Final report, ongoing key comparison BIPM.QM-K1, ozone at ambient level, comparison with ISCIII (December 2014)

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Idrees, Faraz; Wielgosz, Robert; Sanchez, Carmen; Morillo Gomez, Pilar

2015-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Instituto de Salud Carlos III (ISCIII) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report of the APMP water flow key comparison: APMP.M.FF-K1

NASA Astrophysics Data System (ADS)

Lee, Kwang-Bock; Chun, Sejong; Terao, Yoshiya; Thai, Nguyen Hong; Tsair Yang, Cheng; Tao, Meng; Gutkin, Mikhail B.

2011-01-01

The key comparison, APMP.M.FF-K1, was undertaken by APMP/TCFF, the Technical Committee for Fluid Flow (TCFF) under the Asia Pacific Metrology Program (APMP). One objective of the key comparison was to demonstrate the degree of equivalence among six participating laboratories (KRISS, NMIJ, VMI, CMS, NIM and VNIIM) in water flow rate metrology by comparing the results with the key comparison reference value (KCRV) determined from the CCM.FF-K1 key comparison. The other objective of this key comparison was to provide supporting evidence for the calibration and measurement capabilities (CMCs), which had been declared by the participating laboratories during this key comparison. The Transfer Standard Package (TSP) was a Coriolis mass flowmeter, which had been used in the CCM.FF-K1 key comparison. Because the K-factors in the APMP.M.FF-K1 key comparison were slightly lower than the K-factors of the CCM.FF-K1 key comparison due to long-term drifts of the TSP, a correction value D was introduced. The value of D was given by a weighted sum between two link laboratories (NMIJ and KRISS), which participated in both the CCM.FF-K1 and the APMP.M.FF-K1 key comparisons. By this correction, the K-factors were laid between 12.004 and 12.017 at either low (Re = 254 000) or high (Re = 561 000) flow rates. Most of the calibration data were within expected uncertainty bounds. However, some data showed undulations, which gave large fluctuations of the metering factor at Re = 561 000. Calculation of degrees of equivalence showed that all the participating laboratories had deviations between -0.009 and 0.007 pulses/kg from the CCM.FF-K1 KCRV at either the low or the high flow rates. In case of En calculation, all the participating laboratories showed values less than 1, indicating that the corrected K-factors of all the laboratories were equivalent with the KCRV at both Re = 254 000 and 561 000. When the corrected K-factors from two participating laboratories were compared, all the

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with ISCIII, March 2017

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Wielgosz, Robert; Sanchez, Carmen; Morillo Gomez, Pilar

2017-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Instituto de Salud Carlos III (ISCIII) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with NPL, April 2017

NASA Astrophysics Data System (ADS)

Viallon, Joële; Idrees, Faraz; Moussay, Philippe; Wielgosz, Robert; Sweeney, Bryan; Quincey, Paul

2018-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone standard of the United Kingdom maintained by the National Physical Laboratory (NPL) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with VSL, September 2016

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Wielgosz, Robert; Heikens, Dita; van der Veen, Adrian

2017-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Netherlands maintained by the Van Swinden (VSL) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range from 0 nmol/mol to 500 nmol/mol Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with NIST, July 2015

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Wielgosz, Robert; Hodges, Joe; Norris, James E.

2017-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the National Institute of Standards and Technology (NIST) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with INECC, September 2017

NASA Astrophysics Data System (ADS)

Viallon, Joële; Idrees, Faraz; Moussay, Philippe; Wielgosz, Robert; Fentanes, Oscar; Benítez, Ángeles; Ordoñez, Daniel

2018-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of Mexico maintained by the National Institute of Ecology and Climate Change (INECC) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range from 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report of the key comparison of APMP.AUV.V-K2

NASA Astrophysics Data System (ADS)

Usuda, Takashi; Ota, Akihiro; Nozato, Hideaki; Ishigami, Tamio; Kokuyama, Wataru; Plangsangmas, Virat; Rattanangkul, Pairoj; Yih Tsuei, Kuang; Huang, Yu-Chung; Chee Keong, Chan; Shan, Cui

2017-01-01

A key comparison of vibration acceleration APMP.AUV.V-K2, which is an upgrade from APMP.AUV.V-K1.1, has been made within the Asia Pacific Metrology Programme (APMP) to include three national laboratories; the CMS-ITRI (Chinese Taipei), the NIMT (Thailand) and the A*Star (Singapore). One pilot laboratory, the NMIJ (Japan), participated to link the RMO APMP results to the CIPM CC key comparison (CCAUV.V-K2), according to the decision of the CCAUV10/D7 during the 10th CCAUV meeting. The admissible acceleration amplitude ranges from 10 m/s2 to 200 m/s2 over the frequency range from 40 Hz to 5 kHz. The RMO APMP results demonstrate the agreement with the key comparison reference value of CCAUV.V-K2 within the expanded uncertainties considering the armature effect of vibration exciter in a high-frequency range. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Updated Mars Mission Architectures Featuring Nuclear Thermal Propulsion

NASA Technical Reports Server (NTRS)

Rodriguez, Mitchell A.; Percy, Thomas K.

2017-01-01

Nuclear thermal propulsion (NTP) can potentially enable routine human exploration of Mars and the solar system. By using nuclear fission instead of a chemical combustion process, and using hydrogen as the propellant, NTP systems promise rocket efficiencies roughly twice that of the best chemical rocket engines currently available. The most recent major Mars architecture study featuring NTP was the Design Reference Architecture 5.0 (DRA 5.0), performed in 2009. Currently, the predominant transportation options being considered are solar electric propulsion (SEP) and chemical propulsion; however, given NTP's capabilities, an updated architectural analysis is needed. This paper provides a top-level overview of several different architectures featuring updated NTP performance data. New architectures presented include a proposed update to the DRA 5.0 as well as an investigation of architectures based on the current Evolvable Mars Campaign, which is the focus of NASA's current analyses for the Journey to Mars. Architectures investigated leverage the latest information relating to NTP performance and design considerations and address new support elements not available at the time of DRA 5.0, most notably the Orion crew module and the Space Launch System (SLS). The paper provides a top level quantitative comparison of key performance metrics as well as a qualitative discussion of improvements and key challenges still to be addressed. Preliminary results indicate that the updated NTP architectures can significantly reduce the campaign mass and subsequently the costs for assembly and number of launches.

SIM key comparison for luminous flux. SIM.PR-K4

NASA Astrophysics Data System (ADS)

Matamoros, Carlos H.; Ohno, Yoshi; Zwinkels, Joanne; Cogno, Jorge A.; Couceiro, Iakyra B.

2016-01-01

In compliance with the established BIPM and CCPR policies and guidelines on comparisons, the SIM Photometry and Radiometry Working Group decided to conduct a key comparison on total luminous flux in order to provide an opportunity for its member National Metrology Institutes (NMIs) that did not participate in the CCPR-K4 comparison, to get a link to the reference value obtained for this quantity (the lumen) and to derive the corresponding degrees of equivalence. This SIM.PR-K4 was piloted by Centro Nacional de Metrología (CENAM), the NMI of Mexico and included the participation of five laboratories: CENAM (Mexico), INTI (Argentina), INMETRO (Brazil), NIST (USA, linking lab), and NRC (Canada, linking lab). The comparison, conducted in star type scheme, was run using three to four lamps per participant, and results are given in this report, including the unilateral degrees of equivalence. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

The comparison and analysis of extracting video key frame

NASA Astrophysics Data System (ADS)

Ouyang, S. Z.; Zhong, L.; Luo, R. Q.

2018-05-01

Video key frame extraction is an important part of the large data processing. Based on the previous work in key frame extraction, we summarized four important key frame extraction algorithms, and these methods are largely developed by comparing the differences between each of two frames. If the difference exceeds a threshold value, take the corresponding frame as two different keyframes. After the research, the key frame extraction based on the amount of mutual trust is proposed, the introduction of information entropy, by selecting the appropriate threshold values into the initial class, and finally take a similar mean mutual information as a candidate key frame. On this paper, several algorithms is used to extract the key frame of tunnel traffic videos. Then, with the analysis to the experimental results and comparisons between the pros and cons of these algorithms, the basis of practical applications is well provided.

Sea snakes in Australian waters (Serpentes: subfamilies Hydrophiinae and Laticaudinae)--a review with an updated identification key.

PubMed

Rasmussen, Arne Redsted; Sanders, Kate Laura; Guinea, Michael L; Amey, Andrew P

2014-10-02

Sea snakes (Elapidae, subfamilies Hydrophiinae and Laticaudinae) reach high species richness in the South China Sea and in the Australian region; however, most countries in the two regions still lack up-to-date checklists and identification tools for these snakes. We present an updated reviewed checklist and a new complete identification key to sea snakes in Australian waters. The identification key includes 29 species documented and 4 possibly occurring taxa and is based mostly on easy-to-use external characters. We find no evidence for breeding populations of Laticauda in Australian waters, but include the genus on the list of possibly occurring taxa. 

KEY COMPARISON Report to the CCT on key comparison EUROMET.T-K6 (EUROMET Project no. 621): Comparison of the realizations of local dew/frost-point temperature scales in the range -50 °C to +20 °C

NASA Astrophysics Data System (ADS)

Heinonen, Martti

2010-01-01

The first humidity CIPM key comparison, CCT-K6, will be completed in 2010. The corresponding European regional key comparison, EUROMET.T-K6, was carried out in 2004 to 2008. National metrology institutes from 24 countries participated in the comparison. The comparison covered the dew-point temperature range from -50 °C to +20 °C. It was organized as three parallel loops with two specially manufactured precision chilled mirror hygrometers as transfer standards in each loop. The comparison scheme was designed to ensure high quality results with evenly spread workload for the participants. MIKES was coordinating the project. This report presents the results of the comparison and provides detailed information on the measurements performed by all participating laboratories and the analysis of the results. Conclusions on the equivalence of the dew-point temperature standards are drawn on the basis of calculated bilateral degrees of equivalence and deviations from EURAMET comparison reference values (ERV). Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Secure SCADA communication by using a modified key management scheme.

PubMed

Rezai, Abdalhossein; Keshavarzi, Parviz; Moravej, Zahra

2013-07-01

This paper presents and evaluates a new cryptographic key management scheme which increases the efficiency and security of the Supervisory Control And Data Acquisition (SCADA) communication. In the proposed key management scheme, two key update phases are used: session key update and master key update. In the session key update phase, session keys are generated in the master station. In the master key update phase, the Elliptic Curve Diffie-Hellman (ECDH) protocol is used. The Poisson process is also used to model the Security Index (SI) and Quality of Service (QoS). Our analysis shows that the proposed key management not only supports the required speed in the MODBUS implementation but also has several advantages compared to other key management schemes for secure communication in SCADA networks. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Final report, on-going key comparison BIPM.QM-K1: ozone at ambient level, comparison with DMDM, July 2015

NASA Astrophysics Data System (ADS)

Viallon, J.; Moussay, P.; Wielgosz, R.; Bebic, J.; Norris, J. E.; Guenther, F.

2016-01-01

As part of the on-going key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Directorate of Measures and Precious Metals (DMDM) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM), via a transfer standard maintained by the National Institute of Standards and Technology (NIST). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with NMISA, June 2017

NASA Astrophysics Data System (ADS)

Viallon, Joële; Idrees, Faraz; Moussay, Philippe; Wielgosz, Robert; Ntsasa, Napo G.; Tshilongo, James; Mphaphuli, Gumani E.; Norris, James E.; Hodges, Joseph T.

2018-01-01

As part of the on-going key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of South Africa maintained by the National Metrology Institute of South Africa (NMISA) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM), via a transfer standard maintained by the National Institute of Standards and Technology (NIST). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on the ongoing key comparison BIPM.QM-K1: Ozone at ambient level, comparison with ISCIII (December 2010)

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Idrees, Faraz; Wielgosz, Robert; Morillo Gomez, Pilar; Sánchez, Carmen

2011-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Instituto de Salud Carlos III (ISCIII) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report on the ongoing key comparison BIPM.QM-K1: Ozone at ambient level, comparison with ISCIII (December 2012)

NASA Astrophysics Data System (ADS)

Viallon, Joële; Moussay, Philippe; Idrees, Faraz; Wielgosz, Robert; Morillo Gomez, Pilar; Sánchez, Carmen

2013-01-01

As part of the ongoing key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the Instituto de Salud Carlos III (ISCIII) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: CCQM-K27-Subsequent: Key Comparison (subsequent) for the determination of ethanol in aqueous matrix

NASA Astrophysics Data System (ADS)

Schantz, Michele M.; Duewer, David L.; Parris, Reenie M.; May, Willie E.; Archer, Marcellé; Mussell, Chris; Carter, David; Konopelko, Leonid A.; Kustikov, Yury A.; Krylov, Anatoli I.; Fatina, Olga V.

2005-01-01

Ethanol is important both forensically ('drunk driving' or driving while under the influence, 'DWI', regulations) and commercially (alcoholic beverages). Blood- and breath-alcohol testing can be imposed on individuals operating private vehicles such as cars, boats, or snowmobiles, or operators of commercial vehicles like trucks, planes, and ships. The various levels of blood alcohol that determine whether these operators are considered legally impaired vary depending on the circumstances and locality. Accurate calibration and validation of instrumentation is critical in areas of forensic testing where quantitative analysis directly affects the outcome of criminal prosecutions, as is the case with the determination of ethanol in blood and breath. Additionally, the accurate assessment of the alcoholic content of beverages is a commercially important commodity. In 2002, the CCQM conducted a Key Comparison (CCQM-K27) for the determination of ethanol in aqueous matrix with nine participants. A report on this project has been approved by the CCQM and can be found at the BIPM website and in this Technical Supplement. CCQM-K27 comprised three samples, one at low mass fraction of ethanol in water (nominal concentration of 0.8 mg/g), one at high level (nominal concentration of 120 mg/g), and one wine matrix (nominal concentration of 81 mg/g). Overall agreement among eight participants using gas chromatography with flame ionization detection (GC-FID), titrimetry, isotope dilution gas chromatography/mass spectrometry (GC-IDMS), and gas chromatography-combustion-isotope ratio mass spectrometry (ID-GC-C-IRMS) was good. The ninth participant used a headspace GC-FID method that had not been validated in an earlier pilot study (CCQM-P35). A follow-on Key Comparison, CCQM-K27-Subsequent, was initiated in 2003 to accommodate laboratories that had not been ready to benchmark their methods in the original CCQM-K27 study or that wished to benchmark a different method. Four levels of

Report of the key comparison APMP.QM-K19. APMP comparison on pH measurement of borate buffer

NASA Astrophysics Data System (ADS)

Hioki, Akiharu; Asakai, Toshiaki; Maksimov, Igor; Suzuki, Toshihiro; Miura, Tsutomu; Obromsook, Krairerk; Tangpaisarnkul, Nongluck; Rodruangthum, Patumporn; Wong, Siu-Kay; Lam, Wai-Hing; Zakaria, Osman; Anuar Mohd. Amin, Khirul; Thanh, Ngo Huy; Máriássy, Michal; Vyskocil, Leos; Hankova, Zuzana; Fisicaro, Paola; Stoica, Daniela; Singh, Nahar; Soni, Daya; Ticona Canaza, Galia; Kutovoy, Viatcheslav; Barbieri Gonzaga, Fabiano; Dias, Júlio Cesar; Vospelova, Alena; Bakovets, Nickolay; Zhanasbayeva, Bibinur

2015-01-01

The APMP.QM-K19 was organised by TCQM of APMP to test the abilities of the national metrology institutes in the APMP region to measure a pH value of a borate buffer. This APMP comparison on pH measurement was proposed by the National Metrology Institute of Japan (NMIJ) and the National Institute of Metrology (Thailand) (NIMT) at the APMP-TCQM meeting held 26-27 November 2012. After approval by TCQM, the comparison has been conducted by NMIJ and NIMT. The comparison is a key comparison following CCQM-K19 and CCQM-K19.1. The comparison material was a borate buffer of pH around 9.2 and the measurement temperatures were 15 °C, 25 °C and 37 °C. This is the second APMP key comparison on pH measurement and the fourth APMP comparison on pH measurement following APMP.QM-P06 (two phosphate buffers) in 2004, APMP.QM-P09 (a phthalate buffer) in 2006 and APMP.QM-K9/APMP.QM-P16 (a phosphate buffer) in 2010-2011. The results can be used further by any participant to support its CMC claim at least for a borate buffer. That claim will concern the pH method employed by the participant during this comparison and will cover the used temperature(s) or the full temperature range between 15°C and 37 °C for the participant which measured pH values at the three temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on the key comparison CCPR-K5: Spectral diffuse reflectance

NASA Astrophysics Data System (ADS)

Nadal, Maria; Eckerle, Kenneth L.; Early, Edward A.; Ohno, Yoshi

2013-01-01

The CCPR K5 key comparison on spectral diffuse reflectance was carried out in the framework of the CIPM Mutual Recognition Arrangement, by 13 national metrology institutes (MMIs) as participants. The participants were CSIR-NML (South Africa), HUT (Finland), IFA-CSIC (Spain), KRISS (Republic of Korea), MSL (New Zealand), NIM (China), NIST (United States of America), NMIJ (Japan), NPL (United Kingdom), NRC (Canada), OMH (Hungary), PTB (Germany) and VNIIOFI (Russia Federation). NIST (USA) piloted the comparison. The aim of this comparison was to check the agreement of measurement of the spectral diffuse reflectance among participants, using the measurement geometry of d/0 or 0/d in the wavelength range of 360 nm to 820 nm at 20 nm increment. The comparison was a star type comparison with the samples provided by the pilot laboratory and with the measurement sequence: Pilot-Participant-Pilot. Spectralon and matte white ceramic tiles were used as the transfer standards. Each participant received three of each type of sample and at least one sample of each type was measured three times on three separate days, and the other two samples were measured once. The report presents the description of the measurement facilities, procedures and uncertainties of all the participants as well as the results of the comparison. Measurement results from the participants and their associated uncertainties were analyzed in accordance with the Guidelines for CCPR Key Comparison Report Preparation, using weighted mean with cut-off. For the calculation of the Key Comparison Reference Value (KCRV), as agreed by the participants, the data of both samples were used for the 460 nm to 820 nm region and only the data of the Spectralon samples were used in the spectral region of 360 nm to 440 nm. The unilateral degrees of equivalence (DoE) calculated for each participant are mostly consistent within the uncertainty (k = 2) of the DoE. This international comparison of spectral diffuse reflectance

Final report, on-going key comparison BIPM.QM-K1, ozone at ambient level, comparison with CMS-ITRI, June 2016

NASA Astrophysics Data System (ADS)

Viallon, Joële; Idrees, Faraz; Moussay, Philippe; Wielgosz, Robert; Lin, Tsai-Yin; Norris, James E.; Hodges, Joseph T.

2017-01-01

As part of the on-going key comparison BIPM.QM-K1, a comparison has been performed between the ozone national standard of the ITRI Center for Measurement Standards (CMS-ITRI) and the common reference standard of the key comparison, maintained by the Bureau International des Poids et Mesures (BIPM), via a transfer standard maintained by the National Institute of Standards and Technology (NIST). The instruments have been compared over a nominal ozone amount-of-substance fraction range of 0 nmol/mol to 500 nmol/mol. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Regional comparison of absolute gravimeters, EURAMET.M.G-K2 key comparison

NASA Astrophysics Data System (ADS)

Pálinkáš, V.; Francis, O.; Val'ko, M.; Kostelecký, J.; Van Camp, M.; Castelein, S.; Bilker-Koivula, M.; Näränen, J.; Lothhammer, A.; Falk, R.; Schilling, M.; Timmen, L.; Iacovone, D.; Baccaro, F.; Germak, A.; Biolcati, E.; Origlia, C.; Greco, F.; Pistorio, A.; De Plaen, R.; Klein, G.; Seil, M.; Radinovic, R.; Reudink, R.; Dykowski, P.; Sȩkowski, M.; Próchniewicz, D.; Szpunar, R.; Mojzeš, M.; Jańk, J.; Papčo, J.; Engfeldt, A.; Olsson, P. A.; Smith, V.; van Westrum, D.; Ellis, B.; Lucero, B.

2017-01-01

In the framework of the regional EURAMET.M.G-K2 comparison of absolute gravimeters, 17 gravimeters were compared in November 2015. Four gravimeters were from different NMIs and DIs, they were used to link the regional comparison to the CCM.G.K2 by means of linking converter. Combined least-squares adjustments with weighted constraint was used to determine KCRV. Several pilot solutions are presented and compared with the official solution to demonstrate influences of different approaches (e.g. definition of weights and the constraint) on results of the adjustment. In case of the official solution, all the gravimeters are in equivalence with declared uncertainties. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: Final report on CCQM-K9.2: Subsequent key comparison on pH determination of phosphate buffer by Harned cell measurements

NASA Astrophysics Data System (ADS)

Spitzer, Petra; Giera, Janine; Fraga, Isabel C.; Tønnes Jakobsen, Pia; Jensen, Hans D.; Hyllested, Peter; Karpov, Oleg; Kutovoy, Viatcheslav; Nakamura, Susumu; Vospelova, Alena; Zvezdina, Valentina

2008-01-01

CCQM-K9.2 was performed supplementary to the key comparison CCQM-K9 on the pH determination of a phosphate buffer with nominal pH ~ 6.9 (at 25 °C). The sample composition was very similar in both comparisons. Only the source of the starting material used for sample preparation was different. The comparison was restricted to the use of the primary method for pH (Harned cell measurement) as defined in the IUPAC Recommendations [2]. The measurement temperatures were 15 °C, 25 °C, 37 °C. CCQM-K9.2, CCQM-K.9 and the first supplementary comparison CCQM-K9.1 [5] are activities of the Electrochemical Working Group (EAWG) of the CCQM. All three comparisons were coordinated by the PTB, Germany. The Danish Primary Laboratory (DPL) successfully took part in the CCQM-K9. Meanwhile the primary set-up for pH in Denmark moved from DPL affiliated to Radiometer Medical to DFM, Denmark. The subsequent comparison allows assessing the degree of equivalence for the measurement of pH at DFM after the move. Due to the interest of other laboratories in demonstrating their progress in pH measurements on the primary level the CCQM-K9.2 supplementary comparison was extended to other participants than DFM, namely NMIJ, VNIIFTRI, INMETRO and CMI. The reported quantity for CCQM-K9.2 was not the pH of the sample but the acidity function at zero chloride molality (see chapter 12). To calculate the pH value from the acidity function it is necessary to know the ionic strength of the sample buffer solution, which was undisclosed by the coordinator. With the exception of the Czech Metrology Institute, CMI, good agreement in the determined acidity function is found between the participants. The results reported by DFM and by PTB agree within their measurement uncertainty at all measurement temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report

KEY COMPARISON: Report of the spectral irradiance comparison EURAMET.PR-K1.a.1 between MIKES (Finland) and NIMT (Thailand)

NASA Astrophysics Data System (ADS)

Ojanen, M.; Shpak, M.; Kärhä, P.; Leecharoen, R.; Ikonen, E.

2009-01-01

A bilateral comparison of the spectral irradiance scales between MIKES (Finland) and NIMT (Thailand) was carried out at 22 wavelengths between 290 nm and 900 nm. MIKES acted as the pilot and link to the results of the key comparison CCPR-K1.a. The spectral irradiance values measured by NIMT generally agree with the key comparison reference value within the expanded uncertainty. The only exceptions are results at wavelengths 300 nm, 450 nm and 500 nm, where the ratios between the degree of equivalence (DoE) and the expanded uncertainty of DoE (k = 2) are 1.0, 1.4 and 1.2, respectively. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report of the key comparison APMP.QM-K91: APMP comparison on pH measurement of phthalate buffer

NASA Astrophysics Data System (ADS)

Hioki, Akiharu; Asakai, Toshiaki; Maksimov, Igor; Suzuki, Toshihiro; Miura, Tsutomu; Ketrin, Rosi; Nuryatini; Thanh, Ngo Huy; Truong Chinh, Nguyen; Vospelova, Alena; Bastkowski, Frank; Sander, Beatrice; Matzke, Jessica; Prokunin, Sergey; Frolov, Dmitry; Aprelev, Alexey; Dobrovolskiy, Vladimir; Uysal, Emrah; Liv, Lokman; Velina Lara-Manzano, Judith; Montero-Ruiz, Jazmin; Ortiz-Aparicio, JosÉ Luis; Ticona Canaza, Galia; Anuar Mohd Amin, Khirul; Abd Kadir, Haslina; Bakovets, Nickolay; Wong, Siu-Kay; Lam, Wai-Hing

2017-01-01

The APMP.QM-K91 was organised by TCQM of APMP to test the abilities of the national metrology institutes in the APMP region to measure a pH value of a phthalate buffer. This APMP comparison on pH measurement was proposed by the National Metrology Institute of Japan at the APMP-TCQM meeting held September 22-23, 2014. After approval by TCQM, the comparison has been conducted by NMIJ. The comparison is a key comparison following CCQM-K91. The comparison material was a phthalate buffer of pH around 4.0 and the measurement temperatures were 15 °C, 25 °C and 37 °C. This is the third APMP key comparison on pH measurement and the fifth APMP comparison on pH measurement following APMP.QM-P06 (two phosphate buffers) in 2004, APMP.QM-P09 (a phthalate buffer) in 2006, APMP.QM-K9/APMP.QM-P16 (a phosphate buffer) in 2010-2011 and APMP.QM-K19/APMP.QM-P25 (a borate buffer) in 2013-2014. The results can be used further by any participant to support its CMC claim at least for a phthalate buffer. That claim will concern the pH method employed by the participant during this comparison and will cover the used temperature(s) or the full temperature range between 15°C and 37 °C for the participant which measured pH values at the three temperatures. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report of the key comparison APMP.QM-K9: APMP comparison on pH measurement of phosphate buffer

NASA Astrophysics Data System (ADS)

Hioki, Akiharu; Ohata, Masaki; Cherdchu, Chainarong; Tangpaisarnkul, Nongluck

2011-01-01

The APMP.QM-K9 was organised by TCQM of APMP to test the abilities of the national metrology institutes in the APMP region to measure a pH value of a phosphate buffer. This APMP comparison on pH measurement was proposed by the National Metrology Institute of Japan, NMIJ, and the National Institute of Metrology of Thailand, NIMT, in August 2009. After approval by TCQM, the comparison has been conducted by NMIJ and NIMT. The comparison is a key comparison following CCQM-K9, CCQM-K9.1 and CCQM-K9.2. The comparison material was a phosphate buffer of pH around 6.86 and the measurement temperatures were 15 °C, 25 °C and 37 °C. This is the first APMP key comparison on pH measurement and the third APMP comparison on pH measurement following APMP.QM-P06 (two phosphate buffers) in 2004 and APMP.QM-P09 (a phthalate buffer) in 2006. The results can be used further by any participant to support its CMC claim for a phosphate buffer. That claim will concern the pH method employed by the participant during this comparison and will cover the temperature(s) used or the full temperature range between 15 °C and 37 °C for the participant which measured pH values at the three temperatures. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Notification: FY 2017 Update of Proposed Key Management Challenges and Internal Control Weaknesses Confronting the U.S. Chemical Safety and Hazard Investigation Board

EPA Pesticide Factsheets

Jan 5, 2017. The EPA OIG is beginning work to update for fiscal year 2017 its list of proposed key management challenges and internal control weaknesses confronting the U.S. Chemical Safety and Hazard Investigation Board (CSB).

KEY COMPARISON: Final report of the SIM 60Co air-kerma comparison SIM.RI(I)-K1

NASA Astrophysics Data System (ADS)

Ross, C. K.; Shortt, K. R.; Saravi, M.; Meghzifene, A.; Tovar, V. M.; Barbosa, R. A.; da Silva, C. N.; Carrizales, L.; Seltzer, S. M.

2008-01-01

Transfer chambers were used to compare the standards for 60Co air kerma maintained by seven laboratories. Six of the laboratories are members of the Sistema Interamericano de Metrología (SIM) regional metrology organization while the seventh is the International Atomic Energy Agency (IAEA) laboratory in Vienna. The National Research Council (NRC) acted as the pilot laboratory for the comparison. Because of the participation of laboratories holding primary standards, the comparison results could be linked to the key comparison reference value maintained by the Bureau International des Poids et Mesures (BIPM). The results for all laboratories were within the expanded uncertainty (two standard deviations) of the reference value. The estimated relative standard uncertainty of the comparison between any pair of laboratories ranged from 0.5% to 1.0%. The largest discrepancy between any two laboratories was 1.0%. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI Section I, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON: Final report of comparison of the calibrations of hydrometers for liquid density determination between SIM laboratories: SIM.M.D-K4

NASA Astrophysics Data System (ADS)

Becerra, Luis Omar

2009-01-01

This SIM comparison on the calibration of high accuracy hydrometers was carried out within fourteen laboratories in the density range from 600 kg/m3 to 1300 kg/m3 in order to evaluate the degree of equivalence among participant laboratories. This key comparison anticipates the planned key comparison CCM.D-K4, and is intended to be linked with CCM.D-K4 when results are available. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Comparison of international guideline programs to evaluate and update the Dutch program for clinical guideline development in physical therapy.

PubMed

Van der Wees, Philip J; Hendriks, Erik J M; Custers, Jan W H; Burgers, Jako S; Dekker, Joost; de Bie, Rob A

2007-11-23

Clinical guidelines are considered important instruments to improve quality in health care. Since 1998 the Royal Dutch Society for Physical Therapy (KNGF) produced evidence-based clinical guidelines, based on a standardized program. New developments in the field of guideline research raised the need to evaluate and update the KNGF guideline program. Purpose of this study is to compare different guideline development programs and review the KNGF guideline program for physical therapy in the Netherlands, in order to update the program. Six international guideline development programs were selected, and the 23 criteria of the AGREE Instrument were used to evaluate the guideline programs. Information about the programs was retrieved from published handbooks of the organizations. Also, the Dutch program for guideline development in physical therapy was evaluated using the AGREE criteria. Further comparison the six guideline programs was carried out using the following elements of the guideline development processes: Structure and organization; Preparation and initiation; Development; Validation; Dissemination and implementation; Evaluation and update. Compliance with the AGREE criteria of the guideline programs was high. Four programs addressed 22 AGREE criteria, and two programs addressed 20 AGREE criteria. The previous Dutch program for guideline development in physical therapy lacked in compliance with the AGREE criteria, meeting only 13 criteria. Further comparison showed that all guideline programs perform systematic literature searches to identify the available evidence. Recommendations are formulated and graded, based on evidence and other relevant factors. It is not clear how decisions in the development process are made. In particular, the process of translating evidence into practice recommendations can be improved. As a result of international developments and consensus, the described processes for developing clinical practice guidelines have much in common

CCQM-K103 key comparison melanine in milk powder

NASA Astrophysics Data System (ADS)

Li, Xiuqin; Zhang, Qinghe; Li, Hongmei; Li, Mengwan; Wong, Siu-kay; Lee, Foo-Wing; Kakoulides, Elias; Naujaus, Evaldas; Fernandes-Whaley, Maria; Prevoo-Franzsen, Des; Quinn, Laura; Pookrod, Preeyaporn; Konopelko, Leonid

2017-01-01

Under the Comité Consultatif pour la Quantité de Matière (CCQM), a key comparison, CCQM-K103, was coordinated by the National Institute of Metrology (NIM) and Government Laboratory, Hong Kong, China (GLHK). The comparison was designed to demonstrate NMIs/DIs ability to analyze traces of melamine in milk and milk powder at concentration levels resulting from requirements for food safety. Seven NMIs or DIs participated in the comparison. Final reference value (KCRV) is 0.286 mg/kg, with standard uncertainty of the median as 0.011 mg/kg (3.8 %). The k-factor for the estimation of the expanded uncertainty was chosen as k = 2.57 ( t (0.05;5) ), thus the expanded uncertainty is 0.028 mg/kg (9.8%). The degrees of equivalence with melamine in milk powder KCRV for each participant were reported. The measurement results and degrees of equivalence should be indicative of the performance of a laboratory's measurement capability for IDMS in determining mass fractions in the range from 0.1 to 5.0 mg/kg of analytes with low molar mass (range 50-300 Da) with high polarity (pKow > -2.0) in milk and milk products. Extension to other analytes and matrices should be applied with care since there is a close linkage to other relevant parameters as e.g. sample preparation procedures (liquid/liquid extraction, SPE clean-up) and analytical separation techniques (e.g., GC-MS, LC-MS/MS etc). Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral key comparison on luminous flux COOMET.PR-K4.1. final report

NASA Astrophysics Data System (ADS)

Huriev, M.; Khlevnoy, B.; Tolstykh, G.; Ivashin, E.; Gorchkova, T.

2017-01-01

This report describes an international bilateral key comparison on luminous flux of tungsten lamps between the National Scientific Centre 'Institute of Metrology' (NSC 'IM', Ukraine) and All-Russian Research Institute for Optical and Physical Measurements (VNIIOFI, Russia). The comparison is intended to determine the Degrees of Equivalence (DoE) for NSC 'IM' and the associated expanded uncertainty. VNIIOFI acts as a laboratory, providing the link to the comparison CCPR-K4. The comparison used a set of tungsten incandescent lamps as a transfer standard with a luminous flux of approximately 3800 lm. The determined DoE of NSC 'IM' is -0.94% with an expanded uncertainty (k = 2) of 1.05%. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Leptanilla hypodracos sp. n., a new species of the cryptic ant genus Leptanilla (Hymenoptera, Formicidae) from Singapore, with new distribution data and an updated key to Oriental Leptanilla species

PubMed Central

Wong, Mark K. L.; Guénard, Benoit

2016-01-01

Abstract A new species of the cryptic and rarely collected ant genus Leptanilla is described. Leptanilla hypodracos sp. n. is the first Leptanilla recorded from Singapore in over a century since Leptanilla havilandi Forel, 1901 and represents the fourth species of Leptanilla known from the Malay Peninsula. An updated key to the Leptanilla of the Oriental region is presented. Taxonomic comparisons between Leptanilla hypodracos sp. n. and four morphologically similar species are provided with particular attention given to Leptanilla clypeata Yamane & Ito, 2001, for which new measurements and indices are presented. The first report is presented for the Leptanillinae subfamily from the southeastern part of China with a worker of the genus Leptanilla collected in Hong Kong. Finally, the potential of subterranean bait to collect Leptanilla species is discussed. PMID:26877667

KEY COMPARISON: Final Report on CCT-K7: Key comparison of water triple point cells

NASA Astrophysics Data System (ADS)

Stock, M.; Solve, S.; del Campo, D.; Chimenti, V.; Méndez-Lango, E.; Liedberg, H.; Steur, P. P. M.; Marcarino, P.; Dematteis, R.; Filipe, E.; Lobo, I.; Kang, K. H.; Gam, K. S.; Kim, Y.-G.; Renaot, E.; Bonnier, G.; Valin, M.; White, R.; Dransfield, T. D.; Duan, Y.; Xiaoke, Y.; Strouse, G.; Ballico, M.; Sukkar, D.; Arai, M.; Mans, A.; de Groot, M.; Kerkhof, O.; Rusby, R.; Gray, J.; Head, D.; Hill, K.; Tegeler, E.; Noatsch, U.; Duris, S.; Kho, H. Y.; Ugur, S.; Pokhodun, A.; Gerasimov, S. F.

2006-01-01

accepted this recommendation and the next edition of the SI brochure will include this specification. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Description of third instars of Cochliomyia minima (Diptera: Calliphoridae) from West Indies, and updated identification key.

PubMed

Yusseff-Vanegas, S

2014-09-01

The blow fly Cochliomyia minima Shannon is endemic to the Caribbean, and it has great potential for forensic applications because of its abundance and broad distribution in the region. However, its larval stages are unknown. Here, I update previously published identification keys by describing for the first time the morphology of C. minima larvae. The larvae of C. minima are found to be very similar to those of Cochliomyia macellaria F., but the former can be easily identified by the oral sclerite completely pigmented, visible as a spike between mouth hooks. The description of C. minima larvae in this study will be useful to forensic scientists in the Caribbean region.

Comparison of international guideline programs to evaluate and update the Dutch program for clinical guideline development in physical therapy

PubMed Central

Van der Wees, Philip J; Hendriks, Erik JM; Custers, Jan WH; Burgers, Jako S; Dekker, Joost; de Bie, Rob A

2007-01-01

Background Clinical guidelines are considered important instruments to improve quality in health care. Since 1998 the Royal Dutch Society for Physical Therapy (KNGF) produced evidence-based clinical guidelines, based on a standardized program. New developments in the field of guideline research raised the need to evaluate and update the KNGF guideline program. Purpose of this study is to compare different guideline development programs and review the KNGF guideline program for physical therapy in the Netherlands, in order to update the program. Method Six international guideline development programs were selected, and the 23 criteria of the AGREE Instrument were used to evaluate the guideline programs. Information about the programs was retrieved from published handbooks of the organizations. Also, the Dutch program for guideline development in physical therapy was evaluated using the AGREE criteria. Further comparison the six guideline programs was carried out using the following elements of the guideline development processes: Structure and organization; Preparation and initiation; Development; Validation; Dissemination and implementation; Evaluation and update. Results Compliance with the AGREE criteria of the guideline programs was high. Four programs addressed 22 AGREE criteria, and two programs addressed 20 AGREE criteria. The previous Dutch program for guideline development in physical therapy lacked in compliance with the AGREE criteria, meeting only 13 criteria. Further comparison showed that all guideline programs perform systematic literature searches to identify the available evidence. Recommendations are formulated and graded, based on evidence and other relevant factors. It is not clear how decisions in the development process are made. In particular, the process of translating evidence into practice recommendations can be improved. Conclusion As a result of international developments and consensus, the described processes for developing clinical

Linking results of key and supplementary comparisons of AC/DC voltage transfer references

NASA Astrophysics Data System (ADS)

Velychko, Oleh

2018-04-01

A regional key comparison (KC) COOMET.EM-K6.a and a supplementary comparison (SC) COOMET.EM-S1 of AC/DC voltage transfer references were conducted between participating laboratories from the Eurasian region. Measurements were made over the period 2004-2014. The results showed good agreement between all but one of the participating laboratories. The proposed procedure of linking results of key and SCs of regional metrology organization of AC/DC voltage transfer references is presented. Linking results is realized for COOMET.EM-K6.a and CCEM-K6.a KCs, and for COOMET.EM-K6.a KC and COOMET.EM-S1 SC.

EURAMET.T-K7 Key Comparison of Water Triple-Point Cells

NASA Astrophysics Data System (ADS)

Peruzzi, A.; Bosma, R.; Kerkhof, O.; Rosenkranz, P.; Del Campo Maldonado, M. D.; Strnad, R.; Nielsen, J.; Anagnostou, M.; Veliki, T.; Zvizdic, D.; Grudnewicz, E.; Nedea, M.; Neagu, D. M.; Steur, P.; Filipe, E.; Lobo, I.; Antonsen, I.; Renaot, E.; Heinonen, M.; Weckstrom, T.; Bojkovski, J.; Turzo-Andras, E.; Nemeth, S.; White, M.; Tegeler, E.; Dobre, M.; Duris, S.; Kartal Dogan, A.; Uytun, A.; Augevicius, V.; Pauzha, A.; Pokhodun, A.; Simic, S.

2011-12-01

The results of a EURAMET key comparison of water triple-point cells (EURAMET.T-K7) are reported. The equipment used, the measuring conditions applied, and the procedures adopted for the water triple-point measurement at the participating laboratories are synthetically presented. The definitions of the national reference for the water triple-point temperature adopted by each laboratory are disclosed. The multiplicity of degrees of equivalence arising for the linking laboratories with respect to the "mother" comparison CCT-K7 is discussed in detail.

KEY COMPARISON: Final report of the SIM 60Co absorbed-dose-to-water comparison SIM.RI(I)-K4

NASA Astrophysics Data System (ADS)

Ross, C. K.; Shortt, K. R.; Saravi, M.; Meghzifene, A.; Tovar, V. M.; Barbosa, R. A.; da Silva, C. N.; Carrizales, L.; Seltzer, S. M.

2008-01-01

Transfer chambers were used to compare the standards for 60Co absorbed dose to water maintained by seven laboratories. Six of the laboratories were members of the Sistema Interamericano de Metrología (SIM) regional metrology organization while the seventh was the International Atomic Energy Agency (IAEA) laboratory in Vienna. The National Research Council (NRC) acted as the pilot laboratory for the comparison. Because of the participation of laboratories holding primary standards, the comparison results could be linked to the key comparison reference value maintained by the Bureau International des Poids et Mesures (BIPM). The results for all laboratories were within the expanded uncertainty (two standard deviations) of the reference value. The estimated relative standard uncertainty on the comparison between any pair of laboratories ranged from 0.6% to 1.4%. The largest discrepancy between any two laboratories was 1.3%. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI Section I, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report on key comparison CCQM-K100: Analysis of copper in ethanol

NASA Astrophysics Data System (ADS)

Zhou, Tao; Kakoulides, Elias; Zhu, Yanbei; Jaehrling, Reinhard; Rienitz, Olaf; Saxby, David; Phukphatthanachai, Pranee; Yafa, Charun; Labarraque, Guillaume; Cankur, Oktay; Can, Süleyman Z.; Konopelko, Leonid A.; Kustikov, Yu A.; Caciano de Sena, Rodrigo; Marques Rodrigues, Janaina; Fonseca Sarmanho, Gabriel; Fortunato de Carvalho Rocha, Werickson; dos Reis, Lindomar Augusto

2014-01-01

The increase in renewable sources in the energy matrix of the countries is an effort to reduce dependency on crude oil and the environmental impacts associated with its use. In order to help overcome the lack of widely accepted quality standards for fuel ethanol and to guarantee its competitiveness in the international trade market, the NMIs have been working to develop certified reference materials for bio-fuels and measurement methods. Inorganic impurities such as Cu, Na and Fe may be present in the fuel ethanol and their presence is associated with corrosion and the formation of oxide deposits in some engine parts. The key comparison CCQM-K100 was carried out under the auspices of the Inorganic Analysis Working Group (IAWG) and the coordination of the National Institute of Metrology, Quality and Technology (INMETRO). The objective of this key comparison was to compare the measurement capabilities of the participants for the determination of Cu in fuel ethanol. Ten NMIs participated in this exercise and most of them used the isotopic dilution method for determining the amount of Cu. The median was chosen as key comparison reference value (KCRV). The assigned KCRV for the Cu content was 0.3589 µg/g with a combined standard uncertainty of 0.0014 µg/g. In general, there is a good agreement among the participants' results. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: CCQM-K25: Determination of PCB congeners in sediment

NASA Astrophysics Data System (ADS)

Schantz, Michele; Wise, Stephen

2004-01-01

Polychlorinated biphenyls (PCBs) consist of 209 possible congeners depending on the substitution of the chlorine atoms around the biphenyl molecule. PCBs have been widely used as industrial fluids, flame retardants, diluents, hydraulic fluids, and dielectric fluids for capacitors and transformers. As a class of compounds, they are environmentally stable and tend to bioaccumulate. Of the 209 possible congeners, approximately 150 congeners have been reported in the environment. Congener-specific PCB methods, which are typically based on gas chromatography (GC) with electron capture detection (ECD) or mass spectrometric (MS) detection, are designed to measure selected priority congeners, but the congeners of interest change with the study and sponsoring agency. A pilot study (CCQM-P17) for the determination of PCB congeners in sediment was organized by NIST and NRC-Canada in 2000. Ten laboratories participated in the pilot study. After discussion and critical review of the data, there was agreement that the pilot study should be followed by a Key Comparison and that the Key Comparison Reference Value (KCRV) should be derived from isotope dilution GC/MS (ID-GC/MS) based methods that had been validated in the Pilot Study. The CCQM-K25 Key Comparison study utilized a sediment sample prepared by mixing known quantities of two sediment materials to simulate a moderately contaminated sample with respect to PCBs. Nine laboratories participated in CCQM-K25 and demonstrated a high level of equivalence in capabilities for determining five PCB congeners (congener numbers 28, 101, 105, 153, and 170) in a moderately contaminated sediment using GC/MS-based methods. The amount of substance concentration for the congeners measured ranged from ~10 ng/g to ~35 ng/g. The relative expanded uncertainties of the KCRVs ranged from 2% to 5%, indicating excellent agreement among the participants that used ID-GC/MS. Results from the one laboratory that used GC/MS with a non-labeled PCB

Final report on key comparison CCQM-K81: Chloramphenicol in pig muscle

NASA Astrophysics Data System (ADS)

Polzer, Joachim; Henrion, Andre; Gowik, Petra

2013-01-01

Under the auspices of the Organic Analysis Working Group (OAWG) of the Comité Consultatif pour la Quantité de Matière (CCQM) a key comparison, CCQM-K81 'Chloramphenicol in pig muscle', was coordinated by BVL and PTB in 2009/2010. Six NMIs/DIs participated in this comparison. Chloramphenicol (CAP) is an effective broad-spectrum antibiotic which can in principle be used for the treatment of humans and animals. Its use for the treatment of food-producing animals is, however, forbidden worldwide in many countries due to potential severe side effects. The key comparison was the follow-up to the successful pilot study 'CCQM-P90: chloramphenicol in milk'. With this key comparison it was intended to demonstrate the capability of NMIs/DIs to analyse traces of CAP in food at concentration levels resulting from legal requirements for food control. Additionally, the quality of this kind of analysis with respect to compliance with legal requirements for food control methods and the international comparability of measurements should be evaluated in general. The study was classified as a 'track C' study (studies in emerging areas of global interest). For the study incurred lyophilised pig muscle material containing CAP (at a mass-fraction level around the maximum allowable level for import for a number of countries) has been produced as a candidate reference material by BVL and IRMM (Institute for Reference Materials and Measurements, JRC of the European Commission). Animal treatment and slaughtering of the animal to gain incurred muscle material as well as pre-testing of the CAP content was done at the BVL. The IRMM did further processing of the material and testing of homogeneity and stability. Participants were invited to assign the mass fraction of free CAP in the comparison sample. CCQM-K81 demonstrated successfully the capability of the participating laboratories to assign chloramphenicol values in tissue down to residue levels of around 0.3 ng/g (referring to the

CCQM key comparison CCQM-K75: Determination of toxic metals in algae

NASA Astrophysics Data System (ADS)

Shakhashiro, A.; Toervenyi, A.; Gaudino, S.; Rosamilia, S.; Belli, M.; Turk, G. C.

2011-01-01

The determination of mass fraction of toxic elements and especially platinum emitted from automobile catalytic converters in the air is a critical factor in assessing air quality and the potential impact of possible pollutants. Air is in fact one of the main pathways for human exposure to toxic elements. Biomonitors, such as lichen and algae, are examples of environmental samples that have been widely used by the scientific community to assess and monitor the level of environmental pollution. For this purpose, the IAEA-450 algae material containing heavy metals and platinum at low level was prepared by IAEA Seibersdorf Laboratories in collaboration with the Italian National Institute for Environmental Protection—ISPRA (former APAT). During the April meeting in 2009 of the Inorganic Analysis Working Group (IAWG) of the CCQM it was agreed to organize a key comparison K75 for Pt and Ni and a parallel pilot study P118 for As, Cd, Cr, Hg, Ni, Pb and Pt using this algae material. The key comparison CCQM-K75 was successfully organized. The participating NMIs demonstrated a high level of measurement capabilities and technical competence in analysing nickel and platinum at a low level of concentration in environmental samples such as algae. The between-laboratories reproducibility standard deviation for nickel and platinum was 1.9% and 3.6% respectively, which reflects an excellent agreement of between-laboratories measurement results. The ratio between the bias and its expanded uncertainty for nickel and platinum was below 2.0 for all reported results except in one case. This study was a practical demonstration of a CCQM comparison to use the 'core-capabilities' utilized by participants as a mean of providing evidence for Calibration and Measurement Capabilities (CMC) claims for Ni and Pt. Based on this CCQM international key comparison, the measurement capability of the NMIs which participated in the CCQM-K75 has been demonstrated directly for determination of Pt and Ni

KEY COMPARISON: Report on the Regional Comparison COOMET.AUV.A-K3

NASA Astrophysics Data System (ADS)

Barrera-Figueroa, Salvador; Nielsen, Lars; Rasmussen, Knud

2007-01-01

COOMET.AUV.A-K3 is a Regional Comparison that supplements the Key Comparison CCAUV.A-K3 organized by the CCAUV. The participating NMIs are GUM (Poland), INM (Romania), VNIIFTRI (Russia) and DP-NDI 'Systema' (Ukraine). The role of Pilot laboratory was undertaken by DPLADFM (Denmark). The measurements took place between May 2005 and February 2006. The time schedule was organized in a single star configuration. Initially, two LS2aP microphones were circulated. However, a sudden change of sensitivity of one of them forced the inclusion of an additional microphone. Nevertheless, the analysis was performed on all microphones involved. This report includes the measurement results from the participants, information about their calibration methods, and the analysis leading to the assignation of degrees of equivalence and the link to the CCAUV.A-K3. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Three new species of Macrelmis Motschulsky, 1859 (Coleoptera: Elmidae: Elminae) from the Brazilian Cerrado Biome with updated key for the Macrelmis of Brazil.

PubMed

Barbosa, Felipe Francisco; Fernandes, André Silva; Oliveira, Leandro Gonçalves

2013-11-12

Three new species of Macrelmis Motschulsky, 1859 (Macrelmis bispo sp. nov., Macrelmis froehlichi sp. nov., and Macrelmis nessimiani sp. nov.) are herein described and illustrated. The species were collected from several streams in Goiás State, Brazil, a formerly unknown region concerning Elmidae fauna. We also provide an updated key for the Macrelmis species of Brazil.

KEY COMPARISON: Comparison of the standards for absorbed dose to water of the ENEA-INMRI (Italy) and the BIPM for 60Co γ rays

NASA Astrophysics Data System (ADS)

Kessler, C.; Allisy-Roberts, P. J.; Burns, D. T.; Guerra, A. S.; Laitano, R. F.; Pimpinella, M.

2010-01-01

A comparison of the standards for absorbed dose to water of the Istituto Nazionale di Metrologia delle Radiazioni Ionizzanti of the Ente per le Nuove Tecnologie, l'Energia e l'Ambiente, Italy (ENEA-INMRI), and of the Bureau International des Poids et Mesures (BIPM) has been made in 60Co gamma radiation under the auspices of the key comparison BIPM.RI(I)-K4. The comparison result, based on the calibration coefficients for three transfer standards and expressed as a ratio of the ENEA and the BIPM standards for absorbed dose to water, is 0.9999 (0.0044). The present 2007 result replaces the earlier ENEA value in this key comparison. The degrees of equivalence between the ENEA and the other participants in this comparison have been calculated and the results are given in the form of a matrix for the ten national metrology institutes (NMIs) that have published results in this ongoing comparison for absorbed dose to water. A graphical presentation is also given. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI Section I, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Key comparison CCPR-K1.a as an interlaboratory comparison of correlated color temperature

NASA Astrophysics Data System (ADS)

Kärhä, P.; Vaskuri, A.; Pulli, T.; Ikonen, E.

2018-02-01

We analyze the results of spectral irradiance key comparison CCPR-K1.a for correlated color temperature (CCT). For four participants out of 13, the uncertainties of CCT, calculated using traditional methods, not accounting for correlations, would be too small. The reason for the failure of traditional uncertainty calculation is spectral correlations, producing systematic deviations of the same sign over certain wavelength regions. The results highlight the importance of accounting for such correlations when calculating uncertainties of spectrally integrated quantities.

7. Mentor update and support: what do mentors need from an update?

PubMed

Phillips, Mari; Marshall, Joyce

2015-04-01

Mentorship is the 14th series of 'Midwifery basics' targeted at practising midwives. The aim of these articles is to provide information to raise awareness of the impact of the work of midwives on women's experience, and encourage midwives to seek further information through a series of activities relating to the topic. In this seventh article Mari Phillips and Joyce Marshall consider some of the key issues related to mentor update and support and consider what mentors need from their annual update.

Final report on EUROMET key comparison EUROMET.M.D-K2 (EUROMET 627) "Comparison of density determinations of liquid samples"

NASA Astrophysics Data System (ADS)

Bettin, Horst; Heinonen, Martti; Gosset, André; Zelenka, Zoltán; Lorefice, Salvatore; Hellerud, Kristen; Durlik, Hanna; Jordaan, Werner; Field, Ireen

2016-01-01

The results of the key comparison EUROMET 627 (EUROMET.M.D-K2) are presented. This project covered the density measurements of three liquids: dodecane, water and an oil of high viscosity measured at 15 °C, 20 °C and 40 °C. Seven European metrology laboratories and the South African laboratory CSIR-NML (now: NMISA) measured the densities at atmospheric pressure by hydrostatic weighing of solid density standards between 04 October 2001 and 18 December 2001. The stability and homogeneity of the liquids were investigated by the pilot laboratory PTB. The results generally show good agreement among the participants. Only for the simple Mohr-Westphal balances do the uncertainties seem to be underestimated by the laboratories. Furthermore, the measurement of high-viscosity oil was difficult for some laboratories. Nevertheless, the five laboratories PTB/DE, BNM/FR (now: LNE/FR), OMH/HU (now: MKEH/HU), IMGC/IT (now: INRIM/IT) and GUM/PL agree with each other for stated uncertainties of 0.05 kg/m3 or less. This satisfies the current needs of customers who wish to calibrate or check liquid density measuring instruments such as oscillation-type density meters. No reference values were calculated since the subsequent CCM key comparison CCM.D-K2 had a different scope and the EUROMET 627 comparison was soon superseded by the EURAMET 1019 (EURAMET.M.D-K2) comparison. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on COOMET Vickers PTB/VNIIFTRI key comparison (COOMET.M.H-K1.b and COOMET.M.H-K1.c)

NASA Astrophysics Data System (ADS)

Aslanyan, E.; Herrmann, K.

2013-01-01

This report describes a COOMET key comparison on Vickers hardness scales of two National Metrology Institutes—PTB and VNIIFTRI. The pilot laboratory was PTB, which was the linking institute with the key comparison reference values of CCM.H-K1. In the key comparison two sets of hardness reference blocks for the Vickers hardness scales HV1 and HV30, each consisting of three hardness reference blocks with the hardness levels 240 HV, 540 HV and 840 HV, are used. The same hardness reference blocks were used previously in the key comparison CCM.H-K1. The measurement results and uncertainty assessments, announced by VNIIFTRI, are in good agreement with the key comparison reference values of CCM.H-K1. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Key on demand (KoD) for software-defined optical networks secured by quantum key distribution (QKD).

PubMed

Cao, Yuan; Zhao, Yongli; Colman-Meixner, Carlos; Yu, Xiaosong; Zhang, Jie

2017-10-30

Software-defined optical networking (SDON) will become the next generation optical network architecture. However, the optical layer and control layer of SDON are vulnerable to cyberattacks. While, data encryption is an effective method to minimize the negative effects of cyberattacks, secure key interchange is its major challenge which can be addressed by the quantum key distribution (QKD) technique. Hence, in this paper we discuss the integration of QKD with WDM optical networks to secure the SDON architecture by introducing a novel key on demand (KoD) scheme which is enabled by a novel routing, wavelength and key assignment (RWKA) algorithm. The QKD over SDON with KoD model follows two steps to provide security: i) quantum key pools (QKPs) construction for securing the control channels (CChs) and data channels (DChs); ii) the KoD scheme uses RWKA algorithm to allocate and update secret keys for different security requirements. To test our model, we define a security probability index which measures the security gain in CChs and DChs. Simulation results indicate that the security performance of CChs and DChs can be enhanced by provisioning sufficient secret keys in QKPs and performing key-updating considering potential cyberattacks. Also, KoD is beneficial to achieve a positive balance between security requirements and key resource usage.

Bilateral comparison of 1 Ω standards (ongoing BIPM key comparison BIPM.EM-K13.a) between the NSAI-NML (Ireland) and the BIPM

NASA Astrophysics Data System (ADS)

Goebel, R.; Power, O.; Fletcher, N.; Stock, M.

2012-01-01

This report describes the results obtained from a NML(Ireland)-BIPM bilateral comparison of 1 Ω resistance standards in 2010. The comparison was carried out in the framework of the BIPM ongoing key comparison BIPM.EM-K13.a. Two BIPM 1 Ω travelling standards of CSIRO type were calibrated first at the BIPM, then at the NMLI and again at the BIPM after their return. The stability of the transfer standard was such that the uncertainty associated with the transfer was significantly smaller than the uncertainty arising from the calibrations. The mean difference between the NMLI and the BIPM calibrations was found to be just within the expanded uncertainty (k = 2) of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report on key comparison COOMET.QM-K36 (Project COOMET 540/UA/11) 'Electrolytic Conductivity 0,5 S/m'

NASA Astrophysics Data System (ADS)

Gavrilkin, V.; Prokopenko, L.; Bakovec, N.; Zolotorevich, E.; Suvorov, V.; Ovchinnikov, Yu; Pilishvili, T.; Buleishvili, M.; Zhasanbaeva, B.; Aytzhatova, G.; Ticona, G.; Vyskocil, L.

2015-01-01

The COOMET.QM-K36 key comparison 'Electrolytic conductivity: 0.5 S/m' is a comparison in the field of electrolytic conductivity measurements conducted by COOMET and carried out in 2012. It used a solution of KCl in water and the results are connected to those of the CCQM key comparison CCQM-K36.a through common participation of VNIIFTRI (Russia), SMU (Slovakia) and Ukrmetrteststandart (Ukraine). The purpose of this key comparison was to establish the equivalence of measurements of electrolytic conductivity performed at the National Metrology Institutes of COOMET member states for the value of 0.5 S/m. The results can be used to support the CMCs claims over the range of 0.1 S/m to 1.3 S/m. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Consensus building for interlaboratory studies, key comparisons, and meta-analysis

NASA Astrophysics Data System (ADS)

Koepke, Amanda; Lafarge, Thomas; Possolo, Antonio; Toman, Blaza

2017-06-01

Interlaboratory studies in measurement science, including key comparisons, and meta-analyses in several fields, including medicine, serve to intercompare measurement results obtained independently, and typically produce a consensus value for the common measurand that blends the values measured by the participants. Since interlaboratory studies and meta-analyses reveal and quantify differences between measured values, regardless of the underlying causes for such differences, they also provide so-called ‘top-down’ evaluations of measurement uncertainty. Measured values are often substantially over-dispersed by comparison with their individual, stated uncertainties, thus suggesting the existence of yet unrecognized sources of uncertainty (dark uncertainty). We contrast two different approaches to take dark uncertainty into account both in the computation of consensus values and in the evaluation of the associated uncertainty, which have traditionally been preferred by different scientific communities. One inflates the stated uncertainties by a multiplicative factor. The other adds laboratory-specific ‘effects’ to the value of the measurand. After distinguishing what we call recipe-based and model-based approaches to data reductions in interlaboratory studies, we state six guiding principles that should inform such reductions. These principles favor model-based approaches that expose and facilitate the critical assessment of validating assumptions, and give preeminence to substantive criteria to determine which measurement results to include, and which to exclude, as opposed to purely statistical considerations, and also how to weigh them. Following an overview of maximum likelihood methods, three general purpose procedures for data reduction are described in detail, including explanations of how the consensus value and degrees of equivalence are computed, and the associated uncertainty evaluated: the DerSimonian-Laird procedure; a hierarchical Bayesian

Final report on CIPM key comparison CCM.FF-K6.2011: Comparison of the primary (national) standards of low-pressure gas flow

NASA Astrophysics Data System (ADS)

Benková, Miroslava; Makovnik, Stefan; Mickan, Bodo; Arias, Roberto; Chahine, Khaled; Funaki, Tatsuya; Li, Chunhui; Choi, Hae Man; Seredyuk, Denys; Su, Chun-Min; Windenberg, Christophe; Wright, John

2014-01-01

The comparison CCM.FF-K6.2011 was organized for the purpose of determination of the degree of equivalence of the national standards for low-pressure gas flow measurement over the range (2 to 100) m3/h. A rotary gas meter was used as a transfer standard. The measurements were provided at prescribed reference conditions. Eleven laboratories from four RMOs participated in this key comparison—EURAMET: PTB, Germany; SMU, Slovakia; LNE-LADG, France; SIM: NIST, USA; CENAM, Mexico; APMP: NMIJ AIST Japan; KRISS, Korea; NMI, Australia; NIM, China; CMS, Chinese Taipei; COOMET: GP GP Ivano-Frankivs'kstandart-metrologia, Ukraine and all participants reported independent traceability chains to the SI. All results were used in the determination of the key comparison reference value (KCRV) and the uncertainty of the KCRV. The reference value was determined at each flow separately following procedure A presented by M G Cox. The degree of equivalence with the KCRV was also calculated for each flow and laboratory. All reported results were consistent with the KCRV. This KCRV can now be used in the further regional comparisons. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON Bilateral comparison of 1.018 V and 10 V standards between the NSAI-NML (Ireland) and the BIPM, March to April 2010 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Power, O.; Solve, S.; Chayramy, R.; Stock, M.

2010-01-01

As a part of the ongoing BIPM key comparisons BIPM.EM-K11.a and b, a comparison of the 1.018 V and 10 V voltage reference standards of the BIPM and of the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from March to April 2010. Two BIPM Zener diode-based travelling standards were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage is maintained at the 10 V level by means of a group of characterized Zener diode-based electronic voltage standards. The output EMF of each travelling standard, at the 10 V output terminals, was measured by direct comparison with the group standard. Measurements of the output EMF of the travelling standards at the 1.018 V output terminals were made using a potentiometer, standardized against the local 10 V reference standard. At the BIPM, the travelling standards were calibrated at both voltages before and after the measurements at NSAI-NML, using the BIPM Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient pressure. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Bilateral comparison of 10 kΩ standards (ongoing BIPM key comparison BIPM.EM-K13.b) between the NSAI-NML (Ireland) and the BIPM

NASA Astrophysics Data System (ADS)

Goebel, R.; Power, O.; Fletcher, N.; Stock, M.

2012-01-01

This report describes the results obtained from a NML(Ireland)-BIPM bilateral comparison of 10 kΩ resistance standards in 2010. The comparison was carried out in the framework of the BIPM ongoing key comparison BIPM.EM-K13.b. Two BIPM 10 kΩ travelling standards of SR104 type were calibrated first at the BIPM, then at the NMLI and again at the BIPM after their return. The stability of the transfer standards was such that the uncertainty associated with the transfer was significantly smaller than the uncertainty arising from the calibrations. The NMLI and the BIPM calibrations were found to be in agreement, with a mean difference smaller than the standard uncertainty of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON Final report on APMP.EM-K6.a: APMP international comparison of ac-dc transfer standards at the lowest attainable level of uncertainty

NASA Astrophysics Data System (ADS)

Budovsky, Ilya

2010-01-01

The APMP international comparison of ac-dc transfer standards at the lowest attainable level of uncertainty, APMP.EM-K6a, started in 2000 and concluded in 2003. This comparison has offered the same range and frequencies as the key comparison CCEM-K6a with the view of providing the National Metrology Institutes (NMIs) of the APMP member economies with an opportunity to link the values of their standards for ac-dc transfer difference to the international reference values. The ac-dc difference of the travelling standard was measured with 3 V applied at standard frequencies of 1 kHz, 20 kHz, 100 kHz and 1 MHz, and optional frequencies of 50 kHz and 500 kHz. The travelling standard has not been damaged and has shown excellent stability. The results submitted by the overwhelming majority of the participants lie well within the reported uncertainty. At the standard frequencies the results have been linked to those of the CCEM-K6a key comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report on APMP.T-K7 key comparison of water triple point cells

NASA Astrophysics Data System (ADS)

Tsai, S. F.; White, R.; Tamba, J.; Yamazawa, K.; Ho, M. K.; Tsui, C. M.; Zaid, G.; Achmadi, A.; Gam, K. S.; Othman, H.; Ali, N. M.; Yuan, K. H.; Shaochun, Y.; Liedberg, H.; Yaokulbodee, C.

2016-01-01

APMP.T-K7, was held from February 2008 to September 2009 to compare the national realizations of the water triple point among eleven NMIs. To reach the objective, each participating laboratory sent a transfer cell to CMS and stated a value for the temperature difference of the transfer cell, relative to the corresponding national standard, representing 273.16 K. CMS (Taiwan) organized the comparison, with the support from co-pilot institutes MSL (New Zealand) and NMIJ (Japan). The other eight participating laboratories included NMIA, SCL, KIM-LIPI, KRISS, NMIM/SIRIM, NMC, NMISA, and NIMT. This report presents the results of the TPW comparison, gives detailed information about the measurements made at the CMS and at the participating laboratories, and aims to link the results of APMP.T-K7 to CCT-K7. The results of this key comparison are also represented in the form of degrees of equivalence for the purposes of the MRA. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: Final report on bilateral comparison CCEM.RF-K9.1: Thermal noise standards at 12.4 GHz, 13.5 GHz, 15 GHz and 17.5 GHz

NASA Astrophysics Data System (ADS)

Allal, Djamel

2009-01-01

A bilateral comparison subsequent to key comparison CCEM.RF-K9 was decided between VNIIFTRI and PTB. It was registered into the BIPM KCDB under the identifier CCEM.RF-K9.1. The results of this comparison were gathered by the pilot laboratory of comparison CCEM.RF-K9, the LNE, and a very good agreement was found between the two participants. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON: BIPM comparison BIPM.RI(II)-K1.Cu-64 of the activity measurements of the radionuclide 64Cu

NASA Astrophysics Data System (ADS)

Michotte, C.; Courte, S.; Ratel, G.; Kossert, K.; Nähle, O. J.

2009-01-01

In 2009, the Physikalisch-Technische Bundesanstalt (PTB), Germany, submitted a sample of known activity of 64Cu to the International Reference System (SIR) for activity comparison at the Bureau International des Poids et Mesures (BIPM). The value of the activity submitted was about 9.3 MBq. The result of this new comparison has been approved for publication by Section II of the Consultative Committee for Ionizing Radiation (CCRI(II)), comparison identifier BIPM.RI(II)-K1.Cu-64. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI Section II, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

European food-based dietary guidelines: a comparison and update.

PubMed

Montagnese, Concetta; Santarpia, Lidia; Buonifacio, Margherita; Nardelli, Arturo; Caldara, Anna Rita; Silvestri, Eufemia; Contaldo, Franco; Pasanisi, Fabrizio

2015-01-01

The aim of this study was to review and update information about food-based dietary guidelines (FBDGs) used by European countries. FBDGs from 34 European countries were collected and their pictorial representations, food groupings, and associated messages of healthy eating and behavior were compared. FBDGs from 34 European countries were collected, representing 64% (34 of 53) of all European countries; 74% (28 of 34) are European Union members. Of these FBDGs, 67% (23 of 34) adopt the pyramid as a food guide illustration, and classify foods into five or six groups. The main food groups are grains, vegetables, fruits, and vegetables and fruits as a unified group. Some differences include the modality of food classification. Despite dietary pattern results from geographic conditions and cultural (ethnic) heritages, most nutritional key points are similar among the different European FBDGs: In particular, the basic message is to consume adequate amounts of grains, vegetables, and fruits with moderate intake of fats, sugars, meats, caloric beverages, and salt. Other healthy behaviors are frequently but not always indicated. FBDGs still seem insufficient as far as ethnic peculiarities, agreement on how to group foods, and subgroup population nutritional requirements. Copyright © 2015 Elsevier Inc. All rights reserved.

A Probabilistic Approach to Model Update

NASA Technical Reports Server (NTRS)

Horta, Lucas G.; Reaves, Mercedes C.; Voracek, David F.

2001-01-01

Finite element models are often developed for load validation, structural certification, response predictions, and to study alternate design concepts. In rare occasions, models developed with a nominal set of parameters agree with experimental data without the need to update parameter values. Today, model updating is generally heuristic and often performed by a skilled analyst with in-depth understanding of the model assumptions. Parameter uncertainties play a key role in understanding the model update problem and therefore probabilistic analysis tools, developed for reliability and risk analysis, may be used to incorporate uncertainty in the analysis. In this work, probability analysis (PA) tools are used to aid the parameter update task using experimental data and some basic knowledge of potential error sources. Discussed here is the first application of PA tools to update parameters of a finite element model for a composite wing structure. Static deflection data at six locations are used to update five parameters. It is shown that while prediction of individual response values may not be matched identically, the system response is significantly improved with moderate changes in parameter values.

Results and evaluation of key comparison CCM.P-K12.1 for very low helium flow rates (leak rates)

NASA Astrophysics Data System (ADS)

Šetina, Janez; Vičar, Martin; Pražák, Dominik

2015-01-01

The Czech Metrology Institute (CMI) took part and failed to prove equivalence in the Key Comparison CCM.P-K12 of helium leak artefacts (leak rates) into vacuum. After identifying and eliminating the cause of the failure, the Institute of Metals and Technology (IMT) of Slovenia, a successful participant in CCM.P-K12, volunteered to serve as pilot and link in a following bilateral comparison of IMT and CMI that obtained designation CCM.P-K12.1 in June 2012. It was decided to perform the comparison with a glass permeation helium leak artefact at nominally 3.10-11 mol/s (7.4.10-7 mbar.L.s-1) at 23 °C. Both the laboratory standards took part in CCM.P-K12 and were considered as primary. The comparison measurements were performed in October 2012. CMI proved equivalence both with IMT and with the reference value of the key comparison CCM.P-K12. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Reporting Items for Updated Clinical Guidelines: Checklist for the Reporting of Updated Guidelines (CheckUp)

PubMed Central

Vernooij, Robin W. M.; Alonso-Coello, Pablo; Brouwers, Melissa

2017-01-01

Background Scientific knowledge is in constant development. Consequently, regular review to assure the trustworthiness of clinical guidelines is required. However, there is still a lack of preferred reporting items of the updating process in updated clinical guidelines. The present article describes the development process of the Checklist for the Reporting of Updated Guidelines (CheckUp). Methods and Findings We developed an initial list of items based on an overview of research evidence on clinical guideline updating, the Appraisal of Guidelines for Research and Evaluation (AGREE) II Instrument, and the advice of the CheckUp panel (n = 33 professionals). A multistep process was used to refine this list, including an assessment of ten existing updated clinical guidelines, interviews with key informants (response rate: 54.2%; 13/24), a three-round Delphi consensus survey with the CheckUp panel (33 participants), and an external review with clinical guideline methodologists (response rate: 90%; 53/59) and users (response rate: 55.6%; 10/18). CheckUp includes 16 items that address (1) the presentation of an updated guideline, (2) editorial independence, and (3) the methodology of the updating process. In this article, we present the methodology to develop CheckUp and include as a supplementary file an explanation and elaboration document. Conclusions CheckUp can be used to evaluate the completeness of reporting in updated guidelines and as a tool to inform guideline developers about reporting requirements. Editors may request its completion from guideline authors when submitting updated guidelines for publication. Adherence to CheckUp will likely enhance the comprehensiveness and transparency of clinical guideline updating for the benefit of patients and the public, health care professionals, and other relevant stakeholders. PMID:28072838

KEY COMPARISON: Final report on CCEM key comparison CCEM.RF-K10.CL (GT-RF/99-2) 'Power in 50 Ω coaxial lines, frequency: 50 MHz to 26 GHz' measurement techniques and results

NASA Astrophysics Data System (ADS)

Janik, Dieter; Inoue, T.; Michaud, A.

2006-01-01

This report summarizes the results and the measuring methods of an international key comparison between twelve national metrology institutes (NMIs) and is concerning the calibration factor of RF power sensors in the coaxial 3.5 mm line for frequencies up to 26 GHz. Two RF power travelling standards fitted with male PC 3.5 mm connectors were measured at seven frequencies. The following NMIs participated: NMIJ (Japan), NRC (Canada), NIST (USA), METAS (Switzerland), CSIR-NML (South Africa), NMIA (Australia), NPL (UK), SiQ (Slovenia), IEN (Italy), VNIIFTRI (Russian Federation), SPRING (Singapore) and PTB (Germany), as the pilot laboratory. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON: Final report of the CCQM-K56: Ca, Fe, Zn and Cu in whole fat soybean powder

NASA Astrophysics Data System (ADS)

Liandi, Ma; Qian, Wang

2010-01-01

The CCQM-K56 key comparison was organized by the Inorganic Analysis Working Group (IAWG) of CCQM as a follow-up to completed pilot study CCQM-P64 to test the abilities of national metrology institutes to measure the amount content of nutritious elements in whole fat soybean powder. A pilot study CCQM-P64.1 was conducted in parallel with this key comparison. The National Institute of Metrology (NIM), P. R. China, acted as the coordinating laboratory. Eleven NIMs participated in CCQM-K56. Four elements - Ca, Fe, Zn and Cu - in different concentration levels have been studied. Different measurement methods (IDMS, ICP-MS, ICP-OES, AAS and INAA) and the microwave digestion method were used. The agreement of the results of CCQM-K56 is very good, and obviously better than that of the original P64. It shows that the capability of all of the participants had been promoted from the original pilot study to this key comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Non-local gravity and comparison with observational datasets. II. Updated results and Bayesian model comparison with ΛCDM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dirian, Yves; Foffa, Stefano; Kunz, Martin

We present a comprehensive and updated comparison with cosmological observations of two non-local modifications of gravity previously introduced by our group, the so called RR and RT models. We implement the background evolution and the cosmological perturbations of the models in a modified Boltzmann code, using CLASS. We then test the non-local models against the Planck 2015 TT, TE, EE and Cosmic Microwave Background (CMB) lensing data, isotropic and anisotropic Baryonic Acoustic Oscillations (BAO) data, JLA supernovae, H {sub 0} measurements and growth rate data, and we perform Bayesian parameter estimation. We then compare the RR, RT and ΛCDM models,more » using the Savage-Dickey method. We find that the RT model and ΛCDM perform equally well, while the performance of the RR model with respect to ΛCDM depends on whether or not we include a prior on H {sub 0} based on local measurements.« less

Final report on the key comparison CCM.P-K4.2012 in absolute pressure from 1 Pa to 10 kPa

NASA Astrophysics Data System (ADS)

Ricker, Jacob; Hendricks, Jay; Bock, Thomas; Dominik, Pražák; Kobata, Tokihiko; Torres, Jorge; Sadkovskaya, Irina

2017-01-01

The report summarizes the Consultative Committee for Mass (CCM) key comparison CCM.P-K4.2012 for absolute pressure spanning the range of 1 Pa to 10 000 Pa. The comparison was carried out at six National Metrology Institutes (NMIs), including National Institute of Standards and Technology (NIST), Physikalisch-Technische Bundesanstalt (PTB), Czech Metrology Institute (CMI), National Metrology Institute of Japan (NMIJ), Centro Nacional de Metrología (CENAM), and DI Mendeleyev Institute for Metrology (VNIIM). The comparison was made via a calibrated transfer standard measured at each of the NMIs facilities using their laboratory standard during the period May 2012 to September 2013. The transfer package constructed for this comparison preformed as designed and provided a stable artifact to compare laboratory standards. Overall the participants were found to be statistically equivalent to the key comparison reference value. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Updates to Enhanced Geothermal System Resource Potential Estimate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Augustine, Chad

The deep EGS electricity generation resource potential estimate maintained by the National Renewable Energy Laboratory was updated using the most recent temperature-at-depth maps available from the Southern Methodist University Geothermal Laboratory. The previous study dates back to 2011 and was developed using the original temperature-at-depth maps showcased in the 2006 MIT Future of Geothermal Energy report. The methodology used to update the deep EGS resource potential is the same as in the previous study and is summarized in the paper. The updated deep EGS resource potential estimate was calculated for depths between 3 and 7 km and is binned inmore » 25 degrees C increments. The updated deep EGS electricity generation resource potential estimate is 4,349 GWe. A comparison of the estimates from the previous and updated studies shows a net increase of 117 GWe in the 3-7 km depth range, due mainly to increases in the underlying temperature-at-depth estimates from the updated maps.« less

EPA Monthly Key Performance Indicator Dashboards 2017

EPA Pesticide Factsheets

Each month, the Web Analytics Program posts updated Key Performance Indicator (KPI) dashboards that correspond to three Web performance goals: content consumption, content discovery, and audience engagement.

APMP key comparison for the measurement of air kerma for 60Co (APMP.RI(I)-K1.1)

NASA Astrophysics Data System (ADS)

Webb, D. V.; Lee, J.-H.; Budiantari, C. T.; Laban, J.; Saito, N.; Srimanoroth, S.; Khaled, N. E.

2016-01-01

The results are reported for an APMP.R(I)-K1.1 comparison that extends the regional comparison of standards for air kerma APMP.R(I)-K1 to several laboratories unable to participate earlier. The comparison was conducted with the goal of supporting the relevant calibration and measurement capabilities (CMCs) planned for publication by the participant laboratories. The comparison was conducted by the pilot laboratory, the Australian Radiation Protection and Nuclear Safety (ARPANSA), Australia, supported by the Institute of Nuclear Energy Research (INER), Taiwan, in a modified ring-shaped arrangement from September 2009 to November 2010, in parallel with an APMP.R(I)-K4 comparison being piloted by the INER. The laboratories that took part in the comparison were the ARPANSA, the Centre of Technology of Radiation Safety and Metrology (PTKMR-BATAN), Indonesia, the Division of Radiation and Medical Devices (DMSC), Thailand, the INER, the National Centre for Radiation Science (NCRS), New Zealand, the National Institute for Standards (NIS), Egypt and the National Metrology Institute of Japan (NMIJ/AIST), Japan. The two primary laboratories, ARPANSA and NMIJ, were chosen as the linking laboratories. Three ionization chambers were used as transfer instruments to be calibrated in terms of air kerma in 60Co radiotherapy beams. The comparison result is based on the ratio between the air kerma calibration coefficients (NK) determined by the participants and the mean of the results of the linking laboratories. The mean comparison ratio was found to be within 0.5 % of the key comparison reference value KCRV. The largest deviation between any two comparison ratios for the three chambers in terms of air kerma was 2.0 %. An analysis of the participant uncertainty budgets enabled the calculation of degrees of equivalence (DoE) in terms of the deviations of the results and their associated uncertainties. As a result of this APMP comparison, the BIPM key comparison database (KCDB) should

Summary of Expansions, Updates, and Results in GREET® 2016 Suite of Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

2016-10-01

This report documents the technical content of the expansions and updates in Argonne National Laboratory’s GREET® 2016 release and provides references and links to key documents related to these expansions and updates.

Final report on the key comparison of hydrocarbon liquid flow: CCM.FF-K2.2015

NASA Astrophysics Data System (ADS)

Shimada, T.; Bittner-Rohrhofer, K.; Medina López, V. J.; Arias, R.; Su, C.-M.; Chen, I.-C.; Ribere, F.; Rowan, L.; Dignan, S.

2016-01-01

Seven laboratories: BEV (Austria), CENAM (Mexico), CMS (Chinese-Taipei), LNE-TRAPIL (France), NEL (United Kingdom), NMIA (Australia), and the pilot lab NMIJ (Japan), participated in the key comparison CCM.FF-K2.2015 for hydrocarbon flow measurement. A screw type positive displacement flow meter was selected as a transfer standard. The calibration stability of the transfer standard was evaluated from repeated measurements by NMIJ and showed standard reproducibility of 0.0035 %. The transfer standard was also thoroughly tested for sensitivity to temperature, viscosity, pressure, and other effects. The uncertainty due to the transfer standard of 0.0080 % was less than the quoted uncertainties of the participants. The key comparison reference values (KCRVs) at Reynolds number of 70 000 and 300 000 were obtained as the weighted mean from the calibration results, and the KCRV at Reynolds number of 100 000 was obtained as the median by using the Monte Carlo method according to Cox's procedure B, since the consistency check at Reynolds number of 100 000 failed at the 95 % confidence level. All participant results selected to determine the KCRVs have En values which show consistency with the evaluated KCRVs. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 100 pF standards (ongoing BIPM key comparison BIPM.EM-K14.b) between the NSAI-NML (Ireland) and the BIPM

NASA Astrophysics Data System (ADS)

Gournay, Pierre; Power, Oliver

2017-01-01

This report presents the results of a bilateral comparison of capacitance at 100 pF between the NSAI-NML (Ireland) and the BIPM carried out in 2016. This comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.b in which the BIPM is the pilot laboratory. Two 100 pF travelling standards belonging to the BIPM were used in this comparison carried out with an 'A-B-A' pattern of measurements. The standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz, for a measuring rms voltage of 15 V. The results from the NSAI-NML and the BIPM were found to be in relatively good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 0.85 × 10-6. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: Final report on CCQM-K57: Chemical composition of clay

NASA Astrophysics Data System (ADS)

Salas, Antonio; Ramírez, Estele

2009-01-01

After the successful completion of the pilot study, CCQM-P65 [1], the Inorganic Analysis Working Group of CCQM agreed to conduct key comparison CCQM-K57, Chemical composition of clay, in Paris, April 2006. The natural mass fraction levels of five elements—Si, Ca, Fe, Al and Mg—were measured and reported as oxides in clay. Six national metrology institutes participated in CCQM K57, and CENAM (Querétaro, Mexico) coordinated. The methods employed were isotope dilution mass spectrometry (IDMS), inductively coupled plasma-mass spectrometry (ICP-MS), inductively coupled plasma-optical emission spectrometry (ICP-OES) using the dehydration method and condensation method, gravimetric analysis, neutron activation analysis (NAA), prompt gamma activation analysis (PGAA) and x-ray fluorescence spectrometry (XRF) with the reconstitution method and external calibration. This final report presents the capability of the participant institutes, based on the KCRV, which was approved at the IAWG spring meeting in 2008, and the equivalence statements regarding the KCRV, approved at its autumn meeting. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON: Final report on Key Comparison APMP.SIM.M.P-K1c: Bilateral comparison between NIST (USA) and NPLI (India) in the pneumatic pressure region 0.4 MPa to 4.0 MPa

NASA Astrophysics Data System (ADS)

Driver, R. Gregory; Olson, Douglas A.; Dilawar, Nita; Bandyopadhyay, A. K.

2007-01-01

We report the results of a bilateral comparison of pressure measurement between NIST and NPLI using a piston gauge transfer standard (TS), designated as NPLI-4, over the range of nominal applied pressure 0.4 MPa to 4.0 MPa. This TS was cross-floated against the laboratory secondary standard designated as PG13 at NIST, USA and against NPLI-8 at NPLI, India. The nominal pressure points of the bilateral comparison were (0.4, 0.8, 1.2, 1.6, 2.0, 2.4, 2.8, 3.2, 3.6 and 4.0) MPa, respectively. The comparison was performed in both the institutes in identical pressure cycles in increasing pressures. The comparison data were analysed in terms of the effective area [Ap (mm2)] as a function pressure [p (MPa)] of the TS at the above-mentioned pressures. We have also estimated the zero-pressure effective area [A0 (mm2)] and the pressure distortion coefficient [λ (MPa-1)] of the transfer standard. The consistency of the results at every pressure in the range indicates that the laboratory standards used in this comparison are compatible, uniform and can be considered traceable to each other. Finally, the degree of equivalence between NPLI and NIST is 11.4 × 10-6 or better, which is always less than the relative standard uncertainty of the difference (33.6 × 10-6). Main text. To reach the main text of this Paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

KEY COMPARISON: CCT-K2.1: NRC/VNIIFTRI bilateral comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

NASA Astrophysics Data System (ADS)

Hill, K. D.; Steele, A. G.; Dedikov, Y. A.; Shkraba, V. T.

2005-01-01

The Consultative Committee for Thermometry Key Comparison 2 (CCT-K2) results were published two years ago (2002 Metrologia 39 551-71). NRC served as the pilot laboratory for CCT-K2 and remains able to provide a scale and measurement system suitable for performing bilateral comparisons linked to the original key comparison results. In March 2003, measurements of two VNIIFTRI 100 Ω capsule-style platinum resistance thermometers (CSPRTs), S/N 356 and 476, were undertaken to relate their local calibration to the results from the CCT-K2 exercise. The NRC Leeds and Northrup (L&N) CSPRT S/N 1872174 provides the link to the CCT-K2 results. The three CSPRTs were compared at the eight defining cryogenic temperatures of the International Temperature Scale of 1990 (ITS-90) in the range from 13.8033 K to 273.16 K. The reader is referred to the full text of the CCT-K2 report for a detailed explanation of the methodology employed for the comparison. Only the details unique to the measurements reported here will be addressed in this article. The NRC/VNIIFTRI bilateral comparison of capsule-style platinum resistance thermometers over the range 13.8 K to 273.16 K has revealed calibrations at VNIIFTRI to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison with the exception of the triple point of hydrogen at 13.8033 K. One of the two CSPRTs supplied by VNIIFTRI was found to be discrepant as revealed by differences at the triple point of water and at the lowest temperatures of the comparison, and was therefore excluded from further analysis. The linkage to the CCT-K2 data supports the evaluation of the VNIIFTRI CMCs in Appendix C of the KCDB. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions

Final report of CCAUV.V-K3: key comparison in the field of acceleration on the complex charge sensitivity

NASA Astrophysics Data System (ADS)

Qiao, Sun; Lifeng, Yang; Bartoli, Claire; Veldman, Ian; Ripper, Gustavo P.; Bruns, Thomas; Rask Licht, Torben; Kolasa, Joanna; Hof, Christian; Silva Pineda, Guillermo; Dickinson, Laurence; Ota, Akihiro; Cheung, Wan Sup; Yankovsky, Alexander; Shan, Cui

2017-01-01

This is the final report for CIPM key comparison CCAUV.V-K3 in the area of 'vibration' (quantity of acceleration). The aim of this comparison was to measure the voltage sensitivity of one accelerometer standard set with primary means at 27 frequencies from 0.1 Hz to 40 Hz. Fourteen Metrology Institutes from five RMOs have participated in the comparison with National Institute of Metrology, P.R. China as pilot lab and Laboratoire National de Métrologie et d'Essais and National Metrology Institute of South Africa as co-pilot labs. One quartz-flexure servo accelerometer of single-ended type and a signal conditioner was circulated among the participants. All but one of the participating laboratories provided their calibration results, which were mostly consistent within their declared expanded uncertainties for magnitude results. Only two participants failed to contribute to the KCRV values calculated for five frequencies. For phase shift, three participants could not contribute to the calculation of the KCRV values in a total of sixteen frequencies. This first low-frequency vibration key comparison revealed the current calibration capabilities of the fourteen participants of five RMOs. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Austin Community College Benchmarking Update.

ERIC Educational Resources Information Center

Austin Community Coll., TX. Office of Institutional Effectiveness.

Austin Community College contracted with MGT of America, Inc. in spring 1999 to develop a peer and benchmark (best) practices analysis on key indicators. These indicators were updated in spring 2002 using data from eight Texas community colleges and four non-Texas institutions that represent large, comprehensive, urban community colleges, similar…

Final Report on the Key Comparison CCM.P-K4.2012 in Absolute Pressure from 1 Pa to 10 kPa

PubMed Central

Ricker, Jacob; Hendricks, Jay; Bock, Thomas; Dominik, Pražák; Kobata, Tokihiko; Torres, Jorge; Sadkovskaya, Irina

2017-01-01

The report summarizes the Consultative Committee for Mass (CCM) key comparison CCM.P-K4.2012 for absolute pressure spanning the range of 1 Pa to 10 000 Pa. The comparison was carried out at six National Metrology Institutes (NMIs), including National Institute of Standards and Technology (NIST), Physikalisch-Technische Bundesanstalt (PTB), Czech Metrology Institute (CMI), National Metrology Institute of Japan (NMIJ), Centro Nacional de Metrología (CENAM), and DI Mendeleyev Institute for Metrology (VNIIM). The comparison was made via a calibrated transfer standard measured at each of the NMIs facilities using their laboratory standard during the period May 2012 to September 2013. The transfer package constructed for this comparison preformed as designed and provided a stable artifact to compare laboratory standards. Overall the participants were found to be statistically equivalent to the key comparison reference value. PMID:28216793

[Cardiology update in 2016].

PubMed

Gabus, Vincent; Tran, Van Nam; Regamey, Julien; Pascale, Patrizio; Monney, Pierre; Hullin, Roger; Vogt, Pierre

2017-01-11

In 2016 the European Society of Cardiology (ESC) published new guidelines. These documents update the knowledge in various fields such as atrial fibrillation, heart failure, cardiovascular prevention and dyslipidemia. Of course it is impossible to summarize these guidelines in detail. Nevertheless, we decided to highlight the major modifications, and to emphasize some key points that are especially useful for the primary care physician.

Update to Enhanced Geothermal System Resource Potential Estimate: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Augustine, Chad

2016-10-01

The deep EGS electricity generation resource potential estimate maintained by the National Renewable Energy Laboratory was updated using the most recent temperature-at-depth maps available from the Southern Methodist University Geothermal Laboratory. The previous study dates back to 2011 and was developed using the original temperature-at-depth maps showcased in the 2006 MIT Future of Geothermal Energy report. The methodology used to update the deep EGS resource potential is the same as in the previous study and is summarized in the paper. The updated deep EGS resource potential estimate was calculated for depths between 3 and 7 km and is binned inmore » 25 degrees C increments. The updated deep EGS electricity generation resource potential estimate is 4,349 GWe. A comparison of the estimates from the previous and updated studies shows a net increase of 117 GWe in the 3-7 km depth range, due mainly to increases in the underlying temperature-at-depth estimates from the updated maps.« less

An Essential Vocabulary: An Update.

ERIC Educational Resources Information Center

Davis, Anita P.; McDaniel, Thomas R.

1998-01-01

Updates a list (originally published in 1963) of "survival" or essential words--words so important for survival and success in everyday life that everyone should know them. Notes that recognition of these key words and phrases may require non-English-speaking individuals, disabled readers, and adult literacy students to use rote memorization for…

KEY COMPARISON: Final report of EUROMET Project 696: pH determination of a phthalate buffer

NASA Astrophysics Data System (ADS)

Spitzer, Petra; Charlet, Philippe; Eberhard, Ralf; Karpov, Oleg V.; Philippe, Rachel; Rivier, Cedric; Maximov, Igor; Sudmeier, Uwe

2005-01-01

The EUROMET project 696, a trilateral comparison between PTB, Germany, LNE, France and VNIIFTRI, Russia was performed in order to demonstrate and document the capability of the participants to measure the pH of a phthalate buffer by the primary measurement procedure for pH. Good agreement of the reported results was observed. The sample was very similar to the one used in the comparison CCQM-K17. PTB acts as pilot laboratory in CCQM-K17 and in EUROMET 696. This comparison allows one to link the results obtained by LNE to the CCQM-K17 key comparison through the degree of equivalence of PTB. On the other hand, the discrepancy between measured pH values at the VNIIFTRI and PTB for the same type of buffer solution decreased, as compared with a bilateral comparison in 1997. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the Mutual Recognition Arrangement (MRA).

KEY COMPARISON: Final Report on EUROMET.T-K3: Regional key comparison of the realisations of the ITS-90 from 83.8058 K to 692.677 K

NASA Astrophysics Data System (ADS)

Renaot, E.; Hermier, Y.; Valin, M.; Bonnier, G.

2007-01-01

This report presents the results of the EUROMET regional key comparison corresponding to CCT-K3 and covering the temperature range from 83.8058 K (triple point of Ar) to 692.77 K (freezing point of Zn). The comparison involved the six NMIs previously involved in CCT-K3 (BNM-INM/CNAM, SMU, IMGC, NMi-VSL, NPL, PTB) and 18 European national laboratories. The comparison was divided into five different loops coordinated by a co-pilot chosen among the laboratories having participated in the CCT-K3 comparison. BNM-INM/CNAM played the role of pilot in establishing the link between the five loops. In each loop, an artefact in the form of a standard platinum resistance thermometer (SPRT) was circulated among the participant laboratories. In order to have sufficient information about the possible drift of the SPRTs, the co-pilots have performed a calibration over the full temperature range at the beginning and at the end of the loop. Each participant laboratory carried out the measurements in agreement with the protocol. After initial measurements of R(tpw) and successful annealing treatment, each calibration consisted of three measurements of R(t) at each fixed point, in separate realizations. Each measurement was followed by a measurement of R(tpw). The order of fixed points was Zn, Sn, In, Ga, Hg, Ar, but if a fixed point was not available, it was omitted. Values of W(t), and their average value, were calculated. The results were reported to the co-pilot and BNM-INM/CNAM, with uncertainty budgets and other specified data. The results of the comparison were analysed by BNM-INM/CNAM. For the sake of clarity, the results are firstly presented loop by loop. In a second step a EUROMET Reference Value (ERV) taking into account the whole comparison was defined. In order to calculate this ERV advantage was taken of the presence of BNM-INM/CNAM in the five loops; the differences between each laboratory's results and BNM-INM's were considered. The participant laboratories decided

Higher Education in England 2016: Key Facts. September 2016/20

ERIC Educational Resources Information Center

Higher Education Funding Council for England, 2016

2016-01-01

This updated edition of "Higher Education in England: Key Facts" provides a statistical overview of key sector trends and developments in 2016. Using the most recent data, it draws together key findings from a range of reports published by the Higher Education Funding Council for England (HEFCE) over the past year to provide a robust,…

DigitalGlobe(TM) Incorporated Corporate and System Update

NASA Technical Reports Server (NTRS)

Thomassie, Brett

2007-01-01

This viewgraph presentation describes a system update of Quickbird, the world's highest resolution commercial imaging satellite, operated by DigitalGlobe (TM) Incorporated. A satellite comparison of Quickbird, WorldView-60, and WorldView-110 is also presented.

The distance effect in numerical memory-updating tasks.

PubMed

Lendínez, Cristina; Pelegrina, Santiago; Lechuga, Teresa

2011-05-01

Two experiments examined the role of numerical distance in updating numerical information in working memory. In the first experiment, participants had to memorize a new number only when it was smaller than a previously memorized number. In the second experiment, updating was based on an external signal, which removed the need to perform any numerical comparison. In both experiments, distance between the memorized number and the new one was manipulated. The results showed that smaller distances between the new and the old information led to shorter updating times. This graded facilitation suggests that the process by which information is substituted in the focus of attention involves maintaining the shared features between the new and the old number activated and selecting other new features to be activated. Thus, the updating cost may be related to amount of new features to be activated in the focus of attention.

Key comparison SIM.EM.RF-K5b.CL: scattering coefficients by broad-band methods, 2 GHz-18 GHz — type N connector

NASA Astrophysics Data System (ADS)

Silva, H.; Monasterios, G.

2016-01-01

The first key comparison in microwave frequencies within the SIM (Sistema Interamericano de Metrología) region has been carried out. The measurands were the S-parameters of 50 ohm coaxial devices with Type-N connectors and were measured at 2 GHz, 9 GHz and 18 GHz. SIM.EM.RF-K5b.CL was the identification assigned and it was based on a parent CCEM key comparison named CCEM.RF-K5b.CL. For this reason, the measurements standards and their nominal values were selected accordingly, i.e. two one-port devices (a matched and a mismatched load) to cover low and high reflection coefficients and two attenuators (3dB and 20 dB) to cover low and high transmission coefficients. This key comparison has met the need for ensuring traceability in high-frequency measurements across America by linking SIM's results to CCEM. Six NMIs have participated in this comparison which was piloted by the Instituto Nacional de Tecnología Industrial (Argentina). A linking method of multivariate values was proposed and implemented in order to allow the linking of 2-dimensional results. KEY WORDS FOR SEARCH Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: Results of the APMP Pressure key comparison APMP.M.P-K1c in gas media and gauge mode from 0.4 MPa to 4.0 MPa

NASA Astrophysics Data System (ADS)

Bandyopadhyay, A. K.; Woo, Sam Yong; Fitzgerald, Mark; Man, John; Ooiwa, Akira; Jescheck, M.; Jian, Wu; Fatt, Chen Soo; Chan, T. K.; Moore, Ken; El-Tawil, Alaaeldin A. E.

2003-01-01

This report summarizes the results of a regional key comparison (APMP-IC-2-97) under the aegis of the Asia Pacific Metrology Program (APMP) for pressure measurements in gas media and in gauge mode from 0.4 MPa to 4.0 MPa. The transfer standard was a pressure-balance with a piston-cylinder assembly with nominal effective area 8.4 mm2 (V-407) and was supplied by the National Metrology Institute of Japan [NMIJ]. Ten standard laboratories from the APMP region with one specially invited laboratory from the EUROMET region, namely Physikalisch-Technische Bundesanstalt (PTB), Germany, participated in this comparison. The comparison started in October 1998 and was completed in May 2001. The pilot laboratory prepared the calibration procedure [1] as per the guidelines of APMP and the International Bureau of Weights and Measures (BIPM) [2-4]. Detailed instructions for performing this key comparison were provided in the calibration protocol [1] and the required data were described in: (1) Annex 3 - characteristics of the laboratory standards, (2) Annex 4 - the effective area (A'p'/mm2) (the prime indicates values based on measured quantities) at 23°C of the travelling standard as a function of nominal pressure (p'/MPa) (five cycles both increasing and decreasing pressures at ten pre-determined pressure points) and (3) Annex 5 - the average effective area at 23°C (A'p'/mm2) obtained for each pressure p'/MPa with all uncertainty statements. The pilot laboratory processed the information and the data provided by the participants for these three annexes, starting with the information about the standards as provided in Annex 3. Based on this information, the participating laboratories are classified into two categories: (I) laboratories that are maintaining primary standards, and (II) laboratories that are maintaining standards loosely classified as secondary standards with a clear traceability as per norm of the BIPM. It is observed that out of these eleven laboratories, six

Static and Dynamic Model Update of an Inflatable/Rigidizable Torus Structure

NASA Technical Reports Server (NTRS)

Horta, Lucas G.; Reaves, mercedes C.

2006-01-01

The present work addresses the development of an experimental and computational procedure for validating finite element models. A torus structure, part of an inflatable/rigidizable Hexapod, is used to demonstrate the approach. Because of fabrication, materials, and geometric uncertainties, a statistical approach combined with optimization is used to modify key model parameters. Static test results are used to update stiffness parameters and dynamic test results are used to update the mass distribution. Updated parameters are computed using gradient and non-gradient based optimization algorithms. Results show significant improvements in model predictions after parameters are updated. Lessons learned in the areas of test procedures, modeling approaches, and uncertainties quantification are presented.

KEY COMPARISON: CCEM.RF-K9: International comparison of thermal noise standards between 12.4 GHz and 18 GHz (GT-RF/99-1)

NASA Astrophysics Data System (ADS)

Allal, Djamel; Achkar, Joseph

2006-01-01

An international comparison of thermal noise-power measurements has been carried out among five national metrology institutes between 12.4 GHz and 18 GHz. Four transfer standards were measured. The following national institutes participated: BNM-LCIE (France), NPL (United Kingdom), PTB (Germany), NIST (United States of America) and VNIIFTRI (Russia). The Bureau National de Métrologie-Laboratoire Central des Industries Electriques (France) acted as the pilot laboratory for the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

National Drug Control Strategy. Update

ERIC Educational Resources Information Center

Office of National Drug Control Policy, 2005

2005-01-01

The first National Drug Control Strategy set ambitious two and five-year performance based goals: (1) to lower the rate of drug use by 10 percent over 2 years among both youth and adults; and (2) to lower the rate by 25 percent over 5 years. The chapters in this updated version are keyed to the strategies three priorities: (1) Stopping Use Before…

Key comparison BIPM.RI(I)-K3 of the air-kerma standards of the NIST, USA and the BIPM in medium-energy x-rays.

PubMed

Burns, D T; Kessler, C; O'Brien, M; Minniti, R

2012-01-01

A key comparison has been made between the air-kerma standards of the NIST, USA and the BIPM in the medium-energy x-ray range. The results show the standards to be in agreement at the level of the standard uncertainty of the comparison of 3.8 parts in 10 3 , except at 250 kV where the difference is 1.5 times the standard uncertainty. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database.

Updating the mitochondrial free radical theory of aging: an integrated view, key aspects, and confounding concepts.

PubMed

Barja, Gustavo

2013-10-20

An updated version of the mitochondrial free radical theory of aging (MFRTA) and longevity is reviewed. Key aspects of the theory are emphasized. Another main focus concerns common misconceptions that can mislead investigators from other specialties, even to wrongly discard the theory. Those different issues include (i) the main reactive oxygen species (ROS)-generating site in the respiratory chain in relation to aging and longevity: complex I; (ii) the close vicinity or even contact between that site and the mitochondrial DNA, in relation to the lack of local efficacy of antioxidants and to sub-cellular compartmentation; (iii) the relationship between mitochondrial ROS production and oxygen consumption; (iv) recent criticisms on the MFRTA; (v) the widespread assumption that ROS are simple "by-products" of the mitochondrial respiratory chain; (vi) the unnecessary postulation of "vicious cycle" hypotheses of mitochondrial ROS generation which are not central to the free radical theory of aging; and (vii) the role of DNA repair concerning endogenous versus exogenous damage. After considering the large body of data already available, two general characteristics responsible for the high maintenance degree of long-lived animals emerge: (i) a low generation rate of endogenous damage: and (ii) the possession of tissue macromolecules that are highly resistant to oxidative modification.

Key comparison BIPM.RI(I)-K9 of the absorbed dose to water standards of the PTB, Germany and the BIPM in medium-energy x-rays

NASA Astrophysics Data System (ADS)

Burns, D. T.; Kessler, C.; Büermann, L.; Ketelhut, S.

2018-01-01

A key comparison has been made between the absorbed dose to water standards of the PTB, Germany and the BIPM in the medium-energy x-ray range. The results show the standards to be in general agreement at the level of the standard uncertainty of the comparison of 9 to 11 parts in 103. The results are combined with those of a EURAMET comparison and presented in terms of degrees of equivalence for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Key comparison BIPM.RI(I)-K1 of the air-kerma standards of the SMU, Slovakia and the BIPM in 60Co gamma radiation

NASA Astrophysics Data System (ADS)

Kessler, C.; Burns, D.; Durný, N.

2018-01-01

A key comparison of the standards for air kerma of the Slovak Institute of Metrology (SMU), Slovakia and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 60Co radiation beam of the BIPM in June 2017. The comparison result, evaluated as a ratio of the SMU and the BIPM standards for air kerma, is 1.0042 with a combined standard uncertainty of 2.7 × 10-3. The results for an indirect comparison made at the same time are consistent with the direct results at the level of 2 parts in 104. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

A Comparison of Updating Processes in Children Good or Poor in Arithmetic Word Problem-Solving

ERIC Educational Resources Information Center

Passolunghi, Maria Chiara; Pazzaglia, Francesca

2005-01-01

This study examines the updating ability of poor or good problem solvers. Seventy-eight fourth-graders, 43 good and 35 poor arithmetic word problem-solvers, performed the Updating Test used in Palladino et al. [Palladino, P., Cornoldi, C., De Beni, R., and Pazzaglia F. (2002). Working memory and updating processes in reading comprehension. Memory…

Final report on SIM Regional Key Comparison SIM.L-K1.2007: Calibration of gauge blocks by optical interferometry

NASA Astrophysics Data System (ADS)

Colín, C.; Viliesid, M.; Chaudhary, K. P.; Decker, J.; Dvorácek, F.; Franca, R.; Ilieff, S.; Rodríguez, J.; Stoup, J.

2012-01-01

This Key Comparison of gauge blocks (GB) calibration by optical interferometry was carried out to support this Calibration and Measurement Capability (CMC) of the National Measurement Institutes (NMI) from the SIM Region for this specific service and for those that rely on this kind of technique as required by the Mutual Recognition Arrangement (MRA). It provides evidence of the participant's technical competence and supports the uncertainties they state in their CMC. It is a Regional Key Comparison and should be linked to the upper level corresponding comparison CCL-K1. The comparison had nine participants, five from the SIM Region—NRC-CNRC, Canada; NIST, USA; CENAM, Mexico; INMETRO, Brazil; and INTI, Argentina— and four from other regions—CMI, Czech Rep.; CEM, Spain; NPLI, India; and NMISA South Africa. It included the circulation of fourteen GB—seven steel GB and seven ceramic GB. The circulation of the artifacts started on 2007-11-01 and ended on 2010-04-25. Some additional time was required to publish the results as the same artifacts were used thereafter for comparison SIM.L-S6, Calibration of GB by mechanical comparison, and the results could not be disclosed until the participants of the second circulation loop had sent their results. The final report of this comparison was sent out for review in May 2012 and the final version was approved in August 2012. The behavior of the artifacts throughout the circulation was good and therefore the results obtained were judged technically valid. The reference value was taken as arithmetic mean of the largest subset of consistent results. Most of participates obtained results in good agreement with the reference values with a few exceptions mentioned in the report. The corresponding NMIs are responsible for identifying the causes and taking corrective action. This makes the present comparison exercise valid to support the CMC claims of the participants in GB calibration by optical interferometry. Main text. To

Cebrennus Simon, 1880 (Araneae: Sparassidae): a revisionary up-date with the description of four new species and an updated identification key for all species.

PubMed

Jäger, Peter

2014-04-17

The spider genus Cebrennus Simon, 1880 is revised again after thirteen years. Four new species are described: Cebrennus atlas spec. nov. from Morocco (female), C. flagellatus spec. nov. from Afghanistan (male), C. laurae spec. nov. from Canary Islands (male), and C. rechenbergi spec. nov. from Morocco (male and female). Cebrennus clercki (Audouin, 1826) comb. nov. is transferred from Philodromidae to Sparassidae and considered a nomen dubium. The holotype of C. aethiopicus Simon, 1880 is illustrated for the first time. Cebrennus tunetanus Simon, 1885 is re-described by illustrating its copulatory organs and some somatic characters, the internal duct system is shown for the first time supporting its placement in Cebrennus. An updated identification key for all species is provided. New records of Cebrennus species are listed: C. wagae (Simon, 1874) is recorded from Libya and Malta for the first time, the latter representing the first record for the entire genus from Europe. C. kochi (O. Pickard-Cambridge, 1872) is recorded from Syria, C. aethiopicus from Sudan for the first time. Records from the Canary Islands and from Afghanistan extend the known generic distribution range further to the West and East. Behavioural aspects (burrowing, escaping, mating) of C. rechenbergi and partly of C. villosus (Jézéquel & Junqua, 1966) are described. Photographs of this behaviour as well as of the habitus of several species are provided.

Key comparison BIPM.RI(I)-K3 of the air-kerma standards of the NIST, USA and the BIPM in medium-energy x-rays

PubMed Central

Burns, D T; Kessler, C; O’Brien, M; Minniti, R

2017-01-01

A key comparison has been made between the air-kerma standards of the NIST, USA and the BIPM in the medium-energy x–ray range. The results show the standards to be in agreement at the level of the standard uncertainty of the comparison of 3.8 parts in 103, except at 250 kV where the difference is 1.5 times the standard uncertainty. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. PMID:28966399

Final report on key comparison EURAMET.M.P-K13 in the range 50 MPa to 500 MPa of hydraulic gauge pressure

NASA Astrophysics Data System (ADS)

Kocas, I.; Sabuga, W.; Bergoglio, M.; Eltaweel, A.; Korasie, C.; Farar, P.; Setina, J.; Waller, B.; Durgut, Y.

2015-01-01

The regional key comparison EURAMET.M.P-K13 for pressure measurements in liquid media from 50 MPa to 500 MPa was piloted by the TÜBİTAK UME Pressure Group Laboratories, Turkey. The transfer standard was a DH-Budenberg pressure balance with a free deformation piston-cylinder unit of 2 mm2 nominal effective area. Six laboratories from the EURAMET region, namely PTB, INRIM, SMU, IMT, NPL and UME, and two laboratories from the AFRIMETS region, NIS and NMISA participated in this comparison. Participant laboratories and countries are given in the bottom of the page. PTB participated in this comparison to provide a link to corresponding 500 MPa CCM key comparison CCM.P-K13. The results of all participants excepting NMISA and NPL were found to be consistent with the reference value of the actual comparison and of CCM.P-K13 within their claimed uncertainties (k = 2), at all pressures. Compared in pairs all laboratories with exception of NPL and NMISA demonstrate their agreement with each other within the expanded uncertainties (k = 2) at all pressures. The results are therefore considered to be satisfactory. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Risk Assessment Update: Russian Segment

NASA Technical Reports Server (NTRS)

Christiansen, Eric; Lear, Dana; Hyde, James; Bjorkman, Michael; Hoffman, Kevin

2012-01-01

BUMPER-II version 1.95j source code was provided to RSC-E- and Khrunichev at January 2012 MMOD TIM in Moscow. MEMCxP and ORDEM 3.0 environments implemented as external data files. NASA provided a sample ORDEM 3.0 g."key" & "daf" environment file set for demonstration and benchmarking BUMPER -II v1.95j installation at the Jan-12 TIM. ORDEM 3.0 has been completed and is currently in beta testing. NASA will provide a preliminary set of ORDEM 3.0 ".key" & ".daf" environment files for the years 2012 through 2028. Bumper output files produced using the new ORDEM 3.0 data files are intended for internal use only, not for requirements verification. Output files will contain these words ORDEM FILE DESCRIPTION = PRELIMINARY VERSION: not for production. The projectile density term in many BUMPER-II ballistic limit equations will need to be updated. Cube demo scripts and output files delivered at the Jan-12 TIM have been updated for the new ORDEM 3.0 data files. Risk assessment results based on ORDEM 3.0 and MEM will be presented for the Russian Segment (RS) of ISS.

Report on key comparison COOMET.AUV.A-K5: pressure calibration of laboratory standard microphones in the frequency range 2 Hz to 10 kHz

NASA Astrophysics Data System (ADS)

Dobrowolska, D.; Kosterov, A.

2016-01-01

This is the final report for regional key comparison COOMET.AUV.A-K5 on the pressure calibration of laboratory standard microphones in the frequency range from 2 Hz to 10 kHz. Two laboratories—Central Office of Measures (GUM)—the national metrology institute for Poland and the State Enterprise Scientific-Research Institute for Metrology of Measurement and Control Systems (DP NDI Systema)— the designated institute for acoustics in Ukraine took part in this comparison with the GUM as a pilot. One travelling type LS1P microphone was circulated to the participants and results in the form of regular calibration certificates were collected. The results of the DP NDI Systema obtained in this comparison were linked to the CCAUV.A-K5 key comparison through the joint participation of the GUM. The degrees of equivalence were computed for DP NDI Systema with respect to the CCAUV.A-K5 key comparison reference value. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

The Keys to Effective Schools: Educational Reform as Continuous Improvement

ERIC Educational Resources Information Center

Hawley, Willis D., Ed.

2006-01-01

Working in tandem with the powerful National Education Association's KEYS initiative (Keys to Excellence in Your Schools), this second edition focuses on how to change a school's organizational structure and culture to improve the quality of teaching and learning. Each chapter, revised and updated to address continuous improvement and narrowing…

CSTT Update: Fuel Quality Analyzer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brosha, Eric L.; Lujan, Roger W.; Mukundan, Rangachary

These are slides from a presentation. The following topics are covered: project background (scope and approach), developing the prototype (timeline), update on intellectual property, analyzer comparisons (improving humidification, stabilizing the baseline, applying clean-up strategy, impact of ionomer content and improving clean-up), proposed operating mode, considerations for testing in real-world conditions (Gen 1 analyzer electronics development, testing partner identified, field trial planning), summary, and future work.

Bilateral key comparison CCM.P-K3.1 for absolute pressure measurements from 3 × 10-6 Pa to 9 × 10-4 Pa

NASA Astrophysics Data System (ADS)

Fedchak, J. A.; Bock, Th; Jousten, K.

2014-01-01

This report describes the bilateral key comparison CCM.P-K3.1 between the National Institute of Standards and Technology (NIST) and Physikalisch-Technische Bundesanstalt (PTB) for absolute pressure in the range from 3 × 10-6 Pa to 9 × 10-4 Pa. This comparison was a follow-up to the comparison CCM.P-K3. Two ionization gauges and two spinning rotor gauges (SRGs) were used as the transfer standards for the comparison. The SRGs were used to compare the standards at a pressure of 9 × 10-4 Pa and to normalize the ionization gauge readings. The two ionization gauges were used to compare the standards in the pressure range of from 3 × 10-6 Pa to 3 × 10-4 Pa. Both laboratories used dynamic expansion chambers as standards in the comparison. The two labs showed excellent agreement with each other and with the CCM.P-K3 key comparison reference value (KCRV) over the entire range. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 10 pF and 100 pF standards (ongoing BIPM key comparisons BIPM.EM-K14.a and 14.b) between the NIS (Egypt) and the BIPM

NASA Astrophysics Data System (ADS)

Gournay, Pierre; Helmy, M.; Raouf, A.; Hamed, Heba A. M.; Eliwa Gad, A.

2017-01-01

This report presents the results of a bilateral comparison of 10 pF and 100 pF capacitance standards between the NIS (Egypt) and the BIPM carried out in 2016. The comparison at 10 pF forms part of the ongoing BIPM key comparison BIPM.EM-K14.a and that at 100 pF of the ongoing BIPM key comparison BIPM.EM-K14.b. The BIPM is the pilot laboratory for both of these comparisons. Two 10 pF and 100 pF travelling standards belonging to the BIPM were used in this comparison carried out with an 'A-B-A' pattern of measurements. The standards were measured first at the BIPM for a period of about one month, then for a similar period at the NIS, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of either 1000 Hz or 1592 Hz, for a measuring rms voltage of 15 V at 10 pF and 10 V at 100 pF. One of the 10 pF travelling standards had to be eliminated from the comparison due to a bistable behaviour, possibly due to transportation. The results from the NIS and the BIPM at both 1000 Hz and 1592 Hz were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of about 0.72 × 10-6 at 10 pF and about 0.65 × 10-6 at 100 pF. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Report of the key comparison CCQM-K108 determination of arsenic species, total arsenic and cadmium in brown rice flour

NASA Astrophysics Data System (ADS)

Hioki, Akiharu; Narukawa, Tomohiro; Inagaki, Kazumi; Miyashita, Shinichi; Kotzeva, Boriana; Kakoulides, Elias; Sxoina, Vasiliki; Fung, W. H.; Choi, Y. Y.; Yau, H. P.; Tsoi, Y. T.; Lee, C. L.; Kong, M. F.; Shin, Richard; Juan, Wang; Sin Yee, Ng; Uribe, Christian; Marques Rodrigues, Janaína; Caciano de Sena, Rodrigo; Silva Dutra, Emily; Bergamaschi, Luigi; Giordani, Laura; D'Agostino, Giancarlo; Valiente, Liliana; Horvat, Milena; Jacimovic, Radojko; Oduor Okumu, Tom; Kang'Iri, Jacqueline; Owiti Orwa, Tabitha; Chao, Wei; Jingbo, Chao; Taebunpakul, Sutthinun; Yafa, Charun; Kaewkhomdee, Nattikarn; Chailap, Benjamat; Pharat, Yanee; Phukphattanachai, Pranee; Turk, Gregory C.; Long, Stephen; Murphy, K. E.; Davis, Clay; Ellisor, Michael; Merrick, Jeffrey; White, Ian; Saxby, David; Linsky, S. M.; Barzev, A.; Botha, A.

2015-01-01

The CCQM-K108 key comparison was organised by the Inorganic Analysis Working Group (IAWG) of CCQM to test the abilities of national metrology institutes (NMIs) or designated institutes (DIs) to measure the mass fractions of arsenic species, total arsenic and cadmium in brown rice flour. The National Metrology Institute of Japan (NMIJ) acted as the coordinating laboratory. The participants used different measurement methods, though most of them used inductively coupled plasma mass spectrometry (ICP-MS) or isotope-dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) for Cd and ICP-MS for total arsenic. Regarding arsenic speciation, all participants used ICP-MS coupled with liquid chromatography (LC). Accounting for relative expanded uncertainty, comparability of measurement results for each of total arsenic and cadmium was successfully demonstrated by the participating NMIs or DIs for the measurement of the measurand at the level of less than 0.5 mg/kg. Regarding arsenic species (inorganic arsenic and dimethylarsinic acid (DMAA)), there was, however, a measurement problem still to be solved and that part of CCQM-K108 will be repeated. It is expected that arsenic, cadmium and other metals at mass fractions greater than approximately 0.1 mg/kg in rice flour can be determined by each participant using the same technique(s) employed for this key comparison to achieve similar uncertainties mentioned in the present report. Furthermore, the results of this key comparison can be utilised along with the IAWG core capability approach. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on APMP.T-K7.1 key comparison of water triple point cells, bilateral NMIJ-VMI

NASA Astrophysics Data System (ADS)

Yamazawa, Kazuaki; Nakano, Tohru; Thanh Binh, Pham

2018-01-01

APMP.T-K7.1, was held from July 2014 to May 2015 to compare the national realizations of the water triple point between NMIJ (Japan) and VMI (Vietnam). To reach the objective, VMI sent a transfer cell to NMIJ and stated a value for the temperature difference of the transfer cell, relative to the corresponding national standard, representing 273.16 K. This report presents the results of the TPW comparison, gives detailed information about the measurements made at the NMIJ and at the VMI, and aims to link the results of APMP.T-K7.1 to APMP.T-K7 and CCT-K7. The results of this key comparison are also represented in the form of degrees of equivalence for the purposes of the MRA. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 100 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.b) between the BIM, Bulgaria, and the BIPM, April 2012 to September 2012

NASA Astrophysics Data System (ADS)

Sapunova, I.; Fletcher, N.; Goebel, R.; Stock, M.

2015-01-01

This report gives the result of a bilateral comparison of capacitance between the BIM (Bulgaria) and the BIPM carried out in 2012. Two 100 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the BIM, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz and for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.a. The results from the BIM and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 1.1 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 10 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.a) between the BIM, Bulgaria, and the BIPM, April 2012 to September 2012

NASA Astrophysics Data System (ADS)

Sapunova, I.; Fletcher, N.; Goebel, R.; Stock, M.

2015-01-01

This report gives the result of a bilateral comparison of capacitance between the BIM (Bulgaria) and the BIPM carried out in 2012. Two 10 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the BIM, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz and for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.a. The results from the BIM and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 1.1 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 100 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.b) between the NSAI-NML, Ireland, and the BIPM, March-August 2011

NASA Astrophysics Data System (ADS)

Power, O.; Moran, A.; Fletcher, N.; Goebel, R.; Stock, M.

2015-01-01

This report gives the result of a bilateral comparison of capacitance between the NSAI-NML (Ireland) and the BIPM carried out in 2011. Two 100 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz, for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.b. The results from the NSAI-NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 0.66 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 10 pF capacitance standards (ongoing BIPM key comparison BIPM.EM-K14.a) between the NSAI-NML, Ireland, and the BIPM, March-August 2011

NASA Astrophysics Data System (ADS)

Power, O.; Moran, A.; Fletcher, N.; Goebel, R.; Stock, M.

2015-01-01

This report gives the result of a bilateral comparison of capacitance between the NSAI-NML (Ireland) and the BIPM carried out in 2011. Two 10 pF travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A—B—A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of 1000 Hz for a measuring voltage of 15 V. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparison BIPM.EM-K14.a. The results from the NSAI-NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of 2.5 × 10-6. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Update in Diffuse Parenchymal Lung Disease 2013

PubMed Central

Kaminski, Naftali

2015-01-01

The period covered by this update can be considered as the most exciting period in idiopathic pulmonary fibrosis (IPF) research. It started with the identification of genetic variants that are associated with IPF in the majority of patients and continued with discovery of molecular and genetic biomarkers that predict distinct clinical presentations of patients with IPF and potential new biological mechanisms. More importantly, the period ends with the publication of two groundbreaking studies that confirmed that two drugs, pirfenidone and nintedanib, slowed disease progression, leading to a historic approval by the FDA. In this update, we describe these key advances, their scientific and significant clinical implications, and future directions. PMID:25635490

Updating the Mitochondrial Free Radical Theory of Aging: An Integrated View, Key Aspects, and Confounding Concepts

PubMed Central

2013-01-01

Abstract An updated version of the mitochondrial free radical theory of aging (MFRTA) and longevity is reviewed. Key aspects of the theory are emphasized. Another main focus concerns common misconceptions that can mislead investigators from other specialties, even to wrongly discard the theory. Those different issues include (i) the main reactive oxygen species (ROS)-generating site in the respiratory chain in relation to aging and longevity: complex I; (ii) the close vicinity or even contact between that site and the mitochondrial DNA, in relation to the lack of local efficacy of antioxidants and to sub-cellular compartmentation; (iii) the relationship between mitochondrial ROS production and oxygen consumption; (iv) recent criticisms on the MFRTA; (v) the widespread assumption that ROS are simple “by-products” of the mitochondrial respiratory chain; (vi) the unnecessary postulation of “vicious cycle” hypotheses of mitochondrial ROS generation which are not central to the free radical theory of aging; and (vii) the role of DNA repair concerning endogenous versus exogenous damage. After considering the large body of data already available, two general characteristics responsible for the high maintenance degree of long-lived animals emerge: (i) a low generation rate of endogenous damage: and (ii) the possession of tissue macromolecules that are highly resistant to oxidative modification. Antioxid. Redox Signal. 19, 1420–1445. PMID:23642158

Coordinating Council. Sixth Meeting: Who Are Our Key Users?

NASA Technical Reports Server (NTRS)

1991-01-01

This NASA Scientific and Technical Information Program Coordinating Council meeting deals with the topic 'Who are our key users?' Presentations were made on the following subtopics: Key users: Who uses the system the most, Who orders the most documents, Users: What do we know about them?, NASA/DOD Aerospace Knowledge Diffusion research project on 'Potential key users', How we meet the user's needs, and STI Council user requirements update. Summaries of discussions after the presentations are included along with visuals for the presentations.

Valence-Dependent Belief Updating: Computational Validation.

PubMed

Kuzmanovic, Bojana; Rigoux, Lionel

2017-01-01

People tend to update beliefs about their future outcomes in a valence-dependent way: they are likely to incorporate good news and to neglect bad news. However, belief formation is a complex process which depends not only on motivational factors such as the desire for favorable conclusions, but also on multiple cognitive variables such as prior beliefs, knowledge about personal vulnerabilities and resources, and the size of the probabilities and estimation errors. Thus, we applied computational modeling in order to test for valence-induced biases in updating while formally controlling for relevant cognitive factors. We compared biased and unbiased Bayesian models of belief updating, and specified alternative models based on reinforcement learning. The experiment consisted of 80 trials with 80 different adverse future life events. In each trial, participants estimated the base rate of one of these events and estimated their own risk of experiencing the event before and after being confronted with the actual base rate. Belief updates corresponded to the difference between the two self-risk estimates. Valence-dependent updating was assessed by comparing trials with good news (better-than-expected base rates) with trials with bad news (worse-than-expected base rates). After receiving bad relative to good news, participants' updates were smaller and deviated more strongly from rational Bayesian predictions, indicating a valence-induced bias. Model comparison revealed that the biased (i.e., optimistic) Bayesian model of belief updating better accounted for data than the unbiased (i.e., rational) Bayesian model, confirming that the valence of the new information influenced the amount of updating. Moreover, alternative computational modeling based on reinforcement learning demonstrated higher learning rates for good than for bad news, as well as a moderating role of personal knowledge. Finally, in this specific experimental context, the approach based on reinforcement

Valence-Dependent Belief Updating: Computational Validation

PubMed Central

Kuzmanovic, Bojana; Rigoux, Lionel

2017-01-01

People tend to update beliefs about their future outcomes in a valence-dependent way: they are likely to incorporate good news and to neglect bad news. However, belief formation is a complex process which depends not only on motivational factors such as the desire for favorable conclusions, but also on multiple cognitive variables such as prior beliefs, knowledge about personal vulnerabilities and resources, and the size of the probabilities and estimation errors. Thus, we applied computational modeling in order to test for valence-induced biases in updating while formally controlling for relevant cognitive factors. We compared biased and unbiased Bayesian models of belief updating, and specified alternative models based on reinforcement learning. The experiment consisted of 80 trials with 80 different adverse future life events. In each trial, participants estimated the base rate of one of these events and estimated their own risk of experiencing the event before and after being confronted with the actual base rate. Belief updates corresponded to the difference between the two self-risk estimates. Valence-dependent updating was assessed by comparing trials with good news (better-than-expected base rates) with trials with bad news (worse-than-expected base rates). After receiving bad relative to good news, participants' updates were smaller and deviated more strongly from rational Bayesian predictions, indicating a valence-induced bias. Model comparison revealed that the biased (i.e., optimistic) Bayesian model of belief updating better accounted for data than the unbiased (i.e., rational) Bayesian model, confirming that the valence of the new information influenced the amount of updating. Moreover, alternative computational modeling based on reinforcement learning demonstrated higher learning rates for good than for bad news, as well as a moderating role of personal knowledge. Finally, in this specific experimental context, the approach based on reinforcement

Bilateral comparison of 10 pF and 100 pF standards (ongoing BIPM key comparisons BIPM.EM-K14.a and 14.b) between the NMISA (South Africa) and the BIPM

NASA Astrophysics Data System (ADS)

Gournay, Pierre; Khoza, Michael

2017-01-01

This report presents the results of a bilateral comparison of 10 pF and 100 pF capacitance standards between the NMISA (South Africa) and the BIPM carried out in 2016. The comparison at 10 pF forms part of the ongoing BIPM key comparison BIPM.EM-K14.a and that at 100 pF of the ongoing BIPM key comparison BIPM.EM-K14.b. The BIPM is the pilot laboratory for both of these comparisons. Two 10 pF and 100 pF travelling standards belonging to the BIPM were used in this comparison carried out with an 'A-B-A' pattern of measurements. The standards were measured first at the BIPM for a period of about one month, then for a similar period at the NMISA, and finally again at the BIPM. The measurand was the two terminal-pair capacitance at a frequency of either 1000 Hz or 1592 Hz, for a measuring rms voltage of 15 V at 10 pF and 10 V at 100 pF. One of the 10 pF travelling standards had to be eliminated from the comparison due to a bistable behaviour, possibly due to transportation. The results from the NMISA and the BIPM at both 1000 Hz and 1592 Hz were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95 % confidence, k = 2) of maximum value 0.33 × 10-6 at 10 pF and 0.24 × 10-6 at 100 pF (and 1000 Hz in both cases). Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Update of NDL’s list of key foods based on the 2007-2008 WWEIA-NHANES

USDA-ARS?s Scientific Manuscript database

The Nutrient Data Laboratory is responsible for developing authoritative nutrient databases that contain a wide range of food composition values of the nation's food supply. This requires updating and revising the USDA Nutrient Database for Standard Reference (SR) and developing various special int...

Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, March to April 2011 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Power, O.; Solve, S.; Chayramy, R.; Stock, M.

2011-01-01

As a part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from March to April 2011. Two BIPM Zener diode-based travelling standards (Fluke 732B) were transported by freight to NSAI-NML. At NSAI-NML, the 10 V output EMF of each travelling standard was measured by direct comparison with a group of characterized Zener diode-based electronic voltage standards. At the BIPM, the travelling standards were calibrated before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient pressure. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Key Issues in Hymenoptera Venom Allergy: An Update.

PubMed

Alfaya Arias, T; Soriano Gómis, V; Soto Mera, T; Vega Castro, A; Vega Gutiérrez, J M; Alonso Llamazares, A; Antolín Amérigo, D; Carballada Gonzalez, F J; Dominguez Noche, C; Gutierrez Fernandez, D; Marques Amat, L; Martinez Arcediano, A; Martinez San Ireneo, M; Moreno Ancillo, A; Puente Crespo, Y; Ruiz Leon, B; Sánchez Morillas, L

In this review, the Hymenoptera Allergy Committee of the SEAIC analyzes the most recent scientific literature addressing problems related to the diagnosis of hymenoptera allergy and to management of venom immunotherapy. Molecular diagnosis and molecular risk profiles are the key areas addressed. The appearance of new species of hymenoptera that are potentially allergenic in Spain and the associated diagnostic and therapeutic problems are also described. Finally, we analyze the issue of mast cell activation syndrome closely related to hymenoptera allergy, which has become a new diagnostic challenge for allergists given its high prevalence in patients with venom anaphylaxis.

Automatic background updating for video-based vehicle detection

NASA Astrophysics Data System (ADS)

Hu, Chunhai; Li, Dongmei; Liu, Jichuan

2008-03-01

Video-based vehicle detection is one of the most valuable techniques for the Intelligent Transportation System (ITS). The widely used video-based vehicle detection technique is the background subtraction method. The key problem of this method is how to subtract and update the background effectively. In this paper an efficient background updating scheme based on Zone-Distribution for vehicle detection is proposed to resolve the problems caused by sudden camera perturbation, sudden or gradual illumination change and the sleeping person problem. The proposed scheme is robust and fast enough to satisfy the real-time constraints of vehicle detection.

Updated recommendations: an assessment of NICE clinical guidelines

PubMed Central

2014-01-01

Background Updating is important to ensure clinical guideline (CG) recommendations remain valid. However, little research has been undertaken in this field. We assessed CGs produced by the National Institute for Health and Care Excellence (NICE) to identify and describe updated recommendations and to investigate potential factors associated with updating. Also, we evaluated the reporting and presentation of recommendation changes. Methods We performed a descriptive analysis of original and updated CGs and recommendations, and an assessment of presentation formats and methods for recording information. We conducted a case-control study, defining cases as original recommendations that were updated (‘new-replaced’ recommendations), and controls as original recommendations that were considered to remain valid (‘not changed’ recommendations). We performed a comparison of main characteristics between cases and controls, and we planned a multiple regression analysis to identify potential predictive factors for updating. Results We included nine updated CGs (1,306 recommendations) and their corresponding original versions (1,106 recommendations). Updated CGs included 812 (62%) recommendations ‘not reviewed’, 368 (28.1%) ‘new’ recommendations, 104 (7.9%) ‘amended’ recommendations, and 25 (1.9%) recommendations reviewed but unchanged. The presentation formats used to indicate the changes in recommendations varied widely across CGs. Changes in ‘amended’, ‘deleted’, and ‘new-replaced’ recommendations (n = 296) were reported infrequently, mostly in appendices. These changes were recorded in 167 (56.4%) recommendations; and were explained in 81 (27.4%) recommendations. We retrieved a total of 7.1% (n = 78) case recommendations (‘new-replaced’) and 2.4% (n = 27) control recommendations (‘not changed’) in original CGs. The updates were mainly from ‘Fertility CG’, about ‘gynaecology, pregnancy and birth’ topic, and �

A keyword searchable attribute-based encryption scheme with attribute update for cloud storage.

PubMed

Wang, Shangping; Ye, Jian; Zhang, Yaling

2018-01-01

Ciphertext-policy attribute-based encryption (CP-ABE) scheme is a new type of data encryption primitive, which is very suitable for data cloud storage for its fine-grained access control. Keyword-based searchable encryption scheme enables users to quickly find interesting data stored in the cloud server without revealing any information of the searched keywords. In this work, we provide a keyword searchable attribute-based encryption scheme with attribute update for cloud storage, which is a combination of attribute-based encryption scheme and keyword searchable encryption scheme. The new scheme supports the user's attribute update, especially in our new scheme when a user's attribute need to be updated, only the user's secret key related with the attribute need to be updated, while other user's secret key and the ciphertexts related with this attribute need not to be updated with the help of the cloud server. In addition, we outsource the operation with high computation cost to cloud server to reduce the user's computational burden. Moreover, our scheme is proven to be semantic security against chosen ciphertext-policy and chosen plaintext attack in the general bilinear group model. And our scheme is also proven to be semantic security against chosen keyword attack under bilinear Diffie-Hellman (BDH) assumption.

A keyword searchable attribute-based encryption scheme with attribute update for cloud storage

PubMed Central

Wang, Shangping; Zhang, Yaling

2018-01-01

Ciphertext-policy attribute-based encryption (CP-ABE) scheme is a new type of data encryption primitive, which is very suitable for data cloud storage for its fine-grained access control. Keyword-based searchable encryption scheme enables users to quickly find interesting data stored in the cloud server without revealing any information of the searched keywords. In this work, we provide a keyword searchable attribute-based encryption scheme with attribute update for cloud storage, which is a combination of attribute-based encryption scheme and keyword searchable encryption scheme. The new scheme supports the user's attribute update, especially in our new scheme when a user's attribute need to be updated, only the user's secret key related with the attribute need to be updated, while other user's secret key and the ciphertexts related with this attribute need not to be updated with the help of the cloud server. In addition, we outsource the operation with high computation cost to cloud server to reduce the user's computational burden. Moreover, our scheme is proven to be semantic security against chosen ciphertext-policy and chosen plaintext attack in the general bilinear group model. And our scheme is also proven to be semantic security against chosen keyword attack under bilinear Diffie-Hellman (BDH) assumption. PMID:29795577

Visualizing the Impact of Art: An Update and Comparison of Current Psychological Models of Art Experience

PubMed Central

Pelowski, Matthew; Markey, Patrick S.; Lauring, Jon O.; Leder, Helmut

2016-01-01

The last decade has witnessed a renaissance of empirical and psychological approaches to art study, especially regarding cognitive models of art processing experience. This new emphasis on modeling has often become the basis for our theoretical understanding of human interaction with art. Models also often define areas of focus and hypotheses for new empirical research, and are increasingly important for connecting psychological theory to discussions of the brain. However, models are often made by different researchers, with quite different emphases or visual styles. Inputs and psychological outcomes may be differently considered, or can be under-reported with regards to key functional components. Thus, we may lose the major theoretical improvements and ability for comparison that can be had with models. To begin addressing this, this paper presents a theoretical assessment, comparison, and new articulation of a selection of key contemporary cognitive or information-processing-based approaches detailing the mechanisms underlying the viewing of art. We review six major models in contemporary psychological aesthetics. We in turn present redesigns of these models using a unified visual form, in some cases making additions or creating new models where none had previously existed. We also frame these approaches in respect to their targeted outputs (e.g., emotion, appraisal, physiological reaction) and their strengths within a more general framework of early, intermediate, and later processing stages. This is used as a basis for general comparison and discussion of implications and future directions for modeling, and for theoretically understanding our engagement with visual art. PMID:27199697

Visualizing the Impact of Art: An Update and Comparison of Current Psychological Models of Art Experience.

PubMed

Pelowski, Matthew; Markey, Patrick S; Lauring, Jon O; Leder, Helmut

2016-01-01

The last decade has witnessed a renaissance of empirical and psychological approaches to art study, especially regarding cognitive models of art processing experience. This new emphasis on modeling has often become the basis for our theoretical understanding of human interaction with art. Models also often define areas of focus and hypotheses for new empirical research, and are increasingly important for connecting psychological theory to discussions of the brain. However, models are often made by different researchers, with quite different emphases or visual styles. Inputs and psychological outcomes may be differently considered, or can be under-reported with regards to key functional components. Thus, we may lose the major theoretical improvements and ability for comparison that can be had with models. To begin addressing this, this paper presents a theoretical assessment, comparison, and new articulation of a selection of key contemporary cognitive or information-processing-based approaches detailing the mechanisms underlying the viewing of art. We review six major models in contemporary psychological aesthetics. We in turn present redesigns of these models using a unified visual form, in some cases making additions or creating new models where none had previously existed. We also frame these approaches in respect to their targeted outputs (e.g., emotion, appraisal, physiological reaction) and their strengths within a more general framework of early, intermediate, and later processing stages. This is used as a basis for general comparison and discussion of implications and future directions for modeling, and for theoretically understanding our engagement with visual art.

Key Stage 4 and GCSE: An Update from the Association's Key Stage 4 Working Group.

ERIC Educational Resources Information Center

Davies, Peter

1991-01-01

Examines plans and proposals for the "Key Stage 4" portion of the United Kingdom's General Certificate for Secondary Education (GCSE) program. Explains the development of a 10-point assessment scale and plans for combined subject courses. Argues that, although economics instruction should be encouraged, it should not be the sole emphasis…

Location-Aware Dynamic Session-Key Management for Grid-Based Wireless Sensor Networks

PubMed Central

Chen, Chin-Ling; Lin, I-Hsien

2010-01-01

Security is a critical issue for sensor networks used in hostile environments. When wireless sensor nodes in a wireless sensor network are distributed in an insecure hostile environment, the sensor nodes must be protected: a secret key must be used to protect the nodes transmitting messages. If the nodes are not protected and become compromised, many types of attacks against the network may result. Such is the case with existing schemes, which are vulnerable to attacks because they mostly provide a hop-by-hop paradigm, which is insufficient to defend against known attacks. We propose a location-aware dynamic session-key management protocol for grid-based wireless sensor networks. The proposed protocol improves the security of a secret key. The proposed scheme also includes a key that is dynamically updated. This dynamic update can lower the probability of the key being guessed correctly. Thus currently known attacks can be defended. By utilizing the local information, the proposed scheme can also limit the flooding region in order to reduce the energy that is consumed in discovering routing paths. PMID:22163606

Location-aware dynamic session-key management for grid-based Wireless Sensor Networks.

PubMed

Chen, Chin-Ling; Lin, I-Hsien

2010-01-01

Security is a critical issue for sensor networks used in hostile environments. When wireless sensor nodes in a wireless sensor network are distributed in an insecure hostile environment, the sensor nodes must be protected: a secret key must be used to protect the nodes transmitting messages. If the nodes are not protected and become compromised, many types of attacks against the network may result. Such is the case with existing schemes, which are vulnerable to attacks because they mostly provide a hop-by-hop paradigm, which is insufficient to defend against known attacks. We propose a location-aware dynamic session-key management protocol for grid-based wireless sensor networks. The proposed protocol improves the security of a secret key. The proposed scheme also includes a key that is dynamically updated. This dynamic update can lower the probability of the key being guessed correctly. Thus currently known attacks can be defended. By utilizing the local information, the proposed scheme can also limit the flooding region in order to reduce the energy that is consumed in discovering routing paths.

Final report on key comparison CCAUV.A-K5: pressure calibration of laboratory standard microphones in the frequency range 2 Hz to 10 kHz

NASA Astrophysics Data System (ADS)

Avison, Janine; Barham, Richard

2014-01-01

This document and the accompanying spreadsheets constitute the final report for key comparison CCAUV.A-K5 on the pressure calibration of laboratory standard microphones in the frequency range from 2 Hz to 10 kHz. Twelve national measurement institutes took part in the key comparison and the National Physical Laboratory piloted the project. Two laboratory standard microphones IEC type LS1P were circulated to the participants and results in the form of regular calibration certificates were collected throughout the project. One of the microphones was subsequently deemed to have compromised stability for the purpose of deriving a reference value. Consequently the key comparison reference value (KCRV) has been made based on the weighted mean results for sensitivity level and for sensitivity phase from just one of the microphones. Corresponding degrees of equivalence (DoEs) have also been calculated and are presented. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Quantum key distribution with finite resources: Secret key rates via Renyi entropies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abruzzo, Silvestre; Kampermann, Hermann; Mertz, Markus

A realistic quantum key distribution (QKD) protocol necessarily deals with finite resources, such as the number of signals exchanged by the two parties. We derive a bound on the secret key rate which is expressed as an optimization problem over Renyi entropies. Under the assumption of collective attacks by an eavesdropper, a computable estimate of our bound for the six-state protocol is provided. This bound leads to improved key rates in comparison to previous results.

Report of the key-comparison of spectral diffuse reflectance (EURAMET.PR-K5) (Ref. 619)

NASA Astrophysics Data System (ADS)

Andor, György; Gál, Péter

2018-01-01

This report details the final results of the EURAMET comparison on regular spectral transmittance carried out between 2006 and 2016. The aim of this comparison was to check the agreement of measurement of the spectral diffuse reflectance among participants, using the measurement geometry of d/0 or 0/d in the wavelength range of 360 nm to 780 nm at 20 nm increment. We used a star type comparison: first the participants sent their samples to the pilot, than the pilot measured all the samples of the participants and sent them back. The participants measured the samples and sent them to the pilot for control measurement. Six standards were used as reference standards in order to maintain the scale during the comparison. These were three samples of BCR-406 opal glasses (BCR 30506; BCR 30303; BCR 30704), an MC20 Russian opal glass (MC 4777) and two samples made of pressed halon (polytetrafluoroethylene) powder (halon 2007A; halon 2007C). These six samples were designated as the Comparison reference standards. The diffuse reflectance was initially measured on the OMH (BFKH) absolute reflectometer. The link to the CCPR-K5 results was BFKH, and the check on BFKH was the PTB results who also participated in the CCPR-K5 comparison. The participants were GUM, INM, LNE, METAS, BFKH, PTB, SP. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCPR, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: Final report on CCQM-K44: Trace elements in sewage sludge

NASA Astrophysics Data System (ADS)

Aregbe, Y.; Taylor, P. D. P.

2009-01-01

CCQM-K44 was an activity of the Inorganic Analysis Working Group (IAWG) of CCQM and was coordinated by the Joint Research Centre-Institute for Reference Materials and Measurements (IRMM, Geel, Belgium) of the European Commission (EC). In CCQM-K44 the amount contents of Cd, Cr, Cu, Pb, Hg, Ni and Zn in sewage sludge were the measurands under investigation. Results were reported by six national metrology institutes (NMIs). During the CCQM-IAWG Spring meeting in Paris, April 2006, the approaches to calculate the KCRV as proposed by the coordinating laboratory were discussed and agreed on. The final report was submitted in June 2006. After the final report had been submitted to the CCQM in June 2006 the coordinating laboratory was informed that MIRS/IJS was not a designated institute and therefore could not represent the Slovenian NMI in CCQM-K44. This was contrary to what MIRS confirmed to the coordinating laboratory at the beginning of CCQM-K44. After several discussions between MIRS and the CCQM the coordinating laboratory was asked to amend the final report accordingly. In this revised version of the CCQM-K44 final report the results of MIRS/IJS were taken out of CCQM-K44 and included in the pilot study CCQM-P70, which was organised in parallel to CCQM-K44. Due to the limited number of participants compared to previous key comparisons the mixture model median (MM-median) of all reported results could not be applied as KCRV for all the measurands. During the CCQM-IAWG Spring meeting in Paris, April 2006, the approaches to calculate the KCRV as proposed by the coordinating laboratory were discussed and first agreed on. As a result the final report and degrees of equivalence were finalised and submitted to the CCQM. Subsequent discussions between the IAWG and the CCQM were held, resulting in a different approach as proposed by the coordinating laboratory. Particularly Maurice Cox from NPL recommended the weighted mean and its standard uncertainty (k = 1) as KCRV

Summary of Expansions, Updates, and Results in GREET 2017 Suite of Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Michael; Elgowainy, Amgad; Han, Jeongwoo

This report provides a technical summary of the expansions and updates to the 2017 release of Argonne National Laboratory’s Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET®) model, including references and links to key technical documents related to these expansions and updates. The GREET 2017 release includes an updated version of the GREET1 (the fuel-cycle GREET model) and GREET2 (the vehicle-cycle GREET model), both in the Microsoft Excel platform and in the GREET.net modeling platform. Figure 1 shows the structure of the GREET Excel modeling platform. The .net platform integrates all GREET modules together seamlessly.

CCQM-K104 key comparison (avermectin B1a) on the characterization of organic substances for chemical purity

NASA Astrophysics Data System (ADS)

Dai, Xinhua; Zhang, Wei; Li, Hongmei; Huang, Ting; Li, Mengwan; Quan, Can; Zhang, Qinghe; Davies, Stephen R.; Warren, John; Lo, Man-fung; Kakoulides, Elias; Ceyhan Gören, Ahmet; Marbumrung, Sornkrit; Pfeifer, Dietmar; Ün, İlker; Gündüz, Simay; Yilmaz, Hasibe; Kankaew, Pornhatai; Sudsiri, Nittaya; Shearman, Kittiya; Pookrod, Preeyaporn; Polzer, Joachim; Radeck, Wolfgang

2017-01-01

Under the Comité Consultatif pour la Quantité de Matière (CCQM), a key comparison, CCQM-K104, was coordinated by the National Institute of Metrology (NIM). The comparison was designed to demonstrate a laboratory's performance in determining the mass fraction of the main component in a complex high purity organic material. Nine NMIs or DIs participated in the comparison. Eight participants reported their results. An additional impurity was resolved from the avermectin B1a peak and was tentatively identified as an unknown impurity by NMIA (National Measurement Institute (Australia)). It was subsequently identified by NIM as a diastereoisomer of avermectin B1a at the C-26 position. Final reference value (KCRV) = 924.63 mg/g, with uncertainty (k=1) = 3.89 mg/g, and expanded uncertainty = 8.97 mg/g. The degrees of equivalence with the avermectin B1a KCRV for each participant were reported. The measurement results and degrees of equivalence should be indicative of the performance of a laboratory's measurement capability for the purity assignment of organic compounds of high structural complexity (relative molecular mass range of 500 Da -1000 Da and low polarity (-log KOW <= -2). Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

KEY COMPARISON: CCQM-K28: Tributyltin in sediment

NASA Astrophysics Data System (ADS)

Wolff Briche, Céline S. J.; Wahlen, Raimund; Sturgeon, Ralph E.

2006-01-01

Key comparison CCQM K-28 was undertaken to assess the measurement capabilities for quantitation of (C4H9)3Sn+ (TBT) in a prepared marine sediment by National Metrology Institutes (NMIs), which are members of the Comité Consultatif pour la Quantité de Matière (CCQM). It follows a previous pilot study, CCQM-P18. [1, 2] This exercise was sanctioned by the 8th CCQM meeting, 18-19 April 2002, as an activity of the Inorganic Analysis Working Group and was jointly coordinated by the Institute for National Measurement Standards of the National Research Council of Canada (NRC) and LGC, UK. Eight NMIs initially indicated their interest, with seven ultimately submitting their results. All NMIs relied on isotope dilution mass spectrometry using a species-specific 117Sn-enriched TBT standard, which was supplied by LGC. No analytical methodology was prescribed for this study. As a result, a variety of extraction approaches was adopted by the participants, including mechanical shaking, sonication, accelerated solvent extraction, microwave assisted extraction and heating in combination with ethylation and direct sampling. Detection techniques included ICP-MS (coupled to GC or HPLC for the separation of Sn species) and GC-MS. Main text. To reach the main text of this paper, click on Final Report. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the Mutual Recognition Arrangement (MRA).

Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the SMD (Belgium) and the BIPM

NASA Astrophysics Data System (ADS)

Rolland, Benjamin; Fletcher, Nick; Vlad, Dana

2017-01-01

This report gives the result of a bilateral comparison of resistance between the SMD (Belgium) and the BIPM carried out in 2017. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the SMD, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13.b (for 10 kΩ). The results from the SMD and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 0.080 × 10-6 for 1 Ω and 0.068 × 10-6 for 10 kΩ. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the NIMT (Thailand) and the BIPM

NASA Astrophysics Data System (ADS)

Rolland, B.; Fletcher, N.; Khumthukthit, N.; Jassadajin, C.

2017-01-01

This report gives the result of a bilateral comparison of resistance between the NIMT (Thailand) and the BIPM carried out in 2015. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the BIM, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13b (for 10 kΩ). The results from the NIMT and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 0.20 × 10-6 for 1 Ω and 0.74 × 10-6 for 10 kΩ. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Crucial role of strategy updating for coexistence of strategies in interaction networks.

PubMed

Zhang, Jianlei; Zhang, Chunyan; Cao, Ming; Weissing, Franz J

2015-04-01

Network models are useful tools for studying the dynamics of social interactions in a structured population. After a round of interactions with the players in their local neighborhood, players update their strategy based on the comparison of their own payoff with the payoff of one of their neighbors. Here we show that the assumptions made on strategy updating are of crucial importance for the strategy dynamics. In the first step, we demonstrate that seemingly small deviations from the standard assumptions on updating have major implications for the evolutionary outcome of two cooperation games: cooperation can more easily persist in a Prisoner's Dilemma game, while it can go more easily extinct in a Snowdrift game. To explain these outcomes, we develop a general model for the updating of states in a network that allows us to derive conditions for the steady-state coexistence of states (or strategies). The analysis reveals that coexistence crucially depends on the number of agents consulted for updating. We conclude that updating rules are as important for evolution on a network as network structure and the nature of the interaction.

Crucial role of strategy updating for coexistence of strategies in interaction networks

NASA Astrophysics Data System (ADS)

Zhang, Jianlei; Zhang, Chunyan; Cao, Ming; Weissing, Franz J.

2015-04-01

Network models are useful tools for studying the dynamics of social interactions in a structured population. After a round of interactions with the players in their local neighborhood, players update their strategy based on the comparison of their own payoff with the payoff of one of their neighbors. Here we show that the assumptions made on strategy updating are of crucial importance for the strategy dynamics. In the first step, we demonstrate that seemingly small deviations from the standard assumptions on updating have major implications for the evolutionary outcome of two cooperation games: cooperation can more easily persist in a Prisoner's Dilemma game, while it can go more easily extinct in a Snowdrift game. To explain these outcomes, we develop a general model for the updating of states in a network that allows us to derive conditions for the steady-state coexistence of states (or strategies). The analysis reveals that coexistence crucially depends on the number of agents consulted for updating. We conclude that updating rules are as important for evolution on a network as network structure and the nature of the interaction.

Key comparison BIPM.RI(I)-K5 of the air-kerma standards of the SMU, Slovakia and the BIPM in 137Cs gamma radiation

NASA Astrophysics Data System (ADS)

Kessler, C.; Burns, D.; Durný, N.

2018-01-01

The first direct comparison of the standards for air kerma of the Slovak Institute of Metrology (SMU), Slovakia and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 137Cs radiation beam of the BIPM in June 2017. The comparison result, evaluated as a ratio of the SMU and the BIPM standards for air kerma, is 1.0051 with a combined standard uncertainty of 2.7 × 10-3. The results for an indirect comparison made at the same time are consistent with the direct results at the level of 2 parts in 104. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Key comparison BIPM.RI(I)-K1 of the air-kerma standards of the MKEH, Hungary and the BIPM in 60Co gamma radiation

NASA Astrophysics Data System (ADS)

Kessler, C.; Burns, D.; Machula, G.

2018-01-01

A comparison of the standards for air kerma of the Hungarian Trade Licensing Office (MKEH), Hungary and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 60Co radiation beam of the BIPM in March 2016. The comparison result, evaluated as a ratio of the MKEH and the BIPM standards for air kerma, is 1.0047 with a combined standard uncertainty of 1.9 × 10-3. The results for an indirect comparison made at the same time are consistent with the direct results at the level of 2.6 parts in 103. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

United States Department of Education Update, December 2004

ERIC Educational Resources Information Center

Linton, John

2004-01-01

In this update, Linton reports on Congressional filing of a number of bills that involve the topic of prisoner reentry. In addition, he presents a key section of Attorney General John Ashcroft's address (Cleveland, Ohio, September 2004) on prisoner reentry. In this speech, Ashcroft called for a concerted effort to managing a balanced approach:…

KEY COMPARISON: Final report on CCPR K1-a: Spectral irradiance from 250 nm to 2500 nm

NASA Astrophysics Data System (ADS)

Woolliams, Emma R.; Fox, Nigel P.; Cox, Maurice G.; Harris, Peter M.; Harrison, Neil J.

2006-01-01

The CCPR K1-a key comparison of spectral irradiance (from 250 nm to 2500 nm) was carried out to meet the requirements of the Mutual Recognition Arrangement by 13 participating national metrology institutes (NMIs). Because of the fragile nature of the tungsten halogen lamps used as comparison artefacts, the comparison was arranged as a star comparison with three lamps per participant. NPL (United Kingdom) piloted the comparison and, by measuring all lamps, provided a link between participants' measurements. The other participants were BNM-INM (France), CENAM (Mexico), CSIRO (Australia), HUT (Finland), IFA-CSIC (Spain), MSL-IRL (New Zealand), NIM (China), NIST (United States of America), NMIJ (Japan), NRC (Canada), PTB (Germany) and VNIIOFI (Russian Federation). Before the analysis was completed and the results known, the pilot discussed with each participant which lamp measurements should be included as representative of their comparison. As a consequence of this check, at least one measurement was excluded from one third of the lamps because of changes due to transportations. The comparison thus highlighted the difficulty regarding the availability of suitable transfer standards for the dissemination of spectral irradiance. The use of multiple lamps and multiple measurements ensured sufficient redundancy that all participants were adequately represented. In addition, during this pre-draft A phase all participants had the opportunity to review the uncertainty budgets and methods of all other participants. This new process helped to ensure that all submitted results and their associated uncertainties were evaluated in a consistent manner. The comparison was analysed using a model-based method which regarded each lamp as having a stable spectral irradiance and the measurements made by an NMI as systematically influenced by a factor that applies to all that NMI's measurements. The aim of the analysis was to estimate the systematic factor for each NMI. Across the

Key comparison BIPM.RI(I)-K5 of the air kerma standards of the ININ, Mexico and the BIPM in 137Cs gamma radiation

NASA Astrophysics Data System (ADS)

Kessler, C.; Burns, D. T.; Alvarez Romero, J. T.; De la Cruz Hernández, D.; Cabrera Vertti, M. R.; Tovar-Muñoz, V. M.

2015-01-01

A direct comparison of the standards for air kerma of the Instituto Nacional de Investigaciones Nucleares (ININ), Mexico, and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 137Cs radiation beam of the BIPM in February 2015. The comparison result, evaluated as a ratio of the ININ and the BIPM standards for air kerma, is 1.0048 with a combined standard uncertainty of 2.0 × 10-3. The results are analysed and presented in terms of degrees of equivalence for entry in the BIPM key comparison database. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the CMI (Czech Republic) and the BIPM

NASA Astrophysics Data System (ADS)

Rolland, B.; Fletcher, N.; Kučera, J.; Chrobok, P.; Vo&jacute; čko&vacute; , L.

2017-01-01

This report gives the result of a bilateral comparison of resistance between the CMI (Czech Republic) and the BIPM carried out in 2015. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the BIM, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13b (for 10 kΩ). The results from the CMI and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 0.046 × 10-6 for 1 Ω and 0.034 × 10-6 for 10 kΩ. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the NSAI NML (Ireland) and the BIPM

NASA Astrophysics Data System (ADS)

Rolland, B.; Fletcher, N.; Power, O.

2017-01-01

This report gives the result of a bilateral comparison of resistance between the NSAI NML (Ireland) and the BIPM carried out in 2014-2015. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the NSAI-NML, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13b (for 10 kΩ). The results from the NSAI NML and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainties (95% confidence, k = 2) of 0.16 × 10-6 for 1 Ω and 0.42 × 10-6 for 10 kΩ. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 1 Ω and 10 kΩ standards (ongoing BIPM key comparisons BIPM.EM-K13.a and 13.b) between the BIM (Bulgaria) and the BIPM

NASA Astrophysics Data System (ADS)

Rolland, B.; Fletcher, N.; Tenev, A.; Hadzhistoykova, R.

2017-01-01

This report gives the result of a bilateral comparison of resistance between the BIM (Bulgaria) and the BIPM carried out in 2013. Two 1 Ω and two 10 kΩ travelling standards belonging to the BIPM were used. The comparison was carried out with an 'A-B-A' pattern of measurements; the standards were measured first at the BIPM for a period of about one month, then for a similar period at the BIM, and finally again at the BIPM. The measurand was the 4 terminal dc resistance at low power. The BIPM was the pilot laboratory, and the comparison forms part of the ongoing BIPM key comparisons BIPM.EM-K13.a (for 1 Ω) and BIPM.EM-K13b (for 10 kΩ). The results from the BIM and the BIPM were found to be in good agreement, with a difference smaller than the relative expanded uncertainty (95% confidence, k = 2) of 0.30 × 10-6 at 10 kΩ and in reasonable agreement for 1 Ω with a relative difference of -0.18 × 10-6 with a relative expanded uncertainty of 0.17 × 10-6. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Characteristics of precision 1 Ω standard resistors influencing transport behaviour and the uncertainty of key comparisons

NASA Astrophysics Data System (ADS)

Jones, G. R.; Pritchard, B. J.; Elmquist, R. E.

2009-10-01

National measurement institutes (NMIs) participate in international key comparisons organized by the Bureau International des Poids et Mesures (BIPM), the Regional Metrology Organizations (RMOs) or the Consultative Committees of the Comité International des Poids et Mesures (CIPM) in order to provide evidence of equivalent reference standards and measurement capabilities. The US National Institute of Standards and Technology (NIST) and the National Measurement Institute of Australia (NMIA) have recently examined power loading and several other influences on the value of precision transportable 1 Ω resistors that can increase the uncertainty of key comparisons. We have studied the effects of temperature, barometric pressure, humidity, power loading and heat dissipation in oil on transportable wire-wound 1 Ω resistance standards that are based on different alloys and construction principles. This work focuses on standards manufactured from 1970 through 2000 by the NMIA made of Evanohm alloy and on Thomas-type resistors designed in the 1930s and made of Manganin alloy. We show that the relative standard uncertainty related to transport can be less than 0.01 μΩ Ω-1 when using certain resistors of these two types that are characterized and selected for stability. We describe the characterization process, and relate the environmental influences to the physical design, as well as to the mechanical properties and condition of the standards.

Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, March 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Power, O.; Stock, M.

2014-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out in February and March 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_4 (Z4) and BIPM_5 (Z5), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 10 March 2014. UNML - UBIPM = -0.64 µV uc = 1.35 µV, at 10 V where uc is thecombined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML,based on KJ-90, and the uncertainty related to the comparison. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated standard uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to

Final report on key comparison APMP.M.P-K3: Absolute pressure measurements in gas from 3 × 10-6 Pa to 9 × 10-4 Pa

NASA Astrophysics Data System (ADS)

Yoshida, H.; Arai, K.; Akimichi, H.; Hong, S. S.; Song, H. W.

2011-01-01

The results of a key comparison of ultra-high vacuum standards at two national metrology institutes (NMIJ/AIST and KRISS) are reported. This bilateral comparison was carried out from May 2010 to October 2010 within the framework of the Asia-Pacific Metrology Programme (APMP) to determine their degrees of equivalence at pressures in the range from 3 × 10-6 Pa to 9 × 10-4 Pa. The pilot institute was NMIJ/AIST. Two spinning rotor gauges and two hot cathode ionization gauges were used as the transfer standards. NMIJ/AIST used two calibration systems: the dynamic expansion system (NMIJ-DES) and two-stage flow-dividing system (NMIJ-TFS). KRISS used the dynamic expansion system. The transfer standards were sufficiently stable to meet the requirements of the comparison compared with those of previous international comparisons owing to some improvements of the protocol and the transfer standards. The ultra-high vacuum standards of NMIJ/AIST and KRISS were found to be equivalent within their claimed uncertainties in the range from 3 × 10-6 Pa to 9 × 10-5 Pa. The NMIJ-DES results, which have smaller uncertainty than NMIJ-TFS, were transferred to the corresponding CCM key comparison, CCM.P-K3, in the range from 3 × 10-6 Pa to 9 × 10-5 Pa and it is shown that the NMIJ values were equivalent to the CCM key comparison reference value within the claimed uncertainties. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Guideline on terminology and definitions of updating clinical guidelines: The Updating Glossary.

PubMed

Martínez García, Laura; Pardo-Hernández, Hector; Sanabria, Andrea Juliana; Alonso-Coello, Pablo; Penman, Katrina; McFarlane, Emma

2018-03-01

The Guidelines International Network (G-I-N) Updating Guidelines Working Group launched an initiative to develop a glossary (the Updating Glossary) with domains, terms, definitions, and synonyms related to updating of clinical guidelines (CGs). The steering committee developed an initial list of domains, terms, definitions, and synonyms through brainstorming and discussion. The panel members participated in three rounds of feedback to discuss, refine, and clarify the proposed terms, definitions, and synonyms. Finally, the panel members were surveyed to assess their level of agreement regarding the glossary. Eighteen terms were identified and defined: (1) continuous updating, (2) decision to update, (3) fixed updating, (4) full updating, (5) impact of the new evidence, (6) partial updating, (7) prioritization process, (8) reporting process, (9) signal for an update, (10) surveillance process, (11) time of validity, (12) timeframe, (13) tools and resources, (14) up to date, (15) update cycle, (16) update unit, (17) updated version, and (18) updating strategy. Consensus was reached for all terms, definitions, and synonyms (median agreement scores ≥ 6); except for one term. The G-I-N Updating Guidelines Working Group assembled the Updating Glossary to facilitate and improve the knowledge exchange among CGs developers, researchers, and users. Copyright © 2017 Elsevier Inc. All rights reserved.

Design of Firmware Update Strategy in Tower Mounted Amplifier

NASA Astrophysics Data System (ADS)

Lv, Yi; Han, Shuqin

With rapid development of radio communication, Tower mounted amplifier (TMA) that conform to AISG protocol will be increasingly applied. Remote firmware update function is essential for TMA. In this paper, a method about remote firmware update that conforms to AISG2.0 is proposed. In this paper, defect of traditional firmware storage is given, and the implementation procedure of firmware storing that based on internal flash of STR755 was introduced. According to corresponding specification in aisg2.0, the process of firmware download and activation are provided in detail. The key point of bootloader was given. Application result shows that the strategy is reliable and highly secure.

KEY COMPARISON: CCQM-K61: Quantitation of a linearised plasmid DNA, based on a matched standard in a matrix of non-target DNA

NASA Astrophysics Data System (ADS)

Woolford, Alison; Holden, Marcia; Salit, Marc; Burns, Malcolm; Ellison, Stephen L. R.

2009-01-01

Key comparison CCQM-K61 was performed to demonstrate and document the capability of interested national metrology institutes in the determination of the quantity of specific DNA target in an aqueous solution. The study provides support for the following measurement claim: "Quantitation of a linearised plasmid DNA, based on a matched standard in a matrix of non-target DNA". The comparison was an activity of the Bioanalysis Working Group (BAWG) of the Comité Consultatif pour la Quantité de Matière and was coordinated by NIST (Gaithersburg, USA) and LGC (Teddington, UK). The following laboratories (in alphabetical order) participated in this key comparison. DMSC (Thailand); IRMM (European Union); KRISS (Republic of Korea); LGC (UK); NIM (China); NIST (USA); NMIA (Australia); NMIJ (Japan); VNIIM (Russian Federation) Good agreement was observed between the reported results of all nine of the participants. Uncertainty estimates did not account fully for the dispersion of results even after allowance for possible inhomogeneity in calibration materials. Preliminary studies suggest that the effects of fluorescence threshold setting might contribute to the excess dispersion, and further study of this topic is suggested Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Updating Human Factors Engineering Guidelines for Conducting Safety Reviews of Nuclear Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

O, J.M.; Higgins, J.; Stephen Fleger - NRC

The U.S. Nuclear Regulatory Commission (NRC) reviews the human factors engineering (HFE) programs of applicants for nuclear power plant construction permits, operating licenses, standard design certifications, and combined operating licenses. The purpose of these safety reviews is to help ensure that personnel performance and reliability are appropriately supported. Detailed design review procedures and guidance for the evaluations is provided in three key documents: the Standard Review Plan (NUREG-0800), the HFE Program Review Model (NUREG-0711), and the Human-System Interface Design Review Guidelines (NUREG-0700). These documents were last revised in 2007, 2004 and 2002, respectively. The NRC is committed to the periodicmore » update and improvement of the guidance to ensure that it remains a state-of-the-art design evaluation tool. To this end, the NRC is updating its guidance to stay current with recent research on human performance, advances in HFE methods and tools, and new technology being employed in plant and control room design. This paper describes the role of HFE guidelines in the safety review process and the content of the key HFE guidelines used. Then we will present the methodology used to develop HFE guidance and update these documents, and describe the current status of the update program.« less

Continuously updated network meta-analysis and statistical monitoring for timely decision-making

PubMed Central

Nikolakopoulou, Adriani; Mavridis, Dimitris; Egger, Matthias; Salanti, Georgia

2016-01-01

Pairwise and network meta-analysis (NMA) are traditionally used retrospectively to assess existing evidence. However, the current evidence often undergoes several updates as new studies become available. In each update recommendations about the conclusiveness of the evidence and the need of future studies need to be made. In the context of prospective meta-analysis future studies are planned as part of the accumulation of the evidence. In this setting, multiple testing issues need to be taken into account when the meta-analysis results are interpreted. We extend ideas of sequential monitoring of meta-analysis to provide a methodological framework for updating NMAs. Based on the z-score for each network estimate (the ratio of effect size to its standard error) and the respective information gained after each study enters NMA we construct efficacy and futility stopping boundaries. A NMA treatment effect is considered conclusive when it crosses an appended stopping boundary. The methods are illustrated using a recently published NMA where we show that evidence about a particular comparison can become conclusive via indirect evidence even if no further trials address this comparison. PMID:27587588

On-site comparison of Quantum Hall Effect resistance standards of METAS and the BIPM: Ongoing key comparison BIPM.EM-K12

NASA Astrophysics Data System (ADS)

Gournay, Pierre; Rolland, Benjamin; Mortara, Alessandro; Jeanneret, Blaise

2018-01-01

An on-site comparison of the quantum Hall effect (QHE) resistance standards of the Federal Institute of Metrology METAS (Switzerland) and of the Bureau International des Poids et Mesures (BIPM) was made in December 2017. Measurements of a 100 Ω standard in terms of the conventional value of the von Klitzing constant, RK-90, agreed to 5 parts in 1010 with a relative combined standard uncertainty uc = 23 × 10‑10. Scaling from 100 Ω to 10 kΩ has also been addressed through the measurement of a 10000 Ω/100 Ω ratio. The measurements carried out agreed to 2 parts in 1010 with a relative combined standard uncertainty uc = 19 × 10‑10. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Dali server update.

PubMed

Holm, Liisa; Laakso, Laura M

2016-07-08

The Dali server (http://ekhidna2.biocenter.helsinki.fi/dali) is a network service for comparing protein structures in 3D. In favourable cases, comparing 3D structures may reveal biologically interesting similarities that are not detectable by comparing sequences. The Dali server has been running in various places for over 20 years and is used routinely by crystallographers on newly solved structures. The latest update of the server provides enhanced analytics for the study of sequence and structure conservation. The server performs three types of structure comparisons: (i) Protein Data Bank (PDB) search compares one query structure against those in the PDB and returns a list of similar structures; (ii) pairwise comparison compares one query structure against a list of structures specified by the user; and (iii) all against all structure comparison returns a structural similarity matrix, a dendrogram and a multidimensional scaling projection of a set of structures specified by the user. Structural superimpositions are visualized using the Java-free WebGL viewer PV. The structural alignment view is enhanced by sequence similarity searches against Uniprot. The combined structure-sequence alignment information is compressed to a stack of aligned sequence logos. In the stack, each structure is structurally aligned to the query protein and represented by a sequence logo. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Update on women in physics in Argentina

NASA Astrophysics Data System (ADS)

Brudny, Vera; Lagorio, Cecilia; Frechero, Marisa; Tamarit, Francisco

2013-03-01

Data collected 10 years ago in Argentina concluded that women in physics were underrepresented in many instances and that a "crystal ceiling" was firmly in place. We have collected updated data for several indicators and compared them with those obtained 10 years ago. Although there is not a clear conclusion to be drawn from this comparison, we try to explain the results within the framework of the changes in scientific policies in Argentina.

Authentication and Key Establishment in Dynamic Wireless Sensor Networks

PubMed Central

Qiu, Ying; Zhou, Jianying; Baek, Joonsang; Lopez, Javier

2010-01-01

When a sensor node roams within a very large and distributed wireless sensor network, which consists of numerous sensor nodes, its routing path and neighborhood keep changing. In order to provide a high level of security in this environment, the moving sensor node needs to be authenticated to new neighboring nodes and a key established for secure communication. The paper proposes an efficient and scalable protocol to establish and update the authentication key in a dynamic wireless sensor network environment. The protocol guarantees that two sensor nodes share at least one key with probability 1 (100%) with less memory and energy cost, while not causing considerable communication overhead. PMID:22319321

KEY COMPARISON: EUROMET.M.D-K4/EUROMET Project 702: Comparison of the calibrations of high-resolution hydrometers for liquid density determinations

NASA Astrophysics Data System (ADS)

Lorefice, S.; Malengo, A.; Vámossy, C.; Bettin, H.; Toth, H.; do Céu Ferreira, M.; Gosset, A.; Madec, T.; Heinonen, M.; Buchner, C.; Lenard, E.; Spurny, R.; Akcadag, U.; Domostroeva, N.

2008-01-01

The main objective of the EUROMET project 702 was to compare the extent of comparability among eleven participating European national metrology institutes (INRIM (IT), OMH (HU), PTB (DE), BEV (AT), IPQ (PT), LNE (FR), MIKES (FI), GUM (PL), SMU (SK), UME (TR) and VNIIM (RU)) in performing calibrations of high-resolution hydrometers for liquid density determination in the range between 600 kg m-3 and 1300 kg m-3. By means of two groups of four similar transfer standards of excellent metrological characteristics, the participating laboratories were initially divided into two groups (petals) linked by the three density laboratories of INRIM, OMH and PTB. The results of the participating laboratories have been analyzed in this report and a good agreement was found between the results provided by most of the participants. These results allowed also determination of the degrees of equivalence of each NMI participating with the EUROMET_key comparison reference values (EU_KCRV); they will provide a basis for the review of the Calibration Measurement Capabilities (CMC) entries on hydrometer calibration, and they allowed the degree of equivalence between pairs of NMIs to be established. The Istitituto Nazionale di Ricerca Metrologica (INRIM), Italy, formerly IMGC-CNR, coordinated the project. Main text. To reach the main text of this Paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Bilateral comparison of 10 V standards between the NSAI - NML (Ireland) and the BIPM, February 2016 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Power, O.; Stock, M.

2016-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland - National Metrology Laboratory (NSAI - NML), Dublin, Ireland, was carried out in January and February 2016. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM7 (Z7) and BIPM9 (Z9), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by NSAI - NML, at the level of 10 V, at NSAI - NML, UNML, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 31 of January 2016. UNML - UBIPM = + 0.22 μV uc = 1.35 μV , at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral Comparison of 10 V Standards between the NSAI - NML (Ireland) and the BIPM, March 2015 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Power, O.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland - National Metrology Laboratory (NSAI - NML), Dublin, Ireland, was carried out in February and March 2015. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM6 (Z6) and BIPMC (ZC), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final resultof the comparison is presented as the difference between the values assigned to DC voltage standards by NSAI - NML, at the level of 10 V,at NSAI - NML, UNML, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 24 February 2015. UNML - UBIPM = - 0.82 mV; uc = 1.35 mV , at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Key comparison study on peptide purity—synthetic human C-peptide

NASA Astrophysics Data System (ADS)

Josephs, R. D.; Li, M.; Song, D.; Westwood, S.; Stoppacher, N.; Daireaux, A.; Choteau, T.; Wielgosz, R.; Xiao, P.; Liu, Y.; Gao, X.; Zhang, C.; Zhang, T.; Mi, W.; Quan, C.; Huang, T.; Li, H.; Flatschart, R.; Borges Oliveira, R.; Melanson, J. E.; Ohlendorf, R.; Henrion, A.; Kinumi, T.; Wong, L.; Liu, Q.; Oztug Senal, M.; Vatansever, B.; Ün, I.; Gören, A. C.; Akgöz, M.; Quaglia, M.; Warren, J.

2017-01-01

Under the auspices of the Protein Analysis Working Group (PAWG) of the Comité Consultatif pour la Quantité de Matière (CCQM) a key comparison, CCQM-K115, was coordinated by the Bureau International des Poids et Mesures (BIPM) and the Chinese National Institute of Metrology (NIM). Eight Metrology Institutes or Designated Institutes and the BIPM participated. Participants were required to assign the mass fraction of human C-peptide (hCP) present as the main component in the comparison sample for CCQM-K115. The comparison samples were prepared from synthetic human hCP purchased from a commercial supplier and used as provided without further treatment or purification. hCP was selected to be representative of the performance of a laboratory's measurement capability for the purity assignment of short (up to 5 kDa), non-cross-linked synthetic peptides/proteins. It was anticipated to provide an analytical measurement challenge representative for the value-assignment of compounds of broadly similar structural characteristics. The majority of participants used a peptide impurity corrected amino acid analysis (PICAA) approach as the amount of material that has been provided to each participant (25 mg) is insufficient to perform a full mass balance based characterization of the material by a participating laboratory. The coordinators, both the BIPM and the NIM, were the laboratories to use the mass balance approach as they had more material available. It was decided to propose KCRVs for both the hCP mass fraction and the mass fraction of the peptide related impurities as indispensable contributor regardless of the use of PICAA, mass balance or any other approach to determine the hCP purity. This allowed participants to demonstrate the efficacy of their implementation of the approaches used to determine the hCP mass fraction. In particular it allows participants to demonstrate the efficacy of their implementation of peptide related impurity identification and quantification

America's Children: Key National Indicators of Well-Being. 2009

ERIC Educational Resources Information Center

Blachman, Dara; Laughlin, Lynda; Lukacs, Susan; Pastor, Patricia; Howie, LaJeana; Sonnenberg, William; Axelrad, Daniel; Steffen, Barry; Baum, Katrina; Lopez, Marsha; Jekielek, Susan; Nord, Mark; Morisi, Teri; Avenevoli, Shelli; Singleton, James; Colpe, Lisa; Fungwe, Thomas; Ghandour, Reem

2009-01-01

"America's Children: Key National Indicators of Well-Being" provides annual updates on the well-being of children and families in the United States across a range of domains. A more detailed report alternates every other year with a condensed version that highlights selected indicators. This year, the Forum is publishing the full report…

Integrated Technology Assessment Center (ITAC) Update

NASA Technical Reports Server (NTRS)

Taylor, J. L.; Neely, M. A.; Curran, F. M.; Christensen, E. R.; Escher, D.; Lovell, N.; Morris, Charles (Technical Monitor)

2002-01-01

The Integrated Technology Assessment Center (ITAC) has developed a flexible systems analysis framework to identify long-term technology needs, quantify payoffs for technology investments, and assess the progress of ASTP-sponsored technology programs in the hypersonics area. For this, ITAC has assembled an experienced team representing a broad sector of the aerospace community and developed a systematic assessment process complete with supporting tools. Concepts for transportation systems are selected based on relevance to the ASTP and integrated concept models (ICM) of these concepts are developed. Key technologies of interest are identified and projections are made of their characteristics with respect to their impacts on key aspects of the specific concepts of interest. Both the models and technology projections are then fed into the ITAC's probabilistic systems analysis framework in ModelCenter. This framework permits rapid sensitivity analysis, single point design assessment, and a full probabilistic assessment of each concept with respect to both embedded and enhancing technologies. Probabilistic outputs are weighed against metrics of interest to ASTP using a multivariate decision making process to provide inputs for technology prioritization within the ASTP. ITAC program is currently finishing the assessment of a two-stage-to-orbit (TSTO), rocket-based combined cycle (RBCC) concept and a TSTO turbine-based combined cycle (TBCC) concept developed by the team with inputs from NASA. A baseline all rocket TSTO concept is also being developed for comparison. Boeing has recently submitted a performance model for their Flexible Aerospace System Solution for Tomorrow (FASST) concept and the ISAT program will provide inputs for a single-stage-to-orbit (SSTO) TBCC based concept in the near-term. Both of these latter concepts will be analyzed within the ITAC framework over the summer. This paper provides a status update of the ITAC program.

Delta's Key to the TOEFL iBT[R]: Advanced Skill Practice. Revised Edition

ERIC Educational Resources Information Center

Gallagher, Nancy

2012-01-01

Delta's Key to the TOEFL iBT: Advanced Skill Practice is a revised and updated edition of Delta's Key to the Next Generation TOEFL Test. Since the introduction of the TOEFL iBT in 2005, there have been significant changes to some of the test questions, particularly the integrated writing and integrated speaking tasks. The new 2011 edition of…

Morphological and molecular data for larval stages of four species of Petasiger Dietz, 1909 (Digenea: Echinostomatidae) with an updated key to the known cercariae from the Palaearctic.

PubMed

Selbach, Christian; Soldánová, Miroslava; Georgieva, Simona; Kostadinova, Aneta; Kalbe, Martin; Sures, Bernd

2014-10-01

Large-tailed echinostomatid cercariae of the genus Petasiger Dietz, 1909 (Digenea: Echinostomatidae) from the planorbid snails Gyraulus albus (Müller) and Planorbis planorbis (L.) collected in Germany and the Czech Republic and metacercariae from Gasterosteus aculeatus L. (Gasterosteiformes: Gasterosteidae) collected in Canada are characterised morphologically and molecularly. The rediae, cercariae and metacercariae are described in detail and compared with the existing data on the larval stages of Petasiger spp. Comparative molecular analyses using 28S rDNA and nad1 mitochondrial sequences supported the distinct status of four species of Petasiger. Molecular and morphological evidence for their distinction and an updated key to the known large-tailed cercariae of Petasiger from the Palaearctic are provided.

Political Education: National Policy Comes of Age. The Updated Edition

ERIC Educational Resources Information Center

Cross, Christopher T.

2010-01-01

Political insider Christopher Cross has updated his critically acclaimed book to reflect recent education policy developments, including the impact of the Obama administration and "Race to the Top" as well as the controversy over NCLB's reauthorization. Featuring a new introduction and the addition of postscripts for key chapters, this…

True fir spacing and yield trials—20-year update

Treesearch

Robert O. Curtis

2013-01-01

This report updates data and comparisons from previous reports (Curtis and others 2000, Curtis 2008) on a series of precommercial thinning and yield trials in high-elevation true fir–hemlock stands, using data from the 12 replicates for which 20-year data are now available. The stands were varying mixtures of Pacific silver fir (Abies amabilis (Douglas ex Loudon)...

Highly efficient model updating for structural condition assessment of large-scale bridges.

DOT National Transportation Integrated Search

2015-02-01

For eciently updating models of large-scale structures, the response surface (RS) method based on radial basis : functions (RBFs) is proposed to model the input-output relationship of structures. The key issues for applying : the proposed method a...

Bilateral key comparison SIM.T-K6.1 on humidity standards in the dew/frost-point temperature range from -25 °C to +20 °C

NASA Astrophysics Data System (ADS)

Meyer, C. W.; Hill, K. D.

2015-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the National Research Council (NRC, Canada) between December 2014 and April 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and NRC and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and NRC. This paper is the final report of the comparison including analysis of the uncertainty of measurement results. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT WG-KC, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Report to the CCT on COOMET comparison COOMET.T-K3.1 (previously COOMET.T-S1): Key regional comparison of the national standards of temperature in the range from the triple point of water to the freezing point of zinc

NASA Astrophysics Data System (ADS)

Pokhodun, A. I.

2010-01-01

In the framework of the CIPM MRA, a first COOMET comparison "Comparison of the ITS-90 realizations in the range from 0.01 °C to 429.7485 °C (from the triple point of water to the freezing point of zinc)", registered in the KCDB under the identifier "COOMET.T-K3", was carried out in 2005-2007. Four national metrology institutes took part in this comparison: VNIIM (Russian Federation), SMU (Slovakia), BelGIM (Republic of Belarus) and NSC IM (Ukraine), and two of them (VNIIM and SMU) ensured the linkage with key comparisons CCT-K3 and CCT-K4, in order to disseminate the metrological equivalence to the measurement standards of NSC IM and BelGIM. NSC IM, however, had to withdraw its results, and at the meeting of Technical Committee T-10 of COOMET it was decided to carry out a supplementary bilateral comparison between VNIIM and the NSC IM for realization of the ITS-90 in the same range of temperature. This was registered in the KCDB under the identifier COOMET.T-S1 and measurements were performed in 2008-2009. From the results presented in this report, it is possible to draw the conclusion that the COOMET supplementary comparison COOMET.T-S1 demonstrates the CMC uncertainties claimed by the NSC IM for the melting point of gallium 0.236 mK (k = 2), and the freezing points of indium 1.040 mK (k = 2), tin 0.858 mK (k = 2) and zinc 0.944 mK (k = 2). In September 2012 the Working Group on key Comparisons (WG 7) of the CCT upgraded this comparison to a COOMET key comparison of the 'CCT-K3' type. It is now identified as COOMET.T-K3.1. In April 2013 this report was superseded by item 03006 in the Technical Supplement of 2013. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

ILRS Website Update

NASA Technical Reports Server (NTRS)

Noll, Carey E.; Torrence, Mark H.; Pollack, Nathan H.; Tyahla, Lori J.

2013-01-01

The ILRS website, http://ilrs.gsfc.nasa.gov, is the central source of information for all aspects of the service. The website provides information on the organization and operation of the ILRS and descriptions of ILRS components data, and products. Furthermore, the website provides an entry point to the archive of these data products available through the data centers. Links are provided to extensive information on the ILRS network stations including performance assesments and data quality evaluations. Descriptions of suported satellite missions (current, future, and past) are provided to aid in station acquisition and data analysis. The website was reently redesigned. Content was reviewed during the update process, ensuring information is current and useful. This poster will provide specific examples of key sections, applicaitons, and webpages.

Final report of the key comparison CCQM-K106: Pb, As and Hg measurements in cosmetic (cream)

NASA Astrophysics Data System (ADS)

Wang, Jun; Wang, Qian; Yamani, Randa Nasr Ahmed; Shehata, Adel B.; Jacimovic, Radojko; Pavlin, Majda; Horvat, Milena; Tsoi, Y. P.; Tsang, C. K.; Shin, Richard; Chailap, Benjamat; Yafa, Charun; Caciano de Sena, Rodrigo; de Almeida, Marcelo; Yim, Yong-Hyeon; Lee, Kyoung-Seok; Heun Kim, Sook; Konopelko, Leonid; Ari, Betül; Tokman, Nilgün; Rienitz, Olaf; Jaehrling, Reinhard; Pape, Carola

2015-01-01

Cosmetics are used in practically all walks of life as a means of improving skin and beautifying complexion. In recent years, more and more attention has been paid to the cosmetic safety. In response to the cosmetic safety issue, the accurate measurement of the heavy metals in cosmetics is, therefore, particularly important. NMIs from different countries should establish their chemical metrology traceability system in this area, which includes both measurement methods research and certain CRMs development. It should be noted that because the matrix of many cosmetics is complex and the contents of the heavy metals are relatively low, it still is a challenging task to measure the analytes with high accuracy and precision. CCQM-K106 followed up CCQM pilot study 'CCQM-P128: Pb, As measurements in cosmetic (cream)' coordinated by the National Institute of Metrology, China (NIM) in 2009. The cream was selected as the testing material, which is widely used as a daily skin care worldwide. This is the first CCQM key comparison regarding the measurement of toxic metal elements with the cosmetic matrix, which includes pure water, liquid paraffin, silicone oil, synthetic squalane, hyaluronic acid, glycerin, propylene glycol, allantoin, preservative and so on. The aim of the CCQM-K106 is to demonstrate the capability of participating NMIs and designated institutes in measuring the contents of poisonous elements, including lead, arsenic and mercury in a cosmetic sample (cream), and support CMC claims relating to inorganic elements in cosmetic materials and similar chemical industry products. The cream matrix sample was prepared under the guidance of professional technicians. The formula of the cream was carefully chosen to match with a real cosmetic. The homogeneity and stability level of Pb, As and Hg in the cream sample were fit for the objective of the comparison. Each participant received two numbered bottles containing about 5g samples in each bottle. The instruction

Key comparison BIPM.RI(I)-K1 of the air-kerma standards of the IST-LPSR, Portugal and the BIPM in 60Co gamma radiation

NASA Astrophysics Data System (ADS)

Kessler, C.; Burns, D.; Cardoso, J.

2018-01-01

A comparison of the standards for air kerma of the Instituto Superior Técnico, Laboratório de Proteção e Segurança Radiológica (IST-LPSR), Portugal and of the Bureau International des Poids et Mesures (BIPM) was carried out in the 60Co radiation beam of the BIPM in December 2015. The comparison result, evaluated as a ratio of the IST-LPSR and the BIPM standards for air kerma, is 1.0026 with a combined standard uncertainty of 1.7 × 10-3. The results for an indirect comparison made at the same time are consistent with the direct results at the level of 1.1 parts in 103. The results are analysed and presented in terms of degrees of equivalence, suitable for entry in the BIPM key comparison database. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Non-unique key B-Tree implementation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ries, D.R.

1980-12-23

The B-Trees are an indexed method to allow fast retrieval and order preserving updates to a FRAMIS relation based on a designated set of keys in the relation. A B-Tree access method is being implemented to provide indexed and sequential (in index order) access to FRAMIS relations. The implementation modifies the basic B-Tree structure to correctly allow multiple key values and still maintain the balanced page fill property of B-Trees. The data structures of the B-Tree are presented first, including the FRAMIS solution to the duplicate key value problem. Then the access level routines and utilities are presented. These routinesmore » include the original B-Tree creation; searching the B-Tree; and inserting, deleting, and replacing tuples on the B-Tree. In conclusion, the uses of the B-Tree access structures at the semantic level to enhance the FRAMIS performance are discussed. 10 figures.« less

Model Update of a Micro Air Vehicle (MAV) Flexible Wing Frame with Uncertainty Quantification

NASA Technical Reports Server (NTRS)

Reaves, Mercedes C.; Horta, Lucas G.; Waszak, Martin R.; Morgan, Benjamin G.

2004-01-01

This paper describes a procedure to update parameters in the finite element model of a Micro Air Vehicle (MAV) to improve displacement predictions under aerodynamics loads. Because of fabrication, materials, and geometric uncertainties, a statistical approach combined with Multidisciplinary Design Optimization (MDO) is used to modify key model parameters. Static test data collected using photogrammetry are used to correlate with model predictions. Results show significant improvements in model predictions after parameters are updated; however, computed probabilities values indicate low confidence in updated values and/or model structure errors. Lessons learned in the areas of wing design, test procedures, modeling approaches with geometric nonlinearities, and uncertainties quantification are all documented.

Interpreting biomonitoring data for 2,4-dichlorophenoxyacetic acid: Update to Biomonitoring Equivalents and population biomonitoring data.

PubMed

Aylward, L L; Hays, S M

2015-12-01

Urinary biomonitoring data for 2,4-dichlorophenoxyacetic acid (2,4-D) reflect aggregate population exposures to trace 2,4-D residues in diet and the environment. These data can be interpreted in the context of current risk assessments by comparison to a Biomonitoring Equivalent (BE), which is an estimate of the average biomarker concentration consistent with an exposure guidance value such as the US EPA Reference Dose (RfD). BE values are updated here from previous published BE values to reflect a change in the US EPA RfD. The US EPA RfD has been updated to reflect a revised point of departure (POD) based on new information from additional toxicological studies and updated assessment of applicable uncertainty factors. In addition, new biomonitoring data from both the US National Health and Nutrition Examination Survey (NHANES) and the Canadian Health Measures Survey (CHMS) have been published. The updated US EPA chronic RfD of 0.21 mg/kg-d results in updated BE values of 10,500 and 7000 μg/L for adults and children, respectively. Comparison of the current population-representative data to these BE values shows that upper bound population biomarker concentrations are more than 5000-fold below BE values corresponding to the updated US EPA RfD. This biomonitoring-based risk assessment supports the conclusion that current use patterns in the US and Canada result in incidental exposures in the general population that can be considered negligible in the context of the current 2,4-D risk assessment. Copyright © 2015 Elsevier Inc. All rights reserved.

Bilateral key comparison SIM.T-K6.5 on humidity standards in the dew/frost-point temperature range from -30 °C to +20 °C

NASA Astrophysics Data System (ADS)

Meyer, C.; Solano, A.

2016-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Laboratorio Costarricense de Metrología (LACOMET, Costa Rica) between February 2015 and August 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and LACOMET and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and LACOMET. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral key comparison SIM.T-K6.2 on humidity standards in the dew/frost-point temperature range from -20 °c to 20 °c

NASA Astrophysics Data System (ADS)

Huang, P. H.; Meyer, C. W.; Martines-López, E.; Dávila Pacheco, J. A.; Méndez-Lango, E.

2014-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Centro Nacional de Metrologia (CENAM, Mexico) between July 2008 and December 2008. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and CENAM and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and CENAM. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, January to February 2013 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Power, O.; Chayramy, R.; Solve, S.; Stock, M.

2014-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from January to February 2013. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_8 (Z8) and BIPM_9 (Z9), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (electromotive force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 5 February 2013. UNML - UBIPM = -0.63 µV uc = 1.31 µV, at 10 V where uc is thecombined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML,based on KJ-90, and the uncertainty related to the comparison. The comparison results show that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated standard uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according

Updating Rhode Island’s Strategic Highway Safety Plan (SHSP) : an RSPCB Peer Exchange

DOT National Transportation Integrated Search

2012-03-01

In January 2012, Rhode Island kicked off its Strategic Highway Safety Plan (SHSP) update with a leadership committee meeting where key safety stakeholders presented an overview of Rhode Islands accomplishments since initial SHSP approval in 2007. ...

KEY COMPARISON: CCQM-K32 key comparison and P84 pilot study: Amount of silicon oxide as a thickness of SiO2 on Si

NASA Astrophysics Data System (ADS)

Seah, M. P.

2008-01-01

CCQM-K32 and P84 were conducted following the pilot study P-38 to demonstrate and document the capability of interested National Metrology Institutes to measure the amount of silicon oxide on silicon wafers expressed as a thickness of SiO2 for nominal thicknesses in the range 1.5 nm to 8 nm. 'Amount of substance' may be expressed in many ways and here the measurand is the thickness of the silicon oxide layer on each of a total of 9 samples of nominal thicknesses in the range 1.5 to 8 nm on (100) and (111) Si substrates, expressed as the thickness of SiO2. This report presents the results from K32 and P84. It includes the data received for the measured values and their associated uncertainties, at 95% confidence, for the 9 samples prior to the deadline for receipt of data. The materials are grown by thermal oxidation in very clean furnaces designed for high quality gate oxides on Si wafers in European and US facilities at the same time as those for the pilot study, P-38. Separate samples were provided to each institute in special containers limiting the carbonaceous contamination to below about 0.3 nm. The 9 samples included 5 samples of ultra-thin SiO2 on (100) orientated wafers of Si and 4 samples of ultra-thin SiO2 on (111) orientated wafers of Si. The measurements from the 11 participating laboratories were conducted using ellipsometry, neutron reflectivity (NR), x-ray photoelectron spectroscopy (XPS) or x-ray reflectivity measurements (XRR), guided by the protocol developed in the pilot study P-38 and reproduced in the Appendix. The measurements are given in tables 2 and 3. A very small correction is then made for the different samples that each laboratory received as in table 4. Where appropriate, method offset values deduced from the pilot study P-38 are given in table 5 leading to comparative data in tables 6 and 7. Values for the key comparison reference values (KCRVs) and their associated uncertainties are made from the weighted means and the expanded

Update to the NASA Lewis Ice Accretion Code LEWICE

NASA Technical Reports Server (NTRS)

Wright, William B.

1994-01-01

This report is intended as an update to NASA CR-185129 'User's Manual for the NASA Lewis Ice Accretion Prediction Code (LEWICE).' It describes modifications and improvements made to this code as well as changes to the input and output files, interactive input, and graphics output. The comparison of this code to experimental data is shown to have improved as a result of these modifications.

Primary Immunodeficiency Diseases: An Update on the Classification from the International Union of Immunological Societies Expert Committee for Primary Immunodeficiency

PubMed Central

Al-Herz, Waleed; Bousfiha, Aziz; Casanova, Jean-Laurent; Chapel, Helen; Conley, Mary Ellen; Cunningham-Rundles, Charlotte; Etzioni, Amos; Fischer, Alain; Franco, Jose Luis; Geha, Raif S.; Hammarström, Lennart; Nonoyama, Shigeaki; Notarangelo, Luigi Daniele; Ochs, Hans Dieter; Puck, Jennifer M.; Roifman, Chaim M.; Seger, Reinhard; Tang, Mimi L. K.

2011-01-01

We report the updated classification of primary immunodeficiency diseases, compiled by the ad hoc Expert Committee of the International Union of Immunological Societies. As compared to the previous edition, more than 15 novel disease entities have been added in the updated version. For each disorders, the key clinical and laboratory features are provided. This updated classification is meant to help in the diagnostic approach to patients with these diseases. PMID:22566844

Supplement to photographic catalog of selected planetary size comparisons

NASA Technical Reports Server (NTRS)

Meszaros, Stephen Paul

1991-01-01

This document updates and extends the photographic catalog of selected planetary size comparisons. It utilizes photographs taken by NASA spacecraft to illustrate size comparisons of planets and moons of the solar system. Global views are depicted at the same scale, within each comparison, allowing size relationships to be studied visually.

The ClinicalTrials.gov results database--update and key issues.

PubMed

Zarin, Deborah A; Tse, Tony; Williams, Rebecca J; Califf, Robert M; Ide, Nicholas C

2011-03-03

The ClinicalTrials.gov trial registry was expanded in 2008 to include a database for reporting summary results. We summarize the structure and contents of the results database, provide an update of relevant policies, and show how the data can be used to gain insight into the state of clinical research. We analyzed ClinicalTrials.gov data that were publicly available between September 2009 and September 2010. As of September 27, 2010, ClinicalTrials.gov received approximately 330 new and 2000 revised registrations each week, along with 30 new and 80 revised results submissions. We characterized the 79,413 registry and 2178 results of trial records available as of September 2010. From a sample cohort of results records, 78 of 150 (52%) had associated publications within 2 years after posting. Of results records available publicly, 20% reported more than two primary outcome measures and 5% reported more than five. Of a sample of 100 registry record outcome measures, 61% lacked specificity in describing the metric used in the planned analysis. In a sample of 700 results records, the mean number of different analysis populations per study group was 2.5 (median, 1; range, 1 to 25). Of these trials, 24% reported results for 90% or less of their participants. ClinicalTrials.gov provides access to study results not otherwise available to the public. Although the database allows examination of various aspects of ongoing and completed clinical trials, its ultimate usefulness depends on the research community to submit accurate, informative data.

Joint Standing Committee on Education: Update on Higher Education Personnel Study

ERIC Educational Resources Information Center

West Virginia Higher Education Policy Commission, 2006

2006-01-01

The following topics are included in this update: (1) Comparison of West Virginia classification and compensation systems to those of the University of Michigan, the University system of Maryland, and the University of North Carolina; (2) Classification and Compensation System Training, including an agenda and summary of a two-day seminar devoted…

Updated: SREB States Transform School Accountability with "NCLB" Waivers. Policy Brief

ERIC Educational Resources Information Center

Decuir, Erica

2014-01-01

This latest brief updates education leaders on the key policies the 13 (Arkansas, Delaware, Florida, Georgia, Kentucky, Louisiana, Maryland, Mississippi, North Carolina, Oklahoma, South Carolina, Tennessee and Virginia) Southern Regional Education Board (SREB) states plan to implement under federal waivers to No Child Left Behind. It details,…

On the poorly known haplogynae spiders of the genus Ochyrocera Simon (Araneae, Ochyroceratidae) from Mexico: description of two new species with an updated identification key for Mexican species.

PubMed

Valdez-Mondragón, Alejandro

2017-01-26

Two new species of the spider genus Ochyrocera Simon 1891 are described from Mexico. Ochyrocera jarocha new species was collected under rotten trunks and hollow trunks in a tropical rainforest, in San Martin Volcano, Veracruz, Mexico. Ochyrocera pojoj new species was collected in a mixed forest, under rotten trunks, in La Trinitaria, Chiapas, Mexico, which represents the third species described from the state of Chiapas. With the description of the two new species herein, six species of Ochyrocera are recorded from Mexico. An updated taxonomic identification key and a distribution map to the Mexican species are provided.

Update of the Nuclear Criticality Slide Rule for the Emergency Response to a Nuclear Criticality Accident

NASA Astrophysics Data System (ADS)

Duluc, Matthieu; Bardelay, Aurélie; Celik, Cihangir; Heinrichs, Dave; Hopper, Calvin; Jones, Richard; Kim, Soon; Miller, Thomas; Troisne, Marc; Wilson, Chris

2017-09-01

AWE (UK), IRSN (France), LLNL (USA) and ORNL (USA) began a long term collaboration effort in 2015 to update the nuclear criticality Slide Rule for the emergency response to a nuclear criticality accident. This document, published almost 20 years ago, gives order of magnitude estimates of key parameters, such as number of fissions and doses (neutron and gamma), useful for emergency response teams and public authorities. This paper will present, firstly the motivation and the long term objectives for this update, then the overview of the initial configurations for updated calculations and preliminary results obtained with modern 3D codes.

Comparison of the Josephson Voltage Standards of the NIMT and the BIPM (part of the ongoing BIPM key comparison BIPM.EM-K10.b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Pimsut, S.; Rujirat, N.

2016-01-01

A comparison of the Josephson array voltage standards of the Bureau International des Poids et Mesures (BIPM) and the National Institute of Metrology - (Thailand), NIMT, was carried out in November 2015 at the level of 10 V. For this exercise, options A and B of the BIPM.EM-K10.b comparison protocol were applied. Option B required the BIPM to provide a reference voltage for measurement by the NIMT using its Josephson standard with its own measuring device. Option A required the NIMT to provide a reference voltage with its Josephson voltage standard for measurement by the BIPM using an analogue nanovoltmeter and associated measurement loop. In all cases the BIPM array was kept floating from ground. The final results were in good agreement within the combined relative standard uncertainty of 2.6 parts in 1010 for the nominal voltage of 10 V. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Finite element modelling and updating of a lively footbridge: The complete process

NASA Astrophysics Data System (ADS)

Živanović, Stana; Pavic, Aleksandar; Reynolds, Paul

2007-03-01

The finite element (FE) model updating technology was originally developed in the aerospace and mechanical engineering disciplines to automatically update numerical models of structures to match their experimentally measured counterparts. The process of updating identifies the drawbacks in the FE modelling and the updated FE model could be used to produce more reliable results in further dynamic analysis. In the last decade, the updating technology has been introduced into civil structural engineering. It can serve as an advanced tool for getting reliable modal properties of large structures. The updating process has four key phases: initial FE modelling, modal testing, manual model tuning and automatic updating (conducted using specialist software). However, the published literature does not connect well these phases, although this is crucial when implementing the updating technology. This paper therefore aims to clarify the importance of this linking and to describe the complete model updating process as applicable in civil structural engineering. The complete process consisting the four phases is outlined and brief theory is presented as appropriate. Then, the procedure is implemented on a lively steel box girder footbridge. It was found that even a very detailed initial FE model underestimated the natural frequencies of all seven experimentally identified modes of vibration, with the maximum error being almost 30%. Manual FE model tuning by trial and error found that flexible supports in the longitudinal direction should be introduced at the girder ends to improve correlation between the measured and FE-calculated modes. This significantly reduced the maximum frequency error to only 4%. It was demonstrated that only then could the FE model be automatically updated in a meaningful way. The automatic updating was successfully conducted by updating 22 uncertain structural parameters. Finally, a physical interpretation of all parameter changes is discussed. This

COOMET.QM-K93 (COOMET 615/RU/13): key comparison in the field of measuring of the ethanol amount fraction in nitrogen (120 μmol/mol)

NASA Astrophysics Data System (ADS)

Konopelko, L. A.; Efremova, O. V.; Fatina, O. V.; Orshanskaia, A. A.; Rozhnov, M. S.; Melnyk, D. M.; Petryshyn, P. V.

2016-01-01

The relevance of the COOMET.QM-K93 comparison is founded on paying particular attention to reliability of measurements which are performed during the medical examination of drivers of vehicles in order to assess the degree of alcoholic intoxication. Standard gas mixtures of ethanol in nitrogen in cylinders under pressure play a key role in providing metrological assurance of breath-alcohol analyzers. Participating laboratories: VNIIM and Ukrmetrteststandart. This comparison was carried out in 2014-2015. This supplementary comparison supports CMC claims for: ethanol in the range 50-500 μmol/mol in a matrix of either nitrogen or synthetic air. Results: The results are consistent with the reference values. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

On-site comparison of Quantum Hall Effect resistance standards of the CMI and the BIPM: ongoing key comparison BIPM.EM-K12

NASA Astrophysics Data System (ADS)

Gournay, Pierre; Rolland, Benjamin; Kučera, Jan; Vojáčková, Lucie

2017-01-01

An on-site comparison of the quantum Hall effect (QHE) resistance standards of the Czech Metrology Institute (CMI) and of the Bureau International des Poids et Mesures (BIPM) was made in April 2017. Measurements of a 100 Ω standard in terms of the conventional value of the von Klitzing constant, RK-90, agreed to 6 parts in 1010 with a relative combined standard uncertainty uc = 25 × 10-10. Measurements of 10000 Ω/100 Ω and 100 Ω/1 Ω ratios agreed to 11 parts in 1010 with uc = 22 × 10-10 and to 33 parts in 1010 with uc = 32 × 10-10, respectively. The influence of the current reversal time has been systematically investigated in order to take into account possible errors due to the Peltier effect, which may be particularly large in 1 Ω standards. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

The Status of School Finance Equity in Texas: A 2009 Update

ERIC Educational Resources Information Center

Cortez, Albert

2009-01-01

In Texas, all students are equal, but once again some are more equal than others. This policy update provides a description of the key elements of the existing Texas school funding system, identifies features that contribute to equity and those that maintain and expand inequity, and includes recommended reforms that would reinstate critical…

Bilateral comparison of 10 V standards between the NSAI-NML (Ireland) and the BIPM, February to March 2012 (part of the ongoing BIPM key comparison BIPM.EM-K11.b)

NASA Astrophysics Data System (ADS)

Power, O.; Solve, S.; Chayramy, R.; Stock, M.

2012-01-01

As part of the on-going BIPM key comparison BIPM.EM-K11.b, a comparison of the 10 V voltage reference standards of the BIPM and the National Standards Authority of Ireland-National Metrology Laboratory (NSAI-NML), Dublin, Ireland, was carried out from February to March 2012. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_C (ZC) and BIPM_D (ZD), were transported by freight to NSAI-NML. At NSAI-NML, the reference standard for DC voltage at the 10 V level consists of a group of characterized Zener diode-based electronic voltage standards. The output EMF (electromotive force) of each travelling standard was measured by direct comparison with the group standard. At the BIPM the travelling standards were calibrated, before and after the measurements at NSAI-NML, with the Josephson voltage standard. Results of all measurements were corrected for the dependence of the output voltages on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the value assigned to DC voltage standard by NSAI-NML, at the level of 10 V, at NSAI-NML, UNML, and that assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 23 February 2012. UNML - UBIPM = +0.83 µV, uc = 1.35 µV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. The final result is impacted by the anomalous offset between the NSAI-NML results for the two transfer standards. The reason for this offset hasn't been determined. However, the difference remains within the total combined standard uncertainty. Therefore, the comparison result shows that the voltage standards maintained by NSAI-NML and the BIPM were equivalent, within their stated expanded uncertainties, on the mean date of the comparison. Main text. To reach the main text of

Numerical modeling and model updating for smart laminated structures with viscoelastic damping

NASA Astrophysics Data System (ADS)

Lu, Jun; Zhan, Zhenfei; Liu, Xu; Wang, Pan

2018-07-01

This paper presents a numerical modeling method combined with model updating techniques for the analysis of smart laminated structures with viscoelastic damping. Starting with finite element formulation, the dynamics model with piezoelectric actuators is derived based on the constitutive law of the multilayer plate structure. The frequency-dependent characteristics of the viscoelastic core are represented utilizing the anelastic displacement fields (ADF) parametric model in the time domain. The analytical model is validated experimentally and used to analyze the influencing factors of kinetic parameters under parametric variations. Emphasis is placed upon model updating for smart laminated structures to improve the accuracy of the numerical model. Key design variables are selected through the smoothing spline ANOVA statistical technique to mitigate the computational cost. This updating strategy not only corrects the natural frequencies but also improves the accuracy of damping prediction. The effectiveness of the approach is examined through an application problem of a smart laminated plate. It is shown that a good consistency can be achieved between updated results and measurements. The proposed method is computationally efficient.

Notification: Key Management Challenges Confronting the U.S. Chemical Safety and Hazard Investigation Board

EPA Pesticide Factsheets

June 9, 2014. The OIG is beginning work to update the fiscal year 2014 list of areas we consider to be the key management challenges confronting the U.S. Chemical Safety and Hazard Investigation Board (CSB).

Continuous variable quantum key distribution: finite-key analysis of composable security against coherent attacks.

PubMed

Furrer, F; Franz, T; Berta, M; Leverrier, A; Scholz, V B; Tomamichel, M; Werner, R F

2012-09-07

We provide a security analysis for continuous variable quantum key distribution protocols based on the transmission of two-mode squeezed vacuum states measured via homodyne detection. We employ a version of the entropic uncertainty relation for smooth entropies to give a lower bound on the number of secret bits which can be extracted from a finite number of runs of the protocol. This bound is valid under general coherent attacks, and gives rise to keys which are composably secure. For comparison, we also give a lower bound valid under the assumption of collective attacks. For both scenarios, we find positive key rates using experimental parameters reachable today.

America's Children in Brief: Key National Indicators of Well-Being, 2012

ERIC Educational Resources Information Center

Federal Interagency Forum on Child and Family Statistics, 2012

2012-01-01

Each year since 1997, the Federal Interagency Forum on Child and Family Statistics has published a report on the well-being of children and families. Pending data availability, the Forum updates all 41 indicators annually on its Web site (http://childstats.gov) and alternates publishing a detailed report, "America's Children: Key National…

America's Children in Brief: Key National Indicators of Well-Being, 2010

ERIC Educational Resources Information Center

Federal Interagency Forum on Child and Family Statistics, 2010

2010-01-01

Each year since 1997, the Federal Interagency Forum on Child and Family Statistics has published a report on the well-being of children and families. The Forum's signature report, "America's Children: Key National Indicators of Well-Being," provides annual updates on the well-being of children and families in the United States across…

Final report: Bilateral key comparison SIM.T-K6.3 on humidity standards in the dew/frost-point temperature range from -30°C to 20°C

NASA Astrophysics Data System (ADS)

Huang, Peter; Meyer, Christopher; Brionizio, Julio D.

2015-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the Instituto Nacional de Metrologia, Qualidade e Tecnologia (INMETRO, Brazil) between October 2009 and March 2010. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and INMETRO and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and INMETRO. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on key comparison APMP.M.P-K13 in hydraulic gauge pressure from 50 MPa to 500 MPa

NASA Astrophysics Data System (ADS)

Kajikawa, Hiroaki; Kobata, Tokihiko; Yadav, Sanjay; Jian, Wu; Changpan, Tawat; Owen, Neville; Yanhua, Li; Hung, Chen-Chuan; Ginanjar, Gigin; Choi, In-Mook

2015-01-01

This report describes the results of a key comparison of hydraulic high-pressure standards at nine National Metrology Institutes (NMIs: NMIJ/AIST, NPLI, NMC/A*STAR, NIMT, NMIA, NIM, CMS/ITRI, KIM-LIPI, and KRISS) within the framework of the Asia-Pacific Metrology Programme (APMP) in order to determine their degrees of equivalence in the pressure range from 50 MPa to 500 MPa in gauge mode. The pilot institute was the National Metrology Institute of Japan (NMIJ/AIST). All participating institutes used hydraulic pressure balances as their pressure standards. A set of pressure balance with a free-deformational piston-cylinder assembly was used as the transfer standard. Three piston-cylinder assemblies, only one at a time, were used to complete the measurements in the period from November 2010 to January 2013. Ten participants completed their measurements and reported the pressure-dependent effective areas of the transfer standard at specified pressures with the associated uncertainties. Since one of the participants withdrew its results, the measurement results of the nine participants were finally compared. The results were linked to the CCM.P-K13 reference values through the results of two linking laboratories, NMIJ/AIST and NPLI. The degrees of equivalence were evaluated by the relative deviations of the participants' results from the CCM.P-K13 key comparison reference values, and their associated combined expanded (k=2) uncertainties. The results of all the nine participating NMIs agree with the CCM.P-K13 reference values within their expanded (k=2) uncertainties in the entire pressure range from 50 MPa to 500 MPa. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Comparison of two optimization algorithms for fuzzy finite element model updating for damage detection in a wind turbine blade

NASA Astrophysics Data System (ADS)

Turnbull, Heather; Omenzetter, Piotr

2018-03-01

vDifficulties associated with current health monitoring and inspection practices combined with harsh, often remote, operational environments of wind turbines highlight the requirement for a non-destructive evaluation system capable of remotely monitoring the current structural state of turbine blades. This research adopted a physics based structural health monitoring methodology through calibration of a finite element model using inverse techniques. A 2.36m blade from a 5kW turbine was used as an experimental specimen, with operational modal analysis techniques utilised to realize the modal properties of the system. Modelling the experimental responses as fuzzy numbers using the sub-level technique, uncertainty in the response parameters was propagated back through the model and into the updating parameters. Initially, experimental responses of the blade were obtained, with a numerical model of the blade created and updated. Deterministic updating was carried out through formulation and minimisation of a deterministic objective function using both firefly algorithm and virus optimisation algorithm. Uncertainty in experimental responses were modelled using triangular membership functions, allowing membership functions of updating parameters (Young's modulus and shear modulus) to be obtained. Firefly algorithm and virus optimisation algorithm were again utilised, however, this time in the solution of fuzzy objective functions. This enabled uncertainty associated with updating parameters to be quantified. Varying damage location and severity was simulated experimentally through addition of small masses to the structure intended to cause a structural alteration. A damaged model was created, modelling four variable magnitude nonstructural masses at predefined points and updated to provide a deterministic damage prediction and information in relation to the parameters uncertainty via fuzzy updating.

Comparison of the Josephson Voltage Standards of the DMDM and the BIPM (part of the ongoing BIPM key comparison BIPM.EM-K10.b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Pantelic-Babic, J.; Sofranac, Z.; Cincar Vujovic, T.

2016-01-01

A comparison of the Josephson array voltage standards of the Bureau International des Poids et Mesures (BIPM) and the Directorate of Measures and Precious Metals (DMDM), Belgrade, Serbia, was carried out in June 2015 at the level of 10 V. For this exercise, options A and B of the BIPM.EM-K10.b comparison protocol were applied. Option B required the BIPM to provide a reference voltage for measurement by the DMDM using its Josephson standard with its own measuring device. Option A required the DMDM to provide a reference voltage with its Josephson voltage standard for measurement by the BIPM using an analogue nanovoltmeter and associated measurement loop. Since no sufficiently stable voltage could be achieved in this configuration, a digital detector was used. In all cases the BIPM array was kept floating from ground. The final results were in good agreement within the combined relative standard uncertainty of 1.5 parts in 1010 for the nominal voltage of 10 V. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Key Competencies. Second Edition.

ERIC Educational Resources Information Center

Haworth, David; Browne, Geoff

Key competencies (or generic skills) have been specified in four sources: Further Education Unit (FEU), United Kingdom (1987); Finn Report (1991) and Mayer Committee (1992), Australia; U.S. Labor Secretary's Commission on Achieving Necessary Skills (SCANS) (June 1991); and Butterworth and Lovell (1983), New South Wales. A comparison of the four…

Nonmarket economic values of forest insect pests: An updated literature review

Treesearch

Randall S. Rosenberger; Lauren A. Bell; Patricia A. Champ; Eric. L. Smith

2012-01-01

This report updates the literature review and synthesis of economic valuation studies on the impacts of forest insect pests by Rosenberger and Smith (1997). A conceptual framework is presented to establish context for the studies. This report also discusses the concept of ecosystem services; identifies key elements of each study; examines areas of future research; and...

Final report on the key comparison, CCM.P-K15 in the pressure range from 1.0 × 10-4 Pa to 1.0 Pa

NASA Astrophysics Data System (ADS)

Wuethrich, Christian; Arai, Kenta; Bergoglio, Mercede; Fedchak, James A.; Jousten, Karl; Hong, Seung Soo; Torres Guzman, Jorge

2017-01-01

The comparison CCM.P-K15 is a key comparison in pressure involving six laboratories in three regional metrological organizations (RMO). The measurand of the comparison is the accommodation coefficient of two spinning rotating gauge characterized in nitrogen from 0.1 mPa up to 1.0 Pa. The two transfer standards were circulated from November 2009 until March 2011. The circulation consisted of three loops, one for each RMO, and a new calibration by the pilot be-tween each loop. The stability of one of the transfer standards was poor and was worse than expected based on the previous history of the transfer standard while the other transfer standard demonstrated good stability while circulated in Europe and America and a fair stability while circulated in Asia. All the participants demonstrated equivalence to the definition of pressure in their respective primary standards. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Model Updating of Complex Structures Using the Combination of Component Mode Synthesis and Kriging Predictor

PubMed Central

Li, Yan; Wang, Dejun; Zhang, Shaoyi

2014-01-01

Updating the structural model of complex structures is time-consuming due to the large size of the finite element model (FEM). Using conventional methods for these cases is computationally expensive or even impossible. A two-level method, which combined the Kriging predictor and the component mode synthesis (CMS) technique, was proposed to ensure the successful implementing of FEM updating of large-scale structures. In the first level, the CMS was applied to build a reasonable condensed FEM of complex structures. In the second level, the Kriging predictor that was deemed as a surrogate FEM in structural dynamics was generated based on the condensed FEM. Some key issues of the application of the metamodel (surrogate FEM) to FEM updating were also discussed. Finally, the effectiveness of the proposed method was demonstrated by updating the FEM of a real arch bridge with the measured modal parameters. PMID:24634612

Cloud Feedback in Atmospheric General Circulation Models: An Update

NASA Technical Reports Server (NTRS)

Cess, R. D.; Zhang, M. H.; Ingram, W. J.; Potter, G. L.; Alekseev, V.; Barker, H. W.; Cohen-Solal, E.; Colman, R. A.; Dazlich, D. A.; DelGenio, A. D.;

A 30-day forecast experiment with the GISS model and updated sea surface temperatures

NASA Technical Reports Server (NTRS)

Spar, J.; Atlas, R.; Kuo, E.

1975-01-01

The GISS model was used to compute two parallel global 30-day forecasts for the month January 1974. In one forecast, climatological January sea surface temperatures were used, while in the other observed sea temperatures were inserted and updated daily. A comparison of the two forecasts indicated no clear-cut beneficial effect of daily updating of sea surface temperatures. Despite the rapid decay of daily predictability, the model produced a 30-day mean forecast for January 1974 that was generally superior to persistence and climatology when evaluated over either the globe or the Northern Hemisphere, but not over smaller regions.

Genome Alignment Spanning Major Poaceae Lineages Reveals Heterogeneous Evolutionary Rates and Alters Inferred Dates for Key Evolutionary Events.

PubMed

Wang, Xiyin; Wang, Jingpeng; Jin, Dianchuan; Guo, Hui; Lee, Tae-Ho; Liu, Tao; Paterson, Andrew H

2015-06-01

Multiple comparisons among genomes can clarify their evolution, speciation, and functional innovations. To date, the genome sequences of eight grasses representing the most economically important Poaceae (grass) clades have been published, and their genomic-level comparison is an essential foundation for evolutionary, functional, and translational research. Using a formal and conservative approach, we aligned these genomes. Direct comparison of paralogous gene pairs all duplicated simultaneously reveal striking variation in evolutionary rates among whole genomes, with nucleotide substitution slowest in rice and up to 48% faster in other grasses, adding a new dimension to the value of rice as a grass model. We reconstructed ancestral genome contents for major evolutionary nodes, potentially contributing to understanding the divergence and speciation of grasses. Recent fossil evidence suggests revisions of the estimated dates of key evolutionary events, implying that the pan-grass polyploidization occurred ∼96 million years ago and could not be related to the Cretaceous-Tertiary mass extinction as previously inferred. Adjusted dating to reflect both updated fossil evidence and lineage-specific evolutionary rates suggested that maize subgenome divergence and maize-sorghum divergence were virtually simultaneous, a coincidence that would be explained if polyploidization directly contributed to speciation. This work lays a solid foundation for Poaceae translational genomics. Copyright © 2015 The Author. Published by Elsevier Inc. All rights reserved.

Bilateral comparison of 1 V and 10 V standards between the INM (Romania) and the BIPM, August to October 2013 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Simionescu, M.; Cîrneanu, L.

2014-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Institut National de Metrologie (INM), Bucharest, Romania, was carried out from August to October 2013. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM_7 (Z7) and BIPM_8 (Z8), were transported by freight to INM. At INM, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (electromotive force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at INM, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by INM, at the level of 1.018 V and 10 V, at INM, UINM, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 6 September 2013. UINM - UBIPM = -0.014 µV uc = 0.051 µV, at 1 V UINM - UBIPM = -0.43 µV uc = 0.34 µV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at INM, based on KJ-90, and the uncertainty related to the comparison. These are satisfactory results. The comparison results show that the voltage standards maintained by INM and the BIPM were equivalent, within the comparison uncertainty, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual

Update of inactivated equine influenza vaccine strain in Japan

PubMed Central

GAMOH, Koichiro; NAKAMURA, Shigeyuki

2017-01-01

Japan established a vaccine selection system, in which a committee evaluates veterinary influenza vaccines to determine if the vaccine should be updated. In 2013, it was concluded that the present equine influenza vaccine strains did not have to be updated, but clade 2 (Fc2) viruses of the Florida sublineage should be included. We collected three Fc2 viruses as candidates and conducted comparative tests. Results indicated that A/equine/Carlow/2011 (H3N8) is not suitable, because of its unstable antigenic characteristics. A comparison between A/equine/Richmond/1/2007 (H3N8) (Richmond/07) and A/equine/Yokohama/aq13/2010 (H3N8) (Yokohama/10) in eggs showed that they shared equal growth properties. Immunogenicity test in mice showed that Yokohama/10 induced higher HI antibody titers than Richmond/07. Therefore, we concluded that Yokohama/10 was the most suitable strain. PMID:28163276

a Bottom-Up Geosptial Data Update Mechanism for Spatial Data Infrastructure Updating

NASA Astrophysics Data System (ADS)

Tian, W.; Zhu, X.; Liu, Y.

2012-08-01

Currently, the top-down spatial data update mechanism has made a big progress and it is wildly applied in many SDI (spatial data infrastructure). However, this mechanism still has some issues. For example, the update schedule is limited by the professional department's project, usually which is too long for the end-user; the data form collection to public cost too much time and energy for professional department; the details of geospatial information does not provide sufficient attribute, etc. Thus, how to deal with the problems has become the effective shortcut. Emerging Internet technology, 3S technique and geographic information knowledge which is popular in the public promote the booming development of geoscience in volunteered geospatial information. Volunteered geospatial information is the current "hotspot", which attracts many researchers to study its data quality and credibility, accuracy, sustainability, social benefit, application and so on. In addition to this, a few scholars also pay attention to the value of VGI to support the SDI updating. And on that basis, this paper presents a bottom-up update mechanism form VGI to SDI, which includes the processes of match homonymous elements between VGI and SDI vector data , change data detection, SDI spatial database update and new data product publication to end-users. Then, the proposed updating cycle is deeply discussed about the feasibility of which can detect the changed elements in time and shorten the update period, provide more accurate geometry and attribute data for spatial data infrastructure and support update propagation.

Working Memory Updating Latency Reflects the Cost of Switching between Maintenance and Updating Modes of Operation

ERIC Educational Resources Information Center

Kessler, Yoav; Oberauer, Klaus

2014-01-01

Updating and maintenance of information are 2 conflicting demands on working memory (WM). We examined the time required to update WM (updating latency) as a function of the sequence of updated and not-updated items within a list. Participants held a list of items in WM and updated a variable subset of them in each trial. Four experiments that vary…

Lazy Updating of hubs can enable more realistic models by speeding up stochastic simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ehlert, Kurt; Loewe, Laurence, E-mail: loewe@wisc.edu; Wisconsin Institute for Discovery, University of Wisconsin-Madison, Madison, Wisconsin 53715

2014-11-28

To respect the nature of discrete parts in a system, stochastic simulation algorithms (SSAs) must update for each action (i) all part counts and (ii) each action's probability of occurring next and its timing. This makes it expensive to simulate biological networks with well-connected “hubs” such as ATP that affect many actions. Temperature and volume also affect many actions and may be changed significantly in small steps by the network itself during fever and cell growth, respectively. Such trends matter for evolutionary questions, as cell volume determines doubling times and fever may affect survival, both key traits for biological evolution.more » Yet simulations often ignore such trends and assume constant environments to avoid many costly probability updates. Such computational convenience precludes analyses of important aspects of evolution. Here we present “Lazy Updating,” an add-on for SSAs designed to reduce the cost of simulating hubs. When a hub changes, Lazy Updating postpones all probability updates for reactions depending on this hub, until a threshold is crossed. Speedup is substantial if most computing time is spent on such updates. We implemented Lazy Updating for the Sorting Direct Method and it is easily integrated into other SSAs such as Gillespie's Direct Method or the Next Reaction Method. Testing on several toy models and a cellular metabolism model showed >10× faster simulations for its use-cases—with a small loss of accuracy. Thus we see Lazy Updating as a valuable tool for some special but important simulation problems that are difficult to address efficiently otherwise.« less

Basis for the ICRP’s updated biokinetic model for carbon inhaled as CO 2

DOE PAGES

Leggett, Richard W.

2017-03-02

Here, the International Commission on Radiological Protection (ICRP) is updating its biokinetic and dosimetric models for occupational intake of radionuclides (OIR) in a series of reports called the OIR series. This paper describes the basis for the ICRP's updated biokinetic model for inhalation of radiocarbon as carbon dioxide (CO 2) gas. The updated model is based on biokinetic data for carbon isotopes inhaled as carbon dioxide or injected or ingested as bicarbonatemore » $$({{{\\rm{HCO}}}_{3}}^{-}).$$ The data from these studies are expected to apply equally to internally deposited (or internally produced) carbon dioxide and bicarbonate based on comparison of excretion rates for the two administered forms and the fact that carbon dioxide and bicarbonate are largely carried in a common form (CO 2–H$${{{\\rm{CO}}}_{3}}^{-})$$ in blood. Compared with dose estimates based on current ICRP biokinetic models for inhaled carbon dioxide or ingested carbon, the updated model will result in a somewhat higher dose estimate for 14C inhaled as CO 2 and a much lower dose estimate for 14C ingested as bicarbonate.« less

Basis for the ICRP’s updated biokinetic model for carbon inhaled as CO 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leggett, Richard W.

Here, the International Commission on Radiological Protection (ICRP) is updating its biokinetic and dosimetric models for occupational intake of radionuclides (OIR) in a series of reports called the OIR series. This paper describes the basis for the ICRP's updated biokinetic model for inhalation of radiocarbon as carbon dioxide (CO 2) gas. The updated model is based on biokinetic data for carbon isotopes inhaled as carbon dioxide or injected or ingested as bicarbonatemore » $$({{{\\rm{HCO}}}_{3}}^{-}).$$ The data from these studies are expected to apply equally to internally deposited (or internally produced) carbon dioxide and bicarbonate based on comparison of excretion rates for the two administered forms and the fact that carbon dioxide and bicarbonate are largely carried in a common form (CO 2–H$${{{\\rm{CO}}}_{3}}^{-})$$ in blood. Compared with dose estimates based on current ICRP biokinetic models for inhaled carbon dioxide or ingested carbon, the updated model will result in a somewhat higher dose estimate for 14C inhaled as CO 2 and a much lower dose estimate for 14C ingested as bicarbonate.« less

The ClinicalTrials.gov Results Database — Update and Key Issues

PubMed Central

Zarin, Deborah A.; Tse, Tony; Williams, Rebecca J.; Califf, Robert M.; Ide, Nicholas C.

2011-01-01

BACKGROUND The ClinicalTrials.gov trial registry was expanded in 2008 to include a database for reporting summary results. We summarize the structure and contents of the results database, provide an update of relevant policies, and show how the data can be used to gain insight into the state of clinical research. METHODS We analyzed ClinicalTrials.gov data that were publicly available between September 2009 and September 2010. RESULTS As of September 27, 2010, ClinicalTrials.gov received approximately 330 new and 2000 revised registrations each week, along with 30 new and 80 revised results submissions. We characterized the 79,413 registry and 2178 results of trial records available as of September 2010. From a sample cohort of results records, 78 of 150 (52%) had associated publications within 2 years after posting. Of results records available publicly, 20% reported more than two primary outcome measures and 5% reported more than five. Of a sample of 100 registry record outcome measures, 61% lacked specificity in describing the metric used in the planned analysis. In a sample of 700 results records, the mean number of different analysis populations per study group was 2.5 (median, 1; range, 1 to 25). Of these trials, 24% reported results for 90% or less of their participants. CONCLUSIONS ClinicalTrials.gov provides access to study results not otherwise available to the public. Although the database allows examination of various aspects of ongoing and completed clinical trials, its ultimate usefulness depends on the research community to submit accurate, informative data. PMID:21366476

Inventory and update on argasid ticks and associated pathogens in Algeria.

PubMed

Lafri, I; Benredjem, W; Neffah-Baaziz, F; Lalout, R; Abdelouahed, K; Gassen, B; Bakhouch, S; Chergui, M; Karakellah, M; Adjmi-Hamoudi, H; Bitam, I

2018-05-01

Argasid ticks include vectors of relapsing fevers caused by Borrelia spp. in humans, and they can transmit arboviruses and other bacterial pathogens. Knowledge about soft ticks ( Ixodida: Argasidae ) in Algeria is incomplete, and distribution data need to be updated. Here we report a series of entomologic investigations that we conducted in five different areas in Algeria between 2012 and 2015. Ticks were identified by entomologic keys and molecular tools (16S rRNA gene). Six distinct species belonging to two genera were identified, including Ornithodoros capensis s.s., Ornithodoros rupestris, Ornithodoros occidentalis, Ornithodoros erraticus, Ornithodoros sonrai and Argas persicus. The present study highlights the distribution of soft ticks, the establishment of an update inventory with nine species and associated pathogens detected in argasid ticks in Algeria.

Investing in updating: how do conclusions change when Cochrane systematic reviews are updated?

PubMed Central

French, Simon D; McDonald, Steve; McKenzie, Joanne E; Green, Sally E

2005-01-01

Background Cochrane systematic reviews aim to provide readers with the most up-to-date evidence on the effects of healthcare interventions. The policy of updating Cochrane reviews every two years consumes valuable time and resources and may not be appropriate for all reviews. The objective of this study was to examine the effect of updating Cochrane systematic reviews over a four year period. Methods This descriptive study examined all completed systematic reviews in the Cochrane Database of Systematic Reviews (CDSR) Issue 2, 1998. The latest version of each of these reviews was then identified in CDSR Issue 2, 2002 and changes in the review were described. For reviews that were updated within this time period and had additional studies, we determined whether their conclusion had changed and if there were factors that were predictive of this change. Results A total of 377 complete reviews were published in CDSR Issue 2, 1998. In Issue 2, 2002, 14 of these reviews were withdrawn and one was split, leaving 362 reviews to examine for the purpose of this study. Of these reviews, 254 (70%) were updated. Of these updated reviews, 23 (9%) had a change in conclusion. Both an increase in precision and a change in statistical significance of the primary outcome were predictive of a change in conclusion of the review. Conclusion The concerns around a lack of updating for some reviews may not be justified considering the small proportion of updated reviews that resulted in a changed conclusion. A priority-setting approach to the updating of Cochrane systematic reviews may be more appropriate than a time-based approach. Updating all reviews as frequently as every two years may not be necessary, however some reviews may need to be updated more often than every two years. PMID:16225692

BILATERAL KEY COMPARISON SIM.T-K6.1 ON HUMIDITY STANDARDS IN THE DEW/FROST-POINT TEMPERATURE RANGE FROM -25 °C TO +20 °C.

PubMed

Meyer, C W; Hill, K D

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the National Research Council (NRC, Canada) between December 2014 and April, 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and NRC and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and NRC.

Bilateral Comparison of 1 V and 10 V Standards between the NIS (Egypt) and the BIPM, August to September 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Abdel Mageed, Hala M.; Aladdin, Omar M.; Raouf, M. Helmy A.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the National Institute for Standards (NIS), Giza, Egypt, was carried out from August to September 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMB (ZB) and BIPMC (ZC), were transported as hand luggage on board an airplane to NIS and back to BIPM. At NIS, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at NIS, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by NIS, at the level of 1.018 V and 10 V, at NIS, UNIS, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 7 September 2014. UNIS - UBIPM = 0.09 µV uc = 0.08 µV, at 1 V UNIS - UBIPM = 0.22 µV uc = 0.14 µV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NIS, based on KJ-90, and the uncertainty related to the comparison. This is a satisfactory result. The comparison result shows that the voltage standards maintained by NIS and the BIPM were equivalent, within their stated standard uncertainties, on the mean date of the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM

Detection of Earthquake-Induced Damage in a Framed Structure Using a Finite Element Model Updating Procedure

PubMed Central

Kim, Seung-Nam; Park, Taewon; Lee, Sang-Hyun

2014-01-01

Damage of a 5-story framed structure was identified from two types of measured data, which are frequency response functions (FRF) and natural frequencies, using a finite element (FE) model updating procedure. In this study, a procedure to determine the appropriate weightings for different groups of observations was proposed. In addition, a modified frame element which included rotational springs was used to construct the FE model for updating to represent concentrated damage at the member ends (a formulation for plastic hinges in framed structures subjected to strong earthquakes). The results of the model updating and subsequent damage detection when the rotational springs (RS model) were used were compared with those obtained using the conventional frame elements (FS model). Comparisons indicated that the RS model gave more accurate results than the FS model. That is, the errors in the natural frequencies of the updated models were smaller, and the identified damage showed clearer distinctions between damaged and undamaged members and was more consistent with observed damage. PMID:24574888

CCM.FF-K3.2011: Final report for the CIPM key comparison of air speed, 0.5 m/s to 40 m/s

NASA Astrophysics Data System (ADS)

Müller, Harald; Caré, Isabelle; Lucas, Peter; Pachinger, Dietmar; Kurihara, Noboru; Lishui, Cui; Su, Chun-Min; Shinder, Iosif; Spazzini, Pier Giorgio

2017-01-01

The CCM.FF-K3.2011 comparison was organized for the purpose of determination of the degree of equivalence of the national standards for air speed over the range 0.5 m/s to 40 m/s. An ultrasonic anemometer and a Laser Doppler anemometer were used as transfer standards. Nine laboratories from three RMOs participated between July 2013 and July 2015—EURAMET: PTB, Germany; LNE-CETIAT, France; INRIM, Italy; VSL, The Netherlands; E+E, Austria; SIM: NIST, USA; APMP: NMIJ/AIST, Japan; NIM, China; CMS/ITRI, Chinese Taipei. The measurements were provided at ambient conditions. All results of independent participants were used in the determination of the key comparison reference value (KCRV) and the uncertainty of the KCRV. The reference value was determined at each air speed separately following `procedure A' presented by M G Cox. The degree of equivalence with the KCRV was calculated for each air speed and laboratory. Almost all reported results were consistent with the KCRV. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Efficient Nondomination Level Update Method for Steady-State Evolutionary Multiobjective Optimization.

PubMed

Li, Ke; Deb, Kalyanmoy; Zhang, Qingfu; Zhang, Qiang

2017-09-01

Nondominated sorting (NDS), which divides a population into several nondomination levels (NDLs), is a basic step in many evolutionary multiobjective optimization (EMO) algorithms. It has been widely studied in a generational evolution model, where the environmental selection is performed after generating a whole population of offspring. However, in a steady-state evolution model, where a population is updated right after the generation of a new candidate, the NDS can be extremely time consuming. This is especially severe when the number of objectives and population size become large. In this paper, we propose an efficient NDL update method to reduce the cost for maintaining the NDL structure in steady-state EMO. Instead of performing the NDS from scratch, our method only updates the NDLs of a limited number of solutions by extracting the knowledge from the current NDL structure. Notice that our NDL update method is performed twice at each iteration. One is after the reproduction, the other is after the environmental selection. Extensive experiments fully demonstrate that, comparing to the other five state-of-the-art NDS methods, our proposed method avoids a significant amount of unnecessary comparisons, not only in the synthetic data sets, but also in some real optimization scenarios. Last but not least, we find that our proposed method is also useful for the generational evolution model.

Quickly updatable hologram images with high performance photorefractive polymer composites

NASA Astrophysics Data System (ADS)

Tsutsumi, Naoto; Kinashi, Kenji; Nonomura, Asato; Sakai, Wataru

2012-02-01

We present here quickly updatable hologram images using high performance photorefractive (PR) polymer composite based on poly(N-vinyl carbazole) (PVCz). PVCz is one of the pioneer materials for photoconductive polymer. PVCz/7- DCST/CzEPA/TNF (44/35/20/1 by wt) gives high diffraction efficiency of 68 % at E = 45 V/μm with fast response speed. Response speed of optical diffraction is the key parameter for real-time 3D holographic display. Key parameter for obtaining quickly updatable hologram images is to control the glass transition temperature lower enough to enhance chromophore orientation. Object image of the reflected coin surface recorded with reference beam at 532 nm (green beam) in the PR polymer composite is simultaneously reconstructed using a red probe beam at 642 nm. Instead of using coin object, object image produced by a computer was displayed on a spatial light modulator (SLM) is used as an object for hologram. Reflected object beam from a SLM interfered with reference beam on PR polymer composite to record a hologram and simultaneously reconstructed by a red probe beam. Movie produced in a computer was recorded as a realtime hologram in the PR polymer composite and simultaneously clearly reconstructed with a video rate.

Notification: Key Management Challenges Confronting the U.S. Chemical Safety and Hazard Investigation Board - FY2016

EPA Pesticide Factsheets

January 21, 2016. The EPA OIG is beginning work to update for fiscal year 2016 its list of proposed key management challenges and internal control weaknesses confronting the U.S. Chemical Safety and Hazard Investigation Board (CSB).

Memory Updating and Mental Arithmetic

PubMed Central

Han, Cheng-Ching; Yang, Tsung-Han; Lin, Chia-Yuan; Yen, Nai-Shing

2016-01-01

Is domain-general memory updating ability predictive of calculation skills or are such skills better predicted by the capacity for updating specifically numerical information? Here, we used multidigit mental multiplication (MMM) as a measure for calculating skill as this operation requires the accurate maintenance and updating of information in addition to skills needed for arithmetic more generally. In Experiment 1, we found that only individual differences with regard to a task updating numerical information following addition (MUcalc) could predict the performance of MMM, perhaps owing to common elements between the task and MMM. In Experiment 2, new updating tasks were designed to clarify this: a spatial updating task with no numbers, a numerical task with no calculation, and a word task. The results showed that both MUcalc and the spatial task were able to predict the performance of MMM but only with the more difficult problems, while other updating tasks did not predict performance. It is concluded that relevant processes involved in updating the contents of working memory support mental arithmetic in adults. PMID:26869971

Update on Development of Mesh Generation Algorithms in MeshKit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jain, Rajeev; Vanderzee, Evan; Mahadevan, Vijay

2015-09-30

MeshKit uses a graph-based design for coding all its meshing algorithms, which includes the Reactor Geometry (and mesh) Generation (RGG) algorithms. This report highlights the developmental updates of all the algorithms, results and future work. Parallel versions of algorithms, documentation and performance results are reported. RGG GUI design was updated to incorporate new features requested by the users; boundary layer generation and parallel RGG support were added to the GUI. Key contributions to the release, upgrade and maintenance of other SIGMA1 libraries (CGM and MOAB) were made. Several fundamental meshing algorithms for creating a robust parallel meshing pipeline in MeshKitmore » are under development. Results and current status of automated, open-source and high quality nuclear reactor assembly mesh generation algorithms such as trimesher, quadmesher, interval matching and multi-sweeper are reported.« less

ISO Standards Update

EPA Science Inventory

This presentation provides a brief update on activities of ISO (International Organization for Standardization) TC (Technical Committee) 285, Clean Cooking Solutions. Slides include information on: (1) Working Group project status updates, (2) background on laboratory and field ...

Updated Italian checklist of Soldier Flies (Diptera, Stratiomyidae).

PubMed

Mason, Franco

2013-01-01

An updated checklist for Stratiomyidae of Italy is presented. Previous knowledge and information are put together in a comprehensive way, integrated also with results obtained by sampling with Malaise traps in some of the test areas of the LIFE+ project ManFor C.BD. At the time of writing, with 91 known species, the Italian fauna of Stratiomyidae is the richest in Europe. Neopachygaster meromelas (Dufour, 1841) and Zabrachia minutissima (Zetterstedt, 1838) are new to the Italian fauna. A comprehensive key to the European species of Chorisops Rondani, 1856 is given.

Updated Italian checklist of Soldier Flies (Diptera, Stratiomyidae)

PubMed Central

Mason, Franco

2013-01-01

Abstract An updated checklist for Stratiomyidae of Italy is presented. Previous knowledge and information are put together in a comprehensive way, integrated also with results obtained by sampling with Malaise traps in some of the test areas of the LIFE+ project ManFor C.BD. At the time of writing, with 91 known species, the Italian fauna of Stratiomyidae is the richest in Europe. Neopachygaster meromelas (Dufour, 1841) and Zabrachia minutissima (Zetterstedt, 1838) are new to the Italian fauna. A comprehensive key to the European species of Chorisops Rondani, 1856 is given. PMID:24146573

Final report on COOMET.QM-K76 (COOMET project no 484/RU/09): Key comparison of primary standard gas mixtures: SO2 in nitrogen (100 µmol/mol)

NASA Astrophysics Data System (ADS)

Konopelko, L. A.; Kustikov, Y. A.; Kolobova, A. V.; Shor, N. B.; Efremova, O. V.; Rozhnov, M. S.; Melnyk, D. M.; Kozia, V. G.; Shpilnyi, S. A.; Petryshyn, P. V.; Iakubov, S. E.; Kluchits, A. S.; Ananyin, V. N.; Mironchik, A. M.; Mokhnach, M. V.; Valkova, M.; Stovcik, V.

2014-01-01

Sulfur dioxide is one of the main contaminants present in the atmosphere due to burning of coal, oil and natural gas, smelting of base metals and production of sulfuric acid. Sulfur dioxide has been the subject of three previous CCQM key comparisons: CCQM-K1.d in 1997, CCQM-K26.b in 2005 and CCQM-K76 in 2010. VNIIM proposed a new COOMET project (No 484/RU/09) in this field, which was registered in the KCDB as key comparison COOMET.QM-K76. It was found that all results were consistent with the reference (gravimetric) values, with observed differences not exceeding ±0.60% and not exceeding either the appropriate assigned expanded uncertainties. VNIIM is the linking laboratory to CCQM-K76. SMU has improved the results obtained in CCQM-K76. The mixtures prepared for this exercise were found to be stable during about one year within the uncertainty of the measurements. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

An Ensemble-Based Smoother with Retrospectively Updated Weights for Highly Nonlinear Systems

NASA Technical Reports Server (NTRS)

Chin, T. M.; Turmon, M. J.; Jewell, J. B.; Ghil, M.

2006-01-01

Monte Carlo computational methods have been introduced into data assimilation for nonlinear systems in order to alleviate the computational burden of updating and propagating the full probability distribution. By propagating an ensemble of representative states, algorithms like the ensemble Kalman filter (EnKF) and the resampled particle filter (RPF) rely on the existing modeling infrastructure to approximate the distribution based on the evolution of this ensemble. This work presents an ensemble-based smoother that is applicable to the Monte Carlo filtering schemes like EnKF and RPF. At the minor cost of retrospectively updating a set of weights for ensemble members, this smoother has demonstrated superior capabilities in state tracking for two highly nonlinear problems: the double-well potential and trivariate Lorenz systems. The algorithm does not require retrospective adaptation of the ensemble members themselves, and it is thus suited to a streaming operational mode. The accuracy of the proposed backward-update scheme in estimating non-Gaussian distributions is evaluated by comparison to the more accurate estimates provided by a Markov chain Monte Carlo algorithm.

PF-WFS Shell Inspection Update December 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, Anthony Eugene; Ledoux, Reina Rebecca; Gonzales, Antonio R.

Since the last project update in FY16:Q2, PF-WFS personnel have advanced in understanding of shell inspection on Coordinate Measuring Machines {CMM} and refined the PF-WFS process to the point it was decided to convert shell inspection from the Sheffield #1 gage to Lietz CM Ms. As a part of introspection on the quality of this process many sets of data have been reviewed and analyzed. This analysis included Sheffield to CMM comparisons, CMM inspection repeatability, fixturing differences, quality check development, probing approach changes. This update report will touch on these improvements that have built the confidence in this process tomore » mainstream it inspecting shells. In addition to the CMM programming advancements, the continuation in refinement of input and outputs for the CMM program has created an archiving scheme, input spline files, an output metafile, and inspection report package. This project will continue to mature. Part designs may require program modifications to accommodate "new to this process" part designs. Technology limitations tied to security and performance are requiring possible changes to computer configurations to support an automated process.« less

KEY COMPARISON: Final report on CCQM-K62: Nutrients in infant/adult formula—Vitamins

NASA Astrophysics Data System (ADS)

Sharpless, Katherine E.; Rimmer, Catherine A.; Phinney, Karen W.; Nelson, Bryant C.; Duewer, David L.; Wise, Stephen A.; Kim, Byungjoo; Liu, Jun; Huang, Ting; Zhang, Wei

2010-01-01

Key comparison CCQM-K62 was designed to enable demonstration of the equivalence in capabilities for measurement of vitamins in a food matrix. A milk-based fortified human infant/adult formula was selected as the matrix based upon material availability and relevance. Because vitamins were added to the CCQM-K62 study material in a single form and at levels significantly higher than those that would be naturally occurring in the milk base, the ability of a laboratory to measure the study vitamins is only indicative of a laboratory's ability to measure vitamins in fortified foods. Target analytes were selected for study because of the ready availability of suitable standard materials and the range of their chemical properties: folic acid (vitamin B9) is a single water-soluble molecular entity that typically occurs at low levels and can be unstable, niacin (vitamin B3) is a single stable molecular entity and is typically present at higher concentrations than the other water-soluble vitamins, vitamin A has multiple molecular forms (including retinol and retinyl palmitate), is fat-soluble and typically occurs at relatively high levels. Results for participants measuring only folic acid or niacin are only indicative of their ability to make that measurement; results for participants measuring both folic acid and niacin are indicative of a laboratory's ability to measure folic acid, thiamine, niacin, and riboflavin in fortified foods but not vitamin C or other water-soluble vitamins. The ability to measure vitamin A (reported as retinol equivalents) in this material is also indicative of the participant's ability to measure vitamin E (as alpha-tocopherol and alpha-tocopheryl acetate) but is not indicative of the ability to measure vitamins D and K, which typically occur at much lower concentrations. The relative degrees of equivalence of the reported measurements for all three analytes in CCQM-K62 were within 10%; however, since only two results were submitted for niacin

Bilateral Comparison of 1 V and 10 V Standards between the SMD (Belgium) and the BIPM October to December 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Vlad, D.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Service Métrologie—Metrologische Dienst (SMD), Brussel, Belgium, was carried out from October to November 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM4 (Z4) and BIPM5 (Z5), were transported by freight to SMD and also back to BIPM. At SMD, the reference standard for DC voltage is a Josephson Voltage Standard (JVS). The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at SMD, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned toDC voltage standards by SMD, at the level of 1.018 V and 10 V, at SMD, USMD, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 5 November 2014. USMD - UBIPM = 0.14 mV; uc = 0.07 mV, at 1 V USMD - UBIPM = 0.09 mV; uc = 0.49 mV , at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at SMD, based on KJ-90, and the uncertainty related to the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral Comparison of 1 V and 10 V Standards between the JV (Norway) and the BIPM, January to February 2015 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Sengebush, F.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Justervesenet (JV), Kjeller, Norway, was carried out from January to February 2015. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM4 (Z4) and BIPM5 (Z5), were transported by freight to JV and also back to BIPM. At JV, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at JV, withthe Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned toDC voltage standards by JV, at the level of 1.018 V and 10 V, at JV, UJV, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 28 January 2015. UJV - UBIPM = 0.23 μV uc = 0.03 μV , at 1 V UJV - UBIPM = 0.63 μV uc = 0.28 μV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at JV, based on KJ-90, and the uncertainty related to the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Bilateral Comparison of 1 V and 10 V Standards between the NIMT (Thailand) and the BIPM October to December 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Pimsut, S.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the National Institute of Metrology (Thailand), NIMT, was carried out from October to December 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMA (ZA) and BIPM6 (Z6), were transported by freight to NIMT and back to BIPM. At NIMT, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at NIMT, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned toDC voltage standards by NIMT, at the level of 1.018 V and 10 V, at NIMT, UNIMT, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of 23 November 2014. UNIMT - UBIPM = 0.16 mV; uc = 0.14 mV, at 1 V UNIMT - UBIPM = - 0.03 mV; uc = 0.11 mV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NIMT, based on KJ-90, and the uncertainty related to the comparison. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Final report on EURAMET.QM-K12: EURAMET key comparison on the determination of the mass fraction of creatinine in serum

NASA Astrophysics Data System (ADS)

Bell, David; Hopley, Chris; Ellison, Stephen L. R.; O'Connor, Gavin

2013-01-01

Creatinine is a well-known marker for the evaluation of kidney function. Its routine measurement is undertaken by many clinical laboratories and comparable results over distance and time are required for effective diagnosis. To address this need many National Measurement Institutes (or designated institutes) provide services in this area via the provision of higher order standards or reference measurements. The organic analysis working group of the consultative committee for amount of substance have conducted two previous key comparisons to assess the equivalence of institutes who provide such services. The purpose of this study was to enable institutes who missed the previous studies to demonstrate their capability for characterizing serum materials containing 1 µg/g to 100 µg/g of creatinine. The study material consisted of two lyophilized serum samples which were used in an external quality control proficiency testing scheme. No target values were available for these materials and all participants reported results within the one month timeframe given for analysis. Five institutes participated in the key study and a single institute submitted results for the parallel pilot study. All participants in the key study used isotope dilution with either gas or liquid chromatography coupled with mass spectrometry. The pilot study laboratory used a novel isotope dilution surface-enhanced Raman spectroscopy method. The comparison reference value for each material was set as the mean of all results submitted by those participating in the key study. The choice of the reference value estimator was constrained as it was deemed more appropriate to treat the data in a similar manner to CCQM-K12 if the relative degrees of equivalence were to be compared. This resulted in reference values of (54.27 ± 0.72) µg/g and (38.01 ± 0.42) µg/g for the two separate materials. The relative degrees of equivalence were calculated and these were compared with the relative degrees of

Neural substrates of updating the prediction through prediction error during decision making.

PubMed

Wang, Ying; Ma, Ning; He, Xiaosong; Li, Nan; Wei, Zhengde; Yang, Lizhuang; Zha, Rujing; Han, Long; Li, Xiaoming; Zhang, Daren; Liu, Ying; Zhang, Xiaochu

2017-08-15

Learning of prediction error (PE), including reward PE and risk PE, is crucial for updating the prediction in reinforcement learning (RL). Neurobiological and computational models of RL have reported extensive brain activations related to PE. However, the occurrence of PE does not necessarily predict updating the prediction, e.g., in a probability-known event. Therefore, the brain regions specifically engaged in updating the prediction remain unknown. Here, we conducted two functional magnetic resonance imaging (fMRI) experiments, the probability-unknown Iowa Gambling Task (IGT) and the probability-known risk decision task (RDT). Behavioral analyses confirmed that PEs occurred in both tasks but were only used for updating the prediction in the IGT. By comparing PE-related brain activations between the two tasks, we found that the rostral anterior cingulate cortex/ventral medial prefrontal cortex (rACC/vmPFC) and the posterior cingulate cortex (PCC) activated only during the IGT and were related to both reward and risk PE. Moreover, the responses in the rACC/vmPFC and the PCC were modulated by uncertainty and were associated with reward prediction-related brain regions. Electric brain stimulation over these regions lowered the performance in the IGT but not in the RDT. Our findings of a distributed neural circuit of PE processing suggest that the rACC/vmPFC and the PCC play a key role in updating the prediction through PE processing during decision making. Copyright © 2017 Elsevier Inc. All rights reserved.

KEY COMPARISON: Final report of APMP.T-K6 (original name APMP-IC-1-97): Comparison of humidity measurements using a dew point meter as a transfer standard

NASA Astrophysics Data System (ADS)

Li, Wang; Takahashi, C.; Hussain, F.; Hong, Yi; Nham, H. S.; Chan, K. H.; Lee, L. T.; Chahine, K.

2007-01-01

This APMP key comparison of humidity measurements using a dew point meter as a transfer standard was carried out among eight national metrology institutes from February 1999 to January 2001. The NMC/SPRING, Singapore was the pilot laboratory and a chilled mirror dew point meter offered by NMIJ was used as a transfer standard. The transfer standard was calibrated by each participating institute against local humidity standards in terms of frost and dew point temperature. Each institute selected its frost/dew point temperature calibration points within the range from -70 °C to 20 °C frost/dew point with 5 °C step. The majority of participating institutes measured from -60 °C to 20 °C frost/dew point and a simple mean evaluation was performed in this range. The differences between the institute values and the simple means for all participating institutes are within two standard deviations from the mean values. Bilateral equivalence was analysed in terms of pair difference and single parameter Quantified Demonstrated Equivalence. The results are presented in the report. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Spending: Where Does the Money Go? A Delta Data Update, 2000-2010

ERIC Educational Resources Information Center

Hurlburt, Steven; Kirshstein, Rita J.

2012-01-01

This is one in a series of data briefs developed by the Delta Cost Project at AIR using data from the "IPEDS Analytics: Delta Cost Project Database 1987-2010," which was released on August 14, 2012, by the U.S. Department of Education, National Center for Education Statistics. The intent of these briefs is to update key tables and figures from…

ClinicalKey: a point-of-care search engine.

PubMed

Vardell, Emily

2013-01-01

ClinicalKey is a new point-of-care resource for health care professionals. Through controlled vocabulary, ClinicalKey offers a cross section of resources on diseases and procedures, from journals to e-books and practice guidelines to patient education. A sample search was conducted to demonstrate the features of the database, and a comparison with similar tools is presented.

APMP.T-K3.4: key comparison of realizations of the ITS-90 over the range -38.8344 °C to 419.527 °C

NASA Astrophysics Data System (ADS)

Joung, W.; Gam, K. S.; Achmadi, A.; Trisna, B. A.

2016-01-01

The APMP bilateral key comparison APMP.T-K3.4 was initiated on the request from RCM-LIPI (Indonesia) to link their national standards to the average reference values (ARVs) of the CCT-K3. Korea Research Institute of Standards and Science (KRISS, Republic of Korea) provided the linkage to the CCT-K3 for temperatures ranging from -38.8344 °C to 419.527 °C. In the APMP.T-K3.4, two standard platinum resistance thermometers (SPRTs) were chosen as the transfer instruments and were calibrated at the ITS-90 fixed-points in the comparison range. The fixed-points in this comparison included Zn freezing point (419.527 °C), Sn freezing point (231.928 °C), In freezing point (156.5985 °C), Ga melting point (29.7646 °C), and Hg triple point (-38.8344 °C). The comparison was carried out in a participant-pilot-participant sequence where KRISS served as the pilot. The linkage was based on the fixed-point resistance ratios of RCM-LIPI relative to the ARVs of the CCT-K3 via the difference between the fixed-point resistance ratios of KRISS and the ARVs of the CCT-K3. The temperature differences between the national standards of RCM-LIPI and the ARVs of the CCT-K3 were within the evaluated comparison uncertainties of the ATPM.T-K3.4. This report provides detailed information on the comparison results, linkage mechanism, and the Degree of Equivalence of the RCM-LIPI relative to the institutes having participated in the CCT-K3. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Updated Multistate Review of Professional Teaching Standards. REL Technical Brief. REL 2010-No. 014

ERIC Educational Resources Information Center

White, Melissa Eiler; Makkonen, Reino; Stewart, Kari Becker

2010-01-01

This review of teaching standards in six states updates a 2009 review (White, Makkonen, and Stewart 2009) by incorporating California's recently adopted teaching standards alongside those from Florida, Illinois, North Carolina, Ohio, and Texas. The previous review was developed at the request of key education agencies in California to inform the…

BILATERAL KEY COMPARISON SIM.T-K6.1 ON HUMIDITY STANDARDS IN THE DEW/FROST-POINT TEMPERATURE RANGE FROM −25 °C TO +20 °C

PubMed Central

Meyer, C.W.; Hill, K.D.

2015-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures was carried out by the National Institute of Standards and Technology (NIST, USA) and the National Research Council (NRC, Canada) between December 2014 and April, 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and NRC and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining degree of equivalence between the dew/frost-point standards of NIST and NRC. PMID:26663952

Morphological leaf variability in natural populations of Pistacia atlantica Desf. subsp. atlantica along climatic gradient: new features to update Pistacia atlantica subsp. atlantica key.

PubMed

El Zerey-Belaskri, Asma; Benhassaini, Hachemi

2016-04-01

The effect of bioclimate range on the variation in Pistacia atlantica Desf. subsp. atlantica leaf morphology was studied on 16 sites in Northwest Algeria. The study examined biometrically mature leaves totaling 3520 compound leaves. Fifteen characters (10 quantitative and 5 qualitative) were assessed on each leaf. For each quantitative character, the nested analysis of variance (ANOVA) was used to examine relative magnitude of variation at each level of the nested hierarchy. The correlation between the climatic parameters and the leaf morphology was examined. The statistical analysis applied on the quantitative leaf characters showed highly significant variation at the within-site level and between-site variation. The correlation coefficient (r) showed also an important correlation between climatic parameters and leaf morphology. The results of this study exhibited several values reported for the first time on the species, such as the length and the width of the leaf (reaching up to 24.5 cm/21.9 cm), the number of leaflets (up to 18 leaflets/leaf), and the petiole length of the terminal leaflet (reaching up to 3.4 cm). The original findings of this study are used to update the P. atlantica subsp. atlantica identification key.

Medicare: Comparison of Catastropic Health Insurance Proposals--an Update.

DTIC Science & Technology

1987-10-01

Accounting Office ICF intermediate care facility SNF skilled nursing facility VA Veterans Administration d4 ....... ’. - --- MEDICARE: COMPARISON OF...optional woe services, such as home and community-based services; services in an intermediate care facility (ICF); and prescribed drugs, dentures

Efficient Deployment of Key Nodes for Optimal Coverage of Industrial Mobile Wireless Networks

PubMed Central

Li, Xiaomin; Li, Di; Dong, Zhijie; Hu, Yage; Liu, Chengliang

2018-01-01

In recent years, industrial wireless networks (IWNs) have been transformed by the introduction of mobile nodes, and they now offer increased extensibility, mobility, and flexibility. Nevertheless, mobile nodes pose efficiency and reliability challenges. Efficient node deployment and management of channel interference directly affect network system performance, particularly for key node placement in clustered wireless networks. This study analyzes this system model, considering both industrial properties of wireless networks and their mobility. Then, static and mobile node coverage problems are unified and simplified to target coverage problems. We propose a novel strategy for the deployment of clustered heads in grouped industrial mobile wireless networks (IMWNs) based on the improved maximal clique model and the iterative computation of new candidate cluster head positions. The maximal cliques are obtained via a double-layer Tabu search. Each cluster head updates its new position via an improved virtual force while moving with full coverage to find the minimal inter-cluster interference. Finally, we develop a simulation environment. The simulation results, based on a performance comparison, show the efficacy of the proposed strategies and their superiority over current approaches. PMID:29439439

Source Update Capture in Information Agents

NASA Technical Reports Server (NTRS)

Ashish, Naveen; Kulkarni, Deepak; Wang, Yao

2003-01-01

In this paper we present strategies for successfully capturing updates at Web sources. Web-based information agents provide integrated access to autonomous Web sources that can get updated. For many information agent applications we are interested in knowing when a Web source to which the application provides access, has been updated. We may also be interested in capturing all the updates at a Web source over a period of time i.e., detecting the updates and, for each update retrieving and storing the new version of data. Previous work on update and change detection by polling does not adequately address this problem. We present strategies for intelligently polling a Web source for efficiently capturing changes at the source.

Working Memory Updating Training Improves Mathematics Performance in Middle School Students With Learning Difficulties.

PubMed

Zhang, Hongxia; Chang, Lei; Chen, Xiaoying; Ma, Liang; Zhou, Renlai

2018-01-01

Working memory (WM) deficit is considered the key cause of learning difficulties (LDs). Studies have shown that WM is plastic and thus can be improved through training. This positive effect is transferable to fluid intelligence and academic performance. This study investigated whether WM updating ability and academic performance in children with LDs could be improved through WM updating training and explored the effects of this training on the children's brain activity. We used a running memory task lasting approximately 40 min per day for 28 days to train a group of 23 children with LDs (TLDs group). We also selected two control groups of 22 children with LDs (CLDs group) and 20 children without LDs (normal control [NC] group). The behavioral results of a pretest indicated that WM updating ability and academic performance in the TLDs and CLDs groups were significantly lower than those in the NC group before training. Compared with the CLDs group, the TLDs group exhibited significant performance improvement in a 2-back WM task, as well as in mathematical ability. Event-related potentials (ERPs) results suggested that the amplitudes of N160 (representative of visual recognition) and P300 (representative of updating processing, which is a valid index for updating WM) in the TLDs and CLDs groups were markedly lower than those in the NC group before training. In the TLDs group, these two components increased considerably after training, approaching levels similar to those in the NC group. The results of this study suggest that WM updating training can improve WM updating ability in children with LDs and the training effect can transfer to mathematical performance in such children. Furthermore, the participants' brain activity levels can exhibit positive changes. This article provides experimental evidence that WM updating training could mitigate the symptoms of LDs to a certain degree.

2000 Montana state rail plan update

DOT National Transportation Integrated Search

2000-01-01

This 2000 Montana Rail Plan Update is a comprehensive update of the State Rail Plan. The purpose of this update is to review the State's role in rail planning, retain eligibility for Local Rail Freight Assistance (LRFA) funding, update the descriptio...

Trends in key economic and social indicators for Pacific Northwest states and counties.

Treesearch

Terry L. Raettig

1999-01-01

Local (county) variations in key social and economic indicators are important in Oregon and Washington. Covered employment, wage and salary, unemployment, and population data for 1987 through 1997 showed regional trends in these indicators, which are compared with national trends. Future updates will be published in the “Production, Prices, Employment, and Trade in...

An Update on Design Tools for Optimization of CMC 3D Fiber Architectures

NASA Technical Reports Server (NTRS)

Lang, J.; DiCarlo, J.

2012-01-01

Objective: Describe and up-date progress for NASA's efforts to develop 3D architectural design tools for CMC in general and for SIC/SiC composites in particular. Describe past and current sequential work efforts aimed at: Understanding key fiber and tow physical characteristics in conventional 2D and 3D woven architectures as revealed by microstructures in the literature. Developing an Excel program for down-selecting and predicting key geometric properties and resulting key fiber-controlled properties for various conventional 3D architectures. Developing a software tool for accurately visualizing all the key geometric details of conventional 3D architectures. Validating tools by visualizing and predicting the Internal geometry and key mechanical properties of a NASA SIC/SIC panel with a 3D orthogonal architecture. Applying the predictive and visualization tools toward advanced 3D orthogonal SiC/SIC composites, and combining them into a user-friendly software program.

Updated preparedness and response framework for influenza pandemics.

PubMed

Holloway, Rachel; Rasmussen, Sonja A; Zaza, Stephanie; Cox, Nancy J; Jernigan, Daniel B

2014-09-26

The complexities of planning for and responding to the emergence of novel influenza viruses emphasize the need for systematic frameworks to describe the progression of the event; weigh the risk of emergence and potential public health impact; evaluate transmissibility, antiviral resistance, and severity; and make decisions about interventions. On the basis of experience from recent influenza responses, CDC has updated its framework to describe influenza pandemic progression using six intervals (two prepandemic and four pandemic intervals) and eight domains. This updated framework can be used for influenza pandemic planning and serves as recommendations for risk assessment, decision-making, and action in the United States. The updated framework replaces the U.S. federal government stages from the 2006 implementation plan for the National Strategy for Pandemic Influenza (US Homeland Security Council. National strategy for pandemic influenza: implementation plan. Washington, DC: US Homeland Security Council; 2006. Available at http://www.flu.gov/planning-preparedness/federal/pandemic-influenza-implementation.pdf). The six intervals of the updated framework are as follows: 1) investigation of cases of novel influenza, 2) recognition of increased potential for ongoing transmission, 3) initiation of a pandemic wave, 4) acceleration of a pandemic wave, 5) deceleration of a pandemic wave, and 6) preparation for future pandemic waves. The following eight domains are used to organize response efforts within each interval: incident management, surveillance and epidemiology, laboratory, community mitigation, medical care and countermeasures, vaccine, risk communications, and state/local coordination. Compared with the previous U.S. government stages, this updated framework provides greater detail and clarity regarding the potential timing of key decisions and actions aimed at slowing the spread and mitigating the impact of an emerging pandemic. Use of this updated framework is

Data update in a land information network

NASA Astrophysics Data System (ADS)

Mullin, Robin C.

1988-01-01

The on-going update of data exchanged in a land information network is examined. In the past, major developments have been undertaken to enable the exchange of data between land information systems. A model of a land information network and the data update process have been developed. Based on these, a functional description of the database and software to perform data updating is presented. A prototype of the data update process was implemented using the ARC/INFO geographic information system. This was used to test four approaches to data updating, i.e., bulk, block, incremental, and alert updates. A bulk update is performed by replacing a complete file with an updated file. A block update requires that the data set be partitioned into blocks. When an update occurs, only the blocks which are affected need to be transferred. An incremental update approach records each feature which is added or deleted and transmits only the features needed to update the copy of the file. An alert is a marker indicating that an update has occurred. It can be placed in a file to warn a user that if he is active in an area containing markers, updated data is available. The four approaches have been tested using a cadastral data set.

KEY COMPARISON: CCEM.RF-K18.CL (GT-RF/00-1): Noise in 50 Ω coaxial line at frequencies up to 1 GHz

NASA Astrophysics Data System (ADS)

Eiø, Christopher; Adamson, David; Randa, James; Allal, Djamel; Uzdin, Rinadij

2006-01-01

A measurement comparison of noise temperature has been carried out between four national metrology laboratories in coaxial line at 30 MHz, 60 MHz and 1 GHz. The identification of this intercomparison is CCEM.RF-K18.CL. Two noise sources have been measured. The following four national laboratories participated in this intercomparison: NPL (United Kingdom), NIST (United States of America), BNM-LNE (France) and VNIIFTRI (Russia). The National Physical Laboratory (UK) acted as the pilot laboratory for the comparison. It can be seen that there is generally good agreement between the laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCEM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

An updated cause specific mortality study of petroleum refinery workers.

PubMed Central

Dagg, T G; Satin, K P; Bailey, W J; Wong, O; Harmon, L L; Swencicki, R E

1992-01-01

An update of a cohort study of 14,074 employees at the Richmond and El Segundo refineries of Chevron USA in California was conducted to further examine mortality patterns. The update added six years of follow up (1981-6) and 941 deaths. As in the previous study, mortality from all causes (standard mortality ratio (SMR) = 73) was significantly lower among men compared with the general United States population. Significant deficits were also found for all cancers combined (SMR = 81), several site specific cancers, and most non-malignant causes of death. Mortality from suicide was increased relative to the United States as a whole. Based on a comparison with California rates, however, men had fewer deaths from suicide than expected. Standard mortality ratios were raised for several other causes of death, but only leukaemia and lymphoreticulosarcoma exhibited a pattern suggestive of an occupational relation. The increase appeared to be confined to those hired before 1949, and in the case of lymphoreticulosarcoma, to Richmond workers. PMID:1554618

BILATERAL KEY COMPARISON SIM.T-K6.5 ON HUMIDITY STANDARDS IN THE DEW/FROST-POINT TEMPERATURE RANGE FROM -30 °C TO +20 °C.

PubMed

Meyer, C W; Solano, A

2016-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures over the range -30 °C TO +20 °C was carried out by the National Institute of Standards and Technology (NIST, USA) and the Laboratorio Costarricense de Metrología (LACOMET, Costa Rica), between February 2015 and August 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and LACOMET and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining the degree of equivalence between the dew/frost-point standards of NIST and LACOMET.

Subsequent bilateral comparison to CCT-K3, CIPM key comparison CCT-K3.1: Comparison of standard platinum resistance thermometers at the triple point of water (T = 273.16 K) and at the melting point of gallium (T = 302.9146 K)

NASA Astrophysics Data System (ADS)

Picard, S.; Nonis, M.; Solve, S.; Allisy-Roberts, P. J.; Renaot, E.; Martin, C.

2011-01-01

A comparison of standard platinum resistance thermometers (SPRTs) has been carried out between the BIPM and the Laboratoire commun de métrologie LNE-CNAM using the melting point of gallium and the triple point of water. The temperature difference at Ga between the BIPM and the LNE-CNAM was determined as 108 µK with an associated combined standard uncertainty of 223 µK. This outcome indicates a present temperature difference of the BIPM of -65 µK with respect to an Average Reference Value from an earlier comparison, with an associated uncertainty of uc = 262 µK. It should be noted that the present BIPM scale is not independent, but traceable to cells used in KC7. The comparison results validate the re-establishment of thermometer calibrations at the BIPM for internal use. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Final report of key comparison AFRIMETS.AUV.A-K5: primary pressure calibration of LS1P microphones according to IEC 61094-2, over the frequency range 2 Hz to 10 kHz.

NASA Astrophysics Data System (ADS)

Nel, R.; Avison, J.; Harris, P.; Blabla, M.; Hämäläinen, J.

2017-01-01

The degrees of equivalence of the AFRIMETS.AUV.A-K5 regional key comparison are reported here as the final report. The scope of the comparison covered the complex pressure sensitivities of two LS1P microphones over the frequency range 2 Hz to 10 kHz in accordance with IEC 61094-2: 2009. Four national metrology institutes from two different regional metrology organisations participated in the comparison. Two LS1P microphones were circulated simultaneously to all the participants in a circular configuration. One of the microphones sensitivity shifted and all results associated with this microphone were subsequently excluded from further analysis and linking. The AFRIMETS.AUV.A-K5 comparison results were linked to the CCAUV.A-K5 comparison results via dual participation in the CCAUV.A-K5 and AFRIMETS.AUV.A-K5 comparisons. The degrees of equivalence, linked to the CCAUV.A-K5 comparison, were calculated for all participants of this comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCAUV, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Terminology of European Education and Training Policy: A Selection of 130 Key Terms. Second Edition

ERIC Educational Resources Information Center

Cedefop - European Centre for the Development of Vocational Training, 2014

2014-01-01

This multilingual glossary defines 130 key terms used in European education and training policy. It is an extended and updated version of "Terminology of European education and training policy" (2008) and "Terminology of vocational training policy" (2004). It considers new priorities of European union policy, mainly in skills…

Enhancing LoRaWAN Security through a Lightweight and Authenticated Key Management Approach.

PubMed

Sanchez-Iborra, Ramon; Sánchez-Gómez, Jesús; Pérez, Salvador; Fernández, Pedro J; Santa, José; Hernández-Ramos, José L; Skarmeta, Antonio F

2018-06-05

Luckily, new communication technologies and protocols are nowadays designed considering security issues. A clear example of this can be found in the Internet of Things (IoT) field, a quite recent area where communication technologies such as ZigBee or IPv6 over Low power Wireless Personal Area Networks (6LoWPAN) already include security features to guarantee authentication, confidentiality and integrity. More recent technologies are Low-Power Wide-Area Networks (LP-WAN), which also consider security, but present initial approaches that can be further improved. An example of this can be found in Long Range (LoRa) and its layer-two supporter LoRa Wide Area Network (LoRaWAN), which include a security scheme based on pre-shared cryptographic material lacking flexibility when a key update is necessary. Because of this, in this work, we evaluate the security vulnerabilities of LoRaWAN in the area of key management and propose different alternative schemes. Concretely, the application of an approach based on the recently specified Ephemeral Diffie⁻Hellman Over COSE (EDHOC) is found as a convenient solution, given its flexibility in the update of session keys, its low computational cost and the limited message exchanges needed. A comparative conceptual analysis considering the overhead of different security schemes for LoRaWAN is carried out in order to evaluate their benefits in the challenging area of LP-WAN.

Revenues: Where Does the Money Come from? A Delta Data Update, 2000-2010

ERIC Educational Resources Information Center

Kirshstein, Rita J.; Hurlburt, Steven

2012-01-01

This is one in a series of data briefs developed by the Delta Cost Project at AIR using data from the "IPEDS Analytics: Delta Cost Project Database 1987-2010," which was released on August 14, 2012, by the U.S. Department of Education, National Center for Education Statistics. The intent of these briefs is to update key tables and figures from…

Dissociating Working Memory Updating and Automatic Updating: The Reference-Back Paradigm

ERIC Educational Resources Information Center

Rac-Lubashevsky, Rachel; Kessler, Yoav

2016-01-01

Working memory (WM) updating is a controlled process through which relevant information in the environment is selected to enter the gate to WM and substitute its contents. We suggest that there is also an automatic form of updating, which influences performance in many tasks and is primarily manifested in reaction time sequential effects. The goal…

Hubble Space Telescope Battery Capacity Update

NASA Technical Reports Server (NTRS)

Hollandsworth, Roger; Armantrout, Jon; Rao, Gopalakrishna M.

2007-01-01

Orbital battery performance for the Hubble Space Telescope is discussed and battery life is predicted which supports decision to replace orbital batteries by 2009-2010 timeframe. Ground characterization testing of cells from the replacement battery build is discussed, with comparison of data from battery capacity characterization with cell studies of Cycle Life and 60% Stress Test at the Naval Weapons Surface Center (NWSC)-Crane, and cell Cycle Life testing at the Marshal Space Flight Center (MSFC). The contents of this presentation includes an update to the performance of the on-orbit batteries, as well as a discussion of the HST Service Mission 4 (SM4) batteries manufactured in 1996 and activated in 2000, and a second set of SM4 backup replacement batteries which began manufacture Jan 11, 2007, with delivery scheduled for July 2008.

Pseudo-updated constrained solution algorithm for nonlinear heat conduction

NASA Technical Reports Server (NTRS)

Tovichakchaikul, S.; Padovan, J.

1983-01-01

This paper develops efficiency and stability improvements in the incremental successive substitution (ISS) procedure commonly used to generate the solution to nonlinear heat conduction problems. This is achieved by employing the pseudo-update scheme of Broyden, Fletcher, Goldfarb and Shanno in conjunction with the constrained version of the ISS. The resulting algorithm retains the formulational simplicity associated with ISS schemes while incorporating the enhanced convergence properties of slope driven procedures as well as the stability of constrained approaches. To illustrate the enhanced operating characteristics of the new scheme, the results of several benchmark comparisons are presented.

Update on value-based medicine.

PubMed

Brown, Melissa M; Brown, Gary C

2013-05-01

To update concepts in Value-Based Medicine, especially in view of the Patient Protection and Affordable Care Act. The Patient Protection and Affordable Care Act assures that some variant of Value-Based Medicine cost-utility analysis will play a key role in the healthcare system. It identifies the highest quality care, thereby maximizing the most efficacious use of healthcare resources and empowering patients and physicians.Standardization is critical for the creation and acceptance of a Value-Based Medicine, cost-utility analysis, information system, since 27 million different input variants can go into a cost-utility analysis. Key among such standards is the use of patient preferences (utilities), as patients best understand the quality of life associated with their health states. The inclusion of societal costs, versus direct medical costs alone, demonstrates that medical interventions are more cost effective and, in many instances, provide a net financial return-on-investment to society referent to the direct medical costs expended. Value-Based Medicine provides a standardized methodology, integrating critical, patient, quality-of-life preferences, and societal costs, to allow the highest quality, most cost-effective care. Central to Value-Based Medicine is the concept that all patients deserve the interventions that provide the greatest patient value (improvement in quality of life and/or length of life).

BILATERAL KEY COMPARISON SIM.T-K6.5 ON HUMIDITY STANDARDS IN THE DEW/FROST-POINT TEMPERATURE RANGE FROM −30 °C TO +20 °C

PubMed Central

Meyer, C.W.; Solano, A.

2016-01-01

A Regional Metrology Organization (RMO) Key Comparison of dew/frost point temperatures over the range −30 °C TO +20 °C was carried out by the National Institute of Standards and Technology (NIST, USA) and the Laboratorio Costarricense de Metrología (LACOMET, Costa Rica), between February 2015 and August 2015. The results of this comparison are reported here, along with descriptions of the humidity laboratory standards for NIST and LACOMET and the uncertainty budget for these standards. This report also describes the protocol for the comparison and presents the data acquired. The results are analyzed, determining the degree of equivalence between the dew/frost-point standards of NIST and LACOMET. PMID:28066029

Assessing the need for an update of a probabilistic seismic hazard analysis using a SSHAC Level 1 study and the Seismic Hazard Periodic Reevaluation Methodology

DOE PAGES

Payne, Suzette J.; Coppersmith, Kevin J.; Coppersmith, Ryan; ...

2017-08-23

A key decision for nuclear facilities is evaluating the need for an update of an existing seismic hazard analysis in light of new data and information that has become available since the time that the analysis was completed. We introduce the newly developed risk-informed Seismic Hazard Periodic Review Methodology (referred to as the SHPRM) and present how a Senior Seismic Hazard Analysis Committee (SSHAC) Level 1 probabilistic seismic hazard analysis (PSHA) was performed in an implementation of this new methodology. The SHPRM offers a defensible and documented approach that considers both the changes in seismic hazard and engineering-based risk informationmore » of an existing nuclear facility to assess the need for an update of an existing PSHA. The SHPRM has seven evaluation criteria that are employed at specific analysis, decision, and comparison points which are applied to seismic design categories established for nuclear facilities in United States. The SHPRM is implemented using a SSHAC Level 1 study performed for the Idaho National Laboratory, USA. The implementation focuses on the first six of the seven evaluation criteria of the SHPRM which are all provided from the SSHAC Level 1 PSHA. Finally, to illustrate outcomes of the SHPRM that do not lead to the need for an update and those that do, the example implementations of the SHPRM are performed for nuclear facilities that have target performance goals expressed as the mean annual frequency of unacceptable performance at 1x10 -4, 4x10 -5 and 1x10 -5.« less

Assessing the need for an update of a probabilistic seismic hazard analysis using a SSHAC Level 1 study and the Seismic Hazard Periodic Reevaluation Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Payne, Suzette J.; Coppersmith, Kevin J.; Coppersmith, Ryan

A key decision for nuclear facilities is evaluating the need for an update of an existing seismic hazard analysis in light of new data and information that has become available since the time that the analysis was completed. We introduce the newly developed risk-informed Seismic Hazard Periodic Review Methodology (referred to as the SHPRM) and present how a Senior Seismic Hazard Analysis Committee (SSHAC) Level 1 probabilistic seismic hazard analysis (PSHA) was performed in an implementation of this new methodology. The SHPRM offers a defensible and documented approach that considers both the changes in seismic hazard and engineering-based risk informationmore » of an existing nuclear facility to assess the need for an update of an existing PSHA. The SHPRM has seven evaluation criteria that are employed at specific analysis, decision, and comparison points which are applied to seismic design categories established for nuclear facilities in United States. The SHPRM is implemented using a SSHAC Level 1 study performed for the Idaho National Laboratory, USA. The implementation focuses on the first six of the seven evaluation criteria of the SHPRM which are all provided from the SSHAC Level 1 PSHA. Finally, to illustrate outcomes of the SHPRM that do not lead to the need for an update and those that do, the example implementations of the SHPRM are performed for nuclear facilities that have target performance goals expressed as the mean annual frequency of unacceptable performance at 1x10 -4, 4x10 -5 and 1x10 -5.« less

Update on MTTF figures for linear and rotary coolers of Thales Cryogenics

NASA Astrophysics Data System (ADS)

van de Groep, W.; van der Weijden, H.; van Leeuwen, R.; Benschop, T.; Cauquil, J. M.; Griot, R.

2012-06-01

Thales Cryogenics has an extensive background in delivering linear and rotary coolers for military, civil and space programs. During the last years several technical improvements have increased the lifetime of all Thales coolers resulting in significantly higher Mean Time To Failure (MTTF) figures. In this paper not only updated MTTF values for most of the products in our portfolio will be presented but also the methodology used to come to these reliability figures will be explained. The differences between rotary and linear coolers will be highlighted including the different failure modes influencing the lifetime under operational conditions. These updated reliability figures are based on extensive test results for both rotary and linear coolers as well as Weibull analysis, failure mode identifications, various types of lifetime testing and field results of operational coolers. The impact of the cooler selection for typical applications will be outlined. This updated reliability approach will enable an improved tradeoff for cooler selection in applications where MTTF and a correct reliability assessment is key. Improbing on cooler selection and an increased insight in cooler reliability will result in a higher uptime and operability of equipment, less risk on unexpected failures and lower costs of ownership.

Improved One-Way Hash Chain and Revocation Polynomial-Based Self-Healing Group Key Distribution Schemes in Resource-Constrained Wireless Networks

PubMed Central

Chen, Huifang; Xie, Lei

2014-01-01

Self-healing group key distribution (SGKD) aims to deal with the key distribution problem over an unreliable wireless network. In this paper, we investigate the SGKD issue in resource-constrained wireless networks. We propose two improved SGKD schemes using the one-way hash chain (OHC) and the revocation polynomial (RP), the OHC&RP-SGKD schemes. In the proposed OHC&RP-SGKD schemes, by introducing the unique session identifier and binding the joining time with the capability of recovering previous session keys, the problem of the collusion attack between revoked users and new joined users in existing hash chain-based SGKD schemes is resolved. Moreover, novel methods for utilizing the one-way hash chain and constructing the personal secret, the revocation polynomial and the key updating broadcast packet are presented. Hence, the proposed OHC&RP-SGKD schemes eliminate the limitation of the maximum allowed number of revoked users on the maximum allowed number of sessions, increase the maximum allowed number of revoked/colluding users, and reduce the redundancy in the key updating broadcast packet. Performance analysis and simulation results show that the proposed OHC&RP-SGKD schemes are practical for resource-constrained wireless networks in bad environments, where a strong collusion attack resistance is required and many users could be revoked. PMID:25529204

Sustainable Outreach: Lessons Learned from Space Update and Discovery Dome

NASA Astrophysics Data System (ADS)

Reiff, P. H.; Sumners, C.; Law, C. C.

2009-12-01

A sustainable program lives on past its initial funding cycle, and develops a network of users that ensures continued life, either by fees, advertising revenue, or by making the program more successful in later sponsored grants. Teachers like free things, so having a sponsor for products such as lithographs or CD-Roms is key to wide distribution. In 1994 we developed “Space Update®”, under the NASA “Public Use of the Internet” program. It has new editions annually, with over 40,000 distributed so far (many purchased but most free at teacher and student workshops). In 1996 we created a special edition “Space Weather®”, which includes the space weather module from Space Update plus other resources. Initially developed with funding from the IMAGE mission, it is now sponsored by Cluster and MMS. A new edition is published annually and distributed in the “Sun-Earth Day” packet; total distribution now exceeds 180,000. “Earth Update” was created in 1999 under cooperative agreement “Museums Teaching Planet Earth”. It now has a total distribution of over 20,000. Both Earth Update and Space Update were developed to be museum kiosk software, and more than 15 museums have them on display. Over 4,000 users are active in our e-Teacher network and 577 in our museum educator network. Although these can certainly be considered successful because of their longevity and user base, we have had a far more dramatic sustainable program arise in the last six years… the “Discovery Dome®”. Invented at HMNS and developed under NASA Cooperative Agreement “Immersive Earth”, this dome was the first digital portable planetarium that also showed fulldome movies with an interactive interface (first shown to the public at the Dec 2003 AGU meeting). The Discovery Dome network (tinyurl.com/DiscDome) has spun those initial 6 NASA-funded domes into over 90 installations in 22 states and 23 countries. Creating high quality content is quite expensive and so needs

SWCD: a sliding window and self-regulated learning-based background updating method for change detection in videos

NASA Astrophysics Data System (ADS)

Işık, Şahin; Özkan, Kemal; Günal, Serkan; Gerek, Ömer Nezih

2018-03-01

Change detection with background subtraction process remains to be an unresolved issue and attracts research interest due to challenges encountered on static and dynamic scenes. The key challenge is about how to update dynamically changing backgrounds from frames with an adaptive and self-regulated feedback mechanism. In order to achieve this, we present an effective change detection algorithm for pixelwise changes. A sliding window approach combined with dynamic control of update parameters is introduced for updating background frames, which we called sliding window-based change detection. Comprehensive experiments on related test videos show that the integrated algorithm yields good objective and subjective performance by overcoming illumination variations, camera jitters, and intermittent object motions. It is argued that the obtained method makes a fair alternative in most types of foreground extraction scenarios; unlike case-specific methods, which normally fail for their nonconsidered scenarios.

Hourly Updated GNSS Orbit and Clock

NASA Astrophysics Data System (ADS)

Song, S.; Xue, J.

2016-12-01

With the development of the performance of GNSS, the hourly updated orbit and clock of GNSS are paid much more attention and used by more and more users because of the timeliness and high accuracy. The hourly GNSS orbit and clock are produced routinely in Shanghai Analysis Center(AC) of the International GNSS Monitoring and Assessment Service (iGMAS).In this article, the accuracy of hourly and 6-hourly updated ultra-rapid GPS,GLONASS,GALILEO,BDS orbit and clock (SHU1 and SHU6) are analyzed relative to the final production in detail. The analysis show that, in calculation session, there's no much difference between the mean SHU1 and SHU6 RMS and STD for GNSS orbit and clock. However, for BDS clock in prediction session, the RMS and STD of BDS SHU1 are 2.6ns and 0.5ns respectively, the RMS of BDS SHU6 increase from 2.7ns to 4.5ns from the 1st to the 6th hour prediction session, but there's no much changes of STD. For GPS clock in prediction session, the RMS and STD of GPS SHU1 is quite stable with 0.5ns and 0.2ns.The RMS of GPS SHU6 clock increase from 0.6ns to 1.0ns from the 1st to the 6th hour, but STD is stable at about 0.2ns.For the orbit in calculate session, the RMS of BDS SHU1 is a little less than that of SHU6,the RMS of GPS SHU1 and SHU6 orbit are approximately at the same level. In prediction session, the RMS of IGSO/MEO for BDS SHU1 is relative stable, but the RMS of SHU6 1st-6th hour prediction session increase from about 26.5cm to 32.7cm. The RMS of GPS SHU1 orbit's prediction session is about 3.4cm,but which increase from 3.3cm to 4.3cm for GPS SHU6 1st-6th hour prediction session.The comparison of GLONASS and GALILEO orbit and clock also will be described.The results show that the hourly update is more important for BDS at this stage.Moreover,some problems appearing in satellites and stations can be found earlier by 1 hourly updated frequency.

An official American Thoracic Society/European Respiratory Society statement: key concepts and advances in pulmonary rehabilitation.

PubMed

Spruit, Martijn A; Singh, Sally J; Garvey, Chris; ZuWallack, Richard; Nici, Linda; Rochester, Carolyn; Hill, Kylie; Holland, Anne E; Lareau, Suzanne C; Man, William D-C; Pitta, Fabio; Sewell, Louise; Raskin, Jonathan; Bourbeau, Jean; Crouch, Rebecca; Franssen, Frits M E; Casaburi, Richard; Vercoulen, Jan H; Vogiatzis, Ioannis; Gosselink, Rik; Clini, Enrico M; Effing, Tanja W; Maltais, François; van der Palen, Job; Troosters, Thierry; Janssen, Daisy J A; Collins, Eileen; Garcia-Aymerich, Judith; Brooks, Dina; Fahy, Bonnie F; Puhan, Milo A; Hoogendoorn, Martine; Garrod, Rachel; Schols, Annemie M W J; Carlin, Brian; Benzo, Roberto; Meek, Paula; Morgan, Mike; Rutten-van Mölken, Maureen P M H; Ries, Andrew L; Make, Barry; Goldstein, Roger S; Dowson, Claire A; Brozek, Jan L; Donner, Claudio F; Wouters, Emiel F M

2013-10-15

Pulmonary rehabilitation is recognized as a core component of the management of individuals with chronic respiratory disease. Since the 2006 American Thoracic Society (ATS)/European Respiratory Society (ERS) Statement on Pulmonary Rehabilitation, there has been considerable growth in our knowledge of its efficacy and scope. The purpose of this Statement is to update the 2006 document, including a new definition of pulmonary rehabilitation and highlighting key concepts and major advances in the field. A multidisciplinary committee of experts representing the ATS Pulmonary Rehabilitation Assembly and the ERS Scientific Group 01.02, "Rehabilitation and Chronic Care," determined the overall scope of this update through group consensus. Focused literature reviews in key topic areas were conducted by committee members with relevant clinical and scientific expertise. The final content of this Statement was agreed on by all members. An updated definition of pulmonary rehabilitation is proposed. New data are presented on the science and application of pulmonary rehabilitation, including its effectiveness in acutely ill individuals with chronic obstructive pulmonary disease, and in individuals with other chronic respiratory diseases. The important role of pulmonary rehabilitation in chronic disease management is highlighted. In addition, the role of health behavior change in optimizing and maintaining benefits is discussed. The considerable growth in the science and application of pulmonary rehabilitation since 2006 adds further support for its efficacy in a wide range of individuals with chronic respiratory disease.

International comparison CCQM-K111—propane in nitrogen

NASA Astrophysics Data System (ADS)

van der Veen, Adriaan M. H.; Wouter van der Hout, J.; Ziel, Paul R.; Oudwater, Rutger J.; Fioravante, Andreia L.; Augusto, Cristiane R.; Coutinho Brum, Mariana; Uehara, Shinji; Akima, Dai; Bae, Hyun Kil; Kang, Namgoo; Woo, Jin-Chun; Liaskos, Christina E.; Rhoderick, George C.; Jozela, Mudalo; Tshilongo, James; Ntsasa, Napo G.; Botha, Angelique; Brewer, Paul J.; Brown, Andrew S.; Bartlett, Sam; Downey, Michael L.; Konopelko, L. A.; Kolobova, A. V.; Pankov, A. A.; Orshanskaya, A. A.; Efremova, O. V.

2017-01-01

This key comparison aims to assess the core capabilities of the participants in gas analysis. Such competences include, among others, the capabilities to prepare primary standard gas Mixtures (PSMs), perform the necessary purity analysis on the materials used in the gas mixture preparation, the verification of the composition of newly prepared PSMs against existing ones, and the capability of calibrating the composition of a gas mixture. According to the Strategy for Key Comparisons of the Gas Analysis Working Group, this key comparison is classified as a track A key comparison, which means that the results of this key comparison can be used to underpin calibration and measurement capabilities using the flexible scheme, and for propane under the default scheme. The artefacts were binary mixtures of propane in nitrogen at a nominal amount-of-substance fraction level of 1000 μmol/mol. The values and uncertainties from the gravimetric gas mixture preparation were used as key comparison reference values (KCRVs). Each transfer standard had its own KCRV. The results are generally good. All results but one are within +/- 0.2 % of the KCRV. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

The Texas Medication Algorithm Project antipsychotic algorithm for schizophrenia: 2003 update.

PubMed

Miller, Alexander L; Hall, Catherine S; Buchanan, Robert W; Buckley, Peter F; Chiles, John A; Conley, Robert R; Crismon, M Lynn; Ereshefsky, Larry; Essock, Susan M; Finnerty, Molly; Marder, Stephen R; Miller, Del D; McEvoy, Joseph P; Rush, A John; Saeed, Sy A; Schooler, Nina R; Shon, Steven P; Stroup, Scott; Tarin-Godoy, Bernardo

2004-04-01

The Texas Medication Algorithm Project (TMAP) has been a public-academic collaboration in which guidelines for medication treatment of schizophrenia, bipolar disorder, and major depressive disorder were used in selected public outpatient clinics in Texas. Subsequently, these algorithms were implemented throughout Texas and are being used in other states. Guidelines require updating when significant new evidence emerges; the antipsychotic algorithm for schizophrenia was last updated in 1999. This article reports the recommendations developed in 2002 and 2003 by a group of experts, clinicians, and administrators. A conference in January 2002 began the update process. Before the conference, experts in the pharmacologic treatment of schizophrenia, clinicians, and administrators reviewed literature topics and prepared presentations. Topics included ziprasidone's inclusion in the algorithm, the number of antipsychotics tried before clozapine, and the role of first generation antipsychotics. Data were rated according to Agency for Healthcare Research and Quality criteria. After discussing the presentations, conference attendees arrived at consensus recommendations. Consideration of aripiprazole's inclusion was subsequently handled by electronic communications. The antipsychotic algorithm for schizophrenia was updated to include ziprasidone and aripiprazole among the first-line agents. Relative to the prior algorithm, the number of stages before clozapine was reduced. First generation antipsychotics were included but not as first-line choices. For patients refusing or not responding to clozapine and clozapine augmentation, preference was given to trying monotherapy with another antipsychotic before resorting to antipsychotic combinations. Consensus on algorithm revisions was achieved, but only further well-controlled research will answer many key questions about sequence and type of medication treatments of schizophrenia.

An Updated Nuclear Equation of State for Neutron Stars and Supernova Simulations

NASA Astrophysics Data System (ADS)

Meixner, M. A.; Mathews, G. J.; Dalhed, H. E.; Lan, N. Q.

2011-10-01

We present an updated and improved Equation of State based upon the framework originally developed by Bowers & Wilson. The details of the EoS and improvements are described along with a description of how to access this EOS for numerical simulations. Among the improvements are an updated compressibility based upon recent measurements, the possibility of the formation of proton excess (Ye> 0.5) material and an improved treatment of the nuclear statistical equilibrium and the transition to pasta nuclei as the density approaches nuclear matter density. The possibility of a QCD chiral phase transition is also included at densities above nuclear matter density. We show comparisons of this EOS with the other two publicly available equations of state used in supernova collapse simulations. The advantages of the present EoS is that it is easily amenable to phenomenological parameterization to fit observed explosion properties and to accommodate new physical parameters.

Quality Management and Key Performance Indicators in Oncologic Esophageal Surgery.

PubMed

Gockel, Ines; Ahlbrand, Constantin Johannes; Arras, Michael; Schreiber, Elke Maria; Lang, Hauke

2015-12-01

Ranking systems and comparisons of quality and performance indicators will be of increasing relevance for complex "high-risk" procedures such as esophageal cancer surgery. The identification of evidence-based standards relevant for key performance indicators in esophageal surgery is essential for establishing monitoring systems and furthermore a requirement to enhance treatment quality. In the course of this review, we analyze the key performance indicators case volume, radicality of resection, and postoperative morbidity and mortality, leading to continuous quality improvement. Ranking systems established on this basis will gain increased relevance in highly complex procedures within the national and international comparison and furthermore improve the treatment of patients with esophageal carcinoma.

International comparison CCQM-K111.1—propane in nitrogen

NASA Astrophysics Data System (ADS)

van der Veen, Adriaan M. H.; Wouter van der Hout, J.; Ziel, Paul R.; Jozela, Mudalo; Tshilongo, James; Ntsasa, Napo G.; Botha, Angelique

2017-01-01

This key comparison aims to assess the core capabilities of the participants in gas analysis. Such competences include, among others, the capability of preparing Primary Standard gas Mixtures (PSMs), performing the necessary purity analysis on the materials used in the gas mixture preparation, the verification of the composition of newly prepared PSMs against existing ones, and the capability of calibrating the composition of a gas mixture. According to the Strategy for Key Comparisons of the Gas Analysis Working Group, this subsequent key comparison is classified as a track B key comparison, which means that the results of this key comparison can be used to underpin calibration and measurement capabilities for propane under the default scheme. The artefact was a binary mixture of propane in nitrogen at a nominal amount-of-substance fraction level of 1000 μmol/mol. The values and uncertainties from the gravimetric gas mixture preparation were used as key comparison reference values (KCRVs). Each transfer standard had its own KCRV. The result of the participating laboratory is consistent with the key comparison reference value within the respective expanded uncertainties and deviates less than 0.1 %. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

National Hydropower Plant Dataset, Version 1 (Update FY18Q2)

DOE Data Explorer

Samu, Nicole; Kao, Shih-Chieh; O'Connor, Patrick; Johnson, Megan; Uria-Martinez, Rocio; McManamay, Ryan

2016-09-30

The National Hydropower Plant Dataset, Version 1, Update FY18Q2, includes geospatial point-level locations and key characteristics of existing hydropower plants in the United States that are currently online. These data are a subset extracted from NHAAP’s Existing Hydropower Assets (EHA) dataset, which is a cornerstone of NHAAP’s EHA effort that has supported multiple U.S. hydropower R&D research initiatives related to market acceleration, environmental impact reduction, technology-to-market activities, and climate change impact assessment.

Fluorescent Carbon Nanoparticles in Medicine for Cancer Therapy: An Update.

PubMed

Rani, Reshma; Kumar, Vinit; Rizzolio, Flavio

2018-01-11

In the past few years since our viewpoint on carbon nanoparticles was first published in 2013 (Kumar, V.; Toffoli, G.; Rizzolio, F. ACS Med. Chem. Lett. 2013 , 4 (11), 1012-1013), a considerable progress has been made in the area of synthesis, functionalization, and applications of fluorescent carbon nanoparticles (CNPs). This update aims to highlight some key points achieved in the last 4 years in the development of CNPs with a particular emphasis on the approaches to ameliorate clinical applications of CNPs as therapeutics, diagnostics, and theranostics agents.

Updated U.S. population standard for the Veterans RAND 12-item Health Survey (VR-12).

PubMed

Selim, Alfredo J; Rogers, William; Fleishman, John A; Qian, Shirley X; Fincke, Benjamin G; Rothendler, James A; Kazis, Lewis E

2009-02-01

The purpose of this project was to develop an updated U.S. population standard for the Veterans RAND 12-item Health Survey (VR-12). We used a well-defined and nationally representative sample of the U.S. population from 52,425 responses to the Medical Expenditure Panel Survey (MEPS) collected between 2000 and 2002. We applied modified regression estimates to update the non-proprietary 1990 scoring algorithms. We applied the updated standard to the Medicare Health Outcomes Survey (HOS) to compute the VR-12 physical (PCS((MEPS standard))) and mental (MCS((MEPS standard))) component summaries based on the MEPS. We compared these scores to PCS and MCS based on the 1990 U.S. population standard. Using the updated U.S. population standard, the average VR-12 PCS((MEPS standard)) and MCS((MEPS standard)) scores in the Medicare HOS were 39.82 (standard deviation [SD] = 12.2) and 50.08 (SD = 11.4), respectively. For the same Medicare HOS, the average PCS and MCS scores based on the 1990 standard were 1.40 points higher and 0.99 points lower in comparison to VR-12 PCS and MCS, respectively. Changes in the U.S. population between 1990 and today make the old standard obsolete for the VR-12, so the updated standard developed here is widely available to serve as such a contemporary standard for future applications for health-related quality of life (HRQoL) assessments.

A Comparison of Three Online Information Retrieval Services.

ERIC Educational Resources Information Center

Zais, Harriet W.

Three firms which offer online information retrieval are compared. The firms are Lockheed Information Service, System Development Corporation and the Western Research Application Center. Comparison tables provide information such as hours accessible, coverage, file update, search elements and cost figures for 15 data bases. In addition, general…

Using indirect comparisons to compare interventions within a Cochrane review: a tool for comparative effectiveness research.

PubMed

Agapova, Maria; Devine, Emily B; Nguyen, Hiep; Wolf, Fredric M; Inoue, Lurdes Y T

2014-07-01

Assessing relative performance among competing interventions is an important part of comparative effectiveness research. Bayesian indirect comparisons add information to existing Cochrane reviews, such as which intervention is likely to perform best. However, heterogeneity variance priors may influence results and, potentially, clinical guidance. We highlight the features of Bayesian indirect comparisons using a case study of a Cochrane review update in asthma care. The probability that one self-management educational intervention outperforms others is estimated. Simulation studies investigate the effect of heterogeneity variance prior distributions. Results suggest a 55% probability that individual education is best, followed by combination (39%) and group (6%). The intervention with few trials was sensitive to prior distributions. Bayesian indirect comparisons updates of Cochrane reviews are valuable comparative effectiveness research tools.

Comparisons of the Outcome Prediction Performance of Injury Severity Scoring Tools Using the Abbreviated Injury Scale 90 Update 98 (AIS 98) and 2005 Update 2008 (AIS 2008)

PubMed Central

Tohira, Hideo; Jacobs, Ian; Mountain, David; Gibson, Nick; Yeo, Allen

2011-01-01

The Abbreviated Injury Scale (AIS) was revised in 2005 and updated in 2008 (AIS 2008). We aimed to compare the outcome prediction performance of AIS-based injury severity scoring tools by using AIS 2008 and AIS 98. We used all major trauma patients hospitalized to the Royal Perth Hospital between 1994 and 2008. We selected five AIS-based injury severity scoring tools, including Injury Severity Score (ISS), New Injury Severity Score (NISS), modified Anatomic Profile (mAP), Trauma and Injury Severity Score (TRISS) and A Severity Characterization of Trauma (ASCOT). We selected survival after injury as a target outcome. We used the area under the Receiver Operating Characteristic curve (AUROC) as a performance measure. First, we compared the five tools using all cases whose records included all variables for the TRISS (complete dataset) using a 10-fold cross-validation. Second, we compared the ISS and NISS for AIS 98 and AIS 2008 using all subjects (whole dataset). We identified 1,269 and 4,174 cases for a complete dataset and a whole dataset, respectively. With the 10-fold cross-validation, there were no clear differences in the AUROCs between the AIS 98- and AIS 2008-based scores. With the second comparison, the AIS 98-based ISS performed significantly worse than the AIS 2008-based ISS (p<0.0001), while there was no significant difference between the AIS 98- and AIS 2008-based NISSs. Researchers should be aware of these findings when they select an injury severity scoring tool for their studies. PMID:22105401

Comparisons of the Outcome Prediction Performance of Injury Severity Scoring Tools Using the Abbreviated Injury Scale 90 Update 98 (AIS 98) and 2005 Update 2008 (AIS 2008).

PubMed

Tohira, Hideo; Jacobs, Ian; Mountain, David; Gibson, Nick; Yeo, Allen

2011-01-01

The Abbreviated Injury Scale (AIS) was revised in 2005 and updated in 2008 (AIS 2008). We aimed to compare the outcome prediction performance of AIS-based injury severity scoring tools by using AIS 2008 and AIS 98. We used all major trauma patients hospitalized to the Royal Perth Hospital between 1994 and 2008. We selected five AIS-based injury severity scoring tools, including Injury Severity Score (ISS), New Injury Severity Score (NISS), modified Anatomic Profile (mAP), Trauma and Injury Severity Score (TRISS) and A Severity Characterization of Trauma (ASCOT). We selected survival after injury as a target outcome. We used the area under the Receiver Operating Characteristic curve (AUROC) as a performance measure. First, we compared the five tools using all cases whose records included all variables for the TRISS (complete dataset) using a 10-fold cross-validation. Second, we compared the ISS and NISS for AIS 98 and AIS 2008 using all subjects (whole dataset). We identified 1,269 and 4,174 cases for a complete dataset and a whole dataset, respectively. With the 10-fold cross-validation, there were no clear differences in the AUROCs between the AIS 98- and AIS 2008-based scores. With the second comparison, the AIS 98-based ISS performed significantly worse than the AIS 2008-based ISS (p<0.0001), while there was no significant difference between the AIS 98- and AIS 2008-based NISSs. Researchers should be aware of these findings when they select an injury severity scoring tool for their studies.

Build-Up Approach to Updating the Mock Quiet Spike Beam Model

NASA Technical Reports Server (NTRS)

Herrera, Claudia Y.; Pak, Chan-gi

2007-01-01

an updated model that has similar mode shapes and frequencies as those of the target model. The Mode Matching Code output frequencies and modal assurance criteria (MAC) values that allow for the quantified comparison of the updated model versus the target model. A recent application of this code is the F453 supersonic flight testing platform, NASA DFRC possesses a modified F-15B that is used as a test bed aircraft for supersonic flight experiments. Traditionally, the finite element model of the test article is generated. A GVT is done on the test article ta validate and update its FEM. This FEM is then mated to the F-15B model, which was correlated to GVT data in fall of 2004, A GVT is conducted with the test article mated to the aircraft, and this mated F-15B/ test article FEM is correlated to this final GVT.

Bilateral comparison of 1 V and 10 V standards between the DEFNAT (Tunisia) and the BIPM February to March 2016 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Ben Salah, B.; Mallat, A.; Abene, L.; Stock, M.

2016-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Laboratoire de Métrologie Electrique, DEFNAT (Tunisia), was carried out from February to March 2016. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMC (ZC) and BIPM6 (Z6), were transported by freight to DEFNAT and back to BIPM. In order to keep the Zeners powered during their transportation phase, a BIPM in-house voltage stabiliser was connected in parallel to the internal battery. The voltage stabiliser consists of a set of two batteries, electrically protected from surcharge-discharge, easy to recharge and is designed to power two transfer standards for 10 consecutive days. At DEFNAT, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at DEFNAT, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by DEFNAT, at the level of 1.018 V and 10 V, at DEFNAT, UDEFNAT, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 26th of February 2016. UDEFNAT - UBIPM = + 0.07 μV uc = 0.04 μV, at 1.018 V UDEFNAT - UBIPM = + 0.38 μV uc = 0.10 μV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NSAI-NML, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which

Updating of working memory: lingering bindings.

PubMed

Oberauer, Klaus; Vockenberg, Kerstin

2009-05-01

Three experiments investigated proactive interference and proactive facilitation in a memory-updating paradigm. Participants remembered several letters or spatial patterns, distinguished by their spatial positions, and updated them by new stimuli up to 20 times per trial. Self-paced updating times were shorter when an item previously remembered and then replaced reappeared in the same location than when it reappeared in a different location. This effect demonstrates residual memory for no-longer-relevant bindings of items to locations. The effect increased with the number of items to be remembered. With one exception, updating times did not increase, and recall of final values did not decrease, over successive updating steps, thus providing little evidence for proactive interference building up cumulatively.

Bilateral comparison of 1 V and 10 V standards between the DMDM (Serbia) and the BIPM, January to March 2014 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Stock, M.; Pantelic-Babic, J.; Sofranac, Z.; Zivkovic, V.

2015-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1 V and 10 V voltage reference standards of the BIPM and the Directorate of Measures and Precious Metals (DMDM), Beograd, Serbia, was carried out from January to March 2014. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPM6 (Z6) and BIPMA (ZA), were transported by freight to DMDM. At DMDM, the reference standard for DC voltage is a Josephson Voltage Standard. The output electromotive force of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at DMDM, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and ambient atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by DMDM, at the level of 1.018 V and 10 V, at DMDM, UDMDM, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference date of the 13 February 2014. UDMDM - UBIPM = 0.094 µV uc = 0.072 µV, at 1 V UDMDM - UBIPM = 0.39 µV uc = 0.12 µV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at DMDM, based on KJ-90, and the uncertainty related to the comparison. The results at the 10 V level are not covered by the uncertainties with a coverage factor of 2. After the distribution of the Draft A, the DMDM discovered that the pressure gauge was defective. Some considerations on the correction to apply on the comparison result and the corresponding uncertainties are presented in the report. Nevertheless, the above results fully cover the CMCs of DMDM which are significantly larger. No corrections for temperature and pressure are applied in calibrations for

Afrotropical flea beetle genera: a key to their identification, updated catalogue and biogeographical analysis (Coleoptera, Chrysomelidae, Galerucinae, Alticini)

PubMed Central

Biondi, Maurizio; D’Alessandro, Paola

2012-01-01

Abstract A revision of the Alticini genera from the Afrotropical region is reported. The paper includes the following for the flea beetle fauna occurring in Sub-Saharan Africa and Madagascar: a key to their identification; habitus photos of all the genera; microscope and scanning electron micrographs of many diagnostic morphological characters; and an updated annotated catalogue with biogeographical notes that include new distributional data. The following new synonymies are proposed: Aphthona Chevrolat, 1836 = Ethiopia Scherer, 1972 syn. n.; Sanckia Duvivier, 1891 = Eugonotes Jacoby, 1897 syn. n.; Eurylegna Weise, 1910a = Eurylegniella Scherer, 1972 syn. n.; Kimongona Bechyné, 1959a = Mesocrepis Scherer, 1963 syn. n.; Diphaulacosoma Jacoby, 1892a = Neoderina Bechyné, 1952 syn. n.; Sesquiphaera Bechyné, 1958a = Paropsiderma Bechyné, 1958a syn. n.; Podagrica Chevrolat, 1836 = Podagricina Csiki in Heikertinger and Csiki 1940 syn. n.; Amphimela Chapuis, 1875 = Sphaerophysa Baly, 1876a syn. n. The following new combinations are proposed: Blepharida insignis Brancsik, 1897 = Xanthophysca insignis (Brancsik, 1897) comb. n.; Blepharida multiguttata Duvivier, 1891 = Xanthophysca multiguttata (Duvivier, 1891) comb. n.; Hemipyxis balyana (Csiki in Heikertinger and Csiki 1940) = Pseudadorium balyanum (Csiki in Heikertinger and Csiki, 1940) comb. n.; Hemipyxis brevicornis (Jacoby, 1892a) = Pseudadorium brevicornis (Jacoby, 1892a) comb. n.; Hemipyxis cyanea (Weise, 1910b) = Pseudadorium cyaneum (Weise, 1910b) comb. n.; Hemipyxis gynandromorpha Bechyné, 1958c = Pseudadorium gynandromorphum (Bechyné, 1958c) comb. n.; Hemipyxis latiuscula Bechyné, 1958c = Pseudadorium latiusculum (Bechyné, 1958c) comb. n.; Hemipyxis soror (Weise, 1910b) = Pseudadorium soror (Weise, 1910b) comb. n. The genera Buphonella Jacoby, 1903aand Halticopsis Fairmaire, 1883a are transferred to the tribe Galerucini; the genus Biodontocnema Biondi, 2000 stat. prom. is considered to be valid and

International comparison CCQM-K101: oxygen in nitrogen—a track B comparison and that the matrix contains argon

NASA Astrophysics Data System (ADS)

Zhou, Z.; Han, Q.; Wang, D.; Macé, T.; Kipphardt, H.; Maiwald, M.; Tuma, D.; Uehara, S.; Akima, D.; Shimosaka, T.; Jung, J.; Oh, S.-H.; van der Veen, A.; van Wijk, J. I. T.; Ziel, P. R.; Konopelko, L.; Valkova, M.; Mogale, David M.; Botha, A.; Brewer, P.; Murugan, A.; Doval Minnaro, M.; Miller, M.; Guenther, F.; Kelly, M. E.

2016-01-01

This key comparison aims to assess the capabilities of the participants to determine the amount-of-substance fraction oxygen in nitrogen. The GAWG has classified this as a track B comparison, due to the unexpected 50 μmol/mol argon mole fraction content of the transfer standards, which effects the achievable performance of some measurement techniques such a GC-TCD. The separation of oxygen and argon is challenging, and not all systems in use are equally well designed for it. As this analytical challenge due to a substantial fraction of argon in the transfer standards became a reality, the Gas Analysis Working Group (GAWG) decided to qualify this key comparison as a regular key comparison and not as a core comparison, which may be used to support calibration and measurement capabilities (CMCs) for oxygen in nitrogen, or for oxygen in nitrogen mixtures containing argon only (see also the section on support to CMCs). Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Lack of Set Size Effects in Spatial Updating: Evidence for Offline Updating

ERIC Educational Resources Information Center

Hodgson, Eric; Waller, David

2006-01-01

Four experiments required participants to keep track of the locations of (i.e., update) 1, 2, 3, 4, 6, 8, 10, or 15 target objects after rotating. Across all conditions, updating was unaffected by set size. Although some traditional set size effects (i.e., a linear increase of latency with memory load) were observed under some conditions, these…

The Evaluation of Vehicle Mass Reduction and Material Choice in Life Cycle Assessments: Key Factors and Dynamic Industries

EPA Science Inventory

Developments in the realm of lightweight materials for automotive use continue to be announced by the industry and by academia. This session will provide new and updated information on new generation of materials. Additionally, this session will focus on the key topics involved i...

49 CFR 1002.3 - Updating user fees.

Code of Federal Regulations, 2010 CFR

2010-10-01

... updating fees. Each fee shall be updated by updating the cost components comprising the fee. Cost... direct labor costs are direct labor costs determined by the cost study set forth in Revision of Fees For... by total office costs for the Offices directly associated with user fee activity. Actual updating of...

Updating during reading comprehension: why causality matters.

PubMed

Kendeou, Panayiota; Smith, Emily R; O'Brien, Edward J

2013-05-01

The present set of 7 experiments systematically examined the effectiveness of adding causal explanations to simple refutations in reducing or eliminating the impact of outdated information on subsequent comprehension. The addition of a single causal-explanation sentence to a refutation was sufficient to eliminate any measurable disruption in comprehension caused by the outdated information (Experiment 1) but was not sufficient to eliminate its reactivation (Experiment 2). However, a 3 sentence causal-explanation addition to a refutation eliminated both any measurable disruption in comprehension (Experiment 3) and the reactivation of the outdated information (Experiment 4). A direct comparison between the 1 and 3 causal-explanation conditions provided converging evidence for these findings (Experiment 5). Furthermore, a comparison of the 3 sentence causal-explanation condition with a 3 sentence qualified-elaboration condition demonstrated that even though both conditions were sufficient to eliminate any measurable disruption in comprehension (Experiment 6), only the causal-explanation condition was sufficient to eliminate the reactivation of the outdated information (Experiment 7). These results establish a boundary condition under which outdated information will influence comprehension; they also have broader implications for both the updating process and knowledge revision in general.

agriGO v2.0: a GO analysis toolkit for the agricultural community, 2017 update.

PubMed

Tian, Tian; Liu, Yue; Yan, Hengyu; You, Qi; Yi, Xin; Du, Zhou; Xu, Wenying; Su, Zhen

2017-07-03

The agriGO platform, which has been serving the scientific community for >10 years, specifically focuses on gene ontology (GO) enrichment analyses of plant and agricultural species. We continuously maintain and update the databases and accommodate the various requests of our global users. Here, we present our updated agriGO that has a largely expanded number of supporting species (394) and datatypes (865). In addition, a larger number of species have been classified into groups covering crops, vegetables, fish, birds and insects closely related to the agricultural community. We further improved the computational efficiency, including the batch analysis and P-value distribution (PVD), and the user-friendliness of the web pages. More visualization features were added to the platform, including SEACOMPARE (cross comparison of singular enrichment analysis), direct acyclic graph (DAG) and Scatter Plots, which can be merged by choosing any significant GO term. The updated platform agriGO v2.0 is now publicly accessible at http://systemsbiology.cau.edu.cn/agriGOv2/. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

agriGO v2.0: a GO analysis toolkit for the agricultural community, 2017 update

PubMed Central

Tian, Tian; Liu, Yue; Yan, Hengyu; You, Qi; Yi, Xin; Du, Zhou

2017-01-01

Abstract The agriGO platform, which has been serving the scientific community for >10 years, specifically focuses on gene ontology (GO) enrichment analyses of plant and agricultural species. We continuously maintain and update the databases and accommodate the various requests of our global users. Here, we present our updated agriGO that has a largely expanded number of supporting species (394) and datatypes (865). In addition, a larger number of species have been classified into groups covering crops, vegetables, fish, birds and insects closely related to the agricultural community. We further improved the computational efficiency, including the batch analysis and P-value distribution (PVD), and the user-friendliness of the web pages. More visualization features were added to the platform, including SEACOMPARE (cross comparison of singular enrichment analysis), direct acyclic graph (DAG) and Scatter Plots, which can be merged by choosing any significant GO term. The updated platform agriGO v2.0 is now publicly accessible at http://systemsbiology.cau.edu.cn/agriGOv2/. PMID:28472432

Updating Sea Spray Aerosol Emissions in the Community Multiscale Air Quality Model

NASA Astrophysics Data System (ADS)

Gantt, B.; Bash, J. O.; Kelly, J.

2014-12-01

Sea spray aerosols (SSA) impact the particle mass concentration and gas-particle partitioning in coastal environments, with implications for human and ecosystem health. In this study, the Community Multiscale Air Quality (CMAQ) model is updated to enhance fine mode SSA emissions, include sea surface temperature (SST) dependency, and revise surf zone emissions. Based on evaluation with several regional and national observational datasets in the continental U.S., the updated emissions generally improve surface concentrations predictions of primary aerosols composed of sea-salt and secondary aerosols affected by sea-salt chemistry in coastal and near-coastal sites. Specifically, the updated emissions lead to better predictions of the magnitude and coastal-to-inland gradient of sodium, chloride, and nitrate concentrations at Bay Regional Atmospheric Chemistry Experiment (BRACE) sites near Tampa, FL. Including SST-dependency to the SSA emission parameterization leads to increased sodium concentrations in the southeast U.S. and decreased concentrations along the Pacific coast and northeastern U.S., bringing predictions into closer agreement with observations at most Interagency Monitoring of Protected Visual Environments (IMPROVE) and Chemical Speciation Network (CSN) sites. Model comparison with California Research at the Nexus of Air Quality and Climate Change (CalNex) observations will also be discussed, with particular focus on the South Coast Air Basin where clean marine air mixes with anthropogenic pollution in a complex environment. These SSA emission updates enable more realistic simulation of chemical processes in coastal environments, both in clean marine air masses and mixtures of clean marine and polluted conditions.

Efficacy of interventions to combat tobacco addiction: Cochrane update of 2012 reviews.

PubMed

Hartmann-Boyce, Jamie; Stead, Lindsay F; Cahill, Kate; Lancaster, Tim

2013-10-01

The Cochrane Collaboration is an international not-for-profit organization which produces and disseminates systematic reviews of health-care interventions. This paper is the first in a series of annual updates of Cochrane reviews on tobacco addiction interventions. It also provides an up-to-date overview of review findings in this area to date and summary statistics for cessation reviews in which meta-analyses were conducted. In 2012, the Group published seven new reviews and updated 13 others. This update summarizes and comments on these reviews. It also summarizes key findings from all the other reviews in this area. New reviews in 2012 found that in smokers using pharmacotherapy, behavioural support improves success rates [risk ratio (RR) 1.16, 95% confidence interval (CI) = 1.09-1.24], and that combining behavioural support and pharmacotherapy aids cessation (RR 1.82, 95% CI = 1.66-2.00). Updated reviews established mobile phones as potentially helpful in aiding cessation (RR 1.71, 95% CI = 1.47-1.99), found that cytisine (RR 3.98, 95% CI = 2.01-7.87) and low-dose varenicline (RR 2.09, 95% CI = 1.56-2.78) aid smoking cessation, and found that training health professionals in smoking cessation improves patient cessation rates (RR 1.60, 95% CI = 1.26-2.03). The updated reviews confirmed the benefits of nicotine replacement therapy, standard dose varenicline and providing cessation treatment free of charge. Lack of demonstrated efficacy remained for partner support, expired-air carbon monoxide feedback and lung function feedback. Cochrane systematic review evidence for the first time establishes the efficacy of behavioural support over and above pharmacotherapy, as well as the efficacy of cytisine, mobile phone technology, low-dose varenicline and health professional training in promoting smoking cessation. © 2013 Society for the Study of Addiction.

Country Update: Israel 2005

ERIC Educational Resources Information Center

Marar, Marianne Maurice

2005-01-01

Country Updates is a new section of "Intercultural Education." Starting in "Intercultural Education," Volume 16 No. 5, this column will focus on recent developments during the last two to three years in the field of intercultural education in one particular country. These updates can include recent policy decisions, the main…

78 FR 51073 - Product List Update

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-20

... POSTAL REGULATORY COMMISSION 39 CFR Part 3020 [Docket Nos. MC2012-49, et al.] Product List Update... competitive product list. This action reflects the disposition of recent dockets, as reflected in Commission... updates. The updates are identified in the body of this document. The product lists, which are republished...

Automatic updating and 3D modeling of airport information from high resolution images using GIS and LIDAR data

NASA Astrophysics Data System (ADS)

Lv, Zheng; Sui, Haigang; Zhang, Xilin; Huang, Xianfeng

2007-11-01

As one of the most important geo-spatial objects and military establishment, airport is always a key target in fields of transportation and military affairs. Therefore, automatic recognition and extraction of airport from remote sensing images is very important and urgent for updating of civil aviation and military application. In this paper, a new multi-source data fusion approach on automatic airport information extraction, updating and 3D modeling is addressed. Corresponding key technologies including feature extraction of airport information based on a modified Ostu algorithm, automatic change detection based on new parallel lines-based buffer detection algorithm, 3D modeling based on gradual elimination of non-building points algorithm, 3D change detecting between old airport model and LIDAR data, typical CAD models imported and so on are discussed in detail. At last, based on these technologies, we develop a prototype system and the results show our method can achieve good effects.

KEY COMPARISON: Final report on CCQM-K63.a,b: Non-peptide hormones in serum: cortisol and progesterone

NASA Astrophysics Data System (ADS)

S-C Tai, Susan; Duewer, David L.

2010-01-01

Hormones are chemical messengers that regulate many life functions. Deviations from normal hormone levels can have serious health consequences. Accurate measurement of hormone levels in serum can be beneficial in diagnosing, monitoring, and treating a number of diseases. Two steroid hormones, cortisol and progesterone, were selected by the Organic Analysis Working Group (OAWG) to evaluate its member Institutes' measurement capabilities for this important class of measurand. Serum concentrations of cortisol range from 30 ng/mL to 230 ng/mL. Serum concentrations of progesterone in adult females range from 0.15 ng/mL to 25 ng/mL but can rise to approx230 ng/mL during pregnancy. The ability to measure cortisol is indicative of a laboratory's ability to measure steroid hormones at concentration levels similar to cortisol. The ability to measure progesterone is indicative of a laboratory's ability to measure steroid hormones with similar functional groups and concentration levels, such as testosterone. Pilot studies CCQM-P77.a and CCQM-P77.b on the determination of cortisol and progesterone in human serum were completed in 2006. There was good agreement among the results reported by participants who used isotope dilution/mass spectrometry (ID/MS) with either gas chromatography (GC) or liquid chromatography (LC). In 2007 the OAWG decided to proceed with key comparison (KC) CCQM-K63.a, cortisol in human serum, and CCQM-K63.b, progesterone in human serum. Thus, following established OAWG procedure, only results from participants that (1) used an ID/MS-based method, (2) participated in the relevant pilot study, and (3) used a metrologically traceable primary standard were to be eligible for use in calculating the key comparison reference value (KCRV) for each measurand. Six laboratories participated in CCQM-K63.a and eight laboratories participated in CCQM-K63.b. The same pooled frozen female serum material was used in both of the KCs. The mean value for the six ID

Testing necessary regional frontal contributions to value assessment and fixation-based updating.

PubMed

Vaidya, Avinash R; Fellows, Lesley K

2015-12-14

Value-based decisions are biased by the time people spend viewing each option: Options fixated longer are chosen more often, even when previously rated as less appealing. This bias is thought to reflect 'value updating' as new evidence is accumulated. Prior work has shown that ventromedial prefrontal cortex (PFC) carries a fixation-dependent value comparison signal, while other studies implicate dorsomedial PFC in representing the value of alternative options. Here, we test whether these regions are necessary for fixation-related value updating in 33 people with frontal lobe damage and 27 healthy controls performing a simple choice task. We show that damage to dorsomedial PFC leads to an exaggerated influence of fixations on choice, while damage to ventromedial or lateral PFC has no effect on this bias. These findings suggest a critical role for dorsomedial, and not ventromedial PFC, in mediating the relative influence of current fixations and a priori value on choice.

Updating Landsat-derived land-cover maps using change detection and masking techniques

NASA Technical Reports Server (NTRS)

Likens, W.; Maw, K.

1982-01-01

The California Integrated Remote Sensing System's San Bernardino County Project was devised to study the utilization of a data base at a number of jurisdictional levels. The present paper discusses the implementation of change-detection and masking techniques in the updating of Landsat-derived land-cover maps. A baseline landcover classification was first created from a 1976 image, then the adjusted 1976 image was compared with a 1979 scene by the techniques of (1) multidate image classification, (2) difference image-distribution tails thresholding, (3) difference image classification, and (4) multi-dimensional chi-square analysis of a difference image. The union of the results of methods 1, 3 and 4 was used to create a mask of possible change areas between 1976 and 1979, which served to limit analysis of the update image and reduce comparison errors in unchanged areas. The techniques of spatial smoothing of change-detection products, and of combining results of difference change-detection algorithms are also shown to improve Landsat change-detection accuracies.

Final report on EURAMET.M.P-K4.2010: Key and supplementary comparison of national pressure standards in the range 1 Pa to 15 kPa of absolute and gauge pressure

NASA Astrophysics Data System (ADS)

Krajíček, Zdeněk; Bergoglio, Mercede; Jousten, Karl; Otal, Pierre; Sabuga, Wladimir; Saxholm, Sari; Pražák, Dominik; Vičar, Martin

2014-01-01

This report describes a EURAMET comparison of five European National Metrology Institutes in low gauge and absolute pressure in gas (nitrogen), denoted as EURAMET.M.P-K4.2010. Its main intention is to state equivalence of the pressure standards, in particular those based on the technology of force-balanced piston gauges such as e.g. FRS by Furness Controls, UK and FPG8601 by DHI-Fluke, USA. It covers the range from 1 Pa to 15 kPa, both gauge and absolute. The comparison in absolute mode serves as a EURAMET Key Comparison which can be linked to CCM.P-K4 and CCM.P-K2 via PTB. The comparison in gauge mode is a supplementary comparison. The comparison was carried out from September 2008 till October 2012. The participating laboratories were the following: CMI, INRIM, LNE, MIKES, PTB-Berlin (absolute pressure 1 kPa and below) and PTB-Braunschweig (absolute pressure 1 kPa and above and gauge pressure). CMI was the pilot laboratory and provided a transfer standard for the comparison. This transfer standard was also the laboratory standard of CMI at the same time, which resulted in a unique and logistically difficult star comparison. Both in gauge and absolute pressures all the participating institutes successfully proved their equivalence with respect to the reference value and all also proved mutual bilateral equivalences in all the points. All the participating laboratories are also equivalent with the reference values of CCM.P-K4 and CCM.P-K2 in the relevant points. The comparison also proved the ability of FPG8601 to serve as a transfer standard. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Fishes of the Cusiana River (Meta River basin, Colombia), with an identification key to its species

PubMed Central

Urbano-Bonilla, Alexander; Ballen, Gustavo A.; Herrera-R, Guido A.; Jhon Zamudio; Herrera-Collazos, Edgar E.; DoNascimiento, Carlos; Saúl Prada-Pedreros; Maldonado-Ocampo, Javier A.

2018-01-01

Abstract The Cusiana River sub-basin has been identified as a priority conservation area in the Orinoco region in Colombia due to its high species diversity. This study presents an updated checklist and identification key for fishes of the Cusiana River sub-basin. The checklist was assembled through direct examination of specimens deposited in the main Colombian ichthyological collections. A total of 2020 lots from 167 different localities from the Cusiana River sub-basin were examined and ranged from 153 to 2970 m in elevation. The highest number of records were from the piedmont region (1091, 54.0 %), followed by the Llanos (878, 43.5 %) and Andean (51, 2.5 %). 241 species distributed in 9 orders, 40 families, and 158 genera were found. The fish species richness observed (241), represents 77.7 % of the 314 estimated species (95 % CI=276.1–394.8). The use of databases to develop lists of fish species is not entirely reliable; therefore taxonomic verification of specimens in collections is essential. The results will facilitate comparisons with other sub-basins of the Orinoquia, which are not categorized as areas of importance for conservation in Colombia. PMID:29416408

WHO Treatment Guidelines for Drug-Resistant Tuberculosis, 2016 Update: Applicability in South Korea

PubMed Central

2017-01-01

Despite progress made in tuberculosis control worldwide, the disease burden and treatment outcome of multidrug-resistant tuberculosis (MDR-TB) patients have remained virtually unchanged. In 2016, the World Health Organization released new guidelines for the management of MDR-TB. The guidelines are intended to improve detection rate and treatment outcome for MDR-TB through novel, rapid molecular testing and shorter treatment regimens. Key changes include the introduction of a new, shorter MDR-TB treatment regimen, a new classification of medicines and updated recommendations for the conventional MDR-TB regimen. This paper will review these key changes and discuss the potential issues with regard to the implementation of these guidelines in South Korea. PMID:28905529

SERC 2014 2018 Technical Plan: 2016 Update

DTIC Science & Technology

2016-02-18

Contract Number: HQ0034-13-D-0004 February 18, 2016 SERC 2014-2018 Technical Plan Update SERC 2014-2018 Technical Plan: 2016 Update...UNCLASSIFIED / APPROVED FOR PUBLIC RELEASE Contract Number: HQ0034-13-D-0004 February 18, 2016 SERC 2014-2018 Technical Plan Update ii...18, 2016 SERC 2014-2018 Technical Plan Update iii TABLE OF CONTENTS Table of Contents

Extravasation management: clinical update.

PubMed

Schulmeister, Lisa

2011-02-01

To present a clinical update on the prevention, detection, and evidence-based management of vesicant chemotherapy extravasations. Journal articles, published and unpublished case reports, personal experience. In the 4 years that have elapsed since the publication of the original article, much more is known about vesicant chemotherapy extravasation, and effective evidence-based treatments now are available. The antidotes sodium thiosulfate for mechlorethamine extravasations and hyaluronidase for plant alkaloid extravasations are recommended by the manufacturers of these vesicants and cited in nursing guidelines. The anthracycline extravasation treatment dexrazoxane for injection, the first and only extravasation treatment with proven effectiveness, is now available as Totect (dexrazoxane; TopoTarget USA, Rockaway, NJ, USA) in the US and Savene (SpePharm, Amsterdam, The Netherlands) in Europe. Nurses who administer vesicant chemotherapy agents need to be aware of the most current evidence (or lack of evidence) for various types of extravasation treatment. Well-informed nurses are patient advocates and instrumental in detecting, managing, and documenting extravasations. Most importantly, nurses play a key role in preventing vesicant chemotherapy extravasations. Copyright © 2011 Elsevier Inc. All rights reserved.

Bilateral comparison of 1 V and 10 V standards between the NMISA (South Africa) and the BIPM April to June 2017 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

NASA Astrophysics Data System (ADS)

Solve, S.; Chayramy, R.; Matlejoane, A. M.; Magagula, L.; Stock, M.

2018-01-01

As part of the ongoing BIPM key comparison BIPM.EM-K11.a and b, a comparison of the 1.018 V and 10 V voltage reference standards of the BIPM and the National Metrology Institute of South Africa, NMISA (South Africa), was carried out from April to June 2017. Two BIPM Zener diode-based travelling standards (Fluke 732B), BIPMA (ZA) and BIPMB (ZB), were transported by freight to NMISA and back to BIPM. In order to keep the Zeners powered during their transportation phase, a voltage stabilizer developed by BIPM was connected in parallel to the internal battery. It consists of a set of two batteries, electrically protected from surcharge-discharge, easy to recharge and is designed to power two transfer standards for ten consecutive days. At NMISA, the reference standard for DC voltage is a Josephson Voltage Standard. The output EMF (Electromotive Force) of each travelling standard was measured by direct comparison with the primary standard. At the BIPM, the travelling standards were calibrated, before and after the measurements at NMISA, with the Josephson Voltage Standard. Results of all measurements were corrected for the dependence of the output voltages of the Zener standards on internal temperature and atmospheric pressure. The final result of the comparison is presented as the difference between the values assigned to DC voltage standards by NMISA, at the level of 1.018 V and 10 V, at NMISA, UNMISA, and those assigned by the BIPM, at the BIPM, UBIPM, at the reference dates of the 19th and 18th of May 2017, respectively. UNMISA - UBIPM = + 0.07 μV uc = 0.02 μV, at 1.018 V UNMISA - UBIPM = + 0.001 μV uc = 0.34 μV, at 10 V where uc is the combined standard uncertainty associated with the measured difference, including the uncertainty of the representation of the volt at the BIPM and at NMISA, based on KJ-90, and the uncertainty related to the comparison. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which

A Third Species of Hemilecanium Newstead (Hemiptera: Coccoidea: Coccidae) from the New World, with Keys to Species in the Genus.

PubMed

Kondo, T; Hodgson, C

2013-10-01

A new species of Hemilecanium Newstead, Hemilecanium guanabana Kondo & Hodgson n. sp., is described and illustrated based on the adult female, adult male and first instar. The specimens were collected in the municipality of Palmira, state of Valle del Cauca, Colombia, on soursop, Annona muricata (Annonaceae). Updated identification keys are provided for the adult females of all 28 species of the genus Hemilecanium, and for known adult males and first instars. An updated list of the 23 species of soft scales (Coccidae) known from soursop worldwide is included.

Discovery-2: an interactive resource for the rational selection and comparison of putative drug target proteins in malaria

PubMed Central

2013-01-01

Background Drug resistance to anti-malarial compounds remains a serious problem, with resistance to newer pharmaceuticals developing at an alarming rate. The development of new anti-malarials remains a priority, and the rational selection of putative targets is a key element of this process. Discovery-2 is an update of the original Discovery in silico resource for the rational selection of putative drug target proteins, enabling researchers to obtain information for a protein which may be useful for the selection of putative drug targets, and to perform advanced filtering of proteins encoded by the malaria genome based on a series of molecular properties. Methods An updated in silico resource has been developed where researchers are able to mine information on malaria proteins and predicted ligands, as well as perform comparisons to the human and mosquito host characteristics. Protein properties used include: domains, motifs, EC numbers, GO terms, orthologs, protein-protein interactions, protein-ligand interactions. Newly added features include drugability measures from ChEMBL, automated literature relations and links to clinical trial information. Searching by chemical structure is also available. Results The updated functionality of the Discovery-2 resource is presented, together with a detailed case study of the Plasmodium falciparum S-adenosyl-L-homocysteine hydrolase (PfSAHH) protein. A short example of a chemical search with pyrimethamine is also illustrated. Conclusion The updated Discovery-2 resource allows researchers to obtain detailed properties of proteins from the malaria genome, which may be of interest in the target selection process, and to perform advanced filtering and selection of proteins based on a relevant range of molecular characteristics. PMID:23537208

HFE Process Guidance and Standards for potential application to updating NRC guidance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jacques Hugo; J. J. Persensky

2012-07-01

The U.S. Nuclear Regulatory Commission (NRC) reviews and evaluates the human factors engineering (HFE) programs of applicants for nuclear power plant construction permits, operating licenses, standard design certifications, and combined operating licenses. The purpose of these safety reviews is to help ensure that personnel performance and reliability are appropriately supported. Detailed design review procedures and guidance for the evaluations is provided in three key documents: the Standard Review Plan (NUREG-0800), the HFE Program Review Model (NUREG-0711), and the Human-System Interface Design Review Guidelines (NUREG-0700). These documents were last revised in 2007, 2004 and 2002, respectively. The NRC is committed tomore » the periodic update and improvement of these guidance documents to ensure that they remain state-of-the-art design evaluation tools. Thus, the NRC has initiated a project with BNL to update the NRC guidance to remain current with recent research on human performance, advances in HFE methods and tools, and new technology. INL supported Brookhaven National Lab (BNL) to update the detailed HFE review criteria contained in NUREG-0711 and NUREG-0700 based on (1) feedback obtained from end users, (2) the results of NRC research and development efforts supporting the NRC staff’s HFE safety reviews, and (3) other material the project staff identify as applicable to the update effort. INL submitted comments on development plans and sections of NUREGs 0800, 0711, and 0700. The contractor prepared the report attached here as the deliverable for this work.« less

Updating and feature overwriting in short-term memory for timbre.

PubMed

Mercer, Tom; McKeown, Denis

2010-11-01

Previous research has demonstrated a potent, stimulus-specific form of interference in short-term auditory memory. This effect has been interpreted in terms of interitem confusion and grouping, but the present experiments suggested that interference might be a feature-specific phenomenon. Participants compared standard and comparison tones over a 10-sec interval and were required to determine whether they differed in timbre. A single interfering distractor tone was presented either 50 msec or 8 sec after the offset of the standard (Experiment 1) or 2 sec prior to its onset (Experiment 2). The distractor varied in the number of features it shared with the standard and comparison, and this proved critical, since performance on the task was greatly impaired when the distractor either consisted of novel, unshared features (Experiment 1) or contained the distinguishing feature of the comparison tone (Experiments 1 and 2). These findings were incompatible with earlier accounts of forgetting but were fully explicable by the recent timbre memory model, which associates interference in short-term auditory memory with an "updating" process and feature overwriting. These results suggest similarities with the mechanisms that underlie forgetting in verbal short-term memory.

EURAMET key comparison no. EURAMET.T-K1: realisations of the ITS-90 from 2.6 K to 24.5561 K, using rhodium-iron resistance thermometers

NASA Astrophysics Data System (ADS)

Gaiser, Christof; Fellmuth, Bernd; Steur, Peter; Szmyrka-Grzebyk, Anna; Manuszkiewicz, Henryk; Lipinski, Leszek; Peruzzi, Andrea; Rusby, Richard; Head, David

2017-01-01

In the temperature range from 0.65 K to 24.5561 K, the ITS-90 is defined by specified vapour-pressure equations for 3He and 4He and interpolation equations for a constant-volume gas thermometer using 3He or 4He. The definitions are given in sections 3.1 and 3.2 of the ITS-90 text, and methods for realising the scale in this range are outlined in chapters 4 and 5 of the Guide to the Realization of the ITS-90 (formerly Supplementary Information for the ITS-90). Direct realisations of the ITS-90 by these methods require relatively sophisticated apparatus and time-consuming experiments, and consequently they are rarely carried out. The situation is acceptable in practice only because rhodium-iron resistance thermometers (RIRTs) are available that, once calibrated, are able to maintain their calibrations reliably for long periods of time. They are the practical thermometers on which realisations of the ITS-90 are most accurately maintained, disseminated and compared. The key comparison EURAMET.T-K1 is therefore a comparison of calibrated RIRTs. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

34 CFR 668.55 - Updating information.

Code of Federal Regulations, 2011 CFR

2011-07-01

... information to be updated has taken place since the last update. (3) If, as a result of a change in the... section apply, an applicant is required to update— (i) The number of family members in the applicant's... changes, the applicant shall not update those factors or that status. (b) If the number of family members...

Comparison of different incremental analysis update schemes in a realistic assimilation system with Ensemble Kalman Filter

NASA Astrophysics Data System (ADS)

Yan, Y.; Barth, A.; Beckers, J. M.; Brankart, J. M.; Brasseur, P.; Candille, G.

2017-07-01

In this paper, three incremental analysis update schemes (IAU 0, IAU 50 and IAU 100) are compared in the same assimilation experiments with a realistic eddy permitting primitive equation model of the North Atlantic Ocean using the Ensemble Kalman Filter. The difference between the three IAU schemes lies on the position of the increment update window. The relevance of each IAU scheme is evaluated through analyses on both thermohaline and dynamical variables. The validation of the assimilation results is performed according to both deterministic and probabilistic metrics against different sources of observations. For deterministic validation, the ensemble mean and the ensemble spread are compared to the observations. For probabilistic validation, the continuous ranked probability score (CRPS) is used to evaluate the ensemble forecast system according to reliability and resolution. The reliability is further decomposed into bias and dispersion by the reduced centred random variable (RCRV) score. The obtained results show that 1) the IAU 50 scheme has the same performance as the IAU 100 scheme 2) the IAU 50/100 schemes outperform the IAU 0 scheme in error covariance propagation for thermohaline variables in relatively stable region, while the IAU 0 scheme outperforms the IAU 50/100 schemes in dynamical variables estimation in dynamically active region 3) in case with sufficient number of observations and good error specification, the impact of IAU schemes is negligible. The differences between the IAU 0 scheme and the IAU 50/100 schemes are mainly due to different model integration time and different instability (density inversion, large vertical velocity, etc.) induced by the increment update. The longer model integration time with the IAU 50/100 schemes, especially the free model integration, on one hand, allows for better re-establishment of the equilibrium model state, on the other hand, smooths the strong gradients in dynamically active region.

Endogenous-cue prospective memory involving incremental updating of working memory: an fMRI study.

PubMed

Halahalli, Harsha N; John, John P; Lukose, Ammu; Jain, Sanjeev; Kutty, Bindu M

2015-11-01

Prospective memory paradigms are conventionally classified on the basis of event-, time-, or activity-based intention retrieval. In the vast majority of such paradigms, intention retrieval is provoked by some kind of external event. However, prospective memory retrieval cues that prompt intention retrieval in everyday life are commonly endogenous, i.e., linked to a specific imagined retrieval context. We describe herein a novel prospective memory paradigm wherein the endogenous cue is generated by incremental updating of working memory, and investigated the hemodynamic correlates of this task. Eighteen healthy adult volunteers underwent functional magnetic resonance imaging while they performed a prospective memory task where the delayed intention was triggered by an endogenous cue generated by incremental updating of working memory. Working memory and ongoing task control conditions were also administered. The 'endogenous-cue prospective memory condition' with incremental working memory updating was associated with maximum activations in the right rostral prefrontal cortex, and additional activations in the brain regions that constitute the bilateral fronto-parietal network, central and dorsal salience networks as well as cerebellum. In the working memory control condition, maximal activations were noted in the left dorsal anterior insula. Activation of the bilateral dorsal anterior insula, a component of the central salience network, was found to be unique to this 'endogenous-cue prospective memory task' in comparison to previously reported exogenous- and endogenous-cue prospective memory tasks without incremental working memory updating. Thus, the findings of the present study highlight the important role played by the dorsal anterior insula in incremental working memory updating that is integral to our endogenous-cue prospective memory task.

Taxonomic update on proposed nomenclature and classification changes for bacteria of medical importance, 2015.

PubMed

Janda, J Michael

2016-10-01

A key aspect of medical, public health, and diagnostic microbiology laboratories is the accurate and rapid reporting and communication regarding infectious agents of clinical significance. Microbial taxonomy in the age of molecular diagnostics and phylogenetics creates changes in taxonomy at a rapid rate further complicating this process. This update focuses on the description of new species and classification changes proposed in 2015. Copyright © 2016 Elsevier Inc. All rights reserved.

Update on progress in HIV vaccine development.

PubMed

Watkins, David I

2012-01-01

The 19th Conference on Retroviruses and Opportunistic Infections heralded the arrival of a new crop of potent, broadly neutralizing antibodies against HIV. This advance has given the entire vaccine field enormous hope that it will be possible one day to develop an antibody-based vaccine for HIV. However, substantial obstacles still exist in the induction of these antibodies by vaccination, given the enormous number of somatic mutations needed to develop these highly efficient antibodies. It is likely that follicular helper T cells will be involved in the development of these antibodies, and this will be a key area of interest in the future. Cellular immune responses will also be an important part of any vaccine regimen. Evidence showed that protection provided by an attenuated vaccine correlated with the frequency of vaccine-induced helper cells and killer cells, underlining the importance of these key immune cells. An alternative approach to the development of potent neutralizing antibodies was presented as part of an update on the Thai Phase III Vaccine Trial RV144. Data were shown suggesting that binding antibodies may play a role in protection from HIV infection.

International comparison Euramet.QM-K111—propane in nitrogen

NASA Astrophysics Data System (ADS)

Wouter van der Hout, J.; van der Veen, Adriaan M. H.; Ziel, Paul R.; Kipphardt, Heinrich; Tuma, Dirk; Maiwald, Michael; Fernández, Teresa E.; Gómez, Concepción; Cieciora, Dariusz; Ochman, Grzegorz; Dias, Florbela; Silvino, Victor; Macé, Tatiana; Sutour, Christophe; Marioni, Fabrice; Ackermann, Andreas; Niederhauser, Bernhard; Fükő, Judit; Büki, Tamás; Nagyné Szilágyi, Zsófia; Tarhan, Tanıl; Engin, Erinç

2017-01-01

This key comparison aims to assess the core capabilities of the participants in gas analysis. Such competences include, among others, the capabilities to prepare Primary Standard gas Mixtures (PSMs), perform the necessary purity analysis on the materials used in the gas mixture preparation, the verification of the composition of newly prepared PSMs against existing ones, and the capability of calibrating the composition of a gas mixture. According to the Strategy for Key Comparisons of the Gas Analysis Working Group, this key comparison is classified as an RMO track A key comparison. The artefacts were binary mixtures of propane in nitrogen at a nominal amount-of-substance fraction level of 1000 μmol/mol. The values and uncertainties from the gravimetric gas mixture preparation were used as key comparison reference values (KCRVs). Each transfer standard had its own KCRV. The results are generally good. All results are within +/- 1 % of the KCRV. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCQM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

XFEM-based modeling of successive resections for preoperative image updating

NASA Astrophysics Data System (ADS)

Vigneron, Lara M.; Robe, Pierre A.; Warfield, Simon K.; Verly, Jacques G.

2006-03-01

We present a new method for modeling organ deformations due to successive resections. We use a biomechanical model of the organ, compute its volume-displacement solution based on the eXtended Finite Element Method (XFEM). The key feature of XFEM is that material discontinuities induced by every new resection can be handled without remeshing or mesh adaptation, as would be required by the conventional Finite Element Method (FEM). We focus on the application of preoperative image updating for image-guided surgery. Proof-of-concept demonstrations are shown for synthetic and real data in the context of neurosurgery.

BI-RADS update.

PubMed

Mercado, Cecilia L

2014-05-01

The updated American College of Radiology (ACR) Breast Imaging Reporting and Data System (BI-RADS) has been newly released. This article summarizes the changes and updates that have been made to BI-RADS. The goal of the revised edition continues to be the same: to improve clarification in image interpretation, maintain reporting standardization, and simplify the monitoring of outcomes. The new BI-RADS also introduces new terminology to provide a more universal lexicon across all 3 imaging modalities. Copyright © 2014 Elsevier Inc. All rights reserved.

Arctic Freshwater Synthesis: Summary of key emerging issues

NASA Astrophysics Data System (ADS)

Prowse, T.; Bring, A.; Mârd, J.; Carmack, E.; Holland, M.; Instanes, A.; Vihma, T.; Wrona, F. J.

2015-10-01

In response to a joint request from the World Climate Research Program's Climate and Cryosphere Project, the International Arctic Science Committee, and the Arctic Council's Arctic Monitoring and Assessment Program an updated scientific assessment has been conducted of the Arctic Freshwater System (AFS), entitled the Arctic Freshwater Synthesis (AFSΣ). The major reason behind the joint request was an increasing concern that changes to the AFS have produced, and could produce even greater, changes to biogeophysical and socioeconomic systems of special importance to northern residents and also produce extra-Arctic climatic effects that will have global consequences. The AFSΣ was structured around six key thematic areas: atmosphere, oceans, terrestrial hydrology, terrestrial ecology, resources, and modeling, the review of each coauthored by an international group of scientists and published as separate manuscripts in this special issue of Journal of Geophysical Research-Biogeosciences. This AFSΣ summary manuscript reviews key issues that emerged during the conduct of the synthesis, especially those that are cross-thematic in nature, and identifies future research required to address such issues.

Capital update factor: a new era approaches.

PubMed

Grimaldi, P L

1993-02-01

The Health Care Financing Administration (HCFA) has constructed a preliminary model of a new capital update method which is consistent with the framework being developed to refine the update method for PPS operating costs. HCFA's eventual goal is to develop a single update framework for operating and capital costs. Initial results suggest that adopting the new capital update method would reduce capital payments substantially, which might intensify creditor's concerns about extending loans to hospitals.

The updated billion-ton resource assessment

Treesearch

Anthony Turhollow; Robert Perlack; Laurence Eaton; Matthew Langholtz; Craig Brandt; Mark Downing; Lynn Wright; Kenneth Skog; Chad Hellwinckel; Bryce Stokes; Patricia Lebow

2014-01-01

This paper summarizes the results of an update to a resource assessment, published in 2005, commonly referred to as the Billion-Ton Study (BTS). The updated results are consistent with the 2005 BTS in terms of overall magnitude. The 2005 BTS projected between 860 and 1240 Tg of biomass available in the 2050 timeframe, while the Billion-Ton Update (BT2), for a price of...

Multipartite interacting scalar dark matter in the light of updated LUX data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharya, Subhaditya; Ghosh, Purusottam; Poulose, Poulose, E-mail: subhab@iitg.ernet.in, E-mail: p.ghosh@iitg.ernet.in, E-mail: poulose@iitg.ernet.in

2017-04-01

We explore constraints on multipartite dark matter (DM) framework composed of singlet scalar DM interacting with the Standard Model (SM) through Higgs portal coupling. We compute relic density and direct search constraints including the updated LUX bound for two component scenario with non-zero interactions between two DM components in Z{sub 2} × Z{sub 2}{sup '} framework in comparison with the one having O(2) symmetry. We point out availability of a significantly large region of parameter space of such a multipartite model with DM-DM interactions.

Optimal updating magnitude in adaptive flat-distribution sampling

NASA Astrophysics Data System (ADS)

Zhang, Cheng; Drake, Justin A.; Ma, Jianpeng; Pettitt, B. Montgomery

2017-11-01

We present a study on the optimization of the updating magnitude for a class of free energy methods based on flat-distribution sampling, including the Wang-Landau (WL) algorithm and metadynamics. These methods rely on adaptive construction of a bias potential that offsets the potential of mean force by histogram-based updates. The convergence of the bias potential can be improved by decreasing the updating magnitude with an optimal schedule. We show that while the asymptotically optimal schedule for the single-bin updating scheme (commonly used in the WL algorithm) is given by the known inverse-time formula, that for the Gaussian updating scheme (commonly used in metadynamics) is often more complex. We further show that the single-bin updating scheme is optimal for very long simulations, and it can be generalized to a class of bandpass updating schemes that are similarly optimal. These bandpass updating schemes target only a few long-range distribution modes and their optimal schedule is also given by the inverse-time formula. Constructed from orthogonal polynomials, the bandpass updating schemes generalize the WL and Langfeld-Lucini-Rago algorithms as an automatic parameter tuning scheme for umbrella sampling.

Optimal updating magnitude in adaptive flat-distribution sampling.

PubMed

Zhang, Cheng; Drake, Justin A; Ma, Jianpeng; Pettitt, B Montgomery

2017-11-07

We present a study on the optimization of the updating magnitude for a class of free energy methods based on flat-distribution sampling, including the Wang-Landau (WL) algorithm and metadynamics. These methods rely on adaptive construction of a bias potential that offsets the potential of mean force by histogram-based updates. The convergence of the bias potential can be improved by decreasing the updating magnitude with an optimal schedule. We show that while the asymptotically optimal schedule for the single-bin updating scheme (commonly used in the WL algorithm) is given by the known inverse-time formula, that for the Gaussian updating scheme (commonly used in metadynamics) is often more complex. We further show that the single-bin updating scheme is optimal for very long simulations, and it can be generalized to a class of bandpass updating schemes that are similarly optimal. These bandpass updating schemes target only a few long-range distribution modes and their optimal schedule is also given by the inverse-time formula. Constructed from orthogonal polynomials, the bandpass updating schemes generalize the WL and Langfeld-Lucini-Rago algorithms as an automatic parameter tuning scheme for umbrella sampling.

10 CFR 72.70 - Safety analysis report updating.

Code of Federal Regulations, 2011 CFR

2011-01-01

... original FSAR or, as appropriate, the last update to the FSAR under this section. The update shall include... for an ISFSI or MRS shall update periodically, as provided in paragraphs (b) and (c) of this section... applicant commitments developed during the license approval and/or hearing process. (b) Each update shall...

10 CFR 72.70 - Safety analysis report updating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... original FSAR or, as appropriate, the last update to the FSAR under this section. The update shall include... for an ISFSI or MRS shall update periodically, as provided in paragraphs (b) and (c) of this section... applicant commitments developed during the license approval and/or hearing process. (b) Each update shall...

10 CFR 72.70 - Safety analysis report updating.

Code of Federal Regulations, 2013 CFR

2013-01-01

... original FSAR or, as appropriate, the last update to the FSAR under this section. The update shall include... for an ISFSI or MRS shall update periodically, as provided in paragraphs (b) and (c) of this section... applicant commitments developed during the license approval and/or hearing process. (b) Each update shall...

10 CFR 72.70 - Safety analysis report updating.

Code of Federal Regulations, 2012 CFR

2012-01-01

... original FSAR or, as appropriate, the last update to the FSAR under this section. The update shall include... for an ISFSI or MRS shall update periodically, as provided in paragraphs (b) and (c) of this section... applicant commitments developed during the license approval and/or hearing process. (b) Each update shall...

The Updating of Geospatial Base Data

NASA Astrophysics Data System (ADS)

Alrajhi, Muhamad N.; Konecny, Gottfried

2018-04-01

Topopographic mapping issues concern the area coverage at different scales and their age. The age of the map is determined by the system of updating. The United Nations (UNGGIM) have attempted to track the global map coverage at various scale ranges, which has greatly improved in recent decades. However the poor state of updating of base maps is still a global problem. In Saudi Arabia large scale mapping is carried out for all urban, suburban and rural areas by aerial surveys. Updating is carried out by remapping every 5 to 10 years. Due to the rapid urban development this is not satisfactory, but faster update methods are forseen by use of high resolution satellite imagery and the improvement of object oriented geodatabase structures, which will permit to utilize various survey technologies to update the photogrammetry established geodatabases. The longterm goal is to create an geodata infrastructure, which exists in Great Britain or Germany.

Update on GH therapy in adults.

PubMed

Boguszewski, Cesar Luiz

2017-01-01

Over the last three decades, short- and long-term observational studies, clinical trials, systematic reviews, and meta-analyses have provided relevant information on the efficacy and safety of growth hormone (GH) replacement therapy in adults with GH deficiency (AGHD). The knowledge acquired during this time has been compiled into different guidelines that offer clinicians an evidence-based, practical approach for the management of AGHD. There are, however, still open questions in some key areas in which recommendations are supported by only moderate or weak evidence. In the last recent years, the development of long-acting GH preparations has created new therapeutic possibilities by decreasing injection frequency, improving adherence and thereby potentially maximizing clinical outcomes. The aims of this review are to advance our understanding on the diagnosis and treatment of AGHD and to present an update and future perspectives on the use of long-acting GH preparations.

76 FR 10246 - Updating Fire Safety Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-24

... DEPARTMENT OF VETERANS AFFAIRS 38 CFR Parts 17 and 59 RIN 2900-AN57 Updating Fire Safety Standards... regulations and update the standards for VA approval of such facilities, including standards for fire safety... to ``RIN 2900-AN57--Updating Fire Safety [[Page 10247

40 CFR 68.190 - Updates.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 15 2011-07-01 2011-07-01 false Updates. 68.190 Section 68.190 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CHEMICAL ACCIDENT PREVENTION PROVISIONS Risk Management Plan § 68.190 Updates. (a) The owner or operator shall...

40 CFR 68.190 - Updates.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Updates. 68.190 Section 68.190 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CHEMICAL ACCIDENT PREVENTION PROVISIONS Risk Management Plan § 68.190 Updates. (a) The owner or operator shall...

10 CFR 72.248 - Safety analysis report updating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... appropriate, the last update to the FSAR under this section. The update shall include the effects 1 of: 1... for a spent fuel storage cask design shall update periodically, as provided in paragraph (b) of this... the issued Certificate of Compliance (CoC). (b) Each update shall contain all the changes necessary to...

10 CFR 72.248 - Safety analysis report updating.

Code of Federal Regulations, 2013 CFR

2013-01-01

... appropriate, the last update to the FSAR under this section. The update shall include the effects 1 of: 1... for a spent fuel storage cask design shall update periodically, as provided in paragraph (b) of this... the issued Certificate of Compliance (CoC). (b) Each update shall contain all the changes necessary to...

10 CFR 72.248 - Safety analysis report updating.

Code of Federal Regulations, 2012 CFR

2012-01-01

... appropriate, the last update to the FSAR under this section. The update shall include the effects 1 of: 1... for a spent fuel storage cask design shall update periodically, as provided in paragraph (b) of this... the issued Certificate of Compliance (CoC). (b) Each update shall contain all the changes necessary to...

10 CFR 72.248 - Safety analysis report updating.

Code of Federal Regulations, 2011 CFR

2011-01-01

... appropriate, the last update to the FSAR under this section. The update shall include the effects 1 of: 1... for a spent fuel storage cask design shall update periodically, as provided in paragraph (b) of this... the issued Certificate of Compliance (CoC). (b) Each update shall contain all the changes necessary to...

Email Updates About FASTSim | Transportation Research | NREL

Science.gov Websites

Email Updates About FASTSim Email Updates about FASTSim Subscribe Please provide the following information to subscribe for email updates about FASTSim, the Future Automotive Systems Technology Simulator . * indicates required Email Address: * Name (first and last): Organization/Affiliation: Subscribe

Email Updates about ADOPT | Transportation Research | NREL

Science.gov Websites

Email Updates about ADOPT Email Updates about ADOPT Subscribe Please provide the following information to subscribe for email updates about ADOPT, the Automotive Deployment Options Projection Tool . * indicates required Email Address: * Name (first and last): Organization/Affiliation Subscribe

Human Health Effects of Dichloromethane: Key Findings and Scientific Issues

PubMed Central

Schlosser, Paul M.; Bale, Ambuja S.; Gibbons, Catherine F.; Wilkins, Amina

2014-01-01

Background: The U.S. EPA’s Integrated Risk Information System (IRIS) completed an updated toxicological review of dichloromethane in November 2011. Objectives: In this commentary we summarize key results and issues of this review, including exposure sources, identification of potential health effects, and updated physiologically based pharmacokinetic (PBPK) modeling. Methods: We performed a comprehensive review of primary research studies and evaluation of PBPK models. Discussion: Hepatotoxicity was observed in oral and inhalation exposure studies in several studies in animals; neurological effects were also identified as a potential area of concern. Dichloromethane was classified as likely to be carcinogenic in humans based primarily on evidence of carcinogenicity at two sites (liver and lung) in male and female B6C3F1 mice (inhalation exposure) and at one site (liver) in male B6C3F1 mice (drinking-water exposure). Recent epidemiologic studies of dichloromethane (seven studies of hematopoietic cancers published since 2000) provide additional data raising concerns about associations with non-Hodgkin lymphoma and multiple myeloma. Although there are gaps in the database for dichloromethane genotoxicity (i.e., DNA adduct formation and gene mutations in target tissues in vivo), the positive DNA damage assays correlated with tissue and/or species availability of functional glutathione S-transferase (GST) metabolic activity, the key activation pathway for dichloromethane-induced cancer. Innovations in the IRIS assessment include estimation of cancer risk specifically for a presumed sensitive genotype (GST-theta-1+/+), and PBPK modeling accounting for human physiological distributions based on the expected distribution for all individuals 6 months to 80 years of age. Conclusion: The 2011 IRIS assessment of dichloromethane provides insights into the toxicity of a commonly used solvent. Citation: Schlosser PM, Bale AS, Gibbons CF, Wilkins A, Cooper GS. 2015. Human health

Dynamic updating atlas for heart segmentation with a nonlinear field-based model.

PubMed

Cai, Ken; Yang, Rongqian; Yue, Hongwei; Li, Lihua; Ou, Shanxing; Liu, Feng

2017-09-01

Segmentation of cardiac computed tomography (CT) images is an effective method for assessing the dynamic function of the heart and lungs. In the atlas-based heart segmentation approach, the quality of segmentation usually relies upon atlas images, and the selection of those reference images is a key step. The optimal goal in this selection process is to have the reference images as close to the target image as possible. This study proposes an atlas dynamic update algorithm using a scheme of nonlinear deformation field. The proposed method is based on the features among double-source CT (DSCT) slices. The extraction of these features will form a base to construct an average model and the created reference atlas image is updated during the registration process. A nonlinear field-based model was used to effectively implement a 4D cardiac segmentation. The proposed segmentation framework was validated with 14 4D cardiac CT sequences. The algorithm achieved an acceptable accuracy (1.0-2.8 mm). Our proposed method that combines a nonlinear field-based model and dynamic updating atlas strategies can provide an effective and accurate way for whole heart segmentation. The success of the proposed method largely relies on the effective use of the prior knowledge of the atlas and the similarity explored among the to-be-segmented DSCT sequences. Copyright © 2016 John Wiley & Sons, Ltd.

Systematic reviews of bruising in relation to child abuse-what have we learnt: an overview of review updates.

PubMed

Maguire, Sabine; Mann, Mala

2013-03-07

Dogma has long prevailed regarding the ageing of bruises, and whether certain patterns of bruising are suggestive or diagnostic of child abuse. We conducted the first Systematic Reviews addressing these two issues, to determine the scientific basis for current clinical practice. There have been seven updates since 2004. An all language literature search was performed across 13 databases, 1951-2004, using >60 key words, supplemented by 'snowballing' techniques. Quality standards included a novel confirmation of abuse scale. Updates used expanded key words, and a higher standard for confirmation of abuse. Of 1495 potential studies, only three met the inclusion criteria for ageing of bruises in 2004, confirming that it is inaccurate to do so with the naked eye. This was roundly rejected when first reported, generating a wave of new studies attempting to determine a scientifically valid method to age bruises, none of which are applicable in children yet. Regarding patterns of bruising that may be suggestive or diagnostic of abuse, we included 23 of 167 studies reviewed in 2004, although only 2 were comparative studies. Included studies noted that unintentional bruises occur predominantly on the front of the body, over bony prominences and their presence is directly correlated to the child's level of independent mobility. Bruising patterns in abused children, differed in location (most common site being face, neck, ear, head, trunk, buttocks, arms), and tended to be larger. Updates have included a further 14 studies, including bruising in disabled children, defining distinguishing patterns in severely injured abused and non-abused children, and importance of petechiae. Systematic Reviews of bruising challenged accepted wisdom regarding ageing of bruises, which had no scientific basis; stimulated higher quality research on patterns of bruises distinguishing abusive and non-abusive bruising patterns, and highlighted the benefits of regular updates of these reviews

A 2015 comparison of operational performance : Washington state ferries to ferry operators worldwide.

DOT National Transportation Integrated Search

2015-03-01

This report provides an update to the 2010 report A Comparison of Operational Performance: : Washington State Ferries to Ferry Operators Worldwide, observing changes in Washington State : Ferries, 23 other ferry systems, and the ferry industry ...

Assessing the performance of eight real-time updating models and procedures for the Brosna River

NASA Astrophysics Data System (ADS)

Goswami, M.; O'Connor, K. M.; Bhattarai, K. P.; Shamseldin, A. Y.

2005-10-01

, the simulated outflows of this model only were selected for the subsequent exercise of producing updated discharge forecasts. All the eight forms of updating models for producing lead-time discharge forecasts were found to be capable of producing relatively good lead-1 (1-day ahead) forecasts, with R2 values almost 90% or above. However, for higher lead time forecasts, only three updating models, viz., NARXM, LTF, and NNU, were found to be suitable, with lead-6 values of R2 about 90% or higher. Graphical comparisons were made of the lead-time forecasts for the two largest floods, one in the calibration period and the other in the verification period.

Key articles and guidelines in the management of pulmonary arterial hypertension: 2011 update.

PubMed

Johnson, Samuel G; Kayser, Steven R; Attridge, Rebecca L; Duvall, Laura; Kiser, Tyree H; Moote, Rebecca; Reed, Brent N; Rodgers, Jo E; Erstad, Brian

2012-06-01

teaching tool, reference resource, or update of the literature for pharmacy clinicians, physicians, and students. © 2012 Pharmacotherapy Publications, Inc.

British Military surgical key performance indicators: time for an update?

PubMed

Marsden, Max Er; Sharrock, A E; Hansen, C L; Newton, N J; Bowley, D M; Midwinter, M

2016-10-01

Key performance indicators (KPIs) are metrics that compare actual care against an ideal structure, process or outcome standard. KPIs designed to assess performance in deployed military surgical facilities have previously been published. This study aimed to review the overall performance of surgical trauma care for casualties treated at Role 3 Camp Bastion, Medical Treatment Facility, Afghanistan, in light of the existing Defence Medical Services (DMS) KPIs. The secondary aims were to assess the utility of the surgical KPIs and make recommendations for future surgical trauma care review. Data on 22 surgical parameters were prospectively collected for 150 injured patients who had primary surgery at Camp Bastion between 1 May 2013 and 20 August 2013. Additional information for these patients was obtained using the Joint Theatre Trauma Register. The authors assessed data recording, applicability and compliance with the KPIs. Median data recording was 100% (IQR 98%-100%), median applicability was 56% (IQR 10%-99%) and median compliance was 78% (IQR 58%-93%). One KPI was not applicable to any patient in our population. Eleven KPIs achieved >80% compliance, five KPIs had 80%-60% compliance and five KPIs had <60% compliance. Recommendations are made for minor modifications to the current KPIs. 78% compliance with the DMS KPIs provides a snapshot of the performance of the surgical aspect of military trauma care in 2013. The KPIs highlight areas for improvement in service delivery. Individual KPI development should be driven by evidence and reflect advances in practice and knowledge. A method of stakeholder consultation, and sequential refinement following evidence review, may be the right process to develop the future set of DMS KPIs. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

6. September 1971 DETAIL VIEW OF CHAIN PADLOCK AND KEY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. September 1971 DETAIL VIEW OF CHAIN PADLOCK AND KEY TO SECURE DOOR TO MAIN CELL BLOCK, NOTE STANDARD MODERN PADLOCK FOR SIZE COMPARISON - Jefferson County Jail & Sheriff's Office, Courthouse Square, Madison, Jefferson County, IN

JESD57 Test Standard, Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation Revision Update

NASA Technical Reports Server (NTRS)

Lauenstein, Jean-Marie

2016-01-01

The JEDEC JESD57 test standard, Procedures for the Measurement of Single-Event Effects in Semiconductor Devices from Heavy-Ion Irradiation, is undergoing its first revision since 1996. This presentation will provide an overview of some of the key proposed updates to the document.

49 CFR 360.5 - Updating user fees.

Code of Federal Regulations, 2010 CFR

2010-10-01

... updating the cost components comprising the fee. Cost components shall be updated as follows: (1) Direct... determined by the cost study in Regulations Governing Fees For Service, 1 I.C.C. 2d 60 (1984), or subsequent... by total office costs for the office directly associated with user fee activity. Actual updating of...

Arthrogryposis: an update on clinical aspects, etiology, and treatment strategies

PubMed Central

Feluś, Jarosław

2016-01-01

Arthrogryposes – multiple joint contractures – are a clinically and etiologically heterogeneous class of diseases, where accurate diagnosis, recognition of the underlying pathology and classification are of key importance for the prognosis as well as for selection of appropriate management. This treatment remains challenging and optimally in arthrogrypotic patients should be carried out by a team of specialists familiar with all aspects of arthrogryposis pathology and treatment modalities: rehabilitation, orthotics and surgery. In this comprehensive review article, based on literature and clinical experience, the authors present an update on current knowledge on etiology, classifications and treatment options for skeletal deformations possible in arthrogryposis. PMID:26925114

Protocol Independent Adaptive Route Update for VANET

PubMed Central

Rasheed, Asim; Qayyum, Amir

2014-01-01

High relative node velocity and high active node density have presented challenges to existing routing approaches within highly scaled ad hoc wireless networks, such as Vehicular Ad hoc Networks (VANET). Efficient routing requires finding optimum route with minimum delay, updating it on availability of a better one, and repairing it on link breakages. Current routing protocols are generally focused on finding and maintaining an efficient route, with very less emphasis on route update. Adaptive route update usually becomes impractical for dense networks due to large routing overheads. This paper presents an adaptive route update approach which can provide solution for any baseline routing protocol. The proposed adaptation eliminates the classification of reactive and proactive by categorizing them as logical conditions to find and update the route. PMID:24723807

Validation of updated neutronic calculation models proposed for Atucha-II PHWR. Part I: Benchmark comparisons of WIMS-D5 and DRAGON cell and control rod parameters with MCNP5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mollerach, R.; Leszczynski, F.; Fink, J.

2006-07-01

In 2005 the Argentine Government took the decision to complete the construction of the Atucha-II nuclear power plant, which has been progressing slowly during the last ten years. Atucha-II is a 745 MWe nuclear station moderated and cooled with heavy water, of German (Siemens) design located in Argentina. It has a pressure-vessel design with 451 vertical coolant channels, and the fuel assemblies (FA) are clusters of 37 natural UO{sub 2} rods with an active length of 530 cm. For the reactor physics area, a revision and update calculation methods and models (cell, supercell and reactor) was recently carried out coveringmore » cell, supercell (control rod) and core calculations. As a validation of the new models some benchmark comparisons were done with Monte Carlo calculations with MCNP5. This paper presents comparisons of cell and supercell benchmark problems based on a slightly idealized model of the Atucha-I core obtained with the WIMS-D5 and DRAGON codes with MCNP5 results. The Atucha-I core was selected because it is smaller, similar from a neutronic point of view, and more symmetric than Atucha-II Cell parameters compared include cell k-infinity, relative power levels of the different rings of fuel rods, and some two-group macroscopic cross sections. Supercell comparisons include supercell k-infinity changes due to the control rods (tubes) of steel and hafnium. (authors)« less

An update on X-ray reflection gratings developed for future missions

NASA Astrophysics Data System (ADS)

Miles, Drew

2018-01-01

X-ray reflection gratings are a key technology being studied for future X-ray spectroscopy missions, including the Lynx X-ray mission under consideration for the 2020 Decadal Survey. We present an update on the status of X-ray reflection gratings being developed at Penn State University, including current fabrication techniques and mass-replication processes and the latest diffraction efficiency results and resolving power measurements. Individual off-plane X-ray reflection gratings have exceeded the current Lynx requirements for both effective area and resolving power. Finally, we discuss internal projects that will advance the technology readiness level of these gratings.

Subsonic Longitudinal Performance Coefficient Extraction from Shuttle Flight Data: an Accuracy Assessment for Determination of Data Base Updates

NASA Technical Reports Server (NTRS)

Findlay, J. T.; Kelly, G. M.; Mcconnell, J. G.; Compton, H. R.

1983-01-01

Longitudinal performance comparisons between flight derived and predicted values are presented for the first five NASA Space Shuttle Columbia flights. Though subsonic comparisons are emphasized, comparisons during the transonic and low supersonic regions of flight are included. Computed air data information based on the remotely sensed atmospheric measurements as well as in situ Orbiter Air Data System (ADS) measurements were incorporated. Each air data source provides for comparisons versus the predicted values from the LaRC data base. Principally, L/D, C sub L, and C sub D, comparisons are presented, though some pitching moment results are included. Similarities in flight conditions and spacecraft configuration during the first five flights are discussed. Contributions from the various elements of the data base are presented and the overall differences observed between the flight and predicted values are discussed in terms of expected variations. A discussion on potential data base updates is presented based on the results from the five flights to date.

Human health effects of dichloromethane: key findings and scientific issues.

PubMed

Schlosser, Paul M; Bale, Ambuja S; Gibbons, Catherine F; Wilkins, Amina; Cooper, Glinda S

2015-02-01

The U.S. EPA's Integrated Risk Information System (IRIS) completed an updated toxicological review of dichloromethane in November 2011. In this commentary we summarize key results and issues of this review, including exposure sources, identification of potential health effects, and updated physiologically based pharmacokinetic (PBPK) modeling. We performed a comprehensive review of primary research studies and evaluation of PBPK models. Hepatotoxicity was observed in oral and inhalation exposure studies in several studies in animals; neurological effects were also identified as a potential area of concern. Dichloromethane was classified as likely to be carcinogenic in humans based primarily on evidence of carcinogenicity at two sites (liver and lung) in male and female B6C3F1 mice (inhalation exposure) and at one site (liver) in male B6C3F1 mice (drinking-water exposure). Recent epidemiologic studies of dichloromethane (seven studies of hematopoietic cancers published since 2000) provide additional data raising concerns about associations with non-Hodgkin lymphoma and multiple myeloma. Although there are gaps in the database for dichloromethane genotoxicity (i.e., DNA adduct formation and gene mutations in target tissues in vivo), the positive DNA damage assays correlated with tissue and/or species availability of functional glutathione S-transferase (GST) metabolic activity, the key activation pathway for dichloromethane-induced cancer. Innovations in the IRIS assessment include estimation of cancer risk specifically for a presumed sensitive genotype (GST-theta-1+/+), and PBPK modeling accounting for human physiological distributions based on the expected distribution for all individuals 6 months to 80 years of age. The 2011 IRIS assessment of dichloromethane provides insights into the toxicity of a commonly used solvent.

Design and update of a classification system: the UCSD map of science.

PubMed

Börner, Katy; Klavans, Richard; Patek, Michael; Zoss, Angela M; Biberstine, Joseph R; Light, Robert P; Larivière, Vincent; Boyack, Kevin W

2012-01-01

Global maps of science can be used as a reference system to chart career trajectories, the location of emerging research frontiers, or the expertise profiles of institutes or nations. This paper details data preparation, analysis, and layout performed when designing and subsequently updating the UCSD map of science and classification system. The original classification and map use 7.2 million papers and their references from Elsevier's Scopus (about 15,000 source titles, 2001-2005) and Thomson Reuters' Web of Science (WoS) Science, Social Science, Arts & Humanities Citation Indexes (about 9,000 source titles, 2001-2004)-about 16,000 unique source titles. The updated map and classification adds six years (2005-2010) of WoS data and three years (2006-2008) from Scopus to the existing category structure-increasing the number of source titles to about 25,000. To our knowledge, this is the first time that a widely used map of science was updated. A comparison of the original 5-year and the new 10-year maps and classification system show (i) an increase in the total number of journals that can be mapped by 9,409 journals (social sciences had a 80% increase, humanities a 119% increase, medical (32%) and natural science (74%)), (ii) a simplification of the map by assigning all but five highly interdisciplinary journals to exactly one discipline, (iii) a more even distribution of journals over the 554 subdisciplines and 13 disciplines when calculating the coefficient of variation, and (iv) a better reflection of journal clusters when compared with paper-level citation data. When evaluating the map with a listing of desirable features for maps of science, the updated map is shown to have higher mapping accuracy, easier understandability as fewer journals are multiply classified, and higher usability for the generation of data overlays, among others.

Design and Update of a Classification System: The UCSD Map of Science

PubMed Central

Börner, Katy; Klavans, Richard; Patek, Michael; Zoss, Angela M.; Biberstine, Joseph R.; Light, Robert P.; Larivière, Vincent; Boyack, Kevin W.

2012-01-01

Global maps of science can be used as a reference system to chart career trajectories, the location of emerging research frontiers, or the expertise profiles of institutes or nations. This paper details data preparation, analysis, and layout performed when designing and subsequently updating the UCSD map of science and classification system. The original classification and map use 7.2 million papers and their references from Elsevier’s Scopus (about 15,000 source titles, 2001–2005) and Thomson Reuters’ Web of Science (WoS) Science, Social Science, Arts & Humanities Citation Indexes (about 9,000 source titles, 2001–2004)–about 16,000 unique source titles. The updated map and classification adds six years (2005–2010) of WoS data and three years (2006–2008) from Scopus to the existing category structure–increasing the number of source titles to about 25,000. To our knowledge, this is the first time that a widely used map of science was updated. A comparison of the original 5-year and the new 10-year maps and classification system show (i) an increase in the total number of journals that can be mapped by 9,409 journals (social sciences had a 80% increase, humanities a 119% increase, medical (32%) and natural science (74%)), (ii) a simplification of the map by assigning all but five highly interdisciplinary journals to exactly one discipline, (iii) a more even distribution of journals over the 554 subdisciplines and 13 disciplines when calculating the coefficient of variation, and (iv) a better reflection of journal clusters when compared with paper-level citation data. When evaluating the map with a listing of desirable features for maps of science, the updated map is shown to have higher mapping accuracy, easier understandability as fewer journals are multiply classified, and higher usability for the generation of data overlays, among others. PMID:22808037

Updates Technologies of Media Change

ERIC Educational Resources Information Center

Comer, Joshua

2015-01-01

Whether as status notifications in news feeds or interactive prompts in online video services, updates punctuate the background routines of media by bringing a variety of changes to the attention of users. In this dissertation I argue that updates rationalize media change by making previously obscure actions of users and movements of technologies…

Defining the system of care concept and philosophy: to update or not to update?

PubMed

Stroul, Beth A; Blau, Gary M

2010-02-01

This commentary considers the task of updating the system of care concept and philosophy within its historical context, reviewing the original intent of the definition and clarifying misconceptions about its meaning. The authors identify the aspects of the concept and philosophy that should be updated based on the latest thinking, experience, and data, such as incorporating applicability to a broader range of populations, increasing the emphasis on the core values, specifying desired outcomes, and adding accountability as a critical element. An updated definition and values and principles are proposed, and the importance of always presenting the definition along with the accompanying specification of the philosophy is emphasized in order to increase its utility in assisting the field to move from theory to practice.

Key comparison BIPM.RI(I)-K6 of the standards for absorbed dose to water of the VSL, Netherlands and the BIPM in accelerator photon beams

NASA Astrophysics Data System (ADS)

Picard, S.; Burns, D. T.; Roger, P.; de Prez, L. A.; Jansen, B. J.; Pooter, J. A.

2017-01-01

A comparison of the dosimetry for accelerator photon beams was carried out between the Dutch Metrology Institute (VSL) and the Bureau International des Poids et Mesures (BIPM) from 23 September to 20 October 2014. The comparison was based on the determination of absorbed dose to water for three radiation qualities of the medical accelerator facilities of the National Physical Laboratory (United Kingdom). After establishing Draft B, the VSL discovered an error in the calculation of the correction factor for excess-heat linked to the VSL glass vessel used in the measurements at the NPL. The comparison results for the revised standard, reported as ratios of the VSL and the BIPM evaluations (and with the combined standard uncertainties given in parentheses), are 0.9959 (54) at 6 MV, 0.9958 (64) at 10 MV and 0.9991 (75) at 25 MV. This result is part of the on-going BIPM.RI(I)-K6 series of comparisons. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCRI, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

NASA Update

NASA Image and Video Library

2010-04-08

"NASA Update" program with NASA Administrator Charles Bolden, NASA Deputy Administrator Lori Garver and NASA Acting Asistant Administrator for Public Affairs Bob Jacobs as moderator, NASA Headquarters, Thursday, April 8, 2010 in Washington. Photo Credit: (NASA/Bill Ingalls)

Estimating the size of key populations at higher risk of HIV infection: a summary of experiences and lessons presented during a technical meeting on size estimation among key populations in Asian countries

PubMed Central

Calleja, Jesus Maria Garcia; Zhao, Jinkou; Reddy, Amala; Seguy, Nicole

2014-01-01

Problem Size estimates of key populations at higher risk of HIV exposure are recognized as critical for understanding the trajectory of the HIV epidemic and planning and monitoring an effective response, especially for countries with concentrated and low epidemics such as those in Asia. Context To help countries estimate population sizes of key populations, global guidelines were updated in 2011 to reflect new technical developments and recent field experiences in applying these methods. Action In September 2013, a meeting of programme managers and experts experienced with population size estimates (PSE) for key populations was held for 13 Asian countries. This article summarizes the key results presented, shares practical lessons learnt and reviews the methodological approaches from implementing PSE in 13 countries. Lessons learnt It is important to build capacity to collect, analyse and use PSE data; establish a technical review group; and implement a transparent, well documented process. Countries should adapt global PSE guidelines and maintain operational definitions that are more relevant and useable for country programmes. Development of methods for non-venue-based key populations requires more investment and collaborative efforts between countries and among partners. PMID:25320676

Email Updates

MedlinePlus

... MedlinePlus GO GO About MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español ... spam" or "junk." About MedlinePlus Site Map FAQs Customer Support Get email updates Subscribe to RSS Follow ...

Breast Cancer and Estrogen-Alone Update

MedlinePlus

... Current Issue Past Issues Research News From NIH Breast Cancer and Estrogen-Alone Update Past Issues / Summer 2006 ... hormone therapy does not increase the risk of breast cancer in postmenopausal women, according to an updated analysis ...

Working Memory Updating as a Predictor of Academic Attainment

ERIC Educational Resources Information Center

Lechuga, M. Teresa; Pelegrina, Santiago; Pelaez, Jose L.; Martin-Puga, M. Eva; Justicia, M. Jose

2016-01-01

There is growing evidence supporting the importance of executive functions, and specifically working memory updating (WMU), for children's academic achievement. This study aimed to assess the specific contribution of updating to the prediction of academic performance. Two updating tasks, which included different updating components, were…

Program Updates - San Antonio River Basin

EPA Pesticide Factsheets

This page will house updates for this urban waters partnership location. As projects progress, status updates can be posted here to reflect the ongoing work by partners in San Antonio working on the San Antonio River Basin.

The 2014 Nucleic Acids Research Database Issue and an updated NAR online Molecular Biology Database Collection.

PubMed

Fernández-Suárez, Xosé M; Rigden, Daniel J; Galperin, Michael Y

2014-01-01

The 2014 Nucleic Acids Research Database Issue includes descriptions of 58 new molecular biology databases and recent updates to 123 databases previously featured in NAR or other journals. For convenience, the issue is now divided into eight sections that reflect major subject categories. Among the highlights of this issue are six databases of the transcription factor binding sites in various organisms and updates on such popular databases as CAZy, Database of Genomic Variants (DGV), dbGaP, DrugBank, KEGG, miRBase, Pfam, Reactome, SEED, TCDB and UniProt. There is a strong block of structural databases, which includes, among others, the new RNA Bricks database, updates on PDBe, PDBsum, ArchDB, Gene3D, ModBase, Nucleic Acid Database and the recently revived iPfam database. An update on the NCBI's MMDB describes VAST+, an improved tool for protein structure comparison. Two articles highlight the development of the Structural Classification of Proteins (SCOP) database: one describes SCOPe, which automates assignment of new structures to the existing SCOP hierarchy; the other one describes the first version of SCOP2, with its more flexible approach to classifying protein structures. This issue also includes a collection of articles on bacterial taxonomy and metagenomics, which includes updates on the List of Prokaryotic Names with Standing in Nomenclature (LPSN), Ribosomal Database Project (RDP), the Silva/LTP project and several new metagenomics resources. The NAR online Molecular Biology Database Collection, http://www.oxfordjournals.org/nar/database/c/, has been expanded to 1552 databases. The entire Database Issue is freely available online on the Nucleic Acids Research website (http://nar.oxfordjournals.org/).

The neural systems for perceptual updating.

PubMed

Stöttinger, Elisabeth; Aichhorn, Markus; Anderson, Britt; Danckert, James

2018-04-01

In a constantly changing environment we must adapt to both abrupt and gradual changes to incoming information. Previously, we demonstrated that a distributed network (including the anterior insula and anterior cingulate cortex) was active when participants updated their initial representations (e.g., it's a cat) in a gradually morphing picture task (e.g., now it's a rabbit; Stöttinger et al., 2015). To shed light on whether these activations reflect the proactive decisions to update or perceptual uncertainty, we introduced two additional conditions. By presenting picture morphs twice we controlled for uncertainty in perceptual decision making. Inducing an abrupt shift in a third condition allowed us to differentiate between a proactive decision in uncertainty-driven updating and a reactive decision in surprise-based updating. We replicated our earlier result, showing the robustness of the effect. In addition, we found activation in the anterior insula (bilaterally) and the mid frontal area/ACC in all three conditions, indicative of the importance of these areas in updating of all kinds. When participants were naïve as to the identity of the second object, we found higher activations in the mid-cingulate cortex and cuneus - areas typically associated with task difficulty, in addition to higher activations in the right TPJ most likely reflecting the shift to a new perspective. Activations associated with the proactive decision to update to a new interpretation were found in a network including the dorsal ACC known to be involved in exploration and the endogenous decision to switch to a new interpretation. These findings suggest a general network commonly engaged in all types of perceptual decision making supported by additional networks associated with perceptual uncertainty or updating provoked by either proactive or reactive decision making. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Indoor Spatial Updating With Impaired Vision

PubMed Central

Legge, Gordon E.; Granquist, Christina; Baek, Yihwa; Gage, Rachel

2016-01-01

Purpose Spatial updating is the ability to keep track of position and orientation while moving through an environment. We asked how normally sighted and visually impaired subjects compare in spatial updating and in estimating room dimensions. Methods Groups of 32 normally sighted, 16 low-vision, and 16 blind subjects estimated the dimensions of six rectangular rooms. Updating was assessed by guiding the subjects along three-segment paths in the rooms. At the end of each path, they estimated the distance and direction to the starting location, and to a designated target. Spatial updating was tested in five conditions ranging from free viewing to full auditory and visual deprivation. Results The normally sighted and low-vision groups did not differ in their accuracy for judging room dimensions. Correlations between estimated size and physical size were high. Accuracy of low-vision performance was not correlated with acuity, contrast sensitivity, or field status. Accuracy was lower for the blind subjects. The three groups were very similar in spatial-updating performance, and exhibited only weak dependence on the nature of the viewing conditions. Conclusions People with a wide range of low-vision conditions are able to judge room dimensions as accurately as people with normal vision. Blind subjects have difficulty in judging the dimensions of quiet rooms, but some information is available from echolocation. Vision status has little impact on performance in simple spatial updating; proprioceptive and vestibular cues are sufficient. PMID:27978556

Indoor Spatial Updating With Impaired Vision.

PubMed

Legge, Gordon E; Granquist, Christina; Baek, Yihwa; Gage, Rachel

2016-12-01

Spatial updating is the ability to keep track of position and orientation while moving through an environment. We asked how normally sighted and visually impaired subjects compare in spatial updating and in estimating room dimensions. Groups of 32 normally sighted, 16 low-vision, and 16 blind subjects estimated the dimensions of six rectangular rooms. Updating was assessed by guiding the subjects along three-segment paths in the rooms. At the end of each path, they estimated the distance and direction to the starting location, and to a designated target. Spatial updating was tested in five conditions ranging from free viewing to full auditory and visual deprivation. The normally sighted and low-vision groups did not differ in their accuracy for judging room dimensions. Correlations between estimated size and physical size were high. Accuracy of low-vision performance was not correlated with acuity, contrast sensitivity, or field status. Accuracy was lower for the blind subjects. The three groups were very similar in spatial-updating performance, and exhibited only weak dependence on the nature of the viewing conditions. People with a wide range of low-vision conditions are able to judge room dimensions as accurately as people with normal vision. Blind subjects have difficulty in judging the dimensions of quiet rooms, but some information is available from echolocation. Vision status has little impact on performance in simple spatial updating; proprioceptive and vestibular cues are sufficient.

Final report of the key comparison CCQM-K98: Pb isotope amount ratios in bronze

NASA Astrophysics Data System (ADS)

Vogl, Jochen; Yim, Yong-Hyeon; Lee, Kyoung-Seok; Goenaga-Infante, Heidi; Malinowskiy, Dmitriy; Ren, Tongxiang; Wang, Jun; Vocke, Robert D., Jr.; Murphy, Karen; Nonose, Naoko; Rienitz, Olaf; Noordmann, Janine; Näykki, Teemu; Sara-Aho, Timo; Ari, Betül; Cankur, Oktay

2014-01-01

Isotope amount ratios are proving useful in an ever increasing array of applications that range from studies unravelling transport processes, to pinpointing the provenance of specific samples as well as trace element quantification by using isotope dilution mass spectrometry (IDMS). These expanding applications encompass fields as diverse as archaeology, food chemistry, forensic science, geochemistry, medicine and metrology. However, to be effective tools, the isotope ratio data must be reliable and traceable to enable the comparability of measurement results. The importance of traceability and comparability in isotope ratio analysis has already been recognized by the Inorganic Analysis Working Group (IAWG) within the CCQM. While the requirements for isotope ratio accuracy and precision in the case of IDMS are generally quite modest, 'absolute' Pb isotope ratio measurements for geochemical applications as well as forensic provenance studies require Pb isotope ratio measurements of the highest quality. To support present and future CMCs on isotope ratio determinations, a key comparison was urgently needed and therefore initiated at the IAWG meeting in Paris in April 2011. The analytical task within such a comparison was decided to be the measurement of Pb isotope amount ratios in water and bronze. Measuring Pb isotope amount ratios in an aqueous Pb solution tested the ability of analysts to correct for any instrumental effects on the measured ratios, while the measurement of Pb isotope amount ratios in a metal matrix sample provided a real world test of the whole chemical and instrumental procedure. A suitable bronze material with a Pb mass fraction between 10 and 100 mg•kg-1 and a high purity solution of Pb with a mass fraction of approximately 100 mg•kg-1 was available at the pilot laboratory (BAM), both offering a natural-like Pb isotopic composition. The mandatory measurands, the isotope amount ratios n(206Pb)/n(204Pb), n(207Pb)/n(204Pb) and n(208Pb)/n(204Pb

SUPPLEMENTARY COMPARISON: Final report on APMP.PR-S1.1: Bilateral comparison of irradiance responsivity of UVA detectors

NASA Astrophysics Data System (ADS)

Huang, Xuebo

2009-01-01

In order to assess the performance of the standards and techniques used for calibration and measurement of UVA irradiance responsivity of photodetectors in NMISA, South Africa, a new comparison was decided as a follow-up to comparison APMP.PR-S1. It is registered in the Key Comparison Data Base (KCDB) of BIPM as a bilateral supplementary comparison, with the identifier APMP.PR-S1.1. The comparison was carried out following the same technical protocol as that of supplementary comparison APMP PR-S1. The principle, organization and method of the comparison, as well as the preliminary measurements at the pilot laboratory NMC-A*STAR Singapore, were described in the Final Report of the APMP.PR-S1 comparison. The results of this bilateral comparison show that the NMISA's results lie within ±2% against the comparison reference values of APMP.PR-S1, which is a great improvement. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the APMP, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Off-Highway Gasoline Consuption Estimation Models Used in the Federal Highway Administration Attribution Process: 2008 Updates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hwang, Ho-Ling; Davis, Stacy Cagle

2009-12-01

that is possible on the overall totals, to the current FHWA estimates. Because NONROAD2005 model was designed for emission estimation purposes (i.e., not for measuring fuel consumption), it covers different equipment populations from those the FHWA models were based on. Thus, a direct comparison generally was not possible in most sectors. As a result, NONROAD2005 data were not used in the 2008 update of the FHWA off-highway models. The quality of fuel use estimates directly affect the data quality in many tables published in the Highway Statistics. Although updates have been made to the Off-Highway Gasoline Use Model and the Public Use Gasoline Model, some challenges remain due to aging model equations and discontinuation of data sources.« less

Evaluation of the MyWellness Key accelerometer.

PubMed

Herrmann, S D; Hart, T L; Lee, C D; Ainsworth, B E

2011-02-01

to examine the concurrent validity of the Technogym MyWellness Key accelerometer against objective and subjective physical activity (PA) measures. randomised, cross-sectional design with two phases. The laboratory phase compared the MyWellness Key with the ActiGraph GT1M and the Yamax SW200 Digiwalker pedometer during graded treadmill walking, increasing speed each minute. The free-living phase compared the MyWellness Key with the ActiGraph, Digiwalker, Bouchard Activity cord (BAR) and Global Physical Activity Questionnaire (GPAQ) for seven continuous days. Data were analysed using Spearman rank-order correlation coefficients for all comparisons. laboratory and free-living phases. sixteen participants randomly stratified from 41 eligible respondents by sex (n=8 men; n=8 women) and PA levels (n=4 low, n=8 middle and n=4 high active). there was a strong association between the MyWellness Key and the ActiGraph accelerometer during controlled graded treadmill walking (r=0.91, p<0.01) and in free-living settings (r=0.73-0.76 for light to vigorous PA, respectively, p<0.01). No associations were observed between the MyWellness Key and the BAR and GPAQ (p>0.05). the MyWellness Key has a high concurrent validity with the ActiGraph accelerometer to detect PA in both controlled laboratory and free-living settings.

Particle Filtering Methods for Incorporating Intelligence Updates

DTIC Science & Technology

2017-03-01

methodology for incorporating intelligence updates into a stochastic model for target tracking. Due to the non -parametric assumptions of the PF...samples are taken with replacement from the remaining non -zero weighted particles at each iteration. With this methodology , a zero-weighted particle is...incorporation of information updates. A common method for incorporating information updates is Kalman filtering. However, given the probable nonlinear and non

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during KSC Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Updated Guidance for Safe and Effective Use of Contraception.

PubMed

Tepper, Naomi K; Curtis, Kathryn M; Jatlaoui, Tara C; Whiteman, Maura K

2016-11-01

Progress has been made in efforts to reduce unintended pregnancy; however, unintended pregnancy remains a public health issue in the United States. A key component of reducing unintended pregnancy is to increase correct and consistent use of contraception by reducing barriers to access and use. The CDC has recently updated its guidance for the safe and effective use of contraception. The U.S. Medical Eligibility Criteria for Contraceptive Use (US MEC), 2016, and U.S. Selected Practice Recommendations for Contraceptive Use (US SPR), 2016, are intended for healthcare providers to help patients choose a method that is safe and can be used effectively. The recommendations aim to reduce certain barriers to contraception and thus help women, men, and couples to control timing of pregnancies.

MedlinePlus FAQ: How Often MedlinePlus is Updated

MedlinePlus

... System Pharmacists is updated monthly. Natural Medicines Comprehensive Database Consumer Version is updated quarterly. Medical Encyclopedia: Updated monthly. ... Guidelines Viewers & Players MedlinePlus Connect for ...

The Influence of Social Comparison on Visual Representation of One's Face

PubMed Central

Zell, Ethan; Balcetis, Emily

2012-01-01

Can the effects of social comparison extend beyond explicit evaluation to visual self-representation—a perceptual stimulus that is objectively verifiable, unambiguous, and frequently updated? We morphed images of participants' faces with attractive and unattractive references. With access to a mirror, participants selected the morphed image they perceived as depicting their face. Participants who engaged in upward comparison with relevant attractive targets selected a less attractive morph compared to participants exposed to control images (Study 1). After downward comparison with relevant unattractive targets compared to control images, participants selected a more attractive morph (Study 2). Biased representations were not the products of cognitive accessibility of beauty constructs; comparisons did not influence representations of strangers' faces (Study 3). We discuss implications for vision, social comparison, and body image. PMID:22662124

The Geysers-Clear Lake geothermal area, California - an updated geophysical perspective of heat sources

USGS Publications Warehouse

Stanley, W.D.; Blakely, R.J.

1995-01-01

The Geysers-Clear Lake geothermal area encompasses a large dry-steam production area in The Geysers field and a documented high-temperature, high-pressure, water-dominated system in the area largely south of Clear Lake, which has not been developed. An updated view is presented of the geological/geophysical complexities of the crust in this region in order to address key unanswered questions about the heat source and tectonics. Forward modeling, multidimensional inversions, and ideal body analysis of the gravity data, new electromagnetic sounding models, and arguments made from other geophysical data sets suggest that many of the geophysical anomalies have significant contributions from rock property and physical state variations in the upper 7 km and not from "magma' at greater depths. Regional tectonic and magmatic processes are analyzed to develop an updated scenario for pluton emplacement that differs substantially from earlier interpretations. In addition, a rationale is outlined for future exploration for geothermal resources in The Geysers-Clear Lake area. -from Authors

Social Comparison Processes in Organizations

ERIC Educational Resources Information Center

Greenberg, Jerald; Ashton-James, Claire E.; Ashkanasy, Neal M.

2007-01-01

We systematically analyze the role of social comparison processes in organizations. Specifically, we describe how social comparison processes have been used to explain six key areas of organizational inquiry: (1) organizational justice, (2) performance appraisal, (3) virtual work environments, (4) affective behavior in the workplace, (5) stress,…

77 FR 10650 - Annual Update of Filing Fees

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-23

... updating is to adjust the fees on the basis of the Commission's costs for Fiscal Year 2011. DATES... establishing updated fees on the basis of the Commission's Fiscal Year 2011 costs. The adjusted fees announced...] Annual Update of Filing Fees AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Final rule...

78 FR 2880 - Annual Update of Filing Fees

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-15

... updating is to adjust the fees on the basis of the Commission's costs for Fiscal Year 2012. DATES... establishing updated fees on the basis of the Commission's Fiscal Year 2012 costs. The adjusted fees announced...] Annual Update of Filing Fees AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Final rule...

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. Rob Mueller, senior technologist, talks with attendees at the Swamp Works display. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. Rob Mueller, a senior technologist, talks to an attendee about Kennedy’s Swamp Works Laboratory. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

10 CFR 26.57 - Authorization update.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Authorization update. 26.57 Section 26.57 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Granting and Maintaining Authorization § 26.57 Authorization update. (a) Before granting authorization to an individual whose authorization has been interrupted for...

10 CFR 26.57 - Authorization update.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Authorization update. 26.57 Section 26.57 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Granting and Maintaining Authorization § 26.57 Authorization update. (a) Before granting authorization to an individual whose authorization has been interrupted for...

10 CFR 26.57 - Authorization update.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Authorization update. 26.57 Section 26.57 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Granting and Maintaining Authorization § 26.57 Authorization update. (a) Before granting authorization to an individual whose authorization has been interrupted for...

10 CFR 26.57 - Authorization update.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Authorization update. 26.57 Section 26.57 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Granting and Maintaining Authorization § 26.57 Authorization update. (a) Before granting authorization to an individual whose authorization has been interrupted for...

10 CFR 26.57 - Authorization update.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Authorization update. 26.57 Section 26.57 Energy NUCLEAR REGULATORY COMMISSION FITNESS FOR DUTY PROGRAMS Granting and Maintaining Authorization § 26.57 Authorization update. (a) Before granting authorization to an individual whose authorization has been interrupted for...

Woodstove emission measurement methods: Comparison and emission factors update

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCrillis, R.C.; Jaasma, D.R.

1993-01-01

Since woodstoves are tested for certification in the laboratory using EPA Methods 5G and 5H, it is of interest to determine the correlation between these regulatory methods and the inhouse equipment. Two inhouse sampling systems have been used mostwidely: one is an intermittent, pump-driven particulate sampler that collects particulate and condensible organics on a filter and organic adsorbent resin; and the other uses an evacuated cylinder as the motive force and particulate and condensible organics are collected in a condenser and dual filter. Both samplers can operate unattended for 1-week periods. A large number of tests have been run comparingmore » Methods 5G and 5H to both samplers. The paper presents these comparison data and determines the relationships between regulations and field samplers.« less

Comparison of the Carba NP, Modified Carba NP, and Updated Rosco Neo-Rapid Carb Kit Tests for Carbapenemase Detection

PubMed Central

AbdelGhani, Sameh; Thomson, Gina K.; Snyder, James W.

2015-01-01

The accurate detection of carbapenemase-producing organisms is a major challenge for clinical laboratories. The Carba NP test is highly accurate but inconvenient, as it requires frequent preparation of fresh imipenem solution. The current study was designed to compare the Carba NP test to two alternative tests for accuracy and convenience. These were a modified Carba NP test that utilized intravenous (i.v.) imipenem-cilastatin, which is less expensive than reference standard imipenem powder, and an updated version of the Rosco Neo-Rapid Carb kit, which does not require the preparation of imipenem solution and has a shelf life of 2 years. The comparison included 87 isolates that produced class A carbapenemases (including KPC-2, -3, -4, -5, -6, and -8, NMC-A, and SME type), 40 isolates that produced metallo-β-lactamases (including NDM-1, GIM-1, SPM-1, IMP-1, -2, -7, -8, -18, and -27, and VIM-1, -2, and -7), 11 isolates that produced OXA-48, and one isolate that produced OXA-181. Negative controls consisted of 50 isolates that produced extended-spectrum β-lactamases (ESBLs), AmpCs (including hyperproducers), K1, other limited-spectrum β-lactamases, and porin and efflux mutants. Each test exhibited 100% specificity and high sensitivity (Carba NP, 100%; Rosco, 99% using modified interpretation guidelines; and modified Carba NP, 96%). A modified approach to interpretation of the Rosco test was necessary to achieve the sensitivity of 99%. If the accuracy of the modified interpretation is confirmed, the Rosco test is an accurate and more convenient alternative to the Carba NP test. PMID:26311862

Current Status of the LOFAR EoR Key Science Project

NASA Astrophysics Data System (ADS)

Koopmans, L. V. E.; LOFAR EoR KSP Team

2018-05-01

A short status update on the LOFAR Epoch of Reionization (EoR) Key Science Project (KSP) is given, regarding data acquisition, data processing and analysis, and current power-spectrum limits on the redshifted 21-cm signal of neutral hydrogen at redshifts z = 8 - 10. With caution, we present a preliminary astrophysical analysis of ~60 hr of processed LOFAR data and their resulting power spectrum, showing that potentially already interesting limits on X-ray heating during the Cosmic Dawn can already be gained. This is by no means the final analysis of this sub-set of data, but illustrates the future potential when all nearly 3000 hr of data in hand on two EoR windows will have been processed.

Explosive Infrasonic Events: Sensor Comparison Experiment (SCE)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schnurr, J. M.; Garces, M.; Rodgers, A. J.

SCE (sensor comparison experiment) 1 through 4 consists of a series of four controlled above-ground explosions designed to provide new data for overpressure propagation. Infrasound data were collected by LLNL iPhones and other sensors. Origin times, locations HOB, and yields are not being released at this time and are therefore not included in this report. This preliminary report will be updated as access to additional data changes, or instrument responses are determined.

How Documentalists Update SIMBAD

NASA Astrophysics Data System (ADS)

Buga, M.; Bot, C.; Brouty, M.; Bruneau, C.; Brunet, C.; Cambresy, L.; Eisele, A.; Genova, F.; Lesteven, S.; Loup, C.; Neuville, M.; Oberto, A.; Ochsenbein, F.; Perret, E.; Siebert, A.; Son, E.; Vannier, P.; Vollmer, B.; Vonflie, P.; Wenger, M.; Woelfel, F.

2015-04-01

The Strasbourg astronomical Data Center (CDS) was created in 1972 and has had a major role in astronomy for more than forty years. CDS develops a service called SIMBAD that provides basic data, cross-identifications, bibliography, and measurements for astronomical objects outside the solar system. It brings to the scientific community an added value to content which is updated daily by a team of documentalists working together in close collaboration with astronomers and IT specialists. We explain how the CDS staff updates SIMBAD with object citations in the main astronomical journals, as well as with astronomical data and measurements. We also explain how the identification is made between the objects found in the literature and those already existing in SIMBAD. We show the steps followed by the documentalist team to update the database using different tools developed at CDS, like the sky visualizer Aladin, and the large catalogues and survey database VizieR. As a direct result of this teamwork, SIMBAD integrates almost 10.000 bibliographic references per year. The service receives more than 400.000 queries per day.

Reading--Update: Ideals to Reality; Proceedings of the Annual Conference of the Western College Reading Association (7th, Oakland, April 4-6, 1974).

ERIC Educational Resources Information Center

Kerstiens, Gene, Ed.

The thirty-five papers in this volume were presented on the theme "Reading--Update: Ideals to Reality." The keynote address, delivered by Leland L. Medsker, was entitled "Postsecondary Education in the Decade Ahead." Titles of other papers include "Characteristics of Community College Students,""A Key to Unlock…

Effect of display update interval, update type, and background on perception of aircraft separation on a cockpit display on traffic information

NASA Technical Reports Server (NTRS)

Jago, S.; Baty, D.; Oconnor, S.; Palmer, E.

1981-01-01

The concept of a cockpit display of traffic information (CDTI) includes the integration of air traffic, navigation, and other pertinent information in a single electronic display in the cockpit. Concise display symbology was developed for use in later full-mission simulator evaluations of the CDTI concept. Experimental variables used included the update interval motion of the aircraft, the update type, (that is, whether the two aircraft were updated at the same update interval or not), the background (grid pattern or no background), and encounter type (straight or curved). Only the type of encounter affected performance.

Recent Updates of A Multi-Phase Transport (AMPT) Model

NASA Astrophysics Data System (ADS)

Lin, Zi-Wei

2008-10-01

We will present recent updates to the AMPT model, a Monte Carlo transport model for high energy heavy ion collisions, since its first public release in 2004 and the corresponding detailed descriptions in Phys. Rev. C 72, 064901 (2005). The updates often result from user requests. Some of these updates expand the physics processes or descriptions in the model, while some updates improve the usability of the model such as providing the initial parton distributions or help avoid crashes on some operating systems. We will also explain how the AMPT model is being maintained and updated.

Larva and pupa of Ctesias (s. str.) serra (Fabricius, 1792) with remarks on biology and economic importance, and larval comparison of co-occurring genera (Coleoptera, Dermestidae).

PubMed

Kadej, Marcin

2018-01-01

Updated descriptions of the last larval instar (based on the larvae and exuviae) and first detailed description of the pupa of Ctesias (s. str.) serra (Fabricius, 1792) (Coleoptera: Dermestidae) are presented. Several morphological characters of C. serra larvae are documented: antenna, epipharynx, mandible, maxilla, ligula, labial palpi, spicisetae, hastisetae, terga, frons, foreleg, and condition of the antecostal suture. The paper is fully illustrated and includes some important additions to extend notes for this species available in the references. Summarised data about biology, economic importance, and distribution of C. serra are also provided. The comparison of larval characteristics for some of the genera of Dermestidae co-occurring with Ctesias is presented. A key for identification of these genera is also provided.

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. At left, Susan Fernandez from the Office of Senator Marco Rubio talks with another attendee near the Education display. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. Attendees mingled and visited various displays, including Ground Systems Development and Operations Program and Education Office displays. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. An attendee talks with engineers Jason Hopkins and Lisa Lutz, at the Ground Systems Development and Operations display. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update

NASA Image and Video Library

2014-03-06

CAPE CANAVERAL, Fla. - Community leaders, business executives, educators, and state and local government leaders were updated on NASA Kennedy Space Center programs and accomplishments during Center Director Bob Cabana’s Center Director Update at the Debus Center at the Kennedy Space Center Visitor Complex in Florida. An attendee talks with Scott Thurston, Kennedy deputy of the spacecraft office at the Commercial Crew Program display. Attendees talked with Cabana and other senior Kennedy managers and visited displays featuring updates on Kennedy programs and projects, including International Space Station, Commercial Crew, Ground System Development and Operations, Launch Services, Center Planning and Development, Technology, KSC Swamp Works and NASA Education. The morning concluded with a tour of the new Space Shuttle Atlantis exhibit at the visitor complex. For more information, visit http://www.nasa.gov/kennedy. Photo credit: NASA/Daniel Casper

Kennedy Space Center Director Update