Preliminary Design and Analysis of an In-plane PRSEUS Joint

NASA Technical Reports Server (NTRS)

Lovejoy, Andrew E.; Poplawski, Steven

2013-01-01

As part of the National Aeronautics and Space Administration's (NASA's) Environmentally Responsible Aviation (ERA) program, the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) has been designed, developed and tested. However, PRSEUS development efforts to date have only addressed joints required to transfer bending moments between PRSEUS panels. Development of in-plane joints for the PRSEUS concept is necessary to facilitate in-plane transfer of load from PRSEUS panels to an adjacent structure, such as from a wing panel into a fuselage. This paper presents preliminary design and analysis of an in-plane PRSEUS joint for connecting PRSEUS panels at the termination of the rod-stiffened stringers. Design requirements are provided, the PRSEUS blade joint concept is presented, and preliminary design changes and analyses are carried out to examine the feasibility of the proposed in-plane PRSEUS blade joint. The study conducted herein focuses mainly on the PRSEUS structure on one side of the joint. In particular, the design requirements for the rod shear stress and bolt bearing stress are examined. A PRSEUS blade joint design was developed that demonstrates the feasibility of this in-plane PRSEUS joint concept to terminate the rod-stiffened stringers. The presented design only demonstrates feasibility, therefore, some areas of refinement are presented that would lead to a more optimum and realistic design.

Teaching Engineering Ethics to PhD Students: A Berkeley-Delft Initiative : Commentary on "Ethics Across the Curriculum: Prospects for Broader (and Deeper) Teaching and Learning in Research and Engineering Ethics".

PubMed

Taebi, Behnam; Kastenberg, William E

2016-07-13

A joint effort by the University of California at Berkeley and Delft University of Technology to develop a graduate engineering ethics course for PhD students encountered two types of challenges: academic and institutional. Academically, long-term collaborative research efforts between engineering and philosophy faculty members might be needed before successful engineering ethics courses can be initiated; the teaching of ethics to engineering graduate students and collaborative research need to go hand-in-hand. Institutionally, both bottom-up approaches at the level of the faculty and as a joint research and teaching effort, and top-down approaches that include recognition by a University's administration and the top level of education management, are needed for successful and sustainable efforts to teach engineering ethics.

Development of a Geospatial Data-Sharing Method for Unmanned Vehicles Based on the Joint Architecture for Unmanned Systems (JAUS)

DTIC Science & Technology

2005-08-01

the Office of the Secretary of Defense chartered the Joint Architecture for Unmanned Ground Systems ( JAUGS ) Working Group to address these concerns...The JAUGS Working Group was tasked with developing an initial standard for interoperable unmanned ground systems. In 2002, the charter of the... JAUGS Working Group was 1 2 modified such that their efforts would extend to all unmanned systems, not only ground systems. The standard was

Risk management in international manned space program operations.

PubMed

Seastrom, J W; Peercy, R L; Johnson, G W; Sotnikov, B J; Brukhanov, N

2004-02-01

New, innovative joint safety policies and requirements were developed in support of the Shuttle/Mir program, which is the first phase of the International Space Station program. This work has resulted in a joint multinational analysis culminating in joint certification for mission readiness. For these planning and development efforts, each nation's risk programs and individual safety practices had to be integrated into a comprehensive and compatible system that reflects the joint nature of the endeavor. This paper highlights the major incremental steps involved in planning and program integration during development of the Shuttle/Mir program. It traces the transition from early development to operational status and highlights the valuable lessons learned that apply to the International Space Station program (Phase 2). Also examined are external and extraneous factors that affected mission operations and the corresponding solutions to ensure safe and effective Shuttle/Mir missions. c2003 Published by Elsevier Ltd.

Automated Chat Thread Analysis: Untangling the Web

DTIC Science & Technology

2010-01-01

delays, distractions, errant information sources, and overall cognitive effort. The most significant challenge to conducting an effective after...to emphasize. Thus, the goal is to develop a tool that serves as a cognitive aid to instructors developing an After-Action Review (AAR). Our...work is being done by the “ Cognitive Agent that Learns and Organizes” (CALO) project, a joint effort between SRI and Stanford University’s Center for

Great Expectations in the Joint Advanced Manufacturing Region

DTIC Science & Technology

2016-12-01

would be continuous experimentation and risk reduction prototyping. The entire manufacturing life cycle— design , testing, product development...on the back of a napkin, they decided to call their effort the Joint Advanced Manufacturing Region (JAMR) and manage it as an Integrated Product ... designed to support the continuous experimentation of advanced manufacturing tactics, tech- niques and procedures under actual operational or combat

Boom and chassis articulation joints

NASA Technical Reports Server (NTRS)

Murphy, Joel T., Jr.; Nguyen, Vien; Turner, Bonnie; Wheeler, Bobby; Williams, Kimberlyn

1992-01-01

The primary goal of our design project was to develop articulation joints for the chassis and boom of the proof-of-concept lunar vehicle. This is an ongoing project and the work of previous student groups was extensively reviewed. Some of the ideas generated are variations of past proposals. Although the project is funded by NASA/USRA, it is totally a student design effort.

A computational method for comparing the behavior and possible failure of prosthetic implants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nielsen, C.; Hollerbach, K.; Perfect, S.

1995-05-01

Prosthetic joint implants currently in use exhibit high Realistic computer modeling of prosthetic implants provides an opportunity for orthopedic biomechanics researchers and physicians to understand possible in vivo failure modes, without having to resort to lengthy and costly clinical trials. The research presented here is part of a larger effort to develop realistic models of implanted joint prostheses. The example used here is the thumb carpo-metacarpal (cmc) joint. The work, however, can be applied to any other human joints for which prosthetic implants have been designed. Preliminary results of prosthetic joint loading, without surrounding human tissue (i.e., simulating conditions undermore » which the prosthetic joint has not yet been implanted into the human joint), are presented, based on a three-dimensional, nonlinear finite element analysis of three different joint implant designs.« less

Estimations of relative effort during sit-to-stand increase when accounting for variations in maximum voluntary torque with joint angle and angular velocity.

PubMed

Bieryla, Kathleen A; Anderson, Dennis E; Madigan, Michael L

2009-02-01

The main purpose of this study was to compare three methods of determining relative effort during sit-to-stand (STS). Fourteen young (mean 19.6+/-SD 1.2 years old) and 17 older (61.7+/-5.5 years old) adults completed six STS trials at three speeds: slow, normal, and fast. Sagittal plane joint torques at the hip, knee, and ankle were calculated through inverse dynamics. Isometric and isokinetic maximum voluntary contractions (MVC) for the hip, knee, and ankle were collected and used for model parameters to predict the participant-specific maximum voluntary joint torque. Three different measures of relative effort were determined by normalizing STS joint torques to three different estimates of maximum voluntary torque. Relative effort at the hip, knee, and ankle were higher when accounting for variations in maximum voluntary torque with joint angle and angular velocity (hip=26.3+/-13.5%, knee=78.4+/-32.2%, ankle=27.9+/-14.1%) compared to methods which do not account for these variations (hip=23.5+/-11.7%, knee=51.7+/-15.0%, ankle=20.7+/-10.4%). At higher velocities, the difference in calculating relative effort with respect to isometric MVC or incorporating joint angle and angular velocity became more evident. Estimates of relative effort that account for the variations in maximum voluntary torque with joint angle and angular velocity may provide higher levels of accuracy compared to methods based on measurements of maximal isometric torques.

Criteria for Space-Based Sensor Applied to Bt Crop Monitoring

EPA Science Inventory

A joint agro-ecosystem research effort of NASA and USEPA has focused on the development of a decision support system designed to predict the development of insect pest resistance to transgenic toxins in maize. The use of NASA-developed remote sensing technologies that significant...

Continuously reinforced concrete pavement inventory

NASA Astrophysics Data System (ADS)

Halverson, A. D.; Hagen, M. G.

1982-09-01

A typical concrete pavement has expansion and contraction joints across and along the pavement surface. The joints allow the pavement to change in dimension with changes in temperature. A continuously reinforced concrete pavement (CRCP) does not have expansion or contraction joints. Random, closely spaced cracks are expected to develop naturally and allow for expansion and contraction due to temperature changes. The many random cracks eliminate expensive joint maintenance. This maintenance-free service life feature has not occurred in Minnesota. This CRCP inventory is a physical evaluation of the extent of corrosion on random sections of pavement. It is related to concurrent efforts which will evaluate CRCP rehabilitation techniques.

Joint FACET: the Canada-Netherlands initiative to study multisensor data fusion systems

NASA Astrophysics Data System (ADS)

Bosse, Eloi; Theil, Arne; Roy, Jean; Huizing, Albert G.; van Aartsen, Simon

1998-09-01

This paper presents the progress of a collaborative effort between Canada and The Netherlands in analyzing multi-sensor data fusion systems, e.g. for potential application to their respective frigates. In view of the overlapping interest in studying and comparing applicability and performance and advanced state-of-the-art Multi-Sensor Data FUsion (MSDF) techniques, the two research establishments involved have decided to join their efforts in the development of MSDF testbeds. This resulted in the so-called Joint-FACET, a highly modular and flexible series of applications that is capable of processing both real and synthetic input data. Joint-FACET allows the user to create and edit test scenarios with multiple ships, sensor and targets, generate realistic sensor outputs, and to process these outputs with a variety of MSDF algorithms. These MSDF algorithms can also be tested using typical experimental data collected during live military exercises.

Establishing Foundations for University/Professional Association Collaboration: The Profession Selection Process.

ERIC Educational Resources Information Center

Queeney, Donna S.; Melander, Jacqueline J.

The selection of professions that became part of the Continuing Professional Education Development Project, a joint research and development effort of The Pennsylvania State University and the Kellogg Foundation, is discussed. In addition to establishing collaboration between the university and the professions, the project sought to develop and…

Computerized Adaptive Testing Project: Objectives and Requirements.

DTIC Science & Technology

1982-07-01

developing a cqmputerlzed adaptive lwfb system ( CAT ). SiN 0102- LP. Old. "O AM"- S/M "of F.g~ smuuim ftmAYUSN 0 IM ~ A joint-service coordinated effort is In...progress to develop a computerized adaptive testing ( CAT ) system and to evaluate its potential for use in the Military Enlistment Processing Stations...lead laboratory for this effort. This report is intended to serve as a working paper documenting CAT system functional requirements and schedules. It

Joint Contributions of Negative Emotionality, Positive Emotionality, and Effortful Control on Depressive Symptoms in Youth.

PubMed

Van Beveren, Marie-Lotte; Mezulis, Amy; Wante, Laura; Braet, Caroline

2016-11-02

From a clinical developmental perspective, temperament has been shown to confer vulnerability to depression among youth. High negative emotionality (NE), low positive emotionality (PE), and low effortful control (EC) have repeatedly been independently associated with youth depressive symptoms. However, far less research has examined the joint contributions of NE, PE, and EC on such symptoms. The present study builds upon previous research by examining how NE, PE, and EC jointly predict change in depressive symptoms over time among 211 youngsters (7-14 years, M = 10.7, SD = 1.81) who participated in an 8-month prospective study. Self-reported temperament and symptoms were assessed at baseline; self-reported symptoms were measured again at follow-up. Results suggest that all 3 temperamental traits need to be considered jointly in predicting change in depressive symptoms. Furthermore, results provide further support for the "best two out of three" principle. Surprisingly, results reveal that high EC might be maladaptive in the context of high emotional reactivity. Last, results show that the combination of high NE and low EC could be a possible pathway to the development of symptoms. The current study clarified how NE, PE, and EC may jointly confer risk-or protection for developing depressive symptoms during adolescence. The results highlight the need of taking into account all three temperamental traits in order to provide a more nuanced understanding of the risk for developing depressive symptoms at an early stage, as well as to provide customized care targeting temperamental vulnerability in depressed youth.

Advancing Globally Integrated Logistics Effort 2017 Wargame Report

DTIC Science & Technology

2017-09-01

September 2017 Dr. M. Webster Ewell, Jr. Director, Integration and Gaming Team Advanced Technology and Systems Analysis REPORT...release: distribution unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT This report describes the execution and analysis of a logistics game created for...the Joint Staff J-4, Directorate for Logistics. The game , Advancing Globally Integrated Logistics Effort 2017 (AGILE 17), centered on developing a

SERVIR Regional Visualization and Monitoring System: A Brief Overview

NASA Technical Reports Server (NTRS)

Limaye, Ashutosh

2011-01-01

SERVIR is a joint USAID NASA effort, which uses remotely sensed data and products for societal benefit. SERVIR currently has three hubs, in Central America, East Africa and Himalaya. Science Applications, IT infrastructure and capacity building is central to SERVIR efforts. Collaborations are key. SERVIR is continuing to develop strong, working collaborations with government entities in the region, such as KMD.

Development of Displacement Gages Exposed to Solid Rocket Motor Internal Environments

NASA Technical Reports Server (NTRS)

Bolton, D. E.; Cook, D. J.

2003-01-01

The Space Shuttle Reusable Solid Rocket Motor (RSRM) has three non-vented segment-to-segment case field joints. These joints use an interference fit J-joint that is bonded at assembly with a Pressure Sensitive Adhesive (PSA) inboard of redundant O-ring seals. Full-scale motor and sub-scale test article experience has shown that the ability to preclude gas leakage past the J-joint is a function of PSA type, joint moisture from pre-assembly humidity exposure, and the magnitude of joint displacement during motor operation. To more accurately determine the axial displacements at the J-joints, two thermally durable displacement gages (one mechanical and one electrical) were designed and developed. The mechanical displacement gage concept was generated first as a non-electrical, self-contained gage to capture the maximum magnitude of the J-joint motion. When it became feasible, the electrical displacement gage concept was generated second as a real-time linear displacement gage. Both of these gages were refined in development testing that included hot internal solid rocket motor environments and simulated vibration environments. As a result of this gage development effort, joint motions have been measured in static fired RSRM J-joints where intentional venting was produced (Flight Support Motor #8, FSM-8) and nominal non-vented behavior occurred (FSM-9 and FSM-10). This data gives new insight into the nominal characteristics of the three case J-joint positions (forward, center and aft) and characteristics of some case J-joints that became vented during motor operation. The data supports previous structural model predictions. These gages will also be useful in evaluating J-joint motion differences in a five-segment Space Shuttle solid rocket motor.

The United States and Japan pursue a common agenda.

PubMed

Westley, S B

1996-10-01

In July 1993, the US and Japan formed the "Common Agenda for Cooperation in Global Perspective," an economic alliance to promote health and human development, respond to challenges to global stability, protect the global environment, advance science and technology, and foster exchanges for mutual understanding. A Global Issues Initiative (GII) has been created within this framework to support family planning, HIV and sexually transmitted disease prevention and control efforts, maternal and child health, primary health care, and women's empowerment. Participation in the GII has led Japan to more than double the technical assistance it provides and to broaden its geographic focus from Asia to the entire developing world. The US continues to fund population and health programs in more than 50 countries. The Common Agenda grew out of a US-Japan development assistance policy consultation dialogue known as the "Honolulu process," which sought ways to promote mutual understanding among US and Japanese development assistance personnel (through international internships) and nongovernmental organizations and to identify specific areas for joint or parallel development projects. Cooperative activities are underway in the Philippines, Indonesia, Bangladesh, India, Ghana, Peru, Guatemala, Mexico, and Jamaica. Joint project evaluations have also taken place in Zambia and Ghana. The Common Agenda's Children's Health Initiative has supported such initiatives as achieving child immunization in the Newly Independent States and joint efforts to eradicate polio and micronutrient disorders. The Women in Development initiative enhances girls' education and assists women engaged in small-scale enterprises. After initial difficulties in agreeing on joint strategies, the Common Agenda has been an "overwhelmingly positive" experience with the potential to meet critical challenges, because Japan and the US account for 40% of all development assistance worldwide.

Administrative Information Systems Plan for FY89

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-11-01

The Administrative Information Systems (AIS) Plan was developed to prioritize, track, and control the cost of AIS activities. This annually published plan, in conjunction with quarterly status reports, measures projected AIS activities and progress. The AIS Plan and quarterly reporting are administered jointly by the Director of Computing and an Organization 30 director. Priority development projects are clearly defined and closely managed efforts that consume significant resources. Directorate supplementals describe other AIS activity within each directorate, which may include: production support; technical support; development activity; and other AIS effort.

AOP Wiki: A new tool for developing and documenting adverse outcome pathways

EPA Science Inventory

An initial version of an IT system to support OECD AOP activities recently was completed through collaborative efforts and contributions of the European Commission's Joint Research Centre (EU JRC), the Office of Research and Development (ORD) of the United States Environmental Pr...

The Two-Year Post-Secondary College Student and Life Span Development.

ERIC Educational Resources Information Center

Morgan, Don A., Ed.

This monograph presents the papers and addresses of the Sixth Rochester Institute, an annual joint staff development effort of Rochester Community College and the University of Minnesota. W. Wesley Tennyson and Sharon Strom present a case for career development education to be used as a fulcrum to swing education further towards humanistic…

Regional Visualization and Monitoring System SERVIR: A Brief Overview, Water Resources Challenges and Approaches

NASA Technical Reports Server (NTRS)

Limaye, Ashutosh

2011-01-01

SERVIR is a joint USAID -- NASA effort, which uses remotely sensed data and products for societal benefit. SERVIR currently has three hubs, in Mesoamerica, East Africa and Himalaya. Collaborations are key. SE RVIR is continuing to develop strong, working collaborations with government entities, such as KMD. Science Applications, IT infrastructure and capacity building is central to SERVIR efforts.

THE NATIONAL ENVIRONMENTAL SPECIMEN BANK RESEARCH PROGRAM FOR SAMPLING, STORAGE, AND ANALYSIS

EPA Science Inventory

The work was performed under a joint NBS/EPA research program to develop state-of-the-art protocols for sampling, storage, and analysis of biological and environmental-type matrices. This report is a compliation of research papers and/or efforts describing developed or adopted pr...

The Computerized Adaptive Testing System Development Project.

ERIC Educational Resources Information Center

McBride, James R.; Sympson, J. B.

The Computerized Adaptive Testing (CAT) project is a joint Armed Services coordinated effort to develop and evaluate a system for automated, adaptive administration of the Armed Services Vocational Aptitude Battery (ASVAB). The CAT is a system for administering personnel tests that differs from conventional test administration in two major…

Collaborative engagement experiment (CEE)

NASA Astrophysics Data System (ADS)

Wade, Robert L.; Reames, Joseph M.

2005-05-01

Unmanned ground and air systems operating in collaboration have the potential to provide future Joint Forces a significant capability for operations in complex terrain. Ground and air collaborative engagements potentially offer force conservation, perform timely acquisition and dissemination of essential combat information, and can eliminate high value and time critical targets. These engagements can also add considerably to force survivability by reducing soldier and equipment exposure during critical operations. The Office of the Secretary of Defense, Joint Robotics Program (JRP) sponsored Collaborative Engagement Experiment (CEE) is a consolidation of separate Air Force, Army and Navy collaborative efforts to provide a Joint capability. The Air Force Research Laboratory (AFRL), Material and Manufacturing Directorate, Aerospace Expeditionary Force Division, Force Protection Branch (AFRLMLQF), The Army Aviation and Missile Research, Development and Engineering Center (AMRDEC) Joint Technology Center (JTC)/Systems Integration Laboratory (SIL), and the Space and Naval Warfare Systems Center-San Diego (SSC San Diego) are conducting technical research and proof of principle for an envisioned operational concept for extended range, three dimensional, collaborative operations between unmanned systems, with enhanced situational awareness for lethal operations in complex terrain. This program will assess information requirements and conduct experiments to identify and resolve technical risks for collaborative engagements using Unmanned Ground Vehicles (UGVs) and Unmanned Aerial Vehicles (UAVs). It will research, develop and physically integrate multiple unmanned systems and conduct live collaborative experiments. Modeling and Simulation systems will be upgraded to reflect engineering fidelity levels to greater understand technical challenges to operate as a team. This paper will provide an update of a multi-year program and will concentrate primarily on the JTC/SIL efforts. Other papers will outline in detail the Air Force and Navy portions of this effort.

Stress analysis of the space telescope focal plane structure joint

NASA Technical Reports Server (NTRS)

Foster, W. A., Jr.; Shoemaker, W. L.

1985-01-01

Two major efforts were begun concerning the Space Telescope focal plane structure joint. The 3-D solid finite element modeling of the bipod flexure plate was carried out. Conceptual models were developed for the load transfer through the three major bolts to the flexure plate. The flexure plate drawings were reconstructed using DADAM for the purpose of developing a file from which the coordinates of any point on the flexure plate could be determined and also to locate the attachment points of the various components which connect with the flexure plate. For modeling convenience the CADAM drawing of the flexure plate has been divided into several regions which will be subdivided into finite elements using MSGMESH, which is a finite element mesh generator available with MSC/NASTRAN. In addition to the CADAM work on the flexure plate, an effort was also begun to develop computer aided drawings of the peripheral beam which will be used to assist in modeling the connection between it and the flexure plate.

Explaining interindividual differences in toddlers' collaboration with unfamiliar peers: individual, dyadic, and social factors

PubMed Central

Schuhmacher, Nils; Kärtner, Joscha

2015-01-01

During their third year of life, toddlers become increasingly skillful at coordinating their actions with peer partners and they form joint commitments in collaborative situations. However, little effort has been made to explain interindividual differences in collaboration among toddlers. Therefore, we examined the relative influence of distinct individual, dyadic, and social factors on toddlers' collaborative activities (i.e., level of coordination and preference for joint activity) in joint problem-solving situations with unfamiliar peer partners (n = 23 dyads aged M = 35.7 months). We analyzed the dyadic nonindependent data with mixed models. Results indicated that mothers' expectations regarding their children's social behaviors significantly predicted toddlers' level of coordination. Furthermore, the models revealed that toddlers' positive mutual experiences with the unfamiliar partner assessed during an initial free play period (Phase 1) and their level of coordination in an obligatory collaboration task (Phase 2) promoted toddlers' preference for joint activity in a subsequent optional collaboration task (Phase 3). In contrast, children's mastery motivation and shyness conflicted with their collaborative efforts. We discuss the role of parents' socialization goals in toddlers' development toward becoming active collaborators and discuss possible mechanisms underlying the differences in toddlers' commitment to joint activities, namely social preferences and the trust in reliable cooperation partners. PMID:25983696

Synthesis of power plant outage schedules. Final technical report, April 1995-January 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, D.R.

This document provides a report on the creation of domain theories in the power plant outage domain. These were developed in conjunction with the creation of a demonstration system of advanced scheduling technology for the outage problem. In 1994 personnel from Rome Laboratory (RL), Kaman Science (KS), Kestrel Institute, and the Electric Power Research Institute (EPRI) began a joint project to develop scheduling tools for power plant outage activities. This report describes our support for this joint effort. The project uses KIDS (Kestrel Interactive Development System) to generate schedulers from formal specifications of the power plant domain outage activities.

U.S. Marine Corps Concepts & Programs 2009

DTIC Science & Technology

2009-01-01

war efforts in the CENTCOM AOR — that will demand balanced apportionment of limited re- sources . In this, the Marine Corps has identified four...Strike Fighter (JSF) Transition Plan 123 MV-22 Osprey Program 125 H-1 Upgrade (UH-1Y Huey/AH-1Z Cobra) 127 KC-130 Hercules 129 CH-53K Heavy Lift...leading joint-service development of our light, medium and heavy tactical wheeled vehicles for the joint force. The Expeditionary Fighting Vehicle (EFV

Envri Cluster - a Community-Driven Platform of European Environmental Researcher Infrastructures for Providing Common E-Solutions for Earth Science

NASA Astrophysics Data System (ADS)

Asmi, A.; Sorvari, S.; Kutsch, W. L.; Laj, P.

2017-12-01

European long-term environmental research infrastructures (often referred as ESFRI RIs) are the core facilities for providing services for scientists in their quest for understanding and predicting the complex Earth system and its functioning that requires long-term efforts to identify environmental changes (trends, thresholds and resilience, interactions and feedbacks). Many of the research infrastructures originally have been developed to respond to the needs of their specific research communities, however, it is clear that strong collaboration among research infrastructures is needed to serve the trans-boundary research requires exploring scientific questions at the intersection of different scientific fields, conducting joint research projects and developing concepts, devices, and methods that can be used to integrate knowledge. European Environmental research infrastructures have already been successfully worked together for many years and have established a cluster - ENVRI cluster - for their collaborative work. ENVRI cluster act as a collaborative platform where the RIs can jointly agree on the common solutions for their operations, draft strategies and policies and share best practices and knowledge. Supporting project for the ENVRI cluster, ENVRIplus project, brings together 21 European research infrastructures and infrastructure networks to work on joint technical solutions, data interoperability, access management, training, strategies and dissemination efforts. ENVRI cluster act as one stop shop for multidisciplinary RI users, other collaborative initiatives, projects and programmes and coordinates and implement jointly agreed RI strategies.

General Motors Partners with NREL to Reduce Automotive Fuel Cell Costs |

Science.gov Websites

Reduce Automotive Fuel Cell Costs General Motors (GM) is partnering with NREL on a multiyear , multimillion-dollar joint research and development effort to lower the cost of automotive fuel cell stacks

Results of the Clarus Regional Demonstrations : Evaluation of Enhanced Road Weather Forecasting

DOT National Transportation Integrated Search

2012-01-01

The Clarus Initiative is a research effort of the U.S. Department of Transportation Intelligent Transportation Systems Joint Program Office and the Federal Highway Administrations Road Weather Management Program to develop and demonstrate an integ...

Opportunities for the privatization of Virginia's rest areas and welcome centers.

DOT National Transportation Integrated Search

1991-01-01

The report presents the findings of a study that investigated the opportunities for the future development, expansion, and operation of Virginia's rest areas and welcome centers through joint efforts of the Virginia Department of Transportation (VDOT...

CANUSA mid-program report

Treesearch

David G. Grimble

1981-01-01

The Canada-United States Spruce Budworms Program (CANUSA) is a 6-year joint effort by the Department of the Environment, Canada, and the USDA Forest Service to develop methods for controlling spruce budworms in the Eastern and Western United States and in Canada.

Overview 1993: Computational applications

NASA Technical Reports Server (NTRS)

Benek, John A.

1993-01-01

Computational applications include projects that apply or develop computationally intensive computer programs. Such programs typically require supercomputers to obtain solutions in a timely fashion. This report describes two CSTAR projects involving Computational Fluid Dynamics (CFD) technology. The first, the Parallel Processing Initiative, is a joint development effort and the second, the Chimera Technology Development, is a transfer of government developed technology to American industry.

Forebody/Inlet of the Joint Strike Fighter Tested at Low Speeds

NASA Technical Reports Server (NTRS)

Johns, Albert L.

1998-01-01

As part of a national cooperative effort to develop a multinational fighter aircraft, a model of a Joint Strike Fighter concept was tested in several NASA Lewis Research Center wind tunnels at low speeds over a range of headwind velocities and model attitudes. This Joint Strike Fighter concept, which is scheduled to go into production in 2005, will greatly improve the range, capability, maneuverability, and survivability of fighter aircraft, and the production program could ultimately be worth $100 billion. The test program was a team effort between Lewis and Lockheed Martin Tactical Aircraft Systems. Testing was completed in September 1997, several weeks ahead of schedule, allowing Lockheed additional time to review the results and analysis data before the next test and resulting in significant cost savings for Lockheed. Several major milestones related to dynamic and steady-state data acquisition and overall model performance were reached during this model test. Results from this program will contribute to both the concept demonstration phase and the production aircraft.

Transient liquid phase diffusion bonding of Udimet 720 for Stirling power converter applications

NASA Technical Reports Server (NTRS)

Mittendorf, Donald L.; Baggenstoss, William G.

1992-01-01

Udimet 720 has been selected for use on Stirling power converters for space applications. Because Udimet 720 is generally considered susceptible to strain age cracking if traditional fusion welding is used, other joining methods are being considered. A process for transient liquid phase diffusion bonding of Udimet 720 has been theoretically developed in an effort to eliminate the strain age crack concern. This development has taken into account such variables as final grain size, joint homogenization, joint efficiency related to bonding aid material, bonding aid material application method, and thermal cycle.

NASA safety program activities in support of the Space Exploration Initiatives Nuclear Propulsion program

NASA Technical Reports Server (NTRS)

Sawyer, J. C., Jr.

1993-01-01

The activities of the joint NASA/DOE/DOD Nuclear Propulsion Program Technical Panels have been used as the basis for the current development of safety policies and requirements for the Space Exploration Initiatives (SEI) Nuclear Propulsion Technology development program. The Safety Division of the NASA Office of Safety and Mission Quality has initiated efforts to develop policies for the safe use of nuclear propulsion in space through involvement in the joint agency Nuclear Safety Policy Working Group (NSPWG), encouraged expansion of the initial policy development into proposed programmatic requirements, and suggested further expansion into the overall risk assessment and risk management process for the NASA Exploration Program. Similar efforts are underway within the Department of Energy to ensure the safe development and testing of nuclear propulsion systems on Earth. This paper describes the NASA safety policy related to requirements for the design of systems that may operate where Earth re-entry is a possibility. The expected plan of action is to support and oversee activities related to the technology development of nuclear propulsion in space, and support the overall safety and risk management program being developed for the NASA Exploration Program.

The SCORE System. Final Report. 1994-1995.

ERIC Educational Resources Information Center

Collin County Community Coll., McKinney, TX.

Project SCORE (School and Community Offering Resources for Employment) was undertaken by Collin County Community College in Texas to develop a system to help McKinney High School students move with confidence from school to work and further education. The program, which was developed through the joint efforts of school and business/industry…

Schooling as a Knowledge System: Lessons from Cramim Experimental School

ERIC Educational Resources Information Center

Chen, David

2010-01-01

This article describes an experiment utilizing a research and development strategy to design and implement an innovative school for the future. The development of Cramim Elementary School was a joint effort of researchers from Tel-Aviv University and the staff of the school. The design stage involved constructing a new theoretical framework that…

Scaling NASA Applications to 1024 CPUs on Origin 3K

NASA Technical Reports Server (NTRS)

Taft, Jim

2002-01-01

The long and highly successful joint SGI-NASA research effort in ever larger SSI systems was to a large degree the result of the successful development of the MLP scalable parallel programming paradigm developed at ARC: 1) MLP scaling in real production codes justified ever larger systems at NAS; 2) MLP scaling on 256p Origin 2000 gave SGl impetus to productize 256p; 3) MLP scaling on 512 gave SGI courage to build 1024p O3K; and 4) History of MLP success resulted in IBM Star Cluster based MLP effort.

Trusted Truck(R) II (phase A).

DOT National Transportation Integrated Search

2009-01-01

The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

Results of the Clarus regional demonstrations : evaluation of four decision support tools.

DOT National Transportation Integrated Search

2012-01-01

The Clarus Initiative is a research effort of the U.S. Department of Transportation Intelligent Transportation Systems (ITS) Joint Program Offi ce and the Federal Highway Administrations (FHWA) Road Weather Management Program (RWMP) to develop and...

National ITS Program Plan Executive Summary

DOT National Transportation Integrated Search

1995-03-01

THE PURPOSE OF THE NATIONAL ITS PROGRAM PLAN IS TO GUIDE THE DEVELOPMENT AND DEPLOYMENT OF INTELLIGENT TRANSPORTATION SYSTEMS (ITS) IN THE UNITED STATES. THIS FIRST EDITION OF THE PLAN WAS A JOINT EFFORT OF ITS AMERICA AND THE UNITED STATES DEPARTMEN...

Strategic Options for International Participation in Space Exploration: Lessons from U.S.-Japan Defense Cooperation

NASA Technical Reports Server (NTRS)

Hudiburg, John J.; Chinworth, Michael W.

2005-01-01

The President's Commission on Implementation of United States Space Exploration Policy suggests that after NASA establishes the Space Exploration vision architecture, it should pursue international partnerships. Two possible approaches were suggested: multiple independently operated missions and an integrated mission with carefully selected international components. The U.S.-Japan defense sectors have learned key lessons from experience with both of these approaches. U.S.-Japan defense cooperation has evolved over forty years from simple military assistance programs to more complex joint development efforts. With the evolution of the political-military alliance and the complexity of defense programs, these cooperative efforts have engaged increasingly industrial resources and capabilities as well as more sophisticated forms of planning, technology transfers and program management. Some periods of this evolution have been marked by significant frictions. The U.S.Japan FS-X program, for example, provides a poor example for management of international cooperation. In November 1988, the United States and Japan signed a Memorandum of Understanding (MOU) to co-develop an aircraft, named FS-X and later renamed F -2, as a replacement to the aging Japan support fighter F-l. The program was marked by numerous political disputes. After over a decade of joint development and testing, F -2 production deliveries finally began in 1999. The production run was curtailed due to much higher than anticipated costs and less than desired aircraft performance. One universally agreed "lesson" from the FSX/F-2 case was that it did not represent the ideal approach to bilateral cooperation. More recent cooperative programs have involved targeted joint research and development, including component development for ballistic missile defense systems. These programs could lay the basis for more ambitious cooperative efforts. This study examines both less-than-stellar international cooperation efforts as well as more successful initiatives to identify lessons from military programs that can help NASA encourage global investment in its Space Exploration Vision. The paper establishes a basis for examining related policy and industrial concerns such as effective utilization of dual-use technologies and trans-Pacific program management of large, complex cooperative programs.

Wear analysis and finishing of bioceramic implant surfaces.

PubMed

Denkena, Berend; Reichstein, Martin; van der Meer, Marijke; Ostermeier, Sven; Hurschler, Christof

2008-01-01

A primary cause for revision operations of joint replacements is the implant loosening, due to immune reactions resulting from the agglomeration of polyethylene wear debris. Motivated by the successful application of bioceramic materials in hip joint prostheses, a trend towards the development of hard implant materials has occurred. Nonetheless in the area of total knee arthroplasty (TKA), modern efforts have still utilized polyethylene as the tibial-inlay joint component. The use of bioceramic hard-hard-pairings for total knee arthroplasty has been prevented by the complex kinematics and geometries required. Ceramics cannot cope with non-uniform loads, which suggests the need for new designs appropriate to the material. Furthermore, biomechanical requirements should be considered. A rolling-gliding wear simulator, which reproduces the movements and stresses of the knee joint on specimens of simplified geometry, has therefore been developed. High-precision machining processes for free formed bioceramic surfaces, with suitable grinding and polishing tools which adjust to constantly changing contact conditions, are essential. The goal is to put automated finishing in one clamping with five simultaneous controlled axes into practice. The developed manufacturing technologies will allow the advantageous bioceramic materials to be applied and accepted for more complex joint replacements such as knee prostheses.

76 FR 8788 - National Nanotechnology Coordination Office; Bridging NanoEHS Research Efforts: A Joint US-EU...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-15

... OFFICE OF SCIENCE AND TECHNOLOGY POLICY National Nanotechnology Coordination Office; Bridging NanoEHS Research Efforts: A Joint US-EU Workshop: Public Meeting AGENCY: National Nanotechnology Coordination Office, STPO. ACTION: Notice of public meeting. SUMMARY: The National Nanotechnology Coordination...

EMERGING TECHNOLOGY SUMMARY: ELECTRO-PURE ALTERNATING CURRENT ELECTROCOAGULATION

EPA Science Inventory

The Superfund Innovative Technology Evaluation (SITE) Program was authorized as part of the 1986 amendments to the Superfund legislation. It represents a joint effort between the U.S. Environmental Protection Agency’s (EPA) Office of Research and Development and Office of Solid W...

National ITS Program Plan, Intelligent Transportation Systems, Synopsis

DOT National Transportation Integrated Search

THE PURPOSE OF THE NATIONAL ITS PROGRAM PLAN IS TO GUIDE THE DEVELOPMENT AND DEPLOYMENT OF INTELLIGENT TRANSPORTATION SYSTEMS (ITS) IN THE UNITED STATES. THIS, THE FIRST EDITION OF THE PLAN WAS A JOINT EFFORT OF ITS AMERICA AND THE UNITED STATES DEPA...

Development of an Interdisciplinary, Intercultural Master's Program on Sustainability: Learning from the Richness of Diversity

ERIC Educational Resources Information Center

van Dam-Mieras, Rietje; Lansu, Angelique; Rieckmann, Marco; Michelsen, Gerd

2008-01-01

The purpose of this article is to describe a joint effort between three European and six Latin American universities to create an international Master's degree program on Sustainable Development and Management. Faculty members from these institutions are working together on this unusual and innovative project, which recognizes the importance of…

Service-Learning Linking Family Child Care Providers, Community Partners, and Preservice Professionals

ERIC Educational Resources Information Center

Garner, Pamela W.; Parker, Tameka S.

2016-01-01

This article describes the implementation of a service-learning project, which was infused into a child development course. The project linked family child care providers, their licensing agency, and 39 preservice teachers in a joint effort to develop a parent handbook to be used by the providers in their child care businesses and to support…

Design and technical support for development of a molded fabric space suit joint

NASA Technical Reports Server (NTRS)

Olson, L. Howard

1994-01-01

NASA Ames Research Center has under design a new joint or element for use in a space suit. The design concept involves molding a fabric to a geometry developed at Ames. Unusual characteristics of this design include the need to produce a fabric molding draw ratio on the order of thirty percent circumferentially on the surface. Previous work done at NASA on molded fabric joints has shown that standard, NASA qualified polyester fabrics as are currently available in the textile industry for use in suits have a maximum of about fifteen percent draw ratio. NASA has done the fundamental design for a prototype joint and of a mold which would impart the correct shape to the fabric support layer of the joint. NASA also has the capability to test a finished product for suitability and reliability. Responsibilities resting with Georgia Tech in the design effort for this project are textile related, namely fiber selection, fabric design to achieve the properties of the objective design, and determining production means and sources for the fabrics. The project goals are to produce a prototype joint using the NASA design for evaluation of effectiveness by NASA, and to establish the sources and specifications which would allow reliable and repeatable production of the joint.

Damage detection of an in-service condensation pipeline joint

NASA Astrophysics Data System (ADS)

Briand, Julie; Rezaei, Davood; Taheri, Farid

2010-04-01

The early detection of damage in structural or mechanical systems is of vital importance. With early detection, the damage may be repaired before the integrity of the system is jeopardized, resulting in monetary losses, loss of life or limb, and environmental impacts. Among the various types of structural health monitoring techniques, vibration-based methods are of significant interest since the damage location does not need to be known beforehand, making it a more versatile approach. The non-destructive damage detection method used for the experiments herein is a novel vibration-based method which uses an index called the EMD Energy Damage Index, developed with the aim of providing improved qualitative results compared to those methods currently available. As part of an effort to establish the integrity and limitation of this novel damage detection method, field testing was completed on a mechanical pipe joint on a condensation line, located in the physical plant of Dalhousie University. Piezoceramic sensors, placed at various locations around the joint were used to monitor the free vibration of the pipe imposed through the use of an impulse hammer. Multiple damage progression scenarios were completed, each having a healthy state and multiple damage cases. Subsequently, the recorded signals from the healthy and damaged joint were processed through the EMD Energy Damage Index developed in-house in an effort to detect the inflicted damage. The proposed methodology successfully detected the inflicted damages. In this paper, the effects of impact location, sensor location, frequency bandwidth, intrinsic mode functions, and boundary conditions are discussed.

36 CFR 910.1 - Policy.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Development Area had an adverse impact upon the physical, economic, and social life of Washington, DC. The...—1974, as amended (the Plan) is a blueprint for social, economic, and architectural rejuvenation of the... Nation's Capital, proudly displaying the successful joint efforts of the Corporation, other Federal and...

Evaluation of an Action-Research Project by University Environmental Volunteers

ERIC Educational Resources Information Center

Raimondo, Ana Maria; Monti, Alejandro J. A.; Perales-Palacios, F. Javier; Gutiérrez-Pérez, José

2017-01-01

The university volunteer programs in Argentina encourage entrepreneurship culture through the development of innovative socio-environmental projects that promote a joint effort between the different administrations of the State, the universities and regional social organizations. One, called "environment and social inclusion" has been…

USE OF ELECTROKINETICS FOR HAZARDOUS WASTE SITE REMEDIATION

EPA Science Inventory

The Superfund Innovative Technology Evaluation (SITE) program was authorized as part of the 1986 amendments to the Superfund legislation. It represents a joint effort between U.S. EPA`s Office of Research and Development and Office of Solid Waste and Emergency Response. The progr...

National ITS Program Plan, Intelligent Transportation Systems Volume II

DOT National Transportation Integrated Search

1995-03-01

THE PURPOSE OF THE NATIONAL ITS PROGRAM PLAN IS TO GUIDE THE DEVELOPMENT AND DEPLOYMENT OF INTELLIGENT TRANSPORTATION SYSTEMS (ITS) IN THE UNITED STATES. THIS, THE FIRST EDITION OF THE PLAN WAS A JOINT EFFORT OF ITS AMERICA AND THE UNITED STATES DEPA...

Technical Status Report: Preliminary Glass Formulation Report for INEEL HAW

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D.; Reamer, I.; Vienna, J.

1998-03-01

This study was performed by a team comprising experts in glass chemistry, glass technology, and statistics at both SRTC and PNNL. This joint effort combined the strengths of each discipline and site to quickly develop a glass formulation for specific INEEL HAW.

36 CFR 910.1 - Policy.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Development Area had an adverse impact upon the physical, economic, and social life of Washington, DC. The...—1974, as amended (the Plan) is a blueprint for social, economic, and architectural rejuvenation of the... Nation's Capital, proudly displaying the successful joint efforts of the Corporation, other Federal and...

Farmers Functional Literacy Programme.

ERIC Educational Resources Information Center

Ministry of Education and Social Welfare, New Delhi (India).

The Farmers Training and Functional Literacy Programme, initiated by the government of India in 1968, was an effort to translate into practice the concept of linking education (not only vocational training) to development, particularly for increasing production. The project, a joint enterprise of three government ministries, provides participating…

Spacecraft environmental interactions: A joint Air Force and NASA research and technology program

NASA Technical Reports Server (NTRS)

Pike, C. P.; Purvis, C. K.; Hudson, W. R.

1985-01-01

A joint Air Force/NASA comprehensive research and technology program on spacecraft environmental interactions to develop technology to control interactions between large spacecraft systems and the charged-particle environment of space is described. This technology will support NASA/Department of Defense operations of the shuttle/IUS, shuttle/Centaur, and the force application and surveillance and detection missions, planning for transatmospheric vehicles and the NASA space station, and the AFSC military space system technology model. The program consists of combined contractual and in-house efforts aimed at understanding spacecraft environmental interaction phenomena and relating results of ground-based tests to space conditions. A concerted effort is being made to identify project-related environmental interactions of concern. The basic properties of materials are being investigated to develop or modify the materials as needed. A group simulation investigation is evaluating basic plasma interaction phenomena to provide inputs to the analytical modeling investigation. Systems performance is being evaluated by both groundbased tests and analysis.

To Wield Excalibur: Seeking Unity of Effort in Joint Information Operations

DTIC Science & Technology

2002-06-07

University of Michigan. In 1994, they co-authored a book called “Competing for the Future” in which they introduce the concepts of strategic intent ... strategic architecture, and then to help “build” that future. According to Hamel and Prahalad , a strategic architecture is a “high-level blueprint for the...Figure 6: Develop JIO Intellectual Leadership. It shows that the JIOST would be responsible for setting the Strategic Intent of our IO efforts

Electronic Health Records: DOD and VA Should Remove Barriers and Improve Efforts to Meet Their Common System Needs

DTIC Science & Technology

2011-02-01

and develop joint information technology (IT) capabilities for the James A. Lovell Federal Health Care Center ( FHCC ). In light of these efforts...Center to form the James A. Lovell Federal Health Care Center ( FHCC ) has prompted the departments to work toward implementing electronic health...information needs for the FHCC . To do this, GAO analyzed departmental reviews and other documentation and interviewed DOD and VA officials. What

Climate Scenarios for the NASA / USAID SERVIR Project: Challenges for Multiple Planning Horizons

NASA Technical Reports Server (NTRS)

Robertson, Franklin R.; Roberts, J. B.; Lyon, B.; Funk, C.; Bosilovich, M. G.

2014-01-01

SERVIR, an acronym meaning "to serve" in Spanish, is a joint venture between NASA and the U.S. Agency for International Development (USAID) which provides satellite-based Earth observation data, modeling, and science applications to help developing nations in Central America, East Africa and the Himalayas improve environmental decision making. Anticipating climate variability / climate change impacts has now become an important component of the SERVIR efforts to build capacity in these regions. Uncertainty in hydrometeorological components of climate variations and exposure to extreme events across scales from weather to climate are of particular concern. We report here on work to construct scenarios or outlooks that are being developed as input drivers for decision support systems (DSSs) in a variety of settings. These DSSs are being developed jointly by a broad array NASA Applied Science Team (AST) Investigations and user communities in the three SERVIR Hub Regions, Central America, East Africa and the Himalayas. Issues span hydrologic / water resources modeling, agricultural productivity, and forest carbon reserves. The scenarios needed for these efforts encompass seasonal forecasts, interannual outlooks, and likely decadal / multi-decadal trends. Providing these scenarios across the different AST efforts enables some level of integration in considering regional responses to climate events. We will discuss a number of challenges in developing this continuum of scenarios including the identification and "mining" of predictability, addressing multiple continental regions, issues of downscaling global model integrations to regional / local applications (i.e. hydrologic and crop modeling). We compare / contrast the role of the U.S. National Multi- Model Experiment initiative in seasonal forecasts and the CMIP-5 climate model experiments in supporting these efforts. Examples of these scenarios, their use, and an assessment of their utility as well as limitations will be presented.

Manpower and Employment Policies for Developing Countries, Proceedings of the International Manpower Seminar. (7th, September 28-December 10, 1966).

ERIC Educational Resources Information Center

Bussey, Ellen M.

The Seminar, a joint venture of the Agency for International Development and the Labor Department of the United States, brought together 29 participants from 20 developing countries for the purpose of exchanging ideas and experiences on manpower programs and planning efforts. These proceedings are the result of notes taken by reporters during the…

Joint Force Cyberspace Component Command: Establishing Cyberspace Operations Unity of Effort for the Joint Force Commander

DTIC Science & Technology

2015-05-01

say/. According to the article, “the hackers targeted big-name makers of nuclear and solar technology, stealing confidential business information...As JTF-GNO synchronized efforts to disinfect and protect over 2.5 million computers in 3,500 DoD organizations spanning 99 countries, Defense

Using Kepler Light Curves for Astronomy Education and Public Outreach

NASA Astrophysics Data System (ADS)

Cash, Jennifer; Rivers, S.; Eleby, J.; Gould, A.; Komatsu, T.

2014-01-01

We will present our efforts related to Education and Public Outreach activities using Kepler Light Curves. We are currently developing interactive web based activities to introduce the public to the general topic of Stellar Variability and Intrinsic Variable Stars in particular using the high quality light curves of over a dozen Kepler targets. Along with the public website, we are exploring areas to develop teacher guides to use Kepler Light Curves in the middle and high school classrooms. These efforts are supported through a NASA EPSCoR grant "South Carolina Joint Venture Program" via a subaward to SC State University.

Improved Advanced Actuated Hybrid Mirrors Final Report CRADA No. TC02130.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barbee, T. W.; Ealey, M. A.

2017-08-25

This was a collaborative effort to develop and demonstrate an improved Advanced Actuated Hybrid Mirrors (AAHM) for commercial or Government purposes. The AAHM consists of a nanolaminate film replicating a precision optical surface bonded to a Silicon Carbide (SiC) substrate with active figure control capability. The goal of this project was to further the development of specific AAHM technologies. The intent of the CRADA was to combine the expertise of LLNL and NG Xinetics in the manufacture and test of a very high quality AAHM, incorporating lessons learned from earlier joint efforts.

SERVIR Support to NSDI Efforts in Mesoamerica, Africa and the Himalayas

NASA Technical Reports Server (NTRS)

Delgado, Francisco

2014-01-01

SERVIR is a joint effort between NASA, USAID to build or improve capacities in developing regions to help adaptation to climate change by taking advantage of Earth Observation data for decision making. The project began in 2004, in Mesoamerica, partnering with the Central American Commission for Environment and Development(CCAD), the World Bank and CATHALAC. CATHALAC, located in Panama, serves as the regional hub for Mesoamerica since 2005. Two additional regional hubs have been established (in Easters & Western Africa - at RCMRD, Kenya, and The Himalayas- at ICIMOD, Nepal), and two more regional hubs are soon to be launched.

VLT/I Instrumentation: Lessons Learned FORUM

NASA Astrophysics Data System (ADS)

Monnet, G.; Bacon, R.

2003-09-01

This paper is the result of a joint effort by ESO and its Scientific and Technical Committee (STC) to extract the main lessons from last April's 'VLT/VLTI Instrumentation: Lessons learned' Forum and start applying them, in particular in the framework of the development of second generation VLT -and soon VLTI- instruments. This is but one step in a continuing effort to optimize these complex and challenging developments which involve a significant fraction of Europe's astronomical instrument builders in the near-UV to mid-IR range. With a major effort in the European radio community to build multiple receiver systems for ALMA now being pursued at an accelerated pace, it was also vital to revisit very quickly our whole procurement strategy in this area.

FATE AND TRANSPORT MODELING OF CONTAMINANTS OF CONCERN FROM A CAFO IN AN AGRICULTURAL WATERSHED

EPA Science Inventory

The groundwater flow and transport modeling effort will require hydrogeological site characterization and the development of a conceptual flow model for the site. Site characterization will involve an assessment of both the surface and subsurface and be accomplished through joint...

Longitudinal joint treatment.

DOT National Transportation Integrated Search

2006-03-01

Maine highways have been showing signs of longitudinal joint failure for a number of years. In an effort : to reduce the amount of joint failures the Maine Department of Transportation (MDOT) is currently : evaluating two projects. One project is mon...

Whole of Government Approach: Maximizing Unity of Effort Between the Department of Defense (DOD), Department of State (DOS), and the United States Agency for International Development (USAID)

DTIC Science & Technology

2013-12-13

role in Global War on Terrorism . The goal of this study is to illustrate a framework to improve interagency cooperation though the Joint...and Edward Marks, “ The Global War on Terrorism : A Regional Approach to Coordination,” Joint Force Quarterly no. 32 (Autumn 2002): 50. 6...second mission was to provide civil support to Civilian Irregular Defense Groups (CIDG), which were established to win the loyalty of the aboriginal

Defense Department Cyber Efforts: More Detailed Guidance Needed to Ensure Military Services Develop Appropriate Cyberspace Capabilities

DTIC Science & Technology

2011-05-01

communications and on computer networks—its Global Information Grid—which are potentially jeopardized by the millions of denial-of-service attacks, hacking ...Director,a National Security Agency Chief of Staff Joint Operations Center Defense Information Systems Agency Command Center J1 J2 J3 J4 J5 J6 J7 J8...DC Joint Staff • J39, Operations, Pentagon, Washington, DC • J5 , Strategic Plans and Policy, Pentagon, Washington, DC U.S. Strategic Command • J882

Transition process from emerging NDT technology to production inspection application

NASA Astrophysics Data System (ADS)

Jappe, William; Wood, Nancy; Johnson, Maurice

1995-07-01

The successful application of emerging NDT technologies for specific aging aircraft inspections requires an integration of efforts between aircraft operators, airframe manufacturers, NDT equipment designers, and government regulators. This paper describes the development process that was followed to establish an alternate inspection technique for a DC-10 crown skin butt joint inspection. Initial investigation, intermediate development, and final evaluations are discussed.

Status of Activities to Implement a Sustainable System of MC&A Equipment and Methodological Support at Rosatom Facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.D. Sanders

Under the U.S.-Russian Material Protection, Control and Accounting (MPC&A) Program, the Material Control and Accounting Measurements (MCAM) Project has supported a joint U.S.-Russian effort to coordinate improvements of the Russian MC&A measurement system. These efforts have resulted in the development of a MC&A Equipment and Methodological Support (MEMS) Strategic Plan (SP), developed by the Russian MEM Working Group. The MEMS SP covers implementation of MC&A measurement equipment, as well as the development, attestation and implementation of measurement methodologies and reference materials at the facility and industry levels. This paper provides an overview of the activities conducted under the MEMS SP,more » as well as a status on current efforts to develop reference materials, implement destructive and nondestructive assay measurement methodologies, and implement sample exchange, scrap and holdup measurement programs across Russian nuclear facilities.« less

Longitudinal joint treatment : construction report.

DOT National Transportation Integrated Search

2000-05-01

Maine highways have been showing signs of longitudinal joint failure for a number of : years. In an effort to reduce the amount of joint failures the Maine Department of : Transportation (MDOT) is currently evaluating two projects. One project is mon...

Description of and preliminary tests results for the Joint Damping Experiment (JDX)

NASA Technical Reports Server (NTRS)

Bingham, Jeffrey G.; Folkman, Steven L.

1995-01-01

An effort is currently underway to develop an experiment titled joint Damping E_periment (JDX) to fly on the Space Shuttle as Get Away Special Payload G-726. This project is funded by NASA's IN-Space Technology Experiments Program and is scheduled to fly in July 1995 on STS-69. JDX will measure the influence of gravity on the structural damping of a three bay truss having clearance fit pinned joints. Structural damping is an important parameter in the dynamics of space structures. Future space structures will require more precise knowledge of structural damping than is currently available. The mission objectives are to develop a small-scale shuttle flight experiment that allows researchers to: (1) characterize the influence of gravity and joint gaps on structural damping and dynamic behavior of a small-scale truss model, and (2) evaluate the applicability of low-g aircraft test results for predicting on-orbit behavior. Completing the above objectives will allow a better understanding and/or prediction of structural damping occurring in a pin jointed truss. Predicting damping in joints is quite difficult. One of the important variables influencing joint damping is gravity. Previous work has shown that gravity loads can influence damping in a pin jointed truss structure. Flying this experiment as a GAS payload will allow testing in a microgravity environment. The on-orbit data (in micro-gravity) will be compared with ground test results. These data will be used to help develop improved models to predict damping due to pinned joints. Ground and low-g aircraft testing of this experiment has been completed. This paper describes the experiment and presents results of both ground and low-g aircraft tests which demonstrate that damping of the truss is dramatically influenced by gravity.

Coach Education Online: The Montana Model

ERIC Educational Resources Information Center

Stewart, Craig

2006-01-01

Coach education is important, but expensive--both in cost and time to public and private athletic programs. To provide basic coach education to coaches, new, innovative, inexpensive approaches must be developed. Joint efforts between state high school associations and colleges and universities can meet those needs. The "Montana approach"…

Preservation Health Check: Monitoring Threats to Digital Repository Content

ERIC Educational Resources Information Center

Kool, Wouter; van der Werf, Titia; Lavoie, Brian

2014-01-01

The Preservation Health Check (PHC) project, undertaken as a joint effort by Open Planets Foundation (OPF) and OCLC Research, aims to evaluate the usefulness of the preservation metadata created and maintained by operational repositories for assessing basic preservation properties. The PHC project seeks to develop an implementable logic to support…

Amplification, Technology, and Cochlear Implants for Infants.

ERIC Educational Resources Information Center

Adam, Arlie J.

1993-01-01

Early amplification is crucial to efficient habilitation and development of oral communication skills in hearing-impaired infants. Initial evaluation and fitting of amplification is a joint effort by the audiologist, therapist, and parents, whether the child uses traditional hearing aids or cochlear implants, and should be supplemented by a…

AN OVERVIEW OF THE UNCERTAINTY ANALYSIS, SENSITIVITY ANALYSIS, AND PARAMETER ESTIMATION (UA/SA/PE) API AND HOW TO IMPLEMENT IT

EPA Science Inventory

The Application Programming Interface (API) for Uncertainty Analysis, Sensitivity Analysis, and
Parameter Estimation (UA/SA/PE API) (also known as Calibration, Optimization and Sensitivity and Uncertainty (CUSO)) was developed in a joint effort between several members of both ...

Developing anti-inflammatory therapeutics for patients with osteoarthritis.

PubMed

Philp, Ashleigh M; Davis, Edward T; Jones, Simon W

2017-06-01

OA is the most common joint disorder in the world, but there are no approved therapeutics to prevent disease progression. Historically, OA has been considered a wear-and-tear joint disease, and efforts to identify and develop disease-modifying therapeutics have predominantly focused on direct inhibition of cartilage degeneration. However, there is now increasing evidence that inflammation is a key mediator of OA joint pathology, and also that the link between obesity and OA is not solely due to excessive load-bearing, suggesting therefore that targeting inflammation in OA could be a rewarding therapeutic strategy. In this review we therefore re-evaluate historical clinical trial data on anti-inflammatory therapeutics in OA patients, highlight some of the more promising emerging therapeutic targets and discuss the implications for future clinical trial design. © The Author 2016. Published by Oxford University Press on behalf of the British Society for Rheumatology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Longitudinal joint treatment : first interim report.

DOT National Transportation Integrated Search

2000-11-01

Maine highways have been showing signs of longitudinal joint failure for a number of : years. In an effort to reduce the amount of joint failures the Maine Department of : Transportation (MDOT) is currently evaluating two projects. One project is mon...

Longitudinal joint treatment : second interim report.

DOT National Transportation Integrated Search

2001-09-01

Maine highways have been showing signs of longitudinal joint failure for a : number of years. In an effort to reduce the amount of joint failures the Maine : Department of Transportation (MDOT) is currently evaluating two projects. One : project is m...

United States Research and Development effort on ITER magnet tasks

DOE PAGES

Martovetsky, Nicolai N.; Reierson, Wayne T.

2011-01-22

This study presents the status of research and development (R&D) magnet tasks that are being performed in support of the U.S. ITER Project Office (USIPO) commitment to provide a central solenoid assembly and toroidal field conductor for the ITER machine to be constructed in Cadarache, France. The following development tasks are presented: winding development, inlets and outlets development, internal and bus joints development and testing, insulation development and qualification, vacuum-pressure impregnation, bus supports, and intermodule structure and materials characterization.

Senior Student Affairs Officers' Reports of Joint Intra-Institutional Efforts to Support College Students with Mental Illness

ERIC Educational Resources Information Center

Scheidel, Sarah

2016-01-01

The purpose of this sequential mixed-methods study was to explore senior student affairs officers' reports of joint intra-institutional efforts within the past three years to achieve the common goal of supporting the academic and personal success of college students with mental illness. The 20 factors identified by Mattessich, Murray-Close, and…

HART-II: Prediction of Blade-Vortex Interaction Loading

NASA Technical Reports Server (NTRS)

Lim, Joon W.; Tung, Chee; Yu, Yung H.; Burley, Casey L.; Brooks, Thomas; Boyd, Doug; vanderWall, Berend; Schneider, Oliver; Richard, Hugues; Raffel, Markus

2003-01-01

During the HART-I data analysis, the need for comprehensive wake data was found including vortex creation and aging, and its re-development after blade-vortex interaction. In October 2001, US Army AFDD, NASA Langley, German DLR, French ONERA and Dutch DNW performed the HART-II test as an international joint effort. The main objective was to focus on rotor wake measurement using a PIV technique along with the comprehensive data of blade deflections, airloads, and acoustics. Three prediction teams made preliminary correlation efforts with HART-II data: a joint US team of US Army AFDD and NASA Langley, German DLR, and French ONERA. The predicted results showed significant improvements over the HART-I predicted results, computed about several years ago, which indicated that there has been better understanding of complicated wake modeling in the comprehensive rotorcraft analysis. All three teams demonstrated satisfactory prediction capabilities, in general, though there were slight deviations of prediction accuracies for various disciplines.

SRB Environment Evaluation and Analysis. Volume 2: RSRB Joint Filling Test/Analysis Improvements

NASA Technical Reports Server (NTRS)

Knox, E. C.; Woods, G. Hamilton

1991-01-01

Following the Challenger accident a very comprehensive solid rocket booster (SRB) redesign program was initiated. One objective of the program was to develop expertise at NASA/MSFC in the techniques for analyzing the flow of hot gases in the SRB joints. Several test programs were undertaken to provide a data base of joint performance with manufactured defects in the joints to allow hot gases to fill the joints. This data base was used also to develop the analytical techniques. Some of the test programs were Joint Environment Simulator (JES), Nozzle Joint Environment Simulator (NJES), Transient Pressure Test Article (TPTA), and Seventy-Pound Charge (SPC). In 1988 the TPTA test hardware was moved from the Utah site to MSFC and several RSRM tests were scheduled, to be followed by tests for the ASRM program. REMTECH Inc. supported these activities with pretest estimates of the flow conditions in the test joints, and post-test analysis and evaluation of the measurements. During this support REMTECH identified deficiencies in the gas-measurement instrumentation that existed in the TPTA hardware, made recommendations for its replacement, and identified improvements to the analytical tools used in the test support. Only one test was completed under the TPTA RSRM test program, and those scheduled for the ASRM were rescheduled to a time after the expiration of this contract. The attention of this effort was directed toward improvements in the analytical techniques in preparation for when the ASRM program begins.

Longitudinal joint treatment, interim report - third year, March 2004.

DOT National Transportation Integrated Search

2004-03-01

Maine highways have been showing signs of longitudinal joint failure for a number of years. In an effort : to reduce the amount of joint failures the Maine Department of Transportation (MDOT) is currently : evaluating two projects. One project is mon...

Longitudinal joint treatment, interim report - fourth year, March 2005.

DOT National Transportation Integrated Search

2005-03-01

Maine highways have been showing signs of longitudinal joint failure for a number of years. In an effort : to reduce the amount of joint failures the Maine Department of Transportation (MDOT) is currently : evaluating two projects. One project is mon...

Coordinated fee structure for developed recreation sites on the Ashley, Uinta, and Wasatch-Cache National Forests

Treesearch

Brent H. McBeth

1995-01-01

A joint effort between three National Forests in northern Utah was begun to provide a uniform process for establishing fees at developed recreation sites, based upon the "cost approach" method. This method can be adapted for other National Forest and District use and can be modified to reflect "comparable fees" and updated periodically to meet local...

Development of wavelet analysis tools for turbulence

NASA Technical Reports Server (NTRS)

Bertelrud, A.; Erlebacher, G.; Dussouillez, PH.; Liandrat, M. P.; Liandrat, J.; Bailly, F. Moret; Tchamitchian, PH.

1992-01-01

Presented here is the general framework and the initial results of a joint effort to derive novel research tools and easy to use software to analyze and model turbulence and transition. Given here is a brief review of the issues, a summary of some basic properties of wavelets, and preliminary results. Technical aspects of the implementation, the physical conclusions reached at this time, and current developments are discussed.

Far-Infrared Blocked Impurity Band Detector Development

NASA Technical Reports Server (NTRS)

Hogue, H. H.; Guptill, M. T.; Monson, J. C.; Stewart, J. W.; Huffman, J. E.; Mlynczak, M. G.; Abedin, M. N.

2007-01-01

DRS Sensors & Targeting Systems, supported by detector materials supplier Lawrence Semiconductor Research Laboratory, is developing far-infrared detectors jointly with NASA Langley under the Far-IR Detector Technology Advancement Partnership (FIDTAP). The detectors are intended for spectral characterization of the Earth's energy budget from space. During the first year of this effort we have designed, fabricated, and evaluated pilot Blocked Impurity Band (BIB) detectors in both silicon and germanium, utilizing pre-existing customized detector materials and photolithographic masks. A second-year effort has prepared improved silicon materials, fabricated custom photolithographic masks for detector process, and begun detector processing. We report the characterization results from the pilot detectors and other progress.

Recent Advances in Tissue Engineering Strategies for the Treatment of Joint Damage.

PubMed

Stephenson, Makeda K; Farris, Ashley L; Grayson, Warren L

2017-08-01

While the clinical potential of tissue engineering for treating joint damage has yet to be realized, research and commercialization efforts in the field are geared towards overcoming major obstacles to clinical translation, as well as towards achieving engineered grafts that recapitulate the unique structures, function, and physiology of the joint. In this review, we describe recent advances in technologies aimed at obtaining biomaterials, stem cells, and bioreactors that will enable the development of effective tissue-engineered treatments for repairing joint damage. 3D printing of scaffolds is aimed at improving the mechanical structure and microenvironment necessary for bone regeneration within a damaged joint. Advances in our understanding of stem cell biology and cell manufacturing processes are informing translational strategies for the therapeutic use of allogeneic and autologous cells. Finally, bioreactors used in combination with cells and biomaterials are promising strategies for generating large tissue grafts for repairing damaged tissues in pre-clinical models. Together, these advances along with ongoing research directions are making tissue engineering increasingly viable for the treatment of joint damage.

Economic Development and Diversification in Southwest Louisiana

DTIC Science & Technology

1989-11-01

0.76 Joint research and development 0.77 0.56 Small-business incubator sites 0.46 0.73 Develop foreign export markets 0.77 0.29 Average 0.85 1.11 Note... marketing plan will be a key element in the acquisition of capital and finance for the corporation. The service that Gulf South Research Corporation...effort. The company itself has embarked on its own internal diversification strategy by continuing to develop new markets for its products. There are many

A field evaluation of Transflex bridge joint performance.

DOT National Transportation Integrated Search

1972-01-01

Presented are the results of a field evaluation of the various types of the General Tire Transflex joint known to be in use in Virginia. An effort was made, whenever possible, to qualitatively evaluate the joints with respect to their (1) watertightn...

Quantifying Astronaut Tasks: Robotic Technology and Future Space Suit Design

NASA Technical Reports Server (NTRS)

Newman, Dava

2003-01-01

The primary aim of this research effort was to advance the current understanding of astronauts' capabilities and limitations in space-suited EVA by developing models of the constitutive and compatibility relations of a space suit, based on experimental data gained from human test subjects as well as a 12 degree-of-freedom human-sized robot, and utilizing these fundamental relations to estimate a human factors performance metric for space suited EVA work. The three specific objectives are to: 1) Compile a detailed database of torques required to bend the joints of a space suit, using realistic, multi- joint human motions. 2) Develop a mathematical model of the constitutive relations between space suit joint torques and joint angular positions, based on experimental data and compare other investigators' physics-based models to experimental data. 3) Estimate the work envelope of a space suited astronaut, using the constitutive and compatibility relations of the space suit. The body of work that makes up this report includes experimentation, empirical and physics-based modeling, and model applications. A detailed space suit joint torque-angle database was compiled with a novel experimental approach that used space-suited human test subjects to generate realistic, multi-joint motions and an instrumented robot to measure the torques required to accomplish these motions in a space suit. Based on the experimental data, a mathematical model is developed to predict joint torque from the joint angle history. Two physics-based models of pressurized fabric cylinder bending are compared to experimental data, yielding design insights. The mathematical model is applied to EVA operations in an inverse kinematic analysis coupled to the space suit model to calculate the volume in which space-suited astronauts can work with their hands, demonstrating that operational human factors metrics can be predicted from fundamental space suit information.

Operational space weather product development and validation at the joint SMC-AFRL Rapid Prototyping Center

NASA Astrophysics Data System (ADS)

Quigley, S.

The Air Force Research Laboratory (AFRL/VSB) and Detachment 11, Space &Missile Systems Center (SMC, Det 11/CIT) have combined efforts to design, develop, test, and implement graphical products for the Air Force's space weather operations center. These products are generated to analyze, specify, and forecast the effects of the near-earth space environment on Department of Defense systems and communications. Jointly-developed products that have been, or will soon be added to real-time operations include: 1) the Operational Space Environment Network Display (OpSEND) suit - a set of four products that address HF communication, UHF satellite communication scintillation, radar auroral clutter, and GP S single- frequency errors; 2) a solar radio background and burst effects (SoRBE) product suite; and C) a meteor effects (ME) product suite. The RPC is also involved in a rather substantial "V&V" effort to produce multiple operational product verifications and validations, with an added end goal of a generalized validation software package. The presentation will provide a general overview of the RPC and each of the products mentioned above, to include background science, operational history, inputs, outputs, dissemination, and customer uses for each.

Potential for extending major land resource areas into northern Mexico

Treesearch

Roy S. Mann; Philip Heilman; Jeffry Stone

2013-01-01

There is a significant history of cooperative efforts between Mexico and the United States on natural resource management issues. Mexico and the United States have jointly conducted research and developed range management technologies. Bringing these technologies together and improving technical communications are an ongoing process. This paper discusses a potential...

Consortium for Innovative Instruction: Aligning Writing Instruction in Secondary and Postsecondary Institutions.

ERIC Educational Resources Information Center

Jennings, Chris

The TCC/FIPSE Writing Coalition, the joint project between Tidewater Community College (TCC) (Virginia) and the Fund for Improvement of Postsecondary Education (FIPSE), was developed in an effort to eliminate remedial instruction in writing for recent high school graduates. The project is an outgrowth of student-centered approaches to instruction…

Enhancing Overseas Chinese Graduate Employability: The Case of Chinese Graduates with Finnish Academic Qualifications

ERIC Educational Resources Information Center

Cai, Yuzhuo

2014-01-01

This paper explores ways to enhance overseas Chinese graduate employability by taking Finnish-educated Chinese students/graduates as an example. In so doing, it understands that graduate employability development is a joint effort of multiple stakeholders including students, graduates, academics, program coordinators, employers, and policymakers.…

LAMP Whys? LAMP Wise! A Practical Guide to the Lansing Area Manufacturing Partnership.

ERIC Educational Resources Information Center

MacAllum, Keith; McDonald, Deanne; Johnson, Amy Bell

This document profiles the Lansing Area Manufacturing Partnership (LAMP), which is a model school-to-career initiative featuring an innovative integrated, employer-driven curriculum that was designed, developed, and implemented through the joint efforts of the Ingham Intermediate School District in Lansing, Michigan, the United Auto Workers (UAW),…

History and Status of School Psychology Accreditation in the United States.

ERIC Educational Resources Information Center

Fagan, Thomas K.; Wells, Perri Dawn

2000-01-01

A history of school psychology accreditation and a chronology of program decisions are developed from perspectives on accreditation by the American Psychological Association (APA), the National Council for Accreditation in Teacher Education (NCATE), the National Association of School Psychologists (NASP), and the efforts of the APA/NASP Joint Task…

Start-Up Training in Mississippi: Program Development Guide.

ERIC Educational Resources Information Center

Brooks, Kent; And Others

Due to recent industrial growth in Mississippi and the shortage of trained manpower in numerous occupations, start-up training programs have originated to provide a pretrained work force for new or expanding industry in the State. Each start-up training program is a joint effort between a new or expanding industry and a public educational…

Summary of U.S. research on wood transportation structures

Treesearch

M. A. Ritter; R. C. Moody; S. R. Duwadi

1996-01-01

An extensive U.S. research program to further develop wood utilization in transportation structures is currently in progress as a joint effort of the USDA Forest Service, Forest Products Laboratory, and the U.S. Department of Transportation, Federal Highway Administration. This research is funded primarily by U.S. legislation and involves cooperative research with...

Joint CPT and N resonance in compact atomic time standards

NASA Astrophysics Data System (ADS)

Crescimanno, Michael; Hohensee, Michael; Xiao, Yanhong; Phillips, David; Walsworth, Ron

2008-05-01

Currently development efforts towards small, low power atomic time standards use current-modulated VCSELs to generate phase-coherent optical sidebands that interrogate the hyperfine structure of alkali atoms such as rubidium. We describe and use a modified four-level quantum optics model to study the optimal operating regime of the joint CPT- and N-resonance clock. Resonant and non-resonant light shifts as well as modulation comb detuning effects play a key role in determining the optimal operating point of such clocks. We further show that our model is in good agreement with experimental tests performed using Rb-87 vapor cells.

Old adults perform activities of daily living near their maximal capabilities.

PubMed

Hortobágyi, Tibor; Mizelle, Chris; Beam, Stacey; DeVita, Paul

2003-05-01

Old adults' ability to execute activities of daily living (ADLs) declines with age. One possible reason for this decline is that the execution of customary motor tasks requires a substantially greater effort in old compared with young adults relative to their available maximal capacity. We tested the hypothesis that the relative effort (i.e., the percentage of joint moment relative to maximal joint moment) to execute ADLs is higher in old adults compared with young adults. Healthy young adults (n = 13; mean age, 22 years) and old adults (n = 14; mean age, 74 years) ascended and descended stairs and rose from a chair and performed maximal-effort isometric supine leg press. Using inverse dynamics analysis, we determined knee joint moments in ADLs and computed relative effort. Compared with young adults, old adults had 60% lower maximal leg press moments, 53% slower knee angular velocity at peak torque, and 27% lower knee joint moments in the ADLs (all p <.05). Relative effort in ascent was 54% (SD +/- 16%) and 78% (+/-20%) in young and old adults, respectively; in descent, it was 42% (+/-20%) and 88% (+/-43%); and in chair rise, it was 42% (+/-19%) and 80% (+/-34%) (all p <.05). The relative electromyographic activity of the vastus lateralis and the coactivity of the biceps femoris associated with this relative effort were, respectively, 2- and 1.6-fold greater in old compared with young adults in the 3 ADLs (p <.05). For healthy old adults, the difficulty that arises while performing ADLs may be due more to working at a higher level of effort relative to their maximum capability than to the absolute functional demands imposed by the task.

DICOM version 3.0 demonstration at InfoRAD 1992

NASA Astrophysics Data System (ADS)

Jost, R. Gilbert

1993-09-01

Over the past 10 years, a large number of devoted individuals have worked on a project to develop a standard for the storage and exchange of medical images. Known as the ACR/NEMA standardization effort, this project is jointly sponsored by the American College of Radiology (ACR) and the National Electrical Manufacturers Association (NEMA). Over the years, radiologists and industry representatives alike have supported the standardization effort, but there has been little evidence of actual exchanges of medical images among medical equipment vendors who use the ACR/NEMA standard.

The RMTC as a result of 10-year fruitful joint cooperation of the USA, EC and Russia under NMC&A programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dickman, Deborah A.; Frigola, P.; Guardini, Sergio

The Ministry for Atomic Energy of the Russian Federation made the decision to establish the Russian Methodological and Training Center (RMTC) not only as the leading center on personnel training in nuclear material control and accounting (NMC&A) field, but also as the center for rendering methodological support to specialists and inspectors in the course of development and implementation of a new Russian NMC&A system and to the state authorities in their regulatory activities. The importance of the project on RMTC establishment and development was the main reason for concentrating significant efforts not only of the United States (U.S.) National Laboratoriesmore » but also of the European Commission's (EC) Joint Research Center (JRC). The coordination of their efforts in the projects implemented under the U.S.-Russia cooperative program and Technical Assistance to the Commonwealth of Independent States (TACIS) program resulted in establishing the RMTC, a unique NMC&A methodological and training center in Russia, that has the state-of-the-art instrumentation and tools and highly qualified personnel. The Center has the possibility to invite not only the State Scientific Center of the Russian Federation - Institute of Physics and Power Engineering named after A. I. Leypunsky (IPPE) specialists but also the specialists from other facilities and agencies to serve as instructors. By now the firm basis for methodological activity has been established in the Center. The RMTC specialists render their knowledge and expertise for many projects on NMC&A upgrading. The RMTC methodological activity is primarily concentrated on development of guidelines on the use of new federal and Rosatom NMC&A regulatory documents. This work is being done with the use of resources and potential of the TACIS program and U.S.-Russia MPC&A program. The paper presents a brief summary of the results achieved in the course of RMTC creation and evolution during the 10-year joint Russian, U.S. and EC efforts.« less

Joint Center for Operational Analysis Journal. Volume 12, Issue 1, Spring 2010

DTIC Science & Technology

2010-01-01

enable research into captured records with “complete openness and rigid adherence to acadamic freedom and integrity.” The CRRC will thereby...various levels of effort in the former area, the latter provides a common ground and opportunities for developing close collaborations. This allows...consequence management (CM) capability, specifi cally the use of the CM Decision Support Tool (DST) developed by the DTRA. Ms. Jessica Iannotti

Thriving Together: Connecting Rural School Improvement and Community Development = Prosperando juntos: La conexion entre el mejoramiento de la escuela rural y el desarrollo comunitario.

ERIC Educational Resources Information Center

Boethel, Martha

Available in English or Spanish, this resource guide aims to help rural schools and communities learn ways of supporting each other so that both can thrive. Background information and basic tools are provided for starting a joint school-community development effort. Chapters contain: (1) outline of the guide and statement of beliefs about…

Joint Improvised Explosive Device Defeat Organization Annual Report 2010

DTIC Science & Technology

2010-01-01

Fox is an effort to characterize a COTS, man-portable, radiography system exceeding current EOD radiography penetration capabilities. Gray Fox... rocket propelled grenades at a reduced weight compared to currently available armor solutions. Sentinel Scout. This developmental appliqué kit is...Dismounted System Joint Electronic warfare Cour&e Joint Total Entity Tracking for the Instrumented Battlefield Joint Readinoss Training Contor

Joint Group on Pollution Prevention: Partnering for Progress

NASA Technical Reports Server (NTRS)

Hill, R.

2001-01-01

This viewgraph presentation outlines the Joint Group on Pollution Prevention (JG-PP) partnership. Details are given on what groups comprise JG-PP, the proven methodology for what JG-PP can accomplish, the common problems, joint solutions, and shared efforts, and some of the JG-PP projects.

Staffing effectiveness evaluation: a best kept secret for educational needs assessment.

PubMed

Hanna, Lee Ann

2005-01-01

Staff development educators use many sources of information to conduct educational needs assessments to improve existing educational programs and to develop new ones. Staffing effectiveness evaluation information targets patient care and staffing outcomes. The overall objective of this article is to familiarize staff development educators with the staffing effectiveness evaluation process, events that have led to organizational efforts to measure it, Joint Commission on Accreditation of Healthcare Organizations' (JCAHO) expectations, methods for assessing variation and relationships of indicators, and implications for staff development educators.

The differential diagnosis of children with joint hypermobility: a review of the literature

PubMed Central

Tofts, Louise J; Elliott, Elizabeth J; Munns, Craig; Pacey, Verity; Sillence, David O

2009-01-01

Background In this study we aimed to identify and review publications relating to the diagnosis of joint hypermobility and instability and develop an evidence based approach to the diagnosis of children presenting with joint hypermobility and related symptoms. Methods We searched Medline for papers with an emphasis on the diagnosis of joint hypermobility, including Heritable Disorders of Connective Tissue (HDCT). Results 3330 papers were identified: 1534 pertained to instability of a particular joint; 1666 related to the diagnosis of Ehlers Danlos syndromes and 330 related to joint hypermobility. There are inconsistencies in the literature on joint hypermobility and how it relates to and overlaps with milder forms of HDCT. There is no reliable method of differentiating between Joint Hypermobility Syndrome, familial articular hypermobility and Ehlers-Danlos syndrome (hypermobile type), suggesting these three disorders may be different manifestations of the same spectrum of disorders. We describe our approach to children presenting with joint hypermobility and the published evidence and expert opinion on which this is based. Conclusion There is value in identifying both the underlying genetic cause of joint hypermobility in an individual child and those hypermobile children who have symptoms such as pain and fatigue and might benefit from multidisciplinary rehabilitation management. Every effort should be made to diagnose the underlying disorder responsible for joint hypermobility which may only become apparent over time. We recommend that the term "Joint Hypermobility Syndrome" is used for children with symptomatic joint hypermobility resulting from any underlying HDCT and that these children are best described using both the term Joint Hypermobility Syndrome and their HDCT diagnosis. PMID:19123951

A Quest for Excellence. Appendix

DTIC Science & Technology

1986-06-01

the Joint Staff should be removed to permit the Chairman a staff sufficient to discharge his responsibilities. The Secretary of Defense should direct...better coordinated among DoD agencies and Congress. Guidelines must be developed to remove undesirable duplication of official effort and, when...specifically for commercial overall procurement system, with particular procurement are inconsistent and ineffective, attention given to the removal

A Model for Recruiting and Retaining Teachers in Alaska's Rural K-12 Schools

ERIC Educational Resources Information Center

Adams, Barbara L.; Woods, Ashley

2015-01-01

The Alaska Statewide Mentor Project (ASMP) is a joint effort of the University of Alaska and the Alaska Department of Education & Early Development to address the persistently low teacher retention rates in the state, especially in rural districts that predominantly serve Alaska Native (AN) students. Over six years, teacher retention in rural…

Learning Analysis of K-12 Students' Online Problem Solving: A Three-Stage Assessment Approach

ERIC Educational Resources Information Center

Hu, Yiling; Wu, Bian; Gu, Xiaoqing

2017-01-01

Problem solving is considered a fundamental human skill. However, large-scale assessment of problem solving in K-12 education remains a challenging task. Researchers have argued for the development of an enhanced assessment approach through joint effort from multiple disciplines. In this study, a three-stage approach based on an evidence-centered…

Knowledge Co-production at the Research-Practice Interface: Embedded Case Studies from Urban Forestry

Treesearch

Lindsay K. Campbell; Erika S. Svendsen; Lara A. Roman

2016-01-01

Cities are increasingly engaging in sustainability efforts and investment in green infrastructure, including large-scale urban tree planting campaigns. In this context, researchers and practitioners are working jointly to develop applicable knowledge for planning and managing the urban forest. This paper presents three case studies of knowledge co-production in the...

Sacramento City Unified School District and Sacramento City College Articulation Council Year-End Report.

ERIC Educational Resources Information Center

Giugni, Tom; Burris, Douglas W.

In 1982, the President of Sacramento City College (SCC) and the Superintendent of the Sacramento City Unified School District (SCUSD) developed the new concept of a joint articulation council to address current problems related to the number of under-prepared students and the possible duplication of effort in basic skills instruction and…

Repair and tissue engineering techniques for articular cartilage.

PubMed

Makris, Eleftherios A; Gomoll, Andreas H; Malizos, Konstantinos N; Hu, Jerry C; Athanasiou, Kyriacos A

2015-01-01

Chondral and osteochondral lesions due to injury or other pathology commonly result in the development of osteoarthritis, eventually leading to progressive total joint destruction. Although current progress suggests that biologic agents can delay the advancement of deterioration, such drugs are incapable of promoting tissue restoration. The limited ability of articular cartilage to regenerate renders joint arthroplasty an unavoidable surgical intervention. This Review describes current, widely used clinical repair techniques for resurfacing articular cartilage defects; short-term and long-term clinical outcomes of these techniques are discussed. Also reviewed is a developmental pipeline of acellular and cellular regenerative products and techniques that could revolutionize joint care over the next decade by promoting the development of functional articular cartilage. Acellular products typically consist of collagen or hyaluronic-acid-based materials, whereas cellular techniques use either primary cells or stem cells, with or without scaffolds. Central to these efforts is the prominent role that tissue engineering has in translating biological technology into clinical products; therefore, concomitant regulatory processes are also discussed.

Postgraduate Studies in the Field of HCI

NASA Astrophysics Data System (ADS)

Vainio, Teija; Surakka, Veikko; Raisamo, Roope; Räihä, Kari-Jouko; Isokoski, Poika; Väänänen-Vainio-Mattila, Kaisa; Kujala, Sari

In September of 2007, the Tampere Unit for Computer Human Interaction (TAUCHI) at the University of Tampere and The Unit of Human-Centered Technology (IHTE) at the Tampere University of Technology initiated a joint effort to increase collaboration in the field of human-technology interaction (HTI). One of the main aims was to develop higher quality education for university students and to carry out joint internationally recognized HTI research. Both research units have their own master and postgraduate students while the focus of education is at IHTE on usability and humancentered design of interactive products and services whereas TAUCHI focuses on human-technology interaction developing it by harmonizing the potential of technology with human abilities, needs, and limitations. Based on our joint analysis we know now that together TAUCHI and IHTE are offering an internationally competitive master’s program consisting of more than 40 basic, intermediate and advanced level courses. Although both units are partners in the national Graduate School in User- Centered Information Technology (UCIT) led by TAUCHI we have recognized a clear need for developing and systematizing our doctoral education.

The stock-flow model of spatial data infrastructure development refined by fuzzy logic.

PubMed

Abdolmajidi, Ehsan; Harrie, Lars; Mansourian, Ali

2016-01-01

The system dynamics technique has been demonstrated to be a proper method by which to model and simulate the development of spatial data infrastructures (SDI). An SDI is a collaborative effort to manage and share spatial data at different political and administrative levels. It is comprised of various dynamically interacting quantitative and qualitative (linguistic) variables. To incorporate linguistic variables and their joint effects in an SDI-development model more effectively, we suggest employing fuzzy logic. Not all fuzzy models are able to model the dynamic behavior of SDIs properly. Therefore, this paper aims to investigate different fuzzy models and their suitability for modeling SDIs. To that end, two inference and two defuzzification methods were used for the fuzzification of the joint effect of two variables in an existing SDI model. The results show that the Average-Average inference and Center of Area defuzzification can better model the dynamics of SDI development.

Joint Detect and Avoid Flight Testing

NASA Technical Reports Server (NTRS)

Maliska, Heather; Estrada, Ramon; Euteneuer, Eric; Gong, Chester; Arthur, Keith

2015-01-01

This presentation gives insight into a joint flight testing effort that included participation from NASA, Honeywell, and General Atomics. The presentation includes roles and responsibilities, test flow, and encounter requirements and summary.

Motor impairments related to brain injury timing in early hemiparesis. Part II: abnormal upper extremity joint torque synergies.

PubMed

Sukal-Moulton, Theresa; Krosschell, Kristin J; Gaebler-Spira, Deborah J; Dewald, Julius P A

2014-01-01

Extensive neuromotor development occurs early in human life, and the timing of brain injury may affect the resulting motor impairment. In Part I of this series, it was demonstrated that the distribution of weakness in the upper extremity depended on the timing of brain injury in individuals with childhood-onset hemiparesis. The goal of this study was to characterize how timing of brain injury affects joint torque synergies, or losses of independent joint control. Twenty-four individuals with hemiparesis were divided into 3 groups based on the timing of their injury: before birth (PRE-natal, n = 8), around the time of birth (PERI-natal, n = 8), and after 6 months of age (POST-natal, n = 8). Individuals with hemiparesis and 8 typically developing peers participated in maximal isometric shoulder, elbow, wrist, and finger torque generation tasks while their efforts were recorded by a multiple degree-of-freedom load cell. Motor output in 4 joints of the upper extremity was concurrently measured during 8 primary torque generation tasks to quantify joint torque synergies. There were a number of significant coupling patterns identified in individuals with hemiparesis that differed from the typically developing group. POST-natal differences were most noted in the coupling of shoulder abductors with elbow, wrist, and finger flexors, while the PRE-natal group demonstrated significant distal joint coupling with elbow flexion. The torque synergies measured provide indirect evidence for the use of bulbospinal pathways in the POST-natal group, while those with earlier injury may use relatively preserved ipsilateral corticospinal motor pathways.

Development of a Large Scale, High Speed Wheel Test Facility

NASA Technical Reports Server (NTRS)

Kondoleon, Anthony; Seltzer, Donald; Thornton, Richard; Thompson, Marc

1996-01-01

Draper Laboratory, with its internal research and development budget, has for the past two years been funding a joint effort with the Massachusetts Institute of Technology (MIT) for the development of a large scale, high speed wheel test facility. This facility was developed to perform experiments and carry out evaluations on levitation and propulsion designs for MagLev systems currently under consideration. The facility was developed to rotate a large (2 meter) wheel which could operate with peripheral speeds of greater than 100 meters/second. The rim of the wheel was constructed of a non-magnetic, non-conductive composite material to avoid the generation of errors from spurious forces. A sensor package containing a multi-axis force and torque sensor mounted to the base of the station, provides a signal of the lift and drag forces on the package being tested. Position tables mounted on the station allow for the introduction of errors in real time. A computer controlled data acquisition system was developed around a Macintosh IIfx to record the test data and control the speed of the wheel. This paper describes the development of this test facility. A detailed description of the major components is presented. Recently completed tests carried out on a novel Electrodynamic (EDS) suspension system, developed by MIT as part of this joint effort are described and presented. Adaptation of this facility for linear motor and other propulsion and levitation testing is described.

JSpOC Cognitive Task Analysis

NASA Astrophysics Data System (ADS)

Aleva, D.; McCracken, J.

This paper will overview a Cognitive Task Analysis (CTA) of the tasks accomplished by space operators in the Combat Operations Division (COD) of the Joint Space Operations Center (JSpOC). The methodology used to collect data will be presented. The work was performed in support of the AFRL Space Situation Awareness Fusion Intelligent Research Environment (SAFIRE) effort. SAFIRE is a multi-directorate program led by Air Force Research Laboratory (AFRL), Space Vehicles Directorate (AFRL/RV) and supporting Future Long Term Challenge 2.6.5. It is designed to address research areas identified from completion of a Core Process 3 effort for Joint Space Operations Center (JSpOC). The report is intended to be a resource for those developing capability in support of SAFIRE, the Joint Functional Component Command (JFCC) Space Integrated Prototype (JSIP) User-Defined Operating Picture (UDOP), and other related projects. The report is under distribution restriction; our purpose here is to expose its existence to a wider audience so that qualified individuals may access it. The report contains descriptions of the organization, its most salient products, tools, and cognitive tasks. Tasks reported are derived from the data collected and presented at multiple levels of abstraction. Recommendations for leveraging the findings of the report are presented. The report contains a number of appendices that amplify the methodology, provide background or context support, and includes references in support of cognitive task methodology. In a broad sense, the CTA is intended to be the foundation for relevant, usable capability in support of space warfighters. It presents, at an unclassified level, introductory material to familiarize inquirers with the work of the COD; this is embedded in a description of the broader context of the other divisions of the JSpOC. It does NOT provide guidance for the development of Tactics, Techniques, and Procedures (TT&Ps) in the development of JSpOC processes. However, the TT&Ps are a part of the structure of work, and are, therefore, a factor in developing future capability. The authors gratefully acknowledge the cooperation and assistance from the warfighters at the JSpOC as well as the personnel of the JSpOC Capabilities Integration Office (JCIO). Their input to the process created the value of this effort.

Nuclear propulsion technology development - A joint NASA/Department of Energy project

NASA Technical Reports Server (NTRS)

Clark, John S.

1992-01-01

NASA-Lewis has undertaken the conceptual development of spacecraft nuclear propulsion systems with DOE support, in order to establish the bases for Space Exploration Initiative lunar and Mars missions. This conceptual evolution project encompasses nuclear thermal propulsion (NTP) and nuclear electric propulsion (NEP) systems. A technology base exists for NTP in the NERVA program files; more fundamental development efforts are entailed in the case of NEP, but this option is noted to offer greater advantages in the long term.

Multimodality image display station

NASA Astrophysics Data System (ADS)

Myers, H. Joseph

1990-07-01

The Multi-modality Image Display Station (MIDS) is designed for the use of physicians outside of the radiology department. Connected to a local area network or a host computer, it provides speedy access to digitized radiology images and written diagnostics needed by attending and consulting physicians near the patient bedside. Emphasis has been placed on low cost, high performance and ease of use. The work is being done as a joint study with the University of Texas Southwestern Medical Center at Dallas, and as part of a joint development effort with the Mayo Clinic. MIDS is a prototype, and should not be assumed to be an IBM product.

Joining dissimilar materials using Friction Stir scribe technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upadhyay, Piyush; Hovanski, Yuri; Jana, Saumyadeep

2016-10-03

The ability to effectively join materials with vastly different melting points like Aluminum-Steel, Polymer composites - metals has been one of the road blocks in realizing multi-material components for light weighting efforts. Friction stir scribe (FSS) technique is a promising method that produces continuous overlap joint between materials with vastly different melting regimes and high temperature flow characteristics. FSS uses an offset cutting tool at the tip of the FSW pin to create an insitu mechanical interlock between material interfaces. With investments from Vehicle Technology office, US DOE and several automotive manufacturers and suppliers PNNL is developing the FSS processmore » and has demonstrated viability of joining several material combinations. Details of welding trails, unique challenges and mitigation strategies in different material combinations will be discussed. Joint characterization including mechanical tests and joint performances will also be presented.« less

Qualitative and quantitative descriptions of glenohumeral motion.

PubMed

Hill, A M; Bull, A M J; Wallace, A L; Johnson, G R

2008-02-01

Joint modelling plays an important role in qualitative and quantitative descriptions of both normal and abnormal joints, as well as predicting outcomes of alterations to joints in orthopaedic practice and research. Contemporary efforts in modelling have focussed upon the major articulations of the lower limb. Well-constrained arthrokinematics can form the basis of manageable kinetic and dynamic mathematical predictions. In order to contain computation of shoulder complex modelling, glenohumeral joint representations in both limited and complete shoulder girdle models have undergone a generic simplification. As such, glenohumeral joint models are often based upon kinematic descriptions of inadequate degrees of freedom (DOF) for clinical purposes and applications. Qualitative descriptions of glenohumeral motion range from the parody of a hinge joint to the complex realism of a spatial joint. In developing a model, a clear idea of intention is required in order to achieve a required application. Clinical applicability of a model requires both descriptive and predictive output potentials, and as such, a high level of validation is required. Without sufficient appreciation of the clinical intention of the arthrokinematic foundation to a model, error is all too easily introduced. Mathematical description of joint motion serves to quantify all relevant clinical parameters. Commonly, both the Euler angle and helical (screw) axis methods have been applied to the glenohumeral joint, although concordance between these methods and classical anatomical appreciation of joint motion is limited, resulting in miscommunication between clinician and engineer. Compounding these inconsistencies in motion quantification is gimbal lock and sequence dependency.

Analysis of postmarket complaints database for the iFuse SI Joint Fusion System®: a minimally invasive treatment for degenerative sacroiliitis and sacroiliac joint disruption

PubMed Central

Miller, Larry E; Reckling, W Carlton; Block, Jon E

2013-01-01

Background The sacroiliac joint is a common but under-recognized source of low back and gluteal pain. Patients with degenerative sacroiliitis or sacroiliac joint disruption resistant to nonsurgical treatments may undergo open surgery with sacroiliac joint arthrodesis, although outcomes are mixed and risks are significant. Minimally invasive sacroiliac joint arthrodesis was developed to minimize the risk of iatrogenic injury and to improve patient outcomes compared with open surgery. Methods Between April 2009 and January 2013, 5319 patients were treated with the iFuse SI Joint Fusion System® for conditions including sacroiliac joint disruption and degenerative sacroiliitis. A database was prospectively developed to record all complaints reported to the manufacturer in patients treated with the iFuse device. Complaints were collected through spontaneous reporting mechanisms in support of ongoing mandatory postmarket surveillance efforts. Results Complaints were reported in 204 (3.8%) patients treated with the iFuse system. Pain was the most commonly reported clinical complaint (n = 119, 2.2%), with nerve impingement (n = 48, 0.9%) and recurrent sacroiliac joint pain (n = 43, 0.8%) most frequently cited. All other clinical complaints were rare (≤0.2%). Ninety-six revision surgeries were performed in 94 (1.8%) patients at a median follow-up of four (range 0–30) months. Revisions were typically performed in the early postoperative period for treatment of a symptomatic malpositioned implant (n = 46, 0.9%) or to correct an improperly sized implant in an asymptomatic patient (n = 10, 0.2%). Revisions in the late postoperative period were performed to treat symptom recurrence (n = 34, 0.6%) or for continued pain of undetermined etiology (n = 6, 0.1%). Conclusion Analysis of a postmarket product complaints database demonstrates an overall low risk of complaints with the iFuse SI Joint Fusion System in patients with degenerative sacroiliitis or sacroiliac joint disruption. PMID:23761982

Analysis of postmarket complaints database for the iFuse SI Joint Fusion System®: a minimally invasive treatment for degenerative sacroiliitis and sacroiliac joint disruption.

PubMed

Miller, Larry E; Reckling, W Carlton; Block, Jon E

2013-01-01

The sacroiliac joint is a common but under-recognized source of low back and gluteal pain. Patients with degenerative sacroiliitis or sacroiliac joint disruption resistant to nonsurgical treatments may undergo open surgery with sacroiliac joint arthrodesis, although outcomes are mixed and risks are significant. Minimally invasive sacroiliac joint arthrodesis was developed to minimize the risk of iatrogenic injury and to improve patient outcomes compared with open surgery. Between April 2009 and January 2013, 5319 patients were treated with the iFuse SI Joint Fusion System® for conditions including sacroiliac joint disruption and degenerative sacroiliitis. A database was prospectively developed to record all complaints reported to the manufacturer in patients treated with the iFuse device. Complaints were collected through spontaneous reporting mechanisms in support of ongoing mandatory postmarket surveillance efforts. Complaints were reported in 204 (3.8%) patients treated with the iFuse system. Pain was the most commonly reported clinical complaint (n = 119, 2.2%), with nerve impingement (n = 48, 0.9%) and recurrent sacroiliac joint pain (n = 43, 0.8%) most frequently cited. All other clinical complaints were rare (≤0.2%). Ninety-six revision surgeries were performed in 94 (1.8%) patients at a median follow-up of four (range 0-30) months. Revisions were typically performed in the early postoperative period for treatment of a symptomatic malpositioned implant (n = 46, 0.9%) or to correct an improperly sized implant in an asymptomatic patient (n = 10, 0.2%). Revisions in the late postoperative period were performed to treat symptom recurrence (n = 34, 0.6%) or for continued pain of undetermined etiology (n = 6, 0.1%). Analysis of a postmarket product complaints database demonstrates an overall low risk of complaints with the iFuse SI Joint Fusion System in patients with degenerative sacroiliitis or sacroiliac joint disruption.

Cold Weather Wind Turbines: A Joint NASA/NSF/DOE Effort in Technology Transfer and Commercialization

NASA Technical Reports Server (NTRS)

Flynn, Michael; Bubenheim, David; Chiang, Erick; Goldman, Peter; Kohout, Lisa; Norton, Gary; Kliss, Mark (Technical Monitor)

1997-01-01

Renewable energy sources and their integration with other power sources to support remote communities is of interest for Mars applications as well as Earth communities. The National Science Foundation (NSF), NASA, and the Department of Energy (DOE) have been jointly supporting development of a 100 kW cold weather wind turbine through grants and SBIRs independently managed by each agency but coordinated by NASA. The NSF grant addressed issues associated with the South Pole application and a 3 kW direct drive unit is being tested there in anticipation of the 100 kW unit operation. The DOE-NREL contract focused on development of the 100 kW direct drive generator. The NASA SBIR focused on the development of the 100 kW direct drive wind turbine. The success of this effort has required coordination and team involvement of federal agencies and the industrial partners. Designs of the wind turbine and component performance testing results will be presented. Plans for field testing of wind turbines, based on this design, in village energy systems in Alaska and in energy production at the South Pole Station will be discussed. Also included will be a discussion of terrestrial and space use of hybrid energy systems, including renewable energy sources, such as the wind turbine, to support remote communities.

Design of an Advanced Wood Composite Rotor and Development of Wood Composite Blade Technology

NASA Technical Reports Server (NTRS)

Stroebel, Thomas; Dechow, Curtis; Zuteck, Michael

1984-01-01

In support of a program to advance wood composite wind turbine blade technology, a design was completed for a prototype, 90-foot diameter, two-bladed, one-piece rotor, with all wood/epoxy composite structure. The rotor was sized for compatibility with a generator having a maximum power rating of 4000 kilowatts. Innovative features of the rotor include: a teetering hub to minimize the effects of gust loads, untwisted blades to promote rotor power control through stall, joining of blades to the hub structure via an adhesive bonded structural joint, and a blade structural design which was simplified relative to earlier efforts. The prototype rotor was designed to allow flexibility for configuring the rotor upwind or downwind of the tower, for evaluating various types of teeter dampers and/or elastomeric stops, and with variable delta-three angle settings of the teeter shaft axis. The prototype rotor was also designed with provisions for installing pressure tap and angle of attack instrumentation in one blade. A production version rotor cost analysis was conducted. Included in the program were efforts directed at developing advanced load take-off stud designs for subsequent evaluation testing by NASA, development of aerodynamic tip brake concepts, exploratory testing of a wood/epoxy/graphite concept, and compression testing of wood/epoxy laminate, with scarf-jointed plies.

SUBTASK 6.1 – STRATEGIC STUDIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erickson, Thomas; Harju, John; Steadman, Edward

The Energy & Environmental Research Center (EERC) has recently completed 7 years of research through the Cooperative Agreement with the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) focused on fossil energy technology development and demonstration. To support a significant number of the different activities being considered within all of our research contracts with NETL, a subtask (6.1 – Strategic Studies) was created to focus on small research efforts that came up throughout the year that would support an existing EERC–NETL project or would help to develop a new concept for inclusion in future efforts. This subtask wasmore » funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FC26- 08NT43291« less

Direct Broadcast Satellite: Radio Program

NASA Astrophysics Data System (ADS)

Hollansworth, James E.

1992-10-01

NASA is committed to providing technology development that leads to the introduction of new commercial applications for communications satellites. The Direct Broadcast Satellite-Radio (DBS-R) Program is a joint effort between The National Aeronautics and Space Administration (NASA) and The United States Information Agency/Voice of America (USIA/VOA) directed at this objective. The purpose of this program is to define the service and develop the technology for a direct-to-listener satellite sound broadcasting system. The DBS-R Program, as structured by NASA and VOA, is now a three-phase program designed to help the U.S. commercial communications satellite and receiver industry bring about this new communications service. Major efforts are being directed towards frequency planning hardware and service development, service demonstration, and experimentation with new satellite and receiver technology.

Mine planning and emission control strategies using geostatistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martino, F.; Kim, Y.C.

1983-03-01

This paper reviews the past four years' research efforts performed jointly by the University of Arizona and the Homer City Owners in which geostatistics were applied to solve various problems associated with coal characterization, mine planning, and development of emission control strategies. Because geostatistics is the only technique which can quantify the degree of confidence associated with a given estimate (or prediction), it played an important role throughout the research efforts. Through geostatistics, it was learned that there is an urgent need for closely spaced sample information, if short-term coal quality predictions are to be made for mine planning purposes.

Can nurse practitioners and physicians beat parochialism into plowshares?

PubMed

Phillips, Robert L; Harper, Doreen C; Wakefield, Mary; Green, Larry A; Fryer, George E

2002-01-01

Nurse practitioners have evolved into a large and flexible workforce. Far too often, nurse practitioner and physician professional organizations do not work together but rather expend considerable effort jousting in policy arenas. Turf battles interfere with joint advocacy for needed health system change and delay development of interdisciplinary teams that could help patients. A combined, consistent effort is urgently needed for studying, training, and deploying a collaborative, integrated workforce aimed at improving the health care system of tomorrow. The country can ill afford doctors and nurses who ignore one another's capabilities and fail to maximize each other's contributions cost-effectively.

The Department of Defense Should Avoid a Joint Acquisition Approach to the Sixth-Generation Fighter

DTIC Science & Technology

2014-01-01

development, test, and evaluation (RDT&E) efforts and by achieving econo - mies of scale in procurement and operations and support (O&S).1 Yet, the need...subcomponents. • We assumed that single-service programs conduct com- pletely separate O&S and therefore do not enjoy econo - mies of scale in O&S. • We

Sensitive Equipment Decontamination

DTIC Science & Technology

2017-10-01

tomorrow’s CBRN threats. The document was elaborated by a group of scientists and CBRN specialists, all being members of the Hazard Management ... Management Panel within NATO Joint CBRN Defence Capability Development Group ii STO-TR-HFM-233 The NATO Science and Technology...accordance with NATO policies. The total spectrum of this collaborative effort is addressed by six Technical Panels who manage a wide range of scientific

A lumber grading system for the future: an update evaluation

Treesearch

D. Earl Kline; Chris Surak; Philip A. Araman

2000-01-01

Virginia Tech and the Southern Research Station of the USDA Forest Service have jointly developed and refined a multiple-sensor lumber-scanning prototype to demonstrate and test applicable scanning technologies (Conners et al. 1997, Kline et al. 1997, Kline et al. 1998). This R&D effort has led to a patented wood color and grain sorting system (Conners and Lu 1998...

Latin America Report.

DTIC Science & Technology

1985-08-09

They acknowledged the importance of tourism to promote the economic integra- tion and development of the two countries and stated their intention to...adopt measures aimed at increasing tourism through coordinated and joint efforts by national authorities. This work will be done by a commission to...6 [Article by Anthony Forbes] [Excerpts] FOREIGN and Tourism Minister Clement Maynard said today that the governments of the Bahamas and other

Connecticut permanent long-term bridge monitoring network, volume 5 : wireless monitoring of the hung span in a large truss bridge - I-95 NB over the Thames River in New London (bridge #3819).

DOT National Transportation Integrated Search

2014-08-01

This report describes the instrumentation and data acquisition for the center hung segment in the largest : truss bridge in Connecticut, located on the interstate system. The monitoring system was developed as a : joint effort between researchers at ...

Alternatives to Full-Depth Patching on Resurfacing Projects

DOT National Transportation Integrated Search

1993-09-01

The vast majority of Illinois' non-interstate network is constructed of jointed Portland cement concrete (PCC). Typically, Illinois' first significant rehabilitation efforts for jointed PCC pavements are in the form of full-depth bituminous concrete ...

The Power of Numbers: Transforming Birth Through Collaborations

PubMed Central

Hotelling, Barbara A.

2010-01-01

Collaborative efforts and coalitions have replaced exclusivity as birth organizations and individuals unite to humanize birth and provide women with transparency of information about maternity care providers and facilities and about access to the midwifery model of care. The Coalition for Improving Maternity Services and the upcoming 2010 “Mega Conference” to jointly celebrate the 50th anniversaries of Lamaze International and the International Childbirth Education Association serve as excellent examples of collaborative efforts to support natural, safe, and healthy birth practices as well as women's choices in childbirth. Childbirth educators are encouraged to learn from and support national coalitions devoted to improving maternity care and to use local resources to develop their own collaborative efforts on behalf of childbearing families. PMID:21358834

Innovative remote monitoring of plant health for environmental applications: A joint effort between EPCOT{reg_sign} and the DOE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robitaille, H.; Capelle, G.; Di Benedetto, J.

1996-12-31

In September of 1994, the US Department of Energy (DOE), Environmental Management, Office of Science and Technology for (OST) and Epcot{reg_sign} in the WALT DISNEY WORLD{reg_sign} Resort (Epcot) signed an agreement to cooperate on the research, development, and public communication and display of environmental technologies. Although Epcot and OST have distinctive missions, certain areas of their respective research and development efforts are common, including the integration of remote sensors with robotics platforms, airborne surveys for environmental characterization and monitoring, and ground based measurements of vegetation stress. The first area of cooperative R&D pursued under the agreement is the evaluation ofmore » laser-induced fluorescence imaging (LIFI), a technology developed by OST and proven effective for uranium detection. This paper describes the efforts being conducted under the Epcot-OST agreement and presents initial results. An appendix describing LIFI technology is also included.« less

Neural control of arm movements reveals a tendency to use gravity to simplify joint coordination rather than to decrease muscle effort.

PubMed

Wang, Wanyue; Dounskaia, Natalia

2016-12-17

How gravity influences neural control of arm movements remains under debate. We tested three alternative interpretations suggested by previous research: (1) that muscular control includes two components, tonic which compensates for gravity and phasic which produces the movement; (2) that there is a tendency to exploit gravity to reduce muscle effort; and (3) that there is a tendency to use a trailing pattern of joint control during which either the shoulder or elbow is rotated actively and the other joint rotates predominantly passively, and to exploit gravity for control of the passively rotated joint. A free-stroke drawing task was performed that required production of center-out strokes within a circle while selecting stroke directions randomly. The circle was positioned in the horizontal, sagittal, and frontal plane. The arm joints freely rotated in space. In each plane, the distribution of the strokes across directions was non-uniform. Directional histograms were built and their peaks were used to identify preferred movement directions. The directional preferences were especially pronounced in the two vertical planes. The upward directions were most preferred. To test the three interpretations, we used a kinetic analysis that determined the role of gravitational torque in the production of movement in the preferred directions. The results supported the third interpretation and provided evidence against the first and second interpretation. The trailing pattern has been associated with reduced neural effort for joint coordination, and therefore, we conclude that the major tendency with respect to gravity is to exploit it for simplification of joint coordination. Copyright © 2016 IBRO. Published by Elsevier Ltd. All rights reserved.

Proceedings of the Workshop on Government Oil Spill Modeling

NASA Technical Reports Server (NTRS)

Bishop, J. M. (Compiler)

1980-01-01

Oil spill model users and modelers were brought together for the purpose of fostering joint communication and increasing understanding of mutual problems. The workshop concentrated on defining user needs, presentations on ongoing modeling programs, and discussions of supporting research for these modeling efforts. Specific user recommendations include the development of an oil spill model user library which identifies and describes available models. The development of models for the long-term fate and effect of spilled oil was examined.

Brief report: reconstruction of joint hyaline cartilage by autologous progenitor cells derived from ear elastic cartilage.

PubMed

Mizuno, Mitsuru; Kobayashi, Shinji; Takebe, Takanori; Kan, Hiroomi; Yabuki, Yuichiro; Matsuzaki, Takahisa; Yoshikawa, Hiroshi Y; Nakabayashi, Seiichiro; Ik, Lee Jeong; Maegawa, Jiro; Taniguchi, Hideki

2014-03-01

In healthy joints, hyaline cartilage covering the joint surfaces of bones provides cushioning due to its unique mechanical properties. However, because of its limited regenerative capacity, age- and sports-related injuries to this tissue may lead to degenerative arthropathies, prompting researchers to investigate a variety of cell sources. We recently succeeded in isolating human cartilage progenitor cells from ear elastic cartilage. Human cartilage progenitor cells have high chondrogenic and proliferative potential to form elastic cartilage with long-term tissue maintenance. However, it is unknown whether ear-derived cartilage progenitor cells can be used to reconstruct hyaline cartilage, which has different mechanical and histological properties from elastic cartilage. In our efforts to develop foundational technologies for joint hyaline cartilage repair and reconstruction, we conducted this study to obtain an answer to this question. We created an experimental canine model of knee joint cartilage damage, transplanted ear-derived autologous cartilage progenitor cells. The reconstructed cartilage was rich in proteoglycans and showed unique histological characteristics similar to joint hyaline cartilage. In addition, mechanical properties of the reconstructed tissues were higher than those of ear cartilage and equal to those of joint hyaline cartilage. This study suggested that joint hyaline cartilage was reconstructed from ear-derived cartilage progenitor cells. It also demonstrated that ear-derived cartilage progenitor cells, which can be harvested by a minimally invasive method, would be useful for reconstructing joint hyaline cartilage in patients with degenerative arthropathies. © AlphaMed Press.

Multilateral Biomedical Data Sharing in the One-year Joint US-Russian Mission on the International Space Station

NASA Technical Reports Server (NTRS)

Charles, John B.; Haven, C.; Johnson-Throop, K.; Van Baalen, M.; McFather, J.

2014-01-01

The One Year Mission (1YM) by two astronauts on the International Space Station (ISS), starting in March 2015, offers a unique opportunity to expand multilateral collaboration by sharing data and resources among the partner agencies in preparation for planned space exploration missions beyond low Earth orbit. Agreements and protocols will be established for the collection, distribution, analysis and reporting of both research and clinical data. Data will be shared between the agencies sponsoring the investigators, and between the research and clinical medicine communities where common interests are identified. The assignment of only two astronauts, one Russian and the other American, to the 1YM necessitated creativity in bilateral efforts to maximize the biomedical return from the opportunity. Addition of Canadian, European and Japanese investigations make the effort even more integrative. There will be three types of investigations: joint, cross-participation and data-exchange. The joint investigations have US and Russian coprincipal investigators, and the data acquired will be their common responsibility. The other two types must develop data sharing agreements and processes specific to their needs. A multilateral panel of ISS partner space agencies will develop policies for international exchange of scientific information to meet their science objectives and priorities. They will promote archiving of space flight data and will inform each other and the scientific community at large about the results obtained from space life sciences studies. Integration tasks for the 1YM are based on current experience from the ISS and previous efforts on the Russian space station Mir. Closer coordination between international partners requires more common approaches to remove barriers to multilateral resource utilization on the ISS. Greater integration in implementation should increase utilization efficiency to benefit all participants in spaceflight human research. This presentation will describe the overarching principles for multilateral data collection, analysis and sharing and for data security for medical and research data shared between ISS partners prior to release in public forums.

Collaborative engagement experiment

NASA Astrophysics Data System (ADS)

Mullens, Katherine; Troyer, Bradley; Wade, Robert; Skibba, Brian; Dunn, Michael

2006-05-01

Unmanned ground and air systems operating in collaboration have the potential to provide future Joint Forces a significant capability for operations in complex terrain. Collaborative Engagement Experiment (CEE) is a consolidation of separate Air Force, Army and Navy collaborative efforts within the Joint Robotics Program (JRP) to provide a picture of the future of unmanned warfare. The Air Force Research Laboratory (AFRL), Material and Manufacturing Directorate, Aerospace Expeditionary Force Division, Force Protection Branch (AFRL/MLQF), The Army Aviation and Missile Research, Development and Engineering Center (AMRDEC) Joint Technology Center (JTC)/Systems Integration Laboratory (SIL), and the Space and Naval Warfare Systems Center - San Diego (SSC San Diego) are conducting technical research and proof of principle experiments for an envisioned operational concept for extended range, three dimensional, collaborative operations between unmanned systems, with enhanced situational awareness for lethal operations in complex terrain. This paper describes the work by these organizations to date and outlines some of the plans for future work.

Science and Technology in Japan -- A Brief Analytic Survey

DTIC Science & Technology

1975-11-01

international cross- licensing agreements, participation in international joint research efforts, and the growing list of Japanese scientific and...licensing has also increased, and Japanese companies have undertaken joint research with U.S. companies. There have been a few well-publicized... joint ventures, and market restrictions on the licensee may become increasingly onerous. One detects a reluctance among some U.S. companies to

Development of an MR-compatible hand exoskeleton that is capable of providing interactive robotic rehabilitation during fMRI imaging.

PubMed

Kim, Sangjoon J; Kim, Yeongjin; Lee, Hyosang; Ghasemlou, Pouya; Kim, Jung

2018-02-01

Following advances in robotic rehabilitation, there have been many efforts to investigate the recovery process and effectiveness of robotic rehabilitation procedures through monitoring the activation status of the brain. This work presents the development of a two degree-of-freedom (DoF) magnetic resonance (MR)-compatible hand device that can perform robotic rehabilitation procedures inside an fMRI scanner. The device is capable of providing real-time monitoring of the joint angle, angular velocity, and joint force produced by the metacarpophalangeal (MCP) and proximal interphalangeal (PIP) joints of four fingers. For force measurement, a custom reflective optical force sensor was developed and characterized in terms of accuracy error, hysteresis, and repeatability in the MR environment. The proposed device consists of two non-magnetic ultrasonic motors to provide assistive and resistive forces to the MCP and PIP joints. With actuation and sensing capabilities, both non-voluntary-passive movements and active-voluntary movements can be implemented. The MR compatibility of the device was verified via the analysis of the signal-to-noise ratio (SNR) of MR images of phantoms. SNR drops of 0.25, 2.94, and 11.82% were observed when the device was present but not activated, when only the custom force sensor was activated, and when both the custom force sensor and actuators were activated, respectively.

Triple Track: A New Paradigm for Developing Air Force Officers

DTIC Science & Technology

2017-03-06

multiple career fields, including aircraft maintenance, command and control, engineering , modeling analysis, joint targeting, program management...the opportunity for an engineering job because he was too critical in his career field. The member ultimately left the service.41 Critical manning...manpower, and officer training. Over the course of her career , she was responsible for generating over 956 C-130 aircraft sorties, led interagency efforts

Antibody repertoire development in fetal and neonatal piglets. XXII. Lambda rearrangement precedes kappa rearrangement during B-cell lymphogenesis in swine

USDA-ARS?s Scientific Manuscript database

PCR was used to detect VDJ and VJ rearrangement, expression of RAG-1, TdT and VpreB and the presence of signal joint circles (SJC) in an effort to identify sites of B cell lymphogenesis in tissue lysates and sorted leukocytes of fetal and newborn piglets. VDJ, VlambdaJlambda but not VkappaJkappa re...

2+2 Electronics Technology. Looking Forward to the Future. A Model Secondary/Post-Secondary 2+2 Program To Prepare Students for Employment.

ERIC Educational Resources Information Center

Judson Independent School District, Converse, TX.

This document contains all pertinent information and essential background data necessary to implement the 2+2 electronics program at the high school level. An introduction describes development of the electronics technology 2+2 project that was a joint effort among San Antonio College and Judson, Northside, and North East Independent School…

Not Schools Alone: Guidelines for Schools and Communities To Prevent the Use of Tobacco, Alcohol, and Other Drugs among Children and Youth.

ERIC Educational Resources Information Center

California State Dept. of Education, Sacramento.

Although schools have the primary responsibility for educating children and adolescents, schools alone cannot prevent the use of tobacco, alcohol, and other drugs. Preventing youth from smoking, drinking, and using drugs must be a collaborative effort, jointly undertaken by the school, community, and youths themselves. This guide was developed to…

An Assessment of Joint Chat Requirements From Current Usage Patterns

DTIC Science & Technology

2006-06-01

Army Special Forces firebases always had SATCOM connectivity with the text 35 messaging capability running and most business within the firebases was...overreact, or proactive action on bad information, and points to the need for good business rules. Some, organizations, like USCENTAF, have already...developed chat business rules. Users like how chat facilitates understanding with written text. Time and effort is saved from repeating questions

Open Innovation and Technology Maturity Analysis

DTIC Science & Technology

2007-09-11

Management Process Develop a framework which incorporates DoD Acquisition Management framework (e.g: TRLs), DoD Business Transformation strategies...Public Organizations (DoD): DoD Force Transformation : • Support the Joint Warfighting Capability of the DoD • Enable Rapid Access to Information for...Survey - 2007  Defense Transformation : Clear Leadership, Accountability, and Management Tools Are Needed to Enhance DOD’s Efforts to Transform Military

The Development of Mobile Augmented Reality

DTIC Science & Technology

2012-01-01

working jointly with NRL, performed a domain analysis ( Gabbard et al., 2002) to create a context for usability engineering effort, performed formative...rectangle to provide a background enabled the fastest user performance ( Gabbard et al., 2007). Tracking the user’s head position relative to the real...thank Yohan Baillot, Reinhold Behringer, Blaine Bell, Dennis Brown, Aaron Bryden, Enylton Coelho, Elliot Cooper-Balis, Deborah Hix, Joseph Gabbard

Environmental Action and Student Environmental Leaders: Exploring the Influence of Environmental Attitudes, Locus of Control, and Sense of Personal Responsibility

ERIC Educational Resources Information Center

Ernst, Julie; Blood, Nathaniel; Beery, Thomas

2017-01-01

The Student Climate and Conservation Congress (SC3) is a joint educational effort between the United States Fish and Wildlife Service and the Green Schools Alliance that aims to develop the next generation of conservation leaders through fostering action competence in youth. Data from SC3 participants was used to investigate four predictors of…

The Midland fiber-optic analog transmission system development project (FATS)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baumgart, J.S.; Anaya, R.; Morris, G.

1988-07-01

This report was written to document the overall effort related to the development and testing of the various components comprising the fiber optic analog transmission system (FATS) and to the validation of the FATS itself. The overall project was approached as a joint effort between the Los Alamos National Laboratory; the Atomic Weapons Research Establishment (AWRE); and EGandG Energy Measurements. The ultimate goal of the project was to develop a system, based on laser diodes and a streak camera system, to measure alpha. Although the FATS was not fielded on the MIDLAND event, in the course of the project wemore » did in fact answer technology questions identified on previous experiments and develop a better understanding of system needs. We hope that the information contained in this report will provide a basis for planning future experiments, as well as defining the direction for additional laboratory measurements. 94 figs.« less

Integrated automation for manufacturing of electronic assemblies

NASA Technical Reports Server (NTRS)

Sampite, T. Joseph

1991-01-01

Since 1985, the Naval Ocean Systems Center has been identifying and developing needed technology for flexible manufacturing of hybrid microelectronic assemblies. Specific projects have been accomplished through contracts with manufacturing companies, equipment suppliers, and joint efforts with other government agencies. The resulting technology has been shared through semi-annual meetings with government, industry, and academic representatives who form an ad hoc advisory panel. More than 70 major technical capabilities have been identified for which new development is needed. Several of these developments have been completed and are being shared with industry.

Satellite Power System (SPS) FY 79 program summary

NASA Technical Reports Server (NTRS)

1980-01-01

The Satellite Power System (SPS) program a joint effort to develop an initial understanding of the technical feasibility, the economic practicality, and the social and environmental acceptability of the SPS concept is discussed. This is being accomplished through implementation of the Concept Development and Evaluation Program Plan which is scheduled for completion by the end of FY 1980. This Program Summary not only covers FY 1979 but includes work completed in FY 1977 and FY 1978 in order to give a comprehensive picture of the DOE involvement in the SPS concept development and evaluation process.

Environmental Public Health Survelliance for Exposure to Respiratory Health Hazards: A Joint NASA/CDC Project to Use Remote Sensing Data for Estimating Airborne Particulate Matter Over the Atlanta, Georgia Metropolitan Area

NASA Technical Reports Server (NTRS)

Quattrochi, Dale A.; Rickman, Douglas; Mohammad, Al-Hamdan; Crosson, William; Estes, Maurice, Jr.; Limaye, Ashutosh; Qualters, Judith

2008-01-01

Describes the public health surveillance efforts of NASA, in a joint effort with the Center for Disease Control (CDC). NASA/MSFC and the CDC are partners in linking nvironmental and health data to enhance public health surveillance. The use of NASA technology creates value - added geospatial products from existing environmental data sources to facilitate public health linkages. The venture sought to provide remote sensing data for the 5-country Metro-Atlanta area and to integrate this environmental data with public health data into a local network, in an effort to prevent and control environmentally related health effects. Remote sensing data used environmental data (Environmental Protection Agency [EPA] Air Quality System [AQS] ground measurements and MODIS Aerosol Optical Depth [AOD]) to estimate airborne particulate matter over Atlanta, and linked this data with health data related to asthma. The study proved the feasibility of linking environmental data (MODIS particular matter estimates and AQS) with health data (asthma). Algorithms were developed for QC, bias removal, merging MODIS and AQS particulate matter data, as well as for other applications. Additionally, a Business Associate Agreement was negotiated for a health care provider to enable sharing of Protected Health Information.

Environmental assessment and exposure reduction of cockroaches: A practice parameter

PubMed Central

Portnoy, Jay; Chew, Ginger L.; Phipatanakul, Wanda; Williams, P. Brock; Grimes, Carl; Kennedy, Kevin; Matsui, Elizabeth C.; Miller, J. David; Bernstein, David; Blessing-Moore, Joann; Cox, Linda; Khan, David; Lang, David; Nicklas, Richard; Oppenheimer, John; Randolph, Christopher; Schuller, Diane; Spector, Sheldon; Tilles, Stephen A.; Wallace, Dana; Seltzer, James; Sublett, James

2013-01-01

This parameter was developed by the Joint Task Force on Practice Parameters, representing the American Academy of Allergy, Asthma & Immunology (AAAAI); the American College of Allergy, Asthma & Immunology (ACAAI); and the joint Council of Allergy, Asthma & Immunology. The AAAAI and the ACAAI have jointly accepted responsibility for establishing “Environmental assessment and remediation: a practice parameter.” This is a complete and comprehensive document at the current time. The medical environment is a changing environment, and not all recommendations will be appropriate for all patients. Because this document incorporated the efforts of many participants, no single person, including those who served on the Joint Task Force, is authorized to provide an official AAAAI or ACAAI interpretation of these practice parameters. Any request for information about or an interpretation of these practice parameters by the AAAAI or ACAAI should be directed to the Executive Offices of the AAAAI, the ACAAI, and the Joint Council of Allergy, Asthma & Immunology. These parameters are not designed for use by pharmaceutical companies in drug promotion. The findings and conclusions in this manuscript are those of the authors and do not necessarily represent the official position of the Centers for Disease Control and Prevention (CDC). PMID:23938214

Joint Program Management Handbook

DTIC Science & Technology

1994-12-01

service networks , and unique requirements, such as in the special opeations area, require a special effort by joint program managers Figure 3-3...the Engieermg and Manufacuring Devopment Phase. Nfilestoae HI- Develommen Annros Devopment approval marks a significant step for any program, but it is

Real-time multisensor data fusion for target detection, classification, tracking, counting, and range estimates

NASA Astrophysics Data System (ADS)

Tsui, Eddy K.; Thomas, Russell L.

2004-09-01

As part of the Commanding General of Army Material Command's Research, Development & Engineering Command (RDECOM), the U.S. Army Research Development and Engineering Center (ARDEC), Picatinny funded a joint development effort with McQ Associates, Inc. to develop an Advanced Minefield Sensor (AMS) as a technology evaluation prototype for the Anti-Personnel Landmine Alternatives (APLA) Track III program. This effort laid the fundamental groundwork of smart sensors for detection and classification of targets, identification of combatant or noncombatant, target location and tracking at and between sensors, fusion of information across targets and sensors, and automatic situation awareness to the 1st responder. The efforts have culminated in developing a performance oriented architecture meeting the requirements of size, weight, and power (SWAP). The integrated digital signal processor (DSP) paradigm is capable of computing signals from sensor modalities to extract needed information within either a 360° or fixed field of view with acceptable false alarm rate. This paper discusses the challenges in the developments of such a sensor, focusing on achieving reasonable operating ranges, achieving low power, small size and low cost, and applications for extensions of this technology.

Technologies for Nondestructive Evaluation of Surfaces and Thin Coatings

NASA Technical Reports Server (NTRS)

1999-01-01

The effort included in this project included several related activities encompassing basic understanding, technological development, customer identification and commercial transfer of several methodologies for nondestructive evaluation of surfaces and thin surface coatings. Consistent with the academic environment, students were involved in the effort working with established investigators to further their training, provide a nucleus of experienced practitioners in the new technologies during their industrial introduction, and utilize their talents for project goals. As will be seen in various portions of the report, some of the effort has led to commercialization. This process has spawned other efforts related to this project which are supported from outside sources. These activities are occupying the efforts of some of the people who were previously supported within this grant and its predecessors. The most advanced of the supported technologies is thermography, for which the previous joint efforts of the investigators and NASA researchers have developed several techniques for extending the utility of straight thermographic inspection by producing methods of interpretation and analysis accessible to automatic image processing with computer data analysis. The effort reported for this technology has been to introduce the techniques to new user communities, who are then be able to add to the effective uses of existing products with only slight development work. In a related development, analysis of a thermal measurement situation in past efforts led to a new insight into the behavior of simple temperature probes. This insight, previously reported to the narrow community in which the particular measurement was made, was reported to the community of generic temperature measurement experts this year. In addition to the propagation of mature thermographic techniques, the development of a thermoelastic imaging system has been an important related development. Part of the work carried out in the effort reported here has been to prepare reports introducing the newly commercially available thermoelastic measurements to the appropriate user communities.

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

NASA Technical Reports Server (NTRS)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

Assessing rangelands

USGS Publications Warehouse

Pyke, David A.

2002-01-01

It is important for land managers and technical assistance specialists to be able to assess the health of rangelands in order to know where to focus management efforts. The complexity of ecological processes, and the inherent expense of directly measuring site integrity, suggests a need for an evaluation process that focuses instead on biological and physical attributes. In a collaborative effort, the USGS, ARS, BLM, and NRCS have jointly developed a system in which 17 indicators are used to gauge three attributes of rangeland health. A qualitative, observational procedure provides an assessment of the functional status of these indicators. This quick assessment technique, by providing an understanding about each attribute, helps interpret rangeland health.

The Meeting of the Americas

NASA Astrophysics Data System (ADS)

Bates, John; Fucugauchi, Jaime Urrutia

2008-05-01

The AGU Joint Assembly, previously known as the Spring Meeting, has formally adopted the designation ``The Meeting of the Americas.'' This designation reflects the objective of the Joint Assembly to promote cooperative efforts among Earth and science societies in the Americas. To achieve this objective, future Joint Assembly locations will rotate among different cities in the United States, Canada, and Latin America; the Program Committee includes representatives from throughout the Americas; and the meetings will be convened jointly with scientific societies throughout the Americas.

Joint implementation: Biodiversity and greenhouse gas offsets

NASA Astrophysics Data System (ADS)

Cutright, Noel J.

1996-11-01

One of the most pressing environmental issues today is the possibility that projected increases in global emissions of greenhouse gases from increased deforestation, development, and fossil-fuel combustion could significantly alter global climate patterns. Under the terms of the United Nations Framework Convention on Climate Change, signed in Rio de Janeiro during the June 1992 Earth Summit, the United States and other industrialized countries committed to balancing greenhouse gas emissions at 1990 levels in the year 2000. Included in the treaty is a provision titled “Joint Implementation,” whereby industrialized countries assist developing countries in jointly modifying long-term emission trends, either through emission reductions or by protecting and enhancing greenhouse gas sinks (carbon sequestration). The US Climate Action Plan, signed by President Clinton in 1993, calls for voluntary climate change mitigation measures by various sectors, and the action plan included a new program, the US Initiative on Joint Implementation. Wisconsin Electric decided to invest in a Jl project because its concept encourages creative, cost-effective solutions to environmental problems through partnering, international cooperation, and innovation. The project chosen, a forest preservation and management effort in Belize, will sequester more than five million tons of carbon dioxide over a 40-year period, will become economically selfsustaining after ten years, and will have substantial biodiversity benefits.

Laser-based rework in electronics production

NASA Astrophysics Data System (ADS)

Albert, Florian; Mys, Ihor; Schmidt, Michael

2007-02-01

Despite the electronic manufacturing is well-established mass production process for a long time, the problem of reworking, i.a. reject and replace of defect components, still exists. The rework operations (soldering, replacement and desoldering) are performed in most cases manually. However, this practice is characterized by an inconsistent quality of the reworked solder joints and a high degree of physiological stress for the employees. In this paper, we propose a novel full-automated laser based soldering and rework process. Our developed soldering system is a pick-and-place unit with an integrated galvanometer scanner, a fiber coupled diode laser for quasi-simultaneous soldering and a pyrometer-based process control. The developed system provides soldering and reworking processes taking into account a kind of defect, a type of electronic component and quality requirements from the IPC- 610 norm. The paper spends a great deal of efforts to analyze quality of laser reworked solder joints. The quality depends mainly on the type and thickness of intermetallic phases between solder, pads and leads; the wetting angles between pad, solder and lead; and finally, the joint microstructure with its mechanical properties. The influence of the rework soldering on these three factors is discussed and compared to conventional laser soldering results. In order to optimize the quality of reworked joints, the different strategies of energy input are applied.

Structural health management of aerospace hotspots under fatigue loading

NASA Astrophysics Data System (ADS)

Soni, Sunilkumar

Sustainability and life-cycle assessments of aerospace systems, such as aircraft structures and propulsion systems, represent growing challenges in engineering. Hence, there has been an increasing demand in using structural health monitoring (SHM) techniques for continuous monitoring of these systems in an effort to improve safety and reduce maintenance costs. The current research is part of an ongoing multidisciplinary effort to develop a robust SHM framework resulting in improved models for damage-state awareness and life prediction, and enhancing capability of future aircraft systems. Lug joints, a typical structural hotspot, were chosen as the test article for the current study. The thesis focuses on integrated SHM techniques for damage detection and characterization in lug joints. Piezoelectric wafer sensors (PZTs) are used to generate guided Lamb waves as they can be easily used for onboard applications. Sensor placement in certain regions of a structural component is not feasible due to the inaccessibility of the area to be monitored. Therefore, a virtual sensing concept is introduced to acquire sensor data from finite element (FE) models. A full three dimensional FE analysis of lug joints with piezoelectric transducers, accounting for piezoelectrical-mechanical coupling, was performed in Abaqus and the sensor signals were simulated. These modeled sensors are called virtual sensors. A combination of real data from PZTs and virtual sensing data from FE analysis is used to monitor and detect fatigue damage in aluminum lug joints. Experiments were conducted on lug joints under fatigue loads and sensor signals collected were used to validate the simulated sensor response. An optimal sensor placement methodology for lug joints is developed based on a detection theory framework to maximize the detection rate and minimize the false alarm rate. The placement technique is such that the sensor features can be directly correlated to damage. The technique accounts for a number of factors, such as actuation frequency and strength, minimum damage size, damage detection scheme, material damping, signal to noise ratio and sensing radius. Advanced information processing methodologies are discussed for damage diagnosis. A new, instantaneous approach for damage detection, localization and quantification is proposed for applications to practical problems associated with changes in reference states under different environmental and operational conditions. Such an approach improves feature extraction for state awareness, resulting in robust life prediction capabilities.

Beyond Coordination: Joint Planning and Program Execution. The IHPRPT Materials Working Group

NASA Technical Reports Server (NTRS)

Stropki, Michael A.; Cleyrat, Danial A.; Clinton, Raymond G., Jr.; Rogacki, John R. (Technical Monitor)

2000-01-01

"Partnership is more than just coordination," stated then-Commander of the Air Force Research Laboratory (AFRL), Major General Dick Paul (USAF-Ret), at this year's National Space and Missile Materials Symposium. His comment referred to the example of the joint planning and program execution provided by the Integrated High Payoff Rocket Propulsion Technology (IHPRPT) Materials Working Group (IMWG). Most people agree that fiscal pressures imposed by shrinking budgets have made it extremely difficult to build upon our existing technical capabilities. In times of sufficient budgets, building advanced systems poses no major difficulties. However, with today's budgets, realizing enhanced capabilities and developing advanced systems often comes at an unaffordable cost. Overcoming this problem represents both a challenge and an opportunity to develop new business practices that allow us to develop advanced technologies within the restrictions imposed by current funding levels. Coordination of technology developments between different government agencies and organizations is a valuable tool for technology transfer. However, rarely do the newly developed technologies have direct applicability to other ongoing programs. Technology requirements are typically determined up-front during the program planning stage so that schedule risk can be minimized. The problem with this process is that the costs associated with the technology development are often borne by a single program. Additionally, the potential exists for duplication of technical effort. Changing this paradigm is a difficult process but one that can be extremely worthwhile should the right opportunity arise. The IMWG is one such example where NASA, the DoD, and industry have developed joint requirements that are intended to satisfy multiple program needs. More than mere coordination, the organizations comprising the group come together as partners, sharing information and resources, proceeding from a joint roadmap.

Long-Term Durability Analysis of a 100,000+ Hr Stirling Power Convertor Heater Head

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.; Bowman, Randy R.; Krause, David L.; Halford, Gary R.

2000-01-01

DOE and NASA have identified Stirling Radioisotope Power Systems (SRPS) as the power supply for deep space exploration missions the Europa Orbiter and Solar Probe. As a part of this effort, NASA has initiated a long-term durability project for critical hot section components of the Stirling power convertor to qualify flight hardware. This project will develop a life prediction methodology that utilizes short-term (t < 20,000 hr) test data to verify long-term (t > 100,000 hr) design life. The project consists of generating a materials database for the specific heat of alloy, evaluation of critical hermetic sealed joints, life model characterization, and model verification. This paper will describe the qualification methodology being developed and provide a status for this effort.

On-Line Enrichment Monitor (OLEM) Phase II Final Report Techniques and Equipment for Safeguards at Gas Centrifuge Enrichment Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Younkin, James R.; Garner, James R.

2017-04-01

Over the last five years, OLEM has been a collaborative development effort involving the IAEA, LANL, ORNL, URENCO, and the NNSA. The collective team has completed the following: design and modelling, software development, hardware integration, testing with the ORNL UF6 Flow Loop, a field trial at the Urenco facility in Almelo, the Netherlands, and a Demonstration at the Urenco USA facility in Eunice, New Mexico. This combined effort culminated in the deployment of several OLEM collection nodes in Iran. These OLEM units are one unattended monitoring system component of the Joint Comprehensive Plan of Action allowing the International Atomic Energymore » Agency to verify Iran’s compliance with the enrichment production aspects of the agreement.« less

A unified motion planning approach for redundant and non-redundant manipulators with actuator constraints. Ph.D. Thesis Final Report

NASA Technical Reports Server (NTRS)

Chung, Ching-Luan

1990-01-01

The term trajectory planning has been used to refer to the process of determining the time history of joint trajectory of each joint variable corresponding to a specified trajectory of the end effector. The trajectory planning problem was solved as a purely kinematic problem. The drawback is that there is no guarantee that the actuators can deliver the effort necessary to track the planned trajectory. To overcome this limitation, a motion planning approach which addresses the kinematics, dynamics, and feedback control of a manipulator in a unified framework was developed. Actuator constraints are taken into account explicitly and a priori in the synthesis of the feedback control law. Therefore the result of applying the motion planning approach described is not only the determination of the entire set of joint trajectories but also a complete specification of the feedback control strategy which would yield these joint trajectories without violating actuator constraints. The effectiveness of the unified motion planning approach is demonstrated on two problems which are of practical interest in manipulator robotics.

Load emphasizes muscle effort minimization during selection of arm movement direction

PubMed Central

2012-01-01

Background Directional preferences during center-out horizontal shoulder-elbow movements were previously established for both the dominant and non-dominant arm with the use of a free-stroke drawing task that required random selection of movement directions. While the preferred directions were mirror-symmetrical in both arms, they were attributed to a tendency specific for the dominant arm to simplify control of interaction torque by actively accelerating one joint and producing largely passive motion at the other joint. No conclusive evidence has been obtained in support of muscle effort minimization as a contributing factor to the directional preferences. Here, we tested whether distal load changes directional preferences, making the influence of muscle effort minimization on the selection of movement direction more apparent. Methods The free-stroke drawing task was performed by the dominant and non-dominant arm with no load and with 0.454 kg load at the wrist. Motion of each arm was limited to rotation of the shoulder and elbow in the horizontal plane. Directional histograms of strokes produced by the fingertip were calculated to assess directional preferences in each arm and load condition. Possible causes for directional preferences were further investigated by studying optimization across directions of a number of cost functions. Results Preferences in both arms to move in the diagonal directions were revealed. The previously suggested tendency to actively accelerate one joint and produce passive motion at the other joint was supported in both arms and load conditions. However, the load increased the tendency to produce strokes in the transverse diagonal directions (perpendicular to the forearm orientation) in both arms. Increases in required muscle effort caused by the load suggested that the higher frequency of movements in the transverse directions represented increased influence of muscle effort minimization on the selection of movement direction. This interpretation was supported by cost function optimization results. Conclusions While without load, the contribution of muscle effort minimization was minor, and therefore, not apparent, the load revealed this contribution by enhancing it. Unlike control of interaction torque, the revealed tendency to minimize muscle effort was independent of arm dominance. PMID:23035925

Test results for composite specimens and elements containing joints and cutouts

NASA Technical Reports Server (NTRS)

Sumida, P. T.; Madan, R. C.; Hawley, A. V.

1988-01-01

A program was conducted to develop the technology for joints and cutouts in a composite fuselage that meets all design requirements of a large transport aircraft for the 1990s. An advanced trijet derivative of the DC-10 was selected as the baseline aircraft. Design and analysis of a 30-foot-long composite fuselage barrel provided a realistic basis for the test effort. The primary composite material was Hexcel F584 resin on 12 K IM6 fiber, in tape and broadgoods form. Fiberglass broadgoods were used in E-glass and S-glass fiber form in the cutout region of some panels. Additionally, injection-molded chopped graphite fiber/PEEK was used for longeron-to-frame shear clips. The test effort included four groups of test specimens, beginning with coupon specimens of mono-layer and cross-piled laminates, progressing through increasingly larger and more complex specimens, and ending with two 4- by 5-foot curved fuselage side panels. One of the side panels incorporated a transverse skin splice, while the second included two cabin window cutouts.

Efficient Kinematic Computations For 7-DOF Manipulators

NASA Technical Reports Server (NTRS)

Seraji, Homayoun; Long, Mark K.; Kreutz-Delgado, Kenneth

1994-01-01

Efficient algorithms for forward kinematic mappings of seven-degree-of-freedom (7-DOF) robotic manipulator having revolute joints developed on basis of representation of redundant DOF in terms of parameter called "arm angle." Continuing effort to exploit redundancy in manipulator according to concept of basic and additional tasks. Concept also discussed in "Configuration-Control Scheme Copes With Singularities" (NPO-18556) and "Increasing the Dexterity of Redundant Robots" (NPO-17801).

Always Strategic: Jointly Essential Landpower

DTIC Science & Technology

2015-02-01

United States Army War College’s lines of effort to educate strategic leaders and provide well-being education and support by developing self ...wartime mobilization, there is no doubt that it cannot properly be assessed as being even some- what equal in national cultural esteem to the military...apparent- ly more than marginally like ideas, such as seapower, airpower, and cyberpower. For obvious, and indeed all but self -evident reasons with

Liquid Annular Seal Research

NASA Technical Reports Server (NTRS)

Palazzolo, Alan B.; Venkataraman, Balaji; Padavala, Sathya S.; Ryan, Steve; Vallely, Pat; Funston, Kerry

1996-01-01

This paper highlights the accomplishments on a joint effort between NASA - Marshall Space Flight Center and Texas A and M University to develop accurate seal analysis software for use in rocket turbopump design, design audits and trouble shooting. Results for arbitrary clearance profile, transient simulation, thermal effects solution and flexible seal wall model are presented. A new solution for eccentric seals based on cubic spline interpolation and ordinary differential equation integration is also presented.

The special effort processing of FGGE data

NASA Technical Reports Server (NTRS)

1983-01-01

The basic FGGE level IIb data set was enhanced. It focused on removing deficiencies in the objective methods of quality assurance, removing efficiencies in certain types of operationally produced satellite soundings, and removing deficiencies in certain types of operationally produced cloud tracked winds. The Special Effort was a joint NASA-NOAA-University of Wisconsin effort. The University of Wisconsin installed an interactive McIDAS capability on the Amdahl computer at the Goddard Laboratory of Atmospheric Sciences (GLAS) with one interactive video terminal at Goddard and the other at the World Weather Building. With this interactive capability a joint processing effort was undertaken to reprocess certain FGGE data sets. NOAA produced a specially edited data set for the special observing periods (SOPs) of FGGE. NASA produced an enhanced satellite sounding data set for the SOPs while the University of Wisconsin produced an enhanced cloud tracked wind set from the Japanese geostationary satellite images.

Full-depth repair of jointed PCC pavements cast-in-place and precast procedures.

DOT National Transportation Integrated Search

1976-01-01

The deterioration of jointed portland cement concrete (PCC) pavements on the interstate system in Virginia has created a need for full-depth and partial-depth repairs. In this report, efforts related to full-depth repairs are described and discussed,...

Experimental Evaluation and Workload Characterization for High-Performance Computer Architectures

NASA Technical Reports Server (NTRS)

El-Ghazawi, Tarek A.

1995-01-01

This research is conducted in the context of the Joint NSF/NASA Initiative on Evaluation (JNNIE). JNNIE is an inter-agency research program that goes beyond typical.bencbking to provide and in-depth evaluations and understanding of the factors that limit the scalability of high-performance computing systems. Many NSF and NASA centers have participated in the effort. Our research effort was an integral part of implementing JNNIE in the NASA ESS grand challenge applications context. Our research work under this program was composed of three distinct, but related activities. They include the evaluation of NASA ESS high- performance computing testbeds using the wavelet decomposition application; evaluation of NASA ESS testbeds using astrophysical simulation applications; and developing an experimental model for workload characterization for understanding workload requirements. In this report, we provide a summary of findings that covers all three parts, a list of the publications that resulted from this effort, and three appendices with the details of each of the studies using a key publication developed under the respective work.

Knee extensor dynamics in the volleyball approach jump: the influence of patellar tendinopathy.

PubMed

Sorenson, Shawn C; Arya, Shruti; Souza, Richard B; Pollard, Christine D; Salem, George J; Kulig, Kornelia

2010-09-01

Controlled laboratory study using a cross-sectional design. To evaluate knee joint dynamics in elite volleyball players with and without a history of patellar tendinopathy, focusing on mechanical energy absorption and generation. We hypothesized that tendinopathy would be associated withreduced net joint work and net joint power. Patellar tendinopathy is a common, debilitating injury affecting competitive volleyball players. Thirteen elite male players with and without a history of patellar tendinopathy (mean ± SD age, 27 ± 7 years) performed maximum-effort volleyball approach jumps. Sagittal plane knee joint kinematics, kinetics, and energetics were quantified in the lead limb, using data obtained from a force platform and an 8-camera motion analysis system. Vertical ground reaction forces and pelvis vertical velocity at takeoff were examined. Independent sample t tests were used to evaluate group differences (α = .05). The tendinopathy group, compared to controls, demonstrated significant reductions (approximately 30%) in net joint work and net joint power during the eccentric phase of the jump, with no differences in the concentric phase. Positive to-negative net joint work and net joint power ratios were significantly higher in the tendinopathy group, which had a net joint work ratio of 1.00 (95% CI: 0.77, 1.24) versus 0.76 (95% CI: 0.64, 0.88) for controls, and a net joint power ratio of 1.62 (95% CI: 1.15, 2.10) versus 1.00 (95% CI: 0.80, 1.21) for controls. There were no significant differences in net joint moment, angular velocity, or range of motion. Peak vertical ground reaction forces were lower for the tendinopathy group, while average vertical ground reaction forces and pelvis vertical velocity were similar. Patellar tendinopathy is associated with differences in sagittal plane mechanical energy absorption at the knee during maximum-effort volleyball approach jumps. Net joint work and net joint power may help define underlying mechanisms, adaptive effects, or rehabilitative strategies for individuals with patellar tendinopathy.

Genome medicine: gene therapy for the millennium, 30 September-3 October 2001, Rome, Italy.

PubMed

Gruenert, D C; Novelli, G; Dallapiccola, B; Colosimo, A

2002-06-01

The recent surge of DNA sequence information resulting from the efforts of agencies interested in deciphering the human genetic code has facilitated technological developments that have been critical in the identification of genes associated with numerous disease pathologies. In addition, these efforts have opened the door to the opportunity to develop novel genetic therapies to treat a broad range of inherited disorders. Through a joint effort by the University of Vermont, the University of Rome, Tor Vergata, University of Rome, La Sapienza, and the CSS Mendel Institute, Rome, an international meeting, 'Genome Medicine: Gene Therapy for the Millennium' was organized. This meeting provided a forum for the discussion of scientific and clinical advances stimulated by the explosion of sequence information generated by the Human Genome Project and the implications these advances have for gene therapy. The meeting had six sessions that focused on the functional evaluation of specific genes via biochemical analysis and through animal models, the development of novel therapeutic strategies involving gene targeting, artificial chromsomes, DNA delivery systems and non-embryonic stem cells, and on the ethical and social implications of these advances.

Whatever Happened to Joint Vision 2010

DTIC Science & Technology

2010-04-02

submitted to the Faculty of the Joint Advanced Warfighting School in partial satisfaction of the requirements of a Master of Science Degree in Joint...Service efforts and evolve “jointness” beyond the dictates of the 1986 Goldwater-Nichols Act. JV2010 delineated a common set of environmental ...towards something that is fresh, new and important. In this sense, the term vision may have been the wrong term. Warren Bennis and Burt Nanus, noted

Development of a Deployable Nonmetallic Boom for Reconfigurable Systems of Small Spacecraft

NASA Technical Reports Server (NTRS)

Rehnmark, Fredrik; Pryor, Mark; Holmes, Buck; Schaechter, David; Pedreiro, Nelson; Carrington, Connie

2007-01-01

In 2005, NASA commenced Phase 1 of the Modular Reconfigurable High Energy Technology Demonstrator (MRHE) program to investigate reconfigurable systems of small spacecraft. During that year, Lockheed Martin's Advanced Technology Center (ATC) led an accelerated effort to develop a 1-g MRHE concept demonstration featuring robotic spacecraft simulators equipped with docking mechanisms and deployable booms. The deployable boom built for MRHE was the result of a joint effort in which ATK was primarily responsible for developing and fabricating the Collapsible Rollable Tube (CRT patent pending) boom while Lockheed Martin designed and built the motorized Boom Deployment Mechanism (BDM) under a concurrent but separate IR&D program. Tight coordination was necessary to meet testbed integration and functionality requirements. This paper provides an overview of the CRT boom and BDM designs and presents preliminary results of integration and testing to support the MRHE demonstration.

Computational electronics and electromagnetics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shang, C. C.

The Computational Electronics and Electromagnetics thrust area at Lawrence Livermore National Laboratory serves as the focal point for engineering R&D activities for developing computer-based design, analysis, and tools for theory. Key representative applications include design of particle accelerator cells and beamline components; engineering analysis and design of high-power components, photonics, and optoelectronics circuit design; EMI susceptibility analysis; and antenna synthesis. The FY-96 technology-base effort focused code development on (1) accelerator design codes; (2) 3-D massively parallel, object-oriented time-domain EM codes; (3) material models; (4) coupling and application of engineering tools for analysis and design of high-power components; (5) 3-D spectral-domainmore » CEM tools; and (6) enhancement of laser drilling codes. Joint efforts with the Power Conversion Technologies thrust area include development of antenna systems for compact, high-performance radar, in addition to novel, compact Marx generators. 18 refs., 25 figs., 1 tab.« less

Research on the Problem of High-Precision Deployment for Large-Aperture Space-Based Science Instruments

NASA Technical Reports Server (NTRS)

Lake, Mark S.; Peterson, Lee D.; Hachkowski, M. Roman; Hinkle, Jason D.; Hardaway, Lisa R.

1998-01-01

The present paper summarizes results from an ongoing research program conducted jointly by the University of Colorado and NASA Langley Research Center since 1994. This program has resulted in general guidelines for the design of high-precision deployment mechanisms, and tests of prototype deployable structures incorporating these mechanisms have shown microdynamically stable behavior (i.e., dimensional stability to parts per million). These advancements have resulted from the identification of numerous heretofore unknown microdynamic and micromechanical response phenomena, and the development of new test techniques and instrumentation systems to interrogate these phenomena. In addition, recent tests have begun to interrogate nanomechanical response of materials and joints and have been used to develop an understanding of nonlinear nanodynamic behavior in microdynamically stable structures. The ultimate goal of these efforts is to enable nano-precision active control of micro-precision deployable structures (i.e., active control to a resolution of parts per billion).

Toward RADSCAT measurements over the sea and their interpretation

NASA Technical Reports Server (NTRS)

Claassen, J. P.; Fung, A. K.; Wu, S. T.; Chan, H. L.

1973-01-01

Investigations into several areas which are essential to the execution and interpretation of suborbital observations by composite radiometer - scatterometer sensor (RADSCAT) are reported. Experiments and theory were developed to demonstrate the remote anemometric capability of the sensor over the sea through various weather conditions. It is shown that weather situations found in extra tropical cyclones are useful for demonstrating the all weather capability of the composite sensor. The large scale fluctuations of the wind over the sea dictate the observational coverage required to correlate measurements with the mean surface wind speed. Various theoretical investigations were performed to establish a premise for the joint interpretation of the experiment data. The effects of clouds and rains on downward radiometric observations over the sea were computed. A method of predicting atmospheric attenuation from joint observations is developed. In other theoretical efforts, the emission and scattering characteristics of the sea were derived. Composite surface theories with coherent and noncoherent assumptions were employed.

Fusion energy

NASA Astrophysics Data System (ADS)

1990-09-01

The main purpose of the International Thermonuclear Experimental Reactor (ITER) is to develop an experimental fusion reactor through the united efforts of many technologically advanced countries. The ITER terms of reference, issued jointly by the European Community, Japan, the USSR, and the United States, call for an integrated international design activity and constitute the basis of current activities. Joint work on ITER is carried out under the auspices of the International Atomic Energy Agency (IAEA), according to the terms of quadripartite agreement reached between the European Community, Japan, the USSR, and the United States. The site for joint technical work sessions is at the Max Planck Institute of Plasma Physics. Garching, Federal Republic of Germany. The ITER activities have two phases: a definition phase performed in 1988 and the present design phase (1989 to 1990). During the definition phase, a set of ITER technical characteristics and supporting research and development (R and D) activities were developed and reported. The present conceptual design phase of ITER lasts until the end of 1990. The objectives of this phase are to develop the design of ITER, perform a safety and environmental analysis, develop site requirements, define future R and D needs, and estimate cost, manpower, and schedule for construction and operation. A final report will be submitted at the end of 1990. This paper summarizes progress in the ITER program during the 1989 design phase.

Recent Developments in the Design, Capabilities and Autonomous Operations of a Lightweight Surface Manipulation System and Test-bed

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Jones, Thomas C.; Doggett, W. R.; Brady, Jeffrey S.; Berry, Felecia C.; Ganoe, George G.; Anderson, Eric; King, Bruce D.; Mercer, David C.

2011-01-01

The first generation of a versatile high performance device for performing payload handling and assembly operations on planetary surfaces, the Lightweight Surface Manipulation System (LSMS), has been designed and built. Over the course of its development, conventional crane type payload handling configurations and operations have been successfully demonstrated and the range of motion, types of operations and the versatility greatly expanded. This enhanced set of 1st generation LSMS hardware is now serving as a laboratory test-bed allowing the continuing development of end effectors, operational techniques and remotely controlled and automated operations. This paper describes the most recent LSMS and test-bed development activities, that have focused on two major efforts. The first effort was to complete a preliminary design of the 2nd generation LSMS that has the capability for limited mobility and can reposition itself between lander decks, mobility chassis, and fixed base locations. A major portion of this effort involved conducting a study to establish the feasibility of, and define, the specifications for a lightweight cable-drive waist joint. The second effort was to continue expanding the versatility and autonomy of large planetary surface manipulators using the 1st generation LSMS as a test-bed. This has been accomplished by increasing manipulator capabilities and efficiencies through both design changes and tool and end effector development. A software development effort has expanded the operational capabilities of the LSMS test-bed to include; autonomous operations based on stored paths, use of a vision system for target acquisition and tracking, and remote command and control over a communications bridge.

Laser Materials Processing Final Report CRADA No. TC-1526-98

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crane, J.; Lehane, C. J.

2017-09-08

This CRADA project was a joint effort between Lawrence Livermore National Laboratory (LLNL) and United Technologies Corporation (UTC)/Pratt & Whitney (P&W) to demonstrate process capability for drilling holes in turbine airfoils using LLNL-developed femtosecond laser machining technology. The basis for this development was the ability of femtosecond lasers to drill precision holes in variety of materials with little or no collateral damage. The ultimate objective was to develop a laser machine tool consisting of an extremely advanced femtosecond laser subsystem to be developed by LLNL on a best-effort basis and a drilling station for turbine blades and vanes to bemore » developed by P&W. In addition, P&W was responsible for commercializing the system. The goal of the so called Advanced Laser Drilling (ALD) system was to drill specified complex hole-shapes in turbine blades and vanes with a high degree precision and repeatability and simultaneously capable of very high speed processing.« less

SCA Waveform Development for Space Telemetry

NASA Technical Reports Server (NTRS)

Mortensen, Dale J.; Kifle, Multi; Hall, C. Steve; Quinn, Todd M.

2004-01-01

The NASA Glenn Research Center is investigating and developing suitable reconfigurable radio architectures for future NASA missions. This effort is examining software-based open-architectures for space based transceivers, as well as common hardware platform architectures. The Joint Tactical Radio System's (JTRS) Software Communications Architecture (SCA) is a candidate for the software approach, but may need modifications or adaptations for use in space. An in-house SCA compliant waveform development focuses on increasing understanding of software defined radio architectures and more specifically the JTRS SCA. Space requirements put a premium on size, mass, and power. This waveform development effort is key to evaluating tradeoffs with the SCA for space applications. Existing NASA telemetry links, as well as Space Exploration Initiative scenarios, are the basis for defining the waveform requirements. Modeling and simulations are being developed to determine signal processing requirements associated with a waveform and a mission-specific computational burden. Implementation of the waveform on a laboratory software defined radio platform is proceeding in an iterative fashion. Parallel top-down and bottom-up design approaches are employed.

Joint Development of a Fourth Generation Single Crystal Superalloy

NASA Technical Reports Server (NTRS)

Walston, S.; Cetel, A.; MacKay, R.; OHara, K.; Duhl, D.; Dreshfield, R.

2004-01-01

A new, fourth generation, single crystal superalloy has been jointly developed by GE Aircraft Engines, Pratt & Whitney, and NASA. The focus of the effort was to develop a turbine airfoil alloy with long-term durability for use in the High Speed Civil Transport. In order to achieve adequate long-time strength improvements at moderate temperatures and retain good microstructural stability, it was necessary to make significant composition changes from 2nd and 3rd generation single crystal superalloys. These included lower chromium levels, higher cobalt and rhenium levels and the inclusion of a new alloying element, ruthenium. It was found that higher Co levels were beneficial to reducing both TCP precipitation and SRZ formation. Ruthenium caused the refractory elements to partition more strongly to the ' phase, which resulted in better overall alloy stability. The final alloy, EPM 102, had significant creep rupture and fatigue improvements over the baseline production alloys and had acceptable microstructural stability. The alloy is currently being engine tested and evaluated for advanced engine applications.

Engineering tendon and ligament tissues: present developments towards successful clinical products.

PubMed

Rodrigues, Márcia T; Reis, Rui L; Gomes, Manuela E

2013-09-01

Musculoskeletal diseases are one of the leading causes of disability worldwide. Among them, tendon and ligament injuries represent an important aspect to consider in both athletes and active working people. Tendon and ligament damage is an important cause of joint instability, and progresses into early onset of osteoarthritis, pain, disability and eventually the need for joint replacement surgery. The social and economical burden associated with these medical conditions presents a compelling argument for greater understanding and expanding research on this issue. The particular physiology of tendons and ligaments (avascular, hypocellular and overall structural mechanical features) makes it difficult for currently available treatments to reach a complete and long-term functional repair of the damaged tissue, especially when complete tear occurs. Despite the effort, the treatment modalities for tendon and ligament are suboptimal, which have led to the development of alternative therapies, such as the delivery of growth factors, development of engineered scaffolds or the application of stem cells, which have been approached in this review. Copyright © 2012 John Wiley & Sons, Ltd.

Interleaved arrays antenna technology development

NASA Technical Reports Server (NTRS)

1986-01-01

Phase one and two of a program to further develop and investigate advanced graphite epoxy waveguides, radiators, and components with application to space antennas are discussed. The objective of the two phases were to demonstrate mechanical integrity of a small panel of radiators and parts procured under a previous contract and to develop alternate designs and applications of the technology. Most of the emphasis was on the assembly and test of a 5 x 5 element module. This effort was supported by evaluation of adhesives and waveguide joint configurations. The evaluation and final assembly considered not only mechanical performance but also producibility in large scale.

State of Global Pediatric Neurosurgery Outreach: Survey by the International Education Subcommittee

PubMed Central

Davis, Matthew C.; Rocque, Brandon G.; Singhal, Ash; Ridder, Tom; Pattisapu, Jogi V.; Johnston, James M.

2017-01-01

Object Neurosurgical services are increasingly recognized as essential components of surgical care worldwide. Degree of interest among neurosurgeons regarding international work, and barriers to involvement in global neurosurgical outreach, are largely unexplored. We distributed a survey to members of the AANS/CNS Joint Section on Pediatric Neurosurgery to assess the state of global outreach among its members and identify barriers to involvement. Methods An internet-based questionnaire was developed by the International Education Subcommittee of the AANS/CNS Joint Section on Pediatric Neurosurgery, and distributed to pediatric neurosurgeons via the AANS/CNS Joint Section email contact list. Participants were surveyed on involvement in global neurosurgical outreach, geographic location, nature of participation, and barriers to further involvement. Results A 35.3% response rate was obtained, with 116 respondents completed the survey. 61% performed or taught neurosurgery in a developing country, 49% traveling at least annually. Africa was the most common region (54%), followed by South America (30%), through 29 separate organizing entities. Hydrocephalus was the most commonly treated condition (88%), followed by spinal dysraphism (74%) and tumor (68%). Most respondents obtained follow-up through communication from local surgeons (77%). 71% believed the international experience improved their practice, and 74% were very or extremely interested in working elsewhere. Interference with current practice (61%), cost (44%), and difficulty identifying international partners (43%) were the most commonly cited barriers to participation. Conclusion Any coordinated effort to expand global neurosurgical capacity begins with appreciation for the current state of outreach efforts. Increasing participation in global outreach will require addressing both real and perceived barriers to involvement. Creation and curation of a centralized online database of ongoing projects to facilitate coordination and involvement may be beneficial. PMID:28524788

The Disestablishment of U.S. Joint Forces Command: A Step Backward in Jointness

DTIC Science & Technology

2011-06-01

and the less than stellar 1983 rescue of a few medical students from the island of Grenada (Operation Urgent Fury), Congress passed the Goldwater...an opportunity for dialogue and a source of basic joint doctrine, it was widely ignored despite increasing tension and preparation for the Second... basic unity of effort appeared lacking even with dialogue like the Key West Agreements. Dr. William Niskanen, with the CATO Institute, described the

VIIRS validation and algorithm development efforts in coastal and inland Waters

NASA Astrophysics Data System (ADS)

Stengel, E.; Ondrusek, M.

2016-02-01

Accurate satellite ocean color measurements in coastal and inland waters are more challenging than open-ocean measurements. Complex water and atmospheric conditions can limit the utilization of remote sensing data in coastal waters where it is most needed. The Coastal Optical Characterization Experiment (COCE) is an ongoing project at NOAA/NESDIS/STAR Satellite Oceanography and Climatology Division. The primary goals of COCE are satellite ocean color validation and application development. Currently, this effort concentrates on the initialization and validation of the Joint Polar Satellite System (JPSS) VIIRS sensor using a Satlantic HyperPro II radiometer as a validation tool. A report on VIIRS performance in coastal waters will be given by presenting comparisons between in situ ground truth measurements and VIIRS retrievals made in the Chesapeake Bay, and inland waters of the Gulf of Mexico and Puerto Rico. The COCE application development effort focuses on developing new ocean color satellite remote sensing tools for monitoring relevant coastal ocean parameters. A new VIIRS total suspended matter algorithm will be presented for the Chesapeake Bay. These activities improve the utility of ocean color satellite data in monitoring and analyzing coastal and oceanic processes. Progress on these activities will be reported.

Durability of building joint sealants

Treesearch

Christopher C. White; Kar Tean Tan; Donald L. Hunston; R. Sam Williams

2009-01-01

Predicting the service life of building joint sealants exposed to service environments in less than real time has been a need of the sealant community for many decades. Despite extensive research efforts to design laboratory accelerated tests to duplicate the failure modes occurring in field exposures, little success has been achieved using conventional durability...

Corrosion-protective coatings from electrically conducting polymers

NASA Technical Reports Server (NTRS)

Thompson, Karen Gebert; Bryan, Coleman J.; Benicewicz, Brian C.; Wrobleski, Debra A.

1991-01-01

In a joint effort between NASA Kennedy and LANL, electrically conductive polymer coatings were developed as corrosion protective coatings for metal surfaces. At NASA Kennedy, the launch environment consist of marine, severe solar, and intermittent high acid and/or elevated temperature conditions. Electrically conductive polymer coatings were developed which impart corrosion resistance to mild steel when exposed to saline and acidic environments. Such coatings also seem to promote corrosion resistance in areas of mild steel where scratches exist in the protective coating. Such coatings appear promising for many commercial applications.

A Potential NASA Research Reactor to Support NTR Development

NASA Technical Reports Server (NTRS)

Eades, Michael; Gerrish, Harold; Hardin, Leroy

2013-01-01

In support of efforts for research into the design and development of a man rated Nuclear Thermal Rocket (NTR) engine, the National Aeronautics and Space Administration (NASA), Marshall Space Flight Center (MSFC), is evaluating the potential for building a Nuclear Regulatory Commission (NRC) licensed research reactor. The proposed reactor would be licensed by NASA and operated jointly by NASA and university partners. The purpose of this reactor would be to perform further research into the technologies and systems needed for a successful NTR project and promote nuclear training and education.

A Research Reactor Concept to Support NTP Development

NASA Technical Reports Server (NTRS)

Eades, Michael J.; Blue, T. E.; Gerrish, Harold P.; Hardin, Leroy A.

2014-01-01

In support of efforts for research into the design and development of man rated Nuclear Thermal Propulsion (NTP), the National Aeronautics and Space Administration (NASA), Marshall Space Flight Center (MSFC), is evaluating the potential for building a Nuclear Regulatory Commission (NRC) licensed NTP based research reactor (NTPRR). The proposed NTPRR would be licensed by NASA and operated jointly by NASA and university partners. The purpose of the NTPRR would be used to perform further research into the technologies and systems needed for a successful NTP project and promote nuclear training and education.

COBRA System Engineering Processes to Achieve SLI Strategic Goals

NASA Technical Reports Server (NTRS)

Ballard, Richard O.

2003-01-01

The COBRA Prototype Main Engine Development Project was an endeavor conducted as a joint venture between Pratt & Whitney and Aerojet to conduct risk reduction in LOX/LH2 main engine technology for the NASA Space Launch Initiative (SLI). During the seventeen months of the project (April 2001 to September 2002), approximately seventy reviews were conducted, beginning with the Engine Systems Requirements Review (SRR) and ending with the Engine Systems Interim Design Review (IDR). This paper discusses some of the system engineering practices used to support the reviews and the overall engine development effort.

The Joint Space Operations Center Mission System and the Advanced Research, Collaboration, and Application Development Environment Status Update 2016

NASA Astrophysics Data System (ADS)

Murray-Krezan, Jeremy; Howard, Samantha; Sabol, Chris; Kim, Richard; Echeverry, Juan

2016-05-01

The Joint Space Operations Center (JSpOC) Mission System (JMS) is a service-oriented architecture (SOA) infrastructure with increased process automation and improved tools to enhance Space Situational Awareness (SSA) performed at the US-led JSpOC. The Advanced Research, Collaboration, and Application Development Environment (ARCADE) is a test-bed maintained and operated by the Air Force to (1) serve as a centralized test-bed for all research and development activities related to JMS applications, including algorithm development, data source exposure, service orchestration, and software services, and provide developers reciprocal access to relevant tools and data to accelerate technology development, (2) allow the JMS program to communicate user capability priorities and requirements to developers, (3) provide the JMS program with access to state-of-the-art research, development, and computing capabilities, and (4) support JMS Program Office-led market research efforts by identifying outstanding performers that are available to shepherd into the formal transition process. In this paper we will share with the international remote sensing community some of the recent JMS and ARCADE developments that may contribute to greater SSA at the JSpOC in the future, and share technical areas still in great need.

Dislocation of temporo-mandibular joint - an uncommon circumstance of occurrence: vaginal delivery.

PubMed

El Bouazzaoui, Abderrahim; Labib, Smael; Derkaoui, Ali; Adnane Berdai, Mohammed; Bendadi, Azzeddine; Harandou, Mustapha

2010-06-25

Dislocation of temporo-mandibular joint (TMJ) is an infrequent disease but still spectacular. This disease consists of a permanent, to some extent complete disruption of the temporo-mandibular joint. These dislocations often occur in a context of yawning, and less frequently after a burst of laughing or relatively mild facial trauma (slap, punch on the chin). We report a case of TMJ occurring in an uncommon circumstance: vaginal delivery. A woman aged 24-years with no special past medical history; primipara was admitted in the Department of Maternity of the University Hospital Hassan II of Fez for an imminent delivery of a twin pregnancy. Ten minutes after admission, the patient delivered vaginally with episiotomy. She gave birth to twins weighing 2800 g and 2400 g. During labour, and due to efforts of crying, the patient developed a sudden and immediate loss of function of the temporo-mandibular joint, with difficulty of speaking, the mouth permanently opened and with the chin lowered and thrown forward. The examination found an empty glenoid fossa of the temporo-mandibular joint in both sides. The diagnosis of dislocation of the TMJ was established. A CT scan of facial bones was done, objectifying a bilateral dislocation of TMJ. The reduction of this dislocation was performed in the operating room under sedation.

Computerized Adaptive Testing (CAT): A User Manual

DTIC Science & Technology

1984-03-12

NPRDC TR 84-32 COMPUTERIZED ADAPTIVE TESTING ( CAT ): A USER MANUAL Susan Hardwick Lawrence Eastman Ross Cooper Rehab Group, Incorporated San...a ~EI’IOD COVIRED COMPUTERIZED ADAPTIVE TESTING ( CAT ) Final Report Aug 1981-June 1982 A USER MANUAL 1. ~l:l’t,ORMINCI ORCI. RE~ORT NUM.I:R 62-83...II nee• .. _, entl ldentll)’ ,,. llloclr _,.,) A joint-service effort is underway to develop a computerized adaptive testing ( CAT ) system and to

Uneven-aged silviculture and management in the eastern United States: Proceedings of an In-Service Workshop; Morgantown, West Virginia; July 15-17, 1975

Treesearch

Warren T. Doolittle; A. P. Mustain; Carter B. Gibbs; David. A. Marquis; Barton M. Blum; Carl H. Tubbs; W. B. Leak; S. F. Gingrich; H. Clay Smith; Paul S. DeBald; LaMont G. Engle; Robert E. Phares

1975-01-01

The workshop, summarized in this Proceedings, represented a joint effort by personnel from Research, National Forest System, and State and Private Forestry, to review the state-of-the-art knowledge about the applicability of uneven-aged silviculture and management in the eastern United States. One major objective of this review was to develop a much better mutual...

A Compendium of Brazed Microstructures For Fission Power Systems Applications

NASA Technical Reports Server (NTRS)

Locci, Ivan E.; Bowman, Cheryl L.

2012-01-01

NASA has been supporting design studies and technology development for fission-based power systems that could provide power to an outpost on the Moon, Mars, or an asteroid. Technology development efforts have included fabrication and evaluation of components used in a Stirling engine power conversion system. This investigation is part of the development of several braze joints crucial for the heat exchanger transfer path from a hot-side heat exchanger to a Stirling engine heat acceptor. Dissimilar metal joints are required to impart both mechanical strength and thermal path integrity for a heater head of interest. Preliminary design work for the heat exchanger involved joints between low carbon stainless steel to Inconel 718, where the 316L stainless steel would contain flowing liquid metal NaK while Inconel 718, a stronger alloy, would be used as structural reinforcement. This paper addressed the long-term microstructural stability of various braze alloys used to join 316L stainless steel heater head to the high conductivity oxygen-free copper acceptor to ensure the endurance of the critical metallic components of this sophisticated heat exchanger. The bonding of the 316L stainless steel heater head material to a copper heat acceptor is required to increase the heat-transfer surface area in contact with flowing He, which is the Stirling engine working fluid.

Advanced computational tools for 3-D seismic analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barhen, J.; Glover, C.W.; Protopopescu, V.A.

1996-06-01

The global objective of this effort is to develop advanced computational tools for 3-D seismic analysis, and test the products using a model dataset developed under the joint aegis of the United States` Society of Exploration Geophysicists (SEG) and the European Association of Exploration Geophysicists (EAEG). The goal is to enhance the value to the oil industry of the SEG/EAEG modeling project, carried out with US Department of Energy (DOE) funding in FY` 93-95. The primary objective of the ORNL Center for Engineering Systems Advanced Research (CESAR) is to spearhead the computational innovations techniques that would enable a revolutionary advancemore » in 3-D seismic analysis. The CESAR effort is carried out in collaboration with world-class domain experts from leading universities, and in close coordination with other national laboratories and oil industry partners.« less

Repair and tissue engineering techniques for articular cartilage

PubMed Central

Makris, Eleftherios A.; Gomoll, Andreas H.; Malizos, Konstantinos N.; Hu, Jerry C.; Athanasiou, Kyriacos A.

2015-01-01

Chondral and osteochondral lesions due to injury or other pathology commonly result in the development of osteoarthritis, eventually leading to progressive total joint destruction. Although current progress suggests that biologic agents can delay the advancement of deterioration, such drugs are incapable of promoting tissue restoration. The limited ability of articular cartilage to regenerate renders joint arthroplasty an unavoidable surgical intervention. This Review describes current, widely used clinical repair techniques for resurfacing articular cartilage defects; short-term and long-term clinical outcomes of these techniques are discussed. Also reviewed is a developmental pipeline of regenerative biological products that over the next decade could revolutionize joint care by functionally healing articular cartilage. These products include cell-based and cell-free materials such as autologous and allogeneic cell-based approaches and multipotent and pluripotent stem-cell-based techniques. Central to these efforts is the prominent role that tissue engineering has in translating biological technology into clinical products; therefore, concomitant regulatory processes are also discussed. PMID:25247412

Joint Power Charging and Routing in Wireless Rechargeable Sensor Networks.

PubMed

Jia, Jie; Chen, Jian; Deng, Yansha; Wang, Xingwei; Aghvami, Abdol-Hamid

2017-10-09

The development of wireless power transfer (WPT) technology has inspired the transition from traditional battery-based wireless sensor networks (WSNs) towards wireless rechargeable sensor networks (WRSNs). While extensive efforts have been made to improve charging efficiency, little has been done for routing optimization. In this work, we present a joint optimization model to maximize both charging efficiency and routing structure. By analyzing the structure of the optimization model, we first decompose the problem and propose a heuristic algorithm to find the optimal charging efficiency for the predefined routing tree. Furthermore, by coding the many-to-one communication topology as an individual, we further propose to apply a genetic algorithm (GA) for the joint optimization of both routing and charging. The genetic operations, including tree-based recombination and mutation, are proposed to obtain a fast convergence. Our simulation results show that the heuristic algorithm reduces the number of resident locations and the total moving distance. We also show that our proposed algorithm achieves a higher charging efficiency compared with existing algorithms.

Joint Power Charging and Routing in Wireless Rechargeable Sensor Networks

PubMed Central

Jia, Jie; Chen, Jian; Deng, Yansha; Wang, Xingwei; Aghvami, Abdol-Hamid

2017-01-01

The development of wireless power transfer (WPT) technology has inspired the transition from traditional battery-based wireless sensor networks (WSNs) towards wireless rechargeable sensor networks (WRSNs). While extensive efforts have been made to improve charging efficiency, little has been done for routing optimization. In this work, we present a joint optimization model to maximize both charging efficiency and routing structure. By analyzing the structure of the optimization model, we first decompose the problem and propose a heuristic algorithm to find the optimal charging efficiency for the predefined routing tree. Furthermore, by coding the many-to-one communication topology as an individual, we further propose to apply a genetic algorithm (GA) for the joint optimization of both routing and charging. The genetic operations, including tree-based recombination and mutation, are proposed to obtain a fast convergence. Our simulation results show that the heuristic algorithm reduces the number of resident locations and the total moving distance. We also show that our proposed algorithm achieves a higher charging efficiency compared with existing algorithms. PMID:28991200

Joint Spacelab-J (SL-J) Activities at the Huntsville Operations Support Center (HOSC) Spacelab

NASA Technical Reports Server (NTRS)

1999-01-01

The science laboratory, Spacelab-J (SL-J), flown aboard the STS-47 flight was a joint venture between NASA and the National Space Development Agency of Japan (NASDA) utilizing a manned Spacelab module. The mission conducted 24 materials science and 20 life science experiments, of which 35 were sponsored by NASDA, 7 by NASA, and two collaborative efforts. Materials science investigations covered such fields as biotechnology, electronic materials, fluid dynamics and transport phenomena, glasses and ceramics, metals and alloys, and acceleration measurements. Life sciences included experiments on human health, cell separation and biology, developmental biology, animal and human physiology and behavior, space radiation, and biological rhythms. Test subjects included the crew, Japanese koi fish (carp), cultured animal and plant cells, chicken embryos, fruit flies, fungi and plant seeds, and frogs and frog eggs. Featured together in joint ground activities during the SL-J mission are NASA/NASDA personnel at the Huntsville Operations Support Center (HOSC) Spacelab Payload Operations Control Center (SL POCC) at Marshall Space Flight Center (MSFC).

Results of the Simulation and Assimilation of Doppler Wind Lidar Observations in Preparation for European Space Agency's Aeolus Mission

NASA Technical Reports Server (NTRS)

McCarty, Will

2011-01-01

With the launch of the European Space Agency's Aeolus Mission in 2013, direct spaceborne measurements of vertical wind profiles are imminent via Doppler wind lidar technology. Part of the preparedness for such missions is the development of the proper data assimilation methodology for handling such observations. Since no heritage measurements exist in space, the Joint Observing System Simulation Experiment (Joint OSSE) framework has been utilized to generate a realistic proxy dataset as a precursor to flight. These data are being used for the development of the Gridpoint Statistical Interpolation (GSI) data assimilation system utilized at a number of centers through the United States including the Global Modeling and Assimilation Office (GMAO) at NASA/Goddard Space Flight Center and at the National Centers for Environmental Prediction (NOAA/NWS/NCEP) as an activity through the Joint Center for Satellite Data Assimilation. An update of this ongoing effort will be presented, including the methodology of proxy data generation, the limitations of the proxy data, the handling of line-of-sight wind measurements within the GSI, and the impact on both analyses and forecasts with the addition of the new data type.

Conversion of Indigenous Agricultural Waste Feedstocks to Fuel Ethanol. Cooperative Research and Development Final Report, CRADA Number CRD-13-504

DOE Office of Scientific and Technical Information (OSTI.GOV)

Elander, Richard

This Cooperative Research and Development Agreement (CRADA) is between the National Renewable Energy Laboratory (NREL), a world leader in biomass conversion research and Ecopetrol American Inc., Ecopetrol S.A.'s U.S. subsidiary. The research and development efforts described in the Joint Work Statement (JWS) will take advantage of the strengths of both parties. NREL will use its Integrated Biorefinery Facility and vast experience in the conversion of lignocellulosic feedstocks to fuel ethanol to develop processes for the conversion of Ecopetrol's feedstocks. Ecopetrol will establish the infrastructure in Columbia to commercialize the conversion process.

Multidisciplinary Design Technology Development: A Comparative Investigation of Integrated Aerospace Vehicle Design Tools

NASA Technical Reports Server (NTRS)

Renaud, John E.; Batill, Stephen M.; Brockman, Jay B.

1999-01-01

This research effort is a joint program between the Departments of Aerospace and Mechanical Engineering and the Computer Science and Engineering Department at the University of Notre Dame. The purpose of the project was to develop a framework and systematic methodology to facilitate the application of Multidisciplinary Design Optimization (MDO) to a diverse class of system design problems. For all practical aerospace systems, the design of a systems is a complex sequence of events which integrates the activities of a variety of discipline "experts" and their associated "tools". The development, archiving and exchange of information between these individual experts is central to the design task and it is this information which provides the basis for these experts to make coordinated design decisions (i.e., compromises and trade-offs) - resulting in the final product design. Grant efforts focused on developing and evaluating frameworks for effective design coordination within a MDO environment. Central to these research efforts was the concept that the individual discipline "expert", using the most appropriate "tools" available and the most complete description of the system should be empowered to have the greatest impact on the design decisions and final design. This means that the overall process must be highly interactive and efficiently conducted if the resulting design is to be developed in a manner consistent with cost and time requirements. The methods developed as part of this research effort include; extensions to a sensitivity based Concurrent Subspace Optimization (CSSO) NMO algorithm; the development of a neural network response surface based CSSO-MDO algorithm; and the integration of distributed computing and process scheduling into the MDO environment. This report overviews research efforts in each of these focus. A complete bibliography of research produced with support of this grant is attached.

Development of Guidelines for In-Situ Repair of SLS-Class Composite Flight Hardware

NASA Technical Reports Server (NTRS)

Weber, Thomas P., Jr.; Cox, Sarah B.

2018-01-01

The purpose of composite repair development at KSC (John F. Kennedy Space Center) is to provide support to the CTE (Composite Technology for Exploration) project. This is a multi-space center effort with the goal of developing bonded joint technology for SLS (Space Launch System) -scale composite hardware. At KSC, effective and efficient repair processes need to be developed to allow for any potential damage to composite components during transport or launch preparation. The focus of the composite repair development internship during the spring of 2018 was on the documentation of repair processes and requirements for process controls based on techniques developed through hands-on work with composite test panels. Three composite test panels were fabricated for the purpose of repair and surface preparation testing. The first panel included a bonded doubler and was fabricated to be damaged and repaired. The second and third panels were both fabricated to be cut into lap-shear samples to test the strength of bond of different surface preparation techniques. Additionally, jointed composite test panels were impacted at MSFC (Marshall Space Flight Center) and analyzed for damage patterns. The observations after the impact tests guided the repair procedure at KSC to focus on three repair methods. With a finalized repair plan in place, future work will include the strength testing of different surface preparation techniques, demonstration of repair methods, and repair of jointed composite test panels being impacted at MSFC.

The Joint NASA/Goddard-University of Maryland Research Program in Charged Particle and High Energy Photon Detector Technology

NASA Technical Reports Server (NTRS)

1988-01-01

Having recognized at an early stage the critical importance of maintaining detector capabilities which utilize state of the art techniques, a joint program was formulated. This program has involved coordination of a broad range of efforts and activities including joint experiments, collaboration in theoretical studies, instrument design, calibrations, and data analysis. Summaries of the progress made to date are presented. A representative bibliography is also included.

Joint Decision No. KEP-235/MEN 1985 and No. 114/MENKES/SKB/111/1985 and Joint Decision No. KEP-333/MEN/1985 and No. 15/MENKES/SKB/IV/1985, 1985.

PubMed

1988-01-01

Under these Joint Decisions, all industrial establishments employing 300 or more workers are obliged to establish an in-plant health clinic and to provide contraceptive services to eligible worker couples. Under Joint Decree No. KEP.12/MEN/1984 of the Ministry of Manpower, the Indonesian Labor Federation and the Indonesian Employers Association agreed to step up their family planning efforts in the industrial sector with the cooperation of the National Family Planning Coordinating Board. full text

Probabilistic accident consequence uncertainty analysis -- Late health effects uncertain assessment. Volume 2: Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Little, M.P.; Muirhead, C.R.; Goossens, L.H.J.

1997-12-01

The development of two new probabilistic accident consequence codes, MACCS and COSYMA, was completed in 1990. These codes estimate the consequence from the accidental releases of radiological material from hypothesized accidents at nuclear installations. In 1991, the US Nuclear Regulatory Commission and the Commission of the European Communities began cosponsoring a joint uncertainty analysis of the two codes. The ultimate objective of this joint effort was to systematically develop credible and traceable uncertainty distributions for the respective code input variables. A formal expert judgment elicitation and evaluation process was identified as the best technology available for developing a library ofmore » uncertainty distributions for these consequence parameters. This report focuses on the results of the study to develop distribution for variables related to the MACCS and COSYMA late health effects models. This volume contains appendices that include (1) a summary of the MACCS and COSYMA consequence codes, (2) the elicitation questionnaires and case structures, (3) the rationales and results for the expert panel on late health effects, (4) short biographies of the experts, and (5) the aggregated results of their responses.« less

Probabilistic accident consequence uncertainty analysis -- Uncertainty assessment for internal dosimetry. Volume 2: Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goossens, L.H.J.; Kraan, B.C.P.; Cooke, R.M.

1998-04-01

The development of two new probabilistic accident consequence codes, MACCS and COSYMA, was completed in 1990. These codes estimate the consequence from the accidental releases of radiological material from hypothesized accidents at nuclear installations. In 1991, the US Nuclear Regulatory Commission and the Commission of the European Communities began cosponsoring a joint uncertainty analysis of the two codes. The ultimate objective of this joint effort was to systematically develop credible and traceable uncertainty distributions for the respective code input variables. A formal expert judgment elicitation and evaluation process was identified as the best technology available for developing a library ofmore » uncertainty distributions for these consequence parameters. This report focuses on the results of the study to develop distribution for variables related to the MACCS and COSYMA internal dosimetry models. This volume contains appendices that include (1) a summary of the MACCS and COSYMA consequence codes, (2) the elicitation questionnaires and case structures, (3) the rationales and results for the panel on internal dosimetry, (4) short biographies of the experts, and (5) the aggregated results of their responses.« less

Building a Quality Workforce. A Joint Initiative.

ERIC Educational Resources Information Center

Department of Commerce, Washington, DC.

For this joint effort among three Cabinet Agencies, studies by a variety of organizations were reviewed and 134 business leaders and 34 education leaders in many communities throughout the United States were interviewed to determine what businesses find lacking among new entrants into the labor force and what employers' work force needs will be in…

Sharing Technology for a Joint-Use Library

ERIC Educational Resources Information Center

Woods, Richard F.

2004-01-01

Building joint-use libraries to foster new types of learning and collaboration is a growing phenomenon that is of great interest to academic library planners around the world. Noteworthy among these efforts, the Dr. Martin Luther King, Jr. Library in San Jose, California, is a collaboration of a metropolitan university library and a major public…

Influence of manual therapy on functional mobility after joint injury in a rat model.

PubMed

Ruhlen, Rachel L; Snider, Eric J; Sargentini, Neil J; Worthington, Bart D; Singh, Vineet K; Pazdernik, Vanessa K; Johnson, Jane C; Degenhardt, Brian F

2013-10-01

Animal models can be used to investigate manual therapy mechanisms, but testing manipulation in animal models is problematic because animals cannot directly report their pain. To develop a rat model of inflammatory joint injury to test the efficacy of manual therapy in reducing nociception and restoring function. The authors induced acute inflammatory joint injury in rats by injecting carrageenan into the ankle and then measured voluntary running wheel activity in treated and untreated rats. Treatments included manual therapy applied to the ankle and knee of the injured limb and several analgesic medications (eg, morphine, ketorolac, prednisone). Intra-articular injection of carrageenan to the ankle produced significant swelling (diameter of the ankle increased by 64% after injection; P=.004) and a robust reduction in voluntary running wheel activity (running distance reduced by 91% compared with controls; P<.001). Injured rats gradually returned to running levels equal to controls over 10 days. Neither manual therapy nor analgesic medications increased running wheel activity relative to untreated rats. Voluntary running wheel activity appears to be an appropriate functional measure to evaluate the impact of an acute inflammatory joint injury. However, efforts to treat the injury did not restore running relative to untreated rats.

Development of Mathematic Model of Cold Welding at Drawing-up the Flange Joint of Pneumohydraulic Systems

NASA Astrophysics Data System (ADS)

Boyko, Y. S.

2002-01-01

Provision of high airtightness of joints of pipe- lines of pneumohydraulic systems (PHS) operating under high pressure, is an important task for designing and operation of launch vehicles. In the process of assembly and tests of PHS of launch vehicles, it was found that detachable flange joints do not lose their airtightness after removal of fastening elements, even in conditions of standard loads. The task of this work is in studying a phenomenon connected with initiation of the observed effect of adhesion and also stresses in the zone of contact at drawing- up the flange detachable joints with a plastic gasket. Investigations have shown that density of the joint is kept due to cold welding, as the created conditions are helpful for that process. As a result of the investigations performed, we have developed a mathematic model which is based on application of the theory of metal bonds; that theory explains the essence of the effect observed. Basic factors which provide optimum mode of cold welding, are effort which can cause microplastic deformation and form maximum contact, and also quality of processing the material of the surfaces joined. Strength of all- metal joint depends on factual area of contact. So, surface processing quality defines a configuration of microbulges which come into contact not simultaneously, and their stressed state is different, and it influences the character of dependence of the contact area on loading. Results of calculations by the mathematic model are expressed by dependencies of factual area of contact and a single diameter of the contact spot on the load applied which compresses the materials with various physical properties, and on the surface processing quality. The mathematic model allows to explain the common character of the cold welding process in detachable flange joints with the plastic gasket, to determine the nature and the character of acting forces, to define kinetics and the mechanism of formation of cold welding of detachable joints. It also helps to analyze the state of airtightness and to metal welding technology in the plastic state at drawing- up of detachable flange joints with a plastic gasket and to review cold welding as a positive phenomenon.

Static and Fatigue Strength Evaluations for Bolted Composite/Steel Joints for Heavy Vehicle Chassis Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xin; Stephens, Elizabeth V.; Herling, Darrell R.

2004-09-14

In May 2003, ORNL and PNNL began collaboration on a four year research effort focused on developing joining techniques to overcome the technical issues associated with joining lightweight materials in heavy vehicles. The initial focus of research is the development and validation of joint designs for a composite structural member attached to a metal member that satisfy the structural requirements both economically and reliably. Huck-bolting is a common joining method currently used in heavy truck chassis structures. The initial round of testing was conducted to establish a performance benchmark by evaluating the static and fatigue behavior of an existing steel/steelmore » chassis joint at the single huck-bolt level. Both tension and shear loading conditions were considered, and the resulting static and fatigue strengths will be used to guide the joint design for a replacement composite/steel joint. A commercially available, pultruded composite material was chosen to study the generic issues related to composite/steel joints. Extren is produced by STRONGWELL, and it is a combination of fiberglass reinforcement and thermosetting polyester or vinyl ester resin systems. Extren sheets of 3.2 mm thick were joined to 1.4 mm SAE1008 steel sheets with a standard grade 5 bolt with 6.35 mm diameter. Both tension and shear loading modes were considered for the single hybrid joint under static and fatigue loading conditions. Since fiberglass reinforced thermoset polymer composites are a non-homogenous material, their strengths and behavior are dependent upon the design of the composite and reinforcement. The Extren sheet stock was cut along the longitudinal direction to achieve maximum net-section strength. The effects of various manufacturing factors and operational conditions on the static and fatigue strength of the hybrid joint were modeled and experimentally verified. It was found that loading mode and washer size have significant influence on the static and fatigue strength of the hybrid joint. The effect of different fatigue test frequencies on the sample temperature and the resulting fatigue life was also examined.« less

Executive Summary of the American Heart Association and American Thoracic Society Joint Guidelines for Pediatric Pulmonary Hypertension

PubMed Central

Ivy, D. Dunbar; Archer, Stephen L.; Wilson, Kevin

2016-01-01

Although pulmonary hypertension (PH) contributes significantly to poor outcomes in diverse pediatric diseases, approaches toward the care of children with PH have been limited by the lack of consensus guidelines from experts in the field. In a joint effort from the American Heart Association and American Thoracic Society, a committee of experienced clinicians was formed to systematically identify, synthesize, and appraise relevant evidence and then to formulate evidence-based recommendations regarding the diagnosis and management of pediatric PH. This brief report is an executive summary of the officially approved guidelines developed by the committee, highlighting a few key recommendations regarding the care of children with PH. Guidelines and the rationale for grading the strength of each recommendation are included in the online supplement. PMID:27689707

NASA-DoD Lower Process Temperature Lead-Free Solder Project Overview

NASA Technical Reports Server (NTRS)

Kessel, Kurt R.

2014-01-01

This project is a follow-on effort to the Joint Council on Aging AircraftJoint Group on Pollution Prevention (JCAAJG-PP) Pb-free Solder Project and NASA-DoD Lead-Free Electronics Project which were the first projects to test the reliability of Pb-free solder joints against the requirements of the aerospace and military community. This effort would continue to build on the results from the JCAAJG-PP Lead-Free Solder Project and NASA-DoD Lead-Free Electronics Project while focusing on a particular failure mechanism currently plaguing Pb-free assemblies, pad cratering.The NASA-DoD Lead-Free Electronics Project confirmed that pad cratering is one of the dominant failure modes that occur in various board level reliability tests, especially under dynamic loading. Pad Cratering is a latent defect that may occur during assembly, rework, and post assembly handling and testing.

The academic-industrial complex: navigating the translational and cultural divide.

PubMed

Freedman, Stephen; Mullane, Kevin

2017-07-01

In general, the fruits of academic discoveries can only be realized through joint efforts with industry. However, the poor reproducibility of much academic research has damaged credibility and jeopardized translational efforts that could benefit patients. Meanwhile, journals are rife with articles bemoaning the limited productivity and increasing costs of the biopharmaceutical industry and its resultant predilection for mergers and reorganizations while decreasing internal research efforts. The ensuing disarray and uncertainty has created tremendous opportunities for academia and industry to form even closer ties, and to embrace new operational and financial models to their joint benefit. This review article offers a personal perspective on the opportunities, models and approaches that harness the increased interface and growing interdependency between biomedical research institutes, the biopharmaceutical industry and the technological world. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biomechanical energy harvesting: generating electricity during walking with minimal user effort.

PubMed

Donelan, J M; Li, Q; Naing, V; Hoffer, J A; Weber, D J; Kuo, A D

2008-02-08

We have developed a biomechanical energy harvester that generates electricity during human walking with little extra effort. Unlike conventional human-powered generators that use positive muscle work, our technology assists muscles in performing negative work, analogous to regenerative braking in hybrid cars, where energy normally dissipated during braking drives a generator instead. The energy harvester mounts at the knee and selectively engages power generation at the end of the swing phase, thus assisting deceleration of the joint. Test subjects walking with one device on each leg produced an average of 5 watts of electricity, which is about 10 times that of shoe-mounted devices. The cost of harvesting-the additional metabolic power required to produce 1 watt of electricity-is less than one-eighth of that for conventional human power generation. Producing substantial electricity with little extra effort makes this method well-suited for charging powered prosthetic limbs and other portable medical devices.

Encounter with disaster: a medical diary of Hiroshima, 1945. Condensed from the original publication, 1965.

PubMed Central

Liebow, A. A.

1983-01-01

The effects of the atomic bomb dropped on Hiroshima and Nagasaki in 1945 are described. Immediately after the bombing, Japanese civilian and military authorities mobilized an intense effort to provide help to the damaged cities and their inhabitants. At the same time, research was undertaken by the Japanese in an attempt to determine the nature of the effects of the bombs on the population. Some weeks later, the American armed services and the Manhattan District also organized an investigation of these effects. This memoir describes the early days of the American research effort, its integration with the Japanese program, and the development of a Joint Commission to study the effects of the bombing. After the first rapid survey, described in this paper, the effort was reorganized and continued under the sponsorship of the National Research Councils of America and Japan as the Atomic Bomb Casualty Commission. PMID:6349144

Ultrasonic Nondestructive Evaluation of PRSEUS Pressure Cube Article in Support of Load Test to Failure

NASA Technical Reports Server (NTRS)

Johnston, Patrick H.

2013-01-01

The PRSEUS Pressure Cube Test was a joint development effort between the Boeing Company and NASA Langley Research Center, sponsored in part by the Environmentally Responsible Aviation Project and Boeing internal R&D. This Technical Memorandum presents the results of ultrasonic inspections in support of the PRSEUS Pressure Cube Test, and is a companion document with the NASA test report and a report on the acoustic emission measurements made during the test.

The Agent-Based Simulation (ABS) Verification, validation and Accreditation (VV&A) Study Phase 2 - Joint/DoD

DTIC Science & Technology

2008-09-15

however, a variety of so-called variance-reduction techniques ( VRTs ) that have been developed, which reduce output variance with little or no...additional computational effort. VRTs typically achieve this via judicious and careful reuse of the basic underlying random nmnbers. Perhaps the best-known...typical simulation situation- change a weapons-system configuration and see what difference it makes). Key to making CRN and most other VRTs work

EXTENSION EDUCATION SYMPOSIUM: Getting the most out of your extension appointment and still having a life.

PubMed

Powers, W; Cockett, N; Lardy, G

2017-04-01

Managing the demands of an academic appointment in extension can be a challenging task. Demands from constituent groups, expectations of supervisors, and rigors of promotion and tenure processes can create pressures that young faculty did not expect. Throw in spousal and family duties and you have created a situation that many will find hard to navigate. However, there are ways to cope and, even better news, there are ways to excel in meeting the demands of an academic appointment and enjoying life. Because many new extension faculty members do not have prior experience in extension, best practices in documenting programs and extension scholarship over the pretenure period are provided in this paper. Appointments that include both research and extension are quite common at many land grant universities. The advantages of joint appointments are numerous and include the fact that more and more grant agencies are seeking integrated research, teaching, and/or extension projects. However, the time demands of joint appointments can be challenging. Joint appointments can be designed to help faculty members conduct important translational research and have it be applied in a production setting. By seeking commonalities in research and extension efforts, joint appointments can be very synergistic. Development of highly successful programs requires planning on the front end with an emphasis on an in-depth needs assessment to determine stakeholder needs for both research and extension. Impact assessment should be part of this planning effort. Performing as a successful extension faculty member while maintaining relationships outside of work is challenging and requires deliberate effort on the part of employees and supervisors to realize there is more to life than work. Some authors have referred to this as work-life balance, but it may be more helpful to think of it as work-life effectiveness. To do this, one needs to 1) define what success looks like, 2) set boundaries and maintain control including control of your schedule, and 3) find time to ensure your physical, emotional, and spiritual well-being are nurtured in addition to your professional development. In summary, extension careers can be challenging at times as demands and expectations of stakeholders, supervisors, and rigors of the tenure system create formidable obstacles. However, by keeping a focus on the priorities of the position and looking for synergy in research and extension work, they can actually be quite enjoyable and very rewarding.

Joint location, inventory, and preservation decisions for non-instantaneous deterioration items under delay in payments

NASA Astrophysics Data System (ADS)

Tsao, Yu-Chung

2016-02-01

This study models a joint location, inventory and preservation decision-making problem for non-instantaneous deteriorating items under delay in payments. An outside supplier provides a credit period to the wholesaler which has a distribution system with distribution centres (DCs). The non-instantaneous deteriorating means no deterioration occurs in the earlier stage, which is very useful for items such as fresh food and fruits. This paper also considers that the deteriorating rate will decrease and the reservation cost will increase as the preservation effort increases. Therefore, how much preservation effort should be made is a crucial decision. The objective of this paper is to determine the optimal locations and number of DCs, the optimal replenishment cycle time at DCs, and the optimal preservation effort simultaneously such that the total network profit is maximised. The problem is formulated as piecewise nonlinear functions and has three different cases. Algorithms based on piecewise nonlinear optimisation are provided to solve the joint location and inventory problem for all cases. Computational analysis illustrates the solution procedures and the impacts of the related parameters on decisions and profits. The results of this study can serve as references for business managers or administrators.

Semiconductor laser joint study program with Rome Laboratory

NASA Astrophysics Data System (ADS)

Schaff, William J.; Okeefe, Sean S.; Eastman, Lester F.

1994-09-01

A program to jointly study vertical-cavity surface emitting lasers (VCSEL) for high speed vertical optical interconnects (VOI) has been conducted under an ES&E between Rome Laboratory and Cornell University. Lasers were designed, grown, and fabricated at Cornell University. A VCSEL measurement laboratory has been designed, built, and utilized at Rome Laboratory. High quality VCSEL material was grown and characterized by fabricating conventional lateral cavity lasers that emitted at the design wavelength of 1.04 microns. The VCSEL's emit at 1.06 microns. Threshold currents of 16 mA at 4.8 volts were obtained for 30 microns diameter devices. Output powers of 5 mW were measured. This is 500 times higher power than from the light emitting diodes employed previously for vertical optical interconnects. A new form of compositional grading using a cosinusoidal function has been developed and is very successful for reducing diode series resistance for high speed interconnection applications. A flip-chip diamond package compatible with high speed operation of 16 VCSEL elements has been designed and characterized. A flip-chip device binding effort at Rome Laboratory was also designed and initiated. This report presents details of the one-year effort, including process recipes and results.

Often Difficult--But Worth It. Collaboration among Professionals.

ERIC Educational Resources Information Center

Walker, Joyce A.

1988-01-01

A joint effort between the Minnesota Extension Service and University of Minnesota School of Medicine produced a community-based research and educational program on stress, depression, and suicide prevention. The Teens in Distress program represents a successful collaborative effort and illustrates the potential problems when Extension…

Progress and achievements of R&D activities for the ITER vacuum vessel

NASA Astrophysics Data System (ADS)

Nakahira, M.; Takahashi, H.; Koizumi, K.; Onozuka, M.; Ioki, K.

2001-04-01

The Full Scale Sector Model Project, which was initiated in 1995 as one of the Seven Large Projects for ITER R&D, has been continued with the joint effort of the ITER Joint Central Team and the Japanese, Russian Federation and United States Home Teams. The fabrication of a full scale 18° toroidal sector, which is composed of two 9° sectors spliced at the port centre, was successfully completed in September 1997 with a dimensional accuracy of +/-3 mm for the total height and total width. Both sectors were shipped to the test site at the Japan Atomic Energy Research Institute and the integration test of the sectors was begun in October 1997. The integration test involves the adjustment of field joints, automatic narrow gap tungsten inert gas welding of field joints with splice plates and inspection of the joints by ultrasonic testing, as required for the initial assembly of the ITER vacuum vessel. This first demonstration of field joint welding and the performance test of the mechanical characteristics were completed in May 1998, and all the results obtained have satisfied the ITER design. In addition to these tests, integration with the midplane port extension fabricated by the Russian Home Team by using a fully remotized welding and cutting system developed by the US Home Team was completed in March 2000. The article describes the progress, achievements and latest status of the R&D activities for the ITER vacuum vessel.

History of San Marco

NASA Technical Reports Server (NTRS)

Caporale, A. J.

1968-01-01

A brief history is reported of the first San Marco project, a joint program of the United States and Italy. The Project was a three phase effort to investigate upper air density and associated ionosphere phenomena. The initial phase included the design and development of the spacecraft, the experiments, the launch complex, and a series of suborbital flights, from Wallops Island. The second phase, consisting of designing, fabricating, and testing a spacecraft for the first orbital mission, culminated in an orbital launch also from Wallops Island. The third phase consisted of further refining the experiments and spacecraft instrumentation and of establishing a full-bore scout complex in Kenya. The launch of San Marco B, in April 1967, from this complex into an equatorial orbit, concluded the initial San Marco effort.

Modular Software for Spacecraft Navigation Using the Global Positioning System (GPS)

NASA Technical Reports Server (NTRS)

Truong, S. H.; Hartman, K. R.; Weidow, D. A.; Berry, D. L.; Oza, D. H.; Long, A. C.; Joyce, E.; Steger, W. L.

1996-01-01

The Goddard Space Flight Center Flight Dynamics and Mission Operations Divisions have jointly investigated the feasibility of engineering modular Global Positioning SYSTEM (GPS) navigation software to support both real time flight and ground postprocessing configurations. The goals of this effort are to define standard GPS data interfaces and to engineer standard, reusable navigation software components that can be used to build a broad range of GPS navigation support applications. The paper discusses the GPS modular software (GMOD) system and operations concepts, major requirements, candidate software architecture, feasibility assessment and recommended software interface standards. In additon, ongoing efforts to broaden the scope of the initial study and to develop modular software to support autonomous navigation using GPS are addressed,

How joint torques affect hamstring injury risk in sprinting swing-stance transition.

PubMed

Sun, Yuliang; Wei, Shutao; Zhong, Yunjian; Fu, Weijie; Li, Li; Liu, Yu

2015-02-01

The potential mechanisms of hamstring strain injuries in athletes are not well understood. The study, therefore, was aimed at understanding hamstring mechanics by studying loading conditions during maximum-effort overground sprinting. Three-dimensional kinematics and ground reaction force data were collected from eight elite male sprinters sprinting at their maximum effort. Maximal isometric torques of the hip and knee were also collected. Data from the sprinting gait cycle were analyzed via an intersegmental dynamics approach, and the different joint torque components were calculated. During the initial stance phase, the ground reaction force passed anteriorly to the knee and hip, producing an extension torque at the knee and a flexion torque at the hip joint. Thus, the active muscle torque functioned to produce flexion torque at the knee and extension torque at the hip. The maximal muscle torque at the knee joint was 1.4 times the maximal isometric knee flexion torque. During the late swing phase, the muscle torque counterbalanced the motion-dependent torque and acted to flex the knee joint and extend the hip joint. The loading conditions on the hamstring muscles were similar to those of the initial stance phase. During both the initial stance and late swing phases, the large passive torques at both the knee and hip joints acted to lengthen the hamstring muscles. The active muscle torques generated mainly by the hamstrings functioned to counteract those passive effects. As a result, during sprinting or high-speed locomotion, the hamstring muscles may be more susceptible to high risk of strain injury during these two phases.

How Joint Torques Affect Hamstring Injury Risk in Sprinting Swing–Stance Transition

PubMed Central

SUN, YULIANG; WEI, SHUTAO; ZHONG, YUNJIAN; FU, WEIJIE; LI, LI; LIU, YU

2015-01-01

ABSTRACT Purpose The potential mechanisms of hamstring strain injuries in athletes are not well understood. The study, therefore, was aimed at understanding hamstring mechanics by studying loading conditions during maximum-effort overground sprinting. Methods Three-dimensional kinematics and ground reaction force data were collected from eight elite male sprinters sprinting at their maximum effort. Maximal isometric torques of the hip and knee were also collected. Data from the sprinting gait cycle were analyzed via an intersegmental dynamics approach, and the different joint torque components were calculated. Results During the initial stance phase, the ground reaction force passed anteriorly to the knee and hip, producing an extension torque at the knee and a flexion torque at the hip joint. Thus, the active muscle torque functioned to produce flexion torque at the knee and extension torque at the hip. The maximal muscle torque at the knee joint was 1.4 times the maximal isometric knee flexion torque. During the late swing phase, the muscle torque counterbalanced the motion-dependent torque and acted to flex the knee joint and extend the hip joint. The loading conditions on the hamstring muscles were similar to those of the initial stance phase. Conclusions During both the initial stance and late swing phases, the large passive torques at both the knee and hip joints acted to lengthen the hamstring muscles. The active muscle torques generated mainly by the hamstrings functioned to counteract those passive effects. As a result, during sprinting or high-speed locomotion, the hamstring muscles may be more susceptible to high risk of strain injury during these two phases. PMID:24911288

LANDSAT information for state planning

NASA Technical Reports Server (NTRS)

Faust, N. L.; Spann, G. W.

1977-01-01

The transfer of remote sensing technology for the digital processing of LANDSAT data to state and local agencies in Georgia and other southeastern states is discussed. The project consists of a series of workshops, seminars, and demonstration efforts, and transfer of NASA-developed hardware concepts and computer software to state agencies. Throughout the multi-year effort, digital processing techniques have been emphasized classification algorithms. Software for LANDSAT data rectification and processing have been developed and/or transferred. A hardware system is available at EES (engineering experiment station) to allow user interactive processing of LANDSAT data. Seminars and workshops emphasize the digital approach to LANDSAT data utilization and the system improvements scheduled for LANDSATs C and D. Results of the project indicate a substantially increased awareness of the utility of digital LANDSAT processing techniques among the agencies contracted throughout the southeast. In Georgia, several agencies have jointly funded a program to map the entire state using digitally processed LANDSAT data.

Communities of Practice: Professional Development Through Fostering Connections

NASA Astrophysics Data System (ADS)

Ali, N. A.; Raftery, C.; Shackleford, R.; Nelson, A.; Turney, D.

2015-11-01

A community of practice is a group of people informally bound together by shared expertise and passion for a joint enterprise. Through facilitated discussion, we will share best practices and research about communities of practice, and explore how they evolve as they grow. The target audience for this Special Interest Group session is Education and Public Outreach professionals who are interested in using communities of practice as a way to support the professional development of their audiences. This session will be of interest to people who want to learn more about communities of practice as well as those who are currently coordinating similar efforts. Participants will have the opportunity to share their challenges and success, as well as gain new ideas for the planning, implementation, and expansion of efforts. This session will be facilitated by the coordinators of NASA's SMD Heliophysics EPO Forum online community of practice for middle and high school science teachers.

The application of integrated knowledge-based systems for the Biomedical Risk Assessment Intelligent Network (BRAIN)

NASA Technical Reports Server (NTRS)

Loftin, Karin C.; Ly, Bebe; Webster, Laurie; Verlander, James; Taylor, Gerald R.; Riley, Gary; Culbert, Chris

1992-01-01

One of NASA's goals for long duration space flight is to maintain acceptable levels of crew health, safety, and performance. One way of meeting this goal is through BRAIN, an integrated network of both human and computer elements. BRAIN will function as an advisor to mission managers by assessing the risk of inflight biomedical problems and recommending appropriate countermeasures. Described here is a joint effort among various NASA elements to develop BRAIN and the Infectious Disease Risk Assessment (IDRA) prototype. The implementation of this effort addresses the technological aspects of knowledge acquisition, integration of IDRA components, the use of expert systems to automate the biomedical prediction process, development of a user friendly interface, and integration of IDRA and ExerCISys systems. Because C language, CLIPS and the X-Window System are portable and easily integrated, they were chosen ss the tools for the initial IDRA prototype.

Corporate ergonomics programme at Ford Motor Company.

PubMed

Joseph, Bradley S

2003-01-01

The use of ergonomic principles in automobile assembly and manufacturing operations has become an important part of a comprehensive health and safety process as well as an integral part of the engineering systems. Ford Motor Company has developed an ergonomics process to manage issues related to injury and illness (e.g., musculoskeletal diseases) and to ensure the appropriate use of human resources on the plant floor. The ergonomics programme uses joint labour and management teams to identify and evaluate jobs and develop and implement solutions. This paper summarises the efforts of the Ford Motor Company in implementing and maintaining the programme. Key strategies are outlined that provide important links to internal organisational units that are critical to fully utilise the ergonomics process. In addition, the paper outlines differences between proactive and reactive efforts and shows the importance of using the information generated by the initiatives for process improvement.

Program Validation: Four Case Studies. A Brief Report on Four Projects and Their Experiences Before the Joint Dissemination Review Panel.

ERIC Educational Resources Information Center

Taylor, Nancy, Ed.

In an effort to clearly illustrate the most effective approach when seeking Joint Dissemination Review Panel (JDRP) validation, this report describes four different educational programs. A program involving prekindergarten special students, and a project entailing a systems approach for disadvantaged elementary school students, were awarded…

Joint Institute for Nanoscience Annual Report 2004

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baer, Donald R.; Campbell, Charles

Due to the inherently interdisciplinary nature of nanoscience and nanotechnology, research in this arena is often significantly enhanced through creative cooperative activities. The Joint Institute for Nanoscience (JIN) is a venture of the University of Washington (UW) and Pacific Northwest National Laboratory (PNNL) to encourage and enhance high impact and high quality nanoscience and nanotechnology research that leverages the strengths and capabilities of both institutions, and to facilitate education in these areas. This report summarizes JIN award activities that took place during fiscal year 2004 and provides a historical list of JIN awardees, their resulting publications, and JIN-related meetings. Majormore » portions of the JIN efforts and resources are dedicated to funding graduate students and postdoctoral research associates to perform research in collaborations jointly directed by PNNL staff scientists and UW professors. JIN fellowships are awarded on the basis of applications that include research proposals. They have been very successful in expanding collaborations between PNNL and UW, which have led to many excellent joint publications and presentations and enhanced the competitiveness of both institutions for external grant funding. JIN-based interactions are playing a significant role in creating new research directions and reshaping existing research programs at both the UW and PNNL. The JIN also co-sponsors workshops on Nanoscale Science and Technology, four of which have been held in Seattle and one in Richland. In addition to involving PNNL staff in various UW nanoscience courses and seminars, a National Science Foundation grant, Development of UW-PNL Collaborative Curriculums in Nano-Science and Technology, has allowed the development of three intensive short courses that are taught by UW faculty, PNNL staff, and faculty from other institutions, including Washington State University, the University of Idaho, Stanford University, and the University of Alaska. The JIN agreement recognizes that cooperation beyond UW and PNNL is highly valuable. Starting in early 2003, efforts were initiated to form a regional communication link called the Northwest Nanoscience and Nanotechnology Network (N4). In concept, N4 is a tool to encourage communication and help identify regional resources and nanoscience and technology activities.« less

Satellite Technology Demonstration; Executive Report.

ERIC Educational Resources Information Center

Federation of Rocky Mountain States, Inc., Denver, CO.

The Federation of Rocky Mountain States and the Satellite Technology Demonstration project (STD) have collaborated in an effort to provide low cost information delivery to rural areas of the Rockies. Though the goals and the financial support of this joint effort were initially confused, sites have now been selected, the communications technology…

Extrabudgetary Funding and Institutional Relationships between Higher Education, Industry, and Social Partners.

ERIC Educational Resources Information Center

Schulte, Peter

2003-01-01

Describes one German university's efforts over 10 years to institutionalize relationships with small- and mid-sized industry and local enterprises, thereby increasing extra-budgetary funding for applied research projects. These joint efforts offer students the opportunity to acquire both theoretical knowledge and practical training during their…

An Example for Integrated Gas Turbine Engine Testing and Analysis Using Modeling and Simulation

DTIC Science & Technology

2006-12-01

USAF Academy in a joint test and analysis effort of the F109 turbofan engine. This process uses a swirl investigation as a vehicle to exercise and...test and analysis effort of the F109 turbofan engine. This process uses a swirl investigation as a vehicle to exercise and demonstrate the approach...test and analysis effort of the F109 turbofan engine, an effort which uses a swirl investigation as a vehicle to exercise and demonstrate the

2007 Joint Service Power Expo: Power and Energy Independence for Warfighters

DTIC Science & Technology

2007-04-26

Technology benefits and cost LiFePO4 Development LiFePO4 Development ● SAFT initiated work on LiFePO4 under a developmental program with Army...life and improvement ● SAFT is continuing the LiFePO4 work under US Army MANTECH effort. Very High Power cells with the LiFePO4 cathode have been...supplier of LiFePO4 – Phostech/Sud-Chemie. Cell VL10Fe VL12V Cathode LiFePO4 NCA Nominal Voltage (V) 3.3 3.6 Nominal Capacity at C rate (Ah) 10 12 V = f

Materials technology programs in support of a mercury Rankine space power system

NASA Technical Reports Server (NTRS)

Stone, P. L.

1973-01-01

A large portion of the materials technology is summarized that was generated in support of the development of a mercury-rankine space power system (SNAP-8). The primary areas of investigation are: (1) the compatibility of various construction materials with the liquid metals mercury and NaK, (2) the mechanical properties of unalloyed tantalum, and (3) the development of refractory metal/austenitic stainless steel tubing and transition joints. The primary results, conclusions, and state of technology at the completion of this effort for each of these areas are summarized. Results of possible significance to other applications are highlighted.

A stochastic Iwan-type model for joint behavior variability modeling

NASA Astrophysics Data System (ADS)

Mignolet, Marc P.; Song, Pengchao; Wang, X. Q.

2015-08-01

This paper focuses overall on the development and validation of a stochastic model to describe the dissipation and stiffness properties of a bolted joint for which experimental data is available and exhibits a large scatter. An extension of the deterministic parallel-series Iwan model for the characterization of the force-displacement behavior of joints is first carried out. This new model involves dynamic and static coefficients of friction differing from each other and a broadly defined distribution of Jenkins elements. Its applicability is next investigated using the experimental data, i.e. stiffness and dissipation measurements obtained in harmonic testing of 9 nominally identical bolted joints. The model is found to provide a very good fit of the experimental data for each bolted joint notwithstanding the significant variability of their behavior. This finding suggests that this variability can be simulated through the randomization of only the parameters of the proposed Iwan-type model. The distribution of these parameters is next selected based on maximum entropy concepts and their corresponding parameters, i.e. the hyperparameters of the model, are identified using a maximum likelihood strategy. Proceeding with a Monte Carlo simulation of this stochastic Iwan model demonstrates that the experimental data fits well within the uncertainty band corresponding to the 5th and 95th percentiles of the model predictions which well supports the adequacy of the modeling effort.

Utilization of an interorganizational network analysis to evaluate the development of community capacity among a community-academic partnership.

PubMed

Clark, Heather R; Ramirez, Albert; Drake, Kelly N; Beaudoin, Christopher E; Garney, Whitney R; Wendel, Monica L; Outley, Corliss; Burdine, James N; Player, Harold D

2014-01-01

Following a community health assessment the Brazos Valley Health Partnership (BVHP) organized to address fragmentation of services and local health needs. This regional partnership employs the fundamental principles of community-based participatory research, fostering an equitable partnership with the aim of building community capacity to address local health issues. This article describes changes in relationships as a result of capacity building efforts in a community-academic partnership. Growth in network structure among organizations is hypothesized to be indicative of less fragmentation of services for residents and increased capacity of the BVHP to collectively address local health issues. Each of the participant organizations responded to a series of questions regarding its relationships with other organizations. Each organization was asked about information sharing, joint planning, resource sharing, and formal agreements with other organizations. The network survey has been administered 3 times between 2004 and 2009. Network density increased for sharing information and jointly planning events. Growth in the complexity of relationships was reported for sharing tangible resources and formal agreements. The average number of ties between organizations as well as the strength of relationships increased. This study provides evidence that the community capacity building efforts within these communities have contributed to beneficial changes in interorganizational relationships. Results from this analysis are useful for understanding how a community partnership's efforts to address access to care can strengthen a community's capacity for future action. Increased collaboration also leads to new assets, resources, and the transfer of knowledge and skills.

Microarthroscopy System With Image Processing Technology Developed for Minimally Invasive Surgery

NASA Technical Reports Server (NTRS)

Steele, Gynelle C.

2001-01-01

In a joint effort, NASA, Micro Medical Devices, and the Cleveland Clinic have developed a microarthroscopy system with digital image processing. This system consists of a disposable endoscope the size of a needle that is aimed at expanding the use of minimally invasive surgery on the knee, ankle, and other small joints. This device not only allows surgeons to make smaller incisions (by improving the clarity and brightness of images), but it gives them a better view of the injured area to make more accurate diagnoses. Because of its small size, the endoscope helps reduce physical trauma and speeds patient recovery. The faster recovery rate also makes the system cost effective for patients. The digital image processing software used with the device was originally developed by the NASA Glenn Research Center to conduct computer simulations of satellite positioning in space. It was later modified to reflect lessons learned in enhancing photographic images in support of the Center's microgravity program. Glenn's Photovoltaic Branch and Graphics and Visualization Lab (G-VIS) computer programmers and software developers enhanced and speed up graphic imaging for this application. Mary Vickerman at Glenn developed algorithms that enabled Micro Medical Devices to eliminate interference and improve the images.

Genetic Epidemiology of Cigarette Smoke–Induced Lung Disease

PubMed Central

2012-01-01

Chronic obstructive pulmonary disease (COPD) and lung cancer represent two diseases that share a strong risk factor in smoking, and COPD increases risk of lung cancer even after adjusting for the effects of smoking. These diseases not only occur jointly within an individual but also there is evidence of shared occurrence within families. Understanding the genetic contributions to these diseases, both individually and jointly, is needed to identify the highest risk group for screening and targeted prevention, as well as aiding in the development of targeted treatments. The chromosomal regions that have been identified as being associated either jointly or independently with lung cancer, COPD, nicotine addiction, and lung function are presented. Studies jointly measuring genetic variation in lung cancer and COPD have been limited by the lack of detailed COPD diagnosis and severity data in lung cancer populations, the lack of lung cancer–specific phenotypes (histology and tumor markers) in COPD populations, and the lack of inclusion of minorities. African Americans, who smoke fewer cigarettes per day and have different linkage disequilibrium and disease patterns than whites, and Asians, also with different patterns of exposure to lung carcinogens and linkage patterns, will provide invaluable information to better understand shared and independent genetic contributions to lung cancer and COPD to more fully define the highest risk group of individuals who will most benefit from screening and to develop molecular signatures to aid in targeted treatment and prevention efforts. PMID:22550237

Pressure induced phase transitions studies using advanced synchrotron techniques

NASA Astrophysics Data System (ADS)

Liu, Haozhe; Liu, Lisa; Zhao, Jinggeng; HIT Overseas Collaborative Base at Argonne Collaboration

2013-06-01

In this presentation, the joint effort on high pressure research through program of Harbin Institute of Technology (HIT) Overseas Collaborative Base at Argonne will be introduced. Selected research projects on pressure induced phase transitions at room temperature and high/low temperature conditions, such as A2B3 type topological insulators, iron arsenide superconductors, piezoelectric/ferroelectric materials, ABO3 type single crystals and metallic glasses, will be presented. Recent development on imaging and diffraction tomography techniques in diamond anvil cell will be reviewed as well.

AISI/DOE Advanced Process Control Program Vol. 3 of 6 Microstructure Engineering in Hot Strip Mills, Part 1 of 2: Integrated Mathematical Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.K. Brimacombe; I.V. Samarasekera; E.B. Hawbolt

1999-07-31

This report describes the work of developing an integrated model used to predict the thermal history, deformation, roll forces, microstructural evolution and mechanical properties of steel strip in a hot-strip mill. This achievement results from a joint research effort that is part of the American Iron and Steel Institute's (AIS) Advanced Process Control Program, a collaboration between the U.S. DOE and fifteen North American Steelmakers.

Multi-Model Ensemble Wake Vortex Prediction

NASA Technical Reports Server (NTRS)

Koerner, Stephan; Holzaepfel, Frank; Ahmad, Nash'at N.

2015-01-01

Several multi-model ensemble methods are investigated for predicting wake vortex transport and decay. This study is a joint effort between National Aeronautics and Space Administration and Deutsches Zentrum fuer Luft- und Raumfahrt to develop a multi-model ensemble capability using their wake models. An overview of different multi-model ensemble methods and their feasibility for wake applications is presented. The methods include Reliability Ensemble Averaging, Bayesian Model Averaging, and Monte Carlo Simulations. The methodologies are evaluated using data from wake vortex field experiments.

Application of Pi Preform Composite Joints in Fabrication of NASA Composite Crew Module Demonstration Structure

NASA Technical Reports Server (NTRS)

Higgins, John E.; Pelham, Larry

2008-01-01

This paper will describe unique and extensive use of pre-woven and impregnated pi cross-sections in fabrication of a carbon composite demonstration structure for the Composite Crew Module (CCM) Program. The program is managed by the NASA Safety and Engineering Center with participants from ten NASA Centers and AFRL. Multiple aerospace contractors are participating in the design development, tooling and fabrication effort as well. The goal of the program is to develop an agency wide design team for composite habitable spacecraft. The specific goals for this development project are: a) To gain hands on experience in design, building and testing a composite crew module. b) To validate key assumptions by resolving composite spacecraft design details through fabrication and testing of hardware. This paper will focus on the design and fabrication issues supporting selection of the Lockheed Martin patented Pi pre-form to provide sound composite joints a numerous locations in the structure. This abstract is based on Preliminary Design data. The final design will continue to evolve through the fall of 2007 with fabrication mostly completed by conference date.

Activities of UAH

NASA Technical Reports Server (NTRS)

Li, Ning

2000-01-01

From its start in December 1996, the Cooperative Agreement allowed that some tasks could be performed primarily by UAH, some primarily by MSFC and some in a joint manner. The detailed distribution of effort has evolved in a pragmatic fashion, with each organization focusing on those tasks that seemed most urgent and for which appropriate capabilities existed. The final, all-up experiments were envisioned as a very careful measurement process carried out jointly using components developed at both UAH and MSFC. The total project began with an air of optimism that the necessary apparatus for the adopted objectives could be quickly and easily assembled. Not surprisingly, technological difficulties were encountered by all parties and it has proven impossible to complete the challenging experiments in the term of this cooperative agreement. The UAH accomplishments toward the ultimate experiments are reported here in a taskwise manner.

Integrating research and management to conserve wildfowl (Anatidae) and wetlands in the Mississippi Alluvial Valley, U.S.A

USGS Publications Warehouse

Reinecke, K.J.; Loesch, C.R.; Birkan, Marcel

1996-01-01

Efforts to conserve winter habitat for wildfowl, Anatidae, in the alluvial valley of the lower Mississippi River, U.S.A., are directed by the Lower Mississippi Valley (LMV) Joint Venture of the North American Waterfowl Management Plan (NA WMP). The Joint Venture is based on a biological framework developed through cooperative planning by wildfowl researchers and managers. Important elements of the framework include: (1) numeric population goals, (2) assumptions about potential limiting factors, (3) explicit relationships between wildfowl abundance and habitat characteristics, (4) numeric foraging habitat goals, and (5) criteria for evaluating success. The population goal of the Joint Venture for the Mississippi Alluvial Valley (MA V) is to enable 4.3 million ducks to, survive winter and join continental breeding populations in spring. Currently, available data suggest that foraging habitat is the primary factor limiting duck populations in the MA II. To establish a goal for foraging habitat, we assumed the length of the wintering period is 110 days and calculated that a population of 4.3 million breeding ducks (plus 15% to account for winter mortality) would need 546 million duck-days of food in the preceding winter. Then, we used estimates of daily energy requirements, food densities, and food energy values to calculate the carrying capacity or number of duck-days of food available in the three primary foraging habitats in the MAV (flooded croplands, forested wetlands, and moist-soil wetlands). Thus, availability of foraging habitat can be used as a criterion for evaluating success of the Joint Venture if accurate inventories of foraging habitat can be conducted. Development of an explicit biological framework for the Joint Venture enabled wildfowl managers and researchers to establish specific objectives for management of foraging habitat and identify priority problems requiring further study.

Differential limb loading in miniature pigs (Sus scrofa domesticus): a test of chondral modeling theory

PubMed Central

Congdon, Kimberly A.; Hammond, Ashley S.; Ravosa, Matthew J.

2012-01-01

SUMMARY Variation in mechanical loading is known to influence chondrogenesis during joint formation. However, the interaction among chondrocyte behavior and variation in activity patterns is incompletely understood, hindering our knowledge of limb ontogeny and function. Here, the role of endurance exercise in the development of articular and physeal cartilage in the humeral head was examined in 14 miniature swine (Sus scrofa domesticus). One group was subjected to graded treadmill running over a period of 17 weeks. A matched sedentary group was confined to individual pens. Hematoxylin and eosin staining was performed for histomorphometry of cartilage zone thickness, chondrocyte count and cell area, with these parameters compared multivariately between exercised and sedentary groups. Comparisons were also made with femora from the same sample, focusing on humerus–femur differences between exercised and sedentary groups, within-cohort comparisons of humerus–femur responses and correlated changes within and across joints. This study shows conflicting support for the chondral modeling theory. The humeral articular cartilage of exercised pigs was thinner than that of sedentary pigs, but their physeal cartilage was thicker. While articular and physeal cartilage demonstrated between-cohort differences, humeral physeal cartilage exhibited load-induced responses of greater magnitude than humeral articular cartilage. Controlling for cohort, the humerus showed increased chondrocyte mitosis and cell area, presumably due to relatively greater loading than the femur. This represents the first known effort to evaluate chondral modeling across multiple joints from the same individuals. Our findings suggest the chondral response to elevated loading is complex, varying within and among joints. This has important implications for understanding joint biomechanics and development. PMID:22496283

US Carrier Strike and the Mediterranean, 1970-89 - Lessons in Littoral Crisis Response for the United Kingdom’s Joint Expeditionary Force

DTIC Science & Technology

2014-03-27

east of Suez could apply equally to her heightened interest in the Mediterranean: 29 See Stephen C. Calleya,”Bridging History and Future Security...diplomacy and military effort in the Libyan crisis.4 Rising to that ambition, the carriers - a joint force in steel, treasure and equities - have the

An Approach to the Internationalisation of the Curriculum: Sino-British Joint Efforts for Three Online Courses

ERIC Educational Resources Information Center

Yawan, Li; Ying, Li

2011-01-01

With a view to facilitating good practice and enhancing further exchanges and collaboration with the Open University UK, the Open University of China initiated a joint programme of training to offer online tutors and academic management staff three courses: Student Support, Tutoring On-line, and Course Design. The programme brought in not only a…

Workshop Report: Joint Requirements. Oversight Council Process.

DTIC Science & Technology

1996-02-28

provides media for professional exchange and peer criticism among students, theoreticians, practitioners, and users of military operations research. These... exchange of ideas and methods. involvement in the annual Joint Warfare Inter- Subsequent efforts could include multiple operability Demonstrations (JWID...forums for exchange of ideas at the working level, clear, visible relations but studies and analysis opportunities as well. between the JWCAs need to

Politics as Usual: The Joint Committee on Printing and Executive Agency Publishing, 1919-1921.

ERIC Educational Resources Information Center

Walters, John

1993-01-01

Provides an interpretation of the U.S. Congress Joint Committee on Printing (JCP) efforts to control departmental publishing from 1919 to 1921. Topics addressed include the JCP and the War Department, the role of the JCP in the defeat of the League of Nations, and the issue of separation of powers. (126 references) (LRW)

National Positioning, Navigation, and Timing Architecture Study

NASA Astrophysics Data System (ADS)

van Dyke, K.; Vicario, J.; Hothem, L.

2007-12-01

The purpose of the National Positioning, Navigation and Timing (PNT) Architecture effort is to help guide future PNT system-of-systems investment and implementation decisions. The Assistant Secretary of Defense for Networks and Information Integration and the Under Secretary of Transportation for Policy sponsored a National PNT Architecture study to provide more effective and efficient PNT capabilities focused on the 2025 timeframe and an evolutionary path for government provided systems and services. U.S. Space-Based PNT Policy states that the U.S. must continue to improve and maintain GPS, augmentations to GPS, and back-up capabilities to meet growing national, homeland, and economic security needs. PNT touches almost every aspect of people´s lives today. PNT is essential for Defense and Civilian applications ranging from the Department of Defense´s Joint network centric and precision operations to the transportation and telecommunications sectors, improving efficiency, increasing safety, and being more productive. Absence of an approved PNT architecture results in uncoordinated research efforts, lack of clear developmental paths, potentially wasteful procurements and inefficient deployment of PNT resources. The national PNT architecture effort evaluated alternative future mixes of global (space and non space-based) and regional PNT solutions, PNT augmentations, and autonomous PNT capabilities to address priorities identified in the DoD PNT Joint Capabilities Document (JCD) and civil equivalents. The path to achieving the Should-Be architecture is described by the National PNT Architecture's Guiding Principles, representing an overarching Vision of the US' role in PNT, an architectural Strategy to fulfill that Vision, and four Vectors which support the Strategy. The National PNT Architecture effort has developed nineteen recommendations. Five foundational recommendations are tied directly to the Strategy while the remaining fourteen individually support one of the Vectors, as will be described in this presentation. The results of this effort will support future decisions of bodies such as the DoD PNT and Civil Pos/Nav Executive Committees, as well as the National Space-Based PNT Executive Committee (EXCOM).

Grease-Resistant O Rings for Joints in Solid Rocket Motors

NASA Technical Reports Server (NTRS)

Harvey, Albert R.; Feldman, Harold

2003-01-01

There is a continuing effort to develop improved O rings for sealing joints in solid-fuel rocket motors. Following an approach based on the lessons learned in the explosion of the space shuttle Challenger, investigators have been seeking O-ring materials that exhibit adequate resilience for effective sealing over a broad temperature range: What are desired are O rings that expand far and fast enough to maintain seals, even when metal sealing surfaces at a joint move slightly away from each other shortly after ignition and the motor was exposed to cold weather before ignition. Other qualities desired of the improved O rings include adequate resistance to ablation by hot rocket gases and resistance to swelling when exposed to hydrocarbon-based greases used to protect some motor components against corrosion. Five rubber formulations two based on a fluorosilicone polymer and three based on copolymers of epichlorohydrin with ethylene oxide were tested as candidate O-ring materials. Of these, one of the epichlorohydrin/ethylene oxide formulations was found to offer the closest to the desired combination of properties and was selected for further evaluation.

Large-scale assessment of soil erosion in Africa: satellites help to jointly account for dynamic rainfall and vegetation cover

NASA Astrophysics Data System (ADS)

Vrieling, Anton; Hoedjes, Joost C. B.; van der Velde, Marijn

2015-04-01

Efforts to map and monitor soil erosion need to account for the erratic nature of the soil erosion process. Soil erosion by water occurs on sloped terrain when erosive rainfall and consequent surface runoff impact soils that are not well-protected by vegetation or other soil protective measures. Both rainfall erosivity and vegetation cover are highly variable through space and time. Due to data paucity and the relative ease of spatially overlaying geographical data layers into existing models like USLE (Universal Soil Loss Equation), many studies and mapping efforts merely use average annual values for erosivity and vegetation cover as input. We first show that rainfall erosivity can be estimated from satellite precipitation data. We obtained average annual erosivity estimates from 15 yr of 3-hourly TRMM Multi-satellite Precipitation Analysis (TMPA) data (1998-2012) using intensity-erosivity relationships. Our estimates showed a positive correlation (r = 0.84) with long-term annual erosivity values of 37 stations obtained from literature. Using these TMPA erosivity retrievals, we demonstrate the large interannual variability, with maximum annual erosivity often exceeding two to three times the mean value, especially in semi-arid areas. We then calculate erosivity at a 10-daily time-step and combine this with vegetation cover development for selected locations in Africa using NDVI - normalized difference vegetation index - time series from SPOT VEGETATION. Although we do not integrate the data at this point, the joint analysis of both variables stresses the need for joint accounting for erosivity and vegetation cover for large-scale erosion assessment and monitoring.

Brazil on the Rise: Implications on U.S. Policies

DTIC Science & Technology

2012-04-01

Brazilian Joint Counternarcotics Opportunity………….6 U.S. Efforts in Bolivia Brazil Fills the U.S. Counternarcotics Gap in Bolivia Future for...efforts Brazil has undertaken with Bolivia, one can see how a multilateral effort in the region yields better results to address the situation...form of Brazil. Brazil Fills the U.S. Counternarcotics Gap in Bolivia In 1998 there was reportedly little to no narcotics transiting Brazil, and

New role for space station—Enhanced cooperation with Russia?

NASA Astrophysics Data System (ADS)

Leath, Audrey T.

The Clinton administration's recent discussions with Russia on enhanced space cooperation and a possible joint space station prompted a two-part hearing by the House Science Subcommittee on Space, held on October 6 and 14. Subcommittee members, citing rumors and news stories about a joint station, questioned Presidential Science Advisor Jack Gibbons and NASA Administrator Daniel Goldin on the status of the proposed cooperation and heard from additional witnesses regarding the feasibility of and support for the concept.Gibbons reassured subcommittee members that no decision has yet been made on Russian cooperation, and that Congress would be consulted in the process. He explained that, after the Vancouver Summit, establishment of a Joint Commission headed by Vice President Gore and Russian Prime Minister Chernomyrdin provided an opportunity for enhanced cooperation in space, as well as in such other areas as energy, nuclear safety, the environment, business development, science and technology, and defense diversification. Gibbons testified that the study of a cooperative station program took place concurrently with NASA's work on defining the redesigned U.S. space station, now being referred to as “Alpha.” He affirmed that while Alpha's modular design made it adaptable to a joint effort, it could “be built independent of any Russian participation.”

Space Suit Joint Torque Testing

NASA Technical Reports Server (NTRS)

Valish, Dana J.

2011-01-01

In 2009 and early 2010, a test was performed to quantify the torque required to manipulate joints in several existing operational and prototype space suits in an effort to develop joint torque requirements appropriate for a new Constellation Program space suit system. The same test method was levied on the Constellation space suit contractors to verify that their suit design meets the requirements. However, because the original test was set up and conducted by a single test operator there was some question as to whether this method was repeatable enough to be considered a standard verification method for Constellation or other future space suits. In order to validate the method itself, a representative subset of the previous test was repeated, using the same information that would be available to space suit contractors, but set up and conducted by someone not familiar with the previous test. The resultant data was compared using graphical and statistical analysis and a variance in torque values for some of the tested joints was apparent. Potential variables that could have affected the data were identified and re-testing was conducted in an attempt to eliminate these variables. The results of the retest will be used to determine if further testing and modification is necessary before the method can be validated.

Five years from the great 2010 Tsunami in Chile: learning from multi-hazard disasters and improving resileincy

NASA Astrophysics Data System (ADS)

Cienfuegos, R.; Gonzalez, G.; Repetto, P.; Cipriano, A.; Moris, R.; Catalan, P. A.; Guic, E.; Martin, J. C. D. L. L.

2016-12-01

The Research Center for Integrated Natural Hazards Management (CIGIDEN) has developed in recent years (supported by the Fondap/Conicyt Excellence in research center's program) active efforts to connect science and public institutions in charge of disaster management in Chile. We have been able to reach in particular the National Emergency Office (ONEMI) and the National Hydrographic and Oceanographic Naval Service (SHOA), and develop joint specific programs that have been mutually beneficial both for research enrichment and the operation of the emergency response system. Through these efforts, also supplemented by other Chilean and International research institutions, we analyzed together issues and challenges from the systemic failure experienced by the emergency system in Chile after the 2010 earthquake and tsunami. In this talk we will review some of the main collaboration actions and their outcomes, connecting them to the extreme events that impacted Chile in 2015 (earthquakes, tsunamis, storm waves, and flash floods). In particular we will describe the effort that CIGIDEN has developed i) with ONEMI in developing instruments to assess community preparedness and awareness and to understand tsunami evacuation behaviors; and ii) with SHOA to develop a new Integrated Decision Support System for Tsunami alerting that is being transferred to SHOA in September 2015, and was successfully tested offline during the September 16th, 2015, tsunami.

Report Summarizing the Effort Required to Initiate Welding of Irradiated Materials within the Welding Cubicle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frederick, Greg; Sutton, Benjamin J.; Tatman, Jonathan K.

The advanced welding facility within a hot cell at the Radiochemical Engineering Development Center of Oak Ridge National Laboratory (ORNL), which has been jointly funded by the U.S. Department of Energy (DOE), Office of Nuclear Energy, Light Water Reactor Sustainability Program and the Electric Power Research Institute, Long Term Operations Program and the Welding and Repair Technology Center, is in the final phase of development. Research and development activities in this facility will involve direct testing of advanced welding technologies on irradiated materials in order to address the primary technical challenge of helium induced cracking that can arise when conventionalmore » fusion welding techniques are utilized on neutron irradiated stainless steels and nickel-base alloys. This report details the effort that has been required since the beginning of fiscal year 2017 to initiate welding research and development activities on irradiated materials within the hot cell cubicle, which houses welding sub-systems that include laser beam welding (LBW) and friction stir welding (FSW) and provides material containment within the hot cell.« less

Preparing technicians for engineering materials technology

NASA Technical Reports Server (NTRS)

Jacobs, James A.; Metzloff, Carlton H.

1990-01-01

A long held principle is that for every engineer and scientist there is a need for ten technicians to maximize the efficiency of the technology team for meeting needs of industry and government. Developing an adequate supply of technicians to meet the requirements of the materials related industry will be a challenge and difficult to accomplish. A variety of agencies feel the need and wish to support development of engineering materials technology programs. In a joint effort among Battelle Laboratories, the Department of Energy (DOE) and Northwest College and University Association for Science (NORCUS), the development of an engineering materials technology program for vocational programs and community colleges for the Pacific Northwest Region was recently completed. This effort has implications for a national model. The model Associate of Applied Science degree in Engineering Materials Technology shown provides a general structure. It purposely has course titles which need delimiting while also including a core of courses necessary to develop cognitive, affective and psychomotor skills with the underlining principles of math, science and technology so students have job entry skills, and so that students can learn about and adapt to evolving technology.

What is the price for the Duchenne gait pattern in patients with cerebral palsy?

PubMed

Salami, Firooz; Niklasch, Mirjam; Krautwurst, Britta K; Dreher, Thomas; Wolf, Sebastian I

2017-10-01

Duchenne gait is characterized by trunk lean towards the affected stance limb with the pelvis stable or elevated on the swinging limb side during single limb stance phase. We assessed the relationship between hip abduction moments and trunk kinetics in patients with cerebral palsy showing excessive lateral trunk motion. Data of 18 subjects with bilateral spastic cerebral palsy (CP) and 20 aged matched typically developing subjects (TD) were collected retrospectively. Criteria for patient selection were barefoot walking without aid presenting with excessive lateral trunk motion. Subjects had been monitored by conventional 3D gait analysis of the lower extremity including four markers for monitoring trunk motion. Post-hoc, a generic musculoskeletal full body model (OpenSim 3.3) assuming a rigid trunk articulated to the pelvis by a single ball joint was applied for analyzing joint kinematics and kinetics of the lower limb joints including this spine joint. Joint angle ranges of motion, maximum joint moments and powers in the frontal plane as well as mechanical work were calculated and averaged within groups showing prominent differences between groups in all parameters. To the best of our knowledge, this is the first work explicitly looking into the kinetics of Duchenne gait in patients with CP, clinically known as compensation for unloading hip abductor muscles. The results show that excessive lateral trunk motion may indeed be an extremely effective compensation mechanism to unload the hip abductors in single limb stance but for the price of a drastic increase in demand on trunk muscle effort and work. Copyright © 2017 Elsevier B.V. All rights reserved.

Development of ASTM Standard for SiC-SiC Joint Testing Final Scientific/Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacobsen, George; Back, Christina

2015-10-30

As the nuclear industry moves to advanced ceramic based materials for cladding and core structural materials for a variety of advanced reactors, new standards and test methods are required for material development and licensing purposes. For example, General Atomics (GA) is actively developing silicon carbide (SiC) based composite cladding (SiC-SiC) for its Energy Multiplier Module (EM2), a high efficiency gas cooled fast reactor. Through DOE funding via the advanced reactor concept program, GA developed a new test method for the nominal joint strength of an endplug sealed to advanced ceramic tubes, Fig. 1-1, at ambient and elevated temperatures called themore » endplug pushout (EPPO) test. This test utilizes widely available universal mechanical testers coupled with clam shell heaters, and specimen size is relatively small, making it a viable post irradiation test method. The culmination of this effort was a draft of an ASTM test standard that will be submitted for approval to the ASTM C28 ceramic committee. Once the standard has been vetted by the ceramics test community, an industry wide standard methodology to test joined tubular ceramic components will be available for the entire nuclear materials community.« less

Probabilistic accident consequence uncertainty analysis -- Uncertainty assessment for deposited material and external doses. Volume 2: Appendices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goossens, L.H.J.; Kraan, B.C.P.; Cooke, R.M.

1997-12-01

The development of two new probabilistic accident consequence codes, MACCS and COSYMA, was completed in 1990. These codes estimate the consequence from the accidental releases of radiological material from hypothesized accidents at nuclear installations. In 1991, the US Nuclear Regulatory Commission and the Commission of the European Communities began cosponsoring a joint uncertainty analysis of the two codes. The ultimate objective of this joint effort was to systematically develop credible and traceable uncertainty distributions for the respective code input variables. A formal expert judgment elicitation and evaluation process was identified as the best technology available for developing a library ofmore » uncertainty distributions for these consequence parameters. This report focuses on the results of the study to develop distribution for variables related to the MACCS and COSYMA deposited material and external dose models. This volume contains appendices that include (1) a summary of the MACCS and COSYMA consequence codes, (2) the elicitation questionnaires and case structures, (3) the rationales and results for the panel on deposited material and external doses, (4) short biographies of the experts, and (5) the aggregated results of their responses.« less

A simple 5-DOF walking robot for space station application

NASA Technical Reports Server (NTRS)

Brown, H. Benjamin, Jr.; Friedman, Mark B.; Kanade, Takeo

1991-01-01

Robots on the NASA space station have a potential range of applications from assisting astronauts during EVA (extravehicular activity), to replacing astronauts in the performance of simple, dangerous, and tedious tasks; and to performing routine tasks such as inspections of structures and utilities. To provide a vehicle for demonstrating the pertinent technologies, a simple robot is being developed for locomotion and basic manipulation on the proposed space station. In addition to the robot, an experimental testbed was developed, including a 1/3 scale (1.67 meter modules) truss and a gravity compensation system to simulate a zero-gravity environment. The robot comprises two flexible links connected by a rotary joint, with a 2 degree of freedom wrist joints and grippers at each end. The grippers screw into threaded holes in the nodes of the space station truss, and enable it to walk by alternately shifting the base of support from one foot (gripper) to the other. Present efforts are focused on mechanical design, application of sensors, and development of control algorithms for lightweight, flexible structures. Long-range research will emphasize development of human interfaces to permit a range of control modes from teleoperated to semiautonomous, and coordination of robot/astronaut and multiple-robot teams.

Expert system for adhesive selection of composite material joints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, R.B.; Vanderveldt, H.H.

The development of composite joining is still in its infancy and much is yet to be learned. Consequently, this field is developing rapidly and new advances occur with great regularity. The need for up-to-date information and expertise in engineering and planning of composite materials, especially in critical applications, is acute. The American Joining Institute`s (AJI) development of JOINEXCELL (an off-line intelligent planner for joining composite materials) is an intelligent engineering/planning software system that incorporates the knowledge of several experts which can be expanded as these developments occur. Phase I effort of JOINEXCELL produced an expert system for adhesive selection, JOINADSELECT,more » for composite material joints. The expert system successfully selects from over 26 different adhesive families for 44 separate material types and hundreds of application situations. Through a series of design questions the expert system selects the proper adhesive for each particular design. Performing this {open_quotes}off-line{close_quotes} engineering planning by computer allows the decision to be made with full knowledge of the latest information about materials and joining procedures. JOINADSELECT can greatly expedite the joining design process, thus yielding cost savings.« less

Dark Skies Rangers

NASA Astrophysics Data System (ADS)

Doran, Rosa

2015-08-01

Creating awareness about the importance of the protection of our dark skies is the main goal of the Dark Skies Rangers project, a joint effort from the NOAO and the Galileo Teacher Training Program. Hundreds of schools and thousands of students have been reached by this program. We will focus in particular on the experience being developed in Portugal where several municipalities have now received street light auditing produced by students with suggestions on how to enhance the energy efficiency of illumination of specific urban areas. In the International Year of Light we are investing our efforts in exporting the successful Portuguese experience to other countries. The recipe is simple: train teachers, engage students, foster the participation of local community and involve local authorities in the process. In this symposium we hope to draft the cookbook for the near future.

Optimal coordination of maximal-effort horizontal and vertical jump motions – a computer simulation study

PubMed Central

Nagano, Akinori; Komura, Taku; Fukashiro, Senshi

2007-01-01

Background The purpose of this study was to investigate the coordination strategy of maximal-effort horizontal jumping in comparison with vertical jumping, using the methodology of computer simulation. Methods A skeletal model that has nine rigid body segments and twenty degrees of freedom was developed. Thirty-two Hill-type lower limb muscles were attached to the model. The excitation-contraction dynamics of the contractile element, the tissues around the joints to limit the joint range of motion, as well as the foot-ground interaction were implemented. Simulations were initiated from an identical standing posture for both motions. Optimal pattern of the activation input signal was searched through numerical optimization. For the horizontal jumping, the goal was to maximize the horizontal distance traveled by the body's center of mass. For the vertical jumping, the goal was to maximize the height reached by the body's center of mass. Results As a result, it was found that the hip joint was utilized more vigorously in the horizontal jumping than in the vertical jumping. The muscles that have a function of joint flexion such as the m. iliopsoas, m. rectus femoris and m. tibialis anterior were activated to a greater level during the countermovement in the horizontal jumping with an effect of moving the body's center of mass in the forward direction. Muscular work was transferred to the mechanical energy of the body's center of mass more effectively in the horizontal jump, which resulted in a greater energy gain of the body's center of mass throughout the motion. Conclusion These differences in the optimal coordination strategy seem to be caused from the requirement that the body's center of mass needs to be located above the feet in a vertical jumping, whereas this requirement is not so strict in a horizontal jumping. PMID:17543118

Development and modeling of self-deployable structures

NASA Astrophysics Data System (ADS)

Neogi, Depankar

Deployable space structures are prefabricated structures which can be transformed from a closed, compact configuration to a predetermined expanded form in which they are stable and can bear loads. The present research effort investigates a new family of deployable structures, called the Self-Deployable Structures (SDS). Unlike other deployable structures, which have rigid members, the SDS members are flexible while the connecting joints are rigid. The joints store the predefined geometry of the deployed structure in the collapsed state. The SDS is stress-free in both deployed and collapsed configurations and results in a self-standing structure which acquires its structural properties after a chemical reaction. Reliability of deployment is one of the most important features of the SDS, since it does not rely on mechanisms that can lock during deployment. The unit building block of these structures is the self-deployable structural element (SDSE). Several SDSE members can be linked to generate a complex building block such as a triangular or a tetrahedral structure. Different SDSE and SDS concepts are investigated in the research work, and the performance of SDS's are experimentally and theoretically explored. Triangular and tetrahedral prototype SDS have been developed and presented. Theoretical efforts include modeling the behavior of 2-dimensional SDSs. Using this design tool, engineers can study the effects of different packing configurations and deployment sequence; and perform optimization on the collapsed state of a structure with different external constraints. The model also predicts if any lockup or entanglement occurs during deployment.

Childhood obesity case statement.

PubMed

Esposito, Paul W; Caskey, Paul; Heaton, Lisa E; Otsuka, Norman

2013-04-01

The goal of this publication is to raise awareness of the impact of childhood obesity on the musculoskeletal health of children and its potential long-term implications. Relevant articles dealing with musculoskeletal disorders either caused by or worsened by childhood obesity were reviewed through a Pub Med search. Efforts to recognize and combat the childhood obesity epidemic were also identified through Internet search engines. This case statement was then reviewed by the members of the pediatric specialty group of the US Bone and Joint Initiative, which represents an extensive number of organizations dealing with musculoskeletal health. Multiple musculoskeletal disorders are clearly caused by or worsened by childhood obesity. The review of the literature clearly demonstrates the increased frequency and severity of many childhood musculoskeletal disorders. Concerns about the long-term implications of these childhood onset disorders such as pain and degenerative changes into adulthood are clearly recognized by all the member organizations of the US Bone and Joint Initiative. It is imperative to recognize the long-term implications of musculoskeletal disorders caused by or worsened by childhood obesity. It is also important to recognize that the ability to exercise comfortably is a key factor to developing a healthy lifestyle and maintaining a healthy body weight. Efforts to develop reasonable and acceptable programs to increase physical activity by all facets of society should be supported. Further research into the long-term implications of childhood musculoskeletal disorders related to childhood obesity is necessary. Copyright © 2013 Elsevier Inc. All rights reserved.

Urologic cancer in Japan: role of Japan at the frontier of issues in Asia.

PubMed

Akaza, Hideyuki

2016-01-01

The characteristics of urological cancer in Japan can be summarized in the following points. (i) As the onset of this type of cancer is typically seen in elderly patients, it is becoming a major social issue in Japan that has already become an aging society. (ii) Many diverse treatment methods are available and a response is required that prioritizes quality of life. (iii) Although vigorous research and development efforts into new drugs are being carried out on a global level, resulting in beneficial medical agents becoming more readily available, unless concepts relating to cost vs. effectiveness are further developed and there is a real risk that medical systems and structures in their current form will become unsustainable. (iv) Although at the current point there are no original large-scale clinical trials being conducted in Asia, Japan has a wealth of experience of participating in many international joint clinical trials and it is therefore an urgent and pressing challenge to organize joint clinical trials in Asia and amass a body of knowledge that is unique to Asia. In view of this current situation and given Japan's position at the frontier of issues, it is important for Japan to take the initiative in Asia in cooperating with other Asian nations in efforts to resolve and overcome various challenges. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

First-principles data-driven discovery of transition metal oxides for artificial photosynthesis

NASA Astrophysics Data System (ADS)

Yan, Qimin

We develop a first-principles data-driven approach for rapid identification of transition metal oxide (TMO) light absorbers and photocatalysts for artificial photosynthesis using the Materials Project. Initially focusing on Cr, V, and Mn-based ternary TMOs in the database, we design a broadly-applicable multiple-layer screening workflow automating density functional theory (DFT) and hybrid functional calculations of bulk and surface electronic and magnetic structures. We further assess the electrochemical stability of TMOs in aqueous environments from computed Pourbaix diagrams. Several promising earth-abundant low band-gap TMO compounds with desirable band edge energies and electrochemical stability are identified by our computational efforts and then synergistically evaluated using high-throughput synthesis and photoelectrochemical screening techniques by our experimental collaborators at Caltech. Our joint theory-experiment effort has successfully identified new earth-abundant copper and manganese vanadate complex oxides that meet highly demanding requirements for photoanodes, substantially expanding the known space of such materials. By integrating theory and experiment, we validate our approach and develop important new insights into structure-property relationships for TMOs for oxygen evolution photocatalysts, paving the way for use of first-principles data-driven techniques in future applications. This work is supported by the Materials Project Predictive Modeling Center and the Joint Center for Artificial Photosynthesis through the U.S. Department of Energy, Office of Basic Energy Sciences, Materials Sciences and Engineering Division, under Contract No. DE-AC02-05CH11231. Computational resources also provided by the Department of Energy through the National Energy Supercomputing Center.

Autonomous power management and distribution

NASA Technical Reports Server (NTRS)

Dolce, Jim; Kish, Jim

1990-01-01

The goal of the Autonomous Power System program is to develop and apply intelligent problem solving and control to the Space Station Freedom's electric power testbed being developed at NASA's Lewis Research Center. Objectives are to establish artificial intelligence technology paths, craft knowledge-based tools and products for power systems, and integrate knowledge-based and conventional controllers. This program represents a joint effort between the Space Station and Office of Aeronautics and Space Technology to develop and demonstrate space electric power automation technology capable of: (1) detection and classification of system operating status, (2) diagnosis of failure causes, and (3) cooperative problem solving for power scheduling and failure recovery. Program details, status, and plans will be presented.

Efficient System Design and Sustainable Finance for China's Village Electrification Program: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, S.; Yin, H.; Kline, D. M.

2006-08-01

This paper describes a joint effort of the Institute for Electrical Engineering of the Chinese Academy of Sciences (IEE), and the U.S. National Renewable Energy Laboratory (NREL) to support China's rural electrification program. This project developed a design tool that provides guidelines both for off-grid renewable energy system designs and for cost-based tariff and finance schemes to support them. This tool was developed to capitalize on lessons learned from the Township Electrification Program that preceded the Village Electrification Program. We describe the methods used to develop the analysis, some indicative results, and the planned use of the tool in themore » Village Electrification Program.« less

State of global pediatric neurosurgery outreach: survey by the International Education Subcommittee.

PubMed

Davis, Matthew C; Rocque, Brandon G; Singhal, Ash; Ridder, Thomas; Pattisapu, Jogi V; Johnston, James M

2017-08-01

OBJECTIVE Neurosurgical services are increasingly recognized as essential components of surgical care worldwide. The degree of interest among neurosurgeons regarding international work, and the barriers to involvement in global neurosurgical outreach, are largely unexplored. The authors distributed a survey to members of the American Association of Neurological Surgeons/Congress of Neurological Surgeons (AANS/CNS) Joint Section on Pediatric Neurosurgery to assess the state of global outreach among its members and to identify barriers to involvement. METHODS An internet-based questionnaire was developed by the International Education Subcommittee of the AANS/CNS Joint Section on Pediatric Neurosurgery and distributed to pediatric neurosurgeons via the AANS/CNS Joint Section email contact list. Participants were surveyed on their involvement in global neurosurgical outreach, geographic location, nature of the participation, and barriers to further involvement. RESULTS A 35.3% response rate was obtained, with 116 respondents completing the survey. Sixty-one percent have performed or taught neurosurgery in a developing country, and 49% travel at least annually. Africa was the most common region (54%), followed by South America (30%), through 29 separate organizing entities. Hydrocephalus was the most commonly treated condition (88%), followed by spinal dysraphism (74%), and tumor (68%). Most respondents obtained follow-up through communications from local surgeons (77%). Seventy-one percent believed the international experience improved their practice, and 74% were very or extremely interested in working elsewhere. Interference with current practice (61%), cost (44%), and difficulty identifying international partners (43%) were the most commonly cited barriers to participation. CONCLUSIONS Any coordinated effort to expand global neurosurgical capacity begins with appreciation for the current state of outreach efforts. Increasing participation in global outreach will require addressing both real and perceived barriers to involvement. Creation and curation of a centralized online database of ongoing projects to facilitate coordination and involvement may be beneficial.

How Can We Best Achieve Contracting Unity of Effort in the CENTCOM Area of Responsibility?

DTIC Science & Technology

2013-12-01

3  2.  Literature Review ................................................................................3  3.  Interview Design and...2010, JCC-I/A was re- designated as the Central Command Joint Theater Support Contracting Command (C-JTSCC). Although the military has used...provision of integrated contracted support and management of contractor personnel providing that support to the joint force in a designated operational

A Systematic Approach to the Study of Accelerated weathering of Building Joint Sealants

Treesearch

Christopher C. White; Donald L. Hunston; Kar Tean Tan; James J. Filliben; Adam L. Pintar; Greg Schueneman

2012-01-01

An accurate service life prediction model is needed for building joint sealants in order to greatly reduce the time to market of a new product and reduce the risk of introducing a poorly performing product into the marketplace. A stepping stone to the success of this effort is the precise control of environmental variables in a laboratory accelerated test apparatus in...

Text Mining the Biomedical Literature

DTIC Science & Technology

2007-11-05

activities, and repeating past mistakes, or 3) agencies not participating in joint efforts that would fully exploit each agency’s strengths...research and joint projects (multi- department, multi-agency, multi-national, and government-industry) appropriate? • Is the balance among single...overall database taxonomy, i.e., are there any concepts missing from any of the databases, and even if not, do all the concepts bear the same

Experimental Investigation of Solder Joint Defect Formation and Mitigation in Reduced-Gravity Environments

NASA Technical Reports Server (NTRS)

Watson, J. Kevin; Struk, Peter M.; Pettegrew, RIchard D.; Downs, Robert S.

2006-01-01

This paper documents a research effort on reduced gravity soldering of plated through hole joints which was conducted jointly by the National Center for Space Exploration Research, NASA Glenn Research Center, and NASA Johnson Space Center. Significant increases in joint porosity and changes in external geometry were observed in joints produced in reduced gravity as compared to normal gravity. Multiple techniques for mitigating the observed increase in porosity were tried, including several combinations of flux and solder application techniques, and demoisturizing the circuit board prior to soldering. Results were consistent with the hypothesis that the source of the porosity is a combination of both trapped moisture in the circuit board itself, as well as vaporized flux that is trapped in the molten solder. Other topics investigated include correlation of visual inspection results with joint porosity, pore size measurements, limited pressure effects (0.08 MPa - 0.1 MPa) on the size and number of pores, and joint cooling rate.

Structural analysis of a bolted joint concept for the space shuttle's solid rocket motor casing

NASA Technical Reports Server (NTRS)

Lindell, Michael C.; Stalnaker, Winifred A.

1987-01-01

The Space Shuttle Challenger accident is thought to have been caused by the failure of one of the tang-clevis joints joining together the casing segments of the Solid Rocket Motors (SRM). Excessive displacement between the tang and clevis, possibly unseating the O-ring seals, may have initiated the resulting accident. An effort was made at NASA Langley Research Center to design an alternative concept for mating the casing segments. A bolted flange joint concept was designed and analyzed to determine if the concept would effectively maintain a seal while minimizing joint weight and controlling stress levels. It is shown that under the loading conditions analyzed the seal area of the joint remains seated. The only potential stress problem is a stress concentration in the flange at the edge of the bolt hole, which is highly localized. While heavier than the existing joint, this concept does have some advantages making the bolted joint an attractive alternative.

Goddard Technology Efforts to Improve Space Borne Laser Reliability

NASA Technical Reports Server (NTRS)

Heaps, William S.

2006-01-01

In an effort to reduce the risk, perceived and actual, of employing instruments containing space borne lasers NASA initiated the Laser Risk Reduction Program (LRRP) in 2001. This program managed jointly by NASA Langley and NASA Goddard and employing lasers researchers from government, university and industrial labs is nearing the conclusion of its planned 5 year duration. This paper will describe some of the efforts and results obtained by the Goddard half of the program.

Oil Recovery Enhancement from Fractured, Low Permeability Reservoirs. [Carbonated Water

DOE R&D Accomplishments Database

Poston, S. W.

1991-01-01

The results of the investigative efforts for this jointly funded DOE-State of Texas research project achieved during the 1990-1991 year may be summarized as follows: Geological Characterization - Detailed maps of the development and hierarchical nature the fracture system exhibited by Austin Chalk outcrops were prepared. The results of these efforts were directly applied to the development of production decline type curves applicable to a dual-fracture-matrix flow system. Analysis of production records obtained from Austin Chalk operators illustrated the utility of these type curves to determine relative fracture/matrix contributions and extent. Well-log response in Austin Chalk wells has been shown to be a reliable indicator of organic maturity. Shear-wave splitting concepts were used to estimate fracture orientations from Vertical Seismic Profile, VSP data. Several programs were written to facilitate analysis of the data. The results of these efforts indicated fractures could be detected with VSP seismic methods. Development of the EOR Imbibition Process - Laboratory displacement as well as Magnetic Resonance Imaging, MRI and Computed Tomography, CT imaging studies have shown the carbonated water-imbibition displacement process significantly accelerates and increases recovery from oil saturated, low permeability rocks. Field Tests - Two operators amenable to conducting a carbonated water flood test on an Austin Chalk well have been identified. Feasibility studies are presently underway.

The relation between residual stress, interfacial structure and the joint property in the SiO2f/SiO2-Nb joints.

PubMed

Ma, Qiang; Li, Zhuo Ran; Yang, Lai Shan; Lin, Jing Huang; Ba, Jin; Wang, Ze Yu; Qi, Jun Lei; Feng, Ji Cai

2017-06-23

In order to achieve a high-quality joint between SiO 2f /SiO 2 and metals, it is necessary to address the poor wettability of SiO 2f /SiO 2 and the high residual stress in SiO 2f /SiO 2 -Nb joint. Here, we simultaneously realize good wettability and low residual stress in SiO 2f /SiO 2 -Nb joint by combined method of HF etching treatment and Finite Element Analysis (FEA). After etching treatment, the wettability of E-SiO 2f /SiO 2 was improved, and the residual stress in the joint was decreased. In order to better control the quality of joints, efforts were made to understand the relationship between surface structure of E-SiO 2f /SiO 2 and residual stress in joint using FEA. Based on the direction of FEA results, a relationship between residual stress, surface structure and joint property in the brazed joints were investigated by experiments. As well the FEA and the brazing test results both realized the high-quality joint of E-SiO 2f /SiO 2 -Nb and the shear strength of the joint reached 61.9 MPa.

Travels with Chairman of the Joint Chiefs of Staff, Marine General Peter

Science.gov Websites

that time. Story Counter-drug Efforts May Aid Afghanistan BOGOTA, Colombia, Jan. 20, 2007 – The long experience in its counter-drug effort to help the Afghan government fight a similar battle. " has working the counter-drug (issue)," Marine Gen. Peter Pace said. "It's been a very

Investigating the primary stability of the transversal support tibial plateau concept to retain both cruciate ligaments during total knee arthroplasty.

PubMed

Nowakowski, Andrej M; Stangel, Melanie; Grupp, Thomas M; Valderrabano, Victor

2012-09-27

The important roles of the anterior cruciate ligament regarding knee stability, physiologic kinematics, and proprioception are unquestioned. Thus, various efforts have been made to retain the ACL during total knee arthroplasty (TKA). Neither of the existing solutions to this problem, i.e. bicruciate retaining prostheses and implantation of two unicondylar prostheses, has been successful because of concept-specific problems as well as general difficulties with implant fixation. The new transversal support tibial plateau concept is a prosthesis of two individual joint surfaces reinforced beneath the articular line by joint surface supports and buttressed by a single transversal support. This configuration, which enables retention of both cruciate ligaments, should provide good bone fixation and ensure long-term alignment of the individual joint surfaces. In the current study, four prototypes based on this novel concept were developed and the resulting primary stability was analyzed using adapted load testing. The test set-up, with the model-loading of specially prepared Sawbones® and a sinusoidal oscillating load transmission with 25 000 cycles over 10 increasing load levels, achieved subsidence, which enabled comparison of the four different model variants regarding primary stability in view of bone anchoring. The model variant (TSmobile) that allowed transverse glide of the joint surface supports along the transversal support revealed the largest subsidence. A rigid attachment of the joint surface supports of the transversal support tibial plateau thus appears to offer increased primary stability regarding bone anchoring.

Inequity responses of monkeys modified by effort.

PubMed

van Wolkenten, Megan; Brosnan, Sarah F; de Waal, Frans B M

2007-11-20

Without joint benefits, joint actions could never have evolved. Cooperative animals need to monitor closely how large a share they receive relative to their investment toward collective goals. This work documents the sensitivity to reward division in brown, or tufted, capuchin monkeys (Cebus apella). In addition to confirming previous results with a larger subject pool, this work rules out several alternative explanations and adds data on effort sensitivity. Thirteen adult monkeys exchanged tokens for rewards, showing negative reactions to receiving a less-favored reward than their partner. Because their negative reaction could not be attributed to the mere visibility of better rewards (greed hypothesis) nor to having received such rewards in the immediate past (frustration hypothesis), it must have been caused by seeing their partner obtain the better reward. Effort had a major effect in that by far the lowest level of performance in the entire study occurred in subjects required to expend a large effort while at the same time seeing their partner receive a better reward. It is unclear whether this effort-effect was based on comparisons with the partner, but it added significantly to the intensity of the inequity response. These effects are as expected if the inequity response evolved in the context of cooperative survival strategies.

Fluid dynamic mechanisms and interactions within separated flows

NASA Astrophysics Data System (ADS)

Dutton, J. C.; Addy, A. L.

1990-02-01

The significant results of a joint research effort investigating the fundamental fluid dynamic mechanisms and interactions within high-speed separated flows are presented in detail. The results have obtained through analytical and numerical approaches, but with primary emphasis on experimental investigations of missile and projectile base flow-related configurations. The objectives of the research program focus on understanding the component mechanisms and interactions which establish and maintain high-speed separated flow regions. The analytical and numerical efforts have centered on unsteady plume-wall interactions in rocket launch tubes and on predictions of the effects of base bleed on transonic and supersonic base flowfields. The experimental efforts have considered the development and use of a state-of-the-art two component laser Doppler velocimeter (LDV) system for experiments with planar, two-dimensional, small-scale models in supersonic flows. The LDV experiments have yielded high quality, well documented mean and turbulence velocity data for a variety of high-speed separated flows including initial shear layer development, recompression/reattachment processes for two supersonic shear layers, oblique shock wave/turbulent boundary layer interactions in a compression corner, and two-stream, supersonic, near-wake flow behind a finite-thickness base.

Angular Deformities of the Lower Limb in Children

PubMed Central

Espandar, Ramin; Mortazavi, Seyed Mohammad-Javad; Baghdadi, Taghi

2010-01-01

Angular deformities of the lower limbs are common during childhood. In most cases this represents a variation in the normal growth pattern and is an entirely benign condition. Presence of symmetrical deformities and absence of symptoms, joint stiffness, systemic disorders or syndromes indicates a benign condition with excellent long-term outcome. In contrast, deformities which are asymmetrical and associated with pain, joint stiffness, systemic disorders or syndromes may indicate a serious underlying cause and require treatment. Little is known about the relationship between sport participation and body adaptations during growth. Intense soccer participation increases the degree of genu varum in males from the age of 16. Since, according to some investigations, genu varum predisposes individuals to more injuries, efforts to reduce the development of genu varum in soccer players are warranted. In this article major topics of angular deformities of the knees in pediatric population are practically reviewed. PMID:22375192

An Engineering Model of Human Balance Control-Part I: Biomechanical Model.

PubMed

Barton, Joseph E; Roy, Anindo; Sorkin, John D; Rogers, Mark W; Macko, Richard

2016-01-01

We developed a balance measurement tool (the balanced reach test (BRT)) to assess standing balance while reaching and pointing to a target moving in three-dimensional space according to a sum-of-sines function. We also developed a three-dimensional, 13-segment biomechanical model to analyze performance in this task. Using kinematic and ground reaction force (GRF) data from the BRT, we performed an inverse dynamics analysis to compute the forces and torques applied at each of the joints during the course of a 90 s test. We also performed spectral analyses of each joint's force activations. We found that the joints act in a different but highly coordinated manner to accomplish the tracking task-with individual joints responding congruently to different portions of the target disk's frequency spectrum. The test and the model also identified clear differences between a young healthy subject (YHS), an older high fall risk (HFR) subject before participating in a balance training intervention; and in the older subject's performance after training (which improved to the point that his performance approached that of the young subject). This is the first phase of an effort to model the balance control system with sufficient physiological detail and complexity to accurately simulate the multisegmental control of balance during functional reach across the spectra of aging, medical, and neurological conditions that affect performance. Such a model would provide insight into the function and interaction of the biomechanical and neurophysiological elements making up this system; and system adaptations to changes in these elements' performance and capabilities.

An Engineering Model of Human Balance Control—Part I: Biomechanical Model

PubMed Central

Barton, Joseph E.; Roy, Anindo; Sorkin, John D.; Rogers, Mark W.; Macko, Richard

2016-01-01

We developed a balance measurement tool (the balanced reach test (BRT)) to assess standing balance while reaching and pointing to a target moving in three-dimensional space according to a sum-of-sines function. We also developed a three-dimensional, 13-segment biomechanical model to analyze performance in this task. Using kinematic and ground reaction force (GRF) data from the BRT, we performed an inverse dynamics analysis to compute the forces and torques applied at each of the joints during the course of a 90 s test. We also performed spectral analyses of each joint's force activations. We found that the joints act in a different but highly coordinated manner to accomplish the tracking task—with individual joints responding congruently to different portions of the target disk's frequency spectrum. The test and the model also identified clear differences between a young healthy subject (YHS), an older high fall risk (HFR) subject before participating in a balance training intervention; and in the older subject's performance after training (which improved to the point that his performance approached that of the young subject). This is the first phase of an effort to model the balance control system with sufficient physiological detail and complexity to accurately simulate the multisegmental control of balance during functional reach across the spectra of aging, medical, and neurological conditions that affect performance. Such a model would provide insight into the function and interaction of the biomechanical and neurophysiological elements making up this system; and system adaptations to changes in these elements' performance and capabilities. PMID:26328608

Multidisciplinary Design Technology Development: A Comparative Investigation of Integrated Aerospace Vehicle Design Tools

NASA Technical Reports Server (NTRS)

Renaud, John E.; Batill, Stephen M.; Brockman, Jay B.

1998-01-01

This research effort is a joint program between the Departments of Aerospace and Mechanical Engineering and the Computer Science and Engineering Department at the University of Notre Dame. Three Principal Investigators; Drs. Renaud, Brockman and Batill directed this effort. During the four and a half year grant period, six Aerospace and Mechanical Engineering Ph.D. students and one Masters student received full or partial support, while four Computer Science and Engineering Ph.D. students and one Masters student were supported. During each of the summers up to four undergraduate students were involved in related research activities. The purpose of the project was to develop a framework and systematic methodology to facilitate the application of Multidisciplinary Design Optimization (N4DO) to a diverse class of system design problems. For all practical aerospace systems, the design of a systems is a complex sequence of events which integrates the activities of a variety of discipline "experts" and their associated "tools". The development, archiving and exchange of information between these individual experts is central to the design task and it is this information which provides the basis for these experts to make coordinated design decisions (i.e., compromises and trade-offs) - resulting in the final product design. Grant efforts focused on developing and evaluating frameworks for effective design coordination within a MDO environment. Central to these research efforts was the concept that the individual discipline "expert", using the most appropriate "tools" available and the most complete description of the system should be empowered to have the greatest impact on the design decisions and final design. This means that the overall process must be highly interactive and efficiently conducted if the resulting design is to be developed in a manner consistent with cost and time requirements. The methods developed as part of this research effort include; extensions to a sensitivity based Concurrent Subspace Optimization (CSSO) MDO algorithm; the development of a neural network response surface based CSSO-MDO algorithm; and the integration of distributed computing and process scheduling into the MDO environment. This report overviews research efforts in each of these focus. A complete bibliography of research produced with support of this grant is attached.

The selection of the American-Polish joint venture projects for the Krakow program and results of the efforts to date

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gyorke, D.F.; Butcher, T.A.

1995-12-31

To implement the Krakow Clean Fossil Fuels and Energy Efficiency Program, eight U.S. firms were selected by the U.S. Department of Energy to market their technologies to reduce pollution from low emission sources in Krakow. The eight U.S. firms were selected by a competitive solicitation that required the proposing firms to themselves provide funding to match or exceed the funding provided by the Program. These U.S. firms and their Polish partner companies have begun sales and cooperative work efforts in Krakow, and some have already made initial equipment installations with measurable performance improvements. Following their efforts as part of themore » Program, these U.S.-Polish joint ventures will market their technologies and achieve the associated environmental benefits elsewhere in Poland and Eastern and Central Europe. As part of the Krakow Program a spreadsheet model was developed to compare technological options for supplying heat to the city by calculation and comparing the heating costs and associated emissions reduction for each option. Comparison of options is made on the basis of the user cost-per-metric ton of equivalent emissions reduction. For all options considered in the Krakow Program, this cost parameter has ranged from -$1469 (best) to $2650 (worst). The costs for technologies associated with the eight projects in the Krakow Program are at the lower end of this range placing these technologies among the most cost effective solutions to the pollution problems from the low emission sources.« less

Hyper-X Engine Design and Ground Test Program

NASA Technical Reports Server (NTRS)

Voland, R. T.; Rock, K. E.; Huebner, L. D.; Witte, D. W.; Fischer, K. E.; McClinton, C. R.

1998-01-01

The Hyper-X Program, NASA's focused hypersonic technology program jointly run by NASA Langley and Dryden, is designed to move hypersonic, air-breathing vehicle technology from the laboratory environment to the flight environment, the last stage preceding prototype development. The Hyper-X research vehicle will provide the first ever opportunity to obtain data on an airframe integrated supersonic combustion ramjet propulsion system in flight, providing the first flight validation of wind tunnel, numerical and analytical methods used for design of these vehicles. A substantial portion of the integrated vehicle/engine flowpath development, engine systems verification and validation and flight test risk reduction efforts are experimentally based, including vehicle aeropropulsive force and moment database generation for flight control law development, and integrated vehicle/engine performance validation. The Mach 7 engine flowpath development tests have been completed, and effort is now shifting to engine controls, systems and performance verification and validation tests, as well as, additional flight test risk reduction tests. The engine wind tunnel tests required for these efforts range from tests of partial width engines in both small and large scramjet test facilities, to tests of the full flight engine on a vehicle simulator and tests of a complete flight vehicle in the Langley 8-Ft. High Temperature Tunnel. These tests will begin in the summer of 1998 and continue through 1999. The first flight test is planned for early 2000.

Building a Communication, Education, an Outreach Program for the ShakeAlert National Earthquake Early Warning Program

NASA Astrophysics Data System (ADS)

DeGroot, R. M.; Strauss, J. A.; Given, D. D.; Cochran, E. S.; Burkett, E. R.; Long, K.

2016-12-01

Earthquake Early Warning (EEW) systems can provide as much as tens of seconds of warning to people and automated systems before strong shaking arrives. The United States Geological Survey (USGS) and its partners are developing an EEW system for the West Coast of the United States. To be an integral part of successful implementation, EEW engagement programs and materials must integrate with and leverage broader earthquake risk programs. New methods and products for dissemination must be multidisciplinary, cost effective, and consistent with existing hazards education efforts. Our presentation outlines how the USGS and its partners will approach this effort in the context of the EEW system through the work of a multistate and multiagency committee that participates in the design, implementation, and evaluation of a portfolio of programs and products. This committee, referred to as the ShakeAlert Joint Committee for Communication, Education, and Outreach (ShakeAlert CEO), is working to identify, develop, and cultivate partnerships with EEW stakeholders including Federal, State, academic partners, private companies, policy makers, and local organizations. Efforts include developing materials, methods for delivery, and reaching stakeholders with information on EEW, earthquake preparedness, and emergency protective actions. It is essential to develop standards to ensure information communicated via the EEW alerts is consistent across the public and private sector and achieving a common understanding of what actions users take when they receive an EEW warning. The USGS and the participating states and agencies acknowledge that the implementation of EEW is a collective effort requiring the participation of hundreds of stakeholders committed to ensuring public accessibility.

A method to accurately estimate the muscular torques of human wearing exoskeletons by torque sensors.

PubMed

Hwang, Beomsoo; Jeon, Doyoung

2015-04-09

In exoskeletal robots, the quantification of the user's muscular effort is important to recognize the user's motion intentions and evaluate motor abilities. In this paper, we attempt to estimate users' muscular efforts accurately using joint torque sensor which contains the measurements of dynamic effect of human body such as the inertial, Coriolis, and gravitational torques as well as torque by active muscular effort. It is important to extract the dynamic effects of the user's limb accurately from the measured torque. The user's limb dynamics are formulated and a convenient method of identifying user-specific parameters is suggested for estimating the user's muscular torque in robotic exoskeletons. Experiments were carried out on a wheelchair-integrated lower limb exoskeleton, EXOwheel, which was equipped with torque sensors in the hip and knee joints. The proposed methods were evaluated by 10 healthy participants during body weight-supported gait training. The experimental results show that the torque sensors are to estimate the muscular torque accurately in cases of relaxed and activated muscle conditions.

WFIRST Project Science Activities

NASA Technical Reports Server (NTRS)

Gehrels, Neil

2012-01-01

The WFIRST Project is a joint effort between GSFC and JPL. The project scientists and engineers are working with the community Science Definition Team to define the requirements and initial design of the mission. The objective is to design an observatory that meets the WFIRST science goals of the Astr02010 Decadal Survey for minimum cost. This talk will be a report of recent project activities including requirements flowdown, detector array development, science simulations, mission costing and science outreach. Details of the interim mission design relevant to scientific capabilities will be presented.

Terminal-area STOL operating systems experiments program

NASA Technical Reports Server (NTRS)

Smith, D. W.; Watson, D.; Christensen, J. V.

1973-01-01

Information which will aid in the choice by the U.S. Government and industry of system concepts, design criteria, operating procedures for STOL aircraft and STOL ports, STOL landing guidance systems, air traffic control systems, and airborne avionics and flight control systems. Ames has developed a terminal-area STOL operating systems experiments program which is a part of the joint DOT/NASA effort is discussed. The Ames operating systems experiments program, its objectives, the program approach, the program schedule, typical experiments, the research facilities to be used, and the program status are described.

The Human-Electronic Crew: The Right Stuff? Proceedings of the 4th Joint GAF/RAF/USAF Workshop on Human-Computer Teamwork

DTIC Science & Technology

1999-12-01

the technological and psychological issues but to try and bring to bear some of my operational experience. It is this kind of input that I believe... psychological stress. This is more evident in combat missions, during critical phases of flight, and may become more prevalent with ongoing efforts...Defence’ at St Hugh’s, Oxford Mar 1995. 2 MERRIMAN,S. edit . "Applications of System Ergonomics to Weapon System Development", NATO-DRG Panel 8 Workshop

Remote sensing in Michigan for land resource management

NASA Technical Reports Server (NTRS)

Sattinger, I. J.

1972-01-01

This project to demonstrate the application of earth resource survey technology to current problems in Michigan was undertaken jointly by the Environmental Research Institute of Michigan and Michigan State University. Remote sensing techniques were employed to advantage in providing management information for the Pointe Mouillee State Game Area and preparing an impact assessment in advance of the projected construction of the M-14 freeway from Ann Arbor to Plymouth, Michigan. The project also assisted the state government in its current effort to develop and implement a state-wide land management plan.

Design of joint source/channel coders

NASA Technical Reports Server (NTRS)

1991-01-01

The need to transmit large amounts of data over a band limited channel has led to the development of various data compression schemes. Many of these schemes function by attempting to remove redundancy from the data stream. An unwanted side effect of this approach is to make the information transfer process more vulnerable to channel noise. Efforts at protecting against errors involve the reinsertion of redundancy and an increase in bandwidth requirements. The papers presented within this document attempt to deal with these problems from a number of different approaches.

The 1990-1991 project summaries

NASA Technical Reports Server (NTRS)

1991-01-01

Georgia Tech's School of Textile & Fiber Engineering and School of Mechanical Engineering participated in four cooperative design efforts this year. One group designed a thermal shield for a lunar telescope. The second group designed a selenotextile habitat shielding structure. The third group designed a pneumatically assisted elbow joint for the NASA zero-prebreathe suit (ZPS). The final group designed an electromechanical system to power an astronaut's finger joints. Summaries of these projects are presented.

The 1990-1991 project summaries

NASA Astrophysics Data System (ADS)

Georgia Tech's School of Textile & Fiber Engineering and School of Mechanical Engineering participated in four cooperative design efforts this year. One group designed a thermal shield for a lunar telescope. The second group designed a selenotextile habitat shielding structure. The third group designed a pneumatically assisted elbow joint for the NASA zero-prebreathe suit (ZPS). The final group designed an electromechanical system to power an astronaut's finger joints. Summaries of these projects are presented.

Ankle moment generation and maximum-effort curved sprinting performance.

PubMed

Luo, Geng; Stefanyshyn, Darren

2012-11-15

Turning at high speed along acute curves is crucial for athletic performance. One determinant of curved sprinting speed is the ground reaction force that can be created by the supporting limb; the moment generated at the ankle joint may influence such force generation. Body lean associated with curved sprints positions the ankle joints in extreme in-/eversion, and may hinder the ankle moment generation. To examine the influence of ankle moment generation on curved sprinting performance, 17 male subjects performed maximum-effort curved sprints in footwear with and without a wedge. The wedged footwear was constructed with the intention to align the ankle joints closer to their neutral frontal-plane configuration during counter-clockwise curved sprints so greater joint moments might be generated. We found, with the wedged footwear, the average eversion angle of the inside leg ankle was reduced, and the plantarflexion moment generation increased significantly. Meanwhile, the knee extension moment remained unchanged. With the wedged footwear, stance-average centripetal ground reaction force increased significantly while no difference in the vertical ground reaction force was detected. The subjects created a greater centripetal ground reaction impulse in the wedged footwear despite a shortened stance phase when compared to the control. Stance-average curved sprinting speed improved by 4.3% with the wedged footwear. The changes in ankle moment and curved sprinting speed observed in the current study supports the notion that the moment generation at the ankle joint may be a performance constraint for curved sprinting. Copyright © 2012 Elsevier Ltd. All rights reserved.

Assessing country-level efforts to link research to action.

PubMed Central

Lavis, John N.; Lomas, Jonathan; Hamid, Maimunah; Sewankambo, Nelson K.

2006-01-01

We developed a framework for assessing country-level efforts to link research to action. The framework has four elements. The first element assesses the general climate (how those who fund research, universities, researchers and users of research support or place value on efforts to link research to action). The second element addresses the production of research (how priority setting ensures that users' needs are identified and how scoping reviews, systematic reviews and single studies are undertaken to address these needs). The third element addresses the mix of four clusters of activities used to link research to action. These include push efforts (how strategies are used to support action based on the messages arising from research), efforts to facilitate "user pull" (how "one-stop shopping" is provided for optimally packaged high-quality reviews either alone or as part of a national electronic library for health, how these reviews are profiled during "teachable moments" such as intense media coverage, and how rapid-response units meet users' needs for the best research), "user pull" efforts undertaken by those who use research (how users assess their capacity to use research and how structures and processes are changed to support the use of research) and exchange efforts (how meaningful partnerships between researchers and users help them to jointly ask and answer relevant questions). The fourth element addresses approaches to evaluation (how support is provided for rigorous evaluations of efforts to link research to action). PMID:16917649

Center of excellence for small robots

NASA Astrophysics Data System (ADS)

Nguyen, Hoa G.; Carroll, Daniel M.; Laird, Robin T.; Everett, H. R.

2005-05-01

The mission of the Unmanned Systems Branch of SPAWAR Systems Center, San Diego (SSC San Diego) is to provide network-integrated robotic solutions for Command, Control, Communications, Computers, Intelligence, Surveillance, and Reconnaissance (C4ISR) applications, serving and partnering with industry, academia, and other government agencies. We believe the most important criterion for a successful acquisition program is producing a value-added end product that the warfighter needs, uses and appreciates. Through our accomplishments in the laboratory and field, SSC San Diego has been designated the Center of Excellence for Small Robots by the Office of the Secretary of Defense Joint Robotics Program. This paper covers the background, experience, and collaboration efforts by SSC San Diego to serve as the "Impedance-Matching Transformer" between the robotic user and technical communities. Special attention is given to our Unmanned Systems Technology Imperatives for Research, Development, Testing and Evaluation (RDT&E) of Small Robots. Active projects, past efforts, and architectures are provided as success stories for the Unmanned Systems Development Approach.

ORNL superconducting technology program for electric power systems

NASA Astrophysics Data System (ADS)

Hawsey, R. A.

1994-04-01

The Oak Ridge National Laboratory (ORNL) Superconducting Technology Program is conducted as part of a national effort by the US Department of Energy's Office of Energy Efficiency and Renewable Energy to develop the technology base needed by US industry for commercial development of electric power applications of high-temperature superconductivity. The two major elements of this program are conductor development and applications development. This document describes the major research and development activities for this program together with related accomplishments. The technical progress reported was summarized from information prepared for the FY 1993 Annual Program Review held July 28--29, 1993. This ORNL program is highly leveraged by the staff and other resources of US industry and universities. In fact, nearly three-fourths of the ORNL effort is devoted to industrial competitiveness projects with private companies. Interlaboratory teams are also in place on a number of industry-driven projects. Patent disclosures, working group meetings, staff exchanges, and joint publications and presentations ensure that there is technology transfer to US industry. Working together, the collaborative teams are making rapid progress in solving the scientific and technical issues necessary for the commercialization of long lengths of practical high-temperature superconductor wire and wire products.

Size effects in tin-based lead-free solder joints: Kinetics of bond formation and mechanical characteristics

NASA Astrophysics Data System (ADS)

Abdelhadi, Ousama Mohamed Omer

Continuous miniaturization of microelectronic interconnects demands smaller joints with comparable microstructural and structural sizes. As the size of joints become smaller, the volume of intermetallics (IMCs) becomes comparable with the joint size. As a result, the kinetics of bond formation changes and the types and thicknesses of IMC phases that form within the constrained region of the bond varies. This dissertation focuses on investigating combination effects of process parameters and size on kinetics of bond formation, resulting microstructure and the mechanical properties of joints that are formed under structurally constrained conditions. An experiment is designed where several process parameters such as time of bonding, temperature, and pressure, and bond thickness as structural chracteristic, are varied at multiple levels. The experiment is then implemented on the process. Scanning electron microscope (SEM) is then utilized to determine the bond thickness, IMC phases and their thicknesses, and morphology of the bonds. Electron backscatter diffraction (EBSD) is used to determine the grain size in different regions, including the bulk solder, and different IMC phases. Physics-based analytical models have been developed for growth kinetics of IMC compounds and are verified using the experimental results. Nanoindentation is used to determine the mechanical behavior of IMC phases in joints in different scales. Four-point bending notched multilayer specimen and four-point bending technique were used to determine fracture toughness of the bonds containing IMCs. Analytical modeling of peeling and shear stresses and fracture toughness in tri-layer four-point bend specimen containing intermetallic layer was developed and was verified and validated using finite element simulation and experimental results. The experiment is used in conjunction with the model to calculate and verify the fracture toughness of Cu6Sn5 IMC materials. As expected two different IMC phases, η-phase (Cu6Sn 5) and epsilon-phase (Cu3Sn), were found in almost all the cases regardless of the process parameters and size levels. The physics-based analytical model was successfully able to capture the governing mechanisms of IMC growth: chemical reaction controlled and diffusion-controlled. Examination of microstructures of solder joints of different sizes revealed the size of the solder joint has no effect on the type of IMCs formed during the process. Joint size, however, affected the thickness of IMC layers significantly. IMC layers formed in the solder joints of smaller sizes were found to be thicker than those in the solder joints of larger sizes. The growth rate constants and activation energies of Cu3Sn IMC layer were also reported and related to joint thickness. In an effort to optimize the EBSD imaging in the multi-layer configuration, an improved specimen preparation technique and optimum software parameters were determined. Nanoindentation results show that size effects play a major role on the mechanical properties of micro-scale solder joints. Smaller joints show higher Young's modulus, hardness, and yield strength and lower work hardening exponents comparing to thicker joints. To obtain the stress concentration factors in a multilayer specimen with IMC layer as bonding material, a four-point bending notched configuration was used. The analytical solutions developed for peeling and shear stresses in notched structure were used to evaluate the stresses at IMC interface layers. Results were in good agreement with the finite-element simulation. The values of interfacial stresses were utilized in obtaining fracture toughness of the IMC material. (Abstract shortened by UMI.)

Commercial Contributions to the Success of the HEDS Enterprise: A Working Model

NASA Technical Reports Server (NTRS)

Nall, Mark; Askew, Ray

2000-01-01

The future of NASA involves the exploration of space beyond the confines of orbit about the Earth. This includes robotic investigations and Human Exploration and Development of Space (HEDS). The HEDS Strategic Plan states: "HEDS will join with the private sector to stimulate opportunities for commercial development in space as a key to future settlement. Near-term efforts will emphasize joint pilot projects that provide clear benefit to Earth from the development of near-Earth space." In support of this endeavor, NASA has established the Commercial Development of Space as a prime goal and is exploring all the ways in which NASA might make contributions to this development. NASA has long supported the development of space for commercial use. In 1985 it formally established and provided funds to support a program which created a number of joint ventures between universities and industry for this purpose. These were known as Centers for the Commercial Development of Space (CCDS). In 1999 NASA established a broader policy on commercialization with the aim of encouraging near-term commercial investment in conjunction with the International Space Station. Joint pilot projects will be initiated to stimulate this near-term investment. The long-term development of commercial concepts utilizing space access continues through the activities of the Commercial Space Centers (CSC), a sub-set of the original CCDS group. These Centers primarily require access to space for the conduct of their work. The remainder of the initial Centers focus on the development of tools and infrastructure to support users of the space environment. It is in this arena that long term development for commercial use and infrastructure development will occur. This paper will provide a retrospective examination of the Commercial Centers, the variety of models employed, the lessons learned, and the progress to date. This review will provide the bases for how successful models can be employed to accelerate private investment in the development of the infrastructure necessary for the success of the HEDS enterprise.

Fisher research in the US Rocky Mountains: A critical overview

Treesearch

Michael Schwartz; J. Sauder

2013-01-01

In this talk we review the recent fisher research and monitoring efforts that have occurred throughout Idaho and Montana in past 2 decades. We begin this talk with a summary of the habitat relationship work that has examined fisher habitat use at multiple scales. These have largely been conducted using radio and satellite telemetry, although a new, joint effort to use...

Inequity-aversion and relative kindness intention jointly determine the expenditure of effort in project teams.

PubMed

Han, Jiaojie; Rapoport, Amnon; Zhao, Rui

2017-01-01

The literature on team cooperation has neglected the effects of relative kindness intention on cooperation, which we measure by comparing the kindness intentions of an agent to her group members to the kindness shown by other members to this same agent. We argue that the agent's emotional reaction to material payoff inequity is not constant, but rather affected by her relative kindness intention. Then, we apply the model to team projects with multiple partners and investigate how inequity-aversion and relative kindness intention jointly influence team cooperation. We first consider the case of homogeneous agents, where their marginal productivity levels and technical capacities are the same, and then consider the case of heterogeneous agents, where their marginal productivity levels and technical capacities are not the same. Our results show that inequity-aversion has no effect on effort expenditure in the former case, but does affect it in the latter case. The consideration of relative kindness intention may impact the agents' optimal cooperative effort expenditure when their technical capacities are different. In addition, it is beneficial for team cooperation, and might not only reduce the negative impact but also enhance the positive impact of inequity-aversion on the agents' effort expenditures.

Rotorcraft handling-qualities design criteria development

NASA Technical Reports Server (NTRS)

Aiken, Edwin W.; Lebacqz, J. Victor; Chen, Robert T. N.; Key, David L.

1988-01-01

Joint NASA/Army efforts at the Ames Research Center to develop rotorcraft handling-qualities design criteria began in earnest in 1975. Notable results were the UH-1H VSTOLAND variable stability helicopter, the VFA-2 camera-and-terrain-board simulator visual system, and the generic helicopter real-time mathematical model, ARMCOP. An initial series of handling-qualities studies was conducted to assess the effects of rotor design parameters, interaxis coupling, and various levels of stability and control augmentation. The ability to conduct in-flight handling-qualities research was enhanced by the development of the NASA/Army CH-47 variable-stability helicopter. Research programs conducted using this vehicle include vertical-response investigations, hover augmentation systems, and the effects of control-force characteristics. The handling-qualities data base was judged to be sufficient to allow an update of the military helicopter handling-qualities specification, MIL-H-8501. These efforts, including not only the in-house experimental work but also contracted research and collaborative programs performed under the auspices of various international agreements. The report concludes by reviewing the topics that are currently most in need of work, and the plans for addressing these topics.

High performance low cost interconnections for flip chip attachment with electrically conductive adhesive. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-05-01

This final report is a compilation of final reports from each of the groups participating in the program. The main three groups involved in this effort are the Thomas J. Watson Research Center of IBM Corporation in Yorktown Heights, New York, Assembly Process Design of IBM Corporation in Endicott, New York, and SMT Laboratory of Universal Instruments Corporation in Binghamton, New York. The group at the research center focused on the conductive adhesive materials development and characterization. The group in process development focused on processing of the Polymer-Metal-Solvent Paste (PMSP) to form conductive adhesive bumps, formation of the Polymer-Metal Compositemore » (PMC) on semiconductor devices and study of the bonding process to circuitized organic carriers, and the long term durability and reliability of joints formed using the process. The group at Universal Instruments focused on development of an equipment set and bonding parameters for the equipment to produce bond assembly tooling. Reports of each of these individual groups are presented here reviewing their technical efforts and achievements.« less

An innovative partnership for national environmental assessment

USGS Publications Warehouse

Shaw, D.M.; Field, D.W.; Holm, T.M.; Jennings, M.D.; Sturdevant, J.A.; Thelin, G.P.; Worthy, L.D.

1993-01-01

Four federal environmental programs: EMAP (USEPA), GAP (USFWS), C-CAP (NOAA), NAWQA (USGS) have formed a partnership with EROS Data Center (USGS) to facilitate the development of baseline land characteristics information for the conterminous U.S. Each of the respective programs brings to the group unique experience and expertise. Despite emphasis on different environmental issues, together we have identified common requirements for source satellite data, preprocessing, spectral clustering, ancillary data, data management and distribution. We are also developing a research agenda to support this initiative and future efforts of this partnership. The short-term goal of out effort is the joint acquisition and preprocessing of recent Landsat TM images for the conterminous U.S. To date, images have been identified for acquisition, and preliminary plans have been made for preprocessing. The long-term goal for this group is collaborative research and development of a flexible and functional land characteristics database for use by our programs and others. This partnership demonstrates that national environmental programs within multiple government agencies can work effectively together to achieve common goals and reduce overall cost.

Aerospace Technology Innovation. Volume 10

NASA Technical Reports Server (NTRS)

Turner, Janelle (Editor); Cousins, Liz (Editor); Bennett, Evonne (Editor); Vendette, Joel (Editor); West, Kenyon (Editor)

2002-01-01

Whether finding new applications for existing NASA technologies or developing unique marketing strategies to demonstrate them, NASA's offices are committed to identifying unique partnering opportunities. Through their efforts NASA leverages resources through joint research and development, and gains new insight into the core areas relevant to all NASA field centers. One of the most satisfying aspects of my job comes when I learn of a mission-driven technology that can be spun-off to touch the lives of everyday people. NASA's New Partnerships in Medical Diagnostic Imaging is one such initiative. Not only does it promise to provide greater dividends for the country's investment in aerospace research, but also to enhance the American quality of life. This issue of Innovation highlights the new NASA-sponsored initiative in medical imaging. Early in 2001, NASA announced the launch of the New Partnerships in Medical Diagnostic Imaging initiative to promote the partnership and commercialization of NASA technologies in the medical imaging industry. NASA and the medical imaging industry share a number of crosscutting technologies in areas such as high-performance detectors and image-processing tools. Many of the opportunities for joint development and technology transfer to the medical imaging market also hold the promise for future spin back to NASA.

Prototype Packaged Databases and Software in Health

PubMed Central

Gardenier, Turkan K.

1980-01-01

This paper describes the recent demand for packaged databases and software for health applications in light of developments in mini-and micro-computer technology. Specific features for defining prospective user groups are discussed; criticisms generated for large-scale epidemiological data use as a means of replacing clinical trials and associated controls are posed to the reader. The available collaborative efforts for access and analysis of jointly structured health data are stressed, with recommendations for new analytical techniques specifically geared to monitoring data such as the CTSS (Cumulative Transitional State Score) generated for tacking ongoing patient status over time in clinical trials. Examples of graphic display are given from the Domestic Information Display System (DIDS) which is a collaborative multi-agency effort to computerize and make accessible user-specified U.S. and local maps relating to health, environment, socio-economic and energy data.

Thermal Barrier/Seal for Extreme Temperature Applications

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M.; Dunlap, Patrick H., Jr.; Phelps, Jack; Bauer, Paul; Bond, Bruce; McCool, Alex (Technical Monitor)

2002-01-01

Large solid rocket motors, as found on the Space Shuttle, are fabricated in segments for manufacturing considerations, bolted together, and sealed using conventional Viton O-ring seals. Similarly the nine large solid rocket motor nozzles are assembled from several different segments, bolted together, and sealed at six joint locations using conventional O-ring seals. The 5500 F combustion gases are generally kept a safe distance away from the seals by thick layers of phenolic or rubber insulation. Joint-fill compounds, including RTV (room temperature vulcanized compound) and polysulfide filler, are used to fill the joints in the insulation to prevent a direct flow-path to the O-rings. Normally these two stages of protection are enough to prevent a direct flow-path of the 900-psi hot gases from reaching the temperature-sensitive O-ring seals. However, in the current design 1 out of 15 Space Shuttle solid rocket motors experience hot gas effects on the Joint 6 wiper (sacrificial) O-rings. Also worrisome is the fact that joints have experienced heat effects on materials between the RTV and the O-rings, and in two cases O-rings have experienced heat effects. These conditions lead to extensive reviews of the post-flight conditions as part of the effort to monitor flight safety. We have developed a braided carbon fiber thermal barrier to replace the joint fill compounds in the Space Shuttle solid rocket motor nozzles to reduce the incoming 5500 F combustion gas temperature and permit only cool (approximately 100 F) gas to reach the temperature-sensitive O-ring seals. Implementation of this thermal barrier provides more robust, consistent operation with shorter turn around times between Shuttle launches.

The cyclic fatigue behavior of adhesive joints

NASA Astrophysics Data System (ADS)

Kinloch, A. J.; Toh, T.

1995-06-01

In the last six months we have: (1) Concentrated our efforts on the fatigue failure of carbon-fiber PEEK/AFl63 lap joints, and in particular we have started to predict the life time of single-lap joints under cyclic fatigue loading. The analysis is based on data obtained from double cantilever beam (DCB) fracture mechanics tests; (2) Further, we have been successful in measuring the rate of crack growth in lap joints during fatigue fracture using ultrasonic scanning; (3) Preliminary test data on the static fracture of glass-fiber reinforced poly(phenylene sulphide) (PPS)/AF163 joints have also been studied; and (4) A comparison has been made in computing the critical strain energy release rate G(sub c) for the glass-fiber PPS/AF163 joints based on the compliance method, beam theory and corrected beam theory. The last method accounts for large non-linear deflections and the associated crack root rotations along with the necessary corrections for the increase in stiffness introduced by the presence of end blocks.

Streamlining Site Cleanup in New York City

EPA Pesticide Factsheets

This joint effort, supported by the New York State Department of Environmental Conservation (NYS DEC), advances the environmental cleanup goals of PlaNYC 2030, the city's comprehensive sustainability plan.

BioMot exoskeleton - Towards a smart wearable robot for symbiotic human-robot interaction.

PubMed

Bacek, Tomislav; Moltedo, Marta; Langlois, Kevin; Prieto, Guillermo Asin; Sanchez-Villamanan, Maria Carmen; Gonzalez-Vargas, Jose; Vanderborght, Bram; Lefeber, Dirk; Moreno, Juan C

2017-07-01

This paper presents design of a novel modular lower-limb gait exoskeleton built within the FP7 BioMot project. Exoskeleton employs a variable stiffness actuator in all 6 joints, a directional-flexibility structure and a novel physical humanrobot interfacing, which allows it to deliver the required output while minimally constraining user's gait by providing passive degrees of freedom. Due to modularity, the exoskeleton can be used as a full lower-limb orthosis, a single-joint orthosis in any of the three joints, and a two-joint orthosis in a combination of any of the two joints. By employing a simple torque control strategy, the exoskeleton can be used to deliver user-specific assistance, both in gait rehabilitation and in assisting people suffering musculoskeletal impairments. The result of the presented BioMot efforts is a low-footprint exoskeleton with powerful compliant actuators, simple, yet effective torque controller and easily adjustable flexible structure.

Flaw Tolerance In Lap Shear Brazed Joints. Part 2

NASA Technical Reports Server (NTRS)

Wang, Len; Flom, Yury

2003-01-01

This paper presents results of the second part of an on-going effort to gain better understanding of defect tolerance in braze joints. In the first part of this three-part series, we mechanically tested and modeled the strength of the lap joints as a function of the overlap distance. A failure criterion was established based on the zone damage theory, which predicts the dependence of the lap joint shear strength on the overlap distance, based on the critical size of a finite damage zone or an overloaded region in the joint. In this second part of the study, we experimentally verified the applicability of the damage zone criterion on prediction of the shear strength of the lap joint and introduced controlled flaws into the lap joints. The purpose of the study was to evaluate the lap joint strength as a function of flaw size and its location through mechanical testing and nonlinear finite element analysis (FEA) employing damage zone criterion for definition of failure. The results obtained from the second part of the investigation confirmed that the failure of the ductile lap shear brazed joints occurs when the damage zone reaches approximately 10% of the overlap width. The same failure criterion was applicable to the lap joints containing flaws.

Research and Development on the Storage Ring Vacuum System for the APS Upgrade Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stillwell, B.; Brajuskovic, B.; Carter, J.

A number of research and development activities are underway at Argonne National Laboratory to build confidence in the designs for the storage ring vacuum system required for the Advanced Photon Source Up-grade project (APS-U) [1]. The predominant technical risks are: excessive residual gas pressures during operation; insufficient beam position monitor stability; excessive beam impedance; excessive heating by induced electrical surface currents; and insufficient operational reliability. Present efforts to mitigate these risks include: building and evaluating mockup assemblies; performing mechanical testing of chamber weld joints; developing computational tools; investigating design alternatives; and performing electrical bench measurements. Status of these activities andmore » some of what has been learned to date will be shared.« less

Joint Commission president outlines top strategic priorities to aid QI efforts.

PubMed

2001-06-01

At the top of the list of strategic priorities at the Joint Commission on Accreditation of Healthcare Organizations (JCAHO) is patient safety. But Dennis O'Leary, MD, president of JCAHO, says his organization faces numerous challenges beyond that, including the value of accreditation itself. According to O'Leary, the underlying issue is that only about 15% of the 150,000 health care entities currently eligible for accreditation are actually accredited.

Joint Operating Environment: Trends and Challenges for the Future Joint Force Through 2030

DTIC Science & Technology

2007-12-01

unmanned underwater vehicles loom on the horizon that can be swarmed against our ports and cities. Self - healing , networked minefields will... robots in an effort to provide the basic physical labor needed by the society. Russia has seen a major withdrawal of it population from the Far...of criminal elements. International organized crime, motivated by greed and self -interest, may increase as potential security threats to the

Procurement: Government Printing Office Supply of Microfiche to Libraries Disrupted. Report to the Chairman and Vice Chairman of the Joint Committee on Printing, U.S. Congress.

ERIC Educational Resources Information Center

General Accounting Office, Washington, DC. General Government Div.

In this report, the General Accounting Office (GAO) responds to a July 8, 1988, inquiry by the Chairman and Vice Chairman of the Joint Committee on Printing about the Government Printing Office's (GPO) efforts to acquire and supply microfiche copies of government documents to approximately 1,400 depository libraries. In August 1987, GPO had…

Defense Acquisitions: How DOD Acquires Weapon Systems and Recent Efforts to Reform the Process

DTIC Science & Technology

2010-04-23

Departments; the Chairman, Joint Chiefs of Staff (CJCS) and Joint Staff; the Unified Combatant Commands ( UCCs ); the Defense Agencies; and DOD field...Systems Congressional Research Service 24 industrialists in their own states and districts got their fair share , or more, of the military contracts...be a market for its products as a catalyst; this market was born when the comparatively small and unsophisticated U.S. peacetime ‘militia’ envisioned

Nano Enabled Thermo-Mechanical Materials in Adhesive Joints: A New Paradigm to Materials Functionality (Preprint)

DTIC Science & Technology

2006-12-01

interface as well as to minimize the interface contact resistance. There is an on- going effort by numerous researchers of dispersing conductive nano...constituents (single wall carbon nanotube (SWCNT), multi wall carbon nano tube ( MWCNT )) in polymers (adhesive) to enhance its thermal conductivity [1...propose to use vertically aligned MWCNT in joints to enhance through-thickness conductivity [10] because of its known high thermal conductivity

Population status and habitat associations of the King Rail in the midwestern United States

USGS Publications Warehouse

Bolenbaugh, Jason R.; Cooper, Tom; Brady, Ryan S.; Willard, Karen L.; Krementz, David G.

2012-01-01

The migratory population of the King Rail (Rallus elegans) has declined dramatically during the past 50 years, emphasizing the need to document the distribution and status of this species to help guide conservation efforts. In an effort to guide King Rail breeding habitat protection and restoration, a landscape suitability index (LSI) model was developed for the Upper Mississippi River and Great Lakes Region Joint Venture (JV). To validate this model, 264 sites were surveyed across the JV region in 2008 and 2009 using the National Marshbird Monitoring protocol. Two other similarly collected data sets from Wisconsin (250 sites) and Ohio (259 sites) as well as data from the Cornell Laboratory of Ornithology's eBird database were added to our data set. Sampling effort was not uniform across the study area. King Rails were detected at 29 sites with the greatest concentration in southeastern Wisconsin and northeastern Illinois. Too few detections were made to validate the LSI model. King Rail detection sites tended to have microtopographic heterogeneity, more emergent herbaceous wetland vegetation and less woody vegetation. The migrant population of the King Rail is rare and warrants additional conservation efforts to achieve stated conservation population targets.

COPDESS (Coalition for Publishing Data in the Earth & Space Sciences): An Update on Progress and Next Steps

NASA Astrophysics Data System (ADS)

Lehnert, Kerstin; Hanson, Brooks; Sallans, Andrew; Elger, Kirsten

2016-04-01

The Coalition for Publishing Data in the Earth and Space Sciences (http://www.copdess.org/) formed in October 2014 to provide an organizational framework for Earth and space science publishers and data facilities to jointly implement and promote common policies and procedures for the publication and citation of data across Earth Science journals. Since inception, it has worked to develop and promote adoption of data citation standards (e.g. FORCE11 Joint Declaration of Data Citation Principles), integrate community tools and services for greater discovery and adoption (e.g. COPDESS Directory of Repositories, https://copdessdirectory.osf.io/), and connect with related community efforts for greater transparency in research community (e.g. the Transparency and Openness Promotion Guidelines, http://cos.io/top). Following a second COPDESS workshop in Fall 2015, COPDESS is undertaking several concrete steps to increase participation and integration of efforts more deeply into the publishing and data facility workflows and to expand international participation. This talk will focus on details of specific initiatives, collection of feedback, and a call for new members. Specifically, we will present progress on the development of guidelines that aim to standardize publishers' recommended best practices by establishing "Best practices for best practices" that will allow a journal or data facility to tailor these practices to the sub-disciplines that they serve. COPDESS will further work to advance implementation of these best practices through increased outreach to and education of editors and authors. COPDESS plans to offer a Town Hall meeting at the EGU General Assembly as a forum for further information and discussion.

U.S. Geological Survey and Microsoft Cooperative Research and Development Agreement: Geospatial Data Browsing and Retrieval Site on the World Wide Web

USGS Publications Warehouse

,

1999-01-01

In May 1997, the U.S. Geological Survey (USGS) and the Microsoft Corporation of Redmond, Wash., entered into a cooperative research and development agreement (CRADA) to make vast amounts of geospatial data available to the general public through the Internet. The CRADA is a 36-month joint effort to develop a general, public-oriented browsing and retrieval site for geospatial data on the Internet. Specifically, Microsoft plans to (1) modify a large volume of USGS geospatial data so the images can be displayed quickly and easily over the Internet, (2) implement an easy-to-use interface for low-speed connections, and (3) develop an Internet Web site capable of servicing millions of users per day.

U.S. Geological Survey and Microsoft Cooperative Research and Development Agreement: Geospatial Data Browsing and Retrieval Site on the World Wide Web

USGS Publications Warehouse

,

1998-01-01

In May 1997, the U.S. Geological Survey (USGS) and the Microsoft Corporation of Redmond, Wash., entered into a cooperative research and development agreement (CRADA) to make vast amounts of geospatial data available to the general public through the Internet. The CRADA is a 36-month joint effort to develop a general, public-oriented browsing and retrieval site for geospatial data on the Internet. Specifically, Microsoft plans to (1) modify a large volume of USGS geospatial data so the images can be displayed quickly and easily over the Internet, (2) implement an easy-to-use interface for low-speed connections, and (3) develop an Internet Web site capable of servicing millions of users per day.

MEDISE: A macroeconomic model for energy planning in Costa Rica

DOE Office of Scientific and Technical Information (OSTI.GOV)

Booth, S.R.; Leiva, C.L.

This report describes the development and results of MEDISE, an econometric macroeconomic model for energy planning in Costa Rica. The model is a simultaneous system of 19 equations that was constructed using ENERPLAN, an energy planning tool developed by the United Nations for use in developing countries. The equations were estimated using regression analysis on a data time series of 1966 to 1984. ENERPLAN's model solution package was used to obtain forecasts of 19 economic variables from 1985 to 2005. the modeling effort was conducted jointly by Los Alamos Central American Energy and Resources Project (CAP) personnel and the Energymore » Sector Directorate of Costa Rica during 1986. The CAP was funded by the US Agency for International Development. 6 refs., 3 figs., 11 tabs.« less

Analysis of the Lenticular Jointed MARSIS Antenna Deployment

NASA Technical Reports Server (NTRS)

Mobrem, Mehran; Adams, Douglas S.

2006-01-01

This paper summarizes important milestones in a yearlong comprehensive effort which culminated in successful deployments of the MARSIS antenna booms in May and June of 2005. Experimentally measured straight section and hinge properties are incorporated into specialized modeling techniques that are used to simulate the boom lenticular joints. System level models are exercised to understand the boom deployment dynamics and spacecraft level implications. Discussion includes a comparison of ADAMS simulation results to measured flight data taken during the three boom deployments. Important parameters that govern lenticular joint behavior are outlined and a short summary of lessons learned and recommendations is included to better understand future applications of this technology.

An ecosystem services framework to support both practical conservation and economic development.

PubMed

Tallis, Heather; Kareiva, Peter; Marvier, Michelle; Chang, Amy

2008-07-15

The core idea of the Millennium Ecosystem Assessment is that the human condition is tightly linked to environmental condition. This assertion suggests that conservation and development projects should be able to achieve both ecological and social progress without detracting from their primary objectives. Whereas "win-win" projects that achieve both conservation and economic gains are a commendable goal, they are not easy to attain. An analysis of World Bank projects with objectives of alleviating poverty and protecting biodiversity revealed that only 16% made major progress on both objectives. Here, we provide a framework for anticipating win-win, lose-lose, and win-lose outcomes as a result of how people manage their ecosystem services. This framework emerges from detailed explorations of several case studies in which biodiversity conservation and economic development coincide and cases in which there is joint failure. We emphasize that scientific advances around ecosystem service production functions, tradeoffs among multiple ecosystem services, and the design of appropriate monitoring programs are necessary for the implementation of conservation and development projects that will successfully advance both environmental and social goals. The potentially bright future of jointly advancing ecosystem services, conservation, and human well-being will be jeopardized unless a global monitoring effort is launched that uses the many ongoing projects as a grand experiment.

An ecosystem services framework to support both practical conservation and economic development

PubMed Central

Tallis, Heather; Kareiva, Peter; Marvier, Michelle; Chang, Amy

2008-01-01

The core idea of the Millennium Ecosystem Assessment is that the human condition is tightly linked to environmental condition. This assertion suggests that conservation and development projects should be able to achieve both ecological and social progress without detracting from their primary objectives. Whereas “win–win” projects that achieve both conservation and economic gains are a commendable goal, they are not easy to attain. An analysis of World Bank projects with objectives of alleviating poverty and protecting biodiversity revealed that only 16% made major progress on both objectives. Here, we provide a framework for anticipating win–win, lose–lose, and win–lose outcomes as a result of how people manage their ecosystem services. This framework emerges from detailed explorations of several case studies in which biodiversity conservation and economic development coincide and cases in which there is joint failure. We emphasize that scientific advances around ecosystem service production functions, tradeoffs among multiple ecosystem services, and the design of appropriate monitoring programs are necessary for the implementation of conservation and development projects that will successfully advance both environmental and social goals. The potentially bright future of jointly advancing ecosystem services, conservation, and human well-being will be jeopardized unless a global monitoring effort is launched that uses the many ongoing projects as a grand experiment. PMID:18621702

Introducing Object-Oriented Concepts into GSI

NASA Technical Reports Server (NTRS)

Guo, Jing; Todling, Ricardo

2017-01-01

Enhancements are now being made to the Gridpoint Statistical Interpolation (GSI) data assimilation system to expand its capabilities. This effort opens the way for broadening the scope of GSI's applications by using some standard object-oriented features in Fortran, and represents a starting point for the so-called GSI refactoring, as a part of the Joint Effort for Data-assimilationI ntegration (JEDI) project of JCSDA.

Fiscal Year 1962-63 SNAP 10A Program Proposal (Revised August 15, 1961)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1961-08-15

The SNAPSHOT program is a joint AEC-USAF effort to flight test SNAP units. SNAPSHOT flights are intended to establish the capabilities of nuclear auxiliary power so that its future use in space systems can be programmed with confidence overcoming both technical and psychological barriers. A set of flight tests for the SNAP 10A system form a part of this effort.

History of osteochondral allograft transplantation.

PubMed

Nikolaou, V S; Giannoudis, P V

2017-07-01

Osteochondral defects or injuries represent the most challenging entities to treat, especially when occur to young and active patients. For centuries, it has been recognized that such defects are almost impossible to treat. However, surgeons have never stopped the effort to develop reliable methods to restore articular cartilage and salvage the endangered joint function. Osteochondral allograft transplantation in human was first introduced by Eric Lexer in 1908. Since that era, several pioneers have been worked in the field of osteochondral allotransplantation, presenting and developing the basic research, the methodology and the surgical techniques. Herein we present in brief, the history and the early clinical results of osteochondral allograft transplantation in human. Copyright © 2017 Elsevier Ltd. All rights reserved.

Wireless Subsurface Microsensors for Health Monitoring of Thermal Protection Systems on Hypersonic Vehicles

NASA Technical Reports Server (NTRS)

Milos, Frank S.; Watters, David G.; Pallix, Joan B.; Bahr, Alfred J.; Huestis, David L.; Arnold, Jim (Technical Monitor)

2001-01-01

Health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles in order to reduce life cycle costs, to increase safety margins, and to improve mission reliability. NASA Ames is leading the effort to develop inspection and health management technologies for thermal protection systems. This paper summarizes a joint project between NASA Ames and SRI International to develop 'SensorTags,' radio frequency identification devices coupled with event-recording sensors, that can be embedded in the thermal protection system to monitor temperature or other quantities of interest. Two prototype SensorTag designs containing thermal fuses to indicate a temperature overlimit are presented and discussed.

Material Studies Related to the Use of NaK Heat Exchangers Coupled to Stirling Heater Heads

NASA Technical Reports Server (NTRS)

Locci, Ivan E.; Bowman, Cheryl L.; Geng, Steven M.; Robbie, Malcolm G.

2011-01-01

NASA has been supporting design studies and technology development that could provide power to an outpost on the Moon, Mars, or an asteroid. Technology development efforts have included fabrication and evaluation of components used in a Stirling engine power conversion system. Destructive material evaluation was performed on a NaK shell heat exchanger that was developed by the NASA Glenn Research Center (GRC) and integrated with a commercial 1 kWe Stirling convertor from Sunpower Incorporated. The NaK Stirling test demonstrated Stirling convertor electrical power generation using a pumped liquid metal heat source under thermal conditions that represent the heat exchanger liquid metal loop in a Fission Power Systems (FPS) reactor. The convertors were operated for a total test time of 66 hr at a maximum temperature of 823 K. After the test was completed and NaK removed, the heat exchanger assembly was sectioned to evaluate any material interactions with the flowing liquid metal. Several dissimilar-metal braze joint options, crucial for the heat exchanger transfer path, were also investigated. A comprehensive investigation was completed and lessons learned for future heat exchanger development efforts are discussed.

Government of Canada Initiatives in Support of the Joint Convention

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, P.A.; Metcalfe, D.E.; Lojk, R.

The Government of Canada strongly supported international efforts to bring into force the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management (the Joint Convention), and was the second country to ratify it. The Joint Convention places a number of obligations on Contracting Parties aimed at achieving and maintaining a high level of safety worldwide in spent fuel and radioactive waste management, ensuring that effective defenses against potential hazards are in place during all management stages, preventing accidents with radiological consequences and mitigating their consequences should they occur. In addition to establishingmore » and maintaining a modem regulatory framework and an independent regulatory body through the 2000 Nuclear Safety and Control Act, the Government of Canada has implemented a number of initiatives that address its responsibilities and serve to further enhance Canada's compliance with the Joint Convention. For nuclear fuel waste, the Government of Canada brought into force the Nuclear Fuel Waste Act in 2002 to require waste owners to develop, fund, organize and implement a long-term solution for Canada's nuclear fuel waste. The Act clearly reserves for Government the decision on the solution to be implemented in the best interests of Canadians, as well as oversight to ensure that waste owners are fulfilling their responsibilities. In the case of low-level radioactive waste, long-term solutions are being developed to ensure the protection of health, safety, and the environment, both now and in the future. Regarding uranium mine and mill tailings, current operators have state-of-the-art waste management facilities in place. The Government of Canada works with provincial governments to ensure that any potential abandoned or legacy mines sites where no owner can be held responsible are safely decommissioned and managed over the long term. (authors)« less

Early Osteoarthritis of the Trapeziometacarpal Joint Is Not Associated With Joint Instability during Typical Isometric Loading

PubMed Central

Halilaj, Eni; Moore, Douglas C.; Patel, Tarpit K.; Ladd, Amy L.; Weiss, Arnold-Peter C.; Crisco, Joseph J.

2015-01-01

The saddle-shaped trapeziometacarpal (TMC) joint contributes importantly to the function of the human thumb. A balance between mobility and stability is essential in this joint, which experiences high loads and is prone to osteoarthritis (OA). Since instability is considered a risk factor for TMC OA, we assessed TMC joint instability during the execution of three isometric functional tasks (key pinch, jar grasp, and jar twist) in 76 patients with early TMC OA and 44 asymptomatic controls. Computed tomography images were acquired while subjects held their hands relaxed and while they applied 80% of their maximum effort for each task. Six degree-of-freedom rigid body kinematics of the metacarpal with respect to the trapezium from the unloaded to the loaded task positions were computed in terms of a TMC joint coordinate system. Joint instability was expressed as a function of the metacarpal translation and the applied force. We found that the TMC joint was more unstable during a key pinch task than during a jar grasp or a jar twist task. Sex, age, and early OA did not have an effect on TMC joint instability, suggesting that instability during these three tasks is not a predisposing factor in TMC OA. PMID:25941135

Are joint health plans effective for coordination of health services? An analysis based on theory and Danish pre-reform results

PubMed Central

Strandberg-Larsen, Martin; Bernt Nielsen, Mikkel; Krasnik, Allan

2007-01-01

Background Since 1994 formal health plans have been used for coordination of health care services between the regional and local level in Denmark. From 2007 a substantial reform has changed the administrative boundaries of the system and a new tool for coordination has been introduced. Purpose To assess the use of the pre-reform health plans as a tool for strengthening coordination, quality and preventive efforts between the regional and local level of health care. Methods A survey addressed to: all counties (n=15), all municipalities (n=271) and a randomised selected sample of general practitioners (n=700). Results The stakeholders at the administrative level agree that health plans have not been effective as a tool for coordination. The development of health plans are dominated by the regional level. At the functional level 27 percent of the general practitioners are not familiar with health plans. Among those familiar with health plans 61 percent report that health plans influence their work to only a lesser degree or not at all. Conclusion Joint health planning is needed to achieve coordination of care. Efforts must be made to overcome barriers hampering efficient whole system planning. Active policies emphasising the necessity of health planning, despite involved cost, are warranted to insure delivery of care that benefits the health of the population. PMID:17925882

IJEMS: Iowa Joint Experiment in Microgravity Solidification

NASA Technical Reports Server (NTRS)

Bendle, John R.; Mashl, Steven J.; Hardin, Richard A.

1995-01-01

The Iowa Joint Experiment in Microgravity Solidification (IJEMS) is a cooperative effort between Iowa State University and the University of Iowa to study the formation of metal-matrix composites in a microgravity environment. Of particular interest is the interaction between the solid/liquid interface and the particles in suspension. The experiment is scheduled to fly on STS-69, Space Shuttle Endeavor on August 3, 1995. This project is unique in its heavy student participation and cooperation between the universities involved.

Let’s Get Counterinsurgency Right: Collective Action Theory in Joint Publication 3-24

DTIC Science & Technology

2015-04-01

Defense (DOD) revised its Joint Publication 3- 24: Counterinsurgency to refine its definition of counterinsurgency, introduce “tenets and precepts of...updates.21 JP 3-24’s refined definitions make two opposing cases for the role of the population. On one hand, “[Counterinsurgency] COIN is a[n]…effort...new definitions of counterinsurgency seem contradictory, its introduction of “tenets and precepts” further complicates the doctrine’s usefulness

Construction and Development of CRM Technology and Industry Chain in China

NASA Astrophysics Data System (ADS)

Liu, Chunnian; Wang, Yonglong; Pan, Qin

CRM is any application or initiative designed to help an organization optimize interactions with customers, suppliers, or prospects via one or more touch points. CRM has been interpreted and used in different ways by researchers in the various disciplines and researchers have identified a variety of technologies related to CRM. This paper highlights the implementation from the technology level and contributes to some successful factors in CRM application. The development of CRM is not fully developed in China. There are many critical factors that determine the CRM market development. Construction and development of CRM industry chain in China is a valuable research field and the paper provided some suggestions and analyses on it. In future, it requires our joint efforts of many aspects from every walk of life to make sure that CRM industry chain can improve and maturate gradually.

2015 Gout classification criteria: an American College of Rheumatology/European League Against Rheumatism collaborative initiative

PubMed Central

Neogi, Tuhina; Jansen, Tim L Th A; Dalbeth, Nicola; Fransen, Jaap; Schumacher, H Ralph; Berendsen, Dianne; Brown, Melanie; Choi, Hyon; Edwards, N Lawrence; Janssens, Hein J E M; Lioté, Frédéric; Naden, Raymond P; Nuki, George; Ogdie, Alexis; Perez-Ruiz, Fernando; Saag, Kenneth; Singh, Jasvinder A; Sundy, John S; Tausche, Anne-Kathrin; Vaquez-Mellado, Janitzia; Yarows, Steven A; Taylor, William J

2015-01-01

Objective Existing criteria for the classification of gout have suboptimal sensitivity and/or specificity, and were developed at a time when advanced imaging was not available. The current effort was undertaken to develop new classification criteria for gout. Methods An international group of investigators, supported by the American College of Rheumatology and the European League Against Rheumatism, conducted a systematic review of the literature on advanced imaging of gout, a diagnostic study in which the presence of monosodium urate monohydrate (MSU) crystals in synovial fluid or tophus was the gold standard, a ranking exercise of paper patient cases, and a multi-criterion decision analysis exercise. These data formed the basis for developing the classification criteria, which were tested in an independent data set. Results The entry criterion for the new classification criteria requires the occurrence of at least one episode of peripheral joint or bursal swelling, pain, or tenderness. The presence of MSU crystals in a symptomatic joint/bursa (ie, synovial fluid) or in a tophus is a sufficient criterion for classification of the subject as having gout, and does not require further scoring. The domains of the new classification criteria include clinical (pattern of joint/bursa involvement, characteristics and time course of symptomatic episodes), laboratory (serum urate, MSU-negative synovial fluid aspirate), and imaging (double-contour sign on ultrasound or urate on dual-energy CT, radiographic gout-related erosion). The sensitivity and specificity of the criteria are high (92% and 89%, respectively). Conclusions The new classification criteria, developed using a data-driven and decision-analytic approach, have excellent performance characteristics and incorporate current state-of-the-art evidence regarding gout. PMID:26359487

2015 Gout Classification Criteria: An American College of Rheumatology/European League Against Rheumatism Collaborative Initiative

PubMed Central

Jansen, Tim L. Th. A.; Dalbeth, Nicola; Fransen, Jaap; Schumacher, H. Ralph; Berendsen, Dianne; Brown, Melanie; Choi, Hyon; Edwards, N. Lawrence; Janssens, Hein J. E. M.; Lioté, Frédéric; Naden, Raymond P.; Nuki, George; Ogdie, Alexis; Perez‐Ruiz, Fernando; Saag, Kenneth; Singh, Jasvinder A.; Sundy, John S.; Tausche, Anne‐Kathrin; Vaquez‐Mellado, Janitzia; Yarows, Steven A.; Taylor, William J.

2015-01-01

Objective Existing criteria for the classification of gout have suboptimal sensitivity and/or specificity, and were developed at a time when advanced imaging was not available. The current effort was undertaken to develop new classification criteria for gout. Methods An international group of investigators, supported by the American College of Rheumatology and the European League Against Rheumatism, conducted a systematic review of the literature on advanced imaging of gout, a diagnostic study in which the presence of monosodium urate monohydrate (MSU) crystals in synovial fluid or tophus was the gold standard, a ranking exercise of paper patient cases, and a multicriterion decision analysis exercise. These data formed the basis for developing the classification criteria, which were tested in an independent data set. Results The entry criterion for the new classification criteria requires the occurrence of at least 1 episode of peripheral joint or bursal swelling, pain, or tenderness. The presence of MSU crystals in a symptomatic joint/bursa (i.e., synovial fluid) or in a tophus is a sufficient criterion for classification of the subject as having gout, and does not require further scoring. The domains of the new classification criteria include clinical (pattern of joint/bursa involvement, characteristics and time course of symptomatic episodes), laboratory (serum urate, MSU‐negative synovial fluid aspirate), and imaging (double‐contour sign on ultrasound or urate on dual‐energy computed tomography, radiographic gout‐related erosion). The sensitivity and specificity of the criteria are high (92% and 89%, respectively). Conclusion The new classification criteria, developed using a data‐driven and decision analytic approach, have excellent performance characteristics and incorporate current state‐of‐the‐art evidence regarding gout. PMID:26352873

Mechanical stimulation of mesenchymal stem cells: Implications for cartilage tissue engineering.

PubMed

Fahy, Niamh; Alini, Mauro; Stoddart, Martin J

2018-01-01

Articular cartilage is a load-bearing tissue playing a crucial mechanical role in diarthrodial joints, facilitating joint articulation, and minimizing wear. The significance of biomechanical stimuli in the development of cartilage and maintenance of chondrocyte phenotype in adult tissues has been well documented. Furthermore, dysregulated loading is associated with cartilage pathology highlighting the importance of mechanical cues in cartilage homeostasis. The repair of damaged articular cartilage resulting from trauma or degenerative joint disease poses a major challenge due to a low intrinsic capacity of cartilage for self-renewal, attributable to its avascular nature. Bone marrow-derived mesenchymal stem cells (MSCs) are considered a promising cell type for cartilage replacement strategies due to their chondrogenic differentiation potential. Chondrogenesis of MSCs is influenced not only by biological factors but also by the environment itself, and various efforts to date have focused on harnessing biomechanics to enhance chondrogenic differentiation of MSCs. Furthermore, recapitulating mechanical cues associated with cartilage development and homeostasis in vivo, may facilitate the development of a cellular phenotype resembling native articular cartilage. The goal of this review is to summarize current literature examining the effect of mechanical cues on cartilage homeostasis, disease, and MSC chondrogenesis. The role of biological factors produced by MSCs in response to mechanical loading will also be examined. An in-depth understanding of the impact of mechanical stimulation on the chondrogenic differentiation of MSCs in terms of endogenous bioactive factor production and signaling pathways involved, may identify therapeutic targets and facilitate the development of more robust strategies for cartilage replacement using MSCs. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:52-63, 2018. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

Stellar Snowflake Cluster

NASA Image and Video Library

2005-12-22

Newborn stars, hidden behind thick dust, are revealed in this image of a section of the Christmas Tree cluster from NASA Spitzer Space Telescope, created in joint effort between Spitzer infrared array camera and multiband imaging photometer instrument

F-Gas Partnership Programs

EPA Pesticide Factsheets

Provides basic information and resources for the Fluorinated Gas Partnership Programs, which were launched as a joint effort by EPA and industry groups to reduce the amount of fluorinated gases emitted through a variety of industrial processes.

Joint pricing, inventory, and preservation decisions for deteriorating items with stochastic demand and promotional efforts

NASA Astrophysics Data System (ADS)

Soni, Hardik N.; Chauhan, Ashaba D.

2018-03-01

This study models a joint pricing, inventory, and preservation decision-making problem for deteriorating items subject to stochastic demand and promotional effort. The generalized price-dependent stochastic demand, time proportional deterioration, and partial backlogging rates are used to model the inventory system. The objective is to find the optimal pricing, replenishment, and preservation technology investment strategies while maximizing the total profit per unit time. Based on the partial backlogging and lost sale cases, we first deduce the criterion for optimal replenishment schedules for any given price and technology investment cost. Second, we show that, respectively, total profit per time unit is concave function of price and preservation technology cost. At the end, some numerical examples and the results of a sensitivity analysis are used to illustrate the features of the proposed model.

River basin management, described for the example of the Emschergenossenschaft.

PubMed

Baumgart, H C; Sperling, F; Stemplewski, J

2003-01-01

Considerable problems concerning drainage capacity made it necessary, at the beginning of the 20th Century, to make a joint public-private effort, because the existence of the Ruhr Area as an industrial location was endangered. By Prussian law a co-operative was established for wastewater and drainage-management of the entire Emscher river system. In the past the Emscher Association and the later founded Lippe Association have proved to be the best instrument to cope with the wastewater problems of a densely-populated industrial area. In recent time, the Emscher area is undergoing fundamental structural changes. To increase its attractiveness increased efforts are needed for a modernisation of the wastewater transport and treatment system. To deal with the various and complex tasks to reshape the Emscher system, the joint association again provides a highly efficient and competent instrument.

A Method to Accurately Estimate the Muscular Torques of Human Wearing Exoskeletons by Torque Sensors

PubMed Central

Hwang, Beomsoo; Jeon, Doyoung

2015-01-01

In exoskeletal robots, the quantification of the user’s muscular effort is important to recognize the user’s motion intentions and evaluate motor abilities. In this paper, we attempt to estimate users’ muscular efforts accurately using joint torque sensor which contains the measurements of dynamic effect of human body such as the inertial, Coriolis, and gravitational torques as well as torque by active muscular effort. It is important to extract the dynamic effects of the user’s limb accurately from the measured torque. The user’s limb dynamics are formulated and a convenient method of identifying user-specific parameters is suggested for estimating the user’s muscular torque in robotic exoskeletons. Experiments were carried out on a wheelchair-integrated lower limb exoskeleton, EXOwheel, which was equipped with torque sensors in the hip and knee joints. The proposed methods were evaluated by 10 healthy participants during body weight-supported gait training. The experimental results show that the torque sensors are to estimate the muscular torque accurately in cases of relaxed and activated muscle conditions. PMID:25860074

Composite Overwrapped Pressure Vessels: Database Extension Task 3.0 and Impact Damage Effects Control Task 8.0

NASA Technical Reports Server (NTRS)

Beeson, Harold D.; Davis, Dennis D.; Ross, William L., Sr.; Tapphorn, Ralph M.

2002-01-01

This document represents efforts accomplished at the NASA Johnson Space Center White Sands Test Facility (WSTF) in support of the Enhanced Technology for Composite Overwrapped Pressure Vessels (COPV) Program, a joint research and technology effort among the U.S. Air Force, NASA, and the Aerospace Corporation. WSTF performed testing for several facets of the program. Testing that contributed to the Task 3.0 COPV database extension objective included baseline structural strength, failure mode and safe-life, impact damage tolerance, sustained load/impact effect, and materials compatibility. WSTF was also responsible for establishing impact protection and control requirements under Task 8.0 of the program. This included developing a methodology for establishing an impact control plan. Seven test reports detail the work done at WSTF. As such, this document contributes to the database of information regarding COPV behavior that will ensure performance benefits and safety are maintained throughout vessel service life.

Fretting Fatigue of Single Crystal/Polycrystalline Nickel Subjected to Blade/Disk Contact Loading

NASA Astrophysics Data System (ADS)

Matlik, J. F.; Murthy, H.; Farris, T. N.

2002-01-01

Fretting fatigue describes the formation and growth of cracks at the edge-of-contact of nominally clamped components subjected to cyclic loading. Components that are known to be subject to fretting fatigue include riveted lap joints and blade/disk contacts in launch vehicle turbomachinery. Recent efforts have shown that conventional mechanics tools, both fatigue and fracture based, can be used to model fretting fatigue experiments leading to successful life predictions. In particular, experiments involving contact load configurations similar to those that occur in the blade/disk connection of gas turbine engines have been performed extensively. Predictions of fretting fatigue life have been compared favorably to experimental observations [1]. Recent efforts are aimed at performing experiments at higher temperatures as shown in the photograph below along with a sample fracture surface. The talk will describe the status of these experiments as will as model developments relevant to the single crystal material properties.

Agreement for NASA/OAST - USAF/AFSC space interdependency on spacecraft environment interaction

NASA Technical Reports Server (NTRS)

Pike, C. P.; Stevens, N. J.

1980-01-01

A joint AF/NASA comprehensive program on spacecraft environment interactions consists of combined contractual and in house efforts aimed at understanding spacecraft environment ineraction phenomena and relating ground test results to space conditions. Activities include: (1) a concerted effort to identify project related environmental interactions; (2) a materials investigation to measure the basic properties of materials and develop or modify materials as needed; and (3) a ground simulation investigation to evaluate basic plasma interaction phenomena and provide inputs to the analytical modeling investigation. Systems performance is evaluated by both ground tests and analysis. There is an environmental impact investigation to determine the effect of future large spacecraft on the charged particle environment. Space flight investigations are planned to verify the results. The products of this program are test standards and design guidelines which summarize the technology, specify test criteria, and provide techniques to minimize or eliminate system interactions with the charged particle environment.

Key Role of M.G. Nakhodkin’s Insight and Inspiration in Development of UHV STM-Related Techniques and Methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyubinetsky, Igor

2015-02-15

In this contribution I briefly describe my joint efforts and experiences with M.G. Nakhodkin in the field of scanning tunneling microscopy (STM) including a construction of the home-built microscopes, application of this technique in various scientific endevours, as well as fruitfull and enlightening discusions. Our co-operation was focused on the novel aspects of STM probes preparation and conditioning, coupling the STM junction with laser irradiation, STM-based nanolithography, and also on collaboration at the international scale with M.G. Nakhodkin and members of his scientific group.

United States/Russia space cooperation documentary

NASA Astrophysics Data System (ADS)

1993-12-01

This video documents the initiative to develop a multinational, permanent space research laboratory. Historical background on the U.S. and Soviet manned space flight program as well as joint efforts such as the Apollo-Soyuz link up is shown. The current initiative will begin with collaborative missions involving NASA's space shuttle and Russia's Mir space station, and culminate in a permanently manned space station involving the U.S., Russia, Japan, Canada, and ESA. Shown are computer simulations of the proposed space station. Commentary is provided by the NASA administrator, former astronauts, cosmonauts, and Russian and American space experts.

Jaasc Cooperation League for Education and Public Outreach

NASA Astrophysics Data System (ADS)

Watanabe, Jun-Ichi; JAASC Committee

The JAASC Japanese Astronomy Aeronautical Science Space Science cooperation league has been established in 2000 among the related institutes for education and public outreach. The participating institutes are National Astronomical Observatory of Japan Institute of Space and Astronautical Science National Space Development Agency of Japan National Aerospace Laboratory of Japan Young Astronomers Club Japan Science and Technology Corporation and Japan Space Forum. These institutes started several joint efforts such as making web site for beginners in general public or educational materials for junior high school. This is a challenging trial for Japanese institutes to cooperate beyond the barrier of the

United States/Russia Space Cooperation Documentary

NASA Technical Reports Server (NTRS)

1993-01-01

This video documents the initiative to develop a multinational, permanent space research laboratory. Historical background on the U.S. and Soviet manned space flight program as well as joint efforts such as the Apollo-Soyuz link up is shown. The current initiative will begin with collaborative missions involving NASA's space shuttle and Russia's Mir space station, and culminate in a permanently manned space station involving the U.S., Russia, Japan, Canada, and ESA. Shown are computer simulations of the proposed space station. Commentary is provided by the NASA administrator, former astronauts, cosmonauts, and Russian and American space experts.

Functionally graded bio-ceramic reinforced PVA hydrogel composites for knee joint artificial cartilages

NASA Astrophysics Data System (ADS)

Kumar, G. C. Mohan

2018-04-01

Research progress in materials science for bio-based materials for cartilage repair or supportive to host tissue has become a fashionable, worldwide. Few efforts in biomedical engineering has attempted in the development of newer biomaterials successfully. Bio ceramics, a class of materials been used in particulate form as a reinforcement with polymers those ensure its biocompatibility. Every artificial biomedical system has to meet the minimum in Vitro requirements for successful application. Equally the biological behavior of normal and diseased tissues is also essential to understand the artificial systems to human body.

PHASE II CALDERON PROCESS TO PRODUCE DIRECT REDUCED IRON RESEARCH AND DEVELOPMENT PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albert Calderon

2003-04-28

This project was initially targeted to the making of coke for blast furnaces by using proprietary technology of Calderon in a phased approach, and Phase I was successfully completed. The project was then re-directed to the making of iron units. U.S. Steel teamed up with Calderon for a joint effort which will last 30 months to produce directly reduced iron with the potential of converting it into molten iron or steel consistent with the Roadmap recommendations of 1998 prepared by the Steel Industry in cooperation with the Department of Energy.

PHASE II CALDERON PROCESS TO PRODUCE DIRECT REDUCED IRON RESEARCH AND DEVELOPMENT PROJECT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albert Calderon

2003-01-28

This project was initially targeted to the making of coke for blast furnaces by using proprietary technology of Calderon in a phased approach, and Phase I was successfully completed. The project was then re-directed to the making of iron units. U.S. Steel teamed up with Calderon for a joint effort which will last 30 months to produce directly reduced iron with the potential of converting it into molten iron or steel consistent with the Roadmap recommendations of 1998 prepared by the Steel Industry in cooperation with the Department of Energy.

Commonwealth of Pennsylvania. [Establishment of hazardous waste facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Environmental Resources Secretary Arthur A. Davis and Commerce Secretary Raymond R. Christman have announced a joint initiative to establish commercial hazardous waste treatment and disposal facilities Pennsylvania. The state Hazardous Sites Cleanup Act, which Gov. Robert P. Casey signed into law last October, called for accelerated efforts in this regard. These included an expedited permitting process for facilities, requiring the Department of Environmental Resources (DER) to appoint a special sitting team to review permit applications, and designation of sitting coordinator within the Department of Commerce to identify potential developers of the facilities and encourage them to operate within Pennsylvania.

Real-time Stack Monitoring at the BaTek Medical Isotope Production Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

McIntyre, Justin I.; Agusbudiman, A.; Cameron, Ian M.

2016-04-01

Radioxenon emissions from radiopharmaceutical production are a major source of background concentrations affecting the radioxenon detection systems of the International Monitoring System (IMS). Collection of real-time emissions data from production facilities makes it possible to screen out some medical isotope signatures from the IMS radioxenon data sets. This paper describes an effort to obtain and analyze real-time stack emissions data with the design, construction and installation of a small stack monitoring system developed by a joint CTBTO-IDC, BATAN, and PNNL team at the BaTek medical isotope production facility near Jakarta, Indonesia.

Military Personnel: DOD Is Expanding Combat Service Opportunities for Women, but Should Monitor Long-Term Integration Progress

DTIC Science & Technology

2015-07-01

steps to identify and mitigate potential challenges; (2) extent the services’ efforts to validate gender -neutral occupational standards are...to address statutory and Joint Staff requirements for validating gender -neutral occupational standards. GAO identified five elements required for...SOCOM Have Studies Underway to Validate Gender -Neutral Occupational Standards 21 DOD Is Providing Oversight of Integration Efforts, but Has Not

Inequity responses of monkeys modified by effort

PubMed Central

van Wolkenten, Megan; Brosnan, Sarah F.; de Waal, Frans B. M.

2007-01-01

Without joint benefits, joint actions could never have evolved. Cooperative animals need to monitor closely how large a share they receive relative to their investment toward collective goals. This work documents the sensitivity to reward division in brown, or tufted, capuchin monkeys (Cebus apella). In addition to confirming previous results with a larger subject pool, this work rules out several alternative explanations and adds data on effort sensitivity. Thirteen adult monkeys exchanged tokens for rewards, showing negative reactions to receiving a less-favored reward than their partner. Because their negative reaction could not be attributed to the mere visibility of better rewards (greed hypothesis) nor to having received such rewards in the immediate past (frustration hypothesis), it must have been caused by seeing their partner obtain the better reward. Effort had a major effect in that by far the lowest level of performance in the entire study occurred in subjects required to expend a large effort while at the same time seeing their partner receive a better reward. It is unclear whether this effort–effect was based on comparisons with the partner, but it added significantly to the intensity of the inequity response. These effects are as expected if the inequity response evolved in the context of cooperative survival strategies. PMID:18000045

Inequity-aversion and relative kindness intention jointly determine the expenditure of effort in project teams

PubMed Central

Rapoport, Amnon; Zhao, Rui

2017-01-01

The literature on team cooperation has neglected the effects of relative kindness intention on cooperation, which we measure by comparing the kindness intentions of an agent to her group members to the kindness shown by other members to this same agent. We argue that the agent’s emotional reaction to material payoff inequity is not constant, but rather affected by her relative kindness intention. Then, we apply the model to team projects with multiple partners and investigate how inequity-aversion and relative kindness intention jointly influence team cooperation. We first consider the case of homogeneous agents, where their marginal productivity levels and technical capacities are the same, and then consider the case of heterogeneous agents, where their marginal productivity levels and technical capacities are not the same. Our results show that inequity-aversion has no effect on effort expenditure in the former case, but does affect it in the latter case. The consideration of relative kindness intention may impact the agents’ optimal cooperative effort expenditure when their technical capacities are different. In addition, it is beneficial for team cooperation, and might not only reduce the negative impact but also enhance the positive impact of inequity-aversion on the agents’ effort expenditures. PMID:28459853

Upper extremity interaction with a helicopter side airbag: injury criteria for dynamic hyperextension of the female elbow joint.

PubMed

Duma, Stefan M; Hansen, Gail A; Kennedy, Eric A; Rath, Amber L; McNally, Craig; Kemper, Andrew R; Smith, Eric P; Brolinson, P Gunnar; Stitzel, Joel D; Davis, Martin B; Bass, Cameron R; Brozoski, Frederick T; McEntire, B Joseph; Alem, Nabih M; Crowley, John S

2004-11-01

This paper describes a three part analysis to characterize the interaction between the female upper extremity and a helicopter cockpit side airbag system and to develop dynamic hyperextension injury criteria for the female elbow joint. Part I involved a series of 10 experiments with an original Army Black Hawk helicopter side airbag. A 5(th) percentile female Hybrid III instrumented upper extremity was used to demonstrate side airbag upper extremity loading. Two out of the 10 tests resulted in high elbow bending moments of 128 Nm and 144 Nm. Part II included dynamic hyperextension tests on 24 female cadaver elbow joints. The energy source was a drop tower utilizing a three-point bending configuration to apply elbow bending moments matching the previously conducted side airbag tests. Post-test necropsy showed that 16 of the 24 elbow joint tests resulted in injuries. Injury severity ranged from minor cartilage damage to more moderate joint dislocations and severe transverse fractures of the distal humerus. Peak elbow bending moments ranged from 42.4 Nm to 146.3 Nm. Peak bending moment proved to be a significant indicator of any elbow injury (p = 0.02) as well as elbow joint dislocation (p = 0.01). Logistic regression analyses were used to develop single and multiple variate injury risk functions. Using peak moment data for the entire test population, a 50% risk of obtaining any elbow injury was found at 56 Nm while a 50% risk of sustaining an elbow joint dislocation was found at 93 Nm for the female population. These results indicate that the peak elbow bending moments achieved in Part I are associated with a greater than 90% risk for elbow injury. Subsequently, the airbag was re-designed in an effort to mitigate this as well as the other upper extremity injury risks. Part III assessed the redesigned side airbag module to ensure injury risks had been reduced prior to implementing the new system. To facilitate this, 12 redesigned side airbag deployments were conducted using the same procedures as Part I. Results indicate that the re-designed side airbag has effectively mitigated elbow injury risks induced by the original side airbag design. It is anticipated that this study will provide researchers with additional injury criteria for assessing upper extremity injury risk caused by both military and automotive side airbag deployments.

Tissue material properties and computational modelling of the human tibiofemoral joint: a critical review

PubMed Central

Akhtar, Riaz; Comerford, Eithne J.; Bates, Karl T.

2018-01-01

Understanding how structural and functional alterations of individual tissues impact on whole-joint function is challenging, particularly in humans where direct invasive experimentation is difficult. Finite element (FE) computational models produce quantitative predictions of the mechanical and physiological behaviour of multiple tissues simultaneously, thereby providing a means to study changes that occur through healthy ageing and disease such as osteoarthritis (OA). As a result, significant research investment has been placed in developing such models of the human knee. Previous work has highlighted that model predictions are highly sensitive to the various inputs used to build them, particularly the mathematical definition of material properties of biological tissues. The goal of this systematic review is two-fold. First, we provide a comprehensive summation and evaluation of existing linear elastic material property data for human tibiofemoral joint tissues, tabulating numerical values as a reference resource for future studies. Second, we review efforts to model tibiofemoral joint mechanical behaviour through FE modelling with particular focus on how studies have sourced tissue material properties. The last decade has seen a renaissance in material testing fuelled by development of a variety of new engineering techniques that allow the mechanical behaviour of both soft and hard tissues to be characterised at a spectrum of scales from nano- to bulk tissue level. As a result, there now exists an extremely broad range of published values for human tibiofemoral joint tissues. However, our systematic review highlights gaps and ambiguities that mean quantitative understanding of how tissue material properties alter with age and OA is limited. It is therefore currently challenging to construct FE models of the knee that are truly representative of a specific age or disease-state. Consequently, recent tibiofemoral joint FE models have been highly generic in terms of material properties even relying on non-human data from multiple species. We highlight this by critically evaluating current ability to quantitatively compare and model (1) young and old and (2) healthy and OA human tibiofemoral joints. We suggest that future research into both healthy and diseased knee function will benefit greatly from a subject- or cohort-specific approach in which FE models are constructed using material properties, medical imagery and loading data from cohorts with consistent demographics and/or disease states. PMID:29379690

Tissue material properties and computational modelling of the human tibiofemoral joint: a critical review.

PubMed

Peters, Abby E; Akhtar, Riaz; Comerford, Eithne J; Bates, Karl T

2018-01-01

Understanding how structural and functional alterations of individual tissues impact on whole-joint function is challenging, particularly in humans where direct invasive experimentation is difficult. Finite element (FE) computational models produce quantitative predictions of the mechanical and physiological behaviour of multiple tissues simultaneously, thereby providing a means to study changes that occur through healthy ageing and disease such as osteoarthritis (OA). As a result, significant research investment has been placed in developing such models of the human knee. Previous work has highlighted that model predictions are highly sensitive to the various inputs used to build them, particularly the mathematical definition of material properties of biological tissues. The goal of this systematic review is two-fold. First, we provide a comprehensive summation and evaluation of existing linear elastic material property data for human tibiofemoral joint tissues, tabulating numerical values as a reference resource for future studies. Second, we review efforts to model tibiofemoral joint mechanical behaviour through FE modelling with particular focus on how studies have sourced tissue material properties. The last decade has seen a renaissance in material testing fuelled by development of a variety of new engineering techniques that allow the mechanical behaviour of both soft and hard tissues to be characterised at a spectrum of scales from nano- to bulk tissue level. As a result, there now exists an extremely broad range of published values for human tibiofemoral joint tissues. However, our systematic review highlights gaps and ambiguities that mean quantitative understanding of how tissue material properties alter with age and OA is limited. It is therefore currently challenging to construct FE models of the knee that are truly representative of a specific age or disease-state. Consequently, recent tibiofemoral joint FE models have been highly generic in terms of material properties even relying on non-human data from multiple species. We highlight this by critically evaluating current ability to quantitatively compare and model (1) young and old and (2) healthy and OA human tibiofemoral joints. We suggest that future research into both healthy and diseased knee function will benefit greatly from a subject- or cohort-specific approach in which FE models are constructed using material properties, medical imagery and loading data from cohorts with consistent demographics and/or disease states.

Department of Energy Efforts to Promote Universal Adherence to the IAEA Additional Protocol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Killinger, Mark H.; Hansen, Linda H.; Kovacic, Don N.

2009-10-06

Entry-into-force of the U.S. Additional Protocol (AP) in January 2009 continues to demonstrate the ongoing commitment by the United States to promote universal adherence to the AP. The AP is a critical tool for improving the International Atomic Energy Agency’s (IAEA) capabilities to detect undeclared activities that indicate a clandestine nuclear weapons program. This is because States Parties are required to provide information about, and access to, nuclear fuel cycle activities beyond their traditional safeguards reporting requirements. As part of the U.S. AP Implementation Act and Senate Resolution of Ratification, the Administration is required to report annually to Congress onmore » measures taken to achieve the adoption of the AP in non-nuclear weapon states, as well as assistance to the IAEA to promote the effective implementation of APs in those states. A key U.S. effort in this area is being managed by the International Nuclear Safeguards and Engagement Program (INSEP) of the U.S. Department of Energy (DOE). Through new and existing bilateral cooperation agreements, INSEP has initiated technical assistance projects for AP implementation with selected non-weapon states. States with which INSEP is currently cooperating include Vietnam and Thailand, with Indonesia, Algeria, Morocco, and other countries as possible future collaborators in the area of AP implementation. The INSEP collaborative model begins with a joint assessment with our partners to identify specific needs they may have regarding entering the AP into force and any impediments to successful implementation. An action plan is then developed detailing and prioritizing the necessary joint activities. Such assistance may include: advice on developing legal frameworks and regulatory documents; workshops to promote understanding of AP requirements; training to determine possible declarable activities; assistance in developing a system to collect and submit declarations; performing industry outreach to raise awareness; guidance for reporting export and manufacturing of “especially designed or prepared” equipment listed in AP Annex I/Annex II; and lastly, developing indigenous capabilities to sustain AP implementation. INSEP also coordinates with the IAEA to ensure the harmonization of the assistance provided by DOE and the IAEA. This paper describes current efforts and future plans for AP international implementation support.« less

Joint federal research and development process to meet state and local needs. Part 1. Science and technology and political decision making

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wise, H F; Smith, L K; Einsweiler, R C

This part of the handbook addresses the basic how to do it - how states and local governments can identify complex and cross-cutting issues and develop and manage scientific and technical resources in seeking policy solutions to such issues. The following subjects are discussed: background statement of the issue; the research/decision-making process; defining problems and identifying research components; research and decision-making strategies; how to identify existing knowledge or ongoing research in the area of policy concern; and managing multi-disciplinary research. The fourteen agencies involved in this effort include: US Departments of Energy, Agriculture, Transportation, Housing and Urban Development, Environmental Protectionmore » Agency, and National Science Foundation. (PSB)« less

Technology Development Benefits and the Economics Breakdown Structure

NASA Technical Reports Server (NTRS)

Shaw, Eric J.

1998-01-01

This paper describes the construction and application of the EBS (Economics Breakdown Structure) in evaluating technology investments across multiple systems and organizations, illustrated with examples in space transportation technology. The United States Government (USG) has a long history of investing in technology to enable its missions. Agencies such as the National Aeronautics and Space Administration (NASA) and the Department of Defense (DoD) have evaluated their technology development programs primarily on their effects on mission performance and cost. More and more, though, USG agencies are being evaluated on their technology transfer to the commercial sector. In addition, an increasing number of USG missions are being accomplished by industry-led or joint efforts, where the USG provides technology and funding but tasks industry with development and operation of the mission systems.

Digital control for the condensate system in a combined cycle power plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanchez Parra, M.; Fuentes Gutierrez, J.E.; Castelo Cuevas, L.

1994-12-31

This paper presents the highlights by means of which development, installation and start up of the digital control system (DCS)for the condenser and hotwell (condensate system) were performed. This system belongs to the distributed control system installed by the Instituto de Investigaciones Electricas (IIE) at the Combined Cycle Power Plant in Gomez Palacio (GP), Durango, Mexico, during the February-March period, in 1993. The main steps for development of the condenser and hotwell control system include: process modeling, definition of control strategies, algorithms, design and software development, PC simulation tests, laboratory tests with an equipment similar to the one installed atmore » the GP Power Plant, installation, and finally, start up, which was a joint effort with the GP Power Plant engineering staff.« less

A computational framework for simultaneous estimation of muscle and joint contact forces and body motion using optimization and surrogate modeling.

PubMed

Eskinazi, Ilan; Fregly, Benjamin J

2018-04-01

Concurrent estimation of muscle activations, joint contact forces, and joint kinematics by means of gradient-based optimization of musculoskeletal models is hindered by computationally expensive and non-smooth joint contact and muscle wrapping algorithms. We present a framework that simultaneously speeds up computation and removes sources of non-smoothness from muscle force optimizations using a combination of parallelization and surrogate modeling, with special emphasis on a novel method for modeling joint contact as a surrogate model of a static analysis. The approach allows one to efficiently introduce elastic joint contact models within static and dynamic optimizations of human motion. We demonstrate the approach by performing two optimizations, one static and one dynamic, using a pelvis-leg musculoskeletal model undergoing a gait cycle. We observed convergence on the order of seconds for a static optimization time frame and on the order of minutes for an entire dynamic optimization. The presented framework may facilitate model-based efforts to predict how planned surgical or rehabilitation interventions will affect post-treatment joint and muscle function. Copyright © 2018 IPEM. Published by Elsevier Ltd. All rights reserved.

The Air Commander in the Solomon Islands Campaign: Unrivaled Unity of Effort in Joint Air Operations

DTIC Science & Technology

2011-06-01

aircraft, and people in the Pacific, keeping the Allies on the defensive throughout Asia and the Pacific. Singapore and the Philippines ... Philippines and Australia during the course of the war.16 Each of these commanders fell under the direct oversight of the American Joint Chiefs of Staff...Miller, The War in the Pacific, 81-85. August 11 revealing his newfound but tardy understanding of the problem: “This island warfare is a tough

Hearing on Education Funding and Budget Proposals for Federal Education Efforts. Joint Hearing before the Subcommittees on Postsecondary Education and Elementary, Secondary, and Vocational Education. of the Committee on Education and Labor. House of Representatives, One Hundred First Congress, First Session (Missoula, Montana, March 31, 1989).

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. House Committee on Education and Labor.

An examination of the fiscal year 1990 national educational budget and assessment of its potential impact on education in the northwestern United States, particularly in Montana and Washington, are contained in this joint hearing report. Statements, prepared statements, letters, and supplemental materials are presented on the following topics: the…

Biocatalyst Enhancement

EPA Science Inventory

The increasing availability of enzyme collections has assisted attempts by pharmaceutical producers to adopt green chemistry approaches to manufacturing. A joint effort between an enzyme producer and a pharmaceutical manufacturer has been enhanced over the past three years by ena...

49 CFR 37.141 - Requirements for a joint paratransit plan.

Code of Federal Regulations, 2010 CFR

2010-10-01

... INDIVIDUALS WITH DISABILITIES (ADA) Paratransit as a Complement to Fixed Route Service § 37.141 Requirements... effort: (1) A certification that the entity is committed to providing ADA paratransit service as part of...

Concise Review: Mesenchymal Stem Cells for Functional Cartilage Tissue Engineering: Taking Cues from Chondrocyte‐Based Constructs

PubMed Central

Tan, Andrea R.

2017-01-01

Abstract Osteoarthritis, the most prevalent form of joint disease, afflicts 9% of the U.S. population over the age of 30 and costs the economy nearly $100 billion annually in healthcare and socioeconomic costs. It is characterized by joint pain and dysfunction, though the pathophysiology remains largely unknown. Due to its avascular nature and limited cellularity, articular cartilage exhibits a poor intrinsic healing response following injury. As such, significant research efforts are aimed at producing engineered cartilage as a cell‐based approach for articular cartilage repair. However, the knee joint is mechanically demanding, and during injury, also a milieu of harsh inflammatory agents. The unforgiving mechano‐chemical environment requires tissue replacements that are capable of bearing such burdens. The use of mesenchymal stem cells (MSCs) for cartilage tissue engineering has emerged as a promising cell source due to their ease of isolation, capacity to readily expand in culture, and ability to undergo lineage‐specific differentiation into chondrocytes. However, to date, very few studies utilizing MSCs have successfully recapitulated the structural and functional properties of native cartilage, exposing the difficult process of uniformly differentiating stem cells into desired cell fates and maintaining the phenotype during in vitro culture and after in vivo implantation. To address these shortcomings, here, we present a concise review on modulating stem cell behavior, tissue development and function using well‐developed techniques from chondrocyte‐based cartilage tissue engineering. Stem Cells Translational Medicine 2017;6:1295–1303 PMID:28177194

DEVELOPMENT, INSTALLATION AND OPERATION OF THE MPC&A OPERATIONS MONITORING (MOM) SYSTEM AT THE JOINT INSTITUTE FOR NUCLEAR RESEARCH (JINR) DUBNA, RUSSIA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kartashov,V.V.; Pratt,W.; Romanov, Y.A.

The Material Protection, Control and Accounting (MPC&A) Operations Monitoring (MOM) systems handling at the International Intergovernmental Organization - Joint Institute for Nuclear Research (JINR) is described in this paper. Category I nuclear material (plutonium and uranium) is used in JINR research reactors, facilities and for scientific and research activities. A monitoring system (MOM) was installed at JINR in April 2003. The system design was based on a vulnerability analysis, which took into account the specifics of the Institute. The design and installation of the MOM system was a collaborative effort between JINR, Brookhaven National Laboratory (BNL) and the U.S. Departmentmore » of Energy (DOE). Financial support was provided by DOE through BNL. The installed MOM system provides facility management with additional assurance that operations involving nuclear material (NM) are correctly followed by the facility personnel. The MOM system also provides additional confidence that the MPC&A systems continue to perform effectively.« less

Solution Concepts for Distributed Decision-Making without Coordination

NASA Technical Reports Server (NTRS)

Beling, Peter A.; Patek, Stephen D.

2005-01-01

Consider a single-stage problem in which we have a group N agents who are attempting to minimize the expected cost of their joint actions, without the benefit of communication or a pre-established protocol but with complete knowledge of the expected cost of any joint set of actions for the group. We call this situation a static coordination problem. The central issue in defining an appropriate solution concept for static coordination problems is considering how to deal with the fact that if the agents axe faced with a set of multiple (mixed) strategies that are equally attractive in terms of cost, a failure of coordination may lead to an expected cost value that is worse than that of any of the strategies in the set. In this proposal, we describe the notion of a general coordination problem, describe initial efforts at developing a solution concept for static coordination problems, and then outline a research agenda that centers on activities that will be basis for obtaining a complete understanding of solutions to static coordination problems.

Around Marshall

NASA Image and Video Library

1999-09-12

The science laboratory, Spacelab-J (SL-J), flown aboard the STS-47 flight was a joint venture between NASA and the National Space Development Agency of Japan (NASDA) utilizing a manned Spacelab module. The mission conducted 24 materials science and 20 life science experiments, of which 35 were sponsored by NASDA, 7 by NASA, and two collaborative efforts. Materials science investigations covered such fields as biotechnology, electronic materials, fluid dynamics and transport phenomena, glasses and ceramics, metals and alloys, and acceleration measurements. Life sciences included experiments on human health, cell separation and biology, developmental biology, animal and human physiology and behavior, space radiation, and biological rhythms. Test subjects included the crew, Japanese koi fish (carp), cultured animal and plant cells, chicken embryos, fruit flies, fungi and plant seeds, and frogs and frog eggs. Featured together in joint ground activities during the SL-J mission are NASA/NASDA personnel at the Huntsville Operations Support Center (HOSC) Spacelab Payload Operations Control Center (SL POCC) at Marshall Space Flight Center (MSFC).

Around Marshall

NASA Image and Video Library

1992-09-12

The science laboratory, Spacelab-J (SL-J), flown aboard the STS-47 flight was a joint venture between NASA and the National Space Development Agency of Japan (NASDA) utilizing a manned Spacelab module. The mission conducted 24 materials science and 20 life science experiments, of which 35 were sponsored by NASDA, 7 by NASA, and two collaborative efforts. Materials science investigations covered such fields as biotechnology, electronic materials, fluid dynamics and transport phenomena, glasses and ceramics, metals and alloys, and acceleration measurements. Life sciences included experiments on human health, cell separation and biology, developmental biology, animal and human physiology and behavior, space radiation, and biological rhythms. Test subjects included the crew, Japanese koi fish (carp), cultured animal and plant cells, chicken embryos, fruit flies, fungi and plant seeds, and frogs and frog eggs. Featured together in the Science Operation Area (SOA) are payload specialists’ first Materials Processing Test during NASA/NASDA joint ground activities at the Huntsville Operations Support Center (HOSC) Spacelab Payload Operations Control Center (SL POCC) at Marshall Space Flight Center (MSFC).

Around Marshall

NASA Image and Video Library

1992-09-12

The science laboratory, Spacelab-J (SL-J), flown aboard the STS-47 flight was a joint venture between NASA and the National Space Development Agency of Japan (NASDA) utilizing a manned Spacelab module. The mission conducted 24 materials science and 20 life science experiments, of which 35 were sponsored by NASDA, 7 by NASA, and two collaborative efforts. Materials science investigations covered such fields as biotechnology, electronic materials, fluid dynamics and transport phenomena, glasses and ceramics, metals and alloys, and acceleration measurements. Life sciences included experiments on human health, cell separation and biology, developmental biology, animal and human physiology and behavior, space radiation, and biological rhythms. Test subjects included the crew, Japanese koi fish (carp), cultured animal and plant cells, chicken embryos, fruit flies, fungi and plant seeds, and frogs and frog eggs. Featured together in the Science Operation Area (SOA) are payload specialists’ first Materials Processing Test during NASA/NASDA joint ground activities at the Huntsville Operations Support Center (HOSC) Spacelab Payload Operations Control Center (SL POCC) at Marshall Space Fight Center (MSFC).

A Successful Experiment in Collaboration: U.S. Science Agencies Forge Major Joint IPY Outreach Efforts

NASA Astrophysics Data System (ADS)

Cole, S.; Goldman, J.; West, P.

2008-12-01

The International Polar Year (IPY) provided U.S. agencies involved in polar research with a major outreach challenge: how to portray a unified view of the wealth of federal activity through a communications network dominated by agency-focused channels. To meet this challenge, 16 federal agencies joined together in an ongoing interagency working group, lead by the National Science Foundation's Office of Polar Programs, resulting in a series of successful media and public outreach endeavors. These included a unique interagency U.S. IPY web site (www.ipy.gov) that allowed participating agencies to independently upload relevant information every day; a major IPY kickoff event at the National Academies of Science; and a joint NASA/NSF/USGS televised press conference unveiling a new satellite map of Antarctica. Key to these successes was the interagency working group, which facilitated in-depth and sustained interaction between the agencies in coordinating development of outreach strategies both at the agency and federal level.

Strategic planning with multitype libraries in the community: a model with extra funding as the main goal.

PubMed Central

Gall, C F; Miller, E G

1997-01-01

Medical libraries are discovering that ongoing collaboration in fundraising with other types of community libraries is mutually beneficial. Such partnerships may lead to joint grants, increase library visibility and access to decision makers, allow participation in community information networks, and provide leverage in additional fundraising projects. These partnerships have the potential to raise the profile of libraries. The accompanying community recognition for the parent organization may create a positive image, draw patients to the health center, and position the library and institution for future success in fundraising. Within institutions, development officers may become allies, mentors, and beneficiaries of the medical librarian's efforts. For a planned approach to community outreach with extra funding as the major objective, busy medical library administrators need guidelines. Standard participative techniques were applied to strategic planning by Indianapolis libraries to help achieve successful community outreach and to write joint statements of mission, vision, goals, and objectives. PMID:9285125

Building model analysis applications with the Joint Universal Parameter IdenTification and Evaluation of Reliability (JUPITER) API

USGS Publications Warehouse

Banta, E.R.; Hill, M.C.; Poeter, E.; Doherty, J.E.; Babendreier, J.

2008-01-01

The open-source, public domain JUPITER (Joint Universal Parameter IdenTification and Evaluation of Reliability) API (Application Programming Interface) provides conventions and Fortran-90 modules to develop applications (computer programs) for analyzing process models. The input and output conventions allow application users to access various applications and the analysis methods they embody with a minimum of time and effort. Process models simulate, for example, physical, chemical, and (or) biological systems of interest using phenomenological, theoretical, or heuristic approaches. The types of model analyses supported by the JUPITER API include, but are not limited to, sensitivity analysis, data needs assessment, calibration, uncertainty analysis, model discrimination, and optimization. The advantages provided by the JUPITER API for users and programmers allow for rapid programming and testing of new ideas. Application-specific coding can be in languages other than the Fortran-90 of the API. This article briefly describes the capabilities and utility of the JUPITER API, lists existing applications, and uses UCODE_2005 as an example.

A simple approach to the joint inversion of seismic body and surface waves applied to the southwest U.S.

NASA Astrophysics Data System (ADS)

West, Michael; Gao, Wei; Grand, Stephen

2004-08-01

Body and surface wave tomography have complementary strengths when applied to regional-scale studies of the upper mantle. We present a straight-forward technique for their joint inversion which hinges on treating surface waves as horizontally-propagating rays with deep sensitivity kernels. This formulation allows surface wave phase or group measurements to be integrated directly into existing body wave tomography inversions with modest effort. We apply the joint inversion to a synthetic case and to data from the RISTRA project in the southwest U.S. The data variance reductions demonstrate that the joint inversion produces a better fit to the combined dataset, not merely a compromise. For large arrays, this method offers an improvement over augmenting body wave tomography with a one-dimensional model. The joint inversion combines the absolute velocity of a surface wave model with the high resolution afforded by body waves-both qualities that are required to understand regional-scale mantle phenomena.

Ultrasound-Guided Steroid Injection of the Pisotriquetral Joint: A Multidisciplinary Effort.

PubMed

Brose, Steven W; Montfort, Janel; Gustafson, Kenneth J; Mittebrun, Ionica; Gauriloff, Samantha; Mosher, Mary; Bourbeau, Dennis J

2017-12-01

From the perspective of a multidisciplinary team, the authors describe the first reported use of ultrasound guidance for steroid injection into the pisotriquetral joint to relieve wrist pain of a person with spinal cord injury undergoing acute inpatient rehabilitation. Musculoskeletal ultrasound guidance was used to improve the accuracy of a corticosteroid injection of the pisotriquetral joint and the basal thumb in a 70-year-old man with paraplegia experiencing multifocal degenerative wrist pain. There was no bleeding or bruising after the injections, and the patient reported complete pain resolution 1 wk after the injections, which continued for over 1 yr. A multidisciplinary team was key in diagnosis, selection of treatment, and evaluation of treatment effect. Corticosteroid injection of the pisotriquetral joint under ultrasound guidance can be used as a treatment modality for managing wrist pain stemming from that joint. Further investigation and studies evaluating the use of ultrasound versus other imaging modalities for injection of the wrist are indicated.

Guilt and Effortful Control: Two Mechanisms that Prevent Disruptive Developmental Trajectories

PubMed Central

Kochanska, Grazyna; Barry, Robin A.; Jimenez, Natasha B.; Hollatz, Amanda L.; Woodard, Jarilyn

2009-01-01

Children's guilt associated with transgressions and their capacity for effortful control are both powerful forces that inhibit disruptive conduct. We examined how guilt and effortful control, repeatedly observed from toddler to preschool age, jointly predict children's disruptive outcomes in two multi-method multi-trait longitudinal studies (N's 57 and 99). Disruptive outcomes were rated by mothers at 73 months (Study 1) and mothers, fathers, and teachers at 52 and 67 months (Study 2). In both studies, guilt moderated effects of effortful control: For highly guilt-prone children, variations in effortful control were unrelated to future disruptive outcomes, but for children who were less guilt prone, effortful control predicted such outcomes. Guilt may inhibit transgressions through an automatic response due to negative arousal triggered by memories of past wrongdoing, regardless of child capacity for deliberate inhibition. Effortful control that engages a deliberate restraint may offset risk for disruptive conduct conferred by low guilt. PMID:19634978

Assembly considerations for large reflectors

NASA Technical Reports Server (NTRS)

Bush, H.

1988-01-01

The technologies developed at LaRC in the area of erectable instructures are discussed. The information is of direct value to the Large Deployable Reflector (LDR) because an option for the LDR backup structure is to assemble it in space. The efforts in this area, which include development of joints, underwater assembly simulation tests, flight assembly/disassembly tests, and fabrication of 5-meter trusses, led to the use of the LaRC concept as the baseline configuration for the Space Station Structure. The Space Station joint is linear in the load and displacement range of interest to Space Station; the ability to manually assemble and disassemble a 45-foot truss structure was demonstrated by astronauts in space as part of the ACCESS Shuttle Flight Experiment. The structure was built in 26 minutes 46 seconds, and involved a total of 500 manipulations of untethered hardware. Also, the correlation of the space experience with the neutral buoyancy simulation was very good. Sections of the proposed 5-meter bay Space Station truss have been built on the ground. Activities at LaRC have included the development of mobile remote manipulator systems (which can traverse the Space Station 5-meter structure), preliminary LDR sun shield concepts, LDR construction scenarios, and activities in robotic assembly of truss-type structures.

Research Initiatives and Preliminary Results In Automation Design In Airspace Management in Free Flight

NASA Technical Reports Server (NTRS)

Corker, Kevin; Lebacqz, J. Victor (Technical Monitor)

1997-01-01

The NASA and the FAA have entered into a joint venture to explore, define, design and implement a new airspace management operating concept. The fundamental premise of that concept is that technologies and procedures need to be developed for flight deck and ground operations to improve the efficiency, the predictability, the flexibility and the safety of airspace management and operations. To that end NASA Ames has undertaken an initial development and exploration of "key concepts" in the free flight airspace management technology development. Human Factors issues in automation aiding design, coupled aiding systems between air and ground, communication protocols in distributed decision making, and analytic techniques for definition of concepts of airspace density and operator cognitive load have been undertaken. This paper reports the progress of these efforts, which are not intended to definitively solve the many evolving issues of design for future ATM systems, but to provide preliminary results to chart the parameters of performance and the topology of the analytic effort required. The preliminary research in provision of cockpit display of traffic information, dynamic density definition, distributed decision making, situation awareness models and human performance models is discussed as they focus on the theme of "design requirements".

Ultrasonic Imaging Technology Helps American Manufacturer of Nondestructive Evaluation Equipment Become More Competitive in the Global Market

NASA Technical Reports Server (NTRS)

1995-01-01

Sonix, Inc., of Springfield, Virginia, has implemented ultrasonic imaging methods developed at the NASA Lewis Research Center. These methods have heretofore been unavailable on commercial ultrasonic imaging systems and provide significantly more sensitive material characterization than conventional high-resolution ultrasonic c-scanning. The technology transfer is being implemented under a cooperative agreement between NASA and Sonix, and several invention disclosures have been submitted by Dr. Roth to protect Lewis interests. Sonix has developed ultrasonic imaging systems used worldwide for microelectronics, materials research, and commercial nondestructive evaluation (NDE). In 1993, Sonix won the U.S. Department of Commerce "Excellence in Exporting" award. Lewis chose to work with Sonix for two main reasons: (1) Sonix is an innovative leader in ultrasonic imaging systems, and (2) Sonix was willing to apply the improvements we developed with our in-house Sonix equipment. This symbiotic joint effort has produced mutual benefits. Sonix recognized the market potential of our new and highly sensitive methods for ultrasonic assessment of material quality. We, in turn, see the cooperative effort as an effective means for transferring our technology while helping to improve the product of a domestic firm.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Standardization of grant and contract awardee names has been an area of concern since the development of the Department`s Procurement and Assistance Data System (PADS). A joint effort was begun in 1983 by the Office of Scientific and Technical Information (OSTI) and the Office of Procurement and Assistance Management/Information Systems and Analysis Division to develop a means for providing uniformity of awardee names. As a result of this effort, a method of assigning vendor identification codes to each unique awardee name, division, city, and state combination was developed and is maintained by OSTI. Changes to vendor identification codes or awardeemore » names contained in PADS can be made only by OSTI. Awardee names in the Directory indicate that the awardee has had a prime contract (excluding purchase orders of $10,000 or less) with, or a financial assistance award from, the Department. Award status--active, inactive, or retired--is not shown. The Directory is in alphabetic sequence based on awardee name and reflects the OSTI-assigned vendor identification code to the right of the name. A vendor identification code is assigned to each unique awardee name, division, city, and state (for place of performance). The same vendor identification code is used for awards throughout the Department.« less

A beamline systems model for Accelerator-Driven Transmutation Technology (ADTT) facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, A.M.M.; Paulson, C.C.; Peacock, M.A.

1995-10-01

A beamline systems code, that is being developed for Accelerator-Driven Transmutation Technology (ADTT) facility trade studies, is described. The overall program is a joint Grumman, G.H. Gillespie Associates (GHGA) and Los Alamos National Laboratory effort. The GHGA Accelerator Systems Model (ASM) has been adopted as the framework on which this effort is based. Relevant accelerator and beam transport models from earlier Grumman systems codes are being adapted to this framework. Preliminary physics and engineering models for each ADTT beamline component have been constructed. Examples noted include a Bridge Coupled Drift Tube Linac (BCDTL) and the accelerator thermal system. A decisionmore » has been made to confine the ASM framework principally to beamline modeling, while detailed target/blanket, balance-of-plant and facility costing analysis will be performed externally. An interfacing external balance-of-plant and facility costing model, which will permit the performance of iterative facility trade studies, is under separate development. An ABC (Accelerator Based Conversion) example is used to highlight the present models and capabilities.« less

A beamline systems model for Accelerator-Driven Transmutation Technology (ADTT) facilities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Todd, Alan M. M.; Paulson, C. C.; Peacock, M. A.

1995-09-15

A beamline systems code, that is being developed for Accelerator-Driven Transmutation Technology (ADTT) facility trade studies, is described. The overall program is a joint Grumman, G. H. Gillespie Associates (GHGA) and Los Alamos National Laboratory effort. The GHGA Accelerator Systems Model (ASM) has been adopted as the framework on which this effort is based. Relevant accelerator and beam transport models from earlier Grumman systems codes are being adapted to this framework. Preliminary physics and engineering models for each ADTT beamline component have been constructed. Examples noted include a Bridge Coupled Drift Tube Linac (BCDTL) and the accelerator thermal system. Amore » decision has been made to confine the ASM framework principally to beamline modeling, while detailed target/blanket, balance-of-plant and facility costing analysis will be performed externally. An interfacing external balance-of-plant and facility costing model, which will permit the performance of iterative facility trade studies, is under separate development. An ABC (Accelerator Based Conversion) example is used to highlight the present models and capabilities.« less

Astronomy in Cuba: practice and trends. An effort to develop a non-formal education programme

NASA Astrophysics Data System (ADS)

Pomares, Oscar A.

In the recent past years, a daily stronger movement of non-professional astronomers has become the center of development for astronomy, a subject of study practically absent now from the national education system in Cuba. A key roll in this movement has been played by the professional staff of the Department of Astronomy of the Institute of Geophysics and Astronomy. As direct outcome of this joint effort between astronomers and amateurs is the research on meteors and comets, presented in two national and one international scientific meeetings. The opening last year of the "Palacio de las Ciencias" in the main building of the country, "El Capitolio Nacional", the participation in conferences and workshops of professional astronomers facing the general public, and their participation in prime-time TV and radio programs open a way for the growth of astronomical knowledge among the Cuban people. Two national meeetings gathering together professional and non- professional astronomers have been held already. Future works in the NEOs international campaign are foreseen. Practice and trends of astronomy in Cuba clarify views of our future in the oldest natural science.

Using satellite microwave sensors to develop climate data records

NASA Astrophysics Data System (ADS)

Ferraro, Ralph; Meng, Huan; Luo, Zhengzhao

2011-08-01

NOAA Workshop on Climate Data Records From Satellite Passive Microwave Sounders: AMSU/MHS/SSMT2; College Park, Maryland, 2-3 March 2011 ; The National Oceanic and Atmospheric Administration's (NOAA) Climate Data Record (CDR) program (http://www.ncdc.noaa.gov/cdr/index.html) is an effort to create long-term homogeneous records of satellite measurements and derived products. As part of this effort, scientists at two related projects that focus on passive microwave sensors with the goal of hydrological applications—one led by a National Environmental Satellite, Data, and Information Service/Center for Satellite Applications and Research (STAR) team and one led by the City College of New York (CCNY)—held a joint workshop with the following objectives: To allow the CDR teams to interact with satellite data and product users and other CDR developers on relevant aspects of sensor characteristics and intercalibration that will lead to mature CDRs; To provide a formal mechanism for input by subject matter experts, in particular, sensor scientists and engineers; and> To move toward a community consensus approach for NOAA microwave sounder CDRs.

Signaling networks in joint development

PubMed Central

Salva, Joanna E.; Merrill, Amy E.

2016-01-01

Here we review studies identifying regulatory networks responsible for synovial, cartilaginous, and fibrous joint development. Synovial joints, characterized by the fluid-filled synovial space between the bones, are found in high-mobility regions and are the most common type of joint. Cartilaginous joints unite adjacent bones through either a hyaline cartilage or fibrocartilage intermediate. Fibrous joints, which include the cranial sutures, form a direct union between bones through fibrous connective tissue. We describe how the distinct morphologic and histogenic characteristics of these joint classes are established during embryonic development. Collectively, these studies reveal that despite the heterogeneity of joint strength and mobility, joint development throughout the skeleton utilizes common signaling networks via long-range morphogen gradients and direct cell-cell contact. This suggests that different joint types represent specialized variants of homologous developmental modules. Identifying the unifying aspects of the signaling networks between joint classes allows a more complete understanding of the signaling code for joint formation, which is critical to improving strategies for joint regeneration and repair. PMID:27859991

Accounting for tagging-to-harvest mortality in a Brownie tag-recovery model by incorporating radio-telemetry data.

PubMed

Buderman, Frances E; Diefenbach, Duane R; Casalena, Mary Jo; Rosenberry, Christopher S; Wallingford, Bret D

2014-04-01

The Brownie tag-recovery model is useful for estimating harvest rates but assumes all tagged individuals survive to the first hunting season; otherwise, mortality between time of tagging and the hunting season will cause the Brownie estimator to be negatively biased. Alternatively, fitting animals with radio transmitters can be used to accurately estimate harvest rate but may be more costly. We developed a joint model to estimate harvest and annual survival rates that combines known-fate data from animals fitted with transmitters to estimate the probability of surviving the period from capture to the first hunting season, and data from reward-tagged animals in a Brownie tag-recovery model. We evaluated bias and precision of the joint estimator, and how to optimally allocate effort between animals fitted with radio transmitters and inexpensive ear tags or leg bands. Tagging-to-harvest survival rates from >20 individuals with radio transmitters combined with 50-100 reward tags resulted in an unbiased and precise estimator of harvest rates. In addition, the joint model can test whether transmitters affect an individual's probability of being harvested. We illustrate application of the model using data from wild turkey, Meleagris gallapavo, to estimate harvest rates, and data from white-tailed deer, Odocoileus virginianus, to evaluate whether the presence of a visible radio transmitter is related to the probability of a deer being harvested. The joint known-fate tag-recovery model eliminates the requirement to capture and mark animals immediately prior to the hunting season to obtain accurate and precise estimates of harvest rate. In addition, the joint model can assess whether marking animals with radio transmitters affects the individual's probability of being harvested, caused by hunter selectivity or changes in a marked animal's behavior.

Accounting for tagging-to-harvest mortality in a Brownie tag-recovery model by incorporating radio-telemetry data

USGS Publications Warehouse

Buderman, Frances E.; Diefenbach, Duane R.; Casalena, Mary Jo; Rosenberry, Christopher S.; Wallingford, Bret D.

2014-01-01

The Brownie tag-recovery model is useful for estimating harvest rates but assumes all tagged individuals survive to the first hunting season; otherwise, mortality between time of tagging and the hunting season will cause the Brownie estimator to be negatively biased. Alternatively, fitting animals with radio transmitters can be used to accurately estimate harvest rate but may be more costly. We developed a joint model to estimate harvest and annual survival rates that combines known-fate data from animals fitted with transmitters to estimate the probability of surviving the period from capture to the first hunting season, and data from reward-tagged animals in a Brownie tag-recovery model. We evaluated bias and precision of the joint estimator, and how to optimally allocate effort between animals fitted with radio transmitters and inexpensive ear tags or leg bands. Tagging-to-harvest survival rates from >20 individuals with radio transmitters combined with 50–100 reward tags resulted in an unbiased and precise estimator of harvest rates. In addition, the joint model can test whether transmitters affect an individual's probability of being harvested. We illustrate application of the model using data from wild turkey, Meleagris gallapavo,to estimate harvest rates, and data from white-tailed deer, Odocoileus virginianus, to evaluate whether the presence of a visible radio transmitter is related to the probability of a deer being harvested. The joint known-fate tag-recovery model eliminates the requirement to capture and mark animals immediately prior to the hunting season to obtain accurate and precise estimates of harvest rate. In addition, the joint model can assess whether marking animals with radio transmitters affects the individual's probability of being harvested, caused by hunter selectivity or changes in a marked animal's behavior.

NASA Earth Science Partnerships - The Role and Value of Commercial and Non-Profit Partnerships with Government in the Earth Sciences

NASA Astrophysics Data System (ADS)

Favors, J.; Cauffman, S.; Ianson, E.; Kaye, J. A.; Friedl, L.; Green, D. S.; Lee, T. J.; Murphy, K. J.; Turner, W.

2017-12-01

NASA's Earth Science Division (ESD) seeks to develop a scientific understanding of the Earth as a dynamic, integrated system of diverse components that interact in complex ways - analogous to the human body. The Division approaches this goal through a coordinated series of satellite and airborne missions, sponsored basic and applied research, and technology development. Integral to this approach are strong collaborations and partnerships with a spectrum of organizations with technical and non-technical expertise. This presentation will focus on a new commercial and non-profit partnership effort being undertaken by ESD to integrate expertise unique to these sectors with expertise at NASA to jointly achieve what neither group could alone. Highlights will include case study examples of joint work with perspectives from both NASA and the partner, building interdisciplinary teams with diverse backgrounds but common goals (e.g., economics and Earth observations for valuing natural capital), partnership successes and challenges in the co-production of science and applications, utilizing partner networks to amplify project outcomes, and how involving partners in defining the project scope drives novel and unique scientific and decision-making questions to arise.

Multisatellite constellation configuration selection for multiregional highly elliptical orbit constellations

NASA Technical Reports Server (NTRS)

Matossian, Mark G.

1994-01-01

The Archimedes Project is a joint effort of the European Space Agency (ESA) and the National Space Development Agency of Japan (NASDA). The primary goal of the Archimedes project is to perform a technical feasibility analysis and preliminary design of a highly inclined multisatellite constellation for direct broadcast and mobile communications services for Europe, Japan and much of North America. This report addresses one aspect of this project, specifically an analysis of continuous satellite coverage using multiregional highly elliptical orbits (M-HEO's). The analysis methodology and ensuing software tool, named SPIFF, were developed specifically for this project by the author during the summer of 1992 under the STA/NSF Summer Institute in Japan Program at Tsukuba Space Center.

Indigenous Manufacturing realization of TWIN Source

NASA Astrophysics Data System (ADS)

Pandey, R.; Bandyopadhyay, M.; Parmar, D.; Yadav, R.; Tyagi, H.; Soni, J.; Shishangiya, H.; Sudhir Kumar, D.; Shah, S.; Bansal, G.; Pandya, K.; Parmar, K.; Vuppugalla, M.; Gahlaut, A.; Chakraborty, A.

2017-04-01

TWIN source is two RF driver based negative ion source that has been planned to bridge the gap between single driver based ROBIN source (currently operational) and eight river based DNB source (to be operated under IN-TF test facility). TWIN source experiments have been planned at IPR keeping the objective of long term domestic fusion programme to gain operational experiences on vacuum immersed multi driver RF based negative ion source. High vacuum compatible components of twin source are designed at IPR keeping an aim on indigenous built in attempt. These components of TWIN source are mainly stainless steel and OFC-Cu. Being high heat flux receiving components, one of the major functional requirements is continuous heat removal via water as cooling medium. Hence for the purpose stainless steel parts are provided with externally milled cooling lines and that shall be covered with a layer of OFC-cu which would be on the receiving side of high heat flux. Manufacturability of twin source components requires joining of these dissimilar materials via process like electrode position, electron beam welding and vacuum brazing. Any of these manufacturing processes shall give a vacuum tight joint having proper joint strength at operating temperature and pressure. Taking the indigenous development effort vacuum brazing (in non-nuclear environment) has been opted for joining of dissimilar materials of twin source being one of the most reliable joining techniques and commercially feasible across the suppliers of country. Manufacturing design improvisation for the components has been done to suit the vacuum brazing process requirement and to ease some of the machining without comprising over the functional and operational requirements. This paper illustrates the details on the indigenous development effort, design improvisation to suits manufacturability, vacuum brazing basics and its procedures for twin source components.

Theme II Joint Work Plan -2017 Collaboration and Knowledge Sharing on Large-scale Demonstration Projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xiaoliang; Stauffer, Philip H.

This effort is designed to expedite learnings from existing and planned large demonstration projects and their associated research through effective knowledge sharing among participants in the US and China.

Transit evacuation planning : two case studies.

DOT National Transportation Integrated Search

2010-06-01

This project addresses the emergency transit evacuation of individuals without personal vehicles or the : means to acquire them during extreme coastal events. It is a joint effort of the University Transportation : Center for Alabama (UTCA) and the C...

The Rigid Pavement Database: Overview and Data Collection Plan

DOT National Transportation Integrated Search

1998-06-01

The rigid pavement (RP) database contains historical distress data obtained from more than 400 continuously reinforced concrete pavements(CRCP) and jointed concrete pavements (JCP) across the state of Texas. Data collection efforts began in 1974 and ...

Architectural Design for the Global Legal Information Network

NASA Technical Reports Server (NTRS)

Kalpakis, Konstantinos

1999-01-01

In this report, we provide a summary of our activities regarding the goals, requirements analysis, design, and prototype implementation for the Global Legal Information Network, a joint effort between the Law Library of Congress and NASA.

Longitudinal study of ITS implementation : decision factors and effects.

DOT National Transportation Integrated Search

2013-04-01

The Intelligent Transportation Systems (ITS) Joint Program Office (JPO) is placing increasing emphasis on transferring ITS technology from research to deployment, and on accelerating the rate of ITS technology adoption. As part of these efforts, the ...

Smart campus transit laboratory for research and education.

DOT National Transportation Integrated Search

2011-12-31

A joint effort by the Ohio State University (OSU) Transportation and Parking Services, OSU College of Engineering, OSU Department of Civil and Environmental Engineering and Geodetic Science, and Clever Devices has recently succeeded in equipping the ...

Science and Technology Cooperation as an Effective Bridge for Strengthening Relations Between Russia and the US

NASA Astrophysics Data System (ADS)

Kislyak, Sergei

2017-01-01

In the conditions of spiraling tensions and curtailing of many platforms for the dialogue between Russia and the U.S. scientific cooperation could play a positive role. The history of our relations shows that joint effort by Russian and American scientists has repeatedly contributed to finding solutions in difficult situations, even during the ``cold war''. Thanks to the common efforts of the scientists of our countries hundreds of remarkable discoveries and significant achievements in such areas as physics, chemistry, space, medicine, etc. were made. Scientific community has no doubt that our bilateral scientific cooperation is in national interests of both nations. Although our joint work on a number of important issues is suspended today. The author is going to share his view with us on whether science and technology cooperation serve as an effective bridge for strengthening relations between Russia and the U.S.?

Air-sea interaction and remote sensing

NASA Technical Reports Server (NTRS)

Katsaros, Kristina B.; Ataktuerk, Serhad S.

1992-01-01

The first part of the proposed research was a joint effort between our group and the Applied Physics Laboratory (APL), University of Washington. Our own research goal is to investigate the relation between the air-sea exchange processes and the sea state over the open ocean and to compare these findings with our previous results obtained over a small body of water namely, Lake Washington. The goals of the APL researchers are to study (1) the infrared sea surface temperature (SST) signature of breaking waves and surface slicks, and (2) microwave and acoustic scattering from water surface. The task of our group in this joint effort is to conduct measurements of surface fluxes (of momentum, sensible heat, and water vapor) and atmospheric radiation (longwave and shortwave) to achieve our research goal as well as to provide crucial complementary data for the APL studies. The progress of the project is summarized.

A Maximum Muscle Strength Prediction Formula Using Theoretical Grade 3 Muscle Strength Value in Daniels et al.'s Manual Muscle Test, in Consideration of Age: An Investigation of Hip and Knee Joint Flexion and Extension.

PubMed

Usa, Hideyuki; Matsumura, Masashi; Ichikawa, Kazuna; Takei, Hitoshi

2017-01-01

This study attempted to develop a formula for predicting maximum muscle strength value for young, middle-aged, and elderly adults using theoretical Grade 3 muscle strength value (moment fair: M f )-the static muscular moment to support a limb segment against gravity-from the manual muscle test by Daniels et al. A total of 130 healthy Japanese individuals divided by age group performed isometric muscle contractions at maximum effort for various movements of hip joint flexion and extension and knee joint flexion and extension, and the accompanying resisting force was measured and maximum muscle strength value (moment max, M m ) was calculated. Body weight and limb segment length (thigh and lower leg length) were measured, and M f was calculated using anthropometric measures and theoretical calculation. There was a linear correlation between M f and M m in each of the four movement types in all groups, excepting knee flexion in elderly. However, the formula for predicting maximum muscle strength was not sufficiently compatible in middle-aged and elderly adults, suggesting that the formula obtained in this study is applicable in young adults only.

A Maximum Muscle Strength Prediction Formula Using Theoretical Grade 3 Muscle Strength Value in Daniels et al.'s Manual Muscle Test, in Consideration of Age: An Investigation of Hip and Knee Joint Flexion and Extension

PubMed Central

Matsumura, Masashi; Ichikawa, Kazuna; Takei, Hitoshi

2017-01-01

This study attempted to develop a formula for predicting maximum muscle strength value for young, middle-aged, and elderly adults using theoretical Grade 3 muscle strength value (moment fair: Mf)—the static muscular moment to support a limb segment against gravity—from the manual muscle test by Daniels et al. A total of 130 healthy Japanese individuals divided by age group performed isometric muscle contractions at maximum effort for various movements of hip joint flexion and extension and knee joint flexion and extension, and the accompanying resisting force was measured and maximum muscle strength value (moment max, Mm) was calculated. Body weight and limb segment length (thigh and lower leg length) were measured, and Mf was calculated using anthropometric measures and theoretical calculation. There was a linear correlation between Mf and Mm in each of the four movement types in all groups, excepting knee flexion in elderly. However, the formula for predicting maximum muscle strength was not sufficiently compatible in middle-aged and elderly adults, suggesting that the formula obtained in this study is applicable in young adults only. PMID:28133549

Development of a Bio-Equivalent Ultraviolet Dosimeter to Monitor the Capacity for Vitamin D Synthesis of Sunlight Final Report CRADA No. TC02086.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, C. F.; Wood, D.

This project represents a collaborative effort between Lawrence Livermore National Security, LLC as manager and operator of Lawrence Livermore National Laboratory (LLNL) and Rhyolite Technology Group, Inc. (Rhyolite) to develop concepts and designs for a consumer ultraviolet (UV) biodosimeter based on the human biochemistry of Vitamin D synthesis. Rhyolite was established to engage in product development, licensing and consulting for the manufacture and supply of new products worldwide. Rhyolite worked jointly with LLNL and the Kiev Institute of Physics (KIP) in Ukraine to leverage previously developed UV sensor technologies by extending the previous work into commercially viable products. The projectmore » consisted primarily of the scientific, engineering and business activities needed to develop the UV bio-dosimeter for applications that include health and industrial measurement of ultraviolet radiation.« less

Periprosthetic joint infection: are patients with multiple prosthetic joints at risk?

PubMed

Jafari, S Mehdi; Casper, David S; Restrepo, Camilo; Zmistowski, Benjamin; Parvizi, Javad; Sharkey, Peter F

2012-06-01

Patients who present with a periprosthetic joint infection in a single joint may have multiple prosthetic joints. The risk of these patients developing a subsequent infection in another prosthetic joint is unknown. Our purposes were (1) to identify the risk of developing a subsequent infection in another prosthetic joint and (2) to describe the time span and organism profile to the second prosthetic infection. We retrospectively identified 55 patients with periprosthetic joint infection who had another prosthetic joint in place at the time of presentation. Of the 55 patients, 11 (20%) developed a periprosthetic joint infection in a second joint. The type of organism was the same as the first infection in 4 (36%) of 11 patients. The time to developing a second infection averaged 2.0 years (range, 0-6.9 years). Copyright © 2012 Elsevier Inc. All rights reserved.

Evolution of Aerosol Research in India and the RAWEX–GVAX:An Overview

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krishna Moorthy, K.; Satheesh, S. K.; Kotamarthi, V. R.

Climate change has great significance in Asia in general, and India in particular; and atmospheric aerosols have a decisive role in this. The climate forcing potential of aerosols is closely linked to their optical, microphysical and chemical properties. Systematic efforts to characterize these properties over the Indian region started about 5 decades ago, and evolved over the years through concerted efforts in the form of long-term scientific programmes as well as concerted fields experiments. All these have resulted in this activity becoming one of the most vibrant fields of climate research in India and have brought several important issues inmore » the national and international foci. The field experiment, RAWEX-GVAX (Regional Aerosol Warming Experiment-Ganges Valley Aerosol Experiment), conducted during 2011-12 jointly by the US Department of Energy, Indian Space Research Organization and Department of Science and Technology, has emerged as a direct outcome of the above efforts. This overview provides a comprehensive account of the development of aerosol-climate research in India and south Asia, and the accomplishment and newer issues that warranted the above field campaign. Details of RAWEX-GVAX, the major outcomes and the subsequent and more recent efforts are presented, followed by the way forward in this field for the next several years to come.« less

US/German Collaboration in Salt Repository Research, Design and Operation - 13243

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steininger, Walter; Hansen, Frank; Biurrun, Enrique

2013-07-01

Recent developments in the US and Germany [1-3] have precipitated renewed efforts in salt repository investigations and related studies. Both the German rock salt repository activities and the US waste management programs currently face challenges that may adversely affect their respective current and future state-of-the-art core capabilities in rock salt repository science and technology. The research agenda being pursued by our respective countries leverages collective efforts for the benefit of both programs. The topics addressed by the US/German salt repository collaborations align well with the findings and recommendations summarized in the January 2012 US Blue Ribbon Commission on America's Nuclearmore » Future (BRC) report [4] and are consistent with the aspirations of the key topics of the Strategic Research Agenda of the Implementing Geological Disposal of Radioactive Waste Technology Platform (IGD-TP) [5]. Against this background, a revival of joint efforts in salt repository investigations after some years of hibernation has been undertaken to leverage collective efforts in salt repository research, design, operations, and related issues for the benefit of respective programs and to form a basis for providing an attractive, cost-effective insurance against the premature loss of virtually irreplaceable scientific expertise and institutional memory. (authors)« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henager, Charles H.; Kurtz, Richard J.; Canfield, Nathan L.

The use of SiC composites in fusion environments likely requires joining of plates using reactive joining or brazing. One promising reactive joining method uses solid-state displacement reactions between Si and TiC to produce Ti3SiC2 + SiC. We continue to explore the processing envelope for this joint for the TITAN collaboration in order to produce optimal joints to undergo irradiation studies in HFIR. One noted feature of the joints produced using tape-calendared powders of TiC+Si has been the large void regions that have been apparently unavoidable. Although the produced joints are very strong, these voids are undesirable. In addition, the tapesmore » that were made for this joining were produced about 20 years ago and were aging. Therefore, we embarked on an effort to produce some new tape cast powders of TiC and Si that could replace our aging tape calendared materials.« less

Lamb wave propagation in a restricted geometry composite pi-joint specimen

NASA Astrophysics Data System (ADS)

Blackshire, James L.; Soni, Som

2012-05-01

The propagation of elastic waves in a material can involve a number of complex physical phenomena, resulting in both subtle and dramatic effects on detected signal content. In recent years, the use of advanced methods for characterizing and imaging elastic wave propagation and scattering processes has increased, where for example the use of scanning laser vibrometry and advanced computational models have been used very effectively to identify propagating modes, scattering phenomena, and damage feature interactions. In the present effort, the propagation of Lamb waves within a narrow, constrained geometry composite pi-joint structure are studied using 3D finite element models and scanning laser vibrometry measurements, where the effects of varying sample thickness, complex joint curvatures, and restricted structure geometries are highlighted, and a direct comparison of computational and experimental results are provided for simulated and realistic geometry composite pi-joint samples.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henzlova, Daniela; Kouzes, R.; McElroy, R.

International safeguards inspectorates (e.g., International Atomic Energy Agency {IAEA}, or Euratom) rely heavily on neutron assay techniques, and in particular, on coincidence counters for the verification of declared nuclear materials under safeguards and for monitoring purposes. While 3He was readily available, the reliability, safety, ease of use, gamma-ray insensitivity, and high intrinsic thermal neutron detection efficiency of 3He-based detectors obviated the need for alternative detector technologies. However, the recent decline of the 3He gas supply has triggered international efforts to develop and field neutron detectors that make use of alternative materials. In response to this global effort, the U.S. Departmentmore » of Energy’s (DOE) National Nuclear Security Administration (NNSA) and Euratom launched a joint effort aimed at bringing together international experts, technology users and developers in the field of nuclear safeguards to discuss and evaluate the proposed 3He alternative materials and technologies. The effort involved a series of two workshops focused on detailed overviews and viability assessments of various 3He alternative technologies for use in nuclear safeguards applications. The key objective was to provide a platform for collaborative discussions and technical presentations organized in a compact, workshop-like format to stimulate interactions among the participants. The meetings culminated in a benchmark exercise providing a unique opportunity for the first inter-comparison of several available alternative technologies. This report provides an overview of the alternative technology efforts presented during the two workshops along with a summary of the benchmarking activities and results. The workshop recommendations and key consensus observations are discussed in the report, and used to outline a proposed path forward and future needs foreseeable in the area of 3He-alternative technologies.« less

NASA GRC UAS Project: Communications Modeling and Simulation Status

NASA Technical Reports Server (NTRS)

Kubat, Greg

2013-01-01

The integration of Unmanned Aircraft Systems (UAS) in the National Airspace represents new operational concepts required in civil aviation. These new concepts are evolving as the nation moves toward the Next Generation Air Transportation System (NextGen) under the leadership of the Joint Planning and Development Office (JPDO), and through ongoing work by the Federal Aviation Administration (FAA). The desire and ability to fly UAS in the National Air Space (NAS) in the near term has increased dramatically, and this multi-agency effort to develop and implement a national plan to successfully address the challenges of UAS access to the NAS in a safe and timely manner is well underway. As part of the effort to integrate UAS in the National Airspace, NASA Glenn Research Center is currently involved with providing research into Communications systems and Communication system operations in order to assist with developing requirements for this implementation. In order to provide data and information regarding communication systems performance that will be necessary, NASA GRC is tasked with developing and executing plans for simulations of candidate future UAS command and control communications, in line with architectures and communications technologies being developed and/or proposed by NASA and relevant aviation organizations (in particular, RTCA SC-203). The simulations and related analyses will provide insight into the ability of proposed communications technologies and system architectures to enable safe operation of UAS, meeting UAS in the NAS project goals (including performance requirements, scalability, and interoperability), and ultimately leading to a determination of the ability of NextGen communication systems to accommodate UAS. This presentation, compiled by the NASA GRC team, will provide a view of the overall planned simulation effort and objectives, a description of the simulation concept and status of the design and development that has occurred to date.

Health technology assessment of medical devices: What is different? An overview of three European projects.

PubMed

Schnell-Inderst, Petra; Mayer, Julia; Lauterberg, Jörg; Hunger, Theresa; Arvandi, Marjan; Conrads-Frank, Annette; Nachtnebel, Anna; Wild, Claudia; Siebert, Uwe

2015-01-01

With the growing use and importance of health technology assessment (HTA) in decision making during recent years, health technology assessors, decision makers and stakeholders are confronted with methodological challenges due to specific characteristics of health technologies (e. g., pharmaceuticals, diagnostic tests, screening programs), their developmental environment, and their regulation process. Being aware of the necessity to use HTA as a policy instrument for sustainable health care systems in a regulatory environment of decentralized Conformité Européenne (CE) marking, the European Union (EU) is increasingly supporting the development of methods for the assessment of medical devices (MD) on different levels: within the scope of European research projects and within joint assessment activities of the member states of the European network for Health Technology Assessment (EUnetHTA). First, this article describes three projects: MedtecHTA-Methods for Health Technology Assessment of Medical Devices, a European Perspective Work Package 3 (WP3), Comparative Effectiveness of Medical Devices led by the University for Health Sciences, Medical Informatics and Technology (UMIT). Second, we discuss the experiences of the Ludwig Boltzmann Institute Health Technology Assessment (LBI HTA) with the joint production of rapid assessments of medical devices by several European HTA agencies within EUnetHTA. Third, a brief outline is given of the framework of joint methodological guideline elaboration by the EUnetHTA partner organizations because a guideline for therapeutic MD is also being developed here. We will describe aims, methods and some preliminary results of MedtecHTA and EUnetHTA Joint Action 2 Work Package 5 Strand B (WP5B) applying the HTA Core Model for Rapid Assessment for national adaptation and reporting, and give an overview of the development process of methodological guidelines within WP 7 of EUnetHTA Joint Action 2. Based on a literature review in MedtecHTA WP3 incremental development, context dependency and the physical mode of action of MD were identified as those characteristics making therapeutic MD different from drugs with regard to evaluation methods. In addition, regulation does not stipulate clinical trials. These characteristics were also identified as challenges for the production of joint assessments of MD within the HTA network EUnetHTA. Furthermore, adequate timing of assessment production, the variety of involved manufacturers, the non-transparent regulation process of MD in Europe and the often poor evidence base pose a challenge to EUnetHTA assessors. As a consequence, processes and methods for the joint production of rapid assessments must be continuously adapted and improved. Research on HTA methods for the assessment of MD tries to provide tools to deal with rapidly developing devices during evidence generation, dependence of clinical effectiveness of MD on user experience and context factors. There are also tools to integrate evidence from different sources adjusting for different levels of validity, but these methods are not established and need high epidemiological and statistical expertise. A framework for deciding whether additional evidence is needed to reduce uncertainty regarding safety, clinical effectiveness and cost-effectiveness will be adapted to MD. The whole process of evidence generation before and after market access has to be considered to provide an environment for conclusive HTA recommendations informing health care decision making. In Joint Action 2, EUnetHTA develops transparent processes for the early dialogue with stakeholders and fosters dissemination of appropriate HTA methods. In the case of MD, there are special accumulated needs for such efforts. Copyright © 2015. Published by Elsevier GmbH.

Joint Chiefs of Staff > Directorates > J7 | Joint Force Development

Science.gov Websites

development: Doctrine, Education, Concept Development & Experimentation, Training, Exercises and Lessons Coalition Partners. Joint Education Develop policies governing officer and enlisted Joint Professional Military Education (JPME), and the National Defense University. Direct JPME educational advisory group and

Public key infrastructure for DOE security research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aiken, R.; Foster, I.; Johnston, W.E.

This document summarizes the Department of Energy`s Second Joint Energy Research/Defence Programs Security Research Workshop. The workshop, built on the results of the first Joint Workshop which reviewed security requirements represented in a range of mission-critical ER and DP applications, discussed commonalties and differences in ER/DP requirements and approaches, and identified an integrated common set of security research priorities. One significant conclusion of the first workshop was that progress in a broad spectrum of DOE-relevant security problems and applications could best be addressed through public-key cryptography based systems, and therefore depended upon the existence of a robust, broadly deployed public-keymore » infrastructure. Hence, public-key infrastructure ({open_quotes}PKI{close_quotes}) was adopted as a primary focus for the second workshop. The Second Joint Workshop covered a range of DOE security research and deployment efforts, as well as summaries of the state of the art in various areas relating to public-key technologies. Key findings were that a broad range of DOE applications can benefit from security architectures and technologies built on a robust, flexible, widely deployed public-key infrastructure; that there exists a collection of specific requirements for missing or undeveloped PKI functionality, together with a preliminary assessment of how these requirements can be met; that, while commercial developments can be expected to provide many relevant security technologies, there are important capabilities that commercial developments will not address, due to the unique scale, performance, diversity, distributed nature, and sensitivity of DOE applications; that DOE should encourage and support research activities intended to increase understanding of security technology requirements, and to develop critical components not forthcoming from other sources in a timely manner.« less

Joint Composable Object Model and LVC Methodology

NASA Technical Reports Server (NTRS)

Rheinsmith, Richard; Wallace, Jeffrey; Bizub, Warren; Ceranowicz, Andy; Cutts, Dannie; Powell, Edward T.; Gustavson, Paul; Lutz, Robert; McCloud, Terrell

2010-01-01

Within the Department of Defense, multiple architectures are created to serve and fulfill one or several specific service or mission related LVC training goals. Multiple Object Models exist across and within those architectures and it is there that those disparate object models are a major source of interoperability problems when developing and constructing the training scenarios. The two most commonly used architectures are; HLA and TENA, with DIS and CTIA following close behind in terms of the number of users. Although these multiple architectures can share and exchange data the underlying meta-models for runtime data exchange are quite different, requiring gateways/translators to bridge between the different object model representations; while the Department of Defense's use of gateways are generally effective in performing these functions, as the LVC environment increases so too does the cost and complexity of these gateways. Coupled with the wide range of different object models across the various user communities we increase the propensity for run time errors, increased programmer stop gap measures during coordinated exercises, or failure of the system as a whole due to unknown or unforeseen incompatibilities. The Joint Composable Object Model (JCOM) project was established under an M&S Steering Committee (MSSC)-sponsored effort with oversight and control placed under the Joint Forces Command J7 Advanced Concepts Program Directorate. The purpose of this paper is to address the initial and the current progress that has been made in the following areas; the Conceptual Model Development Format, the Common Object Model, the Architecture Neutral Data Exchange Model (ANDEM), and the association methodology to allow the re-use of multiple architecture object models and the development of the prototype persistent reusable library.

Public Port Finance Survey for FY 1998

DOT National Transportation Integrated Search

1999-12-01

The report is a joint effort of the American Association of Port Authorities and the Maritime Administration, U. S. Dept. of Transportation. It covers financial data on maritime activities at 70 U. S. and Canadian ports, including the income statemen...

Results of the 2008-09 Campus Travel Survey

DOT National Transportation Integrated Search

2009-09-24

The campus travel survey is a joint effort by the Transportation & Parking Services (TAPS) on campus and the Sustainable Transportation Center, part of the Institute of Transportation Studies at UC Davis, meant to be administered annually each fall b...

LANDSCAPE MANAGEMENT PRACTICES

EPA Science Inventory

USDA Conservation Practices are applied at various scales ranging from a portion of a field or a specific farm operation to the watershed or landscape scale. The Conservation Effects Assessment Project is a joint effort of USDA Conservation and Research agencies to determine the...

Large Scale Evaluation fo Nickel Aluminide Rolls

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

2005-09-01

This completed project was a joint effort between Oak Ridge National Laboratory and Bethlehem Steel (now Mittal Steel) to demonstrate the effectiveness of using nickel aluminide intermetallic alloy rolls as part of an updated, energy-efficient, commercial annealing furnace system.

Social task switching: On the automatic social engagement of executive functions.

PubMed

Dudarev, Veronica; Hassin, Ran R

2016-01-01

Humans are quintessentially social, yet much of cognitive psychology has focused on the individual, in individual settings. The literature on joint action is one of the most prominent exceptions. Joint-action research studies the sociality of our mental representations by examining how the tasks of other people around us affect our own task performance. In this paper we go beyond examining whether we represent others and their tasks, by asking whether we also automatically do their tasks with them, even if they require effortful executive functions. To this end we examine one of the core executive functions, shifting, in a new paradigm that allows us to investigate task-switching in a joint-action setup. Copyright © 2015 Elsevier B.V. All rights reserved.

An Automated, Low Mass, Low Power Drill for Acquiring Subsurface Samples of Ground Ice for Astrobiology Studies on Earth and on Mars

NASA Technical Reports Server (NTRS)

Briggs, G. A.; McKay, C.; George, J.; Derkowski, G.; Cooper, G.; Zacny, K.; Baker, R. Fincher; Pollard, W.; Clifford, S.

2003-01-01

As a project that is part of NASA s Astrobiology Technology & Instrument Development Program (ASTID), we are developing a low mass (approx.20kg) drill that will be operated without drilling fluids and at very low power levels (approx.60 watts electrical) to access and retrieve samples from permafrost regions of Earth and Mars. The drill, designed and built as a joint effort by NASA JSC and Baker-Hughes International, takes the form of a down-hole unit attached to a cable so that it can, in principle, be scaled easily to reach significant depths. A parallel laboratory effort is being carried out at UC Berkeley to characterize the physics of dry drilling under martian conditions of pressure, temperature and atmospheric composition. Data from the UCB and JSC laboratory experiments are being used as input to a drill simulation program which is under development to provide autonomous control of the drill. The first Arctic field test of the unit is planned for May 2004. A field expedition to Eureka on Ellesmere Island in Spring 2003 provided an introduction for several team members to the practical aspects of drilling under Arctic conditions. The field effort was organized by Wayne Pollard of McGill University and Christopher McKay of NASA ARC. A conventional science drill provided by New Zealand colleagues was used to recover ground ice cores for analysis of their microbial content and also to develop techniques using tracers to track the depth of penetration of contamination from the core surface into the interior of the samples.

The development of a UGV-mounted automated refueling system for VTOL UAVs

NASA Astrophysics Data System (ADS)

Wills, Mike; Burmeister, Aaron; Nelson, Travis; Denewiler, Thomas; Mullens, Kathy

2006-05-01

This paper describes the latest efforts to develop an Automated UAV Mission System (AUMS) for small vertical takeoff and landing (VTOL) unmanned air vehicles (UAVs). In certain applications such as force protection, perimeter security, and urban surveillance a VTOL UAV can provide far greater utility than fixed-wing UAVs or ground-based sensors. The VTOL UAV can operate much closer to an object of interest and can provide a hover-and-stare capability to keep its sensors trained on an object, while the fixed wing UAV would be forced into a higher altitude loitering pattern where its sensors would be subject to intermittent blockage by obstacles and terrain. The most significant disadvantage of a VTOL UAV when compared to a fixed-wing UAV is its reduced flight endurance. AUMS addresses this disadvantage by providing forward staging, refueling, and recovery capabilities for the VTOL UAV through a host unmanned ground vehicle (UGV), which serves as a launch/recovery platform and service station. The UGV has sufficient payload capacity to carry UAV fuel for multiple launch, recovery, and refuel iterations. The UGV also provides a highly mobile means of forward deploying a small UAV into hazardous areas unsafe for personnel, such as chemically or biologically contaminated areas. Teaming small UAVs with large UGVs can decrease risk to personnel and expand mission capabilities and effectiveness. There are numerous technical challenges being addressed by these development efforts. Among the challenges is the development and integration of a precision landing system compact and light enough to allow it to be mounted on a small VTOL UAV while providing repeatable landing accuracy to safely land on the AUMS. Another challenge is the design of a UGV-transportable, expandable, self-centering landing pad that contains hardware and safety devices for automatically refueling the UAV. A third challenge is making the design flexible enough to accommodate different types of VTOL UAVs, such as the AAI iSTAR ducted-fan vehicle and small helicopter UAVs. Finally, a common command-and-control architecture which supports the UAV, UGV, and AUMS must be developed and interfaced with these systems to allow fully autonomous collaborative behaviors. Funded by the Joint Robotics Program, AUMS is part of a joint effort with the Air Force Research Laboratory and the Army Missile Research Development and Engineering Command. The objective is to develop and demonstrate UGVUAV teaming concepts and work with the warfighter to ensure that future upgrades are focused on operational requirements. This paper describes the latest achievements in AUMS development and some of the military program and first responder situations that could benefit from this system.

Single-edition quadrangle maps

USGS Publications Warehouse

,

1998-01-01

In August 1993, the U.S. Geological Survey's (USGS) National Mapping Division and the U.S. Department of Agriculture's Forest Service signed an Interagency Agreement to begin a single-edition joint mapping program. This agreement established the coordination for producing and maintaining single-edition primary series topographic maps for quadrangles containing National Forest System lands. The joint mapping program saves money by eliminating duplication of effort by the agencies and results in a more frequent revision cycle for quadrangles containing national forests. Maps are revised on the basis of jointly developed standards and contain normal features mapped by the USGS, as well as additional features required for efficient management of National Forest System lands. Single-edition maps look slightly different but meet the content, accuracy, and quality criteria of other USGS products. The Forest Service is responsible for the land management of more than 191 million acres of land throughout the continental United States, Alaska, and Puerto Rico, including 155 national forests and 20 national grasslands. These areas make up the National Forest System lands and comprise more than 10,600 of the 56,000 primary series 7.5-minute quadrangle maps (15-minute in Alaska) covering the United States. The Forest Service has assumed responsibility for maintaining these maps, and the USGS remains responsible for printing and distributing them. Before the agreement, both agencies published similar maps of the same areas. The maps were used for different purposes, but had comparable types of features that were revised at different times. Now, the two products have been combined into one so that the revision cycle is stabilized and only one agency revises the maps, thus increasing the number of current maps available for National Forest System lands. This agreement has improved service to the public by requiring that the agencies share the same maps and that the maps meet a common standard, as well as by significantly reducing duplication of effort.

Chernobyl Studies Project: Working group 7.0, Environmental transport and health effects. Progress report, March--September 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anspaugh, L.R.; Hendrickson, S.M.

1994-12-01

In April 1988, the US and the former-USSR signed a Memorandum of Cooperation (MOC) for Civilian Nuclear Reactor Safety; this MOC was a direct result of the accident at the Chernobyl Nuclear Power Plant Unit 4 and the following efforts by the two countries to implement a joint program to improve the safety of nuclear power plants and to understand the implications of environmental releases. A Joint Coordinating Committee for Civilian Nuclear Reactor Safety (JCCCNRS) was formed to implement the MOC. The JCCCNRS established many working groups; most of these were the responsibility of the Nuclear Regulatory Commission, as farmore » as the US participation was concerned. The lone exception was Working Group 7 on Environmental Transport and Health Effects, for which the US participation was the responsibility of the US Department of Energy (DOE). The purpose of Working Group 7 was succintly stated to be, ``To develop jointly methods to project rapidly the health effects of any future nuclear reactor accident.`` To implement the work DOE then formed two subworking groups: 7.1 to address Environmental Transport and 7.2 to address Health Effects. Thus, the DOE-funded Chernobyl Studies Project began. The majority of the initial tasks for this project are completed or near completion. The focus is now turned to the issue of health effects from the Chernobyl accident. Currently, we are involved in and making progress on the case-control and co-hort studies of thyroid diseases among Belarussian children. Dosimetric aspects are a fundamental part of these studies. We are currently working to implement similar studies in Ukraine. A major part of the effort of these projects is supporting these studies, both by providing methods and applications of dose reconstruction and by providing support and equipment for the medical teams.« less

Joint Implications for Contracted Logistics

DTIC Science & Technology

2007-03-30

authority with the host nation country and policy on using UCMJ for contracted personnel. As tailored theater policies are developed and contracting...responsibility, this paper recommends better joint training, leader development and joint enablers for contracting operations. JOINT...U.S. Joint Forces Command (JFCOM) are analyzing Congressional and DOD policy to develop procedures and force structure to support contractor

Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH) program

NASA Astrophysics Data System (ADS)

Fayette, Daniel F.; Speicher, Patricia; Stoklosa, Mark J.; Evans, Jillian V.; Evans, John W.; Gentile, Mike; Pagel, Chuck A.; Hakim, Edward

1993-08-01

A joint military-commercial effort to evaluate multichip module (MCM) structures is discussed. The program, Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH), has been designed to identify the failure mechanisms that are possible in MCM structures. The RELTECH test vehicles, technical assessment task, product evaluation plan, reliability modeling task, accelerated and environmental testing, and post-test physical analysis and failure analysis are described. The information obtained through RELTECH can be used to address standardization issues, through development of cost effective qualification and appropriate screening criteria, for inclusion into a commercial specification and the MIL-H-38534 general specification for hybrid microcircuits.

Answering Public Health Concerns Over Japanese Nuclear Disaster | ORAU

ScienceCinema

Allen, Leeanna; Vasconez, Rachel

2018-05-11

When the Fukushima Daiichi Nuclear Power Plant became crippled following Japan's March 2011 earthquake and tsunami, some U.S. citizens became concerned about whether radiation would disperse across the Pacific Ocean. As the Centers for Disease Control and Prevention prepared to assist in the U.S. response effort, ORAU provided the CDC with onsite, staff support at its Joint Information Center. ORAU also had a lead role in the development and execution of the CDC's first-ever Bridging the Gaps: Public Health and Radiation Emergency Preparedness conference, which took place 10 days after the earthquake and served as a forum for discussing the current state of radiation emergency preparedness.

Landsat: A Global Land-Imaging Project

USGS Publications Warehouse

Headley, Rachel

2010-01-01

Across nearly four decades since 1972, Landsat satellites continuously have acquired space-based images of the Earth's land surface, coastal shallows, and coral reefs. The Landsat Program, a joint effort of the U.S. Geological Survey (USGS) and the National Aeronautics and Space Administration (NASA), was established to routinely gather land imagery from space; consequently, NASA develops remote-sensing instruments and spacecraft, then launches and validates the satellites. The USGS then assumes ownership and operation of the satellites, in addition to managing all ground-data reception, archiving, product generation, and distribution. The result of this program is a visible, long-term record of natural and human-induced changes on the global landscape.

Landsat: a global land imaging program

USGS Publications Warehouse

Byrnes, Raymond A.

2012-01-01

Landsat satellites have continuously acquired space-based images of the Earth's land surface, coastal shallows, and coral reefs across four decades. The Landsat Program, a joint effort of the U.S. Geological Survey (USGS) and the National Aeronautics and Space Administration (NASA), was established to routinely gather land imagery from space. In practice, NASA develops remote-sensing instruments and spacecraft, launches satellites, and validates their performance. The USGS then assumes ownership and operation of the satellites, in addition to managing all ground-data reception, archiving, product generation, and distribution. The result of this program is a visible, long-term record of natural and human-induced changes on the global landscape.

Nuclear Physics Made Very, Very Easy

NASA Technical Reports Server (NTRS)

Hanlen, D. F.; Morse, W. J.

1968-01-01

The fundamental approach to nuclear physics was prepared to introduce basic reactor principles to various groups of non-nuclear technical personnel associated with NERVA Test Operations. NERVA Test Operations functions as the field test group for the Nuclear Rocket Engine Program. Nuclear Engine for Rocket Vehicle Application (NERVA) program is the combined efforts of Aerojet-General Corporation as prime contractor, and Westinghouse Astronuclear Laboratory as the major subcontractor, for the assembly and testing of nuclear rocket engines. Development of the NERVA Program is under the direction of the Space Nuclear Propulsion Office, a joint agency of the U.S. Atomic Energy Commission and the National Aeronautics and Space Administration.

Nuclear Thermal Propulsion Technology - Summary of FY 1991 Interagency Panel Planning

NASA Technical Reports Server (NTRS)

Clark, John S.; Mcdaniel, Patrick; Howe, Steven; Stanley, Marland

1991-01-01

An Interagency (NASA/DOE/DOD) technical panel has been working in 1991 to evaluate nuclear thermal propulsion (NTP) concepts on a consistent basis, and to continue technology development project planning for a joint project in nuclear propulsion for Space Exploration Initiative (SEI). This paper summarizes the efforts of the panel to date and summarizes the technology plans defined for NTP. Concepts were categorized based on probable technology readiness data, and innovative 'proof-of-concept' tests and analyses were defined. While further studies will be required to provide a consistent comparison of all of the NTP concepts, the current status of the studies is presented.

Combating child homicide: preventive policing for the new millennium.

PubMed

Boudreaux, Monique C; Lord, Wayne D

2005-04-01

High-profile media coverage of crimes against children has heightened public awareness of critical child safety needs and issues. However, numerous research studies in the area of child homicide have illustrated the importance of the power of science to correct false perceptions and misinformation, improving how to best serve and protect our children. Age-based analyses of childhood crime patterns have vastly improved how law enforcement and social service practitioners identify, investigate, and resolve child victimization cases. Future protective efforts must involve multiagency and multidisciplinary collaboration. Law enforcement, social service clinicians, educators, and academicians should jointly develop and implement pragmatic and effective prevention, detection, and resolution programs and policies.

Helicopter simulation validation using flight data

NASA Technical Reports Server (NTRS)

Key, D. L.; Hansen, R. S.; Cleveland, W. B.; Abbott, W. Y.

1982-01-01

A joint NASA/Army effort to perform a systematic ground-based piloted simulation validation assessment is described. The best available mathematical model for the subject helicopter (UH-60A Black Hawk) was programmed for real-time operation. Flight data were obtained to validate the math model, and to develop models for the pilot control strategy while performing mission-type tasks. The validated math model is to be combined with motion and visual systems to perform ground based simulation. Comparisons of the control strategy obtained in flight with that obtained on the simulator are to be used as the basis for assessing the fidelity of the results obtained in the simulator.

Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH) program

NASA Technical Reports Server (NTRS)

Fayette, Daniel F.; Speicher, Patricia; Stoklosa, Mark J.; Evans, Jillian V.; Evans, John W.; Gentile, Mike; Pagel, Chuck A.; Hakim, Edward

1993-01-01

A joint military-commercial effort to evaluate multichip module (MCM) structures is discussed. The program, Reliability Technology to Achieve Insertion of Advanced Packaging (RELTECH), has been designed to identify the failure mechanisms that are possible in MCM structures. The RELTECH test vehicles, technical assessment task, product evaluation plan, reliability modeling task, accelerated and environmental testing, and post-test physical analysis and failure analysis are described. The information obtained through RELTECH can be used to address standardization issues, through development of cost effective qualification and appropriate screening criteria, for inclusion into a commercial specification and the MIL-H-38534 general specification for hybrid microcircuits.

Design and Implementation of CIA, the ISOCAM Interactive Analysis System

NASA Astrophysics Data System (ADS)

Ott, S.; Abergel, A.; Altieri, B.; Augueres, J.-L.; Aussel, H.; Bernard, J.-P.; Biviano, A.; Blommaert, J.; Boulade, O.; Boulanger, F.; Cesarsky, C.; Cesarsky, D. A.; Claret, A.; Delattre, C.; Delaney, M.; Deschamps, T.; Desert, F.-X.; Didelon, P.; Elbaz, D.; Gallais, P.; Gastaud, R.; Guest, S.; Helou, G.; Kong, M.; Lacombe, F.; Li, J.; Landriu, D.; Metcalfe, L.; Okumura, K.; Perault, M.; Pollock, A. M. T.; Rouan, D.; Sam-Lone, J.; Sauvage, M.; Siebenmorgen, R.; Starck, J.-L.; Tran, D.; van Buren, D.; Vigroux, L.; Vivares, F.

This paper presents an overview of the Interactive Analysis System for ISOCAM (CIA). With this system ISOCAM data can be analysed for calibration and engineering purposes, the ISOCAM pipeline software validated and refined, and astronomical data processing can be performed. The system is mainly IDL-based but contains \\fortran, C, and C++ parts for special tasks. It represents an effort of 15 man-years and is comprised of over 1000 IDL and 200 \\fortran, C, and C++ modules. CIA is a joint development by the ESA Astrophysics Division and the ISOCAM Consortium led by the ISOCAM PI, C. Cesarsky, Direction des Sciences de la Matiere, C.E.A., France.

Nested Focusing Optics for Compact Neutron Sources

NASA Technical Reports Server (NTRS)

Nabors, Sammy A.

2015-01-01

NASA's Marshall Space Flight Center, the Massachusetts Institute of Technology (MIT), and the University of Alabama Huntsville (UAH) have developed novel neutron grazing incidence optics for use with small-scale portable neutron generators. The technology was developed to enable the use of commercially available neutron generators for applications requiring high flux densities, including high performance imaging and analysis. Nested grazing incidence mirror optics, with high collection efficiency, are used to produce divergent, parallel, or convergent neutron beams. Ray tracing simulations of the system (with source-object separation of 10m for 5 meV neutrons) show nearly an order of magnitude neutron flux increase on a 1-mm diameter object. The technology is a result of joint development efforts between NASA and MIT researchers seeking to maximize neutron flux from diffuse sources for imaging and testing applications.

Advanced Ceramics for Use as Fuel Element Materials in Nuclear Thermal Propulsion Systems

NASA Technical Reports Server (NTRS)

Valentine, Peter G.; Allen, Lee R.; Shapiro, Alan P.

2012-01-01

With the recent start (October 2011) of the joint National Aeronautics and Space Administration (NASA) and Department of Energy (DOE) Advanced Exploration Systems (AES) Nuclear Cryogenic Propulsion Stage (NCPS) Program, there is renewed interest in developing advanced ceramics for use as fuel element materials in nuclear thermal propulsion (NTP) systems. Three classes of fuel element materials are being considered under the NCPS Program: (a) graphite composites - consisting of coated graphite elements containing uranium carbide (or mixed carbide), (b) cermets (ceramic/metallic composites) - consisting of refractory metal elements containing uranium oxide, and (c) advanced carbides consisting of ceramic elements fabricated from uranium carbide and one or more refractory metal carbides [1]. The current development effort aims to advance the technology originally developed and demonstrated under Project Rover (1955-1973) for the NERVA (Nuclear Engine for Rocket Vehicle Application) [2].

Creation of Real Estate Based on Public Private Partnership and Municipal Private Partnership Agreements in the Russian Federation

NASA Astrophysics Data System (ADS)

Voronina, M. D.

2017-11-01

The article considers individual questions connected with the application of the legislation on public private partnership and municipal private partnership agreements as new types of contracts at the newly built property development. Public private partnership and municipal private partnership agreements are contracts at the initial development stage. Their objective is to attract investments in the Russian economy including for the creation of separate real estate types (capital facilities). The Law enables one to build the relationship in such a way that joint efforts result in the grounds for the accrual of the ownership right to the built (reconstructed) asset. This circumstance certainly influences the infrastructural development of the Russian Federation and its municipal units, the rather that it occurs due to the attraction of extra-budgetary sources

Wind-Driven Montgolfiere Balloons for Mars

NASA Technical Reports Server (NTRS)

Jones, Jack A.; Fairbrother, Debora; Lemieux, Aimee; Lachenmeier, Tim; Zubrin, Robert

2005-01-01

Solar Montgolfiere balloons, or solar-heated hot air balloons have been evaluated by use on Mars for about 5 years. In the past, JPL has developed thermal models that have been confirmed, as well as developed altitude control systems to allow the balloons to float over the landscape or carry ground sampling instrumentation. Pioneer Astronautics has developed and tested a landing system for Montgolfieres. JPL, together with GSSL. have successfully deployed small Montgolfieres (<15-m diameter) in the earth's stratosphere, where conditions are similar to a Mars deployment. Two larger Montgolfieres failed, however, and a series of larger scale Montgolfieres is now planned using stronger, more uniform polyethylene bilaminate, combined with stress-reducing ripstitch and reduced parachute deceleration velocities. This program, which is presently under way, is a joint effort between JPL, WFF, and GSSL, and is planned for completion in three years.

Effect of Joint Commission International Accreditation on the Nursing Work Environment in a Tertiary Medical Center.

PubMed

Kagan, Ilya; Farkash-Fink, Naomi; Fish, Miri

2016-01-01

How might a tertiary hospital's nursing staff respond to the huge improvement effort required for external accreditation if they are encouraged to lead the change process themselves? This article reports the results of a concurrent evaluation of the nursing work climate at ward level, before and after accreditation by the Joint Commission International. Physician-nurse relations improved; the involvement of social workers, dieticians, and physiotherapists increased; support services responded more quickly to requests; and management-line staff relations became closer.

A Mentoring Opportunity: A Joint Effort in Writing Letters of Recommendation.

PubMed

Master, Zubin

2017-01-01

Integrity in writing letters of recommendation is important to academic research because it is an influential criterion used pervasively in peer review. While research in the integrity of recommendation letters has concentrated on contents of the letter, bias, and reliability, few have questioned the process of letter writing. Here, I argue that letter writing should be a joint opportunity between mentor/supervisor/advisor and trainee. It results in more compelling letters, may prevent errors and the use of biased language, and serves as an excellent mentoring opportunity promoting self-reflection.

Epidemiology of osteoarthritis: state of the evidence

PubMed Central

Allen, Kelli D.; Golightly, Yvonne M.

2015-01-01

Purpose of review This review focuses on recent studies of osteoarthritis epidemiology, including research on prevalence, incidence, and a broad array of potential risk factors at the person level and joint level. Recent findings Studies continue to illustrate the high impact of osteoarthritis worldwide, with increasing incidence. Person-level risk factors with strong evidence regarding osteoarthritis incidence and/or progression include age, sex, socioeconomic status, family history, and obesity. Joint-level risk factors with strong evidence for incident osteoarthritis risk include injury and occupational joint loading; the associations of injury and joint alignment with osteoarthritis progression are compelling. Moderate levels of physical activity have not been linked to increased osteoarthritis risk. Some topics of high recent interest or emerging evidence for association with osteoarthritis include metabolic pathways, vitamins, joint shape, bone density, limb length inequality, muscle strength and mass, and early structural damage. Summary Osteoarthritis is a complex, multifactorial disease, and there is still much to learn regarding mechanisms underlying incidence and progression. However, there are several known modifiable and preventable risk factors, including obesity and joint injury; efforts to mitigate these risks can help to lessen the impact of osteoarthritis. PMID:25775186