Dosimetric properties of radiophotoluminescent glass detector in low-energy photon beams.

PubMed

Kadoya, Noriyuki; Shimomura, Kouhei; Kitou, Satoshi; Shiota, Yasuo; Fujita, Yukio; Dobashi, Suguru; Takeda, Ken; Jingu, Keiichi; Matsushita, Haruo; Namito, Yoshihito; Ban, Syuichi; Koyama, Syuji; Tabushi, Katsuyoshi

2012-10-01

A radiophotoluminescent glass rod dosimeter (RGD) has recently become commercially available. It is being increasingly used for dosimetry in radiotherapy to measure the absorbed dose including scattered low-energy photons on the body surface of a patient and for postal dosimetry audit. In this article, the dosimetric properties of the RGD, including energy dependence of the dose response, reproducibly, variation in data obtained by the RGD for each energy, and angular dependence in low-energy photons, are discussed. An RGD (GD-301, Asahi Techno Glass Corporation, Shizuoka, Japan) was irradiated with monochromatic low-energy photon beams generated by synchrotron radiation at Photon Factory, High Energy Accelerator Research Organization (KEK). The size of GD-301 was 1.5 mm in diameter and 8.5 mm in length and the active dose readout volume being 1 mm diameter and 0.6 mm depth located 0.7 mm from the end of the detector. The energy dependence of the dose response and reproducibility and variation were investigated for RGDs irradiated with a plastic holder and those irradiated without the plastic holder. Response of the RGD was obtained by not only conventional single field irradiation but also bilateral irradiation. Angular dependence of the RGD was measured in the range of 0°-90° for 13, 17, 40, and 80 keV photon beams by conventional single field irradiation. The dose responses had a peak at around 40 keV. For the energy range of less than 25 keV, all dose response curves steeply decreased in comparison with the ratio of mass energy absorption coefficient of the RGD to that of air. As for the reproducibility and variation in data obtained by the RGD, the coefficient of variance increased with decrease in photon energy. Furthermore, the variation for bilateral irradiation was less than that for single field irradiation. Regarding angular dependence of the RGD, for energies of 13 and 17 keV, the response decreased with increase in the irradiation angle, and the

AR-NE3A, a New Macromolecular Crystallography Beamline for Pharmaceutical Applications at the Photon Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, Yusuke; Hiraki, Masahiko; Sasajima, Kumiko

2010-06-23

Recent advances in high-throughput techniques for macromolecular crystallography have highlighted the importance of structure-based drug design (SBDD), and the demand for synchrotron use by pharmaceutical researchers has increased. Thus, in collaboration with Astellas Pharma Inc., we have constructed a new high-throughput macromolecular crystallography beamline, AR-NE3A, which is dedicated to SBDD. At AR-NE3A, a photon flux up to three times higher than those at existing high-throughput beams at the Photon Factory, AR-NW12A and BL-5A, can be realized at the same sample positions. Installed in the experimental hutch are a high-precision diffractometer, fast-readout, high-gain CCD detector, and sample exchange robot capable ofmore » handling more than two hundred cryo-cooled samples stored in a Dewar. To facilitate high-throughput data collection required for pharmaceutical research, fully automated data collection and processing systems have been developed. Thus, sample exchange, centering, data collection, and data processing are automatically carried out based on the user's pre-defined schedule. Although Astellas Pharma Inc. has a priority access to AR-NE3A, the remaining beam time is allocated to general academic and other industrial users.« less

Investigation of in-house superconducting radio-frequency 9-cell cavity made of large grain niobium at KEK

NASA Astrophysics Data System (ADS)

Dohmae, Takeshi; Umemori, Kensei; Yamanaka, Masashi; Watanabe, Yuichi; Inoue, Hitoshi

2017-12-01

The first in-house, 9-cell, superconducting radio-frequency cavity made of large grain Nb was fabricated at KEK. Some characteristic techniques were employed for the fabrication that were not used for fine grain (FG) Nb. Even though a penetrated hole was created during electron beam welding, it was successfully repaired and did not affect the cavity performance. The completed cavity then underwent vertical tests (VTs) via several surface treatment processes. A defect that caused quenches was found after a VT at 25 mm from the equator where the typical local grinding machine developed at KEK could not be utilized. A new local grinding machine using a 3D printer was thus developed for the first time, and it completely removed this defect. Finally, the cavity achieved a maximum Q0 value of 3.8 ×1010 and accelerating gradient of 38 MV/m. The obtained Q0 value is about 1.5 times higher than that for the KEK in-house FG cavity.

A trial of production of the plant-derived high-value protein in a plant factory: photosynthetic photon fluxes affect the accumulation of recombinant miraculin in transgenic tomato fruits.

PubMed

Kato, Kazuhisa; Maruyama, Shinichiro; Hirai, Tadayoshi; Hiwasa-Tanase, Kyoko; Mizoguchi, Tsuyoshi; Goto, Eiji; Ezura, Hiroshi

2011-08-01

One of the ultimate goals of plant science is to test a hypothesis obtained by basic science and to apply it to agriculture and industry. A plant factory is one of the ideal systems for this trial. Environmental factors affect both plant yield and the accumulation of recombinant proteins for industrial applications within transgenic plants. However, there have been few reports studying plant productivity for recombinant protein in closed cultivation systems called plant factories. To investigate the effects of photosynthetic photon flux (PPF) on tomato fruit yield and the accumulation of recombinant miraculin, a taste-modifying glycoprotein, in transgenic tomato fruits, plants were cultivated at various PPFs from 100 to 400 (µmol m(-2) s(-)1) in a plant factory. Miraculin production per unit of energy used was highest at PPF100, although miraculin production per unit area was highest at PPF300. The commercial productivity of recombinant miraculin in transgenic tomato fruits largely depended on light conditions in the plant factory. Our trial will be useful to consider the trade-offs between the profits from production of high-value materials in plants and the costs of electricity.

T0 chopper developed at KEK

NASA Astrophysics Data System (ADS)

Itoh, Shinichi; Ueno, Kenji; Ohkubo, Ryuji; Sagehashi, Hidenori; Funahashi, Yoshisato; Yokoo, Tetsuya

2012-01-01

We developed a T0 chopper rotating at 100 Hz at the High Energy Accelerator Research Organization (KEK) for the reduction of background noise in neutron scattering experiments at the Japan Proton Accelerator Research Complex (J-PARC). The T0 chopper consists of a rotor of 120 kg made from Inconel X750, supported by mechanical bearings in vacuum. The motor is located outside the vacuum and the rotation is transmitted into vacuum through magnetic seals. The motor should rotate in synchronization with the production timing of pulsed neutrons. The rotational fluctuations and running time were in good agreement with the specifications, i.e., phase control accuracy of less than 5 μs and running time of more than 4000 h without changing any component. A semi-auto installation mechanism was developed for installing under the shielding and for maintenance purposes. Based on the result of the development, actual machines were made for the neutron beamlines at J-PARC. We successfully reduced the background noise to 1/30 at neutron energies near 500 meV.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bevan, A. J.; Golob, B.; Mannel, Th.

This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C.

Thermal photons in heavy ion collisions at 158 A GeV

NASA Astrophysics Data System (ADS)

Dutt, Sunil

2018-05-01

The essence of experimental ultra-relativistic heavy ion collision physics is the production and study of strongly interacting matter at extreme energy densities, temperatures and consequent search for equation of state of nuclear matter. The focus of the analysis has been to examine pseudo-rapidity distributions obtained for the γ-like particles in pre-shower photon multiplicity detector. This allows the extension of scaled factorial moment analysis to bin sizes smaller than those accessible to other experimental techniques. Scaled factorial moments are calculated using horizontal corrected and vertical analysis. The results are compared with simulation analysis using VENUS event generator.

Evaluation of beam halo from beam-gas scattering at the KEK Accelerator Test Facility

NASA Astrophysics Data System (ADS)

Yang, R.; Naito, T.; Bai, S.; Aryshev, A.; Kubo, K.; Okugi, T.; Terunuma, N.; Zhou, D.; Faus-Golfe, A.; Kubytskyi, V.; Liu, S.; Wallon, S.; Bambade, P.

2018-05-01

In circular colliders, as well as in damping rings and synchrotron radiation light sources, beam halo is one of the critical issues limiting the performance as well as potentially causing component damage and activation. It is imperative to clearly understand the mechanisms that lead to halo formation and to test the available theoretical models. Elastic beam-gas scattering can drive particles to large oscillation amplitudes and be a potential source of beam halo. In this paper, numerical estimation and Monte Carlo simulations of this process at the ATF of KEK are presented. Experimental measurements of beam halo in the ATF2 beam line using a diamond sensor detector are also described, which clearly demonstrate the influence of the beam-gas scattering process on the transverse halo distribution.

Recent results from TRISTAN at KEK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzuki, Shiro

1994-12-01

Recent results of the TRISTAN experiment with high luminosity runs are reviewed. Updated results on lepton and quark pair production in the annihilation processes are presented, and limits on the compositeness scale and lower mass limit for extra Z bosons are given. The total hadronic cross section is presented in the effective Born approximation. A search for a resonance suggested by the L3 group is done in several different final states. The strong coupling constant {alpha}{sub s} is derived from several observables with an improved theoretical framework. The running nature of {alpha}{sub s} is studied in comparison with PEP4 andmore » ALEPH data. Various properties of quark and gluon jets are examined. Hard scattering of two photons is established and these data provide information on quark and gluon distributions in the photon.« less

Sequence Factorial and Its Applications

ERIC Educational Resources Information Center

Asiru, Muniru A.

2012-01-01

In this note, we introduce sequence factorial and use this to study generalized M-bonomial coefficients. For the sequence of natural numbers, the twin concepts of sequence factorial and generalized M-bonomial coefficients, respectively, extend the corresponding concepts of factorial of an integer and binomial coefficients. Some latent properties…

Plant Factory

NASA Astrophysics Data System (ADS)

Ikeda, Hideo

Recently, much attention is paid on the plant factory, as it enable to grow plants stably under extraordinary climate condition such as high and/or low air temperature and less rain. Lots of questions such as decreasing investing cost, realizing stable plant production and developing new growing technique should be solved for making popular this growing system. However, I think that we can introduce a highly developed Japanese industrial now-how to plant factory system and can produce a business chance to the world market.

Neutrino factory

DOE PAGES

Bogomilov, M.; Matev, R.; Tsenov, R.; ...

2014-12-08

The properties of the neutrino provide a unique window on physics beyond that described by the standard model. The study of subleading effects in neutrino oscillations, and the race to discover CP-invariance violation in the lepton sector, has begun with the recent discovery that theta(13) > 0. The measured value of theta(13) is large, emphasizing the need for a facility at which the systematic uncertainties can be reduced to the percent level. The neutrino factory, in which intense neutrino beams are produced from the decay of muons, has been shown to outperform all realistic alternatives and to be capable ofmore » making measurements of the requisite precision. Its unique discovery potential arises from the fact that only at the neutrino factory is it practical to produce high-energy electron (anti) neutrino beams of the required intensity. This paper presents the conceptual design of the neutrino factory accelerator facility developed by the European Commission Framework Programme 7 EURO nu. Design Study consortium. EURO nu coordinated the European contributions to the International Design Study for the Neutrino Factory (the IDS-NF) collaboration. The EURO nu baseline accelerator facility will provide 10(21) muon decays per year from 12.6 GeV stored muon beams serving a single neutrino detector situated at a source-detector distance of between 1 500 km and 2 500 km. A suite of near detectors will allow definitive neutrino-scattering experiments to be performed.« less

Research progress at the Slow Positron Facility in the Institute of Materials Structure Science, KEK

NASA Astrophysics Data System (ADS)

Hyodo, T.; Wada, K.; Mochizuki, I.; Kimura, M.; Toge, N.; Shidara, T.; Fukaya, Y.; Maekawa, M.; Kawasuso, A.; Iida, S.; Michishio, K.; Nagashima, Y.

2017-01-01

Recent results at the Slow Positron Facility (SPF), Institute of Materials Structure Science (IMSS), KEK are reported. Studies using the total-reflection high-energy positron diffraction (TRHEPD) station revealed the structures of rutile-TiO2(110) (1×2), graphene on Cu (111) and Co (0001), and germanene on Al (111). First observations of the shape resonance in the Ps- photodetachment process were made using the positronium negative ion (Ps-) station. Experiments using the positronium time-of-flight (Ps-TOF) station showed significant enhancement of the Ps formation efficiency and the energy loss in the Ps formation-emission process. A pulse-stretching section has been implemented, which stretches the positron pulse width from 1.2 μs up to almost 20 ms.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aoki, Sadao; Namikawa, Tadahiro; Hoshino, Masato

A Zernike-type phase contrast hard X-ray microscope was constructed at the Photon Factory BL3C2 (KEK). A white beam from a bending magnet was monochromatized by a silicon double crystal monochromator. Monochromatic parallel X-ray beam illuminated a sample, and transmitted and diffracted X-ray beams were imaged by a Fresnel zone plate (FZP) which had the outer zone width of 100 nm. A phase plate made of a thin aluminum foil with a pinhole was set at the back focal plane of the FZP. The phase plate modulated the diffraction beam from the FZP, whereas a direct beam passed through the pinhole.more » The resolution of the microscope was measured by observing a tantalum test pattern at an X-ray energy of 9 keV. A 100nm line-and-space pattern could be resolved. X-ray montage pictures of growing eggs of artemia (plankton) were obtained.« less

In-Factory Learning - Qualification For The Factory Of The Future

NASA Astrophysics Data System (ADS)

Quint, Fabian; Mura, Katharina; Gorecky, Dominic

2015-07-01

The Industry 4.0 vision anticipates that internet technologies will find their way into future factories replacing traditional components by dynamic and intelligent cyber-physical systems (CPS) that combine the physical objects with their digital representation. Reducing the gap between the real and digital world makes the factory environment more flexible, more adaptive, but also more complex for the human workers. Future workers require interdisciplinary competencies from engineering, information technology, and computer science in order to understand and manage the diverse interrelations between physical objects and their digital counterpart. This paper proposes a mixed-reality based learning environment, which combines physical objects and visualisation of digital content via Augmented Reality. It uses reality-based interaction in order to make the dynamic interrelations between real and digital factory visible and tangible. We argue that our learning system does not work as a stand-alone solution, but should fit into existing academic and advanced training curricula.

Midlands Teaching Factory, LTD.

ERIC Educational Resources Information Center

Midlands Technical Coll., Columbia, SC.

In 1987, Midlands Technical College (MTC), in Columbia, South Carolina, initiated a Computer Integrated Manufacturing (CIM) project, the Midlands Teaching Factory, LTD, which integrated various college departments with the goal of manufacturing a high quality, saleable product. The faculty developed a teaching factory model which was designed to…

Sequence Factorial of "g"-Gonal Numbers

ERIC Educational Resources Information Center

Asiru, Muniru A.

2013-01-01

The gamma function, which has the property to interpolate the factorial whenever the argument is an integer, is a special case (the case "g"?=?2) of the general term of the sequence factorial of "g"-gonal numbers. In relation to this special case, a formula for calculating the general term of the sequence factorial of any…

Photon-number statistics in resonance fluorescence

NASA Astrophysics Data System (ADS)

Lenstra, D.

1982-12-01

The theory of photon-number statistics in resonance fluorescence is treated, starting with the general formula for the emission probability of n photons during a given time interval T. The results fully confirm formerly obtained results by Cook that were based on the theory of atomic motion in a traveling wave. General expressions for the factorial moments are derived and explicit results for the mean and the variance are given. It is explicitly shown that the distribution function tends to a Gaussian when T becomes much larger than the natural lifetime of the excited atom. The speed of convergence towards the Gaussian is found to be typically slow, that is, the third normalized central moment (or the skewness) is proportional to T-12. However, numerical results illustrate that the overall features of the distribution function are already well represented by a Gaussian when T is larger than a few natural lifetimes only, at least if the intensity of the exciting field is not too small and its detuning is not too large.

New generation electron-positron factories

NASA Astrophysics Data System (ADS)

Zobov, Mikhail

2011-09-01

In 2010 we celebrate 50 years since commissioning of the first particle storage ring ADA in Frascati (Italy) that also became the first electron-positron collider in 1964. After that date the particle colliders have increased their intensity, luminosity and energy by several orders of magnitude. Namely, because of the high stored beam currents and high rate of useful physics events (luminosity) the modern electron-positron colliders are called "factories". However, the fundamental physics has required luminosities by 1-2 orders of magnitudes higher with respect to those presently achieved. This task can be accomplished by designing a new generation of factories exploiting the potential of a new collision scheme based on the Crab Waist (CW) collision concept recently proposed and successfully tested at Frascati. In this paper we discuss the performance and limitations of the present generation electron-positron factories and give a brief overview of new ideas and collision schemes proposed for further collider luminosity increase. In more detail we describe the CW collision concept and the results of the crab waist collision tests in DAϕNE, the Italian ϕ-factory. Finally, we briefly describe most advanced projects of the next generation factories based on the CW concept: SuperB in Italy, SuperKEKB in Japan and SuperC-Tau in Russia.

National photonics skills standards for technicians

NASA Astrophysics Data System (ADS)

Hull, Darrell M.

1995-10-01

Photonics is defined as the generation, manipulation, transport, detection, and use of light information and energy whose quantum unit is the photon. The range of applications of phonics extends from energy generation to detection to communication and information processing. Photonics is at the heart of today's communication systems, from the laser that generates the digital information transported along a fiber- optic cable to the detector that decodes the information. Whether the transmitted information is a phone call from across the street or across the globe, photonics brings it to you. Where your health is concerned, photonics allows physicians to do minimally invasive surgery using fiber-optic endoscopes and lasers. Researches using spectroscopy and microscopy are pushing the frontiers of biotechnology in activities as widespread as diagnosing disease and probing the mysteries of the genetic code. Advanced sensing and imaging techniques monitor the environment, gathering data on crops and forests, analyzing the ocean's currents and contents, and probing the atmosphere of pollutants. Transportation needs are being impacted by photonic sensors and laser rangefinders that will soon monitor and control the traffic on our nation's highways. In our factories, photonics provides machine vision systems that give a level of quality control human inspectors could never achieve. In manufacturing, lasers are replacing a variety of cutting, welding, and marking techniques, while imaging systems teamed with neural networks are producing intelligent robots. In short, photonics is paving our way into the new millennium. The skill standard is intended to define the knowledge and capabilities - the skills - that workers in the phonics industry need. Phonics will be one of the primary battlefields of the world economic conflict, and it is imperative that U.S. photonics technicians be skilled enough to allow the United States to remain competitive in a global marketplace. The

Baby factories taint surrogacy in Nigeria.

PubMed

Makinde, Olusesan Ayodeji; Makinde, Olufunmbi Olukemi; Olaleye, Olalekan; Brown, Brandon; Odimegwu, Clifford O

2016-01-01

The practice of reproductive medicine in Nigeria is facing new challenges with the proliferation of 'baby factories'. Baby factories are buildings, hospitals or orphanages that have been converted into places for young girls and women to give birth to children for sale on the black market, often to infertile couples, or into trafficking rings. This practice illegally provides outcomes (children) similar to surrogacy. While surrogacy has not been well accepted in this environment, the proliferation of baby factories further threatens its acceptance. The involvement of medical and allied health workers in the operation of baby factories raises ethical concerns. The lack of a properly defined legal framework and code of practice for surrogacy makes it difficult to prosecute baby factory owners, especially when they are health workers claiming to be providing services to clients. In this environment, surrogacy and other assisted reproductive techniques urgently require regulation in order to define when ethico-legal lines have been crossed in providing surrogacy or surrogacy-like services. Copyright © 2015 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Slime Factory.

ERIC Educational Resources Information Center

Fowler, Marilyn L.

1992-01-01

Describes a classroom activity using slime, a colloid: it behaves like both a solid and liquid. Explains how slime can be produced from guar gum. An activity where students work in teams and become a slime factory is presented. (PR)

Search for Invisible Decays of a Dark Photon Produced in e^{+}e^{-} Collisions at BaBar.

PubMed

Lees, J P; Poireau, V; Tisserand, V; Grauges, E; Palano, A; Eigen, G; Brown, D N; Derdzinski, M; Giuffrida, A; Kolomensky, Yu G; Fritsch, M; Koch, H; Schroeder, T; Hearty, C; Mattison, T S; McKenna, J A; So, R Y; Blinov, V E; Buzykaev, A R; Druzhinin, V P; Golubev, V B; Kravchenko, E A; Onuchin, A P; Serednyakov, S I; Skovpen, Yu I; Solodov, E P; Todyshev, K Yu; Lankford, A J; Gary, J W; Long, O; Eisner, A M; Lockman, W S; Panduro Vazquez, W; Chao, D S; Cheng, C H; Echenard, B; Flood, K T; Hitlin, D G; Kim, J; Miyashita, T S; Ongmongkolkul, P; Porter, F C; Röhrken, M; Huard, Z; Meadows, B T; Pushpawela, B G; Sokoloff, M D; Sun, L; Smith, J G; Wagner, S R; Bernard, D; Verderi, M; Bettoni, D; Bozzi, C; Calabrese, R; Cibinetto, G; Fioravanti, E; Garzia, I; Luppi, E; Santoro, V; Calcaterra, A; de Sangro, R; Finocchiaro, G; Martellotti, S; Patteri, P; Peruzzi, I M; Piccolo, M; Rotondo, M; Zallo, A; Passaggio, S; Patrignani, C; Lacker, H M; Bhuyan, B; Mallik, U; Chen, C; Cochran, J; Prell, S; Ahmed, H; Gritsan, A V; Arnaud, N; Davier, M; Le Diberder, F; Lutz, A M; Wormser, G; Lange, D J; Wright, D M; Coleman, J P; Gabathuler, E; Hutchcroft, D E; Payne, D J; Touramanis, C; Bevan, A J; Di Lodovico, F; Sacco, R; Cowan, G; Banerjee, Sw; Brown, D N; Davis, C L; Denig, A G; Gradl, W; Griessinger, K; Hafner, A; Schubert, K R; Barlow, R J; Lafferty, G D; Cenci, R; Jawahery, A; Roberts, D A; Cowan, R; Robertson, S H; Dey, B; Neri, N; Palombo, F; Cheaib, R; Cremaldi, L; Godang, R; Summers, D J; Taras, P; De Nardo, G; Sciacca, C; Raven, G; Jessop, C P; LoSecco, J M; Honscheid, K; Kass, R; Gaz, A; Margoni, M; Posocco, M; Simi, G; Simonetto, F; Stroili, R; Akar, S; Ben-Haim, E; Bomben, M; Bonneaud, G R; Calderini, G; Chauveau, J; Marchiori, G; Ocariz, J; Biasini, M; Manoni, E; Rossi, A; Batignani, G; Bettarini, S; Carpinelli, M; Casarosa, G; Chrzaszcz, M; Forti, F; Giorgi, M A; Lusiani, A; Oberhof, B; Paoloni, E; Rama, M; Rizzo, G; Walsh, J J; Smith, A J S; Anulli, F; Faccini, R; Ferrarotto, F; Ferroni, F; Pilloni, A; Piredda, G; Bünger, C; Dittrich, S; Grünberg, O; Heß, M; Leddig, T; Voß, C; Waldi, R; Adye, T; Wilson, F F; Emery, S; Vasseur, G; Aston, D; Cartaro, C; Convery, M R; Dorfan, J; Dunwoodie, W; Ebert, M; Field, R C; Fulsom, B G; Graham, M T; Hast, C; Innes, W R; Kim, P; Leith, D W G S; Luitz, S; MacFarlane, D B; Muller, D R; Neal, H; Ratcliff, B N; Roodman, A; Sullivan, M K; Va'vra, J; Wisniewski, W J; Purohit, M V; Wilson, J R; Randle-Conde, A; Sekula, S J; Bellis, M; Burchat, P R; Puccio, E M T; Alam, M S; Ernst, J A; Gorodeisky, R; Guttman, N; Peimer, D R; Soffer, A; Spanier, S M; Ritchie, J L; Schwitters, R F; Izen, J M; Lou, X C; Bianchi, F; De Mori, F; Filippi, A; Gamba, D; Lanceri, L; Vitale, L; Martinez-Vidal, F; Oyanguren, A; Albert, J; Beaulieu, A; Bernlochner, F U; King, G J; Kowalewski, R; Lueck, T; Nugent, I M; Roney, J M; Sobie, R J; Tasneem, N; Gershon, T J; Harrison, P F; Latham, T E; Prepost, R; Wu, S L

2017-09-29

We search for single-photon events in 53  fb^{-1} of e^{+}e^{-} collision data collected with the BABAR detector at the PEP-II B-Factory. We look for events with a single high-energy photon and a large missing momentum and energy, consistent with production of a spin-1 particle A^{'} through the process e^{+}e^{-}→γA^{'}; A^{'}→invisible. Such particles, referred to as "dark photons," are motivated by theories applying a U(1) gauge symmetry to dark matter. We find no evidence for such processes and set 90% confidence level upper limits on the coupling strength of A^{'} to e^{+}e^{-} in the mass range m_{A^{'}}≤8  GeV. In particular, our limits exclude the values of the A^{'} coupling suggested by the dark-photon interpretation of the muon (g-2)_{μ} anomaly, as well as a broad range of parameters for the dark-sector models.

Supernova Dust Factory in M74

NASA Image and Video Library

2006-06-09

Astronomers using NASA Spitzer Space Telescope have spotted a dust factory 30 million light-years away in the spiral galaxy M74. The factory is located at the scene of a massive star explosive death, or supernova.

Factorials of real negative and imaginary numbers - A new perspective.

PubMed

Thukral, Ashwani K

2014-01-01

Presently, factorials of real negative numbers and imaginary numbers, except for zero and negative integers are interpolated using the Euler's gamma function. In the present paper, the concept of factorials has been generalised as applicable to real and imaginary numbers, and multifactorials. New functions based on Euler's factorial function have been proposed for the factorials of real negative and imaginary numbers. As per the present concept, the factorials of real negative numbers, are complex numbers. The factorials of real negative integers have their imaginary part equal to zero, thus are real numbers. Similarly, the factorials of imaginary numbers are complex numbers. The moduli of the complex factorials of real negative numbers, and imaginary numbers are equal to their respective real positive number factorials. Fractional factorials and multifactorials have been defined in a new perspective. The proposed concept has also been extended to Euler's gamma function for real negative numbers and imaginary numbers, and beta function.

Crystallization and X-ray diffraction analysis of the RNA primer/promoter-binding domain of influenza A virus RNA-dependent RNA polymerase PB2

PubMed Central

Kuzuhara, Takashi; Kise, Daisuke; Yoshida, Hiroko; Horita, Takahiro; Murazaki, Yoshimi; Utsunomiya, Hiroko; Tsuge, Hideaki

2009-01-01

The C-terminal domain protein (amino-acid residues 535–759) of the PB2 subunit of the RNA-dependent RNA polymerase from the highly pathogenic influenza A virus was expressed as a soluble protein in Escherichia coli and crystallized using sodium formate as a precipitant. Data sets were collected from crystals of native and selenomethionine-substituted protein on the KEK NW12 beamline at the Photon Factory and the crystals diffracted to a maximum resolution of 2.44 Å for the SeMet-derivative crystal. The native crystals were found to belong to space group P3221, with unit-cell parameters a = b = 52.5, c = 156.3 Å. The Matthews value (V M) was 2.7 Å3 Da−1, assuming the presence of one molecule in the asymmetric unit. The SeMet-derivative crystals were found to belong to the same space group, with unit-cell parameters a = b = 52.6, c = 156.4 Å. Attempts are being made to solve the structure by multi-wavelength anomalous dispersion phasing. PMID:19194006

The Role of Spatial Analysis in Detecting the Consequence of the Factory Sites : Case Study of Assalaya Factory-Sudan

NASA Astrophysics Data System (ADS)

Khair, Amar Sharaf Eldin; Purwanto; RyaSunoko, Henna; Abdullah, Omer Adam

2018-02-01

Spatial analysis is considered as one of the most important science for identifying the most appropriate site for industrialization and also to alleviate the environmental ramifications caused by factories. This study aims at analyzing the Assalaya sugarcane factory site by the use of spatial analysis to determine whether it has ramification on the White Nile River. The methodology employed for this study is Global Position System (GPS) to identify the coordinate system of the study phenomena and other relative factors. The study will also make use Geographical Information System (GIS) to implement the spatial analysis. Satellite data (LandsatDem-Digital Elevation Model) will be considered for the study area and factory in identifying the consequences by analyzing the location of the factory through several features such as hydrological, contour line and geological analysis. Data analysis reveals that the factory site is inappropriate and according to observation on the ground it has consequences on the White Nile River. Based on the finding, the study recommended some suggestions to avoid the aftermath of any factory in general. We have to take advantage of this new technological method to aid in selecting most apt locations for industries that will create an ambient environment.

Quantum computation with realistic magic-state factories

NASA Astrophysics Data System (ADS)

O'Gorman, Joe; Campbell, Earl T.

2017-03-01

Leading approaches to fault-tolerant quantum computation dedicate a significant portion of the hardware to computational factories that churn out high-fidelity ancillas called magic states. Consequently, efficient and realistic factory design is of paramount importance. Here we present the most detailed resource assessment to date of magic-state factories within a surface code quantum computer, along the way introducing a number of techniques. We show that the block codes of Bravyi and Haah [Phys. Rev. A 86, 052329 (2012), 10.1103/PhysRevA.86.052329] have been systematically undervalued; we track correlated errors both numerically and analytically, providing fidelity estimates without appeal to the union bound. We also introduce a subsystem code realization of these protocols with constant time and low ancilla cost. Additionally, we confirm that magic-state factories have space-time costs that scale as a constant factor of surface code costs. We find that the magic-state factory required for postclassical factoring can be as small as 6.3 million data qubits, ignoring ancilla qubits, assuming 10-4 error gates and the availability of long-range interactions.

Generalized Factorial Moments

NASA Astrophysics Data System (ADS)

Bialas, A.

2004-02-01

It is shown that the method of eliminating the statistical fluctuations from event-by-event analysis proposed recently by Fu and Liu can be rewritten in a compact form involving the generalized factorial moments.

The International Design Study for the Neutrino Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Long, K.

2008-02-21

The International Design Study for a future Neutrino Factory and super-beam facility (the ISS) established the physics case for a high-precision programme of long-baseline neutrino-oscillation measurements. The ISS also identified baseline specifications for the Neutrino Factory accelerator complex and the neutrino detector systems. This paper summarises the objectives of the International Design Study for the Neutrino Factory (the IDS-NF). The IDS-NF will build on the work of the ISS to deliver a Reference Design Report for the Neutrino Factory by 2012/13 and an Interim Design Report by 2010/11.

A reference architecture for the component factory

NASA Technical Reports Server (NTRS)

Basili, Victor R.; Caldiera, Gianluigi; Cantone, Giovanni

1992-01-01

Software reuse can be achieved through an organization that focuses on utilization of life cycle products from previous developments. The component factory is both an example of the more general concepts of experience and domain factory and an organizational unit worth being considered independently. The critical features of such an organization are flexibility and continuous improvement. In order to achieve these features we can represent the architecture of the factory at different levels of abstraction and define a reference architecture from which specific architectures can be derived by instantiation. A reference architecture is an implementation and organization independent representation of the component factory and its environment. The paper outlines this reference architecture, discusses the instantiation process, and presents some examples of specific architectures by comparing them in the framework of the reference model.

Acoustic scale modelling of factories, part II: 1-50 Cale model investigations of factory sound fields

NASA Astrophysics Data System (ADS)

Hodgson, M. R.; Orlowski, R. J.

1987-03-01

In this second part of a report on factory scale modelling use of a 1:50 scale variable model as a research tool is described. Details of the model are presented. The results of measurements of reverberation time and sound propagation, made in various model configurations, are used to investigate the main factors influencing factory sound fields, and the applicability of the Sabine theory to factories. The parameters investigated are the enclosure geometry (aspect ratio, volume and roof pitch), surface absorption and fittings (density, size, surface area, vertical distribution and specific types). Despite certain limitations and uncertainties resulting, for example, from surprising results associated with surface absorption, models are shown to be effective research tools. The inapplicability of the Sabine theory is confirmed and elucidated.

Slow positron applications at slow positron facility of institute of materials structure science, KEK

NASA Astrophysics Data System (ADS)

Hyodo, Toshio; Mochizuki, Izumi; Wada, Ken; Toge, Nobukazu; Shidara, Tetsuo

2018-05-01

Slow Positron Facility at High Energy Accelerator Research Organization (KEK) is a user dedicated facility with an energy-tunable (0.1 - 35 keV) slow positron beam created by a dedicated ˜ 50 MeV linac. It operates in a short pulse (width 1-12 ns, variable, 5×106 e+/s) and a long pulse (width 1.2 µs, 5×107 e+/s) modes of 50 Hz. High energy positrons from pair creation are moderated by reemission after thermalization in W foils. The reemitted positrons are then electrostatically accelerated to a desired energy up to 35 keV and magnetically transported. A pulse-stretching section (pulse stretcher) is installed in the middle of the beamline. It stretches the slow positron pulse for the experiments where too many positrons annihilating in the sample at the same time has to be avoided. Four experiment stations for TRHEPD (total-reflection high-energy positron diffraction), LEPD (low-energy positron diffraction), Ps- (positronium negative ion), and Ps-TOF (positronium time-of-flight) experiments are connected to the beamline branches, SPF-A3, SPF-A4, SPF-B1 and SPF-B2, respectively. Recent results of these stations are briefly described.

Factory daughters, the family, and nuptiality in Java.

PubMed

Wolf, D L

1990-01-01

The commercialization of agriculture, increasing landlessness, and an expanding labor class in rural areas of Java are all the result of industrialization. This work discusses the effect of female employment on marriage patterns of women working in rural factories. The central point is that employment has not only increased the financial autonomy of these women, but also increased the level of control they have over the choice of marriage partners. The data set used for analysis consisted of the observations of all factory workers and all non-factory females age 15-24 located in an agricultural village. The observations were make over a 15 month period between 1981-83. A follow up visit was made in 1986 and the following conclusions were then made: 1) the village study gave detailed data, but the data set was not large enough, thus a follow up study that encompasses more people is called for; 2) young rural female factory workers are more likely to chose their marriage partners than those engaged in traditional village labor. Of those that married and worked in factories, their fertility rate was significantly lower, compared to non-factory workers. Factory workers also had different family structures, because they spent less time living in extended families because of a larger income for the couple. This study indicates that increased economic control results in increased life decision control. This changed the daughter's economic relationship with her family and gives her more control in marriage decisions.

New halo formation mechanism at the KEK compact energy recovery linac

NASA Astrophysics Data System (ADS)

Tanaka, Olga; Nakamura, Norio; Shimada, Miho; Miyajima, Tsukasa; Ueda, Akira; Obina, Takashi; Takai, Ryota

2018-02-01

The beam halo mitigation is a very important challenge for reliable and safe operation of a high-energy machine. A systematic beam halo study was conducted at the KEK compact energy recovery linac (cERL) since non-negligible beam loss was observed in the recirculation loop during a common operation. We found that the beam loss can be avoided by making use of the collimation system. Beam halo measurements have demonstrated the presence of vertical beam halos at multiple locations in the beam line (except the region near the electron gun). Based on these observations, we made a conjecture that the transverse beam halo is attributed to the longitudinal bunch tail arising at the photocathode. The transfer of particles from the longitudinal space to a transverse halo may have been observed and studied in other machines, considering nonlinear effects as their causes. However, our study demonstrates a new unique halo formation mechanism, in which a transverse beam halo can be generated by a longitudinal bunch tail due to transverse rf kicks from the accelerating (monopole) fields of the radio-frequency cavities. This halo formation occurs when nonrelativistic particles enter the cavities with a transverse offset, even if neither nonlinear optics nor nonlinear beam effects are present. A careful realignment of the injector system will mitigate the present halo. Another possible cure is to reduce the bunch tails by changing the photocathode material from the present GaAs to a multi-alkali that is known to have a shorter longitudinal tail.

Implementing Clinical Research Using Factorial Designs: A Primer.

PubMed

Baker, Timothy B; Smith, Stevens S; Bolt, Daniel M; Loh, Wei-Yin; Mermelstein, Robin; Fiore, Michael C; Piper, Megan E; Collins, Linda M

2017-07-01

Factorial experiments have rarely been used in the development or evaluation of clinical interventions. However, factorial designs offer advantages over randomized controlled trial designs, the latter being much more frequently used in such research. Factorial designs are highly efficient (permitting evaluation of multiple intervention components with good statistical power) and present the opportunity to detect interactions amongst intervention components. Such advantages have led methodologists to advocate for the greater use of factorial designs in research on clinical interventions (Collins, Dziak, & Li, 2009). However, researchers considering the use of such designs in clinical research face a series of choices that have consequential implications for the interpretability and value of the experimental results. These choices include: whether to use a factorial design, selection of the number and type of factors to include, how to address the compatibility of the different factors included, whether and how to avoid confounds between the type and number of interventions a participant receives, and how to interpret interactions. The use of factorial designs in clinical intervention research poses choices that differ from those typically considered in randomized clinical trial designs. However, the great information yield of the former encourages clinical researchers' increased and careful execution of such designs. Copyright © 2017. Published by Elsevier Ltd.

1. VIEW TO SOUTHEAST (NORTHWEST CORNER OF EDIBLE FATS FACTORY) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW TO SOUTHEAST (NORTHWEST CORNER OF EDIBLE FATS FACTORY) - Wilson's Oil House, Lard Refinery, & Edible Fats Factory, Edible Fats Factory, 2801 Southwest Fifteenth Street, Oklahoma City, Oklahoma County, OK

3. VIEW TO SOUTHWEST (NORTHEAST CORNER OF EDIBLE FATS FACTORY) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. VIEW TO SOUTHWEST (NORTHEAST CORNER OF EDIBLE FATS FACTORY) - Wilson's Oil House, Lard Refinery, & Edible Fats Factory, Edible Fats Factory, 2801 Southwest Fifteenth Street, Oklahoma City, Oklahoma County, OK

4. SOUTHEAST CORNER OF EDIBLE FATS FACTORY (CONNECTING BUILDING ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. SOUTHEAST CORNER OF EDIBLE FATS FACTORY (CONNECTING BUILDING ON THE LEFT) - Wilson's Oil House, Lard Refinery, & Edible Fats Factory, Edible Fats Factory, 2801 Southwest Fifteenth Street, Oklahoma City, Oklahoma County, OK

Study of radiative bottomonium transitions using converted photons

NASA Astrophysics Data System (ADS)

Lees, J. P.; Poireau, V.; Prencipe, E.; Tisserand, V.; Garra Tico, J.; Grauges, E.; Martinelli, M.; Milanes, D. A.; Palano, A.; Pappagallo, M.; Eigen, G.; Stugu, B.; Sun, L.; Brown, D. N.; Kerth, L. T.; Kolomensky, Yu. G.; Lynch, G.; Koch, H.; Schroeder, T.; Asgeirsson, D. J.; Hearty, C.; Mattison, T. S.; McKenna, J. A.; Khan, A.; Blinov, V. E.; Buzykaev, A. R.; Druzhinin, V. P.; Golubev, V. B.; Kravchenko, E. A.; Onuchin, A. P.; Serednyakov, S. I.; Skovpen, Yu. I.; Solodov, E. P.; Todyshev, K. Yu.; Yushkov, A. N.; Bondioli, M.; Curry, S.; Kirkby, D.; Lankford, A. J.; Mandelkern, M.; Stoker, D. P.; Atmacan, H.; Gary, J. W.; Liu, F.; Long, O.; Vitug, G. M.; Campagnari, C.; Hong, T. M.; Kovalskyi, D.; Richman, J. D.; West, C. A.; Eisner, A. M.; Kroseberg, J.; Lockman, W. S.; Martinez, A. J.; Schalk, T.; Schumm, B. A.; Seiden, A.; Cheng, C. H.; Doll, D. A.; Echenard, B.; Flood, K. T.; Hitlin, D. G.; Ongmongkolkul, P.; Porter, F. C.; Rakitin, A. Y.; Andreassen, R.; Dubrovin, M. S.; Meadows, B. T.; Sokoloff, M. D.; Bloom, P. C.; Ford, W. T.; Gaz, A.; Nagel, M.; Nauenberg, U.; Smith, J. G.; Wagner, S. R.; Ayad, R.; Toki, W. H.; Spaan, B.; Kobel, M. J.; Schubert, K. R.; Schwierz, R.; Bernard, D.; Verderi, M.; Clark, P. J.; Playfer, S.; Watson, J. E.; Bettoni, D.; Bozzi, C.; Calabrese, R.; Cibinetto, G.; Fioravanti, E.; Garzia, I.; Luppi, E.; Munerato, M.; Negrini, M.; Piemontese, L.; Baldini-Ferroli, R.; Calcaterra, A.; de Sangro, R.; Finocchiaro, G.; Nicolaci, M.; Pacetti, S.; Patteri, P.; Peruzzi, I. M.; Piccolo, M.; Rama, M.; Zallo, A.; Contri, R.; Guido, E.; Lo Vetere, M.; Monge, M. R.; Passaggio, S.; Patrignani, C.; Robutti, E.; Bhuyan, B.; Prasad, V.; Lee, C. L.; Morii, M.; Edwards, A. J.; Adametz, A.; Marks, J.; Uwer, U.; Bernlochner, F. U.; Ebert, M.; Lacker, H. M.; Lueck, T.; Dauncey, P. D.; Tibbetts, M.; Behera, P. K.; Mallik, U.; Chen, C.; Cochran, J.; Crawley, H. B.; Meyer, W. T.; Prell, S.; Rosenberg, E. I.; Rubin, A. E.; Gritsan, A. V.; Guo, Z. J.; Arnaud, N.; Davier, M.; Derkach, D.; Grosdidier, G.; Le Diberder, F.; Lutz, A. M.; Malaescu, B.; Roudeau, P.; Schune, M. H.; Stocchi, A.; Wormser, G.; Lange, D. J.; Wright, D. M.; Bingham, I.; Chavez, C. A.; Coleman, J. P.; Fry, J. R.; Gabathuler, E.; Hutchcroft, D. E.; Payne, D. J.; Touramanis, C.; Bevan, A. J.; di Lodovico, F.; Sacco, R.; Sigamani, M.; Cowan, G.; Paramesvaran, S.; Brown, D. N.; Davis, C. L.; Denig, A. G.; Fritsch, M.; Gradl, W.; Hafner, A.; Alwyn, K. E.; Bailey, D.; Barlow, R. J.; Jackson, G.; Lafferty, G. D.; Cenci, R.; Hamilton, B.; Jawahery, A.; Roberts, D. A.; Simi, G.; Dallapiccola, C.; Salvati, E.; Cowan, R.; Dujmic, D.; Sciolla, G.; Lindemann, D.; Patel, P. M.; Robertson, S. H.; Schram, M.; Biassoni, P.; Lazzaro, A.; Lombardo, V.; Palombo, F.; Stracka, S.; Cremaldi, L.; Godang, R.; Kroeger, R.; Sonnek, P.; Summers, D. J.; Nguyen, X.; Taras, P.; de Nardo, G.; Monorchio, D.; Onorato, G.; Sciacca, C.; Raven, G.; Snoek, H. L.; Jessop, C. P.; Knoepfel, K. J.; Losecco, J. M.; Wang, W. F.; Honscheid, K.; Kass, R.; Brau, J.; Frey, R.; Sinev, N. B.; Strom, D.; Torrence, E.; Feltresi, E.; Gagliardi, N.; Margoni, M.; Morandin, M.; Posocco, M.; Rotondo, M.; Simonetto, F.; Stroili, R.; Ben-Haim, E.; Bomben, M.; Bonneaud, G. R.; Briand, H.; Calderini, G.; Chauveau, J.; Hamon, O.; Leruste, Ph.; Marchiori, G.; Ocariz, J.; Sitt, S.; Biasini, M.; Manoni, E.; Rossi, A.; Angelini, C.; Batignani, G.; Bettarini, S.; Carpinelli, M.; Casarosa, G.; Cervelli, A.; Forti, F.; Giorgi, M. A.; Lusiani, A.; Neri, N.; Oberhof, B.; Paoloni, E.; Perez, A.; Rizzo, G.; Walsh, J. J.; Lopes Pegna, D.; Lu, C.; Olsen, J.; Smith, A. J. S.; Telnov, A. V.; Anulli, F.; Cavoto, G.; Faccini, R.; Ferrarotto, F.; Ferroni, F.; Gaspero, M.; Li Gioi, L.; Mazzoni, M. A.; Piredda, G.; Bünger, C.; Hartmann, T.; Leddig, T.; Schröder, H.; Waldi, R.; Adye, T.; Olaiya, E. O.; Wilson, F. F.; Emery, S.; Hamel de Monchenault, G.; Vasseur, G.; Yèche, Ch.; Aston, D.; Bard, D. J.; Bartoldus, R.; Benitez, J. F.; Cartaro, C.; Convery, M. R.; Dorfan, J.; Dubois-Felsmann, G. P.; Dunwoodie, W.; Field, R. C.; Franco Sevilla, M.; Fulsom, B. G.; Gabareen, A. M.; Graham, M. T.; Grenier, P.; Hast, C.; Innes, W. R.; Kelsey, M. H.; Kim, H.; Kim, P.; Kocian, M. L.; Leith, D. W. G. S.; Lewis, P.; Li, S.; Lindquist, B.; Luitz, S.; Luth, V.; Lynch, H. L.; Macfarlane, D. B.; Muller, D. R.; Neal, H.; Nelson, S.; Ofte, I.; Perl, M.; Pulliam, T.; Ratcliff, B. N.; Roodman, A.; Salnikov, A. A.; Santoro, V.; Schindler, R. H.; Snyder, A.; Su, D.; Sullivan, M. K.; Va'Vra, J.; Wagner, A. P.; Weaver, M.; Wisniewski, W. J.; Wittgen, M.; Wright, D. H.; Wulsin, H. W.; Yarritu, A. K.; Young, C. C.; Ziegler, V.; Park, W.; Purohit, M. V.; White, R. M.; Wilson, J. R.; Randle-Conde, A.; Sekula, S. J.; Bellis, M.; Burchat, P. R.; Miyashita, T. S.; Alam, M. S.; Ernst, J. A.; Gorodeisky, R.; Guttman, N.; Peimer, D. R.; Soffer, A.; Lund, P.; Spanier, S. M.; Eckmann, R.; Ritchie, J. L.; Ruland, A. M.; Schilling, C. J.; Schwitters, R. F.; Wray, B. C.; Izen, J. M.; Lou, X. C.; Bianchi, F.; Gamba, D.; Lanceri, L.; Vitale, L.; Lopez-March, N.; Martinez-Vidal, F.; Oyanguren, A.; Ahmed, H.; Albert, J.; Banerjee, Sw.; Choi, H. H. F.; King, G. J.; Kowalewski, R.; Lewczuk, M. J.; Lindsay, C.; Nugent, I. M.; Roney, J. M.; Sobie, R. J.; Gershon, T. J.; Harrison, P. F.; Latham, T. E.; Puccio, E. M. T.; Band, H. R.; Dasu, S.; Pan, Y.; Prepost, R.; Vuosalo, C. O.; Wu, S. L.

2011-10-01

We use (111±1) million Υ(3S) and (89±1) million Υ(2S) events recorded by the BABAR detector at the PEP-II B-factory at SLAC to perform a study of radiative transitions between bottomonium states using photons that have been converted to e+e- pairs by the detector material. We observe Υ(3S)→γχb0,2(1P) decay, make precise measurements of the branching fractions for χb1,2(1P,2P)→γΥ(1S) and χb1,2(2P)→γΥ(2S) decays, and search for radiative decay to the ηb(1S) and ηb(2S) states.

Measurement of radiation damage on an epoxy-based optical glue

NASA Astrophysics Data System (ADS)

Huang, H. C.; Peng, K. C.; Sahu, S. K.; Ueno, K.; Chang, Y. H.; Wang, C. H.; Hou, W. S.

1997-02-01

We measured the radiation damage on an optical glue called Eccobond-24, which is a candidate for CsI and BGO crystal calorimeters of the BELLE detector of the KEK B-factory. Absorption spectrophotometry in the range 300-800 nm was used to monitor the radiation damage. The maximum equivalent dose was 1.64 Mrad. The glue shows effects of damage, but is acceptable for the radiation level in the above-mentioned experiment.

Engineering the smart factory

NASA Astrophysics Data System (ADS)

Harrison, Robert; Vera, Daniel; Ahmad, Bilal

2016-10-01

The fourth industrial revolution promises to create what has been called the smart factory. The vision is that within such modular structured smart factories, cyber-physical systems monitor physical processes, create a virtual copy of the physical world and make decentralised decisions. This paper provides a view of this initiative from an automation systems perspective. In this context it considers how future automation systems might be effectively configured and supported through their lifecycles and how integration, application modelling, visualisation and reuse of such systems might be best achieved. The paper briefly describes limitations in current engineering methods, and new emerging approaches including the cyber physical systems (CPS) engineering tools being developed by the automation systems group (ASG) at Warwick Manufacturing Group, University of Warwick, UK.

Asymptotic Normality Through Factorial Cumulants and Partition Identities

PubMed Central

Bobecka, Konstancja; Hitczenko, Paweł; López-Blázquez, Fernando; Rempała, Grzegorz; Wesołowski, Jacek

2013-01-01

In the paper we develop an approach to asymptotic normality through factorial cumulants. Factorial cumulants arise in the same manner from factorial moments as do (ordinary) cumulants from (ordinary) moments. Another tool we exploit is a new identity for ‘moments’ of partitions of numbers. The general limiting result is then used to (re-)derive asymptotic normality for several models including classical discrete distributions, occupancy problems in some generalized allocation schemes and two models related to negative multinomial distribution. PMID:24591773

Factorial Experiments: Efficient Tools for Evaluation of Intervention Components

PubMed Central

Collins, Linda M.; Dziak, John J.; Kugler, Kari C.; Trail, Jessica B.

2014-01-01

Background An understanding of the individual and combined effects of a set of intervention components is important for moving the science of preventive medicine interventions forward. This understanding can often be achieved in an efficient and economical way via a factorial experiment, in which two or more independent variables are manipulated. The factorial experiment is a complement to the randomized controlled trial (RCT); the two designs address different research questions. Purpose This article offers an introduction to factorial experiments aimed at investigators trained primarily in the RCT. Method The factorial experiment is compared and contrasted with other experimental designs used commonly in intervention science to highlight where each is most efficient and appropriate. Results Several points are made: factorial experiments make very efficient use of experimental subjects when the data are properly analyzed; a factorial experiment can have excellent statistical power even if it has relatively few subjects per experimental condition; and when conducting research to select components for inclusion in a multicomponent intervention, interactions should be studied rather than avoided. Conclusions Investigators in preventive medicine and related areas should begin considering factorial experiments alongside other approaches. Experimental designs should be chosen from a resource management perspective, which states that the best experimental design is the one that provides the greatest scientific benefit without exceeding available resources. PMID:25092122

Factorial experiments: efficient tools for evaluation of intervention components.

PubMed

Collins, Linda M; Dziak, John J; Kugler, Kari C; Trail, Jessica B

2014-10-01

An understanding of the individual and combined effects of a set of intervention components is important for moving the science of preventive medicine interventions forward. This understanding can often be achieved in an efficient and economical way via a factorial experiment, in which two or more independent variables are manipulated. The factorial experiment is a complement to the RCT; the two designs address different research questions. To offer an introduction to factorial experiments aimed at investigators trained primarily in the RCT. The factorial experiment is compared and contrasted with other experimental designs used commonly in intervention science to highlight where each is most efficient and appropriate. Several points are made: factorial experiments make very efficient use of experimental subjects when the data are properly analyzed; a factorial experiment can have excellent statistical power even if it has relatively few subjects per experimental condition; and when conducting research to select components for inclusion in a multicomponent intervention, interactions should be studied rather than avoided. Investigators in preventive medicine and related areas should begin considering factorial experiments alongside other approaches. Experimental designs should be chosen from a resource management perspective, which states that the best experimental design is the one that provides the greatest scientific benefit without exceeding available resources. Copyright © 2014 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Ergonomic analysis jobs in recovered factories.

PubMed

Cuenca, Gabriela; Zotta, Gastón

2012-01-01

With the advent of the deep economic crisis in Argentina on 2001, the recovery of companies through to the creation of the Cooperatives Working Self-Management or Factories Recovered by its workers was constituted as one of the ways in which the salaried disobeyed the increasing unemployment. When the companies turn into recovered factories they tend to leave of side practices that have been seen like imposed by the previous organization and not understanding them as a primary condition for the execution of his tasks. Safety and ergonomics are two disciplines that are no longer considered relevant to the daily work. Therefore this investigation aims to revalue, undergo semantic to give back to a place in every organization analyzed. This research developed a self-diagnostic tool for working conditions, and the environment, present in the recovered factories.

Two-photon interference of temporally separated photons.

PubMed

Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

2016-10-06

We present experimental demonstrations of two-photon interference involving temporally separated photons within two types of interferometers: a Mach-Zehnder interferometer and a polarization-based Michelson interferometer. The two-photon states are probabilistically prepared in a symmetrically superposed state within the two interferometer arms by introducing a large time delay between two input photons; this state is composed of two temporally separated photons, which are in two different or the same spatial modes. We then observe two-photon interference fringes involving both the Hong-Ou-Mandel interference effect and the interference of path-entangled two-photon states simultaneously in a single interferometric setup. The observed two-photon interference fringes provide simultaneous observation of the interferometric properties of the single-photon and two-photon wavepackets. The observations can also facilitate a more comprehensive understanding of the origins of the interference phenomena arising from spatially bunched/anti-bunched two-photon states comprised of two temporally separated photons within the interferometer arms.

Two-photon interference of temporally separated photons

PubMed Central

Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

2016-01-01

We present experimental demonstrations of two-photon interference involving temporally separated photons within two types of interferometers: a Mach-Zehnder interferometer and a polarization-based Michelson interferometer. The two-photon states are probabilistically prepared in a symmetrically superposed state within the two interferometer arms by introducing a large time delay between two input photons; this state is composed of two temporally separated photons, which are in two different or the same spatial modes. We then observe two-photon interference fringes involving both the Hong-Ou-Mandel interference effect and the interference of path-entangled two-photon states simultaneously in a single interferometric setup. The observed two-photon interference fringes provide simultaneous observation of the interferometric properties of the single-photon and two-photon wavepackets. The observations can also facilitate a more comprehensive understanding of the origins of the interference phenomena arising from spatially bunched/anti-bunched two-photon states comprised of two temporally separated photons within the interferometer arms. PMID:27708380

Compensation of orbit distortion due to quadrupole motion using feed-forward control at KEK ATF

NASA Astrophysics Data System (ADS)

Bett, D. R.; Charrondière, C.; Patecki, M.; Pfingstner, J.; Schulte, D.; Tomás, R.; Jeremie, A.; Kubo, K.; Kuroda, S.; Naito, T.; Okugi, T.; Tauchi, T.; Terunuma, N.; Burrows, P. N.; Christian, G. B.; Perry, C.

2018-07-01

The high luminosity requirement for a future linear collider sets a demanding limit on the beam quality at the Interaction Point (IP). One potential source of luminosity loss is the motion of the ground itself. The resulting misalignments of the quadrupole magnets cause distortions to the beam orbit and hence an increase in the beam emittance. This paper describes a technique for compensating this orbit distortion by using seismometers to monitor the misalignment of the quadrupole magnets in real-time. The first demonstration of the technique was achieved at the Accelerator Test Facility (ATF) at KEK in Japan. The feed-forward system consisted of a seismometer-based quadrupole motion monitoring system, an FPGA-based feed-forward processor and a stripline kicker plus associated electronics. Through the application of a kick calculated from the position of a single quadruple, the system was able to remove about 80% of the component of the beam jitter that was correlated to the motion of the quadrupole. As a significant fraction of the orbit jitter in the ATF final focus is due to sources other than quadrupole misalignment, this amounted to an approximately 15% reduction in the absolute beam jitter.

A simple model for factory distribution: Historical effect in an industry city

NASA Astrophysics Data System (ADS)

Uehara, Takashi; Sato, Kazunori; Morita, Satoru; Maeda, Yasunobu; Yoshimura, Jin; Tainaka, Kei-ichi

2016-02-01

The construction and discontinuance processes of factories are complicated problems in sociology. We focus on the spatial and temporal changes of factories at Hamamatsu city in Japan. Real data indicate that the clumping degree of factories decreases as the density of factory increases. To represent the spatial and temporal changes of factories, we apply "contact process" which is one of cellular automata. This model roughly explains the dynamics of factory distribution. We also find "historical effect" in spatial distribution. Namely, the recent factories have been dispersed due to the past distribution during the period of economic bubble. This effect may be related to heavy shock in Japanese stock market.

The Clone Factory

ERIC Educational Resources Information Center

Stoddard, Beryl

2005-01-01

Have humans been cloned? Is it possible? Immediate interest is sparked when students are asked these questions. In response to their curiosity, the clone factory activity was developed to help them understand the process of cloning. In this activity, students reenact the cloning process, in a very simplified simulation. After completing the…

Testing Factorial Invariance in Multilevel Data: A Monte Carlo Study

ERIC Educational Resources Information Center

Kim, Eun Sook; Kwok, Oi-man; Yoon, Myeongsun

2012-01-01

Testing factorial invariance has recently gained more attention in different social science disciplines. Nevertheless, when examining factorial invariance, it is generally assumed that the observations are independent of each other, which might not be always true. In this study, we examined the impact of testing factorial invariance in multilevel…

Lattice and beam optics design for suppression of CSR-induced emittance growth at the KEK-ERL test facility

NASA Astrophysics Data System (ADS)

Shimada, M.; Yokoya, K.; Suwada, T.; Enomoto, A.

2007-06-01

The lattice and beam optics of the arc section of the KEK-ERL test facility, having an energy of 200 MeV, were optimized to efficiently suppress emittance growth based on a simulation using a particle-tracking method taking coherent synchrotron radiation effects into account. The lattice optimization in the arc section was performed under two conditions: a high-current mode with a bunch charge of 76.9 pC without bunch compression, and a short-bunch mode with bunch compression, producing a final bunch length of around 0.1 ps. The simulation results showed that, in the high-current mode, emittance growth was efficiently suppressed by keeping a root-mean-square (rms) bunch length of 1 ps at a bunch charge of 76.9 pC, and in the short-bunch mode, emittance growth was kept within permissible limits with a maximum allowable bunch charge of 23.1 pC at an rms bunch length of 0.1 ps.

The Virtual Factory Teaching System (VFTS): Project Review and Results.

ERIC Educational Resources Information Center

Kazlauskas, E. J.; Boyd, E. F., III; Dessouky, M. M.

This paper presents a review of the Virtual Factory Teaching (VFTS) project, a Web-based, multimedia collaborative learning network. The system allows students, working alone or in teams, to build factories, forecast demand for products, plan production, establish release rules for new work into the factory, and set scheduling rules for…

The Old Factory

ERIC Educational Resources Information Center

Roman, Harry T.

2007-01-01

Technology education is not just about things, systems, and processes. It can also be about history, people, technological change, and impacts on society. In this design challenge, one uses technology education principles and ideas to convert an old factory into a museum and learning center. The challenge with this historical resource is to think…

Photons, photon jets, and dark photons at 750 GeV and beyond.

PubMed

Dasgupta, Basudeb; Kopp, Joachim; Schwaller, Pedro

2016-01-01

In new physics searches involving photons at the LHC, one challenge is to distinguish scenarios with isolated photons from models leading to "photon jets". For instance, in the context of the 750 GeV diphoton excess, it was pointed out that a true diphoton resonance [Formula: see text] can be mimicked by a process of the form [Formula: see text], where S is a new scalar with a mass of 750 GeV and a is a light pseudoscalar decaying to two collinear photons. Photon jets can be distinguished from isolated photons by exploiting the fact that a large fraction of photons convert to an [Formula: see text] pair inside the inner detector. In this note, we quantify this discrimination power, and we study how the sensitivity of future searches differs for photon jets compared to isolated photons. We also investigate how our results depend on the lifetime of the particle(s) decaying to the photon jet. Finally, we discuss the extension to [Formula: see text], where there are no photons at all but the dark photon [Formula: see text] decays to [Formula: see text] pairs. Our results will be useful in future studies of the putative 750 GeV signal, but also more generally in any new physics search involving hard photons.

The Learning Factory.

ERIC Educational Resources Information Center

Alef, Edward R.; Berg, Daniel

This book looks at the administration of an academic institution as a learning factory which needs to be run like a business, competing with other businesses offering the same service. The book begins with a discussion of the concepts of the continuing education learning market, the playing fields and rules of the games, as well as the idea of…

27 CFR 40.47 - Other businesses within factory.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2012-04-01 2011-04-01 true Other businesses within... AND TUBES, AND PROCESSED TOBACCO Administrative Provisions § 40.47 Other businesses within factory. (a) General. The appropriate TTB officer may authorize such other businesses within the factory of a...

27 CFR 40.47 - Other businesses within factory.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2014-04-01 2014-04-01 false Other businesses within... AND TUBES, AND PROCESSED TOBACCO Administrative Provisions § 40.47 Other businesses within factory. (a) General. The appropriate TTB officer may authorize such other businesses within the factory of a...

Gravitational waves from dark first order phase transitions and dark photons

NASA Astrophysics Data System (ADS)

Addazi, Andrea; Marcianò, Antonino

2018-01-01

Cold Dark Matter particles may interact with ordinary particles through a dark photon, which acquires a mass thanks to a spontaneous symmetry breaking mechanism. We discuss a dark photon model in which the scalar singlet associated to the spontaneous symmetry breaking has an effective potential that induces a first order phase transition in the early Universe. Such a scenario provides a rich phenomenology for electron-positron colliders and gravitational waves interferometers, and may be tested in several different channels. The hidden first order phase transition implies the emission of gravitational waves signals, which may constrain the dark photon’s space of parameters. Compared limits from electron-positron colliders, astrophysics, cosmology and future gravitational waves interferometers such as eLISA, U-DECIGO and BBO are discussed. This highly motivates a cross-checking strategy of data arising from experiments dedicated to gravitational waves, meson factories, the International Linear Collider (ILC), the Circular Electron Positron Collider (CEPC) and other underground direct detection experiments of cold dark matter candidates. Supported by the Shanghai Municipality (KBH1512299) and Fudan University (JJH1512105)

Three-photon N00N states generated by photon subtraction from double photon pairs.

PubMed

Kim, Heonoh; Park, Hee Su; Choi, Sang-Kyung

2009-10-26

We describe an experimental demonstration of a novel three-photon N00N state generation scheme using a single source of photons based on spontaneous parametric down-conversion (SPDC). The three-photon entangled state is generated when a photon is subtracted from a double pair of photons and detected by a heralding counter. Interference fringes measured with an emulated three-photon detector reveal the three-photon de Broglie wavelength and exhibit visibility > 70% without background subtraction.

Operating a production pilot factory serving several scientific domains

NASA Astrophysics Data System (ADS)

Sfiligoi, I.; Würthwein, F.; Andrews, W.; Dost, J. M.; MacNeill, I.; McCrea, A.; Sheripon, E.; Murphy, C. W.

2011-12-01

Pilot infrastructures are becoming prominent players in the Grid environment. One of the major advantages is represented by the reduced effort required by the user communities (also known as Virtual Organizations or VOs) due to the outsourcing of the Grid interfacing services, i.e. the pilot factory, to Grid experts. One such pilot factory, based on the glideinWMS pilot infrastructure, is being operated by the Open Science Grid at University of California San Diego (UCSD). This pilot factory is serving multiple VOs from several scientific domains. Currently the three major clients are the analysis operations of the HEP experiment CMS, the community VO HCC, which serves mostly math, biology and computer science users, and the structural biology VO NEBioGrid. The UCSD glidein factory allows the served VOs to use Grid resources distributed over 150 sites in North and South America, in Europe, and in Asia. This paper presents the steps taken to create a production quality pilot factory, together with the challenges encountered along the road.

Photon correlation in single-photon frequency upconversion.

PubMed

Gu, Xiaorong; Huang, Kun; Pan, Haifeng; Wu, E; Zeng, Heping

2012-01-30

We experimentally investigated the intensity cross-correlation between the upconverted photons and the unconverted photons in the single-photon frequency upconversion process with multi-longitudinal mode pump and signal sources. In theoretical analysis, with this multi-longitudinal mode of both signal and pump sources system, the properties of the signal photons could also be maintained as in the single-mode frequency upconversion system. Experimentally, based on the conversion efficiency of 80.5%, the joint probability of simultaneously detecting at upconverted and unconverted photons showed an anti-correlation as a function of conversion efficiency which indicated the upconverted photons were one-to-one from the signal photons. While due to the coherent state of the signal photons, the intensity cross-correlation function g(2)(0) was shown to be equal to unity at any conversion efficiency, agreeing with the theoretical prediction. This study will benefit the high-speed wavelength-tunable quantum state translation or photonic quantum interface together with the mature frequency tuning or longitudinal mode selection techniques.

Deterministic photon-emitter coupling in chiral photonic circuits.

PubMed

Söllner, Immo; Mahmoodian, Sahand; Hansen, Sofie Lindskov; Midolo, Leonardo; Javadi, Alisa; Kiršanskė, Gabija; Pregnolato, Tommaso; El-Ella, Haitham; Lee, Eun Hye; Song, Jin Dong; Stobbe, Søren; Lodahl, Peter

2015-09-01

Engineering photon emission and scattering is central to modern photonics applications ranging from light harvesting to quantum-information processing. To this end, nanophotonic waveguides are well suited as they confine photons to a one-dimensional geometry and thereby increase the light-matter interaction. In a regular waveguide, a quantum emitter interacts equally with photons in either of the two propagation directions. This symmetry is violated in nanophotonic structures in which non-transversal local electric-field components imply that photon emission and scattering may become directional. Here we show that the helicity of the optical transition of a quantum emitter determines the direction of single-photon emission in a specially engineered photonic-crystal waveguide. We observe single-photon emission into the waveguide with a directionality that exceeds 90% under conditions in which practically all the emitted photons are coupled to the waveguide. The chiral light-matter interaction enables deterministic and highly directional photon emission for experimentally achievable on-chip non-reciprocal photonic elements. These may serve as key building blocks for single-photon optical diodes, transistors and deterministic quantum gates. Furthermore, chiral photonic circuits allow the dissipative preparation of entangled states of multiple emitters for experimentally achievable parameters, may lead to novel topological photon states and could be applied for directional steering of light.

Deterministic photon-emitter coupling in chiral photonic circuits

NASA Astrophysics Data System (ADS)

Söllner, Immo; Mahmoodian, Sahand; Hansen, Sofie Lindskov; Midolo, Leonardo; Javadi, Alisa; Kiršanskė, Gabija; Pregnolato, Tommaso; El-Ella, Haitham; Lee, Eun Hye; Song, Jin Dong; Stobbe, Søren; Lodahl, Peter

2015-09-01

Engineering photon emission and scattering is central to modern photonics applications ranging from light harvesting to quantum-information processing. To this end, nanophotonic waveguides are well suited as they confine photons to a one-dimensional geometry and thereby increase the light-matter interaction. In a regular waveguide, a quantum emitter interacts equally with photons in either of the two propagation directions. This symmetry is violated in nanophotonic structures in which non-transversal local electric-field components imply that photon emission and scattering may become directional. Here we show that the helicity of the optical transition of a quantum emitter determines the direction of single-photon emission in a specially engineered photonic-crystal waveguide. We observe single-photon emission into the waveguide with a directionality that exceeds 90% under conditions in which practically all the emitted photons are coupled to the waveguide. The chiral light-matter interaction enables deterministic and highly directional photon emission for experimentally achievable on-chip non-reciprocal photonic elements. These may serve as key building blocks for single-photon optical diodes, transistors and deterministic quantum gates. Furthermore, chiral photonic circuits allow the dissipative preparation of entangled states of multiple emitters for experimentally achievable parameters, may lead to novel topological photon states and could be applied for directional steering of light.

Single photon source with individualized single photon certifications

NASA Astrophysics Data System (ADS)

Migdall, Alan L.; Branning, David A.; Castelletto, Stefania; Ware, M.

2002-12-01

As currently implemented, single-photon sources cannot be made to produce single photons with high probability, while simultaneously suppressing the probability of yielding two or more photons. Because of this, single photon sources cannot really produce single photons on demand. We describe a multiplexed system that allows the probabilities of producing one and more photons to be adjusted independently, enabling a much better approximation of a source of single photons on demand. The scheme uses a heralded photon source based on parametric downconversion, but by effectively breaking the trigger detector area into multiple regions, we are able to extract more information about a heralded photon than is possible with a conventional arrangement. This scheme allows photons to be produced along with a quantitative 'certification' that they are single photons. Some of the single-photon certifications can be significantly better than what is possible with conventional downconversion sources, as well as being better than faint laser sources. With such a source of more tightly certified single photons, it should be possible to improve the maximum secure bit rate possible over a quantum cryptographic link. We present an analysis of the relative merits of this method over the conventional arrangement.

Broadband photon-photon interactions mediated by cold atoms in a photonic crystal fiber

PubMed Central

Litinskaya, Marina; Tignone, Edoardo; Pupillo, Guido

2016-01-01

We demonstrate theoretically that photon-photon attraction can be engineered in the continuum of scattering states for pairs of photons propagating in a hollow-core photonic crystal fiber filled with cold atoms. The atoms are regularly spaced in an optical lattice configuration and the photons are resonantly tuned to an internal atomic transition. We show that the hard-core repulsion resulting from saturation of the atomic transitions induces bunching in the photonic component of the collective atom-photon modes (polaritons). Bunching is obtained in a frequency range as large as tens of GHz, and can be controlled by the inter-atomic separation. We provide a fully analytical explanation for this phenomenon by proving that correlations result from a mismatch of the quantization volumes for atomic excitations and photons in the continuum. Even stronger correlations can be observed for in-gap two-polariton bound states. Our theoretical results use parameters relevant for current experiments and suggest a simple and feasible way to induce interactions between photons. PMID:27170160

Design, analysis and presentation of factorial randomised controlled trials

PubMed Central

Montgomery, Alan A; Peters, Tim J; Little, Paul

2003-01-01

Background The evaluation of more than one intervention in the same randomised controlled trial can be achieved using a parallel group design. However this requires increased sample size and can be inefficient, especially if there is also interest in considering combinations of the interventions. An alternative may be a factorial trial, where for two interventions participants are allocated to receive neither intervention, one or the other, or both. Factorial trials require special considerations, however, particularly at the design and analysis stages. Discussion Using a 2 × 2 factorial trial as an example, we present a number of issues that should be considered when planning a factorial trial. The main design issue is that of sample size. Factorial trials are most often powered to detect the main effects of interventions, since adequate power to detect plausible interactions requires greatly increased sample sizes. The main analytical issues relate to the investigation of main effects and the interaction between the interventions in appropriate regression models. Presentation of results should reflect the analytical strategy with an emphasis on the principal research questions. We also give an example of how baseline and follow-up data should be presented. Lastly, we discuss the implications of the design, analytical and presentational issues covered. Summary Difficulties in interpreting the results of factorial trials if an influential interaction is observed is the cost of the potential for efficient, simultaneous consideration of two or more interventions. Factorial trials can in principle be designed to have adequate power to detect realistic interactions, and in any case they are the only design that allows such effects to be investigated. PMID:14633287

Efficiency in Complexity: Composition and Dynamic Nature of Mimivirus Replication Factories

PubMed Central

Milrot, Elad; Mutsafi, Yael; Ben-Dor, Shifra; Levin, Yishai; Savidor, Alon; Kartvelishvily, Elena

2016-01-01

ABSTRACT The recent discovery of multiple giant double-stranded DNA (dsDNA) viruses blurred the consensual distinction between viruses and cells due to their size, as well as to their structural and genetic complexity. A dramatic feature revealed by these viruses as well as by many positive-strand RNA viruses is their ability to rapidly form elaborate intracellular organelles, termed “viral factories,” where viral progeny are continuously generated. Here we report the first isolation of viral factories at progressive postinfection time points. The isolated factories were subjected to mass spectrometry-based proteomics, bioinformatics, and imaging analyses. These analyses revealed that numerous viral proteins are present in the factories but not in mature virions, thus implying that multiple and diverse proteins are required to promote the efficiency of viral factories as “production lines” of viral progeny. Moreover, our results highlight the dynamic and highly complex nature of viral factories, provide new and general insights into viral infection, and substantiate the intriguing notion that viral factories may represent the living state of viruses. IMPORTANCE Large dsDNA viruses such as vaccinia virus and the giant mimivirus, as well as many positive-strand RNA viruses, generate elaborate cytoplasmic organelles in which the multiple and diverse transactions required for viral replication and assembly occur. These organelles, which were termed “viral factories,” are attracting much interest due to the increasing realization that the rapid and continuous production of viral progeny is a direct outcome of the elaborate structure and composition of the factories, which act as efficient production lines. To get new insights into the nature and function of viral factories, we devised a method that allows, for the first time, the isolation of these organelles. Analyses of the isolated factories generated at different times postinfection by mass spectrometry

A Classroom of Polymer Factories.

ERIC Educational Resources Information Center

Harris, Mary E.; Van Natta, Sandra

1998-01-01

Provides an activity in which students create small classroom factories and investigate several aspects of production including design, engineering, quality control, waste management, packaging, shipment, and communication. (DDR)

Engineering Robustness of Microbial Cell Factories.

PubMed

Gong, Zhiwei; Nielsen, Jens; Zhou, Yongjin J

2017-10-01

Metabolic engineering and synthetic biology offer great prospects in developing microbial cell factories capable of converting renewable feedstocks into fuels, chemicals, food ingredients, and pharmaceuticals. However, prohibitively low production rate and mass concentration remain the major hurdles in industrial processes even though the biosynthetic pathways are comprehensively optimized. These limitations are caused by a variety of factors unamenable for host cell survival, such as harsh industrial conditions, fermentation inhibitors from biomass hydrolysates, and toxic compounds including metabolic intermediates and valuable target products. Therefore, engineered microbes with robust phenotypes is essential for achieving higher yield and productivity. In this review, the recent advances in engineering robustness and tolerance of cell factories is described to cope with these issues and briefly introduce novel strategies with great potential to enhance the robustness of cell factories, including metabolic pathway balancing, transporter engineering, and adaptive laboratory evolution. This review also highlights the integration of advanced systems and synthetic biology principles toward engineering the harmony of overall cell function, more than the specific pathways or enzymes. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Myc Dynamically and Preferentially Relocates to a Transcription Factory Occupied by Igh

PubMed Central

Osborne, Cameron S; Chakalova, Lyubomira; Mitchell, Jennifer A; Horton, Alice; Wood, Andrew L; Bolland, Daniel J; Corcoran, Anne E; Fraser, Peter

2007-01-01

Transcription in mammalian nuclei is highly compartmentalized in RNA polymerase II-enriched nuclear foci known as transcription factories. Genes in cis and trans can share the same factory, suggesting that genes migrate to preassembled transcription sites. We used fluorescent in situ hybridization to investigate the dynamics of gene association with transcription factories during immediate early (IE) gene induction in mouse B lymphocytes. Here, we show that induction involves rapid gene relocation to transcription factories. Importantly, we find that the Myc proto-oncogene on Chromosome 15 is preferentially recruited to the same transcription factory as the highly transcribed Igh gene located on Chromosome 12. Myc and Igh are the most frequent translocation partners in plasmacytoma and Burkitt lymphoma. Our results show that transcriptional activation of IE genes involves rapid relocation to preassembled transcription factories. Furthermore, the data imply a direct link between the nonrandom interchromosomal organization of transcribed genes at transcription factories and the incidence of specific chromosomal translocations. PMID:17622196

Factory overload testing of a large power transformer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Douglas, D.H.; Lawrence, C.O.; Templeton, J.B.

1985-09-01

A factory overload test of up to 150% of the nameplate rating was run on a 224 MVA autotransformer. The results of this test were of great value and were used in identifying transformer overload limitations, in evaluating loading guide oil and winding equations, exponents and time constants, and in helping to perfect a factory overload test procedure.

Hazardous factories: Nigerian evidence.

PubMed

Oloyede, Olajide

2005-06-01

The past 15 years have seen an increasing governmental and corporate concern for the environment worldwide. For governments, information about the environmental performance of the industrial sector is required to inform macro-level decisions about environmental targets such as those required to meet UN directives. However, in many African, Asian, and Latin American countries, researching and reporting company environmental performance is limited. This article serves as a contribution to filling the gap by presenting evidence of physical and chemical risk in Nigerian factories. One hundred and three factories with a total of 5,021 workers were studied. One hundred and twenty physical and chemical hazards were identified and the result shows a high number of workers exposed to such hazards. The study also reveals that workers' awareness level of chemical hazards was high. Yet the danger was perceived in behavioral terms, especially by manufacturing firms, which tend to see environmental investment in an increasingly global economy as detrimental to profitability.

Integrating PCLIPS into ULowell's Lincoln Logs: Factory of the future

NASA Technical Reports Server (NTRS)

Mcgee, Brenda J.; Miller, Mark D.; Krolak, Patrick; Barr, Stanley J.

1990-01-01

We are attempting to show how independent but cooperating expert systems, executing within a parallel production system (PCLIPS), can operate and control a completely automated, fault tolerant prototype of a factory of the future (The Lincoln Logs Factory of the Future). The factory consists of a CAD system for designing the Lincoln Log Houses, two workcells, and a materials handling system. A workcell consists of two robots, part feeders, and a frame mounted vision system.

Two-photon absorption by spectrally shaped entangled photons

NASA Astrophysics Data System (ADS)

Oka, Hisaki

2018-03-01

We theoretically investigate two-photon excitation by spectrally shaped entangled photons with energy anticorrelation in terms of how the real excitation of an intermediate state affects two-photon absorption by entangled photons. Spectral holes are introduced in the entangled photons around the energy levels of an intermediate state so that two-step excitation via the real excitation of the intermediated state can be suppressed. Using a three-level atomic system as an example, we show that the spectral holes well suppress the real excitation of the intermediate state and recover two-photon absorption via a virtual state. Furthermore, for a short pulse close to a monocycle, we show that the excitation efficiency by the spectrally shaped entangled photons can be enhanced a thousand times as large as that by uncorrelated photons.

Gearing up to the factory of the future

NASA Astrophysics Data System (ADS)

Godfrey, D. E.

1985-01-01

The features of factories and manufacturing techniques and tools of the near future are discussed. The spur to incorporate new technologies on the factory floor will originate in management, who must guide the interfacing of computer-enhanced equipment with traditional manpower, materials and machines. Electronic control with responsiveness and flexibility will be the key concept in an integrated approach to processing materials. Microprocessor controlled laser and fluid cutters add accuracy to cutting operations. Unattended operation will become feasible when automated inspection is added to a work station through developments in robot vision. Optimum shop management will be achieved through AI programming of parts manufacturing, optimized work flows, and cost accounting. The automation enhancements will allow designers to affect directly parts being produced on the factory floor.

Congruences for central factorial numbers modulo powers of prime.

PubMed

Wang, Haiqing; Liu, Guodong

2016-01-01

Central factorial numbers are more closely related to the Stirling numbers than the other well-known special numbers, and they play a major role in a variety of branches of mathematics. In the present paper we prove some interesting congruences for central factorial numbers.

Tuning single-photon sources for telecom multi-photon experiments.

PubMed

Greganti, Chiara; Schiansky, Peter; Calafell, Irati Alonso; Procopio, Lorenzo M; Rozema, Lee A; Walther, Philip

2018-02-05

Multi-photon state generation is of great interest for near-future quantum simulation and quantum computation experiments. To-date spontaneous parametric down-conversion is still the most promising process, even though two major impediments still exist: accidental photon noise (caused by the probabilistic non-linear process) and imperfect single-photon purity (arising from spectral entanglement between the photon pairs). In this work, we overcome both of these difficulties by (1) exploiting a passive temporal multiplexing scheme and (2) carefully optimizing the spectral properties of the down-converted photons using periodically-poled KTP crystals. We construct two down-conversion sources in the telecom wavelength regime, finding spectral purities of > 91%, while maintaining high four-photon count rates. We use single-photon grating spectrometers together with superconducting nanowire single-photon detectors to perform a detailed characterization of our multi-photon source. Our methods provide practical solutions to produce high-quality multi-photon states, which are in demand for many quantum photonics applications.

Radiative Penguin Decays at the B Factories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koneke, Karsten; /MIT, LNS

2007-11-16

In this article, I review the most recent results in radiative penguin decays from the B factories Belle and BABAR. Most notably, I will talk about the recent new observations in the decays B {yields} ({rho}/{omega}) {gamma}, a new analysis technique in b {yields} s{gamma}, and first measurements of radiative penguin decays in the B{sup 0}{sub s} meson system. Finally, I will summarize the current status and future prospects of radiative penguin B physics at the B factories.

Optimization of the Neutrino Factory, revisited

NASA Astrophysics Data System (ADS)

Agarwalla, Sanjib K.; Huber, Patrick; Tang, Jian; Winter, Walter

2011-01-01

We perform the baseline and energy optimization of the Neutrino Factory including the latest simulation results on the magnetized iron detector (MIND). We also consider the impact of τ decays, generated by νμ → ντ or ν e → ντ appearance, on the mass hierarchy, CP violation, and θ 13 discovery reaches, which we find to be negligible for the considered detector. For the baseline-energy optimization for small sin2 2 θ 13, we qualitatively recover the results with earlier simulations of the MIND detector. We find optimal baselines of about 2500km to 5000km for the CP violation measurement, where now values of E μ as low as about 12 GeV may be possible. However, for large sin2 2 θ 13, we demonstrate that the lower threshold and the backgrounds reconstructed at lower energies allow in fact for muon energies as low as 5 GeV at considerably shorter baselines, such as FNAL-Homestake. This implies that with the latest MIND analysis, low-and high-energy versions of the Neutrino Factory are just two different versions of the same experiment optimized for different parts of the parameter space. Apart from a green-field study of the updated detector performance, we discuss specific implementations for the two-baseline Neutrino Factory, where the considered detector sites are taken to be currently discussed underground laboratories. We find that reasonable setups can be found for the Neutrino Factory source in Asia, Europe, and North America, and that a triangular-shaped storage ring is possible in all cases based on geometrical arguments only.

Total fume and metal concentrations during welding in selected factories in Jeddah, Saudi Arabia.

PubMed

Balkhyour, Mansour Ahmed; Goknil, Mohammad Khalid

2010-07-01

Welding is a major industrial process used for joining metals. Occupational exposure to welding fumes is a serious occupational health problem all over the world. The degree of risk to welder's health from fumes depends on composition, concentration, and the length of exposure. The aim of this study was to investigate workers' welding fume exposure levels in some industries in Jeddah, Saudi Arabia. In each factory, the air in the breathing zone within 0.5 m from welders was sampled during 8-hour shifts. Total particulates, manganese, copper, and molybdenum concentrations of welding fumes were determined. Mean values of eight-hour average particulate concentrations measured during welding at the welders breathing zone were 6.3 mg/m(3) (Factory 1), 5.3 mg/m(3) (Factory 2), 11.3 mg/m(3) (Factory 3), 6.8 mg/m(3) (Factory 4), 4.7 mg/m(3) (Factory 5), and 3.0 mg/m(3) (Factory 6). Mean values of airborne manganese, copper, and molybdenum levels measured during welding were in the range of 0.010 mg/m(3)-0.477 mg/m(3), 0.001 mg/m(3)-0.080 mg/m(3) and 0.001 mg/m(3)-0.058 mg/m(3) respectively. Mean values of calculated equivalent exposure values were: 1.50 (Factory 1), 1.56 (Factory 2), 5.14 (Factory 3), 2.21 (Factory 4), 2.89 (Factory 5), and 1.20 (Factory 6). The welders in factories 1, 2, 3, and 4 were exposed to welding fume concentration above the SASO limit value, which may increase the risk of respiratory health problems.

Incense and joss stick making in small household factories, Thailand.

PubMed

Siripanich, S; Siriwong, W; Keawrueang, P; Borjan, M; Robson, M

2014-07-01

Incense and joss stick are generally used in the world. Most products were made in small household factories. There are many environmental and occupational hazards in these factories. To evaluate the workplace environmental and occupational hazards in small household incense and joss stick factories in Roi-Et, Thailand. Nine small household factories in rural areas of Roi-Et, Thailand, were studied. Dust concentration and small aerosol particles were counted through real time exposure monitoring. The inductively coupled plasma optical emission spectrometry (ICP-OES) was used for quantitative measurement of heavy metal residue in incense products. Several heavy metals were found in dissolved dye and joss sticks. Those included barium, manganese, and lead. Rolling and shaking processes produced the highest concentration of dust and aerosols. Only 3.9% of female workers used personal protection equipment. Dust and chemicals were major threats in small household incense and joss stick factories in Thailand. Increasing awareness towards using personal protection equipment and emphasis on elimination of environmental workplace hazards should be considered to help the workers of this industry.

Toroidal magnetized iron neutrino detector for a neutrino factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bross, A.; Wands, R.; Bayes, R.

2013-08-01

A neutrino factory has unparalleled physics reach for the discovery and measurement of CP violation in the neutrino sector. A far detector for a neutrino factory must have good charge identification with excellent background rejection and a large mass. An elegant solution is to construct a magnetized iron neutrino detector (MIND) along the lines of MINOS, where iron plates provide a toroidal magnetic field and scintillator planes provide 3D space points. In this report, the current status of a simulation of a toroidal MIND for a neutrino factory is discussed in light of the recent measurements of largemore » $$\\theta_{13}$$. The response and performance using the 10 GeV neutrino factory configuration are presented. It is shown that this setup has equivalent $$\\delta_{CP}$$ reach to a MIND with a dipole field and is sensitive to the discovery of CP violation over 85% of the values of $$\\delta_{CP}$$.« less

Arcnet(R) On-Fiber -- A Viable Factory Automation Alternative

NASA Astrophysics Data System (ADS)

Karlin, Geof; Tucker, Carol S.

1987-01-01

Manufacturers need to improve their operating methods and increase their productivity so they can compete successfully in the marketplace. This goal can be achieved through factory automation, and the key to this automation is successful data base management and factory integration. However, large scale factory automation and integration requires effective communications, and this has given rise to an interest in various Local Area Networks or LANs. In a completely integrated and automated factory, the entire organization must have access to the data base, and all departments and functions must be able to communicate with each other. Traditionally, these departments and functions use incompatible equipment, and the ability to make such equipment communicate presents numerous problems. ARCNET, a token-passing LAN which has a significant presence in the office environment today, coupled with fiber optic cable, the cable of the future, provide an effective, low-cost solution to a number of these problems.

A Linear Accelerator for TA-FD calibration

NASA Astrophysics Data System (ADS)

Shibata, T.; Ikeda, D.; Ikeda, M.; Enomoto, A.; Ohsawa, S.; Kakiha, K.; Kakihara, K.; Sagawa, H.; Satoh, M.; Shidara, T.; Sugimura, T.; Fukushima, M.; Fukuda, S.; Furukawa, K.; Yoshida, M.

The energy of the primary cosmic ray can be calculated from fluorescence photons detected by fluorescence telescope. However, since we can not know the true energy of primary cosmic ray, it is difficult to calibrate between number of photons and energy directly. In TA project, we will create pseudo- cosmic ray events by using accelerated electron beam which is injected in the air. The injected electron beam creates an air shower and fluorescence photons are emitted. We can calibate between electron beam energy which is known exactry and detected photons. We are developping a small linear accelerator (Linac) at High Energy Accelerator Research Organization (KEK) in Japan. The maximum energy is 40MeV, the typical current is 0.16nC, and the intensity per pulse is 6.4mJ. The accuracy of beam energy is less than 1%. The Linac consists of a -100kV pulse type electron gun, a 1.5m pre-buncher and buncher tube, a 2m S-band accelerator tube, a quadrupole magnet, a 90 degree bending magnet, and a S-Band(2856MHz) 50MW high power klystron as RF source. We chekced the performance of the electron beam, energy resolution, beam spread, beam current, and beam loss by PARMELA simulation, and checked the air shower by electron beam and number of the detected photons by detector simulation which are made by GEANT4. In this Spring, we will do the full beam test in KEK. The beam operation in Utah will be started from this Autumn. In this talk, we will report about the results of the beam test and calibration method by this Linac.

1. GENERAL VIEW OF COMPLEX, SHOWING FACTORY BUILDING IN LEFT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. GENERAL VIEW OF COMPLEX, SHOWING FACTORY BUILDING IN LEFT FOREGROUND, GRINDING PLATFORM AT REAR OF FACTORY, AND STABLE AREA AND OVERSEER'S HOUSE TO RIGHT - Caneel Bay Plantation, General Views, Cruz Bay, St. John, VI

The Japanese Positron Factory

NASA Astrophysics Data System (ADS)

Okada, S.; Sunaga, H.; Kaneko, H.; Takizawa, H.; Kawasuso, A.; Yotsumoto, K.; Tanaka, R.

1999-06-01

The Positron Factory has been planned at Japan Atomic Energy Research Institute (JAERI). The factory is expected to produce linac-based monoenergetic positron beams having world-highest intensities of more than 1010e+/sec, which will be applied for R&D of materials science, biotechnology and basic physics & chemistry. In this article, results of the design studies are demonstrated for the following essential components of the facilities: 1) Conceptual design of a high-power electron linac with 100 MeV in beam energy and 100 kW in averaged beam power, 2) Performance tests of the RF window in the high-power klystron and of the electron beam window, 3) Development of a self-driven rotating electron-to-positron converter and the performance tests, 4) Proposal of multi-channel beam generation system for monoenergetic positrons, with a series of moderator assemblies based on a newly developed Monte Carlo simulation and the demonstrative experiment, 5) Proposal of highly efficient moderator structures, 6) Conceptual design of a local shield to suppress the surrounding radiation and activation levels.

CMOS-compatible photonic devices for single-photon generation

NASA Astrophysics Data System (ADS)

Xiong, Chunle; Bell, Bryn; Eggleton, Benjamin J.

2016-09-01

Sources of single photons are one of the key building blocks for quantum photonic technologies such as quantum secure communication and powerful quantum computing. To bring the proof-of-principle demonstration of these technologies from the laboratory to the real world, complementary metal-oxide-semiconductor (CMOS)-compatible photonic chips are highly desirable for photon generation, manipulation, processing and even detection because of their compactness, scalability, robustness, and the potential for integration with electronics. In this paper, we review the development of photonic devices made from materials (e.g., silicon) and processes that are compatible with CMOS fabrication facilities for the generation of single photons.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohmi, K.

In recent high luminosity colliders, the finite crossing angle scheme becomes popular to gain the multiplicity of luminosity with multi-bunch or long bunch operation. Success of KEKB showed that the finite crossing angle scheme was no problem to achieve the beam-beam parameter up to 0.05. The authors have studied the beam-beam interactions with/without crossing angle toward higher luminosity. They discuss how the crossing angle affects the beam-beam parameter and luminosity in the present KEK B factory (KEKB) using computer simulations.

Microbially induced and microbially catalysed precipitation: two different carbonate factories

NASA Astrophysics Data System (ADS)

Meister, Patrick

2016-04-01

The landmark paper by Schlager (2003) has revealed three types of benthic carbonate production referred to as "carbonate factories", operative at different locations at different times in Earth history. The tropical or T-factory comprises the classical platforms and fringing reefs and is dominated by carbonate precipitation by autotrophic calcifying metazoans ("biotically controlled" precipitation). The cool or C-factory is also biotically controlled but via heterotrophic, calcifying metazoans in cold and deep waters at the continental margins. A further type is the mud-mound or M-factory, where carbonate precipitation is supported by microorganisms but not controlled by a specific enzymatic pathway ("biotically induced" precipitation). How exactly the microbes influence precipitation is still poorly understood. Based on recent experimental and field studies, the microbial influence on modern mud mound and microbialite growth includes two fundamentally different processes: (1) Metabolic activity of microbes may increase the saturation state with respect to a particular mineral phase, thereby indirectly driving the precipitation of the mineral phase: microbially induced precipitation. (2) In a situation, where a solution is already supersaturated but precipitation of the mineral is inhibited by a kinetic barrier, microbes may act as a catalyser, i.e. they lower the kinetic barrier: microbially catalysed precipitation. Such a catalytic effect can occur e.g. via secreted polymeric substances or specific chemical groups on the cell surface, at which the minerals nucleate or which facilitate mechanistically the bonding of new ions to the mineral surface. Based on these latest developments in microbialite formation, I propose to extend the scheme of benthic carbonate factories of Schlager et al. (2003) by introducing an additional branch distinguishing microbially induced from microbially catalysed precipitation. Although both mechanisms could be operative in a M-factory

Undergraduate students' initial conceptions of factorials

NASA Astrophysics Data System (ADS)

Lockwood, Elise; Erickson, Sarah

2017-05-01

Counting problems offer rich opportunities for students to engage in mathematical thinking, but they can be difficult for students to solve. In this paper, we present a study that examines student thinking about one concept within counting, factorials, which are a key aspect of many combinatorial ideas. In an effort to better understand students' conceptions of factorials, we conducted interviews with 20 undergraduate students. We present a key distinction between computational versus combinatorial conceptions, and we explore three aspects of data that shed light on students' conceptions (their initial characterizations, their definitions of 0!, and their responses to Likert-response questions). We present implications this may have for mathematics educators both within and separate from combinatorics.

Investigation of cadmium pollution in the spruce saplings near the metal production factory.

PubMed

Hashemi, Seyed Armin; Farajpour, Ghasem

2016-02-01

Toxic metals such as lead and cadmium are among the pollutants that are created by the metal production factories and disseminated in the nature. In order to study the quantity of cadmium pollution in the environment of the metal production factories, 50 saplings of the spruce species at the peripheries of the metal production factories were examined and the samples of the leaves, roots, and stems of saplings planted around the factory and the soil of the environment of the factory were studied to investigate pollution with cadmium. They were compared to the soil and saplings of the spruce trees planted outside the factory as observer region. The results showed that the quantity of pollution in the leaves, stems, and roots of the trees planted inside the factory environment were estimated at 1.1, 1.5, and 2.5 mg/kg, respectively, and this indicated a significant difference with the observer region (p < 0.05). The quantity of cadmium in the soil of the peripheries of the metal production factory was estimated at 6.8 mg/kg in the depth of 0-10 cm beneath the level of the soil. The length of roots in the saplings planted around the factory of metal production stood at 11 and 14.5 cm in the observer region which had a significant difference with the observer region (p < 0.05). The quantity of soil resources and spruce species' pollution with cadmium in the region has been influenced by the production processes in the factory. © The Author(s) 2013.

Factory-Calibrated Continuous Glucose Sensors: The Science Behind the Technology.

PubMed

Hoss, Udo; Budiman, Erwin Satrya

2017-05-01

The use of commercially available continuous glucose monitors for diabetes management requires sensor calibrations, which until recently are exclusively performed by the patient. A new development is the implementation of factory calibration for subcutaneous glucose sensors, which eliminates the need for user calibrations and the associated blood glucose tests. Factory calibration means that the calibration process is part of the sensor manufacturing process and performed under controlled laboratory conditions. The ability to move from a user calibration to factory calibration is based on several technical requirements related to sensor stability and the robustness of the sensor manufacturing process. The main advantages of factory calibration over the conventional user calibration are: (a) more convenience for the user, since no more fingersticks are required for calibration and (b) elimination of use errors related to the execution of the calibration process, which can lead to sensor inaccuracies. The FreeStyle Libre ™ and FreeStyle Libre Pro ™ flash continuous glucose monitoring systems are the first commercially available sensor systems using factory-calibrated sensors. For these sensor systems, no user calibrations are required throughout the sensor wear duration.

Factory-Calibrated Continuous Glucose Sensors: The Science Behind the Technology

PubMed Central

Budiman, Erwin Satrya

2017-01-01

Abstract The use of commercially available continuous glucose monitors for diabetes management requires sensor calibrations, which until recently are exclusively performed by the patient. A new development is the implementation of factory calibration for subcutaneous glucose sensors, which eliminates the need for user calibrations and the associated blood glucose tests. Factory calibration means that the calibration process is part of the sensor manufacturing process and performed under controlled laboratory conditions. The ability to move from a user calibration to factory calibration is based on several technical requirements related to sensor stability and the robustness of the sensor manufacturing process. The main advantages of factory calibration over the conventional user calibration are: (a) more convenience for the user, since no more fingersticks are required for calibration and (b) elimination of use errors related to the execution of the calibration process, which can lead to sensor inaccuracies. The FreeStyle Libre™ and FreeStyle Libre Pro™ flash continuous glucose monitoring systems are the first commercially available sensor systems using factory-calibrated sensors. For these sensor systems, no user calibrations are required throughout the sensor wear duration. PMID:28541139

Manufacturing data analytics using a virtual factory representation.

PubMed

Jain, Sanjay; Shao, Guodong; Shin, Seung-Jun

2017-01-01

Large manufacturers have been using simulation to support decision-making for design and production. However, with the advancement of technologies and the emergence of big data, simulation can be utilised to perform and support data analytics for associated performance gains. This requires not only significant model development expertise, but also huge data collection and analysis efforts. This paper presents an approach within the frameworks of Design Science Research Methodology and prototyping to address the challenge of increasing the use of modelling, simulation and data analytics in manufacturing via reduction of the development effort. The use of manufacturing simulation models is presented as data analytics applications themselves and for supporting other data analytics applications by serving as data generators and as a tool for validation. The virtual factory concept is presented as the vehicle for manufacturing modelling and simulation. Virtual factory goes beyond traditional simulation models of factories to include multi-resolution modelling capabilities and thus allowing analysis at varying levels of detail. A path is proposed for implementation of the virtual factory concept that builds on developments in technologies and standards. A virtual machine prototype is provided as a demonstration of the use of a virtual representation for manufacturing data analytics.

Multi-photon absorption limits to heralded single photon sources

PubMed Central

Husko, Chad A.; Clark, Alex S.; Collins, Matthew J.; De Rossi, Alfredo; Combrié, Sylvain; Lehoucq, Gaëlle; Rey, Isabella H.; Krauss, Thomas F.; Xiong, Chunle; Eggleton, Benjamin J.

2013-01-01

Single photons are of paramount importance to future quantum technologies, including quantum communication and computation. Nonlinear photonic devices using parametric processes offer a straightforward route to generating photons, however additional nonlinear processes may come into play and interfere with these sources. Here we analyse spontaneous four-wave mixing (SFWM) sources in the presence of multi-photon processes. We conduct experiments in silicon and gallium indium phosphide photonic crystal waveguides which display inherently different nonlinear absorption processes, namely two-photon (TPA) and three-photon absorption (ThPA), respectively. We develop a novel model capturing these diverse effects which is in excellent quantitative agreement with measurements of brightness, coincidence-to-accidental ratio (CAR) and second-order correlation function g(2)(0), showing that TPA imposes an intrinsic limit on heralded single photon sources. We build on these observations to devise a new metric, the quantum utility (QMU), enabling further optimisation of single photon sources. PMID:24186400

Non-Poissonian photon statistics from macroscopic photon cutting materials.

PubMed

de Jong, Mathijs; Meijerink, Andries; Rabouw, Freddy T

2017-05-24

In optical materials energy is usually extracted only from the lowest excited state, resulting in fundamental energy-efficiency limits such as the Shockley-Queisser limit for single-junction solar cells. Photon-cutting materials provide a way around such limits by absorbing high-energy photons and 'cutting' them into multiple low-energy excitations that can subsequently be extracted. The occurrence of photon cutting or quantum cutting has been demonstrated in a variety of materials, including semiconductor quantum dots, lanthanides and organic dyes. Here we show that photon cutting results in bunched photon emission on the timescale of the excited-state lifetime, even when observing a macroscopic number of optical centres. Our theoretical derivation matches well with experimental data on NaLaF 4 :Pr 3+ , a material that can cut deep-ultraviolet photons into two visible photons. This signature of photon cutting can be used to identify and characterize new photon-cutting materials unambiguously.

Students Tackle Academics in Practical Context at Skateboard Factory

ERIC Educational Resources Information Center

Pearson, George

2012-01-01

High school student Nick Robertson came to Oasis Skateboard Factory (OSF) from a suburban Toronto district. He was surfing the web when he spotted a reference to Oasis Skateboard Factory, an alternative program in the Toronto District School Board. He says his first reaction was "Skateboards in school? It didn't seem possible." He…

Deterministically swapping frequency-bin entanglement from photon-photon to atom-photon hybrid systems

NASA Astrophysics Data System (ADS)

Ou, Bao-Quan; Liu, Chang; Sun, Yuan; Chen, Ping-Xing

2018-02-01

Inspired by the recent developments of the research on the atom-photon quantum interface and energy-time entanglement between single-photon pulses, we are motivated to study the deterministic protocol for the frequency-bin entanglement of the atom-photon hybrid system, which is analogous to the frequency-bin entanglement between single-photon pulses. We show that such entanglement arises naturally in considering the interaction between a frequency-bin entangled single-photon pulse pair and a single atom coupled to an optical cavity, via straightforward atom-photon phase gate operations. Its anticipated properties and preliminary examples of its potential application in quantum networking are also demonstrated. Moreover, we construct a specific quantum entanglement witness tool to detect such extended frequency-bin entanglement from a reasonably general set of separable states, and prove its capability theoretically. We focus on the energy-time considerations throughout the analysis.

Neuromorphic photonic networks using silicon photonic weight banks.

PubMed

Tait, Alexander N; de Lima, Thomas Ferreira; Zhou, Ellen; Wu, Allie X; Nahmias, Mitchell A; Shastri, Bhavin J; Prucnal, Paul R

2017-08-07

Photonic systems for high-performance information processing have attracted renewed interest. Neuromorphic silicon photonics has the potential to integrate processing functions that vastly exceed the capabilities of electronics. We report first observations of a recurrent silicon photonic neural network, in which connections are configured by microring weight banks. A mathematical isomorphism between the silicon photonic circuit and a continuous neural network model is demonstrated through dynamical bifurcation analysis. Exploiting this isomorphism, a simulated 24-node silicon photonic neural network is programmed using "neural compiler" to solve a differential system emulation task. A 294-fold acceleration against a conventional benchmark is predicted. We also propose and derive power consumption analysis for modulator-class neurons that, as opposed to laser-class neurons, are compatible with silicon photonic platforms. At increased scale, Neuromorphic silicon photonics could access new regimes of ultrafast information processing for radio, control, and scientific computing.

1. FACTORY BUILDING VIEWED FROM THE EAST, CURING AND STORAGE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. FACTORY BUILDING VIEWED FROM THE EAST, CURING AND STORAGE WING TO THE LEFT, BOILING HOUSE IN THE CENTER, GRINDING PLATFORM TO THE FAR RIGHT, ST. THOMAS ISLAND VISIBLE IN BACKGROUND - Caneel Bay Plantation, Sugar Factory, Cruz Bay, St. John, VI

Analysis of replication factories in human cells by super-resolution light microscopy

PubMed Central

2009-01-01

Background DNA replication in human cells is performed in discrete sub-nuclear locations known as replication foci or factories. These factories form in the nucleus during S phase and are sites of DNA synthesis and high local concentrations of enzymes required for chromatin replication. Why these structures are required, and how they are organised internally has yet to be identified. It has been difficult to analyse the structure of these factories as they are small in size and thus below the resolution limit of the standard confocal microscope. We have used stimulated emission depletion (STED) microscopy, which improves on the resolving power of the confocal microscope, to probe the structure of these factories at sub-diffraction limit resolution. Results Using immunofluorescent imaging of PCNA (proliferating cell nuclear antigen) and RPA (replication protein A) we show that factories are smaller in size (approximately 150 nm diameter), and greater in number (up to 1400 in an early S- phase nucleus), than is determined by confocal imaging. The replication inhibitor hydroxyurea caused an approximately 40% reduction in number and a 30% increase in diameter of replication factories, changes that were not clearly identified by standard confocal imaging. Conclusions These measurements for replication factory size now approach the dimensions suggested by electron microscopy. This agreement between these two methods, that use very different sample preparation and imaging conditions, suggests that we have arrived at a true measurement for the size of these structures. The number of individual factories present in a single nucleus that we measure using this system is greater than has been previously reported. This analysis therefore suggests that each replication factory contains fewer active replication forks than previously envisaged. PMID:20015367

Rapid prototyping 3D virtual world interfaces within a virtual factory environment

NASA Technical Reports Server (NTRS)

Kosta, Charles Paul; Krolak, Patrick D.

1993-01-01

On-going work into user requirements analysis using CLIPS (NASA/JSC) expert systems as an intelligent event simulator has led to research into three-dimensional (3D) interfaces. Previous work involved CLIPS and two-dimensional (2D) models. Integral to this work was the development of the University of Massachusetts Lowell parallel version of CLIPS, called PCLIPS. This allowed us to create both a Software Bus and a group problem-solving environment for expert systems development. By shifting the PCLIPS paradigm to use the VEOS messaging protocol we have merged VEOS (HlTL/Seattle) and CLIPS into a distributed virtual worlds prototyping environment (VCLIPS). VCLIPS uses the VEOS protocol layer to allow multiple experts to cooperate on a single problem. We have begun to look at the control of a virtual factory. In the virtual factory there are actors and objects as found in our Lincoln Logs Factory of the Future project. In this artificial reality architecture there are three VCLIPS entities in action. One entity is responsible for display and user events in the 3D virtual world. Another is responsible for either simulating the virtual factory or communicating with the real factory. The third is a user interface expert. The interface expert maps user input levels, within the current prototype, to control information for the factory. The interface to the virtual factory is based on a camera paradigm. The graphics subsystem generates camera views of the factory on standard X-Window displays. The camera allows for view control and object control. Control or the factory is accomplished by the user reaching into the camera views to perform object interactions. All communication between the separate CLIPS expert systems is done through VEOS.

Development of muon ring coolers, neutrino factories and supersymmetric Higgs factory

NASA Astrophysics Data System (ADS)

Cline, David B.

2003-08-01

Over the past few years or so a key new development is the invention of ring coolers for muon cooling. In particular, these rings demonstrate robust cooling of the longitudinal phase space. We discuss the quadrupole or UCLA ring cooler and the prospects to make this a final cooler to reduce the transceiver emittance to the value required for a mu+mu- collider. This will lead to a Higgs factory for the A0/H0 in supersymmetry models.

Development of Muon Ring Coolers, Neutrino Factories and Supersymmetric Higgs Factory

NASA Astrophysics Data System (ADS)

Cline, David B.

2002-12-01

Over the past few years or so a key new development is the invention of Ring Coolers for muon cooling. In particular these rings demonstrate robust cooling of the longitudinal phase space. We discuss the Quadrupole or UCLA Ring Cooler and the prospects to make this a final cooler to reduce the tranceiver emittance to the value required for a μ+ μ- collider. This will lead to a Higgs Factory for the A0/H0 in supersymmetry models.

Baby Factories in Nigeria: Starting the Discussion Toward a National Prevention Policy.

PubMed

Makinde, Olusesan Ayodeji; Olaleye, Olalekan; Makinde, Olufunmbi Olukemi; Huntley, Svetlana S; Brown, Brandon

2017-01-01

Baby factories and baby harvesting are relatively new terms that involve breeding, trafficking, and abuse of infants and their biological mothers. Since it was first described in a United Nations Educational, Scientific and Cultural Organization report in Nigeria in 2006, several more baby factories have been discovered over the years. Infertile women are noted to be major patrons of these baby factories due to the stigmatization of childless couples in Southern Nigeria and issues around cultural acceptability of surrogacy and adoption. These practices have contributed to the growth in the industry which results in physical, psychological, and sexual violence to the victims. Tackling baby factories will involve a multifaceted approach that includes advocacy and enacting of legislation barring baby factories and infant trafficking and harsh consequences for their patrons. Also, programs to educate young girls on preventing unwanted pregnancies are needed. Methods of improving awareness and acceptability of adoption and surrogacy and reducing the administrative and legal bottlenecks associated with these options for infertile couples should be explored to diminish the importance of baby factories. © The Author(s) 2015.

Factorial Structure of the New Ecological Paradigm Scale in Two French Samples

ERIC Educational Resources Information Center

Fleury-Bahi, Ghozlane; Marcouyeux, Aurore; Renard, Elise; Roussiau, Nicolas

2015-01-01

The principal objective of this research is to test the factorial structure of the New Ecological Paradigm scale on a population of men and women residing in France. The tested model is a second-order factorial model. This factorial structure is evaluated on two separate samples to test the stability of the solution (a first sample of 253…

B factory plans at Cornell

NASA Astrophysics Data System (ADS)

Berkelman, Karl

1989-12-01

Recent upgrade project at the Cornell Electron Storage Ring is discussed. Modification was made to make B mesons factory design possible. The CLEO detector has been rebuilt with a new superconducting magnet and a high resolution electromagnetic calorimeter made of cesium iodide scintillators.(AIP)

Pion Production for Neutrino Factory-challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Breton, Florian; Le Couedic, Clement; Soler, F. J. P.

2011-10-06

One of the key issues in the design of a Neutrino Factory target station is the determination of the optimum kinetic energy of the proton beam due to the large uncertainties in simulations of protons impinging on nuclear targets. In this paper we have developed a procedure to correct GEANT4 simulations for the HARP data, and we have determined the yield of muons expected at the front-end of a Neutrino Factory as a function of target material (Be, C, Al, Ta and Pb) and energy (3-12 GeV).The maximum muon yield is found between 5 and 8 GeV for high Zmore » targets and 3 GeV for low Z targets.« less

Two-photon spectroscopy of excitons with entangled photons.

PubMed

Schlawin, Frank; Mukamel, Shaul

2013-12-28

The utility of quantum light as a spectroscopic tool is demonstrated for frequency-dispersed pump-probe, integrated pump-probe, and two-photon fluorescence signals which show Ramsey fringes. Simulations of the frequency-dispersed transmission of a broadband pulse of entangled photons interacting with a three-level model of matter reveal how the non-classical time-bandwidth properties of entangled photons can be used to disentangle congested spectra, and reveal otherwise unresolved features. Quantum light effects are most pronounced at weak intensities when entangled photon pairs are well separated, and are gradually diminished at higher intensities when different photon pairs overlap.

Two-photon spectroscopy of excitons with entangled photons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schlawin, Frank, E-mail: Frank.Schlawin@physik.uni-freiburg.de; Physikalisches Institut, Albert-Ludwigs-Universität Freiburg, Hermann-Herder-Straße 3, 79108 Freiburg; Mukamel, Shaul, E-mail: smukamel@uci.edu

The utility of quantum light as a spectroscopic tool is demonstrated for frequency-dispersed pump-probe, integrated pump-probe, and two-photon fluorescence signals which show Ramsey fringes. Simulations of the frequency-dispersed transmission of a broadband pulse of entangled photons interacting with a three-level model of matter reveal how the non-classical time-bandwidth properties of entangled photons can be used to disentangle congested spectra, and reveal otherwise unresolved features. Quantum light effects are most pronounced at weak intensities when entangled photon pairs are well separated, and are gradually diminished at higher intensities when different photon pairs overlap.

Approaching the socialist factory and its workforce: considerations from fieldwork in (former) Yugoslavia

PubMed Central

Archer, Rory; Musić, Goran

2017-01-01

Abstract The socialist factory, as the ‘incubator’ of the new socialist (wo)man, is a productive entry point for the study of socialist modernization and its contradictions. By outlining some theoretical and methodological insights gathered through field-research in factories in former Yugoslavia, we seek to connect the state of labour history in the Balkans to recent breakthroughs made by labour historians of other socialist countries. The first part of this article sketches some of the specificities of the Yugoslav self-managed factory and its heterogeneous workforce. It presents the ambiguous relationship between workers and the factory and demonstrates the variety of life trajectories for workers in Yugoslav state-socialism (from model communists to alienated workers). The second part engages with the available sources for conducting research inside and outside the factory advocating an approach which combines factory and local archives, print media and oral history. PMID:28190894

Approaching the socialist factory and its workforce: considerations from fieldwork in (former) Yugoslavia.

PubMed

Archer, Rory; Musić, Goran

2017-01-01

The socialist factory, as the 'incubator' of the new socialist (wo)man, is a productive entry point for the study of socialist modernization and its contradictions. By outlining some theoretical and methodological insights gathered through field-research in factories in former Yugoslavia, we seek to connect the state of labour history in the Balkans to recent breakthroughs made by labour historians of other socialist countries. The first part of this article sketches some of the specificities of the Yugoslav self-managed factory and its heterogeneous workforce. It presents the ambiguous relationship between workers and the factory and demonstrates the variety of life trajectories for workers in Yugoslav state-socialism (from model communists to alienated workers). The second part engages with the available sources for conducting research inside and outside the factory advocating an approach which combines factory and local archives, print media and oral history.

Modeling the spectral response for the soft X-ray imager onboard the ASTRO-H satellite

NASA Astrophysics Data System (ADS)

Inoue, Shota; Hayashida, Kiyoshi; Katada, Shuhei; Nakajima, Hiroshi; Nagino, Ryo; Anabuki, Naohisa; Tsunemi, Hiroshi; Tsuru, Takeshi Go; Tanaka, Takaaki; Uchida, Hiroyuki; Nobukawa, Masayoshi; Nobukawa, Kumiko Kawabata; Washino, Ryosaku; Mori, Koji; Isoda, Eri; Sakata, Miho; Kohmura, Takayoshi; Tamasawa, Koki; Tanno, Shoma; Yoshino, Yuma; Konno, Takahiro; Ueda, Shutaro; ASTRO-H/SXI Team

2016-09-01

The ASTRO-H satellite is the 6th Japanese X-ray astronomical observatory to be launched in early 2016. The satellite carries four kinds of detectors, and one of them is an X-ray CCD camera, the soft X-ray imager (SXI), installed on the focal plane of an X-ray telescope. The SXI contains four CCD chips, each with an imaging area of 31 mm × 31 mm , arrayed in mosaic, covering the field-of-view of 38‧ ×38‧ , the widest ever flown in orbit. The CCDs are a P-channel back-illuminated (BI) type with a depletion layer thickness of 200 μ m . We operate the CCDs in a photon counting mode in which the position and energy of each photon are measured in the energy band of 0.4-12 keV. To evaluate the X-ray spectra obtained with the SXI, an accurate calibration of its response function is essential. For this purpose, we performed calibration experiments at Kyoto and Photon Factory of KEK, each with different X-ray sources with various X-ray energies. We fit the obtained spectra with 5 components; primary peak, secondary peak, constant tail, Si escape and Si fluorescence, and then model their energy dependence using physics-based or empirical formulae. Since this is the first adoption of P-channel BI-type CCDs on an X-ray astronomical satellite, we need to take special care on the constant tail component which is originated in partial charge collection. It is found that we need to assume a trapping layer at the incident surface of the CCD and implement it in the response model. In addition, the Si fluorescence component of the SXI response is significantly weak, compared with those of front-illuminated type CCDs.

"Mixing" as an ethnoetiology of HIV/AIDS in Malaysia's multinational factories.

PubMed

Root, Robin

2006-09-01

Minah Karan, the stigmatizing label appended to Malay factory women in the 1980s, signaled a dangerous female sexuality that risked spreading beyond the factory gates and infecting Malaysia's idea(l)s of its traditional kampung culture. This article narrates how Minah Karan, as the former antihero of development, was reconstituted in the 1990s, with the government's labeling of factories as "high-risk settings" for HIV/AIDS. This is an ethnoetiology based not on any evidential epidemiological data but on the racial and gendered "mixing" that transpires behind factory walls: a fear that the "mixing of the sexes" means ipso facto "sexual mixing" among the races. The article demonstrates how importation of the high-risk label articulates at the local level the new and contested linkages, economic, religious, and scientific, constitutive of globalization. The pragmatic nature and imperatives of this high-risk process are discerned in factory women's accounts of how they negotiate the interactional imperatives of factory work, because transnational structures of productivity violate the social boundaries that have long connoted political stability, moral integrity, ethnic community, and individual safety. The article concludes by questioning whether ethnoetiologies, especially when they concern sexual networks, become social etiologies, because this would locate ethnoetiologies as central to conventional public health praxis rather than as ethnographic exotica in the margins.

Neutrino Factory Plans at CERN

NASA Astrophysics Data System (ADS)

Riche, J. A.

2002-10-01

The considerable interest raised by the discovery of neutrino oscillations and recent progress in studies of muon colliders has triggered interest in considering a neutrino factory at CERN. This paper explains the reference scenario, indicates the other possible choices and mentions the R&D that are foreseen.

gPhoton: The GALEX Photon Data Archive

NASA Astrophysics Data System (ADS)

Million, Chase; Fleming, Scott W.; Shiao, Bernie; Seibert, Mark; Loyd, Parke; Tucker, Michael; Smith, Myron; Thompson, Randy; White, Richard L.

2016-12-01

gPhoton is a new database product and software package that enables analysis of GALEX ultraviolet data at the photon level. The project’s stand-alone, pure-Python calibration pipeline reproduces the functionality of the original mission pipeline to reduce raw spacecraft data to lists of time-tagged, sky-projected photons, which are then hosted in a publicly available database by the Mikulski Archive at Space Telescope. This database contains approximately 130 terabytes of data describing approximately 1.1 trillion sky-projected events with a timestamp resolution of five milliseconds. A handful of Python and command-line modules serve as a front end to interact with the database and to generate calibrated light curves and images from the photon-level data at user-defined temporal and spatial scales. The gPhoton software and source code are in active development and publicly available under a permissive license. We describe the motivation, design, and implementation of the calibration pipeline, database, and tools, with emphasis on divergence from prior work, as well as challenges created by the large data volume. We summarize the astrometric and photometric performance of gPhoton relative to the original mission pipeline. For a brief example of short time-domain science capabilities enabled by gPhoton, we show new flares from the known M-dwarf flare star CR Draconis. The gPhoton software has permanent object identifiers with the ASCL (ascl:1603.004) and DOI (doi:10.17909/T9CC7G). This paper describes the software as of version v1.27.2.

gPhoton: THE GALEX PHOTON DATA ARCHIVE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Million, Chase; Fleming, Scott W.; Shiao, Bernie

gPhoton is a new database product and software package that enables analysis of GALEX ultraviolet data at the photon level. The project’s stand-alone, pure-Python calibration pipeline reproduces the functionality of the original mission pipeline to reduce raw spacecraft data to lists of time-tagged, sky-projected photons, which are then hosted in a publicly available database by the Mikulski Archive at Space Telescope. This database contains approximately 130 terabytes of data describing approximately 1.1 trillion sky-projected events with a timestamp resolution of five milliseconds. A handful of Python and command-line modules serve as a front end to interact with the database andmore » to generate calibrated light curves and images from the photon-level data at user-defined temporal and spatial scales. The gPhoton software and source code are in active development and publicly available under a permissive license. We describe the motivation, design, and implementation of the calibration pipeline, database, and tools, with emphasis on divergence from prior work, as well as challenges created by the large data volume. We summarize the astrometric and photometric performance of gPhoton relative to the original mission pipeline. For a brief example of short time-domain science capabilities enabled by gPhoton, we show new flares from the known M-dwarf flare star CR Draconis. The gPhoton software has permanent object identifiers with the ASCL (ascl:1603.004) and DOI (doi:10.17909/T9CC7G). This paper describes the software as of version v1.27.2.« less

Photonic Bandgaps in Photonic Molecules

NASA Technical Reports Server (NTRS)

Smith, David D.; Chang, Hongrok; Gates, Amanda L.; Fuller, Kirk A.; Gregory, Don A.; Witherow, William K.; Paley, Mark S.; Frazier, Donald O.; Curreri, Peter A. (Technical Monitor)

2002-01-01

This talk will focus on photonic bandgaps that arise due to nearly free photon and tight-binding effects in coupled microparticle and ring-resonator systems. The Mie formulation for homogeneous spheres is generalized to handle core/shell systems and multiple concentric layers in a manner that exploits an analogy with stratified planar systems, thereby allowing concentric multi-layered structures to be treated as photonic bandgap (PBG) materials. Representative results from a Mie code employing this analogy demonstrate that photonic bands arising from nearly free photon effects are easily observed in the backscattering, asymmetry parameter, and albedo for periodic quarter-wave concentric layers, though are not readily apparent in extinction spectra. Rather, the periodicity simply alters the scattering profile, enhancing the ratio of backscattering to forward scattering inside the bandgap, in direct analogy with planar quarter-wave multilayers. PBGs arising from tight-binding may also be observed when the layers (or rings) are designed such that the coupling between them is weak. We demonstrate that for a structure consisting of N coupled micro-resonators, the morphology dependent resonances split into N higher-Q modes, in direct analogy with other types of oscillators, and that this splitting ultimately results in PBGs which can lead to enhanced nonlinear optical effects.

Kinetic models in industrial biotechnology - Improving cell factory performance.

PubMed

Almquist, Joachim; Cvijovic, Marija; Hatzimanikatis, Vassily; Nielsen, Jens; Jirstrand, Mats

2014-07-01

An increasing number of industrial bioprocesses capitalize on living cells by using them as cell factories that convert sugars into chemicals. These processes range from the production of bulk chemicals in yeasts and bacteria to the synthesis of therapeutic proteins in mammalian cell lines. One of the tools in the continuous search for improved performance of such production systems is the development and application of mathematical models. To be of value for industrial biotechnology, mathematical models should be able to assist in the rational design of cell factory properties or in the production processes in which they are utilized. Kinetic models are particularly suitable towards this end because they are capable of representing the complex biochemistry of cells in a more complete way compared to most other types of models. They can, at least in principle, be used to in detail understand, predict, and evaluate the effects of adding, removing, or modifying molecular components of a cell factory and for supporting the design of the bioreactor or fermentation process. However, several challenges still remain before kinetic modeling will reach the degree of maturity required for routine application in industry. Here we review the current status of kinetic cell factory modeling. Emphasis is on modeling methodology concepts, including model network structure, kinetic rate expressions, parameter estimation, optimization methods, identifiability analysis, model reduction, and model validation, but several applications of kinetic models for the improvement of cell factories are also discussed. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Organic Aggregates with (delta)D and delta(sup 15)N Anomalies in the Zag Clast Revealed by STXM and NanoSIMS

NASA Technical Reports Server (NTRS)

Kebukawa, Y.; Ito, M.; Zolensky, M. E.; Rahman, Z.; Kilcoyne, A. L. D.; Nakato, A.; Takeichi, Y.; Suga, H.; Miyamoto, C.; Mase, K.;

Construction and performance of BL28 of the Photon Factory for circularly polarized synchrotron radiation

NASA Astrophysics Data System (ADS)

Kagoshima, Yasushi; Muto, Sadatsugu; Miyahara, Tsuneaki; Koide, Tsuneharu; Yamamoto, Shigeru; Kitamura, Hideo

1992-01-01

A branch beamline, BL28A, has been constructed for the application of circularly polarized vacuum ultraviolet radiation. The radiation can be obtained in the helical undulator operation mode of an insertion device, EMPW♯28, which is also cut for elliptically polarized hard x-ray radiation. T first harmonic of the helical undulator radiation can be tuned from 40 to 350 eV with its corresponding K value from 3 to 0.2. A monochromator working basically with constant deviation optics was installed, and has started its operation. A circularly polarized flux of ˜1010 photons/s has been achieved with energy resolution of around 500-1000 at the first harmonic peak. The circular polarization after the monochromator was estimated to be higher than 70% by comparing theory and experiment on the magnetic circular dichroism of nickel films in the 3p-3d excitation region. The design philosophy of the beamline and recent results on the performance tests are presented.

Two-photon interference of polarization-entangled photons in a Franson interferometer.

PubMed

Kim, Heonoh; Lee, Sang Min; Kwon, Osung; Moon, Han Seb

2017-07-18

We present two-photon interference experiments with polarization-entangled photon pairs in a polarization-based Franson-type interferometer. Although the two photons do not meet at a common beamsplitter, a phase-insensitive Hong-Ou-Mandel type two-photon interference peak and dip fringes are observed, resulting from the two-photon interference effect between two indistinguishable two-photon probability amplitudes leading to a coincidence detection. A spatial quantum beating fringe is also measured for nondegenerate photon pairs in the same interferometer, although the two-photon states have no frequency entanglement. When unentangled polarization-correlated photons are used as an input state, the polarization entanglement is successfully recovered through the interferometer via delayed compensation.

The Skateboard Factory: Curriculum by Design--Oasis Skateboard Factory Q&A with Craig Morrison

ERIC Educational Resources Information Center

Pearson, George

2012-01-01

Since its opening three years ago, Oasis Skateboard Factory (OSF), founded by teacher Craig Morrison, has attracted considerable media exposure and received a Ken Spencer Award from the CEA for its innovative program. OSF is one of three programs offered by Oasis Alternative Secondary School, one of 22 alternative secondary schools of the Toronto…

Aft segment dome-to-stiffener factory joint insulation void elimination

NASA Technical Reports Server (NTRS)

Jensen, S. K.

1991-01-01

Since the detection of voids in the internal insulation of the dome-to-stiffener factory joint of the 15B aft segment, all aft segment dome-to-stiffener factory joints were x-rated and all were found to contain voids. Using a full-scale process simulation article (PSA), the objective was to demonstrate that the proposed changes in the insulation layup and vacuum bagging processes will greatly reduce or eliminate voids without adversely affecting the configuration of performance of the insulation which serves as a primary seal over the factory joint. The PSA-8 aft segment was insulated and cured using standard production processes.

Effect of factory effluents on physiological and biochemical contents of Gossypium hirsutum l.

PubMed

Muthusamy, A; Jayabalan, N

2001-10-01

The effect of sago and sugar factory effluents was studied on Gossypium hirsutum L. var. MCU 5 and MCU 11. Plants were irrigated with 0, 25, 50, 75 and 100% of effluents of both factories. At lower concentration (25%) of sugar factory effluents had stimulatory effect on all biochemical contents observed. Moreover, all concentration of sago factory effluents were found to have inhibitory effect on all biochemical contents except proline content which increased with increasing concentration of both the effluents. Plants growing on adjacent to sago and sugar factories or they irrigated with such type of polluted water, may accumulate the heavy metals found in both the effluents, at higher levels in plant products and if consumed may have similar effect on living organisms.

Photonic time crystals.

PubMed

Zeng, Lunwu; Xu, Jin; Wang, Chengen; Zhang, Jianhua; Zhao, Yuting; Zeng, Jing; Song, Runxia

2017-12-07

When space (time) translation symmetry is spontaneously broken, the space crystal (time crystal) forms; when permittivity and permeability periodically vary with space (time), the photonic crystal (photonic time crystal) forms. We proposed the concept of photonic time crystal and rewritten the Maxwell's equations. Utilizing Finite Difference Time Domain (FDTD) method, we simulated electromagnetic wave propagation in photonic time crystal and photonic space-time crystal, the simulation results show that more intensive scatter fields can obtained in photonic time crystal and photonic space-time crystal.

37. NORTH TO BINS ALONG NORTH WALL OF FACTORY BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. NORTH TO BINS ALONG NORTH WALL OF FACTORY BUILDING WHICH REMAIN FILLED WITH NEW OLD STOCK AND USED PARTS FOR ELI WINDMILLS. THE ROPE AT THE LOWER FOREGROUND WAS USED IN ERECTING WINDMILLS AND TOWERS FOR CUSTOMERS. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

Epidemiology of Skin Disease in an Automobile Factory*

PubMed Central

Newhouse, Muriel L.

1964-01-01

A survey was made of a random sample of workers from the machine shops, assembly lines, and stock and store departments of an automobile factory. Among the 1,223 men seen, representing 97% of the sample, the prevalence of non-infective skin diseases was 14·5%. Skin diseases were classified into four groups: `dermatitis' and `folliculitis' of occupational origin, endogenous `eczemas', and miscellaneous skin diseases. Slightly more than half of all the skin diseases seen were considered to be occupational in origin. In this population the prevalence of skin disease was more than four times that based on patients attending the factory medical department. An unsuspected cause of allergic dermatitis was found on the assembly lines, where the incidence of dermatitis was significantly higher than among the non-production workers. The prevalence of folliculitis was significantly higher among production than non-production workers. There was no significant difference in the prevalence of `eczema' or the miscellaneous skin diseases in the various occupational groups. Among European workers fair men were more prone to skin disease than darker men. In another factory, a West Indian and Asiatic group of workers had a significantly lower prevalence of skin diseases than a group of Europeans doing similar work. Folliculitis was more prevalent among the younger workers and those recently employed in the factory; there was no obvious association between age and length of service and the occurrence of other types of skin disease. PMID:14249898

An examination of effect estimation in factorial and standardly-tailored designs

PubMed Central

Allore, Heather G; Murphy, Terrence E

2012-01-01

Background Many clinical trials are designed to test an intervention arm against a control arm wherein all subjects are equally eligible for all interventional components. Factorial designs have extended this to test multiple intervention components and their interactions. A newer design referred to as a ‘standardly-tailored’ design, is a multicomponent interventional trial that applies individual interventional components to modify risk factors identified a priori and tests whether health outcomes differ between treatment arms. Standardly-tailored designs do not require that all subjects be eligible for every interventional component. Although standardly-tailored designs yield an estimate for the net effect of the multicomponent intervention, it has not yet been shown if they permit separate, unbiased estimation of individual component effects. The ability to estimate the most potent interventional components has direct bearing on conducting second stage translational research. Purpose We present statistical issues related to the estimation of individual component effects in trials of geriatric conditions using factorial and standardly-tailored designs. The medical community is interested in second stage translational research involving the transfer of results from a randomized clinical trial to a community setting. Before such research is undertaken, main effects and synergistic and or antagonistic interactions between them should be identified. Knowledge of the relative strength and direction of the effects of the individual components and their interactions facilitates the successful transfer of clinically significant findings and may potentially reduce the number of interventional components needed. Therefore the current inability of the standardly-tailored design to provide unbiased estimates of individual interventional components is a serious limitation in their applicability to second stage translational research. Methods We discuss estimation of

[The professional responsibility of the factory physician].

PubMed

Tavani, M

1987-01-01

The author briefly reviews the present trends in jurisprudence concerning the professional liability of the physician in penal and civil law and, in the light of the much discussed decree issued by the Court of Cassation (Court of Appeal) (Decree No. 2799/86 - Labour Section), discusses the juridical position of the factory doctor, the juridical relationship between the doctor and the workforce, his contractual obligations, his rôle and his duties. The aspects that are more specifically appropriate to assessment of the professional liability of the factory doctor are described, commenting on the various criteria that may justify, in matters other than industrial accidents, recognition of the existence of an occupational disease.

A Profile-Based Framework for Factorial Similarity and the Congruence Coefficient.

PubMed

Hartley, Anselma G; Furr, R Michael

2017-01-01

We present a novel profile-based framework for understanding factorial similarity in the context of exploratory factor analysis in general, and for understanding the congruence coefficient (a commonly used index of factor similarity) specifically. First, we introduce the profile-based framework articulating factorial similarity in terms of 3 intuitive components: general saturation similarity, differential saturation similarity, and configural similarity. We then articulate the congruence coefficient in terms of these components, along with 2 additional profile-based components, and we explain how these components resolve ambiguities that can be-and are-found when using the congruence coefficient. Finally, we present secondary analyses revealing that profile-based components of factorial are indeed linked to experts' actual evaluations of factorial similarity. Overall, the profile-based approach we present offers new insights into the ways in which researchers can examine factor similarity and holds the potential to enhance researchers' ability to understand the congruence coefficient.

From gene to structure: The protein factory of the NBICS Centre of Kurchatov Institute

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyko, K. M.; Lipkin, A. V.; Popov, V. O., E-mail: vpopov@inbi.ras.ru

2013-05-15

The Protein Factory was established at the Centre for Nano, Bio, Info, Cognitive, and Social Sciences and Technologies (NBICS Centre) of the National Research Centre 'Kurchatov Institute' in 2010. The Protein Factory, together with the Centre for Synchrotron Radiation and Nanotechnology, promote research on structural biology. This paper presents the technology platforms developed at the Protein Factory and the facilities available for researchers. The main projects currently being performed at the Protein Factory are briefly described.

Resonant photonic States in coupled heterostructure photonic crystal waveguides.

PubMed

Cox, Jd; Sabarinathan, J; Singh, Mr

2010-02-09

In this paper, we study the photonic resonance states and transmission spectra of coupled waveguides made from heterostructure photonic crystals. We consider photonic crystal waveguides made from three photonic crystals A, B and C, where the waveguide heterostructure is denoted as B/A/C/A/B. Due to the band structure engineering, light is confined within crystal A, which thus act as waveguides. Here, photonic crystal C is taken as a nonlinear photonic crystal, which has a band gap that may be modified by applying a pump laser. We have found that the number of bound states within the waveguides depends on the width and well depth of photonic crystal A. It has also been found that when both waveguides are far away from each other, the energies of bound photons in each of the waveguides are degenerate. However, when they are brought close to each other, the degeneracy of the bound states is removed due to the coupling between them, which causes these states to split into pairs. We have also investigated the effect of the pump field on photonic crystal C. We have shown that by applying a pump field, the system may be switched between a double waveguide to a single waveguide, which effectively turns on or off the coupling between degenerate states. This reveals interesting results that can be applied to develop new types of nanophotonic devices such as nano-switches and nano-transistors.

Exposing the dark sector with future Z factories

NASA Astrophysics Data System (ADS)

Liu, Jia; Wang, Lian-Tao; Wang, Xiao-Ping; Xue, Wei

2018-05-01

We investigate the prospects of searching dark sector models via exotic Z -boson decay at future e+e- colliders with Giga Z and Tera Z options. Four general categories of dark sector models, Higgs portal dark matter, vector-portal dark matter, inelastic dark matter, and axionlike particles, are considered. Focusing on channels motivated by the dark sector models, we carry out a model-independent study of the sensitivities of Z factories in probing exotic decays. The limits on branching ratios of the exotic Z decay are typically O (10-6- 10-8.5) for the Giga Z and O (10-7.5- 10-11) for the Tera Z , and they are compared with the projection for the high luminosity LHC. We demonstrate that future Z factories can provide its unique and leading sensitivity and highlight the complementarity with other experiments, including the indirect and direct dark matter search limits and the existing collider limits. Future Z factories will play a leading role in uncovering the hidden sector of the Universe in the future.

Design Learning of Teaching Factory in Mechanical Engineering

NASA Astrophysics Data System (ADS)

Putra, R. C.; Kusumah, I. H.; Komaro, M.; Rahayu, Y.; Asfiyanur, E. P.

2018-02-01

The industrial world that is the target of the process and learning outcomes of vocational high school (SMK) has its own character and nuance. Therefore, vocational education institutions in the learning process should be able to make the appropriate learning approach and in accordance with the industrial world. One approach to learning that is based on production and learning in the world of work is by industry-based learning or known as Teaching Factory, where in this model apply learning that involves direct students in goods or service activities are expected to have the quality so it is worth selling and accepted by consumers. The method used is descriptive approach. The purpose of this research is to get the design of the teaching factory based on the competency requirements of the graduates of the spouse industry, especially in the engineering department. The results of this study is expected to be one of the choice of model factory teaching in the field of machinery engineering in accordance with the products and competencies of the graduates that the industry needs.

Development of the ARICH monitor system for the Belle II experiment

NASA Astrophysics Data System (ADS)

Hataya, K.; Adachi, I.; Dolenec, R.; Iori, S.; Iwata, S.; Kakuno, H.; Kataura, R.; Kawai, H.; Kindo, H.; Kobayashi, T.; Korpar, S.; Križan, P.; Kumita, T.; Mrvar, M.; Nishida, S.; Ogawa, K.; Ogawa, S.; Pestotnik, R.; Šantelj, L.; Sumiyoshi, T.; Tabata, M.; Yonenaga, M.; Yusa, Y.

2017-12-01

The Belle II detector is under construction at KEK in Japan. In the forward endcap region of the Belle II detector, particle identification (PID) is performed by the Aerogel Ring Imaging Cherenkov (ARICH) counter composed of aerogel tiles and 144-channel Hybrid Avalanche Photo-Detectors (HAPDs). The photon detection efficiency of the photosensor is important for a stable operation of the ARICH. To examine the performance of the HAPDs periodically, a monitor system using scattered photons injected by optical fibers is being developed. In this paper, we report the test using the prototype monitor system and the tests with a partially built ARICH detector.

Virtual Factory Framework for Supporting Production Planning and Control.

PubMed

Kibira, Deogratias; Shao, Guodong

2017-01-01

Developing optimal production plans for smart manufacturing systems is challenging because shop floor events change dynamically. A virtual factory incorporating engineering tools, simulation, and optimization generates and communicates performance data to guide wise decision making for different control levels. This paper describes such a platform specifically for production planning. We also discuss verification and validation of the constituent models. A case study of a machine shop is used to demonstrate data generation for production planning in a virtual factory.

Industrial Technology Modernization Program. Project 32. Factory Vision. Phase 2

DTIC Science & Technology

1988-04-01

instructions for the PWA’s, generating the numerical control (NC) program instructions for factory assembly equipment, controlling the process... generating the numerical control (NC) program instructions for factory assembly equipment, controlling the production process instructions and NC... Assembly Operations the "Create Production Process Program" will automatically generate a sequence of graphics pages (in paper mode), or graphics screens

A Survey of the Medical Needs of a Group of Small Factories*

PubMed Central

Lee, W. R.

1962-01-01

The present interest in medical services for small factories is matched by the limited objective information which is available on the demand for and needs of such services. As a teaching project, a survey was made of factories with between 30 and 200 employees on an estate in the North West where there was no organized medical service. Unfortunately, time allowed only 22 factories to be visited. The findings, therefore, are regarded as indicative rather than conclusive, but this does not detract from their interest. Factories were visited by two or three postgraduate students who completed a questionnaire designed to standardize their findings. The questionnaire is included as an appendix to this paper. Regarding the demand for medical services, four of the 22 factories were subsidiaries of larger organizations and had part-time medical advice, 14 expressed no interest even if this would have involved no financial commitment, and the remaining four were interested for differing reasons. The needs of the factories in this context were found to be, first, advice and perhaps better supervision of non-mechanical hazards and, secondly, supervision of the first aid arrangements. From the ambulance journey records of the local authority there appeared to be no great demand for local casualty facilities. To meet these needs it is suggested that the functions of the appointed factory doctor might be modified to include wider supervision of non-mechanical hazards and supervision of first aid arrangements. It is also suggested that the National Health Service should form the basis for dealing with those cases requiring more than first aid. PMID:14463582

Factorial versus Typological Models: A Comparison of Methods for Personality Data

ERIC Educational Resources Information Center

von Davier, Matthias; Naemi, Bobby; Roberts, Richard D.

2012-01-01

This article describes an exploration of the distinction between typological and factorial latent variables in the domain of personality theory. Traditionally, many personality variables have been considered to be factorial in nature, even though there are examples of typological constructs dating back to Hippocrates. Recently, some…

Tracing the contamination origin of coliform bacteria in two small food-processing factories.

PubMed

Tominaga, Tatsuya; Sekine, Masahiro; Oyaizu, Hiroshi

2008-09-01

The objective of this study was to trace contamination sources of coliform bacteria by comparing the types of coliforms between food samples and the processing environments in two small food-processing factories (factories A and B). Fermentation tests of five sugars enabled the successful classification of 16 representative type strains into eight distinct groups. The grouping procedure was then applied to comparison of the coliform flora between food products and various locations in their processing environments. The consistency between each food and the tested locations was evaluated using the Jaccard index. The air conditioner and refrigeration room floor in factory A showed an index of 1.00, while the shaping machine in factory B showed an index of 0.98, indicating that these locations could be contamination sources. The validity of our results was confirmed by randomly amplified polymorphic DNA, which showed 100% matched profiles between the air conditioner and the food in factory A, and highly matched profiles between the machine and the food in factory B. This method for comparing the coliform flora between food and environments has the potential to be a reliable tracing tool for various food industries.

Manipulation of photons at the surface of three-dimensional photonic crystals.

PubMed

Ishizaki, Kenji; Noda, Susumu

2009-07-16

In three-dimensional (3D) photonic crystals, refractive-index variations with a periodicity comparable to the wavelength of the light passing through the crystal give rise to so-called photonic bandgaps, which are analogous to electronic bandgaps for electrons moving in the periodic electrostatic potential of a material's crystal structure. Such 3D photonic bandgap crystals are envisioned to become fundamental building blocks for the control and manipulation of photons in optical circuits. So far, such schemes have been pursued by embedding artificial defects and light emitters inside the crystals, making use of 3D bandgap directional effects. Here we show experimentally that photons can be controlled and manipulated even at the 'surface' of 3D photonic crystals, where 3D periodicity is terminated, establishing a new and versatile route for photon manipulation. By making use of an evanescent-mode coupling technique, we demonstrate that 3D photonic crystals possess two-dimensional surface states, and we map their band structure. We show that photons can be confined and propagate through these two-dimensional surface states, and we realize their localization at arbitrary surface points by designing artificial surface-defect structures through the formation of a surface-mode gap. Surprisingly, the quality factors of the surface-defect mode are the largest reported for 3D photonic crystal nanocavities (Q up to approximately 9,000). In addition to providing a new approach for photon manipulation by photonic crystals, our findings are relevant for the generation and control of plasmon-polaritons in metals and the related surface photon physics. The absorption-free nature of the 3D photonic crystal surface may enable new sensing applications and provide routes for the realization of efficient light-matter interactions.

n-Hexane polyneuropathy in a ball-manufacturing factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, C.C.; Shih, T.S.; Cheng, S.Y.

Five overt and two occult cases of n-hexane polyneuropathy occurred in a ball-manufacturing factory in Taiwan. The severity of polyneuropathy was directly related to the index of n-hexane exposure that occurred during the processes of cement coating and nylon fiber winding in a poorly ventilated room. The n-hexane concentrations over eight hours of personal sampling of the air of the cement coating and nylon fiber winding areas were 109 ppm and 86 ppm, respectively. After installation of a new factory ventilation system, these seven patients recovered completely, and there were no new cases in the two-year follow-up.

Metabolic modelling in the development of cell factories by synthetic biology

PubMed Central

Jouhten, Paula

2012-01-01

Cell factories are commonly microbial organisms utilized for bioconversion of renewable resources to bulk or high value chemicals. Introduction of novel production pathways in chassis strains is the core of the development of cell factories by synthetic biology. Synthetic biology aims to create novel biological functions and systems not found in nature by combining biology with engineering. The workflow of the development of novel cell factories with synthetic biology is ideally linear which will be attainable with the quantitative engineering approach, high-quality predictive models, and libraries of well-characterized parts. Different types of metabolic models, mathematical representations of metabolism and its components, enzymes and metabolites, are useful in particular phases of the synthetic biology workflow. In this minireview, the role of metabolic modelling in synthetic biology will be discussed with a review of current status of compatible methods and models for the in silico design and quantitative evaluation of a cell factory. PMID:24688669

Non-classical photon correlation in a two-dimensional photonic lattice.

PubMed

Gao, Jun; Qiao, Lu-Feng; Lin, Xiao-Feng; Jiao, Zhi-Qiang; Feng, Zhen; Zhou, Zheng; Gao, Zhen-Wei; Xu, Xiao-Yun; Chen, Yuan; Tang, Hao; Jin, Xian-Min

2016-06-13

Quantum interference and quantum correlation, as two main features of quantum optics, play an essential role in quantum information applications, such as multi-particle quantum walk and boson sampling. While many experimental demonstrations have been done in one-dimensional waveguide arrays, it remains unexplored in higher dimensions due to tight requirement of manipulating and detecting photons in large-scale. Here, we experimentally observe non-classical correlation of two identical photons in a fully coupled two-dimensional structure, i.e. photonic lattice manufactured by three-dimensional femtosecond laser writing. Photon interference consists of 36 Hong-Ou-Mandel interference and 9 bunching. The overlap between measured and simulated distribution is up to 0.890 ± 0.001. Clear photon correlation is observed in the two-dimensional photonic lattice. Combining with controllably engineered disorder, our results open new perspectives towards large-scale implementation of quantum simulation on integrated photonic chips.

Correlations and fluctuations: Generalized factorial moments

NASA Astrophysics Data System (ADS)

Bialas, A.

2007-02-01

A systematic study of the relations between fluctuations of the extensive multiparticle variables and integrals of the inclusive multiparticle densities is presented. The generalized factorial moments are introduced and their physical meaning discussed. The effects of the additive conservation laws are analyzed.

Selective two-photon excitation of a vibronic state by correlated photons.

PubMed

Oka, Hisaki

2011-03-28

We theoretically investigate the two-photon excitation of a molecular vibronic state by correlated photons with energy anticorrelation. A Morse oscillator having three sets of vibronic states is used, as an example, to evaluate the selectivity and efficiency of two-photon excitation. We show that a vibrational mode can be selectively excited with high efficiency by the correlated photons, without phase manipulation or pulse-shaping techniques. This can be achieved by controlling the quantum correlation so that the photon pair concurrently has two pulse widths, namely, a temporally narrow width and a spectrally narrow width. Though this concurrence is seemingly contradictory, we can create such a photon pair by tailoring the quantum correlation between two photons.

Mobile Monitoring and Embedded Control System for Factory Environment

PubMed Central

Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

2013-01-01

This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones. PMID:24351642

Mobile monitoring and embedded control system for factory environment.

PubMed

Lian, Kuang-Yow; Hsiao, Sung-Jung; Sung, Wen-Tsai

2013-12-17

This paper proposes a real-time method to carry out the monitoring of factory zone temperatures, humidity and air quality using smart phones. At the same time, the system detects possible flames, and analyzes and monitors electrical load. The monitoring also includes detecting the vibrations of operating machinery in the factory area. The research proposes using ZigBee and Wi-Fi protocol intelligent monitoring system integration within the entire plant framework. The sensors on the factory site deliver messages and real-time sensing data to an integrated embedded systems via the ZigBee protocol. The integrated embedded system is built by the open-source 32-bit ARM (Advanced RISC Machine) core Arduino Due module, where the network control codes are built in for the ARM chipset integrated controller. The intelligent integrated controller is able to instantly provide numerical analysis results according to the received data from the ZigBee sensors. The Android APP and web-based platform are used to show measurement results. The built-up system will transfer these results to a specified cloud device using the TCP/IP protocol. Finally, the Fast Fourier Transform (FFT) approach is used to analyze the power loads in the factory zones. Moreover, Near Field Communication (NFC) technology is used to carry out the actual electricity load experiments using smart phones.

Nonlinear silicon photonics

NASA Astrophysics Data System (ADS)

Borghi, M.; Castellan, C.; Signorini, S.; Trenti, A.; Pavesi, L.

2017-09-01

Silicon photonics is a technology based on fabricating integrated optical circuits by using the same paradigms as the dominant electronics industry. After twenty years of fervid development, silicon photonics is entering the market with low cost, high performance and mass-manufacturable optical devices. Until now, most silicon photonic devices have been based on linear optical effects, despite the many phenomenologies associated with nonlinear optics in both bulk materials and integrated waveguides. Silicon and silicon-based materials have strong optical nonlinearities which are enhanced in integrated devices by the small cross-section of the high-index contrast silicon waveguides or photonic crystals. Here the photons are made to strongly interact with the medium where they propagate. This is the central argument of nonlinear silicon photonics. It is the aim of this review to describe the state-of-the-art in the field. Starting from the basic nonlinearities in a silicon waveguide or in optical resonator geometries, many phenomena and applications are described—including frequency generation, frequency conversion, frequency-comb generation, supercontinuum generation, soliton formation, temporal imaging and time lensing, Raman lasing, and comb spectroscopy. Emerging quantum photonics applications, such as entangled photon sources, heralded single-photon sources and integrated quantum photonic circuits are also addressed at the end of this review.

Terahertz photonic crystals

NASA Astrophysics Data System (ADS)

Jian, Zhongping

This thesis describes the study of two-dimensional photonic crystals slabs with terahertz time domain spectroscopy. In our study we first demonstrate the realization of planar photonic components to manipulate terahertz waves, and then characterize photonic crystals using terahertz pulses. Photonic crystal slabs at the scale of micrometers are first designed and fabricated free of defects. Terahertz time domain spectrometer generates and detects the electric fields of single-cycle terahertz pulses. By putting photonic crystals into waveguide geometry, we successfully demonstrate planar photonic components such as transmission filters, reflection frequency-selective filters, defects modes as well as superprisms. In the characterization study of out-of-plane properties of photonic crystal slabs, we observe very strong dispersion at low frequencies, guided resonance modes at middle frequencies, and a group velocity anomaly at high frequencies. We employ Finite Element Method and Finite-Difference Time-Domain method to simulate the photonic crystals, and excellent agreement is achieved between simulation results and experimental results.

Spin-photon interface and spin-controlled photon switching in a nanobeam waveguide

NASA Astrophysics Data System (ADS)

Javadi, Alisa; Ding, Dapeng; Appel, Martin Hayhurst; Mahmoodian, Sahand; Löbl, Matthias Christian; Söllner, Immo; Schott, Rüdiger; Papon, Camille; Pregnolato, Tommaso; Stobbe, Søren; Midolo, Leonardo; Schröder, Tim; Wieck, Andreas Dirk; Ludwig, Arne; Warburton, Richard John; Lodahl, Peter

2018-05-01

The spin of an electron is a promising memory state and qubit. Connecting spin states that are spatially far apart will enable quantum nodes and quantum networks based on the electron spin. Towards this goal, an integrated spin-photon interface would be a major leap forward as it combines the memory capability of a single spin with the efficient transfer of information by photons. Here, we demonstrate such an efficient and optically programmable interface between the spin of an electron in a quantum dot and photons in a nanophotonic waveguide. The spin can be deterministically prepared in the ground state with a fidelity of up to 96%. Subsequently, the system is used to implement a single-spin photonic switch, in which the spin state of the electron directs the flow of photons through the waveguide. The spin-photon interface may enable on-chip photon-photon gates, single-photon transistors and the efficient generation of a photonic cluster state.

Technology and Participation in Japanese Factories: The Consequences for Morale and Productivity.

ERIC Educational Resources Information Center

Hull, Frank; Azumi, Koya

1988-01-01

By fully using their human resources, Japanese factories mass produce goods of low cost and high quality. Participation in Japanese factories occurs in a more hierarchical framework than advocated in the Western model of worker democracy. (JOW)

Rare Kaon Decays, KEK experiment E391 and E14 at the Japan Physics and Accelerator Research Complex (J-PARC)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wah, Yau Wai

2012-12-06

The goal of the J-PARC neutral kaon experiment (E14/KOTO) is to discover and measure the rate of the kaon rare decay to pi-zero and two neutrinos. This flavor changing neutral current decay proceeds through second-order weak interactions. Other, as yet undiscovered particles, which can mediate the decay could provide an enhancement (or depletion) to the branching ratio which in the Standard Model is accurately predicted within a few percent to be 2.8x10-11. The experiment is designed to observe more than 100 events at the Standard Model branching. It is a follow-up of the KEK E391a experiment and has stage-2 approvalmore » by J-PARC PAC in 2007. E14/KOTO has collaborators from Japan (Kyoto, Osaka, Yamagata, Saga), US (Arizona State, Chicago, Michigan Ann Arbor), Taiwan (National Taiwan), Korea, and Russia (Dubna). The experiment exploits the 300kW 30-50 GeV proton delivery of the J-PARC accelerator with a hermetic high acceptance detector with a fine grained Cesium Iodide (CsI) crystal calorimeter, and state of the art electronic front end and data acquisition system. With the recovery of the tsunami disaster on March 11th 2011, E14 is scheduled to start collecting data in December 2012. During the detector construction phase, Chicago focuses on the front end electronics readout of the entire detector system, particularly the CsI calorimeter. The CsI crystals together with its photomultipliers were previously used at the Fermilab KTeV experiment (E832/E799), and were loaned to E14 via this Chicago DOE support. The new readout electronics includes an innovative 10-pole pulse-shaping technique coupled with high speed digitization (14-bit 125MHz and 12-bit 500MHz). This new instrument enables us to measure both energy and timing, particularly with timing resolution better than 100 psec. Besides the cost saving by elimination of the standard time to digital converters, it is now possible to measure the momenta of the final state photons for additional background

[Prevalence and influence factors of hypertension among mechanic factory workers].

PubMed

Pang, Li-Juan; Chen, Li-Zhang; Fu, Ben-Yan

2005-06-01

To determine the status and influence factors of hypertension on mechanic factory workers and to provide reference for further hypertension prevention and control. A cross-sectional study on 1205 workers (exposed to different noise levels) in Hunan was carried out by using questionaire and measuring the blood pressure of the workers and the noise exposure level in the workplace. The prevalence and the influence factors of hypertension among mechanic factory workers were analysed. The hypertension prevalence was 12.1%. Logistic regression analysis showed the body weight index (BMI), age, and history of hypertension in parents and accumulative noise dose levels influenced the hypertension prevalence. Controlling the body weight, reducing alcohol consumption, decreasing the sound pressure level in workshops and advocating healthy diet may reduce the prevalence rate of hypertension among mechanic factory workers.

Burnout Factories: The Challenge of Retaining Great Teachers in Charter Schools

ERIC Educational Resources Information Center

Fusco, Mark

2017-01-01

In its well-intentioned effort to create alternatives to public school dropout factories, the charter school sector has created teacher burnout factories. But it does not have to be this way. Charter schools can continue to maintain high standards while creating a more sustainable work environment for teachers. This article examines the teacher…

Nonlocal hyperconcentration on entangled photons using photonic module system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cao, Cong; Wang, Tie-Jun; Mi, Si-Chen

Entanglement distribution will inevitably be affected by the channel and environment noise. Thus distillation of maximal entanglement nonlocally becomes a crucial goal in quantum information. Here we illustrate that maximal hyperentanglement on nonlocal photons could be distilled using the photonic module and cavity quantum electrodynamics, where the photons are simultaneously entangled in polarization and spatial-mode degrees of freedom. The construction of the photonic module in a photonic band-gap structure is presented, and the operation of the module is utilized to implement the photonic nondestructive parity checks on the two degrees of freedom. We first propose a hyperconcentration protocol using twomore » identical partially hyperentangled initial states with unknown coefficients to distill a maximally hyperentangled state probabilistically, and further propose a protocol by the assistance of an ancillary single photon prepared according to the known coefficients of the initial state. In the two protocols, the total success probability can be improved greatly by introducing the iteration mechanism, and only one of the remote parties is required to perform the parity checks in each round of iteration. Estimates on the system requirements and recent experimental results indicate that our proposal is realizable with existing or near-further technologies.« less

Physics at high energy photon photon colliders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chanowitz, M.S.

I review the physic prospects for high energy photon photon colliders, emphasizing results presented at the LBL Gamma Gamma Collider Workshop. Advantages and difficulties are reported for studies of QCD, the electroweak gauge sector, supersymmetry, and electroweak symmetry breaking.

Engineering Photon-Photon Interactions within Rubidium-Filled Waveguides

NASA Astrophysics Data System (ADS)

Perrella, C.; Light, P. S.; Vahid, S. Afshar; Benabid, F.; Luiten, A. N.

2018-04-01

Strong photon-photon interactions are a required ingredient for deterministic two-photon optical quantum logic gates. Multiphoton transitions in dense atomic vapors have been shown to be a promising avenue for producing such interactions. The strength of a multiphoton interaction can be enhanced by conducting the interaction in highly confined geometries such as small-cross-section optical waveguides. We demonstrate, both experimentally and theoretically, that the strength of such interactions scale only with the optical mode diameter, d , not d2 as might be initially expected. This weakening of the interaction arises from atomic motion inside the waveguides. We create an interaction between two optical signals, at 780 and 776 nm, using the 5 S1 /2→5 D5 /2 two-photon transition in rubidium vapor within a range of hollow-core fibers with different core sizes. The interaction strength is characterized by observing the absorption and phase shift induced on the 780-nm beam, which is in close agreement with theoretical modeling that accounts for the atomic motion inside the fibers. These observations demonstrate that transit-time effects upon multiphoton transitions are of key importance when engineering photon-photon interactions within small-cross-section waveguides that might otherwise be thought to lead to enhanced optical nonlinearity through increased intensities.

Topological photonics: an observation of Landau levels for optical photons

NASA Astrophysics Data System (ADS)

Schine, Nathan; Ryou, Albert; Sommer, Ariel; Simon, Jonathan

We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Using a digital micromirror device to control both amplitude and phase, we inject arbitrary optical modes into our resonator. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We show that there is a conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids. This work was supported by DOE, DARPA, and AFOSR.

[Detection of occupational hazards in a large shipbuilding factory].

PubMed

Du, Weijia; Wang, Zhi; Zhang, Hai; Zhou, Liping; Huang, Minzhi; Liu, Yimin

2014-03-01

To provide evidence for the prevention and treatment of occupational diseases by the analysis of existing major occupational hazards and health conditions of workers in a large shipbuilding factory. Field investigation of occupational conditions was conducted to examine the existence of occupational hazards from 2009 to 2012 in a large shipbuilding factory, and then the results of physical examination among its workers were analyzed. Other than the metal dust (total dust), the levels of other dusts and manganese dioxide were beyond the national standard to various degrees, and through a sampling point detection, it was found that the levels of manganese dioxide exceeded the standard by 42.8%. The maximum time-weighted average concentration in individuals was 27.927 mg/m(3), much higher than the national standard limit. For harmful gas detection in individuals, xylene was 38.4%above the standard level (the highest concentration reached 1447.7 mg/m(3)); moreover, both toluene and ethylbenzene exceeded the national standard at different levels. Among the noise-exposed workers, 71%worked in the environment where the daily noise was above the limit of the national standard (85 dB). Physical examinations in 2010 and 2012 showed that the abnormal rate of audiometry in workers was higher than 15%. Dust (total dust), manganese dioxide, benzene, and noise are the main occupational hazards among the workers in the large shipbuilding factory, and strict protection and control for these hazards should be implemented for the workers in the factory.

Development of FARICH detector for particle identification system at accelerators

NASA Astrophysics Data System (ADS)

Finogeev, D. A.; Kurepin, A. B.; Razin, V. I.; Reshetin, A. I.; Usenko, E. A.; Barnyakov, A. Yu.; Barnyakov, M. Yu.; Bobrovnikov, V. S.; Buzykaev, A. R.; Kasyanenko, P. V.; Kononov, S. A.; Kravchenko, E. A.; Kuyanov, I. A.; Onuchin, A. P.; Ovtin, I. V.; Podgornov, N. A.; Talyshev, A. A.; Danilyuk, A. F.

2018-01-01

Aerogel has been successfully used as a radiator in Cherenkov detectors. In 2004, a multilayer aerogel providing Cherenkov ring focusing was proposed and produced. FARICH (Focusing Aerogel Rich Imaging CHerenkov) detectors such as ARICH for Belle-II (KEK, Japan), Forward RICH for PANDA detector (FAIR, Germany), and FARICH for the Super Charm-Tau factory project (BINP, Novosibirsk) have been developed based on this aerogel. Prototypes of FARICH detector based on MRS APD and Philips DPC photosensors were developed and tested in the framework of this project. An angular resolution for Cherenkov rings of 3.6 mrad was achieved.

An Application of Fractional Factorial Designs to Study Drug Combinations

PubMed Central

Jaynes, Jessica; Ding, Xianting; Xu, Hongquan; Wong, Weng Kee; Ho, Chih-Ming

2013-01-01

Herpes simplex virus type 1 (HSV-1) is known to cause diseases of various severities. There is increasing interest to find drug combinations to treat HSV-1 by reducing drug resistance and cytotoxicity. Drug combinations offer potentially higher efficacy and lower individual drug dosage. In this paper, we report a new application of fractional factorial designs to investigate a biological system with HSV-1 and six antiviral drugs, namely, Interferon-alpha, Interferon-beta, Interferon-gamma, Ribavirin, Acyclovir, and TNF-alpha. We show how the sequential use of two- and three-level fractional factorial designs can screen for important drugs and drug interactions, as well as determine potential optimal drug dosages through the use of contour plots. Our initial experiment using a two-level fractional factorial design suggests that there is model inadequacy and drug dosages should be reduced. A follow-up experiment using a blocked three-level fractional factorial design indicates that TNF-alpha has little effect and HSV-1 infection can be suppressed effectively by using a right combination of the other five antiviral drugs. These observations have practical implications in the understanding of antiviral drug mechanism that can result in better design of antiviral drug therapy. PMID:22859316

Effects of lighting and air-conditioning systems on growth weight and functional composition of frill-lettuce produced in plant factory

NASA Astrophysics Data System (ADS)

Yoshida, Atsumasa; Okamura, Nobuya; Furukawa, Hajime; Myojin, Chiho; Moriuchi, Koji; Kinoshita, Shinichi

2017-06-01

The aim of the present study was to develop optimal air-conditioning systems for plant factories. To verify the effect of particular air-conditioning and lighting systems, cultivation experiments were performed with frill-lettuce for two weeks. In the present study, the relationship between the cultivation condition, the yield (i.e., increase in edible portion weight), and the functional components were discussed. Based on the measured data, increased photosynthetic photon flux density increased antioxidative activity and edible portion weight, possibly because high light intensities are stressful for frill lettuce. Antioxidative activity also increased under conditions of low CO2 concentration, weak and strong winds, and high air temperature because these conditions became stresses for the plants. However, a decrease in edible portion weight was observed under these conditions, implying there is a negative correlation between antioxidative activity and edible portion weight.

Generation of Single Photons and Entangled Photon Pairs from a Quantum Dot

NASA Astrophysics Data System (ADS)

Yamamoto, Y.; Pelton, M.; Santori, C.; Solomon, G. S.

2002-10-01

Current quantum cryptography systems are limited by the Poissonian photon statistics of a standard light source: a security loophole is opened up by the possibility of multiple-photon pulses. By replacing the source with a single-photon emitter, transmission rates of secure information can be improved. A single photon source is also essential to implement a linear optics quantum computer. We have investigated the use of single self-assembled InAs/GaAs quantum dots as such single-photon sources, and have seen a hundred-fold reduction in the multi-photon probability as compared to Poissonian pulses. An extension of our experiment should also allow for the generation of triggered, polarizationentangled photon pairs.

EDITORIAL: Selected papers from Photon08 Selected papers from Photon08

NASA Astrophysics Data System (ADS)

Boardman, Allan D.; Harvey, Andrew; Jones, Julian C.

2009-05-01

Photon08 was the fifth in a biennial series of events that began in 2000 and has grown to become the largest optics research meeting in the UK. Two of the co-located constituent conferences of Photon08 were generated by the Institute of Physics. These were the Optics and Photonics Division conference plus QEP-18 organised by the Quantum Electronics and Photonics Group. In addition, Photon08 contained a major exhibition and an Industry Technology Programme. Photon08 was organised by the UK Consortium for Photonics and Optics (UKCPO), whose members comprise all organisations that represent the UK optics community, whether learned societies, professional institutions, trade associations, or regional special interest groups. In hosting the Photon series, it is the objective of the UKCPO to provide a single forum for UK optics. Photon08 was held at Heriot-Watt University, Edinburgh, 26-29 August 2008, and was attended by around 500 people. The international representation was very impressive and the range of topics was mapped onto a wide audience, which embraced every aspect of photonics from quantum information processing to biomedical imaging and technology transfer into the commercial domain. The purpose of this special issue is to present a characteristic selection of the research reported at Photon08. On behalf of the conference, we are very grateful to the editors of Journal of Optics A: Pure and Applied Optics for the opportunity to provide this archival record. The majority of the papers in this special issue follow the theme of measurement and instrumentation. This reflects one of the traditional strengths of the UK community that spans the interests of the Optical Group, the Optics and Photonics Division and the Instrument Science and Technology Group of the Institute of Physics, and the Fringe Analysis Special Interest Group. The other papers illustrate other UK strengths in quantum processing and nonlinear optics. There can be few areas of physics so diverse

Investigation of angular dependence on photonic bandgap for 1-D photonic crystal

NASA Astrophysics Data System (ADS)

Nigam, Anjali; Suthar, B.; Bhargava, A.; Vijay, Y. K.

2018-05-01

In the present communication, we study the one-dimensional photonic crystal structure. The photonic band structure has been obtained using Plane Wave Expansion Method (PWEM). The studied has been extended to investigate the angular dependence on photonic bandgap for 1-D photonic crystal. The photonic bandgap is same both for TE and TM mode for normal incidence, while both mode move separate with an incidence angle. The photonic bandgap is almost unaffected with angle for TE mode while the bandgap decreases with an incidence angle for TM mode.

Frequency Agile Microwave Photonic Notch Filter in a Photonic Chip

DTIC Science & Technology

2016-10-21

AFRL-AFOSR-JP-TR-2016-0087 Frequency Agile Microwave Photonic Notch Filter in a Photonic Chip Benjamin Eggleton UNIVERSITY OF SYDNEY Final Report 10...REPORT TYPE      Final 3.  DATES COVERED (From - To)      14 May 2014 to 13 May 2016 4.  TITLE AND SUBTITLE Frequency Agile Microwave Photonic Notch Filter ...primary objective is to explore a novel class microwave photonic (MWP) notch filter with a very narrow isolation bandwidth, an ultrahigh stopband

Autocrine and/or paracrine insulin-like growth factor-I activity in skeletal muscle

NASA Technical Reports Server (NTRS)

Adams, Gregory R.

2002-01-01

Similar to bone, skeletal muscle responds and adapts to changes in loading state via mechanisms that appear to be intrinsic to the muscle. One of the mechanisms modulating skeletal muscle adaptation it thought to involve the autocrine and/or paracrine production of insulinlike growth factor-I. This brief review outlines components of the insulinlike growth factor-I system as it relates to skeletal muscle and provides the rationale for the theory that insulinlike growth factor-I is involved with muscle adaptation.

Prompt photon production and photon-jet correlations at the LHC

NASA Astrophysics Data System (ADS)

Klasen, Michael; Klein-Bösing, Christian; Poppenborg, Hendrik

2018-03-01

Next-to-leading order predictions matched to parton showers are compared with recent ATLAS data on isolated photon production and CMS data on associated photon and jet production in pp and pPb collisions at different centre-of-mass energies of the LHC. We find good agreement and, as expected, considerably reduced scale uncertainties compared to previous theoretical calculations. Predictions are made for the ratio of inclusive photons over decay photons R γ , an important quantity to evaluate the significance of additional photon sources, e.g. thermal radiation from a Quark-Gluon-Plasma, and for distributions in the parton momentum fraction in lead ions x Pb obs , that could be determined by ALICE, ATLAS, CMS and LHCb in ongoing analyses of photon+jet production in pPb collisions at √{s_{N N}} = 5.02 TeV. These data should have an important impact on the determination of nuclear effects such as shadowing at low x.

Bose-Einstein condensation of photons in a 'white-wall' photon box

NASA Astrophysics Data System (ADS)

Klärs, Jan; Schmitt, Julian; Vewinger, Frank; Weitz, Martin

2011-01-01

Bose-Einstein condensation, the macroscopic ground state occupation of a system of bosonic particles below a critical temperature, has been observed in cold atomic gases and solid-state physics quasiparticles. In contrast, photons do not show this phase transition usually, because in Planck's blackbody radiation the particle number is not conserved and at low temperature the photons disappear in the walls of the system. Here we report on the realization of a photon Bose-Einstein condensate in a dye-filled optical microcavity, which acts as a "white-wall" photon box. The cavity mirrors provide a trapping potential and a non-vanishing effective photon mass, making the system formally equivalent to a two-dimensional gas of trapped massive bosons. Thermalization of the photon gas is reached in a number conserving way by multiple scattering off the dye molecules. Signatures for a BEC upon increased photon density are: a spectral distribution that shows Bose-Einstein distributed photon energies with a macroscopically populated peak on top of a broad thermal wing, the observed threshold of the phase transition showing the predicted absolute value and scaling with resonator geometry, and condensation appearing at the trap centre even for a spatially displaced pump spot.

Hardwood log grades and lumber grade yields for factory lumber logs

Treesearch

Leland F. Hanks; Glenn L. Gammon; Robert L. Brisbin; Everette D. Rast

1980-01-01

The USDA Forest Service Standard Grades for Hardwood Factory Lumber Logs are described, and lumber grade yields for 16 species and 2 species groups are presented by log grade and log diameter. The grades enable foresters, log buyers, and log sellers to select and grade those log suitable for conversion into standard factory grade lumber. By using the apropriate lumber...

Molecular pathways: transcription factories and chromosomal translocations.

PubMed

Osborne, Cameron S

2014-01-15

The mammalian nucleus is a highly complex structure that carries out a diverse range of functions such as DNA replication, cell division, RNA processing, and nuclear export/import. Many of these activities occur at discrete subcompartments that intersect with specific regions of the genome. Over the past few decades, evidence has accumulated to suggest that RNA transcription also occurs in specialized sites, called transcription factories, that may influence how the genome is organized. There may be certain efficiency benefits to cluster transcriptional activity in this way. However, the clustering of genes at transcription factories may have consequences for genome stability, and increase the susceptibility to recurrent chromosomal translocations that lead to cancer. The relationships between genome organization, transcription, and chromosomal translocation formation will have important implications in understanding the causes of therapy-related cancers. ©2013 AACR.

Making Connections: After the Factories Revisited.

ERIC Educational Resources Information Center

Rosenfeld, Stuart A.; Bergman, Edward M.

This analysis of employment patterns in the American South extends a 1985 report, "After the Factories: Changing Employment Patterns in the Rural South," which was based on the years between 1977-1982. The 1985 report included Texas, but this analysis includes only the 12 Southern Growth Policies Board (SGPB) member states. This new…

Factorial Composition of Counsellor Effectiveness Scale

ERIC Educational Resources Information Center

Oluseyi, Adeyemo Emily; Oreoluwa, Shaba Veronica

2014-01-01

The study developed a set of items that could measure counsellor effectiveness. It reduced the initial set of variables related to counsellor effectiveness to such number of variables that are generally perceived as indicative of counsellor effectiveness and determined the factorial composition of the scale. in order to identify the major factors…

A survey of airborne and skin exposures to chemicals in footwear and equipment factories in Thailand.

PubMed

Todd, Lori A; Mottus, Kathleen; Mihlan, Gary J

2008-03-01

This research reports on a pilot industrial hygiene study that was performed at four footwear factories and two equipment factories in Thailand. Workers in these factories were exposed through inhalation and dermal contact to a large number of organic vapors from solvents and cements that were hand applied. In addition, these workers were exposed to highly toxic isocyanates primarily through the dermal route. A total of 286 personal air samples were obtained at the four footwear factories using organic vapor monitors; individual job tasks were monitored using a real-time MIRAN Spectrometer. A total of 64 surface, tool, or hand samples were monitored for isocyanates using surface contamination detectors. Real-time measurements were also obtained for organic vapors in two equipment factories. From 8% to 21% of the workers sampled in each footwear factory were overexposed to mixtures of chemicals from solvents and cements. Up to 100% of the workers performing specific job tasks were overexposed to mixtures of chemicals. From 39% to 69% of the surface samples were positive for unreacted isocyanates. Many of the real-time measurements obtained in the equipment factories exceeded occupational exposure limits. Personal protective equipment and engineering controls were inadequate in all of the factories.

A photon-photon quantum gate based on a single atom in an optical resonator.

PubMed

Hacker, Bastian; Welte, Stephan; Rempe, Gerhard; Ritter, Stephan

2016-08-11

That two photons pass each other undisturbed in free space is ideal for the faithful transmission of information, but prohibits an interaction between the photons. Such an interaction is, however, required for a plethora of applications in optical quantum information processing. The long-standing challenge here is to realize a deterministic photon-photon gate, that is, a mutually controlled logic operation on the quantum states of the photons. This requires an interaction so strong that each of the two photons can shift the other's phase by π radians. For polarization qubits, this amounts to the conditional flipping of one photon's polarization to an orthogonal state. So far, only probabilistic gates based on linear optics and photon detectors have been realized, because "no known or foreseen material has an optical nonlinearity strong enough to implement this conditional phase shift''. Meanwhile, tremendous progress in the development of quantum-nonlinear systems has opened up new possibilities for single-photon experiments. Platforms range from Rydberg blockade in atomic ensembles to single-atom cavity quantum electrodynamics. Applications such as single-photon switches and transistors, two-photon gateways, nondestructive photon detectors, photon routers and nonlinear phase shifters have been demonstrated, but none of them with the ideal information carriers: optical qubits in discriminable modes. Here we use the strong light-matter coupling provided by a single atom in a high-finesse optical resonator to realize the Duan-Kimble protocol of a universal controlled phase flip (π phase shift) photon-photon quantum gate. We achieve an average gate fidelity of (76.2 ± 3.6) per cent and specifically demonstrate the capability of conditional polarization flipping as well as entanglement generation between independent input photons. This photon-photon quantum gate is a universal quantum logic element, and therefore could perform most existing two-photon operations

76 FR 77175 - New York Fun Factory Fireworks Display, Western Long Island Sound; Mamaroneck, NY

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-12

...-AA00 New York Fun Factory Fireworks Display, Western Long Island Sound; Mamaroneck, NY AGENCY: Coast... in support of the New York Fun Factory Fireworks display. This action is necessary to provide for the... the Coast Guard to define regulatory safety zones. On May 10, 2012 New York Fun Factory Events is...

Perspective: Photonic flatbands

NASA Astrophysics Data System (ADS)

Leykam, Daniel; Flach, Sergej

2018-07-01

Flatbands are receiving increasing theoretical and experimental attention in the field of photonics, in particular in the field of photonic lattices. Flatband photonic lattices consist of arrays of coupled waveguides or resonators where the peculiar lattice geometry results in at least one completely flat or dispersionless band in its photonic band structure. Although bearing a strong resemblance to structural slow light, this independent research direction is instead inspired by analogies with "frustrated" condensed matter systems. In this Perspective, we critically analyze the research carried out to date, discuss how this exotic physics may lead to novel photonic device applications, and chart promising future directions in theory and experiment.

Quantum dot single-photon switches of resonant tunneling current for discriminating-photon-number detection

PubMed Central

Weng, Qianchun; An, Zhenghua; Zhang, Bo; Chen, Pingping; Chen, Xiaoshuang; Zhu, Ziqiang; Lu, Wei

2015-01-01

Low-noise single-photon detectors that can resolve photon numbers are used to monitor the operation of quantum gates in linear-optical quantum computation. Exactly 0, 1 or 2 photons registered in a detector should be distinguished especially in long-distance quantum communication and quantum computation. Here we demonstrate a photon-number-resolving detector based on quantum dot coupled resonant tunneling diodes (QD-cRTD). Individual quantum-dots (QDs) coupled closely with adjacent quantum well (QW) of resonant tunneling diode operate as photon-gated switches- which turn on (off) the RTD tunneling current when they trap photon-generated holes (recombine with injected electrons). Proposed electron-injecting operation fills electrons into coupled QDs which turn “photon-switches” to “OFF” state and make the detector ready for multiple-photons detection. With proper decision regions defined, 1-photon and 2-photon states are resolved in 4.2 K with excellent propabilities of accuracy of 90% and 98% respectively. Further, by identifying step-like photon responses, the photon-number-resolving capability is sustained to 77 K, making the detector a promising candidate for advanced quantum information applications where photon-number-states should be accurately distinguished. PMID:25797442

Quantum dot single-photon switches of resonant tunneling current for discriminating-photon-number detection.

PubMed

Weng, Qianchun; An, Zhenghua; Zhang, Bo; Chen, Pingping; Chen, Xiaoshuang; Zhu, Ziqiang; Lu, Wei

2015-03-23

Low-noise single-photon detectors that can resolve photon numbers are used to monitor the operation of quantum gates in linear-optical quantum computation. Exactly 0, 1 or 2 photons registered in a detector should be distinguished especially in long-distance quantum communication and quantum computation. Here we demonstrate a photon-number-resolving detector based on quantum dot coupled resonant tunneling diodes (QD-cRTD). Individual quantum-dots (QDs) coupled closely with adjacent quantum well (QW) of resonant tunneling diode operate as photon-gated switches- which turn on (off) the RTD tunneling current when they trap photon-generated holes (recombine with injected electrons). Proposed electron-injecting operation fills electrons into coupled QDs which turn "photon-switches" to "OFF" state and make the detector ready for multiple-photons detection. With proper decision regions defined, 1-photon and 2-photon states are resolved in 4.2 K with excellent propabilities of accuracy of 90% and 98% respectively. Further, by identifying step-like photon responses, the photon-number-resolving capability is sustained to 77 K, making the detector a promising candidate for advanced quantum information applications where photon-number-states should be accurately distinguished.

A Project to Design and Build the Magnets for a New Test Beamline, the ATF2, at KEK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spencer, Cherrill M.; /slac; Sugahara, Ryuhei

2011-02-07

In order to achieve the high luminosity required at the proposed International Linear Collider (ILC), it is critical to focus the beams to nanometer size with the ILC Beam Delivery System, and to maintain the beams collisions with a nanometer-scale stability. To establish the technologies associated with this ultra-high precision beam handling, a special beamline has been designed and built as an extension of the existing extraction beamline of the Accelerator Test Facility at KEK, Japan. The ATF provides an adequate ultra-low emittance electron beam that is comparable to the ILC requirements; the ATF2 mimics the ILC final focus systemmore » to create a tightly focused, stable beam. There are 37 magnets in the ATF2, 29 quadrupoles, 5 sextupoles and 3 bends. These magnets had to be acquired in a short time and at minimum cost, which led to various acquisition strategies; but nevertheless they had to meet strict requirements on integrated strength, physical dimensions, compatibility with existing magnet movers and beam position monitors, mechanical stability and field stability and quality. This paper will describe how 2 styles of quadrupoles, 2 styles of sextupoles, one dipole style and their supports were designed, fabricated, refurbished or modified, measured and aligned by a small team of engineers from 3 continents.« less

R&D Toward a Neutrino Factory and Muon Collider

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zisman, Michael S

2011-03-20

Significant progress has been made in recent years in R&D towards a neutrino factory and muon collider. The U.S. Muon Accelerator Program (MAP) has been formed recently to expedite the R&D efforts. This paper will review the U.S. MAP R&D programs for a neutrino factory and muon collider. Muon ionization cooling research is the key element of the program. The first muon ionization cooling demonstration experiment, MICE (Muon Ionization Cooling Experiment), is under construction now at RAL (Rutherford Appleton Laboratory) in the UK. The current status of MICE will be described.

Environmental sampling of lead near a battery reprocessing factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leung, H.W.

1988-09-01

Exposed workers in lead smelting plants and lead storage battery factories have reported illnesses related to inhalation of lead oxide fumes. The residential community of La Gloria, a town of about 15,000 people located approximately 13 km southwest of Tijuana, Baja California, Mexico was an area where residents were concerned about possible health effects and environmental contamination from lead due to the proximity of battery factory that used lead oxide in the battery grid separation procedure. This study was undertaken to investigate the lead levels in the soil, plant and water collected in various areas around this battery reprocessing plant.

Undergraduate Students' Initial Conceptions of Factorials

ERIC Educational Resources Information Center

Lockwood, Elise; Erickson, Sarah

2017-01-01

Counting problems offer rich opportunities for students to engage in mathematical thinking, but they can be difficult for students to solve. In this paper, we present a study that examines student thinking about one concept within counting, factorials, which are a key aspect of many combinatorial ideas. In an effort to better understand students'…

An Epiphany in a Toilet Factory

ERIC Educational Resources Information Center

Cobb, Catlin

2009-01-01

In this article, the author shares her experiences of the universality of art making and artistic experience of being a dancer and teaching artist. She describes her performance at Kohler, a worldwide leader in plumbing products in Spartanburg, South Carolina, where she had an epiphany dancing in a toilet factory--a sudden, intuitive moment of…

Photonic crystal light source

DOEpatents

Fleming, James G [Albuquerque, NM; Lin, Shawn-Yu [Albuquerque, NM; Bur, James A [Corrales, NM

2004-07-27

A light source is provided by a photonic crystal having an enhanced photonic density-of-states over a band of frequencies and wherein at least one of the dielectric materials of the photonic crystal has a complex dielectric constant, thereby producing enhanced light emission at the band of frequencies when the photonic crystal is heated. The dielectric material can be a metal, such as tungsten. The spectral properties of the light source can be easily tuned by modification of the photonic crystal structure and materials. The photonic crystal light source can be heated electrically or other heating means. The light source can further include additional photonic crystals that exhibit enhanced light emission at a different band of frequencies to provide for color mixing. The photonic crystal light source may have applications in optical telecommunications, information displays, energy conversion, sensors, and other optical applications.

9. NORTHEAST FROM SOUTH ENTRANCE ACROSS RECEIVING AREA OF FACTORY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. NORTHEAST FROM SOUTH ENTRANCE ACROSS RECEIVING AREA OF FACTORY PAST THE GLASS-ENCLOSED OFFICE TOWARD SHOP AREA. BESIDE THE VERTICAL POST ROOF SUPPORT IN THE LEFT FOREGROUND IS A SCALE AND DRAFTING TABLE. BESIDE THE OFFICE WALL ON THE RIGHT IS A SMALL SHOP REPAIR BENCH, WHILE ABOVE THE OFFICE WINDOWS ARE BOXES OF COMPANY MANUSCRIPT BUSINESS RECORDS. THE WELDED METAL PIPE RACK IS A MODERN INTRUSION. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

FFAGs: Front-end for neutrino factories and medical accelerators

NASA Astrophysics Data System (ADS)

Mori, Yoshiharu

The idea of Fixed Field Alternating Gradient (FFAG) accelerator was originated by different people and groups in the early 1950s. It was independently introduced by Ohkawa [Ohkawa (1953)], Symon et al. [Symon et al. (1956)], and Kolomensky [Kolomensky and Lebedev (1966)] when the strong Alternate Gradient (AG) focusing and the phase stability schemes were applied to particle acceleration. The first FFAG electron model was developed in the MURA accelerator project led by Kerst and Cole in the late 1950s. Since then, they have fabricated several electron models in the early 1960s [Symon et al. (1956)]. However, the studies did not lead to a single practical FFAG accelerator for the following 50 years. Because of the difficulties of treating non-linear magnetic field and RF acceleration for non-relativistic particles, the proton FFAG, especially, was not accomplished until recently. In 2000, the FFAG concept was revived with the world's first proton FFAG (POP) which was developed at KEK [Aiba (2000); Mori (1999)]. Since then, in many places [Berg (2004); Johnstone et al. (2004); Mori (2011); Ruggiero (2004); Trbojevic (2004)], FFAGs have been developed and constructed...

Does open-air exposure to volatile organic compounds near a plastic recycling factory cause health effects?

PubMed

Yorifuji, Takashi; Noguchi, Miyuki; Tsuda, Toshihide; Suzuki, Etsuji; Takao, Soshi; Kashima, Saori; Yanagisawa, Yukio

2012-01-01

After a plastic reprocessing factory began to operate in August 2004, the residents around the factory in Neyagawa, Osaka, Japan, began to complain of symptoms. Therefore, we conducted an exposure assessment and a population-based epidemiological study in 2006. To assess exposure, volatile organic compounds (VOCs) and total VOCs were measured at two locations in the vicinity of the factory. In the population-based study, a total of 3,950 residents were targeted. A self-administered questionnaire was used to collect information about subjects' mucocutaneous or respiratory symptoms. Using logistic regression models, we compared the prevalence of symptoms in July 2006 by employing the farthest area from the factory as a reference, and prevalence odds ratios (PORs) and their 95% confidence intervals (CIs) were estimated. The concentration of total VOCs was higher in the vicinity of the factory. The prevalence of mucocutaneous and respiratory symptoms was the highest among the residents in the closest area to the factory. Some symptoms were significantly increased among the residents within 500 m of the factory compared with residents of an area 2800 m from the factory: e.g., sore throat (POR=3.2, 95% CI: 1.3-8.0), eye itch (POR=3.0, 95% CI: 1.5-6.0), eye discharge (POR=6.0, 95% CI: 2.3-15.9), eczema (POR=3.0, 95% CI: 1.1-7.9) and sputum (POR=2.4, 95% CI: 1.1-5.1). Despite of the limitations of this study, these results imply a possible association of open-air VOCs with mucocutaneous and respiratory symptoms. Because this kind of plasticre cycling factory only recently came into operation, more attention should be paid to the operation of plastic recycling factories in the environment.

Means and method for calibrating a photon detector utilizing electron-photon coincidence

NASA Technical Reports Server (NTRS)

Srivastava, S. K. (Inventor)

1984-01-01

An arrangement for calibrating a photon detector particularly applicable for the ultraviolet and vacuum ultraviolet regions is based on electron photon coincidence utilizing crossed electron beam atom beam collisions. Atoms are excited by electrons which lose a known amount of energy and scatter with a known remaining energy, while the excited atoms emit photons of known radiation. Electrons of the known remaining energy are separated from other electrons and are counted. Photons emitted in a direction related to the particular direction of scattered electrons are detected to serve as a standard. Each of the electrons is used to initiate the measurements of a time interval which terminates with the arrival of a photon exciting the photon detector. Only the number of time intervals related to the coincidence correlation and of electrons scattered in the particular direction with the known remaining energy and photons of a particular radiation level emitted due to the collisions of such scattered electrons are counted. The detector calibration is related to the number of counted electrons and photons.

Poor but Not Powerless: Women Workers in Production Chain Factories in China

ERIC Educational Resources Information Center

Ma, Lang; Jacobs, Francine

2010-01-01

The present study demonstrates the processes by which 12 young women working in four production chain factories in China shape their own lives--their developmental trajectories--during the period following their entry into factory work. One-on-one, in-depth, semi-structured interviews were conducted in August, 2005, as part of an evaluation…

Quality of Life Among Thai Workers in Textile Dyeing Factories

PubMed Central

Kittipichai, Wirin; Arsa, Rattanaporn; Jirapongsuwan, Ann; Singhakant, Chatchawal

2015-01-01

The purpose of a cross-sectional study was to investigate factors influencing the quality of life among Thai workers in textile dyeing factories. Samples included 205 Thai workers from five textile dyeing factories located in the suburban area of Bangkok in Thailand. Data were collected with a self-administered questionnaire. Scales of the questionnaire had reliability coefficients ranging from 0.70–0.91. The results revealed that the overall quality of life among workers was most likely between good and moderate levels, and the percentage-mean score was 74.77. The seven factors associated with the overall quality of life were co-worker relationships, safety at work in the dimension of accident prevention, job characteristics, supervisory relationships, welfares, marital status, and physical environment. Furthermore, co-worker relationships, accident prevention, and marital status were three considerable predictors accounted for 23% of the variance in the overall quality of life among workers in textile dyeing factories. PMID:25948458

Dermatitis in a rubber tyre factory.

PubMed

Zina, A M; Bedello, P G; Cane, D; Bundino, S; Benedetto, A

1987-07-01

An outbreak of occupational dermatitis in a rubber tyre factory is reported. An unusual clinical picture was recognized. Patch tests revealed a high sensitization rate to the MBT derivative used: 2-(2'-4'dinitrophenylthio)benzothiazole. Since tests with MBT mix and dinitrophenol were negative; sensitization to a contaminant was suspected. DNCB was traced as the substance responsible.

Study of the effect of temperature, irradiance and salinity on growth and yessotoxin production by the dinoflagellate Protoceratium reticulatum in culture by using a kinetic and factorial approach.

PubMed

Paz, Beatriz; Vázquez, José A; Riobó, Pilar; Franco, José M

2006-10-01

A complete first order orthogonal plan was used to optimize the growth and the production of yessotoxin (YTX) by the dinoflagellate Protoceratium reticulatum in culture by controlling salinity, temperature and irradiance. Initially, an approach to the kinetic data of cellular density and YTX production for each one of the experimental design conditions was performed. The P. reticulatum growth and YTX production were fitted to logistical equations and to a first-order kinetic model, respectively. The parameters obtained from this adjustment were used as dependent variables for the formulation of the empirical equations of the factorial design tested. The results showed that in practically all the cases for both, P. reticulatum growth and YTX production, irradiance is the primary independent variable and has a positive effect in the range 50-90 micromol photons m(-2) s(-1). Additionally, in certain specific cases, temperature reveals significant positive effects when maintained between 15 and 23 degrees C and salinity in the range of 20-34 displays negative effects. Despite the narrow ranges used in the work, results showed the suitability of factorial analysis to evaluate the optimal conditions for growth and yessotoxin production by the dinoflagellate P. reticulatum.

Amplified Photon Upconversion by Photonic Shell of Cholesteric Liquid Crystals.

PubMed

Kang, Ji-Hwan; Kim, Shin-Hyun; Fernandez-Nieves, Alberto; Reichmanis, Elsa

2017-04-26

As an effective platform to exploit triplet-triplet-annihilation-based photon upconversion (TTA-UC), microcapsules composed of a fluidic UC core and photonic shell are microfluidically prepared using a triple emulsion as the template. The photonic shell consists of cholesteric liquid crystals (CLCs) with a periodic helical structure, exhibiting a photonic band gap. Combined with planar anchoring at the boundaries, the shell serves as a resonance cavity for TTA-UC emission and enables spectral tuning of the UC under low-power-density excitation. The CLC shell can be stabilized by introducing a polymerizable mesogen in the LC host. Because of the microcapsule spherical symmetry, spontaneous emission of the delayed fluorescence is omnidirectionally amplified at the edge of the stop band. These results demonstrate the range of opportunities provided by TTA-UC systems for the future design of low-threshold photonic devices.

Stimulated photon emission and two-photon Raman scattering in a coupled-cavity QED system

PubMed Central

Li, C.; Song, Z.

2016-01-01

We study the scattering problem of photon and polariton in a one-dimensional coupled-cavity system. Analytical approximate analysis and numerical simulation show that a photon can stimulate the photon emission from a polariton through polariton-photon collisions. This observation opens the possibility of photon-stimulated transition from insulating to radiative phase in a coupled-cavity QED system. Inversely, we also find that a polariton can be generated by a two-photon Raman scattering process. This paves the way towards single photon storage by the aid of atom-cavity interaction. PMID:26877252

21. SOUTH THROUGH FACTORY FROM NEAR NORTHEAST CORNER TOWARD SOUTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. SOUTH THROUGH FACTORY FROM NEAR NORTHEAST CORNER TOWARD SOUTH FRONT OF BUILDING. VISIBLE FROM LEFT TO RIGHT ARE CIRCA 1865 METAL-TURNING LATHE; CIRCA 1875 POWER SHEAR, PUNCH, AND RIVETING MACHINE (WITH FLOORING RAISED TO SHOW OPERATOR'S 'PIT'); LINE SHAFT WITH PULLEYS AND BELTS FOR OPERATING MACHINERY; PERMANENT WOODEN LADDER TO SKYLIGHT AREA (LOCATION OF CIRCA 1920 ELECTRIC MOTOR WHICH POWERED LINE SHAFT); AND BUFFALO FORGE CO. HAND SHEAR FOR ANGLE STEEL. - Kregel Windmill Company Factory, 1416 Central Avenue, Nebraska City, Otoe County, NE

The Idea Factory: An Interactive Intergroup Exercise

ERIC Educational Resources Information Center

Rosh, Lisa; Leach, Evan

2011-01-01

This article outlines the Idea Factory exercise, an interactive exercise designed to help participants examine group, individual, and organizational factors that affect intergroup conflict. Specific emphasis is placed on exploring the relationship between intra- and intergroup dynamics and identifying managerial practices that foster effective…

Jean Piaget: Images of a life and his factory.

PubMed

Burman, Jeremy Trevelyan

2012-08-01

In this article, I use a new book about Jean Piaget to introduce a new historical method: examining "psychological factories." I also discuss some of the ways that "Great Men" are presented in the literature, as well as opportunities for new projects if one approaches the history of the discipline differently and examines the conditions that made that greatness possible. To that end, the article includes many details about Piaget that have never before been discussed in English. Attention is drawn, in particular, to Piaget's collaborators: the hundreds of workers at his factory in Geneva, many of whom were women. (PsycINFO Database Record (c) 2012 APA, all rights reserved).

Economic evaluation of factorial randomised controlled trials: challenges, methods and recommendations

PubMed Central

Gray, Alastair

2017-01-01

Increasing numbers of economic evaluations are conducted alongside randomised controlled trials. Such studies include factorial trials, which randomise patients to different levels of two or more factors and can therefore evaluate the effect of multiple treatments alone and in combination. Factorial trials can provide increased statistical power or assess interactions between treatments, but raise additional challenges for trial‐based economic evaluations: interactions may occur more commonly for costs and quality‐adjusted life‐years (QALYs) than for clinical endpoints; economic endpoints raise challenges for transformation and regression analysis; and both factors must be considered simultaneously to assess which treatment combination represents best value for money. This article aims to examine issues associated with factorial trials that include assessment of costs and/or cost‐effectiveness, describe the methods that can be used to analyse such studies and make recommendations for health economists, statisticians and trialists. A hypothetical worked example is used to illustrate the challenges and demonstrate ways in which economic evaluations of factorial trials may be conducted, and how these methods affect the results and conclusions. Ignoring interactions introduces bias that could result in adopting a treatment that does not make best use of healthcare resources, while considering all interactions avoids bias but reduces statistical power. We also introduce the concept of the opportunity cost of ignoring interactions as a measure of the bias introduced by not taking account of all interactions. We conclude by offering recommendations for planning, analysing and reporting economic evaluations based on factorial trials, taking increased analysis costs into account. © 2017 The Authors. Statistics in Medicine published by John Wiley & Sons Ltd. PMID:28470760

Green lumber grade yields from factory grade logs of three oak species

Treesearch

Daniel A. Yaussy

1986-01-01

Multivariate regression models were developed to predict green board foot yields for the seven common factory lumber grades processed from white, black, and chestnut oak factory grade logs. These models use the standard log measurements of grade, scaling diameter, log length, and proportion of scaling defect. Any combination of lumber grades (such as 1 Common and...

Photon theory hypothesis about photon tunneling microscope's subwavelength resolution

NASA Astrophysics Data System (ADS)

Zhu, Yanbin; Ma, Junfu

1995-09-01

The foundation for the invention of the photon scanning tunneling microscope (PSTM) are the near field scanning optical microscope, the optical fiber technique, the total internal reflection, high sensitive opto-electronic detecting technique and computer technique etc. Recent research results show the subwavelength resolution of 1 - 3 nm is obtained. How to explain the PSTM has got such high subwavelength resolution? What value is the PSTM's limiting of subwavelength resolution? For resolving these problems this paper presented a photon theory hypothesis about PSTM that is based on the following two basic laws: (1) Photon is not only a carrier bringing energy and optical information, but also is a particle occupied fixed space size. (2) When a photon happened reflection, refraction, scattering, etc., only changed its energy and optical information carried, its particle size doesn't change. g (DOT) pphoton equals constant. Using these two basic laws to PSTM, the `evanescent field' is practically a weak photon distribution field and the detecting fiber tip diameter is practically a `gate' which size controlled the photon numbers into fiber tip. Passing through some calculation and inference, the following three conclusions can be given: (1) Under the PSTM's detection system sensitivity is high enough, the diameter D of detecting fiber tip and the near field detecting distance Z are the two most important factors to decide the subwavelength resolution of PSTM. (2) The limiting of PSTM's resolution will be given upon the conditions of D equals pphoton and Z equals pphoton, where pphoton is one photon size. (2) The final resolution limit R of PSTM will be lim R equals pphoton, D yields pphoton, Z yields pphoton.

Microresonator and associated method for producing and controlling photonic signals with a photonic bandgap delay apparatus

NASA Technical Reports Server (NTRS)

Fork, Richard Lynn (Inventor); Jones, Darryl Keith (Inventor); Keys, Andrew Scott (Inventor)

2000-01-01

By applying a photonic signal to a microresonator that includes a photonic bandgap delay apparatus having a photonic band edge transmission resonance at the frequency of the photonic signal, the microresonator imparts a predetermined delay to the photonic signal. The photonic bandgap delay apparatus also preferably has a photonic band edge transmission resonance bandwidth which is at least as wide as the bandwidth of the photonic signal such that a uniform delay is imparted over the entire bandwidth of the photonic signal. The microresonator also includes a microresonator cavity, typically defined by a pair of switchable mirrors, within which the photonic bandgap delay apparatus is disposed. By requiring the photonic signal to oscillate within the microresonator cavity so as to pass through the photonic bandgap delay apparatus several times, the microresonator can controllably impart an adjustable delay to the photonic signal.

Engineering tolerance to industrially relevant stress factors in yeast cell factories.

PubMed

Deparis, Quinten; Claes, Arne; Foulquié-Moreno, Maria R; Thevelein, Johan M

2017-06-01

The main focus in development of yeast cell factories has generally been on establishing optimal activity of heterologous pathways and further metabolic engineering of the host strain to maximize product yield and titer. Adequate stress tolerance of the host strain has turned out to be another major challenge for obtaining economically viable performance in industrial production. Although general robustness is a universal requirement for industrial microorganisms, production of novel compounds using artificial metabolic pathways presents additional challenges. Many of the bio-based compounds desirable for production by cell factories are highly toxic to the host cells in the titers required for economic viability. Artificial metabolic pathways also turn out to be much more sensitive to stress factors than endogenous pathways, likely because regulation of the latter has been optimized in evolution in myriads of environmental conditions. We discuss different environmental and metabolic stress factors with high relevance for industrial utilization of yeast cell factories and the experimental approaches used to engineer higher stress tolerance. Improving stress tolerance in a predictable manner in yeast cell factories should facilitate their widespread utilization in the bio-based economy and extend the range of products successfully produced in large scale in a sustainable and economically profitable way. © FEMS 2017.

Engineering tolerance to industrially relevant stress factors in yeast cell factories

PubMed Central

Deparis, Quinten; Claes, Arne; Foulquié-Moreno, Maria R.

2017-01-01

Abstract The main focus in development of yeast cell factories has generally been on establishing optimal activity of heterologous pathways and further metabolic engineering of the host strain to maximize product yield and titer. Adequate stress tolerance of the host strain has turned out to be another major challenge for obtaining economically viable performance in industrial production. Although general robustness is a universal requirement for industrial microorganisms, production of novel compounds using artificial metabolic pathways presents additional challenges. Many of the bio-based compounds desirable for production by cell factories are highly toxic to the host cells in the titers required for economic viability. Artificial metabolic pathways also turn out to be much more sensitive to stress factors than endogenous pathways, likely because regulation of the latter has been optimized in evolution in myriads of environmental conditions. We discuss different environmental and metabolic stress factors with high relevance for industrial utilization of yeast cell factories and the experimental approaches used to engineer higher stress tolerance. Improving stress tolerance in a predictable manner in yeast cell factories should facilitate their widespread utilization in the bio-based economy and extend the range of products successfully produced in large scale in a sustainable and economically profitable way. PMID:28586408

Photonic Integrated Circuits

NASA Technical Reports Server (NTRS)

Krainak, Michael; Merritt, Scott

2016-01-01

Integrated photonics generally is the integration of multiple lithographically defined photonic and electronic components and devices (e.g. lasers, detectors, waveguides passive structures, modulators, electronic control and optical interconnects) on a single platform with nanometer-scale feature sizes. The development of photonic integrated circuits permits size, weight, power and cost reductions for spacecraft microprocessors, optical communication, processor buses, advanced data processing, and integrated optic science instrument optical systems, subsystems and components. This is particularly critical for small spacecraft platforms. We will give an overview of some NASA applications for integrated photonics.

Educating photonics engineers

NASA Astrophysics Data System (ADS)

Jessop, Paul E.

2002-05-01

Photonics related industries in Canada have enjoyed remarkable success in the last decade, particularly in the area of fiber optic telecommunications. There is, however, growing concern that a shortage of highly skilled photonics professionals will limit future growth and weaken Canada's competitive position. A recent paper by Nantel and Beda' presents a good summary of the state of photonics in Canada and the projected needs for highly qualified personnel. The recent economic downturn, which has been particularly severe in the photonics sector, has reduced the sense of urgency surrounding the projected shortages of highly qualified personnel. Many individuals who were recently recruited into the photonics industry are now seeking other employment. This should serve as a warning to university educators not to focus their programs too narrowly on specific short term requirements of industry, but to provide graduates with a broad skill set that leaves them positioned to react to changing circumstances. Nevertheless, the critical importance of photonics education and training and the long term prospects in this sector remain unchanged. To meet the future demands for skilled professionals, there is a need for more bachelor's level university programs that include advanced photonics concepts and exposure to state of the art technology.

Dental caries experience in high risk soft drinks factory workers of South India: a comparative study.

PubMed

Kumar, Sandeep; Acharya, Shashidhar; Vasthare, Ramprasad; Singh, Siddharth Kumar; Gupta, Anjali; Debnath, Nitai

2014-01-01

The consumption of soft-drinks has been associated with dental caries development. The aim was to evaluate dental caries experience amongst the workers working in soft-drink industries located in South India and compare it with other factory workers. To evaluate the validity of specific caries index (SCI), which is newer index for caries diagnosis. This was a cross-sectional study carried out among 420 workers (210 in soft-drinks factory and 210 in other factories), in the age group of 20-45 years of Udupi district, Karnataka, India. Index used for clinical examination was decayed, missing, filled surfaces (DMFS) index and SCI. The mean and standard deviation (SD) of decayed surface (5.8 ± 1.8), missing surface (4.3 ± 2) and filled surface (1.94 ± 1.95) and total DMFS score (12.11 ± 3.8) in soft-drinks factory workers were found to be significantly higher than the other factory workers. The total SCI score (mean and SD) was found to be significantly higher in soft-drinks factory workers (5.83 ± 1.80) compared with other factory workers (4.56 ± 1.45). There was a high correlation obtained between SCI score and DMFS score. The regression equation given by DMFS = 1.178 + 1.866 (SCI scores). The caries experience was higher in workers working in soft-drinks factory and this study also showed that specific caries index can be used as a valid index for assessing dental caries experience.

Measuring Single Photons

Science.gov Websites

Explore the World of Particle Physics Measuring Single Photons The web pages that follow presume phenomenon and then return to our study of single photon measurement. Your choices include: These choices University of Colorado. A Java applet by Phillip Warner. Dive right into the single photon pages here

Photon beam position monitor

DOEpatents

Kuzay, T.M.; Shu, D.

1995-02-07

A photon beam position monitor is disclosed for use in the front end of a beamline of a high heat flux and high energy photon source such as a synchrotron radiation storage ring detects and measures the position and, when a pair of such monitors are used in tandem, the slope of a photon beam emanating from an insertion device such as a wiggler or an undulator inserted in the straight sections of the ring. The photon beam position monitor includes a plurality of spaced blades for precisely locating the photon beam, with each blade comprised of chemical vapor deposition (CVD) diamond with an outer metal coating of a photon sensitive metal such as tungsten, molybdenum, etc., which combination emits electrons when a high energy photon beam is incident upon the blade. Two such monitors are contemplated for use in the front end of the beamline, with the two monitors having vertically and horizontally offset detector blades to avoid blade ''shadowing''. Provision is made for aligning the detector blades with the photon beam and limiting detector blade temperature during operation. 18 figs.

Photon beam position monitor

DOEpatents

Kuzay, Tuncer M.; Shu, Deming

1995-01-01

A photon beam position monitor for use in the front end of a beamline of a high heat flux and high energy photon source such as a synchrotron radiation storage ring detects and measures the position and, when a pair of such monitors are used in tandem, the slope of a photon beam emanating from an insertion device such as a wiggler or an undulator inserted in the straight sections of the ring. The photon beam position monitor includes a plurality of spaced blades for precisely locating the photon beam, with each blade comprised of chemical vapor deposition (CVD) diamond with an outer metal coating of a photon sensitive metal such as tungsten, molybdenum, etc., which combination emits electrons when a high energy photon beam is incident upon the blade. Two such monitors are contemplated for use in the front end of the beamline, with the two monitors having vertically and horizontally offset detector blades to avoid blade "shadowing". Provision is made for aligning the detector blades with the photon beam and limiting detector blade temperature during operation.

Gynecologic pain related to occupational stress among female factory workers in Tianjin, China

PubMed Central

Sznajder, Kristin K; Harlow, Siobán D; Burgard, Sarah A; Wang, Yanrang; Han, Cheng; Liu, Jing

2014-01-01

Background: Dysmenorrhea, dyspareunia, and non-cyclic pelvic pain are health concerns for factory workers in China and may be increased by occupational stress. Objectives: To estimate the prevalence and demographic and occupational factors associated with three types of gynecologic pain among female factory workers in Tianjin. Methods: The study included 651 female workers from three factories in Tianjin, China. Logistic regression models were estimated to determine associations between occupational stress and gynecologic pain. Results: Occupational stress including high job strain, exhaustion, and stress related to working conditions was a risk factor for gynecologic pain. High job strain and poor job security were associated with an increased risk for dysmenorrhea. Compulsory overtime and exhaustion were associated with increased non-cyclic pelvic pain. Working overtime and exhaustion were associated with increased dyspareunia. Conclusions: As China’s population of female factory workers grows, research on the reproductive health of this population is essential. PMID:24804338

Production of fatty acid-derived oleochemicals and biofuels by synthetic yeast cell factories

PubMed Central

Zhou, Yongjin J.; Buijs, Nicolaas A.; Zhu, Zhiwei; Qin, Jiufu; Siewers, Verena; Nielsen, Jens

2016-01-01

Sustainable production of oleochemicals requires establishment of cell factory platform strains. The yeast Saccharomyces cerevisiae is an attractive cell factory as new strains can be rapidly implemented into existing infrastructures such as bioethanol production plants. Here we show high-level production of free fatty acids (FFAs) in a yeast cell factory, and the production of alkanes and fatty alcohols from its descendants. The engineered strain produces up to 10.4 g l−1 of FFAs, which is the highest reported titre to date. Furthermore, through screening of specific pathway enzymes, endogenous alcohol dehydrogenases and aldehyde reductases, we reconstruct efficient pathways for conversion of fatty acids to alkanes (0.8 mg l−1) and fatty alcohols (1.5 g l−1), to our knowledge the highest titres reported in S. cerevisiae. This should facilitate the construction of yeast cell factories for production of fatty acids derived products and even aldehyde-derived chemicals of high value. PMID:27222209

Photonic-powered cable assembly

DOEpatents

Sanderson, Stephen N.; Appel, Titus James; Wrye, IV, Walter C.

2013-01-22

A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

Photonic-powered cable assembly

DOEpatents

Sanderson, Stephen N; Appel, Titus James; Wrye, IV, Walter C

2014-06-24

A photonic-cable assembly includes a power source cable connector ("PSCC") coupled to a power receive cable connector ("PRCC") via a fiber cable. The PSCC electrically connects to a first electronic device and houses a photonic power source and an optical data transmitter. The fiber cable includes an optical transmit data path coupled to the optical data transmitter, an optical power path coupled to the photonic power source, and an optical feedback path coupled to provide feedback control to the photonic power source. The PRCC electrically connects to a second electronic device and houses an optical data receiver coupled to the optical transmit data path, a feedback controller coupled to the optical feedback path to control the photonic power source, and a photonic power converter coupled to the optical power path to convert photonic energy received over the optical power path to electrical energy to power components of the PRCC.

A single-photon fluorescence and multi-photon spectroscopic study of atherosclerotic lesions

NASA Astrophysics Data System (ADS)

Smith, Michael S. D.; Ko, Alex C. T.; Ridsdale, Andrew; Schattka, Bernie; Pegoraro, Adrian; Hewko, Mark D.; Shiomi, Masashi; Stolow, Albert; Sowa, Michael G.

2009-06-01

In this study we compare the single-photon autofluorescence and multi-photon emission spectra obtained from the luminal surface of healthy segments of artery with segments where there are early atherosclerotic lesions. Arterial tissue was harvested from atherosclerosis-prone WHHL-MI rabbits (Watanabe heritable hyperlipidemic rabbit-myocardial infarction), an animal model which mimics spontaneous myocardial infarction in humans. Single photon fluorescence emission spectra of samples were acquired using a simple spectrofluorometer set-up with 400 nm excitation. Samples were also investigated using a home built multi-photon microscope based on a Ti:sapphire femto-second oscillator. The excitation wavelength was set at 800 nm with a ~100 femto-second pulse width. Epi-multi-photon spectroscopic signals were collected through a fibre-optics coupled spectrometer. While the single-photon fluorescence spectra of atherosclerotic lesions show minimal spectroscopic difference from those of healthy arterial tissue, the multi-photon spectra collected from atherosclerotic lesions show marked changes in the relative intensity of two-photon excited fluorescence (TPEF) and second-harmonic generation (SHG) signals when compared with those from healthy arterial tissue. The observed sharp increase of the relative SHG signal intensity in a plaque is in agreement with the known pathology of early lesions which have increased collagen content.

Photon-triggered nanowire transistors

NASA Astrophysics Data System (ADS)

Kim, Jungkil; Lee, Hoo-Cheol; Kim, Kyoung-Ho; Hwang, Min-Soo; Park, Jin-Sung; Lee, Jung Min; So, Jae-Pil; Choi, Jae-Hyuck; Kwon, Soon-Hong; Barrelet, Carl J.; Park, Hong-Gyu

2017-10-01

Photon-triggered electronic circuits have been a long-standing goal of photonics. Recent demonstrations include either all-optical transistors in which photons control other photons or phototransistors with the gate response tuned or enhanced by photons. However, only a few studies report on devices in which electronic currents are optically switched and amplified without an electrical gate. Here we show photon-triggered nanowire (NW) transistors, photon-triggered NW logic gates and a single NW photodetection system. NWs are synthesized with long crystalline silicon (CSi) segments connected by short porous silicon (PSi) segments. In a fabricated device, the electrical contacts on both ends of the NW are connected to a single PSi segment in the middle. Exposing the PSi segment to light triggers a current in the NW with a high on/off ratio of >8 × 106. A device that contains two PSi segments along the NW can be triggered using two independent optical input signals. Using localized pump lasers, we demonstrate photon-triggered logic gates including AND, OR and NAND gates. A photon-triggered NW transistor of diameter 25 nm with a single 100 nm PSi segment requires less than 300 pW of power. Furthermore, we take advantage of the high photosensitivity and fabricate a submicrometre-resolution photodetection system. Photon-triggered transistors offer a new venue towards multifunctional device applications such as programmable logic elements and ultrasensitive photodetectors.

Photon-triggered nanowire transistors.

PubMed

Kim, Jungkil; Lee, Hoo-Cheol; Kim, Kyoung-Ho; Hwang, Min-Soo; Park, Jin-Sung; Lee, Jung Min; So, Jae-Pil; Choi, Jae-Hyuck; Kwon, Soon-Hong; Barrelet, Carl J; Park, Hong-Gyu

2017-10-01

Photon-triggered electronic circuits have been a long-standing goal of photonics. Recent demonstrations include either all-optical transistors in which photons control other photons or phototransistors with the gate response tuned or enhanced by photons. However, only a few studies report on devices in which electronic currents are optically switched and amplified without an electrical gate. Here we show photon-triggered nanowire (NW) transistors, photon-triggered NW logic gates and a single NW photodetection system. NWs are synthesized with long crystalline silicon (CSi) segments connected by short porous silicon (PSi) segments. In a fabricated device, the electrical contacts on both ends of the NW are connected to a single PSi segment in the middle. Exposing the PSi segment to light triggers a current in the NW with a high on/off ratio of >8 × 10 6 . A device that contains two PSi segments along the NW can be triggered using two independent optical input signals. Using localized pump lasers, we demonstrate photon-triggered logic gates including AND, OR and NAND gates. A photon-triggered NW transistor of diameter 25 nm with a single 100 nm PSi segment requires less than 300 pW of power. Furthermore, we take advantage of the high photosensitivity and fabricate a submicrometre-resolution photodetection system. Photon-triggered transistors offer a new venue towards multifunctional device applications such as programmable logic elements and ultrasensitive photodetectors.

Quasiperiodic one-dimensional photonic crystals with adjustable multiple photonic bandgaps.

PubMed

Vyunishev, Andrey M; Pankin, Pavel S; Svyakhovskiy, Sergey E; Timofeev, Ivan V; Vetrov, Stepan Ya

2017-09-15

We propose an elegant approach to produce photonic bandgap (PBG) structures with multiple photonic bandgaps by constructing quasiperiodic photonic crystals (QPPCs) composed of a superposition of photonic lattices with different periods. Generally, QPPC structures exhibit both aperiodicity and multiple PBGs due to their long-range order. They are described by a simple analytical expression, instead of quasiperiodic tiling approaches based on substitution rules. Here we describe the optical properties of QPPCs exhibiting two PBGs that can be tuned independently. PBG interband spacing and its depth can be varied by choosing appropriate reciprocal lattice vectors and their amplitudes. These effects are confirmed by the proof-of-concept measurements made for the porous silicon-based QPPC of the appropriate design.

This Furniture Program Has Its Own Factory

ERIC Educational Resources Information Center

Bliss, Robert E.

1975-01-01

Catawba Valley Technical Institute, located in Hickory, North Carolina where 45 percent of the population is employed by the furniture industry, presently offers two associate degree and two vocational diploma programs. A campus furniture factory, close institute and industry cooperation, and extensive in-plant training have contributed to the…

Effect of filling factor on photonic bandgap of chalcogenide photonic crystal

NASA Astrophysics Data System (ADS)

Singh, Rajpal; Suthar, B.; Bhargava, A.

2018-05-01

In the present work, the photonic band structure of 1-D chalcogenide photonic crystal of As2S3/air multilayered structure is calculated using the plane wave expansion method. The study is extended to investigate the effect of filling factor on the photonic bandgap. The increase of bandgap is explained in the study.

Training Workers for the Factory of the Future.

ERIC Educational Resources Information Center

Clancy, J. Anthony

1989-01-01

In the factory of the future, emphasis on quality and increased productivity creates a competitive advantage. People and computers work together in all major activities. Training is a major factor in creating that competitive advantage. (JOW)

Bulgar Factories (Trading Posts) in the Kama River Area as a Factor of Adjustment to Feudalism

ERIC Educational Resources Information Center

Krylasova, Natalia B.; Belavin, Andrei M.; Podosenova, Yulia A.

2016-01-01

At the start of the 2nd ML AD a number of trading posts, or factories, emerged in the Cis-Ural region with participation of Bulgar handicraftsmen and merchants. They were townships populated by various ethnic groups. Several centuries later similar factories were set up by natives of the Cis-Ural region in Western Siberia. These factories have…

Front End for a neutrino factory or muon collider

NASA Astrophysics Data System (ADS)

Neuffer, D.; Snopok, P.; Alexahin, Y.

2017-11-01

A neutrino factory or muon collider requires the capture and cooling of a large number of muons. Scenarios for capture, bunching, phase-energy rotation and initial cooling of μ 's produced from a proton source target have been developed, initially for neutrino factory scenarios. They require a drift section from the target, a bunching section and a varphi -δ E rotation section leading into the cooling channel. Important concerns are rf limitations within the focusing magnetic fields and large losses in the transport. The currently preferred cooling channel design is an "HFOFO Snake" configuration that cools both μ+ and μ- transversely and longitudinally. The status of the design is presented and variations are discussed.

Photonic Crystal Fiber Based Entangled Photon Sources

DTIC Science & Technology

2014-03-01

5 Figure 2: The diagram of the counter- propagating scheme. FP: fiber port ( free - space to fiber). PBS: polarization beam splitter. LP: Linear... entangled photon -pairs using the highly nonlinear fiber in a counter- propagating scheme (CPS). With the HNLF at room temperature, we obtain a... propagating scheme for generating polarization entangled photon pairs at telecom wavelengths. We use 10 m of highly nonlinear fiber. We measure a

Photonic crystal nanocavity assisted rejection ratio tunable notch microwave photonic filter

NASA Astrophysics Data System (ADS)

Long, Yun; Xia, Jinsong; Zhang, Yong; Dong, Jianji; Wang, Jian

2017-01-01

Driven by the increasing demand on handing microwave signals with compact device, low power consumption, high efficiency and high reliability, it is highly desired to generate, distribute, and process microwave signals using photonic integrated circuits. Silicon photonics offers a promising platform facilitating ultracompact microwave photonic signal processing assisted by silicon nanophotonic devices. In this paper, we propose, theoretically analyze and experimentally demonstrate a simple scheme to realize ultracompact rejection ratio tunable notch microwave photonic filter (MPF) based on a silicon photonic crystal (PhC) nanocavity with fixed extinction ratio. Using a conventional modulation scheme with only a single phase modulator (PM), the rejection ratio of the presented MPF can be tuned from about 10 dB to beyond 60 dB. Moreover, the central frequency tunable operation in the high rejection ratio region is also demonstrated in the experiment.

Photonic crystal nanocavity assisted rejection ratio tunable notch microwave photonic filter

PubMed Central

Long, Yun; Xia, Jinsong; Zhang, Yong; Dong, Jianji; Wang, Jian

2017-01-01

Driven by the increasing demand on handing microwave signals with compact device, low power consumption, high efficiency and high reliability, it is highly desired to generate, distribute, and process microwave signals using photonic integrated circuits. Silicon photonics offers a promising platform facilitating ultracompact microwave photonic signal processing assisted by silicon nanophotonic devices. In this paper, we propose, theoretically analyze and experimentally demonstrate a simple scheme to realize ultracompact rejection ratio tunable notch microwave photonic filter (MPF) based on a silicon photonic crystal (PhC) nanocavity with fixed extinction ratio. Using a conventional modulation scheme with only a single phase modulator (PM), the rejection ratio of the presented MPF can be tuned from about 10 dB to beyond 60 dB. Moreover, the central frequency tunable operation in the high rejection ratio region is also demonstrated in the experiment. PMID:28067332

Photonic crystal nanocavity assisted rejection ratio tunable notch microwave photonic filter.

PubMed

Long, Yun; Xia, Jinsong; Zhang, Yong; Dong, Jianji; Wang, Jian

2017-01-09

Driven by the increasing demand on handing microwave signals with compact device, low power consumption, high efficiency and high reliability, it is highly desired to generate, distribute, and process microwave signals using photonic integrated circuits. Silicon photonics offers a promising platform facilitating ultracompact microwave photonic signal processing assisted by silicon nanophotonic devices. In this paper, we propose, theoretically analyze and experimentally demonstrate a simple scheme to realize ultracompact rejection ratio tunable notch microwave photonic filter (MPF) based on a silicon photonic crystal (PhC) nanocavity with fixed extinction ratio. Using a conventional modulation scheme with only a single phase modulator (PM), the rejection ratio of the presented MPF can be tuned from about 10 dB to beyond 60 dB. Moreover, the central frequency tunable operation in the high rejection ratio region is also demonstrated in the experiment.

Factorial validity of the Movement Assessment Battery for Children-2 (age band 2).

PubMed

Wagner, Matthias Oliver; Kastner, Julia; Petermann, Franz; Bös, Klaus

2011-01-01

The Movement Assessment Battery for Children-2 (M-ABC-2) is one of the most commonly used tests for the diagnosis of specific developmental disorders of motor function (F82). The M-ABC-2 comprises eight subtests per age band (AB) that are assigned to three dimensions: manual dexterity, aiming and catching, and balance. However, while previous exploratory findings suggested the correctness of the assumption of factorial validity, there is no empirical evidence that the M-ABC-2 subtests allow for a valid reproduction of the postulated factorial structure. The purpose of this study was to empirically confirm the factorial validity of the M-ABC-2. The German normative sample of AB2 (7-10 years; N=323) was used as the study sample for the empirical analyses. Confirmatory factor analysis was used to verify the factorial validity of the M-ABC-2 (AB2). The incremental fit indices (χ2=28.675; df=17; Bollen-Stine p value=0.318; RMSEA=0.046 [0.011-0.075]; SRMR=0.038; CFI=0.960) provided evidence for the factorial validity of the M-ABC-2 (AB2). However, because of a lack of empirical verification for convergent and discriminant validity, there is still no evidence that F82 can be diagnosed using M-ABC-2 (AB2). Copyright © 2010 Elsevier Ltd. All rights reserved.

Peak expiratory flow rate of children working in lock factories.

PubMed

Singhal, S; Singhal, A; Singh, P N; Agarwal, D K; Gulati, R

2006-01-01

Peak expiratory flow rate (PEFR) of 106 children working in different units of lock factory was measured and compared with age and sex matched control group of same socio-economic status children. All the children worked for about ten hours per day. It was observed that there was a significant decrease in PEFR of children working in the different units of lock factories i.e. Hand press, Polishing, Lock fitting, Lock packing units as compared to control group (P>0.001). The reduction percentage of PEFR was maximum in children working in polishing unit (25.48%).

Electro-optic routing of photons from a single quantum dot in photonic integrated circuits

NASA Astrophysics Data System (ADS)

Midolo, Leonardo; Hansen, Sofie L.; Zhang, Weili; Papon, Camille; Schott, Rüdiger; Ludwig, Arne; Wieck, Andreas D.; Lodahl, Peter; Stobbe, Søren

2017-12-01

Recent breakthroughs in solid-state photonic quantum technologies enable generating and detecting single photons with near-unity efficiency as required for a range of photonic quantum technologies. The lack of methods to simultaneously generate and control photons within the same chip, however, has formed a main obstacle to achieving efficient multi-qubit gates and to harness the advantages of chip-scale quantum photonics. Here we propose and demonstrate an integrated voltage-controlled phase shifter based on the electro-optic effect in suspended photonic waveguides with embedded quantum emitters. The phase control allows building a compact Mach-Zehnder interferometer with two orthogonal arms, taking advantage of the anisotropic electro-optic response in gallium arsenide. Photons emitted by single self-assembled quantum dots can be actively routed into the two outputs of the interferometer. These results, together with the observed sub-microsecond response time, constitute a significant step towards chip-scale single-photon-source de-multiplexing, fiber-loop boson sampling, and linear optical quantum computing.

Bioretention Systems: Partial Factorial Designs for Nitrate Removal

EPA Science Inventory

Changes in nutrient loadings are monitored by introducing captured stormwater runoff into eight outdoor rain gardens at EPA’s Urban Water Research Facility in Edison, New Jersey scaled for residential and urban landscapes. The partial factorial design includes non-vegetated meso...

Survey of Nitrate Ion Concentrations in Vegetables Cultivated in Plant Factories: Comparison with Open-Culture Vegetables.

PubMed

Oka, Yuka; Hirayama, Izumi; Yoshikawa, Mitsuhide; Yokoyama, Tomoko; Iida, Kenji; Iwakoshi, Katsushi; Suzuki, Ayana; Yanagihara, Midori; Segawa, Yukino; Kukimoto, Sonomi; Hamada, Humika; Matsuzawa, Satomi; Tabata, Setsuko; Sasamoto, Takeo

2017-01-01

A survey of nitrate-ion concentrations in plant-factory-cultured leafy vegetables was conducted. 344 samples of twenty-one varieties of raw leafy vegetables were examined using HPLC. The nitrate-ion concentrations in plant-factory-cultured leafy vegetables were found to be LOD-6,800 mg/kg. Furthermore, the average concentration values varied among different leafy vegetables. The average values for plant-factory-cultured leafy vegetables were higher than those of open-cultured leafy vegetables reported in previous studies, such as the values listed in the Standard Tables of Food Composition in Japan- 2015 - (Seventh revised edition). For some plant-factory-cultured leafy vegetables, such as salad spinach, the average values were above the maximum permissible levels of nitrate concentration in EC No 1258/2011; however, even when these plant-factory-cultured vegetables were routinely eaten, the intake of nitrate ions in humans did not exceed the ADI.

Enhanced photon-phonon cross-Kerr nonlinearity with two-photon driving.

PubMed

Yin, Tai-Shuang; Lü, Xin-You; Wan, Liang-Liang; Bin, Shang-Wu; Wu, Ying

2018-05-01

We propose a scheme to significantly enhance the cross-Kerr (CK) nonlinearity between photons and phonons in a quadratically coupled optomechanical system (OMS) with two-photon driving. This CK nonlinear enhancement originates from the parametric-driving-induced squeezing and the underlying nonlinear optomechanical interaction. Moreover, the noise of the squeezed mode can be suppressed completely by introducing a squeezed vacuum reservoir. As a result of this dramatic nonlinear enhancement and the suppressed noise, we demonstrate the feasibility of the quantum nondemolition measurement of the phonon number in an originally weak coupled OMS. In addition, the photon-phonon blockade phenomenon is also investigated in this regime, which allows for performing manipulations between photons and phonons. This Letter offers a promising route towards the potential application for the OMS in quantum information processing and quantum networks.

Entangled, guided photon generation in (1+1)-dimensional photonic crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sciscione, L.; Centini, M.; Sibilia, C.

A scheme based on photonic crystal technology is proposed as an ultrabright source of entangled photons on a miniaturized scale. The geometry consists of a multilayer microcavity, excited by a resonant pump frequency, such that the emitted photons are guided transversally to the direction of the incident pump. The entanglement occurs in direction, frequency, and polarization, and the bandwidth of the emitted photons is of the order of 1 nm. We propose a feasible design based on Al{sub 0.3}Ga{sub 0.7}As/Al{sub 2}O{sub 3} structures and predict an emission rate 10{sup 5} pairs per second with 100 mW pump power. These resultsmore » are promising for realization of chip and future quantum computer applications.« less

Construction of Escherichia Coli Cell Factories for Production of Organic Acids and Alcohols.

PubMed

Liu, Pingping; Zhu, Xinna; Tan, Zaigao; Zhang, Xueli; Ma, Yanhe

2016-01-01

Production of bulk chemicals from renewable biomass has been proved to be sustainable and environmentally friendly. Escherichia coli is the most commonly used host strain for constructing cell factories for production of bulk chemicals since it has clear physiological and genetic characteristics, grows fast in minimal salts medium, uses a wide range of substrates, and can be genetically modified easily. With the development of metabolic engineering, systems biology, and synthetic biology, a technology platform has been established to construct E. coli cell factories for bulk chemicals production. In this chapter, we will introduce this technology platform, as well as E. coli cell factories successfully constructed for production of organic acids and alcohols.

Front End for a neutrino factory or muon collider

DOE PAGES

Neuffer, David; Snopok, Pavel; Alexahin, Yuri

2017-11-30

A neutrino factory or muon collider requires the capture and cooling of a large number of muons. Scenarios for capture, bunching, phase-energy rotation and initial cooling of μ’s produced from a proton source target have been developed, initially for neutrino factory scenarios. They require a drift section from the target, a bunching section and a Φ-δE rotation section leading into the cooling channel. Important concerns are rf limitations within the focusing magnetic fields and large losses in the transport. The currently preferred cooling channel design is an “HFOFO Snake” configuration that cools both μ + and μ - transversely andmore » longitudinally. Finally, the status of the design is presented and variations are discussed.« less

Divergent response of the neritic carbonate factory to environmental changes during the Early Bajocian Event

NASA Astrophysics Data System (ADS)

Bodin, Stephane; Hönig, Martin; Krencker, Francois-Nicolas; Danisch, Jan; Kabiri, Lahcen

2017-04-01

The Early Bajocian witnessed a global environmental perturbation, characterized by faunal and floral turnovers and a positive carbon isotope excursion. In Italy, this environmental perturbation coincided with an eutrophication event and a carbonate crisis, but this has so far not been adequately reported from other settings, leaving doubt about the extent and nature of these phenomena. Here, we are reporting on an extensive neritic carbonate factory demise that occurs in the upper Lower Bajocian of the Central High Atlas of Morocco, more precisely in the upper Propinquans - lower Humphriesianum Zones. This demise coincided with the acme of the global carbon isotope perturbation, recorded by a 3‰ positive carbon isotope excursion in the bulk organic matter of Morocco. Recovery of the neritic carbonate system occurs during the Early to Late Bajocian transition. The duration of the neritic carbonate factory demise was therefore in the order of 1 Myr. Furthermore, we observe that the Lower Bajocian of Morocco is relatively enriched in arenitic siliciclastic deposits, suggesting increased weathering and nutrient levels along the northwestern margin of Africa during the Early Bajocian. However, comparison with neighboring European basins highlights the non-uniqueness and different timing of the response of shallow-water carbonates to the Early Bajocian environmental perturbations, as some regions present no sign of carbonate factory crisis. Hence, we postulate that local factors were important in mediating the response of neritic carbonate factories to this global environmental perturbation. We notably highlight the role of large Early Bajocian sea-level fluctuation as a trigger for carbonate factory change and demise in Morocco. Indeed, in the Central High Atlas Basin, transgressive intervals are seeing the development of a mud-dominated carbonate factory whereas regressive intervals are associated with grain-dominated carbonate factory. We speculate that the

Thermalization of a two-dimensional photonic gas in a `white wall' photon box

NASA Astrophysics Data System (ADS)

Klaers, Jan; Vewinger, Frank; Weitz, Martin

2010-07-01

Bose-Einstein condensation, the macroscopic accumulation of bosonic particles in the energetic ground state below a critical temperature, has been demonstrated in several physical systems. The perhaps best known example of a bosonic gas, blackbody radiation, however exhibits no Bose-Einstein condensation at low temperatures. Instead of collectively occupying the lowest energy mode, the photons disappear in the cavity walls when the temperature is lowered-corresponding to a vanishing chemical potential. Here we report on evidence for a thermalized two-dimensional photon gas with a freely adjustable chemical potential. Our experiment is based on a dye-filled optical microresonator, acting as a `white wall' box for photons. Thermalization is achieved in a photon-number-conserving way by photon scattering off the dye molecules, and the cavity mirrors provide both an effective photon mass and a confining potential-key prerequisites for the Bose-Einstein condensation of photons. As a striking example of the unusual system properties, we demonstrate a yet unobserved light concentration effect into the centre of the confining potential, an effect with prospects for increasing the efficiency of diffuse solar light collection.

Recyclable amplification for single-photon entanglement from photon loss and decoherence

NASA Astrophysics Data System (ADS)

Zhou, Lan; Chen, Ling-Quan; Zhong, Wei; Sheng, Yu-Bo

2018-01-01

We put forward a highly efficient recyclable single-photon assisted amplification protocol, which can protect single-photon entanglement (SPE) from photon loss and decoherence. Making use of quantum nondemolition detection gates constructed with the help of cross-Kerr nonlinearity, our protocol has some attractive advantages. First, the parties can recover less-entangled SPE to be maximally entangled SPE, and reduce photon loss simultaneously. Second, if the protocol fails, the parties can repeat the protocol to reuse some discarded items, which can increase the success probability. Third, when the protocol is successful, they can similarly repeat the protocol to further increase the fidelity of the SPE. Thereby, our protocol provides a possible way to obtain high entanglement, high fidelity and high success probability simultaneously. In particular, our protocol shows higher success probability in the practical high photon loss channel. Based on the above features, our amplification protocol has potential for future application in long-distance quantum communication.

EDITORIAL: TaCoNa-Photonics 2008 TaCoNa-Photonics 2008

NASA Astrophysics Data System (ADS)

Chigrin, Dmitry N.; Busch, Kurt; Lavrinenko, Andrei V.

2009-11-01

This special section on theoretical and computational nano-photonics features papers presented at the first International Workshop on Theoretical and Computational Nano-Photonics (TaCoNa-Photonics 2008) held in Bad Honnef, Germany, 3-5 December 2008. The workshop covered a broad range of topics related to current developments and achievements in this interdisciplinary area of research. Since the late 1960s, the word `photonics' has been understood as the science of generating, controlling, and detecting light. Nowadays, a routine fabrication of complex structures with micro- and nano-scale dimensions opens up many new and exciting possibilities in photonics. The science of generating, routing and detecting light in micro- and nano-structured matter, `nano-photonics', is becoming more important both in research and technology and offers many promising applications. The inherently sub-wavelength character of the structures that nano-photonics deals with challenges modern theoretical and computational physics and engineering with many nontrivial questions: Up to what length-scale can one use a macroscopic phenomenological description of matter? Where is the interface between the classical and quantum description of light in nano-scale structures? How can one combine different physical systems, different time- and length-scales in a single computational model? How can one engineer nano-structured materials in order to achieve the desired optical properties for particular applications? Any attempt at answering these kinds of questions is impossible without the joint efforts of physicists, engineers, applied mathematicians and programmers. This is the reason why the major goal of the TaCoNa-Photonics workshops is to provide a forum where theoreticians and specialists in numerical methods from all branches of physics, engineering sciences and mathematics can compare their results, report on novel results and breakthroughs, and discuss new challenges ahead. In order to

Unilateral pseudogynecomastia: an occupational hazard in manual metal-pressing factories?

PubMed

Spyropoulou, Georgia-Alexandra; Karamatsoukis, Stavros; Foroglou, Pericles

2011-04-01

Five cases of unilateral occupation-related pseudogynecomastia are presented. All the patients in these cases worked in the same metal-pressing factory. One patient with grade 4 unilateral gynecomastia in the right breast presented to the authors' outpatient department asking persistently for surgery. He also reported that all his male colleagues working in the same business (a total of 5) had different degrees of unilateral gynecomastia. Their line of work involved holding a long round rod under the axilla and then pressing the distal end of it firmly against a spinning metal plate. The patient underwent a superior pedicle breast reduction, with 1,800 ml of tissue removed from his right breast. Unfortunately, the patient experienced partial nipple loss. However, he was satisfied with the final result, and good symmetry was achieved. All five patients who worked in the same metal-pressing factory presented with unilateral gynecomastia and were examined in our department. Their average age was 51.4 years. All the patients had normal hormonal and biochemical status, and the results of screening for toxins and heavy metal exposure were negative. All the patients were heavy smokers. At examination, none of the patients had nipple discharge or retraction, skin changes, galactorrhea, or lymphadenopathy. Examination showed one patient with grade 4, three patients had grade 2, and one patient with grade 1 unilateral gynecomastia. The authors believe that gynecomastia may be considered an occupational risk in analogous metal-pressing factories because all the workers in this factory presented with some degree of unilateral gynecomastia. However, they emphasize that this may simply be an observational phenomenon without a true cause and effect relationship.

Collimator-free photon tomography

DOEpatents

Dilmanian, F. Avraham; Barbour, Randall L.

1998-10-06

A method of uncollimated single photon emission computed tomography includes administering a radioisotope to a patient for producing gamma ray photons from a source inside the patient. Emissivity of the photons is measured externally of the patient with an uncollimated gamma camera at a plurality of measurement positions surrounding the patient for obtaining corresponding energy spectrums thereat. Photon emissivity at the plurality of measurement positions is predicted using an initial prediction of an image of the source. The predicted and measured photon emissivities are compared to obtain differences therebetween. Prediction and comparison is iterated by updating the image prediction until the differences are below a threshold for obtaining a final prediction of the source image.

Collimator-free photon tomography

DOEpatents

Dilmanian, F.A.; Barbour, R.L.

1998-10-06

A method of uncollimated single photon emission computed tomography includes administering a radioisotope to a patient for producing gamma ray photons from a source inside the patient. Emissivity of the photons is measured externally of the patient with an uncollimated gamma camera at a plurality of measurement positions surrounding the patient for obtaining corresponding energy spectrums thereat. Photon emissivity at the plurality of measurement positions is predicted using an initial prediction of an image of the source. The predicted and measured photon emissivities are compared to obtain differences therebetween. Prediction and comparison is iterated by updating the image prediction until the differences are below a threshold for obtaining a final prediction of the source image. 6 figs.

Nonlinear Photonics 2014: introduction.

PubMed

Akhmediev, N; Kartashov, Yaroslav

2015-01-12

International Conference "Nonlinear Photonics-2014" took place in Barcelona, Spain on July 27-31, 2014. It was a part of the "Advanced Photonics Congress" which is becoming a traditional notable event in the world of photonics. The current focus issue of Optics Express contains contributions from the participants of the Conference and the Congress. The articles in this focus issue by no means represent the total number of the congress contributions (around 400). However, it demonstrates wide range of topics covered at the event. The next conference of this series is to be held in 2016 in Australia, which is the home of many researchers working in the field of photonics in general and nonlinear photonics in particular.

gPhoton: Time-tagged GALEX photon events analysis tools

NASA Astrophysics Data System (ADS)

Million, Chase C.; Fleming, S. W.; Shiao, B.; Loyd, P.; Seibert, M.; Smith, M.

2016-03-01

Written in Python, gPhoton calibrates and sky-projects the ~1.1 trillion ultraviolet photon events detected by the microchannel plates on the Galaxy Evolution Explorer Spacecraft (GALEX), archives these events in a publicly accessible database at the Mikulski Archive for Space Telescopes (MAST), and provides tools for working with the database to extract scientific results, particularly over short time domains. The software includes a re-implementation of core functionality of the GALEX mission calibration pipeline to produce photon list files from raw spacecraft data as well as a suite of command line tools to generate calibrated light curves, images, and movies from the MAST database.

Photonic Paint Developed with Metallic Three-Dimensional Photonic Crystals

PubMed Central

Sun, Po; Williams, John D.

2012-01-01

This work details the design and simulation of an inconspicuous photonic paint that can be applied onto an object for anticounterfeit and tag, track, and locate (TTL) applications. The paint consists of three-dimensional metallic tilted woodpile photonic crystals embedded into a visible and infrared transparent polymer film, which can be applied to almost any surface. The tilted woodpile photonic crystals are designed with a specific pass band detectable at nearly all incident angles of light. When painted onto a surface, these crystals provide a unique reflective infra-red optical signature that can be easily observed and recorded to verify the location or contents of a package.

Self-assembled tunable photonic hyper-crystals

PubMed Central

Smolyaninova, Vera N.; Yost, Bradley; Lahneman, David; Narimanov, Evgenii E.; Smolyaninov, Igor I.

2014-01-01

We demonstrate a novel artificial optical material, the “photonic hyper-crystal”, which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing. PMID:25027947

Self-assembled tunable photonic hyper-crystals.

PubMed

Smolyaninova, Vera N; Yost, Bradley; Lahneman, David; Narimanov, Evgenii E; Smolyaninov, Igor I

2014-07-16

We demonstrate a novel artificial optical material, the "photonic hyper-crystal", which combines the most interesting features of hyperbolic metamaterials and photonic crystals. Similar to hyperbolic metamaterials, photonic hyper-crystals exhibit broadband divergence in their photonic density of states due to the lack of usual diffraction limit on the photon wave vector. On the other hand, similar to photonic crystals, hyperbolic dispersion law of extraordinary photons is modulated by forbidden gaps near the boundaries of photonic Brillouin zones. Three dimensional self-assembly of photonic hyper-crystals has been achieved by application of external magnetic field to a cobalt nanoparticle-based ferrofluid. Unique spectral properties of photonic hyper-crystals lead to extreme sensitivity of the material to monolayer coatings of cobalt nanoparticles, which should find numerous applications in biological and chemical sensing.

Hybrid Photon-Plasmon Coupling and Ultrafast Control of Nanoantennas on a Silicon Photonic Chip.

PubMed

Chen, Bigeng; Bruck, Roman; Traviss, Daniel; Khokhar, Ali Z; Reynolds, Scott; Thomson, David J; Mashanovich, Goran Z; Reed, Graham T; Muskens, Otto L

2018-01-10

Hybrid integration of nanoplasmonic devices with silicon photonic circuits holds promise for a range of applications in on-chip sensing, field-enhanced and nonlinear spectroscopy, and integrated nanophotonic switches. Here, we demonstrate a new regime of photon-plasmon coupling by combining a silicon photonic resonator with plasmonic nanoantennas. Using principles from coherent perfect absorption, we make use of standing-wave light fields to maximize the photon-plasmon interaction strength. Precise placement of the broadband antennas with respect to the narrowband photonic racetrack modes results in controlled hybridization of only a subset of these modes. By combining antennas into groups of radiating dipoles with opposite phase, far-field scattering is effectively suppressed. We achieve ultrafast tuning of photon-plasmon hybridization including reconfigurable routing of the standing-wave input between two output ports. Hybrid photonic-plasmonic resonators provide conceptually new approaches for on-chip integrated nanophotonic devices.

Counterfactual Rydberg gate for photons

NASA Astrophysics Data System (ADS)

Garcia-Escartin, Juan Carlos; Chamorro-Posada, Pedro

2012-03-01

Quantum computation with photons requires efficient two-photon gates. We put forward a two-photon entangling gate which uses an intermediate atomic system. The system includes a single Rydberg atom which can switch on and off photon absorption in an ensemble using the dipole blockade. The gate is based in a counterfactual protocol. The mere possibility of an absorption that can only occur with a vanishing probability steers the photons to the desired final state.

A factory concept for processing and manufacturing with lunar material

NASA Technical Reports Server (NTRS)

Driggers, G. W.

1977-01-01

A conceptual design for an orbital factory sized to process 1.5 million metric tons per year of raw lunar fines into 0.3 million metric tons of manufacturing materials is presented. A conservative approach involving application of present earth-based technology leads to a design devoid of new inventions. Earth based counterparts to the factory machinery were used to generate subsystem masses and lumped parameters for volume and mass estimates. The results are considered to be conservative since technologies more advanced than those assumed are presently available in many areas. Some attributes of potential space processing technologies applied to material refinement and component manufacture are discussed.

Single-Photon Nanoantennas

PubMed Central

2017-01-01

Single-photon nanoantennas are broadband strongly scattering nanostructures placed in the near field of a single quantum emitter, with the goal to enhance the coupling between the emitter and far-field radiation channels. Recently, great strides have been made in the use of nanoantennas to realize fluorescence brightness enhancements, and Purcell enhancements, of several orders of magnitude. This perspective reviews the key figures of merit by which single-photon nanoantenna performance is quantified and the recent advances in measuring these metrics unambiguously. Next, this perspective discusses what the state of the art is in terms of fluoresent brightness enhancements, Purcell factors, and directivity control on the level of single photons. Finally, I discuss future challenges for single-photon nanoantennas. PMID:29354664

Photonic crystal surface-emitting lasers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chua, Song Liang; Lu, Ling; Soljacic, Marin

2015-06-23

A photonic-crystal surface-emitting laser (PCSEL) includes a gain medium electromagnetically coupled to a photonic crystal whose energy band structure exhibits a Dirac cone of linear dispersion at the center of the photonic crystal's Brillouin zone. This Dirac cone's vertex is called a Dirac point; because it is at the Brillouin zone center, it is called an accidental Dirac point. Tuning the photonic crystal's band structure (e.g., by changing the photonic crystal's dimensions or refractive index) to exhibit an accidental Dirac point increases the photonic crystal's mode spacing by orders of magnitudes and reduces or eliminates the photonic crystal's distributed in-planemore » feedback. Thus, the photonic crystal can act as a resonator that supports single-mode output from the PCSEL over a larger area than is possible with conventional PCSELs, which have quadratic band edge dispersion. Because output power generally scales with output area, this increase in output area results in higher possible output powers.« less

Birefringence and hidden photons

NASA Astrophysics Data System (ADS)

Arza, Ariel; Gamboa, J.

2018-05-01

We study a model where photons interact with hidden photons and millicharged particles through a kinetic mixing term. Particularly, we focus on vacuum birefringence effects and we find a bound for the millicharged parameter assuming that hidden photons are a piece of the local dark matter density.

Pulmonary functions in plastic factory workers: a preliminary study.

PubMed

Khaliq, Farah; Singh, Pawan; Chandra, Prakash; Gupta, Keshav; Vaney, Neelam

2011-01-01

Exposure to long term air pollution in the work environment may result in decreased lung functions and various other health problems. A significant occupational hazard to lung functions is experienced by plastic factory workers. The present study is planned to assess the pulmonary functions of workers in the plastic factory where recycling of pastic material was done. These workers were constantly exposed to fumes of various chemicals throughout the day. Thirty one workers of plastic factory were assessed for their pulmonary functions. Parameters were compared with 31 age and sex matched controls not exposed to the same environment. The pulmonary function tests were done using Sibelmed Datospir 120 B portable spirometer. A significant decrease in most of the flow rates (MEF 25%, MEF 50%, MEF 75% and FEF 25-75%) and most of the lung volumes and capacities (FVC, FEV1, VC, TV, ERV, MVV) were observed in the workers. Smoking and duration of exposure were not affecting the lung functions as the non smokers also showed a similar decrement in pulmonary functions. Similarly the workers working for less than 5 years also had decrement in pulmonary functions indicating that their lungs are being affected even if they have worked for one year. Exposure to the organic dust in the work environment should be controlled by adequate engineering measures, complemented by effective personal respiratory protection.

Determinants of Chronic Respiratory Symptoms among Pharmaceutical Factory Workers

PubMed Central

Enquselassie, Fikre; Tefera, Yifokire; Gizaw, Muluken; Wakuma, Samson; Woldemariam, Messay

2018-01-01

Background Chronic respiratory symptoms including chronic cough, chronic phlegm, wheezing, shortness of breath, and chest pain are manifestations of respiratory problems which are mainly evolved as a result of occupational exposures. This study aims to assess determinants of chronic respiratory symptoms among pharmaceutical factory workers. Methods A case control study was carried out among 453 pharmaceutical factory workers with 151 cases and 302 controls. Data was collected using pretested and structured questionnaire. The data was analyzed using descriptive statistics and bivariate and multivariate analysis. Result Previous history of chronic respiratory diseases (AOR = 3.36, 95% CI = 1.85–6.12), family history of chronic respiratory diseases (AOR = 2.55, 95% CI = 1.51–4.32), previous dusty working environment (AOR = 2.26, 95% CI = 1.07–4.78), ever smoking (AOR = 3.66, 95% CI = 1.05–12.72), and service years (AOR = 1.86, 95% CI = 1.16–2.99) showed statistically significant association with chronic respiratory symptoms. Conclusion Previous history of respiratory diseases, family history of chronic respiratory diseases, previous dusty working environment, smoking, and service years were determinants of chronic respiratory symptoms. Public health endeavors to prevent the burden of chronic respiratory symptoms among pharmaceutical factory workers should target the reduction of adverse workplace exposures and discouragement of smoking. PMID:29666655

All-photonic quantum repeaters

PubMed Central

Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

2015-01-01

Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories. PMID:25873153

Photonic crystals, amorphous materials, and quasicrystals.

PubMed

Edagawa, Keiichi

2014-06-01

Photonic crystals consist of artificial periodic structures of dielectrics, which have attracted much attention because of their wide range of potential applications in the field of optics. We may also fabricate artificial amorphous or quasicrystalline structures of dielectrics, i.e. photonic amorphous materials or photonic quasicrystals. So far, both theoretical and experimental studies have been conducted to reveal the characteristic features of their optical properties, as compared with those of conventional photonic crystals. In this article, we review these studies and discuss various aspects of photonic amorphous materials and photonic quasicrystals, including photonic band gap formation, light propagation properties, and characteristic photonic states.

Two-dimensional topological photonics

NASA Astrophysics Data System (ADS)

Khanikaev, Alexander B.; Shvets, Gennady

2017-12-01

Originating from the studies of two-dimensional condensed-matter states, the concept of topological order has recently been expanded to other fields of physics and engineering, particularly optics and photonics. Topological photonic structures have already overturned some of the traditional views on wave propagation and manipulation. The application of topological concepts to guided wave propagation has enabled novel photonic devices, such as reflection-free sharply bent waveguides, robust delay lines, spin-polarized switches and non-reciprocal devices. Discrete degrees of freedom, widely used in condensed-matter physics, such as spin and valley, are now entering the realm of photonics. In this Review, we summarize the latest advances in this highly dynamic field, with special emphasis on the experimental work on two-dimensional photonic topological structures.

The 9-item Bergen Burnout Inventory: factorial validity across organizations and measurements of longitudinal data.

PubMed

Feldt, Taru; Rantanen, Johanna; Hyvönen, Katriina; Mäkikangas, Anne; Huhtala, Mari; Pihlajasaari, Pia; Kinnunen, Ulla

2014-01-01

The present study tested the factorial validity of the 9-item Bergen Burnout Inventory (BBI-9). The BBI-9 is comprised of three core dimensions: (1) exhaustion at work; (2) cynicism toward the meaning of work; and (3) sense of inadequacy at work. The study further investigated whether the three-factor structure of the BBI-9 remains the same across different organizations (group invariance) and measurement time points (time invariance). The factorial group invariance was tested using a cross-sectional design with data pertaining to managers (n=742), and employees working in a bank (n=162), an engineering office (n=236), a public sector organization divided into three service areas: administration (n=102), education and culture (n=581), and social affairs and health (n=1,505). Factorial time invariance was tested using longitudinal data pertaining to managers, with three measurements over a four-year follow-up period. The confirmatory factor analysis revealed that the three-factor structure of the BBI-9 was invariant across cross-sectional samples. The factorial invariance was also supported across measurement times. To conclude, the factorial structure of the BBI-9 was found to remain the same regardless of the sample properties and measurement times.

Photon Physics and Plasma Research, Photonics Applications and Web Engineering, Wilga, May 2012

NASA Astrophysics Data System (ADS)

Romaniuk, Ryszard S.

2012-05-01

This paper is the third part (out of five) of the research survey of WILGA Symposium work, May 2012 Edition, concerned with Photon Physics and Plasma Research. It presents a digest of chosen technical work results shown by young researchers from different technical universities from this country during the Jubilee XXXth SPIE-IEEE Wilga 2012, May Edition, symposium on Photonics and Web Engineering. Topical tracks of the symposium embraced, among others, nanomaterials and nanotechnologies for photonics, sensory and nonlinear optical fibers, object oriented design of hardware, photonic metrology, optoelectronics and photonics applications, photonics-electronics co-design, optoelectronic and electronic systems for astronomy and high energy physics experiments, JET tokamak and pi-of-the sky experiments development. The symposium is an annual summary in the development of numerable Ph.D. theses carried out in this country in the area of advanced electronic and photonic systems. It is also a great occasion for SPIE, IEEE, OSA and PSP students to meet together in a large group spanning the whole country with guests from this part of Europe. A digest of Wilga references is presented [1-270].

Photonic crystals, amorphous materials, and quasicrystals

PubMed Central

Edagawa, Keiichi

2014-01-01

Photonic crystals consist of artificial periodic structures of dielectrics, which have attracted much attention because of their wide range of potential applications in the field of optics. We may also fabricate artificial amorphous or quasicrystalline structures of dielectrics, i.e. photonic amorphous materials or photonic quasicrystals. So far, both theoretical and experimental studies have been conducted to reveal the characteristic features of their optical properties, as compared with those of conventional photonic crystals. In this article, we review these studies and discuss various aspects of photonic amorphous materials and photonic quasicrystals, including photonic band gap formation, light propagation properties, and characteristic photonic states. PMID:27877676

Review on Dark Photon

NASA Astrophysics Data System (ADS)

Curciarello, Francesca

2016-04-01

e+e- collider experiments at the intensity frontier are naturally suited to probe the existence of a force beyond the Standard Model between WIMPs, the most viable dark matter candidates. The mediator of this new force, known as dark photon, should be a new vector gauge boson very weakly coupled to the Standard Model photon. No significant signal has been observed so far. I will report on current limits set on the coupling factor ɛ2 between the photon and the dark photon by e+e- collider experiments.

Progress in neuromorphic photonics

NASA Astrophysics Data System (ADS)

Ferreira de Lima, Thomas; Shastri, Bhavin J.; Tait, Alexander N.; Nahmias, Mitchell A.; Prucnal, Paul R.

2017-03-01

As society's appetite for information continues to grow, so does our need to process this information with increasing speed and versatility. Many believe that the one-size-fits-all solution of digital electronics is becoming a limiting factor in certain areas such as data links, cognitive radio, and ultrafast control. Analog photonic devices have found relatively simple signal processing niches where electronics can no longer provide sufficient speed and reconfigurability. Recently, the landscape for commercially manufacturable photonic chips has been changing rapidly and now promises to achieve economies of scale previously enjoyed solely by microelectronics. By bridging the mathematical prowess of artificial neural networks to the underlying physics of optoelectronic devices, neuromorphic photonics could breach new domains of information processing demanding significant complexity, low cost, and unmatched speed. In this article, we review the progress in neuromorphic photonics, focusing on photonic integrated devices. The challenges and design rules for optoelectronic instantiation of artificial neurons are presented. The proposed photonic architecture revolves around the processing network node composed of two parts: a nonlinear element and a network interface. We then survey excitable lasers in the recent literature as candidates for the nonlinear node and microring-resonator weight banks as the network interface. Finally, we compare metrics between neuromorphic electronics and neuromorphic photonics and discuss potential applications.

Brutal and negligent? 19th century factory mothers and child care.

PubMed

Reynolds, Melanie

2011-10-01

This paper aims to highlight some working class women's childcare practices in northern industrial areas of Britain during the latter half of the 19th century. It aims to challenge the commonly held belief that 19th century northern working-class factory mothers were irresponsive and neglectful toward their infants, thereby fuelling the high northern infant mortality rate. It will do this by showing that factory mothers were responsible and responsive toward their infants despite being thwarted by the working patterns of industrialisation. It begins by outlining the arguments made by historians that northern working class women were neglectful toward their children. Then key areas such as the working patterns of waged factory mothers will be illustrated to show the agency and determination of 19th century working class women to provide their infants with good care. Reassessment of these historical childcare practices can provide a springboard by which today's health professionals can endeavour to maintain accurate and fair perspectives about the childcare practices of today's women of low socio-economic status.

MapFactory - Towards a mapping design pattern for big geospatial data

NASA Astrophysics Data System (ADS)

Rautenbach, Victoria; Coetzee, Serena

2018-05-01

With big geospatial data emerging, cartographers and geographic information scientists have to find new ways of dealing with the volume, variety, velocity, and veracity (4Vs) of the data. This requires the development of tools that allow processing, filtering, analysing, and visualising of big data through multidisciplinary collaboration. In this paper, we present the MapFactory design pattern that will be used for the creation of different maps according to the (input) design specification for big geospatial data. The design specification is based on elements from ISO19115-1:2014 Geographic information - Metadata - Part 1: Fundamentals that would guide the design and development of the map or set of maps to be produced. The results of the exploratory research suggest that the MapFactory design pattern will help with software reuse and communication. The MapFactory design pattern will aid software developers to build the tools that are required to automate map making with big geospatial data. The resulting maps would assist cartographers and others to make sense of big geospatial data.

Factorial correspondence analysis of fear-related behaviour traits in Japanese quail.

PubMed

Mignon-Grasteau, S; Roussot, O; Delaby, C; Faure, J M.; Mills, A; Leterrier, C; Guéméné, D; Constantin, P; Mills, M; Lepape, G; Beaumont, C

2003-02-28

Factorial correspondence analysis was performed on 341 quails from a F2 cross between two lines divergently selected on the duration of tonic immobility over 29 generations. Several fear- or stress-related traits were recorded, i.e. tonic immobility duration, number of inductions needed to induce tonic immobility, open-field behaviour (time spent walking, latency before first movement and number of defecations), asymmetry of tibia lengths and corticosterone concentration after restraint stress. Variables were categorised in classes and analysed by factorial correspondence analysis. The first axis was mostly described by open-field behaviour, and the second by tonic immobility traits (duration of tonic immobility and number of inductions), which showed that these behaviours were almost independent. No relationship was found between axes of the factorial correspondence analysis and corticosterone concentration or asymmetry of tibia lengths, showing that these variables reflected other characteristics of stress susceptibility than those described by tonic immobility and open-field behaviour. These results show that reaction to stress of quails is a multidimensional trait and cannot be summarised by one trait.

Roadmap on silicon photonics

NASA Astrophysics Data System (ADS)

Thomson, David; Zilkie, Aaron; Bowers, John E.; Komljenovic, Tin; Reed, Graham T.; Vivien, Laurent; Marris-Morini, Delphine; Cassan, Eric; Virot, Léopold; Fédéli, Jean-Marc; Hartmann, Jean-Michel; Schmid, Jens H.; Xu, Dan-Xia; Boeuf, Frédéric; O'Brien, Peter; Mashanovich, Goran Z.; Nedeljkovic, M.

2016-07-01

Silicon photonics research can be dated back to the 1980s. However, the previous decade has witnessed an explosive growth in the field. Silicon photonics is a disruptive technology that is poised to revolutionize a number of application areas, for example, data centers, high-performance computing and sensing. The key driving force behind silicon photonics is the ability to use CMOS-like fabrication resulting in high-volume production at low cost. This is a key enabling factor for bringing photonics to a range of technology areas where the costs of implementation using traditional photonic elements such as those used for the telecommunications industry would be prohibitive. Silicon does however have a number of shortcomings as a photonic material. In its basic form it is not an ideal material in which to produce light sources, optical modulators or photodetectors for example. A wealth of research effort from both academia and industry in recent years has fueled the demonstration of multiple solutions to these and other problems, and as time progresses new approaches are increasingly being conceived. It is clear that silicon photonics has a bright future. However, with a growing number of approaches available, what will the silicon photonic integrated circuit of the future look like? This roadmap on silicon photonics delves into the different technology and application areas of the field giving an insight into the state-of-the-art as well as current and future challenges faced by researchers worldwide. Contributions authored by experts from both industry and academia provide an overview and outlook for the silicon waveguide platform, optical sources, optical modulators, photodetectors, integration approaches, packaging, applications of silicon photonics and approaches required to satisfy applications at mid-infrared wavelengths. Advances in science and technology required to meet challenges faced by the field in each of these areas are also addressed together with

A community-initiated study of blood lead levels of Nicaraguan children living near a battery factory.

PubMed Central

Morales Bonilla, C; Mauss, E A

1998-01-01

OBJECTIVES: In response to requests by parents in Managua, Nicaragua, whose neighborhood borders a battery factory, 97 children were tested for blood lead, as were 30 children in a neighborhood without an obvious source of environmental lead. METHODS: Venous blood was examined by atomic absorption spectrophotometry. Educational workshops were conducted. RESULTS: Mean blood lead levels were 17.21 +/- 9.92 micrograms/dL in the index children and 7.40 +/- 5.37 micrograms/dL in the controls (P < .001). CONCLUSIONS: Children living near the battery factory are at increased risk of lead poisoning. The parents were able to petition the government to control the factory emissions and to improve appropriate health services. The factory is now closed. PMID:9842385

Factorial versus multi-arm multi-stage designs for clinical trials with multiple treatments.

PubMed

Jaki, Thomas; Vasileiou, Despina

2017-02-20

When several treatments are available for evaluation in a clinical trial, different design options are available. We compare multi-arm multi-stage with factorial designs, and in particular, we will consider a 2 × 2 factorial design, where groups of patients will either take treatments A, B, both or neither. We investigate the performance and characteristics of both types of designs under different scenarios and compare them using both theory and simulations. For the factorial designs, we construct appropriate test statistics to test the hypothesis of no treatment effect against the control group with overall control of the type I error. We study the effect of the choice of the allocation ratios on the critical value and sample size requirements for a target power. We also study how the possibility of an interaction between the two treatments A and B affects type I and type II errors when testing for significance of each of the treatment effects. We present both simulation results and a case study on an osteoarthritis clinical trial. We discover that in an optimal factorial design in terms of minimising the associated critical value, the corresponding allocation ratios differ substantially to those of a balanced design. We also find evidence of potentially big losses in power in factorial designs for moderate deviations from the study design assumptions and little gain compared with multi-arm multi-stage designs when the assumptions hold. © 2016 The Authors. Statistics in Medicine Published by John Wiley & Sons Ltd. © 2016 The Authors. Statistics in Medicine Published by John Wiley & Sons Ltd.

Carbonate factories: A conundrum in sedimentary geology

NASA Astrophysics Data System (ADS)

Pomar, L.; Hallock, P.

2008-03-01

by the end-Permian extinctions, excess photosynthesis by phytoplankton and microbial assemblages in surface waters, induced by moderately high CO 2 and temperature during the Early Mesozoic, supported proliferation of non-tissular metazoans (e.g., sponges) and heterotrophic bacteria at the sea floor. Metabolic activity by those microbes, especially sulfate reduction, resulted in abundant biologically-induced geochemical carbonate precipitation on and within the sea floor. For example, with the opening of Tethyan seaways during the Triassic, massive sponge/microbe boundstones (the benthic automicrite factory) formed steep, massive and thick progradational slopes and, locally, mud-mounds. As tectonic processes created shallow epicontinental seas, photosynthesis drove lime-mud precipitation in the illuminated zone of the water column. The resulting neritic lime-mud component of the shallow-water carbonate factory became predominant during the Jurassic, paralleling the increase in atmospheric pCO 2, while the decreasing importance of the benthic automicrite factory parallels the diversification of calcifying metazoans, phytoplankton and zooplankton. With atmospheric pCO 2 declining through the Cretaceous, the potential habitats for neritic lime-mud precipitation declined. At the same time, peak oceanic Ca 2+ concentrations promoted biotically-controlled calcification by the skeletal factory. With changes produced by extinctions and turnovers at the Cretaceous-Tertiary boundary, adaptations to decreasing Ca 2+ and pCO 2, coupled with increasing global temperature gradients (i.e., high-latitude and deep-water cooling), and strategies that efficiently linked photosynthesis and calcification, promoted successive changes of the dominant skeletal factory through the Cenozoic: larger benthic foraminifers (protist-protist symbiosis) during the Paleogene, red algae during the Miocene and modern coral reefs (metazoan-protist symbiosis) since Late Miocene.

Merging photonics with nanoelectronics (Conference Presentation)

NASA Astrophysics Data System (ADS)

Liehr, Michael

2016-02-01

The recently established American Institute for Manufacturing Photonics (AIM Photonics) is a manufacturing consortium headquartered in New York, with funding from the US Department of Defense (DoD), New York State, and industrial partners to advance the state of the art in the design, manufacture, testing, assembly, and packaging of integrated photonic devices. Dr. Michael Liehr, CEO of AIM Photonics, will describe the technical goals, operational framework, near-term milestones, and opportunities for the broader photonics community. The Institute intends to organize a currently fragmented domestic capability in integrated photonics. AIM Photonics will develop and demonstrate innovative manufacturing technologies for a number of key application sectors for integrated photonics devices. The Institute will furthermore specifically focus on establishing and building out an infrastructure in key areas required to accelerate the further adoption of integrated photonics. Specifically, we will enhance the available hardware development capability to include Si-based Multi-Project Wafer runs, InP-based Photonic Integrated Circuits, first and second level packaging, test and assembly.

Analysis of photonic band gap in novel piezoelectric photonic crystal

NASA Astrophysics Data System (ADS)

Malar Kodi, A.; Doni Pon, V.; Joseph Wilson, K. S.

2018-03-01

The transmission properties of one-dimensional novel photonic crystal having silver-doped novel piezoelectric superlattice and air as the two constituent layers have been investigated by means of transfer matrix method. By changing the appropriate thickness of the layers and filling factor of nanocomposite system, the variation in the photonic band gap can be studied. It is found that the photonic band gap increases with the filling factor of the metal nanocomposite and with the thickness of the layer. These structures possess unique characteristics enabling one to operate as optical waveguides, selective filters, optical switches, integrated piezoelectric microactuators, etc.

Emerging technologies in Si active photonics

NASA Astrophysics Data System (ADS)

Wang, Xiaoxin; Liu, Jifeng

2018-06-01

Silicon photonics for synergistic electronic–photonic integration has achieved remarkable progress in the past two decades. Active photonic devices, including lasers, modulators, and photodetectors, are the key challenges for Si photonics to meet the requirement of high bandwidth and low power consumption in photonic datalinks. Here we review recent efforts and progress in high-performance active photonic devices on Si, focusing on emerging technologies beyond conventional foundry-ready Si photonics devices. For emerging laser sources, we will discuss recent progress towards efficient monolithic Ge lasers, mid-infrared GeSn lasers, and high-performance InAs quantum dot lasers on Si for data center applications in the near future. We will then review novel modulator materials and devices beyond the free carrier plasma dispersion effect in Si, including GeSi and graphene electro-absorption modulators and plasmonic-organic electro-optical modulators, to achieve ultralow power and high speed modulation. Finally, we discuss emerging photodetectors beyond epitaxial Ge p–i–n photodiodes, including GeSn mid-infrared photodetectors, all-Si plasmonic Schottky infrared photodetectors, and Si quanta image sensors for non-avalanche, low noise single photon detection and photon counting. These emerging technologies, though still under development, could make a significant impact on the future of large-scale electronicSilicon photonics for synergistic electronic-photonic integration has achieved remarkable progress in the past two decades. Active photonic devices, including lasers, modulators, and photodetectors, are the key challenges for Si photonics to meet the requirement of high bandwidth and low power consumption in photonic datalinks. Here we review recent efforts and progress in high-performance active photonic devices on Si, focusing on emerging technologies beyond conventional foundry-ready Si photonics devices. For emerging laser sources, we will discuss recent

Gender bias in nineteenth-century England: Evidence from factory children.

PubMed

Horrell, Sara; Oxley, Deborah

2016-09-01

Gender bias against girls in nineteenth-century England has received much interest but establishing its existence has proved difficult. We utilise data on heights of 16,402 children working in northern textile factories in 1837 to examine whether gender bias was evident. Current interpretations argue against any difference. Here our comparisons with modern height standards reveal greater deprivation for girls than for boys. Discrimination is measured in girls' height-for-age score (HAZ) falling eight standard errors below boys' at ages 11, 11.5 and 12 years of age, capturing the very poor performance of factory girls. But this result cannot be taken at face value. We query whether modern standards require adjustment to account for the later timing of puberty in historical populations and develop an alternative. We also test the validity of the age data, considering whether parents were more prone to lie about the ages of their daughters, and question whether the supply of girls was fundamentally different from that of boys. We conclude that neither proposition is justified. Disadvantage to girls remains, although its absence amongst younger children precludes an indictment of culturally founded gender bias. The height data must remain mute on the source of this discrimination but we utilise additional information to examine some hypotheses: occupational sorting, differential susceptibility to disease, poorer nutrition for girls, disproportionate stunting from the effects of nutritional deprivation, and type and amount of work undertaken. Of these we suggest that girls had to do arduous physical labour in the home alongside their factory work. The only (unsubstantiated) alternative is that girls were more likely than boys to be put into factory work below the legal age limit. Both represent forms of gender bias. Copyright © 2016 Elsevier B.V. All rights reserved.

Ion photon emission microscope

DOEpatents

Doyle, Barney L.

2003-04-22

An ion beam analysis system that creates microscopic multidimensional image maps of the effects of high energy ions from an unfocussed source upon a sample by correlating the exact entry point of an ion into a sample by projection imaging of the ion-induced photons emitted at that point with a signal from a detector that measures the interaction of that ion within the sample. The emitted photons are collected in the lens system of a conventional optical microscope, and projected on the image plane of a high resolution single photon position sensitive detector. Position signals from this photon detector are then correlated in time with electrical effects, including the malfunction of digital circuits, detected within the sample that were caused by the individual ion that created these photons initially.

A semiconductor photon-sorter

NASA Astrophysics Data System (ADS)

Bennett, A. J.; Lee, J. P.; Ellis, D. J. P.; Farrer, I.; Ritchie, D. A.; Shields, A. J.

2016-10-01

Obtaining substantial nonlinear effects at the single-photon level is a considerable challenge that holds great potential for quantum optical measurements and information processing. Of the progress that has been made in recent years one of the most promising methods is to scatter coherent light from quantum emitters, imprinting quantum correlations onto the photons. We report effective interactions between photons, controlled by a single semiconductor quantum dot that is weakly coupled to a monolithic cavity. We show that the nonlinearity of a transition modifies the counting statistics of a Poissonian beam, sorting the photons in number. This is used to create strong correlations between detection events and to create polarization-correlated photons from an uncorrelated stream using a single spin. These results pave the way for semiconductor optical switches operated by single quanta of light.

Expression in Escherichia coli, refolding and crystallization of Aspergillus niger feruloyl esterase A using a serial factorial approach.

PubMed

Benoit, Isabelle; Coutard, Bruno; Oubelaid, Rachid; Asther, Marcel; Bignon, Christophe

2007-09-01

Hydrolysis of plant biomass is achieved by the combined action of enzymes secreted by microorganisms and directed against the backbone and the side chains of plant cell wall polysaccharides. Among side chains degrading enzymes, the feruloyl esterase A (FAEA) specifically removes feruloyl residues. Thus, FAEA has potential applications in a wide range of industrial processes such as paper bleaching or bio-ethanol production. To gain insight into FAEA hydrolysis activity, we solved its crystal structure. In this paper, we report how the use of four consecutive factorial approaches (two incomplete factorials, one sparse matrix, and one full factorial) allowed expressing in Escherichia coli, refolding and then crystallizing Aspergillus niger FAEA in 6 weeks. Culture conditions providing the highest expression level were determined using an incomplete factorial approach made of 12 combinations of four E. coli strains, three culture media and three temperatures (full factorial: 36 combinations). Aspergillus niger FAEA was expressed in the form of inclusion bodies. These were dissolved using a chaotropic agent, and the protein was purified by affinity chromatography on Ni column under denaturing conditions. A suitable buffer for refolding the protein eluted from the Ni column was found using a second incomplete factorial approach made of 96 buffers (full factorial: 3840 combinations). After refolding, the enzyme was further purified by gel filtration, and then crystallized following a standard protocol: initial crystallization conditions were found using commercial crystallization screens based on a sparse matrix. Crystals were then optimized using a full factorial screen.

Factory approach can streamline patient accounting.

PubMed

Rands, J; Muench, M

1991-08-01

Although they may seem fundamentally different, similarities exist between operations of factories and healthcare organizations' business offices. As a result, a patient accounting approach based on manufacturing firms' management techniques may help smooth healthcare business processes. Receivables performance management incorporates the Japanese techniques of "just-in-time" and total quality management to reduce unbilled accounts and information backlog and accelerate payment. A preliminary diagnostic assessment of a patient accounting process helps identify bottlenecks and set priorities for work flow.

Optomechanical measurement of photon spin angular momentum and optical torque in integrated photonic devices.

PubMed

He, Li; Li, Huan; Li, Mo

2016-09-01

Photons carry linear momentum and spin angular momentum when circularly or elliptically polarized. During light-matter interaction, transfer of linear momentum leads to optical forces, whereas transfer of angular momentum induces optical torque. Optical forces including radiation pressure and gradient forces have long been used in optical tweezers and laser cooling. In nanophotonic devices, optical forces can be significantly enhanced, leading to unprecedented optomechanical effects in both classical and quantum regimes. In contrast, to date, the angular momentum of light and the optical torque effect have only been used in optical tweezers but remain unexplored in integrated photonics. We demonstrate the measurement of the spin angular momentum of photons propagating in a birefringent waveguide and the use of optical torque to actuate rotational motion of an optomechanical device. We show that the sign and magnitude of the optical torque are determined by the photon polarization states that are synthesized on the chip. Our study reveals the mechanical effect of photon's polarization degree of freedom and demonstrates its control in integrated photonic devices. Exploiting optical torque and optomechanical interaction with photon angular momentum can lead to torsional cavity optomechanics and optomechanical photon spin-orbit coupling, as well as applications such as optomechanical gyroscopes and torsional magnetometry.

Recent progress in neutrino factory and muon collider research within the Muon Collaboration

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. M. Alsharoa; Charles M. Ankenbrandt; Muzaffer Atac

2003-08-01

We describe the status of our effort to realize a first neutrino factory and the progress made in understanding the problems associated with the collection and cooling of muons towards that end. We summarize the physics that can be done with neutrino factories as well as with intense cold beams of muons. The physics potential of muon colliders is reviewed, both as Higgs Factories and compact high energy lepton colliders. The status and timescale of our research and development effort is reviewed as well as the latest designs in cooling channels including the promise of ring coolers in achieving longitudinalmore » and transverse cooling simultaneously. We detail the efforts being made to mount an international cooling experiment to demonstrate the ionization cooling of muons.« less

Background-Source Cosmic-Photon Elevation Scaling and Cosmic-Neutron/Photon Date Scaling in MCNP6

DOE PAGES

Tutt, James Robert; Anderson, Casey Alan; McKinney, Gregg Walter

2017-10-26

Here, cosmic neutron and photon fluxes are known to scale exponentially with elevation. Consequently, cosmic neutron elevation scaling was implemented for use with the background-source option shortly after its introduction into MCNP6, whereby the neutron flux weight factor was adjusted by the elevation scaling factor when the user-specified elevation differed from the selected background.dat grid-point elevation. At the same time, an elevation scaling factor was suggested for the cosmic photon flux, however, cosmic photon elevation scaling is complicated by the fact that the photon background consists of two components: cosmic and terrestrial. Previous versions of the background.dat file did notmore » provide any way to separate these components. With Rel. 4 of this file in 2015, two new columns were added that provide the energy grid and differential cosmic photon flux separately from the total photon flux. Here we show that the cosmic photon flux component can now be scaled independently and combined with the terrestrial component to form the total photon flux at a user-specified elevation in MCNP6.« less

Background-Source Cosmic-Photon Elevation Scaling and Cosmic-Neutron/Photon Date Scaling in MCNP6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tutt, James Robert; Anderson, Casey Alan; McKinney, Gregg Walter

Here, cosmic neutron and photon fluxes are known to scale exponentially with elevation. Consequently, cosmic neutron elevation scaling was implemented for use with the background-source option shortly after its introduction into MCNP6, whereby the neutron flux weight factor was adjusted by the elevation scaling factor when the user-specified elevation differed from the selected background.dat grid-point elevation. At the same time, an elevation scaling factor was suggested for the cosmic photon flux, however, cosmic photon elevation scaling is complicated by the fact that the photon background consists of two components: cosmic and terrestrial. Previous versions of the background.dat file did notmore » provide any way to separate these components. With Rel. 4 of this file in 2015, two new columns were added that provide the energy grid and differential cosmic photon flux separately from the total photon flux. Here we show that the cosmic photon flux component can now be scaled independently and combined with the terrestrial component to form the total photon flux at a user-specified elevation in MCNP6.« less

A photonic transistor device based on photons and phonons in a cavity electromechanical system

NASA Astrophysics Data System (ADS)

Jiang, Cheng; Zhu, Ka-Di

2013-01-01

We present a scheme for photonic transistors based on photons and phonons in a cavity electromechanical system, which is composed of a superconducting microwave cavity coupled to a nanomechanical resonator. Control of the propagation of photons is achieved through the interaction of microwave field (photons) and nanomechanical vibrations (phonons). By calculating the transmission spectrum of the signal field, we show that the signal field can be efficiently attenuated or amplified, depending on the power of a second ‘gating’ (pump) field. This scheme may be a promising candidate for single-photon transistors and pave the way for numerous applications in telecommunication and quantum information technologies.

Black holes as antimatter factories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bambi, Cosimo; Petrov, Alexey A.; Dolgov, Alexander D., E-mail: cosimo.bambi@ipmu.jp, E-mail: dolgov@fe.infn.it, E-mail: apetrov@physics.wayne.edu

2009-09-01

We consider accretion of matter onto a low mass black hole surrounded by ionized medium. We show that, because of the higher mobility of protons than electrons, the black hole would acquire positive electric charge. If the black hole's mass is about or below 10{sup 20} g, the electric field at the horizon can reach the critical value which leads to vacuum instability and electron-positron pair production by the Schwinger mechanism. Since the positrons are ejected by the emergent electric field, while electrons are back-captured, the black hole operates as an antimatter factory which effectively converts protons into positrons.

Information security of Smart Factories

NASA Astrophysics Data System (ADS)

Iureva, R. A.; Andreev, Y. S.; Iuvshin, A. M.; Timko, A. S.

2018-05-01

In several years, technologies and systems based on the Internet of things (IoT) will be widely used in all smart factories. When processing a huge array of unstructured data, their filtration and adequate interpretation are a priority for enterprises. In this context, the correct representation of information in a user-friendly form acquires special importance, for which the market today presents advanced analytical platforms designed to collect, store and analyze data on technological processes and events in real time. The main idea of the paper is the statement of the information security problem in IoT and integrity of processed information.

Nonlinear silicon photonics

NASA Astrophysics Data System (ADS)

Tsia, Kevin K.; Jalali, Bahram

2010-05-01

An intriguing optical property of silicon is that it exhibits a large third-order optical nonlinearity, with orders-ofmagnitude larger than that of silica glass in the telecommunication band. This allows efficient nonlinear optical interaction at relatively low power levels in a small footprint. Indeed, we have witnessed a stunning progress in harnessing the Raman and Kerr effects in silicon as the mechanisms for enabling chip-scale optical amplification, lasing, and wavelength conversion - functions that until recently were perceived to be beyond the reach of silicon. With all the continuous efforts developing novel techniques, nonlinear silicon photonics is expected to be able to reach even beyond the prior achievements. Instead of providing a comprehensive overview of this field, this manuscript highlights a number of new branches of nonlinear silicon photonics, which have not been fully recognized in the past. In particular, they are two-photon photovoltaic effect, mid-wave infrared (MWIR) silicon photonics, broadband Raman effects, inverse Raman scattering, and periodically-poled silicon (PePSi). These novel effects and techniques could create a new paradigm for silicon photonics and extend its utility beyond the traditionally anticipated applications.

Ultrafast single photon emitting quantum photonic structures based on a nano-obelisk.

PubMed

Kim, Je-Hyung; Ko, Young-Ho; Gong, Su-Hyun; Ko, Suk-Min; Cho, Yong-Hoon

2013-01-01

A key issue in a single photon source is fast and efficient generation of a single photon flux with high light extraction efficiency. Significant progress toward high-efficiency single photon sources has been demonstrated by semiconductor quantum dots, especially using narrow bandgap materials. Meanwhile, there are many obstacles, which restrict the use of wide bandgap semiconductor quantum dots as practical single photon sources in ultraviolet-visible region, despite offering free space communication and miniaturized quantum information circuits. Here we demonstrate a single InGaN quantum dot embedded in an obelisk-shaped GaN nanostructure. The nano-obelisk plays an important role in eliminating dislocations, increasing light extraction, and minimizing a built-in electric field. Based on the nano-obelisks, we observed nonconventional narrow quantum dot emission and positive biexciton binding energy, which are signatures of negligible built-in field in single InGaN quantum dots. This results in efficient and ultrafast single photon generation in the violet color region.

Behavioral lifestyle and mental health status of Japanese factory workers.

PubMed

Ezoe, S; Morimoto, K

1994-01-01

Lifestyle factors, sometimes associated with physical health and mortality, have also been known to be associated with mental health status. This study seeks to correlate behavioral lifestyles with major components of mental health among Japanese factory workers. We administered the 28-item version of the General Health Questionnaire (GHQ-28) and a questionnaire concerning eight personal health practices to 2,132 male and 668 female factory workers at a camera-manufacturing company in Japan. There were strong negative relationships of a higher total number of favorable lifestyles as indicated by the Health Practice Index (HPI) to psychological distress and its components: somatic symptoms, anxiety-insomnia, and social dysfunction. After controlling for the effects of confounding factors that included age, marital status, and somatic condition, multiple logistic regression analysis indicated that five of the eight health factors among male workers--mental stress, nutritional balance, eating breakfast regularly, physical exercise, and working hours--were significantly related to the grade of psychological distress or its three components. Among female workers, five health practices, i.e., mental stress, physical exercise, sleeping hours, working hours, and cigarette smoking, were significantly associated with the grade of psychological distress or its three components. Good health practices might be individually and as a whole associated with better mental health status in factory workers.

Algal Cell Factories: Approaches, Applications, and Potentials.

PubMed

Fu, Weiqi; Chaiboonchoe, Amphun; Khraiwesh, Basel; Nelson, David R; Al-Khairy, Dina; Mystikou, Alexandra; Alzahmi, Amnah; Salehi-Ashtiani, Kourosh

2016-12-13

With the advent of modern biotechnology, microorganisms from diverse lineages have been used to produce bio-based feedstocks and bioactive compounds. Many of these compounds are currently commodities of interest, in a variety of markets and their utility warrants investigation into improving their production through strain development. In this review, we address the issue of strain improvement in a group of organisms with strong potential to be productive "cell factories": the photosynthetic microalgae. Microalgae are a diverse group of phytoplankton, involving polyphyletic lineage such as green algae and diatoms that are commonly used in the industry. The photosynthetic microalgae have been under intense investigation recently for their ability to produce commercial compounds using only light, CO₂, and basic nutrients. However, their strain improvement is still a relatively recent area of work that is under development. Importantly, it is only through appropriate engineering methods that we may see the full biotechnological potential of microalgae come to fruition. Thus, in this review, we address past and present endeavors towards the aim of creating productive algal cell factories and describe possible advantageous future directions for the field.

A Hospital Is Not Just a Factory, but a Complex Adaptive System-Implications for Perioperative Care.

PubMed

Mahajan, Aman; Islam, Salim D; Schwartz, Michael J; Cannesson, Maxime

2017-07-01

Many methods used to improve hospital and perioperative services productivity and quality of care have assumed that the hospital is essentially a factory, and therefore, that industrial engineering and manufacturing-derived redesign approaches such as Six Sigma and Lean can be applied to hospitals and perioperative services just as they have been applied in factories. However, a hospital is not merely a factory but also a complex adaptive system (CAS). The hospital CAS has many subsystems, with perioperative care being an important one for which concepts of factory redesign are frequently advocated. In this article, we argue that applying only factory approaches such as lean methodologies or process standardization to complex systems such as perioperative care could account for difficulties and/or failures in improving performance in care delivery. Within perioperative services, only noncomplex/low-variance surgical episodes are amenable to manufacturing-based redesign. On the other hand, complex surgery/high-variance cases and preoperative segmentation (the process of distinguishing between normal and complex cases) can be viewed as CAS-like. These systems tend to self-organize, often resist or react unpredictably to attempts at control, and therefore require application of CAS principles to modify system behavior. We describe 2 examples of perioperative redesign to illustrate the concepts outlined above. These examples present complementary and contrasting cases from 2 leading delivery systems. The Mayo Clinic example illustrates the application of manufacturing-based redesign principles to a factory-like (high-volume, low-risk, and mature practice) clinical program, while the Kaiser Permanente example illustrates the application of both manufacturing-based and self-organization-based approaches to programs and processes that are not factory-like but CAS-like. In this article, we describe how factory-like processes and CAS can coexist within a hospital and how

[Risk assessment and countermeasure of BTEX in pesticide factory].

PubMed

Pang, Bo; Wang, Tie-Yu; Du, Li-Yu; Tan, Bing; Zhu, Zhao-Yun; Lu, Yong-Long

2013-07-01

BTEX are important environmental pollutants, harmful to human through respiratory inhalation, digestive tract and skin contact, and also have teratogenic, mutagenic and carcinogenic effects. BTEX were detected in multi-media to identify their distributions and assess their human health risk in a pesticide factory in Hebei province. Purge and trap GC-MS, adsorption/thermal desorption GC chromatography and the health risk assessment model were applied, and corresponding management measures were proposed. The results showed that BTEX existed in soil, dust, air, groundwater and wastewater. The concentration of BTEX in dust of the production area was 7.33 mg x kg(-1), in particular the concentration of toluene was 5.64 mg x kg(-1), exceeding the Canadian industrial land standard. Building three scenarios for working more than 10 years, 20 years and 30 years, the total non-carcinogens index was 4.19 x10(-3), 8.25 x 10(-3) and 1.22 x 10(-2), respectively, all lower than 1; the carcinogens index of benzene was 1.70 x 10(-7), 3.34 x 10(-7) and 4.92 x 10(-7), respectively, all lower than 10(-6). It indicated that there was no significant non-carcinogens and carcinogens hazard to workers inside the factory, but they might be exposed to more health risks if their work experience increase. Finally, recommendations for improving the environmental quality and personnel security in the factory were proposed based on the research results.

The 9-item Bergen Burnout Inventory: Factorial Validity Across Organizations and Measurements of Longitudinal Data

PubMed Central

Feldt, Taru; RANTANEN, Johanna; HYVÖNEN, Katriina; MÄKIKANGAS, Anne; HUHTALA, Mari; PIHLAJASAARI, Pia; KINNUNEN, Ulla

2013-01-01

The present study tested the factorial validity of the 9-item Bergen Burnout Inventory (BBI-9)1). The BBI-9 is comprised of three core dimensions: (1) exhaustion at work; (2) cynicism toward the meaning of work; and (3) sense of inadequacy at work. The study further investigated whether the three-factor structure of the BBI-9 remains the same across different organizations (group invariance) and measurement time points (time invariance). The factorial group invariance was tested using a cross-sectional design with data pertaining to managers (n=742), and employees working in a bank (n=162), an engineering office (n=236), a public sector organization divided into three service areas: administration (n=102), education and culture (n=581), and social affairs and health (n=1,505). Factorial time invariance was tested using longitudinal data pertaining to managers, with three measurements over a four-year follow-up period. The confirmatory factor analysis revealed that the three-factor structure of the BBI-9 was invariant across cross-sectional samples. The factorial invariance was also supported across measurement times. To conclude, the factorial structure of the BBI-9 was found to remain the same regardless of the sample properties and measurement times. PMID:24366535

Muon Accelerator Program (MAP) | Neutrino Factory | Research Goals

Science.gov Websites

; Committees Research Goals Research & Development Design & Simulation Technology Development Systems Demonstrations Activities MASS Muon Cooling MuCool Test Area MICE Experiment MERIT Muon Collider Research Goals Why Muons at the Energy Frontier? How does it work? Graphics Animation Neutrino Factory Research Goals

Photonic quantum information: science and technology

PubMed Central

TAKEUCHI, Shigeki

2016-01-01

Recent technological progress in the generation, manipulation and detection of individual single photons has opened a new scientific field of photonic quantum information. This progress includes the realization of single photon switches, photonic quantum circuits with specific functions, and the application of novel photonic states to novel optical metrology beyond the limits of standard optics. In this review article, the recent developments and current status of photonic quantum information technology are overviewed based on the author’s past and recent works. PMID:26755398

Photonic quantum information: science and technology.

PubMed

Takeuchi, Shigeki

2016-01-01

Recent technological progress in the generation, manipulation and detection of individual single photons has opened a new scientific field of photonic quantum information. This progress includes the realization of single photon switches, photonic quantum circuits with specific functions, and the application of novel photonic states to novel optical metrology beyond the limits of standard optics. In this review article, the recent developments and current status of photonic quantum information technology are overviewed based on the author's past and recent works.

Hot-Electron Photon Counters for Detecting Terahertz Photons

NASA Technical Reports Server (NTRS)

Karasik, Boris; Sergeyev, Andrei

2005-01-01

A document proposes the development of hot-electron photon counters (HEPCs) for detecting terahertz photons in spaceborne far-infrared astronomical instruments. These would be superconducting- transition-edge devices: they would contain superconducting bridges that would have such low heat capacities that single terahertz photons would cause transient increases in their electron temperatures through the superconducting- transition range, thereby yielding measurable increases in electrical resistance. Single devices or imaging arrays of the devices would be fabricated as submicron-sized bridges made from films of disordered Ti (which has a superconducting- transition temperature of .0.35 K) between Nb contacts on bulk silicon or sapphire substrates. In operation, these devices would be cooled to a temperature of .0.3 K. The proposed devices would cost less to fabricate and operate, relative to integrating bolometers of equal sensitivity, which must be operated at a temperature of approx. = 0.1 K.

Localization control of few-photon states in parity-symmetric ‘photonic molecules’ under balanced pumping

NASA Astrophysics Data System (ADS)

Bentley, C. D. B.; Celestino, A.; Yacomotti, A. M.; El-Ganainy, R.; Eisfeld, A.

2018-06-01

We theoretically investigate the problem of localization control of few-photon states in driven-dissipative parity-symmetric photonic molecules. Photonic molecules are multi-cavity photonic systems. We show that a quantum feedback loop can utilize the information of the spontaneously-emitted photons from each cavity to induce asymmetric photon population in the cavities, while maintaining a balanced pump that respects parity symmetry. To better understand the system’s behavior, we characterize the degree of asymmetry as a function of the coupling between the two optical cavities. Contrary to intuitive expectations, we find that in some regimes the coupling can enhance the population asymmetry. We also show that these results are robust against experimental imperfections and limitations such as detection efficiency.

Photon statistics as an interference phenomenon.

PubMed

Mehringer, Thomas; Mährlein, Simon; von Zanthier, Joachim; Agarwal, Girish S

2018-05-15

Interference of light fields, first postulated by Young, is one of the fundamental pillars of physics. Dirac extended this observation to the quantum world by stating that each photon interferes only with itself. A precondition for interference to occur is that no welcher-weg information labels the paths the photon takes; otherwise, the interference vanishes. This remains true, even if two-photon interference is considered, e.g., in the Hong-Ou-Mandel-experiment. Here, the two photons interfere only if they are indistinguishable, e.g., in frequency, momentum, polarization, and time. Less known is the fact that two-photon interference and photon indistinguishability also determine the photon statistics in the overlapping light fields of two independent sources. As a consequence, measuring the photon statistics in the far field of two independent sources reveals the degree of indistinguishability of the emitted photons. In this Letter, we prove this statement in theory using a quantum mechanical treatment. We also demonstrate the outcome experimentally with a simple setup consisting of two statistically independent thermal light sources with adjustable polarizations. We find that the photon statistics vary indeed as a function of the polarization settings, the latter determining the degree of welcher-weg information of the photons emanating from the two sources.

REVIEW: Optics of globular photonic crystals

NASA Astrophysics Data System (ADS)

Gorelik, V. S.

2007-05-01

The results of experimental and theoretical studies of the optical properties of globular photonic crystals - new physical objects having a crystal structure with the lattice period exceeding considerably the atomic size, are presented. As globular photonic crystals, artificial opal matrices consisting of close-packed silica globules of diameter ~200 nm were used. The reflection spectra of these objects characterising the parameters of photonic bands existing in these crystals in the visible spectral region are presented. The idealised models of the energy band structure of photonic crystals investigated in the review give analytic dispersion dependences for the group velocity and the effective photon mass in a globular photonic crystal. The characteristics of secondary emission excited in globular photonic crystals by monochromatic and broadband radiation are presented. The results of investigations of single-photon-excited delayed scattering of light observed in globular photonic crystals exposed to cw UV radiation and radiation from a repetitively pulsed copper vapour laser are presented. The possibilities of using globular photonic crystals as active media for lasing in different spectral regions are considered. It is proposed to use globular photonic crystals as sensitive sensors in optoelectronic devices for molecular analysis of organic and inorganic materials by the modern methods of laser spectroscopy. The results of experimental studies of spontaneous and stimulated globular scattering of light are discussed. The conditions for observing resonance and two-photon-excited delayed scattering of light are found. The possibility of accumulation and localisation of the laser radiation energy inside a globular photonic crystal is reported.

Data acquisition system for the Belle experiment

NASA Astrophysics Data System (ADS)

Nakao, M.; Yamauchi, M.; Suzuki, S. Y.; Itoh, R.; Fujii, H.

2000-04-01

We built a data acquisition system for the Belle experiment at the KEK B-factory. The system is designed to record the signals from the detectors at 500 Hz trigger rate with a less than 10% dead time fraction. A typical event size is 30 kbyte, which corresponds to a data transfer rate of 15 Mbyte/s. Main components are two kinds of detector readout systems, an event builder, an online computer farm and a data storage system. The system has been reliably in operation at the design performance for a half year. We have completed cosmic-ray data taking for 2.5 months and have started physics data taking on Jun. 1, 1999.

Efficient fiber-coupled single-photon source based on quantum dots in a photonic-crystal waveguide

PubMed Central

DAVEAU, RAPHAËL S.; BALRAM, KRISHNA C.; PREGNOLATO, TOMMASO; LIU, JIN; LEE, EUN H.; SONG, JIN D.; VERMA, VARUN; MIRIN, RICHARD; NAM, SAE WOO; MIDOLO, LEONARDO; STOBBE, SØREN; SRINIVASAN, KARTIK; LODAHL, PETER

2017-01-01

Many photonic quantum information processing applications would benefit from a high brightness, fiber-coupled source of triggered single photons. Here, we present a fiber-coupled photonic-crystal waveguide single-photon source relying on evanescent coupling of the light field from a tapered out-coupler to an optical fiber. A two-step approach is taken where the performance of the tapered out-coupler is recorded first on an independent device containing an on-chip reflector. Reflection measurements establish that the chip-to-fiber coupling efficiency exceeds 80 %. The detailed characterization of a high-efficiency photonic-crystal waveguide extended with a tapered out-coupling section is then performed. The corresponding overall single-photon source efficiency is 10.9 % ± 2.3 %, which quantifies the success probability to prepare an exciton in the quantum dot, couple it out as a photon in the waveguide, and subsequently transfer it to the fiber. The applied out-coupling method is robust, stable over time, and broadband over several tens of nanometers, which makes it a highly promising pathway to increase the efficiency and reliability of planar chip-based single-photon sources. PMID:28584859

A distribution-free multi-factorial profiler for harvesting information from high-density screenings.

PubMed

Besseris, George J

2013-01-01

Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1) easy to grasp, 2) well-explained test-power properties, 3) distribution-free, 4) sparsity-free, 5) calibration-free, 6) simulation-free, 7) easy to implement, and 8) expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process.

Multilevel Factorial Experiments for Developing Behavioral Interventions: Power, Sample Size, and Resource Considerations†

PubMed Central

Dziak, John J.; Nahum-Shani, Inbal; Collins, Linda M.

2012-01-01

Factorial experimental designs have many potential advantages for behavioral scientists. For example, such designs may be useful in building more potent interventions, by helping investigators to screen several candidate intervention components simultaneously and decide which are likely to offer greater benefit before evaluating the intervention as a whole. However, sample size and power considerations may challenge investigators attempting to apply such designs, especially when the population of interest is multilevel (e.g., when students are nested within schools, or employees within organizations). In this article we examine the feasibility of factorial experimental designs with multiple factors in a multilevel, clustered setting (i.e., of multilevel multifactor experiments). We conduct Monte Carlo simulations to demonstrate how design elements such as the number of clusters, the number of lower-level units, and the intraclass correlation affect power. Our results suggest that multilevel, multifactor experiments are feasible for factor-screening purposes, because of the economical properties of complete and fractional factorial experimental designs. We also discuss resources for sample size planning and power estimation for multilevel factorial experiments. These results are discussed from a resource management perspective, in which the goal is to choose a design that maximizes the scientific benefit using the resources available for an investigation. PMID:22309956

A Distribution-Free Multi-Factorial Profiler for Harvesting Information from High-Density Screenings

PubMed Central

Besseris, George J.

2013-01-01

Data screening is an indispensable phase in initiating the scientific discovery process. Fractional factorial designs offer quick and economical options for engineering highly-dense structured datasets. Maximum information content is harvested when a selected fractional factorial scheme is driven to saturation while data gathering is suppressed to no replication. A novel multi-factorial profiler is presented that allows screening of saturated-unreplicated designs by decomposing the examined response to its constituent contributions. Partial effects are sliced off systematically from the investigated response to form individual contrasts using simple robust measures. By isolating each time the disturbance attributed solely to a single controlling factor, the Wilcoxon-Mann-Whitney rank stochastics are employed to assign significance. We demonstrate that the proposed profiler possesses its own self-checking mechanism for detecting a potential influence due to fluctuations attributed to the remaining unexplainable error. Main benefits of the method are: 1) easy to grasp, 2) well-explained test-power properties, 3) distribution-free, 4) sparsity-free, 5) calibration-free, 6) simulation-free, 7) easy to implement, and 8) expanded usability to any type and size of multi-factorial screening designs. The method is elucidated with a benchmarked profiling effort for a water filtration process. PMID:24009744

Multilevel factorial experiments for developing behavioral interventions: power, sample size, and resource considerations.

PubMed

Dziak, John J; Nahum-Shani, Inbal; Collins, Linda M

2012-06-01

Factorial experimental designs have many potential advantages for behavioral scientists. For example, such designs may be useful in building more potent interventions by helping investigators to screen several candidate intervention components simultaneously and to decide which are likely to offer greater benefit before evaluating the intervention as a whole. However, sample size and power considerations may challenge investigators attempting to apply such designs, especially when the population of interest is multilevel (e.g., when students are nested within schools, or when employees are nested within organizations). In this article, we examine the feasibility of factorial experimental designs with multiple factors in a multilevel, clustered setting (i.e., of multilevel, multifactor experiments). We conduct Monte Carlo simulations to demonstrate how design elements-such as the number of clusters, the number of lower-level units, and the intraclass correlation-affect power. Our results suggest that multilevel, multifactor experiments are feasible for factor-screening purposes because of the economical properties of complete and fractional factorial experimental designs. We also discuss resources for sample size planning and power estimation for multilevel factorial experiments. These results are discussed from a resource management perspective, in which the goal is to choose a design that maximizes the scientific benefit using the resources available for an investigation. (c) 2012 APA, all rights reserved

Effects of occupational exposures and smoking on lung function in tile factory workers.

PubMed

Jaakkola, Maritta S; Sripaiboonkij, Penpatra; Jaakkola, Jouni J K

2011-02-01

The aims of this study were to investigate the relations of occupational exposures in tile industry to lung function and to evaluate potential interaction between smoking and tile dust exposure containing silica. A cross-sectional study of 232 workers (response rate 100%) in a tile factory and 76 office workers (response rate 73%) from four factories in Thailand was conducted in 2006-2007. Participants answered a questionnaire and performed spirometry. Factory workers had lower spirometric functions than office workers, especially those with high dust exposure. There was a dose-response relation between duration of dust exposure and FEV1 and FVC, the adjusted effect of ≥ 21 years of exposure on FEV1 being -240 ml (-100 to -380) and on FVC -300 ml (-140 to -460). The adverse effect of dust on lung function was larger in current smokers suggesting synergism between smoking and tile dust exposure. This study provides evidence that long-term exposure to dust in tile industry is related to lung function reduction. There was a suggestion of synergistic effect between dust exposure and smoking. Tile factories should consider measures to reduce dust exposure and arrange spirometry surveillance for workers with such exposure. Smoking cessation should be promoted to prevent harmful effects of occupational tile dust exposure.

A novel photonic oscillator

NASA Technical Reports Server (NTRS)

Yao, X. S.; Maleki, L.

1995-01-01

We report a novel oscillator for photonic RF systems. This oscillator is capable of generating high-frequency signals up to 70 GHz in both electrical and optical domains and is a special voltage-controlled oscillator with an optical output port. It can be used to make a phase-locked loop (PLL) and perform all functions that a PLL is capable of for photonic systems. It can be synchronized to a reference source by means of optical injection locking, electrical injection locking, and PLL. It can also be self-phase locked and self-injection locked to generate a high-stability photonic RF reference. Its applications include high-frequency reference regeneration and distribution, high-gain frequency multiplication, comb-frequecy and square-wave generation, carrier recovery, and clock recovery. We anticipate that such photonic voltage-controlled oscillators (VCOs) will be as important to photonic RF systems as electrical VCOs are to electrical RF systems.

Nanofiber quantum photonics

NASA Astrophysics Data System (ADS)

Nayak, Kali P.; Sadgrove, Mark; Yalla, Ramachandrarao; Le Kien, Fam; Hakuta, Kohzo

2018-07-01

Recent advances in the coherent control of single quanta of light, photons, is a topic of prime interest, and is discussed under the banner of quantum photonics. In the last decade, the subwavelength diameter waist of a tapered optical fiber, referred to as an optical nanofiber, has opened promising new avenues in the field of quantum optics, paving the way toward a versatile platform for quantum photonics applications. The key feature of the technique is that the optical field can be tightly confined in the transverse direction while propagating over long distances as a guided mode and enabling strong interaction with the surrounding medium in the evanescent region. This feature has led to surprising possibilities to manipulate single atoms and fiber-guided photons, e.g. the efficient channeling of emission from single atoms and solid-state quantum emitters into the fiber-guided modes, high optical depth with a few atoms around the nanofiber, trapping atoms around a nanofiber, and atomic memories for fiber-guided photons. Furthermore, implementing a moderate longitudinal confinement in nanofiber cavities has enabled the strong coupling regime of cavity quantum electrodynamics to be reached, and the long-range dipole–dipole interaction between quantum emitters mediated by the nanofiber offers a platform for quantum nonlinear optics with an ensemble of atoms. In addition, the presence of a longitudinal component of the guided field has led to unique capabilities for chiral light–matter interactions on nanofibers. In this article, we review the key developments of the nanofiber technology toward a vision for quantum photonics on an all-fiber interface.

Interferometric Quantum-Nondemolition Single-Photon Detectors

NASA Technical Reports Server (NTRS)

Kok, Peter; Lee, Hwang; Dowling, Jonathan

2007-01-01

Two interferometric quantum-nondemolition (QND) devices have been proposed: (1) a polarization-independent device and (2) a polarization-preserving device. The prolarization-independent device works on an input state of up to two photons, whereas the polarization-preserving device works on a superposition of vacuum and single- photon states. The overall function of the device would be to probabilistically generate a unique detector output only when its input electromagnetic mode was populated by a single photon, in which case its output mode would also be populated by a single photon. Like other QND devices, the proposed devices are potentially useful for a variety of applications, including such areas of NASA interest as quantum computing, quantum communication, detection of gravity waves, as well as pedagogical demonstrations of the quantum nature of light. Many protocols in quantum computation and quantum communication require the possibility of detecting a photon without destroying it. The only prior single- photon-detecting QND device is based on quantum electrodynamics in a resonant cavity and, as such, it depends on the photon frequency. Moreover, the prior device can distinguish only between one photon and no photon. The proposed interferometric QND devices would not depend on frequency and could distinguish between (a) one photon and (b) zero or two photons. The first proposed device is depicted schematically in Figure 1. The input electromagnetic mode would be a superposition of a zero-, a one-, and a two-photon quantum state. The overall function of the device would be to probabilistically generate a unique detector output only when its input electromagnetic mode was populated by a single photon, in which case its output mode also would be populated by a single photon.

Replicating systems concepts: Self-replicating lunar factory and demonstration

NASA Technical Reports Server (NTRS)

1982-01-01

Automation of lunar mining and manufacturing facility maintenance and repair is addressed. Designing the factory as an automated, multiproduct, remotely controlled, reprogrammable Lunar Manufacturing Facility capable of constructing duplicates of itself which would themselves be capable of further replication is proposed.

Characterizing multi-photon quantum interference with practical light sources and threshold single-photon detectors

NASA Astrophysics Data System (ADS)

Navarrete, Álvaro; Wang, Wenyuan; Xu, Feihu; Curty, Marcos

2018-04-01

The experimental characterization of multi-photon quantum interference effects in optical networks is essential in many applications of photonic quantum technologies, which include quantum computing and quantum communication as two prominent examples. However, such characterization often requires technologies which are beyond our current experimental capabilities, and today's methods suffer from errors due to the use of imperfect sources and photodetectors. In this paper, we introduce a simple experimental technique to characterize multi-photon quantum interference by means of practical laser sources and threshold single-photon detectors. Our technique is based on well-known methods in quantum cryptography which use decoy settings to tightly estimate the statistics provided by perfect devices. As an illustration of its practicality, we use this technique to obtain a tight estimation of both the generalized Hong‑Ou‑Mandel dip in a beamsplitter with six input photons and the three-photon coincidence probability at the output of a tritter.

10 years of protein crystallography at AR-NW12A beamline

NASA Astrophysics Data System (ADS)

Chavas, L. M. G.; Yamada, Y.; Hiraki, M.; Igarashi, N.; Matsugaki, N.; Wakatsuki, S.

2013-03-01

The exponential growth of protein crystallography can be observed in the continuously increasing demand for synchrotron beam time, both from academic and industrial users. Nowadays, the screening of a profusion of sample crystals for more and more projects is being implemented by taking advantage of fully automated procedures at every level of the experiments. The insertion device AR-NW12A beamline is one of the five macromolecular crystallography (MX) beamlines at the Photon Factory (PF). Currently the oldest MX beamline operational at the High Energy Accelerator Research Organization (KEK), the end-station was launched in 2001 as part of an upgrade of the PF Advanced Ring. Since its commissioning, AR-NW12A has been operating as a high-throughput beamline, slowly evolving to a multipurpose end-station for MX experiments. The development of the beamline took place about a decade ago, in parallel with a drastic development of protein crystallography and more general synchrotron technology. To keep the beamline up-to-date and competitive with other MX stations in Japan and worldwide, new features have been constantly added, with the goal of user friendliness of the various beamline optics and other instruments. Here we describe the evolution of AR-NW12A for its tenth anniversary. We also discuss the plans for upgrades for AR-NW12A, the future objectives in terms of the beamline developments, and especially the strong desire to open the beamline to a larger user community.

Training Factory Workers: Three Case Studies. Contractor Report.

ERIC Educational Resources Information Center

Hirschhorn, Larry D.

Case studies examined the context and impact of training in three factories: a bakery, a circuit assembly plant, and a plant that produces microchips. Cookie-Foods, Inc. used Statistical Process Control (SPC) and a course on problem solving to increase the operators' productivity. Impact of the SPC program was limited, because workers who…

Learning Factory--Assembling Learning Content with a Framework

ERIC Educational Resources Information Center

Steininger, Peter

2016-01-01

Many of the challenges currently facing lectures are symptoms of problems with learning content creation, development and presentation. Learning Factory solves these problems by integrating critical innovations that have been proven over the last ten to twenty years in different industrial areas, but have not yet been brought or ported together in…

Photonic Landau levels on cones

NASA Astrophysics Data System (ADS)

Schine, Nathan; Ryou, Albert; Gromov, Andrey; Sommer, Ariel; Simon, Jonathan

2016-05-01

We present the first experimental realization of a bulk magnetic field for optical photons. By using a non-planar ring resonator, we induce an image rotation on each round trip through the resonator. This results in a Coriolis/Lorentz force and a centrifugal anticonfining force, the latter of which is cancelled by mirror curvature. Using a digital micromirror device to control both amplitude and phase, we inject arbitrary optical modes into our resonator. Spatial- and energy- resolved spectroscopy tracks photonic eigenstates as residual trapping is reduced, and we observe photonic Landau levels as the eigenstates become degenerate. We show that there is a conical geometry of the resulting manifold for photon dynamics and present a measurement of the local density of states that is consistent with Landau levels on a cone. While our work already demonstrates an integer quantum Hall material composed of photons, we have ensured compatibility with strong photon-photon interactions, which will allow quantum optical studies of entanglement and correlation in manybody systems including fractional quantum Hall fluids.

Hybrid colloidal plasmonic-photonic crystals.

PubMed

Romanov, Sergei G; Korovin, Alexander V; Regensburger, Alois; Peschel, Ulf

2011-06-17

We review the recently emerged class of hybrid metal-dielectric colloidal photonic crystals. The hybrid approach is understood as the combination of a dielectric photonic crystal with a continuous metal film. It allows to achieve a strong modification of the optical properties of photonic crystals by involving the light scattering at electronic excitations in the metal component into moulding of the light flow in series to the diffraction resonances occurring in the body of the photonic crystal. We consider different realizations of hybrid plasmonic-photonic crystals based on two- and three-dimensional colloidal photonic crystals in association with flat and corrugated metal films. In agreement with model calculations, different resonance phenomena determine the optical response of hybrid crystals leading to a broadly tuneable functionality of these crystals. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Entangled-photon coincidence fluorescence imaging

PubMed Central

Scarcelli, Giuliano; Yun, Seok H.

2009-01-01

We describe fluorescence imaging using the second-order correlation of entangled photon pairs. The proposed method is based on the principle that one photon of the pair carries information on where the other photon has been absorbed and has produced fluorescence in a sample. Because fluorescent molecules serve as “detectors” breaking the entanglement, multiply-scattered fluorescence photons within the sample do not cause image blur. We discuss experimental implementations. PMID:18825257

Bose-Einstein condensation of photons from the thermodynamic limit to small photon numbers

NASA Astrophysics Data System (ADS)

Nyman, Robert A.; Walker, Benjamin T.

2018-03-01

Photons can come to thermal equilibrium at room temperature by scattering multiple times from a fluorescent dye. By confining the light and dye in a microcavity, a minimum energy is set and the photons can then show Bose-Einstein condensation. We present here the physical principles underlying photon thermalization and condensation, and review the literature on the subject. We then explore the 'small' regime where very few photons are needed for condensation. We compare thermal equilibrium results to a rate-equation model of microlasers, which includes spontaneous emission into the cavity, and we note that small systems result in ambiguity in the definition of threshold.

A photonic chip based frequency discriminator for a high performance microwave photonic link.

PubMed

Marpaung, David; Roeloffzen, Chris; Leinse, Arne; Hoekman, Marcel

2010-12-20

We report a high performance phase modulation direct detection microwave photonic link employing a photonic chip as a frequency discriminator. The photonic chip consists of five optical ring resonators (ORRs) which are fully programmable using thermo-optical tuning. In this discriminator a drop-port response of an ORR is cascaded with a through response of another ORR to yield a linear phase modulation (PM) to intensity modulation (IM) conversion. The balanced photonic link employing the PM to IM conversion exhibits high second-order and third-order input intercept points of + 46 dBm and + 36 dBm, respectively, which are simultaneously achieved at one bias point.

46 CFR 162.050-13 - Factory production and inspection.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Factory production and inspection. 162.050-13 Section 162.050-13 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Pollution Prevention Equipment § 162...

Photonically engineered incandescent emitter

DOEpatents

Gee, James M.; Lin, Shawn-Yu; Fleming, James G.; Moreno, James B.

2003-08-26

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Photonically Engineered Incandescent Emitter

DOEpatents

Gee, James M.; Lin, Shawn-Yu; Fleming, James G.; Moreno, James B.

2005-03-22

A photonically engineered incandescence is disclosed. The emitter materials and photonic crystal structure can be chosen to modify or suppress thermal radiation above a cutoff wavelength, causing the emitter to selectively emit in the visible and near-infrared portions of the spectrum. An efficient incandescent lamp is enabled thereby. A method for fabricating a three-dimensional photonic crystal of a structural material, suitable for the incandescent emitter, is also disclosed.

Photonic-magnonic crystals: Multifunctional periodic structures for magnonic and photonic applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kłos, J. W., E-mail: klos@amu.edu.pl; Krawczyk, M.; Dadoenkova, Yu. S.

2014-05-07

We investigate the properties of a photonic-magnonic crystal, a complex multifunctional one-dimensional structure with magnonic and photonic band gaps in the GHz and PHz frequency ranges for spin waves and light, respectively. The system consists of periodically distributed dielectric magnetic slabs of yttrium iron garnet and nonmagnetic spacers with an internal structure of alternating TiO{sub 2} and SiO{sub 2} layers which form finite-size dielectric photonic crystals. We show that the spin-wave coupling between the magnetic layers, and thus the formation of the magnonic band structure, necessitates a nonzero in-plane component of the spin-wave wave vector. A more complex structure perceivedmore » by light is evidenced by the photonic miniband structure and the transmission spectra in which we have observed transmission peaks related to the repetition of the magnetic slabs in the frequency ranges corresponding to the photonic band gaps of the TiO{sub 2}/SiO{sub 2} stack. Moreover, we show that these modes split to very high sharp (a few THz wide) subpeaks in the transmittance spectra. The proposed novel multifunctional artificial crystals can have interesting applications and be used for creating common resonant cavities for spin waves and light to enhance the mutual influence between them.« less

A Market-Based Approach to Multi-factory Scheduling

NASA Astrophysics Data System (ADS)

Vytelingum, Perukrishnen; Rogers, Alex; MacBeth, Douglas K.; Dutta, Partha; Stranjak, Armin; Jennings, Nicholas R.

In this paper, we report on the design of a novel market-based approach for decentralised scheduling across multiple factories. Specifically, because of the limitations of scheduling in a centralised manner - which requires a center to have complete and perfect information for optimality and the truthful revelation of potentially commercially private preferences to that center - we advocate an informationally decentralised approach that is both agile and dynamic. In particular, this work adopts a market-based approach for decentralised scheduling by considering the different stakeholders representing different factories as self-interested, profit-motivated economic agents that trade resources for the scheduling of jobs. The overall schedule of these jobs is then an emergent behaviour of the strategic interaction of these trading agents bidding for resources in a market based on limited information and their own preferences. Using a simple (zero-intelligence) bidding strategy, we empirically demonstrate that our market-based approach achieves a lower bound efficiency of 84%. This represents a trade-off between a reasonable level of efficiency (compared to a centralised approach) and the desirable benefits of a decentralised solution.

Photon-number discrimination without a photon counter and its application to reconstructing non-Gaussian states

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chrzanowski, H. M.; Bernu, J.; Sparkes, B. M.

2011-11-15

The nonlinearity of a conditional photon-counting measurement can be used to ''de-Gaussify'' a Gaussian state of light. Here we present and experimentally demonstrate a technique for photon-number resolution using only homodyne detection. We then apply this technique to inform a conditional measurement, unambiguously reconstructing the statistics of the non-Gaussian one- and two-photon-subtracted squeezed vacuum states. Although our photon-number measurement relies on ensemble averages and cannot be used to prepare non-Gaussian states of light, its high efficiency, photon-number-resolving capabilities, and compatibility with the telecommunications band make it suitable for quantum-information tasks relying on the outcomes of mean values.

Femtosecond Photon-Counting Receiver

NASA Technical Reports Server (NTRS)

Krainak, Michael A.; Rambo, Timothy M.; Yang, Guangning; Lu, Wei; Numata, Kenji

2016-01-01

An optical correlation receiver is described that provides ultra-precise distance and/or time/pulse-width measurements even for weak (single photons) and short (femtosecond) optical signals. A new type of optical correlation receiver uses a fourth-order (intensity) interferometer to provide micron distance measurements even for weak (single photons) and short (femtosecond) optical signals. The optical correlator uses a low-noise-integrating detector that can resolve photon number. The correlation (range as a function of path delay) is calculated from the variance of the photon number of the difference of the optical signals on the two detectors. Our preliminary proof-of principle data (using a short-pulse diode laser transmitter) demonstrates tens of microns precision.

Femtosecond Photon-Counting Receiver

NASA Technical Reports Server (NTRS)

Krainak, Michael A.; Rambo, Timothy M.; Yang, Guangning; Lu, Wei; Numata, Kenji

2016-01-01

An optical correlation receiver is described that provides ultra-precise distance and/or time-pulse-width measurements even for weak (single photons) and short (femtosecond) optical signals. A new type of optical correlation receiver uses a fourth-order (intensity) interferometer to provide micron distance measurements even for weak (single photons) and short (femtosecond) optical signals. The optical correlator uses a low-noise-integrating detector that can resolve photon number. The correlation (range as a function of path delay) is calculated from the variance of the photon number of the difference of the optical signals on the two detectors. Our preliminary proof-of principle data (using a short-pulse diode laser transmitter) demonstrates tens of microns precision.

Optomechanical measurement of photon spin angular momentum and optical torque in integrated photonic devices

PubMed Central

He, Li; Li, Huan; Li, Mo

2016-01-01

Photons carry linear momentum and spin angular momentum when circularly or elliptically polarized. During light-matter interaction, transfer of linear momentum leads to optical forces, whereas transfer of angular momentum induces optical torque. Optical forces including radiation pressure and gradient forces have long been used in optical tweezers and laser cooling. In nanophotonic devices, optical forces can be significantly enhanced, leading to unprecedented optomechanical effects in both classical and quantum regimes. In contrast, to date, the angular momentum of light and the optical torque effect have only been used in optical tweezers but remain unexplored in integrated photonics. We demonstrate the measurement of the spin angular momentum of photons propagating in a birefringent waveguide and the use of optical torque to actuate rotational motion of an optomechanical device. We show that the sign and magnitude of the optical torque are determined by the photon polarization states that are synthesized on the chip. Our study reveals the mechanical effect of photon’s polarization degree of freedom and demonstrates its control in integrated photonic devices. Exploiting optical torque and optomechanical interaction with photon angular momentum can lead to torsional cavity optomechanics and optomechanical photon spin-orbit coupling, as well as applications such as optomechanical gyroscopes and torsional magnetometry. PMID:27626072

High-speed photon-counting x-ray computed tomography system utilizing a multipixel photon counter

NASA Astrophysics Data System (ADS)

Sato, Eiichi; Enomoto, Toshiyuki; Watanabe, Manabu; Hitomi, Keitaro; Takahashi, Kiyomi; Sato, Shigehiro; Ogawa, Akiro; Onagawa, Jun

2009-07-01

High-speed photon counting is useful for discriminating photon energy and for decreasing absorbed dose for patients in medical radiography, and the counting is usable for constructing an x-ray computed tomography (CT) system. A photon-counting x-ray CT system is of the first generation type and consists of an x-ray generator, a turn table, a translation stage, a two-stage controller, a multipixel photon counter (MPPC) module, a 1.0-mm-thick LSO crystal (scintillator), a counter card (CC), and a personal computer (PC). Tomography is accomplished by repeating the linear scanning and the rotation of an object, and projection curves of the object are obtained by the linear scanning using the detector consisting of a MPPC module and the LSO. The pulses of the event signal from the module are counted by the CC in conjunction with the PC. The lower level of the photon energy is roughly determined by a comparator circuit in the module, and the unit of the level is the photon equivalent (pe). Thus, the average photon energy of the x-ray spectra increases with increasing the lower-level voltage of the comparator. The maximum count rate was approximately 20 Mcps, and energy-discriminated CT was roughly carried out.

High-fidelity frequency down-conversion of visible entangled photon pairs with superconducting single-photon detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ikuta, Rikizo; Kato, Hiroshi; Kusaka, Yoshiaki

We experimentally demonstrate a high-fidelity visible-to-telecommunicationwavelength conversion of a photon by using a solid-state-based difference frequency generation. In the experiment, one half of a pico-second visible entangled photon pair at 780 nm is converted to a 1522-nm photon. Using superconducting single-photon detectors with low dark count rates and small timing jitters, we observed a fidelity of 0.93±0.04 after the wavelength conversion.

Platinum Acetylide Two-Photon Chromophores (Preprint)

DTIC Science & Technology

2007-04-01

nonlinear photonics,6-s microfabrication,9,10 fluorescence imaging, II and photodynamic therapy.12Instantaneous absorption of two lower energy photons...results in initiation of the same photophysical processes as one-photon absorption (lP A) of one high- energy photon. This is advantageous for two...reasons. The first is that because of the use of a lower energy photon a material will be guarded from ionization effects from multiphoton absorption in

Design of Experiments with Multiple Independent Variables: A Resource Management Perspective on Complete and Reduced Factorial Designs

PubMed Central

Collins, Linda M.; Dziak, John J.; Li, Runze

2009-01-01

An investigator who plans to conduct experiments with multiple independent variables must decide whether to use a complete or reduced factorial design. This article advocates a resource management perspective on making this decision, in which the investigator seeks a strategic balance between service to scientific objectives and economy. Considerations in making design decisions include whether research questions are framed as main effects or simple effects; whether and which effects are aliased (confounded) in a particular design; the number of experimental conditions that must be implemented in a particular design and the number of experimental subjects the design requires to maintain the desired level of statistical power; and the costs associated with implementing experimental conditions and obtaining experimental subjects. In this article four design options are compared: complete factorial, individual experiments, single factor, and fractional factorial designs. Complete and fractional factorial designs and single factor designs are generally more economical than conducting individual experiments on each factor. Although relatively unfamiliar to behavioral scientists, fractional factorial designs merit serious consideration because of their economy and versatility. PMID:19719358

Ultra-broadband photonic internet

NASA Astrophysics Data System (ADS)

Romaniuk, Ryszard S.

2011-06-01

In this paper, there is presented a review of our today's understanding of the ultimately broadband photonic Internet. A simple calculation is presented showing the estimate of the throughput of the core photonic network branches. Optoelectronic components, circuits, systems and signals, together with analogous electronic entities and common software layers, are building blocks of the contemporary Internet. Participation of photonics in development of the physical layer in the future Internet will probably increase. The photonics leads now to a better usage of the available bandwidth (increase of the spectral efficiency measured in Bit/s/Hz), increase in the transmission rate (from Gbps, via Tbps up to probably Pbps), increase in the transmission distance without signal regeneration (in distortion compensated active optical cables), increase in energy/power efficiency measured in W/Gbps, etc. Photonics may lead, in the future, to fully transparent optical networks and, thus, to essential increase in bandwidth and network reliability. It is expected that photonics (with biochemistry, electronics and mechatronics) may build psychological and physiological interface for humans to the future global network. The following optical signal multiplexing methods were considered, which are possible without O/E/O conversion: TDM-OTDM, FDM-CO-OFDM, OCDM-OCDMA, WDM-DWDM.

Data Processing Factory for the Sloan Digital Sky Survey

NASA Astrophysics Data System (ADS)

Stoughton, Christopher; Adelman, Jennifer; Annis, James T.; Hendry, John; Inkmann, John; Jester, Sebastian; Kent, Steven M.; Kuropatkin, Nickolai; Lee, Brian; Lin, Huan; Peoples, John, Jr.; Sparks, Robert; Tucker, Douglas; Vanden Berk, Dan; Yanny, Brian; Yocum, Dan

2002-12-01

The Sloan Digital Sky Survey (SDSS) data handling presents two challenges: large data volume and timely production of spectroscopic plates from imaging data. A data processing factory, using technologies both old and new, handles this flow. Distribution to end users is via disk farms, to serve corrected images and calibrated spectra, and a database, to efficiently process catalog queries. For distribution of modest amounts of data from Apache Point Observatory to Fermilab, scripts use rsync to update files, while larger data transfers are accomplished by shipping magnetic tapes commercially. All data processing pipelines are wrapped in scripts to address consecutive phases: preparation, submission, checking, and quality control. We constructed the factory by chaining these pipelines together while using an operational database to hold processed imaging catalogs. The science database catalogs all imaging and spectroscopic object, with pointers to the various external files associated with them. Diverse computing systems address particular processing phases. UNIX computers handle tape reading and writing, as well as calibration steps that require access to a large amount of data with relatively modest computational demands. Commodity CPUs process steps that require access to a limited amount of data with more demanding computations requirements. Disk servers optimized for cost per Gbyte serve terabytes of processed data, while servers optimized for disk read speed run SQLServer software to process queries on the catalogs. This factory produced data for the SDSS Early Data Release in June 2001, and it is currently producing Data Release One, scheduled for January 2003.

Roles of factorial noise in inducing bimodal gene expression

NASA Astrophysics Data System (ADS)

Liu, Peijiang; Yuan, Zhanjiang; Huang, Lifang; Zhou, Tianshou

2015-06-01

Some gene regulatory systems can exhibit bimodal distributions of mRNA or protein although the deterministic counterparts are monostable. This noise-induced bimodality is an interesting phenomenon and has important biological implications, but it is unclear how different sources of expression noise (each source creates so-called factorial noise that is defined as a component of the total noise) contribute separately to this stochastic bimodality. Here we consider a minimal model of gene regulation, which is monostable in the deterministic case. Although simple, this system contains factorial noise of two main kinds: promoter noise due to switching between gene states and transcriptional (or translational) noise due to synthesis and degradation of mRNA (or protein). To better trace the roles of factorial noise in inducing bimodality, we also analyze two limit models, continuous and adiabatic approximations, apart from the exact model. We show that in the case of slow gene switching, the continuous model where only promoter noise is considered can exhibit bimodality; in the case of fast switching, the adiabatic model where only transcriptional or translational noise is considered can also exhibit bimodality but the exact model cannot; and in other cases, both promoter noise and transcriptional or translational noise can cooperatively induce bimodality. Since slow gene switching and large protein copy numbers are characteristics of eukaryotic cells, whereas fast gene switching and small protein copy numbers are characteristics of prokaryotic cells, we infer that eukaryotic stochastic bimodality is induced mainly by promoter noise, whereas prokaryotic stochastic bimodality is induced primarily by transcriptional or translational noise.

EDITORIAL: Photonic Crystal Devices

NASA Astrophysics Data System (ADS)

Bhattacharya, Pallab K.

2007-05-01

The engineering of electromagnetic modes at optical frequencies in artificial dielectric structures with periodic and random variation of the refractive index, enabling control of the radiative properties of the materials and photon localization, was first proposed independently by Yablonovitch and John in 1987. It is possible to control the flow of light in the periodic dielectric structures, known as photonic crystals (PC). As light waves scatter within the photonic crystal, destructive interference cancels out light of certain wavelengths, thereby forming a photonic bandgap, similar to the energy bandgap for electron waves in a semiconductor. Photons whose energies lie within the gap cannot propagate through the periodic structure. This property can be used to make a low-loss cavity. If a point defect, such as one or more missing periods, is introduced into the periodic structure a region is obtained within which the otherwise forbidden wavelengths can be locally trapped. This property can be used to realize photonic microcavities. Similarly, a line of defects can serve as a waveguide. While the realization of three-dimensional (3D) photonic crystals received considerable attention initially, planar two-dimensional (2D) structures are currently favoured because of their relative ease of fabrication. 2D photonic crystal structures provide most of the functionality of 3D structures. These attributes have generated worldwide research and development of sub-μm and μm size active and passive photonic devices such as single-mode and non- classical light sources, guided wave devices, resonant cavity detection, and components for optical communication. More recently, photonic crystal guided wave devices are being investigated for application in microfludic and biochemical sensing. Photonic crystal devices have been realized with bulk, quantum well and quantum dot active regions. The Cluster of articles in this issue of Journal of Physics D: Applied Physics provides a

Properties of entangled photon pairs generated in one-dimensional nonlinear photonic-band-gap structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perina, Jan Jr.; Centini, Marco; Sibilia, Concita

We have developed a rigorous quantum model of spontaneous parametric down-conversion in a nonlinear 1D photonic-band-gap structure based upon expansion of the field into monochromatic plane waves. The model provides a two-photon amplitude of a created photon pair. The spectra of the signal and idler fields, their intensity profiles in the time domain, as well as the coincidence-count interference pattern in a Hong-Ou-Mandel interferometer are determined both for cw and pulsed pumping regimes in terms of the two-photon amplitude. A broad range of parameters characterizing the emitted down-converted fields can be used. As an example, a structure composed of 49more » layers of GaN/AlN is analyzed as a suitable source of photon pairs having high efficiency.« less

Industrial systems biology and its impact on synthetic biology of yeast cell factories.

PubMed

Fletcher, Eugene; Krivoruchko, Anastasia; Nielsen, Jens

2016-06-01

Engineering industrial cell factories to effectively yield a desired product while dealing with industrially relevant stresses is usually the most challenging step in the development of industrial production of chemicals using microbial fermentation processes. Using synthetic biology tools, microbial cell factories such as Saccharomyces cerevisiae can be engineered to express synthetic pathways for the production of fuels, biopharmaceuticals, fragrances, and food flavors. However, directing fluxes through these synthetic pathways towards the desired product can be demanding due to complex regulation or poor gene expression. Systems biology, which applies computational tools and mathematical modeling to understand complex biological networks, can be used to guide synthetic biology design. Here, we present our perspective on how systems biology can impact synthetic biology towards the goal of developing improved yeast cell factories. Biotechnol. Bioeng. 2016;113: 1164-1170. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

Long-term pulmonary complications of chemical weapons exposure in former poison gas factory workers.

PubMed

Nishimura, Yoshifumi; Iwamoto, Hiroshi; Ishikawa, Nobuhisa; Hattori, Noboru; Horimasu, Yasushi; Ohshimo, Shinichiro; Fujitaka, Kazunori; Kondo, Keiichi; Hamada, Hironobu; Awai, Kazuo; Kohno, Nobuoki

2016-07-01

Sulfur mustard (SM) and lewisite are vesicant chemical warfare agents that can cause skin blistering and chronic lung complications. During 1929-1945, a Japanese factory produced poisonous gases, which included SM, lewisite and other chemical weapons. The aim of this study was to investigate the chest computed tomography (CT) findings among long-term survivors who worked at this factory. During 2009-2012, we evaluated chest CT findings from 346 long-term survivors who worked at the poison gas factory. Skin lesions were used as an indicator of significant exposure to vesicant agents. Among the 346 individuals, 53 (15%) individuals experienced skin lesions while working at the factory, and chest CT revealed abnormal findings in 179 individuals (52%). Emphysema was the most common CT finding and was observed in 75 individuals (22%), while honeycombing was observed in 8 individuals (2%). Emphysema and honeycombing were more prevalent among individuals with skin lesions, compared to individuals without skin lesions. Multivariate analyses revealed significant associations between the presence of emphysema and skin lesions (p = 0.008). Among individuals who never smoked, individuals with skin lesions (n = 26) exhibited a significantly higher rate of emphysema, compared to individuals without skin lesions (n = 200) (35% versus 7%, respectively; p < 0.001). Among the long-term survivors who worked at the poison gas factory, a history of skin lesions was associated with the presence of emphysema, even among never smokers, which suggests that emphysema might be a long-term complication of exposure to chemical warfare agents.

Photon-phonon-photon transfer in optomechanics

PubMed Central

Rakhubovsky, Andrey A.; Filip, Radim

2017-01-01

We consider transfer of a highly nonclassical quantum state through an optomechanical system. That is we investigate a protocol consisting of sequential upload, storage and reading out of the quantum state from a mechanical mode of an optomechanical system. We show that provided the input state is in a test-bed single-photon Fock state, the Wigner function of the recovered state can have negative values at the origin, which is a manifest of nonclassicality of the quantum state of the macroscopic mechanical mode and the overall transfer protocol itself. Moreover, we prove that the recovered state is quantum non-Gaussian for wide range of setup parameters. We verify that current electromechanical and optomechanical experiments can test this complete transfer of single photon. PMID:28436461

Photon detector system

DOEpatents

Ekstrom, Philip A.

1981-01-01

A photon detector includes a semiconductor device, such as a Schottky barrier diode, which has an avalanche breakdown characteristic. The diode is cooled to cryogenic temperatures to eliminate thermally generated charge carriers from the device. The diode is then biased to a voltage level exceeding the avalanche breakdown threshold level such that, upon receipt of a photon, avalanche breakdown occurs. This breakdown is detected by appropriate circuitry which thereafter reduces the diode bias potential to a level below the avalanche breakdown threshold level to terminate the avalanche condition. Subsequently, the bias potential is reapplied to the diode in preparation for detection of a subsequently received photon.

Searching for Heavy Photons with Detached Verices in the Heavy Photon Search Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szumila-Vance, Holly

The Jefferson Lab Heavy Photon Search (HPS) experiment is searching for a hypothetical massive particle called the heavy photon which could mediate a dark electromagnetic-type force. If heavy photons kinetically mix with Standard Model photons, they may be radiated by electrons scattering from a heavy nucleus and then decay to e+e- pairs. HPS uniquely searches for heavy photons that either decay at the target or a measurable distance after. The experiment utilizes a silicon vertex tracker (SVT) for momentum and vertex reconstruction, together with an electromagnetic calorimeter for measuring particle energies and triggering events. The HPS experiment took its firstmore » data during the spring 2015 engineering run using a 1 GeV electron beam incident on a tungsten target and its second data in the spring of 2016 at a beam energy of 2.3 GeV. The 2015 run obtained two days of production data that was used for the first physics results. The analysis of the data was conducted as a blinded analysis by tuning cuts on 10% of the data. This dissertation discusses the displaced vertex search for heavy photons in the 2015 engineering run. It describes the theoretical motivation for looking for heavy photons and provides an overview of the HPS experimental design and performance. The performance details of the experiment are primarily derived from the 2015 engineering run with some discussion from the higher energy running in 2016. This dissertation further discusses the cuts used to optimize the displaced vertex search and the results of the search. The displaced vertex search did not set a limit on the heavy photon but did validate the methodology for conducting the search. Finally, we used the full data set to make projections and guide future analyses.« less

National Photonics Skills Standard for Technicians.

ERIC Educational Resources Information Center

Center for Occupational Research and Development, Inc., Waco, TX.

This document defines "photonics" as the generation, manipulation, transport, detection, and use of light information and energy whose quantum unit is the photon. The range of applications of photonics extends from energy generation to detection to communication and information processing. Photonics is at the heart of today's…

Photonic layered media

DOEpatents

Fleming, James G.; Lin, Shawn-Yu

2002-01-01

A new class of structured dielectric media which exhibit significant photonic bandstructure has been invented. The new structures, called photonic layered media, are easy to fabricate using existing layer-by-layer growth techniques, and offer the ability to significantly extend our practical ability to tailor the properties of such optical materials.

Factorial Design: An Eight Factor Experiment Using Paper Helicopters

NASA Technical Reports Server (NTRS)

Kozma, Michael

1996-01-01

The goal of this paper is to present the analysis of the multi-factor experiment (factorial design) conducted in EG490, Junior Design at Loyola College in Maryland. The discussion of this paper concludes the experimental analysis and ties the individual class papers together.

Particle identification at an asymmetric B Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coyle, P.; Eigen, G.; Hitlin, D.

1991-09-01

Particle identification systems are an important component of any detector at a high-luminosity, asymmetric B Factory. In particular, excellent hadron identification is required to probe CP violation in B{sup 0} decays to CP eigenstates. The particle identification systems discussed below also provide help in separating leptons from hadrons at low momenta. We begin this chapter with a discussion of the physics motivation for providing particle identification, the inherent limitations due to interactions and decays in flight, and the requirements for hermiticity and angular coverage. A special feature of an asymmetric B Factory is the resulting asymmetry in the momentum distributionmore » as a function of polar angle; this will also be quantified and discussed. In the next section the three primary candidates, time-of-flight (TOF), energy loss (dE/dx), and Cerenkov counters, both ring-imaging and threshold, will be briefly described and evaluated. Following this, one of the candidates, a long-drift Cerenkov ring-imaging device, is described in detail to provide a reference design. Design considerations for a fast RICH are then described. A detailed discussion of aerogel threshold counter designs and associated R D conclude the chapter. 56 refs., 64 figs., 13 tabs.« less

The irreducible photon

NASA Astrophysics Data System (ADS)

Andrews, David L.

2009-08-01

In recent years it has become evident that the primary concept of the photon has multiple interpretations, with widely differing secondary connotations. Despite the all-pervasive nature of this concept in science, some of the ancillary properties with which the photon is attributed in certain areas of application sit uneasily alongside those invoked in other areas. Certainly the range of applications extends far beyond what was envisaged in the original conception, now entering subjects extending from elementary particle physics and cosmology through to spectroscopy, statistical mechanics and photochemistry. Addressing this diverse context invites the question: What is there, that it is possible to assert as incontrovertibly true about the photon? Which properties are non-controversial, if others are the subject of debate? This paper describes an attempt to answer these questions, establishing as far as possible an irreducible core of what can rightly be asserted about the photon, and setting aside some of what often is, but should never be so asserted. Some of the more bewildering difficulties and differences of interpretation owe their origin to careless descriptions, highlighting a need to guard semantic precision; although simplifications are frequently and naturally expedient for didactic purposes, they carry the risk of becoming indelible. Focusing on such issues, the aim is to identify how much or how little about the photon can be regarded as truly non-controversial.

Nitrogen fertilizer factory effects on the amino acid and nitrogen content in the needles of Scots pine.

PubMed

Kupsinskiene, E

2001-12-04

The aim of the research was to evaluate the content of amino acids in the needles of Pinus sylvestris growing in the area affected by a nitrogen fertilizer factory and to compare them with other parameters of needles, trees, and sites. Three young-age stands of Scots pine were selected at a distance of 0.5 km, 5 km, and 17 km from the factory. Examination of the current-year needles in winter of the year 2000 revealed significant (p < 0.05) differences between the site at a 0.5-km distance from the factory and the site at a 17-km distance from the factory--with the site closest to the factory showing the highest concentrations of protein (119%), total arginine (166%), total other amino acids (depending on amino acid, the effect ranged between 119 and 149%), free arginine (771%), other free amino acids (glutamic acid, threonine, serine, lysine--depending on amino acid, the effect ranged between 162 and 234%), also the longest needles, widest diameter, largest surface area, and heaviest dry weight (respectively, 133, 110, 136, and 169%). The gradient of nitrogen concentration in the needles was assessed on the selected plots over the period of 1995-2000, with the highest concentration (depending on year, 119 to 153%) documented in the site located 0.5 km from the factory. Significant correlations were determined between the total amino acid contents (r = 0.448 -0.939, p < 0.05), some free amino acid (arginine, aspartic acid, glutamic acid, lysine, threonine, and serine) contents (r = 0.418 - 0.975, p < 0.05), and air pollutant concentration at the sites, the distance between the sites and the factory, and characteristics of the needles. No correlation was found between free or total arginine content and defoliation or retention of the needles. In conclusion, it was revealed that elevated mean monthly concentration of ammonia (26 microg m(-3)) near the nitrogen fertilizer factory caused changes in nitrogen metabolism, especially increasing (nearly eight times

Emitters of N-photon bundles

PubMed Central

Muñoz, C. Sánchez; del Valle, E.; Tudela, A. González; Müller, K.; Lichtmannecker, S.; Kaniber, M.; Tejedor, C.; Finley, J.J.; Laussy, F.P.

2014-01-01

Controlling the ouput of a light emitter is one of the basic tasks of photonics, with landmarks such as the laser and single-photon sources. The development of quantum applications makes it increasingly important to diversify the available quantum sources. Here, we propose a cavity QED scheme to realize emitters that release their energy in groups, or “bundles” of N photons, for integer N. Close to 100% of two-photon emission and 90% of three-photon emission is shown to be within reach of state of the art samples. The emission can be tuned with system parameters so that the device behaves as a laser or as a N-photon gun. The theoretical formalism to characterize such emitters is developed, with the bundle statistics arising as an extension of the fundamental correlation functions of quantum optics. These emitters will be useful for quantum information processing and for medical applications. PMID:25013456

[Heavy metals distribution characteristics and risk assessment of water below an electroplating factory].

PubMed

Hang, Xiao-Shuai; Wang, Huo-Yan; Zhou, Jian-Min

2008-10-01

Surface water and shallow groundwater within the flow of an electroplating factory was analyzed in order to study the resulting impact. The analysis method of ICP-AES was used to analyze content of zinc, manganese, chromium, copper and nickel in surface water and groundwater samples. The results indicate acidic pollutants of zinc, manganese, chromium, copper and nickel were discharged from the factory with concentrations of 1.34, 3.77, 28.1, 6.40 and 9.37 mg x L(-1), respectively; and pH was 2.32. They all exceeded permissible levels according to Integrated Wastewater Discharge Standard except zinc. Factory discharge is responsible for the longitudinal distribution characteristics of heavy metals in the stream water downstream from the factory. Heavy metals variations in the well water do not suggest they were affected by heavy metals in the stream, indicating that the migration rates of heavy metals in soils were relatively low. Risk assessment shows surface water quality significantly deteriorated. Nickel and manganese in the stream water exceeded the standard levels seriously, and chromium and copper in some samples were also above Grade III standard levels according to Environmental Quality Standard for Surface Water. Moreover, all studied heavy metals in 14 groundwater samples measured within drinking water standard, except manganese in 4 groundwater samples, which were Grade IV according to Quality Standard for Ground water.

Two-photon interference at telecom wavelengths for time-bin-encoded single photons from quantum-dot spin qubits

NASA Astrophysics Data System (ADS)

Yu, Leo; Natarajan, Chandra M.; Horikiri, Tomoyuki; Langrock, Carsten; Pelc, Jason S.; Tanner, Michael G.; Abe, Eisuke; Maier, Sebastian; Schneider, Christian; Höfling, Sven; Kamp, Martin; Hadfield, Robert H.; Fejer, Martin M.; Yamamoto, Yoshihisa

2015-11-01

Practical quantum communication between remote quantum memories rely on single photons at telecom wavelengths. Although spin-photon entanglement has been demonstrated in atomic and solid-state qubit systems, the produced single photons at short wavelengths and with polarization encoding are not suitable for long-distance communication, because they suffer from high propagation loss and depolarization in optical fibres. Establishing entanglement between remote quantum nodes would further require the photons generated from separate nodes to be indistinguishable. Here, we report the observation of correlations between a quantum-dot spin and a telecom single photon across a 2-km fibre channel based on time-bin encoding and background-free frequency downconversion. The downconverted photon at telecom wavelengths exhibits two-photon interference with another photon from an independent source, achieving a mean wavepacket overlap of greater than 0.89 despite their original wavelength mismatch (900 and 911 nm). The quantum-networking operations that we demonstrate will enable practical communication between solid-state spin qubits across long distances.

Two-photon interference at telecom wavelengths for time-bin-encoded single photons from quantum-dot spin qubits.

PubMed

Yu, Leo; Natarajan, Chandra M; Horikiri, Tomoyuki; Langrock, Carsten; Pelc, Jason S; Tanner, Michael G; Abe, Eisuke; Maier, Sebastian; Schneider, Christian; Höfling, Sven; Kamp, Martin; Hadfield, Robert H; Fejer, Martin M; Yamamoto, Yoshihisa

2015-11-24

Practical quantum communication between remote quantum memories rely on single photons at telecom wavelengths. Although spin-photon entanglement has been demonstrated in atomic and solid-state qubit systems, the produced single photons at short wavelengths and with polarization encoding are not suitable for long-distance communication, because they suffer from high propagation loss and depolarization in optical fibres. Establishing entanglement between remote quantum nodes would further require the photons generated from separate nodes to be indistinguishable. Here, we report the observation of correlations between a quantum-dot spin and a telecom single photon across a 2-km fibre channel based on time-bin encoding and background-free frequency downconversion. The downconverted photon at telecom wavelengths exhibits two-photon interference with another photon from an independent source, achieving a mean wavepacket overlap of greater than 0.89 despite their original wavelength mismatch (900 and 911 nm). The quantum-networking operations that we demonstrate will enable practical communication between solid-state spin qubits across long distances.

Two-photon interference at telecom wavelengths for time-bin-encoded single photons from quantum-dot spin qubits

PubMed Central

Yu, Leo; Natarajan, Chandra M.; Horikiri, Tomoyuki; Langrock, Carsten; Pelc, Jason S.; Tanner, Michael G.; Abe, Eisuke; Maier, Sebastian; Schneider, Christian; Höfling, Sven; Kamp, Martin; Hadfield, Robert H.; Fejer, Martin M.; Yamamoto, Yoshihisa

2015-01-01

Practical quantum communication between remote quantum memories rely on single photons at telecom wavelengths. Although spin-photon entanglement has been demonstrated in atomic and solid-state qubit systems, the produced single photons at short wavelengths and with polarization encoding are not suitable for long-distance communication, because they suffer from high propagation loss and depolarization in optical fibres. Establishing entanglement between remote quantum nodes would further require the photons generated from separate nodes to be indistinguishable. Here, we report the observation of correlations between a quantum-dot spin and a telecom single photon across a 2-km fibre channel based on time-bin encoding and background-free frequency downconversion. The downconverted photon at telecom wavelengths exhibits two-photon interference with another photon from an independent source, achieving a mean wavepacket overlap of greater than 0.89 despite their original wavelength mismatch (900 and 911 nm). The quantum-networking operations that we demonstrate will enable practical communication between solid-state spin qubits across long distances. PMID:26597223

The Operator Guide: An Ambient Persuasive Interface in the Factory

NASA Astrophysics Data System (ADS)

Meschtscherjakov, Alexander; Reitberger, Wolfgang; Pöhr, Florian; Tscheligi, Manfred

In this paper we introduce the context of a semiconductor factory as a promising area for the application of innovative interaction approaches. In order to increase efficiency ambient persuasive interfaces, which influence the operators' behaviour to perform in an optimized way, could constitute a potential strategy. We present insights gained from qualitative studies conducted in a specific semiconductor factory and provide a description of typical work processes and already deployed interfaces in this context. These findings informed the design of a prototype of an ambient persuasive interface within this realm - the "Operator Guide". Its overall aim is to improve work efficiency, while still maintaining a minimal error rate. We provide a detailed description of the Operator Guide along with an outlook of the next steps within a user-centered design approach.

Team table: a framework and tool for continuous factory planning

NASA Astrophysics Data System (ADS)

Sihn, Wilfried; Bischoff, Juergen; von Briel, Ralf; Josten, Marcus

2000-10-01

Growing market turbulences and shorter product life cycles require a continuous adaptation of factory structures resulting in a continuous factory planning process. Therefore a new framework is developed which focuses on configuration and data management process integration. This enable an online system performance evaluation based on continuous availability of current data. The use of this framework is especially helpful and will guarantee high cost and time savings, when used in the early stages of the planning, called the concept or rough planning phase. The new framework is supported by a planning round table as a tool for team-based configuration processes integrating the knowledge of all persons involved in planning processes. A case study conducted at a German company shows the advantages which can be achieved by implementing the new framework and methods.

Work-related respiratory disease in employees leaving an electronics factory.

PubMed

Perks, W H; Burge, P S; Rehahn, M; Green, M

1979-02-01

Examination of the records of employees leaving an electronics factory over three-and-a-half years showed that a significantly greater proportion left the shop floor (where soldering took place) because of ill health than left the stores and office areas. This difference was largely due to work-related respiratory disease in those whose job was soldering. Shop floor workers leaving for health reasons also had increased sickness certification due to respiratory illness compared to stores and office workers. These findings suggest that work-related respiratory illness is a significant cause of morbidity and loss of employment in solderers working at the factory and that this has been a longstanding problem with its onset before the first recorded cases of occupational asthma caused by solder flux containing colophony.

Photon-HDF5: an open file format for single-molecule fluorescence experiments using photon-counting detectors

DOE PAGES

Ingargiola, A.; Laurence, T. A.; Boutelle, R.; ...

2015-12-23

We introduce Photon-HDF5, an open and efficient file format to simplify exchange and long term accessibility of data from single-molecule fluorescence experiments based on photon-counting detectors such as single-photon avalanche diode (SPAD), photomultiplier tube (PMT) or arrays of such detectors. The format is based on HDF5, a widely used platform- and language-independent hierarchical file format for which user-friendly viewers are available. Photon-HDF5 can store raw photon data (timestamp, channel number, etc) from any acquisition hardware, but also setup and sample description, information on provenance, authorship and other metadata, and is flexible enough to include any kind of custom data. Themore » format specifications are hosted on a public website, which is open to contributions by the biophysics community. As an initial resource, the website provides code examples to read Photon-HDF5 files in several programming languages and a reference python library (phconvert), to create new Photon-HDF5 files and convert several existing file formats into Photon-HDF5. As a result, to encourage adoption by the academic and commercial communities, all software is released under the MIT open source license.« less

Homodyne versus photon-counting quantum trajectories for dissipative Kerr resonators with two-photon driving

NASA Astrophysics Data System (ADS)

Bartolo, Nicola; Minganti, Fabrizio; Lolli, Jared; Ciuti, Cristiano

2017-07-01

We investigate two different kinds of quantum trajectories for a nonlinear photon resonator subject to two-photon pumping, a configuration recently studied for the generation of photonic Schrödinger cat states. In the absence of feedback control and in the strong-driving limit, the steady-state density matrix is a statistical mixture of two states with equal weight. While along a single photon-counting trajectory the systems intermittently switches between an odd and an even cat state, we show that upon homodyne detection the situation is different. Indeed, homodyne quantum trajectories reveal switches between coherent states of opposite phase.

Itinerant Microwave Photon Detector

NASA Astrophysics Data System (ADS)

Royer, Baptiste; Grimsmo, Arne L.; Choquette-Poitevin, Alexandre; Blais, Alexandre

2018-05-01

The realization of a high-efficiency microwave single photon detector is a long-standing problem in the field of microwave quantum optics. Here, we propose a quantum nondemolition, high-efficiency photon detector that can readily be implemented in present state-of-the-art circuit quantum electrodynamics. This scheme works in a continuous fashion, gaining information about the photon arrival time as well as about its presence. The key insight that allows us to circumvent the usual limitations imposed by measurement backaction is the use of long-lived dark states in a small ensemble of inhomogeneous artificial atoms to increase the interaction time between the photon and the measurement device. Using realistic system parameters, we show that large detection fidelities are possible.

Increased lead absorption caused by working next to a lead recycling factory.

PubMed

Chao, K Y; Wang, J D

1994-08-01

The objective of this study was to determine whether workers at a factory in Taiwan, adjacent to lead recycling plant, were affected by lead contamination. Workers at the lead recycling plant itself were found to suffer from lead poisoning; air and soil outside the plant were heavily contaminated by lead. Forty-one of the 45 workers in a forging factory next to the lead recycling plant were enrolled as the exposed group. A comparison group of 51 workers were selected from another forging factory about 20 km away. Each subject was interviewed about his lifestyle, work history, and residence, and blood was drawn for lead measurement by graphite furnace atomic absorption spectrometry. The results showed that two groups were compatible in age, sex, and smoking patterns. Blood lead of the exposed group was significantly higher than that of the comparison group (mean +/- SD: 20.4 +/- 9.4 micrograms/dl vs. 5.9 +/- 2.9 micrograms/dl). The difference was independent of sex and working zones. Blood lead levels were lower among exposed workers who had been employed less than 2 months compared with those employed longer. There was no difference among exposed workers in different outdoor working zones. Five months after improvement of pollution control and decrease in the production volume of the lead factory, 30 exposed workers were retested for blood lead. The blood lead of outdoor workers had an average decrease of 4.2 micrograms/dl while that of indoor workers showed no significant difference.(ABSTRACT TRUNCATED AT 250 WORDS)

Toward precision smoking cessation treatment I: Moderator results from a factorial experiment.

PubMed

Piper, Megan E; Schlam, Tanya R; Cook, Jessica W; Smith, Stevens S; Bolt, Daniel M; Loh, Wei-Yin; Mermelstein, Robin; Collins, Linda M; Fiore, Michael C; Baker, Timothy B

2017-02-01

The development of tobacco use treatments that are effective for all smokers is critical to improving clinical and public health. The Multiphase Optimization Strategy (MOST) uses highly efficient factorial experiments to evaluate multiple intervention components for possible inclusion in an optimized tobacco use treatment. Factorial experiments permit analyses of the influence of patient characteristics on main and interaction effects of multiple, relatively discrete, intervention components. This study examined whether person-factor and smoking characteristics moderated the main or interactive effects of intervention components on 26-week self-reported abstinence rates. This fractional factorial experiment evaluated six smoking cessation intervention components among primary care patients (N=637): Prequit Nicotine Patch vs. None, Prequit Nicotine Gum vs. None, Preparation Counseling vs. None, Intensive Cessation In-Person Counseling vs. Minimal, Intensive Cessation Telephone Counseling vs. Minimal, and 16 vs. 8 Weeks of Combination Nicotine Replacement Therapy (NRT; nicotine patch+nicotine gum). Both psychiatric history and smoking heaviness moderated intervention component effects. In comparison with participants with no self-reported history of a psychiatric disorder, those with a positive history showed better response to 16- vs. 8-weeks of combination NRT, but a poorer response to counseling interventions. Also, in contrast to light smokers, heavier smokers showed a poorer response to counseling interventions. Heavy smokers and those with psychiatric histories demonstrated a differential response to intervention components. This research illustrates the use of factorial designs to examine the interactions between person characteristics and relatively discrete intervention components. Future research is needed to replicate these findings. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Quantum mechanics of a photon

NASA Astrophysics Data System (ADS)

Babaei, Hassan; Mostafazadeh, Ali

2017-08-01

A first-quantized free photon is a complex massless vector field A =(Aμ ) whose field strength satisfies Maxwell's equations in vacuum. We construct the Hilbert space H of the photon by endowing the vector space of the fields A in the temporal-Coulomb gauge with a positive-definite and relativistically invariant inner product. We give an explicit expression for this inner product, identify the Hamiltonian for the photon with the generator of time translations in H , determine the operators representing the momentum and the helicity of the photon, and introduce a chirality operator whose eigenfunctions correspond to fields having a definite sign of energy. We also construct a position operator for the photon whose components commute with each other and with the chirality and helicity operators. This allows for the construction of the localized states of the photon with a definite sign of energy and helicity. We derive an explicit formula for the latter and compute the corresponding electric and magnetic fields. These turn out to diverge not just at the point where the photon is localized but on a plane containing this point. We identify the axis normal to this plane with an associated symmetry axis and show that each choice of this axis specifies a particular position operator, a corresponding position basis, and a position representation of the quantum mechanics of a photon. In particular, we examine the position wave functions determined by such a position basis, elucidate their relationship with the Riemann-Silberstein and Landau-Peierls wave functions, and give an explicit formula for the probability density of the spatial localization of the photon.

Quantum imaging with undetected photons.

PubMed

Lemos, Gabriela Barreto; Borish, Victoria; Cole, Garrett D; Ramelow, Sven; Lapkiewicz, Radek; Zeilinger, Anton

2014-08-28

Information is central to quantum mechanics. In particular, quantum interference occurs only if there exists no information to distinguish between the superposed states. The mere possibility of obtaining information that could distinguish between overlapping states inhibits quantum interference. Here we introduce and experimentally demonstrate a quantum imaging concept based on induced coherence without induced emission. Our experiment uses two separate down-conversion nonlinear crystals (numbered NL1 and NL2), each illuminated by the same pump laser, creating one pair of photons (denoted idler and signal). If the photon pair is created in NL1, one photon (the idler) passes through the object to be imaged and is overlapped with the idler amplitude created in NL2, its source thus being undefined. Interference of the signal amplitudes coming from the two crystals then reveals the image of the object. The photons that pass through the imaged object (idler photons from NL1) are never detected, while we obtain images exclusively with the signal photons (from NL1 and NL2), which do not interact with the object. Our experiment is fundamentally different from previous quantum imaging techniques, such as interaction-free imaging or ghost imaging, because now the photons used to illuminate the object do not have to be detected at all and no coincidence detection is necessary. This enables the probe wavelength to be chosen in a range for which suitable detectors are not available. To illustrate this, we show images of objects that are either opaque or invisible to the detected photons. Our experiment is a prototype in quantum information--knowledge can be extracted by, and about, a photon that is never detected.

Development of integrated control system for smart factory in the injection molding process

NASA Astrophysics Data System (ADS)

Chung, M. J.; Kim, C. Y.

2018-03-01

In this study, we proposed integrated control system for automation of injection molding process required for construction of smart factory. The injection molding process consists of heating, tool close, injection, cooling, tool open, and take-out. Take-out robot controller, image processing module, and process data acquisition interface module are developed and assembled to integrated control system. By adoption of integrated control system, the injection molding process can be simplified and the cost for construction of smart factory can be inexpensive.

Generalized quantum interference of correlated photon pairs

PubMed Central

Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

2015-01-01

Superposition and indistinguishablility between probability amplitudes have played an essential role in observing quantum interference effects of correlated photons. The Hong-Ou-Mandel interference and interferences of the path-entangled photon number state are of special interest in the field of quantum information technologies. However, a fully generalized two-photon quantum interferometric scheme accounting for the Hong-Ou-Mandel scheme and path-entangled photon number states has not yet been proposed. Here we report the experimental demonstrations of the generalized two-photon interferometry with both the interferometric properties of the Hong-Ou-Mandel effect and the fully unfolded version of the path-entangled photon number state using photon-pair sources, which are independently generated by spontaneous parametric down-conversion. Our experimental scheme explains two-photon interference fringes revealing single- and two-photon coherence properties in a single interferometer setup. Using the proposed interferometric measurement, it is possible to directly estimate the joint spectral intensity of a photon pair source. PMID:25951143

Generalized quantum interference of correlated photon pairs.

PubMed

Kim, Heonoh; Lee, Sang Min; Moon, Han Seb

2015-05-07

Superposition and indistinguishablility between probability amplitudes have played an essential role in observing quantum interference effects of correlated photons. The Hong-Ou-Mandel interference and interferences of the path-entangled photon number state are of special interest in the field of quantum information technologies. However, a fully generalized two-photon quantum interferometric scheme accounting for the Hong-Ou-Mandel scheme and path-entangled photon number states has not yet been proposed. Here we report the experimental demonstrations of the generalized two-photon interferometry with both the interferometric properties of the Hong-Ou-Mandel effect and the fully unfolded version of the path-entangled photon number state using photon-pair sources, which are independently generated by spontaneous parametric down-conversion. Our experimental scheme explains two-photon interference fringes revealing single- and two-photon coherence properties in a single interferometer setup. Using the proposed interferometric measurement, it is possible to directly estimate the joint spectral intensity of a photon pair source.

Entanglement Concentration for Arbitrary Four-Photon Cluster State Assisted with Single Photons

NASA Astrophysics Data System (ADS)

Zhao, Sheng-Yang; Cai, Chun; Liu, Jiong; Zhou, Lan; Sheng, Yu-Bo

2016-02-01

We present an entanglement concentration protocol (ECP) to concentrate arbitrary four-photon less-entangled cluster state into maximally entangled cluster state. Different from other ECPs for cluster state, we only exploit the single photon as auxiliary, which makes this protocol feasible and economic. In our ECP, the concentrated maximally entangled state can be retained for further application and the discarded state can be reused for a higher success probability. This ECP works with the help of cross-Kerr nonlinearity and conventional photon detectors. This ECP may be useful in future one-way quantum computation.

Photon generator

DOEpatents

Srinivasan-Rao, Triveni

2002-01-01

A photon generator includes an electron gun for emitting an electron beam, a laser for emitting a laser beam, and an interaction ring wherein the laser beam repetitively collides with the electron beam for emitting a high energy photon beam therefrom in the exemplary form of x-rays. The interaction ring is a closed loop, sized and configured for circulating the electron beam with a period substantially equal to the period of the laser beam pulses for effecting repetitive collisions.

Portal Connecting Dark Photons and Axions.

PubMed

Kaneta, Kunio; Lee, Hye-Sung; Yun, Seokhoon

2017-03-10

The dark photon and the axion (or axionlike particle) are popular light particles of the hidden sector. Each of them has been actively searched for through the couplings called the vector portal and the axion portal. We introduce a new portal connecting the dark photon and the axion (axion-photon-dark photon, axion-dark photon-dark photon), which emerges in the presence of the two particles. This dark axion portal is genuinely new couplings, not just from a product of the vector portal and the axion portal, because of the internal structure of these couplings. We present a simple model that realizes the dark axion portal and discuss why it warrants a rich phenomenology.

Photon sieve telescope

NASA Astrophysics Data System (ADS)

Andersen, Geoff; Tullson, Drew

2006-06-01

In designing next-generation, ultra-large (>20m) apertures for space, many current concepts involve compactable, curved membrane reflectors. Here we present the idea of using a flat diffractive element that requires no out-of-plane deformation and so is much simpler to deploy. The primary is a photon sieve - a diffractive element consisting of a large number of precisely positioned holes distributed according to an underlying Fresnel Zone Plate (FZP) geometry. The advantage of the photon sieve over the FZP is that all the regions are connected, so the membrane substrate under simple tension can avoid buckling. Also, the hole distribution can be varied to generate any conic or apodization for specialized telescope requirements such as exo-solar planet detection. We have designed and tested numerous photon sieves as telescope primaries. Some of these have over 10 million holes in a 0.1 m diameter aperture and all of them give diffraction limited imaging. While photon sieves are diffractive elements and thus suffer from dispersion, we will present two successful solutions to this problem.

Factorial validity of the Problematic Facebook Use Scale for adolescents and young adults

PubMed Central

Marino, Claudia; Vieno, Alessio; Altoè, Gianmarco; Spada, Marcantonio M.

2017-01-01

Background and aims Recent research on problematic Facebook use has highlighted the need to develop a specific theory-driven measure to assess this potential behavioral addiction. The aim of the present study was to examine the factorial validity of the Problematic Facebook Use Scale (PFUS) adapted from Caplan’s Generalized Problematic Internet Scale model. Methods A total of 1,460 Italian adolescents and young adults (aged 14–29 years) participated in the study. Confirmatory factor analyses were performed in order to assess the factorial validity of the scale. Results Results revealed that the factor structure of the PFUS provided a good fit to the data. Furthermore, results of the multiple group analyses supported the invariance of the model across age and gender groups. Discussion and conclusions This study provides evidence supporting the factorial validity of the PFUS. This new scale provides a theory-driven tool to assess problematic use of Facebook among male and female adolescents and young adults. PMID:28198639

Factorial validity of the Problematic Facebook Use Scale for adolescents and young adults.

PubMed

Marino, Claudia; Vieno, Alessio; Altoè, Gianmarco; Spada, Marcantonio M

2017-03-01

Background and aims Recent research on problematic Facebook use has highlighted the need to develop a specific theory-driven measure to assess this potential behavioral addiction. The aim of the present study was to examine the factorial validity of the Problematic Facebook Use Scale (PFUS) adapted from Caplan's Generalized Problematic Internet Scale model. Methods A total of 1,460 Italian adolescents and young adults (aged 14-29 years) participated in the study. Confirmatory factor analyses were performed in order to assess the factorial validity of the scale. Results Results revealed that the factor structure of the PFUS provided a good fit to the data. Furthermore, results of the multiple group analyses supported the invariance of the model across age and gender groups. Discussion and conclusions This study provides evidence supporting the factorial validity of the PFUS. This new scale provides a theory-driven tool to assess problematic use of Facebook among male and female adolescents and young adults.

Photon-photon scattering at the high-intensity frontier

NASA Astrophysics Data System (ADS)

Gies, Holger; Karbstein, Felix; Kohlfürst, Christian; Seegert, Nico

2018-04-01

The tremendous progress in high-intensity laser technology and the establishment of dedicated high-field laboratories in recent years have paved the way towards a first observation of quantum vacuum nonlinearities at the high-intensity frontier. We advocate a particularly prospective scenario, where three synchronized high-intensity laser pulses are brought into collision, giving rise to signal photons, whose frequency and propagation direction differ from the driving laser pulses, thus providing various means to achieve an excellent signal to background separation. Based on the theoretical concept of vacuum emission, we employ an efficient numerical algorithm which allows us to model the collision of focused high-intensity laser pulses in unprecedented detail. We provide accurate predictions for the numbers of signal photons accessible in experiment. Our study is the first to predict the precise angular spread of the signal photons, and paves the way for a first verification of quantum vacuum nonlinearity in a well-controlled laboratory experiment at one of the many high-intensity laser facilities currently coming online.

Entangled-photon compressive ghost imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zerom, Petros; Chan, Kam Wai Clifford; Howell, John C.

2011-12-15

We have experimentally demonstrated high-resolution compressive ghost imaging at the single-photon level using entangled photons produced by a spontaneous parametric down-conversion source and using single-pixel detectors. For a given mean-squared error, the number of photons needed to reconstruct a two-dimensional image is found to be much smaller than that in quantum ghost imaging experiments employing a raster scan. This procedure not only shortens the data acquisition time, but also suggests a more economical use of photons for low-light-level and quantum image formation.

Promoting contraceptive use among unmarried female migrants in one factory in Shanghai: a pilot workplace intervention.

PubMed

Qian, Xu; Smith, Helen; Huang, Wenyuan; Zhang, Jie; Huang, Ying; Garner, Paul

2007-05-31

In urban China, more single women are becoming pregnant and resorting to induced abortion, despite the wide availability of temporary methods of contraception. We developed and piloted a workplace-based intervention to promote contraceptive use in unmarried female migrants working in privately owned factories. Quasi-experimental design. In consultation with clients, we developed a workplace based intervention to promote contraception use in unmarried female migrants in a privately owned factory. We then implemented this in one factory, using a controlled before-and-after design. The intervention included lectures, bespoke information leaflets, and support to the factory doctors in providing a contraceptive service. 598 women participated: most were under 25, migrants to the city, with high school education. Twenty percent were lost when staff were made redundant, and implementation was logistically complicated. All women attended the initial lecture, and just over half the second lecture. Most reported reading the educational material provided (73%), but very few women reported using the free family planning services offered at the factory clinic (5%) or the Family Planning Institute (3%). At baseline, 90% (N = 539) stated that contraceptives were required if having sex before marriage; of those reporting sex in the last three months, the majority reporting using contraceptives (78%, 62/79) but condom use was low (44%, 35/79). Qualitative data showed that the reading material seemed to be popular and young women expressed a need for more specific reproductive health information, particularly on HIV/AIDS. Women wanted services with some privacy and anonymity, and views on the factory service were mixed. Implementing a complex intervention with a hard to reach population through a factory in China, using a quasi-experimental design, is not easy. Further research should focus on the specific needs and service preferences of this population and these should be

The eldercare factory.

PubMed

Sharkey, Noel; Sharkey, Amanda

2012-01-01

Rapid advances in service robotics together with dramatic shifts in population demographics have led to the notion that technology may be the answer to our eldercare problems. Robots are being developed for feeding, washing, lifting, carrying and mobilising the elderly as well as monitoring their health. They are also being proposed as a substitute for companionship. While these technologies could accrue major benefits for society and empower the elderly, we must balance their use with the ethical costs. These include a potential reduction in human contact, increased feeling of objectification and loss of control, loss of privacy and personal freedom as well as deception and infantilisation. With appropriate guidelines in place before the introduction of robots en masse into the care system, robots could improve the lives of the elderly, reducing their dependence and creating more opportunities for social interaction. Without forethought, the elderly may find themselves in a barren world of machines, a world of automated care: a factory for the elderly. Copyright © 2011 S. Karger AG, Basel.

Single-photon and two-photon excited fluorescence behavior of a novel fluorene-based compound

NASA Astrophysics Data System (ADS)

Ma, Wenbo; Wu, Yiquan; Gu, Donghong; Gan, Fuxi

2005-09-01

A D-π-D type compound, 2,7-bis(4-methoxystyryl)-9,9-bis(2-ethylhexyl)-9H-fluorene (abbreviated as MO-Flu-MO), where electron-donor D is methoxy group andπis fluorene unit, has been synthesized. The molecular structures of the compound were characterized by elemental analyses, EI-MS and FT-IR spectra. UV-Vis spectra in the region 230--1000 nm and single-photon excited fluorescence in tetrahydrofuran (THF) of the compound were measured. It is found that the new compound exhibits strong two-photon excited fluorescence in the region 380--500 nm and moderate two-photon absorption (TPA) value in the femtoseconds regime (TPA cross-section as high as 55×10-50 cm4 s photon-1 with 13fs laser pulses). The results demonstrate that the compound is a promising candidate for two-photon three-dimensional (3D) optical data storage.

Photon Entanglement Through Brain Tissue

PubMed Central

Shi, Lingyan; Galvez, Enrique J.; Alfano, Robert R.

2016-01-01

Photon entanglement, the cornerstone of quantum correlations, provides a level of coherence that is not present in classical correlations. Harnessing it by study of its passage through organic matter may offer new possibilities for medical diagnosis technique. In this work, we study the preservation of photon entanglement in polarization, created by spontaneous parametric down-conversion, after one entangled photon propagates through multiphoton-scattering brain tissue slices with different thickness. The Tangle-Entropy (TS) plots show the strong preservation of entanglement of photons propagating in brain tissue. By spatially filtering the ballistic scattering of an entangled photon, we find that its polarization entanglement is preserved and non-locally correlated with its twin in the TS plots. The degree of entanglement correlates better with structure and water content than with sample thickness. PMID:27995952

Photon Entanglement Through Brain Tissue.

PubMed

Shi, Lingyan; Galvez, Enrique J; Alfano, Robert R

2016-12-20

Photon entanglement, the cornerstone of quantum correlations, provides a level of coherence that is not present in classical correlations. Harnessing it by study of its passage through organic matter may offer new possibilities for medical diagnosis technique. In this work, we study the preservation of photon entanglement in polarization, created by spontaneous parametric down-conversion, after one entangled photon propagates through multiphoton-scattering brain tissue slices with different thickness. The Tangle-Entropy (TS) plots show the strong preservation of entanglement of photons propagating in brain tissue. By spatially filtering the ballistic scattering of an entangled photon, we find that its polarization entanglement is preserved and non-locally correlated with its twin in the TS plots. The degree of entanglement correlates better with structure and water content than with sample thickness.

Photon Entanglement Through Brain Tissue

NASA Astrophysics Data System (ADS)

Shi, Lingyan; Galvez, Enrique J.; Alfano, Robert R.

2016-12-01

Photon entanglement, the cornerstone of quantum correlations, provides a level of coherence that is not present in classical correlations. Harnessing it by study of its passage through organic matter may offer new possibilities for medical diagnosis technique. In this work, we study the preservation of photon entanglement in polarization, created by spontaneous parametric down-conversion, after one entangled photon propagates through multiphoton-scattering brain tissue slices with different thickness. The Tangle-Entropy (TS) plots show the strong preservation of entanglement of photons propagating in brain tissue. By spatially filtering the ballistic scattering of an entangled photon, we find that its polarization entanglement is preserved and non-locally correlated with its twin in the TS plots. The degree of entanglement correlates better with structure and water content than with sample thickness.

Photonic crystal sensors: Physics and applications

NASA Astrophysics Data System (ADS)

Dinodiya, Sapna; Suthar, B.; Bhargava, A.

2018-05-01

Photonic sensors have evolved rapidly in last few decades because of the major requirement of sensing applications in optical communication and biomedical diagnostics. Photonic crystals are of tremendous use in designing photonic sensors. Any physical phenomenon, for instance temperature, pressure, strain, and presence of chemicals and bio molecules that can alter periodicity and refractive index of structure of the photonic crystal, can be sensed by measuring optical properties like spectral pattern of reflected and transmitted power. The physics and applications of various photonic crystal sensors are presented in this article.

Comparison of Grouping Schemes for Exposure to Total Dust in Cement Factories in Korea.

PubMed

Koh, Dong-Hee; Kim, Tae-Woo; Jang, Seung Hee; Ryu, Hyang-Woo; Park, Donguk

2015-08-01

The purpose of this study was to evaluate grouping schemes for exposure to total dust in cement industry workers using non-repeated measurement data. In total, 2370 total dust measurements taken from nine Portland cement factories in 1995-2009 were analyzed. Various grouping schemes were generated based on work process, job, factory, or average exposure. To characterize variance components of each grouping scheme, we developed mixed-effects models with a B-spline time trend incorporated as fixed effects and a grouping variable incorporated as a random effect. Using the estimated variance components, elasticity was calculated. To compare the prediction performances of different grouping schemes, 10-fold cross-validation tests were conducted, and root mean squared errors and pooled correlation coefficients were calculated for each grouping scheme. The five exposure groups created a posteriori by ranking job and factory combinations according to average dust exposure showed the best prediction performance and highest elasticity among various grouping schemes. Our findings suggest a grouping method based on ranking of job, and factory combinations would be the optimal choice in this population. Our grouping method may aid exposure assessment efforts in similar occupational settings, minimizing the misclassification of exposures. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Photonics for life.

PubMed

Cubeddu, Rinaldo; Bassi, Andrea; Comelli, Daniela; Cova, Sergio; Farina, Andrea; Ghioni, Massimo; Rech, Ivan; Pifferi, Antonio; Spinelli, Lorenzo; Taroni, Paola; Torricelli, Alessandro; Tosi, Alberto; Valentini, Gianluca; Zappa, Franco

2011-01-01

Light is strictly connected with life, and its presence is fundamental for any living environment. Thus, many biological mechanisms are related to light interaction or can be evaluated through processes involving energy exchange with photons. Optics has always been a precious tool to evaluate molecular and cellular mechanisms, but the discovery of lasers opened new pathways of interactions of light with biological matter, pushing an impressive development for both therapeutic and diagnostic applications in biomedicine. The use of light in different fields has become so widespread that the word photonics has been utilized to identify all the applications related to processes where the light is involved. The photonics area covers a wide range of wavelengths spanning from soft X-rays to mid-infrared and includes all devices related to photons as light sources, optical fibers and light guides, detectors, and all the related electronic equipment. The recent use of photons in the field of telecommunications has pushed the technology toward low-cost, compact, and efficient devices, making them available for many other applications, including those related to biology and medicine where these requirements are of particular relevance. Moreover, basic sciences such as physics, chemistry, mathematics, and electronics have recognized the interdisciplinary need of biomedical science and are translating the most advanced researches into these fields. The Politecnico school has pioneered many of them,and this article reviews the state of the art of biomedical research at the Politecnico in the field internationally known as biophotonics.

Photonic band gap properties of one-dimensional Thue-Morse all-dielectric photonic quasicrystal

NASA Astrophysics Data System (ADS)

Yue, Chenxi; Tan, Wei; Liu, Jianjun

2018-05-01

In this paper, the photonic band gap (PBG) properties of one-dimensional (1D) Thue-Morse photonic quasicrystal (PQC) S4 structure are theoretically investigated by using transfer matrix method in Bragg condition. The effects of the center wavelength, relative permittivity and incident angle on PBG properties are elaborately analyzed. Numerical results reveal that, in the case of normal incidence, the symmetry and periodicity properties of the photonic band structure are presented. As the center wavelength increases, the PBG center frequency and PBG width decrease while the photonic band structure is always symmetrical about the central frequency and the photonic band structure repeats periodically in the expanding observation frequency range. With the decrease of relative permittivity contrast, the PBG width and the relative PBG width gradually decreases until PBG disappears while the symmetry of the photonic band structure always exists. In the case of oblique incidence, as the incident angle increases, multiple narrow PBGs gradually merge into a wide PBG for the TE mode while for the TM mode, the number of PBG continuously decreases and eventually disappears, i.e., multiple narrow PBGs become a wide passband for the TM mode. The research results will provide a reference for the choice of the material, the incident angle for the PBG properties and its applications of 1D Thue-Morse PQC.

Accuracy of quantum sensors measuring yield photon flux and photosynthetic photon flux

NASA Technical Reports Server (NTRS)

Barnes, C.; Tibbitts, T.; Sager, J.; Deitzer, G.; Bubenheim, D.; Koerner, G.; Bugbee, B.; Knott, W. M. (Principal Investigator)

1993-01-01

Photosynthesis is fundamentally driven by photon flux rather than energy flux, but not all absorbed photons yield equal amounts of photosynthesis. Thus, two measures of photosynthetically active radiation have emerged: photosynthetic photon flux (PPF), which values all photons from 400 to 700 nm equally, and yield photon flux (YPF), which weights photons in the range from 360 to 760 nm according to plant photosynthetic response. We selected seven common radiation sources and measured YPF and PPF from each source with a spectroradiometer. We then compared these measurements with measurements from three quantum sensors designed to measure YPF, and from six quantum sensors designed to measure PPF. There were few differences among sensors within a group (usually <5%), but YPF values from sensors were consistently lower (3% to 20%) than YPF values calculated from spectroradiometric measurements. Quantum sensor measurements of PPF also were consistently lower than PPF values calculated from spectroradiometric measurements, but the differences were <7% for all sources, except red-light-emitting diodes. The sensors were most accurate for broad-band sources and least accurate for narrow-band sources. According to spectroradiometric measurements, YPF sensors were significantly less accurate (>9% difference) than PPF sensors under metal halide, high-pressure sodium, and low-pressure sodium lamps. Both sensor types were inaccurate (>18% error) under red-light-emitting diodes. Because both YPF and PPF sensors are imperfect integrators, and because spectroradiometers can measure photosynthetically active radiation much more accurately, researchers should consider developing calibration factors from spectroradiometric data for some specific radiation sources to improve the accuracy of integrating sensors.

Gamma ray pulsars. [electron-photon cascades

NASA Technical Reports Server (NTRS)

Oegelman, H.; Ayasli, S.; Hacinliyan, A.

1977-01-01

Data from the SAS-2 high-energy gamma-ray experiment reveal the existence of four pulsars emitting photons above 35 MeV. An attempt is made to explain the gamma-ray emission from these pulsars in terms of an electron-photon cascade that develops in the magnetosphere of the pulsar. Although there is very little material above the surface of the pulsar, the very intense magnetic fields (10 to the 12th power gauss) correspond to many radiation lengths which cause electrons to emit photons by magnetic bremsstrahlung and which cause these photons to pair-produce. The cascade develops until the mean photon energy drops below the pair-production threshold which is in the gamma-ray range; at this stage, the photons break out from the source.

Single-Photon-Triggered Quantum Phase Transition

NASA Astrophysics Data System (ADS)

Lü, Xin-You; Zheng, Li-Li; Zhu, Gui-Lei; Wu, Ying

2018-06-01

We propose a hybrid quantum model combining cavity QED and optomechanics, which allows the occurrence of an equilibrium superradiant quantum phase transition (QPT) triggered by a single photon. This single-photon-triggered QPT exists in the cases of both ignoring and including the so-called A2 term; i.e., it is immune to the no-go theorem. It originally comes from the photon-dependent quantum criticality featured by the proposed hybrid quantum model. Moreover, a reversed superradiant QPT is induced by the competition between the introduced A2 term and the optomechanical interaction. This work offers an approach to manipulate QPT with a single photon, which should inspire the exploration of single-photon quantum-criticality physics and the engineering of new single-photon quantum devices.

Quantum optics. All-optical routing of single photons by a one-atom switch controlled by a single photon.

PubMed

Shomroni, Itay; Rosenblum, Serge; Lovsky, Yulia; Bechler, Orel; Guendelman, Gabriel; Dayan, Barak

2014-08-22

The prospect of quantum networks, in which quantum information is carried by single photons in photonic circuits, has long been the driving force behind the effort to achieve all-optical routing of single photons. We realized a single-photon-activated switch capable of routing a photon from any of its two inputs to any of its two outputs. Our device is based on a single atom coupled to a fiber-coupled, chip-based microresonator. A single reflected control photon toggles the switch from high reflection (R ~ 65%) to high transmission (T ~ 90%), with an average of ~1.5 control photons per switching event (~3, including linear losses). No additional control fields are required. The control and target photons are both in-fiber and practically identical, making this scheme compatible with scalable architectures for quantum information processing. Copyright © 2014, American Association for the Advancement of Science.

SWITCH: a dynamic CRISPR tool for genome engineering and metabolic pathway control for cell factory construction in Saccharomyces cerevisiae.

PubMed

Vanegas, Katherina García; Lehka, Beata Joanna; Mortensen, Uffe Hasbro

2017-02-08

The yeast Saccharomyces cerevisiae is increasingly used as a cell factory. However, cell factory construction time is a major obstacle towards using yeast for bio-production. Hence, tools to speed up cell factory construction are desirable. In this study, we have developed a new Cas9/dCas9 based system, SWITCH, which allows Saccharomyces cerevisiae strains to iteratively alternate between a genetic engineering state and a pathway control state. Since Cas9 induced recombination events are crucial for SWITCH efficiency, we first developed a technique TAPE, which we have successfully used to address protospacer efficiency. As proof of concept of the use of SWITCH in cell factory construction, we have exploited the genetic engineering state of a SWITCH strain to insert the five genes necessary for naringenin production. Next, the naringenin cell factory was switched to the pathway control state where production was optimized by downregulating an essential gene TSC13, hence, reducing formation of a byproduct. We have successfully integrated two CRISPR tools, one for genetic engineering and one for pathway control, into one system and successfully used it for cell factory construction.

Photonic crystal ring resonator based optical filters for photonic integrated circuits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robinson, S., E-mail: mail2robinson@gmail.com

In this paper, a two Dimensional (2D) Photonic Crystal Ring Resonator (PCRR) based optical Filters namely Add Drop Filter, Bandpass Filter, and Bandstop Filter are designed for Photonic Integrated Circuits (PICs). The normalized output response of the filters is obtained using 2D Finite Difference Time Domain (FDTD) method and the band diagram of periodic and non-periodic structure is attained by Plane Wave Expansion (PWE) method. The size of the device is minimized from a scale of few tens of millimeters to the order of micrometers. The overall size of the filters is around 11.4 μm × 11.4 μm which ismore » highly suitable of photonic integrated circuits.« less

Breakdown of Bose-Einstein distribution in photonic crystals.

PubMed

Lo, Ping-Yuan; Xiong, Heng-Na; Zhang, Wei-Min

2015-03-30

In the last two decades, considerable advances have been made in the investigation of nano-photonics in photonic crystals. Previous theoretical investigations of photon dynamics were carried out at zero temperature. Here, we investigate micro/nano cavity photonics in photonic crystals at finite temperature. Due to photonic-band-gap-induced localized long-lived photon dynamics, we discover that cavity photons in photonic crystals do not obey Bose-Einstein statistical distribution. Within the photonic band gap and in the vicinity of the band edge, cavity photons combine the long-lived non-Markovain dynamics with thermal fluctuations together to form photon states that memorize the initial cavity state information. As a result, Bose-Einstein distribution is completely broken down in these regimes, even if the thermal energy is larger or much larger than the cavity detuning energy. In this investigation, a crossover phenomenon from equilibrium to nonequilibrium steady states is also revealed.

Two-photon geometrical phase

NASA Astrophysics Data System (ADS)

Strekalov, D. V.; Shih, Y. H.

1997-10-01

An advanced wave model is applied to a two-photon interference experiment to show that the observed interference effect is due to the geometrical phase of a two-photon state produced in spontaneous parametric down-conversion. The polarization state of the signal-idler pair is changed adiabatically so that the ``loop'' on the Poincaré sphere is opened in the signal channel and closed in the idler channel. Therefore, we observed an essentially nonlocal geometrical phase, shared by the entangled photon pair, or a biphoton.

Symptoms of musculoskeletal disorders among ammunition factory workers in Turkey.

PubMed

Pinar, Tevfik; Cakmak, Z Aytul; Saygun, Meral; Akdur, Recep; Ulu, Nuriye; Keles, Isik; Saylam, Hamdi Saim

2013-01-01

The aim of this study was to assess the prevalence of symptoms of work-related musculoskeletal disorders (MSDs) and to determine the risk factors among ammunition factory workers in Turkey. This cross-sectional study was performed on 955 ammunition factory workers. Potential risk factors were investigated with a questionnaire and multivariate logistic regression analysis was performed. During the previous year, 39.3% of ammunition workers experienced symptoms of work-related MSDs. Logistic regression analysis showed smoking (odds ratio [OR] = 1.372), chronic diseases (OR = 1.795), body mass index (BMI; overweight) (OR = 1.631), working year (OR = 1.509), cold temperature (OR = 1.838), and work load (OR = 2.210) were significant independent risk factors for the development of symptoms of MSDs. It was found that both work-related conditions and personal and environmental factors are important for the development of occupational MSDs.

PHOTON2: A web-based professional development model for photonics technology education

NASA Astrophysics Data System (ADS)

Massa, Nicholas M.; Washburn, Barbara A.; Kehrhahn, Marijke; Donnelly, Judith F.; Hanes, Fenna D.

2004-10-01

In this paper, we present a web-based teacher professional development model for photonics technology education funded by the National Science Foundation Advanced Technology Education (ATE) program. In response to the rapidly growing demand for skilled photonics technicians, the PHOTON2 project will increase the number of high school teachers and community college faculty across the US proficient in teaching photonics technology at their own institutions. The project will also focus on building the capacity of educators to engage in lifelong learning through web-based professional development. Unlike the traditional professional development model whereby educators receive training through intensive short-term workshops, the PHOTON2 project team has developed a pedagogical framework designed specifically for adult learners in which technical content, curriculum development, and learner self-regulatory development are integrated into an active, collaborative, and sustained online learning environment. In Spring 2004, two cohorts of science and technology educators, career/guidance counselors, and industry mentors from eleven states including California, Pennsylvania, Texas, Arizona, Hawaii, and the six New England states commenced participation in the three-year project. Qualitative and quantitative research, focused on individual and environmental factors related to web-based learning, will examine the viability of web-based teacher/faculty professional development in engineering technology education.

Factorial Validity and Invariance Testing of the Exercise Dependence Scale-Revised in Swedish and Portuguese Exercisers

ERIC Educational Resources Information Center

Lindwall, Magnus; Palmeira, Antonio

2009-01-01

The present study investigated the factorial validity and factorial invariance of the 21-item Exercise Dependence Scale-Revised using 162 Swedish and 269 Portuguese exercisers. In addition, the prevalence of exercise dependence symptoms and links to exercise behavior, gender, and age in the two samples was also studied. Confirmatory factor…

Background-Source Cosmic-Photon Elevation Scaling and Cosmic-Neutron/Photon Date Scaling in MCNP6

NASA Astrophysics Data System (ADS)

Tutt, J.; Anderson, C.; McKinney, G.

Cosmic neutron and photon fluxes are known to scale exponentially with elevation. Consequently, cosmic neutron elevation scaling was implemented for use with the background-source option shortly after its introduction into MCNP6, whereby the neutron flux weight factor was adjusted by the elevation scaling factor when the user-specified elevation differed from the selected background.dat grid-point elevation. At the same time, an elevation scaling factor was suggested for the cosmic photon flux, however, cosmic photon elevation scaling is complicated by the fact that the photon background consists of two components: cosmic and terrestrial. Previous versions of the background.dat file did not provide any way to separate these components. With Rel. 4 of this file in 2015, two new columns were added that provide the energy grid and differential cosmic photon flux separately from the total photon flux. Here we show that the cosmic photon flux component can now be scaled independently and combined with the terrestrial component to form the total photon flux at a user-specified elevation in MCNP6. Cosmic background fluxes also scale with the solar cycle due to solar modulation. This modulation has been shown to be nearly sinusoidal over time, with an inverse effect - increased modulation leads to a decrease in cosmic fluxes. This effect was initially included with the cosmic source option in MCNP6 and has now been extended for use with the background source option when: (1) the date is specified in the background.dat file, and (2) when the user specifies a date on the source definition card. A description of the cosmic-neutron/photon date scaling feature will be presented along with scaling results for past and future date extrapolations.

Structural analysis of polymer thin films using GISAXS in the tender X-ray region: Concept and design of GISAXS experiments using the tender X-ray energy at BL-15A2 at the Photon Factory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takagi, H., E-mail: takagih@post.kek.jp; Igarashi, N.; Mori, T.

If small angle X-ray scattering (SAXS) utilizing the soft X-ray region is available, advanced and unique experiments, which differ from traditional SAXS methods, can be realized. For example, grazing-incidence small angle X-ray scattering (GISAXS) using hard X-ray is a powerful tool for understanding the nanostructure in both vertical and lateral directions of thin films, while GISAXS utilizing the tender X-ray region (SX-GISAXS) enables depth-resolved analysis as well as a standard GISAXS analysis in thin films. Thus, at BL-15A2 at the Photon Factory, a dedicated diffractometer for SX-GISAXS (above 2.1 keV) was constructed. This diffractometer is composed of four vacuum chambers andmore » can be converted into the vacuum state from the sample chamber in front of the detector surface. Diffractions are clearly observed until 12th peak when measuring collagen by SAXS with an X-ray energy of 2.40 keV and a camera length of 825 mm. Additionally, we conducted the model experiment using SX-GISAXS with an X-ray energy of 2.40 keV to confirm that a poly(methyl methacrylate)-poly(n-butyl acrylate) block copolymer thin film has a microphase-separated structure in the thin film, which is composed of lamellae aligned both parallel and perpendicular to the substrate surface. Similarly, in a polystyrene-poly(methyl methacrylate) block copolymer thin film, SX-GISAXS with 3.60 keV and 5.73 keV revealed that hexagonally packed cylinders are aligned parallel to the substrate surface. The incident angle dependence of the first order peak position of the q{sub z} direction obtained from experiments at various incident X-ray energies agrees very well with the theoretical one calculated from the distorted wave Born approximation.« less

Occupational hazards and safety measures amongst the paint factory workers in lagos, Nigeria.

PubMed

Awodele, Olufunsho; Popoola, Temidayo D; Ogbudu, Bawo S; Akinyede, Akin; Coker, Herbert A B; Akintonwa, Alade

2014-06-01

The manufacture of paint involves a variety of processes that present with medical hazards. Safety initiatives are hence introduced to limit hazard exposures and promote workplace safety. This aim of this study is to assess the use of available control measures/initiatives in selected paint factories in Lagos West Senatorial District, Nigeria. A total of 400 randomly selected paint factory workers were involved in the study. A well-structured World Health Organization standard questionnaire was designed and distributed to the workers to elicit information on awareness to occupational hazards, use of personal protective devices, and commonly experienced adverse symptoms. Urine samples were obtained from 50 workers randomly selected from these 400 participants, and the concentrations of the heavy metals (lead, cadmium, arsenic, and chromium) were determined using atomic absorption spectroscopy. The results show that 72.5% of the respondents are aware of the hazards associated with their jobs; 30% have had formal training on hazards and safety measures; 40% do not use personal protective devices, and 90% of the respondents reported symptoms relating to hazard exposure. There was a statistically significant (p < 0.05) increase in the mean heavy metal concentrations in the urine samples obtained from paint factory workers as compared with nonfactory workers. The need to develop effective frameworks that will initiate the integration and ensure implementation of safety regulations in paint factories is evident. Where these exist, there is a need to promote adherence to these practice guidelines.

Measurement of Employability Skills on Teaching Factory Learning

NASA Astrophysics Data System (ADS)

Subekti, S.; Ana, A.

2018-02-01

Vocational High Schools as one of the educational institutions that has the responsibility in preparing skilled labors has a challenge to improve the quality of human resources as a candidate for skilled labors, to compete and survive in a changing climate of work. BPS noted an increase in the number of non-worker population (BAK) in 2015-2017 on vocational graduates as many as 564,272 people. The ability to adapt and maintain jobs in a variety of conditions is called employability skills. This study purpose to measure the development of employability skills of communication skills, problem-solving skills and teamwork skills on the implementation of teaching factory learning in SMK Negeri 1 Cibadak, THPH Skills Program on bakery competency. This research uses mixed method, with concurrent triangulation mix methods research design. Data collection techniques used interviews and questionnaires. The result shows that there are increasing students’ employability skills in communication skills, problem solving skills, and teamwork skills in teaching factory learning. Principles of learning that apply learning by doing student centering and learning arrangements such as situations and conditions in the workplace have an impact on improving student employability skills.

1. VIEW LOOKING SOUTHWEST AT PARTIAL EAST ELEVATION OF FACTORY, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. VIEW LOOKING SOUTHWEST AT PARTIAL EAST ELEVATION OF FACTORY, SHOWING FORMER OHIO & ERIE CANAL PRISM IN FOREGROUND THAT WAS USED AS WATER RESERVOIR (500,000 GALLON) - Jaite Paper Mill, 1200 West Highland Road, Sagamore Hills, Summit County, OH

Exceptional enhancement of Raman scattering on silver chlorobromide nanocube photonic crystals: chemical and photonic contributions

DOE PAGES

Li, Zheng; Gosztola, David J.; Sun, Cheng-Jun; ...

2015-02-02

Photonic crystals made from self-assembly of mono-dispersed AgCl xBr 1-x nanocubes, which are not plasmonically active, have been discovered to exceptionally enhance Raman scattering of molecules chemically adsorbed on their surfaces. Comprehensive control measurements and X-ray absorption near-edge structure spectroscopy indicate that the Raman enhancement on the AgCl xBr 1-x nanocube photonic crystals is primarily ascribed to the chemical enhancement mechanism associated with the chemical interactions between adsorbing molecules and the AgCl xBr 1-x surfaces. In addition, the ordering of the AgCl xBr 1-x nanocubes in the photonic crystals can selectively reflect Raman scattering back to the detector at themore » bandgap position of the photonic crystals to provide additional enhancement, i.e., photonic mode enhancement. The thiophenol molecules adsorbed on the AgCl 0.44Br 0.56 nanocube photonic crystals exhibit astonishingly strong Raman signals that are on the same order of magnitude as those recorded from the thiophenol molecules adsorbed on the assembled Ag nanocubes.« less

Dressed photons from the viewpoint of photon localization: the entrance to the off-shell science

NASA Astrophysics Data System (ADS)

Saigo, Hayato; Ojima, Izumi; Ohtsu, Motoichi

2017-12-01

In the present paper, a new aspect of the interplay is examined between mathematical-physical arguments and light-matter fusion technologies in terms of the concept of "effective mass", starting from a question: Who has seen a free photon? Owing to the general results due to Newton-Wigner and to Wightman, a position operator is absent for massless free particles with non-zero finite spins, and hence, we cannot observe free photons in any local space regions. To solve this paradox of "photon localization", the effective mass of a photon needs to be generated through the couplings of photons with matter. Here "polaritons" picture as a basic notion in optical and solid physics is shown to verify this viewpoint, which is seen to apply also to more general settings . Focusing on the role played by nanoparticles, we reach a new look at the notion of "dressed photons" as off-shell particles. The perspective above shows that essential mathematical structure of quantum field theory for the so-called elementary particles in subatomic scale can also be applied to certain phenomena in the nano-scale.

An Innovation in Children's T.V. the Infinity Factory

ERIC Educational Resources Information Center

La Luz, 1977

1977-01-01

"Infinity Factory" is a slick, fast-paced, sophisticated series aimed at teaching mathematics fundamentals with a unique and arresting approach. The 30 minutes of live-action skits, brief filmed documentaries, and animation sequences explore common sense math concepts and present useful information showing math at work in everyday life. (NQ)

Factorial study of rain garden design for nitrogen removal

EPA Science Inventory

Abstract Nitrate (〖NO〗_3^--N ) removal studies in bioretention systems showed great variability in removal rates and in some cases 〖NO〗_3^--N was exported. A 3-way factorial design (2 x 2 x 4) was devised for eight outdoor un-vegetated rain gardens to evaluate the effects of ...

Breakdown of Bose-Einstein Distribution in Photonic Crystals

PubMed Central

Lo, Ping-Yuan; Xiong, Heng-Na; Zhang, Wei-Min

2015-01-01

In the last two decades, considerable advances have been made in the investigation of nano-photonics in photonic crystals. Previous theoretical investigations of photon dynamics were carried out at zero temperature. Here, we investigate micro/nano cavity photonics in photonic crystals at finite temperature. Due to photonic-band-gap-induced localized long-lived photon dynamics, we discover that cavity photons in photonic crystals do not obey Bose-Einstein statistical distribution. Within the photonic band gap and in the vicinity of the band edge, cavity photons combine the long-lived non-Markovain dynamics with thermal fluctuations together to form photon states that memorize the initial cavity state information. As a result, Bose-Einstein distribution is completely broken down in these regimes, even if the thermal energy is larger or much larger than the cavity detuning energy. In this investigation, a crossover phenomenon from equilibrium to nonequilibrium steady states is also revealed. PMID:25822135

Antigravity Acts on Photons

NASA Astrophysics Data System (ADS)

Brynjolfsson, Ari

2002-04-01

Einstein's general theory of relativity assumes that photons don't change frequency as they move from Sun to Earth. This assumption is correct in classical physics. All experiments proving the general relativity are in the domain of classical physics. This include the tests by Pound et al. of the gravitational redshift of 14.4 keV photons; the rocket experiments by Vessot et al.; the Galileo solar redshift experiments by Krisher et al.; the gravitational deflection of light experiments by Riveros and Vucetich; and delay of echoes of radar signals passing close to Sun as observed by Shapiro et al. Bohr's correspondence principle assures that quantum mechanical theory of general relativity agrees with Einstein's classical theory when frequency and gravitational field gradient approach zero, or when photons cannot interact with the gravitational field. When we treat photons as quantum mechanical particles; we find that gravitational force on photons is reversed (antigravity). This modified theory contradicts the equivalence principle, but is consistent with all experiments. Solar lines and distant stars are redshifted in accordance with author's plasma redshift theory. These changes result in a beautiful consistent cosmology.

Experimental Ten-Photon Entanglement.

PubMed

Wang, Xi-Lin; Chen, Luo-Kan; Li, W; Huang, H-L; Liu, C; Chen, C; Luo, Y-H; Su, Z-E; Wu, D; Li, Z-D; Lu, H; Hu, Y; Jiang, X; Peng, C-Z; Li, L; Liu, N-L; Chen, Yu-Ao; Lu, Chao-Yang; Pan, Jian-Wei

2016-11-18

We report the first experimental demonstration of quantum entanglement among ten spatially separated single photons. A near-optimal entangled photon-pair source was developed with simultaneously a source brightness of ∼12  MHz/W, a collection efficiency of ∼70%, and an indistinguishability of ∼91% between independent photons, which was used for a step-by-step engineering of multiphoton entanglement. Under a pump power of 0.57 W, the ten-photon count rate was increased by about 2 orders of magnitude compared to previous experiments, while maintaining a state fidelity sufficiently high for proving the genuine ten-particle entanglement. Our work created a state-of-the-art platform for multiphoton experiments, and enabled technologies for challenging optical quantum information tasks, such as the realization of Shor's error correction code and high-efficiency scattershot boson sampling.

Insulin-like growth factor-I, physical activity, and control of cellular anabolism.

PubMed

Nindl, Bradley C

2010-01-01

The underlying mechanisms responsible for mediating the beneficial outcomes of exercise undoubtedly are many, but the insulin-like growth factor-I (IGF-I) system is emerging as an important and central hormonal axis that plays a significant role concerning cellular anabolism. This introductory article summarizes the intent and the content for papers presented as part of a 2008 American College of Sports Medicine national symposium entitled "Insulin-like Growth Factor-I, Physical Activity, and Control of Cellular Anabolism." The individual authors and their papers are as follows: Jan Frystyk authoring "The relationship between exercise and the growth hormone/insulin-like growth factor-I axis," Greg Adams authoring "IGF-I signaling in skeletal muscle and the potential for cytokine interactions," and Brad Nindl authoring "Insulin-like growth factor-I as a biomarker of health, fitness, and training status." These papers focus on 1) different assay methodologies for IGF-I within the paradigm of exercise studies, 2) research demonstrating that intracellular signaling components associated with several proinflammatory cytokines have the potential to interact with anabolic signaling processes in skeletal muscle, and 3) an overview of IGF-I as a biomarker related to exercise training, muscle and bone remodeling, body composition, cognition, and cancer. When summed in total, the contribution that these papers will make will undoubtedly involve bringing attention to the vast regulatory complexity of the IGF-I system and will hopefully convince the reader that the IGF-I system warrants further detailed scientific inquiry to resolve many unanswered questions and paradoxical experimental findings. The IGF-I system remains one of the most intriguing and captivating marvels of human physiology that seems central in mediating numerous adaptations from physical activity.

Photons Revisited

NASA Astrophysics Data System (ADS)

Batic, Matej; Begalli, Marcia; Han, Min Cheol; Hauf, Steffen; Hoff, Gabriela; Kim, Chan Hyeong; Kim, Han Sung; Grazia Pia, Maria; Saracco, Paolo; Weidenspointner, Georg

2014-06-01

A systematic review of methods and data for the Monte Carlo simulation of photon interactions is in progress: it concerns a wide set of theoretical modeling approaches and data libraries available for this purpose. Models and data libraries are assessed quantitatively with respect to an extensive collection of experimental measurements documented in the literature to determine their accuracy; this evaluation exploits rigorous statistical analysis methods. The computational performance of the associated modeling algorithms is evaluated as well. An overview of the assessment of photon interaction models and results of the experimental validation are presented.

Long-term effects of a factory closure: unemployment and disability during ten years' follow-up.

PubMed

Westin, S; Schlesselman, J J; Korper, M

1989-01-01

The consequences of a factory closure on future employment, disability and death were investigated in a 10-year prospective follow-up study in a general practice setting. The study population consisted of 85 persons who lost their jobs when a brisling sardine factory close to Bergen in Norway was shut down in 1975. The employees of a nearby "sister factory" within the same company were chosen as a control population, consisting of 87 persons. After the factory closure, the annual employment rate of the study group showed a steady rise to a maximum level of 44% within 6 years, but even after 10 years never matched the employment rate of the controls. The cumulative rates of disability pension, granted for medical conditions only, was more than three times higher in the study group than among controls from the second through the fourth year of follow-up. This excess of disabilities then stayed relatively constant at approximately 17 per 100 persons from 5 to 10 years after the shut-down. Given present days' unemployment, the results of this investigation point to the importance of acknowledging a long-term effect of job-loss on health and social readjustment.

[Status of lead exposure and its impact on health of workers in an accumulator factory].

PubMed

Liang, Jiabin; Zhang, Jian; Guo, Xiaojing; Mai, Jianping; Wang, Zhi; Liu, Yimin

2014-02-01

To identify the occupational hazard factors in an accumulator factory, to analyze the status of internal and external lead exposure and evaluate the impact of lead exposure on the health of workers in the accumulator industry, and to provide a theoretical basis for improved lead exposure criteria and technical support for the control of lead contamination in the accumulator industry. An on-site investigation was carried out to monitor and evaluate the lead fume and dust in the workplaces of an accumulator factory, and occupational health examination was performed in all workers. The occupational hazard safeguards in the accumulator factory were unadvanced. The contamination of lead fume and dust was serious. The abnormal rate of blood lead was up to 79.80%, and many workers developed anemia and mild peripheral nerve disease. Lead contamination is serious in the accumulator factory, leading to poor health of workers. It is essential to take effective control measures, improve the working environment, provide occupational health education, increase workers' self-protection awareness, and periodically conduct occupational hazard monitoring and health surveillance. The government must reinforce occupational health supervision of such enterprises.

Photonic structures in biology

NASA Astrophysics Data System (ADS)

Vukusic, Pete; Sambles, J. Roy

2003-08-01

Millions of years before we began to manipulate the flow of light using synthetic structures, biological systems were using nanometre-scale architectures to produce striking optical effects. An astonishing variety of natural photonic structures exists: a species of Brittlestar uses photonic elements composed of calcite to collect light, Morpho butterflies use multiple layers of cuticle and air to produce their striking blue colour and some insects use arrays of elements, known as nipple arrays, to reduce reflectivity in their compound eyes. Natural photonic structures are providing inspiration for technological applications.

Single photon quantum cryptography.

PubMed

Beveratos, Alexios; Brouri, Rosa; Gacoin, Thierry; Villing, André; Poizat, Jean-Philippe; Grangier, Philippe

2002-10-28

We report the full implementation of a quantum cryptography protocol using a stream of single photon pulses generated by a stable and efficient source operating at room temperature. The single photon pulses are emitted on demand by a single nitrogen-vacancy color center in a diamond nanocrystal. The quantum bit error rate is less that 4.6% and the secure bit rate is 7700 bits/s. The overall performances of our system reaches a domain where single photons have a measurable advantage over an equivalent system based on attenuated light pulses.

Solar Temporal Photon Bunching

NASA Astrophysics Data System (ADS)

Tan, Peng Kian

2018-04-01

Conventional ground-based astronomical observations suffer from image distortion due to atmospheric turbulence. Light from thermal blackbody radiators such as stars exhibits photon bunching behaviour at sufficiently short time-scales which should be independent from atmospherically induced phase fluctuations. However, this photon bunching signal is difficult to observe directly with available detector bandwidths. By performing narrowband spectral filtering on Sunlight and conducting temporal intensity interferometry using actively quenched avalanche photon detectors (APDs), the Solar g(2)(tau) signature was directly measured, consistently throughout the day despite fluctuating weather conditions, cloud cover and elevation angle.

Pollution characterization of liquid waste of the factory complex Fertial (Arzew, Algeria).

PubMed

Redouane, Fares; Mourad, Lounis

2016-03-01

The industrial development in Algeria has made a worrying situation for all socioeconomic stakeholders. Indeed, this economic growth is marked in recent years by the establishment of factories and industrial plants that discharge liquid waste in marine shorelines. These releases could destabilize the environmental balance in the coming years, hence the need to support the processing of all sources of pollution. Remediation of such discharges requires several steps of identifying the various pollutants to their treatments. Therefore, the authors conducted this first work of characterization of industrial effluents generated by the mineral fertilizer factory complex Fertial (Arzew), and discussed the pollution load generated by this type of industry. This monitoring would establish a tool for reflection and decision support developed by a management system capable of ensuring effective and sustainable management of effluents from industrial activities of Fertial. The authors conducted this first work of characterization of industrial effluents generated by the mineral fertilizer factory complex Fertial (Arzew), and discussed the pollution load generated by this type of industry. This monitoring would establish a tool for reflection and decision support developed by a management system capable of ensuring effective and sustainable management of effluents from industrial activities of Fertial.

Web-enabling technologies for the factory floor: a web-enabling strategy for emanufacturing

NASA Astrophysics Data System (ADS)

Velez, Ricardo; Lastra, Jose L. M.; Tuokko, Reijo O.

2001-10-01

This paper is intended to address the different technologies available for Web-enabling of the factory floor. It will give an overview of the importance of Web-enabling of the factory floor, in the application of the concepts of flexible and intelligent manufacturing, in conjunction with e-commerce. As a last section, it will try to define a Web-enabling strategy for the application in eManufacturing. This is made under the scope of the electronics manufacturing industry, so every application, technology or related matter is presented under such scope.

Lumber grade-yields for factory-grade northern red oak sawlogs

Treesearch

James G. Schroeder; Leland F. Hanks

1967-01-01

A report on results of sawing 556 northern red oak sawlogs at four sawmills in West Virginia and Virginia, and the distribution of grades for the standard factory lumber produced. Tabular data on actual yield and curved grade-yield percentages.

Isocyanate-induced asthma in a car factory.

PubMed

White, W G; Morris, M J; Sugden, E; Zapata, E

1980-04-05

In a car factory employing 203 women machinists making seat covers more women complained of respiratory symptoms after the introduction of a new seat cover fabric, cropped nylon backed with flame-bonded polyurethane foam (CNPF). 68 women working in the trim shop were studied on the first day back at work after a week's holiday and then at the end of a working week; the incidence of wheezing and/or shortness of breath was greater than expected but there was no difference between peak flow rates. A second study of 192 of the 203 women working in the trim shop confirmed this recent increase in incidence of asthmatic symptoms and showed that significantly more machinists who had worked with this new fabric had a reduced peak flow rate than machinists who had not. Asthma developed in one subject when she was working in the factory sewing CNPF, when she was handling this fabric in the challenge cabinet in the laboratory, and on challenge with toluene di-isocyanate in the laboratory. Airways resistance increased in 3 other workers after exposure to CNPF in the laboratory. Low concentrations (between 0.0003 to 0.003 ppm) of toluene di-isocyanate were found in the air around this fabric. 4 of 9 women with symptoms had IgE antibodies to toluene di-isocyanate.

Anomalous transparency in photonic crystals and its application to point-by-point grating inscription in photonic crystal fibers.

PubMed

Baghdasaryan, Tigran; Geernaert, Thomas; Chah, Karima; Caucheteur, Christophe; Schuster, Kay; Kobelke, Jens; Thienpont, Hugo; Berghmans, Francis

2018-04-03

It is common belief that photonic crystals behave similarly to isotropic and transparent media only when their feature sizes are much smaller than the wavelength of light. Here, we counter that belief and we report on photonic crystals that are transparent for anomalously high normalized frequencies up to 0.9, where the crystal's feature sizes are comparable with the free space wavelength. Using traditional photonic band theory, we demonstrate that the isofrequency curves can be circular in the region above the first stop band for triangular lattice photonic crystals. In addition, by simulating how efficiently a tightly focused Gaussian beam propagates through the photonic crystal slab, we judge on the photonic crystal's transparency rather than on isotropy only. Using this approach, we identified a wide range of photonic crystal parameters that provide anomalous transparency. Our findings indicate the possibility to scale up the features of photonic crystals and to extend their operational wavelength range for applications including optical cloaking and graded index guiding. We applied our result in the domain of femtosecond laser micromachining, by demonstrating what we believe to be the first point-by-point grating inscribed in a multi-ring photonic crystal fiber.

Apparatus for photon activation positron annihilation analysis

DOEpatents

Akers, Douglas W [Idaho Falls, ID

2007-06-12

Non-destructive testing apparatus according to one embodiment of the invention comprises a photon source. The photon source produces photons having predetermined energies and directs the photons toward a specimen being tested. The photons from the photon source result in the creation of positrons within the specimen being tested. A detector positioned adjacent the specimen being tested detects gamma rays produced by annihilation of positrons with electrons. A data processing system operatively associated with the detector produces output data indicative of a lattice characteristic of the specimen being tested.

Dual exposure, two-photon, conformal phasemask lithography for three dimensional silicon inverse woodpile photonic crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shir, Daniel J.; Nelson, Erik C.; Chanda, Debashis

2010-01-01

The authors describe the fabrication and characterization of three dimensional silicon inverse woodpile photonic crystals. A dual exposure, two-photon, conformal phasemask technique is used to create high quality polymer woodpile structures over large areas with geometries that quantitatively match expectations based on optical simulations. Depositing silicon into these templates followed by the removal of the polymer results in silicon inverse woodpile photonic crystals for which calculations indicate a wide, complete photonic bandgap over a range of structural fill fractions. Spectroscopic measurements of normal incidence reflection from both the polymer and siliconphotonic crystals reveal good optical properties.

Preparing technicians for photonics industries and organizations

NASA Astrophysics Data System (ADS)

Souders, John; Hull, Dan

2012-10-01

U.S. photonics organizations need about 800 new photonics technicians each year. Thirty-one community and technical colleges have approximately 700 students enrolled in photonics related programs; about 275 of them complete their coursework and enter the workforce each year. A disparity exists between the demand and supply of qualified photonics technicians in the U.S. OP-TEC, the National Center for Optics and Photonics Education is a consortium of seven colleges, under the leadership of the University of Central Florida, and sponsored by NSF. OP-TEC's mission is to increase the quantity and quality of photonics technicians prepared at two-year colleges. OP-TEC maintains the National Photonics Skill Standards for Technicians, provides curriculum models, teaching materials, faculty training/professional development and planning services to strengthen existing college photonics programs and to attract and support new ones. OP-TEC is converting its text materials to E-Books to support students in technical programs. Through OP-TEC's recruitment efforts 84 additional colleges are interested in initiating new photonics programs. The OP-TEC Photonics College Network (OPCN) consists of 28 colleges that are currently providing photonics education. This fall OPCN will lead an additional national effort to further educate employed photonics technicians through on-line courses, complemented by lab experiences at nearby colleges. OP-TEC is expanding its outreach to photonics employers and colleges by regionalizing its approach to offering its services. OP-TEC is also planning to develop new curricula and instructional materials for AAS programs to prepare Precision Optics Technicians. This paper will detail OP-TEC's work with particular emphases on its materials and services.

Raman-tailored photonic crystal fiber for telecom band photon-pair generation.

PubMed

Cordier, M; Orieux, A; Gabet, R; Harlé, T; Dubreuil, N; Diamanti, E; Delaye, P; Zaquine, I

2017-07-01

We report on the experimental characterization of a novel nonlinear liquid-filled hollow-core photonic crystal fiber for the generation of photon pairs at a telecommunication wavelength through spontaneous four-wave mixing (SFWM). We show that the optimization procedure in view of this application links the choice of the nonlinear liquid to the design parameters of the fiber, and we give an example of such an optimization at telecom wavelengths. Combining the modeling of the fiber and classical characterization techniques at these wavelengths, we identify for the chosen fiber and liquid combination SFWM phase-matching frequency ranges with no Raman scattering noise contamination. This is a first step toward obtaining a telecom band fibered photon-pair source with a high signal-to-noise ratio.

The Use of Factorial Forecasting to Predict Public Response

ERIC Educational Resources Information Center

Weiss, David J.

2012-01-01

Policies that call for members of the public to change their behavior fail if people don't change; predictions of whether the requisite changes will take place are needed prior to implementation. I propose to solve the prediction problem with Factorial Forecasting, a version of functional measurement methodology that employs group designs. Aspects…

Time-dependent photon migration imaging

NASA Astrophysics Data System (ADS)

Sevick, Eva M.; Wang, NaiGuang; Chance, Britton

1992-02-01

Recently, the application of both time- and frequency-resolved fluorescence techniques for the determination of photon migration characteristics in strongly scattering media has been used to characterize the optical properties in strongly scattering media. Specifically, Chance and coworkers have utilized measurement of photon migration characteristics to determine tissue hemoglobin absorbance and ultimately oxygenation status in homogeneous tissues. In this study, we present simulation results and experimental measurements for both techniques to show the capacity of time-dependent photon migration characteristics to image optically obscure absorbers located in strongly scattering media. The applications of time-dependent photon imaging in the biomedical community include imaging of light absorbing hematomas, tumors, hypoxic tissue volumes, and other tissue abnormalities. Herein, we show that the time-resolved parameter of mean photon path length, , and the frequency- resolved parameter of phase-shift, (theta) , can be used similarly to obtain three dimensional information of absorber position from two-dimensional measurements. Finally, we show that unlike imaging techniques that monitor the intensity of light without regard to the migration characteristics, the resolution of time-dependent photon migration measurements is enhanced by tissue scattering, further potentiating their use for biomedical imaging.

Spatial filtering with photonic crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maigyte, Lina; Staliunas, Kestutis; Institució Catalana de Recerca i Estudis Avançats

2015-03-15

Photonic crystals are well known for their celebrated photonic band-gaps—the forbidden frequency ranges, for which the light waves cannot propagate through the structure. The frequency (or chromatic) band-gaps of photonic crystals can be utilized for frequency filtering. In analogy to the chromatic band-gaps and the frequency filtering, the angular band-gaps and the angular (spatial) filtering are also possible in photonic crystals. In this article, we review the recent advances of the spatial filtering using the photonic crystals in different propagation regimes and for different geometries. We review the most evident configuration of filtering in Bragg regime (with the back-reflection—i.e., inmore » the configuration with band-gaps) as well as in Laue regime (with forward deflection—i.e., in the configuration without band-gaps). We explore the spatial filtering in crystals with different symmetries, including axisymmetric crystals; we discuss the role of chirping, i.e., the dependence of the longitudinal period along the structure. We also review the experimental techniques to fabricate the photonic crystals and numerical techniques to explore the spatial filtering. Finally, we discuss several implementations of such filters for intracavity spatial filtering.« less

Photon Beaming in External Compton models

NASA Astrophysics Data System (ADS)

Hutter, Anne; Spanier, Felix

In attempt to model blazar emission spectra, External Compton models have been employed to fit the observed data. In these models photons from the accretion disk or the CMB are upscat-tered via the Compton effect by the electrons and contribute to the emission. In previous works the resulting scattered photon angular distribution has been calculated for ultrarelativistic elec-trons. This work aims to extend the result to the case of mildly relativistic electrons. Hence, the beaming pattern produced by a relativistic moving blob consisting of isotropic distributed electrons, which scatter photons of an isotropic external radiation is calculated numerically. The isotropic photon density distribution in the blob frame is Lorentz-transformed into the rest frame of the electron and results in an anisotropic distribution with a preferred direction where it is upscattered by the electrons. The photon density distribution is determined and transformed back into the blob frame. As the photons in the rest frame of the electrons are dis-tributed anisotropically the scattering does not reproduce this anisotropic distribution. When transforming back into the blob frame the resulting photon distribution won't be isotropic. Approximations have shown that the resulting photon distribution is boosted more strongly than a distribution assumed to be isotropic in the rest frame of the electrons. Hence, in order to obtain the beaming caused by external Compton it is of particular interest to derive a more exact approximation of the resulting photon angular distribution.

Range detection using entangled optical photons

NASA Astrophysics Data System (ADS)

Brandsema, Matthew J.; Narayanan, Ram M.; Lanzagorta, Marco

2015-05-01

Quantum radar is an emerging field that shows a lot of promise in providing significantly improved resolution compared to its classical radar counterpart. The key to this kind of resolution lies in the correlations created from the entanglement of the photons being used. Currently, the technology available only supports quantum radar implementation and validation in the optical regime, as opposed to the microwave regime, because microwave photons have very low energy compared to optical photons. Furthermore, there currently do not exist practical single photon detectors and generators in the microwave spectrum. Viable applications in the optical regime include deep sea target detection and high resolution detection in space. In this paper, we propose a conceptual architecture of a quantum radar which uses entangled optical photons based on Spontaneous Parametric Down Conversion (SPDC) methods. After the entangled photons are created and emerge from the crystal, the idler photon is detected very shortly thereafter. At the same time, the signal photon is sent out towards the target and upon its reflection will impinge on the detector of the radar. From these two measurements, correlation data processing is done to obtain the distance of the target away from the radar. Various simulations are then shown to display the resolution that is possible.

Changing optical band structure with single photons

NASA Astrophysics Data System (ADS)

Albrecht, Andreas; Caneva, Tommaso; Chang, Darrick E.

2017-11-01

Achieving strong interactions between individual photons enables a wide variety of exciting possibilities in quantum information science and many-body physics. Cold atoms interfaced with nanophotonic structures have emerged as a platform to realize novel forms of nonlinear interactions. In particular, when atoms are coupled to a photonic crystal waveguide, long-range atomic interactions can arise that are mediated by localized atom-photon bound states. We theoretically show that in such a system, the absorption of a single photon can change the band structure for a subsequent photon. This occurs because the first photon affects the atoms in the chain in an alternating fashion, thus leading to an effective period doubling of the system and a new optical band structure for the composite atom-nanophotonic system. We demonstrate how this mechanism can be engineered to realize a single-photon switch, where the first incoming photon switches the system from being highly transmissive to highly reflective, and analyze how signatures can be observed via non-classical correlations of the outgoing photon field.

Single-Atom Single-Photon Quantum Interface

NASA Astrophysics Data System (ADS)

Moehring, David; Bochmann, Joerg; Muecke, Martin; Specht, Holger; Weber, Bernhard; Wilk, Tatjana; Rempe, Gerhard

2008-05-01

By combining atom trapping techniques and cavity cooling schemes we are able to trap a single neutral atom inside a high-finesse cavity for several tens of seconds. We show that our coupled atom-cavity system can be used to generate single photons in a controlled way. With our long trapping times and high single-photon production efficiency, the non-classical properties of the emitted light can be shown in the photon correlations of a single atom. In a similar atom-cavity setup, we investigate the interface between atoms and photons by entangling a single atom with a single photon emitted into the cavity and by further mapping the quantum state of the atom onto a second single photon. These schemes are intrinsically deterministic and establish the basic element required to realize a distributed quantum network with individual atoms at rest as quantum memories and single flying photons as quantum messengers. This work was supported by the Deutsche Forschungsgemeinschaft, and the European Union SCALA and CONQUEST programs. D. L. M. acknowledges support from the Alexander von Humboldt Foundation.

Microwave photonics with superconducting quantum circuits

NASA Astrophysics Data System (ADS)

Gu, Xiu; Kockum, Anton Frisk; Miranowicz, Adam; Liu, Yu-xi; Nori, Franco

2017-11-01

In the past 20 years, impressive progress has been made both experimentally and theoretically in superconducting quantum circuits, which provide a platform for manipulating microwave photons. This emerging field of superconducting quantum microwave circuits has been driven by many new interesting phenomena in microwave photonics and quantum information processing. For instance, the interaction between superconducting quantum circuits and single microwave photons can reach the regimes of strong, ultra-strong, and even deep-strong coupling. Many higher-order effects, unusual and less familiar in traditional cavity quantum electrodynamics with natural atoms, have been experimentally observed, e.g., giant Kerr effects, multi-photon processes, and single-atom induced bistability of microwave photons. These developments may lead to improved understanding of the counterintuitive properties of quantum mechanics, and speed up applications ranging from microwave photonics to superconducting quantum information processing. In this article, we review experimental and theoretical progress in microwave photonics with superconducting quantum circuits. We hope that this global review can provide a useful roadmap for this rapidly developing field.

Photonic Programmable Tele-Cloning Network.

PubMed

Li, Wei; Chen, Ming-Cheng

2016-06-29

The concept of quantum teleportation allows an unknown quantum states to be broadcasted and processed in a distributed quantum network. The quantum information injected into the network can be diluted to distant multi-copies by quantum cloning and processed by arbitrary quantum logic gates which were programed in advance in the network quantum state. A quantum network combines simultaneously these fundamental quantum functions could lead to new intriguing applications. Here we propose a photonic programmable telecloning network based on a four-photon interferometer. The photonic network serves as quantum gate, quantum cloning and quantum teleportation and features experimental advantage of high brightness by photon recycling.

Photonic Programmable Tele-Cloning Network

PubMed Central

Li, Wei; Chen, Ming-Cheng

2016-01-01

The concept of quantum teleportation allows an unknown quantum states to be broadcasted and processed in a distributed quantum network. The quantum information injected into the network can be diluted to distant multi-copies by quantum cloning and processed by arbitrary quantum logic gates which were programed in advance in the network quantum state. A quantum network combines simultaneously these fundamental quantum functions could lead to new intriguing applications. Here we propose a photonic programmable telecloning network based on a four-photon interferometer. The photonic network serves as quantum gate, quantum cloning and quantum teleportation and features experimental advantage of high brightness by photon recycling. PMID:27353838

What are single photons good for?

NASA Astrophysics Data System (ADS)

Sangouard, Nicolas; Zbinden, Hugo

2012-10-01

In a long-held preconception, photons play a central role in present-day quantum technologies. But what are sources producing photons one by one good for precisely? Well, in opposition to what many suggest, we show that single-photon sources are not helpful for point to point quantum key distribution because faint laser pulses do the job comfortably. However, there is no doubt about the usefulness of sources producing single photons for future quantum technologies. In particular, we show how single-photon sources could become the seed of a revolution in the framework of quantum communication, making the security of quantum key distribution device-independent or extending quantum communication over many hundreds of kilometers. Hopefully, these promising applications will provide a guideline for researchers to develop more and more efficient sources, producing narrowband, pure and indistinguishable photons at appropriate wavelengths.

Photonic liquid crystal fibers — a new challenge for fiber optics and liquid crystals photonics

NASA Astrophysics Data System (ADS)

Woliński, T. R.; Ertman, S.; Lesiak, P.; Domański, A. W.; Czapla, A.; Dąbrowski, R.; Nowinowski-Kruszelnicki, E.; Wójcik, J.

2006-12-01

The paper reviews and discusses the latest developments in the field of the photonic liquid crystal fibers that have occurred for the last three years in view of new challenges for both fiber optics and liquid crystal photonics. In particular, we present the latest experimental results on electrically induced birefringence in photonic liquid crystal fibers and discuss possibilities and directions of future developments.

Response of furniture factory workers to work-related airborne allergens.

PubMed

Skórska, Czesława; Krysińska-Traczyk, Ewa; Milanowski, Janusz; Cholewa, Grazyna; Sitkowska, Jolanta; Góra, Anna; Dutkiewicz, Jacek

2002-01-01

The aim of this work was to determine the reactivity of furniture factory workers to microbial allergens associated with wood dust. Allergological examinations by skin and precipitin tests were performed in 48 workers employed in a factory producing furniture from fibreboards and chipboards, and in 32 healthy urban dwellers not exposed to organic dusts (referents). The skin test was performed by the intradermal method with the saline extracts of the cultures of 3 microbial species (Rahnella sp., Arthrobacter globiformis, Aspergillus fumigatus) associated with wood dust. Skin reactions were recorded after 20 minutes, 8 hours and 24 hours and graded 1-4, depending on the diameter of the reaction. The agar-gel test for the presence of precipitins in serum was performed with the extracts of 15 microbial isolates. The furniture factory workers showed a high skin response to the extracts of environmental microbes. The frequency of early grade 2 reactions (diameter 10 mm) to the extract of Rahnella sp. was 64.6% among furniture workers, being significantly higher (p < 0.001) compared to reference group (18.7%). High frequencies of grade 2 reactions in furniture workers were also found with the extracts of A. globiformis and A. fumigatus (52.1% and 62.5%, respectively). The frequencies of grade 2 delayed (after 8 h) and late (after 24 h) reactions to Rahnella sp. in furniture workers were non-specifically high (97.9%/93.7%) while the response rates to A. globiformis and A. fumigatus were much lower (10.4%/25.0%, and 4.2%/37.5%, respectively). In agar-gel test for detection of precipitins, in most cases very low percentages of positive reactions (0-2.1%) were noted in furniture factory workers. The only exception was a high percentage of positive reactions (27.1%) to the antigen of Pseudomonas maltophilia, which was significantly greater in furniture workers compared to the reference group (p < 0.01). The obtained results suggest that early allergic reactions to

Active temporal multiplexing of indistinguishable heralded single photons

PubMed Central

Xiong, C.; Zhang, X.; Liu, Z.; Collins, M. J.; Mahendra, A.; Helt, L. G.; Steel, M. J.; Choi, D. -Y.; Chae, C. J.; Leong, P. H. W.; Eggleton, B. J.

2016-01-01

It is a fundamental challenge in quantum optics to deterministically generate indistinguishable single photons through non-deterministic nonlinear optical processes, due to the intrinsic coupling of single- and multi-photon-generation probabilities in these processes. Actively multiplexing photons generated in many temporal modes can decouple these probabilities, but key issues are to minimize resource requirements to allow scalability, and to ensure indistinguishability of the generated photons. Here we demonstrate the multiplexing of photons from four temporal modes solely using fibre-integrated optics and off-the-shelf electronic components. We show a 100% enhancement to the single-photon output probability without introducing additional multi-photon noise. Photon indistinguishability is confirmed by a fourfold Hong–Ou–Mandel quantum interference with a 91±16% visibility after subtracting multi-photon noise due to high pump power. Our demonstration paves the way for scalable multiplexing of many non-deterministic photon sources to a single near-deterministic source, which will be of benefit to future quantum photonic technologies. PMID:26996317

Smart factory in the context of 4th industrial revolution: challenges and opportunities for Romania

NASA Astrophysics Data System (ADS)

Pîrvu, B. C.; Zamfirescu, C. B.

2017-08-01

Manufacturing companies, independent of operation sector and size, must be able to produce lot size one products, just-in-time at a competitive cost. Coping with this high adaptability and short reaction times proves to be very challenging. New approaches must be taken into consideration for designing modular, intelligent and cooperative production systems which are easy to integrate with the entire factory. The coined term for this network of intelligent interacting artefacts system is cyber-physical systems (CPS). CPS is often used in the context of Industry 4.0 - or what many consider the forth industrial revolution. The paper presents an overview of key technological and social requirements to map the Smart Factory vision into reality. Finally, global and Romanian specific challenges hindering the vision of a true Smart Factory to become reality are presented.

Luminescence spectra of a cholesteric photonic crystal

NASA Astrophysics Data System (ADS)

Dolganov, P. V.

2017-05-01

The transmission and luminescence spectra of a cholesteric photonic crystal doped with an organic dye are measured. The density of photon states is calculated using the material parameters obtained from the comparison of the experimental and theoretical spectra. The shape of the luminescence spectra is modified with respect to the density of photon states owing to the difference in the structure of the normal modes of the photonic crystal near the short-wavelength and long-wavelength edges of the photonic quasi-band gap upon the "pushing" of the photon states from the gap and to the nonvanishing orientation ordering of the luminescent molecules. The luminescence spectrum calculated taking into account the chiral structure of the photonic crystal agrees with the experimental spectrum.

CP Violation and the Future of Flavor Physics

NASA Astrophysics Data System (ADS)

Kiesling, Christian

2009-12-01

With the nearing completion of the first-generation experiments at asymmetric e+e- colliders running at the Υ(4S) resonance ("B-Factories") a new era of high luminosity machines is at the horizon. We report here on the plans at KEK in Japan to upgrade the KEKB machine ("SuperKEKB") with the goal of achieving an instantaneous luminosity exceeding 8×1035 cm-2 s-1, which is almost two orders of magnitude higher than KEKB. Together with the machine, the Belle detector will be upgraded as well ("Belle-II"), with significant improvements to increase its background tolerance as well as improving its physics performance. The new generation of experiments is scheduled to take first data in the year 2013.

Patient-Specific B-Cell Antibody Factories to Treat Metastatic Disease

DTIC Science & Technology

2013-08-01

Immortalization of these selected clones using Epstein - Barr viral transformation provides a method to maintain these antibody producing cell lines as a...2013 Please see next page. None provided. Patient-Specific B-Cell Antibody Factories to Treat Metastatic Disease Kevin Claffey University of

Review of Microwave Photonics Technique to Generate the Microwave Signal by Using Photonics Technology

NASA Astrophysics Data System (ADS)

Raghuwanshi, Sanjeev Kumar; Srivastav, Akash

2017-12-01

Microwave photonics system provides high bandwidth capabilities of fiber optic systems and also contains the ability to provide interconnect transmission properties, which are virtually independent of length. The low-loss wide bandwidth capability of optoelectronic systems makes them attractive for the transmission and processing of microwave signals, while the development of high-capacity optical communication systems has required the use of microwave techniques in optical transmitters and receivers. These two strands have led to the development of the research area of microwave photonics. So, we can considered microwave photonics as the field that studies the interaction between microwave and optical waves for applications such as communications, radars, sensors and instrumentations. In this paper we have thoroughly reviewed the microwave generation techniques by using photonics technology.

Fuel Effective Photonic Propulsion

NASA Astrophysics Data System (ADS)

Rajalakshmi, N.; Srivarshini, S.

2017-09-01

With the entry of miniaturization in electronics and ultra-small light-weight materials, energy efficient propulsion techniques for space travel can soon be possible. We need to go for such high speeds so that the generation’s time long interstellar missions can be done in incredibly short time. Also renewable energy like sunlight, nuclear energy can be used for propulsion instead of fuel. These propulsion techniques are being worked on currently. The recently proposed photon propulsion concepts are reviewed, that utilize momentum of photons generated by sunlight or onboard photon generators, such as blackbody radiation or lasers, powered by nuclear or solar power. With the understanding of nuclear photonic propulsion, in this paper, a rough estimate of nuclear fuel required to achieve the escape velocity of Earth is done. An overview of the IKAROS space mission for interplanetary travel by JAXA, that was successful in demonstrating that photonic propulsion works and also generated additional solar power on board, is provided; which can be used as a case study. An extension of this idea for interstellar travel, termed as ‘Star Shot’, aims to send a nanocraft to an exoplanet in the nearest star system, which could be potentially habitable. A brief overview of the idea is presented.

Smoking intensity among male factory workers in Kunming, China.

PubMed

Cheng, Kai-Wen; Tsoh, Janice Y; Cui, Wenlong; Li, Xiaoliang; Kohrman, Matthew

2015-03-01

This study investigated the intensity of cigarette consumption and its correlates in China among urban male factory workers, a cohort especially vulnerable to tobacco exposure, one that appears to have benefitted little from recent public health efforts to reduce smoking rates. Data were collected from men working in factories of Kunming city, Yunnan, China, who are current daily smokers (N = 490). A multinomial logistic regression was conducted to examine the factors in association with smoking intensity in light, moderate, and heavy levels. Light smoking correlated with social smoking, smoking the first cigarette later in the day, self-reported health condition, and quit intention. Heavy smoking was associated with purchase of lower priced cigarettes, difficulty refraining from smoking, and prehypertensive blood pressure. Even in regions where smoking is highly prevalent, even among cohorts who smoke heavily, variation exists in how cigarettes are consumed. Analyses of this consumption, with special consideration given to smoking intensity and its correlates, can help guide tobacco-control strategists in developing more effective interventions. © 2013 APJPH.

Rank-based permutation approaches for non-parametric factorial designs.

PubMed

Umlauft, Maria; Konietschke, Frank; Pauly, Markus

2017-11-01

Inference methods for null hypotheses formulated in terms of distribution functions in general non-parametric factorial designs are studied. The methods can be applied to continuous, ordinal or even ordered categorical data in a unified way, and are based only on ranks. In this set-up Wald-type statistics and ANOVA-type statistics are the current state of the art. The first method is asymptotically exact but a rather liberal statistical testing procedure for small to moderate sample size, while the latter is only an approximation which does not possess the correct asymptotic α level under the null. To bridge these gaps, a novel permutation approach is proposed which can be seen as a flexible generalization of the Kruskal-Wallis test to all kinds of factorial designs with independent observations. It is proven that the permutation principle is asymptotically correct while keeping its finite exactness property when data are exchangeable. The results of extensive simulation studies foster these theoretical findings. A real data set exemplifies its applicability. © 2017 The British Psychological Society.

Platinum Acetylide Two-Photon Chromophores (Postprint)

DTIC Science & Technology

2007-01-01

two lower- energy photons results in initiation of the same photophysical processes as one-photon absorption (1PA) of one high- energy photon. This is...advantageous for two reasons. First, by using lower- energy photons, a material will be protected from photodegradation effects. Second, the quadratic...D. L.; Ehrlich, J. E.; Erskine , L. L.; Heikal, A. A.; Kuebler, S. M.; Le, I. Y. S.; McCord-Maughon, D.; Qin, J.; Rockel, H.; Rumi, M.; Wu, X. L

EDITORIAL: Special issue on green photonics Special issue on green photonics

NASA Astrophysics Data System (ADS)

Boardman, Allan; Brongersma, Mark; Polman, Albert

2012-02-01

Photovoltaic (PV) cells can provide virtually unlimited amounts of energy by effectively converting sunlight into clean electrical power. Over the years, significant research and development efforts have been devoted to improving the structural and charge transport properties of the materials used in PV cells. Despite these efforts, the current energy conversion efficiencies of commercial solar cells are still substantially lower than the ultimate limits set by thermodynamics. Economic arguments in addition to the scarcity of some semiconductors and materials used in transparent conductive oxides are also driving us to use less and less material in a cell. For these reasons, it is clear that new approaches need to be found. One possible solution that is more-or-less orthogonal to previous approaches is aimed at managing the photons rather than the electrons or atoms in a cell. This type of photon management is termed Green Photonics. Nano- and micro-photonic trapping techniques are currently gaining significant attention. The use of engineered plasmonic and high refractive index structures shows tremendous potential for enhancing the light absorption per unit volume in semiconductors. Unfortunately, the design space in terms of the nanostructure sizes, shapes, and array structures is too large to allow for optimization of PV cells using brute force simulations. For this reason, new intuitive models and rapid optimization techniques for advanced light trapping technologies need to be developed. At the same time we need to come up with new, inexpensive, and scalable nanostructure fabrication and optical characterization techniques in order to realize the dream of inexpensive, high power conversion efficiency cells that make economic sense. This special issue discusses some of the exciting new approaches to light trapping that leverage the most recent advances in the field of nanophotonics. It also provides some insights into why giving the green light to green

Observation of Genuine Three-Photon Interference

NASA Astrophysics Data System (ADS)

Agne, Sascha; Kauten, Thomas; Jin, Jeongwan; Meyer-Scott, Evan; Salvail, Jeff Z.; Hamel, Deny R.; Resch, Kevin J.; Weihs, Gregor; Jennewein, Thomas

2017-04-01

Multiparticle quantum interference is critical for our understanding and exploitation of quantum information, and for fundamental tests of quantum mechanics. A remarkable example of multi-partite correlations is exhibited by the Greenberger-Horne-Zeilinger (GHZ) state. In a GHZ state, three particles are correlated while no pairwise correlation is found. The manifestation of these strong correlations in an interferometric setting has been studied theoretically since 1990 but no three-photon GHZ interferometer has been realized experimentally. Here we demonstrate three-photon interference that does not originate from two-photon or single photon interference. We observe phase-dependent variation of three-photon coincidences with (92.7 ±4.6 )% visibility in a generalized Franson interferometer using energy-time entangled photon triplets. The demonstration of these strong correlations in an interferometric setting provides new avenues for multiphoton interferometry, fundamental tests of quantum mechanics, and quantum information applications in higher dimensions.