Potential for Non-Contact ACL Injury Between Step-Close-Jump and Hop-Jump Tasks.

PubMed

Wang, Li-I; Gu, Chin-Yi; Chen, Wei-Ling; Chang, Mu-San

2010-01-01

This study aimed to compare the kinematics and kinetics during the landing of hop-jump and step-close-jump movements in order to provide further inferring that the potential risk of ACL injuries. Eleven elite male volleyball players were recruited to perform hop-jump and step-close-jump tasks. Lower extremity kinematics and ground reaction forces during landing in stop-jump tasks were recorded. Lower extremity kinetics was calculated by using an inverse dynamic process. Step-close-jump tasks demonstrated smaller peak proximal tibia anterior shear forces during the landing phase. In step-close-jump tasks, increasing hip joint angular velocity during initial foot-ground contact decreased peak posterior ground reaction force during the landing phase, which theoretically could reduce the risk of ACL injury. Key pointsThe different landing techniques required for these two stop-jump tasks do not necessarily affect the jump height.Hop-jump decreased the hip joint angular velocity at initial foot contact with ground, which could lead to an increasing peak posterior GRF during the landing phase.Hop-jump decreased hip and knee joint angular flexion displacement during the landing, which could increase the peak vertical loading rate during the landing phase.

A rheological model for elastohydrodynamic contacts based on primary laboratory data

NASA Technical Reports Server (NTRS)

Bair, S.; Winer, W. O.

1979-01-01

A shear rheological model based on primary laboratory data is proposed for concentrated contact lubrication. The model is a Maxwell model modified with a limiting shear stress. Three material properties are required: Low shear stress viscosity, limiting elastic shear modulus, and the limiting shear stress the material can withstand. All three are functions of temperature and pressure. In applying the model to EHD contacts the predicted response possesses the characteristics expected from several experiments reported in the literature and, in one specific case where direct comparison could be made, good numerical agreement is shown.

Indexing and retrieving motions of characters in close contact.

PubMed

Ho, Edmond S L; Komura, Taku

2009-01-01

Human motion indexing and retrieval are important for animators due to the need to search for motions in the database which can be blended and concatenated. Most of the previous researches of human motion indexing and retrieval compute the Euclidean distance of joint angles or joint positions. Such approaches are difficult to apply for cases in which multiple characters are closely interacting with each other, as the relationships of the characters are not encoded in the representation. In this research, we propose a topology-based approach to index the motions of two human characters in close contact. We compute and encode how the two bodies are tangled based on the concept of rational tangles. The encoded relationships, which we define as TangleList, are used to determine the similarity of the pairs of postures. Using our method, we can index and retrieve motions such as one person piggy-backing another, one person assisting another in walking, and two persons dancing / wrestling. Our method is useful to manage a motion database of multiple characters. We can also produce motion graph structures of two characters closely interacting with each other by interpolating and concatenating topologically similar postures and motion clips, which are applicable to 3D computer games and computer animation.

Instrumented Compliant Wrist with Proximity and Contact Sensing for Close Robot Interaction Control.

PubMed

Laferrière, Pascal; Payeur, Pierre

2017-06-14

Compliance has been exploited in various forms in robotic systems to allow rigid mechanisms to come into contact with fragile objects, or with complex shapes that cannot be accurately modeled. Force feedback control has been the classical approach for providing compliance in robotic systems. However, by integrating other forms of instrumentation with compliance into a single device, it is possible to extend close monitoring of nearby objects before and after contact occurs. As a result, safer and smoother robot control can be achieved both while approaching and while touching surfaces. This paper presents the design and extensive experimental evaluation of a versatile, lightweight, and low-cost instrumented compliant wrist mechanism which can be mounted on any rigid robotic manipulator in order to introduce a layer of compliance while providing the controller with extra sensing signals during close interaction with an object's surface. Arrays of embedded range sensors provide real-time measurements on the position and orientation of surfaces, either located in proximity or in contact with the robot's end-effector, which permits close guidance of its operation. Calibration procedures are formulated to overcome inter-sensor variability and achieve the highest available resolution. A versatile solution is created by embedding all signal processing, while wireless transmission connects the device to any industrial robot's controller to support path control. Experimental work demonstrates the device's physical compliance as well as the stability and accuracy of the device outputs. Primary applications of the proposed instrumented compliant wrist include smooth surface following in manufacturing, inspection, and safe human-robot interaction.

Analysis of close-contact melting with inner wall temperature variation in a horizontal cylindrical capsule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saitoh, T.S.; Hoshi, Akira

1997-12-31

Melting and solidification of a phase change material (PCM) in a capsule is of practical importance in latent heat thermal energy storage (LHTES) systems which are considered to be very promising to reduce a peak demand of electricity in the summer season. Two melting modes are involved in melting in capsules. One is close-contact melting between the solid bulk and the capsule wall, and another is natural convection melting in the liquid region. In recent years, close-contact melting processes for a single enclosure have been solved using several numerical methods (e.g., Saitoh and Kato (1994)). However, there is no theoreticalmore » solution considering the inner wall temperature variation within cylindrical or spherical capsules. In this report close-contact melting heat transfer characteristics including melt flow in the liquid film under inner wall temperature distribution were analyzed and simple approximate equations are presented, which facilitates designing of the practical capsule bed LHTES systems. The effects of Stefan number and variable temperature profile etc. were clarified in detail. And the melting velocity of the solid bulk under various conditions was also studied theoretically. In addition, the effects of variable inner wall temperature on molten mass fraction were investigated.« less

Customizing Laboratory Information Systems: Closing the Functionality Gap.

PubMed

Gershkovich, Peter; Sinard, John H

2015-09-01

Highly customizable laboratory information systems help to address great variations in laboratory workflows, typical in Pathology. Often, however, built-in customization tools are not sufficient to add all of the desired functionality and improve systems interoperability. Emerging technologies and advances in medicine often create a void in functionality that we call a functionality gap. These gaps have distinct characteristics—a persuasive need to change the way a pathology group operates, the general availability of technology to address the missing functionality, the absence of this technology from your laboratory information system, and inability of built-in customization tools to address it. We emphasize the pervasive nature of these gaps, the role of pathology informatics in closing them, and suggest methods on how to achieve that. We found that a large number of the papers in the Journal of Pathology Informatics are concerned with these functionality gaps, and an even larger proportion of electronic posters and abstracts presented at the Pathology Informatics Summit conference each year deal directly with these unmet needs in pathology practice. A rapid, continuous, and sustainable approach to closing these gaps is critical for Pathology to provide the highest quality of care, adopt new technologies, and meet regulatory and financial challenges. The key element of successfully addressing functionality gaps is gap ownership—the ability to control the entire pathology information infrastructure with access to complementary systems and components. In addition, software developers with detailed domain expertise, equipped with right tools and methodology can effectively address these needs as they emerge.

Online respondent-driven sampling for studying contact patterns relevant for the spread of close-contact pathogens: a pilot study in Thailand.

PubMed

Stein, Mart L; van Steenbergen, Jim E; Chanyasanha, Charnchudhi; Tipayamongkholgul, Mathuros; Buskens, Vincent; van der Heijden, Peter G M; Sabaiwan, Wasamon; Bengtsson, Linus; Lu, Xin; Thorson, Anna E; Kretzschmar, Mirjam E E

2014-01-01

Information on social interactions is needed to understand the spread of airborne infections through a population. Previous studies mostly collected egocentric information of independent respondents with self-reported information about contacts. Respondent-driven sampling (RDS) is a sampling technique allowing respondents to recruit contacts from their social network. We explored the feasibility of webRDS for studying contact patterns relevant for the spread of respiratory pathogens. We developed a webRDS system for facilitating and tracking recruitment by Facebook and email. One-day diary surveys were conducted by applying webRDS among a convenience sample of Thai students. Students were asked to record numbers of contacts at different settings and self-reported influenza-like-illness symptoms, and to recruit four contacts whom they had met in the previous week. Contacts were asked to do the same to create a network tree of socially connected individuals. Correlations between linked individuals were analysed to investigate assortativity within networks. We reached up to 6 waves of contacts of initial respondents, using only non-material incentives. Forty-four (23.0%) of the initially approached students recruited one or more contacts. In total 257 persons participated, of which 168 (65.4%) were recruited by others. Facebook was the most popular recruitment option (45.1%). Strong assortative mixing was seen by age, gender and education, indicating a tendency of respondents to connect to contacts with similar characteristics. Random mixing was seen by reported number of daily contacts. Despite methodological challenges (e.g. clustering among respondents and their contacts), applying RDS provides new insights in mixing patterns relevant for close-contact infections in real-world networks. Such information increases our knowledge of the transmission of respiratory infections within populations and can be used to improve existing modelling approaches. It is worthwhile

Online Respondent-Driven Sampling for Studying Contact Patterns Relevant for the Spread of Close-Contact Pathogens: A Pilot Study in Thailand

PubMed Central

Stein, Mart L.; van Steenbergen, Jim E.; Chanyasanha, Charnchudhi; Tipayamongkholgul, Mathuros; Buskens, Vincent; van der Heijden, Peter G. M.; Sabaiwan, Wasamon; Bengtsson, Linus; Lu, Xin; Thorson, Anna E.; Kretzschmar, Mirjam E. E.

2014-01-01

Background Information on social interactions is needed to understand the spread of airborne infections through a population. Previous studies mostly collected egocentric information of independent respondents with self-reported information about contacts. Respondent-driven sampling (RDS) is a sampling technique allowing respondents to recruit contacts from their social network. We explored the feasibility of webRDS for studying contact patterns relevant for the spread of respiratory pathogens. Materials and Methods We developed a webRDS system for facilitating and tracking recruitment by Facebook and email. One-day diary surveys were conducted by applying webRDS among a convenience sample of Thai students. Students were asked to record numbers of contacts at different settings and self-reported influenza-like-illness symptoms, and to recruit four contacts whom they had met in the previous week. Contacts were asked to do the same to create a network tree of socially connected individuals. Correlations between linked individuals were analysed to investigate assortativity within networks. Results We reached up to 6 waves of contacts of initial respondents, using only non-material incentives. Forty-four (23.0%) of the initially approached students recruited one or more contacts. In total 257 persons participated, of which 168 (65.4%) were recruited by others. Facebook was the most popular recruitment option (45.1%). Strong assortative mixing was seen by age, gender and education, indicating a tendency of respondents to connect to contacts with similar characteristics. Random mixing was seen by reported number of daily contacts. Conclusions Despite methodological challenges (e.g. clustering among respondents and their contacts), applying RDS provides new insights in mixing patterns relevant for close-contact infections in real-world networks. Such information increases our knowledge of the transmission of respiratory infections within populations and can be used to

Risk factors for latent tuberculosis infection in close contacts of active tuberculosis patients in South Korea: a prospective cohort study.

PubMed

Lee, Seung Jun; Lee, Seung Hun; Kim, You Eun; Cho, Yu Ji; Jeong, Yi Yeong; Kim, Ho Cheol; Lee, Jong Deog; Kim, Jang Rak; Hwang, Young Sil; Kim, Hee Jin; Menzies, Dick

2014-11-18

The diagnosis and treatment of latent tuberculosis infection (LTBI) have become mandatory to reduce the burden of tuberculosis worldwide. Close contacts of active TB patients are at high risk of both active and LTBI. The aim of this study is to identify the predominant risk factors of contracting LTBI, persons in close contact with TB patients were recruited. This study also aimed to compare the efficacy of the tuberculin skin test (TST) and QuantiFERON(®)-TB GOLD (QFT-G) to diagnose LTBI. Close contacts of active pulmonary TB patients visiting a hospital in South Korea were diagnosed for LTBI using TST and/or QFT-G. The association of positive TST and/or QFT-G with the following factors was estimated: age, gender, history of Bacillius Calmette-Guerin (BCG) vaccination, history of pulmonary TB, cohabitation status, the acid-fast bacilli smear status, and presence of cough in source cases. Of 308 subjects, 38.0% (116/305) were TST positive and 28.6% (59/206) were QFT-G positive. TST positivity was significantly associated with male gender (OR: 1.734; 95% CI: 1.001-3.003, p =0.049), history of pulmonary TB (OR: 4.130; 95% CI: 1.441-11.835, p =0.008) and household contact (OR: 2.130; 95% CI: 1.198-3.786, p =0.01) after adjustment for confounding variables. The degree of concordance between TST and QFT-G was fair (70.4%, κ =0.392). A prevalence of LTBI among close contacts of active pulmonary TB patients was high, and prior TB history and being a household contact were risk factors of LTBI in the study population.

Interventions for preventing the spread of infestation in close contacts of people with scabies.

PubMed

FitzGerald, Deirdre; Grainger, Rachel J; Reid, Alex

2014-02-24

Scabies, caused by Sarcoptes scabiei variety hominis or the human itch mite, is a common parasitic infection. While anyone can become infected, it causes significant morbidity in immunocompromised hosts and it spreads easily between human hosts where there is overcrowding or poor sanitation. The most common symptom reported is itch which is worse at night. As the symptoms are attributed to an allergic reaction to the mite, symptoms usually develop between four to six weeks after primary infection. Therefore, people may be infected for some time prior to developing symptoms. During this time, while asymptomatic, they may spread infection to others they are in close contact with. Consequently, it is usually recommended that when an index case is being treated, others who have been in close contact with the index case should also be provided with treatment. To assess the effects of prophylactic interventions for contacts of people with scabies to prevent infestation in the contacts. We searched electronic databases (Cochrane Occupational Safety and Health Review Group Specialised Register, CENTRAL (The Cochrane Library), MEDLINE (Ovid), Pubmed, EMBASE, LILACS, CINAHL, OpenGrey and WHO ICTRP) up to November 2013. Randomised controlled trials (RCTs) or cluster RCTs which compared prophylactic interventions which were given to contacts of index cases with scabies infestation. Interventions could be compared to each other, or to placebo or to no treatment. Both drug treatments and non-drug treatments were acceptable. Two authors intended to extract dichotomous data (developed infection or did not develop infection) for the effects of interventions and report this as risk ratios with 95% confidence intervals. We intended to report any adverse outcomes similarly. We did not include any trials in this review. Out of 29 potentially-relevant studies, we excluded 16 RCTs as the data for the contacts were either not reported or were reported only in combination with the outcomes

The Physical Effects of Contact and Close-Distance Gunfire on Sweatshirt Fleece.

PubMed

Kusluski, Michael A

2018-05-01

Powder stippling caused by the impact of propellant particles during close-distance gunfire has been previously described on skin and solid objects only. Additionally, radial tearing has been described as clear evidence of a contact-distance shot, requiring no further testing. Patterns of discrete perforating holes (referred to here as "stippling perforations") and other physical damage on sweatshirt fleece fabrics were prepared. Using the firearm and ammunition in this study, stippling perforations were observed to a maximum muzzle-to-target distance of 35 cm (10 inches). In addition, radial tearing and disintegration were present (and often more extensive) at greater than contact distance. The presence of stippling perforations could augment muzzle-to-target distance estimates generated using the Griess test, or allow distance estimates when the Griess test is not feasible. Unlike what has been previously reported, testing on the original evidence (or similar substitute) is warranted when physical damage is used to estimate shooting distance. © 2017 American Academy of Forensic Sciences.

Distance of the contact glide in the closing masticatory stroke during mastication of three types of food.

PubMed

Rilo, B; Fernández-Formoso, N; Mora, M J; Cadarso-Suárez, C; Santana, U

2009-08-01

This study was designed to characterize the distance of the contact glide in the closing masticatory stroke in healthy adult subjects, during chewing of three types of food (crustless bread, chewing gum and peanuts). Mandibular movements (masticatory movements and laterality movements with dental contact) were registered using a gnathograph (MK-6I Diagnostic System) on the right and left side during unilateral chewing of the three food types. Length of dental contact was measured in masticatory cycle, which is defined as where the terminal part of the chewing cycles could be superimposed on the pathways taken by the mandible during lateral excursions with occlusal contacts. The length of dental contact during mastication of chewing gum is 1.46 +/- 1 mm, during chewing of soft bread is 1.38 +/- 0.7 mm and during chewing of peanuts is 1.45 +/- 0.9 mm. There is no significant difference in the lengths of dental contact during mastication of three types of foods that enable direct tooth gliding.

Open- and closed-formula laboratory animal diets and their importance to research.

PubMed

Barnard, Dennis E; Lewis, Sherry M; Teter, Beverly B; Thigpen, Julius E

2009-11-01

Almost 40 y ago the scientific community was taking actions to control environmental factors that contribute to variation in the responses of laboratory animals to scientific manipulation. Laboratory animal diet was recognized as an important variable. During the 1970s, the American Institute of Nutrition, National Academy of Science, Institute of Laboratory Animal Resources, and Laboratory Animals Centre Diets Advisory Committee supported the use of 'standard reference diets' in biomedical research as a means to improve the ability to replicate research. As a result the AIN76 purified diet was formulated. During this same time, the laboratory animal nutritionist at the NIH was formulating open-formula, natural-ingredient diets to meet the need for standardized laboratory animal diets. Since the development of open-formula diets, fixed-formula and constant-nutrient-concentration closed-formula laboratory animal natural ingredient diets have been introduced to help reduce the potential variation diet can cause in research.

Open- and Closed-Formula Laboratory Animal Diets and Their Importance to Research

PubMed Central

Barnard, Dennis E; Lewis, Sherry M; Teter, Beverly B; Thigpen, Julius E

2009-01-01

Almost 40 y ago the scientific community was taking actions to control environmental factors that contribute to variation in the responses of laboratory animals to scientific manipulation. Laboratory animal diet was recognized as an important variable. During the 1970s, the American Institute of Nutrition, National Academy of Science, Institute of Laboratory Animal Resources, and Laboratory Animals Centre Diets Advisory Committee supported the use of ‘standard reference diets’ in biomedical research as a means to improve the ability to replicate research. As a result the AIN76 purified diet was formulated. During this same time, the laboratory animal nutritionist at the NIH was formulating open-formula, natural-ingredient diets to meet the need for standardized laboratory animal diets. Since the development of open-formula diets, fixed-formula and constant-nutrient–concentration closed-formula laboratory animal natural ingredient diets have been introduced to help reduce the potential variation diet can cause in research. PMID:19930817

Preference for social contact versus environmental enrichment in male laboratory mice.

PubMed

Van Loo, P L P; Van de Weerd, H A; Van Zutphen, L F M; Baumans, V

2004-04-01

Due to their aggressive nature, male mice are less frequently used than female mice in biomedical research. When aggressive males are being used, individual housing is common practice. The question arises whether this is an acceptable housing for a social species. The present study was designed to gain more insight into the nature of inter-male social contact and into the potential of a form of environmental enrichment (nesting material) to compensate for the lack of social contact. In a series of tests, we analysed whether male mice of different ages preferred to spend time (1) near a familiar cage mate versus an empty cage, or (2) near to a familiar cage mate versus direct contact with nesting material (tissues). Dwelling time in each of the test cages and sleeping sites was recorded, as was the behaviour of the test mice. Results indicated that when other conditions were similar, male mice preferred to sleep in close proximity to their familiar cage mate. Furthermore, the need to engage in active social behaviour increased with age. Tissues were used to a large extent for sleeping and sleep-related behaviour. It is concluded that single housing in order to avoid aggression between male mice is a solution with evident negative consequences for the animals. When individual housing is inevitable due to excessive aggressive behaviour, the presence of nesting material could partly compensate for the deprivation of social contact.

The influence of risk perception on biosafety level-2 laboratory workers' hand-to-face contact behaviors.

PubMed

Johnston, James D; Eggett, Dennis; Johnson, Michele J; Reading, James C

2014-01-01

Pathogen transmission in the laboratory is thought to occur primarily through inhalation of infectious aerosols or by direct contact with mucous membranes on the face. While significant research has focused on controlling inhalation exposures, little has been written about hand contamination and subsequent hand-to-face contact (HFC) transmission. HFC may present a significant risk to workers in biosafety level-2 (BSL-2) laboratories where there is typically no barrier between the workers' hands and face. The purpose of this study was to measure the frequency and location of HFC among BSL-2 workers, and to identify psychosocial factors that influence the behavior. Research workers (N = 93) from 21 BSL-2 laboratories consented to participate in the study. Two study personnel measured workers' HFC behaviors by direct observation during activities related to cell culture maintenance, cell infection, virus harvesting, reagent and media preparation, and tissue processing. Following observations, a survey measuring 11 psychosocial predictors of HFC was administered to participants. Study personnel recorded 396 touches to the face over the course of the study (mean = 2.6 HFCs/hr). Of the 93 subjects, 67 (72%) touched their face at least once, ranging from 0.2-16.0 HFCs/hr. Among those who touched their face, contact with the nose was most common (44.9%), followed by contact with the forehead (36.9%), cheek/chin (12.5%), mouth (4.0%), and eye (1.7%). HFC rates were significantly different across laboratories F(20, 72) = 1.85, p = 0.03. Perceived severity of infection predicted lower rates of HFC (p = 0.03). For every one-point increase in the severity scale, workers had 0.41 fewer HFCs/hr (r = -.27, P < 0.05). This study suggests HFC is common among BSL-2 laboratory workers, but largely overlooked as a major route of exposure. Workers' risk perceptions had a modest impact on their HFC behaviors, but other factors not considered in this study, including social modeling and

EFFICACY OF COMMERCIAL PRODUCTS IN ENHANCING OIL BIODEGRADATION IN CLOSED LABORATORY REACTORS

EPA Science Inventory

A laboratory screening protocol was designed and conducted to test the efficacy of eight commercial bacterial cultures and two non-bacterial products in enhancing the biodegradation of weathered Alaska North Slope crude oil in closed flasks. Three lines of evidence were used to ...

Numerical Simulations of Close and Contact Binary Systems Having Bipolytropic Equation of State

NASA Astrophysics Data System (ADS)

Kadam, Kundan; Clayton, Geoffrey C.; Motl, Patrick M.; Marcello, Dominic; Frank, Juhan

2017-01-01

I present the results of the numerical simulations of the mass transfer in close and contact binary systems with both stars having a bipolytropic (composite polytropic) equation of state. The initial binary systems are obtained by a modifying Hachisu’s self-consistent field technique. Both the stars have fully resolved cores with a molecular weight jump at the core-envelope interface. The initial properties of these simulations are chosen such that they satisfy the mass-radius relation, composition and period of a late W-type contact binary system. The simulations are carried out using two different Eulerian hydrocodes, Flow-ER with a fixed cylindrical grid, and Octo-tiger with an AMR capable cartesian grid. The detailed comparison of the simulations suggests an agreement between the results obtained from the two codes at different resolutions. The set of simulations can be treated as a benchmark, enabling us to reliably simulate mass transfer and merger scenarios of binary systems involving bipolytropic components.

Contact Binaries on Their Way Towards Merging

NASA Astrophysics Data System (ADS)

Gazeas, K.

2015-07-01

Contact binaries are the most frequently observed type of eclipsing star system. They are small, cool, low-mass binaries belonging to a relatively old stellar population. They follow certain empirical relationships that closely connect a number of physical parameters with each other, largely because of constraints coming from the Roche geometry. As a result, contact binaries provide an excellent test of stellar evolution, specifically for stellar merger scenarios. Observing campaigns by many authors have led to the cataloging of thousands of contact binaries and enabled statistical studies of many of their properties. A large number of contact binaries have been found to exhibit extraordinary behavior, requiring follow-up observations to study their peculiarities in detail. For example, a doubly-eclipsing quadruple system consisting of a contact binary and a detached binary is a highly constrained system offering an excellent laboratory to test evolutionary theories for binaries. A new observing project was initiated at the University of Athens in 2012 in order to investigate the possible lower limit for the orbital period of binary systems before coalescence, prior to merging.

Comparing Chalk With Cheese-The EGG Contact Quotient Is Only a Limited Surrogate of the Closed Quotient.

PubMed

Herbst, Christian T; Schutte, Harm K; Bowling, Daniel L; Svec, Jan G

2017-07-01

The electroglottographic (EGG) contact quotient (CQegg), an estimate of the relative duration of vocal fold contact per vibratory cycle, is the most commonly used quantitative analysis parameter in EGG. The purpose of this study is to quantify the CQegg's relation to the closed quotient, a measure more directly related to glottal width changes during vocal fold vibration and the respective sound generation events. Thirteen singers (six females) phonated in four extreme phonation types while independently varying the degree of breathiness and vocal register. EGG recordings were complemented by simultaneous videokymographic (VKG) endoscopy, which allows for calculation of the VKG closed quotient (CQvkg). The CQegg was computed with five different algorithms, all used in previous research. All CQegg algorithms produced CQegg values that clearly differed from the respective CQvkg, with standard deviations around 20% of cycle duration. The difference between CQvkg and CQegg was generally greater for phonations with lower CQvkg. The largest differences were found for low-quality EGG signals with a signal-to-noise ratio below 10 dB, typically stemming from phonations with incomplete glottal closure. Disregarding those low-quality signals, we found the best match between CQegg and CQvkg for a CQegg algorithm operating on the first derivative of the EGG signal. These results show that the terms "closed quotient" and "contact quotient" should not be used interchangeably. They relate to different physiological phenomena. Phonations with incomplete glottal closure having an EGG signal-to-noise ratio below 10 dB are not suited for CQegg analysis. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

Ring-Closing Metathesis: An Advanced Guided-Inquiry Experiment for the Organic Laboratory

ERIC Educational Resources Information Center

Schepmann, Hala G.; Mynderse, Michelle

2010-01-01

The design and implementation of an advanced guided-inquiry experiment for the organic laboratory is described. Grubbs's second-generation catalyst is used to effect the ring-closing metathesis of diethyl diallylmalonate. The reaction is carried out under an inert atmosphere at room temperature and monitored by argentic TLC. The crude reaction is…

[Laboratory study of the cytotoxicity of colored soft contact lenses].

PubMed

Almesmary, A A

1999-01-01

In the clinical practice we have met with the fact that some patients did not tolerate soft coloured contact lenses even when they used them for a short time. To find whether the cause is the composition of these lenses, mainly the adding of stain, he used the laboratory test to determine cytotoxicity, the test of dynamic observation of cytotoxicity where the cells cultured in vitro are the experimental object. On the basis of the results of this test commonly used for the determination of the cytotoxicity of implantation materials, he thinks that the cause of intolerance of coloured lenses is not their toxicity but other phenomena. An individual hypersensitivity or insufficient care of lenses (the influence of disinfectants) can be among these causes.

Contact Thermocouple Methodology and Evaluation for Temperature Measurement in the Laboratory

NASA Technical Reports Server (NTRS)

Brewer, Ethan J.; Pawlik, Ralph J.; Krause, David L.

2013-01-01

Laboratory testing of advanced aerospace components very often requires highly accurate temperature measurement and control devices, as well as methods to precisely analyze and predict the performance of such components. Analysis of test articles depends on accurate measurements of temperature across the specimen. Where possible, this task is accomplished using many thermocouples welded directly to the test specimen, which can produce results with great precision. However, it is known that thermocouple spot welds can initiate deleterious cracks in some materials, prohibiting the use of welded thermocouples. Such is the case for the nickel-based superalloy MarM-247, which is used in the high temperature, high pressure heater heads for the Advanced Stirling Converter component of the Advanced Stirling Radioisotope Generator space power system. To overcome this limitation, a method was developed that uses small diameter contact thermocouples to measure the temperature of heater head test articles with the same level of accuracy as welded thermocouples. This paper includes a brief introduction and a background describing the circumstances that compelled the development of the contact thermocouple measurement method. Next, the paper describes studies performed on contact thermocouple readings to determine the accuracy of results. It continues on to describe in detail the developed measurement method and the evaluation of results produced. A further study that evaluates the performance of different measurement output devices is also described. Finally, a brief conclusion and summary of results is provided.

Personal value preferences, group identifications, and cultural practices of Palestinian Israelis working in close contact with Jewish Israelis.

PubMed

Tartakovsky, Eugene; Abu Kheit, Ayat

2017-01-01

The present study investigates the connection between personal value preferences, group identifications, and cultural practices among Palestinian Israelis working in close contact with the Jewish population in Israel. One hundred twenty-two Palestinian Israelis participated in the study. The participants were employed in different professional positions in the Tel Aviv Metropolitan area and were recruited to the study using the snowball technique. A stronger national identification was associated with a higher preference for the security and conformity values, and a lower preference for the humility values. A stronger ethnic identification was associated with a lower preference for the security, power, and stimulation values. Group identifications mediated the connection between personal value preferences and cultural practices. A longer time working in close contact with the majority group and less frequent visits home were associated with a greater adherence to the majority group's cultural practices but not with adherence to the ethnic group's practices and not with the group identifications.

Anatomic double-bundle anterior cruciate ligament reconstruction restores patellofemoral contact areas and pressures more closely than nonanatomic single-bundle reconstruction.

PubMed

Tajima, Goro; Iriuchishima, Takanori; Ingham, Sheila J M; Shen, Wei; van Houten, Albert H; Aerts, Maarten M; Shimamura, Tadashi; Smolinski, Patrick; Fu, Freddie H

2010-10-01

To investigate the effects of anterior cruciate ligament (ACL) deficiency and nonanatomic single-bundle (SB) and anatomic double-bundle (DB) ACL reconstruction on the contact characteristics of the patellofemoral (PF) joint. By use of a materials testing system, 7 fresh-frozen human cadaveric knees were tested. The following states were tested: ACL-intact knee, nonanatomic SB ACL reconstruction, anatomic DB ACL reconstruction, and ACL-deficient knee. Hamstring autografts were used. PF contact pressures and areas were measured with pressure-sensitive film at 30°, 60°, and 90° of knee flexion with a constant 100-N load on the quadriceps tendon. The total contact area of ACL-deficient and nonanatomic SB ACL-reconstructed knees (123.8 ± 63.9 and 149.6 ± 79.3 mm(2), respectively) significantly decreased when compared with those of the intact knee (206.1 ± 83.6 mm(2)) at 30° of knee flexion. The lateral-facet peak pressure of ACL-deficient and nonanatomic SB ACL-reconstructed knees (1.12 ± 0.52 and 1.22 ± 0.54 MPa, respectively) significantly decreased when compared with those of the intact knee (0.68 ± 0.38 MPa) at 90° of knee flexion. Anatomic DB ACL reconstruction restored the contact pressures and areas to values similar to those of the intact knee (no significant difference). ACL deficiency resulted in a significant decrease in the total and medial PF contact areas and in an increase in the lateral PF contact pressure. Anatomic DB ACL reconstruction more closely restored normal PF contact area and pressure than did nonanatomic SB ACL reconstruction. Our findings suggest that the changes in the PF contact area and pressures in ACL deficiency and after nonanatomic SB ACL reconstruction may be one of the causes of PF osteoarthritis or other related PF problems found at long-term follow-up. Anatomic DB ACL reconstruction may reduce the incidence of PF problems by closely restoring the contact area and pressure. Copyright © 2010 Arthroscopy Association of

Is the Colonisation of Staphylococcus aureus in Pets Associated with Their Close Contact with Owners?

PubMed Central

Bierowiec, Karolina; Płoneczka-Janeczko, Katarzyna; Rypuła, Krzysztof

2016-01-01

In human beings and animals, staphylococci constitute part of the normal microbial population. Staphylococcus aureus could be classified as an opportunistic pathogen because the bacteria are noted in clinically healthy individuals, but when the immune system becomes compromised, they can also cause a wide range of infections. The objective of this study was to test the hypothesis that cats who are in close contact with their owners are at the greatest risk of being colonised with S. aureus. Two groups of cats were investigated: single, pet (domestic) cats that do not have outdoor access; and a local population of feral cats living in urban areas. The prevalence of S. aureus in domestic cats was 19.17%, while it’s prevalence in the feral cat population was only 8.3%; which was statistically significant. Analysis of antibiotic resistance, at the genotypic as well as phenotypic level, showed that S. aureus isolates from pet cats were more likely to harbour antibiotic resistant determinants. The prevalence of methicillin-resistant Staphylococcus aureus (MRSA) in households was 10.21%, while in feral cats it was only 1.4%. In conclusion, this study has revealed a correlation between close contact with humans and a higher risk of the cats being colonised with S. aureus and harbouring the antibiotic resistant determinants. PMID:27227897

Initial experimental results from the Laboratory Biosphere closed ecological system facility

NASA Astrophysics Data System (ADS)

Alling, A.; Allen, J.; Dempster, W.; Nelson, M.; Silverstone, S.; van Thillo, M.

Results from the closure and initial closed ecological system research in the "Laboratory Biosphere" facility in Santa Fe, New Mexico (USA) will be presented. The facility was initially sealed in April 2002; and the first crop experiments with soybeans commenced in May 2002. The Laboratory Biosphere was created by the team which invented, built and operated Biosphere 2 during its years of closed ecological system functioning (1991-94) and is a testbed to build upon the lessons learned. It is an opportunity to continue experiments with a sustainable soil based agriculture system unlike most bioregenerative systems which use hydroponic systems dependent on a supply of nutrient solution. Because of the small volume of the system (34-45 m3), developing mechanisms to keep parameters like carbon dioxide within acceptable limits will be critical. Recycle of nutrients within the system to maintain soil fertility; and the ability of the inherent complex ecology of soils and a soil bed reactor to handle trace gas buildups are primary research goals. Other research goals are determination of short and long-term exchanges between soil, plants and atmosphere, especially for carbon dioxide, oxygen, nitrogen, NOX, and methane, impact of cultivation (tillage) on soil/atmospheric exchanges., investigation and development of strategies to return nutrients to the soil to maintain fertility, e.g. shredding biomass vs. composting, impact on soil chemistry of returning leachate water to the soil as irrigation water. The microbiological status of soils prior to experiments and over time will allow measurement of changes in microbial diversity and the determination of the role of soil microbes in biogeochemical cycles. Integration of automated sensor and control in the system with real-time modeling has importance for operation, research and educational outreach programs. The Laboratory Biosphere is intended to test and develop a "cybersphere" (network of shared intelligence) that may be

Techniques for Solution- Assisted Optical Contacting

NASA Technical Reports Server (NTRS)

DeVine, Glenn; Ware, Brent; Wuchenich, Danielle M.; Spero, Robert E.; Klipstein, William M.; McKenzie, Kirk

2012-01-01

A document discusses a solution-assisted contacting technique for optical contacting. An optic of surface flatness Lambda/20 was successfully contacted with one of moderate surface quality, or Lambda/4. Optics used were both ultra-low expansion (ULE) glass (Lambda/4 and Lambda/20) and fused silica (Lambda/20). A stainless steel template of the intended interferometer layout was designed and constructed with three contact points per optic. The contact points were all on a common side of the template. The entire contacting jig was tilted at about 30 . Thus, when the isopropanol was applied, each optic slid due to gravity, resting on the contact points. All of the contacting was performed in a relatively dusty laboratory. A number of successful contacts were achieved where up to two or three visible pieces of dust could be seen. These were clearly visible due to refraction patterns between the optic and bench. On a number of optics, the final step of dropping isopropyl between the surfaces was repeated until a successful contact was achieved. The new procedures realized in this work represent a simplification for optical contacting in the laboratory. They will both save time and money spent during the contacting process, and research and development phases. The techniques outlined are suitable for laboratory experiments, research, and initial development stages.

Fabricating customized hydrogel contact lens

NASA Astrophysics Data System (ADS)

Childs, Andre; Li, Hao; Lewittes, Daniella M.; Dong, Biqin; Liu, Wenzhong; Shu, Xiao; Sun, Cheng; Zhang, Hao F.

2016-10-01

Contact lenses are increasingly used in laboratories for in vivo animal retinal imaging and pre-clinical studies. The lens shapes often need modification to optimally fit corneas of individual test subjects. However, the choices from commercially available contact lenses are rather limited. Here, we report a flexible method to fabricate customized hydrogel contact lenses. We showed that the fabricated hydrogel is highly transparent, with refractive indices ranging from 1.42 to 1.45 in the spectra range from 400 nm to 800 nm. The Young’s modulus (1.47 MPa) and hydrophobicity (with a sessile drop contact angle of 40.5°) have also been characterized experimentally. Retinal imaging using optical coherence tomography in rats wearing our customized contact lenses has the quality comparable to the control case without the contact lens. Our method could significantly reduce the cost and the lead time for fabricating soft contact lenses with customized shapes, and benefit the laboratorial-used contact lenses in pre-clinical studies.

Fabricating customized hydrogel contact lens

PubMed Central

Childs, Andre; Li, Hao; Lewittes, Daniella M.; Dong, Biqin; Liu, Wenzhong; Shu, Xiao; Sun, Cheng; Zhang, Hao F.

2016-01-01

Contact lenses are increasingly used in laboratories for in vivo animal retinal imaging and pre-clinical studies. The lens shapes often need modification to optimally fit corneas of individual test subjects. However, the choices from commercially available contact lenses are rather limited. Here, we report a flexible method to fabricate customized hydrogel contact lenses. We showed that the fabricated hydrogel is highly transparent, with refractive indices ranging from 1.42 to 1.45 in the spectra range from 400 nm to 800 nm. The Young’s modulus (1.47 MPa) and hydrophobicity (with a sessile drop contact angle of 40.5°) have also been characterized experimentally. Retinal imaging using optical coherence tomography in rats wearing our customized contact lenses has the quality comparable to the control case without the contact lens. Our method could significantly reduce the cost and the lead time for fabricating soft contact lenses with customized shapes, and benefit the laboratorial-used contact lenses in pre-clinical studies. PMID:27748361

Familiarity breeds contempt: combining proximity loggers and GPS reveals female white-tailed deer (Odocoileus virginianus) avoiding close contact with neighbors.

PubMed

Tosa, Marie I; Schauber, Eric M; Nielsen, Clayton K

2015-01-01

Social interactions can influence infectious disease dynamics, particularly for directly transmitted pathogens. Therefore, reliable information on contact frequency within and among groups can better inform disease modeling and management. We compared three methods of assessing contact patterns: (1) space-use overlap (volume of interaction [VI]), (2) direct contact rates measured by simultaneous global positioning system (GPS) locations (<10 m apart), and (3) direct contact rates measured by proximity loggers (PLs; 1-m detection) among female white-tailed deer (Odocoileus virginianus). We calculated the PL∶GPS contact ratios to see whether both devices reveal similar contact patterns and thus predict similar pathogen transmission patterns. Contact rates measured by GPS and PLs were similarly high for two within-group dyads (pairs of deer in the same social groups). Dyads representing separate but neighboring groups (high VI) had PL∶GPS contact ratios near zero, whereas dyads further apart (intermediate VI) had higher PL∶GPS contact ratios. Social networks based on PL contacts showed the fewest connected individuals and lowest mean centrality measures; network metrics were intermediate when based on GPS contacts and greatest when based on VI. Thus, the VI network portrayed animals to be more uniformly and strongly connected than did the PL network. We conclude that simultaneous GPS locations, compared with PLs, substantially underestimate the impact of group membership on direct contact rates of female deer and make networks appear more connected. We also present evidence that deer coming within the general vicinity of each other are less likely to come in close contact if they are in neighboring social groups than deer whose home ranges overlap little if at all. Combined, these results provide evidence that direct transmission of disease agents among female and juvenile white-tailed deer is likely to be constrained both spatially and by social structure, more

Dynamics of visual feedback in a laboratory simulation of a penalty kick.

PubMed

Morya, Edgard; Ranvaud, Ronald; Pinheiro, Walter Machado

2003-02-01

Sport scientists have devoted relatively little attention to soccer penalty kicks, despite their decisive role in important competitions such as the World Cup. Two possible kicker strategies have been described: ignoring the goalkeeper action (open loop) or trying to react to the goalkeeper action (closed loop). We used a paradigm simulating a penalty kick in the laboratory to investigate the dynamics of the closed-loop strategy in these controlled conditions. The probability of correctly responding to the simulated goalkeeper motion as a function of time available followed a logistic curve. Kickers on average reached perfect performance only if the goalkeeper committed him or herself to one side about 400 ms before ball contact and showed chance performance if the goalkeeper motion occurred less than 150 ms before ball contact. Interestingly, coincidence judgement--another aspect of the laboratory responses--appeared to be affected for a much longer time (> 500 ms) than was needed to correctly determine laterality. The present study is meant as groundwork for experiments in more ecological conditions applicable to kickers and goalkeepers.

Sandia National Laboratories: Contact Us

Science.gov Websites

Technology Partnerships Business, Industry, & Non-Profits Government Universities Center for Development Agreement (CRADA) Strategic Partnership Projects, Non-Federal Entity (SPP/NFE) Agreements New )* Non-mail deliveries: 1515 Eubank SE Albuquerque, NM 87123 Sandia National Laboratories, California P.O

Anti HIV-2 serological screening in Portuguese populations native from or having had close contact with Africa.

PubMed

Saal, F; Sidibe, S; Alves-Cardoso, E; Terrinha, A; Gessain, A; Poirot, Y; Montagnier, L; Peries, J

1987-01-01

To gather epidemiologic information on the spread of human immunodeficiency virus (HIV)-2 in Portugal, sera were collected in 1985 from 156 healthy adults currently living in Portugal but natives of Guinea Bissau, Cape Verde Islands, Saint Tome/Prince, Angola, and Mozambique and from 321 native Portuguese men and women who had close contact with local African populations. As a control, sera were collected from 102 health Portuguese with no previous contact with Africa or African natives. The enzyme-linked immunosorbent assay (ELISA) developed by Diagnostic Pasteur was used to screen for antibodies to HIV. No positive reactions were recorded in the control population. In contracts, 9 (6%) of the African natives and 7 (2%) of the contacts of Africans were HIV-positive, 6 of the positive sera were from women and 10 were from men. Significantly, 1 of the HIV-2-positive serum samples was from a native of Mozambique and 3 were from natives of Angola. This suggests that HIV-2 infection may have spread to other former Portuguese colonies, and foreign army soldiers who were at 1 time residents of Mozambique or Angola should be considered a risk group capable of spreading HIV-2 infection to other countries.

Laboratory demonstrations on a pyramid wavefront sensor without modulation for closed-loop adaptive optics system.

PubMed

Wang, Shengqian; Rao, Changhui; Xian, Hao; Zhang, Jianlin; Wang, Jianxin; Liu, Zheng

2011-04-25

The feasibility and performance of the pyramid wavefront sensor without modulation used in closed-loop adaptive optics system is investigated in this paper. The theory concepts and some simulation results are given to describe the detection trend and the linearity range of such a sensor with the aim to better understand its properties, and then a laboratory setup of the adaptive optics system based on this sensor and the liquid-crystal spatial light modulator is built. The correction results for the individual Zernike aberrations and the Kolmogorov phase screens are presented to demonstrate that the pyramid wavefront sensor without modulation can work as expected for closed-loop adaptive optics system.

Fingertip contact influences human postural control

NASA Technical Reports Server (NTRS)

Jeka, J. J.; Lackner, J. R.

1994-01-01

Touch and pressure stimulation of the body surface can strongly influence apparent body orientation, as well as the maintenance of upright posture during quiet stance. In the present study, we investigated the relationship between postural sway and contact forces at the fingertip while subjects touched a rigid metal bar. Subjects were tested in the tandem Romberg stance with eyes open or closed under three conditions of fingertip contact: no contact, touch contact (< 0.98 N of force), and force contact (as much force as desired). Touch contact was as effective as force contact or sight of the surroundings in reducing postural sway when compared to the no contact, eyes closed condition. Body sway and fingertip forces were essentially in phase with force contact, suggesting that fingertip contact forces are physically counteracting body sway. Time delays between body sway and fingertip forces were much larger with light touch contact, suggesting that the fingertip is providing information that allows anticipatory innervation of musculature to reduce body sway. The results are related to observations on precision grip as well as the somatosensory, proprioceptive, and motor mechanisms involved in the reduction of body sway.

Timeliness of contact tracing among flight passengers for influenza A/H1N1 2009

PubMed Central

2011-01-01

Background During the initial containment phase of influenza A/H1N1 2009, close contacts of cases were traced to provide antiviral prophylaxis within 48 h after exposure and to alert them on signs of disease for early diagnosis and treatment. Passengers seated on the same row, two rows in front or behind a patient infectious for influenza, during a flight of ≥ 4 h were considered close contacts. This study evaluates the timeliness of flight-contact tracing (CT) as performed following national and international CT requests addressed to the Center of Infectious Disease Control (CIb/RIVM), and implemented by the Municipal Health Services of Schiphol Airport. Methods Elapsed days between date of flight arrival and the date passenger lists became available (contact details identified - CI) was used as proxy for timeliness of CT. In a retrospective study, dates of flight arrival, onset of illness, laboratory diagnosis, CT request and identification of contacts details through passenger lists, following CT requests to the RIVM for flights landed at Schiphol Airport were collected and analyzed. Results 24 requests for CT were identified. Three of these were declined as over 4 days had elapsed since flight arrival. In 17 out of 21 requests, contact details were obtained within 7 days after arrival (81%). The average delay between arrival and CI was 3,9 days (range 2-7), mainly caused by delay in diagnosis of the index patient after arrival (2,6 days). In four flights (19%), contacts were not identified or only after > 7 days. CI involving Dutch airlines was faster than non-Dutch airlines (P < 0,05). Passenger locator cards did not improve timeliness of CI. In only three flights contact details were identified within 2 days after arrival. Conclusion CT for influenza A/H1N1 2009 among flight passengers was not successful for timely provision of prophylaxis. CT had little additional value for alerting passengers for disease symptoms, as this information already was provided

Apparent contact angle and contact angle hysteresis on liquid infused surfaces.

PubMed

Semprebon, Ciro; McHale, Glen; Kusumaatmaja, Halim

2016-12-21

We theoretically investigate the apparent contact angle and contact angle hysteresis of a droplet placed on a liquid infused surface. We show that the apparent contact angle is not uniquely defined by material parameters, but also has a dependence on the relative size between the droplet and its surrounding wetting ridge formed by the infusing liquid. We derive a closed form expression for the contact angle in the limit of vanishing wetting ridge, and compute the correction for small but finite ridge, which corresponds to an effective line tension term. We also predict contact angle hysteresis on liquid infused surfaces generated by the pinning of the contact lines by the surface corrugations. Our analytical expressions for both the apparent contact angle and contact angle hysteresis can be interpreted as 'weighted sums' between the contact angles of the infusing liquid relative to the droplet and surrounding gas phases, where the weighting coefficients are given by ratios of the fluid surface tensions.

Nobel Chemistry in the Laboratory: Synthesis of a Ruthenium Catalyst for Ring-Closing Olefin Metathesis--An Experiment for the Advanced Inorganic or Organic Laboratory

ERIC Educational Resources Information Center

Greco, George E.

2007-01-01

An experiment for the upper-level undergraduate laboratory is described in which students synthesize a ruthenium olefin metathesis catalyst, then use the catalyst to carry out the ring-closing metathesis of diethyl diallylmalonate. The olefin metathesis reaction was the subject of the 2005 Nobel Prize in chemistry. The catalyst chosen for this…

Seroepidemiological survey on Rift Valley fever among small ruminants and their close human contacts in Makkah, Saudi Arabia, in 2011.

PubMed

Mohamed, A M; Ashshi, A M; Asghar, A H; Abd El-Rahim, I H A; El-Shemi, A G; Zafar, T

2014-12-01

This study describes a seroepidemiological survey on Rift Valley fever (RVF) among small ruminants and their close human contacts in Makkah, Saudi Arabia. A total of 500 small ruminants (126 local, 374 imported) were randomly selected from the sacrifice livestock yards of Al-Kaakiah slaughterhouse, in the holy city of Makkah, during the pilgrimage season 1432 H (4-9 November 2011). In addition, blood samples were collected from 100 local workers in close contact with the animals at the slaughterhouse. An RVF competition multi-species enzyme-linked immunosorbent assay (ELISA) detecting anti-RVF virus immunoglobulin G (IgG)/ immunoglobulin M (IgM) antibodies and an RVF IgM-specific ELISA were used for serological investigations. In total, 84 (16.8%) of the 500 sacrificial sheep and goats tested seropositive in the competition ELISA but no IgM antibodies were detected in the IgM-specific assay. All seropositive samples, comprising 17.91% of the imported animals and 13.49% of the local ones, were therefore designated positive for anti-RVF virus IgG antibody. Among the local personnel working in close contact with the animals, 9% tested seropositive in the RVF competition ELISA. The study indicates that two factors may increase the likelihood of an RVF outbreak among sacrificial animals and pilgrims: i) the large-scale importation of small ruminants into Saudi Arabia from the Horn of Africa shortly before the pilgrimage season, and ii) the movement of animals within Saudi Arabia, from the RVF-endemic south-western area (Jizan region) to the Makkah region, particularly in the few weeks before the pilgrimage season. From these findings, it is recommended that i) all regulations concerning the import of animals into Saudi Arabia from Africa should be rigorously applied, particularly the RVF vaccination of all ruminants destined for export at least two weeks before exportation, and ii) the movement of animals from the RVF-endemic south-western area (Jizan region) of Saudi

The association of a heart attack or stroke with depressive symptoms stratified by the presence of a close social contact: findings from the National Health and Aging Trends Study Cohort.

PubMed

Simning, Adam; Seplaki, Christopher L; Conwell, Yeates

2018-01-01

The objective of the study is to examine whether the risk of having clinically significant depressive symptoms following a heart attack or stroke varies by the presence of a close social contact. The National Health and Aging Trends Study is a nationally representative longitudinal survey of US Medicare beneficiaries aged 65 and older initiated in 2011. A total of 5643 older adults had information on social contacts at baseline and depressive symptoms at the 1-year follow-up interview. The two-item Patient Health Questionnaire identified clinically significant depressive symptoms. Interview questions examined social contacts and the presence of self-reported heart attack or stroke during the year of follow-up. A total of 297 older adults reported experiencing a heart attack and/or stroke between their baseline and follow-up interviews. In regression analyses accounting for sociodemographics, baseline depressive symptoms, medical comorbidity, and activities of daily living impairment, older adults with no close social contacts had increased odds of depressive symptoms at follow-up after experiencing a heart attack or stroke, while those with close social contacts had increased odds of depressive symptoms at follow-up after experiencing a stroke, but not a heart attack. Older adults have increased odds of having depressive symptoms following a self-reported stroke, but only those with no close social contacts had increased odds of depressive symptoms following a heart attack. Social networks may play a role in the mechanisms underlying depression among older adults experiencing certain acute health events. Future work exploring the potential causal relationships suggested here, if confirmed, could inform interventions to alleviate or prevent depression among at risk older adults. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Gunshot residue patterns on skin in angled contact and near contact gunshot wounds.

PubMed

Plattner, T; Kneubuehl, B; Thali, M; Zollinger, U

2003-12-17

The goal of this study was the reproduction of shape and pattern of gunshot residues in near contact and contact gunshot wounds by a series of experimental gunshots on a skin and soft tissue model. The aim was to investigate the shape and direction of soot deposits with regard to the muzzle according to different muzzle-target angles, firing distances, type of ammunition and weapon and barrel length. Based on a review of the literature and on the results of the experiments the authors could make the following statements of gunshot residues in angled contact and close contact gunshot: (1) gunshot residues on the target surface can be differentiated in a "inner" and "outer powder soot zone"; (2) the outer powder soot zone is much less visible than the inner powder soot zone and may lack on human skin; (3) with increasing muzzle target distance both inner and outer powder soot halo increase in size and decrease in density; (4) in angled shots the inner powder soot halo shows an eccentric, elliptic shape which points towards the muzzle, regardless of ammunition, calibre and barrel length; (5) the outer powder soot points away from the muzzle in angled contact and close contact shots.

Contact material optimization and contact physics in metal-contact microelectromechanical systems (MEMS) switches

NASA Astrophysics Data System (ADS)

Yang, Zhenyin

Metal-contact MEMS switches hold great promise for implementing agile radio frequency (RF) systems because of their small size, low fabrication cost, low power consumption, wide operational band, excellent isolation and exceptionally low signal insertion loss. Gold is often utilized as a contact material for metal-contact MEMS switches due to its excellent electrical conductivity and corrosion resistance. However contact wear and stiction are the two major failure modes for these switches due to its material softness and high surface adhesion energy. To strengthen the contact material, pure gold was alloyed with other metal elements. We designed and constructed a new micro-contacting test facility that closely mimic the typical MEMS operation and utilized this facility to efficiently evaluate optimized contact materials. Au-Ni binary alloy system as the candidate contact material for MEMS switches was systematically investigated. A correlation between contact material properties (etc. microstructure, micro-hardness, electrical resistivity, topology, surface structures and composition) and micro-contacting performance was established. It was demonstrated nano-scale graded two-phase Au-Ni film could possibly yield an improved device performance. Gold micro-contact degradation mechanisms were also systematically investigated by running the MEMS switching tests under a wide range of test conditions. According to our quantitative failure analysis, field evaporation could be the dominant failure mode for highfield (> critical threshold field) hot switching; transient thermal-assisted wear could be the dominant failure mode for low-field hot switching; on the other hand, pure mechanical wear and steady current heating (1 mA) caused much less contact degradation in cold switching tests. Results from low-force (50 muN/micro-contact), low current (0.1 mA) tests on real MEMS switches indicated that continuous adsorbed films from ambient air could degrade the switch contact

Multiplex PCR technique could be an alternative approach for early detection of leprosy among close contacts--a pilot study from India.

PubMed

Banerjee, Surajita; Sarkar, Kamalesh; Gupta, Soma; Mahapatra, Prasanta Sinha; Gupta, Siddhartha; Guha, Samudra; Bandhopadhayay, Debasis; Ghosal, Chaitry; Paine, Suman Kalyan; Dutta, Rathindra Nath; Biswas, Nibir; Bhattacharya, Basudev

2010-08-24

Implementation of Multi drug Therapy (MDT) regimen has resulted in the decline of the total number of leprosy cases in the world. Though the prevalence rate has been declining, the incidence rate remains more or less constant and high in South East Asian countries particularly in India, Nepal, Bangladesh, Pakistan and Srilanka. Leprosy, particularly that of multibacillary type spreads silently before it is clinically detected. An early detection and treatment would help to prevent transmission in the community. Multiplex PCR (M-PCR) technique appears to be promising towards early detection among contacts of leprosy cases. A total of 234 paucibacillary (PB) and 205 multibacillary (MB) leprosy cases were studied in a community of an endemic area of Bankura district of West Bengal (Eastern India). They were assessed by smear examination for acid-fast bacilli (AFB) and M-PCR technique. These patients were treated with Multidrug Therapy (MDT) as prescribed by WHO following detection. A total of 110 MB and 72 PB contacts were studied by performing M-PCR in their nasal swab samples. 83.4% of MB patients were observed to be positive by smear examination for AFB and 89.2% by M-PCR. While 22.2% of PB patients were found to be positive by smear examination for AFB, 80.3% of these patients were positive by M-PCR. Among leprosy contacts (using M-PCR), 10.9% were found to be positive among MB contacts and 1.3% among PB contacts. Interestingly, two contacts of M-PCR positive MB cases developed leprosy during the period of two years follow up. The M-PCR technique appears to be an efficient tool for early detection of leprosy cases in community based contact tracing amongst close associates of PB and MB cases. Early contact tracing using a molecular biology tool can be of great help in curbing the incidence of leprosy further.

Applicability of contact angle techniques used in the analysis of contact lenses, part 1: comparative methodologies.

PubMed

Campbell, Darren; Carnell, Sarah Maria; Eden, Russell John

2013-05-01

Contact angle, as a representative measure of surface wettability, is often employed to interpret contact lens surface properties. The literature is often contradictory and can lead to confusion. This literature review is part of a series regarding the analysis of hydrogel contact lenses using contact angle techniques. Here we present an overview of contact angle terminology, methodology, and analysis. Having discussed this background material, subsequent parts of the series will discuss the analysis of contact lens contact angles and evaluate differences in published laboratory results. The concepts of contact angle, wettability and wetting are presented as an introduction. Contact angle hysteresis is outlined and highlights the advantages in using dynamic analytical techniques over static methods. The surface free energy of a material illustrates how contact angle analysis is capable of providing supplementary surface characterization. Although single values are able to distinguish individual material differences, surface free energy and dynamic methods provide an improved understanding of material behavior. The frequently used sessile drop, captive bubble, and Wilhelmy plate techniques are discussed. Their use as both dynamic and static methods, along with the advantages and disadvantages of each technique, is explained. No single contact angle technique fully characterizes the wettability of a material surface, and the application of complimenting methods allows increased characterization. At present, there is not an ISO standard method designed for soft materials. It is important that each contact angle technique has a standard protocol, as small protocol differences between laboratories often contribute to a variety of published data that are not easily comparable.

Contact Us | Frederick National Laboratory for Cancer Research

Cancer.gov

The ATOM Consortium is actively seeking additional partnerships with qualified pharma, biotech, technology, academic, government, and other organizations. If you are interested in getting involved,please contact: info@atomscience.org F

Validation of Contact-Free Sleep Monitoring Device with Comparison to Polysomnography

PubMed Central

Tal, Asher; Shinar, Zvika; Shaki, David; Codish, Shlomi; Goldbart, Aviv

2017-01-01

Study Objectives: To validate a contact-free system designed to achieve maximal comfort during long-term sleep monitoring, together with high monitoring accuracy. Methods: We used a contact-free monitoring system (EarlySense, Ltd., Israel), comprising an under-the-mattress piezoelectric sensor and a smartphone application, to collect vital signs and analyze sleep. Heart rate (HR), respiratory rate (RR), body movement, and calculated sleep-related parameters from the EarlySense (ES) sensor were compared to data simultaneously generated by the gold standard, polysomnography (PSG). Subjects in the sleep laboratory underwent overnight technician-attended full PSG, whereas subjects at home were recorded for 1 to 3 nights with portable partial PSG devices. Data were compared epoch by epoch. Results: A total of 63 subjects (85 nights) were recorded under a variety of sleep conditions. Compared to PSG, the contact-free system showed similar values for average total sleep time (TST), % wake, % rapid eye movement, and % non-rapid eye movement sleep, with 96.1% and 93.3% accuracy of continuous measurement of HR and RR, respectively. We found a linear correlation between TST measured by the sensor and TST determined by PSG, with a coefficient of 0.98 (R = 0.87). Epoch-by-epoch comparison with PSG in the sleep laboratory setting revealed that the system showed sleep detection sensitivity, specificity, and accuracy of 92.5%, 80.4%, and 90.5%, respectively. Conclusions: TST estimates with the contact-free sleep monitoring system were closely correlated with the gold-standard reference. This system shows good sleep staging capability with improved performance over accelerometer-based apps, and collects additional physiological information on heart rate and respiratory rate. Citation: Tal A, Shinar Z, Shaki D, Codish S, Goldbart A. Validation of contact-free sleep monitoring device with comparison to polysomnography. J Clin Sleep Med. 2017;13(3):517–522. PMID:27998378

Microscale hydrodynamics near moving contact lines

NASA Technical Reports Server (NTRS)

Garoff, Stephen; Chen, Q.; Rame, Enrique; Willson, K. R.

1994-01-01

The hydrodynamics governing the fluid motions on a microscopic scale near moving contact lines are different from those governing motion far from the contact line. We explore these unique hydrodynamics by detailed measurement of the shape of a fluid meniscus very close to a moving contact line. The validity of present models of the hydrodynamics near moving contact lines as well as the dynamic wetting characteristics of a family of polymer liquids are discussed.

ELECTRIC CONTACT MEANS

DOEpatents

Grear, J.W. Jr.

1959-03-10

A switch adapted to maintain electrical connections under conditions of vibration or acceleration is described. According to the invention, thc switch includes a rotatable arm carrying a conductive bar arranged to close against two contacts spaced in the same plane. The firm and continuous engagement of the conductive bar with the contacts is acheived by utilizeing a spring located betwenn the vbar and athe a rem frzme and slidable mounting the bar in channel between two arms suspendef from the arm frame.

Validation of Contact-Free Sleep Monitoring Device with Comparison to Polysomnography.

PubMed

Tal, Asher; Shinar, Zvika; Shaki, David; Codish, Shlomi; Goldbart, Aviv

2017-03-15

To validate a contact-free system designed to achieve maximal comfort during long-term sleep monitoring, together with high monitoring accuracy. We used a contact-free monitoring system (EarlySense, Ltd., Israel), comprising an under-the-mattress piezoelectric sensor and a smartphone application, to collect vital signs and analyze sleep. Heart rate (HR), respiratory rate (RR), body movement, and calculated sleep-related parameters from the EarlySense (ES) sensor were compared to data simultaneously generated by the gold standard, polysomnography (PSG). Subjects in the sleep laboratory underwent overnight technician-attended full PSG, whereas subjects at home were recorded for 1 to 3 nights with portable partial PSG devices. Data were compared epoch by epoch. A total of 63 subjects (85 nights) were recorded under a variety of sleep conditions. Compared to PSG, the contact-free system showed similar values for average total sleep time (TST), % wake, % rapid eye movement, and % non-rapid eye movement sleep, with 96.1% and 93.3% accuracy of continuous measurement of HR and RR, respectively. We found a linear correlation between TST measured by the sensor and TST determined by PSG, with a coefficient of 0.98 (R = 0.87). Epoch-by-epoch comparison with PSG in the sleep laboratory setting revealed that the system showed sleep detection sensitivity, specificity, and accuracy of 92.5%, 80.4%, and 90.5%, respectively. TST estimates with the contact-free sleep monitoring system were closely correlated with the gold-standard reference. This system shows good sleep staging capability with improved performance over accelerometer-based apps, and collects additional physiological information on heart rate and respiratory rate. © 2017 American Academy of Sleep Medicine

A Laboratory Assessment of Factors That Affect Bacterial Adhesion to Contact Lenses

PubMed Central

Dutta, Debarun; Willcox, Mark DP

2013-01-01

Adhesion of pathogenic microbes, particularly bacteria, to contact lenses is implicated in contact lens related microbial adverse events. Various in vitro conditions such as type of bacteria, the size of initial inoculum, contact lens material, nutritional content of media, and incubation period can influence bacterial adhesion to contact lenses and the current study investigated the effect of these conditions on bacterial adhesion to contact lenses. There was no significant difference in numbers of bacteria that adhered to hydrogel etafilcon A or silicone hydrogel senofilcon A contact lenses. Pseudomonas aeruginosa adhered in higher numbers compared to Staphylococcus aureus. Within a genera/species, adhesion of different bacterial strains did not differ appreciably. The size of initial inoculum, nutritional content of media, and incubation period played significant roles in bacterial adhesion to lenses. A set of in vitro assay conditions to help standardize adhesion between studies have been recommended. PMID:24833224

28 CFR 552.12 - Close observation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... urine sample is required prior to releasing the inmate from close observation. (2) The light will be kept on at all times. (3) No inmate under close observation status may be allowed to come into contact...

28 CFR 552.12 - Close observation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... urine sample is required prior to releasing the inmate from close observation. (2) The light will be kept on at all times. (3) No inmate under close observation status may be allowed to come into contact...

Closing the brain-to-brain loop in laboratory testing.

PubMed

Plebani, Mario; Lippi, Giuseppe

2011-07-01

Abstract The delivery of laboratory services has been described 40 years ago and defined with the foremost concept of "brain-to-brain turnaround time loop". This concept consists of several processes, including the final step which is the action undertaken on the patient based on laboratory information. Unfortunately, the need for systematic feedback to improve the value of laboratory services has been poorly understood and, even more risky, poorly applied in daily laboratory practice. Currently, major problems arise from the unavailability of consensually accepted quality specifications for the extra-analytical phase of laboratory testing. This, in turn, does not allow clinical laboratories to calculate a budget for the "patient-related total error". The definition and use of the term "total error" refers only to the analytical phase, and should be better defined as "total analytical error" to avoid any confusion and misinterpretation. According to the hierarchical approach to classify strategies to set analytical quality specifications, the "assessment of the effect of analytical performance on specific clinical decision-making" is comprehensively at the top and therefore should be applied as much as possible to address analytical efforts towards effective goals. In addition, an increasing number of laboratories worldwide are adopting risk management strategies such as FMEA, FRACAS, LEAN and Six Sigma since these techniques allow the identification of the most critical steps in the total testing process, and to reduce the patient-related risk of error. As a matter of fact, an increasing number of laboratory professionals recognize the importance of understanding and monitoring any step in the total testing process, including the appropriateness of the test request as well as the appropriate interpretation and utilization of test results.

Does Closeness to Someone Who Is Gay, Lesbian, or Bisexual Influence Etiology Beliefs About Homosexuality?

PubMed

Chonody, Jill M; Kavanagh, Phillip S; Woodford, Michael R

2016-12-01

Research suggests that contact with sexual minorities and etiology beliefs regarding the origins of homosexuality are associated with antigay bias; however, factors related to etiology beliefs have received little empirical attention. Our primary research question is: Does closeness to someone who is gay, lesbian, or bisexual influence etiology beliefs? Students (n = 851) from four U.S. universities completed an anonymous survey, and regression results indicated that contact and closeness were not significantly associated with etiology beliefs. Because both contact and relationship closeness were associated with antigay attitudes, and closeness demonstrated the largest effect, we tested three alternative structural equation models to determine if contact and closeness mediated etiology beliefs. Results suggested that contact and the degree of closeness are indirectly associated with students' etiology beliefs through antigay bias.

Human infection by Brucella melitensis: an outbreak attributed to contact with infected goats.

PubMed

Wallach, J C; Samartino, L E; Efron, A; Baldi, P C

1997-12-01

Although several outbreaks of Brucella melitensis infection have been reported among laboratory workers or goat cheese consumers, outbreaks related to rural labour have been rarely studied. An outbreak of human brucellosis among farm workers of Argentina was studied and revealed a close relationship with an epidemic of caprine abortions which occurred shortly before on the same farm. High rates of B. melitensis infection were found among goats. Active brucellosis was diagnosed in 33 subjects (14 with positive blood culture for B. melitensis), while other 27 did not show evidence of illness. While 25 of the brucellosis active patients were rural workers, only 5 of the healthy subjects were engaged in rural labour. Active brucellosis was diagnosed in 91.3% of the subjects in continuous contact with goats and in 32% of those having an occasional contact with the animals. All the 60 subjects denied consumption of goat cheese or milk. As shown here, epidemic human infections by B. melitensis may develop among people frequently in contact with infected goat herds or goat manure.

Contact versus feeding intoxication by fipronil in Reticulitermes termites (Isoptera: Rhinotermitidae): laboratory evaluation of toxicity, uptake, clearance, and transfer among individuals.

PubMed

Bagnères, A G; Pichon, A; Hope, J; Davis, R W; Clément, J L

2009-02-01

The susceptibility to fipronil of U.S. and French populations of Reticulitermes flavipes (Kollar) (Isoptera: Rhinotermitidae) was evaluated in two types of laboratory bioassays: contact intoxication with 0.01-1 ppm treated sand and feeding intoxication with 0.1-10 ppm treated filter paper. Contact intoxication with 0.01 ppm fipronil caused 60% mortality after 55 and 64 h in the French and U.S. populations, respectively, whereas in the 5 ppm feeding assay 70 and 60% mortality was observed after 7 d in the French and U.S. populations, respectively. We evaluated the uptake, clearance, and transfer of fipronil among workers of French R. flavipes using [14C] fipronil in contact (0.01 ppm) and feeding (3 ppm) bioassays. Fipronil amounts were measured on their cuticle and in their bodies. Maximal uptake was observed in the contact assay. A significant uptake of fipronil occurred in the feeding assay. Transfer from exposed donors to unexposed recipients occurred within 24 h. Frequent horizontal transfer resulted in a significant uptake in recipients, particularly when donor fipronil acquisition was by feeding. Donors transferred approximately 46% of the toxicant to recipients. Social behaviors such as contact and grooming, together with internalization of the biocide, may be components of the horizontal transfer process and contribute to the efficacy of fipronil in the field.

On the structure of contact binaries. I - The contact discontinuity

NASA Technical Reports Server (NTRS)

Shu, F. H.; Lubow, S. H.; Anderson, L.

1976-01-01

The problem of the interior structure of contact binaries is reviewed, and a simple resolution of the difficulties which plague the theory is suggested. It is proposed that contact binaries contain a contact discontinuity between the lower surface of the common envelope and the Roche lobe of the cooler star. This discontinuity is maintained against thermal diffusion by fluid flow, and the transition layer is thin to the extent that the dynamical time scale is short in comparison with the thermal time scale. The idealization that the transition layer has infinitesimal thickness allows a simple formulation of the structure equations which are closed by appropriate jump conditions across the discontinuity. The further imposition of the standard boundary conditions suffices to define a unique model for the system once the chemical composition, the masses of the two stars, and the orbital separation are specified.

EPA National Quality System Contacts

EPA Pesticide Factsheets

Web links and contacts for the individual quality systems developed in support of the EPA Quality System by each EPA Regional Office, National Program Office and ORD National Research Laboratory and Center.

Technical Review of the Laboratory Biosphere Closed Ecological System Facility

NASA Astrophysics Data System (ADS)

Dempster, W.; van Thillo, M.; Alling, A.; Allen, J.; Silverstone, S.; Nelson, M.

The "Laboratory Biosphere", a new closed ecological system facility in Santa Fe, New Mexico (USA) has been constructed and became operational in May 2002. Built and operated by the Global Ecotechnics consortium (Biosphere Technologies and Biosphere Foundation with Biospheric Design Inc., and the Institute of Ecotechnics), the research apparatus for intensive crop growth, biogeochemical cycle dynamics and recycling of inedible crop biomass comprises a sealed cylindrical steel chamber and attached variable volume chamber (lung) to prevent pressures caused by the expansion and contraction of the contained air. The cylindrical growing chamber is 3.7m (12 feet) long and 3.7m (12 foot) diameter, giving an internal volume of 34 m3 (1200 ft 3 ). The two crop growth beds cover 5.5 m2, with a soil depth of 0.3m (12 inches), with 12 x 1000 watt high-pressure sodium lights capable of variable lighting of 40-70 mol per m2 per day. A small soil bed reactor in the chamber can be activated to help with metabolism of chamber trace gases. The volume of the attached variable volume chamber (lung) can range between 0-11 m3 (0-400 ft 3 ). Evapotranspired and soil leachate water are collected, combined and recycled to water the planting beds. Sampling ports enable testing of water quality of leachate, condensate and irrigation water. Visual inspection windows provide views of the entire interior and growing beds. The chamber is also outfitted with an airlock to minimize air exchange when people enter and work in the chamber. Continuous sensors include atmospheric CO2 and oxygen, temperature, humidity, soil moisture, light level and water levels in reservoirs. Both "sniffer" (air ports) and "sipper" (water ports) will enable collection of water or air samples for detailed analysis. This paper reports on the development of this new soil-based bioregenerative life support closed system apparatus and its technical challenges and capabilities.

The water cycle in closed ecological systems: Perspectives from the Biosphere 2 and Laboratory Biosphere systems

NASA Astrophysics Data System (ADS)

Nelson, Mark; Dempster, W. F.; Allen, J. P.

2009-12-01

To achieve sustainable, healthy closed ecological systems requires solutions to challenges of closing the water cycle - recycling wastewater/irrigation water/soil medium leachate and evaporated water and supplying water of required quality as needed for different needs within the facility. Engineering Biosphere 2, the first multi-biome closed ecological system within a total airtight footprint of 12,700 m 2 with a combined volume of 200,000 m 3 with a total water capacity of some 6 × 10 6 L of water was especially challenging because it included human inhabitants, their agricultural and technical systems, as well as five analogue ecosystems ranging from rainforest to desert, freshwater ecologies to saltwater systems like mangrove and mini-ocean coral reef ecosystems. By contrast, the Laboratory Biosphere - a small (40 m 3 volume) soil-based plant growth facility with a footprint of 15 m 2 - is a very simplified system, but with similar challenges re salinity management and provision of water quality suitable for plant growth. In Biosphere 2, water needs included supplying potable water for people and domestic animals, irrigation water for a wide variety of food crops, and recycling and recovering soil nutrients from wastewater. In the wilderness biomes, providing adequately low salinity freshwater terrestrial ecosystems and maintaining appropriate salinity and pH in aquatic/marine ecosystems were challenges. The largest reservoirs in Biosphere 2 were the ocean/marsh with some 4 × 10 6 L, soil with 1 to 2 × 10 6 l, primary storage tank with 0 to 8 × 10 5 L and storage tanks for condensate and soil leachate collection and mixing tanks with a capacity of 1.6 × 10 5 L to supply irrigation for farm and wilderness ecosystems. Other reservoirs were far smaller - humidity in the atmosphere (2 × 10 3 L), streams in the rainforest and savannah, and seasonal pools in the desert were orders of magnitude smaller (8 × 10 4 L). Key technologies included condensation from

EXPERIMENTS ON SLIP DAMPING AT ROUNDED CONTACTS

DTIC Science & Technology

SLIDING CONTACTS, *STAINLESS STEEL, DAMPING, ELASTIC PROPERTIES, FRICTION, LABORATORY EQUIPMENT, LOAD DISTRIBUTION , MANAGEMENT ENGINEERING, MEASUREMENT, OSCILLOSCOPES, SHEAR STRESSES, SPHERES, SURFACES, THEORY

46 CFR 190.15-10 - Ventilation for closed spaces.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Ventilation for closed spaces. 190.15-10 Section 190.15... CONSTRUCTION AND ARRANGEMENT Ventilation § 190.15-10 Ventilation for closed spaces. (a) All enclosed spaces... chemical laboratories, scientific laboratories, chemical storerooms, and machinery spaces and for closing...

46 CFR 190.15-10 - Ventilation for closed spaces.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Ventilation for closed spaces. 190.15-10 Section 190.15... CONSTRUCTION AND ARRANGEMENT Ventilation § 190.15-10 Ventilation for closed spaces. (a) All enclosed spaces... chemical laboratories, scientific laboratories, chemical storerooms, and machinery spaces and for closing...

46 CFR 190.15-10 - Ventilation for closed spaces.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Ventilation for closed spaces. 190.15-10 Section 190.15... CONSTRUCTION AND ARRANGEMENT Ventilation § 190.15-10 Ventilation for closed spaces. (a) All enclosed spaces... chemical laboratories, scientific laboratories, chemical storerooms, and machinery spaces and for closing...

46 CFR 190.15-10 - Ventilation for closed spaces.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Ventilation for closed spaces. 190.15-10 Section 190.15... CONSTRUCTION AND ARRANGEMENT Ventilation § 190.15-10 Ventilation for closed spaces. (a) All enclosed spaces... chemical laboratories, scientific laboratories, chemical storerooms, and machinery spaces and for closing...

46 CFR 190.15-10 - Ventilation for closed spaces.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ventilation for closed spaces. 190.15-10 Section 190.15... CONSTRUCTION AND ARRANGEMENT Ventilation § 190.15-10 Ventilation for closed spaces. (a) All enclosed spaces... chemical laboratories, scientific laboratories, chemical storerooms, and machinery spaces and for closing...

Investigation of household contacts of pulmonary tuberculosis patients increases case detection in Mwanza City, Tanzania.

PubMed

Beyanga, Medard; Kidenya, Benson R; Gerwing-Adima, Lisa; Ochodo, Eleanor; Mshana, Stephen E; Kasang, Christa

2018-03-06

Tuberculosis (TB) contact tracing is a key strategy for containing TB and provides addition to the passive case finding approach. However, this practice has not been implemented in Tanzania, where there is unacceptably high treatment gap of 62.1% between cases estimated and cases detected. Therefore calls for more aggressive case finding for TB to close this gap. We aimed to determine the magnitude and predictors of bacteriologically-confirmed pulmonary TB among household contacts of bacteriologically-confirmed pulmonary TB index cases in the city of Mwanza, Tanzania. This study was carried out from August to December 2016 in Mwanza city at the TB outpatient clinics of Tertiary Hospital of the Bugando Medical Centre, Sekou-Toure Regional Hospital, and Nyamagana District Hospital. Bacteriologically-confirmed TB index cases diagnosed between May and July 2016 were identified from the laboratory registers book. Contacts were traced by home visits by study TB nurses, and data were collected using a standardized TB screening questionnaire. To detect the bacterioriologically-confirmed pulmonary TB, two sputum samples per household contact were collected under supervision for all household contacts following standard operating procedures. Samples were transported to the Bugando Medical Centre TB laboratory for investigation for TB using fluorescent smear microscopy, GeneXpert MTB/RIF and Löwenstein-Jensen (LJ) culture. Logistic regression was used to determine predictors of bacteriologically-confirmed pulmonary TB among household contacts. During the study period, 456 household contacts from 93 TB index cases were identified. Among these 456 household contacts, 13 (2.9%) were GeneXpert MTB/RIF positive, 18 (3.9%) were MTB-culture positive and four (0.9%) were AFB-smear positive. Overall, 29 (6.4%) of contacts had bacteriologically-confirmed pulmonary TB. Predictors of bacteriologically-confirmed pulmonary TB among household contacts were7being married (Odds ratio [OR

Close Contact Casting vs Surgery for Initial Treatment of Unstable Ankle Fractures in Older Adults: A Randomized Clinical Trial.

PubMed

Willett, Keith; Keene, David J; Mistry, Dipesh; Nam, Julian; Tutton, Elizabeth; Handley, Robert; Morgan, Lesley; Roberts, Emma; Briggs, Andrew; Lall, Ranjit; Chesser, Timothy J S; Pallister, Ian; Lamb, Sarah E

2016-10-11

Ankle fractures cause substantial morbidity in older persons. Surgical fixation is the contemporary intervention but is associated with infection and other healing complications. To determine whether initial fracture treatment with close contact casting, a molded below-knee cast with minimal padding, offers outcome equivalent to that with immediate surgery, with fewer complications and less health resource use. This was a pragmatic, equivalence, randomized clinical trial with blinded outcome assessors. A pilot study commenced in May 2004, followed by multicenter recruitment from July 2010 to November 2013; follow-up was completed May 2014. Recruitment was from 24 UK major trauma centers and general hospitals. Participants were 620 adults older than 60 years with acute, overtly unstable ankle fracture. Exclusions were serious limb or concomitant disease or substantial cognitive impairment. Participants were randomly assigned to surgery (n = 309) or casting (n = 311). Casts were applied in the operating room under general or spinal anesthesia by a trained surgeon. The primary 6-month, per-protocol outcome was the Olerud-Molander Ankle Score at 6 months (OMAS; range, 0-100; higher scores indicate better outcomes and fewer symptoms), equivalence prespecified as ±6 points. Secondary outcomes were quality of life, pain, ankle motion, mobility, complications, health resource use, and patient satisfaction. Among 620 adults (mean age, 71 years; 460 [74%] women) who were randomized, 593 (96%) completed the study. Nearly all participants (579/620; 93%) received allocated treatment; 52 of 275 (19%) who initially received casting later converted to surgery, which was allowable in the casting treatment pathway to manage early loss of fracture reduction. At 6 months, casting resulted in ankle function equivalent to that with surgery (OMAS score, 66.0 [95% CI, 63.6-68.5] for surgery vs 64.5 [95% CI, 61.8-67.2] for casting; mean difference, -0.6 [95% CI, -3.9 to 2.6]; P

New Results on Contact Binary Stars

NASA Astrophysics Data System (ADS)

He, J.; Qian, S.; Zhu, L.; Liu, L.; Liao, W.

2014-08-01

Contact binary star is a kind of close binary with the strongest interaction binary system. Their formations and evolutions are unsolved problems in astrophysics. Since 2000, our groups have observed and studied more than half a hundred of contact binaries. In this report, I will summarize our new results of some contact binary stars (e.g. UZ CMi, GSC 03526-01995, FU Dra, GSC 0763-0572, V524 Mon, MR Com, etc.). They are as follow: (1) We discovered that V524 Mon and MR Com are shallow-contact binaries with their period decreasing; (2) GSC 03526-01995 is middle-contact binary without a period increasing or decreasing continuously; (3) UZ CMi, GSC 0763-0572 and FU Dra are middle-contact binaries with the period increasing continuously; (4) UZ CMi, GSC 03526-01995, FU Dra and V524 Mon show period oscillation which may imply the presence of additional components in these contact binaries.

Laboratory Tests

MedlinePlus

... PI CONNECT Research Network USIDNET Patient Registry IDF Survey Research IDF Surveys National Health Insurance Surveys Clinical Trials ... and Fellows Research USIDNET IDF Research Fund IDF Survey Research IDF Surveys Contact Us Search form Search Laboratory ...

Development of a Contact Permeation Test Fixture and Method

DTIC Science & Technology

2013-04-01

direct contact with the skin, indicates the need for a quantitative contact test method. Comparison tests were conducted with VX on a standardized...Guide for the Care and Use of Laboratory Animals (8th ed.; National Research Council: Washington, DC, 2011). This test was also performed in...1 1.2 Development of a Contact-Based Permeation Test Method ........................................ 1 2. EXPERIMENTAL PROCEDURES

The water cycle in closed ecological systems: perspectives from the Biosphere 2 and Laboratory Biosphere systems

NASA Astrophysics Data System (ADS)

Nelson, Mark; Dempster, William; Allen, John P.

To achieve sustainable and healthy closed ecological systems requires successful solutions to the challenge of closing the water cycle - recycling wastewater/soil leachate and evaporateed water and supplying water of required quality as needed for different needs within the facility. Engineering Biosphere 2, the first multi-biome closed ecological system, total footprint of the airtight area is 12,700 m2 with a combined volume of 200,000 m3 with a total water capacity of some 6 x 106 liters of water presented a complex challenge because it included human inhabitants, their agricultural and technical systems, as well as a range of analogue ecosystems ranging from rainforest to desert, freshwater ecologies to mini-ocean coral reef ecosystems. By contrast, the Laboratory Biosphere - a small (40m3 volume) soil-based plant growth facility with a footprint of 15m3 - is a very simplified system, but with some similar issues such as salinity management and the provision of water quality sufficient for plant growth. In Biosphere 2, water needs included supplying potable water for people and domestic animals, irrigation water for a wide variety of food crops, and recycling and recovering soil nutrients from wastewater. In the wilderness biomes, adequately freshwater was needed for terrestrial ecosystems and maintaining appropriate salinity and pH in aquatic/marine ecosystems. The largest reservoirs in Biosphere 2 were the ocean/marsh with some 4x106 liters, soil with 2 x 106 liters, primary storage tanks with a capacity for up to 8 x 105 liters and storage tanks for condensate collection and mixing tanks with 1.5 x 105 liters to supply irrigation for farm and wilderness ecosystems. Other reservoirs were far smaller - humidity in the atmosphere (2 x 103 liters), streams in the rainforest and savannah, and seasonal pools in the desert were orders of magnitude smaller (8 x 103 liters). Key technologies included condensation from humidity in the airhandlers and from the glass

Contact Us | Frederick National Laboratory for Cancer Research

Cancer.gov

E-mail:fnlwebsite@nih.gov Phone:(301) 846-1000 Postal Mail: Frederick National Laboratory for Cancer Research P.O. Box B Frederick, MD 21702-1201 Human Resources Office of Recruitment (301) 846-5362 Jim

An approximate JKR solution for a general contact, including rough contacts

NASA Astrophysics Data System (ADS)

Ciavarella, M.

2018-05-01

In the present note, we suggest a simple closed form approximate solution to the adhesive contact problem under the so-called JKR regime. The derivation is based on generalizing the original JKR energetic derivation assuming calculation of the strain energy in adhesiveless contact, and unloading at constant contact area. The underlying assumption is that the contact area distributions are the same as under adhesiveless conditions (for an appropriately increased normal load), so that in general the stress intensity factors will not be exactly equal at all contact edges. The solution is simply that the indentation is δ =δ1 -√{ 2 wA‧ /P″ } where w is surface energy, δ1 is the adhesiveless indentation, A‧ is the first derivative of contact area and P‧‧ the second derivative of the load with respect to δ1. The solution only requires macroscopic quantities, and not very elaborate local distributions, and is exact in many configurations like axisymmetric contacts, but also sinusoidal waves contact and correctly predicts some features of an ideal asperity model used as a test case and not as a real description of a rough contact problem. The solution permits therefore an estimate of the full solution for elastic rough solids with Gaussian multiple scales of roughness, which so far was lacking, using known adhesiveless simple results. The result turns out to depend only on rms amplitude and slopes of the surface, and as in the fractal limit, slopes would grow without limit, tends to the adhesiveless result - although in this limit the JKR model is inappropriate. The solution would also go to adhesiveless result for large rms amplitude of roughness hrms, irrespective of the small scale details, and in agreement with common sense, well known experiments and previous models by the author.

Contact Us | Center for Cancer Research

Cancer.gov

Program Contact Program Manager Anuradha Budhu, Ph.D. Program Manager, NCI CCR Liver Cancer Program Senior Associate Scientist, Liver Carcinogenesis Section Laboratory of Human Carcinogenesis NCI Center for Cancer Research Tel: 240-760-6837

Contact Dermatitis for the Practicing Allergist.

PubMed

Bernstein, David I

2015-01-01

This article provides an overview of important practice recommendations from the recently updated Contact Dermatitis Practice Parameter. This updated parameter provides essential recommendations pertaining to clinical history, physical examination, and patch testing evaluation of patients suspected of allergic contact dermatitis. In addition to providing guidance for performing and interpreting closed patch testing, the updated parameter provides concrete recommendations for assessing metal hypersensitivity in patients receiving prosthetic devices, for evaluating workers with occupational contact dermatitis, and also for addressing allergic contact dermatitis in children. Finally, the document provides practical recommendations useful for educating patients regarding avoidance of exposure to known contact sensitizers in the home and at work. The Contact Dermatitis Parameter is designed as a practical, evidence-based clinical tool to be used by allergists and dermatologists who routinely are called upon to evaluate patients with skin disorders. Copyright © 2015 American Academy of Allergy, Asthma & Immunology. Published by Elsevier Inc. All rights reserved.

Sandia National Laboratories: News: Media Resources: Media Contacts

Science.gov Websites

Programs Nuclear Weapons About Nuclear Weapons Safety & Security Weapons Science & Technology Robotics R&D 100 Awards Laboratory Directed Research & Development Technology Deployment Centers Audit Sandia's Economic Impact Licensing & Technology Transfer Browse Technology Portfolios

Elastic contact mechanics: percolation of the contact area and fluid squeeze-out.

PubMed

Persson, B N J; Prodanov, N; Krick, B A; Rodriguez, N; Mulakaluri, N; Sawyer, W G; Mangiagalli, P

2012-01-01

The dynamics of fluid flow at the interface between elastic solids with rough surfaces depends sensitively on the area of real contact, in particular close to the percolation threshold, where an irregular network of narrow flow channels prevails. In this paper, numerical simulation and experimental results for the contact between elastic solids with isotropic and anisotropic surface roughness are compared with the predictions of a theory based on the Persson contact mechanics theory and the Bruggeman effective medium theory. The theory predictions are in good agreement with the experimental and numerical simulation results and the (small) deviation can be understood as a finite-size effect. The fluid squeeze-out at the interface between elastic solids with randomly rough surfaces is studied. We present results for such high contact pressures that the area of real contact percolates, giving rise to sealed-off domains with pressurized fluid at the interface. The theoretical predictions are compared to experimental data for a simple model system (a rubber block squeezed against a flat glass plate), and for prefilled syringes, where the rubber plunger stopper is lubricated by a high-viscosity silicon oil to ensure functionality of the delivery device. For the latter system we compare the breakloose (or static) friction, as a function of the time of stationary contact, to the theory prediction.

50 CFR 648.73 - Closed areas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... degradation. Certain areas are closed to all surf clam and ocean quahog fishing because of adverse... safe for human consumption. For information regarding these areas contact the State of Maine Division...

Class Racial Composition, the Friendliness of Interracial Contact and Student Performance.

ERIC Educational Resources Information Center

Patchen, Martin; And Others

This paper presents further evidence bearing on the hypothesis that the academic performance of students is associated more closely with the friendliness or unfriendliness of interracial contact than with the sheer opportunity for interracial contact. In addition, evidence is presented concerning the relationship of interracial contact and of…

Evaluation of a bioluminescence method, contact angle measurements and topography for testing the cleanability of plastic surfaces under laboratory conditions

NASA Astrophysics Data System (ADS)

Redsven, I.; Kymäläinen, H.-R.; Pesonen-Leinonen, E.; Kuisma, R.; Ojala-Paloposki, T.; Hautala, M.; Sjöberg, A.-M.

2007-04-01

Detection of adenosine triphosphate (ATP) by bioluminescence is used, for instance, in the food industry and in hospitals to assess the hygiene status of surfaces. The aim of this laboratory study was to investigate the feasibility of the ATP method for estimating the cleanability of resilient floor coverings from biological soil. The surfaces were worn using a Soiling and Wearing Drum Tester, and soiled and cleaned with an Erichsen Washability and Scrubbing Resistance Tester. In the laboratory test carried out with the bioluminescence method, most of the new and worn floor coverings that were biologically soiled were cleaned efficiently. According to this study, the semiquantitative ATP screening method can be used for hygiene monitoring of flooring materials. No correlation was found between cleanability and contact angles or surface topography measured using a profilometer. However, by revealing local irregularities and damage on surfaces, scanning electron micrographs appeared useful in explaining differences in cleanability.

76 FR 60946 - Post Office Closing

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-30

.../filing-online/login.aspx . Commenters who cannot submit their views electronically should contact the... determination to close the North Canton post office in North Canton, Connecticut. The petition was filed by Ray...

Controlled laboratory testing of arthroscopic shaver systems: do blades, contact pressure, and speed influence their performance?

PubMed

Wieser, Karl; Erschbamer, Matthias; Neuhofer, Stefan; Ek, Eugene T; Gerber, Christian; Meyer, Dominik C

2012-10-01

The purposes of this study were (1) to establish a reproducible, standardized testing protocol to evaluate the performance of different shaver systems and blades in a controlled, laboratory setting, and (2) to determine the optimal use of different blades with respect to the influence of contact pressure and speed of blade rotation. A holding device was developed for reproducible testing of soft-tissue (tendon and meniscal) resection performance in a submerged environment, after loading of the shaver with interchangeable weights. The Karl Storz Powershaver S2 (Karl Storz, Tuttlingen, Germany), the Stryker Power Shaver System (Stryker, Kalamazoo, MI), and the Dyonics Power Shaver System (Smith & Nephew, Andover, MA) were tested, with different 5.5-mm shaver blades and varied contact pressure and rotation speed. For quality testing, serrated shaver blades were evaluated at 40× image magnification. Overall, more than 150 test cycles were performed. No significant differences could be detected between comparable blade types from different manufacturers. Shavers with a serrated inner blade and smooth outer blade performed significantly better than the standard smooth resectors (P < .001). Teeth on the outer layer of the blade did not lead to any further improvement of resection (P = .482). Optimal contact pressure ranged between 6 and 8 N, and optimal speed was found to be 2,000 to 2,500 rpm. Minimal blunting of the shaver blades occurred after soft-tissue resection; however, with bone resection, progressive blunting of the shaver blades was observed. Arthroscopic shavers can be tested in a controlled setting. The performance of the tested shaver types appears to be fairly independent of the manufacturer. For tendon resection, a smooth outer blade and serrated inner blade were optimal. This is one of the first established independent and quantitative assessments of arthroscopic shaver systems and blades. We believe that this study will assist the surgeon in choosing

Lack of observed association between armadillo contact and leprosy in humans.

PubMed

Filice, G A; Greenberg, R N; Fraser, D W

1977-01-01

In 1971 it was discovered that the nine-banded armadillo (Dasypus novemcinctus) could be infected in the laboratory with Mycobacterium leprae, and would manifest disease similar to the lepromatous form of leprosy in man. In 1975 several wild armadillos captured in Louisiana were found to have a disease identical to the M. laprae infection in laboratory animals. To determine if there is a significant association between contact with armadillos and presence of leprosy in humans, the armadillo contact of persons with indigenous leprosy in Louisiana was compared to the contact of matched controls. No difference in the nature or frequency of contact was found. If this infection of wild armadillos is of recent onset, an association with human leprosy in enzootic areas may not be detectable for several years.

76 FR 35453 - Center for Scientific Review; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-17

... Laboratory, 9700 S. Cass Avenue, Argonne, IL 60439. Contact Person: James W. Mack, PhD, Scientific Review...: National Institutes of Health, 6701 Rockledge Drive, Bethesda, MD 20892 (Virtual Meeting). Contact Person...

Age- and Sex-Specific Social Contact Patterns and Incidence of Mycobacterium tuberculosis Infection.

PubMed

Dodd, Peter J; Looker, Clare; Plumb, Ian D; Bond, Virginia; Schaap, Ab; Shanaube, Kwame; Muyoyeta, Monde; Vynnycky, Emilia; Godfrey-Faussett, Peter; Corbett, Elizabeth L; Beyers, Nulda; Ayles, Helen; White, Richard G

2016-01-15

We aimed to model the incidence of infection with Mycobacterium tuberculosis among adults using data on infection incidence in children, disease prevalence in adults, and social contact patterns. We conducted a cross-sectional face-to-face survey of adults in 2011, enumerating "close" (shared conversation) and "casual" (shared indoor space) social contacts in 16 Zambian communities and 8 South African communities. We modeled the incidence of M. tuberculosis infection in all age groups using these contact patterns, as well as the observed incidence of M. tuberculosis infection in children and the prevalence of tuberculosis disease in adults. A total of 3,528 adults participated in the study. The reported rates of close and casual contact were 4.9 per adult per day (95% confidence interval: 4.6, 5.2) and 10.4 per adult per day (95% confidence interval: 9.3, 11.6), respectively. Rates of close contact were higher for adults in larger households and rural areas. There was preferential mixing of close contacts within age groups and within sexes. The estimated incidence of M. tuberculosis infection in adults was 1.5-6 times higher (2.5%-10% per year) than that in children. More than 50% of infections in men, women, and children were estimated to be due to contact with adult men. We conclude that estimates of infection incidence based on surveys in children might underestimate incidence in adults. Most infections may be due to contact with adult men. Treatment and control of tuberculosis in men is critical to protecting men, women, and children from tuberculosis. © The Author 2015. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health.

Contact Inhibition: Also a Control for Cell Proliferation in Unicellular Algae?

PubMed

Costas, E; Aguilera, A; Gonzalez-Gil, S; López-Rodas, V

1993-02-01

According to traditional views, the proliferation of unicellular algae is controlled primarily by environmental conditions. But as in mammalian cells, other biological mechanisms, such as growth factors, cellular aging, and contact inhibition, might also control algal proliferation. Here we ask whether contact inhibition regulates growth in several species of unicellular algae as it does in mammalian cells. Laboratory cultures of the dinoflagellate Prorocentrum lima (Ehrenberg) Dodge show contact inhibition at low cell density, so this would be an autocontrol mechanism of cell proliferation that could also act in natural populations of P. lima. But, Synechocystis spp., Phaeodactylum tricornutum (Bohlin), Skeletonema costatum (Greville), and Tetraselmis spp. do not exhibit contact inhibition in laboratory cultures because they are able to grow at high cellular density. Apparently their growth is limited by nutrient depletion or catabolite accumulation instead of contact inhibition. Spirogyra insignis (Hassall) Kutz, Prorocentrum triestinum Schiller, and Alexandrium tamarense (Halim) Balech show a complex response, as they are able to grow in both low and high cell density medium. These results suggest that contact inhibition is more adaptative in benthic unicellular algae.

7 CFR 58.731 - Closing and sealing containers.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Closing and sealing containers. 58.731 Section 58.731... Procedures § 58.731 Closing and sealing containers. Pouches, liners, or containers having product contact... means, so as to assure against contamination. Each container in addition to other required labeling...

Closed-Tube Barcoding.

PubMed

Sirianni, Nicky M; Yuan, Huijun; Rice, John E; Kaufman, Ronit S; Deng, John; Fulton, Chandler; Wangh, Lawrence J

2016-11-01

Here, we present a new approach for increasing the rate and lowering the cost of identifying, cataloging, and monitoring global biodiversity. These advances, which we call Closed-Tube Barcoding, are one application of a suite of proven PCR-based technologies invented in our laboratory. Closed-Tube Barcoding builds on and aims to enhance the profoundly important efforts of the International Barcode of Life initiative. Closed-Tube Barcoding promises to be particularly useful when large numbers of small or rare specimens need to be screened and characterized at an affordable price. This approach is also well suited for automation and for use in portable devices.

Contact tracing the first Middle East respiratory syndrome case in the Philippines, February 2015.

PubMed

Racelis, Sheryl; de los Reyes, Vikki Carr; Sucaldito, Ma Nemia; Deveraturda, Imelda; Roca, John Bobbie; Tayag, Enrique

2015-01-01

Middle East respiratory syndrome (MERS) is an illness caused by a coronavirus in which infected persons develop severe acute respiratory illness. A person can be infected through close contacts. This is an outbreak investigation report of the first confirmed MERS case in the Philippines and the subsequent contact tracing activities. Review of patient records and interviews with health-care personnel were done. Patient and close contacts were tested for MERS-coronavirus (CoV) by real time-polymerase chain reaction. Close contacts were identified and categorized. All traced contacts were monitored daily for appearance of illness for 14 days starting from the date of last known exposure to the confirmed case. A standard log sheet was used for symptom monitoring. The case was a 31-year-old female who was a health-care worker in Saudi Arabia. She had mild acute respiratory illness five days before travelling to the Philippines. On 1 February, she travelled with her husband to the Philippines while she had a fever. On 2 February, she attended a health facility in the Philippines. On 8 February, respiratory samples were tested for MERS-CoV and yielded positive results. A total of 449 close contacts were identified, and 297 (66%) were traced. Of those traced, 15 developed respiratory symptoms. All of them tested negative for MERS. In this outbreak investigation, the participation of health-care personnel in conducting vigorous contact tracing may have reduced the risk of transmission. However, being overly cautious to include more contacts for the outbreak response should be further reconsidered.

Control of peptide nanotube diameter by chemical modifications of an aromatic residue involved in a single close contact

PubMed Central

Tarabout, Christophe; Roux, Stéphane; Gobeaux, Frédéric; Fay, Nicolas; Pouget, Emilie; Meriadec, Cristelle; Ligeti, Melinda; Thomas, Daniel; IJsselstijn, Maarten; Besselievre, François; Buisson, David-Alexandre; Verbavatz, Jean-Marc; Petitjean, Michel; Valéry, Céline; Perrin, Lionel; Rousseau, Bernard; Artzner, Franck; Paternostre, Maité; Cintrat, Jean-Christophe

2011-01-01

Supramolecular self-assembly is an attractive pathway for bottom-up synthesis of novel nanomaterials. In particular, this approach allows the spontaneous formation of structures of well-defined shapes and monodisperse characteristic sizes. Because nanotechnology mainly relies on size-dependent physical phenomena, the control of monodispersity is required, but the possibility of tuning the size is also essential. For self-assembling systems, shape, size, and monodispersity are mainly settled by the chemical structure of the building block. Attempts to change the size notably by chemical modification usually end up with the loss of self-assembly. Here, we generated a library of 17 peptides forming nanotubes of monodisperse diameter ranging from 10 to 36 nm. A structural model taking into account close contacts explains how a modification of a few Å of a single aromatic residue induces a fourfold increase in nanotube diameter. The application of such a strategy is demonstrated by the formation of silica nanotubes of various diameters. PMID:21518895

Seroprevalence of SARS coronavirus antibody in household contacts.

PubMed Central

Lee, C-C; Chen, S-Y; Chang, I-J; Tsai, P-C; Lu, T-C; Wu, P-L; Chen, W-J; Huang, L-M; Chang, S-C

2005-01-01

Between March and July 2003, 671 cases of severe acute respiratory syndrome (SARS) were diagnosed in Taiwan with a total of 84 fatalities. After the epidemic, a serological survey was conducted involving the asymptomatic household contacts. Household contacts of 13 index patients were enrolled in the study. Contact history and clinical symptoms of the household contacts were recorded by standardized questionnaires. Blood samples of patients and household contacts were collected at least 28 days after symptom onset in the index patients or household exposure in the contacts for SARS-associated coronavirus (SARS-CoV) IgG testing. On the basis of this investigation, 29 persons (25 adults and 4 children) were identified as having had unprotected exposure to the index cases before infection-control practices were implemented. Laboratory evaluation of clinical specimens showed no evidence of transmission of SARS-CoV infection to any contacts. This investigation demonstrated that subclinical transmission among household contacts was low in the described setting. PMID:16274510

Management of Contacts of Patients With Severe Invasive Group A Streptococcal Infection.

PubMed

de Almeida Torres, Rosângela Stadnick Lauth; dos Santos, Talita Zajac; Torres, Robson Antônio de Almeida; Petrini, Lygia Maria Coimbra de Manuel; Burger, Marion; Steer, Andrew C; Smeesters, Pierre R

2016-03-01

Conflicting recommendations regarding antibiotic prophylaxis for contacts of patients with invasive group A streptococcal (GAS) infection exist. Close contacts of patients with such severe and rapidly progressive disease often strongly appeal to the treating clinicians for antimicrobial treatment to prevent additional cases. We aimed to use an approach based on pharyngeal culture testing of contacts and targeted antibiotic prophylaxis. A large throat swab survey including 105 contacts was undertaken after a fulminant and fatal case of GAS necrotizing fasciitis. GAS strains were characterized by emm typing and antimicrobial susceptibility to 7 antibiotics. The presence of 30 virulence determinants was determined by polymerase chain reaction and sequencing. The GAS isolate recovered from the index patient was an M1T1 GAS clone susceptible to all antimicrobial agents tested. The same clone was present in the throat of 36% of close contacts who had exposure to the index patient (family households and classroom contacts) for >24 hours/week, whereas the strain was present in only 2% of the other contacts. Although the study does not allow firm conclusions to be drawn as to whether antibiotic prophylaxis is effective, we describe a practical approach, including an educational campaign and targeted antibiotic treatment to close contacts who have been exposed to an index patient for > 24 hours/week before the initial disease onset. © The Author 2014. Published by Oxford University Press on behalf of the Pediatric Infectious Diseases Society. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact Running-in Process

DTIC Science & Technology

2015-10-01

ARL-TR-7501 ● OCT 2015 US Army Research Laboratory Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact...Research Laboratory Friction Mapping as a Tool for Measuring the Elastohydrodynamic Contact Running-in Process by Stephen Berkebile Vehicle...YYYY) October 2015 2. REPORT TYPE Final 3. DATES COVERED (From - To) 1 January–30 June 2015 4. TITLE AND SUBTITLE Friction Mapping as a Tool for

Novel laboratory approaches to multi-purpose aquatic bioregenerative closed-loop food production systems

NASA Astrophysics Data System (ADS)

Blüm, V.; Andriske, M.; Kreuzberg, K.; Paassen, U.; Schreibman, M. P.; Voeste, D.

Based on the construction principle of the Closed Equilibrated Biological Aquatic System (C.E.B.A.S.) two novel combined animal-plant production systems were developed in laboratory scale the first of which is dedicated to mid-term operation in closed state up to two years. In principle both consist of the "classic" C.E.B.A.S. subcomponents: animal tank (Zoological Component), plant cultivators (Botanical Component), ammonia converting bacteria filter (Microbial Component) and data acquisition/control unit (Electronical Component). The innovative approach in the first system is the utilization of minimally three aquatic plant cultivators for different species. In this one the animal tank has a volume of about 160 liters and is constructed as an "endless-way system" surronding a central unit containing the heat exchanger and the bacteria filter with volumes of about 1.5 liters each. A suspension plant cultivator (1 liter) for the edible duckweed Wolffia arrhiza is externally connected. The second plant cultivator is a meandric microalgal bioreactor for filamentous green algae. The third plant growth facilitiy is a chamber with about 2.5 liters volume for cultivation of the "traditional" C.E.B.A.S. plant species, the rootless buoyant Ceratophyllum demersum. Both latter units are illuminated with 9 W fluorescent lamps. In the current experiment the animal tank contains the live-bearing teleost fish Xiphophorus helleri and the small pulmonate water snail Biomphalaria glabrata because their physiological adaptation to the closed system conditions is well known from many previous C.E.B.A.S. experiments. The water temperature is maintained at 25 °C and the oxygen level is regulated between 4 and 7 mg/1 by switching on and off the plant cultivator illuminations according to a suitable pattern thus utilizing solely the oxygen produced by photosynthesis. The animals and the micoorganisms of filter and bioflim provide the plants with a sufficient amount of carbon dioxide

Novel laboratory approaches to multi-purpose aquatic bioregenerative closed-loop food production systems.

PubMed

Blum, V; Andriske, M; Kreuzberg, K; Paassen, U; Schreibman, M P; Voeste, D

1998-01-01

Based on the construction principle of the Closed Equilibrated Biological Aquatic System (C.E.B.A.S.) two novel combined animal-plant production systems were developed in laboratory scale the first of which is dedicated to mid-term operation in closed state up to two years. In principle both consist of the "classic" C.E.B.A.S. subcomponents: animal tank (Zoological Component), plant cultivators (Botanical Component), ammonia converting bacteria filter (Microbial Component) and data acquisition/control unit (Electronical Component). The innovative approach in the first system is the utilization of minimally three aquatic plant cultivators for different species. In this one the animal tank has a volume of about 160 liters and is constructed as an "endless-way system" surrounding a central unit containing the heat exchanger and the bacteria filter with volumes of about 1.5 liters each. A suspension plant cultivator (1 liter) for the edible duckweed Wolffia arrhiza is externally connected. The second plant cultivator is a meandric microalgal bioreactor for filamentous green algae. The third plant growth facility is a chamber with about 2.5 liters volume for cultivation of the "traditional" C.E.B.A.S. plant species, the rootless buoyant Ceratophyllum demersum. Both latter units are illuminated with 9 W fluorescent lamps. In the current experiment the animal tank contains the live-bearing teleost fish Xiphophorus helleri and the small pulmonate water snail Biomphalaria glabrata because their physiological adaptation to the closed system conditions is well known from many previous C.E.B.A.S. experiments. The water temperature is maintained at 25 degrees C and the oxygen level is regulated between 4 and 7 mg/l by switching on and off the plant cultivator illuminations according to a suitable pattern thus utilizing solely the oxygen produced by photosynthesis. The animals and the microorganisms of filter and biofilm provide the plants with a sufficient amount of carbon

Characteristic Processes in Close Peer Friendships of Preterm Infants at Age 12

PubMed Central

Sullivan, Mary C.; Barcelos Winchester, Suzy; Parker, Jeffrey G.; Marks, Amy K.

2012-01-01

Close friendships become important at middle-school age and are unexplored in adolescents born prematurely. The study aimed to characterize friendship behaviors of formerly preterm infants at age 12 and explore similarities and differences between preterm and full-term peers on dyadic friendship types. From the full sample of N = 186, one hundred sixty-six 12-year-old adolescents (40 born full term, 126 born preterm) invited a close friend to a 1.5 hour videotaped laboratory play session. Twenty adolescents were unable to participate due to scheduling conflicts or developmental disability. Characteristic friendship behaviors were identified by Q-sort followed by Q-factoring analysis. Friendship duration, age, and contact differed between the full-term and preterm groups but friendship activities, behaviors, and quality were similar despite school service use. Three Q-factors, leadership, distancing, and mutual playfulness, were most characteristic of all dyads, regardless of prematurity. These prospective, longitudinal findings demonstrate diminished prematurity effects at adolescence in peer friendship behavior and reveal interpersonal dyadic processes that are important to peer group affiliation and other areas of competence. PMID:23308346

Nickel Silicide Metallization for Passivated Tunneling Contacts for Silicon Solar Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, Alexander; Florent, Karine; Tapriya, Astha

Passivated tunneling contacts offer promise for applications in Interdigitated Back Passivated Contact (IBPC) high efficiency silicon solar cells. Metallization of these contacts remains a key research topic. This paper investigates NiSi/poly-Si/SiO2/c-Si passivated contacts using photoluminescence and contact resistivity measurements. An amorphous Si interlayer between the NiSi and poly-Si is observed to improve passivation, decreasing recombination. The overall recombination loss has a linear trend with the NiSi thickness. Implied Voc values close to 700 mV and contact resistivities below 10 mohm-cm2 have been achieved in NiSi/poly-Si:P/SiO2/c-Si contacts.

Contact lens-induced circumlimbal staining in silicone hydrogel contact lenses worn on a daily wear basis.

PubMed

Maïssa, Cécile; Guillon, Michel; Garofalo, Renee J

2012-01-01

The principal objective of the study was to measure the conjunctival staining produced in the circumlimbal region by silicone hydrogel contact lenses with different edge designs. The secondary objective was to investigate the association between circumlimbal staining and comfort. Four silicone hydrogel contact lenses: ACUVUE OASYS (knife edge design), AIR OPTIX, Biofinity (chisel edge rounded edge combination), and PureVision (rounded edge design), and 1 hydrogel contact lens, ACUVUE 2 (knife edge design), were tested. The study was conducted on a cohort population of 27 established soft contact lens wearers, who wore each contact lens type, in a random order, for a period of 10 (±2) days. Circumlimbal staining was measured in a double-masked fashion through image analysis of digital photographs of lissamine green taken under controlled experimental conditions. The results obtained showed that contact lens edge design was the primary factor controlling circumlimbal staining for silicone hydrogel lenses: a rounded edge away from the ocular surface produced the lowest staining (average, 0.19%) and a knife edge in close apposition to the ocular surface produced the highest staining (average, 1.34%). Contact lens material rigidity was also identified to affect circumlimbal staining and an inverse association between circumlimbal staining and contact lens comfort was demonstrated: the rounded edge design produced the lowest comfort (72 of 100) and the knife edge design produced the highest (87 out of 100). Soft contact lens wear induces circumlimbal staining, the level of staining being influenced by the contact lens edge design. However, high level of circumlimbal staining is not associated with decreased comfort.

Closed cycle ion exchange method for regenerating acids, bases and salts

DOEpatents

Dreyfuss, Robert M.

1976-01-01

A method for conducting a chemical reaction in acidic, basic, or neutral solution as required and then regenerating the acid, base, or salt by means of ion exchange in a closed cycle reaction sequence which comprises contacting the spent acid, base, or salt with an ion exchanger, preferably a synthetic organic ion-exchange resin, so selected that the counter ions thereof are ions also produced as a by-product in the closed reaction cycle, and then regenerating the spent ion exchanger by contact with the by-product counter ions. The method is particularly applicable to closed cycle processes for the thermochemical production of hydrogen.

Differential Dynamics of Platelet Contact and Spreading

PubMed Central

Lee, Dooyoung; Fong, Karen P.; King, Michael R.; Brass, Lawrence F.; Hammer, Daniel A.

2012-01-01

Platelet spreading is critical for hemostatic plug formation and thrombosis. However, the detailed dynamics of platelet spreading as a function of receptor-ligand adhesive interactions has not been thoroughly investigated. Using reflection interference contrast microscopy, we found that both adhesive interactions and PAR4 activation affect the dynamics of platelet membrane contact formation during spreading. The initial growth of close contact area during spreading was controlled by the combination of different immobilized ligands or PAR4 activation on fibrinogen, whereas the growth of the total area of spreading was independent of adhesion type and PAR4 signaling. We found that filopodia extend to their maximal length and then contract over time; and that filopodial protrusion and expansion were affected by PAR4 signaling. Upon PAR4 activation, the integrin αIIbβ3 mediated close contact to fibrinogen substrata and led to the formation of ringlike patterns in the platelet contact zone. A systematic study of platelet spreading of GPVI-, α2-, or β3-deficient platelets on collagen or fibrinogen suggests the integrin α2 is indispensable for spreading on collagen. The platelet collagen receptors GPVI and α2 regulate integrin αIIbβ3-mediated platelet spreading on fibrinogen. This work elucidates quantitatively how receptor-ligand adhesion and biochemical signals synergistically control platelet spreading. PMID:22325269

The risk of capsular breakage from phacoemulsification needle contact with the lens capsule: a laboratory study.

PubMed

Meyer, Jay J; Kuo, Annie F; Olson, Randall J

2010-06-01

To determine capsular breakage risk from contact by phacoemulsification needles by machine and tip type. Experimental laboratory investigation. Infiniti (Alcon, Inc.) with Intrepid cartridges and Signature (Abbott Medical Optics, Inc.) phacoemulsification machines were tested using 19- and 20-gauge sharp and rounded tips. Actual and unoccluded flow vacuum were determined at 550 mm Hg, bottle height of 75 cm, and machine-indicated flow rate of 60 mL/minute. Breakage from brief tip contact with a capsular surrogate and human cadaveric lenses was calculated. Nineteen-gauge tips had more flow and less unoccluded flow vacuum than 20-gauge tips for both machines, with highest unoccluded flow vacuum in the Infiniti. The 19-gauge sharp tip was more likely than the 20-gauge sharp tip to cause surrogate breakage for Signature with micropulse and Ellips (Abbott Medical Optics, Inc.) ultrasound at 100% power. For Infiniti using OZil (Alcon, Inc.) ultrasound, 20-gauge sharp tips were more likely than 19-gauge sharp tips to break the membrane. For cadaveric lenses, using rounded 20-gauge tips at 100% power, breakage rates were micropulse (2.3%), Ellips (2.3%), OZil (5.3%). Breakage rates for sharp 20-gauge Ellips tips were higher than for rounded tips. Factors influencing capsular breakage may include active vacuum at the tip, flow rate, needle gauge, and sharpness. Nineteen-gauge sharp tips were more likely than 20-gauge tips to cause breakage in lower vacuum methods. For higher-vacuum methods, breakage is more likely with 20-gauge than with 19-gauge tips. Rounded-edge tips are less likely than sharp-edged tips to cause breakage. Copyright 2010 Elsevier Inc. All rights reserved.

Contact stiffness of regularly patterned multi-asperity interfaces

NASA Astrophysics Data System (ADS)

Li, Shen; Yao, Quanzhou; Li, Qunyang; Feng, Xi-Qiao; Gao, Huajian

2018-02-01

Contact stiffness is a fundamental mechanical index of solid surfaces and relevant to a wide range of applications. Although the correlation between contact stiffness, contact size and load has long been explored for single-asperity contacts, our understanding of the contact stiffness of rough interfaces is less clear. In this work, the contact stiffness of hexagonally patterned multi-asperity interfaces is studied using a discrete asperity model. We confirm that the elastic interaction among asperities is critical in determining the mechanical behavior of rough contact interfaces. More importantly, in contrast to the common wisdom that the interplay of asperities is solely dictated by the inter-asperity spacing, we show that the number of asperities in contact (or equivalently, the apparent size of contact) also plays an indispensable role. Based on the theoretical analysis, we propose a new parameter for gauging the closeness of asperities. Our theoretical model is validated by a set of experiments. To facilitate the application of the discrete asperity model, we present a general equation for contact stiffness estimation of regularly rough interfaces, which is further proved to be applicable for interfaces with single-scale random roughness.

Effect of contact ratio on spur gear dynamic load

NASA Technical Reports Server (NTRS)

Liou, Chuen-Huei; Lin, Hsiang Hsi; Oswald, Fred B.; Townsend, Dennis P.

1992-01-01

A computer simulation is presented which shows how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented was performed using the NASA gear dynamics code, DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low contact ratio gears (contact ratio less than 2.0), increasing the contact ratio reduced the gear dynamic load. For high contact ratio gears (contact ratio = or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high contact ratio gears minimized dynamic load better than low contact ratio gears.

Three close binaries in different evolutionary stages in the old open cluster NGC 188

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, L. Y.; Qian, S. B.; Liu, L.

2014-02-01

NGC 188 is a good laboratory for studying the formation and evolution of W UMa type contact binaries due to its rich populations of them. We present a detailed photometric study of three short-period close binaries, EP Cep, ES Cep, and V369 Cep, in the old open cluster NGC 188 based on our two-set photometric observations. We discovered that both EP Cep and ES Cep are shallow-contact binaries with continuously decreasing periods. The difference is in their mass ratios. EP Cep has an extremely low-mass ratio, q = 0.15, while ES Cep has a relatively high-mass ratio, q = 0.69,more » indicating that they lie in different evolutionary stages. ES Cep is likely a newly formed contact binary via a Case A mass transfer, while EP Cep is an evolved system and may be on the oscillations caused by the combined effect of the thermal relaxation oscillation and the variable angular momentum loss. For another system, V369 Cep, we found that it is a primary-filling near-contact binary. Both the semidetached configuration and the continuous decrease in the orbital period indicate that it is undergoing a mass transfer from the primary component to the secondary one. This conclusion is in agreement with the excess luminosity seen in the light curves on the ingress of the secondary minimum produced by the impact of the mass transfer. All of the results suggest that V369 Cep is evolving into contact, and a shallow-contact high-mass ratio system similar to ES Cep will be formed. Then, it will evolve into a low-mass ratio contact binary just like EP Cep, and finally merge into a rapidly rotating single star.« less

NREL Visitors Center Closing Temporarily for Remodeling

Science.gov Websites

Visitors Center Closing Temporarily for Remodeling Media may contact: George Douglas, 303-275-4096 email: George Douglas Golden, Colo., Sept. 6, 2000 - The Visitors Center at the U.S. Department of

The Use of Contact Lenses in Industrial Environments: An Assessment of Current Research and Policy.

ERIC Educational Resources Information Center

Connors, Terry

2001-01-01

Attempts to dispel rumors concerning contact lenses and tries to supply prudent-use practices for allowing contact lenses in industry and laboratories. Discusses federal regulations that impact the use of contact lenses in industry, policy statements from medical organizations on use of contact lenses in industrial environments, and the…

Contact network and satisfaction with contacts in children whose parents have post traumatic stress disorder.

PubMed

Selimbasic, Zihnet; Sinanovic, Osman; Avdibegovic, Esmina; Kravic, Nemina

2009-01-01

The aim was to analyse contacts network and satisfaction with contacts among children of parents with post traumatic stress disorder (PTSD). The sample consisted of 100 pupils (age 10 to 15) from two randomly chosen schools. Children were selected from general population, lived with both parents who have had war traumatic experiences. They agreed to participate in psychometric research. We divided them in two groups: observed (0) group of children (N=50) whose parents were showing symptoms of post traumatic stress disorder (PTSD) and control (C) group of children (N=50) whose parents did not show symptoms of PTSD (evaluated by Harvard trauma questionnaire-BiH version). Contact network was examined by a Map of Contact Network which includes contact and satisfaction with persons in close environment. In relation to gender representatives of fathers and mothers, sample was homogenous. The most important persons in children whose parents are showing symptoms of PTSD were schoolmates (88.0%), home mate (86.0%), mother (72.0%), and father (2.0%). At children whose parents did not show symptoms of PTSD, most important persons were schoolmate (94.0%), mother (80.0%), brother (6.0%), grandfather (8.0%), and father (14.0%). The most distinct disappointment in contacts in children with parents with PTSD symptoms were family, relatives and friends, in school and formal contacts (p < 0.001). Children of parents who have had symptoms of post traumatic stress disorder (PTSD), the most important persons that they communicate were schoolmates and they had problem in communicating with fathers and males. According to satisfaction children whose parents suffered from PTSD were showing distinction in contacts with their families, relatives, schoolmates and formal contacts.

Mind the Organelle Gap - Peroxisome Contact Sites in Disease.

PubMed

Castro, Inês Gomes; Schuldiner, Maya; Zalckvar, Einat

2018-03-01

The eukaryotic cell is organized as a complex grid system where membrane-bound cellular compartments, organelles, must be localized to the right place at the right time. One way to facilitate correct organelle localization and organelle cooperation is through membrane contact sites, areas of close proximity between two organelles that are bridged by protein/lipid complexes. It is now clear that all organelles physically contact each other. The main focus of this review is contact sites of peroxisomes, central metabolic hubs whose defects lead to a variety of diseases. New peroxisome contacts, their tethering complexes and functions have been recently discovered. However, if and how peroxisome contacts contribute to the development of peroxisome-related diseases is still a mystery. Copyright © 2018 Elsevier Ltd. All rights reserved.

Adhesive Contact Sweeper

NASA Technical Reports Server (NTRS)

Patterson, Jonathan D.

1993-01-01

Adhesive contact sweeper removes hair and particles vacuum cleaner leaves behind, without stirring up dust. Also cleans loose rugs. Sweeper holds commercially available spools of inverted adhesive tape. Suitable for use in environments in which air kept free of dust; optics laboratories, computer rooms, and areas inhabited by people allergic to dust. For carpets, best used in tandem with vacuum cleaner; first pass with vacuum cleaner removes coarse particles, and second pass with sweeper extracts fine particles. This practice extends useful life of adhesive spools.

Analysis of rolling contact spall life in 440 C steel bearing rims

NASA Technical Reports Server (NTRS)

Bastias, P. C.; Bhargava, V.; Bower, A. P.; Du, J.; Gupta, V.; Hahn, G. T.; Kulkarni, S. M.; Kumar, A. M.; Leng, X.; Rubin, C. A.

1991-01-01

The results of a two year study of the mechanisms of spall failure in the HPOTP bearings are described. The objective was to build a foundation for detailed analyses of the contact life in terms of: cyclic plasticity, contact mechanics, spall nucleation, and spall growth. Since the laboratory rolling contact testing is carried out in the 3 ball/rod contact fatigue testing machine, the analysis of the contacts and contact lives produced in this machine received attention. The results from the experimentally observed growth lives are compared with calculated predictions derived from the fracture mechanics calculations.

Social Contacts and Mixing Patterns Relevant to the Spread of Infectious Diseases

PubMed Central

Mossong, Joël; Hens, Niel; Jit, Mark; Beutels, Philippe; Auranen, Kari; Mikolajczyk, Rafael; Massari, Marco; Salmaso, Stefania; Tomba, Gianpaolo Scalia; Wallinga, Jacco; Heijne, Janneke; Sadkowska-Todys, Malgorzata; Rosinska, Magdalena; Edmunds, W. John

2008-01-01

Background Mathematical modelling of infectious diseases transmitted by the respiratory or close-contact route (e.g., pandemic influenza) is increasingly being used to determine the impact of possible interventions. Although mixing patterns are known to be crucial determinants for model outcome, researchers often rely on a priori contact assumptions with little or no empirical basis. We conducted a population-based prospective survey of mixing patterns in eight European countries using a common paper-diary methodology. Methods and Findings 7,290 participants recorded characteristics of 97,904 contacts with different individuals during one day, including age, sex, location, duration, frequency, and occurrence of physical contact. We found that mixing patterns and contact characteristics were remarkably similar across different European countries. Contact patterns were highly assortative with age: schoolchildren and young adults in particular tended to mix with people of the same age. Contacts lasting at least one hour or occurring on a daily basis mostly involved physical contact, while short duration and infrequent contacts tended to be nonphysical. Contacts at home, school, or leisure were more likely to be physical than contacts at the workplace or while travelling. Preliminary modelling indicates that 5- to 19-year-olds are expected to suffer the highest incidence during the initial epidemic phase of an emerging infection transmitted through social contacts measured here when the population is completely susceptible. Conclusions To our knowledge, our study provides the first large-scale quantitative approach to contact patterns relevant for infections transmitted by the respiratory or close-contact route, and the results should lead to improved parameterisation of mathematical models used to design control strategies. PMID:18366252

Cd1-xZnxTe photodetectors with transparent conductive ZnO contacts

NASA Astrophysics Data System (ADS)

Tang, Ke; Huang, Jian; Lu, Yuanxi; Hu, Yan; Shen, Yibin; Zhang, Jijun; Gu, Qingmiao; Wang, Linjun; Lu, Yicheng

2018-03-01

High quality Cd1-xZnxTe (CZT) films were prepared using the close-spaced sublimation (CSS) technique. CZT film UV (ultraviolet) photodetectors were fabricated with B and Ga co-doped ZnO (BGZO) transparent conductive interdigitated contacts. The contact properties of BGZO/CZT were investigated by the transmission line model (TLM). The results indicate that a good ohmic contact is formed between BGZO and CZT with a very low contact resistivity of about 0.26 Ω·cm2. Compared with CZT photodetectors with Au contacts, the detectors with BGZO contacts show a higher value of UV photo response.

Predictors of Late Reperfusion in STEMI Patients Undergoing Primary Angioplasty. Impact of the Place of First Medical Contact.

PubMed

Carol Ruiz, Antoni; Masip Utset, Josep; Ariza Solé, Albert

2017-03-01

The benefit of primary angioplasty may be reduced if there are delays to reperfusion. Identification of the variables associated with these delays could improve health care. Analysis of the Codi Infart registry of Catalonia and of the time to angioplasty depending on the place of first medical contact. In 3832 patients analyzed, first medical contact took place in primary care centers in 18% and in hospitals without a catheterization laboratory in 37%. Delays were longer in these 2 groups than in patients attended by the outpatient emergency medical system or by hospitals with a catheterization laboratory (P < .0001, results in median): first medical contact to reperfusion indication time was 42minutes in both (overall 35minutes); first medical contact to artery opening time was 131 and 143minutes, respectively (overall 121minutes); total ischemia time was 230 and 260minutes (overall 215minutes). First medical contact to artery opening time > 120minutes was strongly associated with first medical contact in a center without a catheterization laboratory (OR, 4.96; 95% confidence interval, 4.14-5.93), and other factors such as age, previous coronary surgery, first medical contact during evening hours, nondiagnostic electrocardiogram, and Killip class ≥ III. Mortality at 30 days and 1 year was 5.6% and 8.7% and was independently associated with age, longer delay to angioplasty, Killip class ≥ II, and first medical contact in a center with a catheterization laboratory. In more than 50% of patients requiring primary angioplasty, the first medical contact occurs in centers without a catheterization laboratory, which is an important predictor of delay from diagnosis to artery opening. Copyright © 2016 Sociedad Española de Cardiología. Published by Elsevier España, S.L.U. All rights reserved.

CTBTO Contractor Laboratory Test Sample Production Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bob Hague; Tracy Houghton; Nick Mann

2013-08-01

In October 2012 scientists from both Idaho National Laboratory (INL) and the CTBTO contact laboratory at Seibersdorf, Austria designed a system and capability test to determine if the INL could produce and deliver a short lived radio xenon standard in time for the standard to be measured at the CTBTO contact laboratory at Seibersdorf, Austria. The test included sample standard transportation duration and potential country entrance delays at customs. On October 23, 2012 scientists at the Idaho National Laboratory (INL) prepared and shipped a Seibersdorf contract laboratory supplied cylinder. The canister contained 1.0 scc of gas that consisted of 70%more » xenon and 30% nitrogen by volume. The t0 was October 24, 2012, 1200 ZULU. The xenon content was 0.70 +/ 0.01 scc at 0 degrees C. The 133mXe content was 4200 +/ 155 dpm per scc of stable xenon on t0 (1 sigma uncertainty). The 133Xe content was 19000 +/ 800 dpm per scc of stable xenon on t0 (1 sigma uncertainty).« less

Assessment of clinical symptoms in household contacts of confirmed pertussis cases.

PubMed

Domínguez, Angela; Soldevila, Núria; Caylà, Joan A; García-Cenoz, Manuel; Ferrús, Glòria; Sala-Farré, Maria Rosa; Álvarez, Josep; Carol, Mònica; Barrabeig, Irene; Camps, Neus; Coronas, Lorena; Muñoz-Almagro, Carmen; Godoy, Pere

2017-11-01

We assessed the value of the clinical symptoms included in the case definition of pertussis in household contacts of laboratory-confirmed cases. A prospective epidemiological study was made in two Spanish regions. Household contacts were identified for each confirmed case reported during 2012 and 2013. Two clinical samples were taken to determine the presence or absence of Bordetella pertussis by culture or real-time PCR. Clinical variables, age and vaccination status were recorded. Positive and negative likelihood ratios (PLR, NLR) were estimated for each symptom. 2852 household contacts of 688 confirmed cases were reported. 178 household contacts with clinical symptoms were analyzed: 150 were laboratory confirmed and 28 were not. The clinical symptom with the highest PLR in comparison with the NLR was paroxysmal cough(PLR 4.76; 95% CI 1.91-11.87 and NLR 0.37; 95% CI 0.28-0.49). The contrast between the PLR and NLR was especially important for persons aged <18 years (PLR 7.08; 95% CI 1.10-45.74 and NLR 0.32; 95% CI 0.21-0.49). The clinical symptoms of pertussis are poor predictors of pertussis disease, independently of the vaccination status. Differences were observed between persons aged <18 years and adults. To adopt the appropriate treatment and control measures, rapid laboratory confirmation by PCR of all household contacts of confirmed cases who present any clinical symptoms compatible with pertussis should be recommended. Copyright © 2017 The British Infection Association. Published by Elsevier Ltd. All rights reserved.

A new method for evaluation of compatibility of contact lenses and lens cases with contact lens disinfecting solutions.

PubMed

Mowrey-McKee, Mary; Borazjani, Roya; Collins, Gary; Cook, James; Norton, Susan

2012-01-01

The purpose of this article is to describe new methodology, antimicrobial efficacy endpoint methodology to determine compatibility of contact lens solutions, lens cases and hydrogel lenses for disinfection (AEEMC), to evaluate the effect of a contact lens and a lens case on disinfection efficacy, and to present the ring test used to justify the use of the method in multiple laboratories. A prototype solution containing chlorhexidine as the disinfecting agent and four representative lens types (group I and IV hydrogels and two silicone hydrogels) were used in these ring tests. Five laboratories participated in the chemical and microbiologic analyses. The residual chlorhexidine in lens cases containing the contact lenses was determined using high-performance liquid chromatography; uptake by the lenses was then determined by extrapolation. For the microbiologic part of the study, a contact lens was placed in the well of the lens case, inoculated at 10 to 10 cfu (colony forming units) per lens with microorganisms in 10% organic soil. The microorganisms, Pseudomonas aeruginosa, Serratia marcescens, Staphylococcus aureus, Candida albicans, and Fusarium solani, were prepared as in International Organization for Standardization (ISO) 14729. After a 3- to 10-min exposure time, the prototype solution was dispensed into each well. Aliquots of the inoculated solutions were removed at 4 and 24 hrs and 7 and 30 days and cultured in neutralizing media for determination of survivors; lenses were also cultured for survivors. Chemical uptake data confirmed the differences observed in kill of the challenge organisms according to lens type. It was observed that the culturing of the solution provided adequate data to show the effect of a lens on disinfection efficacy of a lens care product. The findings of the ring test indicated that the separate culturing of the contact lenses is not necessary for routine assessment. The methodology in the November 12, 2008, draft standard (AEEMC

European Fiber Optics. USAF Laboratory Experts’ Visit,

DTIC Science & Technology

1979-12-01

emitting at 480 ma. AE-Telefunken Telecomunications and Cable Systems Division Postfach 1120 7150 Backnang, Germany Principal Contact: Dr. K. D. 4chenkel...alignment purposes. Standard Telecomunication Laboratories, Inc. (STL) London Road Harlow, Essex 017 9NA, England Principal Contact: Dr. M. Chown - Manager

Cognitive functioning is more closely related to real-life mobility than to laboratory-based mobility parameters.

PubMed

Giannouli, Eleftheria; Bock, Otmar; Zijlstra, Wiebren

2018-03-01

Increasing evidence indicates that mobility depends on cognitive resources, but the exact relationships between various cognitive functions and different mobility parameters still need to be investigated. This study examines the hypothesis that cognitive functioning is more closely related to real-life mobility performance than to mobility capacity as measured with standardized laboratory tests. The final sample used for analysis consisted of 66 older adults (72.3 ± 5.6 years). Cognition was assessed by measures of planning (HOTAP test), spatial working memory (Grid-Span test) and visuospatial attention (Attention Window test). Mobility capacity was assessed by an instrumented version of the Timed Up-and-Go test (iTUG). Mobility performance was assessed with smartphones which collected accelerometer and GPS data over one week to determine the spatial extent and temporal duration of real-life activities. Data analyses involved an exploratory factor analysis and correlation analyses. Mobility measures were reduced to four orthogonal factors: the factor 'real-life mobility' correlated significantly with most cognitive measures (between r   =  .229 and r   =  .396); factors representing 'sit-to-stand transition' and 'turn' correlated with fewer cognitive measures (between r   =  .271 and r   =  .315 and between r   =  .210 and r   =  .316, respectively), and the factor representing straight gait correlated with only one cognitive measure ( r   =  .237). Among the cognitive functions tested, visuospatial attention was associated with most mobility measures, executive functions with fewer and spatial working memory with only one mobility measure. Capacity and real-life performance represent different aspects of mobility. Real-life mobility is more closely associated with cognition than mobility capacity, and in our data this association is most pronounced for visuospatial attention. The close link between real-life mobility and visuospatial attention

Planter closing wheel effects on cotton emergence in a conservation tillage system

USDA-ARS?s Scientific Manuscript database

Closing wheels on a row crop planter help provide good seed-soil contact during planting and can influence emergence and crop stand. Various types of closing wheels are available to producers for use on planters. Seven closing wheel types were used on a row crop planter planting cotton in a conser...

Approximate stresses in 2-D flat elastic contact fretting problems

NASA Astrophysics Data System (ADS)

Urban, Michael Rene

Fatigue results from the cyclic loading of a solid body. If the body subject to fatigue is in contact with another body and relative sliding motion occurs between these two bodies, then rubbing surface damage can accelerate fatigue failure. The acceleration of fatigue failure is especially important if the relative motion between the two bodies results in surface damage without excessive surface removal via wear. The situation just described is referred to as fretting fatigue. Understanding of fretting fatigue is greatly enhanced if the stress state associated with fretting can be characterized. For Hertzian contact, this can readily be done. Unfortunately, simple stress formulae are not available for flat body contact. The primary result of the present research is the development of a new, reasonably accurate, approximate closed form expression for 2-dimensional contact stresses which has been verified using finite element modeling. This expression is also combined with fracture mechanics to provide a simple method of determining when a crack is long enough to no longer be affected by the contact stress field. Lower bounds on fatigue life can then easily be calculated using fracture mechanics. This closed form expression can also be used to calculate crack propagation within the contact stress field. The problem of determining the cycles required to generate an initial crack and what to choose as an initial crack size is unresolved as it is in non-fretting fatigue.

Investigation of Crimean-Congo Hemorrhagic Fever Virus Transmission from Patients to Relatives: A Prospective Contact Tracing Study

PubMed Central

Gozel, Mustafa Gokhan; Bakir, Mehmet; Oztop, Atifet Yasemin; Engin, Aynur; Dokmetas, Ilyas; Elaldi, Nazif

2014-01-01

We investigated the possibility of transmission of Crimean-Congo hemorrhagic fever (CCHF) virus through respiratory and physical contact. In this prospective study, we traced 116 close relatives of confirmed CCHF cases who were in close contact with the patients during the acute phase of the infection and evaluated the type of contact between patients and their relatives. These relatives were followed for clinical signs or symptoms indicative of CCHF disease, blood samples of those with and without clinical signs were analyzed for CCHF virus immunoglobulin M and G (IgM and IgG, respectively) by enzyme-linked immunosorbent assay. No close relatives developed any signs or symptoms of CCHF and were negative for CCHF virus IgM and IgG. The results suggest that CCHF virus is not easily transmitted from person to person through respiratory or physical contact. PMID:24166037

Lateral spreading of Au contacts on InP

NASA Technical Reports Server (NTRS)

Fatemi, Navid S.; Weizer, Victor G.

1990-01-01

The contact spreading phenomenon observed when small area Au contacts on InP are annealed at temperatures above about 400 C was investigated. It was found that the rapid lateral expansion of the contact metallization which consumes large quantities of InP during growth is closely related to the third stage in the series of solid state reactions that occur between InP and Au, i.e., to the Au3In-to-Au9In4 transition. Detailed descriptions are presented of both the spreading process and the Au3In-to-Au9In4 transition along with arguments that the two processes are manifestations of the same basic phenomenon.

News | Argonne National Laboratory

Science.gov Websites

Skip to main content Argonne National Laboratory Toggle Navigation Toggle Search Home Learning solvers Home Learning Center Undergraduates Graduates Faculty Partners News & Events News & Events -4114 Contact Us Argonne Educational Programs is committed to providing a learning environment that

Dynamic of nasal colonization by methicillin-resistant Staphylococcus aureus ST398 and ST1 after mupirocin treatment in a family in close contact with pigs.

PubMed

Lozano, Carmen; Aspiroz, Carmen; Lasarte, Juan J; Gómez-Sanz, Elena; Zarazaga, Myriam; Torres, Carmen

2011-01-01

Nasal colonization by methicillin-resistant Staphylococcus aureus (MRSA) was evaluated after a mupirocin treatment in a family previously colonized by MRSA sequence type ST398 and ST1, who lived close to a pig farm. Eight nasal samples were swabbed from each of the four family members on different moments after mupirocin treatment. The efficacy of treatment was low in those family members who worked in the farm, and higher in the remaining two family members with sporadic contact with pigs. In addition, nasal and skin swabs from randomly selected pigs of the farm were taken. MRSA were detected in 33% of pigs tested. All MRSA isolates obtained were characterized by Staphylococcal-Cassette-Chromosome mec (SCCmec) determination, Multilocus-Sequence-Typing (MLST), spa- and agr-typing, Pulsed-field-gel-electrophoresis (PFGE), antimicrobial susceptibility, detection of antimicrobial resistance genes, and toxin gene profiling. Spa-types t011, t1255 and t1197 were detected in humans and animals, with indistinguishable PFGE patterns, suggesting animal to human MRSA transmission. Each spa-type was ascribed to a specific pulsotype. Spa-types t127 and t108 were only detected in MRSA isolates obtained from humans, and t012 only in those from animals. MRSA ST1-t127 isolates and some ST398-t011 and ST398-t1197 isolates presented a multiantimicrobial-resistance phenotype. None of them harbored lukF/lukS, tst, eta and etb virulence genes. This study showed that the efficacy of nasal MRSA decolonization in healthy people with very close contact with pigs is especially low. Copyright © 2010 Elsevier Ltd. All rights reserved.

Forensic Analysis of a Contact Lens in a Murder Case.

PubMed

Zwerling, Charles S

2016-03-01

Contact lenses have had rare relevance in trials and/or investigations. After 5 years of burial, orbital remnants were retrieved from an exhumed body and subsequently identified as a key piece of material evidence in a murder trial. The exhumed case materials were evaluated under laboratory conditions and were determined to be contact lens remnants. Contact lens fracture and burial simulation studies were performed to provide additional corroboration of the physical findings of the exhumed contact lens remnants. This material evidence was instrumental in providing factual proof refuting the defendant's testimony in the murder trial. A brief history of contact lens composition and use is provided for understanding the methods and observational results. This forensic case study represents the first published documentation of a contact lens from an exhumed body being used in a murder investigation and establishes an operational procedure for future forensic contact lens examinations. © 2016 American Academy of Forensic Sciences.

Experimental study of tyre/road contact forces in rolling conditions for noise prediction

NASA Astrophysics Data System (ADS)

Cesbron, Julien; Anfosso-Lédée, Fabienne; Duhamel, Denis; Ping Yin, Hai; Le Houédec, Donatien

2009-02-01

This paper deals with the experimental study of dynamical tyre/road contact for noise prediction. In situ measurements of contact forces and close proximity noise levels were carried out for a slick tyre rolling on six different road surfaces between 30 and 50 km/h. Additional texture profiles of the tested surfaces were taken on the wheel track. Normal contact stresses were measured at a sampling frequency of 10752 Hz using a line of pressure sensitive cells placed both along and perpendicular to the rolling direction. The contact areas obtained during rolling were smaller than in static conditions. This is mainly explained by the dynamical properties of tyre compounds, like the viscoelastic behaviour of the rubber. Additionally the root-mean-square of the resultant contact forces at various speeds was in the same order for a given road surface, while their spectra were quite different. This is certainly due to a spectral influence of bending waves propagating in the tyre during rolling, especially when the wavelength is small in comparison with the size of the contact patch. Finally, the levels of contact forces and close proximity noise measured at 30 km/h were correlated. Additional correlations with texture levels were performed. The results show that the macro-texture generates contact forces linearly around 800 Hz and consequently noise levels between 500 and 1000 Hz via the vibrations transmitted to the tyre.

Wetting behavior on hexagonally close-packed polystyrene bead arrays with different topographies.

PubMed

Park, Yi-Seul; Yoon, Seo Young; Lee, Jin Seok

2016-01-21

Herein, we investigated the wetting behavior of hexagonally close-packed polystyrene bead arrays with different bead diameters and surface flatness. The contact angle was found to be influenced by the surface roughness as well as the contact area of the polystyrene bead array with a water droplet.

Transmission events revealed in tuberculosis contact investigations in London.

PubMed

Cavany, Sean M; Vynnycky, Emilia; Sumner, Tom; Macdonald, Neil; Thomas, H Lucy; White, Jacqui; White, Richard G; Maguire, Helen; Anderson, Charlotte

2018-04-27

Contact tracing is a key part of tuberculosis prevention and care, aiming to hasten diagnosis and prevent transmission. The proportion of case-contact pairs for which recent transmission occurred and the typical timespans between the index case and their contact accessing care are not known; we aimed to calculate these. We analysed individual-level TB contact tracing data, collected in London from 20/01/2011-31/12/2015, linked to tuberculosis surveillance and MIRU-VNTR 24-locus strain-typing information. Of pairs of index cases and contacts diagnosed with active tuberculosis, 85/314 (27%) had strain typing data available for both. Of these pairs, 79% (67/85) shared indistinguishable isolates, implying probable recent transmission. Of pairs in which both contact and the index case had a social risk factor, 11/11 (100%) shared indistinguishable isolates, compared to 55/75 (75%) of pairs in which neither had a social risk factor (P = 0.06). The median time interval between the index case and their contact accessing care was 42 days (IQR: 16, 96). As over 20% of pairs did probably not involve recent transmission between index case and contact, the effectiveness of contact tracing is not necessarily limited to those circumstances where the index case has transmitted disease to their close contacts.

My Friends Right Next to Me: A Laboratory Investigation on Predictors and Consequences of Experiencing Social Closeness on Social Networking Sites.

PubMed

Neubaum, German; Krämer, Nicole C

2015-08-01

In the last decade, research has provided a series of insights into how and why the use of social networking sites (SNSs) can be socially and psychologically beneficial for individuals. The present research extends this evidence by focusing on the concept of social closeness as a feeling experienced when using SNSs. In a laboratory setting, participants (N=60) spent 10 minutes on Facebook, and then reported their experiences during this session. Analyses of participants' usage behavior and their experiences revealed that the more time users spent interacting with other users (e.g., commenting on updates), the closer they felt to other people. Interacting with others also predicted users' positive emotional states after Facebook use; this effect may be explained by the perception of social closeness. This study is one of the first to employ momentary measures, offering a further theoretical link between active SNS use and well-being.

Time Dependent Frictional Changes in Ice due to Contact Area Changes

NASA Astrophysics Data System (ADS)

Sevostianov, V.; Lipovsky, B. P.; Rubinstein, S.; Dillavou, S.

2017-12-01

Sliding processes along the ice-bed interface of Earth's great ice sheets are the largest contributor to our uncertainty in future sea level rise. Laboratory experiments that have probed sliding processes have ubiquitously shown that ice-rock interfaces strengthen while in stationary contact (Schulson and Fortt, 2013; Zoet et al., 2013; McCarthy et al., 2017). This so-called frictional ageing effect may have profound consequences for ice sheet dynamics because it introduces the possibility of basal strength hysteresis. Furthermore this effect is quite strong in ice-rock interfaces (more than an order of magnitude more pronounced than in rock-rock sliding) and can double in frictional strength in a matter of minutes, much faster than most frictional aging (Dieterich, 1972; Baumberger and Caroli, 2006). Despite this importance, the underling physics of frictional ageing of ice remain poorly understood. Here we conduct laboratory experiments to image the microscopic points of contact along an ice-glass interface. We optically measure changes in the real area of contact over time using measurements of this reflected optical light intensity. We show that contact area increases with time of stationary contact. This result suggests that thermally enhanced creep of microscopic icy contacts is responsible for the much larger frictional ageing observed in ice-rock versus rock-rock interfaces. Furthermore, this supports a more physically detailed description of the thermal dependence of basal sliding than that used in the current generation of large scale ice sheet models.

Microbial contamination of soft contact lenses & accessories in asymptomatic contact lens users

PubMed Central

Thakur, Deeksha V.; Gaikwad, Ujjwala N.

2014-01-01

Background & objectives: With increasing use of soft contact lenses the incidence of contact lens induced infections is also increasing. This study was aimed to assess the knowledge of new and existing contact lens users about the risk of microbial contamination associated with improper use and maintenance of contact lenses, type of microbial flora involved and their potential to cause ophthalmic infections. Methods: Four samples each from 50 participants (n=200) were collected from the lenses, lens care solutions, lens care solution bottles and lens cases along with a questionnaire regarding their lens use. The samples were inoculated onto sheep blood agar, Mac Conkey's agar and Sabouraud's dextrose agar. Organisms were identified using standard laboratory protocols. Results: Overall rate of microbial contamination among the total samples was 52 per cent. The most and the least contaminated samples were found to be lens cases (62%) and lens care solution (42%), respectively. The most frequently isolated contaminant was Staphylococcus aureus (21%) followed by Pseudomonas species (19.5%). Majority (64%) of the participants showed medium grade of compliance to lens cleaning practices. Rate of contamination was 100 and 93.75 per cent respectively in those participants who showed low and medium compliance to lens care practices as compared to those who had high level of compliance (43.75%) (P<0.05). Interpretation & conclusions: Lens care practices amongst the participants were not optimum which resulted into high level contamination. Hence, creating awareness among the users about the lens care practices and regular cleaning and replacements of lens cases are required. PMID:25297366

Microbial contamination of soft contact lenses & accessories in asymptomatic contact lens users.

PubMed

Thakur, Deeksha V; Gaikwad, Ujjwala N

2014-08-01

With increasing use of soft contact lenses the incidence of contact lens induced infections is also increasing. This study was aimed to assess the knowledge of new and existing contact lens users about the risk of microbial contamination associated with improper use and maintenance of contact lenses, type of microbial flora involved and their potential to cause ophthalmic infections. Four samples each from 50 participants (n=200) were collected from the lenses, lens care solutions, lens care solution bottles and lens cases along with a questionnaire regarding their lens use. The samples were inoculated onto sheep blood agar, Mac Conkey's agar and Sabouraud's dextrose agar. Organisms were identified using standard laboratory protocols. Overall rate of microbial contamination among the total samples was 52 per cent. The most and the least contaminated samples were found to be lens cases (62%) and lens care solution (42%), respectively. The most frequently isolated contaminant was Staphylococcus aureus (21%) followed by Pseudomonas species (19.5%). Majority (64%) of the participants showed medium grade of compliance to lens cleaning practices. Rate of contamination was 100 and 93.75 per cent respectively in those participants who showed low and medium compliance to lens care practices as compared to those who had high level of compliance (43.75%) (P<0.05). Lens care practices amongst the participants were not optimum which resulted into high level contamination. Hence, creating awareness among the users about the lens care practices and regular cleaning and replacements of lens cases are required.

Studies of the quenching phenomenon in delayed contact hypersensitivity reactions.

PubMed

Basketter, D A; Allenby, C F

1991-09-01

Studies in guinea pig and man have shown that eugenol can quench non-specifically contact urticarial responses, whereas limonene seems largely ineffective. In a comprehensive series of studies, there was little evidence of quenching of delayed contact hypersensitivity reactions to cinnamic aldehyde or citral, including in 'pre-quenched' material supplied by a perfume/flavour company, and in a similar mixture prepared in this laboratory, in the guinea pig model. In addition, there was no evidence of the quenching by eugenol of allergic reactions to cinnamic aldehyde in a panel of human subjects with a proven history of cinnamic-aldehyde-induced allergic contact dermatitis. Overall, the results lend little credibility to earlier literature reports of quenching phenomena in delayed contact hypersensitivity responses.

Restructuring the CS 1 classroom: Examining the effect of open laboratory-based classes vs. closed laboratory-based classes on Computer Science 1 students' achievement and attitudes toward computers and computer courses

NASA Astrophysics Data System (ADS)

Henderson, Jean Foster

The purpose of this study was to assess the effect of classroom restructuring involving computer laboratories on student achievement and student attitudes toward computers and computer courses. The effects of the targeted student attributes of gender, previous programming experience, math background, and learning style were also examined. The open lab-based class structure consisted of a traditional lecture class with a separate, unscheduled lab component in which lab assignments were completed outside of class; the closed lab-based class structure integrated a lab component within the lecture class so that half the class was reserved for lecture and half the class was reserved for students to complete lab assignments by working cooperatively with each other and under the supervision and guidance of the instructor. The sample consisted of 71 students enrolled in four intact classes of Computer Science I during the fall and spring semesters of the 2006--2007 school year at two southern universities: two classes were held in the fall (one at each university) and two classes were held in the spring (one at each university). A counterbalanced repeated measures design was used in which all students experienced both class structures for half of each semester. The order of control and treatment was rotated among the four classes. All students received the same amount of class and instructor time. A multivariate analysis of variance (MANOVA) via a multiple regression strategy was used to test the study's hypotheses. Although the overall MANOVA model was statistically significant, independent follow-up univariate analyses relative to each dependent measure found that the only significant research factor was math background: Students whose mathematics background was at the level of Calculus I or higher had significantly higher student achievement than students whose mathematics background was less than Calculus I. The results suggest that classroom structures that

Support across two generations: children's closeness to grandparents following parental divorce and remarriage.

PubMed

Lussier, Gretchen; Deater-Deckard, Kirby; Dunn, Judy; Davies, Lisa

2002-09-01

There has been relatively little research on the role of grandparents as a source of support for children during and following their parents' marital transitions. In this study, we examined children's contact with and closeness to grandparents in different family types (i.e., two biological parents, single mother, stepparent). Participants included 155 children from the Avon Brothers and Sisters Study. Parent and child interviews and questionnaires regarding the children's relationships with maternal and paternal biological and stepgrandparents were examined. There were family type differences in rates of contact with grandparents as well as children's closeness to grandparents. Furthermore, children's and parents' view about these relationships with grandparents were modestly correlated, suggesting that children often held different views about their closeness to their grandparents than did their parents. Greater closeness to grandparents was associated with fewer adjustment problems.

Repertoire of free-living protozoa in contact lens solutions.

PubMed

Bouchoucha, Ibtissem; Aziz, Aurore; Hoffart, Louis; Drancourt, Michel

2016-10-29

The repertoire of free-living protozoa in contact lens solutions is poorly known despite the fact that such protozoa may act as direct pathogens and may harbor intra-cellular pathogens. Between 2009 and 2014, the contact lens solutions collected from patients presenting at our Ophthalmology Department for clinically suspected keratitis, were cultured on non-nutrient agar examined by microscope for the presence of free-living protozoa. All protozoa were identified by 18S rRNA gene sequencing. A total of 20 of 233 (8.6 %) contact lens solution specimens collected from 16 patients were cultured. Acanthamoeba amoeba in 16 solutions (80 %) collected from 12 patients and Colpoda steini, Cercozoa sp., Protostelium sp. and a eukaryotic more closely related to Vermamoeba sp., were each isolated in one solution. Cercozoa sp., Colpoda sp., Protostelium sp. and Vermamoeba sp. are reported for the first time as contaminating contact lens solutions. The repertoire of protozoa in contact lens solutions is larger than previously known.

Screening contacts of patients with extrapulmonary TB for latent TB infection.

PubMed

Humphreys, Anna; Abbara, Aula; Williams, Sion; John, Laurence; Corrah, Tumena; McGregor, Alastair; Davidson, Robert N

2018-03-01

2016 TB National Institute for Health and Care Excellence (NICE) guidelines imply that contacts of extrapulmonary TB do not require screening for latent TB infection. At our high TB prevalence site, we identified 189 active cases of TB for whom there were 698 close contacts. 29.1% of the contacts of pulmonary TB and 10.7% of the contacts of extrapulmonary TB had active or latent TB infection. This supports screening contacts of extrapulmonary TB at our site and presents a way to access high-risk individuals. We propose to continue to screen the contacts of our patients with extrapulmonary TB and recommend other TB units audit their local results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

From the Nano- to the Macroscale - Bridging Scales for the Moving Contact Line Problem

NASA Astrophysics Data System (ADS)

Nold, Andreas; Sibley, David; Goddard, Benjamin; Kalliadasis, Serafim; Complex Multiscale Systems Team

2016-11-01

The moving contact line problem remains an unsolved fundamental problem in fluid mechanics. At the heart of the problem is its multiscale nature: a nanoscale region close to the solid boundary where the continuum hypothesis breaks down, must be resolved before effective macroscale parameters such as contact line friction and slip can be obtained. To capture nanoscale properties very close to the contact line and to establish a link to the macroscale behaviour, we employ classical density-functional theory (DFT), in combination with extended Navier-Stokes-like equations. Using simple models for viscosity and slip at the wall, we compare our computations with the Molecular Kinetic Theory, by extracting the contact line friction, depending on the imposed temperature of the fluid. A key fluid property captured by DFT is the fluid layering at the wall-fluid interface, which has a large effect on the shearing properties of a fluid. To capture this crucial property, we propose an anisotropic model for the viscosity, which also allows us to scrutinize the effect of fluid layering on contact line friction.

Pharmacist-led Tdap vaccination of close contacts of neonates in a women's hospital.

PubMed

Mills, Brittany; Fensterheim, Leonard; Taitel, Michael; Cannon, Adam

2014-01-16

Pertussis can cause severe illness and death in infants. Immunization of family members with the tetanus toxoid, reduced diphtheria toxoids, and acellular pertussis (Tdap) vaccine can decrease risk of pertussis infection among infants. A community pharmacy on a women's hospital campus implemented a Tdap vaccination pilot program. To investigate the rate of Tdap vaccination among close contacts of neonates in a women's hospital pharmacy and to assess the impact of a coordinated pharmacy and hospital Tdap vaccination program. The intervention entailed education from hospital staff who explained the risks of pertussis, advocated the benefits of vaccination, and encouraged family members to be vaccinated. In the on-site clinic or in the pharmacy, pharmacists administered vaccine to eligible patients. Rates of Tdap vaccinations in the intervention pharmacy with in-hospital vaccination were compared to comparison pharmacies without Tdap interventions. In the pre-study period (December 2008-November 2010), there were 31 Tdap vaccinations administered at the intervention pharmacy (mean=1.3/month); during the study period (December 2010-November 2012), 2045 Tdap vaccinations were administered (mean=85.2/month). In four comparison hospital-campus pharmacies, there were 77 vaccinations (mean=0.8/month) during the pre-study period and 817 vaccinations (mean=8.5/month) during the study period. There were 155 vaccinations administered in 44 area-community pharmacies (mean=0.1/month) during the pre-study period and 2930 (mean=2.8/month) during the study period. The intervention pharmacy had the highest average monthly rate of change in Tdap volume from pre-study to study period (83.9), compared to comparison hospital-campus pharmacies (7.7, p<.001) and area-community pharmacies (2.7, p<.001). During the study period, the estimated Tdap vaccination coverage per live births was 8.1% in the intervention pharmacy versus 5.5% in the comparison hospital-campus pharmacies (p<.001). Tdap

STUDIES IN EDUCATIONAL CLOSED-CIRCUIT TELEVISION.

ERIC Educational Resources Information Center

MARTIN, JOHN R.; AND OTHERS

THE 3 MOST OBJECTED-TO FEATURES OF INSTRUCTIONAL TV ARE (1) RESTRICTIONS IMPOSED BY THE USE OF A SPECIAL STUDIO, (2) LOSS OF TEACHER-STUDENT CONTACT, (3) THE LIMITED VIEWING AREA OF TV SCREENS. THIS STUDY INVESTIGATED 4 CLOSED-CIRCUIT TV COURSES IN AN ATTEMPT TO MINIMIZE FEATURES (1) AND (2). OVER THE ACADEMIC YEAR 1957-58 AT THE CASE INSTITUTE,…

Active alignment/contact verification system

DOEpatents

Greenbaum, William M.

2000-01-01

A system involving an active (i.e. electrical) technique for the verification of: 1) close tolerance mechanical alignment between two component, and 2) electrical contact between mating through an elastomeric interface. For example, the two components may be an alumina carrier and a printed circuit board, two mating parts that are extremely small, high density parts and require alignment within a fraction of a mil, as well as a specified interface point of engagement between the parts. The system comprises pairs of conductive structures defined in the surfaces layers of the alumina carrier and the printed circuit board, for example. The first pair of conductive structures relate to item (1) above and permit alignment verification between mating parts. The second pair of conductive structures relate to item (2) above and permit verification of electrical contact between mating parts.

Follow-up of Contacts of Middle East Respiratory Syndrome Coronavirus-Infected Returning Travelers, the Netherlands, 2014.

PubMed

Mollers, Madelief; Jonges, Marcel; Pas, Suzan D; van der Eijk, Annemiek A; Dirksen, Kees; Jansen, Casper; Gelinck, Luc B S; Leyten, Eliane M S; Thurkow, Ingrid; Groeneveld, Paul H P; van Gageldonk-Lafeber, Arianne B; Koopmans, Marion P; Timen, Aura

2015-09-01

Notification of 2 imported cases of infection with Middle East respiratory syndrome coronavirus in the Netherlands triggered comprehensive monitoring of contacts. Observed low rates of virus transmission and the psychological effect of contact monitoring indicate that thoughtful assessment of close contacts is prudent and must be guided by clinical and epidemiologic risk factors.

A novel procedure for the extraction of protein deposits from soft hydrophilic contact lenses for analysis.

PubMed

Keith, D; Hong, B; Christensen, M

1997-05-01

A quick, simple, and efficient extraction technique was developed for the removal of protein from soft hydrophilic contact lenses. An extraction solvent consisting of a 50:50 mix of 0.2% trifluoroacetic acid and acetonitrile was used to remove protein from in vitro laboratory-deposited and human-worn contact lenses. The protein removed was analyzed using HPLC, bicinchoninic acid (BCA) analysis, and SDS-PAGE gel electreophoresis. Extraction efficiency for lysozyme from laboratory-deposited Group IV lenses was determined to be approximately 100%. Group IV human-worn contact lenses were extracted and analyzed for lysozyme by HPLC and total protein by bicinchoninic acid (BCA) analysis. Groups I, II, III, and IV contact lenses deposited with an artificial tear protein solution and human-worn lenses were extracted and analyzed by SDS-PAGE gel electreophoresis and micro-BCA. The ACN/TFA procedure offers a simple, quick, and efficient extraction technique for removal of protein from contact lenses for subsequent analysis.

78 FR 34135 - Sunshine Act Meetings; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-06

..., Chicago, Illinois 60611. The agenda for this meeting follows: Closed meeting notice: (1) Chief Information Officer Position The person to contact for more information is Martha P. Rico, Secretary to the Board...

Pediatric "pet consort dermatitis"-Allergic contact dermatitis from transfer of bronopol from a pet cat.

PubMed

Hamann, Dathan; Ridpath, Alyson; Fernandez Faith, Esteban

2018-06-26

Consort dermatitis refers to an allergic contact dermatitis caused by transfer from an intimate contact to a sensitized patient. Although close contact with other humans most commonly provokes consort dermatitis, pets have been the source in a minority of cases. We present a unique case of transfer dermatitis from a patient's cat litter to her forearms. Pediatric dermatologists should be aware of the possibility of consort or "transfer" allergic contact dermatitis from pets. © 2018 Wiley Periodicals, Inc.

Internship Opportunities | Argonne National Laboratory

Science.gov Websites

Skip to main content Argonne National Laboratory Toggle Navigation Toggle Search Home Learning -class research to tomorrow's STEM problem solvers Home Learning Center Undergraduates Graduates Faculty ) 252-4114 Contact Us Argonne Educational Programs is committed to providing a learning environment that

Shigella Infections in Household Contacts of Pediatric Shigellosis Patients in Rural Bangladesh.

PubMed

George, Christine Marie; Ahmed, Shahnawaz; Talukder, Kaisar A; Azmi, Ishrat J; Perin, Jamie; Sack, R Bradley; Sack, David A; Stine, O Colin; Oldja, Lauren; Shahnaij, Mohammad; Chakraborty, Subhra; Parvin, Tahmina; Bhuyian, Sazzadul Islam; Bouwer, Edward; Zhang, Xiaotong; Hasan, Trisheeta N; Luna, Sharmin J; Akter, Fatema; Faruque, Abu S G

2015-11-01

To examine rates of Shigella infections in household contacts of pediatric shigellosis patients, we followed contacts and controls prospectively for 1 week after the index patient obtained care. Household contacts of patients were 44 times more likely to develop a Shigella infection than were control contacts (odds ratio 44.7, 95% CI 5.5-361.6); 29 (94%) household contacts of shigellosis patients were infected with the same species and serotype as the index patient's. Pulsed-field gel electrophoresis showed that 14 (88%) of 16 with infected contacts had strains that were indistinguishable from or closely related to the index patient's strain. Latrine area fly counts were higher in patient households compared with control households, and 2 patient household water samples were positive for Shigella. We show high susceptibility of household contacts of shigellosis patients to Shigella infections and found environmental risk factors to be targeted in future interventions.

The significance of oxygen during contact lens wear.

PubMed

Papas, Eric B

2014-12-01

In order to establish the relevance of oxygen to contemporary contact lens practice, a review of the literature was conducted. The results indicate that there are a number of processes occurring in the normal healthy eye where oxygen is required and which are potentially affected by the presence of a contact lens. These activities appear to take place at all corneal levels, as well as at the limbus. Evidence from laboratory, clinical and modelling studies indicates that what constitutes normal oxygenation (normoxia) depends on, among other things, the physiological system under consideration, corneal location and the state of eye closure. This diversity is reflected in the wide range of minimum lens oxygen transmissibility (Dk/t) requirements that are present in a literature. Copyright © 2014 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Laboratory exercises on oscillation modes of pipes

NASA Astrophysics Data System (ADS)

Haeberli, Willy

2009-03-01

This paper describes an improved lab setup to study the vibrations of air columns in pipes. Features of the setup include transparent pipes which reveal the position of a movable microphone inside the pipe; excitation of pipe modes with a miniature microphone placed to allow access to the microphone stem for open, closed, or conical pipes; and sound insulation to avoid interference between different setups in a student lab. The suggested experiments on the modes of open, closed, and conical pipes, the transient response of a pipe, and the effect of pipe diameter are suitable for introductory physics laboratories, including laboratories for nonscience majors and music students, and for more advanced undergraduate laboratories. For honors students or for advanced laboratory exercises, the quantitative relation between the resonance width and damping time constant is of interest.

Close To You? How Parent–Adult Child Contact Is Influenced by Family Patterns

PubMed Central

Spitze, Glenna; Ward, Russell A.; Zhuo, Yue (Angela)

2016-01-01

Objectives. Intergenerational contacts occur in the context of other family relationships. We examine how in-person contacts among parents and all adult children affect each other, focusing on proximity and other predictors to assess whether and how visiting is correlated across adult children. Methods. We use a modeling approach derived from an adaptation of multilevel models to provide a convenient mechanism by which to write child-specific equations, each with its own set of predictors, and wherein one child’s attribute values can be attached to other children’s records. Results. We find that parent–adult child visiting is positively correlated across siblings, but the frequency of visiting within families is not directly reciprocated. Rather, visiting responds to common family factors. Visiting declines with distance, but there are strong discontinuities in the effect. Distance between parents and a focal child is positively associated with visiting with other children. Discussion. The empirical patterns we report can be framed within enhancement and compensation models. Positive correlations and cross-sibling interactions that juxtapose levels of visiting against not seeing a child in last 12 months are consistent with the enhancement model. The cross-sibling interaction for distance, whereby one child’s farther distance leads to more visits reported with others, provides evidence of a countervailing, though, weaker, pattern of compensation for proximity. PMID:26024669

Effects of medial meniscus posterior horn avulsion and repair on tibiofemoral contact area and peak contact pressure with clinical implications.

PubMed

Marzo, John M; Gurske-DePerio, Jennifer

2009-01-01

Avulsion of the posterior horn attachment of the medial meniscus can compromise load-bearing ability, produce meniscus extrusion, and result in tibiofemoral joint-space narrowing, articular cartilage damage, and osteoarthritis. Avulsion of the posterior horn of the medial meniscus will increase peak contact pressure and decrease contact area in the medial compartment of the knee, and posterior horn repair will restore contact area and peak contact pressures to values of the control knee. Controlled laboratory study. Eight fresh-frozen human cadaveric knees had tibiofemoral peak contact pressures and contact area measured in the control state. The posterior horn of the medial meniscus was avulsed from its insertion and knees were retested. The meniscal avulsion was repaired by suture through a transosseous tunnel and the knees were tested a third time. Avulsion of the posterior horn attachment of the medial meniscus resulted in a significant increase in medial joint peak contact pressure (from 3841 kPa to 5084 kPa) and a significant decrease in contact area (from 594 mm(2) to 474 mm(2)). Repair of the avulsion resulted in restoration of the loading profiles to values equal to the control knee, with values of 3551 kPa for peak pressure and 592 mm(2) for contact area. Posterior horn medial meniscal root avulsion leads to deleterious alteration of the loading profiles of the medial joint compartment and results in loss of hoop stress resistance, meniscus extrusion, abnormal loading of the joint, and early knee medial-compartment degenerative changes. The repair technique described restores the ability of the medial meniscus to absorb hoop stress and eliminate joint-space narrowing, possibly decreasing the risk of degenerative disease.

Diagnosis of Tuberculosis in Three Zoo Elephants and a Human Contact - Oregon, 2013.

PubMed

Zlot, Amy; Vines, Jennifer; Nystrom, Laura; Lane, Lindsey; Behm, Heidi; Denny, Justin; Finnegan, Mitch; Hostetler, Trevor; Matthews, Gloria; Storms, Tim; DeBess, Emilio

2016-01-08

In 2013, public health officials in Multnomah County, Oregon, started an investigation of a tuberculosis (TB) outbreak among elephants and humans at a local zoo. The investigation ultimately identified three bull elephants with active TB and 118 human contacts of the elephants. Ninety-six (81%) contacts were evaluated, and seven close contacts were found to have latent TB infection. The three bulls were isolated and treated (elephants with TB typically are not euthanized) to prevent infection of other animals and humans, and persons with latent infection were offered treatment. Improved TB screening methods for elephants are needed to prevent exposure of human contacts.

Cost of gentamicin assays carried out by microbiology laboratories.

PubMed Central

Vacani, P F; Malek, M M; Davey, P G

1993-01-01

AIMS--To assess the current range of prices charged for gentamicin assays in United Kingdom laboratories; and to examine the laboratories' likely response to increases or decreases in the demand for the service. METHODS--A postal survey of the 420 members of the Association of Medical Microbiologists was used to establish the range of prices charged for aminoglycoside assays. Additionally, eight private institutions were contacted to determine what the private sector was charging for aminoglycoside assays. Reagent costs in the NHS laboratories were calculated by dividing the total cost of all aminoglycoside assay kits by the number of samples analysed. RESULTS--The NHS and the private institutions both showed a wide price variation. Prices charged to an in-hospital requester for a peak and trough assay ranged from 5.00 pounds to 68.20 pounds (n = 44), and to an external private hospital, under a bulk service contract, from 5.00 pounds to 96.00 pounds (n = 47). Prices charged by private laboratories ranged from 49.00 pounds to 84.00 pounds (n = 8). There was a log linear correlation in the NHS laboratories between the reagent costs per assay and the number of assays performed per year, and most laboratories thought that their price per assay would be sensitive to increases or decreases in demand. Laboratories which had purchased their assay machines had lower reagent costs per assay but higher repair and maintenance costs. Overall, number of assays performed and method of payment for assay machinery only accounted for 44.8% of the observed variation in assay kit costs. CONCLUSIONS--The price range for gentamicin assays in the United Kingdom is wide and is only partially explained by the number of assays performed. Most laboratories believe that they would experience a reduction in unit cost as output increases. The currently offered range of prices is, in part, due to variation in the laboratories' approach to costing the service provided and some laboratories

Engineering education using a remote laboratory through the Internet

NASA Astrophysics Data System (ADS)

Axaopoulos, Petros J.; Moutsopoulos, Konstantinos N.; Theodoridis, Michael P.

2012-03-01

An experiment using real hardware and under real test conditions can be remotely conducted by engineering students and other interested individuals in the world via the Internet and with the capability of live video streaming from the test site. The presentation of this innovative experiment refers to the determination of the current voltage characteristic curve of a photovoltaic panel installed on the roof of a laboratory, facing south and with the ability to alter its tilt angle, using a closed loop servo motor mounted on the horizontal axis of the panel. The user has the sense of a direct contact with the system since they can intervene and alter the tilt of the panel and get a live visual feedback besides the remote instrumentation panel. The whole procedure takes a few seconds to complete and the characteristic curve is displayed in a chart giving the student and anyone else interested the chance to analyse the results and understand the respective theory; meanwhile, the test data are stored in a file for future use. This type of remote experiment could be used for distance education, training, part-time study and to help students with disabilities to participate in a laboratory environment.

Contact dermatitis in students practicing sports: incidence of rubber sensitisation.

PubMed

Ventura, M T; Dagnello, M; Matino, M G; Di Corato, R; Giuliano, G; Tursi, A

2001-04-01

Over the last few years, changes in cutaneous homoeostasis resulting from sports activities have been reported. In particular, alterations in sweating mechanisms, the hydrolipid barrier, and surface bacterial flora, together with exposure to atmospheric conditions and the need to use medicaments, detergents, and other topical substances, predispose subjects to allergic contact dermatitis. To evaluate the incidence of allergic contact dermatitis in a group of young people practising sports activities. Patch tests were performed to confirm the diagnosis of irritant or allergic dermatitis; in addition, the radioallergoabsorbent test (RAST) to latex was evaluated in the group studied. Allergic contact dermatitis caused by thiourams (23.3%) and mercaptobenzothiazole (20.9%) was prevalent. Other haptens, such as benzocaine and nickel, which are contained in clothing, equipment, topical medicaments, and creams used for massage, were also allergenic. In two cases, RAST positivity to latex was registered. -The results suggest that close contact with sports equipment may increase the incidence of allergic contact dermatitis. Students practising certain sports may have "professional" allergic contact dermatitis to additives used in the production of rubber.

On the Integration of Remote Experimentation into Undergraduate Laboratories--Pedagogical Approach

ERIC Educational Resources Information Center

Esche, Sven K.

2005-01-01

This paper presents an Internet-based open approach to laboratory instruction. In this article, the author talks about an open laboratory approach using a multi-user multi-device remote facility. This approach involves both the direct contact with the computer-controlled laboratory setup of interest with the students present in the laboratory…

Open-cycle magnetohydrodynamic power plant based upon direct-contact closed-loop high-temperature heat exchanger

DOEpatents

Berry, G.F.; Minkov, V.; Petrick, M.

1981-11-02

A magnetohydrodynamic (MHD) power generating system is described in which ionized combustion gases with slag and seed are discharged from an MHD combustor and pressurized high temperature inlet air is introduced into the combustor for supporting fuel combustion at high temperatures necessary to ionize the combustion gases, and including a heat exchanger in the form of a continuous loop with a circulating heat transfer liquid such as copper oxide. The heat exchanger has an upper horizontal channel for providing direct contact between the heat transfer liquid and the combustion gases to cool the gases and condense the slag which thereupon floats on the heat transfer liquid and can be removed from the channel, and a lower horizontal channel for providing direct contact between the heat transfer liquid and pressurized air for preheating the inlet air. The system further includes a seed separator downstream of the heat exchanger.

Open-cycle magnetohydrodynamic power plant based upon direct-contact closed-loop high-temperature heat exchanger

DOEpatents

Berry, Gregory F.; Minkov, Vladimir; Petrick, Michael

1988-01-05

A magnetohydrodynamic (MHD) power generating system in which ionized combustion gases with slag and seed are discharged from an MHD combustor and pressurized high temperature inlet air is introduced into the combustor for supporting fuel combustion at high temperatures necessary to ionize the combustion gases, and including a heat exchanger in the form of a continuous loop with a circulating heat transfer liquid such as copper oxide. The heat exchanger has an upper horizontal channel for providing direct contact between the heat transfer liquid and the combustion gases to cool the gases and condense the slag which thereupon floats on the heat transfer liquid and can be removed from the channel, and a lower horizontal channel for providing direct contact between the heat transfer liquid and pressurized air for preheating the inlet air. The system further includes a seed separator downstream of the heat exchanger.

Open-cycle magnetohydrodynamic power plant based upon direct-contact closed-loop high-temperature heat exchanger

DOEpatents

Berry, Gregory F.; Minkov, Vladimir; Petrick, Michael

1988-01-01

A magnetohydrodynamic (MHD) power generating system in which ionized combustion gases with slag and seed are discharged from an MHD combustor and pressurized high temperature inlet air is introduced into the combustor for supporting fuel combustion at high temperatures necessary to ionize the combustion gases, and including a heat exchanger in the form of a continuous loop with a circulating heat transfer liquid such as copper oxide. The heat exchanger has an upper horizontal channel for providing direct contact between the heat transfer liquid and the combustion gases to cool the gases and condense the slag which thereupon floats on the heat transfer liquid and can be removed from the channel, and a lower horizontal channel for providing direct contact between the heat transfer liquid and pressurized air for preheating the inlet air. The system further includes a seed separator downstream of the heat exchanger.

No Evidence for Spontaneous Lipid Transfer at ER-PM Membrane Contact Sites.

PubMed

Merklinger, Elisa; Schloetel, Jan-Gero; Spitta, Luis; Thiele, Christoph; Lang, Thorsten

2016-04-01

Non-vesicular lipid transport steps play a crucial role in lipid trafficking and potentially include spontaneous exchange. Since membrane contact facilitates this lipid transfer, it is most likely to occur at membrane contact sites (MCS). However, to date it is unknown whether closely attached biological membranes exchange lipids spontaneously. We have set up a system for studying the exchange of lipids at MCS formed between the endoplasmic reticulum (ER) and the plasma membrane. Contact sites were stably anchored and the lipids cholesterol and phosphatidylcholine (PC) were not capable of transferring spontaneously into the opposed bilayer. We conclude that physical contact between two associated biological membranes is not sufficient for transfer of the lipids PC and cholesterol.

Foot Placement Modulation Diminishes for Perturbations Near Foot Contact.

PubMed

Vlutters, Mark; Van Asseldonk, Edwin H F; van der Kooij, Herman

2018-01-01

Whenever a perturbation occurs during walking we have to maintain our balance using the recovery strategies that are available to us. Foot placement adjustment is often considered an important recovery strategy. However, because this strategy takes time it is likely a poor option if the foot is close to contact at the instant a perturbation occurs. The main goal of this study is to gain a better understanding of how humans deal with balance perturbations during walking if foot placement adjustments are constrained by time. Ten healthy subjects walked on an instrumented treadmill and received mediolateral and anteroposterior pelvis perturbations at various instances during the single support phase. The results show that foot placement modulation in the first recovery step following anteroposterior perturbations is fairly invariant of the perturbation magnitude and direction, regardless of the onset instance. For mediolateral perturbations, foot placement adjustments strongly modulate with the perturbation magnitude and direction, but these effects diminish when the perturbation onset is closer to the instant of foot contact. For most perturbations the first recovery step was consistent across subjects for all onset instances. However, in the second step various strategies arose that were not consistent across subjects, nor within subjects, especially for perturbations applied close to foot contact. Despite these different strategies, the COP location following foot contact strongly related to the COM velocity throughout these strategies. The results show that humans have various ways to compensate for limited availability of a foot placement strategy, with strategy selection highly dependent on the instant during the gait phase at which the perturbation is applied.

Tear Oxygen Under Hydrogel and Silicone Hydrogel Contact Lenses in Humans

PubMed Central

Bonanno, Joseph A.; Clark, Christopher; Pruitt, John; Alvord, Larry

2011-01-01

Purpose To determine the tear oxygen tension under a variety of conventional and silicone hydrogel contact lenses in human subjects. Methods Three hydrogel and five silicone hydrogel lenses (Dk/t = 17 to 329) were coated on the back surface with an oxygen sensitive, bovine serum albumin-Pd meso-tetra (4-carboxyphenyl) porphine complex (BSA-porphine). Each lens type was placed on the right eye of 15 non-contact lens wearers to obtain a steady-state open eye tear oxygen tension using oxygen sensitive phosphorescence decay of BSA-porphine. A closed-eye oxygen tension estimate was obtained by measuring the change in tear oxygen tension after 5 min of eye closure. In separate experiments, a goggle was placed over the lens wearing eye and a gas mixture (PO2 = 51 torr) flowed over the lens to simulate anterior lens oxygen tension during eye closure. Results Mean open eye oxygen tension ranged from 58 to 133 torr. Closed eye estimates ranged from 11 to 42 torr. Oxygen tension under the goggle ranged from 8 to 48 torr and was higher than the closed eye estimate for six out of the eight lenses, suggesting that the average closed eye anterior lens surface oxygen tension is <51 torr. For Dk/t >30, the measured tear oxygen tension is significantly lower than that predicted from previous studies. Conclusions The phosphorescence decay methodology is capable of directly measuring the in vivo post lens PO2 of high Dk/t lenses without disturbing the contact lens or cornea. Our data indicate that increasing Dk/t up to and beyond 140 continues to yield increased flux into the central cornea. PMID:19609230

Tear oxygen under hydrogel and silicone hydrogel contact lenses in humans.

PubMed

Bonanno, Joseph A; Clark, Christopher; Pruitt, John; Alvord, Larry

2009-08-01

To determine the tear oxygen tension under a variety of conventional and silicone hydrogel contact lenses in human subjects. Three hydrogel and five silicone hydrogel lenses (Dk/t = 17 to 329) were coated on the back surface with an oxygen sensitive, bovine serum albumin-Pd meso-tetra (4-carboxyphenyl) porphine complex (BSA-porphine). Each lens type was placed on the right eye of 15 non-contact lens wearers to obtain a steady-state open eye tear oxygen tension using oxygen sensitive phosphorescence decay of BSA-porphine. A closed-eye oxygen tension estimate was obtained by measuring the change in tear oxygen tension after 5 min of eye closure. In separate experiments, a goggle was placed over the lens wearing eye and a gas mixture (PO2 = 51 torr) flowed over the lens to simulate anterior lens oxygen tension during eye closure. Mean open eye oxygen tension ranged from 58 to 133 torr. Closed eye estimates ranged from 11 to 42 torr. Oxygen tension under the goggle ranged from 8 to 48 torr and was higher than the closed eye estimate for six out of the eight lenses, suggesting that the average closed eye anterior lens surface oxygen tension is <51 torr. For Dk/t >30, the measured tear oxygen tension is significantly lower than that predicted from previous studies. The phosphorescence decay methodology is capable of directly measuring the in vivo post lens PO2 of high Dk/t lenses without disturbing the contact lens or cornea. Our data indicate that increasing Dk/t up to and beyond 140 continues to yield increased flux into the central cornea.

Integrated Source Case Investigation for Tuberculosis (TB) and HIV in the Caregivers and Household Contacts of Hospitalised Young Children Diagnosed with TB in South Africa: An Observational Study

PubMed Central

Lala, Sanjay G.; Little, Kristen M.; Tshabangu, Nkeko; Moore, David P.; Msandiwa, Reginah; van der Watt, Martin; Chaisson, Richard E.; Martinson, Neil A.

2015-01-01

Background Contact tracing, to identify source cases with untreated tuberculosis (TB), is rarely performed in high disease burden settings when the index case is a young child with TB. As TB is strongly associated with HIV infection in these settings, we used source case investigation to determine the prevalence of undiagnosed TB and HIV in the caregivers and household contacts of hospitalised young children diagnosed with TB in South Africa. Methods Caregivers and household contacts of 576 young children (age ≤7 years) with TB diagnosed between May 2010 and August 2012 were screened for TB and HIV. The primary outcome was the detection of laboratory-confirmed, newly-diagnosed TB disease and/or HIV-infection in close contacts. Results Of 576 caregivers, 301 (52·3%) self-reported HIV-positivity. Newly-diagnosed HIV infection was detected in 63 (22·9%) of the remaining 275 caregivers who self-reported an unknown or negative HIV status. Screening identified 133 (23·1%) caregivers eligible for immediate anti-retroviral therapy (ART). Newly-diagnosed TB disease was detected in 23 (4·0%) caregivers. In non-caregiver household contacts (n = 1341), the prevalence of newly-diagnosed HIV infection and TB disease was 10·0% and 3·2% respectively. On average, screening contacts of every nine children with TB resulted in the identification of one case of newly-diagnosed TB disease, three cases of newly diagnosed HIV-infection, and three HIV-infected persons eligible for ART. Conclusion In high burden countries, source case investigation yields high rates of previously undiagnosed HIV and TB infection in the close contacts of hospitalised young children diagnosed with TB. Furthermore, integrated screening identifies many individuals who are eligible for immediate ART. Similar studies, with costing analyses, should be undertaken in other high burden settings–integrated source case investigation for TB and HIV should be routinely undertaken if our findings are confirmed

Beyond-laboratory-scale prediction for channeling flows through subsurface rock fractures with heterogeneous aperture distributions revealed by laboratory evaluation

NASA Astrophysics Data System (ADS)

Ishibashi, Takuya; Watanabe, Noriaki; Hirano, Nobuo; Okamoto, Atsushi; Tsuchiya, Noriyoshi

2015-01-01

The present study evaluates aperture distributions and fluid flow characteristics for variously sized laboratory-scale granite fractures under confining stress. As a significant result of the laboratory investigation, the contact area in fracture plane was found to be virtually independent of scale. By combining this characteristic with the self-affine fractal nature of fracture surfaces, a novel method for predicting fracture aperture distributions beyond laboratory scale is developed. Validity of this method is revealed through reproduction of the results of laboratory investigation and the maximum aperture-fracture length relations, which are reported in the literature, for natural fractures. The present study finally predicts conceivable scale dependencies of fluid flows through joints (fractures without shear displacement) and faults (fractures with shear displacement). Both joint and fault aperture distributions are characterized by a scale-independent contact area, a scale-dependent geometric mean, and a scale-independent geometric standard deviation of aperture. The contact areas for joints and faults are approximately 60% and 40%. Changes in the geometric means of joint and fault apertures (µm), em, joint and em, fault, with fracture length (m), l, are approximated by em, joint = 1 × 102 l0.1 and em, fault = 1 × 103 l0.7, whereas the geometric standard deviations of both joint and fault apertures are approximately 3. Fluid flows through both joints and faults are characterized by formations of preferential flow paths (i.e., channeling flows) with scale-independent flow areas of approximately 10%, whereas the joint and fault permeabilities (m2), kjoint and kfault, are scale dependent and are approximated as kjoint = 1 × 10-12 l0.2 and kfault = 1 × 10-8 l1.1.

Bioassays to evaluate non-contact spatial repellency, contact irritancy, and acute toxicity of permethrin-treated clothing against nymphal Ixodes scapularis ticks.

PubMed

Eisen, Lars; Rose, Dominic; Prose, Robert; Breuner, Nicole E; Dolan, Marc C; Thompson, Karen; Connally, Neeta

2017-10-01

Summer-weight clothing articles impregnated with permethrin are available as a personal protective measure against human-biting ticks in the United States. However, very few studies have addressed the impact of contact with summer-weight permethrin-treated textiles on tick vigor and behavior. Our aim was to generate new knowledge of how permethrin-treated textiles impact nymphal Ixodes scapularis ticks, the primary vectors in the eastern United States of the causative agents of Lyme disease, human anaplasmosis, and human babesiosis. We developed a series of bioassays designed to: (i) clarify whether permethrin-treated textiles impact ticks through non-contact spatial repellency or contact irritancy; (ii) evaluate the ability of ticks to remain in contact with vertically oriented permethrin-treated textiles, mimicking contact with treated clothing on arms or legs; and (iii) determine the impact of timed exposure to permethrin-treated textiles on the ability of ticks to move and orient toward a human finger stimulus, thus demonstrating normal behavior. Our results indicate that permethrin-treated textiles provide minimal non-contact spatial repellency but strong contact irritancy against ticks, manifesting as a "hot-foot" effect and resulting in ticks actively dislodging from contact with vertically oriented treated textile. Preliminary data suggest that the contact irritancy hot-foot response may be weaker for field-collected nymphs as compared with laboratory-reared nymphs placed upon permethrin-treated textile. We also demonstrate that contact with permethrin-treated textiles negatively impacts the vigor and behavior of nymphal ticks for >24h, with outcomes ranging from complete lack of movement to impaired movement and unwillingness of ticks displaying normal movement to ascend onto a human finger. The protective effect of summer-weight permethrin-treated clothing against tick bites merits further study. Published by Elsevier GmbH.

Stretching single atom contacts at multiple subatomic step-length.

PubMed

Wei, Yi-Min; Liang, Jing-Hong; Chen, Zhao-Bin; Zhou, Xiao-Shun; Mao, Bing-Wei; Oviedo, Oscar A; Leiva, Ezequiel P M

2013-08-14

This work describes jump-to-contact STM-break junction experiments leading to novel statistical distribution of last-step length associated with conductance of a single atom contact. Last-step length histograms are observed with up to five for Fe and three for Cu peaks at integral multiples close to 0.075 nm, a subatomic distance. A model is proposed in terms of gliding from a fcc hollow-site to a hcp hollow-site of adjacent atomic planes at 1/3 regular layer spacing along with tip stretching to account for the multiple subatomic step-length behavior.

Characteristics of human encounters and social mixing patterns relevant to infectious diseases spread by close contact: a survey in Southwest Uganda.

PubMed

le Polain de Waroux, O; Cohuet, S; Ndazima, D; Kucharski, A J; Juan-Giner, A; Flasche, S; Tumwesigye, E; Arinaitwe, R; Mwanga-Amumpaire, J; Boum, Y; Nackers, F; Checchi, F; Grais, R F; Edmunds, W J

2018-04-11

Quantification of human interactions relevant to infectious disease transmission through social contact is central to predict disease dynamics, yet data from low-resource settings remain scarce. We undertook a social contact survey in rural Uganda, whereby participants were asked to recall details about the frequency, type, and socio-demographic characteristics of any conversational encounter that lasted for ≥5 min (henceforth defined as 'contacts') during the previous day. An estimate of the number of 'casual contacts' (i.e. < 5 min) was also obtained. In total, 566 individuals were included in the study. On average participants reported having routine contact with 7.2 individuals (range 1-25). Children aged 5-14 years had the highest frequency of contacts and the elderly (≥65 years) the fewest (P < 0.001). A strong age-assortative pattern was seen, particularly outside the household and increasingly so for contacts occurring further away from home. Adults aged 25-64 years tended to travel more often and further than others, and males travelled more frequently than females. Our study provides detailed information on contact patterns and their spatial characteristics in an African setting. It therefore fills an important knowledge gap that will help more accurately predict transmission dynamics and the impact of control strategies in such areas.

Eye protection in dental laboratories.

PubMed

Palenik, C J

1997-09-01

Many dental laboratory procedures increase the chances of serious eye injury. This would include traumatic injuries due to projectiles or through exposure to harsh chemicals or heat and infections from contact with patient body fluids. To help assure a safer working environment, awareness of the need for eye protection must be established and maintained by all laboratory personnel. The purpose of this article are: 1) to list the applicable federal regulations concerning eye safety in dental laboratory workplaces; 2) to describe the various types of appropriate eyewear; and 3) to identify which protective devices best prevent exposure to specific types of hazards. The goal of this article is to help dental laboratories with their employee safety programs, especially concerning the selection of protective eyewear. Such programs must include engineering controls and work practice controls plus appropriate personal protective equipment. Laboratories today must comply with safety mandates in the most effective and efficient manner.

77 FR 75639 - National Cancer Institute Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-21

... DEPARTMENT OF HEALTH AND HUMAN SERVICES National Institutes of Health National Cancer Institute... Proposed Frederick National Laboratory for Cancer Research Strategic Plan. Place: The Lawrence Berkeley..., Berkeley, CA 94720. Contact Person: Thomas M. Vollberg, Sr., Ph.D., Executive Secretary, National Cancer...

A Low-G Silicon Inertial Micro-Switch with Enhanced Contact Effect Using Squeeze-Film Damping.

PubMed

Peng, Yingchun; Wen, Zhiyu; Li, Dongling; Shang, Zhengguo

2017-02-16

Contact time is one of the most important properties for inertial micro-switches. However, it is usually less than 20 μs for the switch with rigid electrode, which is difficult for the external circuit to recognize. This issue is traditionally addressed by designing the switch with a keep-close function or flexible electrode. However, the switch with keep-close function requires an additional operation to re-open itself, causing inconvenience for some applications wherein repeated monitoring is needed. The switch with a flexible electrode is usually fabricated by electroplating technology, and it is difficult to realize low-g switches (<50 g) due to inherent fabrication errors. This paper reports a contact enhancement using squeeze-film damping effect for low-g switches. A vertically driven switch with large proof mass and flexible springs was designed based on silicon micromachining, in order to achieve a damping ratio of 2 and a threshold value of 10 g. The proposed contact enhancement was investigated by theoretical and experimental studies. The results show that the damping effect can not only prolong the contact time for the dynamic acceleration load, but also reduce the contact bounce for the quasi-static acceleration load. The contact time under dynamic and quasi-static loads was 40 μs and 570 μs, respectively.

Design, Fabrication and Testing of Two Different Laboratory Prototypes of CSI-based Induction Heating Units

NASA Astrophysics Data System (ADS)

Roy, M.; Sengupta, M.

2012-09-01

Induction heating is a non-contact heating process which became popular due to its energy efficiency. Current source inverter (CSI) based induction heating units are commonly used in the industry. Most of these CSIs are thyristor based, since thyristors of higher ratings are easily available. These being load commutated apparatus a start-up circuit is needed to initiate commutation. In this paper the design and fabrication of two laboratory prototypes have been presented. The first one, a SCR-based CSI fed controlled induction heating unit (IHU), has been tested with two different types of start-up procedures. Thereafter the fabrication and performance of another IGBT-based CSI is compared with the thyristor-based CSI for a 2 kW, 10 kHz application. These two types of CSIs are fully fabricated in laboratory along with the IHU. Performance analysis and simulation of two different CSIs has been done by using SequelGUI2. The triggering pulses for the inverter devices (for both CSI devices as well as auxilliary thyristor of start-up circuit) have been generated and closed-loop control has been done in FPGA platform built around an Altera make cyclone EPIC12Q240C processor which can be programmed using Quartus II software. Close agreement between simulated and experimental results highlight the accuracy of the experimental work.

Internal audit in a microbiology laboratory.

PubMed Central

Mifsud, A J; Shafi, M S

1995-01-01

AIM--To set up a programme of internal laboratory audit in a medical microbiology laboratory. METHODS--A model of laboratory based process audit is described. Laboratory activities were examined in turn by specimen type. Standards were set using laboratory standard operating procedures; practice was observed using a purpose designed questionnaire and the data were analysed by computer; performance was assessed at laboratory audit meetings; and the audit circle was closed by re-auditing topics after an interval. RESULTS--Improvements in performance scores (objective measures) and in staff morale (subjective impression) were observed. CONCLUSIONS--This model of process audit could be applied, with amendments to take local practice into account, in any microbiology laboratory. PMID:7665701

Closed loop problems in biomechanics. Part II--an optimization approach.

PubMed

Vaughan, C L; Hay, J G; Andrews, J G

1982-01-01

A closed loop problem in biomechanics may be defined as a problem in which there are one or more closed loops formed by the human body in contact with itself or with an external system. Under certain conditions the problem is indeterminate--the unknown forces and torques outnumber the equations. Force transducing devices, which would help solve this problem, have serious drawbacks, and existing methods are inaccurate and non-general. The purposes of the present paper are (1) to develop a general procedure for solving closed loop problems; (2) to illustrate the application of the procedure; and (3) to examine the validity of the procedure. A mathematical optimization approach is applied to the solution of three different closed loop problems--walking up stairs, vertical jumping and cartwheeling. The following conclusions are drawn: (1) the method described is reasonably successful for predicting horizontal and vertical reaction forces at the distal segments although problems exist for predicting the points of application of these forces; (2) the results provide some support for the notion that the human neuromuscular mechanism attempts to minimize the joint torques and thus, to a certain degree, the amount of muscular effort; (3) in the validation procedure it is desirable to have a force device for each of the distal segments in contact with a fixed external system; and (4) the method is sufficiently general to be applied to all classes of closed loop problems.

Dynamic Test Program, Contact Power Collection for High Speed Tracked Vehicles

DOT National Transportation Integrated Search

1973-01-01

A laboratory test program is defined for determining the dynamic characteristics of a contact power collection system for a high speed tracked vehicle. The use of a hybrid computer is conjuntion with hydraulic exciters to simulate the expected dynami...

How-to-Do-It: Maintaining Parasitic Lampreys in Closed Laboratory Systems.

ERIC Educational Resources Information Center

Cochran, Philip A.

1989-01-01

Describes modifications and procedures needed for parasitic lampreys to be kept in a closed system. Presents information dealing with obtaining the organisms, tank modifications, temperature, feeding, disease prevention, and animal welfare. A discussion is included. (RT)

Beyond Cassie equation: Local structure of heterogeneous surfaces determines the contact angles of microdroplets

PubMed Central

Zhang, Bo; Wang, Jianjun; Liu, Zhiping; Zhang, Xianren

2014-01-01

The application of Cassie equation to microscopic droplets is recently under intense debate because the microdroplet dimension is often of the same order of magnitude as the characteristic size of substrate heterogeneities, and the mechanism to describe the contact angle of microdroplets is not clear. By representing real surfaces statistically as an ensemble of patterned surfaces with randomly or regularly distributed heterogeneities (patches), lattice Boltzmann simulations here show that the contact angle of microdroplets has a wide distribution, either continuous or discrete, depending on the patch size. The origin of multiple contact angles observed is ascribed to the contact line pinning effect induced by substrate heterogeneities. We demonstrate that the local feature of substrate structure near the contact line determines the range of contact angles that can be stabilized, while the certain contact angle observed is closely related to the contact line width. PMID:25059292

Effect of Tabor parameter on hysteresis losses during adhesive contact

NASA Astrophysics Data System (ADS)

Ciavarella, M.; Greenwood, J. A.; Barber, J. R.

2017-01-01

The Tabor parameter μ is conventionally assumed to determine the range of applicability of the classical 'JKR' solution for adhesive elastic contact of a sphere and a plane, with the variation of the contact area and approach with load, and in particular the maximum tensile force (the pull-off force) being well predicted for μ > 5 . Here we show that the hysteretic energy loss during a contact separation cycle is significantly overestimated by the JKR theory, even at quite large values of μ. This stems from the absence of long-range tensile forces in the JKR theory, which implies that jump into contact is delayed until the separation α = 0 . We develop an approximate solution based on the use of Wu's solution with van der Waals interactions for jump-in, and the JKR theory for jump out of contact, and show that for μ > 5 , the predicted hysteresis loss is then close to that found by direct numerical solutions using the Lennard-Jones force law. We also show how the same method can be adapted to allow for contact between bodies with finite support stiffness.

Communication and the laboratory physician

PubMed Central

Penistan, J. L.

1973-01-01

A clinical laboratory documentation system is described, suitable for community hospitals without computer services. The system is cumulative and is designed to provide the laboratory physician with the clinical information necessary for intelligent review and comment on the laboratory's findings. The mode of presentation of requests to the laboratory and lay-out of the reports to the clinicians are designed to make the two-way communication as close and personal as possible; to encourage the selection of those investigations likely to prove rewarding, and to discourage unnecessary investigation. The possibility of important data escaping notice is minimized. The system is economical in capital equipment, labour and supplies. PMID:4758594

Optimal contact definition for reconstruction of contact maps.

PubMed

Duarte, Jose M; Sathyapriya, Rajagopal; Stehr, Henning; Filippis, Ioannis; Lappe, Michael

2010-05-27

Contact maps have been extensively used as a simplified representation of protein structures. They capture most important features of a protein's fold, being preferred by a number of researchers for the description and study of protein structures. Inspired by the model's simplicity many groups have dedicated a considerable amount of effort towards contact prediction as a proxy for protein structure prediction. However a contact map's biological interest is subject to the availability of reliable methods for the 3-dimensional reconstruction of the structure. We use an implementation of the well-known distance geometry protocol to build realistic protein 3-dimensional models from contact maps, performing an extensive exploration of many of the parameters involved in the reconstruction process. We try to address the questions: a) to what accuracy does a contact map represent its corresponding 3D structure, b) what is the best contact map representation with regard to reconstructability and c) what is the effect of partial or inaccurate contact information on the 3D structure recovery. Our results suggest that contact maps derived from the application of a distance cutoff of 9 to 11A around the Cbeta atoms constitute the most accurate representation of the 3D structure. The reconstruction process does not provide a single solution to the problem but rather an ensemble of conformations that are within 2A RMSD of the crystal structure and with lower values for the pairwise average ensemble RMSD. Interestingly it is still possible to recover a structure with partial contact information, although wrong contacts can lead to dramatic loss in reconstruction fidelity. Thus contact maps represent a valid approximation to the structures with an accuracy comparable to that of experimental methods. The optimal contact definitions constitute key guidelines for methods based on contact maps such as structure prediction through contacts and structural alignments based on maximum

Laboratory accidents--a matter of attitude.

PubMed

Karim, N; Choe, C K

2000-12-01

This is a prospective study on accidents occurring in the Pathology laboratories of Hospital Ipoh over the 3-year period from January 1996 to October 1999. 15 mishaps were recorded. The location of the accidents were the histology (40%), microbiology (33%), haematology (20%) and cytology (7%) laboratories. No mishaps were reported from the clinical chemistry, blood bank and outpatient laboratories. Cuts by sharp objects were the most common injuries sustained (47%) followed by splashes and squirts by fluid such as blood or chemicals (27%). There was 1 case each of contact with biohazardous fluid, burn, allergy and accidental drinking of disinfectant. 67% of the accidents involved medical laboratory technicians, 20% involved attendants and the rest were medical officers and the junior laboratory technicians. Although the accidents reported appeared trivial, it is vital to document them and bring them to the attention of all concerned in the laboratory, in order to prevent major accidents and also because of medico-legal implications. The role of the Laboratory Safety Committee cannot be overemphasised. Modification of staff attitude is considered an important remedial goal.

Stability of Contact Lines in Fluids: 2D Stokes Flow

NASA Astrophysics Data System (ADS)

Guo, Yan; Tice, Ian

2018-02-01

In an effort to study the stability of contact lines in fluids, we consider the dynamics of an incompressible viscous Stokes fluid evolving in a two-dimensional open-top vessel under the influence of gravity. This is a free boundary problem: the interface between the fluid in the vessel and the air above (modeled by a trivial fluid) is free to move and experiences capillary forces. The three-phase interface where the fluid, air, and solid vessel wall meet is known as a contact point, and the angle formed between the free interface and the vessel is called the contact angle. We consider a model of this problem that allows for fully dynamic contact points and angles. We develop a scheme of a priori estimates for the model, which then allow us to show that for initial data sufficiently close to equilibrium, the model admits global solutions that decay to equilibrium exponentially quickly.

LSA silicon material task closed-cycle process development

NASA Technical Reports Server (NTRS)

Roques, R. A.; Wakefield, G. F.; Blocher, J. M., Jr.; Browning, M. F.; Wilson, W.

1979-01-01

The initial effort on feasibility of the closed cycle process was begun with the design of the two major items of untested equipment, the silicon tetrachloride by product converter and the rotary drum reactor for deposition of silicon from trichlorosilane. The design criteria of the initial laboratory equipment included consideration of the reaction chemistry, thermodynamics, and other technical factors. Design and construction of the laboratory equipment was completed. Preliminary silicon tetrachloride conversion experiments confirmed the expected high yield of trichlorosilane, up to 98 percent of theoretical conversion. A preliminary solar-grade polysilicon cost estimate, including capital costs considered extremely conservative, of $6.91/kg supports the potential of this approach to achieve the cost goal. The closed cycle process appears to have a very likely potential to achieve LSA goals.

77 FR 32651 - National Institute of Arthritis and Musculoskeletal and Skin Diseases; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... meetings. The meetings will be closed to the public in accordance with the provisions set forth in sections...). Contact Person: Charles H Washabaugh, Ph.D., Scientific Review Officer, Scientific Review Branch, National... applications. Place: Bethesda Marriott, 5151 Pooks Hill Road, Bethesda, MD 20814. Contact Person: Charles N...

From tunneling to point contact: Correlation between forces and current

NASA Astrophysics Data System (ADS)

Sun, Yan; Mortensen, Henrik; Schär, Sacha; Lucier, Anne-Sophie; Miyahara, Yoichi; Grütter, Peter; Hofer, Werner

2005-05-01

We used a combined ultrahigh vacuum scanning tunneling and atomic force microscope (STM/AFM) to study W tip-Au(111) sample interactions in the regimes from weak coupling to strong interaction and simultaneously measure current changes from picoamperes to microamperes. Close correlation between conductance and interaction forces in a STM configuration was observed. In particular, the electrical and mechanical points of contact are determined based on the observed barrier collapse and adhesive bond formation, respectively. These points of contact, as defined by force and current measurements, coincide within measurement error. Ab initio calculations of the current as a function of distance in the tunneling regime is in quantitative agreement with experimental results. The obtained results are discussed in the context of dissipation in noncontact AFM as well as electrical contact formation in molecular electronics.

Optimal contact definition for reconstruction of Contact Maps

PubMed Central

2010-01-01

Background Contact maps have been extensively used as a simplified representation of protein structures. They capture most important features of a protein's fold, being preferred by a number of researchers for the description and study of protein structures. Inspired by the model's simplicity many groups have dedicated a considerable amount of effort towards contact prediction as a proxy for protein structure prediction. However a contact map's biological interest is subject to the availability of reliable methods for the 3-dimensional reconstruction of the structure. Results We use an implementation of the well-known distance geometry protocol to build realistic protein 3-dimensional models from contact maps, performing an extensive exploration of many of the parameters involved in the reconstruction process. We try to address the questions: a) to what accuracy does a contact map represent its corresponding 3D structure, b) what is the best contact map representation with regard to reconstructability and c) what is the effect of partial or inaccurate contact information on the 3D structure recovery. Our results suggest that contact maps derived from the application of a distance cutoff of 9 to 11Å around the Cβ atoms constitute the most accurate representation of the 3D structure. The reconstruction process does not provide a single solution to the problem but rather an ensemble of conformations that are within 2Å RMSD of the crystal structure and with lower values for the pairwise average ensemble RMSD. Interestingly it is still possible to recover a structure with partial contact information, although wrong contacts can lead to dramatic loss in reconstruction fidelity. Conclusions Thus contact maps represent a valid approximation to the structures with an accuracy comparable to that of experimental methods. The optimal contact definitions constitute key guidelines for methods based on contact maps such as structure prediction through contacts and structural

Automated contact angle estimation for three-dimensional X-ray microtomography data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klise, Katherine A.; Moriarty, Dylan; Yoon, Hongkyu

2015-11-10

Multiphase flow in capillary regimes is a fundamental process in a number of geoscience applications. The ability to accurately define wetting characteristics of porous media can have a large impact on numerical models. In this paper, a newly developed automated three-dimensional contact angle algorithm is described and applied to high-resolution X-ray microtomography data from multiphase bead pack experiments with varying wettability characteristics. The algorithm calculates the contact angle by finding the angle between planes fit to each solid/fluid and fluid/fluid interface in the region surrounding each solid/fluid/fluid contact point. Results show that the algorithm is able to reliably compute contactmore » angles using the experimental data. The in situ contact angles are typically larger than flat surface laboratory measurements using the same material. Furthermore, wetting characteristics in mixed-wet systems also change significantly after displacement cycles.« less

Tibiofemoral contact mechanics after serial medial meniscectomies in the human cadaveric knee.

PubMed

Lee, Stephen J; Aadalen, Kirk J; Malaviya, Prasanna; Lorenz, Eric P; Hayden, Jennifer K; Farr, Jack; Kang, Richard W; Cole, Brian J

2006-08-01

There is no consensus regarding the extent of meniscectomy leading to deleterious effects on tibiofemoral contact mechanics. The meniscus aids in optimizing tibiofemoral contact mechanics, increasing contact area, and decreasing contact stress. Controlled laboratory study. Twelve fresh-frozen human cadaveric knees each underwent 15 separate testing conditions-5 serial 20-mm posterior medial meniscectomy conditions (intact, 50% radial width, 75% radial width, segmental, and total meniscectomy) at 3 flexion angles (0 degrees , 30 degrees , and 60 degrees )-under an 1800-N axial load. Tekscan sensors were used to measure total force and medial force, contact area, mean contact stress, and peak contact stress. All posterior medial meniscectomy conditions resulted in significantly decreased contact areas and increased mean and peak contact stresses compared with the intact state (P < .05). The changes in contact mechanics after segmental and total posterior medial meniscectomies were not statistically different (P > .05). Incremental changes in contact area and mean contact stress increased as more peripheral portions of the medial meniscus were removed, whereas peak contact stresses exhibited similar incremental changes throughout all meniscectomy conditions. The meniscus is a crucial load-bearing structure, optimizing contact area and minimizing contact stress. Loss of hoop tension (ie, segmental meniscectomy) is equivalent to total meniscectomy in load-bearing terms. The peripheral portion of the medial meniscus provides a greater contribution to increasing contact areas and decreasing mean contact stresses than does the central portion, whereas peak contact stresses increase proportionally to the amount of meniscus removed. Because the degree of meniscectomy leading to clinically significant outcomes is unknown, a prudent strategy is to preserve the greatest amount of meniscus possible.

Contact Zone: Missoula

NASA Image and Video Library

2015-07-23

A rock outcrop dubbed "Missoula," near Marias Pass on Mars, is seen in this image mosaic taken by the Mars Hand Lens Imager on NASA's Curiosity rover. Pale mudstone (bottom of outcrop) meets coarser sandstone (top) in this geological contact zone, which has piqued the interest of Mars scientists. White mineral veins that fill fractures in the lower rock unit abruptly end when they meet the upper rock unit. Such clues help scientists understand the possible timing of geological events. First, the fine sediment that now forms the lower unit would have hardened into rock. It then would have fractured, and groundwater would have deposited calcium sulfate minerals into the fractures. Next, the coarser sediment that forms the upper unit would have been deposited. The area pictured is about 16 inches (40 centimeters) across. The image was taken on the 1,031st Martian day, or sol, of the mission (July 1, 2015). MAHLI was built by Malin Space Science Systems, San Diego. NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology in Pasadena, manages the Mars Science Laboratory Project for the NASA Science Mission Directorate, Washington. JPL designed and built the project's Curiosity rover. http://photojournal.jpl.nasa.gov/catalog/PIA19829

Contact angle and local wetting at contact line.

PubMed

Li, Ri; Shan, Yanguang

2012-11-06

This theoretical study was motivated by recent experiments and theoretical work that had suggested the dependence of the static contact angle on the local wetting at the triple-phase contact line. We revisit this topic because the static contact angle as a local wetting parameter is still not widely understood and clearly known. To further clarify the relationship of the static contact angle with wetting, two approaches are applied to derive a general equation for the static contact angle of a droplet on a composite surface composed of heterogeneous components. A global approach based on the free surface energy of a thermodynamic system containing the droplet and solid surface shows the static contact angle as a function of local surface chemistry and local wetting state at the contact line. A local approach, in which only local forces acting on the contact line are considered, results in the same equation. The fact that the local approach agrees with the global approach further demonstrates the static contact angle as a local wetting parameter. Additionally, the study also suggests that the wetting described by the Wenzel and Cassie equations is also the local wetting of the contact line rather than the global wetting of the droplet.

Contact investigation outcomes of Canadian-born adults with tuberculosis in Indigenous and non-Indigenous populations in Alberta.

PubMed

Eisenbeis, Lisa; Gao, Zhiwei; Heffernan, Courtney; Yacoub, Wadieh; Long, Richard; Verma, Geetika

2016-06-27

Contact investigations are a critical component of tuberculosis control in high-income countries. However, the relative success of conventional methods by population group and place of residence is unknown. This study compares outcomes of contact investigations of Canadian-born Indigenous tuberculosis cases living on- and off-reserve with other Canadian-born cases. In a retrospective analysis, Canadian-born adult culture-positive pulmonary TB cases (2001-2010) were identified. Characteristics of source cases and their contacts were compared by population group. Outcomes of contact investigations, including completion of recommended investigations and preventive therapy, were compared in multivariable analysis. Of 171 cases of tuberculosis identified, 49 (29%) were Indigenous on-reserve, 62 (36%) Indigenous off-reserve, and 60 (35%) non-Indigenous or Canadian-born, "other". Indigenous people had more contacts identified per case compared to non-Indigenous patients. Case population group and smear status were the main predictors of the success of contact investigations. Of those recommended preventive therapy, close contacts of Indigenous cases on-reserve had the highest rate of completion, at 54%, vs. 41% and 37% for close contacts of Indigenous living off-reserve and Canadian-born "other" respectively (p = 0.02). Contacts of Indigenous cases living off-reserve had the greatest delay in assessment and the lowest rates of completion of assessment and preventive therapy. In multivariable analysis, population group, smear status of source case and proximity of contact were predictors of preventive therapy acceptance and/or completion. Significant differences in outcomes of contact investigations were observed between population groups. The higher priority of contacts of smear-positive cases appears to influence efficiency of service delivery, regardless of population group. Jurisdictional differences in program delivery, resource availability and perceived risk of

[Sport injuries in full contact and semi-contact karate].

PubMed

Greier, K; Riechelmann, H; Ziemska, J

2014-03-01

Karate enjoys great popularity both in professional and recreational sports and can be classified into full, half and low contact styles. The aim of this study was the analysis of sports injuries in Kyokushinkai (full contact) and traditional Karate (semi-contact). In a retrospective study design, 215 active amateur karateka (114 full contact, 101 semi-contact) were interviewed by means of a standardised questionnaire regarding typical sport injuries during the last 36 months. Injuries were categorised into severity grade I (not requiring medical treatment), grade II (single medical treatment), grade III (several outpatient medical treatments) and grade IV (requiring hospitalisation). In total, 217 injuries were reported in detail. 125 injuries (58%) occurred in full contact and 92 (42%) in semi-contact karate. The time related injury rate of full contact karateka was 1.9/1000 h compared to 1.3/1000 h of semi-contact karateka (p < 0.05). The most common types of injuries were musculoskeletal contusions (33% full contact, 20% semi-contact), followed by articular sprains with 19% and 16%. The lower extremity was affected twice as often in full contact (40%) as in semi-contact (20%) karate. Training injuries were reported by 80% of the full contact and 77% of the semi-contact karateka. Most injuries, both in training and competition, occurred in kumite. 75% of the reported injuries of full contact and 70% of semi-contact karateka were classified as low grade (I or II). The high rate of injuries during training and kumite (sparring) points to specific prevention goals. The emphasis should be put on proprioceptive training and consistent warm-up. In the actual competition the referees play a vital role regarding prevention. © Georg Thieme Verlag KG Stuttgart · New York.

[Costs and prices of laboratory services].

PubMed

Magid, E; Bartels, P D; Brandslund, I; Christensen, M S; Fahrenkrug, J; Hørder, M; Olsen, H; Pedersen, K O; Riber, E

1991-09-23

Cost accounting is performed in private and public laboratories. Guidelines for these activities are required and with this objective in mind, the Board of the Danish Society of Clinical Chemistry commissioned a working group to produce a position paper which is presented now in this report. The report discusses the objectives, the principles and the general requirements for cost accounting. The significance of information on costs for the clinicians' rational use of the laboratory is also illustrated. The working group points out that prerequisites for lucid and appropriate costing guidelines are clarification of which purposes information on costs are meant to serve, identification of the relevant cost centers and quality assurance of laboratory services to a defined extent. It is common practice to express laboratory costs as costs per test. The report advocates calculation of the cost per patient contact, i.e. the overall costs for laboratory service in a given investigative situation.

Novel vertical silicon photodiodes based on salicided polysilicon trenched contacts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaminski, Yelena; TowerJazz Ltd. Migdal Haemek; Shauly, Eitan

2015-12-07

The classical concept of silicon photodiodes comprises of a planar design characterized by heavily doped emitters. Such geometry has low collection efficiency of the photons absorbed close to the surface. An alternative, promising, approach is to use a vertical design. Nevertheless, realization of such design is technologically challenged, hence hardly explored. Herein, a novel type of silicon photodiodes, based on salicided polysilicon trenched contacts, is presented. These contacts can be prepared up to 10 μm in depth, without showing any leakage current associated with the increase in the contact area. Consequently, the trenched photodiodes revealed better performance than no-trench photodiodes. Amore » simple two dimensional model was developed, allowing to estimate the conditions under which a vertical design has the potential to have better performance than that of a planar design. At large, the deeper the trench is, the better is the vertical design relative to the planar (up to 10 μm for silicon). The vertical design is more advantageous for materials characterized by short diffusion lengths of the carriers. Salicided polysilicon trenched contacts open new opportunities for the design of solar cells and image sensors. For example, these contacts may passivate high contact area buried contacts, by virtue of the conformity of polysilicon interlayer, thus lowering the via resistance induced recombination enhancement effect.« less

Putting the Laboratory at the Center of Teaching Chemistry

ERIC Educational Resources Information Center

Bopegedera, A. M. R. P.

2011-01-01

This article describes an effective approach to teaching chemistry by bringing the laboratory to the center of teaching, to bring the excitement of discovery to the learning process. The lectures and laboratories are closely integrated to provide a holistic learning experience. The laboratories progress from verification to open-inquiry and…

Effect of initial contact surface condition on the friction and wear properties of bearing steel in cyclic reciprocating sliding contact

NASA Astrophysics Data System (ADS)

Tanaka, Y.; Endo, M.; Moriyama, S.

2017-05-01

Delamination failure is one of the most important engineering problems. This failure can frequently be detrimental to rolling contact machine elements such as bearings, gear wheels, etc. This phenomenon, called rolling contact fatigue, has a close relationship not only with opening-mode but also with shear-mode fatigue crack growth. The crack face interference is known to significantly affect the shear-mode fatigue crack propagation and its threshold behavior. Quantitative investigation on friction and wear at fatigue crack faces in the material is essentially impossible. Previously, thus, a novel ring-on-ring test by making use of fatigue testing machine was proposed to simulate a cyclic reciprocating sliding contact of crack surfaces. However, this test procedure had some problems. For instance, in order to achieve the uniform contact at the start of test, the rubbing of specimens must be conducted in advance. By this treatment, the specimen surfaces were already damaged before the test. In this study, an improvement of experimental method was made to perform the test using the damage-free specimens. The friction and wear properties for heat-treated high carbon-chromium bearing steel were investigated with this new method and the results were compared to the results obtained by using the initially damaged specimens.

Contact toxicity of 14 insecticides tested on pine butterfly larvae

Treesearch

Robert L. Lyon; Sylvia J. Brown

1971-01-01

Fourteen insecticides were evaluated for contact toxicity to 3rd and 4th stage pine butterfly larvae (Neophasia menapia F. & F.) in a laboratory spray chamber. All candidate insecticides except trichlorfon were more toxic than the standard DDT. The ranking of toxicity at LD90 and toxicity indexes (times more toxic than DDT...

Contact dynamic phenomena in rotating machines: Active/passive considerations

NASA Astrophysics Data System (ADS)

Keogh, Patrick S.

2012-05-01

There are machine operating regimes in which rotor/stator interactions may lead to problematic rotor dynamic behavior. For example, dynamic heat sources arising from seals, bearings and other rubbing stator components may cause rotor thermal bend instability. In active magnetic bearing (AMB) systems, the rotor may experience forward and backward whirl rubs with touchdown bearings (TDBs). In abnormal cases, rotor transient and bounce interactions with such bearings may involve highly localized and short duration contacts. This paper discusses certain contact phenomena that may occur in passive and active systems. For example, the rub induced spiral behavior arises from a combination of unbalance and a thermal input that moves slowly around the rotor, typically in passive rotor-bearing systems. However, the instability can be regarded as if arising from a closed-loop feedback system. Hence it is possible to analyze the phenomenon using techniques that have been developed for active control systems. Rotors levitated by AMBs are truly active, but there are fundamental issues that may arise when contact with TDBs occurs. AMB control and contact interactions are discussed together with the benefits for making the TDB an active element. The reason for this lies in the potential ability to control the contact dynamics and associated mechanical and thermal stresses. A prototype system is described.

Energy - Sandia National Laboratories

Science.gov Websites

; Components Compatibility Hydrogen Behavior Quantitative Risk Assessment Technical Reference for Hydrogen Combustion jbei Facilities Algae Testbed Battery Abuse Testing Laboratory Center for Infrastructure Research and Innovation Combustion Research Facility Joint BioEnergy Institute Close Energy Research Programs

Multi-body Dynamic Contact Analysis Tool for Transmission Design

DTIC Science & Technology

2003-04-01

frequencies were computed in COSMIC NASTRAN, and were validated against the published experimental modal analysis [17]. • Using assumed time domain... modal superposition. • Results from the structural analysis (mode shapes or forced response) were converted into IDEAS universal format (dataset 55...ARMY RESEARCH LABORATORY Multi-body Dynamic Contact Analysis Tool for Transmission Design SBIR Phase II Final Report by

The total laboratory solution: a new laboratory E-business model based on a vertical laboratory meta-network.

PubMed

Friedman, B A

2001-08-01

Major forces are now reshaping all businesses on a global basis, including the healthcare and clinical laboratory industries. One of the major forces at work is information technology (IT), which now provides the opportunity to create a new economic and business model for the clinical laboratory industry based on the creation of an integrated vertical meta-network, referred to here as the "total laboratory solution" (TLS). Participants at the most basic level of such a network would include a hospital-based laboratory, a reference laboratory, a laboratory information system/application service provider/laboratory portal vendor, an in vitro diagnostic manufacturer, and a pharmaceutical/biotechnology manufacturer. It is suggested that each of these participants would add value to the network primarily in its area of core competency. Subvariants of such a network have evolved over recent years, but a TLS comprising all or most of these participants does not exist at this time. Although the TLS, enabled by IT and closely akin to the various e-businesses that are now taking shape, offers many advantages from a theoretical perspective over the current laboratory business model, its success will depend largely on (a) market forces, (b) how the collaborative networks are organized and managed, and (c) whether the network can offer healthcare organizations higher quality testing services at lower cost. If the concept is successful, new demands will be placed on hospital-based laboratory professionals to shift the range of professional services that they offer toward clinical consulting, integration of laboratory information from multiple sources, and laboratory information management. These information management and integration tasks can only increase in complexity in the future as new genomic and proteomics testing modalities are developed and come on-line in clinical laboratories.

The evaluation of shear deformation for contact analysis with large displacement

NASA Astrophysics Data System (ADS)

Nizam, Z. M.; Obiya, H.; Ijima, K.; Azhar, A. T. S.; Hazreek, Z. A. M.; Shaylinda, M. Z. N.

2018-04-01

A common problem encountered in the study of contact problem is the failure to obtain stable and accurate convergence result when the contact node is close to the element edge, which is referred as “critical area”. In previous studies, the modification of the element force equation to apply it to a node-element contact problem using the Euler-Bernoulli beam theory [1]. A simple single-element consists two edges and a contact point was used to simulate contact phenomenon of a plane frame. The modification was proven to be effective by the converge-ability of the unbalanced force at the tip of element edge, which enabled the contact node to “pass-through”, resulting in precise results. However, in another recent study, we discover that, if shear deformation based on Timoshenko beam theory is taken into consideration, a basic simply supported beam coordinate afforded a much simpler and more efficient technique for avoiding the divergence of the unbalanced force in the “critical area”. Using our unique and robust Tangent Stiffness Method, the improved equation can be used to overcome any geometrically nonlinear analyses, including those involving extremely large displacements.

Nest Mosquito Trap quantifies contact rates between nesting birds and mosquitoes.

PubMed

Caillouët, Kevin A; Riggan, Anna E; Rider, Mark; Bulluck, Lesley P

2012-06-01

Accurate estimates of host-vector contact rates are required for precise determination of arbovirus transmission intensity. We designed and tested a novel mosquito collection device, the Nest Mosquito Trap (NMT), to collect mosquitoes as they attempt to feed on unrestrained nesting birds in artificial nest boxes. In the laboratory, the NMT collected nearly one-third of the mosquitoes introduced to the nest boxes. We then used these laboratory data to estimate our capture efficiency of field-collected bird-seeking mosquitoes collected over 66 trap nights. We estimated that 7.5 mosquitoes per trap night attempted to feed on nesting birds in artificial nest boxes. Presence of the NMT did not have a negative effect on avian nest success when compared to occupied nest boxes that were not sampled with the trap. Future studies using the NMT may elucidate the role of nestlings in arbovirus transmission and further refine estimates of nesting bird and vector contact rates. © 2012 The Society for Vector Ecology.

Nest Mosquito Trap quantifies contact rates between nesting birds and mosquitoes

PubMed Central

Caillouët, Kevin A.; Riggan, Anna E.; Rider, Mark; Bulluck, Lesley P.

2012-01-01

Accurate estimates of host-vector contact rates are required for precise determination of arbovirus transmission intensity. We designed and tested a novel mosquito collection device, the Nest Mosquito Trap (NMT), to collect mosquitoes as they attempt to feed on unrestrained nesting birds in artificial nest boxes. In the laboratory, the NMT collected nearly one-third of the mosquitoes introduced to the nest boxes. We then used these laboratory data to estimate our capture efficiency of field-collected bird-seeking mosquitoes collected over 66 trap nights. We estimated that 7.5 mosquitoes per trap night attempted to feed on nesting birds in artificial nest boxes. Presence of the NMT did not have a negative effect on avian nest success when compared to occupied nest boxes that were not sampled with the trap. Future studies using the NMT may elucidate the role of nestlings in arbovirus transmission and further refine estimates of nesting bird and vector contact rates. PMID:22548555

Contact Allergy to (Ingredients of) Toothpastes.

PubMed

de Groot, Anton

The literature on contact allergy to (ingredients of) toothpastes is critically reviewed. We have found 47 case reports, small case series (n = 2-5) and citations published between 1900 and 2016 describing more than 60 patients allergic to toothpastes, and in addition 3 larger case series and many descriptions of toothpaste allergy among selected groups of patients. Allergic reactions usually manifest as cheilitis with or without dermatitis around the mouth, less frequently by oral symptoms. Formerly, many reactions were caused by cinnamon derivatives; more recently, reported allergens are diverse. A semiopen test or closed patch test with the toothpaste "as is" may be performed as an initial test, but a positive reaction should always be followed by confirmatory tests. The role of contact allergy to toothpastes in patients with oral symptoms (stomatitis, glossitis, gingivitis, buccal mucositis, burning, soreness, and possibly burning mouth syndrome and recurrent aphthous ulcers) is unclear and should be further investigated.

Air Force Research Laboratory Spacecraft Cryocooler Endurance Evaluation Facility Closing Report

NASA Astrophysics Data System (ADS)

Armstrong, J.; Martin, K. W.; Fraser, T.

2015-12-01

The Air Force Research Laboratory (AFRL) Spacecraft Component Thermal Research Group has been devoted to evaluating lifetime performance of space cryocooler technology for over twenty years. Long-life data is essential for confirming design lifetimes for space cryocoolers. Continuous operation in a simulated space environment is the only accepted method to test for degradation. AFRL has provided raw data and detailed evaluations to cryocooler developers for advancing the technology, correcting discovered deficiencies, and improving cryocooler designs. At AFRL, units of varying design and refrigeration cycles were instrumented in state-of-the-art experiment stands to provide spacelike conditions and were equipped with software data acquisition to track critical cryocooler operating parameters. This data allowed an assessment of the technology's ability to meet the desired lifetime and documented any long-term changes in performance. This paper will outline a final report of the various flight cryocoolers tested in our laboratory. The data summarized includes the seven cryocoolers tested during 2014-2015. These seven coolers have a combined total of 433,326 hours (49.5 years) of operation.

Imaging surface contacts: Power law contact distributions and contact stresses in quartz, calcite, glass and acrylic plastic

USGS Publications Warehouse

Dieterich, J.H.; Kilgore, B.D.

1996-01-01

A procedure has been developed to obtain microscope images of regions of contact between roughened surfaces of transparent materials, while the surfaces are subjected to static loads or undergoing frictional slip. Static loading experiments with quartz, calcite, soda-lime glass and acrylic plastic at normal stresses to 30 MPa yield power law distributions of contact areas from the smallest contacts that can be resolved (3.5 ??m2) up to a limiting size that correlates with the grain size of the abrasive grit used to roughen the surfaces. In each material, increasing normal stress results in a roughly linear increase of the real area of contact. Mechanisms of contact area increase are by growth of existing contacts, coalescence of contacts and appearance of new contacts. Mean contacts stresses are consistent with the indentation strength of each material. Contact size distributions are insensitive to normal stress indicating that the increase of contact area is approximately self-similar. The contact images and contact distributions are modeled using simulations of surfaces with random fractal topographies. The contact process for model fractal surfaces is represented by the simple expedient of removing material at regions where surface irregularities overlap. Synthetic contact images created by this approach reproduce observed characteristics of the contacts and demonstrate that the exponent in the power law distributions depends on the scaling exponent used to generate the surface topography.

Comparative study of antibacterial and antifungal effects of rigid gas permeable contact lens disinfecting solutions.

PubMed

Kuzman, Tomislav; Kutija, Marija Barisić; Kordić, Rajko; Popović-Sui, Smiljka; Jandroković, Sonja; Skegro, Ivan; Pokupec, Rajko

2013-04-01

The aim of this study was to compare antimicrobial efficacy of rigid contact lens disinfecting solutions. We tested five commercially available solutions: Unique pH (Alcon Laboratories), Boston Advance (Polymer Technology Corp.), Nitilens Conditioner GP (Avizor), Total Care (AMO), Boston Simplus (Bausch&Lomb). Their efficacy to disinfect saline solution experimentally contaminated with American Type Culture Collection (ATCC): Staphylococcus aureus (ATCC 25923), Escherichia coli (ATCC 25922), Pseudomonas aeruginosa (ATCC 27853), Candida albicans (ATCC 90028) and Staphylococcus epidermidis (isolated from our laboratory) was tested. All tested solutions reduced concentrations of bacteria and fungi below 1000 CFU/mL (Colony forming unit; reduction by 3 log and 1 log, respectively) after the 8 hours period. Overall, all contact lens care solutions showed good disinfecting activity against tested bacteria and fungi, with more variation in their antifungal than in antibacterial efficacy. Results of our study might be valuable when selecting appropriate solutions for non-compliant contact lens wearers.

Index to Benet Laboratories Technical Reports - 1988

DTIC Science & Technology

1989-05-01

EDITING SECTION MAY 1989 US ARMY ARMAMENT RESEARCH , ~ DEVELOPMENT AND ENGINEERING CENTER CLOSE COMBAT ARMAMENTS CENTER BENET LABORATORIES WATERVLIET, N.Y...Watervliet, NY 12189-4050 I =ONTROLLING OFFICE NAME AND ADoRESS 12. REPORT DATE US Army Armament Research , Develop, & Engr Center April 1988 Close Combat...Watervliet, NY 12189-4050 11. CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE US Army ARDEC May 1989 Close Combat Armaments Center 13. NUMBER OF PAGES

Molecular Characterization of Staphylococcus aureus Isolated from Bovine Mastitis and Close Human Contacts in South African Dairy Herds: Genetic Diversity and Inter-Species Host Transmission

PubMed Central

Schmidt, Tracy; Kock, Marleen M.; Ehlers, Marthie M.

2017-01-01

Staphylococcus aureus is one of the most common etiological agents of contagious bovine mastitis worldwide. The purpose of this study was to genetically characterize a collection of S. aureus isolates (bovine = 146, human = 12) recovered from cases of bovine mastitis and nasal swabs of close human contacts in the dairy environment. Isolates were screened for a combination of clinically significant antimicrobial and virulence gene markers whilst the molecular epidemiology of these isolates and possible inter-species host transmission was investigated using a combination of genotyping techniques. None of the isolates under evaluation tested positive for methicillin or vancomycin resistance encoding genes. Twenty seven percent of the bovine S. aureus isolates tested positive for one or more of the pyrogenic toxin superantigen (PTSAg) genes with the sec and sell genes predominating. Comparatively, 83% of the human S. aureus isolates tested positive for one or more PTSAg genes with a greater variety of genes being detected. Genomic DNA macrorestriction followed by pulsed-field gel electrophoresis (PFGE) of the bovine isolates generated 58 electrophoretic patterns which grouped into 10 pulsotypes at an 80% similarity level. The majority of the bovine isolates, 93.2% (136/146), clustered into four major pulsotypes. Seven sequence types (ST) were identified among the representative bovine S. aureus isolates genotyped, including: ST8 (CC8), ST97 (CC97), ST351 (CC705), ST352 (CC97), ST508 (CC45), ST2992 (CC97) and a novel sequence type, ST3538 (CC97). Based on PFGE analysis, greater genetic diversity was observed among the human S. aureus isolates. Bovine and human isolates from three sampling sites clustered together and were genotypically indistinguishable. Two of the isolates, ST97 and ST352 belong to the common bovine lineage CC97, and their isolation from close human contacts suggests zoonotic transfer. In the context of this study, the third isolate, ST8 (CC8), is

Crop yield and light / energy efficiency in a closed ecological system: two laboratory biosphere experiments

NASA Astrophysics Data System (ADS)

Nelson, M.; Dempster, W. F.; Silverstone, S.; Alling, A.; Allen, J. P.; van Thillo, M.

Two crop growth experiments in the soil-based closed ecological facity, Laboratory Biosphere, were conducted from 2003-2004 with candidate space life support crops. Apogee wheat (Utah State University variety) was grown, planted in 2 densities, 400 and 800 seeds m-2. The lighting regime for the wheat crop was 16 hours of light -- 8 hours dark at a total light intensity of around 840 mol m2 sec-1 and 48.4 mol m-2 d-1 over 84 days Average biomass was 1395 g m-2, 16.0 g m-2 day-1 and average seed production was 689 g m-2 and 7.9 g m2 day-1. The less densely planted side was more productive than the denser planting, with 1634 g m-2 and 18.8g m-2 day-1 of biomass vs. 1156 g m-2 and 13.3 g m-2 day-1; and a seed harvest of 812.3 g m-2 and 9.3 g m-2 day-1 vs. 566.5 g m-2 and 6.5 g m-2 day-1 Harvest index was 0.49 for the wheat crop. The experiment with sweet potato used TU-82-155, a compact variety developed at Tuskegee University. Light during the sweet potato experiment, on a 16 hour on/8 hours dark cycle, totalled 5568 total moles of light in 126 days for the sweet potatoes, or an average of 44.2 moles m-2 day-1. Temperature regime was 28 deg +/- 3 deg C day /22 deg +/- 4 deg C night. Sweet potato tuber yield was 39.7 kg wet weight, or an average of 7.4 kg m-2 and 7.7 kg dry weight of tubers since dry weight was about 18.6% wet weight.^Average per day production was 58.7 g m-2 day-1 wet weight and 11.3 g m-2 day-1. For the wheat, average light efficiency was 0.34 grams biomass per mole, and 0.17 grams seed per mole. The best area of wheat had an efficiency of light utilization of 0.51 g biomass per mole and 0.22 g seed per mole. For the sweet potato crop, light efficiency per tuber wet weight was 7.13 g/mole and 1.38 g dry weight of tuber per mole of light. The best area of tuber production had 9.49 g/mole wet weight and 1.85 g/mole of light dry weight. Production from the wheat was The Laboratory Biosphere experiment's light efficiency was somewhat higher than the USU

Adult meerkats modify close call rate in the presence of pups.

PubMed

Wyman, Megan T; Rivers, Pearl R; Muller, Coline; Toni, Pauline; Manser, Marta B

2017-06-01

In animals, signaling behavior is often context-dependent, with variation in the probability of emitting certain signals dependent on fitness advantages. Senders may adjust signaling rate depending on receiver identity, presence of audiences, or noise masking the signal, all of which can affect the benefits and costs of signal production. In the cooperative breeding meerkat Suricata suricatta , group members emit soft contact calls, termed as "close calls", while foraging in order to maintain group cohesion. Here, we investigated how the close calling rate during foraging was affected by the presence of pups, that produce continuous, noisy begging calls as they follow older group members. Adults decreased their overall close call rate substantially when pups were foraging with the group in comparison to periods when no pups were present. We suggest this decrease was likely due to a masking effect of the loud begging calls, which makes the close call function of maintaining group cohesion partly redundant as the centrally located begging calls can be used instead to maintain cohesion. There was some support that adults use close calls strategically to attract specific pups based on fitness advantages, that is, as the philopatric sex, females should call more than males and more to female pups than male pups. Dominant females called more than dominant males when a pup was in close proximity, while subordinates showed no sex-based differences. The sex of the nearest pup did not affect the calling rate of adults. The study shows that meerkats modify their close call production depending on benefits gained from calling and provides an example of the flexible use of one calling system in the presence of another, here contact calls versus begging calls, within the same species.

High-frequency imaging of elastic contrast and contact area with implications for naturally observed changes in fault properties

USGS Publications Warehouse

Nagata, Kohei; Kilgore, Brian D.; Beeler, Nicholas M.; Nakatani, Masao

2014-01-01

During localized slip of a laboratory fault we simultaneously measure the contact area and the dynamic fault normal elastic stiffness. One objective is to determine conditions where stiffness may be used to infer changes in area of contact during sliding on nontransparent fault surfaces. Slip speeds between 0.01 and 10 µm/s and normal stresses between 1 and 2.5 MPa were imposed during velocity step, normal stress step, and slide-hold-slide tests. Stiffness and contact area have a linear interdependence during rate stepping tests and during the hold portion of slide-hold-slide tests. So long as linearity holds, measured fault stiffness can be used on nontransparent materials to infer changes in contact area. However, there are conditions where relations between contact area and stiffness are nonlinear and nonunique. A second objective is to make comparisons between the laboratory- and field-measured changes in fault properties. Time-dependent changes in fault zone normal stiffness made in stress relaxation tests imply postseismic wave speed changes on the order of 0.3% to 0.8% per year in the two or more years following an earthquake; these are smaller than postseismic increases seen within natural damage zones. Based on scaling of the experimental observations, natural postseismic fault normal contraction could be accommodated within a few decimeter wide fault core. Changes in the stiffness of laboratory shear zones exceed 10% per decade and might be detectable in the field postseismically.

Contact urticaria, allergic contact dermatitis, and photoallergic contact dermatitis from oxybenzone.

PubMed

Landers, Maeran; Law, Sandra; Storrs, Frances J

2003-03-01

There is little literature regarding conventional patch tests and photopatch tests to oxybenzone resulting in both immediate- and delayed-type hypersensitivity reactions. A patient was patch-tested and photopatch-tested to various sunscreen chemicals. Both immediate- and delayed-type hypersensitivity reactions were observed with oxybenzone. The positive patch tests were also photoaccentuated. Oxybenzone, a common sunscreen allergen, can result in both contact urticaria and delayed-type hypersensitivity on both conventional patch testing and photopatch testing. Allergic contact dermatitis to sunscreen chemicals has traditionally included contact urticaria, allergic contact dermatitis, and photoallergic contact dermatitis. Due to the recognition of p-aminobenzoic acid (PABA) and its esters as sensitizers, the presence of benzophenones in "PABA-free" sunscreens has become more prevalent, especially in sunscreens with a sun protection factor (SPF) greater than 8. In our patient, immediate- and delayed-type hypersensitivity reactions were seen to oxybenzone (2-hydroxy-4-methoxybenzophenone, 2-benzoyl-5-methoxyphenol, benzophenone-3, Eusolex 4360, Escalol 567, EUSORB 228, Spectra-Sorb UV-9, Uvinul M-40) upon conventional patch testing and photopatch testing.

Linking Microstructural Evolution and Tribology in Metallic Contacts

NASA Astrophysics Data System (ADS)

Chandross, Michael; Cheng, Shengfeng; Argibay, Nicolas

Tribologists rely on phenomenological models to describe the seemingly disjointed steady-state regimes of metal wear. Pure metals such as gold - frequently used in electrical contacts - exhibit high friction and wear. In contrast, nanocrystalline metals often show much lower friction and wear. The engineering community has generally used a phenomenological connection between hardness and friction/wear to explain this macroscale response and guide designs. We present results of recent simulations and experiments that demonstrate a general framework for connecting materials properties (i.e. microstructural evolution) to tribological response. We present evidence that competition between grain refinement (from cold working), grain coarsening (from stress-induced grain growth), and wear (delamination and plowing) can be used to describe transient and steady state tribological behavior of metals, alloys and composites. We explore the seemingly disjointed steady-state friction regimes of metals and alloys, with a goal of elucidating the structure-property relationships, allowing for the engineering of tribological materials and contacts based on the kinetics of grain boundary motion. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Calgary Laboratory Services

PubMed Central

2015-01-01

Calgary Laboratory Services provides global hospital and community laboratory services for Calgary and surrounding areas (population 1.4 million) and global academic support for the University of Calgary Cumming School of Medicine. It developed rapidly after the Alberta Provincial Government implemented an austerity program to address rising health care costs and to address Alberta’s debt and deficit in 1994. Over roughly the next year, all hospital and community laboratory test funding within the province was put into a single budget, fee codes for fee-for-service test billing were closed, roughly 40% of the provincial laboratory budget was cut, and roughly 40% of the pathologists left the province of Alberta. In Calgary, in the face of these abrupt changes in the laboratory environment, private laboratories, publicly funded hospital laboratories and the medical school department precipitously and reluctantly merged in 1996. The origin of Calgary Laboratory Services was likened to an “unhappy shotgun marriage” by all parties. Although such a structure could save money by eliminating duplicated services and excess capacity and could provide excellent city-wide clinical service by increasing standardization, it was less clear whether it could provide strong academic support for a medical school. Over the past decade, iterations of the Calgary Laboratory Services model have been implemented or are being considered in other Canadian jurisdictions. This case study analyzes the evolution of Calgary Laboratory Services, provides a metric-based review of academic performance over time, and demonstrates that this model, essentially arising as an unplanned experiment, has merit within a Canadian health care context. PMID:28725754

Disorders of Arousal From Sleep and Violent Behavior: The Role of Physical Contact and Proximity

PubMed Central

Pressman, Mark R.

2007-01-01

Study Objectives: To review medical and legal case reports to determine how many appear to support the belief that violence against other individuals that occurs during Disorders of Arousal - sleepwalking, confusional arousal, and sleep terrors – is triggered by direct physical contact or close proximity to that individual and does not occur randomly or spontaneously. Design: Historical review of case reports in the medical and legal literature. Measurements and Results: A total of 32 cases drawn from medical and legal literature were reviewed. Each case contained a record of violence associated with Disorders of Arousal; in each, details of the violent behavior were available. Violent behaviors associated with provocations and/or close proximity were found to be present in 100% of confusional arousal patients and 81% of sleep terror patients. Violent behaviors were associated with provocation or close proximity in 40%–90% of sleepwalking cases, depending on whether the legal verdict and other factors were taken into account. Often the provocation was quite minor and the response greatly exaggerated. The specific manner in which the violence was triggered differed among sleepwalking, confusional arousals, and sleep terrors. Conclusions: In the cases reviewed, violent behavior directed against other individuals associated with Disorders of Arousal most frequently appeared to follow direct provocation by, or close proximity to, another individual. Sleepwalkers most often did not seek out victims, but rather the victims sought out or encountered the sleepwalker. These conclusions are tempered by several limitations: the selection of cases was not random and may not represent an accurate sample of violent behaviors associated with Disorders of Arousal. Also, final verdicts by juries in reported legal cases should not be confused with scientific proof of the presence or absence of sleepwalking. The pathophysiology of Disorders of Arousal with and without violent

Electron transport in extended carbon-nanotube/metal contacts: Ab initio based Green function method

NASA Astrophysics Data System (ADS)

Fediai, Artem; Ryndyk, Dmitry A.; Cuniberti, Gianaurelio

2015-04-01

We have developed a new method that is able to predict the electrical properties of the source and drain contacts in realistic carbon nanotube field effect transistors (CNTFETs). It is based on large-scale ab initio calculations combined with a Green function approach. For the first time, both internal and external parts of a realistic CNT-metal contact are taken into account at the ab initio level. We have developed the procedure allowing direct calculation of the self-energy for an extended contact. Within the method, it is possible to calculate the transmission coefficient through a contact of both finite and infinite length; the local density of states can be determined in both free and embedded CNT segments. We found perfect agreement with the experimental data for Pd and Al contacts. We have explained why CNTFETs with Pd electrodes are p -type FETs with ohmic contacts, which can carry current close to the ballistic limit (provided contact length is large enough), whereas in CNT-Al contacts transmission is suppressed to a significant extent, especially for holes.

[Ulcerative contact dermitis caused by premixed concrete (cement burns)].

PubMed

Ancona Alayón; Aranda Martínez, J G

1978-01-01

Cement dermatitis manifests clinically as a chronic dermatitis of irritative character, due to its alkaline nature and as allergic contact dermatitis produced by sensitization to chromium and cobalt occurring as trace elements. the present report deals with a mason without previous dermatitis, presenting bullae, ulcers and necrosis in lower limbs, short time after incidental contact at work, with premixed concrete. The clinical manifestations, such as short evolution, clear limitation to sites in close contact with concrete, negativity to standard patch testing and good prognosis with early treatment, are mentioned. The acute irritant nature of the disease is clear, in opposition to the classical manifestations of cement dermatitis. The need of studies of the chemical properties of this material including pH, alkalinity and the possible roll of additives employed, is part of the strategy for prevention of occupational dermatitis in the building trade, which should include also, information of hazards and proper training in their trade.

Space life sciences: closed ecological systems: earth and space applications.

PubMed

2005-01-01

This issue contains peer-reviewed papers from a workshop on Closed Ecological Systems: Earth and Space Applications at the 35th COSPAR General Assembly in Paris, France, convened in July 2004. The contributions reflected the wide range of international work in the field, especially Europe, Russia, Japan, and the United States. The papers are arranged according to four main themes: 1) Methods of evaluation and theory of closed ecological systems; 2) Reports from recent experiments in closed ecological system facilities; 3) Bioregenerative technologies to advance degree of closure and cycling; and 4) Laboratory studies of small closed ecological systems.

75 FR 68330 - Closed Meeting of the Threat Reduction Advisory Committee

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-05

... DEPARTMENT OF DEFENSE Office of the Secretary Closed Meeting of the Threat Reduction Advisory... advisory committee meeting of the Threat Reduction Advisory Committee (Hereafter referred to as ``the...: Contact Mr. Eric Wright, Defense Threat Reduction Agency/AST, 8725 John J. Kingman Road, MS 6201, Fort...

A closed recirculated sea-water system

USGS Publications Warehouse

1967-01-01

Study of a virus disease in the chinook salmon (Oncorhynchus tshawytscha) necessitated the use of a marine environment to study the long range effects of the disease and to complete the life cycle of its etiologic agent. A closed recirculated sea-water system was designed for use under experimental laboratory conditions so that controlled studies of the disease could be made. As others may wish to do marine environment studies in the laboratory, the design and operation of our system are presented. Other systems currently in use have been described by Chin (1959), DeWitt and Salo (1960), McCrimmon and Berst (1966), and the authors of collected papers edited by Clark and Clark (1964). Preparatory to the design and construction of the system in use in this laboratory, visits were made to marine systems in use at the University of Washington's College of Fisheries, Seattle, -washington, and Friday Harbor Laboratory, San Juan Island, Washington; the Washington State Department of Fisheries' Point whitney Shellfish Laboratory, Brinnon, Washington; Humboldt State College, Arcata, California; and the Steinhart Aquarium of the California Academy of Science, San Francisco, California.

Slit-lamp management in contact lenses laboratory classes: learning upgrade with monitor visualization of webcam video recordings

NASA Astrophysics Data System (ADS)

Arines, Justo; Gargallo, Ana

2014-07-01

The training in the use of the slit lamp has always been difficult for students of the degree in Optics and Optometry. Instruments with associated cameras helps a lot in this task, they allow teachers to observe and control if the students evaluate the eye health appropriately, correct use errors and show them how to do it with a visual demonstration. However, these devices are more expensive than those that do not have an integrated camera connected to a display unit. With the aim to improve students' skills in the management of slit lamp, we have adapted USB HD webcams (Microsoft Lifecam HD-5000) to the objectives of the slit lamps available in our contact lenses laboratory room. The webcams are connected to a PC running Linux Ubuntu 11.0; therefore that is a low-cost device. Our experience shows that single method has several advantages. It allows us to take pictures with a good quality of different conditions of the eye health; we can record videos of eye evaluation and make demonstrations of the instrument. Besides it increases the interactions between students because they could see what their colleagues are doing and take conscious of the mistakes, helping and correcting each others. It is a useful tool in the practical exam too. We think that the method supports the training in optometry practice and increase the students' confidence without a huge outlay.

Intergroup Contact and Outgroup Humanization: Is the Causal Relationship Uni- or Bidirectional?

PubMed

Capozza, Dora; Di Bernardo, Gian Antonio; Falvo, Rossella

2017-01-01

The attribution of uniquely human characteristics to the outgroup may favor the search for contact with outgroup members and, vice versa, contact experiences may improve humanity attributions to the outgroup. To explore this bidirectional relationship, two studies were performed. In Study 1, humanity perceptions were manipulated using subliminal conditioning. Two experimental conditions were created. In the humanization condition, the unconditioned stimuli (US) were uniquely human words; in the dehumanization condition, the US were non-uniquely human and animal words. In both conditions, conditioned stimuli were typical outgroup faces. An approach/avoidance technique (the manikin task) was used to measure the willingness to have contact with outgroup members. Findings showed that in the humanization condition participants were faster in approaching than in avoiding outgroup members: closeness to the outgroup was preferred to distance. Latencies of approach and avoidance movements were not different in the dehumanization condition. In Study 2, contact was manipulated using the manikin task. One approach (contact) condition and two control conditions were created. The attribution of uniquely human traits to the outgroup was stronger in the contact than in the no-contact conditions. Furthermore, the effect of contact on humanity attributions was mediated by increased trust toward the outgroup. Thus, findings demonstrate the bidirectionality of the relationship between contact and humanity attributions. Practical implications of findings are discussed.

Augmented Reality for Close Quarters Combat

ScienceCinema

None

2018-01-16

Sandia National Laboratories has developed a state-of-the-art augmented reality training system for close-quarters combat (CQB). This system uses a wearable augmented reality system to place the user in a real environment while engaging enemy combatants in virtual space (Boston Dynamics DI-Guy). Umbra modeling and simulation environment is used to integrate and control the AR system.

An elastic-plastic contact model for line contact structures

NASA Astrophysics Data System (ADS)

Zhu, Haibin; Zhao, Yingtao; He, Zhifeng; Zhang, Ruinan; Ma, Shaopeng

2018-06-01

Although numerical simulation tools are now very powerful, the development of analytical models is very important for the prediction of the mechanical behaviour of line contact structures for deeply understanding contact problems and engineering applications. For the line contact structures widely used in the engineering field, few analytical models are available for predicting the mechanical behaviour when the structures deform plastically, as the classic Hertz's theory would be invalid. Thus, the present study proposed an elastic-plastic model for line contact structures based on the understanding of the yield mechanism. A mathematical expression describing the global relationship between load history and contact width evolution of line contact structures was obtained. The proposed model was verified through an actual line contact test and a corresponding numerical simulation. The results confirmed that this model can be used to accurately predict the elastic-plastic mechanical behaviour of a line contact structure.

Physical distance, genetic relationship, age, and leprosy classification are independent risk factors for leprosy in contacts of patients with leprosy.

PubMed

Moet, F Johannes; Pahan, David; Schuring, Ron P; Oskam, Linda; Richardus, Jan H

2006-02-01

Close contacts of patients with leprosy have a higher risk of developing leprosy. Several risk factors have been identified, including genetic relationship and physical distance. Their independent contributions to the risk of developing leprosy, however, have never been sufficiently quantified. Logistic-regression analysis was performed on intake data from a prospective cohort study of 1037 patients newly diagnosed as having leprosy and their 21,870 contacts. Higher age showed an increased risk, with a bimodal distribution. Contacts of patients with paucibacillary (PB) leprosy with 2-5 lesions (PB2-5) and those with multibacillary (MB) leprosy had a higher risk than did contacts of patients with single-lesion PB leprosy. The core household group had a higher risk than other contacts living under the same roof and next-door neighbors, who again had a higher risk than neighbors of neighbors. A close genetic relationship indicated an increased risk when blood-related children, parents, and siblings were pooled together. Age of the contact, the disease classification of the index patient, and physical and genetic distance were independently associated with the risk of a contact acquiring leprosy. Contact surveys in leprosy should be not only focused on household contacts but also extended to neighbors and consanguineous relatives, especially when the patient has PB2-5 or MB leprosy.

Tibiofemoral joint contact area and pressure after single- and double-bundle anterior cruciate ligament reconstruction.

PubMed

Morimoto, Yusuke; Ferretti, Mario; Ekdahl, Max; Smolinski, Patrick; Fu, Freddie H

2009-01-01

The purpose of this study was to compare the tibiofemoral contact area and pressure after single-bundle (SB) and double-bundle (DB) anterior cruciate ligament (ACL) reconstruction by use of 2 femoral and 2 tibial tunnels in intact cadaveric knees. Tibiofemoral contact area and mean and maximum pressures were measured by pressure-sensitive film (Fujifilm, Valhalla, NY) inserted between the tibia and femur. The knee was subjected to a 1,000-N axial load by use of a uniaxial testing machine at 0 degrees , 15 degrees , 30 degrees , and 45 degrees of flexion. Three conditions were evaluated: (1) intact ACL, (2) SB ACL reconstruction (n = 10 knees), and (3) DB ACL reconstruction (n = 9 knees). When compared with the intact knee, DB ACL reconstruction showed no significant difference in tibiofemoral contact area and mean and maximum pressures. SB ACL reconstruction had a significantly smaller contact area on the lateral and medial tibiofemoral joints at 30 degrees and 15 degrees of flexion. SB ACL reconstruction also had significantly higher mean pressures at 15 degrees of flexion on the medial tibiofemoral joint and at 0 degrees and 15 degrees of flexion on the lateral tibiofemoral joint, as well as significantly higher maximum pressures at 15 degrees of flexion on the lateral tibiofemoral joint. SB ACL reconstruction resulted in a significantly smaller tibiofemoral contact area and higher pressures. DB ACL more closely restores the normal contact area and pressure mainly at low flexion angles. Our findings suggest that the changes in the contact area and pressures after SB ACL reconstruction may be one of the causes of osteoarthritis on long-term follow-up. DB ACL reconstruction may reduce the incidence of osteoarthritis by closely restoring contact area and pressure.

Closed dressings after laser skin resurfacing.

PubMed

Newman, J P; Koch, R J; Goode, R L

1998-07-01

To evaluate the safety, efficacy, and patient acceptance of closed dressings after full facial resurfacing with the carbon dioxide laser. Prospective cohort of men and women undergoing full facial carbon dioxide laser resurfacing. Ambulatory surgical center at a university hospital. Forty consecutive patients randomized to 1 of 4 dressing groups. All patients underwent full facial resurfacing with a carbon dioxide laser system. One of 5 closed dressings (single- or 3-layer composite foam, plastic mesh, hydrogel, or polymer film) was placed immediately after the procedure. Closed dressings were changed on postoperative day 2 and removed on postoperative day 4. Objective postoperative criteria of erythema, scarring, reepithelialization, and surface irregularities were recorded and photodocumented. Comparisons were made among the closed dressing groups as well as with a group of historical control subjects treated with open dressings. The ease of application, office time for preparation and application, and cost of the individual dressings were collected. Patient characteristics of overall acceptance, comfort, and ease of maintenance were recorded with a visual analog scale. There were no complications of scarring, surface irregularities, or contact dermatitis from the application or maintenance of the closed dressings. There were no significant differences in the number of days of postoperative erythema or in the rate of facial reepithelialization among the groups. Most patients preferred not to continue with the closed dressings past 2 days. Positive features from the use of closed dressings included reduction in crust formation, decreased pruritus, decreased erythema, and decreased postoperative pain, compared with historical controls. Negative features included time in preparation and application of the dressings. Costs ranged from $9.79 to $50 per dressing change. Closed dressings are safe and offer benefits noted during the first 4 postoperative days. Patients

Equilibrium contact angle or the most-stable contact angle?

PubMed

Montes Ruiz-Cabello, F J; Rodríguez-Valverde, M A; Cabrerizo-Vílchez, M A

2014-04-01

It is well-established that the equilibrium contact angle in a thermodynamic framework is an "unattainable" contact angle. Instead, the most-stable contact angle obtained from mechanical stimuli of the system is indeed experimentally accessible. Monitoring the susceptibility of a sessile drop to a mechanical stimulus enables to identify the most stable drop configuration within the practical range of contact angle hysteresis. Two different stimuli may be used with sessile drops: mechanical vibration and tilting. The most stable drop against vibration should reveal the changeless contact angle but against the gravity force, it should reveal the highest resistance to slide down. After the corresponding mechanical stimulus, once the excited drop configuration is examined, the focus will be on the contact angle of the initial drop configuration. This methodology needs to map significantly the static drop configurations with different stable contact angles. The most-stable contact angle, together with the advancing and receding contact angles, completes the description of physically realizable configurations of a solid-liquid system. Since the most-stable contact angle is energetically significant, it may be used in the Wenzel, Cassie or Cassie-Baxter equations accordingly or for the surface energy evaluation. © 2013 Elsevier B.V. All rights reserved.

Burkholderia thailandensis: Growth and Laboratory Maintenance.

PubMed

Garcia, Erin C; Cotter, Peggy A

2016-08-12

Burkholderia thailandensis is a nonpathogenic Gram-negative bacterium found in tropical soils. Closely related to several human pathogens, its ease of genetic manipulation, rapid growth in the laboratory, and low virulence make B. thailandensis a commonly used model organism. This unit describes the fundamental protocols for in vitro growth and maintenance of B. thailandensis in the laboratory. © 2016 by John Wiley & Sons, Inc. Copyright © 2016 John Wiley & Sons, Inc.

An Examination of Career Satisfaction for Medical Laboratory Professionals Using Wlodkowski's Motivational Framework

ERIC Educational Resources Information Center

Kenwright, Kathleen M.

2016-01-01

Medical laboratory science professionals are healthcare practitioners who provide laboratory data that aids in the diagnosis, treatment, and prevention of disease. However, there is a large shortage of these professionals who perform the laboratory tests behind the scenes with very minimal patient contact. The purpose of this research was to…

Stokes flow inside an evaporating liquid line for any contact angle

NASA Astrophysics Data System (ADS)

Petsi, A. J.; Burganos, V. N.

2008-09-01

Evaporation of droplets or liquid films lying on a substrate induces internal viscous flow, which affects the transport of suspended particles and, thus, the final deposit profile in numerous applications. In this work, the problem of Stokes flow inside a two-dimensional droplet, representing the cross section of an evaporating liquid line lying on a flat surface, is considered. The stream function formulation is adopted, leading to the biharmonic equation in bipolar coordinates. A solution in closed form is obtained for any contact angle in (0,π) and is, thus, valid for both hydrophilic and hydrophobic substrates. The solution can be used with any type of evaporation mechanism, including diffusion, convection, or kinetically controlled modes. Both pinned and depinned contact lines are considered. For the boundary conditions to be compatible at the contact lines, the Navier slip boundary condition is applied on the substrate. Numerical results are presented for kinetically and diffusion controlled evaporation. For pinned contact lines, the flow inside the evaporating liquid line is directed towards the edges, thus, promoting the coffee stain phenomenon. In the case of depinned contact lines and contact angle less than π/2 , the flow is directed towards the center of the droplet, whereas, for strongly hydrophobic substrates it is directed outwards.

Contact formation during fibroblast locomotion: involvement of membrane ruffles and microtubules

PubMed Central

1988-01-01

We have correlated the motility of the leading edge of fibroblasts, monitored by phase-contrast cinematography, with the relative distributions of several cytoskeletal elements (vinculin, tubulin, and actin) as well as with the contact patterns determined by interference reflection microscopy. This analysis has revealed the involvement of both ruffles and microspikes, as well as microtubules in the initiation of focal contact formation. Nascent vinculin sites within the leading edge or at its base, taken as primordial cell-substrate contacts, were invariably colocalized with sites that showed a history of transient, prolonged, or cyclic ruffling activity. Extended microspike structures, often preceded the formation of ruffles. Immunofluorescent labeling indicated that some of these primordial contacts were in close apposition to the ends of microtubules that penetrated into the leading edge. By fluorescence and electron microscopy short bundles of actin filaments found at the base of the leading edge were identified as presumptive, primordial contacts. It is concluded that ruffles and microspikes, either independently or in combination, initiate and mark the sites for future contact. Plaque proteins then accumulate (within 10-30 s) at the contract site and, beneath ruffles, induce localized bundling of actin filaments. We propose that all primordial contacts support traction for leading edge protrusion but that only some persist long enough to nucleate stress fiber assembly. Microtubules are postulated as the elements that select, stabilize, and potentiate the formation of these latter, long-lived contacts. PMID:3126193

THE LESSONIA NIGRESCENS SPECIES COMPLEX (LAMINARIALES, PHAEOPHYCEAE) SHOWS STRICT PARAPATRY AND COMPLETE REPRODUCTIVE ISOLATION IN A SECONDARY CONTACT ZONE(1).

PubMed

Tellier, Florence; Tapia, Javier; Faugeron, Sylvain; Destombe, Christophe; Valero, Myriam

2011-08-01

During secondary contact between phylogenetically closely related species (sibling species) having diverged in allopatry, the maintenance of species integrity depends on intrinsic and extrinsic reproductive barriers. In kelps (Phaeophyceae), the observations of hybrids in laboratory conditions suggest that reproductive isolation is incomplete. However, not all interspecific crosses are successful, and very few hybrids have been observed in nature, despite the co-occurrence of many kelp species in sympatry. This suggests that there are reproductive barriers that maintain species integrity. In this study, we characterized the fine genetic structure of a secondary contact zone to clarify the extent of reproductive isolation between two sister species. In Lessonia nigrescens Bory (Laminariales, Phaeophyta) species complex, two cryptic species have been recently found out from gene phylogenies, and-waiting for a formal taxonomic description-we used their geographic distribution to name them (northern and southern species). We studied 12 populations, distributed along 50 km of coastline, and employed two molecular approaches, assigning individuals to phylogenetic species according to a diagnostic mitochondrial marker (351 individuals analyzed) and quantifying interspecific gene flow with four microsatellite markers (248 individuals analyzed). No hybridization or introgression was revealed, indicating complete reproductive isolation in natural conditions. Unexpectedly, our study demonstrated that the two species were strictly segregated in space. This absence of co-occurrence along the contact zone can partially explain the lack of hybridization, raising new interesting questions as to the mechanisms that limit sympatry at small spatial scales. © 2011 Phycological Society of America.

Mycobacterium tuberculosis Infection in Close Childhood Contacts of Adults with Pulmonary Tuberculosis is Increased by Secondhand Exposure to Tobacco.

PubMed

Adetifa, Ifedayo M O; Kendall, Lindsay; Donkor, Simon; Lugos, Moses D; Hammond, Abdulrahman S; Owiafe, Patrick K; Ota, Martin O C; Brookes, Roger H; Hill, Philip C

2017-08-01

Tobacco use is a major risk factor for tuberculosis (TB). Secondhand smoke (SHS) is also a risk factor for TB and to a lesser extent, Mycobacterium tuberculosis infection without disease. We investigated the added risk of M. tuberculosis infection due to SHS exposure in childhood contacts of TB cases in The Gambia. Participants were childhood household contacts aged ≤ 14 years of newly diagnosed pulmonary TB (PTB) cases. The intensity of exposure to the case was categorized according to whether contacts slept in the same room, same house, or a different house as the case. Contacts were tested with an enzyme-linked immunospot interferon gamma release assay. In multivariate regression models, M. tuberculosis infection was associated with increasing exposure to a case (odds ratios [OR]: 3.9, 95% confidence interval [CI]: 2.11-71.4, P < 0.001]) and with male gender (OR: 1.5 [95% CI: 1.12-2.11], P = 0.008). Tobacco use caused a 3-fold increase in the odds of M. tuberculosis infection in children who slept closest to a case who smoked within the same home compared with a nonsmoking case (OR: 8.0 [95% CI: 2.74-23.29] versus 2.4 [95% CI: 1.17-4.92], P < 0.001). SHS exposure as an effect modifier appears to greatly increase the risk of M. tuberculosis infection in children exposed to PTB cases. Smoking cessation campaigns may be important for reducing transmission of M. tuberculosis to children within households.

76 FR 10912 - National Institute of Nursing Research; Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-28

... Nursing Research; Notice of Closed Meetings Pursuant to section 10(d) of the Federal Advisory Committee... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Nursing....) Contact Person: Tamizchelvi Thyagarajan, PhD, Scientific Review Officer, National Institute of Nursing...

78 FR 75358 - National Institute on Aging; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-11

... personal privacy. Name of Committee: National Institute on Aging Special Emphasis Panel; Vitamin D Trials...; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee Act, as amended (5 U... 20892 (Telephone Conference Call). Contact Person: Rebecca J. Ferrell, Ph.D., Scientific Review Officer...

Double closed-loop cascade control for lower limb exoskeleton with elastic actuation.

PubMed

Zhu, Yanhe; Zheng, Tianjiao; Jin, Hongzhe; Yang, Jixing; Zhao, Jie

2015-01-01

Unlike traditional rigid actuators, the significant features of Series Elastic Actuator (SEA) are stable torque control, lower output impedance, impact resistance and energy storage. Recently, SEA has been applied in many exoskeletons. In such applications, a key issue is how to realize the human-exoskeleton movement coordination. In this paper, double closed-loop cascade control for lower limb exoskeleton with SEA is proposed. This control method consists of inner SEA torque loop and outer contact force loop. Utilizing the SEA torque control with a motor velocity loop, actuation performances of SEA are analyzed. An integrated exoskeleton control system is designed, in which joint angles are calculated by internal encoders and resolvers and contact forces are gathered by external pressure sensors. The double closed-loop cascade control model is established based on the feedback signals of internal and external sensor. Movement experiments are accomplished in our prototype of lower limb exoskeleton. Preliminary results indicate the exoskeleton movements with pilot can be realized stably by utilizing this double closed-loop cascade control method. Feasibility of the SEA in our exoskeleton robot and effectiveness of the control method are verified.

Naval stores research at the Forest Products Laboratory, past and present

Treesearch

Duane F. Zinkel

1987-01-01

As many of you may not be familiar with Forest Products Laboratory, allow me to introduce it to you. The Forest Products Laboratory is a Federal government laboratory of the United States Department of Agriculture and, more specifically, of the Forest Service. The Laboratory was built in Madison, Wisconsin in close cooperation with the University of Wisconsin to serve...

Order of magnitude improvement of nano-contact spin torque nano-oscillator performance.

PubMed

Banuazizi, Seyed Amir Hossein; Sani, Sohrab R; Eklund, Anders; Naiini, Maziar M; Mohseni, Seyed Majid; Chung, Sunjae; Dürrenfeld, Philipp; Malm, B Gunnar; Åkerman, Johan

2017-02-02

Spin torque nano-oscillators (STNO) represent a unique class of nano-scale microwave signal generators and offer a combination of intriguing properties, such as nano sized footprint, ultrafast modulation rates, and highly tunable microwave frequencies from 100 MHz to close to 100 GHz. However, their low output power and relatively high threshold current still limit their applicability and must be improved. In this study, we investigate the influence of the bottom Cu electrode thickness (t Cu ) in nano-contact STNOs based on Co/Cu/NiFe GMR stacks and with nano-contact diameters ranging from 60 to 500 nm. Increasing t Cu from 10 to 70 nm results in a 40% reduction of the threshold current, an order of magnitude higher microwave output power, and close to two orders of magnitude better power conversion efficiency. Numerical simulations of the current distribution suggest that these dramatic improvements originate from a strongly reduced lateral current spread in the magneto-dynamically active region.

Labral reconstruction with iliotibial band autografts and semitendinosus allografts improves hip joint contact area and contact pressure: an in vitro analysis.

PubMed

Lee, Simon; Wuerz, Thomas H; Shewman, Elizabeth; McCormick, Frank M; Salata, Michael J; Philippon, Marc J; Nho, Shane J

2015-01-01

Labral reconstruction using iliotibial band (ITB) autografts and semitendinosus (Semi-T) allografts has recently been described in cases of labral deficiency. To characterize the joint biomechanics with a labrum-intact, labrum-deficient, and labrum-reconstructed acetabulum in a hip cadaveric model. The hypothesis was that labral resection would decrease contact area, increase contact pressure, and increase peak force, while subsequent labral reconstruction with ITB autografts or Semi-T allografts would restore these values toward the native intact labral state. Controlled laboratory study. Ten fresh-frozen human cadaveric hips were analyzed utilizing thin-film piezoresistive load sensors to measure contact area, contact pressure, and peak force (1) with the native intact labrum, (2) after segmental labral resection, and (3) after graft labral reconstruction with either ITB autografts or Semi-T allografts. Each specimen was examined at 20° of extension and 60° of flexion. Statistical analysis was conducted through 1-way analysis of variance with post hoc Games-Howell tests. For the ITB group, labral resection significantly decreased contact area (at 20°: 73.2%±5.38%, P=.0010; at 60°: 78.5%±6.93%, P=.0063) and increased contact pressure (at 20°: 106.7%±4.15%, P=.0387; at 60°: 103.9%±1.15%, P=.0428). In addition, ITB reconstruction improved contact area (at 20°: 87.2%±12.3%, P=.0130; at 60°: 90.5%±8.81%, P=.0079) and contact pressure (at 20°: 98.5%±5.71%, P=.0476; at 60°: 96.6%±1.13%, P=.0056) from the resected state. Contact pressure at 60° of flexion was significantly lower compared with the native labrum (P=.0420). For the Semi-T group, labral resection significantly decreased contact area (at 20°: 68.1%±12.57%, P=.0002; at 60°: 67.5%±6.70%, P=.0002) and increased contact pressure (at 20°: 105.3%±3.73%, P=.0304; at 60°: 106.8%±4.04%, P=.0231). Semi-T reconstruction improved contact area (at 20°: 87.9%±7.95%, P=.0087; at 60°: 92.9%±13

The flight robotics laboratory

NASA Technical Reports Server (NTRS)

Tobbe, Patrick A.; Williamson, Marlin J.; Glaese, John R.

1988-01-01

The Flight Robotics Laboratory of the Marshall Space Flight Center is described in detail. This facility, containing an eight degree of freedom manipulator, precision air bearing floor, teleoperated motion base, reconfigurable operator's console, and VAX 11/750 computer system, provides simulation capability to study human/system interactions of remote systems. The facility hardware, software and subsequent integration of these components into a real time man-in-the-loop simulation for the evaluation of spacecraft contact proximity and dynamics are described.

Reducing contact resistance in graphene devices through contact area patterning.

PubMed

Smith, Joshua T; Franklin, Aaron D; Farmer, Damon B; Dimitrakopoulos, Christos D

2013-04-23

Performance of graphene electronics is limited by contact resistance associated with the metal-graphene (M-G) interface, where unique transport challenges arise as carriers are injected from a 3D metal into a 2D-graphene sheet. In this work, enhanced carrier injection is experimentally achieved in graphene devices by forming cuts in the graphene within the contact regions. These cuts are oriented normal to the channel and facilitate bonding between the contact metal and carbon atoms at the graphene cut edges, reproducibly maximizing "edge-contacted" injection. Despite the reduction in M-G contact area caused by these cuts, we find that a 32% reduction in contact resistance results in Cu-contacted, two-terminal devices, while a 22% reduction is achieved for top-gated graphene transistors with Pd contacts as compared to conventionally fabricated devices. The crucial role of contact annealing to facilitate this improvement is also elucidated. This simple approach provides a reliable and reproducible means of lowering contact resistance in graphene devices to bolster performance. Importantly, this enhancement requires no additional processing steps.

Limitation of Optical Enhancement in Ultra-thin Solar Cells Imposed by Contact Selectivity.

PubMed

Islam, Raisul; Saraswat, Krishna

2018-06-11

Ultra-thin crystalline silicon (c-Si) solar cell suffers both from poor light absorption and minority carrier recombination at the contacts resulting in low contact selectivity. Yet most of the research focuses on improving the light absorption by introducing novel light trapping technique. Our work shows that for ultra-thin absorber, the benefit of optical enhancement is limited by low contact selectivity. Using simulation we observe that performance enhancement from light trapping starts to saturate as the absorber scales down because of the increase in probability of the photo-generated carriers to recombine at the metal contact. Therefore, improving the carrier selectivity of the contacts, which reduces the recombination at contacts, is important to improve the performance of the solar cell beyond what is possible by enhancing light absorption only. The impact of improving contact selectivity increases as the absorber thickness scales below 20 micrometer (μm). Light trapping provides better light management and improving contact selectivity provides better photo-generated carrier management. When better light management increases the number of photo-generated carriers, better carrier management is a useful optimization knob to achieve the efficiency close to the thermodynamic limit. Our work explores a design trade-off in detail which is often overlooked by the research community.

21. Photographic contact print from a 8x10 original negative. (Original ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

21. Photographic contact print from a 8x10 original negative. (Original drawing located on abandoned NASA site, currently owned by the City of Downey, Downey, California). 1954 NORTH AMERICAN AVIATION BUILDING 41 CONSTRUCTION LAYOUT. - NASA Industrial Plant, Missile Research Laboratory, 12214 Lakewood Boulevard, Downey, Los Angeles County, CA

Co-Occurring Atomic Contacts for the Characterization of Protein Binding Hot Spots.

PubMed

Liu, Qian; Ren, Jing; Song, Jiangning; Li, Jinyan

2015-01-01

A binding hot spot is a small area at a protein-protein interface that can make significant contribution to binding free energy. This work investigates the substantial contribution made by some special co-occurring atomic contacts at a binding hot spot. A co-occurring atomic contact is a pair of atomic contacts that are close to each other with no more than three covalent-bond steps. We found that two kinds of co-occurring atomic contacts can play an important part in the accurate prediction of binding hot spot residues. One is the co-occurrence of two nearby hydrogen bonds. For example, mutations of any residue in a hydrogen bond network consisting of multiple co-occurring hydrogen bonds could disrupt the interaction considerably. The other kind of co-occurring atomic contact is the co-occurrence of a hydrophobic carbon contact and a contact between a hydrophobic carbon atom and a π ring. In fact, this co-occurrence signifies the collective effect of hydrophobic contacts. We also found that the B-factor measurements of several specific groups of amino acids are useful for the prediction of hot spots. Taking the B-factor, individual atomic contacts and the co-occurring contacts as features, we developed a new prediction method and thoroughly assessed its performance via cross-validation and independent dataset test. The results show that our method achieves higher prediction performance than well-known methods such as Robetta, FoldX and Hotpoint. We conclude that these contact descriptors, in particular the novel co-occurring atomic contacts, can be used to facilitate accurate and interpretable characterization of protein binding hot spots.

Co-Occurring Atomic Contacts for the Characterization of Protein Binding Hot Spots

PubMed Central

Liu, Qian; Ren, Jing; Song, Jiangning; Li, Jinyan

2015-01-01

A binding hot spot is a small area at a protein-protein interface that can make significant contribution to binding free energy. This work investigates the substantial contribution made by some special co-occurring atomic contacts at a binding hot spot. A co-occurring atomic contact is a pair of atomic contacts that are close to each other with no more than three covalent-bond steps. We found that two kinds of co-occurring atomic contacts can play an important part in the accurate prediction of binding hot spot residues. One is the co-occurrence of two nearby hydrogen bonds. For example, mutations of any residue in a hydrogen bond network consisting of multiple co-occurring hydrogen bonds could disrupt the interaction considerably. The other kind of co-occurring atomic contact is the co-occurrence of a hydrophobic carbon contact and a contact between a hydrophobic carbon atom and a π ring. In fact, this co-occurrence signifies the collective effect of hydrophobic contacts. We also found that the B-factor measurements of several specific groups of amino acids are useful for the prediction of hot spots. Taking the B-factor, individual atomic contacts and the co-occurring contacts as features, we developed a new prediction method and thoroughly assessed its performance via cross-validation and independent dataset test. The results show that our method achieves higher prediction performance than well-known methods such as Robetta, FoldX and Hotpoint. We conclude that these contact descriptors, in particular the novel co-occurring atomic contacts, can be used to facilitate accurate and interpretable characterization of protein binding hot spots. PMID:26675422

Plasma creatinine in dogs: intra- and inter-laboratory variation in 10 European veterinary laboratories

PubMed Central

2011-01-01

Background There is substantial variation in reported reference intervals for canine plasma creatinine among veterinary laboratories, thereby influencing the clinical assessment of analytical results. The aims of the study was to determine the inter- and intra-laboratory variation in plasma creatinine among 10 veterinary laboratories, and to compare results from each laboratory with the upper limit of its reference interval. Methods Samples were collected from 10 healthy dogs, 10 dogs with expected intermediate plasma creatinine concentrations, and 10 dogs with azotemia. Overlap was observed for the first two groups. The 30 samples were divided into 3 batches and shipped in random order by postal delivery for plasma creatinine determination. Statistical testing was performed in accordance with ISO standard methodology. Results Inter- and intra-laboratory variation was clinically acceptable as plasma creatinine values for most samples were usually of the same magnitude. A few extreme outliers caused three laboratories to fail statistical testing for consistency. Laboratory sample means above or below the overall sample mean, did not unequivocally reflect high or low reference intervals in that laboratory. Conclusions In spite of close analytical results, further standardization among laboratories is warranted. The discrepant reference intervals seem to largely reflect different populations used in establishing the reference intervals, rather than analytical variation due to different laboratory methods. PMID:21477356

Prioritized Contact Transport Stream

NASA Technical Reports Server (NTRS)

Hunt, Walter Lee, Jr. (Inventor)

2015-01-01

A detection process, contact recognition process, classification process, and identification process are applied to raw sensor data to produce an identified contact record set containing one or more identified contact records. A prioritization process is applied to the identified contact record set to assign a contact priority to each contact record in the identified contact record set. Data are removed from the contact records in the identified contact record set based on the contact priorities assigned to those contact records. A first contact stream is produced from the resulting contact records. The first contact stream is streamed in a contact transport stream. The contact transport stream may include and stream additional contact streams. The contact transport stream may be varied dynamically over time based on parameters such as available bandwidth, contact priority, presence/absence of contacts, system state, and configuration parameters.

Investigation into the mechanisms of closed three-body abrasive wear

NASA Astrophysics Data System (ADS)

Dwyer-Joyce, R. S.; Sayles, R. S.; Ioannides, E.

1994-06-01

Contacting components frequently fail by abrasion caused by solid contaminants in the lubricant. This process can be classified as a closed three-body abrasive wear process. The mechanisms by which trapped particles cause material removal are not fully understood. This paper describes tests using model elastohydrodynamic contacts to study these mechanisms. An optical elastohydrodynamic lubrication rig has been used to study the deformation and fracture of ductile and brittle lubricant-borne debris. A ball-on-disk machine was used to study the behavior of the particles in partially sliding contacts. Small diamond particles were used as abrasives since these were thought not to break down in the contact; wear could then be directly related to particles of a known size. The particles were found to embed in the softer surface and to scratch the harder. The mass of material worn from the ball surface was approximately proportional to the particle sliding distance and abrasive concentration. Small particles tumbled through the contact, while larger particles ploughed. Mass loss was found to increase with abrasive particle size. Individual abrasion scratches have been measured and related to the abrading particle. A simple model of the abrasive process has been developed and compared with experimental data. The discrepancies are thought to be the result of the uncertainty about the entrainment of particles into the contact.

Cysticercosis in laboratory rabbits.

PubMed

Owiny, J R

2001-03-01

There are no data on the current incidence of Taenia pisiformis in laboratory rabbits. Two cases of cysticercosis most likely due to T. pisiformis in laboratory rabbits (intermediate host) are presented. Both rabbits had no contact with dogs (final host); their caretakers did not work with dogs, and these caretakers changed into facility scrubs and wore gloves when working with the rabbits. Rabbit 1 may have been infected after being fed hay at our facility. In light of the life cycle of the parasite and the history of rabbit 2, it potentially could have been infected prior to arrival at our facility. There have been only three cases of tapeworm cysts in rabbits in our facility (average daily census, 250) during the last 10 years (incidence, < 1%). This report indicates that although cysticercosis is rare in laboratory rabbits, one should always be aware of such incidental findings. Although it may not produce overt illness in the rabbit, hepatic migration could adversely affect the outcome of some experimental procedures

77 FR 32652 - National Institute of Nursing Research; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... Nursing Research; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee Act... unwarranted invasion of personal privacy. Name of Committee: National Institute of Nursing Research Initial... 20814. Contact Person: Weiqun Li, M.D., Scientific Review Officer, National Institute of Nursing...

77 FR 59941 - National Institute of Nursing Research; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-01

... Nursing Research; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee Act... unwarranted invasion of personal privacy. Name of Committee: National Institute of Nursing Research Initial... 20814. Contact Person: Weiqun Li, MD, Scientific Review Officer, National Institute of Nursing Research...

American Contact Dermatitis Society Contact Allergy Management Program: An Epidemiologic Tool to Determine Relative Prevalence of Contact Allergens.

PubMed

Scheman, Andrew; Severson, David

2016-01-01

Data on the prevalence of contact allergy in North America are currently reported by groups of academic contact allergy specialists at select academic centers. Sampling of data from numerous centers across North America, including practices performing more limited patch testing, would provide a broader perspective of contact allergen prevalence in North America. The American Contact Dermatitis Society Contact Allergy Management Program is an ideal tool for collection of epidemiologic data regarding contact allergy prevalence in North America. The aim of the study was to identify the relative prevalence of contact allergy to common contact allergens in North America. Mapping of Contact Allergy Management Program (CAMP) data was performed to allow analysis of how frequently searches were performed for various contact allergens. The number of searches performed for specific allergens provides a measure of the relative prevalence of contact allergy to these allergens. The top 35 allergens for the period from November 18, 2012 to November 18, 2013 are reported. Although these data are useful, specific recommendations for minor alterations to CAMP are discussed, which will allow future CAMP data to be stratified and more powerful. With minor modifications, CAMP can provide a quantum leap in the reporting of contact allergy epidemiologic data in North America.

77 FR 23499 - Notice of Intent To Repatriate Cultural Items: Museum of Indian Arts & Culture/Laboratory of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-19

... Cultural Items: Museum of Indian Arts & Culture/Laboratory of Anthropology, Museum of New Mexico, Santa Fe... & Culture/Laboratory of Anthropology, Museum of New Mexico, in consultation with the appropriate Indian... contact the Museum of Indian Arts & Culture/Laboratory of Anthropology, Museum of New Mexico. DATES...

Contact position sensor using constant contact force control system

NASA Technical Reports Server (NTRS)

Sturdevant, Jay (Inventor)

1995-01-01

A force control system (50) and method are provided for controlling a position contact sensor (10) so as to produce a constant controlled contact force therewith. The system (50) includes a contact position sensor (10) which has a contact probe (12) for contacting the surface of a target to be measured and an output signal (V.sub.o) for providing a position indication thereof. An actuator (30) is provided for controllably driving the contact position sensor (10) in response to an actuation control signal (I). A controller (52) receives the position indication signal (V.sub.o) and generates in response thereto the actuation control signal (I) so as to provide a substantially constant selective force (F) exerted by the contact probe (12). The actuation drive signal (I) is generated further in response to substantially linear approximation curves based on predetermined force and position data attained from the sensor (10) and the actuator (30).

Contact resistance evolution of highly cycled, lightly loaded micro-contacts

NASA Astrophysics Data System (ADS)

Stilson, Christopher; Coutu, Ronald

2014-03-01

Reliable microelectromechanical systems (MEMS) switches are critical for developing high performance radio frequency circuits like phase shifters. Engineers have attempted to improve reliability and lifecycle performance using novel contact metals, unique mechanical designs and packaging. Various test fixtures including: MEMS devices, atomic force microscopes (AFM) and nanoindentors have been used to collect resistance and contact force data. AFM and nanoindentor test fixtures allow direct contact force measurements but are severely limited by low resonance sensors, and therefore low data collection rates. This paper reports the contact resistance evolution results and fabrication of thin film, sputtered and evaporated gold, micro-contacts dynamically tested up to 3kHz. The upper contact support structure consists of a gold surface micromachined, fix-fix beam designed with sufficient restoring force to overcome adhesion. The hemisphere-upper and planar-lower contacts are mated with a calibrated, external load resulting in approximately 100μN of contact force and are cycled in excess of 106 times or until failure. Contact resistance is measured, in-situ, using a cross-bar configuration and the entire apparatus is isolated from external vibration and housed in an enclosure to minimize contamination due to ambient environment. Additionally, contact cycling and data collection are automated using a computer and LabVIEW. Results include contact resistance measurements of 6 and 8 μm radius contact bumps and lifetime testing up to 323.6 million cycles.

Contact solution algorithms

NASA Technical Reports Server (NTRS)

Tielking, John T.

1989-01-01

Two algorithms for obtaining static contact solutions are described in this presentation. Although they were derived for contact problems involving specific structures (a tire and a solid rubber cylinder), they are sufficiently general to be applied to other shell-of-revolution and solid-body contact problems. The shell-of-revolution contact algorithm is a method of obtaining a point load influence coefficient matrix for the portion of shell surface that is expected to carry a contact load. If the shell is sufficiently linear with respect to contact loading, a single influence coefficient matrix can be used to obtain a good approximation of the contact pressure distribution. Otherwise, the matrix will be updated to reflect nonlinear load-deflection behavior. The solid-body contact algorithm utilizes a Lagrange multiplier to include the contact constraint in a potential energy functional. The solution is found by applying the principle of minimum potential energy. The Lagrange multiplier is identified as the contact load resultant for a specific deflection. At present, only frictionless contact solutions have been obtained with these algorithms. A sliding tread element has been developed to calculate friction shear force in the contact region of the rolling shell-of-revolution tire model.

Enhanced external and culturally sensitive attributions after extended intercultural contact.

PubMed

Vollhardt, Johanna Ray

2010-06-01

This study examined the effect of close and extended intercultural contact on attributions for behaviour of out-group members. Specifically, it was hypothesized that extended intercultural contact would enhance the ability to make external and culturally sensitive attributions for ambiguous behaviour of out-group members, while decreasing the common tendency to overestimate internal factors. A content analysis of open-ended attributions supported these hypotheses, revealing that majority group members in Germany who had hosted an exchange student from another continent used significantly less internal and more external as well as culturally sensitive attributions to explain the behaviour described in critical intercultural incidents, compared to future hosts. The effect remained significant when controlling for perspective taking and prior intercultural experience. Moreover, the hypothesis was supported for scenarios describing different cultural groups (regardless of the exchange students' country of origin), suggesting a generalized effect. Problems of selection bias are discussed, and the importance of studying a range of positive outcomes of intercultural contact is emphasized.

Closed-Loop HIRF Experiments Performed on a Fault Tolerant Flight Control Computer

NASA Technical Reports Server (NTRS)

Belcastro, Celeste M.

1997-01-01

ABSTRACT Closed-loop HIRF experiments were performed on a fault tolerant flight control computer (FCC) at the NASA Langley Research Center. The FCC used in the experiments was a quad-redundant flight control computer executing B737 Autoland control laws. The FCC was placed in one of the mode-stirred reverberation chambers in the HIRF Laboratory and interfaced to a computer simulation of the B737 flight dynamics, engines, sensors, actuators, and atmosphere in the Closed-Loop Systems Laboratory. Disturbances to the aircraft associated with wind gusts and turbulence were simulated during tests. Electrical isolation between the FCC under test and the simulation computer was achieved via a fiber optic interface for the analog and discrete signals. Closed-loop operation of the FCC enabled flight dynamics and atmospheric disturbances affecting the aircraft to be represented during tests. Upset was induced in the FCC as a result of exposure to HIRF, and the effect of upset on the simulated flight of the aircraft was observed and recorded. This paper presents a description of these closed- loop HIRF experiments, upset data obtained from the FCC during these experiments, and closed-loop effects on the simulated flight of the aircraft.

Cost-Effectiveness of a Chemoprophylactic Intervention with Single Dose Rifampicin in Contacts of New Leprosy Patients

PubMed Central

Idema, Willemijn J.; Majer, Istvan M.; Pahan, David; Oskam, Linda; Polinder, Suzanne; Richardus, Jan Hendrik

2010-01-01

Background With 249,007 new leprosy patients detected globally in 2008, it remains necessary to develop new and effective interventions to interrupt the transmission of M. leprae. We assessed the economic benefits of single dose rifampicin (SDR) for contacts as chemoprophylactic intervention in the control of leprosy. Methods We conducted a single centre, double blind, cluster randomised, placebo controlled trial in northwest Bangladesh between 2002 and 2007, including 21,711 close contacts of 1,037 patients with newly diagnosed leprosy. We gave a single dose of rifampicin or placebo to close contacts, with follow-up for four years. The main outcome measure was the development of clinical leprosy. We assessed the cost effectiveness by calculating the incremental cost effectiveness ratio (ICER) between the standard multidrug therapy (MDT) program with the additional chemoprophylaxis intervention versus the standard MDT program only. The ICER was expressed in US dollars per prevented leprosy case. Findings Chemoprophylaxis with SDR for preventing leprosy among contacts of leprosy patients is cost-effective at all contact levels and thereby a cost-effective prevention strategy. In total, $6,009 incremental cost was invested and 38 incremental leprosy cases were prevented, resulting in an ICER of $158 per one additional prevented leprosy case. It was the most cost-effective in neighbours of neighbours and social contacts (ICER $214), slightly less cost-effective in next door neighbours (ICER $497) and least cost-effective among household contacts (ICER $856). Conclusion Chemoprophylaxis with single dose rifampicin given to contacts of newly diagnosed leprosy patients is a cost-effective intervention strategy. Implementation studies are necessary to establish whether this intervention is acceptable and feasible in other leprosy endemic areas of the world. PMID:21072235

Beta Atomic Contacts: Identifying Critical Specific Contacts in Protein Binding Interfaces

PubMed Central

Liu, Qian; Kwoh, Chee Keong; Hoi, Steven C. H.

2013-01-01

Specific binding between proteins plays a crucial role in molecular functions and biological processes. Protein binding interfaces and their atomic contacts are typically defined by simple criteria, such as distance-based definitions that only use some threshold of spatial distance in previous studies. These definitions neglect the nearby atomic organization of contact atoms, and thus detect predominant contacts which are interrupted by other atoms. It is questionable whether such kinds of interrupted contacts are as important as other contacts in protein binding. To tackle this challenge, we propose a new definition called beta (β) atomic contacts. Our definition, founded on the β-skeletons in computational geometry, requires that there is no other atom in the contact spheres defined by two contact atoms; this sphere is similar to the van der Waals spheres of atoms. The statistical analysis on a large dataset shows that β contacts are only a small fraction of conventional distance-based contacts. To empirically quantify the importance of β contacts, we design βACV, an SVM classifier with β contacts as input, to classify homodimers from crystal packing. We found that our βACV is able to achieve the state-of-the-art classification performance superior to SVM classifiers with distance-based contacts as input. Our βACV also outperforms several existing methods when being evaluated on several datasets in previous works. The promising empirical performance suggests that β contacts can truly identify critical specific contacts in protein binding interfaces. β contacts thus provide a new model for more precise description of atomic organization in protein quaternary structures than distance-based contacts. PMID:23630569

Superconducting Sweet-Spot in Microcrystalline Graphite Revealed by Point-Contact Spectroscopy

NASA Astrophysics Data System (ADS)

Arnold, F.; Nyéki, J.; Saunders, J.

2018-05-01

In this letter we describe the observation of a magnetic field dependent electronic gap, suggestive of local superconductivity, in the point-contact spectrum of micro-crystalline graphite. Magnetic field dependent point-contact spectroscopy was carried out at a temperature of 1.8K using an etched aluminium tip. At zero field a gap structure in the differential conductance is observed, showing a gap of Δ = 4.2 meV. On applying magnetic fields of up to 500mT, this gap gradually closes, following the theoretical prediction by Ginzburg and Landau for a fully flux-penetrated superconductor. By applying BCS-theory, we infer a critical superconducting temperature of 14K.

Acceptability of chemoprophylaxis for household contacts of leprosy patients in Bangladesh: a qualitative study.

PubMed

Feenstra, Sabiena G; Nahar, Quamrun; Pahan, David; Oskam, Linda; Richardus, Jan Hendrik

2011-06-01

Chemoprophylaxis with single dose rifampicin is a promising intervention to prevent leprosy in close contacts of patients. However, application in control programmes often requires disclosure of the leprosy diagnosis, which is still a stigmatised disease in many countries. Promoting control and treatment of stigmatised diseases without contributing towards stigma of the individuals involved can be very difficult. The objective of this study was to assess the social acceptability of disclosure of the diagnosis and the attitude towards taking prophylactic medicines in a leprosy endemic area in Bangladesh. Qualitative study through focus group discussions with 136 healthy men and women from different age groups and religions, coming from two rural villages and an urban area in northwest Bangladesh, and 14 health workers with extensive experience with leprosy patients. The participants would not object to disclosure of the diagnosis to household members and nearby family if they were diagnosed with leprosy. However, many participants were not willing to share this information with their neighbours and other social contacts due to stigma of the disease. All healthy participants were willing to take chemoprophylaxis if any of their close contacts were diagnosed with leprosy, even after explaining that full protection against leprosy was not guaranteed. It can be concluded that chemoprophylaxis for household contacts of leprosy patients is an effective and socially acceptable addition to the current leprosy control programme. Chemoprophylaxis for other categories of contacts likely to benefit would only be feasible, without disclosure of patient information, if given in the form of mass campaigns for the whole population in the area.

Contact Lens Solutions and Contact Lens Discomfort: Examining the Correlations Between Solution Components, Keratitis, and Contact Lens Discomfort.

PubMed

Kuc, Christopher J; Lebow, Kenneth A

2018-06-13

This article will examine the current literature, as it relates to contact lens discomfort (CLD) secondary to contact lens solutions. The reader will better understand the characteristics of contact lenses, as they uniquely interact with each type of contact lens solution and also gain a better comprehension of the components of contact lens solution such as preservatives, surfactants, and chelating agents, which may contribute to discomfort. By investigating corneal staining theory and the mechanisms that contribute to its presence, the reader will gain insight into this clinical finding, which relates to selection of contact lens solutions. The FDA standards for testing solutions and how this relates to contact lens keratitis will also be appraised in regards to current ISO recommendations. Finally, better selection of multipurpose contact lens solution (MPS) and hydrogen peroxide-based solutions for patients should be accessible to the clinician based on this review and preexisting clinical findings or diagnoses. A review of current published literature from peer reviewed journals and online journals was conducted to gain an understanding of contact lens solution's impact on contact lens discomfort. Many studies have been conducted comparing comfort between various types of contact lens solutions. It is challenging to decipher this information and apply it clinically when selecting solutions for patients. By comparing solution components, how contact lens solutions interact with different types of lenses, keratitis related to contact lenses, and preexisting ocular conditions, this review will improve a clinician's ability to eliminate CLD.

Integrated geostatistics for modeling fluid contacts and shales in Prudhoe Bay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perez, G.; Chopra, A.K.; Severson, C.D.

1997-12-01

Geostatistics techniques are being used increasingly to model reservoir heterogeneity at a wide range of scales. A variety of techniques is now available with differing underlying assumptions, complexity, and applications. This paper introduces a novel method of geostatistics to model dynamic gas-oil contacts and shales in the Prudhoe Bay reservoir. The method integrates reservoir description and surveillance data within the same geostatistical framework. Surveillance logs and shale data are transformed to indicator variables. These variables are used to evaluate vertical and horizontal spatial correlation and cross-correlation of gas and shale at different times and to develop variogram models. Conditional simulationmore » techniques are used to generate multiple three-dimensional (3D) descriptions of gas and shales that provide a measure of uncertainty. These techniques capture the complex 3D distribution of gas-oil contacts through time. The authors compare results of the geostatistical method with conventional techniques as well as with infill wells drilled after the study. Predicted gas-oil contacts and shale distributions are in close agreement with gas-oil contacts observed at infill wells.« less

Nanobubbles in confined solution: Generation, contact angle, and stability.

PubMed

Wei, Jiachen; Zhang, Xianren; Song, Fan; Shao, Yingfeng

2018-02-14

The formation of gas bubbles presents a frequent challenge to microfluidic operations, for which fluids are geometrically confined to a microscale space. Here, to understand the mechanism of nucleating gas bubbles in microfluidic devices, we investigate the formation and stability of nanobubbles in confined solutions. Our molecular dynamics simulations show that while pinning of the contact line is a prerequisite for the stability of surface nanobubbles in open systems that can exchange gas with surrounding environment, in confined solutions, stable nanobubbles can exist even without pinning. In supersaturated condition, stable bubbles can be found in confined solutions with acute or obtuse contact angle, depending on the substrate hydrophobicity. We also demonstrate that when open to the bulk solution, the stable nanobubbles in closed systems would become unstable unless both supersaturation and pinning of the contact line are satisfied. Our results not only shed light on the design of novel heterogeneous surfaces for generating nanobubbles in confined space with controllable shape and stability but also address the crucial effect of gas exchange with the surroundings in determining the stability of nanobubbles.

Nanobubbles in confined solution: Generation, contact angle, and stability

NASA Astrophysics Data System (ADS)

Wei, Jiachen; Zhang, Xianren; Song, Fan; Shao, Yingfeng

2018-02-01

The formation of gas bubbles presents a frequent challenge to microfluidic operations, for which fluids are geometrically confined to a microscale space. Here, to understand the mechanism of nucleating gas bubbles in microfluidic devices, we investigate the formation and stability of nanobubbles in confined solutions. Our molecular dynamics simulations show that while pinning of the contact line is a prerequisite for the stability of surface nanobubbles in open systems that can exchange gas with surrounding environment, in confined solutions, stable nanobubbles can exist even without pinning. In supersaturated condition, stable bubbles can be found in confined solutions with acute or obtuse contact angle, depending on the substrate hydrophobicity. We also demonstrate that when open to the bulk solution, the stable nanobubbles in closed systems would become unstable unless both supersaturation and pinning of the contact line are satisfied. Our results not only shed light on the design of novel heterogeneous surfaces for generating nanobubbles in confined space with controllable shape and stability but also address the crucial effect of gas exchange with the surroundings in determining the stability of nanobubbles.

Language Contact.

ERIC Educational Resources Information Center

Nelde, Peter Hans

1995-01-01

Examines the phenomenon of language contact and recent trends in linguistic contact research, which focuses on language use, language users, and language spheres. Also discusses the role of linguistic and cultural conflicts in language contact situations. (13 references) (MDM)

Allergic contact dermatitis from a paper mill slimicide containing 2-bromo-4'-hydroxyacetophenone.

PubMed

Jensen, Charlotte D; Andersen, Klaus E

2003-03-01

Slimicides are biocidal products used in paper mills to inhibit the proliferation of slime-forming microorganisms that would otherwise spoil the paper products. A laboratory technician working at a paper mill had recurring dermatitis related to contact with the slimicide Busan 1130. We report the first case of allergic contact dermatitis from the slimicide Busan 1130. Diagnostic patch testing was performed with solutions of Busan 1130 and its active ingredient, 2-bromo-4'-hydroxyacetophenone (BHAP). Twenty-five controls were also tested. The patient showed a ++ reaction to 0.1% Busan 1130 aqueous solution and 0.01% BHAP in ethanol. All controls were negative. The patient had recurrent allergic contact dermatitis from exposure to BHAP contained in the slimicide Busan 1130.

Investigation of porous silicon obtained under different conditions by the contact angle method

NASA Astrophysics Data System (ADS)

Belorus, A. O.; Bukina, Y. V.; Pastukhov, A. I.; Stebko, D. S.; Spivak, Yu M.; Moshnikov, V. A.

2017-11-01

This paper investigates a hydrophobicity/hydrophilicity of porous silicon by the contact angle method. Porous silicon series were obtained by electrochemical anodic etching of n-Si (100) and (111) under the current anodization density range of 5-120 mA/cm2. For this purpose the original laboratory installation and the software «Measurement of contact angle» were developed. It is shown that, the contact angle can vary significantly (up to 80 degrees for (100)) depending on the current anodization Discussion of the results is carried out taking in account the composition of the functional groups and of surface morphology of the porous silicon. These results are important for developing porous silicon particles as nanocontainers in the targeted drug delivery.

77 FR 30019 - National Institute of Environmental Health Sciences; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-21

... Environmental Health Sciences; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... Health Sciences Special Emphasis Panel; Virtual Consortium for Translational/Transdisciplinary.... Contact Person: Janice B Allen, Ph.D., Scientific Review Administrator, Scientific Review Branch, Division...

Contact of dual mobility implants: effects of cup wear and inclination.

PubMed

Uddin, M S

2015-01-01

Cup wear and inclination on the pelvic bone are significant factors, which change the contact of the articulating surfaces, thus, impacting the long-term performance of hip implants. This paper presents a finite element (FE) analysis of the contact of the dual mobility implants under the influence of cup wear and inclination. A 3D FE model of the implant was developed with the application of equivalent physiological loading and boundary conditions. Effects of cup inclination angle ranging from 45° to 60° and the wear depth ranging from 0 to 2.46 mm equivalent to up to 30 years of the implant's life on the contact pressure and von Mises stress were investigated. Simulation results show that the contact pressure and von Mises stress decrease significantly with a modest wear depth and remains quite in-sensitive to the cup inclination angle and wear depth up to 1.64 mm. With wear depth further up to 2.46 mm, the cup thickness (i.e. cup thinning on worn region) may be more predominant than increasing of contact area between the cup and the head. The wear on the inner surface of the cup is found to rule out the overall contact pressure and stress in the implant. Furthermore, individual and combined effects of both important parameters are analysed and discussed with respect to available clinical/laboratory studies.

Measles-mumps-rubella vaccination and respiratory syncytial virus-associated hospital contact.

PubMed

Sørup, Signe; Benn, Christine Stabell; Stensballe, Lone Graff; Aaby, Peter; Ravn, Henrik

2015-01-01

The live measles vaccine has been associated with lower non-measles mortality and admissions in low-income countries. The live measles-mumps-rubella vaccine has also been associated with lower rate of admissions with any type of infection in Danish children; the association was strongest for admissions with lower respiratory infections. To examine whether measles, mumps, and rubella (MMR) vaccination was associated with reduced rate of hospital contact related to respiratory syncytial virus (RSV) in a high-income country. Nationwide cohort study of laboratory-confirmed RSV hospital contacts at age 14-23 months in all children born in Denmark 1997-2002 who had already received the vaccine against diphtheria, tetanus, pertussis (acellular), polio, and Haemophilus influenzae type b (DTaP-IPV-Hib) at the recommended ages of 3, 5, and 12 months. The study included 888 RSV hospital contacts in 128,588 person years of follow up (rate 6.8/1000 person years). Having MMR as the most recent vaccine was associated with a reduced rate of RSV hospital contacts compared with having DTaP-IPV-Hib as the most recent vaccine (Incidence rate ratio (IRR), 0.75; 95% confidence interval (CI), 0.63-0.89). After adjustment for potential confounders including exact age in days the IRR was 0.78 (95% CI, 0.66-0.93). The adjusted IRR was 0.74 (95% CI, 0.60-0.92) in males and 0.84 (95% CI, 0.66-1.06) in females (P Interaction, 0.42). There was no association in the first month after MMR vaccination (adjusted IRR, 0.97; 95% CI, 0.76-1.24) but the adjusted IRR was 0.70 (95% CI, 0.58-0.85) from one month after MMR vaccination. MMR vaccination was associated with reduced rate of hospital contacts related to laboratory-confirmed RSV infection. Further research on the association between MMR vaccination and other unrelated pathogens are warranted. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

76 FR 60508 - National Institute of Nursing Research; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-29

... Nursing Research; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee Act... unwarranted invasion of personal privacy. Name of Committee: National Institute of Nursing Research Initial..., Bethesda, MD 20817. Contact Person: Weiqun Li, MD, Scientific Review Officer, National Institute of Nursing...

78 FR 63996 - National Institute of Nursing Research; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-25

... Nursing Research; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee Act... unwarranted invasion of personal privacy. Name of Committee: National Institute of Nursing Research Initial..., Bethesda, MD 20814. Contact Person: Weiqun Li, MD, Scientific Review Officer, National Institute of Nursing...

75 FR 8373 - National Human Genome Research Institute; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

... Research Institute; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory Committee... unwarranted invasion of personal privacy. Name of Committee: National Human Genome Research Institute Special..., NHGRI Twinbrook Library, 5635 Fishers Lane, Bethesda, MD 20892-9306. Contact Person: Keith McKenney, PhD...

Simple processing of back-contacted silicon heterojunction solar cells using selective-area crystalline growth

NASA Astrophysics Data System (ADS)

Tomasi, Andrea; Paviet-Salomon, Bertrand; Jeangros, Quentin; Haschke, Jan; Christmann, Gabriel; Barraud, Loris; Descoeudres, Antoine; Seif, Johannes Peter; Nicolay, Sylvain; Despeisse, Matthieu; de Wolf, Stefaan; Ballif, Christophe

2017-04-01

For crystalline-silicon solar cells, voltages close to the theoretical limit are nowadays readily achievable when using passivating contacts. Conversely, maximal current generation requires the integration of the electron and hole contacts at the back of the solar cell to liberate its front from any shadowing loss. Recently, the world-record efficiency for crystalline-silicon single-junction solar cells was achieved by merging these two approaches in a single device; however, the complexity of fabricating this class of devices raises concerns about their commercial potential. Here we show a contacting method that substantially simplifies the architecture and fabrication of back-contacted silicon solar cells. We exploit the surface-dependent growth of silicon thin films, deposited by plasma processes, to eliminate the patterning of one of the doped carrier-collecting layers. Then, using only one alignment step for electrode definition, we fabricate a proof-of-concept 9-cm2 tunnel-interdigitated back-contact solar cell with a certified conversion efficiency >22.5%.

Drop rebound after impact: the role of the receding contact angle.

PubMed

Antonini, C; Villa, F; Bernagozzi, I; Amirfazli, A; Marengo, M

2013-12-31

Data from the literature suggest that the rebound of a drop from a surface can be achieved when the wettability is low, i.e., when contact angles, measured at the triple line (solid-liquid-air), are high. However, no clear criterion exists to predict when a drop will rebound from a surface and which is the key wetting parameter to govern drop rebound (e.g., the "equilibrium" contact angle, θeq, the advancing and the receding contact angles, θA and θR, respectively, the contact angle hysteresis, Δθ, or any combination of these parameters). To clarify the conditions for drop rebound, we conducted experimental tests on different dry solid surfaces with variable wettability, from hydrophobic to superhydrophobic surfaces, with advancing contact angles 108° < θA < 169° and receding contact angles 89° < θR < 161°. It was found that the receding contact angle is the key wetting parameter that influences drop rebound, along with surface hydrophobicity: for the investigated impact conditions (drop diameter 2.4 < D0 < 2.6 mm, impact speed 0.8 < V < 4.1 m/s, Weber number 25 < We < 585), rebound was observed only on surfaces with receding contact angles higher than 100°. Also, the drop rebound time decreased by increasing the receding contact angle. It was also shown that in general care must be taken when using statically defined wetting parameters (such as advancing and receding contact angles) to predict the dynamic behavior of a liquid on a solid surface because the dynamics of the phenomenon may affect surface wetting close to the impact point (e.g., as a result of the transition from the Cassie-Baxter to Wenzel state in the case of the so-called superhydrophobic surfaces) and thus affect the drop rebound.

Are laboratory tests always needed? Frequency and causes of laboratory overuse in a hospital setting.

PubMed

Cadamuro, Janne; Gaksch, Martin; Wiedemann, Helmut; Lippi, Giuseppe; von Meyer, Alexander; Pertersmann, Astrid; Auer, Simon; Mrazek, Cornelia; Kipman, Ulrike; Felder, Thomas K; Oberkofler, Hannes; Haschke-Becher, Elisabeth

2018-04-01

Inappropriate utilization of laboratory resources is an increasing concern especially in high-throughput facilities. Until now, no reliable information has been published addressing to which extent laboratory results are actually used for clinical decision-making. Therefore, we aimed to close this gap using a novel retrospective approach including a survey of clinicians and nurses. We retrospectively evaluated the number of re-orders for potassium (K), lactate dehydrogenase (LD), aspartate-aminotransferase (AST), activated partial thromboplastin-time (APTT) and prothrombin-time/INR (PT/INR), after the initial order had to be cancelled due to preanalytical non-conformities. We analyzed subgroups regarding time to re-order, ward and sample priority (urgent vs. routine). Subsequently, we surveyed clinicians and nurses, asking for their estimate of the amount of failed re-orders as well as for possible reasons. From initially cancelled tests, only ~20% of K, LD, AST and ~30% of APTT and PT/INR tests were re-ordered within 24 h. 70% of the investigated clinical chemistry and 60% of coagulation tests were re-ordered one week after cancellation or not at all. Survey participants quite accurately estimated these numbers. Routine laboratory panels, short stay of out-patients, obsolete test results and avoiding additional phlebotomies were the main reasons for not re-ordering cancelled tests. Overall, 60-70% of test results in the investigated assays ordered in a high throughput laboratory are potentially inappropriate or of doubtful clinically importance. Although clinicians and nurses are aware of this situation, it is the duty of laboratory specialists to overcome overutilization in close collaboration with all involved healthcare workers. Copyright © 2018 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Empirical Determination of Efficient Sensing Frequencies for Magnetometer-Based Continuous Human Contact Monitoring.

PubMed

Kuk, Seungho; Kim, Junha; Park, Yongtae; Kim, Hyogon

2018-04-27

The high linear correlation between the smartphone magnetometer readings in close proximity can be exploited for physical human contact detection, which could be useful for such applications as infectious disease contact tracing or social behavior monitoring. Alternative approaches using other capabilities in smartphones have aspects that do not fit well with the human contact detection. Using Wi-Fi or cellular fingerprints have larger localization errors than close human contact distances. Bluetooth beacons could reveal the identity of the transmitter, threatening the privacy of the user. Also, using sensors such as GPS does not work for indoor contacts. However, the magnetometer correlation check works best in human contact distances that matter in infectious disease transmissions or social interactions. The omni-present geomagnetism makes it work both indoors and outdoors, and the measured magnetometer values do not easily reveal the identity and the location of the smartphone. One issue with the magnetometer-based contact detection, however, is the energy consumption. Since the contacts can take place anytime, the magnetometer sensing and recording should be running continuously. Therefore, how we address the energy requirement for the extended and continuous operation can decide the viability of the whole idea. However, then, we note that almost all existing magnetometer-based applications such as indoor location and navigation have used high sensing frequencies, ranging from 10 Hz to 200 Hz. At these frequencies, we measure that the time to complete battery drain in a typical smartphone is shortened by three to twelve hours. The heavy toll raises the question as to whether the magnetometer-based contact detection can avoid such high sensing rates while not losing the contact detection accuracy. In order to answer the question, we conduct a measurement-based study using independently produced magnetometer traces from three different countries. Specifically, we

Empirical Determination of Efficient Sensing Frequencies for Magnetometer-Based Continuous Human Contact Monitoring

PubMed Central

Kuk, Seungho; Kim, Junha; Park, Yongtae; Kim, Hyogon

2018-01-01

The high linear correlation between the smartphone magnetometer readings in close proximity can be exploited for physical human contact detection, which could be useful for such applications as infectious disease contact tracing or social behavior monitoring. Alternative approaches using other capabilities in smartphones have aspects that do not fit well with the human contact detection. Using Wi-Fi or cellular fingerprints have larger localization errors than close human contact distances. Bluetooth beacons could reveal the identity of the transmitter, threatening the privacy of the user. Also, using sensors such as GPS does not work for indoor contacts. However, the magnetometer correlation check works best in human contact distances that matter in infectious disease transmissions or social interactions. The omni-present geomagnetism makes it work both indoors and outdoors, and the measured magnetometer values do not easily reveal the identity and the location of the smartphone. One issue with the magnetometer-based contact detection, however, is the energy consumption. Since the contacts can take place anytime, the magnetometer sensing and recording should be running continuously. Therefore, how we address the energy requirement for the extended and continuous operation can decide the viability of the whole idea. However, then, we note that almost all existing magnetometer-based applications such as indoor location and navigation have used high sensing frequencies, ranging from 10 Hz to 200 Hz. At these frequencies, we measure that the time to complete battery drain in a typical smartphone is shortened by three to twelve hours. The heavy toll raises the question as to whether the magnetometer-based contact detection can avoid such high sensing rates while not losing the contact detection accuracy. In order to answer the question, we conduct a measurement-based study using independently produced magnetometer traces from three different countries. Specifically, we

Tribological investigations of the load, temperature, and time dependence of wear in sliding contact.

PubMed

Marko, Matthew David; Kyle, Jonathan P; Wang, Yuanyuan Sabrina; Terrell, Elon J

2017-01-01

An effort was made to study and characterize the evolution of transient tribological wear in the presence of sliding contact. Sliding contact is often characterized experimentally via the standard ASTM D4172 four-ball test, and these tests were conducted for varying times ranging from 10 seconds to 1 hour, as well as at varying temperatures and loads. A numerical model was developed to simulate the evolution of wear in the elastohydrodynamic regime. This model uses the results of a Monte Carlo study to develop novel empirical equations for wear rate as a function of asperity height and lubricant thickness; these equations closely represented the experimental data and successfully modeled the sliding contact.

Contact frequency and cognitive health among older adults in Israel.

PubMed

Schwartz, Ella; Khalaila, Rabia; Litwin, Howard

2018-05-03

The current study set out to examine the links between contact frequency with one's social network and cognitive health in later life. It assessed both direct and indirect pathways and the possible role of ethnicity in the effect of the social network on cognitive function. We used data from adults aged 50 and above, which was collected in Israel as part of the Survey of Ageing, Retirement and Health (SHARE). A moderated mediation analysis was conducted to test the direct and indirect associations between contact frequency and cognitive function, as well as the moderation of these associations by population group. Three population groups were examined - veteran-Jews, Arabs and immigrants from the former Soviet Union. Contact frequency with the close social milieu was found to be directly positively related to cognitive function. The association was also mediated by depressive symptoms, such that frequent contacts were linked to cognitive health via reduced depressive symptoms. This indirect link differed, however, among the three population groups. Contact frequency is important for cognitive health in the second half of life, and it operates both directly and by decreasing depressive symptoms. However, these links are not found among all ethnic groups and may, therefore, depend on the culture and social norms of each group and the meaning attributed to social ties.

Microbiological Laboratory Hazard of Bearded Men

PubMed Central

Barbeito, Manuel S.; Mathews, Charles T.; Taylor, Larry A.

1967-01-01

An investigation was conducted to evaluate the hypothesis that a bearded man subjects his family and friends to risk of infection if his beard is contaminated by infectious microorganisms while he is working in a microbiological laboratory. Bearded and unbearded men were tested with Serratia marcescens and Bacillus subtilis var. niger. Contact aerosol transmission from a contaminated beard on a mannequin to a suitable host was evaluated with both Newcastle disease virus and Clostridium botulinum toxin, type A. The experiments showed that beards retained microorganisms and toxin despite washing with soap and water. Although washing reduced the amount of virus or toxin, a sufficient amount remained to produce disease upon contact with a suitable host. Images Fig. 1 Fig. 2 Fig. 3 PMID:4963447

Robust classification of contact orientation between tissue and an integrated spectroscopy and radiofrequency ablation catheter

NASA Astrophysics Data System (ADS)

Zaryab, Mohammad; Singh-Moon, Rajinder P.; Hendon, Christine P.

2017-02-01

Using light-based catheters for radiofrequency ablation (RFA) therapies grants the ability to accurately derive tissue properties such as lesion depth and overtreatment from spectroscopic information. However, this information is heavily reliant on contact quality with the treatment area and the orientation of the catheter. Thus to improve assessments of tissue properties, this work utilizes Bayesian modelling to classify whether the catheter is indeed in proper contact with the tissue. Initially in-laboratory experiments were conducted with ten fresh swine hearts submerged in blood. A total of 1555 unique near infrared spectra were collected from a spectrometer using a light-based catheter and manually tagged as "full perpendicular contact," "angled contact," and "no contact," between the catheter and heart tissue. Three features were prominent in all spectra for distinguishing purposes: area underneath the spectra, an intensity "valley" between 730 nm and 800 nm, along with the slope between 850 nm and 1150 nm. A classifier featuring bootstrapping, adaboost, and k-means techniques was thus created and achieved a 96.05% accuracy in classifying full contact, 98.33% accuracy in classifying angled contact, and 100% accuracy in classifying no contact.

Limits on light weakly interacting massive particles from the CDEX-1 experiment with a p -type point-contact germanium detector at the China Jinping Underground Laboratory

NASA Astrophysics Data System (ADS)

Yue, Q.; Zhao, W.; Kang, K. J.; Cheng, J. P.; Li, Y. J.; Lin, S. T.; Chang, J. P.; Chen, N.; Chen, Q. H.; Chen, Y. H.; Chuang, Y. C.; Deng, Z.; Du, Q.; Gong, H.; Hao, X. Q.; He, H. J.; He, Q. J.; Huang, H. X.; Huang, T. R.; Jiang, H.; Li, H. B.; Li, J. M.; Li, J.; Li, J.; Li, X.; Li, X. Y.; Li, Y. L.; Liao, H. Y.; Lin, F. K.; Liu, S. K.; Lü, L. C.; Ma, H.; Mao, S. J.; Qin, J. Q.; Ren, J.; Ren, J.; Ruan, X. C.; Shen, M. B.; Singh, L.; Singh, M. K.; Soma, A. K.; Su, J.; Tang, C. J.; Tseng, C. H.; Wang, J. M.; Wang, L.; Wang, Q.; Wong, H. T.; Wu, S. Y.; Wu, Y. C.; Wu, Y. C.; Xianyu, Z. Z.; Xiao, R. Q.; Xing, H. Y.; Xu, F. Z.; Xu, Y.; Xu, X. J.; Xue, T.; Yang, L. T.; Yang, S. W.; Yi, N.; Yu, C. X.; Yu, H.; Yu, X. Z.; Zeng, X. H.; Zeng, Z.; Zhang, L.; Zhang, Y. H.; Zhao, M. G.; Zhou, Z. Y.; Zhu, J. J.; Zhu, W. B.; Zhu, X. Z.; Zhu, Z. H.; CDEX Collaboration

2014-11-01

We report results of a search for light dark matter weakly interacting massive particles (WIMPs) with CDEX-1 experiment at the China Jinping Underground Laboratory, based on 53.9 kg-days of data from a p -type point-contact germanium detector enclosed by a NaI(Tl) crystal scintillator as anti-Compton detector. The event rate and spectrum above the analysis threshold of 475 eVee are consistent with the understood background model. Part of the allowed regions for WIMP-nucleus coherent elastic scattering at WIMP mass of 6-20 GeV are probed and excluded. Independent of interaction channels, this result contradicts the interpretation that the anomalous excesses of the CoGeNT experiment are induced by dark matter, since identical detector techniques are used in both experiments.

77 FR 33752 - National Center for Advancing Translational Sciences; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-07

... Advancing Translational Sciences; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Center for Advancing...). Contact Person: Barbara J. Nelson, Ph.D., Scientific Review Officer, Office of Grants Management...

Phosphatidylserine synthesis at membrane contact sites promotes its transport out of the ER.

PubMed

Kannan, Muthukumar; Lahiri, Sujoy; Liu, Li-Ka; Choudhary, Vineet; Prinz, William A

2017-03-01

Close contacts between organelles, often called membrane contact sites (MCSs), are regions where lipids are exchanged between organelles. Here, we identify a novel mechanism by which cells promote phospholipid exchange at MCSs. Previous studies have shown that phosphatidylserine (PS) synthase activity is highly enriched in portions of the endoplasmic reticulum (ER) in contact with mitochondria. The objective of this study was to determine whether this enrichment promotes PS transport out of the ER. We found that PS transport to mitochondria was more efficient when PS synthase was fused to a protein in the ER at ER-mitochondria contacts than when it was fused to a protein in all portions of the ER. Inefficient PS transport to mitochondria was corrected by increasing tethering between these organelles. PS transport to endosomes was similarly enhanced by PS production in regions of the ER in contact with endosomes. Together, these findings indicate that PS production at MCSs promotes PS transport out of the ER and suggest that phospholipid production at MCSs may be a general mechanism of channeling lipids to specific cellular compartments.

Insecticidal effects of deltamethrin in laboratory and field populations of Culicoides species: how effective are host-contact reduction methods in India?

PubMed

De Keyser, Rien; Cassidy, Clare; Laban, Swathi; Gopal, Prakash; Pickett, John A; Reddy, Yarabolu K; Prasad, Minakshi; Prasad, Gaya; Chirukandoth, Sreekumar; Senthilven, Kandasamy; Carpenter, Simon; Logan, James G

2017-01-31

Bluetongue virus (BTV) is transmitted by Culicoides biting midges and causes bluetongue (BT), a clinical disease observed primarily in sheep. BT has a detrimental effect on subsistence farmers in India, where hyperendemic outbreaks impact on smallholdings in the southern states of the country. In this study, we establish a reliable method for testing the toxic effects of deltamethrin on Culicoides and then compare deltamethrin with traditional control methods used by farmers in India. Effects of deltamethrin were initially tested using a colonised strain of Culicoides nubeculosus Meigen and a modified World Health Organisation exposure assay. This method was then applied to field populations of Culicoides spp. in India. The field population of C. oxystoma in India had a greater LC 50 (0.012 ± 0.009%) for deltamethrin than laboratory-reared C.nubeculosus (0.0013 ± 0.0002%). Exposure of C. nubeculosus to deltamethrin at higher ambient temperatures resulted in greater rates of knockdown but a lower mortality rate at 24 h post-exposure. Behavioural assays with C. nubeculosus in WHO tubes provided evidence for contact irritancy and spatial repellence caused by deltamethrin. The field experiments in India, however, provided no evidence for repellent or toxic effects of deltamethrin. Traditional methods such as the application of neem oil and burning of neem leaves also provided no protection. Our study demonstrates that field-collected Culicoides in India are less susceptible to deltamethrin exposure than laboratory-bred C. nubeculosus and traditional methods of insect control do not provide protection to sheep. These low levels of susceptibility to deltamethrin have not been recorded before in field populations of Culicoides and suggest resistance to synthetic pyrethrioids. Alternative insect control methods, in addition to vaccination, may be needed to protect Indian livestock from BTV transmission.

Contact force structure and force chains in 3D sheared granular systems

NASA Astrophysics Data System (ADS)

Mair, Karen; Jettestuen, Espen; Abe, Steffen

2010-05-01

Faults often exhibit accumulations of granular debris, ground up to create a layer of rock flour or fault gouge separating the rigid fault walls. Numerical simulations and laboratory experiments of sheared granular materials, suggest that applied loads are preferentially transmitted across such systems by transient force networks that carry enhanced forces. The characterisation of such features is important since their nature and persistence almost certainly influence the macroscopic mechanical stability of these systems and potentially that of natural faults. 3D numerical simulations of granular shear are a valuable investigation tool since they allow us to track individual particle motions, contact forces and their evolution during applied shear, that are difficult to view directly in laboratory experiments or natural fault zones. In characterising contact force distributions, it is important to use global structure measures that allow meaningful comparisons of granular systems having e.g. different grain size distributions, as may be expected at different stages of a fault's evolution. We therefore use a series of simple measures to characterise the structure, such as distributions and correlations of contact forces that can be mapped onto a force network percolation problem as recently proposed by Ostojic and coworkers for 2D granular systems. This allows the use of measures from percolation theory to both define and characterise the force networks. We demonstrate the application of this method to 3D simulations of a sheared granular material. Importantly, we then compare our measure of the contact force structure with macroscopic frictional behaviour measured at the boundaries of our model to determine the influence of the force networks on macroscopic mechanical stability.

A model undergraduate research institute for study of emerging non-contact measurement technologies and techniques

NASA Astrophysics Data System (ADS)

Dvonch, Curt; Smith, Christopher; Bourne, Stefanie; Blandino, Joseph R.; Miles, Jonathan J.

2006-04-01

The Infrared Development and Thermal Structures Laboratory (IDTSL) is an undergraduate research laboratory in the College of Integrated Science and Technology (CISAT) at James Madison University (JMU) in Harrisonburg, Virginia. During the 1997-98 academic year, Dr. Jonathan Miles established the IDTSL at JMU with the support of a collaborative research grant from the NASA Langley Research Center and with additional support from the College of Integrated Science and Technology at JMU. The IDTSL supports research and development efforts that feature non-contact thermal and mechanical measurements and advance the state of the art. These efforts all entail undergraduate participation intended to significantly enrich their technical education. The IDTSL is funded by major government organizations and the private sector and provides a unique opportunity to undergraduates who wish to participate in projects that push the boundaries of non-contact measurement technologies, and provides a model for effective hands-on, project oriented, student-centered learning that reinforces concepts and skills introduced within the Integrated Science and Technology (ISAT) curriculum. The lab also provides access to advanced topics and emerging measurement technologies; fosters development of teaming and communication skills in an interdisciplinary environment; and avails undergraduates of professional activities including writing papers, presentation at conferences, and participation in summer internships. This paper provides an overview of the Infrared Development and Thermal Structures Laboratory, its functionality, its record of achievements, and the important contribution it has made to the field of non-contact measurement and undergraduate education.

Thermal singularity and contact line motion in pool boiling: Effects of substrate wettability.

PubMed

Taylor, M T; Qian, Tiezheng

2016-03-01

The dynamic van der Waals theory [Phys. Rev. E 75, 036304 (2007)] is employed to model the growth of a single vapor bubble in a superheated liquid on a flat homogeneous substrate. The bubble spreading dynamics in the pool boiling regime has been numerically investigated for one-component van der Waals fluids close to the critical point, with a focus on the effect of the substrate wettability on bubble growth and contact line motion. The substrate wettability is found to control the apparent contact angle and the rate of bubble growth (the rate of total evaporation), through which the contact line speed is determined. An approximate expression is derived for the contact line speed, showing good agreement with the simulation results. This demonstrates that the contact line speed is primarily governed by (1) the circular shape of interface (for slow bubble growth), (2) the constant apparent contact angle, and (3) the constant bubble growth rate. It follows that the contact line speed has a sensitive dependence on the substrate wettability via the apparent contact angle which also determines the bubble growth rate. Compared to hydrophilic surfaces, hydrophobic surfaces give rise to a thinner shape of bubble and a higher rate of total evaporation, which combine to result in a much faster contact line speed. This can be linked to the earlier formation of a vapor film and hence the onset of boiling crisis.

Clonal Differences between Non-Typhoidal Salmonella (NTS) Recovered from Children and Animals Living in Close Contact in The Gambia

PubMed Central

Dione, Michel M.; Ikumapayi, Usman N.; Saha, Debasish; Mohammed, Nuredin I.; Geerts, Stanny; Ieven, Margareta; Adegbola, Richard A.; Antonio, Martin

2011-01-01

Background Non-Typhoidal Salmonella (NTS) is an important cause of invasive bacterial disease and associated with mortality in Africa. However, little is known about the environmental reservoirs and predominant modes of transmission. Our study aimed to study the role of domestic animals in the transmission of NTS to humans in rural area of The Gambia. Methodology Human NTS isolates were obtained through an active population-based case-control surveillance study designated to determine the aetiology and epidemiology of enteric infections covering 27,567 Gambian children less than five years of age in the surveillance area. Fourteen children infected with NTS were traced back to their family compounds and anal swabs collected from 210 domestic animals present in their households. Identified NTSs were serotyped and genotyped by multi-locus sequencing typing. Principal Findings NTS was identified from 21/210 animal sources in the households of the 14 infected children. Chickens carried NTS more frequently than sheep and goats; 66.6%, 28.6% and 4.8% respectively. The most common NTS serovars were S. Colindale in humans (21.42%) and S. Poona in animals (14.28%). MLST on the 35 NTS revealed four new alleles and 24 sequence types (ST) of which 18 (75%) STs were novel. There was no overlap in serovars or genotypes of NTS recovered from humans or animal sources in the same household. Conclusion Our results do not support the hypothesis that humans and animals in close contact in the same household carry genotypically similar Salmonella serovars. These findings form an important baseline for future studies of transmission of NTS in humans and animals in Africa. PMID:21655353

20 CFR 220.113 - Symptoms, signs, and laboratory findings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Symptoms, signs, and laboratory findings. 220.113 Section 220.113 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD..., thought, memory, orientation and contact with reality. They must also be shown by observable facts that...

78 FR 13358 - National Institute of Environmental Health Sciences Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-27

... Environmental Health Sciences Notice of Closed Meetings Pursuant to section 10(d) of the Federal Advisory... Health Sciences Special Emphasis Panel Research Careers in Environmental Health. Date: March 19, 2013... Conference Call). Contact Person: Linda K Bass, Scientific Review Officer, Scientific Review Branch, Division...

Contact Us | NREL

Science.gov Websites

Contact Us Contact Us Find a contact to help answer your question, resolve a website issue, or job or internship, or want to report an issue with the application process, contact us about careers

Contact us

Science.gov Websites

DCIO R&A DCIO CS In the News Library Contact us contact us Contact the Department of Defense Public Queries for DOD General questions or comments concerning the DOD Veteran Affairs Public questions or comments concerning the Department of Veterans Affairs (VA) Army Public questions or comments concerning

Food and Drug Administration: Insufficient Planning for Field Laboratory Consolidation Decisions.

DTIC Science & Technology

1987-12-04

adequately 5 address whether FDA could meet its current and future laboratory needs if the five laboratories were closed or whether cost- effective ...pie transit and laboratory processing times would lessen FDA’S regula- tory effectiveness . Moreover, 61 percent of the excess laboratory capacity...FDA believes that it can ship sam- pies from across the nation to almost any location for analysis without reducing its regulatory effectiveness . (See

Finite Source Inversion for Laboratory Earthquakes

NASA Astrophysics Data System (ADS)

Parker, J. M.; Glaser, S. D.

2017-12-01

We produce finite source inversion results for laboratory earthquakes (LEQ) in PMMA confirmed by video recording of the fault contact. The LEQs are generated under highly controlled laboratory conditions and recorded by an array of absolutely calibrated acoustic emissions (AE) sensors. Following the method of Hartzell and Heaton (1983), we develop a solution using only the single-component AE sensors common in laboratory experiments. A set of calibration tests using glass capillary sources of varying size resolves the material characteristics and synthetic Green's Functions such that uncertainty in source location is reduced to 3σ<1mm; typical source radii are 1mm. Well-isolated events with corner frequencies on the order of 0.1 MHz (Mw -6) are recorded at 20 MHz and initially band-pass filtered from 0.1 to 1.0 MHz; in comparison, large earthquakes with corner frequencies around 0.1 Hz are commonly filtered from 0.1 to 1.0 Hz. We compare results of the inversion and video recording to slip distribution predicted by the Cattaneo partial slip asperity and numerical modeling. Not all asperities are large enough to resolve individually so some results must be interpreted as the smoothed effects of clusters of tiny contacts. For large asperities, partial slip is observed originating at the asperity edges and moving inward as predicted by the theory. Furthermore, expanding shear rupture fronts are observed as they reach resistive patches of asperities and halt or continue, depending on the relative energies of rupture and resistance.

The dependency paradox in close relationships: accepting dependence promotes independence.

PubMed

Feeney, Brooke C

2007-02-01

Using multiple methods, this investigation tested the hypothesis that a close relationship partner's acceptance of dependence when needed (e.g., sensitive responsiveness to distress cues) is associated with less dependence, more autonomous functioning, and more self-sufficiency (as opposed to more dependence) on the part of the supported individual. In two studies, measures of acceptance of dependency needs and independent functioning were obtained through couple member reports, by observing couple members' behaviors during laboratory interactions, by observing responses to experimentally manipulated partner assistance provided during an individual laboratory task, and by following couples over a period of 6 months to examine independent goal striving as a function of prior assessments of dependency acceptance. Results provided converging evidence in support of the proposed hypothesis. Implications of the importance of close relationships for optimal individual functioning are discussed. ((c) 2007 APA, all rights reserved).

Lack of a close confidant: prevalence and correlates in a medically underserved primary care sample.

PubMed

Newton, Tamara; Buckley, Amy; Zurlage, Megan; Mitchell, Charlene; Shaw, Ann; Woodruff-Borden, Janet

2008-03-01

The present study examined prevalence of lack of a close confidant in a medically underserved primary care sample, and evaluated demographic, medical, and psychological correlates of patients' deficits in close, personal contact. Adult patients (n = 413) reported on confidant status and symptoms of depression and anxiety. Sociodemographic and medical information were obtained through chart review. One-quarter of patients endorsed lack of a close confidant. Past month anxiety and depression symptoms, but not medical status, were associated with unmet socioemotional needs. Implications for primary healthcare interventions are discussed.

Mitigation of epidemics in contact networks through optimal contact adaptation.

PubMed

Youssef, Mina; Scoglio, Caterina

2013-08-01

This paper presents an optimal control problem formulation to minimize the total number of infection cases during the spread of susceptible-infected-recovered SIR epidemics in contact networks. In the new approach, contact weighted are reduced among nodes and a global minimum contact level is preserved in the network. In addition, the infection cost and the cost associated with the contact reduction are linearly combined in a single objective function. Hence, the optimal control formulation addresses the tradeoff between minimization of total infection cases and minimization of contact weights reduction. Using Pontryagin theorem, the obtained solution is a unique candidate representing the dynamical weighted contact network. To find the near-optimal solution in a decentralized way, we propose two heuristics based on Bang-Bang control function and on a piecewise nonlinear control function, respectively. We perform extensive simulations to evaluate the two heuristics on different networks. Our results show that the piecewise nonlinear control function outperforms the well-known Bang-Bang control function in minimizing both the total number of infection cases and the reduction of contact weights. Finally, our results show awareness of the infection level at which the mitigation strategies are effectively applied to the contact weights.

Measuring contact area in a sliding human finger-pad contact.

PubMed

Liu, X; Carré, M J; Zhang, Q; Lu, Z; Matcher, S J; Lewis, R

2018-02-01

The work outlined in this paper was aimed at achieving further understanding of skin frictional behaviour by investigating the contact area between human finger-pads and flat surfaces. Both the static and the dynamic contact areas (in macro- and micro-scales) were measured using various techniques, including ink printing, optical coherence tomography (OCT) and Digital Image Correlation (DIC). In the studies of the static measurements using ink printing, the experimental results showed that the apparent and the real contact area increased with load following a piecewise linear correlation function for a finger-pad in contact with paper sheets. Comparisons indicated that the OCT method is a reliable and effective method to investigate the real contact area of a finger-pad and allow micro-scale analysis. The apparent contact area (from the DIC measurements) was found to reduce with time in the transition from the static phase to the dynamic phase while the real area of contact (from OCT) increased. The results from this study enable the interaction between finger-pads and contact object surface to be better analysed, and hence improve the understanding of skin friction. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

A non-contact temperature measurement system for controlling photothermal medical laser treatments

NASA Astrophysics Data System (ADS)

Kaya, Ã.-zgür; Gülsoy, Murat

2016-03-01

Photothermal medical laser treatments are extremely dependent on the generated tissue temperature. It is necessary to reach a certain temperature threshold to achieve successful results, whereas preventing to exceed an upper temperature value is required to avoid thermal damage. One method to overcome this problem is to use previously conducted dosimetry studies as a reference. Nevertheless, these results are acquired in controlled environments using uniform subjects. In the clinical environment, the optical and thermal characteristics (tissue color, composition and hydration level) vary dramatically among different patients. Therefore, the most reliable solution is to use a closed-loop feedback system that monitors the target tissue temperature to control laser exposure. In this study, we present a compact, non-contact temperature measurement system for the control of photothermal medical laser applications that is cost-efficient and simple to use. The temperature measurement is achieved using a focused, commercially available MOEMS infrared thermocouple sensor embedded in an off-axis arrangement on the laser beam delivery hand probe. The spot size of the temperature sensor is ca. 2.5 mm, reasonably smaller than the laser spot sizes used in photothermal medical laser applications. The temperature readout and laser control is realized using a microcontroller for fast operation. The utilization of the developed system may enable the adaptation of several medical laser treatments that are currently conducted only in controlled laboratory environments into the clinic. Laser tissue welding and cartilage reshaping are two of the techniques that are limited to laboratory research at the moment. This system will also ensure the safety and success of laser treatments aiming hyperthermia, coagulation and ablation, as well as LLLT and PDT.

Renewable Water: Direct Contact Membrane Distillation Coupled With Solar Ponds

NASA Astrophysics Data System (ADS)

Suarez, F. I.; Tyler, S. W.; Childress, A. E.

2010-12-01

The exponential population growth and the accelerated increase in the standard of living have increased significantly the global consumption of two precious resources: water and energy. These resources are intrinsically linked and are required to allow a high quality of human life. With sufficient energy, water may be harvested from aquifers, treated for potable reuse, or desalinated from brackish and seawater supplies. Even though the costs of desalination have declined significantly, traditional desalination systems still require large quantities of energy, typically from fossil fuels that will not allow these systems to produce water in a sustainable way. Recent advances in direct contact membrane distillation can take advantage of low-quality or renewable heat to desalinate brackish water, seawater or wastewater. Direct contact membrane distillation operates at low pressures and can use small temperature differences between the feed and permeate water to achieve a significant freshwater production. Therefore, a much broader selection of energy sources can be considered to drive thermal desalination. A promising method for providing renewable source of heat for direct contact membrane distillation is a solar pond, which is an artificially stratified water body that captures solar radiation and stores it as thermal energy at the bottom of the pond. In this work, a direct contact membrane distillation/solar pond coupled system is modeled and tested using a laboratory-scale system. Freshwater production rates on the order of 2 L day-1 per m2 of solar pond (1 L hr-1 per m2 of membrane area) can easily be achieved with minimal operating costs and under low pressures. While these rates are modest, they are six times larger than those produced by other solar pond-powered desalination systems - and they are likely to be increased if heat losses in the laboratory-scale system are reduced. Even more, this system operates at much lower costs than traditional desalination

Atmospheric dynamics of combined crops of wheat, cowpea, pinto beans in the Laboratory Biosphere closed ecological system

NASA Astrophysics Data System (ADS)

Dempster, W.; Nelson, M.; Silverstone, S.; Allen, J.; Alling, A.; van Thillo, M.

A mixed crop consisting of cowpeas pinto beans and Apogee ultra-dwarf wheat was grown in Laboratory Biosphere a 40 m 3 closed life system equipped with 12000 watts of high pressure sodium lamps over planting beds with 5 37 m 2 of soil Similar to earlier reported experiments the concentration of carbon dioxide initially increased to 7860 ppm at 10 days after planting due to soil respiration plus CO 2 contributed from researchers breathing while in the chamber for brief periods before plant growth became substantial fell rapidly as plant growth increased up to 29 days after planting and then was maintained mostly in the range of about 200 -- 3000 ppm with a few excursions by CO 2 injections to feed plant growth Numerous analyses of rate of change of CO 2 concentration at many different concentrations and at many different days after planting reveals a strong dependence of fixation rates on CO 2 concentration In the middle period of growth days 31 -- 61 fixation rates doubled for CO 2 at 450 ppm compared to 270 ppm doubled again at 1000 ppm and increased a further 50 at 2040 ppm High productivity from these crops and the increase of fixation rates with elevated CO 2 concentration supports the concept that enhanced CO2 can be a useful strategy for remote life support systems

Four Argonne National Laboratory scientists receive Early Career Research

Science.gov Websites

Media Contacts Social Media Photos Videos Fact Sheets, Brochures and Reports Summer Science Writing Writing Internship Four Argonne National Laboratory scientists receive Early Career Research Program economic impact of cascading shortages. He will also seek to enable scaling on high-performance computing

Contact lens complications.

PubMed

Suchecki, Jeanine K; Donshik, Peter; Ehlers, William H

2003-09-01

Complications associated with contact lenses range from mild to severe and occur with all lens modalities. Contact lens wear can cause a change in corneal physiology, which can lead to epithelial, stromal, and endothelial compromise. Other complications include lens deposition, allergic conjunctivitis, giant papillary conjunctivitis, peripheral infiltrates, microbial keratitis, and neovascularization. Pre-existing conditions can contribute to these complications, or they can occur in association with contact lens wear and care regimens. Patient-related factors, such as alteration of the recommended wearing or replacement schedules and noncompliance with recommended contact lens care regimens for economic reasons, convenience, or in error, contribute to contact lens-related complications and have led to difficulty in accurate determination of complication rates among the various lens wear modalities. Complications may require discontinuation of contact lenses, topical therapy, and changes in contact lens wearing schedules, materials, and care solutions. On initial lens fitting and follow-up evaluations, practitioners should review contact lens replacement and cleaning regimens with patients and discuss complications. To avoid serious complications, patients should be reminded to remove their contact lenses as soon as ocular irritation occurs, and to call their eye care practitioner immediately if symptoms persist.

Activity-dependent decrease in contact areas between subsurface cisterns and plasma membrane of hippocampal neurons.

PubMed

Tao-Cheng, Jung-Hwa

2018-04-16

Subsurface cistern (SSC) in neuronal soma and primary dendrites is a specialized compartment of endoplasmic reticulum (ER) that is in close apposition (10 nm) with the plasma membrane (PM). ER-PM contact areas are thought to be involved in intracellular calcium regulation. Here, structural changes of SSC in hippocampal neurons were examined by electron microscopy upon depolarization with high K + (90 mM) or application of NMDA (50 μM) in rat dissociated cultures as well as organotypic slice cultures. The number and average length of SSC-PM contact areas in neuronal somas significantly decreased within 30 s under excitatory condition. This decrease in SSC-PM contact area progressed with time and was reversible. These results demonstrate a structural decoupling between the SSC and the PM upon stimulation, suggesting that there may be a functional decoupling of the calcium regulation. Because SSC-PM contact areas may mediate calcium influx, the decrease in contact area may protect neurons from calcium overload upon heightened stimulation.

NF2/Merlin mediates contact-dependent inhibition of EGFR mobility and internalization via cortical actomyosin.

PubMed

Chiasson-MacKenzie, Christine; Morris, Zachary S; Baca, Quentin; Morris, Brett; Coker, Joanna K; Mirchev, Rossen; Jensen, Anne E; Carey, Thomas; Stott, Shannon L; Golan, David E; McClatchey, Andrea I

2015-10-26

The proliferation of normal cells is inhibited at confluence, but the molecular basis of this phenomenon, known as contact-dependent inhibition of proliferation, is unclear. We previously identified the neurofibromatosis type 2 (NF2) tumor suppressor Merlin as a critical mediator of contact-dependent inhibition of proliferation and specifically found that Merlin inhibits the internalization of, and signaling from, the epidermal growth factor receptor (EGFR) in response to cell contact. Merlin is closely related to the membrane-cytoskeleton linking proteins Ezrin, Radixin, and Moesin, and localization of Merlin to the cortical cytoskeleton is required for contact-dependent regulation of EGFR. We show that Merlin and Ezrin are essential components of a mechanism whereby mechanical forces associated with the establishment of cell-cell junctions are transduced across the cell cortex via the cortical actomyosin cytoskeleton to control the lateral mobility and activity of EGFR, providing novel insight into how cells inhibit mitogenic signaling in response to cell contact. © 2015 Chiassson-MacKenzie et al.

Comparing maximum intercuspal contacts of virtual dental patients and mounted dental casts.

PubMed

Delong, Ralph; Ko, Ching-Chang; Anderson, Gary C; Hodges, James S; Douglas, W H

2002-12-01

Quantitative measures of occlusal contacts are of paramount importance in the study of chewing dysfunction. A tool is needed to identify and quantify occlusal parameters without occlusal interference caused by the technique of analysis. This laboratory simulation study compared occlusal contacts constructed from 3-dimensional images of dental casts and interocclusal records with contacts found by use of conventional methods. Dental casts of 10 completely dentate adults were mounted in a semi-adjustable Denar articulator. Maximum intercuspal contacts were marked on the casts using red film. Intercuspal records made with an experimental vinyl polysiloxane impression material recorded maximum intercuspation. Three-dimensional virtual models of the casts and interocclusal records were made using custom software and an optical scanner. Contacts were calculated between virtual casts aligned manually (CM), aligned with interocclusal records scanned seated on the mandibular casts (C1) or scanned independently (C2), and directly from virtual interocclusal records (IR). Sensitivity and specificity calculations used the marked contacts as the standard. Contact parameters were compared between method pairs. Statistical comparisons used analysis of variance and the Tukey-Kramer post hoc test (P=<.05). Sensitivities (range 0.76-0.89) did not differ significantly among the 4 methods (P=.14); however, specificities (range 0.89-0.98) were significantly lower for IR (P=.0001). Contact parameters of methods CM, C1, and C2 differed significantly from those of method IR (P<.02). The ranking based on method pair comparisons was C2/C1 > CM/C1 = CM/C2 > C2/IR > CM/IR > C1/IR, where ">" means "closer than." Within the limits of this study, occlusal contacts calculated from aligned virtual casts accurately reproduce articulator contacts.

78 FR 38065 - National Institute of Arthritis and Musculoskeletal and Skin Diseases; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-25

... meeting. The meeting will be closed to the public in accordance with the provisions set forth in sections.... Contact Person: Charles H Washabaugh, Ph.D., Scientific Review Officer, Scientific Review Branch, NIAMS...

External quality assessment of medical laboratories in Croatia: preliminary evaluation of post-analytical laboratory testing.

PubMed

Krleza, Jasna Lenicek; Dorotic, Adrijana; Grzunov, Ana

2017-02-15

Proper standardization of laboratory testing requires assessment of performance after the tests are performed, known as the post-analytical phase. A nationwide external quality assessment (EQA) scheme implemented in Croatia in 2014 includes a questionnaire on post-analytical practices, and the present study examined laboratory responses in order to identify current post-analytical phase practices and identify areas for improvement. In four EQA exercises between September 2014 and December 2015, 145-174 medical laboratories across Croatia were surveyed using the Module 11 questionnaire on the post-analytical phase of testing. Based on their responses, the laboratories were evaluated on four quality indicators: turnaround time (TAT), critical values, interpretative comments and procedures in the event of abnormal results. Results were presented as absolute numbers and percentages. Just over half of laboratories (56.3%) monitored TAT. Laboratories varied substantially in how they dealt with critical values. Most laboratories (65-97%) issued interpretative comments with test results. One third of medical laboratories (30.6-33.3%) issued abnormal test results without confirming them in additional testing. Our results suggest that the nationwide post-analytical EQA scheme launched in 2014 in Croatia has yet to be implemented to the full. To close the gaps between existing recommendations and laboratory practice, laboratory professionals should focus on ensuring that TAT is monitored and lists of critical values are established within laboratories. Professional bodies/institutions should focus on clarify and harmonized rules to standardized practices and applied for adding interpretative comments to laboratory test results and for dealing with abnormal test results.

Intelligent software for laboratory automation.

PubMed

Whelan, Ken E; King, Ross D

2004-09-01

The automation of laboratory techniques has greatly increased the number of experiments that can be carried out in the chemical and biological sciences. Until recently, this automation has focused primarily on improving hardware. Here we argue that future advances will concentrate on intelligent software to integrate physical experimentation and results analysis with hypothesis formulation and experiment planning. To illustrate our thesis, we describe the 'Robot Scientist' - the first physically implemented example of such a closed loop system. In the Robot Scientist, experimentation is performed by a laboratory robot, hypotheses concerning the results are generated by machine learning and experiments are allocated and selected by a combination of techniques derived from artificial intelligence research. The performance of the Robot Scientist has been evaluated by a rediscovery task based on yeast functional genomics. The Robot Scientist is proof that the integration of programmable laboratory hardware and intelligent software can be used to develop increasingly automated laboratories.

Enhanced End-Contacts by Helium Ion Bombardment to Improve Graphene-Metal Contacts

PubMed Central

Jia, Kunpeng; Su, Yajuan; Zhan, Jun; Shahzad, Kashif; Zhu, Huilong; Zhao, Chao; Luo, Jun

2016-01-01

Low contact resistance between graphene and metals is of paramount importance to fabricate high performance graphene-based devices. In this paper, the impact of both defects induced by helium ion (He+) bombardment and annealing on the contact resistance between graphene and various metals (Ag, Pd, and Pt) were systematically explored. It is found that the contact resistances between all metals and graphene are remarkably reduced after annealing, indicating that not only chemically adsorbed metal (Pd) but also physically adsorbed metals (Ag and Pt) readily form end-contacts at intrinsic defect locations in graphene. In order to further improve the contact properties between Ag, Pd, and Pt metals and graphene, a novel method in which self-aligned He+ bombardment to induce exotic defects in graphene and subsequent thermal annealing to form end-contacts was proposed. By using this method, the contact resistance is reduced significantly by 15.1% and 40.1% for Ag/graphene and Pd/graphene contacts with He+ bombardment compared to their counterparts without He+ bombardment. For the Pt/graphene contact, the contact resistance is, however, not reduced as anticipated with He+ bombardment and this might be ascribed to either inappropriate He+ bombardment dose, or inapplicable method of He+ bombardment in reducing contact resistance for Pt/graphene contact. The joint efforts of as-formed end-contacts and excess created defects in graphene are discussed as the cause responsible for the reduction of contact resistance. PMID:28335286

[Patient satisfaction in a laboratory test collection unit].

PubMed

de Moura, Gisela Maria Schebella Souto; Hilleshein, Eunice Fabiani; Schardosim, Juliana Machado; Delgado, Kátia Simone

2008-06-01

This exploratory descriptive study aimed at identifying customer satisfaction attributes in the field of laboratory tests. Data were collected in 2006, using 104 interviews in a laboratorial unit inside a teaching hospital, using the critical incident technique, and submitted to content analysis. Three attribute categories were identified: time spent in waiting for care, interpersonal contact, and technical skills. These results subsidize the assessment of the current satisfaction survey tool, and point to its reformulation. They also allow the identification of improvement needs in customer attention, and provide elements to be taken into account in personnel selection, training programs, personnel performance assessment.

Closing the loop on improvement: Packaging experience in the Software Engineering Laboratory

NASA Technical Reports Server (NTRS)

Waligora, Sharon R.; Landis, Linda C.; Doland, Jerry T.

1994-01-01

As part of its award-winning software process improvement program, the Software Engineering Laboratory (SEL) has developed an effective method for packaging organizational best practices based on real project experience into useful handbooks and training courses. This paper shares the SEL's experience over the past 12 years creating and updating software process handbooks and training courses. It provides cost models and guidelines for successful experience packaging derived from SEL experience.

Mitigation of epidemics in contact networks through optimal contact adaptation *

PubMed Central

Youssef, Mina; Scoglio, Caterina

2013-01-01

This paper presents an optimal control problem formulation to minimize the total number of infection cases during the spread of susceptible-infected-recovered SIR epidemics in contact networks. In the new approach, contact weighted are reduced among nodes and a global minimum contact level is preserved in the network. In addition, the infection cost and the cost associated with the contact reduction are linearly combined in a single objective function. Hence, the optimal control formulation addresses the tradeoff between minimization of total infection cases and minimization of contact weights reduction. Using Pontryagin theorem, the obtained solution is a unique candidate representing the dynamical weighted contact network. To find the near-optimal solution in a decentralized way, we propose two heuristics based on Bang-Bang control function and on a piecewise nonlinear control function, respectively. We perform extensive simulations to evaluate the two heuristics on different networks. Our results show that the piecewise nonlinear control function outperforms the well-known Bang-Bang control function in minimizing both the total number of infection cases and the reduction of contact weights. Finally, our results show awareness of the infection level at which the mitigation strategies are effectively applied to the contact weights. PMID:23906209

Development opportunities for hospital clinical laboratory joint ventures.

PubMed

Van Riper, J A

1995-01-01

Regional health-care providers are being given the opportunity to collaborate in specialty health-care services. Collaboration to achieve superior economies of scale is very effective in the clinical laboratory industry. National laboratory chains are consolidating and enhancing their control of the industry to ensure their historic profitability. National companies have closed many laboratory facilities and have laid off substantial numbers of laboratory personnel. Health-care providers can regain control of their locally generated laboratory health-care dollars by joining forces with clinical laboratory joint ventures. Laboratorians can assist the healthcare providers in bringing laboratory services and employment back to the local community. New capital for operational development and laboratory information systems will help bring the laboratory to the point of care. The independent regional laboratory is focused on supporting the medical needs of the community. The profit generated from a laboratory joint venture is shared among local health-care providers, supporting their economic viability. The laboratories' ability to contribute to the development of profit-making ventures will provide capital for new laboratory development. All of the above will ensure the clinical laboratories' role in providing quality health care to our communities and employment opportunities for laboratory personnel.

LABORATORY CAPACITY NEEDS ASSESSMENT OF DRINKING WATER UTILITIES: A GLOBAL PERSPECTIVE

EPA Science Inventory

Fully-functioning analytical laboratories capable of producing quality data are essential components of well-run drinking water utilities. In Europe and the US, drinking water laboratory performance is closely monitored and regulated; this is not always the case in the less indu...

77 FR 50516 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-21

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical...). Contact Person: Manana Sukhareva, Ph.D., Scientific Review Officer, National Institute of Biomedical...

78 FR 67375 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical... Meeting). Contact Person: Ruth Grossman, DDS, Scientific Review Officer, National Institute of Biomedical...

76 FR 23326 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-26

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical...). Contact Person: Manana Sukhareva, PhD, Scientific Review Officer, National Institute of Biomedical Imaging...

78 FR 67373 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-12

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical... Meeting). Contact Person: Ruth Grossman, DDS, Scientific Review Officer, National Institute of Biomedical...

78 FR 54259 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-03

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical...). Contact Person: Manana Sukhareva, Ph.D., Scientific Review Officer, National Institute of Biomedical...

About Region 3's Laboratory and Field Services at EPA's Environmental Science Center

EPA Pesticide Factsheets

Mission & contact information for EPA Region 3's Laboratory and Field Services located at EPA's Environmental Science Center: the Office of Analytical Services and Quality Assurance & Field Inspection Program

Qualitative identification of rigid gas permeable contact lens materials by densitometry.

PubMed

Arce, C G; Schuman, P D; Schuman, W P

1999-10-01

We describe a practical method to qualitatively identify polymethylmethacrylate (PMMA) and rigid gas permeable (RGP) contact lens materials. By progressive dilution of a saturated saline solution made with distilled or tap water and sodium chloride, we recorded comparative densitometry of rigid contact lens materials using a small hydrometer or by liquid displacement. The method was sensitive enough to separate the polymethylmethacrylate, all silicon-methacrylates, and all but two fluorine-containing silicon-methacrylates. The hydrometer had a precision of three decimals rounded to the nearest 0.005. There was only one RGP product that could have been confused with the PMMA material. Most silicon-methacrylates had lower densities than fluorine containing silicon-methacrylates. Only four of 25 products under 1.117 gm/cm3 contained fluorine. Densitometry with a hydrometer is an effective non-destructive method to identify RGP materials and to verify their quality. The method is easier when lens blanks are tested, but in spite of differences in shape, size, and weight, densitometry may also be used with new or used contact lenses. Its simplicity and low cost makes densitometry feasible for any contact lens laboratory or clinic to use on a routine basis. Only silicon-methacrylates had an inverse relationship between density and oxygen permeability. As the silicon content of the contact lens increases, the Dk increases and the density decreases.

Risk factors for closed-head injuries during military airborne operations.

PubMed

Knapik, Joseph J; Steelman, Ryan; Hoedebecke, Kyle; Klug, Kevin L; Rankin, Shawn; Proctor, Stanley; Graham, Bria; Jones, Bruce H

2014-02-01

One of the more serious adverse outcomes of military airborne operations is closed-head injuries. This investigation examined risk factors for closed-head injuries in an Army airborne infantry unit. Closed-head injuries were defined as energy exchanges in which the head contacted the ground or an object and the soldier sought medical care for external trauma, headache, loss of consciousness, or altered mental state. Injury data were obtained by investigators in the drop zone and diagnoses were confirmed by a physician. Operational data on potential injury risk factors were obtained from routine reports published by the infantry unit. Weather data were obtained using a pocket weather tracker. There were 96,132 jumps resulting in 310 closed-head injuries for a crude incidence of 3.22/1000 jumps. In 98% of known cases the injury was associated with parachute landings. Multivariate logistic regression revealed that independent risk factors for closed-head injuries included night jumps, combat loads, higher wind speeds, higher temperatures, enlisted rank, and entanglements. This study identifies the current incidence and extrinsic risk factors for closed-head injuries during military airborne operations. Although it is necessary to conduct airborne training under realistic conditions, trainers and commanders should be aware of these risks and plan airborne operations accordingly.

Ground Contact Model for Mars Science Laboratory Mission Simulations

NASA Technical Reports Server (NTRS)

Raiszadeh, Behzad; Way, David

2012-01-01

The Program to Optimize Simulated Trajectories II (POST 2) has been successful in simulating the flight of launch vehicles and entry bodies on earth and other planets. POST 2 has been the primary simulation tool for the Entry Descent, and Landing (EDL) phase of numerous Mars lander missions such as Mars Pathfinder in 1997, the twin Mars Exploration Rovers (MER-A and MER-B) in 2004, Mars Phoenix lander in 2007, and it is now the main trajectory simulation tool for Mars Science Laboratory (MSL) in 2012. In all previous missions, the POST 2 simulation ended before ground impact, and a tool other than POST 2 simulated landing dynamics. It would be ideal for one tool to simulate the entire EDL sequence, thus avoiding errors that could be introduced by handing off position, velocity, or other fight parameters from one simulation to the other. The desire to have one continuous end-to-end simulation was the motivation for developing the ground interaction model in POST 2. Rover landing, including the detection of the postlanding state, is a very critical part of the MSL mission, as the EDL landing sequence continues for a few seconds after landing. The method explained in this paper illustrates how a simple ground force interaction model has been added to POST 2, which allows simulation of the entire EDL from atmospheric entry through touchdown.

Types of Contact Lenses

MedlinePlus

... Consumer Devices Consumer Products Contact Lenses Types of Contact Lenses Share Tweet Linkedin Pin it More sharing ... Orthokeratology (Ortho-K) Decorative (Plano) Contact Lenses Soft Contact Lenses Soft contact lenses are made of soft, ...

An outbreak of hepatitis A among primary and secondary contacts of an international adoptee.

PubMed

Pelletier, Andrew R; Mehta, Puja J; Burgess, Donald R; Bondeson, Lisa M; Carson, Patty J; Rea, Vicki E; Sharapov, Umid M; Hu, Dale J

2010-01-01

The Advisory Committee on Immunization Practices recommends that susceptible people traveling to developing countries receive hepatitis A vaccine or immune globulin prior to departure. Until 2009, the recommendations did not address non-traveling family members or other close contacts of international adoptees. We report an outbreak of hepatitis A in 2008 that occurred in Maine. Eight members of an extended family developed hepatitis A following the arrival of an asymptomatic infant from Ethiopia who was brought to the United States by an adoption agency. Two children in the family attended an elementary school where five additional cases of hepatitis A were subsequently identified. Only three (1%) of 208 students at the school had previously been immunized against hepatitis A. This outbreak highlights the need to immunize household members and other close contacts of families adopting children from countries where hepatitis A is endemic, as well as all children at one year of age.

Time reversal invariance for a nonlinear scatterer exhibiting contact acoustic nonlinearity

NASA Astrophysics Data System (ADS)

Blanloeuil, Philippe; Rose, L. R. Francis; Veidt, Martin; Wang, Chun H.

2018-03-01

The time reversal invariance of an ultrasonic plane wave interacting with a contact interface characterized by a unilateral contact law is investigated analytically and numerically. It is shown analytically that despite the contact nonlinearity, the re-emission of a time reversed version of the reflected and transmitted waves can perfectly recover the original pulse shape, thereby demonstrating time reversal invariance for this type of contact acoustic nonlinearity. With the aid of finite element modelling, the time-reversal analysis is extended to finite-size nonlinear scatterers such as closed cracks. The results show that time reversal invariance holds provided that all the additional frequencies generated during the forward propagation, such as higher harmonics, sub-harmonics and zero-frequency component, are fully included in the retro-propagation. If the scattered waves are frequency filtered during receiving or transmitting, such as through the use of narrowband transducers, the recombination of the time-reversed waves will not exactly recover the original incident wave. This discrepancy due to incomplete time invariance can be exploited as a new method for characterizing damage by defining damage indices that quantify the departure from time reversal invariance. The sensitivity of these damage indices for various crack lengths and contact stress levels is investigated computationally, indicating some advantages of this narrowband approach relative to the more conventional measurement of higher harmonic amplitude, which requires broadband transducers.

Experimental investigation on the electrical contact behavior of rolling contact connector.

PubMed

Chen, Junxing; Yang, Fei; Luo, Kaiyu; Zhu, Mingliang; Wu, Yi; Rong, Mingzhe

2015-12-01

Rolling contact connector (RCC) is a new technology utilized in high performance electric power transfer systems with one or more rotating interfaces, such as radars, satellites, wind generators, and medical computed tomography machines. Rolling contact components are used in the RCC instead of traditional sliding contacts to transfer electrical power and/or signal. Since the requirement of the power transmission is increasing in these years, the rolling electrical contact characteristics become more and more important for the long-life design of RCC. In this paper, a typical form of RCC is presented. A series of experimental work are carried out to investigate the rolling electrical contact characteristics during its lifetime. The influence of a variety of factors on the electrical contact degradation behavior of RCC is analyzed under both vacuum and air environment. Based on the surface morphology and elemental composition changes in the contact zone, which are assessed by field emission scanning electron microscope and confocal laser scanning microscope, the mechanism of rolling electrical contact degradation is discussed.

Structures of closed and open conformations of dimeric human ATM

PubMed Central

Baretić, Domagoj; Pollard, Hannah K.; Fisher, David I.; Johnson, Christopher M.; Santhanam, Balaji; Truman, Caroline M.; Kouba, Tomas; Fersht, Alan R.; Phillips, Christopher; Williams, Roger L.

2017-01-01

ATM (ataxia-telangiectasia mutated) is a phosphatidylinositol 3-kinase–related protein kinase (PIKK) best known for its role in DNA damage response. ATM also functions in oxidative stress response, insulin signaling, and neurogenesis. Our electron cryomicroscopy (cryo-EM) suggests that human ATM is in a dynamic equilibrium between closed and open dimers. In the closed state, the PIKK regulatory domain blocks the peptide substrate–binding site, suggesting that this conformation may represent an inactive or basally active enzyme. The active site is held in this closed conformation by interaction with a long helical hairpin in the TRD3 (tetratricopeptide repeats domain 3) domain of the symmetry-related molecule. The open dimer has two protomers with only a limited contact interface, and it lacks the intermolecular interactions that block the peptide-binding site in the closed dimer. This suggests that the open conformation may be more active. The ATM structure shows the detailed topology of the regulator-interacting N-terminal helical solenoid. The ATM conformational dynamics shown by the structures represent an important step in understanding the enzyme regulation. PMID:28508083

Quality assurance of laboratory work and clinical use of laboratory tests in general practice in norway: a survey.

PubMed

Thue, Geir; Jevnaker, Marianne; Gulstad, Guri Andersen; Sandberg, Sverre

2011-09-01

Virtually all the general practices in Norway participate in the Norwegian Quality Improvement of Laboratory Services in Primary Care, NOKLUS. In order to assess and develop NOKLUS's services, it was decided to carry out an investigation in the largest participating group, general practices. In autumn 2008 a questionnaire was sent to all Norwegian general practices asking for feedback on different aspects of NOKLUS's main services: contact with medical laboratory technologists, sending of control materials, use and maintenance of practice-specific laboratory binders, courses, and testing of laboratory equipment. In addition, attitudes were elicited towards possible new services directed at assessing other technical equipment and clinical use of tests. Responses were received from 1290 of 1552 practices (83%). The great majority thought that the frequency of sending out control material should continue as at present, and they were pleased with the feedback reports and follow-up by the laboratory technologists in the counties. Even after many years of practical experience, there is still a need to update laboratory knowledge through visits to practices, courses, and written information. Practices also wanted quality assurance of blood pressure meters and spirometers, and many doctors wanted feedback on their use of laboratory tests. Services regarding quality assurance of point-of-care tests, guidance, and courses should be continued. Quality assurance of other technical equipment and of the doctor's clinical use of laboratory tests should be established as part of comprehensive quality assurance.

g_contacts: Fast contact search in bio-molecular ensemble data

NASA Astrophysics Data System (ADS)

Blau, Christian; Grubmuller, Helmut

2013-12-01

Short-range interatomic interactions govern many bio-molecular processes. Therefore, identifying close interaction partners in ensemble data is an essential task in structural biology and computational biophysics. A contact search can be cast as a typical range search problem for which efficient algorithms have been developed. However, none of those has yet been adapted to the context of macromolecular ensembles, particularly in a molecular dynamics (MD) framework. Here a set-decomposition algorithm is implemented which detects all contacting atoms or residues in maximum O(Nlog(N)) run-time, in contrast to the O(N2) complexity of a brute-force approach. Catalogue identifier: AEQA_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEQA_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 8945 No. of bytes in distributed program, including test data, etc.: 981604 Distribution format: tar.gz Programming language: C99. Computer: PC. Operating system: Linux. RAM: ≈Size of input frame Classification: 3, 4.14. External routines: Gromacs 4.6[1] Nature of problem: Finding atoms or residues that are closer to one another than a given cut-off. Solution method: Excluding distant atoms from distance calculations by decomposing the given set of atoms into disjoint subsets. Running time:≤O(Nlog(N)) References: [1] S. Pronk, S. Pall, R. Schulz, P. Larsson, P. Bjelkmar, R. Apostolov, M. R. Shirts, J.C. Smith, P. M. Kasson, D. van der Spoel, B. Hess and Erik Lindahl, Gromacs 4.5: a high-throughput and highly parallel open source molecular simulation toolkit, Bioinformatics 29 (7) (2013).

[Two Crimean-Congo hemorrhagic fever cases without history of tick contact from Ankara region].

PubMed

Kaya Kiliç, Esra; Yilmaz, Umut; Cesur, Salih; Koçak Tufan, Zeliha; Kurtoğlu, Yasemin; Bulut, Cemal; Kinikli, Sami; Irmak, Hasan; Demiröz, Ali Pekcan

2009-10-01

Crimean-Congo hemorrhagic fever (CCHF) is a tick-borne viral disease presenting with flu-like symptoms, fever, hemorrhage and petechia. The virus (CCHFV) is a member of the Nairovirus genera of Bunyaviridae family and can be transmitted to humans by Hyalomma tick-bite, by exposure to infected blood and fomites of patient with CCHF or contact with animal tissue in viremic phase. In this study we present two cases with CCHF but without history of tick bite or exposure to infected fomites, even not coming from endemic areas. The first case was a 67 years old male patient presented with fever, fatique and shortness of breath. Physical examination revealed rales in right lower segments of lung. Laboratory findings showed elevation of liver enzymes with thrombocytopenia and prolonged prothrombin time. Serological markers for viral hepatitis, cytomegalovirus (CMV) and Epstein-Barr virus (EBV) were negative. The patient was found to be IgM and RNA positive for CCHFV by ELISA and polymerase chain reaction (PCR) methods, respectively. His history indicated a contact with livestock. The second patient was a 60 years old male dealing with husbandry. He had fever, fatique and myalgia. Physical examination revealed petechial rash on legs. Laboratory findings showed elevated liver enzymes, prolonged phrothrombin time and thrombocytopenia. Viral hepatitis markers, CMV-IgM and EBV-IgM were found negative. He was also found to be IgM and RNA positive for CCHFV in the reference laboratory. In conclusion, CCHF should be considered in the differential diagnosis of patients who contact with livestock and present with fever, fatigue, rash, elevated liver enzymes, thrombocytopenia and prolonged prothrombin time eventhough they do not reside in endemic areas for CCHF.

Diversity and antimicrobial susceptibility profiling of staphylococci isolated from bovine mastitis cases and close human contacts.

PubMed

Schmidt, T; Kock, M M; Ehlers, M M

2015-09-01

The objectives of this study were to examine the diversity of Staphylococcus spp. recovered from bovine intramammary infections and humans working in close contact with the animals and to evaluate the susceptibility of the staphylococcal isolates to different antimicrobials. A total of 3,387 milk samples and 79 human nasal swabs were collected from 13 sampling sites in the KwaZulu-Natal province of South Africa. In total, 146 Staph. aureus isolates and 102 coagulase-negative staphylococci (CNS) were recovered from clinical and subclinical milk samples. Staphylococcusaureus was isolated from 12 (15.2%) of the human nasal swabs and 95 representative CNS were recovered for further characterization. The CNS were identified using multiplex-PCR assays, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS), and tuf gene sequencing. Seven Staphylococcus spp. were identified among the CNS of bovine origin, with Staph.chromogenes (78.4%) predominating. The predominant CNS species recovered from the human nasal swabs was Staph.epidermidis (80%) followed by Staph.chromogenes (6.3%). The antimicrobial susceptibility of all staphylococcal isolates was evaluated using disk diffusion and was supplemented by screening for specific antimicrobial resistance genes. Ninety-eight (67.1%) Staph.aureus isolates of bovine origin were pansusceptible; 39 (26.7%) isolates were resistant to a single class, and 7 (4.8%) isolates were resistant to 2 classes of antimicrobials. Two Staph. aureus (1.4%) isolates were multidrug-resistant. Resistance to penicillin was common, with 28.8% of the bovine and 75% of the human Staph. aureus isolates exhibiting resistance. A similar observation was made with the CNS, where 37.3% of the bovine and 89.5% of the human isolates were resistant to penicillin. Multidrug-resistance was common among the human CNS, with 39% of the isolates exhibiting resistance to 3 or more classes of antimicrobials. The antimicrobial

Tight contact technique during side-to-side laser tissue soldering of rabbit aortas improves tensile strength.

PubMed

Alfieri, A; Bregy, A; Constantinescu, M; Stuker, F; Schaffner, T; Frenz, M; Banic, A; Reinert, M

2008-01-01

Cerebral revascularization may be indicated either for blood flow preservation or flow augmentation, often in clinical situations where neither endovascular nor standard surgical intervention can be performed. Cerebral revascularization can be performed by using a temporary occlusive or a non-occlusive technique. Both of these possibilities have their specific range of feasibility. Therefore non-occlusive revascularization techniques have been developed. To further reduce the risks for patients, less time consuming, sutureless techniques such as laser tissue soldering are currently being investigated. In the present study, a new technique for side-to-side anastomosis was developed. Using a "sandwich technique", two vessels are kept in close contact during the laser soldering. Thoraco-abdominal aortas from 24 different rabbits were analyzed for laser irradiation induced tensile strength. Two different irradiation modes (continuous and pulsed) were used. The results were compared to conventional, noncontact laser soldering. Histology was performed using HE, Mason's Trichrome staining. The achieved tensile strengths were significantly higher using the close contact "sandwich technique" as compared to the conventional adaptation technique. Furthermore, tensile strength was higher in the continuously irradiated specimen as compared to the specimen undergoing pulsed laser irradiation. The histology showed similar denaturation areas in both groups. The addition of a collagen membrane between vessel components reduced the tensile strength. These first results proved the importance of close and tight contact during the laser soldering procedure thus enabling the development of a "sandwich laser irradiation device" for in vivo application in the rabbit.

78 FR 75927 - National Institute on Alcohol Abuse and Alcoholism; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-13

... Alcohol Abuse and Alcoholism; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute on Alcohol Abuse... Institute on Alcohol Abuse and Alcoholism, 5635 Fishers Lane, (Teleconference), Rockville, MD 20852. Contact...

78 FR 52938 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-27

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical...). Contact Person: John K. Hayes, Ph.D., Scientific Review Officer, National Institute of Biomedical Imaging...

78 FR 76632 - National Institute of Biomedical Imaging and Bioengineering; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-18

... Biomedical Imaging and Bioengineering; Notice of Closed Meeting Pursuant to section 10(d) of the Federal... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute of Biomedical...). Contact Person: John K. Hayes, Ph.D., Scientific Review Officer, National Institute of Biomedical Imaging...

75 FR 10291 - National Institute on Alcohol Abuse and Alcoholism; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-05

... Alcohol Abuse and Alcoholism; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute on Alcohol Abuse.... Contact Person: Lorraine Gunzerath, PhD, MBA, Scientific Review Officer, National Institute on Alcohol...

Development of a laboratory niche Web site.

PubMed

Dimenstein, Izak B; Dimenstein, Simon I

2013-10-01

This technical note presents the development of a methodological laboratory niche Web site. The "Grossing Technology in Surgical Pathology" (www.grossing-technology.com) Web site is used as an example. Although common steps in creation of most Web sites are followed, there are particular requirements for structuring the template's menu on methodological laboratory Web sites. The "nested doll principle," in which one object is placed inside another, most adequately describes the methodological approach to laboratory Web site design. Fragmentation in presenting the Web site's material highlights the discrete parts of the laboratory procedure. An optimally minimal triad of components can be recommended for the creation of a laboratory niche Web site: a main set of media, a blog, and an ancillary component (host, contact, and links). The inclusion of a blog makes the Web site a dynamic forum for professional communication. By forming links and portals, cloud computing opens opportunities for connecting a niche Web site with other Web sites and professional organizations. As an additional source of information exchange, methodological laboratory niche Web sites are destined to parallel both traditional and new forms, such as books, journals, seminars, webinars, and internal educational materials. Copyright © 2013 Elsevier Inc. All rights reserved.

A 3D contact analysis approach for the visualization of the electrical contact asperities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roussos, Constantinos C.; Swingler, Jonathan

The electrical contact is an important phenomenon that should be given into consideration to achieve better performance and long term reliability for the design of devices. Based upon this importance, the electrical contact interface has been visualized as a “3D Contact Map” and used in order to investigate the contact asperities. The contact asperities describe the structures above and below the contact spots (the contact spots define the 3D contact map) to the two conductors which make the contact system. The contact asperities require the discretization of the 3D microstructures of the contact system into voxels. A contact analysis approachmore » has been developed and introduced in this paper which shows the way to the 3D visualization of the contact asperities of a given contact system. For the discretization of 3D microstructure of contact system into voxels, X-ray Computed Tomography (CT) method is used in order to collect the data of a 250 V, 16 A rated AC single pole rocker switch which is used as a contact system for investigation.« less

A 3D contact analysis approach for the visualization of the electrical contact asperities

PubMed Central

Swingler, Jonathan

2017-01-01

The electrical contact is an important phenomenon that should be given into consideration to achieve better performance and long term reliability for the design of devices. Based upon this importance, the electrical contact interface has been visualized as a ‘‘3D Contact Map’’ and used in order to investigate the contact asperities. The contact asperities describe the structures above and below the contact spots (the contact spots define the 3D contact map) to the two conductors which make the contact system. The contact asperities require the discretization of the 3D microstructures of the contact system into voxels. A contact analysis approach has been developed and introduced in this paper which shows the way to the 3D visualization of the contact asperities of a given contact system. For the discretization of 3D microstructure of contact system into voxels, X-ray Computed Tomography (CT) method is used in order to collect the data of a 250 V, 16 A rated AC single pole rocker switch which is used as a contact system for investigation. PMID:28105383

A 3D contact analysis approach for the visualization of the electrical contact asperities

DOE PAGES

Roussos, Constantinos C.; Swingler, Jonathan

2017-01-11

The electrical contact is an important phenomenon that should be given into consideration to achieve better performance and long term reliability for the design of devices. Based upon this importance, the electrical contact interface has been visualized as a “3D Contact Map” and used in order to investigate the contact asperities. The contact asperities describe the structures above and below the contact spots (the contact spots define the 3D contact map) to the two conductors which make the contact system. The contact asperities require the discretization of the 3D microstructures of the contact system into voxels. A contact analysis approachmore » has been developed and introduced in this paper which shows the way to the 3D visualization of the contact asperities of a given contact system. For the discretization of 3D microstructure of contact system into voxels, X-ray Computed Tomography (CT) method is used in order to collect the data of a 250 V, 16 A rated AC single pole rocker switch which is used as a contact system for investigation.« less

Fault healing promotes high-frequency earthquakes in laboratory experiments and on natural faults

USGS Publications Warehouse

McLaskey, Gregory C.; Thomas, Amanda M.; Glaser, Steven D.; Nadeau, Robert M.

2012-01-01

Faults strengthen or heal with time in stationary contact and this healing may be an essential ingredient for the generation of earthquakes. In the laboratory, healing is thought to be the result of thermally activated mechanisms that weld together micrometre-sized asperity contacts on the fault surface, but the relationship between laboratory measures of fault healing and the seismically observable properties of earthquakes is at present not well defined. Here we report on laboratory experiments and seismological observations that show how the spectral properties of earthquakes vary as a function of fault healing time. In the laboratory, we find that increased healing causes a disproportionately large amount of high-frequency seismic radiation to be produced during fault rupture. We observe a similar connection between earthquake spectra and recurrence time for repeating earthquake sequences on natural faults. Healing rates depend on pressure, temperature and mineralogy, so the connection between seismicity and healing may help to explain recent observations of large megathrust earthquakes which indicate that energetic, high-frequency seismic radiation originates from locations that are distinct from the geodetically inferred locations of large-amplitude fault slip

Contact Lens Risks

MedlinePlus

... Health and Consumer Devices Consumer Products Contact Lenses Contact Lens Risks Share Tweet Linkedin Pin it More ... redness blurred vision swelling pain Serious Hazards of Contact Lenses Symptoms of eye irritation can indicate a ...

Gamete donors' expectations and experiences of contact with their donor offspring

PubMed Central

Kirkman, Maggie; Bourne, Kate; Fisher, Jane; Johnson, Louise; Hammarberg, Karin

2014-01-01

STUDY QUESTION What are the expectations and experiences of anonymous gamete donors about contact with their donor offspring? SUMMARY ANSWER Rather than consistently wanting to remain distant from their donor offspring, donors' expectations and experiences of contact with donor offspring ranged from none to a close personal relationship. WHAT IS KNOWN ALREADY Donor conception is part of assisted reproduction in many countries, but little is known about its continuing influence on gamete donors' lives. STUDY DESIGN, SIZE, DURATION A qualitative research model appropriate for understanding participants' views was employed; semi-structured interviews were conducted during January–March 2013. PARTICIPANTS/MATERIALS, SETTING, METHODS Before 1998, gamete donors in Victoria, Australia, were subject to evolving legislation that allowed them to remain anonymous or (from 1988) to consent to the release of identifying information. An opportunity to increase knowledge of donors' expectations and experiences of contact with their donor offspring recently arose in Victoria when a recommendation was made to introduce mandatory identification of donors on request from their donor offspring, with retrospective effect. Pre-1998 donors were invited through an advertising campaign to be interviewed about their views, experiences and expectations; 36 sperm donors and 6 egg donors participated. MAIN RESULTS AND THE ROLE OF CHANCE This research is unusual in achieving participation by donors who would not normally identify themselves to researchers or government inquiries. Qualitative thematic analysis revealed that most donors did not characterize themselves as parents of their donor offspring. Donors' expectations and experiences of contact with donor offspring ranged from none to a close personal relationship. LIMITATIONS, REASONS FOR CAUTION It is not possible to establish whether participants were representative of all pre-1998 donors. WIDER IMPLICATIONS OF THE FINDINGS Anonymous

Friction and universal contact area law for randomly rough viscoelastic contacts.

PubMed

Scaraggi, M; Persson, B N J

2015-03-18

We present accurate numerical results for the friction force and the contact area for a viscoelastic solid (rubber) in sliding contact with hard, randomly rough substrates. The rough surfaces are self-affine fractal with roughness over several decades in length scales. We calculate the contribution to the friction from the pulsating deformations induced by the substrate asperities. We also calculate how the area of real contact, A(v, p), depends on the sliding speed v and on the nominal contact pressure p, and we show how the contact area for any sliding speed can be obtained from a universal master curve A(p). The numerical results are found to be in good agreement with the predictions of an analytical contact mechanics theory.

Contact Lens Care

MedlinePlus

... your prescription expires Lens measurements The contact lens brand name and material Your doctor’s name and contact ... mail-order sellers may send you a different brand. Contact lenses may look the same, but materials ...

First contact diagnosis and management of contact lens-related complications.

PubMed

Fagan, Xavier J; Jhanji, Vishal; Constantinou, Marios; Amirul Islam, F M; Taylor, Hugh R; Vajpayee, Rasik B

2012-08-01

To describe the spectrum of contact lens-related problems in cases presenting to a tertiary referral eye hospital. A retrospective case record analysis of 111 eyes of 97 consecutive patients was undertaken over a period of five months at the Royal Victorian Eye and Ear Hospital, Melbourne, Australia. Contact lens-related complications (CLRC) were classified into microbial keratitis, sterile corneal infiltrates, corneal epitheliopathy and contact lens-related red eye (CLARE). Main parameters examined were nature of the first contact, clinical diagnosis, and management pattern. Forty-two percent of the initial presentations were to health care practitioners (HCPs) other than ophthalmologists. Mean duration from the onset of symptoms to presentation was 6.3 ± 10.9 days. Forty-nine percent (n = 54) of patients had an associated risk factor, most commonly overnight use of contact lenses (n = 14, 13 %). Most common diagnosis at presentation was corneal epitheliopathy (68 %) followed by sterile infiltrates (10 %), CLARE (8 %) and microbial keratitis (6 %). No significant differences were found in the pattern of treatment modalities administered by ophthalmologists and other HCPs. HCPs other than ophthalmologists are the first contact for contact lens-related problems in a significant proportion of patients. These HCPs manage the majority of CLRC by direct treatment or immediate referral.

Physician-applied contact pressure and table force response during unilateral thoracic manipulation.

PubMed

Kirstukas, S J; Backman, J A

1999-06-01

To measure the applied loading to human subjects during the reinforced unilateral thoracic manipulation. Biomechanical descriptive study. The National College of Chiropractic Clinical Biomechanical Laboratory in Lombard, Illinois. Seven men, ages 24 to 47, with no positive responses regarding muscle relaxants or thoracic spinal fractures, surgeries, or pain. We measured the contact pressure distribution at the physician-subject contact region and extracted three biomechanical parameters. From the measured time-dependent support force magnitudes, we extracted five additional biomechanical parameters. In the application of the reinforced unilateral manipulative treatment, the physician establishes contact and applies a near-static preload force of 250 to 350 N. The dynamic portion of the typical thrust is preceded by a 22% decrease in force magnitude, and the peak thrust magnitude is linearly related to the preload force magnitude. We estimate that the peak contact pressure beneath the chiropractor's pisiform can exceed 1000 kPa, with the highest pressures transmitted over areas as small as 3.6 cm2, depending on manipulative style. This work represents the first attempt at performing simultaneous measurements of the physician-applied loading and table force response and measuring the contact pressure distribution at the physician-patient contact region during chiropractic manipulation. This type of work will lead to a better understanding of the relationship between the dynamic physician-applied normal forces and the resulting load response at the table and gives us additional outcome parameters to quantify manipulative technique.

78 FR 75929 - National Institute on Alcohol Abuse and Alcoholism; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-13

... Alcohol Abuse and Alcoholism; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute on Alcohol Abuse... Alcohol Abuse and Alcoholism, 5635 Fishers Lane, T508, Rockville, MD 20852. Contact Person: Beata Buzas...

77 FR 22794 - National Institute on Alcohol Abuse and Alcoholism; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... Alcohol Abuse and Alcoholism; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute on Alcohol Abuse.... Contact Person: Katrina L Foster, Ph.D., Scientific Review Officer, National Institute on Alcohol Abuse...

76 FR 44599 - National Institute on Alcohol Abuse and Alcoholism; Notice of Closed Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-26

... Alcohol Abuse and Alcoholism; Notice of Closed Meeting Pursuant to section 10(d) of the Federal Advisory... clearly unwarranted invasion of personal privacy. Name of Committee: National Institute on Alcohol Abuse.... Contact Person: Katrina L. Foster, PhD, Scientific Review officer, National Institute on Alcohol Abuse...

Tribological study on rapeseed oil with nano-additives in close contact sliding situation

NASA Astrophysics Data System (ADS)

Gupta, Rajeev Nayan; Harsha, A. P.; Singh, Sagar

2018-02-01

The present work deals with the tribological evaluation of three types of nano-additives, i.e., copper oxide (CuO; ≈ 151.2 nm), cerium oxide (CeO2; ≈ 80 nm) and polytetrafluoroethylene (PTFE; ≈ 90.4 nm) with rapeseed oil under steel-steel sliding contacts. The nano-additives concentrations in the base oil were 0.1, 0.25 and 0.5% w/v for the lubricant formulation. Further, the rapeseed oil was also epoxidized by a chemical method and the tribological behavior was compared with the base oil (unmodified oil) at similar nano-additives concentrations. The ASTM standards were followed for the study of wear preventive and extreme-pressure analysis of nanolubricants, and it was carried out using four-ball tester. In the antiwear test, CeO2 and PTFE nano-additives have shown the significant reduction in the wear scar diameter at the concentration of 0.1% w/v. In the extreme-pressure test, 0.5% w/v concentration was optimum for oxide nanoparticles; however, PTFE nanoparticles did not show positive effect with both the base oils. Different characterization techniques were employed to confirm the oil modification and for the study of the worn surfaces.

A review of micro-contact physics for microelectromechanical systems (MEMS) metal contact switches

NASA Astrophysics Data System (ADS)

Toler, Benjamin F.; Coutu, Ronald A., Jr.; McBride, John W.

2013-10-01

Innovations in relevant micro-contact areas are highlighted, these include, design, contact resistance modeling, contact materials, performance and reliability. For each area the basic theory and relevant innovations are explored. A brief comparison of actuation methods is provided to show why electrostatic actuation is most commonly used by radio frequency microelectromechanical systems designers. An examination of the important characteristics of the contact interface such as modeling and material choice is discussed. Micro-contact resistance models based on plastic, elastic-plastic and elastic deformations are reviewed. Much of the modeling for metal contact micro-switches centers around contact area and surface roughness. Surface roughness and its effect on contact area is stressed when considering micro-contact resistance modeling. Finite element models and various approaches for describing surface roughness are compared. Different contact materials to include gold, gold alloys, carbon nanotubes, composite gold-carbon nanotubes, ruthenium, ruthenium oxide, as well as tungsten have been shown to enhance contact performance and reliability with distinct trade offs for each. Finally, a review of physical and electrical failure modes witnessed by researchers are detailed and examined.

Raman spectral characteristics of magmatic-contact metamorphic coals from Huainan Coalfield, China

NASA Astrophysics Data System (ADS)

Chen, Shancheng; Wu, Dun; Liu, Guijian; Sun, Ruoyu

2017-01-01

Normal burial metamorphism of coal superimposed by magmatic-contact metamorphism makes the characteristics of the Raman spectrum of coal changed. Nine coal samples were chosen at a coal transect perpendicular to the intrusive dike, at the No. 3 coal seam, Zhuji Coal Mine, Huainan Coalfield, China, with different distances from dike-coal boundary (DCB). Geochemical (proximate and ultimate) analysis and mean random vitrinite reflectance (R0, %) indicate that there is a significant relationship between the values of volatile matter and R0 in metamorphosed coals. Raman spectra show that the graphite band (G band) becomes the major band but the disordered band (D band) disappears progressively, with the increase of metamorphic temperature in coals, showing that the structural organization in high-rank contact-metamorphosed coals is close to that of well-crystallized graphite. Evident relationships are observed between the calculated Raman spectral parameters and the peak metamorphic temperature, suggesting some spectral parameters have the potentials to be used as geothermometers for contact-metamorphic coals.

Low frequency electrical noise across contacts between a normal conductor and superconducting bulk YBa2Cu3O7

NASA Technical Reports Server (NTRS)

Hall, J.; Chen, T. M.

1991-01-01

Virtually every device that makes use of the new ceramic superconductors will need normal conductor to superconductor contacts. The current-voltage and electrical noise characteristics of these contacts could become important design considerations. I-V and low frequency electrical noise measurements are presented on contacts between a normal conductor and superconducting polycrystalline YBa2Cu3O7. The contacts were formed by first sputtering gold palladium pads onto the surface of the bulk superconductor and then using silver epoxy to attach a wire(s) to each pad. Voltage across the contacts was found for small current densities. The voltage spectral density, S sub v(f), a quantity often used to characterize electrical noise, very closely followed an empirical relationship given by S sub v(f) = C(VR)sq/f, where V is the DC voltage across the contact, R is the contact resistance, F is frequency, and C is a contant found to be 2 x 10(exp -10)/Omega sq at 78 K. This relationship was found to be independent of contact area, contact geometry, sample fabrication technique, and sample density.

Comparative Biomechanical Study on Contact Alterations After Lateral Meniscus Posterior Root Avulsion, Transosseous Reinsertion, and Total Meniscectomy.

PubMed

Perez-Blanca, Ana; Espejo-Baena, Alejandro; Amat Trujillo, Daniel; Prado Nóvoa, María; Espejo-Reina, Alejandro; Quintero López, Clara; Ezquerro Juanco, Francisco

2016-04-01

To compare the effects of lateral meniscus posterior root avulsion left in situ, its repair, and meniscectomy on contact pressure distribution in both tibiofemoral compartments at different flexion angles. Eight cadaveric knees were tested under compressive 1000 N load for 4 lateral meniscus conditions (intact, posterior root avulsion, transosseous root repair, and total meniscectomy) at flexion angles 0°, 30°, 60°, and 90°. Contact area and pressure distribution were registered using K-scan pressure sensors inserted between menisci and tibial plateau. In the lateral compartment, root detachment decreased contact area (P = .017, 0° and 30°; P = .012, 60° and 90°) and increased mean (P = .012, all angles) and maximum (P = .025, 0° and 30°; P = .017, 60°; P = .012, 90°) pressures relative to intact condition. Repair restored all measured parameters close to intact at 0°, but effectiveness decreased with flexion angle, yielding no significant effect at 90°. Meniscectomy produced higher decreases than root avulsion in contact area (P = .012, 0° and 90°; P = .05, 30° and 60°) and increases in mean (P = .017, 0° and 30°; P = .018, 90°) and maximum pressure (P = .012, 0°; P = .036, 30°). In the medial compartment, lesion changed the contact area at high flexion angles only, while meniscectomy induced greater changes at all angles. Lateral meniscus posterior root avulsion generates significant alterations in contact area and pressures at lateral knee compartment for flexion angles between full extension and 90°. Meniscectomy causes greater disorders than the avulsion left in situ. Transosseous repair with a single suture restores these alterations to conditions close to intact at 0° and 30° but not at 60° and 90°. Altered contact mechanics after lateral meniscus posterior root avulsion might have degenerative consequences. Transosseous repair with one suture should be revised to effectively restore contact mechanics at high flexion angles

Geysers advanced direct contact condenser research

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henderson, J.; Bahning, T.; Bharathan, D.

1997-12-31

The first geothermal application of the Advanced Direct Contact Condenser (ADCC) technology developed by the National Renewable Energy Laboratory (NREL) is now operational and is being tested at The Geysers Power Plant Unit 11. This major research effort is being supported through the combined efforts of NREL, The Department of Energy (DOE), and Pacific Gas and Electric (PG&E). NREL and PG&E have entered into a Cooperative Research And Development Agreement (CRADA) for a project to improve the direct-contact condenser performance at The Geysers Power Plant. This project is the first geothermal adaptation of an advanced condenser design developed for themore » Ocean Thermal Energy Conversion (OTEC) systems. PG&E expects this technology to improve power plant performance and to help extend the life of the steam field by using steam more efficiently. In accordance with the CRADA, no money is transferred between the contracting parties. In this case the Department of Energy is funding NREL for their efforts in this project and PG&E is contributing funds in kind. Successful application of this technology at The Geysers will provide a basis for NREL to continue to develop this technology for other geothermal and fossil power plant systems.« less

Lack of SARS transmission and U.S. SARS case-patient.

PubMed

Peck, Angela J; Newbern, E Claire; Feikin, Daniel R; Issakbaeva, Elmira T; Park, Benjamin J; Fehr, Jason; LaMonte, Ashley C; Le, Thong P; Burger, Terry L; Rhodes, Luther V; Weltman, Andre; Erdman, Dean; Ksiazek, Thomas G; Lingappa, Jairam R

2004-02-01

In early April 2003, severe acute respiratory syndrome (SARS) was diagnosed in a Pennsylvania resident after his exposure to persons with SARS in Toronto, Canada. To identify contacts of the case-patient and evaluate the risk for SARS transmission, a detailed epidemiologic investigation was performed. On the basis of this investigation, 26 persons (17 healthcare workers, 4 household contacts, and 5 others) were identified as having had close contact with this case-patient before infection-control practices were implemented. Laboratory evaluation of clinical specimens showed no evidence of transmission of SARS-associated coronavirus (SARS-CoV) infection to any close contact of this patient. This investigation documents that, under certain circumstances, SARS-CoV is not readily transmitted to close contacts, despite ample unprotected exposures. Improving the understanding of risk factors for transmission will help focus public health control measures.

Comparison of Field and Laboratory-Based Tests for Behavioral Response of Aedes aegypti (Diptera: Culicidae) to Repellents.

PubMed

Sathantriphop, Sunaiyana; Kongmee, Monthathip; Tainchum, Krajana; Suwansirisilp, Kornwika; Sanguanpong, Unchalee; Bangs, Michael J; Chareonviriyaphap, Theeraphap

2015-12-01

The repellent and irritant effects of three essential oils-clove, hairy basil, and sweet basil-were compared using an excito-repellency test system against an insecticide-resistant strain of Aedes aegypti (L.) females from Pu Teuy, Kanchanaburi Province. DEET was used as the comparison standard compound. Tests were conducted under field and controlled laboratory conditions. The most marked repellent effect (spatial noncontact assay) among the three test essential oils was exhibited by sweet basil, Ocimum basilicum L. (53.8% escaped mosquitoes in 30-min exposure period) under laboratory conditions while hairy basil, Ocimum americanum L. and clove, Syzygium aromaticum (L.) Merill et. L.M. Perry from laboratory tests and sweet basil from field tests were the least effective as repellents (0-14%). In contrast, the contact assays measuring combined irritancy (excitation) and repellency effects found the best contact irritant response to hairy basil and DEET in field tests, whereas all others in laboratory and field were relatively ineffective in stimulating mosquitoes to move out the test chambers (0-5.5%). All three essential oils demonstrated significant differences in behavioral responses between field and laboratory conditions, whereas there was no significant difference in contact and noncontact assays for DEET between the two test conditions (P > 0.05). © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Scanning tunneling microscope-quartz crystal microbalance study of temperature gradients at an asperity contact.

PubMed

Pan, L; Krim, J

2013-01-01

Investigations of atomic-scale friction frequently involve setups where a tip and substrate are initially at different temperatures. The temperature of the sliding interface upon contact has thus become a topic of interest. A method for detecting initial tip-sample temperature differences at an asperity contact is described, which consists of a scanning tunneling microscope (STM) tip in contact with the surface electrode of a quartz crystal microbalance (QCM). The technique makes use of the fact that a QCM is extremely sensitive to abrupt changes in temperature. In order to demonstrate the technique's capabilities, QCM frequency shifts were recorded for varying initial tip-substrate temperature differences as an STM tip was brought into and out of contact. The results are interpreted within the context of a recent model for thermal heat conduction at an asperity contact, and it is concluded that the transient frequency response is attributable to small changes in temperature close to the region of contact rather than a change in the overall temperature of the QCM itself. For the assumed model parameters, the results moreover reveal substantial temperature discontinuities at the boundary between the tip and the sample, for example, on the order of 10-15 °C for initial temperature differences of 20 °C.

Scanning tunneling microscope-quartz crystal microbalance study of temperature gradients at an asperity contact

NASA Astrophysics Data System (ADS)

Pan, L.; Krim, J.

2013-01-01

Investigations of atomic-scale friction frequently involve setups where a tip and substrate are initially at different temperatures. The temperature of the sliding interface upon contact has thus become a topic of interest. A method for detecting initial tip-sample temperature differences at an asperity contact is described, which consists of a scanning tunneling microscope (STM) tip in contact with the surface electrode of a quartz crystal microbalance (QCM). The technique makes use of the fact that a QCM is extremely sensitive to abrupt changes in temperature. In order to demonstrate the technique's capabilities, QCM frequency shifts were recorded for varying initial tip-substrate temperature differences as an STM tip was brought into and out of contact. The results are interpreted within the context of a recent model for thermal heat conduction at an asperity contact, and it is concluded that the transient frequency response is attributable to small changes in temperature close to the region of contact rather than a change in the overall temperature of the QCM itself. For the assumed model parameters, the results moreover reveal substantial temperature discontinuities at the boundary between the tip and the sample, for example, on the order of 10-15 °C for initial temperature differences of 20 °C.

ComplexContact: a web server for inter-protein contact prediction using deep learning.

PubMed

Zeng, Hong; Wang, Sheng; Zhou, Tianming; Zhao, Feifeng; Li, Xiufeng; Wu, Qing; Xu, Jinbo

2018-05-22

ComplexContact (http://raptorx2.uchicago.edu/ComplexContact/) is a web server for sequence-based interfacial residue-residue contact prediction of a putative protein complex. Interfacial residue-residue contacts are critical for understanding how proteins form complex and interact at residue level. When receiving a pair of protein sequences, ComplexContact first searches for their sequence homologs and builds two paired multiple sequence alignments (MSA), then it applies co-evolution analysis and a CASP-winning deep learning (DL) method to predict interfacial contacts from paired MSAs and visualizes the prediction as an image. The DL method was originally developed for intra-protein contact prediction and performed the best in CASP12. Our large-scale experimental test further shows that ComplexContact greatly outperforms pure co-evolution methods for inter-protein contact prediction, regardless of the species.

Current knowledge on biomarkers for contact sensitization and allergic contact dermatitis.

PubMed

Koppes, Sjors A; Engebretsen, Kristiane A; Agner, Tove; Angelova-Fischer, Irena; Berents, Teresa; Brandner, Johanna; Brans, Richard; Clausen, Maja-Lisa; Hummler, Edith; Jakasa, Ivone; Jurakić-Tončic, Ružica; John, Swen M; Khnykin, Denis; Molin, Sonja; Holm, Jan O; Suomela, Sari; Thierse, Hermann-Josef; Kezic, Sanja; Martin, Stefan F; Thyssen, Jacob P

2017-07-01

Contact sensitization is common and affects up to 20% of the general population. The clinical manifestation of contact sensitization is allergic contact dermatitis. This is a clinical expression that is sometimes difficult to distinguish from other types of dermatitis, for example irritant and atopic dermatitis. Several studies have examined the pathogenesis and severity of allergic contact dermatitis by measuring the absence or presence of various biomarkers. In this review, we provide a non-systematic overview of biomarkers that have been studied in allergic contact dermatitis. These include genetic variations and mutations, inflammatory mediators, alarmins, proteases, immunoproteomics, lipids, natural moisturizing factors, tight junctions, and antimicrobial peptides. We conclude that, despite the enormous amount of data, convincing specific biomarkers for allergic contact dermatitis are yet to be described. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Comninou contact zones for a crack parallel to an interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph, P.F.; Gadi, K.S.; Erdogen, F.

One of the interesting features in studying the state of stress in elastic solids near singular points, is the so called complex singularity that gives rise to an apparent local oscillatory behavior in the stress and displacement fields. The region in which this occurs is very small, much smaller than any plastic zone would be, and therefore the oscillations can be ignored in practical applications. Nevertheless, it is a matter of interesting theoretical investigation. The Comninou model of a small contact zone near the crack tip appears to correct for this anomaly within the framework of the linear theory. Thismore » model seems to make sense out of a {open_quotes}solution{close_quotes} that violates the boundary conditions. Erdogan and Joseph, showed (to themselves anyway) that the Comninou model actually has a physical basis. They considered a crack parallel to an interface where the order of the singularity is always real. With great care in solving the singular integral equations, it was shown that as the crack approaches the interface, a pinching effect is observed at the crack tip. This pinching effect proves that in the limit as the crack approaches the interface, the correct way to handle the problem is to consider crack surface contact. In this way, the issue of {open_quotes}oscillations{close_quotes} is never encountered for the interface crack problem. In the present study, the value of h/a that corresponds to crack closure (zero value of the stress intensity factor) will be determined for a given material pair for tensile loading. An asymptotic numerical method for the solution of singular integral equations making use of is used to obtain this result. Results for the crack opening displacement near the tip of the crack and the behavior of the stress intensity factor for cracks very close to the interface are presented. Among other interesting issues to be discussed, this solution shows that the semi-infinite crack parallel to an interface is closed.« less

Contact Dermatitis

MedlinePlus

... Us Media contacts Advertising contacts AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2018 American Academy ... prohibited without prior written permission. AAD logo Advertising, marketing and sponsorships Legal notice Copyright © 2017 American Academy ...

[Assessment of the quality of laboratory diagnosis of intestinal parasitic diseases by the laboratories participating in the Federal System of External Quality Assessment of Clinical Laboratory Testing].

PubMed

Malakhov, V N; Dovgalev, A S; Astanina, S Iu; Serdiuk, A P

2014-01-01

In 2010-2013, the quality of microscopic detection of the causative agents ofparasitic diseases in the feces has been assessed by the specialists of the laboratories of the therapeutic-and-prophylactic institutions (TPIs) and Hygiene and Epidemiology Centers, Russian Inspectorate for the Protection of Consumer Rights and Human Welfare, which are participants of the Federal System of External Quality Assessment of Clinical Laboratory Testing. Thirty-two specimens containing 16 species of human helminths and 4 species of enteric protozoa in different combinations were examined. The findings suggest that the quality of microscopic detection of the causative agents of parasitic diseases is low in the laboratories of health care facilities and that the specialists of the laboratories of TPIs and Hygiene and Epidemiology Centers, Russian Inspectorate for the Protection of Consumer Rights and Human Welfare, do not not possess the knowledge and skills necessary to make a laboratory diagnosis of helminths and enteric protozoa. The average detection rates of helminths and protozoa were at a level of 64 and 36%, respectively. The correct results showed that the proportion of helminths and protozoa were 94.5 and 5.5%, respectively. According to the biological and epidemiological classification of helminths, there were higher detection rates for contact group parasites (Enterobius vermicularis and Hymenolepis nana) and geohelminths (Ascaris, Trichuris trichiura, and others). Biohelminths (Opisthorchis, tapeworms, and others) Were detectable slightly worse.

Contact Dermatitis in Pediatrics.

PubMed

Pelletier, Janice L; Perez, Caroline; Jacob, Sharon E

2016-08-01

Contact dermatitis is an umbrella term that describes the skin's reaction to contacted noxious or allergenic substances. The two main categories of contact dermatitis are irritant type and allergic type. This review discusses the signs, symptoms, causes, and complications of contact dermatitis. It addresses the testing, treatment, and prevention of contact dermatitis. Proper management of contact dermatitis includes avoidance measures for susceptible children. Implementation of a nickel directive (regulating the use of nickel in jewelry and other products that come into contact with the skin) could further reduce exposure to the most common allergens in the pediatric population. [Pediatr Ann. 2016;45(8):e287-e292.]. Copyright 2016, SLACK Incorporated.

Contact irritant responses of Aedes aegypti Using sublethal concentration and focal application of pyrethroid chemicals.

PubMed

Manda, Hortance; Shah, Pankhil; Polsomboon, Suppaluck; Chareonviriyaphap, Theeraphap; Castro-Llanos, Fanny; Morrison, Amy; Burrus, Roxanne G; Grieco, John P; Achee, Nicole L

2013-01-01

Previous studies have demonstrated contact irritant and spatial repellent behaviors in Aedes aegypti following exposure to sublethal concentrations of chemicals. These sublethal actions are currently being evaluated in the development of a push-pull strategy for Ae. aegypti control. This study reports on mosquito escape responses after exposure to candidate chemicals for a contact irritant focused push-pull strategy using varying concentrations and focal application. Contact irritancy (escape) behavior, knockdown and 24 hour mortality rates were quantified in populations of female Ae. aegypti under laboratory conditions and validated in the field (Thailand and Peru) using experimental huts. Evaluations were conducted using varying concentrations and treatment surface area coverage (SAC) of three pyrethroid insecticides: alphacypermethrin, lambacyhalothrin and deltamethrin. Under laboratory conditions, exposure of Ae. aegypti to alphacypermethrin using the standard field application rate (FAR) resulted in escape responses at 25% and 50% SAC that were comparable with escape responses at 100% SAC. Significant escape responses were also observed at <100% SAC using ½FAR of all test compounds. In most trials, KD and 24 hour mortality rates were higher in mosquitoes that did not escape than in those that escaped. In Thailand, field validation studies indicated an early time of exit (by four hours) and 40% increase in escape using ½FAR of alphacypermethrin at 75% SAC compared to a matched chemical-free control. In Peru, however, the maximum increase in Ae. aegypti escape from alphacypermethrin-treated huts was 11%. Results presented here suggest a potential role for sublethal and focal application of contact irritant chemicals in an Ae. aegypti push-pull strategy to reduce human-vector contact inside treated homes. However, the impact of an increase in escape response on dengue virus transmission is currently unknown and will depend on rate of biting on human hosts prior

Factors influencing health care workers’ implementation of tuberculosis contact tracing in Kweneng, Botswana

PubMed Central

Tlale, Lebapotswe; Frasso, Rosemary; Kgosiesele, Onalenna; Selemogo, Mpho; Mothei, Quirk; Habte, Dereje; Steenhoff, Andrew

2016-01-01

Introduction TB contact tracing rates remain low in high burden settings and reasons for this are not well known. We describe factors that influence health care workers' (HCW) implementation of TB contact tracing (CT) in a high TB burden district of Botswana. Methods Data were collected using questionnaires and in-depth interviews in 31 of the 52 health facilities in Kweneng East Health District. Responses were summarized using summary statistics and comparisons between HCW groups were done using parametric or non-parametric tests as per normality of the data distribution. Results One hundred and four HCWs completed questionnaires. Factors that influenced HCW TB contact tracing were their knowledge, attitudes and practices as well as personal factors including decreased motivation and lack of commitment. Patient factors included living further away from the clinic, unknown residential address and high rates of migration and mobility. Administrative factors included staff shortages, lack of transport, poor reporting of TB cases and poor medical infrastructure e.g. suboptimal laboratory services. A national HCW strike and a restructuring of the health system emerged as additional factors during in-depth interviews of TB coordinators. Conclusion Multiple factors lead to poor TB contact tracing in this district. Interventions to increase TB contact tracing will be informed by these findings. PMID:27800084

Factors influencing health care workers' implementation of tuberculosis contact tracing in Kweneng, Botswana.

PubMed

Tlale, Lebapotswe; Frasso, Rosemary; Kgosiesele, Onalenna; Selemogo, Mpho; Mothei, Quirk; Habte, Dereje; Steenhoff, Andrew

2016-01-01

TB contact tracing rates remain low in high burden settings and reasons for this are not well known. We describe factors that influence health care workers' (HCW) implementation of TB contact tracing (CT) in a high TB burden district of Botswana. Data were collected using questionnaires and in-depth interviews in 31 of the 52 health facilities in Kweneng East Health District. Responses were summarized using summary statistics and comparisons between HCW groups were done using parametric or non-parametric tests as per normality of the data distribution. One hundred and four HCWs completed questionnaires. Factors that influenced HCW TB contact tracing were their knowledge, attitudes and practices as well as personal factors including decreased motivation and lack of commitment. Patient factors included living further away from the clinic, unknown residential address and high rates of migration and mobility. Administrative factors included staff shortages, lack of transport, poor reporting of TB cases and poor medical infrastructure e.g. suboptimal laboratory services. A national HCW strike and a restructuring of the health system emerged as additional factors during in-depth interviews of TB coordinators. Multiple factors lead to poor TB contact tracing in this district. Interventions to increase TB contact tracing will be informed by these findings.

Parents and nurses balancing parent-infant closeness and separation: a qualitative study of NICU nurses' perceptions.

PubMed

Feeley, Nancy; Genest, Christine; Niela-Vilén, Hannakaisa; Charbonneau, Lyne; Axelin, Anna

2016-08-20

When a newborn requires neonatal intensive care unit (NICU) hospitalization, parent and infant experience an unusual often prolonged separation. This critical care environment poses challenges to parent-infant closeness. Parents desire physical contact and holding and touching are particularly important. Evidence shows that visitation, holding, talking, and skin to skin contact are associated with better outcomes for infants and parents during hospitalization and beyond. Thus, it would be important to understand closeness in this context. The purpose of this study was to explore from nurses' perspective, what do parents and nurses do to promote parent-infant closeness or provoke separation. Qualitative methods were utilized to attain an understanding of closeness and separation. Following ethics approval, purposive sampling was used to recruit nurses with varying experience working different shifts in NICUs in two countries. Nurses were loaned a smartphone over one work shift to record their thoughts and perceptions of events that occurred or experiences they had that they considered to be closeness or separation between parents and their hospitalized infant. Sample size was determined by saturation (18 Canada, 19 Finland). Audio recordings were subjected to inductive thematic analysis. Team meetings were held to discuss emerging codes, refine categories, and confirm these reflected data from both sites. One overarching theme was elaborated. Balancing closeness and separation was the major theme. Both parents and nurses engaged in actions to optimize closeness. They sought closeness by acting autonomously in infant caregiving, assuming decision-making for their infant, seeking information or skills, and establishing a connection in the face of separation. Parents balanced their desire for closeness with other competing demands, such as their own needs. Nurses balanced infant care needs and ability to handle stimulation with the need for closeness with parents

Projecting social contact matrices in 152 countries using contact surveys and demographic data.

PubMed

Prem, Kiesha; Cook, Alex R; Jit, Mark

2017-09-01

Heterogeneities in contact networks have a major effect in determining whether a pathogen can become epidemic or persist at endemic levels. Epidemic models that determine which interventions can successfully prevent an outbreak need to account for social structure and mixing patterns. Contact patterns vary across age and locations (e.g. home, work, and school), and including them as predictors in transmission dynamic models of pathogens that spread socially will improve the models' realism. Data from population-based contact diaries in eight European countries from the POLYMOD study were projected to 144 other countries using a Bayesian hierarchical model that estimated the proclivity of age-and-location-specific contact patterns for the countries, using Markov chain Monte Carlo simulation. Household level data from the Demographic and Health Surveys for nine lower-income countries and socio-demographic factors from several on-line databases for 152 countries were used to quantify similarity of countries to estimate contact patterns in the home, work, school and other locations for countries for which no contact data are available, accounting for demographic structure, household structure where known, and a variety of metrics including workforce participation and school enrolment. Contacts are highly assortative with age across all countries considered, but pronounced regional differences in the age-specific contacts at home were noticeable, with more inter-generational contacts in Asian countries than in other settings. Moreover, there were variations in contact patterns by location, with work-place contacts being least assortative. These variations led to differences in the effect of social distancing measures in an age structured epidemic model. Contacts have an important role in transmission dynamic models that use contact rates to characterize the spread of contact-transmissible diseases. This study provides estimates of mixing patterns for societies for which

Physical Parameters of Components in Close Binary Systems. V

NASA Astrophysics Data System (ADS)

Zola, S.; Kreiner, J. M.; Zakrzewski, B.; Kjurkchieva, D. P.; Marchev, D. V.; Baran, A.; Rucinski, S. M.; Ogloza, W.; Siwak, M.; Koziel, D.; Drozdz, M.; Pokrzywka, B.

2005-12-01

The paper presents combined spectroscopic and photometric orbital solutions for ten close binary systems: CN And, V776 Cas, FU Dra, UV Lyn, BB Peg, V592 Per, OU Ser, EQ Tau, HN UMa and HT Vir. The photometric data consist of new multicolor light curves, while the spectroscopy has been recently obtained within the radial velocity program at the David Dunlap Observatory (DDO). Absolute parameters of the components for these binary systems are derived. Our results confirm that CN And is not a contact system. Its configuration is semi-detached with the secondary component filling its Roche lobe. The configuration of nine other systems is contact. Three systems (V776 Cas, V592 Per and OU Ser) have high (44-77%) and six (FU Dra, UV Lyn, BB Peg, EQ Tau, HN UMa and HT Vir) low or intermediate (8-32%) fill-out factors. The absolute physical parameters are derived.

A high-resolution human contact network for infectious disease transmission

PubMed Central

Salathé, Marcel; Kazandjieva, Maria; Lee, Jung Woo; Levis, Philip; Feldman, Marcus W.; Jones, James H.

2010-01-01

The most frequent infectious diseases in humans—and those with the highest potential for rapid pandemic spread—are usually transmitted via droplets during close proximity interactions (CPIs). Despite the importance of this transmission route, very little is known about the dynamic patterns of CPIs. Using wireless sensor network technology, we obtained high-resolution data of CPIs during a typical day at an American high school, permitting the reconstruction of the social network relevant for infectious disease transmission. At 94% coverage, we collected 762,868 CPIs at a maximal distance of 3 m among 788 individuals. The data revealed a high-density network with typical small-world properties and a relatively homogeneous distribution of both interaction time and interaction partners among subjects. Computer simulations of the spread of an influenza-like disease on the weighted contact graph are in good agreement with absentee data during the most recent influenza season. Analysis of targeted immunization strategies suggested that contact network data are required to design strategies that are significantly more effective than random immunization. Immunization strategies based on contact network data were most effective at high vaccination coverage. PMID:21149721

Synaptic Contacts Enhance Cell-to-Cell Tau Pathology Propagation.

PubMed

Calafate, Sara; Buist, Arjan; Miskiewicz, Katarzyna; Vijayan, Vinoy; Daneels, Guy; de Strooper, Bart; de Wit, Joris; Verstreken, Patrik; Moechars, Diederik

2015-05-26

Accumulation of insoluble Tau protein aggregates and stereotypical propagation of Tau pathology through the brain are common hallmarks of tauopathies, including Alzheimer's disease (AD). Propagation of Tau pathology appears to occur along connected neurons, but whether synaptic contacts between neurons are facilitating propagation has not been demonstrated. Using quantitative in vitro models, we demonstrate that, in parallel to non-synaptic mechanisms, synapses, but not merely the close distance between the cells, enhance the propagation of Tau pathology between acceptor hippocampal neurons and Tau donor cells. Similarly, in an artificial neuronal network using microfluidic devices, synapses and synaptic activity are promoting neuronal Tau pathology propagation in parallel to the non-synaptic mechanisms. Our work indicates that the physical presence of synaptic contacts between neurons facilitate Tau pathology propagation. These findings can have implications for synaptic repair therapies, which may turn out to have adverse effects by promoting propagation of Tau pathology. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

The nuclear contacts and short range correlations in nuclei

NASA Astrophysics Data System (ADS)

Weiss, R.; Cruz-Torres, R.; Barnea, N.; Piasetzky, E.; Hen, O.

2018-05-01

Atomic nuclei are complex strongly interacting systems and their exact theoretical description is a long-standing challenge. An approximate description of nuclei can be achieved by separating its short and long range structure. This separation of scales stands at the heart of the nuclear shell model and effective field theories that describe the long-range structure of the nucleus using a mean-field approximation. We present here an effective description of the complementary short-range structure using contact terms and stylized two-body asymptotic wave functions. The possibility to extract the nuclear contacts from experimental data is presented. Regions in the two-body momentum distribution dominated by high-momentum, close-proximity, nucleon pairs are identified and compared to experimental data. The amount of short-range correlated (SRC) nucleon pairs is determined and compared to measurements. Non-combinatorial isospin symmetry for SRC pairs is identified. The obtained one-body momentum distributions indicate dominance of SRC pairs above the nuclear Fermi-momentum.

Modeling Thermal Contact Resistance

NASA Technical Reports Server (NTRS)

Kittel, Peter; Sperans, Joel (Technical Monitor)

1994-01-01

One difficulty in using cryocoolers is making good thermal contact between the cooler and the instrument being cooled. The connection is often made through a bolted joint. The temperature drop associated with this joint has been the subject of many experimental and theoretical studies. The low temperature behavior of dry joints have shown some anomalous dependence on the surface condition of the mating parts. There is also some doubts on how well one can extrapolate from the test samples to predicting the performance of a real system. Both finite element and analytic models of a simple contact system have been developed. The model assumes (a) the contact is dry (contact limited to a small portion of the total available area and the spaces in-between the actual contact patches are perfect insulators), (b) contacts are clean (conductivity of the actual contact is the same as the bulk), (c) small temperature gradients (the bulk conductance may be assumed to be temperature independent), (d) the absolute temperature is low (thermal radiation effects are ignored), and (e) the dimensions of the nominal contact area are small compared to the thickness of the bulk material (the contact effects are localized near the contact). The models show that in the limit of actual contact area much less than the nominal area (a much less than A), that the excess temperature drop due to a single point of contact scales as a(exp -1/2). This disturbance only extends a distance approx. A(exp 1/2) into the bulk material. A group of identical contacts will result in an excess temperature drop that scales as n(exp -1/2), where n is the number of contacts and n dot a is constant. This implies that flat rough surfaces will have a lower excess temperature drop than flat polished surfaces.

Noneczematous Contact Dermatitis

PubMed Central

Foti, Caterina; Vestita, Michelangelo; Angelini, Gianni

2013-01-01

Irritant or allergic contact dermatitis usually presents as an eczematous process, clinically characterized by erythematoedematovesicous lesions with intense itching in the acute phase. Such manifestations become erythematous-scaly as the condition progresses to the subacute phase and papular-hyperkeratotic in the chronic phase. Not infrequently, however, contact dermatitis presents with noneczematous features. The reasons underlying this clinical polymorphism lie in the different noxae and contact modalities, as well as in the individual susceptibility and the various targeted cutaneous structures. The most represented forms of non-eczematous contact dermatitis include the erythema multiforme-like, the purpuric, the lichenoid, and the pigmented kinds. These clinical entities must obviously be discerned from the corresponding “pure” dermatitis, which are not associated with contact with exogenous agents. PMID:24109520

Increased resistance of hygroscopic condenser humidifiers when using a closed circuit suction system.

PubMed

Martinez, F J; Pietchel, S; Wise, C; Walek, J; Beamis, J F

1994-10-01

To examine a hygroscopic condenser after clinical use and to describe the interaction of a hygroscopic condenser and a closed circuit suction system used simultaneously. Prospective evaluation of hygroscopic condensers used clinically, and laboratory investigation of a hygroscopic condenser used with a closed circuit suction system. Tertiary referral centers. The hygroscopic condenser used during mechanical ventilation was removed and peak inflation pressure was measured by delivering a standard tidal volume and inspiratory flow across the isolated hygroscopic condenser while recording the peak inflation pressure. In the laboratory, four 10-mL aliquots of saline were instilled via closed circuit suction system into a test lung with fresh hygroscopic condensers (n = 15) inline. At baseline and after each instillation, the hygroscopic condenser was weighed and the peak inflation pressure was measured while in five condensers, peak expiratory flow rate was also measured. In these five devices, hygroscopic condenser resistance was measured with 100 L/min of constant gas flow while measuring the pressure drop across the hygroscopic condenser. In 11 hygroscopic condensers used for 27.5 +/- 11.9 hrs with no closed circuit suction system, the peak inflation pressure was 3.74 +/- 0.58 cm H2O. In the laboratory, instillation of saline via closed circuit suction system was associated with an increase in hygroscopic condenser weight. Peak inflation pressure increased in a quadratic fashion with the increase in hygroscopic condenser weight, while peak expiratory flow rate decreased in a linear fashion. After four saline instillations, hygroscopic condenser resistance increased from 5.66 +/- 0.31 to 13.9 +/- 2.42 cm H2O/L/sec. Clinical use of a hygroscopic condenser alone is not associated with a significant increase in peak inflation pressure. We caution the use of a hygroscopic condenser and a closed circuit suction system simultaneously, as an increase in hygroscopic

77 FR 8887 - National Institute on Deafness and Other Communication Disorders Notice of Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

... Deafness and Other Communication Disorders Notice of Closed Meetings Pursuant to section 10(d) of the... Institute on Deafness and Other Communication Disorders Special Emphasis Panel; Outcome of Cochlear Implants... Call). Contact Person: Shiguang Yang, DVM, Ph.D., Scientific Review Officer, Division of Extramural...

76 FR 11314 - Art Advisory Panel-Notice of Availability of Report of 2010 Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-01

... DEPARTMENT OF THE TREASURY Internal Revenue Service Art Advisory Panel--Notice of Availability of..., the Government in the Sunshine Act, a report summarizing the closed meeting activities of the Art... at http://www.irs.gov . FOR FURTHER INFORMATION CONTACT: Joseph Bothwell, AP:TPV:ART, Internal...

76 FR 11314 - Art Advisory Panel-Notice of Availability of Report of 2009 Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-01

... DEPARTMENT OF THE TREASURY Internal Revenue Service Art Advisory Panel--Notice of Availability of..., the Government in the Sunshine Act, a report summarizing the closed meeting activities of the Art... at http://www.irs.gov . FOR FURTHER INFORMATION CONTACT: Joseph Bothwell, AP:TPV:ART, Internal...

Occupational skin diseases in dental laboratory technicians. (I). Clinical picture and causative factors.

PubMed

Rustemeyer, T; Frosch, P J

1996-02-01

In Germany, occupational skin disease (OSD) in dental technicians (DT) has been steadily rising in recent years and causing considerable costs for medical care and rehabilitation. Our objective in this study was to: (i) examine affected workers; (ii) perform patch tests to identify causative agents; (iii) develop strategies of prevention. 7 dental laboratories were inspected as to materials used, working habits, safety regulations, etc. A computer data base was developed for products (trade name, active ingredient, additives, etc.). A questionnaire regarding development of OSD was sent out to 1132 dental technicians (45 questions). 55 DT with suspected OSD were examined and patch tested with the standard series, an extensive series of methacrylates, and own materials. Working conditions, and knowledge of potential hazards, varied greatly in the laboratories visited. The safety data sheets of working materials were of little use and required supplementation by the computer data base, which provided rapid access to allergological information (e.g., type of acrylate, concentration). In the questionnaire (173 answers), 36% reported skin lesions attributed to work and 1/3 suspected plastic materials as their primary cause. Among the 55 DT examined, allergic contact dermatitis was diagnosed in 63.6% and irritant contact dermatitis in 23.6%. Most of the allergens identified (74%) were found in plastic materials (methyl methacrylate (MMA), 9 patients (16%); 2-hydroxyethyl methacrylate (2-HEMA), 18 patients (33%); ethyleneglycol dimethacrylate (EGDMA), 15 patients (27%)). In 16 patients, multiple sensitizations to various methacrylates were found. The fingertips were primarily involved in allergic contact dermatitis (93%), whereas in irritant contact dermatitis, the dorsa of the fingers (especially of the dominant hand) were affected (80%). 9 patients also showed lesions on the face, neck and forearms. The main irritant factors included wet work, contact with plaster

DC servomechanism parameter identification: a Closed Loop Input Error approach.

PubMed

Garrido, Ruben; Miranda, Roger

2012-01-01

This paper presents a Closed Loop Input Error (CLIE) approach for on-line parametric estimation of a continuous-time model of a DC servomechanism functioning in closed loop. A standard Proportional Derivative (PD) position controller stabilizes the loop without requiring knowledge on the servomechanism parameters. The analysis of the identification algorithm takes into account the control law employed for closing the loop. The model contains four parameters that depend on the servo inertia, viscous, and Coulomb friction as well as on a constant disturbance. Lyapunov stability theory permits assessing boundedness of the signals associated to the identification algorithm. Experiments on a laboratory prototype allows evaluating the performance of the approach. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Evaluation of the electrical contact area in contact-mode scanning probe microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Celano, Umberto, E-mail: celano@imec.be, E-mail: u.celano@gmail.com; Chintala, Ravi Chandra; Vandervorst, Wilfried

The tunneling current through an atomic force microscopy (AFM) tip is used to evaluate the effective electrical contact area, which exists between tip and sample in contact-AFM electrical measurements. A simple procedure for the evaluation of the effective electrical contact area is described using conductive atomic force microscopy (C-AFM) in combination with a thin dielectric. We characterize the electrical contact area for coated metal and doped-diamond tips operated at low force (<200 nN) in contact mode. In both cases, we observe that only a small fraction (<10 nm{sup 2}) of the physical contact (∼100 nm{sup 2}) is effectively contributing to the transportmore » phenomena. Assuming this reduced area is confined to the central area of the physical contact, these results explain the sub-10 nm electrical resolution observed in C-AFM measurements.« less

Optimization of protease-inhibitor interactions by randomizing adventitious contacts

PubMed Central

Komiyama, Tomoko; VanderLugt, Bryan; Fugère, Martin; Day, Robert; Kaufman, Randal J.; Fuller, Robert S.

2003-01-01

Polypeptide protease inhibitors are often found to inhibit targets with which they did not coevolve, as in the case of high-affinity inhibition of bacterial subtilisin by the leech inhibitor eglin c. Two kinds of contacts exist in such complexes: (i) reactive site loop-active site contacts and (ii) interactions outside of these that form the broader enzyme-inhibitor interface. We hypothesized that the second class of “adventitious” contacts could be optimized to generate significant increases in affinity for a target enzyme or discrimination of an inhibitor for closely related target proteases. We began with a modified eglin c, Arg-42–Arg-45–eglin, in which the reactive site loop had been optimized for subtilisin-related processing proteases of the Kex2/furin family. We randomized 10 potential adventitious contact residues and screened for inhibition of soluble human furin. Substitutions at one of these sites, Y49, were also screened against yeast Kex2 and human PC7. These screens identified not only variants that exhibited increased affinity (up to 20-fold), but also species that exhibited enhanced selectivity, that is, increased discrimination between the target enzymes (up to 41-fold for furin versus PC7 and 20-fold for PC7 versus furin). One variant, Asp-49–Arg-42–Arg-45–eglin, exhibited a Ki of 310 pM for furin and blocked furin-dependent processing of von Willebrand factor in COS-1 cells when added to the culture medium of the cells. The exploitation of adventitious contact sites may provide a versatile technique for developing potent, selective inhibitors for newly discovered proteases and could in principle be applied to optimize numerous protein–protein interactions. PMID:12832612

PRACTICAL SIMULATION OF COMPOSTING IN THE LABORATORY

EPA Science Inventory

A closed incubation system was developed for laboratory simulation of composting conditions at the interior of a large compost pile. A conductive heat flux control system (CHFC) was used to adjust the temperature of the internal wall to that of the compost center and compensate f...

Optical contact micrometer

DOEpatents

Jacobson, Steven D.

2014-08-19

Certain examples provide optical contact micrometers and methods of use. An example optical contact micrometer includes a pair of opposable lenses to receive an object and immobilize the object in a position. The example optical contact micrometer includes a pair of opposable mirrors positioned with respect to the pair of lenses to facilitate viewing of the object through the lenses. The example optical contact micrometer includes a microscope to facilitate viewing of the object through the lenses via the mirrors; and an interferometer to obtain one or more measurements of the object.

Finite Element Modeling of a Cylindrical Contact Using Hertzian Assumptions

NASA Technical Reports Server (NTRS)

Knudsen, Erik

2003-01-01

The turbine blades in the high-pressure fuel turbopump/alternate turbopump (HPFTP/AT) are subjected to hot gases rapidly flowing around them. This flow excites vibrations in the blades. Naturally, one has to worry about resonance, so a damping device was added to dissipate some energy from the system. The foundation is now laid for a very complex problem. The damper is in contact with the blade, so now there are contact stresses (both normal and tangential) to contend with. Since these stresses can be very high, it is not all that difficult to yield the material. Friction is another non-linearity and the blade is made out of a Nickel-based single-crystal superalloy that is orthotropic. A few approaches exist to solve such a problem and computer models, using contact elements, have been built with friction, plasticity, etc. These models are quite cumbersome and require many hours to solve just one load case and material orientation. A simpler approach is required. Ideally, the model should be simplified so the analysis can be conducted faster. When working with contact problems determining the contact patch and the stresses in the material are the main concerns. Closed-form solutions for non-conforming bodies, developed by Hertz, made out of isotropic materials are readily available. More involved solutions for 3-D cases using different materials are also available. The question is this: can Hertzian1 solutions be applied, or superimposed, to more complicated problems-like those involving anisotropic materials? That is the point of the investigation here. If these results agree with the more complicated computer models, then the analytical solutions can be used in lieu of the numerical solutions that take a very long time to process. As time goes on, the analytical solution will eventually have to include things like friction and plasticity. The models in this report use no contact elements and are essentially an applied load problem using Hertzian assumptions to

[Effectiveness of interferon-gamma release assays in the tuberculosis contact investigation of elderly people].

PubMed

Seto, Junji; Ahiko, Tadayuki

2014-04-01

To confirm the effectiveness of interferon-gamma release assays (IGRAs) in the tuberculosis (TB) contact investigation of elderly people, we analyzed the results of the QuantiFERON TB Gold in tube (QFT-3G) test, which is a commercially available IGRA. We analyzed the results of the QFT-3G test in 2,420 subjects who were in close contact with TB patients. We investigated subjects with latent TB infection and those showing the onset of TB among the QFT-3G-positive subjects. The QFT-3G-positive rate was 7.3% (95% confidence interval, 6.2%-8.3%). In addition, we demonstrated that the QFT-3G-positive rate increased with age (P < 0.001). The QFT-3G-positive rate was high, particularly in elderly people (> or = 60 years), but the rate was significantly lower than the predicted prevalence of TB infection. Therefore, it was assumed that the QFT-3G test does not always provide a positive result, even in cases of subjects with a previous TB infection. Furthermore, data from the QFT-3G-positive subjects indicated that approximately one half of subjects aged 60-69 years, approximately one-third of those aged 70-79 years, and approximately one-quarter of those aged over 80 years have had recent TB infections. In conclusion, the results of the QFT-3G test in elderly people need to be carefully evaluated according to the contact situation with TB patients; nevertheless, the QFT-3G test is useful for the screening of latent TB infection in elderly people who were in close contact with TB patients.

Crepidula Slipper Limpets Alter Sex Change in Response to Physical Contact with Conspecifics.

PubMed

Carrillo-Baltodano, Allan; Collin, Rachel

2015-12-01

Chemical signaling, especially signaling with waterborne cues, is an important mode of communication between conspecifics of aquatic organisms. Although conspecific associations play an important role in sex allocation of sequential hermaphroditic slipper limpets, the mode of signaling is unknown. We tested the hypothesis that the effects of conspecifics on animal size and time of sex change in the tropical slipper limpet Crepidula cf. marginalis are mediated by waterborne cues. In our experiment, pairs of snails (one small and one large) were kept in cups, either together or partitioned off with fine or coarse mesh, or partitioned, but switched from side to side to allow contact with the cup mate's pedal mucus. The larger snails that were allowed contact with the smaller companions grew faster, and generally changed sex sooner, than did the larger snails in the barrier treatments, which allowed no physical contact. The smaller snails that were allowed contact with the larger cup mate delayed sex change compared to those separated from their cup mates. We were, therefore, able to reject the hypothesis that waterborne cues mediate communication between these snails. Our results suggest that the cue that affects size and time to sex change requires some kind of physical interaction that is lost when the snails are separated. Furthermore, contact with another snail's pedal mucus does not compensate for the loss of physical contact. Since males often attach to the shell of larger females, direct contact may mediate this kind of physical interaction via positional information, physical stimulation, or contact-based chemical communication. Whatever the cue, contact with conspecifics influences both partners, resulting in, surprisingly, a higher growth rate in the larger animal and delayed sex change in the smaller animal. © 2015 Marine Biological Laboratory.

Contact efflorescence as a pathway for crystallization of atmospherically relevant particles

PubMed Central

Davis, Ryan D.; Lance, Sara; Gordon, Joshua A.; Ushijima, Shuichi B.; Tolbert, Margaret A.

2015-01-01

Inadequate knowledge of the phase state of atmospheric particles represents a source of uncertainty in global climate and air quality models. Hygroscopic aqueous inorganic particles are often assumed to remain liquid throughout their atmospheric lifetime or only (re)crystallize at low relative humidity (RH) due to the kinetic limitations of efflorescence (salt crystal nucleation and growth from an aqueous solution). Here we present experimental observations of a previously unexplored heterogeneous nucleation pathway that we have termed “contact efflorescence,” which describes efflorescence initiated by an externally located solid particle coming into contact with the surface of a metastable aqueous microdroplet. This study demonstrates that upon a single collision, contact efflorescence is a pathway for crystallization of atmospherically relevant aqueous particles at high ambient RH (≤80%). Soluble inorganic crystalline particles were used as contact nuclei to induce efflorescence of aqueous ammonium sulfate [(NH4)2SO4], sodium chloride (NaCl), and ammonium nitrate (NH4NO3), with efflorescence being observed in several cases close to their deliquescence RH values (80%, 75%, and 62%, respectively). To our knowledge, these observations represent the highest reported efflorescence RH values for microdroplets of these salts. These results are particularly important for considering the phase state of NH4NO3, where the contact efflorescence RH (∼20–60%) is in stark contrast to the observation that NH4NO3 microdroplets do not homogeneously effloresce, even when exposed to extremely arid conditions (<1% RH). Considering the occurrence of particle collisions in the atmosphere (i.e., coagulation), these observations of contact efflorescence challenge many assumptions made about the phase state of inorganic aerosol. PMID:26668396

Contact efflorescence as a pathway for crystallization of atmospherically relevant particles.

PubMed

Davis, Ryan D; Lance, Sara; Gordon, Joshua A; Ushijima, Shuichi B; Tolbert, Margaret A

2015-12-29

Inadequate knowledge of the phase state of atmospheric particles represents a source of uncertainty in global climate and air quality models. Hygroscopic aqueous inorganic particles are often assumed to remain liquid throughout their atmospheric lifetime or only (re)crystallize at low relative humidity (RH) due to the kinetic limitations of efflorescence (salt crystal nucleation and growth from an aqueous solution). Here we present experimental observations of a previously unexplored heterogeneous nucleation pathway that we have termed "contact efflorescence," which describes efflorescence initiated by an externally located solid particle coming into contact with the surface of a metastable aqueous microdroplet. This study demonstrates that upon a single collision, contact efflorescence is a pathway for crystallization of atmospherically relevant aqueous particles at high ambient RH (≤80%). Soluble inorganic crystalline particles were used as contact nuclei to induce efflorescence of aqueous ammonium sulfate [(NH4)2SO4], sodium chloride (NaCl), and ammonium nitrate (NH4NO3), with efflorescence being observed in several cases close to their deliquescence RH values (80%, 75%, and 62%, respectively). To our knowledge, these observations represent the highest reported efflorescence RH values for microdroplets of these salts. These results are particularly important for considering the phase state of NH4NO3, where the contact efflorescence RH (∼20-60%) is in stark contrast to the observation that NH4NO3 microdroplets do not homogeneously effloresce, even when exposed to extremely arid conditions (<1% RH). Considering the occurrence of particle collisions in the atmosphere (i.e., coagulation), these observations of contact efflorescence challenge many assumptions made about the phase state of inorganic aerosol.

Predicting tularemia with clinical, laboratory and demographical findings in the ED.

PubMed

Yapar, Derya; Erenler, Ali Kemal; Terzi, Özlem; Akdoğan, Özlem; Ece, Yasemin; Baykam, Nurcan

2016-02-01

We aimed to determine clinical, laboratory and demographical characteristics of tularemia on admission to Emergency Department (ED). Medical data of 317 patients admitted to ED and subsequently hospitalized with suspected tularemia between January 1, 2011, and May 31, 2015, were collected. Patients were divided into 2 groups according to microagglutination test results, as tularemia (+) and tularemia (-). Of the 317 patients involved, 49 were found to be tularemia (+) and 268 were tularemia (-). Mean age of the tularemia (+) patients was found to be higher than that of tularemia (-) patients. When compared to tularemia (-) patients, a significant portion of patients in tularemia (+) patients were elderly, living in rural areas and had contact with rodents. When clinical and laboratory findings of the 2 groups were compared, any statistical significance could not be determined. Tularemia is a disease of elderly people living in rural areas. Contact with rodents also increases risk of tularemia in suspected patients. Copyright © 2015 Elsevier Inc. All rights reserved.

Dual-joint modeling for estimation of total knee replacement contact forces during locomotion.

PubMed

Hast, Michael W; Piazza, Stephen J

2013-02-01

Model-based estimation of in vivo contact forces arising between components of a total knee replacement is challenging because such forces depend upon accurate modeling of muscles, tendons, ligaments, contact, and multibody dynamics. Here we describe an approach to solving this problem with results that are tested by comparison to knee loads measured in vivo for a single subject and made available through the Grand Challenge Competition to Predict in vivo Tibiofemoral Loads. The approach makes use of a "dual-joint" paradigm in which the knee joint is alternately represented by (1) a ball-joint knee for inverse dynamic computation of required muscle controls and (2) a 12 degree-of-freedom (DOF) knee with elastic foundation contact at the tibiofemoral and patellofemoral articulations for forward dynamic integration. Measured external forces and kinematics were applied as a feedback controller and static optimization attempted to track measured knee flexion angles and electromyographic (EMG) activity. The resulting simulations showed excellent tracking of knee flexion (average RMS error of 2.53 deg) and EMG (muscle activations within ±10% envelopes of normalized measured EMG signals). Simulated tibiofemoral contact forces agreed qualitatively with measured contact forces, but their RMS errors were approximately 25% of the peak measured values. These results demonstrate the potential of a dual-joint modeling approach to predict joint contact forces from kinesiological data measured in the motion laboratory. It is anticipated that errors in the estimation of contact force will be reduced as more accurate subject-specific models of muscles and other soft tissues are developed.

Risk Factors for SARS among Persons without Known Contact with SARS Patients, Beijing, China

PubMed Central

Wu, Jiang; Xu, Fujie; Zhou, Weigong; Feikin, Daniel R.; Lin, Chang-Ying; He, Xiong; Zhu, Zonghan; Liang, Wannian; Chin, Daniel P.

2004-01-01

Most cases of severe acute respiratory syndrome (SARS) have occurred in close contacts of SARS patients. However, in Beijing, a large proportion of SARS cases occurred in persons without such contact. We conducted a case-control study in Beijing that compared exposures of 94 unlinked, probable SARS patients with those of 281 community-based controls matched for age group and sex. Case-patients were more likely than controls to have chronic medical conditions or to have visited fever clinics (clinics at which possible SARS patients were separated from other patients), eaten outside the home, or taken taxis frequently. The use of masks was strongly protective. Among 31 case-patients for whom convalescent-phase (>21 days) sera were available, 26% had immunoglobulin G to SARS-associated coronavirus. Our finding that clinical SARS was associated with visits to fever clinics supports Beijing’s strategy of closing clinics with poor infection-control measures. Our finding that mask use lowered the risk for disease supports the community’s use of this strategy. PMID:15030685

Contact reactions to fragrances.

PubMed

Katsarou, A; Armenaka, M; Kalogeromitros, D; Koufou, V; Georgala, S

1999-05-01

The most common reaction to fragrances is contact dermatitis, a delayed hypersensitivity reaction; however, other reactions include immediate contact reactions (contact urticaria) and photo-allergic reactions. Fragrance mix (FM) and balsam of Peru (BP) are used to screen for fragrance allergy. To study the different types of allergic skin reactions to fragrance compounds. Delayed hypersensitivity reactions to FM and BP were studied in 4,975 patients with suspected contact dermatitis by routine patch testing interpreted at 48 and 96 hours. In 664 of the patients, patch tests were read at 30 minutes to evaluate for immediate (wheal-and-flare) contact reactions and again at 48 and 96 hours. Photopatch tests to FM were performed in 111 patients with suspected photo-allergic dermatitis. Delayed contact reactions to FM occurred in 6.6% of females and 5.4% of males and to BP in 3.9% of females and 4.1% of males. Analysis of data over time (12 study years) showed an increased trend for reactions to fragrances, particularly in males. Sensitivity to other contact allergens (polysensitivity) was found in 62% of patients and polysensitivity presented more often with generalized contact dermatitis. The most sensitizing components of the fragrance mix that were tested in 38 patients were cinnamic alcohol, oak moss, and cinnamic aldehyde. There were 112 immediate patch test reactions to FM and 113 to BP in 664 patients. Immediate contact reactions were followed by delayed contact reactions in 13.4% of patients for FM and 8.8% for BP, representing a significant increase in the frequency of delayed contact reactions. Patients with immediate contact reactions to fragrances did not have a higher incidence of atopy (25.9%). No cases of positive photopatch test reactions to FM were seen. Fragrances commonly cause both delayed and immediate patch test reactions and patients with immediate contact reactions have an increase in delayed contact reactions to the same allergen.

Postural stabilization from fingertip contact II. Relationships between age, tactile sensibility and magnitude of contact forces.

PubMed

Tremblay, François; Mireault, Annie-Claude; Dessureault, Liam; Manning, Hélène; Sveistrup, Heidi

2005-07-01

In the present report, we extend our previous observations on the effect of age on postural stabilization from fingertip contact (Exp Brain Res 157 (2004) 275) to examine the possible influence of sensory thresholds measured at the fingertip on the magnitude of contact forces. Participants (young, n=25, 19-32 years; old, n=35, 60-86 years) underwent psychophysical testing of the right index finger to determine thresholds for spatial acuity, pressure sensitivity and kinesthetic acuity. Spatial acuity was determined from the ability to detect gaps of different widths, while Semmes-Weinstein monofilaments were used for pressure sensitivity. Kinesthetic acuity was determined by asking participants to discriminate plates of different thicknesses using a thumb-index precision grip. These tests were selected on the basis that each reflected different sensory coding mechanisms (resolution of spatial stimuli, detection of mechanical forces and integration of multi-sensory inputs for hand conformation) and thus provided specific information about the integrity and function of mechanoreceptive afferents innervating the hand. After log transformation, thresholds were first examined to determine the influence of age (young and old) and gender (male, female) on tactile acuity. Sensory thresholds were then entered into multiple linear regression models to examine their ability to predict fingertip contact forces (normal and tangential) applied to a smooth surface when subjects stood with eyes closed on either a firm or a compliant support surface. As expected, age exerted a significant effect (p<0.01) on all three thresholds, but its impact was greater on spatial acuity than on pressure sensitivity or kinesthetic acuity. Gender had a marginal impact on pressure sensitivity thresholds only. The regression analyses revealed that tactile thresholds determined at the index fingertip accounted for a substantial proportion of the variance (up to 30%) seen in the contact forces deployed

77 FR 33810 - Art Advisory Panel-Notice of Availability of Report of 2011 Closed Meetings

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-07

... DEPARTMENT OF THE TREASURY Internal Revenue Service Art Advisory Panel--Notice of Availability of..., the Government in the Sunshine Act, a report summarizing the closed meeting activities of the Art... at www.irs.gov . FOR FURTHER INFORMATION CONTACT: Ruth Vriend, AP:TPV:ART, Internal Revenue Service...

Contact structure for use in catalytic distillation

DOEpatents

Jones, Jr., Edward M.

1984-01-01

A method for conducting catalytic chemical reactions and fractionation of the reaction mixture comprising feeding reactants into a distillation column reactor contracting said reactant in liquid phase with a fixed bed catalyst in the form of a contact catalyst structure consisting of closed porous containers containing the catatlyst for the reaction and a clip means to hold and support said containers, which are disposed above, i.e., on the distillation trays in the tower. The trays have weir means to provide a liquid level on the trays to substantially cover the containers. In other words, the trays function in their ordinary manner with the addition thereto of the catalyst. The reaction mixture is concurrently fractionated in the column.

Contact with turf algae alters the coral microbiome: contact versus systemic impacts

NASA Astrophysics Data System (ADS)

Pratte, Zoe A.; Longo, Guilherme O.; Burns, Andrew S.; Hay, Mark E.; Stewart, Frank J.

2018-03-01

Coral reefs are degrading to algae-dominated reefs worldwide, with alterations of coral microbiomes commonly co-occurring with reef demise. The severe thermal anomaly during the 2016 El Niño event in the South Pacific killed many corals and stressed others. We examined the microbiome of turf algae and of the coral Porites sp. in contact with turf during this thermal event to investigate algal turf effects on the coral microbiome during a period of environmental stress. The microbial composition of turf did not differ between coral-contacted and non-contacted turfs. However, microbiomes of corals in direct contact with turf were similar to those of the turf microbiome, but differed significantly from coral portions 5 cm from the point of turf/coral contact and from portions of the coral that looked most healthy, regardless of location. Although the majority of significant differences occurred in coral samples at the point of contact, a small subset of microbial taxa was enriched in coral tissues taken 5 cm from turf contact compared to all other sample types, including samples from areas of the coral that appeared most healthy. These results suggest that the coral microbiome is susceptible to colonization by microbes from turf, but not vice versa. Results also suggest that algal contact elicits a subtle shift in the coral microbiome just beyond the contact site. The combination of turf microbiome stability and coral microbiome vulnerability at areas of contact may contribute to the continued decline in coral cover and increase in algal cover associated with coral-algae phase shifts.

Contact Resistance Evolution and Degradation of Highly Cycled Micro-Contacts

DTIC Science & Technology

2014-03-27

i List of Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii I. Introduction...scanning electron microscope EDS energy dispersive X-ray spectroscopy ii CONTACT RESISTANCE EVOLUTION AND DEGRADATION OF HIGHLY CYCLED MICRO-CONTACTS I