Science.gov

Sample records for laboratory high explosives

  1. Capabilities for high explosive pulsed power research at Los Alamos National Laboratory

    SciTech Connect

    Goforth, James H; Oona, Henn; Tasker, Douglas G; Kaul, A M

    2008-01-01

    Research on topics requiring high magnetic fields and high currents have been pursued using high explosive pulsed power (HEPP) techniques since the 1950s at Los Alamos National Laboratory. We have developed many sophisticated HEPr systems through the years, and most of them depend on technology available from the nuclear weapons program. Through the 1980s and 1990s, our budgets would sustain parallel efforts in zpinch research using both HEPr and capacitor banks. In recent years, many changes have occurred that are driven by concerns such as safety, security, and environment, as well as reduced budgets and downsizing of the National Nuclear Security Administration (NNSA) complex due to the end of the cold war era. In this paper, we review the teclmiques developed to date, and adaptations that are driven by changes in budgets and our changing complex. One new Ranchero-based solid liner z-pinch experimental design is also presented. Explosives that are cast to shape instead of being machined, and initiation systems that depend on arrays of slapper detonators are important new tools. Some materials that are seen as hazardous to the environment are avoided in designs. The process continues to allow a wide range of research however, and there are few, if any, experiments that we have done in the past that could not be perform today. The HErr firing facility at Los Alamos continues to have a 2000 lb. high explosive limit, and our 2.4 MJ capacitor bank remains a mainstay of the effort. Modem diagnostic and data analysis capabilities allow fewer personnel to achieve better results, and in the broad sense we continue to have a robust capability.

  2. New 100 mm Gun Assembly Installation at Lawrence Livermore National Laboratory High Explosives Applications Facility

    SciTech Connect

    Vandersall, K S; Lee, R A; Chiao, P I; Garcia, F; Travis, J O; Forbes, J W

    2003-10-28

    A new 100mm gun assembly was recently installed and tested at Lawrence Livermore National Laboratories located in the High Explosives Applications Facility (HEAF). Thiot Ingenierie performed the design of the replacement barrel, based on improvements to the initial design. This design incorporated barrel and breech sections forged from CLARM series high-strength alloys obtained from Tecphy Corporation and machined by Manufacture de Forage. Part of the improvement of the design was implementing a laser alignment system for quick and accurate barrel alignment checks. This laser is also used to align the target assembly. This paper will detail the design changes incorporated into the installation, the testing process, and future direction of research for the new gun.

  3. Remedial investigation of the High-Explosives (HE) Process Area, Lawrence Livermore National Laboratory Site 300

    SciTech Connect

    Crow, N.B.; Lamarre, A.L.

    1990-08-01

    This report presents the results of a Remedial Investigation (RI) to define the extent of high explosives (HE) compounds and volatile organic compounds (VOCs) found in the soil, rocks, and ground water of the HE Process Area of Lawrence Livermore National Laboratory's (LLNL) Site 300 Facility. The report evaluates potential public health environmental risks associated with these compounds. Hydrogeologic information available before February 15, 1990, is included; however, chemical analyses and water-level data are reported through March 1990. This report is intended to assist the California Regional Water Quality Control Board (RWQCB)--Central Valley Region and the US Environmental Protection Agency (EPA) in evaluating the extent of environmental contamination of the LLNL HE Process Area and ultimately in designing remedial actions. 90 refs., 20 figs., 7 tabs.

  4. Lightning Protection Certification for High Explosives Facilities at Lawrence Livermore National Laboratory

    SciTech Connect

    Clancy, T J; Brown, C G; Ong, M M; Clark, G A

    2006-01-11

    Presented here is an innovation in lighting safety certification, and a description of its implementation for high explosives processing and storage facilities at Lawrence Livermore National Laboratory. Lightning rods have proven useful in the protection of wooden structures; however, modern structures made of rebar, concrete, and the like, require fresh thinking. Our process involves a rigorous and unique approach to lightning safety for modern buildings, where the internal voltages and currents are quantified and the risk assessed. To follow are the main technical aspects of lightning protection for modern structures and these methods comply with the requirements of the National Fire Protection Association, the National Electrical Code, and the Department of Energy [1][2]. At the date of this release, we have certified over 70 HE processing and storage cells at our Site 300 facility.

  5. High-nitrogen explosives

    SciTech Connect

    Naud, D.; Hiskey, M. A.; Kramer, J. F.; Bishop, R. L.; Harry, H. H.; Son, S. F.; Sullivan, G. K.

    2002-01-01

    The syntheses and characterization of various tetrazine and furazan compounds offer a different approach to explosives development. Traditional explosives - such as TNT or RDX - rely on the oxidation of the carbon and hydrogen atoms by the oxygen carrying nitro group to produce the explosive energy. High-nitrogen compounds rely instead on large positive heats of formation for that energy. Some of these high-nitrogen compounds have been shown to be less sensitive to initiation (e.g. by impact) when compared to traditional nitro-containing explosives of similar performances. Using the precursor, 3,6-bis-(3,5-dimethylpyrazol-1-yl)-s-tetrazine (BDT), several useful energetic compounds based on the s-tetrazine system have been synthesized and studied. The compound, 3,3{prime}-azobis(6-amino-s-tetrazine) or DAAT, detonates as a half inch rate stick despite having no oxygen in the molecule. Using perfluoroacetic acid, DAAT can be oxidized to give mixtures of N-oxide isomers (DAAT03.5) with an average oxygen content of about 3.5. This energetic mixture burns at extremely high rates and with low dependency on pressure. Another tetrazine compound of interest is 3,6-diguanidino-s-tetrazine(DGT) and its dinitrate and diperchlorate salts. DGT is easily synthesized by reacting BDT with guanidine in methanol. Using Caro's acid, DGT can be further oxidized to give 3,6-diguanidino-s-tetrazine-1,4-di-N-oxide (DGT-DO). Like DGT, the di-N-oxide can react with nitric acid or perchloric acid to give the dinitrate and the diperchlorate salts. The compounds, 4,4{prime}-diamino-3,3{prime}-azoxyfurazan (DAAF) and 4,4{prime}-diamino-3,3{prime}-azofurazan (DAAzF), may have important future roles in insensitive explosive applications. Neither DAAF nor DAAzF can be initiated by laboratory impact drop tests, yet both have in some aspects better explosive performances than 1,3,5-triamino-2,4,6-trinitrobenzene TATB - the standard of insensitive high explosives. The thermal stability of DAAzF is

  6. Photographic laboratory studies of explosions.

    NASA Technical Reports Server (NTRS)

    Kamel, M. M.; Oppenheim, A. K.

    1973-01-01

    Description of a series of cinematographic studies of explosions made with a high-speed rotating-mirror streak camera which uses a high-frequency stroboscopic ruby laser as the light source. The results obtained mainly concern explosions initiated by focused laser irradiation from a pulsed neodymium laser in a detonating gas consisting essentially of an equimolar mixture of acetylene and oxygen at an initial pressure of 100 torr at room temperature. Among the most significant observations were observations of a spherical blast wave preceded by a Chapman-Jouguet detonation which is stabilized immediately after initiation, the merging of a spherical flame with a shock front of the blast wave in which the flame is propagating, the division of a spherical detonation front into a shock wave and flame, and the generation of shock waves by a network of spherical flames.

  7. Closure plan for the decommissioned high explosives rinse-water lagoons at Lawrence Livermore National Laboratory Site 300

    SciTech Connect

    Carpenter, D.W.; Lamarre, A.L.; Crow, N.B.; Swearengen, P.M.

    1988-05-31

    The High Explosives (HE) Process Area is a major facility at Lawrence Livermore National Laboratory (LLNL) Site 300. Within the Process Area, rinse water from various buildings formerly was discharged to nine relatively small, unlined lagoons where it was disposed of by evaporation and infiltration. In 1985, LLNL decommissioned these lagoons and diverted the rinse waters to two doubly lined surface impoundments. LLNL conducted the hydrogeologic investigations required to support the permanent closure of the none decommissioned lagoons. These studies included drilling ground water monitoring wells and extensively collecting soil and rock samples, which were analyzed for EPA toxic metals, HE compounds, and purgeable and extractable priority organic pollutants. On October 26, 1987, the RWQCB requested that we prepare a comprehensive report to summarize and discuss the findings of the LLNL HE Process Area Investigation. This report is our response to the Board's request. 22 refs., 19 figs. , 45 tabs.

  8. Avian community composition in response to high explosive testing operations at Los Alamos National Laboratory in Northern New Mexico

    DOE PAGESBeta

    Keller, David C.; Fresquez, Philip R.; Hansen, Leslie A.; Kaschube, Danielle R.

    2015-12-28

    Breeding bird abundance, species richness, evenness, diversity, composition, productivity, and survivorship were determined near a high-explosive detonation site at Los Alamos National Laboratory, New Mexico, USA, during pre-operation (1997-1999) and operation (2000-2014) periods. The operation periods consisted of detonations (<23 kg in yield and <3 per breeding season) in open air (2000-2002), within foam containment (2003-2006) and within steel vessel containment (2007-2014) systems; the latter two were employed to reduce noise and dispersal of high-explosives residues. A total of 2952 bird captures, representing 80 species, was recorded during 18 years of mist net operations using the Monitoring Avian Productivity andmore » Survivorship protocol. Individuals captured were identified to species, aged, sexed, and banded during May through August of each year. There were no significant differences (p > 0.05) in mean avian abundance and species evenness in any of the operation periods as compared with the pre-operation period. Species richness and diversity were significantly higher (p < 0.05) during the vessel containment period (2007-2014) than the pre-operation period. The time period of this study coincided with a wildfire (2000), a bark beetle infestation (2002), and two periods of drought (Nov 1999-Mar 2004 and Dec 2005-Dec 2014) that affected the study area. Furthermore, analysis of aerial photos determined that the average percent canopy cover of mature ponderosa pines (Pinus ponderosa) within 100 feet of mist net sites declined from 12% to 3% between 1991 and 2014 and the percent cover of shrubs slightly increased.« less

  9. Environmental Assessment for the High Explosives Wastewater Treatment Facility, Los Alamos National Laboratory, Los Alamos, New Mexico

    SciTech Connect

    1995-08-03

    The Department of Energy (DOE) has identified a need to improve the management of wastewater resulting from high explosives (HE) research and development work at Los Alamos National Laboratory (LANL). LANL`s current methods off managing HE-contaminated wastewater cannot ensure that discharged HE wastewater would consistently meet the Environmental Protection Agency`s (EPA`s) standards for wastewater discharge. The DOE needs to enhance He wastewater management to e able to meet both present and future regulatory standards for wastewater discharge. The DOE also proposes to incorporate major pollution prevention and waste reduction features into LANL`s existing HE production facilities. Currently, wastewater from HE processing buildings at four Technical Areas (TAs) accumulates in sumps where particulate HE settles out and barium is precipitated. Wastewater is then released from the sumps to the environment at 15 permitted outfalls without treatment. The released water may contain suspended and dissolved contaminants, such as HE and solvents. This Environmental Assessment (EA) analyzes two alternatives, the Proposed Action and the Alternative Action, that would meet the purpose and need for agency action. Both alternatives would treat all HE process wastewater using sand filters to remove HE particulates and activated carbon to adsorb organic solvents and dissolved HE. Under either alternative, LANL would burn solvents and flash dried HE particulates and spent carbon following well-established procedures. Burning would produce secondary waste that would be stored, treated, and disposed of at TA-54, Area J. This report contains the Environmental Assessment, as well as the Finding of No Significant Impact and Floodplain Statement of Findings for the High Explosives Wastewater Treatment Facility.

  10. Avian community composition in response to high explosive testing operations at Los Alamos National Laboratory in Northern New Mexico

    SciTech Connect

    Keller, David C.; Fresquez, Philip R.; Hansen, Leslie A.; Kaschube, Danielle R.

    2015-12-28

    Breeding bird abundance, species richness, evenness, diversity, composition, productivity, and survivorship were determined near a high-explosive detonation site at Los Alamos National Laboratory, New Mexico, USA, during pre-operation (1997-1999) and operation (2000-2014) periods. The operation periods consisted of detonations (<23 kg in yield and <3 per breeding season) in open air (2000-2002), within foam containment (2003-2006) and within steel vessel containment (2007-2014) systems; the latter two were employed to reduce noise and dispersal of high-explosives residues. A total of 2952 bird captures, representing 80 species, was recorded during 18 years of mist net operations using the Monitoring Avian Productivity and Survivorship protocol. Individuals captured were identified to species, aged, sexed, and banded during May through August of each year. There were no significant differences (p > 0.05) in mean avian abundance and species evenness in any of the operation periods as compared with the pre-operation period. Species richness and diversity were significantly higher (p < 0.05) during the vessel containment period (2007-2014) than the pre-operation period. The time period of this study coincided with a wildfire (2000), a bark beetle infestation (2002), and two periods of drought (Nov 1999-Mar 2004 and Dec 2005-Dec 2014) that affected the study area. Furthermore, analysis of aerial photos determined that the average percent canopy cover of mature ponderosa pines (Pinus ponderosa) within 100 feet of mist net sites declined from 12% to 3% between 1991 and 2014 and the percent cover of shrubs slightly increased.

  11. Simulating intracrater ash recycling during mid-intensity explosive activity: high temperature laboratory experiments on natural basaltic ash

    NASA Astrophysics Data System (ADS)

    D'Oriano, Claudia; Pompilio, Massimo; Bertagnini, Antonella; Cioni, Raffaello; Pichavant, Michel

    2010-05-01

    Direct observations of mid-intensity eruptions, in which a huge amount of ash is generated, indicate that ash recycling is quite common. The recognition of juvenile vs. recycled fragments is not straightforward, and no unequivocal, widely accepted criteria exist to support this. The presence of recycled glassy fragments can hide primary magmatic information, introducing bias in the interpretations of the ongoing magmatic and volcanic activity. High temperature experiments were performed at atmospheric pressure on natural samples to investigate the effects of reheating on morphology, texture and composition of volcanic ash. Experiments simulate the transformation of juvenile glassy fragments that, falling into the crater or in the upper part of the conduit, are recycled by following explosions. Textural and compositional modifications obtained in laboratory are compared with similar features observed in natural samples in order to identify some main general criteria to be used for the discrimination of recycled material. Experiments were carried out on tephra produced during Strombolian activity, fire fountains and continuous ash emission at Etna, Stromboli and Vesuvius. Coarse glassy clasts were crushed in a nylon mortar in order to create an artificial ash, and then sieved to select the size interval of 1-0.71 mm. Ash shards were put in a sealed or open quartz tube, in order to prevent or to reproduce effects of air oxidation. The tube was suspended in a HT furnace at INGV-Pisa and kept at different temperatures (up to to 1110°C) for increasing time (0.5-12 hours). Preliminary experiments were also performed under gas flux conditions. Optical and electron microscope observations indicate that high temperature and exposure to the air induce large modifications on clast surface, ranging from change in color, to incipient plastic deformation till complete sintering. Significant change in color of clasts is strictly related to the presence of air, irrespective of

  12. NEW GUN CAPABILITY WITH INTERCHANGABLE BARRELS TO INVESTIGATE LOW VELOCITY IMPACT REGIMES AT THE LAWRENCE LIVERMORE NATIONAL LABORATORY HIGH EXPLOSIVES APPLICATIONS FACILITY

    SciTech Connect

    Vandersall, K S; Behn, A; Gresshoff, M; Jr., L F; Chiao, P I

    2009-09-16

    A new gas gun capability is being activated at Lawrence Livermore National Laboratories located in the High Explosives Applications Facility (HEAF). The single stage light gas (dry air, nitrogen, or helium) gun has interchangeable barrels ranging from 25.4 mm to 76.2 mm in diameter with 1.8 meters in length and is being fabricated by Physics Applications, Inc. Because it is being used for safety studies involving explosives, the gun is planned for operation inside a large enclosed firing tank, with typical velocities planned in the range of 10-300 m/s. Three applications planned for this gun include: low velocity impact of detonator or detonator/booster assemblies with various projectile shapes, the Steven Impact test that involves impact initiation of a cased explosive target, and the Taylor impact test using a cylindrical explosive sample impacted onto a rigid anvil for fracture studies of energetic materials. A highlight of the gun features, outline on work in progress for implementing this capability, and discussion of the planned areas of research will be included.

  13. Novel high explosive compositions

    DOEpatents

    Perry, D.D.; Fein, M.M.; Schoenfelder, C.W.

    1968-04-16

    This is a technique of preparing explosive compositions by the in-situ reaction of polynitroaliphatic compounds with one or more carboranes or carborane derivatives. One or more polynitroaliphatic reactants are combined with one or more carborane reactants in a suitable container and mixed to a homogeneous reaction mixture using a stream of inert gas or conventional mixing means. Ordinarily the container is a fissure, crack, or crevice in which the explosive is to be implanted. The ratio of reactants will determine not only the stoichiometry of the system, but will effect the quality and quantity of combustion products, the explosive force obtained as well as the impact sensitivity. The test values can shift with even relatively slight changes or modifications in the reaction conditions. Eighteen illustrative examples accompany the disclosure. (46 claims)

  14. Designing for explosive safety'': The Explosive Components Facility at Sandia National Laboratories

    SciTech Connect

    Couch, W.A.

    1990-12-01

    The Explosive Components Facility (ECF) is to be a new major facility in the Sandia National Laboratories (SNL) Weapons Program. The ECF is a self-contained, secure site on SNL property and is surrounded by Kirtland Air Force Base which is located 6-1/2 miles east of downtown Albuquerque, New Mexico. The ECF will be dedicated to research, development, and testing of detonators, neutron generators, batteries, explosives, and other weapon components. It will have capabilities for conducting explosive test fires, gas gun testing, physical analyses, chemical analyses, electrical testing and ancillary explosive storage in magazines. The ECF complex is composed of a building covering an area of approximately 91,000 square feet, six exterior explosive service magazines and a remote test cell. Approximately 50% of the building space will be devoted to highly specialized laboratory and test areas, the other 50% of the building is considered nonhazardous. Critical to the laboratory and test areas are the blast-structural design consideration and operational considerations, particularly those concerning personnel access control, safety and environmental protection. This area will be decoupled from the rest of the building to the extent that routine tests will not be heard or felt in the administrative area of the building. While the ECF is designed in accordance with the DOE Explosives Safety Manual to mitigate any off-site blast effects, potential injuries or death to the ECF staff may result from an accidental detonation of explosive material within the facility. Therefore, reducing the risk of exposing operation personnel to hazardous and energetic material is paramount in the design of the ECF.

  15. High explosive compound

    DOEpatents

    Crawford, Theodore C.

    1976-01-01

    1. A low detonation velocity explosive consisting essentially of a particulate mixture of ortho-boric acid and trinitrotoluene, said mixture containing from about 25 percent to about 65 percent by weight of ortho-boric acid, said ortho-boric acid comprised of from 60 percent to 90 percent of spherical particles having a mean particle size of about 275 microns and 10 percent to 40 percent of spherical particles having a particle size less than about 44 microns.

  16. Securing Infrastructure from High Explosive Threats

    SciTech Connect

    Glascoe, L; Noble, C; Reynolds, J; Kuhl, A; Morris, J

    2009-03-20

    Lawrence Livermore National Laboratory (LLNL) is working with the Department of Homeland Security's Science and Technology Directorate, the Transportation Security Administration, and several infrastructure partners to characterize and help mitigate principal structural vulnerabilities to explosive threats. Given the importance of infrastructure to the nation's security and economy, there is a clear need for applied research and analyses (1) to improve understanding of the vulnerabilities of these systems to explosive threats and (2) to provide decision makers with time-critical technical assistance concerning countermeasure and mitigation options. Fully-coupled high performance calculations of structural response to ideal and non-ideal explosives help bound and quantify specific critical vulnerabilities, and help identify possible corrective schemes. Experimental validation of modeling approaches and methodologies builds confidence in the prediction, while advanced stochastic techniques allow for optimal use of scarce computational resources to efficiently provide infrastructure owners and decision makers with timely analyses.

  17. Explosion Heat and Metal Acceleration Ability of High Explosives

    NASA Astrophysics Data System (ADS)

    Makhov, M. N.

    2004-07-01

    Investigations of explosion heats of TNT and HMX show that in tests of unconfined charges the explosion products undergo intense secondary heating when approaching the wall of calorimetric bomb cavity. This secondary heating causes "re-freezing" the explosion products in conditions of low pressure. An inert metal casing whose mass is more than four times greater than that of explosive charge prevents the secondary heating of products to the "re-freezing" temperature and rules out a change in their composition. Filling of calorimetric bomb cavity before explosion with an inert gas produces an effect similar to that of charge casing. The value of explosion heat, measured under conditions that preclude "re-freezing" of explosion products can serve as a measure of the energy content of high explosive. With the use of this parameter a simple method for predicting explosive performance in Cylinder Test has been developed. The method is based on the assumption that the coefficient of conversion of the chemical energy to the kinetic energy depends on the volumetric mole number of gaseous products.

  18. Insensitive fuze train for high explosives

    DOEpatents

    Cutting, Jack L.; Lee, Ronald S.; Von Holle, William G.

    1994-01-01

    A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124.

  19. Insensitive fuze train for high explosives

    DOEpatents

    Cutting, J.L.; Lee, R.S.; Von Holle, W.G.

    1994-01-04

    A generic insensitive fuze train to initiate insensitive high explosives, such as PBXW-124 is described. The insensitive fuze train uses a slapper foil to initiate sub-gram quantities of an explosive, such as HNS-IV or PETN. This small amount of explosive drives a larger metal slapper onto a booster charge of an insensitive explosive, such as UF-TATB. The booster charge initiates a larger charge of an explosive, such as LX-17, which in turn, initiates the insensitive high explosive, such as PBXW-124. 3 figures.

  20. High temperature two component explosive

    DOEpatents

    Mars, James E.; Poole, Donald R.; Schmidt, Eckart W.; Wang, Charles

    1981-01-01

    A two component, high temperature, thermally stable explosive composition comprises a liquid or low melting oxidizer and a liquid or low melting organic fuel. The oxidizer and fuel in admixture are incapable of substantial spontaneous exothermic reaction at temperatures on the order of 475.degree. K. At temperatures on the order of 475.degree. K., the oxidizer and fuel in admixture have an activation energy of at least about 40 kcal/mol. As a result of the high activation energy, the preferred explosive compositions are nondetonable as solids at ambient temperature, and become detonable only when heated beyond the melting point. Preferable oxidizers are selected from alkali or alkaline earth metal nitrates, nitrites, perchlorates, and/or mixtures thereof. Preferred fuels are organic compounds having polar hydrophilic groups. The most preferred fuels are guanidinium nitrate, acetamide and mixtures of the two. Most preferred oxidizers are eutectic mixtures of lithium nitrate, potassium nitrate and sodium nitrate, of sodium nitrite, sodium nitrate and potassium nitrate, and of potassium nitrate, calcium nitrate and sodium nitrate.

  1. PINS Measurements and Simulations for Stand-Off Detection of High Explosives

    SciTech Connect

    E.H. Seabury

    2011-07-01

    There has been some interest in the ability of Idaho National Laboratory's (INL) Portable Isotopic Neutron Spectroscopy System's (PINS) ability to detect high explosives at a distance. In order to assess the system's ability to perform this task, laboratory experiments on simulated or mock explosives and Monte Carlo simulations using MCNP on both mock and real explosives have been performed. The simulations and experiments on mock explosives have essentially identical configurations, allowing the models to be confirmed with experiment. This provides greater confidence in the simulations on real explosives without the need for experiment on live explosives.

  2. Quality assurance testing of an explosives trace analysis laboratory--further improvements to include peroxide explosives.

    PubMed

    Crowson, Andrew; Cawthorne, Richard

    2012-12-01

    The Forensic Explosives Laboratory (FEL) operates within the Defence Science and Technology Laboratory (DSTL) which is part of the UK Government Ministry of Defence (MOD). The FEL provides support and advice to the Home Office and UK police forces on matters relating to the criminal misuse of explosives. During 1989 the FEL established a weekly quality assurance testing regime in its explosives trace analysis laboratory. The purpose of the regime is to prevent the accumulation of explosives traces within the laboratory at levels that could, if other precautions failed, result in the contamination of samples and controls. Designated areas within the laboratory are swabbed using cotton wool swabs moistened with ethanol:water mixture, in equal amounts. The swabs are then extracted, cleaned up and analysed using Gas Chromatography with Thermal Energy Analyser detectors or Liquid Chromatography with triple quadrupole Mass Spectrometry. This paper follows on from two previous published papers which described the regime and summarised results from approximately 14years of tests. This paper presents results from the subsequent 7years setting them within the context of previous results. It also discusses further improvements made to the systems and procedures and the inclusion of quality assurance sampling for the peroxide explosives TATP and HMTD. Monitoring samples taken from surfaces within the trace laboratories and trace vehicle examination bay have, with few exceptions, revealed only low levels of contamination, predominantly of RDX. Analysis of the control swabs, processed alongside the monitoring swabs, has demonstrated that in this environment the risk of forensic sample contamination, assuming all the relevant anti-contamination procedures have been followed, is so small that it is considered to be negligible. The monitoring regime has also been valuable in assessing the process of continuous improvement, allowing sources of contamination transfer into the trace

  3. Chemical Structure and Accidental Explosion Risk in the Research Laboratory

    ERIC Educational Resources Information Center

    Churchill, David G.

    2006-01-01

    Tips that laboratory researchers and beginning graduate students can use to safeguard against explosion hazard with emphasis on clear illustrations of molecular structure are discussed. Those working with hazardous materials must proceed cautiously and may want to consider alternative and synthetic routes.

  4. High-explosive driven crowbar switch

    DOEpatents

    Dike, Robert S.; Kewish, Jr., Ralph W.

    1976-01-13

    The disclosure relates to a compact explosive driven switch for use as a low resistance, low inductance crowbar switch. A high-explosive charge extrudes a deformable conductive metallic plate through a polyethylene insulating layer to achieve a hard current contact with a supportive annular conductor.

  5. Detonation in shocked homogeneous high explosives

    SciTech Connect

    Yoo, C.S.; Holmes, N.C.; Souers, P.C.

    1995-11-01

    We have studied shock-induced changes in homogeneous high explosives including nitromethane, tetranitromethane, and single crystals of pentaerythritol tetranitrate (PETN) by using fast time-resolved emission and Raman spectroscopy at a two-stage light-gas gun. The results reveal three distinct steps during which the homogeneous explosives chemically evolve to final detonation products. These are (1) the initiation of shock compressed high explosives after an induction period, (2) thermal explosion of shock-compressed and/or reacting materials, and (3) a decay to a steady-state representing a transition to the detonation of uncompressed high explosives. Based on a gray-body approximation, we have obtained the CJ temperatures: 3800 K for nitromethane, 2950 K for tetranitromethane, and 4100 K for PETN. We compare the data with various thermochemical equilibrium calculations. In this paper we will also show a preliminary result of single-shot time-resolved Raman spectroscopy applied to shock-compressed nitromethane.

  6. Explosive Components Facility at Sandia National Laboratories, Albuquerque, New Mexico

    SciTech Connect

    Not Available

    1992-07-01

    The United States Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Explosive Components Facility (ECF) at the Sandia National Laboratories, Albuquerque (SNL). This facility is needed to integrate, centralize, and enhance many of the explosive, neutron generation, and weapons testing programs currently in progress at SNL. In general, there is insufficient space in existing facilities for the development and testing activities required by modern explosives technologies. The EA examined the potential environmental impacts of the proposed ECF project and discussed potential alternatives. Based on the analyses in the EA, DOE has determined that the proposed action does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969, and CEQ regulations at 40 CFR 1508.18 and 1508.27. Therefore, an environmental impact statement (EIS) is not required, and the DOE is issuing this Finding of No Significant Impact (FONSI).

  7. Radio frequency overview of the high explosive radio telemetry project

    SciTech Connect

    Bracht, R.; Dimsdle, J.; Rich, D.; Smith, F.

    1998-12-31

    High explosive radio telemetry (HERT) is a project that is being developed jointly by Los Alamos National Laboratory and AlliedSignal Federal Manufacturing and Technologies. The ultimate goal is to develop a small, modular telemetry system capable of high-speed detection of explosive events, with an accuracy on the order of 10 nanoseconds. The reliable telemetry of this data, from a high-speed missile trajectory, is a very challenging opportunity. All captured data must be transmitted in less than 20 microseconds of time duration. This requires a high bits/Hertz microwave telemetry modulation code to insure transmission of the data with the limited time interval available.

  8. Coupled explosive/structure computational techniques at Sandia National Laboratories

    SciTech Connect

    Preece, D.S.; Attaway, S.W.; Swegle, J.W.

    1997-06-01

    Simulation of the effects of explosives on structures is a challenge because the explosive response can best be simulated using Eulerian computational techniques and structural behavior is best modeled using Lagrangian methods. Due to the different methodology of the two computational techniques and code architecture requirements, they are usually implemented in different computer programs. Explosive and structure modeling in two different codes make it difficult or next to impossible to do coupled explosive/structure interaction simulations. Sandia National Laboratories has developed two techniques for solving this problem. The first is called Smoothed Particle Hydrodynamics (SPH), a relatively new gridless method comparable to Eulerian, that is especially suited for treating liquids and gases such as those produced by an explosive. The SPH capability has been fully implemented into the transient dynamics finite element (Lagrangian) codes PRONTO-2D and -3D. A PRONTO-3D/SPH simulation of the effect of a blast on a protective-wall barrier is presented in this paper. The second technique employed at Sandia uses a new code called Zapotec that combines the 3-D Eulerian code CTH and the Lagrangian code PRONTO-3D with minimal changes to either code. CTH and PRONTO-3D are currently executing on the Sandia Terraflops machine (9000 Pentium Pro processors). Eulerian simulations with 100 million cells have been completed on the current configuration of the machine (4500 Pentium Pro processors). The CTH and PRONTO-3D combination will soon be executing in a coupled fashion on this machine.

  9. On the Violence of High Explosive Reactions

    SciTech Connect

    Tarver, C M; Chidester, S K

    2004-02-09

    High explosive reactions can be caused by three general energy deposition processes: impact ignition by frictional and/or shear heating; bulk thermal heating; and shock compression. The violence of the subsequent reaction varies from benign slow combustion to catastrophic detonation of the entire charge. The degree of violence depends on many variables, including the rate of energy delivery, the physical and chemical properties of the explosive, and the strength of the confinement surrounding the explosive charge. The current state of experimental and computer modeling research on the violence of impact, thermal, and shock-induced reactions is reviewed.

  10. High explosives skid impact initiation study

    SciTech Connect

    Vigil, A.S.; Bunch, J.M.; Jaeger, D.L.; Smith, P.D.; Abeyta, E.E.

    1990-06-01

    The objective of this study was to develop a better quantitative understanding of explosive behavior under skid impact conditions. We evaluated the effects of sample weight, impact velocity, contact surface area at impact, target surface roughness, and target material on the skid impact HE ignition threshold. We also quantified the effects of two parameters that had never been fully investigated in the standard skid impact sensitivity test: explosive sample size and angle of incidence. These parameters were studied experimentally by conducting a series of tests, and analytical, with a number of one-, two-, and three-dimensional computer models. This study is the first phase in a program to measure the transient heat produced in the ignition of a high explosive sample as it impacts an infrared (IR) transmissive target. We will use the experimentally derived data to enhance our ability to predict the onset of ignition in impact-heated high explosives. 12 refs., 9 figs., 2 tabs.

  11. Ignition dynamics of high explosives

    SciTech Connect

    Ali, A.N.; Son, S.F.; Sander, R.K.; Asay, B.W.; Brewster, M.Q.

    1999-04-01

    The laser ignition of the explosives HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine, C{sub 4}H{sub 8}N{sub 8}O{sub 8}), {delta}-phase HMX, PBX 9501 (95% HMX, 2.5% Estane, 2.5% BDNPA/BDNPF), TATB (1,3,5-triamino-2,4,6-trinitrobenzene, C{sub 6}H{sub 6}N{sub 6}O{sub 6}), and PBX 9502 (95% TATB, 5% Kel-F) and aged PBX 9502 has been conducted with the intent to compare the relative sensitivities of those explosives and to investigate the effect of beam profile, binder addition, and porosity. It has been found that there was little difference between a gaussian beam and a top hat profile on the laser ignition of HMX. The authors observe that the addition of binder in the amounts present in PBX 9501 resulted in longer ignition delays than that of HMX. In contrast to HMX, the addition of binder to TATB in PBX 9502 shows no measurable effect. Porosity effects were considered by comparing the ignition of granular HMX and pressed HMX pellets. Porosity appears to increase ignition delay due to an increased effective absorption scale and increased convective heat loss. This porosity effect also resulted in longer ignition delays for {delta}-phase HMX than for {beta}-phase HMX. In order to simulate ignition in voids or cracks, the standard ignition experiment was modified to include a NaCl window placed at variable distances above the sample surface. When ignition experiments were performed at 29 W/cm{sup 2} and 38 W/cm{sup 2} a critical gap distance was observed of 6 {+-} 0.4 mm below which ignition was severely inhibited. This result underscores the importance of gas phase processes in ignition and illustrates that conditions can exist where simple ignition criteria such as surface temperature is inadequate.

  12. Explosive-driven, high speed, arcless switch

    DOEpatents

    Skogmo, P.J.; Tucker, T.J.

    1987-07-14

    An explosive-actuated, fast-acting arcless switch contains a highly conductive foil to carry high currents positioned adjacent a dielectric surface within a casing. At one side of the foil opposite the dielectric surface is an explosive which, when detonated, drives the conductive foil against the dielectric surface. A pattern of grooves in the dielectric surface ruptures the foil to establish a rupture path having a pattern corresponding to the pattern of the grooves. The impedance of the ruptured foil is greater than that of the original foil to divert high current to a load. Planar and cylindrical embodiments of the switch are disclosed. 7 figs.

  13. Explosive-driven, high speed, arcless switch

    DOEpatents

    Skogmo, P.J.; Tucker, T.J.

    1986-05-02

    An explosive-actuated, fast-acting arcless switch contains a highly conductive foil to carry high currents positioned adjacent a dielectric surface within a casing. At one side of the foil opposite the dielectric surface is an explosive which, when detonated, drives the conductive foil against the dielectric surface. A pattern of grooves in the dielectric surface ruptures the foil to establish a rupture path having a pattern corresponding to the pattern of the grooves. The impedance of the ruptured foil is greater than that of the original foil to divert high current to a load. Planar and cylindrical embodiments of the switch are disclosed.

  14. Explosive-driven, high speed, arcless switch

    DOEpatents

    Skogmo, Phillip J.; Tucker, Tillman J.

    1987-01-01

    An explosive-actuated, fast-acting arcless switch contains a highly conductive foil to carry high currents positioned adjacent a dielectric surface within a casing. At one side of the foil opposite the dielectric surface is an explosive which, when detonated, drives the conductive foil against the dielectric surface. A pattern of grooves in the dielectric surface ruptures the foil to establish a rupture path having a pattern corresponding to the pattern of the grooves. The impedance of the ruptured foil is greater than that of the original foil to divert high current to a load. Planar and cylindrical embodiments of the switch are disclosed.

  15. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2009-12-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  16. Study on metal foil explosion using high current

    NASA Astrophysics Data System (ADS)

    Mihara, Takayuki; Matsuo, N.; Otsuka, M.; Itoh, S.

    2010-03-01

    In the high energy processing using explosive, there are variety of application examples which is explosion welding of differential metallic plate and powder compaction of diamond. However a rule legal to explosives is severe and needs many efforts for handling qualification acquisition, maintenance, and security. In this research, the metallic foil explosion using high current is paid my attention to the method to obtain linear or planate explosive initiation easily, and the main evaluation of metallic foil explosion was conducted. The explosion power was evaluated by observing optically the underwater shock wave generated from the metallic foil explosion.

  17. Equation of state of insensitive high explosives

    SciTech Connect

    Ree, F H; Van Thiel, M; Viecelli, J A

    1998-08-12

    Detonation of an insensitive high explosive formulated with a fluorine containing binder produces a large amount of condensed carbon and gaseous HF product, which transforms into CF{sub 4} as the pressure is increased. The former (carbon condensation) is characterized by slow energy release, while the latter (HF) has no shockwave data. We have identified that these two items are the key factors, which make reliable prediction of the performance of an insensitive high explosive very difficult. This paper describes physical models to address these issues and apply the models to analyze experimental data of LX-17.

  18. Criticality safety in high explosives dissolution

    SciTech Connect

    Troyer, S.D.

    1997-06-01

    In 1992, an incident occurred at the Pantex Plant in which the cladding around a fissile material component (pit) cracked during dismantlement of the high explosives portion of a nuclear weapon. Although the event did not result in any significant contamination or personnel exposures, concerns about the incident led to the conclusion that the current dismantlement process was unacceptable. Options considered for redesign, dissolution tooling design considerations, dissolution tooling design features, and the analysis of the new dissolution tooling are summarized. The final tooling design developed incorporated a number of safety features and provides a simple, self-contained, low-maintenance method of high explosives removal for nuclear explosive dismantlement. Analyses demonstrate that the tooling design will remain subcritical under normal, abnormal, and credible accident scenarios. 1 fig.

  19. A basic test method for the study of explosion treatment of waste chemicals from laboratories.

    PubMed

    Li, H; Arai, M; Tamura, M; Matsunaga, T; Iida, M

    1999-10-29

    As a part of the research on the explosion treatment of waste chemicals from laboratories, a basic test method, which will provide the basis for our future research, was developed. First, the basic explosive, the scale of the explosion chamber and the assembly of the sample were decided. Then, measurement of detonation velocity was carried out, and the relationship between the quantity of explosive and the state of detonation propagation was obtained. A quantitative method for evaluating the decomposability of organic chemicals under explosion treatment was investigated. The results indicate that evaluating the explosion decomposability of organic chemicals from the gasification ratio could be used as a basic method provided that the excessive oxygen is approximately 62 mol% or higher. Finally, examinations of the possible effects of the quantity of explosive and conditions of atmosphere on the explosion decomposition of the model substance were conducted, and the basic test conditions regarding the quantity of explosive and condition of atmosphere were decided.

  20. Internal Detonation Velocity Measurements Inside High Explosives

    SciTech Connect

    Benterou, J; Bennett, C V; Cole, G; Hare, D E; May, C; Udd, E

    2009-01-16

    In order to fully calibrate hydrocodes and dynamic chemistry burn models, initiation models and detonation models of high explosives, the ability to continuously measure the detonation velocity within an explosive is required. Progress on an embedded velocity diagnostic using a 125 micron diameter optical fiber containing a chirped fiber Bragg grating is reported. As the chirped fiber Bragg grating is consumed by the moving detonation wave, the physical length of the unconsumed Bragg grating is monitored with a fast InGaAs photodiode. Experimental details of the associated equipment and data in the form of continuous detonation velocity records within PBX-9502 are presented. This small diameter fiber sensor has the potential to measure internal detonation velocities on the order of 10 mm/{micro}sec along path lengths tens of millimeters long.

  1. High pressure-resistant nonincendive emulsion explosive

    DOEpatents

    Ruhe, Thomas C.; Rao, Pilaka P.

    1994-01-01

    An improved emulsion explosive composition including hollow microspheres/bulking agents having high density and high strength. The hollow microspheres/bulking agents have true particle densities of about 0.2 grams per cubic centimeter or greater and include glass, siliceous, ceramic and synthetic resin microspheres, expanded minerals, and mixtures thereof. The preferred weight percentage of hollow microspheres/bulking agents in the composition ranges from 3.0 to 10.0 A chlorinated paraffin oil, also present in the improved emulsion explosive composition, imparts a higher film strength to the oil phase in the emulsion. The emulsion is rendered nonincendive by the production of sodium chloride in situ via the decomposition of sodium nitrate, a chlorinated paraffin oil, and sodium perchlorate. The air-gap sensitivity is improved by the in situ formation of monomethylamine perchlorate from dissolved monomethylamine nitrate and sodium perchlorate. The emulsion explosive composition can withstand static pressures to 139 bars and dynamic pressure loads on the order of 567 bars.

  2. Model testing of a 1-kg high-explosive-cell maze

    SciTech Connect

    Bacigalupi, C.M.; Burton, W.A.

    1981-04-01

    The basement of the proposed High Explosives Applications Facility (Building 353) at the Lawrence Livermore National Laboratory includes several explosive test cells for the assembly and/or storage of up to 10 kg of high explosive (HE). This document reports 1/8-scale and 1/4-scale model tests conducted to confirm maze design criteria, to determine the cell explosive weight limit based on an allowable 10 psi reflected shock pressure at the hallway-maze doorway, and to specify permissible areas for handling HE within the cell. The integrity of cube-root scaling of the explosive charges detonated in the 1/8-scale model was verified by explosive testing in a comparable 1/4-scale model. Reflected shock pressures in the hallway adjacent to the maze and the effect of HE charge orientation were investigated and are also reported.

  3. Characterization Of High Explosives Detonations Via Laser-Induced Plasmas

    SciTech Connect

    Villa-Aleman, E.

    2015-10-08

    One objective of the Department of Energy’s National Security Administration is to develop technologies that can help the United States government to detect foreign nuclear weapons development activities. The realm of high explosive (HE) experiments is one of the key areas to assess the nuclear ambitions of a country. SRNL has participated in the collection of particulates from HE experiments and characterized the material with the purpose to correlate particulate matter with HE. Since these field campaigns are expensive, on-demand simulated laboratory-scale explosion experiments are needed to further our knowledge of the chemistry and particle formation in the process. Our goal is to develop an experimental test bed in the laboratory to test measurement concepts and correlate particle formation processes with the observables from the detonation fireball. The final objective is to use this knowledge to tailor our experimental setups in future field campaigns. The test bed uses pulsed laser-induced plasmas to simulate micro-explosions, with the intent to study the temporal behavior of the fireball observed in field tests. During FY15, a plan was prepared and executed which assembled two laser ablation systems, procured materials for study, and tested a Step-Scan Fourier Transform Infrared Spectrometer (SS-FTIR). Designs for a shadowgraph system for shock wave analysis, design for a micro-particulate collector from ablated pulse were accomplished. A novel spectroscopic system was conceived and a prototype system built for acquisition of spectral/temporal characterization of a high speed event such as from a high explosive detonation. Experiments and analyses will continue into FY16.

  4. Vibrational energy transfer in high explosives: Nitromethane

    SciTech Connect

    Hong, X.; Hill, J.R.; Dlott, D.D.

    1996-03-01

    Time resolved vibrational spectroscopy with picosecond tunable mid-infrared pulses is used to measure the rates and investigate the detailed mechanisms of multiphonon up-pumping and vibrational cooling in a condensed high explosive, nitromethane. Both processes occur on the 100 ps time scale under ambient conditions. The mechanisms involve sequential climbing or descending the ladder of molecular vibrations. Efficient intermolecular vibrational energy transfer from various molecules to the symmetric stretching excitation of NO2 is observed. The implications of these measurements for understanding shock initiation to detonation and the sensitivities of energetic materials to shock initiation are discussed briefly.

  5. Three Decades of Explosive High Energy Transients

    NASA Technical Reports Server (NTRS)

    Kouveliotou, Chryssa

    2013-01-01

    Gamma-Ray Bursts are the most brilliant explosions in space. The first GRB was discovered on 1967, just 40 years ago. It took several years and multiple generations of space and ground instruments to unravel some of the mysteries of this phenomenon. However, many questions remain open today. I will discuss the history, evolution and current status of the GRB field and its contributions in our understanding of the transient high energy sky. Finally, I will describe how GRBs can be utilized in future missions as tools, to probe the cosmic chemical evolution of the Universe and the star formation rates.

  6. High explosive violent reaction (HEVR) from slow heating conditions

    SciTech Connect

    Vigil, A.S.

    1999-03-01

    The high explosives (HEs) developed and used at the Los Alamos National Laboratory are designed to be insensitive to impact and thermal insults under all but the most extreme conditions. Nevertheless, violent reactions do occasionally occur when HE is involved in an accident. The HE response is closely dependent on the type of external stimulus that initiates the reaction. For example, fast heating of conventional HE will probably result in fairly benign burning, while long-term, slow heating of conventional HE is more likely to produce an HEVR that will do much more damage to the immediate surroundings. An HEVR (High Explosive Violent Reaction) can be defined as the rapid release of energy from an explosive that ranges from slightly faster than a deflagration (very rapid burning) to a reaction that approaches a detonation. A number of thermal analyses have been done to determine slow heat/cook-off conditions that produce HE self-heating that can build up to a catastrophic runaway reaction. The author specifies the conditions that control reaction violence, describes experiments that produced an HEVR, describes analyses done to determine a heating rate threshold for HEVR, and lists possible HEVR situations.

  7. Dynamics of Strombolian explosions: Inferences from field and laboratory studies of erupted bombs from Stromboli volcano

    NASA Astrophysics Data System (ADS)

    Gurioli, L.; Colo', L.; Bollasina, A. J.; Harris, A. J. L.; Whittington, A.; Ripepe, M.

    2014-01-01

    Strombolian activity is characterized by repeated, low energy, explosions and is named after the volcano where such activity has persisted for around 2000 years, i.e., Stromboli (Aeolian Islands, Italy). Stromboli represents an excellent laboratory where measurements of such explosions can be made from safe, but close, distances. During a field campaign in 2008, two 15 cm diameter bombs were quenched and collected shortly after a normal explosion. The bombs were characterized in terms of their textural, chemical, rheological, and geophysical signatures. The vesicle and crystal size distribution of the samples, coupled with the glass chemistry, enabled us to quantify variations in the degassing history and rheology of the magma resident in the shallow (i.e., in last 250 m of conduit length). The different textural facies observed in these bombs showed that fresh magma was mingled with batches of partially to completely degassed, oxidized, high-crystallinity, high-viscosity, evolved magma. This magma sat at the top of the conduit and played only a passive role in the explosive process. The fresh, microlite-poor, vesiculated batch, however, experienced a response to the explosive event, by undergoing rapid decompression. Integration of geophysical measurements with sample analyses indicates that popular bubble-bursting models may not fit this case. We suggest that the degassed, magma forms a plug, or rheological layer, at the top of the conduit, through which the fresh magma bursts. In this model we need to consider the paradox of a slug ascending too fast through a magma of varying viscosity and yield strength.

  8. Multistage reaction pathways in detonating high explosives

    SciTech Connect

    Li, Ying; Kalia, Rajiv K.; Nakano, Aiichiro; Nomura, Ken-ichi; Vashishta, Priya

    2014-11-17

    Atomistic mechanisms underlying the reaction time and intermediate reaction products of detonating high explosives far from equilibrium have been elusive. This is because detonation is one of the hardest multiscale physics problems, in which diverse length and time scales play important roles. Here, large spatiotemporal-scale reactive molecular dynamics simulations validated by quantum molecular dynamics simulations reveal a two-stage reaction mechanism during the detonation of cyclotrimethylenetrinitramine crystal. Rapid production of N{sub 2} and H{sub 2}O within ∼10 ps is followed by delayed production of CO molecules beyond ns. We found that further decomposition towards the final products is inhibited by the formation of large metastable carbon- and oxygen-rich clusters with fractal geometry. In addition, we found distinct unimolecular and intermolecular reaction pathways, respectively, for the rapid N{sub 2} and H{sub 2}O productions.

  9. Mesoscale modeling of metal-loaded high explosives

    SciTech Connect

    Bdzil, John Bohdan; Lieberthal, Brandon; Srewart, Donald S

    2010-01-01

    We describe a 3D approach to modeling multi-phase blast explosive, which is primarily condensed explosive by volume with inert embedded particles. These embedded particles are uniform in size and placed on the array of a regular lattice. The asymptotic theory of detonation shock dynamics governs the detonation shock propagation in the explosive. Mesoscale hydrodynamic simulations are used to show how the particles are compressed, deformed, and accelerated by the high-speed detonation products flow.

  10. Equation of state of unreacted high explosives at high pressures

    SciTech Connect

    Yoo, C-S

    1998-08-14

    Isotherms of unreacted high explosives (HMX, RDX, and PETN) have been determined to quasi-hydrostatic high pressures below 45 GPa, by using a diamond-anvil cell angle-resolved synchrotron x-ray diffraction method. The equation-of-state parameters (bulk modulus Bo, and its derivatives B' ) are presented for the 3rd-order Birch-Murnaghan formula based on the measured isotherms. The results are also used to retrieve unreacted Hugoniots in these high explosives and to develop the equations of state and kinetic models for composite high explolsivcs such as XTX-8003 and LX-04. The evidence of shear-induced chemistry of HMX in non-hydrostatic conditions is also presented.

  11. Energetic nanocomposites for detonation initiation in high explosives without primary explosives

    NASA Astrophysics Data System (ADS)

    Comet, Marc; Martin, Cédric; Klaumünzer, Martin; Schnell, Fabien; Spitzer, Denis

    2015-12-01

    The mixing of aluminum nanoparticles with a metal containing oxidizer (here, WO3 or Bi2(SO4)3) gives reactive materials called nanothermites. In this research, nanothermites were combined with high explosive nanoparticles (RDX) to prepare energetic nanocomposites. These smart nanomaterials have higher performances and are much less hazardous than primary explosives. Their flame propagation velocity can be tuned from 0.2 to 3.5 km/s, through their explosive content. They were used to initiate the detonation of a high explosive, the pentaerythritol tetranitrate. The pyrotechnic transduction of combustion into detonation was achieved with short length systems (<2 cm) and small amounts of energetic nanocomposites (˜100 mg) in semi-confined systems.

  12. A second survey of high explosives traces in public places.

    PubMed

    Cullum, Hazel E; McGavigan, Claire; Uttley, Claire Z; Stroud, Mark A M; Warren, Derek C

    2004-07-01

    This survey was carried out as a follow-up to a 1994 survey carried out by this laboratory (1) in order to determine the background levels of explosives traces in public places. The first survey concentrated on transport areas and police stations in and around London. This second study examines levels in four of the United Kingdom's major cities: Birmingham, Cardiff, Glasgow, and Manchester. Samples were taken at various transport sites and from hotels, private houses, private vehicles, and clothing. The survey showed that traces of the high explosives nitroglycerine (NG), trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN), and cyclotrimethylene trinitramine (RDX) are rare within the general public environment. Only one low-level trace of RDX was detected. NG, possibly associated with the use of firearms, was detected at low levels in two samples and 2,4-DNT was detected in a separate sample. No PETN was detected in any of the samples. The results of the survey indicate that it is unlikely that persons visiting public areas could become significantly contaminated with explosives. The analytical procedures employed would also have detected ethylene glycol dinitrate (EGDN) if present at levels greater than 2 ng, nitrobenzene (NB) if present at levels greater than 50 ng, mononitrotoluenes if present at levels greater than 50 ng, and the other common isomers of dinitrotoluene if these had been present at levels in excess of 10 ng. None of these were detected. The relatively high volatility of EGDN, NB, and the mononitrotoluenes would, however, cause traces of these compounds to disperse rapidly. A proportion of the samples (approximately 7%) were analyzed for the presence of HMX. No HMX was detected. PMID:15317181

  13. Turbulent mixing in high-altitude explosions

    SciTech Connect

    Kuhl, A.L.; Bell, J.B. ); Ferguson, R.E. ); White, W.W.; McCartor, T.H. )

    1992-09-01

    Numerical simulations of a high-altitude explosion were performed using a Godunov code with Adaptive Mesh Refinement (AMR). The code solves the two-dimensional (2-D), time-dependent conservation laws of inviscid gas dynamics while AMR is used to focus the computational effort in the mixing regions. The calculations revealed that a spherical density interface embedded in this flow was unstable and rolled up into a turbulent mixing layer. The shape of the interface was qualitatively similar to experimental photographs. Initially, the mixing layer width grew as a linear function of time, but eventually it reached an asymptotically-constant value. The flow field was azimuthally-averaged to evaluate the mean-flow profiles and the R.M.S. fluctuation profiles across the mixing layer. The mean kinetic energy rapidly approached zero as the blast wave decayed, but the fluctuating kinetic energy asymptotically approached a small constant value (a fraction of a percent of the maximum kinetic energy). This represents the rotational kinetic energy driven by the vorticity field, that continued to mix the fluid indefinitely. It was shown that the vorticity field corresponds to a function that fluctuates between plus and minus values -- with a volume-averaged mean of zero. The amplitude of the vorticity fluctuations decayed as t[sup [minus]1]. The corresponding enstrophy increased linearly with time because of a cascade process for the mean-squared vorticity. This result is in good agreement with the 2-D calculations of turbulent flow as reported by G.K. Batchelor. The problem should be recalculated in 3-D to study the decay of turbulent mixing for spherical interfaces.

  14. Turbulent mixing in high-altitude explosions

    SciTech Connect

    Kuhl, A.L.; Bell, J.B.; Ferguson, R.E.; White, W.W.; McCartor, T.H.

    1992-09-01

    Numerical simulations of a high-altitude explosion were performed using a Godunov code with Adaptive Mesh Refinement (AMR). The code solves the two-dimensional (2-D), time-dependent conservation laws of inviscid gas dynamics while AMR is used to focus the computational effort in the mixing regions. The calculations revealed that a spherical density interface embedded in this flow was unstable and rolled up into a turbulent mixing layer. The shape of the interface was qualitatively similar to experimental photographs. Initially, the mixing layer width grew as a linear function of time, but eventually it reached an asymptotically-constant value. The flow field was azimuthally-averaged to evaluate the mean-flow profiles and the R.M.S. fluctuation profiles across the mixing layer. The mean kinetic energy rapidly approached zero as the blast wave decayed, but the fluctuating kinetic energy asymptotically approached a small constant value (a fraction of a percent of the maximum kinetic energy). This represents the rotational kinetic energy driven by the vorticity field, that continued to mix the fluid indefinitely. It was shown that the vorticity field corresponds to a function that fluctuates between plus and minus values -- with a volume-averaged mean of zero. The amplitude of the vorticity fluctuations decayed as t{sup {minus}1}. The corresponding enstrophy increased linearly with time because of a cascade process for the mean-squared vorticity. This result is in good agreement with the 2-D calculations of turbulent flow as reported by G.K. Batchelor. The problem should be recalculated in 3-D to study the decay of turbulent mixing for spherical interfaces.

  15. High Resolution Laboratory Spectroscopy

    NASA Astrophysics Data System (ADS)

    Brünken, S.; Schlemmer, S.

    2016-05-01

    In this short review we will highlight some of the recent advancements in the field of high-resolution laboratory spectroscopy that meet the needs dictated by the advent of highly sensitive and broadband telescopes like ALMA and SOFIA. Among these is the development of broadband techniques for the study of complex organic molecules, like fast scanning conventional absorption spectroscopy based on multiplier chains, chirped pulse instrumentation, or the use of synchrotron facilities. Of similar importance is the extension of the accessible frequency range to THz frequencies, where many light hydrides have their ground state rotational transitions. Another key experimental challenge is the production of sufficiently high number densities of refractory and transient species in the laboratory, where discharges have proven to be efficient sources that can also be coupled to molecular jets. For ionic molecular species sensitive action spectroscopic schemes have recently been developed to overcome some of the limitations of conventional absorption spectroscopy. Throughout this review examples demonstrating the strong interplay between laboratory and observational studies will be given.

  16. On the Initiation of High Explosives by Laser Radiation

    SciTech Connect

    Rubenchik, A M

    2006-03-28

    The problem of laser initiation of high explosives in munitions is considered. In this situation, the laser illuminates a small spot on the casing, and lateral thermal transport affects the initiation temperature. We use a variational method to calculate the critical temperature for explosive initiation as a function the laser spot size, for common high explosives. The effect of the dwelling time of the irradiation is then evaluated. We demonstrate that in typical situations the critical temperature is determined by the dwelling time rather than by the laser spot size.

  17. Gamma rays and supernova explosions. [high temperature radiation measurement

    NASA Technical Reports Server (NTRS)

    Arnett, W. D.

    1977-01-01

    Thermal radiation associated with the explosion of supernovae is investigated. High temperature is required to produce copious gamma radiation of this sort. It appears that type 11 supernovae do not release much of their energy as gamma ray continuum radiation.

  18. Flying-plate detonator using a high-density high explosive

    DOEpatents

    Stroud, John R.; Ornellas, Donald L.

    1988-01-01

    A flying-plate detonator containing a high-density high explosive such as benzotrifuroxan (BTF). The detonator involves the electrical explosion of a thin metal foil which punches out a flyer from a layer overlying the foil, and the flyer striking a high-density explosive pellet of BTF, which is more thermally stable than the conventional detonator using pentaerythritol tetranitrate (PETN).

  19. Method for enhancing stability of high explosives, for purposes of transport or storage, and the stabilized high explosives

    DOEpatents

    Nutt, Gerald L.

    1991-01-01

    The stability of porous solid high explosives, for purposes of transport or storage, is enhanced by reducing the sensitivity to shock initiation of a reaction that leads to detonation. The pores of the explosive down to a certain size are filled under pressure with a stable, low melt temperature material in liquid form, and the combined material is cooled so the pore filling material solidifies. The stability can be increased to progressively higher levels by filling smaller pores. The pore filling material can be removed, at least partially, by reheating above its melt temperature and drained off so that the explosive is once more suitable for detonation.

  20. Design of a hypersonic waterjet apparatus driven by high explosives

    SciTech Connect

    Weeks, Brandon L.; Klosterman, John; Worsey, Paul N.

    2001-08-01

    The design and construction of a hypersonic waterjet apparatus is described. Jet velocities from 0.5 to 5 km/s have been achieved using a high explosive charge. Images are obtained in situ on various target substrates using a high-speed framing camera. Experimental results are shown for the impact of high velocity waterjets on propellants and high explosive samples. By observing the impact of the waterjet at a wide range of velocities a safety threshold can be determined where no reaction takes place.

  1. An Orientation to Explosive Safety.

    ERIC Educational Resources Information Center

    Harris, Betty W.

    1987-01-01

    Provides an overview of various types of explosives. Classifies and describes explosives as initiating or primary explosives, low explosives, and high (secondary explosives). Discusses detonating devices, domestic explosive systems, the sensitivity of explosives, explosive reactions, and emergency responses. (TW)

  2. High-explosive-driven delay line pulse generator

    SciTech Connect

    Shearer, J.W.

    1982-11-15

    The inclusion of a delay line circuit into the design of a high-explosive-driven generator shortens the time constant of the output pulse. After a brief review of generator concepts and previously described pulse-shortening methods, a geometry is presented which incorporates delay line circuit techcniques into a coil generator. The circuit constants are adjusted to match the velocity of the generated electromagnetic wave to the detonation velocity of the high explosive. The proposed generator can be modeled by adding a variable inductance term to the telegrapher's equation. A particular solution of this equation is useful for exploring the operational parameters of the generator. The duration of the electromagnetic pulse equals the radial expansion time of the high-explosive-driven armature until it strikes the coil. Because the impedance of the generator is a constant, the current multiplication factor is limited only by nonlinear effects such as voltage breakdown, diffusion, and compression at high energies.

  3. High-Yield Magnetized Liner Fusion Explosions and Blast Mitigation

    NASA Astrophysics Data System (ADS)

    Slutz, Stephen; Vesey, Roger; Cuneo, Michael

    2011-10-01

    Cylindrical liner implosions with preheated and magnetized deuterium-tritium (DT) are predicted to reach fusion conditions on present pulsed power machines [S.A. Slutz et al Phys. Plasmas 17, 056303 (2010)]. We present simulations indicating that high yields (1-10 GJ) and gains (100-1000) may be possible at currents of about 60-70 MA if a cryogenic layer of solid DT is provided on the inside surface of the metal liner. A hot spot is formed from the central preheated magnetized low-density gas and a burn wave propagates radially into the surrounding cold dense fuel. These yields and gains are more than adequate for inertial fusion energy. However, the pulsed-power driver must be protected from the blast of these high-yield explosions. Numerical simulations are presented which show that the blast can be deflected and the fusion neutrons absorbed by a blanket that partially surrounds the liner. Thus a modest length transmission line can be used to deliver power to the liner. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  4. Explosive Components Facility at Sandia National Laboratories, Albuquerque, New Mexico. Environmental assessment

    SciTech Connect

    Not Available

    1992-07-01

    The United States Department of Energy (DOE) has prepared an environmental assessment (EA) on the proposed Explosive Components Facility (ECF) at the Sandia National Laboratories, Albuquerque (SNL). This facility is needed to integrate, centralize, and enhance many of the explosive, neutron generation, and weapons testing programs currently in progress at SNL. In general, there is insufficient space in existing facilities for the development and testing activities required by modern explosives technologies. The EA examined the potential environmental impacts of the proposed ECF project and discussed potential alternatives. Based on the analyses in the EA, DOE has determined that the proposed action does not constitute a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969, and CEQ regulations at 40 CFR 1508.18 and 1508.27. Therefore, an environmental impact statement (EIS) is not required, and the DOE is issuing this Finding of No Significant Impact (FONSI).

  5. Tool force evaluation of lathe machined high explosives

    SciTech Connect

    Flowers, G.L.

    1980-04-01

    The purpose of this study was to develop a better understanding of the effects of machining properties upon tool forces encountered during lathe machining of high explosives, in order to optimize machining conditions for mechanical properties test specimens. Monetary considerations dictated that the tooling either already exist or be fabricated in-house using limited machine shop capability. The design chosen which fit between the tool holder and the tool post and interfaced to existing signal conditioners was easily fabricated. The study evaluated all forces on the cutter during machining of two types of high explosives at four cutter radii, four feed rates, three depths of cut and two cutting speeds. The study pointed out design problems, instrumentation drift, tool chatter and detection levels. It also showed that the type of high explosive was more significant than first thought toward influencing tool force levels.

  6. High-performance, extrusion-cast explosives with low sensitivity: Interim report No. 2

    SciTech Connect

    Scribner, K.J.; von Holtz, E.; Simpson, R.L.

    1989-01-10

    Lawrence Livermore National Laboratory (LLNL) has developed a class of explosives having both high performance for modern precision munitions and greater safety for reduced vulnerability of launch platforms (ships, planes, ammunition storage sites) to enemy fire or accidents. Known as extrusion-cast explosives (ECXs), they have demonstrated performance levels equivalent to the most powerful now available, but test results indicate they are far less sensitive than the conventional high-energy explosives. Specifically, in a sympathetic-detonation test, ECX that was immediately adjacent to a deliberately-detonated donor charge did not detonate in two of three tests, whereas Comp B did detonate sympathetically in this test. Also, this ECX provided performance equivalent to that of the high-performance explosive LX-14, when tested in the TOW (tube-launched, optically-sighted, wire-guided) missile. This report describes the performance, vulnerability, and processing (at this stage of development) of this class of explosives. 9 refs., 18 figs., 11 tabs.

  7. Mechanisms of formation of trace decomposition products in complex high explosive mixtures

    SciTech Connect

    Woodyard, J.D.; Burgess, C.E.; Rainwater, K.A.

    1999-03-01

    A significant concern in the nation`s stockpile surveillance program in prediction of the lifetimes of the high explosives (HE) and their components as the weapons age. The Department of Energy`s Core Surveillance and Enhanced Surveillance programs specifically target issues of degradation of HE, binders, and plastic-bonded explosives (PBX) for determination of component lifetimes and handling procedures. These material science topics are being addressed at the DOE national laboratories and production plants, including Pantex. The principal goal of this project is to identify the mechanisms of decomposition of HE, plasticizers, plastic polymer binders, and radical stabilizers resulting from exposures to ionizing radiation, heat, and humidity. The following reports the work completed for 1998, including a comprehensive literature review about some of the materials examined and the laboratory work completed to date. The materials focused on in the laboratory are TATB, Estane 5301, and Irganox 1010.

  8. Equations of State and High-Pressure Phases of Explosives

    NASA Astrophysics Data System (ADS)

    Peiris, Suhithi M.; Gump, Jared C.

    Energetic materials, being the collective name for explosives, propellants, pyrotechnics, and other flash-bang materials, span a wide range of composite chemical formulations. Most militarily used energetics are solids composed of particles of the pure energetic material held together by a binder. Commonly used binders include various oils, waxes, and polymers or plasticizers, and the composite is melt cast, cured, or pressed to achieve the necessary mechanical properties (gels, putties, sheets, solid blocks, etc.) of the final energetic material. Mining, demolition, and other industries use liquid energetics that are similarly composed of an actual energetic material or oxidizer together with a fuel, that is to be mixed and poured for detonation. Pure energetic materials that are commonly used are nitroglycerine, ammonium nitrate, ammonium or sodium perchlorate, trinitrotoluene (TNT), HMX, RDX, and TATB. All of them are molecular materials or molecular ions that when initiated or insulted undergoes rapid decomposition with excessive liberation of heat resulting in the formation of stable final products. When the final products are gases, and they are rapidly produced, the sudden pressure increase creates a shock wave. When decomposition is so rapid that the reaction moves through the explosive faster than the speed of sound in the unreacted explosive, the material is said to detonate. Typically, energetic materials that undergo detonation are known as high explosives (HEs) and energetic materials that burn rapidly or deflagrate are known as low explosives and/or propellants.

  9. Sensitivity of once-shocked, weathered high explosives

    SciTech Connect

    Williams, K.L.; Harris, B.W.

    1998-07-01

    Effects caused by stimulating once-shocked, weathered high explosives (OSW-HE) are investigated. The sensitivity of OSW-HE to mechanical stimuli was determined using standard industry tests. Some initial results are given. Pieces of OSW-HE were collected from active and inactive firing sites and from an area surrounding a drop tower at Los Alamos where skid and spigot tests were done. Samples evaluated were cast explosives or plastic bonded explosive (PBX) formulations containing cyclotrimethylenetrinitramine (RDX), cyclotetramethylene tetranitramine (HMX), 2,4,6-trinitrotoluene (TNT), mock or inert HE [tris(beta-chloroethyl)phosphate (CEF)], barium nitrate, cyanuric acid, talc, and Kel-F. Once-shocked, weathered LX-10 Livermore explosive [HMX/Viton A, (95/5 wt %)], PBX 9011 [HMX/Estane, (90/10 wt %)], PBX 9404 [HMX/nitrocellulose, tris(beta-chloroethyl) phosphate, (94/3/3 wt %)], Composition B or cyclotol (TNT/RDX explosives), and PBX 9007 (90% RDX, 9.1% styrene, 0.5% dioctyl phthalate, and 0.45 resin) were subjected to the hammer test, the drop-weight impact sensitivity test, differential thermal analysis (DTA), the spark test, the Henkin`s critical temperature test, and the flame test. Samples were subjected to remote, wet cutting and drilling; remote, liquid-nitrogen-cooled grinding and crushing; and scanning electron microscope (SEM) surface analyses for morphological changes.

  10. High-frequency P wave spectra from explosions and earthquakes

    NASA Astrophysics Data System (ADS)

    Walter, William R.; Priestley, Keith F.

    Two explosion P wave spectral models [Sharpe, 1942; Mueller-Murphy, 1971] and two earthquake P wave spectral models [Archambeau, 1968, 1972; modified Brune 1970, 1971] are reviewed to assess their implications for high-frequency (>1 Hz) seismic discrimination between earthquakes and explosions. The importance of the corner frequency scaling, particularly for models with the same high-frequency spectral decay rate, is demonstrated by calculating source spectral ratios (a potentially important regional discriminant) for these models. We compare North American events and a limited data set of Central Asian events with these spectral models. We find North American earthquakes are consistent with a constant stress drop modified Brune model between 10 and 30 Hz. Shallow (<700 m depth) Pahute Mesa explosions at the Nevada Test Site have a high-frequency spectral decay between 10 and 30 Hz greater than the ω-2 predicted by the explosion models. Near regional recordings of the Soviet Joint Verification Experiment (JVE) explosion show a higher corner frequency and lower 1 to 4 Hz spectral ratios than predicted by either explosion model. The higher corner frequency of the Soviet JVE appears not to be due to attenuation, or receiver effects, and may represent a need for different corner frequency scaling, or result from source complications such as spall and tectonic release. A regional recording of the Soviet JVE (NEIC mb = 6.1) is shown to have a lower 1 to 4 Hz spectral ratio than a smaller earthquake (NEIC mb = 4.6) recorded on a nearly reciprocal path.

  11. High Explosive Deonation Threshold Sensitivity Due to Multiple Fragment Impacts

    SciTech Connect

    Georgevich, V; Pincosy, P; Chase, J

    2004-01-07

    Fragments, bullets or projectiles can initiate a detonation in a high explosive (HE). For this to happen certain critical conditions need to be exceeded. For a given explosive, these critical conditions are the projectile velocity, the projectile size and shape, and the projectile material properties. A lot of work has been done in the area of metal shaped charge jets and individual fragments impacting the HE. One major gap in understanding initiation phenomena is the effect of multiple fragment impact. This study shows that multiple fragments can lower the fragment size and the kinetic energy thresholds.

  12. Nuclear explosive safety study process

    SciTech Connect

    1997-01-01

    Nuclear explosives by their design and intended use require collocation of high explosives and fissile material. The design agencies are responsible for designing safety into the nuclear explosive and processes involving the nuclear explosive. The methodology for ensuring safety consists of independent review processes that include the national laboratories, Operations Offices, Headquarters, and responsible Area Offices and operating contractors with expertise in nuclear explosive safety. A NES Study is an evaluation of the adequacy of positive measures to minimize the possibility of an inadvertent or deliberate unauthorized nuclear detonation, high explosive detonation or deflagration, fire, or fissile material dispersal from the pit. The Nuclear Explosive Safety Study Group (NESSG) evaluates nuclear explosive operations against the Nuclear Explosive Safety Standards specified in DOE O 452.2 using systematic evaluation techniques. These Safety Standards must be satisfied for nuclear explosive operations.

  13. High and low velocity detonation in a highly insensitive explosive

    NASA Astrophysics Data System (ADS)

    Sandusky, H. W.; Hayden, H. F.

    2014-05-01

    Low-velocity detonation (LVD) in a solid explosive from input shocks below the threshold for high-velocity detonation (HVD) had been previously reported for PBXN-109 in two gap tests with sample diameters of 36.5 and 73.0 mm. Similar phenomenon has now been observed for the highly insensitive PBXIH-140, whose critical diameter of ~100 mm required an even larger gap test with a sample diameter of 178 mm. When just exceeding the critical gap for HVD, LVD propagated at similar velocities as in PBXN-109 and would punch clean holes in a witness plate like HVD. For somewhat greater gaps, there was enough shock reaction to drive LVD at constant but reduced velocities as the input shock decreased to ~ ½ of critical. With a different formulation now exhibiting LVD, it may be more prevalent than previously realized. It is speculated to occur in various confinements when small percentages of easily detonable ingredients fail to initiate the remainder of less shock sensitive ingredients.

  14. Subnanosecond measurements of detonation fronts in solid high explosives

    NASA Astrophysics Data System (ADS)

    Sheffield, S. A.; Bloomquist, D. D.; Tarver, C. M.

    1984-04-01

    Detonation fronts in solid high explosives have been examined through measurements of particle velocity histories resulting from the interaction of a detonation wave with a thin metal foil backed by a water window. Using a high time resolution velocity-interferometer system, experiments were conducted on three explosives—a TATB (1,3,5-triamino-trinitrobenzene)-based explosive called PBX-9502, TNT (2,4,6-Trinitrotoluene), and CP (2-{5-cyanotetrazolato} pentaamminecobalt {III} perchlorate). In all cases, detonation-front rise times were found to be less than the 300 ps resolution of the interferometer system. The thermodynamic state in the front of the detonation wave was estimated to be near the unreacted state determined from an extrapolation of low-pressure unreacted Hugoniot data for both TNT and PBX-9502 explosives. Computer calculations based on an ignition and growth model of a Zeldovich-von Neumann-Doering (ZND) detonation wave show good agreement with the measurements. By using the unreacted Hugoniot and a JWL equation of state for the reaction products, we estimated the initial reaction rate in the high explosive after the detonation wave front interacted with the foil to be 40 μs-1 for CP, 60 μs-1 for TNT, and 80 μs-1 for PBX-9502. The shape of the profiles indicates the reaction rate decreases as reaction proceeds.

  15. Modeling Hot-Spot Contributions in Shocked High Explosives at the Mesoscale

    SciTech Connect

    Harrier, Danielle

    2015-08-12

    When looking at performance of high explosives, the defects within the explosive become very important. Plastic bonded explosives, or PBXs, contain voids of air and bonder between the particles of explosive material that aid in the ignition of the explosive. These voids collapse in high pressure shock conditions, which leads to the formation of hot spots. Hot spots are localized high temperature and high pressure regions that cause significant changes in the way the explosive material detonates. Previously hot spots have been overlooked with modeling, but now scientists are realizing their importance and new modeling systems that can accurately model hot spots are underway.

  16. Characterizing high energy explosive eruptions at Stromboli volcano using multidisciplinary data: An example from the 9 January 2005 explosion

    NASA Astrophysics Data System (ADS)

    Andronico, D.; Corsaro, R. A.; Cristaldi, A.; Polacci, M.

    2008-10-01

    Stromboli is well known for its persistent, normal explosive activity, consisting of intermittent, mild to moderate, Strombolian explosions that typically occur every 10-20 min. All tephras erupted during this activity usually fall back into the crater terrace, and consist of volatile-poor scoriae fed by Highly Porphyritic (HP) magma. More occasionally, large explosions or "paroxysms" eject a greater quantity of tephra, mainly consisting of HP scoriae and pumice clasts of Low Porphyritic (LP) magma, but also including large lithic blocks. In addition to this activity, between 2004 and 2006 high energy explosions, displaying an intermediate eruptive style between that of normal and paroxysmal explosions in terms of column height, duration and tephra dispersal, were observed to occur at a frequency of one to eight events per year. While many volcanological, geochemical and geophysical studies have focused in the last few years on the two end-members of activity, i.e. normal or paroxysmal, a detailed investigation on these intermediate types of events has not been carried out yet. Here we report of a study on the 9 January 2005 explosion, one of the high energy explosions during which the main fountaining phase lasted nearly a minute causing ejection of coarse bombs up to a height of 120 m, and of ash and lapilli to > 200 m. An accompanying ash plume rose up to 500 m at the end of the explosion. We present a multidisciplinary approach that integrates the results from analysis of live-camera images with compositional and textural characterization of the erupted products. Major element composition of glassy groundmass and 3D views of textures in the erupted scoriae support the hypothesis based on volcanological observations that this explosion falls between normal and paroxysmal activity, for which we use the term "intermediate". By comparing the video-camera images of the 9 January 2005 explosion with volcanological features of other high energy explosions that

  17. Human Health and Ecological Risk Assessment for the Operation of the Explosives Waste Treatment Facility at Site 300 of the Lawrence Livermore National Laboratory

    SciTech Connect

    Gallegos, G; Daniels, J; Wegrecki, A

    2007-10-01

    This document contains the human health and ecological risk assessment for the Resource Recovery and Conservation Act (RCRA) permit renewal for the Explosives Waste Treatment Facility (EWTF). Volume 1 is the text of the risk assessment, and Volume 2 (provided on a compact disc) is the supporting modeling data. The EWTF is operated by the Lawrence Livermore National Laboratory (LLNL) at Site 300, which is located in the foothills between the cities of Livermore and Tracy, approximately 17 miles east of Livermore and 8 miles southwest of Tracy. Figure 1 is a map of the San Francisco Bay Area, showing the location of Site 300 and other points of reference. One of the principal activities of Site 300 is to test what are known as 'high explosives' for nuclear weapons. These are the highly energetic materials that provide the force to drive fissionable material to criticality. LLNL scientists develop and test the explosives and the integrated non-nuclear components in support of the United States nuclear stockpile stewardship program as well as in support of conventional weapons and the aircraft, mining, oil exploration, and construction industries. Many Site 300 facilities are used in support of high explosives research. Some facilities are used in the chemical formulation of explosives; others are locations where explosive charges are mechanically pressed; others are locations where the materials are inspected radiographically for such defects as cracks and voids. Finally, some facilities are locations where the machined charges are assembled before they are sent to the onsite test firing facilities, and additional facilities are locations where materials are stored. Wastes generated from high-explosives research are treated by open burning (OB) and open detonation (OD). OB and OD treatments are necessary because they are the safest methods for treating explosives wastes generated at these facilities, and they eliminate the requirement for further handling and

  18. First-principles study of high explosive decomposition energetics

    SciTech Connect

    Wu, C J

    1998-08-21

    The mechanism of the gas phase unimolecular decomposition of hexahydro-1,3,5,- trinitro- 1,3,5,-triazine (RDX) has been investigated using first principles gradient corrected density functional theory. Our results show that the dominant reaction channel is the N-NO* bond rupture, which has a barrier of 34.2 kcal/mol at the B- PW9 l/cc-pVDZ level and is 18.3 kcal/mol lower than that of the concerted ring fission to three methylenenitramine molecules. In addition, we have carried out a systematic study of homolytic bond dissociation energies of 14 other high explosives at the B-PW91/D95V level. We find that the correlation between the weakest bond strength and high explosive sensitivity is strong

  19. Shock response of the commercial high explosive Detasheet

    NASA Astrophysics Data System (ADS)

    Asay, B. W.; Ramsay, J. B.; Anderson, M. U.; Graham, R. A.

    1994-12-01

    The mechanical and chemical response of the flexible commercial high explosive DetasheetR is studied under controlled impact and plane-wave, high explosive loading. Results on nonreactive material behavior, sound speed, shock-initiation sensitivity and detonation pressure are presented. The material is found to respond in a viscous manner reminiscent of viscoelastic response of polymeric materials. Time-resolved pressure and pressure-rate measurements with PVDF piezoelectric polymer gauges are presented along with Manganin pressure and plate-dent test measurements of detonation pressure. Detonation pressures of 18GPa are indicated. Pressure measurements show initiation of reaction between 3 and 8 mm for an impact stress of 3.1 GPa. Plane wave loading wedge tests show run distances to detonation consistent with the pressure measurements, and with behavior like that of XTX8003 (80 % PETN/20 % Sylgard 182R).

  20. Integrated Experiment and Modeling of Insensitive High Explosives

    NASA Astrophysics Data System (ADS)

    Stewart, D. Scott; Lambert, David E.; Yoo, Sunhee; Lieber, Mark; Holman, Steven

    2009-12-01

    New design paradigms for insensitive high explosives are being sought for use in munitions applications that require enhanced safety, reliability and performance. We describe recent work of our group that uses an integrated approach to develop predictive models, guided by experiments. Insensitive explosive can have relatively longer detonation reaction zones and slower reaction rates than their sensitive counterparts. We employ reactive flow models that are constrained by detonation shock dynamics (DSD) to pose candidate predictive models. We discuss the variation of the pressure dependent reaction rate exponent and reaction order on the length of the supporting reaction zone, the detonation velocity curvature relation, the computed critical energy required for initiation, the relation between the diameter effect curve and the corresponding normal detonation velocity curvature relation.

  1. Integrated Experiment and Modeling of Insensitive High Explosives

    NASA Astrophysics Data System (ADS)

    Stewart, D. Scott; Lambert, David E.; Yoo, Sunhee; Lieber, M.; Holman, Steven

    2009-06-01

    New design paradigms for insensitive high explosives are being sought for use in munitions applications that require enhanced, safety, reliability and performance. We describe recent work of our group that uses an integrated approach to develop predictive models, guided by experiments. Insensitive explosive can have relatively longer detonation reaction zones and slower reaction rates than their sensitive counterparts. We employ reactive flow models that are constrained by detonation shock dynamics to pose candidate predictive models. We discuss variation of the pressure dependent reaction rate exponent and reaction order, on the length of the supporting reaction zone, the detonation velocity curvature relation, computed critical energy required for initiation, the relation between the diameter effect curve and the corresponding normal detonation velocity curvature relation. We discuss representative characterization experiments carried out at Eglin, AFB and the constraints imposed on models by a standardized experimental characterization sequence.

  2. Environmental assessment for the Explosive Waste Treatment Facility at Site 300, Lawrence Livermore National Laboratory

    SciTech Connect

    1995-11-01

    Lawrence Livermore National Laboratory proposes to build, permit, and operate the Explosive Waste Treatment Facility (EWTF) to treat explosive waste at LLNL`s Experimental Test Site, Site 300. It is also proposed to close the EWTF at the end of its useful life in accordance with the regulations. The facility would replace the existing Building 829 Open Burn Facility (B829) and would treat explosive waste generated at the LLNL Livermore Site and at Site 300 either by open burning or open detonation, depending on the type of waste. The alternatives addressed in the 1992 sitewide EIS/EIR are reexamined in this EA. These alternatives included: (1) the no-action alternative which would continue open burning operations at B829; (2) continuation of only open burning at a new facility (no open detonation); (3) termination of open burning operations with shipment of explosive waste offsite; and (4) the application of alternative treatment technologies. This EA examines the impact of construction, operation, and closure of the EWTF. Construction of the EWTF would result in the clearing of a small amount of previously disturbed ground. No adverse impact is expected to any state or federal special status plant or animal species (special status species are classified as threatened, endangered, or candidate species by either state or federal legislation). Operation of the EWTF is expected to result in a reduced threat to involved workers and the public because the proposed facility would relocate existing open burning operations to a more remote area and would incorporate design features to reduce the amount of potentially harmful emissions. No adverse impacts were identified for activities necessary to close the EWTF at the end of its useful life.

  3. High-speed imaging of explosive eruptions: applications and perspectives

    NASA Astrophysics Data System (ADS)

    Taddeucci, Jacopo; Scarlato, Piergiorgio; Gaudin, Damien; Capponi, Antonio; Alatorre-Ibarguengoitia, Miguel-Angel; Moroni, Monica

    2013-04-01

    Explosive eruptions, being by definition highly dynamic over short time scales, necessarily call for observational systems capable of relatively high sampling rates. "Traditional" tools, like as seismic and acoustic networks, have recently been joined by Doppler radar and electric sensors. Recent developments in high-speed camera systems now allow direct visual information of eruptions to be obtained with a spatial and temporal resolution suitable for the analysis of several key eruption processes. Here we summarize the methods employed to gather and process high-speed videos of explosive eruptions, and provide an overview of the several applications of these new type of data in understanding different aspects of explosive volcanism. Our most recent set up for high-speed imaging of explosive eruptions (FAMoUS - FAst, MUltiparametric Set-up,) includes: 1) a monochrome high speed camera, capable of 500 frames per second (fps) at high-definition (1280x1024 pixel) resolution and up to 200000 fps at reduced resolution; 2) a thermal camera capable of 50-200 fps at 480-120x640 pixel resolution; and 3) two acoustic to infrasonic sensors. All instruments are time-synchronized via a data logging system, a hand- or software-operated trigger, and via GPS, allowing signals from other instruments or networks to be directly recorded by the same logging unit or to be readily synchronized for comparison. FAMoUS weights less than 20 kg, easily fits into four, hand-luggage-sized backpacks, and can be deployed in less than 20' (and removed in less than 2', if needed). So far, explosive eruptions have been recorded in high-speed at several active volcanoes, including Fuego and Santiaguito (Guatemala), Stromboli (Italy), Yasur (Vanuatu), and Eyjafiallajokull (Iceland). Image processing and analysis from these eruptions helped illuminate several eruptive processes, including: 1) Pyroclasts ejection. High-speed videos reveal multiple, discrete ejection pulses within a single Strombolian

  4. Mechanical Behavior of TNAZ/CAB Explosives during High Acceleration

    NASA Astrophysics Data System (ADS)

    Lanzerotti, Y.; Capellos, C.; Travers, B.; Sharma, J.

    2004-07-01

    The mechanical behavior of melt-cast TNAZ/CAB (1,3,3-trinitroazetidine/cellulose acetate butyrate) explosives subjected to high acceleration has been studied in an ultracentrifuge at -10°C and 25°C. Melt-cast TNAZ/CAB was studied as a function of the percentage of the composition of CAB at -10°C and 25°C. The percentage of CAB in the samples varied from 0.5% to 3%. Failure occurs when the shear or tensile strength of the explosive is exceeded. The fracture acceleration of melt-cast TNAZ/CAB increases with the percentage of CAB in the explosive at both temperatures studied, -10°C and 25°C. While there is some variation among samples, it is found that the fracture acceleration of melt-cast 99%/1% TNAZ/CAB and melt-cast 99.5%/0.5% TNAZ/CAB at -10°C is less than that at 25°C.

  5. Research and Development of High-performance Explosives.

    PubMed

    Cornell, Rodger; Wrobel, Erik; Anderson, Paul E

    2016-01-01

    Developmental testing of high explosives for military applications involves small-scale formulation, safety testing, and finally detonation performance tests to verify theoretical calculations. small-scale For newly developed formulations, the process begins with small-scale mixes, thermal testing, and impact and friction sensitivity. Only then do subsequent larger scale formulations proceed to detonation testing, which will be covered in this paper. Recent advances in characterization techniques have led to unparalleled precision in the characterization of early-time evolution of detonations. The new technique of photo-Doppler velocimetry (PDV) for the measurement of detonation pressure and velocity will be shared and compared with traditional fiber-optic detonation velocity and plate-dent calculation of detonation pressure. In particular, the role of aluminum in explosive formulations will be discussed. Recent developments led to the development of explosive formulations that result in reaction of aluminum very early in the detonation product expansion. This enhanced reaction leads to changes in the detonation velocity and pressure due to reaction of the aluminum with oxygen in the expanding gas products. PMID:26966969

  6. Research and Development of High-performance Explosives

    PubMed Central

    Cornell, Rodger; Wrobel, Erik; Anderson, Paul E.

    2016-01-01

    Developmental testing of high explosives for military applications involves small-scale formulation, safety testing, and finally detonation performance tests to verify theoretical calculations. small-scale For newly developed formulations, the process begins with small-scale mixes, thermal testing, and impact and friction sensitivity. Only then do subsequent larger scale formulations proceed to detonation testing, which will be covered in this paper. Recent advances in characterization techniques have led to unparalleled precision in the characterization of early-time evolution of detonations. The new technique of photo-Doppler velocimetry (PDV) for the measurement of detonation pressure and velocity will be shared and compared with traditional fiber-optic detonation velocity and plate-dent calculation of detonation pressure. In particular, the role of aluminum in explosive formulations will be discussed. Recent developments led to the development of explosive formulations that result in reaction of aluminum very early in the detonation product expansion. This enhanced reaction leads to changes in the detonation velocity and pressure due to reaction of the aluminum with oxygen in the expanding gas products. PMID:26966969

  7. Engineering support for LLNL Chemistry's High Explosive Technology group. Final report

    SciTech Connect

    Weston, A.M.; James, E.

    1985-12-01

    Support for the Lawrence Livermore National Laboratory (LLNL) High Explosive Technology (HET), part of the Chemistry Division is described. Brief progress reports are presented for the following six tasks: (1) assess mechanical and explosive response of proposed extreme environmental weapon systems; (2) perform a hazard study relating to Trident D-5 motor response; (3) continue development and application of the deflagration to detonation (DDT) computer model (code RDUCT) for the hazard assessment for rocket propellants (HARP) program; (4) perform rocket motor vulnerability calculations for a proposed new air force mobile missile; (5) perform additional analyses relating to radioisotope thermo-electric generator PuO2 containment with possible NASA space shuttle accident scenarios; and (6) develop a relational data base for information pertinent to the hazard studies relating to the Trident D-5 motor response and the associated HARP program. (AT)

  8. Conversion of high explosive chemical energy into energy of powerful nanosecond high-current pulses

    NASA Astrophysics Data System (ADS)

    Gorbachev, K. V.; Mikhaylov, V. M.; Nesterov, E. V.; Stroganov, V. A.; Chernykh, E. V.

    2015-01-01

    This study is a contribution into the development of physicotechnical foundations for generation of powerful nanosecond high-current pulses on the basis of explosively driven magnetic flux compression generators. This problem is solved by using inductive storage of energy for matching comparatively low-voltage explosively driven magnetic flux compression generators and high-impedance loads; short forming lines and vacuum diodes. Experimental data of charging of forming lines are given.

  9. Photoactive High Explosives: Substituents Effects on Tetrazine Photochemistry and Photophysics.

    PubMed

    McGrane, S D; Bolme, C A; Greenfield, M T; Chavez, D E; Hanson, S K; Scharff, R J

    2016-02-18

    High explosives that are photoactive, i.e., can be initiated with light, offer significant advantages in reduced potential for accidental electrical initiation. We examined a series of structurally related tetrazine based photoactive high explosive materials to detail their photochemical and photophysical properties. Using photobleaching infrared absorption, we determined quantum yields of photochemistry for nanosecond pulsed excitation at 355 and 532 nm. Changes in mass spectrometry during laser irradiation in vacuum measured the evolution of gaseous products. Fluorescence spectra, quantum yields, and lifetimes were measured to observe radiative channels of energy decay that compete with photochemistry. For the 6 materials studied, quantum yields of photochemistry ranged from <10(-5) to 0.03 and quantum yield of fluorescence ranged from <10(-3) to 0.33. In all cases, the photoexcitation nonradiatively relaxed primarily to heat, appropriate for supporting photothermal initiation processes. The photochemistry observed was dominated by ring scission of the tetrazine, but there was evidence of more extensive multistep reactions as well. PMID:26797486

  10. Photoactive High Explosives: Substituents Effects on Tetrazine Photochemistry and Photophysics.

    PubMed

    McGrane, S D; Bolme, C A; Greenfield, M T; Chavez, D E; Hanson, S K; Scharff, R J

    2016-02-18

    High explosives that are photoactive, i.e., can be initiated with light, offer significant advantages in reduced potential for accidental electrical initiation. We examined a series of structurally related tetrazine based photoactive high explosive materials to detail their photochemical and photophysical properties. Using photobleaching infrared absorption, we determined quantum yields of photochemistry for nanosecond pulsed excitation at 355 and 532 nm. Changes in mass spectrometry during laser irradiation in vacuum measured the evolution of gaseous products. Fluorescence spectra, quantum yields, and lifetimes were measured to observe radiative channels of energy decay that compete with photochemistry. For the 6 materials studied, quantum yields of photochemistry ranged from <10(-5) to 0.03 and quantum yield of fluorescence ranged from <10(-3) to 0.33. In all cases, the photoexcitation nonradiatively relaxed primarily to heat, appropriate for supporting photothermal initiation processes. The photochemistry observed was dominated by ring scission of the tetrazine, but there was evidence of more extensive multistep reactions as well.

  11. High Explosive Verification and Validation: Systematic and Methodical Approach

    NASA Astrophysics Data System (ADS)

    Scovel, Christina; Menikoff, Ralph

    2011-06-01

    Verification and validation of high explosive (HE) models does not fit the standard mold for several reasons. First, there are no non-trivial test problems with analytic solutions. Second, an HE model depends on a burn rate and the equation of states (EOS) of both the reactants and products. Third, there is a wide range of detonation phenomena from initiation under various stimuli to propagation of curved detonation fronts with non-rigid confining materials. Fourth, in contrast to a shock wave in a non-reactive material, the reaction-zone width is physically significant and affects the behavior of a detonation wave. Because of theses issues, a systematic and methodical approach to HE V & V is needed. Our plan is to build a test suite from the ground up. We have started with the cylinder test and have run simulations with several EOS models and burn models. We have compared with data and cross-compared the different runs to check on the sensitivity to model parameters. A related issue for V & V is what experimental data are available for calibrating and testing models. For this purpose we have started a WEB based high explosive database (HED). The current status of HED will be discussed.

  12. Field-based high-speed imaging of explosive eruptions

    NASA Astrophysics Data System (ADS)

    Taddeucci, J.; Scarlato, P.; Freda, C.; Moroni, M.

    2012-12-01

    Explosive eruptions involve, by definition, physical processes that are highly dynamic over short time scales. Capturing and parameterizing such processes is a major task in eruption understanding and forecasting, and a task that necessarily requires observational systems capable of high sampling rates. Seismic and acoustic networks are a prime tool for high-frequency observation of eruption, recently joined by Doppler radar and electric sensors. In comparison with the above monitoring systems, imaging techniques provide more complete and direct information of surface processes, but usually at a lower sampling rate. However, recent developments in high-speed imaging systems now allow such information to be obtained with a spatial and temporal resolution suitable for the analysis of several key eruption processes. Our most recent set up for high-speed imaging of explosive eruptions (FAMoUS - FAst, MUltiparametric Set-up,) includes: 1) a monochrome high speed camera, capable of 500 frames per second (fps) at high-definition (1280x1024 pixel) resolution and up to 200000 fps at reduced resolution; 2) a thermal camera capable of 50-200 fps at 480-120x640 pixel resolution; and 3) two acoustic to infrasonic sensors. All instruments are time-synchronized via a data logging system, a hand- or software-operated trigger, and via GPS, allowing signals from other instruments or networks to be directly recorded by the same logging unit or to be readily synchronized for comparison. FAMoUS weights less than 20 kg, easily fits into four, hand-luggage-sized backpacks, and can be deployed in less than 20' (and removed in less than 2', if needed). So far, explosive eruptions have been recorded in high-speed at several active volcanoes, including Fuego and Santiaguito (Guatemala), Stromboli (Italy), Yasur (Vanuatu), and Eyjafiallajokull (Iceland). Image processing and analysis from these eruptions helped illuminate several eruptive processes, including: 1) Pyroclasts ejection. High

  13. Laser impingement on bare and encased high explosives: safety limits

    SciTech Connect

    Roeske, F

    1999-03-15

    During the course of experiments involving high explosives, (HE), alignment lasers are often employed where the laser beam impinges upon a metal encased HE sample or on the bare HE itself during manned operations. While most alignment lasers are of low enough power so as not to be of concern, safety questions arise when considering the maximum credible power output of the laser in a failure mode, or when multiple laser spots are focused onto the experiment simultaneously. Safety questions also arise when the focused laser spot size becomes very small, on the order of 100 {micro}m or less. This paper addresses these concerns by describing a methodology for determining safety margins for laser impingement on metal encased HE as well as one for bare HE. A variety of explosives encased in Al, Cu, Ta and stainless steel were tested using the first of these techniques. Additional experiments were performed using the second method where the laser beam was focused directly on eight different samples of pressed-powder HE.

  14. High Resolution Digital Elevation Models of Pristine Explosion Craters

    NASA Technical Reports Server (NTRS)

    Farr, T. G.; Krabill, W.; Garvin, J. B.

    2004-01-01

    In order to effectively capture a realistic terrain applicable to studies of cratering processes and landing hazards on Mars, we have obtained high resolution digital elevation models of several pristine explosion craters at the Nevada Test Site. We used the Airborne Terrain Mapper (ATM), operated by NASA's Wallops Flight Facility to obtain DEMs with 1 m spacing and 10 cm vertical errors of 4 main craters and many other craters and collapse pits. The main craters that were mapped are Sedan, Scooter, Schooner, and Danny Boy. The 370 m diameter Sedan crater, located on Yucca Flat, is the largest and freshest explosion crater on Earth that was formed under conditions similar to hypervelocity impact cratering. As such, it is effectively pristine, having been formed in 1962 as a result of a controlled detonation of a 100 kiloton thermonuclear device, buried at the appropriate equivalent depth of burst required to make a simple crater. Sedan was formed in alluvium of mixed lithology and subsequently studied using a variety of field-based methods. Nearby secondary craters were also formed at the time and were also mapped by ATM. Adjacent to Sedan and also in alluvium is Scooter, about 90 m in diameter and formed by a high-explosive event. Schooner (240 m) and Danny Boy (80 m) craters were also important targets for ATM as they were excavated in hard basalt and therefore have much rougher ejecta. This will allow study of ejecta patterns in hard rock as well as engineering tests of crater and rock avoidance and rover trafficability. In addition to the high resolution DEMs, crater geometric characteristics, RMS roughness maps, and other higher-order derived data products will be generated using these data. These will provide constraints for models of landing hazards on Mars and for rover trafficability. Other planned studies will include ejecta size-frequency distribution at the resolution of the DEM and at finer resolution through air photography and field measurements

  15. Steam-explosion safety considerations for the Advanced Neutron Source Reactor at the Oak Ridge National Laboratory

    SciTech Connect

    Taleyarkhan, R.

    1990-02-01

    This report provides a perspective on steam-explosion safety and design issues for the Advanced Neutron Source (ANS) reactor being designed at the Oak Ridge National Laboratory. A historical background along with a description of experiments and analytical work performed to date has been provided. Preliminary analyses (for the ANS) have been conducted to evaluate steam-explosion pressure- pulse loadings, the effects of reactor coolant system (RCS) overpressurization, and slug energetics. The method used for pressure-pulse magnitude evaluation was benchmarked with previous calculations, an aluminum-water steam-explosion experiment, and test reactor steam explosion data with good agreement. Predicted pressure-pulse magnitudes evaluated were found to be several orders of magnitude lower than corresponding values evaluated by correlating available energies with shock-wave pressures from equivalent chemical detonations. The preliminary best estimate, as well as conservative estimates for RCS volume-pressurization failure and slug energetics for RCS volume-pressurization failure and slug energetics, indicated that (1) steam explosions in the ANS have significant damage potential, and (2) steam-explosion issues must be considered during the design phase of the ANS Project. Recommendations are made for efficiently addressing this important safety and design issue. 38 refs., 17 figs., 11 tabs.

  16. Biodegradation of the high explosive hexanitrohexaazaiso-wurtzitane (CL-20).

    PubMed

    Karakaya, Pelin; Christodoulatos, Christos; Koutsospyros, Agamemnon; Balas, Wendy; Nicolich, Steve; Sidhoum, Mohammed

    2009-04-01

    The aerobic biodegradability of the high explosive CL-20 by activated sludge and the white rot fungus Phanerochaete chrysosporium has been investigated. Although activated sludge is not effective in degrading CL-20 directly, it can mineralize the alkaline hydrolysis products. Phanerochaete chrysosporium degrades CL-20 in the presence of supplementary carbon and nitrogen sources. Biodegradation studies were conducted using various nutrient media under diverse conditions. Variables included the CL-20 concentration; levels of carbon (as glycerol) and ammonium sulfate and yeast extract as sources of nitrogen. Cultures that received CL-20 at the time of inoculation transformed CL-20 completely under all nutrient conditions studied. When CL-20 was added to pre-grown cultures, degradation was limited. The extent of mineralization was monitored by the (14)CO(2) time evolution; up to 51% mineralization was achieved when the fungus was incubated with [(14)C]-CL-20. The kinetics of CL-20 biodegradation by Phanerochaete chrysosporium follows the logistic kinetic growth model.

  17. On detonation wave front structure of consensed high explosives

    NASA Astrophysics Data System (ADS)

    Fedorov, A. V.; Menshikh, A. V.; Yagodin, N. B.

    1998-07-01

    The present report describes detonation front particle velocity profile measurements for three high explosives (HE). Two were plasticized compositions based on PETN, HMX, and the third a TNT/RDX 50/50 mixture. Measurements were carried out using laser interferometry techniques with few nanosecond time resolution. Particle velocity profiles were recorded at HE-window (lithium fluoride [LiF]) interfaces. The detonation waves were diverging since they developed from a single initiation point. Recorded maximum particle velocities at the LiF window interfaces for PETN, HMX, and TNT/RDX mixture were 2.7 mm/μs, 3.15 mm/μs and 2.6 mm/μs, respectively. Duration of chemical reaction zone for HEs based on PETN and HMX were determined. The results of linear extrapolation of recorded particle velocity to zero time are presented, leading to estimates of von Neumann spike parameters for the PETN and HMX compositions.

  18. Moderate Velocity Ball Impact of a Mock High-Explosive

    SciTech Connect

    Furmanski, Jevan; Rae, Philip; Clements, Bradford E.

    2012-06-05

    Modeling of thermal and mechanical events in high-explosive materials is complicated by the composite nature of the material, which experiences viscoelastic and plastic deformations and sustains damage in the form of microcracks that can dominate its overall behavior. A mechanical event of interest is projectile interaction with the material, which leads to extreme local deformation and adiabatic heating, which can potentially lead to adverse outcomes in an energetic material. Simulations of such an event predicted large local temperature rises near the path of a spherical projectile, but these were experimentally unconfirmed and hence potentially non-physical. This work concerns the experimental verification of local temperatures both at the surface and in the wake of a spherical projectile penetrating a mock (unreactive) high-explosive at {approx}700 m/s. Fast response thermocouples were embedded radially in a mid-plane of a cylindrical target, which was bonded around the thermocouples with epoxy and recorded by an oscilloscope through a low-pass filter with a bandwidth of 500 Hz. A peak temperature rise of 70 K was measured both at the equator of the projectile and in its wake, in good agreement with the temperature predicted in the minimally distorted elements at those locations by a finite element model in ABAQUS employing the ViscoSCRAM constitutive model. Further work is needed to elucidate the extreme temperature rises in material undergoing crushing or fragmentation, which is difficult to predict with meshed finite element methods due to element distortion, and also challenging to quantify experimentally.

  19. High level triggers for explosive mafic volcanism: Albano Maar, Italy

    NASA Astrophysics Data System (ADS)

    Cross, J. K.; Tomlinson, E. L.; Giordano, G.; Smith, V. C.; De Benedetti, A. A.; Roberge, J.; Manning, C. J.; Wulf, S.; Menzies, M. A.

    2014-03-01

    Colli Albani is a quiescent caldera complex located within the Roman Magmatic Province (RMP), Italy. The recent Via dei Laghi phreatomagmatic eruptions led to the formation of nested maars. Albano Maar is the largest and has erupted seven times between ca 69-33 ka. The highly explosive nature of the Albano Maar eruptions is at odds with the predominant relatively mafic (SiO2 = 48-52 wt.%) foiditic (K2O = 9 wt.%) composition of the magma. The deposits have been previously interpreted as phreatomagmatic, however they contain large amounts (up to 30%vol) of deep seated xenoliths, skarns and all pre-volcanic subsurface units. All of the xenoliths have been excavated from depths of up to 6 km, rather than being limited to the depth at which magma and water interaction is likely to have occurred, suggesting an alternative trigger for eruption. High precision geochemical glass and mineral data of fresh juvenile (magmatic) clasts from the small volume explosive deposits indicate that the magmas have evolved along one of two evolutionary paths towards foidite or phonolite. The foiditic melts record ca. 50% mixing between the most primitive magma and Ca-rich melt, late stage prior to eruption. A major result of our study is finding that the generation of Ca-rich melts via assimilation of limestone, may provide storage for significant amounts of CO2 that can be released during a mixing event with silicate magma. Differences in melt evolution are inferred as having been controlled by variations in storage conditions: residence time and magma volume.

  20. Infrared spectrometry and radiometry of high-explosive detonations: the Los Alamos experiments

    SciTech Connect

    Rogers, E H; Williams, R L; Frazier, E N; Stone, D K; Herr, K C; Young, R M; Robbins, R G

    1982-11-01

    The purpose of these experiments was to determine whether the infrared spectra of high-explosive detonations can be used to infer the type of explosive material and/or the containment material employed. Infrared spectra and radiometric traces were measured during a test series of twenty-three detonations; some were contained and some uncontained. A variety of high-explosive materials and containment materials were included. The explosive charge was typically about 175 g. Infrared spectra were taken at the rate of 250 spectra/sec. This rate was too slow to characterize the very early gas expansion or burn pase of these explosions. The infrared spectra of the delayed or afterburn phase of these explosions often displayed molecular emission and absorption features. Absorption by NH/sub 3/ was observed when C-4 was the high-explosive material, and not observed for any other material. Emissions from H/sub 2/O and CO/sub 2/ were observed part of the time. Their occurence does not seem to be correlated with the type of containment or type of high-explosive material, or peak temperature reached in the afterburn. From the radiometric traces, one concludes that the relative peak radiance from the burn and afterburn phases depend strongly on the type of high-explosive material. For similar devices the burn phase is consistent from shot to shot, whereas the afterburn is very inconsistent. The answer to the question whether infrared spectra of high-explosive detonations can be used to infer the type of explosive material and/or the containment material must await spectral observations of the burn phase. We now believe that spectra of the burn phase are likely to be the ones most useful in identifying the high-explosive or containment material.

  1. Analysis of lightning-related risk in outdoor high explosive research.

    SciTech Connect

    Eisenhawer, S. W.; Bott, T. F.

    2002-01-01

    The behavior of materials at high strain rates can be studied using high explosives (HE) as an energy source. Such hydrodynamic experiments may be performed on full-scale systems, requiring kilogram quantities of HE and therefore are performed at outdoor facilities. One such facility is DARHT-the Dual-Axis Radiographic Hydrodynamic Test facility located at Los Alamos National Laboratory in northern New Mexico. DARHT is a very large flash x-ray machine. The high-intensity, short-duration x-ray pulses are beamed through the hydrodynamic experiment to an x-ray camera. Density variations in the materials produce variations in the transmitted beam that are recorded by the camera. The information in these images is used to understand the basic behavior of materials subjected to very high dynamic pressures and to evaluate the accuracy of computer codes used to model the associated phenomena.

  2. DMSO/base hydrolysis method for the disposal of high explosives and related energetic materials

    DOEpatents

    Desmare, Gabriel W.; Cates, Dillard M.

    2002-05-14

    High explosives and related energetic materials are treated via a DMSO/base hydrolysis method which renders them non-explosive and/or non-energetic. For example, high explosives such as 1,3,5,7-tetraaza-1,3,5,7-tetranitrocyclooctane (HMX), 1,3,5-triaza-1,3,5-trinitrocyclohexane (RDX), 2,4,6-trinitrotoluene (TNT), or mixtures thereof, may be dissolved in a polar, aprotic solvent and subsequently hydrolyzed by adding the explosive-containing solution to concentrated aqueous base. Major hydrolysis products typically include nitrite, formate, and nitrous oxide.

  3. High Energy Density Laboratory Astrophysics

    SciTech Connect

    Remington, B A

    2004-11-11

    High-energy-density (HED) physics refers broadly to the study of macroscopic collections of matter under extreme conditions of temperature and density. The experimental facilities most widely used for these studies are high-power lasers and magnetic-pinch generators. The HED physics pursued on these facilities is still in its infancy, yet new regimes of experimental science are emerging. Examples from astrophysics include work relevant to planetary interiors, supernovae, astrophysical jets, and accreting compact objects (such as neutron stars and black holes). In this paper, we will review a selection of recent results in this new field of HED laboratory astrophysics and provide a brief look ahead to the coming decade.

  4. Systematic approach to verification and validation: High explosive burn models

    SciTech Connect

    Menikoff, Ralph; Scovel, Christina A.

    2012-04-16

    Most material models used in numerical simulations are based on heuristics and empirically calibrated to experimental data. For a specific model, key questions are determining its domain of applicability and assessing its relative merits compared to other models. Answering these questions should be a part of model verification and validation (V and V). Here, we focus on V and V of high explosive models. Typically, model developers implemented their model in their own hydro code and use different sets of experiments to calibrate model parameters. Rarely can one find in the literature simulation results for different models of the same experiment. Consequently, it is difficult to assess objectively the relative merits of different models. This situation results in part from the fact that experimental data is scattered through the literature (articles in journals and conference proceedings) and that the printed literature does not allow the reader to obtain data from a figure in electronic form needed to make detailed comparisons among experiments and simulations. In addition, it is very time consuming to set up and run simulations to compare different models over sufficiently many experiments to cover the range of phenomena of interest. The first difficulty could be overcome if the research community were to support an online web based database. The second difficulty can be greatly reduced by automating procedures to set up and run simulations of similar types of experiments. Moreover, automated testing would be greatly facilitated if the data files obtained from a database were in a standard format that contained key experimental parameters as meta-data in a header to the data file. To illustrate our approach to V and V, we have developed a high explosive database (HED) at LANL. It now contains a large number of shock initiation experiments. Utilizing the header information in a data file from HED, we have written scripts to generate an input file for a hydro code

  5. Increased shock sensitivity of the insensitive explosive LX-17 at high temperatures

    SciTech Connect

    Lee, R.S.; Chau, H.H.

    1994-05-01

    Explosive formulations based on TATB (1.3.5-trichloro-2,4,6-trinitrobenzene) have proven to be remarkably insensitive to shock and thermal stimuli. However, hazards to an insensitive high explosive (IHE) charge do not always confine themselves to a single stimulus. In the study reported here, we have investigated the response of the LLNL explosive LX-17 (92.5%/7.5% TATB/Kel-F 800) to shock when the explosive is at an elevated temperature. The motivation for the work was to learn the extent to which the shock initiation threshold and critical initiation area of LX-17 are lowered by exposure to elevated temperature.

  6. Biodegradation of the high explosive hexanitrohexaazaiso-wurtzitane (CL-20).

    PubMed

    Karakaya, Pelin; Christodoulatos, Christos; Koutsospyros, Agamemnon; Balas, Wendy; Nicolich, Steve; Sidhoum, Mohammed

    2009-04-01

    The aerobic biodegradability of the high explosive CL-20 by activated sludge and the white rot fungus Phanerochaete chrysosporium has been investigated. Although activated sludge is not effective in degrading CL-20 directly, it can mineralize the alkaline hydrolysis products. Phanerochaete chrysosporium degrades CL-20 in the presence of supplementary carbon and nitrogen sources. Biodegradation studies were conducted using various nutrient media under diverse conditions. Variables included the CL-20 concentration; levels of carbon (as glycerol) and ammonium sulfate and yeast extract as sources of nitrogen. Cultures that received CL-20 at the time of inoculation transformed CL-20 completely under all nutrient conditions studied. When CL-20 was added to pre-grown cultures, degradation was limited. The extent of mineralization was monitored by the (14)CO(2) time evolution; up to 51% mineralization was achieved when the fungus was incubated with [(14)C]-CL-20. The kinetics of CL-20 biodegradation by Phanerochaete chrysosporium follows the logistic kinetic growth model. PMID:19440524

  7. Tilt Correction of High Explosive Test Data with Examples

    NASA Astrophysics Data System (ADS)

    Hill, Larry; Francois, Elizabeth; Morris, John

    2013-06-01

    Many high-explosive experiments view a nominally-axially-symmetric detonation wave breaking through a charge surface. Emerging waves virtually always exhibit a degree of tilt, which one generally wants to excise from the data whilst quantifying its direction and magnitude. In some cases, such as front-curvature rate sticks and Onionskin (OS)-type tests, the diagnostic is a single-slit streak camera (1D correction). In other cases, such as a Plane-Wave Lens characterization test or a Furball test, multiple slits or fibers provide sparse data over a surface (2D correction). We demonstrate both 1D and 2D corrections, the latter of which is the more challenging. In 2D, we represent the breakout time as the sum of a symmetric component and an asymmetric component (a tilted plane). The two tilt angle components are found that minimize the data scatter associated with the symmetric component. The most compelling example is the Furball test, an OS-variant for which the breakout time over the hemispherical observation surface is measured at many points using optical fibers. Unlike the OS test that looks in one (random) direction, we are able to construct OS-type data in the direction of maximum tilt, even though there are generally no fibers at that direction.

  8. Biodegradation of the High Explosive Hexanitrohexaazaiso-wurtzitane (CL-20)

    PubMed Central

    Karakaya, Pelin; Christodoulatos, Christos; Koutsospyros, Agamemnon; Balas, Wendy; Nicolich, Steve; Sidhoum, Mohammed

    2009-01-01

    The aerobic biodegradability of the high explosive CL-20 by activated sludge and the white rot fungus Phanerochaete chrysosporium has been investigated. Although activated sludge is not effective in degrading CL-20 directly, it can mineralize the alkaline hydrolysis products. Phanerochaete chrysosporium degrades CL-20 in the presence of supplementary carbon and nitrogen sources. Biodegradation studies were conducted using various nutrient media under diverse conditions. Variables included the CL-20 concentration; levels of carbon (as glycerol) and ammonium sulfate and yeast extract as sources of nitrogen. Cultures that received CL-20 at the time of inoculation transformed CL-20 completely under all nutrient conditions studied. When CL-20 was added to pre-grown cultures, degradation was limited. The extent of mineralization was monitored by the 14CO2 time evolution; up to 51% mineralization was achieved when the fungus was incubated with [14C]-CL-20. The kinetics of CL-20 biodegradation by Phanerochaete chrysosporium follows the logistic kinetic growth model. PMID:19440524

  9. Pressure Wave Measurements During Thermal Explosion of HMX-Based High Explosives

    SciTech Connect

    Forbes, J W; Garcia, F; Tarver, C M; Urtiew, P A; Greenwood, D W; Vandersall, K S

    2002-06-27

    Five different experiments on thermal heating of explosive materials have been performed. Three experiments thermally exploded PBX 9501 (HMX/Estane/BDNPA-F; 9512.512.5 wt %) donor charges while two others thermally exploded LX-04 (HMX/Viton A; 85/15 wt %). These donor charges were encased in 304 stainless steel. The transmitted two-dimensional pressure waves were measured by gauges in acceptor cylinders of Teflon, PBX 9501, or LX-04 that were in contact with the donors' steel case. A fifth experiment measured the pressure in an acceptor charge of PBX 9501 that had a 100 mm stand-off from the top of the steel case of the thermally cooked off PBX 9501 donor charge. Reactive flow hydrodynamic modeling using a rapid deflagration velocity of approximately 500 m/s was able to reproduce the pressure gauge records for both the in contact and stand off experiments that used PBX 9501 donors and acceptors.

  10. LOW OZONE-DEPLETING HALOCARBONS AS TOTAL-FLOOD AGENTS: VOLUME 2. LABORATORY-SCALE FIRE SUPPRESSION AND EXPLOSION PREVENTION TESTING

    EPA Science Inventory

    The report gives results from (1) flame suppression testing of potential Halon-1301 (CF3Br) replacement chemicals in a laboratory cup burner using n-heptane fuel and (2) explosion prevention (inertion) testing in a small-scale explosion sphere using propane and methane as fuels. ...

  11. Secondary wastes and high explosive residues generated during production of main high explosive charges for nuclear weapons

    SciTech Connect

    Jardine, L.J.; McGee, J.T.

    1994-02-01

    This study identifies the sources of high-explosive (HE) residues and hazardous and nonhazardous wastes generated during the production of the main HE charges for nuclear weapons, and estimates their quantities and characteristics. The results can be used as a basis for design of future handling and treatment systems for solid and liquid HE residues and wastes at any proposed new HE production facilities. This paper outlines a general methodology for documenting and estimating the volumes and characteristics of the solid and liquid HE residues and hazardous and nonhazardous wastes. We prepared volume estimates by applying this method to actual past Pantex plant HE production operations. To facilitate the estimating, we separated the HE main-charge production process into ten discrete unit operations and four support operations, and identified the corresponding solid and liquid HE residues and waste quantities. Four different annual HE main-charge production rates of 100, 500, 1000, and 2000 HE units/yr were assumed to develop the volume estimates and to establish the sensitivity of the estimates to HE production rates. The total solids (HE residues and hazardous and nonhazardous wastes) estimated range from 800 to 2800 ft{sup 3}/yr and vary uniformly with the assumed HE production rate. The total liquids estimated range from 73,000 to 1,448,000 gal/yr and also vary uniformly with the assumed production rate.

  12. Uncertainty quantification of a containment vessel dynamic response subjected to high-explosive detonation impulse loading

    SciTech Connect

    Rodriguez, E. A.; Pepin, J. E.; Thacker, B. H.; Riha, D. S.

    2002-01-01

    Los Alamos National Laboratory (LANL), in cooperation with Southwest Research Institute, has been developing capabilities to provide reliability-based structural evaluation techniques for performing weapon component and system reliability assessments. The development and applications of Probabilistic Structural Analysis Methods (PSAM) is an important ingredient in the overall weapon reliability assessments. Focus, herein, is placed on the uncertainty quantification associated with the structural response of a containment vessel for high-explosive (HE) experiments. The probabilistic dynamic response of the vessel is evaluated through the coupling of the probabilistic code NESSUS with the non-linear structural dynamics code, DYNA-3D. The probabilistic model includes variations in geometry and mechanical properties, such as Young's Modulus, yield strength, and material flow characteristics. Finally, the probability of exceeding a specified strain limit, which is related to vessel failure, is determined.

  13. Model testing of a 10-kg high explosive blast attenuation maze

    SciTech Connect

    Bacigalupi, C.M.; Burton, W.A.

    1981-07-01

    The basement area of the proposed High Explosive Applications Facility (HEAF) at the Lawrence Livermore National Laboratory includes 10-kg HE assembly and process cells, and a 10-kg corridor for the transport of up to 10 kg of HE from the receiving dock to the cells and to the experimental firing tanks. Previous model experiments developed a process cell-maze configuration that attenuated the effects of an accidental 10-kg detonation to acceptable levels (maximum of 10 to 11 psi reflected). This document reports 1/8-scale model tests conducted to confirm the maze design and to determine the blast pressures in adjacent areas in the final HEAF building configuration. In addition, pressure/time information was obtained at selected points in the model expansion chamber to provide the architect-engineer with information for structural design.

  14. High explosive corner turning performance and the LANL mushroom test

    SciTech Connect

    Hill, L.G.; Seitz, W.L.; Forest, C.A.; Harry, H.H.

    1998-07-01

    The Mushroom test is designed to characterize the corner turning performance of a new generation of less sensitive booster explosives. The test is described in detail, and three corner turning figures-of-merit are examined using pure TATB (both Livermore{close_quote}s Ultrafine and a Los Alamos research blend) and PBX9504 as examples. {copyright} {ital 1998 American Institute of Physics.}

  15. High explosive corner turning performance and the LANL Mushroom test

    SciTech Connect

    Hill, L.G.; Seitz, W.L.; Forest, C.A.; Harry, H.H.

    1997-09-01

    The Mushroom test is designed to characterize the corner turning performance of a new generation of less insensitive booster explosives. The test is described in detail, and three corner turning figures-of-merit are examined using pure TATB (both Livermore`s Ultrafine and a Los Alamos research blend) and PBX9504 as examples.

  16. Detonation Initiation of Heterogeneous Melt-Cast High Explosives

    NASA Astrophysics Data System (ADS)

    Chuzeville, Vincent; Baudin, Gerard; Lefrancois, Alexandre; Boulanger, Remi; Catoire, Laurent

    2015-06-01

    The melt-cast explosives' shock initiation mechanisms are less investigated than pressed and cast-cured ones. If the existence of hot-spots is widely recognized, their formation mechanism is not yet established. We study here two melt-cast explosives, NTO-TNT 60:40 and RDX-TNT 60:40 in order to establish a relation between the microstructure and the reaction rate using a two-phase model based on a ZND approach. Such a model requires the reaction rate, the equations of state of the unreacted phase and of the detonation products and an interaction model between the two phases to describe the reaction zone thermodynamics. The reaction rate law can be written in a factorized form including the number of initiation sites, the explosive's deflagration velocity around hot spots and a function depending on gas volume fraction produced by the deflagration front propagation. The deflagration velocity mainly depends on pressure and is determined from pop-plot tests using the hypothesis of the single curve build-up. This hypothesis has been verified for our two melt-cast explosives. The function depending on gas volume fraction is deduced from microstructural observations and from an analogy with the solid nucleation and growth theory. It has been established for deflagration fronts growing from grain's surface and a given initial grain size distribution. The model requires only a few parameters, calibrated thanks to an inversion method. A good agreement is obtained between experiments and numerical simulations.

  17. Initial characterization of a highly contaminated high explosives outfall in preparation for in situ bioremediation

    SciTech Connect

    Betty A. Strietelmeier; Patrick J. Coyne; Patricia A. Leonard; W. Lamar Miller; Jerry R. Brian

    1999-12-01

    In situ bioremediation is a viable, cost-effective treatment for environmental contamination of many kinds. The feasibility of using biological techniques to remediate soils contaminated with high explosives (HE) requires laboratory evaluation before proceeding to a larger scale field operation. Laboratory investigations have been conducted at pilot scale which indicate that an anaerobic process could be successful at reducing levels of HE, primarily HMX, RDX and TNT, in contaminated soils. A field demonstration project has been designed to create an anaerobic environment for the degradation of HE materials. The first step in this project, initial characterization of the test area, was conducted and is the subject of this report. The levels of HE compounds found in the samples from the test area were higher than the EPA Method 8330 was able to extract without subsequent re-precipitation; therefore, a new method was developed using a superior extractant system. The test area sampling design was relatively simple as one might expect in an initial characterization. A total of 60 samples were each removed to a depth of 4 inches using a 1 inch diameter corer. The samples were spaced at relatively even intervals across a 20 foot cross-section through the middle of four 7-foot-long adjacent plots which are designed to be a part of an in situ bioremediation experiment. Duplicate cores were taken from each location for HE extraction and analysis in order to demonstrate and measure the heterogeneity of the contamination. Each soil sample was air dried and ball-milled to provide a homogeneous solid for extraction and analysis. Several samples had large consolidated pieces of what appeared to be solid HE. These were not ball-milled due to safety concerns, but were dissolved and the solutions were analyzed. The new extraction method was superior in that results obtained for several of the contaminants were up to 20 times those obtained with the EPA extraction method. The

  18. Safety Guidelines for Laser Illumination on Exposed High Explosives and Metals in Contact with High Explosives with Calculational Results

    SciTech Connect

    Benterou, J; Roeske, F; Wilkins, P; Carpenter, K H

    2002-04-17

    Experimental tests have been undertaken to determine safe levels of laser exposure on bare high explosive (HE) samples and on common metals used in intimate contact with HE. Laser light is often focused on bare HE and upon metals in contact with HE during alignment procedures and experimental metrology experiments. This paper looks at effects caused by focusing laser beams at high energy densities directly onto the surface of various bare HE samples. Laser energy densities (fluence) exceeding 19 kilowatts/cm{sup 2} using a 5-milliwatt, 670 nm, cw laser diode were generated by focusing the laser down to a spot size diameter of 4 microns. Upon careful inspection, no laser damage was observed in any of the HE samples illuminated at this fluence level. Direct laser exposure of metals directly contacting HE surfaces was also tested. Laser energy densities (fluence) varying from 188 Watts/cm{sup 2} to 12.7 KW/cm{sup 2} were generated using an 11-Watt, 532 nm frequency-doubled Nd:YAG cw laser with focal spot size diameters as small as 100 microns. These measurements look at the temperature rise of the surface of the metal in contact with HE when laser energy is incident on the opposite side of the metal. The temperature rise was experimentally measured as a function of incident laser power, spot size, metal composition and metal thickness. Numerical simulations were also performed to solve the two-dimensional heat flow problem for this experimental geometry. In order to simplify the numerical simulation to allow representation of a large number of physical cases, the equations used in the simulation are expressed in terms of dimensionless variables. The normalized numerical solutions are then compared to the various experimental configurations utilized. Calculations and experiment agree well over the range measured. Safety guidelines for alignment laser illumination upon bare HE are outlined.

  19. Insensitive explosive

    SciTech Connect

    Lee, Kien-yin; Storm, C.B.

    1991-12-31

    This invention relates to the field of chemistry and, more particularly, to explosives. This invention is the result of a contract with the Department of Energy (Contract No. W-7405-ENG-36). It is desirable to use explosives in weapons and other applications which are less sensitive than the common explosives RDX, TNT, and HMX, since there have been catastrophic explosions of munitions which use these compounds. In preliminary characterization and sensitivity testing, it has been found that 3-amino-5-nitro-1,2,4-triazole (ANTA) is a promising insensitive high explosive. This report details the safety, production, and physical properties of ANTA.

  20. Observed high-altitude pressure waves from an underground and a surface explosion

    SciTech Connect

    Banister, J.R.; Hereford, W.V. )

    1991-03-20

    Measurements of high-altitude pressure waves from underground and surface explosions are of interest, as these waves can affect ionospheric electron density and be a source of infrasonic signals. Canisters, equipped with parachutes, were dropped from aircraft to determine time histories of pressure waves radiated by the ground surface above an underground nuclear explosion and a surface chemical explosion. These canisters contained transducers to document pressure and acceleration histories as well as a transmitter to relay information to ground receiver stations. The authors found observed pressure histories from the underground explosion to be consistent with histories calculated from surface ground motion records. The peak blast wave overpressures from the chemical explosion agreed with predicted scaled values. Observed time histories, however, had shorter positive phase duration than predicted with scaling.

  1. Observed high-altitude pressure waves from an underground and a surface explosion

    NASA Astrophysics Data System (ADS)

    Banister, John R.; Hereford, William V.

    1991-03-01

    Measurements of high-altitude pressure waves from underground and surface explosions are of interest, as these waves can affect ionospheric electron density and be a source of infrasonic signals. Canisters, equipped with parachutes, were dropped from aircraft to determine time histories of pressure waves radiated by the ground surface above an underground nuclear explosion and a surface chemical explosion. These canisters contained transducers to document pressure and acceleration histories as well as a transmitter to relay information to ground receiver stations. We found observed pressure histories from the underground explosion to be consistent with histories calculated from surface ground motion records. The peak blast wave overpressures from the chemical explosion agreed with predicted scaled values. Observed time histories, however, had shorter positive phase duration than predicted with scaling.

  2. Biodegradation of high explosives on granular activated carbon [GAC]: Enhanced desorption of high explosives from GAC -- Batch studies

    SciTech Connect

    Morley, M.C.; Speitel, G.E. Jr.

    1999-03-01

    Adsorption to GAC is an effective method for removing high explosives (HE) compounds from water, but no permanent treatment is achieved. Bioregeneration, which treats adsorbed contaminants by desorption and biodegradation, is being developed as a method for reducing GAC usage rates and permanently degrading RDX and HMX. Because desorption is often the limiting mass transfer mechanism in bioregeneration systems, several methods for increasing the rate and extent of desorption of RDX and HMX are being studied. These include use of cosolvents (methanol and ethanol), surfactants (both anionic and nonionic), and {beta}- and {gamma}-cyclodextrins. Batch experiments to characterize the desorption of these HEs from GAC have been completed using Northwestern LB-830, the GAC being used at Pantex. Over a total of 11 days of desorption, about 3% of the adsorbed RDX was desorbed from the GAC using buffered water as the desorption fluid. In comparison, about 96% of the RDX was extracted from the GAC by acetonitrile over the same desorption period. Ethanol and methanol were both effective in desorbing RDX and HMX; higher alcohol concentrations were able to desorb more HE from the GAC. Surfactants varied widely in their abilities to enhance desorption of HEs. The most effective surfactant that was studied was sodium dodecyl sulfate (SDS), which desorbed 56.4% of the adsorbed RDX at a concentration of 500 mg SDS/L. The cyclodextrins that were used were marginally more effective than water. Continuous-flow column tests are underway for further testing the most promising of these methods. These results will be compared to column experiments that have been completed under baseline conditions (using buffered water as the desorption fluid). Results of this research will support modeling and design of further desorption and bioregeneration experiments.

  3. Optically measured explosive impulse

    NASA Astrophysics Data System (ADS)

    Biss, Matthew M.; McNesby, Kevin L.

    2014-06-01

    An experimental technique is investigated to optically measure the explosive impulse produced by laboratory-scale spherical charges detonated in air. Explosive impulse has historically been calculated from temporal pressure measurements obtained via piezoelectric transducers. The presented technique instead combines schlieren flow visualization and high-speed digital imaging to optically measure explosive impulse. Prior to an explosive event, schlieren system calibration is performed using known light-ray refractions and resulting digital image intensities. Explosive charges are detonated in the test section of a schlieren system and imaged by a high-speed digital camera in pseudo-streak mode. Spatiotemporal schlieren intensity maps are converted using an Abel deconvolution, Rankine-Hugoniot jump equations, ideal gas law, triangular temperature decay profile, and Schardin's standard photometric technique to yield spatiotemporal pressure maps. Temporal integration of individual pixel pressure profiles over the positive pressure duration of the shock wave yields the explosive impulse generated for a given radial standoff. Calculated explosive impulses are shown to exhibit good agreement between optically derived values and pencil gage pressure transducers.

  4. High explosive safety manual. Final technical report, September 1978-May 1980

    SciTech Connect

    Albaugh, L.R.; McBride, D.A.

    1980-06-01

    A Safety Manual for High Explosive Processing, Handling, and Testing has been prepared for the Department of Energy. Background on the preparation and recommendations for manual implementation and augmentation are provided. The Manual is provided as a separate document.

  5. The ion mobility spectrometer for high explosive vapor detection

    SciTech Connect

    Cohen, M.J.; Stimac, R.M.; Wernlund, R.F.

    1984-07-01

    The Phemto-Chem /SUP R/ Model 100 Ion Mobility Spectrometer (IMS) operates in air and measures a number of explosive vapors at levels as low as partsper-trillion in seconds. The theory and operation of this instrument is discussed. The IMS inhales the vapor sample in a current of air and generates characteristic ions which are separated by time-of -ion drift in the atmospheric pressure gas. Quantitative results, using a dilution tunnel and standard signal generator with TNT, nitroglycerine, ethylene glycol dinitrate, cyclohexanone, methylamine, octafluoronaphthalene and hexafluorobenzene, are given. Rapid sample treatment with sample concentrations, microprocessor signal readout and chemical identification, offer a realistic opportunity of rapid explosive vapor detection at levels down to 10/sup -14/ parts by volume in air.

  6. Human Health and Ecological Risk Assessment for the Operation of the Explosives Waste Treatment Facility at Site 300 of the Lawrence Livermore National Laboratory Volume 1: Report of Results

    SciTech Connect

    Gallegos, G; Daniels, J; Wegrecki, A

    2006-04-24

    This document contains the human health and ecological risk assessment for the Resource Recovery and Conservation Act (RCRA) permit renewal for the Explosives Waste Treatment Facility (EWTF). Volume 1 is the text of the risk assessment, and Volume 2 (provided on a compact disc) is the supporting modeling data. The EWTF is operated by the Lawrence Livermore National Laboratory (LLNL) at Site 300, which is located in the foothills between the cities of Livermore and Tracy, approximately 17 miles east of Livermore and 8 miles southwest of Tracy. Figure 1 is a map of the San Francisco Bay Area, showing the location of Site 300 and other points of reference. One of the principal activities of Site 300 is to test what are known as ''high explosives'' for nuclear weapons. These are the highly energetic materials that provide the force to drive fissionable material to criticality. LLNL scientists develop and test the explosives and the integrated non-nuclear components in support of the United States nuclear stockpile stewardship program as well as in support of conventional weapons and the aircraft, mining, oil exploration, and construction industries. Many Site 300 facilities are used in support of high explosives research. Some facilities are used in the chemical formulation of explosives; others are locations where explosive charges are mechanically pressed; others are locations where the materials are inspected radiographically for such defects as cracks and voids. Finally, some facilities are locations where the machined charges are assembled before they are sent to the on-site test firing facilities, and additional facilities are locations where materials are stored. Wastes generated from high-explosives research are treated by open burning (OB) and open detonation (OD). OB and OD treatments are necessary because they are the safest methods for treating explosives wastes generated at these facilities, and they eliminate the requirement for further handling and

  7. Characterization of high-explosive initiation and safety at Los Alamos

    SciTech Connect

    McAfee, J.M.

    1994-10-01

    The Chapman-Jouget and ZND models of steady detonation have proved most useful for engineering estimation of the propagation of near-planar, steady detonation in short-reaction-zone explosives. However, even in well characterized systems, the purposeful initiation of detonation is not described by these models. The highly divergent and microscopic nature of point initiation require discerning experiments, modeling, and theoretical analysis. Recently, safety considerations in complex or damaged systems, possibly containing long-reaction-zone (insensitive) high explosives, have dominated the author`s thinking. These situations are rarely planar or steady, the physical state of the explosive may not be easily characterized, and there is a wide range of potential stimuli. The high-explosive reaction may range from none, to deflagration, to partial detonation, or to full detonation. Techniques and data applicable to estimating the level of response are needed.

  8. Los Alamos experimental capabilities: Ancho Canyon high explosives and pulse power facilities

    SciTech Connect

    Morris, C.E.

    1993-02-01

    This document outlines the Ancho Canyon testing facility comprehensive material characterization capabilities. These include the high explosive (HE) firing sites, a full complement of gun facilities, and variety of pulse power capacitor bank systems of various energies. The explosive fabrication capability at Los Alamos allows the design and testing of unique HE experimental assemblies. Depending on the hydrodynamic requirements, these explosive systems can vary widely in cost. Years of experience have enabled the development of a comprehensive set of diagnostics to monitor these experiments.

  9. Los Alamos experimental capabilities: Ancho Canyon high explosives and pulse power facilities

    SciTech Connect

    Morris, C.E.

    1993-01-01

    This document outlines the Ancho Canyon testing facility comprehensive material characterization capabilities. These include the high explosive (HE) firing sites, a full complement of gun facilities, and variety of pulse power capacitor bank systems of various energies. The explosive fabrication capability at Los Alamos allows the design and testing of unique HE experimental assemblies. Depending on the hydrodynamic requirements, these explosive systems can vary widely in cost. Years of experience have enabled the development of a comprehensive set of diagnostics to monitor these experiments.

  10. Automated detection of fingerprint traces of high explosives using ultraviolet Raman spectroscopy.

    PubMed

    Jander, Peter; Noll, Reinhard

    2009-05-01

    Ultraviolet (UV) resonance Raman spectroscopy is a promising technique for the detection of trace explosives. For real-world applications, it is necessary to develop data evaluation algorithms that automatically recognize the spectral features of explosives in a sample spectrum. We have developed a robust algorithm that can tolerate high levels of fluorescence background. We successfully demonstrated the detection of traces of ANFO and TNT explosives at surface coverage levels of 55 microg/cm(2) in a blind test experiment. The sensitivity and selectivity is discussed in terms of receiver operating characteristics (ROC) curves.

  11. Discriminating ripple-fire explosions with high frequency (>20 Hz) data

    SciTech Connect

    Carr, D.B.; Garbin, H.D.

    1996-04-01

    With a Comprehensive Test Ban (CTB), discriminating ripple-fired explosions from mining operations becomes important. Different methods have been proposed to discriminate these explosions, most of which use the modulations seen in the spectra of ripple-fired blasts. The Deployable Seismic Verification System (DSVS) in Wyoming records data at frequencies up to 50 Hz, and provides an opportunity to determine if there are any operational benefits to discriminate ripple-fired explosions from using high frequency (> 20 Hz) data. We collected a database of 646 events consisting of 118 known earthquakes, 1 known rockburst, 176 known ripple-fired quarry blasts and 351 unknown signals. Binary spectrograms for each event were calculated using a 2.5 second window, 5/8 overlap and 10% cosine window. We used a frequency band of 0 to 50 Hz. A blind test was done to choose events that appeared to have spectral banding indicative of ripple-fire explosions. One hundred fifty one events were picked as ripple-fire explosions by both authors; 59 of these events are known quarry blasts. To remove the ambiguities introduced using human analysts, we calculated an average binary spectrum for each event following a method similar to Wuster (1993). A criterion was developed so that events with six or more peaks over 0.8 and/or nulls under 0.2 was declared a ripple-fire explosion. With this method, 251 events were chosen as ripple-fire explosions, 91 of them known quarry blasts.

  12. Role of explosive instabilities in high-β disruptions in tokamaks

    NASA Astrophysics Data System (ADS)

    Aydemir, A. Y.; Lee, H. H.; Lee, S. G.; Seol, J.; Park, B. H.; In, Y. K.

    2016-05-01

    Intrinsically explosive growth of a ballooning finger is demonstrated in nonlinear magnetohydrodynamic calculations of high-β disruptions in tokamaks. The explosive finger is formed by an ideally unstable n  =  1 mode, dominated by an m/n  =  2/1 component. The quadrupole geometry of the 2/1 perturbed pressure field provides a generic mechanism for the formation of the initial ballooning finger and its subsequent transition from exponential to explosive growth, without relying on secondary processes. The explosive ejection of the hot plasma from the core and stochastization of the magnetic field occur on Alfvénic time scales, accounting for the extremely fast growth of the precursor oscillations and the rapidity of the thermal quench in some high-β disruptions.

  13. Hot-spot contributions in shocked high explosives from mesoscale ignition models

    NASA Astrophysics Data System (ADS)

    Levesque, G.; Vitello, P.; Howard, W. M.

    2013-06-01

    High explosive performance and sensitivity is strongly related to the mesoscale defect densities. Bracketing the population of mesoscale hot spots that are active in the shocked ignition of explosives is important for the development of predictive reactive flow models. By coupling a multiphysics-capable hydrodynamics code (ale3d) with a chemical kinetics solver (cheetah), we can parametrically analyze different pore sizes undergoing collapse in high pressure shock conditions with evolving physical parameter fields. Implementing first-principles based decomposition kinetics, burning hot spots are monitored, and the regimes of pore sizes that contribute significantly to burnt mass faction and those that survive thermal conduction on the time scales of ignition are elucidated. Comparisons are drawn between the thermal explosion theory and the multiphysics models for the determination of nominal pore sizes that burn significantly during ignition for the explosive 1,3,5-triamino-2,4,6-trinitrobenzene.

  14. Microbiological changes during bioremediation of explosives-contaminated soils in laboratory and pilot-scale bioslurry reactors.

    SciTech Connect

    Fuller, M. E.; Manning, J. F., Jr.; Environmental Research

    2004-01-01

    Changes in the microbial community during bioremediation of explosives-contaminated soil in a molasses-fed bioslurry process were examined. Upon addition of molasses to laboratory-scale reactors, total culturable heterotrophs increased rapidly by three to four orders of magnitude. However, heat-shocked heterotrophs and the percentage of gram-positive bacterial isolates did not increase until the soluble concentrations of 2,4,6-trinitrotoluene (TNT) and 2,4,6-trinitrobenzene (TNB) began to decrease. The number of identified phospholipid fatty acids (PLFA) and the total PLFA concentration also exhibited an immediate increase in response to molasses addition, while the concentration of branched PLFA, indicative of the gram-positive population, remained low until soluble TNT and TNB concentrations had significantly decreased. This same general relationship between explosives degradation and gram-positive-specific PLFA was observed during an experiment with a large field-scale bioslurry lagoon reactor. These results indicate that the gram-positive organisms, which have been shown to be severely impacted by even low concentrations of TNT and TNB [Current Microbiol. 35 (1997) 77; Environ. Toxicol. Chem. 17 (1998) 2185], are able to increase in concentrations after explosives compounds are reduced to non-inhibitory levels, and should therefore be able to reestablish themselves in remediated soils.

  15. Precompression and desensitization of a high explosive by trapped gas in plate impacts--new measurements

    SciTech Connect

    Anderson, W. W.; Fritz, J. N.; Kennedy, J. E.; Shaw, S. M.

    2002-01-01

    It has long been known that trapped gas between an impactor and high explosive will precompress a layer of the explosive. Most quantitative studies measure the resulting decrease in shock sensitivity. There have been no studies really aimed at measuring the properties of the precompressed layer. Experiments at Los Alamos originally to study release behavior allow the layer to be probed in PBX 9502 (95% TATB, 5% KeI-F 800).

  16. Pressure loading of aluminum and quartz using spray deposited light-initiated high explosive

    SciTech Connect

    Benham, R. A.

    1980-02-01

    A series of experiments was conducted for the purpose of evaluating the impulsive pressure loading generated at a material surface by the detonation of light-initiated high explosive on that surface. The explosive was sprayed and then detonated directly on both carbon and quartz pressure transducers. The output was recorded to allow determination of the characteristics of the pressure loading, as well as to evaluate the variability of this loading.

  17. Problems in initiating detonation of disruptive explosives by a high-intensity electron beam

    NASA Astrophysics Data System (ADS)

    Morozov, V. A.; Savenkov, G. G.; Bragin, V. A.; Kats, V. M.; Lukin, A. A.

    2012-05-01

    Experiments on initiating detonation in disruptive explosives by a nanosecond high-intensity electron beam are considered. It is shown using elementary computational estimates that the critical conditions for initiating detonation in a disruptive explosive are not satisfied for the beam parameters described here. The results of experiments on the action of a pulsed electron beam on paraffin and wax model samples are considered. It is shown that the main factor acting on the samples is the cathode plasma torch.

  18. Laboratory and field experiments used to identify Canis lupus var. familiaris active odor signature chemicals from drugs, explosives, and humans.

    PubMed

    Lorenzo, Norma; Wan, TianLang; Harper, Ross J; Hsu, Ya-Li; Chow, Michael; Rose, Stefan; Furton, Kenneth G

    2003-08-01

    This paper describes the use of headspace solid-phase microextraction (SPME) combined with gas chromatography to identify the signature odors that law enforcement-certified detector dogs alert to when searching for drugs, explosives, and humans. Background information is provided on the many types of detector dog available and specific samples highlighted in this paper are the drugs cocaine and 3,4-methylenedioxy- N-methylamphetamine (MDMA or Ecstasy), the explosives TNT and C4, and human remains. Studies include the analysis and identification of the headspace "fingerprint" of a variety of samples, followed by completion of double-blind dog trials of the individual components in an attempt to isolate and understand the target compounds that dogs alert to. SPME-GC/MS has been demonstrated to have a unique capability for the extraction of volatiles from the headspace of forensic specimens including drugs and explosives and shows great potential to aid in the investigation and understanding of the complicated process of canine odor detection. Major variables evaluated for the headspace SPME included fiber chemistry and a variety of sampling times ranging from several hours to several seconds and the resultant effect on ratios of isolated volatile components. For the drug odor studies, the CW/DVB and PDMS SPME fibers proved to be the optimal fiber types. For explosives, the results demonstrated that the best fibers in field and laboratory applications were PDMS and CW/DVB, respectively. Gas chromatography with electron capture detector (GC/ECD) and mass spectrometry (GC/MS) was better for analysis of nitromethane and TNT odors, and C-4 odors, respectively. Field studies with detector dogs have demonstrated possible candidates for new pseudo scents as well as the potential use of controlled permeation devices as non-hazardous training aids providing consistent permeation of target odors.

  19. Particle size analysis of prepared solutions and fingerprint deposits of high explosive materials

    SciTech Connect

    Carmack, W.J.; Hembree, P.B.

    1998-03-01

    The Idaho National Engineering and Environmental Laboratory (INEEL) managed and operated by Lockheed Martin Idaho Technologies Company (LMITCO) was tasked via the Federal Aviation Administration (FAA) and US Department of Energy (DOE) to conduct various studies involving the detection and measurement of explosive materials and their associated residues. This report details the results of an investigation to determine the particle size characteristics of the explosive materials used in the design, development, and testing of trace explosives detection systems. These materials, in the form of water suspensions of plastic explosives, are used to provide a quantitative means of monitoring the performance characteristics of the detection systems. The purpose of this investigation is to provide data that allows a comparison between the particles deposited using the suspension standards and the particles deposited from fingerprints. This information may support the development of quality control aids, measurement methods, or performance criteria specifications for the use of trace explosives detection systems. For this report, particle size analyses were completed on explosives standard suspensions/solutions for composition C-4, Semtex-H, and Detasheet and fingerprints for C-4, Detasheet, and pentolite. Because of the difficulty in collecting microscopic images of the particles in the suspensions from test protocol surfaces, this paper discusses the characteristics of the particles as they are found on metal, glass, and paper. The results of the particle characterization analyses indicate that the water suspensions contain particulate composed of binder materials and dissolved portions of the explosive compounds. Upon drying of the water suspensions, significant particle nucleation and growth is observed. The nucleated particulate is comparable to the particulate deposited by fingerprints.

  20. Strategies for the disposition of high explosives resulting from dismantlement of nuclear weapons

    SciTech Connect

    Pruneda, C.; Humphrey, J.

    1993-03-01

    Many thousands of pounds of high quality main-charge explosives will result as surplus from the dismantlement of returns from the US nuclear weapons stockpile. The method most often employed for dealing with this surplus explosive is destruction by open burning. However, open burning as a means of treating excess explosives is losing favor because of environmental concerns associated with such an uncontrolled thermal destruction process. Thus, alternative processes for treatment of excess explosives from weapon dismantlement is discussed. These alternatives include: reformulation, crystalline component recovery, chemical conversion of the crystalline component to higher value products which may have civilian or military applications and, when necessary, treatment as waste in an environmentally benign fashion.

  1. Composting of soils/sediments and sludges containing toxic organics including high energy explosives. Final report

    SciTech Connect

    Doyle, R.C.; Kitchens, J.F.

    1993-07-01

    Laboratory and pilot-scale experimentation were conducted to evaluate composting as an on-site treatment technology to remediate soils contaminated with hazardous waste at DOE`s PANTEX Plant. Suspected contaminated sites within the PANTEX Plant were sampled and analyzed for explosives, other organics, and inorganic wastes. Soils in drainage ditches and playas at PANTEX Plant were found to be contaminated with low levels of explosives (including RDX, HMX, PETN and TATB). Additional sites previously used for solvent disposal were heavily contaminated with solvents and transformation products of the solvent, as well as explosives and by-products of explosives. Laboratory studies were conducted using {sup 14}C-labeled explosives and {sup 14}C-labeled diacetone alcohol contaminated soil loaded into horse manure/hay composts at three rates: 20, 30, and 40%(W/W). The composts were incubated for six weeks at approximately 60{degree}C with continuous aeration. All explosives degraded rapidly and were reduced to below detection limits within 3 weeks in the laboratory studies. {sup 14}C-degradates from {sup 14}C-RDX, {sup 14}C-HMX and {sup 14}C-TATB were largely limited to {sup 14}CO{sub 2} and unextracted residue in the compost. Volatile and non-volatile {sup 14}C-degradates were found to result from {sup 14}C-PETN breakdown, but these compounds were not identified. {sup 14}C-diacetone alcohol concentrations were significantly reduced during composting. However, most of the radioactivity was volatilized from the compost as non-{sup 14}CO{sub 2} degradates or as {sup 14}C-diacetone alcohol. Pilot scale composts loaded with explosives contaminated soil at 30% (W/W) with intermittent aeration were monitored over six weeks. Data from the pilot-scale study generally was in agreement with the laboratory studies. However, the {sup 14}C-labeled TATB degraded much faster than the unlabeled TATB. Some formulations of TATB may be more resistant to composting activity than others.

  2. Hydrogen Cylinder Storage Array Explosion Evaluations at the High Flux Isotope Reactor

    SciTech Connect

    Cook, David Howard; Griffin, Frederick P; Hyman III, Clifton R

    2010-01-01

    The safety analysis for a recently-installed cold neutron source at the High Flux Isotope Reactor (HFIR) involved evaluation of potential explosion consequences from accidental hydrogen jet releases that could occur from an array of hydrogen cylinders. The scope of the safety analysis involved determination of the release rate of hydrogen, the total quantity of hydrogen assumed to be involved in the explosion, the location of an ignition point or center of the explosion from receptors of interest, and the peak overpressure at the receptors. To evaluate the total quantity of hydrogen involved in the explosion, a 2D model was constructed of the jet concentration and a radial-axial integral over the jet cloud from the centerline to the flammability limit of 4% was used to determine the hydrogen mass to be used as a source term. The location of the point source was chosen as the peak of the jet centerline concentration profile. Consequences were assessed using a combination of three methods for estimating local overpressure as a function of explosion source strength and distance: the Baker-Strehlow method, the TNT-equivalence method, and the TNO method. Results from the explosions were assessed using damage estimates in screening tables for buildings and industrial equipment.

  3. High methane natural gas/air explosion characteristics in confined vessel.

    PubMed

    Tang, Chenglong; Zhang, Shuang; Si, Zhanbo; Huang, Zuohua; Zhang, Kongming; Jin, Zebing

    2014-08-15

    The explosion characteristics of high methane fraction natural gas were investigated in a constant volume combustion vessel at different initial conditions. Results show that with the increase of initial pressure, the peak explosion pressure, the maximum rate of pressure rise increase due to a higher amount (mass) of flammable mixture, which delivers an increased amount of heat. The increased total flame duration and flame development time result as a consequence of the higher amount of flammable mixture. With the increase of the initial temperature, the peak explosion pressures decrease, but the pressure increase during combustion is accelerated, which indicates a faster flame speed and heat release rate. The maximum value of the explosion pressure, the maximum rate of pressure rise, the minimum total combustion duration and the minimum flame development time is observed when the equivalence ratio of the mixture is 1.1. Additionally, for higher methane fraction natural gas, the explosion pressure and the maximum rate of pressure rise are slightly decreased, while the combustion duration is postponed. The combustion phasing is empirically correlated with the experimental parameters with good fitting performance. Furthermore, the addition of dilute gas significantly reduces the explosion pressure, the maximum rate of pressure rise and postpones the flame development and this flame retarding effect of carbon dioxide is stronger than that of nitrogen.

  4. High methane natural gas/air explosion characteristics in confined vessel.

    PubMed

    Tang, Chenglong; Zhang, Shuang; Si, Zhanbo; Huang, Zuohua; Zhang, Kongming; Jin, Zebing

    2014-08-15

    The explosion characteristics of high methane fraction natural gas were investigated in a constant volume combustion vessel at different initial conditions. Results show that with the increase of initial pressure, the peak explosion pressure, the maximum rate of pressure rise increase due to a higher amount (mass) of flammable mixture, which delivers an increased amount of heat. The increased total flame duration and flame development time result as a consequence of the higher amount of flammable mixture. With the increase of the initial temperature, the peak explosion pressures decrease, but the pressure increase during combustion is accelerated, which indicates a faster flame speed and heat release rate. The maximum value of the explosion pressure, the maximum rate of pressure rise, the minimum total combustion duration and the minimum flame development time is observed when the equivalence ratio of the mixture is 1.1. Additionally, for higher methane fraction natural gas, the explosion pressure and the maximum rate of pressure rise are slightly decreased, while the combustion duration is postponed. The combustion phasing is empirically correlated with the experimental parameters with good fitting performance. Furthermore, the addition of dilute gas significantly reduces the explosion pressure, the maximum rate of pressure rise and postpones the flame development and this flame retarding effect of carbon dioxide is stronger than that of nitrogen. PMID:25010457

  5. A novel method for the measurement of the von Neumann spike in detonating high explosives

    NASA Astrophysics Data System (ADS)

    Sollier, A.; Bouyer, V.; Hébert, P.; Doucet, M.

    2016-06-01

    We present detonation wave profiles measured in T2 (97 wt. % TATB) and TX1 (52 wt. % TATB and 45 wt. % HMX) high explosives. The experiments consisted in initiating a detonation wave in a 15 mm diameter cylinder of explosive using an explosive wire detonator and an explosive booster. Free surface velocity wave profiles were measured at the explosive/air interface using a Photon Doppler Velocimetry system. We demonstrate that a comparison of these free surface wave profiles with those measured at explosive/window interfaces in similar conditions allows to bracket the von Neumann spike in a narrow range. For T2, our measurements show that the spike pressure lies between 35.9 and 40.1 GPa, whereas for TX1, it lies between 42.3 and 47.0 GPa. The numerical simulations performed in support to these measurements show that they can be used to calibrate reactive burn models and also to check the accuracy of the detonation products equation of state at low pressure.

  6. Project Laboratory in a High School

    ERIC Educational Resources Information Center

    Gluck, Paul

    2010-01-01

    We describe our experience in guiding a physics laboratory in the eleventh grade of a high school, in which regular laboratory classes are replaced by an experimental project carried out throughout the year. Some didactic suggestions and hints are given for those wishing to adopt such an undertaking. Outlines are given for a few of the recent…

  7. On the high fidelity simulation of chemical explosions and their interaction with solid particle clouds

    NASA Astrophysics Data System (ADS)

    Balakrishnan, Kaushik

    The flow field behind chemical explosions in multiphase environments is investigated using a robust, state-of-the-art simulation strategy that accounts for the thermodynamics, gas dynamics and fluid mechanics of relevance to the problem. Focus is laid on the investigation of blast wave propagation, growth of hydrodynamic instabilities behind explosive blasts, the mixing aspects behind explosions, the effects of afterburn and its quantification, and the role played by solid particles in these phenomena. In particular, the confluence and interplay of these different physical phenomena are explored from a fundamental perspective, and applied to the problem of chemical explosions. A solid phase solver suited for the study of high-speed, two-phase flows has been developed and validated. This solver accounts for the inter-phase mass, momentum and energy transfer through empirical laws, and ensures two-way coupling between the two phases, viz. solid particles and gas. For dense flow fields, i.e., when the solid volume fraction becomes non-negligible (˜60%), the finite volume method with a Godunov type shock-capturing scheme requires modifications to account for volume fraction gradients during the computation of cell interface gas fluxes. To this end, the simulation methodology is extended with the formulation of an Eulerian gas, Lagrangian solid approach, thereby ensuring that the so developed two-phase simulation strategy can be applied for both flow conditions, dilute and dense alike. Moreover, under dense loading conditions the solid particles inevitably collide, which is accounted for in the current research effort with the use of an empirical collision/contact model from literature. Furthermore, the post-detonation flow field consists of gases under extreme temperature and pressure conditions, necessitating the use of real gas equations of state in the multiphase model. This overall simulation strategy is then extended to the investigation of chemical explosions in

  8. Dissolution rates of three high explosive compounds: TNT, RDX, and HMX.

    PubMed

    Lynch, Jason C; Brannon, James M; Delfino, Joseph J

    2002-05-01

    Incidental exposure to high explosive compounds can cause subtle health effects to which a population could be more susceptible than injury by detonation. Proper source characterization is a key requirement in the conduct of risk assessments. For nonvolatile solid explosives, dissolution is one of the primary mechanisms that controls fate and transport, resulting in exposure to these compounds remote from their source. To date, information describing dissolution rates of high explosives has been sparse. The objective of this study was to determine the dissolution rates of three high explosive compounds, 2,4,6-trinitrotoluene (TNT), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), in dilute aqueous solutions as a function of temperature, surface area, and energy input. To determine each variable's impact on dissolution rate, experiments were performed where one variable was changed while the other two were held constant. TNT demonstrated the fastest dissolution rate followed by HMX and then RDX. Dissolution rate correlation equations were developed for each explosive compound incorporating the three aforementioned variables, independently, and collectively in one correlation equation.

  9. A working man`s analysis of incidents and accidents with explosives at the Los Alamos National Laboratory, 1946--1997

    SciTech Connect

    Ramsay, J.B.; Goldie, R.H.

    1998-12-31

    At the inception of the Laboratory hectic and intense work was the norm during the development of the atomic bombs. After the war the development of other weapons for the Cold War again contributed to an intense work environment. Formal Standard Operating Procedures (SOPs) were not required at that time. However, the occurrence of six fatalities in 1959 during the development of a new high-energy plastic bonded explosive (94% HMX) forced the introduction SOPs. After an accident at the Department of Energy (DOE) plant at Amarillo, TX in 1977, the DOE promulgated the Department wide DOE Explosives Safety Manual. Table 1 outlines the history of the introduction of SOPs and the DOE Explosives Safety Manual. Many of the rules and guidelines presented in these documents were developed and introduced as the result of an incident or accident. However, many of the current staff are not familiar with the background of the development. To preserve as much of this knowledge as possible, they are collecting documentation on incidents and accidents involving energetic materials at Los Alamos. Formal investigations of serious accidents elucidate the multiple causes that contributed to accidents. These reports are generally buried in a file and, and are not read by more recent workers. Reports involving fatalities at Los Alamos before 1974 were withheld from the general employee. Also, these documents contain much detail and analysis that is not of interest to the field worker. The authors have collected the documents describing 116 incidents and have analyzed the contributing factors as viewed from the standpoint of the individual operator. All the incidents occurred at the Los Alamos National Laboratory and involved energetic materials in some manner, though not all occurred within the explosive handling groups. Most accidents are caused by multiple contributing factors. They have attempted to select the one or two factors that they consider as the most important relative to the

  10. A verification and validation effort for high explosives at Los Alamos National Lab (u)

    SciTech Connect

    Scovel, Christina A; Menikoff, Ralph S

    2009-01-01

    We have started a project to verify and validate ASC codes used to simulate detonation waves in high explosives. Since there are no non-trivial analytic solutions, we are going to compare simulated results with experimental data that cover a wide range of explosive phenomena. The intent is to compare both different codes and different high explosives (HE) models. The first step is to test the products equation of state used for the HE models, For this purpose, the cylinder test, flyer plate and plate-push experiments are being used. These experiments sample different regimes in thermodynamic phase space: the CJ isentrope for the cylinder tests, the isentrope behind an overdriven detonation wave for the flyer plate experiment, and expansion following a reflected CJ detonation for the plate-push experiment, which is sensitive to the Gruneisen coefficient. The results of our findings for PBX 9501 are presented here.

  11. Ecological surveys of the proposed high explosives wastewater treatment facility region

    SciTech Connect

    Haarmann, T.

    1995-07-01

    Los Alamos National Laboratory (LANL) proposes to improve its treatment of wastewater from high explosives (HE) research and development activities. The proposed project would focus on a concerted waste minimization effort to greatly reduce the amount of wastewater needing treatment. The result would be a 99% decrease in the HE wastewater volume, from the current level of 6,760,000 L/mo (1,786,000 gal./mo) to 41,200 L/mo (11,000 gal./mo). This reduction would entail closure of HE wastewater outfalls, affecting some wetland areas that depend on HE wastewater effluents. The outfalls also provide drinking water for many wildlife species. Terminating the flow of effluents at outfalls would represent an improvement in water quality in the LANL region but locally could have a negative effect on some wetlands and wildlife species. None of the affected species are protected by any state or federal endangered species laws. The purpose of this report is to briefly discuss the different biological studies that have been done in the region of the project area. This report is written to give biological information and baseline data and the biota of the project area.

  12. A Statistical Hot Spot Reactive Flow Model for Shock Initiation and Detonation of Solid High Explosives

    SciTech Connect

    Nichols, A L; Tarver, C M

    2002-07-01

    A statistical hot spot reactive flow model for shock initiation and detonation of solid high explosives developed in the ALE3D hydrodynamic computer code is presented. This model is intended to evolve into a physically correct description of the physical and chemical mechanisms that control the onset of shock initiation via hotspot formation, the growth (01 failure to grow) of these hotspots into the surrounding explosive particles, the rapid transition to detonation, and self-sustaining detonation. Mesoscale modeling of the shock compression and temperature dependent chemical decomposition of individual explosive particles are currently yielding accurate predictions of hot spot formation and the subsequent growth (or failure) of these hotspot reactions in the surrounding grains. For two- and three-dimensional simulations of larger scale explosive charges, a statistical hotspot model that averages over thousands of individual hotspot dimensions and temperatures and then allows exothermic chemical reactions to grow (or fail to grow) due to thermal conduction is required. This paper outlines a first approach to constructing a probabilistic hot spot formulation based on the number density of potential hotspot sites. These hotspots can then either ignite or die out if they do not exceed certain ignition criteria, which are based on physical properties of the explosive particles. The growing hot spots spread at burn velocities given by experimentally determined deflagration velocity versus pressure relationships. The mathematics and assumptions involved in formulating the model and practical examples of its usefulness are given.

  13. High explosive spot test analyses of samples from Operable Unit (OU) 1111

    SciTech Connect

    McRae, D.; Haywood, W.; Powell, J.; Harris, B.

    1995-01-01

    A preliminary evaluation has been completed of environmental contaminants at selected sites within the Group DX-10 (formally Group M-7) area. Soil samples taken from specific locations at this detonator facility were analyzed for harmful metals and screened for explosives. A sanitary outflow, a burn pit, a pentaerythritol tetranitrate (PETN) production outflow field, an active firing chamber, an inactive firing chamber, and a leach field were sampled. Energy dispersive x-ray fluorescence (EDXRF) was used to obtain semi-quantitative concentrations of metals in the soil. Two field spot-test kits for explosives were used to assess the presence of energetic materials in the soil and in items found at the areas tested. PETN is the major explosive in detonators manufactured and destroyed at Los Alamos. No measurable amounts of PETN or other explosives were detected in the soil, but items taken from the burn area and a high-energy explosive (HE)/chemical sump were contaminated. The concentrations of lead, mercury, and uranium are given.

  14. Extrusion cast explosive

    DOEpatents

    Scribner, Kenneth J.

    1985-01-01

    Improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst are disclosed. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants.

  15. Optically detonated explosive device

    NASA Technical Reports Server (NTRS)

    Yang, L. C.; Menichelli, V. J. (Inventor)

    1974-01-01

    A technique and apparatus for optically detonating insensitive high explosives, is disclosed. An explosive device is formed by containing high explosive material in a house having a transparent window. A thin metallic film is provided on the interior surface of the window and maintained in contact with the high explosive. A laser pulse provided by a Q-switched laser is focussed on the window to vaporize the metallic film and thereby create a shock wave which detonates the high explosive. Explosive devices may be concurrently or sequentially detonated by employing a fiber optic bundle to transmit the laser pulse to each of the several individual explosive devices.

  16. HALFTON: A high-explosive containment experiment in partially saturated tuff

    SciTech Connect

    Smith, C.W.

    1996-03-01

    The HALFTON experiment explored the phenomena of high explosive detonations in 90% water-saturated tuff rock. The explosive source was a 453 kg TNT sphere which was grouted in a drift in G Tunnel, Nevada Test Site. Active gages measured stresses and motions in the range of 1.3 to 5.3 cavity radii and showed a peak stress decay as range raised to the {minus}2.77 power. Additional stress gages were fielded to investigate the gage inclusion problem.

  17. Simulating the Thermal Response of High Explosives on Time Scales of Days to Microseconds

    SciTech Connect

    Yoh, J J; McClelland, M A

    2003-07-16

    We present an overview of computational techniques for simulating the thermal cookoff of high explosives using a multi-physics hydrodynamics code, ALE3D. Recent improvements to the code have aided our computational capability in modeling the response of energetic materials systems exposed to extreme thermal environments, such as fires. We consider an idealized model process for a confined explosive involving the transition from slow heating to rapid deflagration in which the time scale changes from days to hundreds of microseconds. The heating stage involves thermal expansion and decomposition according to an Arrhenius kinetics model while a pressure-dependent burn model is employed during the explosive phase. We describe and demonstrate the numerical strategies employed to make the transition from slow to fast dynamics.

  18. High-speed photography of the first hydrogen-bomb explosion

    SciTech Connect

    Brixner, B.

    1992-01-01

    Obtaining detailed photographs of the early stages of the first hydrogen bomb explosion in 1952 posed a number of problems. First, it was necessary to invent a continuous-access camera which could solve the problem that existing million-picture-per-second cameras were blind most of the time. The solution here was to alter an existing camera design so that two modified cameras could be mounted around a single high-speed rotating mirror. A second problem, acquiring the necessary lenses of precisely specified focal lengths, was solved by obtaining a large number of production lenses from war surplus salvage. A third hurdle to be overcome was to test the new camera at an A-bomb explosion. Finally, it was necessary to solve the almost impossible difficulty of building a safe camera shelter close to a megaton explosion. This paper describes the way these problems were solved. Unfortunately the successful pictures that were taken are sill classified.

  19. High-speed photography of the first hydrogen-bomb explosion

    SciTech Connect

    Brixner, B.

    1992-09-01

    Obtaining detailed photographs of the early stages of the first hydrogen bomb explosion in 1952 posed a number of problems. First, it was necessary to invent a continuous-access camera which could solve the problem that existing million-picture-per-second cameras were blind most of the time. The solution here was to alter an existing camera design so that two modified cameras could be mounted around a single high-speed rotating mirror. A second problem, acquiring the necessary lenses of precisely specified focal lengths, was solved by obtaining a large number of production lenses from war surplus salvage. A third hurdle to be overcome was to test the new camera at an A-bomb explosion. Finally, it was necessary to solve the almost impossible difficulty of building a safe camera shelter close to a megaton explosion. This paper describes the way these problems were solved. Unfortunately the successful pictures that were taken are sill classified.

  20. Plasma-depleted holes, waves, and energized particles from high-altitude explosive plasma perturbation experiments

    NASA Technical Reports Server (NTRS)

    Wescott, E. M.; Stenbaek-Nielsen, H. C.; Hallinan, T.; Deehr, C.; Romick, J.; Olson, J.; Kelley, M. C.; Pfaff, R.; Torbert, R. B.; Newell, P.

    1985-01-01

    The results of high-explosive shaped charge experiments King Crab and Bubble Machines I and II, intended to perturb the ambient plasma and magnetic field, are discussed. The instrumentation was flown above an altitude of 460 km in March 1980 and 1981 and comprised a single-axis dipole electric field detector, a fixed bias cylindrical Langmuir probe, a three-axis attitude magnetometer, and curved plated energetic ion and electron electrostatic analyzer. Among the effects of the explosion which are detailed, emphasis is placed on the creation of an ion-depleted dark hole during the Bubble Machine II experiment; mechanisms explaining the phenomenon are outlined. The auroral intensity ion beams with energies of up to 6.8 keV, observed following the explosion in the field-aligned ion electrostatic analyzer, are suggested to represent an existing ion conic population pitch angle scattered by the released barium into the view of the detector.

  1. An Improved Reaction Rate Equation for Simulating the Ignition and Growth of Reaction in High Explosives

    SciTech Connect

    Murphy, M J

    2010-03-08

    We describe an improved reaction rate equation for simulating ignition and growth of reaction in high explosives. It has been implemented into CALE and ALE3D as an alternate to the baseline the Lee-Tarver reactive flow model. The reactive flow model treats the explosive in two phases (unreacted/reactants and reacted/products) with a reaction rate equation to determine the fraction reacted, F. The improved rate equation has fewer parameters, is continuous with continuous derivative, results in a unique set of reaction rate parameters for each explosive while providing the same functionality as the baseline rate equation. The improved rate equation uses a cosine function in the ignition term and a sine function in the growth and completion terms. The improved rate equation is simpler with fewer parameters.

  2. High-speed photography of the first hydrogen-bomb explosion

    NASA Astrophysics Data System (ADS)

    Brixner, Berlyn

    1993-01-01

    Obtaining detailed photographs of the early stages of the first hydrogen bomb explosion in 1952 posed a number of problems. First, it was necessary to invent a continuous-access camera which could solve the problem that existing million-picture-per-second cameras were blind most of the time. The solution here was to alter an existing camera design so that two modified cameras could be mounted around a single high-speed rotating mirror. A second problem, acquiring the necessary lenses of precisely specified focal lengths, was solved by obtaining a large number of production lenses from war surplus salvage. A third hurdle to be overcome was to test the new camera at an A-bomb explosion. Finally, it was necessary to solve the almost impossible difficulty of building a safe camera shelter close to a megaton explosion. This paper describes the way these problems were solved. Unfortunately the successful pictures that were taken are still classified.

  3. Characterisation and Modification of Thermally Stable High Explosives for Laser Flyer Applications

    NASA Astrophysics Data System (ADS)

    Parker, Adam; Claridge, Robert; Proud, William

    2007-06-01

    Laser initiation offers improved weapon survivability, versatility and greater IM compliance. Detonators based on laser-driven flyers are less vulnerable to electrical initiation, and can be based on insensitive secondary explosives rather than sensitive primary explosives. Additionally, this technology will offer advantages in terms of improved flexibility and reliability. Several novel energetic materials were selected for investigation at QinetiQ. The materials are of interest due to their increased thermal stability and power output over conventional explosives. These properties promote the materials as ideal candidates for use in insensitive munition compliant applications, whilst also improving performance. The response of these materials to short duration high-amplitude shock impulses by laser-driven flyers was investigated. Preparation techniques including co-crystallisation, sonication and incorporation of additives were used to sensitise the materials to flyer impact, yet maintain their insensitivity to external hazards. Hazard characterisation was performed to ensure that no detrimental effects were caused by modification.

  4. LAPTAG High School Plasma Physics laboratory

    NASA Astrophysics Data System (ADS)

    Layton, William; Gekelman, Walter; Pribyl, Patrick

    1999-11-01

    Six years ago an alliance of about thirty high schools and community colleges, and the UCLA physics department was initiated. LAPTAG (Los Angeles teachers Alliance Group) started with laboratory tours, a Web based astronomy course and a seismology project funded by the Office of the President of the University of California. Laptag has a website: [ http://coke.physics.ucla.edu/laptag] in which these projects as well as websites of the individual schools may be found. Recently we were funded by DOE to construct a plasma physics laboratory, which will reside at UCLA, but used by the high school teachers and their students. The machine is presently under construction by a team of eight high school teachers under the supervision of UCLA plasma physicists. The plasma will be generated by a helicon source, and then drift into a field free test chamber surrounded by confining permanent magnets. The preliminary experiments will be on ion acoustic waves and the mapping of the p! lasma potential. Presently we are giving the teachers a summer course in plasma Physics after which they will write a laboratory manual and lecture notes for a high school laboratory based course. In some schools this will be offered as part of an "AP" course and at others as a special laboratory. The courses will be taught by the high school teachers and offered this Fall semester. We will present pictures of the device, preliminary data, and course material.

  5. Destruction of peroxide explosives.

    PubMed

    Oxley, Jimmie C; Smith, James L; Huang, Jiaorong; Luo, Wei

    2009-09-01

    Chemicals containing multiple peroxide functionalities, such as triacetone triperoxide (TATP), diacetone diperoxide (DADP), or hexamethylene triperoxide diamine (HMTD), can be explosive. They are impractical and are not used by legitimate military groups because they are shock and heat sensitive compared to military explosives. They are attractive to terrorists because synthesis is straightforward, requiring only a few easily obtained ingredients. Physical removal of these synthesis products is highly hazardous. This paper discusses methods to degrade peroxide explosives chemically, at room temperature. A number of mixtures containing metals (e.g., zinc, copper) and metal salts (e.g., zinc sulfate, copper chloride) were found effective, some capable of destroying TATP solutions in a few hours. Strong acids proved useful against solid peroxide materials; however, on a 1 g scale, addition of concentrated sulfuric acid caused TATP to detonate. Thus, this technique should only be used to destroy small-laboratory quantities. PMID:19737243

  6. High-speed imaging, acoustic features, and aeroacoustic computations of jet noise from Strombolian (and Vulcanian) explosions

    NASA Astrophysics Data System (ADS)

    Taddeucci, J.; Sesterhenn, J.; Scarlato, P.; Stampka, K.; Del Bello, E.; Pena Fernandez, J. J.; Gaudin, D.

    2014-05-01

    High-speed imaging of explosive eruptions at Stromboli (Italy), Fuego (Guatemala), and Yasur (Vanuatu) volcanoes allowed visualization of pressure waves from seconds-long explosions. From the explosion jets, waves radiate with variable geometry, timing, and apparent direction and velocity. Both the explosion jets and their wave fields are replicated well by numerical simulations of supersonic jets impulsively released from a pressurized vessel. The scaled acoustic signal from one explosion at Stromboli displays a frequency pattern with an excellent match to those from the simulated jets. We conclude that both the observed waves and the audible sound from the explosions are jet noise, i.e., the typical acoustic field radiating from high-velocity jets. Volcanic jet noise was previously quantified only in the infrasonic emissions from large, sub-Plinian to Plinian eruptions. Our combined approach allows us to define the spatial and temporal evolution of audible jet noise from supersonic jets in small-scale volcanic eruptions.

  7. High explosive safety manual. Fifth quarterly technical progress report, October-December 1979

    SciTech Connect

    Albaugh, L.R.; McBride, D.A.

    1980-01-01

    This is the fifth quarterly technical report on a program to prepare a high explosive safety manual for the Department of Energy. The program is described and progress to date is presented. During this work period, the first draft of the manual was completed and the quantitative risk analysis begun.

  8. A Constitutive Model for Long Time Duration Mechanical Behavior in Insensitive High Explosives

    SciTech Connect

    Darnell, I M; Oh, S; Hrousis, C A; Cunningham, B J; Gagliardi, F J

    2010-03-09

    An anisotropic constitutive model for the long term dimensional stability of insensitive high explosives is proposed. Elastic, creep, thermal, and ratchet growth strains are developed. Pressure and temperature effects are considered. The constitutive model is implemented in an implicit finite element code and compared to a variety of experimental data.

  9. Development of an air cleaning system for dissolving high explosives from nuclear warheads

    SciTech Connect

    Bergman, W.; Wilson, K.; Staggs, K.; Wapman, D.

    1997-08-01

    The Department of Energy (DOE) has a major effort underway in dismantling nuclear weapons. In support of this effort we have been developing a workstation for removing the high explosive (HE) from nuclear warheads using hot sprays of dimethyl sulfoxide (DMSO) solvent to dissolve the HE. An important component of the workstation is the air cleaning system that is used to contain DMSO aerosols and vapor and radioactive aerosols. The air cleaning system consists of a condenser to liquefy the hot DMSO vapor, a demister pad to remove most of the DMSO aerosols, a high efficiency particulate air (HEPA) filter to remove the remaining aerosols, an activated carbon filter to remove the DMSO vapor, and a final HEPA filter to meet the redundancy requirement for HEPA filters in radioactive applications. The demister pad is a 4{double_prime} thick mat of glass and steel fibers and was selected after conducting screening tests on promising candidates. We also conducted screening tests on various activated carbons and found that all had a similar performance. The carbon breakthrough curves were fitted to a modified Wheeler`s equation and gave excellent predictions for the effect of different flow rates. After all of the components were assembled, we ran a series of performance tests on the components and system to determine the particle capture efficiency as a function of size for dioctyl sebacate (DOS) and DMSO aerosols using laser particle counters and filter samples. The pad had an efficiency greater than 990% for 0.1 {mu}m DMSO particles. Test results on the prototype carbon filter showed only 70% efficiency, instead of the 99.9% in small scale laboratory tests. Thus further work will be required to develop the prototype carbon filter. 7 refs., 18 figs., 10 tabs.

  10. Calculating the dynamics of High Explosive Violent Response (HEVR) after ignition

    SciTech Connect

    Reaugh, J E

    2008-10-15

    We are developing models to describe the circumstances when molecular and composite explosives undergo a rapid release of energy without detonating, and to describe the evolution of the energy release. The models also apply to the behavior of rocket propellants subject to mechanical insult, whether for accidents (Hazards) or the suite of standardized tests used to assess whether the system can be designated an Insensitive Munition (IM). In the applications described here, we are studying a UK-developed HMX (1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane) explosive, which is 91% by weight HMX and 9% binder-plasticizer. Most explosives and propellants, when subjected to a mechanical insult such as a drop or impact that is well below the threshold for detonation, have been observed to react. In some circumstances the reaction can be violent. This behavior is known as High Explosive Violent Response (HEVR). Fundamental to our model is the observation that the mechanical insult produces damage in a volume of the explosive near the trajectory of the impactor. The damage is manifest as surface area through the creation of cracks and fragments, and also as porosity through the separation of crack faces and isolation of the fragments. Open porosity permits a flame to spread easily and so ignite the newly formed surface area. The additional surface area leads to a direct increase in the mass-burning rate. As the kinetic energy and power of the insult increases, the degree of damage and the volume of damage both increase. Upon a localized ignition, the flame spreads to envelop the damaged volume, and the pressure rises at an accelerated rate until neither mechanical strength nor inertial confinement can successfully contain the pressure. The confining structure begins to expand. This reduces the pressure and may even extinguish the flame. Both the mass of explosive involved and the rate at which the gas is produced contribute to each of several different measures of violence

  11. Hydrogen Explosion Analysis for Cold Source Installation at the High Flux Isotope Reactor

    SciTech Connect

    Cook, David Howard

    2008-01-01

    Installation of a cold neutron source in the High Flux Isotope Reactor (HFIR) involved introduction of pressurized, cryogenic hydrogen into the facility and created explosion hazards to reactor safety-related equipment and personnel. Evaluation of potential hydrogen releases and facility/personnel consequences as a result of explosions was a key part of the safety analyses submitted to the DOE to obtain approval for testing and operation with hydrogen. This paper involves a description of the various hydrogen release and explosion consequence analyses that were performed. The range of explosion calculations involved (1) a detonation analysis using a 2D-transient CTH code model, (2) various BLAST/FX code models to estimate structural damage from equivalent point TNT sources, (3) a BLASTX code model to propagate shock and gas flow overpressures from a point TNT source, (4) a spreadsheet that combined a TNT-quivalence model and strong deflagration methods, and (5) a hydrogen jet model to evaluate potential high pressure jet releases.

  12. LABORATORY EXERCISES IN OCEANOGRAPHY FOR HIGH SCHOOLS.

    ERIC Educational Resources Information Center

    National Science Foundation, Washington, DC.

    DESCRIBED ARE LABORATORY EXERCISES IN OCEANOGRAPHY DEVELOPED FOR USE IN HIGH SCHOOLS BY THE SECONDARY SCHOOL TEACHERS IN THE 1967 NATIONAL SCIENCE FOUNDATION (NSF) SUMMER INSTITUTE IN OCEANOGRAPHY AT FLORIDA STATE UNIVERSITY. INCLUDED ARE SUCH ACTIVITIES AS (1) THE MEASUREMENT OF TEMPERATURE, WATER VAPOR, PRESSURE, SALINITY, DENSITY, AND OTHERS,…

  13. Infrasonic observations and modeling of the Minor Uncle High Explosive event

    SciTech Connect

    Whitaker, R.; Noel, S.D.; Meadows, W.R.

    1994-09-01

    Minor Uncle was a Department of Defense sponsored explosive test of 2440 tons of ammonium nitrate and fuel oil (ANFO) executed on June 10, 1993, at White Sands Missile Range, NM. Los Alamos National Laboratory made infrasonic observations of this event at three stations: Los Alamos, NM, 250 km range; St. George, UT, 750 km range; and the Nevada Test Site, NV, 928 km range. All three stations obtained positive results and had very low background noise levels. Data from all stations will be presented, and normal mode calculations of the wave propagation, including upper atmospheric winds, to St. George will be compared to the data.

  14. On the quantitative measurement of fracture toughness in high explosive and mock materials

    SciTech Connect

    Liu, Cheng; Cady, Carl M; Rae, Philip J; Lovato, Manuel L

    2010-01-01

    Two approaches in measuring the fracture toughness of heterogeneous high explosives and their mocks are explored in this investigation. One is the global measurement according to the ASTM E 1820-06 standard, which is primarily developed for metallic materials to obtain quantitative measurement of parameters such as the stress intensity factor, the J-integral, and the crack-tip opening displacement (CTOD). The second approach is based on local measurements using digital image correlation (DIC). Detailed results and comparisons of the two strategies will be presented for the Mock 900-21, a mechanical simulant of the PBX 9501 high explosive. Cracking is the most dominant mechanical failure mechanism in high explosives (HE) and a key parameter for describing and predicting crack initiation and extension is the fracture toughness. Quantitative measurement of such material property poses challenges, and this is mainly because that the material is highly heterogeneous with a very complicated microstructure and the contrast of the mechanical properties of the constituents is also remarkably high. In this investigation, we explore two strategies in measuring the fracture toughness of heterogeneous high explosives and their mocks. The first approach is based on the global measurement according to the ASTM E 1820-06 standard, which is primarily developed for metallic materials to obtain quantitative measurement of parameters such as the stress intensity factor, the J-integral, and the crack-tip opening displacement (CTOD). However, there are difficulties in applying the ASTM standard on energetic solids that include identifying the moment of crack initiation and pinpointing exact crack length at each instant of time. The second approach is based on local measurements. We developed a technique for quantitatively identifying the location and extent of macroscopic cracks in heterogeneous high explosive and mock material. By combining such a technique with the displacement field

  15. Response of standard and high-capacity HEPA filters to simulated tornado and explosive transients

    SciTech Connect

    Gregory, W.S.; Smith, P.R.

    1982-03-01

    An investigation was performed to determine the response of standard and high-capacity high-efficiency particulate air filters to simulated tornado and explosive transients. Most of the tests were directed toward evaluating the structural response of high-capacity filters to explosive transients. Selected tests were performed to evaluate the effects of particulate loading on filtration efficiencies. Also, several of the high-capacity filters were subjected to simulated toronado transients. The results indicate that the upper structural limits of high-capacity filters for explosive loading is 6.89-kPa (1-psi) peak pressure and 100-kPa-ms (14.51-psi-ms) impulse. These limits are below the approximately 13.78-kPa (2-psi) peak pressure loadings found for standard HEPA filters. Tests of high-capacity filters preloaded with aerosol indicated that the structural limits were further degraded by approximately 40%. The filtration efficiencies were degraded to approximately 70% when the filters were subjected to aerosol entrained within the shock pulse. The effect of simulated tornado transients on high-capacity filters resulted in an upper structural limit of 11.02 kPa (1.6 psi) for peak pressure.

  16. On the high fidelity simulation of chemical explosions and their interaction with solid particle clouds

    NASA Astrophysics Data System (ADS)

    Balakrishnan, Kaushik

    The flow field behind chemical explosions in multiphase environments is investigated using a robust, state-of-the-art simulation strategy that accounts for the thermodynamics, gas dynamics and fluid mechanics of relevance to the problem. Focus is laid on the investigation of blast wave propagation, growth of hydrodynamic instabilities behind explosive blasts, the mixing aspects behind explosions, the effects of afterburn and its quantification, and the role played by solid particles in these phenomena. In particular, the confluence and interplay of these different physical phenomena are explored from a fundamental perspective, and applied to the problem of chemical explosions. A solid phase solver suited for the study of high-speed, two-phase flows has been developed and validated. This solver accounts for the inter-phase mass, momentum and energy transfer through empirical laws, and ensures two-way coupling between the two phases, viz. solid particles and gas. For dense flow fields, i.e., when the solid volume fraction becomes non-negligible (˜60%), the finite volume method with a Godunov type shock-capturing scheme requires modifications to account for volume fraction gradients during the computation of cell interface gas fluxes. To this end, the simulation methodology is extended with the formulation of an Eulerian gas, Lagrangian solid approach, thereby ensuring that the so developed two-phase simulation strategy can be applied for both flow conditions, dilute and dense alike. Moreover, under dense loading conditions the solid particles inevitably collide, which is accounted for in the current research effort with the use of an empirical collision/contact model from literature. Furthermore, the post-detonation flow field consists of gases under extreme temperature and pressure conditions, necessitating the use of real gas equations of state in the multiphase model. This overall simulation strategy is then extended to the investigation of chemical explosions in

  17. High Temperature Materials Laboratory third annual report

    SciTech Connect

    Tennery, V.J.; Foust, F.M.

    1990-12-01

    The High Temperature Materials Laboratory has completed its third year of operation as a designated DOE User Facility at the Oak Ridge National Laboratory. Growth of the user program is evidenced by the number of outside institutions who have executed user agreements since the facility began operation in 1987. A total of 88 nonproprietary agreements (40 university and 48 industry) and 20 proprietary agreements (1 university, 19 industry) are now in effect. Sixty-eight nonproprietary research proposals (39 from university, 28 from industry, and 1 other government facility) and 8 proprietary proposals were considered during this reporting period. Research projects active in FY 1990 are summarized.

  18. Low amplitude impact testing and analysis of pristine and aged solid high explosives

    SciTech Connect

    Chidester, S K; Garza, R; Tarver, C M

    1998-08-17

    The critical impact velocities of 60.1 mm diameter blunt steel projectiles required for ignition of exothermic chemical reaction were determined for heavily confined charges of new and aged (15-30 years) solid HMX-based high explosives. The explosives in order of decreasing impact sensitivity were: PBX 9404; LX-lo; LX-14; PBX 9501; and LX-04. Embedded pressure gauges measured the interior pressure histories. Stockpile aged LX-04 and PBX 9501 from dismantled units were tested and compared to freshly pressed charges. The understanding of explosive aging on impact ignition and other hazards must improve as systems are being deployed longer than their initial estimated lifetimes. The charges that did not react on the first impact were subjected to multiple impacts. While the violence of reaction increased with impact velocity, it remained much lower than that produced by an intentional detonation. Ignition and Growth reactive flow models were developed to predict HMX-based explosive impact sensitivity in other geometries and scenarios.

  19. Shock-to-detonation transition of RDX and NTO based composite high explosives: experiments and modeling

    NASA Astrophysics Data System (ADS)

    Baudin, Gerard; Roudot, Marie; Genetier, Marc

    2013-06-01

    Composite HMX and NTO based high explosives (HE) are widely used in ammunitions. Designing modern warheads needs robust and reliable models to compute shock ignition and detonation propagation inside HE. Comparing to a pressed HE, a composite HE is not porous and the hot-spots are mainly located at the grain - binder interface leading to a different behavior during shock-to-detonation transition. An investigation of how shock-to-detonation transition occurs inside composite HE containing RDX and NTO is proposed in this lecture. Two composite HE have been studied. The first one is HMX - HTPB 82:18. The second one is HMX - NTO - HTPB 12:72:16. These HE have been submitted to plane sustained shock waves at different pressure levels using a laboratory powder gun. Pressure signals are measured using manganin gauges inserted at several distances inside HE. The corresponding run-distances to detonation are determined using wedge test experiments where the plate impact is performed using a powder gun. Both HE exhibit a single detonation buildup curve in the distance - time diagram of shock-to-detonation transition. This feature seems a common shock-to-detonation behavior for composite HE without porosity. This behavior is also confirmed for a RDX - HTPB 85:15 based composite HE. Such a behavior is exploited to determine the heterogeneous reaction rate versus the shock pressure using a method based on the Cauchy-Riemann problem inversion. The reaction rate laws obtained allow to compute both run-distance to detonation and pressure signals.

  20. Development, testing and practical use of two special containment vessels for storage and transportation of high explosives

    SciTech Connect

    Dikken, H. den

    1995-12-31

    The storage and transportation of high explosives gives many logistic managers a headache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

  1. Numerical Modeling of Impact Initiation of High Explosives

    SciTech Connect

    Wu, C J; Piggott, T; Yoh, J; Reaugh, J

    2006-05-31

    We performed continuum mechanics simulations to examine the behavior of energetic materials in Ballistic Chamber Impact (BIC) experiments, using an Arbitrary Lagrangian-Eulerian code (ALE3D). Our simulations revealed that interface friction plays an important role in inducing the formation of shear bands, which result in 'hot spots' for ignition. The temperature localization during BIC impact was found to be significant in materials with high yield strength. In those materials, there are multiple locations inside shear bands can achieve temperatures exceeding the threshold temperature for reaction. In addition, we investigated the relevant parameters influencing the pressure profile of a BIC test by numerical analysis from a simple phenomenological model. To our surprise, we found that the peaks of BIC pressure profiles not only can be a result of multi-center chemical reactions, but can also arise from factors associated apparatus configuration.

  2. Modeling thermally driven energetic response of high explosives

    SciTech Connect

    Couch, R; McCallen, R C; Nichols III, A L; Otero, I; Sharp, R

    1998-08-17

    We have improved our ability to model the response of energetic materials to thermal stimuli and the processes involved in the energetic response. Traditionally, the analyses of energetic materials have involved coupled thermal transport/chemical reaction codes. This provides only a reasonable estimate of the time and location of ensuing rapid reaction. To predict the violence of the reaction, the mechanical motion must be included in the wide range of time scales associated with the thermal hazard. The ALE3D code has been modified to assess the hazards associated with heating energetic materials in weapons by coupling to thermal transport model and chemistry models. We have developed an implicit time step option to efficiently and accurately compute the hours of heating to reaction of the energetic material. Since, on these longer time scales materials can be expected to have significant motion, it is even more important to provide high-order advection for all components, including the chemical species. We show two examples of coupled thermal/mechanical/chemical models of energetic materials in thermal environments.

  3. Modeling thermally driven energetic response of high explosives

    SciTech Connect

    Sharp, R; Couch, R; McCallen, R C; Nichols III, A L; Otero, I

    1998-02-01

    We have improved our ability to model the response of energetic materials to thermal stimuli and the processes involved in the energetic response. Traditionally, the analyses of energetic materials have involved coupled thermal transport/chemical reaction codes. This provides only a reasonable estimate of the time and location of ensuing rapid reaction. To predict the violence of the reaction, the mechanical motion must be included in the wide range of time scales associated with the thermal hazard. The ALE3D code has been modified to assess the hazards associated with heating energetic materials in weapons by coupling to thermal transport model and chemistry models. We have developed an implicit time step option to efficiently and accurately compute the hours of heating to reaction of the energetic material. Since, on these longer time scales materials can be expected to have significant motion, it is even more important to provide high-order advection for all components, including the chemical species. We show two examples of coupled thermal/mechanical/chemical models of energetic materials in thermal environments.

  4. Progress in model development to quantify High Explosive Violent Response (HEVR) to mechancial insult

    SciTech Connect

    Reaugh, J E

    2008-07-29

    The rapid release of chemical energy has found application for industrial and military purposes since the invention of gunpowder. Black powder, smokeless powder of various compositions, and pyrotechnics all exhibit the rapid release of energy without detonation when they are being used as designed. The rapidity of energy release for these materials is controlled by adjustments to the particle surface area (propellant grain configuration or powder particle size) in conjunction with the measured pressure-dependent burning rate, which is very subsonic. In this way a manufacturing process can be used to engineer the desired violence of the explosion. Detonations in molecular explosives, in contrast, propagate with a supersonic velocity that depends on the loading density, but is independent of the surface area. In ideal detonations, the reaction is complete within a small distance of the propagating shock front. Non-ideal detonations in molecular and composite explosives proceed with a slower velocity, and the reaction may continue well behind the shock front. We are developing models to describe the circumstances when molecular and composite explosives undergo a rapid release of energy without detonating. The models also apply to the behavior of rocket propellants subject to mechanical insult, whether for accidents (Hazards) or the suite of standardized tests used to assess whether the system can be designated an Insensitive Munition (IM). In the application described here, we are studying an HMX (1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane) explosive developed in the UK, which is 91% by weight HMX and 9% binder-plasticizer. Most explosives and propellants, when subjected to a mechanical insult, drop or impact that is well below the threshold for detonation have been observed to react violently. This behavior is known as High Explosive Violent Reaction (HEVR). The basis of our model is the observation that the mechanical insult produces damage in a volume of the

  5. Single and multiple impact ignition of new and aged high explosives in the Steven Impact Test

    SciTech Connect

    Chidester, S K; DePiero, A H; Garza, R G; Tarver, C M

    1999-06-01

    Threshold impact velocities for ignition of exothermic reaction were determined for several new and aged HMX-based solid high explosives using three types of projectiles in the Steven Test. Multiple impact threshold velocities were found to be approximately 10% lower in damaged charges that did not react in one or more prior impacts. Projectiles with protrusions that concentrate the friction work in a small volume of explosive reduced the threshold velocities by approximately 30%. Flat projectiles required nearly twice as high velocities for ignition as rounded projectiles. Blast overpressure gauges were used for both pristine and damaged charges to quantitatively measure reaction violence. Reactive flow calculations of single and multiple impacts with various projectiles suggest that the ignition rates double in damaged charges.

  6. Implementation of a High Explosive Equation of State into an Eulerian Hydrocode

    NASA Astrophysics Data System (ADS)

    Littlefield, David L.; Baker, Ernest L.

    2004-07-01

    The implementation of a high explosive equation of state into the Eulerian hydrocode CTH is described. The equation of state is an extension to JWL referred to as JWLB, and is intended to model the thermodynamic state of detonation products from a high explosive reaction. The EOS was originally cast in a form p = p(ρ, e), where p is the pressure, ρ is the density and e is the internal energy. However, the target application code requires an EOS of the form p = p(ρ, T), where T is the temperature, so it was necessary to reformulate the EOS in a thermodynamically consistent manner. A Helmholtz potential, developed from the original EOS, insures this consistency. Example calculations are shown that illustrate the veracity of this implementation.

  7. A Comparison of Neutron-Based Non-Destructive Assessment Methods for Chemical Warfare Material and High Explosives

    SciTech Connect

    Seabury, E. H.; Chichester, D. L.; Wharton, C. J.; Caffrey, A. J.

    2009-03-10

    Prompt Gamma Neutron Activation Analysis (PGNAA) systems employ neutrons as a probe to interrogate items, e.g. chemical warfare materiel-filled munitions. The choice of a neutron source in field-portable systems is determined by its ability to excite nuclei of interest, operational concerns such as radiological safety and ease-of-use, and cost. Idaho National Laboratory's PINS Chemical Assay System has traditionally used a {sup 252}Cf isotopic neutron source, but recently a deuterium-tritium (DT) electronic neutron generator (ENG) has been tested as an alternate neutron source. This paper presents the results of using both of these neutron sources to interrogate chemical warfare materiel (CWM) and high explosive (HE) filled munitions.

  8. Prospects of High Energy Laboratory Astrophysics

    SciTech Connect

    Ng, J.S.T.; Chen, P.; /SLAC

    2006-09-21

    Ultra high energy cosmic rays (UHECR) have been observed but their sources and production mechanisms are yet to be understood. We envision a laboratory astrophysics program that will contribute to the understanding of cosmic accelerators with efforts to: (1) test and calibrate UHECR observational techniques, and (2) elucidate the underlying physics of cosmic acceleration through laboratory experiments and computer simulations. Innovative experiments belonging to the first category have already been done at the SLAC FFTB. Results on air fluorescence yields from the FLASH experiment are reviewed. Proposed future accelerator facilities can provided unprecedented high-energy-densities in a regime relevant to cosmic acceleration studies and accessible in a terrestrial environment for the first time. We review recent simulation studies of nonlinear plasma dynamics that could give rise to cosmic acceleration, and discuss prospects for experimental investigation of the underlying mechanisms.

  9. Generation of Electric and Magnetic Fields During Detonation of High Explosive Charges in Boreholes

    SciTech Connect

    Soloviev, S; Sweeney, J

    2004-06-04

    We present experimental results of a study of electromagnetic field generation during underground detonation of high explosive charges in holes bored in sandy loam and granite. Test conditions and physico-mechanical properties of the soil exert significant influence on the parameters of electromagnetic signals generated by underground TNT charges with masses of 2 - 200 kg. The electric and magnetic field experimental data are satisfactorily described by an electric dipole model with the source embedded in a layered media.

  10. An improved technique of expanding metal ring experiment under high explosive loading.

    PubMed

    Tang, Tiegang; Ren, Guowu; Guo, Zhaoliang; Li, Qingzhong

    2013-04-01

    An experimental technique for metal expanding ring subjected to high explosive loading is conducted to significantly improve the loading stability compared with the traditional setup of two-end detonator initiation. Aspects of the circuit design, experimental arrangement, and initiation principle are illustrated in great detail. In terms of this experimental platform, we examine the velocity response of an individual ring, which demonstrates the experimental reproducibility. Moreover, fragmentation of multiple rings stacked on a metal driver is discussed.

  11. A legacy of the ""megagoule committee,"" thirty years of explosive pulsed power research and development at Los Alamos National Laboratory

    SciTech Connect

    Goforth, James H; Oona, Henn; Herrera, Dennis H; Torres, David T; Tasker, D. G.; Meyer, R. K.; Atchison, W. L.; Rousculp, C. L.; Reinovsky, R. E.; Sheppard, M.; Turchi, P. J.; Watt, R. G.

    2010-10-29

    In 1980, Los Alamos formed the 'Megajoule Committee' with the expressed goal of developing a one Megajoule plasma radiation source. The ensuing research and development has given rise to a wide variety of high explosive pulsed power accomplishments, and there is a continuous stream of work that continues to the present. A variety of flux compression generators (FCGs or generators) have been designed and tested, and a number of pulse shortening schemes have been investigated. Supporting computational tools have been developed in parallel with experiments. No fewer that six unique systems have been developed and used for experiments. This paper attempts to pull together the technical details, achievements, and wisdom amassed during the intervening thirty years, and notes how we would push for increased performance in the future.

  12. Synchronous scanning luminescence: methods to detect pesticides and explosives

    NASA Astrophysics Data System (ADS)

    Hyfantis, George J., Jr.; Teglas, Matthew S.; Finnegan, Timothy P.; Mulligan, Patrick J.; Watts, Wendi

    1999-12-01

    The Synchronous Scanning Luminoscope (SSL) is a field- portable, synchronous luminescence spectrofluorometer that was developed for on-site analysis of contaminated soil and ground water. The SSL is capable of quantitative analysis of pesticides and explosives using phosphorescence and fluorescence techniques with a high correlation to laboratory data as illustrated by these studies. These techniques allow for rapid field assessments for pesticides and explosives. The Luminoscope is capable of detecting pesticides and explosives to the parts per billion (ppb) range. This paper describes standard field methods for using the SSL and describes the results of field/laboratory testing of explosives and pesticides.

  13. High-performance laboratories and cleanrooms

    SciTech Connect

    Tschudi, William; Sartor, Dale; Mills, Evan; Xu, Tengfang

    2002-07-01

    The California Energy Commission sponsored this roadmap to guide energy efficiency research and deployment for high performance cleanrooms and laboratories. Industries and institutions utilizing these building types (termed high-tech buildings) have played an important part in the vitality of the California economy. This roadmap's key objective to present a multi-year agenda to prioritize and coordinate research efforts. It also addresses delivery mechanisms to get the research products into the market. Because of the importance to the California economy, it is appropriate and important for California to take the lead in assessing the energy efficiency research needs, opportunities, and priorities for this market. In addition to the importance to California's economy, energy demand for this market segment is large and growing (estimated at 9400 GWH for 1996, Mills et al. 1996). With their 24hr. continuous operation, high tech facilities are a major contributor to the peak electrical demand. Laboratories and cleanrooms constitute the high tech building market, and although each building type has its unique features, they are similar in that they are extremely energy intensive, involve special environmental considerations, have very high ventilation requirements, and are subject to regulations--primarily safety driven--that tend to have adverse energy implications. High-tech buildings have largely been overlooked in past energy efficiency research. Many industries and institutions utilize laboratories and cleanrooms. As illustrated, there are many industries operating cleanrooms in California. These include semiconductor manufacturing, semiconductor suppliers, pharmaceutical, biotechnology, disk drive manufacturing, flat panel displays, automotive, aerospace, food, hospitals, medical devices, universities, and federal research facilities.

  14. Identification of Explosives from Porous Materials: Applications Using Reverse Phase High Performance Liquid Chromatography and Gas Chromatography

    SciTech Connect

    C.J. Miller; G. Elias; N.C. Schmitt; C. Rae

    2010-06-01

    High performance liquid chromatography and gas chromatography techniques are well documented and widely used for the detection of trace explosives from organic solvents. These techniques were modified to specifically identify and quantify explosives extracted from various materials taken from people who had recently handled explosives. Documented techniques were modified to specifically detect and quantify RDX, TNT, and PETN from denim, colored flannel, vinyl, and canvas extracted in methanol using no sample cleanup prior to analysis. The methanol extracts were injected directly into several different column types and analyzed by HPLC-UV and/or GC-ECD. This paper describes general screening methods that were used to determine the presence of explosives in unknown samples and techniques that have been optimized for quantification of each explosive from the substrate extracts.

  15. Effect of slow energy releasing on divergent detonation of Insensitive High Explosives

    NASA Astrophysics Data System (ADS)

    Hu, Xiaomian; Pan, Hao; Huang, Yong; Wu, Zihui

    2014-03-01

    There exists a slow energy releasing (SER) process in the slow reaction zone located behind the detonation wave due to the carbon cluster in the detonation products of Insensitive High Explosives (IHEs), and the process will affect the divergent detonation wave's propagation and the driving process of the explosives. To study the potential effect, a new artificial burn model including the SER process based on the programmed burn model is proposed in the paper. Quasi-steady analysis of the new model indicates that the nonlinearity of the detonation speed as a function of front curvature owes to the significant change of the reaction rate and the reaction zone length at the sonic state. What's more, in simulating the detonation of IHE JB-9014, the new model including the slow reaction can predict a slower jump-off velocity, in good agreement with the result of the test.

  16. Transmission and Reflection Terahertz Spectroscopy of Insensitive Melt-Cast High-Explosive Materials

    NASA Astrophysics Data System (ADS)

    Palka, Norbert; Szala, Mateusz

    2016-10-01

    Currently, artillery shells and grenades that are introduced into the market are based on melt-castable insensitive high explosives (IHEs), which do not explode while they run a risk of impact, heat or shrapnel. Particles of explosives (such as hexogen, nitroguanidine and nitrotriazolone) are suspended in different proportions in a matrix of 2.4-dinitroanisole. In this paper, we investigated samples of commonly used IHEs: PAX-41, IMX-104 and IMX-101, whose internal structures were determined by a scanning electron microscope. Terahertz time domain spectroscopy was applied in both transmission and reflection configurations. At first, the complex refraction indices of four pure constituents creating IHEs were determined and became the basis of further calculations. Next, the experimentally determined transmission and reflection spectra of IHEs and pure constituents were compared with theoretical considerations. The influence of the grain size of constituent material and scattering on the reflection spectra was analysed, and good agreement between the experimental and theoretical data was achieved.

  17. Detonation wave structure studies in high explosives by means of proton radiography

    NASA Astrophysics Data System (ADS)

    Kolesnikov, Sergei; Dudin, Sergei; Mintsev, Victor; Utkin, Alexander; Demidov, Victor; Fertman, Alexander; Golubev, Alexander; Katz, Mark; Markov, Nikolai; Sharkov, Boris; Smirnov, Gennady; Turtikov, Vladimir

    2007-06-01

    Proton radiography is the unique experimental technique for obtaining direct information about important material characteristics of real solid objects under dynamic conditions. The aim of the present work is the application of this method to the investigation of evolution of density in shock and detonation waves in high explosives (HE). Obtained information will be very useful for the improvement of existing detonation models and equations of state of HE. For this purpose a proton radiography facility for dynamic experiments on the basis of TWAC-ITEP accelerator is being constructed. A special containment chamber for explosive experiments was built. Static experiments with imitators of detonating HE charges were performed; as a result the proton radiographic images of imitators with time resolution of up to 10 ns were obtained. Dynamic experiments on the registration of detonation wave structure in pressed TNT are underway.

  18. Micro- and nano- second time scale, high power electrical wire explosions in water.

    NASA Astrophysics Data System (ADS)

    Grinenko, Alon; Efimov, Sergey; Sayapin, Arkadii; Fedotov, Alexander; Gurovich, Viktor; Krasik, Yakov

    2006-10-01

    Experimental and magneto-hydro-dynamic simulation results of micro- and nanosecond time scale underwater electrical Al, Cu and W wires explosions are presented. A capacitor bank with stored energy up to 6 kJ (discharge current up to 80 kA with 2.5 μs quarter period) was used in microsecond time scale experiments and water forming line generator with current amplitude up to 100 kA and pulse duration of 100 ns were used in nanosecond time scale experiments. Extremely high energy deposition of up to 60 times the atomization enthalpy was registered in nanosecond time scale explosions. A discharge channel evolution and surface temperature were analyzed by streak shadow imaging and using fast photo-diode with a set of interference filters, respectively. Microsecond time scale electrical explosion of cylindrical wire array showed extremely high pressure of converging shock waves at the axis, up to 0.2 MBar. A 1D and 2D magneto-hydro-dynamic simulation demonstrated good agreement with such experimental parameters as discharge channel current, voltage, radius, and temperature.

  19. 3-D high-speed imaging of volcanic bomb trajectory in basaltic explosive eruptions

    USGS Publications Warehouse

    Gaudin, D.; Taddeucci, J; Houghton, B. F.; Orr, Tim R.; Andronico, D.; Del Bello, E.; Kueppers, U.; Ricci, T.; Scarlato, P.

    2016-01-01

    Imaging, in general, and high speed imaging in particular are important emerging tools for the study of explosive volcanic eruptions. However, traditional 2-D video observations cannot measure volcanic ejecta motion toward and away from the camera, strongly hindering our capability to fully determine crucial hazard-related parameters such as explosion directionality and pyroclasts' absolute velocity. In this paper, we use up to three synchronized high-speed cameras to reconstruct pyroclasts trajectories in three dimensions. Classical stereographic techniques are adapted to overcome the difficult observation conditions of active volcanic vents, including the large number of overlapping pyroclasts which may change shape in flight, variable lighting and clouding conditions, and lack of direct access to the target. In particular, we use a laser rangefinder to measure the geometry of the filming setup and manually track pyroclasts on the videos. This method reduces uncertainties to 10° in azimuth and dip angle of the pyroclasts, and down to 20% in the absolute velocity estimation. We demonstrate the potential of this approach by three examples: the development of an explosion at Stromboli, a bubble burst at Halema'uma'u lava lake, and an in-flight collision between two bombs at Stromboli.

  20. Individual contributions of friction and impact on non-shock initiation of high explosives

    NASA Astrophysics Data System (ADS)

    Peterson, Paul; Avilucea, Gabe; Bishop, Robert; Sanchez, John

    2007-06-01

    Throughout the years a variety of tests have been designed which provide insight into the sensitivity of high explosives (HE) to non-shock initiation. Various standard tests such as the LANL drop weight impact, LLNL drop hammer, drop tower and skid tests have been developed to measure energetic response of explosives subjected to a combination of friction and oblique impact. In addition, the BAM test (for HE powders on roughened ceramic) and ABL friction test (powders or solids on roughened metal) have been developed for testing HE under frictional loading. In an effort to understand first principles of non-shock initiation, we have designed a series of tests to try to isolate friction and impact during the insult of HE. An initial series of tests have been completed with PETN, HMX, and as-pressed pellets of PBX 9501 (95 wt. percent HMX, 5 wt. percent inert binder), PBX 9502 (95 wt. percent TATB, wt. percent inert binder), Cyclotol (75 wt. percent RDX/25, wt. percent TNT), and Comp B3 (60 wt. percent RDX, 40 wt. percent TNT). The results suggest that some types of high explosives are relatively insensitive to pure impact and pure friction but relatively sensitive to insults involving a combination of impact and friction.

  1. Individual Contributions of Friction and Impact on Non-Shock Initiation of High Explosives

    NASA Astrophysics Data System (ADS)

    Peterson, P. D.; Avilucea, G. R.; Bishop, R. L.; Sanchez, J. A.

    2007-12-01

    Throughout the years a variety of tests have been designed which provide insight into the sensitivity of high explosives (HE) to non-shock initiation. Various standard tests such as the LANL drop weight impact, LLNL drop hammer, drop tower and skid tests have been developed to measure energetic response of explosives subjected to a combination of friction and oblique impact. In addition, the BAM test (for HE powders on roughened ceramic) and ABL friction test (powders or solids on roughened metal) have been developed for testing HE under frictional loading. In an effort to understand first principles of non-shock initiation, we have designed a series of tests to try to isolate friction and impact during the insult of HE. An initial series of tests have been completed with PETN, HMX, and as-pressed pellets of PBX 9501 (95 wt% HMX, wt% inert binder), PBX 9502 (95 wt% TATB, 5 wt% inert binder), Cyclotol (75 wt% RDX/25, wt% TNT), and Comp B3 (60 wt% RDX, 40 wt% TNT). The results suggest that some types of high explosives are relatively insensitive to pure impact and pure friction but relatively sensitive to insults involving a combination of impact and friction.

  2. Hydrodynamic Modeling of Air Blast Propagation from the Humble Redwood Chemical High Explosive Detonations Using GEODYN

    SciTech Connect

    Chipman, V D

    2011-09-20

    Two-dimensional axisymmetric hydrodynamic models were developed using GEODYN to simulate the propagation of air blasts resulting from a series of high explosive detonations conducted at Kirtland Air Force Base in August and September of 2007. Dubbed Humble Redwood I (HR-1), these near-surface chemical high explosive detonations consisted of seven shots of varying height or depth of burst. Each shot was simulated numerically using GEODYN. An adaptive mesh refinement scheme based on air pressure gradients was employed such that the mesh refinement tracked the advancing shock front where sharp discontinuities existed in the state variables, but allowed the mesh to sufficiently relax behind the shock front for runtime efficiency. Comparisons of overpressure, sound speed, and positive phase impulse from the GEODYN simulations were made to the recorded data taken from each HR-1 shot. Where the detonations occurred above ground or were shallowly buried (no deeper than 1 m), the GEODYN model was able to simulate the sound speeds, peak overpressures, and positive phase impulses to within approximately 1%, 23%, and 6%, respectively, of the actual recorded data, supporting the use of numerical simulation of the air blast as a forensic tool in determining the yield of an otherwise unknown explosion.

  3. VISAR Validation Test Series at the Light Initiated High Explosive (LIHE) facility.

    SciTech Connect

    Covert, Timothy Todd

    2007-02-01

    A velocity interferometer system for any reflector (VISAR) was recently deployed at the light initiated high explosive facility (LIHE) to measure the velocity of an explosively accelerated flyer plate. The velocity data from the flyer plate experiments, using the vendor's fringe constant of 100m/s/fringe, were consistently lower than model predictions. The goal of the VISAR validation test series was to confirm the VISAR system fringe constant. A low velocity gas gun was utilized to impact and accelerate a target at the LIHE facility. VISAR velocity data from the accelerated target was compared against an independent velocity measurement. The data from this test series did in fact reveal the fringe constant was significantly higher than the vendor's specification. The correct fringe constant for the LIHE VISAR system has been determined to be 123 m/s/fringe. The Light Initiated High Explosive (LIHE) facility recently completed a Phase I test series to develop an explosively accelerated flyer plate (X-Flyer). The X-Flyer impulse technique consists of first spraying a thin layer of silver acetylide silver nitrate explosive onto a thin flyer plate. The explosive is then initiated using an intense flash of light. The explosive detonation accelerates the flyer across a small air gap towards the test item. The impact of the flyer with the test item creates a shock pulse and an impulsive load in the test unit. The goal of Phase I of the X-Flyer development series was to validate the technique theory and design process. One of the key parameters that control the shock pulse and impulsive load is the velocity of the flyer at impact. To measure this key parameter, a velocity interferometer system for any reflector (VISAR) was deployed at the LIHE facility. The VISAR system was assembled by Sandia personnel from the Explosive Projects and Diagnostics department. The VISAR was a three leg, push-pull system using a fixed delay cavity. The primary optical components consisted of

  4. Characterisation and Modification of Thermally Stable High Explosives for Laser Flyer Applications

    NASA Astrophysics Data System (ADS)

    Parker, A.; Claridge, R. P.; Proud, W. G.; Johnson, N. A.

    2007-12-01

    Laser initiation offers improved weapon survivability, versatility and greater Insensitive Munitions (IM) compliance. Detonators based on laser-driven flyers are less vulnerable to electrical initiation and can be based on insensitive secondary explosives. Additionally, this technology will offer advantages in terms of improved flexibility and reliability. Hexanitrostilbene (HNS) and nonanitro-m-terphenyl (NONA) were selected for investigation at QinetiQ as their increased thermal stability over conventional explosives makes them ideal candidates for use in insensitive munition compliant applications. The response of these materials to short duration high-amplitude shock impulses provided by exploding foil initiators (EFI), the electrical equivalent of a laser-driven flyer system, was investigated. Preparation techniques including sonication and the incorporation of additives were used to sensitize the materials to flyer impact, yet maintain their insensitivity to external hazards. Sonication significantly reduced the particle size of both HNS and NONA. The reduced-size explosives exhibited increased sensitivity to EFI impact than the starting materials.

  5. Characterisation and modification of thermally stable high explosives for laser flyer applications

    SciTech Connect

    Parker, A.; Claridge, R. P.; Johnson, N. A.; Proud, W. G.

    2007-12-12

    Laser initiation offers improved weapon survivability, versatility and greater Insensitive Munitions (IM) compliance. Detonators based on laser-driven flyers are less vulnerable to electrical initiation and can be based on insensitive secondary explosives. Additionally, this technology will offer advantages in terms of improved flexibility and reliability. Hexanitrostilbene (HNS) and nonanitro-m-terphenyl (NONA) were selected for investigation at QinetiQ as their increased thermal stability over conventional explosives makes them ideal candidates for use in insensitive munition compliant applications. The response of these materials to short duration high-amplitude shock impulses provided by exploding foil initiators (EFI), the electrical equivalent of a laser-driven flyer system, was investigated. Preparation techniques including sonication and the incorporation of additives were used to sensitize the materials to flyer impact, yet maintain their insensitivity to external hazards. Sonication significantly reduced the particle size of both HNS and NONA. The reduced-size explosives exhibited increased sensitivity to EFI impact than the starting materials.

  6. Mid-IR DIAL for high-resolution mapping of explosive precursors

    NASA Astrophysics Data System (ADS)

    Mitev, V.; Babichenko, S.; Bennes, J.; Borelli, R.; Dolfi-Bouteyre, A.; Fiorani, L.; Hespel, L.; Huet, T.; Palucci, A.; Pistilli, M.; Puiu, A.; Rebane, O.; Sobolev, I.

    2013-10-01

    A DIAL instrument on a moving platform is seen as a valuable remote sensing component in a sensor network for area monitoring, targeting sites involved in unauthorised explosive manufacturing. Such instrument will perform the area mapping of the vapour concentration of key substances, known to be used as precursors in explosive fabrication, such as acetone and nitromethane. The IR spectra of acetone and nitromethane vapours have been defined from available spectroscopy databases and from laboratory measurements as showing optimal spectral band for the DIAL operation in the spectral range of 3.0 μm - 3.5 μm. The DIAL operation has been numerically simulated, with inputs based on the HITRAN database, the U.S. Standard Atmosphere and aerosol simulation software package OPAC. A combination of OPO and OPA has been chosen as a transmitter, where the idler wavelength is used for probing, with wavelength tuning in sequence. A scanner mounted on top of the coaxially aligned laser and receiver, is capable of covering almost 360 degrees horizontally and +/-30 degrees vertically. The detection is performed by a photovoltaic photodiode with 4-stage cooling, with a signal digitalisation having 14 bit amplitude resolution and 125 Ms/s sampling rate. Here we present the development and the first test of the DIAL instrument.

  7. Nanoengineered explosives

    DOEpatents

    Makowiecki, D.M.

    1996-04-09

    A complex modulated structure is described for reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures. 2 figs.

  8. Nanoengineered explosives

    DOEpatents

    Makowiecki, Daniel M.

    1996-01-01

    A complex modulated structure of reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures.

  9. A SURVEY OF HIGH EXPLOSIVE-INDUCED DAMAGE AND SPALL IN SELECTED METALS USING PROTON RADIOGRAPHY.

    SciTech Connect

    Holtkamp, D. B.; Clark, D. A.; Ferm, E. N.; Gallegos, R. A.; Hammon, D.; Hemsing, W. F.; Hogan, G. E.; Holmes, V. H.; King, N.. S.P; liljestrand, R.; Lopez, R. P.; Merrill, F. E.; Morris, C. L.; Morley, K. B.; Murray, M. M.; Pazuchanics, P. D.; Prestridge, K. P.; Quintana, J. P.; Saunders, A.; Schafer, T.; Shinas, M. A.

    2003-07-01

    Multiple spall and damage layers can be created in metal when the free surface reflects a Taylor wave generated by high explosives. These phenomena have been explored in different thicknesses of several metals (tantalum, copper, 6061 T6-aluminum, and tin) using high-energy proton radiography. Multiple images (up to 21) can be produced of the dynamic evolution of damaged material on the microsecond time scale with a <50 ns “shutter” time. Movies and multiframe still images of areal and (Abel inverted) volume densities are presented. An example of material that is likely melted on release (tin) is also presented..

  10. Perchlorate contamination from the detonation of insensitive high-explosive rounds.

    PubMed

    Walsh, Michael R; Walsh, Marianne E; Ramsey, Charles A; Brochu, Sylvie; Thiboutot, Sonia; Ampleman, Guy

    2013-11-15

    The insensitive high-explosive PAX-21 was the first of its kind fielded in an artillery munition by the United States military. This formulation contains three main components: RDX, dinitroanisole, and ammonium perchlorate (AP). In March 2012, detonation tests were conducted on PAX-21 60mm mortar rounds to determine the energetic residues resulting from high-order and blow-in-place (BIP) detonations. Post-detonation residues were sampled and analyzed for the three main PAX-21 components. Concentrations of RDX and dinitroanisole in the samples were quite low, less than 0.1% of the munitions' original organic explosive filler mass, indicating high order or near high order detonations. However, disproportionately high concentrations of AP occurred in all residues. The residues averaged 15% of the original AP following high-order detonations and 38% of the original AP mass following the BIP operations. There was no correlation between AP residues and the RDX and dinitroanisole. Perchlorate readily leached from the detonation residues, with over 99% contained in the aqueous portion of the samples. Use of these rounds will result in billions of liters of water contaminated above drinking water perchlorate limits. As a result of this research, PAX-21 mortar rounds are currently restricted from use on US training ranges.

  11. Long-range seismic recording of the MISTY PICTURE high-explosive test, White Sands Missile Range, New Mexico. Environmental research papers, February 1987-February 1988

    SciTech Connect

    Cipar, J.

    1988-02-04

    The Solid Earth Geophysics Branch of the Air Force Geophysics Laboratory recorded the MISTY PICTURE high-explosive test at nine sites in the Tularosa Basin of southern New Mexico. Each site consisted of a three-component seismometer set and a digital-event recorder. The stations were due south of the explosion between 95 and 127 km. Analysis of P-wave travel times indicates that the crust is 30-32 km thick beneath the Tularosa Basin, a side graben of the Rio Grande Rift. S-wave travel times are consistent with earlier surface-wave results. Polarization analysis indicates complex scattered and converted energy between the P- and S-wave groups.

  12. Extrusion cast explosive

    DOEpatents

    Scribner, K.J.

    1985-11-26

    Disclosed is an improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants. 1 fig.

  13. Extrusion cast explosive

    DOEpatents

    Scribner, K.J.

    1985-01-29

    Improved, multiphase, high performance, high energy, extrusion cast explosive compositions, comprising, a crystalline explosive material; an energetic liquid plasticizer; a urethane prepolymer, comprising a blend of polyvinyl formal, and polycaprolactone; a polyfunctional isocyanate; and a catalyst are disclosed. These new explosive compositions exhibit higher explosive content, a smooth detonation front, excellent stability over long periods of storage, and lower sensitivity to mechanical stimulants. 1 fig.

  14. Effects of Various Blowout Panel Configurations on the Structural Response of Los Alamos National Laboratory Building 16-340 to Internal Explosions

    SciTech Connect

    Wilke, Jason P.

    2005-09-01

    The risk of accidental detonation is present whenever any type of high explosives processing activity is performed. These activities are typically carried out indoors to protect processing equipment from the weather and to hide possibly secret processes from view. Often, highly strengthened reinforced concrete buildings are employed to house these activities. These buildings may incorporate several design features, including the use of lightweight frangible blowout panels, to help mitigate blast effects. These panels are used to construct walls that are durable enough to withstand the weather, but are of minimal weight to provide overpressure relief by quickly moving outwards and creating a vent area during an accidental explosion. In this study the behavior of blowout panels under various blast loading conditions was examined. External loadings from explosions occurring in nearby rooms were of primary interest. Several reinforcement systems were designed to help blowout panels resist failure from external blast loads while still allowing them to function as vents when subjected to internal explosions. The reinforcements were studied using two analytical techniques, yield-line analysis and modal analysis, and the hydrocode AUTODYN. A blowout panel reinforcement design was created that could prevent panels from being blown inward by external explosions. This design was found to increase the internal loading of the building by 20%, as compared with nonreinforced panels. Nonreinforced panels were found to increase the structural loads by 80% when compared to an open wall at the panel location.

  15. Contribution of Neutron Beta Decay to Radiation Belt Pumping from High Altitude Nuclear Explosion

    SciTech Connect

    Marrs, R

    2002-11-13

    In 1962, several satellites were lost following high altitude nuclear tests by the United States and the Soviet Union. These satellite failures were caused by energetic electrons injected into the earth's radiation belts from the beta decay of bomb produced fission fragments and neutrons. It has been 40 years since the last high altitude nuclear test; there are now many more satellites in orbit, and it is important to understand their vulnerability to radiation belt pumping from nuclear explosions at high altitude or in space. This report presents the results of a calculation of the contribution of neutron beta decay to artificial belt pumping. For most high altitude nuclear explosions, neutrons are expected to make a smaller contribution than fission products to the total trapped electron inventory, and their contribution is usually neglected. However, the neutron contribution may dominate in cases where the fission product contribution is suppressed due to the altitude or geomagnetic latitude of the nuclear explosion, and for regions of the radiation belts with field lines far from the detonation point. In any case, an accurate model of belt pumping from high altitude nuclear explosions, and a self-consistent explanation of the 1962 data, require inclusion of the neutron contribution. One recent analysis of satellite measurements of electron flux from the 1962 tests found that a better fit to the data is obtained if the neutron contribution to the trapped electron inventory was larger than that of the fission products [l]. Belt pumping from high altitude nuclear explosions is a complicated process. Fission fragments are dispersed as part of the ionized bomb debris, which is constrained and guided by the earth's magnetic field. Those fission products that beta decay before being lost to the earth's atmosphere can contribute trapped energetic electrons to the earth's radiation belts. There has been a large effort to develop computer models for the contribution of

  16. SUPERFUND TREATABILITY CLEARINGHOUSE: COMPOSITING EXPLOSIVES/ORGANICS CONTAMINATED SOILS

    EPA Science Inventory

    Laboratory scale and pilot scale studies were conducted to evaluate composting to treat sediments and soils containing explosive and organic compounds. Sediment and soil from lagoons at Army ammunition plants, located in Louisiana, Wisconsin and Pennsylvania contained high...

  17. Understanding highly explosive basaltic eruptions: Evidence from olivine-hosted melt inclusions from Sunset Crater, AZ

    NASA Astrophysics Data System (ADS)

    Allison, C. M.; Roggensack, K.; Clarke, A. B.; Alfano, F.

    2013-12-01

    Basaltic scoria cone volcanoes are the most abundant volcanic landform on Earth and occur in all tectonic settings. Basaltic magmas have lower viscosities, higher temperatures, and lower volatile contents than silicic magmas, and therefore generally have a lower potential for explosive activity. However, basaltic eruptions display great variability, from mild lava flows to more energetic explosions with large plumes. The mechanism controlling highly explosive basaltic eruptions, such as the ca. 1085 AD eruption of Sunset Crater, is poorly understood. Processes or conditions such as high volatile content in the source magma, injection of a compositionally distinct magma at depth, interaction with shallow magma reservoirs, or rapid crystallization and/or bubble nucleation in the shallow subsurface could increase explosivity of basaltic magmas. One method to test these hypotheses is melt inclusion analysis in order to constrain initial melt composition, volatile content and minimum storage depth. The San Francisco Volcanic Field (SFVF) in northern Arizona, active from 6 Ma-present, consists of over 600 volcanoes - mainly alkali basalt scoria cones along with five silicic centers. The eruption of Sunset Crater in the SFVF during the Holocene was an anomalously large basaltic explosive eruption, consisting of >8 explosive phases and 3 lava flows. Typical scoria cone-forming eruptions produce <0.1 km3 DRE of material, while the Sunset Crater tephra deposit is on the order of ~0.3 km3 DRE, with each phase characterized by volumes of 0.02-0.08 km3 DRE. The phases vary in size and style; the beginning stages of explosive activity (phases 1-2) were considerably smaller than phases 3-5, classified as subplinian. Because of the young age and desert setting of the volcano, the eruptive material is fresh and the deposit is well preserved. The bulk composition is an alkali basalt with Mg# 74. We studied 40 primary melt inclusions (MIs) hosted in 36 olivine crystals 0.5-2 mm in

  18. Laser photoacoustic spectroscopy helps fight terrorism: High sensitivity detection of chemical Warfare Agent and explosives

    NASA Astrophysics Data System (ADS)

    Patel, C. K. N.

    2008-01-01

    Tunable laser photoacoustic spectroscopy is maturing rapidly in its applications to real world problems. One of the burning problems of the current turbulent times is the threat of terrorist acts against civilian population. This threat appears in two distinct forms. The first is the potential release of chemical warfare agents (CWA), such as the nerve agents, in a crowded environment. An example of this is the release of Sarin by Aum Shinrikyo sect in a crowded Tokyo subway in 1995. An example of the second terrorist threat is the ever-present possible suicide bomber in crowded environment such as airports, markets and large buildings. Minimizing the impact of both of these threats requires early detection of the presence of the CWAs and explosives. Photoacoustic spectroscopy is an exquisitely sensitive technique for the detection of trace gaseous species, a property that Pranalytica has extensively exploited in its CO2 laser based commercial instrumentation for the sub-ppb level detection of a number of industrially important gases including ammonia, ethylene, acrolein, sulfur hexafluoride, phosphine, arsine, boron trichloride and boron trifluoride. In this presentation, I will focus, however, on our recent use of broadly tunable single frequency high power room temperature quantum cascade lasers (QCL) for the detection of the CWAs and explosives. Using external grating cavity geometry, we have developed room temperature QCLs that produce continuously tunable single frequency CW power output in excess of 300 mW at wavelengths covering 5 μm to 12 μm. I will present data that show a CWA detection capability at ppb levels with false alarm rates below 1:108. I will also show the capability of detecting a variety of explosives at a ppb level, again with very low false alarm rates. Among the explosives, we have demonstrated the capability of detecting homemade explosives such as triacetone triperoxide and its liquid precursor, acetone which is a common household

  19. Explosive laser

    DOEpatents

    Robinson, C.P.; Jensen, R.J.; Davis, W.C.; Sullivan, J.A.

    1975-09-01

    This patent relates to a laser system wherein reaction products from the detonation of a condensed explosive expand to form a gaseous medium with low translational temperature but high vibration population. Thermal pumping of the upper laser level and de-excitation of the lower laser level occur during the expansion, resulting in a population inversion. The expansion may be free or through a nozzle as in a gas-dynamic configuration. In one preferred embodiment, the explosive is such that its reaction products are CO$sub 2$ and other species that are beneficial or at least benign to CO$sub 2$ lasing. (auth)

  20. A Review of U.S. High Explosive Pulsed Power Systems

    SciTech Connect

    Goforth, J.H.

    1998-10-18

    High explosive pulsed power (HEPP) is a specialized subset among pulsed power endeavors which takes advantage of the very high energy density available in both magnetic fields and high explosives (HE). To introduce basic concepts, the author divides HEPP components into generators (magnetic field (B) or current (I)) and switches. Magnetic field and current generators start with magnetic field trapped in a conducting volume. Magnetic flux can be expressed as either LI or BA, where L and A (inductance and cross sectional area) are both geometry dependent circuit properties. In a purely inductive circuit, flux is conserved, so L{sub 1}I{sub 1}=L{sub 2}I{sub 2} or B{sub 1}A{sub 1}=B{sub 2}A{sub 2}. In the technique, HE is used to propel circuit elements that perform work against the trapped magnetic field as L or A is reduced, yielding increased I or B. Throughout this paper, the author uses the term flux compression generator (FCG) for these devices, although the reader will find a variety of acronyms in the literature. A good primer on FCG's is by Fowler et al. HE is also used to provide opening and closing switches for HEPP circuits. Closing switches do not require great sophistication, and they don't discuss them here. Opening switches typically use the energy of HE to rapidly reduce the current carrying cross section of a particular circuit element, and often require sophisticated detonation systems to match the contour of that element (e. g. cylindrical). This may either cause a direct increase in resistance or create the circumstance in which the remainder of the material fuses due to ohmic effects. Many good papers on explosive-driven opening switches can be found in previous Megagauss conference proceedings, and these are also a good source for information regarding HEPP endeavors outside the US, which is beyond the scope of this paper.

  1. High explosives vapor detection by atmospheric sampling glow discharge ionization/tandem mass spectrometry

    SciTech Connect

    McLuckey, S.A.; Goeringer, D.E.; Asano, K.G.

    1996-02-01

    The combination of atmospheric sampling glow discharge ionization with tandem mass spectrometry for the detection of traces of high explosives is described. Particular emphasis is placed on use of the quadrupole ion trap as the type of tandem mass spectrometer. Atmospheric sampling glow discharge provides a simple, rugged, and efficient means for anion formation while the quadrupole ion trap provides for efficient tandem mass spectrometry. Mass selective ion accumulation and non-specific ion activation methods can be used to overcome deleterious effects arising from ion/ion interactions. Such interactions constitute the major potential technical barrier to the use of the ion trap for real-time monitoring of targeted compounds in uncontrolled and highly variable matrices. Tailored waveforms can be used to effect both mass selective ion accumulation and ion activation. Concatenated tailored waveforms allow for both functions in a single experiment thereby providing the capability for monitoring several targeted species simultaneously. The combination of atmospheric sampling glow discharge ionization with a state-of-the-art analytical quadrupole ion trap is a highly sensitive and specific detector for traces of high explosives. The combination is also small and inexpensive relative to virtually any other form of tandem mass spectrometry. The science and technology underlying the glow discharge/ion trap combination is sufficiently mature to form the basis for an engineering effort to make the detector portable. 85 refs.

  2. Explosive vaporization of a large transparent droplet irradiated by a high intensity laser.

    PubMed

    Zhang, J Z; Lam, J K; Wood, C F; Chu, B T; Chang, R K

    1987-11-15

    Shadowgraph studies of the explosive vaporization of a transparent water droplet after irradiation by a high intensity beam show that dielectric breakdown occurs within the droplet shadow face and generates a dense plasma, which absorbs the laser pulse. The convective forces expel the vapor from the droplet shadow face. We have deduced (1) the vapor propagation velocities, (2) the recoil velocity of the remaining droplet, and (3) the deformation rate of the illuminated face. Droplets are noted to eject fingerlike material from the surface facing the single laser-vaporized droplet when the asymmetrical vapor intercepts the neighboring droplets.

  3. Highly sensitive detection of explosive triacetone triperoxide by an In2O3 sensor.

    PubMed

    Zhang, Wen-Hui; Zhang, Wei-De; Chen, Lu-Ya

    2010-08-01

    Triacetone triperoxide (TATP) is one of the most sensitive known explosives and can be easily synthesized using the commonly available chemicals acetone and hydrogen peroxide, but is difficult to be detected. In this study, In(2)O(3) nanoparticles were synthesized by a glucose-assisted solvothermal method at 120 degrees C for 18 h. The gas sensor based on In(2)O(3) nanoparticles exhibits a high response, fast response and recovery, a wide detecting range of 0.50-500 mg, good stability and excellent stability to TATP. PMID:20634566

  4. Highly sensitive detection of explosive triacetone triperoxide by an In2O3 sensor

    NASA Astrophysics Data System (ADS)

    Zhang, Wen-Hui; Zhang, Wei-De; Chen, Lu-Ya

    2010-08-01

    Triacetone triperoxide (TATP) is one of the most sensitive known explosives and can be easily synthesized using the commonly available chemicals acetone and hydrogen peroxide, but is difficult to be detected. In this study, In2O3 nanoparticles were synthesized by a glucose-assisted solvothermal method at 120 °C for 18 h. The gas sensor based on In2O3 nanoparticles exhibits a high response, fast response and recovery, a wide detecting range of 0.50-500 mg, good stability and excellent stability to TATP.

  5. Explosive complexes

    DOEpatents

    Huynh, My Hang V.

    2011-08-16

    Lead-free primary explosives of the formula [M.sup.II(A).sub.R(B.sup.X).sub.S](C.sup.Y).sub.T, where A is 1,5-diaminotetrazole, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  6. Explosive complexes

    DOEpatents

    Huynh, My Hang V.

    2009-09-22

    Lead-free primary explosives of the formula [M.sup.II(A).sub.R(B.sup.X).sub.S](C.sup.Y).sub.T, where A is 1,5-diaminotetrazole, and syntheses thereof are described. Substantially stoichiometric equivalents of the reactants lead to high yields of pure compositions thereby avoiding dangerous purification steps.

  7. Non-detonable explosive simulators

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1994-11-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules. 5 figs.

  8. Non-detonable explosive simulators

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1994-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules.

  9. The Plumbing System of a Highly Explosive Basaltic Volcano: Sunset Crater, AZ

    NASA Astrophysics Data System (ADS)

    Allison, C. M.; Roggensack, K.; Clarke, A. B.

    2015-12-01

    We seek to better understand highly explosive basaltic eruptions with specific focus on magmatic volatile solubility in alkali basalts and the magma plumbing system. Sunset Crater, an alkali basalt (~3.7 wt.% alkalis) scoria cone volcano, erupted explosively in 1085 AD. We analyzed 125 primary melt inclusions (MIs) from Sunset Crater tephra deposited by 2 subplinian phases and 1 Strombolian explosion to compare magma volatiles and storage conditions. We picked rapidly quenched free olivine crystals and selected large volume MIs (50-180 μm) located toward crystal cores. MIs are faceted and exhibit little major element composition variability with minor post entrapment crystallization (2-10%). MIs are relatively dry but CO2-rich. Water content varies from 0.4 wt.% to 1.5 wt.% while carbon dioxide abundance ranges between 1,150 ppm and 3,250 ppm. Most MIs contain >1 wt.% H2O and >2,150 ppm CO2. All observed MIs contain a vapor bubble, so we are evaluating MI vapor bubbles with Raman spectroscopy and re-homogenization experiments to determine the full volatile budget. Because knowledge of volatile solubility is critical to accurately interpret results from MI analyses, we measured H2O-CO2 solubility in the Sunset Crater bulk composition. Fluid-saturated experiments at 4 and 6 kbar indicate shallower entrapment pressures for these MIs than values calculated for this composition using existing models. Assuming fluid saturation, MIs record depths from 6 km to 14 km, including groupings suggesting two pauses for longer-term storage at ~6 km and ~10.5 km. We do not observe any significant differences in MIs from phases exhibiting different eruptive styles, suggesting that while a high CO2 content may drive rapid magma ascent and be partly responsible for highly explosive eruptions, shallower processes may govern the final eruptive character. To track shallow processes during magma ascent from depth of MI-entrapment up to the surface, we are examining MI re-entrants.

  10. Deflagration of HMX-Based Explosives at High Temperatures and Pressures

    SciTech Connect

    Maienschein, J L; Wardell, J F; DeHaven, M R; Black, C K

    2004-05-12

    We measure the deflagration behavior of energetic materials at extreme conditions (up to 520K and 1 GPa) in the LLNL High Pressure Strand Burner, thereby obtaining reaction rate data for prediction of violence of thermal explosions. The apparatus provides both temporal pressure history and flame time-of-arrival information during deflagration, allowing direct calculation of deflagration rate as a function of pressure. Samples may be heated before testing. Here we report the deflagration behavior of several HMX-based explosives at pressures of 10-600 MPa and temperatures of 300-460 K. We find that formulation details are very important to overall deflagration behavior. Formulations with high binder content (>15 wt%) deflagrate smoothly over the entire pressure range regardless of particle size, with a larger particle size distribution leading to a slower reaction. The deflagration follows a power law function with the pressure exponent being unity. Formulations with lower binder content ({le} 10% or less by weight) show physical deconsolidation at pressures over 100-200 MPA, with transition to a rapid erratic deflagration 10-100 times faster. High temperatures have a relatively minor effect on the deflagration rate until the HMX {beta} {yields} {delta} phase transition occurs, after which the deflagration rate increases by more than a factor of 10.

  11. Deflagration Behavior of HMX-Based Explosives at High Temperatures and Pressures

    SciTech Connect

    Maienschein, J L; Wardell, J F

    2003-11-20

    We report the deflagration behavior of several HMX-based explosives at pressure from 10-600 MPa and temperatures from 20-180 C. We have made laminar burn rate measurements with the LLNL High Pressure Strand Burner, in which burn wires are used to record the time-of-arrival of the burn front in the cylindrical sample as a function of pressure. The explosive samples are 6.4 mm in diameter and 63 mm long, with ten burn wires embedded at different positions in the sample. Burning on the cylindrical surface is inhibited with an epoxy layer. With this direct measurement we do not have to account for product gas equation of state or heat losses in the system, and the burn wires allow detection of irregular burning. We find that formulation details are very important to overall deflagration behavior - the presence of 10% or less by weight of binder leads to physical deconsolidation and rapid deflagration at high pressures, and a larger particle size distribution leads to slower deflagration. High temperatures have a relatively minor effect on the deflagration rate until the beta-to-delta phase transition temperature is reached, beyond which the deflagration rate increases approximately 40-fold.

  12. Modeling the Structural Response from a Propagating High Explosive Using Smooth Particle Hydrodynamics

    SciTech Connect

    Margraf, J

    2012-06-12

    This report primarily concerns the use of two massively parallel finite element codes originally written and maintained at Lawrence Livermore National Laboratory. ALE3D is an explicit hydrodynamics code commonly employed to simulate wave propagation from high energy scenarios and the resulting interaction with nearby structures. This coupled response ensures that a structure is accurately applied with a blast loading varying both in space and time. Figure 1 illustrates the radial outward propagation of a pressure wave due to a center detonated spherical explosive originating from the lower left. The radial symmetry seen in this scenario is lost when instead a cylindrocal charge is detonated. Figure 2 indicates that a stronger, faster traveling pressure wave occurs in the direction of the normal axis to the cylinder. The ALE3D name is derived because of the use of arbitrary-Lagrange-Eulerian elements in which the mesh is allowed to advect; a process through which the mesh is modified to alleviate tanlging and general mesh distortion often cuased by high energy scenarios. The counterpart to an advecting element is a Lagrange element, whose mesh moves with the material. Ideally all structural components are kept Lagrange as long as possible to preserve accuracy of material variables and minimize advection related errors. Advection leads to mixed zoning, so using structural Lagrange elements also improves the visualization when post processing the results. A simplified representation of the advection process is shown in Figure 3. First the mesh is distorted due to material motion during the Lagrange step. The mesh is then shifted to an idealized and less distorted state to prevent irregular zones caused by the Lagrange motion. Lastly, the state variables are remapped to the elements of the newly constructed mesh. Note that Figure 3 represents a purely Eulerian mesh relaxation because the mesh is relocated back to the pre-Lagrange position. This is the case when the

  13. The Use of the Propellant Specific Impulse for the Prediction of the Prompt and Terminal Gurney Velocity of High Explosives

    NASA Astrophysics Data System (ADS)

    Frem, Dany

    2016-10-01

    Simple relationships are presented for the calculation of both prompt and terminal Gurney velocity of chemical high explosives. By considering that a given explosive behaves like a propellant, its specific impulse ? was calculated using Mader's ISPBKW code; it was found that the density impulse (?where ? is the explosive density and ? is an empirically optimized variable) performance factor correlates well with the terminal Gurney velocity of both ideal and nonideal explosives. Furthermore, the cylinder wall energy can be computed from (?from which the prompt Gurney velocity can be obtained through the application of the Gurney's cylinder equation. It was concluded that (? is a powerful factor for the prediction of the Gurney velocities, especially for nonideal compositions.

  14. The application of single particle aerosol mass spectrometry for the detection and identification of high explosives and chemical warfare agents

    SciTech Connect

    Martin, Audrey Noreen

    2006-01-01

    Single Particle Aerosol Mass Spectrometry (SPAMS) was evaluated as a real-time detection technique for single particles of high explosives. Dual-polarity time-of-flight mass spectra were obtained for samples of 2,4,6-trinitrotoluene (TNT), 1,3,5-trinitro-1,3,5-triazinane (RDX), and pentaerythritol tetranitrate (PETN); peaks indicative of each compound were identified. Composite explosives, Comp B, Semtex 1A, and Semtex 1H were also analyzed, and peaks due to the explosive components of each sample were present in each spectrum. Mass spectral variability with laser fluence is discussed. The ability of the SPAMS system to identify explosive components in a single complex explosive particle (~1 pg) without the need for consumables is demonstrated. SPAMS was also applied to the detection of Chemical Warfare Agent (CWA) simulants in the liquid and vapor phases. Liquid simulants for sarin, cyclosarin, tabun, and VX were analyzed; peaks indicative of each simulant were identified. Vapor phase CWA simulants were adsorbed onto alumina, silica, Zeolite, activated carbon, and metal powders which were directly analyzed using SPAMS. The use of metal powders as adsorbent materials was especially useful in the analysis of triethyl phosphate (TEP), a VX stimulant, which was undetectable using SPAMS in the liquid phase. The capability of SPAMS to detect high explosives and CWA simulants using one set of operational conditions is established.

  15. In-situ Raman spectroscopy and high-speed photography of a shocked triaminotrinitrobenzene based explosive

    SciTech Connect

    Saint-Amans, C.; Hébert, P. Doucet, M.; Resseguier, T. de

    2015-01-14

    We have developed a single-shot Raman spectroscopy experiment to study at the molecular level the initiation mechanisms that can lead to sustained detonation of a triaminotrinitrobenzene-based explosive. Shocks up to 30 GPa were generated using a two-stage laser-driven flyer plate generator. The samples were confined by an optical window and shock pressure was maintained for at least 30 ns. Photon Doppler Velocimetry measurements were performed at the explosive/window interface to determine the shock pressure profile. Raman spectra were recorded as a function of shock pressure and the shifts of the principal modes were compared to static high-pressure measurements performed in a diamond anvil cell. Our shock data indicate the role of temperature effects. Our Raman spectra also show a progressive extinction of the signal which disappears around 9 GPa. High-speed photography images reveal a simultaneous progressive darkening of the sample surface up to total opacity at 9 GPa. Reflectivity measurements under shock compression show that this opacity is due to a broadening of the absorption spectrum over the entire visible region.

  16. Ruminal bioremediation of the high energy melting explosive (HMX) by sheep microorganisms.

    PubMed

    Eaton, Hillary L; Murty, Lia D; Duringer, Jennifer M; Craig, A Morrie

    2014-01-01

    The ability of ruminal microorganisms to degrade octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (high melting explosive, HMX) as consortia from whole rumen fluid (WRF), and individually as 23 commercially available ruminal strains, was compared under anaerobic conditions. Compound degradation was monitored by high-performance liquid chromatography, followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) for delineation of the metabolic pathway. In WRF, 30 μM HMX was degraded to 5 μM HMX within 24 h. Metabolites consistent with m/z 149, 193 and 229 were present throughout the incubation period. We propose that peaks with an m/z of 149 and 193 are arrived at through reduction of HMX to nitroso or hydroxylamino intermediates, then direct enzymatic ring cleavage to produce these HMX derivatives. Possible structures of m/z 229 are still being investigated and require further LC-MS/MS analysis. None of the 23 ruminal strains tested were able to degrade HMX as a pure culture when grown in either a low carbon or low nitrogen basal medium over 120 h. We conclude that microorganisms from the rumen, while sometimes capable as individuals in the bioremediation of other explosives, excel as a community in the case of HMX breakdown.

  17. In-situ Raman spectroscopy and high-speed photography of a shocked triaminotrinitrobenzene based explosive

    NASA Astrophysics Data System (ADS)

    Saint-Amans, C.; Hébert, P.; Doucet, M.; de Resseguier, T.

    2015-01-01

    We have developed a single-shot Raman spectroscopy experiment to study at the molecular level the initiation mechanisms that can lead to sustained detonation of a triaminotrinitrobenzene-based explosive. Shocks up to 30 GPa were generated using a two-stage laser-driven flyer plate generator. The samples were confined by an optical window and shock pressure was maintained for at least 30 ns. Photon Doppler Velocimetry measurements were performed at the explosive/window interface to determine the shock pressure profile. Raman spectra were recorded as a function of shock pressure and the shifts of the principal modes were compared to static high-pressure measurements performed in a diamond anvil cell. Our shock data indicate the role of temperature effects. Our Raman spectra also show a progressive extinction of the signal which disappears around 9 GPa. High-speed photography images reveal a simultaneous progressive darkening of the sample surface up to total opacity at 9 GPa. Reflectivity measurements under shock compression show that this opacity is due to a broadening of the absorption spectrum over the entire visible region.

  18. Modern Foreign Languages in High School: The Language Laboratory.

    ERIC Educational Resources Information Center

    Hutchinson, Joseph C.

    The high school language laboratory is approached from the standpoint of (1) planning for the laboratory facilities, (2) the function of equipment in relation to student learning activities, and (3) operation of the laboratory facilities. Considered in the section on planning are laboratory rationale, place in the school program, methods and…

  19. Relativistic waves raised by explosions in space as sources of ultra-high-energy cosmic rays

    NASA Astrophysics Data System (ADS)

    Kichigin, G. N.

    2013-01-01

    The paper discusses the possibility of particle acceleration up to high energies in relativistic waves generated by various explosive processes in the interstellar medium. We propose to use the surfatron mechanism of acceleration (surfing) of charged particles trapped in the front of relativistic waves as a generator of high-energy cosmic rays (CRs). Conditions under which surfing in the waves under consideration can be made are studied thoroughly. Ultra-high-energy CRs (up to 1020 eV) are shown to be obtained due to the surfing in relativistic plane and spherical waves. Surfing is supposed to take place in nonlinear Langmuir waves excited by powerful electromagnetic radiation or relativistic beams of charged particles, as well as in strong shock waves generated by relativistic jets or spherical formations that expand fast (fireballs).

  20. Multiphysics Simulations of Hot-Spot Initiation in Shocked Insensitive High-Explosive

    NASA Astrophysics Data System (ADS)

    Najjar, Fady; Howard, W. M.; Fried, L. E.

    2010-11-01

    Solid plastic-bonded high-explosive materials consist of crystals with micron-sized pores embedded. Under mechanical or thermal insults, these voids increase the ease of shock initiation by generating high-temperature regions during their collapse that might lead to ignition. Understanding the mechanisms of hot-spot initiation has significant research interest due to safety, reliability and development of new insensitive munitions. Multi-dimensional high-resolution meso-scale simulations are performed using the multiphysics software, ALE3D, to understand the hot-spot initiation. The Cheetah code is coupled to ALE3D, creating multi-dimensional sparse tables for the HE properties. The reaction rates were obtained from MD Quantum computations. Our current predictions showcase several interesting features regarding hot spot dynamics including the formation of a "secondary" jet. We will discuss the results obtained with hydro-thermo-chemical processes leading to ignition growth for various pore sizes and different shock pressures.

  1. Direct hydrolysis of cellulose to glucose using ultra-high temperature and pressure steam explosion.

    PubMed

    Sasaki, Chizuru; Sumimoto, Keisuke; Asada, Chikako; Nakamura, Yoshitoshi

    2012-06-01

    Hydrolysis of two cellulosic materials, i.e. microcrystalline cellulose powder (MC) and cuprammonium rayon fiber (BEMCOT), to glucose was carried out by steam explosion treatment with ultra-high temperature and pressure steam aiming at an effective usage of unutilized cellulosic materials. 50 g of cellulosic materials were charged in a sealed reactor (2L) of the steam explosion apparatus kept at steam pressures of 50, 55, 60, and 62 atm for a steaming time of 1 min. The maximum yield of water soluble sugars, 52.8%, was obtained at a steam pressure of 62 atm and a steaming time of 1 min for MC. Furthermore, the maximum yield of water soluble sugars, 67.7%, was obtained at a steam pressure of 60 atm and a steaming time of 1 min for BEMCOT. This water soluble sugars contained 63.1% and 61.0% of glucose, respectively; they are corresponding to 33.3g and 41.0 g of glucose contained in 100g of dry steam-exploded cellulosic material.

  2. Safety in the Chemical Laboratory: Group Contribution Method for Predicting the Potential of a Chemical Composition to Cause an Explosion.

    ERIC Educational Resources Information Center

    Seaton, William H.

    1989-01-01

    Provided is an empirical method to train students to avoid physical disaster in their work experience. Discussed is a computer program, CHETAH, which can be used in advance of synthesis to classify the possible explosive nature of the products. Plosophoric and auxoplosive weights of many organic groups are listed. (MVL)

  3. Niche explosion.

    PubMed

    Normark, Benjamin B; Johnson, Norman A

    2011-05-01

    The following syndrome of features occurs in several groups of phytophagous insects: (1) wingless females, (2) dispersal by larvae, (3) woody hosts, (4) extreme polyphagy, (5) high abundance, resulting in status as economic pests, (6) invasiveness, and (7) obligate parthenogenesis in some populations. If extreme polyphagy is defined as feeding on 20 or more families of hostplants, this syndrome is found convergently in several species of bagworm moths, tussock moths, root weevils, and 5 families of scale insects. We hypothesize that extreme polyphagy in these taxa results from "niche explosion", a positive feedback loop connecting large population size to broad host range. The niche explosion has a demographic component (sometimes called the "amplification effect" in studies of pathogens) as well as a population-genetic component, due mainly to the increased effectiveness of natural selection in larger populations. The frequent origins of parthenogenesis in extreme polyphages are, in our interpretation, a consequence of this increased effectiveness of natural selection and consequent reduced importance of sexuality. The niche explosion hypothesis makes detailed predictions about the comparative genomics and population genetics of extreme polyphages and related specialists. It has a number of potentially important implications, including an explanation for the lack of observed trade-offs between generalists and specialists, a re-interpretation of the ecological correlates of parthenogenesis, and a general expectation that Malthusian population explosions may be amplified by Darwinian effects.

  4. SOLID PHASE MICROEXTRACTION SAMPLING OF HIGH EXPLOSIVE RESIDUES IN THE PRESENCE OF RADIONUCLIDES AND RADIONUCLIDE SURROGATE METALS

    SciTech Connect

    Duff, M; S Crump, S; Robert02 Ray, R; Donna Beals, D

    2007-04-13

    The Federal Bureau of Investigation (FBI) Laboratory currently does not have on site facilities for handling radioactive evidentiary materials and there are no established FBI methods or procedures for decontaminating high explosive (HE) evidence while maintaining evidentiary value. One experimental method for the isolation of HE residue involves using solid phase microextraction or SPME fibers to remove residue of interest. Due to their high affinity for organics, SPME fibers should have little affinity for most metals. However, no studies have measured the affinity of radionuclides for SPME fibers. The focus of this research was to examine the affinity of dissolved radionuclide ({sup 239/240}Pu, {sup 238}U, {sup 237}Np, {sup 85}Sr, {sup 133}Ba, {sup 137}Cs, {sup 60}Co and {sup 226}Ra) and stable radionuclide surrogate metals (Sr, Co, Ir, Re, Ni, Ba, Cs, Nb, Zr, Ru, and Nd) for SPME fibers at the exposure conditions that favor the uptake of HE residues. Our results from radiochemical and mass spectrometric analyses indicate these metals have little measurable affinity for these SPME fibers during conditions that are conducive to HE residue uptake with subsequent analysis by liquid or gas phase chromatography with mass spectrometric detection.

  5. Preliminary experiments using light-initiated high explosive for driving thin flyer plates. [SASN

    SciTech Connect

    Benham, R.A.

    1980-02-01

    Light-initiated high explosive, silver acelytide - silver-nitrate (SASN), has been used to produce simulated x ray blow-off impulse loading on reentry vehicles to study the system structural response. SASN can be used to accelerate thin flyer plates to high terminal velocities which, in turn, can deliver a pressure pulse that can be tailored to the target material. This process is important for impulse tests where both structural and material response is desired. The theories used to calculate the dynamic state of the flyer plate prior to impact are summarized. Data from several experiments are presented which indicate that thin flyer plates can be properly accelerated and that there are predictive techniques available which are adequate to calculate the motion of the flyer plate. Recommendations are made for future study that must be undertaken to make the SASN flyer plate technique usable.

  6. Computational study of 3-D hot-spot initiation in shocked insensitive high-explosive

    NASA Astrophysics Data System (ADS)

    Najjar, F. M.; Howard, W. M.; Fried, L. E.; Manaa, M. R.; Nichols, A., III; Levesque, G.

    2012-03-01

    High-explosive (HE) material consists of large-sized grains with micron-sized embedded impurities and pores. Under various mechanical/thermal insults, these pores collapse generating hightemperature regions leading to ignition. A hydrodynamic study has been performed to investigate the mechanisms of pore collapse and hot spot initiation in TATB crystals, employing a multiphysics code, ALE3D, coupled to the chemistry module, Cheetah. This computational study includes reactive dynamics. Two-dimensional high-resolution large-scale meso-scale simulations have been performed. The parameter space is systematically studied by considering various shock strengths, pore diameters and multiple pore configurations. Preliminary 3-D simulations are undertaken to quantify the 3-D dynamics.

  7. Shock waves raised by explosions in space as sources of ultra-high-energy cosmic rays

    NASA Astrophysics Data System (ADS)

    Kichigin, Gennadiy

    2015-03-01

    The paper discusses the possibility of particle acceleration up to ultrahigh energies in the relativistic waves generated by various explosive processes in the interstellar medium. We propose to use the surfatron mechanism of acceleration (surfing) of charged particles trapped in the front of relativistic waves as a generator of high-energy cosmic rays (CRs). Conditions under which surfing in these waves can be made are studied thoroughly. Ultra-high-energy CRs (up to 10^20 eV) are shown to be obtained due to the surfing in the relativistic plane and spherical waves. Surfing is supposed to take place in nonlinear Langmuir waves excited by powerful electromagnetic radiation or relativistic beams of charged particles, as well as in strong shock waves generated by relativistic jets or spherical formations that expand fast (fireballs).

  8. Harvesting materials formed under extreme conditions: Synthesis and isolation of nanocarbons derived from detonation of high explosives

    NASA Astrophysics Data System (ADS)

    Firestone, Millicent; Ringstrand, Bryan; Huber, Rachel; Dattelbaum, Dana; Gustavson, Richard; Podlesak, David

    High explosive detonation products are primarily composed of molecular gases and solid carbon products. Recent studies have shown that the solid carbon condensate morphologies can vary depending on the high explosive and / or the pressure, temperature, or environment of the detonation. These studies have revealed, for example, unique carbon nanoparticles possessing novel morphologies, such as ones composed of hollow cores surrounded by lamellar structured graphitic shells. Despite these observations little work has been done to isolate these particles from the recovered post-detonation soot. This lack of effort to isolate and purify these products limits our understanding of their materials properties and, ultimately our ability to adapt them for useful materials. Herein, we report our recent studies directed at the production of nano-carbons through the detonation of a high explosive (e.g., composition B) under a range of experimental conditions. We further describe work directed at isolation and purification of the carbon nanoparticles.

  9. Enhanced mass removal due to phase explosion during high irradiance nanosecond laser ablation of silicon

    SciTech Connect

    Yoo, Jong Hyun

    2000-05-20

    The morphology of craters resulting from high irradiance laser ablation of silicon was measured using a white light interferometry microscope. The craters show a dramatic increase in their depth and volume at a certain irradiance, indicating a change in the primary mechanism for mass removal. Laser shadowgraph imaging was used to characterize and differentiate the mass ejection processes for laser irradiances above and below the threshold value. Time-resolved images show distinct features of the mass ejected at irradiances above the threshold value including the presence of micron-sized particulates; this begins at approximately 300 {approx} 400 ns after the start of laser heating. The analysis of the phenomena was carried out by using two models: a thermal evaporation model and a phase explosion model. Estimation of the crater depth due to the thermally evaporated mass led to a large underestimation of the crater depth for irradiances above the threshold. Above the threshold irradiance, the possibility of phase explosion was analyzed. Two important results are the thickness of the superheated liquid layer that is close to the critical temperature and the time for vapor bubbles that are generated in the superheated liquid to achieve a critical size. After reaching the critical size, vapor bubbles can grow spontaneously resulting in a violent ejection of liquid droplets from the superheated volume. The effects of an induced transparency, i.e. of liquid silicon turning into an optically transparent liquid dielectric medium, are also introduced. The estimated time for a bubble to reach the critical size is in agreement with the delay time measured for the initiation of large mass ejection. Also, the thickness of the superheated liquid layer that is close to the critical temperature at the time of the beginning of the large mass ejection is representative of the crater depth at the threshold irradiance. These results suggest that phase explosion is a plausible thermal

  10. Central fatigue contributes to the greater reductions in explosive than maximal strength with high-intensity fatigue.

    PubMed

    Buckthorpe, Matthew; Pain, Matthew T G; Folland, Jonathan P

    2014-07-01

    The study aimed to assess the influence of fatigue induced by repeated high-force explosive contractions on explosive and maximal isometric strength of the human knee extensors and to examine the neural and contractile mechanisms for the expected decrement. Eleven healthy untrained males completed 10 sets of voluntary maximal explosive contractions (five times 3 s, interspersed with 2 s rest). Sets were separated by 5 s, during which supramaximal twitch and octet contractions [eight pulses at 300 Hz that elicit the contractile peak rate of force development (pRFD)] were evoked. Explosive force, at specific time points, and pRFD were assessed for voluntary and evoked efforts, expressed in absolute terms and normalized to maximal/peak force. Maximal voluntary contraction force (MVCF) and peak evoked forces were also determined. Surface EMG amplitude was measured from three superficial agonists and normalized to maximal compound action potential area. By set 10, explosive force (47-52%, P < 0.001) and MVCF (42%, P < 0.001) had declined markedly. Explosive force declined more rapidly than MVCF, with lower normalized explosive force at 50 ms (29%, P = 0.038) that resulted in reduced normalized explosive force from 0 to 150 ms (11-29%, P ≤ 0.038). Neural efficacy declined by 34%, whilst there was a 15-28% reduction in quadriceps EMG amplitude during voluntary efforts (all P ≤ 0.03). There was demonstrable contractile fatigue (pRFD: octet, 27%; twitch, 66%; both P < 0.001). Fatigue reduced normalized pRFD for the twitch (21%, P = 0.001) but not the octet (P = 0.803). Fatigue exerted a more rapid and pronounced effect on explosive force than on MVCF, particularly during the initial 50 ms of contraction, which may explain the greater incidence of injuries associated with fatigue. Both neural and contractile fatigue mechanisms appeared to contribute to impaired explosive voluntary performance.

  11. A simple but highly efficient multi-formyl phenol-amine system for fluorescence detection of peroxide explosive vapour.

    PubMed

    Xu, Wei; Fu, Yanyan; Gao, Yixun; Yao, Junjun; Fan, Tianchi; Zhu, Defeng; He, Qingguo; Cao, Huimin; Cheng, Jiangong

    2015-07-11

    A simple, highly stable, sensitive and selective fluorescent system for peroxide explosives was developed via an aromatic aldehyde oxidation reaction. The high efficiency arises from its higher HOMO level and multiple H-bonding. The sensitivity is obtained to be 0.1 ppt for H2O2 and 0.2 ppb for TATP. PMID:26054635

  12. High-Speed Photographic Experiments To Investigate The Effects Of Booster Housing Geometry On The Detonability Of Secondary Explosives

    NASA Astrophysics Data System (ADS)

    Hutchinson, C. D.

    1985-02-01

    Warheads in conventional munitions contain three explosive components - a detonator, an augmenting charge known as a booster and a main filling. High-speed photographic experiments have indicated that a significant improvement in the initiating ability of boosters can be obtained if minor modifications are made to their containers, or housings. It is shown that in the situation where an aluminium alloy booster housing is inserted into a recess in the main filling, enhanced radial initiation can be achieved. This is especially welcome where insensitive plastic bonded high explosives are used as main charge fillings.

  13. Tin particle size measurements in high explosively driven shockwave experiments using Mie scattering method

    NASA Astrophysics Data System (ADS)

    Monfared, Shabnam; Buttler, William; Schauer, Martin; Lalone, Brandon; Pack, Cora; Stevens, Gerald; Stone, Joseph; Special Technologies Laboratory Collaboration; Los Alamos National Laboratory Team

    2014-03-01

    Los Alamos National Laboratory is actively engaged in the study of material failure physics to support the hydrodynamic models development, where an important failure mechanism of explosively shocked metals causes mass ejection from the backside of a shocked surface with surface perturbations. Ejecta models are in development for this situation. Our past work has clearly shown that the total ejected mass and mass-velocity distribution sensitively link to the wavelength and amplitude of these perturbations. While we have had success developing ejecta mass and mass-velocity models, we need to better understand the size and size-velocity distributions of the ejected mass. To support size measurements we have developed a dynamic Mie scattering diagnostic based on a CW laser that permits measurement of the forward attenuation cross-section combined with a dynamic mass-density and mass-velocity distribution, as well as a measurement of the forward scattering cross-section at 12 angles (5- 32.5 degrees) in increments of 2.5 degrees. We compare size distribution followed from Beers law with attenuation cross-section and mass measurement to the dynamic size distribution determined from scattering cross-section alone. We report results from our first quality experiments.

  14. High-energy particle acceleration by explosive electromagnetic interaction in an accretion disk

    NASA Technical Reports Server (NTRS)

    Haswell, C. A.; Tajima, T.; Sakai, J.-I.

    1992-01-01

    By examining electromagnetic field evolution occurring in an accretion disk around a compact object, we arrive at an explosive mechanism of particle acceleration. Flux-freezing in the differentially rotating disk causes the seed and/or generated magnetic field to wrap up tightly, becoming highly sheared and locally predominantly azimuthal in orientation. We show how asymptotically nonlinear solutions for the electromagnetic fields may arise in isolated plasma blobs as a result of the driving of the fluid equations by the accretion flow. These fields are capable of rapidly accelerating charged particles from the disk. Acceleration through the present mechanism from AGN can give rise to energies beyond 10 exp 20 eV. Such a mechanism may present an explanation for the extragalactic origin of the most energetic observed cosmic rays.

  15. Deflagration Rate Measurements of Three Insensitive High Explosives: LLM-105, TATB, and DAAF

    SciTech Connect

    Glascoe, E A; Maienschein, J L; Lorenz, K T; Tan, N; Koerner, J G

    2010-03-08

    The pressure dependent deflagration rates of LLM-105, DAAF and TATB based formulations were measured in the LLNL high pressure strand burner. The role of binder amount, explosive type, and thermal damage and their effects on the deflagration rate will be discussed. One DAAF formulation, two different formulations of LLM-105, and four formulations of TATB were studied; results indicate that binder amount and type play a minor role in the deflagration behavior. This is in sharp contrast to the HMX based formulations which strongly depend on binder amount and type. The effect of preheating these samples was considerably more dramatic. In the case of LLM-105, preheating the sample appears to have little effect on the deflagration rate. In contrast, preheating DAAF and TATB formulations causes the deflagration rate to accelerate. The thermal and mechanical properties of these formulations will be discussed in the context of their pressure and temperature dependent deflagration rates.

  16. A thermalized ion explosion model for high energy sputtering and track registration

    NASA Technical Reports Server (NTRS)

    Seiberling, L. E.; Griffith, J. E.; Tombrello, T. A.

    1980-01-01

    A velocity spectrum of neutral sputtered particles as well as a low resolution mass spectrum of sputtered molecular ions was measured for 4.74 MeV F-19(+2) incident of UF4. The velocity spectrum is dramatically different from spectra taken with low energy (keV) bombarding ions, and is shown to be consistent with a hot plasma of atoms in thermal equilibrium inside the target. A thermalized ion explosion model is proposed for high energy sputtering which is expected to describe track formation in dielectric materials. The model is shown to be consistent with the observed total sputtering yield and the dependence of the yield on the primary ionization rate of the incident ion.

  17. A logic model for cook-off phenomenology in high explosives

    SciTech Connect

    Eisenhawer, S. W.; Bott, T. F.; Luck, L. B.; Kingson, J.; Key, B. P.

    2003-01-01

    Logic models are valuable tools in the development of predictive models for complex physical processes. The use of deductive logic in the form of a possibility tree makes it straightforward to develop a comprehensive set of unique, alternative paths that describe the system. We demonstrate the power of this approach for the complex process of cook-off of high explosives (HE). The possibility tree describes the causal paths from heating HE to the alternative end states. One of these end states is a violent reaction. Conversion of the tree to the equivalent digraph yields a valuable visualization tool for examining the relationships between sub-processes and provides a sound framework for the development of analytical models.

  18. Explosives signatures and analysis

    NASA Astrophysics Data System (ADS)

    Fountain, Augustus Way, III; Oyler, Jonathan M.; Ostazeski, Stanley A.

    2008-04-01

    The challenge of sampling explosive materials for various high threat military and civilian operational scenarios requires the community to identify and exploit other chemical compounds within the mixtures that may be available to support stand-off detection techniques. While limited surface and vapor phase characterization of IEDs exist, they are insufficient to guide the future development and evaluation of field deployable explosives detection (proximity and standoff) capabilities. ECBC has conducted a limited investigation of three artillery ammunition types to determine what chemical vapors, if any, are available for sensing; the relative composition of the vapors which includes the more volatile compounds in munitions, i.e., plastersizers and binders; and the sensitivity needed detect these vapors at stand-off. Also in partnership with MIT-Lincoln Laboratory, we performed a background measurement campaign at the National Training Center to determine the baseline ambient amounts and variability of nitrates and nitro-ester compounds as vapors, particulates, and on surfaces; as well as other chemical compounds related to non-energetic explosive additives. Environmental persistence studies in contexts relevant to counter-IED sensing operations, such as surface residues, are still necessary.

  19. Development and applications of rectangular box-type explosively bonded structures for high-heat-load beamline components

    NASA Astrophysics Data System (ADS)

    Shu, D.; Chang, J.; Kuzay, T. M.; Brasher, D. G.

    2001-07-01

    Explosive bonding technology is a good choice to join dissimilar materials, such as 304L stainless steel and GlidCop AL-15, and is used extensively in making the advanced photon source (APS) high-heat-load beamline and front-end components. It is a bonding method in which the controlled energy of a detonating explosive is used to create a metallurgical bond between two or more similar or dissimilar materials. In recent years, special explosive bonding units with rectangular box-type joints were developed for the APS new high-heat-load beamline components. Based on this new technique, the box form of the component could be built in two halves first, then welded together. Therefore, beamline designers have more freedom to optimize the cooling surface geometry.

  20. On beyond the standard model for high explosives: challenges & obstacles to surmount

    SciTech Connect

    Menikoff, Ralph Ds

    2009-01-01

    Plastic-bonded explosives (PBX) are heterogeneous materials. Nevertheless, current explosive models treat them as homogeneous materials. To compensate, an empirically determined effective burn rate is used in place of a chemical reaction rate. A significant limitation of these models is that different burn parameters are needed for applications in different regimes; for example, shock initiation of a PBX at different initial temperatures or different initial densities. This is due to temperature fluctuations generated when a heterogeneous material is shock compressed. Localized regions of high temperatures are called hot spots. They dominate the reaction for shock initiation. The understanding of hot spot generation and their subsequent evolution has been limited by the inability to measure transients on small spatial ({approx} 1 {micro}m) and small temporal ({approx} 1 ns) scales in the harsh environment of a detonation. With the advances in computing power, it is natural to try and gain an understanding of hot-spot initiation with numerical experiments based on meso-scale simulations that resolve material heterogeneities and utilize realistic chemical reaction rates. However, to capture the underlying physics correctly, such high resolution simulations will require more than fast computers with a large amount of memory. Here we discuss some of the issues that need to be addressed. These include dissipative mechanisms that generate hot spots, accurate thermal propceties for the equations of state of the reactants and products, and controlling numerical entropy error from shock impedance mismatches at material interfaces. The later can generate artificial hot spots and lead to premature reaction. Eliminating numerical hot spots is critical for shock initiation simulations due to the positive feedback between the energy release from reaction and the hydrodynamic flow.

  1. A case study of a transported bromine explosion event in the Canadian high arctic

    NASA Astrophysics Data System (ADS)

    Zhao, X.; Strong, K.; Adams, C.; Schofield, R.; Yang, X.; Richter, A.; Friess, U.; Blechschmidt, A.-M.; Koo, J.-H.

    2016-01-01

    Ozone depletion events in the polar troposphere have been linked to extremely high concentrations of bromine, known as bromine explosion events (BEE). However, the optimum meteorological conditions for the occurrence of these events remain uncertain. On 4-5 April 2011, a combination of both blowing snow and a stable shallow boundary layer was observed during a BEE at Eureka, Canada (86.4°W, 80.1°N). Measurements made by a Multi-Axis Differential Optical Absorption Spectroscopy spectrometer were used to retrieve BrO profiles and partial columns. During this event, the near-surface BrO volume mixing ratio increased to ~20 parts per trillion by volume, while ozone was depleted to ~1 ppbv from the surface to 700 m. Back trajectories and Global Ozone Monitoring Experiment-2 satellite tropospheric BrO columns confirmed that this event originated from a bromine explosion over the Beaufort Sea. From 30 to 31 March, meteorological data showed high wind speeds (24 m/s) and elevated boundary layer heights (~800 m) over the Beaufort Sea. Long-distance transportation (~1800 km over 5 days) to Eureka indicated strong recycling of BrO within the bromine plume. This event was generally captured by a global chemistry-climate model when a sea-salt bromine source from blowing snow was included. A model sensitivity study indicated that the surface BrO at Eureka was controlled by both local photochemistry and boundary layer dynamics. Comparison of the model results with both ground-based and satellite measurements confirmed that the BEE observed at Eureka was triggered by transport of enhanced BrO from the Beaufort Sea followed by local production/recycling under stable atmospheric shallow boundary layer conditions.

  2. Abiotic transformation of high explosives by freshly precipitated iron minerals in aqueous FeII solutions.

    PubMed

    Boparai, Hardiljeet K; Comfort, Steve D; Satapanajaru, Tunlawit; Szecsody, Jim E; Grossl, Paul R; Shea, Patrick J

    2010-05-01

    Zerovalent iron barriers have become a viable treatment for field-scale cleanup of various ground water contaminants. While contact with the iron surface is important for contaminant destruction, the interstitial pore water within and near the iron barrier will be laden with aqueous, adsorbed and precipitated Fe(II) phases. These freshly precipitated iron minerals could play an important role in transforming high explosives (HE). Our objective was to determine the transformation of RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine), HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine), and TNT (2,4,6-trinitrotoluene) by freshly precipitated iron Fe(II)/Fe(III) minerals. This was accomplished by quantifying the effects of initial Fe(II) concentration, pH, and the presence of aquifer solids (Fe(III) phases) on HE transformation rates. Results showed that at pH 8.2, freshly precipitated iron minerals transformed RDX, HMX, and TNT with reaction rates increasing with increasing Fe(II) concentrations. RDX and HMX transformations in these solutions also increased with increasing pH (5.8-8.55). By contrast, TNT transformation was not influenced by pH (6.85-8.55) except at pH values <6.35. Transformations observed via LC/MS included a variety of nitroso products (RDX, HMX) and amino degradation products (TNT). XRD analysis identified green rust and magnetite as the dominant iron solid phases that precipitated from the aqueous Fe(II) during HE treatment under anaerobic conditions. Geochemical modeling also predicted Fe(II) activity would likely be controlled by green rust and magnetite. These results illustrate the important role freshly precipitated Fe(II)/Fe(III) minerals in aqueous Fe(II) solutions play in the transformation of high explosives. PMID:20226494

  3. Measuring the Energy Release of Low Amplitude Impact of High Explosive Events

    NASA Astrophysics Data System (ADS)

    Straight, J. W.; Idar, D. J.; Smith, L.; Osborn, M. A.; Viramontes, L. E.; Chavez, P. J.

    2004-07-01

    Predicting the degree of violence of high explosive (HE) reactions for a given event is desirable for risk assessments and a goal for computational models. Historically, different types of low amplitude impact tests on HE specimens have been performed to determine the critical impact-velocity threshold for high explosive violent reactions (HEVR). Additionally, the energy release relative to a steady-state detonation is also desirable for assessing the potential outcome of an accidental event. Traditionally, blast gauge measurements have been used to measure the overpressure of the HEVR event at a defined distance. This paper summarizes the use of this active technique coupled with a passive technique to derive average energy release curves for Modified Steven tests. A classic ballistic pendulum design was employed with the traditional blast gauge method. Calibration of the ballistic pendulum involved three elements. First, two mechanical measurements were related to the actual peak swing of the pendulum. Second, the general nature of the swing versus energy release curve was estimated. Two different approaches were used to estimate the momenta as a function of HE energy release using the Gurney relationships for an unsymmetrical sandwich. Finally, both techniques were simultaneously benchmarked with PBX 9501 calibration charges. Test results demonstrate the utility of using coupled diagnostic methods for low amplitude insult testing. Each set of data was fit to derive a working curve for the determination of the average energy release for HEVR event based on mass relative to a steady-state detonation. These tests results and working curve derivations are presented.

  4. Abiotic transformation of high explosives by freshly precipitated iron minerals in aqueous FeII solutions.

    PubMed

    Boparai, Hardiljeet K; Comfort, Steve D; Satapanajaru, Tunlawit; Szecsody, Jim E; Grossl, Paul R; Shea, Patrick J

    2010-05-01

    Zerovalent iron barriers have become a viable treatment for field-scale cleanup of various ground water contaminants. While contact with the iron surface is important for contaminant destruction, the interstitial pore water within and near the iron barrier will be laden with aqueous, adsorbed and precipitated Fe(II) phases. These freshly precipitated iron minerals could play an important role in transforming high explosives (HE). Our objective was to determine the transformation of RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine), HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine), and TNT (2,4,6-trinitrotoluene) by freshly precipitated iron Fe(II)/Fe(III) minerals. This was accomplished by quantifying the effects of initial Fe(II) concentration, pH, and the presence of aquifer solids (Fe(III) phases) on HE transformation rates. Results showed that at pH 8.2, freshly precipitated iron minerals transformed RDX, HMX, and TNT with reaction rates increasing with increasing Fe(II) concentrations. RDX and HMX transformations in these solutions also increased with increasing pH (5.8-8.55). By contrast, TNT transformation was not influenced by pH (6.85-8.55) except at pH values <6.35. Transformations observed via LC/MS included a variety of nitroso products (RDX, HMX) and amino degradation products (TNT). XRD analysis identified green rust and magnetite as the dominant iron solid phases that precipitated from the aqueous Fe(II) during HE treatment under anaerobic conditions. Geochemical modeling also predicted Fe(II) activity would likely be controlled by green rust and magnetite. These results illustrate the important role freshly precipitated Fe(II)/Fe(III) minerals in aqueous Fe(II) solutions play in the transformation of high explosives.

  5. Explosives tester

    DOEpatents

    Haas, Jeffrey S.; Howard, Douglas E.; Eckels, Joel D.; Nunes, Peter J.

    2011-01-11

    An explosives tester that can be used anywhere as a screening tool by non-technical personnel to determine whether a surface contains explosives. First and second explosives detecting reagent holders and dispensers are provided. A heater is provided for receiving the first and second explosives detecting reagent holders and dispensers.

  6. Analysis and modeling of flow blockage-induced steam explosion events in the High-Flux Isotope Reactor

    SciTech Connect

    Taleyarkhan, R.P.; Georgevich, V.; Lestor, C.W.; Gat, U.; Lepard, B.L.; Cook, D.H.; Freels, J.; Chang, S.J.; Luttrell, C.; Gwaltney, R.C.; Kirkpatrick, J.

    1993-06-01

    This paper provides a perspective overview of the analysis and modeling work done to evaluate the threat from steam explosion loads in the High-Flux Isotope Reactor during flow blockage events. The overall workscope included modeling and analysis of core melt initiation, melt propagation, bounding and best-estimate steam explosion energetics, vessel failure from fracture, bolts failure from exceedance of elastic limits, and finally, missile evolution and transport. Aluminum ignition was neglected. Evaluations indicated that a thermally driven steam explosion with more than 65 MJ of energy insertion in the core region over several miliseconds would be needed to cause a sufficiently energetic missile with a capacity to cause early confinement failure. This amounts to about 65% of the HFIR core mass melting and participating in a steam explosion. Conservative melt propagation analyses have indicated that at most only 24% of the HFIR core mass could melt during flow blockage events under full-power conditions. Therefore, it is judged that the HFIR vessel and top head structure will be able to withstand loads generated from thermally driven steam explosions initiated by any credible flow blockage event. A substantial margin to safety was demonstrated.

  7. Analysis and modeling of flow blockage-induced steam explosion events in the High-Flux Isotope Reactor

    SciTech Connect

    Taleyarkhan, R.P.; Georgevich, V.; Lestor, C.W.; Gat, U.; Lepard, B.L.; Cook, D.H.; Freels, J.; Chang, S.J.; Luttrell, C.; Gwaltney, R.C.; Kirkpatrick, J.

    1993-01-01

    This paper provides a perspective overview of the analysis and modeling work done to evaluate the threat from steam explosion loads in the High-Flux Isotope Reactor during flow blockage events. The overall workscope included modeling and analysis of core melt initiation, melt propagation, bounding and best-estimate steam explosion energetics, vessel failure from fracture, bolts failure from exceedance of elastic limits, and finally, missile evolution and transport. Aluminum ignition was neglected. Evaluations indicated that a thermally driven steam explosion with more than 65 MJ of energy insertion in the core region over several miliseconds would be needed to cause a sufficiently energetic missile with a capacity to cause early confinement failure. This amounts to about 65% of the HFIR core mass melting and participating in a steam explosion. Conservative melt propagation analyses have indicated that at most only 24% of the HFIR core mass could melt during flow blockage events under full-power conditions. Therefore, it is judged that the HFIR vessel and top head structure will be able to withstand loads generated from thermally driven steam explosions initiated by any credible flow blockage event. A substantial margin to safety was demonstrated.

  8. Laboratories & Classrooms For High School Physics.

    ERIC Educational Resources Information Center

    Palmer, R. Ronald; Rice, William Maxwell

    Information and recommendations are presented to assist school planners in designing facilities for physics. Emphasis is given to design features related to the conduct of laboratory experiments by students, television teaching of physics, new physics courses, classroom demonstrations, equipment storage and preparation areas, and combined…

  9. The preparation and ethanol fermentation of high-concentration sugars from steam-explosion corn stover.

    PubMed

    Xie, Hui; Wang, Fengqin; Yin, Shuangyao; Ren, Tianbao; Song, Andong

    2015-05-01

    In the field of biofuel ethanol, high-concentration- reducing sugars made from cellulosic materials lay the foundation for high-concentration ethanol fermentation. In this study, corn stover was pre-treated in a process combining chemical methods and steam explosion; the cellulosic hydrolyzed sugars obtained by fed-batch saccharification were then used as the carbon source for high-concentration ethanol fermentation. Saccharomyces cerevisiae 1308, Angel yeast, and Issatchenkia orientalis were shake-cultured with Pachysolen tannophilus P-01 for fermentation. Results implied that the ethanol yields from the three types of mixed strains were 4.85 g/100 mL, 4.57 g/100 mL, and 5.02 g/100 mL (separately) at yield rates of 91.6, 89.3, and 92.2%, respectively. Therefore, it was inferred that shock-fermentation using mixed strains achieved a higher ethanol yield at a greater rate in a shorter fermentation period. This study provided a theoretical basis and technical guidance for the fermentation of industrial high-concentrated cellulosic ethanol.

  10. Ablation-induced explosion of metal using a high-power Nd:YAG laser

    NASA Astrophysics Data System (ADS)

    Yoh, Jack J.; Lee, Hyunhee; Choi, Jihee; Lee, Kyung-cheol; Kim, Ki-hong

    2008-02-01

    The interaction of a high-power pulsed-laser beam with metal targets in air from a 1.06 μm, 5 ns, 3 J/pulse, Nd:YAG pulsed laser is investigated together with hydrodynamic theories of laser-supported blast wave and multimaterial reactive Euler equations. The high-speed blast wave generated by the laser ablation of metal reaches a maximum velocity of several thousand meters per second. The apparently similar flow conditions to those of reactive shock wave allow one to apply the equations of motion for energetic materials and to understand the explosive behavior of metal vaporization upon laser ablation. The characteristic time at which the planar to spherical wave transition occurs is investigated at low (20 mJ/pulse) to high (200 mJ/pulse) beam intensities. The flow structure behind the leading shock wave during the early planar shock state is confirmed by the high-resolution multimaterial hydrocode originally developed for shock compression of condensed matter. A repeatable lab-scale blast wave experiment is conducted at various energy levels with three different ablative targets, and both theoretical and computational analyses are used to verify the flow structures behind the leading shock front that remains spherically symmetric until all the momentum transferred from the absorbed intensity dissipates into open air a few microseconds later.

  11. Fabrication of Optical Fiber Mechanical Shock Sensors for the Los Alamos HERT (High Explosive Radio Telemetry) Project

    SciTech Connect

    P. E. Klingsporn

    2005-11-14

    This document lists the requirements for the fiber optic mechanical shock sensor for the Los Alamos HERT (High Explosive Radio Telemetry) project and provides detailed process steps for fabricating, testing, and assembling the fiber shock sensors for delivery to Los Alamos.

  12. Demonstration of submersible high-throughput microfluidic immunosensors for underwater explosives detection.

    PubMed

    Adams, André A; Charles, Paul T; Deschamps, Jeffrey R; Kusterbeck, Anne W

    2011-11-15

    Significant security threats posed by highly energetic nitroaromatic compounds in aquatic environments and the demilitarization and pending cleanup of areas previously used for munitions manufacture and storage represent a challenge for less expensive, faster, and more sensitive systems capable of analyzing groundwater and seawater samples for trace levels of explosive materials. Presented here is an inexpensive high throughput microfluidic immunosensor (HTMI) platform intended for the rapid, highly selective quantitation of nitroaromatic compounds in the field. Immunoaffinity and fluorescence detection schemes were implemented in tandem on a novel microfluidic device containing 39 parallel microchannels that were 500 μm tall, 250 μm wide, and 2.54 cm long with covalently tethered antibodies that was engineered for high-throughput high-volume sample processing. The devices were produced via a combination of high precision micromilling and hot embossing. Mass transfer limitations were found in conventional microsystems and were minimized due to higher surface area to volume ratios that exceeded those possessed by conventional microdevices and capillaries. Until now, these assays were limited to maximum total volume flow rates of ~1 mL/min due in part to kinetics and high head pressures of single microchannels. In the design demonstrated here, highly parallelized microchannels afforded up to a 100-fold increase in total volume flow rate while maintaining favorable kinetic constraints for efficient antigen-antibody interaction. The assay employed total volume throughput of up to 6 mL/min while yielding signal-to-noise ratios of >15 in all cases. In addition to samples being processed up to 60 times faster than in conventional displacement-based immunoassays, the current system was capable of quantitating 0.01 ng/mL TNT samples without implementing offline preconcentration, thereby, demonstrating the ability to improve sensitivity by as much as 2 orders of magnitude

  13. Demonstration of submersible high-throughput microfluidic immunosensors for underwater explosives detection.

    PubMed

    Adams, André A; Charles, Paul T; Deschamps, Jeffrey R; Kusterbeck, Anne W

    2011-11-15

    Significant security threats posed by highly energetic nitroaromatic compounds in aquatic environments and the demilitarization and pending cleanup of areas previously used for munitions manufacture and storage represent a challenge for less expensive, faster, and more sensitive systems capable of analyzing groundwater and seawater samples for trace levels of explosive materials. Presented here is an inexpensive high throughput microfluidic immunosensor (HTMI) platform intended for the rapid, highly selective quantitation of nitroaromatic compounds in the field. Immunoaffinity and fluorescence detection schemes were implemented in tandem on a novel microfluidic device containing 39 parallel microchannels that were 500 μm tall, 250 μm wide, and 2.54 cm long with covalently tethered antibodies that was engineered for high-throughput high-volume sample processing. The devices were produced via a combination of high precision micromilling and hot embossing. Mass transfer limitations were found in conventional microsystems and were minimized due to higher surface area to volume ratios that exceeded those possessed by conventional microdevices and capillaries. Until now, these assays were limited to maximum total volume flow rates of ~1 mL/min due in part to kinetics and high head pressures of single microchannels. In the design demonstrated here, highly parallelized microchannels afforded up to a 100-fold increase in total volume flow rate while maintaining favorable kinetic constraints for efficient antigen-antibody interaction. The assay employed total volume throughput of up to 6 mL/min while yielding signal-to-noise ratios of >15 in all cases. In addition to samples being processed up to 60 times faster than in conventional displacement-based immunoassays, the current system was capable of quantitating 0.01 ng/mL TNT samples without implementing offline preconcentration, thereby, demonstrating the ability to improve sensitivity by as much as 2 orders of magnitude

  14. A study of phase explosion of metal using high power Nd:YAG laser ablation

    SciTech Connect

    Yoh, Jack J.; Lee, H. H.; Choi, J. H.; Lee, K. C.; Kim, K. H.

    2007-12-12

    The interaction of high-power pulsed-laser beam with metal targets in air from 1.06 {mu}m, 5 ns, 3 J/pulse max, Nd:YAG pulsed laser is investigated together with hydrodynamic theories of laser-supported detonation (LSD) wave and multi-material reactive Euler equations. The high speed blast wave generated by the laser ablation of metal reaches maximum velocity of several thousand meters per second. The apparently similar flow conditions to those of reactive shock wave allow one to apply the equations of motion for energetic materials and to understand the explosive behavior of metal vaporization upon laser ablation. The characteristic time at which planar to spherical wave transition occurs is confirmed at low (20 mJ/pulse) to higher (200 mJ/pulse) beam intensities. The flow structure behind the leading shock wave during the early planar shock state is confirmed by the high-resolution multi-material hydrocode originally developed for shock compression of condensed matter.

  15. a Study of Phase Explosion of Metal Using High Power Nd:YAG Laser Ablation

    NASA Astrophysics Data System (ADS)

    Yoh, Jack J.; Lee, H. H.; Choi, J. H.; Lee, K. C.; Kim, K. H.

    2007-12-01

    The interaction of high-power pulsed-laser beam with metal targets in air from 1.06 μm, 5 ns, 3 J/pulse max, Nd:YAG pulsed laser is investigated together with hydrodynamic theories of laser-supported detonation (LSD) wave and multi-material reactive Euler equations. The high speed blast wave generated by the laser ablation of metal reaches maximum velocity of several thousand meters per second. The apparently similar flow conditions to those of reactive shock wave allow one to apply the equations of motion for energetic materials and to understand the explosive behavior of metal vaporization upon laser ablation. The characteristic time at which planar to spherical wave transition occurs is confirmed at low (20 mJ/pulse) to higher (200 mJ/pulse) beam intensities. The flow structure behind the leading shock wave during the early planar shock state is confirmed by the high-resolution multi-material hydrocode originally developed for shock compression of condensed matter.

  16. Pressure wave measurements from thermal cook-off of an HMX based high explosive

    SciTech Connect

    Forbes, J W; Tarver, C M; Urtiew, P A; Garcia, F; Greenwood, D W; Vandersall, K S

    2000-10-10

    A better understanding of thermal cook-off is important for safe handling and storing explosive devices. A number of safety issues exist about what occurs when a cased explosive thermally cooks off. For example, violence of the events as a function of confinement are important for predictions of collateral damage. This paper demonstrates how adjacent materials can be gauged to measure the resulting pressure wave and how this wave propagates in this adjacent material. The output pulse from the thermal cook-off explosive containing fixture is of obvious interest for assessing many scenarios.

  17. Pressure Wave Measurements from Thermal Cook-Off of an HMX Based High Explosive PBX 9501

    SciTech Connect

    Garcia, F; Forbes, J W; Tarver, C M; Urtiew, P A; Greenwood, D W; Vandersall, K S

    2001-05-31

    A better understanding of thermal cook-off is important for safe handling and storing explosive devices. A number of safety issues exist about what occurs when a cased explosive thermally cooks off. For example, violence of the events as a function of confinement are important for predictions of collateral damage. This paper demonstrates how adjacent materials can be gauged to measure the resulting pressure wave and how this wave propagates in this adjacent material. The output pulse from the thermal cook-off explosive containing fixture is of obvious interest for assessing many scenarios.

  18. Quantum chemical studies on three novel 1,2,4-triazole N-oxides as potential insensitive high explosives.

    PubMed

    Wu, Qiong; Zhu, Weihua; Xiao, Heming

    2014-09-01

    Three novel explosives were designed by introducing N-oxides into 1,2,4-triazole: 1-amino-3,5-dinitro-1,2,4-triazole-2 N-oxide (ADT2NO), 1-amino-2,5-dinitro-1,2,4-triazole-3 N-oxide (ADT3NO), and 1-amino-3,5-dinitro-1,2,4-triazole-4 N-oxide (ADT4NO). Their detonation performance and sensitivity were estimated by using density functional theory and compared with some famous explosives like 1,3,5,7-tetranitro-1,3,5,7-tetrazocane (HMX) and 1-methyl-2,4,6-trinitrobenzene (TNT). All three designed molecules are more powerful than HMX and less sensitive than TNT, indicating that ADT2NO, ADT3NO, and ADT4NO have high detonation performance as HMX and low sensitivity as TNT, making them being very valuable and may be considered as the potential candidates of insensitive high explosives. Properly introducing N-oxides into the energetic triazole derivatives can generate some superior energetic compounds with both high explosive performance and reduced sensitivity.

  19. Non-detonable and non-explosive explosive simulators

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1997-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable or explodable. The simulator is a combination of an explosive material with an inert material, either in a matrix or as a coating, where the explosive has a high surface ratio but small volume ratio. The simulator has particular use in the training of explosives detecting dogs, calibrating analytical instruments which are sensitive to either vapor or elemental composition, or other applications where the hazards associated with explosives is undesirable but where chemical and/or elemental equivalence is required. The explosive simulants may be fabricated by different techniques. A first method involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and a second method involves coating inert substrates with thin layers of explosive.

  20. Non-detonable and non-explosive explosive simulators

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1997-07-15

    A simulator which is chemically equivalent to an explosive, but is not detonable or explodable is disclosed. The simulator is a combination of an explosive material with an inert material, either in a matrix or as a coating, where the explosive has a high surface ratio but small volume ratio. The simulator has particular use in the training of explosives detecting dogs, calibrating analytical instruments which are sensitive to either vapor or elemental composition, or other applications where the hazards associated with explosives is undesirable but where chemical and/or elemental equivalence is required. The explosive simulants may be fabricated by different techniques. A first method involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and a second method involves coating inert substrates with thin layers of explosive. 11 figs.

  1. High aspect ratio β-MnO2 nanowires and sensor performance for explosive gases

    NASA Astrophysics Data System (ADS)

    Xiao, J.; Liu, P.; Liang, Y.; Li, H. B.; Yang, G. W.

    2013-08-01

    High aspect ratio β-MnO2 nanowires have been synthesized based on a facile and green technique without any chemical additive. The precursor solution of Mn3O4 nanocrystals was first synthesized by laser ablation of a manganese target in deionized water. Due to the high reactive and fresh surface of Mn3O4 nanocrystals produced by laser ablation in liquid, these nanocrystals were spontaneously assembled into the γ-MnOOH nanowires in the precursor solution after aging at room temperature. The high aspect ratio β-MnO2 nanowires were finally produced by the γ-MnOOH nanowires annealing at 300 °C for 3 h. For the high aspect ratio β-MnO2 nanowires, the high specific surface area is advantaged for gas absorption and the unique tunnel structure is good for gas molecule trapping. A gas sensor was made from the β-MnO2 nanowires for explosive gases. The investigations were carried out for the detection of various concentration of H2 at different temperatures, and the results demonstrated that the fabricated gas sensor can detect H2 down to 20 ppm with the sensitivity of 0.5 at 300 °C and short response time of 10s. For sensing CO and ethanol, the detecting concentration reached to 20 ppm at an operation temperature of 150 and 250 °C, respectively. These results can be comparable to that of the current advanced gas sensors made from metal oxide such as ZnO and SnO2, which showing that high aspect ratio β-MnO2 nanowires can be regarded as desirable candidate materials for fabricating gas sensors.

  2. Novel CE-MS technique for detection of high explosives using perfluorooctanoic acid as a MEKC and mass spectrometric complexation reagent.

    PubMed

    Brensinger, Karen; Rollman, Christopher; Copper, Christine; Genzman, Ashton; Rine, Jacqueline; Lurie, Ira; Moini, Mehdi

    2016-01-01

    To address the need for the forensic analysis of high explosives, a novel capillary electrophoresis mass spectrometry (CE-MS) technique has been developed for high resolution, sensitivity, and mass accuracy detection of these compounds. The technique uses perfluorooctanoic acid (PFOA) as both a micellar electrokinetic chromatography (MEKC) reagent for separation of neutral explosives and as the complexation reagent for mass spectrometric detection of PFOA-explosive complexes in the negative ion mode. High explosives that formed complexes with PFOA included RDX, HMX, tetryl, and PETN. Some nitroaromatics were detected as molecular ions. Detection limits in the high parts per billion range and linear calibration responses over two orders of magnitude were obtained. For proof of concept, the technique was applied to the quantitative analysis of high explosives in sand samples.

  3. Extension and Explosivity during an Eccentric Era of the Early Oregon High Cascades

    NASA Astrophysics Data System (ADS)

    Pitcher, B. W.; Kent, A. J.; Grunder, A.; Duncan, R. A.; Eungard, D. W.

    2015-12-01

    One of the most profound changes that the Cascade arc experienced since its inception ~40 Ma, was an eastward shift in volcanic activity starting at ~7.5 Ma, which initiated the modern High Cascades. The infant stages of this arc are exceptionally well preserved within the Deschutes Fm. (~7.4 - 4.0 Ma) of Central Oregon. In stark contrast to the effusive andesitic eruptions that dominated ancestral Cascade volcanism for the preceding 10 million years, the Deschutes Fm. contains over 120 (uncorrelated) tephra fall units and 130 ignimbrite units, indicating an unusually explosive period of volcanism. Conservative estimates of the cumulative volume for 14 regionally extensive ignimbrites is greater than 80 km3. Furthermore, 40Ar-39Ar dating of plagioclase from 7 ignimbrites indicate that this large volume was erupted in less than 1 million years (6.24 ±0.07 to 5.44 ±0.04 Ma). Glass compositions of pumice (n=718) range from 54 to 76 wt. % SiO2. Most ignimbrites contain multiple pumice populations, including banded pumice, which can span nearly 20 wt. % SiO2, indicating involvement of multiple magma types. Two ignimbrites have a compositional gap between 62 and 68 wt. % SiO2, possibly suggesting mingling of a mafic magma with a silicic one derived from partial crustal melting. Trace element (e.g. Nb, Ce, Th) compositions of rhyolitic pumice differ between northern- and southern-sourced ignimbrites, which may be indicative of disparate crustal sources of partial melts (i.e. Siletzia in the North). In addition, Deschutes Fm. rocks are enriched in FeO* and Zr/Sr compared to Quaternary Cascades, and are more similar to High Lava Plains. These trends and the absence of amphibole within the formation suggests hotter and drier magmatic conditions. We suggest that regional extension contributed to increased basaltic flux, leading to anatexis of previously un-melted crust beneath the new arc axis, thereby producing large volumes of silicic magma during this short explosive

  4. Accidental explosions

    SciTech Connect

    Medard, L.A.

    1989-01-01

    This book presents a survey of accidental explosions, their nature and their causes. It covers the physical and chemical conditions governing accidental explosions, whether in the gas phase, or in the liquid or solid state. The theoretical background of the kinetics and thermochemistry of explosions is outlined, followed by a detailed study of the explosion and detonation properties of both gas and condensed explosives. The author surveys a wide variety of substances in daily use in industry which can give rise to accidental explosions. Their properties and hazards are spelt out in detail, the discussion drawing on a long history of sometimes catastrophic accidents. Includes case studies, tables of physical and chemical data.

  5. Inquiry-Related Tasks in High School Science Laboratory Handbooks.

    ERIC Educational Resources Information Center

    Tamir, Pinchas; Lunetta, Vincent N.

    1981-01-01

    Reviews and compares results of content analysis studies of selected high school science laboratory handbooks using the Laboratory Structure and Task Analysis Inventory (LAI). Findings from two biology, two chemistry, and two physics handbooks indicate highly structured investigations where students perform manipulative and observational…

  6. Study of Explosive Electron Emission from a Pin Cathode Using High Resolution Point-Projection X-Ray Radiography

    NASA Astrophysics Data System (ADS)

    Pikuz, S. A.; Shelkovenko, T. A.; Hammer, D. A.; Parkevich, E. V.; Tilikin, I. N.; Mingaleev, A. R.; Agafonov, A. V.

    2015-11-01

    Most studies of Explosive Electron Emission (EEE) are based on the idea of cathode flares developing after explosion of metal whiskers (micron scale pins) on the cathode surface. The physical state of the pin material, the spatial structure of the explosion and its origin are still a matter of conjecture. In this work we used high-resolution point projection x-ray radiography to observe micron scale pin explosion in a high-current diode. Pin cathodes made from 10-25 micron Cu or Mo wires were placed in gaps in return current circuits of hybrid X-pinches on the XP and BIN pulsers. Pin lengths were varied over a range 1-4 mm and pin-anode gaps within 0.05-3 mm. The diode current and voltage were measured. In experiments with small pin-anode gap (0.1 - 1 mm) development of an expanded dense core of the pin was observed except the pin tip with length 100-200 microns indicating significant energy deposition in the wire material. In experiments with bigger gaps there was no visible wire core expansion within the spatial resolution of the experimental technique. Work at Cornell was supported by the National Nuclear Security Administration Stewardship Sciences Academic Programs under Department of Energy Cooperative Agreement No. DE-NA0001836 and at the Lebedev Institute by the RSF grant 142200273.

  7. 42 CFR 493.1441 - Condition: Laboratories performing high complexity testing; laboratory director.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 5 2012-10-01 2012-10-01 false Condition: Laboratories performing high complexity testing; laboratory director. 493.1441 Section 493.1441 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  8. 42 CFR 493.1441 - Condition: Laboratories performing high complexity testing; laboratory director.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 5 2014-10-01 2014-10-01 false Condition: Laboratories performing high complexity testing; laboratory director. 493.1441 Section 493.1441 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  9. 42 CFR 493.1441 - Condition: Laboratories performing high complexity testing; laboratory director.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 5 2013-10-01 2013-10-01 false Condition: Laboratories performing high complexity testing; laboratory director. 493.1441 Section 493.1441 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  10. 42 CFR 493.1441 - Condition: Laboratories performing high complexity testing; laboratory director.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 5 2011-10-01 2011-10-01 false Condition: Laboratories performing high complexity testing; laboratory director. 493.1441 Section 493.1441 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  11. 42 CFR 493.1441 - Condition: Laboratories performing high complexity testing; laboratory director.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Condition: Laboratories performing high complexity testing; laboratory director. 493.1441 Section 493.1441 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  12. Big Explosives Experimental Facility - BEEF

    SciTech Connect

    2014-10-31

    The Big Explosives Experimental Facility or BEEF is a ten acre fenced high explosive testing facility that provides data to support stockpile stewardship and other national security programs. At BEEF conventional high explosives experiments are safely conducted providing sophisticated diagnostics such as high speed optics and x-ray radiography.

  13. Big Explosives Experimental Facility - BEEF

    ScienceCinema

    None

    2016-07-12

    The Big Explosives Experimental Facility or BEEF is a ten acre fenced high explosive testing facility that provides data to support stockpile stewardship and other national security programs. At BEEF conventional high explosives experiments are safely conducted providing sophisticated diagnostics such as high speed optics and x-ray radiography.

  14. An X-band high-impedance relativistic klystron amplifier with an annular explosive cathode

    NASA Astrophysics Data System (ADS)

    Zhu, Danni; Zhang, Jun; Zhong, Huihuang; Qi, Zumin

    2015-11-01

    The feasibility of employing an annular beam instead of a solid one in the X-band high-impedance relativistic klystron amplifier (RKA) is investigated in theory and simulation. Small-signal theory analysis indicates that the optimum bunching distance, fundamental current modulation depth, beam-coupling coefficient, and beam-loaded quality factor of annular beams are all larger than the corresponding parameters of solid beams at the same beam voltage and current. An annular beam RKA and a solid beam RKA with almost the same geometric parameters are compared in particle-in-cell simulation. Output microwave power of 100 MW, gain of 50 dB, and power conversion efficiency of 42% are obtained in an annular beam RKA. The annular beam needs a 15% lower uniform guiding magnetic field than the solid beam. Our investigations demonstrate that we are able to use a simple annular explosive cathode immersed in a lower uniform magnetic field instead of a solid thermionic cathode in a complicated partially shielding magnetic field for designing high-impedance RKA, which avoids high temperature requirement, complicated electron-optical system, large area convergence, high current density, and emission uniformity for the solid beam. An equivalent method for the annular beam and the solid beam on bunching features is proposed and agrees with the simulation. The annular beam has the primary advantages over the solid beam that it can employ the immersing uniform magnetic field avoiding the complicated shielding magnetic field system and needs a lower optimum guiding field due to the smaller space charge effect.

  15. An X-band high-impedance relativistic klystron amplifier with an annular explosive cathode

    SciTech Connect

    Zhu, Danni; Zhang, Jun Zhong, Huihuang; Qi, Zumin

    2015-11-15

    The feasibility of employing an annular beam instead of a solid one in the X-band high-impedance relativistic klystron amplifier (RKA) is investigated in theory and simulation. Small-signal theory analysis indicates that the optimum bunching distance, fundamental current modulation depth, beam-coupling coefficient, and beam-loaded quality factor of annular beams are all larger than the corresponding parameters of solid beams at the same beam voltage and current. An annular beam RKA and a solid beam RKA with almost the same geometric parameters are compared in particle-in-cell simulation. Output microwave power of 100 MW, gain of 50 dB, and power conversion efficiency of 42% are obtained in an annular beam RKA. The annular beam needs a 15% lower uniform guiding magnetic field than the solid beam. Our investigations demonstrate that we are able to use a simple annular explosive cathode immersed in a lower uniform magnetic field instead of a solid thermionic cathode in a complicated partially shielding magnetic field for designing high-impedance RKA, which avoids high temperature requirement, complicated electron-optical system, large area convergence, high current density, and emission uniformity for the solid beam. An equivalent method for the annular beam and the solid beam on bunching features is proposed and agrees with the simulation. The annular beam has the primary advantages over the solid beam that it can employ the immersing uniform magnetic field avoiding the complicated shielding magnetic field system and needs a lower optimum guiding field due to the smaller space charge effect.

  16. New, high-efficiency ion trap mobility detection system for narcotics and explosives

    NASA Astrophysics Data System (ADS)

    McGann, William J.; Bradley, V.; Borsody, A.; Lepine, S.

    1994-10-01

    A new patented Ion Trap Mobility Spectrometer (ITMS) design is presented. Conventional IMS designs typically operate below 0.1% efficiency. This is due primarily to electric field driven, sample ion discharge on a shutter grid. Since 99.9% of the sample ions generated in the reaction region are lost in this discharge process, the sensitivity of conventional systems is limited. The new design provides greater detection efficiency than conventional designs through the use of an `ion trap' concept. The paper describes the plasma and sample ion dynamics in the reaction region of the new detector and discusses the advantages of utilizing a `field-free' space to generate sample ions with high efficiency. Fast electronic switching is described which is used to perturb the field-free space and pulse the sample ions into the drift region for separation and subsequent detection using pseudo real-time software for analysis and display of the data. Many applications for this new detector are now being considered including the detection of narcotics and explosives. Preliminary ion spectra, reduced mobility data and sensitivity data are presented for fifteen narcotics, including cocaine, THC and LSD are reported.

  17. Low amplitude insult project: PBX 9501 high explosive violent reaction experiments

    SciTech Connect

    Idar, D.J.; Lucht, R.A.; Straight, J.W.; Scammon, R.J.; Browning, R.V.; Middleditch, J.; Dienes, J.K.; Skidmore, C.B.; Buntain, G.A.

    1998-12-31

    The Modified Steven test geometry has been used with several different target designs to investigate the mechanical loading behavior of PBX 9501 to a low velocity impact. A 2 kg. mild steel spigot projectile is launched via a new powder driven gun design, from {approximately} 20 to 105 m/s, at lightly confined, steel targets. Brief descriptions of the gun design and operation are given. The threshold velocity to reaction for various target designs, different PBX 9501 lots, and different high explosive (HE) thicknesses are reported and compared. Various diagnostics have been employed to evaluate the pressure profile and timing, and target strain behavior relative to projectile impact. The violence of reaction, as measured by both passive and active techniques, is reported relative to a steady state detonation in PBX 9501. Experimental results suggest slightly different ignition mechanisms dominate based on (HE) thickness, resulting in delayed reactions from {approximately} 0.2- to 2.8-ms after impact. Post-test analyses of the PBX 9501 are briefly summarized.

  18. Photoactive high explosives: linear and nonlinear photochemistry of petrin tetrazine chloride.

    PubMed

    Greenfield, Margo T; McGrane, Shawn D; Bolme, Cindy A; Bjorgaard, Josiah A; Nelson, Tammie R; Tretiak, Sergei; Scharff, R Jason

    2015-05-21

    Pentaerythritol tetranitrate (PETN), a high explosive, initiates with traditional shock and thermal mechanisms. In this study, the tetrazine-substituted derivative of PETN, pentaerythritol trinitrate chlorotetrazine (PetrinTzCl), is being investigated for a photochemical initiation mechanism that could allow control over the chemistry contributing to decomposition leading to initiation. PetrinTzCl exhibits a photochemical quantum yield (QYPC) at 532 nm not evident with PETN. Using static spectroscopic methods, we observe energy absorption on the tetrazine (Tz) ring that results in photodissociation yielding N2, Cl-CN, and Petrin-CN as the major photoproducts. The QYPC was enhanced with increasing irradiation intensity. Experiment and theoretical calculations imply this excitation mechanism follows sequential photon absorption. Dynamic simulations demonstrate that the relaxation mechanism leading to the observed photochemistry in PetrinTzCl is due to vibrational excitation during internal conversion. PetrinTzCl's single photon stability and intensity dependence suggest this material could be stable in ambient lighting, yet possible to initiate with short-pulsed lasers. PMID:25951102

  19. New high-efficiency ion trap mobility detection system for narcotics and explosives

    NASA Astrophysics Data System (ADS)

    McGann, William J.; Jenkins, Anthony; Ribiero, K.; Napoli, J.

    1994-03-01

    A new patented ion trap mobility spectrometer design is presented. Conventional IMS designs typically operate below 0.1% efficiency. This is due primarily to electrical-field-driven, sample ion discharge on a shutter grid. Since 99.9% of the sample ions generated in the reaction region are lost in this discharge process, the sensitivity of conventional systems is limited. The new design provides greater detection efficiency than conventional designs through the use of an `ion trap' concept. The paper describes the plasma and sample ion dynamics in the reaction region of the new detector and discusses the advantages of utilizing a `field-free' space to generate sample ions with high efficiency. Fast electronic switching is described which is used to perturb the field-free space and pulse the sample ions into the drift region for separation and subsequent detection using pseudo real-time software for analysis and display of the data. Many applications for this new detector are now being considered including the detection of narcotics and explosives. Preliminary ion spectra, reduced mobility data and sensitivity data are presented for fifteen narcotics, including cocaine, THC, and LSD are reported.

  20. Characterization of Detonation Soot Produced During Steady and Overdriven Conditions for Three High Explosive Formulations

    NASA Astrophysics Data System (ADS)

    Podlesak, David; Amato, Ronald; Dattelbaum, Dana; Firestone, Millicent; Gustavsen, Richard; Huber, Rachel; Ringstrand, Bryan

    2015-06-01

    The detonation of high explosives (HE) produces a dense fluid of molecular gases and solid carbon. The solid detonation carbon contains various carbon allotropes such as detonation nanodiamonds, ``onion-like'' carbon, graphite and amorphous carbon, with the formation of the different forms dependent upon pressure, temperature and the environmental conditions of the detonation. We have collected solid carbon residues from controlled detonations of three HE formulations (Composition B-3, PBX 9501, and PBX 9502). Soot was collected from experiments designed to produce both steady and overdriven conditions, and from detonations in both an ambient (air) atmosphere and in an inert Ar atmosphere. Structural studies to glean the features of the solid carbon products have been performed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), powder X-ray diffraction (XRD), Raman spectroscopy, small-angle X-ray scattering (SAXS), and X-Ray Pair Distribution Function measurements (PDF). Bulk soot was also analyzed for elemental and isotopic compositions. We will discuss differences in the structure and composition of the detonation carbon as a function of formulation, detonation conditions, and the surrounding atmosphere.

  1. Computational Study of 3-D Hot-Spot Initiation in Shocked Insensitive High-Explosive

    NASA Astrophysics Data System (ADS)

    Najjar, F. M.; Howard, W. M.; Fried, L. E.

    2011-06-01

    High explosive shock sensitivity is controlled by a combination of mechanical response, thermal properties, and chemical properties. The interplay of these physical phenomena in realistic condensed energetic materials is currently lacking. A multiscale computational framework is developed investigating hot spot (void) ignition in a single crystal of an insensitive HE, TATB. Atomistic MD simulations are performed to provide the key chemical reactions and these reaction rates are used in 3-D multiphysics simulations. The multiphysics code, ALE3D, is linked to the chemistry software, Cheetah, and a three-way coupled approach is pursued including hydrodynamics, thermal and chemical analyses. A single spherical air bubble is embedded in the insensitive HE and its collapse due to shock initiation is evolved numerically in time; while the ignition processes due chemical reactions are studied. Our current predictions showcase several interesting features regarding hot spot dynamics including the formation of a ``secondary'' jet. Results obtained with hydro-thermo-chemical processes leading to ignition growth will be discussed for various pore sizes and different shock pressures. LLNL-ABS-471438. This work performed under the auspices of the U.S. Department of Energy by LLNL under Contract DE-AC52-07NA27344.

  2. Dissolution kinetics of high explosives particles in a saturated sandy soil.

    PubMed

    Morley, Matthew C; Yamamoto, Hiroshi; Speitel, Gerald E; Clausen, Jay

    2006-05-30

    Solid phase high explosive (HE) residues from munitions detonation may be a persistent source of soil and groundwater contamination at military training ranges. Saturated soil column tests were conducted to observe the dissolution behavior of individual components (RDX, HMX, and TNT) from two HE formulations (Comp B and C4). HE particles dissolved readily, with higher velocities yielding higher dissolution rates, higher mass transfer coefficients, and lower effluent concentrations. Effluent concentrations were below solubility limits for all components at superficial velocities of 10-50 cm day(-1). Under continuous flow at 50 cm day(-1), RDX dissolution rates from Comp B and C4 were 34.6 and 97.6 microg h(-1) cm(-2) (based on initial RDX surface area), respectively, significantly lower than previously reported dissolution rates. Cycling between flow and no-flow conditions had a small effect on the dissolution rates and effluent concentrations; however, TNT dissolution from Comp B was enhanced under intermittent-flow conditions. A model that includes advection, dispersion, and film transfer resistance was developed to estimate the steady-state effluent concentrations.

  3. Sensitivity effects of void density and arrangements in a REBO high explosive

    SciTech Connect

    Herring, Stuart Davis; Germann, Timothy C; Gronbech - Jensen, Niels

    2010-09-28

    The shock response of two-dimensional model, high explosive crystals with various arrangements of circular voids is explored. We simulate a piston impact using molecular dynamics simulations with a Reactive Empirical Bond Order (REBO) model potential for a sub-micron, sub-ns exothermic reaction in a diatomic molecular solid. In square lattices of voids all of one size, reducing that size or increasing the porosity while holding the other parameter fixed causes the hotspots to consume the material more quickly and detonation to occur sooner and at lower piston velocities. The early time behavior is seen to follow a very simple ignition and growth model. The hotspots are seen to collectively develop a broad pressure wave (a sonic, diffuse deflagration front) that, upon merging with the lead shock, transforms it into a detonation. The reaction yields produced by triangular lattices are not significantly different. With random void arrangements, the mean time to detonation is 15.5% larger than with the square lattice; the standard deviation of detonation delays is just 5.1%.

  4. Critical velocities for deflagration and detonation triggered by voids in a REBO high explosive

    SciTech Connect

    Herring, Stuart Davis; Germann, Timothy C; Jensen, Niels G

    2010-01-01

    The effects of circular voids on the shock sensitivity of a two-dimensional model high explosive crystal are considered. We simulate a piston impact using molecular dynamics simulations with a Reactive Empirical Bond Order (REBO) model potential for a sub-micron, sub-ns exothermic reaction in a diatomic molecular solid. The probability of initiating chemical reactions is found to rise more suddenly with increasing piston velocity for larger voids that collapse more deterministically. A void with radius as small as 10 nm reduces the minimum initiating velocity by a factor of 4. The transition at larger velocities to detonation is studied in a micron-long sample with a single void (and its periodic images). The reaction yield during the shock traversal increases rapidly with velocity, then becomes a prompt, reliable detonation. A void of radius 2.5 nm reduces the critical velocity by 10% from the perfect crystal. A Pop plot of the time-to-detonation at higher velocities shows a characteristic pressure dependence.

  5. Highly sensitive gas-phase explosive detection by luminescent microporous polymer networks

    PubMed Central

    Räupke, André; Palma-Cando, Alex; Shkura, Eugen; Teckhausen, Peter; Polywka, Andreas; Görrn, Patrick; Scherf, Ullrich; Riedl, Thomas

    2016-01-01

    We propose microporous networks (MPNs) of a light emitting spiro-carbazole based polymer (PSpCz) as luminescent sensor for nitro-aromatic compounds. The MPNs used in this study can be easily synthesized on arbitrarily sized/shaped substrates by simple and low-cost electrochemical deposition. The resulting MPN afford an extremely high specific surface area of 1300 m2/g, more than three orders of magnitude higher than that of the thin films of the respective monomer. We demonstrate, that the luminescence of PSpCz is selectively quenched by nitro-aromatic analytes, e.g. nitrobenzene, 2,4-DNT and TNT. In striking contrast to a control sample based on non-porous spiro-carbazole, which does not show any luminescence quenching upon exposure to TNT at levels of 3 ppm and below, the microporous PSpCz shows a clearly detectable response even at TNT concentrations as low as 5 ppb, clearly demonstrating the advantage of microporous films as luminescent sensors for traces of explosive analytes. This level states the vapor pressure of TNT at room temperature. PMID:27373905

  6. Macrokinetics of the Energy Release in High Explosives Containing Nano-Size Boron Particles

    NASA Astrophysics Data System (ADS)

    Utkin, Alexander; Kanel, Gennady; Bogach, Andrey; Razorenov, Sergey

    1999-06-01

    The detonation of high explosives with the metal additives is accompanied with several exothermic and endothermic processes of the energy release and the mechanical and thermal relaxation. In the paper, results of measurements of the pressure and the particle velocity profiles in shock and detonation waves are presented for a pure coarse-grain and a fine-grain HMX and for the fine-grain HMX + 16.4% boron mixture. For these measurements, the manganin pressure gauges and the laser Doppler velocimeter VISAR were applied. Using computer simulations of the phenomena, the equation of state and macrokinetics of the HE decomposition in the shock and detonation waves have been evaluated. Effects of boron in the energy release process were observed both in the detonation and the shock-wave initiation regimes. In general, the boron gives a negative effect on the detonation parameters. It seems, the initial decomposition rate and the detonation parameters in the mixture are controlled by a heat exchange rather than by a chemical interaction between the HE decomposition products and the boron particles. The additional energy of the boron burn in the detonation products is released at later times ranging from 0.1-0.2 mks to 1-2 mks.

  7. Highly sensitive gas-phase explosive detection by luminescent microporous polymer networks

    NASA Astrophysics Data System (ADS)

    Räupke, André; Palma-Cando, Alex; Shkura, Eugen; Teckhausen, Peter; Polywka, Andreas; Görrn, Patrick; Scherf, Ullrich; Riedl, Thomas

    2016-07-01

    We propose microporous networks (MPNs) of a light emitting spiro-carbazole based polymer (PSpCz) as luminescent sensor for nitro-aromatic compounds. The MPNs used in this study can be easily synthesized on arbitrarily sized/shaped substrates by simple and low-cost electrochemical deposition. The resulting MPN afford an extremely high specific surface area of 1300 m2/g, more than three orders of magnitude higher than that of the thin films of the respective monomer. We demonstrate, that the luminescence of PSpCz is selectively quenched by nitro-aromatic analytes, e.g. nitrobenzene, 2,4-DNT and TNT. In striking contrast to a control sample based on non-porous spiro-carbazole, which does not show any luminescence quenching upon exposure to TNT at levels of 3 ppm and below, the microporous PSpCz shows a clearly detectable response even at TNT concentrations as low as 5 ppb, clearly demonstrating the advantage of microporous films as luminescent sensors for traces of explosive analytes. This level states the vapor pressure of TNT at room temperature.

  8. Damage & fracture of high-explosive mock subject to cyclic loading

    SciTech Connect

    Liu, Cheng; Rae, Philip J; Cady, Carl M; Lovato, Manuel L

    2011-01-11

    We use four-point bend specimen with a single shallow edge notch to study the fracture process in Mock 900-21, a PBX 9501 high explosive simulant mock. Subject to monotonic loading we determine quantitatively the threshold load for macroscopic crack initiation from the notch tip. The four-point bend specimen is then subject to cyclic loading in such a way that during the first cycle, the applied force approaches but does not exceed the threshold load determined from the monotonic loading test and in the subsequent cycles, the overall maximum deformation is maintained to be equal to that of the first cycle. It is expected and is also confirmed that no macroscopic damage and cracking occur during the first cycle. However, we observe that sizable macroscopic crack is generated and enlarged during the subsequent cycles, even though the applied force never exceeds the threshold load. Details of the process of damage fonnation, accumulation, and crack extension are presented and the mechanical mechanism responsible for such failure process is postulated and discussed.

  9. Highly sensitive gas-phase explosive detection by luminescent microporous polymer networks.

    PubMed

    Räupke, André; Palma-Cando, Alex; Shkura, Eugen; Teckhausen, Peter; Polywka, Andreas; Görrn, Patrick; Scherf, Ullrich; Riedl, Thomas

    2016-01-01

    We propose microporous networks (MPNs) of a light emitting spiro-carbazole based polymer (PSpCz) as luminescent sensor for nitro-aromatic compounds. The MPNs used in this study can be easily synthesized on arbitrarily sized/shaped substrates by simple and low-cost electrochemical deposition. The resulting MPN afford an extremely high specific surface area of 1300 m(2)/g, more than three orders of magnitude higher than that of the thin films of the respective monomer. We demonstrate, that the luminescence of PSpCz is selectively quenched by nitro-aromatic analytes, e.g. nitrobenzene, 2,4-DNT and TNT. In striking contrast to a control sample based on non-porous spiro-carbazole, which does not show any luminescence quenching upon exposure to TNT at levels of 3 ppm and below, the microporous PSpCz shows a clearly detectable response even at TNT concentrations as low as 5 ppb, clearly demonstrating the advantage of microporous films as luminescent sensors for traces of explosive analytes. This level states the vapor pressure of TNT at room temperature. PMID:27373905

  10. Tailoring wet explosion process parameters for the pretreatment of cocksfoot grass for high sugar yields.

    PubMed

    Njoku, S I; Ahring, B K; Uellendahl, H

    2013-08-01

    The pretreatment of lignocellulosic biomass is crucial for efficient subsequent enzymatic hydrolysis and ethanol fermentation. In this study, wet explosion (WEx) pretreatment was applied to cocksfoot grass and pretreatment conditions were tailored for maximizing the sugar yields using response surface methodology. The WEx process parameters studied were temperature (160-210 °C), retention time (5-20 min), and dilute sulfuric acid concentration (0.2-0.5 %). The pretreatment parameter set E, applying 210 °C for 5 min and 0.5 % dilute sulfuric acid, was found most suitable for achieving a high glucose release with low formation of by-products. Under these conditions, the cellulose and hemicellulose sugar recovery was 94 % and 70 %, respectively. The efficiency of the enzymatic hydrolysis of cellulose under these conditions was 91 %. On the other hand, the release of pentose sugars was higher when applying less severe pretreatment conditions C (160 °C, 5 min, 0.2 % dilute sulfuric acid). Therefore, the choice of the most suitable pretreatment conditions is depending on the main target product, i.e., hexose or pentose sugars.

  11. Solid-state modeling of the terahertz spectrum of the high explosive HMX.

    PubMed

    Allis, Damian G; Prokhorova, Darya A; Korter, Timothy M

    2006-02-01

    The experimental solid-state terahertz (THz) spectrum (3-120 cm(-1)) of the beta-crystal form of the high explosive octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) has been analyzed using solid-state density functional theory calculations. Various density functionals (both generalized gradient approximation and local density approximation) are compared in terms of their abilities to reproduce the experimentally observed solid-state structure and low-frequency vibrational motions. Good-to-excellent agreement between solid-state theory and experiment can be achieved in the THz region where isolated-molecule calculations fail to reproduce the observed spectral features, demonstrating a clear limitation of using isolated-molecule calculations for the assignment of THz frequency motions in molecular solids. The deficiency of isolated-molecule calculations is traced to modification of the molecular structure in the solid state through crystal packing effects and the formation of weak C-H...O hydrogen bonds.

  12. Performance evaluation of diaminoazoxyfurazan (DAAF) as a booster material for insensitive high explosives using the onionskin test

    SciTech Connect

    Morris, John S; Francois, Elizabeth G; Hooks, Daniel E; Hill, Larry G; Harry, Herbert H

    2010-11-09

    Initiation of insensitive high explosive (IHE) formulations requires the use of a booster explosive in the initiation train. Booster material selection is crucial, as the initiation must reliably function across some spectrum of physical parameters. The interest in DAAF for this application stems from the fact that it possesses many traits of an IHE but is shock sensitive enough to serve as an explosive booster. A hemispherical wave breakout test, termed the onionskin test, is one of the methods used to evaluate the performance of a booster material. The wave breakout time-position history at the surface of a hemisphericallHE charge is recorded and the relative uniformity of the breakout can be quantitatively compared between booster materials. A series of onionskin tests were performed to investigate breakout and propagation diaminoazoxyfurazan (DAAF) at low temperatures to evaluate ignition and detonation spreading in comparison to other explosives commonly used in booster applications. Some wave perturbation was observed with the DAAF booster in the onionskin tests presented. The results of these tests will be presented and discussed.

  13. Reduction of Hazardous Waste from High School Chemistry Laboratories.

    ERIC Educational Resources Information Center

    Wahl, George H., Jr., Ed.

    This document provides teachers with sources of useful information and new ideas about the high school chemistry laboratory program. Chapters included are: (1) "Introduction" describing the philosophy and specific objectives of this project; (2) "Importance of Laboratory Work"; (3) "Chemistry Lab Outline" listing titles of experiments in four…

  14. Science Laboratory Classroom Environments in Korean High Schools

    ERIC Educational Resources Information Center

    Fraser, Barry J.; Lee, Sunny S. U.

    2009-01-01

    In order to investigate the learning environment of senior high school science laboratory classrooms in Korea, the Science Laboratory Environment Inventory (SLEI) was translated into Korean and administered to 439 students (99 science-independent stream students, 195 science-oriented stream students and 145 humanities stream students). Data…

  15. Uses of Fabry-Perot velocimeters in studies of high explosives detonation

    SciTech Connect

    Breithaupt, R.D.; Tarver, C.M.

    1990-08-27

    The Fabry Perot has become an important and valuable tool by which explosive performance information can be obtained relatively easily and inexpensively. Principle uses of the Fabry Perot have been free surface, and particle velocity measurements in one dimensional studies of explosive performance. In the cylinder test, it has been very useful to resolve early wall motions. We have refined methods of characterizing new explosives i.e. equation of state, C-J pressure, via the cylinder shot, flat plate, and particle velocity techniques. All of these use Fabry Perot as one of the principle diagnostics. Each of these experimental techniques are discussed briefly and some of the results obtained. Modeling developed to fit Fabry-Perot results are described along with future testing.

  16. Explosively pumped laser light

    DOEpatents

    Piltch, Martin S.; Michelotti, Roy A.

    1991-01-01

    A single shot laser pumped by detonation of an explosive in a shell casing. The shock wave from detonation of the explosive causes a rare gas to luminesce. The high intensity light from the gas enters a lasing medium, which thereafter outputs a pulse of laser light to disable optical sensors and personnel.

  17. Explosives simulants: Preliminary report

    SciTech Connect

    Moody, G.L.; Pruneda, C.O.; Simpson, R.L.

    1992-03-04

    Two TNT high explosives simulants have been developed. Small scale testing has shown them to be insensitive to: impact, spark, friction, temperature, and shock. The materials have been scaled to 0.5 kg quantities and samples given to the Protective Services Department for field evaluation using explosives detecting canines.

  18. New developments of the CARTE thermochemical code: Calculation of detonation properties of high explosives

    NASA Astrophysics Data System (ADS)

    Dubois, Vincent; Desbiens, Nicolas; Auroux, Eric

    2010-07-01

    We present the improvements of the CARTE thermochemical code which provides thermodynamic properties and chemical compositions of CHON systems over a large range of temperature and pressure with a very small computational cost. The detonation products are split in one or two fluid phase (s), treated with the MCRSR equation of state (EOS), and one condensed phase of carbon, modeled with a multiphase EOS which evolves with the chemical composition of the explosives. We have developed a new optimization procedure to obtain an accurate multicomponents EOS. We show here that the results of CARTE code are in good agreement with the specific data of molecular systems and measured detonation properties for several explosives.

  19. Determining explosivity part II: comparison of small-scale cartridge tests to actual pipe bombs.

    PubMed

    Oxley, J C; Smith, J L; Resende, E

    2001-09-01

    The small-scale explosivity device (SSED) has been used to assess the explosive power of a number of low explosives-smokeless powders (WC-870, Red Dot, Bullseye, Winchester Action Pistol, and IMR-PB), Pyrodex, black powder, and an improvised explosive (TATP). The device requires 2 g of energetic material, a heavy-walled containment vessel, and a standard blast shield to permit use in most laboratories. The data from the SSED are compared with the fragmentation of pipe bombs which contained 300 to 700 g of powder. The SSED provided the same relative ordering of explosivity as suggested by the fragmentation of the real devices. In addition, the SSED was used to evaluate the chemical residue remaining after an explosion. Issues in using the device such as optimal detonators and restricted reaction volume were probed using three high explosives--TNT, Tetryl, and RDX. PMID:11569544

  20. High energy physics at Brookhaven National Laboratory

    SciTech Connect

    Samios, N.P.

    1982-01-01

    The high energy plans at BNL are centered around the AGS and ISABELLE, or a variant thereof. At present the AGS is maintaining a strong and varied program. This last year a total of 4 x 10/sup 19/ protons were delivered on target in a period of approximately 20 weeks. Physics interest is very strong, half of the submitted proposals are rejected (thereby maintaining high quality experiments) and the program is full over the next two years. The future colliding beam facility will utilize the AGS as an injector and will be a dedicated facility. It will have six intersection regions, run > 10/sup 7/ sec/year, and explore a new domain of energy and luminosity. Common to all the considered alternatives is a large aperture proton ring. These possible choices involve pp, ep, and heavy ion variants. The long term philosophy is to run the AGS as much as possible, continuously to upgrade it in performance and reliability, and then to phase it down as the new collider begins operation. (WHK)

  1. Reliable discrimination of high explosive and chemical/biological artillery using acoustic UGS

    NASA Astrophysics Data System (ADS)

    Hohil, Myron E.; Desai, Sachi

    2005-10-01

    discrimination between conventional and simulated chemical/biological artillery rounds using acoustic signals produced during detonation. Distinct characteristics arise within the different airburst signatures because high explosive warheads emphasize concussive and shrapnel effects, while chemical/biological warheads are designed to disperse their contents over large areas, therefore employing a slower burning, less intense explosive to mix and spread their contents. The ensuing blast waves are readily characterized by variations in the corresponding peak pressure and rise time of the blast, differences in the ratio of positive pressure amplitude to the negative amplitude, and variations in the overall duration of the resulting waveform. We show that, highly reliable discrimination (> 98%) between conventional and potentially chemical/biological artillery is achieved at ranges exceeding 3km. A feedforward neural network classifier, trained on a feature space derived from the distribution of wavelet coefficients found within different levels of the multiresolution decomposition yields.

  2. The Off-Site Plowshare and Vela Uniform Programs: Assessing Potential Environmental Liabilities through an Examination of Proposed Nuclear Projects,High Explosive Experiments, and High Explosive Construction Activities Volume 3 of 3

    SciTech Connect

    Beck Colleen M.,Edwards Susan R.,King Maureen L.

    2011-09-01

    This document presents the results of nearly six years (2002-2008) of historical research and field studies concerned with evaluating potential environmental liabilities associated with U.S. Atomic Energy Commission projects from the Plowshare and Vela Uniform Programs. The Plowshare Program's primary purpose was to develop peaceful uses for nuclear explosives. The Vela Uniform Program focused on improving the capability of detecting, monitoring and identifying underground nuclear detonations. As a result of the Project Chariot site restoration efforts in the early 1990s, there were concerns that there might be other project locations with potential environmental liabilities. The Desert Research Institute conducted archival research to identify projects, an analysis of project field activities, and completed field studies at locations where substantial fieldwork had been undertaken for the projects. Although the Plowshare and Vela Uniform nuclear projects are well known, the projects that are included in this research are relatively unknown. They are proposed nuclear projects that were not executed, proposed and executed high explosive experiments, and proposed and executed high explosive construction activities off the Nevada Test Site. The research identified 170 Plowshare and Vela Uniform off-site projects and many of these had little or no field activity associated with them. However, there were 27 projects that merited further investigation and field studies were conducted at 15 locations.

  3. The Off-Site Plowshare and Vela Uniform Programs: Assessing Potential Environmental Liabilities through an Examination of Proposed Nuclear Projects,High Explosive Experiments, and High Explosive Construction Activities Volume 2 of 3

    SciTech Connect

    Beck Colleen M.,Edwards Susan R.,King Maureen L.

    2011-09-01

    This document presents the results of nearly six years (2002-2008) of historical research and field studies concerned with evaluating potential environmental liabilities associated with U.S. Atomic Energy Commission projects from the Plowshare and Vela Uniform Programs. The Plowshare Program's primary purpose was to develop peaceful uses for nuclear explosives. The Vela Uniform Program focused on improving the capability of detecting, monitoring and identifying underground nuclear detonations. As a result of the Project Chariot site restoration efforts in the early 1990s, there were concerns that there might be other project locations with potential environmental liabilities. The Desert Research Institute conducted archival research to identify projects, an analysis of project field activities, and completed field studies at locations where substantial fieldwork had been undertaken for the projects. Although the Plowshare and Vela Uniform nuclear projects are well known, the projects that are included in this research are relatively unknown. They are proposed nuclear projects that were not executed, proposed and executed high explosive experiments, and proposed and executed high explosive construction activities off the Nevada Test Site. The research identified 170 Plowshare and Vela Uniform off-site projects and many of these had little or no field activity associated with them. However, there were 27 projects that merited further investigation and field studies were conducted at 15 locations.

  4. The Off-Site Plowshare and Vela Uniform Programs: Assessing Potential Environmental Liabilities through an Examination of Proposed Nuclear Projects,High Explosive Experiments, and High Explosive Construction Activities Volume 1 of 3

    SciTech Connect

    Beck Colleen M,Edwards Susan R.,King Maureen L.

    2011-09-01

    This document presents the results of nearly six years (2002-2008) of historical research and field studies concerned with evaluating potential environmental liabilities associated with U.S. Atomic Energy Commission projects from the Plowshare and Vela Uniform Programs. The Plowshare Program's primary purpose was to develop peaceful uses for nuclear explosives. The Vela Uniform Program focused on improving the capability of detecting, monitoring and identifying underground nuclear detonations. As a result of the Project Chariot site restoration efforts in the early 1990s, there were concerns that there might be other project locations with potential environmental liabilities. The Desert Research Institute conducted archival research to identify projects, an analysis of project field activities, and completed field studies at locations where substantial fieldwork had been undertaken for the projects. Although the Plowshare and Vela Uniform nuclear projects are well known, the projects that are included in this research are relatively unknown. They are proposed nuclear projects that were not executed, proposed and executed high explosive experiments, and proposed and executed high explosive construction activities off the Nevada Test Site. The research identified 170 Plowshare and Vela Uniform off-site projects and many of these had little or no field activity associated with them. However, there were 27 projects that merited further investigation and field studies were conducted at 15 locations.

  5. PBX 9501 high explosive violent response/low amplitude insult project: Phase I

    SciTech Connect

    Idar, D.J.; Lucht, R.A.; Scammon, R.; Straight, J.; Skidmore, C.B.

    1997-01-01

    Preliminary modeling and experimental analyses of the violent reaction threshold of semi-heavily confined PBX 9501 to low velocity impact have been completed. Experimental threshold measurements were obtained with ten tests using a spigot gun design to launch a hemispherical projectile at the high explosive contained in stainless steel. Powder curves were determined for several gun barrel designs, powders, and projectile materials and have proven to be very reproducible over the range of 75 to 325 ft/s. A threshold velocity of approximately 246 ft/s for violent reaction of the PBX 9501 was determined with experimental gauge and switch measurements and the remaining physical test evidence. Preliminary analyses of the PBX 9501 samples retrieved from both unreacted and partially reacted targets have been completed. Core samples were obtained from the unreacted targets and submitted for density determinations. The subsequent analysis supports the concept that the PBX 9501 yields and fractures under the low velocity compression event to expand and fill the annular gap in the target design. Samples of PBX 9501 from the partially reacted targets were examined with scanning electron microscope and light microscope techniques. Increased evidence of mechanical twinning effects are noted in the HMX crystals from the partially reacted targets. Finite element calculations using DYNA213, with a modified ORION post processor, without reaction or chemistry models, were used to support the design of targets, to compare predictive analyses with experimental measurements, and to evaluate a proposed ignition criterion in a power law form for threshold to reaction with dependence on pressure, maximum shear strain rate, and time variables. The calculations show good agreement with the physical dent and deformation data from the remaining target evidence; however, they do not match the experimental pressure gauge measurements well.

  6. Chemical and biological systems for regenerating activated carbon contaminated with high explosives

    SciTech Connect

    Knezovich, J.P.; Daniels, J.I.; Stenstrom, M.K.; Heilmann, H.M.

    1994-12-01

    Activated carbon has been used as a substrate for efficiently removing high explosives (HEs) from aqueous and gaseous waste streams. Carbon that is saturated with HEs, however, constitutes a solid waste and is currently being stored because appropriate technologies for its treatment are not available. Because conventional treatment strategies (i.e., incineration, open burning) are not safe or will not be in compliance with future regulations, new and cost-effective methods are required for the elimination of this solid waste. Furthermore, because the purchase of activated carbon and its disposal after loading with HEs will be expensive, an ideal treatment method would result in the regeneration of the carbon thereby permitting its reuse. Coupling chemical and biological treatment systems, such as those described below, will effectively meet these technical requirements. The successful completion of this project will result in the creation of engineered commercial systems that will present safe and efficient methods for reducing the quantities of HE-laden activated carbon wastes that are currently in storage or are generated as a result of demilitarization activities. Biological treatment of hazardous wastes is desirable because the biodegradation process ultimately leads to the mineralization (e.g., conversion to carbon dioxide, nitrogen gas, and water) of parent compounds and has favorable public acceptance. These methods will also be cost- effective because they will not require large expenditures of energy and will permit the reuse of the activated carbon. Accordingly, this technology will have broad applications in the private sector and will be a prime candidate for technology transfer.

  7. A model for shear-band formation and high-explosive initiation in a hydrodynamics code

    SciTech Connect

    Kerrisk, J.F.

    1996-03-01

    This report describes work in progress to develop a shear band model for MESA-2D. The object of this work is (1) to predict the formation of shear bands and their temperature in high explosive (HE) during a MESA-2D calculation, (2) to then assess whether the HE would initiate, and (3) to allow a detonation wave initiated from a shear band to propagate. This requires developing a model that uses average cell data to estimate the size and temperature of narrow region (generally much narrower than the cell size) that is undergoing shear within the cell. The shear band temperature (rather than the average cell temperature) can be used to calculate the flow stress of the material in the cell or to calculate heat generation from reactive materials. Modifications have been made to MESA-2D to calculate shear band size and temperature, and to initiate HE detonation when conditions warrant. Two models have been used for shear-band size and temperature calculation, one based on an independent estimate of the shear band width and a second based on the temperature distribution around the shear band. Both models have been tested for calculations in which shear band formation occurs in steel. A comparison of the measured and calculated local temperature rise in a shear band has been made. A model for estimating the time to initiation of the HE based on the type of HE and the temperature distribution in a shear band has also been added to MESA-2D. Calculations of conditions needed to initiate HE in projectile-impact tests have been done and compared with experimental data. Further work is d to test the model.

  8. High-temperature superconductor applications development at Argonne National Laboratory

    SciTech Connect

    Hull, J.R.; Poeppel, R.B.

    1992-02-09

    Developments at Argonne National Laboratory of near and intermediate term applications using high-temperature superconductors are discussed. Near-term applications of liquid-nitrogen depth sensors, current leads, and magnetic bearings are discussed in detail.

  9. Molecular design and property prediction of high density polynitro[3.3.3]-propellane-derivatized frameworks as potential high explosives.

    PubMed

    Zhang, Qinghua; Zhang, Jiaheng; Qi, Xiujuan; Shreeve, Jean'ne M

    2014-11-13

    Research in energetic materials is now heavily focused on the design and synthesis of novel insensitive high explosives (IHEs) for specialized applications. As an effective and time-saving tool for screening potential explosive structures, computer simulation has been widely used for the prediction of detonation properties of energetic molecules with relatively high precision. In this work, a series of new polynitrotetraoxopentaaza[3.3.3]-propellane molecules with tricyclic structures were designed. Their properties as potential high explosives including density, heats of formation, detonation properties, impact sensitivity, etc., have been extensively evaluated using volume-based thermodynamic calculations and density functional theory (DFT).These new energetic molecules exhibit high densities of >1.82 g cm(-3), in which 1 gives the highest density of 2.04 g cm(-3). Moreover, most new materials show good detonation properties and acceptable impact sensitivities, in which 5 displays much higher detonation velocity (9482 m s(-1)) and pressure (43.9 GPa) than HMX and has a h50 value of 11 cm. These results are expected to facilitate the experimental synthesis of new-generation nitramine-based high explosives.

  10. Idaho Explosives Detection System

    SciTech Connect

    Edward L. Reber; J. Keith Jewell; Larry G. Blackwood; Andrew J. Edwards; Kenneth W. Rohde; Edward H. Seabury

    2004-10-01

    The Idaho Explosives Detection System (IEDS) was developed at the Idaho National Laboratory (INL) to respond to threats imposed by delivery trucks carrying explosives into military bases. A full-scale prototype system has been built and is currently undergoing testing. The system consists of two racks, one on each side of a subject vehicle. Each rack includes a neutron generator and an array of NaI detectors. The two neutron generators are pulsed and synchronized. A laptop computer controls the entire system. The control software is easily operable by minimally trained staff. The system was developed to detect explosives in a medium size truck within a 5-minute measurement time. System performance was successfully demonstrated with explosives at the INL in June 2004 and at Andrews Air Force Base in July 2004.

  11. New Mix Explosives for Explosive Welding

    NASA Astrophysics Data System (ADS)

    Andreevskikh, Leonid

    2011-06-01

    Suggested and tested were some mix explosives--powder mixtures of a brisant high explosive (HE = RDX, PETN) and an inert diluent (baking soda)--for use in explosive welding. RDX and PETN were selected in view of their high throwing ability and low critical diameter. Since the decomposition of baking soda yields a huge amount of gaseous products, its presence ensures (even at a low HE percentage) a throwing speed that is sufficient for realization of explosive welding, at a reduced brisant action of charge. Mix chargers containing 30-70 wt % HE (the rest baking soda) have been tested experimentally and optimized. For study of possibility to reduce critical diameter of HE mixture, the mixture was prepared where HE crystal sizes did not exceed 10 μm. The tests, which were performed with this HE, revealed that the mixture detonated stably with the velocity D ~ 2 km/s, if the layer thickness was d = 2 mm. The above explosives afford to markedly diminish deformations within the oblique impact zone and thus to carry out explosive welding of hollow items and thin metallic foils.

  12. Hand held explosives detection system

    DOEpatents

    Conrad, Frank J.

    1992-01-01

    The present invention is directed to a sensitive hand-held explosives detection device capable of detecting the presence of extremely low quantities of high explosives molecules, and which is applicable to sampling vapors from personnel, baggage, cargo, etc., as part of an explosives detection system.

  13. Computer systems for laboratory networks and high-performance NMR.

    PubMed

    Levy, G C; Begemann, J H

    1985-08-01

    Modern computer technology is significantly enhancing the associated tasks of spectroscopic data acquisition and data reduction and analysis. Distributed data processing techniques, particularly laboratory computer networking, are rapidly changing the scientist's ability to optimize results from complex experiments. Optimization of nuclear magnetic resonance spectroscopy (NMR) and magnetic resonance imaging (MRI) experimental results requires use of powerful, large-memory (virtual memory preferred) computers with integrated (and supported) high-speed links to magnetic resonance instrumentation. Laboratory architectures with larger computers, in order to extend data reduction capabilities, have facilitated the transition to NMR laboratory computer networking. Examples of a polymer microstructure analysis and in vivo 31P metabolic analysis are given. This paper also discusses laboratory data processing trends anticipated over the next 5-10 years. Full networking of NMR laboratories is just now becoming a reality. PMID:3840171

  14. Laboratory design for high-performance electron microscopy

    SciTech Connect

    O'Keefe, Michael A.; Turner, John H.; Hetherington, Crispin J.D.; Cullis, A.G.; Carragher, Bridget; Jenkins, Ron; Milgrim, Julie; Milligan,Ronald A.; Potter, Clinton S.; Allard, Lawrence F.; Blom, Douglas A.; Degenhardt, Lynn; Sides, William H.

    2004-04-23

    Proliferation of electron microscopes with field emission guns, imaging filters and hardware spherical aberration correctors (giving higher spatial and energy resolution) has resulted in the need to construct special laboratories. As resolutions improve, transmission electron microscopes (TEMs) and scanning transmission electron microscopes (STEMs) become more sensitive to ambient conditions. State-of-the-art electron microscopes require state-of-the-art environments, and this means careful design and implementation of microscope sites, from the microscope room to the building that surrounds it. Laboratories have been constructed to house high-sensitive instruments with resolutions ranging down to sub-Angstrom levels; we present the various design philosophies used for some of these laboratories and our experiences with them. Four facilities are described: the National Center for Electron Microscopy OAM Laboratory at LBNL; the FEGTEM Facility at the University of Sheffield; the Center for Integrative Molecular Biosciences at TSRI; and the Advanced Microscopy Laboratory at ORNL.

  15. High-dose secondary calibration laboratory accreditation program

    SciTech Connect

    Humphreys, J.C.

    1993-12-31

    There is a need for high-dose secondary calibration laboratories to serve the multi-billion dollar radiation processing industry. This need is driven by the desires of industry for less costly calibrations and faster calibration-cycle response time. Services needed include calibration irradiations of routine processing dosimeters and the supply of reference standard transfer dosimeters for irradiation in the production processing facility. In order to provide measurement quality assurance and to demonstrate consistency with national standards, the high-dose secondary laboratories would be accredited by means of an expansion of an existing National Voluntary Laboratory Accreditation Program. A laboratory performance criteria document is under development to implement the new program.

  16. The Grenoble High Magnetic Field Laboratory as a user facility

    NASA Astrophysics Data System (ADS)

    Debray, F.; Jongbloets, H.; Joss, W.; Martinez, G.; Mossang, E.; Picoche, J. C.; Plante, A.; Rub, P.; Sala, P.; Wyder, P.

    2001-01-01

    The Grenoble High Magnetic Field Laboratory (GHMFL), run jointly by the Centre National de la Recherche Scientifique (CNRS, France) and the Max-Planck Gesellschaft (MPG, Germany) is a leading laboratory pursuing research in the highest static magnetic fields technically feasible. The laboratory maintains strong in-house research activities and partly operates as a user facility for qualified external researchers. It has developed highly sophisticated instrumentation for specific use under high magnetic fields, including transport, magnetization, visible and infrared optical measurements at low temperatures and/or high pressures, EPR and NMR investigations in high magnetic fields. The laboratory delivers around 5000 h of magnet time per year. Access for users to the high magnetic field facility is supported by the European Union, in the framework of the Human Potential Program : “Transnational Access to Major Research Infrastructures”.We give an overview of the technical aspects of the facility and of the laboratory activities as a facility over the last few years. The general organization of the user community and repartition between countries will also be reviewed.

  17. Instabilities and soot formation in high-pressure, rich, iso-octane-air explosion flames. 1. Dynamical structure

    SciTech Connect

    Lockett, R.D.; Woolley, R.

    2007-12-15

    Simultaneous OH planar laser-induced fluorescence (PLIF) and Rayleigh scattering measurements have been performed on 2-bar rich iso-octane-air explosion flames obtained in the optically accessible Leeds combustion bomb. Separate shadowgraph high-speed video images have been obtained from explosion flames under similar mixture conditions. Shadowgraph images, quantitative Rayleigh images, and normalized OH concentration images have been presented for a selection of these explosion flames. Normalized experimental equilibrium OH concentrations behind the flame fronts have been compared with normalized computed equilibrium OH concentrations as a function of equivalence ratio. The ratio of superequilibrium OH concentration in the flame front to equilibrium OH concentration behind the flame front reveals the response of the flame to the thermal-diffusive instability and the resistance of the flame front to rich quenching. Burned gas temperatures have been determined from the Rayleigh scattering images in the range 1.4{<=}{phi}{<=}1.9 and are found to be in good agreement with the corresponding predicted adiabatic flame temperatures. Soot formation was observed to occur behind deep cusps associated with large-wavelength cracks occurring in the flame front for equivalence ratio {phi}{>=}1.8 (C/O{>=}0.576). The reaction time-scale for iso-octane pyrolysis to soot formation has been estimated to be approximately 7.5-10 ms. (author)

  18. Cyclic Explosivity in High Elevation Phreatomagmatic Eruptions at Ocean Island Volcanoes: Implications for Aquifer Pressurization and Volcano Flank Destabilization.

    NASA Astrophysics Data System (ADS)

    Tarff, R.; Day, S. J.; Downes, H.; Seghedi, I.

    2015-12-01

    Groundwater heating and pressurization of aquifers trapped between dikes in ocean island volcanoes has been proposed as a mechanism for destabilizing and triggering large-volume flank collapses. Previous modelling has indicated that heat transfer from sustained magma flow through dikes during eruption has the potential to produce destabilizing levels of pressure on time scales of 4 to 400 days, if the aquifers remain confined. Here we revisit this proposal from a different perspective. We examine evidence for pressure variations in dike-confined aquifers during eruptions at high elevation vents on ocean island volcanoes. Initially magmatic, these eruptions change to mostly small-volume explosive phreatomagmatic activity. A recent example is the 1949 eruption on La Palma, Canary Islands. Some such eruptions involve sequences of larger-volume explosive phases or cycles, including production of voluminous low-temperature, pyroclastic density currents (PDC). Here we present and interpret data from the Cova de Paul crater eruption (Santo Antao, Cape Verde Islands). The phreatomagmatic part of this eruption formed two cycles, each culminating with eruption of PDCs. Compositional and textural variations in the products of both cycles indicate that the diatreme fill began as coarse-grained and permeable which allowed gas to escape. During the eruption, the fill evolved to a finer grained, poorly sorted, less permeable material, in which pore fluid pressures built up to produce violent explosive phases. This implies that aquifers adjacent to the feeder intrusion were not simply depressurized at the onset of phreatomagmatic explosivity but experienced fluctuations in pressure throughout the eruption as the vent repeatedly choked and emptied. In combination with fluctuations in magma supply rate, driving of aquifer pressurization by cyclical vent choking will further complicate the prediction of flank destabilization during comparable eruptions on ocean island volcanoes.

  19. VA02 series of high voltage explosion-proof asynchronous motors

    NASA Astrophysics Data System (ADS)

    Goryagin, V. F.; Zbarskiy, L. A.; Shirnin, I. G.; Porshnev, Yu. V.; Figotina, M. I.

    1987-04-01

    The VAO2 asynchronous, squirrel cage, explosion-proof electric motors have the same power and r.p.m. range, the same weather, water and dust proofing as the predecessor VAO series and are designed for the same explosion hazards. The nominal r.p.m. ranges from 750 to 3,000, the power ratings from 200 to 1,000 kW, voltage ratings are 6,000 and 10,000 volts with efficiencies running from 93.4 to 95.6% and weights of 1,620 to 5,700 kg. The new VAO2 motors incorporate the following improvements: the use of cold rolled electrical steel with lower specific losses; the use of a bottle configuration for the rotor slot instead of the usual oval; an improved exterior cooling system; and a reduction in the average insulation thickness.

  20. Description and validation of ERAD: An atmospheric dispersion model for high explosive detonations

    SciTech Connect

    Boughton, B.A.; DeLaurentis, J.M.

    1992-10-01

    The Explosive Release Atmospheric Dispersion (ERAD) model is a three-dimensional numerical simulation of turbulent atmospheric transport and diffusion. An integral plume rise technique is used to provide a description of the physical and thermodynamic properties of the cloud of warm gases formed when the explosive detonates. Particle dispersion is treated as a stochastic process which is simulated using a discrete time Lagrangian Monte Carlo method. The stochastic process approach permits a more fundamental treatment of buoyancy effects, calm winds and spatial variations in meteorological conditions. Computational requirements of the three-dimensional simulation are substantially reduced by using a conceptualization in which each Monte Carlo particle represents a small puff that spreads according to a Gaussian law in the horizontal directions. ERAD was evaluated against dosage and deposition measurements obtained during Operation Roller Coaster. The predicted contour areas average within about 50% of the observations. The validation results confirm the model`s representation of the physical processes.

  1. Experimental Method to Determine the Detonation Characteristics of a Very Non-Ideal High Explosive

    NASA Astrophysics Data System (ADS)

    Baudin, G.; Le Gallic, C.; Davoine, F.; Bouinot, P.

    2006-07-01

    Common experimental configurations used to determine HE detonation velocity-curvature are right circular cylinders detonated in air. The steadily propagating detonation front is curved and its velocity depends upon the diameter of the cylinder. This configuration requires several experiments with different diameters and sufficiently long cylinders to assume a steadily propagating detonation front. This last hypothesis is practically not achieved for non-ideal HE using reasonably long cylinders. To elude this problem, a special explosive device called "logosphere", developed by CEA, has been adapted to non ideal HE. It provides a well define spherically diverging detonation wave and allows measurements of the detonation velocity-curvature relationship by means of piezoelectric pins without any perturbation. VISAR and IDL diagnostics record the material velocities at the rear surface of the explosive through transparent windows. The particle velocity values are used to determine the curved detonation states using the detonation velocity-acceleration-curvature model of Louis Brun.

  2. Modeling the viscoelastic and brittle fracture response of a high explosive in an Eulerian hydrocode

    SciTech Connect

    Clancy, S.P.; Johnson, J.N.; Burkett, M.W.

    1998-12-31

    A constitutive model that incorporates brittle-fracture-mechanics and viscoelastic material response for PBX-9501 has been developed and implemented in the two-dimensional hydrocode MESA. The hydrocode with the visco-cracking model has been applied to numerous low-rate deformation and low-speed impact events. Several low-speed impact experiments that have quantified the deformation to the explosive have been used to assess the hydrocode and model for this type of material response problem. Comparisons between MESA w/visco-cracking model calculations and experimentally measured mechanical deformation to the explosive showed that reasonable agreement was achieved for the measured magnitude of deformation but the deformation profiles/shapes were found to be different.

  3. Exploring the Physical, Chemical and Thermal Characteristics of a New Potentially Insensitive High Explosive: RX-55-AE-5

    SciTech Connect

    Weese, R K; Burnham, A K; Turner, H C; Tran, T D

    2006-06-05

    Current work at the Energetic Materials Center, EMC, at Lawrence Livermore National Laboratory (LLNL) includes both understanding properties of old explosives and measuring properties of new ones [1]. The necessity to know and understand the properties of energetic materials is driven by the need to improve performance and enhance stability to various stimuli, such as thermal, friction and impact insult. This review will concentrate on the physical properties of RX-55-AE-5, which is formulated from heterocyclic explosive, 2,6-diamino-3,5-dinitropyrazine-1-oxide, LLM-105, and 2.5% Viton A. Differential scanning calorimetry (DSC) was used to measure a specific heat capacity, C{sub p}, of {approx} 0.950 J/g{center_dot} C and a thermal conductivity, {kappa}, of {approx} 0.475 W/m{center_dot} C. The LLNL kinetics modeling code Kinetics05 and the Advanced Kinetics and Technology Solutions (AKTS) code Thermokinetics were both used to calculate Arrhenius kinetics for decomposition of LLM-105. Both obtained an activation energy barrier E {approx} 180 kJ mol{sup -1} for mass loss in an open pan. Thermal mechanical analysis, TMA, was used to measure the coefficient of thermal expansion (CTE). The CTE for this formulation was calculated to be {approx} 61 {micro}m/m{center_dot} C. Impact, spark, friction are also reported.

  4. What High School Students Learn during Internships in Biology Laboratories

    ERIC Educational Resources Information Center

    Roth, Wolff-Michael; van Eijck, Michiel; Hsu, Pei-Ling; Marshall, Anne; Mazumder, Asit

    2009-01-01

    This article reports on the results of the authors' research and development work that was designed to study the impact of internships in scientific laboratories on high school students. The authors sketch how the internships affected cognitive outcomes, experiences and attitudes, and the career aspirations of the high school students. The…

  5. Los Alamos Explosives Performance Key to Stockpile Stewardship

    SciTech Connect

    Dattelbaum, Dana

    2014-11-03

    As the U.S. Nuclear Deterrent ages, one essential factor in making sure that the weapons will continue to perform as designed is understanding the fundamental properties of the high explosives that are part of a nuclear weapons system. As nuclear weapons go through life extension programs, some changes may be advantageous, particularly through the addition of what are known as "insensitive" high explosives that are much less likely to accidentally detonate than the already very safe "conventional" high explosives that are used in most weapons. At Los Alamos National Laboratory explosives research includes a wide variety of both large- and small-scale experiments that include small contained detonations, gas and powder gun firings, larger outdoor detonations, large-scale hydrodynamic tests, and at the Nevada Nuclear Security Site, underground sub-critical experiments.

  6. Los Alamos Explosives Performance Key to Stockpile Stewardship

    ScienceCinema

    Dattelbaum, Dana

    2016-07-12

    As the U.S. Nuclear Deterrent ages, one essential factor in making sure that the weapons will continue to perform as designed is understanding the fundamental properties of the high explosives that are part of a nuclear weapons system. As nuclear weapons go through life extension programs, some changes may be advantageous, particularly through the addition of what are known as "insensitive" high explosives that are much less likely to accidentally detonate than the already very safe "conventional" high explosives that are used in most weapons. At Los Alamos National Laboratory explosives research includes a wide variety of both large- and small-scale experiments that include small contained detonations, gas and powder gun firings, larger outdoor detonations, large-scale hydrodynamic tests, and at the Nevada Nuclear Security Site, underground sub-critical experiments.

  7. Thermal Cook-Off Experiments of the HMX Based High Explosive LX-04 to Characterize Violence with Varying Confinement

    NASA Astrophysics Data System (ADS)

    Garcia, Frank; Forbes, Jerry W.

    2005-07-01

    Thermal cook-off experiments were carried out using LX-04 explosive (85% HMX and 15% Viton by weight) with different levels of confinement to characterize the effect of confinement on the reaction violence. These experiments involved heating a porous LX-04 sample in a stainless steel container with varying container end plate thickness and assembly bolt diameter to control overall confinement. As expected, detonation did not occur and reducing the overall confinement lowered the reaction violence. Modeling was also performed using Ignition and Growth kinetics with reasonable agreement to the experiment. These results suggest that controlling the overall system confinement can modify the relative safety in a given scenario. This work was performed under the auspices of the U. S. Department of Energy by the University of California, Lawrence Livermore National Laboratory under Contract No. W-7405-Eng-48.

  8. New developments in pulsed fields at the US National High Magnetic Field Laboratory

    SciTech Connect

    Campbell, L.J.; Parkin, D.M.; Rickel, D.G.; Pernambuco-Wise, P.

    1996-12-01

    Los Alamos National Laboratory is a member of a consortium (with Florida State University and the University of Florida) to operate the National High Magnetic Field Laboratory (NHMFL), with funding from the National Science Foundation and the State of Florida. Los Alamos provides unique resources for its component of NHMFL in the form of a 1.4 GW inertial storage motor-generator for high field pulsed magnets and infrastructure for fields generated by flux compression. The NHMFL provides a user facility open to all qualified users, develops magnet technology in association with the private sector, and advances science and technology opportunities. The magnets in service at Los Alamos are of three types. Starting with the pre-existing explosive flux compression capability in 1991, NHMFL added capacitor-driven magnets in December, 1992, and a 20 tesla superconducting magnet in January, 1993. The capacitor-driven magnets continue to grow in diversity and accessibility, with four magnet stations now available for several different magnet types. Two magnets of unprecedented size and strength are nearing completion of assembly and design, respectively. Under final assembly is a quasi-continuous magnet that contains 90 MJ of magnetic energy at full field, and being designed is a non-destructive 100 T magnet containing 140 MJ.

  9. APPLICATION OF THE EMBEDDED FIBER OPTIC PROBE IN HIGH EXPLOSIVE DETONATION STUDIES: PBX-9502 AND LX-17

    SciTech Connect

    Hare, D; Goosman, D; Lorenz, K; Lee, E

    2006-09-26

    The Embedded Fiber Optic probe directly measures detonation speed continuously in time, without the need to numerically differentiate data, and is a new tool for measuring time-dependent as well as steady detonation speed to high accuracy. It consists of a custom-design optical fiber probe embedded in high explosive. The explosive is detonated and a refractive index discontinuity is produced in the probe at the location of the detonation front by the compression of the detonation. Because this index-jump tracks the detonation front a measurement of the Doppler shift of laser light reflected from the jump makes it possible to continuously measure detonation velocity with high spatial and temporal resolution. We have employed this probe with a Fabry-Perot-type laser Doppler velocimetry system additionally equipped with a special filter for reducing the level of non-Doppler shifted light relative to the signal. This is necessary because the index-jump signal is relatively weak compared to the return expected from a well-prepared surface in the more traditional and familiar example of material interface velocimetry. Our observations were carried out on a number of explosives but this work is focused on our results on PBX-9502 (95% TATB, 5% Kel-F) and LX-17 (92.5% TATB, 7.5% Kel-F) at varying initial charge density. Our measurements reveal a density dependence significantly lower than previous quoted values and lower than theoretical calculations. Our limited data on detonation speed dependence on wave curvature is in reasonable agreement with previous work using more standard methods and confirms deviation from the Wood-Kirkwood theoretical formula.

  10. Sandia Explosive Inventory and Information System

    SciTech Connect

    Clements, D.A.

    1994-08-01

    The Explosive Inventory and Information System (EIS) is being developed and implemented by Sandia National Laboratories (SNL) to incorporate a cradle to grave structure for all explosives and explosive containing devices and assemblies at SNL from acquisition through use, storage, reapplication, transfer or disposal. The system does more than track all material inventories. It provides information on material composition, characteristics, shipping requirements; life cycle cost information, plan of use; and duration of ownership. The system also provides for following the processes of explosive development; storage review; justification for retention; Resource, Recovery and Disposition Account (RRDA); disassembly and assembly; and job description, hazard analysis and training requirements for all locations and employees involved with explosive operations. In addition, other information systems will be provided through the system such as the Department of Energy (DOE) and SNL Explosive Safety manuals, the Navy`s Department of Defense (DoD) Explosive information system, and the Lawrence Livermore National Laboratories (LLNL) Handbook of Explosives.

  11. Eruptions on the fast track: application of Particle Tracking Velocimetry algorithms to visual and thermal high-speed videos of Strombolian explosions

    NASA Astrophysics Data System (ADS)

    Gaudin, Damien; Monica, Moroni; Jacopo, Taddeucci; Luca, Shindler; Piergiorgio, Scarlato

    2013-04-01

    Strombolian eruptions are characterized by mild, frequent explosions that eject gas and ash- to bomb-sized pyroclasts into the atmosphere. Studying these explosions is crucial, both for direct hazard assessment and for understanding eruption dynamics. Conventional thermal and optical imaging already allows characterizing several eruptive processes, but the quantification of key parameters linked to magma properties and conduit processes requires acquiring images at higher frequency. For example, high speed imaging already demonstrated how the size and the pressure of the gas bubble are linked to the decay of the ejection velocity of the particles, and the origin of the bombs, either fresh or recycled material, could be linked to their thermal evolution. However, the manual processing of the images is time consuming. Consequently, it does not allows neither the routine monitoring nor averaged statistics, since only a few relevant particles - usually the fastest - of a few explosions can be taken into account. In order to understand the dynamics of strombolian eruption, and particularly their cyclic behavior, the quantification of the total mass, heat and energy discharge are a crucial point. In this study, we use a Particle Tracking Velocimetry (PTV) algorithm jointly to traditional images processing to automatically extract the above parameters from visible and thermal high-speed videos of individual Strombolian explosions. PTV is an analysis technique where each single particle is detected and tracked during a series of images. Velocity, acceleration, and temperature can then be deduced and time averaged to get an extensive overview of each explosion. The suitability of PTV and its potential limitations in term of detection and representativity is investigated in various explosions of Stromboli (Italy), Yasur (Vanuatu) and Fuego (Guatemala) volcanoes. On most event, multiple sub-explosion are visible. In each sub-explosion, trends are noticeable : (1) the ejection

  12. A Risk Management Framework to Characterize Black Swan Risks: A Case Study of Lightning Effects on Insensitive High Explosives

    NASA Astrophysics Data System (ADS)

    Sanders, Gary A.

    Effective and efficient risk management processes include the use of high fidelity modeling and simulation during the concept exploration phase as part of the technology and risk assessment activities, with testing and evaluation tasks occurring in later design development phases. However, some safety requirements and design architectures may be dominated by the low probability/high consequence "Black Swan" vulnerabilities that require very early testing to characterize and efficiently mitigate. Failure to address these unique risks has led to catastrophic systems failures including the space shuttle Challenger, Deepwater Horizon, Fukushima nuclear reactor, and Katrina dike failures. Discovering and addressing these risks later in the design and development process can be very costly or even lead to project cancellation. This paper examines the need for risk management process adoption of early hazard phenomenology testing to inform the technical risk assessment, requirements definition and conceptual design. A case study of the lightning design vulnerability of the insensitive high explosives being used in construction, mining, demolition, and defense industries will be presented to examine the impact of this vulnerability testing during the concept exploration phase of the design effort. While these insensitive high explosives are far less sensitive to accidental initiation by fire, impact, friction or even electrical stimuli, their full range of sensitivities have not been characterized and ensuring safe engineering design and operations during events such as lightning storms requires vulnerability testing during the risk assessment phase.

  13. Dynamic Fracture Simulations of Explosively Loaded Cylinders

    SciTech Connect

    Arthur, Carly W.; Goto, D. M.

    2015-11-30

    This report documents the modeling results of high explosive experiments investigating dynamic fracture of steel (AerMet® 100 alloy) cylinders. The experiments were conducted at Lawrence Livermore National Laboratory (LLNL) during 2007 to 2008 [10]. A principal objective of this study was to gain an understanding of dynamic material failure through the analysis of hydrodynamic computer code simulations. Two-dimensional and three-dimensional computational cylinder models were analyzed using the ALE3D multi-physics computer code.

  14. Skin explosion of double-layer conductors in fast-rising high magnetic fields

    SciTech Connect

    Chaikovsky, S. A. Datsko, I. M.; Labetskaya, N. A.; Ratakhin, N. A.

    2014-04-15

    An experiment has been performed to study the electrical explosion of thick cylindrical conductors using the MIG pulsed power generator capable of producing a peak current of 2.5 MA within 100 ns rise time. The experimental goal was to compare the skin explosion of a solid conductor with that of a double-layer conductor whose outer layer had a lower conductivity than the inner one. It has been shown that in magnetic fields of peak induction up to 300 T and average induction rise rate 3 × 10{sup 9} T/s, the double-layer structure of a conductor makes it possible to achieve higher magnetic induction at the conductor surface before it explodes. This can be accounted for, in particular, by the reduction of the ratio of the Joule heat density to the energy density of the magnetic field at the surface of a double-layer conductor due to redistribution of the current density over the conductor cross section.

  15. Heavy and Superheavy Elements Production in High Intensive Neutron Fluxes of Explosive Process

    NASA Astrophysics Data System (ADS)

    Lutostansky, Yu. S.; Lyashuk, V. I.; Panov, I. V.

    2015-06-01

    Mathematical model of heavy and superheavy nuclei production in intensive pulsed neutron fluxes of explosive process is developed. The pulse character of the process allows dividing it in time into two stages: very short rapid process of multiple neutron captures with higher temperature and very intensive neutron fluxes, and relatively slower process with lesser temperature and neutron fluxes. The model was also extended for calculation of the transuranium yields in nuclear explosions takes into account the adiabatic character of the process, the probabilities of delayed fission, and the emission of delayed neutrons. Also the binary starting target isotopes compositions were included. Calculations of heavy transuranium and transfermium nuclei production were made for "Mike", "Par" and "Barbel" experiments, performed in USA. It is shown that the production of transfermium neutron-rich nuclei and superheavy elements with A ~ 295 is only possible when using binary mixture of starting isotopes with the significant addition of heavy components, such as long-lived isotopes of curium, or californium.

  16. Vapor Explosions

    NASA Astrophysics Data System (ADS)

    Berthoud, Georges

    A vapor explosion results from the rapid and intense heat transfer that may follow contact between a hot liquid and a cold, more volatile one. Because it can happen during severe-accident sequences of a nuclear power plan, that is, when a large part of the core is molten, vapor explosions have been widely studied. The different sequences of a vapor explosion are presented, including premixing, triggering, propagation, and expansion. Typical experimental results are also analyzed to understand the involved physics. Then the different physics involved in the sequences are addressed, as well as the present experimental program.

  17. Parametric Explosion Spectral Model

    SciTech Connect

    Ford, S R; Walter, W R

    2012-01-19

    Small underground nuclear explosions need to be confidently detected, identified, and characterized in regions of the world where they have never before occurred. We develop a parametric model of the nuclear explosion seismic source spectrum derived from regional phases that is compatible with earthquake-based geometrical spreading and attenuation. Earthquake spectra are fit with a generalized version of the Brune spectrum, which is a three-parameter model that describes the long-period level, corner-frequency, and spectral slope at high-frequencies. Explosion spectra can be fit with similar spectral models whose parameters are then correlated with near-source geology and containment conditions. We observe a correlation of high gas-porosity (low-strength) with increased spectral slope. The relationship between the parametric equations and the geologic and containment conditions will assist in our physical understanding of the nuclear explosion source.

  18. The Hazards of Reactive Chemicals in High School Laboratories.

    ERIC Educational Resources Information Center

    Forlin, Peter

    Chemical reactivity is a major area of risk in high school laboratories. This paper reports on a study that has provided a research-based framework for risk management in Australian chemical education. The chemical practice model of risk management is considered with respect to kinetic factors; catalysts; concentrations and proportions;…

  19. Laboratory 15 kV high voltage solar array facility

    NASA Technical Reports Server (NTRS)

    Kolecki, J. C.; Gooder, S. T.

    1976-01-01

    The laboratory high voltage solar array facility is a photoelectric power generating system. Consisting of nine modules with over 23,000 solar cells, the facility is capable of delivering more than a kilowatt of power. The physical and electrical characteristics of the facility are described.

  20. Upgrading the Laboratory Preparation of High School Teachers

    ERIC Educational Resources Information Center

    Powers, Jack W.; Scamehorn, Richard G.

    1970-01-01

    Describes a college program designed to upgrade the laboratory experience of selected high school chemistry teachers. Small groups of teachers work with college faculty on chemistry problems each weekend. Problems investigated include the use of pH meters, X-ray diffraction, computers, and experiments in chromatography, spectroscopy radiochemistry…

  1. Characterizing High School Students' Written Explanations in Biology Laboratories

    ERIC Educational Resources Information Center

    Peker, Deniz; Wallace, Carolyn S.

    2011-01-01

    The purpose of this qualitative interpretive research study was to examine high school students' written scientific explanations during biology laboratory investigations. Specifically, we characterized the types of epistemologies and forms of reasoning involved in students' scientific explanations and students' perceptions of scientific…

  2. The Science Laboratory Experiences of Utah's High School Students

    ERIC Educational Resources Information Center

    Campbell, Todd

    2007-01-01

    This research investigated the extent to which science laboratory experiences encountered by Utah high school students aligned with reform efforts outlined in national standards documents. Through both quantitative and qualitative methods the findings revealed that while there were instances of alignment found between science laboratory…

  3. A Laboratory Practical Exam for High School Chemistry

    ERIC Educational Resources Information Center

    Rhodes, Michelle M.

    2010-01-01

    A station-based laboratory practical exam for first-year high school chemistry students is described. Students move individually through six stations meant to authentically assess both basic lab skills and problem-solving skills utilized throughout the year. The exam can be completed in an approximately 85 min lab period and can be easily adapted…

  4. Summary of efficiency testing of standard and high-capacity high-efficiency particulate air filters subjected to simulated tornado depressurization and explosive shock waves

    SciTech Connect

    Smith, P.R.; Gregory, W.S.

    1985-04-01

    Pressure transients in nuclear facility air cleaning systems can originate from natural phenomena such as tornadoes or from accident-induced explosive blast waves. This study was concerned with the effective efficiency of high-efficiency particulate air (HEPA) filters during pressure surges resulting from simulated tornado and explosion transients. The primary objective of the study was to examine filter efficiencies at pressure levels below the point of structural failure. Both standard and high-capacity 0.61-m by 0.61-m HEPA filters were evaluated, as were several 0.2-m by 0.2-m HEPA filters. For a particular manufacturer, the material release when subjected to tornado transients is the same (per unit area) for both the 0.2-m by 0.2-m and the 0.61-m by 0.61-m filters. For tornado transients, the material release was on the order of micrograms per square meter. When subjecting clean HEPA filters to simulated tornado transients with aerosol entrained in the pressure pulse, all filters tested showed a degradation of filter efficiency. For explosive transients, the material release from preloaded high-capacity filters was as much as 340 g. When preloaded high-capacity filters were subjected to shock waves approximately 50% of the structural limit level, 1 to 2 mg of particulate was released.

  5. Explosive detection using high-volume vapor sampling and analysis by trained canines and ultra-trace detection equipment

    NASA Astrophysics Data System (ADS)

    Fisher, Mark; Sikes, John; Prather, Mark

    2004-09-01

    The dog's nose is an effective, highly-mobile sampling system, while the canine olfactory organs are an extremely sensitive detector. Having been trained to detect a wide variety of substances with exceptional results, canines are widely regarded as the 'gold standard' in chemical vapor detection. Historically, attempts to mimic the ability of dogs to detect vapors of explosives using electronic 'dogs noses' has proven difficult. However, recent advances in technology have resulted in development of detection (i.e., sampling and sensor) systems with performance that is rapidly approaching that of trained canines. The Nomadics Fido was the first sensor to demonstrate under field conditions the detection of landmines with performance approaching that of canines. More recently, comparative testing of Fido against canines has revealed that electronic vapor detection, when coupled with effective sampling methods, can produce results comparable to that of highly-trained canines. The results of these comparative tests will be presented, as will recent test results in which explosives hidden in cargo were detected using Fido with a high-volume sampling technique. Finally, the use of canines along with electronic sensors will be discussed as a means of improving the performance and expanding the capabilities of both methods.

  6. Laboratory Astrophysics on High Power Lasers and Pulsed Power Facilities

    SciTech Connect

    Remington, B A

    2002-02-05

    Over the past decade a new genre of laboratory astrophysics has emerged, made possible by the new high energy density (HED) experimental facilities, such as large lasers, z-pinch generators, and high current particle accelerators. (Remington, 1999; 2000; Drake, 1998; Takabe, 2001) On these facilities, macroscopic collections of matter can be created in astrophysically relevant conditions, and its collective properties measured. Examples of processes and issues that can be experimentally addressed include compressible hydrodynamic mixing, strong shock phenomena, radiative shocks, radiation flow, high Mach-number jets, complex opacities, photoionized plasmas, equations of state of highly compressed matter, and relativistic plasmas. These processes are relevant to a wide range of astrophysical phenomena, such as supernovae and supernova remnants, astrophysical jets, radiatively driven molecular clouds, accreting black holes, planetary interiors, and gamma-ray bursts. These phenomena will be discussed in the context of laboratory astrophysics experiments possible on existing and future HED facilities.

  7. Determining the TNT equivalence of gram-sized explosive charges using shock-wave shadowgraphy and high-speed video recording

    NASA Astrophysics Data System (ADS)

    Hargather, Michael

    2005-11-01

    Explosive materials are routinely characterized by their TNT equivalence. This can be determined by chemical composition calculations, measurements of shock wave overpressure, or measurements of the shock wave position vs. time. However, TNT equivalence is an imperfect criterion because it is only valid at a given radius from the explosion center (H. Kleine et al., Shock Waves 13(2):123-138, 2003). Here we use a large retroreflective shadowgraph system and a high-speed digital video camera to image the shock wave and record its location vs. time. Optical data obtained from different explosions can be combined to determine a characteristic shock wave x-t diagram, from which the overpressure and the TNT equivalent are determined at any radius. This method is applied to gram-sized triacetone triperoxide (TATP) charges. Such small charges can be used inexpensively and safely for explosives research.

  8. Characterization of ANFO explosive by high accuracy ESI(±)-FTMS with forensic identification on real samples by EASI(-)-MS.

    PubMed

    Hernandes, Vinicius Veri; Franco, Marcos Fernado; Santos, Jandyson Machado; Melendez-Perez, Jose J; de Morais, Damila Rodrigues; Rocha, Werickson Fortunato de Carvalho; Borges, Rodrigo; de Souza, Wanderley; Zacca, Jorge Jardim; Logrado, Lucio Paulo Lima; Eberlin, Marcos Nogueira; Correa, Deleon Nascimento

    2015-04-01

    Ammonium nitrate fuel oil (ANFO) is an explosive used in many civil applications. In Brazil, ANFO has unfortunately also been used in criminal attacks, mainly in automated teller machine (ATM) explosions. In this paper, we describe a detailed characterization of the ANFO composition and its two main constituents (diesel and a nitrate explosive) using high resolution and accuracy mass spectrometry performed on an FT-ICR-mass spectrometer with electrospray ionization (ESI(±)-FTMS) in both the positive and negative ion modes. Via ESI(-)-MS, an ion marker for ANFO was characterized. Using a direct and simple ambient desorption/ionization technique, i.e., easy ambient sonic-spray ionization mass spectrometry (EASI-MS), in a simpler, lower accuracy but robust single quadrupole mass spectrometer, the ANFO ion marker was directly detected from the surface of banknotes collected from ATM explosion theft.

  9. Explosion depths for phreatomagmatic eruptions

    NASA Astrophysics Data System (ADS)

    Valentine, Greg A.; Graettinger, Alison H.; Sonder, Ingo

    2014-05-01

    Subsurface phreatomagmatic explosions can result from the interaction of ascending magma with groundwater. Experiments over a wide range of energies show that for a given energy there is a depth below which an explosion will be contained within the subsurface (not erupt), and there is a corresponding shallower depth that will optimize ejecta dispersal. We combine these relationships with constraints on the energies of phreatomagmatic explosions at maar-diatreme volcanoes and show that most eruptions are likely sourced by explosions in the uppermost ~200 m, and even shallower ones (<100 m) are likely to dominate deposition onto tephra rings. Most explosions below ~200 m will not erupt but contribute to formation of, and to the vertical mixing of materials within, a diatreme (vent structure), with only rare very high energy explosions between ~200 and 500 m erupting. Similar constraints likely apply at other volcanoes that experience phreatomagmatic explosions.

  10. Model-Based Development of a Small-Scale Experiment for Non-Shock Ignition of High Explosives

    NASA Astrophysics Data System (ADS)

    White, Bradley; Springer, H.; Reaugh, J.

    2013-06-01

    We demonstrate a model-based approach for developing small-scale experiments for non-shock ignition of high explosives (HEs) that are representative of abnormal environmental conditions. While small-scale experiments are often favored over large-scale testing since costs are lower and samples sizes are amenable to early stage HE formulation, concerns remain about the ability to predict full-scale non-shock ignition response. Our approach is to perform simulations of full-scale systems (i.e., Skid test) to identify the localized material extrema states (e.g., pressure, pressure duration, shear stress, strain-rate) underlying the non-shock ignition mechanism. The extrema states then provide a metric for iterative model-based development of small-scale experiments using a drop-hammer system. We performed these simulations using the HERMES (High Explosive Response to MEchanical Stimuli) model in the multiphysics code, ALE3D. Optimized experimental geometries reach 10s MPa pressures over 1-3 ms durations while inducing a large degree of shear. The results of the experimental development and the effects of design variations on non-shock initiation response of Comp B will be presented. This work performed under the auspices of the U.S. DOE by LLNL under Contract DE-AC52-07NA27344. This work was funded in part by the Joint DoD-DOE Munitions Program.

  11. Single and double shock initiation modelling for high explosive materials in last three decades

    NASA Astrophysics Data System (ADS)

    Hussain, T.; Yan, Liu

    2016-08-01

    The explosives materials are normally in an energetically metastable state. These can undergo rapid chemical decomposition only if sufficient energy has first been added to get the process started. Such energy can be provided by shocks. To predict the response of these materials under impacts of shocks of different strengths and durations and at various conditions, mathematical models are used. During the last three decades, a lot of research has been carried out and several shock initiation models have been presented. The models can be divided into continuum based and physics based models. In this study the single and double shock initiation models presented in last three decades have been reviewed and the ranges of their application has been discussed.

  12. Experimental Method to Determine the Detonation Characteristics of Very Non-Ideal High Explosives

    NASA Astrophysics Data System (ADS)

    Baudin, Gerard

    2005-07-01

    Common experimental configurations used to determine HE detonation velocity-curvature are right circular cylinders detonated in air. The steadily propagating detonation front is curved and its velocity depends upon the diameter of the cylinder. This configuration requires several experiments with different diameters and sufficiently long cylinders to assume a steadily propagating detonation front. This last hypothesis is practically not achieved for non-ideal HE using reasonably long cylinders. To elude this problem, a special explosive device called ``logosphere,'' developed by CEA, has been adapted to non ideal HE. It provides a well define spherically diverging detonation wave and allows measurements of the detonation velocity-curvature relationship by means of piezoelectric pins without any perturbation. VISAR and DLI diagnostics record the material velocities at the rear surface of HE through transparent windows. The particle velocity values are used to determine the curved detonation states using the detonation velocity-acceleration-curvature model of Louis Brun.

  13. Quantitative understanding of explosive stimulus transfer

    NASA Technical Reports Server (NTRS)

    Schimmel, M. L.

    1973-01-01

    The mechanisms of detonation transfer across hermetically sealed interfaces created by necessary interruptions in high explosive trains, such as at detonators to explosive columns, field joints in explosive columns, and components of munitions fuse trains are demostrated. Reliability of detonation transfer is limited by minimizing explosive quantities, the use of intensitive explosives for safety, and requirements to propagate across gaps and angles dictated by installation and production restraints. The major detonation transfer variables studied were: explosive quanity, sensitivity, and thickness, and the separation distances between donor and acceptor explosives.

  14. Dynamics of the detonation products of a TATB based high explosive: Photon Doppler Velocimetry and high-speed digital shadowgraphy of expanding species

    NASA Astrophysics Data System (ADS)

    Sollier, Arnaud; Bouyer, Viviane; Terzulli, Louis-Pierre; Doucet, Michel; Hebert, Philippe; Decaris, Lionel

    2011-06-01

    The present investigation attempts to further improve our experimental characterization of the reaction zone in plastic bonded high explosives, by focusing on the dynamic of expansion of the detonation products during its initial stage. To this purpose, we performed measurements of the free surface velocity history of the detonating explosive using a PDV velocimeter system developped at CEA. We also used digital high-speed shadowgraphy to characterize the shape and speed of the products as they release from the bare charge free surface. In our experiments, we used cylindrical samples of an insensitive triaminotrinitrobenzene (TATB) composition having a density about 1.86 g/cc. Most of the experiments were performed in a cylindrical chamber under vacuum, but some shots were also performed with air at atmospheric conditions. The results of these experiments are compared with those of thin push-plate and explosive-window interface velocity measurements performed in the same conditions, which allow to give new insight into the reactions zone. Numerical simulations with different reactive flow models are also presented and found to be in good agreement with experiments.

  15. Seal Monitoring System for an Explosive Containment Vessel

    SciTech Connect

    Pastrnak, J W; Henning, C D; Switzer, V A; Grundler, W; Holloway, J R; Morrison, J J; Hafner, R S

    2004-06-28

    Researchers at Lawrence Livermore National Laboratory are developing high-performance explosive firing vessels to contain (one time) explosive detonations that contain toxic metals and hazardous gases. The filament-wound polymer composite vessels are designed to contain up to 80 lb (TNT equivalent) explosive in a 2-meter sphere without leakage. So far, two half-scale (1-meter diameter) vessels have been tested; one up to 150% of the design explosive limit. Peak dynamic pressures in excess of 280 MPa (40 Ksi) in the vessel were calculated and measured. Results indicated that there was a small amount of gas and particle leakage past the first two of the seven o-ring seals. However, the remaining five seals prevented any transient leakage of the toxic gases and particulates out of the vessel. These results were later confirmed by visual inspection and particulate analysis of swipes taken from the sealing surfaces.

  16. The spectacular evolution of Supernova 1996al over 15 years: a low energy explosion of a stripped massive star in a highly structured environment

    NASA Astrophysics Data System (ADS)

    Benetti, Stefano

    2016-06-01

    The final fate of massive stars is not well explored and depending on the stellar mass may have very much different outputs, ranging from very energetic explosions (e.g. GRB-SNe) to direct collapse on black-holes with very weak or not explosion at all (Heger, Woosley, & Baraffe, 2005). Here I present the case of SN 1996al. I describe the physical properties of this luminous supernova in the framework of a very weak explosion (kinetic energy of 1.6 x 10^(50 erg)), where the bolometric luminosity is sustained by the conversion of the kinetic energy into radiation thanks to the interaction between a low mass ( 1.15 M_{⊙}) , 87% of which is Helium, the remaining is Hydrogen) symmetric ejecta with an highly asymmetric circumstellar material. The detection of Hα emission in pre-explosion archive images suggests that the progenitor of SN 1996al was most likely a massive star ( 25 M_{⊙}) ZAMS) that had lost a large fraction of its hydrogen envelope before explosion, and was hence embedded in a H-rich cocoon. The low-mass ejecta and modest kinetic energy of the explosion are then explained with massive fallback of material into the compact remnant, a 7 ‑ 8 M_{⊙}) black hole. Finally, I will try to place this particularly interesting SN in the framework of the SNIIn zoo.

  17. Application of ultra-high-speed optical observations and high-speed x-ray radiography measurements to the study of explosively driven copper tube expansion

    NASA Astrophysics Data System (ADS)

    Voltz, C.; Lagrange, J. M.; Besnard, G.; Etchessahar, B.

    2008-11-01

    The purpose of this experiment is to study the behavior of expanding copper cylinder under explosive loading. The apparatus is designed to submit the target to high strain, high stain rate in quasi-plane deformation constraints. Using high-speed cinematography we evaluate the expansion characteristics and observe plastic instability and striction phenomena. Stereoscopic observation is used to give us the possibility to reconstruct the 3D shape and to access to free moving and strain fields. In order to measure the residual thickness and characterize striction patterns, we employ a flash X-Ray imaging diagnostic. Experimental results are presented and compared with hydrocode calculations.

  18. Development of highly sensitive and selective antibodies for the detection of the explosive pentaerythritol tetranitrate (PETN) by bioisosteric replacement.

    PubMed

    Hesse, Almut; Biyikal, Mustafa; Rurack, Knut; Weller, Michael G

    2016-02-01

    An improved antibody against the explosive pentaerythritol tetranitrate (PETN) was developed. The immunogen was designed by the concept of bioisosteric replacement, which led to an excellent polyclonal antibody with extreme selectivity and immunoassays of very good sensitivity. Compounds such as nitroglycerine, 2,4,6-trinitrotoluene, 1,3,5-trinitrobenzene, hexogen (RDX), 2,4,6-trinitroaniline, 1,3-dinitrobenzene, octogen (HMX), triacetone triperoxide, ammonium nitrate, 2,4,6-trinitrophenol and nitrobenzene were tested for potential cross-reactivity. The detection limit of a competitive enzyme-linked immunosorbent assay was determined to be around 0.5 µg/l. The dynamic range of the assay was found to be between 1 and 1000 µg/l, covering a concentration range of three decades. This work shows the successful application of the bioisosteric concept in immunochemistry by exchange of a nitroester to a carbonate diester. The antiserum might be used for the development of quick tests, biosensors, microtitration plate immunoassays, microarrays and other analytical methods for the highly sensitive detection of PETN, an explosive frequently used by terrorists, exploiting the extreme difficulty of its detection.

  19. Communication: Two-step explosion processes of highly charged fullerene cations C60q+ (q = 20-60)

    NASA Astrophysics Data System (ADS)

    Yamazaki, Kaoru; Nakamura, Takashi; Niitsu, Naoyuki; Kanno, Manabu; Ueda, Kiyoshi; Kono, Hirohiko

    2014-09-01

    To establish the fundamental understanding of the fragmentation dynamics of highly positive charged nano- and bio-materials, we carried out on-the-fly classical trajectory calculations on the fragmentation dynamics of C60q+ (q = 20-60). We used the UB3LYP/3-21G level of density functional theory and the self-consistent charge density-functional based tight-binding theory. For q ≥ 20, we found that a two-step explosion mechanism governs the fragmentation dynamics: C60q+ first ejects singly and multiply charged fast atomic cations Cz+ (z ≥ 1) via Coulomb explosions on a timescale of 10 fs to stabilize the remaining core cluster. Thermal evaporations of slow atomic and molecular fragments from the core cluster subsequently occur on a timescale of 100 fs to 1 ps. Increasing the charge q makes the fragments smaller. This two-step mechanism governs the fragmentation dynamics in the most likely case that the initial kinetic energy accumulated upon ionization to C60q+ by ion impact or X-ray free electron laser is larger than 100 eV.

  20. The student perspective of high school laboratory experiences

    NASA Astrophysics Data System (ADS)

    Lambert, R. Mitch

    High school science laboratory experiences are an accepted teaching practice across the nation despite a lack of research evidence to support them. The purpose of this study was to examine the perspective of students---stakeholders often ignored---on these experiences. Insight into the students' perspective was explored progressively using a grounded theory methodology. Field observations of science classrooms led to an open-ended survey of high school science students, garnering 665 responses. Twelve student interviews then focused on the data and questions evolving from the survey. The student perspective on laboratory experiences revealed varied information based on individual experience. Concurrent analysis of the data revealed that although most students like (348/665) or sometimes like (270/665) these experiences, some consistent factors yielded negative experiences and prompted suggestions for improvement. The category of responses that emerged as the core idea focused on student understanding of the experience. Students desire to understand the why do, the how to, and the what it means of laboratory experiences. Lacking any one of these, the experience loses educational value for them. This single recurring theme crossed the boundaries of age, level in school, gender, and even the student view of lab experiences as positive or negative. This study suggests reflection on the current laboratory activities in which science teachers engage their students. Is the activity appropriate (as opposed to being merely a favorite), does it encourage learning, does it fit, does it operate at the appropriate level of inquiry, and finally what can science teachers do to integrate these activities into the classroom curriculum more effectively? Simply stated, what can teachers do so that students understand what to do, what's the point, and how that point fits into what they are learning outside the laboratory?

  1. Design issues for a laboratory high gain fusion facility

    SciTech Connect

    Hogan, W.J.

    1987-11-02

    In an inertial fusion laboratory high gain facility, experiments will be carried out with up to 1000 MJ of thermonuclear yield. The experiment area of such a facility will include many systems and structures that will have to operate successfully in the difficult environment created by the sudden large energy release. This paper estimates many of the nuclear effects that will occur, discusses the implied design issues and suggests possible solutions so that a useful experimental facility can be built. 4 figs.

  2. A high-porosity limit for the transition from conductive to convective burning in gas-permeable explosives

    SciTech Connect

    Kagan, Leonid; Sivashinsky, Gregory

    2010-02-15

    The experimentally known phenomenon of an abrupt transition from slow conductive to fast convective (penetrative) burning in a confined gas-permeable explosive is discussed. A simple model, involving only the most essential physical ingredients, is formulated and analyzed. In addition to commonly utilized assumptions of the solid-gas thermal equilibrium, validity of Darcy's law, immobility of the solid phase, and one-step Arrhenius kinetics, the model employs the distinguished limit combining high-porosity with high solid/gas density ratio, resulting in conservation of enthalpy, advantageous for theoretical analysis. A good qualitative agreement between theoretical and experimental dependencies is obtained. The transition is triggered by a localized autoignition in the extended resistance-induced preheat zone formed ahead of the advancing deflagration, provided the pressure difference between hot gas products and gases deep inside the pores of the unburned solid exceeds a certain critical level. In line with observations the critical overpressure increases with diminishing permeability. (author)

  3. High luminosity, slow ejecta and persistent carbon lines: SN 2009dc challenges thermonuclear explosion scenarios

    NASA Astrophysics Data System (ADS)

    Taubenberger, S.; Benetti, S.; Childress, M.; Pakmor, R.; Hachinger, S.; Mazzali, P. A.; Stanishev, V.; Elias-Rosa, N.; Agnoletto, I.; Bufano, F.; Ergon, M.; Harutyunyan, A.; Inserra, C.; Kankare, E.; Kromer, M.; Navasardyan, H.; Nicolas, J.; Pastorello, A.; Prosperi, E.; Salgado, F.; Sollerman, J.; Stritzinger, M.; Turatto, M.; Valenti, S.; Hillebrandt, W.

    2011-04-01

    Extended optical and near-IR observations reveal that SN 2009dc shares a number of similarities with normal Type Ia supernovae (SNe Ia), but is clearly overluminous, with a (pseudo-bolometric) peak luminosity of log (L) = 43.47 (erg s-1). Its light curves decline slowly over half a year after maximum light [Δm15(B)true= 0.71], and the early-time near-IR light curves show secondary maxima, although the minima between the first and the second peaks are not very pronounced. The bluer bands exhibit an enhanced fading after ˜200 d, which might be caused by dust formation or an unexpectedly early IR catastrophe. The spectra of SN 2009dc are dominated by intermediate-mass elements and unburned material at early times, and by iron-group elements at late phases. Strong C II lines are present until ˜2 weeks past maximum, which is unprecedented in thermonuclear SNe. The ejecta velocities are significantly lower than in normal and even subluminous SNe Ia. No signatures of interaction with a circumstellar medium (CSM) are found in the spectra. Assuming that the light curves are powered by radioactive decay, analytic modelling suggests that SN 2009dc produced ˜1.8 M⊙ of 56Ni assuming the smallest possible rise time of 22 d. Together with a derived total ejecta mass of ˜2.8 M⊙, this confirms that SN 2009dc is a member of the class of possible super-Chandrasekhar-mass SNe Ia similar to SNe 2003fg, 2006gz and 2007if. A study of the hosts of SN 2009dc and other superluminous SNe Ia reveals a tendency of these SNe to explode in low-mass galaxies. A low metallicity of the progenitor may therefore be an important prerequisite for producing superluminous SNe Ia. We discuss a number of possible explosion scenarios, ranging from super-Chandrasekhar-mass white-dwarf progenitors over dynamical white-dwarf mergers and Type I? SNe to a core-collapse origin of the explosion. None of the models seems capable of explaining all properties of SN 2009dc, so that the true nature of this SN

  4. Application of portable optical laboratory in high schools and colleges

    NASA Astrophysics Data System (ADS)

    Altshuler, Gregory B.; Belashenkov, Nickolai R.; Ermolaev, Vladimir S.; Inochkin, Mickle V.; Karasev, Vyatcheslav B.

    1995-10-01

    The present paper describes the experience of application of portable optical laboratory in optical practicum developed directly for training and demonstrations of basic optical laws and phenomena in high-schools, colleges and nontechnical universities all over Russia. The laboratory includes the portable optical platform with built-in laser and lamp sources, kit of optical components and software. These accessories provide the attractive and smart teaching in general optics during lectures, lessons and practice at schools and colleges. The portable optical laboratory provides 28 basic lab works and demonstrations in reflection, refraction, absorption and dispersion of light, interference, diffraction, polarization of light, image formation and waveguide propagation of light in optical fibers. Due to their interdependence one can teach and learn a whole course of general optics. The individual work of students and school children with optical kit stimulates and develops their creative abilities and experimental skills, as well increases the effectiveness of education. The kit is provided with optional elements for a number of extra experiments with holography, polarizing light propagation, simple optical devices etc. These extensions allow to modify the education process according to teacher's point of view. The conception of optical class-room based on portable optical laboratories is discussed. The effectiveness of individual and small-group training is analyzed.

  5. Measurement of carbon condensates using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene

    DOE PAGESBeta

    Bagge-Hansen, M.; Lauderbach, L.; Hodgin, R.; Bastea, S.; Fried, L.; Jones, A.; van Buuren, T.; Hansen, D.; Benterou, J.; May, C.; et al

    2015-06-24

    In this study, the dynamics of carbon condensation in detonating high explosives remains controversial. Detonation model validation requires data for processes occurring at nanometer length scales on time scales ranging from nanoseconds to microseconds. A new detonation end station has been commissioned to acquire and provide time-resolved small-angle x-ray scattering (SAXS) from detonating explosives. Hexanitrostilbene (HNS) was selected as the first to investigate due to its ease of initiation using exploding foils and flyers, vacuum compatibility, high thermal stability, and stoichiometric carbon abundance that produces high carbon condensate yields. The SAXS data during detonation, collected with 300 ns time resolution,more » provide unprecedented signal fidelity over a broad q-range. This fidelity permits the first analysis of both the Guinier and Porod/power-law regions of the scattering profile during detonation, which contains information about the size and morphology of the resultant carbon condensate nanoparticles. To bolster confidence in these data, the scattering angle and intensity were additionally cross-referenced with a separate, highly calibrated SAXS beamline. The data show that HNS produces carbon particles with a radius of gyration of 2.7 nm in less than 400 ns after the detonation front has passed, and this size and morphology are constant over the next several microseconds. These data directly contradict previous pioneering work on RDX/TNT mixtures and TATB, where observations indicate significant particle growth (50% or more) continues over several microseconds. The power-law slope is about -3, which is consistent with a complex disordered, irregular, or folded sp2 sub-arrangement within a relatively monodisperse structure possessing radius of gyration of 2.7 nm after the detonation of HNS.« less

  6. Measurement of carbon condensation using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene

    SciTech Connect

    Bagge-Hansen, M.; Lauderbach, L. M.; Hodgin, R.; Bastea, S.; Fried, L.; Jones, A.; van Buuren, T.; Hansen, D.; Benterou, J.; May, C.; Graber, T.; Jensen, B. J.; Ilavsky, J.; Willey, T. M.

    2015-06-24

    The dynamics of carboncondensation in detonating high explosives remains controversial. Detonation model validation requires data for processes occurring at nanometer length scales on time scales ranging from nanoseconds to microseconds. A new detonation endstation has been commissioned to acquire and provide time-resolved small-angle x-ray scattering (SAXS) from detonating explosives. Hexanitrostilbene (HNS) was selected as the first to investigate due to its ease of initiation using exploding foils and flyers, vacuum compatibility, high thermal stability, and stoichiometric carbon abundance that produces high carbon condensate yields. The SAXS data during detonation, collected with 300 ns time resolution, provide unprecedented signal fidelity over a broad q-range. This fidelity permits the first analysis of both the Guinier and Porod/power-law regions of the scattering profile during detonation, which contains information about the size and morphology of the resultant carbon condensate nanoparticles. To bolster confidence in these data, the scattering angle and intensity were additionally cross-referenced with a separate, highly calibrated SAXS beamline. The data show that HNS produces carbon particles with a radius of gyration of 2.7 nm in less than 400 ns after the detonation front has passed, and this size and morphology are constant over the next several microseconds. These data directly contradict previous pioneering work on RDX/TNT mixtures and TATB, where observations indicate significant particle growth (50% or more) continues over several microseconds. As a result, the power-law slope is about –3, which is consistent with a complex disordered, irregular, or folded sp2 sub-arrangement within a relatively monodisperse structure possessing radius of gyration of 2.7 nm after the detonation of HNS.

  7. Measurement of carbon condensates using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene

    SciTech Connect

    Bagge-Hansen, M.; Lauderbach, L.; Hodgin, R.; Bastea, S.; Fried, L.; Jones, A.; van Buuren, T.; Hansen, D.; Benterou, J.; May, C.; Graber, T.; Jensen, B. J.; Ilavsky, J.; Willey, T. M.

    2015-06-24

    In this study, the dynamics of carbon condensation in detonating high explosives remains controversial. Detonation model validation requires data for processes occurring at nanometer length scales on time scales ranging from nanoseconds to microseconds. A new detonation end station has been commissioned to acquire and provide time-resolved small-angle x-ray scattering (SAXS) from detonating explosives. Hexanitrostilbene (HNS) was selected as the first to investigate due to its ease of initiation using exploding foils and flyers, vacuum compatibility, high thermal stability, and stoichiometric carbon abundance that produces high carbon condensate yields. The SAXS data during detonation, collected with 300 ns time resolution, provide unprecedented signal fidelity over a broad q-range. This fidelity permits the first analysis of both the Guinier and Porod/power-law regions of the scattering profile during detonation, which contains information about the size and morphology of the resultant carbon condensate nanoparticles. To bolster confidence in these data, the scattering angle and intensity were additionally cross-referenced with a separate, highly calibrated SAXS beamline. The data show that HNS produces carbon particles with a radius of gyration of 2.7 nm in less than 400 ns after the detonation front has passed, and this size and morphology are constant over the next several microseconds. These data directly contradict previous pioneering work on RDX/TNT mixtures and TATB, where observations indicate significant particle growth (50% or more) continues over several microseconds. The power-law slope is about -3, which is consistent with a complex disordered, irregular, or folded sp2 sub-arrangement within a relatively monodisperse structure possessing radius of gyration of 2.7 nm after the detonation of HNS.

  8. Measurement of carbon condensates using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene

    SciTech Connect

    Bagge-Hansen, M.; Lauderbach, L.; Hodgin, R.; Bastea, S.; Fried, L.; Jones, A.; Buuren, T. van; Hansen, D.; Benterou, J.; May, C.; Willey, T. M.; Graber, T.; Jensen, B. J.; Ilavsky, J.

    2015-06-28

    The dynamics of carbon condensation in detonating high explosives remains controversial. Detonation model validation requires data for processes occurring at nanometer length scales on time scales ranging from nanoseconds to microseconds. A new detonation endstation has been commissioned to acquire and provide time-resolved small-angle x-ray scattering (SAXS) from detonating explosives. Hexanitrostilbene (HNS) was selected as the first to investigate due to its ease of initiation using exploding foils and flyers, vacuum compatibility, high thermal stability, and stoichiometric carbon abundance that produces high carbon condensate yields. The SAXS data during detonation, collected with 300 ns time resolution, provide unprecedented signal fidelity over a broad q-range. This fidelity permits the first analysis of both the Guinier and Porod/power-law regions of the scattering profile during detonation, which contains information about the size and morphology of the resultant carbon condensate nanoparticles. To bolster confidence in these data, the scattering angle and intensity were additionally cross-referenced with a separate, highly calibrated SAXS beamline. The data show that HNS produces carbon particles with a radius of gyration of 2.7 nm in less than 400 ns after the detonation front has passed, and this size and morphology are constant over the next several microseconds. These data directly contradict previous pioneering work on RDX/TNT mixtures and TATB, where observations indicate significant particle growth (50% or more) continues over several microseconds. The power-law slope is about −3, which is consistent with a complex disordered, irregular, or folded sp{sup 2} sub-arrangement within a relatively monodisperse structure possessing radius of gyration of 2.7 nm after the detonation of HNS.

  9. Measurement of carbon condensates using small-angle x-ray scattering during detonation of the high explosive hexanitrostilbene

    NASA Astrophysics Data System (ADS)

    Bagge-Hansen, M.; Lauderbach, L.; Hodgin, R.; Bastea, S.; Fried, L.; Jones, A.; van Buuren, T.; Hansen, D.; Benterou, J.; May, C.; Graber, T.; Jensen, B. J.; Ilavsky, J.; Willey, T. M.

    2015-06-01

    The dynamics of carbon condensation in detonating high explosives remains controversial. Detonation model validation requires data for processes occurring at nanometer length scales on time scales ranging from nanoseconds to microseconds. A new detonation endstation has been commissioned to acquire and provide time-resolved small-angle x-ray scattering (SAXS) from detonating explosives. Hexanitrostilbene (HNS) was selected as the first to investigate due to its ease of initiation using exploding foils and flyers, vacuum compatibility, high thermal stability, and stoichiometric carbon abundance that produces high carbon condensate yields. The SAXS data during detonation, collected with 300 ns time resolution, provide unprecedented signal fidelity over a broad q-range. This fidelity permits the first analysis of both the Guinier and Porod/power-law regions of the scattering profile during detonation, which contains information about the size and morphology of the resultant carbon condensate nanoparticles. To bolster confidence in these data, the scattering angle and intensity were additionally cross-referenced with a separate, highly calibrated SAXS beamline. The data show that HNS produces carbon particles with a radius of gyration of 2.7 nm in less than 400 ns after the detonation front has passed, and this size and morphology are constant over the next several microseconds. These data directly contradict previous pioneering work on RDX/TNT mixtures and TATB, where observations indicate significant particle growth (50% or more) continues over several microseconds. The power-law slope is about -3, which is consistent with a complex disordered, irregular, or folded sp2 sub-arrangement within a relatively monodisperse structure possessing radius of gyration of 2.7 nm after the detonation of HNS.

  10. High power laser coupling to carbon nano-tubes and ion Coulomb explosion

    SciTech Connect

    K, Magesh Kumar K; Tripathi, V. K.

    2013-09-15

    Linear and non linear interaction of laser with an array of carbon nanotubes is investigated. The ac conductivity of nanotubes, due to uneven response of free electrons in them to axial and transverse fields, is a tensor. The propagation constant for p-polarization shows resonance at a specific frequency that varies with the direction of laser propagation. It also shows surface plasmon resonance at ω=ω{sub p}/√(2), where ω{sub p} is the plasma frequency of free electrons inside a nanotube, assumed to be uniform plasma cylinder. The attenuation constant is also resonantly enhanced around these frequencies. At large laser amplitude, the nanotubes behave as thin plasma rods. As the electrons get heated, the nanotubes undergo hydrodynamic expansion. At an instant when plasma frequency reaches ω{sub p}=√(2)ω, the electron temperature rises rapidly and then saturates. For a Gaussian laser beam, the heating rate is maximum on the laser axis and falls off with the distance r from the axis. When the excursion of the electrons Δ is comparable or larger than the radius of the nanotube r{sub c}, the nanotubes undergo ion Coulomb explosion. The distribution function of ions turns out to be a monotonically decreasing function of energy.

  11. Phenomenon of Energy Focusing in Explosive Systems which include High Modulus Elastic Elements

    NASA Astrophysics Data System (ADS)

    Balagansky, I.; Hokamoto, K.; Manikandan, P.; Matrosov, A.; Stadnichenko, I.; Miyoshi, H.

    2009-06-01

    The phenomenon was observed in a passive HE charge of cast Comp. B without cumulative shape under shock wave loading by explosion of an active HE charge through water after preliminary compression by a leading wave in silicon carbide insert. The phenomenon manifested itself as a hole in identification steel specimen with depth of about 10 mm and diameter of about 5 mm. Results of experiments on studying of conditions of implementation of this phenomenon for SEP and Comp. B are presented. For each HE a number of experiments has been executed at various length of silicon carbide insert. Presence or absence of a hole in the steel specimen was determined. Also a number of optical registrations of process in framing mode with record step of 1 μs have been executed. Digital video camera SHIMADZU HPV-1 was used for optical registration. Results of experiments testify that the phenomenon is reproduced both for SEP, and for Comp. B. Focusing process is observed in conditions close to critical conditions of transfer of a detonation from active to a passive HE charge.

  12. High power laser coupling to carbon nano-tubes and ion Coulomb explosion

    NASA Astrophysics Data System (ADS)

    K, Magesh Kumar K.; Tripathi, V. K.

    2013-09-01

    Linear and non linear interaction of laser with an array of carbon nanotubes is investigated. The ac conductivity of nanotubes, due to uneven response of free electrons in them to axial and transverse fields, is a tensor. The propagation constant for p-polarization shows resonance at a specific frequency that varies with the direction of laser propagation. It also shows surface plasmon resonance at ω =ωp/√2 , where ωp is the plasma frequency of free electrons inside a nanotube, assumed to be uniform plasma cylinder. The attenuation constant is also resonantly enhanced around these frequencies. At large laser amplitude, the nanotubes behave as thin plasma rods. As the electrons get heated, the nanotubes undergo hydrodynamic expansion. At an instant when plasma frequency reaches ωp=√2 ω, the electron temperature rises rapidly and then saturates. For a Gaussian laser beam, the heating rate is maximum on the laser axis and falls off with the distance r from the axis. When the excursion of the electrons Δ is comparable or larger than the radius of the nanotube rc, the nanotubes undergo ion Coulomb explosion. The distribution function of ions turns out to be a monotonically decreasing function of energy.

  13. Biological Denitrification of High Nitrate Processing Wastewaters from Explosives Production Plant.

    PubMed

    Cyplik, Paweł; Marecik, Roman; Piotrowska-Cyplik, Agnieszka; Olejnik, Anna; Drożdżyńska, Agnieszka; Chrzanowski, Lukasz

    2012-05-01

    Wastewater samples originating from an explosives production plant (3,000 mg N l(-1) nitrate, 4.8 mg l(-1) nitroglycerin, 1.9 mg l(-1) nitroglycol and 1,200 mg l(-1) chemical oxygen demand) were subjected to biological purification. An attempt to completely remove nitrate and to decrease the chemical oxygen demand was carried out under anaerobic conditions. A soil isolated microbial consortium capable of biodegrading various organic compounds and reduce nitrate to atmospheric nitrogen under anaerobic conditions was used. Complete removal of nitrates with simultaneous elimination of nitroglycerin and ethylene glycol dinitrate (nitroglycol) was achieved as a result of the conducted research. Specific nitrate reduction rate was estimated at 12.3 mg N g(-1) VSS h(-1). Toxicity of wastewater samples during the denitrification process was studied by measuring the activity of dehydrogenases in the activated sludge. Mutagenicity was determined by employing the Ames test. The maximum mutagenic activity did not exceed 0.5. The obtained results suggest that the studied wastewater samples did not exhibit mutagenic properties.

  14. High-energy particles from SN-explosions near the Galactic center

    NASA Astrophysics Data System (ADS)

    Dorfi, Ernst A.; Steiner, Daniel

    2014-05-01

    Several supernovae exploding in a compact cluster of massive stars generate a galactic outflow with embedded shock waves. Based on numerical simulations for an expanding superbubble above the Galactic center we find that these individual waves generated by the repeated SN-explosions, interact with each other and finally coalesce into a single strong shock at a distance of 5 kpc above the Galactic plane at about 5 ċ 106 years after outbreak. The resulting shock with a Mach number M ≃ 10 propagates up to 100 kpc in less than 108 years. The time-dependent mass an energy loss out of the superbubble affects the further evolution of the outflow. In such long lasting shock waves energetic particles can be accelerated above the knee of 1015 eV already near the galactic plane by a first-order Fermi-mechanism. The additional pressure gradients from such cosmic rays lead to further accelerations of the galactic outflow since these ultra-relativistic particles suffer less from adiabatic losses than the thermal gas.

  15. Equation of state formulation for unreacted solid high explosives, PETN and HMX

    NASA Astrophysics Data System (ADS)

    Nagayama, Kunihito

    2015-06-01

    Equation of state (EOS) for unreacted explosives has been formulated thermodynamically aiming at using with numerical code of SDT processes. A generalized form of EOS is given in terms of p-v-E from the available static isothermal compression curve with non-constant specific heat, and arbitrary Grüneisen volume function. In this paper, a procedure of providing p-v-E EOS is developed based on the specific heat at constant volume as a function of entropy, Grüneisen volume function, together with Birch-Murnagan form of the isotherm. Material function of EOS and shock Hugoniot for PETN and HMX has been calculated, which is compared with the experimental data of shock-particle velocity Hugoniot. Dependence of shock pressure and temperature on the Grüneisen volume function is discussed. Insensitivity of the shock-particle velocity relationship to functional form of Grüneisen volume function is also shown. Second author: Dr. Shiro Kubota (AIST Japan).

  16. Analytical Characterization of Erythritol Tetranitrate, an Improvised Explosive.

    PubMed

    Matyáš, Robert; Lyčka, Antonín; Jirásko, Robert; Jakový, Zdeněk; Maixner, Jaroslav; Mišková, Linda; Künzel, Martin

    2016-05-01

    Erythritol tetranitrate (ETN), an ester of nitric acid and erythritol, is a solid crystalline explosive with high explosive performance. Although it has never been used in any industrial or military application, it has become one of the most prepared and misused improvise explosives. In this study, several analytical techniques were explored to facilitate analysis in forensic laboratories. FTIR and Raman spectrometry measurements expand existing data and bring more detailed assignment of bands through the parallel study of erythritol [(15) N4 ] tetranitrate. In the case of powder diffraction, recently published data were verified, and (1) H, (13) C, and (15) N NMR spectra are discussed in detail. The technique of electrospray ionization tandem mass spectrometry was successfully used for the analysis of ETN. Described methods allow fast, versatile, and reliable detection or analysis of samples containing erythritol tetranitrate in forensic laboratories.

  17. DECOMMISSIONING THE HIGH PRESSURE TRITIUM LABORATORY AT LOS ALAMOS NATIONAL LABORATORY

    SciTech Connect

    Peifer, M.J.; Rendell, K.; Hearnsberger, D.W.

    2003-02-27

    In May 0f 2000, the Cerro Grande wild land fire burned approximately 48,000 acres in and around Los Alamos. In addition to the many buildings that were destroyed in the town site, many structures were also damaged and destroyed within the 43 square miles that comprise the Los Alamos National Laboratory (LANL). A special Act of Congress provided funding to remove Laboratory structures that were damaged by the fire, or that could be threatened by subsequent catastrophic wild land fires. The High Pressure Tritium Laboratory (HPTL) is located at Technical Area (TA) 33, building 86 in the far southeast corner of the Laboratory property. It is immediately adjacent to Bandelier National Park. Because it was threatened by both the Cerro Grande fire in 2000, and the 16,000- acre Dome fire in 1996, the former tritium processing facility was placed on the list of facilities scheduled for Decontamination and Decommissioning under the Cerro Grande Rehabilitation Project. The work was performed through the Facilities and Waste Operations (FWO) Division and is integrated with other Laboratory D&D efforts. The primary demolition contractor was Clauss Construction of San Diego, California. Earth Tech Global Environmental Services of San Antonio, Texas was sub-contracted to Clauss Construction, and provided radiological decontamination support to the project. Although the forty-seven year old facility had been in a state of safe-shutdown since operations ceased in 1990, a significant amount of tritium remained in the rooms where process systems were located. Tritium was the only radiological contaminant associated with this facility. Since no specific regulatory standards have been set for the release of volumetrically contaminated materials, concentration guidelines were derived in order to meet other established regulatory criteria. A tritium removal system was developed for this project with the goal of reducing the volume of tritium concentrated in the concrete of the building

  18. A Comparison of Neutron-Based Non-Destructive Assessment Methods for Chemical Warfare Materiel and High Explosives

    SciTech Connect

    E.H. Seabury; D.L. Chichester; C.J. Wharton; A.J. Caffrey

    2008-08-01

    Prompt Gamma Neutron Activation Analysis (PGNAA) systems employ neutrons as a probe to interrogate items, e.g. chemical warfare materiel-filled munitions. The choice of a neutron source in field-portable systems is determined by its ability to excite nuclei of interest, operational concerns such as radiological safety and ease-of-use, and cost. Idaho National Laboratory’s PINS Chemical Assay System has traditionally used a Cf-252 isotopic neutron source, but recently a Deuterium-Tritium (DT) Electronic Neutron Generator (ENG) has been tested as an alternate neutron source. This paper presents the results of using both of these neutron sources to interrogate chemical warfare materiel (CWM) and high explosive (HE) filled munitions.

  19. Safety Considerations for Laser Power on Metals in Contact with High Explosives-Experimental an Calculational Results

    SciTech Connect

    Roeske, F.; Carpenter, K. H.

    2000-04-19

    Measurements have been made to determine safe levels of laser exposure on common metals used in contact with high explosive (HE) samples. Laser light is often used on metals in contact with HE during alignment procedures and experimental data collection. The measurements look at temperature rise of the surface of the metal in contact with HE when laser energy is incident on the opposite side of the metal. The temperature rise was measured as a function of incident laser power, spot size, metal composition and metal thickness. Numerical simulations were also performed to solve the two-dimensional heat flow problem for the experimental geometry. In order to allow a single numerical simulation to represent a large number of physical cases, the equations used in the simulation were expressed in terms of dimensionless variables. The normalized numerical solutions can then be compared with the various experimental configurations used. Calculations and experiment agree well over the range measured.

  20. PHETS (Permanent High Explosive Test Site) lightning hardening program: Misty Picture Event. Final report, January-November 1987

    SciTech Connect

    Chapman, G.P.; Gardner, R.L.; Lu, G.S.; Rison, W.; Gurbaxani, S.H.

    1988-06-01

    The Permanent High Explosive Test Site (PHETS) test-bed electrical topology and data flow are presented along with various equipments used in the topology. Using this information, recommendations are made to harden the test-bed instrumentation to electrical transients. These transients may be caused by lightning or electrostatic discharge. Specific attention is given to the junction box design, the shorting blocks, use of shielded cables, protection of the sensors, and the instrumentation bunker/container. Additional attention is given to the protection of personnel from lightning effects. Also, it is recommended the optimum design is of a Faraday-cage concept that completely encases the instrumentation from sensor to permanent recording medium. The optimum design should be prototyped and tested using the Precision Test bed and current injection before general application to the PHETS.

  1. Proof testing of an explosion containment vessel

    SciTech Connect

    Esparza, E.D.; Stacy, H.; Wackerle, J.

    1996-10-01

    A steel containment vessel was fabricated and proof tested for use by the Los Alamos National Laboratory at their M-9 facility. The HY-100 steel vessel was designed to provide total containment for high explosives tests up to 22 lb (10 kg) of TNT equivalent. The vessel was fabricated from an 11.5-ft diameter cylindrical shell, 1.5 in thick, and 2:1 elliptical ends, 2 in thick. Prior to delivery and acceptance, three types of tests were required for proof testing the vessel: a hydrostatic pressure test, air leak tests, and two full design charge explosion tests. The hydrostatic pressure test provided an initial static check on the capacity of the vessel and functioning of the strain instrumentation. The pneumatic air leak tests were performed before, in between, and after the explosion tests. After three smaller preliminary charge tests, the full design charge weight explosion tests demonstrated that no yielding occurred in the vessel at its rated capacity. The blast pressures generated by the explosions and the dynamic response of the vessel were measured and recorded with 33 strain channels, 4 blast pressure channels, 2 gas pressure channels, and 3 displacement channels. This paper presents an overview of the test program, a short summary of the methodology used to predict the design blast loads, a brief description of the transducer locations and measurement systems, some of the hydrostatic test strain and stress results, examples of the explosion pressure and dynamic strain data, and some comparisons of the measured data with the design loads and stresses on the vessel.

  2. Infrasonic signals from an accidental chemical explosion

    SciTech Connect

    Mutschlecner, J.P.; Whitaker, R.W.

    1996-12-31

    A series of large accidental explosions occurred at a chemical plant in Henderson, Nevada on May 4, 1988. The explosions were produced by the ignition of stores of ammonium perchlorate produced for solid rocket fuel at the Pacific Engineering and Production Co. This material, prior to the incident, had been believed to be non- explosive. The blasts destroyed the plant and caused one death. There was a series of explosions over a period of time with two major explosions which we will identify as A at 18:53:34 (all times herein will be given in C.U.T.) and B at 18:57:35. Signals from events A and B as well as smaller events were detected by the infrasound arrays operated by the Los Alamos National Laboratory at St. George, Utah (distance 159 km) and at Los Alamos, N.M. (distance 774 km). The Henderson explosions present an interesting and challenging set of infrasound observations. The case may be unique in providing two very large sources separated in time by only four minutes. To fully understand the propagation details will require further analysis and probably a modeling effort. The understanding of the St. George signals in the context of Lamb waves would be valuable for a better understanding of this mode of propagation. The improved understanding of long range infrasonic propagation is now especially important in the context of the Comprehensive Test Ban Treaty (CTBT). A portion of the plan for CTBT monitoring includes a global distribution of sixty infrasound arrays to provide for the monitoring of signals in as uniform a way as possible. It is expected that under this global network many signals and interpretation questions of the type described here will be encountered. Investigations of propagation over the ranges of hundreds to thousands of kilometers will be highly desired.

  3. Report on the suitability of Class 6, U.S. government security repositories for the storage of small quantities of high explosives

    SciTech Connect

    Harry, H.H.; Murk, D.

    1998-03-01

    The Explosives Review Committee initiated a study into the safety aspects of the common practice of storing small amounts (< 10 grams per drawer) of high explosives in safes. Although storage of HE in older asbestos lined safes was permitted, the newer style Class 6 Security safes are an unacceptable repository for even very small amounts of HE without the use of a blast mitigating insert. The authors have developed a drawer liner in the form of a laminated Lexan, foam, plywood box that will withstand the blast and contain the fragments from up to 10 grams of high explosives. This liner will fit into the drawer of any existing safe. The liner will provide blast and fragment protection, and the safe will provide security protection. This report describes the testing of modern safes and the performance of the liner insert.

  4. Abiotic transformation of high explosives by freshly precipitated iron minerals in aqueous Fe¹¹ solutions

    SciTech Connect

    Boparai, Hardiljeet K.; Comfort, Steve; Satapanajaru, Tunlawit; Szecsody, James E.; Grossl, Paul; Shea, Patrick

    2010-05-11

    Zerovalent iron barriers have become a viable treatment for field-scale cleanup of various ground water contaminants. While contact with the iron surface is important for contaminant destruction, the interstitial pore water within and near the iron barrier will be laden with aqueous, adsorbed and precipitated FeII phases. These freshly precipitated iron minerals could play an important role in transforming high explosives (HE). Our objective was to determine the transformation of RDX (hexahydro-1,3,5-trinitro-1,3,5-triazine), HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine), and TNT (2,4,6-trinitrotoluene) by freshly precipitated iron FeII/FeIII minerals. This was accomplished by quantifying the effects of initial FeII concentration, pH, and the presence of aquifer solids (FeIII phases) on HE transformation rates. Results showed that at pH 8.2, freshly precipitated iron minerals transformed RDX, HMX, and TNT with reaction rates increasing with increasing FeII concentrations. RDX and HMX transformations in these solutions also increased with increasing pH (5.8-8.55). By contrast, TNT transformation was not influenced by pH (6.85-8.55) except at pH values <6.35. Transformations observed via LC/MS included a variety of nitroso products (RDX, HMX) and amino degradation products (TNT). XRD analysis identified green rust and magnetite as the dominant iron solid phases that precipitated from the aqueous FeII during HE treatment under anaerobic conditions. Geochemical modeling also predicted FeII activity would likely be controlled by green rust and magnetite. These results illustrate the important role freshly precipitated FeII/FeIII minerals in aqueous FeII solutions play in the transformation of high explosives.

  5. Detection of Explosive Materials

    NASA Astrophysics Data System (ADS)

    Trogler, William

    2008-03-01

    High explosives present a challenge for detection methods because of their range of physical properties, which range from volatile liquids to nonvolatile solids. They share the common feature of possessing both oxidizing and reducing chemical properties within a single molecule or an intimate chemical mixture. Our research group has been focused on the synthesis of new luminescent polymers, which undergo electron transfer quenching by a variety of organic high explosives, such as TNT, RDX, and PETN. The application to imaging trace explosive particle residues will be described. Density functional calculations show an excellent correlation between the sensor response and the lowest unoccupied molecular orbital of the explosive analyte. For volatile high explosives, such as organic peroxides (e.g. TATP), vapor sensors based on chemically sensitive transistors containing different metal phthalocyanines have been explored. The mechanism of current response in these films has been shown to be a result of surface Lewis acid-base chemistry or redox catalysis at the metal centers. The link between surface chemistry and electronic resonse has led to a simple peroxide specific vapor sensor array.

  6. More Interesting Than You Thought: IRIS Observations of Explosive Events

    NASA Astrophysics Data System (ADS)

    Kankelborg, C. C.; Jaeggli, S.

    2013-12-01

    Transition region explosive events (EEs) are characterized by line broadenings (to the blue or red or both) with nonthermal velocity > 100 km/s. They are widely attributed to reconnection, though their nature is still obscure and some observers have reported rotary motion. The transition region is an excellent laboratory to study reconnection in a solar context, with high emission measure in the reconnection region, a high event rate, and optically thin spectral lines. The Interface Region Imaging Spectrograph (IRIS) has observed many explosive events in Si IV and C II. We describe the substructure of supersonic flows in EEs observed by IRIS, and their morphology as revealed by IRIS slit jaw images.

  7. Explosive cord

    NASA Technical Reports Server (NTRS)

    1972-01-01

    Device, jetcord, is metal-clad linear explosive of sufficient flexibility to allow forming into intricate shapes. Total effect is termed ''cutting'' with jetcord consistently ''cutting'' a target of greater thickness than can be penetrated. Applications include sheet metal working, pipe cutting and fire-fighting.

  8. Nuclear explosions

    SciTech Connect

    Broyles, A.A.

    1982-07-01

    A summary of the physics of a nuclear bomb explosion and its effects on human beings is presented at the level of a sophomore general physics course without calculus. It is designed to supplement a standard text for such a course and problems are included.

  9. Sunset Crater, AZ: Evolution of a highly explosive basaltic eruption as indicated by granulometry and clast componentry

    NASA Astrophysics Data System (ADS)

    Allison, C. M.; Clarke, A. B.; Pioli, L.; Alfano, F.

    2011-12-01

    Basaltic scoria cone volcanoes are the most abundant volcanic edifice on Earth and occur in all tectonic settings. Basaltic magmas have lower viscosities, higher temperatures, and lower volatile contents than silicic magmas, and therefore generally have a lower potential for explosive activity. However, basaltic eruptions display great variability in eruptive style, from mild lava flows to more energetic explosions with large plumes. The San Francisco Volcanic Field (SFVF) in northern Arizona, active from 6 Ma-present, consists of over 600 volcanoes, mostly alkali basalt scoria cones, and five silicic centers [Wood and Kienle (1990), Cambridge University Press]. The eruption of Sunset Crater in the SFVF during the Holocene was an anomalously large basaltic explosive eruption, consisting of eight tephra-bearing phases and three lava flows [Amos (1986), MS thesis, ASU]. Typical scoria cone-forming eruptions have volumes <0.1km3 DRE, while the Sunset Crater deposit is at least 0.6km3 DRE [Amos (1986)]. The phases vary in size and style; the beginning stages of explosive activity (phases 1-2) were considerably smaller than phases 3-5, classified as subplinian. Due to its young age, the eruptive material is fresh and the deposit is well-preserved. We sampled the first five tephra units at 25 locations, ranging from 6 km to 20 km from the vent, concentrating our efforts in the downwind direction (E and SE of the vent) along the primary dispersal axes of several phases. Notable variations among the first five phases were found from evaluation of juvenile clast componentry, with each phase containing some proportion of red, grey, and glassy to iridescent clasts. The red and grey clasts are sub-rounded to rounded with high sphericity, while the other clasts are highly angular and slightly elongate, with blue-black to gold glassy and iridescent surfaces. The glassy and iridescent clasts likely represent fresh, juvenile ejecta, which were quenched rapidly, whereas the red and

  10. TOWARD END-TO-END MODELING FOR NUCLEAR EXPLOSION MONITORING: SIMULATION OF UNDERGROUND NUCLEAR EXPLOSIONS AND EARTHQUAKES USING HYDRODYNAMIC AND ANELASTIC SIMULATIONS, HIGH-PERFORMANCE COMPUTING AND THREE-DIMENSIONAL EARTH MODELS

    SciTech Connect

    Rodgers, A; Vorobiev, O; Petersson, A; Sjogreen, B

    2009-07-06

    This paper describes new research being performed to improve understanding of seismic waves generated by underground nuclear explosions (UNE) by using full waveform simulation, high-performance computing and three-dimensional (3D) earth models. The goal of this effort is to develop an end-to-end modeling capability to cover the range of wave propagation required for nuclear explosion monitoring (NEM) from the buried nuclear device to the seismic sensor. The goal of this work is to improve understanding of the physical basis and prediction capabilities of seismic observables for NEM including source and path-propagation effects. We are pursuing research along three main thrusts. Firstly, we are modeling the non-linear hydrodynamic response of geologic materials to underground explosions in order to better understand how source emplacement conditions impact the seismic waves that emerge from the source region and are ultimately observed hundreds or thousands of kilometers away. Empirical evidence shows that the amplitudes and frequency content of seismic waves at all distances are strongly impacted by the physical properties of the source region (e.g. density, strength, porosity). To model the near-source shock-wave motions of an UNE, we use GEODYN, an Eulerian Godunov (finite volume) code incorporating thermodynamically consistent non-linear constitutive relations, including cavity formation, yielding, porous compaction, tensile failure, bulking and damage. In order to propagate motions to seismic distances we are developing a one-way coupling method to pass motions to WPP (a Cartesian anelastic finite difference code). Preliminary investigations of UNE's in canonical materials (granite, tuff and alluvium) confirm that emplacement conditions have a strong effect on seismic amplitudes and the generation of shear waves. Specifically, we find that motions from an explosion in high-strength, low-porosity granite have high compressional wave amplitudes and weak shear

  11. Visualization of explosion phenomena using a high-speed video camera with an uncoupled objective lens by fiber-optic

    NASA Astrophysics Data System (ADS)

    Tokuoka, Nobuyuki; Miyoshi, Hitoshi; Kusano, Hideaki; Hata, Hidehiro; Hiroe, Tetsuyuki; Fujiwara, Kazuhito; Yasushi, Kondo

    2008-11-01

    Visualization of explosion phenomena is very important and essential to evaluate the performance of explosive effects. The phenomena, however, generate blast waves and fragments from cases. We must protect our visualizing equipment from any form of impact. In the tests described here, the front lens was separated from the camera head by means of a fiber-optic cable in order to be able to use the camera, a Shimadzu Hypervision HPV-1, for tests in severe blast environment, including the filming of explosions. It was possible to obtain clear images of the explosion that were not inferior to the images taken by the camera with the lens directly coupled to the camera head. It could be confirmed that this system is very useful for the visualization of dangerous events, e.g., at an explosion site, and for visualizations at angles that would be unachievable under normal circumstances.

  12. High dose calibrations at the pacific northwest laboratory

    NASA Astrophysics Data System (ADS)

    McDonald, J. C.; Fox, R. A.

    1989-04-01

    he need is increasing for both high radiation exposures and calibration measurements that provide traceability of such exposures to national standards. The applications of high exposures include: electronic component damage studies, sterilization of medical products and food irradiation. Accurate high exposure measurements are difficult to obtain and cannot, in general, be carried out with a single dose measurement system or technique because of the wide range of doses and the variety of materials involved. This paper describes the dosimetric measurement and calibration techniques used at the Pacific Northwest Laboratory (PNL) that make use of radiochromic dye films, thermoluminescence dosimeters (TLDs), ionization chambers and calorimetric dosimeters. The methods used to demonstrate the consistency of PNL calibrations with national standards will also be discussed.

  13. Apparatus for monitoring linear explosive performance

    NASA Technical Reports Server (NTRS)

    Bement, L. J.

    1974-01-01

    Techniques provide performance monitoring standard for acceptance, lot qualification, and comparison testing of devices. Exhibit high degree of simplicity, accuracy, and reproducibility. Apparatus simultaneously measures explosive pressure stimulus energy, explosive cutting, or rupturing, ability, and detonation propagation rate.

  14. Optical measurement and scaling of blasts from gram-range explosive charges

    NASA Astrophysics Data System (ADS)

    Hargather, Michael J.; Settles, Gary S.

    2007-12-01

    Laboratory-scale experiments with gram-range explosive charges are presented. Optical shadowgraphy and high-speed digital imaging are used to measure the explosive-driven shock-wave position as a function of time. From this, shock Mach number-versus-distance from the explosion center can be found. These data then yield the peak overpressure and duration, which are the key parameters in determining the potential damage from an explosion as well as the TNT equivalent of the explosive. Piezoelectric pressure gage measurements of overpressure duration at various distances from the explosive charges compare well with theoretical calculations. A scaling analysis yields an approach to relate the gram-range blast to a large-scale blast from the same or different explosives. This approach is particularly suited to determining the properties and behavior of exotic explosives like triacetone triperoxide (TATP). Results agree with previous observations that the concept of a single TNT equivalence value is inadequate to fully describe an explosive yield, rather TNT equivalence factor and overpressure duration should be presented as functions of radius.

  15. Structural biology facilities at Brookhaven National Laboratory`s high flux beam reactor

    SciTech Connect

    Korszun, Z.R.; Saxena, A.M.; Schneider, D.K.

    1994-12-31

    The techniques for determining the structure of biological molecules and larger biological assemblies depend on the extent of order in the particular system. At the High Flux Beam Reactor at the Brookhaven National Laboratory, the Biology Department operates three beam lines dedicated to biological structure studies. These beam lines span the resolution range from approximately 700{Angstrom} to approximately 1.5{Angstrom} and are designed to perform structural studies on a wide range of biological systems. Beam line H3A is dedicated to single crystal diffraction studies of macromolecules, while beam line H3B is designed to study diffraction from partially ordered systems such as biological membranes. Beam line H9B is located on the cold source and is designed for small angle scattering experiments on oligomeric biological systems.

  16. Ford Research Laboratory high school science and technology program (HSSTP)

    SciTech Connect

    Hass, K.C.

    1994-12-31

    Since 1984, the Ford Motor Company Research Laboratory has offered a series of Saturday morning enrichment experiences and summer work opportunities for high school students and teachers. The goal is to increase awareness of technical careers and the importance of science and mathematics in industry. The Saturday sessions are run entirely by volunteers and are organized around current topics ranging from fundamental science (e.g., atmospheric chemistry) to advanced engineering and manufacturing (e.g., glass production). A typical session includes a lecture, laboratory tours and demonstrations, a refreshment/social break and a hands-on activity whenever possible. Over 500 students and teachers participate annually from over 120 area high schools. Nearly one third of the students are minorities from the city of Detroit. Session quality is monitored through feedback from participants and volunteers. Juniors and seniors who attend at least three sessions are eligible to compete for four-week summer internships. Typically, about twenty-five to thirty interns (out of forty to fifty applicants) are selected on the basis of a transcript, teacher recommendation and a 2500-word report on a technical topic. Ford also generally hosts about eight summer teacher fellows through a statewide program that began as an HSSTP initiative. The HSSTP was recently recognized by the industrial Research Institute as one of eleven {open_quotes}Winning [Pre-College Education] Programs{close_quotes} nationwide. Keys to success include strong grassroots and managerial support and extensive networking in the community.

  17. The High Flux Beam Reactor at Brookhaven National Laboratory

    SciTech Connect

    Shapiro, S.M.

    1994-12-31

    Brookhaven National Laboratory`s High Flux Beam Reactor (HFBR) was built because of the need of the scientist to always want `more`. In the mid-50`s the Brookhaven Graphite reactor was churning away producing a number of new results when the current generation of scientists, led by Donald Hughes, realized the need for a high flux reactor and started down the political, scientific and engineering path that led to the BFBR. The effort was joined by a number of engineers and scientists among them, Chemick, Hastings, Kouts, and Hendrie, who came up with the novel design of the HFBR. The two innovative features that have been incorporated in nearly all other research reactors built since are: (i) an under moderated core arrangement which enables the thermal flux to peak outside the core region where beam tubes can be placed, and (ii) beam tubes that are tangential to the core which decrease the fast neutron background without affecting the thermal beam intensity. Construction began in the fall of 1961 and four years later, at a cost of $12 Million, criticality was achieved on Halloween Night, 1965. Thus began 30 years of scientific accomplishments.

  18. Explosion containment device

    DOEpatents

    Benedick, William B.; Daniel, Charles J.

    1977-01-01

    The disclosure relates to an explosives storage container for absorbing and containing the blast, fragments and detonation products from a possible detonation of a contained explosive. The container comprises a layer of distended material having sufficient thickness to convert a portion of the kinetic energy of the explosion into thermal energy therein. A continuous wall of steel sufficiently thick to absorb most of the remaining kinetic energy by stretching and expanding, thereby reducing the momentum of detonation products and high velocity fragments, surrounds the layer of distended material. A crushable layer surrounds the continuous steel wall and accommodates the stretching and expanding thereof, transmitting a moderate load to the outer enclosure. These layers reduce the forces of the explosion and the momentum of the products thereof to zero. The outer enclosure comprises a continuous pressure wall enclosing all of the layers. In one embodiment, detonation of the contained explosive causes the outer enclosure to expand which indicates to a visual observer that a detonation has occurred.

  19. Luminescent metal-organic framework-functionalized graphene oxide nanocomposites and the reversible detection of high explosives

    NASA Astrophysics Data System (ADS)

    Lee, Ji Ha; Jaworski, Justyn; Jung, Jong Hwa

    2013-08-01

    Achieving both high specificity and sensitivity are essential for gas phase chemical detection systems. Recent implementation of Metal-Organic Frameworks (MOFs) have shown great success in separation and storage systems for specific gas molecules. By implementing a MOF structure comprised of Zn2+ coordinated trans-stilbene derivatives, a gas responsive material has been created which exhibits a high photoluminescence quantum yield, offering new opportunities for chemical sensors. Here, we reveal a nanocomposite material, assembled from azobenzene functionalized graphene oxide and stilbene-MOF, that is capable of luminescent quenching by explosive gases. This unique system displays selectivity to dinitrotoluene (71% quenching) over trinitrotoluene (20% quenching) with sub ppm sensitivity and response times of less than a minute. We show that this implementation of a graphene-based MOF composite provides a unique strategy in the development of molecularly well-defined materials having rapid, reversible, and gas selective fluorescent quenching capabilities. This opens the way for new advances in the assembly of low density frameworks using isomerization suppressed materials.Achieving both high specificity and sensitivity are essential for gas phase chemical detection systems. Recent implementation of Metal-Organic Frameworks (MOFs) have shown great success in separation and storage systems for specific gas molecules. By implementing a MOF structure comprised of Zn2+ coordinated trans-stilbene derivatives, a gas responsive material has been created which exhibits a high photoluminescence quantum yield, offering new opportunities for chemical sensors. Here, we reveal a nanocomposite material, assembled from azobenzene functionalized graphene oxide and stilbene-MOF, that is capable of luminescent quenching by explosive gases. This unique system displays selectivity to dinitrotoluene (71% quenching) over trinitrotoluene (20% quenching) with sub ppm sensitivity and

  20. Dynamic Measurements of High Explosive Velocity Fields using Particle Image Velocimetry

    NASA Astrophysics Data System (ADS)

    Wilson, Brandon; Wood, Wm. M.; Olson, Russ

    2015-06-01

    A non-invasive technique for measuring dynamic particle velocities using pRad images ahead and behind an HE detonation burn front is presented. The technique uses proven principles from particle image velocimetry (PIV). Time-resolved radiographs of detonated HE (PBX 9501 and 9502) doped with tungsten particles (<= 10 μ m) are captured at pRad at Los Alamos National Laboratory. From sequential radiographs, resolved velocity fields are measured by local cross-correlations of tungsten tracer positions. With this technique, we resolve the Taylor wave and can measure the particle velocity directly behind the detonation front. Results for single detonation waves and colliding detonation waves are presented. We also discuss the capabilities, limitations, applications, and future of this technique.

  1. Explosive Joining

    NASA Technical Reports Server (NTRS)

    1989-01-01

    Laurence J. Bement of Langley Research Center invented a technique to permit metal joining operations under hazardous or inaccessible conditions. The process, which provides a joint with double the strength of the parent metal, involves the use of very small quantities of ribbon explosive to create hermetically sealed joints. When the metal plates are slammed together by the explosion's force, joining is accomplished. The collision causes a skin deep melt and ejection of oxide films on the surfaces, allowing a linkup of electrons that produce superstrong, uniform joints. The technique can be used to join metals that otherwise would not join and offers advantages over mechanical fasteners and adhesives. With Langley assistance, Demex International Ltd. refined and commercialized the technology. Applications include plugging leaking tubes in feedwater heaters. Demex produces the small plugs, associated sleeves and detonators. The technology allows faster plugging, reduces downtime, cuts plugging costs and increases reliability.

  2. Brontides: natural explosive noises.

    PubMed

    Gold, T; Soter, S

    1979-04-27

    Episodes of explosive noises of natural origin, or brontides, have been well documented, often in association with seismic activity and in a few cases as precursors to major earthquakes. Ground-to-air acoustic transmission from shallow earthquakes can account for many of these episodes, but not for all, and other causes, such as the sudden eruption of gas from high-pressure sources in the ground may at times have been responsible. Confusion with distant thunder or artillery at times of anomalous sound propagation complicates the analysis, and more recently the greatly increased frequency of artificial explosive noises and sonic booms has tended to mask the recognition of natural brontides. PMID:17757998

  3. Continuous steam explosion

    SciTech Connect

    Taylor, J.D.; Yu, E.K.C.

    1995-02-01

    StakeTech has focused on developing steam explosion on a commercial basis. The company essentially a biomass conversion company dealing with cellulosic biomass such as wood, crop residues and, more recently, wastepaper and municipal solid waste (MSW). They are faced with a tremendous opportunity to develop uses for the 50% of biomass that is currently wasted. The StakeTech steam explosion process is able to break the bonds using only high-pressure steam with no chemical additives. The continuous StakeTech System now has been installed in five countries and has proved effective in processing a wide variety of raw materials including wood chips, straw, sugarcane bagasse, and waste paper. End-use applications range from specialty chemicals to large-volume agricultural products. The increase of development activities in steam explosion should lead to expanded end-use applications, and acceptance of the technology by industry should accelerate in the years to come.

  4. Boosting laboratory photoelectron spectroscopy by megahertz high-order harmonics

    NASA Astrophysics Data System (ADS)

    Chiang, Cheng-Tien; Huth, Michael; Trützschler, Andreas; Kiel, Mario; Schumann, Frank O.; Kirschner, Jürgen; Widdra, Wolf

    2015-01-01

    Since the discovery of the photoelectric effect, photoelectron spectroscopy has evolved into the most powerful technique for studying the electronic structure of materials. Moreover, the recent combination of photoelectron experiments with attosecond light sources using high-order harmonic generation (HHG) allows direct observation of electron dynamics in real time. However, the efficiency of these experiments is greatly limited by space-charge effects at typically low repetition rates of photoexcitation. Here, we demonstrate HHG-based laboratory photoemission experiments at a photoelectron count rate of 1 × 105 electrons/s and characterize the main features of the electronic band structure of Ag(001) within several seconds without significant degradation by the space-charge effects. The combination of a compact HHG light source at megahertz repetition rates with the efficient collection of photoelectrons using time-of-flight spectroscopy may allow rapid investigation of electronic bands in a flexible laboratory environment and pave the way for an efficient design of attosecond spectroscopy and microscopy.

  5. Trace Explosive Detection Using Nanosensors

    SciTech Connect

    Senesac, Larry R; Thundat, Thomas George

    2008-01-01

    Selective and sensitive detection of explosives is very important in countering terrorist threats. Detecting trace explosives has become a very complex and expensive endeavor because of a number of factors, such as the wide variety of materials that can be used as explosives, the lack of easily detectable signatures, the vast number of avenues by which these weapons can be deployed, and the lack of inexpensive sensors with high sensitivity and selectivity. High sensitivity and selectivity, combined with the ability to lower the deployment cost of sensors using mass production, is essential in winning the war on explosives-based terrorism. Nanosensors have the potential to satisfy all the requirements for an effective platform for the trace detection of explosives.

  6. High incidence of micronuclei in lymphocytes from residents of the area near the Semipalatinsk nuclear explosion test site.

    PubMed

    Tanaka, K; Tchaijunusova, N J; Takatsuji, T; Gusev, B I; Sakerbaev, A K; Hoshi, M; Kamada, N

    2000-03-01

    The Semipalatinsk area is highly contaminated with radioactive fallout from 40 years of continuous nuclear testing. The biological effects on human health in this area have not been studied. Significant remaining radioactivities include long-lived radioisotopes of 238,239,400Pu, 137Cs and 90Sr. To evaluate the long-term biological effects of the radioactive fallout, the incidence of micronuclei in lymphocytes from residents of the area was observed. Blood was obtained from 10 residents (5 females and 5 males, aged 47 to 55 years old) from each of the 3 areas of Znamenka, Dolon and Semipalatinsk, which are about 50-150 km from the nuclear explosion test site. For micronucleus assay, PHA-stimulated lymphocytes were cultured for 72 h and cytochalasin B was added at 44 h for detecting binuclear lymphocytes. Five thousand binuclear lymphocytes in each resident were scored. The means of micronucleus counts in 1,000 lymphocytes in residents of Semipalatinsk, Dolon and Znamenka were 16.3, 12.6, and 7.80, respectively, which were higher than those of the normal Japanese persons (4.66). These values were equivalent to the results obtained from 0.187-0.47 Gy of chronic exposure to gamma-rays at a dose rate of 0.02 cGy/min. The high incidence of micronuclei in residents of the Semipalatinsk nuclear test site area was mainly caused by internal exposure rather than external exposure received for the past 40 years.

  7. A Model-Based Signal Processing Approach to Nuclear Explosion Monitoring

    SciTech Connect

    Rodgers, A; Harris, D; Pasyanos, M

    2007-03-14

    This report describes research performed under Laboratory Research and Development Project 05-ERD-019, entitled ''A New Capability for Regional High-Frequency Seismic Wave Simulation in Realistic Three-Dimensional Earth Models to Improve Nuclear Explosion Monitoring''. A more appropriate title for this project is ''A Model-Based Signal Processing Approach to Nuclear Explosion Monitoring''. This project supported research for a radically new approach to nuclear explosion monitoring as well as allowed the development new capabilities in computational seismology that can contribute to NNSA/NA-22 Programs.

  8. Development of a trace explosives detection portal for personnel screening

    SciTech Connect

    Parmeter, J.E.; Linker, K.L.; Rhykerd, C.L. Jr.; Bouchier, F.A.; Hannum, D.W.

    1998-08-01

    The authors discuss the development, design, and operation of a walk-through trace detection portal designed to screen personnel for explosives. Developed at Sandia National Laboratories (SNL) with primary funding from the Federal Aviation Administration (FAA) and additional support from the Department of Energy office of Safeguards and Security, this portal is intended primarily for use in airport terminals and in other localities where a very high throughput of pedestrian traffic is combined with stringent security requirements. The portal is capable of detecting both vapor and particulate contamination, with the collection of explosive material being based upon the entrainment of that material in air flows over the body of the person being screened. This portal is capable of detecting most types of common high explosives of interest to the FAA. The authors discuss the results of field testing of the portal in the Albuquerque International Airport in September, 1997 and more recent steps towards commercialization of the portal.

  9. Publications resulting from the fundamental research on explosives program

    SciTech Connect

    Rivera, T.

    1998-04-01

    The five-year Fundamental Research on Explosives Program at Los Alamos National Laboratory, begun in 1981, was the study of explosives behavior at a molecular level. The research team developed and tested a model of a simple explosive, liquid nitric oxide (NO), overcoming difficult problems to investigate its properties. Using recently developed high-speed technology, the authors conducted innovative experiments, such as those on high-density NO, on the molecular spectroscopy of shock-compressed materials, and on detonating liquid NO. They developed methods for calculating the thermodynamics of dense molecular systems and describing molecular-level chemistry. The team obtained theoretical and experimental equations of state for the products of detonating liquid NO and obtained the first coherent anti-Stokes Raman spectroscopy data in shock-compressed materials. The program created worldwide enthusiasm in detonation and shock wave physics and chemistry; the bibliography included in this report is the result of numerous requests for the results.

  10. Integrating Laboratory Activity into a Junior High School Classroom

    ERIC Educational Resources Information Center

    Shyr, Wen-Jye

    2010-01-01

    This paper presents a wind power system laboratory activity and an outline for evaluating student performance in this activity. The work described here was to design and implement the laboratory to assist teachers in achieving the teaching objective of this activity. The laboratory teaching activities introduce energy sources, wind energy…

  11. Method for fabricating non-detonable explosive simulants

    DOEpatents

    Simpson, Randall L.; Pruneda, Cesar O.

    1995-01-01

    A simulator which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules.

  12. Method for fabricating non-detonable explosive simulants

    DOEpatents

    Simpson, R.L.; Pruneda, C.O.

    1995-05-09

    A simulator is disclosed which is chemically equivalent to an explosive, but is not detonable. The simulator has particular use in the training of explosives detecting dogs and calibrating sensitive analytical instruments. The explosive simulants may be fabricated by different techniques, a first involves the use of standard slurry coatings to produce a material with a very high binder to explosive ratio without masking the explosive vapor, and the second involves coating inert beads with thin layers of explosive molecules. 5 figs.

  13. Infrared Spectroscopy of Explosives Residues: Measurement Techniques and Spectral Analysis

    SciTech Connect

    Phillips, Mark C.; Bernacki, Bruce E.

    2015-03-11

    Infrared laser spectroscopy of explosives is a promising technique for standoff and non-contact detection applications. However, the interpretation of spectra obtained in typical standoff measurement configurations presents numerous challenges. Understanding the variability in observed spectra from explosives residues and particles is crucial for design and implementation of detection algorithms with high detection confidence and low false alarm probability. We discuss a series of infrared spectroscopic techniques applied toward measuring and interpreting the reflectance spectra obtained from explosives particles and residues. These techniques utilize the high spectral radiance, broad tuning range, rapid wavelength tuning, high scan reproducibility, and low noise of an external cavity quantum cascade laser (ECQCL) system developed at Pacific Northwest National Laboratory. The ECQCL source permits measurements in configurations which would be either impractical or overly time-consuming with broadband, incoherent infrared sources, and enables a combination of rapid measurement speed and high detection sensitivity. The spectroscopic methods employed include standoff hyperspectral reflectance imaging, quantitative measurements of diffuse reflectance spectra, reflection-absorption infrared spectroscopy, microscopic imaging and spectroscopy, and nano-scale imaging and spectroscopy. Measurements of explosives particles and residues reveal important factors affecting observed reflectance spectra, including measurement geometry, substrate on which the explosives are deposited, and morphological effects such as particle shape, size, orientation, and crystal structure.

  14. Explosive simulants for testing explosive detection systems

    DOEpatents

    Kury, John W.; Anderson, Brian L.

    1999-09-28

    Explosives simulants that include non-explosive components are disclosed that facilitate testing of equipment designed to remotely detect explosives. The simulants are non-explosive, non-hazardous materials that can be safely handled without any significant precautions. The simulants imitate real explosives in terms of mass density, effective atomic number, x-ray transmission properties, and physical form, including moldable plastics and emulsions/gels.

  15. Sandia National Laboratories' new high level acoustic test facility

    SciTech Connect

    Rogers, J. D.; Hendrick, D. M.

    1989-01-01

    A high intensity acoustic test facility has been designed and is under construction at Sandia National Laboratories in Albuquerque, NM. The chamber is designed to provide an acoustic environment of 154dB (re 20 {mu}Pa) overall sound pressure level over the bandwidth of 50 Hz to 10,000 Hz. The chamber has a volume of 16,000 cubic feet with interior dimensions of 21.6 ft {times} 24.6 ft {times} 30 ft. The construction of the chamber should be complete by the summer of 1990. This paper discusses the design goals and constraints of the facility. The construction characteristics are discussed in detail, as are the acoustic performance design characteristics. The authors hope that this work will help others in designing acoustic chambers. 12 refs., 6 figs.

  16. Helium recovery at the National High Magnetic Field Laboratory

    NASA Astrophysics Data System (ADS)

    Barrios, M.; Kynoch, J.

    2015-12-01

    Helium conservation is becoming increasingly important as helium availability is on the decline and prices are on the rise. The Florida State University National High Magnetic Field Laboratory has taken several steps over the past five years to increase the percentage of helium recovered. These include the installation of a standalone purifier, recovery flow meters, contamination meters, and a new piping system. The improvements to the recovery system have reduced the amount of helium purchased by the Mag Lab by 60% while helium usage has increased by roughly 40%. This article will provide details about the recovery system as a whole and describe some of the main components. There will also be some examples of the problems we've had to overcome, and some that we are still working on. Finally, there will be an update on the current status of the recovery system and a description of our plans for the future.

  17. NATIONAL HIGH MAGENTIC FIELD LABORATORY FEL INJECTOR DESIGN CONSIDERATION

    SciTech Connect

    Pavel Evtushenko; Stephen Benson; David Douglas; George Neil

    2007-06-25

    A Numerical study of beam dynamics was performed for two injector systems for the proposed National High Magnetic Field Laboratory at the Florida State University (FSU) Free Electron Laser (FEL) facility. The first considered a system consisting of a thermionic DC gun, two buncher cavities operated at 260 MHz and 1.3 GHz and two TESLA type cavities, and is very similar to the injector of the ELBE Radiation Source. The second system we studied uses a DC photogun (a copy of JLab FEL electron gun), one buncher cavity operated at 1.3 GHz and two TESLA type cavities. The study is based on PARMELA simulations and takes into account operational experience of both the JLab FEL and the Radiation Source ELBE. The simulations predict the second system will have a much smaller longitudinal emittance. For this reason the DC photo gun based injector is preferred for the proposed FSU FEL facility.

  18. A laboratory study of spray generation in high winds

    NASA Astrophysics Data System (ADS)

    Ortiz-Suslow, D. G.; Haus, B. K.; Mehta, S.; Laxague, N. J. M.

    2016-05-01

    Characterizing the vertical distribution of large spray particles (i.e., spume) in high wind conditions is necessary for better understanding of the development of the atmospheric boundary layer in extreme conditions. To this end a laboratory experiment was designed to observe the droplet concentration in the air above actively breaking waves. The experiments were carried out in hurricane force conditions (U 10 equivalent wind speed of 36 to 54 m/s) and using both fresh water and salt water. While small differences between fresh and salt water were observed in profiles of radius-integrated spray volume fraction, the profiles tend to converge as the wind forcing increases. This supports the assumption that the physical mechanism for spume production is not sensitive to salinity and its corresponding link to the bubble size distribution.

  19. Thermally stable, plastic-bonded explosives

    DOEpatents

    Benziger, Theodore M.

    1979-01-01

    By use of an appropriate thermoplastic rubber as the binder, the thermal stability and thermal stress characteristics of plastic-bonded explosives may be greatly improved. In particular, an HMX-based explosive composition using an oil-extended styrene-ethylenebutylene-styrene block copolymer as the binder exhibits high explosive energy and thermal stability and good handling safety and physical properties.

  20. Doping explosive materials for neutron radiographic enhancement.

    NASA Technical Reports Server (NTRS)

    Golliher, K. G.

    1971-01-01

    Discussion of studies relating to the selection of doping materials of high neutron absorption usable for enhancing the neutron radiographic imaging of explosive mixtures, without interfering with the proper chemical reaction of the explosives. The results of the studies show that gadolinium oxide is an excellent material for doping explosive mixtures to enhance the neutron radiographic image.

  1. Analysis of Picattiny Sample for Trace Explosives

    SciTech Connect

    Klunder, G; Whipple, R; Carman, L; Spackman, P E; Reynolds, J; Alcaraz, A

    2008-05-23

    The sample received from Picatinny Arsenal was analyzed for trace amounts of high explosives (HE). A complete wash of the surface was performed, concentrated, and analyzed using two sensitive analysis techniques that are capable of detecting numerous types of explosives. No explosives were detected with either test.

  2. Explosive performance measurements on large, multiple-hole arrays and large masses of conventional explosive

    SciTech Connect

    McKown, T.O.; Eilers, D.D.; Williams, P.E.

    1995-12-31

    The COntinuous Reflectometry for Radius vs. Time EXperiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation. In 1979, the CORRTEX system was shown to be ideally suited for chemical explosive performance measurements. Its utility for diagnosing chemical explosives was further demonstrated with successful measurements on large multiple-hole chemical shots in rock quarries and strip mines. Accurate timing of the detonation of sequenced or ripple fired arrays, as well as data characterizing the initiation, explosive performance and detonation anomalies are obtained. This information can serve as the basis for empirical or modeled improvements to blasting operations. A summary of the special CORRTEX features and well developed analysis techniques together with the experiment designs, data, and conclusions regarding the measurements and explosive performance from several array detonations and the Chemical Kiloton Experiment, 2.9 million pounds of an ammonium nitrate-fuel oil (ANFO) and emulsion blend conducted on the Nevada Test Site in 1993, are presented.

  3. Explosive performance measurements on large, multiple-hole arrays and large masses of conventional explosive

    SciTech Connect

    McKown, T.O.; Eilers, D.D.; Williams, P.E.

    1994-11-01

    The COntinuous Reflectometry for Radius vs. Time EXperiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation. In 1979, the CORRTEX system was shown to be ideally suited for chemical explosive performance measurements. Its utility for diagnosing chemical explosives was further demonstrated with successful measurements on large multiple-hole chemical shots in rock quarries and strip mines. Accurate timing of the detonation of sequenced or ripple fired arrays, as well as data characterizing the initiation, explosive performance and detonation anomalies are obtained. This information can serve as the basis for empirical or modeled improvements to blasting operations. A summary of the special CORRTEX features and well developed analysis techniques together with the experiment designs, data, and conclusions regarding the measurements and explosive performance from several array detonations and the Chemical Kiloton Experiment, 2.9 million pounds of an ammonium nitrate-fuel oil (ANFO) and emulsion blend conducted on the Nevada Test Site in 1993, are presented.

  4. Determination of Nanogram Microparticles from Explosives after Real Open-Air Explosions by Confocal Raman Microscopy.

    PubMed

    Zapata, Félix; García-Ruiz, Carmen

    2016-07-01

    Explosives are increasingly being used for terrorist attacks to cause devastating explosions. The detection of their postblast residues after an explosion is a high challenge, which has been barely investigated, particularly using spectroscopic techniques. In this research, a novel methodology using confocal Raman microscopy has been developed for the analysis of postblast residues from 10 open-air explosions caused by 10 different explosives (TNT, RDX, PETN, TATP, HMTD, dynamite, black powder, ANFO, chloratite, and ammonal) commonly used in improvised explosive devices. The methodology for the determination of postblast particles from explosives consisted of examining the samples surfaces with both the naked eye, first, and microscopically (10× and 50×), immediately afterward; and finally, analyzing the selected residues by confocal Raman spectroscopy in order to identify the postblast particles from explosives. Interestingly, confocal Raman microscopy has demonstrated to be highly suitable to rapidly, selectively, and noninvasively analyze postblast microscopic particles from explosives up to the nanogram range. PMID:27281604

  5. Determination of Nanogram Microparticles from Explosives after Real Open-Air Explosions by Confocal Raman Microscopy.

    PubMed

    Zapata, Félix; García-Ruiz, Carmen

    2016-07-01

    Explosives are increasingly being used for terrorist attacks to cause devastating explosions. The detection of their postblast residues after an explosion is a high challenge, which has been barely investigated, particularly using spectroscopic techniques. In this research, a novel methodology using confocal Raman microscopy has been developed for the analysis of postblast residues from 10 open-air explosions caused by 10 different explosives (TNT, RDX, PETN, TATP, HMTD, dynamite, black powder, ANFO, chloratite, and ammonal) commonly used in improvised explosive devices. The methodology for the determination of postblast particles from explosives consisted of examining the samples surfaces with both the naked eye, first, and microscopically (10× and 50×), immediately afterward; and finally, analyzing the selected residues by confocal Raman spectroscopy in order to identify the postblast particles from explosives. Interestingly, confocal Raman microscopy has demonstrated to be highly suitable to rapidly, selectively, and noninvasively analyze postblast microscopic particles from explosives up to the nanogram range.

  6. Laboratory for Nuclear Science. High Energy Physics Program

    SciTech Connect

    Milner, Richard

    2014-07-30

    High energy and nuclear physics research at MIT is conducted within the Laboratory for Nuclear Science (LNS). Almost half of the faculty in the MIT Physics Department carry out research in LNS at the theoretical and experimental frontiers of subatomic physics. Since 2004, the U.S. Department of Energy has funded the high energy physics research program through grant DE-FG02-05ER41360 (other grants and cooperative agreements provided decades of support prior to 2004). The Director of LNS serves as PI. The grant supports the research of four groups within LNS as “tasks” within the umbrella grant. Brief descriptions of each group are given here. A more detailed report from each task follows in later sections. Although grant DE-FG02-05ER41360 has ended, DOE continues to fund LNS high energy physics research through five separate grants (a research grant for each of the four groups, as well as a grant for AMS Operations). We are pleased to continue this longstanding partnership.

  7. High aspect ratio micro-explosions in the bulk of sapphire generated by femtosecond Bessel beams

    PubMed Central

    Rapp, L.; Meyer, R.; Giust, R.; Furfaro, L.; Jacquot, M.; Lacourt, P. A.; Dudley, J. M.; Courvoisier, F.

    2016-01-01

    Femtosecond pulses provide an extreme degree of confinement of light matter-interactions in high-bandgap materials because of the nonlinear nature of ionization. It was recognized very early on that a highly focused single pulse of only nanojoule energy could generate spherical voids in fused silica and sapphire crystal as the nanometric scale plasma generated has energy sufficient to compress the material around it and to generate new material phases. But the volumes of the nanometric void and of the compressed material are extremely small. Here we use single femtosecond pulses shaped into high-angle Bessel beams at microjoule energy, allowing for the creation of very high 100:1 aspect ratio voids in sapphire crystal, which is one of the hardest materials, twice as dense as glass. The void volume is 2 orders of magnitude higher than those created with Gaussian beams. Femtosecond and picosecond illumination regimes yield qualitatively different damage morphologies. These results open novel perspectives for laser processing and new materials synthesis by laser-induced compression. PMID:27669676

  8. Optical detection of explosives: spectral signatures for the explosive bouquet

    NASA Astrophysics Data System (ADS)

    Osborn, Tabetha; Kaimal, Sindhu; Causey, Jason; Burns, William; Reeve, Scott

    2009-05-01

    Research with canines suggests that sniffer dogs alert not on the odor from a pure explosive, but rather on a set of far more volatile species present in an explosive as impurities. Following the explosive trained canine example, we have begun examining the vapor signatures for many of these volatile impurities utilizing high resolution spectroscopic techniques in several molecular fingerprint regions. Here we will describe some of these high resolution measurements and discuss strategies for selecting useful spectral signature regions for individual molecular markers of interest.

  9. Evidence for phase-explosion and generation of large particles during high power nanosecond laser ablation of silicon

    SciTech Connect

    Yoo, J. H.; Jeong, S. H.; Mao, X. L.; Greif, R.; Russo, R. E.

    2000-02-07

    The craters resulting from high-irradiance (1x10{sup 9}-1x10{sup 11} W/cm{sup 2}) single-pulse laser ablation of single-crystal silicon show a dramatic increase in volume at a threshold irradiance of 2.2x10{sup 10} W/CM{sup 2}. Time-resolved shadowgraph images show ejection of large particulates from the sample above this threshold irradiance, with a time delay {approx}300 ns. A numerical model was used to estimate the thickness of a superheated layer near the critical state. Considering the transformation of liquid metal into liquid dielectric near the critical state (i.e., induced transparency), the calculated thickness of the superheated layer at a delay time of 200-300 ns agreed with the measured crater depths. This agreement suggests that induced transparency promotes the formation of a deep superheated layer, and explosive boiling within this layer leads to particulate ejection from the sample. (c) 2000 American Institute of Physics.

  10. A flow integrated DSD hydrodynamics strategy for computing the motion of detonation of insensitive high explosives on an Eulerian grid

    SciTech Connect

    Short, Mark; Aslam, Tariq D

    2010-01-01

    The detonation structure in many insensitive high explosives consists of two temporally disparate zones of heat release. In PBX 9502, there is a fast reaction zone ({approx} 25 ns) during which reactants are converted to gaseous products and small carbon clusters, followed by a slower regime ({approx} 250 ns) of carbon coagulation. A hybrid approach for determining the propagation of two-stage heat release detonations has been developed that utilizes a detonation shock dynamics (DSD) based strategy for the fast reaction zone with a direct hydrodynamic simulation of the flow in the slow zone. Unlike a standard DSD/programmed bum formulation, the evolution of the fast zone DSD-like surface is coupled to the flow in the slow reaction zone. We have termed this formulation flow integrated detonation shock dynamics (FIDSD). The purpose of the present paper is to show how the FIDSD formulation can be applied to detonation propagation on an Eulerian grid using an algorithm based on level set interface tracking and a ghost fluid approach.

  11. In-situ monitoring of flow-permeable surface area of high explosive powder using small sample masses

    SciTech Connect

    Maiti, Amitesh; Han, Yong; Zaka, Fowzia; Gee, Richard H.

    2015-02-17

    To ensure good performance of high explosive devices over long periods of time, initiating powders need to maintain their specific surface area within allowed margins during the entire duration of deployment. A common diagnostic used in this context is the Fisher sub-sieve surface area (FSSA). Furthermore, commercial permeametry instruments measuring the FSSA requires the utilization of a sample mass equal to the crystal density of the sample material, an amount that is often one or two orders of magnitude larger than the typical masses found in standard detonator applications. Here we develop a customization of the standard device that can utilize just tens of milligram samples, and with simple calibration yield FSSA values at ac curacy levels comparable to the standard apparatus. This necessitated a newly designed sample holder, made from a material of low coefficient of thermal expansion, which is conveniently transferred between an aging chamber and a re-designed permeametry tube. This improves the fidelity of accelerated aging studies by allowing measurement on the same physical sample at various time - instants during the aging process, and by obviating the need for a potentially FSSA-altering powder re-compaction step. We used the customized apparatus to monitor the FSSA evolution of a number of undoped and homolog-doped PETN powder samples that were subjected to artificial aging for several months at elevated temperatures. These results, in conjunction with an Arrhenius-based aging model were used to assess powder-coarsening - rates under long-term storage.

  12. A Method of Highly Sensitive Detecting of Explosives on the Basis of FAIMS Analyzer with Laser Ion Source

    NASA Astrophysics Data System (ADS)

    Chistyakov, A. A.; Kotkovskii, G. E.; Odulo, I. P.; Spitsyn, E. M.; Shestakov, A. V.

    In this work comparison of the desorption effectiveness of picosecond and nanosecond laser sources (λ=266, 532 nm) were carried out to investigate the possibility of creating a non-contact sampling device for detectors of explosives on the principles of ion mobility spectrometry (IMS) and field asymmetric ion mobility spectrometry (FAIMS). The results of mass spectrometric studies of TNT (2,4,6-Trinitrotoluene), HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine), RDX (1,3,5-Trinitro-1,3,5-triazacyclohexane) laser desorption from a quartz substrate are presented. It is shown that the most effective laser source is a Nd:YAG3+ laser (λ = 266 nm; E = 1 mJ; τ = 5-10 ns; q = 108 W/cm2). The typical desorbed mass is 2 ng for RDX, 4-6 ng for TNT and 0.02 ng HMX per single laser pulse. The results obtained make it possible to create a non-contact portable laser sampling device operating in frequency mode with high efficiency.

  13. Multiyear Program Plan for the High Temperature Materials Laboratory

    SciTech Connect

    Arvid E. Pasto

    2000-03-17

    Recently, the U.S. Department of Energy's (DOE) Office of Heavy Vehicle Technologies (OHVT) prepared a Technology Roadmap describing the challenges facing development of higher fuel efficiency, less polluting sport utility vehicles, vans, and commercial trucks. Based on this roadmap, a multiyear program plan (MYPP) was also developed, in which approaches to solving the numerous challenges are enumerated. Additional planning has been performed by DOE and national laboratory staff, on approaches to solving the numerous challenges faced by heavy vehicle system improvements. Workshops and planning documents have been developed concerning advanced aerodynamics, frictional and other parasitic losses, and thermal management. Similarly, the Heavy Vehicle Propulsion Materials Program has developed its own multiyear program plan. The High Temperature Materials Laboratory, a major user facility sponsored by OHVT, has now developed its program plan, described herein. Information was gathered via participation in the development of OHVT's overall Technology Roadmap and MYPP, through personal contacts within the materials-user community, and from attendance at conferences and expositions. Major materials issues for the heavy vehicle industry currently center on trying to increase efficiency of (diesel) engines while at the same time reducing emissions (particularly NO{sub x} and particulates). These requirements dictate the use of increasingly stronger, higher-temperature capable and more corrosion-resistant materials of construction, as well as advanced catalysts, particulate traps, and other pollution-control devices. Exhaust gas recirculation (EGR) is a technique which will certainly be applied to diesel engines in the near future, and its use represents a formidable challenge, as will be described later. Energy-efficient, low cost materials processing methods and surface treatments to improve wear, fracture, and corrosion resistance are also required.

  14. Detonation wave profiles in HMX based explosives

    SciTech Connect

    Gustavsen, R.L.; Sheffield, S.A.; Alcon, R.R.

    1997-11-01

    Detonation wave profiles have been measured in several HMX based plastic bonded explosives including PBX9404, PBX9501, and EDC-37, as well as two HMX powders (coarse and fine) pressed to 65% of crystal density. The powders had 120 and 10 {micro}m average grain sizes, respectively. Planar detonations were produced by impacting the explosive with projectiles launched in a 72-mm bore gas gun. Impactors, impact velocity, and explosive thickness were chosen so that the run distance to detonation was always less than half the explosive thickness. For the high density plastic bonded explosives, particle velocity wave profiles were measured at an explosive/window interface using two VISAR interferometers. PMMA windows with vapor deposited aluminum mirrors were used for all experiments. Wave profiles for the powdered explosives were measured using magnetic particle velocity gauges. Estimates of the reaction zone parameters were obtained from the profiles using Hugoniots of the explosive and window.

  15. Coupled High Speed Imaging and Seismo-Acoustic Recordings of Strombolian Explosions at Etna, July 2014: Implications for Source Processes and Signal Inversions.

    NASA Astrophysics Data System (ADS)

    Taddeucci, J.; Del Bello, E.; Scarlato, P.; Ricci, T.; Andronico, D.; Kueppers, U.; Cannata, A.; Sesterhenn, J.; Spina, L.

    2015-12-01

    Seismic and acoustic surveillance is routinely performed at several persistent activity volcanoes worldwide. However, interpretation of the signals associated with explosive activity is still equivocal, due to both source variability and the intrinsically limited information carried by the waves. Comparison and cross-correlation of the geophysical quantities with other information in general and visual recording in particular is therefore actively sought. At Etna (Italy) in July 2014, short-lived Strombolian explosions ejected bomb- to lapilli-sized, molten pyroclasts at a remarkably repeatable time interval of about two seconds, offering a rare occasion to systematically investigate the seismic and acoustic fields radiated by this common volcanic source. We deployed FAMoUS (FAst, MUltiparametric Setup for the study of explosive activity) at 260 meters from the vents, recording more than 60 explosions in thermal and visible high-speed videos (50 to 500 frames per second) and broadband seismic and acoustic instruments (1 to 10000 Hz for the acoustic and from 0.01 to 30 Hz for the seismic). Analysis of this dataset highlights nonlinear relationships between the exit velocity and mass of ejecta and the amplitude and frequency of the acoustic signals. It also allows comparing different methods to estimate source depth, and to validate existing theory on the coupling of airwaves with ground motion.

  16. Explosive radiation in high Andean Hypericum-rates of diversification among New World lineages.

    PubMed

    Nürk, Nicolai M; Scheriau, Charlotte; Madriñán, Santiago

    2013-01-01

    The páramos, high-elevation Andean grasslands ranging from ca. 2800 m to the snow line, harbor one of the fastest evolving biomes worldwide since their appearance in the northern Andes 3-5 million years (Ma) ago. Hypericum (St. John's wort), with over 65% of its Neotropical species, has a center of diversity in these high Mountain ecosystems. Using nuclear rDNA internal transcribed spacer (ITS) sequences of a broad sample of New World Hypericum species we investigate phylogenetic patterns, estimate divergence times, and provide the first insights into diversification rates within the genus in the Neotropics. Two lineages appear to have independently dispersed into South America around 3.5 Ma ago, one of which has radiated in the páramos (Brathys). We find strong support for the polyphyly of section Trigynobrathys, several species of which group within Brathys, while others are found in temperate lowland South America (Trigynobrathys s.str.). All páramo species of Hypericum group in one clade. Within these páramo Hypericum species enormous phenotypic evolution has taken place (life forms from arborescent to prostrate shrubs) evidently in a short time frame. We hypothesize multiple mechanisms to be responsible for the low differentiation in the ITS region contrary to the high morphological diversity found in Hypericum in the páramos. Amongst these may be ongoing hybridization and incomplete lineage sorting, as well as the putative adaptive radiation, which can explain the contrast between phenotypic diversity and the close phylogenetic relationships. PMID:24062764

  17. Explosive radiation in high Andean Hypericum—rates of diversification among New World lineages

    PubMed Central

    Nürk, Nicolai M.; Scheriau, Charlotte; Madriñán, Santiago

    2013-01-01

    The páramos, high-elevation Andean grasslands ranging from ca. 2800 m to the snow line, harbor one of the fastest evolving biomes worldwide since their appearance in the northern Andes 3–5 million years (Ma) ago. Hypericum (St. John's wort), with over 65% of its Neotropical species, has a center of diversity in these high Mountain ecosystems. Using nuclear rDNA internal transcribed spacer (ITS) sequences of a broad sample of New World Hypericum species we investigate phylogenetic patterns, estimate divergence times, and provide the first insights into diversification rates within the genus in the Neotropics. Two lineages appear to have independently dispersed into South America around 3.5 Ma ago, one of which has radiated in the páramos (Brathys). We find strong support for the polyphyly of section Trigynobrathys, several species of which group within Brathys, while others are found in temperate lowland South America (Trigynobrathys s.str.). All páramo species of Hypericum group in one clade. Within these páramo Hypericum species enormous phenotypic evolution has taken place (life forms from arborescent to prostrate shrubs) evidently in a short time frame. We hypothesize multiple mechanisms to be responsible for the low differentiation in the ITS region contrary to the high morphological diversity found in Hypericum in the páramos. Amongst these may be ongoing hybridization and incomplete lineage sorting, as well as the putative adaptive radiation, which can explain the contrast between phenotypic diversity and the close phylogenetic relationships. PMID:24062764

  18. NQR detection of explosive simulants using RF atomic magnetometers

    NASA Astrophysics Data System (ADS)

    Monti, Mark C.; Alexson, Dimitri A.; Okamitsu, Jeffrey K.

    2016-05-01

    Nuclear Quadrupole Resonance (NQR) is a highly selective spectroscopic method that can be used to detect and identify a number of chemicals of interest to the defense, national security, and law enforcement community. In the past, there have been several documented attempts to utilize NQR to detect nitrogen bearing explosives using induction sensors to detect the NQR RF signatures. We present here our work on the NQR detection of explosive simulants using optically pumped RF atomic magnetometers. RF atomic magnetometers can provide an order of magnitude (or more) improvement in sensitivity versus induction sensors and can enable mitigation of RF interference, which has classically has been a problem for conventional NQR using induction sensors. We present the theory of operation of optically pumped RF atomic magnetometers along with the result of laboratory work on the detection of explosive simulant material. An outline of ongoing work will also be presented along with a path for a fieldable detection system.

  19. Modeling thermally driven energetic response of high explosives in ALE3D

    SciTech Connect

    Aro, C.; McCallen, R.C.; Neely, R.; Nichols, A.L. III; Sharp, R.

    1998-10-01

    The authors have improved their ability to model the response of energetic materials to thermal stimuli and the processes involved in the energetic response. Traditionally, the analyses of energetic materials have involved coupled thermal transport/chemical reaction codes. This provides only a reasonable estimate of the time and location of ensuing rapid reaction. To predict the violence of the reaction, the mechanical motion must be included in the wide range of time scales associated with the thermal hazard. The ALE3D code has been modified to assess the hazards associated with heating energetic materials in weapons by coupling to thermal transport model and chemistry models. They have developed an implicit time step option to efficiently and accurately compute the hours of heating to reaction of the energetic material. Since, on these longer time scales materials can be expected to have significant motion, it is even more important to provide high-order advection for all components, including the chemical species. They show two examples of coupled thermal/mechanical/chemical models of energetic materials in thermal environments.

  20. Creating High Energy Density Jets in Laboratory Environments

    NASA Astrophysics Data System (ADS)

    Coker, Robert

    2005-04-01

    A new experimental platform for the investigation of high Mach-number, high energy-density jets has been developed at the University of Rochester's Omega laser facility. Assuming the scalability of the Euler equations, the resulting mm-sized jets should scale to astrophysical objects such as Herbig-Haro objects and jet-driven supernovae that may involve jets with similar internal Mach numbers. This scalability still holds in the presence of radiation as long as the relative importance of radiative cooling is similar. In these experiments, either direct or indirect laser drive is used to launch a strong shock into a 125 micron thick titanium foil target that caps a 700 micron thick titanium washer. After the shock breaks out into the 300 micron diameter cylindrical hole in the washer, a dense, well-collimated jet with an energy density of more than 0.1 MJ per cc is formed. The jet is then imaged as it propagates for 100s of ns down a cylinder of low-density polymer foam. The experiments are diagnosed by point-projection with a micro-dot vanadium backligher. The field of view is several mm and the resolution is 15 microns. The X-ray radiographs show the hydrodynamically unstable jet and the bow shock driving into the surrounding foam. Such complex experimental data provide a challenge to hydrocodes and so are being used to test the hydrodynamic simulations of these types of flows. Initial comparisons between the data and LANL and AWE simulations will be shown. However, the high Reynolds numbers of both the laboratory and astrophysical jets suggest that, given sufficient time and shear, turbulence should develop; this cannot be reliably modeled by present, resolution-limited simulations. Future work concerning the applicability of the Omega experiments to astrophysical objects and the quantitative study of turbulent mixing via subgrid-scale models will be discussed.

  1. Microbial Evolution at High Pressure: Deep Sea and Laboratory Studies

    NASA Astrophysics Data System (ADS)

    Bartlett, D. H.

    2011-12-01

    Elevated hydrostatic pressures are present in deep-sea and deep-Earth environments where this physical parameter has influenced the evolution and characteristics of life. Piezophilic (high-pressure-adapted) microbes have been isolated from diverse deep-sea settings, and would appear likely to occur in deep-subsurface habitats as well. In order to discern the factors enabling life at high pressure my research group has explored these adaptations at various levels, most recently including molecular analyses of deep-sea trench communities, and through the selective evolution of the model microbe Escherichia coli in the laboratory to progressively higher pressures. Much of the field work has focused on the microbes present in the deeper portions of the Puerto Rico Trench (PRT)and in the Peru-Chile Trench (PCT), from 6-8.5 km below the sea surface (~60-85 megapascals pressure). Culture-independent phylogenetic data on the Bacteria and Archaea present on particles or free-living, along with data on the microeukarya present was complemented with genomic analyses and the isolation and characterization of microbes in culture. Metagenomic analyses of the PRT revealed increased genome sizes and an overrepresentation at depth of sulfatases for the breakdown of sulfated polysaccharides and specific categories of transporters, including those associated with the transport of diverse cations or carboxylate ions, or associated with heavy metal resistance. Single-cell genomic studies revealed several linneages which recruited to the PRT metagenome far better than existing marine microbial genome sequences. analyses. Novel high pressure culture approaches have yielded new piezophiles including species preferring very low nutrient levels, those living off of hydrocarbons, and those adapted to various electron donor/electron acceptor combinations. In order to more specifically focus on functions enabling life at increased pressure selective evolution experiments were performed with

  2. The combustion of explosives

    SciTech Connect

    Son, S. F.

    2001-01-01

    The safe use of energetic materials has been scientifically studied for over 100 years. Even with this long history of scientific inquiry, the level of understanding of the important deflagration phenomena in accidental initiations of high explosives remains inadequate to predict the response to possible thermal and mechanical (impact) scenarios. The! search also continues for more well behaved explosives and propellants that perform well, yet are insensitive. Once ignition occurs in an explosive, the question then becomes what the resulting violence will be. The classical view is that simple wave propagation proceeds from the ignition point. Recently, several experiments have elucidated the importance of reactive cracks involved in reaction violence in both thermally ignited experiments and impacted explosives, in contrast to classical assumptions, This work presents a viiw of reaction violence, in both thermal and mechanical insults, that argues for the importance of reactive cracks, rather than simple wave propagation processes. Recent work in this area will be reviewed and presented. Initial results involving novel energetic materials will also be discussed.

  3. The Combustion of Explosives

    NASA Astrophysics Data System (ADS)

    Son, S. F.

    2002-07-01

    The safe use of energetic materials has been scientifically studied for over 100 years. Even with this long history of scientific inquiry, the level of understanding of the important deflagration phenomena in accidental initiations of high explosives remains inadequate to predict the response to possible thermal and mechanical (impact) scenarios. The search also continues for improved explosives and propellants that perform well, yet are insensitive. Currently, the most significant uncertainties are in the processes immediately following ignition. Once ignition occurs in an explosive, the question then becomes what the resulting violence will be. The classical view is that simple wave propagation proceeds from the ignition point. Recently, several experiments have elucidated the importance of reactive cracks involved in reaction violence in both thermally ignited experiments and impacted explosives, in contrast to classical assumptions. This paper presents a view of reaction violence, in both thermal and mechanical insults, that argues for the importance of reactive cracks, rather than simple wave propagation processes. Recent work in this area will be reviewed and presented. Initial results involving novel energetic materials will also be discussed. Novel materials may yield insight into the mechanisms involved with rapid deflagration processes.

  4. MIT nuclear reactor laboratory high school teaching program

    SciTech Connect

    Olmez, I. )

    1991-11-01

    For the last 6 years, the Massachusetts Institute of Technology (MIT) Nuclear Reactor Laboratory's academic and scientific staff{sup a} have been conducting evening seminars for precollege science teachers, parents, and high school students from the New England area. These seminars, as outlined in this paper, are intended to give general information on nuclear technologies with specific emphasis on radiation physics, nuclear medicine, nuclear chemistry, and ongoing research activities at the MIT research reactor. The ultimate goal is to create interest or build on the already existing interest in science and technology by, for example, special student projects. Several small projects have already been completed ranging from environmental research to biological reactions with direct student involvement. Another outcome of these seminars was the change in attitudes of science teachers toward nuclear technology. Numerous letters have been received from the teachers and parents stating their previous lack of knowledge on the beneficial aspects of nuclear technologies and the subsequent inclusion of programs in their curriculum for educating students so that they may also develop a more positive attitude toward nuclear power.

  5. Progress In High Temperature Electrolysis At The Idaho National Laboratory

    SciTech Connect

    Carl M. Stoots; James E.O'Brien; J. Steve Herring; Joseph Hartvigsen

    2007-10-01

    The United States is considering the development of a domestic hydrogen-based energy economy. Hydrogen is of particular interest as a secondary energy carrier because it has the potential to be storable, transportable, environmentally benign, and useful in many chemical processes. Obviously, before a hydrogen economy can be implemented, an efficient and environmentally friendly means for large scale hydrogen production must be identified, proven, and developed. Hydrogen is now produced primarily via steam reforming of methane. However, from a long-term perspective, methane reforming is not a viable process for large-scale production of hydrogen since such fossil fuel conversion processes consume non-renewable resources and emit greenhouse gases. The U. S. National Research Council has recommended the use of water-splitting technologies to produce hydrogen using energy derived from a nuclear reactor. For the past several years, the Idaho National Laboratory has been actively studying the use of solid oxide fuel cells in conjunction with nuclear power for large-scale, high-temperature, electrolytic hydrogen production.

  6. Nejapa Tephra: The youngest (c. 1 ka BP) highly explosive hydroclastic eruption in western Managua (Nicaragua)

    NASA Astrophysics Data System (ADS)

    Rausch, Juanita; Schmincke, Hans-Ulrich

    2010-05-01

    Nejapa Maar (2.5 × 1.4 km, c. 120 m deep), the largest maar along the 15-km-long Holocene Nejapa-Miraflores Lineament (NML), is the source vent of the youngest relatively widespread basaltic tholeiitic tephra blanket (Nejapa Tephra: NT) in western central Nicaragua, as shown by isopachs and isopleths (Rausch and Schmincke, 2008). The NT covers an area of > 10 km 2 in W/NW Managua. The minimum total magma volume erupted is estimated as 0.09 km 3. Juvenile, dominantly slightly vesicular (20-40 vol.%) basically tachylitic cauliflower-shaped lapilli with an average density of 2.1 g/cm 3, make up > 90 vol.% of the deposit, while lithoclasts comprise < 10 vol.% except proximally. This, the paucity of fine-grained tuffs and the dominant plane-parallel bedding all suggest fragmentation by shallow interaction of a rising magma starting to vesiculate and fragment pyroclastically with external water. The complex particles so generated erupted in moderately high eruption columns (at least 7-10 km) and were dominantly deposited as dry to damp, warm to cool fallout. Minor surge transport is inferred from fine-grained, locally cross-bedded tephra beds chiefly north of Nejapa and just west of Asososca Maars. Synvolcanic faulting along the NML is inferred. Faults in the study area indicate that activation of the N-S-trending Nejapa-Miraflores Fault (NMF), representing the western flank of Managua Graben, preceded deposition of NT and underlying Masaya Tuff (c.1.8 ka BP), Chiltepe Pumice (c. 1.9 ka BP) and Masaya Triple Layer (2.1 ka BP). The NT deposit is underlain regionally by a paleosol and topped by a soil. The basal paleosol contains pottery sherds made by the Usulután negative technique during the Late Formative period (700 BCE-300 CE) (2.7-1.7 ka BP). The soil overlying NT contains pottery related to the Ometepe technique dated as between 1350 and 1550 CE (650-450 a BP). These, and the radiocarbon dates of the pottery-bearing paleosols (1245 ± 125 and 535 ± 110 a BP

  7. Micro-solid-phase extraction coupled to desorption electrospray ionization-high-resolution mass spectrometry for the analysis of explosives in soil.

    PubMed

    Bianchi, Federica; Gregori, Adolfo; Braun, Gabriele; Crescenzi, Carlo; Careri, Maria

    2015-01-01

    Home-made micro-solid-phase extraction (SPE) cartridges using different adsorbent materials were tested for the desorption electrospray ionization-high-resolution mass spectrometry (DESI-HRMS) determination of explosives like 2,4,6-trinitrotoluene, cyclotrimethylene-trinitramine, cyclotetramethylene-tetranitramine, pentaerythritol tetranitrate, and trinitrophenylmethylnitramine in soil samples. Quantitation limits in the low nanogram per kilogram range proved the reliability of the method for the detection of explosives at ultra-trace levels. The reduced sample preparation allowed for low costs and high-throughput analyses. Finally, the superior extraction capability of the method was proved by obtaining DESI-HRMS responses at least five times higher than those achieved by performing DESI-HRMS analyses of solid-liquid extracts spotted onto commercial polytetrafluoroethylene slides.

  8. Developments at the High Field Magnet Laboratory in Nijmegen

    NASA Astrophysics Data System (ADS)

    Perenboom, J. A. A. J.; Maan, J. C.; van Breukelen, M. R.; Wiegers, S. A. J.; den Ouden, A.; Wulffers, C. A.; van der Zande, W. J.; Jongma, R. T.; van der Meer, A. F. G.; Redlich, B.

    2013-03-01

    The High Field Magnet Laboratory at the Radboud University Nijmegen is rapidly expanding its capabilities. The developments encompass both organizational changes and new possibilities for research. The organization of the HFML was strengthened as a consequence of stronger participation of the Foundation for Fundamental Research on Matter (FOM), and an increase of the core-funding. This change makes that HFML is now considered on a national level as large research facility that operates at an international scale. At the same time work is underway to build new and powerful magnets, and provide electromagnetic radiation for magneto-spectroscopic studies. Electromagnetic radiation in the infrared and far-infrared spectrum will soon be available in the HFML with wavelengths between 3 μm and 1.5 mm, produced by the `FELIX' facility, comprising the long-wavelength free electron laser `FLARE' that in September 2011 produced its first light and the free electron lasers that have been moved from Rijnhuizen to Nijmegen. In magnet technology great strides are made to make magnets available for the user community with unprecedented performance: late in 2012 we hope to commission a new all-resistive magnet system that will generate a steady magnetic field as high as 38 T, by fully exploiting the maximum power of the installation, i.e. 20 MW, and using all available improvements in the design and construction of `Florida-Bitter' resistive magnets. We are also well underway with the design of a 45 T hybrid magnet system, using Nb3Sn superconductors and wind-and-react Cable-in-Conduit technology.

  9. The NASA Lewis Research Center High Temperature Fatigue and Structures Laboratory

    NASA Technical Reports Server (NTRS)

    Mcgaw, M. A.; Bartolotta, P. A.

    1987-01-01

    The physical organization of the NASA Lewis Research Center High Temperature Fatigue and Structures Laboratory is described. Particular attention is given to uniaxial test systems, high cycle/low cycle testing systems, axial torsional test systems, computer system capabilities, and a laboratory addition. The proposed addition will double the floor area of the present laboratory and will be equipped with its own control room.

  10. Comparison of Electron Capture and Beta Decay Rates in High Temperature Environment in Explosion of Supernova Type II

    NASA Astrophysics Data System (ADS)

    Baruah, Rulee

    2015-08-01

    It is generally acknowledged that Type II supernova result from the collapse of iron core of a massive star which , at least in some cases, produces a neutron star. At this stage, the neutrinos are produced by neutronization which speeds up as collapse continues. During collapse an outward bound shock wave forms in the matter falling onto the nearly stationary core which shows reflectivity of matter . The conditions behind the shock at 100 to 200 km are suitable for neutrino heating . This neutrino heating blows a hot bubble above the protoneutron star and is the most important source of energy for Supernova explosion . At this stage , we try to attain the r-process path responsible for the production of heavy elements beyond iron , which are otherwise not possible to be formed by fusion reactions . The most interesting evolution occurs as temperature falls from 1010 K to 109 K . At these high temperature conditions , the near critical fluids after fusion reactions are forbidden and transform into the respective atoms by r-process path which on beta decaying produce the ultimate elements of the periodic chart . Another astrophysical parameter needed for our analysis is neutron number density which we take to be greater than 1020 cm-3 . With these , at different entropy environments , we assign the neutron binding energy that represents the r-process path in the chart of nuclides . Along the path , the experimental data of observed elements matches our calculated one . It is found that the dynamical timescale of the final collapse is dominated by electron capture on nuclei and not on free protons. It is also found that the beta decay rates are much higher than the corresponding electron capture rates at the same classical condition.

  11. Comparison of electron capture and beta decay rates in high temperature environment in explosion of supernova type II

    NASA Astrophysics Data System (ADS)

    Baruah, Rulee

    It is generally acknowledged that Type II supernova results from the collapse of iron core of a massive star which, at least in some cases, produces a neutron star. At this stage, the neutrinos are produced by neutronization which speeds up as collapse continues. During collapse an outward bound shock wave forms in the matter falling onto the nearly stationary core. The conditions behind the shock at 100 to 200 km are suitable for neutrino heating. This neutrino heating blows a hot bubble above the protoneutron star and is the most important source of energy for Supernova explosion. At this stage, we try to attain the r-process (rapid neutron capture process) path responsible for the production of heavy elements beyond iron, which are otherwise not possible to be formed by fusion reactions. The most interesting evolution occurs as temperature falls from 1010 K to 109 K. At these high temperature conditions, the near critical fluids after fusion reactions transform into the respective atoms by r-process path which on beta decaying produce the ultimate elements of the periodic chart. Another astrophysical parameter needed for our analysis is neutron number density which we take to be greater than 1020 cm^{-3}. With these, at different entropy environments, we assign the neutron binding energy that represents the r-process path in the chart of nuclides. Along the path, the experimental data of observed elements matches our calculated one. It is found that the dynamical timescale of the final collapse is dominated by electron capture on nuclei and not on free protons. It is also found that the beta decay rates are much higher than the corresponding electron capture rates at the same classical condition.

  12. In-situ monitoring of flow-permeable surface area of high explosive powder using small sample masses

    DOE PAGESBeta

    Maiti, Amitesh; Han, Yong; Zaka, Fowzia; Gee, Richard H.

    2015-02-17

    To ensure good performance of high explosive devices over long periods of time, initiating powders need to maintain their specific surface area within allowed margins during the entire duration of deployment. A common diagnostic used in this context is the Fisher sub-sieve surface area (FSSA). Furthermore, commercial permeametry instruments measuring the FSSA requires the utilization of a sample mass equal to the crystal density of the sample material, an amount that is often one or two orders of magnitude larger than the typical masses found in standard detonator applications. Here we develop a customization of the standard device that canmore » utilize just tens of milligram samples, and with simple calibration yield FSSA values at ac curacy levels comparable to the standard apparatus. This necessitated a newly designed sample holder, made from a material of low coefficient of thermal expansion, which is conveniently transferred between an aging chamber and a re-designed permeametry tube. This improves the fidelity of accelerated aging studies by allowing measurement on the same physical sample at various time - instants during the aging process, and by obviating the need for a potentially FSSA-altering powder re-compaction step. We used the customized apparatus to monitor the FSSA evolution of a number of undoped and homolog-doped PETN powder samples that were subjected to artificial aging for several months at elevated temperatures. These results, in conjunction with an Arrhenius-based aging model were used to assess powder-coarsening - rates under long-term storage.« less

  13. 42 CFR 493.1453 - Condition: Laboratories performing high complexity testing; clinical consultant.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Condition: Laboratories performing high complexity testing; clinical consultant. The laboratory must have a... testing; clinical consultant. 493.1453 Section 493.1453 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION...

  14. High Performance Liquid Chromatography Experiments to Undergraduate Laboratories

    ERIC Educational Resources Information Center

    Kissinger, Peter T.; And Others

    1977-01-01

    Reviews the principles of liquid chromatography with electrochemical detection (LCEC), an analytical technique that incorporates the advantages of both liquids chromatography and electrochemistry. Also suggests laboratory experiments using this technique. (MLH)

  15. Understanding Magma Storage Conditions that Produce Highly Explosive Monogenetic Basaltic Eruptions Using Olivine-Hosted Melt Inclusions from Sunset Crater, AZ

    NASA Astrophysics Data System (ADS)

    Allison, C. M.; Roggensack, K.; Clarke, A. B.

    2014-12-01

    To investigate mechanisms of explosive basaltic volcanism, we studied the ca. 1085 AD Sunset Crater eruption in the San Francisco Volcanic Field (SFVF) of northern Arizona. This eruption, the youngest in the SFVF, first featured fissure eruptions (explosive phases 1-2) and a small lava flow, and then activity narrowed to a central vent producing explosive phases 3-8 and two additional lava flows. While the first two phases were Strombolian-style explosions, middle phases (3-5) were subplinian in character and produced an anomalously large tephra deposit. The final phases (6-8) are poorly characterized at this stage. The total erupted volume of lava and tephra is >0.7 km3 DRE of alkali olivine basalt with a large proportion of crystal-free glass and low phenocryst content. We studied 82 primary melt inclusions (MIs) in the largest tephra units (explosive phases 3, 4) to investigate magma volatiles and storage conditions. To prioritize primary volatile contents, we picked rapidly quenched free olivine crystals (Fo 81-85; 0.5-2 mm) and selected large volume MIs (50-180 μm) located near crystal cores for analysis. We observed vapor bubbles in all MIs and also noted rare occurrences of CO2-rich gas inclusions. MIs show little major element variability suggesting little crystal fractionation (K2O 0.8-1.1 wt.%). Post-entrapment crystallization is also minor (2-9%). The MI compositions from the two phases largely overlap, with phase 4 skewed to slightly higher K2O. FTIR spectroscopy shows that the MIs are relatively dry and CO2-rich. Water abundances vary 0.8-1.6 wt.% with a median of 1.25 wt.%, while most MIs have CO2 abundances 1,600-3,400 ppm. Phases 3 and 4 are essentially identical in water content. CO2 contents of phases 3 and 4 show considerable overlap, however the phase 4 MIs are skewed toward high CO2 (>2,500 ppm). These results require a minimum MI entrapment depth of ~11 km from fluid saturation constraints. Overall, the MIs indicate a largely homogeneous

  16. Explosive Detection and Identification by PGNAA

    SciTech Connect

    E.H. Seabury; A.J. Caffrey

    2004-11-01

    The goal of this project was to determine the feasibility of using field-portable prompt gamma-ray neutron activation analysis (PGNAA) to detect and identify explosives in improvised nuclear devices (INDs). The studies were carried out using the Monte Carlo N-Particle (MCNP) code developed at Los Alamos National Laboratory. The model results were tested experimentally using explosive simulants and the PINS PGNAA system developed at Idaho National Engineering and Environmental Laboratory (INEEL). The results of the MCNP calculations and PINS measurements are presented in this report. The calculations and measurements were in good agreement and indicate that most explosives are readily distinguishable from one another.

  17. Lightning Protection for Explosive Facilities

    SciTech Connect

    Ong, M

    2001-12-01

    Lawrence Livermore National Laboratory funds construction of lightning protection systems to protect explosive processing and storage facilities. This paper provides an intuitive understanding of the lighting risks and types of lightning protection available. Managers can use this information to decide if limited funds should be spent constructing a lightning protection system for their own facilities. This paper answers the following questions: (1) Why do you need lightning protection systems? (2) How do lightning protection systems work? and (3) Why are there no documented cases of lightning problems at existing explosive facilities?

  18. Shock desensitizing of solid explosives

    SciTech Connect

    Davis, William C

    2010-01-01

    Solid explosive can be desensitized by a shockwave too weak to initiate it promptly, and desensitized explosive does not react although its chemical composition is almost unchanged. A strong second shock does not cause reaction until it overtakes the first shock. The first shock, if it is strong enough, accelerates very slowly at first, and then more rapidly as detonation approaches. These facts suggest that there are two competing reactions. One is the usual explosive goes to products with the release of energy, and the other is explosive goes to dead explosive with no chemical change and no energy release. The first reaction rate is very sensitive to the local state, and the second is only weakly so. At low pressure very little energy is released and the change to dead explosive dominates. At high pressure, quite the other way, most of the explosive goes to products. Numerous experiments in both the initiation and the full detonation regimes are discussed and compared in support of these ideas.

  19. Shock desensitizing of solid explosive

    SciTech Connect

    Davis, William C

    2010-01-01

    Solid explosive can be desensitized by a shock wave too weak to initiate it promptly, and desensitized explosive does not react although its chemical composition is almost unchanged. A strong second shock does not cause reaction until it overtakes the first shock. The first shock, if it is strong enough, accelerates very slowly at first, and then more rapidly as detonation approaches. These facts suggest that there are two competing reactions. One is the usual explosive goes to products with the release of energy, and the other is explosive goes to dead explosive with no chemical change and no energy release. The first reaction rate is very sensitive to the local state, and the second is only weakly so. At low pressure very little energy is released and the change to dead explosive dominates. At high pressure, quite the other way, most of the explosive goes to products. Numerous experiments in both the initiation and the full detonation regimes are discussed and compared in testing these ideas.

  20. Detection of explosives in soils

    DOEpatents

    Chambers, William B.; Rodacy, Philip J.; Phelan, James M.; Woodfin, Ronald L.

    2002-01-01

    An apparatus and method for detecting explosive-indicating compounds in subsurface soil. The apparatus has a probe with an adsorbent material on some portion of its surface that can be placed into soil beneath the ground surface, where the adsorbent material can adsorb at least one explosive-indicating compound. The apparatus additional has the capability to desorb the explosive-indicating compound through heating or solvent extraction. A diagnostic instrument attached to the probe detects the desorbed explosive-indicating compound. In the method for detecting explosive-indicating compounds in soil, the sampling probe with an adsorbent material on at least some portion of a surface of the sampling probe is inserted into the soil to contact the adsorbent material with the soil. The explosive-indicating compounds are then desorbed and transferred as either a liquid or gas sample to a diagnostic tool for analysis. The resulting gas or liquid sample is analyzed using at least one diagnostic tool selected from the group consisting of an ion-mobility spectrometer, a gas chromatograph, a high performance liquid chromatograph, a capillary electrophoresis chromatograph, a mass spectrometer, a Fourier-transform infrared spectrometer and a Raman spectrometer to detect the presence of explosive-indicating compounds.

  1. An assessment of high-energy explosives and metal contamination in soil at TA-67 (12), L-Site, and TA-14, Q-Site

    SciTech Connect

    Haywood, W.; McRae, D.; Powell, J.; Harris, B.W.

    1995-01-01

    The results of the field investigation to determine the kind and concentration of explosives found in the soil and on articles at sites known to be contaminated with energetic materials are given in this report. We are concerned about safety and health hazards associated with some explosives, nitro-organics and organic nitrates. Results from the use of the old and new field spot-test kits to detect the presence of energetic materials are given. Also included are data from the high-performance liquid chromatography (HPLC) analyses of acetonitrile extracts from Q-Site soil samples, and data from the energy-dispersive x-ray fluorescence (EDXRF) analyses for hazardous metals on the same samples.

  2. High accuracy laboratory spectroscopy to support active greenhouse gas sensing

    NASA Astrophysics Data System (ADS)

    Long, D. A.; Bielska, K.; Cygan, A.; Havey, D. K.; Okumura, M.; Miller, C. E.; Lisak, D.; Hodges, J. T.

    2011-12-01

    Recent carbon dioxide (CO2) remote sensing missions have set precision targets as demanding as 0.25% (1 ppm) in order to elucidate carbon sources and sinks [1]. These ambitious measurement targets will require the most precise body of spectroscopic reference data ever assembled. Active sensing missions will be especially susceptible to subtle line shape effects as the narrow bandwidth of these measurements will greatly limit the number of spectral transitions which are employed in retrievals. In order to assist these remote sensing missions we have employed frequency-stabilized cavity ring-down spectroscopy (FS-CRDS) [2], a high-resolution, ultrasensitive laboratory technique, to measure precise line shape parameters for transitions of O2, CO2, and other atmospherically-relevant species within the near-infrared. These measurements have led to new HITRAN-style line lists for both 16O2 [3] and rare isotopologue [4] transitions in the A-band. In addition, we have performed detailed line shape studies of CO2 transitions near 1.6 μm under a variety of broadening conditions [5]. We will address recent measurements in these bands as well as highlight recent instrumental improvements to the FS-CRDS spectrometer. These improvements include the use of the Pound-Drever-Hall locking scheme, a high bandwidth servo which enables measurements to be made at rates greater than 10 kHz [6]. In addition, an optical frequency comb will be utilized as a frequency reference, which should allow for transition frequencies to be measured with uncertainties below 10 kHz (3×10-7 cm-1). [1] C. E. Miller, D. Crisp, P. L. DeCola, S. C. Olsen, et al., J. Geophys. Res.-Atmos. 112, D10314 (2007). [2] J. T. Hodges, H. P. Layer, W. W. Miller, G. E. Scace, Rev. Sci. Instrum. 75, 849-863 (2004). [3] D. A. Long, D. K. Havey, M. Okumura, C. E. Miller, et al., J. Quant. Spectrosc. Radiat. Transfer 111, 2021-2036 (2010). [4] D. A. Long, D. K. Havey, S. S. Yu, M. Okumura, et al., J. Quant. Spectrosc

  3. Use of a fast near-infrared spectrometer for absorption and emission measurements within the expanding blast wave of a high explosive

    NASA Astrophysics Data System (ADS)

    Koch, Jon D.; Carney, Joel; Lightstone, James; Piecuch, Scott

    2012-03-01

    We demonstrate the use of a fast InGaAs array and spectrometer to measure properties related to near-infrared absorption and emission (750 nm -1500 nm) following a high explosive detonation. Using a broadband light source and a rigid absorption gauge, gas temperatures are measured at a rate of 20 kHz for a period of several milliseconds behind the blast wave from a PETN, PBXN-5, and PBXN-113 detonations. The temperature and concentration of water vapor is determined by fitting experimental transmission spectra to a simulated database. Strong emission signatures obtained during the PETN breakout event (integrated over approximately the first 20 microseconds) indicate the presence of high energy nitrogen and oxygen atoms. Measurements from water absorption at a distance of 23 cm from the PETN charge indicate temperatures decaying from 1600 K to 600 K during the first few milliseconds, and measurements of non-ideal explosives with optically thick postdetonation environments are also demonstrated. These measurements are intended to aid the development of detonation and explosive simulations.

  4. Searching for a new family of insensitive high explosives by introducing N hybridization and N-oxides into a cage cubane.

    PubMed

    Wu, Qiong; Zhu, Weihua; Xiao, Heming

    2014-11-01

    A new family of energetic azacubane N-oxides were designed by introducing N-oxides into azacubanes and investigated by using density functional theory. Introducing the N-oxides into the azacubanes could improve their detonation performance significantly due to the increase of the OB and ρ but would also increase the sensitivity to some extent. These effects would be further enhanced as the numbers of N-oxides increase. Among all the designed azacubane N-oxides, D6-4 (1,3,5,7-tetraazacubane-1,3,5,7-tetraoxides) has higher detonation performance than one famous high explosive HMX (1,3,5,7-tetranitro-1,3,5,7-tetrazocane) and lower sensitivity than one very insensitive explosive TNT (1-methyl-2,4,6-trinitrobenzene), suggesting that its overall performance is outstanding and may be considered as the potential candidate of insensitive high explosives. The internal small cage C-N skeleton of D6-4 is surrounded by the external big cage hydrogen bonds and this special double cage structure may be an important reason why it has low sensitivity.

  5. High Reproducibility of ELISPOT Counts from Nine Different Laboratories.

    PubMed

    Sundararaman, Srividya; Karulin, Alexey Y; Ansari, Tameem; BenHamouda, Nadine; Gottwein, Judith; Laxmanan, Sreenivas; Levine, Steven M; Loffredo, John T; McArdle, Stephanie; Neudoerfl, Christine; Roen, Diana; Silina, Karina; Welch, Mackenzie; Lehmann, Paul V

    2015-01-01

    The primary goal of immune monitoring with ELISPOT is to measure the number of T cells, specific for any antigen, accurately and reproducibly between different laboratories. In ELISPOT assays, antigen-specific T cells secrete cytokines, forming spots of different sizes on a membrane with variable background intensities. Due to the subjective nature of judging maximal and minimal spot sizes, different investigators come up with different numbers. This study aims to determine whether statistics-based, automated size-gating can harmonize the number of spot counts calculated between different laboratories. We plated PBMC at four different concentrations, 24 replicates each, in an IFN-γ ELISPOT assay with HCMV pp65 antigen. The ELISPOT plate, and an image file of the plate was counted in nine different laboratories using ImmunoSpot® Analyzers by (A) Basic Count™ relying on subjective counting parameters set by the respective investigators and (B) SmartCount™, an automated counting protocol by the ImmunoSpot® Software that uses statistics-based spot size auto-gating with spot intensity auto-thresholding. The average coefficient of variation (CV) for the mean values between independent laboratories was 26.7% when counting with Basic Count™, and 6.7% when counting with SmartCount™. Our data indicates that SmartCount™ allows harmonization of counting ELISPOT results between different laboratories and investigators. PMID:25585297

  6. Explosive signatures: Pre & post blast

    NASA Astrophysics Data System (ADS)

    Bernier, Evan Thomas

    Manuscripts 1 and 2 of this dissertation both involve the pre-blast detection of trace explosive material. The first manuscript explores the analysis of human hair as an indicator of exposure to explosives. Field analysis of hair for trace explosives is quick and non-invasive, and could prove to be a powerful linkage to physical evidence in the form of bulk explosive material. Individuals tested were involved in studies which required handling or close proximity to bulk high explosives such as TNT, PETN, and RDX. The second manuscript reports the results of research in the design and application of canine training aids for non-traditional, peroxide-based explosives. Organic peroxides such as triacetonetriperoxide (TATP) and hexamethylenetriperoxidediamine (HMTD) can be synthesized relatively easily with store-bought ingredients and have become popular improvised explosives with many terrorist groups. Due to the hazards of handling such sensitive compounds, this research established methods for preparing training aids which contained safe quantities of TATP and HMTD for use in imprinting canines with their characteristic odor. Manuscripts 3 and 4 of this dissertation focus on research conducted to characterize pipe bombs during and after an explosion (post-blast). Pipe bombs represent a large percentage of domestic devices encountered by law enforcement. The current project has involved the preparation and controlled explosion of over 90 pipe bombs of different configurations in order to obtain data on fragmentation patterns, fragment velocity, blast overpressure, and fragmentation distance. Physical data recorded from the collected fragments, such as mass, size, and thickness, was correlated with the relative power of the initial device. Manuscript 4 explores the microstructural analysis of select pipe bomb fragments. Shock-loading of the pipe steel led to plastic deformation and work hardening in the steel grain structure as evidenced by optical microscopy and

  7. Chromospheric explosions

    NASA Technical Reports Server (NTRS)

    Doschek, G. A.; theory. (3) Resolved: Most chromospheric h; theory. (3) Resolved: Most chromospheric h

    1986-01-01

    Three issues relative to chromospheric explosions were debated. (1) Resolved: The blue-shifted components of x-ray spectral lines are signatures of chromospheric evaporation. It was concluded that the plasma rising with the corona is indeed the primary source of thermal plasma observed in the corona during flares. (2) Resolved: The excess line broading of UV and X-ray lines is accounted for by a convective velocity distribution in evaporation. It is concluded that the hypothesis that convective evaporation produces the observed X-ray line widths in flares is no more than a hypothesis. It is not supported by any self-consistent physical theory. (3) Resolved: Most chromospheric heating is driven by electron beams. Although it is possible to cast doubt on many lines of evidence for electron beams in the chromosphere, a balanced view that debaters on both sides of the question might agree to is that electron beams probably heat the low corona and upper chromosphere, but their direct impact on evaporating the chromosphere is energetically unimportant when compared to conduction. This represents a major departure from the thick-target flare models that were popular before the Workshop.

  8. Eigenvalue Detonation of Combined Effects Aluminized Explosives

    NASA Astrophysics Data System (ADS)

    Capellos, Christos; Baker, Ernest; Balas, Wendy; Nicolich, Steven; Stiel, Leonard

    2007-06-01

    This paper reports on the development of theory and performance for recently developed combined effects aluminized explosives. Traditional high energy explosives used for metal pushing incorporate high loading percentages of HMX or RDX, whereas blast explosives incorporate some percentage of aluminum. However, the high blast explosives produce increased blast energies, with reduced metal pushing capability due to late time aluminum reaction. Metal pushing capability refers to the early volume expansion work produced during the first few volume expansions associated with cylinder wall velocities and Gurney energies. Our Recently developed combined effects aluminized explosives (PAX-29C, PAX-30, PAX-42) are capable of achieving excellent metal pushing and high blast energies. Traditional Chapman-Jouguet detonation theory does not explain the observed detonation states achieved by these combined effects explosives. This work demonstrates, with the use of cylinder expansion data and thermochemical code calculations (JAGUAR and CHEETAH), that eigenvalue detonation theory explains the observed behavior.

  9. Using Cellular Slime Molds in the High School Laboratory

    ERIC Educational Resources Information Center

    Haskins, P. B.

    1977-01-01

    Described is the life cycle of the cellular slime molds Acrasiales. Experiments that can be used to explore the aggregation, migration, and culmination activities of the organism are suggested. Laboratory procedures for culturing these slime molds and listings of biological supply houses and literature references are also given. (MA)

  10. Structural Science Laboratory Supplement. High-Technology Training Module.

    ERIC Educational Resources Information Center

    Luthens, Roger

    This module, a laboratory supplement on the theory of bending and properties of sections, is part of a first-year, postsecondary structural science technical support course for architectural drafting and design. The first part of this two-part supplement is directed at the instructor and includes the following sections: program objectives; course…

  11. Quantum Cascade Lasers (QCLs) for standoff explosives detection : LDRD 138733 final report.

    SciTech Connect

    Theisen, Lisa Anne; Linker, Kevin Lane

    2009-09-01

    Continued acts of terrorism using explosive materials throughout the world have led to great interest in explosives detection technology, especially technologies that have a potential for remote or standoff detection. This LDRD was undertaken to investigate the benefit of the possible use of quantum cascade lasers (QCLs) in standoff explosives detection equipment. Standoff detection of explosives is currently one of the most difficult problems facing the explosives detection community. Increased domestic and troop security could be achieved through the remote detection of explosives. An effective remote or standoff explosives detection capability would save lives and prevent losses of mission-critical resources by increasing the distance between the explosives and the intended targets and/or security forces. Many sectors of the US government are urgently attempting to obtain useful equipment to deploy to our troops currently serving in hostile environments. This LDRD was undertaken to investigate the potential benefits of utilizing quantum cascade lasers (QCLs) in standoff detection systems. This report documents the potential opportunities that Sandia National Laboratories can contribute to the field of QCL development. The following is a list of areas where SNL can contribute: (1) Determine optimal wavelengths for standoff explosives detection utilizing QCLs; (2) Optimize the photon collection and detection efficiency of a detection system for optical spectroscopy; (3) Develop QCLs with broader wavelength tunability (current technology is a 10% change in wavelength) while maintaining high efficiency; (4) Perform system engineering in the design of a complete detection system and not just the laser head; and (5) Perform real-world testing with explosive materials with commercial prototype detection systems.

  12. The spectacular evolution of Supernova 1996al over 15 yr: a low-energy explosion of a stripped massive star in a highly structured environment

    NASA Astrophysics Data System (ADS)

    Benetti, S.; Chugai, N. N.; Utrobin, V. P.; Cappellaro, E.; Patat, F.; Pastorello, A.; Turatto, M.; Cupani, G.; Neuhäuser, R.; Caldwell, N.; Pignata, G.; Tomasella, L.

    2016-03-01

    Spectrophotometry of SN 1996al carried out throughout 15 yr is presented. The early photometry suggests that SN 1996al is a linear Type II supernova, with an absolute peak of MV ˜ -18.2 mag. Early spectra present broad asymmetric Balmer emissions, with superimposed narrow lines with P-Cygni profile, and He I features with asymmetric broad emission components. The analysis of the line profiles shows that the H and He broad components form in the same region of the ejecta. By day +142, the Hα profile dramatically changes: the narrow P-Cygni profile disappears, and the Hα is fitted by three emission components that will be detected over the remaining 15 yr of the supernova (SN) monitoring campaign. Instead, the He I emissions become progressively narrower and symmetric. A sudden increase in flux of all He I lines is observed between 300 and 600 d. Models show that the SN luminosity is sustained by the interaction of low-mass (˜1.15 M⊙) ejecta, expelled in a low kinetic energy (˜1.6 × 1050 erg) explosion, with highly asymmetric circumstellar medium. The detection of Hα emission in pre-explosion archive images suggests that the progenitor was most likely a massive star (˜25 M⊙ ZAMS) that had lost a large fraction of its hydrogen envelope before explosion, and was hence embedded in a H-rich cocoon. The low-mass ejecta and modest kinetic energy of the explosion are explained with massive fallback of material into the compact remnant, a 7-8-M⊙ black hole.

  13. Explosive Spot Joining of Metals

    NASA Technical Reports Server (NTRS)

    Bement, Laurence J. (Inventor); Perry, Ronnie B. (Inventor)

    1997-01-01

    The invention is an apparatus and method for wire splicing using an explosive joining process. The apparatus consists of a prebend, U-shaped strap of metal that slides over prepositioned wires. A standoff means separates the wires from the strap before joining. An adhesive means holds two ribbon explosives in position centered over the U-shaped strap. A detonating means connects to the ribbon explosives. The process involves spreading strands of each wire to be joined into a flat plane. The process then requires alternating each strand in alignment to form a mesh-like arrangement with an overlapped area. The strap slides over the strands of the wires. and the standoff means is positioned between the two surfaces. The detonating means then initiates the ribbon explosives that drive the strap to accomplish a high velocity. angular collision between the mating surfaces. This collision creates surface melts and collision bonding resulting in electron-sharing linkups.

  14. Ammonium nitrate explosive systems

    DOEpatents

    Stinecipher, Mary M.; Coburn, Michael D.

    1981-01-01

    Novel explosives which comprise mixtures of ammonium nitrate and an ammonium salt of a nitroazole in desired ratios are disclosed. A preferred nitroazole is 3,5-dinitro-1,2,4-triazole. The explosive and physical properties of these explosives may readily be varied by the addition of other explosives and oxidizers. Certain of these mixtures have been found to act as ideal explosives.

  15. Shock Initiation of Heterogeneous Explosives

    SciTech Connect

    Reaugh, J E

    2004-05-10

    The fundamental picture that shock initiation in heterogeneous explosives is caused by the linking of hot spots formed at inhomogeneities was put forward by several researchers in the 1950's and 1960's, and more recently. Our work uses the computer hardware and software developed in the Advanced Simulation and Computing (ASC) program of the U.S. Department of Energy to explicitly include heterogeneities at the scale of the explosive grains and to calculate the consequences of realistic although approximate models of explosive behavior. Our simulations are performed with ALE-3D, a three-dimensional, elastic-plastic-hydrodynamic Arbitrary Lagrange-Euler finite-difference program, which includes chemical kinetics and heat transfer, and which is under development at this laboratory. We developed the parameter values for a reactive-flow model to describe the non-ideal detonation behavior of an HMX-based explosive from the results of grain-scale simulations. In doing so, we reduced the number of free parameters that are inferred from comparison with experiment to a single one - the characteristic defect dimension. We also performed simulations of the run to detonation in small volumes of explosive. These simulations illustrate the development of the reaction zone and the acceleration of the shock front as the flame fronts start from hot spots, grow, and interact behind the shock front. In this way, our grain-scale simulations can also connect to continuum experiments directly.

  16. Inquiry-Based Laboratory Activities in Electrochemistry: High School Students' Achievements and Attitudes

    ERIC Educational Resources Information Center

    Sesen, Burcin Acar; Tarhan, Leman

    2013-01-01

    This study aimed to investigate the effects of inquiry-based laboratory activities on high school students' understanding of electrochemistry and attitudes towards chemistry and laboratory work. The participants were 62 high school students (average age 17 years) in an urban public high school in Turkey. Students were assigned to experimental (N =…

  17. The New High Magnetic Field Laboratory at Dresden: a Pulsed-Field Laboratory at an IR Free-Electron-Laser

    SciTech Connect

    Pobell, F.; Bianchi, A. D.; Herrmannsdoerfer, T.; Krug, H.; Zherlitsyn, S.; Zvyagin, S.; Wosnitza, J.

    2006-09-07

    We report on the construction of a new high magnetic field user laboratory which will offer pulsed-field coils in the range (60 T, 500 ms, 40 mm) to (100 T, 10 ms, 20 mm) for maximum field, pulse time, and bore diameter of the coils. These coils will be energized by a modular 50 MJ/24 kV capacitor bank. Besides many other experimental techniques, as unique possibilities NMR in pulsed fields as well as infrared spectroscopy at 5 to 150 {mu}m will be available by connecting the pulsed field laboratory to a nearby free-electron-laser facility.

  18. Highly explosive eruption of the monogenetic 8.6 ka BP La Vache et Lassolas scoria cone complex (Chaîne des Puys, France)

    NASA Astrophysics Data System (ADS)

    Jordan, S. C.; Le Pennec, J.-L.; Gurioli, L.; Roche, O.; Boivin, P.

    2016-03-01

    The eruption of the trachy-basaltic La Vache and Lassolas cone complex was the youngest eruption (ca. 8.6 ka BP) and one of the most violent in the Chaîne des Puys, France. Here we present field data and results of grain size, componentry and clast density measurements of different layers of the widespread tephra deposit that is associated with this cone-forming eruption. Our data indicates five main eruption phases comprising a vent-opening phase, a second sustained highly explosive phase, a third and fourth violent Strombolian phase and a fifth dominantly effusive phase. The layer formed by the opening phase is rich in lithic material, which was previously considered to be the result of phreatomagmatic activity. The data presented here on the componentry and textures of the pyroclastic material contradict this hypothesis. We propose instead that the material of the basal layer results from fragmentation caused by the explosion of a first arriving gas-dominated phase. The variations in eruption intensity during the main eruption phases are interpreted here to be the result of gas segregation within the plumbing system and fluxes in the magma ascent rate during the eruption. Significant amount of gas segregation is indicated by the deposition of both gas-poor and gas-rich material and by the presence of plate tephra. This is also supported by the simultaneous ejection of tephra and lava from both cones during most of the explosive activity. We suggest that gas segregation occurred within shallow intrusions and that fresh ascending material in the main conduit mixed with degassed material that flow back into the conduit from the intrusion before fragmentation. The interaction of the ascending magma and the opening of intrusions may have controlled the evolution and explosivity of the eruption. The high explosivity at the beginning of the eruption and the wide dispersal area, demonstrate that scoria cone eruptions in monogenetic fields can impose a major threat to

  19. Macro-Scale Reactive Flow Model for High-Explosive Detonation in Support of ASCI Weapon Safety Milepost

    SciTech Connect

    Reaugh, J E

    2002-01-03

    Explosive grain-scale simulations are not practical for weapon safety simulations. Indeed for nearly ideal explosives with reaction zones of order 500 {micro}m, even reactive flow models are not practical for weapon safety simulations. By design, reactive flow models must resolve the reaction zone, which implies computational cells with dimension of order 50 {micro}m for such explosives. The desired result for a simulation in which the reaction zone is not resolved is that the explosive behaves as an ideal one. The pressure at the shock front rises to the Chapman-Jouget (CJ) pressure with a reaction zone dimension that is like that of a shock propagating in an unreactive medium, on the order of a few computational cells. It should propagate with the detonation velocity that is determined by the equation of state of the products. In the past, this was achieved in one dimensional simulations with ''beta-burn'', a method in which the extent of conversion to final product is proportional to the approach of the specific volume in the shock front to the specific volume of the CJ state. One drawback with this method is that there is a relatively long build-up to steady detonation that is typically 50 to 100 computational cells. The need for relatively coarsely zoned simulations in two dimensions lead to ''program-burn'' by which the time to detonation can be determined by a simple ray-tracing algorithm when there are no barriers or shadows. Complications arise in two and three dimensions to the extent that some calculations of the lighting time in complex geometry can give incorrect results. We sought to develop a model based on reactive flow that might help the needs of the Weapon Safety Simulation milepost. Important features of the model are: (1) That it be useable with any equation of state description of the explosive product gases including both JWL and LEOS table forms. (2) That it exhibits the desired dependence on zone size. We believe that the model described

  20. Effects of temperature, humidity, sample geometry, and other variables on Bruceton type 12 impact initiation of HMX-based high explosives

    SciTech Connect

    Avilucea, Gabriel R; Aragon, Daniel J; Peterson, Paul D; Preston, Daniel N; Hartline, Ernest L; Hagelberg, Stephanie I

    2009-01-01

    The drop weight impact test, developed at Bruceton Naval Research Laboratory 60 years ago, is still the most commonly used configuration for evaluating sensitivity of explosives to non-shock ignition. The standard drop weight impact test is performed under ambient conditions for temperature and humidity - variations in which are known to significantly affect the probability of reaction. We have performed a series of impact tests in an attempt to characterize the effect of temperature, humidity, sample geometry (height, mass, L/d, and pressed density), sample confinement, and impact surface properties (strength and coefficient of friction) on the probability of reaction in a drop weight impact test. Differences in the probability of reaction have been determined across a range of drop heights for each configuration. The results clearly show significant shifts in the probability of reaction and in the slope of the reaction probability curve for several of the variables.