Joining Forces: A Response to Kathy Rentz from the European Perspective

ERIC Educational Resources Information Center

Louhiala-Salminen, Leena

2010-01-01

In this article, the author responds to Kathy Rentz. She happily joins forces for pedagogically defensible teaching conditions and gives a brief "activist" account from the European perspective. However, rather than "European," she emphasizes that for the most part, this response looks at business communication teachers'…

Weld Metallurgy and Mechanical Properties of High Manganese Ultra-high Strength Steel Dissimilar Welds

NASA Astrophysics Data System (ADS)

Dahmen, Martin; Lindner, Stefan; Monfort, Damien; Petring, Dirk

The increasing demand for ultra-high strength steels in vehicle manufacturing leads to the application of new alloys. This poses a challenge on joining especially by fusion welding. A stainless high manganese steel sheet with excellent strength and deformation properties stands in the centre of the development. Similar and dissimilar welds with a metastable austenitic steel and a hot formed martensitic stainless steel were performed. An investigation of the mixing effects on the local microstructure and the hardness delivers the metallurgical features of the welds. Despite of carbon contents above 0.4 wt.% none of the welds have shown cracks. Mechanical properties drawn from tensile tests deliver high breaking forces enabling a high stiffness of the joints. The results show the potential for the application of laser beam welding for joining in assembly of structural parts.

Increasing FSW join strength by optimizing feed rate, rotating speed and pin angle

NASA Astrophysics Data System (ADS)

Darmadi, Djarot B.; Purnowidodo, Anindito; Siswanto, Eko

2017-10-01

Principally the join in Friction Stir Welding (FSW) is formed due to mechanical bonding. At least there are two factors determines the quality of this join, first is the temperature in the area around the interface and secondly the intense of mixing forces in nugget zone to create the mechanical bonding. The adequate temperature creates good flowability of the nugget zone and an intensive mixing force produces homogeneous strong bonding. Based on those two factors in this research the effects of feed rate, rotating speed and pin angle of the FSW process to the tensile strength of resulted join are studied. The true experimental method was used. Feed rate was varied at 24, 42, 55 and 74 mm/minutes and from the experimental results, it can be concluded that the higher feed rate decreases the tensile strength of weld join and it is believed due to the lower heat embedded in the material. Inversely, the higher rotating speed increases the join’s tensile strength as a result of higher heat embedded in base metal and higher mixing force in the nugget zone. The rotating speed were 1842, 2257 and 2904 RPMs. The pin angle determines the direction of mixing force. With variation of pin angle: 0°, 4°, 8° and 12° the higher pin angle generally increases the tensile strength because of more intensive mixing force. For 12° pin angle the lower tensile strength is found since the force tends to push out the nugget area from the joint gap.

Second Shuttle Join NASA's STS Fleet: Challenger Launches First New Tracking Satellite

NASA Technical Reports Server (NTRS)

1983-01-01

NASA made a major stride in readying a second delivery vehicle for its Space Transportation System (STS) fleet with the perfect landing of Shuttle Orbiter Challenger at Edwards Air Force Base, California, April 9, 1983. Besides being the first flight test of Challenger's performance, the mission marked the orbiting of the first spacecraft in NASA's new Tracking and Data Relay Satellite System (TDRSS). The new family of orbiting space communications platforms is essential to serve future Shuttle missions. Although the Inertial Upper Stage (IUS) second stage engine firing failed to place TDRS in its final 35,888 kilometer (22,300 mile) geosynchronous orbit, its release from the orbiter cargo bay went as planned. Launch officials were confident they can achieve its planned orbit in a matter of weeks.

Proceedings of the Conference on Computer Generated Forces and Behavioral Representation (5th), Held in Orlando, Florida, on 9-11 May 1995

DTIC Science & Technology

1995-05-01

ForeSight ( MECFS ). Prior to joining TASC, Mr. Stanzione served as the deputy director of the Semi-Automated Forces group at Loral Advanced Distributed...TASC’s other Synthetic Environment programs, including Weather in DIS (WINDS) and Multi-Echelon CFOR with ForeSight ( MECFS ). Prior to joining TASC, Mr

Joining of graphene flakes by low energy N ion beam irradiation

NASA Astrophysics Data System (ADS)

Wu, Xin; Zhao, Haiyan; Pei, Jiayun; Yan, Dong

2017-03-01

An approach utilizing low energy N ion beam irradiation is applied in joining two monolayer graphene flakes. Raman spectrometry and atomic force microscopy show the joining signal under 40 eV and 1 × 1014 cm-2 N ion irradiation. Molecular dynamics simulations demonstrate that the joining phenomenon is attributed to the punch-down effect and the subsequent chemical bond generation between the two sheets. The generated chemical bonds are made up of inserted ions (embedded joining) and knocked-out carbon atoms (saturation joining). The electronic transport properties of the joint are also calculated for its applications.

Healthcare hath no fury. Power of religion and might of physicians join forces to prevent joint venture of faith-based Baptist Health, for-profit Triad Hospitals.

PubMed

Romano, Michael

2003-07-21

The power of religion and the might of physicians seem to have joined forces against Baptist Health System's proposed merger with for-profit Triad Hospitals. Doctors and employees of Baptist facilities such as Montclair Baptist Medical Center, left, demanded that the system remain faith-based and under local control.

Units

Science.gov Websites

Maxwell Air Force Base Maxwell Air Force Base Join the Air Force Home News AF News Commentaries Services SAPR FOIA Retiree Activities Office Centennial Search Maxwell Air Force Base: Home > Units Site

Robust Joining and Assembly Technologies for Ceramic Matrix Composites: Technical Challenges and Opportunities

NASA Technical Reports Server (NTRS)

Mrityunjay, Singh; Gray, Hugh R. (Technical Monitor)

2002-01-01

Fiber reinforced ceramic matrix composites are under active consideration for use in a wide variety of high temperature applications within the aeronautics, energy, process, and nuclear industries. The engineering designs require fabrication and manufacturing of complex shaped parts. In many instances, it is more economical to build up complex shapes by Joining simple geometrical shapes. Thus, joining and attachment have been recognized as enabling technologies for successful utilization of ceramic components in various demanding applications. In this presentation, various challenges and opportunities in design, fabrication, and testing of high temperature joints in ceramic matrix composites will be presented. Various joint design philosophies and design issues in joining of composites will be discussed along with an affordable, robust ceramic joining technology (ARCJoinT). A wide variety of ceramic composites, in different shapes and sizes, have been joined using this technology. Microstructure and mechanical properties of joints will be reported. Current status of various ceramic joining technologies and future prospects for their applications will also be discussed.

Enabling Dissimilar Material Joining Using Friction Stir Scribe Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hovanski, Yuri; Upadyay, Piyush; Kleinbaum, Sarah

2017-04-05

One challenge in adapting welding processes to dissimilar material joining is the diversity of melting temperatures of the different materials. Although the use of mechanical fasteners and adhesives have mostly paved the way for near-term implementation of dissimilar material systems, these processes only accentuate the need for low-cost welding processes capable of joining dissimilar material components regardless of alloy, properties, or melting temperature. Friction stir scribe technology was developed to overcome the challenges of joining dissimilar material components where melting temperatures vary greatly, and properties and/or chemistry are not compatible with more traditional welding processes. Although the friction stir scribemore » process is capable of joining dissimilar metals and metal/polymer systems, a more detailed evaluation of several aluminum/steel joints is presented herein to demonstrate the ability to both chemically and mechanically join dissimilar materials.« less

Enabling Dissimilar Material Joining Using Friction Stir Scribe Technology

DOE PAGES

Hovanski, Yuri; Upadyay, Piyush; Kleinbaum, Sarah; ...

2017-04-05

One challenge in adapting welding processes to dissimilar material joining is the diversity of melting temperatures of the different materials. Although the use of mechanical fasteners and adhesives have mostly paved the way for near-term implementation of dissimilar material systems, these processes only accentuate the need for low-cost welding processes capable of impartially joining dissimilar material components regardless of alloy, properties, or melting temperature. Friction stir scribe technology was developed to overcome the challenges of joining dissimilar material components where melting temperatures vary greatly, and properties and/or chemistry are not compatible with more traditional welding processes. Finally, although the frictionmore » stir scribe process is capable of joining dissimilar metals and metal/polymer systems, a more detailed evaluation of several aluminum/steel joints is presented herein to demonstrate the ability to both chemically and mechanically join dissimilar materials.« less

Prospects of joining multi-material structures

NASA Astrophysics Data System (ADS)

Sankaranarayanan, R.; Hynes, N. Rajesh Jesudoss

2018-05-01

Spring up trends and necessities make the pipelines for the brand new Technologies. The same way, Multimaterial structures emerging as fruitful alternatives for the conventional structures in the manufacturing sector. Especially manufacturing of transport vehicles is placing a perfect platform for these new structures. Bonding or joining technology plays a crucial role in the field of manufacturing for sustainability. These latest structures are purely depending on such joining technologies so that multi-material structuring can be possible practically. The real challenge lies on joining dissimilar materials of different properties and nature. Escalation of thermoplastic usage in large structural components also faces similar ambiguity for joining multi-material structures. Adhesive bonding, mechanical fastening and are the answering technologies for multi-material structures. This current paper analysis the prospects of these bonding technologies to meet the challenges of tomorrow.

Joined concentric tubes

DOEpatents

DeJonghe, Lutgard; Jacobson, Craig; Tucker, Michael; Visco, Steven

2013-01-01

Tubular objects having two or more concentric layers that have different properties are joined to one another during their manufacture primarily by compressive and friction forces generated by shrinkage during sintering and possibly mechanical interlocking. It is not necessary for the concentric tubes to display adhesive-, chemical- or sinter-bonding to each other in order to achieve a strong bond. This facilitates joining of dissimilar materials, such as ceramics and metals.

Factors Influencing Provision of Play and Learning Materials among Children with Physical Challenges. A Case Study of Joytown Special School, Kiambu County

ERIC Educational Resources Information Center

Muthoni, Kamau Joyce

2016-01-01

In Kenya there is still a high population of children either born with or who develop physical challenges. These children are often neglected and most do not join school at the expected age. In joining school they encounter several difficulties in their play and learning activities. These children with physical challenges have developmental needs…

Impact of Short-Range Forces on Defect Production from High-Energy Collisions

DOE PAGES

Stoller, R. E.; Tamm, A.; Béland, L. K.; ...

2016-04-25

Primary radiation damage formation in solid materials typically involves collisions between atoms that have up to a few hundred keV of kinetic energy. The distance between two colliding atoms can approach 0.05 nm during these collisions. At such small atomic separations, force fields fitted to equilibrium properties tend to significantly underestimate the potential energy of the colliding dimer. To enable molecular dynamics simulations of high-energy collisions, it is common practice to use a screened Coulomb force field to describe the interactions and to smoothly join this to the equilibrium force field at a suitable interatomic spacing. But, there is nomore » accepted standard method for choosing the parameters used in the joining process, and our results prove that defect production is sensitive to how the force fields are linked. A new procedure is presented that involves the use of ab initio calculations to determine the magnitude and spatial dependence of the pair interactions at intermediate distances, along with systematic criteria for choosing the joining parameters. Results are presented for the case of nickel, which demonstrate the use and validity of the procedure.« less

Pulse joining cartridges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golovashchenko, Sergey Fedorovich; Bonnen, John Joseph Francis

A pulsed joining tool includes a tool body that defines a cavity that receives an inner tubular member and an outer tubular member and a pulse joining cartridge. The tubular members are nested together with the cartridge being disposed around the outer tubular member. The cartridge includes a conductor, such as a wire or foil, that extends around the outer tubular member and is insulated to separate a supply segment from a return segment. A source of stored electrical energy is discharged through the conductor to join the tubular members with an electromagnetic force pulse.

Pulse joining cartridges

DOEpatents

Golovashchenko, Sergey Fedorovich; Bonnen, John Joseph Francis

2016-08-23

A pulsed joining tool includes a tool body that defines a cavity that receives an inner tubular member and an outer tubular member and a pulse joining cartridge. The tubular members are nested together with the cartridge being disposed around the outer tubular member. The cartridge includes a conductor, such as a wire or foil, that extends around the outer tubular member and is insulated to separate a supply segment from a return segment. A source of stored electrical energy is discharged through the conductor to join the tubular members with an electromagnetic force pulse.

The Joining-Up Process: Issues in Effective Human Resource Development

ERIC Educational Resources Information Center

Frohman, Alan L.; Kotter, John P.

1975-01-01

Four specific problems associated with ineffective and expensive joining-up which are examined in the article are: (1) mismatched expectations; (2) stifling creativity and challenge; (3) lack of managerial awareness and sensitivity to joining-up issues; and (4) using inappropriate or incomplete screening criteria. Solutions are suggested; a table…

In-network processing of joins in wireless sensor networks.

PubMed

Kang, Hyunchul

2013-03-11

The join or correlated filtering of sensor readings is one of the fundamental query operations in wireless sensor networks (WSNs). Although the join in centralized or distributed databases is a well-researched problem, join processing in WSNs has quite different characteristics and is much more difficult to perform due to the lack of statistics on sensor readings and the resource constraints of sensor nodes. Since data transmission is orders of magnitude more costly than processing at a sensor node, in-network processing of joins is essential. In this paper, the state-of-the-art techniques for join implementation in WSNs are surveyed. The requirements and challenges, join types, and components of join implementation are described. The open issues for further research are identified.

In-Network Processing of Joins in Wireless Sensor Networks

PubMed Central

Kang, Hyunchul

2013-01-01

The join or correlated filtering of sensor readings is one of the fundamental query operations in wireless sensor networks (WSNs). Although the join in centralized or distributed databases is a well-researched problem, join processing in WSNs has quite different characteristics and is much more difficult to perform due to the lack of statistics on sensor readings and the resource constraints of sensor nodes. Since data transmission is orders of magnitude more costly than processing at a sensor node, in-network processing of joins is essential. In this paper, the state-of-the-art techniques for join implementation in WSNs are surveyed. The requirements and challenges, join types, and components of join implementation are described. The open issues for further research are identified. PMID:23478603

Robust Joining and Integration of Advanced Ceramics and Composites: Challenges, Opportunities, and Realities

NASA Technical Reports Server (NTRS)

Singh, Mrityunjay

2006-01-01

Advanced ceramics and fiber reinforced composites are under active consideration for use in a wide variety of high temperature applications within the aeronautics, space transportation, energy, and nuclear industries. The engineering designs of ceramic and composite components require fabrication and manufacturing of large and complex shaped parts of various thicknesses. In many instances, it is more economical to build up complex shapes by joining simple geometrical shapes. In addition, these components have to be joined or assembled with metallic sub-components. Thus, joining and attachment have been recognized as enabling technologies for successful utilization of ceramic components in various demanding applications. In this presentation, various challenges and opportunities in design, fabrication, and testing of high temperature joints in advanced ceramics and ceramic matrix composites will be presented. Silicon carbide based advanced ceramics and fiber reinforced composites in different shapes and sizes, have been joined using an affordable, robust ceramic joining technology. In addition, some examples of metal-ceramic brazing will also be presented. Microstructure and high temperature mechanical properties of joints in silicon carbide ceramics and composites will be reported. Various joint design philosophies and design issues in joining of ceramics and composites will be discussed.

JOINING DISSIMILAR MATERIALS USING FRICTION STIR SCRIBE TECHNIQUE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep

2016-09-01

Development of robust and cost effective method of joining dissimilar materials can provide a critical pathway to enable widespread use of multi-material design and components in mainstream industrial applications. The use of multi-material components such as Steel-Aluminum, Aluminum-Polymer allows design engineers to optimize material utilization based on service requirements and often lead weight and cost reductions. However producing an effective joint between materials with vastly different thermal, microstructural and deformation response is highly problematic using conventional joining and /or fastening methods. This is especially challenging in cost sensitive high volume markets that largely rely on low–cost joining solutions. Friction Stirmore » Scribe technology was developed to meet the demands of joining materials with drastically different properties and melting regimes. The process enables joining of light metals like Magnesium and Aluminum to high temperature materials like Steels and Titanium. Additionally viable joints between polymer composites and metal can also be made using this method. This paper will present state of the art, progress made and challenges associated with this innovative derivative of Friction Stir welding in reference to joining dissimilar metals and polymer/metal combinations.« less

Joining Dissimilar Materials Using Friction Stir Scribe Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep

2016-10-03

Development of a robust and cost-effective method of joining dissimilar materials could provide a critical pathway to enable widespread use of multi-material designs and components in mainstream industrial applications. The use of multi-material components such as steel-aluminum and aluminum-polymer would allow design engineers to optimize material utilization based on service requirements and could often lead to weight and cost reductions. However, producing an effective joint between materials with vastly different thermal, microstructural, and deformation responses is highly problematic using conventional joining and/or fastening methods. This is especially challenging in cost sensitive, high volume markets that largely rely on low costmore » joining solutions. Friction stir scribe technology was developed to meet the demands of joining materials with drastically different properties and melting regimes. The process enables joining of light metals like magnesium and aluminum to high temperature materials like steel and titanium. Viable joints between polymer composites and metal can also be made using this method. This paper will present the state of the art, progress made, and challenges associated with this innovative derivative of friction stir welding in reference to joining dissimilar metals and polymer/metal combinations.« less

Transitions between states of labor-force participation among older Israelis.

PubMed

Achdut, Leah; Tur-Sinai, Aviad; Troitsky, Rita

2015-03-01

The study examines the labor-force behavior of Israelis at older ages, focusing on the determinants of the transitions between states of labor-force participation between 2005 and 2010. The study uses panel data from the first two waves of the SHARE-Israel longitudinal survey. A multinomial logit model is used to examine the impact of sociodemographic characteristics, health state, and economic resources on labor-force transitions of people aged 50-67. The results emphasize the role of age and poor health in "pushing" older people out of the labor force or "keeping" them there. Spouse's participation is found to encourage individuals to leave the labor force or to refrain from joining it. However, living with a participating spouse is negatively associated with staying out of the labor force, consistent with the dominance of the complementarity of leisure effect found in the literature. Wealth as an economic resource available to individuals for retirement is also found to encourage individuals to leave the labor force or to refrain from joining it.

Air Force Medical Service > Resources > Suicide Prevention

Science.gov Websites

Air Force Medical Service Air Force Medical Service Join the Air Force Home Your Healthcare Healthy Videos MHS Genesis AFMS Priorities Trusted Care Vision Air Force Medical Home Full Spectrum Medical ) Air Force EFMP Who is an EFM? Who must enroll? EFMP-Medical EFMP-M Objectives Family Criteria EFMP-M

PRN 94-9: Announcing the Formation of Two Industry-Wide Task Forces: Agricultural Reentry Task Force and Outdoor Residential Exposure Task Force

EPA Pesticide Factsheets

This Notice announces two industry-wide Task Forces being formed in response to generic exposure data requirements. It contains EPA's policy on a registrant's options for, and responsibilities when joining Task Force as a way to satisfy data requirements.

Logistics modelling: improving resource management and public information strategies in Florida.

PubMed

Walsh, Daniel M; Van Groningen, Chuck; Craig, Brian

2011-10-01

One of the most time-sensitive and logistically-challenging emergency response operations today is to provide mass prophylaxis to every man, woman and child in a community within 48 hours of a bioterrorism attack. To meet this challenge, federal, state and local public health departments in the USA have joined forces to develop, test and execute large-scale bioterrorism response plans. This preparedness and response effort is funded through the US Centers for Disease Control and Prevention's Cities Readiness Initiative, a programme dedicated to providing oral antibiotics to an entire population within 48 hours of a weaponised inhalation anthrax attack. This paper will demonstrate how the State of Florida used a logistics modelling tool to improve its CRI mass prophylaxis plans. Special focus will be on how logistics modelling strengthened Florida's resource management policies and validated its public information strategies.

B-52 Stratofortress joins coalition team > U.S. Air Force > Article Display

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

Laser microjoining of dissimilar and biocompatible materials

NASA Astrophysics Data System (ADS)

Bauer, Ingo; Russek, Ulrich A.; Herfurth, Hans J.; Witte, Reiner; Heinemann, Stefan; Newaz, Golam; Mian, A.; Georgiev, D.; Auner, Gregory W.

2004-07-01

Micro-joining and hermetic sealing of dissimilar and biocompatible materials is a critical issue for a broad spectrum of products such as micro-electronics, micro-optical and biomedical products and devices. Today, biocompatible titanium is widely applied as a material for orthopedic implants as well as for the encapsulation of implantable devices such as pacemakers, defibrillators, and neural stimulator devices. Laser joining is the process of choice to hermetically seal such devices. Laser joining is a contact-free process, therefore minimizing mechanical load on the parts to be joined and the controlled heat input decreases the potential for thermal damage to the highly sensitive components. Laser joining also offers flexibility, shorter processing time and higher quality. However, novel biomedical products, in particular implantable microsystems currently under development, pose new challenges to the assembly and packaging process based on the higher level of integration, the small size of the device's features, and the type of materials and material combinations. In addition to metals, devices will also include glass, ceramic and polymers as biocompatible building materials that must be reliably joined in similar and dissimilar combinations. Since adhesives often lack long-term stability or do not meet biocompatibility requirements, new joining techniques are needed to address these joining challenges. Localized laser joining provides promising developments in this area. This paper describes the latest achievements in micro-joining of metallic and non-metallic materials with laser radiation. The focus is on material combinations of metal-polymer, polymer-glass, metal-glass and metal-ceramic using CO2, Nd:YAG and diode laser radiation. The potential for applications in the biomedical sector will be demonstrated.

Ultrapulse welding: A new joining technique. [for automotive industry

NASA Technical Reports Server (NTRS)

Anderson, D. G.

1972-01-01

The ultrapulse process is a resistance welding process that utilizes unidirectional current of high magnitude for a very short time with a precisely controlled dynamic force pulse. Peak currents of up to 220,000 amperes for two to ten milliseconds are used with synchronized force pulses of up to nine thousand pounds. The welding current passing through the relatively high resistance of the interface between the parts that are being joined results in highly localized heating. Described is the UPW process as it applies to the automotive industry.

The implementation of AI technologies in computer wargames

NASA Astrophysics Data System (ADS)

Tiller, John A.

2004-08-01

Computer wargames involve the most in-depth analysis of general game theory. The enumerated turns of a game like chess are dwarfed by the exponentially larger possibilities of even a simple computer wargame. Implementing challenging AI is computer wargames is an important goal in both the commercial and military environments. In the commercial marketplace, customers demand a challenging AI opponent when they play a computer wargame and are frustrated by a lack of competence on the part of the AI. In the military environment, challenging AI opponents are important for several reasons. A challenging AI opponent will force the military professional to avoid routine or set-piece approaches to situations and cause them to think much deeper about military situations before taking action. A good AI opponent would also include national characteristics of the opponent being simulated, thus providing the military professional with even more of a challenge in planning and approach. Implementing current AI technologies in computer wargames is a technological challenge. The goal is to join the needs of AI in computer wargames with the solutions of current AI technologies. This talk will address several of those issues, possible solutions, and currently unsolved problems.

Advanced concepts in joining by conventional processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edwards, G.R.; Fasching-James, A.A.; Onsoien, M.I.

1994-12-31

Innovations which can be made to conventional arc welding processes so that advanced materials can be more efficiently joined are considered. Three examples are discussed: (1) GTA welding of iron aluminides, (2) GMA welding of advanced steels, and (3) SMA welding of structural steels. Advanced materials present new challenges for the materials joining specialist. The three examples discussed in this paper demonstrate, however, that modest but creative alterations of conventional GTAW, GMAW, or SMAW processes can provide new and better controls for solving advanced materials joining problems.

Self-force as a probe of global structure

NASA Astrophysics Data System (ADS)

Davidson, Karl; Poisson, Eric

2018-05-01

We calculate the self-force on an electric charge and electric dipole held at rest in a closed universe that results from joining two copies of Minkowski spacetime at a common boundary. Spacetime is strictly flat on each side of the boundary, but there is curvature at the surface layer required to join the two Minkowski spacetimes. We find that the self-force on the charge is always directed away from the surface layer. This is analogous to the case of an electric charge held at rest inside a spherical shell of matter, for which the self-force is also directed away from the shell. For the dipole, the direction of the self-force is a function of the dipole's position and orientation. Both self-forces become infinite when the charge or dipole is made to approach the surface layer. This study reveals that a self-force can arise even when the Riemann tensor vanishes at the position of the charge or dipole; in such cases the self-force is a manifestation of the global curvature of spacetime.

Influence of clamp-up force on the strength of bolted composite joints

NASA Astrophysics Data System (ADS)

Horn, Walter J.; Schmitt, Ron R.

1994-03-01

Composite materials offer the potential for a reduction in the number of individual parts and joints in a structure because large one-piece components can replace multipart assemblies. Nevertheless, there are many situations where composite parts must be joined and often mechanical fasteners provide the only practical method of joining those parts. The long-term strength of mechanically fastened joints of composite members can be directly affected by the clamp-up force of the fastener and thus perhaps by the relaxation of this force due to the viscoelastic character of the composite materials of the joint. Methods for predicting the effect of bolt clamp-up force relaxation on the strength of mechanically fastened joints of thermoplastic composite materials were investigated during the present study. A test program, using two thermoplastic composite materials, was conducted to determine the influence of clamp-up force on joint strength, to measure the relaxation of the joint clamp-up force with time, and to measure the change of joint strength as a function of time.

Conjoint Forming - Technologies for Simultaneous Forming and Joining

NASA Astrophysics Data System (ADS)

Groche, P.; Wohletz, S.; Mann, A.; Krech, M.; Monnerjahn, V.

2016-03-01

The market demand for new products optimized for e. g. lightweight applications or smart components leads to new challenges in production engineering. Hybrid structures represent one promising approach. They aim at higher product performance by using a suitable combination of different materials. The developments of hybrid structures stimulate the research on joining of dissimilar materials. Since they allow for joining dissimilar materials without external heating technologies based on joining by plastic deformation seem to be of special attractiveness. The paper at hand discusses the conjoint forming approach. This approach combines forming and joining in one process. Two or more workpieces are joined while at least one workpiece is plastically deformed. After presenting the fundamental joining mechanisms, the conjoint forming approach is discussed comprehensively. Examples of conjoint processes demonstrate the effectiveness and reveal the underlying phenomena.

Joining Forces: Integrating Proteomics and Cross-linking with the Mass Spectrometry of Intact Complexes*

PubMed Central

Stengel, Florian; Aebersold, Ruedi; Robinson, Carol V.

2012-01-01

Protein assemblies are critical for cellular function and understanding their physical organization is the key aim of structural biology. However, applying conventional structural biology approaches is challenging for transient, dynamic, or polydisperse assemblies. There is therefore a growing demand for hybrid technologies that are able to complement classical structural biology methods and thereby broaden our arsenal for the study of these important complexes. Exciting new developments in the field of mass spectrometry and proteomics have added a new dimension to the study of protein-protein interactions and protein complex architecture. In this review, we focus on how complementary mass spectrometry-based techniques can greatly facilitate structural understanding of protein assemblies. PMID:22180098

Integrating parasitology and marine ecology: Seven challenges towards greater synergy

NASA Astrophysics Data System (ADS)

Poulin, Robert; Blasco-Costa, Isabel; Randhawa, Haseeb S.

2016-07-01

Despite their very different historical origins as scientific disciplines, parasitology and marine ecology have already combined successfully to make important contributions to our understanding of the functioning of natural ecosystems. For example, robust assessments of the contribution of parasites to ecosystem biomass and energetics, and of their impact on community-wide biodiversity and food web structure, have all been made for the first time in marine systems. Nevertheless, for the marriage between parasitology and marine ecology to remain fruitful, several challenges must first be overcome. We discuss seven such challenges on the road to a greater synergy between these disciplines: (1) Raising awareness of parasitism as an ecological force by increasing the proportion of articles about parasites and diseases in marine ecology journals; (2) Making greater use of theory and conceptual frameworks from marine ecology to guide parasitological research; (3) Speeding up or at least maintaining the current rate at which marine parasites are found and described; (4) Elucidating a greater proportion of life cycles in all major groups of marine parasites; (5) Increasing the number of host-parasite model systems on which our knowledge is based; (6) Extending parasitological research offshore and into ocean depths; and (7) Developing, as needed, new epidemiological theory and transmission models for the marine environment. None of these challenges is insurmountable, and addressing just a few of them should guarantee that parasitology and marine ecology will continue to join forces and make further substantial contributions.

Concept for a fast analysis method of the energy dissipation at mechanical joints

NASA Astrophysics Data System (ADS)

Wolf, Alexander; Brosius, Alexander

2017-10-01

When designing hybrid parts and structures one major challenge is the design, production and quality assessment of the joining points. While the polymeric composites themselves have excellent material properties, the necessary joints are often the weak link in assembled structures. This paper presents a method of measuring and analysing the energy dissipation at mechanical joining points of hybrid parts. A simplified model is applied based on the characteristic response to different excitation frequencies and amplitudes. The dissipation from damage is the result of relative moments between joining partners und damaged fibres within the composite, whereas the visco-elastic material behaviour causes the intrinsic dissipation. The ambition is to transfer these research findings to the characterisation of mechanical joints in order to quickly assess the general quality of the joint with this non-destructive testing method. The inherent challenge for realising this method is the correct interpretation of the measured energy dissipation and its attribution to either a bad joining point or intrinsic material properties. In this paper the authors present the concept for energy dissipation measurements at different joining points. By inverse analysis a simplified fast semi-analytical model will be developed that allows for a quick basic quality assessment of a given joining point.

Air Force Special Operations Command > Home > POTFF

Science.gov Websites

Air Force Special Operations Command Air Force Special Operations Command Join the Air Force Home Sheets AFSOC Senior Leaders AFSOC Heritage Units 1st Special Operations Wing 24th Special Operations Wing 27th Special Operations Wing 352nd Special Operations Wing 353rd Special Operations Group 492nd Special

Joining Others for Community Economic Development.

ERIC Educational Resources Information Center

Borgen, Joseph A.; Shade, William B.

1984-01-01

Examines the basic principles of economic development and provides a case study of the Communitywide Work Force Development Project, which was designed to involve the community in solving the economic development and work force problems of Terre Haute, Indiana. (DMM)

All-round joining method with carbon fiber reinforced interface

NASA Astrophysics Data System (ADS)

Miwa, Noriyoshi; Tanaka, Kazunori; Kamiya, Yoshiko; Nishi, Yoshitake

2008-08-01

Carbon fiber reinforced polymer (CFRP) has been recently applied to not only wing, but also fan blades of turbo fan engines. To prevent impact force, leading edge of titanium was often mounted on the CFRP fan blades with adhesive force. In order to enhance the joining strength, a joining method with carbon fiber reinforced interface has been developed. By using nickel-coated carbon fibers, a joining sample with carbon fiber-reinforced interface between CFRP and CFRM has been successfully developed. The joining sample with nickel-coated carbon fiber interface exhibits the high tensile strength, which was about 10 times higher than that with conventional adhesion. On the other hand, Al-welding methods to steel, Cu and Ti with carbon fiber reinforced interface have been successfully developed to lighten the parts of machines of racing car and airplane. Carbon fibers in felt are covered with metals to protect the interfacial reaction. The first step of the welding method is that the Al coated felt is contacted and wrapped with molten aluminum solidified under gravity pressure, whereas the second step is that the felt with double layer of Ni and Al is contacted and wrapped with molten steel (Cu or Ti) solidified under gravity pressure. Tensile strength of Al-Fe (Cu or Ti) welded sample with carbon fiber reinforced interface is higher than those of Al-Fe (Cu or Ti) welded sample.

Aeroelastic Analysis Of Joined Wing Of High Altitude Long Endurance (HALE) Aircraft Based On The Sensor-Craft Configuration

NASA Astrophysics Data System (ADS)

Marisarla, Soujanya; Ghia, Urmila; "Karman" Ghia, Kirti

2002-11-01

Towards a comprehensive aeroelastic analysis of a joined wing, fluid dynamics and structural analyses are initially performed separately. Steady flow calculations are currently performed using 3-D compressible Navier-Stokes equations. Flow analysis of M6-Onera wing served to validate the software for the fluid dynamics analysis. The complex flow field of the joined wing is analyzed and the prevailing fluid dynamic forces are computed using COBALT software. Currently, these forces are being transferred as fluid loads on the structure. For the structural analysis, several test cases were run considering the wing as a cantilever beam; these served as validation cases. A nonlinear structural analysis of the wing is being performed using ANSYS software to predict the deflections and stresses on the joined wing. Issues related to modeling, and selecting appropriate mesh for the structure were addressed by first performing a linear analysis. The frequencies and mode shapes of the deformed wing are obtained from modal analysis. Both static and dynamic analyses are carried out, and the results obtained are carefully analyzed. Loose coupling between the fluid and structural analyses is currently being examined.

Industrial Robots Join the Work Force.

ERIC Educational Resources Information Center

Martin, Gail M.

1982-01-01

Robots--powerful, versatile, and easily adapted to new operations--may usher in a new industrial age. Workers throughout the labor force could be affected, as well as the nature of the workplace, skill requirements of jobs, and concomitant shifts in vocational education. (SK)

Innovative and Highly Productive Joining Technologies for Multi-Material Lightweight Car Body Structures

NASA Astrophysics Data System (ADS)

Meschut, G.; Janzen, V.; Olfermann, T.

2014-05-01

Driven by increasing costs for energy and raw material and especially by the European CO2-emission laws, automotive industry faces the challenge to develop more lightweight and at the same time still rigid and crash-stable car bodies, that are affordable for large-scale production. The implementation of weight-reduced constructions depends not only on the availability of lightweight materials and related forming technologies, but also on cost-efficient and reliable joining technologies suitable for multi-material design. This article discusses the challenges and requirements for these technologies, based on the example of joining aluminium with press-hardened boron steels, what is considered as a very important material combination for affordable future lightweight mobility. Besides a presentation of recent developments for extending the process limits of conventional mechanical joining methods, new promising technologies such as resistance element welding are introduced. In addition, the performance, advantages, and disadvantages of the presented technologies are compared and discussed.

All about Forces & Gravity. Physical Science for Children[TM]. Schlessinger Science Library. [Videotape].

ERIC Educational Resources Information Center

2000

A force is a push or a pull. In All About Forces and Gravity, kids will join our host on a parasailing adventure to investigate how forces impact and shape everything that happens in the world around us. Learn about gravity and the work of Sir Isaac Newton, the English scientists whose scientific principles forever changed the way people looked at…

Connecting the Dots: Enduring Challenges in the Nation’s Information Sharing Environment

DTIC Science & Technology

2010-05-12

mails describes an exchange in which Major Hassan wrote, “I can’t wait to join you” in the afterlife . 113...Hassan’s email: ‘I Can’t Wait to Join You’ in Afterlife ,” ABC News, (November 19, 2009). http://abcnews.go.com/Blotter/major-hasans-mail-wait-join... afterlife /story?id=9130339 (accessed January 12, 2010). 112Senate and Homeland Security and Governmental Affairs Committee, Statement by Juan Carlos

Astronaut Sullivan prepares to join crew in training

NASA Image and Video Library

1984-09-04

41D-3188 (2 September 1984) --- Astronaut Kathryn D. Sullivan, 41-G mission specialist, joins with other members of the seven-person crew prior to a training session in the Shuttle mockup and integration laboratory at the Johnson Space Center. Dr. Sullivan will be the first American woman to perform an extravehicular activity (EVA) in space when she joins Astronaut David C. Leestma for some outside-the-Challenger duty on October 9. The mission is scheduled for an October 5, 1984 launch.

Living History: Pioneering Bandswomen of the United States Air Force

ERIC Educational Resources Information Center

Nichols, Jeananne

2015-01-01

This narrative describes two United States Air Force bandswomen whose combined careers span the past sixty years. Cornetist Martha (Martye) Jean Awkerman joined the U.S. Women in the Air Force (WAF) Band in 1955. She served the WAF band as cornet soloist and principal trumpet until the band was disbanded in 1961. In 1983, tubist Jan Duga joined…

Evaluating the Upset Protrusion Joining (UPJ) Method to Join magnesium Castings to Dissimilar Metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, Stephen D.

2015-08-19

This presentation discusses advantages and best practices for incorporating magnesium in automotive component applications to achieve substantial mass reduction, as well as some of the key challenges with respect to joining, coating, and galvanic corrosion, before providing an introduction and status update of the U.S. Department of Energy and Department of Defense jointly sponsored Upset Protrusion Joining (UPJ) process development and evaluation project. This update includes sharing performance results of a benchmark evaluation of the self-pierce riveting (SPR) process for joining dissimilar magnesium (Mg) to aluminum (Al) materials in four unique coating configurations before introducing the UPJ concept and comparingmore » performance results of the joints made with the UPJ process to those made with the SPR process.« less

Viet Cong Recruitment: Why and How Men Join

DTIC Science & Technology

1967-12-01

have been subordinated to the demands of intensified warfare. Today, more and more youths in their early teens are performing nonmilitary, paramilitary...women, influenced by their noble example, or moved to join the movement to impress the girls of their village.) Though forcible recruitment, including...sisters who died heroically while leading Vietnamese forces in battle against the Chinese. The Viet Cong is skillful in exploiting the appeal of girls

East Europe Report

DTIC Science & Technology

1986-12-02

communist is an existential choice and investment, which does not mean joining the "party" for private gain or mere political sub- sistence in it...have the greatest existential interest in them, whose living conditions are such that they must long for them but only If they join forces with all...Naturally, the role of the intelligentsia, and not only the " humanist intelli- gentsia but all of the. intelligentsia that combines knowledge and

The Flying Diamond: A joined aircraft configuration design project, volume 1

NASA Technical Reports Server (NTRS)

Ball, Chris; Czech, Joe; Lentz, Bryan; Kobashigawa, Daryl; Oishi, Curtis; Poladian, David

1988-01-01

The results of the analysis conducted on the Joined Wing Configuration study are presented. The joined wing configuration employs a conventional fuselage and incorporates two wings joined together near their tips to form a diamond shape in both plan view and front view. The arrangement of the lifting surfaces uses the rear wing as a horizontal tail and as a forward wing strut. The rear wing has its root at the tip of the vertical stabilizer and is structurally attached to the trailing edge of the forward wing. This arrangement of the two wings forms a truss structure which is inherently resistant to the aerodynamic bending loads generated during flight. This allows for a considerable reduction in the weight of the lifting surfaces. With smaller internal wing structures needed, the Joined Wing may employ thinner wings which are more suitable for supersonic and hypersonic flight, having less induced drag than conventional cantilever winged aircraft. Inherent in the Joined Wing is the capability of the generation of direct lift and side force which enhance the performance parameters.

Friction Stir Weld Tooling Development for Application on the 2195 Al-Cu-Li Space Transportation System External Tank

NASA Technical Reports Server (NTRS)

Loftus, Zachary; Arbegast, W. J.; Hartley, P. J.

1998-01-01

Friction Stir Welding (FSW) is a new and innovative solid-state joining process which can be applied to difficult-to- weld aluminum alloys. However, the large forces involved with the process have posed a production tooling challenge. Lockheed Martin Michoud Space Systems has overcome many of these challenges on the Super Lightweight External Tank (ET) program. Utilizing Aluminum-Copper-Lithium alloy 2195 in the form of plate and extrusions, investigations of FSW process parameters have been completed. Major loading mechanisms are discussed in conjunction with deflection measurements. Since the ET program is a cryogenic application, a brief comparison of cryogenic material properties with room temperature material properties is offered for both FSW and fusion welds. Finally, a new approach to controlling the FSW process from a load perspective is introduced. Emphasis will be put on tooling development, as well as the impact of tooling design and philosophy on Friction Stir Weld success probability.

Developing Diversity Initiatives: Definitions and Process.

ERIC Educational Resources Information Center

Duncan, Roberto A.

U.S. business and government are managing an increasingly heterogeneous work force. Between 1985 and 2000, white females, nonwhites, and immigrants are projected to represent 88 percent of new workers. Approximately 4 million new immigrant workers will join the work force during the next 10 years. Therefore, it is imperative that employers…

Chrysler Upset Protrusion Joining Techniques for Joining Dissimilar Metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, Stephen

The project goal was to develop and demonstrate a robust, cost effective, and versatile joining technique, known as Upset Protrusion Joining (UPJ), for joining challenging dissimilar metal com-binations, especially those where one of the metals is a die cast magnesium (Mg) component. Since two of the key obstacles preventing more widespread use of light metals (especially in high volume automotive applications) are 1) a lack of robust joining techniques and 2) susceptibility to galvanic corrosion, and since the majority of the joint combinations evaluated in this project include die cast Mg (the lightest structural metal) as one of the twomore » materials being joined, and since die casting is the most common and cost effective process for producing Mg components, then successful project completion provides a key enabler to high volume application of lightweight materials, thus potentially leading to reduced costs, and encouraging implementation of lightweight multi-material vehicles for significant reductions in energy consumption and reduced greenhouse gas emissions. Eco-nomic benefits to end-use consumers are achieved primarily via the reduction in fuel consumption. Unlike currently available commercial processes, the UPJ process relies on a very robust mechanical joint rather than intermetallic bonding, so the more cathodic material can be coated prior to joining, thus creating a robust isolation against galvanic attack on the more anodic material. Additionally, since the UPJ protrusion is going through a hole that can be pre-drilled or pre-punched prior to coating, the UPJ process is less likely to damage the coating when the joint is being made. Further-more, since there is no additional cathodic material (such as a steel fastener) used to create the joint, there is no joining induced galvanic activity beyond that of the two parent materials. In accordance with its originally proposed plan, this project has successfully developed process variants of UPJ to enable joining of Mg die castings to aluminum (Al) and steel sheet components of various thicknesses, strengths and coating configurations. While most development focused on the simpler round boss version of the process, an additional phase of the work focused on devel-opment of an oval boss version to support applications with narrow flanges, while yet another vari-ant of the process, known as Upset Cast Riveting (UCR), was developed and evaluated for joining mixed metals that may not necessarily include Mg or Al die cast components. Although each varia-tion posed unique challenges described later in the report, all variations were successfully produced and evaluated, and each could be further developed for specific types of commercial applications. In this project, UPJ performed favorably against the benchmark self-pierce riveting (SPR) process in Mg AM60B to Al 6013 combinations although significant corrosion challenges were observed in both processes, especially for the bare Mg to bare Al configurations. Additional challenges were observed in joining Mg to steel with the UPJ process (SPR was not evaluated for this combination as it was not considered viable). To pass FCA’s specified corrosion tests with Mg/steel combina-tions, new steel treatments were evaluated, as well as adhesives and sealed edges. These showed significant improvement. In general, UPJ performed very well in Mg to Al 6016 combinations, even in corrosion evaluation of the bare Mg to bare Al configuration (again, SPR was not evaluated for this material combination as the 1.1 mm thick Al6016 sheet thickness was considered too thin for the SPR process). The improvement in corrosion performance of the Mg to Al 6016 combina-tion over the Mg to Al 6013 combination was thought to be a result of the lower copper content in the Al 6016 alloy. Oval boss joints showed substantial improvement in all joint strength criteria compared to 8.0-mm diameter round boss joints but were not evaluated for corrosion performance. The improved joint strength is likely a result of larger shear area. Cosmetic corrosion performance of all test assemblies (UPJ, UCR and SPR) was a challenge due to exposed edges and crevices al-lowing undercutting of the coatings. In real world component applications, the exposed edges, so prevalent on the joining test coupons, would be less prevalent and easier to protect.« less

Challenges, Ideas, and Innovations of Joined-Wing Configurations: A Concept from the Past, an Opportunity for the Future

NASA Astrophysics Data System (ADS)

Cavallaro, Rauno; Demasi, Luciano

2016-11-01

Diamond Wings, Strut- and Truss-Braced Wings, Box Wings, and PrandtlPlane, the so-called "JoinedWings", represent a dramatic departure from traditional configurations. Joined Wings are characterized by a structurally overconstrained layout which significantly increases the design space with multiple load paths and numerous solutions not available in classical wing systems. A tight link between the different disciplines (aerodynamics, flight mechanics, aeroelasticity, etc.) makes a Multidisciplinary Design and Optimization approach a necessity from the early design stages. Researchers showed potential in terms of aerodynamic efficiency, reduction of emissions and superior performances, strongly supporting the technical advantages of Joined Wings. This review will present these studies, with particular focus on the United States joined-wing SensorCraft, Strut- and Truss- Braced Wings, Box Wings and PrandtlPlane.

Hole-pin joining structure with fiber-round-hole distribution of lobster cuticle and biomimetic study.

PubMed

Chen, Bin; Fan, Jinghong; Gou, Jihua; Lin, Shiyun

2014-12-01

Observations of the cuticle of the Boston Spiny Lobster using scanning electron microscope (SEM) show that it is a natural biocomposite consisting of chitin fibers and sclerotic-protein matrix with hierarchical and helicoidal structure. The SEM images also indicate that there is a hole-pin joining structure in the cuticle. In this joining structure, the chitin fibers in the neighborhood of the joining holes continuously round the holes to form a fiber-round-hole distribution. The maximum pullout force of the fibers in the fiber-round-hole distribution, which is closely related to the fracture toughness of the cuticle, is investigated and compared with that of the fibers in non-fiber-round-hole distribution based on their representative models. It is revealed that the maximum pullout force of the fibers in the fiber-round-hole distribution is significantly larger than that of the fibers in the non-fiber-round-hole distribution, and that a larger diameter of the hole results in a larger difference in the maximum pullout forces of the fibers between the two kinds of the fiber distributions. Inspired by the fiber-round-hole distribution found in the cuticle, composite specimens with the fiber-round-hole distribution were fabricated with a special mold and process to mirror the fiber-round-hole distribution. The fracture toughness of the biomimetic composite specimens is tested and compared with that of the conventional composite specimens with the non-fiber-round-hole distribution. It is demonstrated that the fracture toughness of the biomimetic composite specimens with the fiber-round-hole distribution is significantly larger than that of the conventional composite specimens with the non-fiber-round-hole distribution. Copyright © 2014 Elsevier Ltd. All rights reserved.

Survival ethics in the real world: the research university and sustainable development.

PubMed

Verharen, Charles; Tharakan, John; Bugarin, Flordeliz; Fortunak, Joseph; Kadoda, Gada; Middendorf, George

2014-03-01

We discuss how academically-based interdisciplinary teams can address the extreme challenges of the world's poorest by increasing access to the basic necessities of life. The essay's first part illustrates the evolving commitment of research universities to develop ethical solutions for populations whose survival is at risk and whose quality of life is deeply impaired. The second part proposes a rationale for university responsibility to solve the problems of impoverished populations at a geographical remove. It also presents a framework for integrating science, engineering and ethics in the efforts of multidisciplinary teams dedicated to this task. The essay's third part illustrates the efforts of Howard University researchers to join forces with African university colleagues in fleshing out a model for sustainable and ethical global development.

Manufacturing Challenges Associated with the Use of Metal Matrix Composites in Aerospace Structures

NASA Technical Reports Server (NTRS)

Prater, Tracie

2014-01-01

Metal Matrix Composites (MMCs) consist of a metal alloy reinforced with ceramic particles or fibers. These materials possess a very high strength to weight ratio, good resistance to impact and wear, and a number of other properties which make them attractive for use in aerospace and defense applications. MMCs have found use in the space shuttle orbiter's structural tubing, the Hubble Space Telescope's antenna mast, control surfaces and propulsion systems for aircraft, and tank armors. The size of MMC components is severely limited by difficulties encountered in joining these materials using fusion welding. Melting of the material results in formation of an undesirable phase (formed when molten Aluminum reacts with the reinforcement) which leaves a strength depleted region along the joint line. Friction Stir Welding (FSW) is a relatively nascent solid state joining technique developed at The Welding Institute (TWI) in 1991. The process was first used at NASA to weld the super lightweight external tank for the Space Shuttle. Today FSW is used to join structural components of the Delta IV, Atlas V, and Falcon IX rockets as well as NASA's Orion Crew Exploration Vehicle and Space Launch System. A current focus of FSW research is to extend the process to new materials, such as MMCs, which are difficult to weld using conventional fusion techniques. Since Friction Stir Welding occurs below the melting point of the workpiece material, this deleterious phase is absent in FSW-ed MMC joints. FSW of MMCs is, however, plagued by rapid wear of the welding tool, a consequence of the large discrepancy in hardness between the steel tool and the reinforcement material. This chapter summarizes the challenges encountered when joining MMCs to themselves or to other materials in structures. Specific attention is paid to the influence of process variables in Friction Stir Welding on the wear process characterizes the effect of process parameters (spindle speed, traverse rate, and length of joint) on the wear process. A phenomenological model of the wear process was constructed based on the rotating plug model of Friction Stir Welding. The effectiveness of harder tool materials (such as Tungsten Carbide, high speed steel, and tools with diamond coatings) to combat abrasive wear is also explored. In-process force, torque, and vibration signals are analyzed to assess the feasibility of in situ monitoring of tool shape changes as a result of wear (an advancement which would eliminate the need for off-line evaluation of tool condition during joining). Monitoring, controlling, and reducing tool wear in FSW of MMCs is essential to implementation of these materials in structures (such as launch vehicles) where they would be of maximum benefit. The work presented here is extendable to machining of MMCs, where wear of the tool is also a limiting factor.

Joining and Integration of Silicon Carbide for Turbine Engine Applications

NASA Technical Reports Server (NTRS)

Halbig, Michael C.; Singh, Mrityunjay; Coddington, Bryan; Asthana, Rajiv

2010-01-01

The critical need for ceramic joining and integration technologies is becoming better appreciated as the maturity level increases for turbine engine components fabricated from ceramic and ceramic matrix composite materials. Ceramic components offer higher operating temperatures and reduced cooling requirements. This translates into higher efficiencies and lower emissions. For fabricating complex shapes, diffusion bonding of silicon carbide (SiC) to SiC is being developed. For the integration of ceramic parts to the surrounding metallic engine system, brazing of SiC to metals is being developed. Overcoming the chemical, thermal, and mechanical incompatibilities between dissimilar materials is very challenging. This presentation will discuss the types of ceramic components being developed by researchers and industry and the benefits of using ceramic components. Also, the development of strong, crack-free, stable bonds will be discussed. The challenges and progress in developing joining and integration approaches for a specific application, i.e. a SiC injector, will be presented.

Private Security Contractors: A Way of Combating Piracy in the Horn of Africa

DTIC Science & Technology

2014-05-22

September 2011. 79Financial Action Task Force, “Financial Action Task Force Annual Report, 2010-2011,” FATF /OECD, 2011, 10. 80Andrew J. Shapiro...Report, 2010-2011.” FATF /OECD. Paris, 2011. Fox News. “Private Security Firms Join Battle Against Somali Pirates,” October 26, 2008. http

3 CFR 8976 - Proclamation 8976 of May 9, 2013. Military Spouse Appreciation Day, 2013

Code of Federal Regulations, 2014 CFR

2014-01-01

... wounded warriors. America's military spouses are at the core of our Armed Forces, and on Military Spouse..., 2013 Proc. 8976 Military Spouse Appreciation Day, 2013By the President of the United States of America... for military homeowners. Through First Lady Michelle Obama and Dr. Jill Biden's Joining Forces...

Building An Adaptive Cyber Strategy

DTIC Science & Technology

2016-06-01

forces. The primary mission of the military in any domain, including cyber , should be readiness to exert force if needed during crisis . AU/ACSC/SMITH...of crisis . The military must be able to AU/ACSC/SMITH, FI/AY16 manipulate the cyber environment, but should avoid direct use of force against...operations focus on maintaining a manageable threat level. Cyberspace is a continually evolving domain, and nations throughout the world can join in cyber

Releasable locking mechanisms

NASA Technical Reports Server (NTRS)

Ahmed, Rafiq (Inventor); Wingate, Robert J. (Inventor)

2005-01-01

In the aerospace field spacecraft components are held together by separation systems until a specific time when they must be separated or deployed. Customarily a threaded joining bolt engages one of the components to be joined, and a threaded nut is placed on that bolt against the other component so they can be drawn together by a releasable locking assembly. The releasable locking assembly herein includes a plunger having one end coupled to one end of a plunger bolt. The other end is flanged to abut and compress a coil spring when the plunger is advanced toward the interface plane between the two components. When the plunger is so advanced toward the interface plane, the end of the plunger bolt can be connected to the joining bolt. Thus during retraction the joining bolt is drawn to one side of the interface plane by the force of the expanding spring.

Releasable Locking Mechanisms

NASA Technical Reports Server (NTRS)

Ahmed, Rafiq (Inventor); Wingate, Robert J. (Inventor)

2005-01-01

In the aerospace field spacecraft components are held together by separation systems until a specific time when they must be separated or deployed. Customarily a threaded joining bolt engages one of the components to be joined, and a threaded nut is placed on that bolt against the other component so they can be drawn together by a releasable locking assembly. The releasable locking assembly herein includes a plunger having one end coupled to one end of a plunger bolt. The other end is flanged to abut and compress a coil spring when the plunger is advanced toward the interface plane between the two components. When the plunger is so advanced toward the interface plane, the end of the plunger bolt can be connected to the joining bolt. Thus during retraction the joining bolt is drawn to one side of the interface plane by the force of the expanding spring.

Example of a Participant Agreement for the Food Recovery Challenge

EPA Pesticide Factsheets

This page contains an example of the participant agreement from the Sustainable Materials Management database system for anyone thinking about joining the Food Recovery Challenge can view to learn about what it entails.

Race to the Top - Early Learning Challenge: 2014 Annual Performance Report Kentucky

ERIC Educational Resources Information Center

Race to the Top - Early Learning Challenge, 2015

2015-01-01

This Race to the Top - Early Learning Challenge (RTT-ELC) annual performance report for the year 2014 describes Kentucky's accomplishments, lessons learned, challenges, and strategies Kentucky will implement to address those challenges. In December of 2013, Kentucky received notice that they would join 19 other States as a winner of the Race to…

Joining Forces: The Chemical Biology-Medicinal Chemistry Continuum.

PubMed

Plowright, Alleyn T; Ottmann, Christian; Arkin, Michelle; Auberson, Yves P; Timmerman, Henk; Waldmann, Herbert

2017-09-21

The scientific advances being made across all disciplines are creating ever-increasing opportunities to enhance our knowledge of biological systems and how they relate to human disease. One of the central driving forces in discovering new medicines is medicinal chemistry, where the design and synthesis of novel compounds has led to multiple drugs. Chemical biology, sitting at the interface of many disciplines, has now emerged as a major contributor to the understanding of biological systems and is becoming an integral part of drug discovery. Bringing chemistry and biology much closer and blurring the boundaries between disciplines is creating new opportunities to probe and understand biology; both disciplines play key roles and need to join forces and work together effectively to synergize their impact. The power of chemical biology will then reach its full potential and drive innovation, leading to the discovery of transformative medicines to treat patients. Advances in cancer biology and drug discovery highlight this potential. Copyright © 2017 Elsevier Ltd. All rights reserved.

Becoming Cruel: Appetitive Aggression Released by Detrimental Socialisation in Former Congolese Soldiers

ERIC Educational Resources Information Center

Weierstall, Roland; Haer, Roos; Banholzer, Lilli; Elbert, Thomas

2013-01-01

Appetitive aggression--a rewarding perception of the perpetration of violence--seems to be an adaptation common to adverse conditions. Children raised within armed groups may develop attitudes and values that favour harming others when socialized within a combat force. Combatants who joined an armed force early in their lives should, therefore,…

Laser hybrid joining of plastic and metal components for lightweight components

NASA Astrophysics Data System (ADS)

Rauschenberger, J.; Cenigaonaindia, A.; Keseberg, J.; Vogler, D.; Gubler, U.; Liébana, F.

2015-03-01

Plastic-metal hybrids are replacing all-metal structures in the automotive, aerospace and other industries at an accelerated rate. The trend towards lightweight construction increasingly demands the usage of polymer components in drive trains, car bodies, gaskets and other applications. However, laser joining of polymers to metals presents significantly greater challenges compared with standard welding processes. We present recent advances in laser hybrid joining processes. Firstly, several metal pre-structuring methods, including selective laser melting (SLM) are characterized and their ability to provide undercut structures in the metal assessed. Secondly, process parameter ranges for hybrid joining of a number of metals (steel, stainless steel, etc.) and polymers (MABS, PA6.6-GF35, PC, PP) are given. Both transmission and direct laser joining processes are presented. Optical heads and clamping devices specifically tailored to the hybrid joining process are introduced. Extensive lap-shear test results are shown that demonstrate that joint strengths exceeding the base material strength (cohesive failure) can be reached with metal-polymer joining. Weathering test series prove that such joints are able to withstand environmental influences typical in targeted fields of application. The obtained results pave the way toward implementing metalpolymer joints in manufacturing processes.

Systematic and Automated Development of Quantum Mechanically Derived Force Fields: The Challenging Case of Halogenated Hydrocarbons.

PubMed

Prampolini, Giacomo; Campetella, Marco; De Mitri, Nicola; Livotto, Paolo Roberto; Cacelli, Ivo

2016-11-08

A robust and automated protocol for the derivation of sound force field parameters, suitable for condensed-phase classical simulations, is here tested and validated on several halogenated hydrocarbons, a class of compounds for which standard force fields have often been reported to deliver rather inaccurate performances. The major strength of the proposed protocol is that all of the parameters are derived only from first principles because all of the information required is retrieved from quantum mechanical data, purposely computed for the investigated molecule. This a priori parametrization is carried out separately for the intra- and intermolecular contributions to the force fields, respectively exploiting the Joyce and Picky programs, previously developed in our group. To avoid high computational costs, all quantum mechanical calculations were performed exploiting the density functional theory. Because the choice of the functional is known to be crucial for the description of the intermolecular interactions, a specific procedure is proposed, which allows for a reliable benchmark of different functionals against higher-level data. The intramolecular and intermolecular contribution are eventually joined together, and the resulting quantum mechanically derived force field is thereafter employed in lengthy molecular dynamics simulations to compute several thermodynamic properties that characterize the resulting bulk phase. The accuracy of the proposed parametrization protocol is finally validated by comparing the computed macroscopic observables with the available experimental counterparts. It is found that, on average, the proposed approach is capable of yielding a consistent description of the investigated set, often outperforming the literature standard force fields, or at least delivering results of similar accuracy.

Who joins the network? Physicians' resistance to take budgetary co-responsibility.

PubMed

Rischatsch, Maurus

2015-03-01

Managed Care (MC) is expected to provide health care at a lower cost than conventional provision. Therefore, Switzerland intends to promote MC by forcing health insurers to write MC contracts and introducing budgetary co-responsibility for ambulatory care physicians. A discrete choice experiment conducted in 2011 including 872 physicians reveals a strong preference heterogeneity with respect to network participation and alternative remuneration schemes. The number of physicians working in networks is unlikely to rise on a voluntary basis, while general practitioners are more likely to join networks than specialists with surgical activities. For physicians considering joining networks, cost savings are predicted to be higher than the estimated willingness-to-accept payments. Copyright © 2014 Elsevier B.V. All rights reserved.

Integrative research on environmental and landscape change: PhD students' motivations and challenges.

PubMed

Tress, Bärbel; Tress, Gunther; Fry, Gary

2009-07-01

The growing demand for integrative (interdisciplinary or transdisciplinary) approaches in the field of environmental and landscape change has increased the number of PhD students working in this area. Yet, the motivations to join integrative projects and the challenges for PhD students have so far not been investigated. The aims of this paper were to identify the understanding of PhD students with regard to integrative research, their motivations to join integrative projects, their expectations in terms of integration and results, and to reveal the challenges they face in integrative projects. We collected data by a questionnaire survey of 104 PhD students attending five PhD Master Classes held from 2003 to 2006. We used manual content analysis to analyse the free-text answers. The results revealed that students lack a differentiated understanding of integrative approaches. The main motivations to join integrative projects were the dissertation subject, the practical relevance of the project, the intellectual stimulation of working with different disciplines, and the belief that integrative research is more innovative. Expectations in terms of integration were high. Core challenges for integration included intellectual and external challenges such as lack of knowledge of other disciplines, knowledge transfer, reaching depth, supervision, lack of exchange with other students and time demands. To improve the situation for PhD students, we suggest improving knowledge on integrative approaches, balancing practical applicability with theoretical advancement, providing formal introductions to other fields of research, and enhancing institutional support for integrative PhD projects.

Tiffany Byrne | NREL

Science.gov Websites

include meeting planning and travel processing. Prior to joining NREL, Tiffany led the travel department at the NASA Armstrong Flight Research Center at Edwards Air Force Base in California, where she

Advanced Metalworking Solutions For Naval Systems That Go In Harm’s Way

DTIC Science & Technology

2015-01-01

destroyers USS Momsen (DDG 92) and USS Preble (DDG 88) are underway in formation. U.S. Navy photo Front cover: Ingalls Shipbuilding welding photo...applies a variety of innovative welding technologies to address the challenges associated with joining weapon system components. Joining Technologies...friction stir welding process to manufacture edge-cooled naval electronic cold plate assemblies. The modular, high- performance, and scalable

Astronaut Crippen prepares to join crew in training

NASA Image and Video Library

1984-09-04

41D-3186 (4 Sept 1984) --- Astronaut Robert L. Crippen, 41-G crew commander, prepares to join his six fellow crewmembers for some training in the mockup and integration laboratory at the Johnson Space Center. Astronaut David C. Leestma, 41-G mission specialist, left, will participate in a scheduled extravehicular activity (EVA) on the Challenger's next mission. Today's training is for launch phase procedures.

Joining Forces with the Arts Community.

ERIC Educational Resources Information Center

Wenner, Gene C.

1988-01-01

Proposes how music educators and arts administrators can work together to improve arts education. Recommends development of lobbying groups, and suggests ways of forming community attitudes to increase support for arts education. (LS)

Allied against reform: pharmaceutical industry-academic physician relations in the United States, 1945-1970.

PubMed

Tobbell, Dominique A

2008-01-01

During the 1960s, the drug industry was the subject of two congressional investigations into its business practices and pricing policies, and in 1962, passage of the Drug Amendments mandated greater Food and Drug Administration authority over pharmaceutical development. In this article, I examine the industry's efforts to circumvent these political challenges by drawing on its longstanding relationship with academic physicians and the American Medical Association. Using the medical profession's shared concern about expanding government oversight over therapeutic practice, the industry called on academic physicians to join forces with it and establish an expert advisory body to guide government officials on pharmaceutical policy. Drawing on research in the archives of the University of Pennsylvania and the National Academy of Sciences and a careful reading of the trade and biomedical literature and congressional documents, I argue that by positioning themselves as pharmaceutical experts, the members of this industry-academic alliance gave industry a seat at the policy table and enabled it to challenge the efforts of pharmaceutical reformers to further increase the government's role in drug development.

Partnerships: One Strategy for Meeting Big Data Challenges

NASA Astrophysics Data System (ADS)

Chandler, C. L.; Groman, R. C.; Kinkade, D.; Shepherd, A.; Allison, M. D.; Rauch, S.; Wiebe, P. H.; Glover, D. M.

2014-12-01

In late 2006 staff members from the previously independent US Joint Global Ocean Flux Study (US JGOFS) and US GLOBal Ocean ECosystems Dynamics (US GLOBEC) data management offices joined forces and received funding from the US National Science Foundation to provide data management support to ocean science researchers. The transition from providing dedicated, project-specific data management services to supporting a broader research community data facility has necessitated understanding of and adaptation to evolving needs. One of the strategies that has proven to be very effective is the formation of partnerships with other groups doing complementary work. Staff members at BCO-DMO have formed collaborative partnerships with others to support our primary research community efficiently and in a way that covers the full research data life cycle. Examples will be provided that highlight ways in which such partnerships have enhanced the work done by BCO-DMO, and also ways in which BCO-DMO activities have contributed to broader national and global initiatives. One of the clear benefits of collaboration with other groups is the opportunity for identification of shared challenges, strategies and solutions and the increased likelihood of developing interoperable systems.

Effects of process parameters on friction self-piercing riveting of dissimilar materials

DOE PAGES

Liu, Xun; Lim, Yong Chae; Li, Yongbing; ...

2016-05-24

In the present work, a recently developed solid state joining technique, Friction self-piercing riveting (F-SPR), has been applied for joining high strength aluminum alloy AA7075-T6 to magnesium alloy AZ31B. The process was performed on a specially designed machine where the spindle can achieve the motion of sudden stop. Effects of rivet rotating rate and punch speed on axial plunge force, torque, joint microstructure and quality have been analyzed systematically. During F-SPR, higher rotating rate and slower punch speed can reduce axial force and torque, which correspondingly results in a slightly smaller interlock between rivet leg and joined materials. Improved localmore » flowability of both aluminum and magnesium alloys under a higher rotating speed results in a thicker aluminum layer surrounding the rivet leg, where formation of Al-Mg intermetallics was observed. Equivalent joint strength obtained in this study are higher than the yield strength of the AZ31 Mg alloy. One of the tensile failure modes is the rivet fracture, which is due to local softening of rivet leg from frictional heat. Lastly, other two failure modes include rivet pullout and shear through of bottom sheet.« less

SALMON 2100 PROJECT

EPA Science Inventory

Twenty eight salmon scientists and policy experts have joined forces in an innovative project to identify ways that, if adopted, likely would restore and sustain wild salmon runs in California, Oregon, Washington, Idaho, and southern British Columbia.

Serial elastic elements in the damselfly wing: mobile vein joints contain resilin

PubMed

Gorb

1999-11-01

Two main types of joints occur in the damselfly wing: mobile and immobile. Some longitudinal veins (RP2(-), RP3&4(-), and MP(-)) are elastically joined with cross veins, whereas other longitudinal veins (IR1(+), IR2(+), MA(+), CuA'(+)) are firmly joined with cross veins. In this study we mapped the distribution of serial elastic elements in the wing. The occurrence of resilin, a rubberlike protein, in mobile joints suggests that the automatic twisting mechanism of the leading edge by aerodynamic force works not by flexibility but by the elasticity of these joints. First, it should result in elastic energy storage in the distal areas of the wing. Second, serial elastic elements of wing presumably act as dampers of an aerodynamic force, which are responsible for gradual twisting of the leading edge.

Serial Elastic Elements in the Damselfly Wing: Mobile Vein Joints Contain Resilin

NASA Astrophysics Data System (ADS)

Gorb, Stanislav N.

Two main types of joints occur in the damselfly wing: mobile and immobile. Some longitudinal veins (RP2-, RP3&4-, and MP-) are elastically joined with cross veins, whereas other longitudinal veins (IR1+, IR2+, MA+, CuA'+) are firmly joined with cross veins. In this study we mapped the distribution of serial elastic elements in the wing. The occurrence of resilin, a rubberlike protein, in mobile joints suggests that the automatic twisting mechanism of the leading edge by aerodynamic force works not by flexibility but by the elasticity of these joints. First, it should result in elastic energy storage in the distal areas of the wing. Second, serial elastic elements of wing presumably act as dampers of an aerodynamic force, which are responsible for gradual twisting of the leading edge.

State-of-technology for joining TD-NiCr sheet.

NASA Technical Reports Server (NTRS)

Holko, K. H.; Moore, T. J.; Gyorgak, C. A.

1972-01-01

At the current state-of-technology there are many joining processes that can be used to make sound welds in TD-NiCr sheet. Some of these that are described in this report are electron beam welding (EBW), gas-tungsten arc welding (GTAW), diffusion welding (DFW), resistance spot welding (RSW), resistance seam welding (RSEW), and brazing. Roll welding (RW) and explosion welding (EXW) have not been developed to the point where they can be used to make sound welds in TD-NiCr. Joining work that has previously been done on TD-NiCr by various organizations, both privately supported and under Air Force and NASA contracts, is described in this summary. Current work is also described that is being done at General Dynamics/Convair (under NASA contract) and at NASA/Lewis to develop and evaluate DFW, RSW, RSEW, and brazing. Preliminary comparisons of joining processes are made for typical applications. A brief description of the manufacture of TD-NiCr sheet by a recently standardized process (under NASA contract) also is given.

Joining and Assembly of Silicon Carbide-based Advanced Ceramics and Composites for High Temperature Applications

NASA Technical Reports Server (NTRS)

Singh, M.

2004-01-01

Silicon carbide based advanced ceramics and fiber reinforced composites are under active consideration for use in wide variety of high temperature applications within the aeronautics, space transportation, energy, and nuclear industries. The engineering designs of ceramic and composite component require fabrication and manufacturing of large and complex shaped parts of various thicknesses. In many instances, it is more economical to build up complex shapes by joining simple geometrical shapes. In addition these components have to be joined or assembled with metallic sub-components. Thus, joining and attachment have been recognized as enabling technologies for successful utilization of ceramic components in various demanding applications. In this presentation, various challenges and opportunities in design, fabrication, and testing o high temperature joints in ceramic matrix composites will be presented. Silicon carbide based advanced ceramics (CVD and hot pressed), and C/SiC and SiC/SiC composites, in different shapes and sizes, have been joined using an affordable, robust ceramic joining technology (ARCJoinT). Microstructure and high temperature mechanical properties of joints in silicon carbide ceramics and CVI and melt infiltrated SiC matrix composites will,be reported. Various joint design philosophies and design issues in joining of ceramics and composites well be discussed.

An Investigation of the Effects of Rank, AFSC, and Dependents on the Length of the Separation for Air Force Enlisted Join Spouse Couples.

DTIC Science & Technology

1985-12-01

whether they have dependents? This research effort will attempt to answer these questions. The specific objectives of this research effort will be to apply ...not centered on military join spouse couples, but man’ of their findings apply to couples from all walks of life where both the husband and wife are...these three techniques, the hypotheses which were tested during the research effort and the assumptions under which they apply are also covered in this

Tube swaging device uses explosive force

NASA Technical Reports Server (NTRS)

Mc Smith, D. G.

1968-01-01

Tool joins a sleeve to a tube by explosive swaging, thus providing a leakproof, lightweight, and strong assembly. No new or different material is used in this method and therefore the thermal and galvanic properties are maintained.

Cattle tick vaccine researchers join forces in CATVAC.

PubMed

Schetters, Theo; Bishop, Richard; Crampton, Michael; Kopáček, Petr; Lew-Tabor, Alicja; Maritz-Olivier, Christine; Miller, Robert; Mosqueda, Juan; Patarroyo, Joaquín; Rodriguez-Valle, Manuel; Scoles, Glen A; de la Fuente, José

2016-02-24

A meeting sponsored by the Bill & Melinda Gates Foundation was held at the Avanti Hotel, Mohammedia, Morocco, July 14-15, 2015. The meeting resulted in the formation of the Cattle Tick Vaccine Consortium (CATVAC).

Cattle tick vaccine researchers join forces in CATVAC

USDA-ARS?s Scientific Manuscript database

A meeting sponsored by the Bill & Melinda Gates Foundation was held at the Avanti Hotel, Mohammedia, Morocco, July 14–15, 2015. The meeting resulted in the formation of the Cattle Tick Vaccine Consortium (CATVAC)....

Air Force Commander’s Guide to Diversity and Inclusion

DTIC Science & Technology

2015-01-01

diversity: differences in styles of work, thinking, learning , and personality ■ organizational/structural diversity: organizational/ institutional...leadership roles themselves, or inspire youth from different backgrounds to join. Research shows that organizations must lead to reap diversity’s benefits...Greatest Air Force,’ but to remain so, we must learn to be comprehensively inclusive, throughout our ranks, and throughout our specialties. If we

Industrial shifts, female employment, and occupational differentiation: a dynamic model for American cities, 1960-1970.

PubMed

Semyonov, M; Scott, R I

1983-05-01

Sex-linked occupational differentiation has been seen as influenced by both the industrial structure of the economy and the sex composition of the labor force. Here, with a sample of 70 SMSAs, it was found (a) that the odds of men relative to women of joining professional and managerial occupations increased between 1960 and 1970, and (b) that this increase was dependent on the growth of tertiary industries and the greater number of women joining the cash economy. The observed effect of industrial shifts on sex-occupational differentiation, however, is argued to be a spurious consequence of the gender-composition of the work force. Specifically, the development of tertiary industries generates greater demand for female labor. Intensive recruitment of women to the labor force in turn increases occupational differentiation because females, in sex-typed labor markets, are likely to be channeled in disproportionate numbers away from upper-status occupations. The findings demonstrate that traditional modernization theory is unable to account for this. However, the results lend support to expectations derived from a labor market sex-segmentation approach.

Multisociety Task Force for Critical Care Research: key issues and recommendations.

PubMed

Deutschman, Clifford S; Ahrens, Tom; Cairns, Charles B; Sessler, Curtis N; Parsons, Polly E

2012-01-01

Research in critical care extends from the bench to the bedside, involving multiple departments, specialties, and funding organizations. Because of this diversity, it has been difficult for all stakeholders to collectively identify challenges and establish priorities. To define a comprehensive agenda for critical care research using input from a broad range of stakeholders to serve as a blueprint for future initiatives. The Critical Care Societies Collaborative (CCSC), consisting of the leadership of the American Association of Critical-Care Nurses (AACN), the American College of Chest Physicians (ACCP), the American Thoracic Society (ATS), and the Society of Critical Care Medicine (SCCM), joined the US Critical Illness and Injury Trials Group (USCIITG) in forming a task force to define a comprehensive critical care research agenda. This group of 25 identified experts was divided into subgroups to address basic, translational, clinical, implementation, and educational research. The subgroups met via conference calls, and the entire task force met in person for a 2-day session. The result was a detailed discussion of the research priorities that served as the basis for this report. The task force identified challenges, specific priority areas, and recommendations for process improvements to support critical care research. Additionally, four overarching themes emerged: 1) the traditional "silo-ed" approach to critical care research is counterproductive and should be modified; 2) an approach that more effectively links areas of research (i.e., basic and translational research, or clinical research and implementation) should be embraced; 3) future approaches to human research should account for disease complexity and patient heterogeneity; and 4) an enhanced infrastructure for critical care research is essential for future success. This document contains the themes/recommendations developed by a large, multiprofessional cross section of critical care scientists, clinicians, and educators. It provides a unique framework for future research in critical care medicine.

Multisociety task force for critical care research: key issues and recommendations.

PubMed

Deutschman, Clifford S; Ahrens, Tom; Cairns, Charles B; Sessler, Curtis N; Parsons, Polly E

2012-01-01

Research in critical care extends from the bench to the bedside, involving multiple departments, specialties, and funding organizations. Because of this diversity, it has been difficult for all stakeholders to collectively identify challenges and establish priorities. To define a comprehensive agenda for critical care research using input from a broad range of stakeholders to serve as a blueprint for future initiatives. The Critical Care Societies Collaborative (CCSC), consisting of the leadership of the American Association of Critical-Care Nurses (AACN), the American College of Chest Physicians (ACCP), the American Thoracic Society (ATS), and the Society of Critical Care Medicine (SCCM), joined the U.S. Critical Illness and Injury Trials Group (USCIITG) in forming a task force to define a comprehensive critical care research agenda. This group of 25 identified experts was divided into subgroups to address basic, translational, clinical, implementation, and educational research. The subgroups met via conference calls, and the entire task force met in person for a 2-day session. The result was a detailed discussion of the research priorities that served as the basis for this report. The task force identified challenges, specific priority areas, and recommendations for process improvements to support critical care research. Additionally, four overarching themes emerged: (1) the traditional "silo-ed" approach to critical care research is counterproductive and should be modified; (2) an approach that more effectively links areas of research (i.e., basic and translational research, or clinical research and implementation) should be embraced; (3) future approaches to human research should account for disease complexity and patient heterogeneity; and (4) an enhanced infrastructure for critical care research is essential for future success. This document contains the themes/recommendations developed by a large, multiprofessional cross-section of critical care scientists, clinicians, and educators. It provides a unique framework for future research in critical care medicine.

Multisociety task force for critical care research: key issues and recommendations.

PubMed

Deutschman, Clifford S; Ahrens, Tom; Cairns, Charles B; Sessler, Curtis N; Parsons, Polly E

2012-01-01

Research in critical care extends from the bench to the bedside, involving multiple departments, specialties, and funding organizations. Because of this diversity, it has been difficult for all stakeholders to collectively identify challenges and establish priorities. To define a comprehensive agenda for critical care research using input from a broad range of stakeholders to serve as a blueprint for future initiatives. The Critical Care Societies Collaborative (CCSC), consisting of the leadership of the American Association of Critical-Care Nurses (AACN), the American College of Chest Physicians (ACCP), the American Thoracic Society (ATS), and the Society of Critical Care Medicine (SCCM), joined the US Critical Illness and Injury Trials Group (USCIITG) in forming a task force to define a comprehensive critical care research agenda. This group of 25 identified experts was divided into subgroups to address basic, translational, clinical, implementation, and educational research. The subgroups met via conference calls, and the entire task force met in person for a 2-day session. The result was a detailed discussion of the research priorities that served as the basis for this report. The task force identified challenges, specific priority areas, and recommendations for process improvements to support critical care research. Additionally, four overarching themes emerged: 1) the traditional "silo-ed" approach to critical care research is counterproductive and should be modified; 2) an approach that more effectively links areas of research (ie, basic and translational research, or clinical research and implementation) should be embraced; 3) future approaches to human research should account for disease complexity and patient heterogeneity; and 4) an enhanced infrastructure for critical care research is essential for future success. This document contains the themes/recommendations developed by a large, multiprofessional cross section of critical care scientists, clinicians, and educators. It provides a unique framework for future research in critical care medicine.

Multisociety Task Force for Critical Care Research: Key Issues and Recommendations

PubMed Central

Deutschman, Clifford S.; Ahrens, Tom; Cairns, Charles B.; Sessler, Curtis N.; Parsons, Polly E.

2012-01-01

Background: Research in critical care extends from the bench to the bedside, involving multiple departments, specialties, and funding organizations. Because of this diversity, it has been difficult for all stakeholders to collectively identify challenges and establish priorities. Objective: To define a comprehensive agenda for critical care research using input from a broad range of stakeholders to serve as a blueprint for future initiatives. Methods: The Critical Care Societies Collaborative (CCSC), consisting of the leadership of the American Association of Critical-Care Nurses (AACN), the American College of Chest Physicians (ACCP), the American Thoracic Society (ATS), and the Society of Critical Care Medicine (SCCM), joined the U.S. Critical Illness and Injury Trials Group (USCIITG) in forming a task force to define a comprehensive critical care research agenda. This group of 25 identified experts was divided into subgroups to address basic, translational, clinical, implementation, and educational research. The subgroups met via conference calls, and the entire task force met in person for a 2-day session. The result was a detailed discussion of the research priorities that served as the basis for this report. Results: The task force identified challenges, specific priority areas, and recommendations for process improvements to support critical care research. Additionally, four overarching themes emerged: (1) the traditional “silo-ed” approach to critical care research is counterproductive and should be modified; (2) an approach that more effectively links areas of research (i.e., basic and translational research, or clinical research and implementation) should be embraced; (3) future approaches to human research should account for disease complexity and patient heterogeneity; and (4) an enhanced infrastructure for critical care research is essential for future success. Conclusions: This document contains the themes/recommendations developed by a large, multiprofessional cross-section of critical care scientists, clinicians, and educators. It provides a unique framework for future research in critical care medicine. PMID:22210788

Multisociety Task Force for Critical Care Research

PubMed Central

Deutschman, Clifford S.; Ahrens, Tom; Cairns, Charles B.; Sessler, Curtis N.

2012-01-01

Background: Research in critical care extends from the bench to the bedside, involving multiple departments, specialties, and funding organizations. Because of this diversity, it has been difficult for all stakeholders to collectively identify challenges and establish priorities. Objective: To define a comprehensive agenda for critical care research using input from a broad range of stakeholders to serve as a blueprint for future initiatives. Methods: The Critical Care Societies Collaborative (CCSC), consisting of the leadership of the American Association of Critical-Care Nurses (AACN), the American College of Chest Physicians (ACCP), the American Thoracic Society (ATS), and the Society of Critical Care Medicine (SCCM), joined the US Critical Illness and Injury Trials Group (USCIITG) in forming a task force to define a comprehensive critical care research agenda. This group of 25 identified experts was divided into subgroups to address basic, translational, clinical, implementation, and educational research. The subgroups met via conference calls, and the entire task force met in person for a 2-day session. The result was a detailed discussion of the research priorities that served as the basis for this report. Results: The task force identified challenges, specific priority areas, and recommendations for process improvements to support critical care research. Additionally, four overarching themes emerged: 1) the traditional “silo-ed” approach to critical care research is counterproductive and should be modified; 2) an approach that more effectively links areas of research (ie, basic and translational research, or clinical research and implementation) should be embraced; 3) future approaches to human research should account for disease complexity and patient heterogeneity; and 4) an enhanced infrastructure for critical care research is essential for future success. Conclusions: This document contains the themes/recommendations developed by a large, multiprofessional cross section of critical care scientists, clinicians, and educators. It provides a unique framework for future research in critical care medicine. PMID:22215828

Welding blades to rotors

NASA Technical Reports Server (NTRS)

Hoklo, K. H.; Moore, T. J. (Inventor)

1973-01-01

A process is described to form T-joints between dissimilar thickness parts by magnetic force upset welding. This type of resistance welding is used to join compressor and turbine parts which thereby reduces the weight and cost of jet engines.

Ethics, A Choice for the Future: An Interdisciplinary Program.

ERIC Educational Resources Information Center

Downie, Susan L.

1989-01-01

Describes an interdisciplinary program in which English, social studies, physics, and calculus teachers joined forces to teach high school students critical-thinking skills so that students could make ethical decisions and solve ethical dilemmas. (MM)

Developing for the future: hometown USA.

DOT National Transportation Integrated Search

2000-09-01

In a trend that continues to build, citizens : across the country are joining forces locally to : address environmental issues that affect their : health, natural resources, and the quality of : life in their communities. Groups of people are : takin...

Uniting of NuSTAR Spacecraft and Rocket

NASA Image and Video Library

2012-02-23

Inside an environmental enclosure at Vandenberg Air Force Base processing facility in California, solar panels line the sides of NASA Nuclear Spectroscopic Telescope Array NuSTAR, which was just joined to the Orbital Sciences Pegasus XL rocket.

Ultrashort pulse laser micro-welding of cyclo-olefin copolymers

NASA Astrophysics Data System (ADS)

Roth, Gian-Luca; Rung, Stefan; Hellmann, Ralf

2017-06-01

We report on the joining of transparent thermoplastic polymers using infrared femtosecond laser pulses. Due to nonlinear absorption, the developed micro-welding process for cyclo-olefin copolymers does not require any intermediate absorbing layers or any surface pre-processing of the welding partners. In view of an optimized and stable micro-welding process, the influence of the welding speed and focal position on both, the quality and shear force strength are investigated. We highlight that welding seam widths of down to 65 μm are feasible for welding speeds of up to 75 mm/s. However, a variation of the welding speed affects the required focal position for a successful joining process. The shear force strength of the welding seam is determined to 37 MPa, which corresponds to 64% of the shear strength of the bulk material and is not affected by the welding speed.

Advances in Solid State Joining of High Temperature Alloys

NASA Technical Reports Server (NTRS)

Ding, Jeff; Schneider, Judy

2011-01-01

Many of the metals used in the oil and gas industry are difficult to fusion weld including Titanium and its alloys. Solid state joining processes are being pursued as an alternative process to produce robust structures more amenable to high pressure applications. Various solid state joining processes include friction stir welding (FSW) and a patented modification termed thermal stir welding (TSW). The configuration of TSWing utilizes an induction coil to preheat the material minimizing the burden on the weld tool extending its life. This provides the ability to precisely select and control the temperature to avoid detrimental changes to the microstructure. The work presented in this presentation investigates the feasibility of joining various titanium alloys using the solid state welding processes of FSW and TSW. Process descriptions and attributes of each weld process will be presented. Weld process set ]up and welding techniques will be discussed leading to the challenges experienced. Mechanical property data will also be presented.

The practice of mediation to resolve clinical, bioethical, and medical malpractice disputes.

PubMed

Lee, Danny W H; Lai, Paul B S

2015-12-01

Mediation is a voluntary process whereby a neutral and impartial third party-t-he mediator--is present to facilitate communication and negotiation between the disputing parties so that amicable settlements can be agreed. Being confidential and non-adversarial in nature, the mediation process and skills are particularly applicable in clinical practice to facilitate challenging communications following adverse events, to assist bioethical decision making and to resolve disputes. Mediation is also a more effective and efficient means of dispute resolution in medical malpractice claims when compared with civil litigation. Health care mediation teams should be set up at individual facilities to provide education and consultation services to frontline staff and patients. At a community level, the Government, the mediation community, and the health care professionals should join forces to promote mediation as a means to settle medical malpractice claims outside of the courtroom.

Nineteenth-century urbanization as sacred process: insights from German Strasbourg.

PubMed

Steinhoff, Anthony J

2011-01-01

This article examines a crucial site for modernity’s encounter with religion during the long nineteenth century, albeit one largely ignored both by religious and urban historians: the modern big city. Drawing on evidence from Strasbourg, which joined the ranks of Germany’s big cities soon after the Franco-Prussian War, it points out first, that urbanization had a significant urban dimension. It altered the absolute and relative size of the city’s faith communities, affected the confessional composition of urban neighborhoods, and prompted faith communities to mark additional parts of the urban landscape as sacred. Second, while urban growth—both demographic and physical—frequently challenged traditional understandings of religious community, it also facilitated the construction of new understandings of piety and community, especially via voluntary organizations and the religious media. Thereby, urbanization emerged as a key force behind sacralization in city and countryside as the nineteenth century ended and the twentieth began.

Ultrasonic Low-Friction Containment Plate for Thermal and Ultrasonic Stir Weld Processes

NASA Technical Reports Server (NTRS)

Graff, Karl; Short, Matt

2013-01-01

The thermal stir welding (TSW) process is finding applications in fabrication of space vehicles. In this process, workpieces to be joined by TSW are drawn, by heavy forces, between "containment plates," past the TSW tool that then causes joining of the separate plates. It is believed that the TSW process would be significantly improved by reducing the draw force, and that this could be achieved by reducing the friction forces between the workpieces and containment plates. Based on use of high-power ultrasonics in metal forming processes, where friction reduction in drawing dies has been achieved, it is believed that ultrasonic vibrations of the containment plates could achieve similar friction reduction in the TSW process. By applying ultrasonic vibrations to the containment plates in a longitudinal vibration mode, as well as by mounting and holding the containment plates in a specific manner such as to permit the plates to acoustically float, friction between the metal parts and the containment plates is greatly reduced, and so is the drawing force. The concept was to bring in the ultrasonics from the sides of the plates, permitting the ultrasonic hardware to be placed to the side, away from the equipment that contains the thermal stir tooling and that applies clamping forces to the plates. Tests demonstrated that one of the major objectives of applying ultrasonics to the thermal stir system, that of reducing draw force friction, should be achievable on a scaled-up system.

Sustainable Management of Food

EPA Pesticide Factsheets

To provide information to organizations to help them implement sustainable food management, including joining the Food Recovery Challenge. To provide education and information to communities and concerned citizens.

37th Training Wing > Units > Inter-American Air Forces Academy

Science.gov Websites

37th Training Wing 37th Training Wing Join the Air Force Home News Commentaries Features Photos Art Information CAC/ID Card Information Units 37th Training Group 341st Training Squadron 344th Training Squadron 37th Training Wing Staff Agency 737th Training Group Defense Language Institute English Language Center

Joining and Integration of Silicon Carbide-Based Materials for High Temperature Applications

NASA Technical Reports Server (NTRS)

Halbig, Michael C.; Singh, Mrityunjay

2016-01-01

Advanced joining and integration technologies of silicon carbide-based ceramics and ceramic matrix composites are enabling for their implementation into wide scale aerospace and ground-based applications. The robust joining and integration technologies allow for large and complex shapes to be fabricated and integrated with the larger system. Potential aerospace applications include lean-direct fuel injectors, thermal actuators, turbine vanes, blades, shrouds, combustor liners and other hot section components. Ground based applications include components for energy and environmental systems. Performance requirements and processing challenges are identified for the successful implementation different joining technologies. An overview will be provided of several joining approaches which have been developed for high temperature applications. In addition, various characterization approaches were pursued to provide an understanding of the processing-microstructure-property relationships. Microstructural analysis of the joint interfaces was conducted using optical, scanning electron, and transmission electron microscopy to identify phases and evaluate the bond quality. Mechanical testing results will be presented along with the need for new standardized test methods. The critical need for tailoring interlayer compositions for optimum joint properties will also be highlighted.

EMERGENCY RESPONSE FOR PUBLIC WATER SUPPLIES AFTER HURRICANE KATRINA

EPA Science Inventory

Hurricane Katrina resulted in damage and destruction to local water supplies in Mississippi and Louisiana affecting millions of people. Immediately following the devastation, a multidisciplinary team of 30 EPA emergency response, research, and water program personnel joined force...

77 FR 21622 - Special Medical Advisory Group; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... Affiliations Council, ethics, an update on social services, and the White House initiative, ``Joining Forces... Administrative Operations (10B), VHA, 810 Vermont Avenue NW., Washington, DC 20420, or by email at j.t[email protected

Lifeworld-Oriented Family Support

ERIC Educational Resources Information Center

Razpotnik, Špela; Turnšek, Nada; Rapuš-Pavel, Jana; Poljšak-Škraban, Olga

2016-01-01

Since the spring of 2014, the authors of this article, joined by a wider group of students, have been dedicated to researching vulnerable families and their involvement with education systems. In the initial phase, we explored the experiences and challenges that these families face and how they understand and address these challenges. Next, we…

EPA and GSA Webinar: E Scrap Management, Computers for Learning and the Federal Green Challenge

EPA Pesticide Factsheets

EPA and the General Services Administration (GSA) are hosting a webinar on May 2, 2018. Topics will include policies and procedures on E Scrap management, a review of the Computers For Leaning Program, and benefits of joining the Federal Green Challenge.

Why We Need a European Vision

ERIC Educational Resources Information Center

Ravenhall, Mark

2012-01-01

All the countries of the United Kingdom have something to learn from nations facing comparable challenges elsewhere in Europe. Seeing these challenges through a European lens can help these countries understand them and their selves better. The author thinks they need to join in solidarity with adult educators across Europe and, indeed, further…

Flexible twist for pitch control in a high altitude long endurance aircraft with nonlinear response

NASA Astrophysics Data System (ADS)

Bond, Vanessa L.

Information dominance is the key motivator for employing high-altitude long-endurance (HALE) aircraft to provide continuous coverage in the theaters of operation. A joined-wing configuration of such a craft gives the advantage of a platform for higher resolution sensors. Design challenges emerge with structural flexibility that arise from a long-endurance aircraft design. The goal of this research was to demonstrate that scaling the nonlinear response of a full-scale finite element model was possible if the model was aeroelastically and "nonlinearly" scaled. The research within this dissertation showed that using the first three modes and the first bucking modes was not sufficient for proper scaling. In addition to analytical scaling several experiments were accomplished to understand and overcome design challenges of HALE aircraft. One such challenge is combated by eliminating pitch control surfaces and replacing them with an aft-wing twist concept. This design option was physically realized through wind tunnel measurement of forces, moments and pressures on a subscale experimental model. This design and experiment demonstrated that pitch control with aft-wing twist is feasible. Another challenge is predicting the nonlinear response of long-endurance aircraft. This was addressed by experimental validation of modeling nonlinear response on a subscale experimental model. It is important to be able to scale nonlinear behavior in this type of craft due to its highly flexible nature. The validation accomplished during this experiment on a subscale model will reduce technical risk for full-scale development of such pioneering craft. It is also important to experimentally reproduce the air loads following the wing as it deforms. Nonlinearities can be attributed to these follower forces that might otherwise be overlooked. This was found to be a significant influence in HALE aircraft to include the case study of the FEM and experimental models herein.

The Effects of Spanwise Structures and Unsteady Forcing of Vortex Generators on a Shock-Induced Separated Flow Using Planar Laser Scattering

DTIC Science & Technology

2006-05-01

official policy or position of the United States Air Force, Department of Defense, or the U.S. Government." Report Documentation Page Form ApprovedOMB...I join my advisors in gratefully acknowledging the Air Force Office of Scientific Research for their support of this research under grant FA9550...was supplied with approximately 140 ft3 (4 m3) of air by a Worthington HB4 four-stage compressor. The air was stored in external tanks at a pressure

Out of the SHADOW: watch parts in the spotlight -- laser beam microwelding of delicate watch components

NASA Astrophysics Data System (ADS)

Kramer, Thorsten; Olowinsky, Alexander M.

2003-07-01

Conventional joining techniques like press fitting or crimping require the application of mechanical forces to the parts which, in combination with the tolerances of both parts to be joined, lead to imprecision and poor tensile strength. In contrast, laser beam micro welding provides consistent joining and high flexibility and it acts as an alternative as long as press fitting, crimping, screwing or gluing are not capable of batch production. Different parts and even different metals can be joined in a non-contact process at feed rates of up to 60 m/min and with weld seam lengths from 0.6 mm to 15.7 mm. Due to the low energy input, typically 1 J to 6 J, a weld width as small as 50 μm and a weld depth as small as 20 μm have been attained. This results in low distortion of the joined watch components. Since the first applications of laser beam micro welding of watch components showed promising results, the process has further been enhanced using the SHADOW technique. Aspects of the technique such as tensile strength, geometry and precision of the weld seam as well as the acceptance amongst the -mostly conservative- watch manufacturers have been improved.

Adoption & Foster Care

MedlinePlus

... Family Life > Family Dynamics > Adoption & Foster Care Adoption & Foster Care Article Body ​Each year, many children join families through adoption and foster care. These families may face unique challenges. The ...

FOIA Home

Science.gov Websites

Information Access Policy & Compliance BranchInformation Access Policy & Compliance Branch Join the Air Force Home Offices By Command By Base Library Handbook Annual Reports Resources Privacy Act Search Information Access Policy & Compliance Branch

Joining Forces

ERIC Educational Resources Information Center

Parsley, Danette; LaBounty, Sarah

2007-01-01

Marzano (2003) identified 11 factors that positively influence student achievement. Those factors can be divided into three categories: school-level practices, teacher-level practices, and student-level characteristics. Interestingly, Marzano (2000) found that school- and teacher-level influences account for only 20% of the variance in student…

High-Powered, Ultrasonically Assisted Thermal Stir Welding

NASA Technical Reports Server (NTRS)

Ding, Robert

2013-01-01

This method is a solid-state weld process capable of joining metallic alloys without melting. The weld workpieces to be joined by thermal stir welding (TSW) are drawn, by heavy forces, between containment plates past the TSW stir tool that then causes joining of the weld workpiece. TSW is similar to friction stir welding (FSW) in that material is heated into a plastic state (not melted) and stirred using a stir rod. The FSW pin tool is an integrated geometrical structure consisting of a large-diameter shoulder, and a smaller-diameter stir pin protruding from the shoulder. When the pin is plunged into a weld workpiece, the shoulder spins on the surface of the weld workpiece, thus inducing frictional heat into the part. The pin stirs the fraying surfaces of the weld joint, thus joining the weld workpiece into one structure. The shoulder and stir pin of the FSW pin tool must rotate together at a desired rotational speed. The induced frictional energy control and stir pin control of the pin tool cannot be de-coupled. The two work as one integrated unit. TSW, on the other hand, de-couples the heating and stirring of FSW, and allows for independent control of each process element. A uniquely designed induction coil heats the weld workpiece to a desired temperature, and once heated, the part moves into a stir rod whose RPM is also independently controlled. As the weld workpiece moves into the stir rod, the piece is positioned, or sandwiched, between upper and lower containment plates. The plate squeezes together, thus compressing the upper and lower surfaces of the weld workpiece. This compressive force, also called consolidation force, consolidates the plastic material within the weld nugget material as it is being stirred by the stir rod. The stir rod is positioned through the center of the top containment plate and protrudes midway through the opposite lower containment plate where it is mechanically captured. The upper and lower containment plates are separated by a distance equal to the thickness of the material being welded. The TSW process can be significantly improved by reducing the draw forces. This can be achieved by reducing the friction forces between the weld workpieces and the containment plates. High-power ultrasonic (HPU) vibrations of the containment plates achieve friction reduction in the TSW process. Furthermore, integration of the HPU energy into the TSW stir rod can increase tool life of the stir rod, and can reduce shear forces to which the stir rod is subjected during the welding process. TSW has been used to successfully join 0.500-in (˜13-mm) thick commercially pure (CP) titanium, titanium 6AL- 4V, and titanium 6AL-4V ELI in weld joint lengths up to 9 ft (˜2.75-m) long. In addition, the TSW process was used to fabricate a sub-scale hexagonally shaped gun turret component for the U.S. Navy. The turret is comprised of six 0.5000-in (˜13-mm) thick angled welds. Each angled weld joint was prepared by machining the mating surfaces to 120deg. The angled weld joint was then fixtured using an upper and lower containment plate of the same geometry of the angled weld joint. The weld joint was then stirred by the stir rod as it and the upper and lower containment plates traverse through the angled joint prep.

Critical Race Ethnography of Higher Education: Racial Risk and Counter-Storytelling

ERIC Educational Resources Information Center

Ramos, Teresa

2013-01-01

The Ethnography of the University Initiative (EUI) joins a long history of critique, challenge and transformation of higher education. EUI courses are an important site for the creation of non-traditional narratives in which students challenge "business-as-usual" in higher education. For under-represented students, this includes inquiry…

Active and Democratic Citizenship Education and Its Challenges in Social Studies Classrooms

ERIC Educational Resources Information Center

Ersoy, Arife Figen

2014-01-01

Problem Statement: Turkey's passive and task-oriented approach to citizenship education, which has endured since the Ottoman Empire period, has begun to change into more active and democratic citizenship education since Turkey joined the European Union. Identifying the practical problems as well as describing the challenges when practicing the…

Pilot James Barrilleaux with ER-2 aircraft on ramp

NASA Image and Video Library

1998-03-18

James Barrilleaux is the assistant chief pilot for ER-2s in the Flight Crew Branch of NASA's Dryden Flight Research Center, Edwards, California. The ER-2s--civilian variants of the military U-2S reconnaissance aircraft--are part of NASA's Airborne Science program. The ER-2s can carry airborne scientific payloads of up to 2,600 pounds to altitudes of about 70,000 feet to investigate such matters as earth resources, celestial phenomena, atmospheric chemistry and dynamics, and oceanic processes. Barrilleaux has held his current position since February 1998. Barrilleaux joined NASA in 1986 as a U-2/ER-2 pilot with NASA's Airborne Science program at Ames Research Center, Moffett Field, California. He flew both the U-2C (until 1989) and the ER-2 on a wide variety of missions both domestic and international. Barrilleaux flew high-altitude operations over Antarctica in which scientific instruments aboard the ER-2 defined the cause of ozone depletion over the continent, known as the ozone hole. He has also flown the ER-2 over the North Pole. Barrilleaux served for 20 years in the U.S. Air Force before he joined NASA. He completed pilot training at Reese Air Force Base, Lubbock, Texas, in 1966. He flew 120 combat missions as a F-4 fighter pilot over Laos and North Vietnam in 1970 and 1971. He joined the U-2 program in 1974, becoming the commander of an overseas U-2 operation in 1982. In 1983, he became commander of the squadron responsible for training all U-2 pilots and SR-71 crews located at Beale Air Force Base, Marysville, California. He retired from the Air Force as a lieutenant colonel in 1986. On active duty, he flew the U-2, F-4 Phantom, the T-38, T-37, and the T-33. His decorations included two Distinguished Flying Crosses, 12 Air Medals, two Meritorious Service Medals, and other Air Force and South Vietnamese awards. Barrilleaux earned a bachelor of science degree in chemical engineering from Texas A&M University, College Station, in 1964 and a master of science

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farrell, John

DOE's Office of Sustainable Transportation has joined forces with ten national laboratories to launch the New Fuels and Vehicle Systems Optima (NFVSO) research, development, and deployment (RD&D) initiative to co-optimize fuels and vehicles and bring stronger solutions to market faster. This presentation provides a brief overview of the effort.

Leveraging Citizens and Cultivating Vigilance for Force Multiplication in the Maritime Domain

DTIC Science & Technology

2007-09-01

joining CAN, have demonstrated their commitment to maintain a high level of engagement. Researches suggest that individuals volunteer to satisfy...10 G. RESEARCH GOALS AND RESEARCH QUESTIONS ...........................12 II. LITERATURE REVIEW...61 VI. RESEARCH QUESTION ONE................................................................................63 A. DO

Defense.gov Special Report: Joining Forces - Supporting America's Military

Science.gov Websites

being updated and may no longer be applicable as a result of changes in law, regulation and/or content available is no longer being updated and may no longer be applicable as a result of changes in law

Process optimization of joining by upset bulging with local heating

NASA Astrophysics Data System (ADS)

Rusch, Michael; Almohallami, Amer; Sviridov, Alexander; Bonk, Christian; Behrens, Bernd-Arno; Bambach, Markus

2017-10-01

Joining by upset bulging is a mechanical joining method where axial load is applied to a tube to form two revolving bulges, which clamp the parts to be joined and create a force and form fit. It can be used to join tubes with other structures such as sheets, plates, tubes or profiles of the same or different materials. Other processes such as welding are often limited in joining multi-material assemblies or high-strength materials. With joining by upset bulging at room temperature, the main drawback is the possible initiation of damage (cracks) in the inner buckling zone because of high local stresses and strains. In this paper, a method to avoid the formation of cracks is introduced. Before forming the bulge the tube is locally heated by an induction coil. For the construction steel (E235+N) a maximum temperature of 700 °C was used to avoid phase transformation. For the numerical study of the process the mechanical properties of the tube material were examined at different temperatures and strain rates to determine its flow curves. A parametrical FE model was developed to simulate the bulging process with local heating. Experiments with local heating were executed and metallographic studies of the bulging area were conducted. While specimens heated to 500 °C showed small cracks left, damage-free flanges could be created at 600 and 700 °C. Static testing of damage-free bulges showed improvements in tensile strength and torsion strength compared to bulges formed at room-temperature, while bending and compression behavior remained nearly unchanged. In cyclic testing the locally heated specimens underwent about 3.7 times as many cycles before failure as the specimens formed at room temperature.

Inside KSC! for Aug. 25, 2017

NASA Image and Video Library

2017-08-25

A United Launch Alliance Atlas V lifted off from Cape Canaveral Air Force Station's Space Launch Complex 41, boosting NASA's Tracking and Data Relay Satellite-M to orbit. Kennedy Space Center employees also joined Americans from coast to coast on Monday to witness the solar eclipse.

Research Notes : ODOT and USGS join forces to ask, how low can you flow?

DOT National Transportation Integrated Search

2008-06-01

Likewise in Oregon, hundreds of river reaches are home to endangered or threatened aquatic species. Water handling structures, such as culverts, need to be designed to accommodate aquatic life over most of the range of flows they experience. : Tempor...

4 Schools for WIE. Evaluation Report

ERIC Educational Resources Information Center

Erkut, Sumru; Marx, Fern

2005-01-01

With funding from the National Science Foundation, engineering schools at Northeastern University, Tufts University, Worcester Polytechnic Institute, and Boston University joined forces in an effort to increase the number of girls who develop an interest in science, technology, engineering, and mathematics (STEM) fields during the middle school…

Integrated system links cost data, patient satisfaction scores for the first time.

PubMed

1999-10-01

Linking cost data, patient satisfaction scores. HBS International and The Picker Institute have joined forces to make integrated data available that directly links operational efficiency and patient satisfaction. Find out how the systems lets providers know when reducing expenses compromises care.

Joining Forces

ERIC Educational Resources Information Center

Kennedy, Mike

2006-01-01

As education institutions more readily pursue stronger connections with the entire community, joint-use programs allow them to forge those bonds more effectively--providing entire communities with more access to facilities and services, often critically needed in some areas, and more efficient use of tax funds. Through joint-use agreements,…

Joining of Components of Complex Structures for Improved Dynamic Response

DTIC Science & Technology

2011-10-28

system- level mass and stiffness matrices and force vector (at each frequency in the range of interest). To address this issue a series of complex...displacements of all candidate joint locations by using the system- level mass and stiffness matrices and force vector (at each frequency in the range of...joints. In contrast, Li et al. [10] proposed a fastener layout/topology that achieves an almost uniform stress level in each joint, and adopted

Optical contacting of quartz

NASA Technical Reports Server (NTRS)

Payne, L. L.

1982-01-01

The strength of the bond between optically contacted quartz surfaces was investigated. The Gravity Probe-B (GP-B) experiment to test the theories of general relativity requires extremely precise measurements. The quartz components of the instruments to make these measurements must be held together in a very stable unit. Optical contacting is suggested as a possible method of joining these components. The fundamental forces involved in optical contacting are reviewed and relates calculations of these forces to the results obtained in experiments.

Method for joining metal by solid-state bonding

DOEpatents

Burkhart, L. Elkin; Fultz, Chester R.; Maulden, Kerry A.

1979-01-01

The present development is directed to a method for joining metal at relatively low temperatures by solid-state bonding. Planar surfaces of the metal workpieces are placed in a parallel abutting relationship with one another. A load is applied to at least one of the workpieces for forcing the workpieces together while one of the workpieces is relatively slowly oscillated in a rotary motion over a distance of about 1.degree.. After a preselected number of oscillations, the rotary motion is terminated and the bond between the abutting surfaces is effected. An additional load may be applied to facilitate the bond after terminating the rotary motion.

Study on seismic performance of BFRP geogrid reinforced Tibetan rubble wall

NASA Astrophysics Data System (ADS)

Yang, Dan; Jia, Bin; Huang, Hui; Deng, Chuangli

2018-03-01

For the study of BFRP geogrid influence on Tibetan rubble wall seismic performance, in this paper, on the premise of not change the way of traditional masonry, laying and not join geogrid respectively on the the rubble wall, and carries on the cyclic loading experiment on them. The damage characteristics, crack width and seismic performance of the rubble walls with BFRP geogrid are studied. The experimental results show that the deformation of the rubble wall is mainly the shear deformation under the action of horizontal force, and the bearing capacity and energy dissipation capacity of the wall can be improved significantly after joining the geogrid.

International Students Take Up the Model Solar Car Challenge.

ERIC Educational Resources Information Center

Wellington, Paul

2000-01-01

Introduces an event in which two school teams from Argentina and Vietnam joined those from each Australian state in a race of model cars powered by the sun that provides a challenging and exciting approach for students to apply their scientific and technological knowledge to design and build the most efficient vehicles possible to gain hands-on…

Experimental Investigation on the Joining of Aluminum Alloy Sheets Using Improved Clinching Process.

PubMed

Chen, Chao; Zhao, Shengdun; Han, Xiaolan; Zhao, Xuzhe; Ishida, Tohru

2017-08-01

Aluminum alloy sheets have been widely used to build the thin-walled structures by mechanical clinching technology in recent years. However, there is an exterior protrusion located on the lower sheet and a pit on the upper sheet, which may restrict the application of the clinching technology in visible areas. In the present study, an improved clinched joint used to join aluminum alloy sheets was investigated by experimental method. The improved clinching process used for joining aluminum alloy evolves through four phases: (a) localized deformation; (b) drawing; (c) backward extrusion; and (d) mechanical interlock forming. A flat surface can be produced using the improved clinching process. Shearing strength, tensile strength, material flow, main geometrical parameters, and failure mode of the improved clinched joint were investigated. The sheet material was compressed to flow radially and upward using a punch, which generated a mechanical interlock by producing severe localized plastic deformation. The neck thickness and interlock of the improved clinched joint were increased by increasing the forming force, which also contributed to increase the strength of the clinched joint. The improved clinched joint can get high shearing strength and tensile strength. Three main failure modes were observed in the failure process, which were neck fracture mode, button separation mode, and mixed failure mode. The improved clinched joint has better joining quality to join aluminum alloy sheets on the thin-walled structures.

Experimental Investigation on the Joining of Aluminum Alloy Sheets Using Improved Clinching Process

PubMed Central

Chen, Chao; Zhao, Shengdun; Han, Xiaolan; Zhao, Xuzhe; Ishida, Tohru

2017-01-01

Aluminum alloy sheets have been widely used to build the thin-walled structures by mechanical clinching technology in recent years. However, there is an exterior protrusion located on the lower sheet and a pit on the upper sheet, which may restrict the application of the clinching technology in visible areas. In the present study, an improved clinched joint used to join aluminum alloy sheets was investigated by experimental method. The improved clinching process used for joining aluminum alloy evolves through four phases: (a) localized deformation; (b) drawing; (c) backward extrusion; and (d) mechanical interlock forming. A flat surface can be produced using the improved clinching process. Shearing strength, tensile strength, material flow, main geometrical parameters, and failure mode of the improved clinched joint were investigated. The sheet material was compressed to flow radially and upward using a punch, which generated a mechanical interlock by producing severe localized plastic deformation. The neck thickness and interlock of the improved clinched joint were increased by increasing the forming force, which also contributed to increase the strength of the clinched joint. The improved clinched joint can get high shearing strength and tensile strength. Three main failure modes were observed in the failure process, which were neck fracture mode, button separation mode, and mixed failure mode. The improved clinched joint has better joining quality to join aluminum alloy sheets on the thin-walled structures. PMID:28763027

The Oklahoma Attorney General's Task Force report on the State of End-of-Life Health Care, 2005.

PubMed

Edmondson, W A Drew

2005-05-01

This article includes the recommendations submitted by the 15 members of the Oklahoma Attorney General's Task Force in their Report on the State of End-of-Life Health Care. The task force was created on April 21, 2004, and their report was accepted by Attorney General W.A. Drew Edmondson at a press conference April 11, 2005. It has been forwarded to members of the Oklahoma Legislature, relevant state agencies and organizations with an invitation to join with members of the task force to continue efforts to improve end-of-life care for Oklahomans. Copies of the report are available upon request to the Office of Attorney General.

Challenges and Opportunities in Design, Fabrication, and Testing of High Temperature Joints in Ceramics and Ceramic Composites

NASA Technical Reports Server (NTRS)

Singh, M.; Levine, S. R. (Technical Monitor)

2001-01-01

Ceramic joining has been recognized as an enabling technology for successful utilization of advanced ceramics and composite materials. A number of joint design and testing issues have been discussed for ceramic joints in silicon carbide-based ceramics and fiber-reinforced composites. These joints have been fabricated using an affordable, robust ceramic joining technology (ARCJoinT). The microstructure and good high temperature mechanical capability (compressive and flexural strengths) of ceramic joints in silicon carbide-based ceramics and composite materials are reported.

A report on the 2012 outfield variety tests

USDA-ARS?s Scientific Manuscript database

A dependable and sustainable source of new sugarcane varieties is the life-blood of the Louisiana Sugarcane Industry. To that end, the American Sugarcane League, the Louisiana State University AgCenter, and the USDA Agricultural Research Service have joined forces to insure that life-blood continues...

Developing a Cooperative Online Degree Programs--The Practical Mechanics.

ERIC Educational Resources Information Center

Runyon, Darla; Von Holzen, Roger

Three Missouri state institutions (Lincoln University, Northwest Missouri State University, and Southeast Missouri State University) have joined forces to develop a cooperative online Masters in Education in Teaching and Learning: Elementary degree. This presentation focuses on the mechanics behind the development and delivery of this unique…

Software Manuals: Where Instructional Design and Technical Writing Join Forces.

ERIC Educational Resources Information Center

Thurston, Walter, Ed.

1986-01-01

Presents highlights from a panel discussion by well known San Francisco Bay area documentation writers, instructional designers, and human performance technologists. Three issues on user performance and documentation are addressed: whether people avoid reading user manuals and why; major human factors influencing documentation use; and…

It's on the Line: Tech Policies that Make Sense

ERIC Educational Resources Information Center

Calhoun, Kelly J.

2012-01-01

ACSA (Association of California School Administrators), the CSBA (California School Boards Association), the California Educational Technology Professionals Association, the Santa Clara County Office of Education, CUE (Computer Using Educators), the law firm Fagen, Friedman & Fulfrost and others have joined forces to develop policies that can…

Stacey Rothgeb | NREL

Science.gov Websites

Stacey Rothgeb Photo of Stacey Rothgeb Stacey Rothgeb Manager, Residential Integration & . Prior to joining NREL, Stacey worked as the energy manager at the U.S. Air Force Academy. She also owned (PE) and a Certified Energy Manager (CEM). Education B.S. Architectural Engineering, Kansas State

Schools Enlisting Defense Industry to Boost STEM

ERIC Educational Resources Information Center

Trotter, Andrew

2008-01-01

Defense contractors Northrop Grumman Corp. and Lockheed Martin Corp. are joining forces in an innovative partnership to develop high-tech simulations to boost STEM--or science, technology, engineering, and mathematics--education in the Baltimore County schools. The Baltimore County partnership includes the local operations of two major military…

Sustainable Materials Management

EPA Pesticide Factsheets

To introduce businesses, NGOs, and government officials to the concept of Sustainable Materials Management (SMM). To provide tools to allow stakeholders to take a lifecycle approach managing their materials, & to encourage them to join a SMM challenge.

Postpartum Policies For Military Mothers: Their Impact On Retention Of Female Air Force Officers

DTIC Science & Technology

2017-10-01

time and energy devoted to the family, men are certainly not free from this pressure. Segal notes that the family goes through different life phases in...despite a spouse’s income or time spent working.lxv Another study showed that even when women made more money and worked more hours than their...they love what they do with a passion for the Air Force mission. While many of the women joined the service for convenience, free education or stable

Disruptive Technology for Vector Control: the Innovative Vector Control Consortium and the US Military Join Forces to Explore Transformative Insecticide Application Technology for Mosquito Control Programmes

DTIC Science & Technology

2015-09-26

Forces Pest Management Board (AFPMB) focused on public health pesticide application technology. Three main top- ics were discussed: the limitations...industry, the World Health Organization, the Bill and Melinda Gates Foundation and others. Keywords: Pesticide application, Indoor residual spraying (IRS...Navy Entomology Center of Excel- lence (NECE), and industry as part of a joint workshop focused on public health pesticide application technology

Conjoined Cochlear Models:. the Twamp and the Sandwich

NASA Astrophysics Data System (ADS)

Hubbard, Allyn

2009-02-01

A new model of the cochlea is created by joining parts of the traveling-wave amplifier (TWAMP) and the Sandwich models. The lossy, untuned traveling-wave line of the TWAMP is retained, but the TWAMP's tuned traveling-wave line is replaced by the Sandwich's traveling-wave line that represents the reticular lamina (RL) and scala tympani. The model combines stereocilliary forces, which act between the tectorial membrane (TM) and RL, with somatic outer hair cell forces that power the Sandwich.

Team Teaching with Academic Core Curricula Teachers: Using Aviation Concepts

ERIC Educational Resources Information Center

Berentsen, Lowell W.

2006-01-01

Technology education teachers today have at their disposal the skills, opportunity, experience, ingenuity, expertise, equipment, and environment to greatly improve students' ability to learn and apply the knowledge they have gained in their academic programs. When a technology education teacher joins forces with an academic core teacher, the…

Reviving a Community, Modernizing an Industry: Ireland's Furniture College.

ERIC Educational Resources Information Center

Regional Technology Strategies, Inc., Carrboro, NC.

Connemara, a rural region in Ireland, is characterized by high unemployment, high emigration, poor infrastructure, inadequate public services, and a low rate of transfer to third-level education. To address the situation, the Galway-Mayo Institute of Technology (GMIT), joined forces with Connemara West (a community-owned development organization…

Defense.gov Special Report: Travels With Work

Science.gov Websites

Work Meets With Japanese Leaders Deputy Defense Secretary Bob Work met with Japanese leaders to discuss discuss bilateral efforts to enhance alliance force posture and capabilities. Story Twitter Feed News /Section 508 Join the Military Careers Web Policy Stay Connected Icon: Facebook Facebook Icon: Twitter

The Intentions of Men 23 to 29 Years Old to Join the Military: Results of a National Survey

DTIC Science & Technology

1982-09-01

younger counterparts. This finding suggests that marketing and advertising strategies should be undertaken by the services individually. An all-service...NAVPERSRANDCEN, repre- sentatives of the Joint Marketing and Advertising Research Committee (which includes participants from the Air Force, Army, Marine

Clean Cities Roadmap : A resource for developing, implementing, and sustaining your clean cities program

DOT National Transportation Integrated Search

2001-08-01

This roadmap explains how your community can join forces with the nationwide network of Clean Cities to increase the use of alternative fuels and alternative fuel vehicles (AFVs). You will learn how the U.S. Department of Energy (DOE) can help your c...

Defense.gov - Special Report: Biosurveillance - 2012

Science.gov Websites

Health Security Effort to Boost Global Disease Response Top administration officials are joining Biosurveillance A new biosurveillance division at the Armed Forces Health Surveillance Center is working to fill gaps at the convergence of battlefield biodefense and health surveillance. Story U.S., EU Lead Global

Settling the 'Score' with Heart Disease

NASA Technical Reports Server (NTRS)

2004-01-01

Technology and medicine forged a bond in 1986 when a group of dedicated NASA scientists, University of Southern California (USC) medical professors, and a Dutch cardiologist joined forces to prevent heart attacks, using ultrasound images of astronauts blood-flow patterns and the supercomputer depended upon to orchestrate the "Star Wars" Strategic Defense Initiative.

Joining Forces

ERIC Educational Resources Information Center

Sawchuk, Stephen; Sparks, Sarah D.; Cavanagh, Sean; Samuels, Christina A.

2011-01-01

A mantra in recent years has been to blame the teachers' unions for many of the problems that beset public education. Americans only need look at Wisconsin, where the governor and lawmakers pushed through legislation curtailing the collective bargaining rights of teachers and other public employees. This special report examines the attempts by a…

Reassessing the Individual Ready Reserve’s Role in the Marine Corps Total Force

DTIC Science & Technology

2008-01-01

a Major Subordinate Command ofMFR. MOBCOM maintains operatio ~al and administrative control of the IRR. In 2005, Brigadier General Darrell Moore...separating veterans join the IRR, complete with the conditions ofa very stressful period of enlistment. The research shows that because of the inventory

Tough Times Push More Small Colleges to Join Forces

ERIC Educational Resources Information Center

Carlson, Scott

2013-01-01

The author reports on how colleges could work together more closely in areas like the library, the colleges' technology infrastructure, human resources and payroll, and, ultimately, their academic programs. Higher education has some famous collaborations--the best-known among them are the Claremont Colleges, where seven institutions, each with a…

Is the Endowment Model Still Working?

ERIC Educational Resources Information Center

Jarvis, William

2010-01-01

When Commonfund and the National Association of College and University Business Officers (NACUBO) announced in late 2008 that they would join forces to combine their two endowment studies, which had historically been fielded and reported separately, they had high hopes for the venture, but those hopes were tempered with caution. The financial…

Maine Leading Initiative for Multistate Tech. Buys

ERIC Educational Resources Information Center

Cavanagh, Sean

2013-01-01

A group of states has joined forces to arrange the purchase of an unusually comprehensive set of educational-technology devices and services, in a compact that could foreshadow other cooperative efforts by state and local governments attempting to turn the digital-procurement process to their advantage. The initial partners in the multistate…

The Achievement Club

ERIC Educational Resources Information Center

Rogers, Ibram

2009-01-01

When Gabrielle Carpenter became a guidance counselor in Northern Virginia nine years ago, she focused on the academic achievement gap and furiously tried to close it. At first, she was compelled by tremendous professional interest. However, after seeing her son lose his zeal for school, Carpenter joined forces with other parents to form an…

The Promise of Partnerships: Researchers Join Forces with Educators to Solve Problems of Practice of Partnerships

ERIC Educational Resources Information Center

Meister, Gail R.; Blitz, Cynthia L.

2016-01-01

An auxiliary and potentially powerful source of practitioners' knowledge, skills, and dispositions can come from participation in research-practice partnerships. Research-practice partnerships link researchers, usually faculty at institutions of higher education, with practitioners working in schools, district central offices, county offices, or…

78 FR 28461 - Military Spouse Appreciation Day, 2013

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-14

... caretakers for our wounded warriors. America's military spouses are at the core of our Armed Forces, and on... mortgage assistance for military homeowners. Through First Lady Michelle Obama and Dr. Jill Biden's Joining... Vol. 78 Tuesday, No. 93 May 14, 2013 Part V The President Proclamation 8976--Military Spouse...

77 FR 28759 - Military Spouse Appreciation Day, 2012

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-16

... back to our country day after day. The strength and readiness of America's military depends on the well... heroes, our Nation's military spouses also offer tremendous service and make great sacrifices for our....JoiningForces.gov . America's service members represent only one percent of our population, but they...

Close Encounters with the Turbulent Environment of Urban Education.

ERIC Educational Resources Information Center

Jefferson, Arthur; Levey, Richard

1978-01-01

In order to improve the quality of urban education, public school educators must be joined by the public, legislators, business leaders, and social planners. These individuals will need to understand public policy priorities, as well as the social, economic, and political forces which define our present environment. (Author/GC)

Joining dissimilar materials using Friction Stir scribe technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep

2016-10-03

The ability to effectively join materials with vastly different melting points like Aluminum-Steel, Polymer composites - metals has been one of the road blocks in realizing multi-material components for light weighting efforts. Friction stir scribe (FSS) technique is a promising method that produces continuous overlap joint between materials with vastly different melting regimes and high temperature flow characteristics. FSS uses an offset cutting tool at the tip of the FSW pin to create an insitu mechanical interlock between material interfaces. With investments from Vehicle Technology office, US DOE and several automotive manufacturers and suppliers PNNL is developing the FSS processmore » and has demonstrated viability of joining several material combinations. Details of welding trails, unique challenges and mitigation strategies in different material combinations will be discussed. Joint characterization including mechanical tests and joint performances will also be presented.« less

Innovation in health policy: responding to the health society.

PubMed

Kickbusch, Ilona

2007-01-01

The 21st century health society is characterized by 2 major social processes: the expansion of the territory of health and the expansion of the reflexivity of health. The boundaries of what we call the are becoming increasingly fluid and health has become integral to how we live our everyday life. Health itself has become a major economic and social driving force in society. This shifts the pressure for policy innovation from a focus on the existing health system to a reorganization of how we approach health in 21st century societies. The dynamics of the health society challenge the way we conceptualize and locate health in the policy arena, the mechanisms through which we conduct health policy and they redefine who should be involved in the policy process. This concern is beginning to be addressed within government through joined up government approaches, beyond government through making health everybody's business and beyond nation states as a new interface between domestic and foreign policy.

Investigation of Thermoelectric Parameters of Bi2Te3: TEGs Assembled using Pressure-Assisted Silver Powder Sintering-Based Joining Technology

NASA Astrophysics Data System (ADS)

Stranz, Andrej; Waag, Andreas; Peiner, Erwin

2015-06-01

Operation of thermoelectric generator (TEG) modules based on bismuth telluride alloys at temperatures higher than 250°C is mostly limited by the melting point of the assembly solder. Although the thermoelectric parameters of bismuth telluride materials degrade for temperatures >130°C, the power output of the module can be enhanced with an increase in the temperature difference. For this, a temperature-stable joining technique, especially for the hot side of the modules, is required. Fabrication and process parameters of TEG modules consisting of bismuth telluride legs, alumina ceramics and copper interconnects using a joining technique based on pressure-assisted silver powder sintering are described. Measurements of the thermal force, electrical resistance, and output power are presented that were performed for hot side module temperatures up to 350°C and temperature differences higher than 300°C. Temperature cycling and results measured during extended high-temperature operation are addressed.

Alternative end-joining pathway(s): bricolage at DNA breaks.

PubMed

Frit, Philippe; Barboule, Nadia; Yuan, Ying; Gomez, Dennis; Calsou, Patrick

2014-05-01

To cope with DNA double strand break (DSB) genotoxicity, cells have evolved two main repair pathways: homologous recombination which uses homologous DNA sequences as repair templates, and non-homologous Ku-dependent end-joining involving direct sealing of DSB ends by DNA ligase IV (Lig4). During the last two decades a third player most commonly named alternative end-joining (A-EJ) has emerged, which is defined as any Ku- or Lig4-independent end-joining process. A-EJ increasingly appears as a highly error-prone bricolage on DSBs and despite expanding exploration, it still escapes full characterization. In the present review, we discuss the mechanism and regulation of A-EJ as well as its biological relevance under physiological and pathological situations, with a particular emphasis on chromosomal instability and cancer. Whether or not it is a genuine DSB repair pathway, A-EJ is emerging as an important cellular process and understanding A-EJ will certainly be a major challenge for the coming years. Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

Microassembly of Heterogeneous Materials using Transfer Printing and Thermal Processing

PubMed Central

Keum, Hohyun; Yang, Zining; Han, Kewen; Handler, Drew E.; Nguyen, Thong Nhu; Schutt-Aine, Jose; Bahl, Gaurav; Kim, Seok

2016-01-01

Enabling unique architectures and functionalities of microsystems for numerous applications in electronics, photonics and other areas often requires microassembly of separately prepared heterogeneous materials instead of monolithic microfabrication. However, microassembly of dissimilar materials while ensuring high structural integrity has been challenging in the context of deterministic transferring and joining of materials at the microscale where surface adhesion is far more dominant than body weight. Here we present an approach to assembling microsystems with microscale building blocks of four disparate classes of device-grade materials including semiconductors, metals, dielectrics, and polymers. This approach uniquely utilizes reversible adhesion-based transfer printing for material transferring and thermal processing for material joining at the microscale. The interfacial joining characteristics between materials assembled by this approach are systematically investigated upon different joining mechanisms using blister tests. The device level capabilities of this approach are further demonstrated through assembling and testing of a microtoroid resonator and a radio frequency (RF) microelectromechanical systems (MEMS) switch that involve optical and electrical functionalities with mechanical motion. This work opens up a unique route towards 3D heterogeneous material integration to fabricate microsystems. PMID:27427243

Numerical investigations on the lateral angular co-extrusion of aluminium and steel

NASA Astrophysics Data System (ADS)

Behrens, B.-A.; Klose, C.; Chugreev, A.; Thürer, S. E.; Uhe, J.

2018-05-01

In order to save weight and costs, different materials can be combined within one component. In the novel process chain being developed within the Collaborative Research Centre (CRC) 1153, joined semi-finished workpieces are used to produce hybrid solid components with locally adapted properties. Different materials are joined in an initial step before the forming process takes place. Hereby, the quality of the joining zone is improved by means of the thermo-mechanical treatment during the forming and machining processes. The lateral angular co-extrusion (LACE) approach is used to produce semi-finished workpieces because it allows for the production of coaxial semi-finished products consisting of aluminium and steel. In the further process chain, these semi-finished products are processed into hybrid bearing bushings with locally adapted properties by die forging. In the scope of this work, numerical investigations of the co-extrusion of aluminium-steel compounds were carried out using finite element (FE) simulation in order to examine the influence of the process parameters on the co-extrusion process. For this purpose, the relevant material properties of the aluminium alloy EN AW-6082 were determined experimentally and subsequently implemented in the numerical model. The obtained numerical model was used to study the impact of different ram speeds, press ratios and billet temperatures on the resulting extrusion forces and the material flow. The numerical results have been validated using force-time curves obtained from experimental extrusion tests carried out on a 2.5 MN laboratory extrusion press.

Pilot James Barrilleaux with ER-2 aircraft on ramp

NASA Technical Reports Server (NTRS)

1998-01-01

James Barrilleaux is the assistant chief pilot for ER-2s in the Flight Crew Branch of NASA's Dryden Flight Research Center, Edwards, California. The ER-2s--civilian variants of the military U-2S reconnaissance aircraft--are part of NASA's Airborne Science program. The ER-2s can carry airborne scientific payloads of up to 2,600 pounds to altitudes of about 70,000 feet to investigate such matters as earth resources, celestial phenomena, atmospheric chemistry and dynamics, and oceanic processes. Barrilleaux has held his current position since February 1998. Barrilleaux joined NASA in 1986 as a U-2/ER-2 pilot with NASA's Airborne Science program at Ames Research Center, Moffett Field, California. He flew both the U-2C (until 1989) and the ER-2 on a wide variety of missions both domestic and international. Barrilleaux flew high-altitude operations over Antarctica in which scientific instruments aboard the ER-2 defined the cause of ozone depletion over the continent, known as the ozone hole. He has also flown the ER-2 over the North Pole. Barrilleaux served for 20 years in the U.S. Air Force before he joined NASA. He completed pilot training at Reese Air Force Base, Lubbock, Texas, in 1966. He flew 120 combat missions as a F-4 fighter pilot over Laos and North Vietnam in 1970 and 1971. He joined the U-2 program in 1974, becoming the commander of an overseas U-2 operation in 1982. In 1983, he became commander of the squadron responsible for training all U-2 pilots and SR-71 crews located at Beale Air Force Base, Marysville, California. He retired from the Air Force as a lieutenant colonel in 1986. On active duty, he flew the U-2, F-4 Phantom, the T-38, T-37, and the T-33. His decorations included two Distinguished Flying Crosses, 12 Air Medals, two Meritorious Service Medals, and other Air Force and South Vietnamese awards. Barrilleaux earned a bachelor of science degree in chemical engineering from Texas A&M University, College Station, in 1964 and a master of science degree in systems management from the University of Southern California in 1979. He has accumulated more than 5,800 hours of flying time over a period of 33 years and is currently the oldest active U-2/ER-2 pilot.

Physician volunteers.

PubMed

Milles, G A

1999-01-01

There is an increasing population of working poor in our community. They earn too little to afford health insurance, yet they don't qualify for government assistance. Physician volunteers Howard County have joined together and developed a free clinic to meet this challenge.

An Assessment of Radiation Modification from a European Perspective

NASA Astrophysics Data System (ADS)

Kristjansson, J. E.; Lawrence, M. G.; Boucher, O.; Haywood, J. M.; Irvine, P. J.; Muri, H.; Schmidt, H.; Schulz, M.; Vaughan, N.; Watson, M.; Born, W.; Schaefer, S.; Stelzer, H.

2014-12-01

The European Transdisciplinary Assessment of Climate Engineering (EuTRACE) project (2012-2014) is funded by the European Commission (EC). In EuTRACE, researchers from the natural sciences, social sciences and the humanities have joined forces to assess various proposed geoengineering techniques concerning their radiative forcing potential and side effects, ethical aspects, economics aspects, as well as governance and regulation aspects. A comprehensive assessment report will be submitted to the EC in autumn 2014. We will present some highlights of the part of the EuTRACE assessment that deals with the natural science aspects of proposed Radiation Modification (RM) techniques. The techniques considered are: a) Stratospheric Sulfur Injections; b) Marine Cloud Brightening; c) Desert Brightening; d) Vegetation Brightening; and e) Cirrus Cloud Thinning. A large number of publications in the scientific literature has been considered, as well as recently published assessment reports by the Royal Society in the UK and the German Federal Ministry of Education and Research. Some of the findings of the assessment are: Globally averaged, the current anthropogenic radiative forcing could conceivably be offset by the RM techniques considered. The RM techniques could have a significant global effect already after 1 year or less. Model simulations consistently show that Solar RM leads to regional imbalances due to different spatial footprints of solar and carbon dioxide radiative forcings. This may have significant consequences for precipitation patterns and the hydrological cycle. Very rapid warming is virtually certain if RM were to be stopped abruptly or over a period of one to a few years. Model studies of RM usually assume that the techniques are technologically feasible. In fact, the technological challenges are poorly known, and in many cases the physical processes involved are poorly understood. We will end by discussing key research questions and knowledge gaps.

Finite element method (FEM) analysis of the force systems produced by asymmetric inner headgear bows.

PubMed

Geramy, Allahyar; Kizilova, Natalya; Terekhov, Leonid

2011-11-01

Extra-oral traction appliances were introduced more than a century ago and continue to be used to produce orthopaedic and/or dental changes in the maxilla. While force systems produced by asymmetric outer bows have been studied extensively, the force systems produced by asymmetric inner bows have been overlooked. To analyse the forces acting on the maxillary first molars: when the size of one bayonet bend is increased; when the point of application of the distalising force on the inner bow is moved to one side; when one molar is displaced palatally. Four FEM models of cervical headgear attached to maxillary first molars were designed in SolidWorks 2010 and transferred to an ANSYS Workbench Ver. 12.1. Model 1, each molar was 23 mm from the midpalatal line and the inner bow was symmetrical; Model 2, the left molar was displaced 4 mm towards the midpalatal line and the inner bow was symmetrical; Model 3, the molars were equidistant (23 mm) from the midpalatal line, but the left molar was engaged by a 2 mm larger bayonet bend; Model 4, the molars were equidistant (23 mm) from the midpalatal line but the join between the inner and outer bows was displaced 2 mm towards the left molar. In all FEM models, a 2N force was applied to the inner bow at the join between inner and outer bows and the energy transmitted to the teeth and the von Mises stresses on the molar PDLs were assessed. There were marked differences in the strain energy on the teeth and the von Mises stresses on their PDLs. A 14 to 20 per cent increase in energy and force was produced on the tooth closer to the symmetric plane of the headgear. In addition, the increase in energy produced a 30 to 62 per cent increase in the von Mises stresses within the PDLs. Small asymmetries in molar position, the size of a bayonet bend and the point of application of a force on an inner bow resulted in asymmetrical forces on the molars. These forces were higher on the molar closer to the symmetric plane of the headgear.

Update on Renal Replacement Therapy: Implantable Artificial Devices and Bioengineered Organs.

PubMed

Attanasio, Chiara; Latancia, Marcela T; Otterbein, Leo E; Netti, Paolo A

2016-08-01

Recent advances in the fields of artificial organs and regenerative medicine are now joining forces in the areas of organ transplantation and bioengineering to solve continued challenges for patients with end-stage renal disease. The waiting lists for those needing a transplant continue to exceed demand. Dialysis, while effective, brings different challenges, including quality of life and susceptibility to infection. Unfortunately, the majority of research outputs are far from delivering satisfactory solutions. Current efforts are focused on providing a self-standing device able to recapitulate kidney function. In this review, we focus on two remarkable innovations that may offer significant clinical impact in the field of renal replacement therapy: the implantable artificial renal assist device (RAD) and the transplantable bioengineered kidney. The artificial RAD strategy utilizes micromachining techniques to fabricate a biohybrid system able to mimic renal morphology and function. The current trend in kidney bioengineering exploits the structure of the native organ to produce a kidney that is ready to be transplanted. Although these two systems stem from different technological approaches, they are both designed to be implantable, long lasting, and free standing to allow patients with kidney failure to be autonomous. However, for both of them, there are relevant issues that must be addressed before translation into clinical use and these are discussed in this review.

Art, science and social science in nursing: occupational origins and disciplinary identity.

PubMed

Rafferty, A M

1995-09-01

This paper forms part of a wider study examining the history and sociology of nursing education in England between 1860 and 1948. It argues that the question of whether nursing was an art, science and/or social science has been at the 'heart' of a wider debate on the occupational status and disciplinary identity of nursing. The view that nursing was essentially an art and a 'calling', was championed by Florence Nightingale. Ethel Bedford Fenwick and her allies insisted that nursing, like other professions, was a 'scientific' and technical enterprise. Social scientists later came to challenge nursing's claim to professionalism by analysing nursing work first within the context of industrial psychology. But they also advocated a rapprochement between nursing, health services and social science research, a challenge which we are in nursing, still striving to meet. This paper argues for a strong coalition of nursing with its former nineteenth century ally, social science, in the continuing struggle for change within nursing and health care policy. Rather than searching for some rarified and purified essence of nursing knowledge, it argues that nurses need to join forces with sociologists and economists in striving to shape the agenda for health services research and provide the evidential basis for health policy transformation more generally.

2018 NASA Day of Remembrance

NASA Image and Video Library

2018-01-25

Inside the Center for Space Education at the Kennedy Space Center Visitor Complex, spaceport employees and guests join others throughout NASA for the Day of Remembrance ceremony, honoring the contributions of astronauts who have perished in the conquest of space. Following the ceremony, guests walk to the Space Mirror Memorial. The names of fallen astronauts from Apollo 1, Challenger and Columbia, as well as the astronauts who perished in training and commercial airplane accidents are emblazoned on the monument. Each year spaceport employees and guests join others throughout NASA honoring the contributions of astronauts who have perished in the conquest of space.

A Small War: The Development of the Russian-Chechen Conflict, 1994-2010

DTIC Science & Technology

2011-04-01

joined America and other nations as a member of the Financial Action Task Force ( FATF ./36 By 2004, a Central Asian FATF regional body formed to focus...assisting or working with FATF labeled terrorist groups. Althotlgh Chechnya remains a high criine area, 139 the combination of high profile worldwide

A Mathematics and Science Trail

ERIC Educational Resources Information Center

Smith, Kathy Horak; Fuentes, Sarah Quebec

2012-01-01

In an attempt to engage primary-school students in a hands-on, real-world problem-solving context, a large urban district, a mathematics and science institute housed in a college of education, and a corporate sponsor in the southwest United States, joined forces to create a mathematics and science trail for fourth- and fifth-grade students. A…

Language Centres as Translation-Service Providers: Joining Forces at European Level

ERIC Educational Resources Information Center

Harvey, Julia; Owen, David; Palumbo, Giuseppe

2017-01-01

The Translation Focus Group (TFG) within CercleS has paid particular attention to issues concerning the production of multilingual institutional texts within the context of European higher education, specifically in order to enhance the quality and effectiveness of terminology and style in ways that ensure the availability of the best possible…

Co-Operative Schools: A Democratic Alternative

ERIC Educational Resources Information Center

Audsley, Jamie; Cook, Philip

2012-01-01

Many fear that the pressures of running an Academy will be too great for individual schools, and that they will be forced to join chains run by private companies. These may offer hard-pressed school administrators valuable management expertise and back-office support, but seem to offer wider society little accountability and transparency. Are…

One Community Working Together

ERIC Educational Resources Information Center

Weis, Charles

2011-01-01

In the city of San Jose, more than half of all public school students tested are not proficient in their grade-level skills. This article discusses how school, civic and community leaders have joined forces with the goal of eliminating the achievement gap in San Jose by 2020. This wide and highly inclusive collaboration is made possible by an…

Women and Work-Place Stress. ERIC Digest.

ERIC Educational Resources Information Center

Long, Bonita C.

With North American women joining the work force in record numbers, the effect of employment on women's well-being is gaining attention. This digest examines various stressors affecting women in the work world and some actions companies can take to alleviate these stressors. While some studies show that work has detrimental effects on some…

Does It Make a Difference If You Change the Structure? School-within-a-School.

ERIC Educational Resources Information Center

Nickle, Melinda Nixon; And Others

1990-01-01

Four secondary teachers, long accustomed to working in isolation, joined forces to provide an interdisciplinary program with flexible scheduling and common planning periods. This article describes their school-within-a-school program, its acceptance by the Coalition of Essential Schools, and the program's benefits. A sidebar provides restructuring…

Partnership for a Nation of Learners: Joining Forces, Creating Value

ERIC Educational Resources Information Center

Kulpinski, Dan

2009-01-01

This publication presents in-depth profiles of six high-performing partnerships funded by the Partnership for a Nation of Learners (PNL) and short profiles of the remaining grantees. The partnerships illustrate a range of examples of how museums, libraries, public broadcasters, and other vital community organizations can collaborate to address…

Teaching "Red Scarf Girl". A Facing History and Ourselves Study Guide

ERIC Educational Resources Information Center

Kanner, Elisabeth Fieldstone

2009-01-01

Ji-li Jiang's extraordinary memoir "Red Scarf Girl" transports readers to a tumultuous time in Chinese history--the first two years of the Great Proletarian Cultural Revolution. Caught between conflicting forces--joining the Revolution's call for rebellion, protecting her family, and fitting in with her peers--Jiang describes how her…

After-School as Intermediary Space: Theory and Typology of Partnerships

ERIC Educational Resources Information Center

Noam, Gil G.; Tillinger, Jodi Rosenbaum

2004-01-01

People live in an era of partnering--of joining institutional forces to accomplish complex societal changes. Whether it is the local YMCA that works with a school to serve children during the afterschool hours, a university connecting with its surrounding community, or a city government convening funders and businesses, they are moving into…

Conceptual Evolution and Policy Developments in Lifelong Learning

ERIC Educational Resources Information Center

Yang, Jin, Ed.; Valdes-Cotera, Raul, Ed.

2011-01-01

In recognition of the status of the World Expo 2010 in Shanghai as a platform for exchange of ideas and experience in lifelong learning, UNESCO, the Shanghai Municipal People's Government, the Chinese Society of Educational Development Strategy and the Chinese National Commission for UNESCO joined forces to co-organise the Shanghai International…

Crossing the Aisle: Conversations about Collaboration

ERIC Educational Resources Information Center

Powell, Mark

2011-01-01

This article presents edited transcripts of separate Skype conversations with Richard Ungerer, AMS executive director, in his office at AMS headquarters in New York and Andre Roberfroid, president of AMI, at his home in Vetraz-Monthoux, France. It also presents a discussion of the ways the two organizations can join forces to strengthen the…

Powerful Allies: Arts Educators and Early Childhood Educators Joining Forces on Behalf of Young Children

ERIC Educational Resources Information Center

Baum, Angela C.

2017-01-01

Arts educators and early childhood educators espouse similar philosophies and purposes surrounding young children's educational lives, yet continue to function in largely separate worlds. This article calls for the creation of intentional alliances between the two disciplines, by first recognizing and embracing these alignments. In addition, this…

Using Social Media as a Tool for Learning: A Multi-Disciplinary Study

ERIC Educational Resources Information Center

Delello, Julie A.; McWhorter, Rochell R.; Camp, Kerri M.

2015-01-01

In order to explore the rich dynamics of using social media as a tool for learning within higher education classrooms, researchers across three disciplines: education, human resource development (HRD), and marketing, joined forces seeking ways to focus on learning through a retrospective analysis. Three concepts--engagement, community building,…

The GISt of GPS

ERIC Educational Resources Information Center

Lane, Kelly

2004-01-01

For the fourth year in a row, the author and a computer teacher have joined forces to guide students through an annual technology and research project that benefits area institutions and community members. The author presents the three key areas of the geospatial technologies curriculum at Douglas High School in Box Elder, South Dakota: (1)…

3 CFR 8491 - Proclamation 8491 of April 1, 2010. National Donate Life Month, 2010

Code of Federal Regulations, 2011 CFR

2011-01-01

... of circumstances through organ, tissue, stem cell, and blood donation. During National Donate Life... groups, and private organizations to join forces to boost the number of organ, tissue, blood, and stem cell donors throughout our Nation. IN WITNESS WHEREOF, I have hereunto set my hand this first day of...

Women in Military Aircrews: Possible Outlooks for the French Air Force

DTIC Science & Technology

1989-05-01

carefully implemented, because the current all-male environment is likely to be phychologically hostile. However, the system works very well in the... phychological barrier might be as much on the female side (for parochialistic reasons) as on the male side (who would perceive it as "downgrading" to join a

The One World of Working Women. Monograph No. 1.

ERIC Educational Resources Information Center

Nelson, Anne H.

Women of many nations, particularly the industrialized countries, are achieving greater opportunity and equality in the working world. The rate at which women are joining the work force has confounded all predictions and created unexpected difficulties in securing equal pay and access to jobs and training. The most direct discrimination, separate…

Internationalizing the Business Curriculum: Technology and Social Change.

ERIC Educational Resources Information Center

Seabrook, Roberta

In 1986 the Technology and Social Change Program and the College of Business at Iowa State University joined forces to develop a new graduate course that focused on the role of the multinational corporation in technology transfer to the lesser developed countries. The course was team taught by faculty from different disciplines and colleges, and…

Words for Work Report 2011/12: Evaluation Summary

ERIC Educational Resources Information Center

Melvin, Sally; Kenwright, Laura

2012-01-01

The National Literacy Trust's Words for Work programme is an innovative way for schools and businesses to join forces and address the nation's employability. Volunteers from the corporate world are partnered with secondary schools within their community to explore speaking and listening in the workplace through a range of workshops, aiming to…

Defense.gov Special Report: Veterans Day 2013

Science.gov Websites

Department of Defense Submit Search Veterans Day 2013 - Honoring our Nation's Veterans November 11, 2013 News Veterans Day at Arlington National Cemetery, calling the holiday a reminder of the nation's "sacred piece titled "Joining Forces with you on Veterans Day," First Lady Michelle Obama and Dr. Jill

WorkReady Philadelphia: Preparing Youth for Job Readiness

ERIC Educational Resources Information Center

Pawlowski, Brett

2010-01-01

One of the great concerns of the business community involves the workforce pipeline: employers want to be sure that new entries into the labor pool, whether from the K-12 or postsecondary systems, are prepared for the jobs that await them. In Philadelphia, business and community leaders have joined forces to give students workplace learning…

Vocational Preparation for Women: A Critical Analysis.

ERIC Educational Resources Information Center

Steiger, JoAnn

In this analysis of vocational preparation for women material is presented to substantiate the claim that women are joining the labor force in increasing numbers and their career opportunities are expanding, but that the educational system has failed to respond. Statistical data is cited showing that women have traditionally been employed in just…

Childhood exposure to violence and lifelong health: clinical intervention science and stress-biology research join forces.

PubMed

Moffitt, Terrie E

2013-11-01

Many young people who are mistreated by an adult, victimized by bullies, criminally assaulted, or who witness domestic violence react to this violence exposure by developing behavioral, emotional, or learning problems. What is less well known is that adverse experiences like violence exposure can lead to hidden physical alterations inside a child's body, alterations that may have adverse effects on life-long health. We discuss why this is important for the field of developmental psychopathology and for society, and we recommend that stress-biology research and intervention science join forces to tackle the problem. We examine the evidence base in relation to stress-sensitive measures for the body (inflammatory reactions, telomere erosion, epigenetic methylation, and gene expression) and brain (mental disorders, neuroimaging, and neuropsychological testing). We also review promising interventions for families, couples, and children that have been designed to reduce the effects of childhood violence exposure. We invite intervention scientists and stress-biology researchers to collaborate in adding stress-biology measures to randomized clinical trials of interventions intended to reduce effects of violence exposure and other traumas on young people.

Kelly Latimer

NASA Image and Video Library

2007-03-09

Kelly Latimer is a research pilot in the Flight Crew Branch of NASA's Dryden Flight Research Center, Edwards, Calif. Latimer joined NASA in March 2007 and will fly the T38, T-34, G-III, C-17 and the "Ikhana" Predator B. Latimer is Dryden's first female research test pilot. Prior to joining NASA, Latimer was on active duty with the U.S. Air Force. She has accumulated more than 5,000 hours of military and civilian flight experience in 30 aircraft. Latimer's first association with NASA was while attending graduate school at George Washington University, Washington, D.C. Her studies included work with the Joint Institute for the Advancement of Flight Sciences at NASA's Langley Research Center, Hampton, Va. She flew an Air Force C-17 during a 2005 NASA study to reduce aircraft noise. A team of California Polytechnic State University students and Northrop Grumman personnel were stationed on Rogers Dry Lake located at Edwards Air Force Base, Calif., to record the noise footprint of the aircraft as it made various landing approaches to Edwards' runway. Latimer completed undergraduate pilot training at Reese Air Force Base, Texas, in 1990. She remained at Reese as a T-38 instructor pilot until 1993. She was assigned as a C-141 aircraft commander at McCord Air Force Base, Tacoma, Wash., until 1996. Latimer graduated from the U.S. Air Force Test Pilot School at Edwards in Class 96B. She served as a C-17 and C-141 experimental test pilot at Edwards until 2000. She then became the chief of the Performance Branch and a T-38 instructor pilot at The Air Force Test Pilot School. She returned to McCord in 2002, where she was a C-17 aircraft commander and the operations officer for the 62nd Operations Support Squadron. In 2004, Latimer became the commander of Edwards' 418th Flight Test Squadron and director of the Global Reach Combined Test Force. Following that assignment, she deployed to Iraq as an advisor to the Iraqi Air Force. Her last active duty tour was as an instructor a

Dynamic analysis of four bar planar mechanism extended to six-bar planar mechanism with variable topology

NASA Astrophysics Data System (ADS)

Belleri, Basayya K.; Kerur, Shravankumar B.

2018-04-01

A computer-oriented procedure for solving the dynamic force analysis problem for general planar mechanisms is presented. This paper provides position analysis, velocity analysis, acceleration analysis and force analysis of six bar mechanism with variable topology approach. Six bar mechanism is constructed by joining two simple four bar mechanisms. Initially the position, velocity and acceleration analysis of first four bar mechanism are determined by using the input parameters. The outputs (angular displacement, velocity and acceleration of rocker)of first four bar mechanism are used as input parameter for the second four bar mechanism and the position, velocity, acceleration and forces are analyzed. With out-put parameters of second four-bar mechanism the force analysis of first four-bar mechanism is carried out.

Views of STS-9 crewmembers with families upon return to Ellington

NASA Technical Reports Server (NTRS)

1983-01-01

Astronaut John W. Young, STS-9 commander, is joined by his wife Susy at Ellington Air Force Base following arrival from the STS-9 landing site in southern California (45650); Astronaut Brewster H. Shaw Jr., STS-9 pilot, hugs his wife Kathleen and children Brewster III, right, Jessica and Brandon at ELlington AFB (45651).

Planting the Seeds of a New Agriculture: Living with the Land in Central America.

ERIC Educational Resources Information Center

Adriance, Jim

1995-01-01

Central America's macroeconomics, land tenure patterns, and population growth are forcing small-scale farmers to alternatives based on farmer-to-farmer teaching and farming in concert with the environment. Discusses major schools of thought that have fueled this phenomenon, and how extension services and isolated groups are joining to form a…

Joining Forces: Communities and Schools Working Together for a Change. A Special Report.

ERIC Educational Resources Information Center

Rugg, Carol D.

School and community partnerships form the very core of the Mott Foundation, as seen in its founding principles and its varied Civil Society, Flint, and Poverty programs. Although community education has evolved over the years to address increasingly serious problems, the work of today's community organizers is deeply rooted in past theories:…

Tubing crimping pliers

DOEpatents

Lindholm, G.T.

1981-02-27

The disclosure relates to pliers and more particularly to pliers for crimping two or more pieces of copper tubing together prior to their being permanently joined by brazing, soldering or the like. A die containing spring-loaded pins rotates within a cammed ring in the head of the pliers. As the die rotates, the pins force a crimp on tubing held within the pliers.

From Sea to Shining Sea

ERIC Educational Resources Information Center

Scott, Beverly

2005-01-01

Deep down in the depths of the sea, beautiful fish, mysterious ocean life, and unusual plants glimmer and glow in the eerie atmosphere of an ever-changing ocean. This article describes how, with this vision and a purpose in mind, three teachers pulled open classroom walls and joined forces so their second graders could create a mammoth 30 x 75"…

Mexico: Failing State or Emerging Democracy?

DTIC Science & Technology

2011-03-01

were dominated by The Institutional Revolutionary Party, or PRI. Mexican politics largely resembled the subliminally oppressive conditions... communications equipment, while Mexican security forces have only austere capabilities.27 The Mexican Federal Police and the Mexican Army killed...economic and government institutions. Mexico joins a community U.S. Defense Secretary Robert M. Gates, Chairman of the Joint Chiefs of Staff Admiral

"A Perfect Murder": An (Imperfect) School Theater Program Model

ERIC Educational Resources Information Center

Simon, Nicole S.; Grosso, Andrew

2009-01-01

Over the last five years, the Urban Assembly School for Law and Justice (SLJ), a new, small public high school in Brooklyn, and The Essentials, a professional theater company, have joined forces to offer a low-budget, high-quality, in-house afterschool theater program for SLJ students. Both SLJ and The Essentials were in nascent stages when the…

Online Tools Allow Distant Students to Collaborate on Research Projects

ERIC Educational Resources Information Center

T.H.E. Journal, 2005

2005-01-01

The Wesleyan Academy and Moravian School in St. Thomas, Virgin Islands, recently joined forces with Evergreen Elementary in Fort Lewis, Wash., to collaborate on a research project using My eCoach Online (http://myecoach.com) as the primary medium to share information, post ideas and findings, and develop inquiry projects on 10 topics about water.…

Cosmic Rays and Research in Schools: One School's Experience

ERIC Educational Resources Information Center

Chaffer, Andy; Tedd, Bernie

2016-01-01

The High School Project on Astrophysics Research with Cosmics (HiSPARC) is an international project in which secondary schools and academic institutions join forces to form a network of detectors to measure cosmic rays with extremely high energy. We present results of research done by students at the King Edward VI High School For Girls,…

Air Education and Training Command > Home

Science.gov Websites

Media Guide (PDF) USAF Social Media Sites Basic Training Technical Training AF Recruiting Service Flying Air Education and Training Command Air Education and Training Command Join the Air Force Home News Our Experts Search Air Education and Training Command: Continuum of Learning AETC Strategic Plan Ask

Reflections on Boycotts: An Open Letter to the Harvard Community.

ERIC Educational Resources Information Center

Bok, Derek C.

The question of what the university should do when it purchases goods and services from firms that are said to have acted improperly is considered by the president of Harvard University. It has been proposed that Harvard join national boycotts to force companies to stop engaging in specific practices that are thought to be improper. Several…

Planting People, Growing Justice: The Role of the New Social Justice Lawyer?

ERIC Educational Resources Information Center

Tyner, Artika Renee

2012-01-01

The process of social change draws upon the strength of many individuals to build a strong collective, develop a shared vision, exercise the power required to necessitate change, and join forces in solidarity. This study examined the role of one particular group in this process, lawyers, by identifying their leadership characteristics and…

Promising Practices in Young Adult Employment: Hands-On Multidisciplinary Career Exploration and Mentorships

ERIC Educational Resources Information Center

Wagner, Stacey

2015-01-01

The National Fund for Workforce Solution's Young Adult Initiatives aim to test and implement new strategies for targeting America's young adults and share this information so that employers and workforce development can join forces in investing in the millions of young adults across the nation. This case study focuses on promising findings from…

Minority Applicants to Colleges Will Rise Significantly by 2020

ERIC Educational Resources Information Center

Hoover, Eric

2013-01-01

Over the next decade, more students of color than ever before will pass through the gates of the nation's colleges and join the ranks of its work force, according to new projections by the Western Interstate Commission for Higher Education. By the year 2020, minority students will account for 45 percent of the nation's public high-school…

JPRS Report, East Europe

DTIC Science & Technology

1988-10-18

minority nation- alities, as well as international agreements concerning the reunification of families . There shall be no national- istic, chauvinist...deteriorating and they are worried about the upkeep of their families . In my opinion, this reflects their inner strength; they enable the...business has joined forces with nudists . There is a bra shortage. The insufficient supply of household appliances (washing machines, refrigera- tors

Joining Forces: A Collaborative Study of Curricular Integration

ERIC Educational Resources Information Center

Miller, Beth Ann

2013-01-01

The collaborative action research reported here strives to extend a prior study that dealt with the effects of integrating a general music course of study with the total curriculum of a first grade class. This second study used a similar plan in which a fifth grade teacher and a music teacher worked cooperatively to provide a curriculum that…

Wisconsin Youth Risk Behaviors: 1993 Survey Results. Bulletin No. 94305.

ERIC Educational Resources Information Center

Fernan, Steven A.; And Others

How can state leaders mobilize to meet the health and safety needs of its school-age children? To understand more about children's health, the Wisconsin Department of Public Instruction (DPI) has surveyed Wisconsin students. In 1993 the DPI and the U.S. Centers for Disease Control (CDC) joined forces to conduct the Youth Risk Behavior Survey.…

Team-Based Programs: The EMP. An Industry/University Partnership-The Educational Model for the 21st Century.

ERIC Educational Resources Information Center

Haynes, Ray; And Others

California Polytechnic State University's College of Business and College of Engineering have joined forces to create a joint Engineering Management Program (EMP). Students holding undergraduate engineering or equivalent degrees enter and earn both Masters in Business Administration and Masters of Science in Engineering in 24 months. The program…

Advancing Civic Learning and Engagement in Democracy: A Road Map and Call to Action

ERIC Educational Resources Information Center

US Department of Education, 2012

2012-01-01

Today, the U.S. Department of Education joins the National Task Force on Civic Learning and Democratic Engagement, the American Commonwealth Partnership, and the Campaign for the Civic Mission of Schools in a new national call to action to infuse and enhance civic learning and democratic engagement for all students throughout the American…

Cooperation with Commodity Groups and Hands-On Demonstrations Improve the Effectiveness of Commodity-Focused Educational Programs

ERIC Educational Resources Information Center

Kandel, Herman J.; Ransom, Joel K.; Torgerson, David A.; Wiersma, Jochum J.

2010-01-01

Wheat and soybean producers pay a small amount per bushel produced as a check-off. Funds are used for research, outreach, and crop promotion. Commodity organizations and Extension joined forces to develop multi-state educational outreach on spring wheat and soybean production. Participatory planning involved producers in developing these…

Promising Practices in Young Adult Employment: Lessons Learned from Manufacturing and Automotive Career Pathway Programs

ERIC Educational Resources Information Center

Wagner, Stacey

2015-01-01

The National Fund's Young Adult Initiatives aim to test and implement new strategies for targeting America's young adults and share this information so that employers and workforce development can join forces in investing in the millions of young adults across the nation. This case study focuses on promising findings from automotive and…

"Governing the Soul" through Remolding the Self: The American Approach

ERIC Educational Resources Information Center

Zhao, Guoping

2005-01-01

In this article, I trace historical events and thoughts that have joined forces in creating American cultural ways of "thinking about human beings and acting upon them." I suggest that while Foucault, Rose, and Popkewitz's work has demonstrated crucial parallels between the emergence of a new liberalism and a new way of governance --…

A water-cannon salute from two Air Force fire trucks heralds NASA research pilot Gordon Fullerton's final mission as his NASA F/A-18 taxis beneath the spray.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

Fracture resistance of inter-joined zirconia abutment of dental implant system with injection molding technique.

PubMed

Yang, Jianjun; Wang, Ke; Liu, Guangyuan; Wang, Dashan

2013-11-01

Zirconia powder in nanometers can be fabricated into inter-joined abutment of dental implant system with the injection shaping technique. This study was to detect the resistance of inter-joined zirconia abutment with different angle loading for clinical applications. The inter-joined abutments were shaped with the technique of injection of zirconia powder in nanometers. Sixty Osstem GSII 5 × 10 mm implants were used with 30 zirconia abutments and 30 Osstem GSII titanium abutments for fixation using 40 N torque force. The loading applications included 90°, 30°, and 0° formed by the long axis of abutments and pressure head of universal test machine. The fracture resistances of zirconia and titanium abutments were documented and analyzed. The inter-joined zirconia abutments were assembled to the Osstem GSII implants successfully. In the 90° loading mode, the fracture resistance of zirconia abutment group and titanium abutment group were 301.5 ± 15.4 N and 736.4 ± 120.1 N, respectively. And those in the 30° groups were 434.7 ± 36.1 N and 1073.1 ± 74 N, correspondingly. Significant difference in the two groups was found using t-test and Wilcoxon test. No damage on the abutments of the two groups but S-shaped bending on the implants was found when the 0° loading was 1300-2000 N. Through the assembly of Zirconia abutments and implants, all the components presented sufficient resistance acquired for the clinical application under loadings with different angle. © 2012 John Wiley & Sons A/S.

An Introduction to Service Learning Pedagogy

ERIC Educational Resources Information Center

Chenarani, Kiarash

2017-01-01

Many higher education institutions and discipline-specific associations have embraced service-learning as a way to join campuses (and specifically, academic departments across the curriculum) with their communities to positively respond to community challenges and opportunities for collaboration. Hundreds of definitions of service-learning exist…

Polar Attraction.

ERIC Educational Resources Information Center

Hoff, David J.

2001-01-01

Describes the experiences of a high school science teacher who joined a 5-week National Science Foundation research excursion to Antarctica that involved him as a participating researcher. The paper explains challenges that he encountered related to the physical environment, working conditions, and relationships with his colleagues. (SM)

Improving Self-Pierce Rivet Performance through Processing and Alloy Development

NASA Astrophysics Data System (ADS)

Van Hall, Stephen N.

Spot welding has been used to join steel sheet material in the past during automotive manufacturing. The increasing use of aluminum and mixed materials to achieve continually increasing fuel economy standards requires mechanical joining methods to provide adequate impact performance. One such mechanical joining process is self-pierce riveting (SPR). Self-pierce riveting has grown in popularity in recent years due to fast cycle times, high static strength and fatigue performance as well as the ability to join many different sheet material combinations. Self-pierce rivet utilization has become limited due to the material properties of the rivet in two main areas: the joining of high-strength sheet material and joining of multiple sheet material combinations using a single rivet geometry, referred to as commonization. Two specific case studies have been developed to assess the failures that occur and evaluate potential solutions: joining of press-hardened steel (PHS) to Al6111 and improved commonization ability using a two layer aluminum joint that is currently joined with a specialized rivet. Riveting trials have been performed on each of the two case studies using cold forged rivets produced from 10B37 steel that has been heat-treated through a quench and temper process to a range of hardness levels to evaluate the failures that occur within the rivet. The failures occur with two different modes: buckling of the rivet at hardness values below 550 HV when joining PHS and Al6111 and fractures that occur in the rivet tail at hardness values above 550 HV during joining in each of the case studies under evaluation. The fractures have been attributed to a high degree of hoop strain that forms when the rivets are flared beyond the design specifications. A method to replicate the rivet flaring procedure under laboratory conditions has been developed by flaring the rivets through various strain paths to induce a hoop strain and the resultant fractures. The flaring method shows the ability to replicate the types of fractures that were observed during joining attempts while monitoring applied force, crosshead displacement and strain at the point of fracture at the rivet tail using digital image correlation. Alternative alloys including 4130, 4340 and 5160 were evaluated alongside 10B37 for improved performance after quenching and tempering, austempering and after being intentionally decarburized to varying degrees. The heat-treatments were evaluated through microscopy, fractography, rivet flaring and joining attempts for each case study and alloy under investigation. All of the alternative alloys showed no significant performance gains after being quenched and tempered or austempered. However, hoop strain to failure during flaring was increased between 2-4x after the rivets had been intentionally decarburized. The intentionally decarburized rivets were evaluated through joining trials and provided successful joining for each of the case studies under investigation using 10B37 rivets. Rivets produced from 4340 and 5160 also showed instances of success during joining attempts. The Cockroft and Latham failure criterion was evaluated in regards to rivet flaring through the development of finite element simulations using Abaqus. The Cockroft and Latham failure criterion was able to successfully predict the location of riveting fractures through multiple strain paths, rivet geometries and microstructures. Cockroft and Latham values from tensile tests of 10B37 wire led to an underestimate of the strain to failure when compared to the rivet flaring process for quenched and tempered rivets but was very similar to the strain predicted for rivets that had been intentionally decarburized.

Causal reasoning with forces

PubMed Central

Wolff, Phillip; Barbey, Aron K.

2015-01-01

Causal composition allows people to generate new causal relations by combining existing causal knowledge. We introduce a new computational model of such reasoning, the force theory, which holds that people compose causal relations by simulating the processes that join forces in the world, and compare this theory with the mental model theory (Khemlani et al., 2014) and the causal model theory (Sloman et al., 2009), which explain causal composition on the basis of mental models and structural equations, respectively. In one experiment, the force theory was uniquely able to account for people's ability to compose causal relationships from complex animations of real-world events. In three additional experiments, the force theory did as well as or better than the other two theories in explaining the causal compositions people generated from linguistically presented causal relations. Implications for causal learning and the hierarchical structure of causal knowledge are discussed. PMID:25653611

Alleviation of whirl-flutter on a joined-wing tilt-rotor aircraft configuration using active controls

NASA Technical Reports Server (NTRS)

Vanaken, Johannes M.

1991-01-01

The feasibility of using active controls to delay the onset of whirl-flutter on a joined-wing tilt rotor aircraft was investigated. The CAMRAD/JA code was used to obtain a set of linear differential equations which describe the motion of the joined-wing tilt-rotor aircraft. The hub motions due to wing/body motion is a standard input to CAMRAD/JA and were obtained from a structural dynamics model of a representative joined-wing tilt-rotor aircraft. The CAMRAD/JA output, consisting of the open-loop system matrices, and the airframe free vibration motion were input to a separate program which performed the closed-loop, active control calculations. An eigenvalue analysis was performed to determine the flutter stability of both open- and closed-loop systems. Sensor models, based upon the feedback of pure state variables and based upon hub-mounted sensors, providing physically measurable accelerations, were evaluated. It was shown that the onset of tilt-rotor whirl-flutter could be delayed from 240 to above 270 knots by feeding back vertical and span-wise accelerations, measured at the rotor hub, to the longitudinal cyclic pitch. Time response calculations at a 270-knot cruise condition showed an active cyclic pitch control level of 0.009 deg, which equates to a very acceptable 9 pound active-control force applied at the rotor hub.

Fabrication and characterization of joined silicon carbide cylindrical components for nuclear applications

NASA Astrophysics Data System (ADS)

Khalifa, H. E.; Deck, C. P.; Gutierrez, O.; Jacobsen, G. M.; Back, C. A.

2015-02-01

The use of silicon carbide (SiC) composites as structural materials in nuclear applications necessitates the development of a viable joining method. One critical application for nuclear-grade joining is the sealing of fuel within a cylindrical cladding. This paper demonstrates cylindrical joint feasibility using a low activation nuclear-grade joint material comprised entirely of β-SiC. While many papers have considered joining material, this paper takes into consideration the joint geometry and component form factor, as well as the material performance. Work focused specifically on characterizing the strength and permeability performance of joints between cylindrical SiC-SiC composites and monolithic SiC endplugs. The effects of environment and neutron irradiation were not evaluated in this study. Joint test specimens of different geometries were evaluated in their as-fabricated state, as well as after being subjected to thermal cycling and partial mechanical loading. A butted scarf geometry supplied the best combination of high strength and low permeability. A leak rate performance of 2 × 10-9 mbar l s-1 was maintained after thermal cycling and partial mechanical loading and sustained applied force of 3.4 kN, or an apparent strength of 77 MPa. This work shows that a cylindrical SiC-SiC composite tube sealed with a butted scarf endplug provides out-of-pile strength and permeability performance that meets light water reactor design requirements.

Joining the Dots: The Challenge of Creating Coherent School Improvement

ERIC Educational Resources Information Center

Robinson, Viviane; Bendikson, Linda; McNaughton, Stuart; Wilson, Aaron; Zhu, Tong

2017-01-01

Background/Context: Sustained school improvement requires adequate organizational and instructional coherence, yet, in typical high schools, subject department organization, norms of teacher professional autonomy, and involvement in multiple initiatives present powerful obstacles to forging a coherent approach to improvement. This study examines…

Welding--Trade or Profession?

ERIC Educational Resources Information Center

Albright, C. E.; Smith, Kenneth

2006-01-01

This article discusses a collaborative program between schools with the purpose of training and providing advanced education in welding. Modern manufacturing is turning to automation to increase productivity, but it can be a great challenge to program robots and other computer-controlled welding and joining systems. Computer programming and…

Hong Kong children's posited "vulnerability" to social influence on substance abuse.

PubMed

Cheung, Chau-Kiu; Tse, John Wing-Ling

2008-01-01

A survey of 2,051 pupils between Grade 4 and Grade 7 in 2003 showed that social influence or encouragement to substance use was a significant determinant of substance use risk, controlling for prior substance use and other backgrounds. Contextual stress or unhappiness among parents, classmates, and other people around operated jointly with social influence to promote substance use risk. This finding accords with a dovetail model about the extra influence due to the joining of force and receptivity to the force. Further research is necessary to corroborate the present findings obtained from a place and a time.

KSC-2011-1095

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- At Vandenberg Air Force Base in California, the protective payload fairing that will surround NASA's Glory spacecraft arrives at the Astrotech payload processing facility. Once encapsulated, the spacecraft will be transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1380

NASA Image and Video Library

2011-02-05

VANDENBERG AIR FORCE BASE, Calif. -- At Vandenberg Air Force Base in California, technicians join NASA's Glory spacecraft with the Taurus XL rocket's third stage, housed inside a temporary processing tent near the pad at Space Launch Complex 576-E. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Randy Beaudoin, VAFB

KSC-2011-1096

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- At Vandenberg Air Force Base in California, the protective payload fairing that will surround NASA's Glory spacecraft arrives at the Astrotech payload processing facility. Once encapsulated, the spacecraft will be transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1094

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- At Vandenberg Air Force Base in California, the protective payload fairing that will surround NASA's Glory spacecraft arrives at the Astrotech payload processing facility. Once encapsulated, the spacecraft will be transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

Joining of polymer-metal lightweight structures using self-piercing riveting (SPR) technique: Numerical approach and simulation results

NASA Astrophysics Data System (ADS)

Amro, Elias; Kouadri-Henni, Afia

2018-05-01

Restrictions in pollutant emissions dictated at the European Commission level in the past few years have urged mass production car manufacturers to engage rapidly several strategies in order to reduce significantly the energy consumption of their vehicles. One of the most relevant taken action is light-weighting of body in white (BIW) structures, concretely visible with the increased introduction of polymer-based composite materials reinforced by carbon/glass fibers. However, the design and manufacturing of such "hybrid" structures is limiting the use of conventional assembly techniques like resistance spot welding (RSW) which are not transferable as they are for polymer-metal joining. This research aims at developing a joining technique that would eventually enable the assembly of a sheet molding compound (SMC) polyester thermoset-made component on a structure composed of several high strength steel grades. The state of the art of polymer-metal joining techniques highlighted the few ones potentially able to respond to the industrial challenge, which are: structural bonding, self-piercing riveting (SPR), direct laser joining and friction spot welding (FSpW). In this study, the promising SPR technique is investigated. Modelling of SPR process in the case of polymer-metal joining was performed through the building of a 2D axisymmetric FE model using the commercial code Abaqus CAE 6.10-1. Details of the numerical approach are presented with a particular attention to the composite sheet for which Mori-Tanaka's homogenization method is used in order to estimate overall mechanical properties. Large deformations induced by the riveting process are enabled with the use of a mixed finite element formulation ALE (arbitrary Lagrangian-Eulerian). FE model predictions are compared with experimental data followed by a discussion.

College and Career Ready: Preparing Students in Fitness and Health Literacy

ERIC Educational Resources Information Center

Buskist, Connie; Reilly, Erin; Walker, Andria; Bourke, Nicholas

2016-01-01

The Common Core State Standards (CCSS) for English language arts have been adopted by many states across the country in an effort to prepare students for life after high school, whether that be going to college or joining the work force. The anchor standards of the CCSS, known as the College and Career Ready Standards, describe the literacy skills…

National Cancer Institute and American Association for Clinical Chemistry Partner to Bridge the Gap | Office of Cancer Clinical Proteomics Research

Cancer.gov

The National Cancer Institute, through its Clinical Proteomic Technologies for Cancer (CPTC) initiative has entered into a memorandum of understanding with the American Association for Clinical Chemistry (AACC) to join forces to promote and educate the clinical chemistry community in the area of proteomic standards and technology advances.

NREL Innovation Improves Safety of Electric Vehicle Batteries | News | NREL

Science.gov Websites

spacesuits and EDVs led NREL to join forces with NASA in finding new, more precise ways to trigger internal . Now, the resulting first-of-its-kind ISC device is being used by NREL, NASA, and manufacturers to study battery responses to these latent flaws and determine solutions. "The trials with NASA have

Kelly at SSRMS controls in Destiny laboratory module

NASA Image and Video Library

2005-08-05

S114-E-7484 (5 August 2005) --- Astronaut James M. Kelly, STS-114 pilot, works in the Destiny laboratory of the International Space Station while Space Shuttle Discovery was docked to the Station. Astronauts Kelly and Wendy B. Lawrence (out of frame), mission specialist, joined forces to re-stow the Italian-built Raffaello Multi-Purpose Logistics Module (MPLM) in the cargo bay.

Public-Private Partnership. An Opportunity for Urban Communities. A Statement by the Research and Policy Committee of the Committee for Economic Development.

ERIC Educational Resources Information Center

Committee for Economic Development, New York, NY. Research and Policy Committee.

In this era of constrained resources, the public and private sectors must join forces to revitalize their local urban communities. Public-private partnership means cooperation among individuals and organizations in the public and private sectors for mutual benefit. Such cooperation has two dimensions--the policy dimension and the operational…

Childhood exposure to violence and lifelong health: Clinical intervention science and stress biology research join forces

PubMed Central

Moffitt, Terrie E.

2013-01-01

Many young people who are mistreated by an adult, victimized by bullies, criminally assaulted, or who witness domestic violence react to this violence exposure by developing behavioral, emotional, or learning problems. What is less well known is that adverse experiences like violence exposure can lead to hidden physical alterations inside a child’s body, alterations which may have adverse effects on life-long health. We discuss why this is important for the field of developmental psychopathology and for society, and we recommend that stress-biology research and intervention science join forces to tackle the problem. We examine the evidence base in relation to stress-sensitive measures for the body (inflammatory reactions, telomere erosion, epigenetic methylation, and gene expression) and brain (mental disorders, neuroimaging, and neuropsychological testing). We also review promising interventions for families, couples, and children that have been designed to reduce the effects of childhood violence exposure. We invite intervention scientists and stress-biology researchers to collaborate in adding stress-biology measures to randomized clinical trials of interventions intended to reduce effects of violence exposure and other traumas on young people. PMID:24342859

Hearing Device Manufacturers Call for Interoperability and Standardization of Internet and Audiology.

PubMed

Laplante-Lévesque, Ariane; Abrams, Harvey; Bülow, Maja; Lunner, Thomas; Nelson, John; Riis, Søren Kamaric; Vanpoucke, Filiep

2016-10-01

This article describes the perspectives of hearing device manufacturers regarding the exciting developments that the Internet makes possible. Specifically, it proposes to join forces toward interoperability and standardization of Internet and audiology. A summary of why such a collaborative effort is required is provided from historical and scientific perspectives. A roadmap toward interoperability and standardization is proposed. Information and communication technologies improve the flow of health care data and pave the way to better health care. However, hearing-related products, features, and services are notoriously heterogeneous and incompatible with other health care systems (no interoperability). Standardization is the process of developing and implementing technical standards (e.g., Noah hearing database). All parties involved in interoperability and standardization realize mutual gains by making mutually consistent decisions. De jure (officially endorsed) standards can be developed in collaboration with large national health care systems as well as spokespeople for hearing care professionals and hearing device users. The roadmap covers mutual collaboration; data privacy, security, and ownership; compliance with current regulations; scalability and modularity; and the scope of interoperability and standards. We propose to join forces to pave the way to the interoperable Internet and audiology products, features, and services that the world needs.

Investigation of Coating and Corrosion Mitigation Strategies in Magnesium/Mixed Metal Assemblies

NASA Astrophysics Data System (ADS)

Forsmark, Joy H.; McCune, Robert C.; Giles, Terry; Audette, Michelle; Snowden, Jasmine; Stalker, Jeff; Morey, Matthew; O'Keefe, Matt; Castano, Carlos

The US Automotive Materials Partnership through the Magnesium-Intensive Front End Development Project (MFERD) is currently investigating a number of joining, coating and corrosion mitigation strategies to incorporate magnesium components into the automotive body-in-white with the ultimate goal of decreasing vehicle curb weight, thus improving fuel economy. Because Mg is anodic to all other structural metals, this is a key hurdle to Mg component implementation in vehicles. This paper will discuss the results of a study to examine the effectiveness of different corrosion mitigation strategies in joined plate assemblies and provide some insight into the systems challenges of incorporation of Mg parts into a vehicle. Details of a statistically-designed experiment developed to explore the interaction of several materials of construction (magnesium, steel and aluminum), pretreatment and topcoatings, joining methods and standardized test protocols including SAE J-2334 and ASTM B-117 are discussed. A number of avenues have emerged from this study as potential strategies for corrosion mitigation.

Layup Configuration Effect on Notch Residual Strength in Composite Laminates

PubMed Central

Santhanakrishnan Balakrishnan, Venkateswaran; Seidlitz, Holger

2018-01-01

The current trend shows an increasing demand for composites due to their high stiffness to weight ratio and the recent progress in manufacturing and cost reduction of composites. To combine high strength and stiffness in a cost-effective way, composites are often joined with steel or aluminum. However, joining of thermoset composite materials is challenging because circular holes are often used to join them with their metal counterparts. These design based circular holes induce high stress concentration around the hole. The purpose of this paper is to focus on layup configuration and its impact on notch stress distribution. To ensure high quality and uniformity, the holes were machined by a 5 kW continuous wave (cw) CO2 laser. The stress distribution was evaluated and compared by using finite element analysis and Lekhnitskii’s equations. For further understanding, the notch strength of the laminates was compared and strain distributions were analyzed using the digital image correlation technique. PMID:29461492

Joining psychiatric care and faith healing in a prayer camp in Ghana: randomised trial.

PubMed

Ofori-Atta, A; Attafuah, J; Jack, H; Baning, F; Rosenheck, R

2018-01-01

Care of people with serious mental illness in prayer camps in low-income countries generates human rights concerns and ethical challenges for outcome researchers. Aims To ethically evaluate joining traditional faith healing with psychiatric care including medications (Clinical trials.gov identifier NCT02593734). Residents of a Ghana prayer camp were randomly assigned to receive either indicated medication for schizophrenia or mood disorders along with usual prayer camp activities (prayers, chain restraints and fasting) (n = 71); or the prayer camp activities alone (n = 68). Masked psychologists assessed Brief Psychiatric Rating Scale (BPRS) outcomes at 2, 4 and 6 weeks. Researchers discouraged use of chaining, but chaining decisions remained under the control of prayer camp staff. Total BPRS symptoms were significantly lower in the experimental group (P = 0.003, effect size -0.48). There was no significant difference in days in chains. Joining psychiatric and prayer camp care brought symptom benefits but, in the short-run, did not significantly reduce days spent in chains. Declaration of interest None.

Obstacles and opportunities in Chinese pharmaceutical innovation.

PubMed

Ni, Jingyun; Zhao, Junrui; Ung, Carolina Oi Lam; Hu, Yuanjia; Hu, Hao; Wang, Yitao

2017-03-24

Global healthcare innovation networks nowadays have expanded beyond developed countries with many developing countries joining the force and becoming important players. China, in particular, has seen a significant increase in the number of innovative firms and research organizations stepping up to the global network in recent years. Nevertheless, the intense Research and Development input has not brought about the expectable output. While China is ascending at a great speed to a leading position worldwide in terms of Research and Development investment, scientific publications and patents, the innovation capabilities in the pharmaceutical sector remain weak. This study discusses the challenges and opportunities for pharmaceutical innovation in China. One hand, academic, industrial, institutional and financial constraints were found to be the major and inevitable barriers hindering the development of drug innovation. On the other hand, unique advantages had been observed which included growing pharmaceutical market, Research and Development funding, distinctive source, and international cooperation. The most important thing for China's pharmaceutical sector to leap forward is to break though innovation barriers and integrate own advantages into global value-chain of healthcare product development.

e-Care integration: To meet the demographic challenge.

PubMed

Manning, Bryan R M; McKeon Stosuy, Mary

2006-01-01

Current multi-agency models of care will be wholly unsustainable when faced with the forecast doubling of over 65s in the developed and developing nations to around 40% of their populations of the next decades. The resulting imbalance between demand and skilled resources is beginning to force radical change towards a fully "joined up" cross-disciplinary, cross-agency service that spans the wide spectrum of medical and social care. This paper offers a basis for a radically revised model that combines end-to-end service processes optimization; the use of integrated assistive technology systems to help the elderly maintain an independent lifestyle; personal risk reduction through medical and status monitoring; extended care-watch and service co-ordination. It then develops an IPTV based approach to provide the necessary infrastructure to underpin provision of these facilities both at home and in the community. These substantial benefits are reviewed and weighed against the inherent loss of privacy that can result from the pervasive computing aspects of the care watch approach, together with the trust building and change management aspects that are inevitably involved in the rationalisation process.

Researching Gender Professions: Nurses as Professionals

ERIC Educational Resources Information Center

Zufiaurre, Benjamin; de Villarreal, Maider Pérez

2018-01-01

Nurses as professionals of health, childhood education teachers, social workers and caregivers, join a group of "feminine professions" which grew through policies of a welfare state in postwar constructive period, or in times of postwar accords (Jones, 1983). These professions are under challenge because of neoliberal policies and…

Naval Sea Systems Command > Home

Science.gov Websites

Parties Vehicles for Partnering STEM Programs FIRST LEGO League Robotics Program Carderock Math Contest Educational Partnership Agreements Math Clubs Seaplane Challenge Calculator-Controlled Robot Program Students - 'Fun Twist on Math' May 24, 2018 More SOCIAL MEDIA Facebook Logo Join us live as we commission

RCN faces challenges over rising inequalities within profession.

PubMed

Owen, Michael

2014-08-19

It is difficult to understand why the RCN will not join colleagues in the Royal College of Midwives and other health unions in balloting members on industrial action (Editorial and News July 30). Is the RCN fearful of the outcome should the response be a yes?

Voluntary Group Participation by Third Age Australians.

ERIC Educational Resources Information Center

Mayhew, Claire; Swindell, Rick

A study investigated characteristics of retirees and types of voluntary groups they joined after retirement. Data were collected through face-to-face interviews and completed questionnaires of 206 Australians over age 50. Five categories of voluntary organizations were studied: intellectually challenging, sporting/exercise, social, helping others,…

Aligning for Heroes: Partnership for Veteran Care in New Hampshire.

PubMed

Fasoli, DiJon R

2015-01-01

A growing number of veterans and service members ("veterans" refers to both veterans and eligible service members) are returning home and may be living with mental health conditions related to their military service. For a variety of reasons, the majority of US veterans receive their health care outside the Veterans Administration or the military health system. Nurse leaders and citizen-soldiers were among a number of concerned government officials, health care professionals, service providers, and military leaders in New Hampshire (NH) who joined forces to explore NH veterans' mental health needs and manage provider service capacity. This article describes the formation and efforts of a permanent legislative commission, the NH Commission on PTSD and TBI (COPT), composed of interdisciplinary, multiorganizational, and cross-governmental leaders aligned to address the issues of stigma, military cultural awareness, and integration of care. Commission participants were asked to share their perspectives on the gaps and challenges to veterans' care, opportunities for collaboration, and measurable outcomes. Key challenges included interagency communication and care integration issues, veteran and provider knowledge gaps about needs and system problems. Favorable timing, available funding, and the collaborative environment of the commission were identified as potential opportunities. While still a work in progress, the COPT has begun making an impact. We identify early outcomes and lessons learned. The COPT is a model for leveraging interdisciplinary professional collaboration to improve access to care for veterans.

Cross-Electrophile Coupling: Principles of Reactivity and Selectivity

PubMed Central

2015-01-01

A critical overview of the catalytic joining of two different electrophiles, cross-electrophile coupling (XEC), is presented with an emphasis on the central challenge of cross-selectivity. Recent synthetic advances and mechanistic studies have shed light on four possible methods for overcoming this challenge: (1) employing an excess of one reagent; (2) electronic differentiation of starting materials; (3) catalyst–substrate steric matching; and (4) radical chain processes. Each method is described using examples from the recent literature. PMID:24820397

The national response for preventing healthcare-associated infections: research and adoption of prevention practices.

PubMed

Kahn, Katherine L; Mendel, Peter; Leuschner, Kristin J; Hiatt, Liisa; Gall, Elizabeth M; Siegel, Sari; Weinberg, Daniel A

2014-02-01

Healthcare-associated infections (HAIs) have long been the subject of research and prevention practice. When findings show potential to significantly impact outcomes, clinicians, policymakers, safety experts, and stakeholders seek to bridge the gap between research and practice by identifying mechanisms and assigning responsibility for translating research to practice. This paper describes progress and challenges in HAI research and prevention practices, as explained through an examination of Health and Human Services (HHS) Action Plan's goals, inputs, and implementation in each area. We used the Context-Input-Process-Product evaluation model, together with an HAI prevention system framework, to assess the transformative processes associated with HAI research and adoption of prevention practices. Since the introduction of the Action Plan, HHS has made substantial progress in prioritizing research projects, translating findings from those projects into practice, and designing and implementing research projects in multisite practice settings. Research has emphasized the basic science and epidemiology of HAIs, the identification of gaps in research, and implementation science. The basic, epidemiological, and implementation science communities have joined forces to better define mechanisms and responsibilities for translating HAI research into practice. Challenges include the ongoing need for better evidence about intervention effectiveness, the growing implementation burden on healthcare providers and organizations, and challenges implementing certain practices. Although these HAI research and prevention practice activities are complex spanning multiple system functions and properties, HHS is making progress so that the right methods for addressing complex HAI problems at the interface of patient safety and clinical practice can emerge.

Two Basic Scientists Walk into a Translational Space.

PubMed

2017-09-21

When John Schiller first joined Douglas Lowy's lab at the National Cancer Institute of the NIH, he could have not predicted that their common interest in the molecular biology of oncogenes would set them in path for discoveries that ultimately enabled the development of a vaccine for the human papillomavirus, which causes the majority of cervical cancers worldwide. John and Doug, the recipients of the 2017 Lasker-DeBakey Clinical Award, have joined Cell editor João Monteiro in a Conversation about science, public health, and the joys and challenges of being basic scientists in a translational space. Annotated excerpts from this conversation are presented below. Copyright © 2017. Published by Elsevier Inc.

Assesment of influncing factors on mechanical and electrical properties of Al/Cu joints

NASA Astrophysics Data System (ADS)

Selvaraj, R. Meby; Hynes, N. Rajesh Jesudoss

2018-05-01

Joining of dissimilar materials opens up challenging opportunities in todays technology. Al/Cu weldments are used in applications that demands corrosion resistance, thermal and electrical conducting properties. In dissimilar joining mechanical and thermal properties result in large stress gradients during heating. The Al-Cu joints are lighter, cheaper and have conductivity equal to copper alloy. The main scope of this study is to assess the influencing factors of Al/Cu joints in mechanical and electrical properties. It includes the influence of the dilution between the base metals, influence of physical properties, influence of welding parameters, influence of filler metal, influence of heat treatment, and influence of electrical properties

Joining and interconnect formation of nanowires and carbon nanotubes for nanoelectronics and nanosystems.

PubMed

Cui, Qingzhou; Gao, Fan; Mukherjee, Subhadeep; Gu, Zhiyong

2009-06-01

Interconnect formation is critical for the assembly and integration of nanocomponents to enable nanoelectronics- and nanosystems-related applications. Recent progress on joining and interconnect formation of key nanomaterials, especially nanowires and carbon nanotubes, into functional circuits and/or prototype devices is reviewed. The nanosoldering technique through nanoscale lead-free solders is discussed in more detail in this Review. Various strategies of fabricating lead-free nanosolders and the utilization of the nanosoldering technique to form functional solder joints are reviewed, and related challenges facing the nanosoldering technique are discussed. A perspective is given for using lead-free nanosolders and the nanosoldering technique for the construction of complex and/or hybrid nanoelectronics and nanosystems.

Retired NASA research pilot and former astronaut Gordon Fullerton was greeted by scores of NASA Dryden staff who bid him farewell after his final NASA flight.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

Two NASA Dryden F/A-18s flown by Gordon Fullerton and Nils Larson fly in tight formation Dec. 21, 2007 during Fullerton's final flight before his retirement.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

Nils Larson

NASA Image and Video Library

2007-03-16

Nils Larson is a research pilot in the Flight Crew Branch of NASA's Dryden Flight Research Center, Edwards, Calif. Larson joined NASA in February 2007 and will fly the F-15, F-18, T-38 and ER-2. Prior to joining NASA, Larson was on active duty with the U.S. Air Force. He has accumulated more that 4,900 hours of military and civilian flight experience in more than 70 fixed and rotary winged aircraft. Larson completed undergraduate pilot training at Williams Air Force Base, Chandler, Ariz., in 1987. He remained at Williams as a T-37 instructor pilot. In 1991, Larson was assigned to Beale Air Force Base, Calif., as a U-2 pilot. He flew 88 operational missions from Korea, Saudi Arabia, the United Kingdom, Panama and other locations. Larson graduated from the U.S. Air Force Test Pilot School at Edwards Air Force Base, Calif., in Class 95A. He became a flight commander and assistant operations officer for the 445th squadron at Edwards. He flew the radar, avionics integration and engine tests in F-15 A-D, the early flights of the glass cockpit T-38C and airworthiness flights of the Coast Guard RU-38. He was selected to serve as an Air Force exchange instructor at the U.S. Naval Test Pilot School, Patuxent River, Md. He taught systems and fixed-wing flight test and flew as an instructor pilot in the F-18, T-2, U-6A Beaver and X-26 Schweizer sailplane. Larson commanded U-2 operations for Warner Robins Air Logistics Center's Detachment 2 located in Palmdale, Calif. In addition to flying the U-2, Larson supervised the aircraft's depot maintenance and flight test. He was the deputy group commander for the 412th Operations Group at Edwards before retiring from active duty in 2007 with the rank of lieutenant colonel. His first experience with NASA was at the Glenn Research Center, Cleveland, where he served a college summer internship working on arcjet engines. Larson is a native of Bethany, W.Va,, and received his commission from the U.S. Air Force Academy in 1986 with a

Reciprocal Distancing: A Systems Model of Interpersonal Processes in Cross-Cultural Consultation.

ERIC Educational Resources Information Center

Maital, Sharone L.

2000-01-01

A longitudinal consultation project with teachers in an early education program for Ethiopian immigrant children in Israel is presented to illustrate the application of the reciprocal distancing model in cross-cultural consultation. Evidence for disengagement as well as joining of teachers and challenging children despite frustration and…

Dental Education in Europe: The Challenges of Variety.

ERIC Educational Resources Information Center

Scott, John

2003-01-01

Finds that dental education varies considerably across Europe, with differing traditions of stomatology and odontology. The European Union's Dental Directives are often poorly followed by individual schools, and differences will likely intensify as Eastern/Central European countries join. The DentEd Thematic Network Project, which aims to promote…

On Sentimental Education among American College Students

ERIC Educational Resources Information Center

Sabin, Portia Culver

2007-01-01

Background/Context: This study attempts to join the debate around the definition of "education" by looking at it as an ongoing, everyday social practice. It follows decades of work done on "love" in America and opens an inquiry into "friendship" as a product of situated practical action. It also challenges social…

Join the Hive: The Need for More "Hybrid" Educators

ERIC Educational Resources Information Center

Giusto, Michelle

2015-01-01

Challenging the dichotomy between theory and practice in education, the author advocates a middle ground that could motivate more practicing teachers to pursue the studies necessary to become "hybrid" educators. These teacher educators would be masters of both research and practice, bringing both into teacher preparation programs in a…

The Techy Teacher/Join the TED-Ed Club

ERIC Educational Resources Information Center

Tucker, Catlin

2016-01-01

Classrooms exist in an insular environment, and the work done there often feels disconnected from students' lives, interests, and hobbies. However, students today must cultivate the ability to navigate an increasingly connected global society. Global-ready graduates must be able to tackle real-world challenges, publish their work online, and…

Information Portals: The Next Generation Catalog

ERIC Educational Resources Information Center

Allison, DeeAnn

2010-01-01

Libraries today face an increasing challenge: to provide relevant information to diverse populations with differing needs while competing with Web search engines like Google. In 2009, a large group of libraries, including the University of Nebraska-Lincoln Libraries, joined with Innovative Interfaces as development partners to design a new type of…

Principals Make Assignments Matter

ERIC Educational Resources Information Center

Dougherty, Eleanor

2013-01-01

The inner-city high school in Washington, DC, that Guillaume Gendre joined as an assistant principal had a modest reputation for achievement but was nevertheless challenged to raise expectations for student work. In other schools, Gendre had used assignments--a specific kind of instructional task in which students are charged to think about an…

AN EXPLORATORY INVESTIGATION OF SELECTED STUDENT TYPES AT THREE UNIVERSITY OF CALIFORNIA CAMPUSES, A PRELIMINARY REPORT.

ERIC Educational Resources Information Center

MOCK, KATHLEEN; AND OTHERS

A CONCERN OVER THE LOSS OF POTENTIALLY CAPABLE STUDENTS LED RESEARCH PERSONNEL ON THE DAVIS, LOS ANGELES, AND SANTA BARBARA CAMPUSES OF THE UNIVERSITY OF CALIFORNIA TO JOIN FORCES IN A STUDY TO IDENTIFY WAYS FOR ACCOMMODATING THE VARIOUS TYPES OF STUDENTS ADMITTED TO THE THREE SCHOOLS. A 2-YEAR PROJECT WAS PLANNED. THIS INTERIM REPORT COVERED A…

Inside KSC! for May 11, 2018

NASA Image and Video Library

2018-05-11

NASA’s InSight spacecraft is on a six-month, 300-million mile voyage to Mars, following a successful liftoff from Vandenberg Air Force Base in California on May 5. “The Voice of Kennedy Launch Control” now has a place on the “Chroniclers wall.” George Diller joined the prestigious “Chroniclers” group during a ceremony at Kennedy’s NASA News Center on May 4.

GSD Update: It works both ways: How scientists and managers join forces to conserve today’s natural resources

Treesearch

Karen Bagne; Deborah Finch

2012-01-01

Helping managers to promote sustainability on the Nation's forests and grasslands has been an overarching goal of US Forest Service Research and Development from the agency's beginnings in 1905. Major advances in resource management have been made with the help of science, from increasing yields of commodities like timber and cattle to providing services such...

Electro-mechanical heat switch for cryogenic applications

DOEpatents

van den Berg, Marcel L.; Batteux, Jan D.; Labov, Simon E.

2003-01-01

A heat switch includes two symmetric jaws. Each jaw is comprised of a link connected at a translatable joint to a flexible arm. Each arm rotates about a fixed pivot, and has an articulated end including a thermal contact pad connected to a heat sink. The links are joined together at a translatable main joint. To close the heat switch, a closing solenoid is actuated and forces the main joint to an over-center position. This movement rotates the arms about their pivots, respectively, forces each of them into a stressed configuration, and forces the thermal contact pads towards each other and into compressive contact with a cold finger. The closing solenoid is then deactivated. The heat switch remains closed due to a restoring force generated by the stressed configuration of each arm, until actuation of an opening solenoid returns the main joint to its starting open-switch position.

Community-based Participatory Research

PubMed Central

Holkup, Patricia A.; Tripp-Reimer, Toni; Salois, Emily Matt; Weinert, Clarann

2009-01-01

Community-based participatory research (CBPR), with its emphasis on joining with the community as full and equal partners in all phases of the research process, makes it an appealing model for research with vulnerable populations. However, the CBPR approach is not without special challenges relating to ethical, cultural, and scientific issues. In this article, we describe how we managed the challenges we encountered while conducting a CBPR project with a Native American community. We also suggest criteria that will enable evaluation of the project. PMID:15455579

Effects of processing parameters on the friction stir spot joining of Al5083-O aluminum alloy to DP590 steel

NASA Astrophysics Data System (ADS)

Sung, Back-Sub; Bang, Hee-Seon; Jeong, Su-Ok; Choi, Woo-Seong; Kwon, Yong-Hyuk; Bang, Han-Sur

2017-05-01

Two dissimilar materials, aluminum alloy Al5083-O and advanced high strength steel DP590, were successfully joined by using friction stir spot joining (FSSJ). Satisfactory joint strengths were obtained at a rotational speed of 300 rpm and a plunge depth of 0.7 mm. Resulting joints were welded without a non-welded zone. This may be attributed to the enhanced smooth material flow owing to sufficient stirring effect and tool down force between the upper Al5083-O side and the lower DP590 side. The maximum tensile shear strength was 6.5 kN, which was higher than the joint strength required by the conventional method of resistance spot welding. The main fracture mode was plug fracture in the tensile shear test of joints. An intermetallic compound (IMC) layer with <6 μm thickness was formed at the joint interface, which meets the allowance value of <10 μm for the dissimilar material Al-Fe joints. Thus, the use of FSSJ to weld the dissimilar materials Al5083-O and DP590 resulted in mechanically and metallurgically sound joints.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohmi, Tatsuya; Matsuura, Kiyotaka; Iguchi, Manabu

A centrifugal combustion synthesis (CCS) process has been investigated to join a Ni-Al intermetallic compound and a Ni-TiC cermet. The cermet, a tubular graphite mold, and a green compact of reactants consisting of Al, Ni and NiO were set in a centrifugal caster. When the combustion synthesis reaction was induced in the centrifugal force field, a synthesized molten Ni-Al alloy flowed into the graphite mold and joined to the cermet. The soundness of the joint interface depended on the volume percentage of TiC phase in the cermet. A lot of defects were formed near the interface between the Ni-TiC cermetmore » and the cast Ni-Al alloy when the volume percentage of TiC was 50% or higher. For this kind of cermet system, using a functionally graded cermet such as Ni-10 vol.%TiC/Ni-25 vol.%TiC/Ni-50 vol.%TiC overcame this difficulty. The four-point bending strength of the joined specimen consisting of the three-layered FGM cermet and cast Ni-29 mol%Al alloy was 1010 MPa which is close to the result for a Ni-29 mol%Al alloy specimen.« less

KSC-2011-1093

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1091

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1085

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft will be removed from its protective covering. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1087

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians begin to remove the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1088

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1084

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft will be removed from its protective covering. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1379

NASA Image and Video Library

2011-02-05

VANDENBERG AIR FORCE BASE, Calif. -- At Vandenberg Air Force Base in California, technicians are preparing to join NASA's Glory spacecraft with the Taurus XL rocket's third stage housed inside a temporary processing tent near the pad at Space Launch Complex 576-E. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Randy Beaudoin, VAFB

KSC-2011-1089

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1086

NASA Image and Video Library

2011-01-13

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, a technician begins to remove the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

Development of a double beam process for joining aluminum and steel

NASA Astrophysics Data System (ADS)

Frank, Sascha

2014-02-01

Multi-material structures pose an attractive option for overcoming some of the central challenges in lightweight design. An exceptionally high potential for creating cost-effective lightweight solutions is attributed to the combination of steel and aluminum. However, these materials are also particularly difficult to join due to their tendency to form intermetallic compounds (IMCs). The growth of these compounds is facilitated by high temperatures and long process times. Due to their high brittleness, IMCs can severely weaken a joint. Thus, it is only possible to create durable steel-aluminum joints when the formation of IMCs can be limited to a non-critical level. To meet this goal, a new joining method has been designed. The method is based on the combination of a continuous wave (pw) and a pulsed laser (pw) source. Laser beams from both sources are superimposed in a common process zone. This makes it possible to apply the advantages of laser brazing to mixed-metal joints without requiring the use of chemical fluxes. The double beam technology was first tested in bead-on-plate experiments using different filler wire materials. Based on the results of these tests, a process for joining steel and aluminum in a double-flanged configuration is now being developed. The double flanged seams are joined using zinc- or aluminum-based filler wires. Microsections of selected seams show that it is possible to achieve good base material wetting while limiting the growth of IMCs to acceptable measures. In addition, the results of tensile tests show that high joint strengths can be achieved.

Blind Ambition

ERIC Educational Resources Information Center

Olson, Catherine Applefeld

2009-01-01

No matter how dedicated they may be, some teachers are daunted by extreme challenges. Carol Agler, music director at the Ohio State School for the Blind (OSSB), is not one of those teachers. Since joining the OSSB staff 11 years ago, Agler has revived the school's long-dormant band program and created its first marching band. Next January, she…

Patient Care Coordinator | Center for Cancer Research

Cancer.gov

We are looking for a Patient Care Coordinator to join our clinical team to help us coordinate care for patients enrolled on our clinical research protocols. Duties include scheduling appointments, coordinating new patients, obtaining patient records, attending weekly clinic meetings, and data base entry. Be part of our mission to solve the most important, challenging and

Growing Leaders in Emergent Markets: Leadership Enhancement in the New South Africa

ERIC Educational Resources Information Center

April, Kurt A.; April, Amanda R.

2007-01-01

South Africa has unique challenges. Thirteen years since becoming democratic, it is still going through its own unprecedented change in joining the global economic network and moving from Apartheid to democracy and from a closed to an open community. These political and sociological changes have also infiltrated business and therefore management…

New York City's Small Public Schools: Opportunities for Achievement.

ERIC Educational Resources Information Center

Brownell, Carol, Ed.; Libby, Joan

In 1994, four New York City school reform organizations joined to form the New York Networks for School Renewal (NYNSR) and received the first Annenberg Challenge urban grant. NYNSR goals are to expand the number of small, excellent public schools in New York City neighborhoods, particularly those with few educational options; encourage the spread…

Ahead of the Curve: State Success in the Developmental Education Initiative

ERIC Educational Resources Information Center

Altstadt, David

2012-01-01

Building on their work through Achieving the Dream, six states and 15 community colleges joined the Developmental Education Initiative (DEI) in 2009 to take on one of higher education's most daunting challenges: improving the success of students who enter community college academically underprepared. The states and Jobs for the Future, which…

Acting Out! Combating Homophobia through Teacher Activism. Practitioner Inquiry Series

ERIC Educational Resources Information Center

Blackburn, Mollie V., Ed.; Clark, Caroline T., Ed.; Kenney, Lauren M., Ed.; Smith, Jill M., Ed.

2009-01-01

In this volume, teachers from urban, suburban, and rural districts join together in a teacher inquiry group to challenge homophobia and heterosexism in schools and classrooms. To create safe learning environments for all students they address key topics, including seizing teachable moments, organizing faculty, deciding whether to come out in the…

Beautiful Nonsense: Children's Authentic Art-Making and Deleuzian Difference

ERIC Educational Resources Information Center

Grube, Vicky

2014-01-01

When we join with another who shares our sensibilities, we have potential for doing good. This article explores how the self-initiated art making of children that happens outside the classroom challenges the child emotionally and intellectually more than teacher-directed school art. Furthermore, authentic collaborative art making creates a site…

Crying Foul: Scholars Examine the Consequences of Sports Marketing

ERIC Educational Resources Information Center

Roach, Ronald

2005-01-01

In recent years, scholars have increasingly joined with activists to challenge marketing aimed at children. It is a widely accepted belief that marketers have sold unhealthy foods as well as questionable toys and games, to the detriment of American children. Motivated by declining measures of child well-being, such as heightened obesity rates,…

Evolving psychosocial, emotional, functional, and support needs of women with advanced breast cancer: Results from the Count Us, Know Us, Join Us and Here & Now surveys.

PubMed

Cardoso, Fatima; Harbeck, Nadia; Mertz, Shirley; Fenech, Doris

2016-08-01

Although medical advances have marginally improved survival of women with advanced breast cancer, their psychosocial, emotional, and functional needs remain unmet. Two surveys, Count Us, Know Us, Join Us (Count Us) and Here & Now (H&N), were conducted to understand the unique challenges faced by women with advanced breast cancer and to identify ways of addressing these issues. A total of 1577 women with advanced breast cancer (Count Us, N = 1273; H&N, N = 304) participated in the two surveys, which revealed several previously unreported challenges. Nearly half the women felt isolated and worried, and slightly more than half experienced declines in income because of change in employment; 41% of women felt that support from family and friends decreased over time, and many patients believed information about advanced breast cancer was inadequate and difficult to find. Concerted efforts by people who care for and support women with advanced breast cancer are urgently needed to address these issues. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sustaining The Quality Of The All Volunteer Force: A Cost Effective Approach

DTIC Science & Technology

2016-05-26

new norm, youth unemployment, veteran family members, sex , age, and race. Generally, propensity in the US is higher for men than women, decreases with...troubled inner cities. He envisioned inner city kids from broken homes, finding stability, a taste of...towards kids joining their local Army JROTC programs to learn more about the Army on channels where airtime is much less expensive. This would replace an

Battle Staff Training and Synchronization in Light Infantry Battalions and Task Forces

DTIC Science & Technology

1991-12-01

Institute for the Behavioral and Social Sciences Fort Benning Field Unit (ARI-Benning) joined the Training Research Laboratory’s Determinants of Effective ...and unforgiving. The effective management and manipulation of stressors in a continuous operations environment, along with an efficient and consistent...an organizational effectiveness model grounded in the General Systems Theory model. An extensive body of work was reviewed, but two authors stand out

Social Movements And Social Media: Surveillance And Unintended Consequences

DTIC Science & Technology

2017-12-01

of contentious politics: “ when ordinary people , often in league with more influential citizens, join forces in confrontations with elites...determination of that context.13 When change occurs in a society , the location, interests, and diminished relevance of existing interests facilitate the...distinguish it from previous forms of contention.21 Tarrow argues that “ when contention spreads across an entire society , as it sometimes does, we see a

NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth

Science.gov Websites

and in Space | News | NREL NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth and in Space NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth and in Space . NREL joined forces with NASA in finding new, more precise ways to trigger internal short circuits

Touchstones for the Military Leadership Engaged in Asymmetric Warfare

DTIC Science & Technology

2004-03-19

stricken conditions, to compensation for low esteem status, to religion and/or ideology driven needs to lastly, the vendetta driven need, wherein...Only about one fifth of the total interrogated had genuine religious fervor as the driving force and the ones with low esteem status and vendetta...FIGURE 1 REASONS FOR JOINING MILITANCY Some other findings revealed that for the low esteem category, the perceived luster of a ‘Robin

Water Survival Training - Astronauts - JSC

NASA Image and Video Library

1978-01-01

S78-33616 (31 July-2 Aug 1978) --- Taking a break from the various training exercises at a three-day water survival school held near Homestead Air Force Base, Florida are these five astronaut candidates left to right are Sally K. Ride, Judith A. Resnik, Anne L. Fisher; Kathryn D. Sullivan and Rhea Seddon. They were among fifteen mission specialist-astronaut candidates who joined one of the pilot astronaut candidates for the training.

Navy Recruitment Potential in Junior Colleges

DTIC Science & Technology

1975-07-01

predominantly young (18-21 years old). high school graduates, from middle to upper-income families. They tended to be quite bright. Most are enrolled in college...attitude surveys. The rate for joining the enlisted force is particularly favorable for youth beyond high school , How- ever, very few of the junior college...83 1. Immediate Post- School Plans...................... 85 •1 2. Overall Attitude Toward Military Service . 89 3. The Active

European Summit on the Prevention and Self-Management of Chronic Respiratory Diseases: report of the European Union Parliament Summit (29 March 2017).

PubMed

Hellings, Peter W; Borrelli, David; Pietikainen, Sirpa; Agache, Ioana; Akdis, Cezmi; Bachert, Claus; Bewick, Michael; Botjes, Erna; Constantinidis, Jannis; Fokkens, Wytske; Haahtela, Tari; Hopkins, Claire; Illario, Maddalena; Joos, Guy; Lund, Valerie; Muraro, Antonella; Pugin, Benoit; Seys, Sven; Somekh, David; Stjärne, Pär; Valiulis, Arunas; Valovirta, Erkka; Bousquet, Jean

2017-01-01

On March 29, 2017, a European Summit on the Prevention and Self-Management of Chronic Respiratory Diseases (CRD) was organized by the European Forum for Research and Education in Allergy and Airway Diseases. The event took place in the European Parliament of Brussels and was hosted by MEP David Borrelli and MEP Sirpa Pietikainen. The aim of the Summit was to correspond to the needs of the European Commission and of patients suffering from CRD to join forces in Europe for the prevention and self-management. Delegates of the European Rhinologic Society, European Respiratory Society, European Academy of Allergy and Clinical Immunology, European Academy of Paediatrics, and European Patients Organization EFA all lectured on their vision and action plan to join forces in achieving adequate prevention and self-management of CRD in the context of Precision Medicine. Recent data highlight the preventive capacity of education on optimal care pathways for CRD. Self-management and patient empowerment can be achieved by novel educational on-line materials and by novel mobile health tools enabling patients and doctors to monitor and optimally treat CRDs based on the level of control. This report summarizes the contributions of the representatives of different European academic stakeholders in the field of CRD.

Linear friction weld process monitoring of fixture cassette deformations using empirical mode decomposition

NASA Astrophysics Data System (ADS)

Bakker, O. J.; Gibson, C.; Wilson, P.; Lohse, N.; Popov, A. A.

2015-10-01

Due to its inherent advantages, linear friction welding is a solid-state joining process of increasing importance to the aerospace, automotive, medical and power generation equipment industries. Tangential oscillations and forge stroke during the burn-off phase of the joining process introduce essential dynamic forces, which can also be detrimental to the welding process. Since burn-off is a critical phase in the manufacturing stage, process monitoring is fundamental for quality and stability control purposes. This study aims to improve workholding stability through the analysis of fixture cassette deformations. Methods and procedures for process monitoring are developed and implemented in a fail-or-pass assessment system for fixture cassette deformations during the burn-off phase. Additionally, the de-noised signals are compared to results from previous production runs. The observed deformations as a consequence of the forces acting on the fixture cassette are measured directly during the welding process. Data on the linear friction-welding machine are acquired and de-noised using empirical mode decomposition, before the burn-off phase is extracted. This approach enables a direct, objective comparison of the signal features with trends from previous successful welds. The capacity of the whole process monitoring system is validated and demonstrated through the analysis of a large number of signals obtained from welding experiments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

The EV Everywhere Workplace Charging Challenge aims to have 500 U.S. employers offering workplace charging by 2018. These reports describe the progress made in the Challenge. In 2015, the Workplace Charging Challenge celebrated a major milestone – it reached the halfway point to its goal of 500 Challenge partners committed to installing workplace charging by 2018. More than 250 employers have joined as Challenge partners and the installation of workplace charging as a sustainable business practice is growing across the country. Their efforts have resulted in more than 600 workplaces with over 5,500 charging stations accessible to nearly one millionmore » employees. In 2015, more than 9,000 PEV-driving employees charged at these worksites on a regular basis. Our Workplace Charging Challenge Mid-Program Review reports this progress and other statistics related to workplace charging, including employee satisfaction and charger usage.« less

Advancing Climate Change Education and Youth Empowerment: Preparing Our Communities with the Skills, Knowledge, and Passion to Push for and Develop Innovative Solutions

NASA Astrophysics Data System (ADS)

Niepold, F., III; Johnston, E.; Rooney-varga, J. N.; Qusba, L.; Staveloz, W.; Poppleton, K.; Cloyd, E. T.; Kretser, J.; Bozuwa, J.; Edkins, M. T.

2016-12-01

Today's youth are the first generation to come of age amid rapid climate change, and they have the most at stake in how society responds to it. Climate change will bring economic and environmental challenges as well as opportunities, and citizens who understand the issues at stake will be better prepared to respond. Climate education is a necessary foundation for them to understand and help tackle the complex issue of climate change. Many will become leaders with the skills, knowledge, and passion to push for and develop innovative solutions. As such, this topic requires interdisciplinary and transdisciplinary approaches from a professionally diverse group of experts to effectively build the solid foundation for a low carbon and sustainable economy. Educators from all disciplines need to be enlisted to contribute their talents in building students knowledge and skills to limit human-induced climate change while being prepared for the projected impacts that will continue, and it will accelerate significantly if global emissions of heat-trapping gases continue to increase. This presentation will discuss the new youth and educator engagement partnerships that developed to achieve ways of addressing the problems and opportunities resulting from climate change. We will describe how the partnerships are helping lift up and raise the profile of effective programs that enable transdisciplinary solutions to societal issues. The #Youth4Climate and #Teach4Climate social media campaigns were organized by a flotilla of federal and non-federal partners to inspire young people around the world to take actions on climate change and inspire teachers to prepare students to be part of the solutions to climate change. The largest one, the #Youth4Climate campaign for COP21 youth engagement had over 33 million impressions and opened a discussion for all to join with youth for climate actions at COP21. Each of these three social media campaigns had a simple ask, give young people a voice and prepare them to succeed in doing something about climate change. We are excited to have new partners join forces and support young people, giving them a voice and an opportunity to lead in Paris and beyond. We know the solutions are here, and are committed to working together to build a climate-friendly world. Join us with #Youth4Climate and #Teach4Climate.

Stepping flexures

NASA Technical Reports Server (NTRS)

Vranish, John M. (Inventor)

2009-01-01

An actuator for moving a load has a frame forming a race between two surfaces thereof, at least two elements joined together by at least one flexible member, the elements and the at least one flexible member being disposed between the two surfaces of the frame that forms a race, one of the elements further joined to the load by a portion of the at least one flexible member, wherein when an element comes into contact with a surface of the frame it will stick thereto absent a repelling force, and moving means disposed to selectively attract or repel a corresponding element towards or away from one or the other of the two surfaces of the frame that forms the race. The actuator effects movement of the load in a direction towards or away from the elements, by changing a position of at least one of the elements on a surface of the frame that forms the race.

Low-Stroke Actuation for a Serial Robot

NASA Technical Reports Server (NTRS)

Ihrke, Chris A. (Inventor); Gao, Dalong (Inventor)

2014-01-01

A serial robot includes a base, first and second segments, a proximal joint joining the base to the first segment, and a distal joint. The distal joint that joins the segments is serially arranged and distal with respect to the proximal joint. The robot includes first and second actuators. A first tendon extends from the first actuator to the proximal joint and is selectively moveable via the first actuator. A second tendon extends from the second actuator to the distal joint and is selectively moveable via the second actuator. The robot includes a transmission having at least one gear element which assists rotation of the distal joint when an input force is applied to the proximal and/or distal joints by the first and/or second actuators. A robotic hand having the above robot is also disclosed, as is a robotic system having a torso, arm, and the above-described hand.

Challenges and opportunities in international molecular cancer prevention research: An ASPO Molecular Epidemiology and the Environment and International Cancer Prevention Interest Groups Report.

PubMed

Epplein, Meira; Bostick, Roberd M; Mu, Lina; Ogino, Shuji; Braithwaite, Dejana; Kanetsky, Peter A

2014-11-01

The International Agency for Research on Cancer estimates that over half of the new cancer cases and almost two-thirds of the cancer deaths in 2012 occurred in low and middle income countries. To discuss the challenges and opportunities to reducing the burden of cancer worldwide, the Molecular Epidemiology and the Environment and the International Issues in Cancer Special Interest Groups joined forces to hold a session during the 38th Annual Meeting of the American Society of Preventive Oncology (March 2014, Arlington, Virginia). The session highlighted three topics of particular interest to molecular cancer prevention researchers working internationally, specifically: 1) biomarkers in cancer research; 2) environmental exposures and cancer; and 3) molecular pathological epidemiology. A major factor for successful collaboration illuminated during the discussion was the need for strong, committed, and reliable international partners. A key element of establishing such relationships is to thoroughly involve individual international collaborators in the development of the research question; engaged international collaborators are particularly motivated to champion and shepherd the project through all necessary steps, including issues relating to institutional review boards, political sensitivity, laboratory-based assays, and tumor subtyping. Also essential is allotting time for the building, maintaining, and investing in such relationships so that successful international collaborations may take root and bloom. While there are many challenges inherent to international molecular cancer research, the opportunities for furthering the science and prevention of cancer worldwide are great, particularly at this time of increasing cancer incidence and prevalence in low and middle income countries. ©2014 American Association for Cancer Research.

Diffusion bonding

DOEpatents

Anderson, Robert C.

1976-06-22

1. A method for joining beryllium to beryllium by diffusion bonding, comprising the steps of coating at least one surface portion of at least two beryllium pieces with nickel, positioning a coated surface portion in a contiguous relationship with an other surface portion, subjecting the contiguously disposed surface portions to an environment having an atmosphere at a pressure lower than ambient pressure, applying a force upon the beryllium pieces for causing the contiguous surface portions to abut against each other, heating the contiguous surface portions to a maximum temperature less than the melting temperature of the beryllium, substantially uniformly decreasing the applied force while increasing the temperature after attaining a temperature substantially above room temperature, and maintaining a portion of the applied force at a temperature corresponding to about maximum temperature for a duration sufficient to effect the diffusion bond between the contiguous surface portions.

Understanding the diversity of public interests in wildlife conservation.

PubMed

Teel, Tara L; Manfredo, Michael J

2010-02-01

North American state wildlife agencies are increasingly faced with the challenge of effectively representing a diverse public. With increasing social conflict over wildlife issues, the future of wildlife conservation hinges on preparedness of the profession to respond to this challenge. In the interest of finding ways to improve response, 19 agencies in the western U.S. joined forces to initiate an investigation that would provide a better understanding of the diversity of wildlife-related interests in the region. Specific objectives, accomplished through use of a mail survey administered in 2004, were to categorize people on the basis of their value orientations toward wildlife and explore how different groups were distributed across states and to examine differences on sociodemographic characteristics and attitudes toward wildlife-related topics among groups. The focus was on two orientations: domination (view of wildlife that prioritizes human well-being over wildlife and treats wildlife in utilitarian terms); and mutualism (view of wildlife as capable of relationships of trust with humans and defined by a desire for companionship with wildlife). Four types of people were identified on the basis of these orientations. Types differed in their geographic distribution and wildlife-related attitudes and behaviors, revealing how value orientations can form the foundation for conflict on wildlife issues. Our characterizations of stakeholder groups offer a framework that can be applied over time and across geographic scales to improve conservation planning efforts and inform broader thinking about the social aspects of wildlife conservation.

Kids at Hope: All Children Are Capable of Success--No Exceptions!

ERIC Educational Resources Information Center

Tipps, Christine R.

2006-01-01

How has our society typically responded to the challenging problems facing youths? Communities have, more often than not, focused resources on prevention programs that have attempted to stop youths from taking drugs, joining gangs, getting pregnant, and dropping out of school, among other things. A problem is identified, and the response is to…

Identifying Obstacles to a Multidisciplinary Understanding of "Disruptive" Behaviour

ERIC Educational Resources Information Center

Macleod, Gale

2010-01-01

This paper examines the possibilities and challenges presented by an interdisciplinary approach to the study of disruptive behaviour. It is argued that whilst such an approach is to be welcomed, work needs to be done in order to ensure that educational research joins the discussion as an equal partner. The paper begins with a demonstration of how…

Professional Identity and Engagement among Newly Qualified Teachers in Times of Uncertainty

ERIC Educational Resources Information Center

Correa Gorospe, José Miguel; Martínez-Arbelaiz, Asunción; Fernández-Olaskoaga, Lorea

2018-01-01

Social, political and economic conditions shape a context of permanent flux where early childhood education teachers have to join the labour market and build their professional identity while facing numerous challenges. The aim of this study is to investigate the effects that a changing world and precarious job conditions can have on newly…

Corrupting Conversations with the Marquis de Sade: On Education, Gender, and Sexuality

ERIC Educational Resources Information Center

Greteman, Adam J.

2016-01-01

In this essay, the author joins a conversation started by Martin ("Reclaiming the conversation: the ideal of the educated woman." Yale University Press, New Haven, 1985) regarding gender and education seeking to extend the conversation to address sexuality. To do so, the author brings a reading of the Marquis de Sade to challenge the…

Air Force Research Laboratory’s Focused Long Term Challenges

DTIC Science & Technology

2008-04-01

Air Force Research Laboratory ( AFRL ) mission is to provide support to the Air Force (AF) and the warfighters with... Air Force Research Laboratory’s Focused Long Term Challenges Leo J Rose Munitions Directorate, Air Force Research Laboratory , 101 W Eglin Blvd...This technology vision, which was born in our Air Force Research Laboratory , builds on the Air Force’s traditional kill

KSC-2010-1274

NASA Image and Video Library

2010-01-15

CAPE CANAVERAL, Fla. - A trio of green sea turtles rest in a box at Cape Canaveral Air Force Station in Florida after the animals were outfitted with tracking transmitters. The turtles were some of nearly 2,000 that were "stunned" by the recent drop in temperatures. Many of the turtles were rescued from the Mosquito Lagoon, with others coming from the Indian River Lagoon and Cocoa Beach. Biologists, environmentalists, wildlife experts and other volunteers joined forces with a massive rescue effort at the Merritt Island National Wildlife Refuge, where the turtles were identified, examined and transported to rehabilitation facilities throughout Florida and South Georgia. The animals stayed at these facilities until local waters warmed up to safe temperatures. Photo credit: NASA/Jack Pfaller

KSC-2010-1272

NASA Image and Video Library

2010-01-15

CAPE CANAVERAL, Fla. - A tracking transmitter is installed on the shell of an endangered green sea turtle at Cape Canaveral Air Force Station in Florida. A recent cold snap left this turtle and nearly 2,000 others "stunned" and in need of help. Many of the turtles were rescued from the Mosquito Lagoon, with others coming from the Indian River Lagoon and Cocoa Beach. Biologists, environmentalists, wildlife experts and other volunteers joined forces with a massive rescue effort at the Merritt Island National Wildlife Refuge, where the turtles were identified, examined and transported to rehabilitation facilities throughout Florida and South Georgia. The animals stayed at these facilities until local waters warmed up to safe temperatures. Photo credit: NASA/Jack Pfaller

KSC-2010-1276

NASA Image and Video Library

2010-01-15

CAPE CANAVERAL, Fla. - An endangered green sea turtle awaits release as its shell is tagged with a tracking transmitter at Cape Canaveral Air Force Station in Florida. A recent cold snap left this turtle and nearly 2,000 others "stunned" and in need of help. Many of the turtles were rescued from the Mosquito Lagoon, with others coming from the Indian River Lagoon and Cocoa Beach. Biologists, environmentalists, wildlife experts and other volunteers joined forces with a massive rescue effort at the Merritt Island National Wildlife Refuge, where the turtles were identified, examined and transported to rehabilitation facilities throughout Florida and South Georgia. The animals stayed at these facilities until local waters warmed up to safe temperatures. Photo credit: NASA/Jack Pfaller

KSC-2010-1275

NASA Image and Video Library

2010-01-15

CAPE CANAVERAL, Fla. - An endangered green sea turtle is outfitted with a tracking transmitter at Cape Canaveral Air Force Station in Florida. A recent cold snap left this turtle and nearly 2,000 others "stunned" and in need of help. Many of the turtles were rescued from the Mosquito Lagoon, with others coming from the Indian River Lagoon and Cocoa Beach. Biologists, environmentalists, wildlife experts and other volunteers joined forces with a massive rescue effort at the Merritt Island National Wildlife Refuge, where the turtles were identified, examined and transported to rehabilitation facilities throughout Florida and South Georgia. The animals stayed at these facilities until local waters warmed up to safe temperatures. Photo credit: NASA/Jack Pfaller

A microdynamic version of the tensile test machine

NASA Technical Reports Server (NTRS)

Glaser, R. J.

1991-01-01

Very large space structures require structural reactions to control forces associated with nanometer-level displacements; JPL has accordingly built a tensile test machine capable of mN-level force measurements and nm-level displacement measurements, with a view to the study of structural linear joining technology at the lower limit of its resolution. The tester is composed of a moving table that is supported by six flexured legs and a test specimen cantilevered off the table to ground. Three vertical legs contain piezoactuators allowing changes in length up to 200 microns while generating axial load and bending moments. Displacements between ground and table are measured by means of three laser-interferometric channels.

Foot pedal operated fluid type exercising device

NASA Technical Reports Server (NTRS)

Crum, G. W.; Sauter, R. J. (Inventor)

1973-01-01

A foot pedal operated exercising device is reported that contains a dynamometer formed of a pair of cylinders each containing a piston. The pistons are linked to each other. The upper portions of the two cylinders are joined together by a common opening to provide a common fluid reservoir and each piston is provided with a one way check valve to maintain an adequate supply of working fluid. Fluid from the driven cylinder is transmitted to the other cylinder through separate constant force spring biased valves each valve takes the predominant portion of the pressure drop thereby providing a constant force hydraulic dynamometer. A device is provided to determine the amount of movement of piston travel.

KSC-2011-1179

NASA Image and Video Library

2011-01-20

VANDENBERG AIR FORCE BASE, Calif. -- The solar arrays of NASA's Glory spacecraft are illuminated in the Astrotech payload processing facility at Vandenberg Air Force Base in California. The spacecraft will be processed for flight, encapsulated in its protective payload fairing, and then transported to Space Launch Complex 576-E where is will be joined with the third stage of the Orbital Sciences Corp. Taurus XL rocket. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Randy Beaudoin, VAFB

KSC-2011-1177

NASA Image and Video Library

2011-01-20

VANDENBERG AIR FORCE BASE, Calif. -- The solar arrays of NASA's Glory spacecraft are illuminated in the Astrotech payload processing facility at Vandenberg Air Force Base in California. The spacecraft will be processed for flight, encapsulated in its protective payload fairing, and then transported to Space Launch Complex 576-E where is will be joined with the third stage of the Orbital Sciences Corp. Taurus XL rocket. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Randy Beaudoin, VAFB

Nuclear Energy in Southeast Asia: Pull Rods or Scram

DTIC Science & Technology

2009-06-01

December 29, 2008);  Seth Mydans, “Tens of thousands join Myanmar protest,” International Harold Tribune, September 24, 2007, http://www.iht.com...articles/2007/09/24/news/myanmar.php (accessed December 29, 2008); Seth Mydans; “Myanmar monk protest contained by Junta forces,” The New York Times...Nuclear Plant for Electricity.” Associated Press, September 26, 2008. http://www.ap.org (accessed October 20, 2008). Mydans, Seth . “Myanmar monk

An Experimental Investigation Into the Feasibility of Measuring Static and Dynamic Aerodynamic Derivatives in the DSTO Water Tunnel

DTIC Science & Technology

2013-08-01

The SDM was subjected to forced small (0.5) sinusoidal pitching oscillations and derivatives were computed from measured model loads, angles of... aluminium alloy when subjected to both tensile and torsional loading. He joined the Aeronautical Research Laboratories (now called the Defence...oscillations and derivatives were computed from measured model loads, angles of attack, reduced frequency of oscillation and aircraft geometrical parameters

Toward computational crime prediction. Comment on "Statistical physics of crime: A review" by M.R. D'Orsogna and M. Perc

NASA Astrophysics Data System (ADS)

Ferrara, Emilio

2015-03-01

Containing the spreading of crime in modern society in an ongoing battle: our understanding of the dynamics underlying criminal events and the motifs behind individuals therein involved is crucial to design cost-effective prevention policies and intervention strategies. During recent years we witnessed various research fields joining forces, sharing models and methods, toward modeling and quantitatively characterizing crime and criminal behavior.

The Dual Function of the Indonesian Armed Forces (Dwi Fungsi ABRI)

DTIC Science & Technology

1993-12-01

miles) from north to south. Indonesia’s 13,667 islands are nestled between two continents, Asia and Australia, and two oceans, the Indian and the...shares borders with Malaysia , Papua New Guinea and sea borders with Singapore, Thailand, Vietnam, the Philippines, and 9 Australia. Indonesia’s Exclusive...Asian Nation (ASEAN), which it co-founded in 1967 along with Thailand, the Philippines, Malaysia and Singapore. Brunei joined in 1984. Indonesia was

Microstructure Engineering in Hot Strip Mills, Part 1 of 2: Integrated mathematical Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.K. Brimacombe; I.V. Samaraseker; E.B. Hawbolt

1998-09-30

This report describes the work of developing an integrated model used to predict the thermal history, deformation, roll forces, microstructural evaluation and mechanical properties of steel strip in a hot-strip mill. This achievement results from a join research effort that is part of the American Iron and Steel Institute's (AISI) Advanced Process Control Program, a collaboration between the U.S. DOE and fifteen North American steel makers.

Rapid Deployment Logistics: Lebanon, 1958

DTIC Science & Technology

1984-10-01

planning. In case of a general conflict, the 1st Infantry Division and 82d Airborne Division would also join STRAC. 7 Wet ...was aware of the problem and had long been researching different methods of cargo handling. Roll-on and roll-off ships provided one solution. In 1954...battalion land.ng team, or b, combining both methods . Basically, the forces were to deter 3- stop hostilities between Israel and Arab E’tates, r2

The United States Air Force in Southeast Asia, 1961-1973

DTIC Science & Technology

1977-01-01

for worry was the substantial of Saigon. The French subsequently political support the Communist par- began negotiations with the Chinese ties of...those of Indochina, in Chinese Army of its responsibilities the postwarperiod. under General Order No. 1. The During the last months of the war, French...commander, Gen. Jacques U.S. agents had been parachuted into Leclerc, began negotiations with Ho the hills of Annam where they joined and, on 6 March

JPRS Report, East Europe.

DTIC Science & Technology

1990-06-04

Although even today the 1945 minorities law have joined. which is still in force would do the job .... [Szucs] In a manner similar to the Germans...than by any utopias. manual jobs , but upon the intervention of the State Security Corps he got dismissed from every one of However, I appeal also to...in the private sector; small enterprises affirmative to the question of whether as a woman she offer double or triple the amount they earned at the

Study of two different thin film coating methods in transmission laser micro-joining of thin Ti-film coated glass and polyimide for biomedical applications.

PubMed

Sultana, T; Georgiev, G L; Baird, R J; Auner, G W; Newaz, G; Patwa, R; Herfurth, H J

2009-07-01

Biomedical devices and implants require precision joining for hermetic sealing which can be achieved with low power lasers. The effect of two different thin metal film coating methods was studied in transmission laser micro-joints of titanium-coated glass and polyimide. The coating methods were cathodic arc physical vapor deposition (CA-PVD) and electron beam evaporation (EB-PVD). Titanium-coated glass joined to polyimide film can have neural electrode application. The improvement of the joint quality will be essential for robust performance of the device. Low power fiber laser (wave length = 1100 nm) was used for transmission laser micro-joining of thin titanium (Ti) film (approximately 200 nm) coated Pyrex borosilicate 7740 glass wafer (0.5 mm thick) and polyimide (Imidex) film (0.2 mm thick). Ti film acts as the coupling agent in the joining process. The Ti film deposition rate in the CA-PVD was 5-10 A/s and in the EB-PVD 1.5 A/s. The laser joint strength was measured by a lap shear test, the Ti film surfaces were analyzed by atomic force microscopy (AFM) and the lap shear tested joints were analyzed by optical microscopy and scanning electron microscopy (SEM). The film properties and the failure modes of the joints were correlated to joint strength. The CA-PVD produced around 4 times stronger laser joints than EB-PVD. The adhesion of the Ti film on glass by CA-PVD is better than that of the EB-PVD method. This is likely to be due to a higher film deposition rate and consequently higher adhesion or sticking coefficient for the CA-PVD particles arriving on the substrate compared to that of the EB-PVD film. EB-PVD shows poor laser bonding properties due to the development of thermal hotspots which occurs from film decohesion.

Multidisciplinary workshops: learning to work together.

PubMed

Fatchett, Anita; Taylor, Dawn

2013-03-01

Health and social care professional practice needs to move with the times and to respond to the ever-changing combination of health needs, economic realities and health-policy imperatives. A clear understanding of the variety of forces at play and the ability to marshal these to good effect by working in partnership with multidisciplinary colleagues and children/families is a must, not least in this time of economic austerity and ever-rising health inequalities, when vulnerable children's lives and complex family relationships and behaviours so easily become increasingly strained and challenged. This sad reality calls out for relevant joined-up solutions by all participants--an agenda so often called into question by court judgement after court judgement. The multidisciplinary workshops to be discussed have developed and changed over the past decade and provide a safe but realistic learning environment for students from health and social care backgrounds to experience the difficulties and barriers to good multidisciplinary working, to better understand others' perspectives and activities and consider and develop new and better practical strategies for working with multidisciplinary professional colleagues, children and families. All of the workshops are underpinned by specific discipline-focused theoretical work.

Forensic Metrology: Its Importance and Evolution in the United States

NASA Astrophysics Data System (ADS)

Vosk, JD Ted

2016-11-01

Forensic measurements play a significant role in the U.S. criminal justice system. Guilt or innocence, or the severity of a sentence, may depend upon the results of such measurements. Until recently, however, forensic disciplines were largely unaware of the field of metrology. Accordingly, proper measurement practices were often, and widely, neglected. These include failure to adopt proper calibration techniques, establish the traceability of results and determine measurement uncertainty. These failures undermine confidence in verdicts based upon forensic measurements. Over the past decade, though, the forensic sciences have been introduced to metrology and its principles leading to more reliable measurement practices. The impetus for this change was driven by many forces. Pressure came initially from criminal defense lawyers challenging metrologically unsound practices and results relied upon by government prosecutions. Litigation in the State of Washington led this movement spurring action by attorneys in other jurisdictions and eventually reform in the measurement practices of forensic labs around the country. Since then, the greater scientific community, other forensic scientists and even prosecutors have joined the fight. This paper describes the fight to improve the quality of justice by the application of metrological principles and the evolution of the field of forensic metrology.

New Targets for New Accelerators

NASA Astrophysics Data System (ADS)

Frentz, Bryce; Manukyan, Khachatur; Aprahamian, Ani

2013-10-01

New accelerators, such as the 5 MV Sta Ana accelerator at the University of Notre Dame, will produce more powerful beams up to 100's of μAmps. These accelerators require a complete rethinking of target preparation since the high intensity of such beams would melt conventional targets. Traditionally, accelerator targets are made with a tantalum backing because of its high atomic mass. However, tantalum is brittle, a poor conductor, and, if produced commercially, often contains impurities (e.g. fluorine) that produce undesirable background and reaction products. Tungsten, despite its brittle structure and poor conductivity, has a high atomic mass and lacks impurities, making it a more desirable backing. In conjunction with tungsten's properties, copper is robust and a far superior thermal conductor. We describe a new method of reactive joining that we developed for creating targets that use the advantageous properties of both tungsten and copper. This process involved placing a reactive mixture between tungsten and copper and applying a load force. The mixture is then ignited, and while under pressure, the system produces conditions to join the materials. We present our investigation to optimize the process of reactive joining, as well as some of the final target's properties. This work was supported by the National Science Foundation under Grant PHY-1068192.

Phoretic forces on convex particles from kinetic theory and nonequilibrium thermodynamics

NASA Astrophysics Data System (ADS)

Hütter, Markus; Kröger, Martin

2006-01-01

In this article we derive the phoretic forces acting on a tracer particle, which is assumed to be small compared to the mean free path of the surrounding nonequilibrium gas, but large compared to the size of the surrounding gas molecules. First, we review and extend the calculations of Waldmann [Z. Naturforsch. A 14A, 589 (1959)] using half-sphere integrations and an accommodation coefficient characterizing the collision process. The presented methodology is applied to a gas subject to temperature, pressure, and velocity gradients. Corresponding thermophoretic, barophoretic, and rheophoretic forces are derived, and explicit expressions for spherical particles are compared to known results. Second, nonequilibrium thermodynamics is used to join the diffusion equation for the tracer particle with the continuum equations of nonisothermal hydrodynamics of the solvent. So doing, the distinct origin of the thermophoretic and barophoretic forces is demonstrated. While the latter enters similarly to an interaction potential, the former is given by flux-flux correlations in terms of a Green-Kubo relation, as shown in detail.

Aerodynamics of cyclist posture, bicycle and helmet characteristics in time trial stage.

PubMed

Chabroux, Vincent; Barelle, Caroline; Favier, Daniel

2012-07-01

The present work is focused on the aerodynamic study of different parameters, including both the posture of a cyclist's upper limbs and the saddle position, in time trial (TT) stages. The aerodynamic influence of a TT helmet large visor is also quantified as a function of the helmet inclination. Experiments conducted in a wind tunnel on nine professional cyclists provided drag force and frontal area measurements to determine the drag force coefficient. Data statistical analysis clearly shows that the hands positioning on shifters and the elbows joined together are significantly reducing the cyclist drag force. Concerning the saddle position, the drag force is shown to be significantly increased (about 3%) when the saddle is raised. The usual helmet inclination appears to be the inclination value minimizing the drag force. Moreover, the addition of a large visor on the helmet is shown to provide a drag coefficient reduction as a function of the helmet inclination. Present results indicate that variations in the TT cyclist posture, the saddle position and the helmet visor can produce a significant gain in time (up to 2.2%) during stages.

Families of returned defence force personnel: a changing landscape of challenges.

PubMed

Berle, David; Steel, Zachary

2015-08-01

This paper aims to identify the key challenges experienced by the families of defence force personnel following deployment. We undertook a selective review of four post-deployment challenges to the families of defence force personnel: (1) changes to relationships; (2) changes to family member roles and responsibilities; (3) adjustment of children and parenting challenges; and (4) anger, family conflict and violence. Emerging issues in the area of post-deployment adjustment are also discussed. Empirical studies of post-deployment family adjustment are lacking. Each of the reviewed challenges can contribute to psychological difficulties and precipitate contact with mental health services. The challenges faced by defence force personnel when returning from deployment arise within a family context. Clinicians should thoroughly assess these factors in families following deployment, but also recognise family strengths and resilience to these challenges. © The Royal Australian and New Zealand College of Psychiatrists 2015.

Analysis of human locomotion by recording sole-floor reaction forces from anatomically discrete points.

PubMed

Warabi, Tateo; Kato, Masamichi; Kiriyama, Kiichi; Yoshida, Toshikazu; Kobayashi, Nobuyoshi

2004-12-01

Sole-floor reaction forces were recorded from five anatomically discrete points to analyze characteristics of human locomotion. Strain gauge of 14 mm diameter were firmly attached to the sole of bare-foot for recording force changes from the following five points: (1) medial process of calcaneus, (2) head of 1st metatarsal, (3) head of 3rd metatarsal, (4) head of 5th metatarsal and (5) great toe. Fifteen healthy adults were asked to walk at 2, 4, 6 and 8 km/h and to run at 8 km/h on the treadmill. Sole-floor reaction forces from 1st to 5th metatarsals show reciprocal changes during stance phase, while force from 1st metatarsal is strong 5th metatarsal shows weak reaction and vice versa. This phenomenon may be an expression of locomotor program to maintain vertical stability of the body during stance phase. There was a linear relation between walking speeds and sum of force from the five points, although sum of forces from three metatarsals did not change significantly during the walking speeds, indicating mainly calcaneus and great toe contribute to increasing walking speed. During running the sum of force from the three metatarsals increased sharply, joining the other two points to increase thrust.

More than 200 Dryden staff formed two long lines on the Dryden ramp to greet retired research pilot Gordon Fullerton after his final flight in a NASA F/A-18.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of

NASA Dryden research pilot Gordon Fullerton flies his final mission in NASA F/A-18B #852 in formation with NASA F/A-18A #850 on Dec. 21, 2007.

NASA Image and Video Library

2007-12-21

Long-time NASA Dryden research pilot and former astronaut C. Gordon Fullerton capped an almost 50-year flying career, including more than 38 years with NASA, with a final flight in a NASA F/A-18 on Dec. 21, 2007. Fullerton and Dryden research pilot Jim Smolka flew a 90-minute pilot proficiency formation aerobatics flight with another Dryden F/A-18 and a Dryden T-38 before concluding with two low-level formation flyovers of Dryden before landing. Fullerton was honored with a water-cannon spray arch provided by two fire trucks from the Edwards Air Force Base fire department as he taxied the F/A-18 up to the Dryden ramp, and was then greeted by his wife Marie and several hundred Dryden staff after his final flight. Fullerton began his flying career with the U.S. Air Force in 1958 after earning bachelor's and master's degrees in mechanical engineering from the California Institute of Technology. Initially trained as a fighter pilot, he later transitioned to multi-engine bombers and became a bomber operations test pilot after attending the Air Force Aerospace Research Pilot School at Edwards Air Force Base, Calif. He then was assigned to the flight crew for the planned Air Force Manned Orbital Laboratory in 1966. Upon cancellation of that program, the Air Force assigned Fullerton to NASA's astronaut corps in 1969. He served on the support crews for the Apollo 14, 15, 16 and 17 lunar missions, and was later assigned to one of the two flight crews that piloted the space shuttle prototype Enterprise during the Approach and Landing Test program at Dryden. He then logged some 382 hours in space when he flew on two early space shuttle missions, STS-3 on Columbia in 1982 and STS-51F on Challenger in 1985. He joined the flight crew branch at NASA Dryden after leaving the astronaut corps in 1986. During his 21 years at Dryden, Fullerton was project pilot on a number of high-profile research efforts, including the Propulsion Controlled Aircraft, the high-speed landing tests of sp

Using the Electronic Health Record in Nursing Research: Challenges and Opportunities.

PubMed

Samuels, Joanne G; McGrath, Robert J; Fetzer, Susan J; Mittal, Prashant; Bourgoine, Derek

2015-10-01

Changes in the patient record from the paper to the electronic health record format present challenges and opportunities for the nurse researcher. Current use of data from the electronic health record is in a state of flux. Novel data analytic techniques and massive data sets provide new opportunities for nursing science. Realization of a strong electronic data output future relies on meeting challenges of system use and operability, data presentation, and privacy. Nurse researchers need to rethink aspects of proposal development. Joining ongoing national efforts aimed at creating usable data output is encouraged as a means to affect system design. Working to address challenges and embrace opportunities will help grow the science in a way that answers important patient care questions. © The Author(s) 2015.

Biomimetic-inspired joining of composite with metal structures: A survey of natural joints and application to single lap joints

NASA Astrophysics Data System (ADS)

Avgoulas, Evangelos Ioannis; Sutcliffe, Michael P. F.

2014-03-01

Joining composites with metal parts leads, inevitably, to high stress concentrations because of the material property mismatch. Since joining composite to metal is required in many high performance structures, there is a need to develop a new multifunctional approach to meet this challenge. This paper uses the biomimetics approach to help develop solutions to this problem. Nature has found many ingenious ways of joining dissimilar materials and making robust attachments, alleviating potential stress concentrations. A literature survey of natural joint systems has been carried out, identifying and analysing different natural joint methods from a mechanical perspective. A taxonomy table was developed based on the different methods/functions that nature successfully uses to attach dissimilar tissues (materials). This table is used to understand common themes or approaches used in nature for different joint configurations and functionalities. One of the key characteristics that nature uses to joint dissimilar materials is a transitional zone of stiffness in the insertion site. Several biomimetic-inspired metal-to-composite (steel-to-CFRP), adhesively bonded, Single Lap Joints (SLJs) were numerically investigated using a finite element analysis. The proposed solutions offer a transitional zone of stiffness of one joint part to reduce the material stiffness mismatch at the joint. An optimisation procedure was used to identify the variation in material stiffness which minimises potential failure of the joint. It was found that the proposed biomimetic SLJs reduce the asymmetry of the stress distribution along the adhesive area.

KSC-99pp0833

NASA Image and Video Library

1999-07-16

Commander of the Air Force Space Command, General Richard B. Myers (left) joins Ed Gormel (center) and Commander of the 45th Space Wing Brig. Gen. F. Randall Starbuck (right) after the presentation of the Hammer Award. The Hammer Award is Vice President Al Gore's special recognition of teams of federal employees who have made significant contributions in support of the principles of the National Partnership for Reinventing Government. Morley Winograd, director of the National Partnership for Reinventing Government, presented the award to the Joint Base Operations and Support Contract (J-BOSC) Source Evaluation Board (SEB). Gormel is a co-chair of the SEB. This Hammer Award acknowledges the accomplishments of a joint NASA and Air Force team that established the J-BOSC SEB. The team developed and implemented the acquisition strategy for establishing a single set of base operations and support service requirements for KSC, Cape Canaveral Air Station and Patrick Air Force Base

Wave scheduling - Decentralized scheduling of task forces in multicomputers

NASA Technical Reports Server (NTRS)

Van Tilborg, A. M.; Wittie, L. D.

1984-01-01

Decentralized operating systems that control large multicomputers need techniques to schedule competing parallel programs called task forces. Wave scheduling is a probabilistic technique that uses a hierarchical distributed virtual machine to schedule task forces by recursively subdividing and issuing wavefront-like commands to processing elements capable of executing individual tasks. Wave scheduling is highly resistant to processing element failures because it uses many distributed schedulers that dynamically assign scheduling responsibilities among themselves. The scheduling technique is trivially extensible as more processing elements join the host multicomputer. A simple model of scheduling cost is used by every scheduler node to distribute scheduling activity and minimize wasted processing capacity by using perceived workload to vary decentralized scheduling rules. At low to moderate levels of network activity, wave scheduling is only slightly less efficient than a central scheduler in its ability to direct processing elements to accomplish useful work.

The Hammer Award is presented to KSC and 45th Space Wing.

NASA Technical Reports Server (NTRS)

1999-01-01

Commander of the Air Force Space Command, General Richard B. Myers (left) joins Ed Gormel (center) and Commander of the 45th Space Wing Brig. Gen. F. Randall Starbuck (right) after the presentation of the Hammer Award. The Hammer Award is Vice President Al Gore's special recognition of teams of federal employees who have made significant contributions in support of the principles of the National Partnership for Reinventing Government. Morley Winograd, director of the National Partnership for Reinventing Government, presented the award to the Joint Base Operations and Support Contract (J-BOSC) Source Evaluation Board (SEB). Gormel is a co-chair of the SEB. This Hammer Award acknowledges the accomplishments of a joint NASA and Air Force team that established the J-BOSC SEB. The team developed and implemented the acquisition strategy for establishing a single set of base operations and support service requirements for KSC, Cape Canaveral Air Station and Patrick Air Force Base.

Reflecting on Advice for New Teachers and Educators

ERIC Educational Resources Information Center

Vogel, Linda J.

2007-01-01

Finding mentors who will both support and challenge a teacher to grow is key to that teacher's ability to claim his or her calling as one who teaches and empowers others to join in their faith journeys as life-long learners. The author believes that religious educators must continually hone their skills to read the contexts where they teach as…

The competitive health care marketplace: bringing new challenges to a changing field.

PubMed

Jeppson, D H

1986-07-01

This article, in response to Dr. Weil's article (beginning on page 4), explores the changing health care industry from a different perspective. Stressed here is the need fro hospitals to join an integrated regional network of providers. Also discussed is the responsibility of not-for-profit hospitals to provide indigent care, despite the trend toward prepaid, discounted health plans.

Crafting a New Vision for High School: How States Can Join Academic and Technical Studies to Promote More Powerful Learning

ERIC Educational Resources Information Center

Bottoms, Gene; Young, Marna

2008-01-01

The authors advocate harnessing the applied teaching strategies of career/technical education (CTE) and infusing them into college-preparatory academics to transform secondary schools into high-performing centers of learning where students are both challenged and engaged. By pursuing this strategy, say the authors, states can help many more…

Diversity to the Next Level

ERIC Educational Resources Information Center

Stuart, Reginald

2010-01-01

When Colgate University decided a few years ago to recast its diversity efforts, it joined a small, but growing, number of schools across the U.S. in taking a new approach to a decades-old challenge of how best to make their school more appealing to people from all walks of life and more compelling to employers as a good place to recruit. Colgate,…

Building a Collaboration One Day at a Time: Integrating Infant Mental Health into a Residential Drug Treatment Program

ERIC Educational Resources Information Center

Heffron, Mary Claire; Purcell, Arlene; Schalit, Jackie

2007-01-01

Families In Recovery Staying Together (FIRST) is a team from Children's Hospital and Research Center at Oakland that has joined in collaboration with two local perinatal residential drug treatment programs to create early childhood mental health services at those sites. The authors highlight the collaboration strategies and challenges the partners…

The Closeness of Fit: Towards an Ecomap for the Inclusion of Pupils with ASD in Mainstream Schools

ERIC Educational Resources Information Center

Emam, Mahmoud Mohamed

2014-01-01

The number of pupils with autism spectrum disorder (ASD) who join mainstream schools in the UK has been increasing over the last decade. Given the difficulties in social and emotional understanding which these children have, their inclusion in schools is likely to be challenging. Their ASD-related manifestations, moreover, tend to allow for…

International Systems Integration on the International Space Station

NASA Technical Reports Server (NTRS)

Gerstenmaier, William H.; Ticker, Ronald L.

2007-01-01

Over the next few months, the International Space Station (ISS), and human spaceflight in general, will undergo momentous change. The European Columbus and Japanese Kibo Laboratories will be added to the station joining U.S. and Russian elements already on orbit. Columbus, Jules Vernes Automated Transfer Vehicle (ATV) and Kibo Control Centers will soon be joining control centers in the US and Russia in coordinating ISS operations and research. The Canadian Special Purpose Dexterous Manipulator (SPDM) will be performing extra vehicular activities that previously only astronauts on EVA could do, but remotely and with increased safety. This paper will address the integration of these international elements and operations into the ISS, both from hardware and human perspectives. Interoperability of on-orbit systems and ground control centers and their human operators from Europe, Japan, Canada, Russia and the U.S. pose significant and unique challenges. Coordination of logistical support and transportation of crews and cargo is also a major challenge. As we venture out into the cosmos and inhabit the Moon and other planets, it's the systems and operational experience and partnership development on ISS, humanity's orbiting outpost that is making these journeys possible.

Affordable, Robust Ceramic Joining Technology (ARCJoinT) Given 1999 R and D 100 Award

NASA Technical Reports Server (NTRS)

Singh, Mrityunjay

2000-01-01

Advanced ceramics and fiber-reinforced ceramic matrix composites with high strength and toughness, good thermal conductivity, thermal shock resistance, and oxidation resistance are needed for high-temperature structural applications in advanced high-efficiency and high-performance engines, space propulsion components, and land-based systems. The engineering designs of these systems require the manufacturing of large parts with complex shapes, which are either quite expensive or impossible to fabricate. In many instances, it is more economical to build complex shapes by joining together simple geometrical shapes. Thus, joining has been recognized as an enabling technology for the successful utilization of advanced ceramics and fiber-reinforced composite components in high-temperature applications. However, such joints must retain their structural integrity at high temperatures and must have mechanical strength and environmental stability comparable to those of the bulk materials. In addition, the joining technique should be robust, practical, and reliable. ARCJoinT, which is based on the reaction-forming approach, is unique in terms of producing joints with tailorable microstructures. The formation of joints by this approach is attractive since the thermomechanical properties of the joint interlayer can be tailored to be very close to those of the base materials. In addition, high-temperature fixturing is not needed to hold the parts at the infiltration temperature. The joining process begins with the application of a carbonaceous mixture in the joint area, holding the items to be joined in a fixture, and curing at 110 to 120 C for 10 to 20 min. This step fastens the pieces together. Then, silicon or a silicon alloy in tape, paste, or slurry form is applied around the joint region and heated to 1250 to 1425 C (depending on the type of infiltrant) for 10 to 15 min. The molten silicon or silicon-refractory metal alloy reacts with carbon to form silicon carbide with controllable amounts of silicon and other phases as determined by the alloy composition. Joint thickness can be readily controlled through adjustments of the properties of the carbonaceous paste and the applied fixturing force. The photograph shows various shapes of silicon-carbide-based ceramics and fiberreinforced composites that have been joined using ARCJoinT. Thermomechanical and thermochemical characterization of joints is underway for a wide variety of silicon-carbidebased advanced ceramics and fiber-reinforced composites under the hostile environments that will be encountered in engine applications. ARCJoinT, which was developed by researchers at the NASA Glenn Research Center at Lewis Field, received R&D Magazine's prestigious R&D 100 Award in 1999.

Extended healing validation of an artificial tendon to connect the quadriceps muscle to the Tibia: 180-day study.

PubMed

Melvin, Alan J; Litsky, Alan S; Mayerson, Joel L; Stringer, Keith; Juncosa-Melvin, Natalia

2012-07-01

Whenever a tendon or its bone insertion is disrupted or removed, existing surgical techniques provide a temporary connection or scaffolding to promote healing, but the interface of living to non-living materials soon breaks down under the stress of these applications, if it must bear the load more than acutely. Patients are thus disabled whose prostheses, defect size, or mere anatomy limit the availability or outcomes of such treatments. Our group developed the OrthoCoupler™ device to join skeletal muscle to prosthetic or natural structures without this interface breakdown. In this study, the goat knee extensor mechanism (quadriceps tendon, patella, and patellar tendon) was removed from the right hind limb in 16 goats. The device connected the quadriceps muscle to a stainless steel bone plate on the tibia. Mechanical testing and histology specimens were collected from each operated leg and contralateral unoperated control legs at 180 days. Maximum forces in the operated leg (vs. unoperated) were 1,400 ± 93 N (vs. 1,179 ± 61 N), linear stiffnesses were 33 ± 3 N/mm (vs. 37 ± 4 N/mm), and elongations at failure were 92.1 ± 5.3 mm (vs. 68.4 ± 3.8 mm; mean ± SEM). Higher maximum forces (p = 0.02) and elongations at failure (p=0.008) of legs with the device versus unoperated controls were significant; linear stiffnesses were not (p=0.3). We believe this technology will yield improved procedures for clinical challenges in orthopedic oncology, revision arthroplasty, tendon transfer, and tendon injury reconstruction. Copyright © 2011 Orthopaedic Research Society.

GMMIP (v1.0) contribution to CMIP6: Global Monsoons Model Inter-comparison Project

NASA Astrophysics Data System (ADS)

Zhou, Tianjun; Turner, Andrew G.; Kinter, James L.; Wang, Bin; Qian, Yun; Chen, Xiaolong; Wu, Bo; Wang, Bin; Liu, Bo; Zou, Liwei; He, Bian

2016-10-01

The Global Monsoons Model Inter-comparison Project (GMMIP) has been endorsed by the panel of Coupled Model Inter-comparison Project (CMIP) as one of the participating model inter-comparison projects (MIPs) in the sixth phase of CMIP (CMIP6). The focus of GMMIP is on monsoon climatology, variability, prediction and projection, which is relevant to four of the "Grand Challenges" proposed by the World Climate Research Programme. At present, 21 international modeling groups are committed to joining GMMIP. This overview paper introduces the motivation behind GMMIP and the scientific questions it intends to answer. Three tiers of experiments, of decreasing priority, are designed to examine (a) model skill in simulating the climatology and interannual-to-multidecadal variability of global monsoons forced by the sea surface temperature during historical climate period; (b) the roles of the Interdecadal Pacific Oscillation and Atlantic Multidecadal Oscillation in driving variations of the global and regional monsoons; and (c) the effects of large orographic terrain on the establishment of the monsoons. The outputs of the CMIP6 Diagnostic, Evaluation and Characterization of Klima experiments (DECK), "historical" simulation and endorsed MIPs will also be used in the diagnostic analysis of GMMIP to give a comprehensive understanding of the roles played by different external forcings, potential improvements in the simulation of monsoon rainfall at high resolution and reproducibility at decadal timescales. The implementation of GMMIP will improve our understanding of the fundamental physics of changes in the global and regional monsoons over the past 140 years and ultimately benefit monsoons prediction and projection in the current century.

Spontaneous Symmetry Breaking as a Basis of Particle Mass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quigg, Chris; /Fermilab /CERN

2007-04-01

Electroweak theory joins electromagnetism with the weak force in a single quantum field theory, ascribing the two fundamental interactions--so different in their manifestations--to a common symmetry principle. How the electroweak gauge symmetry is hidden is one of the most urgent and challenging questions facing particle physics. The provisional answer incorporated in the ''standard model'' of particle physics was formulated in the 1960s by Higgs, by Brout & Englert, and by Guralnik, Hagen, & Kibble: The agent of electroweak symmetry breaking is an elementary scalar field whose self-interactions select a vacuum state in which the full electroweak symmetry is hidden, leavingmore » a residual phase symmetry of electromagnetism. By analogy with the Meissner effect of the superconducting phase transition, the Higgs mechanism, as it is commonly known, confers masses on the weak force carriers W{sup {+-}} and Z. It also opens the door to masses for the quarks and leptons, and shapes the world around us. It is a good story--though an incomplete story--and we do not know how much of the story is true. Experiments that explore the Fermi scale (the energy regime around 1 TeV) during the next decade will put the electroweak theory to decisive test, and may uncover new elements needed to construct a more satisfying completion of the electroweak theory. The aim of this article is to set the stage by reporting what we know and what we need to know, and to set some ''Big Questions'' that will guide our explorations.« less

Translations on Eastern Europe, Political, Sociological, and Military Affairs, Number 1494

DTIC Science & Technology

1978-01-12

the joining of scientific forces together to achieve it. A New Process for the Chemical Industry In this way...possibility of paid exemption from work until the first birthday of the second and every additional child. The fact that the 40- hour workweek has taken...34 Time has proven us right and " the new ," helped by these journals, has proven to be a terrible fiasco. The price? Human lives . I wonder why

An Analysis of the Effectiveness of the Air Force Drug Testing Program and Four Potential Modifications

DTIC Science & Technology

1993-09-01

attempted to control substance abuse. In the 1920’s and 30’s, marijuana was commonly used as a substitute for alcohol during prohibition (1:4-7). In...discovered D-lysergic acia tiiethylamide (LSD), methaqualone (quaalude), and phencyclidine (PCP) joined heroin, amphetamines, and marijuana as drugs abused...themselves in Southeast Asia where drugs were plentiful and cheap. The most commonly used drugs were heroin and marijuana . Initially, the DOD policy

NATO 2000: The Role of the Spanish Air Force

DTIC Science & Technology

1989-05-01

the air space and how this control will be in Spanish strategic areas in the year 2000. The final con - clusions are the significant role of the...like an um- bilical cord which joins Europe with America. If Europe is con - sidered as a possible theater of operations, Spain must be a friend...announced the Strategic Defense Initi- ative (SDI) in 1983. SDI provoked in Europe, disquiet and con - fusion, especially in France and England. The

Malaria Capacity Building in Liberia: The US Navy Joins Forces to Defeat a Deadly Foe

DTIC Science & Technology

2014-01-01

Naval Medical Research Unit No. 3 (NAMRU-3) and the Liberian Institute for Biomedical Research (LIBR) to deliver a two-week Public Health and Vector...3. This facilitated maneu- vering throughout the buildings, Figure 3: Liberians living on EBK military barracks removed their furniture and...with Liberia over four years ago, there have been enormous strides by the Liberians to turn the tide against malaria after long and brutal civil wars

Mali’s Next Battle: Improving Counterterrorism Capabilities

DTIC Science & Technology

2017-01-01

most notably nonnoble and non –Kel Adagh clans—and Arab communities joined the fight, with the Arabs form- ing their own rebel group . On April 11...between pro-government and CMA forces Area controlled by jihadist groups in 2012–2013 TOGO COTE D’IVOIRE GHANA SIERRA LEONE BENIN NIGERIA...northern Mali’s larger security issues, both because of ties between and among terrorist and non -jihadi rebel groups —the signatories of the Algiers

A Wind Tunnel Investigation of Joined Wing Scissor Morphing

DTIC Science & Technology

2006-06-01

would use the low sweep for carrier landing and subsonic cruise, and use the high sweep for 12 supersonic flight [13]. According to Raymer [19...Wright-Patterson AFB, Ohio: Air Force Institute of Technology, 2005. 12. Katz, Joseph, Shaun Byrne, and Robert Hahl. "Stall Resistance Features of...Lifting-Body Airplane Configurations." Journal of Aircraft 2nd ser. 36 (1999): 471-474. 13. Kress, Robert W. "Variable Sweep Wing Design." AIAA 83

International Space Station (ISS)

NASA Image and Video Library

2007-06-15

Construction resumed on the International Space Station (ISS), as STS-117 astronauts and mission specialists Jim Reilly (on robotic arm), and John “Danny” Olivas joined forces with their colleagues inside the Shuttle and station, and controllers in Houston, to complete the delicate process of folding an older solar array, Port 6 (P6), so that it can be moved from its temporary location to its permanent home during an upcoming Fall scheduled Shuttle mission. The EVA lasted nearly 8 hours.

Mechanical Properties of Laser Beam Welded Ultra-high Strength Chromium Steel with Martensitic Microstructure

NASA Astrophysics Data System (ADS)

Dahmen, Martin; Janzen, Vitalij; Lindner, Stefan; Wagener, Rainer

A new class of steels is going to be introduced into sheet manufacturing. Stainless ferritic and martensitic steels open up opportunities for sheet metal fabrication including hot stamping. A strength of up to 2 GPa at a fracture strain of 15% can be attained. Welding of these materials became apparently a challenge. Energy-reduced welding methods with in-situ heat treatment are required in order to ensure the delicate and complex heat control. Laser beam welding is the joining technique of choice to supply minimum heat input to the fusion process and to apply an efficient heat control. For two application cases, production of tailored blanks in as-rolled condition and welding in assembly in hot stamped conditions, welding processes have been developed. The welding suitability is shown in metallurgical investigations of the welds. Crash tests based on the KSII concept as well as fatigue tests prove the applicability of the joining method. For the case of assembly also joining with deep drawing and manganese boron steel was taken into consideration. The strength of the joint is determined by the weaker partner but can benefit from its ductility.

Aeroservoelastic Wind-Tunnel Tests of a Free-Flying, Joined-Wing SensorCraft Model for Gust Load Alleviation

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Castelluccio, Mark A.; Coulson, David A.; Heeg, Jennifer

2011-01-01

A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind-tunnel model of a joined-wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind-tunnel model was mated to a new, two-degree-of-freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at -10% static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free ying wind-tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

KENNEDY SPACE CENTER, FLA. - On Launch Complex 17-B, Cape Canaveral Air Force Station, a solid rocket booster (SRB) is lifted into the mobile service tower, joining two others. They are three of nine 46-inch-diameter, stretched SRBs that are being attached to the Delta II Heavy rocket that will launch the Space Infrared Telescope Facility (SIRTF). Consisting of three cryogenically cooled science instruments and an 0.85-meter telescope, SIRTF is one of NASA's largest infrared telescopes to be launched. SIRTF will obtain images and spectra by detecting the infrared energy, or heat, radiated by objects in space. Most of this infrared radiation is blocked by the Earth's atmosphere and cannot be observed from the ground.

NASA Image and Video Library

2003-07-22

KENNEDY SPACE CENTER, FLA. - On Launch Complex 17-B, Cape Canaveral Air Force Station, a solid rocket booster (SRB) is lifted into the mobile service tower, joining two others. They are three of nine 46-inch-diameter, stretched SRBs that are being attached to the Delta II Heavy rocket that will launch the Space Infrared Telescope Facility (SIRTF). Consisting of three cryogenically cooled science instruments and an 0.85-meter telescope, SIRTF is one of NASA's largest infrared telescopes to be launched. SIRTF will obtain images and spectra by detecting the infrared energy, or heat, radiated by objects in space. Most of this infrared radiation is blocked by the Earth's atmosphere and cannot be observed from the ground.

Analysis of the Change of Health Status Among the Republic of Korea Air Force Soldiers During Military Service

PubMed Central

Yoo, Seok-Ju; Park, Won-Ju; Lee, Kwan; Lim, Hyun-Sul; Kim, Hyun-Jin; Lee, Suk-Ho

2014-01-01

Objectives: The aim of this study was to investigate whether the health status of Republic of Korea Air Force (ROKAF) soldiers changed after one year of military service. Methods: We selected 483 ROKAF soldiers from the 11 749 recruits who participated in the 2011 physical examination. The selected soldiers underwent another physical examination in 2012 for advancement to senior airman. Data from 2011 and 2012 were merged. To collect data on lifestyle, a questionnaire was sent to all included subjects via the military intranet e-mail service. Results: The percentage of recruits with an abnormal alanine transaminase level (normal range <40 IU/L) decreased from recruitment (13.7%) to the following year (2.7%). Moreover, the percentage of obese soldiers (body mass index ≥25 kg/m2) decreased from recruitment (20.5%) to the following year (10.4%). There was a significant change in mean duration of exercise carried out each day before (0.8±1.3 hours) and after (1.0±0.7 hours) joining the ROKAF service. Conclusions: These ROKAF soldiers were generally in good health before and after joining the armed service. After one year of military service, the health status of most soldiers improved, especially with respect to body mass index and alanine transaminase level. PMID:25139169

Induction and repair of DNA double strand breaks: the increasing spectrum of non-homologous end joining pathways.

PubMed

Mladenov, Emil; Iliakis, George

2011-06-03

A defining characteristic of damage induced in the DNA by ionizing radiation (IR) is its clustered character that leads to the formation of complex lesions challenging the cellular repair mechanisms. The most widely investigated such complex lesion is the DNA double strand break (DSB). DSBs undermine chromatin stability and challenge the repair machinery because an intact template strand is lacking to assist restoration of integrity and sequence in the DNA molecule. Therefore, cells have evolved a sophisticated machinery to detect DSBs and coordinate a response on the basis of inputs from various sources. A central function of cellular responses to DSBs is the coordination of DSB repair. Two conceptually different mechanisms can in principle remove DSBs from the genome of cells of higher eukaryotes. Homologous recombination repair (HRR) uses as template a homologous DNA molecule and is therefore error-free; it functions preferentially in the S and G2 phases. Non-homologous end joining (NHEJ), on the other hand, simply restores DNA integrity by joining the two ends, is error prone as sequence is only fortuitously preserved and active throughout the cell cycle. The basis of DSB repair pathway choice remains unknown, but cells of higher eukaryotes appear programmed to utilize preferentially NHEJ. Recent work suggests that when the canonical DNA-PK dependent pathway of NHEJ (D-NHEJ), becomes compromised an alternative NHEJ pathway and not HRR substitutes in a quasi-backup function (B-NHEJ). Here, we outline aspects of DSB induction by IR and review the mechanisms of their processing in cells of higher eukaryotes. We place particular emphasis on backup pathways of NHEJ and summarize their increasing significance in various cellular processes, as well as their potential contribution to carcinogenesis. 2011 Elsevier B.V. All rights reserved.

Applied Theatre Facilitates Dialogue about Career Challenges for Scientists.

PubMed

Segarra, Verónica A; Zavala, MariaElena; Hammonds-Odie, Latanya

2017-04-01

The design of programs in support of a strong, diverse, and inclusive scientific workforce and academe requires numerous difficult conversations about sensitive topics such as the challenges scientists can face in their professional development. Theatre can be an interactive and effective way to foster discussion around such subjects. This article examines the implementation and benefits of such interactive strategies in different contexts, including the benefits of getting early career academics and professionals talking about some of the situations that women and underrepresented minorities face in the workplace, while allowing more seasoned professionals and colleagues to join in the conversation.

Applied Theatre Facilitates Dialogue about Career Challenges for Scientists†

PubMed Central

Segarra, Verónica A.; Zavala, MariaElena; Hammonds-Odie, Latanya

2017-01-01

The design of programs in support of a strong, diverse, and inclusive scientific workforce and academe requires numerous difficult conversations about sensitive topics such as the challenges scientists can face in their professional development. Theatre can be an interactive and effective way to foster discussion around such subjects. This article examines the implementation and benefits of such interactive strategies in different contexts, including the benefits of getting early career academics and professionals talking about some of the situations that women and underrepresented minorities face in the workplace, while allowing more seasoned professionals and colleagues to join in the conversation. PMID:28656070

KSC-2010-1273

NASA Image and Video Library

2010-01-15

CAPE CANAVERAL, Fla. - A green sea turtle rests its head on a companion as the animals are tagged with tracking transmitters and prepared for release at Cape Canaveral Air Force Station in Florida. The turtles were some of nearly 2,000 that were "stunned" by the recent drop in temperatures. Many of the turtles were rescued from the Mosquito Lagoon, with others coming from the Indian River Lagoon and Cocoa Beach. Biologists, environmentalists, wildlife experts and other volunteers joined forces with a massive rescue effort at the Merritt Island National Wildlife Refuge, where the turtles were identified, examined and transported to rehabilitation facilities throughout Florida and South Georgia. The animals stayed at these facilities until local waters warmed up to safe temperatures. Photo credit: NASA/Jack Pfaller

Study of the joining of polycarbonate panels in butt joint configuration through friction stir welding

NASA Astrophysics Data System (ADS)

Astarita, Antonello; Boccarusso, Luca; Carrino, Luigi; Durante, Massimo; Minutolo, Fabrizio Memola Capece; Squillace, Antonino

2018-05-01

Polycarbonate sheets, 3 mm thick, were successfully friction stir welded in butt joint configuration. Aiming to study the feasibility of the process and the influence of the process parameters joints under different processing conditions, obtained by varying the tool rotational speed and the tool travel speed, were realized. Tensile tests were carried out to characterize the joints. Moreover the forces arising during the process were recorded and carefully studied. The experimental outcomes proved the feasibility of the process when the process parameters are properly set, joints retaining more than 70% of the UTS of the base material were produced. The trend of the forces was described and explained, the influence of the process parameters was also introduced.

Self-erecting shapes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reading, Matthew W.

Technologies for making self-erecting structures are described herein. An exemplary self-erecting structure comprises a plurality of shape-memory members that connect two or more hub components. When forces are applied to the self-erecting structure, the shape-memory members can deform, and when the forces are removed the shape-memory members can return to their original pre-deformation shape, allowing the self-erecting structure to return to its own original shape under its own power. A shape of the self-erecting structure depends on a spatial orientation of the hub components, and a relative orientation of the shape-memory members, which in turn depends on an orientation ofmore » joining of the shape-memory members with the hub components.« less

The equivalent angle-of-attack method for estimating the nonlinear aerodynamic characteristics of missile wings and control surfaces

NASA Technical Reports Server (NTRS)

Hemsch, M. J.; Nielsen, J. N.

1982-01-01

A method has been developed for estimating the nonlinear aerodynamic characteristics of missile wing and control surfaces. The method is based on the following assumption: if a fin on a body has the same normal-force coefficient as a wing alone composed of two of the same fins joined together at their root chords, then the other force and moment coefficients of the fin and the wing alone are the same including the nonlinearities. The method can be used for deflected fins at arbitrary bank angles and at high angles of attack. In the paper, a full derivation of the method is given, its accuracy demonstrated and its use in extending missile data bases is shown.

KSC-2011-1349

NASA Image and Video Library

2011-02-02

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once the spacecraft reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Don Kososka, VAFB

KSC-2011-1117

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, technicians prepare to transfer NASA's Glory spacecraft to a processing dolly. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1353

NASA Image and Video Library

2011-02-02

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft is revealed after technicians removed the protective covering surrounding it. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once the spacecraft reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Don Kososka, VAFB

KSC-2011-1114

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, technicians prepare to remove the shipping container surrounding NASA's Glory spacecraft. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1118

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft is transferring to a processing dolly. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1113

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, the shipping container surrounding NASA's Glory spacecraft is ready for removal. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1115

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, technicians remove the shipping container surrounding NASA's Glory spacecraft. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1119

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft is situated on a dolly and ready for processing. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1352

NASA Image and Video Library

2011-02-02

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, NASA's Glory spacecraft is revealed after technicians removed the protective covering surrounding it. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once the spacecraft reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Don Kososka, VAFB

KSC-2011-1116

NASA Image and Video Library

2011-01-12

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech processing facility at Vandenberg Air Force Base in California, technicians remove the shipping container surrounding NASA's Glory spacecraft. Next, technicians will take off Glory's protective covering before it is encapsulated in a protective payload fairing for flight. In early February, Glory is scheduled to be transported Space Launch Complex 576-E where it will be joined with the Taurus XL rocket, which is manufactured by Orbital Sciences Corp. Once Glory reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Ed Henry, VAFB

KSC-2011-1350

NASA Image and Video Library

2011-02-02

VANDENBERG AIR FORCE BASE, Calif. -- Inside the Astrotech payload processing facility at Vandenberg Air Force Base in California, technicians removed most of the protective covering surrounding NASA's Glory spacecraft. Next, the spacecraft will be encapsulated in its protective payload fairing before it is transported to Space Launch Complex 576-E and joined with the Taurus XL rocket's third stage. The Orbital Sciences Corp. Taurus XL rocket will carry Glory into low Earth orbit. Once the spacecraft reaches orbit, it will collect data on the properties of aerosols and black carbon. It also will help scientists understand how the sun's irradiance affects Earth's climate. Launch is scheduled for 5:09 a.m. EST Feb. 23. For information, visit www.nasa.gov/glory. Photo credit: NASA/Don Kososka, VAFB

Dynamics of ultrasonic additive manufacturing.

PubMed

Hehr, Adam; Dapino, Marcelo J

2017-01-01

Ultrasonic additive manufacturing (UAM) is a solid-state technology for joining similar and dissimilar metal foils near room temperature by scrubbing them together with ultrasonic vibrations under pressure. Structural dynamics of the welding assembly and work piece influence how energy is transferred during the process and ultimately, part quality. To understand the effect of structural dynamics during UAM, a linear time-invariant model is proposed to relate the inputs of shear force and electric current to resultant welder velocity and voltage. Measured frequency response and operating performance of the welder under no load is used to identify model parameters. Using this model and in-situ measurements, shear force and welder efficiency are estimated to be near 2000N and 80% when welding Al 6061-H18 weld foil, respectively. Shear force and welder efficiency have never been estimated before in UAM. The influence of processing conditions, i.e., welder amplitude, normal force, and weld speed, on shear force and welder efficiency are investigated. Welder velocity was found to strongly influence the shear force magnitude and efficiency while normal force and weld speed showed little to no influence. The proposed model is used to describe high frequency harmonic content in the velocity response of the welder during welding operations and coupling of the UAM build with the welder. Copyright © 2016 Elsevier B.V. All rights reserved.

Agriculture Development in Afghanistan: A Systemic Assessment Approach

DTIC Science & Technology

2010-04-14

Sponsoring programs to improve the health orpeople, livestock, and crops. 5. Distributing high-quality seeds and fertilizers.3 The USDA lists close to...weapons, and smuggling. The Taliban joined warlords and both entities offer credit, seeds , and fertilizer to farmers who grow and cultivated opium. The... seed , fertilizer, pesticide, storage, processing, and packaging; however, a review of the most challenging inputs validate the proposed assessment

The Reality of Evaluating Community-Based Sport and Physical Activity Programs to Enhance the Development of Underserved Youth: Challenges and Potential Strategies

ERIC Educational Resources Information Center

Whitley, Meredith A.; Forneris, Tanya; Barker, Bryce

2014-01-01

In recent years, underserved communities have received much attention within the field of positive youth development (PYD). While there are an increasing number of opportunities for underserved youth to join PYD-based programs, there is growing concern surrounding the lack of critical evaluation of these programs (Kidd, 2008). Unfortunately, there…

A Vision for High Schools: Joining Academic and Technical Studies to Promote More Powerful Learning

ERIC Educational Resources Information Center

Bottoms, Gene

2008-01-01

One in four American students does not graduate from high school on time, if at all. Many of these young people blame schoolwork that failed to challenge them and assignments that meant nothing in their lives. More surprising are the large numbers of students who graduate from high school and enter college but do not receive a degree. They drop…

A novel population of Fusarium fujikuroi isolated from southeastern U.S. winegrapes reveals the need to re-evaluate the species’ fumonisin production

USDA-ARS?s Scientific Manuscript database

Mycotoxins pose a challenge to a safe food supply worldwide, and their threat is expected to worsen with our changing climate. The need for diligence is exemplified by the discovery of fumonisin B2 in wine, which joins ochratoxin A as a mycotoxin of concern in the grape-wine chain. To elucidate th...

When Is Russia Joining NATO Russian Security Orientation in the Twenty-first Century

DTIC Science & Technology

2010-06-01

around the world and makes its products - ranging from textual translations to multimedia productions - available to customers throughout the United...of economic, political, and social restructuring, became the unintended catalyst for dismantling what had taken nearly three-quarters of a century... dissatisfaction with Russia. The most vocal and sensitive nations are the Baltic nations. This tension will be challenging for NATO-Russia

It Takes a Network to Raise a Child: Improving the Communication Infrastructure of Public Education to Enable Community Cooperation in Young People's Success

ERIC Educational Resources Information Center

Pollock, Mica

2013-01-01

Background/Context: In this essay, I propose a design research agenda that braids equity research and technology research in education. More specifically, I propose that researchers join educators, youth, families, and community partners in tackling a central challenge for education research today: figuring out how and when low-cost and…

Some of the challenges of teaching multilevel classes and suggestions for how to deal with the situation

NASA Astrophysics Data System (ADS)

Demarcsek, R.; Todea, L.

2016-08-01

Teaching English to Engineering or Business students has always been a challenge. One of the major reasons which makes this task particularly challenging is the fact that, being graduates of various high schools, they join the university having very different levels of English. Some may have started English in kindergarten, while others only in high school. Some speak it fluently; others may barely be able to introduce themselves despite having studied it for a similar number of years as the former. This paper takes a look at the major challenges teachers of English in university are faced with when teaching multilevel classes, and attempts to offer some suggestions as to how to deal with this situation while at the same time keeping the quality of the teaching-learning process.

Apparatus and method for performing microfluidic manipulations for chemical analysis

DOEpatents

Ramsey, J. Michael

1999-01-01

A microchip apparatus and method provide fluidic manipulations for a variety of applications, including sample injection for microchip liquid chromatography. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis is performed in channels formed in the substrate. Injections are made by electro-osmotically pumping sample through the injection channel that crosses the separation channel, followed by a switching of the potentials to force a plug into the separation channel.

Apparatus and method for performing microfluidic manipulations for chemical analysis

DOEpatents

Ramsey, J. Michael

2002-01-01

A microchip apparatus and method provide fluidic manipulations for a variety of applications, including sample injection for microchip liquid chromatography. The microchip is fabricated using standard photolitographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis is performed in channels formed in the substrate. Injections are made by electro-osmotically pumping sample through the injection channel that crosses the separation channel, followed by a switching of the potentials to force a plug into the separation channel.

Surface Warfare: A Total Force. Volume 19. Number 4, July/August 1994

DTIC Science & Technology

1994-08-01

USS Puget Sound (AD 38) (AOE 1) Support USS Grasp (ARS 51) Combat Logistics (med/small) USS Mauna Lea (AE 22) COMINEWARCOM: Repair USS Acadia (AD 42...structure is Operational Reserve Carrier ( ORC ). When USS John being shaped to expand this role. In the recently P. Eznnedy (CV 67) joins the NRF in...A typical Aegis engagement sequence begins as a engineer and test the fought in the waters of Port RoyalAegis Combat System. Sound and on the adjacent

The Crimean Tatars and Their Influence on the Triangle of Conflict’ - Russia-Crimea-Ukraine

DTIC Science & Technology

2008-03-01

Ottoman Empire, threatening the strategic Bosporus Straits. To protect them, France , Britain and Sardinia joined the Ottomans in the war. Allied forces...educated in a local Islamic school, and then in Russia and France .259 He recognized the threat of Russification, and sought to counter it through a...269 On the other hand, Lenin claimed Crimea was a hive of bourgeoisie , and sent the Cheka (Soviet secret police) to deal with those who opposed the

InSight Prelaunch

NASA Image and Video Library

2018-05-04

American professional basketball player Chris Bosh poses for a photograph in front of the United Launch Alliance (ULA) Atlas-V rocket with NASA's InSight spacecraft onboard, Friday, May 4, 2018, at Vandenberg Air Force Base in California. Bosh joined other social media guests on a behind the scenes tour ahead of the planned launch. InSight, short for Interior Exploration using Seismic Investigations, Geodesy and Heat Transport, is a Mars lander designed to study the "inner space" of Mars: its crust, mantle, and core. Photo Credit: (NASA/Bill Ingalls)

Women Combatants in World War I: A Russian Case Study

DTIC Science & Technology

2003-04-07

interesting to note that the phenomenal number of over 80,000 women served as soldiers in the Red Army against the White anti-communist forces.3 Russia’s...to enlist. But the adjutant declared, “The regulations do not permit us to enlist women . It is against the law.”69 The commander of the reserve... variety of women who volunteered to join and fight for the survival of Russia ranged across the entire socioeconomic spectrum. The Battalion included

Al-Shebab: An Al-Qaeda Affiliate Case Study (2Rev)

DTIC Science & Technology

2017-10-01

explosives and car bombs . Al-Shebab’s joining Al-Qaeda had mutual benefits: AQ’s presence in East Africa dates to Osama Bin Laden’s time in Sudan...1992–1996) and the establishment of cells that perpetrated the August 7, 1998 bombings of the U.S. embassies in Nairobi, Kenya, and Dar es Salaam...to build an emirate in the Gedo region, but the project was crushed by Ethiopian forces after AIAI perpetrated several bombings in Ethiopia.25 The

The West-African Special Operations Forces: Development and Integration in the Context of the Sub-Saharan Growing Threats

DTIC Science & Technology

2016-06-10

solutions to African problems.” In light of these aforementioned factors and given the low GDP of these nations and their difficulty in financing ...difficulty in financing needed operations and capabilities, the West African nations need to join their efforts in order to find a way to achieve a unified...which include the ability to finance international terrorism (UN General Assembly 2001). The close collaboration between the European countries and

Ukraine After the Orange Revolution: Can It Complete Military Transformation and Join the U.S.-Led War on Terrorism?

DTIC Science & Technology

2006-10-01

podolaty!” The rhythmic chant spread through the crowd of hundreds of thousands that filled Kiev’s Independence Square on the evening of November 22... analysis of official documents.15 By means of a case study of the attack by Al Sadr forces on the Coalition Provisional Authority (CPA) compound in Wasit...to raise social benefits, pensions, and wages, but its administrative methods have affected business, the investment climate , and economic growth

An Analysis in Coalition Warfare: Napoleon’s Defeat at the Battle of Nations-Leipzig, 1813.

DTIC Science & Technology

1998-04-06

modern day Northern Poland and Eastern Germany . The Prussian monarch, Frederick William III, another unwilling ally to Napoleon’s invasion of...but in Germany , England’s stake in the battle was the financial support it provided the allies34, liaison officers, and a small number of troops...signed the Treaty of Kalisch on 27 February 1813 and joined Russian forces on the offensive, resulting in an inconclusive battle at Magdeburg . This

U. S. Naval Forces, Vietnam Monthly Historical Summary for December 1966

DTIC Science & Technology

1967-02-15

the northwest tip of Cu Lao May, three and one half miles southeast of Can Tho. The sampan Ignored halls and warning shots and continued to evade...machine gun. The patrol cleared the area to the southeast , returning fire as it withdrew. PBRs 86 and 97 joined the engagement and came under fire from...the south bank» ine four PBRs then stood by to the southeast of the kill zone as the Cang Long sub-sector artillery battery fired eight rounds of

What do Afghans Want from the Police? Views from Helmand Province

DTIC Science & Technology

2012-01-01

AUTHOR(S) Norman, Catherine 5d PROJECT NUMBER R0148 5e. TASK NUMBER W053 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS...ES) Center for Naval Analyses 4825 Mark Center Drive Alexandria, VA 22311-1850 8. PERFORMING ORGANIZATION REPORT NUMBER D0026181.A2 9... organizations are expected to trump local values. For instance, when a person joins a city police force, he or she is expected to sub- ordinate the

American Sammys and French Poilus in the Great War: sport, masculinities and vulnerability.

PubMed

Terret, Thierry

2011-01-01

The violence and duration of fighting throughout the Great War created an intense feeling of vulnerability among the men engaged in battle, which challenged their perception of manliness. When the Americans joined the war in 1917, the balance between the two opposing armies was modified and the psychological crises of French soldiers brought to an end. The confidence shown by the American soldiers and their first successes on the battlefield changed the way the French Poilus perceived their new allies. From scepticism to admiration, Frenchmen's feelings extended beyond the fighting. Indeed, by living with American soldiers in the trenches and camps behind the front, French soldiers discovered a new culture where games and sport played a major role and contributed to building manliness. The Foyers Franco-Americains du Soldat (Franco-American hostels for soldiers) provided an ideal place for the cultural transfer of a model of masculinity from Sammys to Poilus. The foyers were managed by the American YMCA and eventually reached the number of 1,500 in France during the war. These hostels afforded soldiers numerous opportunities to develop cultural and sports practices, by bringing together Americans and Frenchmen. Mainly based on the archives of the American Expeditionary Forces, the YMCA and the French Army, the paper argues that the Foyers du Soldat brought to light a new model of masculinity based on sport, which challenged the Frenchmen's vision. It aims to show the rapid transformation of masculine identity within a context of extreme vulnerability and confirms the changes in representations of men in French society at this time.

Recruitment of child soldiers in Nepal: Mental health status and risk factors for voluntary participation of youth in armed groups.

PubMed

Kohrt, Brandon A; Yang, Minyoung; Rai, Sauharda; Bhardwaj, Anvita; Tol, Wietse A; Jordans, Mark J D

2016-08-01

Preventing involuntary conscription and voluntary recruitment of youth into armed groups are global human rights priorities. Pathways for self-reported voluntary recruitment and the impact of voluntary recruitment on mental health have received limited attention. The objective of this study was to identify risk factors for voluntarily joining armed groups, as well as the association of conscription status and mental health. In Nepal, interviews were conducted with 258 former child soldiers who participated in a communist (Maoist) revolution. Eighty percent of child soldiers joined 'voluntarily'. Girls were 2.07 times as likely to join voluntarily (95% CI, 1.03-4.16, p =0.04). Among girls, 51% reported joining voluntarily because of personal connections to people who were members of the armed group, compared to 22% of boys. Other reasons included escaping difficult life situations (36%), inability to achieve other goals in life (28%), and an appealing philosophy of the armed group (32%). Poor economic conditions were more frequently endorsed among boys (22%) than girls (10%). Voluntary conscription was associated with decreased risk for PTSD among boys but not for girls. Interventions to prevent voluntary association with armed groups could benefit from attending to difficulties in daily life, identifying non-violent paths to achieve life goals, and challenging the political philosophy of armed groups. Among boys, addressing economic risk factors may prevent recruitment, and prevention efforts for girls will need to address personal connections to armed groups, as it has important implications for preventing recruitment through new methods, such as social media.

Joining, Leaving, and Staying in the American Indian/Alaska Native Race Category between 2000 and 2010

PubMed Central

Liebler, Carolyn A.; Bhaskar, Renuka; Porter (née Rastogi), Sonya R.

2017-01-01

Conceptualizing and operationalizing American Indian populations is challenging. Each census for decades has seen the American Indian population increase substantially more than expected, with indirect and qualitative evidence that this is due to changes in individuals' race responses. We apply uniquely suited (but not nationally representative) linked data from the 2000 and 2010 decennial censuses (N= 3.1 million) and the 2006–2010 American Community Survey (N = 188,131) to address three research questions. First, to what extent do American Indian people have different race responses across data sources? We find considerable race response change, especially among multiple-race and/or Hispanic American Indians. Second, how are people who change responses different from or similar to those who do not? We find three sets of American Indians: those who (1) had the same race and Hispanic responses in 2000 and 2010, (2) moved between single-race and multiple-race American Indian responses, and (3) added or dropped the American Indian response, thus joining or leaving the enumerated American Indian population. People in groups (1) and (2) were relatively likely to report a tribe, live in an American Indian area, report American Indian ancestry, and live in the West. Third, how are people who join a group different from or similar to those who leave it? Multivariate models show general similarity between joiners and leavers in group (1) and in group (2). Population turnover is hidden in cross-sectional comparisons; people joining each subpopulation of American Indians are similar in number and characteristics to those who leave it. PMID:26988712

Joining, Leaving, and Staying in the American Indian/Alaska Native Race Category Between 2000 and 2010.

PubMed

Liebler, Carolyn A; Bhaskar, Renuka; Porter, Sonya R

2016-04-01

Conceptualizing and operationalizing American Indian populations is challenging. Each census for decades has seen the American Indian population increase substantially more than expected, with indirect and qualitative evidence that this is due to changes in individuals' race responses. We apply uniquely suited (but not nationally representative) linked data from the 2000 and 2010 decennial censuses (N = 3.1 million) and the 2006-2010 American Community Survey (N = 188,131) to address three research questions. First, to what extent do American Indian people have different race responses across data sources? We find considerable race response change, especially among multiple-race and/or Hispanic American Indians. Second, how are people who change responses different from or similar to those who do not? We find three sets of American Indians: those who (1) had the same race and Hispanic responses in 2000 and 2010, (2) moved between single-race and multiple-race American Indian responses, and (3) added or dropped the American Indian response, thus joining or leaving the enumerated American Indian population. People in groups (1) and (2) were relatively likely to report a tribe, live in an American Indian area, report American Indian ancestry, and live in the West. Third, how are people who join a group different from or similar to those who leave it? Multivariate models show general similarity between joiners and leavers in group (1) and in group (2). Population turnover is hidden in cross-sectional comparisons; people joining each subpopulation of American Indians are similar in number and characteristics to those who leave it.

Recruitment of child soldiers in Nepal: Mental health status and risk factors for voluntary participation of youth in armed groups

PubMed Central

Kohrt, Brandon A.; Yang, Minyoung; Rai, Sauharda; Bhardwaj, Anvita; Tol, Wietse A.; Jordans, Mark J. D.

2016-01-01

Preventing involuntary conscription and voluntary recruitment of youth into armed groups are global human rights priorities. Pathways for self-reported voluntary recruitment and the impact of voluntary recruitment on mental health have received limited attention. The objective of this study was to identify risk factors for voluntarily joining armed groups, as well as the association of conscription status and mental health. In Nepal, interviews were conducted with 258 former child soldiers who participated in a communist (Maoist) revolution. Eighty percent of child soldiers joined ‘voluntarily’. Girls were 2.07 times as likely to join voluntarily (95% CI, 1.03–4.16, p=0.04). Among girls, 51% reported joining voluntarily because of personal connections to people who were members of the armed group, compared to 22% of boys. Other reasons included escaping difficult life situations (36%), inability to achieve other goals in life (28%), and an appealing philosophy of the armed group (32%). Poor economic conditions were more frequently endorsed among boys (22%) than girls (10%). Voluntary conscription was associated with decreased risk for PTSD among boys but not for girls. Interventions to prevent voluntary association with armed groups could benefit from attending to difficulties in daily life, identifying non-violent paths to achieve life goals, and challenging the political philosophy of armed groups. Among boys, addressing economic risk factors may prevent recruitment, and prevention efforts for girls will need to address personal connections to armed groups, as it has important implications for preventing recruitment through new methods, such as social media. PMID:27524877

Nonlinear Aeroelastic Analysis of Joined-Wing Configurations

NASA Astrophysics Data System (ADS)

Cavallaro, Rauno

Aeroelastic design of joined-wing configurations is yet a relatively unexplored topic which poses several difficulties. Due to the overconstrained nature of the system combined with structural geometric nonlinearities, the behavior of Joined Wings is often counterintuitive and presents challenges not seen in standard layouts. In particular, instability observed on detailed aircraft models but never thoroughly investigated, is here studied with the aid of a theoretical/computational framework. Snap-type of instabilities are shown for both pure structural and aeroelastic cases. The concept of snap-divergence is introduced to clearly identify the true aeroelastic instability, as opposed to the usual aeroelastic divergence evaluated through eigenvalue approach. Multi-stable regions and isola-type of bifurcations are possible characterizations of the nonlinear response of Joined Wings, and may lead to branch-jumping phenomena well below nominal critical load condition. Within this picture, sensitivity to (unavoidable) manufacturing defects could have potential catastrophic effects. The phenomena studied in this work suggest that the design process for Joined Wings needs to be revisited and should focus, when instability is concerned, on nonlinear post-critical analysis since linear methods may provide wrong trend indications and also hide potentially catastrophical situations. Dynamic aeroelastic analyses are also performed. Flutter occurrence is critically analyzed with frequency and time-domain capabilities. Sensitivity to different-fidelity aeroelastic modeling (fluid-structure interface algorithm, aerodynamic solvers) is assessed showing that, for some configurations, wake modeling (rigid versus free) has a strong impact on the results. Post-flutter regimes are also explored. Limit cycle oscillations are observed, followed, in some cases, by flip bifurcations (period doubling) and loss of periodicity of the solution. Aeroelastic analyses are then carried out on a realistic PrantlPlane to understand effects induced by freeplay of mobile surfaces. Conclusive work is also performed to study the interaction between rigid body and elastic modes, assessing the occurrence of bodyfreedom flutter.

Probing the stereoselective interaction of ofloxacin enantiomers with corresponding monoclonal antibodies by multiple spectrometry

NASA Astrophysics Data System (ADS)

Mu, Hongtao; Xu, Zhenlin; Liu, Yingju; Sun, Yuanming; Wang, Baoling; Sun, Xiulan; Wang, Zhanhui; Eremin, Sergei; Zherdev, Anatoly V.; Dzantiev, Boris B.; Lei, Hongtao

2018-04-01

Although stereoselective antibody has immense potential in chiral compounds detection and separation, the interaction traits between stereoselective antibody and the corresponding antigenic enantiomers are not yet fully exploited. In this study, the stereospecific interactions between ofloxacin isomers and corresponding monoclonal antibodies (McAb-WR1 and McAb-MS1) were investigated using time-resolved fluorescence, steady-state fluorescence, and circular dichroism (CD) spectroscopic methods. The chiral recognition discrepancies of antibodies with ofloxacin isomers were reflected through binding constant, number of binding sites, driving forces and conformational changes. The major interacting forces of McAb-WR1 and McAb-MS1 chiral interaction systems were hydrophobic force and van der Waals forces joined up with hydrogen bonds, respectively. Synchronous fluorescence spectra and CD spectra results showed that the disturbing of tyrosine and tryptophan micro-environments were so slightly that no obvious secondary structure changes were found during the chiral hapten binding. Clarification of stereospecific interaction of antibody will facilitate the application of immunoassay to analyze chiral contaminants in food and other areas.

KSC-07pd3124

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Crowds fill the areas along NASA Causeway at NASA's Kennedy Space Center to watch the World Space Expo aerial salute. Aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydivers. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3134

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- One of the U.S. Navy F-18 Super Hornets flies over NASA's Kennedy Space Center as part of the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydiving team. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3136

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Crowds at NASA's Kennedy Space Center watch the U.S. Air Force Thunderbirds Demonstration Squadron perform during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydivers. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3128

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Members of the U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3116

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3137

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Crowds at NASA's Kennedy Space Center watch the U.S. Air Force Thunderbirds Demonstration Squadron perform during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydivers. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3120

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, the U.S. Air Force Thunderbirds Demonstration Squadron performs during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3114

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3115

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3131

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- A member of the U.S. Army Golden Knights demonstrates precision landing as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3119

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, the U.S. Air Force Thunderbirds Demonstration Squadron performs during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3122

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, the U.S. Navy F-18 Super Hornets demonstrate their formation flying during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3132

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Members of the U.S. Army Golden Knights demonstrate precision landing as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3117

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, a U.S. Air Force F-22 Raptor flies overhead as part of the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3138

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Air Force Thunderbirds Demonstration Squadron fly in close formation during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydivers. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3127

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- A member of the U.S. Army Golden Knights demonstrates precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3129

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- Crowds at NASA's Kennedy Space Center watch the U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3105

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. — This U.S. Air Force F-22 Raptor is part of an aerial salute for the World Space Expo at NASA's Kennedy Space Center Visitor Complex. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, the U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/George Shelton

KSC-07pd3121

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, the U.S. Air Force Thunderbirds Demonstration Squadron performs during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3118

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- At NASA's Kennedy Space Center, a P-51 Mustang keeps pace with a U.S. Air Force F-22 Raptor during the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-15 Eagle, the U.S. Air Force 920th Rescue wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights demonstrating precision skydiving. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Chris Chamberland

KSC-07pd3135

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Air Force Thunderbirds Demonstration Squadron flies in formation over NASA's Kennedy Space Center as part of the World Space Expo aerial salute. Other aircraft joining in the expo salute include the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery, and the U.S. Army Golden Knights precision skydiving team. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

KSC-07pd3130

NASA Image and Video Library

2007-11-04

KENNEDY SPACE CENTER, FLA. -- The U.S. Army Golden Knights demonstrate precision skydiving as part of the World Space Expo aerial salute at NASA's Kennedy Space Center. Other aircraft joining in the expo salute include the U.S. Air Force Thunderbirds Demonstration Squadron, the U.S. Navy F-18 Super Hornets, U.S. Air Force F-22 Raptor, U.S. Air Force F-15 Eagle, P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The World Space Expo held Nov. 1-4 was an event commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond. The expo showcased various panels, presentations and educational programs. It also was a part of NASA's 50th anniversary celebrations, highlighting the 45th Anniversary of the Mercury Program celebration featuring original NASA astronauts John Glenn and Scott Carpenter and the Pioneering Women of Aerospace forum featuring Eileen Collins and other prominent female space veterans. The agency was founded Oct. 1, 1958. Photo credit: NASA/Kim Shiflett

Laser Beam Welding of Ultra-high Strength Chromium Steel with Martensitic Microstructure

NASA Astrophysics Data System (ADS)

Dahmen, Martin; Janzen, Vitalij; Lindner, Stefan; Wagener, Rainer

A new class of steels is going to be introduced into sheet manufacturing. Stainless ferritic and martensitic steels open up opportunities for sheet metal fabrication including hot stamping. Strengths of up to 2 GPa at fracture elongations of 15% can be attained through this. Welding of these materials, as a result, became a challenge. Energy-reduced welding methods with in-situ heat treatment are required in order to ensure the delicate and complex heat control. Laser beam welding is the joining technique of choice to supply minimum heat input to the fusion process and to apply efficient heat control. For two application cases, tailored blank production in as-rolled condition and welding during assembly in hot stamped condition, welding processes have been developed. The welding suitability is shown through metallurgical investigations of the welds. Crash tests based on the KS-II concept as well as fatigue tests prove the applicability of the joining method.

LHC@Home: a BOINC-based volunteer computing infrastructure for physics studies at CERN

NASA Astrophysics Data System (ADS)

Barranco, Javier; Cai, Yunhai; Cameron, David; Crouch, Matthew; Maria, Riccardo De; Field, Laurence; Giovannozzi, Massimo; Hermes, Pascal; Høimyr, Nils; Kaltchev, Dobrin; Karastathis, Nikos; Luzzi, Cinzia; Maclean, Ewen; McIntosh, Eric; Mereghetti, Alessio; Molson, James; Nosochkov, Yuri; Pieloni, Tatiana; Reid, Ivan D.; Rivkin, Lenny; Segal, Ben; Sjobak, Kyrre; Skands, Peter; Tambasco, Claudia; Veken, Frederik Van der; Zacharov, Igor

2017-12-01

The LHC@Home BOINC project has provided computing capacity for numerical simulations to researchers at CERN since 2004, and has since 2011 been expanded with a wider range of applications. The traditional CERN accelerator physics simulation code SixTrack enjoys continuing volunteers support, and thanks to virtualisation a number of applications from the LHC experiment collaborations and particle theory groups have joined the consolidated LHC@Home BOINC project. This paper addresses the challenges related to traditional and virtualized applications in the BOINC environment, and how volunteer computing has been integrated into the overall computing strategy of the laboratory through the consolidated LHC@Home service. Thanks to the computing power provided by volunteers joining LHC@Home, numerous accelerator beam physics studies have been carried out, yielding an improved understanding of charged particle dynamics in the CERN Large Hadron Collider (LHC) and its future upgrades. The main results are highlighted in this paper.

Harriet Brooks: Canada's First Woman Physicist

NASA Astrophysics Data System (ADS)

Rayner-Canham, Geoffrey

2004-03-01

During those early halcyon days of the study of radioactivity, one young Canadian woman, Harriet Brooks, joined Ernest Rutherford's group as his first research student. Later, she joined J.J. Thomson's group in Cambridge and, finally, Marie Curie's group in Paris. During her short research career, she made several important contributions to science. She investigated the nature of 'emanation' from radium; discovered that radioactive substances could undergo successive decay; and first reported the recoil of the radioactive atom. Much of this research was published under her name alone though Rutherford made extensive reference to her discoveries in his Bakerian lecture of 1904. Brooks life is of interest not only in what she accomplished, but also in the challenges she faced as a pioneering woman scientist in the early part of the twentieth century. In the presentation we will blend the account of her life and work with the societal context. This work was accomplished jointly with Marelene F. Rayner-Canham.

Mitigating the Cultural Challenges of SOF/Conventional Force Interdependence

DTIC Science & Technology

2013-03-01

Cultural Challenges of SOF / Conventional Force Interdependence 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S...January 16, 2013. 31 Daniel French , “Integration of General Purpose Forces and Army Special Operations,” 1. 32 Edward L. Cardon , “Recognizing

Business involvement in science education

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winter, P.

1995-12-31

Science and math education in grades K through 12 directly affects America`s ability to meet tomorrow`s challenges. If America is to stay competitive in the world, we will need highly qualified scientists and engineers in industry and government and at universities. Jobs of the future will require greater technical and mathematical literacy than jobs of the past. Our goal is both to improve the quality of science education and to encourage more students to pursue science careers. General Atomics, a privately held research and development company, has joined the growing list of businesses that are committed to helping educators preparemore » students to meet these challenges.« less

Coatings on Earth and Beyond

NASA Technical Reports Server (NTRS)

Calle, Luz Marina

2015-01-01

Coatings have always been spearheading technology developments, as they have to function faultlessly in very demanding conditions. Coatings for use on spacecraft and launch vehicle launch environments offer technological challenges beyond the normal boundaries of most coatings service environments. Among all the space environments, the most treacherous is that of the launch environment. To ensure the success of space missions, NASA must rely on the best materials available, and that very much includes coatings. What kind of technology can meet those challenges? What is expected of coatings manufacturers wanting to join the space race? What insights can the whole industry gain? Luz Marina Calle will present an overview of corrosion protective coatings at NASA.

A visual surveillance system for person re-identification

NASA Astrophysics Data System (ADS)

El-Alfy, Hazem; Muramatsu, Daigo; Teranishi, Yuuichi; Nishinaga, Nozomu; Makihara, Yasushi; Yagi, Yasushi

2017-03-01

We attempt the problem of autonomous surveillance for person re-identification. This is an active research area, where most recent work focuses on the open challenges of re-identification, independently of prerequisites of detection and tracking. In this paper, we are interested in designing a complete surveillance system, joining all the pieces of the puzzle together. We start by collecting our own dataset from multiple cameras. Then, we automate the process of detection and tracking of human subjects in the scenes, followed by performing the re-identification task. We evaluate the recognition performance of our system, report its strengths, discuss open challenges and suggest ways to address them.

Career Advancement of Indian Women in Management: Literature Review of the Challenges and Conceptualising Stakeholders Approach Critical for Women's Development

ERIC Educational Resources Information Center

Khera, Shikha N.; Malik, Sahil

2016-01-01

Women talent in India is available in plenty and are joining the workforce in numbers. The bone of contention remains that a handful of them are able to get elevated to senior positions. Even then they are offered discounted roles, allowing only male executives to compete for top management positions. The paper attempts to identify and do an…

IT Labs Proof-of-Concept Project: Technical Data Interoperability (TDI) Pathfinder Via Emerging Standards

NASA Technical Reports Server (NTRS)

Conroy, Mike; Gill, Paul; Ingalls, John; Bengtsson, Kjell

2014-01-01

No known system is in place to allow NASA technical data interoperability throughout the whole life cycle. Life Cycle Cost (LCC) will be higher on many developing programs if action isn't taken soon to join disparate systems efficiently. Disparate technical data also increases safety risks from poorly integrated elements. NASA requires interoperability and industry standards, but breaking legacy ways is a challenge.

2018 NASA Day of Remembrance

NASA Image and Video Library

2018-01-25

Guests place flowers near the Space Mirror Memorial at the Kennedy Space Center Visitor Complex. The names of fallen astronauts from Apollo 1, Challenger and Columbia, as well as the astronauts who perished in training and commercial airplane accidents are emblazoned on the monument. During the annual Day of Remembrance, spaceport employees and guests join others throughout NASA honoring the contributions of astronauts who have perished in the conquest of space.

2018 NASA Day of Remembrance

NASA Image and Video Library

2018-01-25

Flowers are placed near the Space Mirror Memorial at the Kennedy Space Center Visitor Complex. The names of fallen astronauts from Apollo 1, Challenger and Columbia, as well as the astronauts who perished in training and commercial airplane accidents are emblazoned on the monument. During the annual Day of Remembrance, spaceport employees and guests join others throughout NASA honoring the contributions of astronauts who have perished in the conquest of space.

Joining up health and planning: how Joint Strategic Needs Assessment (JSNA) can inform health and wellbeing strategies and spatial planning.

PubMed

Tomlinson, Paul; Hewitt, Stephen; Blackshaw, Neil

2013-09-01

There has been a welcome joining up of the rhetoric around health, the environment and land use or spatial planning in both the English public health white paper and the National Planning Policy Framework. However, this paper highlights a real concern that this is not being followed through into practical guidance needed by local authorities (LAs), health bodies and developers about how to deliver this at the local level. The role of Joint Strategic Needs Assessments (JSNAs) and Health and Wellbeing Strategies (HWSs) have the potential to provide a strong basis for integrated local policies for health improvement, to address the wider determinants of health and to reduce inequities. However, the draft JSNA guidance from the Department of Health falls short of providing a robust, comprehensive and practical guide to meeting these very significant challenges. The paper identifies some examples of good practice. It recommends that action should be taken to raise the standards of all JSNAs to meet the new challenges and that HWSs should be aligned spatially and temporally with local plans and other LA strategies. HWSs should also identify spatially targeted interventions that can be delivered through spatial planning or transport planning. Steps need to be taken to ensure that district councils are brought into the process.

The effect of adult aggression on habitat selection by settlers of two coral-dwelling damselfishes.

PubMed

Ben-Tzvi, Ofer; Kiflawi, Moshe; Polak, Omer; Abelson, Avigdor

2009-01-01

Coral-reef fishes experience a major challenge when facing settlement in a multi-threat environment, within which, using settlement cues, they need to select a suitable site. Studies in laboratories and artificial setups have shown that the presence of conspecific adults often serves as a positive settlement cue, whose value is explained by the increased survival of juveniles in an already proven fit environment. However, settlement in already inhabited corals may expose the recruits to adult aggression. Daily observations and manipulation experiments were used in the present study, which was conducted in the natural reef. We revealed differential strategies of settlers, which do not necessarily join conspecific adults. Dascyllus aruanus prefer to settle near (not with) their aggressive adults, and to join them only after gaining in size; whereas Dascyllus marginatus settlers in densely populated reefs settle independently of their adult distribution. Our results present different solutions to the challenges faced by fish recruits while selecting their microhabitat, and emphasize the complexity of habitat selection by the naïve settlers. Although laboratory experiments are important to the understanding of fish habitat selection, further studies in natural habitats are essential in order to elucidate the actual patterns of settlement and habitat selection, which are crucial for the survival of coral-reef fish populations.

Advantages and challenges of dissimilar materials in automotive lightweight construction

NASA Astrophysics Data System (ADS)

Weberpals, Jan-Philipp; Schmidt, Philipp A.; Böhm, Daniel; Müller, Steffen

2015-03-01

The core of future automotive lightweight materials is the joining technology of various material mixes. The type of joining will be essential, particularly in electrified propulsion systems, especially as an improved electrical energy transmission leads to a higher total efficiency of the vehicle. The most evident parts to start the optimization process are the traction battery, the electrical performance modules and the engines. Consequently aluminum plays a very central role for lightweight construction applications. However, the physical-technical requirements of components often require the combination with other materials. Thus the joining of mixed material connections is an essential key technology for many of the current developments, for example in the areas E-Mobility, solar energy and lightweight construction. Due to these advantages mixed material joints are already established in the automotive industry and laser beam remote welding is now a focus technology for mixed material connections. The secret of the laser welding process with mixed materials lies within the different areas of the melting phase diagram depending on the mixing ratio and the cooling down rate. According to that areas with unwanted, prim, intermetallic phases arise in the fusion zone. Therefore, laser welding of mixed material connections can currently only be used with additional filler in the automotive industry.

Precise Sequential DNA Ligation on A Solid Substrate: Solid-Based Rapid Sequential Ligation of Multiple DNA Molecules

PubMed Central

Takita, Eiji; Kohda, Katsunori; Tomatsu, Hajime; Hanano, Shigeru; Moriya, Kanami; Hosouchi, Tsutomu; Sakurai, Nozomu; Suzuki, Hideyuki; Shinmyo, Atsuhiko; Shibata, Daisuke

2013-01-01

Ligation, the joining of DNA fragments, is a fundamental procedure in molecular cloning and is indispensable to the production of genetically modified organisms that can be used for basic research, the applied biosciences, or both. Given that many genes cooperate in various pathways, incorporating multiple gene cassettes in tandem in a transgenic DNA construct for the purpose of genetic modification is often necessary when generating organisms that produce multiple foreign gene products. Here, we describe a novel method, designated PRESSO (precise sequential DNA ligation on a solid substrate), for the tandem ligation of multiple DNA fragments. We amplified donor DNA fragments with non-palindromic ends, and ligated the fragment to acceptor DNA fragments on solid beads. After the final donor DNA fragments, which included vector sequences, were joined to the construct that contained the array of fragments, the ligation product (the construct) was thereby released from the beads via digestion with a rare-cut meganuclease; the freed linear construct was circularized via an intra-molecular ligation. PRESSO allowed us to rapidly and efficiently join multiple genes in an optimized order and orientation. This method can overcome many technical challenges in functional genomics during the post-sequencing generation. PMID:23897972

Torsional Shear Strength Tests for Glass-Ceramic Joined Silicon Carbide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferraris, Monica; Ventrella, Andrea; Salvo, Milena

2014-03-17

A torsion test on hour-glass-shaped samples with a full joined or a ring-shaped joined area was chosen in this study to measure shear strength of glass-ceramic joined silicon carbide. Shear strength of about 100 MPa was measured for full joined SiC with fracture completely inside their joined area. Attempts to obtain this shear strength with a ring-shaped joined area failed due to mixed mode fractures. However, full joined and ring-shaped steel hour-glasses joined by a glass-ceramic gave the same shear strength, thus suggesting that this test measures shear strength of joined components only when their fracture is completely inside theirmore » joined area.« less

Evaluating the Upset Protrusion Joining (UPJ) Method to Join Magnesium Castings to Dissimilar Metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Logan, Stephen

2016-02-24

This presentation discusses advantages and best practices for incorporating magnesium in automotive component applications to achieve substantial mass reduction, as well as some of the key challenges with respect to joining, coating, and galvanic corrosion, before providing an introduction and status update of the U.S. Department of Energy and Department of Defense jointly sponsored Upset Protrusion Joining (UPJ) process development and evaluation project. This update includes sharing performance results of a benchmark evaluation of the self-pierce riveting (SPR) process for joining dissimilar magnesium (Mg) to aluminum (Al) materials in four unique coating configurations before introducing the UPJ concept and comparingmore » performance results of the joints made with the UPJ process to those made with the SPR process. Key results presented include: The benchmark SPR process can produce good joints in the MgAM60B-Al 6013 joint configuration with minimal cracking in the Mg coupons if the rivet is inserted from the Mg side into the Al side; Numerous bare Mg to bare Al joints made with the SPR process separated after only 6-wks of accelerated corrosion testing due to fracture of the rivet as a result of hydrogen embrittlement; For the same joint configurations, UPJ demonstrated substantially higher pre-corrosion joint strengths and post-corrosion joint strengths, primarily because of the larger diameter protrusion compared to smaller SPR rivet diameter and reduced degradation due to accelerated corrosion exposure; As with the SPR process, numerous bare Mg to bare Al joints made with the UPJ process also separated after 6-wks of accelerated corrosion testing, but unlike the SPR experience, the UPJ joints experienced degradation of the boss and head because of galvanic corrosion of the Mg casting, not hydrogen embrittlement of the steel rivet; In the configuration where both the Mg and Al were pretreated with Alodine 5200 prior to joining and the complete assembly was powder-coated afterwards, the UPJ process showed substantial improvement in corrosion performance compared to SPR where many SPR joints had separated after only 6-wks of exposure, but none of the UPJ joints had separated even after 8-wis; and In the cases where the Al panel was coated prior to joining to the pretreated Mg coupons, neither the SPR or UPJ joints showed any joint separation or substantial joint performance degradation even after 12-wks of accelerated corrosion exposure.« less

The quest for novel modes of excitation in exotic nuclei

NASA Astrophysics Data System (ADS)

Paar, N.

2010-06-01

This paper provides an insight into several open problems in the quest for novel modes of excitation in nuclei with isospin asymmetry, deformation and finite-temperature characteristics in stellar environments. Major unsolved problems include the nature of pygmy dipole resonances, the quest for various multipole and spin-isospin excitations both in neutron-rich and proton drip-line nuclei mainly driven by loosely bound nucleons, excitations in unstable deformed nuclei and evolution of their properties with the shape phase transition. Exotic modes of excitation in nuclei at finite temperatures characteristic of supernova evolution present open problems with a possible impact in modeling astrophysically relevant weak interaction rates. All these issues challenge self-consistent many-body theory frameworks at the frontiers of on-going research, including nuclear energy density functionals, both phenomenological and constrained by the strong interaction physics of QCD, models based on low-momentum two-nucleon interaction Vlow-k and correlated realistic nucleon-nucleon interaction VUCOM, supplemented by three-body force, as well as two-nucleon and three-nucleon interactions derived from the chiral effective field theory. Joined theoretical and experimental efforts, including research with radioactive isotope beams, are needed to provide insight into dynamical properties of nuclei away from the valley of stability, involving the interplay of isospin asymmetry, deformation and finite temperature.

Transforming Civil Engineering. Air Force Civil Engineer, Volume 15, Number 1, 2007

DTIC Science & Technology

2007-01-01

challenges is transformation coupled with a reduction of forces; it will take center stage for all of us,” said CMSgt Quattrone. “We can’t say change is...so far the sub- ject of several questions. As the day went on, training came up quite a few times more. “We realize it’s a challenge sometimes to...advanced training classes, forcing bases to train more specialty-specific skills at home station. It’s become a challenge for our senior officers and

Friction Hydro-Pillar Processing of a High Carbon Steel: Joint Structure and Properties

NASA Astrophysics Data System (ADS)

Kanan, Luis Fernando; Vicharapu, Buchibabu; Bueno, Antonio Fernando Burkert; Clarke, Thomas; De, Amitava

2018-04-01

A coupled experimental and theoretical study is reported here on friction hydro-pillar processing of AISI 4140 steel, which is a novel solid-state joining technique to repair and fill crack holes in thick-walled components by an external stud. The stud is rotated and forced to fill a crack hole by plastic flow. During the process, frictional heating occurs along the interface of the stud and the wall of crack hole leading to thermal softening of the stud that eases its plastic deformation. The effect of the stud force, its rotational speed and the total processing time on the rate of heat generation and resulting transient temperature field is therefore examined to correlate the processing variables with the joint structure and properties in a systematic and quantitative manner, which is currently scarce in the published literature. The results show that a gentler stud force rate and greater processing time can promote proper filling of the crack hole and facilitate a defect-free joint between the stud and original component.

Sliding states of a soft-colloid cluster crystal: Cluster versus single-particle hopping

NASA Astrophysics Data System (ADS)

Rossini, Mirko; Consonni, Lorenzo; Stenco, Andrea; Reatto, Luciano; Manini, Nicola

2018-05-01

We study a two-dimensional model for interacting colloidal particles which displays spontaneous clustering. Within this model we investigate the competition between the pinning to a periodic corrugation potential and a sideways constant pulling force which would promote a sliding state. For a few sample particle densities and amplitudes of the periodic corrugation potential we investigate the depinning from the statically pinned to the dynamically sliding regime. This sliding state exhibits the competition between a dynamics where entire clusters are pulled from a minimum to the next and a dynamics where single colloids or smaller groups leave a cluster and move across the corrugation energy barrier to join the next cluster downstream in the force direction. Both kinds of sliding states can occur either coherently across the entire sample or asynchronously: the two regimes result in different average mobilities. Finite temperature tends to destroy separate sliding regimes, generating a smoother dependence of the mobility on the driving force.

Advances in Solid State Joining of Haynes 230 High Temperature Alloy

NASA Technical Reports Server (NTRS)

Ding, R. Jeffrey; Schneider, Judy; Walker, Bryant

2010-01-01

The J-2X engine is being designed for NASA s new class of crew and launch vehicles, the Ares I and Ares V. The J-2X is a LOX/Hydrogen upper stage engine with 294,000 lbs of thrust and a minimum Isp of 448 seconds. As part of the design criteria to meet the performance requirements a large film-cooled nozzle extension is being designed to further expand the hot gases and increases the specific impulse. The nozzle extension is designed using Haynes 230, a nickel-chromium-tungsten-molybdenum superalloy. The alloy was selected for its high strength at elevated temperatures and resistance to hydrogen embrittlement. The nozzle extension is manufactured from Haynes 230 plate spun-forged to form the contour and chemically-milled pockets for weight reduction. Currently fusion welding is being evaluated for joining the panels which are then mechanically etched and thinned to required dimensions for the nozzle extension blank. This blank is then spun formed into the parabolic geometry required for the nozzle. After forming the nozzle extension, weight reduction pockets are chemically milled into the nozzle. Fusion welding of Haynes results in columnar grains which are prone to hot cracking during forming processes. This restricts the ability to use spin forging to produce the nozzle contour. Solid state joining processes are being pursued as an alternative process to produce a structure more amenable to spin forming. Solid state processes have been shown to produce a refined grain structure within the joint regions as illustrated in Figure 1. Solid state joining processes include friction stir welding (FSW) and a patented modification termed thermal stir welding (TSW). The configuration of TSWing utilizes an induction coil to preheat the material minimizing the burden on the weld tool extending its life. This provides the ability to precisely select and control the temperature. The work presented in this presentation investigates the feasibility of joining the Haynes 230 alloy using the solid state welding processes of FSW and TSW. Process descriptions and attributes of each weld process will be presented. Weld process set-up and welding techniques will be discussed leading to the challenges experienced in joining the superalloy. Mechanical property data will also be presented.

Cut and join operator ring in tensor models

NASA Astrophysics Data System (ADS)

Itoyama, H.; Mironov, A.; Morozov, A.

2018-07-01

Recent advancement of rainbow tensor models based on their superintegrability (manifesting itself as the existence of an explicit expression for a generic Gaussian correlator) has allowed us to bypass the long-standing problem seen as the lack of eigenvalue/determinant representation needed to establish the KP/Toda integrability. As the mandatory next step, we discuss in this paper how to provide an adequate designation to each of the connected gauge-invariant operators that form a double coset, which is required to cleverly formulate a tree-algebra generalization of the Virasoro constraints. This problem goes beyond the enumeration problem per se tied to the permutation group, forcing us to introduce a few gauge fixing procedures to the coset. We point out that the permutation-based labeling, which has proven to be relevant for the Gaussian averages is, via interesting complexity, related to the one based on the keystone trees, whose algebra will provide the tensor counterpart of the Virasoro algebra for matrix models. Moreover, our simple analysis reveals the existence of nontrivial kernels and co-kernels for the cut operation and for the join operation respectively that prevent a straightforward construction of the non-perturbative RG-complete partition function and the identification of truly independent time variables. We demonstrate these problems by the simplest non-trivial Aristotelian RGB model with one complex rank-3 tensor, studying its ring of gauge-invariant operators, generated by the keystone triple with the help of four operations: addition, multiplication, cut and join.

Supriya Jindal visits school

NASA Technical Reports Server (NTRS)

2009-01-01

Louisiana First Lady Supriya Jindal (left) speaks to teachers and students at A.P. Tureaud Elementary School in New Orleans during a March 19 visit. At the school, Jindal was joined by retired NASA astronaut Sally Ride, the first American woman in space. Ride was a crew member on space shuttle Challenger during its STS-7 mission in 1983. She also was a crew member of space shuttle discovery on the STS-41 mission in 1984.

2018 NASA Day of Remembrance

NASA Image and Video Library

2018-01-25

Following this year's Day of Remembrance ceremony at the Kennedy Space Center Visitor Complex, guests pick up flowers to place at the Space Mirror Memorial. The names of fallen astronauts from Apollo 1, Challenger and Columbia, as well as the astronauts who perished in training and commercial airplane accidents are emblazoned on the monument. Each year spaceport employees and guests join others throughout NASA honoring the contributions of astronauts who have perished in the conquest of space.

The pediatrician's role in supporting adoptive families.

PubMed

Jones, Veronnie F; Schulte, Elaine E

2012-10-01

Each year, more children join families through adoption. Pediatricians have an important role in assisting adoptive families in the various challenges they may face with respect to adoption. The acceptance of the differences between families formed through birth and those formed through adoption is essential in promoting positive emotional growth within the family. It is important for pediatricians to be aware of the adoptive parents' need to be supported in their communication with their adopted children.

Apparatus and method for performing microfluidic manipulations for chemical analysis and synthesis

DOEpatents

Ramsey, J. Michael

2000-01-01

A microchip laboratory system and method provide fluid manipulations for a variety of applications, including sample injection for microchip chemical separations. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis and electrochromatography are performed in channels formed in the substrate. Analytes are loaded into a four-way intersection of channels by electrokinetically pumping the analyte through the intersection, followed by switching of the potentials to force an analyte plug into the separation channel.

Apparatus and method for performing microfluidic manipulations for chemical analysis and synthesis

DOEpatents

Ramsey, J. Michael

2000-01-01

A microchip laboratory system and method proved fluid manipulations for a variety of applications, including sample injection for microchip chemical separations. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis and electrochromatography are performed in channels formed in the substrate. Analytes are loaded into a four-way intersection of channels by electrokinetically pumping the analyte through the intersection, followed by switching of the potentials to force an analyte plug into the separation channel.

Apparatus and method for performing microfluidic manipulations for chemical analysis and synthesis

DOEpatents

Ramsey, J. Michael

2002-01-01

A microchip laboratory system and method provide fluid manipulations for a variety of applications, including sample injection for microchip chemical separations. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis and electrochromatography are performed in channels formed in the substrate. Analytes are loaded into a four-way intersection of channels by electrokinetically pumping the analyte through the intersection, followed by switching of the potentials to force an analyte plug into the separation channel.

Apparatus and method for performing microfluidic manipulations for chemical analysis and synthesis

DOEpatents

Ramsey, J. Michael

1999-01-01

A microchip laboratory system and method provide fluid manipulations for a variety of applications, including sample injection for microchip chemical separations. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis and electrochromatography are performed in channels formed in the substrate. Analytes are loaded into a four-way intersection of channels by electrokinetically pumping the analyte through the intersection, followed by switching of the potentials to force an analyte plug into the separation channel.

Stolen Vehicles for Export: A Major Concern for Domestic and International Security

DTIC Science & Technology

2018-03-01

Terrorists and Organized Crime Join Forces,” New York Times, May 24, 2005. 5 Bryan Bender, “Stolen U.S. Vehicles End up as Bombs in Iraq, FBI Says,” New...also trafficked to finance other crimes. They can also be used as bomb carriers or in the perpetration of other crimes.31 In an effort to address...as VBIEDs in terrorist activities, but it is believed to be in the dozens.67 “A car bomb is the absolute favorite delivery methods of terrorists

Apparatus and method for performing microfluidic manipulations for chemical analysis and synthesis

DOEpatents

Ramsey, J.M.

1999-01-12

A microchip laboratory system and method provide fluid manipulations for a variety of applications, including sample injection for microchip chemical separations. The microchip is fabricated using standard photolithographic procedures and chemical wet etching, with the substrate and cover plate joined using direct bonding. Capillary electrophoresis and electrochromatography are performed in channels formed in the substrate. Analytes are loaded into a four-way intersection of channels by electrokinetically pumping the analyte through the intersection, followed by switching of the potentials to force an analyte plug into the separation channel. 46 figs.

ASCAN Helms simulates parachute jump during VAFB training exercises

NASA Image and Video Library

1990-09-17

S90-48372 (29-31 July 1990) --- Mission specialist astronaut candidate Susan J. Helms simulates a parachute jump during a survival training course at Vance Air Force Base. She is one of 23 astronaut candidates from the Johnson Space Center who have joined military personnel for the special three-day training course. The course is designed to prepare the trainees for proper survival measures to take in the event of an emergency aboard the T-38 jet trainer aircraft they will frequently use once they become full-fledged astronauts.

How Female Officers’ Performance in Non-Traditional U.S. Navy Shipboard Jobs Compares to Male Officers’ Performance

DTIC Science & Technology

1988-12-01

SAS Institute Inc. 14. Kanter, Rosabeth M., Men and Women of the Corporation, Basic Books, Inc., 1977. 15. Snyder, Mark, " Self -Fulfilling Stereotypes ...this thesis are those of the author and do not reflect the official policy or position of the Department of Defense or the U.S. Government. 17 Cosati... reflection upon the courageous manhood of the country to pass a law inviting women to Join the armed forces in order to win a battle. Take the women into

Kepler Media Briefing

NASA Image and Video Library

2009-02-19

Jon Morse, Director, Astrophysics Division, at NASA Headquarters, left, talks about the Kepler mission during a media briefing, Thursday, Feb. 19, 2008, at NASA Headquarters in Washington. Morse was joined at the briefing by William Borucki, principal investigator for Kepler Science at Ames Research Center, second left, Jim Fanson, Kepler Project Manager at the Jet Propulsion Laboratory and Debra Fischer, professor of Astronomy at San Francisco State University, right. Kepler is scheduled to launch on March 5, 2009 from Cape Canaveral Air Force Station, Fla. aboard a Delta II rocket. Photo Credit: (NASA/Paul. E. Alers)

Multi-Technique Study of Ionospheric Structures Causing Degradation in Trans-Ionospheric Communications Systems.

DTIC Science & Technology

1987-04-20

NASA . Dr. Basi was a member of the Guest Investigator Team on the NASA Atmosphere Explorer Program and is currently a member of the Dynamics Explorer...Electric Com- pany in Lynn. MA. At this point he joined the Geomagnctism Branch at the Air Force Cam- Ilerbert E. Whitney. photograph and biography not...crgs ENERGYtlb*V) (cm 2 s)- ’ arc observed. The gaps in between the precipitation I-if; 3 Lt-. .i .etrum obtained ai 14O1.45 UT shoting nil acl- regions