Communication Limits Due to Photon-Detector Jitter

NASA Technical Reports Server (NTRS)

Moision, Bruce E.; Farr, William H.

2008-01-01

A theoretical and experimental study was conducted of the limit imposed by photon-detector jitter on the capacity of a pulse-position-modulated optical communication system in which the receiver operates in a photon-counting (weak-signal) regime. Photon-detector jitter is a random delay between impingement of a photon and generation of an electrical pulse by the detector. In the study, jitter statistics were computed from jitter measurements made on several photon detectors. The probability density of jitter was mathematically modeled by use of a weighted sum of Gaussian functions. Parameters of the model were adjusted to fit histograms representing the measured-jitter statistics. Likelihoods of assigning detector-output pulses to correct pulse time slots in the presence of jitter were derived and used to compute channel capacities and corresponding losses due to jitter. It was found that the loss, expressed as the ratio between the signal power needed to achieve a specified capacity in the presence of jitter and that needed to obtain the same capacity in the absence of jitter, is well approximated as a quadratic function of the standard deviation of the jitter in units of pulse-time-slot duration.

Electron gun jitter effects on beam bunching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, M. S.; Iqbal, M., E-mail: muniqbal.chep@pu.edu.pk; Centre for High Energy Physics, University of the Punjab, Lahore 45590

For routine operation of Beijing Electron Positron Collider II (BEPCII) linac, many factors may affect the beam bunching process directly or indirectly. We present the measurements and analyses of the gun timing jitter, gun high voltage jitter, and beam energy at the exit of the standard acceleration section of the linac quantitatively. Almost 80 mV and more than 200 ps of gun high voltage and time jitters have ever been measured, respectively. It was analyzed that the gun timing jitter produced severe effects on beam energy than the gun high voltage jitter, if the timing jitter exceeded 100 ps whichmore » eventually deteriorates both the beam performance and the injection rate to the storage ring.« less

The Effect of Hydration on Voice Quality in Adults: A Systematic Review.

PubMed

Alves, Maxine; Krüger, Esedra; Pillay, Bhavani; van Lierde, Kristiane; van der Linde, Jeannie

2017-11-06

We aimed to critically appraise scientific, peer-reviewed articles, published in the past 10 years on the effects of hydration on voice quality in adults. This is a systematic review. Five databases were searched using the key words "vocal fold hydration", "voice quality", "vocal fold dehydration", and "hygienic voice therapy". The Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) guidelines were followed. The included studies were scored based on American Speech-Language-Hearing Association's levels of evidence and quality indicators, as well as the Cochrane Collaboration's risk of bias tool. Systemic dehydration as a result of fasting and not ingesting fluids significantly negatively affected the parameters of noise-to-harmonics ratio (NHR), shimmer, jitter, frequency, and the s/z ratio. Water ingestion led to significant improvements in shimmer, jitter, frequency, and maximum phonation time values. Caffeine intake does not appear to negatively affect voice production. Laryngeal desiccation challenges by oral breathing led to surface dehydration which negatively affected jitter, shimmer, NHR, phonation threshold pressure, and perceived phonatory effort. Steam inhalation significantly improved NHR, shimmer, and jitter. Only nebulization of isotonic solution decreased phonation threshold pressure and showed some indication of a potential positive effect of nebulization substances. Treatments in high humidity environments prove to be effective and adaptations of low humidity environments should be encouraged. Recent literature regarding vocal hydration is high quality evidence. Systemic hydration is the easiest and most cost-effective solution to improve voice quality. Recent evidence therefore supports the inclusion of hydration in a vocal hygiene program. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Fitzmaurice Voicework Pilot Study.

PubMed

Watson, Lynn; Nayak, Sadhana

2015-11-01

A repeated-measures pilot study was used to investigate acoustic changes in the voices of participants in a Fitzmaurice Voicework (FV) teacher certification program. Maximum phonation time (MPT) was also measured. Eleven participants with no reported voice problems were studied. Pretraining and posttraining recordings were made of each participant. Measures of MPT were made, and the recordings were analyzed for jitter, shimmer, and noise-to-harmonics ratio (NHR). The measure of effect size for MPT was moderate, and there was an overall increase in MPT from pretraining to posttraining, with 70% of participants showing an increase in MPT. The measure of effect sizes for jitter, shimmer, and NHR were small, with measurements showing no significant changes from pretraining to posttraining. There were indications that FV training may have positive outcomes for actors and professional voice users, particularly in increasing MPT. Further studies with larger subject groups are needed to investigate the significance of the increase in MPT noted in this study and to test whether FV training can help to lower rates of shimmer and jitter. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Analytic Method for Computing Instrument Pointing Jitter

NASA Technical Reports Server (NTRS)

Bayard, David

2003-01-01

A new method of calculating the root-mean-square (rms) pointing jitter of a scientific instrument (e.g., a camera, radar antenna, or telescope) is introduced based on a state-space concept. In comparison with the prior method of calculating the rms pointing jitter, the present method involves significantly less computation. The rms pointing jitter of an instrument (the square root of the jitter variance shown in the figure) is an important physical quantity which impacts the design of the instrument, its actuators, controls, sensory components, and sensor- output-sampling circuitry. Using the Sirlin, San Martin, and Lucke definition of pointing jitter, the prior method of computing the rms pointing jitter involves a frequency-domain integral of a rational polynomial multiplied by a transcendental weighting function, necessitating the use of numerical-integration techniques. In practice, numerical integration complicates the problem of calculating the rms pointing error. In contrast, the state-space method provides exact analytic expressions that can be evaluated without numerical integration.

ISAAC Photometric Comparison of ECLIPSE Jitter and the ORAC-DR Equivalent Recipe for ISAAC

NASA Astrophysics Data System (ADS)

Currie, M. J.

2005-12-01

Motivated by a request from astronomers demanding accurate and consistent infrared photometry, I compare the photometry and quality of mosaics generated by the ECLIPSE jitter task and the ORAC-DR JITTER_SELF_FLAT recipe in two fields. The current (v4.9.0) ECLIPSE produces photometry a few percent fainter than ORAC-DR; the systematic trend with magnitude seen in v4.4.1 is now removed. Random errors arising from poor flat-fielding are not resolved. ECLIPSE generates noisier mosaics; ORAC-DR has poorer bias removal in crowded fields and defaults to larger mosaics. ORAC-DR runs a few times slower than ECLIPSE, but its recipe development is measured in weeks, not years.

Spacecraft Jitter Attenuation Using Embedded Piezoelectric Actuators

NASA Technical Reports Server (NTRS)

Belvin, W. Keith

1995-01-01

Remote sensing from spacecraft requires precise pointing of measurement devices in order to achieve adequate spatial resolution. Unfortunately, various spacecraft disturbances induce vibrational jitter in the remote sensing instruments. The NASA Langley Research Center has performed analysis, simulations, and ground tests to identify the more promising technologies for minimizing spacecraft pointing jitter. These studies have shown that the use of smart materials to reduce spacecraft jitter is an excellent match between a maturing technology and an operational need. This paper describes the use of embedding piezoelectric actuators for vibration control and payload isolation. In addition, recent advances in modeling, simulation, and testing of spacecraft pointing jitter are discussed.

SHIMMER (1.0): a novel mathematical model for microbial and biogeochemical dynamics in glacier forefield ecosystems

NASA Astrophysics Data System (ADS)

Bradley, J. A.; Anesio, A. M.; Singarayer, J. S.; Heath, M. R.; Arndt, S.

2015-08-01

SHIMMER (Soil biogeocHemIcal Model for Microbial Ecosystem Response) is a new numerical modelling framework which is developed as part of an interdisciplinary, iterative, model-data based approach fully integrating fieldwork and laboratory experiments with model development, testing, and application. SHIMMER is designed to simulate the establishment of microbial biomass and associated biogeochemical cycling during the initial stages of ecosystem development in glacier forefield soils. However, it is also transferable to other extreme ecosystem types (such as desert soils or the surface of glaciers). The model mechanistically describes and predicts transformations in carbon, nitrogen and phosphorus through aggregated components of the microbial community as a set of coupled ordinary differential equations. The rationale for development of the model arises from decades of empirical observation on the initial stages of soil development in glacier forefields. SHIMMER enables a quantitative and process focussed approach to synthesising the existing empirical data and advancing understanding of microbial and biogeochemical dynamics. Here, we provide a detailed description of SHIMMER. The performance of SHIMMER is then tested in two case studies using published data from the Damma Glacier forefield in Switzerland and the Athabasca Glacier in Canada. In addition, a sensitivity analysis helps identify the most sensitive and unconstrained model parameters. Results show that the accumulation of microbial biomass is highly dependent on variation in microbial growth and death rate constants, Q10 values, the active fraction of microbial biomass, and the reactivity of organic matter. The model correctly predicts the rapid accumulation of microbial biomass observed during the initial stages of succession in the forefields of both the case study systems. Simulation results indicate that primary production is responsible for the initial build-up of substrate that subsequently

Correction And Use Of Jitter In Television Images

NASA Technical Reports Server (NTRS)

Diner, Daniel B.; Fender, Derek H.; Fender, Antony R. H.

1989-01-01

Proposed system stabilizes jittering television image and/or measures jitter to extract information on motions of objects in image. Alternative version, system controls lateral motion on camera to generate stereoscopic views to measure distances to objects. In another version, motion of camera controlled to keep object in view. Heart of system is digital image-data processor called "jitter-miser", which includes frame buffer and logic circuits to correct for jitter in image. Signals from motion sensors on camera sent to logic circuits and processed into corrections for motion along and across line of sight.

Developing movement recognition application with the use of Shimmer sensor and Microsoft Kinect sensor.

PubMed

Guzsvinecz, Tibor; Szucs, Veronika; Sik Lányi, Cecília

2015-01-01

Nowadays the development of virtual reality-based application is one of the most dynamically growing areas. These applications have a wide user base, more and more devices which are providing several kinds of user interactions and are available on the market. In the applications where the not-handheld devices are not necessary, the potential is that these can be used in educational, entertainment and rehabilitation applications. The purpose of this paper is to examine the precision and the efficiency of the not-handheld devices with user interaction in the virtual reality-based applications. The first task of the developed application is to support the rehabilitation process of stroke patients in their homes. A newly developed application will be introduced in this paper, which uses the two popular devices, the Shimmer sensor and the Microsoft Kinect sensor. To identify and to validate the actions of the user these sensors are working together in parallel mode. For the problem solving, the application is available to record an educational pattern, and then the software compares this pattern to the action of the user. The goal of the current research is to examine the extent of the difference in the recognition of the gestures, how precisely the two sensors are identifying the predefined actions. This could affect the rehabilitation process of the stroke patients and influence the efficiency of the rehabilitation. This application was developed in C# programming language and uses the original Shimmer connecting application as a base. During the working of this application it is possible to teach five-five different movements with the use of the Shimmer and the Microsoft Kinect sensors. The application can recognize these actions at any later time. This application uses a file-based database and the runtime memory of the application to store the saved data in order to reach the actions easier. The conclusion is that much more precise data were collected from the

Mitigating Photon Jitter in Optical PPM Communication

NASA Technical Reports Server (NTRS)

Moision, Bruce

2008-01-01

A theoretical analysis of photon-arrival jitter in an optical pulse-position-modulation (PPM) communication channel has been performed, and now constitutes the basis of a methodology for designing receivers to compensate so that errors attributable to photon-arrival jitter would be minimized or nearly minimized. Photon-arrival jitter is an uncertainty in the estimated time of arrival of a photon relative to the boundaries of a PPM time slot. Photon-arrival jitter is attributable to two main causes: (1) receiver synchronization error [error in the receiver operation of partitioning time into PPM slots] and (2) random delay between the time of arrival of a photon at a detector and the generation, by the detector circuitry, of a pulse in response to the photon. For channels with sufficiently long time slots, photon-arrival jitter is negligible. However, as durations of PPM time slots are reduced in efforts to increase throughputs of optical PPM communication channels, photon-arrival jitter becomes a significant source of error, leading to significant degradation of performance if not taken into account in design. For the purpose of the analysis, a receiver was assumed to operate in a photon- starved regime, in which photon counts follow a Poisson distribution. The analysis included derivation of exact equations for symbol likelihoods in the presence of photon-arrival jitter. These equations describe what is well known in the art as a matched filter for a channel containing Gaussian noise. These equations would yield an optimum receiver if they could be implemented in practice. Because the exact equations may be too complex to implement in practice, approximations that would yield suboptimal receivers were also derived.

Numerical Study of g-Jitter Induced Double-Diffusive Convection

NASA Technical Reports Server (NTRS)

Shu, Y.; Li, B. Q.; deGroh, Henry C.

2001-01-01

A finite element study is presented of double-diffusive convection driven by g-jitter in a microgravity environment. Mathematical formulations are presented and extensive simulations are carried out for g-jitter induced fluid flow, temperature distribution, and solutal transport in an alloy system under consideration for space flights. Computations include the use of idealized single-frequency and multi-frequency g-jitter as well as the real g-jitter data taken during an actual Space Shuttle fight. Little correlation is seen between these velocity components for the g-jitter components studied. The temperature field is basically undisturbed by convection because of a small Pr number for the fluid. The disturbance of the concentration field, however, is pronounced, and the local variation of the concentration follows the velocity oscillation in time. It is found that although the concentration field varies in both position and time, the local concentration gradient remains approximately constant in time. Numerical study further indicates that with an increase in g-jitter force (or amplitude), the nonlinear convective effects become much more obvious, which in turn drastically change the concentration fields. The simulated results computed using the g-jitter data taken during space flights show that both the velocity and concentration become random, following approximately the same pattern as the g-jitter perturbations.

Solar Dynamics Observatory (SDO) HGAS Induced Jitter

NASA Technical Reports Server (NTRS)

Liu, Alice; Blaurock, Carl; Liu, Kuo-Chia; Mule, Peter

2008-01-01

This paper presents the results of a comprehensive assessment of High Gain Antenna System induced jitter on the Solar Dynamics Observatory. The jitter prediction is created using a coupled model of the structural dynamics, optical response, control systems, and stepper motor actuator electromechanical dynamics. The paper gives an overview of the model components, presents the verification processes used to evaluate the models, describes validation and calibration tests and model-to-measurement comparison results, and presents the jitter analysis methodology and results.

Simulation of Combustion Systems with Realistic g-Jitter

NASA Technical Reports Server (NTRS)

Mell, W. E.; McGrattan, K. B.; Nakamura, Y.; Baum, H. R.

2001-01-01

A number of facilities are available for microgravity combustion experiments: aircraft, drop towers, sounding rockets, the space shuttle, and, in the future, the International Space Station (ISS). Acceleration disturbances or g-jitter about the background level of reduced gravity exist in all these microgravity facilities. While g-jitter is routinely measured, a quantitative comparison of the quality of g-jitter among the different microgravity facilities, in terms of its affects on combustion experiments, has not been compiled. Low frequency g-jitter (< 1 Hz) has been repeatedly observed to disturb a number of combustion systems. Guidelines regarding tolerable levels of acceleration disturbances for combustion experiments have been developed for use in the design of ISS experiments. The validity of these guidelines, however, remains unknown. In this project a transient, 3-D numerical model is under development to simulate the effects of realistic g-jitter on a number of combustion systems. The measured acceleration vector or some representation of it can be used as input to the simulation.

Combined Use of Standard and Throat Microphones for Measurement of Acoustic Voice Parameters and Voice Categorization.

PubMed

Uloza, Virgilijus; Padervinskis, Evaldas; Uloziene, Ingrida; Saferis, Viktoras; Verikas, Antanas

2015-09-01

The aim of the present study was to evaluate the reliability of the measurements of acoustic voice parameters obtained simultaneously using oral and contact (throat) microphones and to investigate utility of combined use of these microphones for voice categorization. Voice samples of sustained vowel /a/ obtained from 157 subjects (105 healthy and 52 pathological voices) were recorded in a soundproof booth simultaneously through two microphones: oral AKG Perception 220 microphone (AKG Acoustics, Vienna, Austria) and contact (throat) Triumph PC microphone (Clearer Communications, Inc, Burnaby, Canada) placed on the lamina of thyroid cartilage. Acoustic voice signal data were measured for fundamental frequency, percent of jitter and shimmer, normalized noise energy, signal-to-noise ratio, and harmonic-to-noise ratio using Dr. Speech software (Tiger Electronics, Seattle, WA). The correlations of acoustic voice parameters in vocal performance were statistically significant and strong (r = 0.71-1.0) for the entire functional measurements obtained for the two microphones. When classifying into healthy-pathological voice classes, the oral-shimmer revealed the correct classification rate (CCR) of 75.2% and the throat-jitter revealed CCR of 70.7%. However, combination of both throat and oral microphones allowed identifying a set of three voice parameters: throat-signal-to-noise ratio, oral-shimmer, and oral-normalized noise energy, which provided the CCR of 80.3%. The measurements of acoustic voice parameters using a combination of oral and throat microphones showed to be reliable in clinical settings and demonstrated high CCRs when distinguishing the healthy and pathological voice patient groups. Our study validates the suitability of the throat microphone signal for the task of automatic voice analysis for the purpose of voice screening. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Magnetic Damping of g-Jitter Induced Double-Diffusive Convection

NASA Technical Reports Server (NTRS)

Shu, Y.; Li, B. Q.; deGroh, H. C.

2001-01-01

This paper describes a numerical study of the g-jitter driven double diffusive convective flows, thermal and concentration distributions in binary alloy melt systems subject to an external magnetic field. The study is based on the finite element solution of transient magnetohydrodynamic equations governing the momentum, thermal and solutal transport in the melt pool. Numerical simulations are conducted using the synthesized single- and multi- frequency g-jitter as well as the real g-jitter data taken during space flights with or without an applied magnetic field. It is found that for the conditions studied, the main melt flow follows approximately a lineal- superposition of velocity components induced by individual g-jitter components, regardless of whether a magnetic field exists or not. The flow field is characterized by a recirculating double diffusive convection loop oscillating in time with a defined frequency equal to that of the driving g-jitter force. An applied magnetic field has little effect on the oscillating recirculating pattern, except around the moment in time when the flow reverses its direction. The field has no effect on the oscillation period, but it changes the phase angle. It is very effective in suppressing the flow intensity and produces a notable reduction of the solutal striation and time fluctuations in the melt. For a given magnetic field strength, the magnetic damping effect is more pronounced on the velocity associated with the largest g-jitter component present and/or the g-jitter spiking peaks. A stronger magnetic field is more effective in suppressing the melt convection and also is more helpful in bringing the convection in phase with the g-jitter driving force. The applied field is particularly useful in suppressing the effect of real g-jitter spikes on both flow and solutal distributions. With appropriately selected magnetic fields, the convective flows caused by g-jitter can be reduced sufficiently and diffusion dominant

Objective Voice Analysis of Pediatric Cochlear Implant Recipients and Comparison With Hearing Aids Users and Hearing Controls.

PubMed

Jafari, Narges; Izadi, Farzad; Salehi, Abolfazl; Dabirmoghaddam, Payman; Yadegari, Fariba; Ebadi, Abbas; Moghadam, Saeed Talebian

2017-07-01

Phonation is influenced by hearing as a feedback mechanism. The purpose of the present study was to compare selected acoustic parameters in children using cochlear implants (CIs), those using hearing aids (HA), and their normal-hearing (NH) peers. The participants were 15 children using CI (mean age: 72 months), 15 children using HA (mean age: 74 months), and 15 NH children (mean age: 77 months). The vowel /a/ was produced to measure perturbation and mean fundamental frequency. The six Persian vowels in /C b VC d / were obtained to extract vowel duration. Data were analyzed by one-way analysis of variance. Results revealed a statistically significant difference between the NH group and the HA group regarding fundamental frequency (F 2,51  = 3.443, P < 0.05), jitter local (F 2,51  = 1.629, P < 0.05), jitter local absolute (F 2,51  = 6.519, P < 0.001), jitter rap (F 2,51  = 7.151, P < 0.001), jitter ppq5 (F 2,51  = 5.894, P < 0.001), shimmer local (%) (F 2,51  = 8.070, P < 0.001), shimmer local (dB) (F 2,51  = 3.884, P < 0.05), shimmer apq3 (F 2,51  = 4.926, P < 0.05), shimmer apq5 (F 2,51  = 8.442, P < 0.001), and harmonic-to-noise ratio (F 2,51  = 4.117, P < 0.001). The mean values of the duration of all six vowels were significantly greater in children with CI and HA than in NH children (P < 0.001). It seems that after 8 months of using CI, auditory control of voice production would be enabled. Furthermore, children with hearing impairment potentially regard vowel sound duration as a distinguishing feature, whereas in NH speakers, the duration has the least effect in vowel identification. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Temporal switching jitter in photoconductive switches

DOE Office of Scientific and Technical Information (OSTI.GOV)

GAUDET,JOHN A.; SKIPPER,MICHAEL C.; ABDALLA,MICHAEL D.

This paper reports on a recent comparison made between the Air Force Research Laboratory (AFRL) gallium arsenide, optically-triggered switch test configuration and the Sandia National Laboratories (SNL) gallium arsenide, optically-triggered switch test configuration. The purpose of these measurements was to compare the temporal switch jitter times. It is found that the optical trigger laser characteristics are dominant in determining the PCSS jitter.

Solar Dynamics Observatory On-Orbit Jitter Testing, Analysis, and Mitigation Plans

NASA Technical Reports Server (NTRS)

Liu, Kuo-Chia (Alice); Blaurock, Carl A.; Bourkland, Kristin L.; Morgenstern, Wendy M.; Maghami, Peiman G.

2011-01-01

The Solar Dynamics Observatory (SDO) was designed to understand the Sun and the Sun s influence on Earth. SDO was launched on February 11, 2010 carrying three scientific instruments: the Atmospheric Imaging Assembly (AIA), the Helioseismic and Magnetic Imager (HMI), and the Extreme Ultraviolet Variability Experiment (EVE). Both AIA and HMI are sensitive to high frequency pointing perturbations and have sub-arcsecond level line-of-sight (LOS) jitter requirements. Extensive modeling and analysis efforts were directed in estimating the amount of jitter disturbing the science instruments. To verify the disturbance models and to validate the jitter performance prior to launch, many jitter-critical components and subassemblies were tested either by the mechanism vendors or at the NASA Goddard Space Flight Center (GSFC). Although detailed analysis and assembly level tests were performed to obtain good jitter predictions, there were still several sources of uncertainties in the system. The structural finite element model did not have all the modes correlated to test data at high frequencies (greater than 50 Hz). The performance of the instrument stabilization system was not known exactly but was expected to be close to the analytical model. A true disturbance-to-LOS observatory level test was not available due to the tight schedule of the flight spacecraft, the cost in time and manpower, difficulties in creating gravity negation systems, and risks of damaging flight hardware. To protect the observatory jitter performance against model uncertainties, the SDO jitter team devised several on-orbit jitter reduction plans in addition to reserve margins on analysis results. Since some of these plans severely restricted the capabilities of several spacecraft components (e.g. wheels and High Gain Antennas), the SDO team performed on-orbit jitter tests to determine which jitter reduction plans, if any, were necessary to satisfy science LOS jitter requirements. The SDO on

Solar Dynamics Observatory On-Orbit Jitter Testing, Analysis, and Mitigation Plans

NASA Technical Reports Server (NTRS)

Liu, Kuo-Chia; Blaurock, Carl A.; Bourkland, Kristin L.; Morgenstern, Wendy M.; Maghami, Peiman G.

2011-01-01

The recently launched Solar Dynamics Observatory (SDO) has two science instruments onboard that required sub-arcsecond pointing stability. Significant effort has been spent pre-launch to characterize the disturbances sources and validating jitter level at the component, sub-assembly, and spacecraft levels. However, an end-to-end jitter test emulating the flight condition was not performed on the ground due to cost and risk concerns. As a result, the true jitter level experienced on orbit remained uncertain prior to launch. Based on the pre-launch analysis, several operational constraints were placed on the observatory aimed to minimize the instrument jitter levels. If the actual jitter is below the analysis predictions, these operational constraints can be relaxed to reduce the burden of the flight operations team. The SDO team designed a three-day jitter test, utilizing the instrument sensors to measure pointing jitter up to 256 Hz. The test results were compared to pre-launch analysis predictions, used to determine which operational constraints can be relaxed, and analyzed for setting the jitter mitigation strategies for future SDO operations.

Non-Gaussian statistics of soliton timing jitter induced by amplifier noise.

PubMed

Ho, Keang-Po

2003-11-15

Based on first-order perturbation theory of the soliton, the Gordon-Haus timing jitter induced by amplifier noise is found to be non-Gaussian distributed. Both frequency and timing jitter have larger tail probabilities than Gaussian distribution given by the linearized perturbation theory. The timing jitter has a larger discrepancy from Gaussian distribution than does the frequency jitter.

How to Join a Wave: Decision-Making Processes in Shimmering Behavior of Giant Honeybees (Apis dorsata)

PubMed Central

Kastberger, Gerald; Weihmann, Frank; Hoetzl, Thomas; Weiss, Sara E.; Maurer, Michael; Kranner, Ilse

2012-01-01

Shimmering is a collective defence behaviour in Giant honeybees (Apis dorsata) whereby individual bees flip their abdomen upwards, producing Mexican wave-like patterns on the nest surface. Bucket bridging has been used to explain the spread of information in a chain of members including three testable concepts: first, linearity assumes that individual “agent bees” that participate in the wave will be affected preferentially from the side of wave origin. The directed-trigger hypothesis addresses the coincidence of the individual property of trigger direction with the collective property of wave direction. Second, continuity describes the transfer of information without being stopped, delayed or re-routed. The active-neighbours hypothesis assumes coincidence between the direction of the majority of shimmering-active neighbours and the trigger direction of the agents. Third, the graduality hypothesis refers to the interaction between an agent and her active neighbours, assuming a proportional relationship in the strength of abdomen flipping of the agent and her previously active neighbours. Shimmering waves provoked by dummy wasps were recorded with high-resolution video cameras. Individual bees were identified by 3D-image analysis, and their strength of abdominal flipping was assessed by pixel-based luminance changes in sequential frames. For each agent, the directedness of wave propagation was based on wave direction, trigger direction, and the direction of the majority of shimmering-active neighbours. The data supported the bucket bridging hypothesis, but only for a small proportion of agents: linearity was confirmed for 2.5%, continuity for 11.3% and graduality for 0.4% of surface bees (but in 2.6% of those agents with high wave-strength levels). The complimentary part of 90% of surface bees did not conform to bucket bridging. This fuzziness is discussed in terms of self-organisation and evolutionary adaptedness in Giant honeybee colonies to respond to rapidly

How to join a wave: decision-making processes in shimmering behavior of Giant honeybees (Apis dorsata).

PubMed

Kastberger, Gerald; Weihmann, Frank; Hoetzl, Thomas; Weiss, Sara E; Maurer, Michael; Kranner, Ilse

2012-01-01

Shimmering is a collective defence behaviour in Giant honeybees (Apis dorsata) whereby individual bees flip their abdomen upwards, producing Mexican wave-like patterns on the nest surface. Bucket bridging has been used to explain the spread of information in a chain of members including three testable concepts: first, linearity assumes that individual "agent bees" that participate in the wave will be affected preferentially from the side of wave origin. The directed-trigger hypothesis addresses the coincidence of the individual property of trigger direction with the collective property of wave direction. Second, continuity describes the transfer of information without being stopped, delayed or re-routed. The active-neighbours hypothesis assumes coincidence between the direction of the majority of shimmering-active neighbours and the trigger direction of the agents. Third, the graduality hypothesis refers to the interaction between an agent and her active neighbours, assuming a proportional relationship in the strength of abdomen flipping of the agent and her previously active neighbours. Shimmering waves provoked by dummy wasps were recorded with high-resolution video cameras. Individual bees were identified by 3D-image analysis, and their strength of abdominal flipping was assessed by pixel-based luminance changes in sequential frames. For each agent, the directedness of wave propagation was based on wave direction, trigger direction, and the direction of the majority of shimmering-active neighbours. The data supported the bucket bridging hypothesis, but only for a small proportion of agents: linearity was confirmed for 2.5%, continuity for 11.3% and graduality for 0.4% of surface bees (but in 2.6% of those agents with high wave-strength levels). The complimentary part of 90% of surface bees did not conform to bucket bridging. This fuzziness is discussed in terms of self-organisation and evolutionary adaptedness in Giant honeybee colonies to respond to rapidly

Effects of singing training on the speaking voice of voice majors.

PubMed

Mendes, Ana P; Brown, W S; Rothman, Howard B; Sapienza, Christine

2004-03-01

This longitudinal study gathered data with regard to the question: Does singing training have an effect on the speaking voice? Fourteen voice majors (12 females and two males; age range 17 to 20 years) were recorded once a semester for four consecutive semesters, while sustaining vowels and reading the "Rainbow Passage." Acoustic measures included speaking fundamental frequency (SFF) and sound pressure level (SLP). Perturbation measures included jitter, shimmer, and harmonic-to-noise ratio. Temporal measures included sentence, consonant, and diphthong durations. Results revealed that, as the number of semesters increased, the SFF increased while jitter and shimmer slightly decreased. Repeated measure analysis, however, indicated that none of the acoustic, temporal, or perturbation differences were statistically significant. These results confirm earlier cross-sectional studies that compared singers with nonsingers, in that singing training mostly affects the singing voice and rarely the speaking voice.

Goodbye Critter Jitters

ERIC Educational Resources Information Center

Eidietis, Laura; Gray, Stacey; Riggs, Leela; West, Bridgette; Coffman, Margaret

2007-01-01

What invertebrates make the best classroom pets? How should we care for each invertebrate? What type of inquiry activities could invertebrates support? How do elementary students respond to invertebrates? These were the questions investigated in The Critter Project, a three-week project that aimed to help students conquer their "critter jitters"…

Spark gap with low breakdown voltage jitter

DOEpatents

Rohwein, G.J.; Roose, L.D.

1996-04-23

Novel spark gap devices and electrodes are disclosed. The novel spark gap devices and electrodes are suitable for use in a variety of spark gap device applications. The shape of the electrodes gives rise to local field enhancements and reduces breakdown voltage jitter. Breakdown voltage jitter of approximately 5% has been measured in spark gaps according the invention. Novel electrode geometries and materials are disclosed. 13 figs.

An Adaptive Jitter Mechanism for Reactive Route Discovery in Sensor Networks

PubMed Central

Cordero, Juan Antonio; Yi, Jiazi; Clausen, Thomas

2014-01-01

This paper analyses the impact of jitter when applied to route discovery in reactive (on-demand) routing protocols. In multi-hop non-synchronized wireless networks, jitter—a small, random variation in the timing of message emission—is commonly employed, as a means to avoid collisions of simultaneous transmissions by adjacent routers over the same channel. In a reactive routing protocol for sensor and ad hoc networks, jitter is recommended during the route discovery process, specifically, during the network-wide flooding of route request messages, in order to avoid collisions. Commonly, a simple uniform jitter is recommended. Alas, this is not without drawbacks: when applying uniform jitter to the route discovery process, an effect called delay inversion is observed. This paper, first, studies and quantifies this delay inversion effect. Second, this paper proposes an adaptive jitter mechanism, designed to alleviate the delay inversion effect and thereby to reduce the route discovery overhead and (ultimately) allow the routing protocol to find more optimal paths, as compared to uniform jitter. This paper presents both analytical and simulation studies, showing that the proposed adaptive jitter can effectively decrease the cost of route discovery and increase the path quality. PMID:25111238

Corrective jitter motion shows similar individual frequencies for the arm and the finger.

PubMed

Noy, Lior; Alon, Uri; Friedman, Jason

2015-04-01

A characteristic of visuomotor tracking of non-regular oscillating stimuli are high-frequency jittery corrective motions, oscillating around the tracked stimuli. However, the properties of these corrective jitter responses are not well understood. For example, does the jitter response show an idiosyncratic signature? What is the relationship between stimuli properties and jitter properties? Is the jitter response similar across effectors with different inertial properties? To answer these questions, we measured participants' jitter frequencies in two tracking tasks in the arm and the finger. Thirty participants tracked the same set of eleven non-regular oscillating stimuli, vertically moving on a screen, once with forward-backward arm movements (holding a tablet stylus) and once with upward-downward index finger movements (with a motion tracker attached). Participants' jitter frequencies and tracking errors varied systematically as a function of stimuli frequency and amplitude. Additionally, there were clear individual differences in average jitter frequencies between participants, ranging from 0.7 to 1.15 Hz, similar to values reported previously. A comparison of individual jitter frequencies in the two tasks showed a strong correlation between participants' jitter frequencies in the finger and the arm, despite the very different inertial properties of the two effectors. This result suggests that the corrective jitter response stems from common neural processes.

UARS in-flight jitter study for EOS

NASA Technical Reports Server (NTRS)

Molnar, John; Garnek, Mike

1993-01-01

Response data collected from gyroscopes on board the Upper Atmosphere Research Satellite (UARS) provided a unique opportunity to analyze actual flight pointing jitter data. Flight modal frequencies and damping values are derived from the measured data using an Eigensystem Realization Algorithm (ERA). Flight frequencies at various solar array positions are compared to analytical predictions obtained with a Finite Element Model. The solar array modal frequencies change with position due to the modes acting about different spacecraft inertial axes. Higher order modes were difficult to identify due to the limited instrumentation. Future flight jitter studies on other spacecraft would be significantly aided by additional instrumentation. Spacecraft jitter due to continuous disturbance sources such as the 1.6 meter scanning microwave antenna, the solar array drive, and reaction wheels is presented. The solar array drive disturbance dominates the spacecraft response during normal operation.

SHIMMER (1.0): a novel mathematical model for microbial and biogeochemical dynamics in glacier forefield ecosystems

NASA Astrophysics Data System (ADS)

Bradley, J. A.; Anesio, A. M.; Singarayer, J. S.; Heath, M. R.; Arndt, S.

2015-10-01

SHIMMER (Soil biogeocHemIcal Model for Microbial Ecosystem Response) is a new numerical modelling framework designed to simulate microbial dynamics and biogeochemical cycling during initial ecosystem development in glacier forefield soils. However, it is also transferable to other extreme ecosystem types (such as desert soils or the surface of glaciers). The rationale for model development arises from decades of empirical observations in glacier forefields, and enables a quantitative and process focussed approach. Here, we provide a detailed description of SHIMMER, test its performance in two case study forefields: the Damma Glacier (Switzerland) and the Athabasca Glacier (Canada) and analyse sensitivity to identify the most sensitive and unconstrained model parameters. Results show that the accumulation of microbial biomass is highly dependent on variation in microbial growth and death rate constants, Q10 values, the active fraction of microbial biomass and the reactivity of organic matter. The model correctly predicts the rapid accumulation of microbial biomass observed during the initial stages of succession in the forefields of both the case study systems. Primary production is responsible for the initial build-up of labile substrate that subsequently supports heterotrophic growth. However, allochthonous contributions of organic matter, and nitrogen fixation, are important in sustaining this productivity. The development and application of SHIMMER also highlights aspects of these systems that require further empirical research: quantifying nutrient budgets and biogeochemical rates, exploring seasonality and microbial growth and cell death. This will lead to increased understanding of how glacier forefields contribute to global biogeochemical cycling and climate under future ice retreat.

Acoustic analysis of voice in children with cleft palate and velopharyngeal insufficiency.

PubMed

Villafuerte-Gonzalez, Rocio; Valadez-Jimenez, Victor M; Hernandez-Lopez, Xochiquetzal; Ysunza, Pablo Antonio

2015-07-01

Acoustic analysis of voice can provide instrumental data concerning vocal abnormalities. These findings can be used for monitoring clinical course in cases of voice disorders. Cleft palate severely affects the structure of the vocal tract. Hence, voice quality can also be also affected. To study whether the main acoustic parameters of voice, including fundamental frequency, shimmer and jitter are significantly different in patients with a repaired cleft palate, as compared with normal children without speech, language and voice disorders. Fourteen patients with repaired unilateral cleft lip and palate and persistent or residual velopharyngeal insufficiency (VPI) were studied. A control group was assembled with healthy volunteer subjects matched by age and gender. Hypernasality and nasal emission were perceptually assessed in patients with VPI. Size of the gap as assessed by videonasopharyngoscopy was classified in patients with VPI. Acoustic analysis of voice including Fundamental frequency (F0), shimmer and jitter were compared between patients with VPI and control subjects. F0 was significantly higher in male patients as compared with male controls. Shimmer was significantly higher in patients with VPI regardless of gender. Moreover, patients with moderate VPI showed a significantly higher shimmer perturbation, regardless of gender. Although future research regarding voice disorders in patients with VPI is needed, at the present time it seems reasonable to include strategies for voice therapy in the speech and language pathology intervention plan for patients with VPI. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Acoustic Characteristics in Epiglottic Cyst.

PubMed

Lee, YeonWoo; Kim, GeunHyo; Wang, SooGeun; Jang, JeonYeob; Cha, Wonjae; Choi, HongSik; Kim, HyangHee

2018-05-03

The purpose of this study was to analyze the acoustic characteristics associated with alternation deformation of the vocal tract due to large epiglottic cyst, and to confirm the relation between the anatomical change and resonant function of the vocal tract. Eight men with epiglottic cyst were enrolled in this study. The jitter, shimmer, noise-to-harmonic ratio, and first two formants were analyzed in vowels /a:/, /e:/, /i:/, /o:/, and /u:/. These values were analyzed before and after laryngeal microsurgery. The F1 value of /a:/ was significantly raised after surgery. Significant differences of formant frequencies in other vowels, jitter, shimmer, and noise-to-harmonic ratio were not presented. The results of this study could be used to analyze changes in the resonance of vocal tracts due to the epiglottic cysts. Copyright © 2018 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Influence of the platform jitter on intensity fluctuation for laser launch system

NASA Astrophysics Data System (ADS)

Zhang, Pengfei; Qiao, Chunhong; Huang, Tong; Zhang, Jinghui; Fan, Chengyu

2017-10-01

The jitter of the transmitting system can cause the light intensity fluctuation at the target position of the laser transmission, which affects the performance of the laser communication, imaging and the adaptive optical system. In this paper, the platform jitter is modeled by Gaussian random fluctuation phase and the analytic expression of the system jitter effect on the fluctuation of light intensity is obtained under the vacuum condition based on extended Huygens-Fresnel principle. The numerical simulation is compared with the theoretical expression and the consistency is obtained. At the same time, the influence of the jitter of the launch system on the intensity fluctuation of the target system under different turbulence conditions is analyzed by numerical simulation. The result show that normalized intensity fluctuation variance induced by platform jitter seems to be unrestricted. The jitter of the transmitting system has a more important influence on the fluctuation of the target position caused by the atmospheric turbulence, as the jitter increase. This result provides a reference for the application of the actual laser transmission system.

Image jitter enhances visual performance when spatial resolution is impaired.

PubMed

Watson, Lynne M; Strang, Niall C; Scobie, Fraser; Love, Gordon D; Seidel, Dirk; Manahilov, Velitchko

2012-09-06

Visibility of low-spatial frequency stimuli improves when their contrast is modulated at 5 to 10 Hz compared with stationary stimuli. Therefore, temporal modulations of visual objects could enhance the performance of low vision patients who primarily perceive images of low-spatial frequency content. We investigated the effect of retinal-image jitter on word recognition speed and facial emotion recognition in subjects with central visual impairment. Word recognition speed and accuracy of facial emotion discrimination were measured in volunteers with AMD under stationary and jittering conditions. Computer-driven and optoelectronic approaches were used to induce retinal-image jitter with duration of 100 or 166 ms and amplitude within the range of 0.5 to 2.6° visual angle. Word recognition speed was also measured for participants with simulated (Bangerter filters) visual impairment. Text jittering markedly enhanced word recognition speed for people with severe visual loss (101 ± 25%), while for those with moderate visual impairment, this effect was weaker (19 ± 9%). The ability of low vision patients to discriminate the facial emotions of jittering images improved by a factor of 2. A prototype of optoelectronic jitter goggles produced similar improvement in facial emotion discrimination. Word recognition speed in participants with simulated visual impairment was enhanced for interjitter intervals over 100 ms and reduced for shorter intervals. Results suggest that retinal-image jitter with optimal frequency and amplitude is an effective strategy for enhancing visual information processing in the absence of spatial detail. These findings will enable the development of novel tools to improve the quality of life of low vision patients.

[Acoustic voice analysis using the Praat program: comparative study with the Dr. Speech program].

PubMed

Núñez Batalla, Faustino; González Márquez, Rocío; Peláez González, M Belén; González Laborda, Irene; Fernández Fernández, María; Morato Galán, Marta

2014-01-01

The European Laryngological Society (ELS) basic protocol for functional assessment of voice pathology includes 5 different approaches: perception, videostroboscopy, acoustics, aerodynamics and subjective rating by the patient. In this study we focused on acoustic voice analysis. The purpose of the present study was to correlate the results obtained by the commercial software Dr. Speech and the free software Praat in 2 fields: 1. Narrow-band spectrogram (the presence of noise according to Yanagihara, and the presence of subharmonics) (semi-quantitative). 2. Voice acoustic parameters (jitter, shimmer, harmonics-to-noise ratio, fundamental frequency) (quantitative). We studied a total of 99 voice samples from individuals with Reinke's oedema diagnosed using videostroboscopy. One independent observer used Dr. Speech 3.0 and a second one used the Praat program (Phonetic Sciences, University of Amsterdam). The spectrographic analysis consisted of obtaining a narrow-band spectrogram from the previous digitalised voice samples by the 2 independent observers. They then determined the presence of noise in the spectrogram, using the Yanagihara grades, as well as the presence of subharmonics. As a final result, the acoustic parameters of jitter, shimmer, harmonics-to-noise ratio and fundamental frequency were obtained from the 2 acoustic analysis programs. The results indicated that the sound spectrogram and the numerical values obtained for shimmer and jitter were similar for both computer programs, even though types 1, 2 and 3 voice samples were analysed. The Praat and Dr. Speech programs provide similar results in the acoustic analysis of pathological voices. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Effects of steam inhalation on voice quality-related acoustic measures.

PubMed

Mahalingam, Shenbagavalli; Boominathan, Prakash

2016-10-01

To investigate the effects of steam inhalation using a facial steamer on voice quality-related acoustic measures. Prospective outcome research: single-blinded experimental study. Forty-five vocally healthy female subjects ranging in age from 18 to 30 years (Mean age: 22.41 years; standard deviation [SD]: 8.91) participated in the study. Phonation samples were recorded under three different conditions in triplicate: baseline recording, immediately after mouth breathing (dehydration), and immediately after 3 minutes of steam inhalation via the mouth (rehydration). In the initial voice recording (prior to dehydration), mean jitter (0.42 %; SD: 0.07), shimmer (2.20 dB; SD: 0.45), and harmonics-to-noise ratio (HNR) (21.60; SD: 2.41) values were within normal limits. After short-term mouth breathing (dehydration, approximately 10 minutes), the mean jitter (1.57 %; SD: 1.82) and shimmer (4.73 dB; SD: 1.83) were significantly increased (P < 0.05), and HNR (18.64; SD: 3.16) was reduced (P < 0.05). After steam inhalation (rehydration) for 3 minutes, mean jitter (0.48 %; SD: 0.12) and shimmer (2.70 dB; SD: 0.71) showed significant decrease (P < 0.05), and HNR (20.10; SD: 3.69) showed significant increase (P < 0.05). All parameters statistically significantly improved from post dehydration values. The simple procedure of steam inhalation using a facial steamer displayed positive effects on parameters proposed to reflect voice quality. 4. Laryngoscope, 126:2305-2309, 2016. © 2016 The American Laryngological, Rhinological and Otological Society, Inc.

Zero-crossing detector with sub-microsecond jitter and crosstalk

NASA Technical Reports Server (NTRS)

Dick, G. John; Kuhnle, Paul F.; Sydnor, Richard L.

1990-01-01

A zero-crossing detector (ZCD) was built and tested with a new circuit design which gives reduced time jitter compared to previous designs. With the new design, time jitter is reduced for the first time to a value which approaches that due to noise in the input amplifying stage. Additionally, with fiber-optic transmission of the output signal, crosstalk between units has been eliminated. The measured values are in good agreement with circuit noise calculations and approximately ten times lower than that for ZCD's presently installed in the JPL test facility. Crosstalk between adjacent units was reduced even more than the jitter.

Correcting spacecraft jitter in HiRISE images

USGS Publications Warehouse

Sutton, S. S.; Boyd, A.K.; Kirk, Randolph L.; Cook, Debbie; Backer, Jean; Fennema, A.; Heyd, R.; McEwen, A.S.; Mirchandani, S.D.; Wu, B.; Di, K.; Oberst, J.; Karachevtseva, I.

2017-01-01

Mechanical oscillations or vibrations on spacecraft, also called pointing jitter, cause geometric distortions and/or smear in high resolution digital images acquired from orbit. Geometric distortion is especially a problem with pushbroom type sensors, such as the High Resolution Imaging Science Experiment (HiRISE) instrument on board the Mars Reconnaissance Orbiter (MRO). Geometric distortions occur at a range of frequencies that may not be obvious in the image products, but can cause problems with stereo image correlation in the production of digital elevation models, and in measuring surface changes over time in orthorectified images. The HiRISE focal plane comprises a staggered array of fourteen charge-coupled devices (CCDs) with pixel IFOV of 1 microradian. The high spatial resolution of HiRISE makes it both sensitive to, and an excellent recorder of jitter. We present an algorithm using Fourier analysis to resolve the jitter function for a HiRISE image that is then used to update instrument pointing information to remove geometric distortions from the image. Implementation of the jitter analysis and image correction is performed on selected HiRISE images. Resulting corrected images and updated pointing information are made available to the public. Results show marked reduction of geometric distortions. This work has applications to similar cameras operating now, and to the design of future instruments (such as the Europa Imaging System).

Active suppression of acoustically induced jitter for the airborne laser

NASA Astrophysics Data System (ADS)

Glaese, Roger M.; Anderson, Eric H.; Janzen, Paul C.

2000-07-01

The Airborne Laser (ABL) system has extremely tight jitter requirements. Acoustic disturbances, such as those caused by the pressure recovery system of the high power laser, are a significant jitter source. Several technologies may be appropriate for reducing the acoustically induced jitter. The first choice for mitigation will be passive approaches, such as acoustic blankets. There is, however, some uncertainty whether these approaches will provide sufficient attenuation and there is concern about the weight of these approaches. A testbed that captured the fundamental physics of the ABL acoustically induced optical jitter problem was developed. This testbed consists of a flexure-mounted mirror exposed to an acoustic field that is generated outside a beam tube and then propagates within the tube. Both feedback and adaptive feedforward control topologies were implemented on the testbed using either of two actuators (a fast steering mirror and a secondary acoustic speaker located near the precision mirror), and a variety of sensors (microphones measuring the acoustic disturbance, accelerometers and microphones mounted on the precision optic, and an optical position sensing detector). This paper summarizes the results from these control topologies for reducing the acoustically induced jitter with some control topologies achieving in excess of 40 dB jitter reduction at a single frequency. This work was performed under an SBIR Phase I funded by the Air Force Research Laboratory Space Vehicles Directorate.

Perceptual and acoustic study of professionally trained versus untrained voices.

PubMed

Brown, W S; Rothman, H B; Sapienza, C M

2000-09-01

Acoustic and perceptual analyses were completed to determine the effect of vocal training on professional singers when speaking and singing. Twenty professional singers and 20 nonsingers, acting as the control, were recorded while sustaining a vowel, reading a modified Rainbow Passage, and singing "America the Beautiful." Acoustic measures included fundamental frequency, duration, percent jitter, percent shimmer, noise-to-harmonic ratio, and determination of the presence or absence of both vibrato and the singer's formant. Results indicated that, whereas certain acoustic parameters differentiated singers from nonsingers within sex, no consistently significant trends were found across males and females for either speaking or singing. The most consistent differences were the presence or absence of the singer's vibrato and formant in the singers versus the nonsingers, respectively. Perceptual analysis indicated that singers could be correctly identified with greater frequency than by chance alone from their singing, but not their speaking utterances.

Adaptive Filter Techniques for Optical Beam Jitter Control and Target Tracking

DTIC Science & Technology

2008-12-01

OPTICAL BEAM JITTER CONTROL AND TARGET TRACKING Michael J. Beerer Civilian, United States Air Force B.S., University of California Irvine, 2006...TECHNIQUES FOR OPTICAL BEAM JITTER CONTROL AND TARGET TRACKING by Michael J. Beerer December 2008 Thesis Advisor: Brij N. Agrawal Co...DATE December 2008 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE Adaptive Filter Techniques for Optical Beam Jitter

Jitter Reduces Response-Time Variability in ADHD: An Ex-Gaussian Analysis.

PubMed

Lee, Ryan W Y; Jacobson, Lisa A; Pritchard, Alison E; Ryan, Matthew S; Yu, Qilu; Denckla, Martha B; Mostofsky, Stewart; Mahone, E Mark

2015-09-01

"Jitter" involves randomization of intervals between stimulus events. Compared with controls, individuals with ADHD demonstrate greater intrasubject variability (ISV) performing tasks with fixed interstimulus intervals (ISIs). Because Gaussian curves mask the effect of extremely slow or fast response times (RTs), ex-Gaussian approaches have been applied to study ISV. This study applied ex-Gaussian analysis to examine the effects of jitter on RT variability in children with and without ADHD. A total of 75 children, aged 9 to 14 years (44 ADHD, 31 controls), completed a go/no-go test with two conditions: fixed ISI and jittered ISI. ADHD children showed greater variability, driven by elevations in exponential (tau), but not normal (sigma) components of the RT distribution. Jitter decreased tau in ADHD to levels not statistically different than controls, reducing lapses in performance characteristic of impaired response control. Jitter may provide a nonpharmacologic mechanism to facilitate readiness to respond and reduce lapses from sustained (controlled) performance. © 2012 SAGE Publications.

A pattern jitter free AFC scheme for mobile satellite systems

NASA Technical Reports Server (NTRS)

Yoshida, Shousei

1993-01-01

This paper describes a scheme for pattern jitter free automatic frequency control (AFC) with a wide frequency acquisition range. In this scheme, equalizing signals fed to the frequency discriminator allow pattern jitter free performance to be achieved for all roll-off factors. In order to define the acquisition range, frequency discrimination characateristics are analyzed on a newly derived frequency domain model. As a result, it is shown that a sufficiently wide acquisition range over a given system symbol rate can be achieved independent of symbol timing errors. Additionally, computer simulation demonstrates that frequency jitter performance improves in proportion to E(sub b)/N(sub 0) because pattern-dependent jitter is suppressed in the discriminator output. These results show significant promise for applciation to mobile satellite systems, which feature relatively low symbol rate transmission with an approximately 0.4-0.7 roll-off factor.

Voice Signals Produced With Jitter Through a Stochastic One-mass Mechanical Model.

PubMed

Cataldo, Edson; Soize, Christian

2017-01-01

The quasiperiodic oscillation of the vocal folds causes perturbations in the length of the glottal cycles, which are known as jitter. The observation of the glottal cycles variations suggests that jitter is a random phenomenon described by random deviations of the glottal cycle lengths in relation to a corresponding mean value and, in general, its values are expressed as a percentage of the duration of the glottal pulse. The objective of this paper is the construction of a stochastic model for jitter using a one-mass mechanical model of the vocal folds, which assumes complete right-left symmetry of the vocal folds, and which considers motions of the vocal folds only in the horizontal direction. The jitter has been the subject for researchers due to its important applications such as the identification of pathological voices (nodules in the vocal folds, paralysis of the vocal folds, or even, the vocal aging, among others). Large values for jitter variations can indicate a pathological characteristic of the voice. The corresponding stiffness of each vocal fold is considered as a stochastic process, and its modeling is proposed. The probability density function of the fundamental frequency related to the voice signals produced are constructed and compared for different levels of jitter. Some samples of synthesized voices in these cases are obtained. It is showed that jitter could be obtained using the model proposed. The Praat software was also used to verify the measures of jitter in the synthesized voice signals. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Acoustic Analysis and Electroglottography in Elite Vocal Performers.

PubMed

Villafuerte-Gonzalez, Rocio; Valadez-Jimenez, Victor M; Sierra-Ramirez, Jose A; Ysunza, Pablo Antonio; Chavarria-Villafuerte, Karen; Hernandez-Lopez, Xochiquetzal

2017-05-01

Acoustic analysis of voice (AAV) and electroglottography (EGG) have been used for assessing vocal quality in patients with voice disorders. The effectiveness of these procedures for detecting mild disturbances in vocal quality in elite vocal performers has been controversial. To compare acoustic parameters obtained by AAV and EGG before and after vocal training to determine the effectiveness of these procedures for detecting vocal improvements in elite vocal performers. Thirty-three elite vocal performers were studied. The study group included 14 males and 19 females, ages 18-40 years, without a history of voice disorders. Acoustic parameters were obtained through AAV and EGG before and after vocal training using the Linklater method. Nonsignificant differences (P > 0.05) were found between values of fundamental frequency (F 0 ), shimmer, and jitter obtained by both procedures before vocal training. Mean F 0 was similar after vocal training. Jitter percentage as measured by AAV showed nonsignificant differences (P > 0.05) before and after vocal training. Shimmer percentage as measured by AAV demonstrated a significant reduction (P < 0.05) after vocal training. As measured by EGG after vocal training, shimmer and jitter were significantly reduced (P < 0.05); open quotient was significantly increased (P < 0.05); and irregularity was significantly reduced (P < 0.05). AAV and EGG were effective for detecting improvements in vocal function after vocal training in male and female elite vocal performers undergoing vocal training. EGG demonstrated better efficacy for detecting improvements and provided additional parameters as compared to AAV. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Objective Dysphonia Quantification in Vocal Fold Paralysis: Comparing Nonlinear with Classical Measures

PubMed Central

Little, Max A.; Costello, Declan A. E.; Harries, Meredydd L.

2010-01-01

Summary Clinical acoustic voice-recording analysis is usually performed using classical perturbation measures, including jitter, shimmer, and noise-to-harmonic ratios (NHRs). However, restrictive mathematical limitations of these measures prevent analysis for severely dysphonic voices. Previous studies of alternative nonlinear random measures addressed wide varieties of vocal pathologies. Here, we analyze a single vocal pathology cohort, testing the performance of these alternative measures alongside classical measures. We present voice analysis pre- and postoperatively in 17 patients with unilateral vocal fold paralysis (UVFP). The patients underwent standard medialization thyroplasty surgery, and the voices were analyzed using jitter, shimmer, NHR, nonlinear recurrence period density entropy (RPDE), detrended fluctuation analysis (DFA), and correlation dimension. In addition, we similarly analyzed 11 healthy controls. Systematizing the preanalysis editing of the recordings, we found that the novel measures were more stable and, hence, reliable than the classical measures on healthy controls. RPDE and jitter are sensitive to improvements pre- to postoperation. Shimmer, NHR, and DFA showed no significant change (P > 0.05). All measures detect statistically significant and clinically important differences between controls and patients, both treated and untreated (P < 0.001, area under curve [AUC] > 0.7). Pre- to postoperation grade, roughness, breathiness, asthenia, and strain (GRBAS) ratings show statistically significant and clinically important improvement in overall dysphonia grade (G) (AUC = 0.946, P < 0.001). Recalculating AUCs from other study data, we compare these results in terms of clinical importance. We conclude that, when preanalysis editing is systematized, nonlinear random measures may be useful for monitoring UVFP-treatment effectiveness, and there may be applications to other forms of dysphonia. PMID:19900790

Remote distribution of a mode-locked pulse train with sub 40-as jitter

NASA Astrophysics Data System (ADS)

Chen, Yi-Fei; Jiang, Jie; Jones, David J.

2006-12-01

Remote transfer of an ultralow-jitter microwave frequency reference signal is demonstrated using the pulse trains generated by a mode-locked fiber laser. The timing jitter in a ~ 30-m fiber link is reduced to 38 attoseconds (as) integrated over a bandwidth from 1 Hz to 10 MHz via active stabilization which represents a significant improvement over previously reported jitter performance. Our approach uses an all-optical generation of the synchronization error signal and an accompanying out-of-loop optical detection technique to verify the jitter performance.

Physical mechanisms of timing jitter in photon detection by current-carrying superconducting nanowires

NASA Astrophysics Data System (ADS)

Sidorova, Mariia; Semenov, Alexej; Hübers, Heinz-Wilhelm; Charaev, Ilya; Kuzmin, Artem; Doerner, Steffen; Siegel, Michael

2017-11-01

We studied timing jitter in the appearance of photon counts in meandering nanowires with different fractional amount of bends. Intrinsic timing jitter, which is the probability density function of the random time delay between photon absorption in current-carrying superconducting nanowire and appearance of the normal domain, reveals two different underlying physical mechanisms. In the deterministic regime, which is realized at large photon energies and large currents, jitter is controlled by position-dependent detection threshold in straight parts of meanders. It decreases with the increase in the current. At small photon energies, jitter increases and its current dependence disappears. In this probabilistic regime jitter is controlled by Poisson process in that magnetic vortices jump randomly across the wire in areas adjacent to the bends.

An evaluation of voice stress analysis techniques in a simulated AWACS environment

NASA Astrophysics Data System (ADS)

Jones, William A., Jr.

1990-08-01

The purpose was to determine if voice analysis algorithms are an effective measure of stress resulting from high workload. Fundamental frequency, frequency jitter, and amplitude shimmer algorithms were employed to measure the effects of stress in crewmember communications data in simulated AWACS mission scenarios. Two independent workload measures were used to identify levels of stress: a predictor model developed by the simulation author based upon scenario generated stimulus events; and the duration of communication for each weapons director, representative of the individual's response to the induced stress. Between eight and eleven speech samples were analyzed for each of the sixteen Air Force officers who participated in the study. Results identified fundamental frequency and frequency jitter as statistically significant vocal indicators of stress, while amplitude shimmer showed no signs of any significant relationship with workload or stress. Consistent with previous research, the frequency algorithm was identified as the most reliable measure. However, the results did not reveal a sensitive discrimination measure between levels of stress, but rather, did distinguish between the presence or absence of stress. The results illustrate a significant relationship between fundamental frequency and the effects of stress and also a significant inverse relationship with jitter, though less dramatic.

Jitter Test Program and On-Orbit Mitigation Strategies for Solar Dynamic Observatory

NASA Technical Reports Server (NTRS)

Liu, Kuo-Chia; Kenney, Thomas; Maghami, Peiman; Mule, Pete; Blaurock, Carl; Haile, William B.

2007-01-01

The Solar Dynamic Observatory (SDO) aims to study the Sun's influence on the Earth, the source, storage, and release of the solar energy, and the interior structure of the Sun. During science observations, the jitter stability at the instrument focal plane must be maintained to less than a fraction of an arcsecond for two of the SDO instruments. To meet these stringent requirements, a significant amount of analysis and test effort has been devoted to predicting the jitter induced from various disturbance sources. This paper presents an overview of the SDO jitter analysis approach and test effort performed to date. It emphasizes the disturbance modeling, verification, calibration, and validation of the high gain antenna stepping mechanism and the reaction wheels, which are the two largest jitter contributors. This paper also describes on-orbit mitigation strategies to protect the system from analysis model uncertainties. Lessons learned from the SDO jitter analyses and test programs are included in the paper to share the knowledge gained with the community.

Jitter model and signal processing techniques for pulse width modulation optical recording

NASA Technical Reports Server (NTRS)

Liu, Max M.-K.

1991-01-01

A jitter model and signal processing techniques are discussed for data recovery in Pulse Width Modulation (PWM) optical recording. In PWM, information is stored through modulating sizes of sequential marks alternating in magnetic polarization or in material structure. Jitter, defined as the deviation from the original mark size in the time domain, will result in error detection if it is excessively large. A new approach is taken in data recovery by first using a high speed counter clock to convert time marks to amplitude marks, and signal processing techniques are used to minimize jitter according to the jitter model. The signal processing techniques include motor speed and intersymbol interference equalization, differential and additive detection, and differential and additive modulation.

Investigating the initial stages of soil formation in glacier forefields using the new biogeochemical model: SHIMMER

NASA Astrophysics Data System (ADS)

Bradley, James; Anesio, Alexandre; Arndt, Sandra; Sabacka, Marie; Barker, Gary; Benning, Liane; Blacker, Joshua; Singarayer, Joy; Tranter, Martyn; Yallop, Marian

2016-04-01

Glaciers and ice sheets in Polar and alpine regions are retreating in response to recent climate warming, exposing terrestrial ecosystems that have been locked under the ice for thousands of years. Exposed soils exhibit successional characteristics that can be characterised using a chronosequence approach. Decades of empirical research in glacier forefields has shown that soils are quickly colonised by microbes which drive biogeochemical cycling of elements and affect soil properties including nutrient concentrations, carbon fluxes and soil stability (Bradley et al, 2014). The characterisation of these soils is important for our understanding of the cycling of organic matter under extreme environmental and nutrient limiting conditions, and their potential contribution to global biogeochemical cycles. This is particularly important as these new areas will become more geographically expansive with continued ice retreat. SHIMMER (Soil biogeocHemIcal Model of Microbial Ecosystem Response) (Bradley et al, 2015) is a new mathematical model that simulates biogeochemical and microbial dynamics in glacier forefields. The model captures, explores and predicts the growth of different microbial groups (classified by function), and the associated cycling of carbon, nitrogen and phosphorus along a chronosequence. SHIMMER improves typical soil model formulations by including explicit representation of microbial dynamics, and those processes which are shown to be important for glacier forefields. For example, we categorise microbial groups by function to represent the diversity of soil microbial communities, and include the different metabolic needs and physiological pathways of microbial organisms commonly found in glacier forefields (e.g. microbes derived from underneath the glacier, typical soil bacteria, and microbes that can fix atmospheric nitrogen and assimilate soil nitrogen). Here, we present data from a study where we integrated modelling using SHIMMER with empirical

Multi-Dimensional Voice Program (MDVP) vs Praat for Assessing Euphonic Subjects: A Preliminary Study on the Gender-discriminating Power of Acoustic Analysis Software.

PubMed

Lovato, Andrea; De Colle, Wladimiro; Giacomelli, Luciano; Piacente, Alessandro; Righetto, Lara; Marioni, Gino; de Filippis, Cosimo

2016-11-01

The aim of this study was to compare the discriminatory power of the Multi-Dimensional Voice Program (MDVP) and Praat in distinguishing the gender of euphonic adults. This is a cross-sectional study. The recordings of 100 euphonic volunteers (50 males and 50 females) producing a sustained vowel /a/ were analyzed with MDVP and Praat software. Both computer programs identified significant differences between male and female volunteers in absolute jitter (MDVP P < 0.00001 and Praat P < 0.00001) and in shimmer in decibel (dB) (MDVP P = 0.006 and Praat P = 0.001). Using the scale proposed by Hosmer and Lemeshow, we found no gender discrimination for shimmer in dB with either the MDVP (area under the receiver operating characteristics curve [AUC] = 0.658) or Praat (AUC = 0.682). In our series, on the other hand, MDVP absolute jitter achieved an acceptable discrimination between males and females (AUC = 0.752), and Praat absolute jitter achieved an outstanding discrimination (AUC = 0.901). The discriminatory power of Praat absolute jitter was significantly higher than that of the MDVP (P = 0.003). Absolute jitter sensitivity and specificity were also higher for Praat (83% and 80%) than for the MDVP (74% and 49%). Differences attributable to a subject's gender and to the software used to measure acoustic parameters should be carefully considered in both research and clinical settings. Further studies are needed to test the discriminatory power of different voice analysis programs when differentiating between normal and dysphonic voices. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Fully-Coupled Dynamical Jitter Modeling of Momentum Exchange Devices

NASA Astrophysics Data System (ADS)

Alcorn, John

A primary source of spacecraft jitter is due to mass imbalances within momentum exchange devices (MEDs) used for fine pointing, such as reaction wheels (RWs) and variable-speed control moment gyroscopes (VSCMGs). Although these effects are often characterized through experimentation in order to validate pointing stability requirements, it is of interest to include jitter in a computer simulation of the spacecraft in the early stages of spacecraft development. An estimate of jitter amplitude may be found by modeling MED imbalance torques as external disturbance forces and torques on the spacecraft. In this case, MED mass imbalances are lumped into static and dynamic imbalance parameters, allowing jitter force and torque to be simply proportional to wheel speed squared. A physically realistic dynamic model may be obtained by defining mass imbalances in terms of a wheel center of mass location and inertia tensor. The fully-coupled dynamic model allows for momentum and energy validation of the system. This is often critical when modeling additional complex dynamical behavior such as flexible dynamics and fuel slosh. Furthermore, it is necessary to use the fully-coupled model in instances where the relative mass properties of the spacecraft with respect to the RWs cause the simplified jitter model to be inaccurate. This thesis presents a generalized approach to MED imbalance modeling of a rigid spacecraft hub with N RWs or VSCMGs. A discussion is included to convert from manufacturer specifications of RW imbalances to the parameters introduced within each model. Implementations of the fully-coupled RW and VSCMG models derived within this thesis are released open-source as part of the Basilisk astrodynamics software.

Study of Magnetic Damping Effect on Convection and Solidification Under G-Jitter Conditions

NASA Technical Reports Server (NTRS)

Li, Ben Q.; deGroh, H. C., III

1999-01-01

As shown by NASA resources dedicated to measuring residual gravity (SAMS and OARE systems), g-jitter is a critical issue affecting space experiments on solidification processing of materials. This study aims to provide, through extensive numerical simulations and ground based experiments, an assessment of the use of magnetic fields in combination with microgravity to reduce the g-jitter induced convective flows in space processing systems. We have so far completed asymptotic analyses based on the analytical solutions for g-jitter driven flow and magnetic field damping effects for a simple one-dimensional parallel plate configuration, and developed both 2-D and 3-D numerical models for g-jitter driven flows in simple solidification systems with and without presence of an applied magnetic field. Numerical models have been checked with the analytical solutions and have been applied to simulate the convective flows and mass transfer using both synthetic g-jitter functions and the g-jitter data taken from space flight. Some useful findings have been obtained from the analyses and the modeling results. Some key points may be summarized as follows: (1) the amplitude of the oscillating velocity decreases at a rate inversely proportional to the g-jitter frequency and with an increase in the applied magnetic field; (2) the induced flow approximately oscillates at the same frequency as the affecting g-jitter, but out of a phase angle; (3) the phase angle is a complicated function of geometry, applied magnetic field, temperature gradient and frequency; (4) g-jitter driven flows exhibit a complex fluid flow pattern evolving in time; (5) the damping effect is more effective for low frequency flows; and (6) the applied magnetic field helps to reduce the variation of solutal distribution along the solid-liquid interface. Work in progress includes numerical simulations and ground-based measurements. Both 2-D and 3-D numerical simulations are being continued to obtain further

Reaction Wheel Disturbance Modeling, Jitter Analysis, and Validation Tests for Solar Dynamics Observatory

NASA Technical Reports Server (NTRS)

Liu,Kuo-Chia; Maghami, Peiman; Blaurock, Carl

2008-01-01

The Solar Dynamics Observatory (SDO) aims to study the Sun's influence on the Earth by understanding the source, storage, and release of the solar energy, and the interior structure of the Sun. During science observations, the jitter stability at the instrument focal plane must be maintained to less than a fraction of an arcsecond for two of the SDO instruments. To meet these stringent requirements, a significant amount of analysis and test effort has been devoted to predicting the jitter induced from various disturbance sources. One of the largest disturbance sources onboard is the reaction wheel. This paper presents the SDO approach on reaction wheel disturbance modeling and jitter analysis. It describes the verification and calibration of the disturbance model, and ground tests performed for validating the reaction wheel jitter analysis. To mitigate the reaction wheel disturbance effects, the wheels will be limited to operate at low wheel speeds based on the current analysis. An on-orbit jitter test algorithm is also presented in the paper which will identify the true wheel speed limits in order to ensure that the wheel jitter requirements are met.

A low timing jitter picosecond microchip laser pumped by pulsed LD

NASA Astrophysics Data System (ADS)

Wang, Sha; Wang, Yan-biao; Feng, Guoying; Zhou, Shou-huan

2016-07-01

SESAM passively Q-switched microchip laser is a very promising instrument to replace mode locked lasers to obtain picosecond pulses. The biggest drawback of a passively Q-switched microchip laser is its un-avoided large timing jitter, especially when the pump intensity is low, i.e. at low laser repetition rate range. In order to obtain a low timing jitter passively Q-switched picosecond microchip laser in the whole laser repetition rate range, a 1000 kHz pulsed narrow bandwidth Fiber Bragg Grating (FBG) stablized laser diode was used as the pump source. By tuning the pump intensity, we could control the output laser frequency. In this way, we achieved a very low timing jitter passively Q-switched picosecond laser at 2.13 mW, 111.1 kHz. The relative timing jitter was only 0.0315%, which was around 100 times smaller compared with a cw LD pumped microchip working at hundred kilohertz repetition rate frequency range.

Measuring the jitter of ring oscillators by means of information theory quantifiers

NASA Astrophysics Data System (ADS)

Antonelli, M.; De Micco, L.; Larrondo, H. A.

2017-02-01

Ring oscillators (RO's) are elementary blocks widely used in digital design. Jitter is unavoidable in RO's, its presence is an undesired behavior in many applications, as clock generators. On the contrary, jitter may be used as the noise source in RO-based true-random numbers generators (TRNG). Consequently, jitter measure is a relevant issue to characterize a RO, and it is the subject of this paper. The main contribution is the use of Information Theory Quantifiers (ITQ) as measures of RO's jitter. It is shown that among several ITQ evaluated, two of them emerge as good measures because they are independent of parameters used for their statistical determination. They turned out to be robust and may be implemented experimentally. We encountered that a dual entropy plane allows a visual comparison of results.

Reference-free, high-resolution measurement method of timing jitter spectra of optical frequency combs

PubMed Central

Kwon, Dohyeon; Jeon, Chan-Gi; Shin, Junho; Heo, Myoung-Sun; Park, Sang Eon; Song, Youjian; Kim, Jungwon

2017-01-01

Timing jitter is one of the most important properties of femtosecond mode-locked lasers and optical frequency combs. Accurate measurement of timing jitter power spectral density (PSD) is a critical prerequisite for optimizing overall noise performance and further advancing comb applications both in the time and frequency domains. Commonly used jitter measurement methods require a reference mode-locked laser with timing jitter similar to or lower than that of the laser-under-test, which is a demanding requirement for many laser laboratories, and/or have limited measurement resolution. Here we show a high-resolution and reference-source-free measurement method of timing jitter spectra of optical frequency combs using an optical fibre delay line and optical carrier interference. The demonstrated method works well for both mode-locked oscillators and supercontinua, with 2 × 10−9 fs2/Hz (equivalent to −174 dBc/Hz at 10-GHz carrier frequency) measurement noise floor. The demonstrated method can serve as a simple and powerful characterization tool for timing jitter PSDs of various comb sources including mode-locked oscillators, supercontinua and recently emerging Kerr-frequency combs; the jitter measurement results enabled by our method will provide new insights for understanding and optimizing timing noise in such comb sources. PMID:28102352

Finite Element Analysis of Magnetic Damping Effects on G-Jitter Induced Fluid Flow

NASA Technical Reports Server (NTRS)

Pan, Bo; Li, Ben Q.; deGroh, Henry C., III

1997-01-01

This paper reports some interim results on numerical modeling and analyses of magnetic damping of g-jitter driven fluid flow in microgravity. A finite element model is developed to represent the fluid flow, thermal and solute transport phenomena in a 2-D cavity under g-jitter conditions with and without an applied magnetic field. The numerical model is checked by comparing with analytical solutions obtained for a simple parallel plate channel flow driven by g-jitter in a transverse magnetic field. The model is then applied to study the effect of steady state g-jitter induced oscillation and on the solute redistribution in the liquid that bears direct relevance to the Bridgman-Stockbarger single crystal growth processes. A selection of computed results is presented and the results indicate that an applied magnetic field can effectively damp the velocity caused by g-jitter and help to reduce the time variation of solute redistribution.

Practical security analysis of continuous-variable quantum key distribution with jitter in clock synchronization

NASA Astrophysics Data System (ADS)

Xie, Cailang; Guo, Ying; Liao, Qin; Zhao, Wei; Huang, Duan; Zhang, Ling; Zeng, Guihua

2018-03-01

How to narrow the gap of security between theory and practice has been a notoriously urgent problem in quantum cryptography. Here, we analyze and provide experimental evidence of the clock jitter effect on the practical continuous-variable quantum key distribution (CV-QKD) system. The clock jitter is a random noise which exists permanently in the clock synchronization in the practical CV-QKD system, it may compromise the system security because of its impact on data sampling and parameters estimation. In particular, the practical security of CV-QKD with different clock jitter against collective attack is analyzed theoretically based on different repetition frequencies, the numerical simulations indicate that the clock jitter has more impact on a high-speed scenario. Furthermore, a simplified experiment is designed to investigate the influence of the clock jitter.

Automatic Assessment of Acoustic Parameters of the Singing Voice: Application to Professional Western Operatic and Jazz Singers.

PubMed

Manfredi, Claudia; Barbagallo, Davide; Baracca, Giovanna; Orlandi, Silvia; Bandini, Andrea; Dejonckere, Philippe H

2015-07-01

The obvious perceptual differences between various singing styles like Western operatic and jazz rely on specific dissimilarities in vocal technique. The present study focuses on differences in vibrato acoustics and in singer's formant as analyzed by a novel software tool, named BioVoice, based on robust high-resolution and adaptive techniques that have proven its validity on synthetic voice signals. A total of 48 professional singers were investigated (29 females; 19 males; 29 Western operatic; and 19 jazz). They were asked to sing "a cappella," but with artistic expression, a well-known musical phrase from Gershwin's Porgy and Bess, in their own style: either operatic or jazz. A specific sustained note was extracted for detailed vibrato analysis. Beside rate (s(-1)) and extent (cents), duration (seconds) and regularity were computed. Two new concepts are introduced: vibrato jitter and vibrato shimmer, by analogy with the traditional jitter and shimmer of voice signals. For the singer's formant, on the same sustained tone, the ratio of the acoustic energy in formants 1-2 to the energy in formants 3, 4, and 5 was automatically computed, providing a quality ratio (QR). Vibrato rates did not differ among groups. Extent was significantly larger in operatic singers, particularly females. Vibrato jitter and vibrato shimmer were significantly smaller in operatic singers. Duration of vibrato was also significantly longer in operatic singers. QR was significantly lower in male operatic singers. Some vibrato characteristics (extent, regularity, and duration) very clearly differentiate the Western operatic singing style from the jazz singing style. The singer's formant is typical of male operatic singers. The new software tool is well suited to provide useful feedback in a pedagogical context. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Period for Normalization of Voice Acoustic Parameters in Indian Pediatric Cochlear Implantees.

PubMed

Joy, Jeena V; Deshpande, Shweta; Vaid, Dr Neelam

2017-05-01

The purpose of this study was to investigate the duration required by children with cochlear implants to approximate the norms of voice acoustic parameters. The study design is retrospective. Thirty children with cochlear implants (chronological ages ranging between 4.1 and 6.7 years) were divided into three groups, based on the postimplantation duration. Ten normal-hearing children (chronological ages ranging between 4 and 7 years) were selected as the control group. All implanted children underwent an objective voice analysis using Dr. Speech software (Tiger DRS, Inc., Seattle, WA, USA) at 6 months and at 1 and 2 years of implant use. Voice analysis was done for the children in the control group and means were derived for all the parameters analyzed to obtain the normal values. Habitual fundamental frequency (HFF), jitter (frequency variation), and shimmer (amplitude variation) were the voice acoustic parameters analyzed for the vowels |a|, |i|, and |u|. The obtained values of these parameters were then compared with the norms. HFF for the children with implant use for 6 months and 1 year did significantly differ from the control group. However, there was no significant difference (P > 0.5) observed in the children with implant use for 2 years, thus matching the norms. Jitter and shimmer showed a significant difference (P < 0.5) even at 2 years of implant use when compared with the control group. The findings of the study divulge that children with cochlear implants approximate age-matched normal-hearing kids with respect to the voice acoustic parameter of HFF by 2 years of implant use. However, jitter and shimmer were not found to stabilize for the duration studied. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Non-invasive algorithm for bowel motility estimation using a back-propagation neural network model of bowel sounds.

PubMed

Kim, Keo-Sik; Seo, Jeong-Hwan; Song, Chul-Gyu

2011-08-10

Radiological scoring methods such as colon transit time (CTT) have been widely used for the assessment of bowel motility. However, these radiograph-based methods need cumbersome radiological instruments and their frequent exposure to radiation. Therefore, a non-invasive estimation algorithm of bowel motility, based on a back-propagation neural network (BPNN) model of bowel sounds (BS) obtained by an auscultation, was devised. Twelve healthy males (age: 24.8 ± 2.7 years) and 6 patients with spinal cord injury (6 males, age: 55.3 ± 7.1 years) were examined. BS signals generated during the digestive process were recorded from 3 colonic segments (ascending, descending and sigmoid colon), and then, the acoustical features (jitter and shimmer) of the individual BS segment were obtained. Only 6 features (J1, 3, J3, 3, S1, 2, S2, 1, S2, 2, S3, 2), which are highly correlated to the CTTs measured by the conventional method, were used as the features of the input vector for the BPNN. As a results, both the jitters and shimmers of the normal subjects were relatively higher than those of the patients, whereas the CTTs of the normal subjects were relatively lower than those of the patients (p < 0.01). Also, through k-fold cross validation, the correlation coefficient and mean average error between the CTTs measured by a conventional radiograph and the values estimated by our algorithm were 0.89 and 10.6 hours, respectively. The jitter and shimmer of the BS signals generated during the peristalsis could be clinically useful for the discriminative parameters of bowel motility. Also, the devised algorithm showed good potential for the continuous monitoring and estimation of bowel motility, instead of conventional radiography, and thus, it could be used as a complementary tool for the non-invasive measurement of bowel motility.

Coupled Optoelectronic Oscillators:. Application to Low-Jitter Pulse Generation

NASA Astrophysics Data System (ADS)

Yu, N.; Tu, M.; Maleki, L.

2002-04-01

Actively mode-locked Erbium-doped fiber lasers (EDFL) have been studied for generating stable ultra-fast pulses (< 2 ps) at high repetition rates (> 5 GHz) [1,2]. These devices can be compact and environmentally stable, quite suitable for fiber-based high-data-rate communications and optical ultra-fast analog-to-digital conversions (ADC) [3]. The pulse-to-pulse jitter of an EDFL-based pulse generator will be ultimately limited by the phase noise of the mode-locking microwave source (typically electronic frequency synthesizers). On the other hand, opto-electronic oscillators (OEO) using fibers have been demonstrated to generate ultra-low phase noise microwaves at 10 GHz and higher [4]. The overall phase noise of an OEO can be much lower than commercially available synthesizers at the offset-frequency range above 100 Hz. Clearly, ultra-low jitter pulses can be generated by taking advantage of the low phase noise of OEOs. In this paper, we report the progress in developing a new low-jitter pulse generator by combing the two technologies. In our approach, the optical oscillator (mode-locked EDFL) and the microwave oscillator (OEO) are coupled through a common Mach-Zehnder (MZ) modulator, thus named coupled opto-electronic oscillator (COEO) [5]. Based on the results of previous OEO study, we can expect a 10 GHz pulse train with jitters less than 10 fs.

Acoustic Correlates of Compensatory Adjustments to the Glottic and Supraglottic Structures in Patients with Unilateral Vocal Fold Paralysis

PubMed Central

2015-01-01

The goal of this study was to analyse perceptually and acoustically the voices of patients with Unilateral Vocal Fold Paralysis (UVFP) and compare them to the voices of normal subjects. These voices were analysed perceptually with the GRBAS scale and acoustically using the following parameters: mean fundamental frequency (F0), standard-deviation of F0, jitter (ppq5), shimmer (apq11), mean harmonics-to-noise ratio (HNR), mean first (F1) and second (F2) formants frequency, and standard-deviation of F1 and F2 frequencies. Statistically significant differences were found in all of the perceptual parameters. Also the jitter, shimmer, HNR, standard-deviation of F0, and standard-deviation of the frequency of F2 were statistically different between groups, for both genders. In the male data differences were also found in F1 and F2 frequencies values and in the standard-deviation of the frequency of F1. This study allowed the documentation of the alterations resulting from UVFP and addressed the exploration of parameters with limited information for this pathology. PMID:26557690

Radial Velocities of Subgiant Stars and New Astrophysical Insights into RV Jitter

NASA Astrophysics Data System (ADS)

Luhn, Jacob; Bastien, Fabienne; Wright, Jason T.

2018-01-01

For nearly 20 years, the California Planet Search (CPS) has simultaneously monitored precise radial velocities and chromospheric activity levels of stars from Keck observatory to search for exoplanets. This sample provides a useful set of stars to better determine the dependence of RV jitter on flicker (which traces surface gravity) first shown in Bastien et al. (2014). We expand upon this initial work by examining a much larger sample of stars covering a much wider range of stellar parameters (effective temperature, surface gravity, and activity, among others). For more than 600 stars, there are enough RV measurements to distinguish this astrophysical jitter from accelerations due to orbital companions. To properly isolate RV jitter from these effects, we must first remove the RV signal due to these companions, including several previously unannounced giant planets around subgiant stars. We highlight some new results from our analysis of the CPS data. A more thorough understanding of the various sources of RV jitter and the underlying stellar phenomena that drive these intrinsic RV variations will enable more precise jitter estimates for RV follow-up targets such as those from K2 or the upcoming TESS mission.

Sub-femtosecond timing jitter, all-fiber, CNT-mode-locked Er-laser at telecom wavelength.

PubMed

Kim, Chur; Bae, Sangho; Kieu, Khanh; Kim, Jungwon

2013-11-04

We demonstrate a 490-attosecond timing jitter (integration bandwidth: 10 kHz - 39.4 MHz) optical pulse train from a 78.7-MHz repetition rate, all-fiber soliton Er laser mode-locked by a fiber tapered carbon nanotube saturable absorber (ft-CNT-SA). To achieve this jitter performance, we searched for a net cavity dispersion condition where the Gordon-Haus jitter is minimized while maintaining stable soliton mode-locking. Our result shows that optical pulse trains with well below a femtosecond timing jitter can be generated from a self-starting and robust all-fiber laser operating at telecom wavelength.

A low jitter PLL clock used for phase change memory

NASA Astrophysics Data System (ADS)

Xiao, Hong; Houpeng, Chen; Zhitang, Song; Daolin, Cai; Xi, Li

2013-02-01

A fully integrated low-jitter, precise frequency CMOS phase-locked loop (PLL) clock for the phase change memory (PCM) drive circuit is presented. The design consists of a dynamic dual-reset phase frequency detector (PFD) with high frequency acquisition, a novel low jitter charge pump, a CMOS ring oscillator based voltage-controlled oscillator (VCO), a 2nd order passive loop filter, and a digital frequency divider. The design is fabricated in 0.35 μm CMOS technology and consumes 20 mW from a supply voltage of 5 V. In terms of the PCM's program operation requirement, the output frequency range is from 1 to 140 MHz. For the 140 MHz output frequency, the circuit features a cycle-to-cycle jitter of 28 ps RMS and 250 ps peak-to-peak.

Study of Magnetic Damping Effect on Convection and Solidification Under G-Jitter Conditions

NASA Technical Reports Server (NTRS)

Li, Ben Q.; deGroh, H. C.

2001-01-01

As shown in space flight experiments, g-jitter is a critical issue affecting solidification processing of materials in microgravity. This study aims to provide, through extensive numerical simulations and ground based experiments, an assessment of the use of magnetic fields in combination with microgravity to reduce the g-jitter induced convective flows in space processing systems. Analytical solutions and 2-D and 3-D numerical models for g-jitter driven flows in simple solidification systems with and without the presence of an applied magnetic field have been developed and extensive analyses were carried out. A physical model was also constructed and PIV measurements compared reasonably well with predictions from numerical models. Some key points may be summarized as follows: (1) the amplitude of the oscillating velocity decreases at a rate inversely proportional to the g-jitter frequency and with an increase in the applied magnetic field; (2) the induced flow oscillates at approximately the same frequency as the affecting g-jitter, but out of a phase angle; (3) the phase angle is a complicated function of geometry, applied magnetic field, temperature gradient and frequency; (4) g-jitter driven flows exhibit a complex fluid flow pattern evolving in time; (5) the damping effect is more effective for low frequency flows; and (6) the applied magnetic field helps to reduce the variation of solutal distribution along the solid-liquid interface. Work in progress includes developing numerical models for solidification phenomena with the presence of both g-jitter and magnetic fields and developing a ground-based physical model to verify numerical predictions.

Quantitating Changes in Jitter and Spike Number Using Concentric Needle Electrodes in Amyotrophic Lateral Sclerosis Patients

PubMed Central

Liu, Ming-Sheng; Niu, Jing-Wen; Li, Yi; Guan, Yu-Zhou; Cui, Li-Ying

2016-01-01

Background: Single-fiber electromyography (SFEMG) has been suggested as a quantitative method for supporting chronic partial denervation in amyotrophic lateral sclerosis (ALS) by the revised EI Escorial criteria. Although concentric needle (CN) electrodes have been used to assess jitter in myasthenia gravis patients and healthy controls, there are few reports using CN electrodes to assess motor unit instability and denervation in neurogenic diseases. The aim of this study was to determine whether quantitative changes in jitter and spike number using CN electrodes could be used for ALS studies. Methods: Twenty-seven healthy controls and 23 ALS patients were studied using both CN and single-fiber needle (SFN) electrodes on the extensor digitorum communis muscle with an SFEMG program. The SFN-jitter and SFN-fiber density data were measured using SFN electrodes. The CN-jitter and spike number were measured using CN electrodes. Results: The mean CN-jitter was significantly increased in ALS patients (47.3 ± 17.0 μs) than in healthy controls (27.4 ± 3.3 μs) (P < 0.001). Besides, the mean spike number was significantly increased in ALS patients (2.5 ± 0.5) than in healthy controls (1.7 ± 0.3) (P < 0.001). The sensitivity and specificity in the diagnosis of ALS were 82.6% and 92.6% for CN-jitter (cut-off value: 32 μs), and 91.3% and 96.3% for the spike number (cut-off value: 2.0), respectively. There was no significant difference between the SFN-jitter and CN-jitter in ALS patients; meanwhile, there was no significant difference between the SFN-jitter and CN-jitter in healthy controls. Conclusion: CN-jitter and spike number could be used to quantitatively evaluate changes due to denervation-reinnervation in ALS. PMID:27098787

Jitter and phase noise of ADPLL due to PSN with deterministic frequency

NASA Astrophysics Data System (ADS)

Deng, Xiaoying; Yang, Jun; Wu, Jianhui

2011-09-01

In this article, jitter and phase noise of all-digital phase-locked loop due to power supply noise (PSN) with deterministic frequency are analysed. It leads to the conclusion that jitter and phase noise heavily depend on the noise frequency. Compared with jitter, phase noise is much less affected by the deterministic PSN. Our method is utilised to study a CMOS ADPLL designed and simulated in SMIC 0.13 µm standard CMOS process. A comparison between the results obtained by our method and those obtained by simulation and measurement proves the accuracy of the predicted model. When the digital controlled oscillator was corrupted by PSN with 100 mVpk-pk, the measured jitters were 33.9 ps at the rate of fG = 192 MHz and 148.5 ps at the rate of fG = 40 MHz. However, the measured phase noise was exactly the same except for two impulses appearing at 192 and 40 MHz, respectively.

[Observation of the dysphonia severity index in evaluating curative effect of vocal cord polyp surgery].

PubMed

Zhou, Zhou; Ge, Pingjiang; Liu, Qian; Liu, Ming; Zhang, Wei

2015-08-01

To investigate the applicability of the eysphonia severity index (DSI) in evaluating effects of surgery between before and after groups of vocal polyp patients. Analyses of measurement data pre and pro-surgery of 70 vocal polyp patients and 35 no voice disorders volunteers (control group). The voice quality was measured subjectively with the voice handicap index (VHI), the GRBAS and fiber electronic laryngoscopy. Measures of maximum phonation time (MPT), shimmer and jitter were obtained for each subject by using DiVAS 2.30 (XION, Germany). The DiVAS 2.30 had spotanenously calculate the scores of DSI. Using SPSS 17.0 to find the differences of DSI scores among the three groups by one-way ANOVA variance analysis. And finding out of the correlation with DSI scores and VHI scores, GRBAS, MPT, jitter and shimmer. DSI improved significantly after surgery in the vocal polyps group (mean difference DSI -2.92 and 1.87, respectively) and also in the control group (mean difference DSI -2.92 and 2.30, respectively). However, no significant difference between the control group and the after surgery group. By using Pearson correlation analysis, this study observed a strong correlation between the DSI scores and the VHI scores, the values of GRBAS, shimmer (P < 0.01). DSI is an effective and high accuracy multi-parameter system for evaluation of vocal cord polyp patients as an independent assessment of dysphonia. DSI also can be used in evaluation of the effects of the vocal polyps surgery.

Real-time operating system timing jitter and its impact on motor control

NASA Astrophysics Data System (ADS)

Proctor, Frederick M.; Shackleford, William P.

2001-12-01

General-purpose microprocessors are increasingly being used for control applications due to their widespread availability and software support for non-control functions like networking and operator interfaces. Two classes of real-time operating systems (RTOS) exist for these systems. The traditional RTOS serves as the sole operating system, and provides all OS services. Examples include ETS, LynxOS, QNX, Windows CE and VxWorks. RTOS extensions add real-time scheduling capabilities to non-real-time OSes, and provide minimal services needed for the time-critical portions of an application. Examples include RTAI and RTL for Linux, and HyperKernel, OnTime and RTX for Windows NT. Timing jitter is an issue in these systems, due to hardware effects such as bus locking, caches and pipelines, and software effects from mutual exclusion resource locks, non-preemtible critical sections, disabled interrupts, and multiple code paths in the scheduler. Jitter is typically on the order of a microsecond to a few tens of microseconds for hard real-time operating systems, and ranges from milliseconds to seconds in the worst case for soft real-time operating systems. The question of its significance on the performance of a controller arises. Naturally, the smaller the scheduling period required for a control task, the more significant is the impact of timing jitter. Aside from this intuitive relationship is the greater significance of timing on open-loop control, such as for stepper motors, than for closed-loop control, such as for servo motors. Techniques for measuring timing jitter are discussed, and comparisons between various platforms are presented. Techniques to reduce jitter or mitigate its effects are presented. The impact of jitter on stepper motor control is analyzed.

Correlation Between Acoustic Measurements and Self-Reported Voice Disorders Among Female Teachers.

PubMed

Lin, Feng-Chuan; Chen, Sheng Hwa; Chen, Su-Chiu; Wang, Chi-Te; Kuo, Yu-Ching

2016-07-01

Many studies focused on teachers' voice problems and most of them were conducted using questionnaires, whereas little research has investigated the relationship between self-reported voice disorders and objective quantification of voice. This study intends to explore the relationship of acoustic measurements according to self-reported symptoms and its predictive value of future dysphonia. This is a case-control study. Voice samples of 80 female teachers were analyzed, including 40 self-reported voice disorders (VD) and 40 self-reported normal voice (NVD) subjects. The acoustic measurements included jitter, shimmer, and noise-to-harmonics ratio (NHR). Levene's t test and logistic regression were used to analyze the differences between VD and NVD and the relationship between self-reported voice conditions and the acoustic measurements. To examine whether acoustic measurements can be used to predict further voice disorders, we applied a receiver operating characteristic (ROC) curve to determine the cutoff values and the associated sensitivity and specificity. The results showed that jitter, shimmer, and the NHR of VD were significantly higher than those of NVD. Among the parameters, the NHR and shimmer demonstrated the highest correlation with self-reported voice disorders. By using the NHR ≥0.138 and shimmer ≥0.470 dB as the cutoff values, the ROC curve displayed 72.5% of sensitivity and 75% of specificity, and the overall positive predictive value for subsequent dysphonia achieved 60%. This study demonstrated a significant correlation between acoustic measurements and self-reported dysphonic symptoms. NHR and ShdB are two acoustic parameters that are more able to reflect vocal abnormalities and, probably, to predict subsequent subjective voice disorder. Future research recruiting more subjects in other occupations and genders shall validate the preliminary results revealed in this study. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All

Measurement Techniques for Transmit Source Clock Jitter for Weak Serial RF Links

NASA Technical Reports Server (NTRS)

Lansdowne, Chatwin A.; Schlesinger, Adam M.

2010-01-01

Techniques for filtering clock jitter measurements are developed, in the context of controlling data modulation jitter on an RF carrier to accommodate low signal-to-noise ratio thresholds of high-performance error correction codes. Measurement artifacts from sampling are considered, and a tutorial on interpretation of direct readings is included.

Passive isolator design for jitter reduction in the Terrestrial Planet Finder Coronagraph

NASA Technical Reports Server (NTRS)

Blaurock, Carl; Liu, Kuo-Chia; Dewell, Larry; Alexander, James

2005-01-01

Terrestrial Planet Finder (TPF) is a mission to locate and study extrasolar Earth-like planets. The TPF Coronagraph (TPF-C), planned for launch in the latter half of the next decade, will use a coronagraphic mask and other optics to suppress the light of the nearby star in order to collect visible light from such planets. The required contrast ratio of 5e-11 can only be achieved by maintaining pointing accuracy to 4 milli-arcseconds, and limiting optics jitter to below 5 nm. Numerous mechanical disturbances act to induce jitter. This paper concentrates on passive isolation techniques to minimize the optical degradation introduced by disturbance sources. A passive isolation system, using compliant mounts placed at an energy bottleneck to reduce energy transmission above a certain frequency, is a low risk, flight proven design approach. However, the attenuation is limited, compared to an active system, so the feasibility of the design must be demonstrated by analysis. The paper presents the jitter analysis for the baseline TPF design, using a passive isolation system. The analysis model representing the dynamics of the spacecraft and telescope is described, with emphasis on passive isolator modeling. Pointing and deformation metrics, consistent with the TPF-C error budget, are derived. Jitter prediction methodology and results are presented. Then an analysis of the critical design parameters that drive the TPF-C jitter response is performed.

The Role of Perceived Speed in Vection: Does Perceived Speed Modulate the Jitter and Oscillation Advantages?

PubMed Central

Apthorp, Deborah; Palmisano, Stephen

2014-01-01

Illusory self-motion (‘vection’) in depth is strongly enhanced when horizontal/vertical simulated viewpoint oscillation is added to optic flow inducing displays; a similar effect is found for simulated viewpoint jitter. The underlying cause of these oscillation and jitter advantages for vection is still unknown. Here we investigate the possibility that perceived speed of motion in depth (MID) plays a role. First, in a 2AFC procedure, we obtained MID speed PSEs for briefly presented (vertically oscillating and smooth) radial flow displays. Then we examined the strength, duration and onset latency of vection induced by oscillating and smooth radial flow displays matched either for simulated or perceived MID speed. The oscillation advantage was eliminated when displays were matched for perceived MID speed. However, when we tested the jitter advantage in the same manner, jittering displays were found to produce greater vection in depth than speed-matched controls. In summary, jitter and oscillation advantages were the same across experiments, but slower MID speed was required to match jittering than oscillating stimuli. Thus, to the extent that vection is driven by perceived speed of MID, this effect is greater for oscillating than for jittering stimuli, which suggests that the two effects may arise from separate mechanisms. PMID:24651861

An Experimental Study of a Low-Jitter Pulsed Electromagnetic Plasma Accelerator

NASA Technical Reports Server (NTRS)

Thio, Y. C. Francis; Lee, Michael; Eskridge, Richard; Smith, James; Martin, Adam; Rodgers, Stephen L. (Technical Monitor)

2001-01-01

An experimental plasma accelerator for a variety of applications under development at the NASA Marshall Space Flight Center is described. The accelerator is a pulsed plasma thruster and has been tested experimentally and plasma jet velocities of approximately 50 kilometers per second have been obtained. The plasma jet structure has been photographed with 10 ns exposure times to reveal a stable and repeatable plasma structure. Data for velocity profile information has been obtained using light pipes embedded in the gun walls to record the plasma transit at various barrel locations. Preliminary spatially resolved spectral data and magnetic field probe data are also presented. A high speed triggering system has been developed and tested as a means of reducing the gun "jitter". This jitter has been characterized and future work for second generation "ultra-low jitter" gun development is identified.

Photonic ADC: overcoming the bottleneck of electronic jitter.

PubMed

Khilo, Anatol; Spector, Steven J; Grein, Matthew E; Nejadmalayeri, Amir H; Holzwarth, Charles W; Sander, Michelle Y; Dahlem, Marcus S; Peng, Michael Y; Geis, Michael W; DiLello, Nicole A; Yoon, Jung U; Motamedi, Ali; Orcutt, Jason S; Wang, Jade P; Sorace-Agaskar, Cheryl M; Popović, Miloš A; Sun, Jie; Zhou, Gui-Rong; Byun, Hyunil; Chen, Jian; Hoyt, Judy L; Smith, Henry I; Ram, Rajeev J; Perrott, Michael; Lyszczarz, Theodore M; Ippen, Erich P; Kärtner, Franz X

2012-02-13

Accurate conversion of wideband multi-GHz analog signals into the digital domain has long been a target of analog-to-digital converter (ADC) developers, driven by applications in radar systems, software radio, medical imaging, and communication systems. Aperture jitter has been a major bottleneck on the way towards higher speeds and better accuracy. Photonic ADCs, which perform sampling using ultra-stable optical pulse trains generated by mode-locked lasers, have been investigated for many years as a promising approach to overcome the jitter problem and bring ADC performance to new levels. This work demonstrates that the photonic approach can deliver on its promise by digitizing a 41 GHz signal with 7.0 effective bits using a photonic ADC built from discrete components. This accuracy corresponds to a timing jitter of 15 fs - a 4-5 times improvement over the performance of the best electronic ADCs which exist today. On the way towards an integrated photonic ADC, a silicon photonic chip with core photonic components was fabricated and used to digitize a 10 GHz signal with 3.5 effective bits. In these experiments, two wavelength channels were implemented, providing the overall sampling rate of 2.1 GSa/s. To show that photonic ADCs with larger channel counts are possible, a dual 20-channel silicon filter bank has been demonstrated.

The Effect of Microphone Type on Acoustical Measures of Synthesized Vowels.

PubMed

Kisenwether, Jessica Sofranko; Sataloff, Robert T

2015-09-01

The purpose of this study was to compare microphones of different directionality, transducer type, and cost, with attention to their effects on acoustical measurements of period perturbation, amplitude perturbation, and noise using synthesized sustained vowel samples. This was a repeated measures design. Synthesized sustained vowel stimuli (with known acoustic characteristics and systematic changes in jitter, shimmer, and noise-to-harmonics ratio) were recorded by a variety of dynamic and condenser microphones. Files were then analyzed for mean fundamental frequency (fo), fo standard deviation, absolute jitter, shimmer in dB, peak-to-peak amplitude variation, and noise-to-harmonics ratio. Acoustical measures following recording were compared with the synthesized, known acoustical measures before recording. Although informal analyses showed some differences among microphones, and analyses of variance showed that type of microphone is a significant predictor, t-tests revealed that none of the microphones generated different means compared with the generated acoustical measures. In this sample, microphone type, directionality, and cost did not have a significant effect on the validity of acoustic measures. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Chaos tool implementation for non-singer and singer voice comparison (preliminary study)

NASA Astrophysics Data System (ADS)

Dajer, Me; Pereira, Jc; Maciel, Cd

2007-11-01

Voice waveform is linked to the stretch, shorten, widen or constrict vocal tract. The articulation effects of the singer's vocal tract modify the voice acoustical characteristics and differ from the non-singer voices. In the last decades, Chaos Theory has shown the possibility to explore the dynamic nature of voice signals from a different point of view. The purpose of this paper is to apply the chaos technique of phase space reconstruction to analyze non- singers and singer voices in order to explore the signal nonlinear dynamic, and correlate them with traditional acoustic parameters. Eight voice samples of sustained vowel /i/ from non-singers and eight from singers were analyzed with "ANL" software. The samples were also acoustically analyzed with "Analise de Voz 5.0" in order to extract acoustic perturbation measures jitter and shimmer, and the coefficient of excess - (EX). The results showed different visual patterns for the two groups correlated with different jitter, shimmer, and coefficient of excess values. We conclude that these results clearly indicate the potential of phase space reconstruction technique for analysis and comparison of non-singers and singer voices. They also show a promising tool for training voices application.

Analysis of Optimal Jitter Buffer Size for VoIP QoS under WiMAX Power-Saving Mode

NASA Astrophysics Data System (ADS)

Kim, Hyungsuk; Kim, Taehyoun

VoIP service is expected as one of the key applications of Mobile WiMAX, but the speech quality of VoIP service often suffers deterioration due to the fluctuating transmission delay called jitter. This is commonly ameliorated by a de-jitter buffer, and we aim to find the optimal size of de-jitter buffer to achieve speech quality comparable to PSTN. We developed a new model of the packet drops at the de-jitter buffer and the end-to-end packet delay which takes account of the additional delay introduced by the WiMAX power-saving mode. Using our model, we analyzed the optimal size of the de-jitter buffer for various network parameters, and showed that the results obtained by analysis accord with simulation results.

Light gas gun with reduced timing jitter

DOEpatents

Laabs, Gary W.; Funk, David J.; Asay, Blaine W.

1998-01-01

Gas gun with reduced timing jitter. A gas gun having a prepressurized projectile held in place with a glass rod in compression is described. The glass rod is destroyed with an explosive at a precise time which allows a restraining pin to be moved and free the projectile.

Broadly tunable, low timing jitter, high repetition rate optoelectronic comb generator

PubMed Central

Metcalf, A. J.; Quinlan, F.; Fortier, T. M.; Diddams, S. A.; Weiner, A. M.

2016-01-01

We investigate the low timing jitter properties of a tunable single-pass optoelectronic frequency comb generator. The scheme is flexible in that both the repetition rate and center frequency can be continuously tuned. When operated with 10 GHz comb spacing, the integrated residual pulse-to-pulse timing jitter is 11.35 fs (1 Hz to 10 MHz) with no feedback stabilization. The corresponding phase noise at 1 Hz offset from the photodetected 10 GHz carrier is −100 dBc/Hz. PMID:26865734

Effects of G-Jitter on Interfacial Dynamics of Two Miscible Liquids: Application of MIM

NASA Technical Reports Server (NTRS)

Duval, Walter M. B.; Tryggvason, Bjarni V.

2000-01-01

We designed an experiment to examine the effects of g-jitter on mixing of two miscible liquids using the Microgravity Vibration Isolation Mount (MIM). The global bifurcation of the interface was observed with the MIM operating alternatively to either transmit the g-jitter, isolate from the g-jitter or to provide controlled vibration levels with well defined amplitude and frequency content. With the MIM in isolation mode, the interface remains stationary indicating buoyancy induced convection is negligibly small such that mixing occurs via intrinsic mass diffusion without the masking effect of vibration driven convection. Analytical and computational results are in agreement with the experimental findings. Operation of the MIM in forced mode with conditions typical of g-jitter shows that vibration induced convective flows can excite instability mechanisms such as Kelvin-Helmholtz to generate large amplitude quasi-stationary waves oriented vertically for various cases with Stokes-Reynolds number in the range of 0.003 to 0.5. The two and four mode quasi-stationary waves are also predicted with a mathematical model. Though unplanned, the effect of a primary thruster filing was captured and shown to cause a catastrophic bifurcation, enhancing local mass transport. In light of the findings, experiments planned for the International Space Station should consider the potential effects of g-jitter.

Light gas gun with reduced timing jitter

DOEpatents

Laabs, G.W.; Funk, D.J.; Asay, B.W.

1998-06-09

Gas gun with reduced timing jitter is disclosed. A gas gun having a prepressurized projectile held in place with a glass rod in compression is described. The glass rod is destroyed with an explosive at a precise time which allows a restraining pin to be moved and free the projectile. 4 figs.

Influence of P300 latency jitter on event related potential-based brain-computer interface performance

NASA Astrophysics Data System (ADS)

Aricò, P.; Aloise, F.; Schettini, F.; Salinari, S.; Mattia, D.; Cincotti, F.

2014-06-01

Objective. Several ERP-based brain-computer interfaces (BCIs) that can be controlled even without eye movements (covert attention) have been recently proposed. However, when compared to similar systems based on overt attention, they displayed significantly lower accuracy. In the current interpretation, this is ascribed to the absence of the contribution of short-latency visual evoked potentials (VEPs) in the tasks performed in the covert attention modality. This study aims to investigate if this decrement (i) is fully explained by the lack of VEP contribution to the classification accuracy; (ii) correlates with lower temporal stability of the single-trial P300 potentials elicited in the covert attention modality. Approach. We evaluated the latency jitter of P300 evoked potentials in three BCI interfaces exploiting either overt or covert attention modalities in 20 healthy subjects. The effect of attention modality on the P300 jitter, and the relative contribution of VEPs and P300 jitter to the classification accuracy have been analyzed. Main results. The P300 jitter is higher when the BCI is controlled in covert attention. Classification accuracy negatively correlates with jitter. Even disregarding short-latency VEPs, overt-attention BCI yields better accuracy than covert. When the latency jitter is compensated offline, the difference between accuracies is not significant. Significance. The lower temporal stability of the P300 evoked potential generated during the tasks performed in covert attention modality should be regarded as the main contributing explanation of lower accuracy of covert-attention ERP-based BCIs.

An examination of anticipated g-jitter on Space Station and its effects on materials processes

NASA Technical Reports Server (NTRS)

Nelson, Emily

1992-01-01

Information on anticipated g-jitter on Space Station Freedom and the effect of the jitter on materials processes is given in viewgraph form. It was concluded that g-jitter will dominate the acceleration environment; that it is a 3D multifrequency phenomenon; and that it varies dramatically in orientation. Information is given on calculated or measured sources of residual acceleration, aerodynamic drag, Shuttle acceleration measurements, the Space Station environment, tolerable g-levels as a function of frequency, directional solidification, vapor crystal growth, protein crystal growth, float zones, and liquid bridges.

Sub-100 attosecond timing jitter from low-noise passively mode-locked solid-state laser at telecom wavelength.

PubMed

Portuondo-Campa, E; Paschotta, R; Lecomte, S

2013-08-01

We report on the ultralow timing jitter of the 100 MHz pulse trains generated by two identical passively mode-locked diode-pumped solid-state lasers (DPSSLs) emitting at 1556 nm. Ultralow timing jitter of 83 as (integrated from 10 kHz to 50 MHz) for one laser has been measured with a balanced optical cross-correlator as timing discriminator. Extremely low intensity noise has been measured as well. Several measurement techniques have been used and show similar jitter results. Different possible noise sources have been theoretically investigated and compared to the measured jitter power spectral density. It is found that although the measured integrated jitter is quite low, it is still significantly above the quantum limit in the considered frequency span. Therefore, there is a substantial potential for technical improvements that could make passively mode-locked DPSSL outperform fiber lasers as source of microwaves with low phase noise.

Fall Detection System for the Elderly Based on the Classification of Shimmer Sensor Prototype Data

PubMed Central

Ahmed, Moiz; Mehmood, Nadeem; Mehmood, Amir; Rizwan, Kashif

2017-01-01

Objectives Falling in the elderly is considered a major cause of death. In recent years, ambient and wireless sensor platforms have been extensively used in developed countries for the detection of falls in the elderly. However, we believe extra efforts are required to address this issue in developing countries, such as Pakistan, where most deaths due to falls are not even reported. Considering this, in this paper, we propose a fall detection system prototype that s based on the classification on real time shimmer sensor data. Methods We first developed a data set, ‘SMotion’ of certain postures that could lead to falls in the elderly by using a body area network of Shimmer sensors and categorized the items in this data set into age and weight groups. We developed a feature selection and classification system using three classifiers, namely, support vector machine (SVM), K-nearest neighbor (KNN), and neural network (NN). Finally, a prototype was fabricated to generate alerts to caregivers, health experts, or emergency services in case of fall. Results To evaluate the proposed system, SVM, KNN, and NN were used. The results of this study identified KNN as the most accurate classifier with maximum accuracy of 96% for age groups and 93% for weight groups. Conclusions In this paper, a classification-based fall detection system is proposed. For this purpose, the SMotion data set was developed and categorized into two groups (age and weight groups). The proposed fall detection system for the elderly is implemented through a body area sensor network using third-generation sensors. The evaluation results demonstrate the reasonable performance of the proposed fall detection prototype system in the tested scenarios. PMID:28875049

Integrated Modeling Activities for the James Webb Space Telescope: Optical Jitter Analysis

NASA Technical Reports Server (NTRS)

Hyde, T. Tupper; Ha, Kong Q.; Johnston, John D.; Howard, Joseph M.; Mosier, Gary E.

2004-01-01

This is a continuation of a series of papers on the integrated modeling activities for the James Webb Space Telescope(JWST). Starting with the linear optical model discussed in part one, and using the optical sensitivities developed in part two, we now assess the optical image motion and wavefront errors from the structural dynamics. This is often referred to as "jitter: analysis. The optical model is combined with the structural model and the control models to create a linear structural/optical/control model. The largest jitter is due to spacecraft reaction wheel assembly disturbances which are harmonic in nature and will excite spacecraft and telescope structural. The structural/optic response causes image quality degradation due to image motion (centroid error) as well as dynamic wavefront error. Jitter analysis results are used to predict imaging performance, improve the structural design, and evaluate the operational impact of the disturbance sources.

Micro-jitter attenuation of spaceborne cooler by using a blade-type hyperelastic shape memory alloy passive isolator

NASA Astrophysics Data System (ADS)

Kwon, Seong-Cheol; Jeon, Young-Hyeon; Oh, Hyun-Ung

2017-10-01

In this study, the primary design objective is to develop a passive isolator that can guarantee structural safety of the cooler assembly in a launch vibration environment without a launch locking mechanism, while effectively isolating the cooler-induced micro-jitter during the on-orbit operation of the cooler. To achieve the design objective, we focused on the utilization of characteristics of the hyperelastic shape memory effects. The major advantage of the isolator is that the micro-jitter isolation performance is much less sensitive to the aligned position of the isolator in comparison with the conventional isolator. Moreover, implementation of an additional 0g compensation device during a satellite level on-ground test, such as a jitter measurement test, is not required. In this study, the basic characteristics of the isolator were measured using the torque test and free vibration test. The micro-jitter attenuation capability and position sensitivity of the proposed isolator design were validated by the micro-jitter measurement test.

Objective and Subjective Aspects of Voice in Pregnancy.

PubMed

Saltürk, Ziya; Kumral, Tolgar Lütfi; Bekiten, Güler; Atar, Yavuz; Ataç, Enes; Aydoğdu, İmran; Yıldırım, Güven; Kılıç, Aydın; Uyar, Yavuz

2016-01-01

This study aimed to evaluate vocal changes in pregnancy according to trimesters both objectively and subjectively. Fifty pregnant women and 15 nonpregnant women were included in the study. Eighteen of the 50 pregnant women were in the first trimester, 17 in the second trimester, and 15 in the third trimester of their pregnancies. The fundamental frequency (F0), jitter, shimmer, noise-to-harmonics ratio (NHR), and minimum and maximum pitch were determined during acoustic voice analysis. Laryngologic examination was evaluated via reflux finding score (RFS). Voice Handicap Index 10 (VHI-10) was used for subjective analysis. Maximum phonation time (MPT), VHI-10, and RFS were the parameters that differed significantly. MPT was significantly shorter in the third trimester. Acoustic analysis revealed that F0, jitter, shimmer, NHR, and minimum and maximum pitch values were not significantly different in any groups. RFS was higher in the first and third trimesters than the second trimester and control groups. VHI-10 scores were significantly higher in the third trimester. Our results showed that MPT is decreased during the third trimester, although acoustic parameters did not differ. VHI-10 results deteriorated in the third trimester significantly. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Short-period terrestrial planets and radial velocity stellar jitter.

NASA Astrophysics Data System (ADS)

Dumusque, Xavier

2015-01-01

Stellar jitter is the main limitation to ultra-precise radial velocity (RV) measurements. It currently precludes our ability to detect a planet like the Earth. Short-period terrestrial planets present first the advantage of inducing a stronger RV signal. In addition, the signal produced by these planets have a period completely different than stellar activity. This allows us, when the observational strategy is adequate, to decorrelate the planetary signal from the jitter induced by the star using filtering techniques. I will show the examples of Kepler-78b and Corot-7b, where the amplitude of the planetary signal can be detected, despite the stellar activity jitter that is 5 and 3 times larger, respectively. The cases of Alpha Cen Bb will also be reviewed, with a new reduction of the published data that increases the significance of the planetary signal.This project is funded by ETAEARTH, a transnational collaboration between European countries and the US (the Swiss Space Office, the Harvard Origin of Life Initiative, the Scottish Universities Physics Alliance, the University of Geneva, the Smithsonian Astrophysical Observatory, the Italian National Astrophysical Institute, the University of St. Andrews, Queens University Belfast, and the University of Edinburgh) setup to optimize the synergy between space-and ground-based data whose scientific potential for the characterization of extrasolar planets can only be fully exploited when analyzed together.

PLL jitter reduction by utilizing a ferroelectric capacitor as a VCO timing element.

PubMed

Pauls, Greg; Kalkur, Thottam S

2007-06-01

Ferroelectric capacitors have steadily been integrated into semiconductor processes due to their potential as storage elements within memory devices. Polarization reversal within ferroelectric capacitors creates a high nonlinear dielectric constant along with a hysteresis profile. Due to these attributes, a phase-locked loop (PLL), when based on a ferroelectric capacitor, has the advantage of reduced cycle-to-cycle jitter. PLLs based on ferroelectric capacitors represent a new research area for reduction of oscillator jitter.

Modelling the RV jitter of early-M dwarfs using tomographic imaging

NASA Astrophysics Data System (ADS)

Hébrard, É. M.; Donati, J.-F.; Delfosse, X.; Morin, J.; Moutou, C.; Boisse, I.

2016-09-01

In this paper, we show how tomographic imaging (Zeeman-Doppler imaging, ZDI) can be used to characterize stellar activity and magnetic field topologies, ultimately allowing us to filter out the radial velocity (RV) activity jitter of M dwarf moderate rotators. This work is based on spectropolarimetric observations of a sample of five weakly active early-M dwarfs (GJ 205, GJ 358, GJ 410, GJ 479, GJ 846) with HARPS-Pol and NARVAL. These stars have v sin I and RV jitters in the range 1-2 km s-1 and 2.7-10.0 m s-1 rms, respectively. Using a modified version of ZDI applied to sets of phase-resolved least-squares deconvolved profiles of unpolarized spectral lines, we are able to characterize the distribution of active regions at the stellar surfaces. We find that dark spots cover less than 2 per cent of the total surface of the stars of our sample. Our technique is efficient at modelling the rotationally modulated component of the activity jitter, and succeeds at decreasing the amplitude of this component by typical factors of 2-3 and up to 6 in optimal cases. From the rotationally modulated time series of circularly polarized spectra and with ZDI, we also reconstruct the large-scale magnetic field topology. These fields suggest that bistability of dynamo processes observed in active M dwarfs may also be at work for moderately active M dwarfs. Comparing spot distributions with field topologies suggest that dark spots causing activity jitter concentrate at the magnetic pole and/or equator, to be confirmed with future data on a larger sample.

A voltage-division-type low-jitter self-triggered repetition-rate switch.

PubMed

Su, Jian-Cang; Zeng, Bo; Gao, Peng-Cheng; Li, Rui; Wu, Xiao-Long; Zhao, Liang

2016-10-01

A voltage-division-type (V/N) low-jitter self-triggered multi-stage switch is put forward. It comprises of a triggered corona gap, several quasi-uniform-field gaps, and an inversion inductor. When the corona gap is in the stage of self-breakdown, the multi-stage gaps are triggered and the switch is closed via an over-voltage. This type of V/N switch has the advantage of compact structure since the auxiliary components like the gas-blowing system and the triggered system are eliminated from the whole system. It also has advantages such as low breakdown jitter and high energy efficiency. The dependence of the self-triggered voltage on the over-voltage factor and the switch operating voltage is deduced. A switch of this type is designed and fabricated and experiments to research its characteristics are conducted. The results show that this switch can operate on a voltage of 1 MV at 50 Hz and can generate 1000 successive pulses with a jitter as low as 3% and an energy efficiency as high as 90%. This V/N switch can work under a high repetition rate with a long lifetime.

Ultralow-jitter and -amplitude-noise semiconductor-based actively mode-locked laser.

PubMed

Quinlan, Franklyn; Gee, Sangyoun; Ozharar, Sarper; Delfyett, Peter J

2006-10-01

We report a semiconductor-based, low-noise, 10.24 GHz actively mode-locked laser with 4.65 fs of relative timing jitter and a 0.0365% amplitude fluctuation (1 Hz to 100 MHz) of the optical pulse train. The keys to obtaining this result were the laser's high optical power and the low phase noise of the rf source used to mode lock the laser. The low phase noise of the rf source not only improves the absolute and relative timing jitter of the laser, but also prevents coupling of the rf source phase noise to the pulse amplitude fluctuations by the mode-locked laser.

Influence of group-delay ripple on timing jitter induced by SPM and IXPM in systems with dispersion compensated by CFBG

NASA Astrophysics Data System (ADS)

Qin, Xi; Cao, Jihong; Chen, Yong; Zhang, Feng; Jian, Shuisheng

2007-08-01

An analytical expression was proposed to analyze the influence of group-delay ripple (GDR) on timing jitter induced by self-phase modulation (SPM) and intra-channel cross-phase modulation (IXPM) in pseudo-linear transmission systems when dispersion was compensated by chirped fiber Bragg grating (CFBG). Effects of ripple amplitude, period, and phase on timing jitter were discussed by theoretical and numerical analysis in detail. The results show that the influence of GDR on timing jitter changes linearly with the amplitude of GDR and whether it decreases or increases the timing jitter relies on the ripple period and ripple phase. Timing jitter induced by SPM and IXPM could be suppressed totally by adjusting the relative phase between the center frequency of the pulse and the ripples.

Change of signs, symptoms and voice quality evaluations throughout a 3- to 6-month empirical treatment for laryngopharyngeal reflux disease.

PubMed

Lechien, J R; Finck, C; Khalife, M; Huet, K; Delvaux, V; Picalugga, M; Harmegnies, B; Saussez, S

2018-05-16

To assess the usefulness of voice quality measurements as a treatment outcome in patients with laryngopharyngeal reflux (LPR)-related symptoms. Prospective uncontrolled multi-centre study. A total of 80 clinically diagnosed LPR patients with a reflux finding score (RFS)>7 and a reflux symptom index (RSI)>13 were treated with pantoprazole and diet recommendations during 3 or 6 months, according to their evolution. RSI; RFS; blinded Grade, Roughness, Breathiness, Asthenia, Strain and Instability (GRBASI) and aerodynamic and acoustic measurements were evaluated at baseline, 3 months (n = 80), and 6 months (n = 41) post-treatment. We conducted a correlation analysis between the adherence to the diet, and the evolution of both signs and symptoms and between videolaryngostroboscopic signs and acoustic measurements. Reflux symptom index, RFS, perceptual voice quality evaluations (dysphonia, roughness, strain and instability), and aerodynamic and acoustic measurements (ie, percent jitter and percent shimmer) were significantly improved at 3 months post-treatment but not at 6 months. Percent jitter was the most useful outcome for evaluating the clinical evolution of patients throughout the treatment course. A significant relationship between globus sensation and posterior commissure hypertrophy was documented; both seemed to significantly improve from 3 to 6 months. The correlation analysis revealed correlations between adherence to diet recommendations and the improvement of symptoms and between posterior commissure granulation severity and acoustic measurement impairments. Voice quality improved in a manner similar to both signs and symptoms throughout a 6-month empirical treatment with better improvement the 3 first months. Voice quality assessments can be used as indicators of treatment effectiveness in patients with LPR-related symptoms. © 2018 John Wiley & Sons Ltd.

A novel low-jitter plasma-jet triggered gas switch operated at a low working coefficient.

PubMed

Tie, Weihao; Liu, Shanhong; Liu, Xuandong; Zhang, Qiaogen; Pang, Lei; Liu, Longchen

2014-02-01

In this paper, we described the fabrication and testing of a novel plasma-jet triggered gas switch (PJTGS) operated at extremely low working coefficients with excellent triggered jitters. While the structure of the PJTGS is similar to that of a traditional three-electrode field-distortion gas switch, to improve its triggered performance we used a conical micro-plasma-gun with a needle-to-plate spark gap embedded in the trigger electrode. Applying a nanosecond pulse to the trigger electrode caused a spark discharge in the micro-plasma-gun. The electric field drove the discharge plasma to spray into the spark gap of the gas switch, causing fast breakdown. We tested the PJTGS with charging voltages of ±25 kV and a trigger voltage of +80 kV (5 ns rise time and 80 ns full width at half maximum) in two working modes. The PJTGS operated in Mode II had a lower triggered jitter and could be operated over a wider range of working coefficients than in Mode I under the same conditions. At working coefficients higher than 70%, we obtained sub-ns triggered jitters (<0.89 ns) from the PJTGS, at working coefficients lower than 50%, we obtained triggered jitters of 1.6-3.5 ns without no-fires or pre-fires. Even at a working coefficient of 27.4%, the PJTGS could still be triggered reliably with a delay time of 96.1 ns and a triggered jitter of 3.5 ns, respectively.

A novel trigger for pseudospark switch with high repetition rate, low jitter, and compact structure

NASA Astrophysics Data System (ADS)

Yan, Jiaqi; Shen, Saikang; Wang, Yanan; Zhang, Siyu; Cheng, Le; Ding, Weidong

2018-06-01

This paper presents the design and development of a trigger with a high repetition rate, low jitter, and compact structure for the pseudospark switch (PSS), which includes an improved Marx generator based on avalanche transistors and a corona-plasma trigger unit. The generator adopted a novel 3 × 12-stage Marx circuit based on avalanche transistors in which the failure rate of transistors in the first and second stages was significantly reduced by connecting the parallel capacitors compared to the previous similar generator. The reason for the improved performance was also discussed. The main parameters of output pulses were an amplitude of -7 kV, rise time of 6 ns, jitter of 0.2 ns, and repetition rate of 2 kHz. The corona-plasma trigger unit adopted BaTiO3 ceramics with high ɛr as the dielectric and was arranged in the hollow cathode of the PSS. The experiments of triggering a PSS prototype were conducted. The influence of anode voltage and pressure on the trigger delay and jitter was studied, and the minimum trigger jitter achieved <1 ns. This trigger worked for 107 shots at the repetition rate of 2 kHz continuously without obvious performance degradation and any failure of the generator. The main advantage of this trigger is the simultaneous combination of the high repetition rate, low jitter, long lifetime, and great simplicity in a compact structure.

The development of high-voltage repetitive low-jitter corona stabilized triggered switch

NASA Astrophysics Data System (ADS)

Geng, Jiuyuan; Yang, Jianhua; Cheng, Xinbing; Yang, Xiao; Chen, Rong

2018-04-01

The high-power switch plays an important part in a pulse power system. With the trend of pulse power technology toward modularization, miniaturization, and accuracy control, higher requirements on electrical trigger and jitter of the switch have been put forward. A high-power low-jitter corona-stabilized triggered switch (CSTS) is designed in this paper. This kind of CSTS is based on corona stabilized mechanism, and it can be used as a main switch of an intense electron-beam accelerator (IEBA). Its main feature was the use of an annular trigger electrode instead of a traditional needle-like trigger electrode, taking main and side trigger rings to fix the discharging channels and using SF6/N2 gas mixture as its operation gas. In this paper, the strength of the local field enhancement was changed by a trigger electrode protrusion length Dp. The differences of self-breakdown voltage and its stability, delay time jitter, trigger requirements, and operation range of the switch were compared. Then the effect of different SF6/N2 mixture ratio on switch performance was explored. The experimental results show that when the SF6 is 15% with the pressure of 0.2 MPa, the hold-off voltage of the switch is 551 kV, the operating range is 46.4%-93.5% of the self-breakdown voltage, the jitter is 0.57 ns, and the minimum trigger voltage requirement is 55.8% of the peak. At present, the CSTS has been successfully applied to an IEBA for long time operation.

The development of high-voltage repetitive low-jitter corona stabilized triggered switch.

PubMed

Geng, Jiuyuan; Yang, Jianhua; Cheng, Xinbing; Yang, Xiao; Chen, Rong

2018-04-01

The high-power switch plays an important part in a pulse power system. With the trend of pulse power technology toward modularization, miniaturization, and accuracy control, higher requirements on electrical trigger and jitter of the switch have been put forward. A high-power low-jitter corona-stabilized triggered switch (CSTS) is designed in this paper. This kind of CSTS is based on corona stabilized mechanism, and it can be used as a main switch of an intense electron-beam accelerator (IEBA). Its main feature was the use of an annular trigger electrode instead of a traditional needle-like trigger electrode, taking main and side trigger rings to fix the discharging channels and using SF 6 /N 2 gas mixture as its operation gas. In this paper, the strength of the local field enhancement was changed by a trigger electrode protrusion length Dp. The differences of self-breakdown voltage and its stability, delay time jitter, trigger requirements, and operation range of the switch were compared. Then the effect of different SF 6 /N 2 mixture ratio on switch performance was explored. The experimental results show that when the SF 6 is 15% with the pressure of 0.2 MPa, the hold-off voltage of the switch is 551 kV, the operating range is 46.4%-93.5% of the self-breakdown voltage, the jitter is 0.57 ns, and the minimum trigger voltage requirement is 55.8% of the peak. At present, the CSTS has been successfully applied to an IEBA for long time operation.

Multi-megavolt low jitter multistage switch

DOEpatents

Humphreys, D.R.; Penn, K.J. Jr.

1985-06-19

It is one object of the present invention to provide a multistage switch capable of holding off numerous megavolts, until triggered, from a particle beam accelerator of the type used for inertial confinement fusion. The invention provides a multistage switch having low timing jitter and capable of producing multiple spark channels for spreading current over a wider area to reduce electrode damage and increase switch lifetime. The switch has fairly uniform electric fields and a short spark gap for laser triggering and is engineered to prevent insulator breakdowns.

Time-jittered marine seismic data acquisition via compressed sensing and sparsity-promoting wavefield reconstruction

NASA Astrophysics Data System (ADS)

Wason, H.; Herrmann, F. J.; Kumar, R.

2016-12-01

Current efforts towards dense shot (or receiver) sampling and full azimuthal coverage to produce high resolution images have led to the deployment of multiple source vessels (or streamers) across marine survey areas. Densely sampled marine seismic data acquisition, however, is expensive, and hence necessitates the adoption of sampling schemes that save acquisition costs and time. Compressed sensing is a sampling paradigm that aims to reconstruct a signal--that is sparse or compressible in some transform domain--from relatively fewer measurements than required by the Nyquist sampling criteria. Leveraging ideas from the field of compressed sensing, we show how marine seismic acquisition can be setup as a compressed sensing problem. A step ahead from multi-source seismic acquisition is simultaneous source acquisition--an emerging technology that is stimulating both geophysical research and commercial efforts--where multiple source arrays/vessels fire shots simultaneously resulting in better coverage in marine surveys. Following the design principles of compressed sensing, we propose a pragmatic simultaneous time-jittered time-compressed marine acquisition scheme where single or multiple source vessels sail across an ocean-bottom array firing airguns at jittered times and source locations, resulting in better spatial sampling and speedup acquisition. Our acquisition is low cost since our measurements are subsampled. Simultaneous source acquisition generates data with overlapping shot records, which need to be separated for further processing. We can significantly impact the reconstruction quality of conventional seismic data from jittered data and demonstrate successful recovery by sparsity promotion. In contrast to random (sub)sampling, acquisition via jittered (sub)sampling helps in controlling the maximum gap size, which is a practical requirement of wavefield reconstruction with localized sparsifying transforms. We illustrate our results with simulations of

NASA Instep/mdmsc Jitter Suppression Experiment (JITTER)

NASA Technical Reports Server (NTRS)

White, Edward V.

1992-01-01

The objectives are the following: (1) to develop and demonstrate in-space performance of both passive and active damping systems for suppression of micro-amplitude vibration on an actual application structure and operate despite uncertain dynamics and uncertain disturbance characteristics; and (2) to correlate ground and in-space performance - the performance metric is vibration attenuation. The goals are to achieve vibration suppression equivalent to 5 percent passive damping in selected models and 15 percent active damping in selected modes. Various aspects of this experiment are presented in viewgraph form.

Efficient modeling of phase jitter in dispersion-managed soliton systems.

PubMed

McKinstrie, C J; Xie, C; Lakoba, T I

2002-11-01

The variational method is used to derive correlation equations that model phase jitter in dispersion-managed soliton systems. The predictions of these correlation equations are consistent with numerical solutions of the nonlinear Schrödinger equation on which they are based.

Low jitter, low inductance solid dielectric switches.

PubMed

Guenther, A H; Strickland, D M; Bettis, J R

1979-11-01

It has been shown that the use of graded solid dielectric sandwiches in laser-triggered spark gaps (LTS) can lead to highly desirable multichannel operations while maintaining the low delay and jitter performance characteristics of LTS. As many as ten separate breakdown channels were observed when small circular or hexagonal aluminum inserts were inserted between two Mylar dielectric sheets stressed at 4.1 kV/mil. A reduction in rise time was noted for these multichannel switching events.

Vocal Performance of Group Fitness Instructors Before and After Instruction: Changes in Acoustic Measures and Self-Ratings.

PubMed

Dallaston, Katherine; Rumbach, Anna F

2016-01-01

(1) To quantify acute changes in acoustic parameters of the voices of group fitness instructors (GFIs) before and after exercise instruction. (2) To determine whether these changes are discernible perceptually by the instructor. This is a pilot prospective cohort study. Participants were six female GFIs, based in Brisbane, Australia. Participants performed a series of vocal tasks before and after instruction of a 60-minute exercise class. Data were obtained pertaining to fundamental frequency (pitch), intensity (volume), jitter, shimmer, harmonic-to-noise ratio (HNR), maximum duration of sustained phonation (MDSP), and pitch range. Additionally, self-ratings of voice quality were obtained before and after instruction. Data were analyzed using the Wilcoxon signed rank test. Significant increases (P ≤ 0.05) were found in fundamental frequency and intensity after instruction. No significant changes in jitter, shimmer, HNR, or MDSP were found before and after instruction. For the group, no significant change in self-ratings of voice quality occurred before and after instruction. Statistically significant changes in pitch and volume were found on acoustic analysis. However, these subtle changes remained within the limits of what is considered normal and representative of the participant's age and gender. Further research into the effects of exercise instruction on the voice is needed. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Avalanche buildup and propagation effects on photon-timing jitter in Si-SPAD with non-uniform electric field

NASA Astrophysics Data System (ADS)

Ingargiola, Antonino; Assanelli, Mattia; Gallivanoni, Andrea; Rech, Ivan; Ghioni, Massimo; Cova, Sergio

2009-05-01

Improving SPAD performances, such as dark count rate and quantum efficiency, without degrading the photontiming jitter is a challenging task that requires a clear understanding of the physical mechanisms involved. In this paper we investigate the contribution of the avalanche buildup statistics and the lateral avalanche propagation to the photon-timing jitter in silicon SPAD devices. Recent works on the buildup statistics focused on the uniform electric field case, however these results can not be applied to Si SPAD devices in which field profile is far from constant. We developed a 1-D Monte Carlo (MC) simulator using the real non-uniform field profiles derived from Secondary Ion Mass Spectroscopy (SIMS) measurements. Local and non-local models for impact ionization phenomena were considered. The obtained results, in particular the mean multiplication rate and jitter of the buildup filament, allowed us to simulate the statistical spread of the avalanche current on the device active area. We included space charge effects and a detailed lumped model for the external electronics and parasitics. We found that, in agreement with some experimental evidences, the avalanche buildup contribution to the total timing jitter is non-negligible in our devices. Moreover the lateral propagation gives an additional contribution that can explain the increasing trend of the photon-timing jitter with the comparator threshold.

Requirements Formulation and Dynamic Jitter Analysis for Fourier-Kelvin Stellar Interferometer

NASA Technical Reports Server (NTRS)

Liu, Kuo-Chia; Hyde, Tristram; Blaurock, Carl; Bolognese, Jeff; Howard, Joseph; Danchi, William

2004-01-01

The Fourier-Kelvin Stellar Interferometer (FKSI) has been proposed to detect and characterize extra solar giant planets. The baseline configuration for FKSI is a two- aperture, structurally connected nulling interferometer, capable of providing null depth less than lo4 in the infrared. The objective of this paper is to summarize the process for setting the top level requirements and the jitter analysis performed on FKSI to date. The first part of the paper discusses the derivation of dynamic stability requirements, necessary for meeting the FKSI nulling demands. An integrated model including structures, optics, and control systems has been developed to support dynamic jitter analysis and requirements verification. The second part of the paper describes how the integrated model is used to investigate the effects of reaction wheel disturbances on pointing and optical path difference stabilities.

Phase jitter in a differential phase experiment.

NASA Technical Reports Server (NTRS)

Tanenbaum, B. S.; Connolly, D. J.; Austin, G. L.

1973-01-01

Austin (1971) had concluded that, because of the 'phase jitter,' the differential phase experiment is useful over a more limited height range than the differential absorption experiment. Several observations are presented to show that this conclusion is premature. It is pointed out that the logical basis of the differential absorption experiment also requires that the O- and X-mode echoes, at a given time, come from the same irregularities. Austin's calculations are believed to contain a systematic error above 80 km.

Sloshing dynamics modulated fluid angular momentum and moment fluctuations driven by orbital gravity gradient and jitter accelerations in microgravity

NASA Technical Reports Server (NTRS)

Hung, R. J.; Pan, H. L.

1995-01-01

The dynamical behavior of spacecraft propellant affected by the asymmetric combined gravity gradient and jitter accelerations, in particular the effect of surface tension on partially-filled rotating fluids applicable to a full-scale Gravity Probe-B Spacecraft dewar tank has been investigated. Three different cases of orbital accelerations: (1) gravity gradient-dominated, (2) equally weighted between gravity gradient and jitter, and (3) gravity jitter-dominated accelerations are studied. The results of slosh wave excitation along the liquid-vapor interface induced by gravity gradient-dominated accelerations provide a torsional moment with tidal motion of bubble oscillations in the rotating dewar. The results are clearly seen from the twisting shape of the bubble oscillations driven by gravity gradient-dominated acceleration. The results of slosh wave excitation along the liquid-vapor interface induced by gravity jitter-dominated acceleration indicate the results of bubble motion in a manner of down-and-up and leftward-and-rightward movement of oscillation when the bubble is rotating with respect to rotating dewar axis. Fluctuations of angular momentum, fluid moment and bubble mass center caused by slosh wave excitations driven by gravity gradient acceleration or gravity jitter acceleration are also investigated.

Reduction of timing jitter in passively Q-switched microchip lasers using self-injection seeding.

PubMed

Steinmetz, Alexander; Nodop, Dirk; Martin, Andreas; Limpert, Jens; Tünnermann, Andreas

2010-09-01

We present an efficient, simple, and passive technique for the reduction of timing jitter in passively Q-switched microchip lasers via self-injection seeding using a fiber delay line. The presented approach mitigates one inherent issue of passively Q-switched lasers without the need for active stabilization. At a repetition rate of a few hundred kilohertz and pulse duration of approximately 200 ps delivered by a microchip laser, the rms jitter is reduced from several nanoseconds down to 20 ps, hence, significantly below the pulse duration of the laser source.

RF Jitter Modulation Alignment Sensing

NASA Astrophysics Data System (ADS)

Ortega, L. F.; Fulda, P.; Diaz-Ortiz, M.; Perez Sanchez, G.; Ciani, G.; Voss, D.; Mueller, G.; Tanner, D. B.

2017-01-01

We will present the numerical and experimental results of a new alignment sensing scheme which can reduce the complexity of alignment sensing systems currently used, while maintaining the same shot noise limited sensitivity. This scheme relies on the ability of electro-optic beam deflectors to create angular modulation sidebands in radio frequency, and needs only a single-element photodiode and IQ demodulation to generate error signals for tilt and translation degrees of freedom in one dimension. It distances itself from current techniques by eliminating the need for beam centering servo systems, quadrant photodetectors and Gouy phase telescopes. RF Jitter alignment sensing can be used to reduce the complexity in the alignment systems of many laser optical experiments, including LIGO and the ALPS experiment.

Reduction of timing jitter and intensity noise in normal-dispersion passively mode-locked fiber lasers by narrow band-pass filtering.

PubMed

Qin, Peng; Song, Youjian; Kim, Hyoji; Shin, Junho; Kwon, Dohyeon; Hu, Minglie; Wang, Chingyue; Kim, Jungwon

2014-11-17

Fiber lasers mode-locked with normal cavity dispersion have recently attracted great attention due to large output pulse energy and femtosecond pulse duration. Here we accurately characterized the timing jitter of normal-dispersion fiber lasers using a balanced cross-correlation method. The timing jitter characterization experiments show that the timing jitter of normal-dispersion mode-locked fiber lasers can be significantly reduced by using narrow band-pass filtering (e.g., 7-nm bandwidth filtering in this work). We further identify that the timing jitter of the fiber laser is confined in a limited range, which is almost independent of cavity dispersion map due to the amplifier-similariton formation by insertion of the narrow bandpass filter. The lowest observed timing jitter reaches 0.57 fs (rms) integrated from 10 kHz to 10 MHz Fourier frequency. The rms relative intensity noise (RIN) is also reduced from 0.37% to 0.02% (integrated from 1 kHz to 5 MHz Fourier frequency) by the insertion of narrow band-pass filter.

Broadband noise limit in the photodetection of ultralow jitter optical pulses.

PubMed

Sun, Wenlu; Quinlan, Franklyn; Fortier, Tara M; Deschenes, Jean-Daniel; Fu, Yang; Diddams, Scott A; Campbell, Joe C

2014-11-14

Applications with optical atomic clocks and precision timing often require the transfer of optical frequency references to the electrical domain with extremely high fidelity. Here we examine the impact of photocarrier scattering and distributed absorption on the photocurrent noise of high-speed photodiodes when detecting ultralow jitter optical pulses. Despite its small contribution to the total photocurrent, this excess noise can determine the phase noise and timing jitter of microwave signals generated by detecting ultrashort optical pulses. A Monte Carlo simulation of the photodetection process is used to quantitatively estimate the excess noise. Simulated phase noise on the 10 GHz harmonic of a photodetected pulse train shows good agreement with previous experimental data, leading to the conclusion that the lowest phase noise photonically generated microwave signals are limited by photocarrier scattering well above the quantum limit of the optical pulse train.

Variable Delay Element For Jitter Control In High Speed Data Links

DOEpatents

Livolsi, Robert R.

2002-06-11

A circuit and method for decreasing the amount of jitter present at the receiver input of high speed data links which uses a driver circuit for input from a high speed data link which comprises a logic circuit having a first section (1) which provides data latches, a second section (2) which provides a circuit generates a pre-destorted output and for compensating for level dependent jitter having an OR function element and a NOR function element each of which is coupled to two inputs and to a variable delay element as an input which provides a bi-modal delay for pulse width pre-distortion, a third section (3) which provides a muxing circuit, and a forth section (4) for clock distribution in the driver circuit. A fifth section is used for logic testing the driver circuit.

LANDSAT-D MSS/TM tuned orbital jitter analysis model LDS900

NASA Technical Reports Server (NTRS)

Pollak, T. E.

1981-01-01

The final LANDSAT-D orbital dynamic math model (LSD900), comprised of all test validated substructures, was used to evaluate the jitter response of the MSS/TM experiments. A dynamic forced response analysis was performed at both the MSS and TM locations on all structural modes considered (thru 200 Hz). The analysis determined the roll angular response of the MSS/TM experiments to improve excitation generated by component operation. Cross axis and cross experiment responses were also calculated. The excitations were analytically represented by seven and nine term Fourier series approximations, for the MSS and TM experiment respectively, which enabled linear harmonic solution techniques to be applied to response calculations. Single worst case jitter was estimated by variations of the eigenvalue spectrum of model LSD 900. The probability of any worst case mode occurrence was investigated.

Acoustic and perceptual characteristics of the voice in patients with vocal polyps after surgery and voice therapy.

PubMed

Petrovic-Lazic, Mirjana; Jovanovic, Nadica; Kulic, Milan; Babac, Snezana; Jurisic, Vladimir

2015-03-01

The aim of the study was to assess the effect of endolaryngeal phonomicrosurgery (EPM) and voice therapy in patients with vocal fold polyps using perceptual and acoustic analysis before and after both therapies. The acoustic tests and perceptual evaluation of voice were carried out on 41 female patients with vocal fold polyp before and after EPM and voice therapy. Both therapy strategies were performed. Used acoustic parameters were Jitter percent (Jitt), pitch perturbation quotient (PPQ), shimmer percent (Shim), amplitude perturbation quotient (APQ), fundamental frequency variation (vF0), noise-to-harmonic ratio (NHR), Voice Turbulence Index (VTI). For perceptual evaluation, GRB scale was used. Results indicated higher values of investigated parameters in patients' group than in the control group (P < 0.01). Good correlation between the perceptual hoarseness factors of GRB scale and objective acoustic voice parameters were observed. All analyzed acoustic parameters improved after the phonomicrosurgery and voice therapy and tend to approach to values of the control group. For Jitt percent, Shim percent, vF0, VTI, and NHR, there were statistically significant differences. Perceptual voice evaluation revealed statistically significantly (P < 0.01) decreased rating of G (grade), R (rough) and B (breathy) after surgery and voice therapy. Our data indicated that both acoustic and perceptual characteristic of voice in patients with vocal polyps significantly improved after phonomicrosurgical and voice treatment. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Astrometric Jitter of the Sun as a Star

DTIC Science & Technology

2010-05-01

active, fast-rotating stars. The research described in this paper was carried out at the Jet Propulsion Laboratory, California Institute of Technology...as the Sun is not affected by star spot noise, but the prospects for more active stars may be limited to giant planets. Subject headings: open clusters ...nearby dwarfs should be as amenable to exoplanet detection as the Sun. The aim of this paper is to determine the solar astrometric jitter directly

Multifrequency zero-jitter delay-locked loop

NASA Astrophysics Data System (ADS)

Efendovich, Avner; Afek, Yachin; Sella, Coby; Bikowsky, Zeev

1994-01-01

The approach of an all-digital phase locked loop is used in this delay-locked loop circuit. This design is designated to a system with two processing units, a master CPU and a slave system chip, that share the same bus. It allows maximum utilization of the bus, as the minimal skew between the clocks of the two components significantly reduces idle periods, and also set-up and hold times. Changes in the operating frequency are possible, without falling out of synchronization. Due to the special lead-lag phase detector, the jitter of the clock is zero, when the loop is locked, under any working conditions.

Correlation of VHI-30 to Acoustic Measurements Across Three Common Voice Disorders.

PubMed

Dehqan, Ali; Yadegari, Fariba; Scherer, Ronald C; Dabirmoghadam, Peyman

2017-01-01

Voice disorders that affect the quality of voice also result in varying degrees of psychological and social problems. The research question here is whether the correlations between Voice Handicap Index (VHI)-30 scores and objective acoustic measures differ in patients with different types of voice disorders. The subjects were divided into three groups: muscle tension dysphonia (MTD), benign mid-membranous vocal fold lesions, and unilateral vocal fold paralysis (UVFP). All participants were male. The mean age for the groups were 32.85 ± 8.6 years in the MTD group, 33.24 ± 7.32 years in the benign lesions group, and 34.24 ± 7.51 years in the UVFP group. The participants completed the Persian VHI-30 questionnaire. PRAAT software was used to obtain acoustic analyses. There was a significant correlation between the physical subscale of the VHI-30 and the total score of the VHI-30 and maximum phonation time (MPT) in the MTD group. Also, there was a significant correlation between the total VHI-30 score and the MPT value. There were relatively strong and significant correlations between the physical subscale of the VHI-30 with jitter and shimmer, harmonics-to-noise ratio (HNR) for the group with benign lesions such as nodules and polyps. Also, in this group, there was a significant correlation between the total VHI-30 score and the jitter value. The physical scale had strong and significant correlations between jitter, shimmer, and HNR in the unilateral paralysis group. Findings suggest that although the VHI-30 and the acoustic measurements of voice provide independent information, they are associated to some extent. Copyright © 2017 The Voice Foundation. All rights reserved.

Intracavity dispersion effect on timing jitter of ultralow noise mode-locked semiconductor based external-cavity laser.

PubMed

Gee, S; Ozharar, S; Plant, J J; Juodawlkis, P W; Delfyett, P J

2009-02-01

We report the generation of optical pulse trains with 380 as of residual timing jitter (1 Hz-1 MHz) from a mode-locked external-cavity semiconductor laser, through a combination of optimizing the intracavity dispersion and utilizing a high-power, low-noise InGaAsP quantum-well slab-coupled optical waveguide amplifier gain medium. This is, to our knowledge, the lowest residual timing jitter reported to date from an actively mode-locked laser.

Effect of tape recording on perturbation measures.

PubMed

Jiang, J; Lin, E; Hanson, D G

1998-10-01

Tape recorders have been shown to affect measures of voice perturbation. Few studies, however, have been conducted to quantitatively justify the use or exclusion of certain types of recorders in voice perturbation studies. This study used sinusoidal and triangular waves and synthesized vowels to compare perturbation measures extracted from directly digitized signals with those recorded and played back through various tape recorders, including 3 models of digital audio tape recorders, 2 models of analog audio cassette tape recorders, and 2 models of video tape recorders. Signal contamination for frequency perturbation values was found to be consistently minimal with digital recorders (percent jitter = 0.01%-0.02%), mildly increased with video recorders (0.05%-0.10%), moderately increased with a high-quality analog audio cassette tape recorder (0.15%), and most prominent with a low-quality analog audio cassette tape recorder (0.24%). Recorder effect on amplitude perturbation measures was lowest in digital recorders (percent shimmer = 0.09%-0.20%), mildly to moderately increased in video recorders and a high-quality analog audio cassette tape recorder (0.25%-0.45%), and most prominent in a low-quality analog audio cassette tape recorder (0.98%). The effect of cassette tape material, length of spooled tape, and duration of analysis were also tested and are discussed.

Multi-parameter analysis of titanium vocal fold medializing implant in an excised larynx model

PubMed Central

Witt, Rachel E.; Hoffman, Matthew R.; Friedrich, Gerhard; Rieves, Adam L.; Schoepke, Benjamin J.; Jiang, Jack J.

2010-01-01

Objective Evaluate the efficacy of the titanium vocal fold medializing implant (TVFMI) for the treatment of unilateral vocal fold paralysis (UVFP) based on acoustic, aerodynamic, and mucosal wave measurements in an excised larynx setup. Methods Measurements were recorded on eight excised canine larynges with simulated UVFP before and after medialization with the TVFMI. Results Phonation threshold flow (PTF) and phonation threshold power (PTW) decreased significantly after medialization (p<0.001; p=0.008). Phonation threshold pressure (PTP) also decreased, but this difference was not significant (p=0.081). Percent jitter and percent shimmer decreased significantly after medialization (p=0.005; p=0.034). Signal to noise ratio (SNR) increased significantly (p=0.05). Differences in mucosal wave characteristics were discernable, but not significant. Phase difference between the normal and paralyzed vocal fold and amplitude of the paralyzed vocal fold decreased (p=0.15; p=0.78). Glottal gap decreased significantly (p=0.004). Conclusions The TVFMI was effective in achieving vocal fold medialization, improving vocal aerodynamic and acoustic characteristics of phonation significantly and mucosal wave characteristics discernibly. This study provides objective, quantitative support for the use of the TVFMI in improving vocal function in patients with unilateral vocal fold paralysis. PMID:20336924

Does CPAP treatment affect the voice?

PubMed

Saylam, Güleser; Şahin, Mustafa; Demiral, Dilek; Bayır, Ömer; Yüceege, Melike Bağnu; Çadallı Tatar, Emel; Korkmaz, Mehmet Hakan

2016-12-20

The aim of this study was to investigate alterations in voice parameters among patients using continuous positive airway pressure (CPAP) for the treatment of obstructive sleep apnea syndrome. Patients with an indication for CPAP treatment without any voice problems and with normal laryngeal findings were included and voice parameters were evaluated before and 1 and 6 months after CPAP. Videolaryngostroboscopic findings, a self-rated scale (Voice Handicap Index-10, VHI-10), perceptual voice quality assessment (GRBAS: grade, roughness, breathiness, asthenia, strain), and acoustic parameters were compared. Data from 70 subjects (48 men and 22 women) with a mean age of 44.2 ± 6.0 years were evaluated. When compared with the pre-CPAP treatment period, there was a significant increase in the VHI-10 score after 1 month of treatment and in VHI- 10 and total GRBAS scores, jitter percent (P = 0.01), shimmer percent, noise-to-harmonic ratio, and voice turbulence index after 6 months of treatment. Vague negative effects on voice parameters after the first month of CPAP treatment became more evident after 6 months. We demonstrated nonsevere alterations in the voice quality of patients under CPAP treatment. Given that CPAP is a long-term treatment it is important to keep these alterations in mind.

Effect of Magnetic Fields on g-jitter Induced Convection and Solute Striation During Space Processing of Single Crystals

NASA Technical Reports Server (NTRS)

deGroh, H. C.; Li, K.; Li, B. Q.

2002-01-01

A 2-D finite element model is presented for the melt growth of single crystals in a microgravity environment with a superimposed DC magnetic field. The model is developed based on the deforming finite element methodology and is capable of predicting the phenomena of the steady and transient convective flows, heat transfer, solute distribution, and solid-liquid interface morphology associated with the melt growth of single crystals in microgravity with and without an applied magnetic field. Numerical simulations were carried out for a wide range of parameters including idealized microgravity conditions, the synthesized g-jitter and the real g-jitter data taken by on-board accelerometers during space flights. The results reveal that the time varying g-jitter disturbances, although small in magnitude, cause an appreciable convective flow in the liquid pool, which in turn produces detrimental effects during the space processing of single crystal growth. An applied magnetic field of appropriate strength, superimposed on microgravity, can be very effective in suppressing the deleterious effects resulting from the g-jitter disturbances.

Effects of g-Jitter on Diffusion in Binary Liquids

NASA Technical Reports Server (NTRS)

Duval, Walter M. B.

1999-01-01

The microgravity environment offers the potential to measure the binary diffusion coefficients in liquids without the masking effects introduced by buoyancy-induced flows due to Earth s gravity. However, the background g-jitter (vibrations from the shuttle, onboard machinery, and crew) normally encountered in many shuttle experiments may alter the benefits of the microgravity environment and introduce vibrations that could offset its intrinsic advantages. An experiment during STS-85 (August 1997) used the Microgravity Vibration Isolation Mount (MIM) to isolate and introduce controlled vibrations to two miscible liquids inside a cavity to study the effects of g-jitter on liquid diffusion. Diffusion in a nonhomogeneous liquid system is caused by a nonequilibrium condition that results in the transport of mass (dispersion of the different kinds of liquid molecules) to approach equilibrium. The dynamic state of the system tends toward equilibrium such that the system becomes homogeneous. An everyday example is the mixing of cream and coffee (a nonhomogeneous system) via stirring. The cream diffuses into the coffee, thus forming a homogeneous system. At equilibrium the system is said to be mixed. However, during stirring, simple observations show complex flow field dynamics-stretching and folding of material interfaces, thinning of striation thickness, self-similar patterns, and so on. This example illustrates that, even though mixing occurs via mass diffusion, stirring to enhance transport plays a major role. Stirring can be induced either by mechanical means (spoon or plastic stirrer) or via buoyancy-induced forces caused by Earth s gravity. Accurate measurements of binary diffusion coefficients are often inhibited by buoyancy-induced flows. The microgravity environment minimizes the effect of buoyancy-induced flows and allows the true diffusion limit to be achieved. One goal of this experiment was to show that the microgravity environment suppresses buoyancy

Simulation of Combustion Systems with Realistic g-jitter

NASA Technical Reports Server (NTRS)

Mell, William E.; McGrattan, Kevin B.; Baum, Howard R.

2003-01-01

In this project a transient, fully three-dimensional computer simulation code was developed to simulate the effects of realistic g-jitter on a number of combustion systems. The simulation code is capable of simulating flame spread on a solid and nonpremixed or premixed gaseous combustion in nonturbulent flow with simple combustion models. Simple combustion models were used to preserve computational efficiency since this is meant to be an engineering code. Also, the use of sophisticated turbulence models was not pursued (a simple Smagorinsky type model can be implemented if deemed appropriate) because if flow velocities are large enough for turbulence to develop in a reduced gravity combustion scenario it is unlikely that g-jitter disturbances (in NASA's reduced gravity facilities) will play an important role in the flame dynamics. Acceleration disturbances of realistic orientation, magnitude, and time dependence can be easily included in the simulation. The simulation algorithm was based on techniques used in an existing large eddy simulation code which has successfully simulated fire dynamics in complex domains. A series of simulations with measured and predicted acceleration disturbances on the International Space Station (ISS) are presented. The results of this series of simulations suggested a passive isolation system and appropriate scheduling of crew activity would provide a sufficiently "quiet" acceleration environment for spherical diffusion flames.

Wide tracking range, auto ranging, low jitter phase lock loop for swept and fixed frequency systems

DOEpatents

Kerner, Thomas M.

2001-01-01

The present invention provides a wide tracking range phase locked loop (PLL) circuit that achieves minimal jitter in a recovered clock signal, regardless of the source of the jitter (i.e. whether it is in the source or the transmission media). The present invention PLL has automatic harmonic lockout detection circuitry via a novel lock and seek control logic in electrical communication with a programmable frequency discriminator and a code balance detector. (The frequency discriminator enables preset of a frequency window of upper and lower frequency limits to derive a programmable range within which signal acquisition is effected. The discriminator works in combination with the code balance detector circuit to minimize the sensitivity of the PLL circuit to random data in the data stream). In addition, the combination of a differential loop integrator with the lock and seek control logic obviates a code preamble and guarantees signal acquisition without harmonic lockup. An adaptive cable equalizer is desirably used in combination with the present invention PLL to recover encoded transmissions containing a clock and/or data. The equalizer automatically adapts to equalize short haul cable lengths of coaxial and twisted pair cables or wires and provides superior jitter performance itself. The combination of the equalizer with the present invention PLL is desirable in that such combination permits the use of short haul wires without significant jitter.

Influence of G-jitter on the characteristics of a non-premixed flame: Experimental approach

NASA Astrophysics Data System (ADS)

Joulain, Pierre; Cordeiro, Pierre; Rouvreau, Sébastien; Legros, Guillaume; Fuentes, Andres; Torero, José L.

2005-03-01

The combustion of a flat plate in a boundary layer under microgravity conditions, which was first described by Emmons, is studied using a gas burner. Magnitude of injection and blowing velocities are chosen to be characteristic of pyrolyzing velocity of solid fuels, and of ventilation systems in space stations. These velocities are about 0.1 m/s for oxidiser flow and 0.004m/s for fuel flow. In this configuration, flame layout results from a coupled interaction between oxidiser flow, fuel flow and thermal expansion. Influences of these parameters are studied experimentally by means of flame length and standoff distance measurements using CH* chemiluminescence's and visible emission of the flame. Flow was also studied with Particle Image Velocimetry (PIV). Inert flows, with and without injection, and reacting flow in a microgravity environment were considered to distinguish aerodynamic from thermal effect. Thermal expansion effects have been shown by means of the acceleration of oxidiser flow. Three-dimensional effects, which are strongly marked for high injection velocities were studied. Three-dimensional tools adaptability to parabolic flights particular conditions were of concern. Flame sensitivity to g-jitters was investigated according to g-jitters frequency and range involved by parabolic flights. It appears that flame location (standoff distance), flame characteristics (length, thickness, brightness) and the aerodynamic field of the low velocity reacting flow are very much affected by the fluctuation of the gravity level or g-jitter. The lower the g-jitter frequency is, the higher the perturbation. Consequently it is difficult to perform relevant experiments for a main flow velocity lower than 0.05m/s. DNS calculations confirm the present observations, but most of the results are presented elsewhere.

High performance thyratron driver with low jitter.

PubMed

Verma, Rishi; Lee, P; Springham, S V; Tan, T L; Rawat, R S

2007-08-01

We report the design and development of insulated gate bipolar junction transistor based high performance driver for operating thyratrons in grounded grid mode. With careful design, the driver meets the specification of trigger output pulse rise time less than 30 ns, jitter less than +/-1 ns, and time delay less than 160 ns. It produces a -600 V pulse of 500 ns duration (full width at half maximum) at repetition rate ranging from 1 Hz to 1.14 kHz. The developed module also facilitates heating and biasing units along with protection circuitry in one complete package.

GABAergic excitation of spider mechanoreceptors increases information capacity by increasing entropy rather than decreasing jitter.

PubMed

Pfeiffer, Keram; French, Andrew S

2009-09-02

Neurotransmitter chemicals excite or inhibit a range of sensory afferents and sensory pathways. These changes in firing rate or static sensitivity can also be associated with changes in dynamic sensitivity or membrane noise and thus action potential timing. We measured action potential firing produced by random mechanical stimulation of spider mechanoreceptor neurons during long-duration excitation by the GABAA agonist muscimol. Information capacity was estimated from signal-to-noise ratio by averaging responses to repeated identical stimulation sequences. Information capacity was also estimated from the coherence function between input and output signals. Entropy rate was estimated by a data compression algorithm and maximum entropy rate from the firing rate. Action potential timing variability, or jitter, was measured as normalized interspike interval distance. Muscimol increased firing rate, information capacity, and entropy rate, but jitter was unchanged. We compared these data with the effects of increasing firing rate by current injection. Our results indicate that the major increase in information capacity by neurotransmitter action arose from the increased entropy rate produced by increased firing rate, not from reduction in membrane noise and action potential jitter.

Low-sensitivity H ∞ filter design for linear delta operator systems with sampling time jitter

NASA Astrophysics Data System (ADS)

Guo, Xiang-Gui; Yang, Guang-Hong

2012-04-01

This article is concerned with the problem of designing H ∞ filters for a class of linear discrete-time systems with low-sensitivity to sampling time jitter via delta operator approach. Delta-domain model is used to avoid the inherent numerical ill-condition resulting from the use of the standard shift-domain model at high sampling rates. Based on projection lemma in combination with the descriptor system approach often used to solve problems related to delay, a novel bounded real lemma with three slack variables for delta operator systems is presented. A sensitivity approach based on this novel lemma is proposed to mitigate the effects of sampling time jitter on system performance. Then, the problem of designing a low-sensitivity filter can be reduced to a convex optimisation problem. An important consideration in the design of correlation filters is the optimal trade-off between the standard H ∞ criterion and the sensitivity of the transfer function with respect to sampling time jitter. Finally, a numerical example demonstrating the validity of the proposed design method is given.

Note: A new method for directly reducing the sampling jitter noise of the digital phasemeter

NASA Astrophysics Data System (ADS)

Liang, Yu-Rong

2018-03-01

The sampling jitter noise is one non-negligible noise source of the digital phasemeter used for space gravitational wave detection missions. This note provides a new method for directly reducing the sampling jitter noise of the digital phasemeter, by adding a dedicated signal of which the frequency, amplitude, and initial phase should be pre-set. In contrast to the phase correction using the pilot-tone in the work of Burnett, Gerberding et al., Liang et al., Ales et al., Gerberding et al., and Ware et al. [M.Sc. thesis, Luleå University of Technology, 2010; Classical Quantum Gravity 30, 235029 (2013); Rev. Sci. Instrum. 86, 016106 (2015); Rev. Sci. Instrum. 86, 084502 (2015); Rev. Sci. Instrum. 86, 074501 (2015); and Proceedings of the Earth Science Technology Conference (NASA, USA, 2006)], the new method is intrinsically additive noise suppression. The experiment results validate that the new method directly reduces the sampling jitter noise without data post-processing and provides the same phase measurement noise level (10-6 rad/Hz1/2 at 0.1 Hz) as the pilot-tone correction.

Applied Chaos Level Test for Validation of Signal Conditions Underlying Optimal Performance of Voice Classification Methods.

PubMed

Liu, Boquan; Polce, Evan; Sprott, Julien C; Jiang, Jack J

2018-05-17

The purpose of this study is to introduce a chaos level test to evaluate linear and nonlinear voice type classification method performances under varying signal chaos conditions without subjective impression. Voice signals were constructed with differing degrees of noise to model signal chaos. Within each noise power, 100 Monte Carlo experiments were applied to analyze the output of jitter, shimmer, correlation dimension, and spectrum convergence ratio. The computational output of the 4 classifiers was then plotted against signal chaos level to investigate the performance of these acoustic analysis methods under varying degrees of signal chaos. A diffusive behavior detection-based chaos level test was used to investigate the performances of different voice classification methods. Voice signals were constructed by varying the signal-to-noise ratio to establish differing signal chaos conditions. Chaos level increased sigmoidally with increasing noise power. Jitter and shimmer performed optimally when the chaos level was less than or equal to 0.01, whereas correlation dimension was capable of analyzing signals with chaos levels of less than or equal to 0.0179. Spectrum convergence ratio demonstrated proficiency in analyzing voice signals with all chaos levels investigated in this study. The results of this study corroborate the performance relationships observed in previous studies and, therefore, demonstrate the validity of the validation test method. The presented chaos level validation test could be broadly utilized to evaluate acoustic analysis methods and establish the most appropriate methodology for objective voice analysis in clinical practice.

Acoustic and phonatory characterization of the Fado voice.

PubMed

Mendes, Ana P; Rodrigues, Aira F; Guerreiro, David Michael

2013-09-01

Fado is a Portuguese musical genre, instrumentally accompanied by a Portuguese and an acoustic guitar. Fado singers' voice is perceptually characterized by a low pitch, hoarse, and strained voice. The present research study sketches the acoustic and phonatory profile of the Fado singers' voice. Fifteen Fado singers produced spoken and sung phonatory tasks. For the spoken voice measures, the maximum phonation time and s/z ratio of Fado singers were near the inefficient physiological threshold. Fundamental frequency was higher than that found in nonsingers and lower than that found in Western Classical singers. Jitter and shimmer mean values were higher compared with nonsingers. Harmonic-to-noise ratio (HNR) was similar to the mean values for nonsingers. For the sung voice, jitter was higher compared with Country, Musical Theater, Soul, Jazz, and Western Classical singers and lower than Pop singers. Shimmer mean values were lower than Country, Musical Theater, Pop, Soul, and Jazz singers and higher than Western Classical singers. HNR was similar for Western Classical singers. Maximum phonational frequency range of Fado singers indicated that male and female subjects had a lower range compared with Western Classical singers. Additionally, Fado singers produced vibrato, but singer's formant was rarely produced. These sung voice characteristics could be related with life habits, less/lack of singing training, or could be just a Fado voice characteristic. Copyright © 2013 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Linear Polarization, Circular Polarization, and Depolarization of Gamma-ray Bursts: A Simple Case of Jitter Radiation

NASA Astrophysics Data System (ADS)

Mao, Jirong; Wang, Jiancheng

2017-04-01

Linear and circular polarizations of gamma-ray bursts (GRBs) have been detected recently. We adopt a simplified model to investigate GRB polarization characteristics in this paper. A compressed two-dimensional turbulent slab containing stochastic magnetic fields is considered, and jitter radiation can produce the linear polarization under this special magnetic field topology. Turbulent Faraday rotation measure (RM) of this slab makes strong wavelength-dependent depolarization. The jitter photons can also scatter with those magnetic clumps inside the turbulent slab, and a nonzero variance of the Stokes parameter V can be generated. Furthermore, the linearly and circularly polarized photons in the optical and radio bands may suffer heavy absorptions from the slab. Thus we consider the polarized jitter radiation transfer processes. Finally, we compare our model results with the optical detections of GRB 091018, GRB 121024A, and GRB 131030A. We suggest simultaneous observations of GRB multi-wavelength polarization in the future.

The effect of jitter on the performance of space coherent optical communication system with Costas loop

NASA Astrophysics Data System (ADS)

Li, Xin; Hong, Yifeng; Wang, Jinfang; Liu, Yang; Sun, Xun; Li, Mi

2018-01-01

Numerous communication techniques and optical devices successfully applied in space optical communication system indicates a good portability of it. With this good portability, typical coherent demodulation technique of Costas loop can be easily adopted in space optical communication system. As one of the components of pointing error, the effect of jitter plays an important role in the communication quality of such system. Here, we obtain the probability density functions (PDF) of different jitter degrees and explain their essential effect on the bit error rate (BER) space optical communication system. Also, under the effect of jitter, we research the bit error rate of space coherent optical communication system using Costas loop with different system parameters of transmission power, divergence angle, receiving diameter, avalanche photodiode (APD) gain, and phase deviation caused by Costas loop. Through a numerical simulation of this kind of communication system, we demonstrate the relationship between the BER and these system parameters, and some corresponding methods of system optimization are presented to enhance the communication quality.

Linear Polarization, Circular Polarization, and Depolarization of Gamma-ray Bursts: A Simple Case of Jitter Radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mao, Jirong; Wang, Jiancheng, E-mail: jirongmao@mail.ynao.ac.cn

Linear and circular polarizations of gamma-ray bursts (GRBs) have been detected recently. We adopt a simplified model to investigate GRB polarization characteristics in this paper. A compressed two-dimensional turbulent slab containing stochastic magnetic fields is considered, and jitter radiation can produce the linear polarization under this special magnetic field topology. Turbulent Faraday rotation measure (RM) of this slab makes strong wavelength-dependent depolarization. The jitter photons can also scatter with those magnetic clumps inside the turbulent slab, and a nonzero variance of the Stokes parameter V can be generated. Furthermore, the linearly and circularly polarized photons in the optical and radiomore » bands may suffer heavy absorptions from the slab. Thus we consider the polarized jitter radiation transfer processes. Finally, we compare our model results with the optical detections of GRB 091018, GRB 121024A, and GRB 131030A. We suggest simultaneous observations of GRB multi-wavelength polarization in the future.« less

Reorientation of rotating fluid in microgravity environment with and without gravity jitters

NASA Technical Reports Server (NTRS)

Hung, R. J.; Lee, C. C.; Shyu, K. L.

1990-01-01

In a spacecraft design, the requirements of settled propellant are different for tank pressurization, engine restart, venting, or propellant transfer. The requirement to settle or to position liquid fuel over the outlet end of the spacecraft propellant tank prior main engine restart poses a microgravity fluid behavior problem. In this paper, the dynamical behavior of liquid propellant, fluid reorientation, and propellant resettling have been carried out through the execution of supercomputer CRAY X-MP to simulate the fluid management in a microgravity environment. Results show that the resettlement of fluid can be accomplished more efficiently for fluid in rotating tank than in nonrotating tank, and also better performance for gravity jitters imposed on fluid settlement than without gravity jitters based on the amount of time needed to carry out resettlement period of time between the initiation and termination of geysering.

Attitude determination for high-accuracy submicroradian jitter pointing on space-based platforms

NASA Astrophysics Data System (ADS)

Gupta, Avanindra A.; van Houten, Charles N.; Germann, Lawrence M.

1990-10-01

A description of the requirement definition process is given for a new wideband attitude determination subsystem (ADS) for image motion compensation (IMC) systems. The subsystem consists of either lateral accelerometers functioning in differential pairs or gas-bearing gyros for high-frequency sensors using CCD-based star trackers for low-frequency sensors. To minimize error the sensor signals are combined so that the mixing filter does not allow phase distortion. The two ADS models are introduced in an IMC simulation to predict measurement error, correction capability, and residual image jitter for a variety of system parameters. The IMC three-axis testbed is utilized to simulate an incoming beam in inertial space. Results demonstrate that both mechanical and electronic IMC meet the requirements of image stabilization for space-based observation at submicroradian-jitter levels. Currently available technology may be employed to implement IMC systems.

Superior bit error rate and jitter due to improved switching field distribution in exchange spring magnetic recording media

PubMed Central

Suess, D.; Fuger, M.; Abert, C.; Bruckner, F.; Vogler, C.

2016-01-01

We report two effects that lead to a significant reduction of the switching field distribution in exchange spring media. The first effect relies on a subtle mechanism of the interplay between exchange coupling between soft and hard layers and anisotropy that allows significant reduction of the switching field distribution in exchange spring media. This effect reduces the switching field distribution by about 30% compared to single-phase media. A second effect is that due to the improved thermal stability of exchange spring media over single-phase media, the jitter due to thermal fluctuation is significantly smaller for exchange spring media than for single-phase media. The influence of this overall improved switching field distribution on the transition jitter in granular recording and the bit error rate in bit-patterned magnetic recording is discussed. The transition jitter in granular recording for a distribution of Khard values of 3% in the hard layer, taking into account thermal fluctuations during recording, is estimated to be a = 0.78 nm, which is similar to the best reported calculated jitter in optimized heat-assisted recording media. PMID:27245287

On the effects of phase jitter on QPSK lock detection

NASA Technical Reports Server (NTRS)

Mileant, A.; Hinedi, S.

1993-01-01

The performance of a QPSK (quadrature phase-shift keying) lock detector is described, taking into account the degradation due to carrier phase jitter. Such an analysis is necessary for accurate performance prediction purposes in scenarios where both the loop SNR is low and the estimation period is short. The derived formulas are applicable to several QPSK loops and are verified using computer simulations.

Data Reduction of Jittered Infrared Images Using the ORAC Pipeline

NASA Astrophysics Data System (ADS)

Currie, Malcolm; Wright, Gillian; Bridger, Alan; Economou, Frossie

We relate our experiences using the ORAC data reduction pipeline for jittered images of stars and galaxies. The reduction recipes currently combine applications from several Starlink packages with intelligent Perl recipes to cater to UKIRT data. We describe the recipes and some of the algorithms used, and compare the quality of the resultant mosaics and photometry with the existing facilities.

Acquisition and Initial Analysis of H+- and H--Beam Centroid Jitter at LANSCE

NASA Astrophysics Data System (ADS)

Gilpatrick, J. D.; Bitteker, L.; Gulley, M. S.; Kerstiens, D.; Oothoudt, M.; Pillai, C.; Power, J.; Shelley, F.

2006-11-01

During the 2005 Los Alamos Neutron Science Center (LANSCE) beam runs, beam current and centroid-jitter data were observed, acquired, analyzed, and documented for both the LANSCE H+ and H- beams. These data were acquired using three beam position monitors (BPMs) from the 100-MeV Isotope Production Facility (IPF) beam line and three BPMs from the Switchyard transport line at the end of the LANSCE 800-MeV linac. The two types of data acquired, intermacropulse and intramacropulse, were analyzed for statistical and frequency characteristics as well as various other correlations including comparing their phase-space like characteristics in a coordinate system of transverse angle versus transverse position. This paper will briefly describe the measurements required to acquire these data, the initial analysis of these jitter data, and some interesting dilemmas these data presented.

A compact, low jitter, nanosecond rise time, high voltage pulse generator with variable amplitude.

PubMed

Mao, Jiubing; Wang, Xin; Tang, Dan; Lv, Huayi; Li, Chengxin; Shao, Yanhua; Qin, Lan

2012-07-01

In this paper, a compact, low jitter, nanosecond rise time, command triggered, high peak power, gas-switch pulse generator system is developed for high energy physics experiment. The main components of the system are a high voltage capacitor, the spark gap switch and R = 50 Ω load resistance built into a structure to obtain a fast high power pulse. The pulse drive unit, comprised of a vacuum planar triode and a stack of avalanche transistors, is command triggered by a single or multiple TTL (transistor-transistor logic) level pulses generated by a trigger pulse control unit implemented using the 555 timer circuit. The control unit also accepts user input TTL trigger signal. The vacuum planar triode in the pulse driving unit that close the first stage switches is applied to drive the spark gap reducing jitter. By adjusting the charge voltage of a high voltage capacitor charging power supply, the pulse amplitude varies from 5 kV to 10 kV, with a rise time of <3 ns and the maximum peak current up to 200 A (into 50 Ω). The jitter of the pulse generator system is less than 1 ns. The maximum pulse repetition rate is set at 10 Hz that limited only by the gas-switch and available capacitor recovery time.

An examination of anticipated g-jitter on Space Station and its effects on materials processes

NASA Technical Reports Server (NTRS)

Nelson, Emily S.

1994-01-01

This study is concerned with the effects of g-jitter, the residual acceleration aboard spacecraft, on selected classes of materials processes. In particular, the anticipated acceleration environment aboard Space Station Freedom (SSF) and its potential effects are analyzed, but the topic is covered with a sufficient level of generality as to apply to other processes and to other vehicles as well. Some of the key findings of this study include: The present acceleration specifications for SSF are inadequate to assure a quality level low-g environment. The local g vector orientation is an extremely sensitive parameter for certain key processes, but can not be controlled to within the desired tolerance. Therefore, less emphasis should be placed upon achieving a tight control of SSF attitude, but more emphasis should be focused on reducing the overall level of the g-jitter magnitude. Melt-based crystal growth may not be successfully processed in the relatively noisy environment of a large inhabited space structure. Growth from vapor or from solution appears more favorable. A smaller space structure and/or a free flyer can provide better alternatives in terms of g-jitter considerations. A high priority (including budgetary) should be given to coordinated efforts among researchers, SSF designers, and equipment contractors, to develop practical experiment-specific sensitivity requirements. Combined focused numerical simulations and experiments with well-resolved acceleration measurements should be vigorously pursued for developing reliable experiment-specific sensitivity data. Appendices provide an extensive cross-referenced bibliography, a discussion of the merits offered by g-jitter analysis techniques, as well as definitions of relevant nondimensional quantities and a brief description of available accelerometry hardware.

Note: Design and implementation of a home-built imaging system with low jitter for cold atom experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hachtel, A. J.; Gillette, M. C.; Clements, E. R.

A novel home-built system for imaging cold atom samples is presented using a readily available astronomy camera which has the requisite sensitivity but no timing-control. We integrate the camera with LabVIEW achieving fast, low-jitter imaging with a convenient user-defined interface. We show that our system takes precisely timed millisecond exposures and offers significant improvements in terms of system jitter and readout time over previously reported home-built systems. Our system rivals current commercial “black box” systems in performance and user-friendliness.

Stereoscopic motion analysis in densely packed clusters: 3D analysis of the shimmering behaviour in Giant honey bees.

PubMed

Kastberger, Gerald; Maurer, Michael; Weihmann, Frank; Ruether, Matthias; Hoetzl, Thomas; Kranner, Ilse; Bischof, Horst

2011-02-08

The detailed interpretation of mass phenomena such as human escape panic or swarm behaviour in birds, fish and insects requires detailed analysis of the 3D movements of individual participants. Here, we describe the adaptation of a 3D stereoscopic imaging method to measure the positional coordinates of individual agents in densely packed clusters. The method was applied to study behavioural aspects of shimmering in Giant honeybees, a collective defence behaviour that deters predatory wasps by visual cues, whereby individual bees flip their abdomen upwards in a split second, producing Mexican wave-like patterns. Stereoscopic imaging provided non-invasive, automated, simultaneous, in-situ 3D measurements of hundreds of bees on the nest surface regarding their thoracic position and orientation of the body length axis. Segmentation was the basis for the stereo matching, which defined correspondences of individual bees in pairs of stereo images. Stereo-matched "agent bees" were re-identified in subsequent frames by the tracking procedure and triangulated into real-world coordinates. These algorithms were required to calculate the three spatial motion components (dx: horizontal, dy: vertical and dz: towards and from the comb) of individual bees over time. The method enables the assessment of the 3D positions of individual Giant honeybees, which is not possible with single-view cameras. The method can be applied to distinguish at the individual bee level active movements of the thoraces produced by abdominal flipping from passive motions generated by the moving bee curtain. The data provide evidence that the z-deflections of thoraces are potential cues for colony-intrinsic communication. The method helps to understand the phenomenon of collective decision-making through mechanoceptive synchronization and to associate shimmering with the principles of wave propagation. With further, minor modifications, the method could be used to study aspects of other mass phenomena that

Stereoscopic motion analysis in densely packed clusters: 3D analysis of the shimmering behaviour in Giant honey bees

PubMed Central

2011-01-01

Background The detailed interpretation of mass phenomena such as human escape panic or swarm behaviour in birds, fish and insects requires detailed analysis of the 3D movements of individual participants. Here, we describe the adaptation of a 3D stereoscopic imaging method to measure the positional coordinates of individual agents in densely packed clusters. The method was applied to study behavioural aspects of shimmering in Giant honeybees, a collective defence behaviour that deters predatory wasps by visual cues, whereby individual bees flip their abdomen upwards in a split second, producing Mexican wave-like patterns. Results Stereoscopic imaging provided non-invasive, automated, simultaneous, in-situ 3D measurements of hundreds of bees on the nest surface regarding their thoracic position and orientation of the body length axis. Segmentation was the basis for the stereo matching, which defined correspondences of individual bees in pairs of stereo images. Stereo-matched "agent bees" were re-identified in subsequent frames by the tracking procedure and triangulated into real-world coordinates. These algorithms were required to calculate the three spatial motion components (dx: horizontal, dy: vertical and dz: towards and from the comb) of individual bees over time. Conclusions The method enables the assessment of the 3D positions of individual Giant honeybees, which is not possible with single-view cameras. The method can be applied to distinguish at the individual bee level active movements of the thoraces produced by abdominal flipping from passive motions generated by the moving bee curtain. The data provide evidence that the z-deflections of thoraces are potential cues for colony-intrinsic communication. The method helps to understand the phenomenon of collective decision-making through mechanoceptive synchronization and to associate shimmering with the principles of wave propagation. With further, minor modifications, the method could be used to study

A 250 MHz, high power mode-locked Nd:GdVO4 oscillator with low timing jitter under 879 nm direct pumping

NASA Astrophysics Data System (ADS)

Zhang, F. F.; Zuo, J. W.; Wang, Z. M.; Yang, J.; Cheng, H. L.; Zong, N.; Yang, F.; Peng, Q. J.; Xu, Z. Y.

2013-04-01

We developed a high power mode-locked Nd:GdVO4 oscillator with low timing jitter directly pumped by an 879 nm diode. Under the absorbed pump power of 13.8 W, a maximum output power of 5.68 W at 1063 nm was obtained with a repetition rate of ˜250 MHz, corresponding to a slope efficiency of 78.7%. The measured pulse width and root mean square timing jitter at the output power of 5.35 W were 7.4 ps and 286 fs, respectively. To the best of our knowledge, this is the highest output power for a picosecond Nd:GdVO4 oscillator with low timing jitter.

G-jitter Effects on Transport and Pattern Formation

NASA Technical Reports Server (NTRS)

Schatz, Michael F.

2003-01-01

The research performed under this grant has led to an number of new insights into two general categories of fluid flows in the presence of time-dependent acceleration, as outlined briefly below. These results have been widely communicated in the scientific community through seven presentations at international conferences (4 invited, 3 contributed), five published papers (4 journal articles and 1 conference proceeding), and images from the research featured on the cover of all 2003 editions of the research journal, Nonlinearity. The work performed under this proposal also contained a substantial educational component by contributed significantly to the scientific training of one postdoctoral associate, one Ph.D. student and five undergraduate researchers. One main area of focus in this research was convective flow with time-dependent acceleration. Convection is one class of behavior that can arise from g-jitter effects. Our research focused on studies of Rayleigh-Benard system, which is an important model for understanding thermal convection; studies of this problem in the presence of acceleration modulations provided insight into the nature of g-jitter induced flow and of the effects of modulation and noise on non-equilibrium pattern formation. Our experiments on vertically vibrated Rayleigh-Benard convection demonstrated the existence of two classes of pure flow patterns (synchronous & subharmonic) patterns) that had long been predicted by theory but never before observed experimentally. Detailed studies of ranges of parameters where both classes of patterns exist simultaneously led to the discovery of a new type of patterns (called superlattices) in systems driven out of thermodynamic equilibrium.

100 km differential phase shift quantum key distribution experiment with low jitter up-conversion detectors

NASA Astrophysics Data System (ADS)

Diamanti, Eleni; Takesue, Hiroki; Langrock, Carsten; Fejer, M. M.; Yamamoto, Yoshihisa

2006-12-01

We present a quantum key distribution experiment in which keys that were secure against all individual eavesdropping attacks allowed by quantum mechanics were distributed over 100 km of optical fiber. We implemented the differential phase shift quantum key distribution protocol and used low timing jitter 1.55 µm single-photon detectors based on frequency up-conversion in periodically poled lithium niobate waveguides and silicon avalanche photodiodes. Based on the security analysis of the protocol against general individual attacks, we generated secure keys at a practical rate of 166 bit/s over 100 km of fiber. The use of the low jitter detectors also increased the sifted key generation rate to 2 Mbit/s over 10 km of fiber.

Gigahertz repetition rate, sub-femtosecond timing jitter optical pulse train directly generated from a mode-locked Yb:KYW laser.

PubMed

Yang, Heewon; Kim, Hyoji; Shin, Junho; Kim, Chur; Choi, Sun Young; Kim, Guang-Hoon; Rotermund, Fabian; Kim, Jungwon

2014-01-01

We show that a 1.13 GHz repetition rate optical pulse train with 0.70 fs high-frequency timing jitter (integration bandwidth of 17.5 kHz-10 MHz, where the measurement instrument-limited noise floor contributes 0.41 fs in 10 MHz bandwidth) can be directly generated from a free-running, single-mode diode-pumped Yb:KYW laser mode-locked by single-wall carbon nanotube-coated mirrors. To our knowledge, this is the lowest-timing-jitter optical pulse train with gigahertz repetition rate ever measured. If this pulse train is used for direct sampling of 565 MHz signals (Nyquist frequency of the pulse train), the jitter level demonstrated would correspond to the projected effective-number-of-bit of 17.8, which is much higher than the thermal noise limit of 50 Ω load resistance (~14 bits).

Design of optical axis jitter control system for multi beam lasers based on FPGA

NASA Astrophysics Data System (ADS)

Ou, Long; Li, Guohui; Xie, Chuanlin; Zhou, Zhiqiang

2018-02-01

A design of optical axis closed-loop control system for multi beam lasers coherent combining based on FPGA was introduced. The system uses piezoelectric ceramics Fast Steering Mirrors (FSM) as actuator, the Fairfield spot detection of multi beam lasers by the high speed CMOS camera for optical detecting, a control system based on FPGA for real-time optical axis jitter suppression. The algorithm for optical axis centroid detecting and PID of anti-Integral saturation were realized by FPGA. Optimize the structure of logic circuit by reuse resource and pipeline, as a result of reducing logic resource but reduced the delay time, and the closed-loop bandwidth increases to 100Hz. The jitter of laser less than 40Hz was reduced 40dB. The cost of the system is low but it works stably.

Stochastic mechanical model of vocal folds for producing jitter and for identifying pathologies through real voices.

PubMed

Cataldo, E; Soize, C

2018-06-06

Jitter, in voice production applications, is a random phenomenon characterized by the deviation of the glottal cycle length with respect to a mean value. Its study can help in identifying pathologies related to the vocal folds according to the values obtained through the different ways to measure it. This paper aims to propose a stochastic model, considering three control parameters, to generate jitter based on a deterministic one-mass model for the dynamics of the vocal folds and to identify parameters from the stochastic model taking into account real voice signals experimentally obtained. To solve the corresponding stochastic inverse problem, the cost function used is based on the distance between probability density functions of the random variables associated with the fundamental frequencies obtained by the experimental voices and the simulated ones, and also on the distance between features extracted from the voice signals, simulated and experimental, to calculate jitter. The results obtained show that the model proposed is valid and some samples of voices are synthesized considering the identified parameters for normal and pathological cases. The strategy adopted is also a novelty and mainly because a solution was obtained. In addition to the use of three parameters to construct the model of jitter, it is the discussion of a parameter related to the bandwidth of the power spectral density function of the stochastic process to measure the quality of the signal generated. A study about the influence of all the main parameters is also performed. The identification of the parameters of the model considering pathological cases is maybe of all novelties introduced by the paper the most interesting. Copyright © 2018 Elsevier Ltd. All rights reserved.

Functional outcomes of endoscopic arytenoid abduction lateropexy for unilateral vocal cord paralysis with dyspnea.

PubMed

Matievics, Vera; Bach, Adam; Sztano, Balazs; Bere, Zsofia; Tobias, Zoltan; Castellanos, Paul F; Mueller, Andreas H; Rovo, Laszló

2017-10-01

In unilateral vocal cord paralysis (UVCP), hoarseness is usually the leading symptom; however, the diminished airway might lead to breathing problems as well, especially with exertion. The application of the classic resection glottis enlarging or medialization procedures might shift the breathing and/or the voice to a worse condition. The non-destructive endoscopic arytenoid abduction lateropexy (EAAL) might be a solution for this problem. The aim of our study was to analyze the phonatory and respiratory outcomes of this treatment concept. The first year phoniatric [Jitter, Shimmer, harmonics-to-noise ratio (HNR), maximum phonation time (MPT), fundamental frequency (F 0 ), Voice Handicap Index (VHI), Dysphonia Severity Index (DSI), Global-Roughness-Breathiness scale (GRB)], peak inspiratory flow (PIF), and quality of life (QoL) were evaluated in ten UVCP patients treated by EAAL for dyspnea generally presented on exertion. PIF, Jitter, QoL, GRB, and VHI significantly improved. DSI, HNR, and MPT got non-significantly better. F 0 slightly increased in all patients, a mild deterioration of shimmer was observed. These results prove that improving respiratory function is not necessarily associated with a deterioration in voice quality. The EAAL provides a significant improvement in breathing and the vibratory parameters of the postoperative, more tensed and straightened vocal cords proved to be more advantageous than the original (para) median 'loose' position. The over-adduction of the contralateral side more or less compensates for the disadvantageous, more lateral position of the operated side. EAAL might be an alternative treatment for unilateral vocal cord paralysis associated with breathing problems.

Effects of type II thyroplasty on adductor spasmodic dysphonia.

PubMed

Sanuki, Tetsuji; Yumoto, Eiji; Minoda, Ryosei; Kodama, Narihiro

2010-04-01

Type II thyroplasty, or laryngeal framework surgery, is based on the hypothesis that the effect of adductor spasmodic dysphonia (AdSD) on the voice is due to excessively tight closure of the glottis, hampering phonation. Most of the previous, partially effective treatments have aimed to relieve this tight closure, including recurrent laryngeal nerve section or avulsion, extirpation of the adductor muscle, and botulinum toxin injection, which is currently the most popular. The aim of this study was to assess the effects of type II thyroplasty on aerodynamic and acoustic findings in patients with AdSD. Case series. University hospital. Ten patients with AdSD underwent type II thyroplasty between August 2006 and December 2008. Aerodynamic and acoustic analyses were performed prior to and six months after surgery. Mean flow rates (MFRs) and voice efficiency were evaluated with a phonation analyzer. Jitter, shimmer, the harmonics-to-noise ratio (HNR), standard deviation of the fundamental frequency (SDF0), and degree of voice breaks (DVB) were measured from each subject's longest sustained phonation sample of the vowel /a/. Voice efficiency improved significantly after surgery. No significant difference was found in the MFRs between before and after surgery. Jitter, shimmer, HNR, SDF0, and DVB improved significantly after surgery. Treatment of AdSD with type II thyroplasty significantly improved aerodynamic and acoustic findings. The results of this study suggest that type II thyroplasty provides relief from voice strangulation in patients with AdSD. Copyright 2010 American Academy of Otolaryngology-Head and Neck Surgery Foundation. Published by Mosby, Inc. All rights reserved.

Dynamic/Jitter Assessment of Multiple Potential HabEx Structural Designs

NASA Technical Reports Server (NTRS)

Knight, J. Brent; Stahl, H. Philip; Singleton, Andrew William; Hunt, Ronald A.; Therrell, Melissa F.; Caldwell, Mary Kathryn; Garcia, Jay Clarke

2017-01-01

The 2020 Decadal Survey in Astronomy and Astrophysics will assess candidate large missions to follow James Webb Space Telescope (JWST) and Wide Field Infrared Space Telescope (WFIRST). One candidate mission is the Habitable ExoPlanet Imaging Mission (HabEx). This presentation describes two HabEx structural designs and results from structural dynamic analyses performed to predict Primary Mirror (PM) Secondary Mirror (SM) Line of Site (LOS) stability (jitter) due to Reaction Wheel Assembly (RWA) vibrations.

Removal of jitter noise in 3D shape recovery from image focus by using Kalman filter.

PubMed

Jang, Hoon-Seok; Muhammad, Mannan Saeed; Choi, Tae-Sun

2018-02-01

In regard to Shape from Focus, one critical factor impacting system application is mechanical vibration of the translational stage causing jitter noise along the optical axis. This noise is not detectable by simply observing the image. However, when focus measures are applied, inaccuracies in the depth occur. In this article, jitter noise and focus curves are modeled by Gaussian distribution and quadratic function, respectively. Then Kalman filter is designed and applied to eliminate this noise in the focus curves, as a post-processing step after the focus measure application. Experiments are implemented with simulated objects and real objects to show usefulness of proposed algorithm. © 2017 Wiley Periodicals, Inc.

Low-Timing-Jitter Near-Infrared Single-Photon-Sensitive 16-Channel Intensified-Photodiode Detector

NASA Technical Reports Server (NTRS)

Krainak, Michael A.; Lu, Wei; Yang, Guangning; Sun, Xiaoli; Sykora, Derek; Jurkovic, Mike; Aebi, Verle; Costello, Ken; Burns, Richard

2011-01-01

We developed a 16-channel InGaAsP photocathode intensified-photodiode (IPD) detector with 78 ps (1-sigma) timing-jitter, less than 500 ps FWHM impulse response, greater than 15% quantum efficiency at 1064 nm wavelength with 131 kcps dark counts at 15 C.

Jitter reduction of a reaction wheel by management of angular momentum using magnetic torquers in nano- and micro-satellites

NASA Astrophysics Data System (ADS)

Inamori, Takaya; Wang, Jihe; Saisutjarit, Phongsatorn; Nakasuka, Shinichi

2013-07-01

Nowadays, nano- and micro-satellites, which are smaller than conventional large satellites, provide access to space to many satellite developers, and they are attracting interest as an application of space development because development is possible over shorter time period at a lower cost. In most of these nano- and micro-satellite missions, the satellites generally must meet strict attitude requirements for obtaining scientific data under strict constraints of power consumption, space, and weight. In many satellite missions, the jitter of a reaction wheel degrades the performance of the mission detectors and attitude sensors; therefore, jitter should be controlled or isolated to reduce its effect on sensor devices. In conventional standard-sized satellites, tip-tilt mirrors (TTMs) and isolators are used for controlling or isolating the vibrations from reaction wheels; however, it is difficult to use these devices for nano- and micro-satellite missions under the strict power, space, and mass constraints. In this research, the jitter of reaction wheels is reduced by using accurate sensors, small reaction wheels, and slow rotation frequency reaction wheel instead of TTMs and isolators. The objective of a reaction wheel in many satellite missions is the management of the satellite's angular momentum, which increases because of attitude disturbances. If the magnitude of the disturbance is reduced in orbit or on the ground, the magnitude of the angular momentum that the reaction wheels gain from attitude disturbances in orbit becomes smaller; therefore, satellites can stabilize their attitude using only smaller reaction wheels or slow rotation speed, which cause relatively smaller vibration. In nano- and micro-satellite missions, the dominant attitude disturbance is a magnetic torque, which can be cancelled by using magnetic actuators. With the magnetic compensation, the satellite reduces the angular momentum that the reaction wheels gain, and therefore, satellites do

A novel fair active queue management algorithm based on traffic delay jitter

NASA Astrophysics Data System (ADS)

Wang, Xue-Shun; Yu, Shao-Hua; Dai, Jin-You; Luo, Ting

2009-11-01

In order to guarantee the quantity of data traffic delivered in the network, congestion control strategy is adopted. According to the study of many active queue management (AQM) algorithms, this paper proposes a novel active queue management algorithm named JFED. JFED can stabilize queue length at a desirable level by adjusting output traffic rate and adopting a reasonable calculation of packet drop probability based on buffer queue length and traffic jitter; and it support burst packet traffic through the packet delay jitter, so that it can traffic flow medium data. JFED impose effective punishment upon non-responsible flow with a full stateless method. To verify the performance of JFED, it is implemented in NS2 and is compared with RED and CHOKe with respect to different performance metrics. Simulation results show that the proposed JFED algorithm outperforms RED and CHOKe in stabilizing instantaneous queue length and in fairness. It is also shown that JFED enables the link capacity to be fully utilized by stabilizing the queue length at a desirable level, while not incurring excessive packet loss ratio.

[Voice assessment and demographic data of applicants for a school of speech therapists].

PubMed

Reiter, R; Brosch, S

2008-05-01

Demographic data, subjective und objective voice analysis as well as self-assessment of voice quality from applicants for a school of speech therapists were investigated. Demographic data from 116 applicants were collected and their voice quality assessed by three independent judges. An objective evaluation was done by maximum phonation time, average fundamental frequency, dynamic range and percent of jitter and shimmer by means of Goettinger Hoarseness diagram. Self-assessment of voice quality was done by "voice handicap index questionnaire". The twenty successful applicants had a physiological voice in 95 %, they were all musical and had university entrance qualifications. Subjective voice assessment showed in 16 % of the applicants a hoarse voice. In this subgroup an unphysiological vocal use was observed in 72 % and a reduced articulation in 45 %. The objective voice parameters did not show a significant difference between the 3 groups. Self-assessment of the voice was inconspicuous in all applicants. Applicants with general qualification for university entrance, musicality and a physiological voice were more likely to be successful. There were main differences between self assessment of voice and quantitative analysis or subjective assessment by three independent judges.

All fiber-coupled, long-term stable timing distribution for free-electron lasers with few-femtosecond jitter

PubMed Central

Şafak, K.; Xin, M.; Callahan, P. T.; Peng, M. Y.; Kärtner, F. X.

2015-01-01

We report recent progress made in a complete fiber-optic, high-precision, long-term stable timing distribution system for synchronization of next generation X-ray free-electron lasers. Timing jitter characterization of the master laser shows less than 170-as RMS integrated jitter for frequencies above 10 kHz, limited by the detection noise floor. Timing stabilization of a 3.5-km polarization-maintaining fiber link is successfully achieved with an RMS drift of 3.3 fs over 200 h of operation using all fiber-coupled elements. This all fiber-optic implementation will greatly reduce the complexity of optical alignment in timing distribution systems and improve the overall mechanical and timing stability of the system. PMID:26798814

Pointing and Jitter Control for the USNA Multi-Beam Combining System

DTIC Science & Technology

2013-05-10

previous work, an adaptive H-infinity optimal controller has been developed to control a single beam using a beam position detector for feedback... turbulence and airborne particles, platform jitter, lack of feedback from the target , and current laser technology represent just a few of these...lasers. Solid state lasers, however, cannot currently provide high enough power levels to destroy a target using a single beam. On solid-state

Low-jitter high-power thyristor array pulse driver and generator

DOEpatents

Hanks, Roy L.

2002-01-01

A method and apparatus for generating low-jitter, high-voltage and high-current pulses for driving low impedance loads such as detonator fuses uses a MOSFET driver which, when triggered, discharges a high-voltage pre-charged capacitor into the primary of a toroidal current-multiplying transformer with multiple isolated secondary windings. The secondary outputs are suitable for driving an array of thyristors that discharge a precharged high-voltage capacitor and thus generating the required high-voltage and high-current pulse.

Inhaled beclomethasone dipropionate improves acoustic measures of voice in patients with asthma.

PubMed

Balter, M S; Adams, S G; Chapman, K R

2001-12-01

Inhaled corticosteroids have the potential to produce upper-airway side effects such as hoarseness. As new compounds and delivery devices are developed and compared, it is difficult to quantify their adverse upper-airway effects. We undertook the following study to test the ability of an acoustic analysis technique to quantify changes in vocal function in steroid-naive patients with asthma who receive inhaled beclomethasone dipropionate (BDP), 1,000 microg/d for 4 months. Patients self-administered one of four regimens of inhaled BDP. Group 1 patients received one 250-microg puff qid via metered-dose inhaler (MDI); group 2 patients received one 250-microg puff qid via MDI with a holding chamber; group 3 patients received two 250-microg puffs bid via MDI; and group 4 patients received two 250-microg puffs bid via MDI with a holding chamber. A smaller cohort of nonsmoking asthmatic patients was managed without steroid intervention for 4 months. At baseline and again at 8 weeks and 16 weeks after the initiation of BDP treatment, patients underwent spirometry and methacholine challenge. At baseline and again at 2, 4, 8, 12, and 16 weeks, patients underwent voice recording for analysis of voice parameters. The recorded vowels were low-pass filtered (10 KHz), digitized (22 KHz), and analyzed by software to obtain two acoustic measures: (1) jitter, the cycle-to-cycle variation in the time period of the voice signal; and (2) shimmer, the cycle-to-cycle variation in voice signal amplitude. We recruited 77 patients for randomization to inhaled steroid therapy and 10 patients who continued to receive only occasional inhaled bronchodilator therapy. In all active treatment groups, FEV(1), FVC, and provocative concentration of methacholine causing a 20% fall in FEV(1) improved significantly after BDP treatment. Mean jitter scores, a measurement of variation in voice pitch, were not significantly influenced by BDP treatment. However, mean shimmer scores, a reflection of

Jitter-correction for IR/UV-XUV pump-probe experiments at the FLASH free-electron laser

DOE PAGES

Savelyev, Evgeny; Boll, Rebecca; Bomme, Cedric; ...

2017-04-10

In pump-probe experiments employing a free-electron laser (FEL) in combination with a synchronized optical femtosecond laser, the arrival-time jitter between the FEL pulse and the optical laser pulse often severely limits the temporal resolution that can be achieved. Here, we present a pump-probe experiment on the UV-induced dissociation of 2,6-difluoroiodobenzene C 6H 3F 2I) molecules performed at the FLASH FEL that takes advantage of recent upgrades of the FLASH timing and synchronization system to obtain high-quality data that are not limited by the FEL arrival-time jitter. Here, we discuss in detail the necessary data analysis steps and describe the originmore » of the time-dependent effects in the yields and kinetic energies of the fragment ions that we observe in the experiment.« less

Comparison of effects on voice of diode laser and cold knife microlaryngology techniques for vocal fold polyps.

PubMed

Karasu, Mehmet Fatih; Gundogdu, Ramazan; Cagli, Sedat; Aydin, Mesut; Arli, Turan; Aydemir, Samet; Yuce, Imdat

2014-05-01

To compare the effects on voice of endolaryngeal microsurgery (EMS) with cold instruments and a new method, "diode laser," for vocal fold polyps. Fifty-one patients with vocal fold polyps suffering from dysphonia who were treated in the Erciyes University Department of Otolaryngology were included in the study. Voice analysis was performed in a soundproof room, holding the microphone 15 cm away from the patients' mouth and by recording a sustained [a] vowel for at least 10 seconds. Fundamental frequency (F0), Jitter, Shimmer, and noise-to-harmonic ratio (NHR) parameters were evaluated in terms of vocal analysis. All patients were asked for to fill in a questionnaire, after being informed about the voice handicap index (VHI). EMS was performed with a diode laser and cold knife on 26 and 25 patients, respectively. Patient follow-up was performed 8 weeks after surgery. Changes in F0, Jitter, Shimmer, and NHR values were measured and recorded. VHI was also completed and reassessed. There was a significant difference in each technique's VHI score between the preoperative and postoperative questionnaire (P < 0.001). Postoperatively, there was no significant difference in VHI scores between two groups (P > 0.05). There was a significant difference in voice analysis values measured preoperatively and at the postoperative controls for both groups (P < 0.05). Postoperatively, there was no significant difference in voice analysis values between two groups (P > 0.05). In the treatment of vocal polyps, EMS with both diode laser and traditional cold knife is effective. Copyright © 2014 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

G-Jitter Effects in Protein Crystal Growth - A Numerical Study

NASA Technical Reports Server (NTRS)

Ramachandran, N.; Baugher, C. R.

1995-01-01

The impact of spacecraft acceleration environment on Protein Crystal Growth (PCG) is studied. A brief overview of the Space Shuttle acceleration environment is provided followed by a simple scaling procedure used to obtain estimates of the flow and concentration field characteristics in PCG. A detailed two-dimensional numerical model is then used to simulate the PCG system response to different disturbance scenarios; viz. residual g effects, impulse type disturbances and oscillatory inputs. The results show that PCG is susceptible to g-jitter and is a good candidate for vibration isolation.

Somatosensory spatial attention modulates amplitudes, latencies, and latency jitter of laser-evoked brain potentials.

PubMed

Franz, Marcel; Nickel, Moritz M; Ritter, Alexander; Miltner, Wolfgang H R; Weiss, Thomas

2015-04-01

Several studies provided evidence that the amplitudes of laser-evoked potentials (LEPs) are modulated by attention. However, previous reports were based on across-trial averaging of LEP responses at the expense of losing information about intertrial variability related to attentional modulation. The aim of this study was to investigate the effects of somatosensory spatial attention on single-trial parameters (i.e., amplitudes, latencies, and latency jitter) of LEP components (N2 and P2). Twelve subjects participated in a sustained spatial attention paradigm while noxious laser stimuli (left hand) and noxious electrical stimuli (right hand) were sequentially delivered to the dorsum of the respective hand with nonnoxious air puffs randomly interspersed within the sequence of noxious stimuli. Participants were instructed to mentally count all stimuli (i.e., noxious and nonnoxious) applied to the attended location. Laser stimuli, presented to the attended hand (ALS), elicited larger single-trial amplitudes of the N2 component compared with unattended laser stimuli (ULS). In contrast, single-trial amplitudes of the P2 component were not significantly affected by spatial attention. Single-trial latencies of the N2 and P2 were significantly smaller for ALS vs. ULS. Additionally, the across-trial latency jitter of the N2 component was reduced for ALS. Conversely, the latency jitter of the P2 component was smaller for ULS compared with ALS. With the use of single-trial analysis, the study provided new insights into brain dynamics of LEPs related to spatial attention. Our results indicate that single-trial parameters of LEP components are differentially modulated by spatial attention. Copyright © 2015 the American Physiological Society.

Femtosecond timing-jitter between photo-cathode laser and ultra-short electron bunches by means of hybrid compression

NASA Astrophysics Data System (ADS)

Pompili, R.; Anania, M. P.; Bellaveglia, M.; Biagioni, A.; Castorina, G.; Chiadroni, E.; Cianchi, A.; Croia, M.; Di Giovenale, D.; Ferrario, M.; Filippi, F.; Gallo, A.; Gatti, G.; Giorgianni, F.; Giribono, A.; Li, W.; Lupi, S.; Mostacci, A.; Petrarca, M.; Piersanti, L.; Di Pirro, G.; Romeo, S.; Scifo, J.; Shpakov, V.; Vaccarezza, C.; Villa, F.

2016-08-01

The generation of ultra-short electron bunches with ultra-low timing-jitter relative to the photo-cathode (PC) laser has been experimentally proved for the first time at the SPARC_LAB test-facility (INFN-LNF, Frascati) exploiting a two-stage hybrid compression scheme. The first stage employs RF-based compression (velocity-bunching), which shortens the bunch and imprints an energy chirp on it. The second stage is performed in a non-isochronous dogleg line, where the compression is completed resulting in a final bunch duration below 90 fs (rms). At the same time, the beam arrival timing-jitter with respect to the PC laser has been measured to be lower than 20 fs (rms). The reported results have been validated with numerical simulations.

Young Nearby Suns and Stellar Jitter Dependence on Age

NASA Astrophysics Data System (ADS)

Cabrera, Nicole; White, Russel; Delfosse, Xavier; Noah Quinn, Samuel; Latham, David W.

2015-01-01

Finding the nearest young planets offers the most direct way to improve our understanding of how planets form, how they migrate, and how they evolve. However, most radial velocity (RV) surveys have avoided young stars because of their problematic characteristics, including high levels of stellar activity. Recent advancements in infrared (IR) detectors as well as wavelength calibration methods have provided new ways of pursuing high-precision RV measurements of young stars. While this work has been successfully applied to many young late-K and M dwarfs, much less RV work has been done on young Sun-like stars, with the very recent exception of adolescent stars (~600 Myr) in open clusters. In order to better understand the dynamical and structural forces that shaped our own Solar system, we must begin to explore the more massive realm of Sun-like stars.We present precision optical radial velocity data of 5 young, nearby, Sun-like stars in AB Dor and assess our ability to detect young planets with current spectroscopic methods. The data were obtained with the TRES spectrograph on the 1.5-m Tillinghast Reflector at the Fred L. Whipple Observatory and with SOPHIE on the 1.95 m Telescope at the Observatoire de Haute Provence. We obtained a RV precision of ~8 m/s with TRES and ~7 m/s precision with SOPHIE; average observed dispersions are 38 m/s and 33 m/s, respectively. We combine our results with spectroscopic data of Sun-like stars spanning a broad range of youthful ages (< 1 Gyr) from the literature to investigate the relationship between stellar jitter and stellar age. The results suggest that the jitter of Sun-like stars decreases below 100 m/s for stars older than ~30 Myr, which would enable the discovery of hot Jupiters orbiting these adolescent age stars.

A simple high-voltage high current spark gap with subnanosecond jitter triggered by femtosecond laser filamentation

NASA Astrophysics Data System (ADS)

Arantchouk, L.; Houard, A.; Brelet, Y.; Carbonnel, J.; Larour, J.; André, Y.-B.; Mysyrowicz, A.

2013-04-01

We describe a simple, sturdy, and reliable spark gap operating with air at atmospheric pressure and able to switch currents in excess of 10 kA with sub-nanosecond jitter. The spark gap is remotely triggered by a femtosecond laser filament.

Materials of acoustic analysis: sustained vowel versus sentence.

PubMed

Moon, Kyung Ray; Chung, Sung Min; Park, Hae Sang; Kim, Han Su

2012-09-01

Sustained vowel is a widely used material of acoustic analysis. However, vowel phonation does not sufficiently demonstrate sentence-based real-life phonation, and biases may occur depending on the test subjects intent during pronunciation. The purpose of this study was to investigate the differences between the results of acoustic analysis using each material. An individual prospective study. Two hundred two individuals (87 men and 115 women) with normal findings in videostroboscopy were enrolled. Acoustic analysis was done using the speech pattern element acquisition and display program. Fundamental frequency (Fx), amplitude (Ax), contact quotient (Qx), jitter, and shimmer were measured with sustained vowel-based acoustic analysis. Average fundamental frequency (FxM), average amplitude (AxM), average contact quotient (QxM), Fx perturbation (CFx), and amplitude perturbation (CAx) were measured with sentence-based acoustic analysis. Corresponding data of the two methods were compared with each other. SPSS (Statistical Package for the Social Sciences, Version 12.0; SPSS, Inc., Chicago, IL) software was used for statistical analysis. FxM was higher than Fx in men (Fx, 124.45 Hz; FxM, 133.09 Hz; P=0.000). In women, FxM seemed to be lower than Fx, but the results were not statistically significant (Fx, 210.58 Hz; FxM, 208.34 Hz; P=0.065). There was no statistical significance between Ax and AxM in both the groups. QxM was higher than Qx in men and women. Jitter was lower in men, but CFx was lower in women. Both Shimmer and CAx were higher in men. Sustained vowel phonation could not be a complete substitute for real-time phonation in acoustic analysis. Characteristics of acoustic materials should be considered when choosing the material for acoustic analysis and interpreting the results. Copyright © 2012 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

A review on high-resolution CMOS delay lines: towards sub-picosecond jitter performance.

PubMed

Abdulrazzaq, Bilal I; Abdul Halin, Izhal; Kawahito, Shoji; Sidek, Roslina M; Shafie, Suhaidi; Yunus, Nurul Amziah Md

2016-01-01

A review on CMOS delay lines with a focus on the most frequently used techniques for high-resolution delay step is presented. The primary types, specifications, delay circuits, and operating principles are presented. The delay circuits reported in this paper are used for delaying digital inputs and clock signals. The most common analog and digitally-controlled delay elements topologies are presented, focusing on the main delay-tuning strategies. IC variables, namely, process, supply voltage, temperature, and noise sources that affect delay resolution through timing jitter are discussed. The design specifications of these delay elements are also discussed and compared for the common delay line circuits. As a result, the main findings of this paper are highlighting and discussing the followings: the most efficient high-resolution delay line techniques, the trade-off challenge found between CMOS delay lines designed using either analog or digitally-controlled delay elements, the trade-off challenge between delay resolution and delay range and the proposed solutions for this challenge, and how CMOS technology scaling can affect the performance of CMOS delay lines. Moreover, the current trends and efforts used in order to generate output delayed signal with low jitter in the sub-picosecond range are presented.

Chromospheric activity and rotation of FGK stars in the solar vicinity. An estimation of the radial velocity jitter

NASA Astrophysics Data System (ADS)

Martínez-Arnáiz, R.; Maldonado, J.; Montes, D.; Eiroa, C.; Montesinos, B.

2010-09-01

Context. Chromospheric activity produces both photometric and spectroscopic variations that can be mistaken as planets. Large spots crossing the stellar disc can produce planet-like periodic variations in the light curve of a star. These spots clearly affect the spectral line profiles, and their perturbations alter the line centroids creating a radial velocity jitter that might “contaminate” the variations induced by a planet. Precise chromospheric activity measurements are needed to estimate the activity-induced noise that should be expected for a given star. Aims: We obtain precise chromospheric activity measurements and projected rotational velocities for nearby (d ≤ 25 pc) cool (spectral types F to K) stars, to estimate their expected activity-related jitter. As a complementary objective, we attempt to obtain relationships between fluxes in different activity indicator lines, that permit a transformation of traditional activity indicators, i.e., Ca ii H & K lines, to others that hold noteworthy advantages. Methods: We used high resolution (~50 000) echelle optical spectra. Standard data reduction was performed using the IRAF echelle package. To determine the chromospheric emission of the stars in the sample, we used the spectral subtraction technique. We measured the equivalent widths of the chromospheric emission lines in the subtracted spectrum and transformed them into fluxes by applying empirical equivalent width and flux relationships. Rotational velocities were determined using the cross-correlation technique. To infer activity-related radial velocity (RV) jitter, we used empirical relationships between this jitter and the R'_HK index. Results: We measured chromospheric activity, as given by different indicators throughout the optical spectra, and projected rotational velocities for 371 nearby cool stars. We have built empirical relationships among the most important chromospheric emission lines. Finally, we used the measured chromospheric activity

Interarytenoid muscle botox injection for treatment of adductor spasmodic dysphonia with vocal tremor.

PubMed

Kendall, Katherine A; Leonard, Rebecca J

2011-01-01

Up to one-third of patients presenting with adductor spasmodic dysphonia will have an associated vocal tremor. These patients may not respond fully to treatment using thyroarytenoid (TA) muscle botulinum toxin (Botox) injection. Treatment failures are attributed to the involvement of multiple muscle groups in the tremor. This study evaluates the results of combined interarytenoid (IA) and TA muscle Botox injection in a group of 27 patients with adductor spasmodic dysphonia and vocal tremor and in four patients with severe vocal tremor alone. Patient-satisfaction data were reviewed retrospectively. Pre- and postinjection acoustic data were collected prospectively. Acoustic measures of fundamental frequency and cycle-by-cycle variability in frequency (jitter) and intensity (shimmer) were obtained from 15 patients' sustained vowel productions. Measures were collected after TA muscle injection, alone, and after combined TA and IA (TA+IA) muscle injections. In addition, two experienced voice clinicians blindly assessed tremor severity from recordings made for each patient in the two conditions. Patients were also queried regarding their satisfaction with the results of the injections and whether they desired to continue receiving TA+IA treatment. Significant improvement in all acoustic measures except for % jitter was observed after the TA+IA muscle injections. Listeners identified voice samples after TA+IA muscle injections as demonstrating less tremor in 73% of the paired comparisons. Sixty-seven percent of the patients with spasmodic dysphonia and vocal tremor wished to continue to receive IA muscle injections. Only one patient with severe vocal tremor wished to continue with injections. The addition of an IA muscle Botox injection to the treatment of patients with a combination adductor spasmodic dysphonia and vocal tremor may improve voice outcomes. Copyright © 2011 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Sub-fs electron bunch generation with sub-10-fs bunch arrival-time jitter via bunch slicing in a magnetic chicane

NASA Astrophysics Data System (ADS)

Zhu, J.; Assmann, R. W.; Dohlus, M.; Dorda, U.; Marchetti, B.

2016-05-01

The generation of ultrashort electron bunches with ultrasmall bunch arrival-time jitter is of vital importance for laser-plasma wakefield acceleration with external injection. We study the production of 100-MeV electron bunches with bunch durations of subfemtosecond (fs) and bunch arrival-time jitters of less than 10 fs, in an S-band photoinjector by using a weak magnetic chicane with a slit collimator. The beam dynamics inside the chicane is simulated by using two codes with different self-force models. The first code separates the self-force into a three-dimensional (3D) quasistatic space-charge model and a one-dimensional coherent synchrotron radiation (CSR) model, while the other one starts from the first principle with a so-called 3D sub-bunch method. The simulations indicate that the CSR effect dominates the horizontal emittance growth and the 1D CSR model underestimates the final bunch duration and emittance because of the very large transverse-to-longitudinal aspect ratio of the sub-fs bunch. Particularly, the CSR effect is also strongly affected by the vertical bunch size. Due to the coupling between the horizontal and longitudinal phase spaces, the bunch duration at the entrance of the last dipole magnet of the chicane is still significantly longer than that at the exit of the chicane, which considerably mitigates the impact of space charge and CSR effects on the beam quality. Exploiting this effect, a bunch charge of up to 4.8 pC in a sub-fs bunch could be simulated. In addition, we analytically and numerically investigate the impact of different jitter sources on the bunch arrival-time jitter downstream of the chicane, and define the tolerance budgets assuming realistic values of the stability of the linac for different bunch charges and compression schemes.

a Novel Technique for Precision Geometric Correction of Jitter Distortion for the Europa Imaging System and Other Rolling-Shutter Cameras

NASA Astrophysics Data System (ADS)

Kirk, R. L.; Shepherd, M.; Sides, S. C.

2018-04-01

We use simulated images to demonstrate a novel technique for mitigating geometric distortions caused by platform motion ("jitter") as two-dimensional image sensors are exposed and read out line by line ("rolling shutter"). The results indicate that the Europa Imaging System (EIS) on NASA's Europa Clipper can likely meet its scientific goals requiring 0.1-pixel precision. We are therefore adapting the software used to demonstrate and test rolling shutter jitter correction to become part of the standard processing pipeline for EIS. The correction method will also apply to other rolling-shutter cameras, provided they have the operational flexibility to read out selected "check lines" at chosen times during the systematic readout of the frame area.

Detecting Motion from a Moving Platform; Phase 2: Lightweight, Low Power Robust Means of Removing Image Jitter

DTIC Science & Technology

2011-11-01

common housefly , Musca domestica. “Lightweight, Low Power Robust Means of Removing Image Jitter,” (AFRL-RX-TY-TR-2011-0096-02) develops an optimal...biological vision system of the common housefly , Musca domestica. Several variations of this sensor were designed, simulated extensively, and hardware

Practical application of cross correlation technique to measure jitter of master-oscillator-power-amplifier laser system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Młyńczak, J.; Sawicz-Kryniger, K.; Fry, A. R.

2014-01-01

The Linac coherent light source (LCLS) at the SLAC National Accelerator Laboratory (SLAC) is the world’s first hard X-ray free electron laser (XFEL) and is capable of producing high-energy, femtosecond duration X-ray pulses. A common technique to study fast timescale physical phenomena, various “pump/probe” techniques are used. In these techniques there are two lasers, one optical and one X-ray, that work as a pump and as a probe to study dynamic processes in atoms and molecules. In order to resolve phenomena that occur on femtosecond timescales, it is imperative to have very precise timing between the optical lasers and X-raysmore » (on the order of ~ 20 fs or better). The lasers are synchronized to the same RF source that drives the accelerator and produces the X-ray laser. However, elements in the lasers cause some drift and time jitter, thereby de-synchronizing the system. This paper considers cross-correlation technique as a way to quantify the drift and jitter caused by the regenerative amplifier of the ultrafast optical laser.« less

Perceptual evaluation and acoustic analysis of pneumatic artificial larynx.

PubMed

Xu, Jie Jie; Chen, Xi; Lu, Mei Ping; Qiao, Ming Zhe

2009-12-01

To investigate the perceptual and acoustic characteristics of the pneumatic artificial larynx (PAL) and evaluate its speech ability and clinical value. Prospective study. The study was conducted in the Voice Lab, Department of Otorhinolaryngology, The First Affiliated Hospital of Nanjing Medical University. Forty-six laryngectomy patients using the PAL were rated for intelligibility and fluency of speech. The voice signals of sustained vowel /a/ for 40 healthy controls and 42 successful patients using the PAL were measured by a computer system. The acoustic parameters and sound spectrographs were analyzed and compared between the two groups. Forty-two of 46 patients using the PAL (91.3%) acquired successful speech capability. The intelligibility scores of 42 successful PAL speakers ranged from 71 to 95 percent, and the intelligibility range of four unsuccessful speakers was 30 to 50 percent. The fluency was judged as good or excellent in 42 successful patients, and poor or fair in four unsuccessful patients. There was no significant difference in average fundamental frequency, maximum intensity, jitter, shimmer, and normalized noise energy (NNE) between 42 successful PAL speakers and 40 healthy controls, while the maximum phonation time (MPT) of PAL speakers was slightly lower than that of the controls. The sound spectrographs of the patients using the PAL approximated those of the healthy controls. The PAL has the advantage of a high percentage of successful vocal rehabilitation. PAL speech is fluent and intelligible. The acoustic characteristics of the PAL are similar to those of a normal voice.

Evaluation of type II thyroplasty on phonatory physiology in an excised canine larynx model

PubMed Central

Devine, Erin E.; Hoffman, Matthew R.; McCulloch, Timothy M.; Jiang, Jack J.

2016-01-01

Objective Type II thyroplasty is an alternative treatment for spasmodic dysphonia, addressing hyperadduction by incising and lateralizing the thyroid cartilage. We quantified the effect of lateralization width on phonatory physiology using excised canine larynges. Methods Normal closure, hyperadduction, and type II thyroplasty (lateralized up to 5mm at 1mm increments with hyperadducted arytenoids) were simulated in excised larynges (N=7). Aerodynamic, acoustic, and videokymographic data were recorded at three subglottal pressures relative to phonation threshold pressure (PTP). One-way repeated measures ANOVA assessed effect of condition on aerodynamic parameters. Random intercepts linear mixed effects models assessed effects of condition and subglottal pressure on acoustic and videokymographic parameters. Results PTP differed across conditions (p<0.001). Condition affected percent shimmer (p<0.005) but not percent jitter. Both pressure (p<0.03) and condition (p<0.001) affected fundamental frequency. Pressure affected vibratory amplitude (p<0.05) and intra-fold phase difference (p<0.05). Condition affected phase difference between the vocal folds (p<0.001). Conclusions Hyperadduction increased PTP and worsened perturbation compared to normal, with near normal physiology restored with 1mm lateralization. Further lateralization deteriorated voice quality and increased PTP. Acoustic and videokymographic results indicate that normal physiologic relationships between subglottal pressure and vibration are preserved at optimal lateralization width, but then degrade with further lateralization. The 1mm optimal width observed here is due to the small canine larynx size. Future human trials would likely demonstrate a greater optimal width, with patient-specific value potentially determined based on larynx size and symptom severity. PMID:27223665

The measurement of solute diffusion coefficients in dilute liquid alloys: the influence of unit gravity and g-jitter on buoyancy convection.

PubMed

Smith, R W; Yang, B J; Huang, W D

2004-11-01

Liquid diffusion experiments conducted on the MIR space station using the Canadian Space Agency QUELD II processing facility and the microgravity isolation mount (MIM) showed that g-jitter significantly increased the measured solute diffusion coefficients. In some experiments, milli-g forced vibration was superimposed on the sample when isolated from the ambient g-jitter; this resulted in markedly increased solute transport. To further explore the effects arising in these long capillary diffusion couples from the absence of unit-gravity and the presence of the forced g-jitter, the effects of a 1 milli-g forcing vibration on the mass transport in a 1.5 mm diameter long capillary diffusion couple have been simulated. In addition, to increase understanding of the role of unit gravity in determining the extent to which gravity can influence measured diffusion coefficient values, comparative experiments involving gold, silver, and antimony diffusing in liquid lead have been carried out using a similar QUELD II facility to that employed in the QUELD II/MIM/MIR campaign but under terrestrial conditions. It was found that buoyancy-driven convection may still persist in the liquid even when conditions are arranged for a continuously decreasing density gradient up the axis of a vertical long capillary diffusion couple due to the presence of small radial temperature gradients.

Integrating voice evaluation: correlation between acoustic and audio-perceptual measures.

PubMed

Vaz Freitas, Susana; Melo Pestana, Pedro; Almeida, Vítor; Ferreira, Aníbal

2015-05-01

This article aims to establish correlations between acoustic and audio-perceptual measures using the GRBAS scale with respect to four different voice analysis software programs. Exploratory, transversal. A total of 90 voice records were collected and analyzed with the Dr. Speech (Tiger Electronics, Seattle, WA), Multidimensional Voice Program (Kay Elemetrics, NJ, USA), PRAAT (University of Amsterdam, The Netherlands), and Voice Studio (Seegnal, Oporto, Portugal) software programs. The acoustic measures were correlated to the audio-perceptual parameters of the GRBAS and rated by 10 experts. The predictive value of the acoustic measurements related to the audio-perceptual parameters exhibited magnitudes ranging from weak (R(2)a=0.17) to moderate (R(2)a=0.71). The parameter exhibiting the highest correlation magnitude is B (Breathiness), whereas the weaker correlation magnitudes were found to be for A (Asthenia) and S (Strain). The acoustic measures with stronger predictive values were local Shimmer, harmonics-to-noise ratio, APQ5 shimmer, and PPQ5 jitter, with different magnitudes for each one of the studied software programs. Some acoustic measures are pointed as significant predictors of GRBAS parameters, but they differ among software programs. B (Breathiness) was the parameter exhibiting the highest correlation magnitude. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Acoustic changes in student actors' voices after 12 months of training.

PubMed

Walzak, Peta; McCabe, Patricia; Madill, Cate; Sheard, Christine

2008-05-01

This study was to evaluate acoustic changes in student actors' voices after 12 months of actor training. The design used was a longitudinal study. Eighteen students enrolled in an Australian tertiary 3-year acting program (nine male and nine female) were assessed at the beginning of their acting course and again 12 months later using a questionnaire, interview, maximum phonation time (MPT), reading, spontaneous speaking, sustained phonation tasks, and a pitch range task. Samples were analyzed for MPT, fundamental frequency across tasks, pitch range for speaking and reading, singing pitch range, noise-to-harmonic ratio, shimmer, and jitter. After training, measures of shimmer significantly increased for both male and female participants. Female participants' pitch range significantly increased after training, with a significantly lower mean frequency for their lowest pitch. The finding of limited or negative changes for some measures indicate that further investigation is required into the long-term effects of actor voice training and which parameters of voicing are most targeted and valued in training. Particular investigation into the relationship between training targets and outcomes could more reliably inform acting programs about changes in teaching methodologies. Further research into the relationship between specific training techniques, physiological changes, and vocal changes may also provide information on implementing more evidence-based training methods.

Impact of adenotonsillectomy on vocal emission in children.

PubMed

Dimatos, Spyros Cardoso; Neves, Luciano Rodrigues; Beltrame, Jéssica Monique; Azevedo, Renata Rangel; Pignatari, Shirley Shizue Nagata

2016-01-01

Adenotonsillectomy is the most common surgery performed by otolaryngologists in pediatric age, and one of the most frequently asked questions about the postoperative period is whether there is a potential for change in vocal pattern of these children. To evaluate the impact of adenotonsillectomy in the voice emission pattern of children with hypertrophy of palatine and pharyngeal tonsils. This is a prospective study in which we carried out perceptual auditory assessments and acoustic analysis of 26 children with adenotonsillar hypertrophy at three time points: before surgery, one month and three months after surgery. The following acoustic parameters were estimated using the Praat software: fundamental frequency, jitter, shimmer, and harmonic-noise ratio. A statistically significant change was found between shimmer and harmonic-noise ratio during vowel /u/ production between the preoperative and 1st month postoperative time points. No significant differences were detected for acoustic parameters between preoperative analysis and that of the 3rd month post-operation. Transient changes in acoustic parameters occur in children with adenotonsillar hypertrophy submitted to adenotonsillectomy, progressing to normalization in the 3rd postoperative month. Copyright © 2015 Associação Brasileira de Otorrinolaringologia e Cirurgia Cérvico-Facial. Published by Elsevier Editora Ltda. All rights reserved.

Design of a Sub-Picosecond Jitter with Adjustable-Range CMOS Delay-Locked Loop for High-Speed and Low-Power Applications

PubMed Central

Abdulrazzaq, Bilal I.; Ibrahim, Omar J.; Kawahito, Shoji; Sidek, Roslina M.; Shafie, Suhaidi; Yunus, Nurul Amziah Md.; Lee, Lini; Halin, Izhal Abdul

2016-01-01

A Delay-Locked Loop (DLL) with a modified charge pump circuit is proposed for generating high-resolution linear delay steps with sub-picosecond jitter performance and adjustable delay range. The small-signal model of the modified charge pump circuit is analyzed to bring forth the relationship between the DLL’s internal control voltage and output time delay. Circuit post-layout simulation shows that a 0.97 ps delay step within a 69 ps delay range with 0.26 ps Root-Mean Square (RMS) jitter performance is achievable using a standard 0.13 µm Complementary Metal-Oxide Semiconductor (CMOS) process. The post-layout simulation results show that the power consumption of the proposed DLL architecture’s circuit is 0.1 mW when the DLL is operated at 2 GHz. PMID:27690040

Smartphones Offer New Opportunities in Clinical Voice Research.

PubMed

Manfredi, C; Lebacq, J; Cantarella, G; Schoentgen, J; Orlandi, S; Bandini, A; DeJonckere, P H

2017-01-01

Smartphone technology provides new opportunities for recording standardized voice samples of patients and sending the files by e-mail to the voice laboratory. This drastically improves the collection of baseline data, as used in research on efficiency of voice treatments. However, the basic requirement is the suitability of smartphones for recording and digitizing pathologic voices (mainly characterized by period perturbations and noise) without significant distortion. In this experiment, two smartphones (a very inexpensive one and a high-level one) were tested and compared with direct microphone recordings in a soundproof room. The voice stimuli consisted in synthesized deviant voice samples (median of fundamental frequency: 120 and 200 Hz) with three levels of jitter and three levels of added noise. All voice samples were analyzed using PRAAT software. The results show high correlations between jitter, shimmer, and noise-to-harmonics ratio measured on the recordings via both smartphones, the microphone, and measured directly on the sound files from the synthesizer. Smartphones thus appear adequate for reliable recording and digitizing of pathologic voices. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Few-femtosecond-resolution characterization and suppression of excess timing jitter and drift in indoor atmospheric frequency comb transfer.

PubMed

Kang, Jinho; Shin, Junho; Kim, Chur; Jung, Kwangyun; Park, Suhyeon; Kim, Jungwon

2014-10-20

We characterize the timing jitter spectral density of the time-of-flight (TOF) in the indoor atmospheric transfer of optical pulse train over 10 decades of Fourier frequency range (10 μHz - 100 kHz) with sub-100-as resolution using a balanced optical cross-correlator (BOC). Based on the well-known theory for atmospheric transfer of a laser beam, we could fit the measured timing jitter power spectral density to the theory and analyze it with a fairly good agreement from 20 mHz to 10 Hz Fourier frequency range. Moreover, we demonstrate that the BOC-based timing stabilization method can suppress the excess fluctuations in timing from >200 fs (rms) to 2.6 fs (rms) maintained over 130 hours when an optical pulse train is transferred over a 76.2-m long free-space beam path in laboratory environment. The demonstrated stabilization result corresponds to 4 × 10(-20) overlapping Allan deviation at 117,000 s averaging time.

Perturbation of voice signals in register transitions on sustained frequency in professional tenors.

PubMed

Echternach, Matthias; Traser, Louisa; Richter, Bernhard

2012-09-01

Vocal register transitions in the passaggio region remain an unclarified field in classically trained male singers. We examined the acoustic and electroglottographic signals of seven tenors' transitions from voix mixte to falsetto on a sustained pitch F4 (349Hz) on the vowels /a, e, i, o, u, and æ/. It was found that in many of the tested subjects, register transitions between voix mixte and falsetto were performed very continuously without clear register transition events. However, an increase of frequency and amplitude perturbation (jitter, relative average perturbation, and shimmer) was observed during register transitions. These data suggest that professional tenors are able to avoid sudden registration events frequently observed in untrained voices. Copyright © 2012 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

An evaluation of 10 percent and 20 percent benzocaine gels in patients with acute toothaches

PubMed Central

Hersh, Elliot V.; Ciancio, Sebastian G.; Kuperstein, Arthur S.; Stoopler, Eric T.; Moore, Paul A.; Boynes, Sean G.; Levine, Steven C.; Casamassimo, Paul; Leyva, Rina; Mathew, Tanya; Shibly, Othman; Creighton, Paul; Jeffers, Gary E.; Corby, Patricia M.A.; Turetzky, Stanley N.; Papas, Athena; Wallen, Jillian; Idzik-Starr, Cynthia; Gordon, Sharon M.

2013-01-01

Background The authors evaluated the efficacy and tolerability of 10 percent and 20 percent benzocaine gels compared with those of a vehicle (placebo) gel for the temporary relief of toothache pain. They also assessed the compliance with the label dose administration directions on the part of participants with toothache pain. Methods Under double-masked conditions, 576 participants self-applied study gel to an open tooth cavity and surrounding oral tissues. Participants evaluated their pain intensity and pain relief for 120 minutes. The authors determined the amount of gel the participants applied. Results The responders’ rates (the primary efficacy parameter), defined as the percentage of participants who had an improvement in pain intensity as exhibited by a pain score reduction of at least one unit on the dental pain scale from baseline for two consecutive assessments any time between the five- and 20-minute points, were 87.3 percent, 80.7 percent and 70.4 percent, respectively, for 20 percent benzocaine gel, 10 percent benzocaine gel and vehicle gel. Both benzocaine gels were significantly (P ≤ .05) better than vehicle gel; the 20 percent benzocaine gel also was significantly (P ≤ .05) better than the 10 percent benzocaine gel. The mean amount of gel applied was 235.6 milligrams, with 88.2 percent of participants applying 400 mg or less. Conclusions Both 10 percent and 20 percent benzocaine gels were more efficacious than the vehicle gel, and the 20 percent benzocaine gel was more efficacious than the 10 percent benzocaine gel. All treatments were well tolerated by participants. Practical Implications Patients can use 10 percent and 20 percent benzocaine gels to temporarily treat toothache pain safely. PMID:23633700

A study of VHI scores and acoustic features in street vendors as occupational voice users.

PubMed

Natour, Yaser S; Darawsheh, Wesam B; Bashiti, Sara; Wari, Majd; Taha, Juhayna; Odeh, Thair

to investigate acoustic features of phonation and perception of voice handicap in street vendors. Eighty-eight participants (44 street vendors, 44 controls) were recruited. The mean age of the group was 38.9±16.0 years (range: 20-78 years). Scores of the Arabic version of the Voice Handicap Index (VHI-Arab) were used for analysis. Acoustic measures of fundamental frequency (F 0 ), jitter, shimmer, and signal-to-noise ratio (SNR) were also analyzed. Analysis showed a significant difference between street vendors and controls in the total score of the VHI-Arab (p<0.001) as well as scores of all three VHI-Arab subsections: functional (p<0.001), physical (p<0.001), and emotional (p=0.025). Weak correlations were found among all of the VHI scores and acoustic measures (-0.219≤ r≤0.355), except for SNR where a moderate negative correlations were found (r=-0.555; -0.4) between the VHI (physical and total) scores and SNR values. Significant differences also were found in F 0 , jitter, and SNR among specific subgroups of street vendors when stratified by weekly hours worked (p<0.05), and in jitter (p=0.39) when stratified by educational level. Perception of voice handicap and a possible effect on vocal quality in street vendors were noted. The effect of factors, namely work hours and educational level, on voice quality should be further studied. Copyright © 2017. Published by Elsevier Inc.

Agile Blocker and Clock Jitter Tolerant Low-Power Frequency Selective Receiver with Energy Harvesting Capability.

PubMed

Hasan, Abul; Helaoui, Mohamed; Ghannouchi, Fadhel M

2017-08-29

In this article, a novel tunable, blocker and clock jitter tolerant, low power, quadrature phase shift frequency selective (QPS-FS) receiver with energy harvesting capability is proposed. The receiver's design embraces and integrates (i) the baseband to radio frequency (RF) impedance translation concept to improve selectivity over that of conventional homodyne receiver topologies and (ii) broadband quadrature phase shift circuitry in the RF path to remove an active multi-phase clock generation circuit in passive mixer (PM) receivers. The use of a single local oscillator clock signal with a passive clock division network improves the receiver's robustness against clock jitter and reduces the source clock frequency by a factor of N, compared to PM receivers using N switches (N≥4). As a consequence, the frequency coverage of the QPS-FS receiver is improved by a factor of N, given a clock source of maximum frequency; and, the power consumption of the whole receiver system can eventually be reduced. The tunable QPS-FS receiver separates the wanted RF band signal from the unwanted blockers/interferers. The desired RF signal is frequency down-converted to baseband, while the undesired blocker/interferer signals are reflected by the receiver, collected and could be energy recycled using an auxiliary energy harvesting device.

Effect of signal jitter on the spectrum of rotor impulsive noise

NASA Technical Reports Server (NTRS)

Brooks, Thomas F.

1987-01-01

The effect of randomness or jitter of the acoustic waveform on the spectrum of rotor impulsive noise is studied because of its importance for data interpretation. An acoustic waveform train is modelled representing rotor impulsive noise. The amplitude, shape, and period between occurrences of individual pulses are allowed to be randomized assuming normal probability distributions. Results, in terms of the standard deviations of the variable quantities, are given for the autospectrum as well as special processed spectra designed to separate harmonic and broadband rotor noise components. Consideration is given to the effect of accuracy in triggering or keying to a rotor one per revolution signal. An example is given showing the resultant spectral smearing at the high frequencies due to the pulse signal period variability.

Effect of signal jitter on the spectrum of rotor impulsive noise

NASA Technical Reports Server (NTRS)

Brooks, Thomas F.

1988-01-01

The effect of randomness or jitter of the acoustic waveform on the spectrum of rotor impulsive noise is studied because of its importance for data interpretation. An acoustic waveform train is modeled representing rotor impulsive noise. The amplitude, shape, and period between occurrences of individual pulses are allowed to be randomized assuming normal probability distributions. Results, in terms of the standard deviations of the variable quantities, are given for the autospectrum as well as special processed spectra designed to separate harmonic and broadband rotor noise components. Consideration is given to the effect of accuracy in triggering or keying to a rotor one per revolution signal. An example is given showing the resultant spectral smearing at the high frequencies due to the pulse signal period variability.

Dynamic/Jitter Assessment of Multiple Potential HabEx Structural Designs

NASA Technical Reports Server (NTRS)

Knight, J. Brent; Stahl, H. Philip; Singleton, Andy; Hunt, Ron; Therrell, Melissa; Caldwell, Kate; Garcia, Jay; Baysinger, Mike

2017-01-01

One of the driving structural requirements of the Habitable Exo-Planet (HabEx) telescope is to maintain Line Of Sight (LOS) stability between the Primary Mirror (PM) and Secondary Mirror (SM) of = 5 mas. Dynamic analyses of two configurations of a proposed (HabEx) 4 meter off-axis telescope structure were performed to predict effects of jitter on primary/secondary mirror alignment. The dynamic disturbance used as the forcing function was the James Webb Space Telescope reaction wheel assembly vibration emission specification level. The objective of these analyses was to predict "order-of-magnitude" performance for various structural configurations which will roll into efforts to define the HabEx structural design's global architecture. Two variations of the basic architectural design were analyzed. Relative motion between the PM and the SM for each design configuration are reported.

GNSS software receiver sampling noise and clock jitter performance and impact analysis

NASA Astrophysics Data System (ADS)

Chen, Jian Yun; Feng, XuZhe; Li, XianBin; Wu, GuangYao

2015-02-01

In the design of a multi-frequency multi-constellation GNSS software defined radio receivers is becoming more and more popular due to its simple architecture, flexible configuration and good coherence in multi-frequency signal processing. It plays an important role in navigation signal processing and signal quality monitoring. In particular, GNSS software defined radio receivers driving the sampling clock of analogue-to-digital converter (ADC) by FPGA implies that a more flexible radio transceiver design is possible. According to the concept of software defined radio (SDR), the ideal is to digitize as close to the antenna as possible. Whereas the carrier frequency of GNSS signal is of the frequency of GHz, converting at this frequency is expensive and consumes more power. Band sampling method is a cheaper, more effective alternative. When using band sampling method, it is possible to sample a RF signal at twice the bandwidth of the signal. Unfortunately, as the other side of the coin, the introduction of SDR concept and band sampling method induce negative influence on the performance of the GNSS receivers. ADC's suffer larger sampling clock jitter generated by FPGA; and low sampling frequency introduces more noise to the receiver. Then the influence of sampling noise cannot be neglected. The paper analyzes the sampling noise, presents its influence on the carrier noise ratio, and derives the ranging error by calculating the synchronization error of the delay locked loop. Simulations aiming at each impact factors of sampling-noise-induced ranging error are performed. Simulation and experiment results show that if the target ranging accuracy is at the level of centimeter, the quantization length should be no less than 8 and the sampling clock jitter should not exceed 30ps.

Explaining the morphology of supernova remnant (SNR) 1987A with the jittering jets explosion mechanism

NASA Astrophysics Data System (ADS)

Bear, Ealeal; Soker, Noam

2018-07-01

We find that the remnant of supernova (SN) 1987A shares some morphological features with four supernova remnants (SNRs) that have signatures of shaping by jets, and from that we strengthen the claim that jets played a crucial role in the explosion of SN 1987A. Some of the morphological features appear also in planetary nebulae (PNe) where jets are observed. The clumpy ejecta brings us to support the claim that the jittering jets explosion mechanism can account for the structure of the remnant of SN 1987A, i.e. SNR 1987A. We conduct a preliminary attempt to quantify the fluctuations in the angular momentum of the mass that is accreted on to the newly born neutron star via an accretion disc or belt. The accretion disc/belt launches jets that explode core collapse supernovae (CCSNe). The relaxation time of the accretion disc/belt is comparable to the duration of a typicalfigu jet-launching episode in the jittering jets explosion mechanism, and hence the disc/belt has no time to relax. We suggest that this might explain the two unequal opposite jets that later lead to the unequal sides of the elongated structures in some SNRs of CCSNe. We reiterate our earlier call for a paradigm shift from a neutrino-driven explosion to a jet-driven explosion of CCSNe.

Explaining the morphology of supernova remnant (SNR) 1987A with the jittering jets explosion mechanism

NASA Astrophysics Data System (ADS)

Bear, Ealeal; Soker, Noam

2018-04-01

We find that the remnant of supernova (SN) 1987A shares some morphological features with four supernova remnants (SNRs) that have signatures of shaping by jets, and from that we strengthen the claim that jets played a crucial role in the explosion of SN 1987A. Some of the morphological features appear also in planetary nebulae (PNe) where jets are observed. The clumpy ejecta bring us to support the claim that the jittering jets explosion mechanism can account for the structure of the remnant of SN 1987A, i.e., SNR 1987A. We conduct a preliminary attempt to quantify the fluctuations in the angular momentum of the mass that is accreted on to the newly born neutron star via an accretion disk or belt. The accretion disk/belt launches the jets that explode core collapse supernovae (CCSNe). The relaxation time of the accretion disk/belt is comparable to the duration of a typical jet-launching episode in the jittering jets explosion mechanism, and hence the disk/belt has no time to relax. We suggest that this might explain two unequal opposite jets that later lead to unequal sides of the elongated structures in some SNRs of CCSNe. We reiterate our earlier call for a paradigm shift from neutrino-driven explosion to a jet-driven explosion of CCSNe.

Acoustic analyses of thyroidectomy-related changes in vowel phonation.

PubMed

Solomon, Nancy Pearl; Awan, Shaheen N; Helou, Leah B; Stojadinovic, Alexander

2012-11-01

Changes in vocal function that can occur after thyroidectomy were tracked with acoustic analyses of sustained vowel productions. The purpose was to determine which time-based or spectral/cepstral-based measures of two vowels were able to detect voice changes over time in patients undergoing thyroidectomy. Prospective, longitudinal, and observational clinical trial. Voice samples of sustained /ɑ/ and /i/ recorded from 70 adults before and approximately 2 weeks, 3 months, and 6 months after thyroid surgery were analyzed for jitter, shimmer, harmonic-to-noise ratio (HNR), cepstral peak prominence (CPP), low-to-high ratio of spectral energy (L/H ratio), and the standard deviations of CPP and L/H ratio. Three trained listeners rated vowel and sentence productions for the four data collection sessions for each participant. For analysis purposes, participants were categorized post hoc according to voice outcome (VO) at their first postthyroidectomy assessment session. Shimmer, HNR, and CPP differed significantly across sessions; follow-up analyses revealed the strongest effect for CPP. CPP for /ɑ/ and /i/ differed significantly between groups of participants with normal versus negative (adverse) VO and between the pre- and 2-week postthyroidectomy sessions for the negative VO group. HNR, CPP, and L/H ratio differed across vowels, but both /ɑ/ and /i/ were similarly effective in tracking voice changes over time and differentiating VO groups. This study indicated that shimmer, HNR, and CPP determined from vowel productions can be used to track changes in voice over time as patients undergo and subsequently recover from thyroid surgery, with CPP being the strongest variable for this purpose. Evidence did not clearly reveal whether acoustic voice evaluations should include both /ɑ/ and /i/ vowels, but they should specify which vowel is used to allow for comparisons across studies and multiple clinical assessments. Copyright © 2012 The Voice Foundation. All rights

Least-squares deconvolution of evoked potentials and sequence optimization for multiple stimuli under low-jitter conditions.

PubMed

Bardy, Fabrice; Dillon, Harvey; Van Dun, Bram

2014-04-01

Rapid presentation of stimuli in an evoked response paradigm can lead to overlap of multiple responses and consequently difficulties interpreting waveform morphology. This paper presents a deconvolution method allowing overlapping multiple responses to be disentangled. The deconvolution technique uses a least-squared error approach. A methodology is proposed to optimize the stimulus sequence associated with the deconvolution technique under low-jitter conditions. It controls the condition number of the matrices involved in recovering the responses. Simulations were performed using the proposed deconvolution technique. Multiple overlapping responses can be recovered perfectly in noiseless conditions. In the presence of noise, the amount of error introduced by the technique can be controlled a priori by the condition number of the matrix associated with the used stimulus sequence. The simulation results indicate the need for a minimum amount of jitter, as well as a sufficient number of overlap combinations to obtain optimum results. An aperiodic model is recommended to improve reconstruction. We propose a deconvolution technique allowing multiple overlapping responses to be extracted and a method of choosing the stimulus sequence optimal for response recovery. This technique may allow audiologists, psychologists, and electrophysiologists to optimize their experimental designs involving rapidly presented stimuli, and to recover evoked overlapping responses. Copyright © 2013 International Federation of Clinical Neurophysiology. All rights reserved.

Electro-Optic Time-to-Space Converter for Optical Detector Jitter Mitigation

NASA Technical Reports Server (NTRS)

Birnbaum, Kevin; Farr, William

2013-01-01

A common problem in optical detection is determining the arrival time of a weak optical pulse that may comprise only one to a few photons. Currently, this problem is solved by using a photodetector to convert the optical signal to an electronic signal. The timing of the electrical signal is used to infer the timing of the optical pulse, but error is introduced by random delay between the absorption of the optical pulse and the creation of the electrical one. To eliminate this error, a time-to-space converter separates a sequence of optical pulses and sends them to different photodetectors, depending on their arrival time. The random delay, called jitter, is at least 20 picoseconds for the best detectors capable of detecting the weakest optical pulses, a single photon, and can be as great as 500 picoseconds. This limits the resolution with which the timing of the optical pulse can be measured. The time-to-space converter overcomes this limitation. Generally, the time-to-space converter imparts a time-dependent momentum shift to the incoming optical pulses, followed by an optical system that separates photons of different momenta. As an example, an electro-optic phase modulator can be used to apply longitudinal momentum changes (frequency changes) that vary in time, followed by an optical spectrometer (such as a diffraction grating), which separates photons with different momenta into different paths and directs them to impinge upon an array of photodetectors. The pulse arrival time is then inferred by measuring which photodetector receives the pulse. The use of a time-to-space converter mitigates detector jitter and improves the resolution with which the timing of an optical pulse is determined. Also, the application of the converter enables the demodulation of a pulse position modulated signal (PPM) at higher bandwidths than using previous photodetector technology. This allows the creation of a receiver for a communication system with high bandwidth and high bits

Multi-parameter comparison of injection laryngoplasty, medialization laryngoplasty, and arytenoid adduction in an excised larynx model

PubMed Central

Hoffman, Matthew R.; Witt, Rachel E.; Chapin, William J.; McCulloch, Timothy M.; Jiang, Jack J.

2010-01-01

Objective Evaluate the effect of injection laryngoplasty (IL), medialization laryngoplasty (ML), and ML combined with arytenoid adduction (ML-AA) on acoustic, aerodynamic, and mucosal wave measurements in an excised larynx setup. Methods Measurements were recorded for eight excised canine larynges with simulated unilateral vocal fold paralysis (UVFP) before and after vocal fold injection with Cymetra. A second set of eight larynges was used to evaluate medialization laryngoplasty using a Silastic implant without and with arytenoid adduction. Results IL and ML led to comparable decreases in phonation threshold flow (PTF), phonation threshold pressure (PTP), and phonation threshold power (PTW). ML-AA led to significant decreases in PTF (p=0.008), PTP (p=0.008), and PTW (p=0.008). IL and ML led to approximately equal decreases in percent jitter and percent shimmer. ML-AA caused the greatest increase in signal to noise ratio (SNR). ML-AA discernibly decreased frequency (p=0.059); a clear trend was not observed for IL or ML. IL significantly reduced mucosal wave amplitude (p=0.002), while both ML and ML-AA increased it. All procedures significantly decreased glottal gap, with the most dramatic effects observed after ML-AA (p=0.004). Conclusions ML-AA led to the greatest improvements in phonatory parameters. IL was comparable to ML aerodynamically and acoustically, but caused detrimental changes to the mucosal wave. Incremental improvements in parameters recorded from the same larynx were observed after ML and ML-AA. To ensure optimal acoustic outcome, the arytenoid must be correctly rotated. This study provides objective support for the combined ML-AA procedure in tolerant patients. Evidence based medicine level Not applicable – animal study. PMID:20213797

Measurement of an image jitter of an extended incoherent radiation source

NASA Astrophysics Data System (ADS)

Lukin, V. P.; Nosov, V. V.

2017-06-01

A scheme of an image jitter measuring device, which uses an extended incoherent source as a radiation source, is presented. The efficiency of the measuring device is analysed analytically and numerically in order to justify the operation of the adaptive optical system that does not require special creation or formation of a reference source. The features of the formed image of incoherent radiation are considered, in particular from the point of view of its possible application for measuring the phase fluctuations of optical waves propagating in a turbulent atmosphere (the adaptive system monitors the image of a self-luminous object illuminated by extraneous sources). The possibility of utilising a Shack-Hartmann wavefront sensor in adaptive systems using the image of an arbitrary object (or its fragment) as a reference source is shown.

Effects of voice training and voice hygiene education on acoustic and perceptual speech parameters and self-reported vocal well-being in female teachers.

PubMed

Ilomaki, Irma; Laukkanen, Anne-Maria; Leppanen, Kirsti; Vilkman, Erkki

2008-01-01

Voice education programs may help in optimizing teachers' voice use. This study compared effects of voice training (VT) and voice hygiene lecture (VHL) in 60 randomly assigned female teachers. All 60 attended the lecture, and 30 completed a short training course in addition. Text reading was recorded in working environments and analyzed for fundamental frequency (F0), equivalent sound level (Leq), alpha ratio, jitter, shimmer, and perceptual quality. Self-reports of vocal well-being were registered. In the VHL group, increased F0 and difficulty of phonation and in the VT group decreased perturbation, increased alpha ratio, easier phonation, and improved perceptual and self-reported voice quality were found. Both groups equally self-reported increase of voice care knowledge. Results seem to indicate improved vocal well-being after training.

Predicting mutational change in the speaking voice of boys.

PubMed

Fuchs, Michael; Fröehlich, Matthias; Hentschel, Bettina; Stuermer, Ingo W; Kruse, Eberhard; Knauft, Daniel

2007-03-01

The authors investigated whether acoustic speaking voice analyses can be used to predict the beginning of mutation in 21 male members of a professional boys' choir. Over a period of 3 years before mutation, children were examined every 3 months by ear, nose, and throat (ENT) and phoniatric specialists. At the same time, the voice was evaluated acoustically using analysis features of the Goettingen Hoarseness Diagram (GHD). Irregularity component and noise component, jitter, shimmer, mean waveform correlation coefficient, and fundamental frequency were determined from recordings of the speaking voice. Significant changes of acoustic features appeared 7 and 5 months before mutation onset, which indicates that vocal function is already restricted 6 months before mutation onset. This acoustic voice analysis is therefore suitable to support the care of the professional singing voice.

Study of accent-based music speech protocol development for improving voice problems in stroke patients with mixed dysarthria.

PubMed

Kim, Soo Ji; Jo, Uiri

2013-01-01

Based on the anatomical and functional commonality between singing and speech, various types of musical elements have been employed in music therapy research for speech rehabilitation. This study was to develop an accent-based music speech protocol to address voice problems of stroke patients with mixed dysarthria. Subjects were 6 stroke patients with mixed dysarthria and they received individual music therapy sessions. Each session was conducted for 30 minutes and 12 sessions including pre- and post-test were administered for each patient. For examining the protocol efficacy, the measures of maximum phonation time (MPT), fundamental frequency (F0), average intensity (dB), jitter, shimmer, noise to harmonics ratio (NHR), and diadochokinesis (DDK) were compared between pre and post-test and analyzed with a paired sample t-test. The results showed that the measures of MPT, F0, dB, and sequential motion rates (SMR) were significantly increased after administering the protocol. Also, there were statistically significant differences in the measures of shimmer, and alternating motion rates (AMR) of the syllable /K$\\inve$/ between pre- and post-test. The results indicated that the accent-based music speech protocol may improve speech motor coordination including respiration, phonation, articulation, resonance, and prosody of patients with dysarthria. This suggests the possibility of utilizing the music speech protocol to maximize immediate treatment effects in the course of a long-term treatment for patients with dysarthria.

Picosecond 1064-nm fiber laser with tunable pulse width and low timing jitter

NASA Astrophysics Data System (ADS)

Tian, Wenyan; Zhang, Shukui

2018-02-01

We report an all-fiber, linearly polarized, 1.1-W, 1064-nm fiber laser based on a two-stage Ytterbium-doped fiber amplifier seeded by a gain-switched diode laser with tunable pulse width from 21 to 200 ps at repetition rates of 0.5-1.5 GHz. Timing jitter of our 1064-nm fiber laser was measured to be 0.60 ps over 10 Hz-40 MHz when the gain-switched diode laser was operated at a repetition rate of 0.5, 1, and 1.5 GHz. The fiber laser offers an excellent long term power stability of +/- 0.3% and wavelength stability of +/- 0.01 nm over 8 hours

Selected fretting-wear-resistant coatings for titanium - 6-percent-aluminum - 4-percent-vanadium alloy

NASA Technical Reports Server (NTRS)

Bill, R. C.

1976-01-01

A titanium - 6-percent-aluminum - 4-percent-vanadium alloy (Ti-6Al-4V) was subjected to fretting-wear exposures against uncoated Ti-6Al-4V as a baseline and against various coatings and surface treatments applied to Ti-6Al-4V. The coatings evaluated included plasma-sprayed tungsten carbide with 12 percent cobalt, aluminum oxide with 13 percent titanium oxide, chromium oxide, and aluminum bronze with 10 percent aromatic polyester; polymer-bonded polyimide, polyimide with graphite fluoride, polyimide with molybdenum disulfide (MoS2), and methyl phenyl silicone bonded MoS2, preoxidation surface treatment, a nitride surface treatment, and a sputtered MoS2 coating. Results of wear measurements on both the coated and uncoated surfaces after 300,000 fretting cycles indicated that the polyimide coating was the most wear resistant and caused the least wear to the uncoated mating surface.

A clinical evaluation of 10 percent vs. 15 percent carbamide peroxide tooth-whitening agents.

PubMed

Kihn, P W; Barnes, D M; Romberg, E; Peterson, K

2000-10-01

Agents with carbamide peroxide, or CP, in various concentrations are widely prescribed for at-home tooth whitening. It is not clear, however, if the more concentrated gels will whitening teeth to a greater extent, as no controlled clinical trials have been reported. The authors conducted a double-blind study of human subjects to evaluate whether a 15 percent CP tooth-whitening system was more effective than a 10 percent CP system, and to determine if tooth sensitivity increased with use of the higher concentration. The authors recruited 57 subjects with maxillary anterior teeth of shade A3 or darker (as gauged against a value-oriented shade guide). The subjects were 18 to 65 years of age and in good general and dental health. After matching the subjects by sex and age, the authors randomly assigned them to either a control group, which used a 10 percent CP whitening agent, or an experimental group, which used a 15 percent CP agent. The results indicated that there was no significant difference in shade change between the groups after one week of treatment (t = 1.455, P = .05), but there was a significant difference at the end of the treatment period (t = 2.303, P < .05), as well as two weeks after treatment concluded (t = 2.248, P < .05). There was no significant difference in sensitivity (t = 1.399, P > .05). There was a significant difference in color change between the 10 percent CP and 15 percent CP groups at the end of the study period. There was no significant difference in level of tooth sensitivity between the two groups, and the incidence was equal; there was, however, a significant difference in variability of tooth sensitivity between the two groups. If performed under the careful guidance of a dentist, at-home whitening is an effective treatment, regardless of whether 10 percent CP or 15 percent CP is used. There may be added color change and varying sensitivity with the use of 15 percent CP.

Carrier-envelope phase stabilization with sub-10 as residual timing jitter.

PubMed

Borchers, B; Koke, S; Husakou, A; Herrmann, J; Steinmeyer, G

2011-11-01

We demonstrate carrier-envelope phase (CEP) stabilization of a mode-locked Ti:sapphire oscillator with unprecedented timing jitter of eight attoseconds. The stabilization performance is obtained by a combination of two different stabilization approaches. In a first step the drift of the CEP is stabilized with a conventional feedback loop by means of controlling the oscillator pump power with an acousto-optic modulator (AOM). In a second step we utilize a recently developed feed-forward type stabilization scheme which has a much higher control bandwith. Here an acousto-optic frequency shifter (AOFS) produces the stabilized output in the first diffraction order. Moreover, we present numerical results on the optimization of the length of the photonic crystal fiber, which is used to generate an octave-spanning spectrum, in order to optimize the sensitivity in the f-to-2f interferometers.

Instantaneous speed jitter detection via encoder signal and its application for the diagnosis of planetary gearbox

NASA Astrophysics Data System (ADS)

Zhao, Ming; Jia, Xiaodong; Lin, Jing; Lei, Yaguo; Lee, Jay

2018-01-01

In modern rotating machinery, rotary encoders have been widely used for the purpose of positioning and dynamic control. The study in this paper indicates that, the encoder signal, after proper processing, can be also effectively used for the health monitoring of rotating machines. In this work, a Kurtosis-guided local polynomial differentiator (KLPD) is proposed to estimate the instantaneous angular speed (IAS) of rotating machines based on the encoder signal. Compared with the central difference method, the KLPD is more robust to noise and it is able to precisely capture the weak speed jitters introduced by mechanical defects. The fault diagnosis of planetary gearbox has proven to be a challenging issue in both industry and academia. Based on the proposed KLPD, a systematic method for the fault diagnosis of planetary gearbox is proposed. In this method, residual time synchronous time averaging (RTSA) is first employed to remove the operation-related IAS components that come from normal gear meshing and non-stationary load variations, KLPD is then utilized to detect and enhance the speed jitter from the IAS residual in a data-driven manner. The effectiveness of proposed method has been validated by both simulated data and experimental data. The results demonstrate that the proposed KLPD-RTSA could not only detect fault signatures but also identify defective components, thus providing a promising tool for the health monitoring of planetary gearbox.

HAT-P-32b AND HAT-P-33b: TWO HIGHLY INFLATED HOT JUPITERS TRANSITING HIGH-JITTER STARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hartman, J. D.; Bakos, G. A.; Torres, G.

2011-11-20

We report the discovery of two exoplanets transiting high-jitter stars. HAT-P-32b orbits the bright V = 11.289 late-F-early-G dwarf star GSC 3281-00800, with a period P = 2.150008 {+-} 0.000001 d. The stellar and planetary masses and radii depend on the eccentricity of the system, which is poorly constrained due to the high-velocity jitter ({approx}80 m s{sup -1}). Assuming a circular orbit, the star has a mass of 1.16 {+-} 0.04 M{sub Sun} and radius of 1.22 {+-} 0.02 R{sub Sun }, while the planet has a mass of 0.860 {+-} 0.164 M{sub J} and a radius of 1.789 {+-}more » 0.025 R{sub J}. The second planet, HAT-P-33b, orbits the bright V = 11.188 late-F dwarf star GSC 2461-00988, with a period P = 3.474474 {+-} 0.000001 d. As for HAT-P-32, the stellar and planetary masses and radii of HAT-P-33 depend on the eccentricity, which is poorly constrained due to the high jitter ({approx}50 m s{sup -1}). In this case, spectral line bisector spans (BSs) are significantly anti-correlated with the radial velocity residuals, and we are able to use this correlation to reduce the residual rms to {approx}35 m s{sup -1}. We find that the star has a mass of 1.38 {+-} 0.04 M{sub Sun} and a radius of 1.64 {+-} 0.03 R{sub Sun} while the planet has a mass of 0.762 {+-} 0.101 M{sub J} and a radius of 1.686 {+-} 0.045 R{sub J} for an assumed circular orbit. Due to the large BS variations exhibited by both stars we rely on detailed modeling of the photometric light curves to rule out blend scenarios. Both planets are among the largest radii transiting planets discovered to date.« less

A sexual health quality improvement program (SHIMMER) triples chlamydia and gonorrhoea testing rates among young people attending Aboriginal primary health care services in Australia.

PubMed

Graham, Simon; Guy, Rebecca J; Wand, Handan C; Kaldor, John M; Donovan, Basil; Knox, Janet; McCowen, Debbie; Bullen, Patricia; Booker, Julie; O'Brien, Chris; Garrett, Kristine; Ward, James S

2015-09-02

In Australia, chlamydia is the most commonly notifiable infection and over the past ten years chlamydia and gonorrhoea notification rates have increased. Aboriginal compared with non-Aboriginal Australians have the highest notifications rates of chlamydia and gonorrhoea. Regular testing of young people for chlamydia and gonorrhoea is a key prevention strategy to identify asymptomatic infections early, provide treatment and safe sex education. This study evaluated if a sexual health quality improvement program (QIP) known as SHIMMER could increase chlamydia and gonorrhoea testing among young people attending four Aboriginal primary health care services in regional areas of New South Wales, Australia. We calculated the proportion of 15-29 year olds tested and tested positivity for chlamydia and gonorrhoea in a 12-month before period (March 2010-February 2011) compared with a 12-month QIP period (March 2012-February 2013). Logistic regression was used to assess the difference in the proportion tested for chlamydia and gonorrhoea between study periods by gender, age group, Aboriginal status and Aboriginal primary health service. Odds ratios (OR) and their 95 % confidence intervals (CIs) were calculated with significance at p < 0.05. In the before period, 9 % of the 1881 individuals were tested for chlamydia, compared to 22 % of the 2259 individuals in the QIP period (OR): 1.43, 95 % CI: 1.22-1.67). From the before period to the QIP period, increases were observed in females (13 % to 25 %, OR: 1.32, 95 % CI: 1.10-1.59) and males (3 % to 17 %, OR: 1.85, 95 % CI: 1.36-2.52). The highest testing rate in the QIP period was in 15-19 year old females (16 % to 29 %, OR: 1.02, 95 % CI: 0.75-1.37), yet the greatest increase was in 20-24 year olds males (3 % to 19 %, OR: 1.65, 95 % CI: 1.01-2.69). Similar increases were seen in gonorrhoea testing. Overall, there were 70 (11 %) chlamydia diagnoses, increasing from 24 in the before to 46 in the QIP period. Overall, 4 (0

Improving carrier-envelope phase stability in optical parametric chirped-pulse amplifiers by control of timing jitter.

PubMed

Hädrich, S; Rothhardt, J; Krebs, M; Demmler, S; Limpert, J; Tünnermann, A

2012-12-01

It is shown that timing jitter in optical parametric chirped-pulse amplification induces spectral drifts that transfer to carrier-envelope phase (CEP) instabilities via dispersion. Reduction of this effect requires temporal synchronization, which is realized with feedback obtained from the angularly dispersed idler. Furthermore, a novel method to measure the CEP drifts by utilizing parasitic second harmonic generation within parametric amplifiers is presented. Stabilization of the timing allows the obtainment of a CEP stability of 86 mrad over 40 min at 150 kHz repetition rate.

Acoustic changes in the speech of children with cerebral palsy following an intensive program of dysarthria therapy.

PubMed

Pennington, Lindsay; Lombardo, Eftychia; Steen, Nick; Miller, Nick

2018-01-01

The speech intelligibility of children with dysarthria and cerebral palsy has been observed to increase following therapy focusing on respiration and phonation. To determine if speech intelligibility change following intervention is associated with change in acoustic measures of voice. We recorded 16 young people with cerebral palsy and dysarthria (nine girls; mean age 14 years, SD = 2; nine spastic type, two dyskinetic, four mixed; one Worster-Drought) producing speech in two conditions (single words, connected speech) twice before and twice after therapy focusing on respiration, phonation and rate. In both single-word and connected speech we measured vocal intensity (root mean square-RMS), period-to-period variability (Shimmer APQ, Jitter RAP and PPQ) and harmonics-to-noise ratio (HNR). In connected speech we also measured mean fundamental frequency, utterance duration in seconds and speech and articulation rate (syllables/s with and without pauses respectively). All acoustic measures were made using Praat. Intelligibility was calculated in previous research. In single words statistically significant but very small reductions were observed in period-to-period variability following therapy: Shimmer APQ -0.15 (95% CI = -0.21 to -0.09); Jitter RAP -0.08 (95% CI = -0.14 to -0.01); Jitter PPQ -0.08 (95% CI = -0.15 to -0.01). No changes in period-to-period perturbation across phrases in connected speech were detected. However, changes in connected speech were observed in phrase length, rate and intensity. Following therapy, mean utterance duration increased by 1.11 s (95% CI = 0.37-1.86) when measured with pauses and by 1.13 s (95% CI = 0.40-1.85) when measured without pauses. Articulation rate increased by 0.07 syllables/s (95% CI = 0.02-0.13); speech rate increased by 0.06 syllables/s (95% CI = < 0.01-0.12); and intensity increased by 0.03 Pascals (95% CI = 0.02-0.04). There was a gradual reduction in mean fundamental frequency across all time points (-11.85 Hz, 95

Voice stress analysis

NASA Technical Reports Server (NTRS)

Brenner, Malcolm; Shipp, Thomas

1988-01-01

In a study of the validity of eight candidate voice measures (fundamental frequency, amplitude, speech rate, frequency jitter, amplitude shimmer, Psychological Stress Evaluator scores, energy distribution, and the derived measure of the above measures) for determining psychological stress, 17 males age 21 to 35 were subjected to a tracking task on a microcomputer CRT while parameters of vocal production as well as heart rate were measured. Findings confirm those of earlier studies that increases in fundamental frequency, amplitude, and speech rate are found in speakers involved in extreme levels of stress. In addition, it was found that the same changes appear to occur in a regular fashion within a more subtle level of stress that may be characteristic, for example, of routine flying situations. None of the individual speech measures performed as robustly as did heart rate.

The identification of credit card encoders by hierarchical cluster analysis of the jitters of magnetic stripes.

PubMed

Leung, S C; Fung, W K; Wong, K H

1999-01-01

The relative bit density variation graphs of 207 specimen credit cards processed by 12 encoding machines were examined first visually, and then classified by means of hierarchical cluster analysis. Twenty-nine credit cards being treated as 'questioned' samples were tested by way of cluster analysis against 'controls' derived from known encoders. It was found that hierarchical cluster analysis provided a high accuracy of identification with all 29 'questioned' samples classified correctly. On the other hand, although visual comparison of jitter graphs was less discriminating, it was nevertheless capable of giving a reasonably accurate result.

Acoustic and perceptual aspects of vocal function in children with adenotonsillar hypertrophy--effects of surgery.

PubMed

Lundeborg, Inger; Hultcrantz, Elisabeth; Ericsson, Elisabeth; McAllister, Anita

2012-07-01

To evaluate outcome of two types of tonsil surgery (tonsillectomy [TE]+adenoidectomy or tonsillotomy [TT]+adenoidectomy) on vocal function perceptually and acoustically. Sixty-seven children, aged 50-65 months, on waiting list for tonsil surgery were randomized to TE (n=33) or TT (n=34). Fifty-seven age- and gender-matched healthy preschool children were controls. Twenty-eight of them, aged 48-59 months, served as control group before surgery, and 29, aged 60-71 months, served as control group after surgery. Before surgery and 6 months postoperatively, the children were recorded producing three sustained vowels (/ɑ/, /u/, and /i/) and 14 words. The control groups were recorded only once. Three trained speech and language pathologists performed the perceptual analysis using visual analog scale for eight voice quality parameters. Acoustic analysis from sustained vowels included average fundamental frequency, jitter percent, shimmer percent, noise-to-harmonic ratio, and the center frequencies of formants 1-3. Before surgery, the children were rated to have more hyponasality and compressed/throaty voice (P<0.05) and lower mean pitch (P<0.01) in comparison to the control group. They also had higher perturbation measures and lower frequencies of the second and third formants. After surgery, there were no differences perceptually. Perturbation measures decreased but were still higher compared with those of control group (P<0.05). Differences in formant frequencies for /i/ and /u/ remained. No differences were found between the two surgical methods. Voice quality is affected perceptually and acoustically by adenotonsillar hypertrophy. After surgery, the voice is perceptually normalized but acoustic differences remain. Outcome was equal for both surgical methods. Copyright © 2012 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Cardiovascular effects of intraosseous injections of 2 percent lidocaine with 1:100,000 epinephrine and 3 percent mepivacaine.

PubMed

Replogle, K; Reader, A; Nist, R; Beck, M; Weaver, J; Meyers, W J

1999-05-01

Because a number of patients have reported an increase in heart rate with the intraosseous, or i.o., injection, it is important to evaluate changes in the cardiovascular system with this injection technique. The purpose of this study was to determine the cardiovascular effects of an i.o. injection of 2 percent lidocaine with 1:100,000 epinephrine and 3 percent mepivacaine. With the use of a repeated-measures design, the authors randomly assigned 42 subjects to receive i.o. injections of 1.8 milliliters of 2 percent lidocaine with 1:100,000 epinephrine or 1.8 mL of 3 percent mepivacaine in a double-blinded manner at two appointments. At each appointment the authors monitored electrocardiographic findings, cardiac rate, systolic and diastolic blood pressure, and mean arterial pressure before, during and after administration of anesthetic solutions. With the 2 percent lidocaine with 1:100,000 epinephrine solution, 28 (67 percent) of 42 subjects experienced an increase in heart rate that might be attributed to the effect of the epinephrine. In 22 (79 percent) of these subjects, the heart rate returned to within 5 beats of baseline values within four minutes after solution deposition. The authors found no significant increase in heart rate in subjects receiving the 3 percent mepivacaine. No significant differences (P > .05) were found in mean diastolic, mean systolic or mean arterial blood pressure values between the subjects receiving 2 percent lidocaine with 1:100,000 epinephrine and those receiving 3 percent mepivacaine. The majority of subjects receiving the i.o. injection of the 2 percent lidocaine-epinephrine solution experienced a transient increase in heart rate. No significant increase in heart rate was seen with the i.o. injection of 3 percent mepivacaine. While patients would likely notice the heart rate increase with the lidocaine-epinephrine solution, it would not be clinically significant in most healthy patients. In patients whose medical condition, drug

Comparing the Exposure-Response Relationships of Physiological and Traditional Vocal Warm-ups on Aerodynamic and Acoustic Parameters in Untrained Singers.

PubMed

Kang, Jing; Xue, Chao; Chou, Adriana; Scholp, Austin; Gong, Ting; Zhang, Yi; Chen, Zhen; Jiang, Jack J

2018-02-05

The aim of this study was to quantify the effects of traditional and physiological warm-up exercises and to determine the optimal duration of these methods using acoustic and aerodynamic metrics. Twenty-six subjects were recruited to participate in both straw phonation exercises (physiological vocal warm-up) and traditional singing exercises (traditional vocal warm-up) for 20 minutes each, 24 hours apart. Phonation threshold pressure (PTP), fundamental frequency, jitter, shimmer, and noise-to-harmonics ratio were measured before the intervention (m0), as well as after 5 minutes (m5), 10 minutes (m10), 15 minutes (m15), and 20 minutes (m20) of intervention. PTP decreased significantly after straw phonation and reached a minimum value at 10 minutes (P < 0.001) and remained stable in traditional singing exercises. There were significant differences in fundamental frequency and shimmer from m0 to m15 and m20 in the traditional singing group (P = 0.001, P = 0.001, P = 0.001, and P = 0.002, respectively). No significant changes in acoustic parameters were observed after straw phonation. Both straw phonation exercises and traditional singing exercises are effective for voice warm-up. Straw phonation improves the subjects' fatigue resistance and vocal economy, resulting in a reduced PTP, whereas traditional singing exercises focus on technical singing skills, leading to an improvement of acoustic variables. Copyright © 2018 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Asymmetric dual-loop feedback to suppress spurious tones and reduce timing jitter in self-mode-locked quantum-dash lasers emitting at 155 μm

NASA Astrophysics Data System (ADS)

Asghar, Haroon; McInerney, John G.

2017-09-01

We demonstrate an asymmetric dual-loop feedback scheme to suppress external cavity side-modes induced in self-mode-locked quantum-dash lasers with conventional single and dual-loop feedback. In this letter, we achieved optimal suppression of spurious tones by optimizing the length of second delay time. We observed that asymmetric dual-loop feedback, with large (~8x) disparity in cavity lengths, eliminates all external-cavity side-modes and produces flat RF spectra close to the main peak with low timing jitter compared to single-loop feedback. Significant reduction in RF linewidth and reduced timing jitter was also observed as a function of increased second feedback delay time. The experimental results based on this feedback configuration validate predictions of recently published numerical simulations. This interesting asymmetric dual-loop feedback scheme provides simplest, efficient and cost effective stabilization of side-band free optoelectronic oscillators based on mode-locked lasers.

38 CFR 4.31 - Zero percent evaluations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2010-07-01 2010-07-01 false Zero percent evaluations... FOR RATING DISABILITIES General Policy in Rating § 4.31 Zero percent evaluations. In every instance where the schedule does not provide a zero percent evaluation for a diagnostic code, a zero percent...

38 CFR 4.31 - Zero percent evaluations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2014-07-01 2014-07-01 false Zero percent evaluations... FOR RATING DISABILITIES General Policy in Rating § 4.31 Zero percent evaluations. In every instance where the schedule does not provide a zero percent evaluation for a diagnostic code, a zero percent...

38 CFR 4.31 - Zero percent evaluations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2012-07-01 2012-07-01 false Zero percent evaluations... FOR RATING DISABILITIES General Policy in Rating § 4.31 Zero percent evaluations. In every instance where the schedule does not provide a zero percent evaluation for a diagnostic code, a zero percent...

38 CFR 4.31 - Zero percent evaluations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2013-07-01 2013-07-01 false Zero percent evaluations... FOR RATING DISABILITIES General Policy in Rating § 4.31 Zero percent evaluations. In every instance where the schedule does not provide a zero percent evaluation for a diagnostic code, a zero percent...

38 CFR 4.31 - Zero percent evaluations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 1 2011-07-01 2011-07-01 false Zero percent evaluations... FOR RATING DISABILITIES General Policy in Rating § 4.31 Zero percent evaluations. In every instance where the schedule does not provide a zero percent evaluation for a diagnostic code, a zero percent...

Inspiration: One Percent and Rising

ERIC Educational Resources Information Center

Walling, Donovan R.

2009-01-01

Inventor Thomas Edison once famously declared, "Genius is one percent inspiration and ninety-nine percent perspiration." If that's the case, then the students the author witnessed at the International Student Media Festival (ISMF) last November in Orlando, Florida, are geniuses and more. The students in the ISMF pre-conference workshop…

The role of auditory and kinaesthetic feedback mechanisms on phonatory stability in children.

PubMed

Rathna Kumar, S B; Azeem, Suhail; Choudhary, Abhishek Kumar; Prakash, S G R

2013-12-01

Auditory feedback plays an important role in phonatory control. When auditory feedback is disrupted, various changes are observed in vocal motor control. Vocal intensity and fundamental frequency (F0) levels tend to increase in response to auditory masking. Because of the close reflexive links between the auditory and phonatory systems, it is likely that phonatory stability may be disrupted when auditory feedback is disrupted or altered. However, studies on phonatory stability under auditory masking condition in adult subjects showed that most of the subjects maintained normal levels of phonatory stability. The authors in the earlier investigations suggested that auditory feedback is not the sole contributor to vocal motor control and phonatory stability, a complex neuromuscular reflex system known as kinaesthetic feedback may play a role in controlling phonatory stability when auditory feedback is disrupted or lacking. This proposes the need to further investigate this phenomenon as to whether children show similar patterns of phonatory stability under auditory masking since their neuromotor systems are still at developmental stage, less mature and are less resistant to altered auditory feedback than adults. A total of 40 normal hearing and speaking children (20 male and 20 female) between the age group of 6 and 8 years participated as subjects. The acoustic parameters such as shimmer, jitter and harmonic-to-noise ratio (HNR) were measures and compared between no masking condition (0 dB ML) and masking condition (90 dB ML). Despite the neuromotor systems being less mature in children and less resistant than adults to altered auditory feedback, most of the children in the study demonstrated increased phonatory stability which was reflected by reduced shimmer, jitter and increased HNR values. This study implicates that most of the children demonstrate well established patterns of kinaesthetic feedback, which might have allowed them to maintain normal levels of

Problems in Microgravity Fluid Mechanics: G-Jitter Convection

NASA Technical Reports Server (NTRS)

Homsy, G. M.

2005-01-01

This is the final report on our NASA grant, Problems in Microgravity Fluid Mechanics NAG3-2513: 12/14/2000 - 11/30/2003, extended through 11/30/2004. This grant was made to Stanford University and then transferred to the University of California at Santa Barbara when the PI relocated there in January 2001. Our main activity has been to conduct both experimental and theoretical studies of instabilities in fluids that are relevant to the microgravity environment, i.e. those that do not involve the action of buoyancy due to a steady gravitational field. Full details of the work accomplished under this grant are given below. Our work has focused on: (i) Theoretical and computational studies of the effect of g-jitter on instabilities of convective states where the convection is driven by forces other than buoyancy (ii) Experimental studies of instabilities during displacements of miscible fluid pairs in tubes, with a focus on the degree to which these mimic those found in immiscible fluids. (iii) Theoretical and experimental studies of the effect of time dependent electrohydrodynamic forces on chaotic advection in drops immersed in a second dielectric liquid. Our objectives are to acquire insight and understanding into microgravity fluid mechanics problems that bear on either fundamental issues or applications in fluid physics. We are interested in the response of fluids to either a fluctuating acceleration environment or to forces other than gravity that cause fluid mixing and convection. We have been active in several general areas.

Percents Are Not Natural Numbers

ERIC Educational Resources Information Center

Jacobs, Jennifer A.

2013-01-01

Adults are prone to treating percents, one representational format of rational numbers, as novel cases of natural number. This suggests that percent values are not differentiated from natural numbers; a conceptual shift from the natural numbers to the rational numbers has not yet occurred. This is most surprising, considering people are inundated…

Acoustic voice analysis of prelingually deaf adults before and after cochlear implantation.

PubMed

Evans, Maegan K; Deliyski, Dimitar D

2007-11-01

It is widely accepted that many severe to profoundly deaf adults have benefited from cochlear implants (CIs). However, limited research has been conducted to investigate changes in voice and speech of prelingually deaf adults who receive CIs, a population well known for presenting with a variety of voice and speech abnormalities. The purpose of this study was to use acoustic analysis to explore changes in voice and speech for three prelingually deaf males pre- and postimplantation over 6 months. The following measurements, some measured in varying contexts, were obtained: fundamental frequency (F0), jitter, shimmer, noise-to-harmonic ratio, voice turbulence index, soft phonation index, amplitude- and F0-variation, F0-range, speech rate, nasalance, and vowel production. Characteristics of vowel production were measured by determining the first formant (F1) and second formant (F2) of vowels in various contexts, magnitude of F2-variation, and rate of F2-variation. Perceptual measurements of pitch, pitch variability, loudness variability, speech rate, and intonation were obtained for comparison. Results are reported using descriptive statistics. The results showed patterns of change for some of the parameters while there was considerable variation across the subjects. All participants demonstrated a decrease in F0 in at least one context and demonstrated a change in nasalance toward the norm as compared to their normal hearing control. The two participants who were oral-language communicators were judged to produce vowels with an average of 97.2% accuracy and the sign-language user demonstrated low percent accuracy for vowel production.

Effects of vibration (G-jitters) on convection in micro-gravity

NASA Technical Reports Server (NTRS)

Wang, Francis C.

1994-01-01

To obtain high quality crystals, it is desirable to maintain a diffusion-limited transport process in a planar solidification surface between the solid and the melt during the crystal growth process. Due to the presence of buoyancy-driven convection, however, this situation is difficult to maintain on Earth. The microgravity environment of an orbiting space laboratory presents an alternative worth pursuing. With reduced gravity, convections very much suppressed in a space laboratory, making the environment more conducive for growing crystals with better quality. However, a space laboratory is not immune from any undesirable disturbances. Nonuniform and transient accelerations such as vibrations, g-jitters, and impulsive accelerations exist as a result of crew activities, space maneuvering, and the operations of on-board equipment. Measurements conducted on-board a U.S. Spacelab mission showed the existence of vibrations in the frequency range of 1 to 100 Hz. It was reported that a dominant mode of 17 Hz and harmonics of 54 Hz were observed and these were attributed to antenna operations. The vibration is not limited to any single plane but exists in all directions. Some data from the Russian MIR space station indicates the existence of vibration also at this frequency range.

Beyond Marbles: Percent Change and Social Justice

ERIC Educational Resources Information Center

Denny, Flannery

2013-01-01

In the author's eighth year of teaching, she hit a wall teaching percent change. Percent change is one of the few calculations taught in math classes that shows up regularly in the media, and one that she often does in her head to make sense of the world around her. Despite this, she had been teaching percent change using textbook problems about…

Vascular lesions of the vocal fold.

PubMed

Gökcan, Kürşat Mustafa; Dursun, Gürsel

2009-04-01

The aim of the study was to present symptoms, laryngological findings, clinical course, management modalities, and consequences of vascular lesions of vocal fold. This study examined 162 patients, the majority professional voice users, with vascular lesions regarding their presenting symptoms, laryngological findings, clinical courses and treatment results. The most common complaint was sudden hoarseness with hemorrhagic polyp. Microlaryngoscopic surgery was performed in 108 cases and the main indication of surgery was the presence of vocal fold mass or development of vocal polyp during clinical course. Cold microsurgery was utilized for removal of vocal fold masses and feeding vessels cauterized using low power, pulsed CO(2) laser. Acoustic analysis of patients revealed a significant improvement of jitter, shimmer and harmonics/noise ratio values after treatment. Depending on our clinical findings, we propose treatment algorithm where voice rest and behavioral therapy is the integral part and indications of surgery are individualized for each patient.

Microphone and electroglottographic data from dysphonic patients: type 1, 2 and 3 signals.

PubMed

Behrman, A; Agresti, C J; Blumstein, E; Lee, N

1998-06-01

Recently, it has been suggested that statistics which are dependent upon the reliable extraction of a single fundamental period, such as jitter and shimmer, are valid only for nearly periodic signals. This study explored the incidence of nearly periodic and nonperiodic microphone and electroglottographic signals obtained from 202 dysphonic patients. It was found that approximately 42% were type 1 (nearly periodic); approximately 35% were type 2 (containing bifurcations, modulations or subharmonic structure); and approximately 22% were type 3 (chaotic). Discriminating between type 2 and 3 signals was very difficult for 40% of the signals which were ultimately rated type 3. This was due to the brevity of the apparently chaotic segment, and/or the persistence of some harmonic structure within the chaos. Irrespective of that difficulty, the results suggest that there may be a substantial incidence of nontype 1 signals in a given clinical population. It was concluded, therefore, that signal typing is a necessary step in the analyses of microphone and electoglottographic data.

An evaluation of 10 percent and 20 percent benzocaine gels in patients with acute toothaches: efficacy, tolerability and compliance with label dose administration directions.

PubMed

Hersh, Elliot V; Ciancio, Sebastian G; Kuperstein, Arthur S; Stoopler, Eric T; Moore, Paul A; Boynes, Sean G; Levine, Steven C; Casamassimo, Paul; Leyva, Rina; Mathew, Tanya; Shibly, Othman; Creighton, Paul; Jeffers, Gary E; Corby, Patricia M A; Turetzky, Stanley N; Papas, Athena; Wallen, Jillian; Idzik-Starr, Cynthia; Gordon, Sharon M

2013-05-01

The authors evaluated the efficacy and tolerability of 10 percent and 20 percent benzocaine gels compared with those of a vehicle (placebo) gel for the temporary relief of toothache pain. They also assessed the compliance with the label dose administration directions on the part of participants with toothache pain. Under double-masked conditions, 576 participants self-applied study gel to an open tooth cavity and surrounding oral tissues. Participants evaluated their pain intensity and pain relief for 120 minutes. The authors determined the amount of gel the participants applied. The responders' rates (the primary efficacy parameter), defined as the percentage of participants who had an improvement in pain intensity as exhibited by a pain score reduction of at least one unit on the dental pain scale from baseline for two consecutive assessments any time between the five- and 20-minute points, were 87.3 percent, 80.7 percent and 70.4 percent, respectively, for 20 percent benzocaine gel, 10 percent benzocaine gel and vehicle gel. Both benzocaine gels were significantly (P ≤ .05) better than vehicle gel; the 20 percent benzocaine gel also was significantly (P ≤ .05) better than the 10 percent benzocaine gel. The mean amount of gel applied was 235.6 milligrams, with 88.2 percent of participants applying 400 mg or less. Both 10 percent and 20 percent benzocaine gels were more efficacious than the vehicle gel, and the 20 percent benzocaine gel was more efficacious than the 10 percent benzocaine gel. All treatments were well tolerated by participants. Practical Implications. Patients can use 10 percent and 20 percent benzocaine gels to temporarily treat toothache pain safely.

Managing piezoelectric sensor jitter: kinematic position tracking applications

NASA Astrophysics Data System (ADS)

Khomo, Malome T.

2016-02-01

Piezo-acoustic distance tracking sensors have challenges of reporting true distance readings. Challenges include directional anisotropy signal loss in transmission power and in receiver sensitivity, distance-related attenuation of signal and the phase shifts that result in jittery values, some preceding, and others succeeding the expected distance readings. There also exist signal time losses arising from dead time associated with processor latency, with carrier signal pulse length and with voltage rise-time delays in pulse detection. Together these factors cause distance under-reporting, and more critically, makes each reported value uncertain, which is unacceptable in distance-critical applications. Piezo-inertial accelerometers have equivalent if not more severe challenges in tri-axial configurations, for instance where a rotational tilt may happen under linear accelerative force. In the absence of tensor component adaptation to change of orientation, signal is lost until the next axial sensor detects it. Study paper focusses on piezo-acoustic transducers UCD1007 and 400SR160 (40kHz), used in a face-to-face configuration over a 600mm range. Within that range 10 successive phase shift wave fronts were identified, but it took 15 reconstructed wave fronts to uniquely identify a continuous end-to-end jitter-free and slippage-free kinematic data stream from the jittery sensor data. The additional 5 degrees of freedom were consumed by the 5-stage filter applied. The technique has remarkable combinatorial and projective geometry implications for digital sensor design. It is possible for the procedure to be applicable in 3-axis accelerometers and adapted into firmware for truly kinematic device driver interfaces so long as the reporting rates are matched with the user interface refresh rates. It is shown that acoustic transducer sensors require phase loop locking for kinematic continuity whereas gravimetric accelerometers demand better measurement time consistence in

A Conceptual Model for Solving Percent Problems.

ERIC Educational Resources Information Center

Bennett, Albert B., Jr.; Nelson, L. Ted

1994-01-01

Presents an alternative method to teaching percent problems which uses a 10x10 grid to help students visualize percents. Offers a means of representing information and suggests different approaches for finding solutions. Includes reproducible student worksheet. (MKR)

Method and apparatus for reducing spacecraft instrument induced jitter via multifrequency cancellation

NASA Technical Reports Server (NTRS)

Liu, Ketao (Inventor); Uetrecht, David S. (Inventor)

2002-01-01

A method, apparatus, article of manufacture, and a memory structure for compensating for instrument induced spacecraft jitter is disclosed. The apparatus comprises a spacecraft control processor for producing an actuator command signal, a signal generator, for producing a cancellation signal having at least one harmonic having a frequency and an amplitude substantially equal to that of a disturbance harmonic interacting with a spacecraft structural resonance and a phase substantially out of phase with the disturbance harmonic interacting with the spacecraft structural resonance, and at least one spacecraft control actuator, communicatively coupled to the spacecraft control processor and the signal generator for inducing satellite motion according to the actuator command signal and the cancellation signal. The method comprises the steps of generating a cancellation signal having at least one harmonic having a frequency and an amplitude substantially equal to that of a disturbance harmonic interacting with a spacecraft structural resonance and a phase substantially out of phase with the disturbance harmonic interacting with the spacecraft structural resonance, and providing the cancellation signal to a spacecraft control actuator. The apparatus comprises a storage device tangibly embodying the method steps described above.

Guidance on Compatibility of UST Systems with Ethanol Blends Greater Than 10 Percent and Biodiesel Blends Greater Than 20 Percent

EPA Pesticide Factsheets

EPA guidance on complying with the federal compatibility requirement for underground storage tank (UST) systems storing gasoline containing greater than 10 percent ethanol or diesel containing greater than 20 percent biodiesel.

Simulation of sloshing dynamics induced forces and torques actuated on dewar container driven by gravity gradient and jitter accelerations in microgravity

NASA Technical Reports Server (NTRS)

Hung, R. J.; Pan, H. L.

1993-01-01

Some experimental spacecraft use superconducting sensors for gyro read-out and so must be maintained at a very low temperature. The boil-off from the cryogenic liquid used to cool the sensors can also be used, as the Gravity Probe B (GP-B) spacecraft does, as propellant to maintain attitude control and drag-free operation of the spacecraft. The cryogenic liquid for such spacecraft is, however, susceptible to both slosh-like motion and non-axisymmetric configurations under the influence of various kinds of gravity jitter and gravity gradient accelerations. Hence, it is important to quantify the magnitude of the liquid-induced perturbations on the spacecraft. We use the example of the GP-B to investigate such perturbations by numerical simulations. For this spacecraft disturbances can be imposed on the liquid by atmospheric drag, spacecraft attitude control maneuvers, and the earth's gravity gradient. More generally, onboard machinery vibrations and crew motion can also create disturbances. Recent studies suggest that high frequency disturbances are relatively unimportant in causing liquid motions in comparison to low frequency ones. The results presented here confirm this conclusion. After an initial calibration period, the GP-B spacecraft rotates in orbit at 0.1 rpm about the tank symmetry axis. For this rotation rate, the equilibrium liquid free surface shape is a 'doughnut' configuration for all residual gravity levels of 10(exp -6) g(sub 0) or less, as shown by experiments and by numerical simulations; furthermore, the superfluid behavior of the 1.8 K liquid helium used in GP-B eliminates temperature gradients and therefore such effects as Marangoni convection do not have to be considered. Classical fluid dynamics theory is used as the basis of the numerical simulations here, since Mason's experiments show that the theory is applicable for cryogenic liquid helium in large containers. To study liquid responses to various disturbances, we investigate and simulate

Voice Quality After a Semi-Occluded Vocal Tract Exercise With a Ventilation Mask in Contemporary Commercial Singers: Acoustic Analysis and Self-Assessments.

PubMed

Fantini, Marco; Succo, Giovanni; Crosetti, Erika; Borragán Torre, Alfonso; Demo, Roberto; Fussi, Franco

2017-05-01

The current study aimed at investigating the immediate effects of a semi-occluded vocal tract exercise with a ventilation mask in a group of contemporary commercial singers. A randomized controlled study was carried out. Thirty professional or semi-professional singers with no voice complaints were randomly divided into two groups on recruitment: an experimental group and a control group. The same warm-up exercise was performed by the experimental group with an occluded ventilation mask placed over the nose and the mouth and by the control group without the ventilation mask. Voice was recorded before and after the exercise. Acoustic and self-assessment analysis were accomplished. The acoustic parameters of the voice samples recorded before and after training were compared, as well as the parameters' variations between the experimental and the control group. Self-assessment results of the experimental and the control group were compared too. Significant changes after the warm-up exercise included jitter, shimmer, and singing power ratio (SPR) in the experimental group. No significant changes were recorded in the control group. Significant differences between the experimental and the control group were found for ΔShimmer and ΔSPR. Self-assessment analysis confirmed a significantly higher phonatory comfort and voice quality perception for the experimental group. The results of the present study support the immediate advantageous effects on singing voice of a semi-occluded vocal tract exercise with a ventilation mask in terms of acoustic quality, phonatory comfort, and voice quality perception in contemporary commercial singers. Long-term effects still remain to be studied. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Full-custom design of split-set data weighted averaging with output register for jitter suppression

NASA Astrophysics Data System (ADS)

Jubay, M. C.; Gerasta, O. J.

2015-06-01

A full-custom design of an element selection algorithm, named as Split-set Data Weighted Averaging (SDWA) is implemented in 90nm CMOS Technology Synopsys Library. SDWA is applied in seven unit elements (3-bit) using a thermometer-coded input. Split-set DWA is an improved DWA algorithm which caters the requirement for randomization along with long-term equal element usage. Randomization and equal element-usage improve the spectral response of the unit elements due to higher Spurious-free dynamic range (SFDR) and without significantly degrading signal-to-noise ratio (SNR). Since a full-custom, the design is brought to transistor-level and the chip custom layout is also provided, having a total area of 0.3mm2, a power consumption of 0.566 mW, and simulated at 50MHz clock frequency. On this implementation, SDWA is successfully derived and improved by introducing a register at the output that suppresses the jitter introduced at the final stage due to switching loops and successive delays.

48 CFR 1852.219-76 - NASA 8 percent goal.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true NASA 8 percent goal. 1852... 1852.219-76 NASA 8 percent goal. As prescribed in 1819.7003 insert the following clause: NASA 8 Percent... and daily business operations are controlled by one or more women. (b) The NASA Administrator is...

48 CFR 1852.219-76 - NASA 8 percent goal.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 48 Federal Acquisition Regulations System 6 2013-10-01 2013-10-01 false NASA 8 percent goal. 1852... 1852.219-76 NASA 8 percent goal. As prescribed in 1819.7003 insert the following clause: NASA 8 Percent... and daily business operations are controlled by one or more women. (b) The NASA Administrator is...

48 CFR 1852.219-76 - NASA 8 percent goal.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 48 Federal Acquisition Regulations System 6 2014-10-01 2014-10-01 false NASA 8 percent goal. 1852... 1852.219-76 NASA 8 percent goal. As prescribed in 1819.7003 insert the following clause: NASA 8 Percent... and daily business operations are controlled by one or more women. (b) The NASA Administrator is...

48 CFR 1852.219-76 - NASA 8 percent goal.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 48 Federal Acquisition Regulations System 6 2012-10-01 2012-10-01 false NASA 8 percent goal. 1852... 1852.219-76 NASA 8 percent goal. As prescribed in 1819.7003 insert the following clause: NASA 8 Percent... and daily business operations are controlled by one or more women. (b) The NASA Administrator is...

48 CFR 1852.219-76 - NASA 8 percent goal.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false NASA 8 percent goal. 1852... 1852.219-76 NASA 8 percent goal. As prescribed in 1819.7003 insert the following clause: NASA 8 Percent... and daily business operations are controlled by one or more women. (b) The NASA Administrator is...

Distinct Disease and Functional Characteristics of Thyroid Surgery-Related Vocal Fold Palsy.

PubMed

Tseng, Wen-Chun; Pei, Yu-Cheng; Wong, Alice M K; Li, Hsueh-Yu; Fang, Tuan-Jen

2016-07-01

Iatrogenic trauma induced by thyroid surgery is the most common etiology of unilateral vocal fold paralysis (UVFP). UVFP after thyroid surgery may lead to profound physical and psychosocial distress. This study comprehensively evaluated UVFP caused by thyroid surgery, and compared the results with those caused by other surgical trauma. Patients with surgery-related UVFP were evaluated using quantitative laryngeal electromyography, videolaryngostroboscopy, voice acoustic analysis, the Voice Outcome Survey, and the Short Form-36 Health Survey quality-of-life questionnaire. Patients with thyroid surgery and other surgeries were compared. A total of 105 patients were recruited, of whom 52 and 53 were assigned to the thyroid surgery and the other surgery group, respectively. Patients in the thyroid surgery group had a higher proportion of external branch of superior laryngeal nerve (eSLN) involvement, longer duration from disease onset to the first laryngeal electromyography examination, lower jitter, higher harmonic-to-noise ratio, and better quality of life compared with the other surgery group. Specifically for patients in the thyroid surgery group, those with eSLN involvement tended to have more pronounced impairment in jitter and shimmer compared with patients without eSLN involvement. UVFP caused by thyroid surgery has a distinct clinical presentation with relatively high involvement in the eSLN, better voice acoustics, longer waiting time before asking for evaluation, and less impact on quality of life. The involvement of eSLN in these patients further impaired their voice. Early referral is suggested for these patients, especially with suspected eSLN injury.

Changes After Voice Therapy in Acoustic Voice Analysis of Chinese Patients With Voice Disorders.

PubMed

Lu, Dan; Chen, Fei; Yang, Hui; Yu, Rong; Zhou, Qi; Zhang, Xinyuan; Ren, Jia; Zheng, Yitao; Zhang, Xiaoyan; Zou, Jian; Wang, Haiyang; Liu, Jun

2018-05-01

This study aimed to evaluate the effects of voice therapy on patients with voice disorders by comparing the acoustic parameter changes before and after treatment. This is a retrospective study. Forty-five female patients with early-stage vocal nodules or polyps, postoperative patients, and patients with chronic laryngitis were divided into three subgroups. Videostroboscopic, acoustic analysis (fundamental frequency, jitter, shimmer, mean harmonics-to-noise ratio), and maximum phonation time (MPT) were measured before and after treatment. Fifty healthy female volunteers were the control group. After treatment, 24.4% of nodules or polyps had decreased in size, 11.1% of patients with chronic laryngitis and postoperative patients had reduced edema, and the mucosal wave of vocal folds had different degrees of recovery in postoperative patients. All acoustic analysis values and MPT in the patient group were statistically worse than in the control group, except for fundamental frequency before treatment (P > 0.05). After treatment, the acoustic analysis and MPT values were improved. However, the jitter, mean harmonics-to-noise ratio, and MPT values in the patient group were still worse after voice therapy than in the control group (P < 0.05). Most of acoustic analysis values can be useful as a complementary tool in diagnosis and assessment of voice disorders; however, it is not recommended to use a single parameter to assess voice quality. Voice therapy can improve voice quality in patients with voice disorders, but a period longer than 8 weeks is recommended for these patients. Copyright © 2018 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Investigation of Effectiveness of a Wing Equipped with a 50-percent-chord Sliding Flap, a 30-percent-chord Slotted Flap, and a 30-percent-chord Slat in Deflecting Propeller Slipstreams Downward for Vertical Take-off

NASA Technical Reports Server (NTRS)

Kuhn, Richard E

1957-01-01

Results are presented of an investigation of the effectiveness of a wing equipped with a 50-percent-chord sliding flap and a 30-percent-chord slotted flap in deflecting a propeller slipstream downward for vertical take-off. Tests were conducted at zero forward speed in a large room and included the effects of flap deflection, proximity to the ground, a leading-edge slat, and end plates. A turning angle of about 70 degrees and a resultant force of about 100 percent of the thrust were achieved near the ground. Out of the ground-effect region, the turning angle was also about 70 degrees but the resultant force was reduced to about 86 percent of the thrust.

26 CFR 301.6226(b)-1 - 5-percent group.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 26 Internal Revenue 18 2011-04-01 2011-04-01 false 5-percent group. 301.6226(b)-1 Section 301.6226... ADMINISTRATION PROCEDURE AND ADMINISTRATION Assessment In General § 301.6226(b)-1 5-percent group. (a) In general. All members of a 5-percent group shall join in filing any petition for judicial review. The...

26 CFR 301.6226(b)-1 - 5-percent group.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 26 Internal Revenue 18 2014-04-01 2014-04-01 false 5-percent group. 301.6226(b)-1 Section 301.6226... ADMINISTRATION PROCEDURE AND ADMINISTRATION Assessment In General § 301.6226(b)-1 5-percent group. (a) In general. All members of a 5-percent group shall join in filing any petition for judicial review. The...

26 CFR 301.6226(b)-1 - 5-percent group.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 26 Internal Revenue 18 2012-04-01 2012-04-01 false 5-percent group. 301.6226(b)-1 Section 301.6226... ADMINISTRATION PROCEDURE AND ADMINISTRATION Assessment In General § 301.6226(b)-1 5-percent group. (a) In general. All members of a 5-percent group shall join in filing any petition for judicial review. The...

26 CFR 301.6226(b)-1 - 5-percent group.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 18 2010-04-01 2010-04-01 false 5-percent group. 301.6226(b)-1 Section 301.6226... ADMINISTRATION PROCEDURE AND ADMINISTRATION Assessment In General § 301.6226(b)-1 5-percent group. (a) In general. All members of a 5-percent group shall join in filing any petition for judicial review. The...

Subjective and objective voice evaluation in Sjögren's syndrome.

PubMed

Saltürk, Ziya; Özdemir, Erdi; Kumral, Tolgar Lütfi; Karabacakoğlu, Zeynep; Kumral, Esra; Yildiz, Hatice Elvin; Mersinlioğlu, Gökhan; Atar, Yavuz; Berkiten, Güler; Yildirim, Güven; Uyar, Yavuz

2017-04-01

Objective The aim of this study is to assess the subjective and objective aspects of voice in Sjögren's syndrome. Methods The study enrolled 10 women with Sjögren's syndrome and 12 healthy women. Maximum phonation time, fundamental frequency, jitter, shimmer, and noise-to-harmonics ratio were determined during acoustic voice analysis. The Stroboscopy Evaluation Rating Form was used for the laryngostroboscopic evaluation. A subjective evaluation was performed using the Turkish version of Voice Handicap Index-10. Results The mean age of the Sjögren's syndrome and control groups was 46 ± 13.89 and 41.27 ± 6.99 years, respectively, and did not differ (P = 0.131). In the laryngostroboscopic evaluation, the smoothness and straightness of vocal folds, regularity, and glottal closure differed significantly. In the acoustic and aerodynamic analyses, none of the parameters differed statistically, while the Sjögren's syndrome group had significantly higher Voice Handicap Index-10 scores than the controls. Conclusion Sjögren's syndrome affects the voice and voice quality.

Changes after voice therapy in objective and subjective voice measurements of pediatric patients with vocal nodules.

PubMed

Tezcaner, Ciler Zahide; Karatayli Ozgursoy, Selmin; Ozgursoy, Selmin Karatayli; Sati, Isil; Dursun, Gursel

2009-12-01

The aim of this study was to analyze the efficiency of the voice therapy in children with vocal nodules by using the acoustic analysis and subjective assessment. Thirty-nine patients with vocal fold nodules, aged between 7 and 14, were included in the study. Each subject had voice therapy led by an experienced voice therapist once a week. All diagnostic and follow-up workouts were performed before the voice therapy and after the third or the sixth month. Transoral and/or transnasal videostroboscopic examination and acoustic analysis were achieved using multi-dimensional voice program (MDVP) and subjective analysis with GRBAS scale. As for the perceptual assessment, the difference was significant for four parameters out of five. A significant improvement was found in the acoustic analysis parameters of jitter, shimmer, and noise-to-harmonic ratio. The voice therapy which was planned according to patients' needs, age, compliance and response to therapy had positive effects on pediatric patients with vocal nodules. Acoustic analysis and GRBAS may be used successfully in the follow-up of pediatric vocal nodule treatment.

Effects of thermomechanical processing on tensile and long-time creep behavior of Nb-1 percent Zr-0.1 percent C sheet

NASA Technical Reports Server (NTRS)

Titran, Robert H.; Uz, Mehmet

1994-01-01

Effects of thermomechanical processing on the mechanical properties of Nb-1 wt. percent Zr-0.1 wt. percent C, a candidate alloy for use in advanced space power systems, were investigated. Sheet bars were cold rolled into 1-mm thick sheets following single, double, or triple extrusion operations at 1900 K. All the creep and tensile specimens were given a two-step heat treatment 1 hr at 1755 K + 2 hr 1475 K prior to testing. Tensile properties were determined at 300 as well as at 1350 K. Microhardness measurements were made on cold rolled, heat treated, and crept samples. Creep tests were carried out at 1350 K and 34.5 MPa for times of about 10,000 to 19,000 hr. The results show that the number of extrusions had some effects on both the microhardness and tensile properties. However, the long-time creep behavior of the samples were comparable, and all were found to have adequate properties to meet the design requirements of advanced power systems regardless of thermomechanical history. The results are discussed in correlation with processing and microstructure, and further compared to the results obtained from the testing of Nb-1 wt. percent Zr and Nb-1 wt. percent Zr-0.06 wt. percent C alloys.

Exploring the feasibility of smart phone microphone for measurement of acoustic voice parameters and voice pathology screening.

PubMed

Uloza, Virgilijus; Padervinskis, Evaldas; Vegiene, Aurelija; Pribuisiene, Ruta; Saferis, Viktoras; Vaiciukynas, Evaldas; Gelzinis, Adas; Verikas, Antanas

2015-11-01

The objective of this study is to evaluate the reliability of acoustic voice parameters obtained using smart phone (SP) microphones and investigate the utility of use of SP voice recordings for voice screening. Voice samples of sustained vowel/a/obtained from 118 subjects (34 normal and 84 pathological voices) were recorded simultaneously through two microphones: oral AKG Perception 220 microphone and SP Samsung Galaxy Note3 microphone. Acoustic voice signal data were measured for fundamental frequency, jitter and shimmer, normalized noise energy (NNE), signal to noise ratio and harmonic to noise ratio using Dr. Speech software. Discriminant analysis-based Correct Classification Rate (CCR) and Random Forest Classifier (RFC) based Equal Error Rate (EER) were used to evaluate the feasibility of acoustic voice parameters classifying normal and pathological voice classes. Lithuanian version of Glottal Function Index (LT_GFI) questionnaire was utilized for self-assessment of the severity of voice disorder. The correlations of acoustic voice parameters obtained with two types of microphones were statistically significant and strong (r = 0.73-1.0) for the entire measurements. When classifying into normal/pathological voice classes, the Oral-NNE revealed the CCR of 73.7% and the pair of SP-NNE and SP-shimmer parameters revealed CCR of 79.5%. However, fusion of the results obtained from SP voice recordings and GFI data provided the CCR of 84.60% and RFC revealed the EER of 7.9%, respectively. In conclusion, measurements of acoustic voice parameters using SP microphone were shown to be reliable in clinical settings demonstrating high CCR and low EER when distinguishing normal and pathological voice classes, and validated the suitability of the SP microphone signal for the task of automatic voice analysis and screening.

Probabilistic model of nonlinear penalties due to collision-induced timing jitter for calculation of the bit error ratio in wavelength-division-multiplexed return-to-zero systems

NASA Astrophysics Data System (ADS)

Sinkin, Oleg V.; Grigoryan, Vladimir S.; Menyuk, Curtis R.

2006-12-01

We introduce a fully deterministic, computationally efficient method for characterizing the effect of nonlinearity in optical fiber transmission systems that utilize wavelength-division multiplexing and return-to-zero modulation. The method accurately accounts for bit-pattern-dependent nonlinear distortion due to collision-induced timing jitter and for amplifier noise. We apply this method to calculate the error probability as a function of channel spacing in a prototypical multichannel return-to-zero undersea system.

Reduction of timing jitter in a Q-Switched Nd:YAG laser by direct bleaching of a Cr4+:YAG saturable absorber.

PubMed

Cole, Brian; Goldberg, Lew; Trussell, C Ward; Hays, Alan; Schilling, Bradley W; McIntosh, Chris

2009-02-02

A method for optical triggering of a Q-switched Nd:YAG laser by direct bleaching of a Cr:YAG saturable absorber is described. This method involves the bleaching of a thin sheet of the saturable absorber from a direction orthogonal to the lasing axis using a single laser diode bar, where the Cr:YAG transmission increased from a non-bleached value of 47% to a bleached value of 63%. For steady state operation of a passively Q-switched laser (PRF=10 Hz), the pulse-to-pulse timing jitter showed approximately 12X reduction in standard deviation, from 241 nsec for free running operation to 20 nsec with optical triggering.

Transmission line transformer for reliable and low-jitter triggering of a railgap switch.

PubMed

Verma, Rishi; Mishra, Ekansh; Sagar, Karuna; Meena, Manraj; Shyam, Anurag

2014-09-01

The performance of railgap switch critically relies upon multichannel breakdown between the extended electrodes (rails) in order to ensure distributed current transfer along electrode length and to minimize the switch inductance. The initiation of several simultaneous arc channels along the switch length depends on the gap triggering technique and on the rate at which the electric field changes within the gap. This paper presents design, construction, and output characteristics of a coaxial cable based three-stage transmission line transformer (TLT) that is capable of initiating multichannel breakdown in a high voltage, low inductance railgap switch. In each stage three identical lengths of URM67 coaxial cables have been used in parallel and they have been wounded in separate cassettes to enhance the isolation of the output of transformer from the input. The cascaded output impedance of TLT is ~50 Ω. Along with multi-channel formation over the complete length of electrode rails, significant reduction in jitter (≤2 ns) and conduction delay (≤60 ns) has been observed by the realization of large amplitude (~80 kV), high dV/dt (~6 kV/ns) pulse produced by the indigenously developed TLT based trigger generator. The superior performance of TLT over conventional pulse transformer for railgap triggering application has been compared and demonstrated experimentally.

Giant honeybees ( Apis dorsata) mob wasps away from the nest by directed visual patterns

NASA Astrophysics Data System (ADS)

Kastberger, Gerald; Weihmann, Frank; Zierler, Martina; Hötzl, Thomas

2014-11-01

The open nesting behaviour of giant honeybees ( Apis dorsata) accounts for the evolution of a series of defence strategies to protect the colonies from predation. In particular, the concerted action of shimmering behaviour is known to effectively confuse and repel predators. In shimmering, bees on the nest surface flip their abdomens in a highly coordinated manner to generate Mexican wave-like patterns. The paper documents a further-going capacity of this kind of collective defence: the visual patterns of shimmering waves align regarding their directional characteristics with the projected flight manoeuvres of the wasps when preying in front of the bees' nest. The honeybees take here advantage of a threefold asymmetry intrinsic to the prey-predator interaction: (a) the visual patterns of shimmering turn faster than the wasps on their flight path, (b) they "follow" the wasps more persistently (up to 100 ms) than the wasps "follow" the shimmering patterns (up to 40 ms) and (c) the shimmering patterns align with the wasps' flight in all directions at the same strength, whereas the wasps have some preference for horizontal correspondence. The findings give evidence that shimmering honeybees utilize directional alignment to enforce their repelling power against preying wasps. This phenomenon can be identified as predator driving which is generally associated with mobbing behaviour (particularly known in selfish herds of vertebrate species), which is, until now, not reported in insects.

Viscous damped space structure for reduced jitter

NASA Technical Reports Server (NTRS)

Wilson, James F.; Davis, L. Porter

1987-01-01

A technique to provide modal vibration damping in high performance space structures was developed which uses less than one once of incompressible fluid. Up to 50 percent damping can be achieved which can reduce the settling times of the lowest structural mode by as much as 50 to 1. This concept allows the designers to reduce the weight of the structure while improving its dynamic performance. Damping by this technique is purely viscous and has been shown by test to be linear over 5 orders of input magnitude. Amplitudes as low as 0.2 microinch were demonstrated. Damping in the system is independent of stiffness and relatively insensitive to temperature.

Acoustic, respiratory kinematic and electromyographic effects of vocal training

NASA Astrophysics Data System (ADS)

Mendes, Ana Paula De Brito Garcia

The longitudinal effects of vocal training on the respiratory, phonatory and articulatory systems were investigated in this study. During four semesters, fourteen voice major students were recorded while speaking and singing. Acoustic, temporal, respiratory kinematic and electromyographic parameters were measured to determine changes in the three systems as a function of vocal training. Acoustic measures of the speaking voice included fundamental frequency, sound pressure level (SPL), percent jitter and shimmer, and harmonic-to-noise ratio. Temporal measures included duration of sentences, diphthongs and the closure durations of stop consonants. Acoustic measures of the singing voice included fundamental frequency and sound pressure level of the phonational range, vibrato pulses per second, vibrato amplitude variation and the presence of the singer's formant. Analysis of the data revealed that vocal training had a significant effect on the singing voice. Fundamental frequency and SPL of the 90% level and 90--10% of the phonational range increased significantly during four semesters of vocal training. Physiological data was collected from four subjects during three semesters of vocal training. Respiratory kinematic measures included lung volume, rib cage and abdominal excursions extracted from spoken sung samples. Descriptive statistics revealed that rib cage and abdominal excursions increased from the 1st to the 2nd semester and decrease from the 2nd to the 3rd semester of vocal training. Electromyographic measures of the pectoralis major, rectus abdominis and external obliques muscles revealed that burst duration means decreased from the 1st to the 2nd semester and increased from the 2nd to the 3rd semester. Peak amplitude means increased from the 1st to the 2nd and decreased from the 2nd to the 3rd semester of vocal training. Chest wall excursions and muscle force generation of the three muscles increased as the demanding level and the length of the phonatory

A scheme for a shot-to-shot, femtosecond-resolved pulse length and arrival time measurement of free electron laser x-ray pulses that overcomes the time jitter problem between the FEL and the laser

NASA Astrophysics Data System (ADS)

Juranić, P. N.; Stepanov, A.; Peier, P.; Hauri, C. P.; Ischebeck, R.; Schlott, V.; Radović, M.; Erny, C.; Ardana-Lamas, F.; Monoszlai, B.; Gorgisyan, I.; Patthey, L.; Abela, R.

2014-03-01

The recent entry of X-ray free electron lasers (FELs) to all fields of physics has created an enormous need, both from scientists and operators, for better characterization of the beam created by these facilities. Of particular interest is the measurement of the arrival time of the FEL pulse relative to a laser pump, for pump-probe experiments, and the measurement of the FEL pulse length. This article describes a scheme that corrects one of the major sources of uncertainty in these types of measurements, namely the jitter in the arrival time of the FEL relative to an experimental laser beam. The setup presented here uses a combination of THz streak cameras and a spectral encoding setup to reduce the effect of an FEL's jitter, leaving the pulse length as the only variable that can affect the accuracy of the pulse length and arrival time measurement. A discussion of underlying principles is also provided.

Investigating the Effects of Glottal Stop Productions on Voice in Children With Cleft Palate Using Multidimensional Voice Assessment Methods.

PubMed

Aydınlı, Fatma Esen; Özcebe, Esra; Kulak Kayıkçı, Maviş E; Yılmaz, Taner; Özgür, Fatma F

2016-11-01

The aim was to investigate the effects of glottal stop productions (GS) on voice in children with cleft palate using multidimensional voice assessment methods. This is a prospective case-control study. Children with repaired cleft palate (n = 34) who did not have any vocal fold lesions were separated into two groups based on the results of the articulation test. The glottal stop group (GSG) consisted of 17 children who had GS. The control group (CG) consisted of an equal number of age- and gender-matched children who did not have GS. The voice evaluation protocol included acoustic analysis, Pediatric Voice Handicap Index (pVHI), and perceptual analysis (Grade, Roughness, Breathiness, Asthenia, Strain method). The velopharyngeal statuses of the groups were compared using the nasopharyngoscopy and the nasometer. The total pVHI score and the subscales of the pVHI were found to be significantly higher in the GSG. The F0, jitter, and shimmer were found to be numerically higher in the GSG with the difference being statistically significant in jitter (P < 0.05). Audioperceptual analysis revealed a difference in overall voice quality and roughness between the groups. Greater incidence of significant velopharyngeal insufficiency and higher nasalance scores were found in the GSG (P < 0.05). These results may indicate that the vocal quality characteristics of children with GS differ from children who do not have this type of production. It is suggested that children with cleft palate who have GS should receive a comprehensive speech and language pathology intervention including voice therapy techniques. Copyright © 2016 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

31 CFR 363.136 - Do zero-percent certificates of indebtedness pay interest?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false Do zero-percent certificates of... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.136 Do zero-percent certificates of indebtedness pay interest? Zero-percent certificates of...

31 CFR 363.136 - Do zero-percent certificates of indebtedness pay interest?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false Do zero-percent certificates of... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.136 Do zero-percent certificates of indebtedness pay interest? Zero-percent certificates of...

31 CFR 363.136 - Do zero-percent certificates of indebtedness pay interest?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false Do zero-percent certificates of... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.136 Do zero-percent certificates of indebtedness pay interest? Zero-percent certificates of...

31 CFR 363.136 - Do zero-percent certificates of indebtedness pay interest?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false Do zero-percent certificates of... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.136 Do zero-percent certificates of indebtedness pay interest? Zero-percent certificates of...

Transmission line transformer for reliable and low-jitter triggering of a railgap switch

NASA Astrophysics Data System (ADS)

Verma, Rishi; Mishra, Ekansh; Sagar, Karuna; Meena, Manraj; Shyam, Anurag

2014-09-01

The performance of railgap switch critically relies upon multichannel breakdown between the extended electrodes (rails) in order to ensure distributed current transfer along electrode length and to minimize the switch inductance. The initiation of several simultaneous arc channels along the switch length depends on the gap triggering technique and on the rate at which the electric field changes within the gap. This paper presents design, construction, and output characteristics of a coaxial cable based three-stage transmission line transformer (TLT) that is capable of initiating multichannel breakdown in a high voltage, low inductance railgap switch. In each stage three identical lengths of URM67 coaxial cables have been used in parallel and they have been wounded in separate cassettes to enhance the isolation of the output of transformer from the input. The cascaded output impedance of TLT is ˜50 Ω. Along with multi-channel formation over the complete length of electrode rails, significant reduction in jitter (≤2 ns) and conduction delay (≤60 ns) has been observed by the realization of large amplitude (˜80 kV), high dV/dt (˜6 kV/ns) pulse produced by the indigenously developed TLT based trigger generator. The superior performance of TLT over conventional pulse transformer for railgap triggering application has been compared and demonstrated experimentally.

21 CFR 331.20 - Determination of percent contribution of active ingredients.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 5 2011-04-01 2011-04-01 false Determination of percent contribution of active... Procedures § 331.20 Determination of percent contribution of active ingredients. To determine the percent contribution of an antacid active ingredient, place an accurately weighed amount of the antacid active...

21 CFR 331.20 - Determination of percent contribution of active ingredients.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 5 2012-04-01 2012-04-01 false Determination of percent contribution of active... Procedures § 331.20 Determination of percent contribution of active ingredients. To determine the percent contribution of an antacid active ingredient, place an accurately weighed amount of the antacid active...

21 CFR 331.20 - Determination of percent contribution of active ingredients.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 5 2013-04-01 2013-04-01 false Determination of percent contribution of active... Procedures § 331.20 Determination of percent contribution of active ingredients. To determine the percent contribution of an antacid active ingredient, place an accurately weighed amount of the antacid active...

21 CFR 331.20 - Determination of percent contribution of active ingredients.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 5 2014-04-01 2014-04-01 false Determination of percent contribution of active... Procedures § 331.20 Determination of percent contribution of active ingredients. To determine the percent contribution of an antacid active ingredient, place an accurately weighed amount of the antacid active...

G-Jitter Induced Magnetohydrodynamics Flow of Nanofluid with Constant Convective Thermal and Solutal Boundary Conditions

PubMed Central

Uddin, Mohammed J.; Khan, Waqar A.; Ismail, Ahmad Izani Md.

2015-01-01

Taking into account the effect of constant convective thermal and mass boundary conditions, we present numerical solution of the 2-D laminar g-jitter mixed convective boundary layer flow of water-based nanofluids. The governing transport equations are converted into non-similar equations using suitable transformations, before being solved numerically by an implicit finite difference method with quasi-linearization technique. The skin friction decreases with time, buoyancy ratio, and thermophoresis parameters while it increases with frequency, mixed convection and Brownian motion parameters. Heat transfer rate decreases with time, Brownian motion, thermophoresis and diffusion-convection parameters while it increases with the Reynolds number, frequency, mixed convection, buoyancy ratio and conduction-convection parameters. Mass transfer rate decreases with time, frequency, thermophoresis, conduction-convection parameters while it increases with mixed convection, buoyancy ratio, diffusion-convection and Brownian motion parameters. To the best of our knowledge, this is the first paper on this topic and hence the results are new. We believe that the results will be useful in designing and operating thermal fluids systems for space materials processing. Special cases of the results have been compared with published results and an excellent agreement is found. PMID:25933066

Improvement of dem Generation from Aster Images Using Satellite Jitter Estimation and Open Source Implementation

NASA Astrophysics Data System (ADS)

Girod, L.; Nuth, C.; Kääb, A.

2015-12-01

The Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) system embarked on the Terra (EOS AM-1) satellite has been a source of stereoscopic images covering the whole globe at a 15m resolution at a consistent quality for over 15 years. The potential of this data in terms of geomorphological analysis and change detection in three dimensions is unrivaled and needs to be exploited. However, the quality of the DEMs and ortho-images currently delivered by NASA (ASTER DMO products) is often of insufficient quality for a number of applications such as mountain glacier mass balance. For this study, the use of Ground Control Points (GCPs) or of other ground truth was rejected due to the global "big data" type of processing that we hope to perform on the ASTER archive. We have therefore developed a tool to compute Rational Polynomial Coefficient (RPC) models from the ASTER metadata and a method improving the quality of the matching by identifying and correcting jitter induced cross-track parallax errors. Our method outputs more accurate DEMs with less unmatched areas and reduced overall noise. The algorithms were implemented in the open source photogrammetric library and software suite MicMac.

The 25 percent-efficient GaAs Cassegrainian concentrator cell

NASA Technical Reports Server (NTRS)

Hamaker, H. C.; Grounner, M.; Kaminar, N. R.; Kuryla, M. S.; Ladle, M. J.; Liu, D. D.; Macmillan, H. F.; Partain, L. D.; Virshup, G. F.; Werthen, J. G.

1989-01-01

Very high-efficiency GaAs Cassegrainian solar cells have been fabricated in both the n-p and p-n configurations. The n-p configuration exhibits the highest efficiency at concentration, the best cells having an efficiency eta of 24.5 percent (100X, AM0, temperature T = 28 C). Although the cells are designed for operation at this concentration, peak efficiency is observed near 300 suns (eta = 25.1 percent). To our knowledge, this is the highest reported solar cell efficiency for space applications. The improvement in efficiency over that reported at the previous SPRAT conference is attributed primarily to lower series resistance and improved grid-line plating procedures. Using previously measured temperature coefficients, researchers estimate that the n-p GaAs cells should deliver approximately 22.5 percent efficiency at the operating conditions of 100 suns and T = 80 C. This performance exceeds the NASA program goal of 22 percent for the Cassegrainian cell. One hundred Cassegrainian cells have been sent to NASA as deliverables, sixty-eight in the n-p configuration and thirty-two in the p-n configuration.

80-GHz AlGaInAs/InP 1.55 μm colliding-pulse mode-locked laser with low divergence angle and timing jitter

NASA Astrophysics Data System (ADS)

Hou, L. P.; Haji, M.; Li, C.; Qiu, B. C.; Bryce, A. C.

2011-07-01

We present an 80-GHz λ ~ 1.55 μm passively colliding-pulse mode-locked laser based on a novel AlGaInAs/InP epitaxial structure, which consists of a strained 3-quantum-well active layer incorporated with a passive far-field reduction layer. The device generated 910 fs pulses with a state-of-art timing jitter value of 190 fs (4 - 80 MHz), while demonstrating a low divergence angle (12.7°×26.3°) with two fold butt coupling efficiency to a flat cleaved single mode fiber when compared with the conventional mode-locked laser.

28 percent efficient GaAs concentrator solar cells

NASA Technical Reports Server (NTRS)

Macmillan, H. F.; Hamaker, H. C.; Kaminar, N. R.; Kuryla, M. S.; Ladle Ristow, M.

1988-01-01

AlGaAs/GaAs heteroface solar concentrator cells which exhibit efficiencies in excess of 27 percent at high solar concentrations (over 400 suns, AM1.5D, 100 mW/sq cm) have been fabricated with both n/p and p/n configurations. The best n/p cell achieved an efficiency of 28.1 percent around 400 suns, and the best p/n cell achieved an efficiency of 27.5 percent around 1000 suns. The high performance of these GaAs concentrator cells compared to earlier high-efficiency cells was due to improved control of the metal-organic chemical vapor deposition growth conditions and improved cell fabrication procedures (gridline definition and edge passivation). The design parameters of the solar cell structures and optimized grid pattern were determined with a realistic computer modeling program. An evaluation of the device characteristics and a discussion of future GaAs concentrator cell development are presented.

The Texas Ten Percent Plan's Impact on College Enrollment

ERIC Educational Resources Information Center

Daugherty, Lindsay; Martorell, Paco; McFarlin, Isaac, Jr.

2014-01-01

The Texas Ten Percent Plan (TTP) provides students in the top 10 percent of their high-school class with automatic admission to any public university in the state, including the two flagship schools, the University of Texas at Austin and Texas A&M. Texas created the policy in 1997 after a federal appellate court ruled that the state's previous…

0.4 Percent Scale Space Launch System Wind Tunnel Test

NASA Image and Video Library

2011-11-15

0.4 Percent Scale Space Launch System Wind Tunnel Test 0.4 Percent Scale SLS model installed in the NASA Langley Research Center Unitary Plan Wind Tunnel Test Section 1 for aerodynamic force and movement testing.

Percent Emphysema and Right Ventricular Structure and Function

PubMed Central

Grau, Maria; Lima, Joao A.; Hoffman, Eric A.; Bluemke, David A.; Carr, J. Jeffrey; Chahal, Harjit; Enright, Paul L; Jain, Aditya; Prince, Martin R.; Kawut, Steven M.

2013-01-01

Background: Severe COPD can lead to cor pulmonale and emphysema and is associated with impaired left ventricular (LV) filling. We evaluated whether emphysema and airflow obstruction would be associated with changes in right ventricular (RV) structure and function and whether these associations would differ by smoking status. Methods: The Multi-Ethnic Study of Atherosclerosis (MESA) performed cardiac MRI on 5,098 participants without clinical cardiovascular disease aged 45 to 84 years. RV and emphysema measures were available for 4,188 participants. Percent emphysema was defined as the percentage of voxels below −910 Hounsfield units in the lung windows on cardiac CT scans. Generalized additive models were used to control for confounders and adjust for respective LV parameters. Results: Participants consisted of 13% current smokers, 36% former smokers, and 52% never smokers. Percent emphysema was inversely associated with RV end-diastolic volume, stroke volume, cardiac output, and mass prior to adjustment for LV measures. After adjustment for LV end-diastolic volume, greater percent emphysema was associated with greater RV end-diastolic volume (+1.5 mL, P = .03) among current smokers, smaller RV end-diastolic volume (−0.8 mL, P = .02) among former smokers, and similar changes among never smokers. Conclusions: Percent emphysema was associated with smaller RV volumes and lower mass. The relationship of emphysema to cardiac function is complex but likely involves increased pulmonary vascular resistance, predominantly with reduced cardiac output, pulmonary hyperinflation, and accelerated cardiopulmonary aging. PMID:23450302

Complex social waves of giant honeybees provoked by a dummy wasp support the special-agent hypothesis.

PubMed

Kastberger, Gerald; Weihmann, Frank; Hoetzl, Thomas

2010-03-01

The social waves in giant honeybees termed as shimmering are more complex than mexican waves. it has been demonstrated1 that shimmering is triggered by special agents at the nest surface. in this paper, we have used a nest that originated by amalgamation of two previously separated nests and stimulated waves by a dummy wasp moved on a miniature cable car. we illustrate the plausibility of the special-agent hypothesis1 also for complex shimmering processes.

Complex social waves of giant honeybees provoked by a dummy wasp support the special-agent hypothesis

PubMed Central

Weihmann, Frank; Hoetzl, Thomas

2010-01-01

The social waves in giant honeybees termed as shimmering are more complex than mexican waves. it has been demonstrated1 that shimmering is triggered by special agents at the nest surface. in this paper, we have used a nest that originated by amalgamation of two previously separated nests and stimulated waves by a dummy wasp moved on a miniature cable car. we illustrate the plausibility of the special-agent hypothesis1 also for complex shimmering processes. PMID:20585516

Serum Predictors of Percent Lean Mass in Young Adults.

PubMed

Lustgarten, Michael S; Price, Lori L; Phillips, Edward M; Kirn, Dylan R; Mills, John; Fielding, Roger A

2016-08-01

Lustgarten, MS, Price, LL, Phillips, EM, Kirn, DR, Mills, J, and Fielding, RA. Serum predictors of percent lean mass in young adults. J Strength Cond Res 30(8): 2194-2201, 2016-Elevated lean (skeletal muscle) mass is associated with increased muscle strength and anaerobic exercise performance, whereas low levels of lean mass are associated with insulin resistance and sarcopenia. Therefore, studies aimed at obtaining an improved understanding of mechanisms related to the quantity of lean mass are of interest. Percent lean mass (total lean mass/body weight × 100) in 77 young subjects (18-35 years) was measured with dual-energy x-ray absorptiometry. Twenty analytes and 296 metabolites were evaluated with the use of the standard chemistry screen and mass spectrometry-based metabolomic profiling, respectively. Sex-adjusted multivariable linear regression was used to determine serum analytes and metabolites significantly (p ≤ 0.05 and q ≤ 0.30) associated with the percent lean mass. Two enzymes (alkaline phosphatase and serum glutamate oxaloacetate aminotransferase) and 29 metabolites were found to be significantly associated with the percent lean mass, including metabolites related to microbial metabolism, uremia, inflammation, oxidative stress, branched-chain amino acid metabolism, insulin sensitivity, glycerolipid metabolism, and xenobiotics. Use of sex-adjusted stepwise regression to obtain a final covariate predictor model identified the combination of 5 analytes and metabolites as overall predictors of the percent lean mass (model R = 82.5%). Collectively, these data suggest that a complex interplay of various metabolic processes underlies the maintenance of lean mass in young healthy adults.

Superfluid helium sloshing dynamics induced oscillations and fluctuations of angular momentum, force and moment actuated on spacecraft driven by gravity gradient or jitter acceleration associated with slew motion

NASA Technical Reports Server (NTRS)

Hung, R. J.

1994-01-01

The generalized mathematical formulation of sloshing dynamics for partially filled liquid of cryogenic superfluid helium II in dewar containers driven by the gravity gradient and jitter accelerations associated with slew motion for the purpose to perform scientific observation during the normal spacecraft operation are investigated. An example is given with the Advanced X-Ray Astrophysics Facility-Spectroscopy (AXAF-S) for slew motion which is responsible for the sloshing dynamics. The jitter accelerations include slew motion, spinning motion, atmospheric drag on the spacecraft, spacecraft attitude motions arising from machinery vibrations, thruster firing, pointing control of spacecraft, crew motion, etc. Explicit mathematical expressions to cover these forces acting on the spacecraft fluid systems are derived. The numerical computation of sloshing dynamics is based on the non-inertia frame spacecraft bound coordinate, and solve time-dependent, three-dimensional formulations of partial differential equations subject to initial and boundary conditions. The explicit mathematical expressions of boundary conditions to cover capillary force effect on the liquid-vapor interface in microgravity environments are also derived. The formulations of fluid moment and angular moment fluctuations in fluid profiles induced by the sloshing dynamics, together with fluid stress and moment fluctuations exerted on the spacecraft dewar containers have also been derived. Examples are also given for cases applicable to the AXAF-S spacecraft sloshing dynamics associated with slew motion.

`Special agents' trigger social waves in giant honeybees ( Apis dorsata)

NASA Astrophysics Data System (ADS)

Schmelzer, Evelyn; Kastberger, Gerald

2009-12-01

Giant honeybees ( Apis dorsata) nest in the open and have therefore evolved a variety of defence strategies. Against predatory wasps, they produce highly coordinated Mexican wavelike cascades termed ‘shimmering’, whereby hundreds of bees flip their abdomens upwards. Although it is well known that shimmering commences at distinct spots on the nest surface, it is still unclear how shimmering is generated. In this study, colonies were exposed to living tethered wasps that were moved in front of the experimental nest. Temporal and spatial patterns of shimmering were investigated in and after the presence of the wasp. The numbers and locations of bees that participated in the shimmering were assessed, and those bees that triggered the waves were identified. The findings reveal that the position of identified trigger cohorts did not reflect the experimental path of the tethered wasp. Instead, the trigger centres were primarily arranged in the close periphery of the mouth zone of the nest, around those parts where the main locomotory activity occurs. This favours the ‘special-agents’ hypothesis that suggest that groups of specialized bees initiate the shimmering.

The timbre model

NASA Astrophysics Data System (ADS)

Jensen, Kristoffer

2002-11-01

A timbre model is proposed for use in multiple applications. This model, which encompasses all voiced isolated musical instruments, has an intuitive parameter set, fixed size, and separates the sounds in dimensions akin to the timbre dimensions as proposed in timbre research. The analysis of the model parameters is fully documented, and it proposes, in particular, a method for the estimation of the difficult decay/release split-point. The main parameters of the model are the spectral envelope, the attack/release durations and relative amplitudes, and the inharmonicity and the shimmer and jitter (which provide both for the slow random variations of the frequencies and amplitudes, and also for additive noises). Some of the applications include synthesis, where a real-time application is being developed with an intuitive gui, classification, and search of sounds based on the content of the sounds, and a further understanding of acoustic musical instrument behavior. In order to present the background of the model, this presentation will start with sinusoidal A/S, some timbre perception research, then present the timbre model, show the validity for individual music instrument sounds, and finally introduce some expression additions to the model.

[Applicability of voice acoustic analysis with vocal loading testto diagnostics of occupational voice diseases].

PubMed

Niebudek-Bogusz, Ewa; Sliwińska-Kowalska, Mariola

2006-01-01

An assessment of the vocal system, as a part of the medical certification of occupational diseases, should be objective and reliable. Therefore, interest in the method of acoustic voice analysis enabling objective assessment of voice parameters is still growing. The aim of the present study was to evaluate the applicability of acoustic analysis with vocal loading test to the diagnostics of occupational voice disorders. The results of acoustic voice analysis were compared using IRIS software for phoniatrics, before and after a 30-min vocal loading test in 35 female teachers with diagnosed occupational voice disorders (group I) and in 31 female teachers with functional dysphonia (group II). In group I, vocal effort produced significant abnormalities in voice acoustic parameters, compared to group II. These included significantly increased mean fundamental frequency (Fo) value (by 11 Hz) and worsened jitter, shimmer and NHR parameters. Also, the percentage of subjects showing abnormalities in voice acoustic analysis was higher in this group. Conducting voice acoustic analysis before and after the vocal loading test makes it possible to objectively confirm irreversible voice impairments in persons with work-related pathologies of the larynx, which is essential for medical certification of occupational voice diseases.

Human voice quality measurement in noisy environments.

PubMed

Ueng, Shyh-Kuang; Luo, Cheng-Ming; Tsai, Tsung-Yu; Yeh, Hsuan-Chen

2015-01-01

Computerized acoustic voice measurement is essential for the diagnosis of vocal pathologies. Previous studies showed that ambient noises have significant influences on the accuracy of voice quality assessment. This paper presents a voice quality assessment system that can accurately measure qualities of voice signals, even though the input voice data are contaminated by low-frequency noises. The ambient noises in our living rooms and laboratories are collected and the frequencies of these noises are analyzed. Based on the analysis, a filter is designed to reduce noise level of the input voice signal. Then, improved numerical algorithms are employed to extract voice parameters from the voice signal to reveal the health of the voice signal. Compared with MDVP and Praat, the proposed method outperforms these two widely used programs in measuring fundamental frequency and harmonic-to-noise ratio, and its performance is comparable to these two famous programs in computing jitter and shimmer. The proposed voice quality assessment method is resistant to low-frequency noises and it can measure human voice quality in environments filled with noises from air-conditioners, ceiling fans and cooling fans of computers.

Laryngeal mucosa elasticity and viscosity in high and low relative air humidity.

PubMed

Hemler, R J; Wieneke, G H; Lebacq, J; Dejonckere, P H

2001-03-01

In earlier work we showed that low relative humidity (RH) of inhaled air causes acoustic voice parameters such as jitter and shimmer to deteriorate. Other authors have shown negative effects on vocal efficiency. To explain these changes in the mechanical properties of the vocal folds, the effects of changes in RH of the air passing over microdissected mucosa of sheep larynges were studied. The dissected surface of the tissue specimen just touched Ringer solution and air of varying RH was blown over the specimen. The mucosa specimen was subjected to sinusoidal oscillations of length (strain) and the resulting force (stress) was measured. The gain and phase angle between the imposed strain and resulting stress were measured, and elasticity and viscosity were calculated. Two different air conditions were tested: air with high RH (100%) vs air with low RH (0%). Viscosity and stiffness increased significantly in both ambient conditions (P < 0.01). Dry dehydrating air resulted in a stiffer and more viscous cover than humid air (P < 0.001). These changes in mechanical characteristics may contribute to the effects on voice parameters described in earlier work.

Acoustic characteristics of phonation in "wet voice" conditions.

PubMed

Murugappan, Shanmugam; Boyce, Suzanne; Khosla, Sid; Kelchner, Lisa; Gutmark, Ephraim

2010-04-01

A perceptible change in phonation characteristics after a swallow has long been considered evidence that food and/or drink material has entered the laryngeal vestibule and is on the surface of the vocal folds as they vibrate. The current paper investigates the acoustic characteristics of phonation when liquid material is present on the vocal folds, using ex vivo porcine larynges as a model. Consistent with instrumental examinations of swallowing disorders or dysphagia in humans, three liquids of different Varibar viscosity ("thin liquid," "nectar," and "honey") were studied at constant volume. The presence of materials on the folds during phonation was generally found to suppress the higher frequency harmonics and generate intermittent additional frequencies in the low and high end of the acoustic spectrum. Perturbation measures showed a higher percentage of jitter and shimmer when liquid material was present on the folds during phonation, but they were unable to differentiate statistically between the three fluid conditions. The finite correlation dimension and positive Lyapunov exponent measures indicated that the presence of materials on the vocal folds excited a chaotic system. Further, these measures were able to reliably differentiate between the baseline and different types of liquid on the vocal folds.

Using Hyaluronic Acid for Improving Vocal Function in a Prepubescent Boy With an Atrophied Right Vocal Fold.

PubMed

Cohen, Wendy; Wynne, David McGregor

2015-07-01

A single case study is reported of a child who underwent several surgical procedures as result of congenital grade III subglottic stenosis. The anterior aspect of the right vocal cord was damaged and underwent atrophy during one of these procedures. Now, an active 10-year-old, the patient has become increasingly aware of his vocal limitations on functional activities. Injection of hyaluronic acid into the vocal folds has been known to provide improved voice quality in adults although there are no known cases reported of this procedure in children. This article reports voice outcomes after injection of hyaluronic acid into the Reinke's space in a single case study. Voice recordings were made before, after, and 1 month after injection. The voice recordings were subject to acoustic and perceptual analysis. Post and follow-up voice recordings demonstrate decreased jitter, shimmer, and harmonics-to-noise ratio. Perceptual evaluation indicates improved voice quality. Injection of hyaluronic acid in children who require voice augmentation is possible and may contribute to increased vocal function and improved voice outcomes. Copyright © 2015 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Sloshing of Cryogenic Helium Driven by Lateral Impulse/Gravity Gradient-Dominated/or g-Jitter-Dominated Accelerations and Orbital Dynamics

NASA Technical Reports Server (NTRS)

Hung, R. J.; Long, Y. T.; Zu, G. J.

1996-01-01

The coupling of slosh dynamics within a partially filled rotating dewar of superfluid helium 11 with spacecraft orbital dynamics is investigated in response to the environmental disturbances of (a) lateral impulses, (b) gravity gradients and (c) g-jitter forces. The purpose of this study is to investigate how the coupling of helium 11 fluid slosh dynamics driven by three cases of environmental force with spacecraft dynamics can affect the bubble deformations and their associated fluid and spacecraft mass centre fluctuations. The numerical computation of slosh dynamics is based on a rotational frame, while the spacecraft dynamics is associated with a non-rotational frame. Results show that the major contribution of orbital dynamics is driven by coupling with slosh dynamics. Neglecting the effect of slosh dynamics acting on the spacecraft may lead to the wrong results for the development of orbital and attitude control techniques.

7 CFR 762.129 - Percent of guarantee and maximum loss.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 7 2014-01-01 2014-01-01 false Percent of guarantee and maximum loss. 762.129 Section 762.129 Agriculture Regulations of the Department of Agriculture (Continued) FARM SERVICE AGENCY, DEPARTMENT OF AGRICULTURE SPECIAL PROGRAMS GUARANTEED FARM LOANS § 762.129 Percent of guarantee and maximum...

12 CFR 741.4 - Insurance premium and one percent deposit.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Insurance premium and one percent deposit. 741... Insurance premium and one percent deposit. (a) Scope. This section implements the requirements of Section... payment of an insurance premium. (b) Definitions. For purposes of this section: Available assets ratio...

31 CFR 363.144 - Can I redeem my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false Can I redeem my zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.144 Can I redeem my zero-percent certificate of indebtedness? You can redeem...

31 CFR 363.144 - Can I redeem my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false Can I redeem my zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.144 Can I redeem my zero-percent certificate of indebtedness? You can redeem...

31 CFR 363.144 - Can I redeem my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false Can I redeem my zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.144 Can I redeem my zero-percent certificate of indebtedness? You can redeem...

12 CFR 741.4 - Insurance premium and one percent deposit.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Insurance premium and one percent deposit. 741... Insurance premium and one percent deposit. (a) Scope. This section implements the requirements of Section... payment of an insurance premium. (b) Definitions. For purposes of this section: (1) Available assets ratio...

[Clinical study on vocal cords spontaneous rehabilitation after CO2 laser surgery].

PubMed

Zhang, Qingxiang; Hu, Huiying; Sun, Guoyan; Yu, Zhenkun

2014-10-01

To study the spontaneous rehabilitation and phonation quality of vocal cords after different types of CO2 laser microsurgery. Surgical procedures based on Remacle system Type I, Type II, Type III, Type IV and Type V a respectively. Three hundred and fifteen cases with hoarseness based on strobe laryngoscopy results were prospectively assigned to different group according to vocal lesions apperence,vocal vibration and imaging of larynx CT/MRI. Each group holded 63 cases. The investigation included the vocal cords morphological features,the patients' subjective feelings and objective results of vocal cords. There are no severe complications for all patients in perioperative period. Vocal scar found in Type I ,1 case; Type II, 9 cases ;Type III, 47 cases; Type IV, 61 cases and Type Va 63 cases respectively after surgery. The difference of Vocal scar formation after surgery between surgical procedures are statistical significance (χ2 = 222.24, P < 0.05). Hoarseness improved after the surgery in 59 cases of Type I , 51 cases of Type II, 43 cases of Type III, 21 cases of Type IV and 17 cases of Type Va. There are statistically significance (χ2 = 89.46, P < 0.05) between different surgical procedures. The parameters of strobe laryngoscope: there are statistical significance on jitter between procedures (F 44.51, P < 0.05), but without difference within Type I and Type II (P > 0.05). This happened in shimmer parameter and the maximum phonation time (MPT) as jitter. There are no statistical significance between Type IV and Type Va on MPT (P > 0.05). Morphological and functional rehabilitation of vocal cord will be affected obviously when the body layer is injured. The depth and range of the CO2 laser microsurgery are the key factors affecting the vocal rehabilitation.

49 CFR 173.182 - Barium azide-50 percent or more water wet.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 2 2013-10-01 2013-10-01 false Barium azide-50 percent or more water wet. 173.182 Section 173.182 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more...

30 CFR 57.22236 - Actions at 1.0 percent methane (VI mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Actions at 1.0 percent methane (VI mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22236 Actions at 1.0 percent methane (VI mines). If methane reaches 1.0 percent in the mine atmosphere, all persons other than...

30 CFR 57.22239 - Actions at 2.0 percent methane (IV mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Actions at 2.0 percent methane (IV mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22239 Actions at 2.0 percent methane (IV mines). If methane reaches 2.0 percent in the mine atmosphere, all persons other than...

30 CFR 57.22239 - Actions at 2.0 percent methane (IV mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Actions at 2.0 percent methane (IV mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22239 Actions at 2.0 percent methane (IV mines). If methane reaches 2.0 percent in the mine atmosphere, all persons other than...

30 CFR 57.22236 - Actions at 1.0 percent methane (VI mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Actions at 1.0 percent methane (VI mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22236 Actions at 1.0 percent methane (VI mines). If methane reaches 1.0 percent in the mine atmosphere, all persons other than...

Training for Defense? From Stochastic Traits to Synchrony in Giant Honey Bees (Apis dorsata).

PubMed

Weihmann, Frank; Hoetzl, Thomas; Kastberger, Gerald

2012-08-30

In Giant Honey Bees, abdomen flipping happens in a variety of contexts. It can be either synchronous or cascaded, such as in the collective defense traits of shimmering and rearing-up, or it can happen as single-agent behavior. Abdomen flipping is also involved in flickering behavior, which occurs regularly under quiescent colony state displaying singular or collective traits, with stochastic, and (semi-) synchronized properties. It presumably acts via visual, mechanoceptive, and pheromonal pathways and its goals are still unknown. This study questions whether flickering is preliminary to shimmering which is subject of the fs (flickering-shimmering)-transition hypothesis? We tested the respective prediction that trigger sites (ts) at the nest surface (where shimmering waves had been generated) show higher flickering activity than the alternative non-trigger sites (nts). We measured the flickering activity of ts- and nts-surface bees from two experimental nests, before and after the colony had been aroused by a dummy wasp. Arousal increased rate and intensity of the flickering activity of both ts- and nts cohorts (P < 0.05), whereby the flickering intensity of ts-bees were higher than that of nts-bees (P < 0.05). Under arousal, the colonies also increased the number of flickering-active ts- and nts-cohorts (P < 0.05). This provides evidence that cohorts which are specialist at launching shimmering waves are found across the quiescent nest zone. It also proves that arousal may reinforce the responsiveness of quiescent curtain bees for participating in shimmering, practically by recruiting additional trigger site bees for expanding repetition of rate and intensity of shimmering waves. This finding confirms the fs-transition hypothesis and constitutes evidence that flickering is part of a basal colony-intrinsic information system. Furthermore, the findings disprove that the muscle activity associated with flickering would heat up the surface bees. Hence, surface bees

Training for Defense? From Stochastic Traits to Synchrony in Giant Honey Bees (Apis dorsata)

PubMed Central

Weihmann, Frank; Hoetzl, Thomas; Kastberger, Gerald

2012-01-01

In Giant Honey Bees, abdomen flipping happens in a variety of contexts. It can be either synchronous or cascaded, such as in the collective defense traits of shimmering and rearing-up, or it can happen as single-agent behavior. Abdomen flipping is also involved in flickering behavior, which occurs regularly under quiescent colony state displaying singular or collective traits, with stochastic, and (semi-) synchronized properties. It presumably acts via visual, mechanoceptive, and pheromonal pathways and its goals are still unknown. This study questions whether flickering is preliminary to shimmering which is subject of the fs (flickering-shimmering)-transition hypothesis? We tested the respective prediction that trigger sites (ts) at the nest surface (where shimmering waves had been generated) show higher flickering activity than the alternative non-trigger sites (nts). We measured the flickering activity of ts- and nts-surface bees from two experimental nests, before and after the colony had been aroused by a dummy wasp. Arousal increased rate and intensity of the flickering activity of both ts- and nts cohorts (P < 0.05), whereby the flickering intensity of ts-bees were higher than that of nts-bees (P < 0.05). Under arousal, the colonies also increased the number of flickering-active ts- and nts-cohorts (P < 0.05). This provides evidence that cohorts which are specialist at launching shimmering waves are found across the quiescent nest zone. It also proves that arousal may reinforce the responsiveness of quiescent curtain bees for participating in shimmering, practically by recruiting additional trigger site bees for expanding repetition of rate and intensity of shimmering waves. This finding confirms the fs-transition hypothesis and constitutes evidence that flickering is part of a basal colony-intrinsic information system. Furthermore, the findings disprove that the muscle activity associated with flickering would heat up the surface bees. Hence, surface bees

Does Percent Body Fat Predict Outcome in Anorexia Nervosa?

PubMed Central

Mayer, Laurel E.S.; Roberto, Christina A.; Glasofer, Deborah R.; Etu, Sarah Fischer; Gallagher, Dympna; Wang, Jack; Heymsfield, Steven B.; Pierson, Richard N.; Attia, Evelyn; Devlin, Michael J.; Walsh, B. Timothy

2009-01-01

Objective The goal of this study was to investigate the relationship of body composition and neuroendocrine levels with clinical outcome in women with anorexia nervosa in a relapse-prevention trial. Method Body composition and fasting cortisol and leptin levels were assessed before random assignment in 32 weight-recovered subjects with anorexia nervosa from the New York site of the Fluoxetine to Prevent Relapse in Women With Anorexia Nervosa trial. Clinical outcome at the end of study participation was defined using modified Morgan-Russell criteria (full, good, fair, poor), then dichotomized into treatment “success” or “failure.” Results In a binary logistic regression model examining the effect of percent body fat, body mass index, anorexia nervosa subtype, waist-to-hip ratio, and serum cortisol and leptin levels on treatment outcome, only percent body fat was significantly associated with outcome. Conclusions In recently weight-restored women with anorexia nervosa, lower percent body fat was associated with poor long-term outcome. PMID:17541059

86 Percent of Tops and 54 Percent of Slabs and Edgings Unused in Central Piedmont of South Carolina

Treesearch

William H.B. Haines

1953-01-01

In the West, 30 percent of pulpwood requirements are supplied by logging and mill residues. Most of this material is obtained from large lumber operations. In the Southeast, where portable sawmills and small and scattered timber tracts are characteristic, salvage is more difficult. However, the tremendous volume of available material stimulates considerable interest...

The 1.06 optical receiver. [avalanche photodiodes for laser range finders

NASA Technical Reports Server (NTRS)

Tomasetta, L. R.; Law, H. D.; Nakano, K.; Scholl, F. W.; Harris, J. S., Jr.

1978-01-01

High performance 1.06 micron m avalanche photodetectors (APDs), fabricated in the GaAlSb system, have high quantum efficiency (90 percent), high speed (risetime less than 60 ps) and low leakage currents (less than 50 na). The dark current represents more than an order of magnitude reduction compared to previously reported results. The high speed avalanche gain of these devices is between 20 and 50. The area uniformity is better than + or - 10 percent. GaAlAs APDs at 0.53 micron m have even faster speed, lower dark currents, and high speed gains of 100 to 200. Optical rangefinders based on measured APD performance parameters have far superior performance when compared to even ideal photomultiplier tubes in either a one color or two color rangefinder system. For a one color system, f factor of two lower time jitter can be achieved with identical transmitted power. The superiority of the APD based two color receiver is significant and exists in the entire range of desired time jitters (less than 100 ps) and received power levels.

Matter power spectrum and the challenge of percent accuracy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Aurel; Teyssier, Romain; Potter, Doug

2016-04-01

Future galaxy surveys require one percent precision in the theoretical knowledge of the power spectrum over a large range including very nonlinear scales. While this level of accuracy is easily obtained in the linear regime with perturbation theory, it represents a serious challenge for small scales where numerical simulations are required. In this paper we quantify the precision of present-day N -body methods, identifying main potential error sources from the set-up of initial conditions to the measurement of the final power spectrum. We directly compare three widely used N -body codes, Ramses, Pkdgrav3, and Gadget3 which represent three main discretisationmore » techniques: the particle-mesh method, the tree method, and a hybrid combination of the two. For standard run parameters, the codes agree to within one percent at k ≤1 h Mpc{sup −1} and to within three percent at k ≤10 h Mpc{sup −1}. We also consider the bispectrum and show that the reduced bispectra agree at the sub-percent level for k ≤ 2 h Mpc{sup −1}. In a second step, we quantify potential errors due to initial conditions, box size, and resolution using an extended suite of simulations performed with our fastest code Pkdgrav3. We demonstrate that the simulation box size should not be smaller than L =0.5 h {sup −1}Gpc to avoid systematic finite-volume effects (while much larger boxes are required to beat down the statistical sample variance). Furthermore, a maximum particle mass of M {sub p}=10{sup 9} h {sup −1}M{sub ⊙} is required to conservatively obtain one percent precision of the matter power spectrum. As a consequence, numerical simulations covering large survey volumes of upcoming missions such as DES, LSST, and Euclid will need more than a trillion particles to reproduce clustering properties at the targeted accuracy.« less

Vocal warm-up and breathing training for teachers: randomized clinical trial

PubMed Central

Pereira, Lílian Paternostro de Pina; Masson, Maria Lúcia Vaz; Carvalho, Fernando Martins

2015-01-01

OBJECTIVE To compare the effectiveness of two speech therapy interventions, vocal warm-up and breathing training, focusing on teachers’ voice quality. METHODS A single-blind, randomized, parallel clinical trial was conducted. The research included 31 20 to 60-year old teachers from a public school in Salvador, BA, Northeasatern Brazil, with minimum workloads of 20 hours a week, who have or have not reported having vocal alterations. The exclusion criteria were the following: being a smoker, excessive alcohol consumption, receiving additional speech therapy assistance while taking part in the study, being affected by upper respiratory tract infections, professional use of the voice in another activity, neurological disorders, and history of cardiopulmonary pathologies. The subjects were distributed through simple randomization in groups vocal warm-up (n = 14) and breathing training (n = 17). The teachers’ voice quality was subjectively evaluated through the Voice Handicap Index (Índice de Desvantagem Vocal, in the Brazilian version) and computerized voice analysis (average fundamental frequency, jitter, shimmer, noise, and glottal-to-noise excitation ratio) by speech therapists. RESULTS Before the interventions, the groups were similar regarding sociodemographic characteristics, teaching activities, and vocal quality. The variations before and after the intervention in self-assessment and acoustic voice indicators have not significantly differed between the groups. In the comparison between groups before and after the six-week interventions, significant reductions in the Voice Handicap Index of subjects in both groups were observed, as wells as reduced average fundamental frequencies in the vocal warm-up group and increased shimmer in the breathing training group. Subjects from the vocal warm-up group reported speaking more easily and having their voices more improved in a general way as compared to the breathing training group. CONCLUSIONS Both interventions

49 CFR 173.182 - Barium azide-50 percent or more water wet.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 2 2011-10-01 2011-10-01 false Barium azide-50 percent or more water wet. 173.182... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more water wet, must be packed in wooden boxes (4C1, 4C2, 4D, or 4F) or fiber drums (1G) with inner glass...

49 CFR 173.182 - Barium azide-50 percent or more water wet.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Barium azide-50 percent or more water wet. 173.182... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more water wet, must be packed in wooden boxes (4C1, 4C2, 4D, or 4F) or fiber drums (1G) with inner glass...

31 CFR 363.141 - How do I purchase a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false How do I purchase a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.141 How do I purchase a zero-percent certificate of indebtedness? (a...

31 CFR 363.141 - How do I purchase a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false How do I purchase a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.141 How do I purchase a zero-percent certificate of indebtedness? (a...

31 CFR 363.141 - How do I purchase a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false How do I purchase a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.141 How do I purchase a zero-percent certificate of indebtedness? (a...

31 CFR 363.141 - How do I purchase a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false How do I purchase a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.141 How do I purchase a zero-percent certificate of indebtedness? (a...

31 CFR 363.134 - What regulations cover a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false What regulations cover a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.134 What regulations cover a zero-percent certificate of indebtedness? The regulations in part 363...

31 CFR 363.134 - What regulations cover a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false What regulations cover a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.134 What regulations cover a zero-percent certificate of indebtedness? The regulations in part 363...

31 CFR 363.134 - What regulations cover a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false What regulations cover a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.134 What regulations cover a zero-percent certificate of indebtedness? The regulations in part 363...

31 CFR 363.134 - What regulations cover a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false What regulations cover a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.134 What regulations cover a zero-percent certificate of indebtedness? The regulations in part 363...

How I Love My 80 Percenters

NASA Technical Reports Server (NTRS)

Maturo, Anthony J.

2002-01-01

Don't ever take your support staff for granted. By support staff, I mean the people in personnel, logistics, and finance; the ones who can make things happen with a phone call or a signature, or by the same token frustrate you to no end by their inaction; these are people you must depend on. I've spent a lot of time thinking about how to cultivate relationships with my support staff that work to the advantage of both of us. The most important thing that have learned working with people, any people--and I will tell you how I learned this in a minute--is there are some folks you just can't motivate, so forget it, don't try; others you certainly can with a little psychology and some effort; and the best of the bunch, what I call the 80 percenters, you don't need to motivate because they're already on the team and performing beautifully. The ones you can't change are rocks. Face up to it, and just kick them out of your way. I have a reputation with the people who don't want to perform or be part of the team. They don't come near me. If someone's a rock, I pick up on it right away, and I will walk around him or her to find someone better. The ones who can be motivated I take time to nurture. I consider them my projects. A lot of times these wannabes are people who want to help but don't know how. Listen, you can work with them. Lots of people in organizations have the mindset that all that matters are the regulations. God forbid if you ever work outside those regulations. They've got one foot on that regulation and they're holding it tight like a baby holds a blanket. What you're looking for is that first sign that their minds are opening. Usually you hear it in their vocabulary. What used to sound like "We can't do that ... the regulations won't allow it ... we have never done this before," well, suddenly that changes to "We have options ... let's take a look at the options ... let me research this and get back to you." The 80 percenters you want to nurture too, but

Accuracy assessment of percent canopy cover, cover type, and size class

Treesearch

H. T. Schreuder; S. Bain; R. C. Czaplewski

2003-01-01

Truth for vegetation cover percent and type is obtained from very large-scale photography (VLSP), stand structure as measured by size classes, and vegetation types from a combination of VLSP and ground sampling. We recommend using the Kappa statistic with bootstrap confidence intervals for overall accuracy, and similarly bootstrap confidence intervals for percent...

30 CFR 57.22240 - Actions at 2.0 percent methane (V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Actions at 2.0 percent methane (V-A mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22240 Actions at 2.0 percent methane (V-A mines). If methane reaches 2.0 percent in the mine atmosphere, all persons other than...

30 CFR 57.22233 - Actions at 0.5 percent methane (I-C mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Actions at 0.5 percent methane (I-C mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22233 Actions at 0.5 percent methane (I-C mines). If methane reaches 0.5 percent in the mine atmosphere, ventilation changes...

30 CFR 57.22240 - Actions at 2.0 percent methane (V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Actions at 2.0 percent methane (V-A mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22240 Actions at 2.0 percent methane (V-A mines). If methane reaches 2.0 percent in the mine atmosphere, all persons other than...

30 CFR 57.22233 - Actions at 0.5 percent methane (I-C mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Actions at 0.5 percent methane (I-C mines). 57... MINES Safety Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22233 Actions at 0.5 percent methane (I-C mines). If methane reaches 0.5 percent in the mine atmosphere, ventilation changes...

Early Warning Look Ahead Metrics: The Percent Milestone Backlog Metric

NASA Technical Reports Server (NTRS)

Shinn, Stephen A.; Anderson, Timothy P.

2017-01-01

All complex development projects experience delays and corresponding backlogs of their project control milestones during their acquisition lifecycles. NASA Goddard Space Flight Center (GSFC) Flight Projects Directorate (FPD) teamed with The Aerospace Corporation (Aerospace) to develop a collection of Early Warning Look Ahead metrics that would provide GSFC leadership with some independent indication of the programmatic health of GSFC flight projects. As part of the collection of Early Warning Look Ahead metrics, the Percent Milestone Backlog metric is particularly revealing, and has utility as a stand-alone execution performance monitoring tool. This paper describes the purpose, development methodology, and utility of the Percent Milestone Backlog metric. The other four Early Warning Look Ahead metrics are also briefly discussed. Finally, an example of the use of the Percent Milestone Backlog metric in providing actionable insight is described, along with examples of its potential use in other commodities.

Irradiation effects on 17-7 PH stainless steel, A-201 carbon steel, and titanium-6-percent-aluminum-4-percent-vanadium alloy

NASA Technical Reports Server (NTRS)

Hasse, R. A.; Hartley, C. B.

1972-01-01

Irradiation effects on three materials from the NASA Plum Brook Reactor Surveillance Program were determined. An increase of 105 K in the nil-ductility temperature for A-201 steel was observed at a fluence of approximately 3.1 x 10 to the 18th power neutrons/sq cm (neutron energy E sub n greater than 1.0 MeV). Only minor changes in the mechanical properties of 17-7 PH stainless steel were observed up to a fluence of 2 x 10 to the 21st power neutrons/sq cm (E sub n greater than 1.0 MeV). The titanium-6-percent-aluminum-4-percent-vanadium alloy maintained its notch toughness up to a fluence of 1 x 10 to the 21st power neutrons/sq cm (E sub n greater than 1.0 MeV).

Development of high efficiency (14 percent) solar cell array module

NASA Technical Reports Server (NTRS)

Iles, P. A.; Khemthong, S.; Olah, S.; Sampson, W. J.; Ling, K. S.

1980-01-01

Most effort was concentrated on development of procedures to provide large area (3 in. diameter) high efficiency (16.5 percent AM1, 28 C) P+NN+ solar cells. Intensive tests with 3 in. slices gave consistently lower efficiency (13.5 percent). The problems were identified as incomplete formation of and optimum back surface field (BSF), and interaction of the BSF process and the shallow P+ junction. The problem was shown not to be caused by reduced quality of silicon near the edges of the larger slices.

31 CFR 363.135 - In what form is a zero-percent certificate of indebtedness issued?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false In what form is a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.135 In what form is a zero-percent certificate of indebtedness issued? A zero-percent certificate of...

31 CFR 363.135 - In what form is a zero-percent certificate of indebtedness issued?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false In what form is a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.135 In what form is a zero-percent certificate of indebtedness issued? A zero-percent certificate of...

31 CFR 363.135 - In what form is a zero-percent certificate of indebtedness issued?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false In what form is a zero-percent... REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.135 In what form is a zero-percent certificate of indebtedness issued? A zero-percent certificate of...

31 CFR 363.135 - In what form is a zero-percent certificate of indebtedness issued?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false In what form is a zero-percent... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.135 In what form is a zero-percent certificate of indebtedness issued? A zero-percent...

Relationship between breast sound speed and mammographic percent density

NASA Astrophysics Data System (ADS)

Sak, Mark; Duric, Nebojsa; Boyd, Norman; Littrup, Peter; Myc, Lukasz; Faiz, Muhammad; Li, Cuiping; Bey-Knight, Lisa

2011-03-01

Despite some shortcomings, mammography is currently the standard of care for breast cancer screening and diagnosis. However, breast ultrasound tomography is a rapidly developing imaging modality that has the potential to overcome the drawbacks of mammography. It is known that women with high breast densities have a greater risk of developing breast cancer. Measuring breast density is accomplished through the use of mammographic percent density, defined as the ratio of fibroglandular to total breast area. Using an ultrasound tomography (UST) prototype, we created sound speed images of the patient's breast, motivated by the fact that sound speed in a tissue is proportional to the density of the tissue. The purpose of this work is to compare the acoustic performance of the UST system with the measurement of mammographic percent density. A cohort of 251 patients was studied using both imaging modalities and the results suggest that the volume averaged breast sound speed is significantly related to mammographic percent density. The Spearman correlation coefficient was found to be 0.73 for the 175 film mammograms and 0.69 for the 76 digital mammograms obtained. Since sound speed measurements do not require ionizing radiation or physical compression, they have the potential to form the basis of a safe, more accurate surrogate marker of breast density.

Voice amplification versus vocal hygiene instruction for teachers with voice disorders: a treatment outcomes study.

PubMed

Roy, Nelson; Weinrich, Barbara; Gray, Steven D; Tanner, Kristine; Toledo, Sue Walker; Dove, Heather; Corbin-Lewis, Kim; Stemple, Joseph C

2002-08-01

Voice problems are common among schoolteachers. This prospective, randomized clinical trial used patient-based treatment outcomes measures combined with acoustic analysis to evaluate the effectiveness of two treatment programs. Forty-four voice-disordered teachers were randomly assigned to one of three groups: voice amplification using the ChatterVox portable amplifier (VA, n = 15), vocal hygiene (VH, n = 15), and a nontreatment control group (n = 14). Before and after a 6-week treatment phase, all teachers completed: (a) the Voice Handicap Index (VHI), an instrument designed to appraise the self-perceived psychosocial consequences of voice disorders; (b) a voice severity self-rating scale; and (c) an audiorecording for later acoustic analysis. Based on pre- and posttreatment comparisons, only the amplification group experienced significant reductions on mean VHI scores (p = .045), voice severity self-ratings (p = .012), and the acoustic measures of percent jitter (p = .031) and shimmer (p = .008). The nontreatment control group reported a significant increase in level of vocal handicap as assessed by the VHI (p = .012). Although most pre- to posttreatment changes were in the desired direction, no significant improvements were observed within the VH group on any of the dependent measures. Between-group comparisons involving the three possible pairings of the groups revealed a pattern of results to suggest that: (a) compared to the control group, both treatment groups (i.e., VA and VH) experienced significantly more improvement on specific outcomes measures and (b) there were no significant differences between the VA and VH groups to indicate superiority of one treatment over another. Results, however, from a posttreatment questionnaire regarding the perceived benefits of treatment revealed that, compared to the VH group, the VA group reported more clarity of their speaking and singing voice (p = .061), greater ease of voice production (p = .001), and greater

Acoustic characteristics of phonation in “wet voice” conditions

PubMed Central

Murugappan, Shanmugam; Boyce, Suzanne; Khosla, Sid; Kelchner, Lisa; Gutmark, Ephraim

2010-01-01

A perceptible change in phonation characteristics after a swallow has long been considered evidence that food and∕or drink material has entered the laryngeal vestibule and is on the surface of the vocal folds as they vibrate. The current paper investigates the acoustic characteristics of phonation when liquid material is present on the vocal folds, using ex vivo porcine larynges as a model. Consistent with instrumental examinations of swallowing disorders or dysphagia in humans, three liquids of different Varibar viscosity (“thin liquid,” “nectar,” and “honey”) were studied at constant volume. The presence of materials on the folds during phonation was generally found to suppress the higher frequency harmonics and generate intermittent additional frequencies in the low and high end of the acoustic spectrum. Perturbation measures showed a higher percentage of jitter and shimmer when liquid material was present on the folds during phonation, but they were unable to differentiate statistically between the three fluid conditions. The finite correlation dimension and positive Lyapunov exponent measures indicated that the presence of materials on the vocal folds excited a chaotic system. Further, these measures were able to reliably differentiate between the baseline and different types of liquid on the vocal folds. PMID:20370039

Effects of melody and technique on acoustical and musical features of western operatic singing voices.

PubMed

Larrouy-Maestri, Pauline; Magis, David; Morsomme, Dominique

2014-05-01

The operatic singing technique is frequently used in classical music. Several acoustical parameters of this specific technique have been studied but how these parameters combine remains unclear. This study aims to further characterize the Western operatic singing technique by observing the effects of melody and technique on acoustical and musical parameters of the singing voice. Fifty professional singers performed two contrasting melodies (popular song and romantic melody) with two vocal techniques (with and without operatic singing technique). The common quality parameters (energy distribution, vibrato rate, and extent), perturbation parameters (standard deviation of the fundamental frequency, signal-to-noise ratio, jitter, and shimmer), and musical features (fundamental frequency of the starting note, average tempo, and sound pressure level) of the 200 sung performances were analyzed. The results regarding the effect of melody and technique on the acoustical and musical parameters show that the choice of melody had a limited impact on the parameters observed, whereas a particular vocal profile appeared depending on the vocal technique used. This study confirms that vocal technique affects most of the parameters examined. In addition, the observation of quality, perturbation, and musical parameters contributes to a better understanding of the Western operatic singing technique. Copyright © 2014 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Differences in acoustic and perceptual parameters of the voice between elderly and young women at habitual and high intensity.

PubMed

Mazzetto de Menezes, Keyla S; Master, Suely; Guzman, Marco; Bortnem, Cori; Ramos, Luiz Roberto

2014-01-01

The present study aimed to compare elderly and young female voices in habitual and high intensity. The effect of increased intensity on the acoustic and perceptual parameters was assessed. Sound pressure level, fundamental frequency, jitter, shimmer, and harmonic to noise ratio were obtained at habitual and high intensity voice in a group of 30 elderly women and 30 young women. Perceptual assessment was also performed. Both groups demonstrated an increase in sound pressure level and fundamental frequency from habitual voice to high intensity voice. No differences were found between groups in any acoustic variables on samples recorded with habitual intensity level. No significant differences between groups were found in habitual intensity level for pitch, hoarseness, roughness, and breathiness. Asthenia and instability obtained significant higher values in elderly than young participants, whereas, the elderly demonstrated lower values for perceived tension and loudness than young subjects. Acoustic and perceptual measures do not demonstrate evident differences between elderly and young speakers in habitual intensity level. The parameters analyzed may lack the sensitivity necessary to detect differences in subjects with normal voices. Phonation with high intensity highlights differences between groups, especially in perceptual parameters. Therefore, high intensity should be included to compare elderly and young voice. Copyright © 2013 Elsevier España, S.L. All rights reserved.

[Voice acoustic study of plasma radiofrequency ablation for the treatment of laryngeal premalignant lesions].

PubMed

Zang, Y Z; Wan, B L; Jia, X D; Wang, G K

2016-11-01

Objective: To study the voice function effect of low temperature plasma radiofrequency ablation in the treatment of patients with laryngeal premalignant lesions. Method: Fifty cases of laryngeal premalignant lesions were treated with low temperature plasma radiofrequency ablation. All of the patients were examined by electronic laryngoscopy and acoustic analysis(F0，Jitter，Shimmer，NNE，HNR) in 2 weeks,1 month,3 months after surgery. Voice acoustic results were compared with a control group of 50 normal adults for the further analysis. Result: Fifty patients with laryngeal premalignant lesions were treated by low temperature plasma radiofrequency ablation.The result showed that 47 patients(94%)were successfully decannulated without serious complications, such as dyspnea, aphonia and anterior glottic stenosis. Acoustic analysis showed that F0,Jitter,Shimmer and NNE were significantly different from normal 2 weeks after surgery（ P <0.01）.Voice function recovered weakly 1 month after operation（ P <0.05）.There were no significant differences in the vocal parameters between plasma radiofrequency ablation group and control group 3 months after surgery( P >0.05). Conclusion: Radiofrequency coblation was a safe,minimally invasive and effective surgical method and can be widely used to treat laryngeal premalignant lesions．. Copyright© by the Editorial Department of Journal of Clinical Otorhinolaryngology Head and Neck Surgery.

31 CFR 363.146 - Who may purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false Who may purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.146 Who may purchase a payroll zero-percent...

31 CFR 363.146 - Who may purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false Who may purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.146 Who may purchase a payroll zero-percent...

31 CFR 363.146 - Who may purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false Who may purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.146 Who may purchase a payroll zero-percent...

31 CFR 363.146 - Who may purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false Who may purchase a payroll zero... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.146 Who may purchase a payroll zero-percent...

5 CFR 2636.304 - The 15 percent limitation on outside earned income.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 3 2010-01-01 2010-01-01 false The 15 percent limitation on outside earned income. 2636.304 Section 2636.304 Administrative Personnel OFFICE OF GOVERNMENT ETHICS GOVERNMENT... Noncareer Employees § 2636.304 The 15 percent limitation on outside earned income. (a) Limitation applicable...

School Designed To Use 80 Percent Less Energy

ERIC Educational Resources Information Center

American School and University, 1975

1975-01-01

The new Terraset Elementary School in Reston, Virginia, uses earth as a cover for the roof area and for about 80 percent of the wall area. A heat recovery system will be used with solar collectors playing a primary role in heating and cooling. (Author/MLF)

Evaluation of three percent Aqueous Film Forming Foam (AFFF) concentrates as fire fighting agents

NASA Astrophysics Data System (ADS)

Jablonski, E. J.

1981-04-01

A large-scale fire test program involving 20,000-square foot JP-4 fuel fires was conducted to evaluate the fire suppression effectiveness and compatibility of 3 percent Aqueous Film Forming Foam (AFFF) agents in Air Force fire fighting vehicles. Three commercially available 3 percent AFFF concentrates were tested in accordance with military specification MIL-F-24385B. Test results are summarized in Appendix A. As a result of these tests, an updated Revision C to this MIL SPEC has been accomplished with new requirements for both 3 percent and 6 percent AFFF extinguishing agents.

20 CFR 229.11 - 100 percent overall minimum.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SOCIAL SECURITY OVERALL MINIMUM GUARANTEE Social Security Overall Minimum Guarantee Defined § 229.11 100..., will not be less than 100 percent of the total family benefits payable under the Social Security Act if the employee's railroad service after 1936 were credited as social security earnings. Subpart F...

9 CFR 381.168 - Maximum percent of skin in certain poultry products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Maximum percent of skin in certain poultry products. 381.168 Section 381.168 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... Standards of Identity or Composition § 381.168 Maximum percent of skin in certain poultry products. The...

9 CFR 381.168 - Maximum percent of skin in certain poultry products.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Maximum percent of skin in certain poultry products. 381.168 Section 381.168 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... Standards of Identity or Composition § 381.168 Maximum percent of skin in certain poultry products. The...

Near-real-time cheatgrass percent cover in the Northern Great Basin, USA, 2015

USGS Publications Warehouse

Boyte, Stephen; Wylie, Bruce K.

2016-01-01

Cheatgrass (Bromus tectorum L.) dramatically changes shrub steppe ecosystems in the Northern Great Basin, United States.Current-season cheatgrass location and percent cover are difficult to estimate rapidly.We explain the development of a near-real-time cheatgrass percent cover dataset and map in the Northern Great Basin for the current year (2015), display the current year’s map, provide analysis of the map, and provide a website link to download the map (as a PDF) and the associated dataset.The near-real-time cheatgrass percent cover dataset and map were consistent with non-expedited, historical cheatgrass percent cover datasets and maps.Having cheatgrass maps available mid-summer can help land managers, policy makers, and Geographic Information Systems personnel as they work to protect socially relevant areas such as critical wildlife habitats.

32 CFR 48.508 - Certain 100 percent disability retirement.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., MILITARY AND CIVILIAN RETIRED SERVICEMAN'S FAMILY PROTECTION PLAN Annuity § 48.508 Certain 100 percent... duty as a direct result of armed conflict, or (b) His widow or children are not entitled to dependency...

A 99 percent purity molecular sieve oxygen generator

NASA Technical Reports Server (NTRS)

Miller, G. W.

1991-01-01

Molecular sieve oxygen generating systems (MSOGS) have become the accepted method for the production of breathable oxygen on military aircraft. These systems separate oxygen for aircraft engine bleed air by application of pressure swing adsorption (PSA) technology. Oxygen is concentrated by preferential adsorption in nitrogen in a zeolite molecular sieve. However, the inability of current zeolite molecular sieves to discriminate between oxygen and argon results in an oxygen purity limitations of 93-95 percent (both oxygen and argon concentrate). The goal was to develop a new PSA process capable of exceeding the present oxygen purity limitations. A novel molecular sieve oxygen concentrator was developed which is capable of generating oxygen concentrations of up to 99.7 percent directly from air. The process is comprised of four absorbent beds, two containing a zeolite molecular sieve and two containing a carbon molecular sieve. This new process may find use in aircraft and medical breathing systems, and industrial air separation systems. The commercial potential of the process is currently being evaluated.

Tricky Times for the Top 10 Percent Program

ERIC Educational Resources Information Center

Roach, Ronald

2007-01-01

Both supporters and critics of Texas' Top 10 Percent law have been surprised at its popularity, but some UT officials and legislators would like to see the program scaled back. As a Texas state legislator, Jim McReynolds, D-Lufkin, knows a thing or two about influencing the voting positions of his colleagues. This past spring, when Texas House…

Modeling percent tree canopy cover: a pilot study

Treesearch

John W. Coulston; Gretchen G. Moisen; Barry T. Wilson; Mark V. Finco; Warren B. Cohen; C. Kenneth Brewer

2012-01-01

Tree canopy cover is a fundamental component of the landscape, and the amount of cover influences fire behavior, air pollution mitigation, and carbon storage. As such, efforts to empirically model percent tree canopy cover across the United States are a critical area of research. The 2001 national-scale canopy cover modeling and mapping effort was completed in 2006,...

Can body mass index predict percent body fat and changes in percent body fat with weight loss in bariatric surgery patients?

PubMed

Carey, Daniel G; Raymond, Robert L

2008-07-01

The primary objective of this study was to assess the validity of body mass index (BMI) in predicting percent body fat and changes in percent body fat with weight loss in bariatric surgery patients. Twenty-two bariatric patients (17 female, five male) began the study designed to include 12 months of testing, including data collection within 1 week presurgery and 1 month, 3 months, 6 months, and 1 year postsurgery. Five female subjects were lost to the study between 6 months and 12 months postsurgery, resulting in 17 subjects (12 female, five male) completing the 12 months of testing. Variables measured in the study included height, weight, percent fat (% fat) by hydrostatic weighing, lean mass, fat mass, and basal metabolic rate. Regression analyses predicting % fat from BMI yielded the following results: presurgery r = 0.173, p = 0.479, standard error of estimate (SEE) = 3.86; 1 month r = 0.468, p = 0.043, SEE = 4.70; 3 months r = 0.553, p = 0.014, SEE = 6.2; 6 months r = 0.611, p = 0.005, SEE = 5.88; 12 months r = 0.596, p = 0.007, SEE = 7.13. Regression analyses predicting change in % fat from change in BMI produced the following results: presurgery to 1 month r = -0.134, p = 0.583, SEE = 2.44%; 1-3 months r = 0.265, p = 0.272, SEE = 2.36%; 3-6 months r = 0.206, p = 0.398, SEE = 3.75%; 6-12 months r = 0.784, p = 0.000, SEE = 3.20. Although some analyses resulted in significant correlation coefficients (p < 0.05), the relatively large SEE values would preclude the use of BMI in predicting % fat or change in % fat with weight loss in bariatric surgery patients.

31 CFR 363.147 - How do I purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false How do I purchase a payroll zero... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.147 How do I purchase a payroll zero-percent...

31 CFR 363.147 - How do I purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false How do I purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.147 How do I purchase a payroll zero-percent...

31 CFR 363.147 - How do I purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false How do I purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.147 How do I purchase a payroll zero-percent...

31 CFR 363.147 - How do I purchase a payroll zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false How do I purchase a payroll zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Payroll Zero-Percent Certificate of Indebtedness § 363.147 How do I purchase a payroll zero-percent...

Nickel-hydrogen LEO cycling at 20-50 percent DOD. [depth of discharge

NASA Technical Reports Server (NTRS)

Lowery, John E.; Mai, Jenny

1991-01-01

Two NiH2 two-cell packs made up of engineering cells built according to the Hubble Space Telescope design (EPI RNH 90-3) are currently being low-earth-orbit (LEO) cycled at 20-50 percent depth of discharge (DOD). The cells were manufactured by Eagle-Picher Industries, Inc., and activated with electrolyte (KOH) concentrations of 26 percent (pack No.1) and 31 percent (pack No.2), for use during evaluation of the HST cell design. The cells have been grouped according to electrolyte concentration but follow the same test schedule for comparison. This test was set up to study the behavior of NiH2 cells having differing electrolyte concentrations, when operated at relatively high DOD (20-50 percent) in a LEO cycling program. The test was designed specifically to allow the cells to pick their own recharge ratio for varying DOD and varying EOC (end of charge) voltages. The cells are being cycled in a simulated 96-min orbit with 60-min charge and 36-min discharge where an EOC cutoff voltage controls high-rate charging. EOC cutoff voltages vary between 1.48 V and 1.56 V.

31 CFR 363.139 - May I transfer or deliver my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false May I transfer or deliver my zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.139 May I transfer or deliver my zero-percent certificate of indebtedness? A zero-percent...

31 CFR 363.139 - May I transfer or deliver my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false May I transfer or deliver my zero... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.139 May I transfer or deliver my zero-percent certificate of indebtedness? A zero-percent...

31 CFR 363.139 - May I transfer or deliver my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false May I transfer or deliver my zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.139 May I transfer or deliver my zero-percent certificate of indebtedness? A zero-percent...

31 CFR 363.139 - May I transfer or deliver my zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false May I transfer or deliver my zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.139 May I transfer or deliver my zero-percent certificate of indebtedness? A zero-percent...

WHK Student Internship Enrollment, Mentor Participation Up More than 50 Percent | Poster

Cancer.gov

By Nancy Parrish, Staff Writer The Werner H. Kirsten Student Internship Program (WHK SIP) has enrolled the largest class ever for the 2013–2014 academic year, with 66 students and 50 mentors. This enrollment reflects a 53 percent increase in students and a 56 percent increase in mentors, compared to 2012–2013 (43 students and 32 mentors), according to Julie Hartman, WHK SIP director.

WHK Student Internship Enrollment, Mentor Participation Up More than 50 Percent | Poster

Cancer.gov

By Nancy Parrish, Staff Writer The Werner H. Kirsten Student Internship Program (WHK SIP) has enrolled the largest class ever for the 2013–2014 academic year, with 66 students and 50 mentors. This enrollment reflects a 53 percent increase in students and a 56 percent increase in mentors, compared to 2012–2013 (43 students and 32 mentors), according to Julie Hartman, WHK SIP

29 CFR 794.127 - Exemption conditioned on making 75 percent of sales within the State.

Code of Federal Regulations, 2010 CFR

2010-07-01

... means that over 75 percent of the annual dollar volume of sales must be from sales to customers within the same State in which the enterprise is located. If 25 percent or more of its sales volume is from... 29 Labor 3 2010-07-01 2010-07-01 false Exemption conditioned on making 75 percent of sales within...

Recurrent laryngeal nerve reinnervation in children: Acoustic and endoscopic characteristics pre-intervention and post-intervention. A comparison of treatment options.

PubMed

Zur, Karen B; Carroll, Linda M

2015-12-01

To establish the benefit of ansa cervicalis-recurrent laryngeal nerve reinnervation (ANSA-RLN) for the management of dysphonia secondary to unilateral vocal cord paralysis (UVCP) in children. Children treated with ANSA-RLN for the management of dysphonia secondary to unilateral vocal fold immobility will have superior acoustic, perceptual, and stroboscopic outcomes compared to injection laryngoplasty and observation. Retrospective case-series chart review. Laryngeal, perceptual, and acoustic analysis of dysphonia was performed in 33 children (age 2-16 years) diagnosed with UVCP. Comparison of pre-post function for treatment groups (no treatment, injection laryngoplasty, ANSA-RLN) with additional comparison between gestational ages, age at initial evaluation, and gender were examined. Perceptual measures included Pediatric Voice Handicap Index (pVHI) and Grade, Roughness, Breathiness, Asthenia, Strain (GBRAS) perceptual rating. Objective measures included semitone (ST) range, jitter%, shimmer%, noise-to-harmonic ratio, voicing, and maximum phonation time. Post-treatment, pVHI, jitter%, and ST were significantly improved for ANSA-RLN subjects compared to injection subjects. Improved function (laryngeal diadochokinesis, pVHI, GRBAS, and/or acoustic) was observed in all ANSA-RLN subjects who had vocal fold paralysis as the only laryngeal diagnosis. This study presents one of the largest studies of pediatric vocal fold paralysis diagnosis and treatment. The study looks at the spectrum of function in patients with UVCP and looks at the outcomes of options: no treatment, injection laryngoplasty, and ANSA-RLN. Although surgical outcomes vary, both injection laryngoplasty and ANSA-RLN show benefit in laryngeal function, voice stability, voice capacity, perceptual rating, and pVHI scores. Both injection laryngoplasty and ANSA-RLN showed improvements post-treatment, and should be considered for management of pediatric UVCP. However, the ANSA-RLN group showed better and longer

64 Percent of Asian and Pacific Islander Treatment Admissions Name Alcohol as Their Problem

MedlinePlus

... 000 (1 percent) of the 1.8 million substance abuse admissions were APIs. Among all admissions, 60 percent ... AANHPI. aspx. Asian and Pacific Islander Admissions to Substance Abuse Treatment and Total Substance Abuse Treatment Admissions Reporting ...

Determinants of percent expenditure of household income due to childhood diarrhoea in rural Bangladesh.

PubMed

Das, J; Das, S K; Ahmed, S; Ferdous, F; Farzana, F D; Sarker, M H R; Ahmed, A M S; Chisti, M J; Malek, M A; Rahman, A; Faruque, A S G; Mamun, A A

2015-10-01

There is limited information on percent expenditure of household income due to childhood diarrhoea especially in rural Bangladesh. A total of 4205 children aged <5 years with acute diarrhoea were studied. Percent expenditure was calculated as total expenditure for the diarrhoeal episode divided by monthly family income, multiplied by 100. Overall median percent expenditure was 3·04 (range 0·01-94·35). For Vibrio cholerae it was 6·42 (range 0·52-82·85), for enterotoxigenic Escherichia coli 3·10 (range 0·22-91·87), for Shigella 3·17 (range 0·06-77·80), and for rotavirus 3·08 (range 0·06-48·00). In a multinomial logistic regression model, for the upper tertile of percent expenditure, significant higher odds were found for male sex, travelling a longer distance to reach hospital (⩾median of 4 miles), seeking care elsewhere before attending hospital, vomiting, higher frequency of purging (⩾10 times/day), some or severe dehydration and stunting. V. cholerae was the highest and rotavirus was the least responsible pathogen for percent expenditure of household income due to childhood diarrhoea.

Emirati Teachers' Perceptions of Voice Handicap.

PubMed

Natour, Yaser S; Sartawi, Abdealaziz M; Al Muhairy, Ousha; Efthymiou, Effie; Marie, Basem S

2016-05-01

The purpose of the study was to explore Emirati teachers' perceptions of voice handicap and to analyze their acoustic characteristics to determine whether acoustic measures of teachers' voice would verify their perceptions of voice handicap. Sixty-six Emirati school teachers (33 men and 33 women), with different years of teaching experience and age, and 100 control participants (50 men and 50 women) underwent vocal assessment that included the Voice Handicap Index (VHI-Arab) and acoustic measures (F0, jitter%, shimmer%, signal to noise ratio [SNR]). Significant differences between the teachers' group scores and the control group scores on the following subscales of VHI-Arab: physical (P = 0.006), emotional (P = 0.004), and total score of the test (P = 0.002). No significant differences were found among teachers in the three VHI subscales, and the total score regarding gender (functional P = 0.307; physical P = 0.341; emotional P = 0.126; and total P = 0.184), age (functional P = 0.972; physical P = 0.525; emotional P = 0.772; and total P = 0.848), and years of teaching experience (functional P = 0.319; physical P = 0.619; emotional P = 0.926; and total P = 0.638). The significant differences between the teacher's group and the control group in three acoustic measures: F0 (P = 0.000), shimmer% (P = 0.000), and SNR (P = 0.000) were further investigated. Significant differences were found among female and male teachers in F0 (P = 0.00) and SNR (P = 0.007). As for teachers' age, significant differences were found in SNR (P = 0.028). Teachers' years of experience did not show significant differences in any of the acoustic measures. Teachers have a higher perception of voice handicap. However, they were able to produce better voice quality than control participants were, as expressed in better SNRs. This might have been caused either by manipulation of vocal properties or abusive overloading the vocal system to produce a

Risk analysis of ODOT's HMA percent within limits (PWL) specification.

DOT National Transportation Integrated Search

2007-08-01

The Oklahoma Department of Transportation (ODOT) is considering switching its method of payment : for hot mix asphalt (HMA) construction from their current procedure to a Percent Within Limits (PWL) : specification. Quality characteristics are percen...

Identification of a novel percent mammographic density locus at 12q24.

PubMed

Stevens, Kristen N; Lindstrom, Sara; Scott, Christopher G; Thompson, Deborah; Sellers, Thomas A; Wang, Xianshu; Wang, Alice; Atkinson, Elizabeth; Rider, David N; Eckel-Passow, Jeanette E; Varghese, Jajini S; Audley, Tina; Brown, Judith; Leyland, Jean; Luben, Robert N; Warren, Ruth M L; Loos, Ruth J F; Wareham, Nicholas J; Li, Jingmei; Hall, Per; Liu, Jianjun; Eriksson, Louise; Czene, Kamila; Olson, Janet E; Pankratz, V Shane; Fredericksen, Zachary; Diasio, Robert B; Lee, Adam M; Heit, John A; DeAndrade, Mariza; Goode, Ellen L; Vierkant, Robert A; Cunningham, Julie M; Armasu, Sebastian M; Weinshilboum, Richard; Fridley, Brooke L; Batzler, Anthony; Ingle, James N; Boyd, Norman F; Paterson, Andrew D; Rommens, Johanna; Martin, Lisa J; Hopper, John L; Southey, Melissa C; Stone, Jennifer; Apicella, Carmel; Kraft, Peter; Hankinson, Susan E; Hazra, Aditi; Hunter, David J; Easton, Douglas F; Couch, Fergus J; Tamimi, Rulla M; Vachon, Celine M

2012-07-15

Percent mammographic density adjusted for age and body mass index (BMI) is one of the strongest risk factors for breast cancer and has a heritable component that remains largely unidentified. We performed a three-stage genome-wide association study (GWAS) of percent mammographic density to identify novel genetic loci associated with this trait. In stage 1, we combined three GWASs of percent density comprised of 1241 women from studies at the Mayo Clinic and identified the top 48 loci (99 single nucleotide polymorphisms). We attempted replication of these loci in 7018 women from seven additional studies (stage 2). The meta-analysis of stage 1 and 2 data identified a novel locus, rs1265507 on 12q24, associated with percent density, adjusting for age and BMI (P = 4.43 × 10(-8)). We refined the 12q24 locus with 459 additional variants (stage 3) in a combined analysis of all three stages (n = 10 377) and confirmed that rs1265507 has the strongest association in the 12q24 region (P = 1.03 × 10(-8)). Rs1265507 is located between the genes TBX5 and TBX3, which are members of the phylogenetically conserved T-box gene family and encode transcription factors involved in developmental regulation. Understanding the mechanism underlying this association will provide insight into the genetics of breast tissue composition.

Identification of a novel percent mammographic density locus at 12q24

PubMed Central

Stevens, Kristen N.; Lindstrom, Sara; Scott, Christopher G.; Thompson, Deborah; Sellers, Thomas A.; Wang, Xianshu; Wang, Alice; Atkinson, Elizabeth; Rider, David N.; Eckel-Passow, Jeanette E.; Varghese, Jajini S.; Audley, Tina; Brown, Judith; Leyland, Jean; Luben, Robert N.; Warren, Ruth M.L.; Loos, Ruth J.F.; Wareham, Nicholas J.; Li, Jingmei; Hall, Per; Liu, Jianjun; Eriksson, Louise; Czene, Kamila; Olson, Janet E.; Shane Pankratz, V.; Fredericksen, Zachary; Diasio, Robert B.; Lee, Adam M.; Heit, John A.; deAndrade, Mariza; Goode, Ellen L.; Vierkant, Robert A.; Cunningham, Julie M.; Armasu, Sebastian M.; Weinshilboum, Richard; Fridley, Brooke L.; Batzler, Anthony; Ingle, James N.; Boyd, Norman F.; Paterson, Andrew D.; Rommens, Johanna; Martin, Lisa J.; Hopper, John L.; Southey, Melissa C.; Stone, Jennifer; Apicella, Carmel; Kraft, Peter; Hankinson, Susan E.; Hazra, Aditi; Hunter, David J.; Easton, Douglas F.; Couch, Fergus J.; Tamimi, Rulla M.; Vachon, Celine M.

2012-01-01

Percent mammographic density adjusted for age and body mass index (BMI) is one of the strongest risk factors for breast cancer and has a heritable component that remains largely unidentified. We performed a three-stage genome-wide association study (GWAS) of percent mammographic density to identify novel genetic loci associated with this trait. In stage 1, we combined three GWASs of percent density comprised of 1241 women from studies at the Mayo Clinic and identified the top 48 loci (99 single nucleotide polymorphisms). We attempted replication of these loci in 7018 women from seven additional studies (stage 2). The meta-analysis of stage 1 and 2 data identified a novel locus, rs1265507 on 12q24, associated with percent density, adjusting for age and BMI (P = 4.43 × 10−8). We refined the 12q24 locus with 459 additional variants (stage 3) in a combined analysis of all three stages (n = 10 377) and confirmed that rs1265507 has the strongest association in the 12q24 region (P = 1.03 × 10−8). Rs1265507 is located between the genes TBX5 and TBX3, which are members of the phylogenetically conserved T-box gene family and encode transcription factors involved in developmental regulation. Understanding the mechanism underlying this association will provide insight into the genetics of breast tissue composition. PMID:22532574

SERIAL PERCENT-FREE PSA IN COMBINATION WITH PSA FOR POPULATION-BASED EARLY DETECTION OF PROSTATE CANCER

PubMed Central

Ankerst, Donna Pauler; Gelfond, Jonathan; Goros, Martin; Herrera, Jesus; Strobl, Andreas; Thompson, Ian M.; Hernandez, Javier; Leach, Robin J.

2016-01-01

PURPOSE To characterize the diagnostic properties of serial percent-free prostate-specific antigen (PSA) in relation to PSA in a multi-ethnic, multi-racial cohort of healthy men. MATERIALS AND METHODS 6,982 percent-free PSA and PSA measures were obtained from participants in a 12 year+ Texas screening study comprising 1625 men who never underwent biopsy, 497 who underwent one or more biopsies negative for prostate cancer, and 61 diagnosed with prostate cancer. Area underneath the receiver-operating-characteristic-curve (AUC) for percent-free PSA, and the proportion of patients with fluctuating values across multiple visits were determined according to two thresholds (under 15% versus 25%) were evaluated. The proportion of cancer cases where percent-free PSA indicated a positive test before PSA > 4 ng/mL did and the number of negative biopsies that would have been spared by percent-free PSA testing negative were computed. RESULTS Percent-free PSA fluctuated around its threshold of < 25% (< 15%) in 38.3% (78.1%), 42.2% (20.9%), and 11.4% (25.7%) of patients never biopsied, with negative and positive biopsies, respectively. At the same thresholds, percent-free PSA tested positive earlier than PSA in 71.4% (34.2%) of cancer cases, and among men with multiple negative biopsies and a PSA > 4 ng/mL, percent-free PSA would have tested negative in 31.6% (65.8%) instances. CONCLUSIONS Percent-free PSA should accompany PSA testing in order to potentially spare unnecessary biopsies or detect cancer earlier. When near the threshold, both tests should be repeated due to commonly observed fluctuation. PMID:26979652

31 CFR 363.132 - Can the sale of the zero-percent certificate of indebtedness be suspended?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false Can the sale of the zero-percent... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.132 Can the sale of the zero-percent certificate of indebtedness be suspended? The Secretary...

31 CFR 363.132 - Can the sale of the zero-percent certificate of indebtedness be suspended?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false Can the sale of the zero-percent... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.132 Can the sale of the zero-percent certificate of indebtedness be suspended? The Secretary...

31 CFR 363.132 - Can the sale of the zero-percent certificate of indebtedness be suspended?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false Can the sale of the zero-percent... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.132 Can the sale of the zero-percent certificate of indebtedness be suspended? The Secretary...

31 CFR 363.132 - Can the sale of the zero-percent certificate of indebtedness be suspended?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false Can the sale of the zero-percent... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.132 Can the sale of the zero-percent certificate of indebtedness be suspended? The Secretary...

A Comparison of Three Methods to Measure Percent Body Fat on Mentally Retarded Adults.

ERIC Educational Resources Information Center

Burkett, Lee N.; And Others

1994-01-01

Reports a study that compared three measures for determining percent body fat in mentally retarded adults (multiple skinfolds and circumference measurements, Infrared Interactance, and Bioelectrical Impedance). Results indicated the Bioelectrical Impedance Analyzer and Infrared Interactance Analyzer produced values for percent body fat that were…

Evaluating percent within limits (PWL) specifications volume 1 : HMA specifications.

DOT National Transportation Integrated Search

2006-05-01

The Oklahoma Department of Transportation (ODOT) has let four paving jobs for construction where : percent within limits (PWL) specifications were employed. The PWL specifications are intended to be : used as part of the Quality Assessment program to...

Characterizing noise in nonhuman vocalizations: Acoustic analysis and human perception of barks by coyotes and dogs

NASA Astrophysics Data System (ADS)

Riede, Tobias; Mitchell, Brian R.; Tokuda, Isao; Owren, Michael J.

2005-07-01

Measuring noise as a component of mammalian vocalizations is of interest because of its potential relevance to the communicative function. However, methods for characterizing and quantifying noise are less well established than methods applicable to harmonically structured aspects of signals. Using barks of coyotes and domestic dogs, we compared six acoustic measures and studied how they are related to human perception of noisiness. Measures of harmonic-to-noise-ratio (HNR), percent voicing, and shimmer were found to be the best predictors of perceptual rating by human listeners. Both acoustics and perception indicated that noisiness was similar across coyote and dog barks, but within each species there was significant variation among the individual vocalizers. The advantages and disadvantages of the various measures are discussed.

Acoustic characteristics of different target vowels during the laryngeal telescopy.

PubMed

Shu, Min-Tsan; Lee, Kuo-Shen; Chang, Chin-Wen; Hsieh, Li-Chun; Yang, Cheng-Chien

2014-10-01

The aim of this study was to investigate the acoustic characteristics of target vowels phonated in normal voice persons while performing laryngeal telescopy. The acoustic characteristics are compared to show the extent of possible difference to speculate their impact on phonation function. Thirty-four male subjects aged 20-39 years with normal voice were included in this study. The target vowels were /i/ and /ɛ/. Recording of voice samples was done under natural phonation and during laryngeal telescopy. The acoustic analysis included the parameters of fundamental frequency, jitter, shimmer and noise-to-harmonic ratio. The sound of a target vowel /ɛ/ was perceived identical in more than 90% of the subjects by the examiner and speech language pathologist during the telescopy. Both /i/ and /ɛ/ sounds showed significant difference when compared with the results under natural phonation. There was no significant difference between /i/ and /ɛ/ during the telescopy. The present study showed that change in target vowels during laryngeal telescopy makes no significant difference in the acoustic characteristics. The results may lead to the speculation that the phonation mechanism was not affected significantly by different vowels during the telescopy. This study may suggest that in the principle of comfortable phonation, introduction of the target vowels /i/ and /ɛ/ is practical. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Preliminary study of acoustic analysis for evaluating speech-aid oral prostheses: Characteristic dips in octave spectrum for comparison of nasality.

PubMed

Chang, Yen-Liang; Hung, Chao-Ho; Chen, Po-Yueh; Chen, Wei-Chang; Hung, Shih-Han

2015-10-01

Acoustic analysis is often used in speech evaluation but seldom for the evaluation of oral prostheses designed for reconstruction of surgical defect. This study aimed to introduce the application of acoustic analysis for patients with velopharyngeal insufficiency (VPI) due to oral surgery and rehabilitated with oral speech-aid prostheses. The pre- and postprosthetic rehabilitation acoustic features of sustained vowel sounds from two patients with VPI were analyzed and compared with the acoustic analysis software Praat. There were significant differences in the octave spectrum of sustained vowel speech sound between the pre- and postprosthetic rehabilitation. Acoustic measurements of sustained vowels for patients before and after prosthetic treatment showed no significant differences for all parameters of fundamental frequency, jitter, shimmer, noise-to-harmonics ratio, formant frequency, F1 bandwidth, and band energy difference. The decrease in objective nasality perceptions correlated very well with the decrease in dips of the spectra for the male patient with a higher speech bulb height. Acoustic analysis may be a potential technique for evaluating the functions of oral speech-aid prostheses, which eliminates dysfunctions due to the surgical defect and contributes to a high percentage of intelligible speech. Octave spectrum analysis may also be a valuable tool for detecting changes in nasality characteristics of the voice during prosthetic treatment of VPI. Copyright © 2014. Published by Elsevier B.V.

The effect of singing training on voice quality for people with quadriplegia.

PubMed

Tamplin, Jeanette; Baker, Felicity A; Buttifant, Mary; Berlowitz, David J

2014-01-01

Despite anecdotal reports of voice impairment in quadriplegia, the exact nature of these impairments is not well described in the literature. This article details objective and subjective voice assessments for people with quadriplegia at baseline and after a respiratory-targeted singing intervention. Randomized controlled trial. Twenty-four participants with quadriplegia were randomly assigned to a 12-week program of either a singing intervention or active music therapy control. Recordings of singing and speech were made at baseline, 6 weeks, 12 weeks, and 6 months postintervention. These deidentified recordings were used to measure sound pressure levels and assess voice quality using the Multidimensional Voice Profile and the Perceptual Voice Profile. Baseline voice quality data indicated deviation from normality in the areas of breathiness, strain, and roughness. A greater percentage of intervention participants moved toward more normal voice quality in terms of jitter, shimmer, and noise-to-harmonic ratio; however, the improvements failed to achieve statistical significance. Subjective and objective assessments of voice quality indicate that quadriplegia may have a detrimental effect on voice quality; in particular, causing a perception of roughness and breathiness in the voice. The results of this study suggest that singing training may have a role in ameliorating these voice impairments. Copyright © 2014 The Voice Foundation. Published by Mosby, Inc. All rights reserved.

Acoustic Analysis of Voice and Electroglottography in Patients With Laryngopharyngeal Reflux.

PubMed

Ramírez, Daphne Anahit Morales; Jiménez, Víctor Manuel Valadez; López, Xochiquetzal Hernández; Ysunza, Pablo Antonio

2018-05-01

Laryngopharyngeal reflux (LPR) refers to the flow of gastric acid content into the laryngopharynx. It has been reported that 10% of the patients consulting an otolaryngologist present with this condition. Signs of LPR can be identified during flexible or rigid laryngoscopy. The Voice Handicap Index (VHI) is a reliable tool for detecting the impact of voice disorders, and acoustic assessment of voice including acoustic analysis of voice (AAV) and electroglottography (EGG) provide objective data of voice production and voice disorders. This study aimed to describe changes in AAV, EGG, and VHI in patients who present with LPR compared with a matched control group of healthy subjects. Seventeen patients with LPR were studied. A group of healthy subjects matched by age and gender without any history of voice disorder, LPR, or gastroesophageal reflux disease was assembled. Both groups of patients were studied by VHI, flexible laryngoscopy, AAV, and EGG. All patients with LPR demonstrated abnormal VHI values. Shimmer, jitter, open quotient, and irregularity were significantly increased in the patients with LPR. Nonsignificant correlations were found between VHI scores and abnormal acoustic parameters in patients with LPR. Although abnormal acoustic parameters of patients with LPR were not predictive of the overall VHI score, the abnormal acoustic parameters of patients with LPR suggest a decrease in adequate laryngeal control during phonation. Copyright © 2018 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Effect of Performance Time of the Semi-Occluded Vocal Tract Exercises in Dysphonic Children.

PubMed

Ramos, Lorena de Almeida; Gama, Ana Cristina Côrtes

2017-05-01

This study aimed to verify the effects of execution time on auditory-perceptual and acoustic responses in children with dysphonia completing straw phonation exercises. A randomized, prospective, comparative intra-subject study design was used. Twenty-seven children, ranging from 5 to 10 years of age, diagnosed with vocal cord nodules or cysts, were enrolled in the study. All subjects included in the Experimental Group were also included in the Control Group which involved complete voice rest. Sustained vowels (/a/e/ε/e/) counting from 1 to 10 were recorded before the exercises (m0) and then again after the first (m1), third (m3), fifth (m5), and seventh (m7) minutes of straw phonation exercises. The recordings were randomized and presented to five speech therapists, who evaluated vocal quality based on the Grade Roughness Breathiness Asthenia/Strain Instability scale. For acoustic analysis, fundamental frequency, jitter, shimmer, glottal to noise excitation ratio, and noise parameters were analyzed. Reduced roughness, breathiness, and noise measurements as well as increased glottal to noise excitation ratio were observed in the Experimental Group after 3 minutes of exercise. Reduced grade of dysphonia and breathiness were noted after 5 minutes. The ideal duration of straw phonation in children with dysphonia is from 3 to 5 minutes. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Prolonged Exercise and Changes in Percent Fat Determinations by Hydrostatic Weighing and Scintillation Counting.

ERIC Educational Resources Information Center

Thomas, Tom R.; And Others

1979-01-01

This study, designed to determine the effect of a prolonged running bout on the measurement of percent fat, produced erroneously low readings. It is suggested that previous exercise and state of hydration of subjects should be controlled prior to percent fat determination by hydrostatic weighing or scintillation counting. (MJB)

The `I see you' prey-predator signal of Apis cerana is innate

NASA Astrophysics Data System (ADS)

Tan, Ken; Wang, Zhenwei; Chen, Weiweng; Hu, Zongwen; Oldroyd, Benjamin P.

2013-03-01

An `I see you' (ISY) prey-predator signal can co-evolve when such a signal benefits both prey and predator. The prey benefits if, by producing the signal, the predator is likely to break off an attack. The predator benefits if it is informed by the signal that the prey is aware of its presence and can break off what is likely to be an unsuccessful and potentially costly hunt. Because the signal and response co-evolve in two species, the behaviour underlying an ISY signal is expected to have a strong genetic component and cannot be entirely learned. An example of an ISY signal is the `shimmering' behaviour performed by Asian hive bee workers in the presence of their predator Vespa velutina. To test the prediction that bee-hornet signalling is heritable, we let honey bee workers of two species emerge in an incubator so that they had never been exposed to V. velutina. In Apis cerana, the shimmering response developed 48 h post-emergence, was strong after 72 h and increased further over 2 weeks. In contrast, A. mellifera, which has evolved in the absence of Asian hornets, did not produce the shimmering signal. In control tests, A. cerana workers exposed to a non-threatening butterfly did not respond with the shimmering signal.

35 GHz integrated circuit rectifying antenna with 33 percent efficiency

NASA Technical Reports Server (NTRS)

Yoo, T.-W.; Chang, K.

1991-01-01

A 35 GHz integrated circuit rectifying antenna (rectenna) has been developed using a microstrip dipole antenna and beam-lead mixer diode. Greater than 33 percent conversion efficiency has been achieved. The circuit should have applications in microwave/millimeter-wave power transmission and detection.

31 CFR 363.145 - May I delete a pending transaction involving a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... involving a zero-percent certificate of indebtedness? 363.145 Section 363.145 Money and Finance: Treasury... PUBLIC DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.145 May I delete a pending transaction involving a...

31 CFR 363.145 - May I delete a pending transaction involving a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... involving a zero-percent certificate of indebtedness? 363.145 Section 363.145 Money and Finance: Treasury... PUBLIC DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.145 May I delete a pending transaction involving a...

31 CFR 363.145 - May I delete a pending transaction involving a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... involving a zero-percent certificate of indebtedness? 363.145 Section 363.145 Money and Finance: Treasury... FISCAL SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.145 May I delete a pending transaction involving a...

31 CFR 363.145 - May I delete a pending transaction involving a zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... involving a zero-percent certificate of indebtedness? 363.145 Section 363.145 Money and Finance: Treasury... PUBLIC DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.145 May I delete a pending transaction involving a...

Use of a Passive Reaction Wheel Jitter Isolation System to Meet the Advanced X-Ray Astrophysics Facility Imaging Performance Requirements

NASA Technical Reports Server (NTRS)

Pendergast, Karl J.; Schauwecker, Christopher J.

1998-01-01

Third in the series of NASA great observatories, the Advanced X-Ray Astrophysics Facility (AXAF) is scheduled for launch from the Space Shuttle in November of 1998. Following in the path of the Hubble Space Telescope and the Compton Gamma Ray Observatory, this observatory will image light at X-ray wavelengths, facilitating the detailed study of such phenomena as supernovae and quasars. The AXAF project is sponsored by the Marshall Space Flight Center in Huntsville, Alabama. Because of exacting requirements on the performance of the AXAF optical system, it was necessary to reduce the transmission of reaction wheel jitter disturbances to the observatory. This reduction was accomplished via use of a passive mechanical isolation system to interface the reaction wheels with the spacecraft central structure. In addition to presenting a description of the spacecraft, the isolation system, and the key image quality requirement flowdown, this paper details the analyses performed in support of system-level imaging performance requirement verification. These analyses include the identification of system-level requirement suballocations, quantification of imaging and pointing performance, and formulation of unit-level isolation system transmissibility requirements. Given in comparison to the non-isolated system imaging performance, the results of these analyses clearly illustrate the effectiveness of an innovative reaction wheel passive isolation system.

Study of extraterrestrial disposal of radioactive wastes. Part 3: Preliminary feasibility screening study of space disposal of the actinide radioactive wastes with 1 percent and 0.1 percent fission product contamination

NASA Technical Reports Server (NTRS)

Hyland, R. E.; Wohl, M. L.; Finnegan, P. M.

1973-01-01

A preliminary study was conducted of the feasibility of space disposal of the actinide class of radioactive waste material. This waste was assumed to contain 1 and 0.1 percent residual fission products, since it may not be feasible to completely separate the actinides. The actinides are a small fraction of the total waste but they remain radioactive much longer than the other wastes and must be isolated from human encounter for tens of thousands of years. Results indicate that space disposal is promising but more study is required, particularly in the area of safety. The minimum cost of space transportation would increase the consumer electric utility bill by the order of 1 percent for earth escape and 3 percent for solar escape. The waste package in this phase of the study was designed for normal operating conditions only; the design of next phase of the study will include provisions for accident safety. The number of shuttle launches per year required to dispose of all U.S. generated actinide waste with 0.1 percent residual fission products varies between 3 and 15 in 1985 and between 25 and 110 by 2000. The lower values assume earth escape (solar orbit) and the higher values are for escape from the solar system.

18 Percent of Pregnant Women Drink Alcohol during Early Pregnancy

MedlinePlus

National Survey on Drug Use and Health The NSDUH Report Data Spotlight September 9, 2013 18 Percent of Pregnant VA60 Women Drink Alcohol during Early Pregnancy Women who drink alcohol while pregnant increase the risk that their infants will have physical, learning, and/ ...

46 CFR 42.20-7 - Flooding standard: Type “B” vessel, 60 percent reduction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Flooding standard: Type âBâ vessel, 60 percent reduction... DOMESTIC AND FOREIGN VOYAGES BY SEA Freeboards § 42.20-7 Flooding standard: Type “B” vessel, 60 percent... applied to the following flooding standards: (1) If the vessel is 225 meters (738 feet) or less in length...

46 CFR 42.20-7 - Flooding standard: Type “B” vessel, 60 percent reduction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Flooding standard: Type âBâ vessel, 60 percent reduction... DOMESTIC AND FOREIGN VOYAGES BY SEA Freeboards § 42.20-7 Flooding standard: Type “B” vessel, 60 percent... applied to the following flooding standards: (1) If the vessel is 225 meters (738 feet) or less in length...

46 CFR 42.20-7 - Flooding standard: Type “B” vessel, 60 percent reduction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Flooding standard: Type âBâ vessel, 60 percent reduction... DOMESTIC AND FOREIGN VOYAGES BY SEA Freeboards § 42.20-7 Flooding standard: Type “B” vessel, 60 percent... applied to the following flooding standards: (1) If the vessel is 225 meters (738 feet) or less in length...

29 CFR 553.212 - Twenty percent limitation on nonexempt work.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Twenty percent limitation on nonexempt work. (a) Employees engaged in fire protection or law enforcement... example, firefighters who work for forest conservation agencies may, during slack times, plant trees and... of the total hours worked by that employee during the workweek or applicable work period. A person...

31 CFR 363.140 - May a zero-percent certificate of indebtedness be pledged or used as collateral?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false May a zero-percent certificate of... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.140 May a zero-percent certificate of indebtedness be pledged or used as collateral? A zero...

31 CFR 363.140 - May a zero-percent certificate of indebtedness be pledged or used as collateral?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false May a zero-percent certificate of... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.140 May a zero-percent certificate of indebtedness be pledged or used as collateral? A zero...

31 CFR 363.140 - May a zero-percent certificate of indebtedness be pledged or used as collateral?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false May a zero-percent certificate of... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.140 May a zero-percent certificate of indebtedness be pledged or used as collateral? A zero...

31 CFR 363.140 - May a zero-percent certificate of indebtedness be pledged or used as collateral?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false May a zero-percent certificate of... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.140 May a zero-percent certificate of indebtedness be pledged or used as collateral? A zero...

Effect of simultaneous variation in temperature and ammonia concentration on percent fertilization and hatching in Crassostrea ariakensis.

PubMed

Hui, Wang; Jiahui, Liu; Hongshuai, Yang; Jin, Liu; Zhigang, Liu

2014-04-01

The combined effects of temperature and ammonia concentration on the percent fertilization and percent hatching in Crassostrea ariakensis were examined under laboratory conditions using the central composite design and response surface methodology. The results indicated: (1) The linear effects of temperature and ammonia concentration on the percent fertilization were significant (P<0.05), and the quadratic effects were highly significant (P<0.01). The interactive effect between temperature and ammonia concentration on the percent fertilization was not significant (P>0.05). (2) The linear effect of temperature on the percent hatching was highly significant (P<0.01), and that of ammonia concentration was nonsignificant (P>0.05). The quadratic effects of temperature and ammonia concentration on the percent hatching were highly significant (P<0.01). The interaction on the percent hatching was not significant (P>0.05). Temperature was more important than ammonia in influencing the fertilization and hatching in C. ariakensis. (3) The model equations of the percent fertilization and hatching towards temperature and ammonia concentration were established, with the coefficients of determination R(2)=99.4% and 99.76%, respectively. Through the lack-of-fit test, these models were of great adequacy. The predictive coefficients of determination for the two model equations were as high as 94.6% and 98.03%, respectively, showing that they could be used for practical projection. (4) Via the statistical simultaneous optimization technique, the optimal factor level combination, i.e., 25°C/0.038mgmL(-1), was derived, at which the greatest percent fertilization 95.25% and hatching 83.26% was achieved, with the desirability being 97.81%. Our results may provide advantageous guidelines for the successful reproduction of C. ariakensis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Hot press and roll welding of titanium-6-percent-aluminum-4-percent-vanadium bar and sheet with auto-vacuum cleaning

NASA Technical Reports Server (NTRS)

Holko, K. H.

1972-01-01

Hot press butt welds were made in 0.5 in. diameter bar, and roll lap welds were made in 0.060 in. thick sheet of Ti-6A1-4V. For hot press welds made after auto-vacuum cleaning at 1800 F for 2 hours, weld strength and ductility equaled the parent metal properties. Only 5 minutes of pressing time were needed at 1800 F and 200 psi to make the hot press welds. Roll welds were made in sheet at 1750 F with only 10 percent deformation. The welds in the bar and sheet were metallurgically indistinguishable from the parent material.

Percent Grammatical Responses as a General Outcome Measure: Initial Validity

ERIC Educational Resources Information Center

Eisenberg, Sarita L.; Guo, Ling-Yu

2018-01-01

Purpose: This report investigated the validity of using percent grammatical responses (PGR) as a measure for assessing grammaticality. To establish construct validity, we computed the correlation of PGR with another measure of grammar skills and with an unrelated skill area. To establish concurrent validity for PGR, we computed the correlation of…

Photometry from space

NASA Technical Reports Server (NTRS)

Nelson, M. J.; Bless, R. C.; Percival, J. W.; White, R. L.

1992-01-01

A brief description of the High Speed Photometer (HSP) of the Hubble Space Telescope is given, in particular the HSP light path, detectors, entrance apertures, and filters. The status of HSP testing to date is reported, and problems encountered with the bright earth and the telescope pointing system are described. The calibration effort for the HSP is well under way. Results of internal (instrument coordinate) aperture locations good to 0.05 arcsec and external (telescope coordinate) locations good to 0.02 arcsec are shown. The effects of spacecraft pointing and jitter on HSP photometry are detailed, and a preliminary measurement of spacecraft jitter with HSP is shown. The aperture calibration effort is verified by accurate pointing of a star to different HSP 1.0 arcsec entrance apertures, and photometric performance of the instrument is shown to be accurate to the 2 percent photon noise of the observations. Future science verification and guaranteed observing time programs are listed. Suggestions are made for future space-based photometers.

Evaluating Equating Results: Percent Relative Error for Chained Kernel Equating

ERIC Educational Resources Information Center

Jiang, Yanlin; von Davier, Alina A.; Chen, Haiwen

2012-01-01

This article presents a method for evaluating equating results. Within the kernel equating framework, the percent relative error (PRE) for chained equipercentile equating was computed under the nonequivalent groups with anchor test (NEAT) design. The method was applied to two data sets to obtain the PRE, which can be used to measure equating…

31 CFR 363.131 - What is a TreasuryDirect ® zero-percent certificate of indebtedness?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 31 Money and Finance:Treasury 2 2012-07-01 2012-07-01 false What is a TreasuryDirect ® zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.131 What is a TreasuryDirect ® zero-percent certificate of indebtedness? A TreasuryDirect...

31 CFR 363.131 - What is a TreasuryDirect ® zero-percent certificate of indebtedness?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 31 Money and Finance:Treasury 2 2011-07-01 2011-07-01 false What is a TreasuryDirect ® zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.131 What is a TreasuryDirect ® zero-percent certificate of indebtedness? A TreasuryDirect...

31 CFR 363.131 - What is a TreasuryDirect ® zero-percent certificate of indebtedness?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 31 Money and Finance:Treasury 2 2013-07-01 2013-07-01 false What is a TreasuryDirect ® zero... DEBT REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.131 What is a TreasuryDirect ® zero-percent certificate of indebtedness? A TreasuryDirect...

31 CFR 363.131 - What is a TreasuryDirect ® zero-percent certificate of indebtedness?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 31 Money and Finance: Treasury 2 2014-07-01 2014-07-01 false What is a TreasuryDirect ® zero... SERVICE REGULATIONS GOVERNING SECURITIES HELD IN TREASURYDIRECT Zero-Percent Certificate of Indebtedness General § 363.131 What is a TreasuryDirect ® zero-percent certificate of indebtedness? A TreasuryDirect...

National Health Expenditure Projections, 2016-25: Price Increases, Aging Push Sector To 20 Percent Of Economy.

PubMed

Keehan, Sean P; Stone, Devin A; Poisal, John A; Cuckler, Gigi A; Sisko, Andrea M; Smith, Sheila D; Madison, Andrew J; Wolfe, Christian J; Lizonitz, Joseph M

2017-03-01

Under current law, national health expenditures are projected to grow at an average annual rate of 5.6 percent for 2016-25 and represent 19.9 percent of gross domestic product by 2025. For 2016, national health expenditure growth is anticipated to have slowed 1.1 percentage points to 4.8 percent, as a result of slower Medicaid and prescription drug spending growth. For the rest of the projection period, faster projected growth in medical prices is partly offset by slower projected growth in the use and intensity of medical goods and services, relative to that observed in 2014-16 associated with the Affordable Care Act coverage expansions. The insured share of the population is projected to increase from 90.9 percent in 2015 to 91.5 percent by 2025. Project HOPE—The People-to-People Health Foundation, Inc.

Tensile and fatigue data for irradiated and unirradiated AISI 310 stainless steel and titanium - 5 percent aluminum - 2.5 percent tin: Application of the method of universal slopes

NASA Technical Reports Server (NTRS)

Debogdan, C. E.

1973-01-01

Irradiated and unirradiated tensile and fatigue specimens of AISI 310 stainless steel and Ti-5Al-2.5Sn were tested in the range of 100 to 10,000 cycles to failure to determine the applicability of the method of universal slopes to irradiated materials. Tensile data for both materials showed a decrease in ductility and increase in ultimate tensile strength due to irradiation. Irradiation caused a maximum change in fatigue life of only 15 to 20 percent for both materials. The method of universal slopes predicted all the fatigue data for the 310 SS (irradiated as well as unirradiated) within a life factor of 2. For the titanium alloy, 95 percent of the data was predicted within a life factor of 3.

Assessment of 2001 NLCD percent tree and impervious cover estimates

Treesearch

Eric Greenfield; David J. Nowak; Jeffrey T. Walton

2009-01-01

The 2001 National Land Cover Database (NLCD) tree and impervious cover maps provide an opportunity to extract basic land-cover information helpful for natural resource assessments. To determine the potential utility and limitations of the 2001 NLCD data, this exploratory study compared 2001 NLCD-derived values of overall percent tree and impervious cover within...

7 CFR 205.303 - Packaged products labeled “100 percent organic” or “organic.”

Code of Federal Regulations, 2011 CFR

2011-01-01

... Information § 205.303 Packaged products labeled “100 percent organic” or “organic.” (a) Agricultural products... product, the following: (1) The term, “100 percent organic” or “organic,” as applicable, to modify the name of the product; (2) For products labeled “organic,” the percentage of organic ingredients in the...

13 CFR 107.1410 - Requirement to redeem 4 percent Preferred Securities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Requirement to redeem 4 percent Preferred Securities. 107.1410 Section 107.1410 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS INVESTMENT COMPANIES SBA Financial Assistance for Licensees (Leverage) Preferred...

13 CFR 107.1420 - Articles requirements for 4 percent Preferred Securities.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Articles requirements for 4 percent Preferred Securities. 107.1420 Section 107.1420 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION SMALL BUSINESS INVESTMENT COMPANIES SBA Financial Assistance for Licensees (Leverage) Preferred...

Sap volume flow as influenced by tubing diameter and slope percent

Treesearch

H. Clay Smith

1971-01-01

The amount of sugar maple sap that can move through plastic tubing is controlled by several factors. The most important are tubing diameter and slope percent. Estimates are given of the number of tapholes that can be used with combinations of these variables.

31 CFR 363.143 - How do I purchase a security using the redemption proceeds of my zero-percent certificate of...

Code of Federal Regulations, 2014 CFR

2014-07-01

... the redemption proceeds of my zero-percent certificate of indebtedness? 363.143 Section 363.143 Money... Zero-Percent Certificate of Indebtedness Zero-Percent Certificate of Indebtedness § 363.143 How do I purchase a security using the redemption proceeds of my zero-percent certificate of indebtedness? You may...

An analysis of carrier phase jitter in an MPSK receiver utilizing map estimation. Ph.D. Thesis Semiannual Status Report, Jul. 1993 - Jan. 1994

NASA Technical Reports Server (NTRS)

Osborne, William P.

1994-01-01

The use of 8 and 16 PSK TCM to support satellite communications in an effort to achieve more bandwidth efficiency in a power-limited channel has been proposed. This project addresses the problem of carrier phase jitter in an M-PSK receiver utilizing the high SNR approximation to the maximum aposteriori estimation of carrier phase. In particular, numerical solutions to the 8 and 16 PSK self-noise and phase detector gain in the carrier tracking loop are presented. The effect of changing SNR on the loop noise bandwidth is also discussed. These data are then used to compute variance of phase error as a function of SNR. Simulation and hardware data are used to verify these calculations. The results show that there is a threshold in the variance of phase error versus SNR curves that is a strong function of SNR and a weak function of loop bandwidth. The M-PSK variance thresholds occur at SNR's in the range of practical interest for the use of 8 and 16-PSK TCM. This suggests that phase error variance is an important consideration in the design of these systems.

Safety Is 99 Percent Attitude: Strategies to Contain Workers' Compensation Costs.

ERIC Educational Resources Information Center

Parnell, Janet

1993-01-01

The University of Denver (Colorado) reduced workers' compensation losses 97 percent in 1990-91 by developing a master safety plan, sponsoring safety training, managing medical costs, providing modified duty for injured employees, screening applicants, orienting new employees, investigating claims thoroughly, performing life-safety audits, and…

Evaluation of EA-934NA with 2.5 percent Cab-O-Sil

NASA Technical Reports Server (NTRS)

Caldwell, Gordon A.

1990-01-01

Currently, Hysol adhesive EA-934NA is used to bond the Field Joint Protection System on the Shuttle rocket motors at Kennedy Space Center. However, due to processing problems, an adhesive with a higher viscosity is needed to alleviate these difficulties. One possible solution is to add Cab-O-Sil to the current adhesive. The adhesive strength and bond strengths that can be obtained when 2.5 percent Cab-O-Sil is added to adhesive EA-934NA are examined and tested over a range of test temperatures from -20 to 300 F. Tensile adhesion button and lap shear specimens were bonded to D6AC steel and uniaxial tensile specimens (testing for strength, initial tangent modulus, elongation and Poisson's ratio) were prepared using Hysol adhesive EA-934NA with 2.5 percent Cab-O-Sil added. These specimens were tested at -20, 20, 75, 100, 125, 150, 200, 250, and 300 F, respectively. Additional tensile adhesion button specimens bonding Rust-Oleum primed and painted D6AC steel to itself and to cork using adhesive EA-934NA with 2.5 percent Cab-O-Sil added were tested at 20, 75, 125, 200, and 300 F, respectively. Results generally show decreasing strength values with increasing test temperatures. The bond strengths obtained using cork as a substrate were totally dependent on the cohesive strength of the cork.

Effects of covert subject actions on percent body fat by air-displacement plethsymography.

PubMed

Tegenkamp, Michelle H; Clark, R Randall; Schoeller, Dale A; Landry, Greg L

2011-07-01

Air-displacement plethysmography (ADP) is used for estimation of body composition, however, some individuals, such as athletes in weight classification sports, may use covert methods during ADP testing to alter their apparent percent body fat. The purpose of this study was to examine the effect of covert subject actions on percent body fat measured by ADP. Subjects underwent body composition analysis in the Bod Pod following the standard procedure using the manufacturer's guidelines. The subjects then underwent 8 more measurements while performing the following intentional manipulations: 4 breathing patterns altering lung volume, foot movement to disrupt air, hand cupping to trap air, and heat and cold exposure before entering the chamber. Increasing and decreasing lung volume during thoracic volume measurement and during body density measurement altered the percent body fat assessment (p < 0.001). High lung volume during thoracic gas measures overestimated fat by 3.7 ± 2.1 percentage points. Lowered lung volume during body volume measures overestimated body fat by an additional 2.2 ± 2.1 percentage points. The heat and cold exposure, tapping, and cupping treatments provided similar estimates of percent body fat when compared with the standard condition. These results demonstrate the subjects were able to covertly change their estimated ADP body composition value by altering breathing when compared with the standard condition. We recommend that sports conditioning coaches, athletic trainers, and technicians administering ADP should be aware of the potential effects of these covert actions. The individual responsible for administering ADP should remain vigilant during testing to detect deliberate altered breathing patterns by athletes in an effort to gain a competitive advantage by manipulating their body composition assessment.

Lingering Effects of Straw Phonation Exercises on Aerodynamic, Electroglottographic, and Acoustic Parameters.

PubMed

Kang, Jing; Xue, Chao; Piotrowski, David; Gong, Ting; Zhang, Yi; Jiang, Jack J

2018-06-01

This study aimed to investigate the duration of straw phonation effects using aerodynamic, electroglottographic, and acoustic metrics. Twenty-four participants were recruited to perform both a 5-minute and a 10-minute straw phonation exercise. Upon completion of the exercises, phonation threshold pressure (PTP), mean airflow, contact quotient, fundamental frequency, jitter, shimmer, and noise-to-harmonics ratio were measured over a 20-minute time frame. Parameters were measured before the intervention (baseline), immediately after the intervention (m0), 5 minutes (m5), 10 minutes (m10), 15 minutes (m15), and 20 minutes (m20) after the intervention. PTP significantly decreased immediately after 5 minutes of straw phonation and returned to initial state within 5 minutes. PTP remained decreased over 5 minutes after 10 minutes of straw phonation. Mean airflow increased immediately after both 5 minutes and 10 minutes of straw phonations and remained improved for 20 minutes. No significant changes were obtained for contact quotient and acoustic parameters over the intervention period. The results extended our knowledge of proper clinical application of straw phonation regarding the duration of exercise. This study confirmed that 10 minutes of straw phonation lead to optimal and relatively continuous effects in PTP and mean airflow. Although straw phonation did show lingering effects in aerodynamics, repeated practices were recommended to obtain optimum and therapeutic effects. Copyright © 2018 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Office-based treatment of vocal fold polyp with flexible laryngosvideostroboscopic surgery.

PubMed

Lan, Ming-Chin; Hsu, Yen-Bin; Chang, Shyue-Yih; Huang, Jui-Lin; Tai, Shyh-Kuan; Chien, Chih-Hung; Chu, Pen-Yuan

2010-02-01

To evaluate the usefulness and safety of flexible laryngovideostroboscopic (FLVS) surgery in patients with vocal fold polyp and to discuss its advantages and limitations in comparison with traditional direct microlaryngoscopic technique under general anesthesia. Retrospective analysis. Twenty patients with vocal fold polyp treated by FLVS surgery under topical anesthesia were reviewed. The results were evaluated by videostroboscopy and grade of the severity of dysphonia, roughness, and breathiness (GRB) scales. Phonatory results, including maximum phonation time, jitter, shimmer, and noise to harmonic ratio, were also reviewed for objective evaluations. All patients completed the surgery smoothly, and seven of them had a higher risk for general anesthesia because of their medical diseases. The procedure was typically accomplished within 20 minutes, and no complications were noted. Videostroboscopy showed improved degree of glottic closure (p < .001), regularity (p = .046), phase symmetry (p = .008), and mucosal wave (p = .008) after FLVS. A significant improvement was noted between preoperative and postoperative results with regard to GRB scale (p < .001, p = .001, and p = .013, respectively). Maximum phonation time also increased significantly after surgery (p = .002). Trivial mucosal residual was noted in one patient. No recurrence was found after a 6-month follow-up period. FLVS surgery is a highly applicable procedure with low invasiveness and minimal morbidity. It offers a simple and cost-effective alternative to the traditional direct microlaryngoscopic procedure, especially for those who are not candidates for general anesthesia or suspension of the larynx.

Long-term voice handicap index after type II thyroplasty using titanium bridges for adductor spasmodic dysphonia.

PubMed

Sanuki, Tetsuji; Yumoto, Eiji; Kodama, Narihiro; Minoda, Ryosei; Kumai, Yoshihiko

2014-06-01

To determine the long-term functional outcomes of type II thyroplasty using titanium bridges for adductor spasmodic dysphonia (AdSD) by perceptual analysis using the Voice Handicap Index-10 (VHI-10) and by acoustic analysis. Fifteen patients with AdSD underwent type II thyroplasty using titanium brides between August 2006 and February 2011. VHI-10 scores, a patient-based survey that quantifies a patient's perception of his or her vocal handicap, were determined before and at least 2 years after surgery. Concurrent with the VHI-10 evaluation, acoustic parameters were assessed, including jitter, shimmer, harmonic-to-noise ratio (HNR), standard deviation of F0 (SDF0), and degree of voice breaks (DVB). The average follow-up interval was 30.1 months. No patient had strangulation of the voice, and all were satisfied with the voice postoperatively. In the perceptual analysis, the mean VHI-10 score improved significantly, from 26.7 to 4.1 two years after surgery. All patients had significantly improved each score of three different aspects of VHI-10, representing improved functional, physical, and emotional well-being. All acoustic parameters improved significantly 2 years after surgery. The treatment of AdSD with type II thyroplasty significantly improved the voice-related quality of life and acoustic parameters 2 years after surgery. The results of the study suggest that type II thyroplasty using titanium bridges provides long-term relief of vocal symptoms in patients with AdSD. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

The effect of age of cochlear implantation on vocal characteristics in children.

PubMed

Knight, Kerry; Ducasse, Simone; Coetzee, Ashley; van der Linde, Jeannie; Louw, Anel

2016-06-27

Early cochlear implantation aids auditory feedback and supports better communication and self-monitoring of the voice. The objective of this study was to determine whether the age of cochlear implantation has an impact on vocal development in children implanted before age 4. The study consisted of 19 participants in total. All implant recipients (experimental group) were 3-5 years post-implantation, including four prelingual (0-2 years) and five perilingual (2-4 years) implant recipients. The control group consisted of 10 children whose hearing was within normal limits between the ages 3-6 years and 10 months, which was compared to the experimental group. Established paediatric norms were used for additional comparison. A questionnaire was used to gather information from each of the participant's caregivers to determine whether other personal and contextual factors had an impact on voice production. An acoustic analysis was conducted for each participant using the Multi-Dimensional Voice Program of the Computerized Speech Lab. When the experimental group and the control group were compared, similar results were yielded for fundamental frequency and short-term perturbation (jitter and shimmer). More variability was noted in long-term frequency and amplitude measures, with significantly higher differences, and therefore further outside the norms, in the prelingual group when compared to the perilingual and control groups. In this study, age of implantation did not impact vocal characteristics. Further research should include larger sample sizes, with participants that are age and gender matched.

Cochlear implanted children present vocal parameters within normal standards.

PubMed

de Souza, Lourdes Bernadete Rocha; Bevilacqua, Maria Cecília; Brasolotto, Alcione Ghedini; Coelho, Ana Cristina

2012-08-01

to compare acoustic and perceptual parameters regarding the voice of cochlear implanted children, with normal hearing children. this is a cross-sectional, quantitative and qualitative study. Thirty six cochlear implanted children aged between 3 y and 3 m to 5 y and 9 m and 25 children with normal hearing, aged between 3 y and 11 m and 6 y and 6 m, participated in this study. The recordings and the acoustics analysis of the sustained vowel/a/and spontaneous speech were performed using the PRAAT program. The parameters analyzed for the sustained vowel were the mean of the fundamental frequency, jitter, shimmer and harmonic-to-noise ratio (HNR). For the spontaneous speech, the minimum and maximum frequencies and the number of semitones were extracted. The perceptual analysis of the speech material was analyzed using visual-analogical scales of 100 points, composing the aspects related to the overall severity of the vocal deviation, roughness, breathiness, strain, pitch, loudness and resonance deviation, and instability. This last parameter was only analyzed for the sustained vowel. The results demonstrated that the majority of the vocal parameters analyzed in the samples of the implanted children disclosed values similar to those obtained by the group of children with normal hearing. implanted children who participate in a (re) habilitation and follow-up program, can present vocal characteristics similar to those vocal characteristics of children with normal hearing. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Efficient, frequency-stable laser-diode-pumped Nd:YAG laser

NASA Technical Reports Server (NTRS)

Zhou, B.; Kane, T. J.; Dixon, G. J.; Byer, R. L.

1985-01-01

One of the main goals of the study was to demonstrate a low-power efficient Nd:YAG laser oscillator for applications in remote coherent Doppler anemometry. An electrical-to-optical slope efficiency of 6.5 percent has been achieved by using commercially available CW laser diodes of up to 100 mW to pump monolithic Nd:YAG rod lasers. The observed Nd:YAG oscillation threshold is at 2.3 mW of laser-diode output power, i.e., a small fraction of the rated output power. The highest Nd:YAG CW output power reached is 4.4 mW at an overall electrical-to-optical efficiency of 1.5 percent. The frequency jitter is less than 10 kHz in 0.3 s.

40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

40 CFR 60.1445 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1445 Section 60.1445 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1445 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If your air curtain incinerator combusts...

Individualized Math Problems in Percent. Oregon Vo-Tech Mathematics Problem Sets.

ERIC Educational Resources Information Center

Cosler, Norma, Ed.

This is one of eighteen sets of individualized mathematics problems developed by the Oregon Vo-Tech Math Project. Each of these problem packages is organized around a mathematical topic and contains problems related to diverse vocations. Solutions are provided for all problems. This volume includes problems concerned with computing percents.…

40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15380 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15380 Section 62.15380 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15380 How must I monitor opacity for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

40 CFR 62.15375 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 62.15375 Section 62.15375 Protection of Environment... Combustion Units Constructed on or Before August 30, 1999 Air Curtain Incinerators That Burn 100 Percent Yard Waste § 62.15375 What are the emission limits for air curtain incinerators that burn 100 percent yard...

40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

40 CFR 60.1920 - What are the emission limits for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1920 Section 60.1920 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1920 What are the emission limits for air curtain incinerators that burn 100 percent yard waste? If...

Verification of the Solar Dynamics Observatory High Gain Antenna Pointing Algorithm Using Flight Data

NASA Technical Reports Server (NTRS)

Bourkland, Kristin L.; Liu, Kuo-Chia

2011-01-01

The Solar Dynamics Observatory (SDO), launched in 2010, is a NASA-designed spacecraft built to study the Sun. SDO has tight pointing requirements and instruments that are sensitive to spacecraft jitter. Two High Gain Antennas (HGAs) are used to continuously send science data to a dedicated ground station. Preflight analysis showed that jitter resulting from motion of the HGAs was a cause for concern. Three jitter mitigation techniques were developed and implemented to overcome effects of jitter from different sources. These mitigation techniques include: the random step delay, stagger stepping, and the No Step Request (NSR). During the commissioning phase of the mission, a jitter test was performed onboard the spacecraft, in which various sources of jitter were examined to determine their level of effect on the instruments. During the HGA portion of the test, the jitter amplitudes from the single step of a gimbal were examined, as well as the amplitudes due to the execution of various gimbal rates. The jitter levels were compared with the gimbal jitter allocations for each instrument. The decision was made to consider implementing two of the jitter mitigating techniques on board the spacecraft: stagger stepping and the NSR. Flight data with and without jitter mitigation enabled was examined, and it is shown in this paper that HGA tracking is not negatively impacted with the addition of the jitter mitigation techniques. Additionally, the individual gimbal steps were examined, and it was confirmed that the stagger stepping and NSRs worked as designed. An Image Quality Test was performed to determine the amount of cumulative jitter from the reaction wheels, HGAs, and instruments during various combinations of typical operations. The HGA-induced jitter on the instruments is well within the jitter requirement when the stagger step and NSR mitigation options are enabled.

40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2012 CFR

2012-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2010 CFR

2010-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

40 CFR 60.1925 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2011 CFR

2011-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1925 Section 60.1925 Protection of Environment... or Before August 30, 1999 Model Rule-Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1925 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use...

40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2014 CFR

2014-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

40 CFR 60.1450 - How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste?

Code of Federal Regulations, 2013 CFR

2013-07-01

... curtain incinerators that burn 100 percent yard waste? 60.1450 Section 60.1450 Protection of Environment... Air Curtain Incinerators That Burn 100 Percent Yard Waste § 60.1450 How must I monitor opacity for air curtain incinerators that burn 100 percent yard waste? (a) Use EPA Reference Method 9 in appendix A of...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2011 CFR

2011-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... percent wood wastes, clean lumber and/or yard waste? (a) After the date the initial test for opacity is...

40 CFR 62.14815 - What are the emission limitations for air curtain incinerators that burn 100 percent wood wastes...

Code of Federal Regulations, 2010 CFR

2010-07-01

... air curtain incinerators that burn 100 percent wood wastes, clean lumber and/or yard waste? 62.14815... Before November 30, 1999 Air Curtain Incinerators That Burn 100 Percent Wood Wastes, Clean Lumber And/or... percent wood wastes, clean lumber and/or yard waste? (a) After the date the initial test for opacity is...

Residual volume on land and when immersed in water: effect on percent body fat.

PubMed

Demura, Shinichi; Yamaji, Shunsuke; Kitabayashi, Tamotsu

2006-08-01

There is a large residual volume (RV) error when assessing percent body fat by means of hydrostatic weighing. It has generally been measured before hydrostatic weighing. However, an individual's maximal exhalations on land and in the water may not be identical. The aims of this study were to compare residual volumes and vital capacities on land and when immersed to the neck in water, and to examine the influence of the measurement error on percent body fat. The participants were 20 healthy Japanese males and 20 healthy Japanese females. To assess the influence of the RV error on percent body fat in both conditions and to evaluate the cross-validity of the prediction equation, another 20 males and 20 females were measured using hydrostatic weighing. Residual volume was measured on land and in the water using a nitrogen wash-out technique based on an open-circuit approach. In water, residual volume was measured with the participant sitting on a chair while the whole body, except the head, was submerged . The trial-to-trial reliabilities of residual volume in both conditions were very good (intraclass correlation coefficient > 0.98). Although residual volume measured under the two conditions did not agree completely, they showed a high correlation (males: 0.880; females: 0.853; P < 0.05). The limits of agreement for residual volumes in both conditions using Bland-Altman plots were -0.430 to 0.508 litres. This range was larger than the trial-to-trial error of residual volume on land (-0.260 to 0.304 litres). Moreover, the relationship between percent body fat computed using residual volume measured in both conditions was very good for both sexes (males: r = 0.902; females: r = 0.869, P < 0.0001), and the errors were approximately -6 to 4% (limits of agreement for percent body fat: -3.4 to 2.2% for males; -6.3 to 4.4% for females). We conclude that if these errors are of no importance, residual volume measured on land can be used when assessing body composition.