Consideration of Kaolinite Interference Correction for Quartz Measurements in Coal Mine Dust

PubMed Central

Lee, Taekhee; Chisholm, William P.; Kashon, Michael; Key-Schwartz, Rosa J.; Harper, Martin

2015-01-01

Kaolinite interferes with the infrared analysis of quartz. Improper correction can cause over- or underestimation of silica concentration. The standard sampling method for quartz in coal mine dust is size selective, and, since infrared spectrometry is sensitive to particle size, it is intuitively better to use the same size fractions for quantification of quartz and kaolinite. Standard infrared spectrometric methods for quartz measurement in coal mine dust correct interference from the kaolinite, but they do not specify a particle size for the material used for correction. This study compares calibration curves using as-received and respirable size fractions of nine different examples of kaolinite in the different correction methods from the National Institute for Occupational Safety and Health Manual of Analytical Methods (NMAM) 7603 and the Mine Safety and Health Administration (MSHA) P-7. Four kaolinites showed significant differences between calibration curves with as-received and respirable size fractions for NMAM 7603 and seven for MSHA P-7. The quartz mass measured in 48 samples spiked with respirable fraction silica and kaolinite ranged between 0.28 and 23% (NMAM 7603) and 0.18 and 26% (MSHA P-7) of the expected applied mass when the kaolinite interference was corrected with respirable size fraction kaolinite. This is termed “deviation,” not bias, because the applied mass is also subject to unknown variance. Generally, the deviations in the spiked samples are larger when corrected with the as-received size fraction of kaolinite than with the respirable size fraction. Results indicate that if a kaolinite correction with reference material of respirable size fraction is applied in current standard methods for quartz measurement in coal mine dust, the quartz result would be somewhat closer to the true exposure, although the actual mass difference would be small. Most kinds of kaolinite can be used for laboratory calibration, but preferably, the size

Consideration of kaolinite interference correction for quartz measurements in coal mine dust.

PubMed

Lee, Taekhee; Chisholm, William P; Kashon, Michael; Key-Schwartz, Rosa J; Harper, Martin

2013-01-01

Kaolinite interferes with the infrared analysis of quartz. Improper correction can cause over- or underestimation of silica concentration. The standard sampling method for quartz in coal mine dust is size selective, and, since infrared spectrometry is sensitive to particle size, it is intuitively better to use the same size fractions for quantification of quartz and kaolinite. Standard infrared spectrometric methods for quartz measurement in coal mine dust correct interference from the kaolinite, but they do not specify a particle size for the material used for correction. This study compares calibration curves using as-received and respirable size fractions of nine different examples of kaolinite in the different correction methods from the National Institute for Occupational Safety and Health Manual of Analytical Methods (NMAM) 7603 and the Mine Safety and Health Administration (MSHA) P-7. Four kaolinites showed significant differences between calibration curves with as-received and respirable size fractions for NMAM 7603 and seven for MSHA P-7. The quartz mass measured in 48 samples spiked with respirable fraction silica and kaolinite ranged between 0.28 and 23% (NMAM 7603) and 0.18 and 26% (MSHA P-7) of the expected applied mass when the kaolinite interference was corrected with respirable size fraction kaolinite. This is termed "deviation," not bias, because the applied mass is also subject to unknown variance. Generally, the deviations in the spiked samples are larger when corrected with the as-received size fraction of kaolinite than with the respirable size fraction. Results indicate that if a kaolinite correction with reference material of respirable size fraction is applied in current standard methods for quartz measurement in coal mine dust, the quartz result would be somewhat closer to the true exposure, although the actual mass difference would be small. Most kinds of kaolinite can be used for laboratory calibration, but preferably, the size fraction

Slime coating of kaolinite on chalcopyrite in saline water flotation

NASA Astrophysics Data System (ADS)

Li, Zhi-li; Rao, Feng; Song, Shao-xian; Li, Yan-mei; Liu, Wen-biao

2018-05-01

In saline water flotation, the salinity can cause a distinguishable slime coating of clay minerals on chalcopyrite particles through its effect on their electrical double layers in aqueous solutions. In this work, kaolinite was used as a representative clay mineral for studying slime coating during chalcopyrite flotation. The flotation of chalcopyrite in the presence and absence of kaolinite in tap water, seawater, and gypsum-saturated water and the stability of chalcopyrite and kaolinite particles in slurries are presented. Zeta-potential distributions and scanning electron microscopy images were used to characterize and explain the different slime coating degrees and the different flotation performances. Kaolinite particles induced slime coating on chalcopyrite surfaces and reduced chalcopyrite floatability to the greatest extent when the pH value was in the alkaline range. At 0.24wt% of kaolinite, the chalcopyrite floatability was depressed by more than 10% at alkaline pH levels in tap water. Salinity in seawater and gypsum-saturated water compressed the electrical double layers and resulted in extensive slime coating.

Theoretical study of adsorption of nitrogen-containing environmental contaminants on kaolinite surfaces.

PubMed

Scott, Andrea Michalkova; Burns, Elizabeth A; Hill, Frances C

2014-08-01

The adsorption of nitrogen-containing compounds (NCCs) including 2,4,6-trinitrotoluene (TNT), 2,4-dinitrotoluene (DNT), 2,4-dinitroanisole (DNAN), and 3-nitro-1,2,4-triazol-5-one (NTO) on kaolinite surfaces was investigated. The M06-2X and M06-2X-D3 density functionals were applied with the cluster approximation. Several different positions of NCCs relative to the adsorption sites of kaolinite were examined, including NCCs in perpendicular and parallel orientation toward both surface models of kaolinite. The binding between the target molecules and kaolinite surfaces was analyzed and bond energies were calculated applying the atoms in molecules (AIM) method. All NCCs were found to prefer a parallel orientation toward both kaolinite surfaces, and were bound more strongly to the octahedral than to the tetrahedral site. TNT exhibited the strongest interaction with the octahedral surface and DNAN with the tetrahedral surface of kaolinite. Hydrogen bonding was shown to be the dominant non-covalent interaction for NCCs interacting with the octahedral surface of kaolinite with a small stabilizing effect of dispersion interactions. In the case of adsorption on the tetrahedral surface, kaolonite-NCC binding was shown to be governed by the balance between hydrogen bonds and dispersion forces. The presence of water as a solvent leads to a significant decrease in the adsorption strength for all studied NCCs interacting with both kaolinite surfaces.

Surface Condensation of CO2 onto Kaolinite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Glezakou, Vassiliki Alexandra; Owen, Antionette T.

2014-02-11

The fundamental adsorption behavior of gaseous and supercritical carbon dioxide (CO2) onto poorly crystalline kaolinite (KGa-2) at conditions relevant to geologic sequestration has been investigated using a quartz crystal microbalance (QCM) and density functional theory (DFT) methods. The QCM data indicated linear adsorption of CO2 (0-0.3 mmol CO2/g KGa-2) onto the kaolinite surface up through the gaseous state (0.186 g/cm3). However in the supercritical region, CO2 adsorption increases dramatically, reaching a peak (0.9-1.0 mmol CO2/g KGa-2) near 0.43 g/cm3, before declining rapidly to surface adsorption values equivalent or below gaseous CO2. This adsorption profile was not observed with He ormore » N2. Comparative density functional studies of CO2 interactions with kaolinite surface models rule out CO2 intercalation and confirm that surface adsorption is favored up to approximately 0.35 g/cm3 of CO2, showing distorted T-shaped CO2-CO2 clustering, typical of supercritical CO2 aggregation over the surface as the density increases. Beyond this point, the adsorption energy gain for any additional CO2 becomes less than the CO2 interaction energy (~0.2 eV) in the supercritical medium resulting in overall desorption of CO2 from the kaolinite surface.« less

Remediation of phenanthrene from contaminated kaolinite by electroremediation-Fenton technology.

PubMed

Alcantara, T; Pazos, M; Gouveia, S; Cameselle, C; Sanroman, M A

2008-07-01

Polycyclic aromatic hydrocarbons (PAHs) cause a high environmental impact when released into the environment. The objective of this study was to evaluate the capacity to decontaminate polluted soils with phenanthrene as a model PAH using a combination of two technologies: electrokinetic remediation and Fenton process. Kaolinite was used as a model sample that was artificially polluted at the laboratory at an initial concentration of phenanthrene of 500 mg kg(-1) of dried kaolinite. The standard electrokinetic process resulted in negligible removal of phenanthrene from the kaolinite sample. Faster and more efficient degradation of this compound can be promoted by introduction of a strong oxidant into the soil such as hydroxyl radicals. For this reason, the Fenton reactions have been induced in several experiments in which H(2)O(2) (10%) was used as flushing solution, and kaolinite polluted with iron was used. When anode and cathode chambers were filled with H(2)O(2) (10%), the kaolinite pH is maintained at an acid value around 3.5 without pH control and an overall removal and destruction efficiency of phenanthrene of 99% was obtained in 14 days by applying a voltage gradient of 3 V cm(-1). Therefore, it is evident that a combined technology of electrokinetic remediation and Fenton reaction is capable of simultaneously removing and degrading of PAHs in polluted model samples with kaolinite.

Mechanism Responsible for Intercalation of Dimethyl Sulfoxide in Kaolinite: Molecular Dynamics Simulations.

PubMed

Zhang, Shuai; Liu, Qinfu; Cheng, Hongfei; Gao, Feng; Liu, Cun; Teppen, Brian J

2018-01-01

Intercalation is the promising strategy to expand the interlayer region of kaolinite for their further applications. Herein, the adaptive biasing force (ABF) accelerated molecular dynamics simulations were performed to calculate the free energies involved in the kaolinite intercalation by dimethyl sulfoxide (DMSO). Additionally, the classical all atom molecular dynamics simulations were carried out to calculate the interfacial interactions between kaolinite interlayer surfaces and DMSO with the aim at exploring the underlying force that drives the DMSO to enter the interlayer space. The results showed that the favorable interaction of DMSO with both kaolinite interlayer octahedral surface and tetrahedral surface can help in introducing DMSO enter kaolinite interlayer. The hydroxyl groups on octahedral surface functioned as H-donors attracting the S=O groups of DMSO through hydrogen bonding interaction. The tetrahedral surface featuring hydrophobic property attracted the methyl groups of DMSO through hydrophobic interaction. The results provided a detailed picture of the energetics and interlayer structure of kaolinite-DMSO intercalate.

Surface complexation model of uranyl sorption on Georgia kaolinite

USGS Publications Warehouse

Payne, T.E.; Davis, J.A.; Lumpkin, G.R.; Chisari, R.; Waite, T.D.

2004-01-01

The adsorption of uranyl on standard Georgia kaolinites (KGa-1 and KGa-1B) was studied as a function of pH (3-10), total U (1 and 10 ??mol/l), and mass loading of clay (4 and 40 g/l). The uptake of uranyl in air-equilibrated systems increased with pH and reached a maximum in the near-neutral pH range. At higher pH values, the sorption decreased due to the presence of aqueous uranyl carbonate complexes. One kaolinite sample was examined after the uranyl uptake experiments by transmission electron microscopy (TEM), using energy dispersive X-ray spectroscopy (EDS) to determine the U content. It was found that uranium was preferentially adsorbed by Ti-rich impurity phases (predominantly anatase), which are present in the kaolinite samples. Uranyl sorption on the Georgia kaolinites was simulated with U sorption reactions on both titanol and aluminol sites, using a simple non-electrostatic surface complexation model (SCM). The relative amounts of U-binding >TiOH and >AlOH sites were estimated from the TEM/EDS results. A ternary uranyl carbonate complex on the titanol site improved the fit to the experimental data in the higher pH range. The final model contained only three optimised log K values, and was able to simulate adsorption data across a wide range of experimental conditions. The >TiOH (anatase) sites appear to play an important role in retaining U at low uranyl concentrations. As kaolinite often contains trace TiO2, its presence may need to be taken into account when modelling the results of sorption experiments with radionuclides or trace metals on kaolinite. ?? 2004 Elsevier B.V. All rights reserved.

Effects of ammonium on uranium partitioning and kaolinite mineral dissolution.

PubMed

Emerson, Hilary P; Di Pietro, Silvina; Katsenovich, Yelena; Szecsody, Jim

2017-02-01

Ammonia gas injection is a promising technique for the remediation of uranium within the vadose zone. It can be used to manipulate the pH of a system and cause co-precipitation processes that are expected to remove uranium from the aqueous phase and decrease leaching from the solid phase. The work presented in this paper explores the effects of ammonium and sodium hydroxide on the partitioning of uranium and dissolution of the kaolinite mineral in simplified synthetic groundwaters using equilibrium batch sorption and sequential extraction experiments. It shows that there is a significant increase in uranium removal in systems with divalent cations present in the aqueous phase but not in sodium chloride synthetic groundwaters. Further, the initial conditions of the aqueous phase do not affect the dissolution of kaolinite. However, the type of base treatment does have an effect on mineral dissolution. Published by Elsevier Ltd.

Molecular Treatment of Nano-Kaolinite Generations.

PubMed

Táborosi, Attila; Szilagyi, Robert K; Zsirka, Balázs; Fónagy, Orsolya; Horváth, Erzsébet; Kristóf, János

2018-06-18

A procedure is developed for defining a compositionally and structurally realistic, atomic-scale description of exfoliated clay nanoparticles from the kaolinite family of phylloaluminosilicates. By use of coordination chemical principles, chemical environments within a nanoparticle can be separated into inner, outer, and peripheral spheres. The edges of the molecular models of nanoparticles were protonated in a validated manner to achieve charge neutrality. Structural optimizations using semiempirical methods (NDDO Hamiltonians and DFTB formalism) and ab initio density functionals with a saturated basis set revealed previously overlooked molecular origins of morphological changes as a result of exfoliation. While the use of semiempirical methods is desirable for the treatment of nanoparticles composed of tens of thousands of atoms, the structural accuracy is rather modest in comparison to DFT methods. We report a comparative survey of our infrared data for untreated crystalline and various exfoliated states of kaolinite and halloysite. Given the limited availability of experimental techniques for providing direct structural information about nano-kaolinite, the vibrational spectra can be considered as an essential tool for validating structural models. The comparison of experimental and calculated stretching and bending frequencies further justified the use of the preferred level of theory. Overall, an optimal molecular model of the defect-free, ideal nano-kaolinite can be composed with respect to stationary structure and curvature of the potential energy surface using the PW91/SVP level of theory with empirical dispersion correction (PW91+D) and polarizable continuum solvation model (PCM) without the need for a scaled quantum chemical force field. This validated theoretical approach is essential in order to follow the formation of exfoliated clays and their surface reactivity that is experimentally unattainable.

Uranium (VI) transport in saturated heterogeneous media: Influence of kaolinite and humic acid.

PubMed

Chen, Chong; Zhao, Kang; Shang, Jianying; Liu, Chongxuan; Wang, Jin; Yan, Zhifeng; Liu, Kesi; Wu, Wenliang

2018-05-07

Natural aquifers typically exhibit a variety of structural heterogeneities. However, the effect of mineral colloids and natural organic matter on the transport behavior of uranium (U) in saturated heterogeneous media are not totally understood. In this study, heterogeneous column experiments were conducted, and the constructed columns contained a fast-flow domain (FFD) and a slow-flow domain (SFD). The effect of kaolinite, humic acid (HA), and kaolinite/HA mixture on U(VI) retention and release in saturated heterogeneous media was examined. Media heterogeneity significantly influenced U fate and transport behavior in saturated subsurface environment. The presence of kaolinite, HA, and kaolinite/HA enhanced the mobility of U in heterogeneous media, and the mobility of U was the highest in the presence of kaolinite/HA and the lowest in the presence of kaolinite. In the presence of kaolinite, there was no difference in the amount of U released from the FFD and SFD. However, in the presence of HA and kaolinite/HA, a higher amount of U was released from the FFD. The findings in this study showed that medium structure and mineral colloids, as well as natural organic matter in the aqueous phase had significant effects on U transport and fate in subsurface environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ice formation on kaolinite: Insights from molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Sosso, Gabriele C.; Tribello, Gareth A.; Zen, Andrea; Pedevilla, Philipp; Michaelides, Angelos

2016-12-01

The formation of ice affects many aspects of our everyday life as well as important technologies such as cryotherapy and cryopreservation. Foreign substances almost always aid water freezing through heterogeneous ice nucleation, but the molecular details of this process remain largely unknown. In fact, insight into the microscopic mechanism of ice formation on different substrates is difficult to obtain even if state-of-the-art experimental techniques are used. At the same time, atomistic simulations of heterogeneous ice nucleation frequently face extraordinary challenges due to the complexity of the water-substrate interaction and the long time scales that characterize nucleation events. Here, we have investigated several aspects of molecular dynamics simulations of heterogeneous ice nucleation considering as a prototypical ice nucleating material the clay mineral kaolinite, which is of relevance in atmospheric science. We show via seeded molecular dynamics simulations that ice nucleation on the hydroxylated (001) face of kaolinite proceeds exclusively via the formation of the hexagonal ice polytype. The critical nucleus size is two times smaller than that obtained for homogeneous nucleation at the same supercooling. Previous findings suggested that the flexibility of the kaolinite surface can alter the time scale for ice nucleation within molecular dynamics simulations. However, we here demonstrate that equally flexible (or non flexible) kaolinite surfaces can lead to very different outcomes in terms of ice formation, according to whether or not the surface relaxation of the clay is taken into account. We show that very small structural changes upon relaxation dramatically alter the ability of kaolinite to provide a template for the formation of a hexagonal overlayer of water molecules at the water-kaolinite interface, and that this relaxation therefore determines the nucleation ability of this mineral.

Infrared and infrared emission spectroscopic study of typical Chinese kaolinite and halloysite.

PubMed

Cheng, Hongfei; Frost, Ray L; Yang, Jing; Liu, Qinfu; He, Junkai

2010-12-01

The structure and thermal stability between typical Chinese kaolinite and halloysite were analysed by X-ray diffraction (XRD), infrared spectroscopy, infrared emission spectroscopy (IES) and Raman spectroscopy. Infrared emission spectroscopy over the temperature range of 300-700°C has been used to characterise the thermal decomposition of both kaolinite and halloysite. Halloysite is characterised by two bands in the water bending region at 1629 and 1648 cm(-1), attributed to structural water and coordinated water in the interlayer. Well defined hydroxyl stretching bands at around 3695, 3679, 3652 and 3625 cm(-1) are observed for both kaolinite and halloysite. The 550°C infrared emission spectrum of halloysite is similar to that of kaolinite in 650-1350 cm(-1) spectral region. The infrared emission spectra of halloysite were found to be considerably different to that of kaolinite at lower temperatures. These differences are attributed to the fundamental difference in the structure of the two minerals. Copyright © 2010 Elsevier B.V. All rights reserved.

Adsorption Characteristics of Bixin on Acid- and Alkali-Treated Kaolinite in Aprotic Solvents

PubMed Central

Rahmalia, Winda; Fabre, Jean-François; Usman, Thamrin

2018-01-01

The adsorption of bixin in aprotic solvents onto acid- and alkali-treated kaolinite was investigated. Kaolinite was treated three times, for 6 h each, with 8 M HCl or 5 M KOH. The adsorbents were characterized by XRD, FT-IR, EDS, and BET-N2. The effects of contact time and dye concentration on adsorption capacity and kinetics, electronic transition of bixin before and after adsorption, and also mechanism of bixin-kaolinite adsorption were investigated. Dye adsorption followed pseudo-second order kinetics and was faster in acetone than in dimethyl carbonate. The best adsorption results were obtained for KOH-treated kaolinite. In both of the solvents, the adsorption isotherm followed the Langmuir model and adsorption capacity was higher in dimethyl carbonate (q m = 0.43 mg/g) than in acetone (0.29 mg/g). The adsorption capacity and kinetics of KOH-treated kaolinite (q m = 0.43 mg/g, k 2 = 3.27 g/mg·min) were better than those of HCl-treated kaolinite (q m = 0.21 mg/g, k 2 = 0.25 g/mg·min) and natural kaolinite (q m = 0.18 mg/g, k 2 = 0.32 g/mg·min). There are shift in the band position of maximum intensity of bixin after adsorption on this adsorbent. Adsorption in this system seemed to be based essentially on chemisorption due to the electrostatic interaction of bixin with the strong basic and reducing sites of kaolinite. PMID:29581720

A spectroscopic study of mechanochemically activated kaolinite with the aid of chemometrics.

PubMed

Carmody, Onuma; Kristóf, János; Frost, Ray L; Makó, Eva; Kloprogge, J Theo; Kokot, Serge

2005-07-01

The study of kaolinite surfaces is of industrial importance. In this work we report the application of chemometrics to the study of modified kaolinite surfaces. DRIFT spectra of mechanochemically activated kaolinites (Kiralyhegy, Zettlitz, Szeg, and Birdwood) were analyzed using principal component analysis (PCA) and multicriteria decision making (MCDM) methods, PROMETHEE and GAIA. The clear discrimination of the Kiralyhegy spectral objects on the two PC scores plots (400-800 and 800-2030 cm(-1)) indicated the dominance of quartz. Importantly, no ordering of any spectral objects appeared to be related to grinding time in the PC plots of these spectral regions. Thus, neither the kaolinite nor the quartz, are systematically responsive to grinding time according to the spectral criteria investigated. The third spectral region (2600-3800 cm(-1)OH vibrations), showed apparent systematic ordering of the Kiralyhegy and, to a lesser extent, Zettlitz spectral objects with grinding time. This was attributed to the effect of the natural quartz on the delamination of kaolinite and the accompanying phenomena (i.e., formation of kaolinite spheres and water). With the MCDM methods, it was shown that useful information on the basis of chemical composition, physical properties and grinding time can be obtained. For example, the effects of the minor chemical components (e.g., MgO, K(2)O, etc.) indicated that the Birdwood kaolinite is arguably the most pure one analyzed. In another MCDM experiment, some support was obtained for the apparent trend with grinding time noted in the PC plot of the OH spectral region.

Sorption of Pseudomonas putida onto differently structured kaolinite minerals

NASA Astrophysics Data System (ADS)

Vasiliadou, I. A.; Papoulis, D.; Chrysikopoulos, C.; Panagiotaras, D.; Karakosta, E.; Fardis, M.; Papavassiliou, G.

2010-12-01

The presence of bio-colloids (e.g. bacteria and viruses) in the subsurface could be attributed to the release of particles from septic tanks, broken sewer lines or from artificial recharge with treated municipal wastewater. Bio-colloid transport in the subsurface is significantly affected by sorption onto the solid matrix. Bio-colloid attachment onto mobile or suspended in the aqueous phase soil particles (e.g. clay or other minerals) also may influence their fate and transport in the subsurface. The present study focuses on the investigation of Pseudomonas (Ps.) putida sorption onto well (KGa-1) and poorly (KGa-2) crystallized kaolinite minerals. Batch experiments were carried out to determine the sorption isotherms of Ps. putida onto both types of kaolinite particles. The sorption process of Ps. putida onto KGa-1 and KGa-2 is adequately described by a Langmuir isotherm. Attenuated Total Reflection Fourier Transform Infrared Spectroscopy as well as Nuclear Magnetic Resonance were employed to study the sorption mechanisms of Ps. putida. Experimental results indicated that KGa-2 presented higher affinity and sorption capacity than KGa-1. It was shown that electrostatic interactions and structural disorders can influence the sorption capacity of clay particles.

Role of Organic Acids in Bioformation of Kaolinite: Results of Laboratory Experiments

NASA Astrophysics Data System (ADS)

Bontognali, T. R. R.; Vasconcelos, C.; McKenzie, J. A.

2012-04-01

Clay minerals and other solid silica phases have a broad distribution in the geological record and greatly affect fundamental physicochemical properties of sedimentary rocks, including porosity. An increasing number of studies suggests that microbial activity and microbially produced organic acids might play an important role in authigenic clay mineral formation, at low temperatures and under neutral pH conditions. In particular, early laboratory experiments (Linares and Huertas, 1971) reported the precipitation of kaolinite in solutions of SiO2 and Al2O3 with different molar ratios SiO2/Al2O3, together with fulvic acid (a non-characterized mixture of many different acids containing carboxyl and phenolate groups) that was extracted from peat soil. Despite many attempts, these experiments could not be reproduced until recently. Fiore et al. (2011) hypothesized that the non-sterile fulvic acid might have contained microbes that participated in the formation of kaolinite. Using solutions saturated with Si and Al and containing oxalate and/or mixed microbial culture extracted from peat-moss soil, they performed incubation experiments, which produced kaolinite exclusively in solutions containing oxalate and microbes. We proposed to test the role of specific organic acids for kaolinite formation, conducting laboratory experiments at 25˚C, with solutions of sodium silicate, aluminum chloride and various organic compounds (i.e. EDTA, citric acid, succinic acid and oxalic acid). Specific organic acids may stabilize aluminum in octahedral coordination positions, which is crucial for the initial nucleation step. In our experiments, a poorly crystalline mineral that is possibly a kaolinite precursor formed exclusively in the presence of succinic acid. In experiments with other organic compounds, no incorporation of Al was observed, and amorphous silica was the only precipitated phase. In natural environments, succinic acid is produced by a large variety of microbes as an

Sorption of Cu and Pb to kaolinite-fulvic acid colloids: Assessment of sorbent interactions

NASA Astrophysics Data System (ADS)

Heidmann, Ilona; Christl, Iso; Kretzschmar, Ruben

2005-04-01

The sorption of Cu(II) and Pb(II) to kaolinite-fulvic acid colloids was investigated by potentiometric titrations. To assess the possible interactions between kaolinite and fulvic acid during metal sorption, experimental sorption isotherms were compared with predictions based on a linear additivity model (LAM). Suspensions of 5 g L -1 kaolinite and 0.03 g L -1 fulvic acid in 0.01 M NaNO 3 were titrated with Cu and Pb solutions, respectively. The suspension pH was kept constant at pH 4, 6, or 8. The free ion activities of Cu 2+ and Pb 2+ were monitored in the titration vessel using ion selective electrodes. Total dissolved concentrations of metals (by ICP-MS) and fulvic acid (by UV-absorption) were determined in samples taken after each titration step. The amounts of metals sorbed to the solid phase, comprised of kaolinite plus surface-bound fulvic acid, were calculated by difference. Compared to pure kaolinite, addition of fulvic acid to the clay strongly increased metal sorption to the solid phase. This effect was more pronounced at pH 4 and 6 than at pH 8, because more fulvic acid was sorbed to the kaolinite surface under acidic conditions. Addition of Pb enhanced the sorption of fulvic acid onto kaolinite at pH 6 and 8, but not at pH 4. Addition of Cu had no effect on the sorption of fulvic acid onto kaolinite. In the LAM, metal sorption to the kaolinite surface was predicted by a two-site, 1-pK basic Stern model and metal sorption to the fulvic acid was calculated with the NICA-Donnan model, respectively. The LAM provided good predictions of Cu sorption to the kaolinite-fulvic acid colloids over the entire range in pH and free Cu 2+ ion activity (10 -12 to 10 -5). The sorption of Pb was slightly underestimated by the LAM under most conditions. A fractionation of the fulvic acid during sorption to kaolinite was observed, but this could not explain the observed deviations of the LAM predictions from the experimental Pb sorption isotherms.

Formation of intercalation compound of kaolinite-glycine via displacing guest water by glycine.

PubMed

Zheng, Wan; Zhou, Jing; Zhang, Zhenqian; Chen, Likun; Zhang, Zhongfei; Li, Yong; Ma, Ning; Du, Piyi

2014-10-15

The kaolinite-glycine intercalation compound was successfully formed by displacing intercalated guest water molecules in kaolinite hydrate as a precursor. The microstructure of the compound was characterized by X-ray diffraction, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscope. Results show that glycine can only be intercalated into hydrated kaolinite to form glycine-kaolinite by utilizing water molecules as a transition phase. The intercalated glycine molecules were squeezed partially into the ditrigonal holes in the silicate layer, resulting in the interlayer distance of kaolinite reaching 1.03nm. The proper intercalation temperature range was between 20°C and 80°C. An intercalation time of 24h or above was necessary to ensure the complete formation of kaolinite-glycine. The highest intercalation degree of about 84% appeared when the system was reacted at the temperature of 80°C for 48h. There were two activation energies for the intercalation of glycine into kaolinite, one being 21kJ/mol within the temperature range of 20-65°C and the other 5.8kJ/mol between 65°C and 80°C. The intercalation degree (N) and intercalation velocity (v) of as a function of intercalation time (t) can be empirically expressed as N=-79.35e(-)(t)(/14.8)+80.1 and v=5.37e(-)(t)(/14.8), respectively. Copyright © 2014 Elsevier Inc. All rights reserved.

Intercalation of acrylic acid and sodium acrylate into kaolinite and their in situ polymerization

NASA Astrophysics Data System (ADS)

Zhang, Bo; Li, Yanfeng; Pan, Xiaobing; Jia, Xin; Wang, Xiaolong

2007-02-01

Novel nano-composites of poly (acrylic acid)-kaolinite were prepared, and intercalation and in situ polymerization were used in this process. The nano-composites were obtained by in situ polymerization of acrylic acid (AA) and sodium acrylate (AANa) intercalated into organo-kaolinite, which was obtained by refining and chemically modifying with solution intercalation step in order to increase the basal plane distance of the original clay. The modification was completed by using dimethyl-sulfoxide (DMSO)/methanol and potassium acetate (KAc)/water systems step by step. The materials were characterized with the help of XRD, FT-IR and TEM; the results confirmed that poly(acrylic acid) (PAA) and poly(sodium acrylate) (PAANa) were intercalated into the interlamellar spaces of kaolinite, the resulting copolymer composites (CC0 : copolymer crude kaolinite composite, CC1 : copolymer DMSO kaolinite composite, CC2 : copolymer KAc kaolinite composite) of CC2 exhibited a lamellar nano-composite with a mixed nano-morphology, and partial exfoliation of the intercalating clay platelets should be the main morphology. Finally, the effect of neutralization degree on the intercalation behavior was also investigated.

Luminescence and ESR studies of relationships between O(-)-centres and structural iron in natural and synthetically hydrated kaolinites

NASA Technical Reports Server (NTRS)

Coyne, L. M.; Costanzo, P. M.; Theng, B. K.

1989-01-01

Luminescence, induced by dehydration and by wetting with hydrazine and unsymmetrically substituted hydrazine, and related ESR spectra have been observed from several kaolinites, synthetically hydrated kaolinites, and metahalloysites. The amine-wetting luminescence results suggest that intercalation, not a chemiluminescence reaction, is the luminescence trigger. Correlation between hydration-induced luminescence and g = 2 ESR signals associated with O(-)-centres in several natural halloysites, and concurrent diminution of the intensity of both these signal types as a function of aging in two 8.4 angstroms synthetically hydrated, kaolinites, confirm a previously-reported relationship between the luminescence induced by dehydration and in the presence of O(-)-centres (holes, i.e., electron vacancies) in the tetrahedral sheet. Furthermore, the ESR spectra of the 8.4 angstroms hydrate showed a concurrent change in the line shape of the g = 4 signal from a shape usually associated with structural Fe in an ordered kaolinite, to a simpler one typically observed in more disordered kaolinite, halloysite, and montmorillonite. Either structural Fe centres and the O(-)-centres interact, or both are subject to factors previously associated with degree of order. The results question the long-term stability of the 8.4 angstroms hydrate, although XRD does not indicate interlayer collapse over this period. Complex inter-relationships are shown between intercalation, stored energy, structural Fe, and the degree of hydration which may be reflected in catalytic as well as spectroscopic properties of the clays.

Characterization of dehydration-induced luminescence of kaolinite

NASA Technical Reports Server (NTRS)

Lahav, N.; Coyne, L.; Lawless, J. G.

1985-01-01

The dehydration-induced luminescence of a colloidal kaolinite is investigated experimentally, with particular attention given to the effect of various treatments on the luminescence characteristics. It is found that the total photon count of the emitted light is linearly related to the film thickness up to a thickness of 30 microns; mechanical stress in the form of grinding increases the photon output and produces extensive changes in the emission kinetics. A direct check of the emission wavelength dependence (by using color filters) indicates that roughly 75 percent of the emission occurs in the wavelength range below 410 nm. It is also found that incorporation of fluorescent molecules into the kaolinite paste increases the photon output and may indicate the transfer of ultraviolet photons to the fluorescent probe.

Antibacterial kaolinite/urea/chlorhexidine nanocomposites: Experiment and molecular modelling

NASA Astrophysics Data System (ADS)

Holešová, Sylva; Valášková, Marta; Hlaváč, Dominik; Madejová, Jana; Samlíková, Magda; Tokarský, Jonáš; Pazdziora, Erich

2014-06-01

Clay minerals are commonly used materials in pharmaceutical production both as inorganic carriers or active agents. The purpose of this study is the preparation and characterization of clay/antibacterial drug hybrids which can be further included in drug delivery systems for treatment oral infections. Novel nanocomposites with antibacterial properties were successfully prepared by ion exchange reaction from two types of kaolinite/urea intercalates and chlorhexidine diacetate. Intercalation compounds of kaolinite were prepared by reaction with solid urea in the absence of solvents (dry method) as well as with urea aqueous solution (wet method). The antibacterial activity of two prepared samples against Enterococcus faecalis, Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa was evaluated by finding the minimum inhibitory concentration (MIC). Antibacterial studies of both samples showed the lowest MIC values (0.01%, w/v) after 1 day against E. faecalis, E. coli and S. aureus. A slightly worse antibacterial activity was observed against P. aeruginosa (MIC 0.12%, w/v) after 1 day. Since samples showed very good antibacterial activity, especially after 1 day of action, this means that these samples can be used as long-acting antibacterial materials. Prepared samples were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The experimental data are supported by results of molecular modelling.

Synthesis and investigation of proton conductivity for intercalated kaolinite with 4-amidinopyridinium chloride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ren, Li-Te; College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009; Li, Xiao-Pei

2015-12-15

The proton-conducting materials have potential application in devices such as fuel cells. In this study, a mineral kaolinite-based proton conducting material, kaolinite-4-amidinopyridinium hydrochloride (K-4-APy–HCl), was synthesized by the intercalated compound kaolinite-4-amidinopyridine (K-4-APy) adsorbing volatilizing HCl. The thermogravimetric analysis (TG), powder X-ray diffraction (PXRD) and IR spectrum confirmed the HCl successfully inserting into the interlayer space of kaolinite and the 4-aminopyridine being protonated. The intercalation efficiency is estimated to be ca. 85.6%. With respect to K-4-APy, the interlayer space expends by 1.53 Å. The thermal decomposition mechanism was studied by PXRD and TG techniques. The K-4-APy–HCl shows proton conductivity with σ=3.379×10{supmore » −8} S cm{sup −1} at 373 K and E{sub a}=1.159 eV in the anhydrous condition, which are comparable to MOFs-based proton conducting materials. - Graphical abstract: The intercalated hybrid of mineral kaolinite with 4-amidinopyridinium hydrochloride is prepared to use as proton conducting material. - Highlights: • A new strategy is proposed for preparation of kaolinite-based proton conductor. • Intercalatied hybrid was prepared by sequentially inserting 4-amidinopyridine and adsorbing HCl. • The proton conductivity of intercalated hybrid is comparable to MOFs-based proton-conductors.« less

Methoxy-modified kaolinite as a novel carrier for high-capacity loading and controlled-release of the herbicide amitrole

PubMed Central

Tan, Daoyong; Yuan, Peng; Annabi-Bergaya, Faïza; Liu, Dong; He, Hongping

2015-01-01

Methoxy-modified kaolinite was used as a novel carrier for loading and release of the herbicide 3-amino-1,2,4-triazole, known as amitrole (abbreviated here as AMT). The methoxy modification made the interlayer space of the kaolinite available for AMT intercalation. The AMT loading content in methoxy-modified kaolinite reached up to 20.8 mass% (twice the loading content by unmodified kaolinite). About 48% of this amount is located in the interlayer space. The release profiles of the AMT fit with the modified Korsmeyer-Peppas model. Due to the diffusional restriction of the intercalated AMT by the lamellar structure of the kaolinite and the strong electrostatic attraction between the intercalated AMT and the kaolinite, a slow release of AMT from the methoxy-modified kaolinite was achieved. These results show that the methoxy-modification is a facile method to make the interlayer space of kaolinite available for hosting other guest molecules. The methoxy-modified kaolinite is a promising candidate for high-capacity loading and controlled-release of other molecules such as drugs, agrochemicals, and biochemicals. PMID:25747124

Methoxy-modified kaolinite as a novel carrier for high-capacity loading and controlled-release of the herbicide amitrole

NASA Astrophysics Data System (ADS)

Tan, Daoyong; Yuan, Peng; Annabi-Bergaya, Faïza; Liu, Dong; He, Hongping

2015-03-01

Methoxy-modified kaolinite was used as a novel carrier for loading and release of the herbicide 3-amino-1,2,4-triazole, known as amitrole (abbreviated here as AMT). The methoxy modification made the interlayer space of the kaolinite available for AMT intercalation. The AMT loading content in methoxy-modified kaolinite reached up to 20.8 mass% (twice the loading content by unmodified kaolinite). About 48% of this amount is located in the interlayer space. The release profiles of the AMT fit with the modified Korsmeyer-Peppas model. Due to the diffusional restriction of the intercalated AMT by the lamellar structure of the kaolinite and the strong electrostatic attraction between the intercalated AMT and the kaolinite, a slow release of AMT from the methoxy-modified kaolinite was achieved. These results show that the methoxy-modification is a facile method to make the interlayer space of kaolinite available for hosting other guest molecules. The methoxy-modified kaolinite is a promising candidate for high-capacity loading and controlled-release of other molecules such as drugs, agrochemicals, and biochemicals.

Acidity of edge surface sites of montmorillonite and kaolinite

NASA Astrophysics Data System (ADS)

Liu, Xiandong; Lu, Xiancai; Sprik, Michiel; Cheng, Jun; Meijer, Evert Jan; Wang, Rucheng

2013-09-01

Acid-base chemistry of clay minerals is central to their interfacial properties, but up to now a quantitative understanding on the surface acidity is still lacking. In this study, with first principles molecular dynamics (FPMD) based vertical energy gap technique, we calculate the acidity constants of surface groups on (0 1 0)-type edges of montmorillonite and kaolinite, which are representatives of 2:1 and 1:1-type clay minerals, respectively. It shows that tbnd Si-OH and tbnd Al-OH2OH groups of kaolinite have pKas of 6.9 and 5.7 and those of montmorillonite have pKas of 7.0 and 8.3, respectively. For each mineral, the calculated pKas are consistent with the experimental ranges derived from fittings of titration curves, indicating that tbnd Si-OH and tbnd Al-OH2OH groups are the major acidic sites responsible to pH-dependent experimental observations. The effect of Mg substitution in montmorillonite is investigated and it is found that Mg substitution increases the pKas of the neighboring tbnd Si-OH and tbnd Si-OH2 groups by 2-3 pKa units. Furthermore, our calculation shows that the pKa of edge tbnd Mg-(OH2)2 is as high as 13.2, indicating the protonated state dominates under common pH. Together with previous adsorption experiments, our derived acidity constants suggest that tbnd Si-O- and tbnd Al-(OH)2 groups are the most probable edge sites for complexing heavy metal cations.

Kaolinite Nanocomposite Platelets Synthesized by Intercalation and Imidization of Poly(styrene-co-maleic anhydride)

PubMed Central

Samyn, Pieter; Schoukens, Gustaaf; Stanssens, Dirk

2015-01-01

A synthesis route is presented for the subsequent intercalation, exfoliation and surface modification of kaolinite (Kln) by an imidization reaction of high-molecular weight poly(styrene-co-maleic anhydride) or SMA in the presence of ammonium hydroxide. In a first step, the intercalation of ammonolyzed SMA by guest displacement of intercalated dimethylsulfoxide has been proven. In a second step, the imidization of ammonolyzed SMA at 160 °C results in exfoliation of the kaolinite layers and deposition of poly(styrene-co-maleimide) or SMI nanoparticles onto the kaolinite surfaces. Compared with a physical mixture of Kln/SMI, the chemically reacted Kln/SMI provides more efficient exfoliation and hydrogen bonding between the nanoparticles and the kaolinite. The kaolinite nanocomposite particles are synthesized in aqueous dispersion with solid content of 65 wt %. The intercalation and exfoliation are optimized for a concentration ratio of Kln/SMI = 70:30, resulting in maximum intercalation and interlayer distance in combination with highest imide content. After thermal curing at 135 °C, the imidization proceeds towards a maximum conversion of the intermediate amic acid moieties. The changes in O–H stretching and kaolinite lattice vibrations have been illustrated by infrared and FT-Raman spectroscopy, which allow for a good quantification of concentration and imidization effects. PMID:28793445

Adsorption of etheramine on kaolinite: a cheap alternative for the treatment of mining effluents.

PubMed

Magriotis, Zuy M; Leal, Paulo V B; Sales, Priscila F; Papini, Rísia M; Viana, Paulo R M

2010-12-15

The results of laboratory experiments aimed at determining the influence of physicochemical parameters on the adsorption of etheramine (adsorbate) on white, pink and yellow kaolinites (adsorbent) are presented. The adsorption of etheramine was favoured at pH 10.0 under conditions where the initial concentration of etheramine was 200 mg l(-1) and the ratio of adsorbent to volume of etheramine solution was 1:100 g ml(-1). Equilibrium adsorption was attained within 30 min and the efficiencies of removal of etheramine by white, pink and yellow kaolinite were 77%, 80% and 69%, respectively. The adsorption isotherms of the kaolinites were determined under optimum conditions and with adsorbate in the concentration range of 0-4000 mg l(-1). The amounts of etheramine adsorbed per unit mass of adsorbent were 33.03, 34.32 and 23.11 mg g(-1) for white, pink and yellow kaolinites, respectively. The adsorption of etheramine on kaolinites was better fitted to the Langmuir rather than the Freundlich isotherm, and could be explained by a pseudo-second-order kinetic model. It is concluded that kaolinites offer significant potential in the treatment of effluents originating from the processing of lower grade iron ores by froth flotation. Copyright © 2010 Elsevier B.V. All rights reserved.

Preparation and characterization of photoactive composite kaolinite/TiO(2).

PubMed

Mamulová Kutláková, K; Tokarský, J; Kovář, P; Vojtěšková, S; Kovářová, A; Smetana, B; Kukutschová, J; Čapková, P; Matějka, V

2011-04-15

Preparation of nanocomposite kaolinite/TiO(2), using hydrolysis of titanyl sulfate in the presence of kaolin was addressed. A variable (kaolin)/(titanyl sulfate) ratio has been used in order to achieve the desired TiO(2) content in prepared nanocomposites. Calcination of the composites at 600 °C led to the transformation of the kaolinite to metakaolinite and to origination of metakaolinite/TiO(2) composites. The prepared samples were investigated using X-ray fluorescence spectroscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetry and diffuse reflectance spectroscopy in the UV-VIS region. Structural ordering of TiO(2) on the kaolinite particle surface was modeled using empirical force field atomistic simulations in the Material Studio modeling environment. Photodegradation activity of the composites prepared was evaluated by the discoloration of Acid Orange 7 aqueous solution. Copyright © 2011 Elsevier B.V. All rights reserved.

Coagulation processes of kaolinite and montmorillonite in calm, saline water

NASA Astrophysics Data System (ADS)

Zhang, Jin-Feng; Zhang, Qing-He; Maa, Jerome P.-Y.

2018-03-01

A three dimensional numerical model for simulating the coagulation processes of colloids has been performed by monitoring the time evolution of particle number concentration, the size distribution of aggregates, the averaged settling velocity, the collision frequency, and the collision efficiency in quiescent water with selected salinities. This model directly simulates all interaction forces between particles based on the lattice Boltzmann method (LBM) and the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, and thus, can reveal the collision and coagulation processes of colloidal suspensions. Although using perfect spherical particles in the modeling, the results were compared with those for kaolinite and montmorillonite suspensions to demonstrate the capability of simulating the responses of these particles with highly irregular shape. The averaged settling velocity of kaolinite aggregates in quiescent saline water reached a maximum of 0.16 mm/s when the salinity increasing to about 3, and then, exhibited little dependence on salinity thereafter. Model simulations results (by choosing specific values that represent kaolinite's characteristics) indicate a similar trend: rapid decrease of the particle number concentration (i.e., rapidly flocculated, and thus, settling velocity also increases rapidly) when salinity increases from 0 to 2, and then, only increased slightly when salinity was further increased from 5 to 20. The collision frequency for kaolinite only decreases slightly with increasing salinity because that the fluid density and viscosity increase slightly in sea water. It suggests that the collision efficiency for kaolinite rises rapidly at low salinities and levels off at high salinity. For montmorillonite, the settling velocity of aggregates in quiescent saline water continuedly increases to 0.022 mm/s over the whole salinity range 0-20, and the collision efficiency for montmorillonite rises with increasing salinities.

A role for subducted super-hydrated kaolinite in Earth's deep water cycle

NASA Astrophysics Data System (ADS)

Hwang, Huijeong; Seoung, Donghoon; Lee, Yongjae; Liu, Zhenxian; Liermann, Hanns-Peter; Cynn, Hyunchae; Vogt, Thomas; Kao, Chi-Chang; Mao, Ho-Kwang

2017-12-01

Water is the most abundant volatile component in the Earth. It continuously enters the mantle through subduction zones, where it reduces the melting temperature of rocks to generate magmas. The dehydration process in subduction zones, which determines whether water is released from the slab or transported into the deeper mantle, is an essential component of the deep water cycle. Here we use in situ and time-resolved high-pressure/high-temperature synchrotron X-ray diffraction and infrared spectra to characterize the structural and chemical changes of the clay mineral kaolinite. At conditions corresponding to a depth of about 75 km in a cold subducting slab (2.7 GPa and 200 °C), and in the presence of water, we observe the pressure-induced insertion of water into kaolinite. This super-hydrated phase has a unit cell volume that is about 31% larger, a density that is about 8.4% lower than the original kaolinite and, with 29 wt% H2O, the highest water content of any known aluminosilicate mineral in the Earth. As pressure and temperature approach 19 GPa and about 800 °C, we observe the sequential breakdown of super-hydrated kaolinite. The formation and subsequent breakdown of super-hydrated kaolinite in cold slabs subducted below 200 km leads to the release of water that may affect seismicity and help fuel arc volcanism at the surface.

Porous Materials from Thermally Activated Kaolinite: Preparation, Characterization and Application

PubMed Central

Luo, Jun; Jiang, Tao; Li, Guanghui; Peng, Zhiwei; Rao, Mingjun; Zhang, Yuanbo

2017-01-01

In the present study, porous alumina/silica materials were prepared by selective leaching of silicon/aluminum constituents from thermal-activated kaolinite in inorganic acid or alkali liquor. The correlations between the characteristics of the prepared porous materials and the dissolution properties of activated kaolinite were also investigated. The results show that the specific surface area (SSA) of porous alumina/silica increases with silica/alumina dissolution, but without marked change of the BJH pore size. Furthermore, change in pore volume is more dependent on activation temperature. The porous alumina and silica obtained from alkali leaching of kaolinite activated at 1150 °C for 15 min and acid leaching of kaolinite activated at 850 °C for 15 min are mesoporous, with SSAs, BJH pore sizes and pore volumes of 55.8 m2/g and 280.3 m2/g, 6.06 nm and 3.06 nm, 0.1455 mL/g and 0.1945 mL/g, respectively. According to the adsorption tests, porous alumina has superior adsorption capacities for Cu2+, Pb2+ and Cd2+ compared with porous silica and activated carbon. The maximum capacities of porous alumina for Cu2+, Pb2+ and Cd2+ are 134 mg/g, 183 mg/g and 195 mg/g, respectively, at 30 °C. PMID:28773002

Modification of kaolinite surfaces through mechanochemical activation with quartz: A diffuse reflectance infrared fourier transform and chemometrics study.

PubMed

Carmody, Onuma; Frost, Ray L; Kristóf, János; Kokot, Serge; Kloprogge, J Theo; Makó, Eva

2006-12-01

Studies of kaolinite surfaces are of industrial importance. One useful method for studying the changes in kaolinite surface properties is to apply chemometric analyses to the kaolinite surface infrared spectra. A comparison is made between the mechanochemical activation of Kiralyhegy kaolinites with significant amounts of natural quartz and the mechanochemical activation of Zettlitz kaolinite with added quartz. Diffuse reflectance infrared Fourier transform (DRIFT) spectra were analyzed using principal component analysis (PCA) and multi-criteria decision making (MCDM) methods, the preference ranking organization method for enrichment evaluations (PROMETHEE) and geometrical analysis for interactive assistance (GAIA). The clear discrimination of the Kiralyhegy spectral objects on the two PC scores plots (400-800 and 800-2030 cm(-1)) indicated the dominance of quartz. Importantly, no ordering of any spectral objects appeared to be related to grinding time in the PC plots of these spectral regions. Thus, neither the kaolinite nor the quartz are systematically responsive to grinding time according to the spectral criteria investigated. The third spectral region (2600-3800 cm(-1), OH vibrations), showed apparent systematic ordering of the Kiralyhegy and, to a lesser extent, Zettlitz spectral objects with grinding time. This was attributed to the effect of the natural quartz on the delamination of kaolinite and the accompanying phenomena (i.e., formation of kaolinite spheres and water). The mechanochemical activation of kaolinite and quartz, through dry grinding, results in changes to the surface structure. Different grinding times were adopted to study the rate of destruction of the kaolinite and quartz structures. This relationship (i.e., grinding time) was classified using PROMETHEE and GAIA methodology.

Effect of water on methane adsorption on the kaolinite (0 0 1) surface based on molecular simulations

NASA Astrophysics Data System (ADS)

Zhang, Bin; Kang, Jianting; Kang, Tianhe

2018-05-01

CH4 adsorption isotherms of kaolinite with moisture contents ranging from 0 to 5 wt% water, the effects of water on maximum adsorption capacity, kaolinite swelling, and radial distribution function were modelled by the implementing combined Monte Carlo (MC) and molecular dynamics (MD) simulations at 293.15 K (20 °C) and a pressure range of 1-20 MPa. The simulation results showed that the absolute adsorption of CH4 on both dry and moist kaolinite followed a Langmuir isotherm within the simulated pressure range, and both the adsorption capacity and the rate of CH4 adsorption decreased with the water content increases. The adsorption isosteric heats of CH4 on kaolinite decreased linearly with increasing water content, indicating that at higher water contents, the interaction energy between the CH4 and kaolinite was weaker. The interaction between kaolinite and water dominates and was the main contributing factor to kaolinite clay swelling. Water molecules were preferentially adsorbed onto oxygen and hydrogen atoms in kaolinite, while methane showed a tendency to be adsorbed only onto oxygen. The simulation results of our study provide the quantitative analysis of effect of water on CH4 adsorption capacity, adsorption rate, and interaction energy from a microscopic perspective. We hope that our study will contribute to the development of strategies for the further exploration of coal bed methane and shale gas.

Mixed-layer kaolinite-montmorillonite from the Yucatan Peninsula, Mexico

USGS Publications Warehouse

Schultz, L.G.; Shepard, A.O.; Blackmon, P.D.; Starkey, H.C.

1971-01-01

Clay beds 1–2 m thick and interbedded with marine limestones probably of early Eocene age are composed of nearly pure mixed-layer kaolinite-montmorillonite. Particle size studies, electron micrographs, X-ray diffraction studies, chemical analyses, cation exchange experiments, DTA, and TGA indicate that clays from three different localities contain roughly equal proportions of randomly interlayered kaolinite and montmorillonite layers. The montmorillonite structural formulas average K0·2Na0·2Ca0·2Mg0·2(Al2·5Fe1·03+Mg0·5)(Al0·75Si7.25)O20+(OH)4−, with a deficiency of structural (OH) in either the montmorillonite or kaolinite layers. Nonexchangeable K+ indicates that a few layers are mica-like. Crystals are mostly round plates 1/10 to 1/20 µ across. The feature most diagnostic of the mixed-layer character is an X-ray reflection near 8 Å after heating at 300°C. The clays are inferred to have developed by weathering of volcanic ash and subsequent erosion and deposition in protected nearshore basins.

Effects of low temperature on coagulation of kaolinite suspensions.

PubMed

Xiao, Feng; Ma, Jun; Yi, Peng; Huang, Ju-Chang Howard

2008-06-01

In this study, coagulation of kaolinite suspensions at low temperatures is compared with that at an ambient temperature of 22 degrees C, and the process is examined with regard to the coagulation rate (CR) and chemical aspects of coagulation. Experiments using a photometric dispersion analyzer (PDA) show that coagulation of kaolinite suspensions can be taken as a two-phase process. Low temperature greatly reduces the CR of the first phase but not that of the second one. On the other hand, results show that low temperature did not serve to impede the hydrolysis of aluminum [Al(III)] within 1 min of alum addition. The measurements of electrophoretic mobility (EM) indicate that destabilization of kaolinite particles by hydrolyzed Al species was not hindered by low temperature within 1 min of alum addition. Slow coagulation at low temperature is due to the lowered CR but not the altered chemistry aspect of Al(III). Furthermore, the change in settled turbidity after 20-min flocculation as a function of coagulant dosage was more severe in the cold because of the low CR. Elongating floc-growth time, as observed, was able to counterbalance the retarded CR at low temperature and improve turbidity removal efficiency.

Effect of Dissolved NaC1 on Freezing Curves of Kaolinite, Montmorillonite, and Sand Pastes,

DTIC Science & Technology

1999-01-01

test this procedure. Pastes of kaolinite clay, montmorillonite , and quartz sand were prepared by washing repeatedly with aque- ous solutions of 0.1...Cold Regions Research & Engineering Laboratory Effect of Dissolved NaCI on Freezing Curves of Kaolinite , Montmorillonite , and Sand Pastes S.A...of kaolinite pastes warmed from -66.6°C to 0°C 8 4. Unfrozen-water contents, as measured by pulsed NMR, of montmorillonite pastes cooled from 0

Cesium sorption reversibility and kinetics on illite, montmorillonite, and kaolinite

DOE PAGES

Durrant, Chad B.; Begg, James D.; Kersting, Annie B.; ...

2017-08-17

Understanding sorption and desorption processes is essential to predicting the mobility of radionuclides in the environment. In this study, we investigate adsorption/desorption of cesium in both binary (Cs + one mineral) and ternary (Cs + two minerals) experiments to study component additivity and sorption reversibility over long time periods (500 days). Binary Cs sorption experiments were performed with illite, montmorillonite, and kaolinite in a 5 mM NaCl/0.7 mM NaHCO3 solution (pH 8) and Cs concentration range of 10 –3 to 10 –11 M. The binary sorption experiments were followed by batch desorption experiments. The sorption behavior was modeled with themore » FIT4FD code and the results used to predict desorption behavior. Sorption to montmorillonite and kaolinite was linear over the entire concentration range but sorption to illite was non-linear, indicating the presence of multiple sorption sites. Based on the 14 day batch desorption data, cesium sorption appeared irreversible at high surface loadings in the case of illite but reversible at all concentrations for montmorillonite and kaolinite. Additionally, a novel experimental approach, using a dialysis membrane, was adopted in the ternary experiments, allowing investigation of the effect of a second mineral on Cs desorption from the original mineral. Cs was first sorbed to illite, montmorillonite or kaolinite, then a 3.5–5 kDalton Float-A-Lyzer® dialysis bag with 0.3 g of illite was introduced to each experiment inducing desorption. Nearly complete Cs desorption from kaolinite and montmorillonite was observed over the experiment, consistent with our equilibrium model, indicating complete Cs desorption from these minerals. Results from the long-term ternary experiments show significantly greater Cs desorption compared to the binary desorption experiments. Approximately ~ 45% of Cs desorbed from illite. However, our equilibrium model predicted ~ 65% desorption. Importantly, the data imply that in some

Authigenic kaolinite and associated pyrite in chalk of the Cretaceous Niobrara Formation, Eastern Colorado.

USGS Publications Warehouse

Pollastro, R.M.

1981-01-01

Cores from the Smoky Hill Chalk Member of the Cretaceous Niobrara Formation have several zones containing authigenic kaolinite as spherical, moldic, polycrystalline aggregates that occur within single or multichambered foraminiferal tests and are commonly associated with framboidal pyrite. Such kaolinite is inferred to result from volcanic ash deposited during chalk sedimentation. Shortly after burial, a colloidal aluminous gel or solution formed from the unstable ash and moved into organic-rich foraminiferal tests, where sulfate-reducing bacteria created a favorable microenvironment for the simultaneous crystallization of kaolinite and pyrite. -Author

Short-time dissolution mechanisms of kaolinitic tropical soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malengreau, N.; Sposito, Garrison

1996-03-01

Previous research on the short-time dissolution behavior of kaolinitic Oxisols suggested pH-dependent kinetics involving ligand-promoted dissolution, metal readsorption, and colloidal dispersion, with soil organic matter conjectured to play a decisive role. A novel combination of spectroscopy, lightscattering, and batch dissolution experiments, conducted at controlled pH and ionic strength over five dissolution periods ranging from 1 to 12 h, was applied to evaluate this mechanism for samples of a representative kaolinitic Oxisol; collected at both forested and cultivated field sites (leading to significant differences in organic matter content and field soil pH). The overall characteristics of the pH-dependent net release kineticsmore » of Al, Fe, and Si by the soil samples, for any dissolution period in the range investigated, were determined by the pH value at which colloid dispersion commenced, which decreased significantly as the soil organic matter content increased. Plots of log(Si/Al released) (or Si/Fe released) vs. -log [H+] ([H+] is proton concentration) were superimposable for all dissolution periods studied, rising to a plateau value above the point of zero net charge of the soils (pH 3.2). Light-scattering and X-ray diffraction data showed conclusively that this plateau represented the release of siliceous colloids containing kaolinite and X-ray amorphous material. X-ray diffraction, UV-visible diffuse reflectance spectroscopy, and electron spin resonance spectroscopy, applied to the soil samples before and after dissolution, and after conventional chemical extractions to remove Al, C, Fe, and Si, showed that kaolinite and iron oxide phases (the latter being highly Al-substituted and present in both coatings and occlusions) were essentially unaltered by dissolution, even at -log [H+] = 2, whereas substantial dissolution loss of soil quartz occurred. Diffuse reflectance spectroscopy gave strong evidence that C in these soils occurs principally in

The Effect of Thermal and Mechanical Treatments on Kaolinite: Characterization by XPS and IEP Measurements.

PubMed

Torres Sánchez RM; Basaldella; Marco

1999-07-15

The surface transformations induced on kaolinite by different thermal and mechanical treatments have been investigated by means of X-ray photoelectron spectroscopy (XPS), Bremsstrahlung induced Auger spectroscopy, and isoelectric point (IEP) measurements. Heating the kaolinite at temperatures between 500 and 750 degrees C results in the change of a substantial fraction of surface Al from octahedral to tetrahedral coordination, which we associate with the dehydroxylation of kaolinite. Heating at 900 and 980 degrees C brings about the development of an octahedral Al fraction which is associated with the formation of gamma-Al(2)O(3). The development of an Al tetrahedral component in the Al KLL spectra of the mechanically treated (ground) samples has been also observed. The Si/Al atomic ratio obtained by XPS in the thermally treated samples is the same as that shown by the original kaolinite. However, the XPS data show a clear reduction of the Si/Al atomic ratio in the mechanically treated samples, which suggests that the mechanical treatment has induced an Al enrichment of the kaolinite surface. The IEP values indicated a thermal transformation to metakaolinite and mullite with the increase of temperature (750 to 980 degrees C). The IEP change for the milled samples can be only explained by assuming a 30% kaolinite coating by the Al oxide neoformed by grinding. Copyright 1999 Academic Press.

Probing adsorption of polyacrylamide-based polymers on anisotropic Basal planes of kaolinite using quartz crystal microbalance.

PubMed

Alagha, Lana; Wang, Shengqun; Yan, Lujie; Xu, Zhenghe; Masliyah, Jacob

2013-03-26

Quartz crystal microbalance with dissipation (QCM-D) was applied to investigate the adsorption characteristics of polyacrylamide-based polymers (PAMs) on anisotropic basal planes of kaolinite. Kaolinite basal planes were differentiated by depositing kaolinite nanoparticles (KNPs) on silica and alumina sensors in solutions of controlled pH values. Adsorption of an in-house synthesized organic-inorganic Al(OH)3-PAM (Al-PAM) as an example of cationic hybrid PAM and a commercially available partially hydrolyzed polyacrylamide (MF1011) as an example of anionic PAM was studied. Cationic Al-PAM was found to adsorb irreversibly and preferentially on tetrahedral silica basal planes of kaolinite. In contrast, anionic MF1011 adsorbed strongly on aluminum-hydroxy basal planes, while its adsorption on tetrahedral silica basal planes was weak and reversible. Adsorption study revealed that both electrostatic attraction and hydrogen-bonding mechanisms contribute to adsorption of PAMs on kaolinite. The adsorbed Al-PAM layer was able to release trapped water overtime and became more compact, while MF1011 film became more dissipative as backbones stretched out from kaolinite surface with minimal overlapping. Experimental results obtained from this study provide clear insights into the phenomenon that governs flocculation-based solid-liquid separation processes using multicomponent flocculants of anionic and cationic nature.

A role for subducted super-hydrated kaolinite in Earth’s deep water cycle

DOE PAGES

Hwang, Huijeong; Seoung, Donghoon; Lee, Yongjae; ...

2017-11-20

Water is the most abundant volatile component in the Earth. It continuously enters the mantle through subduction zones, where it reduces the melting temperature of rocks to generate magmas. The dehydration process in subduction zones, which determines whether water is released from the slab or transported into the deeper mantle, is an essential component of the deep water cycle. Here in this paper we use in situ and time-resolved high-pressure/high-temperature synchrotron X-ray diffraction and infrared spectra to characterize the structural and chemical changes of the clay mineral kaolinite. At conditions corresponding to a depth of about 75 km in amore » cold subducting slab (2.7 GPa and 200 °C), and in the presence of water, we observe the pressure-induced insertion of water into kaolinite. This super-hydrated phase has a unit cell volume that is about 31% larger, a density that is about 8.4% lower than the original kaolinite and, with 29 wt% H 2O, the highest water content of any known aluminosilicate mineral in the Earth. As pressure and temperature approach 19 GPa and about 800 °C, we observe the sequential breakdown of super-hydrated kaolinite. The formation and subsequent breakdown of super-hydrated kaolinite in cold slabs subducted below 200 km leads to the release of water that may affect seismicity and help fuel arc volcanism at the surface.« less

A role for subducted super-hydrated kaolinite in Earth’s deep water cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Huijeong; Seoung, Donghoon; Lee, Yongjae

Water is the most abundant volatile component in the Earth. It continuously enters the mantle through subduction zones, where it reduces the melting temperature of rocks to generate magmas. The dehydration process in subduction zones, which determines whether water is released from the slab or transported into the deeper mantle, is an essential component of the deep water cycle. Here in this paper we use in situ and time-resolved high-pressure/high-temperature synchrotron X-ray diffraction and infrared spectra to characterize the structural and chemical changes of the clay mineral kaolinite. At conditions corresponding to a depth of about 75 km in amore » cold subducting slab (2.7 GPa and 200 °C), and in the presence of water, we observe the pressure-induced insertion of water into kaolinite. This super-hydrated phase has a unit cell volume that is about 31% larger, a density that is about 8.4% lower than the original kaolinite and, with 29 wt% H 2O, the highest water content of any known aluminosilicate mineral in the Earth. As pressure and temperature approach 19 GPa and about 800 °C, we observe the sequential breakdown of super-hydrated kaolinite. The formation and subsequent breakdown of super-hydrated kaolinite in cold slabs subducted below 200 km leads to the release of water that may affect seismicity and help fuel arc volcanism at the surface.« less

A role for subducted super-hydrated kaolinite in Earth’s deep water cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Huijeong; Seoung, Donghoon; Lee, Yongjae

Water is the most abundant volatile component in the Earth. It continuously enters the mantle through subduction zones, where it reduces the melting temperature of rocks to generate magmas. The dehydration process in subduction zones, which determines whether water is released from the slab or transported into the deeper mantle, is an essential component of the deep water cycle. Here we use in situ and time-resolved high-pressure/high-temperature synchrotron X-ray diffraction and infrared spectra to characterize the structural and chemical changes of the clay mineral kaolinite. At conditions corresponding to a depth of about 75 km in a cold subducting slabmore » (2.7 GPa and 200 °C), and in the presence of water, we observe the pressure-induced insertion of water into kaolinite. This super-hydrated phase has a unit cell volume that is about 31% larger, a density that is about 8.4% lower than the original kaolinite and, with 29 wt% H2O, the highest water content of any known aluminosilicate mineral in the Earth. As pressure and temperature approach 19 GPa and about 800 °C, we observe the sequential breakdown of super-hydrated kaolinite. The formation and subsequent breakdown of super-hydrated kaolinite in cold slabs subducted below 200 km leads to the release of water that may affect seismicity and help fuel arc volcanism at the surface.« less

Factors involved in the cytotoxicity of kaolinite towards macrophages in vitro.

PubMed Central

Davies, R

1983-01-01

The cytotoxicity of a high purity Cornish kaolinite toward mouse peritoneal macrophages in vitro was examined. The material was cytotoxic towards these cells, the activity could be decreased substantially by pretreating the dust with poly(2-vinylpyridine N-oxide). Pretreatment of the dusts with poly(acrylic acid) had a small effect on cytotoxicity, but combinations of the polymer treatments virtually abolished the material's biological activity towards macrophages. These studies indicated that the cytotoxicity of kaolinite is not due to its flakelike morphology. Images FIGURE 1. PMID:6641658

INTERACTIONS BETWEEN CESIUM AND DISPERSED KAOLINITE POWDERS AT HIGH TEMPERATURES FOR TREATMENT OF MIXED WASTES

EPA Science Inventory

Kaolinite sorbents were found to manage emissions of vapor phase cesium, when the kaolinite was injected into the combustor, having maximum value between 1400 and 1500 K. The mechanism of this process and its quantification await further research.

Synthesis of kaolinite-filled EPDM rubber composites by solution intercalation: structural characterization and studies on mechanical properties

NASA Astrophysics Data System (ADS)

Ginil Mon, S.; Jaya Vinse Ruban, Y.; Vetha Roy, D.

2011-09-01

In the large field of nanotechnology, polymer matrix-based nanocomposites have become a prominent area of current research and development. Exfoliated clay-based nanocomposites have dominated the polymer world with excellent characteristics. EPDM rubber composites have been synthesized by solution-intercalation using the easily available kaolinite as filler. The composite structure has been elucidated by X-ray diffraction (XRD), Fourier transform IR, and scanning electron microscope studies. The molecular level dispersion of clay layers has been verified by the disappearance of basal XRD peak of kaolinite in the EPDM/kaolinite composites. The mechanical properties showed significant improvement of EPDM/kaolinite composites with respect to neat EPDM.

Characterization and Applications of Kaolinite Robustly Grafted by an Ionic Liquid with Naphthyl Functionality

PubMed Central

Detellier, Christian

2017-01-01

Functionalization of the kaolinite (K) interlayer space is challenging. In this work, a new kaolinite-based nanohybridmaterial (K-NI) was successfully synthesized by grafting on the interlayer aluminol surfaces the ionic liquid, 1-(1-methylnaphthyl)-3-(2-hydroxyethyl) imidazolium chloride (NI), using a guest displacement strategy. A substantial increase of the basal spacing (10.8 Å) was obtained. This is a grafted derivative of kaolinite possessing one of the largest d-values. Washing in water for several days and other vigorous treatments such as sonication showed a minor effect on the integrity of the material. FTIR and 13C NMR confirmed the conservation of the structure of the ionic liquid after the grafting. Thermal analysis confirmed the presence of grafted material and was used to estimate the abundance of the grafted ionic liquid (0.44 mole per mole of kaolinite structural formula, (Al2Si2O5(OH)4)). By using cyclic voltammetry, the permeability of a film of K-NI for the bulky ferricyanide ions was demonstrated. The accumulation of nitrophenolate anions was effective (maximum capacity of 190 μmol/g), but was less important than what was expected due to the steric hindrance of the bulky grafted NI. Although the presence of chloride anions reduced the adsorption capacity, the affinity of the modified kaolinite interlayer space for the nitrophenolate anions was demonstrated. PMID:28850087

Characterization and Applications of Kaolinite Robustly Grafted by an Ionic Liquid with Naphthyl Functionality.

PubMed

Kenne Dedzo, Gustave; Detellier, Christian

2017-08-29

Functionalization of the kaolinite (K) interlayer space is challenging. In this work, a new kaolinite-based nanohybridmaterial (K-NI) was successfully synthesized by grafting on the interlayer aluminol surfaces the ionic liquid, 1-(1-methylnaphthyl)-3-(2-hydroxyethyl) imidazolium chloride (NI), using a guest displacement strategy. A substantial increase of the basal spacing (10.8 Å) was obtained. This is a grafted derivative of kaolinite possessing one of the largest d -values. Washing in water for several days and other vigorous treatments such as sonication showed a minor effect on the integrity of the material. FTIR and 13 C NMR confirmed the conservation of the structure of the ionic liquid after the grafting. Thermal analysis confirmed the presence of grafted material and was used to estimate the abundance of the grafted ionic liquid (0.44 mole per mole of kaolinite structural formula, (Al₂Si₂O₅(OH)₄)). By using cyclic voltammetry, the permeability of a film of K-NI for the bulky ferricyanide ions was demonstrated. The accumulation of nitrophenolate anions was effective (maximum capacity of 190 μmol/g), but was less important than what was expected due to the steric hindrance of the bulky grafted NI. Although the presence of chloride anions reduced the adsorption capacity, the affinity of the modified kaolinite interlayer space for the nitrophenolate anions was demonstrated.

Coagulation of bitumen with kaolinite in aqueous solutions containing Ca2+, Mg2+ and Fe3+: effect of citric acid.

PubMed

Gan, Weibing; Liu, Qi

2008-08-01

Heterocoagulation experiments of kaolinite with solvent-diluted-bitumen were carried out to investigate the effect of hydrolyzable metal cations and citric acid on the liberation of bitumen from kaolinite. The adsorption of Ca(2+) and Mg(2+) on kaolinite, and zeta potentials of kaolinite and bitumen droplets in solutions containing 10(-3)mol/L of Ca(2+), Mg(2+) and Fe(3+) with or without citric acid were also measured. It was found that the heterocoagulation of bitumen with kaolinite was enhanced in the presence of the metal cations from pH 7 to pH 10.5, accompanied by a decrease in the magnitude of the zeta potentials and an increase in the adsorption of the metal cations on kaolinite and possibly on bitumen droplets. The addition of 5 x 10(-4)mol/L citric acid reduced the degree of coagulation from 90% to less than 40% in the presence of 10(-3)mol/L Ca(2+) and Mg(2+) cations at pH approximately 10, and at pH approximately 8 for Fe(3+). It was found that hydrolyzable metal cations enhanced bitumen-kaolinite interactions through electrical double layer compression and specific adsorption of the metal hydrolysis species on the surface of kaolinite. The effect of metal cations was removed by citric acid through formation of metal-citrate complexes and/or the adsorption of citrate anions, which restored the zeta potentials of both kaolinite and bitumen. Therefore, electrostatic attraction or repulsion was responsible for the coagulation or dispersion of kaolinite particles from bitumen droplets in the tested system.

Mineralogical and hydrochemical effects on adsorption removal of cesium-137 and strontium-90 by kaolinite.

PubMed

Jeong, C H

2001-01-01

Adsorption characteristics of the nuclides onto kaolinite were investigated by batch experiment under various pH conditions and concentrations of groundwater cations (Ca2+, Mg2+, K+ and Na+) and anions (HCO3-, CO3(2-) and SO4(2-). Adsorption removal of 137Cs and 90Sr by kaolinite greatly increased as the concentration of groundwater cations increased from 10(-5) to 10(-1) M. In contrast, the pH exerted a small effect on the adsorption of 137Cs and 90Sr onto kaolinite. The zeta potential of kaolinite particles showed a negative increase of amphoteric surface charge with increasing pH. The adsorption behavior of 90Sr was also highly dependent on the concentration of bicarbonate. The thermodynamic saturation index indicated that bicarbonate exerts great effect on strontium adsorption by the precipitation of a strontianite (SrCO3) and a change in pH.

Roles of functional groups of naproxen in its sorption to kaolinite.

PubMed

Yu, Chenglong; Bi, Erping

2015-11-01

The sorption of acidic anti-inflammatory drugs to soils is important for evaluating their fate and transformations in the water-soil environment. However, roles of functional groups of ionisable drugs onto mineral surfaces have not been sufficiently studied. In this study, batch experiments of naproxen (NPX, anti-inflammatory drug) and two kinds of competitors to kaolinite were studied. The Kd of naproxen to kaolinite is 1.30-1.62 L kg(-1). The n-π electron donor-acceptor (n-π EDA) interaction between diaromatic ring of naproxen (π-electron acceptors) and the siloxane oxygens (n-donors) of kaolinite is the dominant sorption mechanism. The carboxyl group of naproxen can contribute to the overall sorption. A conception model was put forward to elucidate to sorption mechanisms, in which the contribution of n-π EDA and hydrogen bond to overall sorption was quantified. These sorption mechanisms can be helpful for estimating the fate and mobility of acid pharmaceuticals in soil-water environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

A systematic investigation into the extraction of aluminum from coal spoil through kaolinite.

PubMed

Qiao, X C; Si, P; Yu, J G

2008-11-15

This research has applied kaolin and active carbon (AC) to the investigation of the recovery of aluminum from coal spoil (CS). The kaolin, AC-containing kaolin mixture, and CS have been calcined at 500, 600, 700, 800, and 900 degrees C for 15, 30, 60, and 120 min. The transformation of kaolinite and aluminum extraction that occurred in each calcined sample have been characterized using XRD, TG, IR, and hydrochloric acid leaching methods. The dehydroxylation of kaolinite and the decomposition of metakaolin were influenced by thermal treatment temperature and time. The metakaolin had kept a portion of OH- in its structure until it was calcined at a temperature of 800 degrees C. Under 60 min treatment, new SiO2 phase was able to be formed at 500 degrees C, kaolinite was totally converted to metakaolin at 600 degrees C, and the SiO2 rejoined the reaction at 800 degrees C. The decompositions of CS were similar to those of kaolin mixture containing 20 wt % AC (MKC). The combustion of combustible matter accelerated the decomposition of kaolinite in the CS and MKC. Higher AC content led to lower aluminum extraction. The treatment at 600 degrees C was optimal for both CS and MKC.

Interaction of human adenoviruses and coliphages with kaolinite and bentonite.

PubMed

Bellou, Maria I; Syngouna, Vasiliki I; Tselepi, Maria A; Kokkinos, Petros A; Paparrodopoulos, Spyros C; Vantarakis, Apostolos; Chrysikopoulos, Constantinos V

2015-06-01

Human adenoviruses (hAdVs) are pathogenic viruses responsible for public health problems worldwide. They have also been used as viral indicators in environmental systems. Coliphages (e.g., MS2, ΦX174) have also been studied as indicators of viral pollution in fecally contaminated water. Our objective was to evaluate the distribution of three viral fecal indicators (hAdVs, MS2, and ΦΧ174), between two different phyllosilicate clays (kaolinite and bentonite) and the aqueous phase. A series of static and dynamic experiments were conducted under two different temperatures (4, 25°C) for a time period of seven days. HAdV adsorption was examined in DNase I reaction buffer (pH=7.6, and ionic strength (IS)=1.4mM), whereas coliphage adsorption in phosphate buffered saline solution (pH=7, IS=2mM). Moreover, the effect of IS on hAdV adsorption under static conditions was evaluated. The adsorption of hAdV was assessed by real-time PCR and its infectivity was tested by cultivation methods. The coliphages MS2 and ΦΧ174 were assayed by the double-layer overlay method. The experimental results have shown that coliphage adsorption onto both kaolinite and bentonite was higher for the dynamic than the static experiments; whereas hAdV adsorption was lower under dynamic conditions. The adsorption of hAdV increased with decreasing temperature, contrary to the results obtained for the coliphages. This study examines the combined effect of temperature, agitation, clay type, and IS on hAdV adsorption onto clays. The results provide useful new information on the effective removal of viral fecal indicators (MS2, ΦX174 and hAdV) from dilute aqueous solutions by adsorption onto kaolinite and bentonite. Factors enabling enteric viruses to penetrate soils, groundwater and travel long distances within aquifers are important public health issues. Because the observed adsorption behavior of surrogate coliphages MS2 and ΦΧ174 is substantially different to that of hAdV, neither MS2 nor �

Differential regulation of phenanthrene biodegradation process by kaolinite and quartz and the underlying mechanism.

PubMed

Gong, Beini; Wu, Pingxiao; Ruan, Bo; Zhang, Yating; Lai, Xiaolin; Yu, Langfeng; Li, Yongtao; Dang, Zhi

2018-05-05

Natural and cost-effective materials such as minerals can serve as supportive matrices to enhance biodegradation of polycyclic aromatic hydrocarbons (PAHs). In this study we evaluated and compared the regulatory role of two common soil minerals, i.e. kaolinite and quartz in phenanthrene (a model PAH) degradation by a PAH degrader Sphingomonas sp. GY2B and investigated the underlying mechanism. Overall kaolinite was more effective than quartz in promoting phenanthrene degradation and bacterial growth. And it was revealed that a more intimate association was established between GY2B and kaolinite. Si and O atoms on mineral surface were demonstrated to be involved in GY2B-mineral interaction. There was an higher polysaccharide/lipid content in the EPS (extracellular polymeric substances) secreted by GY2B on kaolinite than on quartz. Altogether, these results showed that differential bacterial growth, enzymatic activity, EPS composition as well as the interface interaction may explain the effects minerals have on PAH biodegradation. It was implicated that different interface interaction between different minerals and bacteria can affect microbial behavior, which ultimately results in different biodegradation efficiency. Copyright © 2018 Elsevier B.V. All rights reserved.

Influence of Kaolinite Clay Supplementation on Growth Performance and Digestive Function in Finishing Calf-fed Holstein Steers

PubMed Central

Ortiz, José; Montaño, Martín; Plascencia, Alejandro; Salinas, Jaime; Torrentera, Noemí; Zinn, Richard A.

2016-01-01

Two experiments were conducted to examine the influence of kaolinite clay supplementation (0%, 1%, or 2% diet dry matter [DM] basis) on characteristics of digestion (Trial 1) and growth performance (Trial 2) in calf-fed Holstein steers fed a finishing diet. In Trial 1, 6 Holstein steers (539±15 kg) with ruminal and duodenal cannulas were used to evaluate treatment effects on characteristics of digestion. Kaolinite clay supplementation decreased total tract DM digestion (linear effect, p<0.01) without effects (p≥0.10) on site and extent of digestion of organic matter, neutral detergent fiber, starch and N, or ruminal microbial efficiency. There were no treatment effects on ruminal pH, volatile fatty acids molar proportions or estimated methane production. In Trial 2, 108 Holstein steers (132.4±5.6 kg) were used in a 308-d study to evaluate growth performance and carcass characteristics. There were no treatment effects (p>0.10) on average daily gain (ADG) and gain efficiency (ADG/dry matter intake). Kaolinite supplementation tended (linear effect, p = 0.08) to increase dietary net energy (NE) during the initial 112-d period. However, the overall (308-d) effect of supplementation dietary NE was not appreciable (p>0.20). However, due to the inertness of kaolinite, itself, the ratio of observed-to-expected dietary NE increased with kaolinite supplementation. This effect was more pronounced (linear effect, p 0.03) during the initial 224 d of the study. Overall (308 d), kaolinite supplementation tended to increase (linear effect, p = 0.07) dietary NE by 3% over expected. Kaolinite supplementation did not affect carcass weight, yield grade, longissimus area, kidney, pelvic and heart fat, and quality grade, but decreased (linear effect, p = 0.01) dressing percentage. It is concluded that kaolinite supplementation up to 2% of diet DM may enhance energetic efficiency of calf-fed Holstein steers in a manner independent of changes in characteristics of ruminal and total

Effect of processing route for preparation of mullite from kaolinite and alumina

NASA Astrophysics Data System (ADS)

Behera, Pallavi Suhasinee; Bhattacharyya, Sunipa

2018-05-01

In current work, two different types of mullite ceramic powder were prepared using kaolinite and alumina by solid state and chemical precipitation route. The phases, bond types and microstructural evolution of the mullite powders were investigated by X-ray diffraction, infrared analysis, and field emission scanning electron microscopy to study the mullitisation behavior. The solid state method evident a pure mullite phase formation at 1550 °C. In case of chemical precipitation route small amount of alumina peak was noticed along with major phase of mullite which was also clearly apprehended from FESEM micrographs and IR spectra. Densification was more for the samples prepared by solid state process which may be correlated to the delayed mullitization process in chemical precipitation route.

Role of background ions in guar gum adsorption on oxide minerals and kaolinite.

PubMed

Ma, Xiaodong; Pawlik, Marek

2007-09-15

Adsorption of guar gum onto alumina, titania (rutile), hematite, quartz, and kaolinite was investigated as a function of pH, ionic strength (from distilled water to saturated NaCl and KCl), and the type of background electrolyte (0.01 mol/L LiCl, NaCl, KCl, and CsCl). It was demonstrated that the adsorption density of the polymer does not depend on pH for any of the tested minerals, so only hydrogen bonding was identified as the dominant adsorption mechanism. The minerals could, however, be divided into two groups depending on the effect of the salt type on polymer adsorption. Guar gum adsorption onto quartz and kaolinite significantly increased in the presence of even a small amount of KCl, while NaCl equally enhanced guar gum adsorption on these two minerals only at concentrations approaching saturation. In contrast, no significant differences between the effects of KCl and NaCl on polysaccharide adsorption were observed on titania, alumina, and hematite. The results were correlated with the chaotropic (KCl) and kosmotropic (NaCl) properties of the background salts, and-based on a review of the available literature data-with the presence (quartz) or absence (titania, alumina, hematite) of an extensive hydration layer on the oxide surfaces. It was concluded that the main role of background ions in the studied systems was to control the stability of the interfacial water layer on oxide particles whose presence serves as a barrier to guar gum adsorption.

Surface complexation modeling of Cu(II) adsorption on mixtures of hydrous ferric oxide and kaolinite

PubMed Central

Lund, Tracy J; Koretsky, Carla M; Landry, Christopher J; Schaller, Melinda S; Das, Soumya

2008-01-01

Background The application of surface complexation models (SCMs) to natural sediments and soils is hindered by a lack of consistent models and data for large suites of metals and minerals of interest. Furthermore, the surface complexation approach has mostly been developed and tested for single solid systems. Few studies have extended the SCM approach to systems containing multiple solids. Results Cu adsorption was measured on pure hydrous ferric oxide (HFO), pure kaolinite (from two sources) and in systems containing mixtures of HFO and kaolinite over a wide range of pH, ionic strength, sorbate/sorbent ratios and, for the mixed solid systems, using a range of kaolinite/HFO ratios. Cu adsorption data measured for the HFO and kaolinite systems was used to derive diffuse layer surface complexation models (DLMs) describing Cu adsorption. Cu adsorption on HFO is reasonably well described using a 1-site or 2-site DLM. Adsorption of Cu on kaolinite could be described using a simple 1-site DLM with formation of a monodentate Cu complex on a variable charge surface site. However, for consistency with models derived for weaker sorbing cations, a 2-site DLM with a variable charge and a permanent charge site was also developed. Conclusion Component additivity predictions of speciation in mixed mineral systems based on DLM parameters derived for the pure mineral systems were in good agreement with measured data. Discrepancies between the model predictions and measured data were similar to those observed for the calibrated pure mineral systems. The results suggest that quantifying specific interactions between HFO and kaolinite in speciation models may not be necessary. However, before the component additivity approach can be applied to natural sediments and soils, the effects of aging must be further studied and methods must be developed to estimate reactive surface areas of solid constituents in natural samples. PMID:18783619

Modelling the structural controls of primary kaolinite formation

NASA Astrophysics Data System (ADS)

Tierney, R. L.; Glass, H. J.

2016-09-01

An abundance of kaolinite was formed within the St. Austell outcrop of the Cornubian batholith in Cornwall, southwest England, by the hydrous dissolution of feldspar crystals. The permeability of Cornish granites is low and alteration acts pervasively from discontinuity features, with montmorillonite recognised as an intermediate assemblage in partially kaolinised material. Structural features allowed fluids to channel through the impermeable granite and pervade deep into the rock. Areas of high structural control are hypothesised to link well with areas of advanced alteration. As kaolinisation results in a loss of competence, we present a method of utilising discontinuity orientations from nearby unaltered granites alongside the local tectonic history to calculate strain rates and delineate a discrete fracture network. Simulation of the discrete fracture network is demonstrated through a case study at Higher Moor, where kaolinite is actively extracted from a pit. Reconciliation of fracture connectivity and permeability against measured subsurface data show that higher values of modelled properties match with advanced kaolinisation observed in the field. This suggests that the technique may be applicable across various industries and disciplines.

Understanding the sorption mechanisms of aflatoxin B1 to kaolinite, illite, and smectite clays via a comparative computational study.

PubMed

Kang, Fuxing; Ge, Yangyang; Hu, Xiaojie; Goikavi, Caspar; Waigi, Michael Gatheru; Gao, Yanzheng; Ling, Wanting

2016-12-15

In current adsorption studies of biotoxins to phyllosilicate clays, multiply weak bonding types regarding these adsorptions are not well known; the major attractive forces, especially for kaolinite and illite, are difficult to be identified as compared to smectite with exchangeable cations. Here, we discriminated the bonding types of aflatoxin B1 (AFB1) contaminant to these clays by combined batch experiment with model computation, expounded their bonding mechanisms which have been not quantitatively described by researchers. The observed adsorbent-to-solution distribution coefficients (K d ) of AFB1 presented in increasing order of 18.5-37.1, 141.6-158.3, and 354.6-484.7L/kg for kaolinite, illite, and smectite, respectively. Normalization of adsorbent-specific surface areas showed that adsorption affinity of AFB1 is mainly dependent on the outside surfaces of clay aggregates. The model computation and test of ionic effect further suggested that weakly electrostatic attractions ((Si/Al-OH) 2 ⋯(OC) 2 ) are responsible for AFB1-kaolinite adsorption (K d , 18.5-37.1L/kg); a moderate electron-donor-acceptor attraction ((CO) 2 ⋯K + ⋯(O-Al) 3 ) is related to AFB1-illite adsorption (K d , 141.6-158.3L/kg); a strong calcium-bridging linkage ((CO) 2 ⋯Ca 2+ ⋯(O-Si) 4 ) is involved in AFB1-smectite adsorption (K d , 354.6-484.7L/kg). Changes in Gibbs free energy (ΔG°) suggested that the computed result is reliable, providing a good reproduction of AFB1-clay interaction. Copyright © 2016 Elsevier B.V. All rights reserved.

Kaolinite adsorption-regeneration system for dyestuff treatment by Fenton based processes.

PubMed

Rosales, Emilio; Anasie, Delia; Pazos, Marta; Lazar, Iuliana; Sanromán, M Angeles

2018-05-01

The regeneration and reuse of adsorbents is a subject of interest nowadays in order to reduce the pollution and the wastes generated in the adsorption wastewater treatment. In this work, the regeneration of the spent kaolinite by different advanced oxidation processes (Fenton, electro-Fenton and electrokinetic-Fenton) was evaluated. Initially, it was confirmed the ability of a low cost clayey material, kaolinite, for the adsorption of model dye such as Rhodamine B showing Freundlich isotherm fitting. Then, the regeneration and consequent degradation of the pollutant in the adsorbent by Fenton based processes was carried out. The role of different parameters affecting the regeneration process (H 2 O 2 :Fe 2+ ratio, liquid:solid ratio) were evaluated. Working at 100:1 H 2 O 2 :Fe 2+ ratio and 30min near complete dye removal (around 97%) from kaolinite was obtained by Fenton treatment. After that, a two-stage treatment for adsorption-regeneration was evaluated during five treatment cycles demonstrating its viability for regeneration of the adsorbent through dye degradation. Based on the successful application of Fenton technique, the improvement of the treatment by electro-Fenton and electrokinetic-Fenton were studied for different solid:liquid ratios achieving satisfactory regeneration values. Copyright © 2017 Elsevier B.V. All rights reserved.

Remediation and desorption kinetics of pyrene from kaolinite co-contaminated with heavy metals at various organic matter contents

NASA Astrophysics Data System (ADS)

Saeedi, Mohsen; Li, Loretta Y.; Grace, John R.

2017-04-01

Soils co-contaminated with polycyclic aromatic hydrocarbons (PAHs) and heavy metals are challenging for remediation. In the present study desorption of pyrene in kaolinite, co-contaminated by Ni, Pb and Zn, was examined by combinations of surfactants and chelating agents such as Triton X-100, Tween 80, Ethylene diamine tetra acetic acid (EDTA) and citric acid. Results showed that a combination of Triton X-100 (7.5 % w/w) + EDTA (0.01 M) and Tween 80 (7.5 % w/w) + EDTA (0.01 M) were effective in simultaneously desorbing both types of contaminants. Batch desorption tests were conducted using single and combined enhancing agents containing Triton X-100 and Tween 80 as non-ionic surfactants, EDTA as a chelating agent, and citric acid as an organic acid. The solution with the highest removal efficiency was the combined solution containing Triton X-100 (7.5 % w/w) + EDTA (0.01M). Triton X-100 (7.5% w/w) + EDTA (0.01M) led to removal efficiencies of 88% for pyrene in base kaolinite. Batch desorption kinetic experiments were performed using Triton X-100 (7.5% w/w) + EDTA (0.01M). During the first 24 h, desorption was rapid. Organic matter content in the kaolinite led to a reduction in the desorption rate of the contaminants. The desorption kinetic data were well fitted by a pseudo-second-order kinetic model.

Testing the stability of magnetic iron oxides/kaolinite nanocomposite under various pH conditions

NASA Astrophysics Data System (ADS)

Tokarčíková, Michaela; Tokarský, Jonáš; Kutláková, Kateřina Mamulová; Seidlerová, Jana

2017-09-01

Magnetically modified clays containing iron oxides nanoparticles (FexOy NPs) are low-cost and environmentally harmless materials suitable for sorption of pollutants from wastewaters. Stability of this smart material was evaluated both experimentally and theoretically using molecular modelling. Original kaolinite and prepared FexOy/kaolinite nanocomposite were characterized using X-ray fluorescence spectroscopy, X-ray powder diffraction, infrared spectroscopy, and transmission electron microscopy, and the stability was studied using leaching tests performed according to the European technical standard EN 12457-2 in deionized water and extraction agents with varying pH (2, 4, 9, and 11). The influence of pH on amount of FexOy NPs released from the composite and amount of the basic elements released from the kaolinite structure was studied using inductively coupled plasma atomic emission spectroscopy. All experiments proved that the magnetic properties of the nanocomposite will not change even after leaching in extraction agents with various pH.

Compressional Wave Speed and Absorption Measurements in a Saturated Kaolinite-Water Artificial Sediment.

DTIC Science & Technology

OCEAN BOTTOM, ULTRASONIC PROPERTIES), (*UNDERWATER SOUND, SOUND TRANSMISSION), KAOLINITE , ABSORPTION, COMPRESSIVE PROPERTIES, POROSITY, VELOCITY, VISCOELASTICITY, MATHEMATICAL MODELS, THESES, SEDIMENTATION

Chlorination of alumina in kaolinitic clay

NASA Astrophysics Data System (ADS)

Grob, B.; Richarz, W.

1984-09-01

The chlorination of alumina in kaolinitic clay with Cl2 and CO gas mixtures was studied gravimetrically. The effects of the calcination method and of NaCl addition on the reactivity of the clay were examined. Fast reaction rates were achieved only with samples previously exposed to a sulfating treatment. Optimum conditions, with maximum yield and selectivity to A1C13 and minimum SiO2 conversion, were found between 770 and 970 K. At higher temperatures the SiCl4 formed poisons the reactive alumina surface by selective chemisorption with a marked decrease of the reaction rate.

[Effects of algae and kaolinite particles on the survival of bacteriophage MS2].

PubMed

He, Qiang; Wu, Qing-Qing; Ma, Hong-Fang; Zhou, Zhen-Ming; Yuan, Bao-Ling

2014-08-01

In this study, Bacteriophage MS2, Kaolinite and Microcystis aeruginosa were selected as model materials for human enteric viruses, inorganic and organic particles, respectively. The influence of the inorganic (Kaolinite) or organic (Microcystis aeruginosa) particles on the survival of MS2 at different conditions, such as particles concentration, pH, ion concentration and natural organic matter (NOM) were studied. The results showed that Kaolinite had no effect on the survival of phage MS2 except that apparent survival of MS2 increased 1 logarithm in higher hardness water. Microcystis aeruginosa addition reduced 1 logarithm of MS2 survival. However, when the pH value was greater than 4.0 or the concentration of Microcystis aeruginosa was less than 1.0 x 10(6) cells x L(-1), Microcystis aeruginosa addition had no influence on the survival of MS2. In higher hardness water, Microcystis aeruginosa protected MS2 viruses and then increased the survival of MS2. In drinking water, resource containing higher concentration of particles, the survival ability of virus would be enhanced with the increase of the hardness and then elevated the risks of drinking water safety.

Preferential polymerization and adsorption of L-optical isomers of amino acids relative to D-optical isomers on kaolinite templates.

NASA Technical Reports Server (NTRS)

Jackson, T. A.

1971-01-01

Experiments on the polymerization of the L- and D-optical isomers of aspartic acid and serine using kaolinite as a catalyst showed that the L-optical isomers were polymerized at a much higher rate than the D-optical isomers; racemic (DL-) mixtures were polymerized at an intermediate rate. The peptides formed from the L-monomers were preferentially adsorbed by the clay. In the absence of kaolinite, no significant or consistent difference in the behavior of the L- and D-optical isomers was observed. In experiments on the adsorption of L- and D-phenylalanine by kaolinite, the L-optical isomer was preferentially adsorbed.

Kaolinite synthesis at 25°C

USGS Publications Warehouse

Hem, J.D.; Lind, Carol J.

1974-01-01

The addition of quercetin, an organic flavone (C15H10O7), to aqueous solutions containing silica and aluminum and adjusted to final pH's from 6.5 to 8.5 produced a 1 : 1 alumninosilicate precipitate which, after 6 to 16 months of aging in solution at 25°C, contained as much as 5 percent well-formed kaolinite plates. Similar solutions containing no organic material produced relatively amorphous precipitates with the same composition and stability (standard free energy of formation = -897±1 kilocalories per mole) but with substantially smaller amounts of crystaline material even after 2 years of aging.

Crystallization of aqueous ammonium sulfate particles internally mixed with soot and kaolinite: crystallization relative humidities and nucleation rates.

PubMed

Pant, Atul; Parsons, Matthew T; Bertram, Allan K

2006-07-20

Using optical microscopy, we investigated the crystallization of aqueous ammonium sulfate droplets containing soot and kaolinite, as well as the crystallization of aqueous ammonium sulfate droplets free of solid material. Our results show that soot did not influence the crystallization RH of aqueous ammonium sulfate particles under our experimental conditions. In contrast, kaolinite increased the crystallization RH of the aqueous ammonium sulfate droplets by approximately 10%. In addition, our results show that the crystallization RH of aqueous ammonium sulfate droplets free of solid material does not depend strongly on particle size. This is consistent with conclusions made previously in the literature, based on comparisons of results from different laboratories. From the crystallization results we determined the homogeneous nucleation rates of crystalline ammonium sulfate in aqueous ammonium sulfate droplets and the heterogeneous nucleation rates of crystalline ammonium sulfate in aqueous ammonium sulfate particles containing kaolinite. Using classical nucleation theory and our experimental data, we determined that the interfacial tension between an ammonium sulfate critical nucleus and an aqueous ammonium sulfate solution is 0.064 +/- 0.003 J m(-2) (in agreement with our previous measurements), and the contact angle between an ammonium sulfate critical nucleus and a kaolinite surface is 59 +/- 2 degrees. On the basis of our results, we argue that soot will not influence the crystallization RH of aqueous ammonium sulfate droplets in the atmosphere, but kaolinite can significantly modify the crystallization RH of atmospheric ammonium sulfate droplets. As an example, the CRH50 (the relative humidity at which 50% of the droplets crystallize) ranges from about 41 to 51% RH when the diameter of the kaolinite inclusion ranges from 0.1 to 5 microm. For comparison, the CRH50 of aqueous ammonium sulfate droplets (0.5 microm diameter) free of solid material is

High temperature ablation of kaolinite layered silicate/phenolic resin/asbestos cloth nanocomposite.

PubMed

Bahramian, Ahmad Reza; Kokabi, Mehrdad; Famili, Mohammad Hossein Navid; Beheshty, Mohammad Hossein

2008-01-15

The successful return of re-entry space vehicle, which is subjected to severe aerodynamic heating, is largely accompanied by some provisions to reduce the heat transfer to the structure. Heat shield is the best protection means which undergoes physical, chemical, and mostly endothermal transformations. The objective of this work is to investigate the ablating, charring, and thermal degradation behaviour of heat shield resol-type phenolic resin/kaolinite/asbestos cloth nanocomposite by oxyacetylene flame test with an external heat flux of 8 x 10(9)W/m(2) and 3000 K hot gas temperature and thermal analyzer techniques. Kinetic parameters of thermal degradation and temperature distribution at the back surface of the nanocomposite heat shield were determined and compared with that of composite counterpart.

HIGH TEMPERATURE SORPTION OF CESIUM AND STRONTIUM ON DISPERSED KAOLINITE POWDERS

EPA Science Inventory

Sorption of cesium and strontium on kaolinite powders was investigated as a means to minimize the emissions of these metals during certain high-temperature processes currently being developed to isolate and dispose of radiological and mixed wastes. In this work, nonradioactive aq...

Spectroscopic studies of U(VI) sorption at the kaolinite-water interface. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, H.A.; Parks, G.A.; Brown, G.E. Jr.

Efficient use of U as a resource and safe handling, recycling and disposal of U-containing wastes require an understanding of the factors controlling the fate of U, where fate refers to the destination of U, typically expressed as an environmental medium or a process phase. The sorption process constitutes a change in elemental fate. Partitioning of an element from solution to a solid phase, or sorption, can be divided into three broad categories: adsorption, surface precipitation, and absorption. Extended X-ray absorption fine structure (EXAFS), a type of X-ray absorption spectroscopy (XAS), offers the possibility for distinguishing among different modes ofmore » sorption by characterizing the atomic environment of the sorbing element. In this study, the authors use EXAFS to determine the structure of U(VI) sorption complexes at the kaolinite-water interface. In Chapter One, they present an overview of selected aspects of U structural chemistry as a basis for considering the structural environment of U at the solid-water interface. To evaluate the utility of XAS for characterization of the structural environment of U(VI) at the solid-water interface, they have carried out an in-depth analysis of XAS data from U(VI)-containing solid and solution model compounds, which they describe in Chapter Two. In Chapter three, they consider sorption of U by kaolinite as a means of effecting the removal of U from surface collection pond waters on the Rocky Flats Plant site in northern Colorado.« less

MOLECULAR DYNAMICS MODELING OF SORPTION OF PESTICIDES ONTO THE SURFACES OF KAOLINITE

EPA Science Inventory

To accurately predict the fate of contaminants in the environment and to make sound decisions about environmental remediation, we must accurately understand sorption mechanisms and surface reactivity of environmental particles. Sorption of selected pesticides on kaolinite surface...

Dispersion of kaolinite by dissolved organic matter from Douglas-fir roots

Treesearch

Philip B. Durgin; Jesse G. Chaney

1984-01-01

The organic constituents of water extracts from Douglas-fir (Pseudotsuga menziesii [Mirb.] Franco var. menziesii) roots that cause kaolinite dispersion were investigated. The dissolved organic matter was fractionated according to molecular size and chemical characteristics into acids, neutrals, and bases of the hydrophilic and hydrophobic groups.

Metal stabilization mechanism of incorporating lead-bearing sludge in kaolinite-based ceramics.

PubMed

Lu, Xingwen; Shih, Kaimin

2012-02-01

The feasibility and mechanism of incorporating simulated lead-laden sludge into low-cost ceramic products was investigated by observing the reaction of lead with two kaolinite-based precursors under sintering conditions. To investigate the phase transformation process of lead, lead oxide (PbO) mixed with a kaolinite or mullite precursor were fired at 500-950°C for 3h. Detailed X-ray diffraction analysis of sintered products revealed that both precursors had crystallochemically incorporated lead into the lead feldspar (PbAl(2)Si(2)O(8)) crystalline structure. By mixing lead oxide with kaolinite, lead feldspar begins to crystallize at 700°C; maximum incorporation of lead into this structure occurred at 950°C. However, two intermediate phases, Pb(4)Al(4)Si(3)O(16) and a polymorph of lead feldspar, were detected at temperatures between 700 and 900°C. By sintering lead oxide with the mullite precursor, lead feldspar was detected at temperatures above 750°C, and an intermediate phase of Pb(4)Al(4)Si(3)O(16) was observed in the temperature range of 750-900°C. This study compared the lead leachabilities of PbO and lead feldspar using a prolonged leaching test (at pH 2.9 for 23d) modified from the toxicity characteristic leaching procedure. The results indicate the superiority of lead feldspar in stabilizing lead and suggest a promising and reliable strategy to stabilize lead in ceramic products. Copyright © 2011 Elsevier Ltd. All rights reserved.

Dating Amazonian laterites through the novel geochronometers kaolinite and iron oxides

NASA Astrophysics Data System (ADS)

Allard, Thierry; Bressan Riffel, Silvana; Gautheron, Cécile; Fernandes Soares, Bruna; Pinna-Jamme, Rosella; Morin, Guillaume

2016-04-01

Soils on Earth's surface are in constant interaction with climate. As a matter of fact, soils cannot only produce greenhouse effect gases, such as NO2 and CH4, but also behave as sinks for CO2, especially by silicate weathering. Major processes of silicate weathering are known and exhibit climatic zonation at the global scale. Laterites are particularly relevant because they are ancient and deeply weathered soils of major significance. They occupy 30 % of the continental surface and can keep records of past climates and landscape modifications (paleosurface) through specific mineral markers. These formations reach several tens of meters and are mainly composed of kaolinite, iron and aluminium oxides as well as relicts of parent minerals such as quartz and ancillary minerals. Once the major processes of laterite formation are known, their age will allow a growth of researches, owing to the implementation of various chronometers. Moreover, it is fundamental to date laterites in order to improve our understanding of soil formation related to paleoclimates, and to build predictive models of their evolution. In this study, we focus on comparing kaolinite ages with the still unknown ages of lateritic duricrusts from the central Amazon region (Brazil), where strong weathering processes were developed from the early Tertiary, after the Andean uplift. The central Amazon region displays flat areas and dissected plateaus (100-180 m a.s.l.) sustained by weathered clastic sedimentary rocks and latosols. The region contains horizons of duricrusts, relatively continuous layers of Fe-cuirasses, stratified lateritic profiles, and kaolin deposits. Here we employed two methods to date ubiquitous secondary minerals of laterite, which are consistent with geological time-scale. The corresponding geochronometers are the following: (i) radiation-induced defects in kaolinite (trapped in duricrusts) analysed by electron paramagnetic resonance spectroscopy (EPR) (Balan et al., 2005), and (ii

Application of Brazilian kaolinite clay as adsorbent to removal of U(VI) from aqueous solution: Kinetic and thermodynamic of cation-basic interactions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guerra, Denis L., E-mail: denis@cpd.ufmt.b; Leidens, Victor L.; Viana, Rubia R.

2010-05-15

The compound N{sup 1}-[3-(trimethoxysilyl)propyl]diethylenetriamine was anchored onto Amazon kaolinite surface by heterogeneous route. The modified and natural kaolinite samples were characterized by transmission electron microscopy, scanning electron microscopic, X-ray diffraction, and nuclear magnetic nuclei of {sup 29}Si and {sup 13}C. The well-defined peaks obtained in the {sup 13}C NMR spectrum in the 5.0-62.1 ppm region confirmed the attachment of organic functional groups as pendant chains bonded into the porous clay. The ability of these materials to remove U(VI) from aqueous solution was followed by a series of adsorption isotherms adjusted to a Sips equation at room temperature and pH 4.0.more » The kinetic parameters analyzed by the Lagergren and Elovich models gave a good fit for a pseudo-second order reaction with k{sub 2} values 16.0 and 25.1 mmol g{sup -1} min{sup -1} ranges for natural and modified kaolinite clays, respectively. The energetic effects caused by metal ion adsorption were determined through calorimetric titrations. - Graphical abstract: This investigation reports the use of original and modified kaolinites as alternative absorbents. The compound N-[3-trimethoxysilyl)propyl]diethylenetriamine was anchored onto Amazon kaolinite surface by heterogeneous route.« less

Sorption of triclosan onto activated carbon, kaolinite and montmorillonite: effects of pH, ionic strength, and humic acid.

PubMed

Behera, Shishir Kumar; Oh, Seok-Young; Park, Hung-Suck

2010-07-15

Sorption of triclosan on three sorbents, viz., activated carbon, kaolinite and montmorillonite was studied as a function of pH, ionic strength and humic acid (HA) concentration through controlled batch experiments. Triclosan sorption was found to be higher in the acidic pH range, as varying pH showed significant influence on the surface charge of the sorbents and degree of ionization of the sorbate. Sorption capacity of the sorbents increased with an increase in the ionic strength of solution. At low pH (pH 3), the overall increase in triclosan sorption was 1.2, approximately 4 and 3.5 times, respectively for activated carbon, kaolinite and montmorillonite when ionic strength was increased from 1x10(-3) to 5x10(-1) M. Triclosan sorption onto activated carbon decreased from 31.4 to 10.6 mg g(-1) by increasing the HA concentration to 200 mg C L(-1). However, during sorption onto kaolinite and montmorillonite, the effect of HA was very complex probably due to (i) hydrophobicity (log K(ow)=4.76) of triclosan; and (ii) complexation of HA with triclosan. Though triclosan sorption onto activated carbon is higher, the potential of kaolinite and montmorillonite in controlling the transport of triclosan in subsurface environment can still be appreciable. 2010 Elsevier B.V. All rights reserved.

Radiation-Induced Defects in Kaolinite as Tracers of Past Occurrence of Radionuclides in a Natural Analogue of High Level Nuclear Waste Repository

NASA Astrophysics Data System (ADS)

Allard, T.; Fourdrin, C.; Calas, G.

2007-05-01

Understanding the processes controlling migrations of radioelements at the Earth's surface is an important issue for the long-term safety assessment of high level nuclear waste repositories (HLNWR). Evidence of past occurrence and transfer of radionuclides can be found using radiation-induced defects in minerals. Clay minerals are particularly relevant because of their widespread occurrence at the Earth's surface and their finely divided nature which provides high contact area with radioactive fluids. Owing to its sensitivity to radiations, kaolinite can be used as natural, in situ dosimeter. Kaolinite is known to contain radiation-induced defects which are detected by Electron Paramagnetic Resonance. They are differentiated by their nature, their production kinetics and their thermal stability. One of these defects is stable at the scale of geological periods and provides a record of past radionuclide occurrence. Based on artificial irradiations, a methodology has been subsequently proposed to determine paleodose cumulated by kaolinite since its formation. The paleodose can be used to derive equivalent radioelement concentrations, provided that the age of kaolinite formation can be constrained. This allows quantitative reconstruction of past transfers of radioelements in natural systems. An example is given for the Nopal I U-deposit (Chihuahua, Mexico), hosted in hydrothermally altered volcanic tufs and considered as analogue of the Yucca Mountain site. The paleodoses experienced by kaolinites were determined from the concentration of defects and dosimetry parameters of experimental irradiations. Using few geochemical assumption, a equivalent U-content responsible for defects in kaolinite was calculated from the paleodose, a dose rate balance and model ages of kaolinites constrained by tectonic phases. In a former study, the ages were assumptions derived from regional tectonic events. In thepresent study, ages of mineralization events are measured from U

Surface complexation model for multisite adsorption of copper(II) onto kaolinite

NASA Astrophysics Data System (ADS)

Peacock, Caroline L.; Sherman, David M.

2005-08-01

We measured the adsorption of Cu(II) onto kaolinite from pH 3-7 at constant ionic strength. EXAFS spectra show that Cu(II) adsorbs as (CuO 4H n) n-6 and binuclear (Cu 2O 6H n) n-8 inner-sphere complexes on variable-charge ≡AlOH sites and as Cu 2+ on ion exchangeable ≡X-H + sites. Sorption isotherms and EXAFS spectra show that surface precipitates have not formed at least up to pH 6.5. Inner-sphere complexes are bound to the kaolinite surface by corner-sharing with two or three edge-sharing Al(O,OH) 6 polyhedra. Our interpretation of the EXAFS data are supported by ab initio (density functional theory) geometries of analog clusters simulating Cu complexes on the {110} and {010} crystal edges and at the ditrigonal cavity sites on the {001}. Having identified the bidentate (≡AlOH) 2Cu(OH) 20, tridentate (≡Al 3O(OH) 2)Cu 2(OH) 30 and ≡X-Cu 2+ surface complexes, the experimental copper(II) adsorption data can be fit to the reactions

The immersion freezing behavior of size-segregated soot and kaolinite particles

NASA Astrophysics Data System (ADS)

Hartmann, S.; Augustin, S.; Clauss, T.; Niedermeier, D.; Raddatz, M.; Wex, H.; Shaw, R. A.; Stratmann, F.

2011-12-01

Heterogeneous ice nucleation plays a crucial role for ice formation in mixed-phase and cirrus clouds and has an important impact on precipitation formation, global radiation balances, and therefore Earth's climate (Cantrell and Heymsfield, 2005). Mineral dust and soot particles are found to be a major component of ice crystal residues (e.g., Pratt et al., 2009) so these substances are potential sources of atmospheric ice nuclei (IN). Experimental studies investigating the immersion freezing behavior of size-segregated soot and kaolinite particles conducted at the Leipzig Aerosol Cloud Interaction Simulator (LACIS) are presented. In our measurements only one aerosol particle is immersed in an air suspended water droplet which can trigger ice nucleation. The method facilitates very precise examinations with respect to temperature, ice nucleation time and ice nucleus size. Considering laboratory studies, the picture of the IN ability of soot particles is quite heterogeneous. Our studies show that submicron flame, spark soot particles and optionally coated with sulfuric acid to simulate chemically aging do not act as IN at temperatures higher than homogeneous freezing taking place. Therefore soot particles might not be an important source of IN for immersion freezing in the atmosphere. In contrast, kaolinite being representative for natural mineral dust with a well known composition and structure is found to be very active in forming ice for all freezing modes (e.g., Mason and Maybank, 1958). Analyzing the immersion freezing behavior of different sized kaolinite particles (300, 500 and 700 nm in diameter) the size effect was clearly observed, i.e. the ice fraction (number of frozen droplets per total number) scales with particle surface, i.e. the larger the ice nucleus surface the higher the ice fraction. The slope of the logarithm of the ice fraction as function of temperature is similar for all particle sizes investigated and fits very well with the results of L�

Amazon kaolinite functionalized with diethylenetriamine moieties for U(VI) removal: thermodynamic of cation-basic interactions.

PubMed

Guerra, Denis L; Leidens, Victor L; Viana, Rúbia R; Airoldi, Claudio

2010-08-15

The compound N-[3-(trimethoxysilyl)propyl]diethylenetriamine (MPDET) was anchored onto Amazon kaolinite surface (KLT) by heterogeneous route. The modified and natural kaolinite clay samples were characterized by transmission electron microscopy (TEM), scanning electron microscopic (SEM), N(2) adsorption, powder X-ray diffraction, thermal analysis, ion exchange capacities, and nuclear magnetic nuclei of (29)Si and (13)C. The well-defined peaks obtained in the (13)C NMR spectrum in the 5.0-62.1 ppm region confirmed the attachment of organic functional groups as pendant chains bonded into the porous clay. The adsorption of uranyl on natural (KLT) and modified (KLT(MPDET)) kaolinite clays was investigated as a function of the solution pH, metal concentration, temperature, and ionic strength. The ability of these materials to remove U(VI) from aqueous solution was followed by a series of adsorption isotherms adjusted to a Sips equation at room temperature and pH 4.0. The maximum number of moles adsorbed was determined to be 8.37 x 10(-3) and 13.87 x 10(-3) mmol g(-1) for KLT and KLT(MPDET) at 298 K, respectively. The energetic effects (Delta(int)H, Delta(int)G, and Delta(int)S) caused by metal cations adsorption were determined through calorimetric titrations. Copyright 2010. Published by Elsevier B.V.

Relationship between crystal structure and thermo-mechanical properties of kaolinite clay: Beyond standard density functional theory

DOE PAGES

Weck, Philippe F.; Kim, Eunja; Jove-Colon, Carlos F.

2015-03-04

In this study, the structural, mechanical and thermodynamic properties of 1 : 1 layered dioctahedral kaolinite clay, with ideal Al 2Si 2O 5(OH) 4 stoichiometry, were investigated using density functional theory corrected for dispersion interactions (DFT-D2). The bulk moduli of 56.2 and 56.0 GPa predicted at 298 K using the Vinet and Birch–Murnaghan equations of state, respectively, are in good agreement with the recent experimental value of 59.7 GPa reported for well-crystallized samples. The isobaric heat capacity computed for uniaxial deformation of kaolinite along the stacking direction reproduces calorimetric data within 0.7–3.0% from room temperature up to its thermal stabilitymore » limit.« less

Retention Mechanisms of Citric Acid in Ternary Kaolinite-Fe(III)-Citrate Acid Systems Using Fe K-edge EXAFS and L3,2-edge XANES Spectroscopy

PubMed Central

Yang, Jianjun; Wang, Jian; Pan, Weinan; Regier, Tom; Hu, Yongfeng; Rumpel, Cornelia; Bolan, Nanthi; Sparks, Donald

2016-01-01

Organic carbon (OC) stability in tropical soils is strongly interlinked with multivalent cation interaction and mineral association. Low molecular weight organic acids (LMWOAs) represent the readily biodegradable OC. Therefore, investigating retention mechanisms of LMWOAs in mineral-cation-LMWOAs systems is critical to understanding soil C cycling. Given the general acidic conditions and dominance of kaolinite in tropical soils, we investigated the retention mechanisms of citric acid (CA) in kaolinite-Fe(III)-CA systems with various Fe/CA molar ratios at pH ~3.5 using Fe K-edge EXAFS and L3,2-edge XANES techniques. With Fe/CA molar ratios >2, the formed ferrihydrite mainly contributed to CA retention through adsorption and/or coprecipitation. With Fe/CA molar ratios from 2 to 0.5, ternary complexation of CA to kaolinite via a five-coordinated Fe(III) bridge retained higher CA than ferrihydrite-induced adsorption and/or coprecipitation. With Fe/CA molar ratios ≤0.5, kaolinite-Fe(III)-citrate complexation preferentially occurred, but less CA was retained than via outer-sphere kaolinite-CA complexation. This study highlighted the significant impact of varied Fe/CA molar ratios on CA retention mechanisms in kaolinite-Fe(III)-CA systems under acidic conditions, and clearly showed the important contribution of Fe-bridged ternary complexation on CA retention. These findings will enhance our understanding of the dynamics of CA and other LMWOAs in tropical soils. PMID:27212680

Retention mechanisms of citric acid in ternary kaolinite-Fe(III)-citrate acid systems using Fe K-edge EXAFS and L 3,2-edge XANES spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Jianjun; Wang, Jian; Pan, Weinan

Organic carbon (OC) stability in tropical soils is strongly interlinked with multivalent cation interaction and mineral association. Low molecular weight organic acids (LMWOAs) represent the readily biodegradable OC. Therefore, investigating retention mechanisms of LMWOAs in mineral-cation-LMWOAs systems is critical to understanding soil C cycling. Given the general acidic conditions and dominance of kaolinite in tropical soils, we investigated the retention mechanisms of citric acid (CA) in kaolinite-Fe(III)-CA systems with various Fe/CA molar ratios at pH ~3.5 using Fe K-edge EXAFS and L- 3,2-edge XANES techniques. With Fe/CA molar ratios >2, the formed ferrihydrite mainly contributed to CA retention through adsorptionmore » and/or coprecipitation. With Fe/CA molar ratios from 2 to 0.5, ternary complexation of CA to kaolinite via a five-coordinated Fe(III) bridge retained higher CA than ferrihydrite-induced adsorption and/or coprecipitation. With Fe/CA molar ratios ≤ 0.5, kaolinite-Fe(III)-citrate complexation preferentially occurred, but less CA was retained than via outer-sphere kaolinite-CA complexation. This study highlighted the significant impact of varied Fe/CA molar ratios on CA retention mechanisms in kaolinite-Fe(III)-CA systems under acidic conditions, and clearly showed the important contribution of Fe-bridged ternary complexation on CA retention. In conclusion, these findings will enhance our understanding of the dynamics of CA and other LMWOAs in tropical soils.« less

Retention mechanisms of citric acid in ternary kaolinite-Fe(III)-citrate acid systems using Fe K-edge EXAFS and L 3,2-edge XANES spectroscopy

DOE PAGES

Yang, Jianjun; Wang, Jian; Pan, Weinan; ...

2016-05-23

Organic carbon (OC) stability in tropical soils is strongly interlinked with multivalent cation interaction and mineral association. Low molecular weight organic acids (LMWOAs) represent the readily biodegradable OC. Therefore, investigating retention mechanisms of LMWOAs in mineral-cation-LMWOAs systems is critical to understanding soil C cycling. Given the general acidic conditions and dominance of kaolinite in tropical soils, we investigated the retention mechanisms of citric acid (CA) in kaolinite-Fe(III)-CA systems with various Fe/CA molar ratios at pH ~3.5 using Fe K-edge EXAFS and L- 3,2-edge XANES techniques. With Fe/CA molar ratios >2, the formed ferrihydrite mainly contributed to CA retention through adsorptionmore » and/or coprecipitation. With Fe/CA molar ratios from 2 to 0.5, ternary complexation of CA to kaolinite via a five-coordinated Fe(III) bridge retained higher CA than ferrihydrite-induced adsorption and/or coprecipitation. With Fe/CA molar ratios ≤ 0.5, kaolinite-Fe(III)-citrate complexation preferentially occurred, but less CA was retained than via outer-sphere kaolinite-CA complexation. This study highlighted the significant impact of varied Fe/CA molar ratios on CA retention mechanisms in kaolinite-Fe(III)-CA systems under acidic conditions, and clearly showed the important contribution of Fe-bridged ternary complexation on CA retention. In conclusion, these findings will enhance our understanding of the dynamics of CA and other LMWOAs in tropical soils.« less

Differential capacity of kaolinite and birnessite to protect surface associated proteins against thermal degradation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chacon, Stephany S.; Garcia-Jaramillo, Manuel; Liu, Suet Yi

2018-02-28

We report it is widely accepted that soil organic carbon cycling depends on the presence and catalytic functionality of extracellular enzymes. Recent reports suggest that combusted and autoclaved soils may have the capacity to degrade organic test substrates to a larger extent than the living, enzyme-bearing soils. In search of the underlying mechanisms, we adsorbed Beta-Glucosidase (BG) and Bovine Serum Albumin (BSA) on the phyllosilicate kaolinite and the manganese oxide birnessite at pH 5 and pH 7. The protein-mineral samples were then subjected to gradual energy inputs of a magnitude equivalent to naturally occurring wildfire events. The abundance and molecularmore » masses of desorbed organic compounds were recorded after ionization with tunable synchrotron vacuum ultraviolet radiation (VUV). The mechanisms controlling the fate of proteins varied with mineralogy. Kaolinite adsorbed protein largely through hydrophobic interactions and, even at large energy inputs, produced negligible amounts of desorption fragments compared to birnessite. Acid birnessite adsorbed protein through coulombic forces at low energy levels, became a hydrolyzing catalyst at low energies and low pH, and eventually turned into a reactant involving disintegration of both mineral and protein at higher energy inputs. Fragmentation of proteins was energy dependent and did not occur below an energy threshold of 0.20 MW cm -2 . Neither signal abundance nor signal intensity were a function of protein size. Above the energy threshold value, BG that had been adsorbed to birnessite at pH 7 showed an increase in signal abundance with increasing energy applications. Signal intensities differed with adsorption pH for BSA but only at the highest energy level applied. Our results indicate that proteins adsorbed to kaolinite may remain intact after exposure to such energy inputs as can be expected to occur in natural ecosystems. Protein fragmentation and concomitant loss of functionality must be

Microscopic Mechanism and Kinetics of Ice Formation at Complex Interfaces: Zooming in on Kaolinite

PubMed Central

2016-01-01

Most ice in nature forms because of impurities which boost the exceedingly low nucleation rate of pure supercooled water. However, the microscopic details of ice nucleation on these substances remain largely unknown. Here, we have unraveled the molecular mechanism and the kinetics of ice formation on kaolinite, a clay mineral playing a key role in climate science. We find that the formation of ice at strong supercooling in the presence of this clay is about 20 orders of magnitude faster than homogeneous freezing. The critical nucleus is substantially smaller than that found for homogeneous nucleation and, in contrast to the predictions of classical nucleation theory (CNT), it has a strong two-dimensional character. Nonetheless, we show that CNT describes correctly the formation of ice at this complex interface. Kaolinite also promotes the exclusive nucleation of hexagonal ice, as opposed to homogeneous freezing where a mixture of cubic and hexagonal polytypes is observed. PMID:27269363

Behaviour of the surface hydroxide groups of exfoliated kaolinite in the gas phase and during water adsorption.

PubMed

Táborosi, Attila; Szilágyi, Róbert K

2016-02-14

The chemical and physical properties, and thus the reactivity of phylloaluminosilicates can be tailored by intercalation, delamination, and exfoliation processes. In going from the periodic crystalline to the molecular exfoliated phase, surface defects and modifications gain importance as each face of the phylloaluminosilicate comes in direct contact with the external chemical environment. In this work, we extend our earlier studies on the molecular cluster modelling of exfoliated kaolinite sheets by evaluating the positions and orientations of surface hydroxide groups and bridging oxide anions, as the sites of reactivity. The previous focus on the inner chemical environment of a single kaolinite layer is shifted to the surface exposed octahedral aluminium-hydroxide and tetrahedral silicon-oxide sheets. The combination of semi-empirical, ab initio wave function, and density functional calculations unanimously support the amphoteric nature of the surface hydroxide groups with respect to H-bonding donor/acceptor capabilities. To a lesser extent, we observe the same for the bridging oxide anions. This is in contrast to the crystalline phase, which manifests only donor orientation for maintaining an inter-layer H-bond network. These results suggest that both electrophilic and nucleophilic characteristics of the octahedral and tetrahedral sheets need to be considered during intercalation and concomitant exfoliation of the kaolinite sheets.

Fractionation of aquatic natural organic matter upon sorption to goethite and kaolinite

USGS Publications Warehouse

Meier, M.; Namjesnik-Dejanovic, K.; Maurice, P.A.; Chin, Y.-P.; Aiken, G.R.

1999-01-01

Natural organic matter (NOM) consists of a complex mixture of organic molecules; previous studies have suggested that preferential sorption of higher molecular weight, more hydrophobic, and more aromatic components may lead to fractionation of the NOM pool upon passage through porous media. Our work expands upon previous studies by quantifying the change in solution-phase weight average molecular weight (M(w)) upon sorption of bulk (rather than isolated) surface water NOM from the Suwannee River (SR) and the Great Dismal Swamp (GDS) to goethite and kaolinite at different sorption densities and at pH 4, 22??C. High pressure size exclusion chromatography (HPSEC) was used to quantify changes in M(w) upon sorption, and molar absorptivities at ?? = 280 nm were used to approximate changes in solution NOM aromaticity. Two SR water samples were used, with M(w) = 2320 and 2200 Da; a single GDS sample was used, with M(w) = 1890 Da. The SR NOM was slightly more hydrophobic and aromatic. These differences were reflected in greater sorption of SR NOM than GDS NOM. Both surface water NOMs showed a much greater affinity for goethite than for kaolinite. HPSEC analysis of the NOM remaining in solution after 24 h reaction time with geothite revealed that the largest changes in solution phase M(w)s (decreases by 900-1700 Da) occurred at relatively low equilibrium sorbate concentrations (approximately 5-20 mg C 1-1); the decrease in solution M(w) suggested that reactive surface sites were occupied disproportionately by large and intermediate size NOM moieties. At higher equilibrium NOM concentrations (>20 mg C 1-1), as percent adsorption decreased, M(w) in solution was similar to original samples. A smaller decrease in solution NOM M(w) (300-500 Da at 10-20 mg C 1-1 ~ 100 Da at > 20 mg) also occurred upon sorption to kaolinite. Overall, our results showed that factors (as related to NOM composition, clay mineral surface properties, and position along the sorption isotherm) which

Effect of polyvinylpyrrolidone and sodium lauroyl isethionate on kaolinite suspension in an aqueous phase.

PubMed

Kwan, Chang-Chin; Chu, Wen-Hweu; Shimabayashi, Saburo

2006-08-01

Suspension of concentrated kaolinite (20 g/30 ml-medium) in the presence of polyvinylpyrrolidone (PVP) and sodium lauroyl isethionate (SLI) was allowed to evaluate its degree of dispersion based on their rheological studies. Flow curves at low shear rate, measured by means of cone-plate method, showed a non-Newtonian flow. Plastic viscosity and Bingham yield value were derived from the flow curves. Relative viscosity, effective volume fraction and void fraction of secondary particle were also obtained. Results of dispersity and fluidity of the suspension were explained. PVP acted as a flocculant at a concentration lower than 0.1% but as a dispersant at a higher concentration. The presence of SLI could decrease both the Bingham yield value and suspension viscosity. Cooperative and competitive effects of PVP and SLI were found. Results indicated that SLI enhanced the degree of dispersion of kaolinite when PVP was less than 0.1%. The suspension, however, showed a maximum flocculation (i.e., aggregation) at 4 mM SLI when the concentration of PVP was higher than 0.1%.

Application of Brazilian kaolinite clay as adsorbent to removal of U(VI) from aqueous solution: Kinetic and thermodynamic of cation-basic interactions

NASA Astrophysics Data System (ADS)

Guerra, Denis L.; Leidens, Victor L.; Viana, Rúbia R.; Airoldi, Claudio

2010-05-01

The compound N 1-[3-(trimethoxysilyl)propyl]diethylenetriamine was anchored onto Amazon kaolinite surface by heterogeneous route. The modified and natural kaolinite samples were characterized by transmission electron microscopy, scanning electron microscopic, X-ray diffraction, and nuclear magnetic nuclei of 29Si and 13C. The well-defined peaks obtained in the 13C NMR spectrum in the 5.0-62.1 ppm region confirmed the attachment of organic functional groups as pendant chains bonded into the porous clay. The ability of these materials to remove U(VI) from aqueous solution was followed by a series of adsorption isotherms adjusted to a Sips equation at room temperature and pH 4.0. The kinetic parameters analyzed by the Lagergren and Elovich models gave a good fit for a pseudo-second order reaction with k2 values 16.0 and 25.1 mmol g -1 min -1 ranges for natural and modified kaolinite clays, respectively. The energetic effects caused by metal ion adsorption were determined through calorimetric titrations.

Adhesion of the clay minerals montmorillonite, kaolinite, and attapulgite reduces respiration of Histoplasma capsulatum.

PubMed Central

Lavie, S; Stotzky, G

1986-01-01

The respiration of three phenotypes of Histoplasma capsulatum, the causal agent of histoplasmosis in humans, was markedly reduced by low concentrations of montmorillonite but was reduced less by even higher concentrations of kaolinite or attapulgite (palygorskite). The reduction in respiration followed a pattern that suggested saturation-type kinetics: an initial sharp reduction that occurred with low concentrations of clay (0.01 to 0.5% [wt/vol]), followed by a more gradual reduction with higher concentrations (1 to 8%). Increases in viscosity (which could impair the movement of O2) caused by the clays were not responsible for the reduction in respiration, and the clays did not interfere with the availability of nutrients. Scanning electron microscopy after extensive washing showed that the clay particles were tightly bound to the hyphae, suggesting that the clays reduced the rate of respiration of H. capsulatum by adhering to the mycelial surface and, thereby, interfered with the movement of nutrients, metabolites, and gases across the mycelial wall. Images PMID:3954340

Adhesion of the clay minerals montmorillonite, kaolinite, and attapulgite reduces respiration of Histoplasma capsulatum.

PubMed

Lavie, S; Stotzky, G

1986-01-01

The respiration of three phenotypes of Histoplasma capsulatum, the causal agent of histoplasmosis in humans, was markedly reduced by low concentrations of montmorillonite but was reduced less by even higher concentrations of kaolinite or attapulgite (palygorskite). The reduction in respiration followed a pattern that suggested saturation-type kinetics: an initial sharp reduction that occurred with low concentrations of clay (0.01 to 0.5% [wt/vol]), followed by a more gradual reduction with higher concentrations (1 to 8%). Increases in viscosity (which could impair the movement of O2) caused by the clays were not responsible for the reduction in respiration, and the clays did not interfere with the availability of nutrients. Scanning electron microscopy after extensive washing showed that the clay particles were tightly bound to the hyphae, suggesting that the clays reduced the rate of respiration of H. capsulatum by adhering to the mycelial surface and, thereby, interfered with the movement of nutrients, metabolites, and gases across the mycelial wall.

Probing the Surface Charge on the Basal Planes of Kaolinite Particles with High-Resolution Atomic Force Microscopy

PubMed Central

2017-01-01

High-resolution atomic force microscopy is used to map the surface charge on the basal planes of kaolinite nanoparticles in an ambient solution of variable pH and NaCl or CaCl2 concentration. Using DLVO theory with charge regulation, we determine from the measured force–distance curves the surface charge distribution on both the silica-like and the gibbsite-like basal plane of the kaolinite particles. We observe that both basal planes do carry charge that varies with pH and salt concentration. The silica facet was found to be negatively charged at pH 4 and above, whereas the gibbsite facet is positively charged at pH below 7 and negatively charged at pH above 7. Investigations in CaCl2 at pH 6 show that the surface charge on the gibbsite facet increases for concentration up to 10 mM CaCl2 and starts to decrease upon further increasing the salt concentration to 50 mM. The increase of surface charge at low concentration is explained by Ca2+ ion adsorption, while Cl– adsorption at higher CaCl2 concentrations partially neutralizes the surface charge. Atomic resolution imaging and density functional theory calculations corroborate these observations. They show that hydrated Ca2+ ions can spontaneously adsorb on the gibbsite facet of the kaolinite particle and form ordered surface structures, while at higher concentrations Cl– ions will co-adsorb, thereby changing the observed ordered surface structure. PMID:29140711

Probing the Surface Charge on the Basal Planes of Kaolinite Particles with High-Resolution Atomic Force Microscopy.

PubMed

Kumar, N; Andersson, M P; van den Ende, D; Mugele, F; Siretanu, I

2017-12-19

High-resolution atomic force microscopy is used to map the surface charge on the basal planes of kaolinite nanoparticles in an ambient solution of variable pH and NaCl or CaCl 2 concentration. Using DLVO theory with charge regulation, we determine from the measured force-distance curves the surface charge distribution on both the silica-like and the gibbsite-like basal plane of the kaolinite particles. We observe that both basal planes do carry charge that varies with pH and salt concentration. The silica facet was found to be negatively charged at pH 4 and above, whereas the gibbsite facet is positively charged at pH below 7 and negatively charged at pH above 7. Investigations in CaCl 2 at pH 6 show that the surface charge on the gibbsite facet increases for concentration up to 10 mM CaCl 2 and starts to decrease upon further increasing the salt concentration to 50 mM. The increase of surface charge at low concentration is explained by Ca 2+ ion adsorption, while Cl - adsorption at higher CaCl 2 concentrations partially neutralizes the surface charge. Atomic resolution imaging and density functional theory calculations corroborate these observations. They show that hydrated Ca 2+ ions can spontaneously adsorb on the gibbsite facet of the kaolinite particle and form ordered surface structures, while at higher concentrations Cl - ions will co-adsorb, thereby changing the observed ordered surface structure.

EFFECTS OF PH, SOLID/SOLUTION RATIO, IONIC STRENGTH, AND ORGANIC ACIDS ON PB AND CD SOPRTION ON KAOLINITE

EPA Science Inventory

Potentiometric and ion-selective electrode titrations together with batch sorption/desorption experiments, were performed to explain the aqueous and surface complexation reactions between kaolinite, Pb, Cd and three organic acids. Variables included pH, ionic strength, metal conc...

Polyacrylic acid grafted kaolinite via a facile ‘grafting to’ approach based on heterogeneous esterification and its adsorption for Cu2+

NASA Astrophysics Data System (ADS)

Zhao, Ping; Zhou, Qi; Yan, Chunjie; Luo, Wenjun

2017-03-01

Kaolinite (KLN) was successfully decorated by polyacrylic acid (PAA) brushes via a facile ‘one-step’ manner in this study. This process was achieved by heterogeneous esterification between carboxyl on the PAA chains and hydroxyl on the KLN in the presence of Al3+ as catalyst. The prepared composite (denoted as PAA-g-KLN) was characterized by Fourier transform infrared spectroscopy (FTIR), x-ray diffraction pattern (XRD), Field emission scanning electron microscopy (FE-SEM) and thermogravimetry (TG) to confirm the successful grafting of PAA brushes on the surface of KLN. Subsequently, the PAA-g-KLN was used as adsorbent for the removal of Cu2+ from wastewater. Due to the introduction of abundant and highly accessible carboxyl groups on the surface of kaolinite, PAA-g-KLN exhibited an enhanced adsorption performance than raw kaolinite, which could be up to 32.45 mg·g-1 at 45 °C with a fast adsorption kinetic. Theoretical models analysis revealed that Langmuir isotherm model and the pseudo second-order model were more suitable for well elucidation of the experimental data. In addition, the regeneration experiment showed that the PAA-g-KLN could still keep a satisfactory adsorption capacity (>65%) by being reused for 6 consecutive cycles. The study provides an easy and rapid method for surface polyelectrolyte modification on inorganic mineral as a promising adsorbent to remove Cu2+ from aqueous solution.

Adsorption and fractionation of a muck fulvic acid on kaolinite and goethite at pH 3.7,6, and 8

USGS Publications Warehouse

Namjesnik-Dejanovic, K.; Maurice, P.A.; Aiken, G.R.; Cabaniss, S.; Chin, Y.-P.; Pullin, M.J.

2000-01-01

Molecular weight (MW) of humic materials is a key factor controlling proton and metal binding and organic pollutant partitioning. Several studies have suggested preferential adsorption of higher MW, more aromatic moieties to mineral surfaces; quantification of such processes is fundamental to development of predictive models. We used high pressure size exclusion chromatography (HPSEC) to quantify MW changes upon adsorption of a muck fulvic acid (MFA) extracted from a peat deposit to kaolinite and goethite, at pH 3.7,6, and 8 at 22 ??C, I = 0.01 (NaC1), 24-h reaction time. MFA adsorption affinity was greater for goethite than for kaolinite. At concentrations less than the adsorption maximum (A(max)) for both adsorbents, the weight-average MW (M(w)) of MFA remaining in solution decreased by as much as several hundred Daltons relative to control samples, indicating preferential adsorption of the higher MW components. At concentrations more than A(max), M(w) of MFA in solution did not change appreciably. Although total adsorption decreased significantly as pH increased, fractionation as measured by change in M(w) remained similar, perhaps indicating greater selectivity for higher MW components at higher pH. Absorptivities at ?? = 280 nm normalized to mg C L-1 (??) suggested preferential adsorption of more aromatic moieties to kaolinite. ?? could not be used for goethite-reacted samples because high Fe concentrations in the aqueous phase brought about by goethite dissolution interfered with the spectroscopic analysis. Preliminary kinetic experiments suggested that smaller molecules adsorbed first and were replaced by larger molecules whose adsorption was thermodynamically favored.

Interactions of low molecular weight aromatic acids and amino acids with goethite, kaolinite and bentonite with or without organic matter coating

NASA Astrophysics Data System (ADS)

Gao, Jiajia; Jansen, Boris; Cerli, Chiara; Kalbitz, Karsten

2015-04-01

Interaction of organic matter molecules with the soil's solid phase is a key factor influencing the stabilization of carbon in soils and thus forms a crucial aspect of the global carbon cycle. While subject of much research attention so far, we still have much to learn about such interactions at the molecular level; in particular in the light of competition between different classes of organic molecules and in the presence of previously adsorbed soil organic matter. We studied the interaction of a group of low molecular weight (LMW) aromatic acids (salicylic, syringic, vanillic and ferulic acid) and amino acids (lysine, glutamic, leucine and phenylalanine) on goethite, kaolinite and bentonite with and without previously adsorbed dissolved organic matter (DOM). For this we used batch experiments at pH = 6.0 where some of the organic compounds were positively charged (i.e. lysine) or negatively charged (i.e. glutamic and salicylic acid) while the minerals also displayed positively (i.e. goethite) or negatively charged surfaces (i.e. bentonite). We found much higher sorption of salicylic acid and lysine than other compounds. On the bare minerals we found a great variety of sorption strength, with salicylic acid strongly adsorbed, while syringic, vanillic and ferulic acid showed little or no adsorption. For the amino acids, protonated lysine showed a stronger affinity to negatively charged kaolinite and bentonite than other amino acids. While deprotonated glutamic acid showed the strongest adsorption on goethite. Leucine and phenylalanine showed hardly any adsorption on any of the minerals. When present concurrently, amino acids decreased the sorption of salicylic acid on the three types of mineral, while the presence of LMW aromatic acids increased the sorption of lysine on kaolinite and bentonite and the sorption of glutamic acid on goethite. The presence of previously adsorbed DOM reduced the sorption of salicylic acid and lysine. The results confirm that

Effect of Cosolutes on the Sorption of Phenanthrene onto Mineral Surface of River Sediments and Kaolinite

PubMed Central

2014-01-01

Sorption of phenanthrene onto the natural sediment with low organic carbon content (OC%), organic-free sediment, and kaolinite was investigated through isotherm experiments. Effects of cosolutes (pyrene, 4-n-nonyphenol (NP), and humic acid (HA)) on phenanthrene sorption were also studied by comparing apparent solid-water distribution coefficients (K d app) of phenanthrene. Two addition sequences, including “cosolute added prior to phenanthrene” and “cosolute and phenanthrene added simultaneously,” were adopted. The Freundlich model fits phenanthrene sorption on all 3 sorbents well. The sorption coefficients on these sorbents were similar, suggesting that mineral surface plays an important role in the sorption of hydrophobic organic contaminants on low OC% sediments. Cosolutes could affect phenanthrene sorption on the sorbents, which depended on their properties, concentrations, and addition sequences. Pyrene inhibited phenanthrene sorption. Sorbed NP inhibited phenanthrene sorption at low levels and promoted sorption at high levels. Similar to NP, effect of HA on phenanthrene sorption onto the natural sediment depended on its concentrations, whereas, for the organic-free sediment and kaolinite, preloading of HA at high levels led to an enhancement in phenanthrene K d app while no obvious effect was observed at low HA levels; dissolved HA could inhibit phenanthrene sorption on the two sorbents. PMID:25147865

Effects of Siderophores on Metal Adsorption to Kaolinite

NASA Astrophysics Data System (ADS)

Hepinstall, S. E.; Maurice, P. A.; Miller, M. J.

2003-12-01

Siderophores are metal-complexing ligands with high affinities for Fe(III), produced by many microorganisms in Fe-deficient environments. Siderophores can also form strong complexes with other metals such as Pb and Cd; hence, siderophores may play an important role in controlling metal mobility in porous media. This study compared the effects of siderophores desferrioxamine-B (DFO-B), desferrioxamine-D (DFO-D1), desferrioxamine-E (DFO-E), as well as siderophore-like ligand acetohydroxamic acid (aHA) on Pb and Cd adsorption to kaolinite (KGa-1b) at pH 4.5 to 9, in 0.1 M NaClO4, at 22 \\deg C, in the dark. At pH > 6.5 all of the siderophores plus aHA, inhibited Pb adsorption, with inhibition increasing in the order aHA < DFO-D1 < DFO-B < DFO-E. At lower pH, all four ligands slightly enhanced Pb adsorption. These ligands also inhibited Cd adsorption at high pH, but had little or no effect at low pH. These results suggest that siderophore effects on metal mobility through porous media are likely to be complex and variable with pH.

Combination of multi-scale and multi-edge X-ray spectroscopy for investigating the products obtained from the interaction between kaolinite and metallic iron in anoxic conditions at 90 °C

NASA Astrophysics Data System (ADS)

Rivard, Camille; Montargès-Pelletier, Emmanuelle; Vantelon, Delphine; Pelletier, Manuel; Karunakaran, Chithra; Michot, Laurent J.; Villieras, Frédéric; Michau, Nicolas

2013-02-01

In the context of radioactive waste repository in geological formation, kaolinite-metallic iron interaction in chlorine solution was conducted in batch experiments, under anoxic conditions at 90 °C during 9 months. After a mineralogical characterization at a global scale, products were analyzed at the micrometer and nanometer scales by X-ray absorption spectroscopic techniques (XAS and STXM). Absorption at Al, Si and Fe edges was investigated to have a complete overview of the distribution and status of constituting elements. Whereas Si K-edge results do not evidence significant evolution of silicon status, investigations at Al K-edge and Fe L-edges demonstrate variations at aggregate and particle scales of IVAl:VIAl and Fe2+:Fe3+ ratios. Spectroscopic data evidence the systematic crystallization of Fe-serpentines onto the remaining particles of kaolinite and the absence of pure species (kaolinite or Fe-serpentines). Combination of spatially resolved spectroscopic analyses and TEM-EDXS elemental distribution aims to calculate unit cell formulae of Fe-serpentines layers and abundance of each species in mixed particles. For most of the investigated particles, results reveal that the variations of particles composition are directly linked to the relative contributions of kaolinite and Fe-berthierine in mixed particles. However, for some particles, microscale investigations evidence crystallization of two other Fe-serpentines species, devoid of aluminum, cronstedtite and greenalite.

Effect of Acid on Surface Hydroxyl Groups on Kaolinite and Montmorillonite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sihvonen, Sarah K.; Murphy, Kelly A.; Washton, Nancy M.

Mineral dust aerosol participates in heterogeneous chemistry in the atmosphere. In particular, the hydroxyl groups on the surface of aluminosilicate clay minerals are important for heterogeneous atmospheric processes. These functional groups may be altered by acidic processing during atmospheric transport. In this study, we exposed kaolinite (KGa-1b) and montmorillonite (STx-1b) to aqueous sulfuric acid and then rinsed the soluble reactants and products off in order to explore changes to functional groups on the mineral surface. To quantify the changes due to acid treatment of edge hydroxyl groups, we use 19F magic angle spinning nuclear magnetic resonance spectroscopy and a probemore » molecule, 3,3,3-trifluoropropyldimethylchlorosilane. We find that the edge hydroxyl groups (OH) increase in both number and density with acid treatment. Chemical reactions in the atmosphere may be impacted by the increase in OH at the mineral edge.« less

Aggregation Rates of Sediments (Montmorillonite, Kaolinite, Illite and Goethite) with the Enveloped Φ6 Bacteriophage

NASA Astrophysics Data System (ADS)

Katz, A.; Block, K. A.; Peña, S.; Alimova, A.; Gottlieb, P.

2015-12-01

The interaction between sediments and viruses has been studied extensively from the prospective of virus survivability and infectivity. However, the role of soil organisms, including viruses in C and N sequestration in soil has not been studied as extensively. Φ6, a member of the cystoviridae family, is a bacteriophage that infects Pseudomonas syringae, a common plant pathogen known to readily form biofilms.The small mineral fraction (< 0.2 μm) of soil and Φ6 are colloidal particles, therefore aggregation can be explained by DLVO (Derjaguin & Landau, Verwey & Overbeek) theory. Time-resolved visible-light turbidity measurements were used to calculate the heteroaggregation rates of Φ6 with the sediments. Samples were suspended in a low-concentration cation buffer so that the kinetics were in the reaction limited cluster aggregation (RLCA) regime in where the probability of two particles adhering after collision is determined by the interaction forces between the particles.At neutral pH to slightly acidic pH, Φ6 is slightly negatively charged; montmorillonite and illite are negatively charged; and kaolinite and goethite are positively charged. In isolation, neither Φ6 nor the sediments aggregated in the modified buffer. However, in mixtures, Φ6 and montmorillonite, and Φ6 and illite, exhibited increases in turbidity, indicating heteroaggregation. Neither Φ6 and kaolinite, nor Φ6 and goethite, exhibited increased turbidity upon mixing indicating little or no aggregation. These results suggest that the interaction of the virus with the sediments is governed by hydrophobic rather than electrostatic forces. Heteroaggregation rates were calculated from the time rate of change of the turbidity.

Promoting the Adsorption of Metal Ions on Kaolinite by Defect Sites: A Molecular Dynamics Study

PubMed Central

Li, Xiong; Li, Hang; Yang, Gang

2015-01-01

Defect sites exist abundantly in minerals and play a crucial role for a variety of important processes. Here molecular dynamics simulations are used to comprehensively investigate the adsorption behaviors, stabilities and mechanisms of metal ions on defective minerals, considering different ionic concentrations, defect sizes and contents. Outer-sphere adsorbed Pb2+ ions predominate for all models (regular and defective), while inner-sphere Na+ ions, which exist sporadically only at concentrated solutions for regular models, govern the adsorption for all defective models. Adsorption quantities and stabilities of metal ions on kaolinite are fundamentally promoted by defect sites, thus explaining the experimental observations. Defect sites improve the stabilities of both inner- and outer-sphere adsorption, and (quasi) inner-sphere Pb2+ ions emerge only at defect sites that reinforce the interactions. Adsorption configurations are greatly altered by defect sites but respond weakly by changing defect sizes or contents. Both adsorption quantities and stabilities are enhanced by increasing defect sizes or contents, while ionic concentrations mainly affect adsorption quantities. We also find that adsorption of metal ions and anions can be promoted by each other and proceeds in a collaborative mechanism. Results thus obtained are beneficial to comprehend related processes for all types of minerals. PMID:26403873

Air oxidation of hydrazine. 1. Reaction kinetics on natural kaolinites, halloysites, and model substituent layers with varying iron and titanium oxide and O- center contents

NASA Technical Reports Server (NTRS)

Coyne, L.; Mariner, R.; Rice, A.

1991-01-01

Air oxidation of hydrazine was studied by using a group of kaolinites, halloysites, and substituent oxides as models for the tetrahedral and octahedral sheets. The rate was found to be linear with oxygen. The stoichiometry showed that oxygen was the primary oxidant and that dinitrogen was the only important nitrogen-containing product. The rates on kaolinites were strongly inhibited by water. Those on three-dimensional silica and gibbsite appeared not to be. That on a supposedly layered silica formed from a natural kaolinite by acid leaching showed transitional behavior--slowed relative to that expected from a second-order reaction relative to that on the gibbsite and silica but faster than those on the kaolinites. The most striking result of the reaction was the marked increase in the rate of reaction of a constant amount of hydrazine as the amount of clay was increased. The increase was apparent (in spite of the water inhibition at high conversions) over a 2 order of magnitude variation of the clay weight. The weight dependence was taken to indicate that the role of the clay is very important, that the number of reactive centers is very small, or that they may be deactivated over the course of the reaction. In contrast to the strong dependence on overall amount of clay, the variation of amounts of putative oxidizing centers, such as structural Fe(III), admixed TiO2 or Fe2O3, or O- centers, did not result in alteration of the rate commensurate with the degree of variation of the entity in question. Surface iron does play some role, however, as samples that were pretreated with a reducing agent were less active as catalysts than the parent material. These results were taken to indicate either that the various centers interact to such a degree that they cannot be considered independently or that the reaction might proceed by way of surface complexation, rather than single electron transfers.

Study of chemical and thermal treatment of kaolinite and its influence on the removal of contaminants from mining effluents.

PubMed

de Sales, Priscila F; Magriotis, Zuy M; Rossi, Marco Aurélio de L S; Tartuci, Letícia G; Papini, Rísia M; Viana, Paulo R M

2013-10-15

The effects of chemical and thermal treatments on the structure of kaolinite were examined, as well as the influence of those changes upon the removal of etheramine, a cationic collector used in the processing of iron ore. The materials were characterized using XRD, XRF, specific surface area (SBET), FTIR, zeta potential and a test for determination of acid sites. The effects of the treatments on the structure of kaolinite were evaluated using chemometric tools developed from principal components analysis algorithms and hierarchical components analysis. The parameters evaluated in the kinetic study of adsorption were contact time, initial concentration of etheramine, quantity of adsorbent and pH. The adsorption of etheramine in the samples subjected to chemical treatments could be explained by a pseudo-second order model, whilst for the sample subjected to thermal treatment, better fit was with the pseudo-first order model. With regard to adsorption isotherms, it was shown that for the three adsorbents used, adsorption followed the Langmuir model. The maximum quantities adsorbed were 27 mg g(-1), 29 mg g(-1) and 59 mg g(-1), respectively, for the samples subjected to acid, thermal and peroxide treatments. The treatment with peroxide was found to be the most suitable for removal of etheramine. Copyright © 2013 Elsevier Ltd. All rights reserved.

Adsorption and structure of water on kaolinite surfaces: possible insight into ice nucleation from grand canonical monte carlo calculations.

PubMed

Croteau, T; Bertram, A K; Patey, G N

2008-10-30

Grand canonical Monte Carlo calculations are used to determine water adsorption and structure on defect-free kaolinite surfaces as a function of relative humidity at 235 K. This information is then used to gain insight into ice nucleation on kaolinite surfaces. Results for both the SPC/E and TIP5P-E water models are compared and demonstrate that the Al-surface [(001) plane] and both protonated and unprotonated edges [(100) plane] strongly adsorb at atmospherically relevant relative humidities. Adsorption on the Al-surface exhibits properties of a first-order process with evidence of collective behavior, whereas adsorption on the edges is essentially continuous and appears dominated by strong water lattice interactions. For the protonated and unprotonated edges no structure that matches hexagonal ice is observed. For the Al-surface some of the water molecules formed hexagonal rings. However, the a o lattice parameter for these rings is significantly different from the corresponding constant for hexagonal ice ( Ih). A misfit strain of 14.0% is calculated between the hexagonal pattern of water adsorbed on the Al-surface and the basal plane of ice Ih. Hence, the ring structures that form on the Al-surface are not expected to be good building-blocks for ice nucleation due to the large misfit strain.

Adsorption properties of kaolinite-based nanocomposites for Fe and Mn pollutants from aqueous solutions and raw ground water: kinetics and equilibrium studies.

PubMed

Shaban, Mohamed; Hassouna, Mohamed E M; Nasief, Fadya M; AbuKhadra, Mostafa R

2017-10-01

Raw kaolinite was used in the synthesis of metakaolinite/carbon nanotubes (K/CNTs) and kaolinite/starch (K/starch) nanocomposites. Raw kaolinite and the synthetic composites were characterized using XRD, SEM, and TEM techniques. The synthetic composites were used as adsorbents for Fe and Mn ions from aqueous solutions and natural underground water. The adsorption by the both composites is highly pH dependent and achieves high efficiency within the neutral pH range. The experimental adsorption data for the uptake of Fe and Mn ions by K/CNTs were found to be well represented by the pseudo-second-order kinetic model rather than the intra-particle diffusion model or Elovich model. For the adsorption using K/starch, the uptake results of Fe ions was well fitted by the second-order model, whereas the uptake of Mn ions fitted well to the Elovich model rather than pseudo-second-order and intra-particle diffusion models The equilibrium studies revealed the excellent fitting of the removal of Fe and Mn ions by K/CNTs and Fe using K/starch with the Langmuir isotherm model rather than with Freundlich and Temkin models. But the adsorption of Mn ions by K/starch is well fitted with Freundlich rather than Temkin and Langmuir isotherm models. The thermodynamic studies reflected the endothermic nature and the exothermic nature for the adsorption by K/CNTs and K/starch nanocomposites, respectively. Natural ground water contaminated by 0.4 mg/L Fe and 0.5 mg/L Mn was treated at the optimum conditions of pH 6 and 120 min contact time. Under these conditions, 92.5 and 72.5% Fe removal efficiencies were achieved using 20 mg of K/CNTs and K/starch nanocomposites, respectively. Also, K/CNTs nanocomposite shows higher efficiency in the removal of Mn ions as compared to K/starch nanocomposite.

Kaolinite-catalyzed air oxidation of hydrazine: Consideration of several compositional, structural and energetic factors in surface activation

NASA Technical Reports Server (NTRS)

Coyne, L. M.; Mariner, R.; Rice, A.

1991-01-01

Clay minerals have been shown to have numerous, curious, energetic properties by virtue of ultra-violet light release which can be triggered by gentle environmental changes such as wetting and dewetting by a variety of liquids, unique among them water and hydrazine. Since both water and hydrazine play multiple key roles in the air-oxidation of hydrazine on kaolinite surfaces, this reaction would seem to have prime potential for studying interrelationships of energy storage, release and chemical reactivity of clay surfaces, capacities basic to either the Bernal or Cairns-Smith roles of minerals in the origin of life. Establishment of the capacity for stored electronic energy to significantly alter surface chemistry is important, regardless of the reaction chosen to demonstrate it. Hydrazine air oxidation is overawingly complex, given the possibilities for step-wise control and monitoring of parameters. In the light of recently extended characterization of the kaolinite and model sheet catalysts we used to study hydrazine oxidation and gamma-irradiated silica, previous studies of hydrazine air-oxidation on aluminosilicate surfaces have been reevaluated. Our former conclusion remains intact that, whereas trace structural and surface contaminants do play some role in the catalysis of oxidation, they are not the only, nor even the dominant, catalytic centers. Initial intermediates in the oxidation can now be proposed which are consistent with production via O(-)-centers as well as ferric iron centers. The greater than square dependence of the initial reaction rate on the weight of the clay is discussed in the light of these various mechanistic possibilities.

An example of applied structural petrology in the Illinois Basin: Sphalerite kaolinite and their relation to the depth and relative timing of coal jointing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ambers, C.P.

1993-03-01

Sphalerite is associated with very well crystallized kaolinite (VWCK) in geodes, siderite nodules and coal cleats in the Illinois Basin and allows estimation of the temperature of formation of the VWCK using fluid inclusions. The approximate depth of kaolinite growth and the relative timing of coal fracturing can then be ascertained. Sphalerite associated with VWCK was extracted from Mississippian geodes collected near Keokuk, Iowa, and from Pennsylvanian siderite nodules and coal collected in SW Indiana. Inclusions in the sphalerite consist of VWCK; large, negative crystal, two-phase fluid inclusions; small, fracture-related, two-phase fluid inclusions; and organic inclusions. Homogenization temperatures of 89more » C [+-] 10, 115 C [+-] 15, 89 C [+-] 5 were measured for the two-phase inclusions in sphalerite from the geodes, siderite nodules and coal, respectively. Freezing temperatures of the inclusions in the geode and siderite nodule sphalerite were measured at [minus]13.5 C [+-] 0.5 and [minus]9.4 C [+-] 0.2, indicating moderate salinity. Using a geothermal gradient range of 23--36 C/km and an average surface temperature of 20 C, kaolinite and sphalerite probably grew at depths of about 1.9 to 4.1 km. In SW Indiana, VWCK occurs in vertical, non-penetrative joints in vitrinite layers. Penetrative joint sets rarely contain VWCK. At nearly all of the 28 sites studied, two sets of barren cleats occur oriented N10W to NSE and N80E to N95E. The orientation of barren, penetrative cleats shows that the maximum horizontal stress rotated CW from the earlier stress field. Rare VWCK in the late cleats suggests they also formed at depth after the thermal maxima.« less

Formation and Release of Cobalt(II) Sorption and Precipitation Products in Aging Kaolinite-Water Slurries.

PubMed

Thompson; Parks; Brown

2000-02-15

The uptake and release behavior of cobalt(II) was studied over thousands of hours in CO(2)-free aqueous suspensions of kaolinite under three pairs of total cobalt concentration (Co(T)) and near-neutral pH (7.5-7.8) conditions. Dissolved cobalt, aluminum, and silicon concentrations were monitored by ICPMS, and cobalt-containing products were identified by EXAFS spectroscopy. In each uptake experiment, cobalt sorbed to kaolinite as a mixture of surface-adsorbed monomers or polymers and hydrotalcite-like precipitates of the approximate composition Co(x)Al(OH)(2x+2)(A(n-))(1/n), where 2

Unraveling climatic changes from intra-profile variation in oxygen and hydrogen isotopic composition of goethite and kaolinite in laterites: An integrated study from Yaou, French Guiana

NASA Astrophysics Data System (ADS)

Girard, Jean-Pierre; Freyssinet, Philippe; Chazot, Gilles

2000-02-01

An integrated study of O and H isotopes in the lateritic profile of Yaou, French Guiana, was undertaken to investigate the usefulness of stable isotopes as tracers of climatic changes in continental environments. The studied profile is composed of a 27 m thick saprolite, mostly developed in the past under wet-and-dry tropical climate in association with a duricrust, overlain by a 3 m thick yellow latosol formed more recently under present equatorial hot and humid climate. δ 18O-δD values determined for weathering goethite (pseudomorphs after pyrite) and kaolinite (microcrystalline clay groundmass) throughout the 30 m deep profile reflect formation temperatures consistent with present (25°C) and realistic past climatic temperatures (20°C-30°C), indicating that weathering minerals formed in isotopic equilibrium with their genetic environment and were not subjected to significant isotope exchange after formation. A distinct shift downward (2‰ for δ 18O, 15‰ for δD) from low to high δ 18O-δD values occurs around 20 m depth in the saprolite. It is interpreted as recording the change from the past tropical to the present equatorial climate. Goethite and kaolinite in the 5-10 m thick saprolite interval immediately above the active basement weathering front are in isotopic equilibrium with modern water and must have formed under present equatorial-humid conditions. In contrast, goethite and kaolinite found higher up in the saprolite and in the duricrust formed in the past under tropical wet and dry climate from waters distinctly depleted in 18O and D relative to modern water. The marked depletion of paleo-meteoric water at Yaou most likely reflects a more contrasted or "monsoonal" character of the ancient tropical climate. The present study shows that ancient weathering minerals in lateritic profiles preserve their δ 18O-δD values and carry a time signal. The time signal is best expressed in minerals formed rapidly at the weathering front and not subjected

Synthesis of hectorite-TiO2 and kaolinite-TiO2 nanocomposites with photocatalytic activity for the degradation of model air pollutants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Destaillats, Hugo; Kibanova, D.; Trejo, M.

2008-03-01

We studied the synthesis and photocatalytic activity of small-sized TiO{sub 2} supported on hectorite and kaolinite. Deposition of TiO{sub 2} on the clay mineral surface was conducted by using a sol-gel method with titanium isopropoxide as precursor. Anatase TiO{sub 2} particles formation was achieved by hydrothermal treatment at 180 C. Material characterization was conducted using XRD, SEM, XPS, ICP-OES, BET and porosimetry analysis. Efficiency in synthesizing clay-TiO{sub 2} composites depended strongly on the clay mineral structure. Incorporation of anatase in hectorite, an expandable clay mineral, was found to be very significant (> 36 wt.% Ti) and to be followed bymore » important structural changes at the clay mineral surface. Instead, no major structural modifications of the clay were observed for kaolinite-TiO{sub 2}, as compared with the untreated material. Photocatalytic performance of clay-TiO{sub 2} composites was evaluated with ATR-FTIR following the oxidation of adsorbed toluene and d-limonene, two model air pollutants. In either case, the photocatalytic removal efficiency of these hydrophobic substrates by the synthesized clay-TiO{sub 2} composites was comparable to that observed using pure commercial TiO{sub 2} (Degussa P25).« less

Effect of the acid treatment conditions of kaolinite on etheramine adsorption: A comparative analysis using chemometric tools.

PubMed

Leal, Paulo Vitor Brandão; Magriotis, Zuy Maria; Sales, Priscila Ferreira de; Papini, Rísia Magriotis; Viana, Paulo Roberto de Magalhães

2017-07-15

The present work evaluated the effect of the acid treatment conditions of natural kaolinite (NK) regarding its efficiency in removing etheramine. The treatment was conducted using sulfuric acid at the concentrations of 1 mol L -1 (KA-01), 2 mol L -1 (KA-02) and 5 mol L -1 (KA-05) at 85 °C. The obtained adsorbents were characterized by X-ray fluorescence, X-ray diffraction, N 2 adsorption/desorption isotherms, zeta potential analysis and infrared spectroscopy. The Response Surface Method was used to optimize adsorption parameters (initial concentration of etheramine, adsorbent mass and pH of the solution). The results, described by means of a central composite design, were adjusted to the quadratic model. Results revealed that the adsorption was more efficient at the etheramine concentration of 400 mg L -1 , pH 10 and adsorbent mass of 0.1 g for NK and 0.2 g for KA-01, KA-02 and KA-05. The sample KA-02 presented a significant increase of etheramine removal compared to the NK sample. The adsorption kinetics conducted under optimized conditions showed that the system reached the equilibrium in approximately 30 min. The kinetic data were better adjusted to the pseudo-second order model. The isotherm data revealed that the Sips model was the most adequate one. The calculation of E ads allowed to infer that the mechanism for etheramine removal in all the evaluated samples was chemisorption. The reuse tests showed that, after four uses, the efficiency of adsorbents in removing etheramine did not suffer significant modifications, which makes the use of kaolinite to treat effluents from the reverse flotation of iron ore feasible. Copyright © 2017 Elsevier Ltd. All rights reserved.

Differential capacity of kaolinite and birnessite to protect surface associated proteins against thermal degradation [Fate of protein at mineral surfaces: influence of protein characteristics mineralogy, pH, and energy input

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chacon, Stephany S.; Garcia-Jaramillo, Manuel; Liu, Suet Yi

We report it is widely accepted that soil organic carbon cycling depends on the presence and catalytic functionality of extracellular enzymes. Recent reports suggest that combusted and autoclaved soils may have the capacity to degrade organic test substrates to a larger extent than the living, enzyme-bearing soils. In search of the underlying mechanisms, we adsorbed Beta-Glucosidase (BG) and Bovine Serum Albumin (BSA) on the phyllosilicate kaolinite and the manganese oxide birnessite at pH 5 and pH 7. The protein-mineral samples were then subjected to gradual energy inputs of a magnitude equivalent to naturally occurring wildfire events. The abundance and molecularmore » masses of desorbed organic compounds were recorded after ionization with tunable synchrotron vacuum ultraviolet radiation (VUV). The mechanisms controlling the fate of proteins varied with mineralogy. Kaolinite adsorbed protein largely through hydrophobic interactions and, even at large energy inputs, produced negligible amounts of desorption fragments compared to birnessite. Acid birnessite adsorbed protein through coulombic forces at low energy levels, became a hydrolyzing catalyst at low energies and low pH, and eventually turned into a reactant involving disintegration of both mineral and protein at higher energy inputs. Fragmentation of proteins was energy dependent and did not occur below an energy threshold of 0.20 MW cm -2 . Neither signal abundance nor signal intensity were a function of protein size. Above the energy threshold value, BG that had been adsorbed to birnessite at pH 7 showed an increase in signal abundance with increasing energy applications. Signal intensities differed with adsorption pH for BSA but only at the highest energy level applied. Our results indicate that proteins adsorbed to kaolinite may remain intact after exposure to such energy inputs as can be expected to occur in natural ecosystems. Protein fragmentation and concomitant loss of functionality must be

Development of Dielectric Material with Ceramic Matrix Composite (CMC) Produced from Kaolinite and CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin, Wong Swee; Hassan, Jumiah; Hashim, Mansor

Ceramic matrix composites (CMC) combine reinforcing ceramic phases, CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) with a ceramic matrix, kaolinite to create materials with new and superior properties. 10% and 20% CCTO were prepared by using a conventional solid state reaction method. CMC samples were pre-sintered at 800 deg. C and sintered at 1000 deg. C. The dielectric properties of samples were measured using HP 4192A LF Impedance Analyzer. Microstructures of the samples were observed using an optical microscope. XRD was used to determine the crystalline structure of the samples. The AFM showed the morphology of the samples. The results showed thatmore » the dielectric constant and dielectric loss factor of both samples are frequency dependent. At 10 Hz, the dielectric constant is 10{sup 11} for both samples. The CMC samples were independent with temperature with low dielectric constant in the frequency range of 10{sup 4}-10{sup 6} Hz. Since the CMC samples consist of different amount of kaolinite, so each sample exhibit different defect mechanism. Different reaction may occur for different composition of material. The effects of processing conditions on the microstructure and electrical properties of CMC are also discussed.« less

Molecular Dynamics Simulation of Resin Adsorption at Kaolinite Edge Sites: Effect of Surface Deprotonation on Interfacial Structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zeitler, T. R.; Greathouse, J. A.; Cygan, R. T.

Low-salinity water flooding, a method of enhanced oil recovery, consists of injecting low ionic strength fluids into an oil reservoir in order to detach oil from mineral surfaces in the underlying formation. Although highly successful in practice, the approach is not completely understood at the molecular scale. Molecular dynamics simulations have been used to investigate the effect of surface protonation on the adsorption of an anionic crude oil component on clay mineral edge surfaces. A set of interatomic potentials appropriate for edge simulations has been applied to the kaolinite (010) surface in contact with an aqueous nanopore. Decahydro-2-napthoic acid inmore » its deprotonated form (DHNA –) was used as a representative resin component of crude oil, with monovalent and divalent counterions, to test the observed trends in low-salinity water flooding experiments. Surface models include fully protonated (neutral) and deprotonated (negative) edge sites, which require implementation of a new deprotonation scheme. The surface adsorptive properties of the kaolinite edge under neutral and deprotonated conditions have been investigated for low and high DHNA – concentrations with Na + and Ca 2+ as counterions. The tendency of DHNA – ions to coordinate with divalent (Ca 2+) rather than monovalent (Na +) ions greatly influences adsorption tendencies of the anion. Additionally, the formation of net positively charged surface sites due to Ca 2+ at deprotonated sites results in increased DHNA – adsorption. Divalent cations such as Ca 2+ are able to efficiently bridge surface sites and organic anions. Replacing those cations with monovalent cations such as Na + diminishes the bridging mechanism, resulting in reduced adsorption of the organic species. As a result, a clear trend of decreased DHNA – adsorption is observed in the simulations as Ca 2+ is replaced by Na + for deprotonated surfaces, as would be expected for oil detachment from reservoir formations

Molecular Dynamics Simulation of Resin Adsorption at Kaolinite Edge Sites: Effect of Surface Deprotonation on Interfacial Structure

DOE PAGES

Zeitler, T. R.; Greathouse, J. A.; Cygan, R. T.; ...

2017-10-05

Low-salinity water flooding, a method of enhanced oil recovery, consists of injecting low ionic strength fluids into an oil reservoir in order to detach oil from mineral surfaces in the underlying formation. Although highly successful in practice, the approach is not completely understood at the molecular scale. Molecular dynamics simulations have been used to investigate the effect of surface protonation on the adsorption of an anionic crude oil component on clay mineral edge surfaces. A set of interatomic potentials appropriate for edge simulations has been applied to the kaolinite (010) surface in contact with an aqueous nanopore. Decahydro-2-napthoic acid inmore » its deprotonated form (DHNA –) was used as a representative resin component of crude oil, with monovalent and divalent counterions, to test the observed trends in low-salinity water flooding experiments. Surface models include fully protonated (neutral) and deprotonated (negative) edge sites, which require implementation of a new deprotonation scheme. The surface adsorptive properties of the kaolinite edge under neutral and deprotonated conditions have been investigated for low and high DHNA – concentrations with Na + and Ca 2+ as counterions. The tendency of DHNA – ions to coordinate with divalent (Ca 2+) rather than monovalent (Na +) ions greatly influences adsorption tendencies of the anion. Additionally, the formation of net positively charged surface sites due to Ca 2+ at deprotonated sites results in increased DHNA – adsorption. Divalent cations such as Ca 2+ are able to efficiently bridge surface sites and organic anions. Replacing those cations with monovalent cations such as Na + diminishes the bridging mechanism, resulting in reduced adsorption of the organic species. As a result, a clear trend of decreased DHNA – adsorption is observed in the simulations as Ca 2+ is replaced by Na + for deprotonated surfaces, as would be expected for oil detachment from reservoir formations

Shallow Water Propagation

DTIC Science & Technology

2013-09-30

HPMM. For these minerals, kaolinite and smectite , the corresponding shear speed estimates are 13 m/s and 0.25 m/s. The third and fourth columns of...representative value for each parameter in two clay minerals, kaolinite and smectite , which are the most common types in marine mud. These values produce...13 m/s for kaolinite and 0.25 m/s for smectite . The third column shows typical ranges of values for h, L, and χ in the two clay types. The fourth

Heterogeneous nucleation of nitric acid trihydrate on clay minerals: relevance to type ia polar stratospheric clouds.

PubMed

Hatch, Courtney D; Gough, Raina V; Toon, Owen B; Tolbert, Margaret A

2008-01-17

Although critical to atmospheric modeling of stratospheric ozone depletion, selective heterogeneous nuclei that promote the formation of Type Ia polar stratospheric clouds (PSCs) are largely unknown. While mineral particles are known to be good ice nuclei, it is currently not clear whether they are also good nuclei for PSCs. In the present study, a high-vacuum chamber equipped with transmission Fourier transform infrared spectroscopy and a quadrupole mass spectrometer was used to study heterogeneous nucleation of nitric acid trihydrate (NAT) on two clay minerals-Na-montmorillonite and kaolinite-as analogs of atmospheric terrestrial and extraterrestrial minerals. The minerals are first coated with a 3:1 supercooled H2O/HNO3 solution prior to the observed nucleation of crystalline NAT. At 220 K, NAT formation was observed at low SNAT values of 12 and 7 on kaolinite and montmorillonite clays, respectively. These are the lowest SNAT values reported in the literature on any substrate. However, NAT nucleation exhibited significant temperature dependence. At lower temperatures, representative of typical polar stratospheric conditions, much higher supersaturations were required before nucleation was observed. Our results suggest that NAT nucleation on mineral particles, not previously treated with sulfuric acid, may not be an important nucleation platform for Type Ia PSCs under normal polar stratospheric conditions.

Effect of mineral surface properties (alumina, kaolinite) on the sorptive fractionation mechanisms of soil fulvic acids: Molecular-scale ESI-MS studies

NASA Astrophysics Data System (ADS)

Fleury, Guillaume; Del Nero, Mirella; Barillon, Rémi

2017-01-01

We addressed the effects of mineral surface properties (kaolinite versus Al-oxide) on the sorption-driven fractionation of a soil fulvic acid (FA) at acidic pH, mainly by means of ESI(-)-FTMS analysis of initial and supernatant solutions of FA sorption batch experiments. The MS data provided clear molecular-scale evidence of distinct mechanisms and molecular parameters controlling the FA fractionation upon its sorption on clay and oxide surfaces, respectively. Identification of sorbing and not-sorbing FA compounds in kaolinite-solution systems revealed a weak fractionation among members of sbnd CO2 series of aliphatics or not-condensed aromatics (NCAs) at pH 3.8, and almost no sorption of poorly-oxygenated polycyclic aromatic compounds (PACs) and NCAs. This first molecular-scale description of a FA fractionation in a clay-solution system suggests that H-bonding with low affinity sites (aluminol/silanol) on the basal planes of the clay particles is the main mechanism of sorption. Due to the predominance of such weak and poorly-selective mechanism, the sorption of aliphatic and NCA molecules bearing oxygenated functionalities was prevented at pH 5, due to dissolved Al competing successfully for their coordination. In contrast, a strong FA fractionation was observed onto alumina, with a preferential retention of PACs and highly-oxygenated aliphatics and NCAs. The major part of the poorly oxygenated aliphatics was left in solution. The sorption degree of NCAs and aliphatics was strongly correlated with molecular acidity. For PACs and poorly-oxygenated NCAs, the sorption was driven by reactions of surface ligand exchange (for the most oxygenated compounds) or by hydrophobic interactions (for the least oxygenated compounds).

Investigation of Cyclodextrin-Enhanced Electrokinetic Soil Remediation. Fate and Transport of Nitroaromatic Contaminants and Cyclodextrin Amendments in Expansive Clays

DTIC Science & Technology

2004-09-01

report increasing adsorption capacity depending on the specific clay type, in the order kaolinite < illite < montmorillonite (11). This finding suggests... kaolinite , illite, and montmorillonite . Finally, there is a wide varia- tion in adsorption constants among the different nitroaromatic compounds...common to micas, chlorites, pyrophyllite, talc, kaolinite , and gibbsite . As is now known, clays typically consist of layered crystalline structures

Sorption of lambda-cyhalothrin, cypermethrin, deltamethrin and fenvalerate to quartz, corundum, kaolinite and montmorillonite.

PubMed

Oudou, H Chaaieri; Hansen, H C Bruun

2002-12-01

Sorption to mineral surfaces may be important for retention and degradation of hydrophobic pesticides in subsoils and aquifers poor in organic matter. In this work the title pyrethroids have been used to investigate selective interactions with the surfaces of four minerals. Sorption of the four pyrethroids was quantified in batch experiments with initial pyrethroid concentrations of 1-100 microg/l. Sorption to centrifuge tubes used in the batch experiments accounted for 25-60% of total sorption. Net sorption was obtained from total sorption after subtracting the amounts of pyrethroids sorbed to centrifuge tubes used. All isotherms could be fitted by the Freundlich equation with n ranging between 0.9 and 1.1. Bonding affinities per unit surface area decreased in the order: corundum > quartz > montmorillonite approximately equal kaolinite. A similar sequence as found for the total surface tension of the minerals. All minerals showed the same selectivity order with respect to sorption affinity of the four pyrethroids: lambda-cyhalothrin > deltamethrin > cypermethrin > fenvalerate, which shows that the most hydrophobic compound is sorbed most strongly. Stereochemical properties of the four pyrethroid formulations may also contribute to the selectivity pattern.

Adsorption of dissolved aluminum on sapphire-c and kaolinite: implications for points of zero charge of clay minerals

PubMed Central

2014-01-01

We have studied the impact of dissolved aluminum on interfacial properties of two aluminum bearing minerals, corundum and kaolinite. The effect of intentionally adding dissolved aluminum on electrokinetic potential of basal plane surfaces of sapphire was studied by streaming potential measurements as a function of pH and was complemented by a second harmonic generation (SHG) study at pH 6. The electrokinetic data show a similar trend as the SHG data, suggesting that the SHG electric field correlates to zeta-potential. A comparable study was carried out on kaolinite particles. In this case electrophoretic mobility was measured as a function of pH. In both systems the addition of dissolved aluminum caused significant changes in the charging behavior. The isoelectric point consistently shifted to higher pH values, the extent of the shift depending on the amount of aluminum present or added. The experimental results imply that published isoelectric points of clay minerals may have been affected by this phenomenon. The presence of dissolved aluminum in experimental studies may be caused by particular pre-treatment methods (such as washing in acids and subsequent adsorption of dissolved aluminum) or even simply by starting a series of measurements from extreme pH (causing dissolution), and subsequently varying the pH in the very same batch. This results in interactions of dissolved aluminum with the target surface. A possible interpretation of the experimental results could be that at low aluminum concentrations adatoms of aluminum (we will refer to adsorbed mineral constituents as adatoms) can form at the sapphire basal plane, which can be rather easily removed. Simultaneously, once the surface has been exposed to sufficiently high aluminum concentration, a visible change of the surface is seen by AFM which is attributed to a surface precipitate that cannot be removed under the conditions employed in the current study. In conclusion, whenever pre-treatment or the

On the Kaolinite Floc Size at the Steady State of Flocculation in a Turbulent Flow

PubMed Central

Zhu, Zhongfan; Wang, Hongrui; Yu, Jingshan; Dou, Jie

2016-01-01

The flocculation of cohesive fine-grained sediment plays an important role in the transport characteristics of pollutants and nutrients absorbed on the surface of sediment in estuarine and coastal waters through the complex processes of sediment transport, deposition, resuspension and consolidation. Many laboratory experiments have been carried out to investigate the influence of different flow shear conditions on the floc size at the steady state of flocculation in the shear flow. Most of these experiments reported that the floc size decreases with increasing shear stresses and used a power law to express this dependence. In this study, we performed a Couette-flow experiment to measure the size of the kaolinite floc through sampling observation and an image analysis system at the steady state of flocculation under six flow shear conditions. The results show that the negative correlation of the floc size on the flow shear occurs only at high shear conditions, whereas at low shear conditions, the floc size increases with increasing turbulent shear stresses regardless of electrolyte conditions. Increasing electrolyte conditions and the initial particle concentration could lead to a larger steady-state floc size. PMID:26901652

On the Kaolinite Floc Size at the Steady State of Flocculation in a Turbulent Flow.

PubMed

Zhu, Zhongfan; Wang, Hongrui; Yu, Jingshan; Dou, Jie

2016-01-01

The flocculation of cohesive fine-grained sediment plays an important role in the transport characteristics of pollutants and nutrients absorbed on the surface of sediment in estuarine and coastal waters through the complex processes of sediment transport, deposition, resuspension and consolidation. Many laboratory experiments have been carried out to investigate the influence of different flow shear conditions on the floc size at the steady state of flocculation in the shear flow. Most of these experiments reported that the floc size decreases with increasing shear stresses and used a power law to express this dependence. In this study, we performed a Couette-flow experiment to measure the size of the kaolinite floc through sampling observation and an image analysis system at the steady state of flocculation under six flow shear conditions. The results show that the negative correlation of the floc size on the flow shear occurs only at high shear conditions, whereas at low shear conditions, the floc size increases with increasing turbulent shear stresses regardless of electrolyte conditions. Increasing electrolyte conditions and the initial particle concentration could lead to a larger steady-state floc size.

Strain Rate and Stress Relaxation Effects on Pressuremeter Testing in Clays

DTIC Science & Technology

1992-03-01

CHARACTERISTICS OF KAOLINITE AND GROUND SILICA 245 APPENDIX E COMPUTER PROGRAMS ....................... 248 0 0 0 0 0 0 0 iv LIST OF TABLES Table Page 3.1 A...Comparison of Three Types of Boundary Conditions in a Multiaxial Cubical Test Apparatus ................... 37 3.2 Properties of the Kaolinite and Kaolin...to 0.01 %/min Versus Strain Rate for Kaolinite Clay ................... 102 4.3 Shear Strength Normalized with Respect to 0.01 %/min Versus Strain Rate

Clay mineral type effect on bacterial enteropathogen survival in soil.

PubMed

Brennan, Fiona P; Moynihan, Emma; Griffiths, Bryan S; Hillier, Stephen; Owen, Jason; Pendlowski, Helen; Avery, Lisa M

2014-01-15

Enteropathogens released into the environment can represent a serious risk to public health. Soil clay content has long been known to have an important effect on enteropathogen survival in soil, generally enhancing survival. However, clay mineral composition in soils varies, and different clay minerals have specific physiochemical properties that would be expected to impact differentially on survival. This work investigated the effect of clay materials, with a predominance of a particular mineral type (montmorillonite, kaolinite, or illite), on the survival in soil microcosms over 96 days of Listeria monocytogenes, Salmonella Dublin, and Escherichia coli O157. Clay mineral addition was found to alter a number of physicochemical parameters in soil, including cation exchange capacity and surface area, and this was specific to the mineral type. Clay mineral addition enhanced enteropathogen survival in soil. The type of clay mineral was found to differentially affect enteropathogen survival and the effect was enteropathogen-specific. © 2013.

Effects of Kaolinite (Macsumsuk) and Herb Mixtures on the Quality and Physicochemical Properties of Pork

PubMed Central

Kim, Byung Ki; Hwang, Eun Gyeong; Jung, Dae Jin; Ha, Jae Jung; Oh, Dong Yep

2014-01-01

The current study was conducted to identify technology for the production of high quality pork, based on the meat consumption habits of consumers. Macsumsuk, a type of kaolinite (a clay mineral), and/or a mixture of herbs (Mori Folium, Sophorae Radix, Glycyrrhizae Radix, Citri Leiocarpae Exocarpium, and Pogostemi Herba) were added to the diets of fattening pigs. Sixty barrow pigs (4 kinds of treatment × 5 pigs/treatment × 3 replicates) were randomly assigned to either the Control (no additives), T1 (3% Macsumsuk), T2 (3% Herb mixtures), or T3 (3% Macsumsuk + 3% Herb mixtures) groups, and were fed the diets for 60 d. Dressed weights were in the order of T1 (93.40±4.68kg) > T2 (91.40±6.52kg) > Control (88.80±1.57kg) > T3 (86.80±2.01kg). Back-fat thickness of the Control animals (23.2±1.03) was significantly greater than that of the various treatment groups (p<0.01). Numeric values representing the carcass yield and quality grade were higher for all the treated groups than the Control group, thought the difference was not statistically significant. Crude fat content was significantly higher in the Control group (2.23±0.34%) than in the treated groups (p<0.05). The addition of both Macsumsuk and herb mixtures into the diets of the pigs significantly reduced cooking loss of the pork compared to the Control (p<0.05). No statistically significant changes were observed in the shear force (average 5.87±0.54 kg/cm2), water holding capacity (average 54.59±3.16%), or CIE values of the pork, whereas cholesterol levels significantly decreased (p<0.01) in those fed Macsumsuk and/or the herb mixtures. No significant changes in fatty acid composition, total saturated fatty acid (SFA), total unsaturated fatty acid (UFA), or UFA/SFA ratios were observed by any of the treatments. In conclusion, the results obtained from this study suggest that the addition of Macsumsuk and/or herb mixtures into the diets of growing and fattening pigs improves the pork quality by reducing

Effect of clay type on the velocity and run-out distance of cohesive sediment gravity flows

NASA Astrophysics Data System (ADS)

Baker, Megan; Baas, Jaco H.; Malarkey, Jonathan; Kane, Ian

2016-04-01

Novel laboratory experiments in a lock-exchange flume filled with natural seawater revealed that sediment gravity flows (SGFs) laden with kaolinite clay (weakly cohesive), bentonite clay (strongly cohesive) and silica flour (non-cohesive) have strongly contrasting flow properties. Knowledge of cohesive clay-laden sediment gravity flows is limited, despite clay being one of the most abundant sediment types on earth and subaqueous SGFs transporting the greatest volumes of sediment on our planet. Cohesive SGFs are particularly complex owing to the dynamic interplay between turbulent and cohesive forces. Cohesive forces allow the formation of clay flocs and gels, which increase the viscosity and shear strength of the flow, and attenuate shear-induced turbulence. The experimental SGFs ranged from dilute turbidity currents to dense debris flows. For each experiment, the run-out distance, head velocity and thickness distribution of the deposit were measured, and the flow properties were recorded using high-resolution video. Increasing the volume concentration of kaolinite and bentonite above 22% and 17%, respectively, reduced both the maximum head velocity and the run-out distances of the SGFs. We infer that increasing the concentration of clay particles enhances the opportunity for the particles to collide and flocculate, thus increasing the viscosity and shear strength of the flows at the expense of turbulence, and reducing their forward momentum. Increasing the volume concentration in the silica-flour laden flows from 1% to 46% increased the maximum head velocity, owing to the gradual increase in excess density. Thereafter, however, intergranular friction is inferred to have attenuated the turbulence, causing a rapid reduction in the maximum head velocity and run-out distance as suspended sediment concentration was increased. Moving from flows carrying bentonite via kaolinite to silica flour, a progressively larger volumetric suspended sediment concentration was needed

Discrimination of hydrothermal alteration mineral assemblages at Virginia City, Nevada, using the airborne imaging spectrometer

NASA Technical Reports Server (NTRS)

Hutsinpiller, Amy

1988-01-01

The purpose of this study is to use airborne imaging spectrometer data to discriminate hydrothermal alteration mineral assemblages associated with silver and gold mineralization at Virginia City, NV. The data is corrected for vertical striping and sample gradients, and converted to flat-field logarithmic residuals. Log residual spectra from areas known to be altered are compared to field spectra for kaolinitic, illitic, sericitic, and propylitic alteration types. The areal distributions of these alteration types are estimated using a spectral matching technique. Both visual examination of spectra and the matching techniques are effective in distinguishing kaolinitic, illitic, and propylitic alteration types from each other. However, illitic and sericitic alteration cannot be separated using these techniques because the spectra of illite and sericite are very similar. A principal components analysis of 14 channels in the 2.14-2.38 micron wavelength region is also successful in discriminating and mapping illitic, kaolinitic, and propylitic alteration types.

Interactions Between Suspended Kaolinite Deposition and Hyporheic Exchange Flux Under Losing and Gaining Flow Conditions

NASA Astrophysics Data System (ADS)

Fox, Aryeh; Packman, Aaron I.; Boano, Fulvio; Phillips, Colin B.; Arnon, Shai

2018-05-01

Fine particle deposition and streambed clogging affect many ecological and biogeochemical processes, but little is known about the effects of groundwater flow into and out of rivers on clogging. We evaluated the effects of losing and gaining flow on the deposition of suspended kaolinite clay particles in a sand streambed and the resulting changes in rates and patterns of hyporheic exchange flux (HEF). Observations of clay deposition from the water column, clay accumulation in the streambed sediments, and water exchange with the bed demonstrated that clay deposition in the bed substantially reduced both HEF and the size of the hyporheic zone. Clay deposition and HEF were strongly coupled, leading to rapid clogging in areas of water and clay influx into the bed. Local clogging diverted exchanged water laterally, producing clay deposit layers that reduced vertical hyporheic flow and favored horizontal flow. Under gaining conditions, HEF was spatially constrained by upwelling water, which focused clay deposition in a small region on the upstream side of each bed form. Because the area of inflow into the bed was smallest under gaining conditions, local clogging required less clay mass under gaining conditions than neutral or losing conditions. These results indicate that losing and gaining flow conditions need to be considered in assessments of hyporheic exchange, fine particle dynamics in streams, and streambed clogging and restoration.

Characterization of the surface charge distribution on kaolinite particles using high resolution atomic force microscopy

NASA Astrophysics Data System (ADS)

Kumar, Naveen; Zhao, Cunlu; Klaassen, Aram; van den Ende, Dirk; Mugele, Frieder; Siretanu, Igor

2016-02-01

Most solid surfaces, in particular clay minerals and rock surfaces, acquire a surface charge upon exposure to an aqueous environment due to adsorption and/or desorption of ionic species. Macroscopic techniques such as titration and electrokinetic measurements are commonly used to determine the surface charge and ζ -potential of these surfaces. However, because of the macroscopic averaging character these techniques cannot do justice to the role of local heterogeneities on the surfaces. In this work, we use dynamic atomic force microscopy (AFM) to determine the distribution of surface charge on the two (gibbsite-like and silica-like) basal planes of kaolinite nanoparticles immersed in aqueous electrolyte with a lateral resolution of approximately 30 nm. The surface charge density is extracted from force-distance curves using DLVO theory in combination with surface complexation modeling. While the gibbsite-like and the silica-like facet display on average positive and negative surface charge values as expected, our measurements reveal lateral variations of more than a factor of two on seemingly atomically smooth terraces, even if high resolution AFM images clearly reveal the atomic lattice on the surface. These results suggest that simple surface complexation models of clays that attribute a unique surface chemistry and hence homogeneous surface charge densities to basal planes may miss important aspects of real clay surfaces.

Desorption of Mercury(II) on Kaolinite in the Presence of Oxalate or Cysteine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Senevirathna, W. U.; Zhang, Hong; Gu, Baohua

2011-01-01

Sorption and desorption of Hg(II) on clay minerals can impact the biogeochemical cycle and bio- uptake of Hg in aquatic systems. We studied the desorption of Hg(II) on kaolinite in the presence of oxalate or cysteine, representing the ligands with carboxylic and thiol groups of different affinities for Hg(II). The effects of pH (3, 5, 7), ligand concentration (0.25, 1.0 mM), and temperature (15, 25, 35 C) on the Hg(II) desorption were investigated through desorption kinetics. Our study showed that the Hg(II) desorption was pH-dependant. In the absence of any organic ligand, >90% of the previously adsorbed Hg(II) desorbed atmore » pH 3 within 2 h, compared to <10% at pH 7. Similar results were observed in the presence of oxalate, showing that it hardly affected the Hg(II) desorption. Cysteine inhibited the Hg(II) desorption significantly at all the pH tested, especially in the first 80 min with the desorption less than 20%, but it appeared to enhance the Hg(II) desorption afterwards. The effect of ligand concentration on the Hg(II) desorption was small, especially in the presence of oxalate. The effect of temperature on the desorption was nearly insignificant. The effect of the organic acids on the Hg(II) sorption and desorption is explained by the formation of the ternary surface complexes involving the mineral, ligand, and Hg(II). The competition for Hg(II) between the cysteine molecules adsorbed on the particles and in the solution probably can also affect the Hg(II) desorption.« less

Copper(II) adsorption on the kaolinite(001) surface: Insights from first-principles calculations and molecular dynamics simulations

NASA Astrophysics Data System (ADS)

Kong, Xiang-Ping; Wang, Juan

2016-12-01

The adsorption behavior of Cu(II) on the basal hydroxylated kaolinite(001) surface in aqueous environment was investigated by first-principles calculations and molecular dynamics simulations. Structures of possible monodentate and bidentate inner-sphere adsorption complexes of Cu(II) were examined, and the charge transfer and bonding mechanism were analyzed. Combining the binding energy of complex, the radial distribution function of Cu(II) with oxygen and the extended X-ray absorption fine structure data, monodentate complex on site of surface oxygen with ;upright; hydrogen and bidentate complex on site of two oxygens (one with ;upright; hydrogen and one with ;lying; hydrogen) of single Al center have been found to be the major adsorption species of Cu(II). Both adsorption species are four-coordinated with a square planar geometry. The distribution of surface hydroxyls with ;lying; hydrogen around Cu(II) plays a key role in the structure and stability of adsorption complex. Upon the Mulliken population analysis and partial density of states, charge transfer occurs with Cu(II) accepting some electrons from both surface oxygens and aqua oxygens, and the bonding Cu 3d-O 2p state filling is primarily responsible for the strong covalent interaction of Cu(II) with surface oxygen.

Highly efficient fluoride adsorption from aqueous solution by nepheline prepared from kaolinite through alkali-hydrothermal process.

PubMed

Wang, Hao; Feng, Qiming; Liu, Kun; Li, Zishun; Tang, Xuekun; Li, Guangze

2017-07-01

A direct alkali-hydrothermal induced transformation process was adopted to prepare nepheline from raw kaolinite (shortened form RK in this paper) and NaOH solution in this paper. Structure and morphology characterizations of the synthetic product showed that the nepheline possessed high degree of crystallinity and uniform surface morphology. Specific surface area of nepheline is 18 m 2 /g, with a point of zero charge at around pH 5.0-5.5. The fluoride (F - ions) adsorption by the synthetic nepheline (shortened form SN in this paper) from aqueous solution was also investigated under different experimental conditions. The adsorption process well matched the Langmuir isotherm model with an amazing maximum adsorption capacity of 183 mg/g at 323 K. The thermodynamic parameters (ΔG 0 , ΔH 0 , and ΔS 0 ) for adsorption on SN were also determined from the temperature dependence. The adsorption capacities of fluoride on SN increased with increasing of temperature and initial concentration. Initial pH value also had influence on adsorption process. Adsorption of fluoride was rapidly increased in 5-60 min and thereafter increased slowly to reach the equilibrium in about 90-180 min under all conditions. The adsorption followed a pseudo-second order rate law. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intercalated hybrid of kaolinite with KH2PO4 showing high ionic conductivity (∼10-4 S cm-1) at room temperature

NASA Astrophysics Data System (ADS)

Liu, Shao-Xian; Xue, Chen; Yang, Hao; Huang, Xiao-Qing; Zou, Yang; Ding, Yan-Ni; Li, Li; Ren, Xiao-Ming

2017-12-01

In this paper, we present the study of preparation and ionic conductance for an intercalated hybrid of kaolinite with potassium dihydrogen. The intercalation efficiency is high up to ca. 90%. The intercalated hybrid has been characterized by powder X-ray diffraction, infrared spectroscopy, and thermogravimetric analysis. The ionic conductivity (σ) of the hybrid material is strongly dependent on the moisture in the environment, with σ = 8.4 × 10-10 S cm-1 at 293 K and gradually increases to 7.16 × 10-9 S cm-1 under N2 atmosphere (anhydrous environment) at 353 K as well as an activation energy of Ea = 0.618 e V, whereas σ = 2.19 × 10-4 S cm-1 at 100% relative humidity and 293 K with Ea = 0.44 eV. The mechanism that the moisture affects the ionic conductance of the intercalated hybrid is further discussed.

Influence of clay particles on the transport and retention of titanium dioxide nanoparticles in quartz sand.

PubMed

Cai, Li; Tong, Meiping; Wang, Xueting; Kim, Hyunjung

2014-07-01

This study investigated the influence of two representative suspended clay particles, bentonite and kaolinite, on the transport of titanium dioxide nanoparticles (nTiO2) in saturated quartz sand in both NaCl (1 and 10 mM ionic strength) and CaCl2 solutions (0.1 and 1 mM ionic strength) at pH 7. The breakthrough curves of nTiO2 with bentonite or kaolinite were higher than those without the presence of clay particles in NaCl solutions, indicating that both types of clay particles increased nTiO2 transport in NaCl solutions. Moreover, the enhancement of nTiO2 transport was more significant when bentonite was present in nTiO2 suspensions relative to kaolinite. Similar to NaCl solutions, in CaCl2 solutions, the breakthrough curves of nTiO2 with bentonite were also higher than those without clay particles, while the breakthrough curves of nTiO2 with kaolinite were lower than those without clay particles. Clearly, in CaCl2 solutions, the presence of bentonite in suspensions increased nTiO2 transport, whereas, kaolinite decreased nTiO2 transport in quartz sand. The attachment of nTiO2 onto clay particles (both bentonite and kaolinite) were observed under all experimental conditions. The increased transport of nTiO2 in most experimental conditions (except for kaolinite in CaCl2 solutions) was attributed mainly to the clay-facilitated nTiO2 transport. The straining of larger nTiO2-kaolinite clusters yet contributed to the decreased transport (enhanced retention) of nTiO2 in divalent CaCl2 solutions when kaolinite particles were copresent in suspensions.

Toxic metal immobilization in contaminated sediment using bentonite- and kaolinite-supported nano zero-valent iron

NASA Astrophysics Data System (ADS)

Tomašević, D. D.; Kozma, G.; Kerkez, Dj. V.; Dalmacija, B. D.; Dalmacija, M. B.; Bečelić-Tomin, M. R.; Kukovecz, Á.; Kónya, Z.; Rončević, S.

2014-08-01

The objective of this study was to investigate the possibility of using supported nanoscale zero-valent iron with bentonite and kaolinite for immobilization of As, Pb and Zn in contaminated sediment from the Nadela river basin (Serbia). Assessment of the sediment quality based on the pseudo-total metal content (As, Pb and Zn) according to the corresponding Serbian standards shows its severe contamination, such that it requires disposal in special reservoirs and, if possible, remediation. A microwave-assisted sequential extraction procedure was employed to assess potential metal mobility and risk to the aquatic environment. According to these results, As showed lower risk to the environment than Pb and Zn, which both represent higher risk to the environment. The contaminated sediment, irrespective of the different speciation of the treated metals, was subjected to the same treatment. Semi-dynamic leaching test, based on leachability index and effective diffusion coefficients, was conducted for As-, Pb- and Zn-contaminated sediments in order to assess the long-term leaching behaviour. In order to simulate "worst case" leaching conditions, the test was modified using acetic and humic acid solution as leachants instead of deionized water. A diffusion-based model was used to elucidate the controlling leaching mechanisms; in the majority of samples, the controlling leaching mechanism appeared to be diffusion. Three different single-step leaching tests were applied to evaluate the extraction potential of examined metals. Generally, the test results indicated that the treated sediment is safe for disposal and could even be considered for "controlled utilization".

A Quantitative Geochemical, Mineralogical and Physical Study of Some Selected Rock Weathering Profiles from Brazil

DTIC Science & Technology

1977-08-17

weather to gibbsite (plus or minus iron oxides) in well-drained, and smectite in poorly-drained, environments. Kaolinite found in the vicinity of quartz...rock and completely weathered saprolite. Quartz-rich rock types exhibit wide, gradational weathered zones and usually form kaolinite or halloysite in...free rocks is either formed by re-silication of gibbsite , or is of secondary origin (transported). Texture of the rock (aphanitic vs. phaneric) has

Kaolinite-supported nanoscale zero-valent iron for removal of Pb2+ from aqueous solution: reactivity, characterization and mechanism.

PubMed

Zhang, Xin; Lin, Shen; Chen, Zuliang; Megharaj, Mallavarapu; Naidu, Ravendra

2011-05-01

The use of nanoscale zero-valent iron (nZVI) to remediate contaminated groundwater is limited due to its lack of durability and mechanical strength. To address this issue, 20% (w/w) nZVI was loaded onto kaolinite as a support material (K-nZVI). More than 96% of Pb(2+) was removed from aqueous solution using K-nZVI at an initial condition of 500 mg/L Pb(2+) within 30 min under the conditions of 10 g/L of K-nZVI, pH 5.10 and a temperature of 30 °C. To understand the mechanism of removal of Pb(2+), various techniques were implemented to characterize K-nZVI. Scanning electron microscopy (SEM) indicated that K-nZVI had a suitable dispersive state with a lower aggregation, where the mean specific surface area and average particle size as determined by the BET-N(2) method and X-ray diffraction (XRD), were 26.11 m(2)/g and 44.3 nm, respectively. The results obtained from XRD, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) indicated that a small number of iron oxides formed on the surface of K-nZVI, suggesting that free Pb(2+) was adsorbed onto K-nZVI and subsequently reduced to Pb(0). Copyright © 2011 Elsevier Ltd. All rights reserved.

Sorption specificity and desorption hysteresis of gibberellic acid on ferrihydrite compared to goethite, hematite, montmorillonite, and kaolinite.

PubMed

Zhang, Li; Liu, Fei; Chen, Liang

2017-08-01

The pesticide gibberellic acid (GA 3 ) is a potential endocrine disruptor and environmental toxin; therefore, research into its environmental fate is warranted. Batch studies were conducted to investigate the sorption and desorption characteristics of GA 3 on aquifer media. The results demonstrated special sorption characteristic of GA 3 on ferrihydrite compared to goethite, hematite, montmorillonite, and kaolinite, where the sorption kinetics of GA 3 on ferrihydrite was fitted well with the pseudo-second-order, Elovich, and intra-particle diffusion models. The sorption kinetics of GA 3 on ferrihydrite indicated an initial high sorption rate followed by a slow reaction process. The initial high GA 3 sorption rate may be related to electrostatic sorption and surface complexation reactions on the outer surfaces and at the macropore entrances of ferrihydrite. While the slow step was controlled by GA 3 diffusion into mesopore of ferrihydrite. Analysis of the desorption hysteresis indicated a high hysteresis index (HI) ranging from 0.68 to 17.32, and a low desorption percentage ranging from 18 to 48%. After sufficient desorption, the calculated maximum residual GA 3 quantity due to surface complexation reactions with the ferrihydrite coordinated unsaturated sites was 9.05 ± 0.12 mg g -1 . The calculated maximum quantity of GA 3 trapped within the mesopore was 16.23 ± 0.91 mg g -1 . Graphical Abstract Schematic overview of GA 3 sorption and desorption on five minerals in groundwater.

Development of Surface Complexation Models of Cr(VI) Adsorption on Soils, Sediments and Model Mixtures of Kaolinite, Montmorillonite, γ-Alumina, Hydrous Manganese and Ferric Oxides and Goethite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koretsky, Carla

Hexavalent chromium is a highly toxic contaminant that has been introduced into aquifers and shallow sediments and soils via many anthropogenic activities. Hexavalent chromium contamination is a problem or potential problem in the shallow subsurface at several DOE sites, including Hanford, Idaho National Laboratory, Los Alamos National Laboratory and the Oak Ridge Reservation (DOE, 2008). To accurately quantify the fate and transport of hexavalent chromium at DOE and other contaminated sites, robust geochemical models, capable of correctly predicting changes in chromium chemical form resulting from chemical reactions occurring in subsurface environments are needed. One important chemical reaction that may greatlymore » impact the bioavailability and mobility of hexavalent chromium in the subsurface is chemical binding to the surfaces of particulates, termed adsorption or surface complexation. Quantitative thermodynamic surface complexation models have been derived that can correctly calculate hexavalent chromium adsorption on well-characterized materials over ranges in subsurface conditions, such pH and salinity. However, models have not yet been developed for hexavalent chromium adsorption on many important constituents of natural soils and sediments, such as clay minerals. Furthermore, most of the existing thermodynamic models have been developed for relatively simple, single solid systems and have rarely been tested for the complex mixtures of solids present in real sediments and soils. In this study, the adsorption of hexavalent chromium was measured as a function of pH (3-10), salinity (0.001 to 0.1 M NaNO3), and partial pressure of carbon dioxide(0-5%) on a suite of naturally-occurring solids including goethite (FeOOH), hydrous manganese oxide (MnOOH), hydrous ferric oxide (Fe(OH)3), γ-alumina (Al2O3), kaolinite (Al2Si2O5(OH)4), and montmorillonite (Na3(Al, Mg)2Si4O10(OH)2-nH2O). The results show that all of these materials can bind substantial quantities

Carbonation of Clay Minerals Exposed to scCO2/Water at 200 degrees and 250 degrees C

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sugama, T.; Ecker, L.; Gill, S.

2010-11-01

To clarify the mechanisms of carbonation of clay minerals, such as bentonite, kaolinite, and soft clay, we exposed them to supercritical carbon dioxide (scCO2)/water at temperatures of 200 and 250 C and pressures of 1500 and 2000 psi for 72- and 107-hours. Bentonite, comprising three crystalline phases, montmorillonite (MMT), anorthoclase-type albite, and quartz was susceptible to reactions with ionic carbonic acid yielded by the interactions between scCO2 and water, particularly MMT and anorthoclase-type albite phases. For MMT, the cation-exchangeable ions, such as Na+ and Ca2+, present in its basal interplanar space, were replaced by proton, H+, from ionic carbonic acid;more » thereafter, the cations leaching from MMT directly reacted with CO32- as a counter ion of H+ to form carbonate compounds. Such in-situ carbonation process in basal space caused the shrinkage and breakage of the spacing structure within MMT. In contrast, the wet carbonation of anorthoclase-type albite, categorized as rock minerals, entailed the formation of three amorphous by-products, such as carbonates, kaolinite-like compounds, and silicon dioxide. Together, these two different carbonations caused the disintegration and corruption of bentonite. Kaolinite clay containing the amorphous carbonates and silicon dioxide was inert to wet carbonation. We noted only a gain in weight due to its water uptake, suggesting that kaolinite-like by-products generated by the wet carbonation of rock minerals might remain unchanged even during extended exposure. Soft clay consisting of two crystalline phases, dolomite and silicon dioxide, also was unaltered by wet carbonation, despite the uptake of water.« less

Clay mineralogy of weathering profiles from the Carolina Piedmont.

USGS Publications Warehouse

Loferski, P.J.

1981-01-01

Saprolite profiles (12) that formed over various crystalline rocks from the Charlotte 1o X 2o quadrangle showed overall similarity in their clay mineralogy to depths of 6 to 45 m indicating control by weathering processes rather than by rock type. Most saprolite contained 10-25% clay, and ranged 3 to 70%. Kaolinite and halloysite composed = or >75% of the clay fraction of most samples. The ratio kaolinite:halloysite ranged widely, from 95% kaolinite to 90% halloysite, independent of depth. Clay-size mica was present in all profiles, and ranged 5-75% over a sericite schist. Mixed-layer mica-smectite and mica-vermiculite were subordinate; discrete smectite and vermiculite were rare. The abundance of halloysite indicates a continuously humid environment since the time of profile formation, because of the rapidity with which halloysite dehydrates irreversibly. -R.S.M.

Stratigraphic and climatic implications of clay mineral changes around the Paleocene/Eocene boundary of the northeastern US margin

USGS Publications Warehouse

Gibson, T.G.; Bybell, L.M.; Mason, D.B.

2000-01-01

Kaolinite usually is present in relatively small amounts in most upper Paleocene and lower Eocene neritic deposits of the northern US Atlantic Coastal Plain. However, there is a short period (less than 200,000 k.y.) in the latest Paleocene (upper part of calcareous nannoplankton Zone NP 9) when kaolinite-dominated clay mineral suites replaced the usual illite/smectite-dominated suites. During this time of global biotic and lithologic changes, kaolinite increased from less than 5% of the clay mineral suite to peak proportions of 50-60% of the suite and then returned to less than 5% in uppermost Paleocene/lowermost Eocene strata. This kaolinite pulse is present at numerous localities from southern Virginia to New Jersey. These sites represent both inner and middle neritic depositional environments and reflect input from several river drainage systems. Thus, it is inferred that kaolinite-rich source areas were widespread in the northeastern US during the latest Paleocene. Erosion of these source areas contributed the kaolinite that was transported and widely dispersed into shelf environments of the Salisbury embayment. The kaolinite increase, which occurred during a time of relatively high sea level, probably is the result of intensified weathering due to increased temperature and precipitation. The southern extent of the kaolinite pulse is uncertain in that uppermost Paleocene beds have not been identified in the southern Atlantic Coastal Plain. The late Paleocene kaolinite pulse that consists of an increase to peak kaolinite levels followed by a decrease can be used for detailed correlation between more upbasin and more downbasin sections in the Salisbury embayment. Correlations show that more upbasin Paleocene/Eocene boundary sections are erosionally truncated. They have varying portions of the kaolinite increase and, if present at all, discontinuous portions of the subsequent kaolinite decrease. As these truncated sections are disconformably overlain by lower

Sorption of Hydrophobic Organic Compounds on Natural Sorbents and Organoclays from Aqueous and Non-Aqueous Solutions: A Mini-Review

PubMed Central

Moyo, Francis; Tandlich, Roman; Wilhelmi, Brendan S.; Balaz, Stefan

2014-01-01

Renewed focus on the sorption of hydrophobic organic chemicals (HOCs) onto mineral surfaces and soil components is required due to the increased and wider range of organic pollutants being released into the environment. This mini-review examines the possibility of the contribution and mechanism of HOC sorption onto clay mineral sorbents such as kaolinite, and soil organic matter and the possible role of both in the prevention of environmental contamination by HOCs. Literature data indicates that certain siloxane surfaces can be hydrophobic. Therefore soils can retain HOCs even at low soil organic levels and the extent will depend on the structure of the pollutant and the type and concentration of clay minerals in the sorbent. Clay minerals are wettable by nonpolar solvents and so sorption of HOCs onto them from aqueous and non-aqueous solutions is possible. This is important for two reasons: firstly, the movement and remediation of soil environments will be a function of the concentration and type of clay minerals in the soil. Secondly, low-cost sorbents such as kaolinite and expandable clays can be added to soils or contaminated environments as temporary retention barriers for HOCs. Inorganic cations sorbed onto the kaolinite have a strong influence on the rate and extent of sorption of hydrophobic organic pollutants onto kaolinite. Structural sorbate classes that can be retained by the kaolinite matrix are limited by hydrogen bonding between hydroxyl groups of the octahedral alumosilicate sheet and the tetrahedral sheet with silicon. Soil organic carbon plays a key role in the sorption of HOCs onto soils, but the extent will be strongly affected by the structure of the organic soil matter and the presence of soot. Structural characterisation of soil organic matter in a particular soil should be conducted during a particular contamination event. Contamination by mining extractants and antibiotics will require renewed focus on the use of the QSAR approaches in the

Zeta Potential Measurements on Three Clays from Turkey and Effects of Clays on Coal Flotation

PubMed

Hussain; Dem&idot;rc&idot;; özbayoğlu

1996-12-25

There is a growing trend of characterizing coal and coal wastes in order to study the effect of clays present in them during coal washing. Coarse wastes from the Zonguldak Coal Washery, Turkey, were characterized and found to contain kaolinite, illite, and chlorite. These three clays, obtained in almost pure form from various locations in Turkey, have been subjected to X-ray diffraction (XRD) analysis to assess their purity and zeta potential measurements in order to evaluate their properties in terms of their surface charge and point of zero charge (pzc) values. It was found from XRD data that these clays were almost pure and their electrokinetic potential should therefore be representative of their colloidal behavior. All three clay minerals were negatively charged over the range from pH 2.5 to 11. Chlorite and illite have pzc at pH 3 and pH 2.5, respectively, whereas kaolinite has no pzc. The effect of these clays in Zonguldak coal, wastes, and black waters on coal flotation was studied by floating artificial mixtures of Zonguldak clean coal (4.5% ash) and individual clay. The flotation tests on coal/individual clay revealed that each clay influences coal flotation differently according to its type and amount. Illite had the worst effect on coal floated, followed by chlorite and kaolinite. The loss of yield in coal was found to be 18% for kaolinite, 20% for chlorite, and 28% for illite, indicating the worst effect of illite and least for kaolinite during coal flotation.

Environmental effect and genetic influence: a regional cancer predisposition survey in the Zonguldak region of Northwest Turkey

NASA Astrophysics Data System (ADS)

Kadir, Selahattin; Önen-Hall, A. Piril; Aydin, S. Nihal; Yakicier, Cengiz; Akarsu, Nurten; Tuncer, Murat

2008-03-01

The Cretaceous-Eocene volcano-sedimentary units of the Zonguldak region of the western Black Sea consist of subalkaline andesite and tuff, and sandstone dominated by smectite, kaolinite, accessory chlorite, illite, mordenite, and analcime associated with feldspar, quartz, opal-CT, amphibole, and calcite. Kaolinization, chloritization, sericitization, albitization, Fe-Ti-oxidation, and the presence of zeolite, epidote, and illite in andesitic rocks and tuffaceous materials developed as a result of the degradation of a glass shards matrix, enclosed feldspar, and clinopyroxene-type phenocrysts, due to alteration processes. The association of feldspar and glass with smectite and kaolinite, and the suborientation of feldspar-edged, subparallel kaolinite plates to fracture axes may exhibit an authigenic smectite or kaolinite. Increased alteration degree upward in which Al, Fe, and Ti are gained, and Si, Na, K, and Ca are depleted, is due to the alteration following possible diagenesis and hydrothermal activities. Micromorphologically, fibrous mordenite in the altered units and the presence of needle-type chrysotile in the residential buildings in which cancer cases lived were detected. In addition, the segregation pattern of cancer susceptibility in the region strongly suggested an environmental effect and a genetic influence on the increased cancer incidence in the region. The most likely diagnosis was Li-Fraumeni syndrome, which is one of the hereditary cancer predisposition syndromes; however, no mutations were observed in the p53 gene, which is the major cause of Li-Fraumeni syndrome. The micromorphology observed in the altered units in which cancer cases were detected may have a role in the expression of an unidentified gene, but does not explain alone the occurrence of cancer as a primary cause in the region.

Studies on thermal reactions and sintering behaviour of red clays by irreversible dilatometry

NASA Astrophysics Data System (ADS)

Anil, Asha; Misra, S. N.; Misra, N. M.

2018-05-01

Thermal behavior of clays strongly influences that of ceramic bodies made thereof and hence, its study is must for assessing its utility in ceramic products as well as to set the body composition. Irreversible dilatometry is an effective thermal analysis tool for evaluating thermal reactions as well as sintering behavior of clays or clay based ceramic bodies. In this study, irreversible dilatometry of four red clay samples (S, M, R and G) of Gujarat region, which vary in their chemical and mineralogical compositions was carried out using a Dilatometer and compared. Chemical analysis and XRD of red clays were carried out. XRD showed that major clay minerals in S, M and R clays are kaolinite. However, clay marked R and G showed presence of both kaolinite and illite and /muscovite. Presence of non-clay minerals such as hematite, quartz, anatase were also observed in all clays. XRD results were in agreement with chemical analyses results. Rational analyses showed variation in amount of clay and non-clay minerals in red clay samples. Evaluation of dilatometric curves showed that clay marked as S, M and R exhibit patterns typical for kaolinitic clays. Variation in linear expansion (up to 550°C) and shrinkage (above 550°C) between these three clays was found to be related to difference in amount of quartz and kaolinite respectively. However, dilatometric curve of G exhibit a pattern similar to that for an illitic clay. This study confirmed that sintering of investigated kaolinitic and illitic and / muscovitic red clays initiates at above 1060°C and 860°C respectively and this behaviour strongly depends upon type and amount of minerals and their chemical compositions.

Enrofloxacin uptake and retention on different types of clays

NASA Astrophysics Data System (ADS)

Wan, Miao; Li, Zhaohiu; Hong, Hanlie; Wu, Qingfeng

2013-11-01

The adsorption and retention of enrofloxacin (EN) on different types of clays was studied in batch tests under different pH, contact time, and initial concentration conditions. XRD and FTIR analyses were utilized to characterize EN adsorption and to elucidate mechanisms of EN adsorption. The EN adsorption equilibrium followed the Langmuir isotherm and reached capacities of 667, 228 and 20 mmol/kg at pH 4-5 on the montmorillonite (SWy-2), illite (IMt-2), and kaolinite (KGa-1b), respectively. The pseudo-second-order model fitted the EN sorption kinetics well. Although EN had a much lower adsorption capacity on KGa-1b compared to that on the other two clays, the adsorption rate constant was the fastest at 0.73 kg/mmol-h. Cation exchange interaction was attributed to the major mechanism for EN adsorption on SWy-2 and IMt-2, and non-electrostatic interactions attributed to EN adsorption when solution pH was above 7. Intercalation of EN molecules into the interlayer space of SWy-2 was confirmed by the XRD patterns after EN adsorption. In contrast, the basal spacing and intensity remained the same after EN adsorption on IMt-2 and KGa-1b, indicating that the EN adsorption on the non-swelling clays were limited to the external surfaces.

Specific Features of Profile Distribution and Crystallochemistry of Phyllosilicates in Soils of the Cisbaikal Forest-Steppe

NASA Astrophysics Data System (ADS)

Chizhikova, N. P.; Gamzikov, G. P.; Chechetko, E. S.

2018-01-01

The mineralogical composition of agrogray, dark gray, and agro-dark gray soils (Luvic Greyzemic Retic Phaeozems); agro-dark gray residual-calcareous soils (Calcaric Cambic Phaeozems); clay-illuvial agrochernozems (Luvic Chernic Phaeozems); and agrochernozems with migrational-mycelial carbonates (Haplic Chernozems) developed in the forest-steppe of Central Siberia within the Irkutsk Depression has been studied. The clay (<1 μm) fraction separated from these soils consists of mixed-layer minerals with alternating layers of hydromica, smectite, vermiculite, and chlorite; the proportions between them change within the soil profiles. The clay fraction also contains hydromicas, kaolinite, chlorite, and some admixture of the fine-dispersed quartz. Each type of the soils is characterized by its own distribution pattern of clay material with specific alternation of layers in the mixed-layer formations. Mixed-layer minerals of the chlorite-vermiculite type predominate in the upper horizons of texture-differentiated soils. Down the soil profile, the content of mixed-layer mica-smectitic minerals increases. In the clay fraction of arable dark gray-humus soils with residual carbonates, the distribution of the clay fraction and major mineral phases in the soil profile is relatively even. An increased content of well-crystallized kaolinite is typical of these soils. The parent material of agrochernozems has a layered character: the upper horizons are generally depleted of clay, and the middle-profile and lower horizons are characterized by the considerable kaolinite content. In general, the clay material of soils of the Tulun-Irkutsk forest-steppe differs considerably from the clay material of foreststeppe soils developed from loesslike and mantle loams in the European part of Russia. In particular, this difference is seen in the proportions between major mineral phases and between biotitic and muscovitic components, as well as in the degree of crystallinity and behavior of

Kaolinite, illite and quartz dissolution in the karstification of Paleozoic sandstones of the Furnas Formation, Paraná Basin, Southern Brazil

NASA Astrophysics Data System (ADS)

Melo, Mário Sérgio de; Guimarães, Gilson Burigo; Chinelatto, Adilson Luiz; Giannini, Paulo César Fonseca; Pontes, Henrique Simão; Chinelatto, Adriana Scoton Antonio; Atencio, Daniel

2015-11-01

Karstification processes in sandstones of the Furnas Formation, Silurian to Devonian of the Paraná Basin, have been described since the mid-twentieth century. However, some geologists still doubt the idea of true karst in sandstones. Studies carried out in the Campos Gerais region, Paraná State, Southern Brazil, aimed at investigating the nature of erosion processes in Furnas Formation and the role of the dissolution in the development of their notorious erosive features and underground cavities. These studies have led to the recognition of dissolution macro to micro features ('furnas', caves, ponds, sinks, ruiniform relief on cliffs and rocky surfaces, grain corrosion, speleothems, mineral reprecipitation and incrustation). The analysis (scanning electron microscopy, energy dispersive spectrometry and x-ray diffractometry) of sandstones and their alterites has indicated significant dissolution of clay cement along with discrete quartz grain dissolution. This mesodiagenetic cement (kaolinite and illite) is dissolved and reprecipitated as clay minerals with poorly developed crystallinity along with other minerals, such as variscite and minerals of the alunite supergroup, suggesting organic participation in the processes of dissolution and incrustation. The mineral reprecipitation usually forms centimetric speleothems, found in cavities and sheltered rocky surfaces. The cement dissolution associated with other factors (fractures, wet weather, strong hydraulic gradient, antiquity of the landforms) leads to the rock arenisation, the underground erosion and the appearance of the karst features. Carbonate rocks in the basement may locally be increasing the karst forms in the overlying Furnas Formation. The recognition of the karst character of the Furnas Formation sandstones has important implications in the management of underground water resources (increasingly exploited in the region), in the use of the unique geological heritage and in the prevention of geo

Origins and exploration significance of replacement and vein-type alunite deposits in the Marysvale volcanic field, west central Utah.

USGS Publications Warehouse

Cunningham, C.G.; Rye, R.O.; Steven, T.A.; Mehnert, H.H.

1984-01-01

Alunite in the Marysvale volcanic field forms two (three are described) different types of deposits which contrast in appearance and conditions of origin: 1) Replacement deposits are generally fine-grained and formed by near-surface replacement of intermediate-composition volcanic rocks. The deposits form a bead necklace around a monzonite stock. Each deposit is zoned horizontally from alunitic cores to kaolinitic and propylitic envelopes and zoned vertically from pyrite/propylite upward through alunite/jarosite/hematite to a silica cap. Alunite does not extend below 100 m. Sulphur isotope ratios agree with derivation from underlying Mesozoic evaporites. 2) Natroalunite of 14-m.y. age crosscuts replacement-type alunite deposits. Its S-isotope ratios are comparable with those of pyrite in the volcanics. The Na may be from underlying Mesozoic halites. 3) Veins of coarse-grained alunite of 14-m.y. age filled extension fractures above a postulated stock. S-isotope ratios indicate a probable magmatic source. The contrasting properties of the Marysvale alunite deposits preclude any simple relation to ore deposits, but serve to refine interpretations based on other geological considerations. The replacement deposits are a logical near-surface result of skarn forming processes at depth around the monzonite stock. The vein- type deposits are a logical near-surface result of porphyry metallization in an underlying stock. -G.J.N.

Origin, distribution, and rapid removal of hydrothermally formed clay at Mount Baker, Washington

USGS Publications Warehouse

Frank, David

1983-01-01

Clay minerals are locally abundant in two hydrothermal areas at Mount Baker-Sherman Crater and the Dorr Fumarole Field. The silt- and clay-size fractions of volcanic debris that is undergoing alteration at and near the ground surface around areas of current fumarolic activity in Sherman Crater are largely dominated by alunite and a silica phase, either opal or cristobalite, but contain some kaolinite and smectite. Correspondingly, the chemistry of solutions at the surface of the crater, as represented by the crater lake, favors the formation of alunite over kaolinite. In contrast, vent-filling debris that was ejected to the surface from fumaroles in 1975 contains more than 20 percent clay-size material in which kaolinite and smectite are dominant. The youngest eruptive deposit (probably 19th century) on the crater rim was also altered prior to ejection and contains as much as 27 percent clay-size material in which kaolinite, smectite, pyrophyllite, and mixed-layer illitesmectite are abundant. The hydrothermal products, kaolinite and alunite, are present in significant amounts in five large Holocene mudflows that originated at the upper cone of Mount Baker. The distribution of kaolinite in crater and valley deposits indicates that, with the passage of time, increasingly greater amounts of this clay mineral have been incorporated into large mass movements from the upper cone. Either erosion has cut into more kaolinitic parts of the core of Sherman Crater, or the amount of kaolinite has increased through time in Sherman Crater.

Latest Paleocene lithologic and biotic events in neritic deposits of southwestern New Jersey

USGS Publications Warehouse

Gibson, Thomas G.; Bybell, Laurel M.; Owens, James P.

1993-01-01

In the southwestern New Jersey Coastal Plain, four drill holes contain continuous neritic sedimentation across the Paleocene/Eocene boundary (calcareous nannofossil Zone NP 9/NP 10 boundary). Significant lithologic and biotic changes occur in these strata near the top of the Paleocene. Global warming, increased precipitation, and other oceanographic and climatic events that have been recognized in high-latitude, deep-oceanic deposits of the latest Paleocene also influenced mid-latitude, shallow-marine, and terrestrial environments of the western North Atlantic. The diverse, well-preserved calcareous nannofossil flora that is present throughout the entire New Jersey boundary section accurately places these events within the uppermost part of the upper Paleocene Zone NP 9. Several rapid but gradational changes occur within a 1.1-m interval near the top of Zone NP 9. The changes include (1) a change in lithology from glauconitic quartz sand to clay, (2) a change in clay mineral suites from illite/smectite-dominated to kaolinite-dominated, (3) a change in benthic foraminiferal assemblages to a lower diversity fauna suggestive of low-oxygen environments, (4) a significant increase in planktonic foraminiferal abundance, and (5) an increased species turnover rate in marine calcareous nannofossils. Pollen was sparse in the New Jersey drill holes, but terrestrial sporomorph species in Virginia exhibit increased turnover rates at a correlative level. Foraminiferal assemblages and lithology indicate that relative sea level rose in New Jersey at the same time as these late Paleocene events occurred in late Biochron NP 9. The higher sea levels influenced sediment type and absolute abundance of planktonic foraminifers in the deposits. Above the initial increase of kaolinite in the upper part of Zone NP 9, the kaolinite percentage continues to increase, and the maximum kaolinite value occurs in the uppermost part of Zone NP 9. There are few changes in either the sediments or the

Near-infrared reflectance spectra of mixtures of kaolin-group minerals: Use in clay mineral studies

USGS Publications Warehouse

Crowley, James K.; Vergo, Norma

1988-01-01

Near-infrared (NIR) reflectance spectra for mixtures of ordered kaolinite and ordered dickite have been found to simulate the spectral response of disordered kaolinite. The amount of octahedral vacancy disorder in nine disordered kaolinite samples was estimated by comparing the sample spectra to the spectra of reference mixtures. The resulting estimates are consistent with previously published estimates of vacancy disorder for similar kaolin minerals that were modeled from calculated X-ray diffraction patterns. The ordered kaolinite and dickite samples used in the reference mixtures were carefully selected to avoid undesirable particle size effects that could bias the spectral results.NIR spectra were also recorded for laboratory mixtures of ordered kaolinite and halloysite to assess whether the spectra could be potentially useful for determining mineral proportions in natural physical mixtures of these two clays. Although the kaolinite-halloysite proportions could only be roughly estimated from the mixture spectra, the halloysite component was evident even when halloysite was present in only minor amounts. A similar approach using NIR spectra for laboratory mixtures may have applications in other studies of natural clay mixtures.

Provenance analysis and thermo-dynamic studies of multi-type Holocene duricrusts (1700 BC) in the Sua Salt Pan, NE Botswana

NASA Astrophysics Data System (ADS)

Dill, Harald G.; Dohrmann, R.; Kaufhold, S.; Techmer, A.

2014-08-01

Multi-type duricrusts, composed of silcretes, calcretes, halcretes and sulcretes developed during the Holocene at the northern rim of the Sua Salt Pan, NE Botswana. They were investigated for their light (quartz/chalcedony, feldspar, analcime, clinoptilolite, calcite, kaolinite/halloysite, illite-smectite mixed-layers, halite) and heavy minerals (baryte, clinozoisite-epidote s.s.s., amphibole, corundum, tourmaline, ilmenite, rutile, sphene, kyanite, andalusite, staurolite, garnet, zircon, apatite, monazite, cassiterite, garnet, biotite) using petrographic microscopy, X-ray fluorescence and diffraction analyses, radio-carbon dating, scanning electron microscopy equipped with an EDX-system, cation exchange capacity and infrared spectroscopy. Detrital minerals predominantly derived from the erosion of rocks belonging to the Archaean Basement Complex, the Stormberg Volcanites and the Kalahari sediments. Of particular interest to exploration geologists, geikielite-enriched ilmenite fragments are a hint to kimberlitic pipes. Biodetritus was derived from invertebrates and from vertebrates (fish bones?). A man-made impact on the heavy mineral suite has to be invoked from small fragments of cassiterite fragments that derived from processing of sulfidic and pegmatitic Sn-bearing ore. In the salt-pan-derived duricrusts mainly the aeolian and to a lesser degree fluvial inputs were responsible for the concentration of clasts in these multi-type duricrusts. Moreover, their variegated mineralogy enables us to constrain the physical-chemical regime, prevalently as to the pH and the chemical composition of the major constituents. All duricrusts developed in a self-sufficient chemically closed system where quartz and feldspar provided the elements Si, Na, K, Ca, and Ba to produce the encrustations. The spatial and temporal trend in the Sua Salt Pan rim encrustations may be described as follows: (1) sulcrete-silcretes, (2) silcretes with kaolinite-group minerals towards more recent

Oxygen-isotope, X-ray-diffraction and scanning-electron-microscope examinations of authigenic-layer-silicate minerals from Mississippian and Pennsylvanian sandstones in the Michigan Basin

USGS Publications Warehouse

Zacharias, K.F.; Sibley, D.F.; Westjohn, D.B.; Weaver, T. L.

1993-01-01

Oxygen-isotope compositions of authigenic-layer silicates (<2-micrometer fraction) extracted from Mississippian and Pennsylvanian sandstones in the Lower Peninsula of Michigan were determined. Petrographic and scanning-electron-microscope examinations, and X-ray diffractograms show that chlorite and kaolinite are the most common authigenic-layer silicates in Mississippian sandstones. The range of oxygen-isotope compositions of chlorite and kaolinite are +10.3 to +11.9 and +12.9 to +19.3 pars per thousand (per mil) (relative to Standard Mean Ocean Water), respectively. Kaolinite is the only authigenic-isotopic compositions of kaolinite range from +16.8 to +19.0 per mil.

The Weathering of Rocks Under Humid Tropical Conditions.

DTIC Science & Technology

kaolinitic clay, the formation of gibbsite from the kaolinite , and the leaching of silica and iron-oxides. (Modified author abstract)...rhyolitic to andesitic lavas, tuffs and granophyre, under warm humid climatic conditions. The dominant minerals in the bauxite deposits are gibbsite ... kaolinite , quartz (also chalcedony), goethite, and hematite. The occurrence of bauxite is determined primarily by the parent rocks, which are typically fine

K0-Behavior of Normally Consolidated Fine-Grained Soils during One-Dimensional Secondary Compression Aging and the Quantitative Prediction of the Quasi-Preconsolidation Effect.

DTIC Science & Technology

1986-01-01

Plastic Kaolinite and three Agsco novaculite, were allowed to age a minimum of 14 days under 2 tsf vertical stress while the Ko-condition was maintained and...16 3.1 Introduction ................................ 16 3.2 Edgar Plastic Kaolinite ....................... 17 3.3 Novaculite...system are provided. "’Six normally consolidated fine-grained specimens, three Edjar Plastic Kaolinite and three Agsco novaculite, were allowed to

40 CFR 180.910 - Inert ingredients used pre- and post-harvest; exemptions from the requirement of a tolerance.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Solvent Kaolinite-type clay Solid diluent, carrier Lactic acid Solvent Lactic acid, 2-ethylhexyl ester (CAS Reg. No. 6283-86-9) Solvent Lactic acid, 2-ethylhexyl ester, (2S)- (CAS Reg. No. 186817-80-1) Solvent Lactic acid, n-propyl ester, (S); (CAS Reg. No. 53651-69-7) Solvent Lauryl alcohol Surfactant...

Removal of organic pollutants and heavy metals in soils by electrokinetic remediation.

PubMed

Ricart, M T; Pazos, M; Gouveia, S; Cameselle, C; Sanroman, M A

2008-07-01

In this work, the feasibility of electrokinetic remediation for the restoration of polluted soil with organic and inorganic compounds had been development and evaluated using a model soil sample. The model soil was prepared with kaolinite clay artificially polluted in the laboratory with chromium and an azo dye: Reactive Black 5 (RB5). The electromigration of Cr in a spiked kaolinite sample was studied in alkaline conditions. Despite of the high pH registered in the kaolinite sample (around pH 9.5), Cr migrated towards the cathode and it was accumulated in the cathode chamber forming a white precipitate. The removal was not complete, and 23% of the initial Cr was retained into the kaolinite sample close to the cathode side. The azo dye RB5 could be effectively removed from kaolinite by electrokinetics and the complete cleanup of the kaolinite could be achieved in alkaline environment. In this condition, RB5 formed an anion that migrated towards the anode where it was accumulated and quickly degraded upon the electrode surface. The electrokinetic treatment of a kaolinite sample polluted with both Cr and RB5 yielded very good results. The removal of Cr was improved compared to the experiment where Cr was the only pollutant, and RB5 reached a removal as high as 95%. RB5 was removed by electromigration towards the anode, where the dye was degraded upon the surface of the electrode by electrochemical oxidation. Cr was transported towards the cathode by electromigration and electroosmosis. It is supposed that the interaction among RB5 and Cr into the kaolinite sample prevented premature precipitation and allow Cr to migrate and concentrate in the cathode chamber.

Intensity of African Humid Periods Estimated from Saharan Dust Fluxes.

PubMed

Ehrmann, Werner; Schmiedl, Gerhard; Beuscher, Sarah; Krüger, Stefan

2017-01-01

North Africa experienced dramatic changes in hydrology and vegetation during the late Quaternary driven by insolation-induced shifts of the tropical rain belt and further modulated by millennial-scale droughts and vegetation-climate feedbacks. While most past proxy and modelling studies concentrated on the temporal and spatial dynamics of the last African humid period, little is known about the intensities and characteristics of pre-Holocene humid periods. Here we present a high-resolution record of fine-grained eastern Saharan dust from the Eastern Mediterranean Sea spanning the last 180 kyr, which is based on the clay mineral composition of the marine sediments, especially the kaolinite/chlorite ratio. Minimum aeolian kaolinite transport occurred during the African Humid Periods because kaolinite deflation was hampered by increased humidity and vegetation cover. Instead, kaolinite weathering from kaolinite-bearing Cenozoic rocks was stored in lake basins, river beds and soils during these periods. During the subsequent dry phases, fine-grained dust was mobilised from the desiccated lakes, rivers and soils resulting in maximum aeolian uptake and transport of kaolinite. The kaolinite transport decreased again when these sediment sources exhausted. We conclude that the amount of clay-sized dust blown out of the Sahara into the Eastern Mediterranean Sea is proportional to the intensity of the kaolinite weathering and accumulation in soils and lake sediments, and thus to the strength of the preceding humid period. These humid periods provided the windows for the migration of modern humans out of Africa, as postulated previously. The strongest humid period occurred during the Eemian and was followed by two weaker phases centred at ca. 100 ka and ca. 80 ka.

Intensity of African Humid Periods Estimated from Saharan Dust Fluxes

PubMed Central

Ehrmann, Werner; Schmiedl, Gerhard; Beuscher, Sarah; Krüger, Stefan

2017-01-01

North Africa experienced dramatic changes in hydrology and vegetation during the late Quaternary driven by insolation-induced shifts of the tropical rain belt and further modulated by millennial-scale droughts and vegetation-climate feedbacks. While most past proxy and modelling studies concentrated on the temporal and spatial dynamics of the last African humid period, little is known about the intensities and characteristics of pre-Holocene humid periods. Here we present a high-resolution record of fine-grained eastern Saharan dust from the Eastern Mediterranean Sea spanning the last 180 kyr, which is based on the clay mineral composition of the marine sediments, especially the kaolinite/chlorite ratio. Minimum aeolian kaolinite transport occurred during the African Humid Periods because kaolinite deflation was hampered by increased humidity and vegetation cover. Instead, kaolinite weathering from kaolinite-bearing Cenozoic rocks was stored in lake basins, river beds and soils during these periods. During the subsequent dry phases, fine-grained dust was mobilised from the desiccated lakes, rivers and soils resulting in maximum aeolian uptake and transport of kaolinite. The kaolinite transport decreased again when these sediment sources exhausted. We conclude that the amount of clay-sized dust blown out of the Sahara into the Eastern Mediterranean Sea is proportional to the intensity of the kaolinite weathering and accumulation in soils and lake sediments, and thus to the strength of the preceding humid period. These humid periods provided the windows for the migration of modern humans out of Africa, as postulated previously. The strongest humid period occurred during the Eemian and was followed by two weaker phases centred at ca. 100 ka and ca. 80 ka. PMID:28129378

Interface Modeling for Electro-Osmosis in Subgrade Structures

DTIC Science & Technology

2004-12-01

aggregate and different clays ( kaolinite , montmorillonite , limestone and quartz sands) created to simulate below grade structures. A direct current 30...Quartz Sand 100 Sieve Ca Montmorillonite Na Montmorillonite Kaolinite The test setup used a 0.45 water to cement ratio concrete cylinder... Kaolinite cell Figure 4. Measured pH for Concrete and Na Montmorillonite cell 4 Scaling occurred at the interface between the anode

Increase in Ice Nucleation Efficiency of Feldspars, Kaolinite and Mica in Dilute NH3 and NH4+-containing Solutions

NASA Astrophysics Data System (ADS)

Kumar, A.; Marcolli, C.; Luo, B.; Krieger, U. K.; Peter, T.

2017-12-01

Semivolatile species present in the atmosphere are prone to adhere to mineral dust particle surfaces during long range transport, and could potentially change the particle surface properties and its ice nucleation (IN) efficiency. Immersion freezing experiments were performed with microcline (K-feldspar), known to be highly IN active, suspended in aqueous solutions of ammonia, (NH4)2SO4, NH4HSO4, NH4NO3, NH4Cl, Na2SO4, H2SO4, K2SO4 and KCl to investigate the effect of solutes on the IN efficiency. Freezing of emulsified droplets investigated with a differential scanning calorimeter (DSC) showed that the heterogeneous ice nucleation temperatures deviate from the water activity-based IN theory, describing heterogeneous ice nucleation temperatures as a function of solution water activity by a constant offset with respect to the ice melting point curve (Zobrist et al. 2008). IN temperatures enhanced up to 4.5 K were observed for very dilute NH3 and NH4+-containing solutions while a decrease was observed as the concentration was further increased. For all solutes with cations other than NH4+, the IN efficiency decreased. An increase of the IN efficiency in very dilute NH3 and NH4+-containing solutions followed by a decrease with increasing concentration was also observed for sanidine (K-feldspar) and andesine (Na/Ca-feldspar). This is an important indication towards specific chemical interactions between solutes and the feldspar surface which is not captured by the water activity-based IN theory. A similar trend is present but less pronounced in case of kaolinite and mica, while quartz is barely affected. We hypothesize that the hydrogen bonding of NH3 molecules with surface -OH groups could be the reason for the enhanced freezing temperatures in dilute ammonia and ammonium containing solutions as they could form an ice-like overlayer providing hydrogen bonding groups for ice to nucleate on top of it. This implies to possibilities of enhanced IN efficiency, especially

New organophilic kaolin clays based on single-point grafted 3-aminopropyl dimethylethoxysilane.

PubMed

Zaharia, A; Perrin, F-X; Teodorescu, M; Radu, A-L; Iordache, T-V; Florea, A-M; Donescu, D; Sarbu, A

2015-10-14

In this study, the organophilization procedure of kaolin rocks with a monofunctional ethoxysilane- 3 aminopropyl dimethyl ethoxysilane (APMS) is depicted for the first time. The two-step organophilization procedure, including dimethyl sulfoxide intercalation and APMS grafting onto the inner hydroxyl surface of kaolinite (the mineral) layers was tested for three sources of kaolin rocks (KR, KC and KD) with various morphologies and kaolinite compositions. The load of APMS in the kaolinite interlayer space was higher than that of 3-aminopropyl triethoxysilane (APTS) due to the single-point grafting nature of the organophilization reaction. A higher long-distance order of kaolinite layers with low staking was obtained for the APMS, due to a more controllable organiphilization reaction. Last but not least, the solid state (29)Si-NMR tests confirmed the single-point grafting mechanism of APMS, corroborating monodentate fixation on the kaolinite hydroxyl facets, with no contribution to the bidentate or tridentate fixation as observed for APTS.

Preliminary report on the clay mineralogy of the Upper Devonian Shales in the southern and middle Appalachian Basin

USGS Publications Warehouse

Hosterman, John W.; Loferski, Patricia J.

1978-01-01

The distribution of kaolinite in parts of the Devonian shale section is the most significant finding of this work. These shales are composed predominately of 2M illite and illitic mixed-layer clay with minor amounts of chlorite and kaolinite. Preliminary data indicate that kaolinite, the only allogenic clay mineral, is present in successively older beds of the Ohio Shale from south to north in the southern and middle parts of the Appalachian basin. This trend in the distribution of kaolinite shows a paleocurrent direction to the southwest. Three well-known methods of preparing the clay fraction for X-ray diffraction analysis were tested and evaluated. Kaolinite was not identified in two of the methods because of layering due to differing settling rates of the clay minerals. It is suggested that if one of the two settling methods of sample preparation is used, the clay film be thin enough for the X-ray beam to penetrate the entire thickness of clay.

Turbulent Coagulation of Particles Smaller Than the Length Scales of Turbulence and Equilibrium Sorption of Phenanthrene to Clay: Implications for Pollutant Transport in the Estuarine Water Column

DTIC Science & Technology

1997-05-01

estuaries was modeled using phenanthrene, bacterial extracellular polymer and kaolinite clay as surrogates for a hydrophobic organic pollutant...coefficients obtained for phenanthrene sorption to kaolinite and bentonite in the presence of varying amounts of DOM represented by alginic acid and tannic...acid. 333 Table B.3: Literature values for sorption between phenanthrene, humic acid and kaolinite for [DOM]a = 10 mg/L 334 Table E.1: Sample output data

The Influence of Soil Suction on the Shear Strength of Unsaturated Soil

DTIC Science & Technology

1990-09-01

the shear strength parameters c’ and 0’ for montmorillonitic and kaolinitic clays increased following the addition of divalent calcium hydroxide to...503-513. Sridharan, A., Rao, S.N., and Rao, G.V. (1971), "Shear Strength Char- acteristics of Saturated Montmorillonite and Kaolinite Clays," Soils...Summary of Shear Strengths of Unsaturated Specimens of Compacted Kaolinite and Compacted Red Earth (After Murthy, Sridharan and Nagaraj, 1987

Organic Pollutants in Soils, as Studied by Nuclear Magnetic Resonance

DTIC Science & Technology

1998-05-15

represented in most of this study by the ’ following major soil components: humics (humic acid, fulvic acid, humin), clays ( montmorillonite , kaolinite ...fulvic acids and clays ( kaolinite and montmorillonite ). This study was designed to provide the kind of fundamental chemical/physical information...elemental analysis and 29Si and 27A1 NMR data, are a kaolinite and a Ca- montmorillonite obtained from the Missouri Clay Repository, Columbia, MO. Figures

Sorption of Selected Volatile Organic Constituents of Jet Fuels and Solvents on Natural Sorbents from Gas and Solutions Phases

DTIC Science & Technology

1988-08-01

self-supporting films, and aqueous slurries. IR spectra were obtained for kaolinite and montmorillonite clays as well as for p-xylene adsorbed on...proportional to OC and Xs. They also reported that the sorption of chloroethanes on sand, montmorillonite , and kaolinite was too small (< 2 ng/g soil...Ca- montmorillonite and Ca-kaolin at fractional surface coverages of only 0.65 and 0.35, respectively. C values for their montmorillonite and kaolinite

Fines migration during CO 2 injection: Experimental results interpreted using surface forces

DOE PAGES

Xie, Quan; Saeedi, Ali; Delle Piane, Claudio; ...

2017-09-04

The South West Hub project is one of the Australian Flagship Carbon Capture and Storage projects located in the south-west of Western Australia. To evaluate the injectivity potential during the forthcoming full-scale CO 2 injection, we conducted three core-flooding experiments using reservoir core plugs from the well Harvey-1. We aimed to investigate in this paper whether the injection of CO 2 leads to fines migration and permeability reduction due to the relatively high kaolinite content (up to 13%) in the injection interval of the target formation (i.e. the Wonnerup Member of the Lesueur Formation). We imaged the core samples beforemore » flooding to verify the presence of kaolinite at the pore-scale using scanning electron microscopy (SEM). We also examined the pore network of the core plugs before and after the core-flooding experiments using Nuclear Magnetic Resonance (NMR). Moreover, to gain a better understanding of any kaolinite fines migration, we delineated surface force using two models based on Derjaguin-Landau-Verwey-Overbeek (denoted by DLVO) theory coupled hydrodynamic force: (1) sphere/flat model representing interaction between kaolinite/quartz, and (2) flat/flat model representing interaction between kaolinite/kaolinite. Our core-flooding experimental results showed that CO 2/brine injection triggered moderate to significant reduction in the permeability of the core samples with a negligible porosity change. NMR measurements supported the core-flooding results, suggesting that the relatively large pores disappeared in favour of a higher proportion of the medium to small pores after flooding. The DLVO calculations showed that some kaolinite particles probably lifted off and detached from neighbouring kaolinite particles rather than quartz grains. Moreover, the modelling results showed that the kaolinite fines migration would not occur under normal reservoir multiphase flow conditions. This is not because of the low hydrodynamic force. It is

Fines migration during CO 2 injection: Experimental results interpreted using surface forces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Quan; Saeedi, Ali; Delle Piane, Claudio

The South West Hub project is one of the Australian Flagship Carbon Capture and Storage projects located in the south-west of Western Australia. To evaluate the injectivity potential during the forthcoming full-scale CO 2 injection, we conducted three core-flooding experiments using reservoir core plugs from the well Harvey-1. We aimed to investigate in this paper whether the injection of CO 2 leads to fines migration and permeability reduction due to the relatively high kaolinite content (up to 13%) in the injection interval of the target formation (i.e. the Wonnerup Member of the Lesueur Formation). We imaged the core samples beforemore » flooding to verify the presence of kaolinite at the pore-scale using scanning electron microscopy (SEM). We also examined the pore network of the core plugs before and after the core-flooding experiments using Nuclear Magnetic Resonance (NMR). Moreover, to gain a better understanding of any kaolinite fines migration, we delineated surface force using two models based on Derjaguin-Landau-Verwey-Overbeek (denoted by DLVO) theory coupled hydrodynamic force: (1) sphere/flat model representing interaction between kaolinite/quartz, and (2) flat/flat model representing interaction between kaolinite/kaolinite. Our core-flooding experimental results showed that CO 2/brine injection triggered moderate to significant reduction in the permeability of the core samples with a negligible porosity change. NMR measurements supported the core-flooding results, suggesting that the relatively large pores disappeared in favour of a higher proportion of the medium to small pores after flooding. The DLVO calculations showed that some kaolinite particles probably lifted off and detached from neighbouring kaolinite particles rather than quartz grains. Moreover, the modelling results showed that the kaolinite fines migration would not occur under normal reservoir multiphase flow conditions. This is not because of the low hydrodynamic force. It is

Interfacial interaction between methyl parathion-degrading bacteria and minerals is important in biodegradation.

PubMed

Zhao, Gang; Huang, Qiaoyun; Rong, Xingmin; Cai, Peng; Liang, Wei; Dai, Ke

2014-02-01

In the present study, the influence of kaolinite and goethite on microbial degradation of methyl parathion was investigated. We observed that the biodegradation process was improved by kaolinite and depressed by goethite. Calorimetric data further showed that the metabolic activities of degrading cells (Pseudomonas putida) were enhanced by the presence of kaolinite and depressed by the presence of goethite. A semipermeable membrane experiment was performed and results supported the above observations: the promotive effect of kaolinite and the inhibition of goethite for microbial degradation was not found when the bacteria was enclosed by semipermeable membrane and had no direct contact with these minerals, suggesting the important function of the contact of cellular surfaces with mineral particles. The relative larger particles of kaolinite were loosely attached to the bacteria. This attachment made the cells easy to use the sorbed substrate and then stimulated biodegradation. For goethite, small particles were tightly bound to bacterial cells and limited the acquisition of substrate and nutrients, thereby inhibiting biodegradation. These results indicated that interfacial interaction between bacterial cells and minerals significantly affected the biodegradation of pesticides.

A laboratory study of colloid and solute transport in surface runoff on saturated soil

NASA Astrophysics Data System (ADS)

Yu, Congrong; Gao, Bin; Muñoz-Carpena, Rafael; Tian, Yuan; Wu, Lei; Perez-Ovilla, Oscar

2011-05-01

SummaryColloids in surface runoff may pose risks to the ecosystems not only because some of them (e.g., pathogens) are toxic, but also because they may facilitate the transport of other contaminants. Although many studies have been conducted to explore colloid fate and transport in the environment, current understanding of colloids in surface runoff is still limited. In this study, we conducted a range of laboratory experiments to examine the transport behavior of colloids in a surface runoff system, made of a soil box packed with quartz sand with four soil drainage outlets and one surface flow outlet. A natural clay colloid (kaolinite) and a conservative chemical tracer (bromide) were applied to the system under a simulated rainfall event (64 mm/h). Effluent soil drainage and surface flow samples were collected to determine the breakthrough concentrations of bromide and kaolinite. Under the experimental conditions tested, our results showed that surface runoff dominated the transport processes. As a result, kaolinite and bromide were found more in surface flow than in soil drainage. Comparisons between the breakthrough concentrations of bromide and kaolinite showed that kaolinite had lower mobility than bromide in the subsurface flow (i.e., soil drainage), but behaved almost identical to bromide in the surface runoff. Student's t-test confirmed the difference between kaolinite and bromide in subsurface flow ( p = 0.02). Spearman's test and linear regression analysis, however, showed a strong 1:1 correlation between kaolinite and bromide in surface runoff ( p < 0.0001). Our result indicate that colloids and chemical solutes may behave similarly in overland flow on bare soils with limited drainage when surface runoff dominates the transport processes.

Chapter C: Hydrothermal Enrichment of Gallium in Zones of Advanced Argillic Alteration-Examples from the Paradise Peak and McDermitt Ore Deposits, Nevada

USGS Publications Warehouse

Rytuba, James J.; John, David A.; Foster, Andrea; Ludington, Steven D.; Kotlyar, Boris

2003-01-01

Gallium is produced as a byproduct from bauxite and zinc sulfide ores and rarely from primary Ga ores. High Ga contents (>60 ppm) can occur in zones of advanced argillic alteration consisting of alunite+kaolinite+quartz associated with quartz-alunite (high sulfidation Au-Ag) deposits. In a magmatic-hydrothermal environment, the zones of advanced argillic alteration associated with quartz-alunite (high sulfidation) Au-Ag deposits have the highest Ga contents (max 120 ppm). In these Au deposits, Ga is enriched in the zone of alunite+kaolinite alteration and depleted in the zone of quartz-rich alteration within acid-leached rocks. Peripheral zones of argillic alteration have Ga contents and Al/Ga ratios similar to those in unaltered volcanic rocks. The zones of advanced argillic alteration that formed in a steam-heated environment in association with hot-spring-type Hg-Au deposits are not Ga enriched, and residual silicified zones have very low Ga contents. The McDermitt Hg and Paradise Peak Au-Hg deposits, Nev., have zones of advanced argillic alteration that are Ga enriched. At the Paradise Peak Au-Hg deposits, Ga is enriched in the zone of alunite+jarosite alteration that formed in a magmatic-hydrothermal environment. Ga is depleted in the zone of opal+alunite alteration formed in a steam-heated environment, in residual silicified zones formed in a magmatic-hydrothermal environment, and in zones of supergene jarosite alteration. At the McDermitt Hg deposit, Ga is enriched in the zone of alunite+kaolinite alteration below the zone of adularia-quartz alteration that coincides with the Hg ore body. The spatial relation of Ga enrichment to alunite-kaolinite alteration suggests that formation in a magmatic-hydrothermal environment. X-ray-absorption spectra of Ga-enriched samples from the McDermitt Hg deposit are similar to that of gallium sulfate and support the association of Ga enrichment with alunite alteration.

Infrared detection of the mineralogical aspects that influence the processing of calcined kaolin

NASA Astrophysics Data System (ADS)

Groenheide, Stefan; Guatame-Garcia, Adriana; Buxton, Mike; van der Werff, Harald

2017-04-01

Calcined kaolin is an industrial minerals product used in the production of paper, paint, rubber and other specialty applications. It is produced from kaolinite through a series of refinement steps and final calcination at temperatures of above 900°C, with the aim of generating a whiter and more abrasive material. The raw kaolin ore is a mixture of clay minerals, quartz and feldspars, where kaolinite is the main constituent. The optimal kaolin ores to feed the processing plant should ideally have high kaolinite abundance, be free in Fe-bearing mineralogy (to avoid influence in the colour of the product), and the kaolinite itself should be of high crystallinity (to ensure the correct abrasiveness after calcination). This work presents a case study from the kaolin deposits in the St. Austell Granite (South-West England), which are known for their high quality and world-class size. In this area, the kaolin is of primary-hydrothermal origin, with mineral associations that are related to the genetic history. The eventual depletion of the high-quality reserves is bringing now the attention to the lower grade zones, where the amount of impurities increases. As a consequence, it is critical to developing strategies that ensure the supply of high-quality ore to the processing plant. For this, it is necessary to acquire a thorough knowledge of the ore, including relative abundance of the minerals and their textural relationships. Hyperspectral images in the visible-near infrared (VNIR) and short-wave infrared (SWIR) ranges were collected from drill cores and run-off-mine (ROM) samples, obtained from one of the kaolin pits in the St. Austell area, where the kaolin quality is known to be lower than in the rest of the deposit. A series of mineral maps were generated to assess the distribution, texture and abundance of the Fe-bearing mineralogy and the other kaolin-associated minerals, as well as the variations in the crystallinity of kaolinite. The mineral maps enabled the

Differential Adsorption of Occluded and Nonoccluded Insect-Pathogenic Viruses to Soil-Forming Minerals

PubMed Central

Christian, Peter D.; Richards, Andrew R.; Williams, Trevor

2006-01-01

Soil represents the principal environmental reservoir of many insect-pathogenic viruses. We compared the adsorption and infectivity of one occluded and two nonoccluded viruses, Helicoverpa armigera single nucleopolyhedrovirus (HaSNPV) (Baculoviridae), Cricket paralysis virus (CrPV) (Dicistroviridae), and Invertebrate iridescent virus 6 (IIV-6) (Iridoviridae), respectively, in mixtures with a selection of soil-forming minerals. The relative infective titers of HaSNPV and CrPV were unchanged or slightly reduced in the presence of different minerals compared to their titers in the absence of the mineral. In contrast, the infective titer of IIV-6 varied according to the mineral being tested. In adsorption studies, over 98% of HaSNPV occlusion bodies were adsorbed by all the minerals, and a particularly high affinity was observed with ferric oxide, attapulgite, and kaolinite. In contrast, the adsorption of CrPV and IIV-6 differed markedly with mineral type, with low affinity to bentonites and high affinity to ferric oxide and kaolinite. We conclude that interactions between soil-forming minerals and insect viruses appear to be most important in nucleopolyhedroviruses, followed by invertebrate iridescent viruses, and least important in CrPV, which may reflect the ecology of these pathogens. Moreover, soils with a high content of iron oxides or kaolinite would likely represent highly effective reservoirs for insect-pathogenic viruses. PMID:16820456

Desorption and mobility mechanisms of co-existing polycyclic aromatic hydrocarbons and heavy metals in clays and clay minerals.

PubMed

Saeedi, Mohsen; Li, Loretta Y; Grace, John R

2018-05-15

The effects of soil components such as clay minerals and as humic acids, as well as co-existing metals and polycyclic aromatic hydrocarbons, on desorption and mobility are examined. Three types of artificially blended clay and clay mineral mixtures (pure kaolinite, kaolinite + sand and kaolinite + sand + bentonite), each with different humic acid content, were tested for desorption and mobility of acenaphthene, fluorene and fluoranthene by three extracting solutions CaCl 2 (0.01 M) and EDTA (0.01M) with non-ionic surfactants (Tween 80 and Triton X100). Heavy metals (Ni, Pb and Zn) were also studied for desorption and mobility. The influence of co-present metals on simultaneous desorption and mobility of PAHs was investigated as well. The results showed that <10% of metals in the clay mineral mixtures were mobile. Combined EDTA and non-ionic solutions can enhance the desorption and mobility of PAHs to >80% in clay mineral mixtures containing no sand, while in the same soils containing ∼40% sand, the desorption exceeded 90%. Heavy metals, as well as increasing humic acids content in the clay mineral mixtures, decreased the desorption and mobility of PAHs, especially for soils containing no sand, and for fluoranthene compared with fluorene and acenaphthene. Copyright © 2018 Elsevier Ltd. All rights reserved.

Electrokinetic Energy Conversion in Self-Assembled 2D Nanofluidic Channels with Janus Nanobuilding Blocks.

PubMed

Cheng, Hongfei; Zhou, Yi; Feng, Yaping; Geng, Wenxiao; Liu, Qinfu; Guo, Wei; Jiang, Lei

2017-06-01

Inspired by the microstructure of nacre, material design, and large-scale integration of artificial nanofluidic devices step into a completely new stage, termed 2D nanofluidics, in which mass and charge transportation are confined in the interstitial space between reconstructed 2D nanomaterials. However, all the existing 2D nanofluidic systems are reconstituted from homogeneous nanobuilding blocks. Herein, this paper reports the bottom-up construction of 2D nanofluidic materials with kaolinite-based Janus nanobuilding blocks, and demonstrates two types of electrokinetic energy conversion through the network of 2D nanochannels. Being different from previous 2D nanofluidic systems, two distinct types of sub-nanometer- and nanometer-wide fluidic channels of about 6.8 and 13.8 Å are identified in the reconstructed kaolinite membranes (RKM), showing prominent surface-governed ion transport behaviors and nearly perfect cation-selectivity. The RKMs exhibit superior capability in osmotic and hydraulic energy conversion, compared to graphene-based membranes. The mineral-based 2D nanofluidic system opens up a new avenue to self-assemble asymmetric 2D nanomaterials for energy, environmental, and healthcare applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Geochemistry and Minerality of Wine

NASA Astrophysics Data System (ADS)

Oze, C.; Horton, T. W.; Beaman, M.

2010-12-01

Kaolinite (Al2Si2O5(OH)4) and gibbsite (Al(OH)3) are capable of forming in a variety of environments including anthropogenic solutions such as wine. Here, we evaluate the geochemistry of twelve white wines in order to assess the potential relationship between kaolinite/gibbsite saturation and minerality, a common wine descriptor used to express the rock and/or soil character in the aromas and flavors of wines. Aluminum and Si concentrations ranged from 228-1,281 µg L-1 and 6,583-19,746 µg L-1, respectively, where Si and Al are the only elements to demonstrate positive covariance with minerality scores. Sulfur levels varied from 25,013-167,383 µg L-1 and show the strongest negative covariance with minerality scores. However, like all of the elements studied (Al, Si, Na, Mg, S, K, Ca, and Fe), these trends were not significantly different than random at the 95% confidence level. In contrast, the relative degrees of gibbsite/kaolinite saturation display strong positive covariance with minerality scores and these trends are not random at the greater than 95% confidence level. Overall, our tasters were able to accurately assess the degree of gibbsite/kaolinite saturation amongst the twelve wines based on the objective of assessing minerality. Although the wines were undersaturated with respect to gibbsite/kaolinite, geochemical modeling reveals that increasing the wines’ pHs from ~3.3 to 4.1-4.6 (which is achievable on the palate where saliva has a pH of 7.4) results in gibbsite/kaolinite oversaturation. By considering that minerality is a function of gibbsite/kaolinite saturation and decreasing S, the origin of minerality’s taste and chemical origin in wine with known physical standards becomes increasingly crystalline.

Importance of dust storms in the diagenesis of sandstones: a case study, Entrada sandstone in the Ghost Ranch area, New Mexico, USA

NASA Astrophysics Data System (ADS)

Orhan, Hükmü

1992-04-01

The importance of dust storms on geological processes has only been studied recently. Case-hardening, desert-varnish formation, duricrust development, reddening and cementation of sediments and caliche formation, are some important geological processes related to dust storms. Dust storms can also be a major source for cements in aeolian sandstones. The Jurassic aeolian Entrada Formation in the Ghost Ranch area is composed of quartz with minor amounts of feldspar and rock fragments, and is cemented with smectite as grain coatings and calcite and kaolinite as pore fillings. Smectite shows a crinkly and honeycomb-like morphology which points to an authigenic origin. The absence of smectite as framework grains and the presence of partially dissolved grains, coated with smectite and smectite egg-shells, indicate an external source. Clay and fine silt-size particles are believed to be the major source for cements, smectite and calcite in the Entrada Formation. The common association of kaolinite with altered feldspar, and the absence of kaolinite in spots heavily cemented with calcite, lead to the conclusions that the kaolinite formation postdates carbonates and that framework feldspar grains were the source of kaolinite.

Uptake properties of Ni2+ by nCaO.Al2O3.2SiO2 (n=1-4) prepared from solid-state reaction of kaolinite and calcite.

PubMed

Jha, Vinay Kumar; Kameshima, Yoshikazu; Nakajima, Akira; Okada, Kiyoshi; MacKenzie, Kenneth J D

2005-08-31

A series of nCaO.Al2O3.2SiO2 samples (n=1-4) were prepared by solid-state reaction of mechanochemically treated mixtures of kaolinite and calcite fired at 600-1000 degrees C for 24 h. All the samples were X-ray amorphous after firing at 600-800 degrees C but had crystallized by 900 degrees C. The main crystalline phases were anorthite (n=1), gehlenite (n=2 and 3) and larnite (n=4). The uptake of Ni2+ by nCaO.Al2O3.2SiO2 samples fired at 800 and 900 degrees C was investigated at room temperature using solutions with initial Ni2+ concentrations of 0.1-50 mmol/l. Amorphous samples (fired at 800 degrees C) showed a higher Ni2+ uptake capacity than crystalline samples (fired at 900 degrees C). Ni2+ uptake was found to increase with increasing of CaO content. Amorphous 4CaO.Al2O3.2SiO2 showed the highest Ni2+ uptake capacity (about 9 mmol/g). The Ni2+ uptake abilities of the present samples are higher than those of other materials reported in the literature. Since the sorbed Ni2+/released Ca2+ ratios of these samples are close to unity, ion replacement of Ni2+ for Ca2+ is thought to be the principal mechanism of Ni2+ uptake by the present samples.

Revised values for the Gibbs free energy of formation of [Al(OH)4 aq-], diaspore, boehmite and bayerite at 298.15 K and 1 bar, the thermodynamic properties of kaolinite to 800 K and 1 bar, and the heats of solution of several gibbsite samples

USGS Publications Warehouse

Hemingway, B.S.; Robie, R.A.; Kittrick, J.A.

1978-01-01

Solution calorimetric measurements compared with solubility determinations from the literature for the same samples of gibbsite have provided a direct thermochemical cycle through which the Gibbs free energy of formation of [Al(OH)4 aq-] can be determined. The Gibbs free energy of formation of [Al(OH)4 aq-] at 298.15 K is -1305 ?? 1 kJ/mol. These heat-of-solution results show no significant difference in the thermodynamic properties of gibbsite particles in the range from 50 to 0.05 ??m. The Gibbs free energies of formation at 298.15 K and 1 bar pressure of diaspore, boehmite and bayerite are -9210 ?? 5.0, -918.4 ?? 2.1 and -1153 ?? 2 kJ/mol based upon the Gibbs free energy of [A1(OH)4 aq-] calculated in this paper and the acceptance of -1582.2 ?? 1.3 and -1154.9 ?? 1.2 kJ/mol for the Gibbs free energy of formation of corundum and gibbsite, respectively. Values for the Gibbs free energy formation of [Al(OH)2 aq+] and [AlO2 aq-] were also calculated as -914.2 ?? 2.1 and -830.9 ?? 2.1 kJ/mol, respectively. The use of [AlC2 aq-] as a chemical species is discouraged. A revised Gibbs free energy of formation for [H4SiO4aq0] was recalculated from calorimetric data yielding a value of -1307.5 ?? 1.7 kJ/mol which is in good agreement with the results obtained from several solubility studies. Smoothed values for the thermodynamic functions CP0, ( HT0 - H2980) T, ( GT0 - H2980) T, ST0 - S00, ??Hf{hook},2980 kaolinite are listed at integral temperatures between 298.15 and 800 K. The heat capacity of kaolinite at temperatures between 250 and 800 K may be calculated from the following equation: CP0 = 1430.26 - 0.78850 T + 3.0340 ?? 10-4 T2 -1.85158 ?? 10-4 T2 1 2 + 8.3341 ?? 106 T-2. The thermodynamic properties of most of the geologically important Al-bearing phases have been referenced to the same reference state for Al, namely gibbsite. ?? 1978.

Mineralogy and source rock evaluation of the marine Oligo-Miocene sediments in some wells in the Nile Delta and North Sinai, Egypt

NASA Astrophysics Data System (ADS)

El sheikh, Hassan; Faris, Mahmoud; Shaker, Fatma; Kumral, Mustafa

2016-06-01

This paper aims to study the mineralogical composition and determine the petroleum potential of source rocks of the Oligocene-Miocene sequence in the Nile Delta and North Sinai districts. The studied interval in the five wells can be divided into five rock units arranged from the top to base; Qawasim, Sidi Salem, Kareem, Rudeis, and Qantara formations. The bulk rock mineralogy of the samples was investigated using X-Ray Diffraction technique (XRD). The results showed that the sediments of the Nile Delta area are characterized by the abundance of quartz and kaolinite with subordinate amounts of feldspars, calcite, gypsum, dolomite, and muscovite. On the other hand, the data of the bulk rock analysis at the North Sinai wells showed that kaolinite, quartz, feldspar and calcite are the main constituents associated with minor amounts of dolomite, gypsum, mica, zeolite, and ankerite. Based on the organic geochemical investigations (TOC and Rock-Eval pyrolysis analyses), all studied formations in both areas are thermally immature but in the Nile delta area, Qawasim, Sidi Salem and Qantara formations (El-Temsah-2 Well) are organically-rich and have a good petroleum potential (kerogen Type II-oil-prone), while Rudeis Formation is a poor petroleum potential source rock (kerogen Type III-gas-prone). In the North Sinai area, Qantara Formation has a poor petroleum potential (kerogen Type III-gas-prone) and Sidi Salem Formation (Bardawil-1 Well) is a good petroleum potential source rock (kerogen Type II-oil-prone).

Mineralogy and thermal properties of clay from Slatina (Ub, Serbia)

NASA Astrophysics Data System (ADS)

Milosevic, Maja; Logar, Mihovil; Kaludjerovic, Lazar; Jelic, Ivana

2017-04-01

The "Slatina" deposit, Ub, Serbia was opened in 1965 and represents one of few deposits exploited by "Kopovi" a.d., Ub, company. Deposit is composed of clay layers belonging to Neogene sediments that are widespread transgressive over granitoid rocks of Cer mountain and Paleozoic and Mesozoic sediments. Clay is mostly of illite-montmorillonite-kaolinite type and they are generally used as ceramic materials while some of the layers are used as fire-resistant materials. In this study we present mineralogical and thermal characterization of two samples to determine their application as industrial materials. Chemical and mineral composition was determined using inductively coupled plasma optical emission spectroscopy (ICP-OES), X-ray diffraction (XRD) on powder and oriented samples, infrared spectroscopy (IR) and granulometry. Cationic exchange capacity (CEC) and specific surface area (SSA) was determined using spectrophotometry and methylene blue (MB). Thermal properties where determined by gravimetry (120, 350, 600 and 1000 oC) and differential thermal analysis (DTA). Quantitative mineral composition obtained by Rietveld refinement of combined chemical and XRD data shows that the sample 1(SC) is mainly smectite-illite (45%) and kaolinite (14%) clay with 19% of quartz, 10% feldspars and 7% of limonite, while sample 2(SV) is smectite-illite (43%) and kaolinite (11%) clay with 10% of quartz, 15% feldspars and 7% of limonite. Both samples have low content of impurities (carbonate minerals). Medium grain size (μm) goes from 1.02 (SSA = 104 m2/g) for sample 1(SC) to 0.71 (SSA = 117 m2/g) for sample 2(SV) while their CEC is 12.7 and 14.9 mmol/100g for 1(SC) and 2(SV) respectively. IR spectra of the samples shows larger amount of smectite clays with quartz and carbonate minerals for both samples which is in accordance with XRD data. DTA data shows couple of events that are endothermic. First one (100-200 oC) is associated with loss of moisture and constitutive water, second

Colour and toxic characteristics of metakaolinite–hematite pigment for integrally coloured concrete, prepared from iron oxide recovered from a water treatment plant of an abandoned coal mine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sadasivam, Sivachidambaram, E-mail: sadasivams@cardiff.ac.uk; Thomas, Hywel Rhys

A metakaolinite-hematite (KH) red pigment was prepared using an ocherous iron oxide sludge recovered from a water treatment plant of an abandoned coal mine. The KH pigment was prepared by heating the kaolinite and the iron oxide sludge at kaolinite's dehydroxylation temperature. Both the raw sludge and the KH specimen were characterised for their colour properties and toxic characteristics. The KH specimen could serve as a pigment for integrally coloured concrete and offers a potential use for the large volumes of the iron oxide sludge collected from mine water treatment plants. - Graphical abstract: A kaolinite based red pigment wasmore » prepared using an ocherous iron oxide sludge recovered from an abandoned coal mine water treatment plant. Display Omitted - Highlights: • A red pigment was prepared by heating a kaolinite and an iron oxide sludge. • The iron oxide and the pigment were characterised for their colour properties. • The red pigment can be a potential element for integrally coloured concrete.« less

The Western North American Cretaceous-Tertiary (K-T) boundary interval and its content of shock-metamorphosed minerals: Implications concerning the K-T boundary impact-extinction theory

NASA Technical Reports Server (NTRS)

Izett, G. A.

1988-01-01

At 20 sites in the Raton Basin of Colorado and New Mexico, and at several other sites in Wyoming, Montana, and Canada, a pair of claystone units, an Ir abundance anomaly, and a concentration of shock-metamorphosed minerals mark the palynological K-T boundary. The K-T boundary claystone, which is composed of kaolinite and small amounts of illite/smectite mixed-layer clay, is similar in most respects to kaolinite tonstein layers in coal beds. At some, but not all, K-T boundary localities, the boundary claystone contains solid kaolinite and hollow and solid goyazite spherules, 0.05 to 1.2 mm in diameter. The upper unit, the K-T boundary impact layer, consists chiefly of kaolinite and various amounts of illite/smectite mixed-layer clay. The impact layer and boundary claystone are similar chemically, except that the former has slightly more Fe, K, Ba, Cr, Cu, Li, V, and Zn than the latter. The facts that the boundary claystone and impact layer contain anomalous amounts of Ir, comprise a stratigraphic couplet at Western North American sites, and form thin, discrete layers, similar to air-fall units (volcanic or impact), suggest that the claystone units are of impact origin. Significantly, the impact layer contains as much as 2 percent clastic mineral grains, about 30 percent of which contain multiple sets of shock lamellae. Only one such concentration of shocked minerals has been found near the K-T boundary. The type of K-T boundary shock-metamorphosed materials (quartzite and metaquartzite) in the impact layer and the lack of shock lamellae in quartz and feldspar of pumice lapilli and granitic xenoliths in air-fall pumice units of silicic tuffs, such as the Bishop Tuff, eliminate the possibility that the shock-metamorphosed minerals in the K-T impact layer are of volcanic origin. The global size distribution and abundance of shock-metamorphosed mineral grains suggest that the K-T impact occurred in North America.

Selected elements in major minerals from bituminous coal as determined by INAA: Implications for removing environmentally sensitive elements from coal

USGS Publications Warehouse

Palmer, C.A.; Lyons, P.C.

1996-01-01

The four most abundant minerals generally found in Euramerican bituminous coals are quartz, kaolinite, illite and pyrite. These four minerals were isolated by density separation and handpicking from bituminous coal samples collected in the Ruhr Basin, Germany and the Appalachian basin, U.S.A. Trace-element concentrations of relatively pure (??? 99+%) separates of major minerals from these coals were determined directly by using instrumental neutron activation analysis (INAA). As expected, quartz contributes little to the trace-element mass balance. Illite generally has higher trace-element concentrations than kaolinite, but, for the concentrates analyzed in this study, Hf, Ta, W, Th and U are in lower concentrations in illite than in kaolinite. Pyrite has higher concentrations of chalcophile elements (e.g., As and Se) and is considerably lower in lithophile elements as compared to kaolinite and illite. Our study provides a direct and sensitive method of determining trace-element relationships with minerals in coal. Mass-balance calculations suggest that the trace-element content of coal can be explained mainly by three major minerals: pyrite, kaolinite and illite. This conclusion indicates that the size and textural relationships of these major coal minerals may be a more important consideration as to whether coal cleaning can effectively remove the most environmentally sensitive trace elements in coal than what trace minerals are present.

Exploration of gold occurrences in alteration zones at Dungash district, Southeastern Desert of Egypt using ASTER data and geochemical analyses

NASA Astrophysics Data System (ADS)

Salem, S. M.; El Sharkawi, M.; El-Alfy, Z.; Soliman, N. M.; Ahmed, S. E.

2016-05-01

The present study aims at exploration of new gold occurrences in the alteration zones at Dungash district. Processed ASTER images band ratios 7/6 × 4/6 and (7 + 9/8), field geology and mineralogical and geochemical data help characterize three types of alterations in three areas 1 to 3 that may be targeted for Au exploration. Area1 confined to the metavolcanics located in the SE of Dungash gold mine and revealed silicified and sericitized type alterations, composed of quartz, epidote, chlorite, biotite and opaque minerals mainly pyrite and chalcopyrite. Area2 occurs in the gabbro-diorite rocks at Abu Meraiwa area NE of Dungash gold mine, which are rich in kaolinite, illite, sericite, pyrite, arsenopyrite and chalcopyrite that record kaolinitized alteration. Area3 is hosted in carbonaceous listwaenized serpentinite thus indicating the role of listwaenitization type alteration in ore genesis. It is composed of calcite, chromite, pyrite, arsenopyrite, chalcopyrite and Ni-bearing sulphides. Au contents in area 1 range between 0.12 and 14.91 ppm, and between 6.1 and 16.3 ppm in area 2, while gold values in area 3 vary from <0.01 to 0.03 ppm. Dungash district is comprised of Pan-African assemblages of ophiolitic ultramafics thrusted over the island arc metavolcanics of dacitic- andesite composition. Gabbro-diorite rocks are intruded in the ultramafics and the acidic metavolcanics as well as diorite-quartz diorite suite intruded in the intermediate metavolcanics. Several acidic dykes, granitic dykes and quartz veins cut through the different rocks types.

Clay minerals behaviour in thin sandy clay-rich lacustrine turbidites (Lake Hazar, Turkey)

NASA Astrophysics Data System (ADS)

El Ouahabi, Meriam; Hubert-Ferrari, Aurelia; Lamair, Laura; Hage, Sophie

2017-04-01

Turbidites have been extensively studied in many different areas using cores or outcrop, which represent only an integrated snapshot of a dynamic evolving flow. Laboratory experiments provide the missing relationships between the flow characteristics and their deposits. In particular, flume experiments emphasize that the presence of clay plays a key role in turbidity current dynamics. Clay fraction, in small amount, provides cohesive strength to sediment mixtures and can damp turbulence. However, the degree of flocculation is dependent on factors such as the amount and size of clay particles, the surface of clay particles, chemistry and pH conditions in which the clay particles are dispersed. The present study focuses on thin clayey sand turbidites found in Lake Hazar (Turkey) occurring in stacked thin beds. Depositional processes and sources have been previously studied and three types were deciphered, including laminar flows dominated by cohesion, transitional, and turbulence flow regimes (Hage et al., in revision). For the purpose of determine the clay behavior in the three flow regimes, clay mineralogical, geochemical measurements on the cores allow characterising the turbidites. SEM observations provide further information regarding the morphology of clay minerals and other clasts. The study is particularly relevant given the highly alkaline and saline water of the Hazar Lake. Clay minerals in Hazar Lake sediments include kaolinite (1:1-type), illite and chlorite (2:1-type). Hazar lake water is alkaline having pH around 9.3, in such alkaline environment, a cation-exchange reaction takes place. Furthermore, in saline water (16‰), salts can act as a shield and decrease the repulsive forces between clay particle surfaces. So, pH and salt content jointly impact the behaviour of clays differently. Since the Al-faces of clay structures have a negative charge in basic solutions. At high pH, all kaolinite surfaces become negative-charged, and then kaolinite

Evidence of phyllosilicates in Wooly Patch, an altered rock encountered at West Spur, Columbia Hills, by the Spirit rover in Gusev crater, Mars

USGS Publications Warehouse

Wang, A.; Korotev, R.L.; Jolliff, B.L.; Haskin, L.A.; Crumpler, L.; Farrand, W. H.; Herkenhoff, K. E.; de Souza, Jr.; Kusack, A.G.; Hurowitz, J.A.; Tosca, N.J.

2006-01-01

On its traverse to Columbia Hills, the Mars Exploration Rover Spirit investigated an outcrop designated "Wooly Patch" that exhibited morphological, mineralogical, and geochemical characteristics at the extreme ends of ranges observed among rocks studied at West Spur, a westward projecting salient near the foot of the Columbia Hills, Gusev crater. The major-element composition and Fe-mineralogy, as determined by the Alpha-Particle X-ray Spectrometer and Mo??ssbauer Spectrometer, are inconsistent with any reasonable assemblage of basaltic minerals in that there is an excess of Si and Al. The combined data are best explained by the presence of 14-17% phyllosilicate minerals. Phyllosilicates that account for the composition and cation ratios include members of the kaolinite, serpentine, chlorite, and septechlorite groups. The potential existence of kaolinite-type Al-rich phyllosilicates within the Wooly Patch outcrop suggests a mildly acidic environment (pH 4-6) in the past and an open hydrologic system with good drainage conditions in the environment where these rocks were altered. Copyright 2006 by the American Geophysical Union.

Mineralogy and thermal properties of kaolin from the San José (Oruro, Bolivia)

NASA Astrophysics Data System (ADS)

Alfonso, Pura; Garcia-Valles, Maite; Martínez, Salvador; Amando Penedo, Lucio; Elvys Trujillo, Juan

2016-04-01

The San José mine, Oruro, Bolivia is known for provided a broad diversity of minerals. The San José Sn deposit is a Sn-Ag deposit composed of veins hosted in a complex of Miocene domes from monzonitic to dioritic composition within rhyolitic volcanic rocks hosted in Tertiary sedimentary rocks. Advanced argillitic alteration. is widespread in the surroundings of the deposit. Kaolinitization reach industrial importance and the kaolinitized rock is exploited, however it was not already been characterised. In this study we present a preliminary mineralogical and thermal characterization to determine the industrial applications of these kaolinitic materials. A sampling of the kaolinitized rocks in outcrops from the mining area was undertaken. The chemical composition of major and trace elements was determined by X-ray fluorescence (XRF). Mineralogy was obtained by powder diffraction X-ray (XRD) and infrared spectroscopy (FTIR). Quantitative determination of phases was obtained by the Rietveld refinement method using the Fullprof software. Thermal properties were determined by differential thermal analysis-thermo gravimetry (DTA -TG) and dilatometry. Mineral phases determined are mainly quartz (54-55 wt. %), kaolinite (7-8 wt. %), K-feldspar (8-19 wt. %), muscovite (16-17 wt. %), plagioclase up to 3 wt. %, alunite up to 8 wt% and gypsum up to 4 wt%. DTA -TG show a first endothermic event related to the dehydration of gypsum, with a loss weight of 0.4 wt%. An endothermic peak corresponding to the loss of the OH- groups of kaolinite occurs about 520 °C and an exothermic, at 980 °C, due to the crystallization of the mullite phase. The endothermic peak is attributed to the transformation of kaolinite in metakaolinite: Al2Si2O5 (OH)4  Al2Si2O7 + 2H2O and the dehydroxilation of alunite; the loss weight associated with this event is 2.9-3.2 wt%. The exothermic peak is caused by the formation of mullite: 3Al2Si2O7  Al6Si2O13 + 4SiO2. Another loss weight, of 3wt%, is

Adsorption of reovirus to clay minerals: effects of cation-exchange capacity, cation saturation, and surface area.

PubMed Central

Lipson, S M; Stotzky, G

1983-01-01

The adsorption of reovirus to clay minerals has been reported by several investigators, but the mechanisms defining this association have been studied only minimally. The purpose of this investigation was to elucidate the mechanisms involved with this interaction. More reovirus type 3 was adsorbed, in both distilled and synthetic estuarine water, by low concentrations of montmorillonite than by comparable concentrations of kaolinite containing a mixed complement of cations on the exchange complex. Adsorption to the clays was essentially immediate and was correlated with the cation-exchange capacity of the clays, indicating that adsorption was primarily to negatively charged sites on the clays. Adsorption was greater with low concentrations of clays in estuarine water than in distilled water, as the higher ionic strength of the estuarine water reduced the electrokinetic potential of both clay and virus particles. The addition of cations (as chloride salts) to distilled water enhanced adsorption, with divalent cations being more effective than monovalent cations and 10(-2) M resulting in more adsorption than 10(-3) M. Potassium ions suppressed reovirus adsorption to montmorillonite, probably by collapsing the clay lattices and preventing the expression of the interlayer-derived cation-exchange capacity. More virus was adsorbed by montmorillonite made homoionic to various mono-, di-, and trivalent cations (except by montmorillonite homoionic to potassium) than by comparable concentrations of kaolinite homoionic to the same cations. The sequence of the amount of adsorption to homoionic montmorillonite was Al greater than Ca greater than Mg greater than Na greater than K; the sequence of adsorption to kaolinite was Na greater than Al greater than Ca greater than Mg greater than K. The constant partition-type adsorption isotherms obtained when the clay concentration was maintained constant and the virus concentration was varied indicated that a fixed proportion of the

Insights into structural and dynamical features of water at halloysite interfaces probed by DFT and classical molecular dynamics simulations.

PubMed

Presti, Davide; Pedone, Alfonso; Mancini, Giordano; Duce, Celia; Tiné, Maria Rosaria; Barone, Vincenzo

2016-01-21

Density functional theory calculations and classical molecular dynamics simulations have been used to investigate the structure and dynamics of water molecules on kaolinite surfaces and confined in the interlayer of a halloysite model of nanometric dimension. The first technique allowed us to accurately describe the structure of the tetrahedral-octahedral slab of kaolinite in vacuum and in interaction with water molecules and to assess the performance of two widely employed empirical force fields to model water/clay interfaces. Classical molecular dynamics simulations were used to study the hydrogen bond network structure and dynamics of water adsorbed on kaolinite surfaces and confined in the halloysite interlayer. The results are in nice agreement with the few experimental data available in the literature, showing a pronounced ordering and reduced mobility of water molecules at the hydrophilic octahedral surfaces of kaolinite and confined in the halloysite interlayer, with respect to water interacting with the hydrophobic tetrahedral surfaces and in the bulk. Finally, this investigation provides new atomistic insights into the structural and dynamical properties of water-clay interfaces, which are of fundamental importance for both natural processes and industrial applications.

Enhancement of Plant Establishment on Dredged Material Sites with Mycorrhizal Fungi and Clay Amendments

DTIC Science & Technology

1989-10-01

montmorillonite enhanced the growth of smooth brome grass. Topsoil, the clays attapulgite and kaolinite , and the commercial products Agrosoke anj Stawetwere...clays bentonite, attapulgite, kaolinite , and montmorillonite . Trade name and company addresses for the clays are listed in Table 1. Agrosoke and Stawet...desertcoZa, G. etunicatwn, and G. intraradice8. The clays attapulgite, ben- tonite, kaclinite,/and montmorillonite from various commercial sources were

Immersion freezing of supermicron mineral dust particles: freezing results, testing different schemes for describing ice nucleation, and ice nucleation active site densities.

PubMed

Wheeler, M J; Mason, R H; Steunenberg, K; Wagstaff, M; Chou, C; Bertram, A K

2015-05-14

Ice nucleation on mineral dust particles is known to be an important process in the atmosphere. To accurately implement ice nucleation on mineral dust particles in atmospheric simulations, a suitable theory or scheme is desirable to describe laboratory freezing data in atmospheric models. In the following, we investigated ice nucleation by supermicron mineral dust particles [kaolinite and Arizona Test Dust (ATD)] in the immersion mode. The median freezing temperature for ATD was measured to be approximately -30 °C compared with approximately -36 °C for kaolinite. The freezing results were then used to test four different schemes previously used to describe ice nucleation in atmospheric models. In terms of ability to fit the data (quantified by calculating the reduced chi-squared values), the following order was found for ATD (from best to worst): active site, pdf-α, deterministic, single-α. For kaolinite, the following order was found (from best to worst): active site, deterministic, pdf-α, single-α. The variation in the predicted median freezing temperature per decade change in the cooling rate for each of the schemes was also compared with experimental results from other studies. The deterministic model predicts the median freezing temperature to be independent of cooling rate, while experimental results show a weak dependence on cooling rate. The single-α, pdf-α, and active site schemes all agree with the experimental results within roughly a factor of 2. On the basis of our results and previous results where different schemes were tested, the active site scheme is recommended for describing the freezing of ATD and kaolinite particles. We also used our ice nucleation results to determine the ice nucleation active site (INAS) density for the supermicron dust particles tested. Using the data, we show that the INAS densities of supermicron kaolinite and ATD particles studied here are smaller than the INAS densities of submicron kaolinite and ATD particles

Immersion freezing in concentrated solution droplets for a variety of ice nucleating particles

NASA Astrophysics Data System (ADS)

Wex, Heike; Kohn, Monika; Grawe, Sarah; Hartmann, Susan; Hellner, Lisa; Herenz, Paul; Welti, Andre; Lohmann, Ulrike; Kanji, Zamin; Stratmann, Frank

2016-04-01

The measurement campaign LINC (Leipzig Ice Nucleation counter Comparison) was conducted in September 2015, during which ice nucleation measurements as obtained with the following instruments were compared: - LACIS (Leipzig Aerosol Cloud Interaction Simulator, see e.g. Wex et al., 2014) - PIMCA-PINC (Portable Immersion Mode Cooling Chamber together with PINC) - PINC (Portable Ice Nucleation Chamber, Chou et al., 2011) - SPIN (SPectrometer for Ice Nuclei, Droplet Measurement Technologies) While LACIS and PIMCA-PINC measured immersion freezing, PINC and SPIN varied the super-saturation during the measurements and collected data also for relative humidities below 100% RHw. A suite of different types of ice nucleating particles were examined, where particles were generated from suspensions, subsequently dried and size selected. For the following samples, data for all four instruments are available: K-feldspar, K-feldspar treated with nitric acid, Fluka-kaolinite and birch pollen. Immersion freezing measurements by LACIS and PIMCA-PINC were in excellent agreement. Respective parameterizations from these measurement were used to model the ice nucleation behavior below water vapor saturation, assuming that the process can be described as immersion freezing in concentrated solutions. This is equivalent to simply including a concentration dependent freezing point depression in the immersion freezing parameterization, as introduced for coated kaolinite particles in Wex et al. (2014). Overall, measurements performed below water vapor saturation were reproduced by the model, and it will be discussed in detail, why deviations were observed in some cases. Acknowledgement: Part of this work was funded by the DFG Research Unit FOR 1525 INUIT, grant WE 4722/1-2. Literature: Chou, C., O. Stetzer, E. Weingartner, Z. Juranyi, Z. A. Kanji, and U. Lohmann (2011), Ice nuclei properties within a Saharan dust event at the Jungfraujoch in the Swiss Alps, Atmos. Chem. Phys., 11(10), 4725

Chemistry, mineralogy and alteration intensity of hydrothermal altered Mt Unzen conduit rocks (Shimabara/Japan)

NASA Astrophysics Data System (ADS)

Hess, Kai-Uwe; Yilmaz, Tim; Gilg, H. Albert; Janots, Emilie; Mayer, Klaus; Nakada, Setsuya; Dingwell, Donald

2017-04-01

Investigations were carried out on hydrothermally altered coherent dacitic dykes samples from (USDP-4) drill core at Mt Unzen stratovolcano (Shimabara/Japan). XRF, XRD, EMPA, C-O-isotope, hot-cathode CL and SEM analysis led to insights concerning chemistry, mineralogy, and intensity and type of alteration as well as the origin of carbonate-precipitating fluids. Additionally a textural characterization of the occurring replacement features in the volcanic conduit rocks was performed. The occurrence of the main secondary phases such as chlorite, pyrite, carbonates, and R1 (Reichweite parameter) illite-smectite and kaolinite group minerals indicate a weak to moderate propylitic to phyllic hydrothermal alteration. The dacitic samples of the dykes show different hydrothermal alteration features: (i) carbonate and chlorite pseudomorphs after hornblende as well as core and zonal textures due to replacement of plagioclase by R1 illite-smectite as well as kaolinite group minerals, (ii) colloform banded fracture fillings and fillings in dissolution vugs, and (iii) chlorite, R1 illite-smectite as well as kaolinite group minerals in the groundmass. Late chlorite veins crosscut precipitates of R1 illite-smectite as well as kaolinite group minerals. Carbonates in fractures and in pseudomorphs after hornblende comprise iron-rich dolomite solid solutions ("ankerite") and calcite. Isotopic values indicate a hydrothermal-magmatic origin for the carbonate formation. The chlorite-carbonate-pyrite index (CCPI) and the Ishikawa alteration index (AI), applied to the investigated samples show significant differences (CCPI=52.7-57.8; AI=36.1-40.6) indicating their different degree of alteration. According to Nakada et al., 2005, the C13 to C16 dykes represent the feeder dyke from the latest eruption (1991-1995) whereas C8 represents an earlier dyke feeder dyke from an older eruption. Weakest alteration, which was obtained in samples C16-1-5 and C13-2-5, correlates with the alteration

A review of the surface features and properties, surfactant adsorption and floatability of four key minerals of diasporic bauxite resources.

PubMed

Zhang, Ningning; Nguyen, Anh V; Zhou, Changchun

2018-04-01

Diasporic bauxite represents one of the major aluminum resources. Its upgrading for further processing involves a separation of diaspore (the valuable mineral) from aluminosilicates (the gangue minerals) such as kaolinite, illite, and pyrophyllite. Flotation is one of the most effective ways to realize the upgrading. Since flotation is a physicochemical process based on the difference in the surface hydrophobicity of different components, determining the adsorption characteristics of various flotation surfactants on the mineral surfaces is critical. The surfactant adsorption properties of the minerals, in turn, are controlled by the surface chemistry of the minerals, while the latter is related to the mineral crystal structures. In this paper, we first discuss the crystal structures of the four key minerals of diaspore, kaolinite, illite, and pyrophyllite as well as the broken bonds on their exposed surfaces after grinding. Next, we summarize the surface chemistry properties such as surface wettability and surface electrical properties of the four minerals, and the differences in these properties are explained from the perspective of mineral crystal structures. Then we review the adsorption mechanism and adsorption characteristics of surfactants such as collectors (cationic, anionic, and mixed surfactants), depressants (inorganic and organic), dispersants, and flocculants on these mineral surfaces. The separation of diaspore and aluminosilicates by direct flotation and reverse flotation are reviewed, and the collecting properties of different types of collectors are compared. Furthermore, the abnormal behavior of the cationic flotation of kaolinite is also explained in this section. This review provides a strong theoretical support for the optimization of the upgrading of diaspore bauxite ore by flotation and the early industrialization of the reverse flotation process. Copyright © 2018 Elsevier B.V. All rights reserved.

Infrared Spectroscopic Study on Structural Change and Interfacial Interaction in Rubber Composites Filled with Silica-Kaolin Hybrid Fillers

NASA Astrophysics Data System (ADS)

Chen, Y.; Guan, J.; Hu, H.; Gao, H.; Zhang, L.

2016-07-01

A series of natural rubber/styrene butadiene rubber/polybutadiene rubber composites was prepared with nanometer silica and micron kaolin by a dry modification process, mechanical compounding, and mold vulcanization. Fourier transform infrared spectroscopy and a scanning electron microscope were used to investigate the structural changes and interfacial interactions in composites. The results showed that the "seesaw" structure was formed particularly with the incorporation of silica particles in the preparation process, which would be beneficial to the dispersibility of fillers in the rubber matrix. The kaolinite platelets were generally arranged in directional alignment. Kaolinite with smaller particle size and low-defect structure was more stable in preparation, but kaolinite with larger particle size and high defect structure tended to change the crystal structure. The composite prepared in this research exhibited excellent mechanical and thermal properties.

Soil physicochemical properties to evaluate soil degradation under different land use types in a high rainfall tropical region: A case study from South Sulawesi, Indonesia

NASA Astrophysics Data System (ADS)

Ahmad, A.; Lopulisa, C.; Imran, A. M.; Baja, S.

2018-05-01

Intensive cropping in the tropical region always becomes one of important driving forces of soil degradation. The primary aim of this study is to analyze the states and the dynamics of soil physicochemical properties to evaluate soil degradation in the tropical region a high rainfall on agricultural areas in South Sulawesi. A number of soil characteristics were analyzed for physical and chemical properties, and clay minerals with X-ray diffractometer. The degree of soil degradation is determined using Wischmeier and Smith equation. This study reveals that mean annual precipitation in 1979-2016 ranged from 1853.15 to 2981.30 mm/year. For land used for paddy field, palm oil, cacao and coffee plantation, the texture dominated with silt loam-clay loam, cation exchange capacity was 18.63-26.32 cmol+ kg-1, 0.98-2.91% of C-organic, 32-55% of base saturation, 0.1-3.5 cm h-1 of permeability, soil clay minerals were montmorillonite-kaolinite-halloysite, and the index erodibility was 0.3-0.5. Land used for mixed plants and shrubs, the texture dominated with silt loam-sandy clay loam, cation exchange capacity was 18.63-27.12 cmol+ kg-1, 1.09-2.89% of C-organic, 32-55% of base saturation, 0.2-4.9 cm/h of permeability, soil clay minerals were kaolinite-halloysite, and index erodibility was 0.1-0.3. Land use for cultivated in the high intensity of rainfall has changed the physicochemical properties of soils, but cultivated in monoculture has at some degree increased soil erodibility.

Copper sludge from printed circuit board production/recycling for ceramic materials: a quantitative analysis of copper transformation and immobilization.

PubMed

Tang, Yuanyuan; Lee, Po-Heng; Shih, Kaimin

2013-08-06

The fast development of electronic industries and stringent requirement of recycling waste electronics have produced a large amount of metal-containing waste sludge. This study developed a waste-to-resource strategy to beneficially use such metal-containing sludge from the production and recycling processes of printed circuit board (PCBs). To observe the metal incorporation mechanisms and phase transformation processes, mixtures of copper industrial waste sludge and kaolinite-based materials (kaolinite and mullite) were fired between 650 and 1250 °C for 3 h. The different copper-hosting phases were identified by powder X-ray diffraction (XRD) in the sintered products, and CuAl2O4 was found to be the predominant hosting phase throughout the reactions, regardless of the strong reduction potential of copper expected at high temperatures. The experimental results indicated that CuAl2O4 was generated more easily and in larger quantities at low-temperature processing when using the kaolinite precursor. Maximum copper transformations reached 86% and 97% for kaolinite and mullite systems, respectively, when sintering at 1000 °C. To monitor the stabilization effect after thermal process, prolonged leaching tests were carried out using acetic acid with an initial pH value of 2.9 to leach the sintered products for 20 days. The results demonstrated the decrease of copper leachability with the formation of CuAl2O4, despite different sintering behavior in kaolinite and mullite systems. This study clearly indicates spinel formation as the most crucial metal stabilization mechanism when sintering copper sludge with aluminosilicate materials, and suggests a promising and reliable technique for reusing metal-containing sludge as ceramic materials.

Phyllosilicate weathering pathways in chlorite-talc bearing soil parent materials, D.R. Congo: early findings.

NASA Astrophysics Data System (ADS)

Dumon, Mathijs; Oostermeyer, Fran; Timmermans, Els; De Meulemeester, Aschwin; Mees, Florias; Van Driessche, Isabel; Erens, Hans; Bazirake Mujinya, Basile; Van Ranst, Eric

2015-04-01

The study of the formation and transformation of clay minerals is of the upmost importance to understand soil formation and to adjust land-use management to the land surface conditions. These clay minerals determine to a large extent the soil physical and chemical properties. It is commonly observed that over time the mineralogy of any parent material is transformed to a simple assemblage composed mostly of Al and Fe oxides and low-activity clays, e.g. kaolinite. This is especially obvious in the humid tropics, which have been protected from glacial erosion, allowing deep, highly weathered soils to form. Despite the abundant presence of kaolinite in these soils, its formation pathways are still under debate: either neoformation by dissolution-crystallisation reactions or solid-state transformation of 2:1 phyllosilicates. To elucidate this, weathering sequences in a unique 40 m core taken below a termite mound, reaching a talc-chlorite bearing substrate in the Lubumbashi area, Katanga, DR Congo are being investigated in detail using a.o. quantitative X-ray diffraction analysis, chemical characterization, micromorphology and µXRF-scanning with the main objective to improve the understanding of the formation pathways of kaolinite subgroup minerals in humid tropical environments. Based on an initial characterization of the core, two zones of interest were selected for more detailed analysis, for which the early findings will be presented. The first zone extends from ca. 9 m to 11 m below the surface is dominated by kaolinite but shows early traces of primary talc and micas. The second zone extends from 34 to 36 m below the surface and contains large amounts of chlorite, with smaller amounts of talc, micas and kaolinite.

Photodegradation of decabromodiphenyl ether adsorbed onto clay minerals, metal oxides, and sediment.

PubMed

Ahn, Mi-Youn; Filley, Timothy R; Jafvert, Chad T; Nies, Loring; Hua, Inez; Bezares-Cruz, Juan

2006-01-01

The photodebromination of decabromodiphenyl ether (BDE-209) adsorbed onto six different solid matrixes was investigated in sunlight and by irradiation with 350 +/- 50 nm lamps (four lamps at 24 W each). After 14 days of lamp irradiation, BDE-209 degraded with a half-life of 36 and 44 days, respectively, on montmorillonite or kaolinite, with much slower degradation occurring when sorbed on organic carbon-rich natural sediment (t1/2 = 150 days). In late summer and fall sunlight (40.5 degrees N, elevation 600 ft), the half-lives of BDE-209 sorbed on montmorillonite and kaolinite were 261 and 408 days, respectively. Under both irradiation schemes, no significant loss of BDE-209 occurred when sorbed to aluminum hydroxide, iron oxide (ferrihydrite), or manganese dioxide (birnessite). Upon exposure to both lamp and solar light and in the presence of montmorillonite and kaolinite, numerous lesser brominated congeners (tri- to nonabromodiphenyl ethers) were produced. Nearly identical product distribution was evident on montmorillonite and kaolinite. Dark control experiments for each mineral showed no disappearance of BDE-209 or appearance of degradation products. These results suggest that photodegradation of BDE-209 on mineral aerosols during long-range atmospheric transport may be an important fate process for BDE-209 in the environment.

Lead (II) removal from natural soils by enhanced electrokinetic remediation.

PubMed

Altin, Ahmet; Degirmenci, Mustafa

2005-01-20

Electrokinetic remediation is a very effective method to remove metal from fine-grained soils having low adsorption and buffering capacity. However, remediation of soil having high alkali and adsorption capacity via the electrokinetic method is a very difficult process. Therefore, enhancement techniques are required for use in these soil types. In this study, the effect of the presence of minerals having high alkali and cation exchange capacity in natural soil polluted with lead (II) was investigated by means of the efficiency of electrokinetic remediation method. Natural soil samples containing clinoptilolite, gypsum and calcite minerals were used in experimental studies. Moreover, a sample containing kaolinite minerals was studied to compare with the results obtained from other samples. Best results for soils bearing alkali and high sorption capacity minerals were obtained upon addition of 3 mol AcH and application of 20 V constant potential after a remediation period of 220 h. In these test conditions, lead (II) removal efficiencies for these samples varied between 60% and 70% up to 0.55 normalized distance. Under the same conditions, removal efficiencies in kaolinite sample varied between 50% and 95% up to 0.9 normalized distance.

Dielectrophoretic sample preparation for environmental monitoring of microorganisms: Soil particle removal.

PubMed

Fatoyinbo, Henry O; McDonnell, Martin C; Hughes, Michael P

2014-07-01

Detection of pathogens from environmental samples is often hampered by sensors interacting with environmental particles such as soot, pollen, or environmental dust such as soil or clay. These particles may be of similar size to the target bacterium, preventing removal by filtration, but may non-specifically bind to sensor surfaces, fouling them and causing artefactual results. In this paper, we report the selective manipulation of soil particles using an AC electrokinetic microfluidic system. Four heterogeneous soil samples (smectic clay, kaolinitic clay, peaty loam, and sandy loam) were characterised using dielectrophoresis to identify the electrical difference to a target organism. A flow-cell device was then constructed to evaluate dielectrophoretic separation of bacteria and clay in a continous flow through mode. The average separation efficiency of the system across all soil types was found to be 68.7% with a maximal separation efficiency for kaolinitic clay at 87.6%. This represents the first attempt to separate soil particles from bacteria using dielectrophoresis and indicate that the technique shows significant promise; with appropriate system optimisation, we believe that this preliminary study represents an opportunity to develop a simple yet highly effective sample processing system.

Rare earth minerals in a “no tonstein” section of the Dean (Fire Clay) coal, Knox County, Kentucky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hower, James C.; Berti, Debora; Hochella, Michael F.

The Dean (Fire Clay) coal in Knox County, Kentucky, does not contain the megascopically-visible ash-fall tonstein present in most other sections of the coal bed. Like the Fire Clay tonstein, a low-ash portion of the coal is enriched in rare earth elements (>2400 ppm, on ash basis). In addition to kaolinite produced in the diagenesis of volcanic glass, transmission electron microscopy studies indicate the coal contains primary kaolinite, LaCeNdTh monazite, barium niobate, native gold, and FeNiCr spinels. The mineral assemblages, particularly the kaolinite-monazite association and its similarity to the tonsteins in coal to the east, demonstrate the coal was subjectmore » to the REE-enriched volcanic ash fall, apparently just at a more dilute level than at locations where the tonstein is present.« less

Rare earth minerals in a “no tonstein” section of the Dean (Fire Clay) coal, Knox County, Kentucky

DOE PAGES

Hower, James C.; Berti, Debora; Hochella, Michael F.; ...

2018-05-03

The Dean (Fire Clay) coal in Knox County, Kentucky, does not contain the megascopically-visible ash-fall tonstein present in most other sections of the coal bed. Like the Fire Clay tonstein, a low-ash portion of the coal is enriched in rare earth elements (>2400 ppm, on ash basis). In addition to kaolinite produced in the diagenesis of volcanic glass, transmission electron microscopy studies indicate the coal contains primary kaolinite, LaCeNdTh monazite, barium niobate, native gold, and FeNiCr spinels. The mineral assemblages, particularly the kaolinite-monazite association and its similarity to the tonsteins in coal to the east, demonstrate the coal was subjectmore » to the REE-enriched volcanic ash fall, apparently just at a more dilute level than at locations where the tonstein is present.« less

Hydrothermal synthesis of ammonium illite

USGS Publications Warehouse

Šucha, Vladimír; Elsass, F.; Eberl, D.D.; Kuchta, L'.; Madejova, J.; Gates, W.P.; Komadel, P.

1998-01-01

Synthetic gel and glass of illitic composition, natural kaolinite, and mixed-layer illite-smectite were used as starting materials for hydrothermal synthesis of ammonium illite. Ammonium illite was prepared from synthetic gel by hydrothermal treatment at 300??C. The onset of crystallization began within 3 h, and well-crystallized ammonium illite appeared at 24 h. Increasing reaction time (up to four weeks) led to many illite layers per crystal. In the presence of equivalent proportions of potassium and ammonium, the gel was transformed to illite with equimolar contents of K and NH4. In contrast, synthesis using glass under the same conditions resulted in a mixture of mixed-layer ammonium illite-smectite with large expandability and discrete illite. Hydrothermal treatments of the fine fractions of natural kaolinite and illite-smectite produced ammonium illite from kaolinite but the illite-smectite remained unchanged.

Rock Deformation at High Confining Pressure and Temperature.

DTIC Science & Technology

debugged, delivered and installed to the contracting agency. Clay specimens of illite, kaolinite and montmorillonite were deformed in tri-axial compression...at 25 and 3000C at a constant confining pressure of 2 kb and a constant strain rate of .0001 sec. The illite and kaolinite are stronger under these...conditions than montmorillonite . Cores from dolomite single crystals were deformed at a confining pressure of 7 kb and temperatures of 300 and 500C

Shear wave velocity (Vs) anisotropy of kaolinite and fly ash kaolinite mixtures modified with controlled organics.

DOT National Transportation Integrated Search

2014-02-01

Anisotropy is an inherent property of soils. The anisotropy could either be induced by applied stress or inherent from particle : eccentricity and preferential deposition. Other than stress and deposition, the anisotropy was also found resulted from ...

Ore deposits and epithermal evidences associated with intra-magmatic faults at Aïn El Araâr-Oued Belif ring structure (NW of Tunisia)

NASA Astrophysics Data System (ADS)

Aissa, Wiem Ben; Aissa, Lassaâd Ben; Amara, Abdesslem Ben Haj; Tlig, Said; Alouani, Rabah

2017-03-01

Hydrothermal ore deposits at Aïn El Araâr-Oued Belif location are classified as epithermal deposits type. The ore bodies are hosted by upper Turonian (8-9 M.y) volcanic rhyodacitic complex. Polymetallic sulfide orebodies are mainly concentrated within intra-magmatic faults. Petrographic, XRD, and TEM-STEM investigations revealed that ore minerals are essentially, arsenopyrite, pyrite, chalcopyrite, pyrrhotite, hematite, goethite and magnetite with Au, Ag and Pt trace metals. Gangue minerals are mainly adularia, quartz, sericite, alunite, tridymite, chlorite, phlogopite and smectite. Epithermal alteration is well zoned with four successive characteristic zones: (1) zone of quartz-adularia-sericite and rare alunite; (2) zone of kaolinite and plagioclase albitization; (3) intermediate zone of illite-sericite; (4) sapropelic alteration type zone of chlorite-smectite and rare illite. This can be interpreted as a telescoping of two different acidity epithermal phases; low sulfidation (adularia-sericite) and high sulfidation (quartz-alunite), separated in time or due to a gradual increase of fluids acidity and oxicity within the same mineralization phase. Brecciated macroscopic facies with fragments hosting quartz-adularia-sericite minerals (low-sulfidation phase) without alunite, support the last hypothesis. Geodynamic context and mineral alteration patterns are closely similar to those of Maria Josefa gold mine at SE of Spain which exhibit a volcanic-hosted epithermal ore deposit in a similar vein system, within rhyolitic ignimbrites, altered to an argillic assemblage (illite-sericite abundant and subordinate kaolinite) that grades outwards into propylitic alteration (Sanger-von Oepen et al. (1990)). Mineralogical and lithologic study undertaken in the volcanic host rock at Aïn El Araâr-Oued Belif reveals a typical epithermal low-sulfidation and high-sulfidation ore deposits with dominance of low-sulfidation. Host rocks in these systems range from silicic to

Geology and Refractory Clay Deposits of the Haldeman and Wrigley Quadrangles, Kentucky

USGS Publications Warehouse

Patterson, Sam H.; Hosterman, John W.; Huddle, John Warfield

1962-01-01

The Haldeman and Wrigley 7th-minute quadrangles are near the western edge of the eastern Kentucky coal field and cover an area of approximately 117 square miles in parts of Carter, Rowan, Elliott, and Morgan Counties, Ky. The rocks exposed in the two quadrangles are of Early and Late Mississippian and Early and Middle Pennsylvanian age. The Mississippian rocks are composed of the thick Brodhead formation, which consists of siltstone and shale, and eleven thin marine limestone and shale formations, having an aggregate thickness of about 150 feet. The Lee and Breathitt formations, of Pennsylvanian age, consist of sandstone, siltstone, and shale; they also contain thin beds of coal and several beds of underclay, including the economically important Olive Hill clay bed of Crider, 1913. Pennsylvanian rocks include beds of both continental and marine origin. The eleven thin Mississippian formations and the upper-most part of the thick Brodhead formation are truncated by a prominent unconformity on which rocks of Pennsylvanian age rest. The rocks occupy a region of gentle dips between the Cincinnati arch and the Appalachian Mountains. Refractory clay deposits are in the Olive Hill clay bed, which occurs in the lower part of the Lee formation. The Olive Hill clay bed is discontinuous and consists of a series of irregularly shaped lenses. The bed is approximately two-thirds semifiint clay and one-third flint clay, and it contains minor amounts of plastic clay. Some of the flint clay is nearly pure kaolinite, but the semi flint and plastic clay consists of mixtures of kaolinite, illite, and mixed-layer clay minerals. The structure of the kaolinite ranges from highly crystalline to very poorly crystalline 'fireclay' type. The degree of crystallinity of the kaolinite and the hardness of the clay vary inversely with the amount of illite and mixed-layer clay minerals present. The nearly pure kaolinite is believed to have formed by the removal of alkalies and some silica fram

Extraction of hydrothermal alterations from ASTER SWIR data from east Zanjan, northern Iran

NASA Astrophysics Data System (ADS)

Azizi, H.; Tarverdi, M. A.; Akbarpour, A.

2010-07-01

The use of satellite images for mineral exploration has been very successful in pointing out the presence of minerals such as smectite and kaolinite which are important in the identification of hydrothermal alterations. Shortwave infrared (SWIR) bands from Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) with the wavelength of ASTER SWIR bands between 1.65 and 2.43 μm has a good potential for mapping a hydrothermal alteration minerals such as alunite, pyrophyllite, kaolinite, illite-muscovite-sericite, and carbonate. In this range, hydroxide minerals which have been produced by hydrothermal alteration exhibit good absorption compared to shorter or longer wavelengths. In this research which aims to remove atmospheric and topographic effects from ASTER SWIR data, the authors used the log-residual method (LRM) with the minimum noise fraction (MNF) transformation to create a pixel purity index (PPI) which was used to extract the most spectrally pure pixels from multispectral images. Spectral analyses of the clay mineralogy of the study area (east Zanjan, in northern Iran) were obtained by matching the unknown spectra of the purest pixels to the U.S. Geological Survey (USGS) mineral library. Three methods, spectral feature fitting (SFF), spectral angle mapping (SAM), and binary encoding (BE) were used to generate a score between 0 and 1, where a value of 1 indicates a perfect match showing the exact mineral type. In this way, it was possible to identify certain mineral classes, including chlorite, carbonate, calcite-dolomite-magnesite, kaolinite-smectite, alunite, and illite. In this research, two main propylitic and phyllic-argillic zones could be separated using their compositions of these minerals. These two alteration zones are important for porphyry copper deposits and gold mineralization in this part of Iran.

Creep and Sliding in Clays Slopes: Mutual Effects of Interlayer Swelling and Ice Jacking.

DTIC Science & Technology

1984-01-11

chlorite 14% (6-21%) calcite 6,5% (1 - 15%) kaolinite 2% ( 1- 5%) dolomite 0,5% (0 - 4%) montmorillonite 23% (15-35%) Non clay phases 19% (15-30%) Clay...iconcretions, 200 mm coal lenses RE 3 4 Calcite N Quartz Feldspar Illite-muscovite Z Chlorite E Kaolinite montmori 1 loni te Fig. 10: Mineral content... montmorillonite , belong to a fluviatile fresh water cycle and are possibly influenced by volcanic ash falls. The series under investigation belongs to the upper

Mobile colloid generation induced by a cementitious plume: mineral surface-charge controls on mobilization.

PubMed

Li, Dien; Kaplan, Daniel I; Roberts, Kimberly A; Seaman, John C

2012-03-06

Cementitious materials are increasingly used as engineered barriers and waste forms for radiological waste disposal. Yet their potential effect on mobile colloid generation is not well-known, especially as it may influence colloid-facilitated contaminant transport. Whereas previous papers have studied the introduction of cement colloids into sediments, this study examined the influence of cement leachate chemistry on the mobilization of colloids from a subsurface sediment collected from the Savannah River Site, USA. A sharp mobile colloid plume formed with the introduction of a cement leachate simulant. Colloid concentrations decreased to background concentrations even though the aqueous chemical conditions (pH and ionic strength) remained unchanged. Mobile colloids were mainly goethite and to a lesser extent kaolinite. The released colloids had negative surface charges and the mean particle sizes ranged primarily from 200 to 470 nm. Inherent mineralogical electrostatic forces appeared to be the controlling colloid removal mechanism in this system. In the background pH of ~6.0, goethite had a positive surface charge, whereas quartz (the dominant mineral in the immobile sediment) and kaolinite had negative surface charges. Goethite acted as a cementing agent, holding kaolinite and itself onto the quartz surfaces due to the electrostatic attraction. Once the pH of the system was elevated, as in the cementitious high pH plume front, the goethite reversed to a negative charge, along with quartz and kaolinite, then goethite and kaolinite colloids were mobilized and a sharp spike in turbidity was observed. Simulating conditions away from the cementitious source, essentially no colloids were mobilized at 1:1000 dilution of the cement leachate or when the leachate pH was ≤ 8. Extreme alkaline pH environments of cementitious leachate may change mineral surface charges, temporarily promoting the formation of mobile colloids.

Particle Tracking Model for Suspended Sediment Transport and Streambed Clogging Under Losing and Gaining Conditions

NASA Astrophysics Data System (ADS)

Preziosi-Ribero, A.; Fox, A.; Packman, A. I.; Escobar-Vargas, J.; Donado-Garzon, L. D.; Li, A.; Arnon, S.

2017-12-01

Exchange of mass, momentum and energy between surface water and groundwater is a driving factor for the biology, ecology and chemistry of rivers and water bodies in general. Nonetheless, this exchange is dominated by different factors like topography, bed morphology, and large-scale hydraulic gradient. In the particular case of fine sediments like clay, conservative tracer modeling is impossible because they are trapped in river beds for long periods, thus the normal advection dispersion approach leads to errors and results do not agree with reality. This study proposes a numerical particle tracking model that represents the behavior of kaolinite in a sand flume, and how its deposition varies according to different flow conditions, namely losing and gaining flow. Since fine particles do not behave like solutes, kaolinite dynamics are represented using settling velocity and a filtration coefficient allowing the particles to be trapped in the bed. This approach allows us to use measurable parameters directly related with the fine particle features as size and shape, and hydraulic parameters. Results are then compared with experimental results from lab experiments obtained in a recirculating flume, in order to assess the impact of losing and gaining conditions on sediment transport and deposition. Furthermore, our model is able to identify the zones where kaolinite deposition concentrates over the flume due to the bed geometry, and later relate these results with clogging of the bed and hence changes in the bed's hydraulic conductivity. Our results suggest that kaolinite deposition is higher under losing conditions since the vertical velocity of the flow is added to the deposition velocity of the particles modeled. Moreover, the zones where kaolinite concentrates varies under different flow conditions due to the difference in pressure and velocity in the river bed.

Subsurface application of poultry litter and its influence on nutrient losses in runoff water from permanent pastures.

PubMed

Watts, D B; Way, T R; Torbert, H A

2011-01-01

Environmental pressure to reduce nutrient losses from agricultural fields has increased in recent years. To abate this nutrient loss to the environment, better management practices and new technologies need to be developed. Thus, research was conducted to evaluate if subsurface banding poultry litter (PL) would reduce nitrogen (N) and phosphorus (P) loss in surface water runoff using a four-row prototype implement. Rainfall simulations were conducted to create a 40-min runoff event in an established bermudagrass (Cynodon dactylon L.) pasture on soil types common to the Coastal Plain and Piedmont regions. The Coastal Plain soil type was a Marvyn loamy sand (fine-loamy, kaolinitic, thermic Typic Kanhapludults) and the Piedmont soil type was a Hard Labor loamy sand (fine, kaolinitic, thermic Oxyaquic Kanhapludults). Treatments consisted of surface- and subsurface-applied PL at a rate of 9 Mg ha(-1), surface broadcast-applied commercial fertilizer (CF; urea and triple superphosphate blend) at the equivalent N (330 kg N ha(-1)) and P (315 kg N ha(-1)) content of PL, and a nonfertilized control. The greatest loss for inorganic N, total N, dissolved reactive P (DRP), and total P occurred with the surface broadcast treatments, with CF contributing to the greatest loss. Nutrient losses from the subsurface banded treatment reduced N and P in surface water runoff to levels of the control. Subsurface banding of PL reduced concentrations of inorganic N 91%, total N 90%, DRP 86%, and total P 86% in runoff water compared with surface broadcasted PL. These results show that subsurface band-applied PL can greatly reduce the impact of N and P loss to the environment compared with conventional surface-applied PL and CF practices.

Adsorption of guanidinium collectors on aluminosilicate minerals - a density functional study.

PubMed

Nulakani, Naga Venkateswara Rao; Baskar, Prathab; Patra, Abhay Shankar; Subramanian, Venkatesan

2015-10-07

In this density functional theory based investigation, we have modelled and studied the adsorption behaviour of guanidinium cations and substituted (phenyl, methoxy phenyl, nitro phenyl and di-nitro phenyl) guanidinium cationic collectors on the basal surfaces of kaolinite and goethite. The adsorption behaviour is assessed in three different media, such as gas, explicit water and pH medium, to understand the affinity of GC collectors to the SiO4 tetrahedral and AlO6 octahedral surfaces of kaolinite. The tetrahedral siloxane surface possesses a larger binding affinity to GC collectors than the octahedral sites due to the presence of surface exposed oxygen atoms that are active in the intermolecular interactions. Furthermore, the inductive electronic effects of substituted guanidinium cations also play a key role in the adsorption mechanism. Highly positive cations result in a stronger electrostatic interaction and preferential adsorption with the kaolinite surfaces than low positive cations. Computed interaction energies and electron densities at the bond critical points suggest that the adsorption of guanidinium cations on the surfaces of kaolinite and goethite is due to the formation of intra/inter hydrogen bonding networks. Also, the electrostatic interaction favours the high adsorption ability of GC collectors in the pH medium than gas phase and water medium. The structures and energies of GC collectors pave an intuitive view for future experimental studies on mineral flotation.

Organic-inorganic interactions at oil-water contacts: quantitative retracing of processes controlling the CO2 occurrence in Norwegian oil reservoirs

NASA Astrophysics Data System (ADS)

van Berk, Wolfgang; Schulz, Hans-Martin

2010-05-01

Crude oil quality in reservoirs can be modified by degradation processes at oil-water contacts (OWC). Mineral phase assemblages, composition of coexisting pore water, and type and amount of hydrocarbon degradation products (HDP) are controlling factors in complex hydrogeochemical processes in hydrocarbon-bearing siliciclastic reservoirs, which have undergone different degrees of biodegradation. Moreover, the composition of coexisting gas (particularly CO2 partial pressure) results from different pathways of hydrogeochemical equilibration. In a first step we analysed recent and palaeo-OWCs in the Heidrun field. Anaerobic decomposition of oil components at the OWC resulted in the release of methane and carbon dioxide and subsequent dissolution of feldspars (anorthite and adularia) leading to the formation of secondary kaolinite and carbonate phases. Less intensively degraded hydrocarbons co-occur with calcite, whereas strongly degraded hydrocarbons co-occur with solid solution carbonate phase (siderite, magnesite, calcite) enriched in δ13C. To test such processes quantitatively in a second step, CO2 equilibria and mass transfers induced by organic-inorganic interactions have been hydrogeochemically modelled in different semi-generic scenarios with data from the Norwegian continental shelf (acc. Smith & Ehrenberg 1989). The model is based on chemical thermodynamics and includes irreversible reactions representing hydrolytic disproportionation of hydrocarbons according to Seewald's (2006) overall reaction (1a) which is additionally applied in our modelling work in an extended form including acetic acid (1b): (1) R-CH2-CH2-CH3 + 4H2O -> R + 2CO2 + CH4 + 5H2, (2) R-CH2-CH2-CH3 + 4H2O -> R + 1.9CO2 + 0.1CH3COOH + 0.9CH4 + 5H2. Equilibrating mineral assemblages (different feldspar types, quartz, kaolinite, calcite) are based on the observed primary reservoir composition at 72 °C. Modelled equilibration and coupled mass transfer were triggered by the addition and reaction

Mapping of hydrothermally altered rocks using airborne multispectral scanner data, Marysvale, Utah, mining district

USGS Publications Warehouse

Podwysocki, M.H.; Segal, D.B.; Jones, O.D.

1983-01-01

Multispectral data covering an area near Marysvale, Utah, collected with the airborne National Aeronautics and Space Administration (NASA) 24-channel Bendix multispectral scanner, were analyzed to detect areas of hydrothermally altered, potentially mineralized rocks. Spectral bands were selected for analysis that approximate those of the Landsat 4 Thematic Mapper and which are diagnostic of the presence of hydrothermally derived products. Hydrothermally altered rocks, particularly volcanic rocks affected by solutions rich in sulfuric acid, are commonly characterized by concentrations of argillic minerals such as alunite and kaolinite. These minerals are important for identifying hydrothermally altered rocks in multispectral images because they have intense absorption bands centered near a wavelength of 2.2 ??m. Unaltered volcanic rocks commonly do not contain these minerals and hence do not have the absorption bands. A color-composite image was constructed using the following spectral band ratios: 1.6??m/2.2??m, 1.6??m/0.48??m, and 0.67??m/1.0??m. The particular bands were chosen to emphasize the spectral contrasts that exist for argillic versus non-argillic rocks, limonitic versus nonlimonitic rocks, and rocks versus vegetation, respectively. The color-ratio composite successfully distinguished most types of altered rocks from unaltered rocks. Some previously unrecognized areas of hydrothermal alteration were mapped. The altered rocks included those having high alunite and/or kaolinite content, siliceous rocks containing some kaolinite, and ash-fall tuffs containing zeolitic minerals. The color-ratio-composite image allowed further division of these rocks into limonitic and nonlimonitic phases. The image did not allow separation of highly siliceous or hematitically altered rocks containing no clays or alunite from unaltered rocks. A color-coded density slice image of the 1.6??m/2.2??m band ratio allowed further discrimination among the altered units. Areas

Hydrogen and oxygen isotope exchange reactions between clay minerals and water

USGS Publications Warehouse

O'Neil, J.R.; Kharaka, Y.K.

1976-01-01

The extent of hydrogen and oxygen isotope exchange between clay minerals and water has been measured in the temperature range 100-350?? for bomb runs of up to almost 2 years. Hydrogen isotope exchange between water and the clays was demonstrable at 100??. Exchange rates were 3-5 times greater for montmorillonite than for kaolinite or illite and this is attributed to the presence of interlayer water in the montmorillonite structure. Negligible oxygen isotope exchange occurred at these low temperatures. The great disparity in D and O18 exchange rates observed in every experiment demonstrates that hydrogen isotope exchange occurred by a mechanism of proton exchange independent of the slower process of O18 exchange. At 350?? kaolinite reacted to form pyrophyllite and diaspore. This was accompanied by essentially complete D exchange but minor O18 exchange and implies that intact structural units in the pyrophyllite were inherited from the kaolinite precursor. ?? 1976.

Isotopic evidence for cooler and drier conditions in the tropical Andes during the last glacial stage

NASA Astrophysics Data System (ADS)

Mora, Germán; Pratt, Lisa M.

2001-06-01

Documentation of paleoclimatic conditions during the last glacial stage in the tropical Andes is sparse despite the importance of understanding past climate changes in the tropics. To reconstruct paleoenvironmental conditions in the alpine neotropics, we measured the oxygen (δ18O) and hydrogen (δD) isotopic composition of authigenic kaolinite within weathering profiles of the Bogota basin (Colombia) because of the strong dependence of isotopic values on both surface temperature and rainfall. While kaolinite isotope data from Holocene soils in the basin reflect modern mean annual temperature and mean weighted rainwater isotopic composition of the basin, kaolinite isotope data from paleosols developed during the last glacial stage suggest 6 ± 2 °C cooler temperatures. Moreover, the isotope data indicate higher isotopic values of paleorainwater, interpreted to reflect drier conditions. The combination of reduced rainfall, temperature, and pCO2 significantly affected the distribution of tropical montane flora during the last glacial stage.

Effects of clay minerals on transport of graphene oxide in saturated porous media.

PubMed

Lu, Taotao; Xia, Tianjiao; Qi, Yu; Zhang, Chengdong; Chen, Wei

2017-03-01

The presence of kaolinite, montmorillonite, and illite in packed quartz sand inhibited the transport of graphene oxide to different degrees. Transport inhibition was exerted mainly by the presence of positively charged sites on clay edges (which served as favorable deposition sites), whereas the effects on the overall particle-collector interaction energy and flow path were small. Kaolinite exhibited the most significant transport-inhibition effects because of its high percentage of edge area. Environ Toxicol Chem 2017;36:655-660. © 2016 SETAC. © 2016 SETAC.

Association of actinides with microorganisms and clay: Implications for radionuclide migration from waste-repository sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohnuki, T.; Francis, A.; Kozai, N.

2010-04-01

We conducted a series of basic studies on the microbial accumulation of actinides to elucidate their migration behavior around backfill materials used in the geological disposal of radioactive wastes. We explored the interactions of U(VI) and Pu(VI) with Bacillus subtilis, kaolinite clay, and within a mixture of the two, directly analyzing their association with the bacterium in the mixture by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). The accumulation of U by the mixture rose as the numbers of B. subtilis cells increased. Treating the kaolinite with potassium acetate (CH{sub 3}COOK) removed approximately 80% of the associated uraniummore » while only 65% was removed in the presence of B. subtilis. TEM-EDS analysis confirmed that most of the U taken from solution was associated with B. subtilis. XANES analyses revealed that the oxidation state of uranium associated with B. subtilis, kaolinite, and with the mixture containing both was U(VI). The amount of Pu sorbed by B. subtilis increased with time, but did not reach equilibrium in 48 h; in kaolinite alone, equilibrium was attained within 8 h. After 48 h, the oxidation state of Pu in the solutions exposed to B. subtilis and to the mixture had changed to Pu(V), whereas the oxidation state of the Pu associated with both was Pu(IV). In contrast, there was no change in the oxidation state of Pu in the solution nor on kaolinite after exposure to Pu(VI). SEM-EDS analysis indicated that most of the Pu in the mixture was associated with the bacteria. These results suggest that U(VI) and Pu(VI) preferentially are sorbed to bacterial cells in the presence of kaolinite clay, and that the mechanism of accumulation of U and Pu differs. U(VI) is sorbed directly to the bacterial cells, whereas Pu(VI) first is reduced to Pu(V) and then to Pu(IV), and the latter is associated with the cells. These results have important implications on the migrations of radionuclides around the repository sites

Function of minerals in the natural radioactivity level of Vaigai River sediments, Tamilnadu, India--spectroscopical approach.

PubMed

Ramasamy, V; Paramasivam, K; Suresh, G; Jose, M T

2014-01-03

Using Gamma ray and Fourier Transform Infrared (FTIR) spectroscopic techniques, level of natural radioactivity ((238)U, (232)Th and (40)K) and mineralogical characterization of Vaigai River sediments have been analyzed with the view of evaluating the radiation risk and its relation to available minerals. Different radiological parameters are calculated to know the entire radiological characterization. The average of activity concentrations and all radiological parameters are lower than the recommended safety limit. However, some sites are having higher radioactivity values than the safety limit. From the FTIR spectroscopic technique, the minerals such as quartz, microcline feldspar, orthoclase feldspar, kaolinite, gibbsite, calcite, montmorillonite and organic carbon are identified and they are characterized. The extinction co-efficient values are calculated to know the relative distribution of major minerals such as quartz, microcline feldspar, orthoclase feldspar and kaolinite. The calculated values indicate that the amount of quartz is higher than orthoclase feldspar, microcline feldspar and much higher than kaolinite. Crystallinity index is calculated to know the crystalline nature of quartz and the result indicates that the presence of ordered crystalline quartz in the present sediment. The role of minerals in the level of radioactivity is assessed by multivariate statistical analysis (Pearson's correlation and Cluster analysis). The statistical analysis confirms that the clay mineral kaolinite is the major factor than other major minerals to induce the important radioactivity variables such as absorbed dose rate and concentrations of (232)Th and (238)U. Copyright © 2013 Elsevier B.V. All rights reserved.

Natural and ion-exchanged illite clays reduce bacterial burden and inflammation in cutaneous meticillin-resistant Staphylococcus aureus infections in mice

PubMed Central

Otto, Caitlin C.; Kilbourne, Jacquelyn

2016-01-01

Discoveries associated with antibacterial activity of hydrated clays necessitate assessments of in vivo efficacy, practical use and safety. Surface properties of clays can lead to variations in the composition and abundance of bound compounds or ions, thus affecting antibacterial activity. Since exchangeable metal ions released from the clay surface are responsible for in vitro antibacterial activity, we evaluated the in vivo antibacterial efficacy of four natural clays (one illite clay, two montmorillonite clays and one kaolinite clay) and three ion-exchanged, antibacterial clays against superficial, cutaneous meticillin-resistant Staphylococcus aureus (MRSA) infections in mice. Superficial, cutaneous wounds on the back of SKH1-Elite mice were generated and subsequently infected with MRSA. Following twice daily applications of a hydrated clay poultice to infected wounds for 7 days, we observed significant differences in the in vivo antibacterial efficacy between different types of clays. The natural and ion-exchanged illite clays performed best, as measured by bacterial load, inflammatory response and gross wound morphology with significant decreases in bacterial viability and dermatitis. Topical application of kaolinite clay was the least effective, resulting in the lowest decrease in bacterial load and exhibiting severe dermatitis. These data suggest that specific types of clays may offer a complementary and integrative strategy for topically treating MRSA and other cutaneous infections. However, since natural clays exhibit in vitro antibacterial variability and vary vastly in surface chemistries, adsorptive/absorptive characteristics and structural composition, the properties and characteristics of illite clays could aid in the development of standardized and customized aluminosilicates for topical infections. PMID:26508716

Type Region of the Ione Formation (Eocene), Central California: Stratigraphy, Paleogeography, and Relation to Auriferous Gravels

USGS Publications Warehouse

Creely, Scott; Force, Eric R.

2007-01-01

The middle Eocene Ione Formation extends over 200 miles (320 km) along the western edge of the Sierra Nevada. Our study was concentrated in the type region, 30 miles (48 km) along strike. There a bedrock ridge forms the seaward western side of the Ione depositional tract, defining a subbasin margin. The eastern limit of the type Ione is locally defined by high-angle faults. Ione sediments were spread over Upper Mesozoic metamorphic and plutonic bedrock, fed by gold-bearing streams dissecting the western slope of the ancestral Sierra Nevada. By middle Eocene time, a tropical or subtropical climate prevailed, leading to deep chemical weathering (including laterization) and a distinctively mature mineral assemblage was fed to and generated within Ione deposits. The Ione is noted for its abundant kaolinitic clay, some of it coarsely crystalline; the clay is present as both detrital grains and authigenic cement. Quartz is abundant, mostly as angular grains. Heavy mineral fractions are dominated by altered ilmenite and zircon. Distribution of feldspar is irregular, both stratigraphically and areally. Non-marine facies are most voluminous, and include conglomerates, especially at the base and along the eastern margins of the formation where they pass into Sierran auriferous gravels. Clays, grading into lignites, and gritty sands are also common facies. Both braided and meandering fluvial facies have been recognized. Shallow marine waters flooded the basin probably twice. Tongues of sediment exhibiting a variety of estuarine to marine indicators are underlain and overlain by fluvial deposits. Marine body fossils are found at only a few localities, but burrows identified as Ophiomorpha and cf. Thalassinoides are abundant in many places. Other clues to marginal marine deposition are the occurrence of glauconite in one bed, typical relations of lagoonal to beach (locally heavy-mineral-rich) lithofacies, closed-basin three-dimensional morphology of basinal facies, and high

Epithermal gold-siver deposits in the western United States: time-space products of evolving plutonic, volcanic and tectonic environments

USGS Publications Warehouse

Berger, Byron R.; Bonham, Harold F.

1990-01-01

The western United States has been the locus of considerable subaerial volcanic and plutonic igneous activity since the mid-Mesozoic. After the destruction of the Jurassic-Cretaceous magmatic arc-trench system, subduction was re-established in the Late Mesozoic with low-angle underthrusting of the oceanic plate beneath western North America. This resulted in crustal shortening during the Late Cretaceous to Early Tertiary and removal of the mantle lithosphere west of the Rocky Mountains. Commencing in the Eocene, flat subduction ceased, the volcanic arc began to re-establish itself along the continental margin, and the hingeline along the steepening subducting plate migrated from east to west. The crust east of the migrating hingeline was exposed to hot asthenosphere, and widespread tectonics and volcanic activity resulted. Hydrothermal activity accompanied the volcanism resulting in numerous epithermal gold-silver deposits. The temporal and spatial distributions of epithermal deposits in the region are therefore systematic and can be subdivided into discrete time intervals which are related to widespread changes in magmatic activity. Time intervals selected for discussion are Pre-Cenozoic, 66-55 Ma, 54-43 Ma, 42-34 Ma, 33-24 Ma, 23-17 Ma, and <17 Ma. Many of these intervals contain both sedimentary-rock and two varieties of volcanic-rock hosted deposits (adularia-sericite and alunite-kaolinite ± pyrophyllite). Continental rifting is important to the formation of deposits, and, within any given region, it is at the initiation of deep rifting that alunite-kaolinite ± pyrophyllite type epithermal deposits are formed. Adularia-sericite type deposits are most common, being related to all compositions and styles of volcanic activity. Therefore, the volcano-tectonic context of the western United States provides a unified framework in which to understand and explore for epithermal type deposits.

Direct-on-Filter α-Quartz Estimation in Respirable Coal Mine Dust Using Transmission Fourier Transform Infrared Spectrometry and Partial Least Squares Regression.

PubMed

Miller, Arthur L; Weakley, Andrew Todd; Griffiths, Peter R; Cauda, Emanuele G; Bayman, Sean

2017-05-01

In order to help reduce silicosis in miners, the National Institute for Occupational Health and Safety (NIOSH) is developing field-portable methods for measuring airborne respirable crystalline silica (RCS), specifically the polymorph α-quartz, in mine dusts. In this study we demonstrate the feasibility of end-of-shift measurement of α-quartz using a direct-on-filter (DoF) method to analyze coal mine dust samples deposited onto polyvinyl chloride filters. The DoF method is potentially amenable for on-site analyses, but deviates from the current regulatory determination of RCS for coal mines by eliminating two sample preparation steps: ashing the sampling filter and redepositing the ash prior to quantification by Fourier transform infrared (FT-IR) spectrometry. In this study, the FT-IR spectra of 66 coal dust samples from active mines were used, and the RCS was quantified by using: (1) an ordinary least squares (OLS) calibration approach that utilizes standard silica material as done in the Mine Safety and Health Administration's P7 method; and (2) a partial least squares (PLS) regression approach. Both were capable of accounting for kaolinite, which can confound the IR analysis of silica. The OLS method utilized analytical standards for silica calibration and kaolin correction, resulting in a good linear correlation with P7 results and minimal bias but with the accuracy limited by the presence of kaolinite. The PLS approach also produced predictions well-correlated to the P7 method, as well as better accuracy in RCS prediction, and no bias due to variable kaolinite mass. Besides decreased sensitivity to mineral or substrate confounders, PLS has the advantage that the analyst is not required to correct for the presence of kaolinite or background interferences related to the substrate, making the method potentially viable for automated RCS prediction in the field. This study demonstrated the efficacy of FT-IR transmission spectrometry for silica determination in

Direct-on-Filter α-Quartz Estimation in Respirable Coal Mine Dust Using Transmission Fourier Transform Infrared Spectrometry and Partial Least Squares Regression

PubMed Central

Miller, Arthur L.; Weakley, Andrew Todd; Griffiths, Peter R.; Cauda, Emanuele G.; Bayman, Sean

2017-01-01

In order to help reduce silicosis in miners, the National Institute for Occupational Health and Safety (NIOSH) is developing field-portable methods for measuring airborne respirable crystalline silica (RCS), specifically the polymorph α-quartz, in mine dusts. In this study we demonstrate the feasibility of end-of-shift measurement of α-quartz using a direct-on-filter (DoF) method to analyze coal mine dust samples deposited onto polyvinyl chloride filters. The DoF method is potentially amenable for on-site analyses, but deviates from the current regulatory determination of RCS for coal mines by eliminating two sample preparation steps: ashing the sampling filter and redepositing the ash prior to quantification by Fourier transform infrared (FT-IR) spectrometry. In this study, the FT-IR spectra of 66 coal dust samples from active mines were used, and the RCS was quantified by using: (1) an ordinary least squares (OLS) calibration approach that utilizes standard silica material as done in the Mine Safety and Health Administration's P7 method; and (2) a partial least squares (PLS) regression approach. Both were capable of accounting for kaolinite, which can confound the IR analysis of silica. The OLS method utilized analytical standards for silica calibration and kaolin correction, resulting in a good linear correlation with P7 results and minimal bias but with the accuracy limited by the presence of kaolinite. The PLS approach also produced predictions well-correlated to the P7 method, as well as better accuracy in RCS prediction, and no bias due to variable kaolinite mass. Besides decreased sensitivity to mineral or substrate confounders, PLS has the advantage that the analyst is not required to correct for the presence of kaolinite or background interferences related to the substrate, making the method potentially viable for automated RCS prediction in the field. This study demonstrated the efficacy of FT-IR transmission spectrometry for silica determination in

AMS Fabric of a CRM in Hematite-Bearing Samples: Evidence of DRMs in Natural Red Beds

NASA Astrophysics Data System (ADS)

Kodama, K. P.

2002-12-01

Anisotropy of magnetic susceptibility (AMS) and anisotropy of isothermal remanence (AIR) in red sedimentary rocks both typically show a bedding parallel foliation with minimum axes clustered perpendicular to the bedding plane. Our studies have observed this type of magnetic fabric in red bed units that have a range of ages and come from widespread localities. These units include the Mississippian Mauch Chunk Formation from the Appalachians, the Triassic Passaic Formation from the Newark basin in Pennsylvania, the Cretaceous Kapusaliang Formation from the Tarim basin in China, and the early Mesozoic Kayenta and Chinle Formations from the Colorado Plateau in southwestern North America. Bedding parallel foliations are also observed in magnetite-bearing rocks that carry a depositional remanence (DRM), suggesting the possibility of a DRM in red beds, even though the conventional wisdom is that they carry a post-depositional chemical remanent magnetization (CRM). Before the typical magnetic fabric of red beds can be used to indicate their type of remanence, we must determine what the magnetic fabric of a CRM looks like. For this reason, I conducted a series of hematite-growth experiments following the procedures outlined by Stokking and Tauxe (1987). I grew hematite in the laboratory on stacks of glass-fiber filter papers and in slurries of quartz and kaolinite. The hematite was grown from a ferric nitrate solution heated to 95° C for 8 hours. The samples were then dehydrated in a vacuum at room temperature for approximately 38 hours. It was possible to thermally demagnetize the eight filter paper samples to 350° C, but the six kaolinite-quartz samples were grown in plastic sample cubes and could only be thermally demagnetized to 150° C, enough to remove the thermoviscous magnetization acquired by the samples during the heating at 95° C. The mean CRM acquired by the red-brown magnetic phase grown in the experiments was within its alpha-95 of the steeply inclined

Interaction between ATP, metal ions, glycine, and several minerals

NASA Technical Reports Server (NTRS)

Rishpon, J.; Ohara, P. J.; Lawless, J. G.; Lahav, N.

1982-01-01

Interactions between ATP, glycine and montmorillonite and kaolinite clay minerals in the presence of various metal cations are investigated. The adsorption of adenine nucleotides on clays and Al(OH)3 was measured as a function of pH, and glycine condensation was followed in the presence of ATP, ZnCl2, MgCl2 and either kaolinite or montmorillonite. The amounts of ATP and ADP adsorbed are found to decrease with increasing Ph, and to be considerably enhanced in experiments with Mg(2+)- and Zn(2+)-montmorillonite with respect to Na(+)-montmorillonite. The effects of divalent cations are less marked in kaolinite. Results for Al(OH)3 show the importance of adsorption at clay platelet edges at high pH. The decomposition of ATP during drying at high temperature is observed to be inhibited by small amounts of clay, vacuum, or Mg(2+) or Zn(2+) ions, and to be accompanied by peptide formation in the presence of glycine. Results suggest the importance of Zn(2+) and Mg(2+) in chemical evolution.

Montmorillonite enhanced ciprofloxacin transport in saturated porous media with sorbed ciprofloxacin showing antibiotic activity

NASA Astrophysics Data System (ADS)

Chen, Hao; Gao, Bin; Yang, Liu-Yan; Ma, Lena Q.

2015-02-01

Antibiotic ciprofloxacin (CIP) is immobile in the subsurface but it has been frequently detected in the aquatic system. Therefore it is important to investigate the factors impacting CIP's mobilization in aquifer. Laboratory columns packed with sand were used to test colloid-facilitated CIP transport by 1) using kaolinite or montmorillonite to mobilize presorbed-CIP in a column or 2) co-transporting with CIP by pre-mixing them before transport. The Langmuir model showed that CIP sorption by montmorillonite (23 g kg- 1) was 100 times more effective than sand or kaolinite. Even with strong CIP complexation ability to Fe/Al coating on sand surface, montmorillonite promoted CIP transport, but not kaolinite. All presorbed-CIP by sand was mobilized by montmorillonite after 3 pore volumes through co-transporting of CIP with montmorillonite. The majority of CIP was fixed onto the montmorillonite interlayer but still showed inhibition of bacteria growth. Our results suggested that montmorillonite with high CIP sorption ability can act as a carrier to enhance CIP's mobility in aquifer.

Clay pigment structure characterisation as a guide for provenance determination--a comparison between laboratory powder micro-XRD and synchrotron radiation XRD.

PubMed

Švarcová, Silvie; Bezdička, Petr; Hradil, David; Hradilová, Janka; Žižak, Ivo

2011-01-01

Application of X-ray diffraction (XRD)-based techniques in the analysis of painted artworks is not only beneficial for indisputable identification of crystal constituents in colour layers, but it can also bring insight in material crystal structure, which can be affected by their geological formation, manufacturing procedure or secondary changes. This knowledge might be helpful for art historic evaluation of an artwork as well as for its conservation. By way of example of kaolinite, we show that classification of its crystal structure order based on XRD data is useful for estimation of its provenance. We found kaolinite in the preparation layer of a Gothic wall painting in a Czech church situated near Karlovy Vary, where there are important kaolin deposits. Comparing reference kaolin materials from eight various Czech deposits, we found that these can be differentiated just according to the kaolinite crystallinity. Within this study, we compared laboratory powder X-ray micro-diffraction (micro-XRD) with synchrotron radiation X-ray diffraction analysing the same real sample. We found that both techniques led to the same results.

Chemical weathering in a tropical watershed, Luquillo Mountains, Puerto Rico: II. Rate and mechanism of biotite weathering

USGS Publications Warehouse

Murphy, S.F.; Brantley, S.L.; Blum, A.E.; White, A.F.; Dong, H.

1998-01-01

Samples of soil, saprolite, bedrock, and porewater from a lower montane wet forest, the Luquillo Experimental Forest (LEF) in Puerto Rico, were studied to investigate the rates and mechanisms of biotite weathering. The soil profile, at the top of a ridge in the Rio Icacos watershed, consists of a 50-100-cm thick layer of unstructured soil above a 600-800 cm thick saprolite developed on quartz diorite. The only minerals present in significant concentration within the soil and saprolite are biotite, quartz, kaolinite, and iron oxides. Biotite is the only primary silicate releasing significant K and Mg to porewaters. Although biotite in samples of the quartz diorite bedrock is extensively chloritized, chlorite is almost entirely absent in the saprolite phyllosilicates. Phyllosilicate grains are present as 200-1000 ??m wide books below about 50 cm depth. X-ray diffraction (XRD) and electron microprobe analyses indicate that the phyllosilicate grains contain a core of biotite surrounded by variable amounts of kaolinite. Lattice fringe images under transmission electron microscope (TEM) show single layers of biotite altering to two layers of kaolinite, suggesting dissolution of biotite and precipitation of kaolinite at discrete boundaries. Some single 14-A?? layers are also observed in the biotite under TEM. The degree of kaolinitization of individual phyllosilicate grains as observed by TEM decreases with depth in the saprolite. This TEM work is the first such microstructural evidence of epitaxial growth of kaolinite onto biotite during alteration in low-temperature environments. The rate of release of Mg in the profile, calculated as a flux through the soil normalized per watershed land area, is approximately 500 mol hectare-1 yr-1 (1.6 ?? 10-9 molMg m-2soil s-1). This rate is similar to the flux estimated from Mg discharge out the Rio Icacos (1000 mol hectare-1 yr-1, or 3.5 ?? 10-9 molMg m-2soil s-1), indicating that scaling up from the soil to the watershed is

Pyritized mudstone and associated facies in the Permian-Triassic boundary of the Çürük Daǧ section, Southern Turkey

NASA Astrophysics Data System (ADS)

Varol, Baki; Koşun, Erdal; Ünal Pinar, Neslihan; Ayranci, Korhan

2011-03-01

This paper is the first study of pyritized mudstones (PM) in the Permian-Triassic (P-T) boundary section of the Çürük Dağ (Taurus, Antalya Nappes, Turkey). The mudstones were generally formed as lensoidal-shaped layers or infill materials within nodular platform limestones (hardground). Normal marine fauna is diminished in the pyritized limestones, whereas tube-like microorganisms are apparently increased with the association of pyrite crystals consisting of both framboidal and cubic crystals. The total rock volumes are up to 50-60% clay minerals and are mainly made up of in situ kaolinite and subordinate mixed layer clays (illite-vermiculite). Kaolinite preferentially developed on feldspar crystals, sometimes covering ostracoda bivalves together with gypsum micronodules composed of fan-shaped gypsum crystals. The origin of the kaolinite is, in situ, directly related to feldspar dissolution via heterotrophic bacteria. Thus, kaolinite is found along with bacterial structures. Other mineralogical compositions include established quartz (mostly β-quartz), gypsum crystals (100-200 μm) glauconite and magnetite. Magnetite grains comprise a minor amount (1-2%) and show some bacterial-induced crystal orientations. Glauconite is formed as an accessory mineral that occurs as infill material in biogenic grains. On the other hand, some microspheres represented by a silica-dominated composition are only observed in scanning electron microscopes (SEM) studies under high magnification. Isotope values (d34S) obtained from the pyritized mudstones show an isotopic heterogeneity that suggests that the pyritized mudstone consists of at least two components, with different sulphur-concentrations and d34S values.

Intensity and duration of chemical weathering: An example from soil clays of the southeastern Koolau Mountains, Oahu, Hawaii

USGS Publications Warehouse

Johnsson, Mark J.; Ellen, Stephen D.; McKittrick, Mary Anne

1993-01-01

Orographic precipitation on the southern flank of the southeastern Koolau Mountains produces a pronounced precipitation gradient. The corresponding gradient in the intensity of the chemical weathering environment provides an opportunity to address the effects of varying chemical weathering intensity on the composition of clay-size weathering products in soils developed on basalt. In addition, little-modified remnants of the constructional surface of the Koolau Volcano, isolated by stream dissection, remain as facets on the southern ends of the parallel ridges of the study area. By comparing clay mineralogy of soils developed on these older geomorphic surfaces with those developed on the younger sharp-crested ridges and steep side slopes, the effects of weathering duration on clay mineralogy can also be addressed.Soil clays in this part of the Koolau Mountains are mineralogically complex; principal phases include smectite, kaolinite, and halloysite, but pure end member phases are uncommon. Rather, most phases contain some amount of mixed layering. Smectite may contain small (<5%) amounts of randomly interstratified halloysite. Similarly, kaolinite commonly contains a small proportion of halloysite interlayers. A complex halloysitic phase shows evidence of interstratification with both smectite and kaolinite. Nonphyllosilicates found in the clay fraction include gibbsite, goethite, rare quartz, and perhaps cristobalite.The gradient in precipitation is reflected in soil clay mineralogy by varying proportions of dominantly smectitic, kaolinitic, and halloysitic phases. In regions of relatively low precipitation (<2,000 mm/yr), soils are dominated by the smectitic and halloysitic phases. With increased precipitation (as much as ∼4,000 mm/yr), kaolinitic and halloysitic phases become the dominant clay minerals, and goethite and gibbsite become increasingly abundant.Older soils developed on geomorphic surfaces representing the original constructional surface of Koolau

Influence of Compositional Variations on Floc Size and Strength

NASA Astrophysics Data System (ADS)

Yin, H.; Tan, X.; Reed, A. H.; Furukawa, Y.; Zhang, G.

2010-12-01

, resulting in different shearing stress in the fluid. Experimental results show that organic biopolymers can have profound influences on clay flocculation process and the resultant floc size and strength. Anionic xanthan gum tends to form smaller and weaker clay-biopolymer flocs than neutral guar gum, because the Coulombic repulsion forces develop between the two negatively charged constituents. Illite results in stronger clay-guar flocs than kaolinite, probably due to the relatively higher negative charges on illite surface. Generally, a bimodal distribution of floc size frequency was observed for all types of flocs. The maxim floc sizes range from 10-30 μm for kaolinite-xanthan flocs to 250-300 μm for kaolinite-guar flocs at a weight ratio of 1:1.

One-dimensional pore pressure diffusion of different grain-fluid mixtures

NASA Astrophysics Data System (ADS)

von der Thannen, Magdalena; Kaitna, Roland

2015-04-01

During the release and the flow of fully saturated debris, non-hydrostatic fluid pressure can build up and probably dissipate during the event. This excess fluid pressure has a strong influence on the flow and deposition behaviour of debris flows. Therefore, we investigate the influence of mixture composition on the dissipation of non-hydrostatic fluid pressures. For this we use a cylindrical pipe of acrylic glass with installed pore water pressure sensors in different heights and measure the evolution of the pore water pressure over time. Several mixtures with variable content of fine sediment (silt and clay) and variable content of coarse sediment (with fixed relative fractions of grains between 2 and 32 mm) are tested. For the fines two types of clay (smectite and kaolinite) and loam (Stoober Lehm) are used. The analysis is based on the one-dimensional consolidation theory which uses a diffusion coefficient D to model the decay of excess fluid pressure over time. Starting from artificially induced super-hydrostatic fluid pressures, we find dissipation coefficients ranging from 10-5 m²/s for liquid mixtures to 10-8 m²/s for viscous mixtures. The results for kaolinite and smectite are quite similar. For our limited number of mixtures the effect of fines content is more pronounced than the effect of different amounts of coarse particles.

The Role of Protein-Mineral Interactions for Protein Adsorption or Fragmentation

NASA Astrophysics Data System (ADS)

Chacon, S. S.; Reardon, P.; Washton, N.; Kleber, M.

2014-12-01

Soil exo-enzymes (EE) are proteins with the capability to catalyze the depolymerization of soil organic matter (SOM). SOM must be disassembled by EEs in order to be transported through the microbial cell wall and become metabolized. One factor determining an EE's functionality is their affinity to mineral surfaces found in the soil. Our goal was to establish the range of protein modifications, either chemical or structural, as the protein becomes associated with mineral surfaces. We hypothesized that pedogenic oxides would generate more extensive chemical alterations to the protein structure than phyllosilicates. A well-characterized protein proxy (Gb1, IEP 4.0, 6.2 kDA) was adsorbed onto functionally different mineral surfaces (goethite, montmorillonite, kaolinite and birnesite) at pH 5 and pH 7. We used 1H 15N Heteronuclear Single Quantum Coherence Nuclear Magnetic Resonance Spectroscopy (HSQC NMR) to observe structural modifications in the unadsorbed Gb1 that was allowed to equilibrate during the adsorption process for kaolinite, goethite and birnessite. Solid state NMR was used to observe the structural modifications of Gb1 while adsorbed onto kaolinite and montmorillonite. Preliminary results in the HSQC NMR spectra observed no changes in the native conformation of Gb1 when allowed to interact with goethite and kaolinite while birnessite induced strong structural modification of Gb1 at an acidic pH. Our results suggest that not all mineral surfaces in soil act as sorbents for EEs and changes in their catalytic activity upon adsorption to minerals surfaces may not just be an indication of conformational changes but of fragmentation of the protein itself.

Bioavailability of methyl parathion adsorbed on clay minerals and iron oxide.

PubMed

Cai, Peng; He, Xiaomin; Xue, Aifang; Chen, Hao; Huang, Qiaoyun; Yu, Jun; Rong, Xinming; Liang, Wei

2011-01-30

Adsorption, desorption and degradation by Pseudomonas putida of methyl parathion (O,O-dimethyl O-p-nitrophenyl phosphorothioate) on montmorillonite, kaolinite and goethite were studied. Metabolic activities of methyl parathion-degrading bacteria P. putida in the presence of minerals were also monitored by microcalorimetry to determine the degradation mechanism of methyl parathion. Montmorillonite presented higher adsorption capacity and affinity for methyl parathion than kaolinite and goethite. The percentage of degradation of methyl parathion adsorbed on minerals by P. putida was in the order of montmorillonite>kaolinite>goethite. The presence of minerals inhibited the exponential growth and the metabolic activity of P. putida. Among the examined minerals, goethite exhibited the greatest inhibitory effect on bacterial activity, while montmorillonite was the least depressing. The biodegradation of adsorbed methyl parathion by P. putida is apparently not controlled by the adsorption affinity of methyl parathion on minerals and may be mainly governed by the activity of the methyl parathion-degrading bacteria. The information obtained in this study is of fundamental significance for the understanding of the behavior of methyl parathion in soil environments. Copyright © 2010 Elsevier B.V. All rights reserved.

Ceramic media amended with metal oxide for the capture of viruses in drinking water.

PubMed

Brown, J; Sobsey, M D

2009-04-01

Ceramic materials that can adsorb and/or inactivate viruses in water may find widespread application in low-tech drinking-water treatment technologies in developing countries, where porous ceramic filters and ceramic granular media filters are increasingly promoted for that purpose. We examined the adsorption and subsequent inactivation of bacteriophages MS2 and (phiX-174 on five ceramic media in batch adsorption studies to determine media suitability for use in a ceramic water filter application. The media examined were a kaolinitic ceramic medium and four kaolinitic ceramic media amended with iron or aluminium oxides that had been incorporated into the kaolinitic clays before firing. Batch adsorption tests indicate increased sorption and inactivation of surrogate viruses by media amended with Fe and Al oxide, with FeOOH-amended ceramic inactivating all bacteriophages up to 8 log10. Unmodified ceramic was a poor adsorbent of bacteriophages at less than 1 log10 adsorption-inactivation and high recovery of sorbed phages. These studies suggest that contact with ceramic media, modified with electropositive Fe or Al oxides, can reduce bacteriophages in waters to a greater extent than unmodified ceramic.

Non-monotonic permeability variation during colloidal transport: Governing equations and analytical model

NASA Astrophysics Data System (ADS)

Chequer, L.; Russell, T.; Behr, A.; Genolet, L.; Kowollik, P.; Badalyan, A.; Zeinijahromi, A.; Bedrikovetsky, P.

2018-02-01

Permeability decline associated with the migration of natural reservoir fines impairs the well index of injection and production wells in aquifers and oilfields. In this study, we perform laboratory corefloods using aqueous solutions with different salinities in engineered rocks with different kaolinite content, yielding fines migration and permeability alteration. Unusual permeability growth has been observed at high salinities in rocks with low kaolinite concentrations. This has been attributed to permeability increase during particle detachment and re-attachment of already mobilised fines by electrostatic attraction to the rock in stagnant zones of the porous space. We refine the traditional model for fines migration by adding mathematical expressions for the particle re-attachment rate, particle detachment with delay relative to salinity decrease, and the attached-concentration-dependency of permeability. A one-dimensional flow problem that accounts for those three effects allows for an exact analytical solution. The modified model captures the observed effect of permeability increase at high water salinities in rocks with low kaolinite concentrations. The developed model matches the coreflooding data with high accuracy, and the obtained model coefficients vary within their usual intervals.

Evaluation on expansive performance of the expansive soil using electrical responses

NASA Astrophysics Data System (ADS)

Chu, Ya; Liu, Songyu; Bate, Bate; Xu, Lei

2018-01-01

Light structures, such as highways and railroads, built on expansive soils are prone to damages from the swelling of their underlain soil layers. Considerable amount of research has been conducted to characterize the swelling properties of expansive soils. Current swell characterization models, however, are limited by lack of standardized tests. Electrical methods are non-destructive, and are faster and less expensive than the traditional geotechnical methods. Therefore, geo-electrical methods are attractive for defining soil characteristics, including the swelling behavior. In this study, comprehensive laboratory experiments were undertaken to measure the free swelling and electrical resistivity of the mixtures of commercial kaolinite and bentonite. The electrical conductivity of kaolinite-bentonite mixtures was measured by a self-developed four-electrode soil resistivity box. Increasing the free swelling rate of the kaolinite-bentonite mixtures (0.72 to 1 of porosity of soils samples) led to a reduction in the electrical resistivity and an increase in conductivity. A unique relationship between free swelling rate and normalized surface conductivity was constructed for expensive soils by eliminating influences of porosity and m exponent. Therefore, electrical response measurement can be used to characterize the free swelling rate of expensive soils.

Crude oil polycyclic aromatic hydrocarbons removal via clay-microbe-oil interactions: Effect of acid activated clay minerals.

PubMed

Ugochukwu, Uzochukwu C; Fialips, Claire I

2017-07-01

Acid treatment of clay minerals is known to modify their properties such as increase their surface area and surface acidity, making them suitable as catalysts in many chemical processes. However, the role of these surface properties during biodegradation processes of polycyclic aromatic hydrocarbons (PAHs) is only known for mild acid (0.5 M Hydrochloric acid) treated clays. Four different clay minerals were used for this study: a montmorillonite, a saponite, a palygorskite and a kaolinite. They were treated with 3 M hydrochloric acid to produce acid activated clay minerals. The role of the acid activated montmorillonite, saponite, palygorskite and kaolinite in comparison with the unmodified clay minerals in the removal of PAHs during biodegradation was investigated in microcosm experiments. The microcosm experiments contained micro-organisms, oil, and clays in aqueous medium with a hydrocarbon degrading microorganism community predominantly composed of Alcanivorax spp. Obtained results indicated that acid activated clays and unmodified kaolinite did not enhance the biodegradation of the PAHs whereas unmodified montmorillonite, palygorskite and saponite enhanced their biodegradation. In addition, unmodified palygorskite adsorbed the PAHs significantly due to its unique channel structure. Copyright © 2017 Elsevier Ltd. All rights reserved.

A study of competitive adsorption of organic molecules onto mineral oxides using DRIFTS

DOE PAGES

Joan E. Thomas; Kelley, Michael J.

2009-10-20

In this study, analysis of DRIFTS spectra was used for a quantitative study of competitive adsorption of myristic and salicylic acids onto kaolinite or γ-alumina. Peaks unique to the ring or the chain were selected and single molecule studies used as calibration. Samples were exposed to hexane solution containing equal molecular quantities of each acid. The surface loading of salicylic acid was not influenced by the presence of myristic acid on either mineral but the maximum loading of myristic acid was decreased (46-50%) by salicylic acid. Displacement of myristic acid from {gamma}-alumina, but not kaolinite, was observed when excess salicylicmore » acid remained in solution. A 25% increase in the maximum loading was observed for kaolinite, but not for{gamma}-alumina. On {gamma}-alumina, after a loading of 1 molecule per nm 2, increased exposure resulted in salicylic acid adsorption only, this value is approximately the same for salicylic acid adsorption from aqueous solution or for water washed hexane treated samples. Thus a set of sites for adsorption of either acid is indicated together with other energetically less favorable sites, which can be occupied by salicylic, but not by myristic, acid.« less

ESEEM of industrial silica-bearing powders: reactivity of defects during wet processing in the ceramics production

NASA Astrophysics Data System (ADS)

Romanelli, Maurizio; Di Benedetto, Francesco; Fornaciai, Gabriele; Innocenti, Massimo; Montegrossi, Giordano; Pardi, Luca A.; Zoleo, Alfonso; Capacci, Fabio

2015-05-01

A study is undertaken to ascertain whether changes in the speciation of inorganic radicals are occurring during the ceramic industrial production that involves abundant silica powders as raw material. Industrial dusts were sampled in two ceramic firms, immediately after the wet mixing stage, performed with the aid of a relevant pressure. The dusts were then characterised by means of X-ray diffraction, analysis of the trace elements through chemical methods, granulometry, continuous-wave electron paramagnetic resonance (EPR) and pulsed electron spin echo envelope modulation (ESEEM) spectroscopies. The results of the characterisation point to a relevant change in the speciation of the two samples; namely, a prevailing contribution due to an inorganic radical different from that pertaining to pure quartz is pointed out. The combined interpretation of EPR and ESEEM data suggests the attribution of the main paramagnetic contribution to the A-centre in kaolinite, a constituent that is added to pure quartz at the initial stage of the ceramic production. In one of the two samples, a second weak EPR signal is attributed to the quartz's hAl species. By taking into account the relative quantities of quartz and kaolinite mixed in the two samples, and the relative abundances of the two radical species, we propose that the partial or complete suppression of the hAl species in favour of the A-centre of kaolinite has occurred. Although this change is apparently fostered by the mixture between quartz and another radical-bearing raw material, kaolinite, the suppression of the hAl centre of quartz is ascribed to the role played by the pressure and the wet environment during the industrial mixing procedure. This suppression provides a net change of radical speciation associated with quartz, when this phase is in contact with workers' respiratory system.

Adsorption of bacterial plasmids in pure mineral mixtures

NASA Astrophysics Data System (ADS)

Zhang, L.; Cochran, J. P.; Seaman, J. C.; Parrott, B.

2017-12-01

Microorganisms play an important role in controlling the fate and transport of subsurface contaminants through the direct degradation of organic contaminants to the control of chemical redox conditions that impact the speciation and partitioning of inorganic contaminants. Genes that control these processes, including the relative tolerance associated with direct exposure to toxic contaminants, are found within the bacteria's chromosomal DNA and also within distinct, circular DNA elements called plasmids. Plasmids are mobile genetic elements that can be exchanged with other bacterial species through horizontal gene transfer (HGT). The frequency of HGT in soil is influenced by several factors, with the physicochemical characteristics of soil possibly being a primary factor. Thus, the objective for our research was to determine the movement and persistence of bacterial plasmids within soil. Our current study focuses on batch sorption experiments designed to evaluate the partitioning of bacterial plasmids in idealized mineral mixtures that represent the clay mineralogy of highly weathered soils of the Southeastern US. Specifically, we compared plasmid adsorption among pure goethite, kaolinite, and a mixture of goethite and kaolinite. We also determined the adsorption of plasmids on the above minerals over increasing pH (3 to 10). Our results show that adsorption decreased in the following order: goethite > kaolinite > mixture of goethite and kaolinite. We also found that plasmids adsorption was higher at lower pH levels, with pH 3 having the adsorption maximum. However, at pH 3, DNA denaturing may have occurred, leading to aggregation or precipitation of plasmids on the mineral surfaces. Our study was the first steps in determining the influence of soil properties on plasmid adsorption. Our future goals are to determine the adsorption in other pure minerals and in natural soils.

Geochemical evidences for palaeoclimatic fluctuations at the Triassic-Jurassic boundary: southwestern margin of the Neotethys in the Salt Range, Pakistan

NASA Astrophysics Data System (ADS)

Iqbal, Shahid; Wagreich, Michael; Jan, Irfanullah; Kürschner, Wolfram Michael; Gier, Susanne

2017-04-01

The Triassic-Jurassic boundary interval reveals a change from warm-arid to a warm and humid climate in the Tethyan domain. Sea-level reconstruction records across the European basins during this interval reveal an end-Triassic global regression event and is linked to the Central Atlantic Magmatic Province (CAMP) activity and Pangaea breakup. In the Tethyan Salt Range of Pakistan a succession of Upper Triassic dolomites/green-black mudstones (Kingriali Formation), overlying quartzose sandstone, mudstones, laterites and Lower Jurassic conglomerates/pebbly sandstones (Datta Formation) provides information on the palaeoclimatic evolution of the area. Preliminary palynological results from the mudstones indicate a Rhaetian age for the Kingriali Formation and a Hettangian age for the Datta Formation. X-ray diffraction (XRD) analysis of the mudstones (upper part of the Kingriali Formation) indicates the presence of mainly illite while kaolinite is a minor component. The kaolinite content, a reflection of the advanced stage of chemical weathering and hence warm-humid conditions, increases up-section in the overlying sandstone-mudstone succession. The overlying laterite-bauxite horizons lack illite/smectite and are entirely composed of kaolinite, boehmite and haematite. At places these kaolinite rich horizons are mined in the area (Western Salt Range). The bulk rock geochemistry of the succession confirms a similar trend. The Chemical Index of Alteration (CIA) displays an increasing trend from the Upper Triassic shales (CIA 75-80) through the overlying sandstones/mudstones-laterites to the overlying quartz rich sandstones and mudstones (CIA 90-97). The overall results for the succession reveal an increasing chemical maturity trend (increase in the intensity of chemical weathering) from Rhaetian to Hettangian thereby supporting a change from warm-arid to a warm-humid palaeoclimate, probably extreme greenhouse conditions.

The influence of humic acid and clay content on the transport of polymer-coated iron nanoparticles through sand.

PubMed

Jung, Bahngmi; O'Carroll, Denis; Sleep, Brent

2014-10-15

The introduction of nanoscale zero valent iron (nZVI) into the subsurface has recently received significant attention as a potentially effective method for remediation of source zones of chlorinated solvents present as dense nonaqueous phase liquids (DNAPL). One of the challenges in the deployment of nZVI is to achieve good subsurface nZVI mobility to permit delivery of the nZVI to the target treatment zone. Stabilization of nZVI with various polymers has shown promise for enhancing nZVI subsurface mobility, but the impact of subsurface conditions on nZVI mobility has not been fully explored. In this study, the effect of humic acid and kaolinite on the transport of polymer-stabilized nZVI (carboxylmethyl cellulose-surface modified nZVI, CMC90K-RNIP) in sand was investigated using column experiments. In addition, effects of electrolytes on the stability of CMC90K-RNIP in the presence of humic acid, and the stability of humic acid-coated reactive nanoscale iron particles (HA-RNIP) at various humic acid concentrations were investigated. Humic acid enhanced the mobility of bare RNIP, whereas the transport of CMC90K-RNIP was not significantly affected by humic acid injected as a background solution, except at the highest concentration of 500mg/L. At lower pore water velocity, the effect of humic acid on the transport of CMC90K-RNIP was greater than that at high water velocity. Adding kaolinite up to 2% by weight to the sand column reduced the retention of CMC90K-RNIP, but further increases in kaolinite content (to 5%) did not significantly affect nZVI retention. The impact of kaolinite on nZVI retention was more pronounced at lower pore water velocities. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of solution chemistry on the sunlight inactivation of particles-associated viruses MS2.

PubMed

Wu, Xueyin; Feng, Zhe; Yuan, Baoling; Zhou, Zhenming; Li, Fei; Sun, Wenjie

2018-02-01

The inactivation efficacy of bacteriophage MS2 by simulated sunlight irradiation was investigated to understand the effects of MS2 aggregation and adsorption to particles in solutions with different components. Kaolinite and Microcystis aeruginosa were used as model inorganic and organic particles, respectively. Lower pH and di-valent ions (Ca 2+ ) were main factors on the aggregation and inactivation of MS2. In the presence of both particles, there was no significant impact on the MS2 inactivation efficacy by kaolinite (10-200mM) or Microcystis aeruginosa (10 2 -10 5 Cells/mL) in 1mM NaCl at pH 7. However at lower pH 3, MS2 aggregates formed in the particle-free and kaolinite-containing solutions, caused lower inactivation since the outer viruses of aggregation protect the inner viruses. In addition, more MS2 adsorbed on Microcystis aeruginosa at lower pH (3 and 4). Microcystis aeruginosa would act as a potential photosensitizer for ROS production to inactivate the adsorbed MS2, since extracellular organic matter (EOM) of Microcystis aeruginosa was detected in this study, which has been reported to produce ROS under solar irradiation. At pH 7, Na + had no effect on the inactivation of MS2, because MS2 was stable and dispersed even at 200mM Na + . MS2 aggregated and adsorbed on particles even at 10mM Ca 2+ and led to lower inactivation. Kaolinite cannot offer enough protection to adsorbed MS2 as aggregation and Microcystis aeruginosa acts as potential photosensitizer to produce ROS and inactivate the adsorbed MS2 at high concentration of Ca 2+ . In particle-free solution, SRNOM inhibited MS2 inactivation by shielding the sunlight and coating MS2 to increase its survival. Copyright © 2017 Elsevier B.V. All rights reserved.

A preliminary study of older hot spring alteration in Sevenmile Hole, Grand Canyon of the Yellowstone River, Yellowstone Caldera, Wyoming

USGS Publications Warehouse

Larson, Peter B.; Phillips, Allison; John, David A.; Cosca, Michael A.; Pritchard, Chad; Andersen, Allen; Manion, Jennifer

2009-01-01

Erosion in the Grand Canyon of the Yellowstone River, Yellowstone Caldera (640 ka), Wyoming, has exposed a cross section of older hydrothermal alteration in the canyon walls. The altered outcrops of the post-collapse tuff of Sulphur Creek (480 ka) extend from the canyon rim to more than 300 m beneath it. The hydrothermal minerals are zoned, with an advanced argillic alteration consisting of an association of quartz (opal) + kaolinite ± alunite ± dickite, and an argillic or potassic alteration association with quartz + illite ± adularia. Disseminated fine-grained pyrite or marcasite is ubiquitous in both alteration types. These alteration associations are characteristic products of shallow volcanic epithermal environments. The contact between the two alteration types is about 100 m beneath the rim. By analogy to other active geothermal systems including active hydrothermal springs in the Yellowstone Caldera, the transition from kaolinite to illite occurred at temperatures in the range 150 to 170 °C. An 40Ar/39Ar age on alunite of 154,000 ± 16,000 years suggests that hydrothermal activity has been ongoing since at least that time. A northwest-trending linear array of extinct and active hot spring centers in the Sevenmile Hole area implies a deeper structural control for the upflowing hydrothermal fluids. We interpret this deeper structure to be the Yellowstone Caldera ring fault that is covered by the younger tuff of Sulphur Creek. The Sevenmile Hole altered area lies at the eastern end of a band of hydrothermal centers that may mark the buried extension of the Yellowstone Caldera ring fault across the northern part of the Caldera.

Compositional controls on early diagenetic pathways in fine-grained sedimentary rocks: Implications for predicting unconventional reservoir attributes of mudstones

USGS Publications Warehouse

Keller, Margaret A.; Macquaker, Joe H.S.; Taylor, Kevin G.; Polya, David

2014-01-01

Diagenesis significantly impacts mudstone lithofacies. Processes operating to control diagenetic pathways in mudstones are poorly known compared to analogous processes occurring in other sedimentary rocks. Selected organic-carbon-rich mudstones, from the Kimmeridge Clay and Monterey Formations, have been investigated to determine how varying starting compositions influence diagenesis.The sampled Kimmeridge Clay Formation mudstones are organized into thin homogenous beds, composed mainly of siliciclastic detritus, with some constituents derived from water-column production (e.g., coccoliths, S-depleted type-II kerogen, as much as 52.6% total organic carbon [TOC]) and others from diagenesis (e.g., pyrite, carbonate, and kaolinite). The sampled Monterey Formation mudstones are organized into thin beds that exhibit pelleted wavy lamination, and are predominantly composed of production-derived components including diatoms, coccoliths, and foraminifera, in addition to type-IIS kerogen (as much as 16.5% TOC), and apatite and silica cements.During early burial of the studied Kimmeridge Clay Formation mudstones, the availability of detrital Fe(III) and reactive clay minerals caused carbonate- and silicate-buffering reactions to operate effectively and the pore waters to be Fe(II) rich. These conditions led to pyrite, iron-poor carbonates, and kaolinite cements precipitating, preserved organic carbon being S-depleted, and sweet hydrocarbons being generated. In contrast, during the diagenesis of the sampled Monterey Formation mudstones, sulfide oxidation, coupled with opal dissolution and the reduced availability of both Fe(III) and reactive siliciclastic detritus, meant that the pore waters were poorly buffered and locally acidic. These conditions resulted in local carbonate dissolution, apatite and silica cements precipitation, natural kerogen sulfurization, and sour hydrocarbons generation.Differences in mud composition at deposition significantly influence subsequent

Preliminary analysis of shuttle multispectral radiometer data for Southern Egypt

USGS Publications Warehouse

Rowan, L.C.; Goetz, A.F.H.; Kingston, M.J.

1983-01-01

The Shuttle Multispectral Infrared Radiometer (SMIRR) is a spectroradiometer covering the region from 0.5 to 2.5 ??m in 10 channels that acquired data from spots 100 m in diameter along the subspacecraft ground track. It was flown aboard the second flight of the space shuttle Columbia, November 12-14, 1981. Data collected during orbit 16 over southern Egypt show that carbonate rocks, kaolinite, and possibly montmorillonite can be identified by their SMIRR spectral signatures and limited knowledge of the lithologic units present. Detailed analysis of SMIRR data for this area indicates that calcite, kaolinite, and montmorillonite rocks give rise to absorption features that result in characteristic 10 channel spectra. ?? 1983.

The Use 0f AVIRIS Imagery To Assess Clay Mineralogy And Debris-Flow Potential In Cataract Canyon, Utah: A Preliminary Report

NASA Technical Reports Server (NTRS)

Rudd, Lawrence; Merenyi, Erzsebet

2004-01-01

Worldwide debris flows destroy property and take human lives every year (Costa, 1984). As a result of extensive property damage and loss of life there is a pressing need to go beyond just describing the nature and extent of debris flows as they occur. Most of the research into debris-flow initiation has centered on rainfall, slope angle, and existing debris-flow deposits (Costa and Wieczorek, 1987). The factor of source lithology has been recently addressed by studies in the sedimentary terranes of Grand Canyon (Webb et al., 1996; Griffiths et al., 1996) and on the Colorado Plateau as a whole.3 On the Colorado Plateau shales dominated by kaolinite and illite clays are significantly more likely to be recent producers of debris-flows than are shales in which smectite clays dominate.3 Establishing the location of shales and colluvial deposits containing kaolinite and illite clays in sedimentary terranes on the Colorado Plateau is essential to predicting where debris flows are likely to occur. AVIRIS imagery can be used to distinguish between types of clay minerals (Chabrillat et al., 2001), providing the basis for surface-materials maps. The ultimate product of this study will be a model that can be used to estimate the debris-flow hazard in Cataract Canyon, Utah. This model will be based on GIS overlay analysis of debris-flow initiation factor maps, including surface-materials maps derived from AVIRIS data.

Interactions of EPS with soil minerals: A combination study by ITC and CLSM.

PubMed

Lin, Di; Ma, Wenting; Jin, Zhaoxia; Wang, Yixuan; Huang, Qiaoyun; Cai, Peng

2016-02-01

The adsorption of extracellular polymeric substances (EPS) from Pseudomonas putida on montmorillonite, kaolinite and goethite was investigated as a function of pH using batch studies coupled with confocal laser scanning microscopy (CLSM) and isothermal titration calorimetry (ITC). Characterization by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy showed that the extracted EPS contained carboxyl, phosphoryl, amino, and hydroxyl on functional groups as well as polysaccharides, protein and nucleic acid on components. The mass fraction of EPS adsorption on minerals decreased with the final pH increased from 3.0 to 9.0. The mass fraction of EPS-N adsorption varied with pH values and was higher than that of EPS-C or EPS-P on montmorillonite and kaolinite, while the mass fraction of EPS-P adsorption was the highest on goethite. CLSM results further demonstrated that proteins were predominantly distributed on the montmorillonite and kaolinite surfaces, while nucleic acids were mainly on the goethite surface. ITC results revealed that the adsorption process in all mineral systems was exothermic, and pH altered the heat effect of EPS-mineral reactions. The data obtained in this study would facilitate a better understanding of the adsorption mechanisms of EPS on minerals. Copyright © 2015 Elsevier B.V. All rights reserved.

Interference of 1:1 and 2:1 layered phyllosilicates as excipients with ranitidine.

PubMed

Li, Zhaohui; Fitzgerald, Nicole M; Albert, Zachary; Jiang, Wei-Teh

2016-04-01

As natural ingredients and excipients, kaolinite and talc were frequently studied for their interactions with drugs in pharmaceutical formulations. In this study, the uptake of ranitidine (RT) on these two minerals was studied under different physic-chemical conditions and the mechanism of RT uptake on these two minerals contrasted. Although the thermodynamic and kinetic RT uptake on these two minerals was similar and the RT uptake on both minerals were limited to the external surfaces only, drastic difference in RT uptake was found under different equilibrium solution pH and ionic strength conditions. As cation exchange process was strongly affected by solution pH and ionic strength, the RT uptake on kaolinite was dominated by cation exchange and electrostatic interactions, while the RT uptake on talc was more controlled by inter- and intra- molecular hydrogen bonding interactions. For kaolinite, the limiting factor for RT uptake was the specific surface area due to monolayer RT adsorption. In contract, multilayer RT uptake was found on talc surfaces. No matter which mechanism dominated RT uptake on these minerals, the interaction should not be neglected in pharmaceutical formulations should these minerals be used as additives and/or excipients. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of organic matter on CO(2) hydrate phase equilibrium in phyllosilicate suspensions.

PubMed

Park, Taehyung; Kyung, Daeseung; Lee, Woojin

2014-06-17

In this study, we examined various CO2 hydrate phase equilibria under diverse, heterogeneous conditions, to provide basic knowledge for successful ocean CO2 sequestration in offshore marine sediments. We investigated the effect of geochemical factors on CO2 hydrate phase equilibrium. The three-phase (liquid-hydrate-vapor) equilibrium of CO2 hydrate in the presence of (i) organic matter (glycine, glucose, and urea), (ii) phyllosilicates [illite, kaolinite, and Na-montmorillonite (Na-MMT)], and (iii) mixtures of them was measured in the ranges of 274.5-277.0 K and 14-22 bar. Organic matter inhibited the phase equilibrium of CO2 hydrate by association with water molecules. The inhibition effect decreased in the order: urea < glycine < glucose. Illite and kaolinite (unexpandable clays) barely affected the CO2 hydrate phase equilibrium, while Na-MMT (expandable clay) affected the phase equilibrium because of its interlayer cations. The CO2 hydrate equilibrium conditions, in the illite and kaolinite suspensions with organic matter, were very similar to those in the aqueous organic matter solutions. However, the equilibrium condition in the Na-MMT suspension with organic matter changed because of reduction of its inhibition effect by intercalated organic matter associated with cations in the Na-MMT interlayer.

Fault gouge rheology under confined, high-velocity conditions

NASA Astrophysics Data System (ADS)

Reches, Z.; Madden, A. S.; Chen, X.

2012-12-01

We recently developed the experimental capability to investigate the shear properties of fine-grain gouge under confined conditions and high-velocity. The experimental system includes a rotary apparatus that can apply large displacements of tens of meters, slip velocity of 0.001- 2.0 m/s, and normal stress of 35 MPa (Reches and Lockner, 2010). The key new component is a Confined ROtary Cell (CROC) that can shear a gouge layer either dry or under pore-pressure. The pore pressure is controlled by two syringe pumps. CROC includes a ring-shape gouge chamber of 62.5 mm inner diameter, 81.25 mm outer diameter, and up to 3 mm thick gouge sample. The lower, rotating part of CROC contains the sample chamber, and the upper, stationary part includes the loading, hollow cylinder and setting for temperature, and dilation measurements, and pore-pressure control. Each side of the gouge chamber has two pairs of industrial, spring-energized, self-lubricating, teflon-graphite seals, built for particle media and can work at temperature up to 250 ded C. The space between each of the two sets of seals is pressurized by nitrogen. This design generates 'zero-differential pressure' on the inner seal (which is in contact with the gouge powder), and prevents gouge leaks. For the preliminary dry experiments, we used ~2.0 mm thick layers of room-dry kaolinite powder. Total displacements were on the order of meters and normal stress up to 4 MPa. The initial shear was accommodated by multiple internal slip surfaces within the kaolinite layer accommodated as oriented Riedel shear structures. Later, the shear was localized within a thin, plate-parallel Y-surface. The kaolinite layer was compacted at a quasi-asymptotic rate, and displayed a steady-state friction coefficient of ~ 0.5 with no clear dependence on slip velocity up to 0.15 m/s. Further experiments with loose quartz sand (grain size ~ 125 micron) included both dry runs and pore-pressure (distilled water) controlled runs. The sand was

Irreversibility of 2,4-Dichlorophenoxyacetic Acid Sorption onto a Volcanic Ash Soil

NASA Astrophysics Data System (ADS)

Mon, E.; Kawamoto, K.; Komatsu, T.; Moldrup, P.

2008-12-01

Pesticide sorption and desorption in soils are key processes governing fate and transport of pesticides in the soil environment. The irreversibility (or hysteresis) in the processes of pesticide sorption and desorption needs to be known to accurately predict behavior of pesticides in soil systems. 2,4-dichlorophenoxyacetic acid (2,4-D) is a widely used pesticide in agriculture fields. However, only few studies of 2,4-D adsorption onto Andosols (volcanic ash soils) have been published, and the knowledge of 2,4-D desorption onto Andosols is very limited. In this study, a volcanic ash soil sampled from a pasture site in Nishi-Tokyo, Japan was used as a sorbent in order to investigate the irreversibility of 2,4-D sorption. For comparison, a pure clay mineral (kaolinite) obtained from Clay Science Society of Japan (CSSJ) was also used. 2,4-D solutions with three concentrations (0.011, 0.022 and 0.045 mmol/L) were prepared in artificial rain water (ARW= 0.085mM NaCl + 0.015mM CaCl2) to simulate field conditions. To prepare the sample solutions, the solid mass/liquid volume ratio of 1:10 was used for both sorbents (volcanic ash soil and kaolinite). The experiments were conducted in triplicate using a batch method under different pH conditions to examine the effect of pH. Desorption was measured during a equilibration procedure: After removal of 7 mL of supernatant in the sorption step, 7 mL of ARW excluding 2,4-D was added to the sample solution after which, it was equilibrated and centrifuged. The procedure was performed sequentially three or four times to obtain a desorption isotherm. Sorption and desorption generally followed Freundlich isotherms. The results showed markedly effects of pH on 2,4-D sorption and desorption in both the soil and kaolinite, with the percentage of sorption increasing with decreasing pH whereas the percentage of desorption decreased. There was a larger adsorption-desorption hysteresis in the volcanic ash soil as compared to kaolinite

Using organic matter to increase soil fertility in Burundi: potentials and limitations

NASA Astrophysics Data System (ADS)

Kaboneka, Salvator

2015-04-01

Agriculture production in Burundi is dominated by small scale farmers (0.5 ha/household) who have only very limited access to mineral inputs. In the past, farmers have relied on fallow practices combined with farm yard manures to maintain and improve soil fertility. However, due to the high population growth and high population density (370/km²), fallow practices are nowadays no longer feasible, animal manures cannot be produced in sufficient quantities to maintain soil productivity and food insecurity has become a quasi permanent reality. Most Burundian soils are characterized by 1:1 types of clay minerals (kaolinite) and are acidic in nature. Such soils are of very low cation exchange capacity (CEC). To compare the effect of % clays and % organic matter (% C), correlations tests have been conducted between the two parameters and the CEC. It was found that in high altitude kaolinitic and acidic soils, CEC was highly correlated to % C and less correlated to % clay, suggesting that organic matter could play an important role in improving fertility and productivity of these soils. Based on these findings, additional studies have been conducted to evaluate the fertilizer and soil amendment values of animal manures (cattle, goat, chicken), and leguminous (Calliandra calothyrsus, Gliricidia sepium, Senna simea, Senna spectabilis) and non-leguminous (Tithonia diversifolia) foliar biomass. It was observed that chicken manure significantly reduces Al3+ levels in acidic soils, while Tithonia diversifolia outperforms in nutrient releases compared to the commonly known leguminous agroforestry shrubs and trees indicated above. Although the above mentioned organic sources can contribute to the soil nutrients supply, the quantities potentially available on farm are generally small. The only solution is to supplement these organic sources with other organic sources (compost, organic household waste), chemical fertilizers and mineral amendments (lime) to achieve Integrated Soil

Lithologic Control on Secondary Clay Mineral Formation in the Valles Caldera, New Mexico

NASA Astrophysics Data System (ADS)

Caylor, E.; Rasmussen, C.; Dhakal, P.

2015-12-01

Understanding the transformation of rock to soil is central to landscape evolution and ecosystem function. The objective of this study was to examine controls on secondary mineral formation in a forested catchment in the Catalina-Jemez CZO. We hypothesized landscape position controls the type of secondary minerals formed in that well-drained hillslopes favor Si-poor secondary phases such as kaolinite, whereas poorly drained portions of the landscape that collect solutes from surrounding areas favor formation of Si-rich secondary phases such as smectite. The study focused on a catchment in Valles Caldera in northern New Mexico where soils are derived from a mix of rhyolitic volcanic material, vegetation includes a mixed conifer forest, and climate is characterized by a mean annual precipitation of ~800 mm yr-1 and mean annual temperature of 4.5°C. Soils were collected at the soil-saprolite boundary from three landscape positions, classified as well drained hillslope, poorly drained convergent area, and poorly drained hill slope. Clay fractions were isolated and analyzed using a combination of quantitative and qualitative x-ray diffraction (XRD) analyses and thermal analysis. Quantitative XRD of random powder mounts indicated the presence of both primary phases such as quartz, and alkali and plagioclase feldspars, and secondary phases that include illite, Fe-oxyhydroxides including both goethite and hematite, kaolinite, and smectite. The clay fractions were dominated by smectite ranging from 36-42%, illite ranging from 21-35%, and kaolinite ranging from 1-8%. Qualitative XRD of oriented mounts confirmed the presence of smectite in all samples, with varying degrees of interlayering and interstratification. In contrast to our hypothesis, results indicated that secondary mineral assemblage was not strongly controlled by landscape position, but rather varied with underlying variation in lithology. The catchment is underlain by a combination of porphorytic rhyolite and

Effect of the environment on the hydrochemical characteristics of an alluvial aquifer following an exceptional multiyear drought (Mediterranean Seashore, Hérault, France): Part II—Climatology and agronomy

NASA Astrophysics Data System (ADS)

Grillot, Jean-Claude; Chaffaut, Isabelle; Razack, Moumtaz

1988-04-01

The hydrochemical evolution of an alluvial groundwater located along the Mediterranean seashore is analyzed with respect to its agricultural and climatic environment, including degree of saturation of the soil; types of cultures, chemical fertilizers and phytosanitary treatments; selective irrigations of the cultivated areas; precipitations. It is shown that the environmental effect on the groundwater's vulnerability depends on two groups of factors: 1. Transfers from surface to groundwater of nitrates, chlorides, sulfates, and potassium, which are governed by: (a) the climatic conditions before the agricultural activities begin, (b) the kinds of agricultural activities and their distribution in time with respect to a given climatic context. Phenomena of retention of and/or rapid diffusion are related to the sedimentary heterogeneities of the reservoir and to the differences of temperatures between irrigation waters and precipitations. 2. Cationic exchanges related to the presence of clays of Montmorillonite-Kaolinite type.

Survey Report on Cooper River, S.C. (Shoaling in Charleston Harbor), Appendix A, Supplement 3. Special Geological Investigations Utilizing Diagnostic Minerals.

DTIC Science & Technology

CLAY, COASTAL REGIONS, CYCLES, DELTAS, DEPOSITION, DIAGNOSIS(GENERAL), FINES, FLOW, GEOLOGY, GEOMORPHOLOGY, KAOLINITE , MATHEMATICAL MODELS, MINERALS...MODELS, MONTMORILLONITE , PARAMETERS, PETROGRAPHY, PROCESSING, RATIOS, RESIDUALS, RESPONSE, RIVERS, SALINITY, SAMPLING, SAND, SCHIST, SEDIMENTS

Effect of organic matter properties, clay mineral type and thermal maturity on gas adsorption in organic-rich shale systems

USGS Publications Warehouse

Zhang, Tongwei; Ellis, Geoffrey S.; Ruppel, Stephen C.; Milliken, Kitty; Lewan, Mike; Sun, Xun; Baez, Luis; Beeney, Ken; Sonnenberg, Steve

2013-01-01

A series of CH4 adsorption experiments on natural organic-rich shales, isolated kerogen, clay-rich rocks, and artificially matured Woodford Shale samples were conducted under dry conditions. Our results indicate that physisorption is a dominant process for CH4 sorption, both on organic-rich shales and clay minerals. The Brunauer–Emmett–Teller (BET) surface area of the investigated samples is linearly correlated with the CH4 sorption capacity in both organic-rich shales and clay-rich rocks. The presence of organic matter is a primary control on gas adsorption in shale-gas systems, and the gas-sorption capacity is determined by total organic carbon (TOC) content, organic-matter type, and thermal maturity. A large number of nanopores, in the 2–50 nm size range, were created during organic-matter thermal decomposition, and they significantly contributed to the surface area. Consequently, methane-sorption capacity increases with increasing thermal maturity due to the presence of nanopores produced during organic-matter decomposition. Furthermore, CH4 sorption on clay minerals is mainly controlled by the type of clay mineral present. In terms of relative CH4 sorption capacity: montmorillonite ≫ illite – smectite mixed layer > kaolinite > chlorite > illite. The effect of rock properties (organic matter content, type, maturity, and clay minerals) on CH4 adsorption can be quantified with the heat of adsorption and the standard entropy, which are determined from adsorption isotherms at different temperatures. For clay-mineral rich rocks, the heat of adsorption (q) ranges from 9.4 to 16.6 kJ/mol. These values are considerably smaller than those for CH4 adsorption on kerogen (21.9–28 kJ/mol) and organic-rich shales (15.1–18.4 kJ/mol). The standard entropy (Δs°) ranges from -64.8 to -79.5 J/mol/K for clay minerals, -68.1 to -111.3 J/mol/K for kerogen, and -76.0 to -84.6 J/mol/K for organic-rich shales. The affinity of CH4 molecules for sorption on organic matter

Heterogeneous precipitation of silver nanoparticles on kaolinite plates

NASA Astrophysics Data System (ADS)

Cabal, B.; Torrecillas, R.; Malpartida, F.; Moya, J. S.

2010-11-01

Two different methods to obtain silver nanoparticles supported on kaolin crystals have been performed: the first one followed a thermal reduction and the second one a chemical reduction. In both cases, the silver nanoparticles with two different average particles size (ca.12 and 30 nm) were perfectly isolated and attached to the surface of the kaolin plates. The silver nanoparticles were localized mainly at the edge of the single crystal plates, the hydroxyl groups being the main centres of adsorption. The samples were fully characterized by XRD, UV-vis spectroscopy and TEM. The antimicrobial benefits of the composites were evaluated as antibacterial against common Gram-positive and Gram-negative bacteria, and antifungal activity against yeast. The results indicated a high antimicrobial activity for Escherichia coli JM 110 and Micrococcus luteus, while being inactive against yeast under our experimental conditions. The chemical analysis of Ag in the fermentation broths show that only a small portion of metal (<9 ppm) is released from the kaolin/metakaolin particles. Therefore, the risk of toxicity due to a high concentration of metal in the medium is minimized.

Mineralogical, crystallographic and morphological characteristics of natural kaolins from the Ivory Coast (West Africa)

NASA Astrophysics Data System (ADS)

Sei, J.; Morato, F.; Kra, G.; Staunton, S.; Quiquampoix, H.; Jumas, J. C.; Olivier-Fourcade, J.

2006-10-01

Thirteen clay samples from four deposits in the Ivory Coast (West Africa) were studied using X-ray diffraction, thermogravimetric analysis and chemical analysis. Mineralogical, crystallographic and morphological characteristics of these samples are given. Kaolinite is the principal mineral but other minerals are present in small quantities: illite, quartz, anatase and iron oxides (oxides and oxyhydroxides). The crystallographic, morphological and surface characteristics are influenced by the presence of these impurities. In particular, the presence of iron oxides was associated with reduced structural ordering and thermal stability of kaolinite and increased specific surface area. These clays could be used in the ceramics industry to make tiles and bricks, and also in agronomy as supports for chemical fertilizers or for environmental protection by immobilising potentially toxic waste products.

Raman spectroscopic analysis of real samples: Brazilian bauxite mineralogy

NASA Astrophysics Data System (ADS)

Faulstich, Fabiano Richard Leite; Castro, Harlem V.; de Oliveira, Luiz Fernando Cappa; Neumann, Reiner

2011-10-01

In this investigation, Raman spectroscopy with 1064 and 632.8 nm excitation was used to investigate real mineral samples of bauxite ore from mines of Northern Brazil, together with Raman mapping and X-rays diffraction. The obtained results show clearly that the use of microRaman spectroscopy is a powerful tool for the identification of all the minerals usually found in bauxites: gibbsite, kaolinite, goethite, hematite, anatase and quartz. Bulk samples can also be analysed, and FT-Raman is more adequate due to better signal-to-noise ratio and representativity, although not efficient for kaolinite. The identification of fingerprinting vibrations for all the minerals allows the acquisition of Raman-based chemical maps, potentially powerful tools for process mineralogy applied to bauxite ores.

Modified clay sorbents

DOEpatents

Fogler, H. Scott; Srinivasan, Keeran R.

1990-01-01

A novel modified clay sorbent and method of treating industrial effluents to remove trace pollutants, such as dioxins, biphenyls, and polyaromatics such as benzo(a)pyrene and pentachlorophenol. The novel clay sorbent has a composite structure in which the interlayer space of an expandable clay, such as smectite, is filled with polyvalent or multivalent inorganic cations which forces weaker surfactant cations to locate on the surface of the clay in such an orientation that the resulting composite is hydrophilic in nature. A specific example is cetylpyridinium-hydroxy aluminum-montmorillonite. In certain embodiments, a non-expanding clay, such as kaolinite, is used and surfactant cations are necessarily located on an external surface of the clay. A specific example is cetylpyridinium-kaolinite.

Origin and evolution of mineralizing fluids and exploration of the Cerro Quema Au-Cu deposit (Azuero Peninsula, Panama) from a fluid inclusion and stable isotope perspective

USGS Publications Warehouse

Corral, Isaac; Cardellach, Esteve; Corbella, Merce; Canals, Angels; Griera, Albert; Gomez-Gras, David; Johnson, Craig A.

2017-01-01

�D from − 103.3 to − 35.2‰, whereas the δ18O of dickite varies between 12.7 and 16.3‰ and δD from − 44 to − 30. Based on δ18O and δD, two types of kaolinite/dickite can be distinguished, a supergene type and a hypogene type. Combined, the analytical data indicate that the Cerro Quema deposit formed from magmatic-hydrothermal fluids derived from a porphyry copper-like intrusion located at depth likely towards the east of the deposit. The combination of stable isotope geochemistry and fluid inclusion analysis may provide useful exploration vectors for porphyry copper targets in the high sulfidation/lithocap environment.

Evidence of cyclic climatic changes recorded in clay mineral assemblages from a continental Paleocene-Eocene sequence, northwestern Argentina

NASA Astrophysics Data System (ADS)

Do Campo, Margarita; Bauluz, Blanca; del Papa, Cecilia; White, Timothy; Yuste, Alfonso; Mayayo, Maria Jose

2018-06-01

The continental Paleocene-Eocene sequence investigated in this study belongs to the Salta Group, deposited in an intracontinental rift, the Salta Basin (NW Argentina), that evolved from the lower Cretaceous to the middle Paleogene, and is subdivided into the Pirgua, the Balbuena and the Santa Barbara Subgroups. The Maíz Gordo Formation (200 m thick) is the middle unit of the Santa Bárbara Subgroup, deposited during late post-rift sedimentation. We studied the mineralogy of fine-grained horizons of this formation by X-ray diffraction and Scanning Electron Microscopy (SEM) in order to examine the connection between vertical changes in clay mineralogy in alluvial sediments and paleosols, and global paleoclimatic changes registered during the Paleogene. Paleosols vary from calcic vertisols in the lowermost levels, to inseptisols and gleysols in intermediate positions, to gleyed oxisols in the upper section, indicating increased chemical weathering through time. Clay mineral relative abundances vary with a general increase in kaolinite content from bottom to top. However, at one site there are significant variations in kaolinite/muscovite (Kln/Ms) that define five cycles of kaolinite abundance and Kln/Ms. that indicate cyclic patterns of paleoprecipitation and paleotemperature. These are interpreted as several short-lived hyperthermals during the Paleocene-early Eocene in the Southern Hemisphere, which correlate with well-established episodes of warmth documented from the Northern Hemisphere.

Geological and technological characterization of the Late Jurassic-Early Cretaceous clay deposits (Jebel Ammar, northeastern Tunisia) for ceramic industry

NASA Astrophysics Data System (ADS)

Ben M'barek-Jemaï, Moufida; Sdiri, Ali; Ben Salah, Imed; Ben Aissa, Lassaad; Bouaziz, Samir; Duplay, Joelle

2017-05-01

Late Jurassic-Lower Cretaceous clays of the Jebel Ammar study site were used as raw materials for potential applications in ceramic industry. Physico-chemical characterization of the collected samples was performed using atomic absorption spectroscopy, X-ray diffraction, thermogravimetry and dilatometry (Bugot's curve). Geotechnical study was also undertaken by the assessment of plasticity and liquidity limits. It was found that high concentrations of silica, alumina with SiO2/Al2O3 ratio characterized the studied clays; its high amounts of CaO and Fe2O3 in the Late Jurassic clays indicated their calcareous nature. In addition, technological tests indicated moderate to low plasticity values for the Late Jurassic and Lower Cretaceous clays, respectively. Clay fraction (<2 μm) reached 50% of the natural clay in some cases. Mineralogical analysis showed that Jurassic clays were dominated by smectite, illite and kaolinite, as clay mineral species; calcite was the main associated mineral. Lower Cretaceous clays were mainly composed of abundant illite accompanied by well-crystallized smectite and kaolinite. Kaolinite gradually increased upwards, reaching 70% of the total clay fraction (i.e. <2 μm). Quartz, calcite and feldspar were the main non-clay minerals. Based on these analyses, the clays meet technological requirements that would allow their use in the ceramic industry and for the manufacturing of ceramic tiles.

Spectral properties and ASTER-based alteration mapping of Masahim volcano facies, SE Iran

NASA Astrophysics Data System (ADS)

Tayebi, Mohammad H.; Tangestani, Majid H.; Vincent, Robert K.; Neal, Devin

2014-10-01

This study applies Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data and the Mixture Tuned Matched Filtering (MTMF) algorithm to map the sub-pixel distribution of alteration minerals associated with the Masahim volcano, SE Iran for understanding the spatial relationship between alteration minerals and volcano facies. Investigations of the alteration mineralogy were conducted using field-spectroscopy, X-ray diffraction (XRD) analysis and ASTER Short Wave Infrared (SWIR) spectral data. In order to spectrally characterize the stratovolcano deposits, lithological units and alteration minerals, the volcano was divided into three facies: the Central, Proximal, and Medial-distal facies. The reflectance spectra of rock samples show absorption features of a number of minerals including white mica, kaolinite, montmorillonite, illite, goethite, hematite, jarosite, opal, and chlorite. The end-members of key alteration minerals including sericite (phyllic zone), kaolinite (argillic zone) and chlorite (propylitic zone) were extracted from imagery using the Pixel Purity Index (PPI) method and were used to map alteration minerals. Accuracy assessment through field observations was used to verify the fraction maps. The results showed that most prominent altered rocks situated at the central facies of volcano. The alteration minerals were discriminated with the coefficient of determination (R2) of 0.74, 0.81, and 0.68 for kaolinite, sericite, and chlorite, respectively. The results of this study have the potential to refine the map of alteration zones in the Masahim volcano.

A Developed Spectral Identification Tree for Mineral Mapping using Hyperspectral Data

NASA Astrophysics Data System (ADS)

Gan, Fuping; Wang, Runsheng; Yan, Bokun; Shang, Kun

2016-04-01

The relationship between the spectral features and the composition of minerals are the basis of mineral identification using hyperspectral data. The reflectance spectrum of minerals results from the systematic combination of several modes of interaction between electromagnetic energy and mineral particles in the form of reflection and absorption. Minerals tend to have absorbing features at specific wavelengths with a characteristic shape, which can be used as diagnostic indicators for identification. The spectral identification tree (SIT) method for mineral identification is developed in our research to map minerals accurately and applied in some typical mineral deposits in China. The SIT method is based on the diagnostic absorption features of minerals through comparing and statistically analyzing characteristic spectral data of minerals. We establish several levels of identification rules for the type, group and species of minerals using IF-THEN rule according to the spectral identification criteria so that the developed SIT can be further used to map minerals at different levels of detail from mineral type to mineral species. Identifiable minerals can be grouped into six types: Fe2+-bearing, Fe3+-bearing, Mn2+-bearing, Al-OH-bearing, Mg-OH-bearing and carbonate minerals. Each type can be further divided into several mineral groups. Each group contains several mineral species or specific minerals. A mineral spectral series, therefore, can be constructed as "type-group-species-specific mineral (mineral variety)" for mineral spectral identification. It is noted that the mineral classification is based mainly on spectral reflectance characteristics of minerals which may not be consistent with the classification in mineralogy. We applied the developed SIT method to the datasets acquired at the Eastern Tianshan Mountains of Xinjiang (HyMap data) and the Qulong district of Xizang (Hyperion data). In Xinjiang, the two major classes of Al-OH and Mg-OH minerals were

Moving beyond Type I and Type II neuron types.

PubMed

Skinner, Frances K

2013-01-01

In 1948, Hodgkin delineated different classes of axonal firing.  This has been mathematically translated allowing insight and understanding to emerge.  As such, the terminology of 'Type I' and 'Type II' neurons is commonplace in the Neuroscience literature today.  Theoretical insights have helped us realize that, for example, network synchronization depends on whether neurons are Type I or Type II.  Mathematical models are precise with analyses (considering Type I/II aspects), but experimentally, the distinction can be less clear.  On the other hand, experiments are becoming more sophisticated in terms of distinguishing and manipulating particular cell types but are limited in terms of being able to consider network aspects simultaneously.   Although there is much work going on mathematically and experimentally, in my opinion it is becoming common that models are either superficially linked with experiment or not described in enough detail to appreciate the biological context.  Overall, we all suffer in terms of impeding our understanding of brain networks and applying our understanding to neurological disease.  I suggest that more modelers become familiar with experimental details and that more experimentalists appreciate modeling assumptions. In other words, we need to move beyond our comfort zones.

Evidence of Phyllosilicate in Wooly Patch+: An Altered Rock Encountered on the Spirit Rover Traverse

NASA Technical Reports Server (NTRS)

Wang, Alian; Haskin, Larry A.; Korotev, Randy L.; Jolliff, Brad L.; deSouza, Paulo, Jr.; Kusack, Alastair G.

2005-01-01

In the course of examining rocks along the traverse of the Spirit rover toward the Columbia Hills [1, 9], we noticed that the chemistry of a rock named "Wooly Patch" was neither basaltic as the rocks near the landing site [8] nor slightly altered basalt inferred from regolith in plains trenches [10]. The major cation ratios appear to match those of phyllosilicates [11]. The presence of phyllosilicate minerals on Mars has been predicted [12]; reasons for the rarity or absence of phyllosilicates have also been discussed [13]. We have thus done as detailed an analysis of Wooly Patch as the data enable, which suggests phyllosilicates of kaolinite, serpentine, and chlorite types, plus some feldspar and pyroxene are prime candidates to constitute Wooly Patch.

Diagenesis and reservoir quality of Bhuban sandstones (Neogene), Titas Gas Field, Bengal Basin, Bangladesh

NASA Astrophysics Data System (ADS)

Aminul Islam, M.

2009-06-01

This study deals with the diagenesis and reservoir quality of sandstones of the Bhuban Formation located at the Titas Gas Field of Bengal Basin. Petrographic study including XRD, CL, SEM and BSE image analysis and quantitative determination of reservoir properties were carried out for this study. The sandstones are fine to medium-grained, moderately well to well sorted subfeldspathic arenites with subordinate feldspathic and lithic arenites. The diagenetic processes include clay infiltration, compaction and cementation (quartz overgrowth, chlorite, kaolinite, calcite and minor amount of pyrite, dolomite and K-feldspar overgrowth). Quartz is the dominant pore occluding cement and generally occurred as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Pressure solution derived from grain contact is the main contributor of quartz overgrowths. Chlorite occurs as pore-lining and pore filling cement. In some cases, chlorite helps to retain porosity by preventing quartz overgrowth. In some restricted depth interval, pore-occlusion by calcite cement is very much intense. Kaolinite locally developed as vermiform and accelerated the minor porosity loss due to pore-occlusion. Kaolinite/chlorite enhances ineffective microporosity. Kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene or deeper Oligocene source rocks. The relation between diagenesis and reservoir quality is as follows: the initial porosity was decreased by compaction and cementation and then increased by leaching of the metastable grains and dissolution of cement. Good quality reservoir rocks were deposited in fluvial environment and hence quality of reservoir rocks is also environment selective. Porosity and permeability data exhibit good inverse correlation with cement. However, some data points indicate multiple controls on permeability. Reservoir quality is thus controlled by

Characterization of terrestrial hydrothermal alteration products with Mars analog instrumentation: Implications for current and future rover investigations

NASA Astrophysics Data System (ADS)

Black, Sarah R.; Hynek, Brian M.

2018-06-01

Interpretation of Martian geology relies heavily on our understanding of terrestrial analog deposits and our ability to obtain comprehensive and accurate mineralogical compositions. Many previous studies of terrestrial hydrothermal deposits relied on limited datasets and/or did not use instruments analogous to those deployed on Mars. We analyzed 100 hydrothermally altered basalts from Costa Rica, Nicaragua, and Iceland with Mars analog Visible to Short Wave Infrared (VSWIR) spectroscopy, X-ray Diffraction (XRD), and Raman laser spectrometry. Alteration mineralogy consisted of amorphous and crystalline SiO2 (cristobalite, tridymite, quartz), Ca/Al/Fe/Mg-sulfates (gypsum, anhydrite, alunite, jarosite, hexahydrite, alunogen), Fe-, Ti-, and Mg-oxides/hydroxides (hematite, goethite, anatase/brookite, brucite), elemental sulfur, and phyllosilicates (montmorillonite, kaolinite). Results indicate VSWIR is best suited for identification of X-ray amorphous materials such as hydrated SiO2 and phyllosilicates, while XRD is best utilized for highly ordered crystalline materials such as sulfates, crystalline SiO2 polymorphs, elemental sulfur, and Mg-hydroxides identification. Surprisingly, XRD had the lowest identification rates for Fe-oxides/hydroxides (42% compared to 61% and 75% for VNIR and Raman, respectively), and nearly equal identification rates as VSWIR for kaolinite (76% for VSWIR, 71% for XRD). Identification of phyllosilicates in XRD, while possible, is not as effective as VSWIR without extensive sample preparation. Our observed identification rates may be attributed to the relative abundance of materials-Fe-oxides/hydroxides being present as surface coatings, the presence of large amounts of kaolinite in some samples, and an increased particle size for kaolinite relative to other clays. Elemental sulfur and Fe- and Ti-oxides/hydroxides were more readily identified with Raman. With NASA's current focus on habitability, hydrothermally altered areas-which we know to

Spectroscopic mapping of the white horse alunite deposit, Marysvale volcanic field, Utah: Evidence of a magmatic component

USGS Publications Warehouse

Rockwell, B.W.; Cunningham, C.G.; Breit, G.N.; Rye, R.O.

2006-01-01

Previous studies have demonstrated that the replacement alunite deposits just north of the town of Marysvale, Utah, USA, were formed primarily by low-temperature (100??-170?? C), steam-heated processes near the early Miocene paleoground surface, immediately above convecting hydrothermal plumes. Pyrite-bearing propylitically altered rocks occur mainly beneath the steam-heated alunite and represent the sulfidized feeder zone of the H2S-dominated hydrothermal fluids, the oxidation of which at higher levels led to the formation of the alunite. Maps of surface mineralogy at the White Horse deposit generated from Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were used in conjunction with X-ray diffraction studies of field samples to test the accuracy and precision of AVIRIS-based mineral mapping of altered rocks and demonstrate the utility of spectroscopic mapping for ore deposit characterization. The mineral maps identified multiple core zones of alunite that grade laterally outward to kaolinite. Surrounding the core zones are dominantly propylitically altered rocks containing illite, montmorillonite, and chlorite, with minor pyrite, kaolinite, gypsum, and remnant potassium feldspar from the parent rhyodacitic ash-flow tuff. The AVIRIS mapping also identified fracture zones expressed by ridge-forming selvages of quartz + dickite + kaolinite that form a crude ring around the advanced argillic core zones. Laboratory analyses identified the aluminum phosphate-sulfate (APS) minerals woodhouseite and svanbergite in one sample from these dickite-bearing argillic selvages. Reflectance spectroscopy determined that the outer edges of the selvages contain more dickite than do the medial regions. The quartz + dickite ?? kaolinite ?? APS-mineral selvages demonstrate that fracture control of replacement processes is more prevalent away from the advanced argillic core zones. Although not exposed at the White Horse deposit, pyrophyllite ?? ordered illite was identified

Geology and resources of the Andersonville, Georgia, kaolin and bauxite district

USGS Publications Warehouse

Cofer, Harland E.; Manker, John Phillip

1983-01-01

The kaolin and kaolin-rich sediments of the Andersonville district were deposited in an estuary environment with restricted circulation and little tidal or longshore current influence. Micaceous kaolinitic clays were deposited during late Paleocene time on broad, shallow water flats between deeper water distributary channels in the estuarine system. During the cycle of deposition, kaolinitic sediments were temporarily exposed to weathering leading to bauxitization and further kaolinization. Subsequently, subaerial and/or subaqueous erosion planed off and redeposited some of the weathering products as organic-rich clays and silts, berthierine-bearing clays, and rarely as colluvial bauxite and sedimentary bauxitic clays. Upon resubmergence, gibbsite-rich, porous bauxite, and bauxitic clays were exposed to silica-saturated water of the estuary. Gibbsite reacted with silica to form kaolinite and resulted in the formation of the transitional (bauxitic) clays overlying the bauxite. Kaolinitic sediments transported by streams again spread over the altered and redeposited material. At the close of the kaolin depositional period movement along the Andersonville Fault Zone and related faults changed the basinal configuration, and the area of the uplifted (southern) block of the fault was exposed to weathering and bauxitization for a limited period of time. General submergence again occurred and much of the district was covered by marine and brackish water, ending the period of commercial kaolin deposition. The kaolin and bauxite deposits in the Andersonville district form a broad belt 15 kilometers wide and 22 kilometers long trending in a northwest-southeastward direction. Most of the kaolin and bauxite of commercial value occur within a narrow 10-kilometer-wide zone in the belt. The reserves of kaolin suitable for refractory and chemical use are approximately 290 million tonnes. Paramarginal resources of sandy kaolin suitable for refractory, chemical, or aluminum

Removal of cyanobacterial blooms in Taihu Lake using local soils. I. Equilibrium and kinetic screening on the flocculation of Microcystis aeruginosa using commercially available clays and minerals.

PubMed

Pan, Gang; Zhang, Ming-Ming; Chen, Hao; Zou, Hua; Yan, Hai

2006-05-01

Algal removal abilities of 26 clays/minerals were classified into three categories according to the 8-h equilibrium removal efficiency (Q8h) and removal rate at a clay loading of 0.7 g/L. Type I clays (sepiolite, talc, ferric oxide, and kaolinite) had a Q8h > 90%, a t50 (time needed to remove 50% of the algae) < 15 min, and a t80 < 2.5 h. Type II clays (6 clays) had a Q8h 50-90%, a t50 < 2.5 h, and a t80 > 2.5 h. Type III clays (14 clays) with Q8h < 50%, t50 > 8 h and t80 > 14 h had no practical value in removal of algal blooms. When the clay loading was reduced to 0.2 g/L, Q8h for all the 25 materials decreased to below 60%, except for sepiolite whose Q8h remained about 97%. The high efficiency for sepiolite to flocculate M. aeruginosa cells in freshwaters was due to the mechanism of netting and bridging effect.

Depositional environment, sand provenance, and diagenesis of the Basal Salina Formation (lower Eocene), northwestern Peru

NASA Astrophysics Data System (ADS)

Marsaglia, K. M.; Carozzi, A. V.

The Basal Salina Formation is a lower Eocene transgressive sequence consisting of interbedded shales, siltstones, and conglomeratic sandstones. This formation occurs in the Talara basin of northwestern Peru and is one of a series of complexly faulted hydrocarbon-producing formations within this extensional forearc basin. These sediments were probably deposited in a fan-delta complex that developed along the ancestral Amotape Mountains during the early Eocene. Most of the sediment was derived from the low-grade metamorphic and plutonic rocks that comprise the Amotape Mountains, and their sedimentary cover. Detrital modes of these sandstones reflect the complex tectonic history of the area, rather than the overall forearc setting. Unlike most forearc sediments, these are highly quartzose, with only minor percentages of volcanic detritus. This sand is variably indurated and cemented by chlorite, quartz, calcite, and kaolinite. Clay-mineral matrix assemblages show gradational changes with depth, from primarily detrital kaolinite to diagenetic chlorite and mixed-layered illite/smectite. Basal Salina sandstones exhibit a paragenetic sequence that may be tied to early meteoric influx or late-stage influx of thermally driven brines associated with hydrocarbon migration. Much of the porosity is secondary, resulting from a first-stage dissolution of silicic constituents (volcanic lithic fragments, feldspar, and fibrous quartz) and a later dissolution of surrounding carbonate cement. Types of pores include skeletal grains, grain molds, elongate pores, and fracture porosity. Measured porosity values range up to 24% and coarser samples tend to be more porous. Permeability is enhanced by fractures and deterred by clay-mineral cements and alteration residues.

The Lower Silurian Osmundsberg K-bentonite. Part II: Mineralogy, geochemistry, chemostratigraphy and tectonomagmatic significance

USGS Publications Warehouse

Huff, W.D.; Bergstrom, Stig M.; Kolata, Dennis R.; Sun, H.

1998-01-01

The Lower Silurian Osmundsberg K-bentonite is a widespread ash bed that occurs throughout Baltoscandia and parts of northern Europe. This paper describes its characteristics at its type locality in the Province of Dalarna, Sweden. It contains mineralogical and chemical characteristics that permit its regional correlation in sections elsewhere in Sweden as well as Norway, Estonia, Denmark and Great Britain. The < 2 ??m clay fraction of the Osmundsberg bed contains abundant kaolinite in addition to randomly ordered (RO) illite/smectite (I/S). Modelling of the X-ray diffraction tracings showed the I/S consists of 18% illite and 82 % smectite. The high smectite and kaolinite content is indicative of a history with minimal burial temperatures. Analytical data from both pristine melt inclusions in primary quartz grains as well as whole rock samples can be used to constrain both the parental magma composition and the probable tectonic setting of the source volcanoes. The parental ash was dacitic to rhyolitic in composition and originated in a tectonically active collision margin setting. Whole rock chemical fingerprinting of coeval beds elsewhere in Baltoscandia produced a pronounced clustering of these samples in the Osmundsberg field of the discriminant analysis diagram. This, together with well-constrained biostratigraphic and lithostratigraphic data, provides the basis for regional correlation and supports the conclusion that the Osmundsberg K-bentonite is one of the most extensive fallout ash beds in the early Phanerozoic. The source volcano probably lay to the west of Baltica as part of the subduction complex associated with the closure of Iapetus.

Fluvial/lacustrine diagenesis: Significance for hydrocarbon production and entrapment in the carboniferous Albert Fm, Moncton basin, NB

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noble, J.P.A.; Chowdhury, A.H.; Yu, H.

1996-12-31

The Carboniferous Horton Group Albert Formation sediments include lacustrine source-rock oil shales and fluvial porous reservoir sandstones. The petrography, stable isotopes, fluid inclusions, cathodoluminescence and mirror/trace element chemistry of these sandstones are used to establish the diagenetic history and controlling factors. Early diagenetic calcite, quartz and albite cements with minor chlorite and kaolinite are variably present and related to depositional mineralogy and lake levels winch controlled the porewater chemistry. Antitaxial veins occurring preferentially in shales are shown, from heavy {delta}C{sup 13} values and fluid inclusions, to be related to methanogenesis in overpressured zones at shallow depths. Later burial calcite andmore » extensive albitisation are related to mineral reactions during the phase of rapid subsidence at temperatures of 80{degrees} to 150{degrees} in the deepest segment of the basin, together with significant dissolution of carbonates and feldspars related mainly to organic acids generated by organic maturation processes. Mass balance calculations indicate that not enough organic matter was present to account for all the estimated secondary porosity and some evidence suggests that reactions between kaolinite and calcite/ankerite to produce chlorite, and mixed layer illite-smectite ordering reactions, produced significant secondary porosity. Burial history reconstructions and thermal modelling of the Albert Fm. sediments using Arrhenius type maturity models and reflectance and rock-eval data suggest locally variable maturation and reservoir production related to the locally different fault tectonic histories characteristic of strike-slip lacustrine segmented basins. The Horton depositional cycle was followed by major dextral transpression with local faulting and inversion and vein cementation.« less

Fluvial/lacustrine diagenesis: Significance for hydrocarbon production and entrapment in the carboniferous Albert Fm, Moncton basin, NB

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noble, J.P.A.; Chowdhury, A.H.; Yu, H.

1996-01-01

The Carboniferous Horton Group Albert Formation sediments include lacustrine source-rock oil shales and fluvial porous reservoir sandstones. The petrography, stable isotopes, fluid inclusions, cathodoluminescence and mirror/trace element chemistry of these sandstones are used to establish the diagenetic history and controlling factors. Early diagenetic calcite, quartz and albite cements with minor chlorite and kaolinite are variably present and related to depositional mineralogy and lake levels winch controlled the porewater chemistry. Antitaxial veins occurring preferentially in shales are shown, from heavy [delta]C[sup 13] values and fluid inclusions, to be related to methanogenesis in overpressured zones at shallow depths. Later burial calcite andmore » extensive albitisation are related to mineral reactions during the phase of rapid subsidence at temperatures of 80[degrees] to 150[degrees] in the deepest segment of the basin, together with significant dissolution of carbonates and feldspars related mainly to organic acids generated by organic maturation processes. Mass balance calculations indicate that not enough organic matter was present to account for all the estimated secondary porosity and some evidence suggests that reactions between kaolinite and calcite/ankerite to produce chlorite, and mixed layer illite-smectite ordering reactions, produced significant secondary porosity. Burial history reconstructions and thermal modelling of the Albert Fm. sediments using Arrhenius type maturity models and reflectance and rock-eval data suggest locally variable maturation and reservoir production related to the locally different fault tectonic histories characteristic of strike-slip lacustrine segmented basins. The Horton depositional cycle was followed by major dextral transpression with local faulting and inversion and vein cementation.« less

Acoustic emissions monitoring and synchrotron X-ray diffraction analysis of mineral dehydrations at high pressures and temperatures

NASA Astrophysics Data System (ADS)

Gasc, J.; Guillon, S.; Schubnel, A. J.; Brunet, F.; Lathe, C.; Mueller, H.

2009-12-01

We have monitored from in-situ X-ray diffraction coupled to Acoustic Emission (AE) imaging, the behavior of several materials under elevated pressures and temperatures (quartz, kaolinite, serpentinite). The samples were placed in a boron-epoxy assembly with an 8mm edge-length and loaded in the MAX80 cubic multi-anvil press installed on the German synchrotron (HASYLAB-DESY, Hamburg). AE were recorded using six piezoceramic transducers (2 MHz eigen frequency) glued on each of the six WC anvils. Full waveforms were acquired using an eight channel digital oscilloscope and a continuous acoustic recorder. Our system was first tested using quartz beads (500μm) aggregates. During cold compression performed on these samples many acoustic events were recorded and located inside the samples. These are obviously related to the fragile fracturing of the quartz due to the porosity loss. During the heating cycles performed on the same samples, the acoustic activity progressively vanishes between 300 and 400°C indicating the transition to the ductile regime towards higher temperatures. Further experiments were performed by mixing 20wt% of kaolinite to the quartz. As a result, the amount of acoustic emissions recorded during cold compression is significantly reduced. This is thought to be a result of the ductile behaviour of kaolinite even at low temperatures. This assumption has been confirmed by performing experiments on pure kaolinite which did not produce acoustic emissions during cold compression nor during heating cycles up to 1000°C (i.e. beyond the kaolinite dehydration temperature). This set of experiments clearly established that no acoustic activity is produced by the assembly and that AEs produced by the samples are accurately located by the software. The behaviour of serpentinite dehydration was then investigated under various pressure conditions (i.e. various volume changes), from ~0.6 to ~40kbars. These experiments were performed under deviatoric stress conditions

Acoustic emissions monitoring and synchrotron X-ray diffraction analysis of mineral dehydrations at high pressures and temperatures

NASA Astrophysics Data System (ADS)

Schubnel, Alexandre; Julien, Gasc; Sophie, Guillon; Fabrice, Brunet; Christian, Lathe; Hans-Joachim, Mueller

2010-05-01

We have monitored from in-situ X-ray diffraction coupled to Acoustic Emission (AE) imaging, the behavior of several materials under elevated pressures and temperatures (quartz, kaolinite, serpentinite). The samples were placed in a boron-epoxy assembly with an 8mm edge-length and loaded in the MAX80 cubic multi-anvil press installed on the German synchrotron (HASYLAB-DESY, Hamburg). AE were recorded using six piezoceramic transducers (2 MHz eigen frequency) glued on each of the six WC anvils. Full waveforms were acquired using an eight channel digital oscilloscope and a continuous acoustic recorder. Our system was first tested using quartz beads (500μm) aggregates. During cold compression performed on these samples many acoustic events were recorded and located inside the samples. These are obviously related to the fragile fracturing of the quartz due to the porosity loss. During the heating cycles performed on the same samples, the acoustic activity progressively vanishes between 300 and 400°C indicating the transition to the ductile regime towards higher temperatures. Further experiments were performed by mixing 20wt% of kaolinite to the quartz. As a result, the amount of acoustic emissions recorded during cold compression is significantly reduced. This is thought to be a result of the ductile behaviour of kaolinite even at low temperatures. This assumption has been confirmed by performing experiments on pure kaolinite which did not produce acoustic emissions during cold compression nor during heating cycles up to 1000°C (i.e. beyond the kaolinite dehydration temperature). This set of experiments clearly established that no acoustic activity is produced by the assembly and that AEs produced by the samples are accurately located by the software. The behaviour of serpentinite dehydration was then investigated under various pressure conditions (i.e. various volume changes), from ~0.6 to ~40kbars. These experiments were performed under deviatoric stress conditions

Solid-state NMR study of geopolymer prepared by sol-gel chemistry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsai, Yi-Ling; Hanna, John V.; Lee, Yuan-Ling, E-mail: yuanlinglee@ntu.edu.t

2010-12-15

Geopolymers are a new class of materials formed by the condensation of aluminosilicates and silicates obtained from natural minerals or industrial wastes. In this work, the sol-gel method is used to synthesize precursor materials for the preparation of geopolymers. The geopolymer samples prepared by our synthetic route have been characterized by a series of physical techniques, including Fourier-transform infrared, X-ray diffraction, and multinuclear solid-state NMR. The results are very similar to those obtained for the geopolymers prepared from natural kaolinite. We believe that our synthetic approach can offer a good opportunity for the medical applications of geopolymer. -- Graphical abstract:more » Geopolymer prepared by the sol-gel route has the same spectroscopic properties as the sample prepared from the natural kaolinite. Display Omitted« less

Paleoproterozoic volcanic centers of the São Félix do Xingu region, Amazonian craton, Brazil: Hydrothermal alteration and metallogenetic potential

NASA Astrophysics Data System (ADS)

da Cruz, Raquel Souza; Fernandes, Carlos Marcello Dias; Villas, Raimundo Netuno Nobre; Juliani, Caetano; Monteiro, Lena Virgínia Soares; Lagler, Bruno; Misas, Carlos Mario Echeverri

2016-06-01

Geological, petrographic, scanning electron microscopy, and X-ray diffraction studies revealed hydrothermalized lithotypes evidenced by overprinted zones of potassic, propylitic, sericitic, and intermediate argillic alterations types, with pervasive and fracture-controlled styles, in Paleoproterozoic volcano-plutonic units of the São Félix do Xingu region, Amazonian craton, northern Brazil. The Sobreiro Formation presents propylitic (epidote + chlorite + carbonate + clinozoisite + sericite + quartz ± albite ± hematite ± pyrite), sericitic (sericite + quartz + carbonate), and potassic (potassic feldspar + hematite) alterations. The prehnite-pumpellyite pair that is common in geothermal fields also occurs in this unit. The Santa Rosa Formation shows mainly potassic (biotite + microcline ± magnetite), sericitic (sericite + quartz + carbonate ± chlorite ± gold), and intermediate argillic (montmorillonite + kaolinite/halloysite + illite) alterations. These findings strongly suggest the involvement of magma-sourced and meteoric fluids and draw attention to the metallogenetic potential of these volcanic units for Paleoproterozoic epithermal and rare and base metal porphyry-type mineralizations, similar to those already identified in other portions of the Amazonian craton.

Diagenetic mineralization in Pennsylvanian coals from Indiana, USA: 13C/12C and 18O/16O implications for cleat origin and coalbed methane generation

USGS Publications Warehouse

Solano-Acosta, W.; Schimmelmann, A.; Mastalerz, Maria; Arango, I.

2008-01-01

Cleats and fractures in southwestern Indiana coal seams are often filled with authigenic kaolinite and/or calcite. Carbon- and oxygen-stable isotope ratios of kaolinite, calcite, and coalbed CO2 were evaluated in combination with measured values and published estimates of ??18O of coalbed paleowaters that had been present at the time of mineralization. ??18Omineral and ??18Owater values jointly constrain the paleotemperature of mineralization. The isotopic evidence and the thermal and tectonic history of this part of the Illinois Basin led to the conclusion that maximum burial and heat-sterilization of coal seams approximately 272??Ma ago was followed by advective heat redistribution and concurrent precipitation of kaolinite in cleats at a burial depth of < 1600??m at ??? 78 ?? 5????C. Post-Paleozoic uplift, the development of a second generation of cleats, and subsequent precipitation of calcite occurred at shallower burial depth between ??? 500 to ??? 1300??m at a lower temperature of 43 ?? 6????C. The available paleowater in coalbeds was likely ocean water and/or tropical meteoric water with a ??18Owater ??? - 1.25??? versus VSMOW. Inoculation of coalbeds with methanogenic CO2-reducing microbes occurred at an even later time, because modern microbially influenced 13C-enriched coalbed CO2 (i.e., the isotopically fractionated residue of microbial CO2 reduction) is out of isotopic equilibrium with 13C-depleted calcite in cleats. ?? 2007 Elsevier B.V. All rights reserved.

δ30Si systematics in a granitic saprolite, Puerto Rico

USGS Publications Warehouse

Ziegler, Karen; Chadwick, Oliver A.; White, Arthur F.; Brzezinski, Mark A.

2005-01-01

Granite weathering and clay mineral formation impart distinct and interpretable stable Si isotope (δ30Si) signatures to their solid and aqueous products. Within a saprolite, clay minerals have δ30Si values ∼2.0‰ more negative than their parent mineral and the δ30Si signature of the bulk solid is determined by the ratio of primary to secondary minerals. Mineral-specific weathering reactions predominate at different depths, driving changes in differing δ30Sipore watervalues. At the bedrock-saprolite interface, dissolution of plagioclase and hornblende creates δ30Sipore water signatures more positive than granite by up to 1.2‰; these reactions are the main contributor of Si to stream water and determine its δ30Si value. Throughout the saprolite, biotite weathering releases Si to pore waters but kaolinite overgrowth formation modulates its contribution to pore-water Si. The influence of biotite on δ30Sipore water is greatest near the bedrock where biotite-derived Si mixes with bulk pore water prior to kaolinite formation. Higher in the saprolite, biotite grains have become more isolated by kaolinite overgrowth, which consumes biotite-derived Si that would otherwise influence δ30Sipore water. Because of this isolation, which shifts the dominant source of pore-water Si from biotite to quartz, δ30Sipore water values are more negative than granite by up to 1.3‰ near the top of the saprolite.

Reservoir assessment of the Nubian sandstone reservoir in South Central Gulf of Suez, Egypt

NASA Astrophysics Data System (ADS)

El-Gendy, Nader; Barakat, Moataz; Abdallah, Hamed

2017-05-01

The Gulf of Suez is considered as one of the most important petroleum provinces in Egypt and contains the Saqqara and Edfu oil fields located in the South Central portion of the Gulf of Suez. The Nubian sandstone reservoir in the Gulf of Suez basin is well known for its great capability to store and produce large volumes of hydrocarbons. The Nubian sandstone overlies basement rocks throughout most of the Gulf of Suez region. It consists of a sequence of sandstones and shales of Paleozoic to Cretaceous age. The Nubian sandstone intersected in most wells has excellent reservoir characteristics. Its porosity is controlled by sedimentation style and diagenesis. The cementation materials are mainly kaolinite and quartz overgrowths. The permeability of the Nubian sandstone is mainly controlled by grain size, sorting, porosity and clay content especially kaolinite and decreases with increase of kaolinite. The permeability of the Nubian Sandstone is evaluated using the Nuclear Magnetic Resonance (NMR technology) and formation pressure data in addition to the conventional logs and the results were calibrated using core data. In this work, the Nubian sandstone was investigated and evaluated using complete suites of conventional and advanced logging techniques to understand its reservoir characteristics which have impact on economics of oil recovery. The Nubian reservoir has a complicated wettability nature which affects the petrophysical evaluation and reservoir productivity. So, understanding the reservoir wettability is very important for managing well performance, productivity and oil recovery.

Conservatism of Late Pennsylvanian vegetational patterns during short-term cyclic and long-term directional environmental change, western equatorial Pangea.

PubMed

Tabor, Neil J; Romanchock, Charles M; Looy, Cynthia V; Hotton, Carol L; Dimichele, William A; Chaney, Dan S

2013-09-19

Patterns of plant distribution by palaeoenvironment were examined across the Pennsylvanian-Permian transition in North-Central Texas. Stratigraphically recurrent packages of distinct lithofacies, representing different habitats, contain qualitatively and quantitatively different macrofloras and microfloras. The species pools demonstrate niche conservatism, remaining closely tied to specific habitats, during both short-term cyclic environmental change and a long-term trend of increasing aridity. The deposits examined principally comprise the terrestrial Markley and its approximate marine equivalent, the Harpersville Formation and parts of lower Archer City Formation. Fossiliferous deposits are lens-like, likely representing fill sequences of channels formed during abandonment phases. Palaeosols, represented by blocky mudstones, comprise a large fraction of the deposits. They suggest progressive climate change from minimally seasonal humid to seasonal subhumid to seasonal dry subhumid. Five lithofacies yielded plants: kaolinite-dominated siltstone, organic shale, mudstone beds within organic shale, coarsening upward mudstone-sandstone interbeds and channel sandstone. Both macro- and microflora were examined. Lithofacies proved compositionally distinct, with different patterns of dominance diversity. Organic shales (swamp deposits), mudstone partings (swamp drainages) and coarsening upward mudstone-sandstone interbeds (floodplains) typically contain Pennsylvanian wetland vegetation. Kaolinite-dominated siltstones and (to the extent known) sandstones contain taxa indicative of seasonally dry substrates. Some kaolinite-dominated siltstones and organic shales/coals yielded palynomorphs. Microfloras are more diverse, with greater wetland-dryland overlap than macrofloras. It appears that these two floras were coexistent at times on the regional landscape.

Conservatism of Late Pennsylvanian vegetational patterns during short-term cyclic and long-term directional environmental change, western equatorial Pangea

PubMed Central

TABOR, NEIL J.; ROMANCHOCK, CHARLES M.; LOOY, CYNTHIA V.; HOTTON, CAROL L.; DIMICHELE, WILLIAM A.; CHANEY, DAN S.

2014-01-01

Patterns of plant distribution by palaeoenvironment were examined across the Pennsylvanian–Permian transition in North–Central Texas. Stratigraphically recurrent packages of distinct lithofacies, representing different habitats, contain qualitatively and quantitatively different macrofloras and microfloras. The species pools demonstrate niche conservatism, remaining closely tied to specific habitats, during both short-term cyclic environmental change and a long-term trend of increasing aridity. The deposits examined principally comprise the terrestrial Markley and its approximate marine equivalent, the Harpersville Formation and parts of lower Archer City Formation. Fossiliferous deposits are lens-like, likely representing fill sequences of channels formed during abandonment phases. Palaeosols, represented by blocky mudstones, comprise a large fraction of the deposits. They suggest progressive climate change from minimally seasonal humid to seasonal subhumid to seasonal dry subhumid. Five lithofacies yielded plants: kaolinite-dominated siltstone, organic shale, mudstone beds within organic shale, coarsening upward mudstone–sandstone interbeds and channel sandstone. Both macro- and microflora were examined. Lithofacies proved compositionally distinct, with different patterns of dominance diversity. Organic shales (swamp deposits), mudstone partings (swamp drainages) and coarsening upward mudstone–sandstone interbeds (floodplains) typically contain Pennsylvanian wetland vegetation. Kaolinite-dominated siltstones and (to the extent known) sandstones contain taxa indicative of seasonally dry substrates. Some kaolinite-dominated siltstones and organic shales/coals yielded palynomorphs. Microfloras are more diverse, with greater wetland–dryland overlap than macrofloras. It appears that these two floras were coexistent at times on the regional landscape. PMID:25339793

Secondary precious metal enrichment by steam-heated fluids in the Crofoot-Lewis hot spring gold-silver deposit and relation to paleoclimate

USGS Publications Warehouse

Ebert, S.W.; Rye, R.O.

1997-01-01

The Crofoot-Lewis deposit is an adularia-sericite-type (low-sulfidation) epithermal Au-Ag deposit, whose well-preserved paleosurface includes abundant opaline sinters, widespread and intense silicification, bedded hydrothermal eruption breccias, and a large zone of acid sulfate alteration. Radiogenic isotope ages indicate that the system was relatively long-lived, with hydrothermal activity starting around 4 Ma and extending, at least intermittently, for the next 3 m.y. Field evidence indicates that the surficial zone of acid sulfate alteration formed in a steam-heated environment within an active geothermal system. A drop in the water table enabled descending acid sulfate waters to leach Au and Ag from zones of low-grade disseminated mineralization, resulting in the redistribution and concentration of Au and Ag into ore-grade concentrations. These zones of secondary Au-Ag enrichment are associated with opal + alunite + kaolinite + montmorillonite ?? hematite and were deposited in open space fractures at, and within a few tens of meters below, the paleowater table. The stable isotope systematics of alunite and kaolinite in the steam-heated environment are relatively complex, due to variations in the residence time of aqueous SO4 that formed from the oxidation of H2S prior to precipitation of alunite, and the susceptibility of fine-grained kaolinites to hydrogen isotope exchange with later waters. Most of the alunites are enriched in 34S relative to early sulfide minerals, reflecting partial S isotope exchange between aqueous SO4 and H2S. About half of the alunites give reasonable calculated ??18OSO4-OH temperatures for a steam-heated environment indicating O isotope equilibrium between aqueous SO4 and water. The ??5DH2O values of the hydrothermal fluids varied by almost 60 per mil over the life of the meteoric water-dominated system, suggesting significant climate changes. Mineralization is believed to have resulted from large-scale convection of meteoric water

Mapping advanced argillic alteration zones with ASTER and Hyperion data in the Andes Mountains of Peru

NASA Astrophysics Data System (ADS)

Ramos, Yuddy; Goïta, Kalifa; Péloquin, Stéphane

2016-04-01

This study evaluates Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) and Hyperion hyperspectral sensor datasets to detect advanced argillic minerals. The spectral signatures of some alteration clay minerals, such as dickite and alunite, have similar absorption features; thus separating them using multispectral satellite images is a complex challenge. However, Hyperion with its fine spectral bands has potential for good separability of features. The Spectral Angle Mapper algorithm was used in this study to map three advanced argillic alteration minerals (alunite, kaolinite, and dickite) in a known alteration zone in the Peruvian Andes. The results from ASTER and Hyperion were analyzed, compared, and validated using a Portable Infrared Mineral Analyzer field spectrometer. The alterations corresponding to kaolinite and alunite were detected with both ASTER and Hyperion (80% to 84% accuracy). However, the dickite mineral was identified only with Hyperion (82% accuracy).

ADSORPTION OF ORGANIC CATIONS TO NATURAL MATERIALS

EPA Science Inventory

The factors that control the extent of adsorption of amphiphilic organic cations on environmental and pristine surfaces have been studied. The sorbents were kaolinite, montmorillonite, two aquifer materials, and a soil; solutions contained various concentrations of NaCl and CaCl,...

Beneficial reuse of fly ashes in geotechnical engineering with physicochemical and electron microscopic methods.

DOT National Transportation Integrated Search

2013-06-01

The sedimentation behavior of fine grained soil is largely dependent on its pore fluid chemistry. Physicochemical properties of the : pore fluid, such as ionic strength and pH, could greatly influence the micro structure of kaolinite which in turn in...

Typing is writing: Linguistic properties modulate typing execution.

PubMed

Pinet, Svetlana; Ziegler, Johannes C; Alario, F-Xavier

2016-12-01

Typing is becoming our preferred way of writing. Perhaps because of the relative recency of this change, very few studies have investigated typing from a psycholinguistic perspective. In addition, and despite obvious similarities between typing and handwriting, typing research has remained rather disconnected from handwriting research. The current study aimed at bridging this gap by evaluating how typing is affected by a number of psycholinguistic variables defined at the word, syllable, and letter levels. In a writing-to-dictation task, we assessed typing performance by measuring response accuracy, onset latencies - an index of response preparation and initiation - and interkeystroke intervals (IKIs) - an index of response execution processes. The lexical and sublexical factors revealed a composite pattern of effects. Lexical frequency improved response latencies and accuracy, while bigram frequency speeded up IKIs. Sound-spelling consistency improved latencies, but had an inhibitory effect on IKI. IKIs were also longer at syllable boundaries. Together, our findings can be fit within a framework for typed production that combines the previously developed theories of spelling and typing execution. At their interface, we highlight the need for an intermediate hierarchical stage, perhaps in the form of a graphemic buffer for typing.

Mapping advanced argillic alteration at Cuprite, Nevada, using imaging spectroscopy

USGS Publications Warehouse

Swayze, Gregg A.; Clark, Roger N.; Goetz, Alexander F.H.; Livo, K. Eric; Breit, George N.; Kruse, Fred A.; Sutley, Stephen J.; Snee, Lawrence W.; Lowers, Heather A.; Post, James L.; Stoffregen, Roger E.; Ashley, Roger P.

2014-01-01

Mineral maps based on Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data were used to study late Miocene advanced argillic alteration at Cuprite, Nevada. Distributions of Fe-bearing minerals, clays, micas, sulfates, and carbonates were mapped using the Tetracorder spectral-shape matching system. The Al content of white micas increases toward altered areas and near intrusive rocks. Alunite composition varies from pure K to intimate mixtures of Na-K endmembers with subpixel occurrences of huangite, the Ca analogue of alunite. Intimately mixed Na-K alunite marks areas of relatively lower alteration temperature, whereas co-occurring Na-alunite and dickite may delineate relict hydrothermal conduits. The presence of dickite, halloysite, and well-ordered kaolinite, but absence of disordered kaolinite, is consistent with acidic conditions during hydrothermal alteration. Partial lichen cover on opal spectrally mimics chalcedony, limiting its detection to lichen-free areas. Pods of buddingtonite are remnants of initial quartz-adularia-smectite alteration. Thus, spectral maps provide a synoptic view of the surface mineralogy, and define a previously unrecognized early steam-heated hydrothermal event.Faulting and episodes of hydrothermal alteration at Cuprite were intimately linked to upper plate movements above the Silver Peak-Lone Mountain detachment and growth, collapse, and resurgence of the nearby Stonewall Mountain volcanic complex between 8 and 5 Ma. Isotopic dating indicates that hydrothermal activity started at least by 7.61 Ma and ended by about 6.2 Ma. Spectral and stable isotope data suggest that Cuprite is a late Miocene low-sulfidation adularia-sericite type hot spring deposit overprinted by late-stage, steam-heated advanced argillic alteration formed along the margin of the Stonewall Mountain caldera.

Fire Events and Soil Thermometry: The Applications of Clay Chemistry for Tracing Temperature Changes in Soils and Sediments Below Surface Fires

NASA Astrophysics Data System (ADS)

Watson, E.; Werts, S. P.; Gelabert, M.

2016-12-01

Fires in the natural environment affect the physical, chemical, and biological properties of soils. However, fires may also alter the mineralogy of the geologic material in which it comes in contact. Previous experiments on high temperature alteration of clays indicate that dehydration, oxidation, and hydroxylation in clay minerals can occur progressively in that order at increasing temperatures up to 500°C. It is also well known that wildfire events can heat soils to these temperature ranges several centimeters deep. In this experiment, alterations in clay chemistry were used as a tool to investigate fire intensity along with the changing morphology of clay minerals. For data collection, small camp fires were set in York County, SC and temperatures were recorded using a datalogger system to 5 cm deep during the fire event. Control samples were taken adjacent to the fires to compare the changing morphology of the minerals when heated. Powder x-ray diffraction and scanning electron microscopy were used to identify the clay mineralogy. The clay from soil samples was identified as hydrous kaolinite, anhydrous kaolinite, and varying types of goethite. To observe the dehydration, oxidation, and hydroxylation of clay minerals, scanning electron microscopy with emission dispersive spectroscopy was used to identify the O/cation ratios present, which would indicate changes in the oxidation state of the clay minerals. By mapping the changes in O/cation ratios with temperature in silicates, we are able to trace the temperature of the sediments during fire events. This research suggests it may be possible to utilize these geochemical trends to aid in soil and sediment temperature investigations in both archeological and modern soil and surface process investigations.

Blood typing

MedlinePlus

... matching; Rh typing; ABO blood typing; Blood group; Anemia - immune hemolytic blood type; ABO blood type; A ... during pregnancy. Careful testing can prevent a severe anemia in the newborn and jaundice .

Significance of the giant Lower Cretaceous paleoweathering event

NASA Astrophysics Data System (ADS)

Thiry, Médard; Ricordel-Prognon, Caroline; Schmitt, Jean-Michel

2010-05-01

Weathering profiles typically develop at the interface with the atmosphere, and thus, record the fluctuations in the paleoatmosphere's chemistry and climatic conditions. Consequently they are one of the main archives to upgrade our understanding on paleoclimate and the Earth's environmental history. In this presentation, we will focus on the linking between paleoatmosphere compositions, weathering rates, and their impact on the subsequent sedimentary records. Distribution of the Lower Cretaceous lateritic weathering facies. During the Early Cretaceous, sea level drops and wide exondations lead to development of deep "lateritic" weathering profiles. Thick kaolinitic weathering profiles occured on the Hercynian basements and diverse kaolinitic and ferruginous weathering products covered the Jurassic limestone platforms. This major lateritic event is not restricted to Europe but also well know in North-America (up to Canada), South-America (down to Argentina), and in Australia. Moreover, recent paleomagnetic and radiometric datations revealed that numerous kaolinitic and ferruginous formations, which classically were ascribed to Tertiary ages, date back to the Lower Cretaceous period (Thiry et al., 2006). Additionally, the Bonherz iron ore deposits in the paleokarsts of the Jurassic limestone plateform of the Paris Basin also have to be reconsidered as of Cretaceous age, probably as well as the Tertiary age of the Swiss and Bavarian Jura Bonherz. Paleoclimatic interpretation. During a long time, the interpretation of these paleoweathering features has been a major palaeoclimatic argument. The spreading out of deep kaolinitic weathering profiles (from the Scandinavian and Canadian shields to southern Argentina and Australia, which was still situated close to Antarctica at that time) has lead to considerations, that during this period a warm and wet climate prevailed globally, with very little latitudinal differentiation. These paleoclimatic interpretations stand in

Clay alteration and gold deposition in the genesis and blue star deposits, Eureka County, Nevada

USGS Publications Warehouse

Drews-Armitage, S. P.; Romberger, S.B.; Whitney, C.G.

1996-01-01

The Genesis and Blue Star sedimentary rock-hosted gold deposits occur within the 40-mile-long Carlin trend and are located in Eureka County, Nevada. The deposits are hosted within the Devonian calcareous Popovich Formation, the siliciclastic Rodeo Creek unit and the siliciclastic Vinini Formation. The host rocks have undergone contact metamorphism, decalcification, silicification, argillization, and supergene oxidation. Detailed characterization of the alteration patterns, mineralogy, modes of occurrence, and associated geochemistry of clay minerals resulted in the following classifications: least altered rocks, found distal to the orebody, consisting of both metamorphosed and unmetamorphosed host rock that has not been completely decalcified; and altered rocks, found proximal to the orebody that have been decalcified. Altered rocks are classified further into the following groups based on clay mineral content: silicic, 1 to 10 percent clay; silicicargillic, 10 to 35 percent clay; and argillic, 35 to 80 percent clay. Clay species identified are 1M illite, 2M1 illite, kaolinite, halloysite, and dioctahedral smectite. An early hydrothermal event resulted in the precipitation of euhedral kaolinite and at least one generation of silica. This event occurred contemporaneously with decalcification which increased rock permeability and porosity. A second clay alteration event resulted in the precipitation of hydrothermal 1M illite which replaced hydrothermal kaolinite and is associated with gold deposition. Silver and silica deposition is also associated with this phase of hydrothermal alteration. Hydrothermal alteration was followed by supergene alteration which resulted in the formation of supergene kaolinite, halloysite, and smectite as well as the oxidation of iron-bearing minerals. Supergene clays are concentrated along faults, dike margins, and within rocks containing carbonate. Gold mineralization is not associated with supergene clay minerals within the Genesis and

The contribution of lateritization processes to the formation of the kaolin deposits from eastern Amazon

NASA Astrophysics Data System (ADS)

da Costa, Marcondes Lima; Sousa, Daniel José Lima; Angélica, Rômulo Simões

The eastern region of the Amazon is home to the most important kaolin bauxite producing district in Brazil, referred to as the Paragominas-Capim kaolin bauxite district, which has a reserve of at least 1.0 billion tons of high-quality kaolin used in the paper coating industry. The kaolin deposits are closely related to sedimentary rocks of the Parnaíba basin and their lateritic cover. Two large deposits are already being mined: IRCC (Ipixuna) and PPSA (Paragominas). The geology of the IRCC mine is comprised of the kaolin-bearing lower unit (truncated mature laterite succession derived from the Ipixuna/Itapecuru formation) and the upper unit (immature lateritized Barreiras formation). The lower kaolin unit is characterized by a sandy facies at the bottom and a soft (ore) with flint facies at the top. It is formed by kaolinite, quartz, some iron oxi-hydroxides, mica and several accessories and heavy minerals. The <2 μm kaolinite crystallites only correspond to 41.3-58.3% of the soft kaolin, and large booklets of 15-300 μm are common. The degree of structure order of kaolinite decreases towards the flint kaolin. The chemical composition of the soft kaolin is similar to the theoretical chemical composition of kaolinite, with low iron content, and can be well correlated to most kaolin deposits in the region. The distribution pattern of chemical elements from sandy to flint kaolin (lower unit) suggests a lateritic evolution and erosive truncation. This is quite distinct from the upper unit, which has a mineralogical and chemical pathway relating it to a complete immature lateritic profile. The geological evolution of the IRCC kaolin is similar to that of other deposits in the eastern Amazon region, being comprised of: parent rocks formed in an estuarine marine and fluvio-laccustrine environment during the early Cretaceous; establishment of mature lateritization with the formation of kaolin in the Eocene; marine transgression and regression - (Pirabas and Barreiras

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2012 CFR

2012-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2011 CFR

2011-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2013 CFR

2013-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2010 CFR

2010-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

Modeling selenate adsorption behavior on oxides, clay minerals, and soils using the triple layer model

USDA-ARS?s Scientific Manuscript database

Selenate adsorption behavior was investigated on amorphous aluminum oxide, amorphous iron oxide, goethite, clay minerals: kaolinites, montmorillonites, illite, and 18 soil samples from Hawaii, and the Southwestern and the Midwestern regions of the US as a function of solution pH. Selenate adsorpti...

Modeling selenite adsorption envelopes on oxides, clay minerals, and soils using the triple layer model

USDA-ARS?s Scientific Manuscript database

Selenite adsorption behavior was investigated on amorphous aluminum and iron oxides, clay minerals: kaolinite, montmorillonite, and illite, and 45 surface and subsurface soil samples from the Southwestern and Midwestern regions of the USA as a function of solution pH. Selenite adsorption decreased ...

Biochar impact on water infiltration and water quality through a compacted subsoil layer

EPA Science Inventory

Soils in the SE USA Coastal Plain region frequently have a compacted subsoil layer (E horizon), which is a barrier for water infiltration. Four different biochars were evaluated to increase water infiltration through a compacted horizon from a Norfolk soil (fine-loamy, kaolinitic...

The clays of the United States east of the Mississippi River

USGS Publications Warehouse

Ries, Henrich

1903-01-01

Since clays vary mineralogically they vary also chemically, but the plasticity may remain the same through a wide range of chemical composition, and this property is evidently not dependent on the chemical composition alone, but is due rather to some physical cause. The plasticity may be destroyed by heating the clay to a sufficiently high temperature to drive off the chemically combined water. Although varying in their mineral composition, most clays are supposed to contain more or less of the mineral kaolinite (a hydrated silicate of alumina), which is commonly referred to as the clay base or clay substance. The adoption of the latter term has probably arisen from the fact that many have 'considered this mineral to be the cause of plasticity, an idea now known to be somewhat incorrect, because some of the most plastic clays contain but small quantities of kaolinite, and vice versa. 

Water and Sediment Quality in the Yukon River Basin, Alaska, During Water Year 2005

DTIC Science & Technology

2007-01-01

Disordered Kaolinite 0.6 0.5 0.4 0.7 0.6 1.0 0.4 Ferruginous smectite 7.4 9.5 6.1 4.9 9.4 10.6 12.4 Illite + Smectite 6.8 4.8 5.2 6.6 6.6 5.5 4.9...64.7 Clays: Goethite 0.1 0.1 0.3 0.1 0.1 0.3 0.1 Disordered Kaolinite 0.6 0.9 0.3 0.7 0.9 0.6 0.7 Ferruginous smectite 7.0 6.8 7.1...7.9 7.6 16.4 15.7 Illite + Smectite 10.2 7.7 8.1 7.9 6.8 1.2 3.2 Chlorite 8.0 9.5 9.6 9.4 10.7 10.8 12.2 Muscovite (2M1) 4.1 6.0 5.2 4.8 4.1 4.8

49 CFR 192.175 - Pipe-type and bottle-type holders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 3 2011-10-01 2011-10-01 false Pipe-type and bottle-type holders. 192.175 Section....175 Pipe-type and bottle-type holders. (a) Each pipe-type and bottle-type holder must be designed so... equipment, that might cause corrosion or interfere with the safe operation of the holder. (b) Each pipe-type...

49 CFR 192.175 - Pipe-type and bottle-type holders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Pipe-type and bottle-type holders. 192.175 Section....175 Pipe-type and bottle-type holders. (a) Each pipe-type and bottle-type holder must be designed so... equipment, that might cause corrosion or interfere with the safe operation of the holder. (b) Each pipe-type...

Characterization of phyllosilicates observed in the central Mawrth Vallis region, Mars, their potential formational processes, and implications for past climate

USGS Publications Warehouse

McKeown, N.K.; Bishop, J.L.; Noe Dobrea, E.Z.; Ehlmann, B.L.; Parente, M.; Mustard, J.F.; Murchie, S.L.; Swayze, G.A.; Bibring, J.-P.; Silver, E.A.

2009-01-01

Mawrth Vallis contains one of the largest exposures of phyllosilicates on Mars. Nontronite, montmorillonite, kaolinite, and hydrated silica have been identified throughout the region using data from the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM). In addition, saponite has been identified in one observation within a crater. These individual minerals are identified and distinguished by features at 1.38-1.42, ???1.91, and 2.17-2.41 ??m. There are two main phyllosilicate units in the Mawrth Vallis region. The lowermost unit is nontronite bearing, unconformably overlain by an Al-phyllosilicate unit containing montmorillonite plus hydrated silica, with a thin layer of kaolinite plus hydrated silica at the top of the unit. These two units are draped by a spectrally unremarkable capping unit. Smectites generally form in neutral to alkaline environments, while kaolinite and hydrated silica typically form in slightly acidic conditions; thus, the observed phyllosilicates may reflect a change in aqueous chemistry. Spectra retrieved near the boundary between the nontronite and Al-phyllosilicate units exhibit a strong positive slope from 1 to 2 ??m, likely from a ferrous component within the rock. This ferrous component indicates either rapid deposition in an oxidizing environment or reducing conditions. Formation of each of the phyllosilicate minerals identified requires liquid water, thus indicating a regional wet period in the Noachian when these units formed. The two main phyllosilicate units may be extensive layers of altered volcanic ash. Other potential formational processes include sediment deposition into a marine or lacustrine basin or pedogenesis. Copyright 2009 by the American Geophysical Union.

Bacillus subtilis biofilm development in the presence of soil clay minerals and iron oxides.

PubMed

Ma, Wenting; Peng, Donghai; Walker, Sharon L; Cao, Bin; Gao, Chun-Hui; Huang, Qiaoyun; Cai, Peng

2017-01-01

Clay minerals and metal oxides, as important parts of the soil matrix, play crucial roles in the development of microbial communities. However, the mechanism underlying such a process, particularly on the formation of soil biofilm, remains poorly understood. Here, we investigated the effects of montmorillonite, kaolinite, and goethite on the biofilm formation of the representative soil bacteria Bacillus subtilis . The bacterial biofilm formation in goethite was found to be impaired in the initial 24 h but burst at 48 h in the liquid-air interface. Confocal laser scanning microscopy showed that the biofilm biomass in goethite was 3-16 times that of the control, montmorillonite, and kaolinite at 48 h. Live/Dead staining showed that cells had the highest death rate of 60% after 4 h of contact with goethite, followed by kaolinite and montmorillonite. Atomic force microscopy showed that the interaction between goethite and bacteria may injure bacterial cells by puncturing cell wall, leading to the swarming of bacteria toward the liquid-air interface. Additionally, the expressions of abrB and sinR , key players in regulating the biofilm formation, were upregulated at 24 h and downregulated at 48 h in goethite, indicating the initial adaptation of the cells to minerals. A model was proposed to describe the effects of goethite on the biofilm formation. Our findings may facilitate a better understanding of the roles of soil clays in biofilm development and the manipulation of bacterial compositions through controlling the biofilm in soils.

Continental weathering as a driver of Late Cretaceous cooling: new insights from clay mineralogy of Campanian sediments from the southern Tethyan margin to the Boreal realm

NASA Astrophysics Data System (ADS)

Chenot, Elise; Deconinck, Jean-François; Pucéat, Emmanuelle; Pellenard, Pierre; Guiraud, Michel; Jaubert, Maxime; Jarvis, Ian; Thibault, Nicolas; Cocquerez, Théophile; Bruneau, Ludovic; Razmjooei, Mohammad J.; Boussaha, Myriam; Richard, James; Sizun, Jean-Pierre; Stemmerik, Lars

2018-03-01

New clay mineralogical analyses have been performed on Campanian sediments from the Tethyan and Boreal realms along a palaeolatitudinal transect from 45° to 20°N (Danish Basin, North Sea, Paris Basin, Mons Basin, Aquitaine Basin, Umbria-Marche Basin and Tunisian Atlas). Significant terrigenous inputs are evidenced by increasing proportions of detrital clay minerals such as illite, kaolinite and chlorite at various levels in the mid- to upper Campanian, while smectitic minerals predominate and represented the background of the Late Cretaceous clay sedimentation. Our new results highlight a distinct latitudinal distribution of clay minerals, with the occurrence of kaolinite in southern sections and an almost total absence of this mineral in northern areas. This latitudinal trend points to an at least partial climatic control on clay mineral sedimentation, with a humid zone developed between 20° and 35°N. The association and co-evolution of illite, chlorite and kaolinite in most sections suggest a reworking of these minerals from basement rocks weathered by hydrolysis, which we link to the formation of relief around the Tethys due to compression associated with incipient Tethyan closure. Diachronism in the occurrence of detrital minerals between sections, with detrital input starting earlier during the Santonian in the south than in the north, highlights the northward progression of the deformation related to the anticlockwise rotation of Africa. Increasing continental weathering and erosion, evidenced by our clay mineralogical data through the Campanian, may have resulted in enhanced CO2 consumption by silicate weathering, thereby contributing to Late Cretaceous climatic cooling.

Mineralogical variation in the size fractions of a Ranong kaolin, southern Thailand

NASA Astrophysics Data System (ADS)

Pisutha-Arnond, Visut; Phuvichit, Suraphol; Leepowpanth, Quanchai

A representative crude Ranong kaolin from the Thungkla-Ranong mine was separated into > 2 mm (granule), 2-1 mm (very coarse sand), 1-0.5 mm (coarse sand), 0.5-0.25 mm (medium sand), 0.25-0.125 mm (fine sand), 0.125-0.062 mm (very fine sand) and 62-28, 28-14, 17-7, 7-4, 4-2, 2-1 and < 1 μ m size fractions. Those size fractions were analyzed by X-ray powder diffractometry (XRD), differential thermal analysis (DTA), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) with attached energy dispersive X-ray spectrometer (EDX). Kaolin group minerals were differentiated by using XRD in combination with various chemical and heat treatments together with TEM, SEM and DTA. The Ranong kaolin consists predominantly of tubular halloysite, poorly crystallized kaolinite and quartz with minor amounts of mica and K-feldspars. Other trace constituents include gibbsite, tourmaline, zircon and colored impurities (i.e. extractable iron hydroxide coating on clay mineral surface). The kaolin minerals are found in all size fractions by which their contents and halloysite/kaolinite ratios increase as the particle sizes become finer. Quartz and mica are also detected in almost all size fractions. They are, however, more abundant with coarsening particle size. Gibbsite, K-feldspar and tourmaline are mainly concentrated in the fine sand to silt size fractions. Crystallinity of kaolin minerals as measured by XRD varied moderately with size. Relatively pure kaolin minerals, predominantly halloysite and kaolinite, can be obtained in the particle size below 1 or 2 μm.

Occurrence and origin of minerals in a chamosite-bearing coal of Late Permian age, Zhaotong, Yunnan, China

USGS Publications Warehouse

Dai, S.; Chou, C.-L.

2007-01-01

The minerals found in the no.5 coal (Late Permian) from the Zhaotong Coalfield, Yunnan Province, southwestern China, have been examined and found to consist mainly of kaolinite, pyrite, chamosite, quartz, and calcite, with trace amounts of illite and mixed-layer illite-smectite. The proportion of chamosite in clay minerals ranges from 32 to 56 wt%, with an average of 46 wt%. Chamosite is distributed not only in collodetrinite, but also occurs as cell fillings in fusinite, semifusinite, and telinite. The high content and mode of occurrence of chamosite in this mine indicate its formation by interaction of kaolinite with Fe-Mg-rich fluids during early diagenesis. Except for a minor amount of terfigenous quartz, most quartz is of authigenic origin and formed from kaolinite desilication. The calcite content of the no. 5 coal is 1.4-6.3% (with an average of 3%) and is distributed in collodetrinite and as cell fillings of coal-forming plants. Calcite originated from seawater invasion during peat accumulation. Pyrite occurs in several ways: as massive, framboidal, isolated enhedral/ anhedral, and euhedral forms. In addition, the presence of a large amount of pyritized red algae provides strong evidence of seawater invasion during peat accumulation. The red algae may have played an important role in the enrichment of sulfur in the coal. The characteristic assemblage of minerals in this mine resulted from a unique basinal environment in which the mineral matter was derived from a basaltic source region, volcanic activity, and seawater transgression during coal formation.

EFFECT OF AQUEOUS PHASE PROPERTIES ON CLAY PARTICLE ZETA POTENTIAL AND ELECTRO-OSMOTIC PERMEABILITY: IMPLICATIONS FOR ELECTRO-KINETIC SOIL REMEDIATION PROCESSES

EPA Science Inventory

The influence of aqueous phase properties (pH, ionic strength and divalent metal ion concentration) on clay particle zeta potential and packed-bed electro-osmotic permeability was quantified. Although pH strongly altered the zeta potential of a Georgia kaolinite, it did not signi...

A Scale Model of Cation Exchange for Classroom Demonstration.

ERIC Educational Resources Information Center

Guertal, E. A.; Hattey, J. A.

1996-01-01

Describes a project that developed a scale model of cation exchange that can be used for a classroom demonstration. The model uses kaolinite clay, nails, plywood, and foam balls to enable students to gain a better understanding of the exchange complex of soil clays. (DDR)

Mapping Acid Sulfate Alteration of Basaltic Andesite with Thermal Infrared Data

NASA Technical Reports Server (NTRS)

Vaughan, R. G.; Calvin, W. M.; Hook, S. J.; Taranik, J. V.

2002-01-01

Airborne thermal infrared multi- and hyperspectral data sets are used to map sulfate alteration of basaltic andesites near Reno, NV. Alteration includes quartz-alunite, jarosite and a number of clay minerals such as kaolinite and montmorillonite. Additional information is contained in the original extended abstract.

Biochars impact on water infiltration and water quality through a compacted subsoil layer

USDA-ARS?s Scientific Manuscript database

Soils in the Southeastern United States Coastal Plain region frequently have a compacted subsoil layer, which is a barrier for water movement. Four different biochars were evaluated to increase water movement through a compacted horizon from a Norfolk soil (fine-loamy, kaolinitic, thermic, Typic Ka...

Updating signal typing in voice: addition of type 4 signals.

PubMed

Sprecher, Alicia; Olszewski, Aleksandra; Jiang, Jack J; Zhang, Yu

2010-06-01

The addition of a fourth type of voice to Titze's voice classification scheme is proposed. This fourth voice type is characterized by primarily stochastic noise behavior and is therefore unsuitable for both perturbation and correlation dimension analysis. Forty voice samples were classified into the proposed four types using narrowband spectrograms. Acoustic, perceptual, and correlation dimension analyses were completed for all voice samples. Perturbation measures tended to increase with voice type. Based on reliability cutoffs, the type 1 and type 2 voices were considered suitable for perturbation analysis. Measures of unreliability were higher for type 3 and 4 voices. Correlation dimension analyses increased significantly with signal type as indicated by a one-way analysis of variance. Notably, correlation dimension analysis could not quantify the type 4 voices. The proposed fourth voice type represents a subset of voices dominated by noise behavior. Current measures capable of evaluating type 4 voices provide only qualitative data (spectrograms, perceptual analysis, and an infinite correlation dimension). Type 4 voices are highly complex and the development of objective measures capable of analyzing these voices remains a topic of future investigation.

Molecular typing of methicillin-resistant Staphylococcus aureus: Comparison of PCR-based open reading frame typing, multilocus sequence typing, and Staphylococcus protein A gene typing.

PubMed

Ogihara, Shinji; Saito, Ryoichi; Sawabe, Etsuko; Kozakai, Takahiro; Shima, Mari; Aiso, Yoshibumi; Fujie, Toshihide; Nukui, Yoko; Koike, Ryuji; Hagihara, Michio; Tohda, Shuji

2018-04-01

The recently developed PCR-based open reading frame typing (POT) method is a useful molecular typing tool. Here, we evaluated the performance of POT for molecular typing of methicillin-resistant Staphylococcus aureus (MRSA) isolates and compared its performance to those of multilocus sequence typing (MLST) and Staphylococcus protein A gene typing (spa typing). Thirty-seven MRSA isolates were collected between July 2012 and May 2015. MLST, spa typing, and POT were performed, and their discriminatory powers were evaluated using Simpson's index analysis. The MRSA isolates were classified into 11, 18, and 33 types by MLST, spa typing, and POT, respectively. The predominant strains identified by MLST, spa typing, and POT were ST8 and ST764, t002, and 93-191-127, respectively. The discriminatory power of MLST, spa typing, and POT was 0.853, 0.875, and 0.992, respectively, indicating that POT had the highest discriminatory power. Moreover, the results of MLST and spa were available after 2 days, whereas that of POT was available in 5 h. Furthermore, POT is rapid and easy to perform and interpret. Therefore, POT is a superior molecular typing tool for monitoring nosocomial transmission of MRSA. Copyright © 2017 Japanese Society of Chemotherapy and The Japanese Association for Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

Water-rock interaction and geochemistry of groundwater from the Ain Azel aquifer, Algeria.

PubMed

Belkhiri, Lazhar; Mouni, Lotfi; Tiri, Ammar

2012-02-01

Hydrochemical, multivariate statistical, and inverse geochemical modeling techniques were used to investigate the hydrochemical evolution within the Ain Azel aquifer, Algeria. Cluster analysis based on major ion contents defined 3 main chemical water types, reflecting different hydrochemical processes. The first group water, group 1, has low salinity (mean EC = 735 μS/cm). The second group waters are classified as Cl-HCO(3)-alkaline earth type. The third group is made up of water samples, the cation composition of which is dominated by Ca and Mg with anion composition varying from dominantly Cl to dominantly HCO(3) plus SO(4). The varifactors obtained from R-mode FA indicate that the parameters responsible for groundwater quality variations are mainly related to the presence and dissolution of some carbonate, silicate, and evaporite minerals in the aquifer. Inverse geochemical modeling along groundwater flow paths indicates the dominant processes are the consumption of CO(2), the dissolution of dolomite, gypsum, and halite, along with the precipitation of calcite, Ca-montmorillonite, illite, kaolinite, and quartz. © Springer Science+Business Media B.V. 2011

Late Quarternary Sedimentation in the Eastern Angola Basin.

DTIC Science & Technology

1973-11-01

Angola diapir field. Illite and montmorillonite are abundant in the southern part of the basin, reflecting the source in soils of South West Africa and...northward transport in the Benguela Current system. Kaolinite dominates the clay-mineral assemblage in the north-central part of the basin

POLISHING INDUSTRIAL WASTE STREAM EFFLUENTS USING FLY ASH - NATURAL CLAY SORBENT COMBINATION

EPA Science Inventory

A laboratory evaluation of the use of acidic and basic fly ashes, bentonite, bauxite, illite, kaolinite, zeolite, vermiculite, and activated alumina is presented for polishing a 3.8 x 10 to the 6th power liters per day waste stream from the feldspar mining and processing industry...

Interactions of 14C-labeled multi-walled carbon nanotubes with soil minerals in water.

PubMed

Zhang, Liwen; Petersen, Elijah J; Zhang, Wen; Chen, Yongsheng; Cabrera, Miguel; Huang, Qingguo

2012-07-01

Carbon nanotubes are often modified to be stable in the aqueous phase by adding extensive hydrophilic surface functional groups. The stability of such CNTs in water with soil or sediment is one critical factor controlling their environmental fate. We conducted a series of experiments to quantitatively assess the association between water dispersed multi-walled carbon nanotubes (MWCNTs) and three soil minerals (kaolinite, smectite, or shale) in aqueous solution under different sodium concentrations. (14)C-labeling was used in these experiments to unambiguously quantify MWCNTs. The results showed that increasing ionic strength strongly promoted the removal of MWCNTs from aqueous phase. The removal tendency is inversely correlated with the soil minerals' surface potential and directly correlated with their hydrophobicity. This removal can be interpreted by the extended Derjaguin-Landau-Verwey-Overbeek (EDLVO) theory especially for kaolinite and smectite. Shale, which contains large and insoluble organic materials, sorbed MWCNTs the most strongly. Copyright © 2012 Elsevier Ltd. All rights reserved.

Influence of operational parameters on electro-Fenton degradation of organic pollutants from soil.

PubMed

Rosales, E; Pazos, M; Longo, M A; Sanroman, M A

2009-09-01

The combination of the Fenton's reagent with electrochemistry (the electro-Fenton process) represents an efficient method for wastewater treatment. This study describes the use of this process to clean soil or clay contaminated by organic compounds. Model soil of kaolinite clay polluted with the dye Lissamine Green B (LGB) was used to evaluate the capability of the electro-Fenton process. The effects of operating parameters such as electrode material and dye concentration were investigated. Operating in an electrochemical cell under optimized conditions while using electrodes of graphite, a constant potential difference of 5 V, pH 3, 0.2 mM FeSO(4). 7H(2)O, and electrolyte 0.1 M Na(2)SO(4), around 80% of the LGB dye on kaolinite clay was decolorized after 3 hours with an electric power consumption around 0.15 W h g(-1). Furthermore, the efficiency of this process for the remediation of a real soil polluted with phenanthrene, a typical polycyclic aromatic hydrocarbon, has been demonstrated.

In Situ Molecular Spectroscopic Evidence for CO2 Intercalation into Montmorillonite in Supercritical Carbon Dioxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loring, John S.; Schaef, Herbert T.; Turcu, Romulus VF

2012-04-25

The interaction of anhydrous supercritical CO2 (scCO2) with both kaolinite and ~1W (i.e. close to but less than one layer of hydration) calcium-saturated montmorillonite was investigated under conditions relevant to geologic carbon sequestration (50 °C and 90 bar). The CO2 molecular environment was probed in situ using a combination of three novel high-pressure techniques: X-ray diffraction, magic angle spinning nuclear magnetic resonance spectroscopy and attenuated total reflection infrared spectroscopy. We report the first direct evidence that the expansion of montmorillonite under scCO2 conditions is due to CO2 migration into the interlayer. Intercalated CO2 molecules are rotationally constrained and do notmore » appear to react with waters to form bicarbonate or carbonic acid. In contrast, CO2 does not intercalate into kaolinite. The findings show that predicting the seal integrity of caprock will have complex dependence on clay mineralogy and hydration state.« less

Mineralogy of ash of some American coals: variations with temperature and source

USGS Publications Warehouse

Mitchell, R.S.; Gluskoter, H.J.

1976-01-01

Ten samples of mineral-matter residue were obtained by the radio-frequency low-temperature ashing of subbituminous and bituminous coals. The low-temperature ash samples were then heated progressively from 400 ??C to 1400 ??C at 100 ??C intervals. Mineral phases present at each temperature interval were determined by X-ray diffraction analyses. The minerals originally present in the coals (quartz, kaolinite, illite, pyrite, calcite, gypsum, dolomite, and sphalerite) were all altered to higher temperature phases. Several of these phases, including kaolinite, metakaolinite, mullite, anhydrite, and anorthite, were found only in limited temperature ranges. Therefore the temperature of formation of the ashes in which they occur may be determined. Mineralogical differences were observed between coal samples from the Rocky Mountain Province, the Illinois Basin, and the Appalachians; and as a result of these mineralogical differences, different high-temperature phases resulted as the samples were heated. However, regional generalizations cannot be made until a greater number of samples have been studied. ?? 1976.

The Leaching of Aluminium In Spanish Clays, Coal Mining Wastes and Coal Fly Ashes by Sulphuric Acid.

NASA Astrophysics Data System (ADS)

Fernández, A. M.; Ibáñez, J. L.; Llavona, M. A.; Zapico, R.

The acid leaching of aluminium from several non traditional ores, bayerite, kaolinite, different clays, coal mining wastes and coal fly ashes, and the kinetic of their dissolution are described. The effects of time, temperature, acid concentration, sample calcination, particle size were examined. The leaching of aluminium is dependent on acid concentration and strongly on temperature. Generally, the time to reach a fixed percentage of dissolution decreases with increasing acid concentration in the range 6% to 40% acid by weight. On clays and coal mining wastes a good relation between Al removal and ratio kaolinite/illite was also observed at all temperatures and acid concentration tested. Coal fly ashes are particles that were heated at very high temperatures in the power station and Al compounds were transformed into mullite and so Al recovery was minor. Several rate equations describing the kinetics of the leach reaction were discussed and Kinetic parameters and activation energy values of samples are presented.

Numerical analysis for electrokinetic soil processing enhanced by chemical conditioning of the electrode reservoirs.

PubMed

Park, Jin-Soo; Kim, Soon-Oh; Kim, Kyoung-Woong; Kim, Byung Ro; Moon, Seung-Hyeon

2003-04-04

A numerical analysis was undertaken for enhanced electrokinetic soil processing. To perform chemical conditioning of the electrode reservoirs, the electrokinetic soil process employed a membrane as a barrier between the electrode reservoirs and the contaminated soil. An alkaline solution was purged in the anode reservoir that was bounded by the membrane. A mathematical model was used for demonstration of pH change and phenol removal from a kaolinite soil bed, the prediction of pH variations in both electrode reservoirs, and the determination of an optimized injection time of the anode-purging solution. The time-dependent dispersion coefficient was employed in consideration of the averaging effect of the velocity profile on a one-dimensional transport. The estimation of pH and phenol profiles in the soil bed reasonably agreed with the experimental data. The simulation revealed that the removal efficiency of phenol from the kaolinite soil could be improved by maintaining pH of the anode solution.

Stigma in People With Type 1 or Type 2 Diabetes

PubMed Central

Liu, Nancy F.; Brown, Adam S.; Folias, Alexandra E.; Younge, Michael F.; Guzman, Susan J.; Close, Kelly L.

2017-01-01

IN BRIEF This study quantitatively measures diabetes stigma and its associated psychosocial impact in a large population of U.S. patients with type 1 or type 2 diabetes using an online survey sent to 12,000 people with diabetes. A majority of respondents with type 1 (76%) or type 2 (52%) diabetes reported that diabetes comes with stigma. Perceptions of stigma were significantly higher among respondents with type 1 diabetes than among those with type 2 diabetes, with the highest rate in parents of children with type 1 diabetes (83%) and the lowest rate in people with type 2 diabetes who did not use insulin (49%). Our results suggest that a disturbingly high percentage of people with diabetes experience stigma, particularly those with type 1 or type 2 diabetes who are on intensive insulin therapy. The experience of stigma disproportionately affects those with a higher BMI, higher A1C, and poorer self-reported blood glucose control, suggesting that those who need the most help are also the most affected by stigma. PMID:28144043

Type of Search by Type of Library.

ERIC Educational Resources Information Center

Hafter, Ruth

1979-01-01

Summarizes the literature on users studies from the perspective that variation in type of search may be considered central to providing a rational explanation and justification of the variations in resource allocation in different types of libraries. (CWM)

The Development of a Hydroperm (Trademark) Microfiltration System for the Treatment of ’MUST’ Hospital Wastewater Effluents.

DTIC Science & Technology

1977-10-01

by pH extremes, and nonionic surfactants have been identified as bad actors" in causing membrane fouling1. Also the Hydroperm filtration technique...Talc 9. Soil (kaolinite) 10. Silver Chloride 11. Hair oil 12. Hair gel 13. Vegetable oil 14. Grease (Lard) 15. Toothpaste 16. Hair Shampoo 17

THE PHYTOAVAILABILITY OF CADMIUM TO LETTUCE IN LONG-TERM BIOSOLIDS-AMENDED SOILS

EPA Science Inventory

A field study was conducted to assess the phytoavailability of Cd in long-term biosolids-amended field plots managed at high and low pH. The experiment, established 13-15 yr prior to the present cropping, on a Christiana fine sandy loam soil (a clayey, kaolinitic, mesic Typic Pa...

Syn- and post-sedimentary controls on clay mineral assemblages in a tectonically active basin, Andean Argentinean foreland

NASA Astrophysics Data System (ADS)

Do Campo, Margarita; Nieto, Fernando; del Papa, Cecilia; Hongn, Fernando

2014-07-01

In the northern part of the Calchaquí Valley (NW Argentina), Palaeogene Andean foreland sediments are represented by a 1400-metre-thick continental succession (QLC: Quebrada de Los Colorados Formation) consisting of claystones, siltstones, sandstones, and conglomerates representing sedimentation in fluvial-alluvial plains and alluvial fan settings. To understand the main syn- and postsedimentary variables controlling the clay mineral assemblages of this succession, we have studied the fine-grained clastic sediments by X-ray diffraction and electron microscopy, along with a detailed sedimentary facies analysis, for two representative sections. In the northern section, the whole succession was sampled and analysed by XRD, whereas in the second section, a control point 15 km to the south, only the basal levels were analysed. The XRD study revealed a strong contrast in clay mineral assemblages between these two sections as well as with sections in the central Calchaquí Valley studied previously. In the northernmost part of the study area, a complete evolution from smectite at the top to R3 illite/smectite mixed-layers plus authigenic kaolinite at the bottom, through R1-type mixed-layers in between, has been recognized, indicating the attainment of late diagenesis. In contrast, the clay mineral assemblages of equivalent foreland sediments cropping out only 15 km to the south contain abundant smectite and micas, subordinate kaolinite and chlorite, and no I/S mixed-layers to the bottom of the sequence. Early diagenetic conditions were also inferred in a previous study for equivalent sediments of the QLC Formation cropping out to the south, in the central Calchaquí Valley, as smectite occurs in basal strata. Burial depths of approximately 3000 m were estimated for the QLC Formation in the central and northern Calchaquí Valley; in addition, an intermediate to slightly low geothermal gradient can be considered likely for both areas as foreland basins are regarded as

Impacts of Pantoea agglomerans strain and cation-modified clay minerals on the adsorption and biodegradation of phenanthrene.

PubMed

Tao, Kelin; Zhao, Song; Gao, Pin; Wang, Lijin; Jia, Hanzhong

2018-06-06

Interactions between microorganisms and minerals have the potential contribution to remove polycyclic aromatic hydrocarbons (PAHs) in model systems. In this study, phenanthrene (PHE) was used as a probe molecule to explore the potential adsorption and biotransformation processes in the presence of microorganisms and various reference clays, such as montmorillonite (M), kaolinite (K), and pyrophyllite (P). Equilibrium adsorption experiments and scanning electron microscopy (SEM) technique were used to investigate the sorption of Pantoea agglomerans strains on clay minerals saturated with cations (Na + and Fe 3+ ). The adsorption isotherms of PHE and Pantoea agglomerans strains on cation-modified clay minerals fitted to Langmuir equation, and their adsorbed amounts both followed the sequence: montmorillonite > kaolinite > pyrophyllite. For six types of cation-modified minerals, the behavior of PHE adsorbed and Pantoea agglomerans adhered onto mentioned minerals was in the order of Na(I)-M > Fe(Ⅲ)-M, Na(I)-K > Fe(Ⅲ)-K and Fe(Ⅲ)-P > Na(I)-P, respectively. The biodegradation results showed that cation-modified clay minerals could enhance the biodegradation of PHE, ascribing to their large specific surface area, and cation exchange capability, as well as the difference in zeta potential between minerals and Pantoea agglomerans strains. Comparison of biodegradation rates displayed that PHE was degraded the highest in the presence of Na-M (93.285%). In addition, the obtained results suggested that the adhesion of bacteria onto cation-exchanged clay minerals was beneficial to the biodegradation of PHE. Anthracen-9-ylmethanol and 3,4-dimethyl-2-(3-methylbutanoyl)benzoic acid were detected as the main intermediate compounds, which can be further biodegraded into small molecules. The overall results obtained in this study are of valuable significance for the understanding of the behavior of PHE in soil and associated environment. Copyright © 2018 Elsevier Inc. All

Rehabilitation of adobe buildings. Understanding different materials from Portugal

NASA Astrophysics Data System (ADS)

Costa, Cristiana; Rocha, Fernando; Velosa, Ana

2016-04-01

Earth construction is the oldest building material known, with documented cases of the use of earth bricks since Mesopotamia around 10 000 BC (Heathcote, 1995). The earth construction exists throughout the majority of the world in different cultures, and for some countries, nowadays it continues to be the main process of construction (Vega et al, 2011). Around 30% of the world's population lives in buildings made of earth materials. Earthen construction is an environmentally friendly technique with a social and cultural contribution; this advantage is increased when this type of construction is applied in developing countries where the material costs counterbalance with labour costs, and where other materials and techniques cannot be available (Ciancio et al, 2013). Studies of materials characterization are required in order to understand the composition and specific properties of the earth buildings, their heterogeneity and their degradation mechanisms. Some adobes from different buildings, ages and regions of Portugal were collected in order to characterize them (mineralogically, chemically and physically). It was possible to understand the composition of these materials and their differences. Main minerals are quartz, feldspars, calcite and phyllosilicates (mica and kaolinite). The mechanical behaviour of these materials isn't the best, but it is possible to improve it with some simple and cheap natural additives (kaolinitic soils). The characterization of these materials allows us to understand the differences between the materials from the different regions (controlled by locally available raw materials). Understanding these materials, and their properties, it is possible to formulate new ones for repair, conservation and rehabilitation works. The adobe bricks are an alternative of kiln baked bricks which has several advantages and one of the most important is that these materials are recyclable. Adobes are an excellent option for building rehabilitation, if

Soil Minerals Affect Extracellular Enzyme Activities in Cold and Warm Environments

NASA Astrophysics Data System (ADS)

Yang, Z.; Morin, M. M.; Graham, D. E.; Wullschleger, S. D.; Gu, B.

2017-12-01

Extracellular enzymes are mainly responsible for degrading and cycling soil organic matter (SOM) in both cold and warm terrestrial ecosystems. Minerals can play important roles in affecting soil enzyme activities, however, the interactions between enzyme and soil minerals remain poorly understood. In this study, we developed a model soil-enzyme system to examine the mineral effects on a hydrolytic enzyme (i.e., β-glucosidase) under both cold (4°C) and relatively warm (20 and 30°C) conditions. Minerals including iron oxides and clays (e.g., kaolinite and montmorillonite) were used to mimic different types of soils, and enzyme adsorption experiments were conducted to determine the enzyme interactions with different mineral surfaces. Time-series experiments were also carried out to measure enzymatic degradation of the organic substrates, such as cellobiose and indican. We observed that fractions of adsorbed enzyme and the hydrolytic activity were higher on iron oxides (e.g., hematite) compared to kaolinite and montmorillonite at given experimental conditions. The degradation of cellobiose was significantly faster than that of indican in the presence of minerals. We also found that the adsorption of enzyme was not dependent on the mineral surface areas, but was controlled by the mineral surface charge. In addition, temperature increase from 4 to 30°C enhanced mineral-assisted glucosidase hydrolysis by 2 to 4 fold, suggesting greater degradation under warmer environments. The present work demonstrates that the enzyme activity is influenced not only by the soil temperature but also by the surface chemistry of soil minerals. Our results highlight the need to consider the physical and chemical properties of minerals in biogeochemical models, which could provide a better prediction for enzyme-facilitated SOM transformations in terrestrial ecosystems.

On the mineral characteristics and geochemistry of the Florida phosphate of Four Corners and Hardee County mines

NASA Astrophysics Data System (ADS)

Baghdady, Ashraf R.; Howari, Fares M.; Al-Wakeel, Mohamed I.

2016-08-01

The Florida phosphate deposits in Four Corners and Hardee County mines are composed mainly of phosphate minerals and quartz in addition to subordinate proportions of feldspars, dolomite, calcite, gypsum, kaolinite, attapulgite and montmorillonite. These phosphorites contain three structurally different types of mudclasts: massive mudclasts, mudclasts with concentric structure and mudclasts consisting of agglomerates of apatite microparticles. The latter are represented by particles resembling phosphatized fossil bacteria associated with microbial filaments, and hollow apatite particles having surfacial coatings and connected to microbial filaments. The Florida phosphate particles are reworked and vary in mineral composition, color and shape. They are composed of a mixture of well-crystalline species including carbonate fluorapatite (francolite), carbonate apatite and fluorapatite. The color variation of the phosphate particles is related to difference in mineral composition, extent of diagenetic effects and reworking. The light-colored mudclasts are characterized by the presence of carbonate apatite and aluminum hydroxide phosphate minerals, whereas the dark mudclasts are rich in iron aluminum hydroxide phosphate minerals. The Florida phosphorites are suggested to be formed partially by authigenetic precipitation, replacement of the sea floor carbonate and diatomite, and microbial processes. With respect to elemental geochemistry, the analyzed particles contain small percentages of sulfur and iron which are related to the occurrence of pyrite. Traces of silica and alumina are recorded which may be attributed to the diagenetic. Some of the tested particles are relatively rich in phosphorous, fluorine, calcium, and magnesium, while poor in silicon, potassium and sulfur. Whereas, the bioclasts (especially teeth) are relatively rich in calcium, phosphorous and fluorine while poor in silicon, aluminum, magnesium and potassium. Hence, the microchemical analyses revealed

Who's on first? Part I: Influence of plant growth on C association with fresh soil minerals

NASA Astrophysics Data System (ADS)

Neurath, R.; Whitman, T.; Nico, P. S.; Pett-Ridge, J.; Firestone, M. K.

2015-12-01

Mineral surfaces provide sites for carbon stabilization in soils, protecting soil organic matter (SOM) from microbial degradation. SOM distributed across mineral surfaces is expected to be patchy and certain minerals undergo re-mineralization under dynamic soil conditions, such that soil minerals surfaces can range from fresh to thickly-coated with SOM. Our research investigates the intersection of microbiology and geochemistry, and aims to build a mechanistic understanding of plant-derived carbon (C) association with mineral surfaces and the factors that determine SOM fate in soil. Plants are the primary source of C in soil, with roots exuding low-molecular weight compounds during growth and contributing more complex litter compounds at senescence. We grew the annual grass, Avena barbata, (wild oat) in a 99 atom% 13CO2 atmosphere in soil microcosms incubated with three mineral types representing a spectrum of reactivity and surface area: quartz, kaolinite, and ferrihydrite. These minerals, isolated in mesh bags to exclude roots but not microorganisms, were extracted and analyzed for total C and 13C at multiple plant growth stages. At plant senescence, the quartz had the least mineral-bound C (0.40 mg-g-1) and ferrihydrite the most (0.78 mg-g-1). Ferrihydrite and kaolinite also accumulated more plant-derived C (3.0 and 3.1% 13C, respectively). The experiment was repeated with partially digested 13C-labled root litter to simulate litter decomposition during plant senescence. Thus, we are able evaluate contributions derived from living and dead root materials on soil minerals using FTIR and 13C-NMR. We find that mineral-associated C bears a distinct microbial signature, with soil microbes not only transforming SOM prior to mineral association, but also populating mineral surfaces over time. Our research shows that both soil mineralogy and the chemical character of plant-derived compounds are important controls of mineral protection of SOM.

Nonlinear Propagation of Sound in Recently Settled Flocculated Sediments

NASA Astrophysics Data System (ADS)

Reed, A. H.; Sanders, W. M.

2016-12-01

Cohesive sediments undergo changes in a whirlwind. Dumped out of the river and into the estuary, they get bathed in salty water and subject to turbulent motion. During this sequence of events, the clay particles form clay aggregates of larger size with higher settling rates than the clay particles. Once the flocs have settled, cohesive sediments may form a sediment deposit of mud. Our interest is in the factors that control the development of soundspeed within these muds. This paper addresses organic matter influences on floc aggregation and settling rates. In laboratory studies, organic matter type differed in mixtures with either bentonite or kaolinite clays. The organic matter types used were guar gum, a net positive biopolymer, and xanthan gum, a net negative biopolymer derived from bacterial exudates, similar to those commonly found in estuaries. These biopolymers were dissolved into low salinity water (0-10 ppt). The biopolymer mixture was degassed and during the degassing process, either bentonite or kaolinite clay was added to the vessel. Surprisingly, different settling rates occurred in the clay-biopolymer mixtures. The settling rates of the clay-guar mixtures was more rapid (1-2 days) than the settling rate for the clay-xanthan mixtures. While clay-guar consolidated further, clay-xanthan maintained consistency for more than 2 weeks with density slowly increasing during that period. Compressional soundspeed (Vp) measurements were made with depth through the vessel using 0.5 mHz piezoelectric transducers. It was found that Vp in water was similar to that of the clay-xanthan. Vp was the same in the upper 6 cm of mud as it was in the overlying water and Vp decreased to become slower with increasing depth. Compressional wave velocity (Vp) also changed slightly with the guar complexes below the sediment water interface to the depth of the vessel. Vp was slightly slower in the mud than in the water column. Vp of the water was 1480-1495 m/s whereas Vp within the

Epithermal uranium deposits in a volcanogenic context: the example of Nopal 1 deposit, Sierra de Pena Blanca, Mexico

NASA Astrophysics Data System (ADS)

Calas, G.; Angiboust, S.; Fayek, M.; Camacho, A.; Allard, T.; Agrinier, P.

2009-12-01

The Peña Blanca molybdenum-uranium field (Chihuahua, Mexico) exhibits over 100 airborne anomalies hosted in tertiary ignimbritic ash-flow tuffs (44 Ma) overlying the Pozos conglomerate and a sequence of Cretaceous carbonate rocks. Uranium occurrences are associated with breccia zones at the intersection of two or more fault systems. Periodic reactivation of these structures associated with Basin and Range and Rio Grande tectonic events resulted in the mobilization of U and other elements by meteoric fluids heated by geothermal activity. Trace element geochemistry (U, Th, REE) provides evidence for local mobilization of uranium under oxidizing conditions. In addition, O- and H-isotope geochemistry of kaolinite, smectite, opal and calcite suggests that argillic alteration proceeded at shallow depth with meteoric water at 25-75 °C. Focussed along breccia zones, fluids precipitated several generations of pyrite and uraninite together with kaolinite, as in the Nopal 1 mine, indicating that mineralization and hydrothermal alteration of volcanic tuffs are contemporaneous. Low δ34S values (~ -24.5 ‰) of pyrites intimately associated with uraninite suggest that the reducing conditions at the origin of the U-mineralization arise from biological activity. Later, the uplift of Sierra Pena Blanca resulted in oxidation and remobilization of uranium, as confirmed by the spatial distribution of radiation-induced defect centers in kaolinites. These data show that tectonism and biogenic reducing conditions can play a major role in the formation and remobilization of uranium in epithermal deposits. By comparison with the other uranium deposits at Sierra Pena Blanca and nearby Sierra de Gomez, Nopal 1 deposit is one of the few deposits having retained a reduced uranium mineralization.

Experimental study of Human Adenoviruses interactions with clays

NASA Astrophysics Data System (ADS)

Bellou, Maria; Syngouna, Vasiliki; Paparrodopoulos, Spyros; Vantarakis, Apostolos; Chrysikopoulos, Constantinos

2014-05-01

Clays are used to establish low permeability liners in landfills, sewage lagoons, water retention ponds, golf course ponds, and hazardous waste sites. Human adenoviruses (HAdVs) are waterborne viruses which have been used as viral indicators of fecal pollution. The objective of this study was to investigate the survival of HAdV in static and dynamic clay systems. The clays used as a model were crystalline aluminosilicates: kaolinite and bentonite. The adsorption and survival of HAdVs onto these clays were characterized at two different controlled temperatures (4 and 25o C) under static and dynamic batch conditions. Control tubes, in the absence of clay, were used to monitor virus inactivation due to factors other than adsorption to clays (e.g. inactivation or sorption onto the tubes walls). For both static and dynamic batch experiments, samples were collected for a maximum period of seven days. This seven day time - period was determined to be sufficient for the virus-clay systems to reach equilibrium. To infer the presence of infectious HAdV particles, all samples were treated with Dnase and the extraction of viral nucleid acid was performed using a commercial viral RNA kit. All samples were analyzed by Real - Time PCR which was used to quantify viral particles in clays. Samples were also tested for virus infectivity by A549 cell cultures. Exposure time intervals in the range of seven days (0.50-144 hours) resulted in a load reduction of 0.74 to 2.96 logs for kaolinite and a reduction of 0.89 to 2.92 for bentonite. Furthermore, virus survival was higher onto bentonite than kaolinite (p

Quantifying mineral abundances of complex mixtures by coupling spectral deconvolution of SWIR spectra (2.1-2.4 μm) and regression tree analysis

USGS Publications Warehouse

Mulder, V.L.; Plotze, Michael; de Bruin, Sytze; Schaepman, Michael E.; Mavris, C.; Kokaly, Raymond F.; Egli, Markus

2013-01-01

This paper presents a methodology for assessing mineral abundances of mixtures having more than two constituents using absorption features in the 2.1-2.4 μm wavelength region. In the first step, the absorption behaviour of mineral mixtures is parameterised by exponential Gaussian optimisation. Next, mineral abundances are predicted by regression tree analysis using these parameters as inputs. The approach is demonstrated on a range of prepared samples with known abundances of kaolinite, dioctahedral mica, smectite, calcite and quartz and on a set of field samples from Morocco. The latter contained varying quantities of other minerals, some of which did not have diagnostic absorption features in the 2.1-2.4 μm region. Cross validation showed that the prepared samples of kaolinite, dioctahedral mica, smectite and calcite were predicted with a root mean square error (RMSE) less than 9 wt.%. For the field samples, the RMSE was less than 8 wt.% for calcite, dioctahedral mica and kaolinite abundances. Smectite could not be well predicted, which was attributed to spectral variation of the cations within the dioctahedral layered smectites. Substitution of part of the quartz by chlorite at the prediction phase hardly affected the accuracy of the predicted mineral content; this suggests that the method is robust in handling the omission of minerals during the training phase. The degree of expression of absorption components was different between the field sample and the laboratory mixtures. This demonstrates that the method should be calibrated and trained on local samples. Our method allows the simultaneous quantification of more than two minerals within a complex mixture and thereby enhances the perspectives of spectral analysis for mineral abundances.

Formation of copper aluminate spinel and cuprous aluminate delafossite to thermally stabilize simulated copper-laden sludge.

PubMed

Hu, Ching-Yao; Shih, Kaimin; Leckie, James O

2010-09-15

The study reported herein indicated the stabilization mechanisms at work when copper-laden sludge is thermally treated with gamma-alumina and kaolinite precursors, and evaluated the prolonged leachability of their product phases. Four copper-containing phases - copper oxide (CuO), cuprous oxide (Cu(2)O), copper aluminate spinel (CuAl(2)O(4)), and cuprous aluminate delafossite (CuAlO(2)) - were found in the thermal reactions of the investigated systems. These phases were independently synthesized for leaching by 0.1M HCl aqueous solution, and the relative leachabilities were found to be CuAl(2)O(4)kaolinite had a lower incorporation capability than gamma-alumina, it was found to transform a considerable amount of copper into CuAl(2)O(4) between 950 and 1000 degrees C. At higher temperatures, CuAlO(2) was produced only in the gamma-alumina system as the occurrence of Cu(2)O-cristobalite solution in the kaolinite system precluded the production of CuAlO(2). The hypothesis that the spinel formation mechanism has two stages was supported by the results of the changing Cu/Al mole ratio in the system, and the rate-limiting step was identified as the diffusion process in the second stage. Copyright 2010 Elsevier B.V. All rights reserved.

Subsidence problems related to the development of siliciclastic karst on the Citronelle Formation of southwestern Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Isphording, W.C.; Flowers, G.C.

1985-01-01

The irreversible transformation of kaolinite to gibbsite and the concomitant negative volume change associated with the reaction has resulted in residential structural damage in Mobile, Alabama. Failure of the insurance company to honor damage resulting from a sinkhole collapse clause resulted in litigation. The main points of contention in the trial were: (1) were the small depressions in the owner's yard caused by dissolution of material, resulting in the formation of subteranean voids., (2) does the language used in the policy, i.e., We cover for damages caused by sinkhole collapse due to the dissolution of limestone or similar rock formations,more » mean that because the Citronelle Sand is a rock formation that the resident should recover for damage to his house. Evidence introduced for the plaintiff included x-ray diffractograms, SEM photographs and grain size analyses. A summary of literature on the development of karst in non-carbonate terranes was also produced x-ray diffractograms indicated that gibbsite was being formed in the vadose zone; SEM photographs clearly revealed the presence of euhedral gibbsite crystals on both quartz grains and kaolinite. Size analyses were offered to disprove the allegation that the subsidence was a piping effect caused solely by removal of the silt component. Mass-balance equations and chemical analyses of groundwater were used to demonstrate that not only was kaolinite altering to gibbsite, causing loss of volume, but that some quartz was also being taken into solution. After consideration of the evidence, the jury found in favor of the plaintiff and the resident was compensated for damage.« less

Clay mineralogical record on the upper continental slope of the northwestern South China Sea since the Last Glacial Maximum

NASA Astrophysics Data System (ADS)

CHEN, Q.; Liu, Z.; Stattegger, K.

2012-12-01

Clay mineralogy of two gravity cores (18428 and 18429) on the upper continental slope of the northwestern South China Sea was investigated in order to understand terrigenous sediment sources and to evaluate the contribution from the Red River since the Late Glacial Maximum. Planktonic foraminiferal oxygen isotope and carbonate stratigraphies suggest that Core 18428 is constrained in Holocene while Core 18429 covers the period of MIS 1-2. Clay mineral assemblages of two cores are composed mainly of smectite (18-57%) and illite (21-41%), with minor chlorite (12-21%) and kaolinite (8-26%). In despite of relatively constant values of illite crystallinity, ranging among 0.14°-0.20° Δ2θ, the time series variation in clay mineral distributions indicates a strong glacial-interglacial shift. Contents of illite, chlorite, and kaolinite (Core 18429) in the Holocene are lower than in the glacial period, and vice versa for the smectite content. The provenance analysis based on clay mineralogy suggests the Red River as a predominant sedimentary source of illite, chlorite, and kaolinite during all the depositional period of MIS 1-2. The sea level change actually controlled the variations of clay mineral assemblages on the upper slope since the Last Glacial Maximum. When the sea level was low during the last glacial period, more terrigenous sediments from the Red River could reach the continental slope in the northwestern South China Sea. However, when the sea level is closed to the present situation during the Holocene, most of Red River sediments could be trapped in the Gulf of Tonkin, instead of draining in the deep South China Sea.

Assessment of cement kiln dust (CKD) for stabilization/solidification (S/S) of arsenic contaminated soils.

PubMed

Moon, Deok Hyun; Wazne, Mahmoud; Yoon, In-Ho; Grubb, Dennis G

2008-11-30

A stabilization/solidification (S/S) process for arsenic (As) contaminated soils was evaluated using cement kiln dust (CKD). Laboratory-prepared slurries, made of either kaolinite or montmorillonite, and field soils spiked with either As(3+) or As(5+) were prepared and treated with CKD ranging from 10 to 25 wt%. Sodium arsenite and sodium arsenate at 0.1 wt% were used to simulate arsenite (As(3+)) and arsenate (As(5+)) source contamination in soils, respectively. The effectiveness of treatment was evaluated at curing periods of 1- and 7-days based on the toxicity characteristic leaching procedure (TCLP). As-CKD and As-clay-CKD slurries were also spiked at 10 wt% to evaluate As immobilization mechanism using X-ray powder diffraction (XRPD) analyses. Overall, the TCLP results showed that only the As(5+) concentrations in kaolinite amended with 25 wt% CKD after 1 day of curing were less than the TCLP regulatory limit of 5mg/L. Moreover, at 7 days of curing, all As(3+) and As(5+) concentrations obtained from kaolinite soils were less than the TCLP criteria. However, none of the CKD-amended montmorillonite samples satisfied the TCLP-As criteria at 7 days. Only field soil samples amended with 20 wt% CKD complied with the TCLP criteria within 1 day of curing, where the source contamination was As(5+). XRPD and scanning electron microscopy (SEM)-energy dispersive X-ray spectroscopy (EDX) results showed that Ca-As-O and NaCaAsO(4).7.5H(2)O were the primary phases responsible for As(3+) and As(5+) immobilization in the soils, respectively.

Blood Types

MedlinePlus

... only get a transfusion with O blood. Type O-negative blood can be given to people with any blood type. That's because it has none of the markers that can set off a reaction. People with this blood type are considered "universal donors" and are in great demand at blood banks. ...

Phage typing or CRISPR typing for epidemiological surveillance of Salmonella Typhimurium?

PubMed

Mohammed, Manal

2017-11-07

Salmonella Typhimurium is the most dominant Salmonella serovar around the world. It is associated with foodborne gastroenteritis outbreaks but has recently been associated with invasive illness and deaths. Characterization of S. Typhimurium is therefore very crucial for epidemiological surveillance. Phage typing has been used for decades for subtyping of S. Typhimurium to determine the epidemiological relation among isolates. Recent studies however have suggested that high throughput clustered regular interspaced short palindromic repeats (CRISPR) typing has the potential to replace phage typing. This study aimed to determine the efficacy of high-throughput CRISPR typing over conventional phage typing in epidemiological surveillance and outbreak investigation of S. Typhimurium. In silico analysis of whole genome sequences (WGS) of well-documented phage types of S. Typhimurium reveals the presence of different CRISPR type among strains belong to the same phage type. Furthermore, different phage types of S. Typhimurium share identical CRISPR type. Interestingly, identical spacers were detected among outbreak and non-outbreak associated DT8 strains of S. Typhimurium. Therefore, CRISPR typing is not useful for the epidemiological surveillance and outbreak investigation of S. Typhimurium and phage typing, until it is replaced by WGS, is still the gold standard method for epidemiological surveillance of S. Typhimurium.

Phosphates in some Missouri refractory clays

USGS Publications Warehouse

Halley, Robert B.; Foord, Eugene E.; Keller, David J.; Keller, Walter D.

1997-01-01

This paper describes in detail phosphate minerals occurring in refractory clays of Missouri and their effect on the refractory degree of the clays. The minerals identified include carbonate-fluorapatite (francolite), crandallite, goyazite, wavellite, variscite and strengite. It is emphasized that these phosphates occur only in local isolated concentrations, and not generally in Missouri refractory clays.The Missouri fireclay region comprises 2 districts, northern and southern, separated by the Missouri River. In this region, clay constitutes a major part of the Lower Pennsylvanian Cheltenham Formation. The original Cheltenham mud was an argillic residue derived from leaching and dissolution of pre-Pennsylvanian carbonates. The mud accumulated on a karstic erosion surface truncating the pre-Cheltenham rocks. Fireclays of the northern district consist mainly of poorly ordered kaolinite, with variable but minor amounts of illite, chlorite and fine-grained detrital quartz. Clays of the southern district were subjected to extreme leaching that produced well-ordered kaolinite flint clays. Local desilication formed pockets of diaspore, or more commonly, kaolinite, with oolite-like nubs or burls of diaspore (“burley”" clay).The phosphate-bearing materials have been studied by X-ray diffraction (XRD), scanning electron microscopy-energy dispersive spectral analysis (SEM-EDS) and chemical analysis. Calcian goyazite was identified in a sample of diaspore, and francolite in a sample of flint clay. A veinlet of wavellite occurs in flint clay at one locality, and a veinlet of variscite-strengite at another locality.The Missouri flint-clay-hosted francolite could not have formed in the same manner as marine francolite. The evidence suggests that the Cheltenham francolite precipitated from ion complexes in pore water, nearly simultaneously with crystallization of kaolinite flint clay from an alumina-silica gel. Calcian goyazite is an early diagenetic addition to its diaspore

Solar Type II Radio Bursts and IP Type II Events

NASA Technical Reports Server (NTRS)

Cane, H. V.; Erickson, W. C.

2005-01-01

We have examined radio data from the WAVES experiment on the Wind spacecraft in conjunction with ground-based data in order to investigate the relationship between the shocks responsible for metric type II radio bursts and the shocks in front of coronal mass ejections (CMEs). The bow shocks of fast, large CMEs are strong interplanetary (IP) shocks, and the associated radio emissions often consist of single broad bands starting below approx. 4 MHz; such emissions were previously called IP type II events. In contrast, metric type II bursts are usually narrowbanded and display two harmonically related bands. In addition to displaying complete dynamic spectra for a number of events, we also analyze the 135 WAVES 1 - 14 MHz slow-drift time periods in 2001-2003. We find that most of the periods contain multiple phenomena, which we divide into three groups: metric type II extensions, IP type II events, and blobs and bands. About half of the WAVES listings include probable extensions of metric type II radio bursts, but in more than half of these events, there were also other slow-drift features. In the 3 yr study period, there were 31 IP type II events; these were associated with the very fastest CMEs. The most common form of activity in the WAVES events, blobs and bands in the frequency range between 1 and 8 MHz, fall below an envelope consistent with the early signatures of an IP type II event. However, most of this activity lasts only a few tens of minutes, whereas IP type II events last for many hours. In this study we find many examples in the radio data of two shock-like phenomena with different characteristics that occur simultaneously in the metric and decametric/hectometric bands, and no clear example of a metric type II burst that extends continuously down in frequency to become an IP type II event. The simplest interpretation is that metric type II bursts, unlike IP type II events, are not caused by shocks driven in front of CMEs.

Concurrent vaccination of boars with type 1 and type 2 porcine reproductive and respiratory syndrome virus (PRRSV) reduces seminal shedding of type 1 and type 2 PRRSV

PubMed Central

Jeong, Jiwoon; Park, Changhoon; Kang, Ikjae; Park, Su-Jin; Chae, Chanhee

2017-01-01

The objective of the present study was to determine the effect of concurrent vaccination of boars with type 1 and type 2 porcine reproductive and respiratory syndrome virus (PRRSV) on seminal shedding of both genotypes. The boars tolerated well concurrent administration of 2 commercial PRRSV vaccines, and no adverse reactions were observed. No interference in the humoral immune response (measured as the level of anti-PRRSV antibodies) or the cell-mediated immune response (measured as the level of PRRSV-specific interferon-γ-secreting cells) was observed after concurrent administration compared with single administration of the same vaccines. Concurrent vaccination significantly reduced the load of type 1 and type 2 PRRSV in blood and semen after singular (type 1 or type 2) and dual (type 1 and type 2) PRRSV challenge, and it did not significantly affect the efficacy of each vaccine. The results demonstrate that concurrent vaccination of boars with type 1 and type 2 PRRSV reduces shedding of both genotypes in semen. PMID:28408778

Refinement Types ML

DTIC Science & Technology

1994-03-16

105 2.10 Decidability ........ ................................ 116 3 Declaring Refinements of Recursive Data Types 165 3.1...However, when we introduce polymorphic constructors in Chapter 5, tuples will become a polymorphic data type very similar to other polymorphic data types...terminate. 0 Chapter 3 Declaring Refinements of Recursive Data Types 3.1 Introduction The previous chapter defined refinement type inference in terms of

Critical Differences between the Type-A Prone and Type-A Personalitites.

ERIC Educational Resources Information Center

Cassel, Russell N.; Cassel, Susie L.

1984-01-01

Type-A Prone and Type-A personalities were assessed on the basis of the Cassel Type-A Personality Assessment Profile. Statistical data analysis indicated differences in positive lifestyle, blood pressure, and self-control and no differences in negative lifestyle, pulse rate, or peripheral temperature. Type-A Prone and Type-A norm profiles were…

Thermal Properties of Soils

DTIC Science & Technology

1981-12-01

plagio - clase feldspar and pyroxene. The tine fraction may Surface area and its effects contain the clay "sheet" minerals (i.e. kaolinite. illite...Pyroxene, Kaoliniwe Unified By By Ortho. Plagio . amphibole, Basic clay min. Hematite Soil Soil soil petrogr. X.ray clase clase and Igneous and clay and no

Exploration for gold mineralization in the Arabo Nubian Shield: Using remote sensing Approach

NASA Astrophysics Data System (ADS)

Ramadan, Talaat

2013-04-01

In the southern part of the Eastern Desert of Egypt, Landsat Thematic Mapper (ETM+) data and fieldwork was combined with mineralogical and geochemical investigations in order to detect and characterize alteration zones within Pan-African rocks. The processing of Landsat ETM+ data using ratioing (bands 5/7,5/1,4/3 in Red, Green, Blue) showed two different types of alteration zones (type l and 2). Type 1 is close to the ophiolitic ultramafic rocks and type 2 is located within island-arc related metavolcanic rocks at the study areas. Both of these alteration zones are concordant with the main NW-SE structural trend. Mineralogical studies indicate that the alteration zones of type 1 consist mainly of calcite, ankerite, magnesite, dolomite and quartz. Chromian spinel, pyrite, and Ni-bearing sulphides (gersdorffite, pentlandite and polydymite) are the main ore minerals within this zone. Alteration zones of type 2 are strongly potassium-enriched and pyrophyllite, kaolinite, illite, gypsum and quartz occur. The brecciated quartz-veins associated with theses alteration zones consist of quartz, Fe-hydroxides, hematite and native gold. The gold content reaches up to 5 g/t in the alteration zone, while it extends up to 50 g/t in the quartz veins. This study presents a mineralogical characterization of such zones and demonstrates the utility of orbital remote sensing for finding unknown alteration zones in the Eastern Desert and other arid areas with similar host rock lithologies.

Type 1 or Type 2 Diabetes and Pregnancy

MedlinePlus

... and Pregnancy Articles Type 1 or Type 2 Diabetes and Pregnancy Language: English (US) Español (Spanish) Recommend on Facebook Tweet Share Compartir Problems of Diabetes in Pregnancy Blood sugar that is not well ...

Discriminating the reaction types of plant type III polyketide synthases

PubMed Central

Shimizu, Yugo; Ogata, Hiroyuki; Goto, Susumu

2017-01-01

Abstract Motivation: Functional prediction of paralogs is challenging in bioinformatics because of rapid functional diversification after gene duplication events combined with parallel acquisitions of similar functions by different paralogs. Plant type III polyketide synthases (PKSs), producing various secondary metabolites, represent a paralogous family that has undergone gene duplication and functional alteration. Currently, there is no computational method available for the functional prediction of type III PKSs. Results: We developed a plant type III PKS reaction predictor, pPAP, based on the recently proposed classification of type III PKSs. pPAP combines two kinds of similarity measures: one calculated by profile hidden Markov models (pHMMs) built from functionally and structurally important partial sequence regions, and the other based on mutual information between residue positions. pPAP targets PKSs acting on ring-type starter substrates, and classifies their functions into four reaction types. The pHMM approach discriminated two reaction types with high accuracy (97.5%, 39/40), but its accuracy decreased when discriminating three reaction types (87.8%, 43/49). When combined with a correlation-based approach, all 49 PKSs were correctly discriminated, and pPAP was still highly accurate (91.4%, 64/70) even after adding other reaction types. These results suggest pPAP, which is based on linear discriminant analyses of similarity measures, is effective for plant type III PKS function prediction. Availability and Implementation: pPAP is freely available at ftp://ftp.genome.jp/pub/tools/ppap/ Contact: goto@kuicr.kyoto-u.ac.jp Supplementary information: Supplementary data are available at Bioinformatics online. PMID:28334262

Multidecadal persistence of organic matter in soils: insights from spatially resolved investigations at the submicrometer scale

NASA Astrophysics Data System (ADS)

Lutfalla, Suzanne; Barré, Pierre; Bernard, Sylvain; Le Guillou, Corentin; Alléon, Julien; Chenu, Claire

2016-04-01

Better understanding the mechanisms responsible for the pluri-decadal persistence of carbon in soils requires well constraining the dynamics, the distribution and the chemical nature of both the soil organic carbon (SOC) and the associated mineral phases. The question we address in this work is whether different mineral species lead to different organo-mineral interactions and stabilize different quantities of SOM and different types of SOC. Here, benefiting from the unique opportunity offered by an INRA long term bare fallow (LTBF) experiment having started in 1928 in Versailles (France), we report the in-situ characterization of SOC dynamics in four clay fractions of this silty loam soil (total clays [TC, <2μm], coarse clays [CC, 0.2-2μm], intermediate clays [IC, 0.05-0.2μm] and fine clays [FC, 0-0.05μm]). The IC and FC fractions only contain smectite and illite/smectite mixed-layered clay minerals while the CC fraction also contains illite and kaolinite. In the absence of any carbon input, the plant-free LTBF clay fractions from Versailles progressively lost SOC during the first 50 years of the experiment, until they reached a seemingly stable concentration. Of note, the investigated clay fractions did not lose the same amount of SOC and do not exhibit the same final carbon concentrations. The decrease of the organic C:N ratios with LTBF duration corresponds to a progressive enrichment in N-rich SOC for all fractions which can be attributed to microbial material. Even though the speciation of SOC appears to only slightly evolve with LTBF duration, an enrichment in carboxyl and carbonyl groups is revealed by bulk-scale C-NEXAFS data for SOC from all clay fractions. In addition, STXM-based NEXAFS investigations at the submicrometer scale reveal three types of SOC-clay assemblages in addition to clay-free SOC and organic-free clays. While SOC appears mostly adsorbed onto clay surfaces within the IC and FC fractions, other protection mechanisms occur within the

Differing causes of pregnancy loss in type 1 and type 2 diabetes.

PubMed

Cundy, Tim; Gamble, Greg; Neale, Leonie; Elder, Rose; McPherson, Paul; Henley, Patrick; Rowan, Janet

2007-10-01

Women with type 2 and type 1 diabetes have differing risk factors for pregnancy loss. We compared the rates and causes of pregnancy loss in women with type 1 and type 2 diabetes. We utilized prospectively collected data on all pregnancies in a 20-year period (1986-2005) from a single center with a high prevalence of type 2 diabetes. Pregnancy losses included terminations for medical reasons and deaths up to 1 month postpartum but not spontaneous pregnancy losses <20 weeks' gestation. There were 870 pregnancies in women with known diabetes (330 with type 1 and 540 with type 2 diabetes) and 325 in women with diabetes diagnosed in pregnancy but persisting postpartum (97% type 2 diabetes). The rate of pregnancy loss was similar in type 1 and type 2 diabetes (2.6 vs. 3.7%, P = 0.39), but the causes of pregnancy loss differed. In type 1 diabetes >75% were attributable to major congenital anomalies or prematurity; in type 2 diabetes >75% were attributable to stillbirth or chorioamnionitis (P = 0.017). Women with type 2 and type 1 diabetes had similar A1C at presentation and near term, but the former were older (P < 0.001) and more obese (P < 0.0001). There are significant differences in the main causes of pregnancy loss in women with type 1 and type 2 diabetes. The higher rates of stillbirth in women with type 2 diabetes, suggest that other features, such as obesity, contribute significantly to pregnancy losses.

Thinking about gender types: cognitive organization of female and male types.

PubMed

Vonk, Roos; Ashmore, Richard D

2003-06-01

We examined the content and dimensional structure of a large and representative sample of gender types. In Study 1, using an open-ended procedure, participants generated 306 different labels for female types (e.g. housewife, feminist, femme fatale, secretary, slob) and 310 for male types (e.g. workaholic, family man, sissy, womanizer, labourer). In Study 2A, a multidimensional configuration of 229 of these male and female types was derived from a free sorting task among a new set of participants. In Study 2B, a subset of types was judged on several dimensions of meaning, which were then fitted into the configuration of types. The most important dimensions in describing the structure of gender types were: young-old, masculine-feminine and traditional-modern. The masculine-feminine dimension showed that the male and female types were largely separated from each other; within each gender category, the types were ordered by their position on the masculine-feminine dimension. Several other aspects of current thinking about men and women are discussed.

Mineralogy and crystal chemistry of iron in the Timan bauxite and products of their technological processing

NASA Astrophysics Data System (ADS)

Kotova, O.; Silaev, V.; Lutoev, V.; Vakhrushev, A.

2016-04-01

Mineralogical and geochemical features of two series of samples of typical bauxites from two deposits of Middle Timan mining area (Vezhayu-Vorykva and Svetlinskoe) were studied. The phase composition of ferrous bauxites generally is boehmite, hematite, ultradisperse low-ordered goethite and berthierine. In a boehmite and kaolinite structural impurity of iron to 10%, and in the iron oxidehydroxides aluminum impurity is revealed. On iron content bauxites are subdivided into three mineral types for which quantitative data on valence states of ions of iron and proportions of their distribution last on nonequivalent structural positions in hematite, goethite and berthierine are obtained. Noble metals (Ag, Au, Ir, Rh, Pd) concentrating in bauxites are revealed for the first time. Obtained data can lead to decrease of power consumption during aluminum production and high quality ceramics, to provide production of valuable iron oxide, and also to minimize the ecological harm from accumulation of bauxite wastes.

Comment on "A spectroscopic comparison of selected Chinese kaolinite, coal bearing kaolinite and halloysite--a mid-infrared and near-infrared study" and "Infrared and infrared emission spectroscopic study of typical Chinese kaolinite and halloysite" by Hongfei Cheng et al. (2010).

PubMed

Kloprogge, J Theo

2015-02-05

In two papers Cheng et al. (2010) reported in this journal on the mid-infrared, near-infrared and infrared emission spectroscopy of a halloysite from Hunan Xianrenwan, China. This halloysite contains around 8% of quartz (SiO2) and nearly 9% gibbsite (Al(OH)3). In their interpretation of the spectra these impurities were completely ignored. Careful comparison with a phase pure halloysite from Southern Belgium, synthetic gibbsite, gibbsite from Minas Gerais, and quartz show that these impurities do have a marked influence on the mid-infrared and infrared emission spectra. In the near-infrared, the effect is much less pronounced. Quartz does not show bands in this region and the gibbsite bands will be very weak. Comparison still show that the presence of gibbsite does contribute to the overall spectrum and bands that were ascribed to the halloysite alone do coincide with those of gibbsite. Copyright © 2014 Elsevier B.V. All rights reserved.

Mineralogical and geomicrobial examination of soil contamination by radioactive Cs due to 2011 Fukushima Daiichi Nuclear Power Plant accident

NASA Astrophysics Data System (ADS)

Akai, Junji; Nomura, Nao; Matsushita, Shin; Kudo, Hisaaki; Fukuhara, Haruo; Matsuoka, Shiro; Matsumoto, Jinko

Soil contamination by radioactive Cs from Fukushima Daiichi Nuclear Power Plant accident was investigated. Absorption and desorption experiments of Cs were conducted for several phyllosillicates (kaolinite, sericite, montmorillonite, vermiculite, chrysotile and biotite), zeolite and solid organic matter (dead and green leaves). The results confirmed the characteristic sorption and desorption of Cs by these materials. The 2:1 type phyllosilicate, especially, vermiculite and montmorillonite absorbed Cs well. Heated vermiculite for agricultural use and weathered montmorillonite also adsorbed Cs. Leaves also absorbed Cs considerably but easily desorbed it. In summary, the relative capacity and strength of different materials for sorption of Cs followed the order: zeolite (clinoptilolite) > 2:1 type clay mineral > 1:1 type clay mineral > dead and green leaves. Culture experiments using bacteria of both naturally living on dead leaves in Iitate village, Fukushima Pref. and bacterial strains of Bacillus subtillis, Rhodococus erythropolis, Streptomyces aomiensis and Actinomycetospora chlora were carried out. Non-radioactive 1% Cs solution (CsCl) was added to the culture media. Two types of strong or considerable bacterial uptakes of Cs were found in bacterial cells. One is that Cs was contained mainly as globules inside bacteria and the other is that Cs was absorbed in the whole bacterial cells. The globules consisted mainly of Cs and P. Based on all these results, future diffusion and re-circulation behavior of Cs in the surface environment was discussed.

A Type System For Certified Runtime Type Analysis

DTIC Science & Technology

2002-12-01

1999 ACM SIGPLAN International Conf. on Functional Pro- gramming (ICFP’99), pages 183–196. ACM Press, September 1999. [Min97] Yasuhiko Minamide. Full...lifting of type parameters. Technical report, RIMS, Kyoto University, 1997. [MMH96] Yasuhiko Minamide, Greg Morrisett, and Robert Harper. Typed

Quantifying the in-channel retention of cohesive sediments during artificial flood events using FTIR-DRIFT spectrometry

NASA Astrophysics Data System (ADS)

Kurtenbach, A.; Gallé, T.; Buis, K.; de Sutter, R.; Troch, P.; Eisold, B.; Bierl, R.; Symader, W.

2010-05-01

Cohesive sediments control river ecosystem quality both as a transport medium for contaminants and as clogging material of stream bottom habitats. However, experimental field studies with fine-grained sediments in fluvial systems are rather scarce owing to the lack of adequate tracers and detection methods. As a result, current modelling approaches only insufficiently describe hydrodynamic transport and depositional behaviour of fine-grained sediments in rivers. We adopted two strategies to specifically study cohesive sediment dynamics in natural systems under defined boundary conditions. First, artificial floods were generated in the Olewiger Bach basin (24 km²), a mid-mountain gravel bed river, in order to characterise the in-channel fine sediment dynamics on their own. The advantage of these artificial flood waves lies in the selective control on some governing processes by experimental design. Second, fine sediment transport and deposition during these controlled reservoir releases were analysed by introducing the clay mineral kaolinite as a fine particle tracer, whose concentration was measured by Fourier transform infrared spectroscopy (FTIR) in diffuse reflectance mode (DRIFT). The DRIFT technique offers some important advantages such as the ability to assess both mineral and organic structures in aquatic particles, good sensitivity and high throughput (Gallé et al. 2004). Our laboratory tests confirm that FTIR-DRIFT spectrometry is capable of detecting the kaolinite tracer even in low percentage solid concentrations. The mass balance of the injected kaolinite for near bank-full artificial floods showed that, in spite of the very fine material and the non-stationary boundary conditions, over 50 percent of the tracer could be retained over a flow length of only 500 m. By combining fine particulate and natural dissolved tracers (e.g. dissolved organic carbon, DOC) we were able to identify the hyporheic zone as a potential short-term retention and storage

Clay mineralogy in different geomorphic surfaces in sugarcane areas

NASA Astrophysics Data System (ADS)

Camargo, L.; Marques, J., Jr.

2012-04-01

The crystallization of the oxides and hydroxides of iron and aluminum and kaolinite of clay fraction is the result of pedogenetic processes controlled by the relief. These minerals have influence on the physical and chemical attributes of soil and exhibit spatial dependence. The pattern of spatial distribution is influenced by forms of relief as the geomorphic surfaces. In this sense, the studies aimed at understanding the relationship between relief and the distribution pattern of the clay fraction attributes contribute to the delineation of specific areas of management in the field. The objective of this study was to evaluate the spatial distribution of oxides and hydroxides of iron and aluminum and kaolinite of clay fraction and its relationship with the physical and chemical attributes in different geomorphic surfaces. Soil samples were collected in a transect each 25 m (100 samples) and in the sides of the same (200 samples) as well as an area of 500 ha (1 sample each six hectare). Geomorphic surfaces (GS) in the transect were mapped in detail to support mapping the entire area. The soil samples were taken to the laboratory for chemical, physical, and mineralogical analysis, and the pattern of spatial distribution of soil attributes was obtained by statistics and geostatistics. The GS I is considered the oldest surface of the study area, with depositional character, and a slope ranging from 0 to 4%. GS II and III are considered to be eroded, and the surface II plan a gentle slope that extends from the edge of the surface until the beginning of I and III. The crystallographic characteristics of the oxides and hydroxides of iron and aluminum and kaolinite showed spatial dependence and the distribution pattern corresponding to the limits present of the GS in the field. Surfaces I and II showed the best environments to the degree of crystallinity of hematite and the surface III to the greatest degree of crystallinity of goethite agreeing to the pedoenvironment

Identification of type II and type III pyoverdine receptors from Pseudomonas aeruginosa.

PubMed

de Chial, Magaly; Ghysels, Bart; Beatson, Scott A; Geoffroy, Valérie; Meyer, Jean Marie; Pattery, Theresa; Baysse, Christine; Chablain, Patrice; Parsons, Yasmin N; Winstanley, Craig; Cordwell, Stuart J; Cornelis, Pierre

2003-04-01

Pseudomonas aeruginosa produces, under conditions of iron limitation, a high-affinity siderophore, pyoverdine (PVD), which is recognized at the level of the outer membrane by a specific TonB-dependent receptor, FpvA. So far, for P. aeruginosa, three different PVDs, differing in their peptide chain, have been described (types I-III), but only the FpvA receptor for type I is known. Two PVD-producing P. aeruginosa strains, one type II and one type III, were mutagenized by a mini-TnphoA3 transposon. In each case, one mutant unable to grow in the presence of the strong iron chelator ethylenediaminedihydroxyphenylacetic acid (EDDHA) and the cognate PVD was selected. The first mutant, which had an insertion in the pvdE gene, upstream of fpvA, was unable to take up type II PVD and showed resistance to pyocin S3, which is known to use type II FpvA as receptor. The second mutant was unable to take up type III PVD and had the transposon insertion in fpvA. Cosmid libraries of the respective type II and type III PVD wild-type strains were constructed and screened for clones restoring the capacity to grow in the presence of PVD. From the respective complementing genomic fragments, type II and type III fpvA sequences were determined. When in trans, type II and type III fpvA restored PVD production, uptake, growth in the presence of EDDHA and, in the case of type II fpvA, pyocin S3 sensitivity. Complementation of fpvA mutants obtained by allelic exchange was achieved by the presence of cognate fpvA in trans. All three receptors posses an N-terminal extension of about 70 amino acids, similar to FecA of Escherichia coli, but only FpvAI has a TAT export sequence at its N-terminal end.

Types of Diabetes

MedlinePlus

... Type 1 Diabetes Type 2 Diabetes Insulin Resistance & Prediabetes Gestational Diabetes Monogenic Diabetes Symptoms & Causes Risk Factors ... to develop type 2 diabetes if you have prediabetes or had gestational diabetes when you were pregnant. ...

Chemical-free n-type and p-type multilayer-graphene transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dissanayake, D. M. N. M., E-mail: nandithad@voxtel-inc.com; Eisaman, M. D.; Department of Electrical and Computer Engineering, Stony Brook University, Stony Brook, New York 11794

A single-step doping method to fabricate n- and p-type multilayer graphene (MG) top-gate field effect transistors (GFETs) is demonstrated. The transistors are fabricated on soda-lime glass substrates, with the n-type doping of MG caused by the sodium in the substrate without the addition of external chemicals. Placing a hydrogen silsesquioxane (HSQ) barrier layer between the MG and the substrate blocks the n-doping, resulting in p-type doping of the MG above regions patterned with HSQ. The HSQ is deposited in a single fabrication step using electron beam lithography, allowing the patterning of arbitrary sub-micron spatial patterns of n- and p-type doping.more » When a MG channel is deposited partially on the barrier and partially on the glass substrate, a p-type and n-type doping profile is created, which is used for fabricating complementary transistors pairs. Unlike chemically doped GFETs in which the external dopants are typically introduced from the top, these substrate doped GFETs allow for a top gate which gives a stronger electrostatic coupling to the channel, reducing the operating gate bias. Overall, this method enables scalable fabrication of n- and p-type complementary top-gated GFETs with high spatial resolution for graphene microelectronic applications.« less

Analysis of type II and type III solar radio bursts

NASA Astrophysics Data System (ADS)

Wijesekera, J. V.; Jayaratne, K. P. S. C.; Adassuriya, J.

2018-04-01

Solar radio burst is an arrangement of a frequency space that variation with time. Most of radio burst can be identified in low frequency range such as below 200 MHz and depending on frequencies. Solar radio bursts were the first phenomenon identified in the field of radio astronomy field. Solar radio frequency range is from 70 MHz to 2.2 GHz. Most of the radio burst can be identified in a low frequency range such as below 200 MHz. Properties of low-frequency radio were analyzed this research. There are two types of solar radio bursts were analyzed, named as type II and type III radio bursts. Exponential decay type could be seen in type II, and a linear could be indicated in type III solar radio bursts. The results of the drift rate graphs show the values of each chosen solar radio burst. High drift rate values can be seen in type III solar flares whereas low to medium drift rate values can be seen in type II solar flares. In the second part of the research the Newkirk model electron density model was used to estimate the drift velocities of the solar radio bursts. Although the special origin of the solar radio burst is not known clearly we assumed. The chosen solar radio bursts were originated within the solar radius of 0.9 - 1.3 range from the photosphere. We used power low in the form of (x) = A × 10‑bx were that the electron density related to the height of the solar atmosphere. The calculation of the plasma velocity of each solar radio burst was done using the electron density model and drift rates. Therefore velocity of chosen type II solar radio bursts indicates low velocities. The values are 233.2499 Km s‑1, 815.9522 Km s‑1 and 369.5425 Km s‑1. Velocity of chosen type III solar radio bursts were 1443.058 Km s‑1and 1205.05Km s ‑1.

Abiotic protein fragmentation by manganese oxide: Implications for a mechanism to supply soil biota with oligopeptides

DOE PAGES

Reardon, Patrick N.; Chacon, Stephany S.; Walter, Eric D.; ...

2016-03-14

Proteins facilitate a wide range of chemical transformations important in soil as well as being a major reservoir of soil nitrogen themselves. The interactions and reactions of proteins with soils and minerals are of key importance to our understanding of their functional persistence in the environment. We combined NMR and EPR spectroscopies to distinguish the reaction of a model protein with a redox active mineral surface (Birnessite, MnO 2) from its response to a redox neutral phyllosilicate (Kaolinite). Our data demonstrate that birnessite fragments the model protein while kaolinite has little impact on the protein structure. NMR and EPR spectroscopiesmore » are shown to be valuable tools to observe these reactions and capture the extent of protein transformation together with the extent of mineral response. These data suggest that mineral surfaces can have both promoting and retarding roles in terrestrial nitrogen cycling, with redox active minerals acting as accelerators by catalyzing the breakdown of proteins and proteinaceous materials while phyllosilicates are more likely to act as preservative media.« less

Protein–Mineral Interactions: Molecular Dynamics Simulations Capture Importance of Variations in Mineral Surface Composition and Structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Amity; Reardon, Patrick N.; Chacon, Stephany S.

Molecular dynamics simulations, conventional and metadynamics, were performed to determine the interaction of model protein Gb1 over kaolinite (001), Na+-montmorillonite (001), Ca2+-montmorillonite (001), goethite (100), and Na+-birnessite (001) mineral surfaces. Gb1, a small (56 residue) protein with a well-characterized solution-state nuclear magnetic resonance (NMR) structure and having α-helix, four-fold β-sheet, and hydrophobic core features, is used as a model protein to study protein soil mineral interactions and gain insights on structural changes and potential degradation of protein. From our simulations, we observe little change to the hydrated Gb1 structure over the kaolinite, montmorillonite, and goethite surfaces relative to its solvatedmore » structure without these mineral surfaces present. Over the Na+-birnessite basal surface, however, the Gb1 structure is highly disturbed as a result of interaction with this birnessite surface. Unraveling of the Gb1 β-sheet at specific turns and a partial unraveling of the α-helix is observed over birnessite, which suggests specific vulnerable residue sites for oxidation or hydrolysis possibly leading to fragmentation.« less

Abiotic Protein Fragmentation by Manganese Oxide: Implications for a Mechanism to Supply Soil Biota with Oligopeptides.

PubMed

Reardon, Patrick N; Chacon, Stephany S; Walter, Eric D; Bowden, Mark E; Washton, Nancy M; Kleber, Markus

2016-04-05

The ability of plants and microorganisms to take up organic nitrogen in the form of free amino acids and oligopeptides has received increasing attention over the last two decades, yet the mechanisms for the formation of such compounds in soil environments remain poorly understood. We used Nuclear Magnetic Resonance (NMR) and Electron Paramagnetic Resonance (EPR) spectroscopies to distinguish the reaction of a model protein with a pedogenic oxide (Birnessite, MnO2) from its response to a phyllosilicate (Kaolinite). Our data demonstrate that birnessite fragments the model protein while kaolinite does not, resulting in soluble peptides that would be available to soil biota and confirming the existence of an abiotic pathway for the formation of organic nitrogen compounds for direct uptake by plants and microorganisms. The absence of reduced Mn(II) in the solution suggests that birnessite acts as a catalyst rather than an oxidant in this reaction. NMR and EPR spectroscopies are shown to be valuable tools to observe these reactions and capture the extent of protein transformation together with the extent of mineral response.

Emerging integrated nanoclay-facilitated drug delivery system for papillary thyroid cancer therapy

NASA Astrophysics Data System (ADS)

Zhang, Yi; Long, Mei; Huang, Peng; Yang, Huaming; Chang, Shi; Hu, Yuehua; Tang, Aidong; Mao, Linfeng

2016-09-01

Nanoclay can be incorporated into emerging dual functional drug delivery systems (DDSs) to promote efficiency in drug delivery and reduce the toxicity of doxorubicin (DOX) used for thyroid cancer treatment. This paper reports the expansion of the basal spacing of kaolinite nanoclay was expanded from 0.72 nm to 0.85 nm, which could provide sufficiently spacious site for hosting doxorubicin molecules and controlling the diffusion rate. A targeted design for papillary thyroid cancer cells was achieved by introducing KI, which is consumed by the sodium-iodide symporter (NIS). As indicated by MTT assays, confocal laser scanning microscopy and bio-TEM observations, methoxy-intercalated kaolinite (KaolinMeOH) exhibited negligible cytotoxicity against papillary thyroid cancer cells. By contrast, DOX-KaolinMeOH showed dose-dependent therapeutic effects in vitro, and KI@DOX-KaolinMeOH was found to act as a powerful targeted therapeutic drug. Furthermore, active and passive targeting strategies played a role in the accumulation of the drug molecules, as verified by an in vivo bio-distribution analysis.

Illite equilibria in solutions: III. A re-interpretation of the data of Sass et al. (1987)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aja, S.U.

1991-11-01

In a recent solubility study of Goose Lake and Beavers Bend illite, SASS et al. (1987) inferred the existence of three components of natural illites (K{sub 0.24}/O{sub 10}(OH){sub 2}), (K{sub 0.67}/O{sub 10}(OH){sub 2}), and (K{sub 0.90}/O{sub 10}(OH){sub 2}) which were interpreted to be smectite, illite, and K-mica, respectively. They also speculated that illite-smectite equilibrium is metastable under diagenetic conditions except between 90 and 110C where it is stabilized by an ordering transition. A re-interpretation of the data of SASS et al. (1987) indicates that the solubility-controlling phases have the following K atoms per half cell: 0.29, 0.52, 0.69, 0.084, andmore » 1.0. Furthermore, solution equilibration investigations of kaolinite-microcline mixtures have shown that these two minerals do not coexist stably. Thus, the question of an ordering transition whose main effect is to stabilize illite-smectite equilibria relative to kaolinite-microcline assemblage does not arise.« less

Biodegradation of crude oil saturated fraction supported on clays.

PubMed

Ugochukwu, Uzochukwu C; Jones, Martin D; Head, Ian M; Manning, David A C; Fialips, Claire I

2014-02-01

The role of clay minerals in crude oil saturated hydrocarbon removal during biodegradation was investigated in aqueous clay/saturated hydrocarbon microcosm experiments with a hydrocarbon degrading microorganism community. The clay minerals used for this study were montmorillonite, palygorskite, saponite and kaolinite. The clay mineral samples were treated with hydrochloric acid and didecyldimethylammonium bromide to produce acid activated- and organoclays respectively which were used in this study. The production of organoclay was restricted to only montmorillonite and saponite because of their relative high CEC. The study indicated that acid activated clays, organoclays and unmodified kaolinite, were inhibitory to biodegradation of the hydrocarbon saturates. Unmodified saponite was neutral to biodegradation of the hydrocarbon saturates. However, unmodified palygorskite and montmorillonite were stimulatory to biodegradation of the hydrocarbon saturated fraction and appears to do so as a result of the clays' ability to provide high surface area for the accumulation of microbes and nutrients such that the nutrients were within the 'vicinity' of the microbes. Adsorption of the saturated hydrocarbons was not significant during biodegradation.

Role of DDL processes during electrolytic reduction of Cu(II) in a low oxygen environment.

PubMed

Brosky, Rebekah T; Pamukcu, Sibel

2013-11-15

Heavy metals typically accumulate in reduced bottom sediments after being discharged into waterways by industrial and municipal processes. A laboratory experiment was conducted in order to determine if abundance of clay in the bottom sediments of a Cu-contaminated aqueous ecosystem could enhance electrolytic reduction of the heavy metal. Cu(NO3)2 · 2.5H2O was added to simulate a moderately contaminated system with 650 μg Cu/ml kaolinite clay-water slurry. A constant electrical potential of 1.0 V/cm was applied across platinum wire electrodes inserted into the continuously stirred system for four days while the system ORP(2) was monitored and periodic sub-samples were taken for analysis. The electrical as well as the chemical results indicate that the quantity of Cu(II) being reduced to Cu(I), especially within the aqueous phase, is increased within the first 48 h of experimentation by the presence of kaolinite clay up to 0.05 mg clay/l slurry. Copyright © 2013 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reardon, Patrick N.; Chacon, Stephany S.; Walter, Eric D.

Proteins facilitate a wide range of chemical transformations important in soil as well as being a major reservoir of soil nitrogen themselves. The interactions and reactions of proteins with soils and minerals are of key importance to our understanding of their functional persistence in the environment. We combined NMR and EPR spectroscopies to distinguish the reaction of a model protein with a redox active mineral surface (Birnessite, MnO 2) from its response to a redox neutral phyllosilicate (Kaolinite). Our data demonstrate that birnessite fragments the model protein while kaolinite has little impact on the protein structure. NMR and EPR spectroscopiesmore » are shown to be valuable tools to observe these reactions and capture the extent of protein transformation together with the extent of mineral response. These data suggest that mineral surfaces can have both promoting and retarding roles in terrestrial nitrogen cycling, with redox active minerals acting as accelerators by catalyzing the breakdown of proteins and proteinaceous materials while phyllosilicates are more likely to act as preservative media.« less

Oxidative and photoxidative polymerization of humic suprastructures by heterogeneous biomimetic catalysis.

PubMed

Nuzzo, Assunta; Piccolo, Alessandro

2013-05-13

The meso-tetra(2,6-dichloro-3-sulfonatophenyl)porphyrinate of manganese(III) chloride [Mn-(TDCPPS)Cl] biomimetic catalyst immobilized on spacer-functionalized kaolinite clay mineral was employed in the oxidative coupling reaction of a dissolved humic acid (HA) suprastructure with either chemical (H2O2) or UV-light oxidation. The changes in molecular size of humic matter subjected to catalyzed oxidative reaction were followed by high-performance size exclusion chromatography (HPSEC) with UV-vis and refractive index (RI) detectors in series, and by thermogravimetric (TGA) analysis. Both the enhanced molecular size shown by differences between HPSEC chromatograms of humic reaction mixtures at either pH 6 or 3.5 and the increase of thermogravimetric stability suggest that the heterogeneous biomimetic catalysis promoted the stabilization of humic conformations by new intermolecular covalent bonds during oxidative coupling. The similarity between chemical and light-induced oxidation results suggests potential multiple applications of the kaolinite-supported heterogeneous catalyst in controlling the reactivity of natural organic matter within biogeochemical cycles and environmental reactions.

Types of chemotherapy

MedlinePlus

... or on cancer cells. How Doctors Choose Your Chemotherapy The type and dose of chemotherapy your doctor gives you ... drugs. Below are the seven main types of chemotherapy, the types of cancer they treat, and examples. The caution ...

Characterisation of inorganic microparticles in pigment cells of human gut associated lymphoid tissue.

PubMed Central

Powell, J J; Ainley, C C; Harvey, R S; Mason, I M; Kendall, M D; Sankey, E A; Dhillon, A P; Thompson, R P

1996-01-01

Macrophages at the base of human gut associated lymphoid tissue (GALT), become loaded early in life with dark granular pigment that is rich in aluminium, silicon, and titanium. The molecular characteristics, intracellular distribution, and source of this pigment is described. Laser scanning and electron microscopy showed that pigmented macrophages were often closely related to collagen fibres and plasma cells in GALT of both small and large intestine and contained numerous phagolysosomes, previously described as granules, that are rich in electron dense submicron sized particles. Morphological assessment, x ray microanalysis, and image electron energy loss spectroscopy showed three distinct types of microparticle: type I - spheres of titanium dioxide, 100-200 nm diameter, characterised as the synthetic food-additive polymorph anatase; type II - aluminosilicates, < 100-400 nm in length, generally of flaky appearance, often with adsorbed surface iron, and mostly characteristic of the natural clay mineral kaolinite; and type III - mixed environmental silicates without aluminium, 100-700 nm in length and of variable morphology. Thus, this cellular pigment that is partly derived from food additives and partly from the environment is composed of inert inorganic microparticles and loaded into phagolysosomes of macrophages within the GALT of all human subjects. These observations suggest that the pathogenicity of this pigment should be further investigated since, in susceptible individuals, the same intracellular distribution of these three types of submicron particle causes chronic latent granulomatous inflammation. Images Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 7 PMID:8675092

Diabetes Type 2

MedlinePlus

Diabetes means your blood glucose, or blood sugar, levels are too high. With type 2 diabetes, the more common type, your body does not ... You have a higher risk of type 2 diabetes if you are older, have obesity, have a ...

Experimental observation of standing interfacial waves induced by surface waves in muddy water

NASA Astrophysics Data System (ADS)

Maxeiner, Eric; Dalrymple, Robert A.

2011-09-01

A striking feature has been observed in a laboratory wave tank with a thin layer of clear water overlying a layer of mud. A piston-type wave maker is used to generate long monochromatic surface waves in a tank with a layer of kaolinite clay at the bottom. The wave action on the mud causes the clay particles to rise from the bottom into the water column, forming a lutocline. As the lutocline approaches the water surface, a set of standing interfacial waves form on the lutocline. The interfacial wave directions are oriented nearly orthogonal to the surface wave direction. The interfacial waves, which sometimes cover the entire length and width of the tank, are also temporally subharmonic as the phase of the interfacial wave alternates with each passing surface wave crest. These interfacial waves are the result of a resonant three-wave interaction involving the surface wave train and the two interfacial wave trains. The interfacial waves are only present when the lutocline is about 3 cm of the water surface and they can be sufficiently nonlinear as to exhibit superharmonics and a breaking-type of instability.

Cantilever-type Thermal Microactuators Fabricated by SOI-MUMPs with U-type and I-type Configurations

NASA Astrophysics Data System (ADS)

Osada, Takahiro; Ochiai, Kuniyuki; Osada, Kazuki; Muro, Hideo

Recently, the micro fluid systems have been extensively studied, where microactuators such as micro valves fabricated by MEMS technology are essential for realizing these systems. In this paper thermal microactuators with U-type and I-type shapes fabricated by SOI-MUMPs technology have been investigated for optimizing their configurations.

Theory of Type 3 and Type 2 Solar Radio Emissions

NASA Technical Reports Server (NTRS)

Robinson, P. A.; Cairns, I. H.

2000-01-01

The main features of some current theories of type III and type II bursts are outlined. Among the most common solar radio bursts, type III bursts are produced at frequencies of 10 kHz to a few GHz when electron beams are ejected from solar active regions, entering the corona and solar wind at typical speeds of 0.1c. These beams provide energy to generate Langmuir waves via a streaming instability. In the current stochastic-growth theory, Langmuir waves grow in clumps associated with random low-frequency density fluctuations, leading to the observed spiky waves. Nonlinear wave-wave interactions then lead to secondary emission of observable radio waves near the fundamental and harmonic of the plasma frequency. Subsequent scattering processes modify the dynamic radio spectra, while back-reaction of Langmuir waves on the beam causes it to fluctuate about a state of marginal stability. Theories based on these ideas can account for the observed properties of type III bursts, including the in situ waves and the dynamic spectra of the radiation. Type 11 bursts are associated with shock waves propagating through the corona and interplanetary space and radiating from roughly 30 kHz to 1 GHz. Their basic emission mechanisms are believed to be similar to those of type III events and radiation from Earth's foreshock. However, several sub-classes of type II bursts may exist with different source regions and detailed characteristics. Theoretical models for type II bursts are briefly reviewed, focusing on a model with emission from a foreshock region upstream of the shock for which observational evidence has just been reported.

INSECTICIDAL TOXIN FROM BACILLUS THURINGIENSIS IS RELEASED FROM ROOTS OF TRANSGENIC BT CORN IN VITRO AND IN SITU. (R826107)

EPA Science Inventory

Abstract

The insecticidal toxin encoded by the cry1Ab gene from Bacillus thuringiensis was released in root exudates from transgenic Bt corn during 40 days of growth in soil amended to 0, 3, 6, 9, or 12% (v/v) with montmorillonite or kaolinite in a...

Strategy for Extracting DNA from Clay Soil and Detecting a Specific Target Sequence via Selective Enrichment and Real-Time (Quantitative) PCR Amplification ▿

PubMed Central

Yankson, Kweku K.; Steck, Todd R.

2009-01-01

We present a simple strategy for isolating and accurately enumerating target DNA from high-clay-content soils: desorption with buffers, an optional magnetic capture hybridization step, and quantitation via real-time PCR. With the developed technique, μg quantities of DNA were extracted from mg samples of pure kaolinite and a field clay soil. PMID:19633108

Charting improvements in US registry HLA typing ambiguity using a typing resolution score.

PubMed

Paunić, Vanja; Gragert, Loren; Schneider, Joel; Müller, Carlheinz; Maiers, Martin

2016-07-01

Unrelated stem cell registries have been collecting HLA typing of volunteer bone marrow donors for over 25years. Donor selection for hematopoietic stem cell transplantation is based primarily on matching the alleles of donors and patients at five polymorphic HLA loci. As HLA typing technologies have continually advanced since the beginnings of stem cell transplantation, registries have accrued typings of varied HLA typing ambiguity. We present a new typing resolution score (TRS), based on the likelihood of self-match, that allows the systematic comparison of HLA typings across different methods, data sets and populations. We apply the TRS to chart improvement in HLA typing within the Be The Match Registry of the United States from the initiation of DNA-based HLA typing to the current state of high-resolution typing using next-generation sequencing technologies. In addition, we present a publicly available online tool for evaluation of any given HLA typing. This TRS objectively evaluates HLA typing methods and can help define standards for acceptable recruitment HLA typing. Copyright © 2016 American Society for Histocompatibility and Immunogenetics. Published by Elsevier Inc. All rights reserved.

Development of type-I/type-II hybrid dye sensitizer with both pyridyl group and catechol unit as anchoring group for type-I/type-II dye-sensitized solar cell.

PubMed

Ooyama, Yousuke; Furue, Kensuke; Enoki, Toshiaki; Kanda, Masahiro; Adachi, Yohei; Ohshita, Joji

2016-11-09

A type-I/type-II hybrid dye sensitizer with a pyridyl group and a catechol unit as the anchoring group has been developed and its photovoltaic performance in dye-sensitized solar cells (DSSCs) is investigated. The sensitizer has the ability to adsorb on a TiO 2 electrode through both the coordination bond at Lewis acid sites and the bidentate binuclear bridging linkage at Brønsted acid sites on the TiO 2 surface, which makes it possible to inject an electron into the conduction band of the TiO 2 electrode by the intramolecular charge-transfer (ICT) excitation (type-I pathway) and by the photoexcitation of the dye-to-TiO 2 charge transfer (DTCT) band (type-II pathway). It was found that the type-I/type-II hybrid dye sensitizer adsorbed on TiO 2 film exhibits a broad photoabsorption band originating from ICT and DTCT characteristics. Here we reveal the photophysical and electrochemical properties of the type-I/type-II hybrid dye sensitizer bearing a pyridyl group and a catechol unit, along with its adsorption modes onto TiO 2 film, and its photovoltaic performance in type-I/type-II DSSC, based on optical (photoabsorption and fluorescence spectroscopy) and electrochemical measurements (cyclic voltammetry), density functional theory (DFT) calculation, FT-IR spectroscopy of the dyes adsorbed on TiO 2 film, photocurrent-voltage (I-V) curves, incident photon-to-current conversion efficiency (IPCE) spectra, and electrochemical impedance spectroscopy (EIS) for DSSC.

Headache and Decompression Sickness: Type I or Type II?

DTIC Science & Technology

2001-06-01

criteria for Type I instead of Type II DCS. This includes no clear alternative diagnosis, a localized headache along the suture, and no nerologic findings...page survey. Here, demographic information, exposure data, predisposing factors, symptom onset, symptoms and signs, diagnosis, disease progression

Retinal tissue thickness in type 1 and type 2 diabetes.

PubMed

Srinivasan, Sangeetha; Pritchard, Nicola; Sampson, Geoff P; Edwards, Katie; Vagenas, Dimitrios; Russell, Anthony W; Malik, Rayaz A; Efron, Nathan

2016-01-01

The objective was to investigate full retinal and inner retinal thickness in individuals with type 1 and type 2 diabetes. Eighty-four individuals with type 1 diabetes (T1DM), 67 individuals with type 2 diabetes (T2DM) and 42 non-diabetic individuals (control group) were enrolled. Participants underwent full retinal thickness evaluation in the central retinal, parafoveal and perifoveal zones and in the retinal nerve fibre layer (RNFL) and ganglion cell complex (GCC), using spectral domain optical coherence tomography. As a preliminary step, the key variables of interest - age, sex, diabetic retinopathy (DR), duration of diabetes and HbA1c levels - were analysed and compared between the three groups. Full retinal thickness, RNFL and GCC thicknesses were also compared between the groups. The relationship between the type of diabetes and retinal tissue thickness was explored, adjusting for the five potential confounders. Compared to individuals with T1DM, individuals with T2DM had significantly reduced full retinal thickness in the parafovea and perifovea and reduced RNFL and GCC thickness. The mean differences were six (p = 0.020), seven (p = 0.008), six (p = 0.021) and four micrometres (p = 0.013) for the parafovea, perifovea, RNFL and GCC thicknesses, respectively. Thicknesses within the central zone (p = 0.018) and at the parafovea (p = 0.007) were significantly reduced in T2DM when compared to the control group. After adjusting for age, sex, diabetic retinopathy, duration of diabetes and HbA1c levels, the relationship between type of diabetes and retinal tissue thickness was not statistically significant (p > 0.056). Retinal tissue thickness is not significantly different between type 1 and type 2 diabetes, when adjusted for age, sex, diabetic retinopathy, duration of diabetes and HbA1c levels. © 2016 Optometry Australia.

Advances in Blood Typing.

PubMed

Quraishy, N; Sapatnekar, S

The clinical importance of blood group antigens relates to their ability to evoke immune antibodies that are capable of causing hemolysis. The most important antigens for safe transfusion are ABO and D (Rh), and typing for these antigens is routinely performed for patients awaiting transfusion, prenatal patients, and blood donors. Typing for other blood group antigens, typically of the Kell, Duffy, Kidd, and MNS blood groups, is sometimes necessary, for patients who have, or are likely to develop antibodies to these antigens. The most commonly used typing method is serological typing, based on hemagglutination reactions against specific antisera. This method is generally reliable and practical for routine use, but it has certain drawbacks. In recent years, molecular typing has emerged as an alternative or supplemental typing method. It is based on detecting the polymorphisms and mutations that control the expression of blood group antigens, and using this information to predict the probable antigen type. Molecular typing methods are useful when traditional serological typing methods cannot be used, as when a patient has been transfused and the sample is contaminated with red blood cells from the transfused blood component. Moreover, molecular typing methods can precisely identify clinically significant variant antigens that cannot be distinguished by serological typing; this capability has been exploited for the resolution of typing discrepancies and shows promise for the improved transfusion management of patients with sickle cell anemia. Despite its advantages, molecular typing has certain limitations, and it should be used in conjunction with serological methods. © 2016 Elsevier Inc. All rights reserved.

Wild type measles virus attenuation independent of type I IFN.

PubMed

Druelle, Johan; Sellin, Caroline I; Waku-Kouomou, Diane; Horvat, Branka; Wild, Fabian T

2008-02-03

Measles virus attenuation has been historically performed by adaptation to cell culture. The current dogma is that attenuated virus strains induce more type I IFN and are more resistant to IFN-induced protection than wild type (wt). The adaptation of a measles virus isolate (G954-PBL) by 13 passages in Vero cells induced a strong attenuation of this strain in vivo. The adapted virus (G954-V13) differs from its parental strain by only 5 amino acids (4 in P/V/C and 1 in the M gene). While a vaccine strain, Edmonston Zagreb, could replicate equally well in various primate cells, both G954 strains exhibited restriction to the specific cell type used initially for their propagation. Surprisingly, we observed that both G954 strains induced type I IFN, the wt strain inducing even more than the attenuated ones, particularly in human plasmacytoid Dendritic Cells. Type I IFN-induced protection from the infection of both G954 strains depended on the cell type analyzed, being less efficient in the cells used to grow the viral strain. Thus, mutations in M and P/V/C proteins can critically affect MV pathogenicity, cellular tropism and lead to virus attenuation without interfering with the alpha/beta IFN system.

Wild type measles virus attenuation independent of type I IFN

PubMed Central

Druelle, Johan; Sellin, Caroline I; Waku-Kouomou, Diane; Horvat, Branka; Wild, Fabian T

2008-01-01

Background Measles virus attenuation has been historically performed by adaptation to cell culture. The current dogma is that attenuated virus strains induce more type I IFN and are more resistant to IFN-induced protection than wild type (wt). Results The adaptation of a measles virus isolate (G954-PBL) by 13 passages in Vero cells induced a strong attenuation of this strain in vivo. The adapted virus (G954-V13) differs from its parental strain by only 5 amino acids (4 in P/V/C and 1 in the M gene). While a vaccine strain, Edmonston Zagreb, could replicate equally well in various primate cells, both G954 strains exhibited restriction to the specific cell type used initially for their propagation. Surprisingly, we observed that both G954 strains induced type I IFN, the wt strain inducing even more than the attenuated ones, particularly in human plasmacytoid Dendritic Cells. Type I IFN-induced protection from the infection of both G954 strains depended on the cell type analyzed, being less efficient in the cells used to grow the viral strain. Conclusion Thus, mutations in M and P/V/C proteins can critically affect MV pathogenicity, cellular tropism and lead to virus attenuation without interfering with the α/β IFN system. PMID:18241351

Heavy metals alter the electrokinetic properties of bacteria, yeasts, and clay minerals.

PubMed Central

Collins, Y E; Stotzky, G

1992-01-01

The electrokinetic patterns of four bacterial species (Bacillus subtilis, Bacillus megaterium, Pseudomonas aeruginosa, and Agrobacterium radiobacter), two yeasts (Saccharomyces cerevisiae and Candida albicans), and two clay minerals (montmorillonite and kaolinite) in the presence of the chloride salts of the heavy metals, Cd, Cr, Cu, Hg, Ni, Pb, and Zn, and of Na and Mg were determined by microelectrophoresis. The cells and kaolinite were net negatively charged at pH values above their isoelectric points (pI) in the presence of Na, Mg, Hg, and Pb at an ionic strength (mu) of 3 x 10(-4); montmorillonite has no pI and was net negatively charged at all pH values in the presence of these metals. However, the charge of some bacteria, S. cerevisiae, and kaolinite changed to a net positive charge (charge reversal) in the presence of Cd, Cr, Cu, Ni, and Zn at pH values above 5.0 (the pH at which charge reversal occurred differed with the metal) and then, at higher pH values, again became negative. The charge of the bacteria and S. cerevisiae also reversed in solutions of Cu and Ni with a mu of greater than 3 x 10(-4), whereas there was no reversal in solutions with a mu of less than 3 x 10(-4). The clays became net positively charged when the mu of Cu was greater than 3 x 10(-4) and that of Ni was greater than 1.5 x 10(-4). The charge of the cells and clays also reversed in solutions containing both Mg and Ni or both Cu and Ni (except montmorillonite) but not in solutions containing both Mg and Cu (except kaolinite) (mu = 3 x 10(-4)). The pIs of the cells in the presence of the heavy metals were at either higher or lower pH values than in the presence of Na and Mg. Exposure of the cells to the various metals at pH values from 2 to 9 for the short times (ca. 10 min) required to measure the electrophoretic mobility did not affect their viability. The specific adsorption on the cells and clays of the hydrolyzed species of some of the heavy metals that formed at higher p

Types of Blood Donations

MedlinePlus

... Testing Find a Blood Drive Home Types of Blood Donations Types of Blood Donations Giving the "right" type of blood donation - ... make an appointment 1-800-RED CROSS About Blood Types There are actually more than 8 different ...

High cell surface death receptor expression determines type I versus type II signaling.

PubMed

Meng, Xue Wei; Peterson, Kevin L; Dai, Haiming; Schneider, Paula; Lee, Sun-Hee; Zhang, Jin-San; Koenig, Alexander; Bronk, Steve; Billadeau, Daniel D; Gores, Gregory J; Kaufmann, Scott H

2011-10-14

Previous studies have suggested that there are two signaling pathways leading from ligation of the Fas receptor to induction of apoptosis. Type I signaling involves Fas ligand-induced recruitment of large amounts of FADD (FAS-associated death domain protein) and procaspase 8, leading to direct activation of caspase 3, whereas type II signaling involves Bid-mediated mitochondrial perturbation to amplify a more modest death receptor-initiated signal. The biochemical basis for this dichotomy has previously been unclear. Here we show that type I cells have a longer half-life for Fas message and express higher amounts of cell surface Fas, explaining the increased recruitment of FADD and subsequent signaling. Moreover, we demonstrate that cells with type II Fas signaling (Jurkat or HCT-15) can signal through a type I pathway upon forced receptor overexpression and that shRNA-mediated Fas down-regulation converts cells with type I signaling (A498) to type II signaling. Importantly, the same cells can exhibit type I signaling for Fas and type II signaling for TRAIL (TNF-α-related apoptosis-inducing ligand), indicating that the choice of signaling pathway is related to the specific receptor, not some other cellular feature. Additional experiments revealed that up-regulation of cell surface death receptor 5 levels by treatment with 7-ethyl-10-hydroxy-camptothecin converted TRAIL signaling in HCT116 cells from type II to type I. Collectively, these results suggest that the type I/type II dichotomy reflects differences in cell surface death receptor expression.

Speciation of individual mineral particles of micrometer size by the combined use of attenuated total reflectance-Fourier transform-infrared imaging and quantitative energy-dispersive electron probe X-ray microanalysis techniques.

PubMed

Jung, Hae-Jin; Malek, Md Abdul; Ryu, JiYeon; Kim, BoWha; Song, Young-Chul; Kim, HyeKyeong; Ro, Chul-Un

2010-07-15

Our previous work demonstrated for the first time the potential of the combined use of two techniques, attenuated total reflectance FT-IR (ATR-FT-IR) imaging and a quantitative energy-dispersive electron probe X-ray microanalysis, low-Z particle EPMA, for the characterization of individual aerosol particles. In this work, the speciation of mineral particles was performed on a single particle level for 24 mineral samples, including kaolinite, montmorillonite, vermiculite, talc, quartz, feldspar, calcite, gypsum, and apatite, by the combined use of ATR-FT-IR imaging and low-Z particle EPMA techniques. These two single particle analytical techniques provide complementary information, the ATR-FT-IR imaging on mineral types and low-Z particle EPMA on the morphology and elemental concentrations, on the same individual particles. This work demonstrates that the combined use of the two single particle analytical techniques can powerfully characterize externally heterogeneous mineral particle samples in detail and has great potential for the characterization of airborne mineral dust particles.

Hydrothermal alteration of sediments associated with surface emissions from the Cerro Prieto geothermal field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Valette-Silver, J.N.; Esquer P., I.; Elders, W.A.

1981-01-01

A study of the mineralogical changes associated with these hydrothermal vents was initiated with the aim of developing possible exploration tools for geothermal resources. The Cerro Prieto reservoir has already been explored by extensive deep drilling so that relationships between surface manifestations and deeper hydrothermal processes could be established directly. Approximately 120 samples of surface sediments were collected both inside and outside of the vents. The mineralogy of the altered sediments studied appears to be controlled by the type of emission. A comparison between the changes in mineralogy due to low temperature hydrothermal activity in the reservoir, seen in samplesmore » from boreholes, and mineralogical changes in the surface emission samples shows similar general trends below 180 C: increase of quartz, feldspar and illite, with subsequent disappearance of kaolinite, montmorillonite, calcite and dolomite. These mineral assemblages seem to be characteristic products of the discharge from high intensity geothermal fields.« less

Graphical method for determining the coefficient of consolidation cv from a flow-pump permeability test

USGS Publications Warehouse

Morin, Roger H.; Olsen, Harold W.; Nelson, Karl R.; Gill, James D.

1989-01-01

A graphical method has been developed for determining the coefficient of consolidation from the transient phases of a flow-pump permeability test. The flow pump can be used to infuse fluid into or withdraw fluid from a laboratory sediment specimen at a constant volumetric rate in order to obtain data that can be used to calculate permeability using Darcy's law. Representative type-curve solutions to the associated forced-flow and pressure-decay models are derived. These curves provide the basis for graphically evaluating the permeability k, the coefficient of consolidation cv, and the coefficient of volume change mv. The curve-matching technique is easy and rapid. Values of k, cv and mv for a laterally confined kaolinite specimen were determined by this graphical method and appear to be in reasonably good agreement with numerically derived estimates (within 20%). Discrepancies between the two sets of results seem to be largely a function of data quality.

Comparison of the 1984 and 1985 AIS data over the Singatse Range (Yerington), Nevada

NASA Technical Reports Server (NTRS)

Lyon, R. J. P.

1986-01-01

The Singatse Range is composed of a series of 53 types of volcanic, plutonic, metamorphic, and sedimentary rocks. In addition the Jurassic plutonic rocks are also of economic interest for their copper mineralization which is contained in a porphyry dike swarm. The 1984 and 1985 flight results from the Airborne Imaging Spectrometer (AIS) instrument flown in the NASA/JPL C-130 aircraft are contrasted and compared. The 1984 data are less noisy than the 1985, in which many sets of vertical stripings from bad detectors can be seen. Significantly however, enough of the hydrothermal alteration patterns can be seen in each line at the mutual crossing points that one can say that the specific targets were detected in both year's flights. The spectra of both years are corrupted by the second-order effect from the grating, but 0-H bond absorption at essentially correct wavelengths for sericite and/or kaolinite can be seen.

Interspecies radioimmunoassay for the major structural proteins of primate type-D retroviruses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colcher, D.; Teramoto, Y.A.; Schlom, J.

1977-12-01

A competition radioimmunoassay has been developed in which type-D retroviruses from three primate species compete. The assay utilizes the major structural protein (36,000 daltons) of the endogenous squirrel monkey retrovirus and antisera directed against the major structural protein (27,000 daltons) of the Mason-Pfizer monkey virus isolated from rhesus monkeys. Purified preparations of both viruses grown in heterologous cells, as well as extracts of heterologous cells infected with squirrel monkey retrovirus or Mason-Pfizer monkey virus, compete completely in the assay. Addition of an endogenous virus of the langur monkey also results in complete blocking. No blocking in the assay is observedmore » with type-C baboon viruses, woolly monkey virus, and gibbon virus. Various other type-C and type-B viruses also showed no reactivity. An interspecies assay has thus been developed that recognizes the type-D retroviruses from both Old World monkey (rhesus and langur) and New World monkey (squirrel) species.« less

Cytogenetic and morphologic typing of 58 papillary renal cell carcinomas: evidence for a cytogenetic evolution of type 2 from type 1 tumors.

PubMed

Gunawan, Bastian; von Heydebreck, Anja; Fritsch, Thekla; Huber, Wolfgang; Ringert, Rolf-Hermann; Jakse, Gerhard; Füzesi, László

2003-10-01

We evaluated clinical characteristics, patient outcome (mean follow-up, 47 months), and cytogenetic abnormalities in the largest as yet reported cytogenetic series of 47 primary and 11 secondary papillary renal cell carcinomas for differences between the recently proposed type 1 and type 2 subtypes. Secondary tumors were more often of type 2 morphology (P = 0.02), whereas primary type 2 tumors were associated with higher clinical stage (P = 0.001) and worse patient outcome (P = 0.02). Although both subtypes had at least one of the primary chromosomal gains at 17q, 7, and 16q, type 2 tumors had moderately lower frequencies of primary gains at 17p (61 versus 94%; P = 0.007) and 17q (72 versus 97%; P = 0.02). On the other hand, type 2 tumors overall had more chromosomal alterations than type 1 tumors (P = 0.01), particularly gains of 1q (28 versus 3%; P = 0.02) and losses of 8p (33 versus 0%; P = 0.001), 11 (28 versus 3%; P = 0.02), and 18 (44 versus 9%; P = 0.01). Hierarchical clustering suggested cytogenetic patterns common but not restricted to type 2 morphology, one characterized by multiple additional gains, and another predominantly showing additional losses. These findings provide genetic evidence that type 1 and type 2 tumors arise from common cytogenetic pathways and that type 2 tumors evolve from type 1 tumors. Independently of type, losses of 9p were statistically correlated with advanced disease (P = 0.0008) and may serve as a potential adverse prognostic marker in papillary renal cell carcinomas.

Behavioral economics survey of patients with type 1 and type 2 diabetes

PubMed Central

Emoto, Naoya; Okajima, Fumitaka; Sugihara, Hitoshi; Goto, Rei

2015-01-01

Background Adherence to treatment and the metabolic control of diabetes are challenging in many patients with diabetes. The theory of neuroeconomics can provide important clues for understanding unreasonable human behavior concerning decisions between outcomes occurring at different time points. Objective We investigated patients with type 1 and type 2 diabetes to determine whether patients who are at a risk of developing complications are less risk averse. We also examined whether patients with type 1 and type 2 diabetes have different behavioral traits in decision making under risk. Methods We conducted a behavioral economics survey of 219 outpatients, 66 with type 1 diabetes and 153 with type 2 diabetes. All patients had been referred by general practitioners or other departments in the hospital. At the time of the survey, levels of hemoglobin A1c were not significantly different between patients with type 1 and type 2 diabetes. Results Patients with type 2 diabetes showed a lower response rate to the survey compared with patients with type 1 diabetes (71.9% vs 87.9%, P<0.01). Logistic regression analysis indicated that diabetic retinopathy was negatively associated with risk averse in pricing of hypothetical lotteries, myopic time preference, willingness to pay for preventive medicine, and levels of satisfaction with life. Diabetic nephropathy was also negatively associated with risk averse in pricing of hypothetical lotteries. Detailed analysis revealed that a lower proportion of patients with type 2 diabetes (22.7%) were categorized as risk averse compared with patients with type 1 diabetes (43.1%, P<0.05) in hypothetical lottery risk estimation. Conclusion This is the first report that investigated patients with diabetes in a clinical setting using a method based on behavioral economics. The results suggest that the attitude of patients toward risk plays an important role in the progress of the complications of diabetes. Different educational and

Behavioral economics survey of patients with type 1 and type 2 diabetes.

PubMed

Emoto, Naoya; Okajima, Fumitaka; Sugihara, Hitoshi; Goto, Rei

2015-01-01

Adherence to treatment and the metabolic control of diabetes are challenging in many patients with diabetes. The theory of neuroeconomics can provide important clues for understanding unreasonable human behavior concerning decisions between outcomes occurring at different time points. We investigated patients with type 1 and type 2 diabetes to determine whether patients who are at a risk of developing complications are less risk averse. We also examined whether patients with type 1 and type 2 diabetes have different behavioral traits in decision making under risk. We conducted a behavioral economics survey of 219 outpatients, 66 with type 1 diabetes and 153 with type 2 diabetes. All patients had been referred by general practitioners or other departments in the hospital. At the time of the survey, levels of hemoglobin A1c were not significantly different between patients with type 1 and type 2 diabetes. Patients with type 2 diabetes showed a lower response rate to the survey compared with patients with type 1 diabetes (71.9% vs 87.9%, P<0.01). Logistic regression analysis indicated that diabetic retinopathy was negatively associated with risk averse in pricing of hypothetical lotteries, myopic time preference, willingness to pay for preventive medicine, and levels of satisfaction with life. Diabetic nephropathy was also negatively associated with risk averse in pricing of hypothetical lotteries. Detailed analysis revealed that a lower proportion of patients with type 2 diabetes (22.7%) were categorized as risk averse compared with patients with type 1 diabetes (43.1%, P<0.05) in hypothetical lottery risk estimation. This is the first report that investigated patients with diabetes in a clinical setting using a method based on behavioral economics. The results suggest that the attitude of patients toward risk plays an important role in the progress of the complications of diabetes. Different educational and psychological approaches may be necessary to assess

Gaussian-Type Orbitals versus Slater-Type Orbitals: A Comparison

ERIC Educational Resources Information Center

Magalha~es, Alexandre L.

2014-01-01

The advantages of Gaussian-type orbitals (GTO) over Slater-type orbitals (STO) in quantum chemistry calculations are clarified here by means of a holistic approach. The popular Microsoft Office Excel program was used to create an interactive application with which students are able to explore the features of GTO, including automatic calculations…

Molecular binding mechanisms of aqueous cadmium and lead to siderophores, bacteria and mineral surfaces

NASA Astrophysics Data System (ADS)

Mishra, Bhoopesh

sphere sorption of Pb on kaolinite surface at acidic and circumneutral pH conditions respectively. In the presence of DFO-B, bulk sorption studies indicated that Pb sorption is enhanced in the presence of DFO-B around pH 6 and inhibited above pH 6.5. This was confirmed by x-ray fluorescence measurements. Extended XAFS study clearly indicated unwrapping of DFO-B molecule at the surface. Our study has unambiguously recognized it as a "Type A" ternary complex ("Type A" complex means surface-metal-ligand type of interaction). Taken together, bulk adsorption measurements and XAFS experiments represent a powerful approach for determining and modeling metal speciation and adsorption.

Infrared Spectroscopy for Rapid Characterization of Drill Core and Cutting Mineralogy

NASA Astrophysics Data System (ADS)

Calvin, W. M.; Kratt, C.; Kruse, F. A.

2009-12-01

Water geochemistry can vary with depth and location within a geothermal reservoir, owing to natural factors such as changing rock type, gas content, fluid source and temperature. The interaction of these variable fluids with the host rock will cause well known changes in alteration mineral assemblages that are commonly factored into the exploration of hydrothermal systems for economic metals, but are less utilized with regard to mapping borehole geology for geothermal energy production. Chemistry of geothermal fluids and rock alteration products can impact production factors such as pipeline corrosion and scaling and early studies explored the use of both silica and chlorites as geothermometers. Infrared spectroscopy is particularly good at identifying a wide variety of alteration minerals, especially in discrimination among clay minerals, with no sample preparation. The technique has been extensively used in the remote identification of materials, but is not commonly used on drill core or chips. We have performed several promising pilot studies that suggest the power of the technique to sample continuously and provide mineral logs akin to geophysical ones. We have surveyed a variety of samples, including drill chip boards, boxed core, and drill cuttings from envelopes, sample bottles and chip trays. This work has demonstrated that core and drill chips can be rapidly surveyed, acquiring spectra every few to tens of cm of section, or the vertical resolution of the chip tray (typically 10 feet). Depending on the sample type we can acquire spectral data over thousands of feet depth at high vertical resolution in a fraction of the time that is needed for traditional analytical methods such as XRD or TEM with better accuracy than traditional geologic drill or chip logging that uses visual inspection alone. We have successfully identified layered silicates such as illite, kaolinite, montmorillonite chlorite and prehnite, zeolites, opal, calcite, jarosite and iron oxides

The different neighbours around Type-1 and Type-2 active galactic nuclei

NASA Astrophysics Data System (ADS)

Villarroel, Beatriz; Korn, Andreas J.

2014-06-01

One of the most intriguing open issues in galaxy evolution is the structure and evolution of active galactic nuclei (AGN) that emit intense light believed to come from an accretion disk near a super massive black hole. To understand the zoo of different AGN classes, it has been suggested that all AGN are the same type of object viewed from different angles. This model--called AGN unification--has been successful in predicting, for example, the existence of hidden broad optical lines in the spectrum of many narrow-line AGN. But this model is not unchallenged and it is debatable whether more than viewing angle separates the so-called Type-1 and Type-2 AGN. Here we report the first large-scale study that finds strong differences in the galaxy neighbours to Type-1 and Type-2 AGN with data from the Sloan Digital Sky Survey (SDSS; ref. ) Data Release 7 (DR7; ref. ) and Galaxy Zoo. We find strong differences in the colour and AGN activity of the neighbours to Type-1 and Type-2 AGN and in how the fraction of AGN residing in spiral hosts changes depending on the presence or not of a neighbour. These findings suggest that an evolutionary link between the two major AGN types might exist.

Aggregation of Montmorillonite and Organic Matter in Aqueous Media Containing Artificial Seawater

DTIC Science & Technology

2009-01-23

laboratory kaolinite and montmorillonite aggregation in which the dispersion-aggregation properties of pure clay suspensions were found to be primarily...Article 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Aggregation of montmorillonite and organic matter in aqueous media containing...properties of suspended colloids and aggregates) were determined for systems containing suspended montmorillonite , humic acid, and/or chitin at the

Chemical Mechanisms of Toxic Solute Interactions with Soil Constituents

DTIC Science & Technology

1993-04-01

been widely reported (References 125-127). However, in days such as montmorillonite and kaolinite , whose cations have been (partially) exchanged with...matrix-isolation methods were used to characterize the sorption of water and fuel compounds on a model soil consisting of montmorillonite clay. The...only under very dry conditions. 14. SUBJECT TERMS Montmorillonite clay, fuels, infrared 15 NUMBER Of PAGES spectroscopy, ultraviolet-visible

Montmorillonite Functionalized with Pralidoxime as a Material for Chemical Protection against Organophosphorous Compounds

DTIC Science & Technology

2011-03-25

implied is via iondipole forces.5,6 It is well-known that clays such as montmorillonite and kaolinite accelerate the degradation of insecticides such...REPORT Montmorillonite Functionalized with Pralidoxime As a Material for Chemical Protection against Organophosphorous Compounds 14. ABSTRACT 16...SECURITY CLASSIFICATION OF: Montmorillonite K-10 functionalized with ?-nucleophilic 2-pralidoxime (PAM) and its zwitterionic oximate form (PAMNa) is

Particle size and X-ray analysis of Feldspar, Calvert, Ball, and Jordan soils

NASA Technical Reports Server (NTRS)

Chapman, R. S.

1977-01-01

Pipette analysis and X-ray diffraction techniques were employed to characterize the particle size distribution and clay mineral content of the feldspar, calvert, ball, and jordan soils. In general, the ball, calvert, and jordan soils were primarily clay size particles composed of kaolinite and illite whereas the feldspar soil was primarily silt-size particles composed of quartz and feldspar minerals.

Weather types in the South Shetlands (Antarctica) using a circulation type approach

NASA Astrophysics Data System (ADS)

Mora, Carla; João Rocha, Maria; Dutra, Emanuel; Trigo, Isabel; Vieira, Gonçalo; Fragoso, Marcelo; Ramos, Miguel

2010-05-01

Weather types in the South Shetlands (Antarctica) were defined using an automated method based on the Lamb Weather Type classification scheme (Jones et al. 1993). This is an objective classification originally developed for the British Isles (Jones et al., 1993) and also applied to southeast (Goodess and Palutikof 1998) and northwest Spain (Lorenzo et al, 2009), Portugal (Trigo and DaCamara 2000) and Greece (Maheras et al. 2004) with good results. Daily atmospheric circulation in the South Shetlands region from 1989 to 2009 was classified using a 16-node grid of sea level pressure data from the ERA Interim. The classification is obtained through the comparison of the magnitudes of the directional and rotational components of the geostrophic flow. Basic circulation types were combined into 10 groups of weather types: four directional types (NW, N, S and SW), three anticyclonic types (A, ASW and ANW), and three cyclonic types (C, CSW and CNW). Westerly flow and cyclonic circulation are the most frequent events throughout the year. The sea level pressure field for each weather type is presented and the synoptic characteristics are described. The analysis is based on ERA-Interim fields, including mean sea level pressure, precipitation, cloud cover, humidity and air temperature. Snow thickess modelled using HTESSEL is also considered. Analysis of variance (anova) and multivariate analysis (principal component analysis) are applied to evaluate the characteristics of each weather type. This circulation-type approach showed good results in the past for the downscaling of precipitation in other regions, and we are interested in evaluating the possibilities that the classification offers for downscaling precipitation, but also for snow and air temperature. For this we will be using observational data at test sites in Livingston and Deception islands. We are also motivated by the possibility of using the circulation-type approach as a predictor in statistical downscaling

HIGH TEMPERATURE INTERACTIONS BETWEEN RESIDUAL OIL ASH AND DISPERSED KAOLINITE POWDERS

EPA Science Inventory

The potential use of sorbents to manage ultrafine ash aerosol emissions from residual oil combustion was investigated using a downfired 82-kW-rated laboratory-scale refractory-lined combustor. The major constituents were vanadium (V), iron (Fe), nickel, (Ni) and zinc (Zn). Of the...

Effect of Particle Association on 2,2'-Bipyridyl Adsorption onto Kaolinite.

PubMed

Helmy, A. K.; Ferreiro, E. A.; de Bussetti, S. G.

2000-05-15

The effect of particle concentration, in kaolin suspensions, on the adsorption of 2,2'-bipyridyl was studied. Adsorption expressed in units of micromoles per gram decreased as a result of the increase in particle concentration and also as a result of the presence of coagulant (0.25 M NaCl). Dispersion treatment with sodium hexametaphosphate increased the adsorption of bipyridyl. The decrease in adsorption with the increase in particle concentration suggests a possible relation between adsorption and flocculation phenomena. On the basis of classic flocculation theory a straight-line relation was obtained between the square root of the adsorption maximum (mmol/L) and particle concentration (g/L). It is concluded that particle association, which is a function of particle concentration, reduces the surface/aqueous interface and consequently the adsorption of bipyridyl. Copyright 2000 Academic Press.

TypingSuite: Integrated Software for Presenting Stimuli, and Collecting and Analyzing Typing Data

ERIC Educational Resources Information Center

Mazerolle, Erin L.; Marchand, Yannick

2015-01-01

Research into typing patterns has broad applications in both psycholinguistics and biometrics (i.e., improving security of computer access via each user's unique typing patterns). We present a new software package, TypingSuite, which can be used for presenting visual and auditory stimuli, collecting typing data, and summarizing and analyzing the…

Type A and type B botulism in the North: first reported cases due to toxin other than type E in Alaskan Inuit.

PubMed Central

Barrett, D. H.; Eisenberg, M. S.; Bender, T. R.; Burks, J. M.; Hatheway, C. L.; Dowell, V. R.

1977-01-01

Botulism outbreaks shown to be due to type A and type B toxin occurred in Alaska, a region previously known for only type E botulism. The outbreak due to type A toxin involved three people, two of whom died. The outbreak due to type B toxin involved nine people, none of whom died. Both outbreaks were in Inuit villages, and native foods were incriminated. The occurrence of these outbreaks strongly suggests that Clostridium botulinum, types A and B are indigenous to Alaska. The outbreaks underscore the need for initial treatment of patients with antitoxin that is trivalent (ABE), even in Arctic regions. PMID:332309

Virulence gene typing of methicillin-resistant Staphylococcus aureus as a complement in epidemiological typing.

PubMed

Nowrouzian, Forough L; Karami, Nahid; Welinder-Olsson, Christina; Ahrén, Christina

2013-06-01

Methicillin-resistant Staphylococcus aureus (MRSA) has widely spread to all parts of the world. For surveillance and effective infection control molecular typing is required. We have evaluated the utility of virulence gene determination as a complementary tool for epidemiological typing of MRSA in relation to spa-typing and pulsed-field gel electrophoresis (PFGE). We assessed 63 community-acquired MRSA (CA-MRSA) isolates detected in the West part of Sweden for 30 virulence factor genes (VF) and agr allele variations by serial polymerase chain reaction (PCR) assays. These isolates belonged to sequence types (ST) 8, 80, 45 and 30 as classified by multilocus sequence typing. The isolates in each spa-type and PFGE-type were examined over an extended time-period and constituted a varying number of PFGE-subtypes (5-14) and spa-types (3-11) within four major PFGE types. Each ST had a unique VF profile. For isolates within a major PFGE type showing high diversity both in PFGE subtypes and spa the VF profile varied as well in contrast to those with low diversity where no alterations were seen. Thus, the accuracy of each typing method does not only vary by the method per se but is rather dependent on the genetic repertoire of the typed strains and genes evaluated. For strains demonstrating high diversity VF typing may be a useful complement in the epidemiological investigations, and may highlight the accurate discriminatory power of spa or PFGE typing. Copyright © 2013 Elsevier B.V. All rights reserved.

Comparison of diabetic ketoacidosis in patients with type-1 and type-2 diabetes mellitus.

PubMed

Barski, Leonid; Nevzorov, Roman; Harman-Boehm, Ilana; Jotkowitz, Alan; Rabaev, Elena; Zektser, Miri; Zeller, Lior; Shleyfer, Elena; Almog, Yaniv

2013-04-01

Diabetic ketoacidosis (DKA) occurs most often in patients with type 1 diabetes, however patients with type 2 diabetes are also susceptible to DKA under stressful conditions. The aims of our study were to evaluate and compare the clinical and biochemical characteristics and outcomes of type 1 versus type 2 diabetes mellitus (DM) patients with DKA. A retrospective cohort study of adult patients hospitalized with DKA between January 1, 2003, and January 1, 2010. The clinical and biochemical characteristics of DKA patients with type-1 DM were compared with those of patients with type-2 DM. The primary outcome was in-hospital all-cause mortality. The study cohort included 201 consecutive patients for whom the admission diagnosis was DKA: 166 patients (82.6%) with type-1 DM and 35 patients (17.4%) with type-2 DM. The patients with DKA and type-2 DM were significantly older than patients with type-1 DM (64.3 versus 37.3, P < 0.001). Significantly more patients with severe forms of DKA were seen in the group with type-2 DM (25.7% versus 9.0%, P = 0.018). The total in-hospital mortality rate of patients with DKA was 4.5%. The primary outcome was significantly worse in the group of patients with type-2 DM. DKA in patients with type-2 DM is a more severe disease with worse outcomes compared with type-1 DM. Advanced age, mechanical ventilation and bed-ridden state were independent predictors of 30-day mortality.

Sex-typing behavior and sex-typing pressure in child/parent interaction.

PubMed

Jacklin, C N; DiPietro, J A; Maccoby, E E

1984-10-01

The sex-typing of children and the sex-typing pressure of parents was investigated during free play in a home visit. There were 30 male and 24 female 45-month-olds observed with their mothers and fathers in separate free-play sessions during which an array of both sex-stereotyped and neutral toys were available. Behavioral observations were recorded for a variety of parent, child, and dyadic behaviors, including initiations of sex-typed play, total sex-typed play, and rough-and-tumble play. Children initiated sex-typed play and played with sex-appropriate toys. Father-child and mother-daughter dyads were more likely to engage in thematic play appropriate to the child's sex, while in mother-son dyads equal amounts of masculine and feminine play occurred. In addition father-son dyads displayed the highest levels of rough-and tumble play and arousal of child by parent. The results suggest that fathers are the discriminating influence on sex-appropriate play.

P-type gallium nitride

DOEpatents

Rubin, M.; Newman, N.; Fu, T.; Ross, J.; Chan, J.

1997-08-12

Several methods have been found to make p-type gallium nitride. P-type gallium nitride has long been sought for electronic devices. N-type gallium nitride is readily available. Discovery of p-type gallium nitride and the methods for making it will enable its use in ultraviolet and blue light-emitting diodes and lasers. pGaN will further enable blue photocathode elements to be made. Molecular beam epitaxy on substrates held at the proper temperatures, assisted by a nitrogen beam of the proper energy produced several types of p-type GaN with hole concentrations of about 5{times}10{sup 11} /cm{sup 3} and hole mobilities of about 500 cm{sup 2} /V-sec, measured at 250 K. P-type GaN can be formed of unintentionally-doped material or can be doped with magnesium by diffusion, ion implantation, or co-evaporation. When applicable, the nitrogen can be substituted with other group III elements such as Al. 9 figs.

P-type gallium nitride

DOEpatents

Rubin, Michael; Newman, Nathan; Fu, Tracy; Ross, Jennifer; Chan, James

1997-01-01

Several methods have been found to make p-type gallium nitride. P-type gallium nitride has long been sought for electronic devices. N-type gallium nitride is readily available. Discovery of p-type gallium nitride and the methods for making it will enable its use in ultraviolet and blue light-emitting diodes and lasers. pGaN will further enable blue photocathode elements to be made. Molecular beam epitaxy on substrates held at the proper temperatures, assisted by a nitrogen beam of the proper energy produced several types of p-type GaN with hole concentrations of about 5.times.10.sup.11 /cm.sup.3 and hole mobilities of about 500 cm.sup.2 /V-sec, measured at 250.degree. K. P-type GaN can be formed of unintentionally-doped material or can be doped with magnesium by diffusion, ion implantation, or co-evaporation. When applicable, the nitrogen can be substituted with other group III elements such as Al.

The role of MIF in type 1 and type 2 diabetes mellitus.

PubMed

Sánchez-Zamora, Yuriko I; Rodriguez-Sosa, Miriam

2014-01-01

Autoimmunity and chronic low-grade inflammation are hallmarks of diabetes mellitus type one (T1DM) and type two (T2DM), respectively. Both processes are orchestrated by inflammatory cytokines, including the macrophage migration inhibitory factor (MIF). To date, MIF has been implicated in both types of diabetes; therefore, understanding the role of MIF could affect our understanding of the autoimmune or inflammatory responses that influence diabetic pathology. This review highlights our current knowledge about the involvement of MIF in both types of diabetes in the clinical environment and in experimental disease models.

Types of Diabetes

MedlinePlus

... most common form of diabetes. People can develop type 2 diabetes at any age. Being overweight and inactive increases the chances of developing type 2 diabetes. Treatment includes taking diabetes medicines, making wise food ...

Study on Al2O3 extraction from activated coal gangue under different calcination atmospheres

NASA Astrophysics Data System (ADS)

Dong, Ling; Liang, Xinxing; Song, Qiang; Gao, Gewu; Song, Lihua; Shu, Yuanfeng; Shu, Xinqian

2017-12-01

Coal gangue was calcinated under air, nitrogen, carbon dioxide, air-hydrogen, and hydrogen atmospheres. The effects of different calcination temperatures and atmospheres on the mineral composition of activated coal gangue were investigated by X-ray diffraction. Moreover, the acid leaching kinetics of aluminum oxide from coal gangue was investigated with sulfuric acid. It showed that the air atmosphere promoted kaolinite decomposition during coal gangue calcination. The hydrogen atmosphere promoted the activation and decomposition of kaolinite at reaction temperatures exceeding 650°C. The carbon dioxide atmosphere eliminated the influence of residual carbon on coal gangue. When the ratio of acid/coal gangue was 1.5 and reaction temperature was 650°C, the sulfuric acid leaching rate under air, air-hydrogen, carbon dioxide, hydrogen and nitrogen atmospheres were 93.66%, 90.90%, 84.06%, 81.91% and 77.54% respectively. The acid leaching reaction process conformed to unreacted shrinking core model of particle unchanged, and was controlled by the interfacial chemical reaction. The reaction kinetic equation for the leaching process was 1-(1-x)1/3=kt with an apparent activation energy of 48.97 kJ/mol.

Contents and occurrence of cadmium in the coals from Guizhou province, China.

PubMed

Song, Dangyu; Wang, Mingshi; Zhang, Junying; Zheng, Chuguang

2008-10-01

Eleven raw coal samples were collected from Liuzhi, Suicheng, Zunyi, Xingren, Xingyi, and Anlong districts in Guizhou Province, Southwest China. The content of cadmium (Cd) in coal was determined using inductively coupled plasma mass-spectrometry (ICP-MS). Cd contents ranged from 0.146 to 2.74 ppm (whole coal basis), with an average of 1.09 ppm. In comparison with the arithmetic means of Cd in Chinese coal (0.25 ppm), this is much higher. In order to find its occurrence in coal, float-sink analysis and a coal flotation test by progressive release were conducted on two raw coal samples. The content of the Cd and ash yield of the flotation products were determined. The organic matter was removed by low-temperature ashing (LTA). X-ray diffraction (XRD) was used to differentiate the main, minor, and trace minerals in the LTA from different flotation subproducts. Quartz, kaolinite, pyrite, and calcite were found to dominate the mineral matters, with a proportion of anatase, muscovite, and illite. Then quantitative analysis of minerals in LTA was conducted using material analysis using diffraction (MAUD) based on the Rietveld refinement method. Results show that Cd has a strong association with kaolinite.

Mössbauer spectroscopy and X-ray diffraction analyses of clayey samples used as ceramic sourcing materials, in Peru

NASA Astrophysics Data System (ADS)

Quille, Rubén; Bustamante, Ángel; Palomino, Ybar

2011-11-01

The ceramic industry is an important area of economic activity in the Ayacucho Region, in particular in the District of Quinua. As a consequence, there is a huge demand for clay to produce ceramic pastes in that region. This paper reports on results concerning the mineralogical characterization of four clayey samples, which were collected MAA and SPQA from the area Pampa de La Quinua with geographic coordinates 13° 02' 49″ S 74° 08' 03″ W, CE1M and CE2M from the Quinua locality 13° 03' 07″ S 74° 08' 31″ W, both in the District of Quinua, Province of Huamanga, Ayacucho, Peru. The chemical and mineralogical characterization of these samples was carried out with powder X-ray diffraction detecting quartz, albite, montmorillonite, kaolinite and glauconite mineral phases, Mössbauer spectroscopy detected iron in kaolinite, glauconite and montmorillonite minerals. Chemical analysis was performed through scanning electron microscopy and energy dispersive X-ray spectroscopy. Data obtained from the combination of these techniques provided relevant information about the morphology, chemical composition, and the mineralogy of samples.

PdNP Decoration of Halloysite Lumen via Selective Grafting of Ionic Liquid onto the Aluminol Surfaces and Catalytic Application.

PubMed

Dedzo, Gustave K; Ngnie, Gaëlle; Detellier, Christian

2016-02-01

The synthesis of selectively deposited palladium nanoparticles (PdNPs) inside tubular halloysite lumens is reported. This specific localization was directed by the selective modification of the aluminol surfaces of the clay mineral through stable Al-O-C bonds. An ionic liquid (1-(2-hydroxyethyl)-3-methylimidazolium) was grafted onto halloysite following the guest displacement method (generally used for kaolinite) using halloysite-DMSO preintercalate. The characterization of this clay nanohybrid material (XRD, NMR, TGA) showed characteristics reminiscent of similar materials synthesized from kaolinite. The grafting on halloysite lumens was also effective without using the DMSO preintercalate. The presence of these new functionalities in halloysite directs the synthesis of uniform PdNPs with size ranging between 3 and 6 nm located exclusively in the lumens. This results from the selective adsorption of PdNPs precursors in functionalized lumens through an anion exchange mechanism followed by in situ reduction. In contrast, the unmodified clay mineral displayed nanoparticles both inside and outside the tubes. These catalysts showed significant catalytic activity for the reduction of 4-nitrophenol (4-NP). The most efficient catalysts were recycled up to three times without reducing significantly the catalytic activities.

Using an Engineered Protein Model to Constrain Protein-Mineral Interactions

NASA Astrophysics Data System (ADS)

Chacon, S. S.; Reardon, P. N.; Washton, N.; Kleber, M.

2015-12-01

Exoenzymes are proteins that can catalyze the depolymerization of soil organic matter (SOM). Proteins can also be an important source of organic N for microorganisms, but must be fragmented into small peptides in order to be transported through their membranes. An exoenzyme's affinity to mineral surfaces found in soil affects their capacity to degrade SOM or other proteins. Our goal was to determine the range of modifications on proteins when they interact with a mineral surface. We hypothesized that pedogenic oxides would fragment or promote greater chemical modifications to a protein than phyllosilicates. A well-characterized protein proxy (Gb1, IEP 4.0, 6.2 kDA) was adsorbed onto functionally different mineral surfaces (goethite, montmorillonite, kaolinite and birnesite) at pH 5 and pH 7. We then generated three engineered proxies of Gb1 by inserting either negatively charged, positively charged or aromatic amino acids into the second loop. We used liquid chromatography coupled with a mass spectrometer (LC-MS/MS) and solution-state Heteronuclear Single Quantum Coherence Spectroscopy Nuclear Magnetic Resonance (HSQC NMR) to observe modifications to Gb1 that was allowed to equilibrate during the adsorption process for kaolinite, goethite, birnessite, and montmorillonite. We also used Helium Ion Microscopy (HIM) to determine which surface archetypes Gb1 preferentially adsorbed to as a function of the mineral type. The three engineered proxies were used to determine how variation of the amino acid sequence affects a protein interaction with a mineral surface. Preliminary results in the LC-MS/MS indicate that birnessite hydrolytically fragments Gb1 into polypeptides. Our results suggest that not all mineral surfaces in soil may act as sorbents for EEs and that chemical modification of their structure should also be considered as an explanation for decrease in EE activity. Our results also indicate an abiotic pathway for the turnover of proteins, although its relative

Mineralogical, chemical, and physical properties of the regolith overlying crystalline rocks, Fairfax County, Virginia: a preliminary report

USGS Publications Warehouse

Leo, Gerhard W.; Pavich, M.J.; Obermeier, Stephen F.

1977-01-01

Undisturbed cores of saprolite developed on crystalline rocks of the Piedmont Province in Fairfax County, Virginia have been obtained using a combination of Shelby tubes, Denison sampler, and modified diamond core-drilling. The principal purpose of the core study is to correlate variations in chemistry, mineralogy and texture with engineering properties throughout the weathering profile. Coring sites were chosen to obtain a maximum depth of weathering on diverse lithologies. The rocks investigated include pelitic schist, metagraywacke, granite, diabase and serpentinite. Four to twelve samples per core were selected, depending on thickness of 1) the weathering profile (from about 1 m in serpentinite to more than 30 m in pelitic schist) and on 2) megascopic changes in saprolite character for analysis of petrography, texture, clay mineralogy andd major element chemistry. Shear strength and compressibility were determined on corresponding segments of core. Standard penetration tests were performed adjacent to coring sites to evaluate engineering properties in situ. Geochemical changes of saprolite developed from each rock type follow predictable trends from fresh rock to soil profile, with relative Increases in Si, Ti, Al, Fe3+ and H20; variable K; and relative loss of Fe 2+, Mg, Ca, and Na. These variations are more pronounced in the weathering profiles over mafic and ultramafic rocks than metagraywacke. Clay minerals in granite, schist and metagraywacke saprolite are kaolinite, dioctahedral vermiculite, interlayered micavermiculite, and minor illite. Gibbsite is locally developed in near-surface samples of schist. Standard penetration test data for the upper 7 m of saprolite over schist and metagraywacke suggest alternations between stronger and weaker horizons than probably reflect variations in lithology including the presence of quartz lenses. Results for granite saprolite are most consistent but indicate lower strength. Shear strength increases fairly regularly

Maternal Type A behavior during pregnancy, neonatal crying, and early infant temperament: do type A women have type A babies?

PubMed

Parker, S J; Barrett, D E

1992-03-01

It was hypothesized that type A behavior in pregnant women would be associated with increased neonatal crying and differential reports of infant temperament at 3 months. Type A behaviors during pregnancy were measured in a self-selected cohort of 72 healthy, primiparous, middle-class women. Their newborns were assessed at 48 hours of age and the women completed an infant temperament questionnaire at 3 months. Women who were classified as type A on the Job Involvement scale of the Jenkins Activity Survey had infants who cried more during a standardized neurobehavioral assessment compared with infants of women who were type B on the same scale. Women who were type A for Job Involvement rated their 3-month-old infants as more intense and less predictable in their responses to the environment. They were also more likely to be breast-feeding their infants at 3 months. This is the first study to examine the prevalence and nature of maternal type A behaviors during pregnancy and to show their relationship to neonatal crying behavior, to maternal report of early infant temperament, and to maternal breast-feeding.

Type 2 diabetes mellitus coincident with pulmonary tuberculosis is associated with heightened systemic type 1, type 17, and other proinflammatory cytokines.

PubMed

Kumar, Nathella Pavan; Sridhar, Rathinam; Banurekha, Vaithilingam V; Jawahar, Mohideen S; Fay, Michael P; Nutman, Thomas B; Babu, Subash

2013-10-01

Type 2 diabetes mellitus is a major risk factor for the development of active tuberculosis, although the biological basis underlying this susceptibility remains poorly characterized. To identify the influence of coincident diabetes mellitus on cytokine levels in pulmonary tuberculosis, we examined circulating levels of a panel of cytokines and chemokines in the plasma of individuals with tuberculosis with diabetes and compared them with those of individuals without diabetes. Tuberculosis with diabetes is characterized by elevated circulating levels of type 1 (IFN-γ, tumor necrosis factor-α, and IL-2), type 2 (IL-5), and type 17 (IL-17A) cytokines but decreased circulating levels of IL-22. This was associated with increased systemic levels of other proinflammatory cytokines (IL-1β, IL-6, and IL-18) and an antiinflammatory cytokine (IL-10) but not type 1 IFNs. Moreover, tuberculosis antigen-stimulated whole blood also showed increased levels of proinflammatory cytokines. Finally, type 1 and type 17 cytokines in plasma exhibit a significant positive correlation with hemoglobin A1C levels, indicating that impaired control of diabetes is associated with this proinflammatory milieu. Multivariate analysis revealed that the association of proinflammatory cytokines with diabetes mellitus was not influenced by age, sex, or other metabolic parameters. Our data reveal that tuberculosis with diabetes is characterized by heightened cytokine responsiveness, indicating that chronic inflammation underlying type 2 diabetes potentially contributes to increased immune pathology and poor control in tuberculosis infection.

Diabetes Type 1

MedlinePlus

Diabetes means your blood glucose, or blood sugar, levels are too high. With type 1 diabetes, your pancreas does not make insulin. Insulin is ... kidneys, nerves, and gums and teeth. Type 1 diabetes happens most often in children and young adults ...

Liquid-type Botulinum Toxin Type A in Adductor Spasmodic Dysphonia: A Prospective Pilot Study.

PubMed

Cha, Wonjae; Jang, Jeon Yeob; Wang, Soo-Geun; Kang, Ji-Heon; Jo, Min-Gyu

2017-05-01

Botulinum toxin (BTX) has been widely used to treat adductor spasmodic dysphonia (ADSD). Most commercially available forms of BTX require reconstitution before use, which may increase the risk of contamination and requires careful titration. Recently, a liquid-type BTX type A (BTX-A) has been developed, which should simplify the procedure and enhance its efficacy. Herein, we present a prospective pilot study to investigate the efficacy and safety of liquid-type BTX-A in the treatment of ADSD. Twenty-six consecutive liquid-type BTX-A injections were performed in 12 patients with ADSD. We included as a control group 34 consecutive patients with ADSD who had previously undergone 52 vocal fold injection procedures with freeze-dried-type BTX-A. All patients in both groups had improvement of symptoms related to ADSD and period of normal voice. Most patients experienced breathiness, and the onset time, the peak response time, and the duration of breathiness were similar in both groups. The duration of effect (days) was 96.96 ± 18.91 and 77.38 ± 18.97 in the freeze-dried-type and the liquid-type groups, and the duration of benefit (days) was 80.02 ± 18.24 and 62.69 ± 19.73 in the freeze-dried-type and the liquid-type groups. To compare the efficacy between the freeze-dried-type and the liquid-type BTX-A, the sessions of the unilateral vocal fold injection were included and were categorized as group A (1 ~ 2 units BTX-A) and group B (2 ~ 3 units BTX-A), according to the dose per vocal fold. There was no significant difference of effect time between freeze-dried-type and liquid-type BTX-A groups. No adverse events related to BTX or vocal fold injection were reported. Liquid-type BTX-A is safe and effective for the treatment of spasmodic dysphonia. With the advantages of simple preparation, storage, and reuse and animal protein-free constituents, liquid-type BTX-A may be a good option in the treatment of spasmodic dysphonia. Copyright © 2017 The

Pediatric obesity & type 2 diabetes.

PubMed

Dea, Tara L

2011-01-01

This article focuses on (a) identifying obesity and other risk factors for developing type 2 diabetes, (b) differentiating between pediatric type 1 diabetes and type 2 diabetes, and (c) treating pediatric type 2 diabetes. Obesity has significant implications on a child's health, including an increased risk for insulin resistance and progression to type 2 diabetes. Type 2 diabetes in children, characterized by insulin resistance and relative pancreatic b-cell failure due to the increased demand for insulin production, has now reached epidemic proportions. Longitudinal research on pediatric type 2 diabetes, however, is lacking because this epidemic is relatively new. Treatment of type 2 diabetes in children is focused on lifestyle modification with weight management/increased physical activity, and pharmacological management through oral medication or insulin therapy. Because children with type 2 diabetes are at risk for developing diabetes-related complications earlier in life, they need to be closely monitored for comorbidities.

Skeletal Metabolism, Fracture Risk, and Fracture Outcomes in Type 1 and Type 2 Diabetes

PubMed Central

Civitelli, Roberto; Hofbauer, Lorenz C.; Khosla, Sundeep; Lecka-Czernik, Beata; Schwartz, Ann V.

2016-01-01

Fracture risk is significantly increased in both type 1 and type 2 diabetes, and individuals with diabetes experience worse fracture outcomes than normoglycemic individuals. Factors that increase fracture risk include lower bone mass in type 1 diabetes and compromised skeletal quality and strength despite preserved bone density in type 2 diabetes, as well as the effects of comorbidities such as diabetic macro- and microvascular complications. In this Perspective, we assess the developing scientific knowledge regarding the epidemiology and pathophysiology of skeletal fragility in patients with diabetes and the emerging data on the prediction, treatment, and outcomes of fractures in individuals with type 1 and type 2 diabetes. PMID:27329951

Coevolution of patch-type dependent emigration and patch-type dependent immigration.

PubMed

Weigang, Helene C

2017-08-07

The three phases of dispersal - emigration, transfer and immigration - are affecting each other and the former and latter decisions may depend on patch types. Despite the inevitable fact of the complexity of the dispersal process, patch-type dependencies of dispersal decisions modelled as emigration and immigration are usually missing in theoretical dispersal models. Here, I investigate the coevolution of patch-type dependent emigration and patch-type dependent immigration in an extended Hamilton-May model. The dispersing population inhabits a landscape structured into many patches of two types and disperses during a continuous-time season. The trait under consideration is a four dimensional vector consisting of two values for emigration probability from the patches and two values for immigration probability into the patches of each type. Using the adaptive dynamics approach I show that four qualitatively different dispersal strategies may evolve in different parameter regions, including a counterintuitive strategy, where patches of one type are fully dispersed from (emigration probability is one) but individuals nevertheless always immigrate into them during the dispersal season (immigration probability is one). I present examples of evolutionary branching in a wide parameter range, when the patches with high local death rate during the dispersal season guarantee a high expected disperser output. I find that two dispersal strategies can coexist after evolutionary branching: a strategy with full immigration only into the patches with high expected disperser output coexists with a strategy that immigrates into any patch. Stochastic simulations agree with the numerical predictions. Since evolutionary branching is also found when immigration evolves alone, the present study is adding coevolutionary constraints on the emigration traits and hence finds that the coevolution of a higher dimensional trait sometimes hinders evolutionary diversification. Copyright © 2017

Interference with propagation of typing bacteriophages by extrachromosomal elements in Salmonella typhimurium: bacteriophage type 505.

PubMed Central

van Embden, J D; van Leeuwen, W J; Guinée, P A

1976-01-01

Samonella typhimurium bacteriophage type 505 is the most frequently encountered phage type in the Netherlands and its neighboring countries. Phage type 505 was analyzed with regard o the interference with propagation of the typing phages by the prophages and plasmids, present in the type strain S. typhimurium 505... Images PMID:783145

Efficient Type Representation in TAL

NASA Technical Reports Server (NTRS)

Chen, Juan

2009-01-01

Certifying compilers generate proofs for low-level code that guarantee safety properties of the code. Type information is an essential part of safety proofs. But the size of type information remains a concern for certifying compilers in practice. This paper demonstrates type representation techniques in a large-scale compiler that achieves both concise type information and efficient type checking. In our 200,000-line certifying compiler, the size of type information is about 36% of the size of pure code and data for our benchmarks, the best result to the best of our knowledge. The type checking time is about 2% of the compilation time.

Type A and hardiness.

PubMed

Kobasa, S C; Maddi, S R; Zola, M A

1983-03-01

The study examined the relationship between the Type A behavior pattern and personality hardiness and predicted an interaction between the two that would be influential for illness onset. Type A and hardiness were found to be conceptually different and empirically independent factors. Under high stressful life events, male executives who were high in Type A and low in hardiness tended toward higher general illness scores than any other executives. Type A and hardiness emerge from this study as bases for extrinsic and intrinsic motivation, respectively.

Personality types of entrepreneurs.

PubMed

Müller, Günter F; Gappisch, Cathrin

2005-06-01

85 German entrepreneurs were psychometrically assessed on 12 primary trait characteristics. The sample consisted of 49 men and 36 women whose mean age was 45.6 yr. (SD= 10.3). Occupational domains were production (40%) and services (60%). The mean duration of entrepreneurship within these domains was 13.1 yr. (SD=9.3). By factor analysis five personality types of entrepreneurs could be identified: Creative Acquisitor, Controlled Perseverator, Distant Achiever, Rational Manager, and Egocentric Agitator. These types correspond with types found in research by Miner and with the Myer-Briggs Indicator. In addition, correlations between general type potential and both job and life satisfaction of entrepreneurs were found. The results are discussed with regard to intercultural stability of personality types and implications for research and application.

Electrothermally-Actuated Micromirrors with Bimorph Actuators--Bending-Type and Torsion-Type.

PubMed

Tsai, Cheng-Hua; Tsai, Chun-Wei; Chang, Hsu-Tang; Liu, Shih-Hsiang; Tsai, Jui-Che

2015-06-22

Three different electrothermally-actuated MEMS micromirrors with Cr/Au-Si bimorph actuators are proposed. The devices are fabricated with the SOIMUMPs process developed by MEMSCAP, Inc. (Durham, NC, USA). A silicon-on-insulator MEMS process has been employed for the fabrication of these micromirrors. Electrothermal actuation has achieved a large angular movement in the micromirrors. Application of an external electric current 0.04 A to the bending-type, restricted-torsion-type, and free-torsion-type mirrors achieved rotation angles of 1.69°, 3.28°, and 3.64°, respectively.

Electrothermally-Actuated Micromirrors with Bimorph Actuators—Bending-Type and Torsion-Type

PubMed Central

Tsai, Cheng-Hua; Tsai, Chun-Wei; Chang, Hsu-Tang; Liu, Shih-Hsiang; Tsai, Jui-Che

2015-01-01

Three different electrothermally-actuated MEMS micromirrors with Cr/Au-Si bimorph actuators are proposed. The devices are fabricated with the SOIMUMPs process developed by MEMSCAP, Inc. (Durham, NC, USA). A silicon-on-insulator MEMS process has been employed for the fabrication of these micromirrors. Electrothermal actuation has achieved a large angular movement in the micromirrors. Application of an external electric current 0.04 A to the bending-type, restricted-torsion-type, and free-torsion-type mirrors achieved rotation angles of 1.69°, 3.28°, and 3.64°, respectively. PMID:26110409

The Effect of Suspended Sediment Transport and Deposition on Streambed Clogging Under Losing and Gaining Flow Conditions

NASA Astrophysics Data System (ADS)

Fox, A.; Packman, A. I.; Preziosi-Ribero, A.; Li, A.; Arnon, S.

2017-12-01

Sediment transport and deposition in streams can affect streambed hydraulic characteristics due to clogging, reduce water fluxes through the hyporheic zone, and thus expected to affect biogeochemical processes. Processes affecting deposition of suspended particles were systematically studied under various overlying velocities but without taking into account the interactions with groundwater. This is despite the fact that the interaction with groundwater were shown to play an important role in deposition patterns of fine sediments in field studies. The objective of this study was to evaluate the effect of losing and gaining fluxes on suspended sediment depositional patterns and on hyporheic exchange fluxes. Experiments were conducted in a laboratory flume system (640 cm long and 30 cm wide) that has a capacity to enforce losing or gaining flow conditions. The flume was packed with homogenous sand, while suspended sediment deposition was evaluated by adding kaolinite particles to the water and following the deposition rate by particle disappearance from the bulk water. Consecutive additions of kaolinite were done, while hyporheic exchange fluxes were evaluated by conducting NaCl tracer experiments between each kaolinite additions. Furthermore, dye injections were used to visualize the flow patterns in the streambed using time-lapse photography through the transparent sidewalls of the flume. Hyporheic exchange and particle tracking simulations were done to assess the results of particle deposition and feedbacks between hyporheic flow, particle transport, and streambed clogging. Experimental results showed that the deposition of clay decreases with increasing amount of clay concentration in the sediment. Hyporheic exchange flux decreases linearly with increasing amount of clay added to the system and the region of active hyporheic exchange was confined to the upper part of the sediment. Understanding the particle deposition mechanisms under losing and gaining flow

Estimation of landslide-triggering factors using clay minerals, ASTER satellite image and GIS in the Busan area, southeastern Korea

NASA Astrophysics Data System (ADS)

Jeong, G. C.; Kim, M. G.; Choi, J. J.; Ryu, J. O.; Nho, J. G.; Choo, C. O.

2016-12-01

This study aims at estimating landslide-inducing factors such as extreme rainfall, slope, and geological factors in Busan city, southeastern Korea, using clay mineralogy, DM analysis and DB construction in order to develop the landslide evaluation standards suitable for the country. GIS-based data collected from the study area include geological maps, topological maps, soil maps, forest maps and others in the DB construction. Data extraction and processing for landslide-induced factors consist of expandable clay minerals identified using XRD, along with XRF and weathering sensitivity analysis and fundamental soil analysis on 38 bulk samples composed of weathered rocks and soils. Finally landslide sensibility maps were constructed using ArcGIS, together with ASTER satellite images for identifying clay minerals on regional areas helpful for saving time and money. In Mt. Cheonma, 16 samples are composed of quartz, albite, illite, vermiculite, and kaolinite, with little difference in mineralogy. In Mt. Hwangryeong and Mt. Geumryeun, 12 samples consist of quartz, albite, illite, vermiculite, kaolinite and hornblende, with little difference in mineralogy. In Mt. Songhak, 10 samples are composed of quartz, illite, vermiculite, and kaolinite. Quartz, albite and illite are abundant in most samples, regardless of sites studied. IDW interpolation method was applied to the Busan area. The resolution of space grids consists of 5 m x 5 m. Especially, illite was used as the most effective factor that induces landslide using IDW interpolation and ASTER satellite images. In conclusion, sensibility maps constructed using 16 layers including illite content, weathered sensibility are well in accordance with the real sites where landslides took place, showing that areas with high sensibility are closely related to the high frequencies of landslide. This research was supported by the Public Welfare & Safety Research Program through the National Research Foundation of Korea (NRF) funded

Late Miocene to Pleistocene Mineralogy of ODP Site 1146

NASA Astrophysics Data System (ADS)

Arnold, E. M.

2001-12-01

ODP Site 1146 (19° 27.40'N, 116° 16.37'E, 2092 m depth) was drilled on the continental slope of the South China Sea. A composite section, comprised of three stratigraphic units, extends down to 640 mcd. Unit 1 is late Pliocene to Pleistocene nannofossil clay (0 - 243 mcd); Unit 2, middle Miocene to Late Pliocene foraminifera - nannofossil - clay mixed sediment (243 - 553 mcd); Unit 3, early to middle Miocene nannofossil clay (553 - 642 mcd). This study reports the < 2 μ m mineralogy from the late Miocene through early Pleistocene. Samples were analyzed at approximately 1.5 m intervals from 150 to 225 mcd, and 1 m intervals from 225 to 440 mcd, with an age resolution of ~25 ka and ~35 ka, respectively. Illite, chlorite, quartz and plagioclase concentrations decrease with increasing depth through Unit 1. Kaolinite and calcite concentrations increase with depth, while smectite values are constant in this unit. Illite, quartz and plagioclase show high variability in Unit 1 compared with the underlying Unit 2. Unit 2 has more uniform sediment composition, with constant illite, chlorite, and quartz concentrations. Kaolinite concentration increases with depth, following a drop in concentration across the Unit 1/2 boundary. Plagioclase concentration shows a small, steady decrease throughout this unit. Smectite concentration does not change across the Unit 1/2 boundary, decreases to a steady low value from 310 - 400 mcd, and increases again towards the bottom. The mineralogy of sediments recovered at Site 1146 suggest a classic pattern of source region aridification from the middle Pliocene through the Pleistocene, indicated in Unit 1 mineralogy as a decrease in kaolinite with decreasing depth, concomitant with an increase in quartz, plagioclase, illite and chlorite. The mineral variability in this interval suggests glacial - interglacial control of the terrigenous sedimentation. The sediment sources and source area weathering regimes were relatively constant throughout

Clay-mineral suites, sources, and inferred dispersal routes: Southern California continental shelf

USGS Publications Warehouse

Hein, J.R.; Dowling, J.S.; Schuetze, A.; Lee, H.J.

2003-01-01

Clay mineralogy is useful in determining the distribution, sources, and dispersal routes of fine-grained sediments. In addition, clay minerals, especially smectite, may control the degree to which contaminants are adsorbed by the sediment. We analyzed 250 shelf sediment samples, 24 river-suspended-sediment samples, and 12 river-bed samples for clay-mineral contents in the Southern California Borderland from Point Conception to the Mexico border. In addition, six samples were analyzed from the Palos Verdes Headland in order to characterize the clay minerals contributed to the offshore from that point source. The <2 ??m-size fraction was isolated, Mg-saturated, and glycolated before analysis by X-ray diffraction. Semi-quantitative percentages of smectite, illite, and kaolinite plus chlorite were calculated using peak areas and standard weighting factors. Most fine-grained sediment is supplied to the shelf by rivers during major winter storms, especially during El Nin??o years. The largest sediment fluxes to the region are from the Santa Ynez and Santa Clara Rivers, which drain the Transverse Ranges. The mean clay-mineral suite for the entire shelf sediment data set (26% smectite, 50% illite, 24% kaolinite+chlorite) is closely comparable to that for the mean of all the rivers (31% smectite, 49% illite, 20% kaolinite+chlorite), indicating that the main source of shelf fine-grained sediments is the adjacent rivers. However, regional variations do exist and the shelf is divided into four provinces with characteristic clay-mineral suites. The means of the clay-mineral suites of the two southernmost provinces are within analytical error of the mineral suites of adjacent rivers. The next province to the north includes Santa Monica Bay and has a suite of clay minerals derived from mixing of fine-grained sediments from several sources, both from the north and south. The northernmost province clay-mineral suite matches moderately well that of the adjacent rivers, but does

Parasitic helminths and their beneficial impact on type 1 and type 2 diabetes.

PubMed

Berbudi, Afiat; Ajendra, Jesuthas; Wardani, Ajeng P F; Hoerauf, Achim; Hübner, Marc P

2016-03-01

It is estimated that by the year 2035 almost 600 million people will suffer from diabetes. In the case of type 2 diabetes, the strongest increase of diabetes incidence occurs in developing and newly industrialized countries. This increase correlates not only with a progressing sedentary lifestyle and nutritional changes, but also environmental changes. Similarly, the increase of type 1 diabetes incidence in industrialized countries over the past decades cannot be explained by genetic factors alone, suggesting that environmental changes are also involved. One such environmental change is a reduced exposure to pathogens because of improved hygiene. Parasitic helminths modulate the immune system of their hosts and induce type 2 as well as regulatory immune responses. As pro-inflammatory immune responses are crucial for the onset of both type 1 and type 2 diabetes, helminth-induced immunomodulation may prevent diabetes onset and ameliorate insulin sensitivity. Several epidemiological studies in human and experimental animal models support such a protective effect of helminths for autoimmune diabetes. Recent studies further suggest that helminths may also provide such a beneficial effect for type 2 diabetes. In this review we summarize studies that investigated parasitic helminths and helminth-derived products and their impact on both type 1 and type 2 diabetes highlighting potential protective mechanisms. Copyright © 2015 John Wiley & Sons, Ltd.

Type 2 and type 3 burst theory

NASA Technical Reports Server (NTRS)

Smith, D. F.

1973-01-01

The present state of the theory of type 3 bursts is reviewed by dividing the problem into the exciting agency, radiation source, and propagation of radiation between the source and the observer. In-situ measurements indicate that the excitors are electron streams of energy about 40 keV which are continuously relaxing. An investigation of neutralization of an electron stream indicates that n sub s is much less than 100,000 n sub e, where n sub s is the stream density and n sub e the coronal electron density. In situ observations are consistent with this result. An analysis of propagation of electrons in the current sheets of coronal streamers shows that such propagation at heights greater than 1 solar radius is impossible. The mechanisms for radiation are reviewed; it is shown that fundamental radiation at high frequencies (approximately 100 MHz) is highly beamed in the radial direction and that near the earth second harmonic radiation must be dominant. Because of beaming of the fundamental at high frequencies, it can often be quite weak near the limb so that the second harmonic is dominant. In considering propagation to the observer, the results of scattering of radiation are discussed. The present state of the theory of type 2 bursts is reviewed in the same manner as type 3 bursts.

Meat-type chickens have a higher efficiency of mitochondrial oxidative phosphorylation than laying-type chickens.

PubMed

Toyomizu, Masaaki; Kikusato, Motoi; Kawabata, Yusuke; Azad, Md Abul Kalam; Inui, Eriko; Amo, Taku

2011-05-01

Meat-type chickens show high feed efficiency and have a very rapid growth rate compared with laying-type chickens. To clarify whether the type-specific difference in feed conversion efficiency is involved in mitochondrial bioenergetics, modular kinetic analysis was applied to oxidative phosphorylation in skeletal muscle mitochondria of both type chickens. Mitochondria from skeletal muscle of meat-type chickens showed greater substrate oxidation and phosphorylating activities, and less proton leak than those of the laying-type, resulting in a higher efficiency of oxidative phosphorylation. Gene expression and protein content of uncoupling protein (avUCP) but not adenine nucleotide translocase (avANT) gene expression were lower in skeletal muscle mitochondria of meat-type chickens than the laying-type. The current results regarding a higher efficiency of oxidative phosphorylation and UCP content may partially support the high feed efficiency of meat-type chickens. Copyright © 2011 Elsevier Inc. All rights reserved.

Type Ia Supernova Cosmology

NASA Astrophysics Data System (ADS)

Leibundgut, B.; Sullivan, M.

2018-03-01

The primary agent for Type Ia supernova cosmology is the uniformity of their appearance. We present the current status, achievements and uncertainties. The Hubble constant and the expansion history of the universe are key measurements provided by Type Ia supernovae. They were also instrumental in showing time dilation, which is a direct observational signature of expansion. Connections to explosion physics are made in the context of potential improvements of the quality of Type Ia supernovae as distance indicators. The coming years will see large efforts to use Type Ia supernovae to characterise dark energy.

Type 1 and type 2 cytokine dysregulation in human infectious, neoplastic, and inflammatory diseases.

PubMed Central

Lucey, D R; Clerici, M; Shearer, G M

1996-01-01

In the mid-1980s, Mosmann, Coffman, and their colleagues discovered that murine CD4+ helper T-cell clones could be distinguished by the cytokines they synthesized. The isolation of human Th1 and Th2 clones by Romagnani and coworkers in the early 1990s has led to a large number of reports on the effects of Th1 and Th2 on the human immune system. More recently, cells other than CD4+ T cells, including CD8+ T cells, monocytes, NK cells, B cells, eosinophils, mast cells, basophils, and other cells, have been shown to be capable of producing "Th1" and "Th2" cytokines. In this review, we examine the literature on human diseases, using the nomenclature of type 1 (Th1-like) and type 2 (Th2-like) cytokines, which includes all cell types producing these cytokines rather than only CD4+ T cells. Type 1 cytokines include interleukin-2 (IL-2), gamma interferon, IL-12 and tumor necrosis factor beta, while type 2 cytokines include IL-4, IL-5, IL-6, IL-10, and IL-13. In general, type 1 cytokines favor the development of a strong cellular immune response whereas type 2 cytokines favor a strong humoral immune response. Some of these type 1 and type 2 cytokines are cross-regulatory. For example, gamma interferon and IL-12 decrease the levels of type 2 cytokines whereas IL-4 and IL-10 decrease the levels of type 1 cytokines. We use this cytokine perspective to examine human diseases including infections due to viruses, bacteria, parasites, and fungi, as well as selected neoplastic, atopic, rheumatologic, autoimmune, and idiopathic-inflammatory conditions. Clinically, type 1 cytokine-predominant responses should be suspected in any delayed-type hypersensitivity-like granulomatous reactions and in infections with intracellular pathogens, whereas conditions involving hypergammaglobulinemia, increased immunoglobulin E levels, and/or eosinophilia are suggestive of type 2 cytokine-predominant conditions. If this immunologic concept is relevant to human diseases, the potential exists for

Comparison of osteoporosis in US adults with type 1 and type 2 diabetes mellitus.

PubMed

DeShields, S C; Cunningham, T D

2018-01-20

We examined bone mineral density (BMD) and osteoporosis prevalence in those with type 1 compared to type 2 diabetes derived from a nationally representative sample from the civilian community in the United States. Data from the National Health and Nutrition Examination Survey (NHANES) for 2005-2006, 2007-2008, 2009-2010, and 2013-2014 were merged to obtain a large sample of diabetics at least 20 years of age with participation in the interview and medical examination. Osteoporosis status was defined by BMD at the total femur, femoral neck, or total lumbar spine. Self-reported diabetics that were prescribed insulin within the first year of diagnosis, are currently taking insulin, and reported no prescriptions for any diabetic pills were classified as type 1. Remaining self-reported diabetics were deemed as having type 2. A total of 2050 diabetics were included in which 87 (4%) were classified as type 1. Type 1 diabetics were found to have a significantly lower BMD at the total femur and femoral neck, but not at the lumbar spine in the adjusted models. Diabetics with type 1 were 4.7 times more likely to have osteoporosis than those with type 2. There was no significant relationship between diabetes type and BMD or osteoporosis prior to adjustment for confounders. Although our results show an increased likelihood of osteoporosis among those with type 1 diabetes, future studies including a larger sample from a community population are needed. It may benefit diabetics, especially those with type 1, to initiate osteoporosis screening methods including evaluation of fracture risk, bone quality, and BMD measurements at multiple sites earlier than recommended.

Serologic assessment of type 1 and type 2 immunity in healthy Japanese adults.

PubMed

Birmann, Brenda M; Mueller, Nancy; Okayama, Akihiko; Hsieh, Chung-Cheng; Tachibana, Nobuyoshi; Tsubouchi, Hirohito; Lennette, Evelyne T; Harn, Donald; Stuver, Sherri

2004-08-01

We assessed the informativeness of several serologic biomarkers of immune function using serum specimens collected in the Miyazaki Cohort Study from subjects who were seronegative for anti-human T-cell lymphotrophic virus I and anti-hepatitis C virus. To broadly characterize type 1 immune status, we measured EBV antibody titers, because titer profiles associated with cellular immune suppression are well described. We also tested for three type 2 biomarkers: total serum IgE, soluble CD23, and soluble CD30. Nonreactivity to a tuberculin purified protein derivative (PPD) skin test is indicative of diminished delayed-type hypersensitivity (type 1) responsiveness in the study population due to a history of tuberculosis exposure or Bacillus Calmette-Guérin vaccination. We therefore evaluated the serologic markers as predictors of PPD nonreactivity using logistic regression. Subjects whose EBV antibody profiles were consistent with deficient type 1 immunity were more than thrice as likely to be PPD nonreactive as persons with "normal" antibody titers. Elevated total IgE was also strongly associated with PPD nonreactivity (odds ratio 3.4, 95% confidence interval 1.2-9.9); elevated soluble CD23 had a weaker, but positive, odds ratio, whereas soluble CD30 levels were not predictive of PPD status. Therefore, PPD nonreactivity is associated, in this population, with a pattern of serum biomarkers that is indicative of diminished type 1 and elevated type 2 immunity. We conclude that, with the exception of soluble CD30, the serologic markers are informative for the characterization of type 1/type 2 immune status using archived sera from study populations of healthy adults.

Psychological Type and Counselling.

ERIC Educational Resources Information Center

Bayne, Rowan

1995-01-01

Psychological type as a theory of four major personality characteristics is applied to empathy and choice of strategy. Discusses how versatile counselors should be and of how, specifically, type can be used in counseling. The problem of losing weight is used to illustrate how strategies may be matched with clients of different types or…

Mineralogy and diagenesis of low-permeability sandstones of Late Cretaceous age, Piceance Creek Basin, northwestern Colorado

USGS Publications Warehouse

Hansley, Paula L.; Johnson, Ronald C.

1980-01-01

This report presents preliminary results of a mineralogic and diagenetic study of some low-permeability sandstones from measured surface sections and cores obtained from drill holes in the Piceance Creek Basin of northwestern Colorado. A documentation of the mineralogy and diagenetic history will aid in the exploration for natural gas and in the development of recovery technology in these low-permability sandstones. These sandstones are in the nonmarine upper part of the Mesaverde Formation (or Group) of Late Cretaceous age and are separated from overlying lower Tertiary rocks by a major regional unconformity. Attention is focused on the sandstone units of the Ohio Creek Member, which directly underlies the unconformity; however, comparisons between the mineralogy of the Ohio Creek strata and that of the underlying sandstone units are made whenever possible. The Ohio Creek is a member of the Hunter Canyon Formation (Mesaverde Group) in the southwestern part of the basin, and the Mesaverde Formation in the southern and central parts of the basin. The detrital mineralogy is fairly constant throughout all of these nonrnarine Cretaceous sandstone units; however, in the southeastern part of the basin, there is an increase in percentage of feldspar, quartzite, and igneous rock fragments in sandstones of the Ohio Creek Member directly underlying the unconformity. In the southwestern part of the basin, sandstones of the Ohio Creek Member are very weathered and are almost-entirely comprised of quartz, chert, and kaolinite. A complex diagenetic history, partly related to the overlying unconformity, appears to be responsible for transforming these sandstones into potential gas reservoirs. The general diagenetic sequence for the entire Upper Cretaceous interval studied is interpreted to be (early to late): early(?) calcite cement, chlorite, quartz overgrowths, calcite cement, secondary porosity, analcime (surface only), kaolinite and illite, and late carbonate cements

Flash-Type Discrimination

NASA Technical Reports Server (NTRS)

Koshak, William J.

2010-01-01

This viewgraph presentation describes the significant progress made in the flash-type discrimination algorithm development. The contents include: 1) Highlights of Progress for GLM-R3 Flash-Type discrimination Algorithm Development; 2) Maximum Group Area (MGA) Data; 3) Retrieval Errors from Simulations; and 4) Preliminary Global-scale Retrieval.

Cardiovascular responses in type A and type B men to a series of stressors.

PubMed

Ward, M M; Chesney, M A; Swan, G E; Black, G W; Parker, S D; Rosenman, R H

1986-02-01

Fifty-six healthy adult males were administered the Type A Structured Interview and assessed as exhibiting either Type A (N = 42) or Type B (N = 14) behavior pattern. They were monitored for systolic (SBP) and diastolic blood pressure (DBP) and heart rate (HR) responses during a series of six challenging tasks: Mental Arithmetic, Hypothesis Testing, Reaction Time, Video Game, Handgrip, and Cold Pressor. The results indicated that Type A subjects exhibited greater cardiovascular responses than did Type B subjects during some (Hypothesis Testing, Reaction Time, Video Game and Mental Arithmetic) but not all (Handgrip and Cold Pressor) of the tasks. These results are discussed in terms of previously reported findings on conditions that do and do not produce differences in Type A/B cardiovascular stress responses.

Comparison of Two Commercial Type 1 Porcine Reproductive and Respiratory Syndrome Virus (PRRSV) Modified Live Vaccines against Heterologous Type 1 and Type 2 PRRSV Challenge in Growing Pigs.

PubMed

Kim, Taeyeon; Park, Changhoon; Choi, Kyuhyung; Jeong, Jiwoon; Kang, Ikjae; Park, Su-Jin; Chae, Chanhee

2015-06-01

The objective of the present study was to compare the efficacy of two commercial type 1 porcine reproductive and respiratory syndrome virus (PRRSV) modified live vaccines against heterologous type 1 and type 2 PRRSV challenge in growing pigs. Vaccination with a type 1 PRRSV vaccine reduced the level of viremia after type 1 PRRSV challenge but did not reduce the level of viremia after the type 2 PRRSV challenge in pigs. Increased levels of interleukin-10 (IL-10) stimulated by type 2 PRRSV coincided with the low numbers of type 2 PRRSV-specific interferon gamma-secreting cells (IFN-γ-SC) in vaccinated pigs after type 2 PRRSV challenge, whereas low levels of IL-10 stimulated by type 1 PRRSV coincided with high numbers of type 1 PRRSV-specific IFN-γ-SC in vaccinated pigs after type 1 PRRSV challenge. Additionally, vaccination with the type 1 PRRSV vaccine effectively reduced the lung lesions and type 1 PRRSV nucleic acids in type 1 PRRSV-challenged pigs but did not reduce lung lesions and type 2 PRRSV nucleic acids in type 2 PRRSV-challenged pigs. There were no significant differences between two commercial type 1 PRRSV vaccines against type 1 and type 2 PRRSV challenge based on virological results, immunological responses, and pathological outcomes. This study demonstrates that vaccinating pigs with the type 1 PRRSV vaccine provides partial protection against respiratory disease with heterologous type 1 PRRSV challenge but no protection with heterologous type 2 PRRSV challenge. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Types of Data Systems

ERIC Educational Resources Information Center

Gould, Tate; Nicholas, Amy; Ruggiero, Tony; Blandford, William; Thayer, Sara; Bull, Bruce

2015-01-01

There are several types of data systems that support data from Part C/619 programs. Although the system types have similarities, each has its own unique characteristics and purposes. The attributes that make one type of data system a particularly good fit for one data-related need or function can be less desirable for another need or function. In…

[Diagnostic values of serum type III procollagen N-terminal peptide in type IV gastric cancer].

PubMed

Akazawa, S; Fujiki, T; Kanda, Y; Kumai, R; Yoshida, S

1985-04-01

Since increased synthesis of collagen has been demonstrated in tissue of type IV gastric cancer, we attempted to distinguish type IV gastric cancer from other cancers by measuring serum levels of type III procollagen N-terminal peptide (type III-N-peptide). Mean serum levels in type IV gastric cancer patients without metastasis were found to be elevated above normal values and developed a tendency to be higher than those in types I, II and III gastric cancer patients without metastasis. Highly positive ratios were found in patients with liver diseases including hepatoma and colon cancer, biliary tract cancer, and esophageal cancer patients with liver, lung or bone metastasis, but only 2 out of 14 of these cancer patients without such metastasis showed positive serum levels of type III-N-peptide. Positive cases in patients with type IV gastric cancer were obtained not only in the group with clinical stage IV but also in the groups with clinical stages II and III. In addition, high serum levels of type III-N-peptide in patients with type IV gastric cancer were seen not only in the cases with liver, lung or bone metastasis but also in cases with disseminated peritoneal metastasis alone. These results suggest that if the serum level of type III-N-peptide is elevated above normal values, type IV gastric cancer should be suspected after ruling out liver diseases, myelofibrosis and liver, lung or bone metastasis.

Global distribution of minerals in arid soils as lower boundary condition in dust models

NASA Astrophysics Data System (ADS)

Nickovic, Slobodan

2010-05-01

Mineral dust eroded from arid soils affects the radiation budget of the Earth system, modifies ocean bioproductivity and influences human health. Dust aerosol is a complex mixture of minerals. Dust mineral composition has several potentially important impacts to environment and society. Iron and phosphorus embedded in mineral aerosol are essential for the primary marine productivity when dust deposits over the open ocean. Dust also acts as efficient agent for heterogeneous ice nucleation and this process is dependent on mineralogical structure of dust. Recent findings in medical geology indicate possible role of minerals to human health. In this study, a new 1-km global database was developed for several minerals (Illite, Kaolinite, Smectite, Calcite, Quartz, Feldspar, Hematite and Gypsum) embedded in clay and silt populations of arid soils. For the database generation, high-resolution data sets on soil textures, soil types and land cover was used. Tin addition to the selected minerals, phosphorus was also added whose geographical distribution was specified from compiled literature and data on soil types. The developed global database was used to specify sources of mineral fractions in the DREAM dust model and to simulate atmospheric paths of minerals and their potential impacts on marine biochemistry and tropospheric ice nucleation.