injun sandstone by red shales. Both Big Injun sandstones consist ofmore » fine-grained river-mouth bars capped by coarse-grained river-channel deposits. Although the six fields are within three adjacent counties, Maccrady Big Injun sandstones of Blue Creek (Kanawha) and Rock Creek (Roane) fields are younger and were deposited by a different fluvial-deltaic system than the Price/Pocono Big Injun sandstones of Granny Creek (Clay), Tariff (Roane) Clendenin (Clay), and Pond Fork (Kanawha) fields. Upper Weir sandstones are thick, narrow north-trending belts underlying Pond Fork and Blue Creek fields, with properties suggesting wave-dominated shoreline deposits. Allocycles spanning separate drainage systems indicate eustasy. Postorogenic flexural adjustments probably explain stacked sandstone belts with superposed paleovalleys of overlying unconformities (pre-Greenbrier, Pottsville), particularly where aligned along or parallel basement structures of Rome trough or West Virginia dome. Initially, differential subsidence or uplift during sedimentation influenced the position, geometry, trend, and distribution patterns of these reservoir sandstone, then influenced their preserved condition during erosion of pre-Greenbrier unconformity.« less

  20. The Transfiguration continental red-bed Cu-Pb-Zn-Ag deposit, Quebec Appalachians, Canada

    NASA Astrophysics Data System (ADS)

    Cabral, Alexandre Raphael; Beaudoin, Georges; Taylor, Bruce E.

    2009-04-01

    The Transfiguration Cu-Pb-Zn-Ag deposit, enclosed within reduced grey sandstone, is associated with continental red beds of the Lower Silurian Robitaille Formation in the Quebec Appalachians, Canada. The Robitaille Formation rests unconformably on foliated Cambro-Ordovician rocks. The unconformity is locally cut by barite veins. The basal unit of the Robitaille Formation comprises green wacke and pebble conglomerate, which locally contain calcite nodules. The latter have microstructures characteristic of alpha-type calcretes, such as “floating” fabrics, calcite-filled fractures (crystallaria) and circumgranular cracks. Massive, grey sandstone overlies the basal green wacke and pebble conglomerate unit, which is overlain, in turn, by red, fine-grained sandstone. Mineralisation occurred underneath the red sandstone unit, chiefly in the grey sandstone unit, as disseminated and veinlet sulphides. Chalcopyrite, the most abundant Cu sulphide, replaced early pyrite. Calcrete, disseminated carbonate and vein carbonate have stable isotope ratios varying from -7.5‰ to -1.1‰ δ13C and from 14.7‰ to 21.3‰ δ18O. The negative δ13C values indicate the oxidation of organic matter in a continental environment. Sulphur isotope ratios for pyrite, chalcopyrite and galena vary from -19‰ to 25‰ δ34S, as measured on mineral concentrates by a conventional SO2 technique. Laser-assisted microanalyses (by fluorination) of S isotopes in pyrite show an analogous range in δ34S values, from -21‰ to 25‰. Negative and positive δ34S values are compatible with bacterial sulphate reduction (BSR) in systems open and closed with respect to sulphate. We interpret similarly high δ34S values for sulphide concentrates (25.1‰) and for vein barite (26.2‰) to result from rapid and complete thermochemical reduction of pore-water sulphate. Two early to late diagenetic stages of mineralisation best explain the origin of the Transfiguration deposit. The first stage was characterised

  1. Impacts of variable channel hydraulics on the stratigraphic record: an example provided from the Tullig Sandstone, Western Irish Namurian Basin

    NASA Astrophysics Data System (ADS)

    Wu, C.; Nittrouer, J. A.; Burmeister, K. C.

    2017-12-01

    River hydrodynamic conditions are modified where a system approaches its terminal basin, characterized by the onset of non-uniform "backwater" flow. A decrease in boundary shear stress in the backwater region reduces transport capacity and results in sediment deposition on the channel bed. Although such morphodynamic conditions are common in modern fluvial-deltaic channels, the extent to which these processes are prevalent in the stratigraphic record remains unclear. For example, a few studies documenting changes in fluvial sandstone channel dimensions and grain size distributions near a river terminus attributed this variability to backwater hydrodynamics. However, quantitative tests using morphodynamic models bolstered by a variety of field observations, which could then be linked to sediment depositional patterns and stratigraphy, have yet to be produced. Here we calibrate a one-dimensional river flow model with measurements of paleo-slope and channel depth, and use the output to constrain a sediment transport model, with data from the Tullig Sandstone in the Western Irish Namurian Basin. Based on the model results, our analyses indicate that: (1) backwater hydrodynamics influence the spatial variation of sandstone dimensions and grain size across the delta, and (2) backwater hydrodynamics drive channel bed aggradation and progradation of the river mouth for conditions of constant sea level. Field data indicate that the reach-average story thickness increases, and then decreases, progressing downstream over the backwater reach. Based on the inferred transport and depositional processes, the measured deltaic stratigraphy patterns shown here are assumed to be associated with backwater hydrodynamics, and are therefore largely autogenic in origin. These analyses indicate that non-uniform hydrodynamics can generate stratigraphic patterns that could be conflated as arising due to allogenic effects, based on traditional geometric or diffusion-based depositional models

  2. Polygonal deformation bands in sandstone

    NASA Astrophysics Data System (ADS)

    Antonellini, Marco; Nella Mollema, Pauline

    2017-04-01

    We report for the first time the occurrence of polygonal faults in sandstone, which is compelling given that layer-bound polygonal fault systems have been observed so far only in fine-grained sediments such as clay and chalk. The polygonal faults are dm-wide zones of shear deformation bands that developed under shallow burial conditions in the lower portion of the Jurassic Entrada Fm (Utah, USA). The edges of the polygons are 1 to 5 meters long. The shear deformation bands are organized as conjugate faults along each edge of the polygon and form characteristic horst-like structures. The individual deformation bands have slip magnitudes ranging from a few mm to 1.5 cm; the cumulative average slip magnitude in a zone is up to 10 cm. The deformation bands heaves, in aggregate form, accommodate a small isotropic horizontal extension (strain < 0.005). The individual shear deformation bands show abutting T-junctions, veering, curving, and merging where they mechanically interact. Crosscutting relationships are rare. The interactions of the deformation bands are similar to those of mode I opening fractures. Density inversion, that takes place where under-compacted and over-pressurized layers (Carmel Fm) lay below normally compacted sediments (Entrada Sandstone), may be an important process for polygonal deformation bands formation. The gravitational sliding and soft sediment structures typically observed within the Carmel Fm support this hypothesis. Soft sediment deformation may induce polygonal faulting in the section of the Entrada Sandstone just above the Carmel Fm. The permeability of the polygonal deformation bands is approximately 10-14 to 10-13 m2, which is less than the permeability of the host, Entrada Sandstone (range 10-12 to 10-11 m2). The documented fault networks have important implications for evaluating the geometry of km-scale polygonal fault systems in the subsurface, top seal integrity, as well as constraining paleo-tectonic stress regimes.

  3. Preliminary evaluation of the basal sandstone in Tennessee for receiving injected wastes

    USGS Publications Warehouse

    Mulderink, Dolores; Bradley, M.W.

    1986-01-01

    The EPA is authorized, under the Safe Drinking Water Act, to administer the Underground Injection Control program. This program allows for the regulation of deep-well disposal of wastes and establishes criteria to protect underground sources of drinking water from contamination. The basal sandstone in Tennessee occurs west of the Valley and Ridge province at depths of 5,000 to 9,000 ft below land surface. The basal sandstone consists of about 30 to 750 ft of Cambrian sandstone overlying the crystalline basement complex. The basal sandstone is overlain and confined by shale and carbonate rocks of the Middle and Upper Cambrian Conasauga Group. Hydrologic data for the basal sandstone, available from only three sites (four wells) in Tennessee, indicate that the basal sandstone generally has low porosity and permeability with a few zones having enough permeability to accept injected fluids. Limited water quality data indicate the basal sandstone contains water with dissolved solids concentrations exceeding 10,000 mg/L. Since the dissolved-solids concentrations exceed 10,000 mg/L, the basal sandstone is not classified as an underground source of drinking water according to EPA regulations. (Author 's abstract)

  4. Mobilization of aluminum by the acid percolates within unsaturated zone of sandstones.

    PubMed

    Navrátil, Tomáš; Vařilová, Zuzana; Rohovec, Jan

    2013-09-01

    The area of the Black Triangle has been exposed to extreme levels of acid deposition in the twentieth century. The chemical weathering of sandstones found within the Black Triangle became well-known phenomenon. Infiltration of acid rain solutions into the sandstone represents the main input of salt components into the sandstone. The infiltrated solutions--sandstone percolates--react with sandstone matrix and previously deposited materials such as salt efflorescence. Acidic sandstone percolates pH 3.2-4.8 found at ten sites within the National Park Bohemian Switzerland contained high Al-tot (0.8-10 mg L(-1)) concentrations and high concentrations of anions SO4 (5-66 mg L(-1)) and NO3 (2-42 mg L(-1)). A high proportion (50-98 %) of Al-tot concentration in acid percolates was represented by toxic reactive Al(n+). Chemical equilibrium modeling indicated as the most abundant Al species Al(3+), AlSO4 (+), and AlF(2+). The remaining 2-50 % of Al-tot concentration was present in the form of complexes with dissolved organic matter Al-org. Mobilization and transport of Al from the upper zones of sandstone causes chemical weathering and sandstone structure deterioration. The most acidic percolates contained the highest concentrations of dissolved organic material (estimated up to 42 mg L(-1)) suggesting the contribution of vegetation on sandstone weathering processes. Very low concentrations of Al-tot in springs at BSNP suggest that Al mobilized in unsaturated zone is transported deeper into the sandstone. This process of mobilization could represent a threat for the water quality small-perched aquifers.

  5. Contractional deformation of porous sandstone: Insights from the Aztec Sandstone, SE Nevada, USA

    NASA Astrophysics Data System (ADS)

    Fossen, Haakon; Zuluaga, Luisa F.; Ballas, Gregory; Soliva, Roger; Rotevatn, Atle

    2015-05-01

    Contractional deformation of highly porous sandstones is poorly explored, as compared to extensional deformation of such sedimentary rocks. In this work we explore the highly porous Aztec Sandstone in the footwall to the Muddy Mountain thrust in SE Nevada, which contains several types of deformation bands in the Buffington tectonic window: 1) Distributed centimeter-thick shear-enhanced compaction bands (SECBs) and 2) rare pure compaction bands (PCBs) in the most porous parts of the sandstone, cut by 3) thin cataclastic shear-dominated bands (CSBs) with local slip surfaces. Geometric and kinematic analysis of the SECBs, the PCBs and most of the CSBs shows that they formed during ∼E-W (∼100) shortening, consistent with thrusting related to the Cretaceous to early Paleogene Sevier orogeny of the North American Cordilleran thrust system. Based on stress path modeling, we suggest that the compactional bands (PCBs and SECBs) formed during contraction at relatively shallow burial depths, before or at early stages of emplacement of the Muddy Mountains thrust sheet. The younger cataclastic shear bands (CSBs, category 3), also related to E-W Sevier thrusting, are thinner and show larger shear offsets and thus more intense cataclasis, consistent with the initiation of cataclastic shear bands in somewhat less porous materials. Observations made in this work support earlier suggestions that contraction lead to more distributed band populations than what is commonly found in the extensional regime, and that shear-enhanced compaction bands are widespread only where porosity (and permeability) is high.

  6. The Middle Jurassic Entrada Sandstone near Gallup, New Mexico

    USGS Publications Warehouse

    Robertson, J.F.; O'Sullivan, R. B.

    2001-01-01

    Near Gallup, New Mexico, the Middle Jurassic Entrada Sandstone consists of, in ascending order, the Iyanbito Member, the Rehoboth Member, and an upper sandstone member. The Rehoboth Member is named herein to replace the middle siltstone member, with a type section located 26 km east of Gallup. The Iyanbito Member has been erroneously equated with the Wingate Sandstone of northeast Arizona, and the Rehoboth Member has been miscorrelated with the Dewey Bridge Member of the Entrada in Utah. The Dewey Bridge is an older unit that does not extend into New Mexico. The Iyanbito Member, east of Gallup, overlies the J-2 unconformity and the eroded tops of the Owl Rock and Petrified Forest Members of the Chinle Formation. The Wingate Sandstone of the Lower Jurassic Glen Canyon Group overlies the J-0 unconformity and the underlying Rock Point Member (topmost unit) of the Chinle Formation in northeast Arizona. Both the Wingate Sandstone and the Rock Point Member are missing east of Gallup below the J-2 unconformity. Similarly, the Wingate is missing southwest of Gallup, near Lupton, Arizona, but the Rock Point Member is present and underlies the Iyanbito from Zuni northward to Toadlena, New Mexico. The Wingate and other formations of the Glen Canyon Group thin and wedge out southward and eastward in northeast Arizona. The J-2 unconformity truncates the Wingate Sandstone and the underlying J-0 unconformity, 5 km north of Toadlena.

  7. The age for the fossil-bearing Tabbowa beds in Sri Lanka

    NASA Astrophysics Data System (ADS)

    Chang, S. C.; Dassanayake, S.; Wang, J.

    2014-12-01

    Well-preserved terrestrial fossils, mainly including conifers, cycads and ferns, were discovered from the Tabbowa beds in northwestern Sri Lanka. The high diversity and abundance of plants and insects from these Jurassic sediments provide a unique window to understand floral evolution and plant-insect co-evolution in the Mesozoic. For example, unearthed fossils from the Tabbowa beds indicate that leaf feeding and dwelling insects played a significant role in the Jurassic ecosystem. For another example, feeding and chewing marks on leaves allow studying insect behavior and paleo-ecology. Additionally, the recent discoveries of Otozamites latiphyllus and Otozamites tabbowensis from these sediments provide evidence that Bennettitales, an extinct order of seed plants, widely spread in the Gondwana during the Jurassic period. Although most fossils are yet to be well studied, and only few of the fossil occurrences have been published in western journals, plant fossils from the Tabbowa beds have great potential for substantially increasing our knowledge of Jurassic terrestrial ecosystems. The fossil-bearing Tabbowa beds are mainly composed of sandstone, siltstone, and mudstone with occasional thin bands of nodular limestone. Until now, radio-isotopic age determinations for the fossil-rich Tabbowa beds are lacking. In this study, we investigate the geological and geochronological setting of this area by dating detrital zircons from the Tabbowa beds. The age data will allow testing several hypotheses regarding the plant evolution, the basin development of this region.

  8. Upper Cretaceous Shannon Sandstone Reservoirs, Powder River Basin, Wyoming: Evidence for organic acid diagenesis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hansley, P.L.; Nuccio, V.F.

    Comparison of the petrology of shallow and deep oil reservoirs in the Upper Cretaceous Shannon Sandstone Beds of the Steele Member of the Cody Shale strongly suggests that organic acids have had a more significant impact on the diagenetic alteration of aluminosilicate grains and carbonate cements in the deep reservoirs than in the shallow reservoirs. In shallow reservoirs, detrital grains exhibit minor dissolution, sparse and small overgrowths, and secondary porosity created by dissolution of early calcite cement. However, deeper sandstones are characterized by extensive dissolution of detrital K-feldspar and detrital glauconite grains, and precipitation of abundant, large quartz and feldsparmore » overgrowths. Throughout the Shannon and Steele, dissolution of glauconite and degradation of kerogen were probably aided by clay mineral/organic catalysis, which caused simultaneous reduction of iron and oxidation of kerogen. This process resulted in release of ferrous iron and organic acids and was promoted in the deep reservoirs by higher formation temperatures accounting for more extensive dissolution of aluminosilicate grains. Carbonic acid produced from the dissolution of early calcite cement, decarboxylation of organic matter, and influx of meteoric water after Laramide uplift produced additional dissolution of cements and grains. Dissolution by organic acids and complexing by organic acid anions, however, best explain the intensity of diagenesis and absence of dissolution products in secondary pores and on etched surfaces of framework grains in deep reservoirs.« less

  9. Depositional Architecture of Late Cambrian-Early Ordovician Siliciclastic Barik Formation; Al Huqf Area, Oman

    NASA Astrophysics Data System (ADS)

    Abbasi, Iftikhar Ahmed

    2017-04-01

    Early Paleozoic siliciclastics sediments of the Haima Supergroup are subdivided into a number of formations and members based on lithological characteristics of various rock sequences. One of the distinct sandstone sequence, the Barik Formation (Late Cambrian-Early Ordovician) of the Andam Group is a major deep gas reservoir in central Oman. The sandstone bodies are prospective reservoir rocks while thick shale and clay interbeds act as effective seal. Part of the Barik Formation (lower and middle part) is exposed in isolated outcrops in Al Huqf area as interbedded multistoried sandstone, and green and red shale. The sandstone bodies are up to 2 meters thick and can be traced laterally for 300 m to over 1 km. Most of sandstone bodies show both lateral and vertical stacking. Two types of sandstone lithofacies are identified on the basis of field characteristics; a plane-bedded sandstone lithofacies capping thick red and green color shale beds, and a cross-bedded sandstone lithofacies overlying the plane-bedded sandstone defining coarsening upward sequences. The plane-bedded sandstone at places contains Cruziana ichnofacies and bivalve fragments indicating deposition by shoreface processes. Thick cross-bedded sandstone is interpreted to be deposited by the fluvial dominated deltaic processes. Load-casts, climbing ripples and flaser-bedding in siltstone and red shale indicate influence of tidal processes at times during the deposition of the formation. This paper summarizes results of a study carried out in Al Huqf area outcrops to analyze the characteristics of the sandstone-body geometry, internal architecture, provenance and diagenetic changes in the lower and middle part of the formation. The study shows build-up of a delta complex and its progradation over a broad, low-angle shelf where fluvial processes operate beside shoreface processes in a vegetation free setting. Keywords: Andam Group, Barik Formation, Ordovician sandstone, Al Huqf, Central Oman,

  10. Resonant Ultrasound Spectroscopy studies of Berea sandstone at high temperature

    DOE PAGES

    Davis, Eric S.; Sturtevant, Blake T.; Sinha, Dipen N.; ...

    2016-09-04

    Resonant Ultrasound Spectroscopy was used in this paper to determine the elastic moduli of Berea sandstone from room temperature to 478 K. Sandstone is a common component of oil reservoirs, and the temperature range was chosen to be representative of typical downhole conditions, down to about 8 km. In agreement with previous works, Berea sandstone was found to be relatively soft with a bulk modulus of approximately 6 GPa as compared to 37.5 GPa for α-quartz at room temperature and pressure. Finally, it was found that Berea sandstone undergoes a ~17% softening in bulk modulus between room temperature and 385more » K, followed by an abnormal behavior of similar stiffening between 385 K and 478 K.« less

  11. Resonant Ultrasound Spectroscopy studies of Berea sandstone at high temperature

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Davis, Eric S.; Sturtevant, Blake T.; Sinha, Dipen N.

    Resonant Ultrasound Spectroscopy was used in this paper to determine the elastic moduli of Berea sandstone from room temperature to 478 K. Sandstone is a common component of oil reservoirs, and the temperature range was chosen to be representative of typical downhole conditions, down to about 8 km. In agreement with previous works, Berea sandstone was found to be relatively soft with a bulk modulus of approximately 6 GPa as compared to 37.5 GPa for α-quartz at room temperature and pressure. Finally, it was found that Berea sandstone undergoes a ~17% softening in bulk modulus between room temperature and 385more » K, followed by an abnormal behavior of similar stiffening between 385 K and 478 K.« less

  12. Development of diagenetic seals in carbonates and sandstones

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Schmidt, V.; Almon, W.

    1983-03-01

    Diagenetic seals effectively block the movement of reservoir hydrocarbons in many sandstone and carbonate rock units. Diagenetic seals in sandstones and carbonate rocks encase reservoir rocks with either depositional or diagenetic porosity. Diagenetic reservoir porosity may originate before or after the establishment of an effective diagenetic seal. Hydrocarbon traps with diagenetic seals may conform in their geometry as well to structure or stratigraphy as to diagenetic facies. Therefore, some structural and stratigraphic traps may, in part or entirely, depend on diagenetic seals. Detailed analysis of diagenetic seals in sandstones and carbonate rocks can considerably improve our ability to predict theirmore » occurrence and to recognize their spatial and temporal relationship to reservoir rocks and hydrocarbon migration.« less

  13. Petroleum geology of Carter sandstone (upper Mississippian), Black Warrior Basin, Alabama

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bearden, B.L.; Mancini, E.A.

    1985-03-01

    The presence of combination petroleum traps makes the Black Warrior basin of northwestern Alabama an attractive area for continued hydrocarbon exploration. More than 1,500 wells have been drilled, and more than 90 separate petroleum pools have been discovered. The primary hydrocarbon reservoirs are Upper Mississippian sandstones. The Carter sandstone is the most productive petroleum reservoir in the basin. Productivity of the Carter sandstone is directly related to its environment of deposition. The Carter accumulated within a high constructive elongate to lobate delta, which prograded into the basin from the northwest to the southeast. Carter bar-finger and distal-bar lithofacies constitute themore » primary hydrocarbon reservoirs. Primary porosity in the Carter sandstone has been reduced by quartz overgrowths and calcite cementation. Petroleum traps in the Carter sandstone in central Fayette and Lamar Counties, Alabama, are primarily stratigraphic and combination (structural-stratigraphic) traps. The potential is excellent for future development of hydrocarbon reservoirs in the Upper Mississippian Carter sandstone. Frontier regions south and east of the known productive limits of the Black Warrior basin are ideal areas for continued exploration.« less

  14. Drilling history and stratigraphic correlation of Rose Run sandstone of northeastern Ohio

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Moyer, C.C.

    1988-08-01

    To date, 40 known tests have penetrated the Knox unconformity in Ashtabula, Lake, Trumbull, Geauga, and Portage Counties, Ohio. Prior to 1980, there were only 22 tests. Of these, only 10 penetrated and logged rocks older than the Rose Run sandstone. In the period 1980-1986, two Rose Run discoveries were drilled, one in New Lyme Township of Ashtabula County and one in Burton Township of Geauga County. Both discovery wells have been offset. Attempts have been made to correlate these two areas with older tests in northeastern Ohio and with the Rose Run sandstones of Coshocton County. In northeastern Ohio,more » preliminary studies indicate a Rose Run sandstone and/or dolomite interval approximately 100 ft thick. The upper 50 ft is predominantly sandstone and the lower 50 ft changes locally from sandstone to dolomite. The upper sandy member can be correlated to the A, B, and C sandstone units of Coshocton County.« less

  15. Quantification of the effects of secondary matrix on the analysis of sandstone composition, and a petrographic-chemical technique for retrieving original framework grain modes of altered sandstones.

    PubMed

    Cox, R; Lowe, D R

    1996-05-01

    Most studies of sandstone provenance involve modal analysis of framework grains using techniques that exclude the fine-grained breakdown products of labile mineral grains and rock fragments, usually termed secondary matrix or pseudomatrix. However, the data presented here demonstrate that, when the proportion of pseudomatrix in a sandstone exceeds 10%, standard petrographic analysis can lead to incorrect provenance interpretation. Petrographic schemes for provenance analysis such as QFL and QFR should not therefore be applied to sandstones containing more than 10% secondary matrix. Pseudomatrix is commonly abundant in sandstones, and this is therefore a problem for provenance analysis. The difficulty can be alleviated by the use of whole-rock chemistry in addition to petrographic analysis. Combination of chemical and point-count data permits the construction of normative compositions that approximate original framework grain compositions. Provenance analysis is also complicated in many cases by fundamental compositional alteration during weathering and transport. Many sandstones, particularly shallow marine deposits, have undergone vigorous reworking, which may destroy unstable mineral grains and rock fragments. In such cases it may not be possible to retrieve provenance information by either petrographic or chemical means. Because of this, pseudomatrix-rich sandstones should be routinely included in chemical-petrological provenance analysis. Because of the many factors, both pre- and post-depositional, that operate to increase the compositional maturity of sandstones, petrologic studies must include a complete inventory of matrix proportions, grain size and sorting parameters, and an assessment of depositional setting.

  16. Sandstone-filled normal faults: A case study from central California

    NASA Astrophysics Data System (ADS)

    Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

    2018-05-01

    Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

  17. Laboratory investigation of shale rock to identify fracture propagation in vertical direction to bedding

    NASA Astrophysics Data System (ADS)

    Peng, Tan; Yan, Jin; Bing, Hou; Yingcao, Zhou; Ruxin, Zhang; Zhi, Chang; Meng, Fan

    2018-06-01

    Affected by beddings and natural fractures, fracture geometry in the vertical plane is complex in shale formation, which differs from a simple fracture in homogeneous sandstone reservoirs. However, the propagation mechanism of a hydraulic fracture in the vertical plane has not been well understood. In this paper, a true tri-axial pressure machine was deployed for shale horizontal well fracturing simulation experiments of shale outcrops. The effects of multiple factors on hydraulic fracture vertical propagation were studied. The results revealed that hydraulic fracture initiation and propagation displayed four basic patterns in the vertical plane of laminated shale formation. A hydraulic fracture would cross the beddings under the high vertical stress difference between a vertical stress and horizontal minimum stress of 12 MPa, while a hydraulic fracture propagates along the beddings under a low vertical stress difference of 3 MPa. Four kinds of fracture geometry, including a single main fracture, a nonplanar fracture, a complex fracture, and a complex fracture network, were observed due to the combined effects of flow rate and viscosity. Due to the influence of binding strength (or cementing strength) on the fracture communication effects between a hydraulic fracture and the beddings, the opening region of the beddings takes the shape of an ellipse.

  18. Hydropressure tongues within regionally geopressured lower Tuscaloosa sandstone, Tuscaloosa trend, Louisiana

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McCulloh, R.P.; Purcell, M.D.

    1983-09-01

    A regional study of the Tuscaloosa Formation in Louisiana, undertaken to assess geopressured-geothermal potential, revealed lobate, downdip extensions of the hydropressured zone in lower Tuscaloosa massive sandstone facies below the regional top of geopressure. Normal pressure zones within geopressured section were identified by drilling-mud weights less than 13 lb/gal on electric logs of massive lower Tuscaloosa sandstone; cross section demonstrated updip continuity of these zones with the regional hydropressured zone. These hydropressure tongues are permitted by the anomalously high permeabilities reported from the deep Tuscaloosa trend, and they are attributed to both primary and secondary porosity by investigators of Tuscaloosamore » sandstone petrography. The hydropressure tongues correspond with lobes of thick net sandstone, principally in Pointe Coupee, East Felinicana, East Baton Rouge, and Livingston Parishes in the central Tuscaloosa trend. Limited control suggests at least one hydropressure tongue in the Chandeleur Sound area to the east. Dimensions of hydropressure tongues range up to 27 km (17 mi) parallel to srike and 17 km (11 mi) oblique to strike. In many places, tongues are terminated downdip by faults, which, by acting as pressure seals, prevent the tongues from extending to the downdip edge of the massive sandstone in the expanded sections of the downthrown blocks. The areal extent of geopressured Tuscaloosa sandstone is controlled updip by these fault zones, and downdip by pinch-out of the sandstone units basinward. Local hydropressure tongues diminish the geopressured-geothermal potential of the Tuscaloosa trend, but show no discernible relation to gas-productive areas.« less

  19. Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

    NASA Astrophysics Data System (ADS)

    Zhang, lu; Ban, Jichang

    2018-01-01

    The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

  20. Comparative petrology of arkosic sandstone lithofacies of Cowlitz, Spencer, and Yamhill Formations, northwest Oregon

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Van Atta, R.O.

    Recent discovery (1979) and commercial production of natural gas in arkosic sandstone (Clark and Wilson sand, informal) of the Cowlitz Formation near Mist, Oregon, has stimulated interest in the sedimentology and stratigraphy of Narizian sandstones of northwestern Oregon and the Willamette lowlands. Petrographic study of arkosic sandstone in the lower part of the Cowlitz Formation in surface outcrops in Clatsop, Tillamook, and Columbia Counties, Oregon, and in the Texaco 1 Clatskanie well reveals that the composition is more lithic than that of arkosic sandstone (Clark and Wilson sand) in the upper part of the Cowlitz Formation. The petrography of highlymore » permeable, arkosic sandstone in the Spencer Formation in the western Tualatin Valley south of the Mist gas field is identical in framework grain composition, texture, matrix composition, and heavy mineral content to that of the gas producing Clark and Wilson sand. The petrography of sandstone in the Yamhill Formation in the western Tualatin Valley is very like that of sandstone in the lower part of the Cowlitz Formation of northern northwest Oregon. Diagenetic alteration is more pronounced in arkosic sandstone in the lower part of the Cowlitz Formation and in the Yamhill Formation compared to diagenesis, which is almost nil in arkosic sandstone in the upper part of the cowlitz and in the Spencer Formations. Natural gas exploration will be aided by a clearer and more certain understanding of these petrologic differences between Eocene sandstones in northwestern Oregon.« less

  1. Practical characterization of eolian reservoirs for development: Nugget Sandstone, Utah—Wyoming thrust belt

    NASA Astrophysics Data System (ADS)

    Lindquist, Sandra J.

    1988-04-01

    The Jurassic eolian Nugget Sandstone of the Utah-Wyoming thrust belt is a texturally heterogeneous formation with anisotropic reservoir inherited primarily from the depositional environment. Original reservoir quality has been reduced somewhat by cementation and slightly enhanced by dissolution. Low-permeability, gouge-filled micro-faults compartmentalize the formation, whereas intermittently open fractures provide effective permeability paths locally. Where productive, the Nugget Sandstone ranges from approximately 800 to 1050 ft (244-320 m) thick at subsurface depths of 7500 to 15,000 ft (2286-4572 m). Porosity ranges from several percent to 25%, and permeability covers five orders of magnitude from hundredths of milliDarcies to Darcies. Some Nugget reservoirs are fully charged with hydrocarbons. Different stratification types have unique depositional textures, primary and diagenetic mineralogies, and deformational fabrics resulting in characteristic porosity, permeability, permeability directionality, and pore geometry attributes. Such characteristics can be determined from core analysis, mercury injection, nuclear magnetic resonance, conventional log, dipmeter and production data. Nugget dune deposits (good reservoir facies) primarily consist of grainflow and wind-ripple cross-strata, the former of which have the better reservoir quality and the lesser heterogeneity in bedding texture. High-permeability facies are commonly affected by local quartz and nodular carbonate cementation, chlorite (and lesser illite) precipitation, and minor framework and cement dissolution. Gouge-filled micro-faults are the predominant deformational overprint. Interdune, sand-sheet, and other water-associated deposits (poor reservoir facies) are characterized by low-angle wind-ripple laminae and more irregular bedding, some of which is associated with damp or wet conditions. Water-associated Nugget stratification generally contains the finest grained depositional textures and has the

  2. Revised Lithostratigraphy of the Sonsela Member (Chinle Formation, Upper Triassic) in the Southern Part of Petrified Forest National Park, Arizona

    PubMed Central

    Martz, Jeffrey W.; Parker, William G.

    2010-01-01

    Background Recent revisions to the Sonsela Member of the Chinle Formation in Petrified Forest National Park have presented a three-part lithostratigraphic model based on unconventional correlations of sandstone beds. As a vertebrate faunal transition is recorded within this stratigraphic interval, these correlations, and the purported existence of a depositional hiatus (the Tr-4 unconformity) at about the same level, must be carefully re-examined. Methodology/Principal Findings Our investigations demonstrate the neglected necessity of walking out contacts and mapping when constructing lithostratigraphic models, and providing UTM coordinates and labeled photographs for all measured sections. We correct correlation errors within the Sonsela Member, demonstrate that there are multiple Flattops One sandstones, all of which are higher than the traditional Sonsela sandstone bed, that the Sonsela sandstone bed and Rainbow Forest Bed are equivalent, that the Rainbow Forest Bed is higher than the sandstones at the base of Blue Mesa and Agate Mesa, that strata formerly assigned to the Jim Camp Wash beds occur at two stratigraphic levels, and that there are multiple persistent silcrete horizons within the Sonsela Member. Conclusions/Significance We present a revised five-part model for the Sonsela Member. The units from lowest to highest are: the Camp Butte beds, Lot's Wife beds, Jasper Forest bed (the Sonsela sandstone)/Rainbow Forest Bed, Jim Camp Wash beds, and Martha's Butte beds (including the Flattops One sandstones). Although there are numerous degradational/aggradational cycles within the Chinle Formation, a single unconformable horizon within or at the base of the Sonsela Member that can be traced across the entire western United States (the “Tr-4 unconformity”) probably does not exist. The shift from relatively humid and poorly-drained to arid and well-drained climatic conditions began during deposition of the Sonsela Member (low in the Jim Camp Wash beds), well

  3. Cense Explosion Test Program. Report 1. Cense 1. Explosions in Sandstone

    DTIC Science & Technology

    1977-09-01

    series, "Analysis and Summary of CENSE Data." 10 * _ CHAPTER 2 APPROACH 2.1 DESCRIPTION OF TEST SITE An exposed outcrop of Kayenta sandstone with 180...ft/s seismic velocity previously determined (References 12-14) for the unweathered upper zone of the Kayenta sandstone. 16 I The P-wave propagation...Propagation along the horizontal radial was 8400 ft/s. The seismic velocity pre- viously determined for Kayenta sandstone in this area was 7500 ft/s

  4. Provenance and depositional conditions of Cretaceous-Paleogene boundary sandstones from northeastern Mexico

    NASA Astrophysics Data System (ADS)

    Rehrmann, Stephanie; Augustsson, Carita; Izaguirre Valdez, Rocio Nereyda; Jenchen, Uwe; Schulte, Peter

    2012-12-01

    We compare Late Maastrichtian siliciclastic sandstone in northeastern Mexico with those representing the Cretaceous-Paleogene (K-Pg) boundary to reveal differences in provenance and depositional conditions between background sedimentation and K-Pg sand. Lithology and compositional variations are presented for the deep-water Burgos Basin and the shallow-water La Popa Basin. The Late Maastrichtian sandstones in the Burgos Basin have sharp lower contacts, contain abundant trace fossils and are separated by meter-thick marl layers. They represent sporadic mass flows from coastal areas separated by long phases of hemipelagic sedimentation. The K-Pg sandstone layers are amalgamated, contain thin marl intercalations only in the uppermost part and trace fossils are present in the top sandstone layer only. Also this succession represents mass-flow deposits, but the sand may have been deposited during a very short period. The La Popa Basin sandstones represent deltaic sedimentation interrupted by submarine channel deposition during the K-Pg boundary transition with abundant rip-up clasts and bioclasts at the base. The sandstones of the Burgos Basin are quartz to akosic wacke dominated by quartz (> 90%) and some feldspar (< 10%) in calcite cement and matrix. Lithic fragments are rare and dominated by chert and bioclasts. Ultra-stable heavy minerals (ZTR = 50-80) and plutonic quartz grains (ca. 40% of the total quartz population) are particularly common in the K-Pg sandstones. In the Maastrichtian sandstones, metamorphic heavy minerals, particularly chlorite, clinozoisite, and tourmaline (20-50% of the heavy mineral population), and metamorphic quartz (80% of the quartz population) have higher abundances. The La Popa sandstones are subarkose to arkose and arkosic wacke and have a high abundance of feldspar (15-30%) and lithic fragments (5-20%), mainly of siltstone and carbonate. The sandstones from both basins have chemical compositions typical for recycling (Zr/Sc = 12-27 and

  5. Controls on boron and germanium distribution in the low-sulfur Amos coal bed, Western Kentucky coalfield, USA

    USGS Publications Warehouse

    Hower, J.C.; Ruppert, L.F.; Williams, D.A.

    2002-01-01

    The Duckmantian-aged Amos coal bed is a thin (<51 cm) coal bed that occurs in lobate southwest-trending pods separated by thin sandstones in the Western Kentucky coalfield. The coal bed, which is comprised of up to two benches and a rider coal, is low in ash yield (<6%) and sulfur content (<1%). The coal tends to be thin (<40 cm), but it was heavily mined in the 1980s because it could be combusted as mined. Geochemical analysis of the Amos coal bed shows higher concentrations of B and Ge than other Western Kentucky coal beds. High total B concentrations as well as high B/Be, both considered to be indicators of marine environments, increase toward the top of the coal bed. Most of the B values for the Amos samples range from 66 to 103 ppm (whole coal basis) indicating deposition in a brackish environment. High Ge concentrations in coals have been considered to be a function of seam thickness and proximity to the top and bottom of the coal bed. Thin coals, such as the Amos, are dominated by the coal bed margins and, therefore, have a tendency to have relatively high Ge concentrations. In the case of the Amos coal bed, the lower bench has a higher Ge content, suggesting that the substrate was a more important source of Ge than the roof rock. ?? 2002 Elsevier Science B.V. All rights reserved.

  6. Tidal dunes versus tidal bars: The sedimentological and architectural characteristics of compound dunes in a tidal seaway, the lower Baronia Sandstone (Lower Eocene), Ager Basin, Spain

    NASA Astrophysics Data System (ADS)

    Olariu, Cornel; Steel, Ronald J.; Dalrymple, Robert W.; Gingras, Murray K.

    2012-11-01

    The Lower Eocene Baronia Formation in the Ager Basin is interpreted as a series of stacked compound dunes confined within a tectonically generated embayment or tidal seaway. This differs from the previous interpretation of lower Baronia sand bodies as tidal bars in the front of a delta. The key architectural building block of the succession, the deposit of a single compound dune, forms a 1-3 m-thick, upward coarsening succession that begins with highly bioturbated, muddy, very fine to fine grained sandstone that contains an open-marine Cruziana ichnofacies. This is overlain gradationally by ripple-laminated sandstone that is commonly bioturbated and contains mud drapes. The succession is capped by fine- to coarse-grained sandstones that contain both planar and trough cross-strata with unidirectional or bi-directional paleocurrent directions and occasional thin mud drapes on the foresets. The base of a compound dune is gradational where it migrated over muddy sandstone deposited between adjacent dunes, but is sharp and erosional where it migrated over the stoss side of a previous compound dune. The cross strata that formed by simple superimposed dunes dip in the same direction as the inclined master bedding planes within the compound dune, forming a forward-accretion architecture. This configuration is the fundamental reason why these sandbodies are interpreted as compound tidal dunes rather than as tidal bars, which, in contrast, generate lateral-accretion architecture. In the Baronia, fields of compound dunes generated tabular sandbodies 100s to 1000s of meters in extent parallel to the paleocurrent direction and up to 6 m thick that alternate vertically with highly bioturbated muddy sandstones (up to 10 m thick) that represent the low-energy fringes of the dune fields or periods of high sea level when current speeds decreased. Each cross-stratified sandstone sheet (compound-dune complexes) contains overlapping lenticular "shingles" formed by individual compound

  7. Paleomagnetic and magnetic fabric studies of Lower Triassic red sandstones from the autochthonous cover of the Central Western Carpathians: new insights into paleogeographic setting and tectonic evolution of the area

    NASA Astrophysics Data System (ADS)

    Szaniawski, R.; Jankowski, L.; Ludwiniak, M.; Mazzoli, S.; Szczygieł, J.

    2017-12-01

    The Carpathian Mountains were formed through progressive collision and amalgamation of the Alcapa and Tisza-Dacia microplates with the European Platform. The Central Western Carpathians (CWC) tectonic unit analyzed in this study constitutes a fragment of the Alcapa microplate - research in this area is therefore of great importance in the context of the geotectonic evolution of the Carpathian orogen. Our paleomagnetic and magnetic fabric studies were focused on Lower Triassic red sandstones from the autochthonous cover of the crystalline basement. We present new results from three mountain massifs: Low Tatra, Velka Fatra and Strazovske Vrchy, comparing them with our earlier works performed in the Tatra Mts. Rockmagnetic studies reveal similar results in all four studied regions - the dominant ferromagnetic carrier in red sandstones is hematite, while the magnetic fabric is mostly controlled by paramagnetic minerals. AMS results outline a bedding parallel foliation and a tectonic lineation. This lineation lies in the bedding plane but is somewhat oblique to the present horizontal plane. The fact that the lineation is not exactly parallel to the strike of the beds is most likely due to multistage deformation: the lineation is related to bedding parallel shortening associated with the folding and thrusting stage, while present-day bedding attitude results at least partially from rotations associated with subsequent uplift and/or faulting. Paleomagnetic analysis indicate that hematite carrier records characteristic remanent component of high unblocking temperatures (680°C) and both normal (dominant) and reversed polarity. Paleomagnetic inclinations are similar to those expected from reference paleomagnetic data from the European Platform. Declination values are rather similar in all four studied areas and imply moderate counterclockwise rotations of the CWC. These results are incompatible with some of the previous paleomagnetic studies of younger rocks from the CWC

  8. Effects of Pisha sandstone content on solute transport in a sandy soil.

    PubMed

    Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

    2016-02-01

    In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. A condensed middle Cenomanian succession in the Dakota Sandstone (Upper Cretaceous), Sevilleta National Wildlife Refuge, Socorro County, New Mexico

    USGS Publications Warehouse

    Hook, Stephen C.; Cobban, William A.

    2007-01-01

    The upper part of the Dakota Sandstone exposed on the Sevilleta National Wildlife Refuge, northern Socorro County, New Mexico, is a condensed, Upper Cretaceous, marine succession spanning the first five middle Cenomanian ammonite zones of the U.S. Western Interior. Farther north in New Mexico these five ammonite zones occur over a stratigraphic interval more than an order of magnitude thicker. The basal part of this marine sequence was deposited in Seboyeta Bay, an elongate east-west embayment into New Mexico that marked the initial transgression of the western shoreline of the Late Cretaceous seaway into New Mexico. The primary mechanism for condensing this section was nearshore, submarine erosion, although nondeposition played a minor role. The ammonite fossils from each zone are generally fragments of internal molds that are corroded on one side, indicating submarine burial, erosion of the prefossilized steinkern, and corrosion on the sea floor. In addition, the base of the condensed succession is marked by a thin bed that contains abundant, white-weathering, spherical to cylindrical phosphate nodules, many of which contain a cylindrical axial cavity of unknown origin. The nodules lie on the bedding surface of the highly burrowed, ridge-forming sandstone near the top of the Dakota and occur in the overlying breccia. The breccia consists of rip-up clasts of sandstone and eroded internal molds of the ammonite Conlinoceras tarrantense, the zonal index for the basal middle Cenomanian. The nodules below the breccia imply a time of erosion followed by nondeposition or sediment bypass during which the phosphatization occurred. The breccia implies a time of submarine erosion, probably storm-related. Remarkably, this condensed succession and the basal part of the overlying Mancos Shale tongue contain one of the most complete middle Cenomanian ammonite sequences in the U.S. Western Interior. Five of the six ammonite zones that characterize the middle Cenomanian of the

  10. Petroleum produced water disposal: Mobility and transport of barium in sandstone and dolomite rocks.

    PubMed

    Ebrahimi, Pouyan; Vilcáez, Javier

    2018-09-01

    To assess the risk of underground sources of drinking water contamination by barium (Ba) present in petroleum produced water disposed into deep saline aquifers, we examined the effect of salinity (NaCl), competition of cations (Ca, Mg), temperature (22 and 60°C), and organic fracturing additives (guar gum) on the sorption and transport of Ba in dolomites and sandstones. We found that at typical concentration levels of NaCl, Ca, and Mg in petroleum produced water, Ba sorption in both dolomites and sandstones is inhibited by the formation of Ba(Cl) + complexes in solution and/or the competition of cations for binding sites of minerals. The inhibition of Ba sorption by both mechanisms is greater in dolomites than in sandstones. This is reflected by a larger decrease in the breakthrough times of Ba through dolomites than through sandstones. We found that the presence of guar gum has little influence on the sorption and thus the transport of Ba in both dolomites and sandstones. Contrary to most heavy metals, Ba sorption in both dolomites and sandstones decreases with increasing temperature, however the reducing effect of temperature on Ba sorption is relevant only at low salinity conditions. Higher inhibition of Ba sorption in dolomites than in sandstones is due to the greater reactivity of dolomite over sandstone. The results of this study which includes the formulation of a reactive transport model and estimation of partition coefficients of Ba in dolomites and sandstones have significant implications in understanding and predicting the mobility and transport of Ba in deep dolomite and sandstone saline aquifers. Copyright © 2018 Elsevier B.V. All rights reserved.

  11. ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jennie Ridgley

    2000-01-21

    An additional 450 wells were added to the structural database; there are now 2550 wells in the database with corrected tops on the Juana Lopez, base of the Bridge Creek Limestone, and datum. This completes the structural data base compilation. Fifteen oil and five gas fields from the Mancos-ElVado interval were evaluated with respect to the newly defined sequence stratigraphic model for this interval. The five gas fields are located away from the structural margins of the deep part of the San Juan Basin. All the fields have characteristics of basin-centered gas and can be considered as continuous gas accumulationsmore » as recently defined by the U.S. Geological Survey. Oil production occurs in thinly interbedded sandstone and shale or in discrete sandstone bodies. Production is both from transgressive and regressive strata as redefined in this study. Oil production is both stratigraphically and structurally controlled with production occurring along the Chaco slope or in steeply west-dipping rocks along the east margin of the basin. The ElVado Sandstone of subsurface usage is redefined to encompass a narrower interval; it appears to be more time correlative with the Dalton Sandstone. Thus, it was deposited as part of a regressive sequence, in contrast to the underlying rock units which were deposited during transgression.« less

  12. Statistical analyses on sandstones: Systematic approach for predicting petrographical and petrophysical properties

    NASA Astrophysics Data System (ADS)

    Stück, H. L.; Siegesmund, S.

    2012-04-01

    Sandstones are a popular natural stone due to their wide occurrence and availability. The different applications for these stones have led to an increase in demand. From the viewpoint of conservation and the natural stone industry, an understanding of the material behaviour of this construction material is very important. Sandstones are a highly heterogeneous material. Based on statistical analyses with a sufficiently large dataset, a systematic approach to predicting the material behaviour should be possible. Since the literature already contains a large volume of data concerning the petrographical and petrophysical properties of sandstones, a large dataset could be compiled for the statistical analyses. The aim of this study is to develop constraints on the material behaviour and especially on the weathering behaviour of sandstones. Approximately 300 samples from historical and presently mined natural sandstones in Germany and ones described worldwide were included in the statistical approach. The mineralogical composition and fabric characteristics were determined from detailed thin section analyses and descriptions in the literature. Particular attention was paid to evaluating the compositional and textural maturity, grain contact respectively contact thickness, type of cement, degree of alteration and the intergranular volume. Statistical methods were used to test for normal distributions and calculating the linear regression of the basic petrophysical properties of density, porosity, water uptake as well as the strength. The sandstones were classified into three different pore size distributions and evaluated with the other petrophysical properties. Weathering behavior like hygric swelling and salt loading tests were also included. To identify similarities between individual sandstones or to define groups of specific sandstone types, principle component analysis, cluster analysis and factor analysis were applied. Our results show that composition and porosity

  13. Integrated geomechanical, petrographical and petrophysical study of the sandstones of the Wajid Group, SW Saudi Arabia

    NASA Astrophysics Data System (ADS)

    Benaafi, Mohammed; Hariri, Mustafa; Al-Shaibani, Abdulaziz; Abdullatif, Osman; Makkawi, Mohammed

    2018-07-01

    The Cambro-Permian siliciclastic succession in southwestern Saudi Arabia is represented by the Wajid Group, which consists mainly of fluvial, shallow marine, aeolian, and glacial sandstones. The Wajid Group comprises the Dibsiyah, Sanamah, Qalibah, Khusayyayn, and Juwayl Formations. It is exposed in the Wadi Al-Dawasir area and extends to Najran City. The sandstones of the Wajid Group serve as groundwater aquifers in the Wadi Al-Dawasir and Najran areas and host hydrocarbon (mainly gas) reservoirs in the Rub' Al-Khali Basin. This study aims to characterize the geomechanical properties (rock strength and Young's modulus) of the sandstones of the Wajid Group using field and experimental techniques. A further objective is to investigate the relationships between the geomechanical properties and the petrographical and petrophysical properties of the studied sandstones. The geomechanical properties of the studied sandstones vary from glacial to non-glacial sandstones, as the glacial sandstones display high values of the geomechanical properties with high variability indices. Four geological factors including grain size, cement content, porosity and permeability were observed as the main controls on the geomechanical behaviour of the studied sandstones except for the Khusayyayn sandstone, where the mineral composition was also important. Significant correlations were observed between the petrographical and petrophysical properties and the geomechanical properties of the glacial sandstones. Predictive models of the geomechanical properties (RN, UCS, and E) were generated using regression analysis to account for the glacial sandstones.

  14. CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

    NASA Astrophysics Data System (ADS)

    Gent, Christopher; Williams, John

    2017-04-01

    Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

  15. Factors controlling reservoir quality in tertiary sandstones and their significance to geopressured geothermal production

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Loucks, R.G.; Richmann, D.L.; Milliken, K.L.

    1981-01-01

    Variable intensity of diagenesis is the factor primarily responsible for contrasting regional reservoir quality of Tertiary sandstones from the upper and lower Texas coast. Detailed comparison of Frio sandstone from the Chocolate Bayou/Danbury Dome area, Brazoria County, and Vicksburg sandstones from the McAllen Ranch Field area, Hidalgo County, reveals that extent of diagenetic modification is most strongly influenced by (1) detrital mineralogy and (2) regional geothermal gradients. The regional reservoir quality of Frio sandstones from Brazoria County is far better than that characterizing Vicksburg sandstones from Hidalgo County, especially at depths suitable for geopressured geothermal energy production. However, in predictingmore » reservoir quality on a site-specific basis, locally variable factors such as relative proportions for porosity types, pore geometry as related to permeability, and local depositional environment must also be considered. Even in an area of regionally favorable reservoir quality, such local factors can significantly affect reservoir quality and, hence, the geothermal production potential of a specific sandstone unit.« less

  16. X-ray imaging of water motion during capillary imbibition: A study on how compaction bands impact fluid flow in Bentheim sandstone

    NASA Astrophysics Data System (ADS)

    Pons, A.; David, C.; Fortin, J.; Stanchits, S.; MenéNdez, B.; Mengus, J. M.

    2011-03-01

    To investigate the effect of compaction bands (CB) on fluid flow, capillary imbibition experiments were performed on Bentheim sandstone specimens (initial porosity ˜22.7%) using an industrial X-ray scanner. We used a three-step procedure combining (1) X-ray imaging of capillary rise in intact Bentheim sandstone, (2) formation of compaction band under triaxial tests, at 185 MPa effective pressure, with acoustic emissions (AE) recording for localization of the induced damage, and (3) again X-ray imaging of capillary rise in the damaged specimens after the unloading. The experiments were performed on intact cylindrical specimens, 5 cm in diameter and 10.5 cm in length, cored in different orientations (parallel or perpendicular to the bedding). Analysis of the images obtained at different stages of the capillary imbibition shows that the presence of CB slows down the imbibition and disturbs the geometry of water flow. In addition, we show that the CB geometry derived from X-ray density maps analysis is well correlated with the AE location obtained during triaxial test. The analysis of the water front kinetics was conducted using a simple theoretical model, which allowed us to confirm that compaction bands act as a barrier for fluid flow, not fully impermeable though. We estimate a contrast of permeability of a factor of ˜3 between the host rock and the compaction bands. This estimation of the permeability inside the compaction band is consistent with estimations done in similar sandstones from field studies but differs by 1 order of magnitude from estimations from previous laboratory measurements.

  17. Isotopic age of the Black Forest Bed, Petrified Forest Member, Chinle Formation, Arizona: An example of dating a continental sandstone

    USGS Publications Warehouse

    Riggs, N.R.; Ash, S.R.; Barth, A.P.; Gehrels, G.E.; Wooden, J.L.

    2003-01-01

    Zircons from the Black Forest Bed, Petrified Forest Member, Chinle Formation, in Petrified Forest National Park, yield ages that range from Late Triassic to Late Archean. Grains were analyzed by multigrain TIMS (thermal-ionization mass spectrometry), single-crystal TIMS, and SHRIMP (sensitive, high-resolution ion-microprobe). Multiple-grain analysis yielded a discordia trajectory with a lower intercept of 207 ?? 2 Ma, which because of the nature of multiple-grain sampling of a detrital bed, is not considered conclusive. Analysis of 29 detrital-zircon grains by TIMS yielded U-PB ages of 2706 ?? 6 Ma to 206 ?? 6 Ma. Eleven of these ages lie between 211 and 216 ?? 6.8 Ma. Our statistical analysis of these grains indicates that the mean of the ages, 213 ?? 1.7 Ma, reflects more analytical error than geologic variability in sources of the grains. Grains with ages of ca. 1400 Ma were derived from the widespread plutons of that age exposed throughout the southwestern Cordillera and central United States. Twelve grains analyzed by SHRIMP provide 206Pb*/238U ages from 214 ?? 2 Ma to 200 ?? 4 Ma. We use these data to infer that cores of inherited material were present in many zircons and that single-crystal analysis provides an accurate estimation of the age of the bed. We further propose that, even if some degree of reworking has occurred, the very strong concentration of ages at ca. 213 Ma provides a maximum age for the Black Forest Bed of 213 ?? 1.7 Ma. The actual age of the bed may be closer to 209 Ma. Dating continental successions is very difficult when distinct ash beds are not clearly identified, as is the case in the Chinle Formation. Detrital zircons in the Black Forest Bed, however, are dominated by an acicular morphology with preserved delicate terminations. The shape of these crystals and their inferred environment of deposition in slow-water settings suggest that the crystals were not far removed from their site of deposition in space and likely not far in time

  18. Energy evolution mechanism in process of Sandstone failure and energy strength criterion

    NASA Astrophysics Data System (ADS)

    Wang, Yunfei; Cui, Fang

    2018-07-01

    To reveal the inherent relation between energy change and confining pressure during the process of sandstone damage, and its characteristics of energy storage and energy dissipation in different deformation stage. Obtaining the mechanical parameters by testing the Sandstone of two1 coal seam roof under uniaxial compression in Zhaogu coalmine, using Particle Flow Code (PFC) and fish program to get the meso-mechanical parameters, studying Sandstone energy evolution mechanism under different confining pressures, and deducing energy strength criterion based on energy principle of rock failure, some main researching results are reached as follows: with the increasing of confining pressure, the Sandstone yield stage and ductility increases, but brittleness decreases; Under higher confining pressure, the elastic strain energy of Sandstone before peak approximately keeps constant in a certain strain range, and rock absorbs all the energy which converts into surface energy required for internal damage development; Under lower confining pressure, Sandstone no longer absorbs energy with increasing strain after peak under lower confining pressure, while it sequentially absorbs energy under higher confining pressure; Under lower confining pressure, the energy Sandstone before peak absorbed mainly converts into elastic strain energy, while under higher confining pressure, dissipation energy significantly increases before peak, which indicates that the degree rock strength loss is higher under higher confining pressure; with the increasing of confining pressure, the limit of elastic strain energy increases and there exists a favourable linear variation relationship; At the peak point, the ratio of elastic strain energy to total energy of Sandstone nonlinearly decreases, while the ratio of dissipation energy to total energy nonlinearly increases with the increasing of confining pressure; According to energy evolution mechanism of rock failure, an energy strength criterion is

  19. The Point Lookout Sandstone: a tale of two cores, or petrology, diagenesis, and reservoir properties of Point Lookout Sandstone, Southern Ute Indian Reservation, San Juan Basin, Colorado

    USGS Publications Warehouse

    Keighin, C.W.; Zech, R.S.; Dunbar, R.W.

    1993-01-01

    The Point Lookout sandstones are quartz-rich, fine to very-fine grained, and contain moderately variable quantities of potassium feldspar (2 to 20 modal percent) and lithic fragments (9 to 20 modal percent). Locally, sandstone is tightly cemented by carbonate cement; clays are not important as cementing agents, although they significantly reduce permeability of some samples. Pores are small; many are intergranular micropores between crystals of authigenic clay. Depositional environments are highly variable and range from lower shoreface to coastal plain and include minor deltaic environments. The best reservoir characteristics are generally in the upper shoreface sandstones. -from Authors

  20. 3D visualization of liquefaction-induced dune collapse in the Navajo Sandstone, Utah, USA

    NASA Astrophysics Data System (ADS)

    Ford, Colby; Nick, Kevin; Bryant, Gerald

    2015-04-01

    The eolian Navajo Sandstone outcrop on the Canyon Overlook Trail in Zion National Park in Southern Utah is dissected by modern erosion in a way which reveals a great deal of the three-dimensional architecture of a major soft-sediment deformation event. The feature is bounded below by a well-developed interdune complex made up of two superimposed carbonate lenses, above by an irregular truncational surface, and incorporates 3 - 10 m of sandstone over an approximately 2 km area. The material above the deformed interval is undeformed cross-bedded sandstone, with crossbeds downlapping onto the surface of truncation. The stratigraphic confinement of deformation and the irregularity of the upper bounding surface suggests a deformation process which created topography, which was in turn covered by the next upwind dune before it could be eroded flat. The deformed material itself is laterally segmented by a stacked succession of shear surfaces, which all strike approximately perpendicular to the paleo-wind direction and dip at decreasing angles in the down paleo-wind direction. These factors point to the collapse of a major dune into the downwind interdune area, likely initiated by liquefaction in the interdune complex. The foundering of the dune's toe into the liquefied area created a powerful lateral stress field which did not extend significantly into the subsurface. The dune collapse process has been used in the past to describe other soft-sediment deformation features in the Navajo Sandstone, but this site provides a wealth of physical details which were not previously associated with dune collapse. Shear surfaces originate in the interdune deposit as slip between laminae, then the cohesive muds provided support as they were thrust upward to angles of up to 50 degrees. The margins of the site also contain important paleoenvironmental indicators. Dinosaur tracks are exposed both at the extreme upwind and downwind margins of the interdune deposit in and slightly above

  1. Traces of the heritage arising from the Macelj sandstone

    NASA Astrophysics Data System (ADS)

    Golež, Mateja

    2014-05-01

    The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in

  2. Correlation chart of Pennsylvanian rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania showing approximate position of coal beds, coal zones, and key stratigraphic units

    USGS Publications Warehouse

    Ruppert, Leslie F.; Trippi, Michael H.; Slucher, Ernie R.

    2010-01-01

    This report contains a simplified provisional correlation chart that was compiled from both published and unpublished data in order to fill a need to visualize the currently accepted stratigraphic relations between Appalachian basin formations, coal beds and coal zones, and key stratigraphic units in the northern, central, and southern Appalachian basin coal regions of Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania. Appalachian basin coal beds and coal zones were deposited in a variety of geologic settings throughout the Lower, Middle, and Upper Pennsylvanian and Pennsylvanian formations were defined on the presence or absence of economic coal beds and coarse-grained sandstones that often are local or regionally discontinuous. The correlation chart illustrates how stratigraphic units (especially coal beds and coal zones) and their boundaries can differ between States and regions.

  3. Influence of Water Saturation on Thermal Conductivity in Sandstones

    NASA Astrophysics Data System (ADS)

    Fehr, A.; Jorand, R.; Koch, A.; Clauser, C.

    2009-04-01

    Information on thermal conductivity of rocks and soils is essential in applied geothermal and hydrocarbon maturation research. In this study, we investigate the dependence of thermal conductivity on the degree of water saturation. Measurements were made on five sandstones from different outcrops in Germany. In a first step, we characterized the samples with respect to mineralogical composition, porosity, and microstructure by nuclear magnetic resonance (NMR) and mercury injection. We measured thermal conductivity with an optical scanner at different levels of water saturation. Finally we present a simple and easy model for the correlation of thermal conductivity and water saturation. Thermal conductivity decreases in the course of the drying of the rock. This behaviour is not linear and depends on the microstructure of the studied rock. We studied different mixing models for three phases: mineral skeleton, water and air. For argillaceous sandstones a modified arithmetic model works best which considers the irreducible water volume and different pore sizes. For pure quartz sandstones without clay minerals, we use the same model for low water saturations, but for high water saturations a modified geometric model. A clayey sandstone rich in feldspath shows a different behaviour which cannot be explained by simple models. A better understanding will require measurements on additional samples which will help to improve the derived correlations and substantiate our findings.

  4. Dependence of Thermal Conductivity on Water Saturation of Sandstones

    NASA Astrophysics Data System (ADS)

    Fehr, A.; Jorand, R.; Koch, A.; Clauser, C.

    2008-12-01

    Information on thermal conductivity of rocks and soils is essential in applied geothermal and hydrocarbon maturation research. In this study, we investigate the dependence of thermal conductivity on the degree of water saturation. Measurements were made on five sandstones from different outcrops in Germany. In a first step, we characterized the samples with respect to mineralogical composition, porosity, and microstructure by nuclear magnetic resonance (NMR) and mercury injection. We measured thermal conductivity with an optical scanner at different levels of water saturation. Finally we present a simple and easy model for the correlation of thermal conductivity and water saturation. Thermal conductivity decreases in the course of the drying of the rock. This behaviour is not linear and depends on the microstructure of the studied rock. We studied different mixing models for three phases: mineral skeleton, water and air. For argillaceous sandstones a modified arithmetic model works best which considers the irreducible water volume and different pore sizes. For pure quartz sandstones without clay minerals, we use the same model for low water saturations, but for high water saturations a modified geometric model. A clayey sandstone rich in feldspath shows a different behaviour which cannot be explained by simple models. A better understanding will require measurements on additional samples which will help to improve the derived correlations and substantiate our findings.

  5. Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

    NASA Astrophysics Data System (ADS)

    Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

    2016-11-01

    Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

  6. Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

    NASA Astrophysics Data System (ADS)

    Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

    2013-04-01

    The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

  7. Influence of Structural Features and Fracture Processes on Surface Roughness: A Case Study from the Krosno Sandstones of the Górka-Mucharz Quarry (Little Beskids, Southern Poland)

    NASA Astrophysics Data System (ADS)

    Pieczara, Łukasz

    2015-09-01

    The paper presents the results of analysis of surface roughness parameters in the Krosno Sandstones of Mucharz, southern Poland. It was aimed at determining whether these parameters are influenced by structural features (mainly the laminar distribution of mineral components and directional distribution of non-isometric grains) and fracture processes. The tests applied in the analysis enabled us to determine and describe the primary statistical parameters used in the quantitative description of surface roughness, as well as specify the usefulness of contact profilometry as a method of visualizing spatial differentiation of fracture processes in rocks. These aims were achieved by selecting a model material (Krosno Sandstones from the Górka-Mucharz Quarry) and an appropriate research methodology. The schedule of laboratory analyses included: identification analyses connected with non-destructive ultrasonic tests, aimed at the preliminary determination of rock anisotropy, strength point load tests (cleaved surfaces were obtained due to destruction of rock samples), microscopic analysis (observation of thin sections in order to determine the mechanism of inducing fracture processes) and a test method of measuring surface roughness (two- and three-dimensional diagrams, topographic and contour maps, and statistical parameters of surface roughness). The highest values of roughness indicators were achieved for surfaces formed under the influence of intragranular fracture processes (cracks propagating directly through grains). This is related to the structural features of the Krosno Sandstones (distribution of lamination and bedding).

  8. Reservoir sedimentology of the Big Injun sandstone in Granny Creek field, West Virginia

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zou, Xiangdong; Donaldson, K.; Donaldson, A.C.

    1992-01-01

    Big Injun sandstones of Granny Creek oil field (WV) are interpreted as fluvial-deltaic deposits from core and geophysical log data. The reservoir consists of two distinctive lithologies throughout the field; fine-grained sandstones overlain by pebbly and coarse-grained sandstones. Lower fine-grained sandstones were deposited in westward prograding river-mouth bars, where distal, marine-dominant proximal, and fluvial-dominant proximal bar subfacies are recognized. Principal pay is marine-influenced proximal bar, where porosity ranges from 13 to 23% and permeability, up to 24 md. Thin marine transgressive shales and their laterally equivalent low-permeability sandstones bound time-rock sequences generally less than 10 meters thick. Where field mapped,more » width of prograding bar sequence is approximately 2.7 km (dip trend), measured from truncated eastern edge (pre-coarse-grained member erosional surface) to distal western margin. Dip-trending elongate lobes occur within marine-influenced proximal mouth-bar area, representing thickest part of tidally influenced preserved bar. Upper coarse-grained part of reservoir consists of pebbly sandstones of channel fill from bedload streams. Laterally persistent low permeability cemented interval in lower part commonly caps underlying pay zone and probably serves as seal to vertical oil migration. Southwest paleoflow trends based on thickness maps of unit portent emergence of West Virginia dome, which influences erosion patterns of pre-Greenbrier unconformity for this combination oil trap.« less

  9. Characterization of the Lower Cambrian sandstone aquifer in the Swedish Baltic Sea area - assessment regarding its potential suitability for storage of CO2

    NASA Astrophysics Data System (ADS)

    Erlström, M.; Sivhed, U.

    2012-04-01

    In the Baltic region the Cambrian sandstone is considered to have great economic value concerning its aquifer and reservoir properties. Its potential as petroleum reservoir is well known, especially from the Polish, Lithuanian and Russian sectors of the Baltic Sea where oil and gas has been found in anticline traps in the sandstone sequence. Offshore exploration in the Swedish sector has so far not encountered any significant findings of oil and gas. However, the extensive exploration has generated data, which is now being used for assessing the overall properties regarding suitability for storage of CO2. The Swedish primary industry has a great interest in finding potential sites for storage of CO2. A suitable site in the Baltic Sea would be a most favourable alternative in comparison to more remote alternatives such as deep saline aquifers in the North Sea. The Lower Cambrian is in the Swedish sector of the Baltic Sea composed of three main sandstone units varying in thickness between 5 and 50 m occurring within an up to 250 m thick Cambrian sequence dominated by fine-grained terriclastic sediments. The limit of Lower Palaeozoic sequence in the Baltic area is today defined by erosional truncation because of the gently dipping Lower Palaeozoic sequence. To the north and northwest, the limit is found in the Pre-Quaternary, whereas the erosional limit is deeply buried beneath Permian and Mesozoic sediments to the south. Here the Lower Palaeozoic limit is buried to depths reaching more than 2 km. The Cambrian sequence in the distal parts of the Swedish sector occurs at depths of c. 1300 m while it constitutes the bedrock surface in a narrow zone trending from Öland to the north of of Gotland. Sandstone beds constitute 40-60% of the total Cambrian sequence. The main sandstone units have a regional distribution of several thousands of square kilometres. The up to 50 m thick Faludden sandstone member exhibits the best reservoir properties including porosities in the

  10. Reservoir assessment of the Nubian sandstone reservoir in South Central Gulf of Suez, Egypt

    NASA Astrophysics Data System (ADS)

    El-Gendy, Nader; Barakat, Moataz; Abdallah, Hamed

    2017-05-01

    The Gulf of Suez is considered as one of the most important petroleum provinces in Egypt and contains the Saqqara and Edfu oil fields located in the South Central portion of the Gulf of Suez. The Nubian sandstone reservoir in the Gulf of Suez basin is well known for its great capability to store and produce large volumes of hydrocarbons. The Nubian sandstone overlies basement rocks throughout most of the Gulf of Suez region. It consists of a sequence of sandstones and shales of Paleozoic to Cretaceous age. The Nubian sandstone intersected in most wells has excellent reservoir characteristics. Its porosity is controlled by sedimentation style and diagenesis. The cementation materials are mainly kaolinite and quartz overgrowths. The permeability of the Nubian sandstone is mainly controlled by grain size, sorting, porosity and clay content especially kaolinite and decreases with increase of kaolinite. The permeability of the Nubian Sandstone is evaluated using the Nuclear Magnetic Resonance (NMR technology) and formation pressure data in addition to the conventional logs and the results were calibrated using core data. In this work, the Nubian sandstone was investigated and evaluated using complete suites of conventional and advanced logging techniques to understand its reservoir characteristics which have impact on economics of oil recovery. The Nubian reservoir has a complicated wettability nature which affects the petrophysical evaluation and reservoir productivity. So, understanding the reservoir wettability is very important for managing well performance, productivity and oil recovery.

  11. Fractures and stresses in Bone Spring sandstones

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Warpinski, N.R.; Sattler, A.R.; Lorenz, J.C.

    This project was a collaboration between Sandia National Laboratories and the Harvey E. Yates Company (Heyco), Roswell, NM, conducted under the auspices of Department of Energy's Oil Recovery Technology Partnership. The project applied Sandia perspectives on the effects of natural fractures, stress, and sedimentology for the stimulation and production of low permeability gas reservoirs to low permeability oil reservoirs, such as those typified by the Bone Spring sandstones of the Delaware Basin, southeast New Mexico. This report details the results and analyses obtained in 1990 from core, logs, stress, and other data taken from three additional development wells. An overallmore » summary gives results from all five wells studied in this project in 1989--1990. Most of the results presented are believed to be new information for the Bone Spring sandstones.« less

  12. Mineralogy and diagenesis of low-permeability sandstones of Late Cretaceous age, Piceance Creek Basin, northwestern Colorado

    USGS Publications Warehouse

    Hansley, Paula L.; Johnson, Ronald C.

    1980-01-01

    This report presents preliminary results of a mineralogic and diagenetic study of some low-permeability sandstones from measured surface sections and cores obtained from drill holes in the Piceance Creek Basin of northwestern Colorado. A documentation of the mineralogy and diagenetic history will aid in the exploration for natural gas and in the development of recovery technology in these low-permability sandstones. These sandstones are in the nonmarine upper part of the Mesaverde Formation (or Group) of Late Cretaceous age and are separated from overlying lower Tertiary rocks by a major regional unconformity. Attention is focused on the sandstone units of the Ohio Creek Member, which directly underlies the unconformity; however, comparisons between the mineralogy of the Ohio Creek strata and that of the underlying sandstone units are made whenever possible. The Ohio Creek is a member of the Hunter Canyon Formation (Mesaverde Group) in the southwestern part of the basin, and the Mesaverde Formation in the southern and central parts of the basin. The detrital mineralogy is fairly constant throughout all of these nonrnarine Cretaceous sandstone units; however, in the southeastern part of the basin, there is an increase in percentage of feldspar, quartzite, and igneous rock fragments in sandstones of the Ohio Creek Member directly underlying the unconformity. In the southwestern part of the basin, sandstones of the Ohio Creek Member are very weathered and are almost-entirely comprised of quartz, chert, and kaolinite. A complex diagenetic history, partly related to the overlying unconformity, appears to be responsible for transforming these sandstones into potential gas reservoirs. The general diagenetic sequence for the entire Upper Cretaceous interval studied is interpreted to be (early to late): early(?) calcite cement, chlorite, quartz overgrowths, calcite cement, secondary porosity, analcime (surface only), kaolinite and illite, and late carbonate cements

  13. Correlative multiple porosimetries for reservoir sandstones with adoption of a new reference-sample-guided computed-tomographic method.

    PubMed

    Jin, Jae Hwa; Kim, Junho; Lee, Jeong-Yil; Oh, Young Min

    2016-07-22

    One of the main interests in petroleum geology and reservoir engineering is to quantify the porosity of reservoir beds as accurately as possible. A variety of direct measurements, including methods of mercury intrusion, helium injection and petrographic image analysis, have been developed; however, their application frequently yields equivocal results because these methods are different in theoretical bases, means of measurement, and causes of measurement errors. Here, we present a set of porosities measured in Berea Sandstone samples by the multiple methods, in particular with adoption of a new method using computed tomography and reference samples. The multiple porosimetric data show a marked correlativeness among different methods, suggesting that these methods are compatible with each other. The new method of reference-sample-guided computed tomography is more effective than the previous methods when the accompanied merits such as experimental conveniences are taken into account.

  14. Degradation of Glaukonite Sandstone as a Result of Alkali-Silica Reactions in Cement Mortar.

    PubMed

    Czapik, Przemysław

    2018-05-30

    The mechanism of concrete degradation as a result of an alkali-silica reaction (ASR) largely depends on the mineral composition and microstructure of the reactive aggregate. This paper shows the reactivity results of quartz-glaukonitic sandstone, which is mainly responsible for the reactivity of some post-glacial gravels, available in Poland. After initial petrographic observations under a light microscope, the mode of sandstone degradation triggered by the reaction with sodium and potassium hydroxides was identified using scanning electron microscopy (SEM). It has been found that chalcedony agglomerates present in sandstone are separated from the rock matrix and subsequently cause the cracks formation in this matrix. Additionally, microcrystalline and potentially reactive silica is also dispersed in sandstone cement.

  15. Elastic Dispersion and Attenuation in Fully Saturated Sandstones: Role of Mineral Content, Porosity, and Pressures

    NASA Astrophysics Data System (ADS)

    Pimienta, Lucas; Borgomano, Jan V. M.; Fortin, Jérôme; Guéguen, Yves

    2017-12-01

    Because measuring the frequency dependence of elastic properties in the laboratory is a technical challenge, not enough experimental data exist to test the existing theories. We report measurements of three fluid-saturated sandstones over a broad frequency band: Wilkenson, Berea, and Bentheim sandstones. Those sandstones samples, chosen for their variable porosities and mineral content, are saturated by fluids of varying viscosities. The samples elastic response (Young's modulus and Poisson's ratio) and hydraulic response (fluid flow out of the sample) are measured as a function of frequency. Large dispersion and attenuation phenomena are observed over the investigated frequency range. For all samples, the variation at lowest frequency relates to a large fluid flow directly measured out of the rock samples. These are the cause (i.e., fluid flow) and consequence (i.e., dispersion/attenuation) of the transition between drained and undrained regimes. Consistently, the characteristic frequency correlates with permeability for each sandstone. Beyond this frequency, a second variation is observed for all samples, but the rocks behave differently. For Berea sandstone, an onset of dispersion/attenuation is expected from both Young's modulus and Poisson's ratio at highest frequency. For Bentheim and Wilkenson sandstones, however, only Young's modulus shows dispersion/attenuation phenomena. For Wilkenson sandstone, the viscoelastic-like dispersion/attenuation response is interpreted as squirt flow. For Bentheim sandstone, the second effect does not fully follow such response, which could be due to a lower accuracy in the measured attenuation or to the occurence of another physical effect in this rock sample.

  16. Micro-mechanics of hydro-mechanical coupled processes during hydraulic fracturing in sandstone

    NASA Astrophysics Data System (ADS)

    Caulk, R.; Tomac, I.

    2017-12-01

    This contribution presents micro-mechanical study of hydraulic fracture initiation and propagation in sandstone. The Discrete Element Method (DEM) Yade software is used as a tool to model fully coupled hydro-mechanical behavior of the saturated sandstone under pressures typical for deep geo-reservoirs. Heterogeneity of sandstone strength tensile and shear parameters are introduced using statistical representation of cathodoluminiscence (CL) sandstone rock images. Weibull distribution of statistical parameter values was determined as a best match of the CL scans of sandstone grains and cement between grains. Results of hydraulic fracturing stimulation from the well bore indicate significant difference between models with the bond strengths informed from CL scans and uniform homogeneous representation of sandstone parameters. Micro-mechanical insight reveals formed hydraulic fracture typical for mode I or tensile cracking in both cases. However, the shear micro-cracks are abundant in the CL informed model while they are absent in the standard model with uniform strength distribution. Most of the mode II cracks, or shear micro-cracks, are not part of the main hydraulic fracture and occur in the near-tip and near-fracture areas. The position and occurrence of the shear micro-cracks is characterized as secondary effect which dissipates the hydraulic fracturing energy. Additionally, the shear micro-crack locations qualitatively resemble acoustic emission cloud of shear cracks frequently observed in hydraulic fracturing, and sometimes interpreted as re-activation of existing fractures. Clearly, our model does not contain pre-existing cracks and has continuous nature prior to fracturing. This observation is novel and interesting and is quantified in the paper. The shear particle contact forces field reveals significant relaxation compared to the model with uniform strength distribution.

  17. Fracture network of the Ferron Sandstone Member of the Mancos Shale, east-central Utah, USA

    USGS Publications Warehouse

    Condon, S.M.

    2003-01-01

    The fracture network at the outcrop of the Ferron Sandstone Member of the Mancos Shale was studied to gain an understanding of the tectonic history of the region and to contribute data to studies of gas and water transmissivity related to the occurrence and production of coal-bed methane. About 1900 fracture readings were made at 40 coal outcrops and 62 sandstone outcrops in the area from Willow Springs Wash in the south to Farnham dome in the north of the study area in east-central Utah.Two sets of regional, vertical to nearly vertical, systematic face cleats were identified in Ferron coals. A northwest-striking set trends at a mean azimuth of 321??, and a northeast-striking set has a mean azimuth of 55??. Cleats were observed in all coal outcrops examined and are closely spaced and commonly coated with thin films of iron oxide.Two sets of regional, systematic joint sets in sandstone were also identified and have mean azimuths of 321?? and 34??. The joints of each set are planar, long, and extend vertically to nearly vertically through multiple beds; the northeast-striking set is more prevalent than the northwest-striking set. In some places, joints of the northeast-striking set occur in closely spaced clusters, or joint zones, flanked by unjointed rock. Both sets are mineralized with iron oxide and calcite, and the northwest-striking set is commonly tightly cemented, which allowed the northeast-striking set to propagate across it. All cleats and joints of these sets are interpreted as opening-mode (mode I) fractures. Abutting relations indicate that the northwest-striking cleats and joints formed first and were later overprinted by the northeast-striking cleats and joints. Burial curves constructed for the Ferron indicate rapid initial burial after deposition. The Ferron reached a depth of 3000 ft (1000 m) within 5.2 million years (m.y.), and this is considered a minimum depth and time for development of cleats and joints. The Sevier orogeny produced southeast

  18. Analysis of some seismic expressions of Big Injun sandstone and its adjacent interval

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Xiangdong, Zou; Wilson, T.A.; Donaldson, A.C.

    1991-08-01

    The Big Injun sandstone is an important oil and gas reservoir in western West Virginia. The pre-Greenbrier unconformity has complicated correlations, and hydrocarbon explorationists commonly have misidentified the Big Injun in the absence of a regional stratigraphic study. Paleogeologic maps on this unconformity show the West Virginia dome, with the Price/Pocono units truncated resulting in pinch-outs of different sandstones against the overlying Big Lime (Greenbrier Limestone). Drillers have named the first sandstone below the Big Lime as Big Injun, and miscorrelated the real Big Injun with Squaw, upper Weir, and even the Berea sandstone. In this report, an 8-mi (13-km)more » seismic section extending from Kanawha to Clay counties was interpreted. The study area is near the pinch-out of the Big Injun sandstone. A stratigraphic cross section was constructed from gamma-ray logs for comparison with the seismic interpretation. The modeling and interpretation of the seismic section recognized the relief on the unconformity and the ability to determine facies changes, too. Both geophysical wireline and seismic data can be used for detailed stratigraphic analysis within the Granny Creek oil field of Clay and Roane countries.« less

  19. Mechanistic study of wettability alteration of oil-wet sandstone surface using different surfactants

    NASA Astrophysics Data System (ADS)

    Hou, Bao-feng; Wang, Ye-fei; Huang, Yong

    2015-03-01

    Different analytical methods including Fourier transform infrared (FTIR), atomic force microscopy (AFM), zeta potential measurements, contact angle measurements and spontaneous imbibition tests were utilized to make clear the mechanism for wettability alteration of oil-wet sandstone surface using different surfactants. Results show that among three types of surfactants including cationic surfactants, anionic surfactants and nonionic surfactants, the cationic surfactant CTAB demonstrates the best effect on the wettability alteration of oil-wet sandstone surface. The positively charged head groups of CTAB molecules and carboxylic acid groups from crude oil could interact to form ion pairs, which could be desorbed from the solid surface and solubilized into the micelle formed by CTAB. Thus, the water-wetness of the solid surface is improved. Nonionic surfactant TX-100 could be adsorbed on oil-wet sandstone surface through hydrogen bonds and hydrophobic interaction to alter the wettability of oil-wet solid surface. The wettability alteration of oil-wet sandstone surface using the anionic surfactant POE(1) is caused by hydrophobic interaction. Due to the electrostatic repulsion between the anionic surfactant and the negatively charged surface, POE(1) shows less effect on the wettability alteration of oil-wet sandstone surface.

  20. A new bee species that excavates sandstone nests.

    PubMed

    Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

    2016-09-12

    Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Influence of depositional environment on diagenesis in St. Peter sandstone, Michigan basin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lundgren, C.E. Jr.; Barnes, D.A.

    1989-03-01

    The Middle Ordovician St. Peter Sandstone in the Michigan basin was deposited in marine peritidal to storm-dominated, outer shelf depositional environments that evolved in a regionally significant transgressive pattern. The formation is bounded by carbonate and shaly clastic strata of the Prairie du Chien Group below and is transitional to condensed sequence clastics and carbonates of the Glenwood Formation above. Sedimentologic and petrographic analysis of conventional core from 25 wells suggests that reservoir quality in the formation is strongly dependent on a complex diagenetic history, especially the nature and subsequent dissolution of intergranular carbonate in the sandstone. Petrographic evidence indicatesmore » that porosity in the formation formed by dissolution of precursor dolomite of various origins and, locally, the formation of pore-filling authigenic clay (chlorite-illite). Authigenic clay is the incongruent dissolution product of dolomite, detrital K-feldspar, and, possibly, muscovite and results in diminished reservoir quality where abundant in the St. Peter Sandstone. Authigenic clay is volumetrically more significant in the upper portions of the formation and is associated with higher concentrations of detrital K-feldspar. Depositional facies controlled the distribution and types of intergranular carbonate (now dolomite) and detrital K-feldspar in the St. Peter Sandstone and hence reservoir quality; both components were more significant in storm-shelf sandstone facies.« less

  2. Inelastic compaction, dilation and hysteresis of sandstones under hydrostatic conditions

    NASA Astrophysics Data System (ADS)

    Shalev, Eyal; Lyakhovsky, Vladimir; Ougier-Simonin, Audrey; Hamiel, Yariv; Zhu, Wenlu

    2014-05-01

    Sandstones display non-linear and inelastic behaviour such as hysteresis when subjected to cyclic loading. We present three hydrostatic compaction experiments with multiple loading-unloading cycles on Berea and Darley Dale sandstones and explain their hysteretic behaviour using non-linear inelastic compaction and dilation. Each experiment included eight to nine loading-unloading cycles with increasing maximum pressure in each subsequent cycle. Different pressure-volumetric strain relations during loading and unloading were observed. During the first cycles, under relatively low pressures, not all of the volumetric strain is recovered at the end of each cycle whereas at the last cycles, under relatively high pressures, the strain is recovered and the pressure-volumetric strain hysteresis loops are closed. The observed pressure-volumetric strain relations are non-linear and the effective bulk modulus of the sandstones changes between cycles. Observations are modelled with two inelastic deformation processes: irreversible compaction caused by changes in grain packing and recoverable compaction associated with grain contact adhesion, frictional sliding on grains or frictional sliding on cracks. The irreversible compaction is suggested to reflect rearrangement of grains into a more compact mode as the maximum pressure increases. Our model describes the `inelastic compaction envelope' in which sandstone sample will follow during hydrostatic loading. Irreversible compaction occurs when pressure is greater than a threshold value defined by the `inelastic compaction envelope'.

  3. Diverse Grains in Mars Sandstone Target Big Arm

    NASA Image and Video Library

    2015-07-01

    This view of a sandstone target called "Big Arm" covers an area about 1.3 inches (33 millimeters) wide in detail that shows differing shapes and colors of sand grains in the stone. Three separate images taken by the Mars Hand Lens Imager (MAHLI) camera on NASA's Curiosity Mars rover, at different focus settings, were combined into this focus-merge view. The Big Arm target on lower Mount Sharp is at a location near "Marias Pass" where a mudstone bedrock is in contact with overlying sandstone bedrock. MAHLI recorded the component images on May 29, 2015, during the 999th Martian day, or sol, of Curiosity's work on Mars. The rounded shape of some grains visible here suggests they traveled long distances before becoming part of the sediment that later hardened into sandstone. Other grains are more angular and may have originated closer to the rock's current location. Lighter and darker grains may have different compositions. MAHLI was built by Malin Space Science Systems, San Diego. NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, manages the Mars Science Laboratory Project for the NASA Science Mission Directorate, Washington. http://photojournal.jpl.nasa.gov/catalog/PIA19677

  4. Fluvial-deltaic sedimentation and stratigraphy of the ferron sandstone

    USGS Publications Warehouse

    Anderson, P.B.; Chidsey, T.C.; Ryer, T.A.

    1997-01-01

    East-central Utah has world-class outcrops of dominantly fluvial-deltaic Turonian to Coniacian aged strata deposited in the Cretaceous foreland basin. The Ferron Sandstone Member of the Mancos Shale records the influences of both tidal and wave energy on fluvial-dominated deltas on the western margin of the Cretaceous western interior seaway. Revisions of the stratigraphy are proposed for the Ferron Sandstone. Facies representing a variety of environments of deposition are well exposed, including delta-front, strandline, marginal marine, and coastal-plain. Some of these facies are described in detail for use in petroleum reservoir characterization and include permeability structure.

  5. Research progress and harnessing method of soil and water loss in Pisha Sandstone region

    NASA Astrophysics Data System (ADS)

    Xiao, P. Q.; Yang, C. X.; Jing, C. R.

    2018-05-01

    Pisha Sandstone region is the most vulnerable and the most dramatic area of soil erosion, severe soil erosion on the ecological bases of China’s energy security constitutes a serious challenge. Research progress of soil erosion in pisha Sandstone region was reviewed based on the need of soil and water ecological construction in Pisha Sandstone region and harnessing the yellow river including soil erosion mechanism, soil erosion dynamic monitoring and soil erosion simulation assessments. Meanwhile, the latest progress of soil and water conservation measures was analyzed, and the existing problems and future harnessing measures of soil and water loss were discussed. This study is to explore the comprehensive management method and provide scientific theory for constructing soil and water conservation project in Pisha Sandstone region.

  6. A subtle diagenetic trap in the Cretaceous Glauconite Sandstone of Southwest Alberta

    USGS Publications Warehouse

    Meshri, I.D.; Comer, J.B.

    1990-01-01

    Despite the long history of research which documents many studies involving extensive diagenesis, there are a few examples of a fully documented diagenetic trap. In the context of this paper, a trap is a hydrocarbon-bearing reservoir with a seal; because a reservoir without a seal acts as a carrier bed. The difficulty in the proper documentation of diagenetic traps is often due to the lack of: (a) extensive field records on the perforation and production histories, which assist in providing the depth of separation between hydrocarbon production and non-hydrocarbon or water production; and (b) the simultaneous availability of core data from these intervals, which could be studied for the extent and nature of diagenesis. This paper provides documentation for the existence of a diagenetic trap, based on perforation depths, production histories and petrologic data from the cored intervals, in the context of the geologic and stratigraphic setting. Cores from 15 wells and SP logs from 45 wells were carefully correlated and the data on perforated intervals was also acquired. Extensive petrographic work on the collected cores led to the elucidation of a diagenetic trap that separates water overlying and updip from gas downdip. Amoco's Berrymore-Lobstick-Bigoray fields, located near the northeastern edge of the Alberta Basin, are prolific gas producers. The gas is produced from reservoir rock consisting of delta platform deposits formed by coalescing distributary mouth bars. The overlying rock unit is composed of younger distributary channels; although it has a good reservoir quality, it contains and produces water only. The total thickness of the upper, water-bearing and lower gas-bearing sandstone is about 40 ft. The diagenetic seal is composed of a zone 2 to 6 ft thick, located at the base of distributary channels. This zone is cemented with 20-30% ankerite cement, which formed the gas migration and is also relatively early compared to other cements formed in the water

  7. Potentiometric-surface map of the Wyodak-Anderson Coal Bed, Powder River Structural Basin, Wyoming, 1973-84

    USGS Publications Warehouse

    Daddow, Pamela B.

    1986-01-01

    Previous water level maps of shallow aquifers in the Powder River structural basin in Wyoming were based on water levels from wells completed in different stratigraphic intervals within thick sequences of sedimentary rocks. A potentiometric surface using water levels from a single aquifer had never been mapped throughout the basin. The sandstone aquifers in the Fort Union Formation of Paleocene age and the Wasatch Formation of Eocene age are discontinuous and lenticular, and do not extend even short distances. Coal aquifers are more continuous and the Wyodak-Anderson coal bed, in the Fort Union Formation, has been mapped in much of the Powder River structural basin in Wyoming. Water level altitudes in the Wyodak-Anderson coal bed and other stratigraphically equivalent coal beds were mapped to determine if they represent a continuous potentiometric surface in the Powder River structural basin. The potentiometric surface, except in the vicinity of the Wyodak mine east of Gillette, represents a premining condition as it was based on water level measurements made during 1973-84 that were not significantly affected by mining. The map was prepared in cooperation with the U.S. Bureau of Land Management. (Lantz-PTT)

  8. The provenance and chemical variation of sandstones associated with the Mid-continent Rift System, U.S.A.

    USGS Publications Warehouse

    Cullers, R.L.; Berendsen, P.

    1998-01-01

    Sandstones along the northern portion of the Precambrian Mid-continent Rift System (MRS) have been petrographically and chemically analyzed for major elements and a variety of trace elements, including the REE. After the initial extrusion of the abundant basalts along the MRS, dominantly volcaniclastic sandstones of the Oronto Group were deposited. These volcaniclastic sandstones are covered by quartzose and subarkosic sandstones of the Bayfield Group. Thus the sandstones of the Oronto Group were derived from previously extruded basalts, whereas, the sandstones of the Bayfield Group were derived from Precambrian granitic gneisses located on the rift flanks. The chemical variation of these sandstones closely reflects the changing detrital modes with time. The elemental composition of the sandstones confirms the source lithologies suggested by the mineralogy and clasts. The Oronto Group sandstones contain lower ratios of elements concentrated in silicic source rocks (La or Th) relative to elements concentrated in basic source rocks (Co, Cr, or Sc) than the Bayfield Group. Also, the average size of the negative Eu anomaly of the sandstones of the Oronto Group is significantly less (Eu/Eu* mean ?? standard deviation = 0.79 ?? 0.13) than that of the Bayfield Group (mean + standard deviation = 0.57 ?? 0.09), also suggesting a more basic source for the former than the latter. Mixing models of elemental ratios give added insight as to the evolution of the rift. These models suggest that the volcanistic sandstones of the lower portion of the Oronto Group are derived from about 80 to 90 percent basalt and 10 to 20 percent granitoids. The rest of the Oronto Group and the lower to middle portion of the Bayfield Group could have formed by mixing of about 30 to 60 percent basalt and 40 to 70 percent granitoids. The upper portion of the Bayfield Group is likely derived from 80 to 100 percent granitoids and zero to 20 percent basalt.

  9. Initiation and propagation of mixed mode fractures in granite and sandstone

    NASA Astrophysics Data System (ADS)

    Rück, Marc; Rahner, Roman; Sone, Hiroki; Dresen, Georg

    2017-10-01

    We investigate mixed mode fracture initiation and propagation in experimentally deformed granite and sandstone. We performed a series of asymmetric loading tests to induce fractures in cylindrical specimens at confining pressures up to 20 MPa. Loading was controlled using acoustic emission (AE) feedback control, which allows studying quasi-static fracture propagation for several hours. Location of acoustic emissions reveals distinct differences in spatial-temporal fracture evolution between granite and sandstone samples. Before reaching peak stress in experiments performed on granite, axial fractures initiate first at the edge of the indenter and then propagate through the entire sample. Secondary inclined fractures develop during softening of the sample. In sandstone, inclined shear fractures nucleate at peak stress and propagate through the specimen. AE source type analysis shows complex fracturing in both materials with pore collapse contributing significantly to fracture growth in sandstone samples. We compare the experimental results with numerical models to analyze stress distribution and energy release rate per unit crack surface area in the samples at different stages during fracture growth. We thereby show that for both rock types the energy release rate increases approximately linearly during fracture propagation. The study illuminates how different material properties modify fracture initiation direction under similar loading conditions.

  10. Analysis of deformation bands in the Aztec Sandstone, Valley of Fire State Park, Nevada

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hill, R.E.

    1993-04-01

    This research concerns two types of deformation structures, deformation bands and low-angle slip surfaces, that occur in the Aztec Sandstone in the Valley of Fire State Park, Nevada. Deformation bands were analyzed by mapping and describing over 500 of the structures on a bedding surface of about 560 square meters. Deformation bands are narrow zones of reduced porosity which form resistant ribs in the sandstone. Three sets of deformation bands are present at the study site (type 1,2, and 3). Type 1 and 2 bands are interpreted as coeval and form a conjugate set with a dihedral angle of 90more » degrees. These sets are usually composed of multiple bands. A third set is interpreted to be subsidiary to the older set, and intersections angles with the earlier formed sets are approximately 45 degrees. In contrast with the older sets, the third set is nearly always a single band which is sinuous or jagged along its length. All three sets of deformation bands are crosscut and sometimes offset by low-angle slip surfaces. These faults have reverse dip slip displacement and locally have mullions developed. Displacements indicate eastward movement of the hanging wall which is consistent with the inferred movements of major Mesozoic thrust faults in the vicinity. The change of deformation style from deformation bands to low-angle slip surfaces may document a change in the stress regime. Paleostress interpretation of the deformation band geometry indicates the intermediate stress axis is vertical. The low-angle slip surfaces indicate the least compressive stress axis is vertical. This possible change in stress axes may be the result of increasing pore pressure associated with tectonic loading from emplacement of the Muddy Mountain thrust.« less

  11. Correlative multiple porosimetries for reservoir sandstones with adoption of a new reference-sample-guided computed-tomographic method

    PubMed Central

    Jin, Jae Hwa; Kim, Junho; Lee, Jeong-Yil; Oh, Young Min

    2016-01-01

    One of the main interests in petroleum geology and reservoir engineering is to quantify the porosity of reservoir beds as accurately as possible. A variety of direct measurements, including methods of mercury intrusion, helium injection and petrographic image analysis, have been developed; however, their application frequently yields equivocal results because these methods are different in theoretical bases, means of measurement, and causes of measurement errors. Here, we present a set of porosities measured in Berea Sandstone samples by the multiple methods, in particular with adoption of a new method using computed tomography and reference samples. The multiple porosimetric data show a marked correlativeness among different methods, suggesting that these methods are compatible with each other. The new method of reference-sample-guided computed tomography is more effective than the previous methods when the accompanied merits such as experimental conveniences are taken into account. PMID:27445105

  12. Interpretation of massive sandstones in ephemeral fluvial settings: A case study from the Upper Candelária Sequence (Upper Triassic, Paraná Basin, Brazil)

    NASA Astrophysics Data System (ADS)

    Horn, Bruno Ludovico Dihl; Goldberg, Karin; Schultz, Cesar Leandro

    2018-01-01

    Ephemeral rivers display a wide range of upper- and lower-flow regime structures due to great flow-velocity changes during the floods. The development of flow structures in these setting is yet to be understood, especially in the formation of thick, massive sandstones. The Upper Triassic of Southern Gondwana was marked by a climate with great seasonal changes, yet there is no description of river systems with seasonal characteristics in Southern Gondwana. This work aims to characterize a ephemeral alluvial system of the Upper Triassic of the Paraná Basin. The characteristics of the deposits are discussed in terms of depositional processes through comparison with similar deposits from literature, flow characteristics and depositional signatures compared to flume experiments. The alluvial system is divided in four facies associations: (1) channels with wanning fill, characterized by low width/thickness ratio, tabular bodies, scour-and-fill structures with upper- and lower-flow regime bedforms; (2) channels with massive fill, characterized by low w/t ratio, sheet-like bodies, scour-and-fill structures with massive sandstones; (3) proximal sheetfloods, characterized by moderate w/t ratio, sheet-like bodies with upper- and lower-flow regime bedforms and (4) distal sheetfloods, characterized by high w/t ratio, sheet-like bodies with lower-flow regime bedforms. Evidence for the seasonal reactivation of the riverine system includes the scarcity of well-developed macroforms and presence of in-channel mudstones, thick intraformational conglomerates, and the occurrence of well- and poorly-preserved vertebrate bones in the same beds. The predominantly massive sandstones indicate deposition from a hyperconcentrated flow during abrupt changes in flow speed, caused by de-confinement or channel avulsion, whereas turbulent portions of the flow formed the upper- and lower-flow regime bedforms after the deposition of the massive layers. The upper portion of the Candelária Sequence

  13. Red Fork and lower Skinner sandstones in northwest Tecumseh field, Pottawatomie County, Oklahoma

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Dale, T.B.

    1987-08-01

    The Northwest Tecumseh field, discovered in 1978, produces from the Pennsylvanian Skinner and Red Fork sandstones at 4800 ft. The 50 wells had produced 6.4 million bbl of oil and 20.8 bcf of gas through 1986. The field is 4.5 mi long, 3/4 mi wide, and the vertical section contains up to 132 ft of sandstone with greater than 10% porosity. These stacked, interconnected north-northeast-trending, channel-fill sandstones are part of a much larger fluvial/distributary system. These channels flowed to the north and cut down into underlying, fossiliferous, carbonate-bearing marine shale. A pre-Pennsylvanian structural low, trending north-northeast, existed in the southernmore » half of the field and created a predisposition for the channel trend which continued through Red Fork and Skinner deposition. The north-northeast-trending sandstone complex, parallel with present-day regional structural strike, provides the excellent configuration for this efficient stratigraphic trap. The northern end of the field is marked by bifurcation of the channel complex and by the crosscutting of a younger clay-filled channel. Despite the lenticularity of the sandstone sequence, there appears to be a uniform gas-oil contact and minor southwestward tilt of the oil-water contact in the south part of the pool. The primary reservoir energy is provided by a dissolved gas drive, with some assistance from the 60-ft gas cap. The vertical oil column is 80 ft. These reservoir sandstones are fine-grained quartzarenites, and the dissolution of ferrodolomite has increased porosities up to 21%. Kaolinite is the predominant clay mineral and has a tendency to migrate and reduce permeability during production.« less

  14. Depositional systems and diagenesis of Travis Peak tight gas sandstone reservoirs, Sabine Uplift Area, Texas

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fracasso, M.A.; Dutton, S.P.; Finley, R.J.

    The Travis Peak formation (lower Cretaceous) in the eastern East Texas basin is a fluvio-deltaic depositional system divided into large-scale facies packages: a middle sandstone-rich fluvial and delta-plain sequence that is gradationally overlain and underlain by a marine-influenced delta-fringe zone with a higher mudstone content. Domes and structural terraces on the west flank of the Sabine Uplift influenced deposition of Travis Peak sediments, and most Travis Peak gas production in this area is from thin sandstones (<25 ft(<7.6 m) thick) in the upper delta-fringe facies. The trapping mechanism is stratigraphic pinch-out of sandstones or porosity zones within sandstone, or both,more » on the flanks of structures. Detailed mapping of producing sandstone sequences in the uppermost upper delta-fringe on the western flank of the Bethany structure has delineated fluvial channelways, distributary or tidal channels, and barrier of distributary-mouth bars. Most Travis Peak gas production in the Bethany West area is from the bases of channel sandstones in a marine-influenced facies belt. Travis Peak sandstones in the eastern East Texas basin have undergone a complex series of diagenetic modifications. Precipitation of authigenic quartz, ankerite, dolomite, illite, and chlorite and the introduction of reservoir bitumen were the most important causes of occlusion of primary porosity and reduction of permeability. Permeability decreases with depth in the Travis Peak, which suggests that the diagenetic processes that caused extensive cementation and resultant low permeability throughout most of the formation operated less completely on sediments deposited near the top of the succession.« less

  15. Factors controlling reservoir quality in tertiary sandstones and their significance to geopressured geothermal production. Annual report, May 1, 1979-May 31, 1980

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Loucks, R.G.; Richmann, D.L.; Milliken, K.L.

    1980-07-01

    Differing extents of diagenetic modification is the factor primarily responsible for contrasting regional reservoir quality of Tertiary sandstones from the Upper and Lower Texas Gulf Coast. Detailed comparison of Frio sandstones from the Chocolate Bayou/Danbury Dome area, Brazoria County, and Vicksburg sandstones from the McAllen Ranch Field area, Hidalgo County, reveals that extent of diagenetic modification is most strongly influenced by (1) detrital mineralogy and (2) regional geothermal gradients. Vicksburg sandstones from the McAllen Ranch Field area are less stable, chemically and mechanically, than Frio sandstones from the Chocolate Bayou/Danbury dome area. Vicksburg sandstones are mineralogically immature and contain greatermore » proportions of feldspars and rock fragments than do Frio sandstones. Thr reactive detrital assemblage of Vicksubrg sandstones is highly susceptible to diagenetic modification. Susceptibility is enhanced by higher than normal geothermal gradients in the McAllen Ranch Field area. Thus, consolidation of Vicksburg sandstones began at shallower depth of burial and precipitation of authigenic phases (especially calcite) was more pervasive than in Frio sandstones. Moreover, the late-stage episode of ferroan calcite precipitation that occluded most secondary porosity in Vicksburg sandstones did not occur significantly in Frio sandstones. Therefore, regional reservoir quality of Frio sandstones from Brazoria County is far better than that characterizing Vicksburg sandstones from Hidalgo County, especially at depths suitable for geopressured geothermal energy production.« less

  16. Acoustic bed velocity and bed load dynamics in a large sand bed river

    USGS Publications Warehouse

    Gaeuman, D.; Jacobson, R.B.

    2006-01-01

    Development of a practical technology for rapid quantification of bed load transport in large rivers would represent a revolutionary advance for sediment monitoring and the investigation of fluvial dynamics. Measurement of bed load motion with acoustic Doppler current profiles (ADCPs) has emerged as a promising approach for evaluating bed load transport. However, a better understanding of how ADCP data relate to conditions near the stream bed is necessary to make the method practical for quantitative applications. In this paper, we discuss the response of ADCP bed velocity measurements, defined as the near-bed sediment velocity detected by the instrument's bottom-tracking feature, to changing sediment-transporting conditions in the lower Missouri River. Bed velocity represents a weighted average of backscatter from moving bed load particles and spectral reflections from the immobile bed. The ratio of bed velocity to mean bed load particle velocity depends on the concentration of the particles moving in the bed load layer, the bed load layer thickness, and the backscatter strength from a unit area of moving particles relative to the echo strength from a unit area of unobstructed bed. A model based on existing bed load transport theory predicted measured bed velocities from hydraulic and grain size measurements with reasonable success. Bed velocities become more variable and increase more rapidly with shear stress when the transport stage, defined as the ratio of skin friction to the critical shear stress for particle entrainment, exceeds a threshold of about 17. This transition in bed velocity response appears to be associated with the appearance of longer, flatter bed forms at high transport stages.

  17. Experimental deformation in sandstone, carbonates and quartz aggregate

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cheung, Cecilia See Nga

    2015-05-01

    The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstratemore » that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with

  18. Hydropressure tongues within regionally geopressured lower Tuscaloosa sandstone, Tuscaloosa trend, Louisiana

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McCulloh, R.P.; Purcell, M.D.

    1983-01-01

    A regional study of the Tuscaloosa Formation in Louisiana, undertaken to assess geopressured-geothermal potential, revealed lobate, downdip extensions of the hydropressured zone in lower Tuscaloosa massive sandstone facies below the regional top of geopressure. Normal pressure zones within geopressured section were identified by drilling mud weights less than 13 pounds per gallon on electric logs of massive lower Tuscaloosa sandstone, and cross sections demonstrated updip continuity of these zones with the regional hydropressured zone. These hydropressure tongues are permitted by the anomalously high permeabilities reportd from the deep Tuscaloosa trend which have been attributed to both primary and secondary porosity.more » The hydropressure tongues correspond with lobes of thick net sandstone, principally in Pointe Coupee, East Feliciana, East Baton Rouge, and Livingston Parishes in the central Tuscaloosa trend. Limited control suggests at least one hydropressure tongue in the Chandeleur Sound area to the east.« less

  19. Nodules of Cemented Sand Grains Within Martian Sandstone

    NASA Image and Video Library

    2016-03-11

    This view from NASA Curiosity shows nodules exposed in sandstone that is part of the Stimson geological unit on Mount Sharp, Mars. The nodules can be seen to consist of grains of sand cemented together.

  20. Biologically-initiated rock crust on sandstone: Mechanical and hydraulic properties and resistance to erosion

    NASA Astrophysics Data System (ADS)

    Slavík, Martin; Bruthans, Jiří; Filippi, Michal; Schweigstillová, Jana; Falteisek, Lukáš; Řihošek, Jaroslav

    2017-02-01

    Biocolonization on sandstone surfaces is known to play an important role in rock disintegration, yet it sometimes also aids in the protection of the underlying materials from rapid erosion. There have been few studies comparing the mechanical and/or hydraulic properties of the BIRC (Biologically-Initiated Rock Crust) with its subsurface. As a result, the overall effects of the BIRC are not yet well understood. The objective of the present study was to briefly characterize the BIRC from both the mineralogical and biological points of view, and especially to quantify the effect of the BIRC upon the mechanical and hydraulic properties of friable sandstone. The mineralogical investigation of a well-developed BIRC showed that its surface is enriched in kaolinite and clay- to silt-sized quartz particles. Total organic carbon increases with the age of the BIRC. Based on DNA sequencing and microscopy, the BIRC is formed by various fungi, including components of lichens and green algae. Using the method of drilling resistance, by measuring tensile strength, and based on water jet testing, it was determined that a BIRC is up to 12 times less erodible and has 3-35 times higher tensile strength than the subsurface friable sandstone. Saturated hydraulic conductivity of the studied BIRC is 15-300 times lower than the subsurface, and was measured to also decrease in capillary water absorption (2-33 times). Water-vapor diffusion is not significantly influenced by the presence of the BIRC. The BIRC thus forms a hardened surface which protects the underlying material from rain and flowing water erosion, and considerably modifies the sandstone's hydraulic properties. Exposing the material to calcination (550 °C), and experiments with the enzyme zymolyase indicated that a major contribution to the surface hardening is provided by organic matter. In firmer sandstones, the BIRC may still considerably decrease the rate of weathering, as it is capable of providing cohesion to strongly

  1. Sandstone: secular trends in lithology in southwestern montana.

    PubMed

    McLane, M

    1972-11-03

    Long-term secular trends in the composition and texture of sandstones in southwestern Montana reflect changing provenance and depositional environment, which in turn reflect changing tectonic patterns in the Cordilleran mobile belt just to the west.

  2. Geohydrology of the Navajo sandstone in western Kane, southwestern Garfield, and southeastern Iron counties, Utah

    USGS Publications Warehouse

    Freethey, G.W.

    1988-01-01

    The upper Navajo and Lamb Point aquifers in the Navajo Sandstone are the principal source of water for the city of Kanab, irrigation, stock, and for rural homes in the study area. Well logs and outcrop descriptions indicate the Navajo Sandstone consists of the Lamb Point Tongue and an unnamed upper member that are separated by the Tenney Canyon Tongue of the Kayenta Formation. The main Kayenta Formation underlies the Lamb Point Tongue. The Lamb Point Tongue and the upper member of the Navajo Sandstone are saturated and hydraulically connected through the Tenney Canyon Tongue. Available data indicate that precipitation percolates to the groundwater reservoir where the Navajo Sandstone crops out. Estimates of the rate of recharge at the outcrop range from 0.1 to as much as 2.8 in/yr. Water level data indicate that water moves from the upper member of the Navajo Sandstone, through the Tenney Canyon Tongue, and into the Lamb Point Tongue. Lateral flow is generally from the outcrop areas toward the incised canyons formed by tributaries of Kanab Creek and Johnson Wash. Direction and rate of groundwater movement and the location and character of the natural hydrologic boundaries in the northern part of the area where the Navajo Sandstone is buried cannot be determined conclusively without additional water level data. (Author 's abstract)

  3. Deformation of Reservoir Sandstones by Elastic versus Inelastic Deformation Mechanisms

    NASA Astrophysics Data System (ADS)

    Pijnenburg, R.; Verberne, B. A.; Hangx, S.; Spiers, C. J.

    2016-12-01

    Hydrocarbon or groundwater production from sandstone reservoirs can result in surface subsidence and induced seismicity. Subsidence results from combined elastic and inelastic compaction of the reservoir due to a change in the effective stress state upon fluid extraction. The magnitude of elastic compaction can be accurately described using poroelasticity theory. However inelastic or time-dependent compaction is poorly constrained. Specifically, the underlying microphysical processes controlling sandstone compaction remain poorly understood. We use sandstones recovered by the field operator (NAM) from the Slochteren gas reservoir (Groningen, NE Netherlands) to study the importance of elastic versus inelastic deformation processes upon simulated pore pressure depletion. We conducted conventional triaxial tests under true in-situ conditions of pressure and temperature. To investigate the effect of applied differential stress (σ1 - σ3 = 0 - 50 MPa) and initial sample porosity (φi = 12 - 24%) on instantaneous and time-dependent inelastic deformation, we imposed multiple stages of axial loading and relaxation. The results show that inelastic strain develops at all stages of loading, and that its magnitude increases with increasing value of differential stress and initial porosity. The stress sensitivity of the axial creep strain rate and microstructural evidence suggest that inelastic compaction is controlled by a combination of intergranular slip and intragranular cracking. Intragranular cracking is shown to be more pervasive with increasing values of initial porosity. The results are consistent with a conceptual microphysical model, involving deformation by poro-elasticity combined with intergranular sliding and grain contact failure. This model aims to predict sandstone deformation behavior for a wide range of stress conditions.

  4. Petrology and reservoir quality of the Gaikema Sandstone: Initial impressions

    USGS Publications Warehouse

    Helmold, Kenneth P.; Stanley, Richard G.

    2015-01-01

    The Division of Geological & Geophysical Surveys (DGGS) and Division of Oil & Gas (DOG) are currently conducting a study of the hydrocarbon potential of Cook Inlet basin (LePain and others, 2011). The Tertiary stratigraphic section of the basin includes coal-bearing units that are prolific gas reservoirs, particularly the Neogene sandstones. The Paleogene sandstones are locally prolific oil reservoirs that are sourced largely from the underlying Middle Jurassic Tuxedni Group. Several large structures act as hydrocarbon traps and the possibility exists for stratigraphic traps although this potential has not been fully exploited. As part of this study a significant number of Tertiary sandstones from the basin have been already collected and analyzed (Helmold and others, 2013). Recent field programs have shifted attention to the Mesozoic stratigraphic section to ascertain whether it contains potential hydrocarbon reservoirs. During the 2013 Cook Inlet field season, two days were spent on the Iniskin Peninsula examining outcrops of the Middle Jurassic Gaikema Sandstone along the south shore of Chinitna Bay (fig. 7-1). A stratigraphic section approximately 34 m in thickness was measured and a detailed description was initiated (Stanley and others, 2015), but due to deteriorating weather it was not possible to complete the description. During the 2014 field season two additional days were spent completing work on the Gaikema section. Analyses of thin sections from six of the samples collected in 2013 are available for incorporation in this report (table 7-1). Data from samples collected during the 2014 field season will be included in future reports.

  5. Tephrochronology of Bed II, Olduvai Gorge, Tanzania, and placement of the Oldowan-Acheulean transition.

    PubMed

    McHenry, Lindsay J; Stanistreet, Ian G

    2018-04-12

    Tuffaceous marker beds, derived from volcanic products from the Ngorongoro Volcanic Highlands, help define a stratigraphic framework for the world-renowned fossil and stone tool record exposed at Olduvai Gorge, Tanzania. However, previous efforts to constrain this tuff record, especially for Olduvai Bed II, have been limited because of erosion, contamination, reworking, and the alteration of volcanic glass under saline-alkaline conditions. This paper applies previously defined geochemical and mineralogical "fingerprints" for several major Bed II marker tuffs, based on glass (where available) and phenocrysts more resistant to alteration (feldspar, hornblende, augite, and titanomagnetite), to tuffs from stratigraphic sections in the Olduvai Junction Area, including previously and recently excavated Acheulean and Oldowan sites (HWK EE (Locality (Loc) 42), EF-HR (Loc 12a), FLK (Loc 45), and MNK (Loc 88)). The Middle Bed II Bird Print Tuff (BPT) is found to be more compositionally variable than previously reported but is still valuable as a stratigraphic marker over short distances. The confirmation of blocks of Tuff IID in conglomerate helps constrain Upper Bed II stratigraphy at sites where in-situ tuffs are absent. This paper also compiles the results of published geochronological research, providing stratigraphic context and updating previously reported dates using a consistent 40 Ar/ 39 Ar reference standard age. The results of this work support the following paleoanthropologically relevant conclusions: 1) the early Acheulean site EF-HR (Loc 12a) is situated above the level of Hay's Tuff IIC, and thus sits in Upper rather than Middle Bed II, (2) the HWK EE (Loc 42) Oldowan site is constrained between Tuff IIA and Tuff IIB, just above the boundary between Lower and Middle Bed II, and 3) the Acheulean site at FLK W most likely lies within the Middle Augitic Sandstone, above Tuff IIB, similar to the placements by Leakey and Hay for the earliest Acheulean at Olduvai

  6. A multi-tracer study in the Hutton Sandstone aquifer, Australia: How "wrong ages" give us deeper insights into aquifer structure and effective deep recharge to a double porosity system

    NASA Astrophysics Data System (ADS)

    Suckow, Axel; Taylor, Andrew; Davies, Phil; Leaney, Fred

    2017-04-01

    Depressurisation of coal seams in the Walloon Coal Measures in Queensland, Australia, may influence aquifers both over- and underlying the formation. The Gubberamunda Sandstone aquifer, which overlies the Walloon Coal Measures, is the starting point of the Great Artesian Basin (GAB) flow system and has been the focus of numerous recharge studies. In comparison, the Hutton Sandstone aquifer, which underlies the Walloon Coal Measures, has received much less attention. This aquifer however, is the main supply of stock water for the beef industry in the area. A multi-environmental tracer study of the Hutton Sandstone aquifer was undertaken at the Mimosa Syncline and was complemented by a few samples taken from the underlying Precipice Sandstone aquifer. This multi-tracer study (comprising 18O, 2H, 3H, CFCs, SF6, 14C, 36Cl, and 4He) demonstrated that the Hutton Sandstone aquifer behaves as a double porosity system. At the regional scale, the system features a relatively small fraction of conductive rock within a fairly large fraction of low permeability rock. Tracer migration therefore occurs mainly by advection in the conductive fraction and mainly by diffusion in the low-permeability fraction of the aquifer. Groundwater flow velocities, derived from exponential decrease of 14C and 36Cl concentrations with distance, differ by a factor of ten and therefore do not indicate the real groundwater flow velocity. However, accounting for a double porosity interpretation of the tracer data leads to a single groundwater flow velocity that is consistent with all observed data. Advective velocity in this double porosity model differs from face value flow velocities derived from 14C and 36Cl by a factor of 4 and 40 respectively. As a consequence of this interpretation, the deeper groundwater flow system of the Hutton Sandstone aquifer is estimated to receive only 3% of the recharge previously estimated using the Chloride Mass Balance approach at the intake beds. The other 97% is

  7. Diagenetic controls on reservoir heterogeneity in St. Peter Sandstone, deep Michigan basin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Barnes, D.A.; Turmelle, T.M.; Adam, R.

    1989-03-01

    The St. Peter Sandstone is a highly productive gas and condensate reservoir throughout the central part of the Michigan basin. Production occurs in several intervals: a laterally continuous zone at the top of the formation typified in the Woodville, Falmouth, and Rose City fields and less continuous intervals lower in the formation typified in the Ruwe Gulf zone of the Reed City field. Porosity is not limited to hydrocarbon productive zones, however. Diagenesis has dramatically modified primary mineralogy and textures in the formation. Dominant diagenetic components are quartz, dolomite, and clay authigenic cements, extensive chemical compaction, and pervasive mineral leaching.more » Their model for sandstone diagenesis is consistent throughout the basin. Variation in the significance of these diagenetic components is strongly templated by stratigraphically predictable facies variations within the St. Peter Sandstone.« less

  8. Experimental and Numerical Investigations on Strength and Deformation Behavior of Cataclastic Sandstone

    NASA Astrophysics Data System (ADS)

    Zhang, Y.; Shao, J. F.; Xu, W. Y.; Zhao, H. B.; Wang, W.

    2015-05-01

    This work is devoted to characterization of the deformation and strength properties of cataclastic sandstones. Before conducting mechanical tests, the physical properties were first examined. These sandstones are characterized by a loose damaged microstructure and poorly cemented contacts. Then, a series of mechanical tests including hydrostatic, uniaxial, and triaxial compression tests were performed to study the mechanical strength and deformation of the sandstones. The results obtained show nonlinear stress-strain responses. The initial microcracks are closed at hydrostatic stress of 2.6 MPa, and the uniaxial compressive strength is about 0.98 MPa. Under triaxial compression, there is a clear transition from volumetric compressibility to dilatancy and a strong dependency on confining pressure. Based on the experimental evidence, an elastoplastic model is proposed using a linear yield function and a nonassociated plastic potential. There is good agreement between numerical results and experimental data.

  9. Coupled hydrology and biogeochemistry of Paleocene–Eocene coal beds, northern Gulf of Mexico

    USGS Publications Warehouse

    McIntosh, Jennifer C.; Warwick, Peter D.; Martini, Anna M.; Osborn, Stephen G.

    2010-01-01

    Thirty-six formation waters, gas, and microbial samples were collected and analyzed from natural gas and oil wells producing from the Paleocene to Eocene Wilcox Group coal beds and adjacent sandstones in north-central Louisiana, USA, to investigate the role hydrology plays on the generation and distribution of microbial methane. Major ion chemistry and Cl−Br relations of Wilcox Group formation waters suggest mixing of freshwater with halite-derived brines. High alkalinities (up to 47.8 meq/L), no detectable SO4, and elevated δ13C values of dissolved inorganic carbon (up to 20.5‰ Vienna Peedee belemnite [VPDB]) and CO2 (up to 17.67‰ VPDB) in the Wilcox Group coals and adjacent sandstones indicate the dominance of microbial methanogenesis. The δ13C and δD values of CH4, and carbon isotope fractionation of CO2 and CH4, suggest CO2 reduction is the major methanogenic pathway. Geochemical indicators for methanogenesis drop off significantly at chloride concentrations above ∼1.7 mol/L, suggesting that high salinities inhibit microbial activity at depths greater than ∼1.6 km. Formation waters in the Wilcox Group contain up to 1.6% modern carbon (A14C) to at least 1690 m depth; the covariance of δD values of co-produced H2O and CH4 indicate that the microbial methane was generated in situ with these Late Pleistocene or younger waters. The most enriched carbon isotope values for dissolved inorganic carbon (DIC) and CO2, and highest alkalinities, were detected in Wilcox Group sandstone reservoirs that were CO2 flooded in the 1980s for enhanced oil recovery, leading to the intriguing hypothesis that CO2 sequestration may actually enhance methanogenesis in organic-rich formations.

  10. Numerical simulation of multi-dimensional NMR response in tight sandstone

    NASA Astrophysics Data System (ADS)

    Guo, Jiangfeng; Xie, Ranhong; Zou, Youlong; Ding, Yejiao

    2016-06-01

    Conventional logging methods have limitations in the evaluation of tight sandstone reservoirs. The multi-dimensional nuclear magnetic resonance (NMR) logging method has the advantage that it can simultaneously measure transverse relaxation time (T 2), longitudinal relaxation time (T 1) and diffusion coefficient (D). In this paper, we simulate NMR measurements of tight sandstone with different wettability and saturations by the random walk method and obtain the magnetization decays of Carr-Purcell-Meiboom-Gill pulse sequences with different wait times (TW) and echo spacings (TE) under a magnetic field gradient, resulting in D-T 2-T 1 maps by the multiple echo trains joint inversion method. We also study the effects of wettability, saturation, signal-to-noise ratio (SNR) of data and restricted diffusion on the D-T 2-T 1 maps in tight sandstone. The results show that with decreasing wetting fluid saturation, the surface relaxation rate of the wetting fluid gradually increases and the restricted diffusion phenomenon becomes more and more obvious, which leads to the wetting fluid signal moving along the direction of short relaxation and the direction of the diffusion coefficient decreasing in D-T 2-T 1 maps. Meanwhile, the non-wetting fluid position in D-T 2-T 1 maps does not change with saturation variation. With decreasing SNR, the ability to identify water and oil signals based on NMR maps gradually decreases. The wetting fluid D-T 1 and D-T 2 correlations in NMR diffusion-relaxation maps of tight sandstone are obtained through expanding the wetting fluid restricted diffusion models, and are further applied to recognize the wetting fluid in simulated D-T 2 maps and D-T 1 maps.

  11. Architectural evidence of dune collapse in the Navajo Sandstone, Zion National Park, Utah

    NASA Astrophysics Data System (ADS)

    Ford, Colby; Bryant, Gerald; Nick, Kevin E.

    2016-10-01

    The Canyon Overlook Trail of Zion National Park follows an outcrop of Navajo Sandstone, which displays a uniquely well-exposed assemblage of features associated with failure of the lee face of a large eolian dune, and run-out over an expanse of interdune sediments downwind of that bedform. Exposed features include dramatic folds in the interdune succession and a stacked series of thrust sheets incorporating both interdune and overlying dune deposits. Thrust surfaces display consistent strikes, parallel to those of undeformed foresets, and incorporate zones of brittle failure and fluid deformation, including folds overturned in the direction of foreset dip. These features correspond to predictions made by a previous researcher's model of dune collapse, formulated from less fortuitously exposed architectures in the Navajo Sandstone. Unlike the previous model, however, this site preserves distinct indications that the bulk of deformed material accumulated above the level of the contemporary interdune surface, in an aggradational succession. Paleotopographic reconstruction, based on preserved facies relationships at this site, indicates the presence of a large dune, partially encroached upon a well-developed wet interdune succession, made up of two half-meter carbonate mud layers, separated by a meter of medium-grained sand. Trapping of pore water pressure between these mud layers during liquefaction reduced shear strength in this interval, facilitating the collapse of the lee face of the upwind dune into the interdune area, and transmitted resultant shear forces to distal portions of the interdune expanse, in the shallow subsurface. Shear failure developed along bedding planes in the horizontally laminated carbonate muds, which provided both lubrication of the shear surfaces and structural support for the preservation of coherent thrust sheets during production of an imbricated succession of shear zones in the toe portion of the slump. Individual shear surfaces

  12. Multielement statistical evidence for uraniferous hydrothermal activity in sandstones overlying the Phoenix uranium deposit, Athabasca Basin, Canada

    NASA Astrophysics Data System (ADS)

    Chen, Shishi; Hattori, Keiko; Grunsky, Eric C.

    2018-04-01

    The Phoenix U deposit, with indicated resources of 70.2 M lb U3O8, occurs along the unconformity between the Proterozoic Athabasca Group sandstones and the crystalline basement rocks. Principal component analysis (PCA) is applied to the compositions of sandstones overlying the deposit. Among PCs, PC1 accounts for the largest variability of U and shows a positive association of U with rare earth elements (REEs) + Y + Cu + B + Na + Mg + Ni + Be. The evidence suggests that U was dispersed into sandstones together with these elements during the uraniferous hydrothermal activity. Uranium shows an inverse association with Zr, Hf, Th, Fe, and Ti. Since they are common in detrital heavy minerals, such heavy minerals are not the major host of U. The elements positively associated with U are high in concentrations above the deposit, forming a "chimney-like" or "hump-like" distribution in a vertical section. Their enrichment patterns are explained by the ascent of basement fluids through faults to sandstones and the circulation of basinal fluids around the deposit. The Pb isotope compositions of whole rocks are similar to expected values calculated from the concentrations of U, Th, and Pb except for sandstones close to the deposit. The data suggest that in situ decay of U and Th is responsible for the Pb isotope compositions of most sandstones and that highly radiogenic Pb dispersed from the deposit to the proximal sandstones long after the mineralization. This secondary dispersion is captured in PC8, which has low eigenvalue. The data suggests that the secondary dispersion has minor effect on the overall lithogeochemistry of sandstones.

  13. Controls on the variability of net infiltration to desert sandstone

    USGS Publications Warehouse

    Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

    2007-01-01

    As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

  14. Sandstone type uranium deposits in the Ordos Basin, Northwest China: A case study and an overview

    NASA Astrophysics Data System (ADS)

    Akhtar, Shamim; Yang, Xiaoyong; Pirajno, Franco

    2017-09-01

    This paper provides a comprehensive review on studies of sandstone type uranium deposits in the Ordos Basin, Northwest China. As the second largest sedimentary basin, the Ordos Basin has great potential for targeting sandstone type U mineralization. The newly found and explored Dongsheng and Diantou sandstone type uranium deposits are hosted in the Middle Jurassic Zhilou Formation. A large number of investigations have been conducted to trace the source rock compositions and relationship between lithic subarkose sandstone host rock and uranium mineralization. An optical microscopy study reveals two types of alteration associated with the U mineralization: chloritization and sericitization. Some unusual mineral structures, with compositional similarity to coffinite, have been identified in a secondary pyrite by SEM These mineral phases are proposed to be of bacterial origin, following high resolution mapping of uranium minerals and trace element determinations in situ. Moreover, geochemical studies of REE and trace elements constrained the mechanism of uranium enrichment, displaying LREE enrichment relative to HREE. Trace elements such as Pb, Mo and Ba have a direct relationship with uranium enrichment and can be used as index for mineralization. The source of uranium ore forming fluids and related geological processes have been studied using H, O and C isotope systematics of fluid inclusions in quartz veins and the calcite cement of sandstone rocks hosting U mineralization. Both H and O isotopic compositions of fluid inclusions reveal that ore forming fluids are a mixture of meteoric water and magmatic water. The C and S isotopes of the cementing material of sandstone suggest organic origin and bacterial sulfate reduction (BSR), providing an important clue for U mineralization. Discussion of the ore genesis shows that the greenish gray sandstone plays a crucial role during processes leading to uranium mineralization. Consequently, an oxidation-reduction model for

  15. Submarine fan facies of Upper Cretaceous Strata, Southern San Rafael Mountains, Santa Barbara County, California

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Toyne, C.D.

    1986-04-01

    A 2900-m thick Campanian-Maestrichtian(.) turbidite sequence in Upper Mono Creek Canyon is interpreted to be a progradational submarine fan complex comprised of outer fan, middle fan, inner fan, and slope facies. The basal 600 m of the section consists of thinly bedded, laterally continuous fine sandstones, siltstones, and mudstones (mainly Mutti and Ricci Lucci facies D), interpreted to be outer fan interlobe and lobe-fringe deposits. These are punctuated by infrequent medium to very thickly bedded, flat-based, fine to coarse sandstones (facies C and B), which commonly coarsen and thicken upward, and are interpreted to be depositional lobes. Overlying these depositsmore » are approximately 1400 m of middle fan deposits composed of frequent lenticular, commonly channelized and amalgamated, thickly bedded, fine to very coarse sandstones (facies C and B) organized in fining- and thinning-upward sequences, interpreted to be braided-channel deposits. These alternate with less common nonchannelized coarsening- and thickening-upward sequences suggestive of lobe-apical cycles. These multistory sand deposits are nested within thick intervals of fine sandstones, siltstones, and mudstones (facies C and D), interpreted to be levee, crevasse-splay, and interchannel deposits. Interfingered with and overlying these deposits are approximately 500 m of fining- and thinning-upward or noncyclic, erosionally based, commonly amalgamated, very thickly bedded, medium to very coarse sandstones, pebbly sandstones, and conglomerates (facies A and B), interpreted to be inner fan deposits. Intercalated within this facies, infrequent, laterally discontinuous, thin to thickly bedded, fine to coarse sandstones, siltstones, and mudstones exist, interpreted to be interchannel, levee, and possibly channel-fill deposits.« less

  16. A new bee species that excavates sandstone nests

    USDA-ARS?s Scientific Manuscript database

    Many wonder why animals act in seemingly injurious ways. Understanding the behavior of pollinators such as bees is especially important because of the necessary ecosystem service they provide. The new species Anthophora pueblo, discovered excavating sandstone nests, provides a model system for addre...

  17. Dinosaur Footprints and Other Ichnofauna from the Cretaceous Kem Kem Beds of Morocco

    PubMed Central

    Ibrahim, Nizar; Varricchio, David J.; Sereno, Paul C.; Wilson, Jeff A.; Dutheil, Didier B.; Martill, David M.; Baidder, Lahssen; Zouhri, Samir

    2014-01-01

    We describe an extensive ichnofossil assemblage from the likely Cenomanian-age ‘lower’ and ‘upper’ units of the ‘Kem Kem beds’ in southeastern Morocco. In the lower unit, trace fossils include narrow vertical burrows in cross-bedded sandstones and borings in dinosaur bone, with the latter identified as the insect ichnotaxon Cubiculum ornatus. In the upper unit, several horizons preserve abundant footprints from theropod dinosaurs. Sauropod and ornithischian footprints are much rarer, similar to the record for fossil bone and teeth in the Kem Kem assemblage. The upper unit also preserves a variety of invertebrate traces including Conichnus (the resting trace of a sea-anemone), Scolicia (a gastropod trace), Beaconites (a probable annelid burrow), and subvertical burrows likely created by crabs for residence and detrital feeding on a tidal flat. The ichnofossil assemblage from the Upper Cretaceous Kem Kem beds contributes evidence for a transition from predominantly terrestrial to marine deposition. Body fossil and ichnofossil records together provide a detailed view of faunal diversity and local conditions within a fluvial and deltaic depositional setting on the northwestern coast of Africa toward the end of the Cretaceous. PMID:24603467

  18. Effects of pore pressure and mud filtration on drilling rates in a permeable sandstone

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Black, A.D.; DiBona, B.; Sandstrom, J.

    1983-10-01

    During laboratory drilling tests in a permeable sandstone, the effects of pore pressure and mud filtration on penetration rates were measured. Four water-base muds were used to drill four saturated sandstone samples. The drilling tests were conducted at constant borehole pressure with different back pressures maintained on the filtrate flowing from the bottom of the sandstone samples. Bit weight was also varied. Filtration rates were measured while drilling and with the bit off bottom and mud circulating. Penetration rates were found to be related to the difference between the filtration rates measured while drilling and circulating. There was no observedmore » correlation between standard API filtration measurements and penetration rate.« less

  19. Effects of pore pressure and mud filtration on drilling rates in a permeable sandstone

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Black, A.D.; Dearing, H.L.; DiBona, B.G.

    1985-09-01

    During laboratory drilling tests in a permeable sandstone, the effects of pore pressure and mud filtration on penetration rates were measured. Four water-based muds were used to drill four saturated sandstone samples. The drilling tests were conducted at constant borehole pressure while different backpressures were maintained on the filtrate flowing from the bottom of the sandstone samples. Bit weight was varied also. Filtration rates were measured while circulating mud during drilling and with the bit off bottom. Penetration rates were found to be related qualitatively to the difference between the filtration rates measured while drilling and circulating. There was nomore » observed correlation between standard API filtration measurements and penetration rate.« less

  20. Ability of bed bug-detecting canines to locate live bed bugs and viable bed bug eggs.

    PubMed

    Pfiester, Margie; Koehler, Philip G; Pereira, Roberto M

    2008-08-01

    The bed bug, Cimex lectularius L., like other bed bug species, is difficult to visually locate because it is cryptic. Detector dogs are useful for locating bed bugs because they use olfaction rather than vision. Dogs were trained to detect the bed bug (as few as one adult male or female) and viable bed bug eggs (five, collected 5-6 d after feeding) by using a modified food and verbal reward system. Their efficacy was tested with bed bugs and viable bed bug eggs placed in vented polyvinyl chloride containers. Dogs were able to discriminate bed bugs from Camponotus floridanus Buckley, Blattella germanica (L.), and Reticulitermes flavipes (Kollar), with a 97.5% positive indication rate (correct indication of bed bugs when present) and 0% false positives (incorrect indication of bed bugs when not present). Dogs also were able to discriminate live bed bugs and viable bed bug eggs from dead bed bugs, cast skins, and feces, with a 95% positive indication rate and a 3% false positive rate on bed bug feces. In a controlled experiment in hotel rooms, dogs were 98% accurate in locating live bed bugs. A pseudoscent prepared from pentane extraction of bed bugs was recognized by trained dogs as bed bug scent (100% indication). The pseudoscent could be used to facilitate detector dog training and quality assurance programs. If trained properly, dogs can be used effectively to locate live bed bugs and viable bed bug eggs.

  1. Debris-bed friction of hard-bedded glaciers

    USGS Publications Warehouse

    Cohen, D.; Iverson, N.R.; Hooyer, T.S.; Fischer, U.H.; Jackson, M.; Moore, P.L.

    2005-01-01

    [1] Field measurements of debris-bed friction on a smooth rock tablet at the bed of Engabreen, a hard-bedded, temperate glacier in northern Norway, indicated that basal ice containing 10% debris by volume exerted local shear traction of up to 500 kPa. The corresponding bulk friction coefficient between the dirty basal ice and the tablet was between 0.05 and 0.08. A model of friction in which nonrotating spherical rock particles are held in frictional contact with the bed by bed-normal ice flow can account for these measurements if the power law exponent for ice flowing past large clasts is 1. A small exponent (n < 2) is likely because stresses in ice are small and flow is transient. Numerical calculations of the bed-normal drag force on a sphere in contact with a flat bed using n = 1 show that this force can reach values several hundred times that on a sphere isolated from the bed, thus drastically increasing frictional resistance. Various estimates of basal friction are obtained from this model. For example, the shear traction at the bed of a glacier sliding at 20 m a-1 with a geothermally induced melt rate of 0.006 m a-1 and an effective pressure of 300 kPa can exceed 100 kPa. Debris-bed friction can therefore be a major component of sliding resistance, contradicting the common assumption that debris-bed friction is negligible. Copyright 2005 by the American Geophysical Union.

  2. Saga of coal bed methane, Ignacio Blanco gas field, Colorado

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Boyce, B.C.; Harr, C.L.; Burch, L.C.

    1989-09-01

    Prior to the 1977 discovery of the Cedar Hill Basal Fruitland pool (the first officially designated coal-bed methane field in the western US) 28.5 bcf of gas had been produced from Fruitland Formation coal seams in the Ignacio Blanco Fruitland-Pictured Cliffs field, Northern San Juan basin, Colorado. The discovery well for the field, Southern Ute D-1, was drilled and completed in 1951 on the Ignacio anticline, La Plata County, Colorado. Initial completion was attempted in the Pictured Cliffs Sandstone. The well was plugged back after making water from the Pictured Cliffs and was completed in the lower coal-bearing section ofmore » the Fruitland Formation. The well produced 487,333 mcf of gas in nine years and was abandoned in 1959 due to water encroachment. Additionally, 52 similarly completed Ignacio anticline Fruitland wells were abandoned by the early 1970s due to the nemesis of If it's starting to kick water, you're through. Under today's coal-bed methane technology and economics, Amoco has twinned 12 of the abandoned wells, drilled five additional wells, and is successfully dewatering and producing adsorbed methane from previously depleted coal sections of the Ignacio structure. Field-wide drilling activity in 1988 exceeded all previous annual levels, with coal-seam degasification projects leading the resurgence. Drilling and completion forecasts for 1989 surpass 1988 levels by 50%.« less

  3. Particle size variations between bed load and bed material in natural gravel bed channels

    Treesearch

    Thomas E. Lisle

    1995-01-01

    Abstract - Particle sizes of bed load and bed material that represent materials transported and stored over a period of years are used to investigate selective transport in 13 previously sampled, natural gravel bed channels. The ratio (D*) of median particle size of bed material to the transport- and frequency-weighted mean of median bed load size decreases to unity...

  4. Petrophysics of Lower Silurian sandstones and integration with the tectonic-stratigraphic framework, Appalachian basin, United States

    USGS Publications Warehouse

    Castle, J.W.; Byrnes, A.P.

    2005-01-01

    Petrophysical properties were determined for six facies in Lower Silurian sandstones of the Appalachian basin: fluvial, estuarine, upper shoreface, lower shoreface, tidal channel, and tidal flat. Fluvial sandstones have the highest permeability for a given porosity and exhibit a wide range of porosity (2-18%) and permeability (0.002-450 md). With a transition-zone thickness of only 1-6 m (3-20 ft), fluvial sandstones with permeability greater than 5 md have irreducible water saturation (Siw) less than 20%, typical of many gas reservoirs. Upper shoreface sandstones exhibit good reservoir properties with high porosity (10-21%), high permeability (3-250 md), and low S iw (<20%). Lower shoreface sandstones, which are finer grained, have lower porosity (4-12%), lower permeability (0.0007-4 md), thicker transition zones (6-180 m [20-600 ft]), and higher S iw. In the tidal-channel, tidal-flat, and estuarine facies, low porosity (average < 6%), low permeability (average < 0.02 md), and small pore throats result in large transition zones (30-200 m; 100-650 ft) and high water saturations. The most favorable reservoir petrophysical properties and the best estimated production from the Lower Silurian sandstones are associated with fluvial and upper shoreface facies of incised-valley fills, which we interpret to have formed predominantly in areas of structural recesses that evolved from promontories along a collisional margin during the Taconic orogeny. Although the total thickness of the sandstone may not be as great in these areas, reservoir quality is better than in adjacent structural salients, which is attributed to higher energy depositional processes and shallower maximum burial depth in the recesses than in the salients. Copyright ??2005. The American Association of Petroleum Geologists. All rights reserved.

  5. Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

    NASA Astrophysics Data System (ADS)

    Marquis, G. A.; Roy, A. G.

    2012-02-01

    This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

  6. The Cyborg Astrobiologist: scouting red beds for uncommon features with geological significance

    NASA Astrophysics Data System (ADS)

    McGuire, Patrick Charles; Díaz-Martínez, Enrique; Ormö, Jens; Gómez-Elvira, Javier; Rodríguez-Manfredi, José Antonio; Sebastián-Martínez, Eduardo; Ritter, Helge; Haschke, Robert; Oesker, Markus; Ontrup, Jörg

    2005-04-01

    The `Cyborg Astrobiologist' has undergone a second geological field trial, at a site in northern Guadalajara, Spain, near Riba de Santiuste. The site at Riba de Santiuste is dominated by layered deposits of red sandstones. The Cyborg Astrobiologist is a wearable computer and video camera system that has demonstrated a capability to find uncommon interest points in geological imagery in real time in the field. In this second field trial, the computer vision system of the Cyborg Astrobiologist was tested at seven different tripod positions, on three different geological structures. The first geological structure was an outcrop of nearly homogeneous sandstone, which exhibits oxidized-iron impurities in red areas and an absence of these iron impurities in white areas. The white areas in these `red beds' have turned white because the iron has been removed. The iron removal from the sandstone can proceed once the iron has been chemically reduced, perhaps by a biological agent. In one instance the computer vision system found several (iron-free) white spots to be uncommon and therefore interesting, as well as several small and dark nodules. The second geological structure was another outcrop some 600 m to the east, with white, textured mineral deposits on the surface of the sandstone, at the bottom of the outcrop. The computer vision system found these white, textured mineral deposits to be interesting. We acquired samples of the mineral deposits for geochemical analysis in the laboratory. This laboratory analysis of the crust identifies a double layer, consisting of an internal millimetre-size layering of calcite and an external centimetre-size efflorescence of gypsum. The third geological structure was a 50 cm thick palaeosol layer, with fossilized root structures of some plants. The computer vision system also found certain areas of these root structures to be interesting. A quasi-blind comparison of the Cyborg Astrobiologist's interest points for these images with the

  7. Petrography and geochemistry of the Middle Miocene Gebel El Rusas sandstones, Eastern Desert, Egypt: Implications for provenance and tectonic setting

    NASA Astrophysics Data System (ADS)

    Zaid, Samir M.

    2017-10-01

    Petrography and bulk rock geochemistry of the Middle Miocene sandstones of the lower and upper members of Gebel El Rusas Formation along the Egyptian Red Sea Coastal plain, have been investigated to determine the provenance, tectonic setting, and weathering condition of this formation. The Lower Member is formed mainly of sandstones and conglomerates with clay interbeds. The Upper Member is more calcareous and formed mainly of sandstones and limestones with marls and clays intercalations. Petrographically, the Lower Member sandstones are mostly immature and classified as arkoses with an average framework composition of Q_{66}F_{29}R5, and the Upper Member sandstones are partly submature (more quartzose, less feldspathic) and classified as subarkoses with an average framework composition of Q_{80}F_{17}R3. The Gebel El Rusas sandstones are enriched in Sr, Ba, Zr and Rb and depleted in Co and U, as compared to UCC. The chemical index of alteration (CIA) values suggest moderate weathering conditions. The geochemistry results revealed that the Gebel El Rusas sandstones were derived from felsic-granitic source rocks and deposited in a passive margin of a synrift basin. The inferred tectonic setting for Middle Miocene Gebel El Rusas sandstones in the study area is consistent with the regional geology of the Eastern Desert of Egypt during Middle Miocene.

  8. Fractures and stresses in Bone Spring sandstones. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Warpinski, N.R.; Sattler, A.R.; Lorenz, J.C.

    This project was a collaboration between Sandia National Laboratories and the Harvey E. Yates Company (Heyco), Roswell, NM, conducted under the auspices of Department of Energy`s Oil Recovery Technology Partnership. The project applied Sandia perspectives on the effects of natural fractures, stress, and sedimentology for the stimulation and production of low permeability gas reservoirs to low permeability oil reservoirs, such as those typified by the Bone Spring sandstones of the Delaware Basin, southeast New Mexico. This report details the results and analyses obtained in 1990 from core, logs, stress, and other data taken from three additional development wells. An overallmore » summary gives results from all five wells studied in this project in 1989--1990. Most of the results presented are believed to be new information for the Bone Spring sandstones.« less

  9. Pore-throat sizes in sandstones, siltstones, and shales: Reply

    USGS Publications Warehouse

    Nelson, Philip H.

    2011-01-01

    In his discussion of my article (Nelson, 2009), W. K. Camp takes issue with the concept that buoyancy is not the dominant force in forming and maintaining the distribution of gas in tight-gas accumulations (Camp, 2011). I will restrict my response to the issues he raised regarding buoyant versus nonbuoyant drive and to a few comments regarding water saturation and production. I claim that the pressure generated in petroleum source rocks (Pg), instead of the buoyancy pressure (Pb), provides the energy to charge most tight sandstones with gas. The arguments are fourfold: (1) buoyant columns of sufficient height seldom exist in low-permeability sand-shale sequences, (2) tight-gas systems display a pressure profile that declines instead of increases upward, (3) gas is pervasive in overpressured systems, and (4) source rocks can generate pore pressures sufficiently high to charge tight sandstones.

  10. Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Châteauguay River Basin, a U.S.-Canada transborder aquifer

    NASA Astrophysics Data System (ADS)

    Morin, Roger; Godin, RéJean; Nastev, Miroslav; Rouleau, Alain

    2007-04-01

    The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

  11. Hydrogeologic controls imposed by mechanical stratigraphy in layered rocks of the Chateauguay River Basin, a U.S.-Canada transborder aquifer

    USGS Publications Warehouse

    Morin, Roger H.; Godin, Rejean; Nastev, Miroslav; Rouleau, Alain

    2007-01-01

    [1] The Châteauguay River Basin delineates a transborder watershed with roughly half of its surface area located in northern New York State and half in southern Québec Province, Canada. As part of a multidisciplinary study designed to characterize the hydrogeologic properties of this basin, geophysical logs were obtained in 12 wells strategically located to penetrate the four major sedimentary rock formations that constitute the regional aquifers. The layered rocks were classified according to their elastic properties into three primary units: soft sandstone, hard sandstone, and dolostone. Downhole measurements were analyzed to identify fracture patterns associated with each unit and to evaluate their role in controlling groundwater flow. Fracture networks are composed of orthogonal sets of laterally extensive, subhorizontal bedding plane partings and bed-delimited, subvertical joints with spacings that are consistent with rock mechanics principles and stress models. The vertical distribution of transmissive zones is confined to a few select bedding plane fractures, with soft sandstone having the fewest (one per 70-m depth) and hard sandstone the most (five per 70-m depth). Bed-normal permeability is examined using a probabilistic model that considers the lengths of flow paths winding along joints and bedding plane fractures. Soft sandstone has the smallest bed-normal permeability primarily because of its wide, geomechanically undersaturated joint spacing. Results indicate that the three formations have similar values of bulk transmissivity, within roughly an order of magnitude, but that each rock unit has its own unique system of groundwater flow paths that constitute that transmissivity.

  12. The Collyhurst Sandstone as a secondary storage unit for CCS in the East Irish Sea Basin (UK)

    NASA Astrophysics Data System (ADS)

    Gamboa, D.; Williams, J. D. O.; Kirk, K.; Gent, C. M. A.; Bentham, M.; Schofield, D. I.

    2016-12-01

    Carbon Capture and Storage (CCS) is key technology for low-carbon energy and industry. The UK hosts a large CO2 storage potential offshore with an estimated capacity of 78 Gt. The East Irish Sea Basin (EISB) is the key area for CCS in the western UK, with a CO2 storage potential of 1.7 Gt in hydrocarbon fields and in saline aquifers within the Triassic Sherwood Sandstone Formation. However, this theoretical storage capacity does not consider the secondary storage potential in the lower Permian Collyhurst Sandstone Formation. 3D seismic data were used to characterise the Collyhurst Sandstone Formation in the EISB. On the southern basin domain, numerous fault-bound blocks limit the lateral continuity of the sandstone strata, while on the northern domain the sandstones are intersected by less faults. The caprock for the Collyhurst sandstones is variable. The Manchester Marls predominate in the south, transitioning to the St. Bees evaporites towards the north. The evaporites in the EISB cause overburden faults to terminate or detach along Upper Permian strata, limiting the deformation of the underlying reservoir units. Five main storage closures have been identified in the Permian strata. In the southern and central area these are predominantly fault bounded, occurring at depths over 1000m. Despite the higher Collyhurst sandstone thickness in the southern IESB, the dolomitic nature of the caprock constitutes a storage risk in this area. Closures in the northern area are deeper (around 2000-2500m) and wider, reaching areas of 34Km2, and are overlain by evaporitic caprocks. The larger Collyhurst closures to the north underlie large Triassic fields with high storage potential. The spatial overlap favours storage plans including secondary storage units in the EISB. The results of this work also expand the understanding of prospective areas for CO2 sequestration in the East Irish Sea Basin in locations where the primary Sherwood Sandstone Formation is either too shallow

  13. The fauna of the so-called Dakota formation of northern central Colorado and its equivalent in southeastern Wyoming

    USGS Publications Warehouse

    Reeside, John B.

    1923-01-01

    This paper describes a small fauna from beds in northern central Colorado that have long been designated the Dakota formation, often with doubt that all the beds so named were really equivalent to the typical Dakota sandstone of eastern Nebraska. The upper part of the equivalent beds in southeastern Wyoming was referred by some writers to the Benton Shale and the lower part of the Cloverly formation. This so-called Dakota formation of northern central Colorado and its equivalent in southeastern Wyoming consist of cherty conglomerate, brown quartzose sandstone, and dark shale. The conglomerate is usually at the base of the series and at many localities is overlain by a single shale unit and that in turn by a sandstone. At other localities, however, there are several alternations of sandstone and shale above the basal conglomeratic layer. The fossil described in this paper, except one specimen, were obtained from the shales of the middle part of the formation. The single specimen, an ammonite, came from the uppermost sandstone.

  14. Sample-Collection Drill Hole on Martian Sandstone Target Windjana

    NASA Image and Video Library

    2014-05-06

    This image from the Navigation Camera Navcam on NASA Curiosity Mars rover shows two holes at top center drilled into a sandstone target called Windjana. The farther hole, with larger pile of tailings around it, is a full-depth sampling hole.

  15. Proposed moduli of dry rock and their application to predicting elastic velocities of sandstones

    USGS Publications Warehouse

    Lee, Myung W.

    2005-01-01

    Velocities of water-saturated isotropic sandstones under low frequency can be modeled using the Biot-Gassmann theory if the moduli of dry rocks are known. On the basis of effective medium theory by Kuster and Toksoz, bulk and shear moduli of dry sandstone are proposed. These moduli are related to each other through a consolidation parameter and provide a new way to calculate elastic velocities. Because this parameter depends on differential pressure and the degree of consolidation, the proposed moduli can be used to calculate elastic velocities of sedimentary rocks under different in-place conditions by varying the consolidation parameter. This theory predicts that the ratio of P-wave to S-wave velocity (Vp/Vs) of a dry rock decreases as differential pressure increases and porosity decreases. This pattern of behavior is similar to that of water-saturated sedimentary rocks. If microcracks are present in sandstones, the velocity ratio usually increases as differential pressure increases. This implies that this theory is optimal for sandstones having intergranular porosities. Even though the accurate behavior of the consolidation parameter with respect to differential pressure or the degree of consolidation is not known, this theory presents a new way to predict S-wave velocity from P-wave velocity and porosity and to calculate elastic velocities of gas-hydrate-bearing sediments. For given properties of sandstones such as bulk and shear moduli of matrix, only the consolidation parameter affects velocities, and this parameter can be estimated directly from the measurements; thus, the prediction of S-wave velocity is accurate, reflecting in-place conditions.

  16. Characterization of a fluvial aquifer at a range of depths and scales: the Triassic St Bees Sandstone Formation, Cumbria, UK

    NASA Astrophysics Data System (ADS)

    Medici, Giacomo; West, L. J.; Mountney, N. P.

    2018-03-01

    Fluvial sedimentary successions represent porous media that host groundwater and geothermal resources. Additionally, they overlie crystalline rocks hosting nuclear waste repositories in rift settings. The permeability characteristics of an arenaceous fluvial succession, the Triassic St Bees Sandstone Formation in England (UK), are described, from core-plug to well-test scale up to 1 km depth. Within such lithified successions, dissolution associated with the circulation of meteoric water results in increased permeability ( K 10-1-100 m/day) to depths of at least 150 m below ground level (BGL) in aquifer systems that are subject to rapid groundwater circulation. Thus, contaminant transport is likely to occur at relatively high rates. In a deeper investigation (> 150 m depth), where the aquifer has not been subjected to rapid groundwater circulation, well-test-scale hydraulic conductivity is lower, decreasing from K 10-2 m/day at 150-400 m BGL to 10-3 m/day down-dip at 1 km BGL, where the pore fluid is hypersaline. Here, pore-scale permeability becomes progressively dominant with increasing lithostatic load. Notably, this work investigates a sandstone aquifer of fluvial origin at investigation depths consistent with highly enthalpy geothermal reservoirs ( 0.7-1.1 km). At such depths, intergranular flow dominates in unfaulted areas with only minor contribution by bedding plane fractures. However, extensional faults represent preferential flow pathways, due to presence of high connective open fractures. Therefore, such faults may (1) drive nuclear waste contaminants towards the highly permeable shallow (< 150 m BGL) zone of the aquifer, and (2) influence fluid recovery in geothermal fields.

  17. Sandstone copper assessment of the Teniz Basin, Kazakhstan: Chapter R in Global mineral resource assessment

    USGS Publications Warehouse

    Cossette, Pamela M.; Bookstrom, Arthur A.; Hayes, Timothy S.; Robinson, Gilpin R.; Wallis, John C.; Zientek, Michael L.

    2014-01-01

    A quantitative mineral resource assessment has been completed that (1) delineates one 49,714 km2 tract permissive for undiscovered, sandstone subtype, sediment-hosted stratabound copper deposits, and (2) provides probabilistic estimates of numbers of undiscovered deposits and probable amounts of copper resource contained in those deposits. The permissive tract delineated in this assessment encompasses no previously known sandstone subtype, sediment-hosted stratabound copper deposits. However, this assessment estimates (with 30 percent probability) that a mean of nine undiscovered sandstone subtype copper deposits may be present in the Teniz Basin and could contain a mean total of 8.9 million metric tons of copper and 7,500 metric tons of silver.

  18. Use of seasonal trend decomposition to understand groundwater behaviour in the Permo-Triassic Sandstone aquifer, Eden Valley, UK

    NASA Astrophysics Data System (ADS)

    Lafare, Antoine E. A.; Peach, Denis W.; Hughes, Andrew G.

    2016-02-01

    The daily groundwater level (GWL) response in the Permo-Triassic Sandstone aquifers in the Eden Valley, England (UK), has been studied using the seasonal trend decomposition by LOESS (STL) technique. The hydrographs from 18 boreholes in the Permo-Triassic Sandstone were decomposed into three components: seasonality, general trend and remainder. The decomposition was analysed first visually, then using tools involving a variance ratio, time-series hierarchical clustering and correlation analysis. Differences and similarities in decomposition pattern were explained using the physical and hydrogeological information associated with each borehole. The Penrith Sandstone exhibits vertical and horizontal heterogeneity, whereas the more homogeneous St Bees Sandstone groundwater hydrographs characterize a well-identified seasonality; however, exceptions can be identified. A stronger trend component is obtained in the silicified parts of the northern Penrith Sandstone, while the southern Penrith, containing Brockram (breccias) Formation, shows a greater relative variability of the seasonal component. Other boreholes drilled as shallow/deep pairs show differences in responses, revealing the potential vertical heterogeneities within the Penrith Sandstone. The differences in bedrock characteristics between and within the Penrith and St Bees Sandstone formations appear to influence the GWL response. The de-seasonalized and de-trended GWL time series were then used to characterize the response, for example in terms of memory effect (autocorrelation analysis). By applying the STL method, it is possible to analyse GWL hydrographs leading to better conceptual understanding of the groundwater flow. Thus, variation in groundwater response can be used to gain insight into the aquifer physical properties and understand differences in groundwater behaviour.

  19. Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions

    PubMed Central

    2011-01-01

    Background Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. Results We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Conclusions Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface. PMID:22078161

  20. Nivelstein sandstone, weakly lithified pure silica sands from the Dutch-German border area, intermittently used in architecture for two millennia

    NASA Astrophysics Data System (ADS)

    Nijland, Timo G.; Wim Dubelaar, C.

    2017-04-01

    The current paper provides a concise overview of the geological setting of the Nivelstein sandstone in broad sense, its petrographic and physical characteristics, and its use as natural stone. Miocene pure silica sands occur around Heerlen in the southeastern part of the Dutch province of Limburg and Herzogenrath in adjacent Germany, as well as in the Belgian province of Limburg near Opgrimbie. In Dutch Limburg and in Germany are three large active exploitations, quarrying the sands for industrial purposes. On top of the unconsolidated sands in the Herzogenrath quarry, lithified banks of sandstone occur, known as Nivelstein (or more rarely Herzogenrath) sandstone. This sandstone has been used as dimension stone and ornamental stone since Roman times. In the 11th century the quarry was reopened and after a long period of disuse sandstone blocks were again quarried in the second half of the 19th century. The lithification of the Nivelstein sandstone usually is very weak, with grain to grain contacts and some newly formed quartz rims only. The clay content is extremely low and is restricted to tiny booklets of kaolinite. Despite the weak cementation the Nivelstein sandstone has proved to be very time-resistant building stone that forms a major element in the stone cultural heritage of the Dutch- German border area.

  1. Uranium resources in the Silver Reef (Harrisburg) district, Washington County, Utah

    USGS Publications Warehouse

    Stugard, Frederick

    1951-01-01

    The Silver Reef district is near Leeds, about 16 miles north of St. George, Utah. The major structural feature of the district is the Virgin anticline, a fold extending southwestward toward St. George. The anticline has been breached by erosion, and sandstone hogbacks or 'reefs' are carved from the Shinarump conglomerate mud sandstone members of the Chinle formation, both of Triassic age. Thirteen occurrences of uranium-vanadium minerals, all within the Tecumseh sandstone, which is the upper part of the Silver Reef sandstone member of the Chinle formation, have been examined over an area about 1.75 miles wide and 3 miles long. Two shipments of uranium-vanadium ore have been produced from the Chloride Chief and Silver Point claims. Samples from the deposits contain as much as 0.94 percent U3O8. The ore contains several times as much vanadium oxide as uranium, some copper, and traces of silver. It occurs in thinly bedded cross-bedded shales and sandstones within the fluviatile Tecumseh sandstone member of the Chinle formation. The ore beds are lenticular and are localized 2 near the base, center, and top of this sandstone member. The uranium-vanadium ore contains several yellow and green minerals not yet identified; the occurrences are similar to, but not associated with, the cerargyrite ore that made the district famous from 1879 to 1909.

  2. CHARACTERIZATION OF SANDSTONE RESERVOIRS FOR ENHANCED OIL RECOVERY: THE PERMIAN UPPER MINNELUSA FORMATION, POWDER RIVER BASIN, WYOMING.

    USGS Publications Warehouse

    Schenk, C.J.; Schmoker, J.W.; Scheffler, J.M.

    1986-01-01

    Upper Minnelusa sandstones form a complex group of reservoirs because of variations in regional setting, sedimentology, and diagenetic alteration. Structural lineaments separate the reservoirs into northern and southern zones. Production in the north is from a single pay sand, and in the south from multi-pay sands due to differential erosion on top of the Upper Minnelusa. The intercalation of eolian dune, interdune, and sabkha sandstones with marine sandstones, carbonates, and anhydrites results in significant reservoir heterogeneity. Diagenetic alterations further enhance heterogeneity, because the degree of cementation and dissolution is partly facies-related.

  3. Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

    NASA Astrophysics Data System (ADS)

    Burki, Milad; Darwish, Mohamed

    2017-06-01

    The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

  4. Giant weathering pits in the Entrada Sandstone, southeastern Utah: Preliminary findings

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Netoff, D.I.; Shroba, R.R.

    Giant weathering pits formed in outcrops of the lower Entrada Sandstone slickrock of Jurassic age are present in two areas in the Glen Canyon region of arid southeastern Utah. The pits are far larger than any previously described in the geologic literature. The pits near Cookie Jar Butte are commonly cylindrical, typically have low width-to-depth ratios (1.5--3.6), and have a depth of closure of as much as 18 m. There are no obvious lithologic or structural controls that determine their shape or location. Many of the pits at Rock Creek Bay are elongate; several of them have long axes inmore » excess of 53 m, and the longest one is 74 m. Many of the pit walls are breached at the top, and the depth of closure is generally less than 6 m. The shapes of these pits are influenced by point orientation and pit coalescence. Thin-section analyses of near-surface sandstone cores taken near Cookie Jar Butte from pit walls, floors, and rims reveal no significant diagenetic alteration of the fine-grained to very fine frained quartzose sandstone (quartz arenite). Quartz grains appear fresh, and feldspar grains are only slightly weathered. The cement between the grains is mostly CaCO[sub 3]. In several of the pits in both areas sandy sediment veneers the bedrock floor. This sediment is similar in character to the adjacent sandstone and is probably locally derived. Possible origins of the giant pits include various physical, chemical, and biological weathering processes that initiate pit development, followed by excavation by plunge-pool action, wind deflation, dissolution, and piping. Preliminary field and laboratory data do not clearly identify and single process of group of processes that account for pit development.« less

  5. Simulation of forced convection in non-Newtonian fluid through sandstones

    NASA Astrophysics Data System (ADS)

    Gokhale, M. Y.; Fernandes, Ignatius

    2017-11-01

    Numerical simulation is carried out to study forced convection in non-Newtonian fluids flowing through sandstones. Simulation is carried out using lattice Boltzmann method (LBM) for both shear-thinning and shear-thickening, by varying the power law index from 0.5 to 1.5 in Carreau-Yasuda model. Parameters involved in LBM and Carreau model are identified to achieve numerical convergence. Permeability and porosity are varied in the range of 10-10-10-6 and 0.1-0.7, respectively, to match actual geometrical properties of sandstone. Numerical technology is validated by establishing Darcy's law by plotting the graph between velocity and pressure gradient. Consequently, investigation is carried out to study the influence of material properties of porous media on flow properties such as velocity profiles, temperature profiles, and Nusselt number.

  6. Is there a basin-centered gas accumulation in Cotton Valley Group Sandstones, Gulf Coast Basin, U.S.A.?

    USGS Publications Warehouse

    Bartberger, Charles E.; Dyman, Thaddeus S.; Condon, Steven M.

    2002-01-01

    The U.S. Geological Survey (USGS), in cooperation with the U.S. Department of Energy, is reevaluating the resource potential of selected domestic basin-centered gas accumulations. Basin-centered gas accumulations are characterized by presence of gas in extensive low-permeability (tight) reservoirs in which conventional seals and trapping mechanisms are absent, abnormally high or low reservoir pressures exist, and gas-water contacts are absent. In 1995, the USGS assessed one basin-centered gas play and two conventional plays within the trend of Jurassic and Cretaceous Cotton Valley Group fl uvial-deltaic and barrierisland/ strandplain sandstones across the onshore northern Gulf of Mexico Basin. Detailed evaluation of geologic and production data provides new insights into these Cotton Valley plays. Two Cotton Valley sandstone trends are identifi ed based on reservoir properties and gas-production characteristics. Transgressive blanket sandstones across northern Louisiana have relatively high porosity and permeability and do not require fracture stimulation to produce gas at commercial rates. South of this trend, and extending westward into eastern Texas, massive sandstones of the Cotton Valley trend exhibit low porosity and permeability and require fracture stimulation. The high permeability of Cotton Valley blanket sandstones is not conducive to the presence of basin-centered gas, but lowpermeability massive sandstones provide the type of reservoir in which basin-centered gas accumulations commonly occur. Data on source rocks, including burial and thermal history, are consistent with the interpretation of potential basincentered gas within Cotton Valley sandstones. However, pressure gradients throughout most of the blanket- and massivesandstone trends are normal or nearly normal, which is not characteristic of basin-centered gas accumulations. The presence of gas-water contacts in at least seven fi elds across the blanket-sandstone trend together with relatively

  7. Petrology and stratigraphy of Paleogene nonmarine sandstones, Cascade Range, Washington

    USGS Publications Warehouse

    Frizzell, Virgil A.

    1979-01-01

    The Cascade Range of Washington north of 47? latitude is composed of probable Paleozoic and Mesozoic metamorphic rocks and Mesozoic and Tertiary plutonic rocks. Several Paleogene nonmarine arkosic sandstone units fringe and in part occur within the complex crystalline core. The early to middle Eocene Chuckanut Formation is present on the west side of the crystalline core in the western foothills of the Cascades. The early to middle Eocene Swauk Formation partially encircles the Mt. Stuart massif of the central Cascades. In the western foothills of the Cascades, between the main body of Chuckanut Formation near Bellingham and the main outcrop area of the Swauk Formation south of Mt. Stuart, many smaller bodies of arkosic sandstone have variously been referred to either the Swauk or Chuckanut Formations. The early Eocene Manastash Formation occurs locally in an area south of the Yakima River. The middle to late Eocene Chumstick Formation is mostly confined to the Chiwaukum graben within the crystalline core and is separated from the Swauk Formation on the southwest by the Leavenworth Fault. The Oligocene Wenatchee Formation unconformably over lies the Chumstick Formation near Wenatchee. The middle to late Eocene Roslyn Formation crops out north of the Yakima River and is underlain by the Teanaway Basalt which separates the Roslyn from the older Swauk Formation. The middle Eocene to early Oligocene Naches Formation forms a north-trending body that crosses the Yakima River and is in fault contact with both the Swauk and Manastash Formations. The middle to late Eocene Puget Group underlies the Quaternary deposits of the Puget Lowland southeast of Seattle on the western flank of the Cascades. The various formations are all composed predominantly of fine- to medium-grained sandstones with lesser amounts of interbedded shale, conglomerate and coal. Compositionally, the units are predominantly either feldspathic or litho-feldspathic subquartzose sandstones. Volcanic rocks

  8. Lattice Boltzmann Simulation of Seismic Mobilization of Residual Oil in Sandstone

    NASA Astrophysics Data System (ADS)

    Guo, R.; Jiang, F.; Deng, W.

    2017-12-01

    Seismic stimulation is a promising technology for enhanced oil recovery. However, current mechanism studies are mainly in the single constricted tubes or idealized porous media, and no study has been conducted in real reservoir porous media. We have developed a numerical simulation which uses the lattice Boltzmann method to directly calculate the characteristics of residual oil clusters to quantify seismic mobilization of residual oil in real Berea sandstone in a scale of 400μm x 400μm x 400μm. The residual oil clusters will be firstly obtained by applying the water flooding scheme to the oil-saturated sandstone. Then, we will apply the seismic stimulation to the sandstone by converting the seismic effect to oscillatory inertial force and add to the pore fluids. This oscillatory inertial force causes the mobilization of residual oil by overcoming the capillary force. The response of water and oil to the seismic stimulation will be observed in our simulations. Two seismic oil mobilization mechanisms will be investigated: (1) the passive response of residual oil clusters to the seismic stimulation, and (2) the resonance of oil clusters subject to low frequency seismic stimulation. We will then discuss which mechanism should be the dominant mechanism for the seismic stimulation oil recovery for practical applications.

  9. Diagenesis and reservoir quality of the Lower Cretaceous Quantou Formation tight sandstones in the southern Songliao Basin, China

    NASA Astrophysics Data System (ADS)

    Xi, Kelai; Cao, Yingchang; Jahren, Jens; Zhu, Rukai; Bjørlykke, Knut; Haile, Beyene Girma; Zheng, Lijing; Hellevang, Helge

    2015-12-01

    The Lower Cretaceous Quantou Formation in the southern Songliao Basin is the typical tight oil sandstone in China. For effective exploration, appraisal and production from such a tight oil sandstone, the diagenesis and reservoir quality must be thoroughly studied first. The tight oil sandstone has been examined by a variety of methods, including core and thin section observation, XRD, SEM, CL, fluorescence, electron probing analysis, fluid inclusion and isotope testing and quantitative determination of reservoir properties. The sandstones are mostly lithic arkoses and feldspathic litharenites with fine to medium grain size and moderate to good sorting. The sandstones are dominated by feldspar, quartz, and volcanic rock fragments showing various stages of disintegration. The reservoir properties are quite poor, with low porosity (average 8.54%) and permeability (average 0.493 mD), small pore-throat radius (average 0.206 μm) and high displacement pressure (mostly higher than 1 MPa). The tight sandstone reservoirs have undergone significant diagenetic alterations such as compaction, feldspar dissolution, quartz cementation, carbonate cementation (mainly ferrocalcite and ankerite) and clay mineral alteration. As to the onset time, the oil emplacement was prior to the carbonate cementation but posterior to the quartz cementation and feldspar dissolution. The smectite to illite reaction and pressure solution at stylolites provide a most important silica sources for quartz cementation. Carbonate cements increase towards interbedded mudstones. Mechanical compaction has played a more important role than cementation in destroying the reservoir quality of the K1q4 sandstone reservoirs. Mixed-layer illite/smectite and illite reduced the porosity and permeability significantly, while chlorite preserved the porosity and permeability since it tends to be oil wet so that later carbonate cementation can be inhibited to some extent. It is likely that the oil emplacement occurred

  10. Complex permeability structure of a fault zone crosscutting a sequence of sandstones and shales and its influence on hydraulic head distribution

    NASA Astrophysics Data System (ADS)

    Cilona, A.; Aydin, A.; Hazelton, G.

    2013-12-01

    Characterization of the structural architecture of a 5 km-long, N40°E-striking fault zone provides new insights for the interpretation of hydraulic heads measured across and along the fault. Of interest is the contaminant transport across a portion of the Upper Cretaceous Chatsworth Formation, a 1400 m-thick turbidite sequence of sandstones and shales exposed in the Simi Hills, south California. Local bedding consistently dips about 20° to 30° to NW. Participating hydrogeologists monitor the local groundwater system by means of numerous boreholes used to define the 3D distribution of the groundwater table around the fault. Sixty hydraulic head measurements consistently show differences of 10s of meters, except for a small area. In this presentation, we propose a link between this distribution and the fault zone architecture. Despite an apparent linear morphological trend, the fault is made up of at least three distinct segments named here as northern, central and southern segments. Key aspects of the fault zone architecture have been delineated at two sites. The first is an outcrop of the central segment and the second is a borehole intersecting the northern segment at depth. The first site shows the fault zone juxtaposing sandstones against shales. Here the fault zone consists of a 13 meter-wide fault rock including a highly deformed sliver of sandstone on the northwestern side. In the sandstone, shear offset was resolved along N42°E striking and SE dipping fracture surfaces localized within a 40 cm thick strand. Here the central core of the fault zone is 8 m-wide and contains mostly shale characterized by highly diffuse deformation. It shows a complex texture overprinted by N30°E-striking carbonate veins. At the southeastern edge of the fault zone exposure, a shale unit dipping 50° NW towards the fault zone provides the key information that the shale unit was incorporated into the fault zone in a manner consistent with shale smearing. At the second site, a

  11. Depositional environments and sand body morphologies of the muddy sandstones at Kitty Field, Powder River Basin, Wyoming

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Larberg, G.M.B.

    1980-01-01

    Lower Cretaceous muddy sandstones form a stratigraphic trap at Kitty Field, Campbell County, Wyoming. Porosity and permeability are generally low, but the best reservoir develop maximum effective porosity of 17% and maximum permeability of 442 md. Reservoirs sandstones average less than 15 ft and rarely exceed 30 ft in thickness. Ultimate recovery from the field is estimated at 23 million bbl. Based on electric log character, 4 easily recognizable zones within the muddy interval at Kitty were numbered one through 4 in slabbed cores and petrographic analyses of selected core samples, suggest that sandstones in the second, third, and fourthmore » muddy zones were deposited as part of a sequence associated with the overall transgression of the lower Cretaceous sea. Fourth zone sandstones are fluvial in origin, and were deposited in lows on the unconformable surface of the underlying skull creek shale. 18 references.« less

  12. Zeolites in the Miocene Briones Sandstone and related formations of the central Coast Ranges, California

    USGS Publications Warehouse

    Murata, K.J.; Whiteley, Karen R.

    1973-01-01

    Authigenic zeolites present in the generally tuffaceous Miocene Briones Sandstone and related formations of the central Coast Ranges of California indicate three stages of diagenetic history: (1) Initial alteration of pyroclastic materials to clinoptilolite (and montmorillonite) that is widely distributed in small amounts throughout the region. (2) Subsequent crystallization of heulandite followed by stilbite in fractures at a few places. (3) Widespread development of laumontite in only the southern part of the region, where the sandstone appears to have been downfolded and faulted to greater depths than elsewhere. Laumontite occurs both as pervasive cement of sandstone and as filling of fractures, and was produced through the reaction of interstitial solutions with other zeolites and with such major constituents of the sandstone as plagioclase, montmorillonite, and calcite at temperatures of 100° C or higher. Mordenite was found at only one locality, closely associated with clinoptilolite and opal. Analcite occurs in diverse settings, and its relation to the other zeolites is obscure.  Sparry calcite and coexisting stilbite, laumontite, or analcite in veins seem to make up nonequilibrium assemblages.

  13. Transport of Organic Contaminants Mobilized from Coal through Sandstone Overlying a Geological Carbon Sequestration Reservoir

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zhong, Lirong; Cantrell, Kirk J.; Bacon, Diana H.

    2014-02-01

    Column experiments were conducted using a wetted sandstone rock installed in a tri-axial core holder to study the flow and transport of organic compounds mobilized by scCO2 under simulated geologic carbon storage (GCS) conditions. The sandstone rock was collected from a formation overlying a deep saline reservoir at a GCS demonstration site. Rock core effluent pressures were set at 0, 500, or 1000 psig and the core temperature was set at 20 or 50°C to simulate the transport to different subsurface depths. The concentrations of the organic compounds in the column effluent and their distribution within the sandstone core weremore » monitored. Results indicate that the mobility though the core sample was much higher for BTEX compounds than for naphthalene. Retention of organic compounds from the vapor phase to the core appeared to be primarily controlled by partitioning from the vapor phase to the aqueous phase. Adsorption to the surfaces of the wetted sandstone was also significant for naphthalene. Reduced temperature and elevated pressure resulted in greater partitioning of the mobilized organic contaminants into the water phase.« less

  14. Pore water evolution in sandstones of the Groundhog Coalfield, northern Bowser Basin, British Columbia

    NASA Astrophysics Data System (ADS)

    Cookenboo, H. O.; Bustin, R. M.

    1999-01-01

    The succession of sandstone cements in chert and volcanic lithic arenites and wackes from the northern Bowser Basin of British Columbia comprises a record of diagenesis in shallow marine, deltaic, and coastal plain siliciclastic sediments that pass through the oil window and reach temperatures near the onset of metamorphism. The succession of cements is consistent with seawater in the sandstones mixing with acid waters derived from dewatering of interbedded organic rich muds. Sandstone cement paragenesis includes seven discrete cement stages. From earliest to latest the cement stages are: (1) pore-lining chlorite; (2) pore-lining to pore-filling illite; (3) pore-filling kaolinite; (4) oil migration through some of the remaining connected pores; (5) chlorite dissolution; (6) quartz cement; and (7) calcite cement. These seven cement stages are interpreted as a record of the evolution of pore waters circulating through the sandstones after burial. The earliest cement stages, as well as the depositional environments, are compatible with seawater as the initial pore fluid. Seawater composition changed during transport through the sandstones, first by loss of Mg 2+ and Fe 2+ during chlorite precipitation (stage 1). Dewatering of interbedded organic-rich mudstones probably added Mg 2+ and Fe 2+ to partially buffer the loss of these cations to chlorite. Acids produced during breakdown of organic matter are presumed to have mixed into sandstone pore fluids due to further compaction of the muds, leading to reduction of initial alkalinity. Reduction in alkalinity, in turn, favours change from chlorite to illite precipitation (stage 2), and finally to kaolinite (stage 3). Pore waters likely reached their peak acidity at the time of oil migration (stage 4). Chlorite dissolution (stage 5) and quartz precipitation (stage 6) occurred when pores were filled by these hydrocarbon-bearing and presumably acidic fluids. Fluid inclusions in fracture-filling quartz cements contain

  15. Axial and Radial Permeability Evolutions of Compressed Sandstones: End Effects and Shear-band Induced Permeability Anisotropy

    NASA Astrophysics Data System (ADS)

    Dautriat, Jeremie; Gland, Nicolas; Guelard, Jean; Dimanov, Alexandre; Raphanel, Jean L.

    2009-07-01

    The influence of hydrostatic and uniaxial stress states on the porosity and permeability of sandstones has been investigated. The experimental procedure uses a special triaxial cell which allows permeability measurements in the axial and radial directions. The core sleeve is equipped with two pressure samplers placed distant from the ends. They provide mid-length axial permeability measure as opposed to the overall permeability measure, which is based on the flow imposed through the pistons of the triaxial cell. The core sleeve is also equipped to perform flows in two directions transverse to the axis of the sample. Two independent measures of axial and complementary radial permeability are thus obtained. Both Fontainebleau sandstone specimens with a porosity of about 5.8% to 8% and low permeability ranging from 2.5 mD to 30 mD and Bentheimer sandstone with a porosity of 24% and a high permeability of 3 D have been tested. The initial axial permeability values obtained by each method are in good agreement for the Fontainebleau sandstone. The Bentheimer sandstone samples present an axial mid-length permeability 1.6 times higher than the overall permeability. A similar discrepancy is also observed in the radial direction, also it relates essentially to the shape of flow lines induced by the radial flow. All the tested samples have shown a higher stress dependency of overall and radial permeability than mid-length permeability. The effect of compaction damage at the pistons/sample and radial ports/sample interfaces is discussed. The relevance of directional permeability measurements during continuous uniaxial compression loadings has been shown on the Bentheimer sandstone until the failure of the sample. We can efficiently measure the influence of brittle failure associated to dilatant regime on the permeability: It tends to increase in the failure propagation direction and to decrease strongly in the transverse direction.

  16. The effect of grain size and cement content on index properties of weakly solidified artificial sandstones

    NASA Astrophysics Data System (ADS)

    Atapour, Hadi; Mortazavi, Ali

    2018-04-01

    The effects of textural characteristics, especially grain size, on index properties of weakly solidified artificial sandstones are studied. For this purpose, a relatively large number of laboratory tests were carried out on artificial sandstones that were produced in the laboratory. The prepared samples represent fifteen sandstone types consisting of five different median grain sizes and three different cement contents. Indices rock properties including effective porosity, bulk density, point load strength index, and Schmidt hammer values (SHVs) were determined. Experimental results showed that the grain size has significant effects on index properties of weakly solidified sandstones. The porosity of samples is inversely related to the grain size and decreases linearly as grain size increases. While a direct relationship was observed between grain size and dry bulk density, as bulk density increased with increasing median grain size. Furthermore, it was observed that the point load strength index and SHV of samples increased as a result of grain size increase. These observations are indirectly related to the porosity decrease as a function of median grain size.

  17. Waterborne Superhydrophobic and Superoleophobic Coatings for the Protection of Marble and Sandstone

    PubMed Central

    Aslanidou, Dimitra; Lampakis, Dimitrios

    2018-01-01

    Silica nanoparticles were dispersed in an aqueous emulsion of alkoxy silanes and organic fluoropolymer. The dispersion was sprayed onto white marble and sandstone. The deposited composite coatings exhibited (i) superhydrophobicity and superoleophobicity, as evidenced by the high (>150°) static contact angles of water and oil drops as well as (ii) water and oil repellency according to the low (<7°) corresponding tilt contact angles. Apart from marble and sandstone, the coatings with extreme wetting properties were deposited onto concrete, silk, and paper, thus demonstrating the versatility of the method. The siloxane/fluoropolymer product was characterized using Fourier Transform Infrared Spectroscopy (FT-IR), Raman spectroscopy and Scanning Electron Microscopy equipped with an Energy Dispersive X-ray Spectrometer (SEM-EDX). Moreover, SEM and FT-IR were used to reveal the surface structures of the composite coatings and their transition from superhydrophobicity to superhydrophilicity which occurred after severe thermal treatment. The composite coatings slightly reduced the breathability of marble and sandstone and had practically no optical effect on the colour of the two stones. Moreover, the coatings offered good protection against water penetration by capillarity. PMID:29642652

  18. The Role of Authigenic (pigment) Hematite in Controlling the Remanence, Rock Magnetic, and Magnetic Fabric Properties of Red Beds--If You Have Seen One Red Bed, You Certainly Have Not Seen Them All!

    NASA Astrophysics Data System (ADS)

    Geissman, J. W.

    2014-12-01

    Discussion continues on the relative role of authigenic (pigment) fine-grained hematite, relative to detrital, considerably coarser specular hematite (specularite) as a carrier of geologically meaningful remanence, as a determinant of rock magnetic properties, and as a contributor to magnetic fabrics in red beds. For one, many workers commonly assume that the laboratory unblocking temperature spectra (Tlub) of a red bed dominated by authigenic pigment does not reach the maximum Tlub as approximated by the Neel temperature (~948 K) because of the ultra fine grain size of the pigment. This issue was discussed as recently as the IRM Santa Fe meeting in late June, 2014. Many laboratories routinely utilize chemical demagnetization in concert with progressive thermal demagnetization to attempt to assess the relative role of pigment vs. detrital hematite. However, the utility of chemical demagnetization has been long challenged. In studying the anisotropy of magnetic susceptibility and remanence in red beds, recent work has considered separating the contributions of both types of hematite to the fabric signal. Three different red bed "types" (siltstones of the Triassic Chugwater Group, Gros Ventre Range, Wyoming; mudrocks of lowermost Triassic Quartermaster Formation, west Texas; and siltstones to medium sandstones of Upper Cretaceous age, northwest Vietnam) are used to evaluate the effects of varying contributions by pigment hematite to remanence, rock magnetic, and magnetic fabric properties. All rocks are well-characterized petrographically, so that the modal abundance of detrital oxides is known. The Chugwater siltstones are notable because of a relatively low Tlub spectra (below about 620o C), with no evidence of a low coercivity cubic phase. Rock magnetic and magnetic fabric properties are monitored as a function of progressive chemical demagnetization to further elucidate the role of hematite pigment in rocks that have contributed much to the paleomagnetic record

  19. Diagenetic history of the Surma Group sandstones (Miocene) in the Surma Basin, Bangladesh

    NASA Astrophysics Data System (ADS)

    Rahman, M. Julleh Jalalur; McCann, Tom

    2012-02-01

    This study examines the various diagenetic controls of the Miocene Surma Group sandstones encountered in petroleum exploration wells from the Surma Basin, which is situated in the northeastern part of the Bengal Basin, Bangladesh. The principal diagenetic minerals/cements in the Surma Group sandstones are Fe-carbonates (with Fe-calcite dominating), quartz overgrowths and authigenic clays (predominantly chlorite, illite-smectite and minor kaolin). The isotopic composition of the carbonate cement revealed a narrow range of δ 18O values (-10.3‰ to -12.4‰) and a wide range of δ 13C value (+1.4‰ to -23.1‰). The δ 13C VPDB and δ 18O VPDB values of the carbonate cements reveal that carbon was most likely derived from the thermal maturation of organic matter during burial, as well as from the dissolution of isolated carbonate clasts and precipitated from mixed marine-meteoric pore waters. The relationship between the intergranular volume (IGV) versus cement volume indicates that compaction played a more significant role than cementation in destroying the primary porosity. However, cementation also played a major role in drastically reducing porosity and permeability in sandstones with poikilotopic, pore-filling blocky cements formed in early to intermediate and deep burial areas. In addition to Fe-carbonate cements, various clay minerals including illite-smectite and chlorite occur as pore-filling and pore-lining authigenic phases. Significant secondary porosity has been generated at depths from 2500 m to 4728 m. The best reservoir rocks found at depths of 2500-3300 m are well sorted, relatively coarse grained; more loosely packed and better rounded sandstones having good porosities (20-30%) and high permeabilities (12-6000 mD). These good quality reservoir rocks are, however, not uniformly distributed and can be considered to be compartmentalized as a result of interbedding with sandstone layers of low to moderate porosities, low permeabilities owing to poor

  20. Remote detection of fluid-related diagenetic mineralogical variations in the Wingate Sandstone at different spatial and spectral resolutions

    NASA Astrophysics Data System (ADS)

    Okyay, Unal; Khan, Shuhab D.

    2016-02-01

    Well-exposed eolian units of the Jurassic system on the Colorado Plateau including the Wingate Sandstone, show prominent color variations throughout southeastern Utah due to diagenetic changes that include precipitation and/or removal of iron oxide, clay, and carbonate cement. Spatially variable characteristic diagenetic changes suggest fluid-rock interactions through the sandstone. Distinctive spectral signatures of diagenetic minerals can be used to map diagenetic mineral variability and possibly fluid-flow pathways. The main objective of this work was to identify characteristic diagenetic minerals, and map their spatial variability from regional to outcrop scale in Wingate Sandstone exposures of Lisbon Valley, Utah. Laboratory reflectance spectroscopy analysis of the samples facilitated identification of diagnostic spectral characteristics of the common diagenetic minerals and their relative abundances between altered and unaltered Wingate Sandstone. Comparison of reflectance spectroscopy with satellite, airborne, and ground-based imaging spectroscopy data provided a method for mapping and evaluating spatial variations of diagenetic minerals. The Feature-oriented Principal Component Selection method was used on Advanced Spaceborne Thermal Emission and Reflection Radiometer data so as to map common mineral groups throughout the broader Wingate Sandstone exposure in the area. The Minimum Noise Fraction and Spectral Angle Mapper methods were applied on airborne HyMap and ground-based hyperspectral imaging data to identify and map mineralogical changes. The satellite and airborne data showed that out of 25.55 km2 total exposure of Wingate Sandstone in Lisbon Valley, unaltered sandstone cover 12.55 km2, and altered sandstone cover 8.90 km2 in the northwest flank and 5.09 km2 in the southern flank of the anticline. The ground-based hyperspectral data demonstrated the ability to identify and map mineral assemblages with two-dimensional lateral continuity on near

  1. Geology and oil and gas assessment of the Todilto Total Petroleum System, San Juan Basin Province, New Mexico and Colorado: Chapter 3 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

    USGS Publications Warehouse

    Ridgley, J.L.; Hatch, J.R.

    2013-01-01

    Organic-rich, shaly limestone beds, which contain hydrocarbon source beds in the lower part of the Jurassic Todilto Limestone Member of the Wanakah Formation, and sandstone reservoirs in the overlying Jurassic Entrada Sandstone, compose the Todilto Total Petroleum System (TPS). Source rock facies of the Todilto Limestone were deposited in a combined marine-lacustrine depositional setting. Sandstone reservoirs in the Entrada Sandstone were deposited in eolian depositional environments. Oil in Todilto source beds was generated beginning in the middle Paleocene, about 63 million years ago, and maximum generation of oil occurred in the middle Eocene. In the northern part of the San Juan Basin, possible gas and condensate were generated in Todilto Limestone Member source beds until the middle Miocene. The migration distance of oil from the Todilto source beds into the underlying Entrada Sandstone reservoirs was short, probably within the dimensions of a single dune crest. Traps in the Entrada are mainly stratigraphic and diagenetic. Regional tilt of the strata to the northeast has influenced structural trapping of oil, but also allowed for later introduction of water. Subsequent hydrodynamic forces have influenced the repositioning of the oil in some reservoirs and flushing in others. Seals are mostly the anhydrite and limestone facies of the Todilto, which thin to as little as 10 ft over the crests of the dunes. The TPS contains only one assessment unit, the Entrada Sandstone Conventional Oil Assessment Unit (AU) (50220401). Only four of the eight oil fields producing from the Entrada met the 0.5 million barrels of oil minimum size used for this assessment. The AU was estimated at the mean to have potential additions to reserves of 2.32 million barrels of oil (MMBO), 5.56 billion cubic feet of natural gas (BCFG), and 0.22 million barrels of natural gas liquids (MMBNGL).

  2. Infant's bed climate and bedding in the Japanese home.

    PubMed

    Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

    2012-06-01

    to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

  3. Evaluation of stratigraphic relations of sandstone-producing reservoirs in upper Council Grove and Chase groups (Permian) in north-central Oklahoma

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chaplin, J.R.

    1989-08-01

    Poor well control and the absence of surface stratigraphic control made previous interpretations of the stratigraphic relations of sandstone-producing reservoirs tenuous. Recent extensive analyses of surface outcrops and well and core data support the contention that the major sandstone-producing reservoirs can be physically correlated with formations in the outcrop section. Sandstone bodies within the upper Council Grove Group include Neva sand and Blackwell sand (Neva Limestone), Hotson-Kisner sand (Eskridge Shale), and the Whitney-Hodges sand. The Whitney-Hodges sand correlates, in part, with the Speiser Shale (Garrison Formation) of the outcrop section. However, previous usage suggested tentative correlations with sandstone bodies stratigraphicallymore » lower in the section. These sands were probably deposited in channels that were, in part, fluvial, tidal, or estuarine. Production from the Chase Group occurs locally within channelform sandstone bodies referred to as the Hoy-Matfield sand. These sands appear to be equivalent, occupying essentially the position of the Kinney Limestone Member (Matfield Shale) of the outcrop section. Detailed core-hole data at and in the vicinity of Kaw Dam, southeastern Kay County, and outcrops along the shoreline of Kaw Lake at Kaw City, Kay County, clearly demonstrate the facies distribution of the Hoy sand. Core-hole data has also delineated additional potential sandstone reservoirs within and near or at the top of the Fort Riley Limestone Member (Barneston Limestone). The Wolfe sand, a producing sandstone locally, occupies a stratigraphic position within the Doyle Shale.« less

  4. Subdivision of the Cambrian-Ordovician Upper Sandstone Aquifer'' in the Fox Cities area, east-central Wisconsin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Erikson, K.A.; Smith, G.L.

    The informally-named Upper Sandstone Aquifer,'' a lithologically heterogeneous unit, has been subdivided into three thinner hydrostratigraphic units, the Upper Cambrian Jordan Formation (sandstone), the Lower Ordovician Prairie du Chien Group (dolomite), and the Middle Ordovician St. Peter Formation (mostly sandstone). Reevaluation of the Upper Sandstone Aquifer'' in the Fox Cities area (Appleton, Neenah, Menasha) was based on detailed analysis of 125 geologic well logs and 200 well-construction reports. Isopach maps and geologic cross-sections of these units in the Fox Cities area show extreme variations in thickness over short lateral distances. Although the Jordan Formation has a uniform thickness of 13more » m (40 ft), the Prairie du Chien Group varies from 0--88 m (0--275 ft). The St. Peter Formation varies in thickness from 0--108 m (0--335 ft). The Prairie du Chien Group is relatively thin or absent in the Fox Cities area in locations where the overlying St. Peter Formation is relatively thick. St Peter can be further subdivided into Readstown, Tonti, and Glenwood Members. The Readstown Member is a lithologically heterogeneous unit of variable thickness and distribution. The Tonti Member is a poorly cemented, fine-medium quartz arenite with which is lumped the Glenwood Member, a conglomeratic, silty medium-coarse sandstone. Maximum St. Peter thicknesses represent filled paleokarst depressions developed on top of the Prairie du Chien Group, with profound implications for estimates of hydraulic conductivity.« less

  5. 7 CFR 3201.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

  6. 7 CFR 2902.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

  7. 7 CFR 3201.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

  8. 7 CFR 3201.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... group of woven cloth products used as coverings on a bed. Bedding includes products such as blankets, bedspreads, comforters, and quilts. (2) Bed linens are woven cloth sheets and pillowcases used in bedding. (3) Towels are woven cloth products used primarily for drying and wiping. (b) Minimum biobased content. The...

  9. Sedimentological and Stratigraphic Controls on Natural Fracture Distribution in Wajid Group, SW Saudi Arabia

    NASA Astrophysics Data System (ADS)

    Benaafi, Mohammed; Hariri, Mustafa; Abdullatif, Osman; Makkawi, Mohammed; Korvin, Gabor

    2016-04-01

    The Cambro-Permian Wajid Group, SW Saudi Arabia, is the main groundwater aquifer in Wadi Al-Dawasir and Najran areas. In addition, it has a reservoir potentiality for oil and natural gas in Rub' Al-Khali Basin. Wajid Group divided into four formations, ascending Dibsiyah, Sanamah, Khussyayan and Juwayl. They are mainly sandstone and exposed in an area extend from Wadi Al-Dawasir southward to Najran city and deposited within fluvial, shallow marine and glacial environments. This study aims to investigate the sedimentological and stratigraphic controls on the distribution of natural fractures within Wajid Group outcrops. A scanline sampling method was used to study the natural fracture network within Wajid Group outcrops, where the natural fractures were measured and characterized in 12 locations. Four regional natural fracture sets were observed with mean strikes of 050o, 075o, 345o, and 320o. Seven lithofacies characterized the Wajid Group at these locations and include fine-grained sandstone, coarse to pebbly sandstone, cross-bedded sandstone, massive sandstone, bioturbated sandstone, conglomerate sandstone, and conglomerate lithofacies. We found that the fine-grained and small scale cross-bedded sandstones lithofacies are characterized by high fracture intensity. In contrast, the coarse-grained sandstone and conglomerate lithofacies have low fracture intensity. Therefore, the relative fracture intensity and spacing of natural fractures within Wajid Group in the subsurface can be predicted by using the lithofacies and their depositional environments. In terms of stratigraphy, we found that the bed thickness and the stratigraphic architecture are the main controls on fractures intensity. The outcomes of this study can help to understand and predict the natural fracture distribution within the subsurface fractured sandstone hosting groundwater and hydrocarbon in Wajid and Rub' Al-Khali Basins. Hence, the finding of this study might help to explore and develop the

  10. Progress report on the Happy Jack mine, Which Canyon area, San Juan county, Utah

    USGS Publications Warehouse

    Trites, Albert F.; Chew, Randall T.

    1954-01-01

    The Happy Jack mine is in the White Canyon area, San Juan county, Utah. Production is from high-grade uranium deposits in the Shinarump conglomerate of the Triassic age. In this area the Shinarump beds range from about 16 to 40 feet in thickness and the lower part of these beds fills an east-trending channel this is note than 750 feet wide and 10 feet deep. The Shinarump conglomerate consists of beds of coarse- to fine-grained quartzose sandstone, conglomerate, siltstone, and claystone. Carbonized wood is abundant in these beds, and in the field it was classified as mineral charcoal and coal. Intra-Shinarump channels, cross-stratification, current lineation, and slumping and compaction structures have been recognized in the mine. Steeply dipping fractures have dominant trends in four directions -- N 65°W, N 60°E, N 85°E, and due north. Uranium occurs as bedded deposits, as replacement bodies in accumulations of "trash", and as replacements of larger fragments of wood. An "ore shoot" is formed where the three types of uranium deposits occur together; these ore shoots appear to be elongate masses with sharp boundaries. Uranium minerals include uraninite, sooty pitchblende(?), and the sulfate--betazippeite, johannite, and uranopilite. Associated with the uraninite are the sulfide minerals covellite, bornite, chalcopyritw, and pyrite. Galena and sphalerite have been found in close association with uranium minerals. The gaunge minerals include: limonite and hematite present in most of the sandstone beds throughout the deposit, jarosite that impregnates much of the sandstone in the outer parts of the mine workings, gypsum that fills many of the fractures, and barite that impregnates the sandstone in at least one part of the mine. Secondary copper minerals, mainly copper sulfates, occur throughout the mine, but most abundant near the adits in the outermost 30 feet of the workings. The minerals comprising the bulk of the country rock include quartz, feldspar, and clay

  11. Lower Jurassic Navaho-Aztec-Equivalent Sandstones in southern Arizona and their paleogeographic significance

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bilodeau, W.L.; Keith, S.B.

    1986-06-01

    Thick sequences of Lower Jurassic rhyolitic and andesitic volcanic rocks in several mountain ranges of southern Arizona contain interbedded quartzarenites. Locally up to 250 m thick, these sandstone lenses, composed of well-sorted and well-rounded quartz grains, commonly contain large-scale cross-stratification and are considered to be eolian sand deposits. The eolian sands were blown up against the continental side of the Early Jurassic volcanic arc that trended northwest-southeast across the southwestern margin of the North American continent and/or plate at that time. Paleocurrent data suggest southerly eolian transport of the sands from the Colorado Plateau area. Correlation of these sandstones withmore » the Lower Jurassic Navaho and Aztec Sandstones is indicated by the paleocurrent data as well as radiometric dating of the interbedded volcanics. Eolian sand transport southward across central Arizona in the Early Jurassic indicates that the Mogollon highlands either did not then exist, or were merely low, discontinuous inselbergs on a broad back-arc ramp, more appropriately called the Mogollon slope.« less

  12. Discriminant function analysis as tool for subsurface geologist

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Chesser, K.

    1987-05-01

    Sedimentary structures such as cross-bedding control porosity, permeability, and other petrophysical properties in sandstone reservoirs. Understanding the distribution of such structures in the subsurface not only aids in the prediction of reservoir properties but also provides information about depositional environments. Discriminant function analysis (DFA) is a simple yet powerful method incorporating petrophysical data from wireline logs, core analyses, or other sources into groups that have been previously defined through direct observation of sedimentary structures in cores. Once data have been classified into meaningful groups, the geologist can predict the distribution of specific sedimentary structures or important reservoir properties in areasmore » where cores are unavailable. DFA is efficient. Given several variables, DFA will choose the best combination to discriminate among groups. The initial classification function can be computed from relatively few observations, and additional data may be included as necessary. Furthermore, DFA provides quantitative goodness-of-fit estimates for each observation. Such estimates can be used as mapping parameters or to assess risk in petroleum ventures. Petrophysical data from the Skinner sandstone of Strauss field in southeastern Kansas tested the ability of DFA to discriminate between cross-bedded and ripple-bedded sandstones. Petroleum production in Strauss field is largely restricted to the more permeable cross-bedded sandstones. DFA based on permeability correctly placed 80% of samples into cross-bedded or ripple-bedded groups. Addition of formation factor to the discriminant function increased correct classifications to 83% - a small but statistically significant gain.« less

  13. Bed load transport in gravel-bed rivers

    Treesearch

    Jeffrey J. Barry

    2007-01-01

    Bed load transport is a fundamental physical process in alluvial rivers, building and maintaining a channel geometry that reflects both the quantity and timing of water and the volume and caliber of sediment delivered from the watershed. A variety of formulae have been developed to predict bed load transport in gravel-bed rivers, but testing of the equations in natural...

  14. A preliminary report on a zone containing thick lignite beds, Denver Basin, Colorado

    USGS Publications Warehouse

    Soister, Paul E.

    1973-01-01

    A zone of lignite beds of Paleocene age in the Denver Formation (Upper Cretaceous and Paleocene) lies about 800-1,500 feet above the well-known and extensively mined coal beds of the Laramie Formation (Upper Cretaceous). The zone is a few hundred to as much as 500 feet thick. Where lignite beds lie within 1,000 feet of the surface, this zone underlies an area about 30 miles wide by about 75 miles long, stretching from just northeast of Denver to several miles south of Calhan. Fifteen mines were operated at various periods between 1874 and 1940 and probably produced a total of less than 100,000 tons of lignite, mostly for local use. From 1874 to 1974, several geologists have reported on this lignite zone or the enclosing beds, but no detailed reports have been written except for one by this writer. Drill holes are the main source of geologic data, owing to poor exposure. There are generally about 3 to 6 lignite beds, and they are mostly about 15 or 20 to a few tens of feet apart. Most or all beds typically contain numerous non-coal partings from a fraction of an inch to several inches thick, so that thickness of lignite beds should be stated as gross thickness and as net lignite thickness; net lignite thickness is generally from 70 to 90 percent of gross thickness. Many partings are composed of kaolin, but others are composed of other clay minerals, siltstone, and sandstone. The lignite beds range generally from 1 or 2 to several feet thick, and some are as much as 10-25 feet thick; the thickest known bed has a maximum thickness of 54.5 feet, with a net lignite thickness of 40 feet. Most lignite beds seem to have fair lateral continuity, and at least some beds are several miles in extent. The thickest known lignite bed was traced for at least 18 miles, from northwest to southeast of Watkins. The lignite is brownish-black to black, weathers, checks, and disintegrates rapidly, and even in drill cores from a few hundred feet in depth the lignite is easily broken by

  15. Carbon dioxide/brine wettability of porous sandstone versus solid quartz: An experimental and theoretical investigation.

    PubMed

    Alnili, Firas; Al-Yaseri, Ahmed; Roshan, Hamid; Rahman, Taufiq; Verall, Michael; Lebedev, Maxim; Sarmadivaleh, Mohammad; Iglauer, Stefan; Barifcani, Ahmed

    2018-08-15

    Wettability plays an important role in underground geological storage of carbon dioxide because the fluid flow and distribution mechanism within porous media is controlled by this phenomenon. CO 2 pressure, temperature, brine composition, and mineral type have significant effects on wettability. Despite past research on this subject, the factors that control the wettability variation for CO 2 /water/minerals, particularly the effects of pores in the porous substrate on the contact angle at different pressures, temperatures, and salinities, as well as the physical processes involved are not fully understood. We measured the contact angle of deionised water and brine/CO 2 /porous sandstone samples at different pressures, temperatures, and salinities. Then, we compared the results with those of pure quartz. Finally, we developed a physical model to explain the observed phenomena. The measured contact angle of sandstone was systematically greater than that of pure quartz because of the pores present in sandstone. Moreover, the effect of pressure and temperature on the contact angle of sandstone was similar to that of pure quartz. The results showed that the contact angle increases with increase in temperature and pressure and decreases with increase in salinity. Copyright © 2018 Elsevier Inc. All rights reserved.

  16. A method for automatic grain segmentation of multi-angle cross-polarized microscopic images of sandstone

    NASA Astrophysics Data System (ADS)

    Jiang, Feng; Gu, Qing; Hao, Huizhen; Li, Na; Wang, Bingqian; Hu, Xiumian

    2018-06-01

    Automatic grain segmentation of sandstone is to partition mineral grains into separate regions in the thin section, which is the first step for computer aided mineral identification and sandstone classification. The sandstone microscopic images contain a large number of mixed mineral grains where differences among adjacent grains, i.e., quartz, feldspar and lithic grains, are usually ambiguous, which make grain segmentation difficult. In this paper, we take advantage of multi-angle cross-polarized microscopic images and propose a method for grain segmentation with high accuracy. The method consists of two stages, in the first stage, we enhance the SLIC (Simple Linear Iterative Clustering) algorithm, named MSLIC, to make use of multi-angle images and segment the images as boundary adherent superpixels. In the second stage, we propose the region merging technique which combines the coarse merging and fine merging algorithms. The coarse merging merges the adjacent superpixels with less evident boundaries, and the fine merging merges the ambiguous superpixels using the spatial enhanced fuzzy clustering. Experiments are designed on 9 sets of multi-angle cross-polarized images taken from the three major types of sandstones. The results demonstrate both the effectiveness and potential of the proposed method, comparing to the available segmentation methods.

  17. Incised valley fill interpretation for Mississippian Black Hand Sandstone, Appalachian Basin, USA: Implications for glacial eustasy at Kinderhookian-Osagean (Tn2-Tn3) boundary

    USGS Publications Warehouse

    Matchen, D.L.; Kammer, T.W.

    2006-01-01

    Lower Mississippian strata of east-central Ohio are predominantly fine-grained marine deposits of the Cuyahoga and Logan formations. Within these sediments is the Black Hand Sandstone of the Cuyahoga Formation. The Black Hand Sandstone is a multistory, crossbedded, coarse-grained conglomeratic sandstone. The contact between the Black Hand Sandstone and the subjacent Cuyahoga Formation is sharp and scoured, with intraclasts of the Cuyahoga Formation incorporated into the basal Black Hand Sandstone. The Black Hand Sandstone was previously thought to represent a distributary channel deposit; however, the combination of lithofacies and architectural elements indicates deposition in a braided stream setting. The Cuyahoga Formation was deposited in a shallow marine setting. The erosional basal contact of the Black Hand Sandstone and the juxtaposition of fluvial and marine sediments suggests a sequence boundary. The geographic distribution of the Black Hand Sandstone combined with the evidence for a sequence boundary suggests deposition in an incised valley. The age of the Black Hand Sandstone is key to inferring the causes of valley incision. The Black Hand Sandstone is nearly devoid of body fossils, necessitating a biostratigraphic analysis of the surrounding Cuyahoga and Logan formations. Analysis indicates the Logan Formation is early Osagean age. Data from the Cuyahoga Formation suggest a Kinderhookian age with a possible transition to the Osagean in the uppermost Cuyahoga Formation. This constrains the age of the Black Hand Sandstone to the transition at the Kinderhookian-Osagean boundary. Recent reports indicate late Kinderhookian (Tournaisian, Tn2) Gondwanan glaciation based upon tillites and sharp excursions in stable-isotope curves. A glacio-eustatic fall in sea level is inferred to have caused incision of the Cuyahoga Formation, followed by deposition of the Black Hand Sandstone and Logan Formation during the subsequent sea level rise. The associated

  18. Discussion of case study of a stimulation experiment in a fluvial, tight-sandstone gas reservoir

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Azari, M.; Wooden, W.

    The authors found Warpinski et al.'s paper (Case Study of a Stimulation Experiment in Fluvial, Tight-Sandstone Gas Reservoir. Nov. 1990 SPE Production Engineering, Pages 403-10) to be very thorough and informative. That paper considered geological, logging, completion, and pressure-transient data to produce a comprehensive formation evaluation of a fluvial, tight-sandstone gas reservoir. The purpose of this paper is to present the author's view on the peculiar pressure-transient responses shown.

  19. Baked shale and slag formed by the burning of coal beds

    USGS Publications Warehouse

    Rogers, G. Sherburne

    1918-01-01

    The baking and reddening of large masses of strata caused by the burning of coal beds is a striking feature of the landscape in most of the great western coal-bearing areas. The general character and broader effects of the burning have been described by many writers, but the fact that in places enough heat is generated to fuse and thoroughly recrystallize the overlying shale and sandstone has received less attention. Some of the natural slags thus formed simulate somewhat abnormal igneous rocks, but others consist largely of rare and little known minerals. A wide range in the mineral composition of such slags is to be expected, depending on the composition of the original sediment and the conditions of fusion and cooling. These products of purely thermal metamorphism offer a fertile field for petrologic investigation. The writer has observed the effects produced by the burning of coal beds in several localities in Montana, particularly along upper Tongue River in the southern part of the State, in the district lying southeast of the mouth of Bighorn River, and in the Little Sheep Mountain coal field north of Miles City. A number of specimens of the rock formed have been examined under the microscope, though time has not been available for a systematic examination. The writer is greatly indebted to Mr. E. S. Larsen for assistance in the study of some of the minerals.

  20. Composition of weathering crusts on sandstones from natural outcrops and architectonic elements in an urban environment.

    PubMed

    Marszałek, Mariola; Alexandrowicz, Zofia; Rzepa, Grzegorz

    2014-12-01

    This work presents mineralogical and chemical characteristics of weathering crusts developed on sandstones exposed to various air pollution conditions. The samples have been collected from sandstone tors in the Carpathian Foothill and from buildings in Kraków. It has been stated that these crusts differ in both fabric and composition. The sandstone black crust from tors is rich in organic matter and composed of amorphous silica. Sulphate incrustations accompanied by dust particles have been only sometimes observed. Beneath the black crust, a zone coloured by iron (oxyhydr)oxides occurs. The enrichment of the surface crust in silica and iron compounds protects the rock interior from atmospheric impact. The sandstones from architectonic details are also covered by a thin carbon-rich black crust, but they are visibly loosened. Numerous salts, mainly gypsum and halite, crystallise here, thus enhancing deterioration of the rock. Moreover, spherical particles originated from industrial emissions are much more common. Gypsum in natural outcrops, forms isolated and well-developed crystals, whilst these found on the architectonic details are finer and densely cover the surface. Such diversity reflects various concentrations of acid air pollutants in solutions.

  1. The influence of temperature on brittle creep in sandstones

    NASA Astrophysics Data System (ADS)

    Heap, M. J.; Baud, P.; Meredith, P. G.; Vinciguerra, S.

    2009-04-01

    The characterization of time-dependent brittle rock deformation is fundamental to understanding the long-term evolution and dynamics of the Earth's upper crust. The presence of water promotes time-dependent deformation through environment-dependent stress corrosion cracking that allows rocks to deform at stresses far below their short-term failure stress. Here we report results from an experimental study of the influence of an elevated temperature on time-dependent brittle creep in water-saturated samples of Darley Dale (initial porosity of 13%), Bentheim (23%) and Crab Orchard (4%) sandstones. We present results from both conventional creep experiments (or ‘static fatigue' tests) and stress-stepping creep experiments performed under 20°C and 75°C and an effective confining pressure of 30 MPa (50 MPa confining pressure and a 20 MPa pore fluid pressure). The evolution of crack damage was monitored throughout each experiment by measuring the three proxies for damage (1) axial strain (2) pore volume change and (3) the output of AE energy. Conventional creep experiments have demonstrated that, for any given applied differential stress, the time-to-failure is dramatically reduced and the creep strain rate is significantly increased by application of an elevated temperature. Stress-stepping creep experiments have allowed us to investigate the influence of temperature in detail. Results from these experiments show that the creep strain rate for Darley Dale and Bentheim sandstones increases by approximately 3 orders of magnitude, and for Crab Orchard sandstone increases by approximately 2 orders of magnitude, as temperature is increased from 20°C to 75°C at a fixed effective differential stress. We discuss these results in the context of the different mineralogical and microstructural properties of the three rock types and the micro-mechanical and chemical processes operating on them.

  2. Bed Bugs

    EPA Pesticide Factsheets

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  3. Discolored Fracture Zones in Martian Sandstone

    NASA Image and Video Library

    2015-12-17

    This view from NASA's Curiosity Mars rover shows an example of discoloration closely linked to fractures in the Stimson formation sandstone on lower Mount Sharp. The pattern is evident along two perpendicular fractures. Curiosity's Navigation Camera (Navcam) acquired the component images of this mosaic on Aug. 23, 2015, during the 1.083rd Martian day, or sol, of the mission. The location is along the rover's path between "Marias Pass" and "Bridger Basin." In this region, the rover has found fracture zones to be associated with rock compositions enriched in silica, relative to surrounding bedrock. http://photojournal.jpl.nasa.gov/catalog/PIA20268

  4. Trace fossils and bioturbation in peritidal facies of the Potsdam-Theresa Formations (Cambrian-Ordovician), Northwest Adirondacks

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bjerstedt, T.W.; Erickson, J.M.

    The Cambrian-Ordovician Potsdam Sandstone, Theresa Formation, and Canadian correlatives in the St. Lawrence Lowlands preserve tide-dominated facies during the basal Cambrian transgression. Low intertidal sand flats in the upper Potsdam contain a Skolithos Ichnofacies dominated by Diplocraterion parallelum in clean, herringbone cross-bedded sandstones indicative of high tidal current energy. Wind-wave-driven longshore and tidal currents along a macrotidal coastline were funneled northeast-southwest by Precambrian topographic relief of up to 65 m. This relief is now expressed as the Thousand Islands of New York and Canada. The conformably overlying Theresa Formation preserves a shoaling-upward sequence of mixed clastic-carbonate facies. Shallow subtidal andmore » peritidal facies contain a mixed Skolithos-Cruziana Ichnofacies in sharply alternating lithofacies consisting of gray, intensely bioturbated, poorly sorted calcareous sandstone, and meter-thick, white cross-bedded sandstone. The parallelism between ichnofacies and lithofacies indicates that environmental energy level and persistence rather than water depth controlled trace fossil distribution. Bioturbated sandstones contain a Cruziana ichnofacies of abundant deposit feeders including: Fustiglyphus , Gyrochorte , Neonereites uniserialis , Phycodes flabellum, Planolites beverlyensis, Rosselia socialis, and Teichichnus. Suspension feeders are represented by D. habichi, D. parallelum, Skolithos, Monocraterion, and possibly Palaeophycus tubularis. Scavenging or deposit-feeding arthropods are represented by rare Cruziana furrows. Cross-bedded sandstones contain a Skolithos Ichnofacies of shallow Skolithos and Monocraterion burrows, and an undescribed large epistratal eurypterid( ) trail.« less

  5. Peering inside the granular bed: illuminating feedbacks between bed-load transport and bed-structure evolution

    NASA Astrophysics Data System (ADS)

    Houssais, M.; Jerolmack, D. J.; Martin, R. L.

    2013-12-01

    The threshold of motion is perhaps the most important quantity to determine for understanding rates of bed load transport, however it is a moving target. Decades of research show that it changes in space and in time within a river, and is highly variable among different systems; however, these differences are not mechanistically understood. Recent researchers have proposed that the critical Shields stress is strongly dependent on the local configuration of the sediment bed [Frey and Church, 2011]. Critical Shields stress has been observed to change following sediment-transporting flood events in natural rivers [e.g., Turowski et al., 2011], while small-scale laboratory experiments have produced declining bed load transport rates associated with slow bed compaction [Charru et al., 2004]. However, no direct measurements have been made of the evolving bed structure under bed load transport, so the connection between granular controls and the threshold of motion remains uncertain. A perspective we adopt is that granular effects determine the critical Shields stress, while the fluid supplies a distribution of driving stresses. In order to isolate the granular effect, we undertake laminar bed load transport experiments using plastic beads sheared by a viscous oil in a small, annular flume. The fluid and beads are refractive index matched, and the fluid impregnated with a fluorescing powder. When illuminated with a planar laser sheet, we are able to image slices of the granular bed while also tracking the overlying sediment transport. We present the first results showing how bed load transport influences granular packing, and how changes in packing influence the threshold of motion to feed back on bed load transport rates. This effect may account for much of the variability observed in the threshold of motion in natural streams, and by extension offers a plausible explanation for hysteresis in bed load transport rates observed during floods. Charru, F., H. Mouilleron, and

  6. Hydrological modelling in sandstone rocks watershed

    NASA Astrophysics Data System (ADS)

    Ponížilová, Iva; Unucka, Jan

    2015-04-01

    The contribution is focused on the modelling of surface and subsurface runoff in the Ploučnice basin. The used rainfall-runoff model is HEC-HMS comprising of the method of SCS CN curves and a recession method. The geological subsurface consisting of sandstone is characterised by reduced surface runoff and, on the contrary, it contributes to subsurface runoff. The aim of this paper is comparison of the rate of influence of sandstone on reducing surface runoff. The recession method for subsurface runoff was used to determine the subsurface runoff. The HEC-HMS model allows semi- and fully distributed approaches to schematisation of the watershed and rainfall situations. To determine the volume of runoff the method of SCS CN curves is used, which results depend on hydrological conditions of the soils. The rainfall-runoff model assuming selection of so-called methods of event of the SCS-CN type is used to determine the hydrograph and peak flow rate based on simulation of surface runoff in precipitation exceeding the infiltration capacity of the soil. The recession method is used to solve the baseflow (subsurface) runoff. The method is based on the separation of hydrograph to direct runoff and subsurface or baseflow runoff. The study area for the simulation of runoff using the method of SCS CN curves to determine the hydrological transformation is the Ploučnice basin. The Ploučnice is a hydrologically significant river in the northern part of the Czech Republic, it is a right tributary of the Elbe river with a total basin area of 1.194 km2. The average value of CN curves for the Ploučnice basin is 72. The geological structure of the Ploučnice basin is predominantly formed by Mesozoic sandstone. Despite significant initial loss of rainfall the basin response to the causal rainfall was demonstrated by a rapid rise of the surface runoff from the watershed and reached culmination flow. Basically, only surface runoff occures in the catchment during the initial phase of

  7. 20. Detail of sandstone pier under north line of trusses ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. Detail of sandstone pier under north line of trusses showing granite pier cap (darker stone) which supports the vertical strut. View to east. - Selby Avenue Bridge, Spanning Short Line Railways track at Selby Avenue between Hamline & Snelling Avenues, Saint Paul, Ramsey County, MN

  8. Digital Rock Physics Aplications: Visualisation Complex Pore and Porosity-Permeability Estimations of the Porous Sandstone Reservoir

    NASA Astrophysics Data System (ADS)

    Handoyo; Fatkhan; Del, Fourier

    2018-03-01

    Reservoir rock containing oil and gas generally has high porosity and permeability. High porosity is expected to accommodate hydrocarbon fluid in large quantities and high permeability is associated with the rock’s ability to let hydrocarbon fluid flow optimally. Porosity and permeability measurement of a rock sample is usually performed in the laboratory. We estimate the porosity and permeability of sandstones digitally by using digital images from μCT-Scan. Advantages of the method are non-destructive and can be applied for small rock pieces also easily to construct the model. The porosity values are calculated by comparing the digital image of the pore volume to the total volume of the sandstones; while the permeability values are calculated using the Lattice Boltzmann calculations utilizing the nature of the law of conservation of mass and conservation of momentum of a particle. To determine variations of the porosity and permeability, the main sandstone samples with a dimension of 300 × 300 × 300 pixels are made into eight sub-cubes with a size of 150 × 150 × 150 pixels. Results of digital image modeling fluid flow velocity are visualized as normal velocity (streamline). Variations in value sandstone porosity vary between 0.30 to 0.38 and permeability variations in the range of 4000 mD to 6200 mD. The results of calculations show that the sandstone sample in this research is highly porous and permeable. The method combined with rock physics can be powerful tools for determining rock properties from small rock fragments.

  9. The effect of weathering in the Buyukmelen River basin on the geochemistry of suspended and bed sediments and the hyrogeochemical characteristics of river water, Duzce, Turkey

    NASA Astrophysics Data System (ADS)

    Pehlivan, Rustem

    2010-07-01

    The Buyukmelen River is expected to be a water source that can supply the drinking water needs of Istanbul until 2040. The drinking and utility water needs of Istanbul are to transport water from the Buyukmelen River to Istanbul via pipeline and pump it into the Alibeykoy and Omerli reservoirs when their water levels drop. The Buyukmelen River is located in the province of Duzce in 170 km east of Istanbul and its water basin is approximately 2250 km 2. The Buyukmelen River flows muddy in the rainy season and into the Black Sea. The chemical compositions of natural waters alter due to interaction with geological formations, physical and chemical weathering of various rocks and the effects of mining and agricultural production. A research was conducted at the Buyukmelen River basin to determine the effects of hydrological processes. Therefore, the samples of rocks, soil, stream water, suspended and bed sediment were collected from the Buyukmelen River basin. Geochemical and water chemistry analyses of samples were performed at ALS Chemex laboratories, Canada. The bed sediments contain quartz, calcite, plagioclase, amphibole and clay minerals. The clay minerals in the suspended and bed sediment samples are kaolinite, smectite and illite. The water samples collected from the Aksu, Kucukmelen, Asarsu and Ugursuyu streams and the Buyukmelen River in winter (December 2005) and summer (June 2006) periods are rich in Ca and HCO 3 ions. The ions most abundant in rainfall sample are HCO 3 and Na. The ion compositions of surface waters have increased due to the weathering of limestone, agglomerate and volcanic sandstones, light acidic rainfall, semi-arid Black Sea climate in the Buyukmelen basin. The suspended sediment amount of the Buyukmelen River in the rainy season (December 2005) is 174 mg/l. According to the water contamination regulation of Turkey, the Buyukmelen Rivers belongs to quality class 4 based on Al ion and to quality class 3 based on Fe ion in winter period

  10. Provenance, diagenesis, tectonic setting and reservoir quality of the sandstones of the Kareem Formation, Gulf of Suez, Egypt

    NASA Astrophysics Data System (ADS)

    Zaid, Samir M.

    2013-09-01

    The Middle Miocene Kareem sandstones are important oil reservoirs in the southwestern part of the Gulf of Suez basin, Egypt. However, their diagenesis and provenance and their impact on reservoir quality, are virtually unknown. Samples from the Zeit Bay Oil Field, and the East Zeit Oil Field represent the Lower Kareem (Rahmi Member) and the Upper Kareem (Shagar Member), were studied using a combination of petrographic, mineralogical and geochemical techniques. The Lower Rahmi sandstones have an average framework composition of Q95F3.4R1.6, and 90% of the quartz grains are monocrystalline. By contrast, the Upper Shagar sandstones are only slightly less quartzose with an average framework composition of Q76F21R3 and 82% of the quartz grains are monocrystalline. The Kareem sandstones are mostly quartzarenite with subordinate subarkose and arkose. Petrographical and geochemical data of sandstones indicate that they were derived from granitic and metamorphic terrains as the main source rock with a subordinate quartzose recycled sedimentary rocks and deposited in a passive continental margin of a syn rift basin. The sandstones of the Kareem Formation show upward decrease in maturity. Petrographic study revealed that dolomite is the dominant cement and generally occurs as fine to medium rhombs pore occluding phase and locally as a grain replacive phase. Authigenic quartz occurs as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Authigenic anhydrites typically occur as poikilotopic rhombs or elongate laths infilling pores but also as vein filling cement. The kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene rocks. Diagenetic features include compaction; dolomite, silica and anhydrite cementation with minor iron-oxide, illite, kaolinite and pyrite cements; dissolution of feldspars, rock fragments. Silica dissolution, grain replacement and

  11. Control of bed height in a fluidized bed gasification system

    DOEpatents

    Mehta, Gautam I.; Rogers, Lynn M.

    1983-12-20

    In a fluidized bed apparatus a method for controlling the height of the fdized bed, taking into account variations in the density of the bed. The method comprises taking simultaneous differential pressure measurements at different vertical elevations within the vessel, averaging the differential pressures, determining an average fluidized bed density, then periodically calculating a weighting factor. The weighting factor is used in the determination of the actual bed height which is used in controlling the fluidizing means.

  12. Bed Bugs FAQs

    MedlinePlus

    ... Consultations, and General Public. Contact Us Parasites Home Bed Bugs FAQs Recommend on Facebook Tweet Share Compartir On ... are bed bugs treated and prevented? What are bed bugs? Bed bugs ( Cimex lectularius ) are small, flat, parasitic ...

  13. Source versus depositional controls on sandstone composition in a foreland basin: The El Imperial Formation (Mid Carboniferous-Lower Permian), San Rafael basin, western Argentina

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Espejo, E.S.; Lopez-Gamundi, O.R.

    1994-01-01

    The El Imperial Formation (mid-Carboniferous-Lower Permian) constitutes a progradational sandstone-rich succession deposited in the San Rafael foreland basin of western Argentina. Four facies associations have been identified: a basal glacial marine association, a shallow marine association, a deltaic association, and an uppermost fluvial association. Sand-prone deposits in the deltaic association, a shallow marine association, a deltaic association, and an uppermost fluvial association. Sand-prone deposits in the deltaic association are represented by prodelta and delta-front shales and subordinate fine sandstones (Facies A), deltaic platform, wave-reworked channel mouth-bar sandstones (Facies B), and fluvial-dominated distributary channel sandstones (Facies C). Analysis of framework grainsmore » of sandstone samples from Facies B and C shows two distinct mineral assemblages or petrofacies. The quartzose petrofacies is characterized by high contents of quartz and low percentages of feldspar and lithic grains. The quartzolithic petrofacies shows an increase in labile components, in particular lithic fragments, and a concomitant decrease in quartz. The quartzolithic petrofacies shows a source signature. Average detrital modes of sandstones from this petrofacies are similar to those from overlying fluvial sandstones. All wave-reworked, channel mouth-bar sandstones (Facies B) correspond compositionally to the quartzose petrofacies, whereas detrital modes from the distributary-channel sandstones (Facies C) fall into the quartzolithic petrofacies. This correspondence between depositional environment and petrofacies suggests a strong depositional influence on composition (depositional signature). Abrasion (mechanical breakdown) by wave action in shallow marine environments accounts for the quartz-rich nature and paucity of labile grains in the quartzose petrofacies.« less

  14. Marginal bed load transport in a gravel bed stream, Sagehen Creek, California

    USGS Publications Warehouse

    Andrews, E.D.

    1994-01-01

    Marginal bed load transport describes the condition when relatively few bed particles are moving at any time. Bed particles resting in the shallowest bed pockets will move when the dimensionless shear stress т* exceeds a value of about 0.020. As т* increases, the number of bed particles moving increases. Significant motion of bed particles, i.e., when a substantial fraction of the bed particles are moving, occurs when т* exceeds a value of about 0.060. Thus marginal bed load transport occurs over the domain 0.020 < т* < 0.060. Marginal bed load transport rates and associated hydraulic characteristics of Sagehen Creek, a small mountain gravel bed stream, were measured on 55 days at discharges ranging from slightly less than one half of the bank-full discharge to more than 4 times the bank-full discharge. Dimensionless shear stress varied from 0.032 to 0.042, and bed particles as large as the 80th percentile of the bed surface were transported. The relation between reference dimensionless shear stress and relative particle protrusion for Sagehen Creek was determined by varying т*ri to obtain the best fit of the Parker bed load function to the measured transport rates. During the period of record (water years 1954–1991), the mean annual quantity of bed load transported past the Sagehen Creek gage was 24.7 tons. Forty-seven percent of all bed load transported during the 38 years of record occurred in just 6 years. During 10 of the 38 years of record, essentially no bed load was transported. The median diameter of bed load was 26 mm, compared to 58 mm in the surface bed material.

  15. Multiple stages of aqueous alteration along fractures in mudstone and sandstone strata in Gale Crater, Mars

    NASA Astrophysics Data System (ADS)

    Yen, A. S.; Ming, D. W.; Vaniman, D. T.; Gellert, R.; Blake, D. F.; Morris, R. V.; Morrison, S. M.; Bristow, T. F.; Chipera, S. J.; Edgett, K. S.; Treiman, A. H.; Clark, B. C.; Downs, R. T.; Farmer, J. D.; Grotzinger, J. P.; Rampe, E. B.; Schmidt, M. E.; Sutter, B.; Thompson, L. M.; MSL Science Team

    2017-08-01

    The Mars rover Curiosity in Gale crater conducted the first-ever direct chemical and mineralogical comparisons of samples that have clear parent (unaltered) and daughter (altered) relationships. The mineralogy and chemistry of samples within and adjacent to alteration halos in a sandstone formation were established by the Chemistry and Mineralogy (CheMin) X-ray diffraction (XRD) instrument and the Alpha Particle X-ray Spectrometer (APXS), respectively. The Stimson formation sandstones unconformably overlie the Murray mudstone formation and represent the youngest stratigraphic unit explored by Curiosity to date. Aqueous alteration of the parent sandstone resulted in a loss of half of the original crystalline mineral phases and a three-fold increase in X-ray amorphous material. Aqueous fluids extensively leached Mg, Al, Mn, Fe, Ni, Zn and other elements from the parent material, decreased the pyroxene to feldspar ratio by a factor of two, introduced Ca and mixed-cation sulfates, and both passively and actively enriched the silica content. Leaching of Mg, Al, Mn, Fe, Ni and Zn and enrichment of Si and S are also observed in alteration halos in the underlying mudstone. These observations are consistent with infiltration of subsurface fluids, initially acidic and then alkaline, propagating along fractures crosscutting the Stimson sandstone and Murray mudstone. The geochemistry and mineralogy suggest a complicated diagenetic history with multiple stages of aqueous alteration under a variety of environmental conditions (e.g. both low and moderate pH). The formation of these alteration halos post-dates lithification of the sandstones and mudstones and represents one of the youngest hydrogeologic events presently known to have occurred in Gale crater.

  16. Geology of the Cooper Ridge NE Quadrangle, Sweetwater County, Wyoming

    USGS Publications Warehouse

    Roehler, Henry W.

    1979-01-01

    The Cooper Ridge NE 7?-minute quadrangle is 18 miles southeast of Rock Springs, Wyo., on the east flank of the Rock Springs uplift. Upper Cretaceous rocks composing the Rock Springs Formation, Ericson Sandstone, Almond Formation, Lewis Shale, Fox Hills Sandstone, and Lance Formation, Paleocene rocks composing the Fort Union Formation, and Eocene rocks composing the Wasatch Formation are exposed and dip 5?-8? southeast. Outcrops are unfaulted and generally homoclinal, but a minor cross-trending fold, the Jackknife Spring anticline, plunges southeastward and interrupts the northeast strike of beds. Older rocks in the subsurface are faulted and folded, especially near the Brady oil and gas field. Coal beds are present in the Almond, Lance, and Fort Union Formations. Coal resources are estimated to be more than 762 million short tons in 16 beds more than 2.5 feet thick, under less than 3,000 ft of overburden. Nearly 166 million tons are under less than 200 ft of overburden and are recoverable by strip mining. Unknown quantities of oil and gas are present in the Cretaceous Rock Springs, Blair, and Dakota Formations, Jurassic sandstone (Entrada Sandstone of drillers), Jurassic(?) and Triassic(?) Nugget Sandstone, Permian Park City Formation, and Pennsylvanian and Permian Weber Sandstone at the Brady field, part of which is in the southeast corner of the quadrangle, and in the Dakota Sandstone at the Prenalta Corp. Bluewater 33-32 well near the northern edge of the quadrangle. Other minerals include uranium in the Almond Formation and titanium in the Rock Springs Formation.

  17. Upscaling gas permeability in tight-gas sandstones

    NASA Astrophysics Data System (ADS)

    Ghanbarian, B.; Torres-Verdin, C.; Lake, L. W.; Marder, M. P.

    2017-12-01

    Klinkenberg-corrected gas permeability (k) estimation in tight-gas sandstones is essential for gas exploration and production in low-permeability porous rocks. Most models for estimating k are a function of porosity (ϕ), tortuosity (τ), pore shape factor (s) and a characteristic length scale (lc). Estimation of the latter, however, has been the subject of debate in the literature. Here we invoke two different upscaling approaches from statistical physics: (1) the EMA and (2) critical path analysis (CPA) to estimate lc from pore throat-size distribution derived from mercury intrusion capillary pressure (MICP) curve. τ is approximated from: (1) concepts of percolation theory and (2) formation resistivity factor measurements (F = τ/ϕ). We then estimate k of eighteen tight-gas sandstones from lc, τ, and ϕ by assuming two different pore shapes: cylindrical and slit-shaped. Comparison with Klinkenberg-corrected k measurements showed that τ was estimated more accurately from F measurements than from percolation theory. Generally speaking, our results implied that the EMA estimated k within a factor of two of the measurements and more precisely than CPA. We further found that the assumption of cylindrical pores yielded more accurate k estimates when τ was estimated from concepts of percolation theory than the assumption of slit-shaped pores. However, the EMA with slit-shaped pores estimated k more precisely than that with cylindrical pores when τ was estimated from F measurements.

  18. Reservoir heterogeneity in Carter Sandstone, North Blowhorn Creek oil unit and vicinity, Black Warrior Basin, Alabama

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kugler, R.L.; Pashin, J.C.

    1992-05-01

    This report presents accomplishments made in completing Task 3 of this project which involves development of criteria for recognizing reservoir heterogeneity in the Black Warrior basin. The report focuses on characterization of the Upper Mississippian Carter sandstone reservoir in North Blowhorn Creek and adjacent oil units in Lamar County, Alabama. This oil unit has produced more than 60 percent of total oil extracted from the Black Warrior basin of Alabama. The Carter sandstone in North Blowhorn Creek oil unit is typical of the most productive Carter oil reservoirs in the Black Warrior basin of Alabama. The first part of themore » report synthesizes data derived from geophysical well logs and cores from North Blowhorn Creek oil unit to develop a depositional model for the Carter sandstone reservoir. The second part of the report describes the detrital and diagenetic character of Carter sandstone utilizing data from petrographic and scanning electron microscopes and the electron microprobe. The third part synthesizes porosity and pore-throat-size-distribution data determined by high-pressure mercury porosimetry and commercial core analyses with results of the sedimentologic and petrographic studies. The final section of the report discusses reservoir heterogeneity within the context of the five-fold classification of Moore and Kugler (1990).« less

  19. Genesis analysis of high-gamma ray sandstone reservoir and its log evaluation techniques: a case study from the Junggar basin, northwest China.

    PubMed

    Wang, Liang; Mao, Zhiqiang; Sun, Zhongchun; Luo, Xingping; Song, Yong; Liu, Zhen

    2013-01-01

    In the Junggar basin, northwest China, many high gamma-ray (GR) sandstone reservoirs are found and routinely interpreted as mudstone non-reservoirs, with negative implications for the exploration and exploitation of oil and gas. Then, the high GR sandstone reservoirs' recognition principles, genesis, and log evaluation techniques are systematically studied. Studies show that the sandstone reservoirs with apparent shale content greater than 50% and GR value higher than 110API can be regarded as high GR sandstone reservoir. The high GR sandstone reservoir is mainly and directly caused by abnormally high uranium enrichment, but not the tuff, feldspar or clay mineral. Affected by formation's high water sensitivity and poor borehole quality, the conventional logs can not recognize reservoir and evaluate the physical property of reservoirs. Then, the nuclear magnetic resonance (NMR) logs is proposed and proved to be useful in reservoir recognition and physical property evaluation.

  20. Genesis Analysis of High-Gamma Ray Sandstone Reservoir and Its Log Evaluation Techniques: A Case Study from the Junggar Basin, Northwest China

    PubMed Central

    Wang, Liang; Mao, Zhiqiang; Sun, Zhongchun; Luo, Xingping; Song, Yong; Liu, Zhen

    2013-01-01

    In the Junggar basin, northwest China, many high gamma-ray (GR) sandstone reservoirs are found and routinely interpreted as mudstone non-reservoirs, with negative implications for the exploration and exploitation of oil and gas. Then, the high GR sandstone reservoirs' recognition principles, genesis, and log evaluation techniques are systematically studied. Studies show that the sandstone reservoirs with apparent shale content greater than 50% and GR value higher than 110API can be regarded as high GR sandstone reservoir. The high GR sandstone reservoir is mainly and directly caused by abnormally high uranium enrichment, but not the tuff, feldspar or clay mineral. Affected by formation's high water sensitivity and poor borehole quality, the conventional logs can not recognize reservoir and evaluate the physical property of reservoirs. Then, the nuclear magnetic resonance (NMR) logs is proposed and proved to be useful in reservoir recognition and physical property evaluation. PMID:24078797

  1. Tyler sandstones (Pennsylvanian), Dickinson area, North Dakota: a 24-million barrel soil-zone stratigraphic trap

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Land, C.B.

    Approximately 24 million bbl of recoverable oil has been found in stratigraphic traps in the lower Pennsylvanian Tyler formation at the Dickinson, South Heart, and E. Green River Fields, Stark County, North Dakota. Production is from a multiple sequence of quartzose sandstones 5 to 18 ft (1.5 to 5 m) thick deposited as barrier islands along regressive shorelines. A typical vertical sequence is given. Throughout much of the subject area, porosity and permeability in the sandstones have been greatly reduced or completely destroyed by development of caliche paleosols. In the western part, the caliche consists of gray to brown limestonemore » nodules or nodular layers of limestone in the sandstones and contains abundant pyrite. It is estimated that the caliche destroys as much as 50% of the potential reservoir rock in the area and is an essential factor in the stratigraphic entrapment of the petroleum accumulations by providing an eastern (updip) barrier to migration.« less

  2. Preliminary observations on the impact of complex stress histories on sandstone response to salt weathering: laboratory simulations of process combinations

    NASA Astrophysics Data System (ADS)

    McCabe, S.; Smith, B. J.; Warke, P. A.

    2007-03-01

    Historic sandstone structures carry an inheritance, or a ‘memory’, of past stresses that the stone has undergone since its placement in a façade. This inheritance, which conditions present day performance, may be made up of long-term exposure to a combination of low magnitude background environmental factors (for example, salt weathering, temperature and moisture cycling) and, superimposed upon these, less frequent but potentially high magnitude events or ‘exceptional’ factors (for example, lime rendering, severe frost events, fire). The impact of complex histories on the decay pathways of historic sandstone is not clearly understood, but this paper seeks to improve that understanding through the use of a laboratory ‘process combination’ study. Blocks of quartz sandstone (Peakmoor, from NW England) were divided into subsets that experienced different histories (lime rendering and removal, fire and freeze-thaw cycles in isolation and combination) that reflected the event timeline of a real medieval sandstone monument in NE Ireland, Bonamargy Friary (McCabe et al. 2006b). These subsets were then subject to salt weathering cycles using a 10% salt solution of NaCl and MgSO4 that represents the ‘every-day’ stress environment of, for example, sandstone structures in coastal, or polluted urban, location. Block response to salt weathering was monitored by collecting, drying and weighing the debris that was released as blocks were immersed in the salt solution at the beginning of each cycle. The results illustrate the complexity of the stone decay system, showing that seemingly small variations in stress history can produce divergent response to salt weathering cycles. Applied to real-world historic sandstone structures, this concept may help to explain the spatial and temporal variability of sandstone response to background environmental factors on a single façade, and encourage conservators to include the role of stress inheritance when selecting and

  3. Geology and ground-water in western Santa Cruz County, California, with particular emphasis on the Santa Margarita Sandstone

    USGS Publications Warehouse

    Akers, J.P.; Jackson, L.E.

    1977-01-01

    The water-bearing potential of the geologic formations in the western part of Santa Cruz County, Calif., is evaluated. Most of the sedimentary formations in this area are fine-grained rocks of Tertiary age that have been folded and faulted. These rocks, in general, yield supplies of water sufficient only for individual domestic supplies. The Lompico and Santa Margarita Sandstones, however, are coarser grained and have the potential to yield moderate quantities of water (50-100 gallons per minute). Areas where the Lompico Sandstone might warrant explorations are (1) near and on the west side of the Ben Lomond fault, (2) near and south of the outcrop of the Lompico Sandstone between Ben Lomond and Felton, and (3) in the area near Bald Mountain School. The Santa Margarita Sandstone should be explored by test drilling in the area between Davenport and Bonnie Doon. The quality of ground water is generally good, although saline water occurs in the San Lorenzo Formation near Redwood Grove and Riverside Grove. (Woodard-USGS)

  4. Experimental study and theoretical interpretation of saturation effect on ultrasonic velocity in tight sandstones under different pressure conditions

    NASA Astrophysics Data System (ADS)

    Li, Dongqing; Wei, Jianxin; Di, Bangrang; Ding, Pinbo; Huang, Shiqi; Shuai, Da

    2018-03-01

    Understanding the influence of lithology, porosity, permeability, pore structure, fluid content and fluid distribution on the elastic wave properties of porous rocks is of great significance for seismic exploration. However, unlike conventional sandstones, the petrophysical characteristics of tight sandstones are more complex and less understood. To address this problem, we measured ultrasonic velocity in partially saturated tight sandstones under different effective pressures. A new model is proposed, combining the Mavko-Jizba-Gurevich relations and the White model. The proposed model can satisfactorily simulate and explain the saturation dependence and pressure dependence of velocity in tight sandstones. Under low effective pressure, the relationship of P-wave velocity to saturation is pre-dominantly attributed to local (pore scale) fluid flow and inhomogeneous pore-fluid distribution (large scale). At higher effective pressure, local fluid flow gradually decreases, and P-wave velocity gradually shifts from uniform saturation towards patchy saturation. We also find that shear modulus is more sensitive to saturation at low effective pressures. The new model includes wetting ratio, an adjustable parameter that is closely related to the relationship between shear modulus and saturation.

  5. 7 CFR 2902.15 - Bedding, bed linens, and towels.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that... minimum biobased content is 12 percent and shall be based on the amount of qualifying biobased carbon in..., and silk are not qualifying biobased feedstocks for the purpose of determining the biobased content of...

  6. Monitoring CO2 penetration and storage in the brine-saturated low permeable sandstone by the geophysical exploration technologies

    NASA Astrophysics Data System (ADS)

    Honda, H.; Mitani, Y.; Kitamura, K.; Ikemi, H.; Imasato, M.

    2017-12-01

    Carbon dioxide (CO2) capture and storage (CCS) plays a vital role in reducing greenhouse gas emissions. In the northern part of Kyushu region of Japan, complex geological structure (Coalfield) is existed near the CO2 emission source and has 1.06 Gt of CO2 storage capacity. The geological survey shows that these layers are formed by low permeable sandstone. It is necessary to monitor the CO2 behavior and clear the mechanisms of CO2 penetration and storage in the low permeable sandstone. In this study, measurements of complex electrical impedance (Z) and elastic wave velocity (P-wave velocity: Vp) were conducted during the supercritical CO2 injection experiment into the brine-saturated low permeable sandstone. The experiment conditions were as follows; Confining pressure: 20 MPa, Initial pore pressure: 10 MPa, 40 °, CO2 injection rate: 0.01 to 0.5 mL/min. Z was measured in the center of the specimen and Vp were measured at three different heights of the specimen at constant intervals. In addition, we measured the longitudinal and lateral strain at the center of the specimen, the pore pressure and CO2 injection volume (CO2 saturation). During the CO2 injection, the change of Z and Vp were confirmed. In the drainage terms, Vp decreased drastically once CO2 reached the measurement cross section.Vp showed the little change even if the flow rate increased (CO2 saturation increased). On the other hand, before the CO2 front reached, Z decreased with CO2-dissolved brine. After that, Z showed continuously increased as the CO2 saturation increased. From the multi-parameter (Hydraulic and Rock-physics parameters), we revealed the detail CO2 behavior in the specimen. In the brine-saturated low permeable sandstone, the slow penetration of CO2 was observed. However, once CO2 has passed, the penetration of CO2 became easy in even for brine-remainded low permeable sandstone. We conclude low permeable sandstone has not only structural storage capacity but also residual tapping

  7. Evaluation of a clay-based acidic bedding conditioner for dairy cattle bedding.

    PubMed

    Proietto, R L; Hinckley, L S; Fox, L K; Andrew, S M

    2013-02-01

    This study investigated the effects of a clay-based acidic bedding conditioner on sawdust bedding pH, dry matter (DM), environmental pathogen counts, and environmental bacterial counts on teat ends of lactating dairy cows. Sixteen lactating Holstein cows were paired based on parity, days in milk, milk yield, and milk somatic cell count, and were negative for the presence of an intramammary pathogen. Within each pair, cows were randomly assigned to 1 of 2 treatments with 3-wk periods in a crossover design. Treatment groups consisted of 9 freestalls per group bedded with either untreated sawdust or sawdust with a clay-based acidic bedding conditioner, added at 3- to 4-d intervals over each 21-d period. Bedding and teat ends were aseptically sampled on d 0, 1, 2, 7, 14, and 21 for determination of environmental bacterial counts. At the same time points, bedding was sampled for DM and pH determination. The bacteria identified in the bedding material were total gram-negative bacteria, Streptococcus spp., and coliform bacteria. The bacteria identified on the teat ends were Streptococcus spp., coliform bacteria, and Klebsiella spp. Teat end score, milk somatic cell count, and intramammary pathogen presence were measured weekly. Bedding and teat cleanliness, environmental high and low temperatures, and dew point data were collected daily. The bedding conditioner reduced the pH, but not the DM, of the sawdust bedding compared with untreated sawdust. Overall environmental bacterial counts in bedding were lower for treated sawdust. Total bacterial counts in bedding and on teat ends increased with time over both periods. Compared with untreated sawdust, the treated bedding had lower counts of total gram-negative bacteria and streptococci, but not coliform counts. Teat end bacterial counts were lower for cows bedded on treated sawdust for streptococci, coliforms, and Klebsiella spp. compared with cows bedded on untreated sawdust. The clay-based acidic bedding conditioner

  8. Lithology, hydraulic properties, and water quality of the Sandstone Aquifer in the northwestern part of the Bad River Indian Reservation, Wisconsin, 1998-1999

    USGS Publications Warehouse

    Dunning, Charles P.

    2005-01-01

    The Precambrian sandstone aquifer in the northwestern part of the Bad River Band of Lake Superior Tribe of Chippewa Indians Reservation, Ashland County, Wisconsin, provides much of the drinking water to area residents. A study was undertaken in cooperation with the Bad River Tribe to provide specific information about the lithology, hydraulic properties, and water quality of the sandstone aquifer. During 1998 and 1999, the U.S. Geological Survey installed three monitoring wells, collected and analyzed lithologic and water samples, and conducted geophysical logging and aquifer tests to characterize the sandstone aquifer. The two monitoring wells in the southeastern part of the study area, the Diaperville Monitoring Well #1 (Diaperville MW #1) and the Tolman Monitoring Well #1 (Tolman MW #1) , are believed to have encountered older Middle Proterozoic Oronto Group sandstones. The sandstone encountered in the Ackley Monitoring Well #1 (Ackley MW #1) is believed to be Chequamegon Sandstone of the Late Proterozoic Bayfield Group. This interpretation is based on previous studies, as well as thin- section analysis of sandstone core recovered from the Ackley Monitoring Well #1. Results of aquifer tests conducted in the Diaperville Monitoring Well #1 and the Tolman Monitoring Well #1 provide ranges for hydraulic param - eter values in the sandstone aquifer: transmissivity ranges from 83 to 509 square feet per day; hydraulic conductivity ranges from 1.6 to 4.5 feet per day; storativity ranges from 0.00019 to 0.00046; and specific capacity ranges from 0.22 to 0.67 gallons per minute per foot. Though high- and low-angle fractures are present in Ackley Monitoring Well #1 core, the hydraulic properties of the bedrock appear to be due largely to the matrix porosity measured in thin section (16–21 percent) and permeability of the sandstone. The aquifer test for the Diaperville Monitoring Well #1 resulted in observed drawdown in nearby glacial wells, evidence of a hydraulic

  9. PROTON MICROPROBE ANALYSIS OF TRACE-ELEMENT VARIATIONS IN VITRINITES IN THE SAME AND DIFFERENT COAL BEDS.

    USGS Publications Warehouse

    Minkin, J.A.; Chao, E.C.T.; Blank, Herma; Dulong, F.T.

    1987-01-01

    The PIXE (proton-induced X-ray emission) microprobe can be used for nondestructive, in-situ analyses of areas as small as those analyzed by the electron microprobe, and has a sensitivity of detection as much as two orders of magnitude better than the electron microprobe. Preliminary studies demonstrated that PIXE provides a capability for quantitative determination of elemental concentrations in individual coal maceral grains with a detection limit of 1-10 ppm for most elements analyzed. Encouraged by the earlier results, we carried out the analyses reported below to examine trace element variations laterally (over a km range) as well as vertically (cm to m) in the I and J coal beds in the Upper Cretaceous Ferron Sandstone Member of the Mancos Shale in central Utah, and to compare the data with the data from two samples of eastern coals of Pennsylvanian age.

  10. Sedimentary Facies of the West Crocker Formation North Kota Kinabalu-Tuaran Area, Sabah, Malaysia

    NASA Astrophysics Data System (ADS)

    Mohamed, Azfar; Hadi Abd Rahman, Abdul; Suhaili Ismail, Mohd

    2016-02-01

    Newly outcrops exposed in the West Crocker Formation have led to the detail sedimentolgical analysis of the formation. Eight sedimentary facies have been recognised in which it was divided into three main groups: (1) sand-dominated facies (F1-F2), (2) poorly- sorted unit mixed sand and mud-dominated facies (F3), and (3) mud-dominated facies (F4-F5). These are: F1- graded sandstone (massive to planar laminated), F2-ripple-cross laminated, wavy and convolute lamination sandstone, F3-chaotic beds of mixed sandstone and mudstone blocks and clasts, F4-lenticular bedded of sandstone, and F5-shale. The studies of the formation has come out that it was deposited in a sand-rich submarine fan with specific location located at (1) inner fan channel-levee complex; (2) mid-fan channelised lobes, and (3) outer fan.

  11. Lithofacies variation across the Mammoth Cave-Pope Megagroup boundary -- a sequence stratigraphic approach

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McDonald, T.A.; Tabor, E.; Marzolf, J.E.

    1994-04-01

    Regional stratigraphic relations in southern Illinois suggest a major unconformity near the top of the St. Genevieve Limestone. Large exposures below the unconformity within the Anna quarries display a retrogradational parasequence-stacking pattern. Eight to 12 m-thick parasequences comprise thinning-upward marine bioclastic wackestone overlain by oolitic and bioclastic thickening-upward eolian( ) grainstone. An eolian origin for the bioclastic grainstones is supported by large scale cross stratification (0.5 to 2 m-thick sets), reworked character of rounded, coated bioclasts, and preserved duneforms. At the quarries, the unconformity is directly overlain by mudstones and sandstones. Thinning-upward mudstones interbedded with very thin (1 to 3more » cm thick) intraclastic packstone tempestites crop out in a roadcut about 500 m NE of the quarries. Small-scale ripples and absence of trace fossils in lower mudstone units suggest an estuarine or lagoonal, brackish-waver environment. The trace fossil Conostichus and horizontal burrows appear abruptly in the upper, thin mudstone units. Highly bioturbated green and red shales overlying a 1 to 4 m-thick covered interval in a roadcut 610 m farther north are interbedded with tidally deposited, medium- to coarse-grained, bioclastic grainstones. The shale-draped, medium cross-bedded grainstones document ten or more tidal bundles. The cross-bedded grainstone is overlain by wavy- to flaser-bedded very fine-grained sandstone suggestive of sand flat origin. These sandstones are overlain by the Aux Vases Sandstone. Numerous low-angle bounding surfaces within the Aux Vases enclose low-angle, wedge-planar cross-bedding. A single irregular surface coated by a few centimeters of poorly sorted unstratified sandstone defines a ravinement surface near the base of the Aux Vases Sandstone.« less

  12. DEFORMATION AND FRACTURE OF POORLY CONSOLIDATED MEDIA - Borehole Failure Mechanisms in High-Porosity Sandstone

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Bezalel c. Haimson

    2005-06-10

    We investigated failure mechanisms around boreholes and the formation of borehole breakouts in high-porosity sandstone, with particular interest to grain-scale micromechanics of failure leading to the hitherto unrecognized fracture-like borehole breakouts and apparent compaction band formation in poorly consolidated granular materials. We also looked at a variety of drilling-related factors that contribute to the type, size and shape of borehole breakouts. The objective was to assess their effect on the ability to establish correlations between breakout geometry and in situ stress magnitudes, as well as on borehole stability prediction, and hydrocarbon/water extraction in general. We identified two classes of mediummore » to high porosity (12-30%) sandstones, arkosic, consisting of 50-70% quartz and 15 to 50% feldspar, and quartz-rich sandstones, in which quartz grain contents varied from 90 to 100%. In arkose sandstones critical far-field stress magnitudes induced compressive failure around boreholes in the form of V-shaped (dog-eared) breakouts, the result of dilatant intra-and trans-granular microcracking subparallel to both the maximum horizontal far-field stress and to the borehole wall. On the other hand, boreholes in quartz-rich sandstones failed by developing fracture-like breakouts. These are long and very narrow (several grain diameters) tabular failure zones perpendicular to the maximum stress. Evidence provided mainly by SEM observations suggests a failure process initiated by localized grain-bond loosening along the least horizontal far-field stress springline, the packing of these grains into a lower porosity compaction band resembling those discovered in Navajo and Aztec sandstones, and the emptying of the loosened grains by the circulating drilling fluid starting from the borehole wall. Although the immediate several grain layers at the breakout tip often contain some cracked or even crushed grains, the failure mechanism enabled by the formation

  13. Attenuation of Landfill Leachate In Unsaturated Sandstone

    NASA Astrophysics Data System (ADS)

    Butler, A. P.; Brook, C.; Godley, A.; Lewin, K.; Young, C. P.

    Landfill leachate emanating from old "dilute and disperse" sites represents a potential (and in many cases actual) threat to the integrity of groundwater. Indeed, this concern has been included in EU legislation (80/86/EEC), where key contaminants (e.g. ammonia, various toxic organic compounds and heavy metals) are explicitly highlighted in terms of their impact on groundwater. In the UK, whilst there are a substantial number of unlined landfills sited on major aquifers, many of these are in locations where there is a substantial unsaturated zone. Thus, there exists the opportunity for the modification and attenuation of contaminants prior to it encountering the water table. An understanding of likely changes in leachate content and concentrations at such sites will enable a more comprehensive assessment of the potential risks and liabilities posed by such sites to be evaluated. The Burntstump landfill, situated 8 km north of Nottingham (UK), is sited on an outcrop of Sherwood sandstone. The fine friable sand has been quarried since the 1960s and the excavated volume used to store municipal waste. Filling at the site commenced in the mid 1970s and originally was unlined. In 1978 the first of what was to become a series of boreholes was installed within an area of roughly 5 m radius over one of the original waste cells. Cores of the waste and underlying sandstone were extracted and analysed for a range of physical and chemical parameters. The most recent set of analyses were obtained in 2000. The series of investigations therefore provide an important record of leachate migration and modification through the unsaturated zone for over twenty years. The progression of the leachate front is clearly delineated by the chloride concentration profile with an average velocity of around 1.6 m.yr-1. Combining this value with an average (and reasonably uniform) measured moisture content of about 7% gives a mean inter-granular specific discharge of 110 mm.yr-1. An interesting

  14. Decay of sandstone monuments in Petra (Jordan): Gravity-induced stress as a stabilizing factor

    NASA Astrophysics Data System (ADS)

    Řihošek, Jaroslav; Bruthans, Jiří; Mašín, David; Filippi, Michal; Schweigstillova, Jana

    2016-04-01

    As demonstrated by physical experiments and numerical modeling the gravity-induced stress (stress in further text) in sandstone massive reduces weathering and erosion rate (Bruthans et al. 2014). This finding is in contrast to common view that stress threatens stability of man-made monuments carved to sandstone. Certain low- levels of gravity-induced stress can in fact stabilize and protect these forms against weathering and disintegration. The purpose of this investigation is to evaluate the effect of the stress on weathering of sandstone monuments at the Petra World Heritage Site in Jordan via field observations, salt weathering experiments, and physical and numerical modeling. Previous studies on weathering of Petra monuments have neglected the impact of stress, but the ubiquitous presence of stress-controlled landforms in Petra suggests that it has a substantial effect on weathering and erosion processes on man-made monuments and natural surfaces. Laboratory salt weathering experiments with cubes of Umm Ishrin sandstone from Petra demonstrated the inverse relationship between stress magnitude and decay rate. Physical modeling with Strelec locked sand from the Czech Republic was used to simulate weathering and decay of Petra monuments. Sharp forms subjected to water erosion decayed to rounded shapes strikingly similar to tombs in Petra subjected to more than 2000 years of weathering and erosion. The physical modeling results enabled visualization of the recession of monument surfaces in high spatial and temporal resolution and indicate that the recession rate of Petra monuments is far from constant both in space and time. Numerical modeling of stress fields confirms the physical modeling results. This novel approach to investigate weathering clearly demonstrates that increased stress decreases the decay rate of Petra monuments. To properly delineate the endangered zones of monuments, the potential damage caused by weathering agents should be combined with stress

  15. Depositional environment of the downdip Queen City (Eocene) Sandstone, Mestena Grande Field Area, Jim Hogg and Duval Counties, Texas

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    McCormack, J.

    1994-09-01

    The downdip Queen City sandstone interval in the Mestena Grande field area of the south Texas Gulf Coast basin comprises two sandstone depositional units, referred to in this paper as A Lobe and B Lobe. A total of 583 ft (179 m) of conventional core from 11 wells containing predominantly B Lobe deposits were examined macroscopically. The A Lobe is a thin (6-34 ft; 1.8-10.4 m) fine- to very fine-grained, mostly bioturbated, well-sorted sandstone. The B Lobe is composed of fine to very fine, well-sorted sandstone interbedded with siltstone and mudstone. The trace fossil assemblage of the B Lobe indicatesmore » that sediments were deposited in the cruziana ichnofacies. Trace fossils and authigenic minerals also suggest oxygen stratification during deposition. B Lobe contains five subunits, each up to 13.5 ft (4 m) net sand thickness. These units were deposited as part of a highstands systems tract during the early Lutetian Stage (lower middle Eocene). B Lobe is a primarily aggradational unit composed of storm-generated sandstone and heterolithic deposits of the lower shoreface to inner shelf environment. A Lobe is a coarsening upward unit and represents progradation of the shoreface during late highstand systems tract development. An interlobal mudstone, which separates the units, marks the transition from early to late highstand systems tract development.« less

  16. Paediatric burn unit in Portugal: Beds needed using a bed-day approach.

    PubMed

    Santos, João V; Viana, João; Amarante, José; Freitas, Alberto

    2017-03-01

    Despite the high burden of children with burns, there is not a paediatric burn unit (PBU) in Portugal. We aimed to estimate the Portuguese health care providing needs on paediatric burns. We performed a nation-wide retrospective study, between 2009 and 2013, among less than 16 years-old inpatients with burns that met the transfer criteria to a burn unit in Portugal. A bed-day approach was used, targeting an occupancy rate of 70-75%, and possible locations were studied. The primary outcome was the number of beds needed, and secondary outcomes were the overload and revenue for each possible number of beds in a PBU. A total of 1155 children met the transfer criteria to a burn unit, representing a total of 17,371 bed-days. Occupancy rates of 11-bed, 12-bed, 13-bed and 14-bed PBU were, respectively, 79.7%, 75.3%, 71.0% and 66.8%. The 13-bed PBU scenario would represent an overload of 523 bed-days, revenue of more than 5 million Euros and a ratio of 1 PBU bed per 123,409 children. Using a groundbreaking approach, the optimal number of PBU beds needed in Portugal is 13. However, as half of the patients who met burn transfer criteria are not transferred, this bed number might be overestimated if this pattern maintains, despite the underestimation with our method approach. If a PBU is to be created the preferable location is Porto. Cost-effectiveness studies should be performed. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

  17. Initial ecosystem restoration in the highly erodible Kisatchie Sandstone Hills

    Treesearch

    D. Andrew Scott

    2014-01-01

    Restoration of the unique and diverse habitats of the Kisatchie Sandstone Hills requires the re-introduction of fire to reduce fuel accumulation and promote herbaceous vegetation, but some soils in the area are extremely erodible, and past fires have resulted in high erosion rates. Overstory and understory vegetation, downed woody fuels, and other stand attributes were...

  18. Multi-scale nitrate transport in a sandstone aquifer system under intensive agriculture

    NASA Astrophysics Data System (ADS)

    Paradis, Daniel; Ballard, Jean-Marc; Lefebvre, René; Savard, Martine M.

    2018-03-01

    Nitrate transport in heterogeneous bedrock aquifers is influenced by mechanisms that operate at different spatial and temporal scales. To understand these mechanisms in a fractured sandstone aquifer with high porosity, a groundwater-flow and nitrate transport model—reproducing multiple hydraulic and chemical targets—was developed to explain the actual nitrate contamination observed in groundwater and surface water in a study area on Prince Edward Island, Canada. Simulations show that nitrate is leached to the aquifer year-round, with 61% coming from untransformed and transformed organic sources originating from fertilizers and manure. This nitrate reaches the more permeable shallow aquifer through fractures in weathered sandstone that represent only 1% of the total porosity (17%). Some of the nitrate reaches the underlying aquifer, which is less active in terms of groundwater flow, but most of it is drained to the main river. The river-water quality is controlled by the nitrate input from the shallow aquifer. Groundwater in the underlying aquifer, which has long residence times, is also largely influenced by the diffusion of nitrate in the porous sandstone matrix. Consequently, following a change of fertilizer application practices, water quality in domestic wells and the river would change rapidly due to the level of nitrate found in fractures, but a lag time of up to 20 years would be necessary to reach a steady level due to diffusion. This demonstrates the importance of understanding nitrate transport mechanisms when designing effective agricultural and water management plans to improve water quality.

  19. Petrological features of selected components of the Cergowa sandstones (Outer Carpathians) recorded by scanning electron microscopy - preliminary study

    NASA Astrophysics Data System (ADS)

    Pszonka, Joanna

    2017-11-01

    The scanning electron microscope analysis of the Cergowa sandstones brings new data on their petrological features and chemical composition. Previous work in standard petrographic examination, e.g. polarising (PL) or cathodoluminescence (CL) microscopy, displayed limited information on grain surface topography and only assumptions to their geochemistry. Both identification and characterisation of minerals are fundamental in the progress of mining and minerals processing systems. Detrital grains of the Cergowa sandstones are bound by calcite and dolomitic cement and commonly corroded by diagenetic fluids, however, in varying degrees, which is illustrated here by feldspar, quartz and dolomite minerals. Dissolution processes of marginal parts of these mineral grains resulted in corrosion, which increased the contact surface between the grains and the cement. The difference in resistance to these processes was observed not only among distinct groups of minerals, but also within the group of feldspars: between K-feldspars and minerals of plagioclase. That combination resulted in exceptionally strong cementation of the Cergowa sandstones, which is expressed by their high hardness and resistance to abrasion, freezing, and thawing. Inherent parameters of sandstones are characterised by their petrographical properties.

  20. Experimental measurements of the SP response to concentration and temperature gradients in sandstones with application to subsurface geophysical monitoring

    NASA Astrophysics Data System (ADS)

    Leinov, E.; Jackson, M. D.

    2014-09-01

    Exclusion-diffusion potentials arising from temperature gradients are widely neglected in self-potential (SP) surveys, despite the ubiquitous presence of temperature gradients in subsurface settings such as volcanoes and hot springs, geothermal fields, and oil reservoirs during production via water or steam injection. Likewise, with the exception of borehole SP logging, exclusion-diffusion potentials arising from concentration gradients are also neglected or, at best, it is assumed that the diffusion potential dominates. To better interpret these SP sources requires well-constrained measurements of the various coupling terms. We report measurements of thermoelectric and electrochemical exclusion-diffusion potentials across sandstones saturated with NaCl brine and find that electrode effects can dominate the measured voltage. After correcting for these, we find that Hittorf transport numbers are the same within experimental error regardless of whether ion transport occurs in response to temperature or concentration gradients over the range of NaCl concentration investigated that is typical of natural systems. Diffusion potentials dominate only if the pore throat radius is more than approximately 4000 times larger than the diffuse layer thickness. In fine-grained sandstones with small pore throat diameter, this condition is likely to be met only if the saturating brine is of relatively high salinity; thus, in many cases of interest to earth scientists, exclusion-diffusion potentials will comprise significant contributions from both ionic diffusion through, and ionic exclusion from, the pore space of the rock. However, in coarse-grained sandstones, or sandstones saturated with high-salinity brine, exclusion-diffusion potentials can be described using end-member models in which ionic exclusion is neglected. Exclusion-diffusion potentials in sandstones depend upon pore size and salinity in a complex way: they may be positive, negative, or zero depending upon sandstone

  1. CFD-DEM study of effect of bed thickness for bubbling fluidized beds

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tingwen, Li; Gopalakrishnan, Pradeep; Garg, Rahul

    2011-10-01

    The effect of bed thickness in rectangular fluidized beds is investigated through the CFD–DEM simulations of small-scale systems. Numerical results are compared for bubbling fluidized beds of various bed thicknesses with respect to particle packing, bed expansion, bubble behavior, solids velocities, and particle kinetic energy. Good two-dimensional (2D) flow behavior is observed in the bed having a thickness of up to 20 particle diameters. However, a strong three-dimensional (3D) flow behavior is observed in beds with a thickness of 40 particle diameters, indicating the transition from 2D flow to 3D flow within the range of 20–40 particle diameters. Comparison ofmore » velocity profiles near the walls and at the center of the bed shows significant impact of the front and back walls on the flow hydrodynamics of pseudo-2D fluidized beds. Hence, for quantitative comparison with experiments in pseudo-2D columns, the effect of walls has to be accounted for in numerical simulations.« less

  2. Muddy and dolomitic rip-up clasts in Triassic fluvial sandstones: Origin and impact on potential reservoir properties (Argana Basin, Morocco)

    NASA Astrophysics Data System (ADS)

    Henares, Saturnina; Arribas, Jose; Cultrone, Giuseppe; Viseras, Cesar

    2016-06-01

    The significance of rip-up clasts as sandstone framework grains is frequently neglected in the literature being considered as accessory components in bulk sandstone composition. However, this study highlights the great value of muddy and dolomitic rip-up clast occurrence as: (a) information source about low preservation potential from floodplain deposits and (b) key element controlling host sandstone diagenetic evolution and thus ultimate reservoir quality. High-resolution petrographic analysis on Triassic fluvial sandstones from Argana Basin (T6 and T7/T8 units) highlights the significance of different types of rip-up clasts as intrabasinal framework components of continental sediments from arid climates. On the basis of their composition and ductility, three main types are distinguished: (a) muddy rip-up clasts, (b) dolomitic muddy rip-up clasts and (c) dolomite crystalline rip-up clasts. Spatial distribution of different types is strongly facies-related according to grain size. Origin of rip-up clasts is related to erosion of coeval phreatic dolocretes, in different development stages, and associated muddy floodplain sediments. Cloudy cores with abundant inclusions and clear outer rims of dolomite crystals suggest a first replacive and a subsequent displacive growth, respectively. Dolomite crystals are almost stoichiometric. This composition is very similar to that of early sandstone dolomite cement, supporting phreatic dolocretes as dolomite origin in both situations. Sandstone diagenesis is dominated by mechanical compaction and dolomite cementation. A direct correlation exists between: (1) muddy rip-up clast abundance and early reduction of primary porosity by compaction with irreversible loss of intergranular volume (IGV); and (2) occurrence of dolomitic rip-up clasts and dolomite cement nucleation in host sandstone, occluding adjacent pores but preserving IGV. Both processes affect reservoir quality by generation of vertical and 3D fluid flow baffles and

  3. Petrologic and isotopic data from the Cretaceous (Campanian) Blackhawk Formation and Star Point Sandstone (Mesaverde Group), Wasatch Plateau, Utah

    USGS Publications Warehouse

    Fishman, Neil S.; Turner, Christine E.; Peterson, Fred

    2013-01-01

    The presence of discrete minerals associated with coal—whether (1) detrital or authigenic constituents of the coals or in thin mudstone or siltstone units interbedded with coals, or (2) authigenic phases that formed along cleats—might influence its utilization as an energy resource. The build-up of sintered ash deposits on the surfaces of heat exchangers in coal-fired power plants, due to the alteration of minerals during combustion of the coal, can seriously affect the functioning of the boiler and enhance corrosion of combustion equipment. In particular, the presence of sodium in coals has been considered a key factor in the fouling of boilers; however, other elements (such as calcium or magnesium) and the amount of discrete minerals burned with coal can also play a significant role in the inefficiency of and damage to boilers. Previous studies of the quality of coals in the Cretaceous (Campanian) Blackhawk Formation of the Wasatch Plateau, Utah, revealed that the sodium content of the coals varied across the region. To better understand the origin and distribution of sodium in these coals, petrologic studies were undertaken within a sedimentological framework to evaluate the timing and geochemical constraints on the emplacement of sodium-bearing minerals, particularly analcime, which previously had been identified in coals in the Blackhawk Formation. Further, the study was broadened to include not just coals in the Blackhawk Formation from various localities across the Wasatch Plateau, but also sandstones interbedded with the coals as well as sandstones in the underlying Star Point Sandstone. The alteration history of the sandstones in both formations was considered a key component of this study because it records the nature and timing of fluids passing through them and the associated precipitation of sodium-bearing minerals; thus, the alteration history could place constraints on the distribution and timing of sodium mineralization in the interbedded or

  4. Variability of bed drag on cohesive beds under wave action

    USGS Publications Warehouse

    Safak, Ilgar

    2016-01-01

    Drag force at the bed acting on water flow is a major control on water circulation and sediment transport. Bed drag has been thoroughly studied in sandy waters, but less so in muddy coastal waters. The variation of bed drag on a muddy shelf is investigated here using field observations of currents, waves, and sediment concentration collected during moderate wind and wave events. To estimate bottom shear stress and the bed drag coefficient, an indirect empirical method of logarithmic fitting to current velocity profiles (log-law), a bottom boundary layer model for combined wave-current flow, and a direct method that uses turbulent fluctuations of velocity are used. The overestimation by the log-law is significantly reduced by taking turbulence suppression due to sediment-induced stratification into account. The best agreement between the model and the direct estimates is obtained by using a hydraulic roughness of 10 -4">−4 m in the model. Direct estimate of bed drag on the muddy bed is found to have a decreasing trend with increasing current speed, and is estimated to be around 0.0025 in conditions where wave-induced flow is relatively weak. Bed drag shows an increase (up to fourfold) with increasing wave energy. These findings can be used to test the bed drag parameterizations in hydrodynamic and sediment transport models and the skills of these models in predicting flows in muddy environments.

  5. Effective pressure law for permeability of E-bei sandstones

    NASA Astrophysics Data System (ADS)

    Li, M.; Bernabé, Y.; Xiao, W.-I.; Chen, Z.-Y.; Liu, Z.-Q.

    2009-07-01

    Laboratory experiments were conducted to determine the effective pressure law for permeability of tight sandstone rocks from the E-bei gas reservoir, China. The permeability k of five core samples was measured while cycling the confining pressure pc and fluid pressure pf. The permeability data were analyzed using the response-surface method, a statistical model-building approach yielding a representation of k in (pc, pf) space that can be used to determine the effective pressure law, i.e., peff = pc - κpf. The results show that the coefficient κ of the effective pressure law for permeability varies with confining pressure and fluid pressure as well as with the loading or unloading cycles (i.e., hysteresis effect). Moreover, κ took very small values in some of the samples, even possibly lower than the value of porosity, in contradiction with a well-accepted theoretical model. We also reanalyzed a previously published permeability data set on fissured crystalline rocks and found again that the κ varies with pc but did not observe κ values lower than 0.4, a value much larger than porosity. Analysis of the dependence of permeability on effective pressure suggests that the occurrence of low κ values may be linked to the high-pressure sensitivity of E-bei sandstones.

  6. Geology of the Powder River Basin, Wyoming and Montana, with reference to subsurface disposal of radioactive wastes

    USGS Publications Warehouse

    Beikman, Helen M.

    1962-01-01

    The Powder River Basin is a structural and topographic basin occupying an area of about 20,000 square miles in northeastern Wyoming arid southeastern Montana. The Basin is about 230 miles long in a northwest-southeast direction and is about 100 miles wide. It is bounded on three sides by mountains in which rocks of Precambrian age are exposed. The Basin is asymmetrical with a steep west limb adjacent to the Bighorn Mountains and a gentle east limb adjacent to the Black Hills. Sedimentary rocks within the Basin have a maximum thickness of about 18,000 feet and rocks of every geologic period are represented. Paleozoic rocks are about 2,500 feet thick and consist of marine bonate rocks and sandstone; Mesozoic rocks are about 9,500 feet thick and consist of both marine and nonmarine siltstone and sandstone; and Cenozoic rocks are from 4,000 to 6,000 feet thick and consist of coal-bearing sandstone and shale. Radioactive waste could be stored in the pore space of permeable sandstone or in shale where space could be developed. Many such rock units that could be used for storing radioactive wastes are present within the Powder River Basin. Permeable sandstone beds that may be possible reservoirs for storage of radioactive waste are present throughout the Powder River Basin. These include sandstone beds in the Flathead Sandstone and equivalent strata in the Deadwood Formation, the Tensleep Sandstone and equivalent strata in the Minnelusa Formation and the Sundance Formation in rocks of pre-Cretaceous age. However, most of the possible sandstone reservoirs are in rocks of Cretaceous age and include sandstone beds in the Fall River, Lakota, Newcastle, Frontier, Cody, and Mesaverde Formations. Problems of containment of waste such as clogging of pore space and chemical incompatibility would have to be solved before a particular sandstone unit could be selected for waste disposal. Several thick sequences of impermeable shale such as those in the Skull Creek, Mowry, Frontier

  7. Hybrid fluidized bed combuster

    DOEpatents

    Kantesaria, Prabhudas P.; Matthews, Francis T.

    1982-01-01

    A first atmospheric bubbling fluidized bed furnace is combined with a second turbulent, circulating fluidized bed furnace to produce heat efficiently from crushed solid fuel. The bed of the second furnace receives the smaller sizes of crushed solid fuel, unreacted limestone from the first bed, and elutriated solids extracted from the flu gases of the first bed. The two-stage combustion of crushed solid fuel provides a system with an efficiency greater than available with use of a single furnace of a fluidized bed.

  8. Epilithic lichens in the Beacon sandstone formation, Victoria Land, Antarctica

    NASA Technical Reports Server (NTRS)

    Hale, M. E.; Friedmann, E. I. (Principal Investigator)

    1987-01-01

    The epilithic lichen flora on the Beacon sandstone formation in Victoria Land consists of seven species: Acarospora gwynnii Dodge & Rudolph, Buellia grisea Dodge & Baker, B. pallida Dodge & Baker, Carbonea capsulata (Dodge & Baker) Hale comb. nov., Lecanora fuscobrunnea Dodge & Baker, Lecidea cancriformis Dodge & Baker, and L. siplei Dodge & Baker. The typification of the species is given along with descriptions and distribution in Antarctica.

  9. Zeta potential in oil-brine-sandstone system and its role in oil recovery during controlled salinity waterflooding

    NASA Astrophysics Data System (ADS)

    Li, S.; Jackson, M.

    2017-12-01

    Wettability alteration is widely recognised as a primary role in improved oil recovery (IOR) during controlled salinity waterflooding (CSW) by modifying brine composition. The change of wettability of core sample depends on adsorption of polar oil compounds into the mineral surface which influences its surface charge density and zeta potential. It has been proved that zeta potentials can be useful to quantify the wettability and incremental oil recovery in natural carbonates. However, the study of zeta potential in oil-brine-sandstone system has not investigated yet. In this experimental study, the zeta potential is used to examine the controlled salinity effects on IOR in nature sandstone (Doddington) aged with two types of crude oils (Oil T and Oil D) over 4 weeks at 80 °C. Results show that the zeta potential measured in the Oil T-brine-sandstone system following primary waterflooding decreases compared to that in fully water saturation, which is consistent with the negative oil found in carbonates study, and IOR response during secondary waterflooding using diluted seawater was observed. In the case of negative oil, the injected low salinity brine induces a more repulsive electrostatic force between the mineral-brine interface and oil-brine interface, which results in an increase disjoining pressure and alters the rock surface to be more water-wet. For Oil D with a positive oil-brine interface, the zeta potential becomes more positive compared to that under single phase condition. The conventional waterflooding fails to observe the IOR in Oil D-brine-sandstone system due to a less repulsive electrostatic force built up between the two interfaces. After switching the injection brine from low salinity brine to formation brine, the IOR was observed. Measured zeta potentials shed some light on the mechanism of wettability alteration in the oil-brine-sandstone system and oil recovery during CSW.

  10. STRUCTURAL HETEROGENEITIES AND PALEO FLUID FLOW IN AN ANALOG SANDSTONE RESERVOIR 2001-2004

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Pollard, David; Aydin, Atilla

    2005-02-22

    Fractures and faults are brittle structural heterogeneities that can act both as conduits and barriers with respect to fluid flow in rock. This range in the hydraulic effects of fractures and faults greatly complicates the challenges faced by geoscientists working on important problems: from groundwater aquifer and hydrocarbon reservoir management, to subsurface contaminant fate and transport, to underground nuclear waste isolation, to the subsurface sequestration of CO2 produced during fossil-fuel combustion. The research performed under DOE grant DE-FG03-94ER14462 aimed to address these challenges by laying a solid foundation, based on detailed geological mapping, laboratory experiments, and physical process modeling, onmore » which to build our interpretive and predictive capabilities regarding the structure, patterns, and fluid flow properties of fractures and faults in sandstone reservoirs. The material in this final technical report focuses on the period of the investigation from July 1, 2001 to October 31, 2004. The Aztec Sandstone at the Valley of Fire, Nevada, provides an unusually rich natural laboratory in which exposures of joints, shear deformation bands, compaction bands and faults at scales ranging from centimeters to kilometers can be studied in an analog for sandstone aquifers and reservoirs. The suite of structures there has been documented and studied in detail using a combination of low-altitude aerial photography, outcrop-scale mapping and advanced computational analysis. In addition, chemical alteration patterns indicative of multiple paleo fluid flow events have been mapped at outcrop, local and regional scales. The Valley of Fire region has experienced multiple episodes of fluid flow and this is readily evident in the vibrant patterns of chemical alteration from which the Valley of Fire derives its name. We have successfully integrated detailed field and petrographic observation and analysis, process-based mechanical modeling, and

  11. Convolute laminations and load structures in turbidites as indicators of flow reflections and decelerations against bounding slopes. Examples from the Marnoso-arenacea Formation (northern Italy) and Annot Sandstones (south eastern France)

    NASA Astrophysics Data System (ADS)

    Tinterri, R.; Muzzi Magalhaes, P.; Tagliaferri, A.; Cunha, R. S.

    2016-10-01

    This work discusses the significance of particular types of soft-sediment deformations very common within turbidite deposits, namely convolute laminations and load structures. Detailed facies analyses of the foredeep turbidites in the Marnoso-arenacea Formation (northern Italy) and Annot Sandstones (south eastern France) show that these deformational structures tend to increase near morphological obstacles, concomitantly with contained-reflected beds. The lateral and vertical distribution of convolute laminae and load structures, as well as their geometry, has a well-defined depositional logic related to flow decelerations and reflections against bounding slopes. This evidence suggests an interaction between fine-grained sediment and the presence of morphologic relief, and impulsive and cyclic-wave loadings, which are produced by flow impacts or reflected bores and internal waves related to impinging bipartite turbidity currents.

  12. Mid and Late Devonian arenites deposited by sheet-flood, braided streams and rivers in the northern Barrier Ranges, far western New South Wales, Australia

    NASA Astrophysics Data System (ADS)

    Neef, G.; Bottrill, R. S.; Cohen, D. R.

    1996-05-01

    Extensive and well exposed, fine-grained fluvial sandstone and less common pebbly coarse-grained fluvial sandstone of Devonian age, crop out in the northern Barrier Ranges of far west New South Wales, Australia. These strata were deposited largely on low-gradient alluvial fans in a basin and range landscape and contain common sedimentary structures (especially streaming lineations and tabular cross-beds). Around 400 of these sedimentary structures were measured to determine the palaeoflow trends of the sheet floods, streams or rivers which deposited the sandstone. The strata are mapped as the Mid Devonian Coco Range Sandstone and the Late Devonian Nundooka Sandstone, which together are around 2.7 km thick. They were deposited at the western margin of the large Emsian to Early Carboniferous Darling Basin. The Coco Range Sandstone is Emsian to Eifelian in age (based on fragments) of fossil fish) and it is separated from the Frasnian-Famennian (Late Devonian) Nundooka Sandstone by the north-trending Nundooka Creek Fault. The eastern boundary of the Nundooka Sandstone is formed by the Western Boundary Fault. Eastward of this fault is the north-trending and 40 km wide Bancannia Trough, which contains gently folded Late Silurian to Early Carboniferous strata up to 7.5 km thick. Most of the Coco Range Sandstone and all of the Nundooka Sandstone are non-graded, fine and very fine-grained, light brown sub-litharenites which are considered to have been deposited mainly on low-gradient alluvial fans. Sedimentary successions of 1.75 to 5.25 m thickness in the fine-grained arenite usually commence with Sm (massive or slumped) → Sh (laminated arenite) or St (trough cross-beds) → Sp (tabular cross-bedded sandstone). An erosional surface commonly underlies the sedimentary successions and they are interpreted to be the result of deposition from decelerating sheet floods. Units composed of tabular cross-bedded strata several metres thick are rarely channelised and are

  13. Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

    NASA Astrophysics Data System (ADS)

    Ghanbarian, Behzad; Berg, Carl F.

    2017-09-01

    Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

  14. Hospital bed occupancy: more than queuing for a bed.

    PubMed

    Keegan, Andrew D

    2010-09-06

    Timely access to safe hospital care remains a major concern. Target bed-occupancy rates have been proposed as a measure of the ability of a hospital to function safely and effectively. High bed-occupancy rates have been shown to be associated with greater risks of hospital-associated infection and access block and to have a negative impact on staff health. Clinical observational data have suggested that bed occupancies above 85% could adversely affect safe, effective hospital function. Using this figure, at least initially, would be of value in the planning and operational management of public hospital beds in Australia. There is an urgent need to develop meaningful outcome measures of patient care that could replace the process measures currently in use.

  15. Acoustic Emission Parameters of Three Gorges Sandstone during Shear Failure

    NASA Astrophysics Data System (ADS)

    Xu, Jiang; Liu, Yixin; Peng, Shoujian

    2016-12-01

    In this paper, an experimental investigation of sandstone samples from the Three Gorges during shear failure was conducted using acoustic emission (AE) and direct shear tests. The AE count rate, cumulative AE count, AE energy, and amplitude of the sandstone samples were determined. Then, the relationships among the AE signals and shearing behaviors of the samples were analyzed in order to detect micro-crack initiation and propagation and reflect shear failure. The results indicated that both the shear strength and displacement exhibited a logarithmic relationship with the displacement rate at peak levels of stress. In addition, the various characteristics of the AE signals were apparent in various situations. The AE signals corresponded with the shear stress under different displacement rates. As the displacement rate increased, the amount of accumulative damage to each specimen decreased, while the AE energy peaked earlier and more significantly. The cumulative AE count primarily increased during the post-peak period. Furthermore, the AE count rate and amplitude exhibited two peaks during the peak shear stress period due to crack coalescence and rock bridge breakage. These isolated cracks later formed larger fractures and eventually caused ruptures.

  16. An Experimental Study of the Fracture Coalescence Behaviour of Brittle Sandstone Specimens Containing Three Fissures

    NASA Astrophysics Data System (ADS)

    Yang, S. Q.; Yang, D. S.; Jing, H. W.; Li, Y. H.; Wang, S. Y.

    2012-07-01

    To analyse the fracture coalescence behaviour of rock, rectangular prismatic sandstone specimens (80 × 160 × 30 mm in size) containing three fissures were tested under uniaxial compression. The strength and deformation behaviours of the specimens are first analysed by investigating the effects of the ligament angle β2 on the peak strength, peak strain and crack initiation stress of the specimens. To confirm the sequence of crack coalescence, a photographic monitoring technique is used throughout the entire period of deformation. Based on the results, the relationship between the real-time crack coalescence process and the axial stress-strain curve of brittle sandstone specimens is also developed, and this relationship can be used to evaluate the macroscopic deformation characteristics of pre-cracked rock. The equivalent strain evolution fields of the specimen, with α = β1 = 45° and β2 = 90°, are obtained using the digital image correlation technique and show good agreement with the experimental results of pre-cracked brittle sandstone. These experimental results are expected to improve the understanding of fracture mechanisms and be used in rock engineering with intermittent structures, such as deep underground excavated tunnels.

  17. Section of Morgan formation, Pennsylvanian, at Split Mountain in Dinosaur National Monument, Uintah County, Utah

    USGS Publications Warehouse

    McCann, Franklin T.; Raman, Norman D.; Henbest, Lloyd G.

    1946-01-01

    Extension of the oil pool in the Weber sandstone (Pennsylvanian), in the Rangely oil field, Rio Blanco County, Colorado, subsequent to the completion of the filed work on which Preliminary Chart 16 is based, has stimulated special interest in the beds beneath that sandstone as potential oil reservoirs. In compliance with the demand for additional information concerning these beds, a detailed description of the sequence immediately underlying the Weber sandstone at Split Mountain, Utah, is here given. That part of Split Mountain where the section was measured is approximately 35 airline miles northwest of the town of Rangely. The section itself is shown graphically and somewhat generalized in column 8, sheet 2, Preliminary Chart 16. A more detailed graphic section is presented in the accompanying column section.

  18. Fine bed material in pools of natural gravel bed channels

    Treesearch

    Thomas E. Lisle; Sue Hilton

    1999-01-01

    Abstract - Natural gravel bed channels commonly contain a fine mode of sand and fine gravel that fills voids of the bed framework of coarser gravel. If the supply of fine bed material exceeds the storage capacity of framework voids, excess fine material forms surficial patches, which can be voluminous in pools during low flow. Data collected in 34 natural channels in...

  19. Ash bed level control system for a fixed-bed coal gasifier

    DOEpatents

    Fasching, George E.; Rotunda, John R.

    1984-01-01

    An ash level control system is provided which incorporates an ash level meter to automatically control the ash bed level of a coal gasifier at a selected level. The ash level signal from the ash level meter is updated during each cycle that a bed stirrer travels up and down through the extent of the ash bed level. The ash level signal is derived from temperature measurements made by thermocouples carried by the stirrer as it passes through the ash bed and into the fire zone immediately above the ash bed. The level signal is compared with selected threshold level signal to determine if the ash level is above or below the selected level once each stirrer cycle. A first counter is either incremented or decremented accordingly. The registered count of the first counter is preset in a down counter once each cycle and the preset count is counted down at a selected clock rate. A grate drive is activated to rotate a grate assembly supporting the ash bed for a period equal to the count down period to maintain the selected ash bed level. In order to avoid grate binding, the controller provides a short base operating duration time each stirrer cycle. If the ash bed level drops below a selected low level or exceeds a selected high level, means are provided to notify the operator.

  20. Geology and recognition criteria for sandstone uranium deposits in mixed fluvial-shallow marine sedimentary sequences, South Texas. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Adams, S.S.; Smith, R.B.

    1981-01-01

    Uranium deposits in the South Texas Uranium Region are classical roll-type deposits that formed at the margin of tongues of altered sandstone by the encroachment of oxidizing, uraniferous solutions into reduced aquifers containing pyrite and, in a few cases, carbonaceous plant material. Many of the uranium deposits in South Texas are dissimilar from the roll fronts of the Wyoming basins. The host sands for many of the deposits contain essentially no carbonaceous plant material, only abundant disseminated pyrite. Many of the deposits do not occur at the margin of altered (ferric oxide-bearing) sandstone tongues but rather occur entirely within reduced,more » pyurite-bearing sandstone. The abundance of pyrite within the sands probably reflects the introduction of H/sub 2/S up along faults from hydrocarbon accumulations at depth. Such introductions before ore formation prepared the sands for roll-front development, whereas post-ore introductions produced re-reduction of portions of the altered tongue, leaving the deposit suspended in reduced sandstone. Evidence from three deposits suggests that ore formation was not accompanied by the introduction of significant amounts of H/sub 2/S.« less

  1. Thrust-ridge paleodepositional model for the Upper Freeport coal bed and associated clastic facies, Upper Potomac coal field, Appalachian Basin, U.S.A.

    USGS Publications Warehouse

    Belt, Edward S.; Lyons, P.C.

    1990-01-01

    Two differential depositional sequences are recognized within a 37-m-thick lowermost section of the Conemaugh Group of Late Pennsylvanian (Westphalian D) age in the southern part of the Upper Potomac coal field (panhandle of Maryland and adjacent West Virginia). The first sequence is dominated by the Upper Freeport coal bed and zone (UF); the UF consists of a complex of interfingered thick coal beds and mudrocks. The UF underlies the entire 500 km2 study area (approximately 40 km in a NE-SW direction). The second sequence is dominated by medium- to coarse-grained sandstone and pebbly sandstone. They were deposited in channel belts that cut into and interfingered laterally with mudrock and fine- to medium-grained sandstone facies of floodbasin and crevasse-lobe origin. Thin lenticular coals occur in the second sequence. Nowhere in the study area does coarse-grained sandstone similar to the sandstone of the channel belts of the second sequence occur within the UF. However, 20 km north of the study area, coarse channel belts are found that are apparently synchronous with the UF (Lyons et al., 1984). The southeastern margin of the study are is bounded by the Allegheny Front. Between it and the North Mountain thrust (75 km to the southeast), lie at least eight other thrusts of unknown extent (Wilson, 1887). All these thrusts are oriented northwest; Devonian and older strata are exposed at the surface between the Allegheny Front and the North Mountain thrust. A blind-thrust ridge model is proposed to explain the relation of the two markedly depositional sequences to the thrusts that lie to the southeast of the Upper Potomac coal field. This model indicates that thrust ridges diverted coarse clastics from entering the swamp during a period when the thick Upper Freeport peat accumulated. Anticlinal thrust ridges and associated depressions are envisioned to have developed parallel to the Appalachian orogen during Middle and early Late Pennsylvanian time. A blind thrust

  2. Rockfall monitoring of a poorly consolidated marly sandstone cliff by TLS and IR thermography

    NASA Astrophysics Data System (ADS)

    Lefeuvre, Caroline; Guérin, Antoine; Carrea, Dario; Derron, Marc-Henri; Jaboyedoff, Michel

    2017-04-01

    The study area of La Cornalle (Vaud, Switzerland) is a 40 m high south-west facing cliff which is also part of a larger landslide (Bersier 1975 ; Parriaux, 1998). The cliff is formed by an alternation of marls and sandstones. The thicknesses of sandstone layers range from 0.5 to 4 meters. The rockfall activity of this cliff is high, with an average of one event per day. The aim of this study is to better understand the links between rockfall activity, cliff's structures, and weather and thermal conditions. The 3D surface evolution of the Cornalle cliff is monitored approximately every month since September 2012 using a Terrestrial Laser Scanning (TLS) data in order to get a monthly inventory of rockfall events. Since November 2013, a weather station located 150 meters away from the cliff collects data such as temperature, humidity, atmospheric pressure, rain and solar radiation every 15 minutes. Furthermore, we also fixed a thermic probe in the sandstone at 10 cm deep which measures temperature every 10 minutes. A detailed analysis has been performed during a short period (01/29/2016-04/08/2016) and pointed out a correlation between daily rainfall and rockfall. We found that a fall occurred the day or the day after a cumulative daily rainfall of at least 10 mm/day.In parallel to this monthly monitoring, the northwest part of La Cornalle cliff (the most active part) was monitored for 24 consecutive hours in July 2016 (from 12:30 to 12:30) using infrared thermography and crackmeters with a precision of 0.01mm. We collected a series of thermal pictures every 20 minutes, and measured the opening of a crack in sandstone layers every hour. We observed that marls are more affected by external changes of temperature than sandstones. Their surface temperature rises (resp. falls) more with an increase (resp. decrease) of external temperature than sandstones. Crackmeters measured an opening of the crack with an increase of the rock temperature and the opposite displacement

  3. Utilisation of Sand from Kaolin Washing for the Manufacture of Alkali-activated Artificial Sandstone

    NASA Astrophysics Data System (ADS)

    Vavro, Martin; Vavro, Leona; Mec, Pavel; Soucek, Kamil; Pticen, Frantisek; Reiterman, Pavel

    2017-04-01

    Sandstones represent a traditional natural stones which are widely used in Czech architecture and sculpture over a long time. Thanks to their relatively easy workability, sandstones provide a wide range of stone products and also represent a popular material for architectural and sculptural purposes. In the field of restoration of artworks, they are therefore often used for manufacturing stone statue copies originally made from the same or similar type of stone. Despite a relatively common and varied occurrence of natural sandstones, the method of the artificial stone facsimiles creation in the form of various cast elements is also often applied in restoration practice. The history of application of artificial stones in civil engineering and architecture goes back to the ancient times, i.e. to Roman antiquity and possibly up to the time of ancient Egypt. The lack of appropriate natural rock, suitable in the view of colour, grain size or texture is the main reason of manufacturing copies based on synthetic mixtures. The other reason is high financial costs to create a sculpture copy from natural materials. Mixtures made from white and/or grey cements, sands, carefully selected crushed stone or well graded natural gravels, and mineral coloring pigments or mixtures with acrylate, polyester, and epoxy resins binder are the most frequently used artificial materials for cast stone manufacturing. This paper aims to bring information about composition and properties of artificial sandstones made from alkali-activated binder mixtures based on metakaolin and granulated blast furnace slag. The filler of this artificial stone is represented by fine-grained sand generated during kaolin wet processing. Used sand is mainly formed by quartz, feldspars, micas (muscovite > biotite), residual kaolin, and to a lesser extent also by Fe oxyhydroxides ("limonite"), titanium dioxide mineral (probably anatase), and carbonate mineral unidentified in detail. Annual Czech production of this

  4. Lower Cretaceous Avile Sandstone, Neuquen basin, Argentina - Exploration model for a lowstand clastic wedge in a back-arc basin

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ryer, T.A.

    1991-03-01

    The Neuquen basin of western Argentina is a back-arc basin that was occupied by epeiric seas during much of Jurassic and Cretaceous time. The Avile Sandstone Member of the Agrio Formation records a pronounced but short-lived regression of the Agrio sea during middle Hauterivian (Early Cretaceous) time. Abrupt lowering of relative sea level resulted in emergence and erosion of the Agrio sea floor; shoreline and fluvial facies characteristic of the Centenario Formation shifted basinward. The Avile rests erosionally upon lower Agrio shale over a large area; well-sorted, porous sandstones within the member pinch out laterally against the base-Avile erosional surface.more » Avile deposition closed with an abrupt transgression of the shoreline to the approximate position it had occupied prior to the Avile regression. The transgressive deposits are carbonate rich, reflecting starvation of the basin as a consequence of sea-level rise. The Avile lowstand clastic wedge consists predominantly of sandstones deposited in fluvial to shallow-marine paleoenvironments; eolian sandstones probably constitute an important component in the eastern part of the area. The sandstones locally have excellent reservoir characteristics; they constitute the reservoirs in the Puesto Hernandez, Chihuido de la Sierra Negra, and Filo Morado fields. The pinch-out of the Avile lowstand clastic wedge has the potential to form stratigraphic traps in favorable structural positions. The depositional model indicates that there may be a viable stratigraphic play to be made along the Avile pinch-out in the deep, relatively undrilled, northwestern part of the Neuquen basin.« less

  5. An Experimental and Numerical Study on Cracking Behavior of Brittle Sandstone Containing Two Non-coplanar Fissures Under Uniaxial Compression

    NASA Astrophysics Data System (ADS)

    Yang, Sheng-Qi; Tian, Wen-Ling; Huang, Yan-Hua; Ranjith, P. G.; Ju, Yang

    2016-04-01

    To understand the fracture mechanism in all kinds of rock engineering, it is important to investigate the fracture evolution behavior of pre-fissured rock. In this research, we conducted uniaxial compression experiments to evaluate the influence of ligament angle on the strength, deformability, and fracture coalescence behavior of rectangular prismatic specimens (80 × 160 × 30 mm) of brittle sandstone containing two non-coplanar fissures. The experimental results show that the peak strength of sandstone containing two non-coplanar fissures depends on the ligament angle, but the elastic modulus is not closely related to the ligament angle. With the increase of ligament angle, the peak strength decreased at a ligament angle of 60°, before increasing up to our maximum ligament angle of 120°. Crack initiation, propagation, and coalescence were all observed and characterized from the inner and outer tips of pre-existing non-coplanar fissures using photographic monitoring. Based on the results, the sequence of crack evolution in sandstone containing two non-coplanar fissures was analyzed in detail. In order to fully understand the crack evolution mechanism of brittle sandstone, numerical simulations using PFC2D were performed for specimens containing two non-coplanar fissures under uniaxial compression. The results are in good agreement with the experimental results. By analyzing the stress field, the crack evolution mechanism in brittle sandstone containing two non-coplanar fissures under uniaxial compression is revealed. These experimental and numerical results are expected to improve the understanding of the unstable fracture mechanism of fissured rock engineering structures.

  6. Paleohydrologic controls on soft-sediment deformation in the Navajo Sandstone

    NASA Astrophysics Data System (ADS)

    Bryant, Gerald; Cushman, Robert; Nick, Kevin; Miall, Andrew

    2016-10-01

    Many workers have noted the presence of contorted cross-strata in the Navajo Sandstone and other ancient eolianites, and have recognized their significance as indicators of sediment saturation during the accumulation history. Horowitz (1982) proposed a general model for the production of such features in ancient ergs by episodic, seismically induced liquefaction of accumulated sand. A key feature of that popular model is the prevalence of a flat water table, characteristic of a hyper-arid climatic regime, during deformation. Under arid climatic conditions, the water table is established by regional flow and liquefaction is limited to the saturated regions below the level of interdune troughs. However, various paleohydrological indicators from Navajo Sandstone outcrops point toward a broader range of water table configurations during the deformation history of that eolianite. Some outcrops reveal extensive deformation complexes that do not appear to have extended to the contemporary depositional surface. These km-scale zones of deformation, affecting multiple sets of cross-strata, and grading upward into undeformed crossbeds may represent deep water table conditions, coupled with high intensity triggers, which produced exclusively intrastratal deformation. Such occurrences contrast with smaller-scale complexes formed within the zone of interaction between the products of soft-sediment deformation and surface processes of deposition and erosion. The Horowitz model targets the smaller-scale deformation morphologies produced in this near-surface environment. This study examines the implications of a wet climatic regime for the Horowitz deformation model. It demonstrates how a contoured water table, characteristic of humid climates, may have facilitated deformation within active bedforms, as well as in the accumulation. Intra-dune deformation would enable deflation of deformation features during the normal course of dune migration, more parsimoniously accounting for

  7. Large volume submarine ignimbrites in the Shikoku Basin: An example for explosive volcanism in the Western Pacific during the Late Miocene

    NASA Astrophysics Data System (ADS)

    Kutterolf, Steffen; Schindlbeck, Julie C.; Scudder, Rachel P.; Murray, Richard W.; Pickering, Kevin T.; Freundt, Armin; Labanieh, Shasa; Heydolph, Ken; Saito, Sanny; Naruse, Hajime; Underwood, Michael B.; Wu, Huaichun

    2014-05-01

    IODP Expedition 322, an interval of Late Miocene (7.6 to ˜9.1 Ma) tuffaceous and volcaniclastic sandstones was discovered in the Shikoku Basin (Site C0011B), Nankai region. This interval consists of bioturbated silty claystone including four 1-7 m thick interbeds of tuffaceous sandstones (TST) containing 57-82% (by volume) pyroclasts. We use major and trace element glass compositions, as well as radiogenic isotope compositions, to show that the tuffaceous sandstones beds derived from single eruptive events, and that the majority (TST 1, 2, 3a) came from different eruptions from a similar source region, which we have identified to be the Japanese mainland, 350 km away. In particular, diagnostic trace element ratios (e.g., Th/La, Sm/La, Rb/Hf, Th/Nb, and U/Th) and isotopic data indicate a marked contribution from a mantle source beneath continental crust, which is most consistent with a Japanese mainland source and likely excludes the Izu-Bonin island arc and back arc as a source region for the younger TST beds. Nevertheless, some of the chemical data measured on the oldest sandstone bed (TST 3b, Unit IIb) show affinity to or can clearly be attributed to an Izu-Bonin composition. While we cannot completely exclude the possibility that all TST beds derived from unknown and exotic Izu-Bonin source(s), the collected lines of evidence are most consistent with an origin from the paleo-Honshu arc for TST 1 through 3a. We therefore suggest the former collision zone between the Izu-Bonin arc and Honshu paleo-arc as the most likely region where the eruptive products entered the ocean, also concurrent with nearby (˜200 km) possible Miocene source areas for the tuffaceous sandstones at the paleo-NE-Honshu arc. Estimating the distribution area of the tuffaceous sandstones in the Miocene between this source region and the ˜350 km distant Expedition 322, using bathymetric constraints, we calculate that the sandstone beds represent minimum erupted magma volumes between ˜1 and

  8. Description and correlation of reservoir heterogenity within the Big Injun sandstone, Granny Creek field, West Virginia

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Vargo, A.; McDowell, R.; Matchen, D.

    1992-01-01

    The Granny Creek field (approximately 6 sq. miles in area), located in Clay and Roane counties, West Virginia, produces oil from the Big Injun sandstone (Lower Mississippian). Analysis of 15 cores, 22 core analyses, and approximately 400 wireline logs (gamma ray and bulk density) show that the Big Injun (approximately 12 to 55 feet thick) can be separated into an upper, coarse-grained sandstone and a lower, fine-grained sandstone. The Big Injun is truncated by an erosional unconformity of Early to Middle Mississippian age which removes the coarse-grain upper unit in the northwest portion of the field. The cores show nodulesmore » and zones (1 inch to 6 feet thick) of calcite and siderite cement. Where the cements occur as zones, porosity and permeability are reduced. Thin shales (1 inch to 1 foot thick) are found in the coarse-grained member of the Big Injun, whereas the bottom of the fine-grained, lower member contains intertongues of dark shale which cause pinchouts in porosity at the bottom of the reservoir. Calcite and siderite cement are recognized on wireline logs as high bulk density zones that form horizontal, inclined, and irregular pods of impermeable sandstone. At a 400 foot well spacing, pods may be confined to a single well or encompass as many as 30 wells creating linear and irregular barriers to flow. These pods increase the length of the fluid flow path and may divide the reservoir into discrete compartments. The combination of sedimentologic and diagenetic features contribute to the heterogeneity observed in the field.« less

  9. Effects of microstructure on water imbibition in sandstones using X-ray computed tomography and neutron radiography

    NASA Astrophysics Data System (ADS)

    Zhao, Yixin; Xue, Shanbin; Han, Songbai; Chen, Zhongwei; Liu, Shimin; Elsworth, Derek; He, Linfeng; Cai, Jianchao; Liu, Yuntao; Chen, Dongfeng

    2017-07-01

    Capillary imbibition in variably saturated porous media is important in defining displacement processes and transport in the vadose zone and in low-permeability barriers and reservoirs. Nonintrusive imaging in real time offers the potential to examine critical impacts of heterogeneity and surface properties on imbibition dynamics. Neutron radiography is applied as a powerful imaging tool to observe temporal changes in the spatial distribution of water in porous materials. We analyze water imbibition in both homogeneous and heterogeneous low-permeability sandstones. Dynamic observations of the advance of the imbibition front with time are compared with characterizations of microstructure (via high-resolution X-ray computed tomography (CT)), pore size distribution (Mercury Intrusion Porosimetry), and permeability of the contrasting samples. We use an automated method to detect the progress of wetting front with time and link this to square-root-of-time progress. These data are used to estimate the effect of microstructure on water sorptivity from a modified Lucas-Washburn equation. Moreover, a model is established to calculate the maximum capillary diameter by modifying the Hagen-Poiseuille and Young-Laplace equations based on fractal theory. Comparing the calculated maximum capillary diameter with the maximum pore diameter (from high-resolution CT) shows congruence between the two independent methods for the homogeneous silty sandstone but less effectively for the heterogeneous sandstone. Finally, we use these data to link observed response with the physical characteristics of the contrasting media—homogeneous versus heterogeneous—and to demonstrate the sensitivity of sorptivity expressly to tortuosity rather than porosity in low-permeability sandstones.

  10. The effect of organic acids on wettability of sandstone and carbonate rocks

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mwangi, Paulina; Brady, Patrick V.; Radonjic, Mileva

    This paper examines the role of crude oil’s organic acid surface active compounds (SAC) in determining the reservoir wettability over a range of salinities and temperatures. To isolate the effects of individual SACs, this project used model oil mixtures of pure decane and single SACs to represent the oleic phase. Due to the large number of experiments in this study, we used wettability measurement method by the modified flotation technique (MFT) to produce fast, reliable, and quantitative results. The results showed that oil wetting by decane increased with temperature for carbonate rocks. Sandstones oil wetting showed little temperature dependency. Themore » presence of long-chained acids in decane increased oil wetting in sandstone and carbonate rocks as salinity was lowered, while the short-chained acid increased water wetting under the same conditions. The effect of organic acids on wettability was slightly enhanced with increasing temperature for all rock types.« less

  11. The effect of organic acids on wettability of sandstone and carbonate rocks

    DOE PAGES

    Mwangi, Paulina; Brady, Patrick V.; Radonjic, Mileva; ...

    2018-02-21

    This paper examines the role of crude oil’s organic acid surface active compounds (SAC) in determining the reservoir wettability over a range of salinities and temperatures. To isolate the effects of individual SACs, this project used model oil mixtures of pure decane and single SACs to represent the oleic phase. Due to the large number of experiments in this study, we used wettability measurement method by the modified flotation technique (MFT) to produce fast, reliable, and quantitative results. The results showed that oil wetting by decane increased with temperature for carbonate rocks. Sandstones oil wetting showed little temperature dependency. Themore » presence of long-chained acids in decane increased oil wetting in sandstone and carbonate rocks as salinity was lowered, while the short-chained acid increased water wetting under the same conditions. The effect of organic acids on wettability was slightly enhanced with increasing temperature for all rock types.« less

  12. A general power equation for predicting bed load transport rates in gravel bed rivers

    Treesearch

    Jeffrey J. Barry; John M. Buffington; John G. King

    2004-01-01

    A variety of formulae has been developed to predict bed load transport in gravel bed rivers, ranging from simple regressions to complex multiparameter formulations. The ability to test these formulae across numerous field sites has, until recently, been hampered by a paucity of bed load transport data for gravel bed rivers. We use 2104 bed load transport observations...

  13. Changes in the composition and properties of Ashalchinskoye bitumen-saturated sandstones when exposed to water vapor

    NASA Astrophysics Data System (ADS)

    Korolev, E.; Eskin, A.; Kolchugin, A.; Morozov, V.; Khramchenkov, M.; Gabdelvalieva, R.

    2018-05-01

    Ashalchinskoye bitumen deposit is an experimental platform for testing technology of high-viscosity oil extraction from reservoir rocks. Last time for enhanced of oil recovery in reservoir used pressurization a water vapor with a temperature of ∼ 180 ° C (SAGD technology). However, what happens in sandstone reservoir is little known. We did a study of the effects of water vapor on the structural components of bitumen saturated sandstone. In paper were studied the rock samples at base condition and after one week exposure by water vapour. The thermal analysis showed that steaming helps to removes light and middle oil fractions with a boiling point up to 360 ° C from oil saturated sandstones. Content of heavy oil fractions virtually unchanged. Studying the composition of water extractions of samples showed that the process of aquathermolysis of oil is accompanied by a lowering of the pH of the pore solution from 7.4 to 6.5 and rise content in several times of mobile cations Ca2+, Mg2+ and HCO3 -, SO4 2- anions. Follows from this that the thermal steam effect by bitumen saturated sandstones leads to partial oxidation of hydrocarbons with to form a carbon dioxide. The source of sulfate ions were oxidized pyrite aggregates. Due to the increasing acidity of condensed water, which fills the pore space of samples, pore fluid becomes aggressive to calcite and dolomite cement of bitumen saturated sandstones. As a result of the dissolution of carbonate cement the pore fluid enriched by calcium and magnesium cations. Clearly, that the process is accompanied by reduction of contact strength between fragments of minerals and rocks. Resulting part of compounds is separated from the outer side of samples and falls to bottom of water vapor container. Decreasing the amount of calcite and dolomite anions in samples in a steam-treated influence is confirmed by X-Ray analysis. X-Ray analysis data of study adscititious component of rocks showed that when influenced of water vapor to

  14. Modeling CO2 distribution in a heterogeneous sandstone reservoir: the Johansen Formation, northern North Sea

    NASA Astrophysics Data System (ADS)

    Sundal, Anja; Miri, Rohaldin; Petter Nystuen, Johan; Dypvik, Henning; Aagaard, Per

    2013-04-01

    The last few years there has been broad attention towards finding permanent storage options for CO2. The Norwegian continental margin holds great potential for storage in saline aquifers. Common for many of these reservoir candidates, however, is that geological data are sparse relative to thoroughly mapped hydrocarbon reservoirs in the region. Scenario modeling provides a method for estimating reservoir performances for potential CO2 storage sites and for testing injection strategies. This approach is particularly useful in the evaluation of uncertainties related to reservoir properties and geometry. In this study we have tested the effect of geological heterogeneities in the Johansen Formation, which is a laterally extensive sandstone and saline aquifer at burial depths of 2 - 4 km, proposed as a suitable candidate for CO2 storage by Norwegian authorities. The central parts of the Johansen Formation are underlying the operating hydrocarbon field Troll. In order not to interfere with ongoing gas production, a potential CO2 injection well should be located at a safe distance from the gas reservoir, which consequently implies areas presently without well control. From 3D seismic data, prediction of spatial extent of sandstone is possible to a certain degree, whereas intra-reservoir flow baffles such as draping mudstone beds and calcite cemented layers are below seismic resolution. The number and lateral extent of flow baffles, as well as porosity- and permeability distributions are dependent of sedimentary facies and diagenesis. The interpretation of depositional environment and burial history is thus of crucial importance. A suite of scenario models was established for a potential injection area south of the Troll field. The model grids where made in Petrel based on our interpretations of seismic data, wire line logs, core and cuttings samples. Using Eclipse 300 the distribution of CO2 is modeled for different geological settings; with and without the presence of

  15. Paleozoic fluid history of the Michigan Basin: Evidence from dolomite geochemistry in the Middle Ordovician St. Peter Sandstone

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Winter, B.L.; Johnson, C.M.; Simo, J.A.

    1995-04-03

    The isotope (Sr and O) and elemental (Mg, Ca, Mn, Fe, and Sr) compositions of the various dolomites in the Middle Ordovician St. Peter Sandstone in the Michigan Basin are determined and the variations are modeled in terms of fluid-rock interaction or as mixing relations. These geochemical models, combined with the paragenetic sequence of the dolomites and late anhydrite cement, suggest the existence of at least four distinct diagenetic fluids in the St. Peter Sandstone during the paleozoic. Fluid 1 has a composition consistent with a modified older (pre-Middle Ordovician) seawater origin, which indicates that the flow path for thismore » fluid had a major upward component. This fluid resulted in the first and volumetrically most important burial dolomitization event, producing dolomite in both carbonate and quartz sandstone lithofacies in the St. Peter Sandstone. Fluid 2 has a composition consistent with a modified Middle to early Late Ordovician seawater origin, suggesting a major downward component for fluid flow. Fluid 2 produced dolomite cement in the carbonate lithofacies that postdates Fluid 1 dolomite. The composition of Fluid 3 is best interpreted to reflect a heated, deep basinal brine that had previously interacted with the K-feldspar-rich rocks near the Cambrian-Precambrian unconformity in the Michigan Basin, indicating a major upward component for fluid flow. Fluid 3 produced dolomite cement in quartz sandstone lithofacies that postdates Fluid 1 dolomite. Fluid 4 resulted in precipitation of late anhydrite in fractures. The {sup 87}Sr/{sup 86}Sr ratio of the anhydrite is consistent with Fluid 4 originating as a dilute fluid that interacted extensively with Silurian gypsum in the Michigan Basin; this indicates that the flow path of Fluid 4 had a major downward component.« less

  16. Post-depositional alteration of titanomagnetite in a Miocene sandstone, south Texas (U.S.A.)

    USGS Publications Warehouse

    Reynolds, R.L.

    1982-01-01

    Petrographic and geochemical studies have yielded information on the time-space relationships of the post-depositional alteration of detrital titanomagnetite (Ti-mt) in fine- to medium-grained sandstone from unoriented core samples (taken below the water table at depths of 30-45 m) of the Miocene Catahoula Sandstone, south Texas. Aqueous sulfide introduced from sour gas reservoirs along a growth fault into part of the Catahoula shortly after deposition resulted in the replacement at the periphery of Ti-mt grains by iron disulfide (FeS2) minerals. Remnants of Ti-mt in cores of the partly sulfidized grains show no evidence of earlier hematitic oxidation. After sulfidization, part of the sandstone body was invaded by oxygenated groundwaters flowing down a shallowly inclined (1??) hydrologic gradient. The boundary between oxidized and reduced facies is clearly defined by the distribution of ferric and ferrous iron minerals, and the concentrations of Mo, U, and Se. In oxidized (light-red) strata that had not been previously subjected to sulfidic-reducing conditions but that are correlative with strata containing FeS2 minerals, Ti-mt has been partly to entirely replaced pseudomorphously by hematite to form martite. The absence of hematitic alteration of Ti-mt in the reduced facies is strong evidence that martite in the oxidized facies formed after deposition. ?? 1982.

  17. Thermal Analysis of Fluidized Bed and Fixed Bed Latent Heat Thermal Storage System

    NASA Astrophysics Data System (ADS)

    Beemkumar, N.; Karthikeyan, A.; Shiva Keshava Reddy, Kota; Rajesh, Kona; Anderson, A.

    2017-05-01

    Thermal energy storage technology is essential because its stores available energy at low cost. Objective of the work is to store the thermal energy in a most efficient method. This work is deal with thermal analysis of fluidized bed and fixed bed latent heat thermal storage (LHTS) system with different encapsulation materials (aluminium, brass and copper). D-Mannitol has been used as phase change material (PCM). Encapsulation material which is in orbicular shape with 4 inch diameter and 2 mm thickness orbicular shaped product is used. Therminol-66 is used as a heat transfer fluid (HTF). Arrangement of encapsulation material is done in two ways namely fluidized bed and fixed bed thermal storage system. Comparison was made between the performance of fixed bed and fluidized bed with different encapsulation material. It is observed that from the economical point of view aluminium in fluidized bed LHTS System has highest efficiency than copper and brass. The thermal energy storage system can be analyzed with fixed bed by varying mass flow rate of oil paves a way to find effective heat energy transfer.

  18. In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Klein, J.E.

    A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains on internal 'U-tube' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds.IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95% confidence levelmore » were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory.Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM.Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests.« less

  19. In-Bed Accountability Development for a Passively Cooled, Electrically Heated Hydride (PACE) Bed

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    KLEIN, JAMES

    A nominal 1500 STP-L PAssively Cooled, Electrically heated hydride (PACE) Bed has been developed for implementation into a new Savannah River Site tritium project. The 1.2 meter (four-foot) long process vessel contains an internal ''U-tube'' for tritium In-Bed Accountability (IBA) measurements. IBA will be performed on six, 12.6 kg production metal hydride storage beds. IBA tests were done on a prototype bed using electric heaters to simulate the radiolytic decay of tritium. Tests had gas flows from 10 to 100 SLPM through the U-tube or 100 SLPM through the bed's vacuum jacket. IBA inventory measurement errors at the 95 percentmore » confidence level were calculated using the correlation of IBA gas temperature rise, or (hydride) bed temperature rise above ambient temperature, versus simulated tritium inventory. Prototype bed IBA inventory errors at 100 SLPM were the largest for gas flows through the vacuum jacket: 15.2 grams for the bed temperature rise and 11.5 grams for the gas temperature rise. For a 100 SLPM U-tube flow, the inventory error was 2.5 grams using bed temperature rise and 1.6 grams using gas temperature rise. For 50 to 100 SLPM U-tube flows, the IBA gas temperature rise inventory errors were nominally one to two grams that increased above four grams for flows less than 50 SLPM. For 50 to 100 SLPM U-tube flows, the IBA bed temperature rise inventory errors were greater than the gas temperature rise errors, but similar errors were found for both methods at gas flows of 20, 30, and 40 SLPM. Electric heater IBA tests were done for six production hydride beds using a 45 SLPM U-tube gas flow. Of the duplicate runs performed on these beds, five of the six beds produced IBA inventory errors of approximately three grams: consistent with results obtained in the laboratory prototype tests.« less

  20. Making a Bed

    ERIC Educational Resources Information Center

    Wexler, Anthony; Stein, Sherman

    2005-01-01

    The origins of this paper lay in making beds by putting pieces of plywood on a frame: If beds need to be 4 feet 6 inches by 6 feet 3 inches, and plywood comes in 4-foot by 8-foot sheets, how should one cut the plywood to minimize waste (and have stable beds)? The problem is of course generalized.

  1. Mechanism of concave ``tafoni'' and convex ``domal shape'' formation on TRIASSIC red sandstone of some old buildings, Chester City, UK, Case study

    NASA Astrophysics Data System (ADS)

    Kamh, G. M. E.

    2005-08-01

    The weathering factors act on the recent and archaeological sites through different processes based on the dominant environmental conditions. The net result of weathering is deformation of the original form of construction rock. In the current case study, the main aim is to find out the mechanism of formation of two different weathering forms recorded on many old buildings taking Chester City as a case study. The construction rock in the case study is arenitic sandstone with carbonate content ranging from 0.0 to 15.6%. The sandstone blocks are cemented together by hydraulic lime mortar that can easily be altered chemically to salts by acid rain that dominates at the study area. In case of mortar with worse geotechnical limits than the sandstone blocks, the net result is convex “domal” shape blocks, but in case of mortar with better geotechnical limits than the construction sandstone, the net result of weathering is tafoni “concave” weathering form.

  2. SUBSURFACE WELL-LOG CORRELATION OF ARSENIC-BEARING LITHOFACIES IN THE PERMIAN GARBER SANDSTONE AND WELLINGTON FORMATION, CENTRAL OKLAHOMA AQUIFER (COA), CLEVELAND COUNTY, OKLAHOMA

    EPA Science Inventory

    The fluvial Garber Sandstone and the underlying Wellington Formation are important sources of drinking water in central Oklahoma. These formations, which make up much of the COA, consist of amalgamated sandstones with some interbedded mudstones, siltstones, and local mudstone- a...

  3. Sedimentology and reservoir heterogeneity of a valley-fill deposit-A field guide to the Dakota Sandstone of the San Rafael Swell, Utah

    USGS Publications Warehouse

    Kirschbaum, Mark A.; Schenk, Christopher J.

    2010-01-01

    Valley-fill deposits form a significant class of hydrocarbon reservoirs in many basins of the world. Maximizing recovery of fluids from these reservoirs requires an understanding of the scales of fluid-flow heterogeneity present within the valley-fill system. The Upper Cretaceous Dakota Sandstone in the San Rafael Swell, Utah contains well exposed, relatively accessible outcrops that allow a unique view of the external geometry and internal complexity of a set of rocks interpreted to be deposits of an incised valley fill. These units can be traced on outcrop for tens of miles, and individual sandstone bodies are exposed in three dimensions because of modern erosion in side canyons in a semiarid setting and by exhumation of the overlying, easily erodible Mancos Shale. The Dakota consists of two major units: (1) a lower amalgamated sandstone facies dominated by large-scale cross stratification with several individual sandstone bodies ranging in thickness from 8 to 28 feet, ranging in width from 115 to 150 feet, and having lengths as much as 5,000 feet, and (2) an upper facies composed of numerous mud-encased lenticular sandstones, dominated by ripple-scale lamination, in bedsets ranging in thickness from 5 to 12 feet. The lower facies is interpreted to be fluvial, probably of mainly braided stream origin that exhibits multiple incisions amalgamated into a complex sandstone body. The upper facies has lower energy, probably anastomosed channels encased within alluvial and coastal-plain floodplain sediments. The Dakota valley-fill complex has multiple scales of heterogeneity that could affect fluid flow in similar oil and gas subsurface reservoirs. The largest scale heterogeneity is at the formation level, where the valley-fill complex is sealed within overlying and underlying units. Within the valley-fill complex, there are heterogeneities between individual sandstone bodies, and at the smallest scale, internal heterogeneities within the bodies themselves. These

  4. Pore network properties of sandstones in a fault damage zone

    NASA Astrophysics Data System (ADS)

    Bossennec, Claire; Géraud, Yves; Moretti, Isabelle; Mattioni, Luca; Stemmelen, Didier

    2018-05-01

    The understanding of fluid flow in faulted sandstones is based on a wide range of techniques. These depend on the multi-method determination of petrological and structural features, porous network properties and both spatial and temporal variations and interactions of these features. The question of the multi-parameter analysis on fluid flow controlling properties is addressed for an outcrop damage zone in the hanging wall of a normal fault zone on the western border of the Upper Rhine Graben, affecting the Buntsandstein Group (Early Triassic). Diagenetic processes may alter the original pore type and geometry in fractured and faulted sandstones. Therefore, these may control the ultimate porosity and permeability of the damage zone. The classical model of evolution of hydraulic properties with distance from the major fault core is nuanced here. The hydraulic behavior of the rock media is better described by a pluri-scale model including: 1) The grain scale, where the hydraulic properties are controlled by sedimentary features, the distance from the fracture, and the impact of diagenetic processes. These result in the ultimate porous network characteristics observed. 2) A larger scale, where the structural position and characteristics (density, connectivity) of the fracture corridors are strongly correlated with both geo-mechanical and hydraulic properties within the damage zone.

  5. Detrital zircon ages in Korean mid-Paleozoic meta-sandstones (Imjingang Belt and Taean Formation): Constraints on tectonic and depositional setting, source regions and possible affinity with Chinese terranes

    NASA Astrophysics Data System (ADS)

    Han, Seokyoung; de Jong, Koen; Yi, Keewook

    2017-08-01

    Sensitive High-Resolution Ion Microprobe (SHRIMP) U-Th-Pb isotopic data of detrital zircons from mature, quartz-rich meta-sandstones are used to constrain possible tectonic affinities and source regions of the rhythmically layered and graded-bedded series in the Yeoncheon Complex (Imjingang Belt) and the correlative Taean Formation. These metamorphic marine turbidite sequences presently occur along the Paleoproterozoic (1.93-1.83 Ga) Gyeonggi Massif, central Korea's main high-grade metamorphic gneiss terrane. Yet, detrital zircons yielded highly similar multimodal age spectra with peaks that do not match the age repartition in these basement rocks, as late (1.9-1.8 Ga) and earliest (∼ 2.5 Ga) Paleoproterozoic detrital modes are subordinate but, in contrast, Paleozoic (440-425 Ma) and Neoproterozoic (980-920 Ma) spikes are prominent, yet the basement essentially lacks lithologies with such ages. The youngest concordant zircon ages in each sample are: 378, 394 and 423 Ma. The maturity of the meta-sandstones and the general roundness of zircons of magmatic signature, irrespective of their age, suggest that sediments underwent considerable transport from source to sink, and possibly important weathering and recycling, which may have filtered out irradiation-weakened metamorphic zircon grains. In combination with these isotopic data, presence of a low-angle ductile fault contact between the Yeoncheon Complex and the Taean Formation and the underlying mylonitized Precambrian basement implies that they are in tectonic contact and do not have a stratigraphic relationship, as often assumed. Consequently, in all likelihood, both meta-sedimentary formations: (1) are at least of early Late Devonian age, (2) received much of their detritus from distant (reworked) Silurian-Devonian and Early Neoproterozoic magmatic sources, not present in the Gyeonggi Massif, (3) and not from Paleoproterozoic crystalline rocks of this massif, or other Korean Precambrian basement terranes, and

  6. Effectiveness of bed bug monitors for detecting and trapping bed bugs in apartments.

    PubMed

    Wang, Changlu; Tsai, Wan-Tien; Cooper, Richard; White, Jeffrey

    2011-02-01

    Bed bugs, Cimex lectularius L., are now considered a serious urban pest in the United States. Because they are small and difficult to find, there has been strong interest in developing and using monitoring tools to detect bed bugs and evaluate the results of bed bug control efforts. Several bed bug monitoring devices were developed recently, but their effectiveness is unknown. We comparatively evaluated three active monitors that contain attractants: CDC3000, NightWatch, and a home-made dry ice trap. The Climbup Insect Interceptor, a passive monitor (without attractants), was used for estimating the bed bug numbers before and after placing active monitors. The results of the Interceptors also were compared with the results of the active monitors. In occupied apartments, the relative effectiveness of the active monitors was: dry ice trap > CDC3000 > NightWatch. In lightly infested apartments, the Interceptor (operated for 7 d) trapped similar number of bed bugs as the dry ice trap (operated for 1 d) and trapped more bed bugs than CDC3000 and NightWatch (operated for 1 d). The Interceptor was also more effective than visual inspections in detecting the presence of small numbers of bed bugs. CDC3000 and the dry ice trap operated for 1 d were equally as effective as the visual inspections for detecting very low level of infestations, whereas 1-d deployment of NightWatch detected significantly lower number of infestations compared with visual inspections. NightWatch was designed to be able to operate for several consecutive nights. When operated for four nights, NightWatch trapped similar number of bed bugs as the Interceptors operated for 10 d after deployment of NightWatch. We conclude these monitors are effective tools in detecting early bed bug infestations and evaluating the results of bed bug control programs.

  7. The Safety of Hospital Beds

    PubMed Central

    Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

  8. Tanning Bed Perception Survey

    PubMed Central

    Mcquinn, Donna; Lohse, Christine; Hassani, John

    2015-01-01

    Objective: This study was intended to investigate the perception of tanning bed use among college students. Design: A 15-question survey was given to young adults regarding tanning perceptions. Setting: Rochester Community College in Rochester, Minnesota. Participants: Forty-four respondents between 18 and 51 years of age. Measurements: Data was collected via a self-reported questionnaire. Results: In this study, 50 percent of participants were not educated on the risks of melanoma, and 68 percent were not interested in receiving information on melanoma and completing a follow-up survey. More specifically, 63 percent versus 89 percent of participants with no tanning bed versus some tanning bed use did not want information regarding melanoma, respectively. This study also shows that more tanning bed users believe tanning helps prevent burning than non-tanning bed users. Fifty-seven percent of the 35 participants who had never used a tanning bed thought that they never prevent sunburn, while only 11 percent of the nine participants who had used a tanning bed in the past thought that they never prevent sunburn, which was statistically significant. PMID:25852811

  9. EPA-Registered Bed Bug Products

    MedlinePlus

    ... Bugs EPA Registered Bed Bug Products EPA-Registered Bed Bug Products Resources Bed Bug Main Page Top Ten ... Where you can use the pesticide Pesticide type Bed Bug Search Tool Enter the information as described in ...

  10. Fluid bed material transfer method

    DOEpatents

    Pinske, Jr., Edward E.

    1994-01-01

    A fluidized bed apparatus comprising a pair of separated fluid bed enclosures, each enclosing a fluid bed carried on an air distributor plate supplied with fluidizing air from below the plate. At least one equalizing duct extending through sidewalls of both fluid bed enclosures and flexibly engaged therewith to communicate the fluid beds with each other. The equalizing duct being surrounded by insulation which is in turn encased by an outer duct having expansion means and being fixed between the sidewalls of the fluid bed enclosures.

  11. Apparatus for controlling fluidized beds

    DOEpatents

    Rehmat, A.G.; Patel, J.G.

    1987-05-12

    An apparatus and process are disclosed for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance. 2 figs.

  12. Apparatus for controlling fluidized beds

    DOEpatents

    Rehmat, Amirali G.; Patel, Jitendra G.

    1987-05-12

    An apparatus and process for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance.

  13. Characteristics of deltaic deposits in the Cretaceous Pierre Shale, Trinidad Sandstone, and Vermejo Formation, Raton Basin, Colorado.

    USGS Publications Warehouse

    Flores, R.M.; Tur, S.M.

    1982-01-01

    Detailed facies analyses of closely spaced measured surface sections in the Trinidad and adjacent areas of Colorado reflect deposition in the river-influenced delta. That this deltaic system was accompanied by abandonment of subdeltas is indicated by a destructional-deltaic facies of heavily bioturbated, carbonaceous sandstones, siltstones, and shales best recorded in the delta front deposits of the Trinidad Sandstone. Coal accumulation of the Vermejo deposits nevertheless remained primarily controlled by persistent organic sedimentation in interdistributary backswamps. These backswamps, which accumulated thick, lenticular coals, were formed during the normal constructional phase of the delta plain. -from Authors

  14. Collaborative Strategy on Bed Bugs

    EPA Pesticide Factsheets

    The Collaborative Strategy on Bed Bugs was developed by the Federal Bed Bug Workgroup to clarify the federal role in bed bug control and highlight ways that government, community, academia and private industry can work together on bed bug issues.

  15. Introduction to Bed Bugs

    EPA Pesticide Factsheets

    The common bed bug (Cimex lectularius) is a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. EPA and other agencies all consider bed bugs a public health pest, but bed bugs are not known to transmit disease.

  16. Origin of northern Gondwana Cambrian sandstone revealed by detrital zircon SHRIMP dating

    USGS Publications Warehouse

    Avigad, D.; Kolodner, K.; McWilliams, M.; Persing, H.; Weissbrod, T.

    2003-01-01

    Voluminous Paleozoic sandstone sequences were deposited in northern Africa and Arabia following an extended Neoproterozoic orogenic cycle that culminated in the assembly of Gondwana. We measured sensitive high-resolution ion microprobe (SHRIMP) U-Pb ages of detrital zircons separated from several Cambrian units in the Elat area of southern Israel in order to unravel their provenance. This sandstone forms the base of the widespread siliciclastic section now exposed on the periphery of the Arabian-Nubian shield in northeastern Africa and Arabia. Most of the detrital zircons we analyzed yielded Neoproterozoic concordant ages with a marked concentration at 0.55–0.65 Ga. The most likely provenance of the Neoproterozoic detritus is the Arabian-Nubian shield; 0.55–0.65 Ga was a time of posttectonic igneous activity, rift-related volcanism, and strike-slip faulting there. Of the zircons, 30% yielded pre-Neoproterozoic ages grouped at 0.9–1.1 Ga (Kibaran), 1.65–1.85 Ga, and 2.45–2.7 Ga. The majority of the pre-Neoproterozoic zircons underwent Pb loss, possibly as a consequence of the Pan-African orogeny resetting their provenance. Rocks of the Saharan metacraton and the southern Afif terrane in Saudi Arabia (∼1000 km south of Elat) are plausible sources of these zircons. Kibaran basement rocks are currently exposed more than 3000 km south of Elat (flanking the Mozambique belt), but the shape of the detrital zircons of that age and the presence of feldspar in the host sandstone are not fully consistent with such a long-distance transport. Reworking of Neoproteorozoic glacial detritus may explain the presence of Kibaran detrital zircons in the Cambrian of Elat, but the possibility that the Arabian-Nubian shield contains Kibaran rocks (hitherto not recognized) should also be explored.

  17. Time-series analysis on bed morphology affected by debris flows along a headwater steep channel in Ohya-kuzure landslide, central Japan

    NASA Astrophysics Data System (ADS)

    Hayakawa, Y. S.; Imaizumi, F.; Hotta, N.; Tsunetaka, H.

    2013-12-01

    Deformation of steep terrain has been occurring since the formation of Ohyakuzure landslide in 1707. Although erosion controls in recent decades have resulted in vegetation recovery in downstream portions of the landslide terrain, hillslope erosion and debris flows frequently occur in uppermost steep subwatersheds in the landslide area to yield vast amount of sediment downstream. Ichino-sawa subwatershed in the landslide terrain, where detailed monitoring of debris flows and related topographic changes have previously been performed, has particularly steep slopes, and geomorphic processes therein have been quite active. Freeze-thaw weathering of fractured bedrock on hillslopes made of shale and sandstone frequently occurs in winter to spring season, and resultant sediment particles are provided into channel beds, which act as a source of debris flows that frequently occurs in summer season with heavy or accumulated rainfalls. High-resolution assessment of erosion/deposition patterns in channel bed of the Ichinosawa catchment was performed using multi-temporal terrestrial laser scanning data covering 3 seasons for 2 years. Seasonal changes in spatial distribution of erosion and deposition in the channel bed is quantified using a 0.1-m DEM converted from the original point cloud by TLS. The multi-temporal datasets provides an estimate of annual sediment storage and yield on the order of 1,000 - 5,000 m3. Analysis of changes in elevation by transverse and longitudinal profiles shows contrasting patterns of erosion and deposition along the studied reach: in particular, changes in bed elevation is found to be less in a 50-m long reach, whose downstream part seems bounded by valley narrowing and a knickpoint. Several topographic metrics, including stream gradient, surface roughness and topographic openness, were examined to estimate the characteristics of differing transport processes induced by debris flows along the reaches.

  18. Reservoir heterogeneity in Carboniferous sandstone of the Black Warrior basin. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Kugler, R.L.; Pashin, J.C.; Carroll, R.E.

    1994-04-01

    Although oil production in the Black Warrior basin of Alabama is declining, additional oil may be produced through improved recovery strategies, such as waterflooding, chemical injection, strategic well placement, and infill drilling. High-quality characterization of reservoirs in the Black Warrior basin is necessary to utilize advanced technology to recover additional oil and to avoid premature abandonment of fields. This report documents controls on the distribution and producibility of oil from heterogeneous Carboniferous reservoirs in the Black Warrior basin of Alabama. The first part of the report summarizes the structural and depositional evolution of the Black Warrior basin and establishes themore » geochemical characteristics of hydrocarbon source rocks and oil in the basin. This second part characterizes facies heterogeneity and petrologic and petrophysical properties of Carter and Millerella sandstone reservoirs. This is followed by a summary of oil production in the Black Warrior basin and an evaluation of seven improved-recovery projects in Alabama. In the final part, controls on the producibility of oil from sandstone reservoirs are discussed in terms of a scale-dependent heterogeneity classification.« less

  19. Effect of bed characters on the direct synthesis of dimethyldichlorosilane in fluidized bed reactor.

    PubMed

    Zhang, Pan; Duan, Ji H; Chen, Guang H; Wang, Wei W

    2015-03-06

    This paper presents the numerical investigation of the effects of the general bed characteristics such as superficial gas velocities, bed temperature, bed heights and particle size, on the direct synthesis in a 3D fluidized bed reactor. A 3D model for the gas flow, heat transfer, and mass transfer was coupled to the direct synthesis reaction mechanism verified in the literature. The model was verified by comparing the simulated reaction rate and dimethyldichlorosilane (M2) selectivity with the experimental data in the open literature and real production data. Computed results indicate that superficial gas velocities, bed temperature, bed heights, and particle size have vital effect on the reaction rates and/or M2 selectivity.

  20. Effect of Bed Characters on the Direct Synthesis of Dimethyldichlorosilane in Fluidized Bed Reactor

    PubMed Central

    Zhang, Pan; Duan, Ji H.; Chen, Guang H.; Wang, Wei W.

    2015-01-01

    This paper presents the numerical investigation of the effects of the general bed characteristics such as superficial gas velocities, bed temperature, bed heights and particle size, on the direct synthesis in a 3D fluidized bed reactor. A 3D model for the gas flow, heat transfer, and mass transfer was coupled to the direct synthesis reaction mechanism verified in the literature. The model was verified by comparing the simulated reaction rate and dimethyldichlorosilane (M2) selectivity with the experimental data in the open literature and real production data. Computed results indicate that superficial gas velocities, bed temperature, bed heights, and particle size have vital effect on the reaction rates and/or M2 selectivity. PMID:25742729

  1. Valley-fill sequences and onlap geometries, Lower Cretaceous Muddy Sandstone, Kitty Field, Powder River basin, Wyoming

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gardner, M.H.; Gustason, E.R.

    1987-05-01

    The Muddy Sandstone at Kitty field is a valley-fill sequence that records a late Albian sea level rise and accompanying transgression. The valley was cut during a preceding sea level lowstand. Stratal geometries and facies successions within the valley fill demonstrate the history of transgression was not gradual and progressive. Rather, the valley fill comprises a series of discrete, time-bounded, depositional units which onlap the erosional surface. Five time-bounded depositional units were defined by facies successions and were used to define onlap geometries. Facies successions within individual units record progressive shoaling. Capping each succession, there may be a planar disconformity,more » a thin bioturbated interval, or the deepest water facies of the next depositional event. Thus, the termination of each depositional event is marked by an episode of rapid deepening. At a single geographic location, stratal successions within older depositional units represent more landward facies than those within younger units. Therefore, the onlap geometry of the valley-fill sequence consists of a landward-stepping arrangement of depositional units. The primary reservoirs within the valley-fill sequence, at Kitty field, are laterally coalesced, channel-belt sandstones at the base and barrier island sandstones at the top. Reservoir sandstones of lesser quality occur within the intermediate estuarine facies. The stacking pattern, developed by onlap of the units, results in multiple pay zones within mid-valley reaches. The boundaries of each depositional unit define a high-resolution, chronostratigraphic correlation of valley-fill strata, a correlation corroborated by bentonites. This correlation method gives an accurate description of the internal geometry of valley-fill strata and, therefore, provides a basis for understanding the process of transgressive onlap.« less

  2. [Comparison of PAHs distribution in stabilized sludge by sludge drying bed and reed bed].

    PubMed

    Cui, Yu-Bo; Sun, Hong-Jie; Ran, Chun-Qiu; Li, Jin-Feng; Xie, Yao

    2013-03-01

    The difference in the removal efficiencies of polycyclic aromatic hydrocarbons (PAHs) in planted and unplanted sludge drying bed was investigated. Pilot-scale sludge drying bed and reed bed had the same size of 3.0 m x 1.0 m x 1.3 m (L x W x H), and the bed height consisted of a 65 cm media layer and a 65 cm super height. Both beds had a ventilation pipe which was mounted on the drainage pipes. The experiment lasted for three years, and the first two years was the sludge loading period, and the third year was the natural stabilization period. In the first two years, a total thickness of 8.4 m of sludge was loaded and the average sludge loading rate was 41.3 kg x (m2 x a)(-1). After the three-year stabilization, the contents of the sixteen PAHs decreased with time in both the sludge drying bed and the reed bed. The total PAHs contents in the surface, middle and bottom sludge layers in the sludge drying bed were 4.161, 3.543 and 3.118 mg x kg(-1) (DW), corresponding to 26.91%, 37.77% and 45.23% of removal; and the values in the reed bed were 2.722, 1.648 and 1.218 mg x kg(-1) (DW), corresponding to 52.18%, 71.05% and 78.60% of removal. The average PAHs removal in the reed bed was 29.86% higher than that in the sludge drying bed. In the stabilized sludge, the removal of low-molecular-weight PAHs predominated. The results suggested that reed played a positive role in the removal of PAHs.

  3. Fluidized bed combustor modeling

    NASA Technical Reports Server (NTRS)

    Horio, M.; Rengarajan, P.; Krishnan, R.; Wen, C. Y.

    1977-01-01

    A general mathematical model for the prediction of performance of a fluidized bed coal combustor (FBC) is developed. The basic elements of the model consist of: (1) hydrodynamics of gas and solids in the combustor; (2) description of gas and solids contacting pattern; (3) kinetics of combustion; and (4) absorption of SO2 by limestone in the bed. The model is capable of calculating the combustion efficiency, axial bed temperature profile, carbon hold-up in the bed, oxygen and SO2 concentrations in the bubble and emulsion phases, sulfur retention efficiency and particulate carry over by elutriation. The effects of bed geometry, excess air, location of heat transfer coils in the bed, calcium to sulfur ratio in the feeds, etc. are examined. The calculated results are compared with experimental data. Agreement between the calculated results and the observed data are satisfactory in most cases. Recommendations to enhance the accuracy of prediction of the model are suggested.

  4. Pore Structure Model for Predicting Elastic Wavespeeds in Fluid-Saturated Sandstones

    NASA Astrophysics Data System (ADS)

    Zimmerman, R. W.; David, E. C.

    2011-12-01

    During hydrostatic compression, in the elastic regime, ultrasonic P and S wave velocities measured on rock cores generally increase with pressure, and reach asymptotic values at high pressures. The pressure dependence of seismic velocities is generally thought to be due to the closure of compliant cracks, in which case the high-pressure velocities must reflect only the influence of the non-closable, equant "pores". Assuming that pores can be represented by spheroids, we can relate the elastic properties to the pore structure using an effective medium theory. Moreover, the closure pressure of a thin crack-like pore is directly proportional to its aspect ratio. Hence, our first aim is to use the pressure dependence of seismic velocities to invert the aspect ratio distribution. We use a simple analytical algorithm developed by Zimmerman (Compressibility of Sandstones, 1991), which can be used for any effective medium theory. Previous works have used overly restrictive assumptions, such as assuming that the stiff pores are spherical, or that the interactions between pores can be neglected. Here, we assume that the rock contains an exponential distribution of crack aspect ratios, and one family of stiff pores having an aspect ratio lying somewhere between 0.01 and 1. We develop our model in two versions, using the Differential Scheme, and the Mori-Tanaka scheme. The inversion is done using data obtained in dry experiments, since pore fluids have a strong effect on velocities and tend to mask the effect of the pore geometry. This avoids complicated joint inversion of dry and wet data, such as done by Cheng and Toksoz (JGR, 1979). Our results show that for many sets of data on sandstones, we can fit very well the dry velocities. Our second aim is to predict the saturated velocities from our pore structure model, noting that at a given differential stress, the pore structure should be the same as for a dry test. Our results show that the Biot-Gassmann predictions always

  5. Method and apparatus for a combination moving bed thermal treatment reactor and moving bed filter

    DOEpatents

    Badger, Phillip C.; Dunn, Jr., Kenneth J.

    2015-09-01

    A moving bed gasification/thermal treatment reactor includes a geometry in which moving bed reactor particles serve as both a moving bed filter and a heat carrier to provide thermal energy for thermal treatment reactions, such that the moving bed filter and the heat carrier are one and the same to remove solid particulates or droplets generated by thermal treatment processes or injected into the moving bed filter from other sources.

  6. Mineral resources of the Devil's Garden Lava Bed, Squaw Ridge Lava Bed, and Four Craters Lava Bed Wilderness Study Areas, Lake County, Oregon

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Keith, W.J.; King, H.D.; Gettings, M.E.

    1988-01-01

    The Devel's Garden lava Bed, Squaw Ridge Lava Bed, and Four Craters Lava Bed Wilderness Study Areas include approximately 70,940 acres and are underlain entirely by Pleistocene or Holocene lava flows and associated sediments. There is no evidence of hydrothermal alteration in the study areas. No resources were identified in the study areas, but there is low potential for perlite resources in the southern part of the Devil's Garden Lava Bed and the northern half of the Squaw Ridge Lava Bed areas. All three study areas have low potential for geothermal resources and for oil and gas resources.

  7. WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hansen, E. K.

    2015-05-06

    This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

  8. Coniacian sandstones from the North Sudetic Synclinorium revisited: palaeoenvironmental and palaeogeographical reconstructions based on trace fossil analysis and associated body fossils

    NASA Astrophysics Data System (ADS)

    Chrząstek, Alina; Wypych, Monika

    2018-03-01

    The Coniacian quartz sandstones (Żerkowice Member, Rakowice Wielkie Formation) that crop out at quarries near Czaple-Nowa Wieś Grodziska (North Sudetic Synclinorium) contain a low-diversity assemblage of trace fossils: Gyrochorte isp., Ophiomorpha nodosa (Lundgren, 1891), Ophiomorpha isp., Phycodes cf. curvipalmatum (Pollard, 1981), ?Phycodes isp., Planolites cf. beverleyensis (Billings, 1862), Thalassinoides paradoxicus (Woodward, 1830) and ?Thalassinoides isp. Moreover, interesting compound burrow systems, here referred to as Thalassinoides-Phycodes cf. palmatus and ?Thalassinoides-Phycodes, were recognised at the Czaple Quarry. Additionally, ?Gyrochorte isp., Phycodes cf. flabellum (Miller and Dyer, 1878) and ?Treptichnus isp. were encountered at correlative levels in the Rakowice Małe Quarry. Some of these ichnotaxa have not been recorded previously from Coniacian sandstones of the Żerkowice Member. Additionally, in slabs of these sandstones, the gastropod Nerinea bicincta (Bronn, 1836) and the bivalve Lima haidingeri (Zittel, 1866) were found. These interesting finds, in particular the gastropods, were already noted from the study area in the first half of the twentieth century by (Scupin (1912-1913)). Ethologically, the trace fossil assemblage is represented by domichnia or domichnia/fodinichnia (Ophiomorpha, Thalassinoides), fodinichnia (Phycodes) and pascichnia (Gyrochorte, Planolites). The compound burrow systems (Thalassinoides-Phycodes) are interpreted as dwelling/feeding structures. The possible tracemakers are crustaceans (Ophiomorpha, Thalassinoides) or worm-like animals (annelids and other) (Planolites, ?Phycodes, Gyrochorte and ?Treptichnus). The assemblage of trace fossils is characteristic of the Skolithos ichnofacies and Cruziana ichnofacies, typical of shallow-marine settings. Ichnological studies, as well as the presence of accompanying fossils (bivalves, gastropods), confirm the palaeoenvironmental reconstruction of the Żerkowice Member

  9. Fluidized bed calciner apparatus

    DOEpatents

    Owen, Thomas J.; Klem, Jr., Michael J.; Cash, Robert J.

    1988-01-01

    An apparatus for remotely calcining a slurry or solution feed stream of toxic or hazardous material, such as ammonium diurante slurry or uranyl nitrate solution, is disclosed. The calcining apparatus includes a vertical substantially cylindrical inner shell disposed in a vertical substantially cylindrical outer shell, in which inner shell is disposed a fluidized bed comprising the feed stream material to be calcined and spherical beads to aid in heat transfer. Extending through the outer and inner shells is a feed nozzle for delivering feed material or a cleaning chemical to the beads. Disposed in and extending across the lower portion of the inner shell and upstream of the fluidized bed is a support member for supporting the fluidized bed, the support member having uniform slots for directing uniform gas flow to the fluidized bed from a fluidizing gas orifice disposed upstream of the support member. Disposed in the lower portion of the inner shell are a plurality of internal electric resistance heaters for heating the fluidized bed. Disposed circumferentially about the outside length of the inner shell are a plurality of external heaters for heating the inner shell thereby heating the fluidized bed. Further, connected to the internal and external heaters is a means for maintaining the fluidized bed temperature to within plus or minus approximately 25.degree. C. of a predetermined bed temperature. Disposed about the external heaters is the outer shell for providing radiative heat reflection back to the inner shell.

  10. Characterization of the Oriskany and Berea Sandstones: Evaluating Biogeochemical Reactions of Potential Sandstone–Hydraulic Fracturing Fluid Interaction

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Verba, Circe; Harris, Aubrey

    The Marcellus shale, located in the mid-Atlantic Appalachian Basin, has been identified as a source for natural gas and targeted for hydraulic fracturing recovery methods. Hydraulic fracturing is a technique used by the oil and gas industry to access petroleum reserves in geologic formations that cannot be accessed with conventional drilling techniques (Capo et al., 2014). This unconventional technique fractures rock formations that have low permeability by pumping pressurized hydraulic fracturing fluids into the subsurface. Although the major components of hydraulic fracturing fluid are water and sand, chemicals, such as recalcitrant biocides and polyacrylamide, are also used (Frac Focus, 2015).more » There is domestic concern that the chemicals could reach groundwater or surface water during transport, storage, or the fracturing process (Chapman et al., 2012). In the event of a surface spill, understanding the natural attenuation of the chemicals in hydraulic fracturing fluid, as well as the physical and chemical properties of the aquifers surrounding the spill site, will help mitigate potential dangers to drinking water. However, reports on the degradation pathways of these chemicals are limited in existing literature. The Appalachian Basin Marcellus shale and its surrounding sandstones host diverse mineralogical suites. During the hydraulic fracturing process, the hydraulic fracturing fluids come into contact with variable mineral compositions. The reactions between the fracturing fluid chemicals and the minerals are very diverse. This report: 1) describes common minerals (e.g. quartz, clay, pyrite, and carbonates) present in the Marcellus shale, as well as the Oriskany and Berea sandstones, which are located stratigraphically below and above the Marcellus shale; 2) summarizes the existing literature of the degradation pathways for common hydraulic fracturing fluid chemicals [polyacrylamide, ethylene glycol, poly(diallyldimethylammonium chloride

  11. Novel microclimate monitoring and microbial colonisation in sandstones of historic buildings, Glasgow, Scotland

    NASA Astrophysics Data System (ADS)

    Duthie, L.; Hyslop, E.; Lee, M.; Phoenix, V.; Kennedy, C.

    2009-04-01

    The impact of our changing climate on the historic built environment of Scotland has received surprisingly little attention. Current projections indicate that Scotland will become notably wetter and warmer over the coming decades. Winter temperatures are predicted to increase by 30C with 15% more precipitation, one result should be more aggressive microbial weathering of the sandstone buildings. In order to understand better and to quantify the damage potentially caused, it is necessary to analyse existing microbial populations but also to characterize conditions within building stones, how they change over diurnal and seasonal cycles, and how they differ from external conditions. In this study, temperature, humidity and moisture sensors were inserted at different depths into representative Scottish sandstones to record parameters key to microbial colonisation and organic weathering. Penetration of photosynthetically active radiation has also been measured. The within-stone data were compared to meteorological conditions recorded by an adjacent weather station. These data have then been compared with analysis of the microbial populations at different depths within the stone, using osmium stained polished blocks. Notably, microbes occur up to 7 mm beneath the outer sandstone surface, with community structure differing with depth. Clearly, different communities experience very different conditions within the stone, reflecting trophic structure, light penetration and microclimate. The sensor data confirm that temperature and water availability all vary within the stone and differ considerably with the external environment. We conclude that the warm and humid microclimate within Scottish building stones promotes microbial colonisation and stone decay and both will increase significantly with the changing climate of Scotland and north-west Europe.

  12. Bacillus cereus in free-stall bedding.

    PubMed

    Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

    2007-12-01

    To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the

  13. Astronomical cycle origin of bedded chert: A middle Triassic bedded chert sequence, Inuyama, Japan

    NASA Astrophysics Data System (ADS)

    Ikeda, Masayuki; Tada, Ryuji; Sakuma, Hironobu

    2010-09-01

    Astronomical forcing is one of the main drivers of climate change, and astronomical cyclicity recorded in sediments provides a clue to understand the dynamics of the global climate system. Bedded cherts consist of rhythmic alternations of chert and shale beds. Although previous studies have hypothesized that the origin of bedded chert is related to astronomical cycles (e.g. Fischer, 1976; Hori et al., 1993), conclusive proof remains elusive. To explore this possibility, we established a continuous, high-resolution lithostratigraphy of middle Triassic bedded chert in Central Japan. The average duration of each chert-shale couplet is 20 kyr, similar to that of the precession cycle. Spectral analysis of a bed number series of thickness variations in chert beds was performed assuming that each chert-shale couplet represents a 20-kyr precession cycle. The results reveal cycles involving approximately 200, 20, 5, and 2-3 beds, corresponding to periodicities of approximately 4000, 400, 100, and 40-60 kyr, respectively. By further assuming that the 20-bed cycle represents a 405-kyr eccentricity cycle of constant and stable periodicity, we converted the bed number series to a time series. Spectral analysis of the time series revealed distinct periodicities of 3600, 117, 97, and 38 kyr, in addition to 405 kyr. Besides 3600 kyr, these periodicities agree well with the 120, 95, and 37 kyr periodicities for eccentricity cycles and the obliquity cycle during the Triassic. Moreover, we detected amplitude modulation of the approximately 100-kyr cycle of thickness variations in chert beds with a 405-kyr periodicity, which may correspond to amplitude modulation of 100-kyr climatic precession cycle with the 405-kyr periodicity. The approximately 3600-kyr periodicity described above and 1800-kyr periodicity manifested as the amplitude modulation of the 405-kyr cycle are correlated to present-day long-term eccentricity cycles of 2400 and 4800 kyr evolved by chaotic behavior of solar

  14. How many hospital beds?

    PubMed

    Green, Linda V

    For many years, average bed occupancy level has been the primary measure that has guided hospital bed capacity decisions at both policy and managerial levels. Even now, the common wisdom that there is an excess of beds nationally has been based on a federal target of 85% occupancy that was developed about 25 years ago. This paper examines data from New York state and uses queueing analysis to estimate bed unavailability in intensive care units (ICUs) and obstetrics units. Using various patient delay standards, units that appear to have insufficient capacity are identified. The results indicate that as many as 40% of all obstetrics units and 90% of ICUs have insufficient capacity to provide an appropriate bed when needed. This contrasts sharply with what would be deduced using standard average occupancy targets. Furthermore, given the model's assumptions, these estimates are likely to be conservative. These findings illustrate that if service quality is deemed important, hospitals need to plan capacity based on standards that reflect the ability to place patients in appropriate beds in a timely fashion rather than on target occupancy levels. Doing so will require the collection and analysis of operational data-such as demands for and use of beds, and patient delays--which generally are not available.

  15. Rapid ignition of fluidized bed boiler

    DOEpatents

    Osborn, Liman D.

    1976-12-14

    A fluidized bed boiler is started up by directing into the static bed of inert and carbonaceous granules a downwardly angled burner so that the hot gases cause spouting. Air is introduced into the bed at a rate insufficient to fluidize the entire bed. Three regions are now formed in the bed, a region of lowest gas resistance, a fluidized region and a static region with a mobile region at the interface of the fluidized and static regions. Particles are transferred by the spouting action to form a conical heap with the carbonaceous granules concentrated at the top. The hot burner gases ignite the carbonaceous matter on the top of the bed which becomes distributed in the bed by the spouting action and bed movement. Thereafter the rate of air introduction is increased to fluidize the entire bed, the spouter/burner is shut off, and the entire fluidized bed is ignited.

  16. Assessment of undiscovered sandstone-hosted uranium resources in the Texas Coastal Plain, 2015

    USGS Publications Warehouse

    Mihalasky, Mark J.; Hall, Susan M.; Hammarstrom, Jane M.; Tureck, Kathleen R.; Hannon, Mark T.; Breit, George N.; Zielinski, Robert A.; Elliott, Brent

    2015-12-02

    The U.S. Geological Survey estimated a mean of 220 million pounds of recoverable uranium oxide (U3O8 ) remaining as potential undiscovered resources in southern Texas. This estimate used a geology-based assessment method for Tertiary sandstone-hosted uranium deposits in the Texas Coastal Plain sedimentary strata (fig.1).

  17. Bed rest and immunity

    NASA Astrophysics Data System (ADS)

    Sonnenfeld, Gerald; Aviles, Hernan; Butel, Janet S.; Shearer, William T.; Niesel, David; Pandya, Utpal; Allen, Christopher; Ochs, Hans D.; Blancher, Antoine; Abbal, Michel

    2007-02-01

    Space flight has been shown to result in altered immune responses. The current study was designed to investigate this possibility by using the bed rest model of some space flight conditions. A large number of women are included as subjects in the study. The hypothesis being tested is: 60 days head-down tilt bed rest of humans will affect the immune system and resistance to infection. Blood, urine and saliva samples will be obtained from bed rest subjects prior to, at intervals during, and after completion of 60 days of head-down tilt bed rest. Leukocyte blastogenesis, cytokine production and virus reactivation will be assessed. The ability of the subjects to respond appropriately to immunization with the neoantigen bacteriophage φX-174 will also be determined. Bed rest is being carried out at MEDES, Toulouse France, and the University of Texas Medical Branch, Galveston, TX. The studies to be carried out in France will also allow assessment of the effects of muscle/bone exercise and nutritional countermeasures on the immune system in addition to the effects of bed rest.

  18. Particulate fuel bed tests

    NASA Astrophysics Data System (ADS)

    Horn, F. L.; Powell, J. R.; Savino, J. M.

    Gas-cooled reactors using packed beds of small-diameter, coated fuel particles have been proposed for compact, high-power systems. To test the thermal-hydraulic performance of the particulate reactor fuel under simulated reactor conditions, a bed of 800-micrometer diameter particles was heated by its electrical resistance current and cooled by flowing helium gas. The specific resistance of the bed composed of pyrocarbon-coated particles was measured at several temperatures, and found to be 0.09 ohm-cm at 1273 K and 0.06 ohm-cm at 1600 K. The maximum bed power density reached was 1500 W/cu cm at 1500 K. The pressure drop followed the packed-bed correlation, typically 100,000 Pa/cm. The various frit materials used to contain the bed were also tested to 2000 K in helium and hydrogen to determine their properties and reactions with the fuel. Rhenium metal, zirconium carbide, and zirconium oxide appeared to be the best candidate materials, while tungsten and tungsten-rhenium lost mass and strength.

  19. Unconformity-related oil entrapment in Muddy Sandstone: comparison of Kitty and Amos Draw fields, Powder River basin, Wyoming

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Odland, S.K.; Gardner, M.H.; Gustason, E.R.

    1986-08-01

    It has long been known that an unconformity plays a critical role in trapping oil in the Muddy Sandstone in the Powder River basin, but opinions have varied as to exactly where in the section that unconformity is located. Their work indicates that there are, in fact, two unconformities associated with the Muddy in the northern part of the basin. The older of these occurs on top of the Skull Creek Shale, whereas the younger is largely intraformational. In places, the younger unconformity has truncated the older one. It is the younger unconformity that is responsible for creating favorable settingsmore » for stratigraphic entrapment of oil. Two types of unconformity-related oil traps result from fluvial downcutting into and through the strand-plain sandstones of the oldest member of the Muddy during a major sea level drop. In cases where the unconformity cuts through the Muddy into the underlying Skull Creek Shale, permeable valley-fill sediments, deposited during the Muddy transgression, are juxtaposed against the impermeable Skull Creek Shale along the valley walls. Where valleys are oriented roughly perpendicular to regional structure, as at Kitty field, the updip portion of the valley wall can form a permeability barrier to the fluvial reservoir sandstones of the adjacent valley fill. In cases where the unconformity is intraformational, such as at Amos Draw field, early diagenetic clay, associated with the weathered horizon directly beneath the unconformity, can create a seal on top of the strand-plain sandstones of the oldest member of the Muddy.« less

  20. Application of CaO-Based Bed Material for Dual Fluidized Bed Steam Biomass Gasification

    NASA Astrophysics Data System (ADS)

    Koppatz, S.; Pfeifer, C.; Kreuzeder, A.; Soukup, G.; Hofbauer, H.

    Gasification of biomass is a suitable option for decentralized energy supply based on renewable sources in the range of up to 50 MW fuel input. The paper presents the dual fluidized bed (DFB) steam gasification process, which is applied to generate high quality and nitrogen-free product gas. Essential part of the DFB process is the bed material used in the fluidized reactors, which has significant impact on the product gas quality. By the use of catalytically active bed materials the performance of the overall process is increased, since the bed material favors reactions of the steam gasification. In particular, tar reforming reactions are favored. Within the paper, the pilot plant based on the DFB process with 100kW fuel input at Vienna University of Technology, Austria is presented. Actual investigations with focus on CaO-based bed materials (limestone) as well as with natural olivine as bed material were carried out at the pilot plant. The application of CaO-based bed material shows mainly decreased tar content in the product gas in contrast to experiments with olivine as bed material. The paper presents the results of steam gasification experiments with limestone and olivine, whereby the product gas composition as well as the tar content and the tar composition are outlined.

  1. Origin of karst conduits in calcareous sandstone and carbonate-silicate rocks: Complex role of insoluble material

    NASA Astrophysics Data System (ADS)

    Bruthans, Jiri; Balak, Frantisek; Schweigstillova, Jana; Vojtisek, Jan

    2017-04-01

    Carbonate karst is best developed in high-grade limestones and majority of the studies is focused on these rocks. Features developed by dissolution of calcite cement in quartz sandstones and dissolution of various carbonate-silicate rocks are studied far less frequently. Unlike in common karst, the insoluble residuum has to be washed out after dissolution to create high-permeability conduits in these rocks. Aquifers in a Bohemian Cretaceous Basin (BCB), the most important hydrogeological basin in the Czech Republic, consist mainly of quartz and calcareous sandstones to siltstones. These rocks are intercalated by thin layers of calcite-cemented sandstone and low-grade limestone, the latter sometimes partly impregnated by a secondary silica. Results of tracer tests show a high flow velocity in some of the aquifers. Springs with flow rate up to 500 l/s and wells with yield up to 200 l/s occur in these rocks. Dissolution features in BCB were however not yet studied in detail. For identification and characterization of rocks prone to karstification, 350 cores were sampled mostly from boreholes but also from rock outcrops in several areas of BCB. Cores were taken from intervals where: (i) high carbonate content was expected, (ii) conduits and enlarged porosity was observed in rock outcrops or wells, (iii) inflows to boreholes were determined by well logging. Calcium carbonate content was determined by calcimetry in all cores. All cores were leached in hydrochloric acid to observe the degree of disintegration after removal of calcite, which was far dominating portion of total carbonate. Polished sections were prepared from selected cores and Ca, Si, Na, K, Al content was automatically mapped by microprobe to visualize the calcium, silica, feldspar and clay mineral distribution in cores. Conduits were photo documented in the field. Two types of sediments with distinct disintegration characteristics were observed: (i) In sandstone composed of quartz grains cemented by

  2. Water supply of the Dakota sandstone in the Ellendale-Jamestown area, North Dakota, with reference to changes between 1923 and 1938

    USGS Publications Warehouse

    Wenzel, Leland Keith; Sand, H.H.

    1942-01-01

    visited and advice was given the owner regarding the flow to which his well should be reduced. Many of the wells were visited again between 1928 and 1935 in order to check on whether the flow had been sufficiently reduced. Through this program much artesian water was conserved and much valuable information was obtained on the discharge from the basin. It is estimated that between 1920 and 1923 the artesian head in the western part of the Ellendale-Jamestown area declined at an annual rate of about 4 feet, whereas in 1938 the rate of decline was only about 0.5 foot a year. Between 1915 and 1923 the part of the area of artesian flow in the Edgeley quadrangle was reduced an average of 16.5 square miles a year as a result of the eastward movement of the western boundary of the area. Between 1923 and 1938, however, the average rate of shrinkage of this part of the area of artesian flow was only about 4.5 square miles a year. The perennial recharge to each row of townships in the area of artesian flow has been estimated to be about 500 gallons a minute. In 1923 the flow from wells in T. 129 N., Rs. 50 to 65 W., was about 1,000 gallons a minute, or twice the estimated recharge. In 1938 the flow from wells in this row of townships was about 520 gallons a minute, or only slightly more than the estimated recharge. Thus it appears that a balance is being approached between the withdrawal of water from the basin and the perennial recharge to it.It is believed that the water withdrawn from the basin in excess of the perennial recharge has been obtained from storage by the compression of .the sandstone and associated beds of shale due to the increased load placed upon them by the decline in artesian pressure. Calculations made on this theory indicate that the coefficient of storage is about 0.001 that is, about 0.001 cubic foot of water is released from each column of sandstone and shale 1 foot square for each foot of decline in artesian head. Additional computations show that the

  3. Capillary trapping quantification in sandstones using NMR relaxometry

    NASA Astrophysics Data System (ADS)

    Connolly, Paul R. J.; Vogt, Sarah J.; Iglauer, Stefan; May, Eric F.; Johns, Michael L.

    2017-09-01

    Capillary trapping of a non-wetting phase arising from two-phase immiscible flow in sedimentary rocks is critical to many geoscience scenarios, including oil and gas recovery, aquifer recharge and, with increasing interest, carbon sequestration. Here we demonstrate the successful use of low field 1H Nuclear Magnetic Resonance [NMR] to quantify capillary trapping; specifically we use transverse relaxation time [T2] time measurements to measure both residual water [wetting phase] content and the surface-to-volume ratio distribution (which is proportional to pore size] of the void space occupied by this residual water. Critically we systematically confirm this relationship between T2 and pore size by quantifying inter-pore magnetic field gradients due to magnetic susceptibility contrast, and demonstrate that our measurements at all water saturations are unaffected. Diffusion in such field gradients can potentially severely distort the T2-pore size relationship, rendering it unusable. Measurements are performed for nitrogen injection into a range of water-saturated sandstone plugs at reservoir conditions. Consistent with a water-wet system, water was preferentially displaced from larger pores while relatively little change was observed in the water occupying smaller pore spaces. The impact of cyclic wetting/non-wetting fluid injection was explored and indicated that such a regime increased non-wetting trapping efficiency by the sequential occupation of the most available larger pores by nitrogen. Finally the replacement of nitrogen by CO2 was considered; this revealed that dissolution of paramagnetic minerals from the sandstone caused by its exposure to carbonic acid reduced the in situ bulk fluid T2 relaxation time on a timescale comparable to our core flooding experiments. The implications of this for the T2-pore size relationship are discussed.

  4. Recent Advances in Study of the Detrital Mineralogy of Sand and Sandstone: Implications for Teaching.

    ERIC Educational Resources Information Center

    Suttner, Lee J.

    1989-01-01

    Discussed are methods which can be used to stimulate creative thinking in geology students by focusing on what is not known about sandstone petrology. The impact of recent advances on graduate geology teaching are highlighted. (CW)

  5. Reservoir uncertainty, Precambrian topography, and carbon sequestration in the Mt. Simon Sandstone, Illinois Basin

    USGS Publications Warehouse

    Leetaru, H.E.; McBride, J.H.

    2009-01-01

    Sequestration sites are evaluated by studying the local geological structure and confirming the presence of both a reservoir facies and an impermeable seal not breached by significant faulting. The Cambrian Mt. Simon Sandstone is a blanket sandstone that underlies large parts of Midwest United States and is this region's most significant carbon sequestration reservoir. An assessment of the geological structure of any Mt. Simon sequestration site must also include knowledge of the paleotopography prior to deposition. Understanding Precambrian paleotopography is critical in estimating reservoir thickness and quality. Regional outcrop and borehole mapping of the Mt. Simon in conjunction with mapping seismic reflection data can facilitate the prediction of basement highs. Any potential site must, at the minimum, have seismic reflection data, calibrated with drill-hole information, to evaluate the presence of Precambrian topography and alleviate some of the uncertainty surrounding the thickness or possible absence of the Mt. Simon at a particular sequestration site. The Mt. Simon is thought to commonly overlie Precambrian basement granitic or rhyolitic rocks. In places, at least about 549 m (1800 ft) of topographic relief on the top of the basement surface prior to Mt. Simon deposition was observed. The Mt. Simon reservoir sandstone is thin or not present where basement is topographically high, whereas the low areas can have thick Mt. Simon. The paleotopography on the basement and its correlation to Mt. Simon thickness have been observed at both outcrops and in the subsurface from the states of Illinois, Ohio, Wisconsin, and Missouri. ?? 2009. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

  6. A GIS-based model of potential groundwater yield zonation for a sandstone aquifer in the Juye Coalfield, Shangdong, China

    NASA Astrophysics Data System (ADS)

    Yin, Huiyong; Shi, Yongli; Niu, Huigong; Xie, Daolei; Wei, Jiuchuan; Lefticariu, Liliana; Xu, Shuanxiang

    2018-02-01

    Resolving the potential groundwater yield zonation of sandstone aquifers occurring at depths of several hundred meters has been an important and challenging objective of the hydrogeological research focused on preventing flood hazards in coal mines. Using accessible geological exploration data we put forward a method of predicting the spatial distribution of groundwater storage potential in sandstone aquifers from Permian-age coal deposits in Juye Coalfield, Shangdong, China. A Geological, Tectonic and Lithological Composition Index (GTLCI) model was created using the following parameters: sandstone depth and thickness, faults length density (FaLD), faults density (FaD), fault frequency density (FaFD), fault scale density (FaSD), variation coefficient of the slope (VCS) of the coal seam, intensity index of folds in horizontal direction (IIFoH), and lithological composition index (LCI). Each of these factors was subsequently divided into 5 classes. The analytic hierarchy process (AHP) and trapezoidal fuzzy number (TFN) method was applied to calculate the weight of the conditioning factor and their respective sub-classes. Groundwater yield potential contour map, which was initially constructed using the GTLCI values revealed four groundwater abundance zones. The map was further refined by taking into account hydrogeologic data collected during mining activities. The GTLCI model predictive success rate of 80% was explained by the limited number of boreholes available for validation. It is considered that the GTLCI model is effective at predicting zonation of groundwater yield in the sandstone aquifers from Permian- age coal deposits in Juye Coalfield, China.

  7. Channel widening due to urbanization and a major flood can alter bed particle organization and bed stability in an urban boulder-bed channel

    NASA Astrophysics Data System (ADS)

    Prestegaard, K. L.; Behrns, K.; Blanchet, Z.; Hankin, E.

    2007-12-01

    The Anacostia River is a tributary of the Potomac River north of Washington D.C. that has become progressively more urbanized in the past 50 years. Bankfull discharge and bankfull width in the Anacostia have increased by 3- 4x in the past 50 years. Nearby watersheds of similar size and geology, but without significant urbanization, contain threshold gravel-bed streams. The Anacostia, however, is not a threshold channel; it exhibits break-up of boulder-bed channels in upstream reaches and significant gravel bar formation in downstream reaches. These gravel bars have grown and migrated considerably in the past 10-15 years, contributing significantly to local channel widening that can be twice that of adjacent reaches. The purpose of this study is to determine bedload transport rates and grain size distributions and their relationship to discharge, bed organization and sediment supply. Bed mobility data come from both bedload transport measurements and measurements of channel bed changes. Channel bed changes were obtained from a) repeated channel cross section surveys, b) surface and subsurface size distributions, and c) bed particle organization measurements (measurements of location of particles within reaches). These measurements were made prior to and after the floods of 2006, which equalled the largest floods on record for most parts of the Anacostia River. In some boulder bed reaches, boulders were removed from the center of the channel and deposited along and on the channel banks. The mid-channel boulders were replaced by sheets of gravel and cobbles, significantly altering the bed mobility of the channels.

  8. Evidence for Methyl-Compound-Activated Life in Coal Bed System 2 km Below Sea Floor

    NASA Astrophysics Data System (ADS)

    Trembath-reichert, E.; Morono, Y.; Dawson, K.; Wanger, G.; Bowles, M.; Heuer, V.; Hinrichs, K. U.; Inagaki, F.; Orphan, V. J.

    2014-12-01

    IODP Expedition 337 set the record for deepest marine scientific drilling down to 2.4 kmbsf. This cruise also had the unique opportunity to retrieve deep cores from the Shimokita coal bed system in Japan with the aseptic and anaerobic conditions necessary to look for deep life. Onboard scientists prepared nearly 1,700 microbiology samples shared among five different countries to study life in the deep biosphere. Samples spanned over 1 km in sampling depths and include representatives of shale, sandstone, and coal lithologies. Findings from previous IODP and deep mine expeditions suggest the genetic potential for methylotrophy in the deep subsurface, but it has yet to be observed in incubations. A subset of Expedition 337 anoxic incubations were prepared with a range of 13C-methyl substrates (methane, methylamine, and methanol) and maintained near in situ temperatures. To observe 13C methyl compound metabolism over time, we monitored the δ13C of the dissolved inorganic carbon (by-product of methyl compound metabolism) over a period of 1.5 years. Elemental analysis (EA), ion chromatograph (IC), 13C volatile fatty acid (VFA), and mineral-associated microscopy data were also collected to constrain initial and endpoint conditions in these incubations. Our geochemical evidence suggests that the coal horizon incubated with 13C-methane showed the highest activity of all methyl incubations. This provides the first known observation of methane-activated metabolism in the deep biosphere, and suggests there are not only active cells in the deeply buried terrigenous coal bed at Shimokita, but the presence of a microbial community activated by methylotrophic compounds.

  9. Geochemistry of surface and subsurface waters in quartz-sandstones: significance for the geomorphic evolution of tepui table mountains (Gran Sabana, Venezuela)

    NASA Astrophysics Data System (ADS)

    Mecchia, Marco; Sauro, Francesco; Piccini, Leonardo; De Waele, Jo; Sanna, Laura; Tisato, Nicola; Lira, Jesus; Vergara, Freddy

    2014-04-01

    In situ measurements of discharge, pH, electric conductivity (EC), temperature, and SiO2 content have been carried out during five expeditions in the last 20 years on the summit plateaus, inside caves and along the rivers of the surrounding lowlands of three tepui massifs in Venezuela (Auyan, Roraima, and Chimanta). Additionally, detailed chemical analyses were performed on waters sampled in a newly discovered extensive quartz-sandstone cave system on the Auyan Tepui. Rock samples of the quartz-sandstone bedrock from different locations have been analysed to obtain their chemical composition with a wavelength dispersive X-ray fluorescence spectrometer. These data show that the majority of silica present in surface and subsurface water comes from dissolution of quartz and only in minor amount from hydrolysis of other silicate minerals. Probably the presence of a hardened crust of iron hydroxides limits the dissolution of silica on the top surface of tepuis. Dissolution in the subsurface, instead, is more significant and causes, in the long term, the “arenisation” of the quartz-sandstone and its subsequent removal by mechanical erosion. On the other hand, waters flowing on the arkosic rock outcropping on the lowland below the tepuis obtain their high dissolved silica content mainly from hydrolysis of silicates. The morphological evolution of these table mountains appears thus to be controlled mainly by the underground weathering of the quartz-sandstone, with the opening of deep fractures (grietas) and the collapse of large underground horizontal cave systems. Scarp retreat, instead, seems to be related to the higher weathering rate of the more arkosic formations underlying the quartz-sandstones.

  10. Some aspects of lithological and exogenic control of sandstone morphology, the Świętokrzyskie (Holy Cross) Mts. case study, Poland

    NASA Astrophysics Data System (ADS)

    Urban, Jan; Górnik, Marek

    2017-10-01

    Various morphologies of cliffs built of different quartzose rocks in the Świętokrzyskie (Holy Cross) Mts. (upland region, central Poland) - from Cambrian quartzites and Devonian quartzitic sandstones to Triassic and Jurassic porous sandstones - were described in order to examine the constraints of their lithological and spatial occurrence. The quantitative study of the occurrence of these morphologies on cliffs makes it possible to distinguish two principal groups of morphologies: angular relief produced by rock splitting (crumbling), typical of quartzites indurated in silica and of open porosity less than 1.5%, and morphologies developed due to granular disintegration and exfoliation of sandstones of open porosity higher than 1.5%. Among the relief types of this second group, morphology reflecting sedimentary and diagenetic structures as well as smooth surfaces are the most common and are referred to sandstones of a wide range of porosity, whereas honeycombs and surfaces suffering fast granular decay and scaling are characteristic of rocks of specific porosity (respectively: 5-8% and 3.5-8%). The occurrence of honeycombs on rock surfaces is also conditioned by exogenic factors: sun, wind and rain, since this morphology tends to occur on cliffs with aspects ranging from south-east, through south, to west-north-west.

  11. Fast fluidized bed steam generator

    DOEpatents

    Bryers, Richard W.; Taylor, Thomas E.

    1980-01-01

    A steam generator in which a high-velocity, combustion-supporting gas is passed through a bed of particulate material to provide a fluidized bed having a dense-phase portion and an entrained-phase portion for the combustion of fuel material. A first set of heat transfer elements connected to a steam drum is vertically disposed above the dense-phase fluidized bed to form a first flow circuit for heat transfer fluid which is heated primarily by the entrained-phase fluidized bed. A second set of heat transfer elements connected to the steam drum and forming the wall structure of the furnace provides a second flow circuit for the heat transfer fluid, the lower portion of which is heated by the dense-phase fluidized bed and the upper portion by the entrained-phase fluidized bed.

  12. Unraveling the stratigraphy of the Oriskany Sandstone: A necessity in assessing its site-specific carbon sequestration potential

    USGS Publications Warehouse

    Kostelnik, J.; Carter, K.M.

    2009-01-01

    The widespread distribution, favorable reservoir characteristics, and depth make the Lower Devonian Oriskany Sandstone a viable sequestration target in the Appalachian Basin. The Oriskany Sandstone is thickest in the structurally complex Ridge and Valley Province, thins toward the northern and western basin margins, and is even absent in other parts of the basin (i.e., the no-sand area of northwestern Pennsylvania). We evaluated four regions using petrographic data, core analyses, and geophysical log analyses. Throughout the entire study area, average porosities range from 1.35 to 14%. The most notable porosity types are primary intergranular, secondary dissolution, and fracture porosity. Intergranular primary porosity dominates at stratigraphic pinch-out zones near the Oriskany no-sand area and at the western limit of the Oriskany Sandstone. Secondary porosity occurs from dissolution of carbonate constituents primarily in the combination-traps natural gas play extending through western Pennsylvania, western West Virginia, and eastern Ohio. Fracture porosity dominates in the central Appalachian Plateau Province and Valley and Ridge Province. Based on average porosity, the most likely regions for successful sequestration in the Oriskany interval are (1) updip from Oriskany Sandstone pinch-outs in eastern Ohio, and (2) western Pennsylvania, western West Virginia, and eastern Ohio where production occurs from a combination of stratigraphic and structural traps. Permeability data, where available, were used to further evaluate the potential of these regions. Permeability ranges from 0.2 to 42.7 md. Stratigraphic pinch-outs at the northern and western limits of the basin have the highest permeabilities. We recommend detailed site assessments when evaluating the sequestration potential of a given injection site based on the variability observed in the Oriskany structure, lithology, and reservoir characteristics. ?? 2009. The American Association of Petroleum Geologists

  13. Depostional systems, provenance, and sequence stratigraphy, Carter and [open quotes]Millerella[close quotes] sandstones of northeast Mississippi

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Cleaves, A.W. II

    1993-09-01

    The subsurface [open quotes]Millerella[close quotes] and Carter sandstones (middle Chesterian) of the Black Warrior basin represent the highest units of the thick Muldon clastics deltaic facies tract. Lowstand marine conditions during Carter deposition allowed for southeastwardly progradation of five distinct deltaic lobe complexes onto the stable northern shelf of the basin. With each of these lobes, both an [open quotes]A[close quotes] (upper) and a [open quotes]B[close quotes] (lower) reservoir unit can be identified. The [open quotes]B[close quotes] sandstone produces from delta-front sheet sands, channel-mouth bars, and possible bar fingers of river-dominated deltas. The more prolific [open quotes]A[close quotes] subdivision containsmore » reservoirs in upper delta-plain point bars, crevasse splays, and distributary channel fills. The most easterly of the lobes, preserved in the Bean's Ferry field of Itawamba County, comprises an amalgamated valley-fill facies that removed a maximum of 250 ft (76 m) of lower Bangor platform carbonates. In contrast, the [open quotes]Millerella[close quotes] sandstone is a series of unconnected pods that formed as marine-reworked sand bodies during a eustatic rise in sea level. The average detrital sand grain composition for four cores taken in Monroe County is 94.7% monocrystalline quartz, 2.9% polycrystalline quartz, 1.6% albite feldspar, 0.1% low-rank metamorphic rock fragments, 0.5 chert, and 0.2% muscovite. These data indicate that neither the Ozark uplift nor the Ouachita orogen could have acted as the principal source area for the Carter and [open quotes]Millerella[close quotes] sandstones. More likely, the sedimentary-igneous terrains along the northern margin of the Illinois basin served this function. A major eustatic lowstand brought this mineralogically mature sediment across the Illinois basin through incised valleys to the northern self of the Black Warrior basin.« less

  14. Tectonic significance of porosity and permeability regimes in the red beds formations of the South Georgia Rift Basin

    NASA Astrophysics Data System (ADS)

    Akintunde, Olusoga M.; Knapp, Camelia C.; Knapp, James H.

    2014-09-01

    A simple, new porosity/permeability-depth profile was developed from available laboratory measurements on Triassic sedimentary red beds (sandstone) from parts of the South Georgia Rift (SGR) basin in order to investigate the feasibility for long-term CO2 storage. The study locations were: Sumter, Berkeley, Dunbarton, Clubhouse Crossroad-3 (CC-3) and Norris Lightsey wells. As expected, both porosity and permeability show changes with depth at the regional scale that was much greater than at local scale. The significant changes in porosity and permeability with depth suggest a highly compacted, deformed basin, and potentially, a history of uplift and erosion. The permeability is generally low both at shallow (less than 1826 ft/556.56 m) and deeper depths (greater than 1826 ft/556.56 m). Both porosity and permeability follow the normal trend, decreasing linearly with depth for most parts of the study locations with the exception of the Norris Lightsey well. A petrophysical study on a suite of well logs penetrating the Norris Lightsey red beds at depths sampled by the core-derived laboratory measurements shows an abnormal shift (by 50%) in the acoustic travel time and/or in the sonic-derived P-wave velocity that indicates possible faulting or fracturing at depth. The departure of the Norris Lightsey's porosities and permeabilities from the normal compaction trend may be a consequence of the existence of a fault/fracture controlled abnormal pressure condition at depth. The linear and non-linear behaviors of the porosity/permeability distribution throughout the basin imply the composition of the SGR red beds, and by extension analog/similar Triassic-Jurassic formations within the Eastern North American Margin have been altered by compaction, uplift, erosion and possible faulting that have shaped the evolution of these Triassic formations following the major phase of rifting.

  15. High-resolution mapping of yield curve shape and evolution for high porosity sandstones

    NASA Astrophysics Data System (ADS)

    Bedford, J. D.; Faulkner, D.; Wheeler, J.; Leclere, H.

    2017-12-01

    The onset of permanent inelastic deformation for porous rock is typically defined by a yield curve plotted in P-Q space, where P is the effective mean stress and Q is the differential stress. Sandstones usually have broadly elliptical shaped yield curves, with the low pressure side of the ellipse associated with localized brittle faulting (dilation) and the high pressure side with distributed ductile deformation (compaction). However recent works have shown that these curves might not be perfectly elliptical and that significant evolution in shape occurs with continued deformation. We therefore use a novel stress-probing methodology to map in high-resolution the yield curve shape for Boise and Idaho Gray sandstones (36-38% porosity) and also investigate curve evolution with increasing deformation. The data reveal yield curves with a much flatter geometry than previously recorded for porous sandstone and that the compactive side of the curve is partly comprised of a near vertical limb. The yield curve evolution is found to be strongly dependent on the nature of inelastic strain. Samples that were compacted under a deviatoric load, with a component of inelastic shear strain, were found to have yield curves with peaks that are approximately 50% higher than similar porosity samples that were hydrostatically compacted (i.e. purely volumetric strain). The difference in yield curve evolution along the different loading paths is attributed to mechanical anisotropy that develops during deviatoric loading by the closure of preferentially orientated fractures. Increased shear strain also leads to the formation of a plateau at the peak of the yield curve as samples deform along the deviatoric loading path. These results have important implications for understanding how the strength of porous rock evolves along different stress paths, including during fluid extraction from hydrocarbon reservoirs where the stress state is rarely isotropic.

  16. Persistence of aldicarb residues in the sandstone aquifer of Prince Edward Island, Canada

    NASA Astrophysics Data System (ADS)

    Jackson, R. E.; Mutch, J. P.; Priddle, M. W.

    1990-07-01

    Aldicarb residues were found in theshallow groundwaters of the fractured, aquifer of Prince Edward Island, Canada more than two years after the last application of this pesticide. Furthermore, the concentrations of aldicarb measured were relatively constant with time. The chemical and hydrogeological mechanisms by which such persistence occurs are discussed. It is deduced that the detoxifying abiotic transformation (hydrolysis) of aldicarb is inhibited by the low pH and temperature of the soil and groundwater, the former being partly due to the pH-buffering effects of ammonium fertilizer oxidation. Aldicarb residues remain constant and relatively high because of their storage within the sandstone matrix subsequent diffusion back into the fractures of this dual porosity system. Attempts to stimulate the observed persistence of aldicarb in this hydrogeologic environment using a one-dimensional, solute transport simulation code were unsuccessful, probably because of the three-dimensional nature of the matrix diffusion process. The simulations suggested that the overall half-life for aldicarb in the till-sandstone system approaches 150 days.

  17. Improving bed turnover time with a bed management system.

    PubMed

    Tortorella, Frank; Ukanowicz, Donna; Douglas-Ntagha, Pamela; Ray, Robert; Triller, Maureen

    2013-01-01

    Efficient patient throughput requires a high degree of coordination and communication. Opportunities abound to improve the patient experience by eliminating waste from the process and improving communication among the multiple disciplines involved in facilitating patient flow. In this article, we demonstrate how an interdisciplinary team at a large tertiary cancer center implemented an electronic bed management system to improve the bed turnover component of the patient throughput process.

  18. Strength, Deformation and Friction of in situ Rock

    DTIC Science & Technology

    1974-12-01

    Kayenta sandstone, Mixed Company site, Colorado. 30 21. Strength as a function of density for specimen cored perpendicular and parallel to bedding. 30...saturation. 33 24. Photomicrograph of Kayenta sandstone (x 30). 35 25. Stress difference as a function of density for triaxial tests up to P = 4.0...specimen size on strength for Kayenta sandstone, Mixed Company site Colorado. m Sä £ 3 s Q 3/« In, j. O 2 In. X ’ X3/4(n.ll • 2ln. II it

  19. Structural and microstructural evolution of fault zones in Cretaceous poorly lithified sandstones of the Rio do Peixe basin, Paraiba, NE Brazil

    NASA Astrophysics Data System (ADS)

    Balsamo, Fabrizio; Nogueira, Francisco; Storti, Fabrizio; Bezerra, Francisco H. R.; De Carvalho, Bruno R.; André De Souza, Jorge

    2017-04-01

    In this contribution we describe the structural architecture and microstructural features of fault zones developed in Cretaceous, poorly lithified sandstones of the Rio do Peixe basin, NE Brazil. The Rio do Peixe basin is an E-W-trending, intracontinental half-graben basin developed along the Precambrian Patos shear zone where it is abutted by the Porto Alegre shear zone. The basin formed during rifting between South America and Africa plates and was reactivated and inverted in a strike-slip setting during the Cenozoic. Sediments filling the basin consist of an heterolithic sequence of alternating sandstones, conglomerates, siltstone and clay-rich layers. These lithologies are generally poorly lithified far from the major fault zones. Deformational structures in the basin mostly consist of deformation band-dominated fault zones. Extensional and strike-slip fault zones, clusters of deformation bands, and single deformation bands are commonly well developed in the proximity of the basin-boundary fault systems. All deformation structures are generally in positive relief with respect to the host rocks. Extensional fault zones locally have growth strata in their hangingwall blocks and have displacement generally <10 m. In map view, they are organized in anastomosed segments with high connectivity. They strike E-W to NE-SW, and typically consist of wide fault cores (< 1 m in width) surrounded by up to few-meter wide damage zones. Fault cores are characterized by distributed deformation without pervasive strain localization in narrow shear bands, in which bedding is transposed into foliation imparted by grain preferred orientation. Microstructural observations show negligible cataclasis and dominant non-destructive particulate flow, suggesting that extensional fault zones developed in soft-sediment conditions in a water-saturated environment. Strike-slip fault zones commonly overprint the extensional ones and have displacement values typically lower than about 2 m. They

  20. Spatial distribution of epibenthic molluscs on a sandstone reef in the Northeast of Brazil.

    PubMed

    Martinez, A S; Mendes, L F; Leite, T S

    2012-05-01

    The present study investigated the distribution and abundance of epibenthic molluscs and their feeding habits associated to substrate features (coverage and rugosity) in a sandstone reef system in the Northeast of Brazil. Rugosity, low coral cover and high coverage of zoanthids and fleshy alga were the variables that influenced a low richness and high abundance of a few molluscan species in the reef habitat. The most abundant species were generalist carnivores, probably associated to a lesser offer and variability of resources in this type of reef system, when compared to the coral reefs. The results found in this study could reflect a normal characteristic of the molluscan community distribution in sandstone reefs, with low coral cover, or could indicate a degradation state of this habitat if it is compared to coral reefs, once that the significantly high coverage of fleshy alga has been recognized as a negative indicator of reef ecosystems health.

  1. Petrophysics of low-permeability medina sandstone, northwestern Pennsylvania, Appalachian Basin

    USGS Publications Warehouse

    Castle, J.W.; Byrnes, A.P.

    1998-01-01

    Petrophysical core testing combined with geophysical log analysis of low-permeability, Lower Silurian sandstones of the Appalachian basin provides guidelines and equations for predicting gas producibility. Permeability values are predictable from the borehole logs by applying empirically derived equations based on correlation between in-situ porosity and in-situ effective gas permeability. An Archie-form equation provides reasonable accuracy of log-derived water saturations because of saturated brine salinities and low clay content in the sands. Although measured porosity and permeability average less than 6% and 0.1 mD, infrequent values as high as 18% and 1,048 mD occur. Values of effective gas permeability at irreducible water saturation (Swi) range from 60% to 99% of routine values for the highest permeability rocks to several orders of magnitude less for the lowest permeability rocks. Sandstones having porosity greater than 6% and effective gas permeability greater than 0.01 mD exhibit Swi less than 20%. With decreasing porosity, Swi sharply increases to values near 40% at 3 porosity%. Analysis of cumulative storage and flow capacity indicates zones with porosity greater than 6% generally contain over 90% of flow capacity and hold a major portion of storage capacity. For rocks with Swi < 20%, gas relative permeabilities exceed 45%. Gas relative permeability and hydrocarbon volume decrease rapidly with increasing Swi as porosity drops below 6%. At Swi above 40%, gas relative permeabilities are less than approximately 10%.

  2. The Influence of Relative Submergence on the Near-bed Flow Field: Implications for Bed-load Transport

    NASA Astrophysics Data System (ADS)

    Cooper, J.; Tait, S.; Marion, A.

    2005-12-01

    Bed-load is governed by interdependent mechanisms, the most significant being the interaction between bed roughness, surface layer composition and near-bed flow. Despite this, practically all transport rate equations are described as a function of average bed shear stress. Some workers have examined the role of turbulence in sediment transport (Nelson et al. 1995) but have not explored the potential significance of spatial variations in the near-bed flow field. This is unfortunate considering evidence showing that transport is spatially heterogeneous and could be linked to the spatial nature of the near-bed flow (Drake et al., 1988). An understanding is needed of both the temporal and spatial variability in the near-bed flow field. This paper presents detailed spatial velocity measurements of the near-bed flow field over a gravel-bed, obtained using Particle Image Velocimetry. These data have been collected in a laboratory flume under two regimes: (i) tests with one bed slope and different flow depths; and (ii) tests with a combination of flow depths and slopes at the same average bed shear stress. Results indicate spatial variation in the streamwise velocities of up to 45 per cent from the double-averaged velocity (averaged in both time and space). Under both regimes, as the depth increased, spatial variability in the flow field increased. The probability distributions of near-bed streamwise velocities became progressively more skewed towards the higher velocities. This change was more noticeable under regime (i). This has been combined with data from earlier tests in which the near-bed velocity close to an entraining grain was measured using a PIV/image analysis system (Chegini et al, 2002). This along with data on the shape of the probability density function of velocities capable of entraining individual grains derived from a discrete-particle model (Heald et al., 2004) has been used to estimate the distribution of local velocities required for grain motion in

  3. Sedimentary structures and stratal geometries at the foothills of Mount Sharp: their role in paleoenvironmental interpretation

    NASA Astrophysics Data System (ADS)

    Gupta, S.; Rubin, D. M.; Sumner, D. Y.; Grotzinger, J. P.; Lewis, K. W.; Stack, K.; Kah, L. C.; Banham, S.; Edgett, K. S.

    2015-12-01

    The Mars Science Laboratory Curiosity rover has been exploring sedimentary rocks at the foothills of Mount Sharp since August 2014. Robust interpretation of the paleoenvironmental contexts requires detailed facies analysis of these rocks including analysis and interpretation of sedimentary structures and sediment body geometries. Here, we describe some of the detailed sedimentary structures and sedimentary geometries observed by Curiosity between the Pahrump_Hills field site and its current location at Marias Pass. The Pahrump Hills sedimentary section comprises a succession dominated by finely laminated mudstones of the Murray formation that are interpreted to have been deposited in an ancient lake within Gale crater. Toward the top of the Pahump Hills succession, we observe the appearance of coarser-grained sandstones that are interstratified within the lacustrine mudstones. These sandstones that include Whale Rock and Newspaper Rock show lenticular geometries, and are pervasively cross-stratified. These features indicate that currents eroded shallow scours in the lake beds that were then infilled by deposition from migrating subaqueous dunes. The paleoenvironmental setting may represent either a gullied delta front setting or one in which lake level fall caused fluvial erosion and infilling of the shallow scours. Since leaving Pahrump_Hills, Curiosity has imaged extensive exposures of strata that are partly correlative with and stratigraphically overlie the uppermost part of the Pahrump section. Isolated cross-bedded sandstones and possible interstratified conglomerates beds occur within Murray formation mudstones. Capping sandstones with a likely variety of environmental contexts overlie mudstones. Where imaged in detail, sedimentary structures, such as trough-cross bedding and possible eolian pinstriping, provide constraints on plausible sedimentary processes and bounds on depositional setting.

  4. Bed material agglomeration during fluidized bed combustion. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brown, R.C.; Dawson, M.R.; Smeenk, J.L.

    The purpose of this project is to determine the physical and chemical reactions which lead to the undesired agglomeration of bed material during fluidized bed combustion of coal and to relate these reactions to specific causes. A survey of agglomeration and deposit formation in industrial fluidized bed combustors (FBCs) indicate that at least five boilers were experiencing some form of bed material agglomeration. Deposit formation was reported at nine sites with deposits most commonly at coal feed locations and in cyclones. Other deposit locations included side walls and return loops. Three general types of mineralogic reactions were observed to occurmore » in the agglomerates and deposits. Although alkalies may play a role with some {open_quotes}high alkali{close_quotes} lignites, we found agglomeration was initiated due to fluxing reactions between iron (II) from pyrites and aluminosilicates from clays. This is indicated by the high amounts of iron, silica, and alumina in the agglomerates and the mineralogy of the agglomerates. Agglomeration likely originated in the dense phase of the FBC bed within the volatile plume which forms when coal is introduced to the boiler. Secondary mineral reactions appear to occur after the agglomerates have formed and tend to strengthen the agglomerates. When calcium is present in high amounts, most of the minerals in the resulting deposits are in the melilite group (gehlenite, melilite, and akermanite) and pyroxene group (diopside and augite). During these solid-phase reactions, the temperature of formation of the melilite minerals can be lowered by a reduction of the partial pressure of CO{sub 2} (Diopside + Calcite {r_arrow}Akermanite).« less

  5. Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence

    PubMed Central

    Wang, Changlu; Wen, Xiujun

    2011-01-01

    The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We conducted telephone interviews of staff from 77 Health and Epidemic Prevention Stations in six Chinese cities in November 2010. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F.)) are known to occur in China. These were common urban pests before the early1980s. Nationwide “Four-Pest Elimination” campaigns (bed bugs being one of the targeted pests) were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts). Although international and domestic travel has increased rapidly in China over the past decade (2000–2010), there have only been sporadic new infestations reported in recent years. During 1999–2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons), hotels, or trains. One city (Shenzhen city near Hong Kong) experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates). There have not been any studies or reports on bed bug insecticide

  6. Stratigraphic sections of Middle Jurassic Entrade sandstone and related rocks from Salt Valley to Dewey Bridge in East-Central Utah

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    O'Sullivan, R.B.

    1981-01-01

    The San Rafael Group of Middle Jurassic age form extensive dip slopes on the north side of Salt Valley and crops out in bold cliffs from Salt Wash eastward to Dewey Bridge. In the San Rafael Swell about 70 km west of Salt Valley; the San Rafael Group consists in ascending order of Page Sandstone, Carmel Formation, Entrada Sandstone, and the Curtis and Summerville Formations. Fifteen stratigraphic sections are included on the map interpretation of the stratigraphy aids petroleum and natural gas investigations. (DP)

  7. Applying tracer techniques to determine recharge rate, groundwater age and travel times in Permo-Triassic sandstones.

    NASA Astrophysics Data System (ADS)

    Butcher, Andrew; Gallagher, Alexander; Darling, W. George; Gooddy, Daren; Burke, Sean

    2010-05-01

    The Eden Valley in East Cumbria is underlain by Permo-Triassic sandstone, the major aquifer in Northwest England. Rising nitrate trends in some boreholes has prompted collaborative research into flow systems and timescales in the area. The use of slurry and artificial fertilisers following agricultural intensification during the 1980s is believed to be responsible for the rise in nitrate concentrations. The broad aim of this research is to enable prediction of future nitrate concentrations at abstraction boreholes and in groundwater discharge to surface water. The approach taken has been to study groundwater processes along a 4km transect (approximating a groundwater flowline) in order to estimate groundwater travel timescales through the sandstone and thin superficial Till . A combination of porewater sampling during borehole coring, discrete interval sampling using a borehole packer system, geophysical logging and imaging were employed to develop physical and hydrochemical profiles. Separate tracer techniques were used to estimate recharge rates at different parts of the transect. Tracers used were: deuterium and bromide through Till, nitrate, chloride and tritium through the unsaturated zone and CFCs and SF6 within the saturated zone. Tracer profiles in Till demonstrated a correspondence between Till thickness, type of cultivation and recharge rate. In the thick unsaturated zone of the sandstone they suggested relatively rapid groundwater recharge rates. Key fractures or fracture zones in the saturated sandstone were identified and sampled. The hydrochemistry (particularly nitrate) of samples from discrete intervals in the profiles exhibited a remarkably good relationship with the proportion of modern water (and year of recharge) for example, the age of groundwater increasing to c. 1950 towards the bottom of a 90m borehole. This work demonstrates that the combination of discrete sampling and dating of groundwater is a powerful tool in characterising groundwater

  8. Environmental Transitions Recorded by Fluvial Fan Stratigraphy at Dingo Gap and Moonlight Valley, Gale Crater, Mars

    NASA Astrophysics Data System (ADS)

    Edgar, L. A.; Gupta, S.; Rubin, D. M.; Schieber, J.; Stack, K.; Lewis, K. W.

    2016-12-01

    The Mars Science Laboratory (MSL) Curiosity rover investigated a number of sedimentary outcrops across Aeolis Palus. Observations of conglomerates, cross-bedded sandstones, and mudstones suggest that fluvial and lacustrine environments were common. Outcrops that expose cross-sections are particularly helpful for identifying stratigraphic relationships and changes through time. In the vicinity of an outcrop informally named Dingo Gap, the drive strategy shifted from driving on the topographic high areas to the topographic low areas, which resulted in a unique vantage point to observe stratigraphy in cross-section. During Sols 513-541, Curiosity investigated 4 m of stratigraphy exposed at Dingo Gap and Moonlight Valley. The valley walls reveal five distinct sedimentary facies, including 1) a fine-grained evenly laminated facies interpreted as upper plane bed stratification, 2) ripple and dune cross-stratified sandstone facies, interpreted to represent the southward migration of subaqueous bedforms, 3) fully preserved bedform sandstone facies, formed during high rates of deposition, 4) planar-bedded granule-rich sandstone facies, interpreted as sheet flood deposits, and 5) a weakly stratified, poorly-sorted conglomerate facies, interpreted to represent rapid deposition from a high-energy fluvial flow. The conglomerate facies is unlike other conglomerates observed thus far in the mission, on the basis of both texture and chemistry. Analysis of conglomerates reveal that they occur as distinct channel bodies, incised into cross-stratified sandstones. This coarsening upward signature is interpreted to record a prograding fan succession. Channel bodies appear to be time-equivalent, which suggests a major change in the system, likely associated with a drop in base level. The unique viewing geometry offered by Dingo Gap and Moonlight Valley makes it possible to observe these environmental changes.

  9. Pulse enhanced fluidized bed combustion

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mueller, B.

    1996-12-31

    Information is outlined on pulse enhanced fluidized bed combustion. The following topics are discussed: what is pulse enhanced fluidized bed combustion?; pulse combustors; pulsed atmospheric fluidized bed combustor (PAFBC); advantages of PAFBC; performance advantages; PAFBC facts; and PAFBC contact points.

  10. Ancient sandstone condition assessment in relation to degradation, cleaning and consolidation phenomena

    NASA Astrophysics Data System (ADS)

    Drdácký, Miloš; Frankeová, Dita; Slížková, Zuzana

    2015-04-01

    Non-invasive methods for assessing the state of historic stone types rely on measurement of their surface or subsurface characteristics, which are supposed to correlate with objective physical characteristics. Such measurements are influenced by surface conditions of stone, as well as by previous conservation treatments. The authors performed a comprehensive study of characteristics and behaviour of typical sandstone types present in the Charles' Bridge in Prague as a preparatory work for its diagnostic and restoration in order to understand the problem of a large, important, and non-homogeneous (from the material point of view) historic structure, that was intended for repair interventions. The study itself took advantage of the combination of non-invasive, or considerately destructive methods and fully destructive tests, because it was possible to use damaged sandstone blocks, which were extracted from a masonry rail of the bridge before replacement with new elements. Stone characteristics were studied on test specimens prepared from materials in various conditions and after various interventions. Seven types of sandstone were tested in nine sets (degraded surface layer with a crust, degraded surface layer after cleaning, and unweathered core material; all three without any consolidation treatment, and all three after consolidation with two products based on silicic acid ester - Funcosil 100 and 300). The paper will present only selected results of experiments and the most important conclusions taken from the tests and their comparison. During experimental work the following characteristics were investigated: bending strength, modulus of elasticity, ultrasonic velocity, micro-drilling resistance, water uptake, porosity, frost resistance, hydric dilation and thermal dilation. The degraded stone had a rather strong variation of its characteristics along the depth profile from the surface inside the stone ashlar. Therefore, the stone samples were prepared in a form

  11. From Modern Push-Button Hospital-beds to 20th Century Mechatronic Beds: A Review

    NASA Astrophysics Data System (ADS)

    Ghersi, I.; Mariño, M.; Miralles, M. T.

    2016-04-01

    The aim of this work is to present the different aspects of modern high complexity electric beds of the period 1940 until 2000 exclusively. The chronology of the product has been strictly divided into three big stages: electric and semi-electric beds (until the 90’s), mechatronic beds (90’s until 2000) and, mechatronic intelligent beds of the last 15 years. The latter are not considered in this work due to the extension for its analysis. The justification for classifying the product is presented under the concepts of medical, assistive and mobility devices. Relevant aspects of common immobility problems of the different types of patients for which the beds are mainly addressed are shown in detail. The basic functioning of the patient’s movement generator and the implementation of actuators, together with IT programs, specific accessories and connectivity means and network-communication shown in this work, were those that gave origin to current mechatronic beds. We present the historical evolution of high complexity electric beds by illustrating cases extracted from a meticulous time line, based on patents, inventions and publications in newspapers and magazines of the world. The criteria adopted to evaluate the innovation were: characteristics of controls; accessories (mattresses, lighting, siderails, etc.), aesthetic and morphologic properties and outstanding functionalities.

  12. Coupling Aeolian Stratigraphic Architecture to Paleo-Boundary Conditions: The Scour-Fill Dominated Jurassic Page Sandstone

    NASA Astrophysics Data System (ADS)

    Cardenas, B. T.; Kocurek, G.; Mohrig, D. C.; Swanson, T.

    2017-12-01

    The stratigraphic architecture of aeolian sandstones is thought to encode signals originating from both autogenic dune behavior and allogenic boundary conditions within which the dune field evolves. Mapping of outcrop-scale bounding surfaces and sets of cross-strata between these surfaces for the Jurassic Page Sandstone near Page, AZ, USA, demonstrates that dune autogenic behavior manifested in variable dune scour depth, whereas the dominant boundary conditions were antecedent topography and water-table elevation. At the study area, the Page Sandstone is 60 m thick and is separated from the underlying Navajo Sandstone by the J-2 regional unconformity, which shows meters of relief. Filling J-2 depressions are thin, climbing sets of cross-strata. In contrast, the overlying Page consists of packages of one to a few, meter-scale sets of cross-strata between the outcrop-scale bounding surfaces. These surfaces, marked by polygonal fractures and local overlying sabkha deposits, are regional in scale and correlated to high stands of the adjacent Carmel sea. Over the km-scale outcrop, the surfaces show erosional relief and packages of cross-strata are locally truncated. Notably absent within these cross-strata packages are early dune-field accumulations, interdune deposits, and apparent dune-climbing. These strata are interpreted to represent a scour-fill architecture created by migrating large dunes within a mature dry aeolian sand sea, in which early phases of dune-field construction have been cannibalized and dune fill of the deepest scours is recorded. At low angles of climb, set thickness is dominated by the component of scour-depth variation over the component resulting from the angle of climb. After filling of J-2 depressions, the Page consists of scour-fill accumulations formed during low stands. Carmel transgressions limited sediment availability, causing deflation to the water table and development of the regional bounding surfaces. Each subsequent fall of the

  13. Fluidized bed operations survey summary

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lombardi, C.

    1996-12-31

    A fluidized bed operations survey summary is presented. The survey contains information on: forced outage causes; forced outage concerns ranked numerically; 1996 boiler operation and maintenance (O&M) concerns; 1997 boiler O&M concerns; fluidized bed capacity factor results; and fluidized bed total outage time.

  14. Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence.

    PubMed

    Wang, Changlu; Wen, Xiujun

    2011-04-11

    The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We conducted telephone interviews of staff from 77 Health and Epidemic Prevention Stations in six Chinese cities in November 2010. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F.)) are known to occur in China. These were common urban pests before the early1980s. Nationwide "Four-Pest Elimination" campaigns (bed bugs being one of the targeted pests) were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts). Although international and domestic travel has increased rapidly in China over the past decade (2000-2010), there have only been sporadic new infestations reported in recent years. During 1999-2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons), hotels, or trains. One city (Shenzhen city near Hong Kong) experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates). There have not been any studies or reports on bed bug insecticide

  15. Constitutive Modelling and Deformation Band Angle Predictions for High Porosity Sandstones

    NASA Astrophysics Data System (ADS)

    Richards, M. C.; Issen, K. A.; Ingraham, M. D.

    2017-12-01

    The development of a field-scale deformation model requires a constitutive framework that is capable of representing known material behavior and able to be calibrated using available mechanical response data. This work employs the principle of hyperplasticity (e.g., Houlsby and Puzrin, 2006) to develop such a constitutive framework for high porosity sandstone. Adapting the works of Zimmerman et al. (1986) and Collins and Houlsby (1997), the mechanical data set of Ingraham et al. (2013 a, b) was used to develop a specific constitutive framework for Castlegate sandstone, a high porosity fluvial-deposited reservoir analog rock. Using the mechanical data set of Ingraham et al. (2013 a, b), explicit expressions and material parameters of the elastic moduli and strain tensors were obtained. With these expressions, analytical and numerical techniques were then employed to partition the total mechanical strain into elastic, coupled, and plastic strain components. With the partitioned strain data, yield surfaces in true-stress space, coefficients of internal friction, dilatancy factors, along with the theorectical predictions of the deformation band angles were obtained. These results were also evaluated against band angle values obtained from a) measurements on specimen jackets (Ingraham et al., 2013a), b) plane fits through located acoustic emissions (AE) events (Ingraham et al. 2013b), and c) X-ray micro-computed tomography (micro-CT) calculations.

  16. Seaweed beds support more juvenile reef fish than seagrass beds in a south-western Atlantic tropical seascape

    NASA Astrophysics Data System (ADS)

    Eggertsen, L.; Ferreira, C. E. L.; Fontoura, L.; Kautsky, N.; Gullström, M.; Berkström, C.

    2017-09-01

    Seascape connectivity is regarded essential for healthy reef fish communities in tropical shallow systems. A number of reef fish species use separate adult and nursery habitats, and hence contribute to nutrient and energy transfer between habitats. Seagrass beds and mangroves often constitute important nursery habitats, with high structural complexity and protection from predation. Here, we investigated if reef fish assemblages in the tropical south-western Atlantic demonstrate ontogenetic habitat connectivity and identify possible nurseries on three reef systems along the eastern Brazilian coast. Fish were surveyed in fore reef, back reef, Halodule wrightii seagrass beds and seaweed beds. Seagrass beds contained lower abundances and species richness of fish than expected, while Sargassum-dominated seaweed beds contained significantly more juveniles than all other habitats (average juvenile fish densities: 32.6 per 40 m2 in Sargassum beds, 11.2 per 40 m2 in back reef, 10.1 per 40 m2 in fore reef, and 5.04 per 40 m2 in seagrass beds), including several species that are found in the reef habitats as adults. Species that in other regions worldwide (e.g. the Caribbean) utilise seagrass beds as nursery habitats were here instead observed in Sargassum beds or back reef habitats. Coral cover was not correlated to adult fish distribution patterns; instead, type of turf was an important variable. Connectivity, and thus pathways of nutrient transfer, seems to function differently in east Brazil compared to many tropical regions. Sargassum-dominated beds might be more important as nurseries for a larger number of fish species than seagrass beds. Due to the low abundance of structurally complex seagrass beds we suggest that seaweed beds might influence adult reef fish abundances, being essential for several keystone species of reef fish in the tropical south-western Atlantic.

  17. Utility of Recycled Bedding for Laboratory Rodents

    PubMed Central

    Miyamoto, Toru; Li, Zhixia; Kibushi, Tomomi; Okano, Shinya; Yamasaki, Nakamichi; Kasai, Noriyuki

    2009-01-01

    Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this study, we examined the effects of bedding type on growth, hematologic and serum biochemical values, and organ weights of female and male mice reared on either recycled or fresh bedding from 3 to 33 wk of age. Neither growth nor physiology differed between mice housed on recycled bedding compared with fresh bedding. When 14-wk-old mice were bred, litter size and total number of weaned pups showed no significant differences between animals raised on recycled or fresh bedding. Because bedding type influences the environment within cages and animal rooms, we evaluated particulate and ammonia data from cages and animal rooms. Values were significantly lower from cages and rooms that used recycled bedding than from those using fresh bedding, thus indicating that recycled bedding has the potential to improve the environment within both cages and animal rooms. Overall, this study revealed that recycled bedding is an excellent material for use in housing laboratory rodents. Specifically, recycled bedding may reduce medical waste and maintain healthy environments within cages and animal rooms. PMID:19653951

  18. A two scale analysis of tight sandstones

    NASA Astrophysics Data System (ADS)

    Adler, P. M.; Davy, C. A.; Song, Y.; Troadec, D.; Hauss, G.; Skoczylas, F.

    2015-12-01

    Tight sandstones have a low porosity and a very small permeability K. Available models for K do not compare well with measurements. These sandstones are made of SiO_2 grains, with a typical size of several hundreds of micron. These grains are separated by a network of micro-cracks, with sizes ranging between microns down to tens of nm. Therefore, the structure can be schematized by Voronoi polyhedra separated by plane and permeable polygonal micro-cracks. Our goal is to estimate K based on a two scale analysis and to compare the results to measurements. For a particular sample [2], local measurements on several scales include FIB/SEM [3], CMT and 2D SEM. FIB/SEM is selected because the peak pore size given by Mercury Intrusion Porosimetry is of 350nm. FIB/SEM imaging (with 50 nm voxel size) identifies an individual crack of 180nm average opening, whereas CMT provides a connected porosity (individual crack) for 60 nm voxel size, of 4 micron average opening. Numerical modelling is performed by combining the micro-crack network scale (given by 2D SEM) and the 3D micro-crack scale (given by either FIB/SEM or CMT). Estimates of the micro-crack density are derived from 2D SEM trace maps by counting the intersections with scanlines, the surface density of traces, and the number of fracture intersections. K is deduced by using a semi empirical formula valid for identical, isotropic and uniformly distributed fractures [1]. This value is proportional to the micro-crack transmissivity sigma. Sigma is determined by solving the Stokes equation in the micro-cracks measured by FIB/SEM or CMT. K is obtained by combining the two previous results. Good correlation with measured values on centimetric plugs is found when using sigma from CMT data. The results are discussed and further research is proposed. [1] Adler et al, Fractured porous media, Oxford Univ. Press, 2012. [2] Duan et al, Int. J. Rock Mech. Mining Sci., 65, p75, 2014. [3] Song et al, Marine and Petroleum Eng., 65, p63

  19. Assessment of tight-gas resources in Canyon sandstones of the Val Verde Basin, Texas, 2016

    USGS Publications Warehouse

    Schenk, Christopher J.; Tennyson, Marilyn E.; Klett, Timothy R.; Mercier, Tracey J.; Brownfield, Michael E.; Gaswirth, Stephanie B.; Hawkins, Sarah J.; Leathers-Miller, Heidi M.; Marra, Kristen R.; Finn, Thomas M.; Pitman, Janet K.

    2016-07-08

    Using a geology-based assessment methodology, the U.S. Geological Survey assessed mean resources of 5 trillion cubic feet of gas and 187 million barrels of natural gas liquids in tight-gas assessment units in the Canyon sandstones of the Val Verde Basin, Texas.

  20. Improved lignin pyrolysis for phenolics production in a bubbling bed reactor--Effect of bed materials.

    PubMed

    Li, Dongbing; Briens, Cedric; Berruti, Franco

    2015-01-01

    Lignin pyrolysis was studied in a bubbling fluidized bed reactor equipped with a fractional condensation train, using nitrogen as the fluidization gas. The effect of different bed materials (silica sand, lignin char, activated lignin char, birch bark char, and foamed glass beads) on bio-oil yield and quality was investigated for a pyrolysis temperature of 550 °C. Results how that a bed of activated lignin char is preferable to the commonly used silica sand: pyrolysis of Kraft lignin with a bed of activated lignin char not only provides a pure char product, but also a higher dry bio-oil yield (with a relative increase of 43%), lower pyrolytic water production, and better bio-oil quality. The bio-oil obtained from Kraft lignin pyrolysis with a bed of activated lignin char has a lower average molecular weight, less tar, more phenolics, and less acidity than when sand is used as bed material. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Hydrogeology of the Pictured Cliffs Sandstone in the San Juan structural basin, New Mexico, Colorado, Arizona, and Utah

    USGS Publications Warehouse

    Dam, William L.; Kernodle, J.M.; Thorn, C.R.; Levings, G.W.; Craigg, S.D.

    1990-01-01

    This report is one in a series resulting from the U.S. Geological Survey's Regional Aquifer System Analysis (RASA) study of the San Juan structural basin that began in October 1984. The purposes of the study (Welder, 1986) are to: (1) Define and evaluate the aquifer system; (2) assess the effects of past, present, and potential ground-water use on aquifers and streams, and (3) determine the availability and quality of ground water. Previous reports in this series describe the hydrogeology of the Dakota Sandstone (Craigg and others, 1989), Gallup Sandstone (Kernodle and others, 1989), Morrison Formation (Dam and others, 1990), Point Lookout Sandstone (Craigg and others, 1990), Kirtland Shale and Fruitland Formation (Kernodle and others, 1990), Menefee Formation (Levings and others, 1990), Cliff House Sandstone (Thorn and others, 1990), and Ojo Alamo Sandstone (Thorn and others, 1990) in the San Juan structural basin. This report summarizes information on the geology and the occurrence and quality of water in the Pictured Cliffs Sandstone, one of the primary water-bearing units in the regional aquifer system. Data used in this report were collected during the RASA study or derived from existing records in the U.S. Geological Survey's computerized National Water Information System (NWIS) data base, the Petroleum Information Corporation's data base, and the Dwight's ENERGYDATA Inc. BRIN database. Although all data available for the Pictured Cliffs Sandstone were considered in formulating the discussions in the text, not all those data could be plotted on the illustrations. The San Juan structural basin in New Mexico, Colorado, Arizona, and Utah has an area of about 21,600 square miles (fig. 1). The structural basin is about 140 miles wide and about 200 miles long. The study area is that part of the structural basin that contains rocks of Triassic and younger age; therefore, the study area is less extensive than the structural basin. Triassic through Tertiary

  2. Pore Structure and Limit Pressure of Gas Slippage Effect in Tight Sandstone

    PubMed Central

    You, Lijun; Xue, Kunlin; Kang, Yili; Liao, Yi

    2013-01-01

    Gas slip effect is an important mechanism that the gas flow is different from liquid flow in porous media. It is generally considered that the lower the permeability in porous media is, the more severe slip effect of gas flow will be. We design and then carry out experiments with the increase of backpressure at the outlet of the core samples based on the definition of gas slip effect and in view of different levels of permeability of tight sandstone reservoir. This study inspects a limit pressure of the gas slip effect in tight sandstones and analyzes the characteristic parameter of capillary pressure curves. The experimental results indicate that gas slip effect can be eliminated when the backpressure reaches a limit pressure. When the backpressure exceeds the limit pressure, the measured gas permeability is a relatively stable value whose range is less than 3% for a given core sample. It is also found that the limit pressure increases with the decreasing in permeability and has close relation with pore structure of the core samples. The results have an important influence on correlation study on gas flow in porous medium, and are beneficial to reduce the workload of laboratory experiment. PMID:24379747

  3. Textural and mineralogical study of sandstones from the onshore Gulf of Alaska Tertiary Province, southern Alaska

    USGS Publications Warehouse

    Winkler, Gary R.; McLean, Hugh; Plafker, George

    1976-01-01

    Petrographic examination of 74 outcrop samples of Paleocene through Pliocene age from the onshore Gulf of Alaska Tertiary Province indicates that sandstones of the province characteristically are texturally immature and mineralogically unstable. Diagenetic alteration of framework grains throughout the stratigraphic sequence has produced widespread zeolite cement or phyllosilicate grain coatings and pseudomatrix. Multiple deformation and deep burial of the older Tertiary sequence--the Orca Group, the shale of Haydon Peak, and the Kulthieth and Tokun Formations--caused extensive alteration and grain interpenetration, resulting in low porosity values. Less intense deformation and intermediate depth of burial of the younger Tertiary sequence--the Katalla, Poul Creek, Redwood, and Yakataga Formations--has resulted in a greater range in textural properties. Most sandstone samples in the younger Tertiary sequence are poorly sorted, tightly packed, and have strongly appressed framework grains, but some are less tightly packed and contain less matrix. Soft and mineralogically unstable framework grains have undergone considerable alteration, reducing pore space even in the youngest rocks. Measurements of porosity, permeability, grain density, and sonic velocity of outcrop samples of the younger Tertiary sequence indicate a modest up-section improvement in sandstone reservoir characteristics. Nonetheless porosity and permeability values typically are below 16 percent and 15 millidarcies respectively and grain densities are consistently high, about 2.7 gm/cc. Low permeability and porosity values, and high grain densities and sonic velocities appear to be typical of most outcrop areas throughout the onshore Gulf of Alaska Tertiary Province.

  4. Fluidized bed deposition of diamond

    DOEpatents

    Laia, Jr., Joseph R.; Carroll, David W.; Trkula, Mitchell; Anderson, Wallace E.; Valone, Steven M.

    1998-01-01

    A process for coating a substrate with diamond or diamond-like material including maintaining a substrate within a bed of particles capable of being fluidized, the particles having substantially uniform dimensions and the substrate characterized as having different dimensions than the bed particles, fluidizing the bed of particles, and depositing a coating of diamond or diamond-like material upon the substrate by chemical vapor deposition of a carbon-containing precursor gas mixture, the precursor gas mixture introduced into the fluidized bed under conditions resulting in excitation mechanisms sufficient to form the diamond coating.

  5. The effects of steam injection in a sandstone reservoir (Etchegoin Formation), Buena Vista field, California

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Grant, C.W.; Reed, A.A.

    1991-03-01

    At Buena Vista field, California, 120 ft of post-steamflood core, spanning the middle Pliocene Wilhelm Member of the Etchegoin Formation, was taken to assess the influence of stratigraphy on light-oil steamflood (LOSF) processes and to determine what steam-rock reactions occurred and how these affected reservoir properties. High-quality steam (600F (300C)) had been injected ({approximately}1,700 psi) into mixed tidal flat and estuarine facies in an injector well located 55 ft from the cored well. Over a period of 20 months, steam rapidly channeled through a thin ({approximately}7 ft), relatively permeable (1-1,000 md), flaser-bedded sandstone unit. Conductive heating above this permeable unitmore » produced, in the vicinity of the cored well, a 35-ft steam-swept zone (oil saturation = 0), overlain by a 29-ft steam-affected zone in which oil saturation had been reduced to 13%, far below the presteam saturation of 30%. Steam-induced alteration ('artificial diagenesis') of the clay-rich reservoir rock was recognized using SEM, petrography, and X-ray diffraction. Salient dissolution effects were the complete to partial removal of siliceous microfossils, Fe-dolomite, volcanic rock fragments, and labile heavy minerals. The artificial diagenetic effects are first encountered in the basal 6 ft of the 29-ft steam-affected zone. Based on the distribution of the authigenic phases, the authors conclude that the reactions took place, or were at least initiated, in the steam condensate bank ahead of the advancing steam front. Although these changes presumably reduced permeability, the steamflood process was effective in reducing oil saturation to zero in the steam-contacted portion of the reservoir.« less

  6. Displacement front behavior of near miscible CO2 flooding in decane saturated synthetic sandstone cores revealed by magnetic resonance imaging.

    PubMed

    Liu, Yu; Teng, Ying; Jiang, Lanlan; Zhao, Jiafei; Zhang, Yi; Wang, Dayong; Song, Yongchen

    2017-04-01

    It is of great importance to study the CO 2 -oil two-phase flow characteristic and displacement front behavior in porous media, for understanding the mechanisms of CO 2 enhanced oil recovery. In this work, we carried out near miscible CO 2 flooding experiments in decane saturated synthetic sandstone cores to investigate the displacement front characteristic by using magnetic resonance imaging technique. Experiments were done in three consolidated sandstone cores with the permeabilities ranging from 80 to 450mD. The oil saturation maps and the overall oil saturation during CO 2 injections were obtained from the intensity of magnetic resonance imaging. Finally the parameters of the piston-like displacement fronts, including the front velocity and the front geometry factor (the length to width ratio) were analyzed. Experimental results showed that the near miscible vertical upward displacement is instable above the minimum miscible pressure in the synthetic sandstone cores. However, low permeability can restrain the instability to some extent. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. High-temperature quartz cement and the role of stylolites in a deep gas reservoir, Spiro Sandstone, Arkoma Basin, USA

    USGS Publications Warehouse

    Worden, Richard H.; Morad, Sadoon; Spötl, C.; Houseknecht, D.W.; Riciputi, L.R.

    2000-01-01

    The Spiro Sandstone, a natural gas play in the central Arkoma Basin and the frontal Ouachita Mountains preserves excellent porosity in chloritic channel-fill sandstones despite thermal maturity levels corresponding to incipient metamorphism. Some wells, however, show variable proportions of a late-stage, non-syntaxial quartz cement, which post-dated thermal cracking of liquid hydrocarbons to pyrobitumen plus methane. Temperatures well in excess of 150°C and possibly exceeding 200°C are also suggested by (i) fluid inclusions in associated minerals; (ii) the fact that quartz post-dated high-temperature chlorite polytype IIb; (iii) vitrinite reflectance values of the Spiro that range laterally from 1.9 to ≥ 4%; and (iii) the occurrence of late dickite in these rocks. Oxygen isotope values of quartz cement range from 17.5 to 22.4‰ VSMOW (total range of individual in situ ion microprobe measurements) which are similar to those of quartz cement formed along high-amplitude stylolites (18.4–24.9‰). We favour a model whereby quartz precipitation was controlled primarily by the availability of silica via deep-burial stylolitization within the Spiro Sandstone. Burial-history modelling showed that the basin went from a geopressured to a normally pressured regime within about 10–15 Myr after it reached maximum burial depth. While geopressure and the presence of chlorite coats stabilized the grain framework and inhibited nucleation of secondary quartz, respectively, stylolites formed during the subsequent high-temperature, normal-pressured regime and gave rise to high-temperature quartz precipitation. Authigenic quartz growing along stylolites underscores their role as a significant deep-burial silica source in this sandstone.

  8. Role of Grain Crushing in the Alteration of Mechanical and Flow Properties of Sandstones during Mechanical Failure

    NASA Astrophysics Data System (ADS)

    Mirabolghasemi, M.; Prodanovic, M.; Choens, R. C., II; Dewers, T. A.

    2016-12-01

    We present a workflow to study the alteration of flow and mechanical characteristics of sandstones after shear failure, specifically modeling weakening of the formation due to CO2 injection. We use discrete elements method (DEM) to represent each sand grain as a cluster of bonded sub-particles, and model their potential crushing. We also introduce bonds between sand grain clusters to enable the modeling of the mechanical behavior of consolidated sandstones. The model is tuned by comparing our numerical compression tests on single sand grains with the experimental results reported in the literature. Once the mechanical behavior of individual grains is adequately captured by the model, a packing of such grains is subjected to shear stress. Once the packing fails under the imposed shear stress, its mechanical properties, permeability, and porosity are calculated. This test is repeated for various conditions by varying parameters such as the brittleness of single grains (the relative quartz-feldspar content of the grains), normal stress, and cement strength (assuming (chemical) weakening of the inter- and intra-grain-cluster bonds due to CO2 injection). We specifically compare the effect of cement/bond strength weakening on mechanical properties to triaxial compression experimental measurements before and after hydrous scCO2 and CO2-saturated brine injection in Boise sandstone performed in Sandia National Laboratory.

  9. The dominance of dispersion in the evolution of bed material waves in gravel-bed rivers

    Treesearch

    Thomas E. Lisle; Yantao Cui; Gary Parker; James E. Pizzuto; Annjanette M. Dodd

    2001-01-01

    Abstract - Bed material waves are temporary zones of sediment accumulation created by large sediment inputs. Recent theoretical, experimental and field studies examine factors in fluencing dispersion and translation of bed material waves in quasi-uniform, gravel-bed channels. Exchanges of sediment between a channel and its floodplain are...

  10. Statistical description of flume experiments on mixed-size bed-load transport and bed armoring processes

    NASA Astrophysics Data System (ADS)

    Chen, D.; Zhang, Y.

    2008-12-01

    The objective of this paper is to describe the statistical properties of experiments on non-uniform bed-load transport as well as the mechanism of bed armoring processes. Despite substantial effort made over the last two decades, the ability to compute the bed-load flux in a turbulent system remains poor. The major obstacles include the poor understanding of the formation of armor lays on bed surfaces. Such a layer is much flow-resistible than the underlying material and therefore significantly inhibits sediment transport from the reach. To study the problem, we conducted a flume study for mixed sand/gravel sediments. We observed that aggregated sediment blocks were the most common characters in armor layers - the largest sizes resist hydraulic forces, while the smaller sizes add interlocking support and prevent loss of fine material through gaps between the larger particles. Fractional transport rates with the existing of armor layers were measured with time by sediment trapping method at the end of flume. To address the intermittent and time-varying behavior of bed-load transport during bed armoring processes, we investigated the probability distribution of the fractional bed-load transport rates, and the underlying dynamic model derived from the continuous time random walk framework. Results indicate that it is critical to consider the impact of armor layers when a flow is sufficient to move some of the finer particles and yet insufficient to move all the larger particles on a channel bed.

  11. Staged fluidized-bed combustion and filter system

    DOEpatents

    Mei, Joseph S.; Halow, John S.

    1994-01-01

    A staged fluidized-bed combustion and filter system for substantially reducing the quantity of waste through the complete combustion into ash-type solids and gaseous products. The device has two fluidized-bed portions, the first primarily as a combustor/pyrolyzer bed, and the second as a combustor/filter bed. The two portions each have internal baffles to define stages so that material moving therein as fluidized beds travel in an extended route through those stages. Fluidization and movement is achieved by the introduction of gases into each stage through a directional nozzle. Gases produced in the combustor/pyrolyzer bed are permitted to travel into corresponding stages of the combustor/filter bed through screen filters that permit gas flow but inhibit solids flow. Any catalyst used in the combustor/filter bed is recycled. The two beds share a common wall to minimize total volume of the system. A slightly modified embodiment can be used for hot gas desulfurization and sorbent regeneration. Either side-by-side rectangular beds or concentric beds can be used. The system is particularly suited to the processing of radioactive and chemically hazardous waste.

  12. Architectural elements from Lower Proterozoic braid-delta and high-energy tidal flat deposits in the Magaliesberg Formation, Transvaal Supergroup, South Africa

    NASA Astrophysics Data System (ADS)

    Eriksson, Patrick G.; Reczko, Boris F. F.; Jaco Boshoff, A.; Schreiber, Ute M.; Van der Neut, Markus; Snyman, Carel P.

    1995-06-01

    Three architectural elements are identified in the Lower Proterozoic Magaliesberg Formation (Pretoria Group, Transvaal Supergroup) of the Kaapvaal craton, South Africa: (1) medium- to coarse-grained sandstone sheets; (2) fine- to medium-grained sandstone sheets; and (3) mudrock elements. Both sandstone sheet elements are characterised by horizontal lamination and planar cross-bedding, with lesser trough cross-bedding, channel-fills and wave ripples, as well as minor desiccated mudrock partings, double-crested and flat-topped ripples. Due to the local unimodal palaeocurrent patterns in the medium- to coarse-grained sandstone sheets, they are interpreted as ephemeral braid-delta deposits, which were subjected to minor marine reworking. The predominantly bimodal to polymodal palaeocurrent trends in the fine- to medium-grained sandstone sheets are inferred to reflect high-energy macrotidal processes and more complete reworking of braid-delta sands. The suspension deposits of mudrocks point to either braid-delta channel abandonment, or uppermost tidal flat sedimentation. The depositional model comprises ephemeral braid-delta systems which debouched into a high-energy peritidal environment, around the margins of a shallow epeiric sea on the Kaapvaal craton. Braid-delta and tidal channel dynamics are inferred to have been similar. Fine material in the Magaliesberg Formation peritidal complexes indicates that extensive aeolian removal of clay does not seem applicable to this example of the early Proterozoic.

  13. Spatial Distribution of Bed Particles in Natural Boulder-Bed Streams

    NASA Astrophysics Data System (ADS)

    Clancy, K. F.; Prestegaard, K. L.

    2001-12-01

    The Wolman pebble count is used to obtain the size distribution of bed particles in natural streams. Statistics such as median particle size (D50) are used in resistance calculations. Additional information such as bed particle heterogeneity may also be obtained from the particle distribution, which is used to predict sediment transport rates (Hey, 1979), (Ferguson, Prestegaard, Ashworth, 1989). Boulder-bed streams have an extreme range of particles in the particle size distribution ranging from sand size particles to particles larger than 0.5-m. A study of a natural boulder-bed reach demonstrated that the spatial distribution of the particles is a significant factor in predicting sediment transport and stream bed and bank stability. Further experiments were performed to test the limits of the spatial distribution's effect on sediment transport. Three stream reaches 40-m in length were selected with similar hydrologic characteristics and spatial distributions but varying average size particles. We used a grid 0.5 by 0.5-m and measured four particles within each grid cell. Digital photographs of the streambed were taken in each grid cell. The photographs were examined using image analysis software to obtain particle size and position of the largest particles (D84) within the reach's particle distribution. Cross section, topography and stream depth were surveyed. Velocity and velocity profiles were measured and recorded. With these data and additional surveys of bankfull floods, we tested the significance of the spatial distributions as average particle size decreases. The spatial distribution of streambed particles may provide information about stream valley formation, bank stability, sediment transport, and the growth rate of riparian vegetation.

  14. Manual for computing bed load transport using BAGS (Bedload Assessment for Gravel-bed Streams) Software

    Treesearch

    John Pitlick; Yantao Cui; Peter Wilcock

    2009-01-01

    This manual provides background information and instructions on the use of a spreadsheet-based program for Bedload Assessment in Gravel-bed Streams (BAGS). The program implements six bed load transport equations developed specifically for gravel-bed rivers. Transport capacities are calculated on the basis of field measurements of channel geometry, reach-average slope,...

  15. Storm-influenced deltaic deposits of the Middle Jurassic Gaikema Sandstone in a measured section on the northern Iniskin Peninsula, Cook Inlet basin, Alaska

    USGS Publications Warehouse

    Stanley, Richard G.; Helmold, Kenneth P.; LePain, David L.

    2015-01-01

    Middle Jurassic strata of the Gaikema Sandstone were deposited about 170 million years ago on a delta that was located on the western shoreline of the Cook Inlet basin (Detterman and Hartsock, 1966; LePain and others, 2011, 2013). The delta was built by swift, sediment-laden rivers that flowed southeastward from a mountainous volcanic terrane west of the Bruin Bay fault (fig. 6-1). Upon reaching the edge of the Jurassic sea, the rivers dumped abundant sand, gravel, and mud into a depocenter on the northern Iniskin Peninsula, about 240 km southwest of Anchorage (figs. 6-1, 6-2). This report provides a preliminary description and interpretation of a detailed, 34-m-thick measured section in the Gaikema Sandstone on the south shore of Chinitna Bay at latitude 59.816°N, longitude 153.168°W (figs. 6-1–6-3). The sandstone in this measured section exhibits hummocky cross lamination and other features suggestive of storm-influenced deposition on the shallow-marine, seaward margin of the Gaikema delta. Our field studies of the Gaikema Sandstone were conducted during 2013 and 2014 as part of a collaborative effort by the Alaska Division of Geological & Geophysical Surveys (DGGS), Alaska Division of Oil and Gas (DOG), and U.S. Geological Survey (USGS) to provide the public with reliable information on the geologic framework and petroleum resource potential of Cook Inlet basin (Gillis, 2013, 2014). Jurassic rocks in Cook Inlet, including the Gaikema Sandstone, are of economic interest because they could contain significant undiscovered petroleum resources (Bureau of Ocean Energy Management, 2011; Stanley and others, 2011a, 2011b, 2013a; LePain and others, 2013).

  16. Predictive modeling of CO2 sequestration in deep saline sandstone reservoirs: Impacts of geochemical kinetics

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Balashov, Victor N.; Guthrie, George D.; Hakala, J. Alexandra

    2013-03-01

    One idea for mitigating the increase in fossil-fuel generated CO{sub 2} in the atmosphere is to inject CO{sub 2} into subsurface saline sandstone reservoirs. To decide whether to try such sequestration at a globally significant scale will require the ability to predict the fate of injected CO{sub 2}. Thus, models are needed to predict the rates and extents of subsurface rock-water-gas interactions. Several reactive transport models for CO{sub 2} sequestration created in the last decade predicted sequestration in sandstone reservoirs of ~17 to ~90 kg CO{sub 2} m{sup -3|. To build confidence in such models, a baseline problem including rockmore » + water chemistry is proposed as the basis for future modeling so that both the models and the parameterizations can be compared systematically. In addition, a reactive diffusion model is used to investigate the fate of injected supercritical CO{sub 2} fluid in the proposed baseline reservoir + brine system. In the baseline problem, injected CO{sub 2} is redistributed from the supercritical (SC) free phase by dissolution into pore brine and by formation of carbonates in the sandstone. The numerical transport model incorporates a full kinetic description of mineral-water reactions under the assumption that transport is by diffusion only. Sensitivity tests were also run to understand which mineral kinetics reactions are important for CO{sub 2} trapping. The diffusion transport model shows that for the first ~20 years after CO{sub 2} diffusion initiates, CO{sub 2} is mostly consumed by dissolution into the brine to form CO{sub 2,aq} (solubility trapping). From 20-200 years, both solubility and mineral trapping are important as calcite precipitation is driven by dissolution of oligoclase. From 200 to 1000 years, mineral trapping is the most important sequestration mechanism, as smectite dissolves and calcite precipitates. Beyond 2000 years, most trapping is due to formation of aqueous HCO{sub 3}{sup -}. Ninety-seven percent of

  17. Bed bug aggregation pheromone finally identified.

    PubMed

    Gries, Regine; Britton, Robert; Holmes, Michael; Zhai, Huimin; Draper, Jason; Gries, Gerhard

    2015-01-19

    Bed bugs have become a global epidemic and current detection tools are poorly suited for routine surveillance. Despite intense research on bed bug aggregation behavior and the aggregation pheromone, which could be used as a chemical lure, the complete composition of this pheromone has thus far proven elusive. Here, we report that the bed bug aggregation pheromone comprises five volatile components (dimethyl disulfide, dimethyl trisulfide, (E)-2-hexenal, (E)-2-octenal, 2-hexanone), which attract bed bugs to safe shelters, and one less-volatile component (histamine), which causes their arrestment upon contact. In infested premises, a blend of all six components is highly effective at luring bed bugs into traps. The trapping of juvenile and adult bed bugs, with or without recent blood meals, provides strong evidence that this unique pheromone bait could become an effective and inexpensive tool for bed bug detection and potentially their control. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Bed Bugs and Schools

    EPA Pesticide Factsheets

    Bed bugs have long been a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. They are successful hitchhikers, and can move from an infested site to furniture, bedding, baggage, boxes, and clothing.

  19. Method for packing chromatographic beds

    DOEpatents

    Freeman, David H.; Angeles, Rosalie M.; Keller, Suzanne

    1991-01-01

    Column chromatography beds are packed through the application of static force. A slurry of the chromatography bed material and a non-viscous liquid is filled into the column plugged at one end, and allowed to settle. The column is transferred to a centrifuge, and centrifuged for a brief period of time to achieve a predetermined packing level, at a range generally of 100-5,000 gravities. Thereafter, the plug is removed, other fixtures may be secured, and the liquid is allowed to flow out through the bed. This results in an evenly packed bed, with no channeling or preferential flow characteristics.

  20. Broadening the interpretive framework of deepwater deposits: 3D characterization of outcrop scale bedforms within supercritical dominated slope deposits of the Fish Creek-Vallecito Basin, Late-Miocene Gulf of California

    NASA Astrophysics Data System (ADS)

    West, L. M.; Steel, R.; Olariu, C.

    2017-12-01

    Study of seafloor bathymetry, numerical and physical modeling, and direct observation of turbidity currents increasingly suggests that sediment gravity flows over moderately steep basin slopes commonly reach Froude supercritical states. However, interpretation of supercritical features in deepwater outcrops remains limited in both quantity and scope, leaving stratigraphic qualities of supercritical deposits poorly understood. Slope turbidites on along steep margins of the early Gulf of California are exposed in seismic scale outcrops of the Late Miocene Lycium Member in the Fish Creek-Vallecito Basin of south-central California where they build 100s m-thick slopes. Measured sections, bedding orientation, and facies descriptions collected both for strike- and dip-oriented sections are combined with photogrammetric to characterize selected bedforms in three-dimensions. Analysis shows upflow accreting stacks of 10s of beds into a variety of bedforms with wavelengths and widths tens to hundreds of meters in scale and heights of 5-15 m. Beds have low-angle sinusoidal to sigmoidal down dip geometries and lens or lobate strike geometries. Bedding facies are dominated by 5-50 cm thick, normally graded, laminated sandstones capped by 1-3 cm bioturbated muds. Sandstones transition into interbedded sandstones and silty mudstones or 1-2 m thick silty mudstones. In places, Present also are incisional, steeply dipping backsets of 0.5-3 m-thick boulder-rich, amalgamated, structureless sandtones with abundant soft sediment deformation. that can transition downflow into arching, thinning, normally-graded sandstones. These bedforms are interpreted here as large-scale, long-lived supercritical deposits that represent preserved antidune and possibly cyclic steps bedforms or as-yet undefined bedforms incorporating by not bound by hydraulic jumps. This characterization provides new understanding of the nature of supercritical deposits and an important framework criteria for recognizing

  1. The fracture strength and frictional strength of Weber Sandstone

    USGS Publications Warehouse

    Byerlee, J.D.

    1975-01-01

    The fracture strength and frictional strength of Weber Sandstone have been measured as a function of confining pressure and pore pressure. Both the fracture strength and the frictional strength obey the law of effective stress, that is, the strength is determined not by the confining pressure alone but by the difference between the confining pressure and the pore pressure. The fracture strength of the rock varies by as much as 20 per cent depending on the cement between the grains, but the frictional strength is independent of lithology. Over the range 0 2 kb, ??=0??5 + 0??6??n. This relationship also holds for other rocks such as gabbro, dunite, serpentinite, granite and limestone. ?? 1975.

  2. Field assessment of alternative bed-load transport estimators

    USGS Publications Warehouse

    Gaeuman, G.; Jacobson, R.B.

    2007-01-01

    Measurement of near-bed sediment velocities with acoustic Doppler current profilers (ADCPs) is an emerging approach for quantifying bed-load sediment fluxes in rivers. Previous investigations of the technique have relied on conventional physical bed-load sampling to provide reference transport information with which to validate the ADCP measurements. However, physical samples are subject to substantial errors, especially under field conditions in which surrogate methods are most needed. Comparisons between ADCP bed velocity measurements with bed-load transport rates estimated from bed-form migration rates in the lower Missouri River show a strong correlation between the two surrogate measures over a wide range of mild to moderately intense sediment transporting conditions. The correlation between the ADCP measurements and physical bed-load samples is comparatively poor, suggesting that physical bed-load sampling is ineffective for ground-truthing alternative techniques in large sand-bed rivers. Bed velocities measured in this study became more variable with increasing bed-form wavelength at higher shear stresses. Under these conditions, bed-form dimensions greatly exceed the region of the bed ensonified by the ADCP, and the magnitude of the acoustic measurements depends on instrument location with respect to bed-form crests and troughs. Alternative algorithms for estimating bed-load transport from paired longitudinal profiles of bed topography were evaluated. An algorithm based on the routing of local erosion and deposition volumes that eliminates the need to identify individual bed forms was found to give results similar to those of more conventional dune-tracking methods. This method is particularly useful in cases where complex bed-form morphology makes delineation of individual bed forms difficult. ?? 2007 ASCE.

  3. Coalbed methane resource potential and current prospects in Pennsylvania

    USGS Publications Warehouse

    Markowski, A.K.

    1998-01-01

    methane potential. Phase I of this study involved the entire Pennsylvanian coal-bearing interval of southwestern Pennsylvania. Phase II focused on a stratigraphic delineation and evaluation of Allegheny Group coal beds and associated sandstones. Several prospective coal beds and associated facies relationships with channel-fill sandstones were determined. Possible non-coal scenarios for coalbed methane include erosional contacts between coal beds and overlying channel-fill sandstones and areas of stacked channel-fill sandstones. Repetitive sequences of coal accumulation are stacked, commonly with shale interburden, and are also potential coalbed methane targets. Additional Pennsylvania Geological Survey drilling/coalbed methane sampling occurred in Armstrong, Beaver, Cambria, Greene, Lawrence, Somerset, and Washington Counties. Raw coalbed methane desorption data tables/graphical displays of gas contents versus depth, thickness, and time, and average composition and heating values from coal beds of the Allegheny Group to the Dunkard Group are available at the Pennsylvania Geological Survey. Further information on cross-sections, isopleth maps, isopach maps, raw drillhole data, and ownership issues can also be obtained from the same source.A mapping of the regional geology of the bituminous coal-bearing intervals in southwestern Pennsylvania reveal several prospective coal beds and associated facies relationships with channel-fill sandstones. Possible non-coal scenarios for coalbed methane include erosional contacts between coalbeds and overlying channel-fill sandstones and areas of stacked channel-fill sandstones. Repetitive sequences of coal accumulation are stacked, commonly with shale interburden. and are also potential coalbed methane targets.

  4. Field aided characterization of a sandstone reservoir: Arroyo Grande Oil Field, California, USA

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Antonellini, M.; Aydin, A.

    1995-08-01

    The Arroyo Grande Oil Field in Central California has been productive since 1905 from the miopliocene Edna member of the Pismo formation. The Edna member is a massive poorly consolidated sandstone unit with an average porosity of 0.2 and a permeability of 1000-5000 md; the producing levels are shallow, 100 to 500 m from the ground surface. Excellent surface exposures of the same formation along road cuts across the field and above the reservoir provide an opportunity to study reservoir rocks at the surface and to relate fracture and permeability distribution obtained from cores to folds and faults observed inmore » outcrops. We mapped in outcrops the major structures of the oil field and determine the statistical distribution and orientation of small faults (deformation bands) that have been observed both in cores and outcrop. The relation between deformation bands and major structures has also been characterized with detailed mapping. By using synthetic logs it is possible to determine the log signature of structural heterogeneities such as deformation bands in sandstone; these faults cause a neutron porosity drop respect to the host rock in the order of 1-4%. Image analysis has been used to determine the petrophysical properties of the sandstone in outcrop and in cores; permeability is three orders of magnitude lower in faults than in the host rock and capillary pressure is 1-2 orders of magnitude larger in faults than in the host rock. Faults with tens of meters offsets are associated with an high density of deformation bands (10 to 250 m{sup -1}) and with zones of cement precipitation up to 30 m from the fault. By combining well and field data, we propose a structural model for the oil field in which high angle reverse faults with localized deformation bands control the distribution of the hydrocarbons on the limb of a syncline, thereby explaining the seemingly unexpected direction of slope of the top surface of the reservoir which was inferred by well data

  5. In-bed tube bank for a fluidized-bed combustor

    DOEpatents

    Hemenway, Jr., Lloyd F.

    1990-01-01

    An in-bed tube bank (10) for a fluidized bed combustor. The tube bank (10) of the present invention comprises one or more fluid communicating boiler tubes (30) which define a plurality of selectively spaced boiler tube sections (32). The tube sections (32) are substantially parallel to one another and aligned in a common plane. The tube bank (10) further comprises support members (34) for joining adjacent tube sections (32), the support members (34) engaging and extending along a selected length of the tube sections (32) and spanning the preselected space therebetween.

  6. Anatomy of anomalously thick sandstone units in the Brent Delta of the northern North Sea

    NASA Astrophysics Data System (ADS)

    Wei, Xiaojie; Steel, Ronald J.; Ravnås, Rodmar; Jiang, Zaixing; Olariu, Cornel; Ma, Yinsheng

    2018-05-01

    Some potentially attractive reservoirs, containing anomalously thick (10s to a few 100 m), cross-stratified sandstone, have been locally encountered within both the classic regressive (lower Brent) and the transgressive (upper Brent) segments of the Brent Delta. Three documented cases of these sandstone bodies are re-examined. They are internally dominated by simple or compound dunes, and typified by two types of deepening-upward succession, recording a retrogradational or transgressive shoreline history. Type I is expressed as a single estuarine succession changing upwards from erosive, coarse-grained channelized deposits into outer estuary tidal bar deposits. The estuary is underlain and overlain by deltaic deposits. Type II lacks significant basal river deposits but is composed by stacked mixed-energy and tide-dominated estuarine deposits. It is underlain by deltaic deposits and overlain by open marine sediments. Considering the structural evolution in the northern North Sea basin, we suggest (as did some earlier researchers) that these sandstone bodies were local, but sometimes broad transgressive estuaries, formed at any time during large-scale Brent Delta growth and decay. The estuary generation was likely triggered by fluvial incision coupled with active faulting, producing variable accommodation embayments, where tidal currents became focused and deposition became transgressive. The spatial variations of the interpreted estuary deposits were linked with variable, fault-generated accommodation. The relatively simple, lower Brent estuarine units were created by short-lived, fault activity in places, whereas the complex, stacked upper-Brent estuarine units were likely a result of more long-lived, punctuated fault-induced subsidence leading into the northern North Sea main rifting stage. The thick cross-stratified units potentially accumulated in the hangingwall of large bounding faults.

  7. Discordant K-Ar and Young Exposure Dates for the Windjana Sandstone, Kimberley, Gale Crater, Mars

    NASA Technical Reports Server (NTRS)

    Vasconcelos, P. M.; Farley, K. A.; Malespin, C. A.; Mahaffy, P.; Ming, D.; McLennan, S. M.; Hurowitz, J. A.; Rice, Melissa S.

    2016-01-01

    K-Ar and noble gas surface exposure age measurements were carried out on the Windjana sandstone, Kimberley region, Gale Crater, Mars, by using the Sample Analysis at Mars instrument on the Curiosity rover. The sandstone is unusually rich in sanidine, as determined by CheMin X-ray diffraction, contributing to the high K2O concentration of 3.09 +/- 0.20 wt % measured by Alpha-Particle X-ray Spectrometer analysis. A sandstone aliquot heated to approximately 915 C yielded a K-Ar age of 627 +/- 50 Ma. Reheating this aliquot yielded no additional Ar. A second aliquot heated in the same way yielded a much higher K-Ar age of 1710 +/- 110 Ma. These data suggest incomplete Ar extraction from a rock with a K-Ar age older than 1710 Ma. Incomplete extraction at approximately 900 C is not surprising for a rock with a large fraction of K carried by Ar-retentive K-feldspar. Likely, variability in the exact temperature achieved by the sample from run to run, uncertainties in sample mass estimation, and possible mineral fractionation during transport and storage prior to analysis may contribute to these discrepant data. Cosmic ray exposure ages from He-3 and Ne-21 in the two aliquots are minimum values given the possibility of incomplete extraction. However, the general similarity between the He-3 (57 +/- 49 and 18 +/- 32 Ma, mean 30 Ma) and Ne-21 (2 +/- 32 and 83 +/- 24 Ma, mean 54 Ma) exposure ages provides no evidence for underextraction. The implied erosion rate at the Kimberley location is similar to that reported at the nearby Yellowknife Bay outcrop.

  8. Development of deformation band clusters in porous quartz sandstones - Contribution from microstructural analysis and numerical modeling

    NASA Astrophysics Data System (ADS)

    Philit, S.; Soliva, R.; Chemenda, A. I.

    2017-12-01

    Because sandstones form good reservoirs for hydrocarbon, water or C02 storage, the understanding of the deformation processes in sandstones is major. The deformation band clusters result from the localization of the deformation in porous sandstones under the form of gathered low-permeability cataclastic deformation bands. It has recently been shown that this localization is favored in extensional tectonics. The clusters measure tens to hundreds of meters in extent and propagate vertically as long as the sandstone is clean. Because the clusters can form several kilometers long networks, they are likely to hamper fluid flow during reservoir exploitation. Yet, the processes of band accumulation linked to the evolution of the clusters to a potential faulting are poorly understood. An integrated study coupling a microscopic analysis of the deformed granular material in clusters from 7 sites in the world and distinct element numerical modeling permits to propose a model for cluster growth. Our microscopic analysis reveals that the clusters display varying degree of cataclasis, with the most important degrees in the bands. This cataclasis is accompanied by porosity reduction (more reduced in thrust Andersonian regime), and increased Particle Size Distribution. This testifies of an important packing and implies an increased number of particle coordination. During deformation, the grain shape is both smoothened and roughened; the averaged values of the roundness and circularity indicate a rapid roughening of the clasts at the first stages of deformation followed by a slight smoothening. The roughening of the clasts in densely packed material induces high friction and strengthens the material. High residual porosity at some band edges suggests a local dilatant behavior of sheared material. Our distinct element numerical models and other particle models in the literature confirm this observation. The development of force chains with low particle coordination at these

  9. Natural Erosion of Sandstone as Shape Optimisation.

    PubMed

    Ostanin, Igor; Safonov, Alexander; Oseledets, Ivan

    2017-12-11

    Natural arches, pillars and other exotic sandstone formations have always been attracting attention for their unusual shapes and amazing mechanical balance that leave a strong impression of intelligent design rather than the result of a stochastic process. It has been recently demonstrated that these shapes could have been the result of the negative feedback between stress and erosion that originates in fundamental laws of friction between the rock's constituent particles. Here we present a deeper analysis of this idea and bridge it with the approaches utilized in shape and topology optimisation. It appears that the processes of natural erosion, driven by stochastic surface forces and Mohr-Coulomb law of dry friction, can be viewed within the framework of local optimisation for minimum elastic strain energy. Our hypothesis is confirmed by numerical simulations of the erosion using the topological-shape optimisation model. Our work contributes to a better understanding of stochastic erosion and feasible landscape formations that could be found on Earth and beyond.

  10. Apparatus and process for controlling fluidized beds

    DOEpatents

    Rehmat, Amirali G.; Patel, Jitendra G.

    1985-10-01

    An apparatus and process for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance.

  11. Fluidized bed boiler feed system

    DOEpatents

    Jones, Brian C.

    1981-01-01

    A fluidized bed boiler feed system for the combustion of pulverized coal. Coal is first screened to separate large from small particles. Large particles of coal are fed directly to the top of the fluidized bed while fine particles are first mixed with recycled char, preheated, and then fed into the interior of the fluidized bed to promote char burnout and to avoid elutriation and carryover.

  12. Petroleum system and production characteristics of the Muddy (J) Sandstone (Lower Cretaceous) Wattenberg continuous gas field, Denver basin, Colorado

    USGS Publications Warehouse

    Higley, D.K.; Cox, D.O.; Weimer, R.J.

    2003-01-01

    Wattenberg field is a continuous-type gas accumulation. Estimated ultimate recovery from current wells is 1.27 tcf of gas from the Lower Cretaceous Muddy (J) Sandstone. Mean gas resources that have the potential to be added to these reserves in the next 30 yr are 1.09 tcf; this will be primarily through infill drilling to recover a greater percentage of gas in place and to drain areas that are isolated because of geologic compartmentalization. Greatest gas production from the Muddy (J) Sandstone in Wattenberg field occurs (1) from within the most permeable and thickest intervals of Fort Collins Member delta-front and nearshore-marine sandstones, (2) to a lesser extent from the Horsetooth Member valley-fill channel sandstones, (3) in association with a large thermal anomaly that is delineated by measured temperatures in wells and by vitrinite reflectance contours of 0.9% and greater, (4) in proximity to the bounding Mowry, Graneros, and Skull Creek shales that are the hydrocarbon source rocks and reservoir seals, and (5) between the Lafayette and Longmont right-lateral wrench fault zones (WFZs) with secondary faults that act as conduits in areas of the field. The axis of greatest gas production is north 25 to 35?? northeast, which parallels the basin axis. Recurrent movement along five right-lateral WFZs that crosscut Wattenberg field shifted the Denver basin axis to the northeast and influenced depositional and erosional patterns of the reservoir and seal intervals. Levels of thermal maturity within the Wattenberg field are anomalously high compared to other areas of the Denver basin. The Wattenberg field thermal anomaly may be due to upward movement of fluids along faults associated with probable igneous intrusions. Areas of anomalous high heat flow within the field correlate with an increased and variable gas-oil ratio.

  13. Fault evolution in volcanic tuffs and quartz-rich eolian sandstone as mechanical analogs for faulting in Martian pyroclastic deposits

    NASA Astrophysics Data System (ADS)

    Okubo, C. H.

    2014-12-01

    In order to establish a foundation for studies of faulting in Martian rocks and soils in volcanic terrain, the distribution of brittle strain around faults within the North Menan Butte Tuff in the eastern Snake River Plain, Idaho and the Joe Lott Tuff Member of the Mount Belknap Volcanics, Utah, has been recently described. These studies employed a combination of macroscopic and microscopic observations, including measurements of in situ permeability as a proxy for non-localized brittle deformation of the host rock. In areas where the tuff retained its primary granular nature at the time of deformation, initial plastic yielding in both tuffs occurred along deformation bands. Both compactional and dilational types of deformation bands were observed, and faulting occurred along clusters of deformation bands. Where secondary alteration processes imparted a massive texture to the tuff, brittle deformation was accommodated along fractures. Host-rock permeability exhibits little variation from non-deformed values in the North Menan Butte Tuff, whereas host rock permeability is reduced by roughly an order of magnitude through compaction alone (no alteration) in the Joe Lott Tuff. To create a bridge between these observations in tuff and the more substantial body of work centered on deformation band formation and faulting in quartz-rich sandstones, the same techniques employed in the North Menan Butte Tuff and the Joe Lott Tuff have also been applied to a kilometer-scale fault in the Jurassic Navajo Sandstone in the Waterpocket Fold, Utah. These observations demonstrate that the manifestation of strain and evolution of faulting in the Mars-analog tuffs are comparable to that in quartz-rich sandstones. Therefore, current understanding of brittle deformation in quartz-rich sandstones can be used to inform investigations into fault growth within porous tuffs on Mars. A discussion of these observations, practical limitations, and directions for future work are presented here.

  14. Bed material agglomeration during fluidized bed combustion. Technical progress report, 1 July, 1993--30 September, 1993

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brown, R.C.; Dawson, M.R.; Noble, S.D.

    Agglomerates formed in laboratory coal combustion tests were analyzed to determine the chemical and mineral reactions which lead to the cohesion of bed particles. Combustion tests were conducted at 75, 90, 100, and 120% theoretical air values. The test at 75% theoretical air resulted in the formation of bed agglomerates within 30 minutes. Agglomerates which formed at the lower theoretical air values were compared to unagglomerated bed samples by X-ray diffraction analyses. Polished thin sections of the agglomerates were made for optical and scanning electron microscopy. The results of these analyses indicate there were, in a broad sense, two typesmore » of mineralogic reactions which lead to the cohesion of bed particles in the agglomerates. One mechanism of cohesion resulted from the melting of bed particles to form a viscous material which bridged other bed particles. Based on the chemical composition of the glass (which resulted from the melt), this material was probably derived from aluminosilicate minerals in the sand bed or from clays within the coal. Because of the high iron content in these glasses (4 to 5 wt%), it is likely that iron pyrites in the coal were involved in fluxing reactions. In addition, MgO appears to be relatively high in the glasses. It is suspected that Ca-Mg carbonates (dolomite) from the bed sand are also involved in mineralogic reactions with the aluminosilicate melt. The second type of mineralogic reaction appears to be a reaction involving calcium and magnesium with other bed particles and with the aluminosilicate melt to form new mineral phases. Although the composition of these phases is somewhat variable, some resemble single-chain silicates or pyroxenes.« less

  15. Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Connolly, J.R.; Keil, K.; Mansker, W.L.

    1984-10-01

    This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworkedmore » zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain.« less

  16. Assessment of undiscovered sandstone copper deposits of the Kodar-Udokan area, Russia: Chapter M in Global mineral resource assessment

    USGS Publications Warehouse

    Zientek, Michael L.; Chechetkin, Vladimir S.; Parks, Heather L.; Box, Stephen E.; Briggs, Deborah A.; Cossette, Pamela M.; Dolgopolova, Alla; Hayes, Timothy S.; Seltmann, Reimar; Syusyura, Boris; Taylor, Cliff D.; Wintzer, Niki E.

    2014-01-01

    This probabilistic assessment indicates that a significant amount of undiscovered copper is associated with sediment-hosted stratabound copper deposits in the Kodar-Udokan Trough. In the assessment, a mean of 21 undiscovered deposits is estimated to occur within the Kodar-Udokan area. There are two known deposits in the area that contain drill-identified resources of 19.6 million metric tons of copper. Using Monte Carlo simulation, probabilistic estimates of the numbers of undiscovered sandstone copper deposits for these tracts were combined with tonnage and grade distributions of sandstone copper deposits to forecast an arithmetic mean of 20.6 million metric tons of undiscovered copper. Significant value can be expected from associated metals, particularly silver.

  17. Mineralogical Characterization of Navajo Sandstone Iron Oxide Concretions Using QEMSCAN and Reflectance Spectroscopy; Analogue for Martian Diagenetic Processes

    NASA Astrophysics Data System (ADS)

    Potter, S. L.; Chan, M. A.; Petersen, E. U.

    2008-03-01

    The Navajo Sandstone concretions were evaluated to detect mineralogical changes and chemical gradients. Sequential relationships suggest an evolution of phases of cements. The Mars "blueberries" may have a similar evolution of cements.

  18. Hydrology of the Ferron sandstone aquifer and effects of proposed surface-coal mining in Castle Valley, Utah, with sections on stratigraphy and leaching of overburden

    USGS Publications Warehouse

    Lines, Gregory C.; Morrissey, Daniel J.; Ryer, Thomas A.; Fuller, Richard H.

    1983-01-01

    Coal in the Ferron Sandstone Member of the Mancos Shale of Cretaceous age has traditionally been mined by underground techniques in the Emery Coal Field in the southern end of Castle Valley in east-central Utah. However, approximately 99 million tons are recoverable by surface mining. Ground water in the Ferron is the sole source of supply for the town of Emery, but the aquifer is essentially untapped outside the Emery area.The Ferron Sandstone Member crops out along the eastern edge of Castle Valley and generally dips 2 ? to 10 ? to the northwest. Sandstones in the Ferron are enclosed between relatively impermeable shale in the Tununk and Blue Gate Members of the Mancos Shale. Along the outcrop, the Ferron ranges in thickness from about 80 feet in the northern part of Castle Valley to 850 feet in the southern part. The Ferron also generally thickens in the subsurface downdip from the outcrop. Records from wells and test holes indicate that the full thickness of the Ferron is saturated with water in most areas downdip from the outcrop area.Tests in the Emery area indicate that transmissivity of the Ferron sandstone aquifer ranges from about 200 to 700 feet squared per day where the Ferron is fully saturated. Aquifer transmissivity is greatest near the Paradise Valley-Joes Valley fault system where permeability has been increased by fracturing. Storage coefficient ranges from about 10 .6 to 10 -3 where the Ferron sandstone aquifer is confined and probably averages 5 x 10-2 where it is unconfined.

  19. Low shear stress gravel-bed river

    USGS Publications Warehouse

    Milhous, Robert T.

    1997-01-01

    A low stress gravel bed river is a river where the cross-sectional average dimensionless shear stress (??*) rarely exceeds 0.047. That is the case for the Gunnison River below Delta in Western Colorado. The cross-sectional average ??* in the Gunnison River has not exceeded 0.047, except at one cross section during one year, in the 87 years of record. A ??* of 0.047 is the critical ??* in the bed-load equation considered to be most applicable to gravel/cobble bed rivers (the Meyer-Peter, Mueller equation). According to this equation, there has been no bed-material movement in the Gunnison River since 1920; in fact there has been bed-material movement and this movement is biologically important. Bed-material is moved when the ??* is 0.016 or larger. Streamflows that cause a ??* of at least 0.016 maintain the aquatic habitat in a low shear stress river.

  20. Geohydrologic reconnaissance of the Avoca lignite deposit area near Williston, northwestern North Dakota

    USGS Publications Warehouse

    Horak, W.F.; Crosby, O.A.

    1985-01-01

    The Avoca lignite deposit in the Sentinel Butte Member of the Fort Union Formation consists of four potentially strippable lignite beds. Average bed thicknesses, in descending order, are 5, 5, 9, and 8 .feet. In the area between Stony Creek and Crazy Man Coulee, the lignite beds are unsaturated, and between Stony Creek and Little Muddy River, only the two lowest beds are saturated. Natural discharge to outcrops in the stream valleys results in low potentiometric levels in the lignite beds.Aquifers in sandstone beds in the Fox Hills Sandstone and the Hell Creek Formation probably would yield as much as 50 gallons per minute of sodium bicarbonate type water. Dissolved-solids concentrations range from 800 to 2,000 milligrams per liter. The aquifers are from 1,100 to 1,800 feet below land surface. Sandstone beds in the Ludlow and Cannonball Members of the Fort Union Formation probably could yield several gallons per minute of sodium bicarbonate water with dissolved-solids concentrations ranging from 800 to 2,000 milligrams per liter. Aquifers in the Ludlow and Cannonball Members lie between 700 and 1,300 feet below land surface. Individual sand beds in the Tongue River and Sentinel Butte Members of the Fort Union Formation are the shallowest aquifers encountered below the minable lignite beds. Properly constructed wells completed in these sand beds could yield as much as 40 gallons per minute. The water generally is a sodium bicarbonate type with dissolved-solids concentrations ranging from about 500 to 4,200 milligrams per liter. Alluvium and glacial-drift deposits constitute the Little Muddy aquifer bordering the lignite deposit on the west and south. The aquifer could yield as much as 1,200 gallons per minute of sodium bicarbonate type water with dissolved-solids concentrations ranging from 975 to 1, 730 milligrams per liter.Little Muddy Creek and Stony Creek have significant base flow. The flow is contributed partly by discharge from the lignite. Quality of water

  1. Numerical simulation of turbulence and sand-bed morphodynamics in natural waterways under live bed conditions

    NASA Astrophysics Data System (ADS)

    Khosronejad, Ali; Sotiropoulos, Fotis

    2012-11-01

    We develop and validate a 3D numerical model for coupled simulations of turbulence and sand-bed morphodynamics in natural waterways under live bed conditions. We employ the Fluid-Structure Interaction Curvilinear Immersed Boundary (FSI-CURVIB) method of Khosronejad et al. (Adv. in Water Res., 2011). The mobile channel bed is discretized with an unstructured triangular grid and treated as the sharp-interface immersed boundary embedded in a background curvilinear mesh. Transport of bed load and suspended load sediments are combined in the non-equilibrium from of the Exner-Poyla for the bed surface elevation, which evolves due to the spatio-temporally varying bed shear stress and velocity vector induced by the turbulent flow field. Both URANS and LES models are implemented to simulate the effects of turbulence. Simulations are carried out for a wide range of waterways, from small scale streams to large-scale rivers, and the simulated sand-waves are quantitatively compared to available measurements. It is shown that the model can accurately capture sand-wave formation, growth, and migration processes observed in nature. The simulated bed-forms are found to have amplitude and wave length scales ranging from the order of centimeters up to several meters. This work was supported by NSF Grants EAR-0120914 and EAR-0738726, and National Cooperative Highway Research Program Grant NCHRP-HR 24-33. Computational resources were provided by the University of Minnesota Supercomputing Institute.

  2. Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

    NASA Astrophysics Data System (ADS)

    Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

    2010-05-01

    The injection of CO2 into deep saline aquifers is the most promising strategy for the reduction of CO2 emissions to the atmosphere via long-term geological storage. The study is part of the CO2SINK project conducted at Ketzin, situated 40 km west of Berlin. There, food grade CO2 has been pumped into the Upper Triassic Stuttgart Formation since June 2008. The main objective of the experimental program is to investigate the effects of long-term CO2 exposure on the physico-chemical properties of the reservoir rock. To achieve this goal, core samples from observation well Ktzi 202 have been saturated with synthetic brine and exposed to CO2 in high quality steel autoclaves at simulated reservoir P-T-conditions of 5.5 MPa and 40 ° C. The synthetic brine had a composition representative of the formation fluid (Förster et al., 2006) of 172.8 g/l NaCl, 8.0 g/l MgCl2×2H2O, 4.8 g/l CaCl2×2H2O and 0.6 g/l KCl. After 15 months, the first set of CO2-exposed samples was removed from the pressure vessels. Thin sections, XRD, SEM as well as EMP data were used to determine the mineralogical features of the reservoir rocks before and after the experiments. Additionally, NMR relaxation and MP was performed to measure poroperm and pore size distribution values of the twin samples. The analyzed samples are fine- to medium grained, moderately well- to well sorted and weakly consolidated sandstones. Quartz and plagioclase are the major components, while K-feldspar, hematite, white & dark mica, chlorite and illite are present in minor and varying amounts. Cements are composed of analcime, dolomite and anhydrite. Some samples show mm- to cm-scale cross-beddings. The laminae comprise lighter, quartz- and feldspar-dominated layers and dark-brownish layers with notably less quartz and feldspars. The results are consistent with those of Blaschke et al. (2008). The plagioclase composition indicates preferred dissolution of the Ca-component and a trend toward albite-rich phases or even pure

  3. Bacterial communities in pigmented biofilms formed on the sandstone bas-relief walls of the Bayon Temple, Angkor Thom, Cambodia.

    PubMed

    Kusumi, Asako; Li, Xianshu; Osuga, Yu; Kawashima, Arata; Gu, Ji-Dong; Nasu, Masao; Katayama, Yoko

    2013-01-01

    The Bayon temple in Angkor Thom, Cambodia has shown serious deterioration and is subject to the formation of various pigmented biofilms. Because biofilms are damaging the bas-reliefs, low reliefs engraved on the surface of sandstone, information about the microbial community within them is indispensable to control biofilm colonization. PCR-denaturing gradient gel electrophoresis (DGGE) analysis of biofilm samples from the pigmented sandstone surfaces showed that the bacterial community members in the biofilms differed clearly from those in the air and had low sequence similarity to database sequences. Non-destructive sampling of biofilm revealed novel bacterial groups of predominantly Rubrobacter in salmon pink biofilm, Cyanobacteria in chrome green biofilm, Cyanobacteria and Chloroflexi in signal violet biofilm, Chloroflexi in black gray biofilm, and Deinococcus-Thermus, Cyanobacteria, and Rubrobacter in blue green biofilm. Serial peeling-off of a thick biofilm by layers with adhesive sheets revealed a stratified structure: the blue-green biofilm, around which there was serious deterioration, was very rich in Cyanobacteria near the surface and Chloroflexi in deep layer below. Nitrate ion concentrations were high in the blue-green biofilm. The characteristic distribution of bacteria at different biofilm depths provides valuable information on not only the biofilm formation process but also the sandstone weathering process in the tropics.

  4. Determination of Hydraulic and Transport Parameters of Organic Chemical and Inorganic Anions Solutes for Unfractured Cores of Berea Sandstone Using a Hydraulic Coreholder

    NASA Astrophysics Data System (ADS)

    Blanford, W. J.; Neil, L.

    2017-12-01

    To better evaluate the potential for toxic organic chemicals to migrate upward through the rock strata from hydraulic fracturing zones and into groundwater resources, a series of miscible displacement solute transport studies of cores of Berea Sandstone have been conducted using hydrostatic core holder. These tests involved passing aqueous solutions with natural background level of salts using a high pressure LC pump through 2 in wide by 3 in long unfractured cores held within the holder. Relative solute transport of 100 to 500ml pulses of target solutes including a series of chlorinated solvents and methylated benzenes was measured through in-line UV and fluorescence detectors and manual sampling and analysis with GCMS. The results found these sandstones to result in smooth ideal shaped breakthrough curves. Analysis with 1D transport models (CXTFIT) of the results found strong correlation with chemical parameters (diffusion coefficients, aqueous solubility, and octanol-water partitioning coefficients) showing that these parameter and QSPR relationships can be used to make accurate predictions for such a system. In addition to the results of the studies, lessons learned from this novel use of a coreholder for evaluation of porosity, water-saturated permeability, and solute transport of these sandstones (K = 1.5cm/day) and far less permeable sandstones samples (K = 0.15 cm/yr) from a hydraulic fracturing site in central Pennsylvania will be presented.

  5. Solids feed nozzle for fluidized bed

    DOEpatents

    Zielinski, Edward A.

    1982-01-01

    The vertical fuel pipe of a fluidized bed extends up through the perforated support structure of the bed to discharge granulated solid fuel into the expanded bed. A cap, as a deflecting structure, is supported above the discharge of the fuel pipe and is shaped and arranged to divert the carrier fluid and granulated fuel into the combusting bed. The diverter structure is spaced above the end of the fuel pipe and provided with a configuration on its underside to form a venturi section which generates a low pressure in the stream into which the granules of solid fuel are drawn to lengthen their residence time in the combustion zone of the bed adjacent the fuel pipe.

  6. Predicting fractional bed load transport rates: Application of the Wilcock‐Crowe equations to a regulated gravel bed river

    USGS Publications Warehouse

    Gaeuman, David; Andrews, E.D.; Krause, Andreas; Smith, Wes

    2009-01-01

    Bed load samples from four locations in the Trinity River of northern California are analyzed to evaluate the performance of the Wilcock‐Crowe bed load transport equations for predicting fractional bed load transport rates. Bed surface particles become smaller and the fraction of sand on the bed increases with distance downstream from Lewiston Dam. The dimensionless reference shear stress for the mean bed particle size (τ*rm) is largest near the dam, but varies relatively little between the more downstream locations. The relation between τ*rm and the reference shear stresses for other size fractions is constant across all locations. Total bed load transport rates predicted with the Wilcock‐Crowe equations are within a factor of 2 of sampled transport rates for 68% of all samples. The Wilcock‐Crowe equations nonetheless consistently under‐predict the transport of particles larger than 128 mm, frequently by more than an order of magnitude. Accurate prediction of the transport rates of the largest particles is important for models in which the evolution of the surface grain size distribution determines subsequent bed load transport rates. Values of τ*rm estimated from bed load samples are up to 50% larger than those predicted with the Wilcock‐Crowe equations, and sampled bed load transport approximates equal mobility across a wider range of grain sizes than is implied by the equations. Modifications to the Wilcock‐Crowe equation for determining τ*rm and the hiding function used to scale τ*rm to other grain size fractions are proposed to achieve the best fit to observed bed load transport in the Trinity River.

  7. Sedimentological characterization of flood-tidal delta deposits in the Sego Sandstone, subsidence analysis in the Piceance Creek Basin, and uranium-lead geochronology (NW Colorado, USA)

    NASA Astrophysics Data System (ADS)

    York, Carly C.

    The Sego Sandstone located in western Colorado is a member of the Upper Cretaceous Mesaverde Group and is considered an analogue of the Canadian heavy oil sands. Deposition of the Sego Sandstone occurred during the Upper Campanian (~78 Ma) at the end of the Sevier Orogeny and the beginning of the Laramide Orogeny on the western edge of the Cretaceous Interior Seaway. Although regional studies have detailed time equivalent deposits in the Book Cliffs, UT, the tidally influenced and marginal marine lithofacies observed north of Rangely, CO are distinctly different from the dominately fluvial and tidally-influenced delta facies of Book Cliff outcrops to the southwest. This study characterized flood-tidal delta deposits within the Sego Sandstone, the subsidence history of the Upper Cretaceous sedimentary rocks within the present day Piceance Creek Basin in NW Colorado, and the detrital zircon signal and oldest depositional age of the Sego Sandstone. The goals of this study are to (i) identify relative controls on reservoir characteristics of marginal marine deposits, specifically in flood-tidal delta deposits; (ii) identify the possible mechanisms responsible for subsidence within the present day Piceance Creek Basin during the Late Cretaceous; and (iii) better constrain the provenance and maximum depositional age of the Sego Sandstone. In this study I compared grain size diameter, grain and cement composition, and the ratio of pore space/cement from thin sections collected in tidal, shoreface, and flood-tidal delta facies recognized along detailed measured stratigraphic sections. This analysis provides a detailed comparison between different depositional environments and resultant data showed that grain size diameter is different between tidal, shoreface, and flood-tidal delta facies. Identifying the subsidence mechanisms affecting the Piceance Creek Basin and sediment source of the Late Cretaceous sediments, on the other hand, is important for evaluation of controls

  8. Bed Bug Infestations in an Urban Environment

    PubMed Central

    Svoboda, Tomislav J.; De Jong, Iain J.; Kabasele, Karl J.; Gogosis, Evie

    2005-01-01

    Until recently, bed bugs have been considered uncommon in the industrialized world. This study determined the extent of reemerging bed bug infestations in homeless shelters and other locations in Toronto, Canada. Toronto Public Health documented complaints of bed bug infestations from 46 locations in 2003, most commonly apartments (63%), shelters (15%), and rooming houses (11%). Pest control operators in Toronto (N = 34) reported treating bed bug infestations at 847 locations in 2003, most commonly single-family dwellings (70%), apartments (18%), and shelters (8%). Bed bug infestations were reported at 20 (31%) of 65 homeless shelters. At 1 affected shelter, 4% of residents reported having bed bug bites. Bed bug infestations can have an adverse effect on health and quality of life in the general population, particularly among homeless persons living in shelters. PMID:15829190

  9. DNA profiling of trace DNA recovered from bedding.

    PubMed

    Petricevic, Susan F; Bright, Jo-Anne; Cockerton, Sarah L

    2006-05-25

    Trace DNA is often detected on handled items and worn clothing examined in forensic laboratories. In this study, the potential transfer of trace DNA to bedding by normal contact, when an individual sleeps in a bed, is examined. Volunteers slept one night on a new, lower bed sheet in their own bed and one night in a bed foreign to them. Samples from the sheets were collected and analysed by DNA profiling. The results indicate that the DNA profile of an individual can be obtained from bedding after one night of sleeping in a bed. The DNA profile of the owner of the bed could also be detected in the foreign bed experiments. Since mixed DNA profiles can be obtained from trace DNA on bedding, caution should be exercised when drawing conclusions from DNA profiling results obtained from such samples. This transfer may have important repercussions in sexual assault investigations.

  10. Identification of sandstone core damage using scanning electron microscopy

    NASA Astrophysics Data System (ADS)

    Ismail, Abdul Razak; Jaafar, Mohd Zaidi; Sulaiman, Wan Rosli Wan; Ismail, Issham; Shiunn, Ng Yinn

    2017-12-01

    Particles and fluids invasion into the pore spaces causes serious damage to the formation, resulting reduction in petroleum production. In order to prevent permeability damage for a well effectively, the damage mechanisms should be identified. In this study, water-based drilling fluid was compared to oil-based drilling fluids based on microscopic observation. The cores were damaged by several drilling fluid systems. Scanning electron microscope (SEM) was used to observe the damage mechanism caused by the drilling fluids. Results showed that the ester based drilling fluid system caused the most serious damage followed by synthetic oil based system and KCI-polymer system. Fine solids and filtrate migration and emulsion blockage are believed to be the major mechanisms controlling the changes in flow properties for the sandstone samples.

  11. Assessment of potential shale oil and tight sandstone gas resources of the Assam, Bombay, Cauvery, and Krishna-Godavari Provinces, India, 2013

    USGS Publications Warehouse

    Klett, Timothy R.; Schenk, Christopher J.; Wandrey, Craig J.; Brownfield, Michael E.; Charpentier, Ronald R.; Tennyson, Marilyn E.; Gautier, Donald L.

    2014-01-01

    Using a well performance-based geologic assessment methodology, the U.S. Geological Survey estimated a technically recoverable mean volume of 62 million barrels of oil in shale oil reservoirs, and more than 3,700 billion cubic feet of gas in tight sandstone gas reservoirs in the Bombay and Krishna-Godavari Provinces of India. The term “provinces” refer to geologically defined units assessed by the USGS for the purposes of this report and carries no political or diplomatic connotation. Shale oil and tight sandstone gas reservoirs were evaluated in the Assam and Cauvery Provinces, but these reservoirs were not quantitatively assessed.

  12. 21 CFR 892.1350 - Nuclear scanning bed.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

  13. 21 CFR 892.1350 - Nuclear scanning bed.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

  14. 21 CFR 892.1350 - Nuclear scanning bed.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

  15. 21 CFR 892.1350 - Nuclear scanning bed.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

  16. 21 CFR 892.1350 - Nuclear scanning bed.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Nuclear scanning bed. 892.1350 Section 892.1350...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1350 Nuclear scanning bed. (a) Identification. A nuclear scanning bed is an adjustable bed intended to support a patient during a nuclear medicine...

  17. Water produced with coal-bed methane

    USGS Publications Warehouse

    ,

    2000-01-01

    Natural gas produced from coal beds (coal-bed methane, CBM) accounts for about 7.5 percent of the total natural gas production in the United States. Along with this gas, water is also brought to the surface. The amount of water produced from most CBM wells is relatively high compared to conventional natural gas wells because coal beds contain many fractures and pores that can contain and transmit large volumes of water. In some areas, coal beds may function as regional or local aquifers and important sources for ground water. The water in coal beds contributes to pressure in the reservoir that keeps methane gas adsorbed to the surface of the coal. This water must be removed by pumping in order to lower the pressure in the reservoir and stimulate desorption of methane from the coal (fi g. 1). Over time, volumes of pumped water typically decrease and the production of gas increases as coal beds near the well bore are dewatered.

  18. Improved reservoir characterization of the Rose Run sandstone on the East Randolph Field, Portage County, Ohio

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Safley, I.E.; Thomas, J.B.

    1996-09-01

    The East Randolph Field, located in Randolph Township, Portage County, Ohio, produces oil and gas from the Cambrian Rose Run sandstone unit, a member of the Knox Supergroup. Field development and infill drilling opportunities illustrate the need for improved reservoir characterization of the hydrocarbon productive intervals. This reservoir study is conducted under the Department of Energy`s Reservoir Management Program with professionals from BDM-Oklahoma and Belden & Blake Corporation. Well log and core analyses were conducted to determine the reservoir distribution, the heterogeneity of the hydrocarbon producing intervals, and the effects of faulting and fracturing on well productivity. The Rose Runmore » sandstones and interbedded dolomites were subdivided into three productive intervals. Cross sections were constructed for correlation of individual layers and identification of localized faulting. The geologic data was input into GeoGraphix software for construction of structure, net pay, production, and gas- and water-oil ratio maps.« less

  19. Bed Load Variability and Morphology of Gravel Bed Rivers Subject to Unsteady Flow: A Laboratory Investigation

    NASA Astrophysics Data System (ADS)

    Redolfi, M.; Bertoldi, W.; Tubino, M.; Welber, M.

    2018-02-01

    Measurement and estimation of bed load transport in gravel bed rivers are highly affected by its temporal fluctuations. Such variability is primarily driven by the flow regime but is also associated with a variety of inherent channel processes, such as flow turbulence, grain entrainment, and bed forms migration. These internal and external controls often act at comparable time scales, and are therefore difficult to disentangle, thus hindering the study of bed load variability under unsteady flow regime. In this paper, we report on laboratory experiments performed in a large, mobile bed flume where typical hydromorphological conditions of gravel bed rivers were reproduced. Data from a large number of replicated runs, including triangular and square-wave hydrographs, were used to build a statistically sound description of sediment transport processes. We found that the inherent variability of bed load flux strongly depends on the sampling interval, and it is significantly higher in complex, wandering or braided channels. This variability can be filtered out by computing the mean response over the experimental replicates, which allows us to highlight two distinctive phenomena: (i) an overshooting (undershooting) response of the mean bed load flux to a sudden increase (decrease) of discharge, and (ii) a clockwise hysteresis in the sediment rating curve. We then provide an interpretation of these findings through a conceptual mathematical model, showing how both phenomena are associated with a lagging morphological adaptation to unsteady flow. Overall, this work provides basic information for evaluating, monitoring, and managing gravel transport in morphologically active rivers.

  20. Pore-throat radius and tortuosity estimation from formation resistivity data for tight-gas sandstone reservoirs

    NASA Astrophysics Data System (ADS)

    Ziarani, Ali S.; Aguilera, Roberto

    2012-08-01

    A new model is proposed for estimation of pore-throat aperture size from formation resistivity factor and permeability data. The model is validated with data from the Mesaverde sandstone using brine salinities ranging from 20,000 to 200,000 ppm. The data analyzed includes various basins such as Green River, Piceance, Sand Wash, Powder River, Uinta, Washakie and Wind River, available in the literature. For pore-throat radii analysis the methodology involves the use of log-log plots of pore-throat radius versus the product of formation resistivity factor and permeability (rT = a(FK)b + c). The model fits over 280 samples from the Mesaverde formation with coefficients of determination varying between 0.95 and 0.99 depending primarily on the type of model used for pore throat radius calculation. The brine salinity has some minor effects on the results. The model can provide better estimates of pore-throat radii if it is calibrated with experimental techniques such as mercury porosimetry. The results show pore-throat radii varying between 0.001 and 5 μm for the Mesaverde tight sandstone; however, most of the samples fall in a range between 0.01 and 1 μm. For tortuosity analysis, the calculation involves the use of product of formation factor and porosity data. Results indicate that the estimated tortuosity values range mainly between 1 and 5. For samples with lower porosities (< 5%), tortuosity values show a wider scatter (between 1 and 8); whereas for samples with larger porosities (> 15%), the scattering in tortuosity decreases significantly. In general, for tortuosity calculation in tight gas sandstone formations, a square root model with a parameter (bf) representing various types of connecting pores, i.e., sheet-like and tubular pores, is recommended.

  1. Fluidized bed regenerators for Brayton cycles

    NASA Technical Reports Server (NTRS)

    Nichols, L. D.

    1975-01-01

    A recuperator consisting of two fluidized bed regenerators with circulating solid particles is considered for use in a Brayton cycle. These fluidized beds offer the possibility of high temperature operation if ceramic particles are used. Calculations of the efficiency and size of fluidized bed regenerators for typical values of operating parameters were made and compared to a shell and tube recuperator. The calculations indicate that the fluidized beds will be more compact than the shell and tube as well as offering a high temperature operating capability.

  2. Humid to arid to subhumid vegetation shift on Pilliga Sandstone, Ulungra Springs, New South Wales

    NASA Astrophysics Data System (ADS)

    Dodson, J. R.; Wright, R. V. S.

    1989-09-01

    The Pilliga Sandstone region of the northwest slope of New South Wales has a natural vegetation cover of sclerophyllous relatively closed to open forests with a largely heathy understorey, and a warm, subhumid and continental climate. Pollen analysis of spring-fed deposits gives a vegetation history extending from at least 30,000 yr B.P. to the late Holocene. Tree pollen became scarce after about 25,000 yr B.P. and an assemblage dominated by Chenopodiaceae, Liguliflorae, Tubuliflorae, and probably Poaceae developed. No similar assemblage is known from present pollen rain studies carried out in Australia. However, it clearly represents a treeless open shrub-steppe formation and therefore an arid or semiarid environment. The site thus provides evidence of an eastward late Pleistocene extension of the arid zone in Australia, and is the first full-glacial vegetation record between 20° and 35° latitude in Australia. The present vegetation cover did not become reestablished until the beginning of the Holocene, which raises questions about the form in which Pilliga Sandstone vegetation survived full-glacial conditions.

  3. Fluidized bed heating process and apparatus

    NASA Technical Reports Server (NTRS)

    McHale, Edward J. (Inventor)

    1981-01-01

    Capacitive electrical heating of a fluidized bed enables the individual solid particles within the bed to constitute the hottest portion thereof. This effect is achieved by applying an A. C. voltage potential between dielectric coated electrodes, one of which is advantageously the wall of the fluidized bed rejection zone, sufficient to create electrical currents in said particles so as to dissipate heat therein. In the decomposition of silane or halosilanes in a fluidized bed reaction zone, such heating enhances the desired deposition of silicon product on the surface of the seed particles within the fluidized bed and minimizes undesired coating of silicon on the wall of the reaction zone and the homogeneous formation of fine silicon powder within said zone.

  4. Space station propulsion test bed

    NASA Technical Reports Server (NTRS)

    Briley, G. L.; Evans, S. A.

    1989-01-01

    A test bed was fabricated to demonstrate hydrogen/oxygen propulsion technology readiness for the intital operating configuration (IOC) space station application. The test bed propulsion module and computer control system were delivered in December 1985, but activation was delayed until mid-1986 while the propulsion system baseline for the station was reexamined. A new baseline was selected with hydrogen/oxygen thruster modules supplied with gas produced by electrolysis of waste water from the space shuttle and space station. As a result, an electrolysis module was designed, fabricated, and added to the test bed to provide an end-to-end simulation of the baseline system. Subsequent testing of the test bed propulsion and electrolysis modules provided an end-to-end demonstration of the complete space station propulsion system, including thruster hot firings using the oxygen and hydrogen generated from electrolysis of water. Complete autonomous control and operation of all test bed components by the microprocessor control system designed and delivered during the program was demonstrated. The technical readiness of the system is now firmly established.

  5. A refined genetic model for the Laisvall and Vassbo Mississippi Valley-type sandstone-hosted deposits, Sweden: constraints from paragenetic studies, organic geochemistry, and S, C, N, and Sr isotope data

    NASA Astrophysics Data System (ADS)

    Saintilan, Nicolas J.; Spangenberg, Jorge E.; Samankassou, Elias; Kouzmanov, Kalin; Chiaradia, Massimo; Stephens, Michael B.; Fontboté, Lluís

    2016-06-01

    The current study has aimed to refine the previously proposed two-fluid mixing model for the Laisvall (sphalerite Rb-Sr age of 467 ± 5 Ma) and Vassbo Mississippi Valley-type deposits hosted in Ediacaran to Cambrian sandstone, Sweden. Premineralization cements include authigenic monazite, fluorapatite, and anatase in the Upper Sandstone at Laisvall, reflecting anoxic conditions during sandstone burial influenced by the euxinic character of the overlying carbonaceous middle Cambrian to Lower Ordovician Alum Shale Formation ( δ 13Corg = -33.0 to -29.5 ‰, δ 15Norg = 1.5 to 3.3 ‰, 0.33 to 3.03 wt% C, 0.02 to 0.08 wt% N). The available porosity for epigenetic mineralization, including that produced by subsequent partial dissolution of pre-Pb-Zn sulfide calcite and barite cements, was much higher in calcite- and barite-cemented sandstone paleoaquifers (29 % by QEMSCAN mapping) than in those mainly cemented by quartz (8 %). A major change in the Laisvall plumbing system is recognized by the transition from barite cementation to Pb-Zn sulfide precipitation in sandstone. Ba-bearing, reduced, and neutral fluids had a long premineralization residence time (highly radiogenic 87S/86Sr ratios of 0.718 to 0.723) in basement structures. As a result of an early Caledonian arc-continent collision and the development of a foreland basin, fluids migrated toward the craton and expelled Ba-bearing fluids from their host structures into overlying sandstone where they deposited barite upon mixing with a sulfate pool ( δ 34Sbarite = 14 to 33 ‰). Subsequently, slightly acidic brines initially residing in pre-Ediacaran rift sediments in the foredeep of the early Caledonian foreland basin migrated through the same plumbing system and acquired metals on the way. The bulk of Pb-Zn mineralization formed at temperatures between 120 and 180 °C by mixing of these brines with a pool of H2S ( δ 34S = 24 to 29 ‰) produced via thermochemical sulfate reduction (TSR) with oxidation of

  6. Paleomagnetic results from Northeast Anatolia: remagnetization in Late Cretaceous sandstones and tectonic rotation at the Eastern extension of the Izmir-Ankara-Erzincan suture zone

    NASA Astrophysics Data System (ADS)

    Cengiz Çinku, Mualla

    2017-12-01

    Paleomagnetic results obtained from Upper Cretaceous sandstones in Northeastern Anatolia demonstrate that the entire area from Erzincan to Kars has been remagnetised. The remagnetisation was acquired before the Middle Eocene collision between the Eastern Pontides and the Arabian Platform because Middle Eocene sandstones carry primary natural remanent magnetisations. The post-folding in situ mean direction of the Upper Cretaceous sandstones is compared with mean directions of younger, Middle Eocene to present rock formations. As a result, a two-stage antagonistic rotation mechanism is proposed. First, the collision between the Pontides and the Taurides between Late Cretaceous and Middle Eocene was associated by clockwise rotation of 26°. In the second stage between Middle Eocene and Middle Miocene and beyond, counterclockwise rotations up to 52° of the Pontide and Anatolide blocks and clockwise rotations of the Van Block were characterised by regional shortening and westward escape.

  7. Temperature dependent elasticity and damping in dehydrated sandstone

    NASA Astrophysics Data System (ADS)

    Darling, T. W.; Struble, W.

    2013-12-01

    Work reported previously at this conference, outlining our observation of anomalously large elastic softening and damping in dehydrated Berea sandstone at elevated temperatures, has been analysed to study shear and compressional effects separately. Modeling of the sample using COMSOL software was necessary to identify modes, as the vibration spectrum of the sample is poorly approximated by a uniform isotropic solid. The first torsional mode of our evacuated, dry, core softens at nearly twice the rate of Young's modulus modes (bending and compressional) and is also damped nearly twice as strongly as temperature increases. We consider two possible models for explaining this behavior, based on the assumption that the mechanical properties of the sandstone are dominated by the framework of quartz grains and polycrystalline cementation, neglecting initially the effects of clay and feldspar inclusions. The 20cm x 2.54cm diameter core is dry such that the pressure of water vapor in the experiment chamber is below 1e-6 Torr at 70C, suggesting that surface water beyond a small number of monolayers is negligible. Our models consider (1) enhanced sliding of grain boundaries in the cementation at elevated temperature and reduced internal water content, and (2) strain microcracking of the cementatioin at low water content due to anisotropic expansion in the quartz grains. In model (1) interfaces parallel to polyhedral grain surfaces were placed in the cement bonds and assigned frictional properties. Model (2) has not yet been implemented. The overall elasticity of a 3-D several-grain model network was determined by modeling quasistatic loading and measuring displacements. Initial results with a small number of grains/bonds suggests that only the first model provides softening and damping for all the modes, however the details of the effects of defect motioin at individual interfaces as the source for the frictional properties is still being evaluated. Nonlinear effects are

  8. 21 CFR 868.5180 - Rocking bed.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Rocking bed. 868.5180 Section 868.5180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5180 Rocking bed. (a) Identification. A rocking bed is a device...

  9. 21 CFR 868.5180 - Rocking bed.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Rocking bed. 868.5180 Section 868.5180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5180 Rocking bed. (a) Identification. A rocking bed is a device...

  10. 21 CFR 868.5180 - Rocking bed.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Rocking bed. 868.5180 Section 868.5180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5180 Rocking bed. (a) Identification. A rocking bed is a device...

  11. Chemical analysis of black crust on the Angkor sandstone at the Bayon temple, Cambodia

    NASA Astrophysics Data System (ADS)

    Song, Wonsuh; Oguchi, Chiaki; Waragai, Tetsuya

    2014-05-01

    The Angkor complex is the one of the greatest cultural heritages in the world. It is constructed in the early 12th century, designated as a world cultural heritage by UNESCO in 1992. The temples at the Angkor complex are mainly made of sandstone and laterite. However, due to the tropical climate, plants, lichens and various microorganisms are growing well on the rock surface. Black crusts are also easily found on the stone surface. The 21st technical session of the International Coordinating Committee for the Safeguarding and Development of the Historic Site of Angkor (ICC-Angkor) held in 2012 recommended that to preserve both the biofilms and the forest cover and to prohibit the biocides (chlorine-based) and organic biocides. However, there are many reports that lichens and microorganisms accelerate rock weathering. It is important to clarify that how the biofilm on the Angkor temples affect Angkor sandstones. We sampled Angkor sandstone covered by black crust at the Bayon temple, Angkor complex, and observed the section and the surface of the rock sample by using SEM. Surfaces of the samples are not polished in order to observe the original condition. The samples are coated with gold for 180 seconds. The depth of the black crust is up to 1 mm. Many filamentous materials were found on the black crust. Average energy-dispersive X-ray spectroscopy data of the five areas of ca. 20 μm ×15 μm in the black crusts shows that over 80 % of the filamentous materials are compounds of carbon. It seems that these materials are hyphae. The shape of the hypha is like a thread and its size is few μm in diameter and up to several centimeters in length. Black crusts are consisted of elements and compounds of carbon, Na, Mg, Al, Si, Cl, K, Ca, and Fe. Further research has to be done to find out the better and proper way of conservation for the Angkor complex.

  12. Deleterious Thermal Effects Due To Randomized Flow Paths in Pebble Bed, and Particle Bed Style Reactors

    NASA Technical Reports Server (NTRS)

    Moran, Robert P.

    2013-01-01

    A review of literature associated with Pebble Bed and Particle Bed reactor core research has revealed a systemic problem inherent to reactor core concepts which utilize randomized rather than structured coolant channel flow paths. For both the Pebble Bed and Particle Bed Reactor designs; case studies reveal that for indeterminate reasons, regions within the core would suffer from excessive heating leading to thermal runaway and localized fuel melting. A thermal Computational Fluid Dynamics model was utilized to verify that In both the Pebble Bed and Particle Bed Reactor concepts randomized coolant channel pathways combined with localized high temperature regions would work together to resist the flow of coolant diverting it away from where it is needed the most to cooler less resistive pathways where it is needed the least. In other words given the choice via randomized coolant pathways the reactor coolant will take the path of least resistance, and hot zones offer the highest resistance. Having identified the relationship between randomized coolant channel pathways and localized fuel melting it is now safe to assume that other reactor concepts that utilize randomized coolant pathways such as the foam core reactor are also susceptible to this phenomenon.

  13. Kaolinite, illite and quartz dissolution in the karstification of Paleozoic sandstones of the Furnas Formation, Paraná Basin, Southern Brazil

    NASA Astrophysics Data System (ADS)

    Melo, Mário Sérgio de; Guimarães, Gilson Burigo; Chinelatto, Adilson Luiz; Giannini, Paulo César Fonseca; Pontes, Henrique Simão; Chinelatto, Adriana Scoton Antonio; Atencio, Daniel

    2015-11-01

    Karstification processes in sandstones of the Furnas Formation, Silurian to Devonian of the Paraná Basin, have been described since the mid-twentieth century. However, some geologists still doubt the idea of true karst in sandstones. Studies carried out in the Campos Gerais region, Paraná State, Southern Brazil, aimed at investigating the nature of erosion processes in Furnas Formation and the role of the dissolution in the development of their notorious erosive features and underground cavities. These studies have led to the recognition of dissolution macro to micro features ('furnas', caves, ponds, sinks, ruiniform relief on cliffs and rocky surfaces, grain corrosion, speleothems, mineral reprecipitation and incrustation). The analysis (scanning electron microscopy, energy dispersive spectrometry and x-ray diffractometry) of sandstones and their alterites has indicated significant dissolution of clay cement along with discrete quartz grain dissolution. This mesodiagenetic cement (kaolinite and illite) is dissolved and reprecipitated as clay minerals with poorly developed crystallinity along with other minerals, such as variscite and minerals of the alunite supergroup, suggesting organic participation in the processes of dissolution and incrustation. The mineral reprecipitation usually forms centimetric speleothems, found in cavities and sheltered rocky surfaces. The cement dissolution associated with other factors (fractures, wet weather, strong hydraulic gradient, antiquity of the landforms) leads to the rock arenisation, the underground erosion and the appearance of the karst features. Carbonate rocks in the basement may locally be increasing the karst forms in the overlying Furnas Formation. The recognition of the karst character of the Furnas Formation sandstones has important implications in the management of underground water resources (increasingly exploited in the region), in the use of the unique geological heritage and in the prevention of geo

  14. Bed bug deterrence

    PubMed Central

    2010-01-01

    A recent study in BMC Biology has determined that the immature stage of the bed bug (the nymph) signals its reproductive status to adult males using pheromones and thus avoids the trauma associated with copulation in this species. The success of this nymphal strategy of deterrence is instructive. Against the background of increasing problems with bed bugs, this research raises the question whether pheromones might be used to control them. See research article http://www.biomedcentral.com/1741-7007/8/121 PMID:20828375

  15. Getting Rid of Bed Bugs

    MedlinePlus

    ... Science Water A-Z Index Laws & Regulations By Business Sector By ... Rid of Bed Bugs When a bed bug infestation is discovered there are multiple methods for controlling it. Be aware that it will ...

  16. Adult Bed-Wetting: A Concern?

    MedlinePlus

    Adult bed-wetting: A concern? My 24-year-old husband has started to wet the bed at ... of Privacy Practices Notice of Nondiscrimination Manage Cookies Advertising Mayo Clinic is a not-for-profit organization ...

  17. Fluidization quality analyzer for fluidized beds

    DOEpatents

    Daw, C. Stuart; Hawk, James A.

    1995-01-01

    A control loop and fluidization quality analyzer for a fluidized bed utilizes time varying pressure drop measurements. A fast-response pressure transducer measures the overall bed pressure drop, or over some segment of the bed, and the pressure drop signal is processed to produce an output voltage which changes with the degree of fluidization turbulence.

  18. Bed Bug Clearinghouse by Topic

    EPA Pesticide Factsheets

    This information is intended to help states, communities, and consumers prevent and control bed bug infestations. Topics include bed bug biology and behavior, detection and monitoring, non-chemical techniques such as heat treatment, and pesticides.

  19. Evolution of iron crust and clayey Ferralsol in deeply weathered sandstones of Marília Formation (Western Minas Gerais State, Brazil)

    NASA Astrophysics Data System (ADS)

    Rosolen, Vania; Bueno, Guilherme Taitson; Melfi, Adolpho José; Montes, Célia Regina; de Sousa Coelho, Carla Vanessa; Ishida, Débora Ayumi; Govone, José Silvio

    2017-11-01

    Extensive flat plateaus are typical landforms in the cratonic compartment of tropical regions. Paleoclimate, pediplanation, laterization, and dissection have created complex and distinct geological, geomorphological, and pedological features in these landscapes. In the Brazilian territory, the flat plateau sculpted in sandstone of Marília Formation (Neocretaceous) belonging to the Sul-Americana surface presents a very clayey and pisolitic Ferralsol (Red and Yellow Latossolo in the Brazilian soil classification). The clayey texture of soil and the pisolites have been considered as weathering products of a Cenozoic detritical formation which is believed to overlay the Marília Formation sandstones. Using data of petrography (optical microscopy and SEM), mineralogy (RXD), and macroscopic structures (description in the field of the arrangement of horizons and layers), a complete profile of Ferralsol with ferricrete and pisolites was studied. The complex succession of facies is in conformity with a sedimentary structure of Serra da Galga member (uppermost member of Marília Formation). The hardening hematite concentration appears as layered accretions in the subparallel clayey lenses of sandstone saprolite, preserving its structure. Iron contents varied according to different soil fabrics. Higher concentrations of iron are found in the massive ferricrete or in pisolites in the mottled horizon. Kaolinite is a dominant clay mineral and shows two micro-organizations: (1) massive fabric intrinsic to the sedimentary rock, and (2) reworked in pisolites and illuviated features. The pisolites are relicts of ferricrete in the soft bioturbated topsoil. The continuous sequence of ferricrete from saprolite to the Ferralsol indicates that the regolith is autochthonous, developed directly from sandstones of Marília Formation, through a long and intense process of laterization.

  20. Dynamics of bed bug infestations in three low-income housing communities with various bed bug management programs.

    PubMed

    Wang, Changlu; Eiden, Amanda; Singh, Narinderpal; Zha, Chen; Wang, Desen; Cooper, Richard

    2018-06-01

    Infestations of the common bed bug, Cimex lectularius L., have become common in low-income communities in the USA over the last 15 years. We evaluated community-based integrated pest management (IPM) programs for reducing bed bug infestations. Two housing authorities (Bayonne and Hackensack) implemented bed bug IPM programs. A third housing authority (Paterson) was used as the control site. Building-wide surveys were conducted in all communities, three times, to evaluate the effectiveness of the IPM programs. From 0 to 24 months, the infestation rate at Bayonne, Hackensack, and Paterson decreased by 49, 64, and 26%, respectively. The two sites that adopted IPM achieved faster bed bug elimination than the control site. The bed bug introduction rate over a 24-month period at Bayonne, Hackensack, and Paterson was 7, 3, and 11%, respectively. The introduction rate was positively associated with the initial infestation rate. Residents from buildings enrolled in IPM programs were more satisfied with the bed bug control services than residents from the control site. IPM programs were more effective in reducing bed bug infestations than traditional pest control services, but many factors contributed to the lower than desired level of reduction in infestation rate. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.