29 CFR 1918.23 - Jacob's ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... ladder. (d) When a Jacob's ladder is being used so that there is a danger of an employee falling or being... ladders. (a) Jacob's ladders shall be of the double rung or flat tread type. They shall be well maintained... pulled up entirely. (c) When a Jacob's ladder is used as the means of access to a barge being worked...

29 CFR 1917.118 - Fixed ladders.

Code of Federal Regulations, 2014 CFR

2014-07-01

... tubular scaffold framing; and (4) Ladders used only for fire-fighting or emergency purposes. (b... a ladder, including individual rung ladders, permanently attached to a structure, building or piece... walls of the well. (c) Defects. (1) Ladders with broken, split or missing rungs, steps or rails, broken...

29 CFR 1917.118 - Fixed ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... tubular scaffold framing; and (4) Ladders used only for fire-fighting or emergency purposes. (b... a ladder, including individual rung ladders, permanently attached to a structure, building or piece... walls of the well. (c) Defects. (1) Ladders with broken, split or missing rungs, steps or rails, broken...

29 CFR 1917.118 - Fixed ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... tubular scaffold framing; and (4) Ladders used only for fire-fighting or emergency purposes. (b... a ladder, including individual rung ladders, permanently attached to a structure, building or piece... walls of the well. (c) Defects. (1) Ladders with broken, split or missing rungs, steps or rails, broken...

29 CFR 1917.119 - Portable ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MARINE TERMINALS Terminal Facilities § 1917.119 Portable ladders. (a) Scope and applicability... Requirements for Portable Reinforced Plastic Ladders (d) Standards for job-made portable ladders. Job-made...

29 CFR 1915.72 - Ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

...). (b) Construction of portable wood cleated ladders up to 30 feet in length. (1) Wood side rails shall... shall be at least 25/32×33/4 inches in cross section. (c) Construction of portable wood cleated ladders... split side rails, or other faulty or defective construction is prohibited. When ladders with such...

29 CFR 1926.1053 - Ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... plastic ladder shall sustain at least 3.3 times the maximum intended load. The ability of a ladder to... that each extra-heavy-duty type 1A metal or plastic ladders shall sustain at least 3.3 times the... parapet is cut to permit passage through the parapet; if the parapet is continuous, the access level shall...

A silicon technology for millimeter-wave monolithic circuits

NASA Astrophysics Data System (ADS)

Stabile, P. J.; Rosen, A.

1984-12-01

A silicon millimeter-wave integrated-circuit (SIMMWIC) technology that includes high-energy ion implantation and pulsed-laser annealing, secondary ion mass spectrometry (SIMS) profile diagnostics, and novel wafer thinning has been developed. This technology has been applied to a SIMMWIC single-pole single-throw (SPST) switch and to IMPATT and p-i-n diode fabrication schemes. Thus, the SIMMWIC technology is a proven base for monolithic millimeter-wave sources and control circuit applications.

46 CFR 108.160 - Vertical ladders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Construction and Arrangement Means of Escape § 108.160 Vertical ladders. (a) Each vertical ladder must have... vertical fixed ladders may be made of wood. [CGD 73-251, 43 FR 56808, Dec. 4, 1978, as amended by USCG-2002...

Chaos in a neural network circuit

NASA Astrophysics Data System (ADS)

Kepler, Thomas B.; Datt, Sumeet; Meyer, Robert B.; Abott, L. F.

1990-12-01

We have constructed a neural network circuit of four clipped, high-grain, integrating operational amplifiers coupled to each other through an array of digitally programmable resistor ladders (MDACs). In addition to fixed-point and cyclic behavior, the circuit exhibits chaotic behavior with complex strange attractors which are approached through period doubling, intermittent attractor expansion and/or quasiperiodic pathways. Couplings between the nonlinear circuit elements are controlled by a computer which can automatically search through the space of couplings for interesting phenomena. We report some initial statistical results relating the behavior of the network to properties of its coupling matrix. Through these results and further research the circuit should help resolve fundamental issues concerning chaos in neural networks.

Getting Clever with the Sliding Ladder

ERIC Educational Resources Information Center

De, Subhranil

2014-01-01

The familiar system involving a uniform ladder sliding against a vertical wall and a horizontal floor is considered again. The floor is taken to be smooth and the wall to be possibly rough--a situation where no matter how large the static friction coefficient between the ladder and the wall, the ladder cannot lean at rest and must slide down.…

30 CFR 56.11006 - Fixed ladder landings.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fixed ladder landings. 56.11006 Section 56....11006 Fixed ladder landings. Fixed ladders shall project at least 3 feet above landings, or subtantial handholds shall be provided above the landings. ...

30 CFR 56.11006 - Fixed ladder landings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fixed ladder landings. 56.11006 Section 56....11006 Fixed ladder landings. Fixed ladders shall project at least 3 feet above landings, or subtantial handholds shall be provided above the landings. ...

29 CFR 1910.25 - Portable wood ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.25 Portable wood ladders. (a... safety under normal conditions of usage. Other types of special ladders, fruitpicker's ladders...

GaAs VLSI technology and circuit elements for DSP

NASA Astrophysics Data System (ADS)

Mikkelson, James M.

1990-10-01

Recent progress in digital GaAs circuit performance and complexity is presented to demonstrate the current capabilities of GaAs components. High density GaAs process technology and circuit design techniques are described and critical issues for achieving favorable complexity speed power and cost tradeoffs are reviewed. Some DSP building blocks are described to provide examples of what types of DSP systems could be implemented with present GaAs technology. DIGITAL GaAs CIRCUIT CAPABILITIES In the past few years the capabilities of digital GaAs circuits have dramatically increased to the VLSI level. Major gains in circuit complexity and power-delay products have been achieved by the use of silicon-like process technologies and simple circuit topologies. The very high speed and low power consumption of digital GaAs VLSI circuits have made GaAs a desirable alternative to high performance silicon in hardware intensive high speed system applications. An example of the performance and integration complexity available with GaAs VLSI circuits is the 64x64 crosspoint switch shown in figure 1. This switch which is the most complex GaAs circuit currently available is designed on a 30 gate GaAs gate array. It operates at 200 MHz and dissipates only 8 watts of power. The reasons for increasing the level of integration of GaAs circuits are similar to the reasons for the continued increase of silicon circuit complexity. The market factors driving GaAs VLSI are system design methodology system cost power and reliability. System designers are hesitant or unwilling to go backwards to previous design techniques and lower levels of integration. A more highly integrated system in a lower performance technology can often approach the performance of a system in a higher performance technology at a lower level of integration. Higher levels of integration also lower the system component count which reduces the system cost size and power consumption while improving the system reliability

Logic Circuits as a Vehicle for Technological Literacy.

ERIC Educational Resources Information Center

Hazeltine, Barrett

1985-01-01

Provides basic information on logic circuits, points out that the topic is a good vehicle for developing technological literacy. The subject could be included in such courses as philosophy, computer science, communications, as well as in courses dealing with electronic circuits. (JN)

The reconstructive microsurgery ladder in orthopaedics.

PubMed

Tintle, Scott M; Levin, L Scott

2013-03-01

Since the advent of the operating microscope by Julius Jacobson in 1960, reconstructive microsurgery has become an integral part of extremity reconstruction and orthopaedics. During World War I, with the influx of severe extremity trauma Harold Gillies introduced the concept of the reconstructive ladder for wound closure. The concept of the reconstructive ladder goes from simple to complex means of attaining wound closure. Over the last half century microsurgery has continued to evolve and progress. We now have a microsurgical reconstructive ladder. The microsurgical reconstruction ladder is based upon the early work on revascularization and replantation extending through the procedures that are described in this article. Copyright © 2013. Published by Elsevier Ltd.

30 CFR 57.11006 - Fixed ladder landings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fixed ladder landings. 57.11006 Section 57... Escapeways Travelways-Surface and Underground § 57.11006 Fixed ladder landings. Fixed ladders shall project at least 3 feet above landings, or substantial handholds shall be provided above the landings. ...

30 CFR 57.11006 - Fixed ladder landings.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fixed ladder landings. 57.11006 Section 57... Escapeways Travelways-Surface and Underground § 57.11006 Fixed ladder landings. Fixed ladders shall project at least 3 feet above landings, or substantial handholds shall be provided above the landings. ...

46 CFR 108.167 - Weather deck ladders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Weather deck ladders. 108.167 Section 108.167 Shipping... EQUIPMENT Construction and Arrangement Means of Escape § 108.167 Weather deck ladders. Each unit must have at least one permanent, inclined ladder between each weather deck. Classified Locations ...

46 CFR 108.167 - Weather deck ladders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Weather deck ladders. 108.167 Section 108.167 Shipping... EQUIPMENT Construction and Arrangement Means of Escape § 108.167 Weather deck ladders. Each unit must have at least one permanent, inclined ladder between each weather deck. Classified Locations ...

46 CFR 108.167 - Weather deck ladders.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Weather deck ladders. 108.167 Section 108.167 Shipping... EQUIPMENT Construction and Arrangement Means of Escape § 108.167 Weather deck ladders. Each unit must have at least one permanent, inclined ladder between each weather deck. Classified Locations ...

46 CFR 108.167 - Weather deck ladders.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Weather deck ladders. 108.167 Section 108.167 Shipping... EQUIPMENT Construction and Arrangement Means of Escape § 108.167 Weather deck ladders. Each unit must have at least one permanent, inclined ladder between each weather deck. Classified Locations ...

46 CFR 108.167 - Weather deck ladders.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Weather deck ladders. 108.167 Section 108.167 Shipping... EQUIPMENT Construction and Arrangement Means of Escape § 108.167 Weather deck ladders. Each unit must have at least one permanent, inclined ladder between each weather deck. Classified Locations ...

29 CFR 1910.25 - Portable wood ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 5 2013-07-01 2013-07-01 false Portable wood ladders. 1910.25 Section 1910.25 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.25 Portable wood ladders. (a... for the construction, care, and use of the common types of portable wood ladders, in order to insure...

29 CFR 1910.25 - Portable wood ladders.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 5 2014-07-01 2014-07-01 false Portable wood ladders. 1910.25 Section 1910.25 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.25 Portable wood ladders. (a... for the construction, care, and use of the common types of portable wood ladders, in order to insure...

Climbing the Ladder: Experience with Developing a Large Group Genetic Counselor Career Ladder at Children's National Health System.

PubMed

Kofman, Laura; Seprish, Mary Beth; Summar, Marshall

2016-08-01

Children's National Health System (CNHS) is a not-for-profit pediatric hospital that employs around twenty genetic counselors in a range of specialties, including clinical pediatric, neurology, fetal medicine, research, and laboratory. CNHS lacked a structured system of advancement for their genetic counselors; therefore, a formal career ladder was proposed by the genetic counselors based on years of experience, responsibility, and job performance. This career ladder utilized monetary, academic, and seniority incentives to encourage advancement and continue employment at CNHS. The creation and ultimate approval of the career ladder required direct input from genetic counselors, Department Chairs, and Human Resource personnel. The establishment of a genetic counselor career ladder at CNHS will hopefully benefit the profession of genetic counselors as a whole and allow other facilities to create and maintain their own career ladder to meet the needs of the growing, competitive, field of genetic counseling.

29 CFR 1926.1053 - Ladders.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders § 1926.1053 Ladders. Link to an... structural defects, such as, but not limited to, broken or missing rungs, cleats, or steps, broken or split..., such as, but not limited to, broken or missing rungs, cleats, or steps, broken or split rails, or...

Latest Trends of Vacuum Circuit Breaker and Related Technologies

NASA Astrophysics Data System (ADS)

Kozono, Hideaki; Tanimizu, Toru

Vacuum Circuit Breakers (VCBs) have been widely used for medium voltage level, because of their performance: compact size, light weight, maintenance free operations and environment-friendly characteristics. They become most comfortable breakers for our needs from other breakers: oil, air, magnetic blast and gas. In this paper the history of vacuum, and latest trends of circuit breakers and related technologies are described, as well as merits or demerits of using vacuum technologies.

Perspective on rainbow-ladder truncation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eichmann, G.; Institut fuer Physik, Karl-Franzens-Universitaet Graz, A-8010 Graz; Alkofer, R.

2008-04-15

Prima facie the systematic implementation of corrections to the rainbow-ladder truncation of QCD's Dyson-Schwinger equations will uniformly reduce in magnitude those calculated mass-dimensioned results for pseudoscalar and vector meson properties that are not tightly constrained by symmetries. The aim and interpretation of studies employing rainbow-ladder truncation are reconsidered in this light.

Perspective on rainbow-ladder truncation

NASA Astrophysics Data System (ADS)

Eichmann, G.; Alkofer, R.; Cloët, I. C.; Krassnigg, A.; Roberts, C. D.

2008-04-01

Prima facie the systematic implementation of corrections to the rainbow-ladder truncation of QCD's Dyson-Schwinger equations will uniformly reduce in magnitude those calculated mass-dimensioned results for pseudoscalar and vector meson properties that are not tightly constrained by symmetries. The aim and interpretation of studies employing rainbow-ladder truncation are reconsidered in this light.

Monolithic Microwave Integrated Circuits Based on GaAs Mesfet Technology

NASA Astrophysics Data System (ADS)

Bahl, Inder J.

Advanced military microwave systems are demanding increased integration, reliability, radiation hardness, compact size and lower cost when produced in large volume, whereas the microwave commercial market, including wireless communications, mandates low cost circuits. Monolithic Microwave Integrated Circuit (MMIC) technology provides an economically viable approach to meeting these needs. In this paper the design considerations for several types of MMICs and their performance status are presented. Multifunction integrated circuits that advance the MMIC technology are described, including integrated microwave/digital functions and a highly integrated transceiver at C-band.

29 CFR 1926.1053 - Ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... spreader or locking device shall be provided on each stepladder to hold the front and back sections in an... ascend or descend without continually having to hold, push or pull any part of the device, leaving both... degrees from the horizontal, as measured to the back side of the ladder. (6) Ladders shall be used only on...

Passage and behaviour of cultured Lake Sturgeon in a prototype side-baffle fish ladder: I. Ladder hydraulics and fish ascent

USGS Publications Warehouse

Kynard, B.; Pugh, D.; Parker, T.

2011-01-01

Research and development of a fish ladder for sturgeons requires understanding ladder hydraulics and sturgeon behaviour in the ladder to insure the ladder is safe and provides effective passage. After years of research and development, we designed and constructed a full-scale prototype side-baffle ladder inside a spiral flume (38.3m long??1m wide??1m high) on a 6% (1:16.5) slope with a 1.92-m rise in elevation (bottom to top) to test use by sturgeons. Twenty-eight triangular side baffles, each extending part way across the flume, alternated from inside wall to outside wall down the ladder creating two major flow habitats: a continuous, sinusoidal flow down the ladder through the vertical openings of side-baffles and an eddy below each side baffle. Ascent and behaviour was observed on 22 cultured Lake Sturgeon=LS (Acipenser fulvescens) repeatedly tested in groups as juveniles (as small as 105.1cm TL, mean) or as adults (mean TL, 118cm) during four periods (fall 2002 and 2003; spring 2003 and 2007). Percent of juveniles entering the ladder that ascended to the top was greater in spring (72.7%) than in fall (40.9-45.5%) and 90.9% of 11 adults, which ascended as juveniles, ascended to the top. Six LS (27.3%) never swam to the top and seven (31.8%) swam to the top in all tests, indicating great variability among individuals for ascent drive. Some LS swam directly to the top in <1min, but most rested in an eddy during ascent. Juveniles swimming through outside wall baffle slots (mean velocity, 1.2ms-1) swam at 1.8-2.2body lengthss-1 and 3.2-3.3tail beatss-1, either at or approaching prolonged swimming speed. The side-baffle ladder was stream-like and provided key factors for a sturgeon ladder: a continuous flow and no full cross-channel walls, abundant eddies for resting, an acceptable water depth, and a water velocity fish could ascend swimming 2bls-1. A side-baffle ladder passes LS and other moderate-swimming fishes. ?? 2011 Blackwell Verlag, Berlin.

Career ladder program for registered nurses in ambulatory care.

PubMed

Nelson, Joan; Sassaman, Becky; Phillips, Alison

2008-01-01

RN ladder programs are designed to inspire and reward clinical excellence. Kaiser Permanente Colorado's (KPCO) career ladder program emerged as a result of a labor-management partnership. Career ladder point assignments are reflective of the organization's priorities and values. KPCO's career ladder point tool awards RNs for formal and continuing education, professional presentations, organizational experience and experience as an RN, certifications and active professional memberships, leadership activities, research and publications, and nursing-related volunteer work. Participation in the RN career ladder requires that the nurse achieve a self-determined, manager-approved, measurable goal that will improve patient care. Career ladder nurses at KPCO were significantly more involved in leadership and interdisciplinary activities, quality improvement projects, and preceptorship.

Effects of ladder parameters on asymmetric patterns of force exertion during below-knee amputees climbing ladders.

PubMed

Li, Weidong; Li, Shiqi; Fu, Yan; Chen, Jacon

2017-03-01

Different from walking, ladder climbing requires four-limb coordination and more energy exertion for below-knee amputees (BKAs). We hypothesized that functional deficiency of a disabled limb shall be compensated by the other three intact limbs, showing an asymmetry pattern among limbs. Hand and foot forces of six below-knee amputees and six able-bodied people were collected. Hand, foot and hand/foot sum force variances between groups (non-BKA, intact side and prosthetic side) were carefully examined. Our hypothesis was validated that there is asymmetry between prosthetic and intact side. Results further showed that the ipsilateral hand of the prosthetic leg is stronger than the hand on the intact side, compensating weakness of the prosthetic leg. Effects of ladder rung separations and ladder slant on asymmetric force distribution of BKAs were evaluated, indicating that rung separation has a more significant interactive effect on hand/foot force of BKAs than ladder slant.

[Flexible print circuit technology application in biomedical engineering].

PubMed

Jiang, Lihua; Cao, Yi; Zheng, Xiaolin

2013-06-01

Flexible print circuit (FPC) technology has been widely applied in variety of electric circuits with high precision due to its advantages, such as low-cost, high specific fabrication ability, and good flexibility, etc. Recently, this technology has also been used in biomedical engineering, especially in the development of microfluidic chip and microelectrode array. The high specific fabrication can help making microelectrode and other micro-structure equipment. And good flexibility allows the micro devices based on FPC technique to be easily packaged with other parts. In addition, it also reduces the damage of microelectrodes to the tissue. In this paper, the application of FPC technology in biomedical engineering is introduced. Moreover, the important parameters of FPC technique and the development trend of prosperous applications is also discussed.

29 CFR 1910.27 - Fixed ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.27 Fixed ladders. (a) Design... fraction thereof, except that, where no cage, well, or ladder safety device is provided, landing platforms...

Technology CAD for integrated circuit fabrication technology development and technology transfer

NASA Astrophysics Data System (ADS)

Saha, Samar

2003-07-01

In this paper systematic simulation-based methodologies for integrated circuit (IC) manufacturing technology development and technology transfer are presented. In technology development, technology computer-aided design (TCAD) tools are used to optimize the device and process parameters to develop a new generation of IC manufacturing technology by reverse engineering from the target product specifications. While in technology transfer to manufacturing co-location, TCAD is used for process centering with respect to high-volume manufacturing equipment of the target manufacturing equipment of the target manufacturing facility. A quantitative model is developed to demonstrate the potential benefits of the simulation-based methodology in reducing the cycle time and cost of typical technology development and technology transfer projects over the traditional practices. The strategy for predictive simulation to improve the effectiveness of a TCAD-based project, is also discussed.

A clinical ladder for occupational health nurses.

PubMed

Lang, Yolanda C

2010-06-01

Occupational health nurses must have a growing, expanding knowledge base to remain current in practice. The American Board for Occupational Health Nurses, Inc. encourages advancement with the availability of certification examinations. Health care centers support clinical advancement programs for bedside nurses. Nurses who continue their education either through a degree program or via continuing education or certification advance up the clinical ladder, receiving a higher salary, recognition from their peers, and perhaps even financial assistance to continue climbing, yet occupational health nurses do not have their own clinical advancement ladder. This article examines the steps necessary to develop a clinical ladder and presents a clinical ladder specific to occupational health nursing developed by the author. Copyright 2010, SLACK Incorporated.

Careers Under Construction: Models for Developing Career Ladders.

ERIC Educational Resources Information Center

2003

This publication describes resources and processes that are a catalyst for discussion and action for local workforce investment partners--employers, training providers, and workers--to plan and implement regional career ladder programs. Section 1 discusses career ladders and uses. Section 2 describes how to build an industry career ladder or…

Edge currents in frustrated Josephson junction ladders

NASA Astrophysics Data System (ADS)

Marques, A. M.; Santos, F. D. R.; Dias, R. G.

2016-09-01

We present a numerical study of quasi-1D frustrated Josephson junction ladders with diagonal couplings and open boundary conditions, in the large capacitance limit. We derive a correspondence between the energy of this Josephson junction ladder and the expectation value of the Hamiltonian of an analogous tight-binding model, and show how the overall superconducting state of the chain is equivalent to the minimum energy state of the tight-binding model in the subspace of one-particle states with uniform density. To satisfy the constraint of uniform density, the superconducting state of the ladder is written as a linear combination of the allowed k-states of the tight-binding model with open boundaries. Above a critical value of the parameter t (ratio between the intra-rung and inter-rung Josephson couplings) the ladder spontaneously develops currents at the edges, which spread to the bulk as t is increased until complete coverage is reached. Above a certain value of t, which varies with ladder size (t = 1 for an infinite-sized ladder), the edge currents are destroyed. The value t = 1 corresponds, in the tight-binding model, to the opening of a gap between two bands. We argue that the disappearance of the edge currents with this gap opening is not coincidental, and that this points to a topological origin for these edge current states.

Dental Laboratory Career Ladder AFS 982X0.

DTIC Science & Technology

1982-09-01

7ADA120 102 AIR FORCE OCCUPATIONAL MEASUREMENT CENTER RANDOLPH AFB TX F/6 Ri9 DENTAL LABORATORY CAREER LADDER AFS 982XO.(U) UNCLASSIFIED NLEEEili E...Eli E~lllllllllEEE EEEEEIIIEEEEEE EIEEEEIIEEEEEE IIIIIIIIIIIIIIlLZ UNITED STATES AIR FORCE 0! DENTAL LABORATORY CAREER LADDER DTlC AFS 982X0 ELEr.L_...LADDER STRUCTURE GROUPS ----------------------------------- 57 APPENDIX B - JOB DESCRIPTIONS FOR BASE AND AREA DENTAL LABORATORY PERSONNEL

Modeling the Sliding/Falling Ladder Paradox

ERIC Educational Resources Information Center

Fox, William P.; Fox, James B.

2003-01-01

Recently we were presented with an interesting twist to the sliding ladder problem viewed in the related rates section of most calculus textbooks. Our problem concerning a sliding ladder that eventually hits the ground. At first, those attempting this problem fell into the calculus trap using only related rates. Previous work for this problem…

Ladder-structured photonic variable delay device

NASA Technical Reports Server (NTRS)

Yao, X. Steve (Inventor)

1998-01-01

An ladder-structured variable delay device for providing variable true time delay to multiple optical beams simultaneously. The device comprises multiple basic units stacked on top of each other resembling a ladder. Each basic unit comprises a polarization sensitive corner reflector formed by two polarization beamsplitters and a polarization rotator array placed parallel to the hypotenuse of the corner reflector. Controlling an array element of the polarization rotator array causes an optical beam passing through the array element to either go up to a basic unit above it or reflect back towards output. The beams going higher on the ladder experience longer optical path delay. Finally, the ladder-structured variable device can be cascaded with another multi-channel delay device to form a new device which combines the advantages of the two individual devices. This programmable optic device has the properties of high packing density, low loss, easy fabrication, and virtually infinite bandwidth. In addition, the delay is reversible so that the same delay device can be used for both antenna transmitting and receiving.

5 CFR 335.104 - Eligibility for career ladder promotion.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Eligibility for career ladder promotion... REGULATIONS PROMOTION AND INTERNAL PLACEMENT General Provisions § 335.104 Eligibility for career ladder promotion. No employee shall receive a career ladder promotion unless his or her current rating of record...

Giant Stark effect in double-stranded porphyrin ladder polymers

NASA Astrophysics Data System (ADS)

Pramanik, Anup; Kang, Hong Seok

2011-03-01

Using the first-principles calculations, we have investigated the stability and the electronic structure of two types of recently synthesized one-dimensional nanoribbons, i.e., double-stranded zinc(II) porphyrin ladder polymer (LADDER) arrays. First, electronic structure calculations were used to show that the LADDER is a semiconductor. Most importantly, the application of a transverse electric field significantly reduces the band gap of the LADDER, ultimately converting the LADDER to a metal at a field strength of 0.1 V/Å. The giant Stark effect in this case is almost as strong as that in boron nitride nanotubes and nanoribbons. In the presence of an electric field, hole conduction and electronic conduction will occur entirely through spatially separated strands, rendering these materials useful for nanoelectronic devices. Second, the substitution of hydrogen atoms in the porphyrin units or that of zinc ions with other kinds of chemical species is found to increase the binding strength of the LADDER and reduce the band gap.

46 CFR 190.10-15 - Vertical ladders not accepted.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Vertical ladders not accepted. 190.10-15 Section 190.10-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS CONSTRUCTION AND ARRANGEMENT Means of Escape § 190.10-15 Vertical ladders not accepted. (a) Vertical ladders...

Instabilities of coupled Cu2O5 ladders

NASA Astrophysics Data System (ADS)

Schuetz, Florian; Marston, Brad

2008-03-01

The spin-ladder compound Sr14-xCaxCu24O41 has a complex phase diagram including charge-density-wave order as well as unconventional superconductivity under high pressure. Due to its quasi-one-dimensional natureootnotetextS. Lee, J. B. Marston, J. O. Fjaerestad, Phys. Rev. B 72, 075126. fundamental questions about the high-Tc cuprates might be more easily addressed in this context. However, due to the spatial proximity of neighboring ladders inter-ladder Coulomb repulsion as well as hopping between ladders might still be important. Using the functional renormalization groupootnotetextM. Salmhofer and C. Honerkamp, Prog. Theor. Physics 105, 1 (2001). and an analysis of generalized susceptibilities ootnotetextD. Zanchi and H. J. Schulz, Phys. Rev. B 61, 13609 (2000); C. J. Halboth and W. Metzner, Phys. Rev. Lett. 85, 5162 (2000)., we study a model of coupled Cu2O5 ladders ootnotetextK. Wohlfeld, A. M. Oles, and G. A. Sawatzky, Phys. Rev. B 75, 180501(R) (2007).. We investigate instabilities towards charge, spin, and pairing order as a function of hole doping, inter-ladder hopping, and interaction strength starting from experimentally relevant hopping parametersootnotetextT. F. A. Müller, et al., Phys. Rev. B 57, R12655 (1998)..

Ladder polymers for use as high temperature stable resins or coatings

NASA Technical Reports Server (NTRS)

Meador, Mary Ann (Inventor)

1990-01-01

An object of the invention is to synthesize a new class of ladder and partial ladder polymers. In accordance with the invention, the new class of ladder and partial ladder polymers are synthesized by polymerizing a bis-dienophile with a bis-diene. Another object of the invention is to provide a fabricated, electrically conducting, void free composite comprising the new class of the ladder and partial ladder polymers described above. The novelty of the invention relates to a new class of ladder and partial ladder polymers and a process for synthesizing these polymers. These polymers are soluble in common organic solvents and are characterized with a unique dehydration property at temperatures of 300 to 400 C to provide thermo-oxidatively stable pentiptycene units along the polymeric backbone. These polymers are further characterized with high softening points and good thermo-oxidative stability properties. Thus these polymers have potential as processable, matrix resins for high temperature composite applications.

Smart Power: New power integrated circuit technologies and their applications

NASA Astrophysics Data System (ADS)

Kuivalainen, Pekka; Pohjonen, Helena; Yli-Pietilae, Timo; Lenkkeri, Jaakko

1992-05-01

Power Integrated Circuits (PIC) is one of the most rapidly growing branches of the semiconductor technology. The PIC markets has been forecast to grow from 660 million dollars in 1990 to 1658 million dollars in 1994. It has even been forecast that at the end of the 1990's the PIC markets would correspond to the value of the whole semiconductor production in 1990. Automotive electronics will play the leading role in the development of the standard PIC's. Integrated motor drivers (36 V/4 A), smart integrated switches (60 V/30 A), solenoid drivers, integrated switch-mode power supplies and regulators are the latest standard devices of the PIC manufactures. ASIC (Application Specific Integrated Circuits) PIC solutions are needed for the same reasons as other ASIC devices: there are no proper standard devices, a company has a lot of application knowhow, which should be kept inside the company, the size of the product must be reduced, and assembly costs are wished to be reduced by decreasing the number of discrete devices. During the next few years the most probable ASIC PIC applications in Finland will be integrated solenoid and motor drivers, an integrated electronic lamp ballast circuit and various sensor interface circuits. Application of the PIC technologies to machines and actuators will strongly be increased all over the world. This means that various PIC's, either standard PIC's or full custom ASIC circuits, will appear in many products which compete with the corresponding Finnish products. Therefore the development of the PIC technologies must be followed carefully in order to immediately be able to apply the latest development in the smart power technologies and their design methods.

Quantifying Ladder Fuels: A New Approach Using LiDAR

Treesearch

Heather Kramer; Brandon Collins; Maggi Kelly; Scott Stephens

2014-01-01

We investigated the relationship between LiDAR and ladder fuels in the northern Sierra Nevada, California USA. Ladder fuels are often targeted in hazardous fuel reduction treatments due to their role in propagating fire from the forest floor to tree crowns. Despite their importance, ladder fuels are difficult to quantify. One common approach is to calculate canopy base...

29 CFR Appendix A to Subpart X of... - Ladders

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 8 2013-07-01 2013-07-01 false Ladders A Appendix A to Subpart X of Part 1926 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders Pt. 1926, Subpt. X, App. A Appendix A to Subpart X of Part 1926—Ladders This appendix serves as a non-mandatory guideline to assist...

29 CFR Appendix A to Subpart X of... - Ladders

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Ladders A Appendix A to Subpart X of Part 1926 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders Pt. 1926, Subpt. X, App. A Appendix A to Subpart X of Part 1926—Ladders This appendix serves as a non-mandatory guideline to assist...

29 CFR Appendix A to Subpart X of... - Ladders

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Ladders A Appendix A to Subpart X of Part 1926 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders Pt. 1926, Subpt. X, App. A Appendix A to Subpart X of Part 1926—Ladders This appendix serves as a non-mandatory guideline to assist...

29 CFR Appendix A to Subpart X of... - Ladders

Code of Federal Regulations, 2010 CFR

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Ladders A Appendix A to Subpart X of Part 1926 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders Pt. 1926, Subpt. X, App. A Appendix A to Subpart X of Part 1926—Ladders This appendix serves as a non-mandatory guideline to assist...

29 CFR Appendix A to Subpart X of... - Ladders

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Ladders A Appendix A to Subpart X of Part 1926 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Stairways and Ladders Pt. 1926, Subpt. X, App. A Appendix A to Subpart X of Part 1926—Ladders This appendix serves as a non-mandatory guideline to assist...

Gluing Ladder Feynman Diagrams into Fishnets

DOE PAGES

Basso, Benjamin; Dixon, Lance J.

2017-08-14

We use integrability at weak coupling to compute fishnet diagrams for four-point correlation functions in planar Φ 4 theory. Our results are always multilinear combinations of ladder integrals, which are in turn built out of classical polylogarithms. The Steinmann relations provide a powerful constraint on such linear combinations, which leads to a natural conjecture for any fishnet diagram as the determinant of a matrix of ladder integrals.

Combining a clinical ladder and performance appraisal system as a reward strategy: the EXCEL clinical ladder program.

PubMed

Moe, J K; Lonowski, L R; Yancer, D A

1994-09-01

In response to the dramatic changes occurring in health care today and a desire to reward professional nurses for clinical behaviors that would be valued in the future, Bergan Mercy Medical Center (BMMC) has developed an innovative clinical ladder/performance appraisal system. The BMMC EXCEL Clinical Ladder program, which is based on the developmental model of Patricia Benner, is a competency-based system that uniquely combines a clinical ladder and performance appraisal system. The program is clinically focused and contains optional components in which registered nurses (RNs) can receive additional credit for participation in professional growth and leadership activities. Nurses document examples of their practice through nursing narratives that describe actual clinical situations. The development and implementation processes, challenges encountered, and recommendations for alternative approaches to the implementation of such a unique system are discussed.

Monolithic Microwave Integrated Circuit (MMIC) technology for space communications applications

NASA Technical Reports Server (NTRS)

Connolly, Denis J.; Bhasin, Kul B.; Romanofsky, Robert R.

1987-01-01

Future communications satellites are likely to use gallium arsenide (GaAs) monolithic microwave integrated-circuit (MMIC) technology in most, if not all, communications payload subsystems. Multiple-scanning-beam antenna systems are expected to use GaAs MMIC's to increase functional capability, to reduce volume, weight, and cost, and to greatly improve system reliability. RF and IF matrix switch technology based on GaAs MMIC's is also being developed for these reasons. MMIC technology, including gigabit-rate GaAs digital integrated circuits, offers substantial advantages in power consumption and weight over silicon technologies for high-throughput, on-board baseband processor systems. For the more distant future pseudomorphic indium gallium arsenide (InGaAs) and other advanced III-V materials offer the possibility of MMIC subsystems well up into the millimeter wavelength region. All of these technology elements are in NASA's MMIC program. Their status is reviewed.

Monolithic Microwave Integrated Circuit (MMIC) technology for space communications applications

NASA Technical Reports Server (NTRS)

Connolly, Denis J.; Bhasin, Kul B.; Romanofsky, Robert R.

1987-01-01

Future communications satellites are likely to use gallium arsenide (GaAs) monolithic microwave integrated-circuit (MMIC) technology in most, if not all, communications payload subsystems. Multiple-scanning-beam antenna systems are expected to use GaAs MMICs to increase functional capability, to reduce volume, weight, and cost, and to greatly improve system reliability. RF and IF matrix switch technology based on GaAs MMICs is also being developed for these reasons. MMIC technology, including gigabit-rate GaAs digital integrated circuits, offers substantial advantages in power consumption and weight over silicon technologies for high-throughput, on-board baseband processor systems. For the more distant future pseudomorphic indium gallium arsenide (InGaAs) and other advanced III-V materials offer the possibility of MMIC subsystems well up into the millimeter wavelength region. All of these technology elements are in NASA's MMIC program. Their status is reviewed.

30 CFR 56.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Fixed ladder anchorage and toe clearance. 56.11005 Section 56.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Travelways § 56.11005 Fixed ladder anchorage and toe clearance. Fixed ladders shall be anchored securely and...

30 CFR 56.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fixed ladder anchorage and toe clearance. 56.11005 Section 56.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Travelways § 56.11005 Fixed ladder anchorage and toe clearance. Fixed ladders shall be anchored securely and...

30 CFR 56.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fixed ladder anchorage and toe clearance. 56.11005 Section 56.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Travelways § 56.11005 Fixed ladder anchorage and toe clearance. Fixed ladders shall be anchored securely and...

30 CFR 56.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fixed ladder anchorage and toe clearance. 56.11005 Section 56.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Travelways § 56.11005 Fixed ladder anchorage and toe clearance. Fixed ladders shall be anchored securely and...

30 CFR 56.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fixed ladder anchorage and toe clearance. 56.11005 Section 56.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Travelways § 56.11005 Fixed ladder anchorage and toe clearance. Fixed ladders shall be anchored securely and...

The one step fermionic ladder

NASA Astrophysics Data System (ADS)

Das, Joy Prakash; Setlur, Girish S.

2017-10-01

The one step fermionic ladder refers to two parallel Luttinger Liquids (poles of the ladder) placed such that there is a finite probability of electrons hopping between the two poles at a pair of opposing points along each of the poles. The many-body Green function for such a system is calculated in presence of forward scattering interactions using the powerful non-chiral bosonization technique (NCBT). This technique is based on a non-standard harmonic analysis of the rapidly varying parts of the density fields appropriate for the study of strongly inhomogeneous ladder systems. The closed analytical expression for the correlation function obtained from NCBT is nothing but the series involving the RPA (Random Phase Approximation) diagrams in powers of the forward scattering coupling strength resummed to include only the most singular terms with the source of inhomogeneities treated exactly. Finally the correlation functions are used to study physical phenomena such as Friedel oscillations and the conductance of such systems with the potential difference applied across various ends.

Work-related ladder fall fractures: identification and diagnosis validation using narrative text.

PubMed

Smith, Gordon S; Timmons, Robert A; Lombardi, David A; Mamidi, Dheeresh K; Matz, Simon; Courtney, Theodore K; Perry, Melissa J

2006-09-01

To identify ladder-related fracture injuries and determine how ladder fall fractures differ from other ladder-related injuries. Ladder-related fracture cases were identified using narrative text and coded data from workers' compensation claims. Potential cases were identified by text searches and verified with claim records. Injury characteristics were compared using proportionate injury ratios. Of 9826 ladder-related injuries, 7% resulted in fracture cases. Falls caused 89% of fractures and resulted in more medical costs and disability days than other injuries. Frequent mechanisms were ladder instability (22%) and lost footing (22%). Narrative text searches identified 17% more fractures than injury codes alone. Males were more likely to sustain a fall fracture than other injuries; construction workers were most likely, and retail workers were the least likely to sustain fractures. Fractures are an important injury from ladder falls, resulting more serious consequences than other ladder-related injuries. Text analysis can improve the quality and utility of workers compensation data by identifying and understanding injury causes. Proportionate injury ratios are also useful for making cross-group comparisons of injury experience when denominator data are not available. Greater attention to risk factors for ladder falls is needed for targeting interventions.

A balanced intervention ladder: promoting autonomy through public health action.

PubMed

Griffiths, P E; West, C

2015-08-01

The widely cited Nuffield Council on Bioethics 'Intervention Ladder' structurally embodies the assumption that personal autonomy is maximized by non-intervention. Consequently, the Intervention Ladder encourages an extreme 'negative liberty' view of autonomy. Yet there are several alternative accounts of autonomy that are both arguably superior as accounts of autonomy and better suited to the issues facing public health ethics. We propose to replace the one-sided ladder, which has any intervention coming at a cost to autonomy, with a two-sided 'Balanced Intervention Ladder,' where intervention can either enhance or diminish autonomy. We show that not only the alternative, richer accounts of autonomy but even Mill's classic version of negative liberty puts some interventions on the positive side of the ladder. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Revisiting the Ladder on a Wall Problem

ERIC Educational Resources Information Center

Salu, Yehuda

2011-01-01

The problem of a ladder leaning on a wall has been a staple of introductory physics for years. It is discussed in numerous physics textbooks and in journals. Now, it even has an Internet presence. Postings from students seek help for "ladder on a wall" problems. A quick review of those postings would show that they all deal with frictionless…

Designing and Implementing Performance-Based Career Ladder Plans.

ERIC Educational Resources Information Center

Hawley, Willis D.

1985-01-01

Reviews the factors that any teacher motivation plan must incorporate to be effective and outlines 11 principles that should be followed in designing career ladder plans to meet teacher needs, increase teacher competence, and facilitate effective instruction. Warns against potential pitfalls in career ladder plans. (PGD)

Electronic circuits and systems: A compilation. [including integrated circuits, logic circuits, varactor diode circuits, low pass filters, and optical equipment circuits

NASA Technical Reports Server (NTRS)

1975-01-01

Technological information is presented electronic circuits and systems which have potential utility outside the aerospace community. Topics discussed include circuit components such as filters, converters, and integrators, circuits designed for use with specific equipment or systems, and circuits designed primarily for use with optical equipment or displays.

BiCMOS circuit technology for a 704 MHz ATM switch LSI

NASA Astrophysics Data System (ADS)

Ohtomo, Yusuke; Yasuda, Sadayuki; Togashi, Minoru; Ino, Masayuki; Tanabe, Yasuyuki; Inoue, Jun-Ichi; Nogawa, Masafumi; Hino, Shigeki

1994-05-01

This paper describes BiCMOS level-converter circuits and clock circuits that increase VLSI interface speed to 1 GHz, and their application to a 704 MHz ATM switch LSI. An LSI with high speed interface requires a BiCMOS multiplexer/demultiplexer (MUX/DEMUX) on the chip to reduce internal operation speed. A MUX/DEMUX with minimum power dissipation and a minimum pattern area can be designed using the proposed converter circuits. The converter circuits, using weakly cross-coupled CMOS inverters and a voltage regulator circuit, can convert signal levels between LCML and positive CMOS at a speed of 500 MHz. Data synchronization in the high speed region is ensured by a new BiCMOS clock circuit consisting of a pure ECL path and retiming circuits. The clock circuit reduces the chip latency fluctuation of the clock signal and absorbs the delay difference between the ECL clock and data through the CMOS circuits. A rerouting-Banyan (RRB) ATM switch, employing both the proposed converter circuits and the clock circuits, has been fabricated with 0.5 micron BiCMOS technology. The LSI, composed of CMOS 15 K gate LOGIC, 8 Kb RAM, 1 Kb FIFO and ECL 1.6 K gate LOGIC, achieved an operation speed of 704-MHz with power dissipation of 7.2 W.

Novel Low Loss Wide-Band Multi-Port Integrated Circuit Technology for RF/Microwave Applications

NASA Technical Reports Server (NTRS)

Simons, Rainee N.; Goverdhanam, Kavita; Katehi, Linda P. B.; Burke, Thomas P. (Technical Monitor)

2001-01-01

In this paper, novel low loss, wide-band coplanar stripline technology for radio frequency (RF)/microwave integrated circuits is demonstrated on high resistivity silicon wafer. In particular, the fabrication process for the deposition of spin-on-glass (SOG) as a dielectric layer, the etching of microvias for the vertical interconnects, the design methodology for the multiport circuits and their measured/simulated characteristics are graphically illustrated. The study shows that circuits with very low loss, large bandwidth, and compact size are feasible using this technology. This multilayer planar technology has potential to significantly enhance RF/microwave IC performance when combined with semi-conductor devices and microelectromechanical systems (MEMS).

Role of Structural Asymmetry in Controlling Drop Spacing in Microfluidic Ladder Networks

NASA Astrophysics Data System (ADS)

Wang, William; Maddala, Jeevan; Vanapalli, Siva; Rengasamy, Raghunathan

2012-02-01

Manipulation of drop spacing is crucial to many processes in microfluidic devices including drop coalescence, detection and storage. Microfluidic ladder networks ---where two droplet-carrying parallel channels are connected by narrow bypass channels through which the motion of drops is forbidden---have been proposed as a means to control relative separation between pairs of drops. Prior studies in microfluidic ladder networks with vertical bypasses, which possess fore-aft structural symmetry, have revealed that pairs of drops can only undergo reduction in drop spacing at the ladder exit. We investigate the dynamics of drops in microfluidic ladder networks with both vertical and slanted bypasses. Our analytical results indicate that unlike symmetric ladder networks, structural asymmetry introduced by a single slanted bypass can be used to modulate the relative spacing between drops, enabling them to contract, synchronize, expand or even flip at the ladder exit. Our experiments confirm all the behaviors predicted by theory. Numerical analysis further shows that ladders containing several identical bypasses can only linearly transform the input drop spacing. Finally, we find that ladders with specific combinations of vertical and slanted bypasses can generate non-linear transformation of input drop spacing, despite the absence of drop decision-making events at the bypass junctions.

Ladder Climbing and Autoresonant Acceleration of Plasma Waves

NASA Astrophysics Data System (ADS)

Barth, Ido; Dodin, Ilya; Fisch, Nathaniel

2015-11-01

When the background density in a bounded plasma is modulated in time, discrete modes become coupled. Interestingly, for appropriately chosen modulations, the average plasmon energy might be made to grow in a ladder-like manner, achieving up-conversion or down-conversion of the plasmon energy. This reversible process is identified as a classical analog of the effect known as quantum ladder climbing, so that the efficiency and the rate of this process can be written immediately by analogy to a quantum particle in a box. In the limit of densely spaced spectrum, ladder climbing transforms into continuous autoresonance; plasmons may then be manipulated by chirped background modulations much like electrons are autoresonantly manipulated by chirped fields. By formulating the wave dynamics within a universal Lagrangian framework, similar ladder climbing and autoresonance effects are predicted to be achievable with general linear waves in both plasma and other media. Supported by NNSA grant DE274-FG52-08NA28553, DOE contract DE-AC02-09CH11466, and DTRA grant HDTRA1-11-1-0037.

Transferring arbitrary d-dimensional quantum states of a superconducting transmon qudit in circuit QED.

PubMed

Liu, Tong; Su, Qi-Ping; Yang, Jin-Hu; Zhang, Yu; Xiong, Shao-Jie; Liu, Jin-Ming; Yang, Chui-Ping

2017-08-01

A qudit (d-level quantum system) has a large Hilbert space and thus can be used to achieve many quantum information and communication tasks. Here, we propose a method to transfer arbitrary d-dimensional quantum states (known or unknown) between two superconducting transmon qudits coupled to a single cavity. The state transfer can be performed by employing resonant interactions only. In addition, quantum states can be deterministically transferred without measurement. Numerical simulations show that high-fidelity transfer of quantum states between two superconducting transmon qudits (d ≤ 5) is feasible with current circuit QED technology. This proposal is quite general and can be applied to accomplish the same task with natural or artificial atoms of a ladder-type level structure coupled to a cavity or resonator.

Getting to the Bottom of a Ladder Problem

ERIC Educational Resources Information Center

McCartney, Mark

2002-01-01

In this paper, the author introduces a simple problem relating to a pair of ladders. A mathematical model of the problem produces an equation which can be solved in a number of ways using mathematics appropriate to "A" level students or first year undergraduates. The author concludes that the ladder problem can be used in class to develop and…

Allowable bending stresses of wood for use in portable wood ladders

Treesearch

Fred Werren

1975-01-01

A standard for portable wood ladders has been in effect since 1923, and has been revised several times since then. The most recent publication is "American National Standard Safety Standard for Portable Wood Ladders," A14.1-1975, from American National Standards Institute, Inc. Methods of arriving at allowable stresses for wood ladder parts have never been...

Effects of foot placement, hand positioning, age and climbing biodynamics on ladder slip outcomes.

PubMed

Pliner, Erika M; Campbell-Kyureghyan, Naira H; Beschorner, Kurt E

2014-01-01

Ladder falls frequently cause severe injuries; yet the factors that influence ladder slips/falls are not well understood. This study aimed to quantify (1) the effects of restricted foot placement, hand positioning, climbing direction and age on slip outcomes, and (2) differences in climbing styles leading to slips versus styles leading to non-slips. Thirty-two occupational ladder users from three age groups (18-24, 25-44 and 45-64 years) were unexpectedly slipped climbing a vertical ladder, while being assigned to different foot placement conditions (unrestricted vs. restricted toe clearance) and different hand positions (rails vs. rungs). Constraining foot placement increased the climber's likelihood of slipping (p < 0.01), while younger and older participants slipped more than the middle-aged group (p < 0.01). Longer double stance time, dissimilar and more variable foot and body positioning were found in styles leading to a slip. Maintaining sufficient toe clearance and targeting ladder safety training to younger and older workers may reduce ladder falls. Practitioner Summary: Ladder falls frequently cause severe occupational fall injuries. This study aims to identify safer ladder climbing techniques and individuals at risk of falling. The results suggest that ladders with unrestricted toe clearance and ladder climbing training programmes, particularly for younger and older workers, may reduce ladder slipping risk.

Fabrication of multijunction high voltage concentrator solar cells by integrated circuit technology

NASA Technical Reports Server (NTRS)

Valco, G. J.; Kapoor, V. J.; Evans, J. C., Jr.; Chai, A.-T.

1981-01-01

Standard integrated circuit technology has been developed for the design and fabrication of planar multijunction (PMJ) solar cell chips. Each 1 cm x 1 cm solar chip consisted of six n(+)/p, back contacted, internally series interconnected unit cells. These high open circuit voltage solar cells were fabricated on 2 ohm-cm, p-type 75 microns thick, silicon substrates. A five photomask level process employing contact photolithography was used to pattern for boron diffusions, phorphorus diffusions, and contact metallization. Fabricated devices demonstrated an open circuit voltage of 3.6 volts and a short circuit current of 90 mA at 80 AMl suns. An equivalent circuit model of the planar multi-junction solar cell was developed.

Advances in gallium arsenide monolithic microwave integrated-circuit technology for space communications systems

NASA Technical Reports Server (NTRS)

Bhasin, K. B.; Connolly, D. J.

1986-01-01

Future communications satellites are likely to use gallium arsenide (GaAs) monolithic microwave integrated-circuit (MMIC) technology in most, if not all, communications payload subsystems. Multiple-scanning-beam antenna systems are expected to use GaAs MMIC's to increase functional capability, to reduce volume, weight, and cost, and to greatly improve system reliability. RF and IF matrix switch technology based on GaAs MMIC's is also being developed for these reasons. MMIC technology, including gigabit-rate GaAs digital integrated circuits, offers substantial advantages in power consumption and weight over silicon technologies for high-throughput, on-board baseband processor systems. In this paper, current developments in GaAs MMIC technology are described, and the status and prospects of the technology are assessed.

24. DETAIL EXTERIOR VIEW LOOKING EAST, SHOWING FISH LADDER AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. DETAIL EXTERIOR VIEW LOOKING EAST, SHOWING FISH LADDER AT NORTH END OF DAM/SPILLWAY; WATER FLOWING THROUGH FISH LADDER IS VISIBLE AT BOTTOM. - Bonneville Project, Bonneville Dam, Columbia River, Bonneville, Multnomah County, OR

Conjugated ladder polymers by a cyclopentannulation polymerization

DOE PAGES

Bheemireddy, Sambasiva R.; Hautzinger, Matthew P.; Li, Tao; ...

2017-04-03

Here, we report a nontraditional synthesis of cyclopentafused-polycyclic aromatic hydrocarbon embedded ladder polymers using a palladium catalyzed cyclopentannulation polymerization followed by a cyclodehydrogenation reaction. Donor–acceptor type polymers containing a cyclopenta[hi]aceanthrylene acceptor groups can be synthesized by a palladium catalyzed copolymerization between 9,10-dibromoanthracene and a variety of bis(arylethynyl)arenes to give polymers with molecular weights (Mn) of 9–22 kDa. The bis(arylethynyl)arenes were composed of benzene, thiophene, or thieno[3,2- b]thiophene moieties, which provided access to a series of four donor–acceptor copolymers. The polymers were subjected to cyclodehydrogenation with FeCl 3 to access rigid ladder type polymers with the conversion investigated by 13C NMRmore » of isotopically labeled polymers. As a result, the ladder polymers possess broad UV–Vis absorptions and narrow optical band gaps of 1.17–1.29 eV and are p-type semiconductors in organic field effect transistors.« less

Conjugated ladder polymers by a cyclopentannulation polymerization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bheemireddy, Sambasiva R.; Hautzinger, Matthew P.; Li, Tao

Here, we report a nontraditional synthesis of cyclopentafused-polycyclic aromatic hydrocarbon embedded ladder polymers using a palladium catalyzed cyclopentannulation polymerization followed by a cyclodehydrogenation reaction. Donor–acceptor type polymers containing a cyclopenta[hi]aceanthrylene acceptor groups can be synthesized by a palladium catalyzed copolymerization between 9,10-dibromoanthracene and a variety of bis(arylethynyl)arenes to give polymers with molecular weights (Mn) of 9–22 kDa. The bis(arylethynyl)arenes were composed of benzene, thiophene, or thieno[3,2- b]thiophene moieties, which provided access to a series of four donor–acceptor copolymers. The polymers were subjected to cyclodehydrogenation with FeCl 3 to access rigid ladder type polymers with the conversion investigated by 13C NMRmore » of isotopically labeled polymers. As a result, the ladder polymers possess broad UV–Vis absorptions and narrow optical band gaps of 1.17–1.29 eV and are p-type semiconductors in organic field effect transistors.« less

The Ladder of Life Detection.

PubMed

Neveu, Marc; Hays, Lindsay E; Voytek, Mary A; New, Michael H; Schulte, Mitchell D

2018-06-04

We describe the history and features of the Ladder of Life Detection, a tool intended to guide the design of investigations to detect microbial life within the practical constraints of robotic space missions. To build the Ladder, we have drawn from lessons learned from previous attempts at detecting life and derived criteria for a measurement (or suite of measurements) to constitute convincing evidence for indigenous life. We summarize features of life as we know it, how specific they are to life, and how they can be measured, and sort these features in a general sense based on their likelihood of indicating life. Because indigenous life is the hypothesis of last resort in interpreting life-detection measurements, we propose a small but expandable set of decision rules determining whether the abiotic hypothesis is disproved. In light of these rules, we evaluate past and upcoming attempts at life detection. The Ladder of Life Detection is not intended to endorse specific biosignatures or instruments for life-detection measurements, and is by no means a definitive, final product. It is intended as a starting point to stimulate discussion, debate, and further research on the characteristics of life, what constitutes a biosignature, and the means to measure them. Key Words: Life detection-Life-detection instruments-Biosignatures-Biomarkers. Astrobiology 18, xxx-xxx.

Discussing Laddering Application by the Means-End Chain Theory

ERIC Educational Resources Information Center

Veludo-de-Oliveira, Tania Modesto; Ikeda, Ana Akemi; Campomar, Marcos Cortez

2006-01-01

This article aims at analyzing laddering as a technique of qualitative research, emphasizing the procedures for data collection, analysis and interpretation, and its main limitations as well. "Laddering refers to an in-depth, one-on-one interviewing technique used to develop an understanding of how consumers translate the attributes of products…

Teacher Career Ladders in Utah: Perspectives on Early Stages.

ERIC Educational Resources Information Center

Peterson, Ken, Ed.; And Others

The status of teacher career ladders in Utah is discussed from five different perspectives. Jim Wilson, representing the Legislative Research Analyst's Office and General Counsel of the Legislature, speaks about legislative intent from the past year and what legislators thought would happen and wanted to happen regarding career ladder bills which…

22. DETAIL EXTERIOR VIEW LOOKING NORTHWEST, SHOWING FISH LADDER AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

22. DETAIL EXTERIOR VIEW LOOKING NORTHWEST, SHOWING FISH LADDER AT NORTH END OF DAM/SPILLWAY; VIEW SHOWS SECTION OF FISH LADDER NEAR WHERE IT ENTERS THE COLUMBIA RIVER. - Bonneville Project, Bonneville Dam, Columbia River, Bonneville, Multnomah County, OR

Biomechanical analysis of loading/unloading a ladder on a truck.

PubMed

Moriguchi, Cristiane Shinohara; Carnaz, Leticia; de Miranda, Luiz Carlos; Marklin, Richard William; Coury, Helenice Jane Cote Gil

2012-01-01

Loading/unloading a ladder on vehicles are frequent tasks and involve overhead handling that may expose workers to risk factors of shoulder musculoskeletal disorders. The objective of the present study was to evaluate posture, forces required and perceived exertion when loading and unloading the ladder on a utility truck. Thirteen male overhead line workers from an electric utility in Brazil participated in this study. Shoulder elevation angle was measured using inclinometers. The required force to load/unload the ladder was measured by dynamometer. Subjective assessment of the perceived exertion was recorded to compare the exertion reported during the test conditions to the field conditions. The task of loading/unloading the ladder presented risks of shoulder musculoskeletal disorders (MSDs) to workers because it requires high levels of force (approximately 60% of the maximal force) combined with overhead posture of the shoulders (more than 100° from the neutral posture). Age and height presented to interfere in biomechanical risks presented in load/unload task. There was no significant difference between the subjective exertion during the test conditions and handling the ladder in the field. Ergonomic intervention is recommended to reduce these risks for shoulder MSDs.

Electronic circuits

NASA Technical Reports Server (NTRS)

1976-01-01

Twenty-nine circuits and circuit techniques developed for communications and instrumentation technology are described. Topics include pulse-code modulation, phase-locked loops, data coding, data recording, detection circuits, logic circuits, oscillators, and amplifiers.

7. DETAIL VIEW OF LOWER MOUTH OF FISH LADDER AT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. DETAIL VIEW OF LOWER MOUTH OF FISH LADDER AT ROCK OUTCROPPING, SHOWING NATURAL CARVED ROCK POOLS, UPPER PORTION OF FISH LADDER VISIBLE IN DISTANCE, LOOKING SOUTHWEST (UPSTREAM) - Van Arsdale Dam, South Fork of Eel River, Ukiah, Mendocino County, CA

Topological phases in frustrated synthetic ladders with an odd number of legs

NASA Astrophysics Data System (ADS)

Barbarino, Simone; Dalmonte, Marcello; Fazio, Rosario; Santoro, Giuseppe E.

2018-01-01

The realization of the Hofstadter model in a strongly anisotropic ladder geometry has now become possible in one-dimensional optical lattices with a synthetic dimension. In this work, we show how the Hofstadter Hamiltonian in such ladder configurations hosts a topological phase of matter which is radically different from its two-dimensional counterpart. This topological phase stems directly from the hybrid nature of the ladder geometry and is protected by a properly defined inversion symmetry. We start our analysis by considering the paradigmatic case of a three-leg ladder which supports a topological phase exhibiting the typical features of topological states in one dimension: robust fermionic edge modes, a degenerate entanglement spectrum, and a nonzero Zak phase; then, we generalize our findings—addressable in the state-of-the-art cold-atom experiments—to ladders with a higher number of legs.

Ladder operators for the Klein-Gordon equation with a scalar curvature term

NASA Astrophysics Data System (ADS)

Mück, Wolfgang

2018-01-01

Recently, Cardoso, Houri and Kimura constructed generalized ladder operators for massive Klein-Gordon scalar fields in space-times with conformal symmetry. Their construction requires a closed conformal Killing vector, which is also an eigenvector of the Ricci tensor. Here, a similar procedure is used to construct generalized ladder operators for the Klein-Gordon equation with a scalar curvature term. It is proven that a ladder operator requires the existence of a conformal Killing vector, which must satisfy an additional property. This property is necessary and sufficient for the construction of a ladder operator. For maximally symmetric space-times, the results are equivalent to those of Cardoso, Houri and Kimura.

30 CFR 57.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Fixed ladder anchorage and toe clearance. 57.11005 Section 57.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Travelways and Escapeways Travelways-Surface and Underground § 57.11005 Fixed ladder anchorage and...

30 CFR 57.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fixed ladder anchorage and toe clearance. 57.11005 Section 57.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Travelways and Escapeways Travelways-Surface and Underground § 57.11005 Fixed ladder anchorage and...

30 CFR 57.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fixed ladder anchorage and toe clearance. 57.11005 Section 57.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Travelways and Escapeways Travelways-Surface and Underground § 57.11005 Fixed ladder anchorage and...

30 CFR 57.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fixed ladder anchorage and toe clearance. 57.11005 Section 57.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Travelways and Escapeways Travelways-Surface and Underground § 57.11005 Fixed ladder anchorage and...

30 CFR 57.11005 - Fixed ladder anchorage and toe clearance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fixed ladder anchorage and toe clearance. 57.11005 Section 57.11005 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... MINES Travelways and Escapeways Travelways-Surface and Underground § 57.11005 Fixed ladder anchorage and...

Face-to-face confrontation: effects of closed-circuit technology on children's eyewitness testimony and jurors' decisions.

PubMed

Goodman, G S; Tobey, A E; Batterman-Faunce, J M; Orcutt, H; Thomas, S; Shapiro, C; Sachsenmaier, T

1998-04-01

The present study was designed to examine effects of closed-circuit technology on children's testimony and jurors' perceptions of child witnesses. For the study, a series of elaborately staged mock trials was held. First, 5- to 6-year-old and 8- to 9-year-old children individually participated in a play session with an unfamiliar male confederate. Approximately 2 weeks later, children individually testified about the event at downtown city courtroom. Mock juries composed of community recruits viewed the trials, with the child's testimony presented either live in open court or over closed-circuit television. Mock jurors made ratings concerning the child witness and the defendant, and deliberated to reach a verdict. Results indicated that overall, older children were more accurate witnesses than younger children. However, older, not younger children produced more inaccurate information in free recall. Compared to live testimony in open court, use of closed-circuit technology led to decreased suggestibility for younger children. Testifying in open court was also associated with children experiencing greater pretrial anxiety. Closed-circuit technology did not diminish fact finders' abilities to discriminate accurate from inaccurate child testimony, nor did it directly bias jurors against the defendant. However, closed-circuit testimony biased jurors against child witnesses. Moreover, jurors tended to base their impressions of witness credibility on perceived confidence and consistency. Implications for the use of closed-circuit technology when children testify are discussed.

The new technological solution for the JT-60SA quench protection circuits

NASA Astrophysics Data System (ADS)

Gaio, E.; Maistrello, A.; Novello, L.; Matsukawa, M.; Perna, M.; Ferro, A.; Yamauchi, K.; Piovan, R.

2018-07-01

An advanced technology has been developed and employed for the main circuit breakers (CB) of the quench protection circuits (QPC) of the superconducting coils of JT-60SA: it consists in a Hybrid mechanical-static CB (HCB) composed of a mechanical Bypass switch (BPS) for conducting the continuous current, in parallel to a static circuit breaker (SCB) based on integrated gate commutated thyristor (IGCT) for current interruption. It was the result of a R&D program carried out since 2006 to identify innovative solutions for the interruption of high dc current, able to improve the maintainability and availability of the CB. The HCB developed for the JT-60SA QPC is the first realization of a dc circuit breaker based on this design approach for interrupting current of some tens of kA with reapplied voltage of some kV. It also represents the first application of hybrid technology with IGCT for protection of superconducting magnets in fusion experiments. The paper aims at giving a comprehensive overview of the main R&D activities devoted to the development of this new technological approach; then, the key aspects of the design, manufacturing and testing of the QPCs for JT-60SA, successfully completed in Naka Site in summer 2015 are presented. Finally, the significance of this research is discussed and the possible future developments, in particular in view of DEMO fusion reactor, are outlined.

Majorana spin liquids, topology, and superconductivity in ladders

NASA Astrophysics Data System (ADS)

Le Hur, Karyn; Soret, Ariane; Yang, Fan

2017-11-01

We theoretically address spin chain analogs of the Kitaev quantum spin model on the honeycomb lattice. The emergent quantum spin-liquid phases or Anderson resonating valence-bond (RVB) states can be understood, as an effective model, in terms of p -wave superconductivity and Majorana fermions. We derive a generalized phase diagram for the two-leg ladder system with tunable interaction strengths between chains allowing us to vary the shape of the lattice (from square to honeycomb ribbon or brickwall ladder). We evaluate the winding number associated with possible emergent (topological) gapless modes at the edges. In the Az phase, as a result of the emergent Z2 gauge fields and π -flux ground state, one may build spin-1/2 (loop) qubit operators by analogy to the toric code. In addition, we show how the intermediate gapless B phase evolves in the generalized ladder model. For the brick-wall ladder, the B phase is reduced to one line, which is analyzed through perturbation theory in a rung tensor product states representation and bosonization. Finally, we show that doping with a few holes can result in the formation of hole pairs and leads to a mapping with the Su-Schrieffer-Heeger model in polyacetylene; a superconducting-insulating quantum phase transition for these hole pairs is accessible, as well as related topological properties.

Piezoelectric biosensor with a ladder polymer substrate coating

DOEpatents

Renschler, Clifford L.; White, Christine A.; Carter, Robert M.

1998-01-01

A piezoelectric biosensor substrate useful for immobilizing biomolecules in an oriented manner on the surface of a piezoelectric sensor has a ladder polymer of polyacrylonitrile. To make the substrate, a solution of an organic polymer, preferably polyacrylonitrile, is applied to the surface of a piezoelectric sensor. The organic polymer is modifying by heating the polymer in a controlled fashion in air such that a ladder polymer is produced which, in turn, forms the attachment point for the biomolecules comprising the piezoelectric biosensor.

Fractal ladder models and power law wave equations

PubMed Central

Kelly, James F.; McGough, Robert J.

2009-01-01

The ultrasonic attenuation coefficient in mammalian tissue is approximated by a frequency-dependent power law for frequencies less than 100 MHz. To describe this power law behavior in soft tissue, a hierarchical fractal network model is proposed. The viscoelastic and self-similar properties of tissue are captured by a constitutive equation based on a lumped parameter infinite-ladder topology involving alternating springs and dashpots. In the low-frequency limit, this ladder network yields a stress-strain constitutive equation with a time-fractional derivative. By combining this constitutive equation with linearized conservation principles and an adiabatic equation of state, a fractional partial differential equation that describes power law attenuation is derived. The resulting attenuation coefficient is a power law with exponent ranging between 1 and 2, while the phase velocity is in agreement with the Kramers–Kronig relations. The fractal ladder model is compared to published attenuation coefficient data, thus providing equivalent lumped parameters. PMID:19813816

Work-related falls from ladders--a follow-back study of US emergency department cases.

PubMed

Lombardi, David A; Smith, Gordon S; Courtney, Theodore K; Brennan, Melanye J; Kim, Jae Young; Perry, Melissa J

2011-11-01

Ladder falls comprise 16% of all US workplace fall-related fatalities, and ladder use may be particularly hazardous among older workers. This follow-back study of injured workers from a nationally representative sample of US emergency departments (ED) focused on factors related to ladder falls in three domains of the work environment: work equipment, work practices, and worker-related factors. Risk factors for fractures, the most frequent and severe outcome, were also evaluated. Workers injured from a ladder fall, treated in one of the 65 participating ED in the occupational National Electronic Injury Surveillance System (NEISS) were asked to participate. The questionnaire included worker demographics, injury, ladder and work equipment and environment characteristics, work tasks, and activities. Multivariate logistic regression models estimated odds ratios and 95% confidence intervals of a work-related fracture. Three-hundred and six workers experiencing an injury from an--on average--7.5-foot-fall from a step, extension, or straight ladder were interviewed primarily from construction, installation, maintenance, and repair professions. Injuries were most frequently to the arm, elbow or shoulder; head, neck, or face with diagnoses were primarily fracture, strain, sprain, contusion or abrasion. Workers were most frequently standing or sitting on the ladder while installing, hanging an item, or performing a repair when they fell. Ladder movement was the mechanism in 40% of falls. Environmental conditions played a role in <10% of cases. There was a significant association between fracture risk and fall height while working on the ladder that was also influenced by older work age. This study advances knowledge of falls from ladders to support those who specify means and methods, select equipment, and plan, supervise, or manage the performance of employees working at heights.

Technological Literacy Learning with Cumulative and Stepwise Integration of Equations into Electrical Circuit Diagrams

ERIC Educational Resources Information Center

Ozogul, G.; Johnson, A. M.; Moreno, R.; Reisslein, M.

2012-01-01

Technological literacy education involves the teaching of basic engineering principles and problem solving, including elementary electrical circuit analysis, to non-engineering students. Learning materials on circuit analysis typically rely on equations and schematic diagrams, which are often unfamiliar to non-engineering students. The goal of…

Effect of risk ladder format on risk perception in high- and low-numerate individuals.

PubMed

Keller, Carmen; Siegrist, Michael; Visschers, Vivianne

2009-09-01

Utilizing a random sample from the general population (N= 257), we examined the effect of the radon risk ladder on risk perception, as qualified by respondents' numeracy. The radon risk ladder provides comparative risk information about the radon equivalent of smoking risk. We compared a risk ladder providing smoking risk information with a risk ladder not providing this information. A 2 (numeracy; high, low) x 3 (risk level; high, medium, low) x 2 (smoking risk comparison: with/without) between subjects experimental design was used. A significant (p < 0.045) three-way interaction between format, risk level, and numeracy was identified. Participants with low numeracy skills, as well as participants with high numeracy skills, generally distinguished between low, medium, and high risk levels when the risk ladder with comparative smoking risk information was presented. When the risk ladder without the comparative information about the smoking risk was presented, low-numerate individuals differentiated between risk levels to a much lesser extent than high-numerate individuals did. These results provide empirical evidence that the risk ladder can be a useful tool in enabling people to interpret various risk levels. Additionally, these results allow us to conclude that providing comparative information within a risk ladder is particularly helpful to the understanding of different risk levels by people with low numeracy skills.

Piezoelectric biosensor with a ladder polymer substrate coating

DOEpatents

Renschler, C.L.; White, C.A.; Carter, R.M.

1998-09-29

A piezoelectric biosensor substrate useful for immobilizing biomolecules in an oriented manner on the surface of a piezoelectric sensor has a ladder polymer of polyacrylonitrile. To make the substrate, a solution of an organic polymer, preferably polyacrylonitrile, is applied to the surface of a piezoelectric sensor. The organic polymer is modifying by heating the polymer in a controlled fashion in air such that a ladder polymer is produced which, in turn, forms the attachment point for the biomolecules comprising the piezoelectric biosensor. 3 figs.

An innovative approach to predict technology evolution for the desoldering of printed circuit boards: A perspective from China and America.

PubMed

Wang, Chen; Zhao, Wu; Wang, Jie; Chen, Ling; Luo, Chun-Jing

2016-06-01

The printed circuit boards basis of electronic equipment have seen a rapid growth in recent years and played a significant role in modern life. Nowadays, the fact that electronic devices upgrade quickly necessitates a proper management of waste printed circuit boards. Non-destructive desoldering of waste printed circuit boards becomes the first and the most crucial step towards recycling electronic components. Owing to the diversity of materials and components, the separation process is difficult, which results in complex and expensive recovery of precious materials and electronic components from waste printed circuit boards. To cope with this problem, we proposed an innovative approach integrating Theory of Inventive Problem Solving (TRIZ) evolution theory and technology maturity mapping system to forecast the evolution trends of desoldering technology of waste printed circuit boards. This approach can be applied to analyse the technology evolution, as well as desoldering technology evolution, then research and development strategy and evolution laws can be recommended. As an example, the maturity of desoldering technology is analysed with a technology maturity mapping system model. What is more, desoldering methods in different stages are analysed and compared. According to the analysis, the technological evolution trends are predicted to be 'the law of energy conductivity' and 'increasing the degree of idealisation'. And the potential technology and evolutionary state of waste printed circuit boards are predicted, offering reference for future waste printed circuit boards recycling. © The Author(s) 2016.

Survey of key technologies on millimeter-wave CMOS integrated circuits

NASA Astrophysics Data System (ADS)

Yu, Fei; Gao, Lei; Li, Lixiang; Cai, Shuo; Wang, Wei; Wang, Chunhua

2018-05-01

In order to provide guidance for the development of high performance millimeter-wave complementary metal oxide semiconductor (MMW-CMOS) integrated circuits (IC), this paper provides a survey of key technologies on MMW-CMOS IC. Technical background of MMW wireless communications is described. Then the recent development of the critical technologies of the MMW-CMOS IC are introduced in detail and compared. A summarization is given, and the development prospects on MMW-CMOS IC are also discussed.

Teacher Attitudes toward Career Ladder.

ERIC Educational Resources Information Center

Dickson, LouAnn

An evaluation of teacher attitudes toward a public schools career ladder program is presented. Survey questionnaires mailed to 3,239 administrators, nonprogram teachers, and participating teachers elicited 1,683 returns for a 52 percent response rate. Findings indicate that the majority of teachers favored continuation of the career ladder…

Experimental ladder proof of Hardy's nonlocality for high-dimensional quantum systems

NASA Astrophysics Data System (ADS)

Chen, Lixiang; Zhang, Wuhong; Wu, Ziwen; Wang, Jikang; Fickler, Robert; Karimi, Ebrahim

2017-08-01

Recent years have witnessed a rapidly growing interest in high-dimensional quantum entanglement for fundamental studies as well as towards novel applications. Therefore, the ability to verify entanglement between physical qudits, d -dimensional quantum systems, is of crucial importance. To show nonclassicality, Hardy's paradox represents "the best version of Bell's theorem" without using inequalities. However, so far it has only been tested experimentally for bidimensional vector spaces. Here, we formulate a theoretical framework to demonstrate the ladder proof of Hardy's paradox for arbitrary high-dimensional systems. Furthermore, we experimentally demonstrate the ladder proof by taking advantage of the orbital angular momentum of high-dimensionally entangled photon pairs. We perform the ladder proof of Hardy's paradox for dimensions 3 and 4, both with the ladder up to the third step. Our paper paves the way towards a deeper understanding of the nature of high-dimensionally entangled quantum states and may find applications in quantum information science.

Corrosion Control Specialist Career Ladder AFSC 53530, 53550, 53570, and 53690. Occupational Survey Report.

ERIC Educational Resources Information Center

Air Force Occupational Measurement Center, Lackland AFB, TX.

The report describes the results of a detailed occupational survey of the corrosion control career ladder. Responses to a 457-task, time rating inventory from 1,015 personnel (representing 64 percent of the career field) were analyzed to produce seven specific findings and the career ladder structure. The career ladder includes a variety of jobs…

Ladder physics in the spin fermion model

NASA Astrophysics Data System (ADS)

Tsvelik, A. M.

2017-05-01

A link is established between the spin fermion (SF) model of the cuprates and the approach based on the analogy between the physics of doped Mott insulators in two dimensions and the physics of fermionic ladders. This enables one to use nonperturbative results derived for fermionic ladders to move beyond the large-N approximation in the SF model. It is shown that the paramagnon exchange postulated in the SF model has exactly the right form to facilitate the emergence of the fully gapped d -Mott state in the region of the Brillouin zone at the hot spots of the Fermi surface. Hence, the SF model provides an adequate description of the pseudogap.

Ladder physics in the spin fermion model

DOE PAGES

Tsvelik, A. M.

2017-05-01

A link is established between the spin fermion (SF) model of the cuprates and the approach based on the analogy between the physics of doped Mott insulators in two dimensions and the physics of fermionic ladders. This enables one to use nonperturbative results derived for fermionic ladders to move beyond the large-N approximation in the SF model. Here, it is shown that the paramagnon exchange postulated in the SF model has exactly the right form to facilitate the emergence of the fully gapped d-Mott state in the region of the Brillouin zone at the hot spots of the Fermi surface.more » Hence, the SF model provides an adequate description of the pseudogap.« less

Evaluation through research of a three-track career ladder program for registered nurses.

PubMed

Korman, Carol; Eliades, Aris Beoglos

2010-01-01

A descriptive study design was employed to survey registered nurse participants in a career ladder program comprising of three tracks: clinical, education, and management. Findings indicate that participation allows nurses of varying education preparation and roles to demonstrate professional development. Implications for staff development include efficacy of the online survey technique, provision of a reliable tool to evaluate a career ladder, and evaluation of a career ladder that includes the staff development educator.

29 CFR 1926.1053 - Ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... ascend or descend without continually having to hold, push or pull any part of the device, leaving both... the carrier. When the system is exposed to wind, cable guides for flexible carriers shall be installed... mountings and cable guides shall not reduce the design strength of the ladder. (24) The side rails of...

29 CFR 1926.1053 - Ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... ascend or descend without continually having to hold, push or pull any part of the device, leaving both... the carrier. When the system is exposed to wind, cable guides for flexible carriers shall be installed... mountings and cable guides shall not reduce the design strength of the ladder. (24) The side rails of...

Dissipation, Voltage Profile and Levy Dragon in a Special Ladder Network

ERIC Educational Resources Information Center

Ucak, C.

2009-01-01

A ladder network constructed by an elementary two-terminal network consisting of a parallel resistor-inductor block in series with a parallel resistor-capacitor block sometimes is said to have a non-dispersive dissipative response. This special ladder network is created iteratively by replacing the elementary two-terminal network in place of the…

The technology on noise reduction of the APD detection circuit

NASA Astrophysics Data System (ADS)

Wu, Xue-ying; Zheng, Yong-chao; Cui, Jian-yong

2013-09-01

The laser pulse detection is widely used in the field of laser range finders, laser communications, laser radar, laser Identification Friend or Foe, et al, for the laser pulse detection has the advantage of high accuracy, high sensitivity and strong anti-interference. The avalanche photodiodes (APD) has the advantage of high quantum efficiency, high response speed and huge gain. The APD is particularly suitable for weak signal detection. The technology that APD acts as the photodetector for weak signal reception and amplification is widely used in laser pulse detection. The APD will convert the laser signal to weak electrical signal. The weak signal is amplified, processed and exported by the circuit. In the circuit design, the optimal signal detection is one key point in photoelectric detection system. The issue discusses how to reduce the noise of the photoelectric signal detection circuit and how to improve the signal-to-noise ratio, related analysis and practice included. The essay analyzes the mathematical model of the signal-to-noise ratio for photoelectric conversion and the noise of the APD photoelectric detection system. By analysis the bandwidth of the detection system is determined, and the circuit devices are selected that match the APD. In the circuit design separated devices with low noise are combined with integrated operational amplifier for the purpose of noise reduction. The methods can effectively suppress the noise, and improve the detection sensitivity.

Controlled parity switch of persistent currents in quantum ladders

NASA Astrophysics Data System (ADS)

Filippone, Michele; Bardyn, Charles-Edouard; Giamarchi, Thierry

2018-05-01

We investigate the behavior of persistent currents for a fixed number of noninteracting fermions in a periodic quantum ladder threaded by Aharonov-Bohm and transverse magnetic fluxes Φ and χ . We show that the coupling between ladder legs provides a way to effectively change the ground-state fermion-number parity, by varying χ . Specifically, we demonstrate that varying χ by 2 π (one flux quantum) leads to an apparent fermion-number parity switch. We find that persistent currents exhibit a robust 4 π periodicity as a function of χ , despite the fact that χ →χ +2 π leads to modifications of order 1 /N of the energy spectrum, where N is the number of sites in each ladder leg. We show that these parity-switch and 4 π periodicity effects are robust with respect to temperature and disorder, and outline potential physical realizations using cold atomic gases and photonic lattices, for bosonic analogs of the effects.

Electrical burn injuries of workers using portable aluminium ladders near overhead power lines.

PubMed

Moghtader, J C; Himel, H N; Demun, E M; Bellian, K T; Edlich, R F

1993-10-01

The use of aluminium ladders around high voltage power lines has resulted in a significant number of electrical injuries and electrocutions. Workers often misjudge wire distances or lose control of fully extended ladders, thereby exposing themselves to electrocution hazard. High-voltage electrical burns of two workers using an aluminium ladder that contacted a high voltage power line are reported. The circumstances surrounding the injury, the clinical management of the case, and the methods of prevention are presented and discussed.

29 CFR 1915.72 - Ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... shipbreaking. (a) General requirements. (1) The use of ladders with broken or missing rungs or steps, broken or... 10d common wire nails or fastened with through bolts or other fasteners of equivalent strength. Cleats... nailed to each rail with five 10d common wire nails or fastened with through bolts or other fasteners of...

Monolithic microwave integrated circuit technology for advanced space communication

NASA Technical Reports Server (NTRS)

Ponchak, George E.; Romanofsky, Robert R.

1988-01-01

Future Space Communications subsystems will utilize GaAs Monolithic Microwave Integrated Circuits (MMIC's) to reduce volume, weight, and cost and to enhance system reliability. Recent advances in GaAs MMIC technology have led to high-performance devices which show promise for insertion into these next generation systems. The status and development of a number of these devices operating from Ku through Ka band will be discussed along with anticipated potential applications.

29 CFR 1915.72 - Ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... sectional area of the side rail. The dimensions of side rails for their total length shall be those...). (b) Construction of portable wood cleated ladders up to 30 feet in length. (1) Wood side rails shall... than one such pocket appears in each 4 feet of length. (5) The width between side rails at the base...

29 CFR 1910.25 - Portable wood ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... library ladders are not specifically covered by this section. (b) Materials—(1) Requirements applicable to... device of sufficient size and strength to securely hold the front and back sections in open positions...

29 CFR 1910.25 - Portable wood ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... library ladders are not specifically covered by this section. (b) Materials—(1) Requirements applicable to... device of sufficient size and strength to securely hold the front and back sections in open positions...

29 CFR 1910.29 - Manually propelled mobile ladder stands and scaffolds (towers).

Code of Federal Regulations, 2014 CFR

2014-07-01

.... (stress grade) construction grade lumber or equivalent. (vi) All scaffold work levels 10 feet or higher... (towers). 1910.29 Section 1910.29 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND..., construction, and use of mobile work platforms (including ladder stands but not including aerial ladders) and...

29 CFR 1910.29 - Manually propelled mobile ladder stands and scaffolds (towers).

Code of Federal Regulations, 2010 CFR

2010-07-01

.... (stress grade) construction grade lumber or equivalent. (vi) All scaffold work levels 10 feet or higher... (towers). 1910.29 Section 1910.29 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND..., construction, and use of mobile work platforms (including ladder stands but not including aerial ladders) and...

29 CFR 1910.29 - Manually propelled mobile ladder stands and scaffolds (towers).

Code of Federal Regulations, 2012 CFR

2012-07-01

.... (stress grade) construction grade lumber or equivalent. (vi) All scaffold work levels 10 feet or higher... (towers). 1910.29 Section 1910.29 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND..., construction, and use of mobile work platforms (including ladder stands but not including aerial ladders) and...

29 CFR 1910.29 - Manually propelled mobile ladder stands and scaffolds (towers).

Code of Federal Regulations, 2013 CFR

2013-07-01

.... (stress grade) construction grade lumber or equivalent. (vi) All scaffold work levels 10 feet or higher... (towers). 1910.29 Section 1910.29 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND..., construction, and use of mobile work platforms (including ladder stands but not including aerial ladders) and...

29 CFR 1910.29 - Manually propelled mobile ladder stands and scaffolds (towers).

Code of Federal Regulations, 2011 CFR

2011-07-01

.... (stress grade) construction grade lumber or equivalent. (vi) All scaffold work levels 10 feet or higher... (towers). 1910.29 Section 1910.29 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND..., construction, and use of mobile work platforms (including ladder stands but not including aerial ladders) and...

29 CFR 1910.26 - Portable metal ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of ladder equipment must be employed by the users. The following rules and regulations are essential... to oil and grease, equipment should be cleaned of oil, grease, or slippery materials. This can easily...

29 CFR 1910.26 - Portable metal ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of ladder equipment must be employed by the users. The following rules and regulations are essential... to oil and grease, equipment should be cleaned of oil, grease, or slippery materials. This can easily...

29 CFR 1910.26 - Portable metal ladders.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of ladder equipment must be employed by the users. The following rules and regulations are essential... to oil and grease, equipment should be cleaned of oil, grease, or slippery materials. This can easily...

29 CFR 1917.118 - Fixed ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... bolts or structural members of tanks and towers; (3) Ladders built into or vertically attached to..., microwave communications, electrical power and similar towers, poles and structures, including stacks and... consisting of individual rungs that are attached to walls, conical manhole sections or river cells shall: (1...

29 CFR 1917.118 - Fixed ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... bolts or structural members of tanks and towers; (3) Ladders built into or vertically attached to..., microwave communications, electrical power and similar towers, poles and structures, including stacks and... consisting of individual rungs that are attached to walls, conical manhole sections or river cells shall: (1...

ABC of ladder operators for rationally extended quantum harmonic oscillator systems

NASA Astrophysics Data System (ADS)

Cariñena, José F.; Plyushchay, Mikhail S.

2017-07-01

The problem of construction of ladder operators for rationally extended quantum harmonic oscillator (REQHO) systems of a general form is investigated in the light of existence of different schemes of the Darboux-Crum-Krein-Adler transformations by which such systems can be generated from the quantum harmonic oscillator. Any REQHO system is characterized by the number of separated states in its spectrum, the number of ‘valence bands’ in which the separated states are organized, and by the total number of the missing energy levels and their position. All these peculiarities of a REQHO system are shown to be detected and reflected by a trinity (A^+/- , B^+/- , C^+/-) of the basic (primary) lowering and raising ladder operators related between themselves by certain algebraic identities with coefficients polynomially-dependent on the Hamiltonian. We show that all the secondary, higher-order ladder operators are obtainable by a composition of the basic ladder operators of the trinity which form the set of the spectrum-generating operators. Each trinity, in turn, can be constructed from the intertwining operators of the two complementary minimal schemes of the Darboux-Crum-Krein-Adler transformations.

The modelling of carbon-based supercapacitors: Distributions of time constants and Pascal Equivalent Circuits

NASA Astrophysics Data System (ADS)

Fletcher, Stephen; Kirkpatrick, Iain; Dring, Roderick; Puttock, Robert; Thring, Rob; Howroyd, Simon

2017-03-01

Supercapacitors are an emerging technology with applications in pulse power, motive power, and energy storage. However, their carbon electrodes show a variety of non-ideal behaviours that have so far eluded explanation. These include Voltage Decay after charging, Voltage Rebound after discharging, and Dispersed Kinetics at long times. In the present work, we establish that a vertical ladder network of RC components can reproduce all these puzzling phenomena. Both software and hardware realizations of the network are described. In general, porous carbon electrodes contain random distributions of resistance R and capacitance C, with a wider spread of log R values than log C values. To understand what this implies, a simplified model is developed in which log R is treated as a Gaussian random variable while log C is treated as a constant. From this model, a new family of equivalent circuits is developed in which the continuous distribution of log R values is replaced by a discrete set of log R values drawn from a geometric series. We call these Pascal Equivalent Circuits. Their behaviour is shown to resemble closely that of real supercapacitors. The results confirm that distributions of RC time constants dominate the behaviour of real supercapacitors.

29 CFR 1910.27 - Fixed ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) All rungs shall have a minimum diameter of three-fourths inch for metal ladders, except as covered in... appurtenances shall be painted or otherwise treated to resist corrosion and rusting when location demands... areas under floors, are frequently located in an atmosphere that causes corrosion and rusting. To...

Use of portable ladders - field observations and self-reported safety performance in the cable TV industry.

PubMed

Chang, Wen-Ruey; Huang, Yueng-Hsiang; Brunette, Christopher; Lee, Jin

2017-11-01

Portable ladders incidents remain a major cause of falls from heights. This study reported field observations of environments, work conditions and safety behaviour involving portable ladders and their correlations with self-reported safety performance. Seventy-five professional installers of a company in the cable and other pay TV industry were observed for 320 ladder usages at their worksites. The participants also filled out a questionnaire to measure self-reported safety performance. Proper setup on slippery surfaces, correct method for ladder inclination setup and ladder secured at the bottom had the lowest compliance with best practices and training guidelines. The observation compliance score was found to have significant correlation with straight ladder inclined angle (Pearson's r = 0.23, p < 0.0002) and employees' self-reported safety participation (r = 0.29, p < 0.01). The results provide a broad perspective on employees' safety compliance and identify areas for improving safety behaviours. Practitioner Summary: A checklist was used while observing professional installers of a cable company for portable ladder usage at their worksites. Items that had the lowest compliance with best practices and training guidelines were identified. The results provide a broad perspective on employees' safety compliance and identify areas for improving safety behaviours.

Electromagnetically induced transparency and Autler-Townes splitting in superconducting flux quantum circuits

NASA Astrophysics Data System (ADS)

Sun, Hui-Chen; Liu, Yu-xi; Ian, Hou; You, J. Q.; Il'ichev, E.; Nori, Franco

2014-06-01

We study the microwave absorption of a driven three-level quantum system, which is realized by a superconducting flux quantum circuit (SFQC), with a magnetic driving field applied to the two upper levels. The interaction between the three-level system and its environment is studied within the Born-Markov approximation, and we take into account the effects of the driving field on the damping rates of the three-level system. We study the linear response of the driven three-level SFQC to a weak probe field. The linear magnetic susceptibility of the SFQC can be changed by both the driving field and the bias magnetic flux. When the bias magnetic flux is at the optimal point, the transition from the ground state to the second-excited state is forbidden and the three-level SFQC has a ladder-type transition. Thus, the SFQC responds to the probe field like natural atoms with ladder-type transitions. However, when the bias magnetic flux deviates from the optimal point, the three-level SFQC has a cyclic transition, thus it responds to the probe field like a combination of natural atoms with ladder-type transitions and natural atoms with Λ-type transitions. In particular, we provide detailed discussions on the conditions for realizing electromagnetically induced transparency and Autler-Townes splitting in three-level SFQCs.

Orbital currents in a generalized Hubbard ladder

NASA Astrophysics Data System (ADS)

Fjaerestad, John O.

2004-03-01

We study a phase with orbital currents (d-density wave (DDW)/staggered flux phase) in a generalized Hubbard model on the two-leg ladder at zero temperature. Bosonization and perturbative renormalization-group calculations are used to identify a parameter region with long-range DDW order in the weakly interacting half-filled ladder. Finite-size density-matrix renormalization-group (DMRG) studies of ladders with up to 200 rungs, for rational hole dopings δ and intermediate-strength interactions, find that currents remain large in the doped DDW phase, with no evidence of decay.^1,2,3 Motivated by these results, we consider an effective bosonization description of the doped DDW phase in which quantum fluctuations in the total charge mode are neglected.^3 This leads to an analytically solvable Frenkel-Kontorova-like model which predicts that the staggered rung current and the rung electron density show periodic spatial oscillations with wavelengths 2/δ and 1/δ, respectively, with the density minima located at the zeros (domain walls) of the staggered rung current, in good agreement with the DMRG results. We comment on the question of the nature of the asymptotic current correlations in the doped DDW phase. ^1U. Schollwöck, S. Chakravarty, J. O. Fjaerestad, J. B. Marston, and M. Troyer, Phys. Rev. Lett. 90, 186401 (2003). ^2M. Troyer, invited talk at this meeting. ^3J. O. Fjaerestad, J. B. Marston, and U. Schollwöck, unpublished.

Staggered Orbital Currents in the Half-Filled Two-Leg Ladder

NASA Astrophysics Data System (ADS)

Fjaerestad, J. O.; Marston, Brad; Sudbo, A.

2002-03-01

We present strong analytical and numerical evidence for the existence of a staggered flux (SF) phase in the half-filled two-leg ladder, with true long-range order in the counter-circulating currents. Using abelian bosonization with a careful treatment of the Klein factors, we show that a certain phase of the half-filled ladder, previously identified as having spin-Peierls order, instead exhibits staggered orbital currents with no dimerization.(J. O. Fjærestad and J. B. Marston, cond- mat/0107094.) This result, combined with a weak-coupling renormalization-group analysis, implies that the SF phase exists in a region of the phase diagram of the half-filled t-U-V-J ladder. Using the density-matrix renormalization-group (DMRG) approach generalized to complex-valued wavefunctions, we demonstrate that the SF phase exhibits robust currents at intermediate values of the interaction strengths.

Cavity-induced artificial gauge field in a Bose-Hubbard ladder

NASA Astrophysics Data System (ADS)

Halati, Catalin-Mihai; Sheikhan, Ameneh; Kollath, Corinna

2017-12-01

We consider theoretically ultracold interacting bosonic atoms confined to quasi-one-dimensional ladder structures formed by optical lattices and coupled to the field of an optical cavity. The atoms can collect a spatial phase imprint during a cavity-assisted tunneling along a rung via Raman transitions employing a cavity mode and a transverse running wave pump beam. By adiabatic elimination of the cavity field we obtain an effective Hamiltonian for the bosonic atoms, with a self-consistency condition. Using the numerical density-matrix renormalization-group method, we obtain a rich steady-state diagram of self-organized steady states. Transitions between superfluid to Mott-insulating states occur, on top of which we can have Meissner, vortex liquid, and vortex lattice phases. Also a state that explicitly breaks the symmetry between the two legs of the ladder, namely, the biased-ladder phase, is dynamically stabilized. We investigate the influence that a trapping potential has on the stability of the self-organized phases.

Climbing the Cosmic Distance Ladder Artist Concept

NASA Image and Video Library

2012-10-03

Astronomers using NASA Spitzer Space Telescope have greatly improved the cosmic distance ladder used to measure the expansion rate of the universe, its size and age. This artist concept symbolically shows a series of stars that have known distances.

High power broadband millimeter wave TWTs

NASA Astrophysics Data System (ADS)

James, Bill G.

1999-05-01

In the early 1980's the requirement for high power broadband millimeter wave sources encouraged the development of microwave vacuum device amplifiers for radar and communication systems. Many government funded programs were implemented for the development of high power broadband millimeter wave amplifiers that would meet the needs of the high power community. The tube design capable of meeting these goals was the slow wave coupled cavity traveling wave device, which had a proven technology base at the lower frequencies (X Band). However scaling this technology to the millimeter frequencies had severe shortcomings in both thermal and manufacturing design. These shortcomings were overcome with the development of the Ladder Circuit technology. In conjunction with the circuit development high power electron beam systems had to be developed for the generation of high rf powers. These beam systems had to be capable of many megawatts of beam power density and high current densities. The cathode technology required to be capable of operating at current densities of 10 amperes per square centimeter at long pulse lengths and high duty cycle. Since the introduction of the Ladder Circuit technology a number of high power broadband millimeter wave amplifiers have been developed using this technology, and have been deployed in operating radar and communication systems. Broadband millimeter wave sources have been manufactured in the frequency range from 27 GHz to 100 GHz with power levels ranging from 100 watts to 50 kilowatts. Today the power levels achieved by these devices are nearing the limits of this technology; therefore to gain a significant increase in power at the millimeter wave frequencies other technologies will have to be considered particularly fast wave devices. This paper will briefly review the ladder circuit technology and present the designs of a number of broadband high power devices developed at Ka and W band. The discussion will include the beam systems

Estimating ladder fuels: a new approach combining field photography with LiDAR

Treesearch

Heather Kramer; Brandon Collins; Frank Lake; Marek Jakubowski; Scott Stephens; Maggi Kelly

2016-01-01

Forests historically associated with frequent fire have changed dramatically due to fire suppression and past harvesting over the last century. The buildup of ladder fuels, which carry fire from the surface of the forest floor to tree crowns, is one of the critical changes, and it has contributed to uncharacteristically large and severe fires. The abundance of ladder...

Analysis of Utah Career Ladder Plans.

ERIC Educational Resources Information Center

Murphy, Michael J.; And Others

This report analyzes the content and development of the 45 school district career ladder plans submitted in 1984 to the Utah State Office of Education. Descriptive commentary and data tables are used to examine (1) the structure and composition of planning committees; (2) teacher evaluation provisions, including changes in evaluation methods, the…

Strength Analysis on Ship Ladder Using Finite Element Method

NASA Astrophysics Data System (ADS)

Budianto; Wahyudi, M. T.; Dinata, U.; Ruddianto; Eko P., M. M.

2018-01-01

In designing the ship’s structure, it should refer to the rules in accordance with applicable classification standards. In this case, designing Ladder (Staircase) on a Ferry Ship which is set up, it must be reviewed based on the loads during ship operations, either during sailing or at port operations. The classification rules in ship design refer to the calculation of the structure components described in Classification calculation method and can be analysed using the Finite Element Method. Classification Regulations used in the design of Ferry Ships used BKI (Bureau of Classification Indonesia). So the rules for the provision of material composition in the mechanical properties of the material should refer to the classification of the used vessel. The analysis in this structure used program structure packages based on Finite Element Method. By using structural analysis on Ladder (Ladder), it obtained strength and simulation structure that can withstand load 140 kg both in static condition, dynamic, and impact. Therefore, the result of the analysis included values of safety factors in the ship is to keep the structure safe but the strength of the structure is not excessive.

A Flipped First-Year Digital Circuits Course for Engineering and Technology Students

ERIC Educational Resources Information Center

Yelamarthi, Kumar; Drake, Eron

2015-01-01

This paper describes a flipped and improved first-year digital circuits (DC) course that incorporates several active learning strategies. With the primary objective of increasing student interest and learning, an integrated instructional design framework is proposed to provide first-year engineering and technology students with practical knowledge…

Using career ladders to motivate and retain employees: an implementation success story.

PubMed

Garletts, Joseph A

2002-01-01

In October 2000, Phoenix-based Sonora Quest Laboratories, LLC (SQL), commissioned The Gelfond Group to survey SQL employees. Responding to negative survey scores, SQL developed and implemented an entry-level career ladder for line staff of the specimen management/referral testing department. The program was piloted in February 2001, and was implemented fully shortly thereafter. The ladder was designed to provide job enrichment opportunities through company-conducted training and advancement provisions. It contained requirements for productivity and quality of work performed in addition to increasingly rigorous training and competency documentation. Employees were accountable for their own advancement and for ensuring that all documentation was complete. Advancement was automatic once requirements were completed. Pay increases accompanied each advancement on a predetermined scale. At the end of 12 months, employee turnover dropped from 39% to less than 20% annually. Both productivity and morale improved, and results on a second employee survey indicated dramatic improvement in five key areas. The career ladder concept has been replicated successfully in several other departments, including phlebotomy, and a six-tiered ladder is under development for the clinical laboratory. It will encompass CLA, MLT, and MT positions from entry level to technical coordinator.

Synthesis of dibenzothiophene-containing ladder polysilsesquioxane as a blue phosphorescent host material.

PubMed

Ren, Zhongjie; Sun, Dianming; Li, Huihui; Fu, Qiang; Ma, Dongge; Zhang, Jianming; Yan, Shouke

2012-03-26

A ladder polysilsesquioxanes with side chain of dibenzothiophene groups (BS-LPSQ) was successfully synthesized. The ladder structure of BS-LPSQ was characterized by MALDI-TOF MS, XRD, and (1)H NMR spectroscopy. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), atomic force microscopy (AFM), and spectroscopic analyses revealed that the BS-LPSQ has good film-forming ability, high thermal and morphological stability, and good miscibility to the dopant iridium bis(4,6-difluorophenyl)pyridinato-N,C(2)-picolinate (FIrpic), high triplet energy, and a wide bandgap. In addition, compared with the ringed polysiloxane BS-PSQ phosphorescent host material reported previously, the ladder structure of BS-LPSQ has not only a higher thermal resistance, but also could prevent molecular aggregation and effectively avoid quenching of fluorescence. Thus, the BS-LPSQ may be used as a better host for the blue-light-emitting iridium complex FIrpic. The performance of the electrophosphorescent device, based on the ladder BS-LPSQ as the active layer, is superior to that of ringed BS-PSQ and any other polyhedral oligomeric silsesquioxane (POSS)-based or polymer host materials. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Investigation of noise insensitive electronic circuits for automotive applications with particular regard to MOS circuits

NASA Astrophysics Data System (ADS)

Gorille, I.

1980-11-01

The application of MOS switching circuits of high complexity in essential automobile systems, such as ignition and injection, was investigated. A bipolar circuit technology, current hogging logic (CHL), was compared to MOS technologies for its competitiveness. The functional requirements of digital automotive systems can only be met by technologies allowing large packing densities and medium speeds. The properties of n-MOS and CMOS are promising whereas the electrical power needed by p-MOS circuits is in general prohibitively large.

Process technology and effects of spallation products: Circuit components, maintenance, and handling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigg, B.; Haines, S.J.; Dressler, R.

1996-06-01

Working Session D included an assessment of the status of the technology and components required to: (1) remove impurities from the liquid metal (mercury or Pb-Bi) target flow loop including the effects of spallation products, (2) provide the flow parameters necessary for target operations, and (3) maintain the target system. A series of brief presentations were made to focus the discussion on these issues. The subjects of these presentations, and presenters were: (1) Spallation products and solubilities - R. Dressler; (2) Spallation products for Pb-Bi - Y. Orlov; (3) Clean/up/impurity removal components - B. Sigg; (4) {open_quotes}Road-Map{close_quotes} and remote handlingmore » needs - T. McManamy; (5) Remote handling issues and development - M. Holding. The overall conclusion of this session was that, with the exception of (i) spallation product related processing issues, (ii) helium injection and clean-up, and (iii) specialized remote handling equipment, the technology for all other circuit components (excluding the target itself) exists. Operating systems at the Institute of Physics in Riga, Latvia (O. Lielausis) and at Ben-Gurion University in Beer Shiva, Israel (S. Lesin) have demonstrated that other liquid metal circuit components including pumps, heat exchangers, valves, seals, and piping are readily available and have been reliably used for many years. In the three areas listed above, the designs and analysis are not judged to be mature enough to determine whether and what types of technology development are required. Further design and analysis of the liquid metal target system is therefore needed to define flow circuit processing and remote handling equipment requirements and thereby identify any development needs.« less

Digital MOS integrated circuits

NASA Astrophysics Data System (ADS)

Elmasry, M. I.

MOS in digital circuit design is considered along with aspects of digital VLSI, taking into account a comparison of MOSFET logic circuits, 1-micrometer MOSFET VLSI technology, a generalized guide for MOSFET miniaturization, processing technologies, novel circuit structures for VLSI, and questions of circuit and system design for VLSI. MOS memory cells and circuits are discussed, giving attention to a survey of high-density dynamic RAM cell concepts, one-device cells for dynamic random-access memories, variable resistance polysilicon for high density CMOS Ram, high performance MOS EPROMs using a stacked-gate cell, and the optimization of the latching pulse for dynamic flip-flop sensors. Programmable logic arrays are considered along with digital signal processors, microprocessors, static RAMs, and dynamic RAMs.

29 CFR 1910.26 - Portable metal ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Walking-Working Surfaces § 1910.26 Portable metal ladders. (a... material for the safety of the user. (viii) A metal spreader or locking device of sufficient size and...

Chutes and Ladders for the Impatient

ERIC Educational Resources Information Center

Cheteyan, Leslie A.; Hengeveld, Stewart; Jones, Michael A.

2011-01-01

In this paper, we review the rules and game board for "Chutes and Ladders", define a Markov chain to model the game regardless of the spinner range, and describe how properties of Markov chains are used to determine that an optimal spinner range of 15 minimizes the expected number of turns for a player to complete the game. Because the Markov…

34. Attic, from folding ladder, looking north Veterans Administration ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. Attic, from folding ladder, looking north - Veterans Administration Center, Officers Duplex Quarters, 5302 East Kellogg (Legal Address); 5500 East Kellogg (Common Address), Wichita, Sedgwick County, KS

Educational-research laboratory "electric circuits" on the base of digital technologies

NASA Astrophysics Data System (ADS)

Koroteyev, V. I.; Florentsev, V. V.; Florentseva, N. I.

2017-01-01

The problem of research activity of trainees' activation in the educational-research laboratory "Electric Circuits" using innovative methodological solutions and digital technologies is considered. The main task is in creation of the unified experimental research information-educational environment "Electrical Engineering". The problems arising during the developing and application of the modern software and hardware, experimental and research stands and digital control and measuring systems are presented. This paper presents the main stages of development and creation of educational-research laboratory "Electrical Circuits" at the Department of Electrical Engineering of NRNU MEPhI. The authors also consider the analogues of the described research complex offered by various educational institutions and companies. The analysis of their strengths and weaknesses, on which the advantages of the proposed solution are based, is held.

Ladders and Easels and Stools, Oh My!

ERIC Educational Resources Information Center

Greenman, Geri

2002-01-01

Describes an art lesson for high school seniors in an intermediate oil painting class. Explains that the teacher set up a still life with a ladder, easel, and a stool with a white background to capture the shadows. States that the students painted their still life in oil. (CMK)

Multi-Layer E-Textile Circuits

NASA Technical Reports Server (NTRS)

Dunne, Lucy E.; Bibeau, Kaila; Mulligan, Lucie; Frith, Ashton; Simon, Cory

2012-01-01

Stitched e-textile circuits facilitate wearable, flexible, comfortable wearable technology. However, while stitched methods of e-textile circuits are common, multi-layer circuit creation remains a challenge. Here, we present methods of stitched multi-layer circuit creation using accessible tools and techniques.

Building New Career Ladders in Clerical Occupations: Final Report for the Period July 1, 1974-June 30, 1975.

ERIC Educational Resources Information Center

National Council of Negro Women, New York, NY.

A project by the National Council of Negro Women called "Building New Career Ladders in Clerical Occupations" has five components. Two of these are: (1) development of career ladders on the job; and (2) testing, evaluation, and dissemination. In the career ladder component, 33 companies participated through financial contributions; giving…

Adaptation of a ladder beam walking task to assess locomotor recovery in mice following spinal cord injury.

PubMed

Cummings, Brian J; Engesser-Cesar, Christie; Cadena, Gilbert; Anderson, Aileen J

2007-02-27

Locomotor impairments after spinal cord injury (SCI) are often assessed using open-field rating scales. These tasks have the advantage of spanning the range from complete paralysis to normal walking; however, they lack sensitivity at specific levels of recovery. Additionally, most supplemental assessments were developed in rats, not mice. For example, the horizontal ladder beam has been used to measure recovery in the rat after SCI. This parametric task results in a videotaped archival record of the event, is easily administered, and is unambiguously scored. Although a ladder beam apparatus for mice is available, its use in the assessment of recovery in SCI mice is rare, possibly because normative data for uninjured mice and the type of step misplacements injured mice exhibit is lacking. We report the development of a modified ladder beam instrument and scoring system to measure hindlimb recovery in vertebral T9 contusion spinal cord injured mice. The mouse ladder beam allows for the use of standard parametric statistical tests to assess locomotor recovery. Ladder beam performance is consistent across four strains of mice, there are no sex differences, and inter-rater reliability between observers is high. The ladder beam score is proportional to injury severity and can be used to easily separate mice capable of weight-supported stance up to mice with consistent forelimb to hindlimb coordination. Critically, horizontal ladder beam testing discriminates between mice that score identically in terms of stepping frequency in open-field testing.

Adaptation of a ladder beam walking task to assess locomotor recovery in mice following spinal cord injury

PubMed Central

Cummings, Brian J.; Engesser-Cesar, Christie; Anderson, Aileen J.

2007-01-01

Locomotor impairments after spinal cord injury (SCI) are often assessed using open-field rating scales. These tasks have the advantage of spanning the range from complete paralysis to normal walking; however, they lack sensitivity at specific levels of recovery. Additionally, most supplemental assessments were developed in rats, not mice. For example, the horizontal ladder beam has been used to measure recovery in the rat after SCI. This parametric task results in a videotaped archival record of the event, is easily administered, and is unambiguously scored. Although a ladder beam apparatus for mice is available, its use in the assessment of recovery in SCI mice is rare, possibly because normative data for uninjured mice and the type of step misplacements injured mice exhibit is lacking. We report the development of a modified ladder beam instrument and scoring system to measure hindlimb recovery in vertebral T9 contusion spinal cord injured mice. The mouse ladder beam allows for the use of standard parametric statistical tests to assess locomotor recovery. Ladder beam performance is consistent across four strains of mice, there are no sex differences, and inter-rater reliability between observers is high. The ladder beam score is proportional to injury severity and can be used to easily separate mice capable of weight-supported stance up to mice with consistent forelimb to hindlimb coordination. Critically, horizontal ladder beam testing discriminates between mice that score identically in terms of stepping frequency in open-field testing. PMID:17197044

Development Of A Three-Dimensional Circuit Integration Technology And Computer Architecture

NASA Astrophysics Data System (ADS)

Etchells, R. D.; Grinberg, J.; Nudd, G. R.

1981-12-01

This paper is the first of a series 1,2,3 describing a range of efforts at Hughes Research Laboratories, which are collectively referred to as "Three-Dimensional Microelectronics." The technology being developed is a combination of a unique circuit fabrication/packaging technology and a novel processing architecture. The packaging technology greatly reduces the parasitic impedances associated with signal-routing in complex VLSI structures, while simultaneously allowing circuit densities orders of magnitude higher than the current state-of-the-art. When combined with the 3-D processor architecture, the resulting machine exhibits a one- to two-order of magnitude simultaneous improvement over current state-of-the-art machines in the three areas of processing speed, power consumption, and physical volume. The 3-D architecture is essentially that commonly referred to as a "cellular array", with the ultimate implementation having as many as 512 x 512 processors working in parallel. The three-dimensional nature of the assembled machine arises from the fact that the chips containing the active circuitry of the processor are stacked on top of each other. In this structure, electrical signals are passed vertically through the chips via thermomigrated aluminum feedthroughs. Signals are passed between adjacent chips by micro-interconnects. This discussion presents a broad view of the total effort, as well as a more detailed treatment of the fabrication and packaging technologies themselves. The results of performance simulations of the completed 3-D processor executing a variety of algorithms are also presented. Of particular pertinence to the interests of the focal-plane array community is the simulation of the UNICORNS nonuniformity correction algorithms as executed by the 3-D architecture.

49 CFR 214.519 - Floors, decks, stairs, and ladders of on-track roadway maintenance machines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... roadway maintenance machines. 214.519 Section 214.519 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.519 Floors, decks, stairs, and ladders of on-track roadway maintenance machines. Floors, decks, stairs, and ladders of on-track roadway...

49 CFR 214.519 - Floors, decks, stairs, and ladders of on-track roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... roadway maintenance machines. 214.519 Section 214.519 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.519 Floors, decks, stairs, and ladders of on-track roadway maintenance machines. Floors, decks, stairs, and ladders of on-track roadway...

Control technology for integrated circuit fabrication at Micro-Circuit Engineering, Incorporated, West Palm Beach, Florida

NASA Astrophysics Data System (ADS)

Mihlan, G. I.; Mitchell, R. I.; Smith, R. K.

1984-07-01

A survey to assess control technology for integrated circuit fabrication was conducted. Engineering controls included local and general exhaust ventilation, shielding, and personal protective equipment. Devices or work stations that contained toxic materials that were potentially dangerous were controlled by local exhaust ventilation. Less hazardous areas were controlled by general exhaust ventilation. Process isolation was used in the plasma etching, low pressure chemical vapor deposition, and metallization operations. Shielding was used in ion implantation units to control X-ray emissions, in contact mask alignes to limit ultraviolet (UV) emissions, and in plasma etching units to control radiofrequency and UV emissions. Most operations were automated. Use of personal protective equipment varied by job function.

Hybrid-integrated coherent receiver using silica-based planar lightwave circuit technology

NASA Astrophysics Data System (ADS)

Kim, Jong-Hoi; Choe, Joong-Seon; Choi, Kwang-Seong; Youn, Chun-Ju; Kim, Duk-Jun; Jang, Sun-Hyok; Kwon, Yong-Hwan; Nam, Eun-Soo

2011-12-01

A hybrid-integrated coherent receiver module has been achieved using flip-chip bonding technology, consisting of a silica-based 90°-hybrid planar lightwave circuit (PLC) platform, a spot-size converter integrated waveguide photodiode (SSC-WG-PD), and a dual-channel transimpedance amplifier (TIA). The receiver module shows error-free operation up to 40Gb/s and OSNR sensitivity of 11.5 dB for BER = 10-3 at 25 Gb/s.

High Power Broadband Millimeter Wave TWTs

NASA Astrophysics Data System (ADS)

James, Bill G.

1998-04-01

In the early 1980's the requirement for high power broadband millimeter wave sources encouraged the development of microwave vacuum device amplifiers for radar and communication systems. Many government funded programs were implemented for the development of high power broadband millimeter wave amplifiers that would meet the needs of the high power community. The tube design capable of meeting these goals was the slow wave coupled cavity traveling wave device, which had a proven technology base at the lower frequencies (X Band). However scaling this technology to the millimeter frequencies had severe shortcomings in both thermal and manufacturing design. These shortcomings were overcome with the development of the Ladder Circuit technology. In conjunction with the circuit development high power electron beam systems had to be developed for the generation of high rf powers. These beam systems had to be capable of many megawatts of beam power density and high current densities. The cathode technology required to be capable of operating at current densities of 10 amperes per square centimeter at long pulse lengths and high duty cycle. Since the introduction of the Ladder Circuit technology a number of high power broadband millimeter wave amplifiers have been developed and deployed in operating radar and communication systems. Broadband millimeter wave sources have been manufactured in the frequency range from 27 GHz to 100 GHz with power levels ranging from 100 watts CW to 10 kilowatts Peak at W band over a 2 GHz bandwidth. Also a 50 kW peak power and 10 kW average power device at Ka band with 2 GHz bandwidth has been developed. Today the power levels achieved by these devices are nearing the limits of this technology; therefore to gain a significant increase in power at the millimeter wave frequencies, other technologies will have to be considered, particularly fast wave devices. This paper will briefly review the ladder circuit technology and present the designs of

7. DETAIL, WINDOWS AND SAFETY LADDER AT RECEIVING DEPARTMENT, NORTH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. DETAIL, WINDOWS AND SAFETY LADDER AT RECEIVING DEPARTMENT, NORTH SIDE, NEAR WEST END. - United Engineering Company Shipyard, Inspection & Repair Shops, 2900 Main Street, Alameda, Alameda County, CA

Clinical career ladders: the Moses H. Cone Memorial Hospital.

PubMed

Crouch, J B; Douglas, J B; Wheeler, D S

1989-11-01

A competence- and achievement-based advancement program developed for pharmacists at The Moses H. Cone Memorial Hospital, a 530-bed community teaching hospital, is described. In 1985 pharmacy management recognized the need to provide an incentive program to reward achievements by staff clinical pharmacists, recognize their increased responsibilities, and increase the department's ability to retain qualified practitioners. Adding another rung to the existing administrative career ladder was not desirable, so a new job category, pharmacist II, was created. Employees are evaluated for promotion to pharmacist II on the basis of tenure, performance, and elective professional and service activities. A point system is used to objectively score achievements; to be promoted, an employee must accumulate 50 points during a two-year period. The number of staff pharmacists who can advance is limited not arbitrarily but rather by the application of challenging criteria. Employees are responsible for submitting documentation of their achievements to a review committee, which meets quarterly to evaluate applications and award points. Of 13 applicants since 1985, 10 have been promoted. Because of problems in evaluating the performance of pharmacist II employees, providing them time to conduct research, and incorporating specialty practice areas into the program, plans are being made to institute a more structured career ladder system with separate managerial, clinical, and educational tracks. A competence- and achievement-based advancement program with a single step was an improvement over the former system but lacked the balance and comprehensiveness offered by more structured career ladder programs.

VLSI circuits implementing computational models of neocortical circuits.

PubMed

Wijekoon, Jayawan H B; Dudek, Piotr

2012-09-15

This paper overviews the design and implementation of three neuromorphic integrated circuits developed for the COLAMN ("Novel Computing Architecture for Cognitive Systems based on the Laminar Microcircuitry of the Neocortex") project. The circuits are implemented in a standard 0.35 μm CMOS technology and include spiking and bursting neuron models, and synapses with short-term (facilitating/depressing) and long-term (STDP and dopamine-modulated STDP) dynamics. They enable execution of complex nonlinear models in accelerated-time, as compared with biology, and with low power consumption. The neural dynamics are implemented using analogue circuit techniques, with digital asynchronous event-based input and output. The circuits provide configurable hardware blocks that can be used to simulate a variety of neural networks. The paper presents experimental results obtained from the fabricated devices, and discusses the advantages and disadvantages of the analogue circuit approach to computational neural modelling. Copyright © 2012 Elsevier B.V. All rights reserved.

The effects of Navy ship ladder descent on the knee internal joint reaction forces

NASA Astrophysics Data System (ADS)

Coulter, Jonathan D.; Weinhandl, Joshua T.; Bawab, Sebastian Y.; Ringleb, Stacie I.

2017-02-01

Military populations may be at risk for developing knee osteoarthritis and other knee problems when descending a Navy ship ladder, which differs from traditional stairs due to non-overlapping treads, a larger rise and a steeper inclination angle. The purpose of this study was to develop a forward dynamic model of the descent of a Navy ship ladder to determine how this motion affects the internal knee reaction forces and how altering the hamstring/quadriceps ratio affects the internal joint reaction forces in the knee. Kinematic and kinetic data were collected from three male sailors descending a replica of a Navy ship ladder and were used as input into a model constructed in OpenSim. The peak resultant joint reaction force was 6.6 × BW, which was greater than values reported in the literature in traditional stairs. Peak compressive and anterior joint reaction forces, 4.05 × BW and 5.46 × BW, respectively, were greater than reported values for a squat, a motion similar to descending a ship ladder. The average peak vertical and anterior internal joint reaction force at the knee were 4.05 × BW and 5.46 × BW, respectively. The resultant joint reaction forces calculated from the ladder descent were greater than stair descent and squatting. Little effects were found in the joint reaction forces after adjusting the quadriceps to hamstring muscle strength ratios, possibly because these ratios might change the distribution of the contact forces across the joint, not the resultant forces.

"Ladder" structure in tonal noise generated by laminar flow around an airfoil.

PubMed

Chong, Tze Pei; Joseph, Phillip

2012-06-01

The presence of a "ladder" structure in the airfoil tonal noise was discovered in the 1970s, but its mechanism hitherto remains a subject of continual investigation in the research community. Based on the measured noise results and some numerical analysis presented in this letter, the variations of four types of airfoil tonal noise frequencies with the flow velocity were analyzed individually. The ladder structure is proposed to be caused by the acoustic/hydrodynamic frequency lag between the scattering of the boundary layer instability noise and the discrete noise produced by an aeroacoustic feedback loop.

46 CFR 116.438 - Stairtowers, stairways, ladders, and elevators.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... (1) Stairways, stairtowers, ladders, elevators, and landings must be designed with sufficient... accommodation spaces: Designed capacity; (ii) Accommodation spaces having fixed seating for passengers: Maximum seating capacity; (iii) Public spaces, including spaces such as casinos, restaurants, club rooms, and...

Present Status of Power Circuit Breaker and its Future

NASA Astrophysics Data System (ADS)

Yoshioka, Yoshio

Gas circuit breaker and vacuum circuit breaker are the 2 main types of circuit breaker used in extra high voltage and medium voltage networks. After reviewing the history of these circuit breakers, their present status and technologies are described. As for future technology, computation of interrupting phenomena, SF6 gas less apparatus and expectation of the high voltage vacuum circuit breaker are discussed.

Assessment of Durable SiC JFET Technology for +600 C to -125 C Integrated Circuit Operation

NASA Technical Reports Server (NTRS)

Neudeck, P. G.; Krasowski, M. J.; Prokop, N. F.

2011-01-01

Electrical characteristics and circuit design considerations for prototype 6H-SiC JFET integrated circuits (ICs) operating over the broad temperature range of -125 C to +600 C are described. Strategic implementation of circuits with transistors and resistors in the same 6H-SiC n-channel layer enabled ICs with nearly temperature-independent functionality to be achieved. The frequency performance of the circuits declined at temperatures increasingly below or above room temperature, roughly corresponding to the change in 6H-SiC n-channel resistance arising from incomplete carrier ionization at low temperature and decreased electron mobility at high temperature. In addition to very broad temperature functionality, these simple digital and analog demonstration integrated circuits successfully operated with little change in functional characteristics over the course of thousands of hours at 500 C before experiencing interconnect-related failures. With appropriate further development, these initial results establish a new technology foundation for realizing durable 500 C ICs for combustion engine sensing and control, deep-well drilling, and other harsh-environment applications.

Clinical ladder program implementation: a project guide.

PubMed

Ko, Yu Kyung; Yu, Soyoung

2014-11-01

This article describes the development of a clinical ladder program (CLP) implementation linked to a promotion system for nurses. The CLP task force developed criteria for each level of performance and a performance evaluation tool reflecting the self-motivation of the applicant for professional development. One year after implementation, the number of nurses taking graduate courses increased, and 7 nurses were promoted to nurse manager positions.

29 CFR 1918.24 - Fixed and portable ladders.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., and be positively secured or held against shifting or slipping. When conditions are such that a... strength shall be furnished and positively secured or held against shifting or slipping while in use. Steps... securely positioned on a level and firm base. (2) Ladders shall be fitted with slip-resistant bases and/or...

29 CFR 1918.24 - Fixed and portable ladders.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and be positively secured or held against shifting or slipping. When conditions are such that a... strength shall be furnished and positively secured or held against shifting or slipping while in use. Steps... securely positioned on a level and firm base. (2) Ladders shall be fitted with slip-resistant bases and/or...

29 CFR 1918.24 - Fixed and portable ladders.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., and be positively secured or held against shifting or slipping. When conditions are such that a... strength shall be furnished and positively secured or held against shifting or slipping while in use. Steps... securely positioned on a level and firm base. (2) Ladders shall be fitted with slip-resistant bases and/or...

29 CFR 1918.24 - Fixed and portable ladders.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and be positively secured or held against shifting or slipping. When conditions are such that a... strength shall be furnished and positively secured or held against shifting or slipping while in use. Steps... securely positioned on a level and firm base. (2) Ladders shall be fitted with slip-resistant bases and/or...

29 CFR 1918.24 - Fixed and portable ladders.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., and be positively secured or held against shifting or slipping. When conditions are such that a... strength shall be furnished and positively secured or held against shifting or slipping while in use. Steps... securely positioned on a level and firm base. (2) Ladders shall be fitted with slip-resistant bases and/or...

Mask induction despite circuit obstruction: an unrecognized hazard of relying on automated machine check technology.

PubMed

Yang, Kamie K; Lewis, Ian H

2014-06-15

Various equipment malfunctions of anesthesia gas delivery systems have been previously reported. Our profession increasingly uses technology as a means to prevent these errors. We report a case of a near-total anesthesia circuit obstruction that went undetected before the induction of anesthesia despite the use of automated machine check technology. This case highlights that automated machine check modules can fail to detect severe equipment failure and demonstrates how, even in this era of expanding technology, manual checks still remain essential components of safe care.

Healthcare organization-education partnerships and career ladder programs for health care workers.

PubMed

Dill, Janette S; Chuang, Emmeline; Morgan, Jennifer C

2014-12-01

Increasing concerns about quality of care and workforce shortages have motivated health care organizations and educational institutions to partner to create career ladders for frontline health care workers. Career ladders reward workers for gains in skills and knowledge and may reduce the costs associated with turnover, improve patient care, and/or address projected shortages of certain nursing and allied health professions. This study examines partnerships between health care and educational organizations in the United States during the design and implementation of career ladder training programs for low-skill workers in health care settings, referred to as frontline health care workers. Mixed methods data from 291 frontline health care workers and 347 key informants (e.g., administrators, instructors, managers) collected between 2007 and 2010 were analyzed using both regression and fuzzy-set qualitative comparative analysis (QCA). Results suggest that different combinations of partner characteristics, including having an education leader, employer leader, frontline management support, partnership history, community need, and educational policies, were necessary for high worker career self-efficacy and program satisfaction. Whether a worker received a wage increase, however, was primarily dependent on leadership within the health care organization, including having an employer leader and employer implementation policies. Findings suggest that strong partnerships between health care and educational organizations can contribute to the successful implementation of career ladder programs, but workers' ability to earn monetary rewards for program participation depends on the strength of leadership support within the health care organization. Copyright © 2014 Elsevier Ltd. All rights reserved.

Nestling diets and provisioning rates of sympatric Golden-fronted and Ladder-backed Woodpeckers

USGS Publications Warehouse

Schroeder, Evonne L.; Boal, Clint W.; Glasscock, Selma N.

2013-01-01

We examined comparative food use and provisioning of Golden-fronted (Melanerpes aurifrons) and Ladder-backed (Picoides scalaris) woodpeckers at the Rob and Bessie Welder Wildlife Foundation Refuge, in San Patricio County, Texas. We combined video surveillance and direct observations to monitor provisioning rates and identify items delivered by adult woodpeckers to nestlings. We collected 328 hours of data at Ladder-backed Woodpecker nest cavities and 230 hours of data at Golden-fronted Woodpecker nest cavities. Ladder-backed Woodpecker nestling diets consisted of 100% animal matter, comprised of invertebrate larvae (99%) and invertebrate adults (< 1%). Diets of Golden-fronted Woodpecker nestlings were also high in animal matter (77%) with more invertebrate adults (55%) and fewer invertebrate larvae (27%), but also included vegetable matter (16%). Morisita's measure of overlap suggested a relatively low dietary overlap of 31% between nestlings of these two sympatric woodpecker species. Foraging methods used by these species may explain their low dietary overlap and facilitate their coexistence.

Phase diagram and re-entrant fermionic entanglement in a hybrid Ising-Hubbard ladder

NASA Astrophysics Data System (ADS)

Sousa, H. S.; Pereira, M. S. S.; de Oliveira, I. N.; Strečka, J.; Lyra, M. L.

2018-05-01

The degree of fermionic entanglement is examined in an exactly solvable Ising-Hubbard ladder, which involves interacting electrons on the ladder's rungs described by Hubbard dimers at half-filling on each rung, accounting for intrarung hopping and Coulomb terms. The coupling between neighboring Hubbard dimers is assumed to have an Ising-like nature. The ground-state phase diagram consists of four distinct regions corresponding to the saturated paramagnetic, the classical antiferromagnetic, the quantum antiferromagnetic, and the mixed classical-quantum phase. We have exactly computed the fermionic concurrence, which measures the degree of quantum entanglement between the pair of electrons on the ladder rungs. The effects of the hopping amplitude, the Coulomb term, temperature, and magnetic fields on the fermionic entanglement are explored in detail. It is shown that the fermionic concurrence displays a re-entrant behavior when quantum entanglement is being generated at moderate temperatures above the classical saturated paramagnetic ground state.

Polymorphic Electronic Circuits

NASA Technical Reports Server (NTRS)

Stoica, Adrian

2004-01-01

Polymorphic electronics is a nascent technological discipline that involves, among other things, designing the same circuit to perform different analog and/or digital functions under different conditions. For example, a circuit can be designed to function as an OR gate or an AND gate, depending on the temperature (see figure). Polymorphic electronics can also be considered a subset of polytronics, which is a broader technological discipline in which optical and possibly other information- processing systems could also be designed to perform multiple functions. Polytronics is an outgrowth of evolvable hardware (EHW). The basic concepts and some specific implementations of EHW were described in a number of previous NASA Tech Briefs articles. To recapitulate: The essence of EHW is to design, construct, and test a sequence of populations of circuits that function as incrementally better solutions of a given design problem through the selective, repetitive connection and/or disconnection of capacitors, transistors, amplifiers, inverters, and/or other circuit building blocks. The evolution is guided by a search-and-optimization algorithm (in particular, a genetic algorithm) that operates in the space of possible circuits to find a circuit that exhibits an acceptably close approximation of the desired functionality. The evolved circuits can be tested by computational simulation (in which case the evolution is said to be extrinsic), tested in real hardware (in which case the evolution is said to be intrinsic), or tested in random sequences of computational simulation and real hardware (in which case the evolution is said to be mixtrinsic).

Plaquette order in a dimerized frustrated spin ladder

NASA Astrophysics Data System (ADS)

Shlagman, Ofer; Shimshoni, Efrat

2014-11-01

We study the effect of dimerization (due to, e.g., spin-Peierls instability) on the phase diagram of a frustrated antiferromagnetic spin-1/2 ladder, with weak transverse and diagonal rung coupling. Our analysis focuses on a one-dimensional version of the model (i.e., a single two-leg ladder) where we consider two forms of dimerization on the legs: columnar dimers (CDs) and staggered dimers (SDs). We examine in particular the regime of parameters (corresponding to an intermediate X X Z anisotropy) in which the leg dimerization and the rung coupling terms are equally relevant. In both the CD and SD cases, we find that the effective field theory describing the system is a self-dual sine-Gordon model, which favors ordering and the opening of a gap to excitations. The order parameter, which reflects the interplay between the leg and rung dimerization interactions, represents a crystal of 4-spin plaquettes on which longitudinal and transverse dimers are in a coherent superposition. Depending on the leg dimerization mode, these plaquettes are closed or open, however both types spontaneously break reflection symmetry across the ladder. The closed plaquettes are stable, while the open plaquette order is relatively fragile and the corresponding gap may be tuned to zero under extreme conditions. We further find that a first-order transition occurs from the plaquette order to a valence bond crystal (VBC) of dimers on the legs. This suggests that in a higher-dimensional version of this system, this variety of distinct VBC states with comparable energies leads to the formation of domains. Effectively one-dimensional gapless spinon modes on domain boundaries may account for the experimental observation of spin-liquid behavior in a physical realization of the model.

Television Equipment Repair Career Ladder. Occupational Survey Report.

ERIC Educational Resources Information Center

Air Force Occupational Measurement Center, Lackland AFB, TX.

The report describes the results of an Air Force occupational survey of the television equipment repair career ladder. A job inventory, administered to 808 job incumbents, consisted of a background information section and a duty-task list designed to assess the relative amount of time spent on tasks performed in current jobs. The resulting…

Analytical recursive method to ascertain multisite entanglement in doped quantum spin ladders

NASA Astrophysics Data System (ADS)

Roy, Sudipto Singha; Dhar, Himadri Shekhar; Rakshit, Debraj; SenDe, Aditi; Sen, Ujjwal

2017-08-01

We formulate an analytical recursive method to generate the wave function of doped short-range resonating valence bond (RVB) states as a tool to efficiently estimate multisite entanglement as well as other physical quantities in doped quantum spin ladders. We prove that doped RVB ladder states are always genuine multipartite entangled. Importantly, our results show that within specific doping concentration and model parameter regimes, the doped RVB state essentially characterizes the trends of genuine multiparty entanglement in the exact ground states of the Hubbard model with large on-site interactions, in the limit that yields the t -J Hamiltonian.

Bound States and Field-Polarized Haldane Modes in a Quantum Spin Ladder.

PubMed

Ward, S; Mena, M; Bouillot, P; Kollath, C; Giamarchi, T; Schmidt, K P; Normand, B; Krämer, K W; Biner, D; Bewley, R; Guidi, T; Boehm, M; McMorrow, D F; Rüegg, Ch

2017-04-28

The challenge of one-dimensional systems is to understand their physics beyond the level of known elementary excitations. By high-resolution neutron spectroscopy in a quantum spin-ladder material, we probe the leading multiparticle excitation by characterizing the two-magnon bound state at zero field. By applying high magnetic fields, we create and select the singlet (longitudinal) and triplet (transverse) excitations of the fully spin-polarized ladder, which have not been observed previously and are close analogs of the modes anticipated in a polarized Haldane chain. Theoretical modeling of the dynamical response demonstrates our complete quantitative understanding of these states.

77 FR 15839 - Culturally Significant Objects Imported for Exhibition Determinations: “Joan Miró: the Ladder of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-16

... DEPARTMENT OF STATE [Public Notice 7827] Culturally Significant Objects Imported for Exhibition Determinations: ``Joan Mir[oacute]: the Ladder of Escape'' SUMMARY: Notice is hereby given of the following... exhibition ``Joan Mir[oacute]: the Ladder of Escape,'' imported from abroad for temporary exhibition within...

In-line digital holography with phase-shifting Greek-ladder sieves

NASA Astrophysics Data System (ADS)

Xie, Jing; Zhang, Junyong; Zhang, Yanli; Zhou, Shenlei; Zhu, Jianqiang

2018-04-01

Phase shifting is the key technique in in-line digital holography, but traditional phase shifters have their own limitations in short wavelength regions. Here, phase-shifting Greek-ladder sieves with amplitude-only modulation are introduced into in-line digital holography, which are essentially a kind of diffraction lens with three-dimensional array diffraction-limited foci. In the in-line digital holographic experiment, we design two kinds of sieves by lithography and verify the validity of their phase-shifting function by measuring a 1951 U.S. Air Force resolution test target and three-dimensional array foci. With advantages of high resolving power, low cost, and no limitations at shorter wavelengths, phase-shifting Greek-ladder sieves have great potential in X-ray holography or biochemical microscopy for the next generation of synchrotron light sources.

Observation hall along west side. Looking south to escape ladder. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Observation hall along west side. Looking south to escape ladder. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Instrumentation & Control Building, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

The snakes and ladders of National Health Service management in England.

PubMed

Powell, Martin

2014-01-01

This article explores managerial careers in the National Health Service (NHS) through the lens of talent management, particularly focusing on how managers view barriers (snakes) and facilitators (ladders) to career progression. There is a significant literature on enablers and barriers to career progression, but much of this focuses on specific groups such as black and minority ethnic and female workers, and there is relatively little material on the general workforce of the NHS. The research design is a mixed method quantitative (questionnaire) and qualitative (interview and focus group) approach consisting of a quasi-probability element that focuses on a maximum variety sample and a purposive element that seeks policy views at central and strategic health authority level, and examines talent management in high-performing NHS organisations. Ladders are identified as follows: volunteering, secondment, networking, mentoring, academic qualifications, development, good role models/managers and appraisal/personal development plan. Snakes are identified as managing expectations; identity and cognitive diversity; location; sector; NHS toxic and favouritism culture; poor talent spotting; credentialism; exclusive approach to talent; and sustainability. It concludes that while previous conceptual and empirical work is fairly clear on any ladders, it is less clear on snakes. Copyright © 2013 John Wiley & Sons, Ltd.

A "Career Ladder" Approach to Junior College Curriculum.

ERIC Educational Resources Information Center

Schrupp, Harold A.

More attention should be paid to the building of career guidance and career curriculum programs with exit points that enable the student to seek employment at any time in an entry level position and/or to continue his education. Some of the best "career ladder" programs are the federally sponsored New Career programs. A number of the…

Schroedinger operators with the q-ladder symmetry algebras

NASA Technical Reports Server (NTRS)

Skorik, Sergei; Spiridonov, Vyacheslav

1994-01-01

A class of the one-dimensional Schroedinger operators L with the symmetry algebra LB(+/-) = q(+/-2)B(+/-)L, (B(+),B(-)) = P(sub N)(L), is described. Here B(+/-) are the 'q-ladder' operators and P(sub N)(L) is a polynomial of the order N. Peculiarities of the coherent states of this algebra are briefly discussed.

Recent Progress in the Development of Printed Thin-Film Transistors and Circuits with High-Resolution Printing Technology.

PubMed

Fukuda, Kenjiro; Someya, Takao

2017-07-01

Printed electronics enable the fabrication of large-scale, low-cost electronic devices and systems, and thus offer significant possibilities in terms of developing new electronics/optics applications in various fields. Almost all electronic applications require information processing using logic circuits. Hence, realizing the high-speed operation of logic circuits is also important for printed devices. This report summarizes recent progress in the development of printed thin-film transistors (TFTs) and integrated circuits in terms of materials, printing technologies, and applications. The first part of this report gives an overview of the development of functional inks such as semiconductors, electrodes, and dielectrics. The second part discusses high-resolution printing technologies and strategies to enable high-resolution patterning. The main focus of this report is on obtaining printed electrodes with high-resolution patterning and the electrical performance of printed TFTs using such printed electrodes. In the final part, some applications of printed electronics are introduced to exemplify their potential. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

4H-SiC JFET Multilayer Integrated Circuit Technologies Tested Up to 1000 K

NASA Technical Reports Server (NTRS)

Spry, D. J.; Neudeck, P. G.; Chen, L.; Chang, C. W.; Lukco, D.; Beheim, G. M.

2015-01-01

Testing of semiconductor electronics at temperatures above their designed operating envelope is recognized as vital to qualification and lifetime prediction of circuits. This work describes the high temperature electrical testing of prototype 4H silicon carbide (SiC) junction field effect transistor (JFET) integrated circuits (ICs) technology implemented with multilayer interconnects; these ICs are intended for prolonged operation at temperatures up to 773K (500 C). A 50 mm diameter sapphire wafer was used in place of the standard NASA packaging for this experiment. Testing was carried out between 300K (27 C) and 1150K (877 C) with successful electrical operation of all devices observed up to 1000K (727 C).

Ladder operators and coherent states for the Jaynes-Cummings model in the rotating-wave approximation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hussin, V.; Nieto, L.M.

2005-12-15

Using algebraic techniques, we realize a systematic search of different types of ladder operators for the Jaynes-Cummings model in the rotating-wave approximation. The link between our results and previous studies on the diagonalization of the associated Hamiltonian is established. Using some of the ladder operators obtained before, examples are given on the possibility of constructing a variety of interesting coherent states for this Hamiltonian.

Intermetallic compounds in 3D integrated circuits technology: a brief review

NASA Astrophysics Data System (ADS)

Annuar, Syahira; Mahmoodian, Reza; Hamdi, Mohd; Tu, King-Ning

2017-12-01

The high performance and downsizing technology of three-dimensional integrated circuits (3D-ICs) for mobile consumer electronic products have gained much attention in the microelectronics industry. This has been driven by the utilization of chip stacking by through-Si-via and solder microbumps. Pb-free solder microbumps are intended to replace conventional Pb-containing solder joints due to the rising awareness of environmental preservation. The use of low-volume solder microbumps has led to crucial constraints that cause several reliability issues, including excessive intermetallic compounds (IMCs) formation and solder microbump embrittlement due to IMCs growth. This article reviews technologies related to 3D-ICs, IMCs formation mechanisms and reliability issues concerning IMCs with Pb-free solder microbumps. Finally, future outlook on the potential growth of research in this area is discussed.

Intermetallic compounds in 3D integrated circuits technology: a brief review

PubMed Central

Annuar, Syahira; Mahmoodian, Reza; Hamdi, Mohd; Tu, King-Ning

2017-01-01

Abstract The high performance and downsizing technology of three-dimensional integrated circuits (3D-ICs) for mobile consumer electronic products have gained much attention in the microelectronics industry. This has been driven by the utilization of chip stacking by through-Si-via and solder microbumps. Pb-free solder microbumps are intended to replace conventional Pb-containing solder joints due to the rising awareness of environmental preservation. The use of low-volume solder microbumps has led to crucial constraints that cause several reliability issues, including excessive intermetallic compounds (IMCs) formation and solder microbump embrittlement due to IMCs growth. This article reviews technologies related to 3D-ICs, IMCs formation mechanisms and reliability issues concerning IMCs with Pb-free solder microbumps. Finally, future outlook on the potential growth of research in this area is discussed. PMID:29057024

Intermetallic compounds in 3D integrated circuits technology: a brief review.

PubMed

Annuar, Syahira; Mahmoodian, Reza; Hamdi, Mohd; Tu, King-Ning

2017-01-01

The high performance and downsizing technology of three-dimensional integrated circuits (3D-ICs) for mobile consumer electronic products have gained much attention in the microelectronics industry. This has been driven by the utilization of chip stacking by through-Si-via and solder microbumps. Pb-free solder microbumps are intended to replace conventional Pb-containing solder joints due to the rising awareness of environmental preservation. The use of low-volume solder microbumps has led to crucial constraints that cause several reliability issues, including excessive intermetallic compounds (IMCs) formation and solder microbump embrittlement due to IMCs growth. This article reviews technologies related to 3D-ICs, IMCs formation mechanisms and reliability issues concerning IMCs with Pb-free solder microbumps. Finally, future outlook on the potential growth of research in this area is discussed.

High-Performance WSe2 Complementary Metal Oxide Semiconductor Technology and Integrated Circuits.

PubMed

Yu, Lili; Zubair, Ahmad; Santos, Elton J G; Zhang, Xu; Lin, Yuxuan; Zhang, Yuhao; Palacios, Tomás

2015-08-12

Because of their extraordinary structural and electrical properties, two-dimensional materials are currently being pursued for applications such as thin-film transistors and integrated circuit. One of the main challenges that still needs to be overcome for these applications is the fabrication of air-stable transistors with industry-compatible complementary metal oxide semiconductor (CMOS) technology. In this work, we experimentally demonstrate a novel high performance air-stable WSe2 CMOS technology with almost ideal voltage transfer characteristic, full logic swing and high noise margin with different supply voltages. More importantly, the inverter shows large voltage gain (∼38) and small static power (picowatts), paving the way for low power electronic system in 2D materials.

LEANTO INTERIOR, LOOKING EAST. Image shows: ladder attached to south ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

LEAN-TO INTERIOR, LOOKING EAST. Image shows: ladder attached to south façade, gate separating hay storage from animal pens, and east wall construction. - Boyer Farm, Barn, 711 South Fort Casey Road, Coupeville, Island County, WA

Pressure-induced superconductivity in the iron-based ladder material BaFe2S3.

PubMed

Takahashi, Hiroki; Sugimoto, Akira; Nambu, Yusuke; Yamauchi, Touru; Hirata, Yasuyuki; Kawakami, Takateru; Avdeev, Maxim; Matsubayashi, Kazuyuki; Du, Fei; Kawashima, Chizuru; Soeda, Hideto; Nakano, Satoshi; Uwatoko, Yoshiya; Ueda, Yutaka; Sato, Taku J; Ohgushi, Kenya

2015-10-01

All the iron-based superconductors identified so far share a square lattice composed of Fe atoms as a common feature, despite having different crystal structures. In copper-based materials, the superconducting phase emerges not only in square-lattice structures but also in ladder structures. Yet iron-based superconductors without a square-lattice motif have not been found, despite being actively sought out. Here, we report the discovery of pressure-induced superconductivity in the iron-based spin-ladder material BaFe2S3, a Mott insulator with striped-type magnetic ordering below ∼120 K. On the application of pressure this compound exhibits a metal-insulator transition at about 11 GPa, followed by the appearance of superconductivity below Tc = 14 K, right after the onset of the metallic phase. Our findings indicate that iron-based ladder compounds represent promising material platforms, in particular for studying the fundamentals of iron-based superconductivity.

A circuit model for nonlinear simulation of radio-frequency filters using bulk acoustic wave resonators.

PubMed

Ueda, Masanori; Iwaki, Masafumi; Nishihara, Tokihiro; Satoh, Yoshio; Hashimoto, Ken-ya

2008-04-01

This paper describes a circuit model for the analysis of nonlinearity in the filters based on radiofrequency (RF) bulk acoustic wave (BAW) resonators. The nonlinear output is expressed by a current source connected parallel to the linear resonator. Amplitude of the nonlinear current source is programmed proportional to the product of linear currents flowing in the resonator. Thus, the nonlinear analysis is performed by the common linear analysis, even for complex device structures. The analysis is applied to a ladder-type RF BAW filter, and frequency dependence of the nonlinear output is discussed. Furthermore, this analysis is verified through comparison with experiments.

Creating a Professional Ladder for Interpreters for Improvement of Care.

PubMed

Marshall, Lori; Fischer, Anna; Noyes Soeller, Allison; Cordova, Richard; Gutierrez, Yvonne R; Alford, Luis

2016-01-01

Children's Hospital Los Angeles (CHLA), a metropolitan academic medical center, recognized limitations in how the professional interpreters from the Diversity Services Department were used to support effective patient-provider communication across the organization. Given the importance of mitigating language and communication barriers, CHLA sought to minimize clinical and structural barriers to health care for limited English proficiency populations through a comprehensive restructuring of the Diversity Services Department. This approach entailed a new delivery model for hospital language assistance and cultural consultancy resources. The intervention focused on restructuring the Diversity Services Department, redefining priorities, reallocating resources, and redefining the roles of the language staff positions in the department. The language staff role was redesigned to fit a four-level professional career ladder modeled after the professional career ladders commonly used in hospitals for the RN role and other professional disciplines. The approach involved creating new levels of language specialist, each with progressive requirements for performance, leadership, and accountability for patient care outcomes. Language staff in the inpatient, clinic, and emergency department settings worked alongside nurses, physicians, and other disciplines to care for a specific set of patients. The result of this work was a positive culture change resulting in service efficiencies, care improvements, and improved access to language services. A professional career ladder for language staff contributed to improving the quality and access of language services and advancing the interpreting profession by incorporating care coordination support, vital document translation, and cultural consultancy.

Methods of fabricating applique circuits

DOEpatents

Dimos, Duane B.; Garino, Terry J.

1999-09-14

Applique circuits suitable for advanced packaging applications are introduced. These structures are particularly suited for the simple integration of large amounts (many nanoFarads) of capacitance into conventional integrated circuit and multichip packaging technology. In operation, applique circuits are bonded to the integrated circuit or other appropriate structure at the point where the capacitance is required, thereby minimizing the effects of parasitic coupling. An immediate application is to problems of noise reduction and control in modern high-frequency circuitry.

A Virtual Circuits Lab

ERIC Educational Resources Information Center

Vick, Matthew E.

2010-01-01

The University of Colorado's Physics Education Technology (PhET) website offers free, high-quality simulations of many physics experiments that can be used in the classroom. The Circuit Construction Kit, for example, allows students to safely and constructively play with circuit components while learning the mathematics behind many circuit…

Ground Radio Operator Career Ladder AFSC 293X3.

DTIC Science & Technology

1981-07-01

formal resident training, OJT, and ,her Air Force management decisions . The structure of jobs within the Ground ! odio Operatoi career ladder was...33 ADJUST ANTENNA TUNING UNITS 33 TYPE RECORDS, REPORTS, OR FORMS :33 OPERATE AUXILLARY GENERATORS 33 A8 ’iT’ TASKS PERFORMED BY SUPERVISORS AND

Ladder Operators for Some Spherically Symmetric Potentials in Quantum Mechanics

ERIC Educational Resources Information Center

Newmarch, J. D.; Golding, R. M.

1978-01-01

The energy levels of the free field, Coulomb potential, and the three-dimensional harmonic oscillator are found using the Dirac operator formalism by the construction of suitable ladder operators. The degeneracy of each level is also discussed. (Author/GA)

Investigation of electronic transport through a ladder-like graphene nanoribbon including random distributed impurities

NASA Astrophysics Data System (ADS)

Esmaili, Esmat; Mardaani, Mohammad; Rabani, Hassan

2018-01-01

The electronic transport of a ladder-like graphene nanoribbon which the on-site or hopping energies of a small part of it can be random is modeled by using the Green's function technique within the nearest neighbor tight-binding approach. We employ a unitary transformation in order to convert the Hamiltonian of the nanoribbon to the Hamiltonian of a tight-binding ladder-like network. In this case, the disturbed part of the system includes the second neighbor hopping interactions. While, the converted Hamiltonian of each ideal part is equivalent to the Hamiltonian of two periodic on-site chains. Therefore, we can insert the self-energies of the alternative on-site tight-binding chains to the inverse of the Green's function matrix of the ladder-like part. In this viewpoint, the conductance is constructed from two trans and cis contributions. The results show that increasing the disorder strength causes the increase and decrease of the conductance of the trans and cis contributions, respectively.

Diffused Silicon Transistors and Switches (1954-55): The Beginning of Integrated Circuit Technology

NASA Astrophysics Data System (ADS)

Holonyak, N.

2003-09-01

Silicon (Si) transistor and integrated circuit (IC) technology has grown so big, and become so important, that it is now hard to recognize where, apart from the invention of the transistor itself (Bardeen and Brattain, Dec 16, 1947), it had its origin. In spite of obvious differences in Ge and Si, in 1950-55 it was not evident in many laboratories, concentrating only on Ge, what form of Ge transistor (grown, alloyed, jet-etched, etc.) might be expected to prevail, with Si not even being considered (or being dismissed outright). What was the need for Si and, at the time, such a seemingly intractable peculiar new technology? The requirement on switching devices of low leakage, and thus the need to leave Ge in favor of Si, led directly in 1954-55 (Bell Telephone Laboratories, BTL) to the exploration of impurity-diffusion and metallization technology to realize Si transistors and p-n-p-n switches. This technology, a more or less ideal thin-layer technology that can be referenced from a single surface (and which indeed has proven to be basically invariant and constantly growing), led further to the discovery (1955) of the protective Si oxide, oxide masking and patterning, and the fundamental basis of the integrated circuit (i.e., device-to-device interconnection by patterned metallization across the oxide). We recount some of the exploratory diffused-impurity Si device development of 1954-55 at BTL, particularly the work in and near Moll's group, that helped to establish the basis for today's electronics. The Si diffused-impurity devices of 1954-55 are described, including work and data not previously reported or broadly known—in fact, much work and data (a new technology) that was carried across the Country to a place that became known as Silicon Valley. For further perspective, an appendix is included of independent early suggestions of Bardeen (Urbana notebook, Feb 1952) to leave Ge in favor of diffused Si devices.

Doping evolution of charge and spin excitations in two-leg Hubbard ladders: Comparing DMRG and FLEX results [Doping evolution of charge and spin excitations in two-leg Hubbard ladders: Comparing DMRG and RPA+FLEX results

DOE PAGES

Nocera, Alberto; Wang, Yan; Patel, Niravkumar D.; ...

2018-05-31

Here, we study the magnetic and charge dynamical response of a Hubbard model in a two-leg ladder geometry using the density matrix renormalization group (DMRG) method and the random phase approximation within the fluctuation-exchange approximation (FLEX). Our calculations reveal that FLEX can capture the main features of the magnetic response from weak up to intermediate Hubbard repulsion for doped ladders, when compared with the numerically exact DMRG results. However, while at weak Hubbard repulsion both the spin and charge spectra can be understood in terms of weakly interacting electron-hole excitations across the Fermi surface, at intermediate coupling DMRG shows gappedmore » spin excitations at large momentum transfer that remain gapless within the FLEX approximation. For the charge response, FLEX can only reproduce the main features of the DMRG spectra at weak coupling and high doping levels, while it shows an incoherent character away from this limit. Overall, our analysis shows that FLEX works surprisingly well for spin excitations at weak and intermediate Hubbard U values even in the difficult low-dimensional geometry such as a two-leg ladder. Finally, we discuss the implications of our results for neutron scattering and resonant inelastic x-ray scattering experiments on two-leg ladder cuprate compounds.« less

Doping evolution of charge and spin excitations in two-leg Hubbard ladders: Comparing DMRG and FLEX results [Doping evolution of charge and spin excitations in two-leg Hubbard ladders: Comparing DMRG and RPA+FLEX results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nocera, Alberto; Wang, Yan; Patel, Niravkumar D.

Here, we study the magnetic and charge dynamical response of a Hubbard model in a two-leg ladder geometry using the density matrix renormalization group (DMRG) method and the random phase approximation within the fluctuation-exchange approximation (FLEX). Our calculations reveal that FLEX can capture the main features of the magnetic response from weak up to intermediate Hubbard repulsion for doped ladders, when compared with the numerically exact DMRG results. However, while at weak Hubbard repulsion both the spin and charge spectra can be understood in terms of weakly interacting electron-hole excitations across the Fermi surface, at intermediate coupling DMRG shows gappedmore » spin excitations at large momentum transfer that remain gapless within the FLEX approximation. For the charge response, FLEX can only reproduce the main features of the DMRG spectra at weak coupling and high doping levels, while it shows an incoherent character away from this limit. Overall, our analysis shows that FLEX works surprisingly well for spin excitations at weak and intermediate Hubbard U values even in the difficult low-dimensional geometry such as a two-leg ladder. Finally, we discuss the implications of our results for neutron scattering and resonant inelastic x-ray scattering experiments on two-leg ladder cuprate compounds.« less

Electronic control circuits: A compilation

NASA Technical Reports Server (NTRS)

1973-01-01

A compilation of technical R and D information on circuits and modular subassemblies is presented as a part of a technology utilization program. Fundamental design principles and applications are given. Electronic control circuits discussed include: anti-noise circuit; ground protection device for bioinstrumentation; temperature compensation for operational amplifiers; hybrid gatling capacitor; automatic signal range control; integrated clock-switching control; and precision voltage tolerance detector.

37. INTERIOR VIEW OF TANK FROM THE TOP, SHOWING LADDERS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

37. INTERIOR VIEW OF TANK FROM THE TOP, SHOWING LADDERS ON SIDES AND THE WATERTIGHT DOOR OF THE 18-FOOT LOCK No date - U.S. Naval Submarine Base, New London Submarine Escape Training Tank, Albacore & Darter Roads, Groton, New London County, CT

New insights into the origin of ladder dikes: Implications for punctuated growth and crystal accumulation in the Cathedral Peak granodiorite

NASA Astrophysics Data System (ADS)

Wiebe, R. A.; Jellinek, A. M.; Hodge, K. F.

2017-04-01

Ladder dikes are steep tabular bodies, typically a meter or less thick, composed of moderately dipping, concave upward, alternating dark (i.e. schlieren) and light bands oriented roughly perpendicular to the ladder dike margins. These structures occur widely but sparsely in granitic rocks and are found prominently in the Cathedral Peak granodiorite (CPG) of the Tuolumne Intrusive suite. Previous studies have interpreted that ladder dikes form as a result of processes including the downward flow of crystal mush in cracks within strong crystal mush or by upward flow in steep tubes that migrate within a strong crystal mush. Our new observations indicate that ladder dikes formed by downward flow of crystal mush in troughs or valleys, in a manner potentially comparable to trough bands in mafic layered intrusions. Extensions of the schlieren outward and upward away from the ladder dike margins into the host granite demonstrate that the host granite was deposited as mounds on both sides at the same time as the ladder dikes. Ladder dikes, therefore, record lateral flows of crystal mush on a magma chamber floor. Vertical exposures suggest these flows are on the order of ten meters thick. Some steep exposures on granite domes indicate multiple ladder dikes (and flows) over a stratigraphic height of 80-100 m. Later (stratigraphically higher) flows commonly deform and erode the top of an earlier flow, and granitic material rich in K-feldspar megacrysts has locally engulfed large blocks of ladder dikes, demonstrating that the megacrysts were also transported in flows. Flows in the CPG are directed away from the center of the pluton toward the western and eastern margins and apparently spread along a strong crystal mush floor and into a rheologically complex CPG magma. Whereas established dynamical models for spreading (single phase) gravity currents with simple and complex rheologies explain the elongate geometry, spacing and orientation of the tabular bodies, the origin and

Microwave monolithic integrated circuit-related metrology at the National Institute of Standards and Technology

NASA Astrophysics Data System (ADS)

Reeve, Gerome; Marks, Roger; Blackburn, David

1990-12-01

How the National Institute of Standards and Technology (NIST) interacts with the GaAs community and the Defense Advanced Research Projects Agency microwave monolithic integrated circuit (MMIC) initiative is described. The organization of a joint industry and government laboratory consortium for MMIC-related metrology research is described along with some of the initial technical developments at NIST done in support of the consortium.

Stimulated emission from ladder-type two-photon coherent atomic ensemble.

PubMed

Park, Jiho; Moon, Han Seb

2018-05-28

We investigated the stimulated emission from a ladder-type two-photon coherent atomic ensemble, for the 5S 1/2 - 5P 3/2 - 5D 5/2 transition of 87 Rb atoms. Under the ladder-type two-photon resonance condition obtained using pump and coupling lasers, we observed broad four-wave mixing (FWM) light stimulated from two-photon coherence induced by the seed laser coupled between the ground state of 5S 1/2 and the first excited state of 5P 3/2 . A dip in the FWM spectrum was obtained for three-photon resonance due to V-type two-photon coherence using the pump and seed lasers. From the FWM spectra obtained for varying frequency detuning and seed-laser power, we determined that the seed laser acts as a stimulator for FWM generation, but also acts as a disturber of FWM due to V-type two-photon coherence.

Two-point resistance of the Möbius ladder

NASA Astrophysics Data System (ADS)

Chair, Noureddine; Dannoun, Elham Mohammed Ali

2015-03-01

Exact formulas for the two-point resistance and the Kirchhoff index of the Möbius ladder are given based on the recently developed analytical approach by Chair (2012 Ann. Phys. 327 2899). The expression for the two-point resistance is written in terms of the two-point resistance of N/2-cycle graph and the Bejaia and the Pisa numbers recently introduced by the first author.

Interplay of localized pyrene chromophores and π-conjugation in novel poly(2,7-pyrene) ladder polymers

NASA Astrophysics Data System (ADS)

Rudnick, Alexander; Kass, Kim-Julia; Preis, Eduard; Scherf, Ullrich; Bässler, Heinz; Köhler, Anna

2017-05-01

We present a detailed spectroscopic study, along with the synthesis, of conjugated, ladder-type 2,7-linked poly(pyrene)s. We observe a delocalization of the first singlet excited state along the polymer backbone, i.e., across the 2,7 linkage in the pyrene moiety, in contrast to earlier studies on conjugated 2,7-linked poly(pyrene)s without ladder structure. The electronic signature of the pyrene unit is, however, manifested in an increased lifetime and reduced oscillator strength as well as a modified vibronic progression in absorption of the singlet state compared to a ladder-type poly(para-phenylene) (MeLPPP). Furthermore, the reduced oscillator strength and increased lifetime slow down Förster-type energy transfer in films, where this transfer occurs to sites with increasing inter-chain coupling of H-type nature.

Broken Time-Reversal Symmetry in Strongly Correlated Ladder Structures

NASA Astrophysics Data System (ADS)

Troyer, Matthias

2004-03-01

A decade after the first detailed numerical investigations of strongly correlated ladder models, exotic and interesting phases are still being discovered. Besides charge and spin density wave states with broken translational symmetry, and resonating valence bond (RVB) type superconductivity, a time reversal symmetry borken phase was recently found at half filling [J.B. Marston et al., Phys. Rev. Lett 89, 056404 (2002)]. In this talk I will present our recent results of density matrix renormalization group (DMRG) calculations [Phys. Rev. Lett. 90, 186401 (2003)], where we provide, for the first time, in a doped strongly correlated system (two-leg ladder), a controlled theoretical demonstration of the existence of this state in which long-range ordered orbital currents are arranged in a staggered pattern. This phase, which we found to coexist with a charge density wave, is known in the literature under the names ``staggered flux phase'', ``orbital antiferromagnetism'' or ``d-density wave (DDW)''. This brings us closer to recent proposals that this order might be realized in the enigmatic pseudogap phase of the cuprate high temperature superconductors.

Advances in two photon scanning and scanless microscopy technologies for functional neural circuit imaging.

PubMed

Schultz, Simon R; Copeland, Caroline S; Foust, Amanda J; Quicke, Peter; Schuck, Renaud

2017-01-01

Recent years have seen substantial developments in technology for imaging neural circuits, raising the prospect of large scale imaging studies of neural populations involved in information processing, with the potential to lead to step changes in our understanding of brain function and dysfunction. In this article we will review some key recent advances: improved fluorophores for single cell resolution functional neuroimaging using a two photon microscope; improved approaches to the problem of scanning active circuits; and the prospect of scanless microscopes which overcome some of the bandwidth limitations of current imaging techniques. These advances in technology for experimental neuroscience have in themselves led to technical challenges, such as the need for the development of novel signal processing and data analysis tools in order to make the most of the new experimental tools. We review recent work in some active topics, such as region of interest segmentation algorithms capable of demixing overlapping signals, and new highly accurate algorithms for calcium transient detection. These advances motivate the development of new data analysis tools capable of dealing with spatial or spatiotemporal patterns of neural activity, that scale well with pattern size.

Advances in two photon scanning and scanless microscopy technologies for functional neural circuit imaging

PubMed Central

Schultz, Simon R.; Copeland, Caroline S.; Foust, Amanda J.; Quicke, Peter; Schuck, Renaud

2017-01-01

Recent years have seen substantial developments in technology for imaging neural circuits, raising the prospect of large scale imaging studies of neural populations involved in information processing, with the potential to lead to step changes in our understanding of brain function and dysfunction. In this article we will review some key recent advances: improved fluorophores for single cell resolution functional neuroimaging using a two photon microscope; improved approaches to the problem of scanning active circuits; and the prospect of scanless microscopes which overcome some of the bandwidth limitations of current imaging techniques. These advances in technology for experimental neuroscience have in themselves led to technical challenges, such as the need for the development of novel signal processing and data analysis tools in order to make the most of the new experimental tools. We review recent work in some active topics, such as region of interest segmentation algorithms capable of demixing overlapping signals, and new highly accurate algorithms for calcium transient detection. These advances motivate the development of new data analysis tools capable of dealing with spatial or spatiotemporal patterns of neural activity, that scale well with pattern size. PMID:28757657

The dc power circuits: A compilation

NASA Technical Reports Server (NTRS)

1972-01-01

A compilation of reports concerning power circuits is presented for the dissemination of aerospace information to the general public as part of the NASA Technology Utilization Program. The descriptions for the electronic circuits are grouped as follows: dc power supplies, power converters, current-voltage power supply regulators, overload protection circuits, and dc constant current power supplies.

Commercialisation of CMOS integrated circuit technology in multi-electrode arrays for neuroscience and cell-based biosensors.

PubMed

Graham, Anthony H D; Robbins, Jon; Bowen, Chris R; Taylor, John

2011-01-01

The adaptation of standard integrated circuit (IC) technology as a transducer in cell-based biosensors in drug discovery pharmacology, neural interface systems and electrophysiology requires electrodes that are electrochemically stable, biocompatible and affordable. Unfortunately, the ubiquitous Complementary Metal Oxide Semiconductor (CMOS) IC technology does not meet the first of these requirements. For devices intended only for research, modification of CMOS by post-processing using cleanroom facilities has been achieved. However, to enable adoption of CMOS as a basis for commercial biosensors, the economies of scale of CMOS fabrication must be maintained by using only low-cost post-processing techniques. This review highlights the methodologies employed in cell-based biosensor design where CMOS-based integrated circuits (ICs) form an integral part of the transducer system. Particular emphasis will be placed on the application of multi-electrode arrays for in vitro neuroscience applications. Identifying suitable IC packaging methods presents further significant challenges when considering specific applications. The various challenges and difficulties are reviewed and some potential solutions are presented.

Undergraduate Education: An Essential Rung on the Rehabilitation Career Ladder

ERIC Educational Resources Information Center

Evenson, Tom; Holloway, Linda

2007-01-01

This article presents the historical pertinence of undergraduate education to developing a career ladder within the field of vocational rehabilitation. Support for the relevance is presented through the results of an investigation of baccalaureate-level competence and preparation as perceived by graduates of rehabilitation services programs. Job…

Compact Circuit Preprocesses Accelerometer Output

NASA Technical Reports Server (NTRS)

Bozeman, Richard J., Jr.

1993-01-01

Compact electronic circuit transfers dc power to, and preprocesses ac output of, accelerometer and associated preamplifier. Incorporated into accelerometer case during initial fabrication or retrofit onto commercial accelerometer. Made of commercial integrated circuits and other conventional components; made smaller by use of micrologic and surface-mount technology.

LEC GaAs for integrated circuit applications

NASA Technical Reports Server (NTRS)

Kirkpatrick, C. G.; Chen, R. T.; Homes, D. E.; Asbeck, P. M.; Elliott, K. R.; Fairman, R. D.; Oliver, J. D.

1984-01-01

Recent developments in liquid encapsulated Czochralski techniques for the growth of semiinsulating GaAs for integrated circuit applications have resulted in significant improvements in the quality and quantity of GaAs material suitable for device processing. The emergence of high performance GaAs integrated circuit technologies has accelerated the demand for high quality, large diameter semiinsulating GaAs substrates. The new device technologies, including digital integrated circuits, monolithic microwave integrated circuits and charge coupled devices have largely adopted direct ion implantation for the formation of doped layers. Ion implantation lends itself to good uniformity and reproducibility, high yield and low cost; however, this technique also places stringent demands on the quality of the semiinsulating GaAs substrates. Although significant progress was made in developing a viable planar ion implantation technology, the variability and poor quality of GaAs substrates have hindered progress in process development.

Additive manufacturing of hybrid circuits

DOE PAGES

Bell, Nelson S.; Sarobol, Pylin; Cook, Adam; ...

2016-03-26

There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects.more » Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. As a result, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.« less

Walk-through survey report: Control technology for integrated circuit fabrication, Xerox Corporation, El Segundo, California

NASA Astrophysics Data System (ADS)

Mihlan, G. J.; Ungers, L. J.; Smith, R. K.; Mitchell, R. I.; Jones, J. H.

1983-05-01

A preliminary control technology assessment survey was conducted at the facility which manufactures N-channel metal oxide semiconductor (NMOS) integrated circuits. The facility has industrial hygiene review procedures for evaluating all new and existing process equipment. Employees are trained in safety, use of personal protective equipment, and emergency response. Workers potentially exposed to arsenic are monitored for urinary arsenic levels. The facility should be considered a candidate for detailed study based on the diversity of process operations encountered and the use of state-of-the-art technology and process equipment.

Mesoscopic Vortex–Meissner currents in ring ladders

NASA Astrophysics Data System (ADS)

Haug, Tobias; Amico, Luigi; Dumke, Rainer; Kwek, Leong-Chuan

2018-07-01

Recent experimental progress have revealed Meissner and Vortex phases in low-dimensional ultracold atoms systems. Atomtronic setups can realize ring ladders, while explicitly taking the finite size of the system into account. This enables the engineering of quantized chiral currents and phase slips in between them. We find that the mesoscopic scale modifies the current. Full control of the lattice configuration reveals a reentrant behavior of Vortex and Meissner phases. Our approach allows a feasible diagnostic of the currents’ configuration through time-of-flight measurements.

Career Ladders and Teacher Incentives: The Utah Experiment. Part II: Case Studies. Final Report: Secretary's Discretionary Program Implementation Grant to Develop Teacher Incentive Structures.

ERIC Educational Resources Information Center

Peterson, Ken; Kauchak, Don

This volume, the second of two reports on development of teacher incentive structures, presents case studies of a career ladder design and teacher evaluation experiment in four Utah school districts. Case studies examined relationships among career ladder features, process variables, and career ladder effectiveness, which is defined in terms of…

Benchmarks of a III-V TFET technology platform against the 10-nm CMOS FinFET technology node considering basic arithmetic circuits

NASA Astrophysics Data System (ADS)

Strangio, S.; Palestri, P.; Lanuzza, M.; Esseni, D.; Crupi, F.; Selmi, L.

2017-02-01

In this work, a benchmark for low-power digital applications of a III-V TFET technology platform against a conventional CMOS FinFET technology node is proposed. The analysis focuses on full-adder circuits, which are commonly identified as representative of the digital logic environment. 28T and 24T topologies, implemented in complementary-logic and transmission-gate logic, respectively, are investigated. Transient simulations are performed with a purpose-built test-bench on each single-bit full adder solution. The extracted delays and energy characteristics are post-processed and translated into figures-of-merit for multi-bit ripple-carry-adders. Trends related to the different full-adder implementations (for the same device technology platform) and to the different technology platforms (for the same full-adder topology) are presented and discussed.

Packaging Of Control Circuits In A Robot Arm

NASA Technical Reports Server (NTRS)

Kast, William

1994-01-01

Packaging system houses and connects control circuitry mounted on circuit boards within shoulder, upper section, and lower section of seven-degree-of-freedom robot arm. Has modular design that incorporates surface-mount technology, multilayer circuit boards, large-scale integrated circuits, and multi-layer flat cables between sections for compactness. Three sections of robot arm contain circuit modules in form of stardardized circuit boards. Each module contains two printed-circuit cards, one of each face.

Microwave integrated circuits for space applications

NASA Technical Reports Server (NTRS)

Leonard, Regis F.; Romanofsky, Robert R.

1991-01-01

Monolithic microwave integrated circuits (MMIC), which incorporate all the elements of a microwave circuit on a single semiconductor substrate, offer the potential for drastic reductions in circuit weight and volume and increased reliability, all of which make many new concepts in electronic circuitry for space applications feasible, including phased array antennas. NASA has undertaken an extensive program aimed at development of MMICs for space applications. The first such circuits targeted for development were an extension of work in hybrid (discrete component) technology in support of the Advanced Communication Technology Satellite (ACTS). It focused on power amplifiers, receivers, and switches at ACTS frequencies. More recent work, however, focused on frequencies appropriate for other NASA programs and emphasizes advanced materials in an effort to enhance efficiency, power handling capability, and frequency of operation or noise figure to meet the requirements of space systems.

Dynamics of a Sliding Ladder Leaning against a Wall

ERIC Educational Resources Information Center

Oliveira, J. B.; Simeão Carvalho, P.; Mota, M. F.; Quintas, M. J.

2015-01-01

This study is about the dynamics of a sliding ladder leaning against a vertical wall. The results are understood by considering the motion divided in two parts: (i) for 0 = t = t[subscript s] with one degree of freedom, and (ii) for t > t[subscript s] with two degrees of freedom, where the separation is determined by the instance t[subscript…

In-plant testing of a novel coal cleaning circuit using advanced technologies. Final technical report, September 1, 1995--August 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Honaker, R.Q.; Reed, S.; Mohanty, M.K.

1997-05-01

A circuit comprised of advanced fine coal cleaning technologies was evaluated in an operating preparation plant to determine circuit performance and to compare the performance with current technologies used to treat -16 mesh fine coal. The circuit integrated a Floatex hydrosizer, a Falcon enhanced gravity concentrator and a Jameson flotation cell. A Packed-Column was used to provide additional reductions in the pyritic sulfur and ash contents by treatment of the Floatex-Falcon-Jameson circuit product. For a low sulfur Illinois No. 5 coal, the pyritic sulfur content was reduced from 0.67% to 0.34% at a combustible recovery of 93.2%. The ash contentmore » was decreased from 27.6% to 5.84%, which equates to an organic efficiency of 95% according to gravity-based washability data. The separation performance achieved on a high sulfur Illinois No. 5 coal resulted in the rejection of 72.7% of the pyritic sulfur and 82.3% of the ash-forming material at a recovery of 8 1 %. Subsequent pulverization of the cleaned product and retreatment in a Falcon concentrator and Packed-Column resulted in overall circuit ash and pyritic sulfur rejections of 89% and 93%, respectively, which yielded a pyritic sulfur content reduction from 2.43% to 0.30%. This separation reduced the sulfur dioxide emission rating of an Illinois No. 5 coal from 6.21 to 1.75 lbs SO{sub 2}/MBTU, which is Phase I compliance coal. A comparison of the results obtained from the Floatex-Falcon-Jameson circuit with those of the existing circuit revealed that the novel fine coal circuit provides 10% to 20% improvement in mass yield to the concentrate while rejecting greater amounts of ash and pyritic sulfur.« less

Optical Spectra of the Jaynes-Cummings Ladder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laussy, Fabrice P.; Valle, Elena del

2009-06-29

We explore how the Jaynes-Cummings ladder transpires in the emitted spectra of a two-level system in strong coupling with a single mode of light. We focus on the case of very strong coupling, that would be achieved with systems of exceedingly good quality (very long lifetimes for both the emitter and the cavity). We focus on the incoherent regime of excitation, that is realized with semiconductors quantum dots in microcavities, and discuss how reasonable is the understanding of the systems in terms of transitions between dressed states of the Jaynes-Cummings Hamiltonian.

Low-Field Bi-Skyrmion Formation in a Noncentrosymmetric Chimney Ladder Ferromagnet

NASA Astrophysics Data System (ADS)

Takagi, R.; Yu, X. Z.; White, J. S.; Shibata, K.; Kaneko, Y.; Tatara, G.; Rønnow, H. M.; Tokura, Y.; Seki, S.

2018-01-01

The real-space spin texture and the relevant magnetic parameters were investigated for an easy-axis noncentrosymmetric ferromagnet Cr11 Ge19 with Nowotny chimney ladder structure. Using Lorentz transmission electron microscopy, we report the formation of bi-Skyrmions, i.e., pairs of spin vortices with opposite magnetic helicities. The quantitative evaluation of the magnetocrystalline anisotropy and Dzyaloshinskii-Moriya interaction (DMI) proves that the magnetic dipolar interaction plays a more important role than the DMI on the observed bi-Skyrmion formation. Notably, the critical magnetic field value required for the formation of bi-Skyrmions turned out to be extremely small in this system, which is ascribed to strong easy-axis anisotropy associated with the characteristic helix crystal structure. The family of Nowotny chimney ladder compounds may offer a unique material platform where two distinctive Skyrmion formation mechanisms favoring different topological spin textures can become simultaneously active.

Two-leg ladder systems with dipole–dipole Fermion interactions

NASA Astrophysics Data System (ADS)

Mosadeq, Hamid; Asgari, Reza

2018-05-01

The ground-state phase diagram of a two-leg fermionic dipolar ladder with inter-site interactions is studied using density matrix renormalization group (DMRG) techniques. We use a state-of-the-art implementation of the DMRG algorithm and finite size scaling to simulate large system sizes with high accuracy. We also consider two different model systems and explore stable phases in half and quarter filling factors. We find that in the half filling, the charge and spin gaps emerge in a finite value of the dipole–dipole and on-site interactions. In the quarter filling case, s-wave superconducting state, charge density wave, homogenous insulating and phase separation phases occur depend on the interaction values. Moreover, in the dipole–dipole interaction, the D-Mott phase emerges when the hopping terms along the chain and rung are the same, whereas, this phase has been only proposed for the anisotropic Hubbard model. In the half filling case, on the other hand, there is either charge-density wave or charged Mott order phase depends on the orientation of the dipole moments of the particles with respect to the ladder geometry.

The Missouri Career Development and Teacher Excellence Plan: An Initial Study of Missouri's Career Ladder Program. A Technical Report.

ERIC Educational Resources Information Center

Schofer, Richard C.; And Others

The Missouri Plan provides for direct participation of teachers in the planning, development, and implementation of the district career ladder plan. This study analyzed the appropriateness of the Missouri teacher incentive plan. In particular, the study sought to determine why districts did or did not choose to implement career ladder programs;…

Tank 188A, detail of valves, pipes, and top access ladder ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Tank 188-A, detail of valves, pipes, and top access ladder on east side. Ordnance warehouse A-199 is in the far distance. View to south. - Mare Island Naval Shipyard, Fresh Water Tanks, East of Mesa Road & north of Kieper Road, Vallejo, Solano County, CA

The transport dynamics of chloride and sodium in a ladder fen during a continuous wastewater polishing experiment

NASA Astrophysics Data System (ADS)

McCarter, Colin P. R.; Price, Jonathan S.

2017-06-01

Ladder fen peatlands have excellent potential for wastewater polishing as they naturally contain both open water (pools) and subsurface (peat) treatment landforms; however, there is a poor understanding of solute transport in ladder fens with and without the increased hydrological load imposed by wastewater discharge. To better understand solute transport in ladder fens under wastewater polishing conditions a continuous solute (NaCl) tracer experiment (38 m3 day-1 of water, chloride - 47.2 mg L-1, and sodium - 25.3 mg L-1) was conducted during the summer of 2014 (day of year 192-243) in a small ladder fen in the James Bay Lowland. The transmissivity distribution and effective porosity (average 0.5) of the peat ribs were determined through repeated bail tests and the drainable porosity of 18 peat cores at -100 mb, respectively. Water samples were taken at least every 7 days to capture the solute (sodium and chloride) plumes. Both solute plumes never reached the site outflow (∼250 m downgradient) and displayed complex plume morphology, typically following the patterns of higher hydraulic conductivity within the upper 0.1 m of the saturated peat, rather than the microtopography. Based on the 50% breakthrough isotherms, sodium and chloride were transported at an average solute velocity of 1.9 and 1.1 m day-1, respectively (average linear groundwater velocity = 2.1 m day-1); thus, the solutes were retarded by a factor of 2.1 and 1.2 for sodium and chloride, respectively. Due to the inherent retardation of solutes into inactive pores and relatively high solute residence times, this study demonstrates the potential for wastewater polishing in ladder fens.

Multi-material size optimization of a ladder frame chassis

NASA Astrophysics Data System (ADS)

Baker, Michael

The Corporate Average Fuel Economy (CAFE) is an American fuel standard that sets regulations on fuel economy in vehicles. This law ultimately shapes the development and design research for automakers. Reducing the weight of conventional cars offers a way to improve fuel efficiency. This research investigated the optimality of an automobile's ladder frame chassis (LFC) by conducting multi-objective optimization on the LFC in order to reduce the weight of the chassis. The focus of the design and optimization was a ladder frame chassis commonly used for mass production light motor vehicles with an open-top rear cargo area. This thesis is comprised of two major sections. The first looked to perform thickness optimization in the outer walls of the ladder frame. In the second section, many multi-material distributions, including steel and aluminium varieties, were investigated. A simplified model was used to do an initial hand calculation analysis of the problem. This was used to create a baseline validation to compare the theory with the modeling. A CAD model of the LFC was designed. From the CAD model, a finite element model was extracted and joined using weld and bolt connectors. Following this, a linear static analysis was performed to look at displacement and stresses when subjected to loading conditions that simulate harsh driving conditions. The analysis showed significant values of stress and displacement on the ends of the rails, suggesting improvements could be made elsewhere. An optimization scheme was used to find the values of an all steel frame an optimal thickness distribution was found. This provided a 13% weight reduction over the initial model. To advance the analysis a multi-material approach was used to push the weight savings even further. Several material distributions were analyzed and the lightest utilized aluminium in all but the most strenuous subjected components. This enabled a reduction in weight of 15% over the initial model, equivalent to

Commercialisation of CMOS Integrated Circuit Technology in Multi-Electrode Arrays for Neuroscience and Cell-Based Biosensors

PubMed Central

Graham, Anthony H. D.; Robbins, Jon; Bowen, Chris R.; Taylor, John

2011-01-01

The adaptation of standard integrated circuit (IC) technology as a transducer in cell-based biosensors in drug discovery pharmacology, neural interface systems and electrophysiology requires electrodes that are electrochemically stable, biocompatible and affordable. Unfortunately, the ubiquitous Complementary Metal Oxide Semiconductor (CMOS) IC technology does not meet the first of these requirements. For devices intended only for research, modification of CMOS by post-processing using cleanroom facilities has been achieved. However, to enable adoption of CMOS as a basis for commercial biosensors, the economies of scale of CMOS fabrication must be maintained by using only low-cost post-processing techniques. This review highlights the methodologies employed in cell-based biosensor design where CMOS-based integrated circuits (ICs) form an integral part of the transducer system. Particular emphasis will be placed on the application of multi-electrode arrays for in vitro neuroscience applications. Identifying suitable IC packaging methods presents further significant challenges when considering specific applications. The various challenges and difficulties are reviewed and some potential solutions are presented. PMID:22163884

DETAIL VIEW ON THE MAIN ASSEMBLY LEVEL OF A LADDER ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL VIEW ON THE MAIN ASSEMBLY LEVEL OF A LADDER TO THE CATWALK AT COLUMN LINE AA-28 SHOWING VERTICAL MECHANICAL DUCT, RETURN AIR FLOOR GRILLE, STEEL INDUSTRIAL SASH WINDOWS AND CROSS BRACING OF SOUTH WALL. - Offutt Air Force Base, Glenn L. Martin-Nebraska Bomber Plant, Building D, Peacekeeper Drive, Bellevue, Sarpy County, NE

Real-space localization and quantification of hole distribution in chain-ladder Sr3Ca11Cu24O41 superconductor.

PubMed

Bugnet, Matthieu; Löffler, Stefan; Hawthorn, David; Dabkowska, Hanna A; Luke, Graeme M; Schattschneider, Peter; Sawatzky, George A; Radtke, Guillaume; Botton, Gianluigi A

2016-03-01

Understanding the physical properties of the chain-ladder Sr3Ca11Cu24O41 hole-doped superconductor has been precluded by the unknown hole distribution among chains and ladders. We use electron energy-loss spectrometry (EELS) in a scanning transmission electron microscope (STEM) at atomic resolution to directly separate the contributions of chains and ladders and to unravel the hole distribution from the atomic scale variations of the O-K near-edge structures. The experimental data unambiguously demonstrate that most of the holes lie within the chain layers. A quantitative interpretation supported by inelastic scattering calculations shows that about two holes are located in the ladders, and about four holes in the chains, shedding light on the electronic structure of Sr3Ca11Cu24O41. Combined atomic resolution STEM-EELS and inelastic scattering calculations is demonstrated as a powerful approach toward a quantitative understanding of the electronic structure of cuprate superconductors, offering new possibilities for elucidating their physical properties.

Real-space localization and quantification of hole distribution in chain-ladder Sr3Ca11Cu24O41 superconductor

PubMed Central

Bugnet, Matthieu; Löffler, Stefan; Hawthorn, David; Dabkowska, Hanna A.; Luke, Graeme M.; Schattschneider, Peter; Sawatzky, George A.; Radtke, Guillaume; Botton, Gianluigi A.

2016-01-01

Understanding the physical properties of the chain-ladder Sr3Ca11Cu24O41 hole-doped superconductor has been precluded by the unknown hole distribution among chains and ladders. We use electron energy-loss spectrometry (EELS) in a scanning transmission electron microscope (STEM) at atomic resolution to directly separate the contributions of chains and ladders and to unravel the hole distribution from the atomic scale variations of the O-K near-edge structures. The experimental data unambiguously demonstrate that most of the holes lie within the chain layers. A quantitative interpretation supported by inelastic scattering calculations shows that about two holes are located in the ladders, and about four holes in the chains, shedding light on the electronic structure of Sr3Ca11Cu24O41. Combined atomic resolution STEM-EELS and inelastic scattering calculations is demonstrated as a powerful approach toward a quantitative understanding of the electronic structure of cuprate superconductors, offering new possibilities for elucidating their physical properties. PMID:27051872

Effect of sieving polymer concentration on separation of 100 bp DNA Ladder by capillary gel electrophoresis

NASA Astrophysics Data System (ADS)

Nakazumi, T.; Hara, Y.

2017-09-01

We studied the effect of sieving polymer concentration on separation of a 100 bp DNA Ladder by capillary gel electrophoresis (CGE) using hydroxyethyl cellulose (HEC) with a molecular size of 1000 k. For measurement purposes, we selected a fused silica capillary with total length of 15 cm and effective length of 7.5 cm; this was applied to compact CGE equipment for a Point-Care-Testing (POCT) system. Measurement results of the 100 bp DNA Ladder sample indicated that small DNA separation was significantly affected by HEC sieving polymer concentration. This was due to the level of entanglement between small DNA molecules and the sieving polymer chain significantly influencing migration time, mobility, and resolution length of the CGE process. We concluded that 1.0 w/v % HEC sieving polymer concentration was optimal for CGE separation of DNA ≥1000bp in the 100 bp DNA Ladder (100-1500 bp) when using the short-length capillary.

Silicon Carbide Integrated Circuit Chip

NASA Image and Video Library

2015-02-17

A multilevel interconnect silicon carbide integrated circuit chip with co-fired ceramic package and circuit board recently developed at the NASA GRC Smart Sensors and Electronics Systems Branch for high temperature applications. High temperature silicon carbide electronics and compatible packaging technologies are elements of instrumentation for aerospace engine control and long term inner-solar planet explorations.

SUSY’s Ladder: Reframing sequestering at Large Volume

DOE PAGES

Reece, Matthew; Xue, Wei

2016-04-07

Theories with approximate no-scale structure, such as the Large Volume Scenario, have a distinctive hierarchy of multiple mass scales in between TeV gaugino masses and the Planck scale, which we call SUSY's Ladder. This is a particular realization of Split Supersymmetry in which the same small parameter suppresses gaugino masses relative to scalar soft masses, scalar soft masses relative to the gravitino mass, and the UV cutoff or string scale relative to the Planck scale. This scenario has many phenomenologically interesting properties, and can avoid dangers including the gravitino problem, flavor problems, and the moduli-induced LSP problem that plague othermore » supersymmetric theories. We study SUSY's Ladder using a superspace formalism that makes the mysterious cancelations in previous computations manifest. This opens the possibility of a consistent effective field theory understanding of the phenomenology of these scenarios, based on power-counting in the small ratio of string to Planck scales. We also show that four-dimensional theories with approximate no-scale structure enforced by a single volume modulus arise only from two special higher-dimensional theories: five-dimensional supergravity and ten-dimensional type IIB supergravity. As a result, this gives a phenomenological argument in favor of ten dimensional ultraviolet physics which is different from standard arguments based on the consistency of superstring theory.« less

Evaluation Practice and Theory: Up and down the Ladder of Abstraction

ERIC Educational Resources Information Center

Leviton, Laura C.

2015-01-01

Debra Rog presented the 2014 Eleanor Chelimsky Forum address, offering ways to integrate evaluation theory and practice by abundant use of practice examples. These examples illustrate the effective use of the Ladder of Abstraction from semantics, working from the concrete to the abstract and back again.

Parents' Participation on School Councils Analysed through Arnstein's Ladder of Participation

ERIC Educational Resources Information Center

Stelmach, Bonnie

2016-01-01

Although parent school councils are the archetypal arrangement for engaging parents in school improvement planning, their effectiveness is negligible when it comes to building parents' capacity for and confidence in educational decision-making. Using Arnstein's ladder of citizen participation, this qualitative case study investigated the nature…

Dental Laboratory Career Ladder (AFSC 4Y1X1)

DTIC Science & Technology

1994-08-01

analysis identified one job cluster and seven jobs: Base Dental Lab cluster, Orthodontic Appliance Fabricator job, Fixed Restoration Fabricator job, Crown...reline and repair, removable partial denture construction, crown and fixed partial denture construction, fabrication of orthodontic appliances, and...specialized prostheses. Preventive maintenance and safety precautions for dental laboratory equipment are also stressed . Entry into the career ladder

Implementation of a pharmacist career ladder program.

PubMed

Heavner, Mojdeh S; Tichy, Eric M; Yazdi, Marina

2016-10-01

The implementation and outcomes of a pharmacist career ladder program (PCLP) at a tertiary care, academic medical center are described. A PCLP was developed at Yale-New Haven Hospital to guide career development, motivate staff to perform beyond their daily tasks and responsibilities, and recognize and retain high performers through professional advancement. The PCLP advancement criteria include specific requirements for excellence in five categories: level of training and experience, pharmacy practice, drug information, education and scholarship, and leadership. The PCLP is designed with four distinct tiers: clinical pharmacist, clinical pharmacist II, clinical pharmacy specialist, and clinical pharmacy specialist II. The specific criteria are increasingly challenging to achieve when moving up the ladder. Pharmacists may apply voluntarily each year for advancement. A PCLP review committee consisting of pharmacist peers and managers meets annually to discuss and vote on career advancement decisions. Since PCLP implementation, we have observed an increasing success rate for advancement (50% in 2013, 85% in 2014, and 100% in 2015) and a considerable increase in pharmacist participation in clinical and process improvement projects, as well as intervention and medication-use variance documentation. The implementation of a PCLP at a tertiary care, academic medical center provided an opportunity for frontline pharmacists to advance professionally and increased their participation and leadership in clinical and process improvement projects and drug-use policy and medication safety initiatives; the program also increased the number of pharmacists with specialty board certification and peer-reviewed publications. Copyright © 2016 by the American Society of Health-System Pharmacists, Inc. All rights reserved.

Illuminating Neural Circuits: From Molecules to MRI.

PubMed

Lee, Jin Hyung; Kreitzer, Anatol C; Singer, Annabelle C; Schiff, Nicholas D

2017-11-08

Neurological disease drives symptoms through pathological changes to circuit functions. Therefore, understanding circuit mechanisms that drive behavioral dysfunction is of critical importance for quantitative diagnosis and systematic treatment of neurological disease. Here, we describe key technologies that enable measurement and manipulation of neural activity and neural circuits. Applying these approaches led to the discovery of circuit mechanisms underlying pathological motor behavior, arousal regulation, and protein accumulation. Finally, we discuss how optogenetic functional magnetic resonance imaging reveals global scale circuit mechanisms, and how circuit manipulations could lead to new treatments of neurological diseases. Copyright © 2017 the authors 0270-6474/17/3710817-09$15.00/0.

Electronic circuits: A compilation. [for electronic equipment in telecommunication

NASA Technical Reports Server (NTRS)

1976-01-01

A compilation containing articles on newly developed electronic circuits and systems is presented. It is divided into two sections: (1) section 1 on circuits and techniques of particular interest in communications technology, and (2) section 2 on circuits designed for a variety of specific applications. The latest patent information available is also given. Circuit diagrams are shown.

Stimulated Raman adiabatic passage in a three-level superconducting circuit

PubMed Central

Kumar, K. S.; Vepsäläinen, A.; Danilin, S.; Paraoanu, G. S.

2016-01-01

The adiabatic manipulation of quantum states is a powerful technique that opened up new directions in quantum engineering—enabling tests of fundamental concepts such as geometrical phases and topological transitions, and holding the promise of alternative models of quantum computation. Here we benchmark the stimulated Raman adiabatic passage for circuit quantum electrodynamics by employing the first three levels of a transmon qubit. In this ladder configuration, we demonstrate a population transfer efficiency >80% between the ground state and the second excited state using two adiabatic Gaussian-shaped control microwave pulses. By doing quantum tomography at successive moments during the Raman pulses, we investigate the transfer of the population in time domain. Furthermore, we show that this protocol can be reversed by applying a third adiabatic pulse, we study a hybrid nondiabatic–adiabatic sequence, and we present experimental results for a quasi-degenerate intermediate level. PMID:26902454

Stimulated Raman adiabatic passage in a three-level superconducting circuit.

PubMed

Kumar, K S; Vepsäläinen, A; Danilin, S; Paraoanu, G S

2016-02-23

The adiabatic manipulation of quantum states is a powerful technique that opened up new directions in quantum engineering--enabling tests of fundamental concepts such as geometrical phases and topological transitions, and holding the promise of alternative models of quantum computation. Here we benchmark the stimulated Raman adiabatic passage for circuit quantum electrodynamics by employing the first three levels of a transmon qubit. In this ladder configuration, we demonstrate a population transfer efficiency >80% between the ground state and the second excited state using two adiabatic Gaussian-shaped control microwave pulses. By doing quantum tomography at successive moments during the Raman pulses, we investigate the transfer of the population in time domain. Furthermore, we show that this protocol can be reversed by applying a third adiabatic pulse, we study a hybrid nondiabatic-adiabatic sequence, and we present experimental results for a quasi-degenerate intermediate level.

Career Ladders and the Professionalization of Teaching: Down the Up Staircase.

ERIC Educational Resources Information Center

Dunwell, Robert R.

School systems interested in improving teacher performance, effectiveness, and job satisfaction while reducing turnover rates might do better to seek ways to enhance the intrinsic rewards of teaching rather than implement such extrinsic motivators as merit pay plans and career ladders. A review of the research literature brings several important…

Graphene radio frequency receiver integrated circuit.

PubMed

Han, Shu-Jen; Garcia, Alberto Valdes; Oida, Satoshi; Jenkins, Keith A; Haensch, Wilfried

2014-01-01

Graphene has attracted much interest as a future channel material in radio frequency electronics because of its superior electrical properties. Fabrication of a graphene integrated circuit without significantly degrading transistor performance has proven to be challenging, posing one of the major bottlenecks to compete with existing technologies. Here we present a fabrication method fully preserving graphene transistor quality, demonstrated with the implementation of a high-performance three-stage graphene integrated circuit. The circuit operates as a radio frequency receiver performing signal amplification, filtering and downconversion mixing. All circuit components are integrated into 0.6 mm(2) area and fabricated on 200 mm silicon wafers, showing the unprecedented graphene circuit complexity and silicon complementary metal-oxide-semiconductor process compatibility. The demonstrated circuit performance allow us to use graphene integrated circuit to perform practical wireless communication functions, receiving and restoring digital text transmitted on a 4.3-GHz carrier signal.

Graphene radio frequency receiver integrated circuit

NASA Astrophysics Data System (ADS)

Han, Shu-Jen; Garcia, Alberto Valdes; Oida, Satoshi; Jenkins, Keith A.; Haensch, Wilfried

2014-01-01

Graphene has attracted much interest as a future channel material in radio frequency electronics because of its superior electrical properties. Fabrication of a graphene integrated circuit without significantly degrading transistor performance has proven to be challenging, posing one of the major bottlenecks to compete with existing technologies. Here we present a fabrication method fully preserving graphene transistor quality, demonstrated with the implementation of a high-performance three-stage graphene integrated circuit. The circuit operates as a radio frequency receiver performing signal amplification, filtering and downconversion mixing. All circuit components are integrated into 0.6 mm2 area and fabricated on 200 mm silicon wafers, showing the unprecedented graphene circuit complexity and silicon complementary metal-oxide-semiconductor process compatibility. The demonstrated circuit performance allow us to use graphene integrated circuit to perform practical wireless communication functions, receiving and restoring digital text transmitted on a 4.3-GHz carrier signal.

Review of CMOS Integrated Circuit Technologies for High-Speed Photo-Detection

PubMed Central

Jeong, Gyu-Seob

2017-01-01

The bandwidth requirement of wireline communications has increased exponentially because of the ever-increasing demand for data centers and high-performance computing systems. However, it becomes difficult to satisfy the requirement with legacy electrical links which suffer from frequency-dependent losses due to skin effects, dielectric losses, channel reflections, and crosstalk, resulting in a severe bandwidth limitation. In order to overcome this challenge, it is necessary to introduce optical communication technology, which has been mainly used for long-reach communications, such as long-haul networks and metropolitan area networks, to the medium- and short-reach communication systems. However, there still remain important issues to be resolved to facilitate the adoption of the optical technologies. The most critical challenges are the energy efficiency and the cost competitiveness as compared to the legacy copper-based electrical communications. One possible solution is silicon photonics which has long been investigated by a number of research groups. Despite inherent incompatibility of silicon with the photonic world, silicon photonics is promising and is the only solution that can leverage the mature complementary metal-oxide-semiconductor (CMOS) technologies. Silicon photonics can be utilized in not only wireline communications but also countless sensor applications. This paper introduces a brief review of silicon photonics first and subsequently describes the history, overview, and categorization of the CMOS IC technology for high-speed photo-detection without enumerating the complex circuital expressions and terminologies. PMID:28841154

Review of CMOS Integrated Circuit Technologies for High-Speed Photo-Detection.

PubMed

Jeong, Gyu-Seob; Bae, Woorham; Jeong, Deog-Kyoon

2017-08-25

The bandwidth requirement of wireline communications has increased exponentially because of the ever-increasing demand for data centers and high-performance computing systems. However, it becomes difficult to satisfy the requirement with legacy electrical links which suffer from frequency-dependent losses due to skin effects, dielectric losses, channel reflections, and crosstalk, resulting in a severe bandwidth limitation. In order to overcome this challenge, it is necessary to introduce optical communication technology, which has been mainly used for long-reach communications, such as long-haul networks and metropolitan area networks, to the medium- and short-reach communication systems. However, there still remain important issues to be resolved to facilitate the adoption of the optical technologies. The most critical challenges are the energy efficiency and the cost competitiveness as compared to the legacy copper-based electrical communications. One possible solution is silicon photonics which has long been investigated by a number of research groups. Despite inherent incompatibility of silicon with the photonic world, silicon photonics is promising and is the only solution that can leverage the mature complementary metal-oxide-semiconductor (CMOS) technologies. Silicon photonics can be utilized in not only wireline communications but also countless sensor applications. This paper introduces a brief review of silicon photonics first and subsequently describes the history, overview, and categorization of the CMOS IC technology for high-speed photo-detection without enumerating the complex circuital expressions and terminologies.

16. View, looking west, of fish ladder and steel frame ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

16. View, looking west, of fish ladder and steel frame supporting fish trap, both constructed by U.S. Army Corps of Engineers, 1949. One-story wood-frame building with hip roof is a utility shed used for fish-trap operation. Photo by Jet Lowe, HAER, 1989. - Puget Sound Power & Light Company, White River Hydroelectric Project, 600 North River Avenue, Dieringer, Pierce County, WA

Astronaut Alan Bean steps from ladder of Lunar Module for EVA

NASA Technical Reports Server (NTRS)

1969-01-01

Astronaut Alan L. Bean, lunar module pilot for the Apollo 12 lunar landing mission, steps from the ladder of the Lunar Module to join Astronaut Charles Conrad Jr., commander, in extravehicular activity on November 19, 1969. Astronaut Ricard F. Gordon Jr., command module pilot, remained with the Command/Service Modules in lunar orbit.

Process design kit and circuits at a 2 µm technology node for flexible wearable electronics applications (Conference Presentation)

NASA Astrophysics Data System (ADS)

Torres-Miranda, Miguel; Petritz, Andreas; Gold, Herbert; Stadlober, Barbara

2016-09-01

In this work we present our most advanced technology node of organic thin film transistors (OTFTs) manufactured with a channel length as short as 2 μm by contact photolithography and a self-alignment process directly on a plastic substrate. Our process design kit (PDK) is described with P-type transistors, capacitors and 3 metal layers for connections of complex circuits. The OTFTs are composed of a double dielectric layer with a photopatternable ultra thin polymer (PNDPE) and alumina, with a thickness on the order of 100 nm. The organic semiconductor is either Pentacene or DNTT, which have a stable average mobility up to 0.1 cm2/Vs. Finally, a polymer (e.g.: Parylene-C) is used as a passivation layer. We describe also our design rules for the placement of standard circuit cells. A "plastic wafer" is fabricated containing 49 dies. Each die of 1 cm2 has between 25 to 50 devices, proving larger scale integration in such a small space, unique in organic technologies. Finally, we present the design (by simulations using a Spice model for OTFTs) and the test of analog and digital basic circuits: amplifiers with DC gains of about 20 dB, comparators, inverters and logic gates working in the frequency range of 1-10 kHz. These standard circuit cells could be used for signal conditioning and integrated as active matrices for flexible sensors from 3rd party institutions, thus opening our fab to new ideas and sophisticated pre-industrial low cost applications for the emerging fields of biomedical devices and wearable electronics for virtual/augmented reality.

Frustrated quantum magnetism in the Kondo lattice on the zigzag ladder

NASA Astrophysics Data System (ADS)

Peschke, Matthias; Rausch, Roman; Potthoff, Michael

2018-03-01

The interplay between the Kondo effect, indirect magnetic interaction, and geometrical frustration is studied in the Kondo lattice on the one-dimensional zigzag ladder. Using the density-matrix renormalization group, the ground-state and various short- and long-range spin- and density-correlation functions are calculated for the model at half filling as a function of the antiferromagnetic Kondo interaction down to J =0.3 t , where t is the nearest-neighbor hopping on the zigzag ladder. Geometrical frustration is shown to lead to at least two critical points: Starting from the strong-J limit, where almost local Kondo screening dominates and where the system is a nonmagnetic Kondo insulator, antiferromagnetic correlations between nearest-neighbor and next-nearest-neighbor local spins become stronger and stronger, until at Jcdim≈0.89 t frustration is alleviated by a spontaneous breaking of translational symmetry and a corresponding transition to a dimerized state. This is characterized by antiferromagnetic correlations along the legs and by alternating antiferro- and ferromagnetic correlations on the rungs of the ladder. A mechanism of partial Kondo screening that has been suggested for the Kondo lattice on the two-dimensional triangular lattice is not realized in the one-dimensional case. Furthermore, within the symmetry-broken dimerized state, there is a magnetic transition to a 90∘ quantum spin spiral with quasi-long-range order at Jcmag≈0.84 t . The quantum-critical point is characterized by a closure of the spin gap (with decreasing J ) and a divergence of the spin-correlation length and of the spin-structure factor S (q ) at wave vector q =π /2 . This is opposed to the model on the one-dimensional bipartite chain, which is known to have a finite spin gap for all J >0 at half filling.

A Demonstration of Helping Adolescents with Mild Intellectual Disability Climb Ladders

ERIC Educational Resources Information Center

Chan, Kok Hoe Anthony; Varahan, Jayashree Lakshmi; Loh, Peng Loong Daniel; Tan, Sey Ing

2011-01-01

A research team at a vocational school in Singapore, catering mainly to students between the ages of 17-21 with mild intellectual disability, studied how to best address the challenge of enabling students to learn how to climb ladders (a skill necessary at many job placements). They documented the approach used and suggested extrapolations and…

Optimal temperature ladders in replica exchange simulations

NASA Astrophysics Data System (ADS)

Denschlag, Robert; Lingenheil, Martin; Tavan, Paul

2009-04-01

In replica exchange simulations, a temperature ladder with N rungs spans a given temperature interval. Considering systems with heat capacities independent of the temperature, here we address the question of how large N should be chosen for an optimally fast diffusion of the replicas through the temperature space. Using a simple example we show that choosing average acceptance probabilities of about 45% and computing N accordingly maximizes the round trip rates r across the given temperature range. This result differs from previous analyses which suggested smaller average acceptance probabilities of about 23%. We show that the latter choice maximizes the ratio r/N instead of r.

Clarifying the Hubble constant tension with a Bayesian hierarchical model of the local distance ladder

NASA Astrophysics Data System (ADS)

Feeney, Stephen M.; Mortlock, Daniel J.; Dalmasso, Niccolò

2018-05-01

Estimates of the Hubble constant, H0, from the local distance ladder and from the cosmic microwave background (CMB) are discrepant at the ˜3σ level, indicating a potential issue with the standard Λ cold dark matter (ΛCDM) cosmology. A probabilistic (i.e. Bayesian) interpretation of this tension requires a model comparison calculation, which in turn depends strongly on the tails of the H0 likelihoods. Evaluating the tails of the local H0 likelihood requires the use of non-Gaussian distributions to faithfully represent anchor likelihoods and outliers, and simultaneous fitting of the complete distance-ladder data set to ensure correct uncertainty propagation. We have hence developed a Bayesian hierarchical model of the full distance ladder that does not rely on Gaussian distributions and allows outliers to be modelled without arbitrary data cuts. Marginalizing over the full ˜3000-parameter joint posterior distribution, we find H0 = (72.72 ± 1.67) km s-1 Mpc-1 when applied to the outlier-cleaned Riess et al. data, and (73.15 ± 1.78) km s-1 Mpc-1 with supernova outliers reintroduced (the pre-cut Cepheid data set is not available). Using our precise evaluation of the tails of the H0 likelihood, we apply Bayesian model comparison to assess the evidence for deviation from ΛCDM given the distance-ladder and CMB data. The odds against ΛCDM are at worst ˜10:1 when considering the Planck 2015 XIII data, regardless of outlier treatment, considerably less dramatic than naïvely implied by the 2.8σ discrepancy. These odds become ˜60:1 when an approximation to the more-discrepant Planck Intermediate XLVI likelihood is included.

Utah Teacher Evaluation Project: The Park City Career Ladder Design. Final Report: Secretary's Discretionary Program, Planning Grant to Develop Teacher Incentive Programs.

ERIC Educational Resources Information Center

Peterson, Ken; And Others

The Park City School District (Utah) career ladder design provides a system in which teachers are positioned and paid according to successful performance and differentiation of responsibilities. It includes an evaluation system to differentiate among teachers. The career ladder design presents a number of innovations; for example, excellent…

Engineering Synthetic Gene Circuits in Living Cells with CRISPR Technology.

PubMed

Jusiak, Barbara; Cleto, Sara; Perez-Piñera, Pablo; Lu, Timothy K

2016-07-01

One of the goals of synthetic biology is to build regulatory circuits that control cell behavior, for both basic research purposes and biomedical applications. The ability to build transcriptional regulatory devices depends on the availability of programmable, sequence-specific, and effective synthetic transcription factors (TFs). The prokaryotic clustered regularly interspaced short palindromic repeat (CRISPR) system, recently harnessed for transcriptional regulation in various heterologous host cells, offers unprecedented ease in designing synthetic TFs. We review how CRISPR can be used to build synthetic gene circuits and discuss recent advances in CRISPR-mediated gene regulation that offer the potential to build increasingly complex, programmable, and efficient gene circuits in the future. Copyright © 2016. Published by Elsevier Ltd.

Electron spin resonance modes in a strong-leg ladder in the Tomonaga-Luttinger liquid phase

NASA Astrophysics Data System (ADS)

Ozerov, M.; Maksymenko, M.; Wosnitza, J.; Honecker, A.; Landee, C. P.; Turnbull, M. M.; Furuya, S. C.; Giamarchi, T.; Zvyagin, S. A.

2015-12-01

Magnetic excitations in the strong-leg quantum spin ladder compound (C7H10N) 2CuBr4 (known as DIMPY) in the field-induced Tomonaga-Luttinger spin-liquid phase are studied by means of high-field electron spin resonance (ESR) spectroscopy. The presence of a gapped ESR mode with unusual nonlinear frequency-field dependence is revealed experimentally. Using a combination of analytic and exact-diagonalization methods, we compute the dynamical structure factor and identify this mode with longitudinal excitations in the antisymmetric channel. We argue that these excitations constitute a fingerprint of the spin dynamics in a strong-leg spin-1/2 Heisenberg antiferromagnetic ladder and owe their ESR observability to the uniform Dzyaloshinskii-Moriya interaction.

Developing 300°C Ceramic Circuit Boards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Normann, Randy A

2015-02-15

This paper covers the development of a geothermal ceramic circuit board technology using 3D traces in a machinable ceramic. Test results showing the circuit board to be operational to at least 550°C. Discussion on producing this type of board is outlined along with areas needing improvement.

[Ladder step strategy for surgical repair of congenital concealed penis in children].

PubMed

Wang, Fu-Ran; Zhong, Hong-Ji; Chen, Yi; Zhao, Jun-Feng; Li, Yan

2016-11-01

To assess the feasibility of the ladder step strategy in surgical repair of congenital concealed penis in children. This study included 52 children with congenital concealed penis treated in the past two years by surgical repair using the ladder step strategy, which consists of five main steps: cutting the narrow ring of the foreskin, degloving the penile skin, fixing the penile skin at the base, covering the penile shaft, and reshaping the prepuce. The perioperative data of the patients were prospectively collected and statistically described. Of the 52 patients, 20 needed remodeling of the frenulum and 27 received longitudinal incision in the penoscrotal junction to expose and deglove the penile shaft. The advanced scrotal flap technique was applied in 8 children to cover the penile shaft without tension, the pedicled foreskin flap technique employed in 11 to repair the penile skin defect, and excision of the webbed skin of the ventral penis performed in another 44 to remodel the penoscrotal angle. The operation time, blood loss, and postoperative hospital stay were 40－100 minutes, 5－30 ml, and 3－6 days, respectively. Wound bleeding and infection occurred in 1 and 5 cases, respectively. Follow-up examinations at 3 and 6 months after surgery showed that all the children had a satisfactory penile appearance except for some minor complications (2 cases of penile retraction, 2 cases of redundant ventral skin, and 1 case of iatrogenic penile curvature). The ladder step strategy for surgical repair of congenital concealed penis in children is a simple procedure with minor injury and satisfactory appearance of the penis.

Automatic recloser circuit breaker integrated with GSM technology for power system notification

NASA Astrophysics Data System (ADS)

Lada, M. Y.; Khiar, M. S. A.; Ghani, S. A.; Nawawi, M. R. M.; Rahim, N. H.; Sinar, L. O. M.

2015-05-01

Lightning is one type of transient faults that usually cause the circuit breaker in the distribution board trip due to overload current detection. The instant tripping condition in the circuit breakers clears the fault in the system. Unfortunately most circuit breakers system is manually operated. The power line will be effectively re-energized after the clearing fault process is finished. Auto-reclose circuit is used on the transmission line to carry out the duty of supplying quality electrical power to customers. In this project, an automatic reclose circuit breaker for low voltage usage is designed. The product description is the Auto Reclose Circuit Breaker (ARCB) will trip if the current sensor detects high current which exceeds the rated current for the miniature circuit breaker (MCB) used. Then the fault condition will be cleared automatically and return the power line to normal condition. The Global System for Mobile Communication (GSM) system will send SMS to the person in charge if the tripping occurs. If the over current occurs in three times, the system will fully trip (open circuit) and at the same time will send an SMS to the person in charge. In this project a 1 A is set as the rated current and any current exceeding a 1 A will cause the system to trip or interrupted. This system also provides an additional notification for user such as the emergency light and warning system.

Spin rotational symmetry breaking by orbital current patterns in two-leg Cu-O Hubbard ladders

NASA Astrophysics Data System (ADS)

Chudzinski, Piotr; Gabay, Marc; Giamarchi, Thierry

2010-03-01

In the weak-coupling limit, we study, as a function of doping, two-leg ladders with a unit cell containing both Cu and O atoms. For purely repulsive interactions, using bosonization and a novel RG scheme, we find that in a broad region of the phase diagram, the ground state consists of a pattern of orbital currents (OCP) defined on the top of an incommensurate density wave. The internal symmetry of the OCP is specific for the ladder structure, different than the ones suggested up to now for 2D cuprates. We focus on this OCP and look for measurable signals of its existence: we compute magnetic fields induced within the ladder and we check what kind of changes in the phase diagram one may expect due to SU(2) spin-rotational symmetry breaking. We also investigate a single impurity problem (incl. OCP): we discuss if Kondo physics is at play, and make qualitative predictions about the nature of impurity backscattering. This enables us to show the influence of SU(2) symmetry breaking on conductivity. We estimate the value of gap opened due to the OCP, give analytic expressions for correlation functions and discuss magnetic properties of a new phase.

Carbon nanotube circuit integration up to sub-20 nm channel lengths.

PubMed

Shulaker, Max Marcel; Van Rethy, Jelle; Wu, Tony F; Liyanage, Luckshitha Suriyasena; Wei, Hai; Li, Zuanyi; Pop, Eric; Gielen, Georges; Wong, H-S Philip; Mitra, Subhasish

2014-04-22

Carbon nanotube (CNT) field-effect transistors (CNFETs) are a promising emerging technology projected to achieve over an order of magnitude improvement in energy-delay product, a metric of performance and energy efficiency, compared to silicon-based circuits. However, due to substantial imperfections inherent with CNTs, the promise of CNFETs has yet to be fully realized. Techniques to overcome these imperfections have yielded promising results, but thus far only at large technology nodes (1 μm device size). Here we demonstrate the first very large scale integration (VLSI)-compatible approach to realizing CNFET digital circuits at highly scaled technology nodes, with devices ranging from 90 nm to sub-20 nm channel lengths. We demonstrate inverters functioning at 1 MHz and a fully integrated CNFET infrared light sensor and interface circuit at 32 nm channel length. This demonstrates the feasibility of realizing more complex CNFET circuits at highly scaled technology nodes.

Digital circuits for computer applications: A compilation

NASA Technical Reports Server (NTRS)

1972-01-01

The innovations in this updated series of compilations dealing with electronic technology represent a carefully selected collection of digital circuits which have direct application in computer oriented systems. In general, the circuits have been selected as representative items of each section and have been included on their merits of having universal applications in digital computers and digital data processing systems. As such, they should have wide appeal to the professional engineer and scientist who encounter the fundamentals of digital techniques in their daily activities. The circuits are grouped as digital logic circuits, analog to digital converters, and counters and shift registers.

Magnetic phase diagram of a frustrated spin ladder

NASA Astrophysics Data System (ADS)

Sugimoto, Takanori; Mori, Michiyasu; Tohyama, Takami; Maekawa, Sadamichi

2018-04-01

Frustrated spin ladders show magnetization plateaux depending on the rung-exchange interaction and frustration defined by the ratio of first and second neighbor exchange interactions in each chain. This paper reports on its magnetic phase diagram. Using the variational matrix-product state method, we accurately determine phase boundaries. Several kinds of magnetization plateaux are induced by the frustration and the strong correlation among quasiparticles on a lattice. The appropriate description of quasiparticles and their relevant interactions are changed by a magnetic field. We find that the frustration differentiates the triplet quasiparticle from the singlet one in kinetic energy.

Astronaut Alan Bean steps from ladder of Lunar Module for EVA

NASA Image and Video Library

1969-11-19

AS12-46-6729 (19 Nov. 1969) --- Astronaut Alan L. Bean, lunar module pilot for the Apollo 12 lunar landing mission, steps from the ladder of the Lunar Module to join astronaut Charles Conrad Jr., commander, in extravehicular activity on Nov. 19, 1969. Astronaut Richard F. Gordon Jr., command module pilot, remained with the Command and Service Modules in lunar orbit.

Development of High Interruption Capability Vacuum Circuit Breaker -Technology of Vacuum Arc Control-

NASA Astrophysics Data System (ADS)

Niwa, Yoshimitsu; Kaneko, Eiji

Vacuum circuit breakers (VCB) have been widely used for power distribution systems. Vacuum Interrupters, which are the current interruption unit, have been increased its interruption capability with the development of vacuum arc control technology by magnetic field. There are three major type electrodes: disk shaped electrodes, radial magnetic field electrodes, axial magnetic field (AMF) electrodes. In the disk shaped electrode, the vacuum arc between the electrodes is not controlled. In the AMF electrode, the vacuum arc is diffused and stabilized by an axial magnetic field, which is parallel to the arc current. In the last type of electrodes, the vacuum arc column is rotated by magnetic force generated by the current flowing in the electrodes. The interruption current and the voltage of one break VCB is increased to 100 kA, 144 kV respectively. This paper describes basic configurations and functions of VCB, vacuum arc control technology in vacuum interrupters, recent researches and applications of VCB.

Context View from 11' on ladder from southeast corner of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Context View from 11' on ladder from southeast corner of Bottle Village parcel, just inside fence. Doll Head Shrine at far left frame, Living Trailer (c.1960 "Spartanette") in center frame. Little Wishing Well at far right frame. Some shrines and small buildings were destroyed in the January 1994 Northridge earthquake, and only their perimeter walls and foundations exist. Camera facing north northwest. - Grandma Prisbrey's Bottle Village, 4595 Cochran Street, Simi Valley, Ventura County, CA

"Printed-circuit" rectenna

NASA Technical Reports Server (NTRS)

Dickinson, R. M.

1977-01-01

Rectifying antenna is less bulky structure for absorbing transmitted microwave power and converting it into electrical current. Printed-circuit approach, using microstrip technology and circularly polarized antenna, makes polarization orientation unimportant and allows much smaller arrays for given performance. Innovation is particularly useful with proposed electric vehicles powered by beam microwaves.

Fundamentals handbook of electrical and computer engineering. Volume 1 Circuits fields and electronics

NASA Astrophysics Data System (ADS)

Chang, S. S. L.

State of the art technology in circuits, fields, and electronics is discussed. The principles and applications of these technologies to industry, digital processing, microwave semiconductors, and computer-aided design are explained. Important concepts and methodologies in mathematics and physics are reviewed, and basic engineering sciences and associated design methods are dealt with, including: circuit theory and the design of magnetic circuits and active filter synthesis; digital signal processing, including FIR and IIR digital filter design; transmission lines, electromagnetic wave propagation and surface acoustic wave devices. Also considered are: electronics technologies, including power electronics, microwave semiconductors, GaAs devices, and magnetic bubble memories; digital circuits and logic design.

Phase transitions and magnetization of the mixed-spin Ising–Heisenberg double sawtooth frustrated ladder

NASA Astrophysics Data System (ADS)

Arian Zad, Hamid; Ananikian, Nerses

2018-04-01

The mixed spin-(1,1/2) Ising–Heisenberg double sawtooth ladder containing a mixture of both spin-1 and spin-1/2 nodal atoms, and the spin-1/2 interstitial dimers are approximately solved by the transfer-matrix method. Here, we study in detail the ground-state phase diagrams, also influences of the bilinear exchange coupling on the rungs and cyclic four-spin exchange interaction in square plaquette of each block on the magnetization and magnetic susceptibility of the suggested ladder at low temperature. Such a double sawtooth ladder may be found in a Shastry-Sutherland lattice-type. In spite of the spin ordering of odd and even blocks being different from each other, due to the commutation relation between all different block Hamiltonians, phase diagrams, magnetization behavior and thermodynamic properties of the model are the same for odd and even blocks. We show that at low temperature, both exchange couplings can change the quality and quantity of the magnetization plateaus versus the magnetic field changes. Specially, we find a new magnetization plateau M/Ms= 5/6 for this model. Besides, we examine the magnetic susceptibility and specific heat of the model in detail. It is proven that behaviors of the magnetization and the magnetic susceptibility coincide at low temperature. The specific heat displays diverse temperature dependencies, which include a Schottky-type peak at a special temperature interval. We observe that with increase of the bilinear exchange coupling on the rungs, second peak temperature dependence grows.

Teacher Bonuses for Extra Work: A Profile of Missouri's Career Ladder Program

ERIC Educational Resources Information Center

Silman, Timothy; Glazerman, Steven

2009-01-01

This report set out to profile the Missouri Career Ladder program by delving beneath the surface and comparing how the program works in practice (based on stakeholder accounts) with how it works in theory (based on published statutes and regulations). The authors found that in many respects the program operates as one might expect. Districts…

Non-local electron transport through normal and topological ladder-like atomic systems

NASA Astrophysics Data System (ADS)

Kurzyna, Marcin; Kwapiński, Tomasz

2018-05-01

We propose a locally protected ladder-like atomic system (nanoconductor) on a substrate that is insensitive to external perturbations. The system corresponds to coupled atomic chains fabricated on different surfaces. Electron transport properties of such conductors are studied theoretically using the model tight-binding Su-Schriffer-Hegger (SSH) Hamiltonian and Green's function formalism. We have found that the conductance of the system is almost insensitive to single adatoms and oscillates as a function of the side chain length with very large periods. Non-local character of the electron transport was observed also for topological SSH chains where nontrivial end states survive in the presence of disturbances as well as for different substrates. We have found that the careful inspection of the density of states or charge waves can provide the information about the atom energy levels and hopping amplitudes. Moreover, the ladder-like geometry allows one to distinguish between normal and topological zero-energy states. It is important that topological chains do not reveal Friedel oscillations which are observed in non-topological chains.

Corrosion Control Specialist Career Ladder AFSC 53530, 53550, 53570, and 53690

DTIC Science & Technology

1975-03-01

AD-AO08 189 CORROSION CONTROL SPECIALIST CAREER LADDER AFSC 53530, 53550, 53570, AND 53690 Air Force Occupational Measurement Center Lackland Air... Force Base, Texas 1 March 1975 I DISTRIBUTED BY: National Technical Information Service U. S. DEPARTMENT OF COMMERCE *I 11 5091 OCCUPATIONAL SURVEY...DISCUSSION OF BACKGROUJND INFORMATION --------------------------- xxvi 01L< R PREFACE This report presents the results cf detailed Air Force

Empty substrate integrated waveguide technology for E plane high-frequency and high-performance circuits

NASA Astrophysics Data System (ADS)

Belenguer, Angel; Cano, Juan Luis; Esteban, Héctor; Artal, Eduardo; Boria, Vicente E.

2017-01-01

Substrate integrated circuits (SIC) have attracted much attention in the last years because of their great potential of low cost, easy manufacturing, integration in a circuit board, and higher-quality factor than planar circuits. A first suite of SIC where the waves propagate through dielectric have been first developed, based on the well-known substrate integrated waveguide (SIW) and related technological implementations. One step further has been made with a new suite of empty substrate integrated waveguides, where the waves propagate through air, thus reducing the associated losses. This is the case of the empty substrate integrated waveguide (ESIW) or the air-filled substrate integrated waveguide (air-filled SIW). However, all these SIC are H plane structures, so classical H plane solutions in rectangular waveguides have already been mapped to most of these new SIC. In this paper a novel E plane empty substrate integrated waveguide (ESIW-E) is presented. This structure allows to easily map classical E plane solutions in rectangular waveguide to this new substrate integrated solution. It is similar to the ESIW, although more layers are needed to build the structure. A wideband transition (covering the frequency range between 33 GHz and 50 GHz) from microstrip to ESIW-E is designed and manufactured. Measurements are successfully compared with simulation, proving the validity of this new SIC. A broadband high-frequency phase shifter (for operation from 35 GHz to 47 GHz) is successfully implemented in ESIW-E, thus proving the good performance of this new SIC in a practical application.

ESR modes in a Strong-Leg Ladder in the Tomonaga-Luttinger Liquid Phase

NASA Astrophysics Data System (ADS)

Zvyagin, S.; Ozerov, M.; Maksymenko, M.; Wosnitza, J.; Honecker, A.; Landee, C. P.; Turnbull, M.; Furuya, S. C.; Giamarchi, T.

Magnetic excitations in the strong-leg quantum spin ladder compound (C7H10N)2CuBr4 (known as DIMPY) in the field-induced Tomonaga-Luttinger spin liquid phase are studied by means of high-field electron spin resonance (ESR) spectroscopy. The presence of a gapped ESR mode with unusual non-linear frequency-field dependence is revealed experimentally. Using a combination of analytic and exact diagonalization methods, we compute the dynamical structure factor and identify this mode with longitudinal excitations in the antisymmetric channel. We argue that these excitations constitute a fingerprint of the spin dynamics in a strong-leg spin-1/2 Heisenberg antiferromagnetic ladder and owe its ESR observability to the uniform Dzyaloshinskii-Moriya interaction. This work was partially supported by the DFG and Helmholtz Gemeinschaft (Germany), Swiss SNF under Division II, and ERC synergy UQUAM project. We acknowledge the support of the HLD at HZDR, member of the European Magnetic Field Laboratory (EMFL).

Dynamics of blood flow in a microfluidic ladder network

NASA Astrophysics Data System (ADS)

Maddala, Jeevan; Zilberman-Rudenko, Jevgenia; McCarty, Owen

The dynamics of a complex mixture of cells and proteins, such as blood, in perturbed shear flow remains ill-defined. Microfluidics is a promising technology for improving the understanding of blood flow under complex conditions of shear; as found in stent implants and in tortuous blood vessels. We model the fluid dynamics of blood flow in a microfluidic ladder network with dimensions mimicking venules. Interaction of blood cells was modeled using multiagent framework, where cells of different diameters were treated as spheres. This model served as the basis for predicting transition regions, collision pathways, re-circulation zones and residence times of cells dependent on their diameters and device architecture. Based on these insights from the model, we were able to predict the clot formation configurations at various locations in the device. These predictions were supported by the experiments using whole blood. To facilitate platelet aggregation, the devices were coated with fibrillar collagen and tissue factor. Blood was perfused through the microfluidic device for 9 min at a physiologically relevant venous shear rate of 600 s-1. Using fluorescent microscopy, we observed flow transitions near the channel intersections and at the areas of blood flow obstruction, which promoted larger thrombus formation. This study of integrating model predictions with experimental design, aids in defining the dynamics of blood flow in microvasculature and in development of novel biomedical devices.

Phonon and magnon dispersions of incommensurate spin ladder compound Sr14Cu24O41

NASA Astrophysics Data System (ADS)

Chen, Xi; Bansal, Dipanshu; Sullivan, Sean; Zhou, Jianshi; Delaire, Olivier; Shi, Li

There are a variety of compounds consisting of two or more interpenetrating sublattices with lattice periods incommensurate at least along one crystal axis. One example is spin ladder compound Sr14Cu24O41 consisting of incommensurate spin ladder and spin chain sublattices. It has been predicted that unique phonon modes occur in these compounds due to the relative motion of the sublattices. In the low-wavelength limit, there is only one longitudinal acoustic mode due to the rigid translation of both sublattices. In addition, one extra pseudo-acoustic mode is present due to relative sliding motions of the two sublattices. Although the theoretical aspects of the lattice dynamics of incommensurate compounds have been studied, there have been few experimental investigations on their phonon dynamics. In this work, single crystals of Sr14Cu24O41are grown by the traveling solvent floating zone method. The phonon dispersion of Sr14Cu24O41 is studied through inelastic neutron scattering measurements in order to better understand its phonon dynamics. In addition, its magnon dispersion is investigated and correlated to the large directional magnon thermal conductivity. The measurements reveal a wealth of intriguing features on phonons and magnons in the spin ladder compound. This work is supported by ARO MURI program under Award # W911NF-14-1-0016.

Optogenetic interrogation of neural circuits: technology for probing mammalian brain structures

PubMed Central

Zhang, Feng; Gradinaru, Viviana; Adamantidis, Antoine R; Durand, Remy; Airan, Raag D; de Lecea, Luis; Deisseroth, Karl

2015-01-01

Elucidation of the neural substrates underlying complex animal behaviors depends on precise activity control tools, as well as compatible readout methods. Recent developments in optogenetics have addressed this need, opening up new possibilities for systems neuroscience. Interrogation of even deep neural circuits can be conducted by directly probing the necessity and sufficiency of defined circuit elements with millisecond-scale, cell type-specific optical perturbations, coupled with suitable readouts such as electrophysiology, optical circuit dynamics measures and freely moving behavior in mammals. Here we collect in detail our strategies for delivering microbial opsin genes to deep mammalian brain structures in vivo, along with protocols for integrating the resulting optical control with compatible readouts (electrophysiological, optical and behavioral). The procedures described here, from initial virus preparation to systems-level functional readout, can be completed within 4–5 weeks. Together, these methods may help in providing circuit-level insight into the dynamics underlying complex mammalian behaviors in health and disease. PMID:20203662

Ising versus S U (2) 2 string-net ladder

NASA Astrophysics Data System (ADS)

Vidal, Julien

2018-03-01

We consider the string-net model obtained from S U (2) 2 fusion rules. These fusion rules are shared by two different sets of anyon theories. In this paper, we study the competition between the two corresponding non-Abelian quantum phases in the ladder geometry. A detailed symmetry analysis shows that the nontrivial low-energy sector corresponds to the transverse-field cluster model that displays a critical point described by the s o (2) 1 conformal field theory. Other sectors are obtained by freezing spins in this model.

The Development of Si and SiGe Technologies for Microwave and Millimeter-Wave Integrated Circuits

NASA Technical Reports Server (NTRS)

Ponchak, George E.; Alterovitz, Samuel A.; Katehi, Linda P. B.; Bhattacharya, Pallab K.

1997-01-01

Historically, microwave technology was developed by military and space agencies from around the world to satisfy their unique radar, communication, and science applications. Throughout this development phase, the sole goal was to improve the performance of the microwave circuits and components comprising the systems. For example, power amplifiers with output powers of several watts over broad bandwidths, low noise amplifiers with noise figures as low as 3 dB at 94 GHz, stable oscillators with low noise characteristics and high output power, and electronically steerable antennas were required. In addition, the reliability of the systems had to be increased because of the high monetary and human cost if a failure occurred. To achieve these goals, industry, academia and the government agencies supporting them chose to develop technologies with the greatest possibility of surpassing the state of the art performance. Thus, Si, which was already widely used for digital circuits but had material characteristics that were perceived to limit its high frequency performance, was bypassed for a progression of devices starting with GaAs Metal Semiconductor Field Effect Transistors (MESFETs) and ending with InP Pseudomorphic High Electron Mobility Transistors (PHEMTs). For each new material or device structure, the electron mobility increased, and therefore, the high frequency characteristics of the device were improved. In addition, ultra small geometry lithographic processes were developed to reduce the gate length to 0.1 pm which further increases the cutoff frequency. The resulting devices had excellent performance through the millimeter-wave spectrum.

Silica-on-silicon waveguide quantum circuits.

PubMed

Politi, Alberto; Cryan, Martin J; Rarity, John G; Yu, Siyuan; O'Brien, Jeremy L

2008-05-02

Quantum technologies based on photons will likely require an integrated optics architecture for improved performance, miniaturization, and scalability. We demonstrate high-fidelity silica-on-silicon integrated optical realizations of key quantum photonic circuits, including two-photon quantum interference with a visibility of 94.8 +/- 0.5%; a controlled-NOT gate with an average logical basis fidelity of 94.3 +/- 0.2%; and a path-entangled state of two photons with fidelity of >92%. These results show that it is possible to directly "write" sophisticated photonic quantum circuits onto a silicon chip, which will be of benefit to future quantum technologies based on photons, including information processing, communication, metrology, and lithography, as well as the fundamental science of quantum optics.

Control of Porosity in Ladder Polymers by Solvent-induced Aggregation

NASA Astrophysics Data System (ADS)

Brady, Michael; Gamo, Eri; Wang, Cheng; Xia, Yan

Porous polymers hold promise as materials for gas absorption, membranes, and organic electronics. In all of these applications, attaining in-plane ordering of backbones and thus porous free volume impacts the ability to adsorb gas, selectively filter molecules, and conduct charges. In this work, hard and soft x-ray scattering and soft x-ray spectroscopy are of focus to study the pore structure, induced by the solution-driven aggregation of ladder polymer thin films made of LP-1 and LP-2. Using GISAXS and AFM it is shown that thermal annealing drives the growth of crystallites in thin films. Due to the completely sp2nature of the ladder polymer backbones, it is expected that backbones are extremely stiff and thus preventing them from packing once left in a metastable state following casting. Therefore, the combination of GIWAXS and GISAXS will be shown to be critical in correctly understanding how pores develop in this 700 m2/g sorbent (N2). Finally, application in CO2/N2 separation membranes towards carbon sequestration will be presented that show gas selectivity is achieved through heteroatom incorporation and polymer blending. In this talk, focus will be placed on state-of-the-art x-ray scattering and spectroscopy, highlighting the importance of chemically sensitive structural information enabled by the combination of spectroscopy and scattering at play with the use of resonant soft x-rays.

Grand Research Plan for Neural Circuits of Emotion and Memory--current status of neural circuit studies in China.

PubMed

Zhu, Yuan-Gui; Cao, He-Qi; Dong, Er-Dan

2013-02-01

During recent years, major advances have been made in neuroscience, i.e., asynchronous release, three-dimensional structural data sets, saliency maps, magnesium in brain research, and new functional roles of long non-coding RNAs. Especially, the development of optogenetic technology provides access to important information about relevant neural circuits by allowing the activation of specific neurons in awake mammals and directly observing the resulting behavior. The Grand Research Plan for Neural Circuits of Emotion and Memory was launched by the National Natural Science Foundation of China. It takes emotion and memory as its main objects, making the best use of cutting-edge technologies from medical science, life science and information science. In this paper, we outline the current status of neural circuit studies in China and the technologies and methodologies being applied, as well as studies related to the impairments of emotion and memory. In this phase, we are making efforts to repair the current deficiencies by making adjustments, mainly involving four aspects of core scientific issues to investigate these circuits at multiple levels. Five research directions have been taken to solve important scientific problems while the Grand Research Plan is implemented. Future research into this area will be multimodal, incorporating a range of methods and sciences into each project. Addressing these issues will ensure a bright future, major discoveries, and a higher level of treatment for all affected by debilitating brain illnesses.

Electronic switches and control circuits: A compilation

NASA Technical Reports Server (NTRS)

1971-01-01

The innovations in this updated series of compilations dealing with electronic technology represents a carefully selected collection of items on electronic switches and control circuits. Most of the items are based on well-known circuit design concepts that have been simplified or refined to meet NASA's demanding requirement for reliability, simplicity, fail-safe characteristics, and the capability of withstanding environmental extremes.

Fiscal Viability, Conjunctive and Compensatory Models, and Career-Ladder Decisions: An Empirical Investigation.

ERIC Educational Resources Information Center

Mehrens, William A.; And Others

A study was undertaken to explore cost-effective ways of making career ladder teacher evaluation system decisions based on fewer measures, assessing the relationship of observational variables to other data and final decisions, and comparison of compensatory and conjunctive decision models. Data included multiple scores from eight data sources in…

A Simple Memristor Model for Circuit Simulations

NASA Astrophysics Data System (ADS)

Fullerton, Farrah-Amoy; Joe, Aaleyah; Gergel-Hackett, Nadine; Department of Chemistry; Physics Team

This work describes the development of a model for the memristor, a novel nanoelectronic technology. The model was designed to replicate the real-world electrical characteristics of previously fabricated memristor devices, but was constructed with basic circuit elements using a free widely available circuit simulator, LT Spice. The modeled memrsistors were then used to construct a circuit that performs material implication. Material implication is a digital logic that can be used to perform all of the same basic functions as traditional CMOS gates, but with fewer nanoelectronic devices. This memristor-based digital logic could enable memristors' use in new paradigms of computer architecture with advantages in size, speed, and power over traditional computing circuits. Additionally, the ability to model the real-world electrical characteristics of memristors in a free circuit simulator using its standard library of elements could enable not only the development of memristor material implication, but also the development of a virtually unlimited array of other memristor-based circuits.

Refrigeration and Cryogenics Career Ladder, AFSc 54530, 54550, and 54570.

DTIC Science & Technology

1983-07-01

STATES AIR FORCE D cl e 00l REFRIGERATION AND CRYOGENICS CAREER LADDER AFSCs 54530, 54550, AND 54570 AFPT 90-545-461 JULY 1983 ,-. 71983 - OCCUPATIONAL...been reviewed and is approved. PAUL T. RINGENBACH, Colonel, USAF WALTER E . DRISKILL, Ph.D. Commander Chief, Occupational Analysis Branch USAF...ASSIGNED SAMPLE AIRMAN 35 35 E -4 22 23 E -5 27 26 E -6 11 12 E -7 5 4 E -8 * E -9 * TOTALS 100 100 DENOTES LESS THAN ONE PERCENT TABLE 3 TAFHS

Transistor Level Circuit Experiments using Evolvable Hardware

NASA Technical Reports Server (NTRS)

Stoica, A.; Zebulum, R. S.; Keymeulen, D.; Ferguson, M. I.; Daud, Taher; Thakoor, A.

2005-01-01

The Jet Propulsion Laboratory (JPL) performs research in fault tolerant, long life, and space survivable electronics for the National Aeronautics and Space Administration (NASA). With that focus, JPL has been involved in Evolvable Hardware (EHW) technology research for the past several years. We have advanced the technology not only by simulation and evolution experiments, but also by designing, fabricating, and evolving a variety of transistor-based analog and digital circuits at the chip level. EHW refers to self-configuration of electronic hardware by evolutionary/genetic search mechanisms, thereby maintaining existing functionality in the presence of degradations due to aging, temperature, and radiation. In addition, EHW has the capability to reconfigure itself for new functionality when required for mission changes or encountered opportunities. Evolution experiments are performed using a genetic algorithm running on a DSP as the reconfiguration mechanism and controlling the evolvable hardware mounted on a self-contained circuit board. Rapid reconfiguration allows convergence to circuit solutions in the order of seconds. The paper illustrates hardware evolution results of electronic circuits and their ability to perform under 230 C temperature as well as radiations of up to 250 kRad.

Laser Integration on Silicon Photonic Circuits Through Transfer Printing

DTIC Science & Technology

2017-03-10

AFRL-AFOSR-UK-TR-2017-0019 Laser integration on silicon photonic circuits through transfer printing Gunther Roelkens UNIVERSITEIT GENT VZW Final...TYPE Final 3. DATES COVERED (From - To) 15 Sep 2015 to 14 Sep 2016 4. TITLE AND SUBTITLE Laser integration on silicon photonic circuits through...parallel integration of III-V lasers on silicon photonic integrated circuits. The report discusses the technological process that has been developed as

Josephson Circuits as Vector Quantum Spins

NASA Astrophysics Data System (ADS)

Samach, Gabriel; Kerman, Andrew J.

While superconducting circuits based on Josephson junction technology can be engineered to represent spins in the quantum transverse-field Ising model, no circuit architecture to date has succeeded in emulating the vector quantum spin models of interest for next-generation quantum annealers and quantum simulators. Here, we present novel Josephson circuits which may provide these capabilities. We discuss our rigorous quantum-mechanical simulations of these circuits, as well as the larger architectures they may enable. This research was funded by the Office of the Director of National Intelligence (ODNI) and the Intelligence Advanced Research Projects Activity (IARPA) under Air Force Contract No. FA8721-05-C-0002. The views and conclusions contained herein are those of the authors and should not be interpreted as necessarily representing the official policies or endorsements, either expressed or implied, of ODNI, IARPA, or the US Government.

Evaluating waste printed circuit boards recycling: Opportunities and challenges, a mini review.

PubMed

Awasthi, Abhishek Kumar; Zlamparet, Gabriel Ionut; Zeng, Xianlai; Li, Jinhui

2017-04-01

Rapid generation of waste printed circuit boards has become a very serious issue worldwide. Numerous techniques have been developed in the last decade to resolve the pollution from waste printed circuit boards, and also recover valuable metals from the waste printed circuit boards stream on a large-scale. However, these techniques have their own certain specific drawbacks that need to be rectified properly. In this review article, these recycling technologies are evaluated based on a strength, weaknesses, opportunities and threats analysis. Furthermore, it is warranted that, the substantial research is required to improve the current technologies for waste printed circuit boards recycling in the outlook of large-scale applications.

Circuit QED: generation of two-transmon-qutrit entangled states via resonant interaction

NASA Astrophysics Data System (ADS)

Ye, Xi-Mei; Zheng, Zhen-Fei; Lu, Dao-Ming; Yang, Chui-Ping

2018-04-01

We present a way to create entangled states of two superconducting transmon qutrits based on circuit QED. Here, a qutrit refers to a three-level quantum system. Since only resonant interaction is employed, the entanglement creation can be completed within a short time. The degree of entanglement for the prepared entangled state can be controlled by varying the weight factors of the initial state of one qutrit, which allows the prepared entangled state to change from a partially entangled state to a maximally entangled state. Because a single cavity is used, only resonant interaction is employed, and none of identical qutrit-cavity coupling constant, measurement, and auxiliary qutrit is needed, this proposal is easy to implement in experiments. The proposal is quite general and can be applied to prepare a two-qutrit partially or maximally entangled state with two natural or artificial atoms of a ladder-type level structure, coupled to an optical or microwave cavity.

Fractal Electronic Circuits Assembled From Nanoclusters

NASA Astrophysics Data System (ADS)

Fairbanks, M. S.; McCarthy, D.; Taylor, R. P.; Brown, S. A.

2009-07-01

Many patterns in nature can be described using fractal geometry. The effect of this fractal character is an array of properties that can include high internal connectivity, high dispersivity, and enhanced surface area to volume ratios. These properties are often desirable in applications and, consequently, fractal geometry is increasingly employed in technologies ranging from antenna to storm barriers. In this paper, we explore the application of fractal geometry to electrical circuits, inspired by the pervasive fractal structure of neurons in the brain. We show that, under appropriate growth conditions, nanoclusters of Sb form into islands on atomically flat substrates via a process close to diffusion-limited aggregation (DLA), establishing fractal islands that will form the basis of our fractal circuits. We perform fractal analysis of the islands to determine the spatial scaling properties (characterized by the fractal dimension, D) of the proposed circuits and demonstrate how varying growth conditions can affect D. We discuss fabrication approaches for establishing electrical contact to the fractal islands. Finally, we present fractal circuit simulations, which show that the fractal character of the circuit translates into novel, non-linear conduction properties determined by the circuit's D value.

Maximum Temperature Detection System for Integrated Circuits

NASA Astrophysics Data System (ADS)

Frankiewicz, Maciej; Kos, Andrzej

2015-03-01

The paper describes structure and measurement results of the system detecting present maximum temperature on the surface of an integrated circuit. The system consists of the set of proportional to absolute temperature sensors, temperature processing path and a digital part designed in VHDL. Analogue parts of the circuit where designed with full-custom technique. The system is a part of temperature-controlled oscillator circuit - a power management system based on dynamic frequency scaling method. The oscillator cooperates with microprocessor dedicated for thermal experiments. The whole system is implemented in UMC CMOS 0.18 μm (1.8 V) technology.

South Dakota Statewide Core Curriculum, Career Ladder, and Challenge System. A Case History.

ERIC Educational Resources Information Center

Brekke, Donald G.; Gildseth, Wayne M.

The South Dakota Core Curriculum Project involving the career ladder approach to health manpower training, which began in 1970, had seven objectives including the following: (1) To organize a Health Manpower Council for the entire State; (2) to define the areas of basic commonality among the various training programs; and (3) to develop a core…

Career Mobility: Implementing the Ladder Concept in Associate Degree and Practical Nursing Curricula.

ERIC Educational Resources Information Center

Story, Donna Ketchum

Designing a career ladder curriculum is not simply taking an existing practical nurse curriculum and an associate degree nursing curriculum and placing one after the other. The curriculum is designed to produce students who are competent practitioners as practical nurses at the end of the first level and then allow them to continue for an…

Analysis of an "off-ladder" allele at the Penta D short tandem repeat locus.

PubMed

Yang, Y L; Wang, J G; Wang, D X; Zhang, W Y; Liu, X J; Cao, J; Yang, S L

2015-11-25

Kinship testing of a father and his son from Guangxi, China, the location of the Zhuang minority people, was performed using the PowerPlex® 18D System with a short tandem repeat typing kit. The results indicated that both the father and his son had an off-ladder allele at the Penta D locus, with a genetic size larger than that of the maximal standard allelic ladder. To further identify this locus, monogenic amplification, gene cloning, and genetic sequencing were performed. Sequencing analysis demonstrated that the fragment size of the Penta D-OL locus was 469 bp and the core sequence was [AAAGA]21, also called Penta D-21. The rare Penta D-21 allele was found to be distributed among the Zhuang population from the Guangxi Zhuang Autonomous Region of China; therefore, this study improved the range of DNA data available for this locus and enhanced our ability for individual identification of gene loci.

Designing Novel Quaternary Quantum Reversible Subtractor Circuits

NASA Astrophysics Data System (ADS)

Haghparast, Majid; Monfared, Asma Taheri

2018-01-01

Reversible logic synthesis is an important area of current research because of its ability to reduce energy dissipation. In recent years, multiple valued logic has received great attention due to its ability to reduce the width of the reversible circuit which is a main requirement in quantum technology. Subtractor circuits are between major components used in quantum computers. In this paper, we will discuss the design of a quaternary quantum reversible half subtractor circuit using quaternary 1-qudit, 2-qudit Muthukrishnan-Stroud and 3-qudit controlled gates and a 2-qudit Generalized quaternary gate. Then a design of a quaternary quantum reversible full subtractor circuit based on the quaternary half subtractor will be presenting. The designs shall then be evaluated in terms of quantum cost, constant input, garbage output, and hardware complexity. The proposed quaternary quantum reversible circuits are the first attempt in the designing of the aforementioned subtractor.

Computer programs: Electronic circuit design criteria: A compilation

NASA Technical Reports Server (NTRS)

1973-01-01

A Technology Utilization Program for the dissemination of information on technological developments which have potential utility outside the aerospace community is presented. The 21 items reported herein describe programs that are applicable to electronic circuit design procedures.

Assessment of SOI Devices and Circuits at Extreme Temperatures

NASA Technical Reports Server (NTRS)

Elbuluk, Malik; Hammoud, Ahmad; Patterson, Richard L.

2007-01-01

Electronics designed for use in future NASA space exploration missions are expected to encounter extreme temperatures and wide thermal swings. Such missions include planetary surface exploration, bases, rovers, landers, orbiters, and satellites. Electronics designed for such applications must, therefore, be able to withstand exposure to extreme temperatures and to perform properly for the duration of mission. The Low Temperature Electronics Program at the NASA Glenn Research Center focuses on research and development of electrical devices, circuits, and systems suitable for applications in deep space exploration missions and aerospace environment. Silicon-On-Insulator (SOI) technology has been under active consideration in the electronics industry for many years due to the advantages that it can provide in integrated circuit (IC) chips and computer processors. Faster switching, less power, radiationtolerance, reduced leakage, and high temp-erature capability are some of the benefits that are offered by using SOI-based devices. A few SOI circuits are available commercially. However, there is a noticeable interest in SOI technology for different applications. Very little data, however, exist on the performance of such circuits under cryogenic temperatures. In this work, the performance of SOI integrated circuits, evaluated under low temperature and thermal cycling, are reported. In particular, three examples of SOI circuits that have been tested for operation at low at temperatures are given. These circuits are SOI operational amplifiers, timers and power MOSFET drivers. The investigations were carried out to establish a baseline on the functionality and to determine suitability of these circuits for use in space exploration missions at cryogenic temperatures. The findings are useful to mission planners and circuit designers so that proper selection of electronic parts can be made, and risk assessment can be established for such circuits for use in space missions.

Influence of Stress State, Stress Orientation, and Rock Properties on the Development of Deformation-Band 'Ladder' Arrays in Porous Sandstone

NASA Astrophysics Data System (ADS)

Schultz, R. A.; Soliva, R.; Fossen, H.

2013-12-01

Deformation bands in porous rocks tend to develop into spatially organized arrays that display a variety of lengths and thicknesses, and their geometries and arrangements are of interest with respect to fluid flow in reservoirs. Field examples of deformation band arrays in layered clastic sequences suggest that the development of classic deformation band arrays, such as ladders and conjugate sets, and the secondary formation of through-going faults appear to be related to the physical properties of the host rock, the orientation of stratigraphic layers relative to the far-field stress state, and the evolution of the local stress state within the developing array. We have identified several field examples that demonstrate changes in band properties, such as type and orientation, as a function of one or more of these three main factors. Normal-sense deformation-band arrays such as those near the San Rafael Swell (Utah) develop three-dimensional ladder-style arrays at a high angle to the maximum compression direction; these cataclastic shear bands form at acute angles to the maximum compression not very different from that of the optimum frictional sliding plane, thus facilitating the eventual nucleation of a through-going fault. At Orange quarry (France), geometrically conjugate sets of reverse-sense compactional shear bands form with angles to the maximum compression direction that inhibit fault nucleation within them; the bands in this case also form at steep enough angles to bedding that stratigraphic heterogeneities within the deforming formation were apparently not important. Two exposures of thrust-sense ladders at Buckskin Gulch (Utah) demonstrate the importance of host-rock properties, bedding-plane involvement, and local stress perturbations on band-array growth. In one ladder, thrust-sense shear deformation bands nucleated along suitably oriented bedding planes, creating overprinting sets of compaction bands that can be attributed to layer properties and

Computational study of Zn-doped quantum spin chains and ladders

NASA Astrophysics Data System (ADS)

Laukamp, Markus

In this dissertation, the powerful Density Matrix Renormalization Group method is applied to examine the properties of spin models. The method allows to determine accurately the properties of low lying states of finite systems of large sizes. The results gained with this technique are compared to results generated with exact diagonalization and Monte Carlo techniques. Spin models have been proposed to describe dimerized chains, ladders, two dimensional antiferromagnets, and other compounds. Here the focus is on the case where some spins are replaced by spinless vacancies. This happens e.g. upon Zn doping, when Cusp{2+} atoms are replaced by Znsp{2+}. A small percentage of vacancies rapidly destroys the spin gap, and their presence induces enhanced antiferromagnetic correlations near those vacancies. Since the phenomenon of enhanced antiferromagnetism is found to occur in several models and cluster geometries, a common simple explanation for its presence may exist. In this thesis it is argued that the resonating-valence-bond character of the spin correlations at short distances of a large variety of models is responsible for the presence of robust staggered spin correlations near vacancies and lattice edges. The phenomenon takes place regardless of the long distance properties of the ground state, and it is caused by a "pruning" of the available spin singlets in the vicinity of the vacancies. The effect produces a broadening of the low temperature NMR signal for the compounds analyzed here. This broadening should be experimentally observable in the structurally dimerized chain systems Cu(NOsb3)sb{*}2.5Hsb2O,\\ CuWOsb4,\\ (VO)sb2Psb2Osb7, and Srsb{14}Cusb{24}Osb{41}, in ladder materials such as SrCusb2Osb3, in the spin-Peierls systems CuGeOsb3 and NaVsb2Osb5, and in several others since it is a universal effect common to a wide variety of models and compounds. In addition, it is argued that the Neel order observed in SrCusb2Osb3 upon Zn doping is induced by the local

Negative Difference Resistance and Its Application to Construct Boolean Logic Circuits

NASA Astrophysics Data System (ADS)

Nikodem, Maciej; Bawiec, Marek A.; Surmacz, Tomasz R.

Electronic circuits based on nanodevices and quantum effect are the future of logic circuits design. Today's technology allows constructing resonant tunneling diodes, quantum cellular automata and nanowires/nanoribbons that are the elementary components of threshold gates. However, synthesizing a threshold circuit for an arbitrary logic function is still a challenging task where no efficient algorithms exist. This paper focuses on Generalised Threshold Gates (GTG), giving the overview of threshold circuit synthesis methods and presenting an algorithm that considerably simplifies the task in case of GTG circuits.

Electronic structure reconstruction across the antiferromagnetic transition in TaFe₁̣₂₃Te₃ spin ladder

DOE PAGES

Xu, Min; Wang, Li -Min; Peng, Rui; ...

2015-02-01

With angle-resolved photoemission spectroscopy, we studied the electronic structure of TaFe₁̣₂₃Te₃, a two-leg spin ladder compound with a novel antiferromagnetic ground state. Quasi-two-dimensional Fermi surface is observed, with sizable inter-ladder hopping. Moreover, instead of observing an energy gap at the Fermi surface in the antiferromagnetic state, we observed the shifts of various bands. Combining these observations with density-functional-theory calculations, we propose that the large scale reconstruction of the electronic structure, caused by the interactions between coexisting itinerant electrons and local moments, is most likely the driving force of the magnetic transition. Thus TaFe₁̣₂₃Te₃ serves as a simpler platform that containsmore » similar ingredients as the parent compounds of iron-based superconductors.« less

Convergence and Periodic Solutions for the Input Impedance of a Standard Ladder Network

ERIC Educational Resources Information Center

Ucak, C.; Acar, C.

2007-01-01

The input impedance of an infinite ladder network is computed by using the recursive relation and by assuming that the input impedance does not change when a new block is added to the network. However, this assumption is not true in general and standard textbooks do not always treat these networks correctly. This paper develops a general solution…

S,N-Heteroacene-Based Copolymers for Highly Efficient Organic Field Effect Transistors and Organic Solar Cells: Critical Impact of Aromatic Subunits in the Ladder π-System.

PubMed

Chung, Chin-Lung; Chen, Hsieh-Chih; Yang, Yun-Siou; Tung, Wei-Yao; Chen, Jian-Wei; Chen, Wen-Chang; Wu, Chun-Guey; Wong, Ken-Tsung

2018-02-21

Three novel donor-acceptor alternating polymers containing ladder-type pentacyclic heteroacenes (PBo, PBi, and PT) are synthesized, characterized, and further applied to organic field effect transistors (OFETs) and polymer solar cells. Significant aspects of quinoidal characters, electrochemical properties, optical absorption, frontier orbitals, backbone coplanarity, molecular orientation, charge carrier mobilities, morphology discrepancies, and the corresponding device performances are notably different with various heteroarenes. PT exhibits a stronger quinoidal mesomeric structure, linear and coplanar conformation, smooth surface morphology, and better bimodal crystalline structures, which is beneficial to extend the π-conjugation and promotes charge transport via 3-D transport pathways and in consequence improves overall device performances. Organic photovoltaics based on the PT polymer achieve a power conversion efficiency of 6.04% along with a high short-circuit current density (J SC ) of 14.68 mA cm -2 , and a high hole mobility of 0.1 cm 2 V -1 s -1 is fulfilled in an OFET, which is superior to those of its counterparts, PBi and PBo.

Avionics Instrument Systems Specialist Career Ladder: AFSCs 32531, 32551, 31571, and 32591. Occupational Survey Report.

ERIC Educational Resources Information Center

Air Force Occupational Measurement Center, Lackland AFB, TX.

The Avionics Instrument Systems career ladder (AFSC 325X1) provides flight line and shop maintenance training on aircraft instrument systems, electromechancial instruments, components, and test equipment. Duties involve inspecting, removing, installing, repairing, operating, troubleshooting, overhauling, and modifying systems such as flight and…

Educational Characteristics of Paraprofessionals in Southern California: A Survey of Their Career Ladder Needs.

ERIC Educational Resources Information Center

Ochoa, Alberto M.; Wright, Pamela G.

The purpose of this study was to identify the career ladder needs of paraprofessionals as required by both California State and Federal educational mandates. Findings, gathered by questionnaires returned by 594 aides in seven southern and central Californian counties, are discussed in terms of the following: (1) personal characteristics; (2)…

The Health Services Mobility Study Method of Task Analysis and Curriculum Design. Research Report No. 11. Volume 3: Using the Computer to Develop Job Ladders.

ERIC Educational Resources Information Center

Gilpatrick, Eleanor

This document is volume 3 of a four-volume report which describes the components of the Health Services Mobility Study (HSMS) method of task analysis, job ladder design, and curriculum development. Divided into four chapters, volume 3 is a manual for using HSMS computer based statistical procedures to design job structures and job ladders. Chapter…

New dynamic FET logic and serial memory circuits for VLSI GaAs technology

NASA Technical Reports Server (NTRS)

Eldin, A. G.

1991-01-01

The complexity of GaAs field effect transistor (FET) very large scale integration (VLSI) circuits is limited by the maximum power dissipation while the uniformity of the device parameters determines the functional yield. In this work, digital GaAs FET circuits are presented that eliminate the DC power dissipation and reduce the area to 50% of that of the conventional static circuits. Its larger tolerance to device parameter variations results in higher functional yield.

CMOS-based optical energy harvesting circuit for biomedical and Internet of Things devices

NASA Astrophysics Data System (ADS)

Nattakarn, Wuthibenjaphonchai; Ishizu, Takaaki; Haruta, Makito; Noda, Toshihiko; Sasagawa, Kiyotaka; Tokuda, Takashi; Sawan, Mohamad; Ohta, Jun

2018-04-01

In this work, we present a novel CMOS-based optical energy harvesting technology for implantable and Internet of Things (IoT) devices. In the proposed system, a CMOS energy-harvesting circuit accumulates a small amount of photoelectrically converted energy in an external capacitor, and intermittently supplies this power to a target device. Two optical energy-harvesting circuit types were implemented and evaluated. Furthermore, we developed a photoelectrically powered optical identification (ID) circuit that is suitable for IoT technology applications.

Nanophotonic integrated circuits from nanoresonators grown on silicon.

PubMed

Chen, Roger; Ng, Kar Wei; Ko, Wai Son; Parekh, Devang; Lu, Fanglu; Tran, Thai-Truong D; Li, Kun; Chang-Hasnain, Connie

2014-07-07

Harnessing light with photonic circuits promises to catalyse powerful new technologies much like electronic circuits have in the past. Analogous to Moore's law, complexity and functionality of photonic integrated circuits depend on device size and performance scale. Semiconductor nanostructures offer an attractive approach to miniaturize photonics. However, shrinking photonics has come at great cost to performance, and assembling such devices into functional photonic circuits has remained an unfulfilled feat. Here we demonstrate an on-chip optical link constructed from InGaAs nanoresonators grown directly on a silicon substrate. Using nanoresonators, we show a complete toolkit of circuit elements including light emitters, photodetectors and a photovoltaic power supply. Devices operate with gigahertz bandwidths while consuming subpicojoule energy per bit, vastly eclipsing performance of prior nanostructure-based optoelectronics. Additionally, electrically driven stimulated emission from an as-grown nanostructure is presented for the first time. These results reveal a roadmap towards future ultradense nanophotonic integrated circuits.

Implementation of Evidence-Based Practice in Relation to a Clinical Nursing Ladder System: A National Survey in Taiwan

PubMed Central

Weng, Yi-Hao; Chen, Chiehfeng; Kuo, Ken N; Yang, Chun-Yuh; Lo, Heng-Lien; Chen, Kee-Hsin; Chiu, Ya-Wen

2015-01-01

Background Although evidence-based practice (EBP) has been widely investigated, few studies have investigated its correlation with a clinical nursing ladder system. The current national study evaluates whether EBP implementation has been incorporated into the clinical ladder system. Methods A cross-sectional questionnaire survey was conducted nationwide of registered nurses among regional hospitals of Taiwan in January to April 2011. Subjects were categorized into beginning nurses (N1 and N2) and advanced nurses (N3 and N4) by the clinical ladder system. Multivariate logistic regression model was used to adjust for possible confounding demographic factors. Results Valid postal questionnaires were collected from 4,206 nurses, including 2,028 N1, 1,595 N2, 412 N3, and 171 N4 nurses. Advanced nurses were more aware of EBP than beginning nurses (p < 0.001; 90.7% vs. 78.0%). In addition, advanced nurses were more likely to hold positive beliefs about and attitudes toward EBP (p < 0.001) and possessed more sufficient knowledge of and skills in EBP (p < 0.001). Furthermore, they more often implemented EBP principles (p < 0.001) and accessed online evidence-based retrieval databases (p < 0.001). The most common motivation for using online databases was self-learning for advanced nurses and positional promotion for beginning nurses. Multivariate logistic regression analyses showed advanced nurses were more aware of EBP, had higher knowledge and skills of EBP, and more often implemented EBP than beginning nurses. Linking Evidence to Action The awareness of, beliefs in, attitudes toward, knowledge of, skills in, and behaviors of EBP among advanced nurses were better than those among beginning nurses. The data indicate that a clinical ladder system can serve as a useful means to enhance EBP implementation. PMID:25588625

A Statewide Decentralized Approach to Public School Reform: The Case of Career Ladders in Utah.

ERIC Educational Resources Information Center

Malen, Betty; Murphy, Michael J.

1985-01-01

In 1984, the Utah legislature enacted a career ladder bill encouraging all local districts to develop plans for restructuring teachers' compensation and promotion options. An independent, bipartisan taskforce then created a statewide, decentralized model that increases educators' power, minimizes merit and staff differentiation, and fosters…

Electronic structure and magnetic properties of the strong-rung spin-1 ladder compound Rb3Ni2(NO3)7

NASA Astrophysics Data System (ADS)

Pchelkina, Z. V.; Mazurenko, V. V.; Volkova, O. S.; Deeva, E. B.; Morozov, I. V.; Shutov, V. V.; Troyanov, S. I.; Werner, J.; Koo, C.; Klingeler, R.; Vasiliev, A. N.

2018-04-01

Rb3Ni2(NO3)7 was obtained by crystallization from anhydrous nitric acid solution of rubidium nitrate and nickel nitrate hexahydrate. The crystal structure determined on single crystals implies isolated spin-1 two-leg ladders of Ni2 + ions connected by (NO3)- groups as basic elements. Magnetic susceptibility, specific heat in magnetic fields up to 9 T, magnetization, and high-frequency electron spin resonance studies performed on powder samples show the absence of long-range magnetic order at T ≥2 K. Electronic structure calculations and the detailed analysis of the experimental data enable quantitative estimates of the relevant parameters of the S =1 ladders in Rb3Ni2(NO3)7 . The rung coupling J1=10.16 K, the leg coupling J2=1.5 K, and the Ising-type anisotropy |A |=8.6 K are obtained. The scenario of a valence-bond solidlike quantum ground state realized in the two-leg Ni2 + ladders is further corroborated by model simulations of the magnetic susceptibility.

The Earnings Ladder. Who's at the Bottom? Who's at the Top? Statistical Brief.

ERIC Educational Resources Information Center

Bureau of the Census (DOC), Washington, DC. Economics and Statistics Administration.

Data collected by the March Current Population Survey were used to identify which groups of year-round, full-time civilian workers aged 16 and older were most likely to be at the top and bottom of the earnings ladder. Women, young workers, less-educated individuals, and Hispanics were most likely to earn less than $13,091 (1992 constant dollars),…

[Application of general retention time formula for gradient liquid chromatography in the studies of ladder-like gradient elution].

PubMed

Sun, Xiaoli; Hao, Weiqiang; Wang, Junde; Di, Bin; Chen, Qiang; Zhuang, Wei; Yu, Qiang; Zhang, Peipei

2013-08-01

By not explicitly specifying the type of solvent strength model, the features of ladder-like gradient elution were studied based on the general retention time formula that was derived in our previous work. For the case where the solute is eluted at like gradient, we derived the expression that connects the mobile phase composition (phiR), at which the solute is eluted from the column, with the gradient slope (B). It was shown that phiR will increase with the increase of B in this case. For the case where the solute is eluted at the last isocratic segment of the ladder-like gradient, it was proven that the retention time (tR) will correlate linearly with the reciprocal of the gradient slope (1/B) when the initial and final mobile phase compositions are set to be constant. In experiments, by taking biphenyl as the sample, the values of retention time in isocratic and gradient elution were measured on a C18 column by using a mixture of methanol and water as the mobile phase. The experimental values were found to be well consistent with the theoretical values that were calculated from the expressions. These expressions will be helpful to understand the features of the ladder-like gradient in practice.

Lithography for enabling advances in integrated circuits and devices.

PubMed

Garner, C Michael

2012-08-28

Because the transistor was fabricated in volume, lithography has enabled the increase in density of devices and integrated circuits. With the invention of the integrated circuit, lithography enabled the integration of higher densities of field-effect transistors through evolutionary applications of optical lithography. In 1994, the semiconductor industry determined that continuing the increase in density transistors was increasingly difficult and required coordinated development of lithography and process capabilities. It established the US National Technology Roadmap for Semiconductors and this was expanded in 1999 to the International Technology Roadmap for Semiconductors to align multiple industries to provide the complex capabilities to continue increasing the density of integrated circuits to nanometre scales. Since the 1960s, lithography has become increasingly complex with the evolution from contact printers, to steppers, pattern reduction technology at i-line, 248 nm and 193 nm wavelengths, which required dramatic improvements of mask-making technology, photolithography printing and alignment capabilities and photoresist capabilities. At the same time, pattern transfer has evolved from wet etching of features, to plasma etch and more complex etching capabilities to fabricate features that are currently 32 nm in high-volume production. To continue increasing the density of devices and interconnects, new pattern transfer technologies will be needed with options for the future including extreme ultraviolet lithography, imprint technology and directed self-assembly. While complementary metal oxide semiconductors will continue to be extended for many years, these advanced pattern transfer technologies may enable development of novel memory and logic technologies based on different physical phenomena in the future to enhance and extend information processing.

An Intrinsically Switchable Ladder-Type Ferroelectric BST-on-Si Composite FBAR Filter.

PubMed

Lee, Seungku; Mortazawi, Amir

2016-03-01

This paper presents a ladder-type bulk acoustic wave (BAW) intrinsically switchable filter based on ferroelectric thin-film bulk acoustic resonators (FBARs). The switchable filter can be turned on and off by the application of an external bias voltage due to the electrostrictive effect in thin-film ferroelectrics. In this paper, Barium Strontium Titanate (BST) is used as the ferroelectric material. A systematic design approach for switchable ladder-type ferroelectric filters is provided based on required filter specifications. A switchable filter is implemented in the form of a BST-on-Si composite structure to control the effective electromechanical coupling coefficient of FBARs. As an experimental verification, a 2.5-stage intrinsically switchable BST-on-Si composite FBAR filter is designed, fabricated, and measured. Measurement results for a typical BST-on-Si composite FBAR show a resonator mechanical quality factor (Q(m)) of 971, as well as a (Q(m)) × f of 2423 GHz. The filter presented here provides a measured insertion loss of 7.8 dB, out-of-band rejection of 26 dB, and fractional bandwidth of 0.33% at 2.5827 GHz when the filter is in the on state at a dc bias of 40 V. In its off state, the filter exhibits an isolation of 31 dB.

Elements configuration of the open lead test circuit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fukuzaki, Yumi, E-mail: 14514@sr.kagawa-nct.ac.jp; Ono, Akira

In the field of electronics, small electronic devices are widely utilized because they are easy to carry. The devices have various functions by user’s request. Therefore, the lead’s pitch or the ball’s pitch have been narrowed and high-density printed circuit board has been used in the devices. Use of the ICs which have narrow lead pitch makes normal connection difficult. When logic circuits in the devices are fabricated with the state-of-the-art technology, some faults have occurred more frequently. It can be divided into types of open faults and short faults. We have proposed a new test method using a testmore » circuit in the past. This paper propose elements configuration of the test circuit.« less

Shaping Tennessee's Career Ladder Program--1985. Part 2: Improving Teacher Quality through Incentives Project.

ERIC Educational Resources Information Center

Hadler, Janet R.; Carlson, Deborah L.

Outcomes of Tennessee's Career Ladder Program are presented in this report, with a focus on the early implementation stage and perceptions of teachers and administrators. Methodology involved two sets of interviews with participating teachers and administrators from 18 schools and a statewide survey of 1,039 out of 2,105 faculty from 54 schools.…

Note: Fully integrated active quenching circuit achieving 100 MHz count rate with custom technology single photon avalanche diodes.

PubMed

Acconcia, G; Labanca, I; Rech, I; Gulinatti, A; Ghioni, M

2017-02-01

The minimization of Single Photon Avalanche Diodes (SPADs) dead time is a key factor to speed up photon counting and timing measurements. We present a fully integrated Active Quenching Circuit (AQC) able to provide a count rate as high as 100 MHz with custom technology SPAD detectors. The AQC can also operate the new red enhanced SPAD and provide the timing information with a timing jitter Full Width at Half Maximum (FWHM) as low as 160 ps.

Commutation circuit for an HVDC circuit breaker

DOEpatents

Premerlani, William J.

1981-01-01

A commutation circuit for a high voltage DC circuit breaker incorporates a resistor capacitor combination and a charging circuit connected to the main breaker, such that a commutating capacitor is discharged in opposition to the load current to force the current in an arc after breaker opening to zero to facilitate arc interruption. In a particular embodiment, a normally open commutating circuit is connected across the contacts of a main DC circuit breaker to absorb the inductive system energy trapped by breaker opening and to limit recovery voltages to a level tolerable by the commutating circuit components.

Commutation circuit for an HVDC circuit breaker

DOEpatents

Premerlani, W.J.

1981-11-10

A commutation circuit for a high voltage DC circuit breaker incorporates a resistor capacitor combination and a charging circuit connected to the main breaker, such that a commutating capacitor is discharged in opposition to the load current to force the current in an arc after breaker opening to zero to facilitate arc interruption. In a particular embodiment, a normally open commutating circuit is connected across the contacts of a main DC circuit breaker to absorb the inductive system energy trapped by breaker opening and to limit recovery voltages to a level tolerable by the commutating circuit components. 13 figs.

Valence bond and von Neumann entanglement entropy in Heisenberg ladders.

PubMed

Kallin, Ann B; González, Iván; Hastings, Matthew B; Melko, Roger G

2009-09-11

We present a direct comparison of the recently proposed valence bond entanglement entropy and the von Neumann entanglement entropy on spin-1/2 Heisenberg systems using quantum Monte Carlo and density-matrix renormalization group simulations. For one-dimensional chains we show that the valence bond entropy can be either less or greater than the von Neumann entropy; hence, it cannot provide a bound on the latter. On ladder geometries, simulations with up to seven legs are sufficient to indicate that the von Neumann entropy in two dimensions obeys an area law, even though the valence bond entanglement entropy has a multiplicative logarithmic correction.

Demonstration of the Jaynes-Cummings ladder with Rydberg-dressed atoms

DOE PAGES

Lee, Jongmin; Martin, Michael J.; Jau, Yuan-Yu; ...

2017-04-06

Here, we observe the nonlinearity of the Jaynes-Cummings (JC) ladder in the Autler-Townes spectroscopy of the hyperfine ground states for a Rydberg-dressed two-atom system. The role of the two-level system in the JC model is played by the presence or absence of a collective Rydberg excitation, and the bosonic mode manifests as the number n of single-atom spin flips, symmetrically distributed between the atoms. We also measure the normal-mode splitting and √ n nonlinearity as a function of detuning and Rabi frequency, thereby experimentally establishing the isomorphism with the JC model.

Examining the technology acceptance for dismantling of waste printed circuit boards in light of recycling and environmental concerns.

PubMed

Duan, Huabo; Hou, Kun; Li, Jinhui; Zhu, Xiaodong

2011-03-01

The dismantling of printed circuit board assemblies (PCBAs) and the recovery of their useful materials can lead to serious environmental impacts mainly due to their complicated physical structure and the variety of toxic elements contained in their material composition. So far, less attention has been paid to their responsible recycling compared to that of bare printed circuit boards. Combined with other materials recovery process, proper dismantling of PCBAs is beneficial to conserve scarce resources, reuse the components, and eliminate or safely dispose of hazardous materials. In analyzing the generation, resources potential and hazardous risk of scrap PCBAs, technologies used for the dismantling of waste PCBAs have been widely investigated and reviewed from the aspects of both industrial application and laboratory-scale studies. In addition, the feasibility of PCBA dismantling has been discussed, the determinants of which, including the heating conditions and mechanical properties have been identified. Moreover, this paper evaluates the environmental consequences caused by the dismantling of PCBAs. Copyright © 2010 Elsevier Ltd. All rights reserved.

Recycle technology for recovering resources and products from waste printed circuit boards.

PubMed

Li, Jia; Lu, Hongzhou; Guo, Jie; Xu, Zhenming; Zhou, Yaohe

2007-03-15

The printed circuit board (PCB) contains nearly 28% metals that are abundant non-ferrous metals such as Cu, Al, Sn, etc. The purity of precious metals in PCBs is more than 10 times higher than that of rich-content minerals. Therefore, recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Chemical and mechanical methods are two traditional recycling processes for waste PCBs. However, the prospect of chemical methods will be limited since the emission of toxic liquid or gas brings secondary pollution to the environment during the process. Mechanical processes, such as shape separation, jigging, density-based separation, and electrostatic separation have been widely utilized in the recycling industry. But, recycling of waste PCBs is only beginning. In this study, a total of 400 kg of waste PCBs was processed by a recycle technology without negative impact to the environment. The technology contained mechanical two-step crushing, corona electrostatic separating, and recovery. The results indicated that (i) two-step crushing was an effect process to strip metals from base plates completely; (ii) the size of particles between 0.6 and 1.2 mm was suitable for corona electrostatic separating during industrial application; and (iii) the nonmetal of waste PCBs attained 80% weight of a kind of nonmetallic plate that expanded the applying prospect of waste nonmetallic materials.

SU(3)_C× SU(2)_L× U(1)_Y( × U(1)_X ) as a symmetry of division algebraic ladder operators

NASA Astrophysics Data System (ADS)

Furey, C.

2018-05-01

We demonstrate a model which captures certain attractive features of SU(5) theory, while providing a possible escape from proton decay. In this paper we show how ladder operators arise from the division algebras R, C, H, and O. From the SU( n) symmetry of these ladder operators, we then demonstrate a model which has much structural similarity to Georgi and Glashow's SU(5) grand unified theory. However, in this case, the transitions leading to proton decay are expected to be blocked, given that they coincide with presumably forbidden transformations which would incorrectly mix distinct algebraic actions. As a result, we find that we are left with G_{sm} = SU(3)_C× SU(2)_L× U(1)_Y / Z_6. Finally, we point out that if U( n) ladder symmetries are used in place of SU( n), it may then be possible to find this same G_{sm}=SU(3)_C× SU(2)_L× U(1)_Y / Z_6, together with an extra U(1)_X symmetry, related to B-L.

Magnetic properties and pairing tendencies of the iron-based superconducting ladder BaFe 2 S 3 : Combined ab initio and density matrix renormalization group study

DOE PAGES

Patel, Niravkumar D.; Nocera, Alberto; Alvarez, Gonzalo; ...

2016-08-10

The recent discovery of superconductivity under high pressure in the two-leg ladder compound BaFe 2S 3 [H. Takahashi et al., Nat. Mater. 14, 1008 (2015)] opens a broad avenue of research, because it represents the first report of pairing tendencies in a quasi-one-dimensional iron-based high-critical-temperature superconductor. Similarly, as in the case of the cuprates, ladders and chains can be far more accurately studied using many-body techniques and model Hamiltonians than their layered counterparts, particularly if several orbitals are active. In this publication, we derive a two-orbital Hubbard model from first principles that describes individual ladders of BaFe 2S 3. Themore » model is studied with the density matrix renormalization group. These first reported results are exciting for two reasons: (i) at half-filling, ferromagnetic order emerges as the dominant magnetic pattern along the rungs of the ladder, and antiferromagnetic order along the legs, in excellent agreement with neutron experiments; and (ii) with hole doping, pairs form in the strong coupling regime, as found by studying the binding energy of two holes doped on the half-filled system. In addition, orbital selective Mott phase characteristics develop with doping, with only oneWannier orbital receiving the hole carriers while the other remains half-filled. Lastly, these results suggest that the analysis of models for iron-based two-leg ladders could clarify the origin of pairing tendencies and other exotic properties of iron-based high-critical-temperature superconductors in general.« less

30 CFR 75.800 - High-voltage circuits; circuit breakers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... shall be equipped with devices to provide protection against under-voltage grounded phase, short circuit... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 75.800... § 75.800 High-voltage circuits; circuit breakers. [Statutory Provisions] High-voltage circuits entering...

From circuits to behaviour in the amygdala

PubMed Central

Janak, Patricia H.; Tye, Kay M.

2015-01-01

The amygdala has long been associated with emotion and motivation, playing an essential part in processing both fearful and rewarding environmental stimuli. How can a single structure be crucial for such different functions? With recent technological advances that allow for causal investigations of specific neural circuit elements, we can now begin to map the complex anatomical connections of the amygdala onto behavioural function. Understanding how the amygdala contributes to a wide array of behaviours requires the study of distinct amygdala circuits. PMID:25592533

Characterization of silicon-gate CMOS/SOS integrated circuits processed with ion implantation

NASA Technical Reports Server (NTRS)

Woo, D. S.

1980-01-01

The double layer metallization technology applied on p type silicon gate CMOS/SOS integrated circuits is described. A smooth metal surface was obtained by using the 2% Si-sputtered Al. More than 10% probe yield was achieved on solar cell controller circuit TCS136 (or MSFC-SC101). Reliability tests were performed on 15 arrays at 150 C. Only three arrays failed during the burn in, and 18 arrays out of 22 functioning arrays maintained the leakage current below 100 milli-A. Analysis indicates that this technology will be a viable process if the metal short circuit problem between the two metals can be reduced.

Novel Quaternary Quantum Decoder, Multiplexer and Demultiplexer Circuits

NASA Astrophysics Data System (ADS)

Haghparast, Majid; Monfared, Asma Taheri

2017-05-01

Multiple valued logic is a promising approach to reduce the width of the reversible or quantum circuits, moreover, quaternary logic is considered as being a good choice for future quantum computing technology hence it is very suitable for the encoded realization of binary logic functions through its grouping of 2-bits together into quaternary values. The Quaternary decoder, multiplexer, and demultiplexer are essential units of quaternary digital systems. In this paper, we have initially designed a quantum realization of the quaternary decoder circuit using quaternary 1-qudit gates and quaternary Muthukrishnan-Stroud gates. Then we have presented quantum realization of quaternary multiplexer and demultiplexer circuits using the constructed quaternary decoder circuit and quaternary controlled Feynman gates. The suggested circuits in this paper have a lower quantum cost and hardware complexity than the existing designs that are currently used in quaternary digital systems. All the scales applied in this paper are based on Nanometric area.

Radiation damage in MOS integrated circuits, Part 1

NASA Technical Reports Server (NTRS)

Danchenko, V.

1971-01-01

Complementary and p-channel MOS integrated circuits made by four commercial manufacturers were investigated for sensitivity to radiation environment. The circuits were irradiated with 1.5 MeV electrons. The results are given for electrons and for the Co-60 gamma radiation equivalent. The data are presented in terms of shifts in the threshold potentials and changes in transconductances and leakages. Gate biases of -10V, +10V and zero volts were applied to individual MOS units during irradiation. It was found that, in most of circuits of complementary MOS technologies, noticable changes due to radiation appear first as increased leakage in n-channel MOSFETs somewhat before a total integrated dose 10 to the 12th power electrons/sg cm is reached. The inability of p-channel MOSFETs to turn on sets in at about 10 to the 13th power electrons/sq cm. Of the circuits tested, an RCA A-series circuit was the most radiation resistant sample.

An e-Learning System with MR for Experiments Involving Circuit Construction to Control a Robot

ERIC Educational Resources Information Center

Takemura, Atsushi

2016-01-01

This paper proposes a novel e-Learning system for technological experiments involving electronic circuit-construction and controlling robot motion that are necessary in the field of technology. The proposed system performs automated recognition of circuit images transmitted from individual learners and automatically supplies the learner with…

Influence of seasonal, diel, lunar, and other environmental factors on upstream fish passage in the igarapava fish ladder, Brazil

USGS Publications Warehouse

Bizzotto, P.M.; Godinho, Alexandre L.; Vono, V.; Kynard, B.; Godinho, Hugo P.

2009-01-01

Upstream fish passage was evaluated during 12 months in the vertical-slot Igarapava Fish Ladder constructed around Igarapava Dam, in the heavily dammed Grande River, Southeast Brazil. A video monitoring system was used to observe 61,621 fish that passed the ladder, of which 93.5% were identified to 15 taxa. Among the migratory species, the most abundant were Pimelodus maculatus (33.6% of all fish), Leporinus octofasciatus (31.4%), Leporinus friderici (4.5%), and Prochilodus lineatus (3.1%). Seven taxa were classified as nonmigratory, and of these taxa, the small Bryconamericus stramineus was the most abundant (12.7%) of all fishes. Passage of the 'nonmigratory' taxa upstream in the ladder shows they are migratory in this system and have a strong behavioural drive to move to upstream habitat. Passage of most taxa had a strong seasonal pattern. While some species passed primarily during the day, others showed a distinct nocturnal pattern. Lunar phase and water temperature also strongly affected passage of some taxa. Rainfall and dam discharge had a small or null influence on most taxa; perhaps due to the fairly small catchment area of the reservoir and the highly regulated discharge at Igarapava Dam. ?? 2009 John Wiley & Sons A/S.

A multiply-add engine with monolithically integrated 3D memristor crossbar/CMOS hybrid circuit.

PubMed

Chakrabarti, B; Lastras-Montaño, M A; Adam, G; Prezioso, M; Hoskins, B; Payvand, M; Madhavan, A; Ghofrani, A; Theogarajan, L; Cheng, K-T; Strukov, D B

2017-02-14

Silicon (Si) based complementary metal-oxide semiconductor (CMOS) technology has been the driving force of the information-technology revolution. However, scaling of CMOS technology as per Moore's law has reached a serious bottleneck. Among the emerging technologies memristive devices can be promising for both memory as well as computing applications. Hybrid CMOS/memristor circuits with CMOL (CMOS + "Molecular") architecture have been proposed to combine the extremely high density of the memristive devices with the robustness of CMOS technology, leading to terabit-scale memory and extremely efficient computing paradigm. In this work, we demonstrate a hybrid 3D CMOL circuit with 2 layers of memristive crossbars monolithically integrated on a pre-fabricated CMOS substrate. The integrated crossbars can be fully operated through the underlying CMOS circuitry. The memristive devices in both layers exhibit analog switching behavior with controlled tunability and stable multi-level operation. We perform dot-product operations with the 2D and 3D memristive crossbars to demonstrate the applicability of such 3D CMOL hybrid circuits as a multiply-add engine. To the best of our knowledge this is the first demonstration of a functional 3D CMOL hybrid circuit.

A multiply-add engine with monolithically integrated 3D memristor crossbar/CMOS hybrid circuit

PubMed Central

Chakrabarti, B.; Lastras-Montaño, M. A.; Adam, G.; Prezioso, M.; Hoskins, B.; Cheng, K.-T.; Strukov, D. B.

2017-01-01

Silicon (Si) based complementary metal-oxide semiconductor (CMOS) technology has been the driving force of the information-technology revolution. However, scaling of CMOS technology as per Moore’s law has reached a serious bottleneck. Among the emerging technologies memristive devices can be promising for both memory as well as computing applications. Hybrid CMOS/memristor circuits with CMOL (CMOS + “Molecular”) architecture have been proposed to combine the extremely high density of the memristive devices with the robustness of CMOS technology, leading to terabit-scale memory and extremely efficient computing paradigm. In this work, we demonstrate a hybrid 3D CMOL circuit with 2 layers of memristive crossbars monolithically integrated on a pre-fabricated CMOS substrate. The integrated crossbars can be fully operated through the underlying CMOS circuitry. The memristive devices in both layers exhibit analog switching behavior with controlled tunability and stable multi-level operation. We perform dot-product operations with the 2D and 3D memristive crossbars to demonstrate the applicability of such 3D CMOL hybrid circuits as a multiply-add engine. To the best of our knowledge this is the first demonstration of a functional 3D CMOL hybrid circuit. PMID:28195239

Measuring circuit

DOEpatents

Sun, Shan C.; Chaprnka, Anthony G.

1977-01-11

An automatic gain control circuit functions to adjust the magnitude of an input signal supplied to a measuring circuit to a level within the dynamic range of the measuring circuit while a log-ratio circuit adjusts the magnitude of the output signal from the measuring circuit to the level of the input signal and optimizes the signal-to-noise ratio performance of the measuring circuit.

HST/WFC3 flux calibration ladder: Vega

NASA Astrophysics Data System (ADS)

Deustua, Susana E.; Bohlin, Ralph; Pirzkal, Nor; MacKenty, John

2014-08-01

Vega is one of only a few stars calibrated against an SI-traceable blackbody, and is the historical flux standard. Photometric zeropoints of the Hubble Space Telescope's instruments rely on Vega, through the transfer of its calibration via stellar atmosphere models to the suite of standard stars. HST's recently implemented scan mode has enabled us to develop a path to an absolute SI traceable calibration for HST IR observations. To fill in the crucial gap between 0.9 and 1.7 micron in the absolute calibration, we acquired -1st order spectra of Vega with the two WFC3 infrared grisms. At the same time, we have improved the calibration of the -1st orders of both WFC3 IR grisms, as well as extended the dynamic range of WFC3 science observations by a factor of 10000. We describe our progress to date on the WFC3 `flux calibration ladder' project to provide currently needed accurate zeropoint measurements in the IR

Study of CMOS-SOI Integrated Temperature Sensing Circuits for On-Chip Temperature Monitoring.

PubMed

Malits, Maria; Brouk, Igor; Nemirovsky, Yael

2018-05-19

This paper investigates the concepts, performance and limitations of temperature sensing circuits realized in complementary metal-oxide-semiconductor (CMOS) silicon on insulator (SOI) technology. It is shown that the MOSFET threshold voltage ( V t ) can be used to accurately measure the chip local temperature by using a V t extractor circuit. Furthermore, the circuit's performance is compared to standard circuits used to generate an accurate output current or voltage proportional to the absolute temperature, i.e., proportional-to-absolute temperature (PTAT), in terms of linearity, sensitivity, power consumption, speed, accuracy and calibration needs. It is shown that the V t extractor circuit is a better solution to determine the temperature of low power, analog and mixed-signal designs due to its accuracy, low power consumption and no need for calibration. The circuit has been designed using 1 µm partially depleted (PD) CMOS-SOI technology, and demonstrates a measurement inaccuracy of ±1.5 K across 300 K⁻500 K temperature range while consuming only 30 µW during operation.

Fast frequency divider circuit using combinational logic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helinski, Ryan

The various technologies presented herein relate to performing on-chip frequency division of an operating frequency of a ring oscillator (RO). Per the various embodiments herein, a conflict between RO size versus operational frequency can be addressed by dividing the output frequency of the RO to a frequency that can be measured on-chip. A frequency divider circuit (comprising NOR gates and latches, for example) can be utilized in conjunction with the RO on the chip. In an embodiment, the frequency divider circuit can include a pair of latches coupled to the RO to facilitate dividing the oscillating frequency of the ROmore » by 2. In another embodiment, the frequency divider circuit can include four latches (operating in pairs) coupled to the RO to facilitate dividing the oscillating frequency of the RO by 4. A plurality of ROs can be MUXed to the plurality of ROs by a single oscillation-counting circuit.« less

Integrated logic circuits using single-atom transistors

PubMed Central

Mol, J. A.; Verduijn, J.; Levine, R. D.; Remacle, F.

2011-01-01

Scaling down the size of computing circuits is about to reach the limitations imposed by the discrete atomic structure of matter. Reducing the power requirements and thereby dissipation of integrated circuits is also essential. New paradigms are needed to sustain the rate of progress that society has become used to. Single-atom transistors, SATs, cascaded in a circuit are proposed as a promising route that is compatible with existing technology. We demonstrate the use of quantum degrees of freedom to perform logic operations in a complementary-metal–oxide–semiconductor device. Each SAT performs multilevel logic by electrically addressing the electronic states of a dopant atom. A single electron transistor decodes the physical multivalued output into the conventional binary output. A robust scalable circuit of two concatenated full adders is reported, where by utilizing charge and quantum degrees of freedom, the functionality of the transistor is pushed far beyond that of a simple switch. PMID:21808050

Telecommunications Systems Career Ladder, AFSC 307XO.

DTIC Science & Technology

1981-01-01

standard test tone levels perform impulse noise tests make in-service or out-of- service quality check.s on composite signal transmission levels Even...service or out-of- service quality control (QC) reports maintain trouble and restoration record forms (DD Form 1443) direct circuit or system checks...include: perform fault isolation on analog circuits make in-service or out-of- service quality checks on voice frequency carrier telegraph (VFCT) terminals

Advanced Packaging for VLSI/VHSIC (Very Large Scale Integrated Circuits/Very High Speed Integrated Circuits) Applications: Electrical, Thermal, and Mechanical Considerations - An IR&D Report.

DTIC Science & Technology

1987-11-01

developed that can be used by circuit engineers to extract the maximum performance from the devices on various board technologies including multilayer ceramic...Design guidelines have been developed that can be used by circuit engineers to extract the maxi- mum performance from the devices on various board...25 Attenuation and Dispersion Effects ......................................... 27 Skin Effect

Nucleic acids for the rational design of reaction circuits.

PubMed

Padirac, Adrien; Fujii, Teruo; Rondelez, Yannick

2013-08-01

Nucleic acid-based circuits are rationally designed in vitro assemblies that can perform complex preencoded programs. They can be used to mimic in silico computations. Recent works emphasized the modularity and robustness of these circuits, which allow their scaling-up. Another new development has led to dynamic, time-responsive systems that can display emergent behaviors like oscillations. These are closely related to biological architectures and provide an in vitro model of in vivo information processing. Nucleic acid circuits have already been used to handle various processes for technological or biotechnological purposes. Future applications of these chemical smart systems will benefit from the rapidly growing ability to design, construct, and model nucleic acid circuits of increasing size. Copyright © 2012 Elsevier Ltd. All rights reserved.

30 CFR 77.800 - High-voltage circuits; circuit breakers.

Code of Federal Regulations, 2010 CFR

2010-07-01

... devices to provide protection against under voltage, grounded phase, short circuit and overcurrent. High... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 77.800... COAL MINES Surface High-Voltage Distribution § 77.800 High-voltage circuits; circuit breakers. High...

Development and validation of a nursing professionalism evaluation model in a career ladder system.

PubMed

Kim, Yeon Hee; Jung, Young Sun; Min, Ja; Song, Eun Young; Ok, Jung Hui; Lim, Changwon; Kim, Kyunghee; Kim, Ji-Su

2017-01-01

The clinical ladder system categorizes the degree of nursing professionalism and rewards and is an important human resource tool for managing nursing. We developed a model to evaluate nursing professionalism, which determines the clinical ladder system levels, and verified its validity. Data were collected using a clinical competence tool developed in this study, and existing methods such as the nursing professionalism evaluation tool, peer reviews, and face-to-face interviews to evaluate promotions and verify the presented content in a medical institution. Reliability and convergent and discriminant validity of the clinical competence evaluation tool were verified using SmartPLS software. The validity of the model for evaluating overall nursing professionalism was also analyzed. Clinical competence was determined by five dimensions of nursing practice: scientific, technical, ethical, aesthetic, and existential. The structural model explained 66% of the variance. Clinical competence scales, peer reviews, and face-to-face interviews directly determined nursing professionalism levels. The evaluation system can be used for evaluating nurses' professionalism in actual medical institutions from a nursing practice perspective. A conceptual framework for establishing a human resources management system for nurses and a tool for evaluating nursing professionalism at medical institutions is provided.

Ultra-wideband ladder filter using SH(0) plate wave in thin LiNbO(3) plate and its application to tunable filter.

PubMed

Kadota, Michio; Tanaka, Shuji

2015-05-01

A cognitive radio terminal using vacant frequency bands of digital TV (DTV) channels, i.e., TV white space, strongly requires a compact tunable filter covering a wide frequency range of the DTV band (470 to 710 MHz in Japan). In this study, a T-type ladder filter using ultra-wideband shear horizontal mode plate wave resonators was fabricated, and a low peak insertion loss of 0.8 dB and an ultra-large 6 dB bandwidth of 240 MHz (41%) were measured in the DTV band. In addition, bandpass filters with different center frequencies of 502 and 653 MHz at 6 dB attenuation were numerically synthesized based on the same T-type ladder filter in conjunction with band rejection filters with different frequencies. The results suggest that the combination of the wideband T-type ladder filter and the band rejection filters connected with variable capacitors enables a tunable filter with large tunability of frequency and bandwidth as well as large rejection at the adjacent channels of an available TV white space.

Project Circuits in a Basic Electric Circuits Course

ERIC Educational Resources Information Center

Becker, James P.; Plumb, Carolyn; Revia, Richard A.

2014-01-01

The use of project circuits (a photoplethysmograph circuit and a simple audio amplifier), introduced in a sophomore-level electric circuits course utilizing active learning and inquiry-based methods, is described. The development of the project circuits was initiated to promote enhanced engagement and deeper understanding of course content among…

Static holes in the geometrically frustrated bow-tie ladder

NASA Astrophysics Data System (ADS)

Martins, George B.; Brenig, Wolfram

2008-10-01

We investigate the doping of a geometrically frustrated spin ladder with static holes by a complementary approach using exact diagonalization and quantum dimers. Results for thermodynamic properties, the singlet density of states, the hole-binding energy and the spin correlations will be presented. For the undoped systems the ground state is non-degenerate, with translationally invariant nearest-neighbor spin correlations. For the doped case, we find that static holes polarize their vicinity through a localization of singlets, reducing the frustration. This polarization induces short range repulsive forces between two holes and an oscillatory behavior of the long range two-hole energy. For most quantities investigated, we find very good agreement between the quantum dimer approach and the results from exact diagonalization.

Quantum-circuit refrigerator

NASA Astrophysics Data System (ADS)

Tan, Kuan Yen; Partanen, Matti; Lake, Russell E.; Govenius, Joonas; Masuda, Shumpei; Möttönen, Mikko

2017-05-01

Quantum technology promises revolutionizing applications in information processing, communications, sensing and modelling. However, efficient on-demand cooling of the functional quantum degrees of freedom remains challenging in many solid-state implementations, such as superconducting circuits. Here we demonstrate direct cooling of a superconducting resonator mode using voltage-controllable electron tunnelling in a nanoscale refrigerator. This result is revealed by a decreased electron temperature at a resonator-coupled probe resistor, even for an elevated electron temperature at the refrigerator. Our conclusions are verified by control experiments and by a good quantitative agreement between theory and experimental observations at various operation voltages and bath temperatures. In the future, we aim to remove spurious dissipation introduced by our refrigerator and to decrease the operational temperature. Such an ideal quantum-circuit refrigerator has potential applications in the initialization of quantum electric devices. In the superconducting quantum computer, for example, fast and accurate reset of the quantum memory is needed.

Symmetry-broken states in a system of interacting bosons on a two-leg ladder with a uniform Abelian gauge field

NASA Astrophysics Data System (ADS)

Greschner, S.; Piraud, M.; Heidrich-Meisner, F.; McCulloch, I. P.; Schollwöck, U.; Vekua, T.

2016-12-01

We study the quantum phases of bosons with repulsive contact interactions on a two-leg ladder in the presence of a uniform Abelian gauge field. The model realizes many interesting states, including Meissner phases, vortex fluids, vortex lattices, charge density waves, and the biased-ladder phase. Our work focuses on the subset of these states that breaks a discrete symmetry. We use density matrix renormalization group simulations to demonstrate the existence of three vortex-lattice states at different vortex densities and we characterize the phase transitions from these phases into neighboring states. Furthermore, we provide an intuitive explanation of the chiral-current reversal effect that is tied to some of these vortex lattices. We also study a charge-density-wave state that exists at 1/4 particle filling at large interaction strengths and flux values close to half a flux quantum. By changing the system parameters, this state can transition into a completely gapped vortex-lattice Mott-insulating state. We elucidate the stability of these phases against nearest-neighbor interactions on the rungs of the ladder relevant for experimental realizations with a synthetic lattice dimension. A charge-density-wave state at 1/3 particle filling can be stabilized for flux values close to half a flux quantum and for very strong on-site interactions in the presence of strong repulsion on the rungs. Finally, we analytically describe the emergence of these phases in the low-density regime, and, in particular, we obtain the boundaries of the biased-ladder phase, i.e., the phase that features a density imbalance between the legs. We make contact with recent quantum-gas experiments that realized related models and discuss signatures of these quantum states in experimentally accessible observables.

High accuracy digital aging monitor based on PLL-VCO circuit

NASA Astrophysics Data System (ADS)

Yuejun, Zhang; Zhidi, Jiang; Pengjun, Wang; Xuelong, Zhang

2015-01-01

As the manufacturing process is scaled down to the nanoscale, the aging phenomenon significantly affects the reliability and lifetime of integrated circuits. Consequently, the precise measurement of digital CMOS aging is a key aspect of nanoscale aging tolerant circuit design. This paper proposes a high accuracy digital aging monitor using phase-locked loop and voltage-controlled oscillator (PLL-VCO) circuit. The proposed monitor eliminates the circuit self-aging effect for the characteristic of PLL, whose frequency has no relationship with circuit aging phenomenon. The PLL-VCO monitor is implemented in TSMC low power 65 nm CMOS technology, and its area occupies 303.28 × 298.94 μm2. After accelerating aging tests, the experimental results show that PLL-VCO monitor improves accuracy about high temperature by 2.4% and high voltage by 18.7%.

Using a familiar risk comparison within a risk ladder to improve risk understanding by low numerates: a study of visual attention.

PubMed

Keller, Carmen

2011-07-01

Previous experimental research provides evidence that a familiar risk comparison within a risk ladder is understood by low- and high-numerate individuals. It especially helps low numerates to better evaluate risk. In the present study, an eye tracker was used to capture individuals' visual attention to a familiar risk comparison, such as the risk associated with smoking. Two parameters of information processing-efficiency and level-were derived from visual attention. A random sample of participants from the general population (N= 68) interpreted a given risk level with the help of the risk ladder. Numeracy was negatively correlated with overall visual attention on the risk ladder (r(s) =-0.28, p= 0.01), indicating that the lower the numeracy, the more the time spent looking at the whole risk ladder. Numeracy was positively correlated with the efficiency of processing relevant frequency (r(s) = 0.34, p < 0.001) and relevant textual information (r(s) = 0.34, p < 0.001), but not with the efficiency of processing relevant comparative information and numerical information. There was a significant negative correlation between numeracy and the level of processing of relevant comparative risk information (r(s) =-0.21, p < 0.01), indicating that low numerates processed the comparative risk information more deeply than the high numerates. There was no correlation between numeracy and perceived risk. These results add to previous experimental research, indicating that the smoking risk comparison was crucial for low numerates to evaluate and understand risk. Furthermore, the eye-tracker method is promising for studying information processing and improving risk communication formats. © 2011 Society for Risk Analysis.

Optimized structural designs for stretchable silicon integrated circuits.

PubMed

Kim, Dae-Hyeong; Liu, Zhuangjian; Kim, Yun-Soung; Wu, Jian; Song, Jizhou; Kim, Hoon-Sik; Huang, Yonggang; Hwang, Keh-Chih; Zhang, Yongwei; Rogers, John A

2009-12-01

Materials and design strategies for stretchable silicon integrated circuits that use non-coplanar mesh layouts and elastomeric substrates are presented. Detailed experimental and theoretical studies reveal many of the key underlying aspects of these systems. The results shpw, as an example, optimized mechanics and materials for circuits that exhibit maximum principal strains less than 0.2% even for applied strains of up to approximately 90%. Simple circuits, including complementary metal-oxide-semiconductor inverters and n-type metal-oxide-semiconductor differential amplifiers, validate these designs. The results suggest practical routes to high-performance electronics with linear elastic responses to large strain deformations, suitable for diverse applications that are not readily addressed with conventional wafer-based technologies.

Radiation Testing and Evaluation Issues for Modern Integrated Circuits

NASA Technical Reports Server (NTRS)

LaBel, Kenneth A.; Cohn, Lew M.

2005-01-01

Abstract. Changes in modern integrated circuit (IC) technologies have modified the way we approach and conduct radiation tolerance and testing of electronics. These changes include scaling of geometries, new materials, new packaging technologies, and overall speed and device complexity challenges. In this short course section, we will identify and discuss these issues as they impact radiation testing, modeling, and effects mitigation of modern integrated circuits. The focus will be on CMOS-based technologies, however, other high performance technologies will be discussed where appropriate. The effects of concern will be: Single-Event Effects (SEE) and steady state total ionizing dose (TID) IC response. However, due to the growing use of opto-electronics in space systems issues concerning displacement damage testing will also be considered. This short course section is not intended to provide detailed "how-to-test" information, but simply provide a snapshot of current challenges and some of the approaches being considered.

South Dakota Statewide Core Curriculum, Career Ladder and Challenge System: Volumes I and II. Final Report.

ERIC Educational Resources Information Center

1975

The two volume final report of the South Dakota Statewide Core Curriculum, Career Ladder, and Challenge System Project, coordinating associated health and nursing education on a statewide basis to achieve a more systematic production and utilization of health manpower, is presented. Volume 1 includes five chapters: (1) and (2) outlining funding…

Hidden Order and Symmetry Protected Topological States in Quantum Link Ladders

NASA Astrophysics Data System (ADS)

Cardarelli, L.; Greschner, S.; Santos, L.

2017-11-01

We show that, whereas spin-1 /2 one-dimensional U(1) quantum-link models (QLMs) are topologically trivial, when implemented in ladderlike lattices these models may present an intriguing ground-state phase diagram, which includes a symmetry protected topological (SPT) phase that may be readily revealed by analyzing long-range string spin correlations along the ladder legs. We propose a simple scheme for the realization of spin-1 /2 U(1) QLMs based on single-component fermions loaded in an optical lattice with s and p bands, showing that the SPT phase may be experimentally realized by adiabatic preparation.

Relay Protection and Automation Systems Based on Programmable Logic Integrated Circuits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lashin, A. V., E-mail: LashinAV@lhp.ru; Kozyrev, A. V.

One of the most promising forms of developing the apparatus part of relay protection and automation devices is considered. The advantages of choosing programmable logic integrated circuits to obtain adaptive technological algorithms in power system protection and control systems are pointed out. The technical difficulties in the problems which today stand in the way of using relay protection and automation systems are indicated and a new technology for solving these problems is presented. Particular attention is devoted to the possibility of reconfiguring the logic of these devices, using programmable logic integrated circuits.

Variability-aware double-patterning layout optimization for analog circuits

NASA Astrophysics Data System (ADS)

Li, Yongfu; Perez, Valerio; Tripathi, Vikas; Lee, Zhao Chuan; Tseng, I.-Lun; Ong, Jonathan Yoong Seang

2018-03-01

The semiconductor industry has adopted multi-patterning techniques to manage the delay in the extreme ultraviolet lithography technology. During the design process of double-patterning lithography layout masks, two polygons are assigned to different masks if their spacing is less than the minimum printable spacing. With these additional design constraints, it is very difficult to find experienced layout-design engineers who have a good understanding of the circuit to manually optimize the mask layers in order to minimize color-induced circuit variations. In this work, we investigate the impact of double-patterning lithography on analog circuits and provide quantitative analysis for our designers to select the optimal mask to minimize the circuit's mismatch. To overcome the problem and improve the turn-around time, we proposed our smart "anchoring" placement technique to optimize mask decomposition for analog circuits. We have developed a software prototype that is capable of providing anchoring markers in the layout, allowing industry standard tools to perform automated color decomposition process.

Competency-Based Curriculum Guide for Laser Technology. September 1980-June 1981.

ERIC Educational Resources Information Center

Fioroni, John J.

This document contains materials developed by a project to provide a competency-based curriculum guide for laser technology at the community college level. An abstract of the final report is included. Next, the 17 job competencies determined as necessary to meet the job description of laser technician are listed. A career ladder and qualifications…

Removal of Gross Air Embolization from Cardiopulmonary Bypass Circuits with Integrated Arterial Line Filters: A Comparison of Circuit Designs.

PubMed

Reagor, James A; Holt, David W

2016-03-01

Advances in technology, the desire to minimize blood product transfusions, and concerns relating to inflammatory mediators have lead many practitioners and manufacturers to minimize cardiopulmonary bypass (CBP) circuit designs. The oxygenator and arterial line filter (ALF) have been integrated into one device as a method of attaining a reduction in prime volume and surface area. The instructions for use of a currently available oxygenator with integrated ALF recommends incorporating a recirculation line distal to the oxygenator. However, according to an unscientific survey, 70% of respondents utilize CPB circuits incorporating integrated ALFs without a path of recirculation distal to the oxygenator outlet. Considering this circuit design, the ability to quickly remove a gross air bolus in the blood path distal to the oxygenator may be compromised. This in vitro study was designed to determine if the time required to remove a gross air bolus from a CPB circuit without a path of recirculation distal to the oxygenator will be significantly longer than that of a circuit with a path of recirculation distal to the oxygenator. A significant difference was found in the mean time required to remove a gross air bolus between the circuit designs (p = .0003). Additionally, There was found to be a statistically significant difference in the mean time required to remove a gross air bolus between Trial 1 and Trials 4 (p = .015) and 5 (p =.014) irrespective of the circuit design. Under the parameters of this study, a recirculation line distal to an oxygenator with an integrated ALF significantly decreases the time it takes to remove an air bolus from the CPB circuit and may be safer for clinical use than the same circuit without a recirculation line.

Compensated gain control circuit for buck regulator command charge circuit

DOEpatents

Barrett, David M.

1996-01-01

A buck regulator command charge circuit includes a compensated-gain control signal for compensating for changes in the component values in order to achieve optimal voltage regulation. The compensated-gain control circuit includes an automatic-gain control circuit for generating a variable-gain control signal. The automatic-gain control circuit is formed of a precision rectifier circuit, a filter network, an error amplifier, and an integrator circuit.

Unbalanced neuronal circuits in addiction.

PubMed

Volkow, Nora D; Wang, Gen-Jack; Tomasi, Dardo; Baler, Ruben D

2013-08-01

Through sequential waves of drug-induced neurochemical stimulation, addiction co-opts the brain's neuronal circuits that mediate reward, motivation to behavioral inflexibility and a severe disruption of self-control and compulsive drug intake. Brain imaging technologies have allowed neuroscientists to map out the neural landscape of addiction in the human brain and to understand how drugs modify it. Published by Elsevier Ltd.

Studies toward brevisulcenal F via convergent strategies for marine ladder polyether synthesis.

PubMed

Katcher, Matthew; Jamison, Timothy F

2018-03-15

Shortly after the initial isolation of marine ladder polyether natural products, biomimetic epoxide-opening cascade reactions were proposed as an efficient strategy for the synthesis of these compounds. However, difficulties in assembling the cascade precursors have limited the realization of these cascades. In this report, we describe strategies that provide convergent access to cascade precursors via regioselective allylation and efficient fragment coupling. We then investigate epoxide-opening cascades promoted by strong bases for the formation of fused tetrahydropyrans. These strategies are evaluated in the context of the synthesis of rings CDEFG of brevisulcenal F.

Microelectromechanical accelerometer with resonance-cancelling control circuit including an idle state

DOEpatents

Chu, Dahlon D.; Thelen, Jr., Donald C.; Campbell, David V.

2001-01-01

A digital feedback control circuit is disclosed for use in an accelerometer (e.g. a microelectromechanical accelerometer). The digital feedback control circuit, which periodically re-centers a proof mass in response to a sensed acceleration, is based on a sigma-delta (.SIGMA..DELTA.) configuration that includes a notch filter (e.g. a digital switched-capacitor filter) for rejecting signals due to mechanical resonances of the proof mass and further includes a comparator (e.g. a three-level comparator). The comparator generates one of three possible feedback states, with two of the feedback states acting to re-center the proof mass when that is needed, and with a third feedback state being an "idle" state which does not act to move the proof mass when no re-centering is needed. Additionally, the digital feedback control system includes an auto-zero trim capability for calibration of the accelerometer for accurate sensing of acceleration. The digital feedback control circuit can be fabricated using complementary metal-oxide semiconductor (CMOS) technology, bi-CMOS technology or bipolar technology and used in single- and dual-proof-mass accelerometers.

Compensated gain control circuit for buck regulator command charge circuit

DOEpatents

Barrett, D.M.

1996-11-05

A buck regulator command charge circuit includes a compensated-gain control signal for compensating for changes in the component values in order to achieve optimal voltage regulation. The compensated-gain control circuit includes an automatic-gain control circuit for generating a variable-gain control signal. The automatic-gain control circuit is formed of a precision rectifier circuit, a filter network, an error amplifier, and an integrator circuit. 5 figs.

Interplay of magnetism and superconductivity in the compressed Fe-ladder compound BaFe 2 Se 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ying, Jianjun; Lei, Hechang; Petrovic, Cedomir

High pressure resistance, susceptibility, and Fe K β x-ray emission spectroscopy measurements were performed on Fe-ladder compound BaFe 2 Se 3 . Pressure-induced superconductivity was observed which is similar to the previously reported superconductivity in the BaFe 2 S 3 samples. The slope of local magnetic moment versus pressure shows an anomaly across the insulator-metal transition pressure in the BaFe 2 Se 3 samples. The local magnetic moment is continuously decreasing with increasing pressure, and the superconductivity appears only when the local magnetic moment value is comparable to the one in the iron-pnictide superconductors. Our results indicate that the compressedmore » BaFe 2 C h 3 ( C h = S , Se) is a new family of iron-based superconductors. Despite the crystal structures completely different from the known iron-based superconducting materials, the magnetism in this Fe-ladder material plays a critical role in superconductivity. This behavior is similar to the other members of iron-based superconducting materials.« less

Driven superconducting quantum circuits

NASA Astrophysics Data System (ADS)

Nakamura, Yasunobu

2014-03-01

Driven nonlinear quantum systems show rich phenomena in various fields of physics. Among them, superconducting quantum circuits have very attractive features such as well-controlled quantum states with design flexibility, strong nonlinearity of Josephson junctions, strong coupling to electromagnetic driving fields, little internal dissipation, and tailored coupling to the electromagnetic environment. We have investigated properties and functionalities of driven superconducting quantum circuits. A transmon qubit coupled to a transmission line shows nearly perfect spatial mode matching between the incident and scattered microwave field in the 1D mode. Dressed states under a driving field are studied there and also in a semi-infinite 1D mode terminated by a resonator containing a flux qubit. An effective Λ-type three-level system is realized under an appropriate driving condition. It allows ``impedance-matched'' perfect absorption of incident probe photons and down conversion into another frequency mode. Finally, the weak signal from the qubit is read out using a Josephson parametric amplifier/oscillator which is another nonlinear circuit driven by a strong pump field. This work was partly supported by the Funding Program for World-Leading Innovative R&D on Science and Technology (FIRST), Project for Developing Innovation Systems of MEXT, MEXT KAKENHI ``Quantum Cybernetics,'' and the NICT Commissioned Research.

Synthetic Gene Expression Circuits for Designing Precision Tools in Oncology

PubMed Central

Re, Angela

2017-01-01

Precision medicine in oncology needs to enhance its capabilities to match diagnostic and therapeutic technologies to individual patients. Synthetic biology streamlines the design and construction of functionalized devices through standardization and rational engineering of basic biological elements decoupled from their natural context. Remarkable improvements have opened the prospects for the availability of synthetic devices of enhanced mechanism clarity, robustness, sensitivity, as well as scalability and portability, which might bring new capabilities in precision cancer medicine implementations. In this review, we begin by presenting a brief overview of some of the major advances in the engineering of synthetic genetic circuits aimed to the control of gene expression and operating at the transcriptional, post-transcriptional/translational, and post-translational levels. We then focus on engineering synthetic circuits as an enabling methodology for the successful establishment of precision technologies in oncology. We describe significant advancements in our capabilities to tailor synthetic genetic circuits to specific applications in tumor diagnosis, tumor cell- and gene-based therapy, and drug delivery. PMID:28894736

Implementability of two-qubit unitary operations over the butterfly network and the ladder network with free classical communication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akibue, Seiseki; Murao, Mio

2014-12-04

We investigate distributed implementation of two-qubit unitary operations over two primitive networks, the butterfly network and the ladder network, as a first step to apply network coding for quantum computation. By classifying two-qubit unitary operations in terms of the Kraus-Cirac number, the number of non-zero parameters describing the global part of two-qubit unitary operations, we analyze which class of two-qubit unitary operations is implementable over these networks with free classical communication. For the butterfly network, we show that two classes of two-qubit unitary operations, which contain all Clifford, controlled-unitary and matchgate operations, are implementable over the network. For the laddermore » network, we show that two-qubit unitary operations are implementable over the network if and only if their Kraus-Cirac number do not exceed the number of the bridges of the ladder.« less

Selective Processing Techniques for Electronics and Opto-Electronic Applications: Quantum-Well Devices and Integrated Optic Circuits

DTIC Science & Technology

1993-02-10

new technology is to have sufficient control of processing to *- describable by an appropriate elecromagnetic model . build useful devices. For example...3. W aveguide Modulators .................................. 7 B. Integrated Optical Device and Circuit Modeling ... ................... .. 10 C...following categories: A. Integrated Optical Devices and Technology B. Integrated Optical Device and Circuit Modeling C. Cryogenic Etching for Low

Laboratory experiments in integrated circuit fabrication

NASA Technical Reports Server (NTRS)

Jenkins, Thomas J.; Kolesar, Edward S.

1993-01-01

The objectives of the experiment are fourfold: to provide practical experience implementing the fundamental processes and technology associated with the science and art of integrated circuit (IC) fabrication; to afford the opportunity for the student to apply the theory associated with IC fabrication and semiconductor device operation; to motivate the student to exercise engineering decisions associated with fabricating integrated circuits; and to complement the theory of n-channel MOS and diffused devices that are presented in the classroom by actually fabricating and testing them. Therefore, a balance between theory and practice can be realized in the education of young engineers, whose education is often criticized as lacking sufficient design and practical content.

HRD--Leadership Training for Women on the Lower Rungs of the Organizational Ladder: A Qualitative Study

ERIC Educational Resources Information Center

Dugan, Dixie

2010-01-01

The purpose of this case study, HRD--Leadership Training for Women on the Lower Rungs of the Organizational Ladder: A Qualitative Study, was to determine the responses of a group of women to a series of classes on leadership development and to perceive what they might have gained from this experience. These classes were modeled after those offered…

Magneto-optical polarization rotation in a ladder-type atomic system for tunable offset locking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parniak, Michał, E-mail: michal.parniak@fuw.edu.pl; Leszczyński, Adam; Wasilewski, Wojciech

2016-04-18

We demonstrate an easily tunable locking scheme for stabilizing frequency-sum of two lasers on a two-photon ladder transition based on polarization rotation in warm rubidium vapors induced by magnetic field and circularly polarized drive field. Unprecedented tunability of the two-photon offset frequency is due to strong splitting and shifting of magnetic states in external field. In our experimental setup, we achieve two-photon detuning of up to 700 MHz.

A millimeter-wave tunneladder TWT

NASA Technical Reports Server (NTRS)

Wilson, D.

1988-01-01

A millimeter-wave traveling wave tube (TWT) was developed using a dispersive, high-impedance forward wave interaction structure based on a ladder, with non-space-harmonic interaction, for a tube with high gain per inch and high efficiency. The 'TunneLadder' interaction structure combines ladder properties modified to accommodate Pierce gun beam optics in a radially magnetized PM focusing structure. The development involved the fabrication of chemically milled, shaped ladders diffusion brazed to diamond cubes which are in turn active diffusion brazed to each ridge of a doubly ridged waveguide. Cold-test data, representing the (omega)(beta) and and impedance characteristics of the modified ladder circuit, were used in small and large-signal computer programs to predict TWT gain and efficiency. The structural design emphasizes ruggedness and reliability. Actual data from tested tubes verify the predicted performance while providing broader bandwidth than expected.

A Study of Career Ladders and Manpower Development for Non-Management Personnel in the Food Service Industry.

ERIC Educational Resources Information Center

State Univ. of New York, Ithaca. School of Hotel Administration at Cornell Univ.

Because of its failure to provide career ladders for non-management employees, the food service industry is facing increasingly severe manpower shortages and labor turnover. Unnecessary requirements bar entry workers from many jobs, and training opportunities leave much to be desired. This report identifies the problem areas and develops a model…

Fundamental energy limits of SET-based Brownian NAND and half-adder circuits. Preliminary findings from a physical-information-theoretic methodology

NASA Astrophysics Data System (ADS)

Ercan, İlke; Suyabatmaz, Enes

2018-06-01

The saturation in the efficiency and performance scaling of conventional electronic technologies brings about the development of novel computational paradigms. Brownian circuits are among the promising alternatives that can exploit fluctuations to increase the efficiency of information processing in nanocomputing. A Brownian cellular automaton, where signals propagate randomly and are driven by local transition rules, can be made computationally universal by embedding arbitrary asynchronous circuits on it. One of the potential realizations of such circuits is via single electron tunneling (SET) devices since SET technology enable simulation of noise and fluctuations in a fashion similar to Brownian search. In this paper, we perform a physical-information-theoretic analysis on the efficiency limitations in a Brownian NAND and half-adder circuits implemented using SET technology. The method we employed here establishes a solid ground that enables studying computational and physical features of this emerging technology on an equal footing, and yield fundamental lower bounds that provide valuable insights into how far its efficiency can be improved in principle. In order to provide a basis for comparison, we also analyze a NAND gate and half-adder circuit implemented in complementary metal oxide semiconductor technology to show how the fundamental bound of the Brownian circuit compares against a conventional paradigm.

Expediting analog design retargeting by design knowledge re-use and circuit synthesis: a practical example on a Delta-Sigma modulator

NASA Astrophysics Data System (ADS)

Webb, Matthew; Tang, Hua

2016-08-01

In the past decade or two, due to constant and rapid technology changes, analog design re-use or design retargeting to newer technologies has been brought to the table in order to expedite the design process and improve time-to-market. If properly conducted, analog design retargeting could significantly cut down design cycle compared to designs starting from the scratch. In this article, we present an empirical and general method for efficient analog design retargeting by design knowledge re-use and circuit synthesis (CS). The method first identifies circuit blocks that compose the source system and extracts the performance parameter specifications of each circuit block. Then, for each circuit block, it scales the values of design variables (DV) from the source design to derive an initial design in the target technology. Depending on the performance of this initial target design, a design space is defined for synthesis. Subsequently, each circuit block is automatically synthesised using state-of-art analog synthesis tools based on a combination of global and local optimisation techniques to achieve comparable performance specifications to those extracted from the source system. Finally, the overall system is composed of those synthesised circuit blocks in the target technology. We illustrate the method using a practical example of a complex Delta-Sigma modulator (DSM) circuit.

Silica Integrated Optical Circuits Based on Glass Photosensitivity

NASA Technical Reports Server (NTRS)

Abushagur, Mustafa A. G.

1999-01-01

Integrated optical circuits play a major rule in the new photonics technology both in communication and sensing due to their small size and compatibility with integrated circuits. Currently integrated optical circuits (IOCs) are fabricated using similar manufacturing to those used in the semiconductor industry. In this study we are considering a new technique to fabricate IOCs which does not require layers of photolithography, depositing and etching. This method is based on the photosensitivity of germanosilicate glasses. Waveguides and other IOC devises can be patterned in these glasses by exposing them using UV lasers. This exposure by UV light changes the index of refraction of the germanosilicate glass. This technique enjoys both the simplicity and flexibility of design and fabrication with also the potential of being fast and low cost.

The design of infrared information collection circuit based on embedded technology

NASA Astrophysics Data System (ADS)

Liu, Haoting; Zhang, Yicong

2013-07-01

S3C2410 processor is a 16/32 bit RISC embedded processor which based on ARM920T core and AMNA bus, and mainly for handheld devices, and high cost, low-power applications. This design introduces a design plan of the PIR sensor system, circuit and its assembling, debugging. The Application Circuit of the passive PIR alarm uses the invisibility of the infrared radiation well into the alarm system, and in order to achieve the anti-theft alarm and security purposes. When the body goes into the range of PIR sensor detection, sensors will detect heat sources and then the sensor will output a weak signal. The Signal should be amplified, compared and delayed; finally light emitting diodes emit light, playing the role of a police alarm.

The power of engagement: implementation of a career ladder program.

PubMed

Bourgeault, Robert; Newmark, Jason

2012-01-01

At Baystate Health in Massachusetts, the development and implementation of a career ladder program was implemented to reduce turnover and to improve employee satisfaction, morale, and recruitment efforts. There was significant initial expenditure in the program, as a result of promoting the large number of employees with significant experience and seniority. A smaller number of staff are expected to apply for advancement during successive cycles, allowing for decreased incremental expense going forward. Critical to the success of the program was understanding the time commitment, getting senior organizational support and staff buy-in, and justifying the associated expenses. The development and initiation of the program has done much to support a positive work environment with increased morale and higher performance among significant numbers of staff at all levels.

A New Test Method of Circuit Breaker Spring Telescopic Characteristics Based Image Processing

NASA Astrophysics Data System (ADS)

Huang, Huimin; Wang, Feifeng; Lu, Yufeng; Xia, Xiaofei; Su, Yi

2018-06-01

This paper applied computer vision technology to the fatigue condition monitoring of springs, and a new telescopic characteristics test method is proposed for circuit breaker operating mechanism spring based on image processing technology. High-speed camera is utilized to capture spring movement image sequences when high voltage circuit breaker operated. Then the image-matching method is used to obtain the deformation-time curve and speed-time curve, and the spring expansion and deformation parameters are extracted from it, which will lay a foundation for subsequent spring force analysis and matching state evaluation. After performing simulation tests at the experimental site, this image analyzing method could solve the complex problems of traditional mechanical sensor installation and monitoring online, status assessment of the circuit breaker spring.

Chain and ladder models with two-body interactions and analytical ground states

NASA Astrophysics Data System (ADS)

Manna, Sourav; Nielsen, Anne E. B.

2018-05-01

We consider a family of spin-1 /2 models with few-body, SU(2)-invariant Hamiltonians and analytical ground states related to the one-dimensional (1D) Haldane-Shastry wave function. The spins are placed on the surface of a cylinder, and the standard 1D Haldane-Shastry model is obtained by placing the spins with equal spacing in a circle around the cylinder. Here, we show that another interesting family of models with two-body exchange interactions is obtained if we instead place the spins along one or two lines parallel to the cylinder axis, giving rise to chain and ladder models, respectively. We can change the scale along the cylinder axis without changing the radius of the cylinder. This gives us a parameter that controls the ratio between the circumference of the cylinder and all other length scales in the system. We use Monte Carlo simulations and analytical investigations to study how this ratio affects the properties of the models. If the ratio is large, we find that the two legs of the ladder decouple into two chains that are in a critical phase with Haldane-Shastry-like properties. If the ratio is small, the wave function reduces to a product of singlets. In between, we find that the behavior of the correlations and the Renyi entropy depends on the distance considered. For small distances the behavior is critical, and for long distances the correlations decay exponentially and the entropy shows an area law behavior. The distance up to which there is critical behavior gets larger as the ratio increases.

Heterojunction bipolar transistor technology for data acquisition and communication

NASA Technical Reports Server (NTRS)

Wang, C.; Chang, M.; Beccue, S.; Nubling, R.; Zampardi, P.; Sheng, N.; Pierson, R.

1992-01-01

Heterojunction Bipolar Transistor (HBT) technology has emerged as one of the most promising technologies for ultrahigh-speed integrated circuits. HBT circuits for digital and analog applications, data conversion, and power amplification have been realized, with speed performance well above 20 GHz. At Rockwell, a baseline AlGaAs/GaAs HBT technology has been established in a manufacturing facility. This paper describes the HBT technology, transistor characteristics, and HBT circuits for data acquisition and communication.

Printed circuit boards: a review on the perspective of sustainability.

PubMed

Canal Marques, André; Cabrera, José-María; Malfatti, Célia de Fraga

2013-12-15

Modern life increasingly requires newer equipments and more technology. In addition, the fact that society is highly consumerist makes the amount of discarded equipment as well as the amount of waste from the manufacture of new products increase at an alarming rate. Printed circuit boards, which form the basis of the electronics industry, are technological waste of difficult disposal whose recycling is complex and expensive due to the diversity of materials and components and their difficult separation. Currently, printed circuit boards have a fixing problem, which is migrating from traditional Pb-Sn alloys to lead-free alloys without definite choice. This replacement is an attempt to minimize the problem of Pb toxicity, but it does not change the problem of separation of the components for later reuse and/or recycling and leads to other problems, such as temperature rise, delamination, flaws, risks of mechanical shocks and the formation of "whiskers". This article presents a literature review on printed circuit boards, showing their structure and materials, the environmental problem related to the board, some the different alternatives for recycling, and some solutions that are being studied to reduce and/or replace the solder, in order to minimize the impact of solder on the printed circuit boards. Copyright © 2013 Elsevier Ltd. All rights reserved.

New technology for recovering residual metals from nonmetallic fractions of waste printed circuit boards.

PubMed

Zhang, Guangwen; He, Yaqun; Wang, Haifeng; Zhang, Tao; Wang, Shuai; Yang, Xing; Xia, Wencheng

2017-06-01

Recycling of waste printed circuit boards is important for environmental protection and sustainable resource utilization. Corona electrostatic separation has been widely used to recycle metals from waste printed circuit boards, but it has poor separation efficiency for finer sized fractions. In this study, a new process of vibrated gas-solid fluidized bed was used to recycle residual metals from nonmetallic fractions, which were treated using the corona electrostatic separation technology. The effects of three main parameters, i.e., vibration frequency, superficial air flow velocity, and fluidizing time on gravity segregation, were investigated using a vibrating gas-solid fluidized bed. Each size fraction had its own optimum parameters. Corresponding to their optimal segregation performance, the products from each experiment were analyzed using an X-ray fluorescence (XRF) and a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS). From the results, it can be seen that the metal recoveries of -1+0.5mm, -0.5+0.25mm, and -0.25mm size fractions were 86.39%, 82.22% and 76.63%, respectively. After separation, each metal content in the -1+0.5 or -0.5+0.25mm size fraction reduced to 1% or less, while the Fe and Cu contents are up to 2.57% and 1.50%, respectively, in the -0.25mm size fraction. Images of the nonmetallic fractions with a size of -0.25mm indicated that a considerable amount of clavate glass fibers existed in these nonmetallic fractions, which may explain why fine particles had the poorest segregation performance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of a 39.5 GHz Karp traveling wave tube for use in space

NASA Technical Reports Server (NTRS)

Jacquez, A.; Wilson, D.

1988-01-01

A millimeter-wave TWT was developed using a dispersive, high-impedance forward wave interaction structure based on a ladder, with non-space-harmonic interaction, for a tube with high gain per inch and high efficiency. The 'Tunneladder' interaction structure combines ladder properties modified to accommodate Pierce gun beam optics on a radially magnetized PM focusing structure. The development involved the fabrication of chemically milled, shaped ladders diffusion brazed to each ridge of a double ridged waveguide. Cold-test data are presented, representing the omega-Beta and impedance characteristics of the modified ladder circuit These results were used in small and large-signal computer programs to predict TWT gain and efficiency. A laboratory model tube was designed and fabricated, including all major subassemblies.

Stochastic Lotka-Volterra equations: A model of lagged diffusion of technology in an interconnected world

NASA Astrophysics Data System (ADS)

Chakrabarti, Anindya S.

2016-01-01

We present a model of technological evolution due to interaction between multiple countries and the resultant effects on the corresponding macro variables. The world consists of a set of economies where some countries are leaders and some are followers in the technology ladder. All of them potentially gain from technological breakthroughs. Applying Lotka-Volterra (LV) equations to model evolution of the technology frontier, we show that the way technology diffuses creates repercussions in the partner economies. This process captures the spill-over effects on major macro variables seen in the current highly globalized world due to trickle-down effects of technology.

Single-photon superradiant beating from a Doppler-broadened ladder-type atomic ensemble

NASA Astrophysics Data System (ADS)

Lee, Yoon-Seok; Lee, Sang Min; Kim, Heonoh; Moon, Han Seb

2017-12-01

We report on heralded-single-photon superradiant beating in the spontaneous four-wave mixing process of Doppler-broadened ladder-type 87Rb atoms. When Doppler-broadened atoms contribute to two-photon coherence, the detection probability amplitudes of the heralded single photons are coherently superposed despite inhomogeneous broadened atomic media. Single-photon superradiant beating is observed, which constitutes evidence for the coherent superposition of two-photon amplitudes from different velocity classes in the Doppler-broadened atomic ensemble. We present a theoretical model in which the single-photon superradiant beating originates from the interference between wavelength-separated two-photon amplitudes via the reabsorption filtering effect.

Advances in integrated photonic circuits for packet-switched interconnection

NASA Astrophysics Data System (ADS)

Williams, Kevin A.; Stabile, Ripalta

2014-03-01

Sustained increases in capacity and connectivity are needed to overcome congestion in a range of broadband communication network nodes. Packet routing and switching in the electronic domain are leading to unsustainable energy- and bandwidth-densities, motivating research into hybrid solutions: optical switching engines are introduced for massive-bandwidth data transport while the electronic domain is clocked at more modest GHz rates to manage routing. Commercially-deployed optical switching engines using MEMS technologies are unwieldy and too slow to reconfigure for future packet-based networking. Optoelectronic packet-compliant switch technologies have been demonstrated as laboratory prototypes, but they have so far mostly used discretely pigtailed components, which are impractical for control plane development and product assembly. Integrated photonics has long held the promise of reduced hardware complexity and may be the critical step towards packet-compliant optical switching engines. Recently a number of laboratories world-wide have prototyped optical switching circuits using monolithic integration technology with up to several hundreds of integrated optical components per chip. Our own work has focused on multi-input to multi-output switching matrices. Recently we have demonstrated 8×8×8λ space and wavelength selective switches using gated cyclic routers and 16×16 broadband switching chips using monolithic multi-stage networks. We now operate these advanced circuits with custom control planes implemented with FPGAs to explore real time packet routing in multi-wavelength, multi-port test-beds. We review our contributions in the context of state of the art photonic integrated circuit technology and packet optical switching hardware demonstrations.

ADDER CIRCUIT

DOEpatents

Jacobsohn, D.H.; Merrill, L.C.

1959-01-20

An improved parallel addition unit is described which is especially adapted for use in electronic digital computers and characterized by propagation of the carry signal through each of a plurality of denominationally ordered stages within a minimum time interval. In its broadest aspects, the invention incorporates a fast multistage parallel digital adder including a plurality of adder circuits, carry-propagation circuit means in all but the most significant digit stage, means for conditioning each carry-propagation circuit during the time period in which information is placed into the adder circuits, and means coupling carry-generation portions of thc adder circuit to the carry propagating means.

Laser patterning of highly conductive flexible circuits

NASA Astrophysics Data System (ADS)

Ji, Seok Young; Muhammed Ajmal, C.; Kim, Taehun; Chang, Won Seok; Baik, Seunghyun

2017-04-01

There has been considerable attention paid to highly conductive flexible adhesive (CFA) materials as electrodes and interconnectors for future flexible electronic devices. However, the patterning technology still needs to be developed to construct micro-scale electrodes and circuits. Here we developed the selective laser sintering technology where the pattering and curing were accomplished simultaneously without making additional masks. The CFA was composed of micro-scale Ag flakes, multiwalled carbon nanotubes decorated with Ag nanoparticles, and a nitrile-butadiene-rubber matrix. The Teflon-coated polyethylene terephthalate film was used as a flexible substrate. The width of lines (50-500 μm) and circuit patterns were controlled by the programmable scanning of a focused laser beam (power = 50 mW, scanning speed = 1 mm s-1). The laser irradiation removed solvent and induced effective coalescence among fillers providing a conductivity as high as 25 012 S cm-1. The conductivity stability was excellent under the ambient air and humid environments. The normalized resistance change of the pattern was smaller than 1.2 at the bending radius of 5 mm. The cyclability and adhesion of the laser-sintered line pattern on the substrate was excellent. A flexible circuit was fabricated sequentially for operating light emitting diodes during the bending motion, demonstrating excellent feasibility for practical applications in flexible electronics.

Laser patterning of highly conductive flexible circuits.

PubMed

Ji, Seok Young; Ajmal, C Muhammed; Kim, Taehun; Chang, Won Seok; Baik, Seunghyun

2017-04-21

There has been considerable attention paid to highly conductive flexible adhesive (CFA) materials as electrodes and interconnectors for future flexible electronic devices. However, the patterning technology still needs to be developed to construct micro-scale electrodes and circuits. Here we developed the selective laser sintering technology where the pattering and curing were accomplished simultaneously without making additional masks. The CFA was composed of micro-scale Ag flakes, multiwalled carbon nanotubes decorated with Ag nanoparticles, and a nitrile-butadiene-rubber matrix. The Teflon-coated polyethylene terephthalate film was used as a flexible substrate. The width of lines (50-500 μm) and circuit patterns were controlled by the programmable scanning of a focused laser beam (power = 50 mW, scanning speed = 1 mm s -1 ). The laser irradiation removed solvent and induced effective coalescence among fillers providing a conductivity as high as 25 012 S cm -1 . The conductivity stability was excellent under the ambient air and humid environments. The normalized resistance change of the pattern was smaller than 1.2 at the bending radius of 5 mm. The cyclability and adhesion of the laser-sintered line pattern on the substrate was excellent. A flexible circuit was fabricated sequentially for operating light emitting diodes during the bending motion, demonstrating excellent feasibility for practical applications in flexible electronics.

E3: Education, Experience, Employment The Economic Ladder to Success

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anne L Seifert

2011-10-01

Science, Technology, Engineering, and Math (STEM) literate citizenry is critical for Idaho's economy to effectively compete and grow in today's global marketplace and enhance Idaho workforce capabilities. Idaho's blueprint presents a collaboration design developed by a group of Idaho stakeholders including state level (STEM) educators, state and federal government, other agencies, and industry across the state. The purpose the Idaho Learn and Earn Blueprint Design is to describe a comprehensive plan for improving STEM education in Idaho through a collaborative partnerships and a series of grant supported projects underpinning this strategic design process building pathways to overcome hurdles in today'smore » economy, and moving communities and families up their economic ladder. The Idaho Learn and Earn Blueprint Design focuses on three industry sectors; energy, advanced manufacturing, and health care. All are important in Idaho and have room for job growth potential among both displaced workers and graduates. Representatives from each sector are members of the design team and assist in developing grants and implementing the actions outlined in the design as the program goes forward. Idaho's current programs are generally institution specific. Each of the state's two-year colleges, along with regional groups and employers, are already working towards improving STEM education across the state. A key aspect of this design is to bring these groups together to focus on four unique goals: (1) Providing industry driven curriculum directly tied to skill based career needs; (2) Enhancing collaboration among stakeholders; (3) Providing access to learn and earn programs; and (4) Improving public and student awareness and interest in targeted industry sector career and educational opportunities.« less

Color Coding of Circuit Quantities in Introductory Circuit Analysis Instruction

ERIC Educational Resources Information Center

Reisslein, Jana; Johnson, Amy M.; Reisslein, Martin

2015-01-01

Learning the analysis of electrical circuits represented by circuit diagrams is often challenging for novice students. An open research question in electrical circuit analysis instruction is whether color coding of the mathematical symbols (variables) that denote electrical quantities can improve circuit analysis learning. The present study…

X-ray effects on pacemaker type circuits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blamires, N.G.; Myatt, J.

1982-03-01

Queries have been raised concerning the potential hazards of X-ray irradiation on patients using the new generation of heart pacemakers based on digital circuitry. The present study was undertaken to provide some answers to these queries. The work was conducted in two parts. First, a literature search was done and, second, circuits using current state of the art digital technology were irradiated with X-rays. Watch circuits were chosen because of their availability and built-in facilities by which their function could be tested. Doses up to 330 rads were administered to them using energies of 46, 114, and 141 KeV. Themore » conclusion drawn from both parts of the study was that X-rays used for diagnostic purposes were unlikely to affect the performance of this type of circuit in any way. It was accepted that for therapeutic purposes doses far in excess of this are administered and circuit malfunctions are likely to occur. To assess the probability of a digital pacemaker malfunctioning, samples of that particular type would have to be irradiated at the relevant dose.« less

Design of an improved RCD buffer circuit for full bridge circuit

NASA Astrophysics Data System (ADS)

Yang, Wenyan; Wei, Xueye; Du, Yongbo; Hu, Liang; Zhang, Liwei; Zhang, Ou

2017-05-01

In the full bridge inverter circuit, when the switch tube suddenly opened or closed, the inductor current changes rapidly. Due to the existence of parasitic inductance of the main circuit. Therefore, the surge voltage between drain and source of the switch tube can be generated, which will have an impact on the switch and the output voltage. In order to ab sorb the surge voltage. An improve RCD buffer circuit is proposed in the paper. The peak energy will be absorbed through the buffer capacitor of the circuit. The part energy feedback to the power supply, another part release through the resistor in the form of heat, and the circuit can absorb the voltage spikes. This paper analyzes the process of the improved RCD snubber circuit, According to the specific parameters of the main circuit, a reasonable formula for calculating the resistance capacitance is given. A simulation model will be modulated in Multisim, which compared the waveform of tube voltage and the output waveform of the circuit without snubber circuit with the improved RCD snubber circuit. By comparing and analyzing, it is proved that the improved buffer circuit can absorb surge voltage. Finally, experiments are demonstrated to validate that the correctness of the RC formula and the improved RCD snubber circuit.

Compiler-aided systematic construction of large-scale DNA strand displacement circuits using unpurified components

NASA Astrophysics Data System (ADS)

Thubagere, Anupama J.; Thachuk, Chris; Berleant, Joseph; Johnson, Robert F.; Ardelean, Diana A.; Cherry, Kevin M.; Qian, Lulu

2017-02-01

Biochemical circuits made of rationally designed DNA molecules are proofs of concept for embedding control within complex molecular environments. They hold promise for transforming the current technologies in chemistry, biology, medicine and material science by introducing programmable and responsive behaviour to diverse molecular systems. As the transformative power of a technology depends on its accessibility, two main challenges are an automated design process and simple experimental procedures. Here we demonstrate the use of circuit design software, combined with the use of unpurified strands and simplified experimental procedures, for creating a complex DNA strand displacement circuit that consists of 78 distinct species. We develop a systematic procedure for overcoming the challenges involved in using unpurified DNA strands. We also develop a model that takes synthesis errors into consideration and semi-quantitatively reproduces the experimental data. Our methods now enable even novice researchers to successfully design and construct complex DNA strand displacement circuits.

InP-based three-dimensional photonic integrated circuits

NASA Astrophysics Data System (ADS)

Tsou, Diana; Zaytsev, Sergey; Pauchard, Alexandre; Hummel, Steve; Lo, Yu-Hwa

2001-10-01

Fast-growing internet traffic volumes require high data communication bandwidth over longer distances than short wavelength (850 nm) multi-mode fiber systems can provide. Access network bottlenecks put pressure on short-range (SR) telecommunication systems. To effectively address these datacom and telecom market needs, low cost, high-speed laser modules at 1310 and 1550 nm wavelengths are required. The great success of GaAs 850 nm VCSELs for Gb/s Ethernet has motivated efforts to extend VCSEL technology to longer wavelengths in the 1310 and 1550 nm regimes. However, the technological challenges associated with available intrinsic materials for long wavelength VCSELs are tremendous. Even with recent advances in this area, it is believed that significant additional development is necessary before long wavelength VCSELs that meet commercial specifications will be widely available. In addition, the more stringent OC192 and OC768 specifications for single-mode fiber (SMF) datacom may require more than just a long wavelength laser diode, VCSEL or not, to address numerous cost and performance issues. We believe that photonic integrated circuits, which compactly integrate surface-emitting lasers with additional active and passive optical components with extended functionality, will provide the best solutions to today's problems. Photonic integrated circuits (PICs) have been investigated for more than a decade. However, they have produced limited commercial impact to date primarily because the highly complicated fabrication processes produce significant yield and device performance issues. In this presentation, we will discuss a new technology platform for fabricating InP-based photonic integrated circuits compatible with surface-emitting laser technology. Employing InP transparency at 1310 and 1550 nm wavelengths, we have created 3-D photonic integrated circuits (PICs) by utilizing light beams in both surface normal and in-plane directions within the InP-based structure

Optical printed circuit board (O-PCB) and VLSI photonic integrated circuits: visions, challenges, and progresses

NASA Astrophysics Data System (ADS)

Lee, El-Hang; Lee, S. G.; O, B. H.; Park, S. G.; Noh, H. S.; Kim, K. H.; Song, S. H.

2006-09-01

A collective overview and review is presented on the original work conducted on the theory, design, fabrication, and in-tegration of micro/nano-scale optical wires and photonic devices for applications in a newly-conceived photonic systems called "optical printed circuit board" (O-PCBs) and "VLSI photonic integrated circuits" (VLSI-PIC). These are aimed for compact, high-speed, multi-functional, intelligent, light-weight, low-energy and environmentally friendly, low-cost, and high-volume applications to complement or surpass the capabilities of electrical PCBs (E-PCBs) and/or VLSI electronic integrated circuit (VLSI-IC) systems. These consist of 2-dimensional or 3-dimensional planar arrays of micro/nano-optical wires and circuits to perform the functions of all-optical sensing, storing, transporting, processing, switching, routing and distributing optical signals on flat modular boards or substrates. The integrated optical devices include micro/nano-scale waveguides, lasers, detectors, switches, sensors, directional couplers, multi-mode interference devices, ring-resonators, photonic crystal devices, plasmonic devices, and quantum devices, made of polymer, silicon and other semiconductor materials. For VLSI photonic integration, photonic crystals and plasmonic structures have been used. Scientific and technological issues concerning the processes of miniaturization, interconnection and integration of these systems as applicable to board-to-board, chip-to-chip, and intra-chip integration, are discussed along with applications for future computers, telecommunications, and sensor-systems. Visions and challenges toward these goals are also discussed.

An adjustable RF tuning element for microwave, millimeter wave, and submillimeter wave integrated circuits

NASA Technical Reports Server (NTRS)

Lubecke, Victor M.; Mcgrath, William R.; Rutledge, David B.

1991-01-01

Planar RF circuits are used in a wide range of applications from 1 GHz to 300 GHz, including radar, communications, commercial RF test instruments, and remote sensing radiometers. These circuits, however, provide only fixed tuning elements. This lack of adjustability puts severe demands on circuit design procedures and materials parameters. We have developed a novel tuning element which can be incorporated into the design of a planar circuit in order to allow active, post-fabrication tuning by varying the electrical length of a coplanar strip transmission line. It consists of a series of thin plates which can slide in unison along the transmission line, and the size and spacing of the plates are designed to provide a large reflection of RF power over a useful frequency bandwidth. Tests of this structure at 1 GHz to 3 Ghz showed that it produced a reflection coefficient greater than 0.90 over a 20 percent bandwidth. A 2 GHz circuit incorporating this tuning element was also tested to demonstrate practical tuning ranges. This structure can be fabricated for frequencies as high as 1000 GHz using existing micromachining techniques. Many commercial applications can benefit from this micromechanical RF tuning element, as it will aid in extending microwave integrated circuit technology into the high millimeter wave and submillimeter wave bands by easing constraints on circuit technology.

Quantum interference in heterogeneous superconducting-photonic circuits on a silicon chip.

PubMed

Schuck, C; Guo, X; Fan, L; Ma, X; Poot, M; Tang, H X

2016-01-21

Quantum information processing holds great promise for communicating and computing data efficiently. However, scaling current photonic implementation approaches to larger system size remains an outstanding challenge for realizing disruptive quantum technology. Two main ingredients of quantum information processors are quantum interference and single-photon detectors. Here we develop a hybrid superconducting-photonic circuit system to show how these elements can be combined in a scalable fashion on a silicon chip. We demonstrate the suitability of this approach for integrated quantum optics by interfering and detecting photon pairs directly on the chip with waveguide-coupled single-photon detectors. Using a directional coupler implemented with silicon nitride nanophotonic waveguides, we observe 97% interference visibility when measuring photon statistics with two monolithically integrated superconducting single-photon detectors. The photonic circuit and detector fabrication processes are compatible with standard semiconductor thin-film technology, making it possible to implement more complex and larger scale quantum photonic circuits on silicon chips.

Quantum interference in heterogeneous superconducting-photonic circuits on a silicon chip

PubMed Central

Schuck, C.; Guo, X.; Fan, L.; Ma, X.; Poot, M.; Tang, H. X.

2016-01-01

Quantum information processing holds great promise for communicating and computing data efficiently. However, scaling current photonic implementation approaches to larger system size remains an outstanding challenge for realizing disruptive quantum technology. Two main ingredients of quantum information processors are quantum interference and single-photon detectors. Here we develop a hybrid superconducting-photonic circuit system to show how these elements can be combined in a scalable fashion on a silicon chip. We demonstrate the suitability of this approach for integrated quantum optics by interfering and detecting photon pairs directly on the chip with waveguide-coupled single-photon detectors. Using a directional coupler implemented with silicon nitride nanophotonic waveguides, we observe 97% interference visibility when measuring photon statistics with two monolithically integrated superconducting single-photon detectors. The photonic circuit and detector fabrication processes are compatible with standard semiconductor thin-film technology, making it possible to implement more complex and larger scale quantum photonic circuits on silicon chips. PMID:26792424

Magnetophoretic circuits for digital control of single particles and cells

NASA Astrophysics Data System (ADS)

Lim, Byeonghwa; Reddy, Venu; Hu, Xinghao; Kim, Kunwoo; Jadhav, Mital; Abedini-Nassab, Roozbeh; Noh, Young-Woock; Lim, Yong Taik; Yellen, Benjamin B.; Kim, Cheolgi

2014-05-01

The ability to manipulate small fluid droplets, colloidal particles and single cells with the precision and parallelization of modern-day computer hardware has profound applications for biochemical detection, gene sequencing, chemical synthesis and highly parallel analysis of single cells. Drawing inspiration from general circuit theory and magnetic bubble technology, here we demonstrate a class of integrated circuits for executing sequential and parallel, timed operations on an ensemble of single particles and cells. The integrated circuits are constructed from lithographically defined, overlaid patterns of magnetic film and current lines. The magnetic patterns passively control particles similar to electrical conductors, diodes and capacitors. The current lines actively switch particles between different tracks similar to gated electrical transistors. When combined into arrays and driven by a rotating magnetic field clock, these integrated circuits have general multiplexing properties and enable the precise control of magnetizable objects.

SiGe Integrated Circuit Developments for SQUID/TES Readout

NASA Astrophysics Data System (ADS)

Prêle, D.; Voisin, F.; Beillimaz, C.; Chen, S.; Piat, M.; Goldwurm, A.; Laurent, P.

2018-03-01

SiGe integrated circuits dedicated to the readout of superconducting bolometer arrays for astrophysics have been developed since more than 10 years at APC. Whether for Cosmic Microwave Background (CMB) observations with the QUBIC ground-based experiment (Aumont et al. in astro-ph.IM, 2016. arXiv:1609.04372) or for the Hot and Energetic Universe science theme with the X-IFU instrument on-board of the ATHENA space mission (Barret et al. in SPIE 9905, space telescopes & instrumentation 2016: UV to γ Ray, 2016. https://doi.org/10.1117/12.2232432), several kinds of Transition Edge Sensor (TES) (Irwin and Hilton, in ENSS (ed) Cryogenic particle detection, Springer, Berlin, 2005) arrays have been investigated. To readout such superconducting detector arrays, we use time or frequency domain multiplexers (TDM, FDM) (Prêle in JINST 10:C08015, 2016. https://doi.org/10.1088/1748-0221/10/08/C08015) with Superconducting QUantum Interference Devices (SQUID). In addition to the SQUID devices, low-noise biasing and amplification are needed. These last functions can be obtained by using BiCMOS SiGe technology in an Application Specific Integrated Circuit (ASIC). ASIC technology allows integration of highly optimised circuits specifically designed for a unique application. Moreover, we could reach very low-noise and wide band amplification using SiGe bipolar transistor either at room or cryogenic temperatures (Cressler in J Phys IV 04(C6):C6-101, 1994. https://doi.org/10.1051/jp4:1994616). This paper discusses the use of SiGe integrated circuits for SQUID/TES readout and gives an update of the last developments dedicated to the QUBIC telescope and to the X-IFU instrument. Both ASIC called SQmux128 and AwaXe are described showing the interest of such SiGe technology for SQUID multiplexer controls.

Interplay between spin frustration and magnetism in the exactly solved two-leg mixed spin ladder

NASA Astrophysics Data System (ADS)

Qi, Yan; Lv, Song-Wei; Du, An; Yu, Nai-sen

2016-11-01

We study a mixed spin-(3/2, 1) ladder system with antiferromagnetic rung coupling and next-nearest-neighbor interaction. The exactly solved Ising-chain model is employed to investigate the ground-state properties and thermodynamics of the low-dimensional ladder system. Our results show that the competition between different exchange couplings brings in a large variety of ground states characterized by various values of normalized magnetization equal to 0, 1/5, 2/5, 3/5, 1. Moreover, an interesting double-peak structure is also detected in the thermal dependence of magnetic susceptibility and specific heat when the frustration comes into play. It is shown that the double-peak phenomenon at zero-field for the case of AF2 ground-state arises from the very strong antiferromagnetic rung coupling, while other cases are attributed to the excitations induced by temperature and external field around the phase boundary. Project supported by the National Natural Science Foundation of China (Grant No. 11547236), the General Project of the Education Department of Liaoning Province, China (Grant No. L2015130), the Fundamental Research Funds for the Central Universities, China (Grant Nos. DC201501065 and DCPY2016014), and the Doctoral Starting-up Foundation of Dalian Nationalities University, China.

Two-dimensional lattice gauge theories with superconducting quantum circuits

PubMed Central

Marcos, D.; Widmer, P.; Rico, E.; Hafezi, M.; Rabl, P.; Wiese, U.-J.; Zoller, P.

2014-01-01

A quantum simulator of U(1) lattice gauge theories can be implemented with superconducting circuits. This allows the investigation of confined and deconfined phases in quantum link models, and of valence bond solid and spin liquid phases in quantum dimer models. Fractionalized confining strings and the real-time dynamics of quantum phase transitions are accessible as well. Here we show how state-of-the-art superconducting technology allows us to simulate these phenomena in relatively small circuit lattices. By exploiting the strong non-linear couplings between quantized excitations emerging when superconducting qubits are coupled, we show how to engineer gauge invariant Hamiltonians, including ring-exchange and four-body Ising interactions. We demonstrate that, despite decoherence and disorder effects, minimal circuit instances allow us to investigate properties such as the dynamics of electric flux strings, signaling confinement in gauge invariant field theories. The experimental realization of these models in larger superconducting circuits could address open questions beyond current computational capability. PMID:25512676

High-speed logic integrated circuits with solution-processed self-assembled carbon nanotubes

NASA Astrophysics Data System (ADS)

Han, Shu-Jen; Tang, Jianshi; Kumar, Bharat; Falk, Abram; Farmer, Damon; Tulevski, George; Jenkins, Keith; Afzali, Ali; Oida, Satoshi; Ott, John; Hannon, James; Haensch, Wilfried

2017-09-01

As conventional monolithic silicon technology struggles to meet the requirements for the 7-nm technology node, there has been tremendous progress in demonstrating the scalability of carbon nanotube field-effect transistors down to the size that satisfies the 3-nm node and beyond. However, to date, circuits built with carbon nanotubes have overlooked key aspects of a practical logic technology and have stalled at simple functionality demonstrations. Here, we report high-performance complementary carbon nanotube ring oscillators using fully manufacturable processes, with a stage switching frequency of 2.82 GHz. The circuit was built on solution-processed, self-assembled carbon nanotube arrays with over 99.9% semiconducting purity, and the complementary feature was achieved by employing two different work function electrodes.

High-speed logic integrated circuits with solution-processed self-assembled carbon nanotubes.

PubMed

Han, Shu-Jen; Tang, Jianshi; Kumar, Bharat; Falk, Abram; Farmer, Damon; Tulevski, George; Jenkins, Keith; Afzali, Ali; Oida, Satoshi; Ott, John; Hannon, James; Haensch, Wilfried

2017-09-01

As conventional monolithic silicon technology struggles to meet the requirements for the 7-nm technology node, there has been tremendous progress in demonstrating the scalability of carbon nanotube field-effect transistors down to the size that satisfies the 3-nm node and beyond. However, to date, circuits built with carbon nanotubes have overlooked key aspects of a practical logic technology and have stalled at simple functionality demonstrations. Here, we report high-performance complementary carbon nanotube ring oscillators using fully manufacturable processes, with a stage switching frequency of 2.82 GHz. The circuit was built on solution-processed, self-assembled carbon nanotube arrays with over 99.9% semiconducting purity, and the complementary feature was achieved by employing two different work function electrodes.

Hood River and Pelton Ladder Evaluation Studies : Annual Report 1994.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, Erik A.; French, Rod A.; Ritchey, Alan D.

1995-09-01

In 1992, the Northwest Power Planning Council approved the Hood River and Pelton ladder master plans within the framework of the Columbia River Basin Fish and Wildlife Program. The master plans define an approach for implementing a hatchery supplementation program in the Hood River subbasin. The hatchery program as defined in the master plans is called the Hood River Hatchery Production Program (HRPP). The HRPP will be phased in over several years and will be jointly implemented by the Oregon Department of Fish and Wildlife (ODFW) and the Confederated Tribes of the Warm Springs (CTWS) Reservation. In December 1991, amore » monitoring and evaluation program was implemented in the Hood River subbasin to collect life history and production information on stocks of anadromous salmonids returning to the Hood River subbasin. The program was implemented to provide the baseline information needed to: (1) evaluate various management options for implementing the HRPP and (2) determine any post-project impacts the HRPP has on indigenous populations of resident fish. Information collected during the 1992-94 fiscal years will also be used to prepare an environmental impact statement (EIS) evaluating the program`s impact on the human environment. To begin construction on project facilities, it was proposed that the HRPP be implemented in two phases. Phase I would include work that would fall under a {open_quotes}categorical exclusion{close_quotes} from NEPA, and Phase II would include work requiring an EIS prior to implementation. This report summarizes the life history and escapement data collected in the Hood River subbasin and the status work of implemented under Phase I of the HR Life history and escapement data will be used to: (1) test the assumptions on which harvest and escapement goals for the Hood River and Pelton ladder master plans are based and (2) develop biologically based management recommendations for implementing the HRPP.« less

Chutes and Ladders in Hepatitis C Nucleoside Drug Development§

PubMed Central

Coats, Steven J.; Garnier-Amblard, Ethel C.; Amblard, Franck; Ehteshami, Maryam; Amiralaei, Sheida; Zhang, Hongwang; Zhou, Longhu; Boucle, Sebastien R. L.; Lu, Xiao; Bondada, Lavanya; Shelton, Jadd R.; Li, Hao; Liu, Peng; Li, Chengwei; Cho, Jong Hyun; Chavre, Satish N.; Zhou, Shaoman; Mathew, Judy; Schinazi, Raymond F.

2014-01-01

Chutes and Ladders is an exciting up-and-down-again game in which players race to be the first to the top of the board. Along the way, they will find ladders to help them advance, and chutes that will cause them to move backwards. The development of nucleoside analogs for clinical treatment of hepatitis C presents a similar scenario in which taking shortcuts may help quickly advance a program, but there is always a tremendous risk of being sent backwards as one competes for the finish line. In recent years the treatment options for chronic hepatitis C virus (HCV) infection have expand due to the development of a replicon based in vitro evaluation system, allowing for the identification of multiple drugable viral targets along with a concerted and substantial drug discovery effort. Three major drug targets have reached clinical study for chronic HCV infection: the NS3/4A serine protease, the large phosphoprotein NS5A, and the NS5B RNA-dependent RNA polymerase. Recently, two oral HCV protease inhibitors were approved by the FDA and were the first direct acting anti-HCV agents to result from the substantial research in this area. There are currently many new chemical entities from several different target classes that are being evaluated worldwide in clinical trials for their effectiveness at achieving a sustained virologic response (SVR) (Pham et al., 2004; Radkowski et al., 2005). Clearly the goal is to develop therapies leading to a cure that are safe, widely accessible and available, and effective against all HCV genotypes (GT), and all stages of the disease. Nucleoside analogs that target the HCV NS5B polymerase that have reached human clinical trials is the focus of this review as they have demonstrated significant advantages in the clinic with broader activity against the various HCV GT and a higher barrier to the development of resistant viruses when compared to all other classes of HCV inhibitors. PMID:24275341

Extremely flexible nanoscale ultrathin body silicon integrated circuits on plastic.

PubMed

Shahrjerdi, Davood; Bedell, Stephen W

2013-01-09

In recent years, flexible devices based on nanoscale materials and structures have begun to emerge, exploiting semiconductor nanowires, graphene, and carbon nanotubes. This is primarily to circumvent the existing shortcomings of the conventional flexible electronics based on organic and amorphous semiconductors. The aim of this new class of flexible nanoelectronics is to attain high-performance devices with increased packing density. However, highly integrated flexible circuits with nanoscale transistors have not yet been demonstrated. Here, we show nanoscale flexible circuits on 60 Å thick silicon, including functional ring oscillators and memory cells. The 100-stage ring oscillators exhibit the stage delay of ~16 ps at a power supply voltage of 0.9 V, the best reported for any flexible circuits to date. The mechanical flexibility is achieved by employing the controlled spalling technology, enabling the large-area transfer of the ultrathin body silicon devices to a plastic substrate at room temperature. These results provide a simple and cost-effective pathway to enable ultralight flexible nanoelectronics with unprecedented level of system complexity based on mainstream silicon technology.

Glass Fibers for Printed Circuit Boards

NASA Astrophysics Data System (ADS)

Longobardo, Anthony V.

Fiberglass imparts numerous positive benefits to modern printed circuit boards. Reinforced laminate composites have an excellent cost-performance relationship that makes sense for most applications. At the leading edge of the technology, new glass fibers with improved properties, in combination with the best resin systems available, are able to meet very challenging performance, cost, and regulatory demands while remaining manufacturable.

GaAs-based JFET and PHEMT technologies for ultra-low-power microwave circuits operating at frequencies up to 2.4 GHz

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baca, A.G.; Hietala, V.M.; Greenway, D.

1998-05-01

In this work the authors report results of narrowband amplifiers designed for milliwatt and submilliwatt power consumption using JFET and pseudomorphic high electron mobility transistors (PHEMT) GaAs-based technologies. Enhancement-mode JFETs were used to design both a hybrid amplifier with off-chip matching as well as a monolithic microwave integrated circuit (MMIC) with on-chip matching. The hybrid amplifier achieved 8--10 dB of gain at 2.4 GHz and 1 mW. The MMIC achieved 10 dB of gain at 2.4 GHz and 2 mW. Submilliwatt circuits were also explored by using 0.25 {micro}m PHEMTs. 25 {micro}W power levels were achieved with 5 dB ofmore » gain for a 215 MHz hybrid amplifier. These results significantly reduce power consumption levels achievable with the JFETs or prior MESFET, heterostructure field effect transistor (HFET), or Si bipolar results from other laboratories.« less

Development of Curriculum Content for a Unique Career Ladder Multi-Entry/Multi-Exit Nursing Program. Final Report.

ERIC Educational Resources Information Center

Rosbach, Ellen M.

A project was undertaken to develop the curriculum content for a unique career ladder multi-entry/multi-exit nursing program that would provide training for nurse aides, practical nurses, and registered nurses. The major objectives of the project were to conduct a review of the literature on curriculum materials presently in use, to develop 11…

Monolithic microwave integrated circuits for sensors, radar, and communications systems; Proceedings of the Meeting, Orlando, FL, Apr. 2-4, 1991

NASA Technical Reports Server (NTRS)

Leonard, Regis F. (Editor); Bhasin, Kul B. (Editor)

1991-01-01

Consideration is given to MMICs for airborne phased arrays, monolithic GaAs integrated circuit millimeter wave imaging sensors, accurate design of multiport low-noise MMICs up to 20 GHz, an ultralinear low-noise amplifier technology for space communications, variable-gain MMIC module for space applications, a high-efficiency dual-band power amplifier for radar applications, a high-density circuit approach for low-cost MMIC circuits, coplanar SIMMWIC circuits, recent advances in monolithic phased arrays, and system-level integrated circuit development for phased-array antenna applications. Consideration is also given to performance enhancement in future communications satellites with MMIC technology insertion, application of Ka-band MMIC technology for an Orbiter/ACTS communications experiment, a space-based millimeter wave debris tracking radar, low-noise high-yield octave-band feedback amplifiers to 20 GHz, quasi-optical MESFET VCOs, and a high-dynamic-range mixer using novel balun structure.

Knowing One's Lot in Life versus Climbing the Social Ladder: The Formation of Redistributive Preferences in Urban China

ERIC Educational Resources Information Center

Smyth, Russell; Mishra, Vinod; Qian, Xiaolei

2010-01-01

This paper examines, how individual preferences for redistribution in general and redistribution to improve access to education, improve social protection for the poor, reduce income inequality and reduce unemployment depend on beliefs about what determines one's lot in life and self-assessed prospects for climbing the social ladder in urban…

A Phenomenological Examination of Virtual Game Developers' Experiences Using Jacob's Ladder Pre-Production Design Tactic

ERIC Educational Resources Information Center

Brown-Turner, Jasmine

2017-01-01

Edutainment refers to curriculum and instruction designed with a clear educational purpose, including multi-faceted virtual learning game design. Tools such as the Jacob's Ladder pre-production design tactic have been developed to ensure that voices of both engineers and educators are heard. However, it is unclear how development team members…

New technology for separating resin powder and fiberglass powder from fiberglass-resin powder of waste printed circuit boards.

PubMed

Li, Jia; Gao, Bei; Xu, Zhenming

2014-05-06

New recycling technologies have been developed lately to enhance the value of the fiberglass powder-resin powder fraction (FRP) from waste printed circuit boards. The definite aim of the present paper is to present some novel methods that use the image forces for the separation of the resin powder and fiberglass powder generated from FRP during the corona electrostatic separating process. The particle shape charactization and particle trajectory simulation were performed on samples of mixed non-metallic particles. The simulation results pointed out that particles of resin powder and particles of fiberglass powder had different detach trajectories at the conditions of the same size and certain device parameters. An experiment carried out using a corona electrostatic separator validated the possibility of sorting these particles based on the differences in their shape characteristics. The differences in the physical properties of the different types of particles provided the technical basis for the development of electrostatic separation technologies for the recycling industry.

Integrated circuit with dissipative layer for photogenerated carriers

DOEpatents

Myers, David R.

1989-01-01

The sensitivity of an integrated circuit to single-event upsets is decreased by providing a dissi The U.S. Government has rights in this invention pursuant to Contract No. DE-ACO4-76DP00789 between the Department of Energy and AT&T Technologies, Inc.

Integrated circuit with dissipative layer for photogenerated carriers

DOEpatents

Myers, D.R.

1989-09-12

The sensitivity of an integrated circuit to single-event upsets is decreased by providing a dissi The U.S. Government has rights in this invention pursuant to Contract No. DE-ACO4-76DP00789 between the Department of Energy and AT&T Technologies, Inc.

Quantum-Circuit Refrigerator

NASA Astrophysics Data System (ADS)

MöTtöNen, Mikko; Tan, Kuan Y.; Masuda, Shumpei; Partanen, Matti; Lake, Russell E.; Govenius, Joonas; Silveri, Matti; Grabert, Hermann

Quantum technology holds great potential in providing revolutionizing practical applications. However, fast and precise cooling of the functional quantum degrees of freedom on demand remains a major challenge in many solid-state implementations, such as superconducting circuits. We demonstrate direct cooling of a superconducting resonator mode using voltage-controllable quantum tunneling of electrons in a nanoscale refrigerator. In our first experiments on this type of a quantum-circuit refrigerator, we measure the drop in the mode temperature by electron thermometry at a resistor which is coupled to the resonator mode through ohmic losses. To eliminate unwanted dissipation, we remove the probe resistor and directly observe the power spectrum of the resonator output in agreement with the so-called P(E) theory. We also demonstrate in microwave reflection experiments that the internal quality factor of the resonator can be tuned by orders of magnitude. In the future, our refrigerator can be integrated with different quantum electric devices, potentially enhancing their performance. For example, it may prove useful in the initialization of superconducting quantum bits and in dissipation-assisted quantum annealing. We acknowledge European Research Council Grant SINGLEOUT (278117) and QUESS (681311) for funding.

Parameter space of experimental chaotic circuits with high-precision control parameters.

PubMed

de Sousa, Francisco F G; Rubinger, Rero M; Sartorelli, José C; Albuquerque, Holokx A; Baptista, Murilo S

2016-08-01

We report high-resolution measurements that experimentally confirm a spiral cascade structure and a scaling relationship of shrimps in the Chua's circuit. Circuits constructed using this component allow for a comprehensive characterization of the circuit behaviors through high resolution parameter spaces. To illustrate the power of our technological development for the creation and the study of chaotic circuits, we constructed a Chua circuit and study its high resolution parameter space. The reliability and stability of the designed component allowed us to obtain data for long periods of time (∼21 weeks), a data set from which an accurate estimation of Lyapunov exponents for the circuit characterization was possible. Moreover, this data, rigorously characterized by the Lyapunov exponents, allows us to reassure experimentally that the shrimps, stable islands embedded in a domain of chaos in the parameter spaces, can be observed in the laboratory. Finally, we confirm that their sizes decay exponentially with the period of the attractor, a result expected to be found in maps of the quadratic family.

A nanocryotron comparator can connect single-flux-quantum circuits to conventional electronics

NASA Astrophysics Data System (ADS)

Zhao, Qing-Yuan; McCaughan, Adam N.; Dane, Andrew E.; Berggren, Karl K.; Ortlepp, Thomas

2017-04-01

Integration with conventional electronics offers a straightforward and economical approach to upgrading existing superconducting technologies, such as scaling up superconducting detectors into large arrays and combining single flux quantum (SFQ) digital circuits with semiconductor logic gates and memories. However, direct output signals from superconducting devices (e.g., Josephson junctions) are usually not compatible with the input requirements of conventional devices (e.g., transistors). Here, we demonstrate the use of a single three-terminal superconducting-nanowire device, called the nanocryotron (nTron), as a digital comparator to combine SFQ circuits with mature semiconductor circuits such as complementary metal oxide semiconductor (CMOS) circuits. Since SFQ circuits can digitize output signals from general superconducting devices and CMOS circuits can interface existing CMOS-compatible electronics, our results demonstrate the feasibility of a general architecture that uses an nTron as an interface to realize a ‘super-hybrid’ system consisting of superconducting detectors, superconducting quantum electronics, CMOS logic gates and memories, and other conventional electronics.

A method for identifying EMI critical circuits during development of a large C3

NASA Astrophysics Data System (ADS)

Barr, Douglas H.

The circuit analysis methods and process Boeing Aerospace used on a large, ground-based military command, control, and communications (C3) system are described. This analysis was designed to help identify electromagnetic interference (EMI) critical circuits. The methodology used the MIL-E-6051 equipment criticality categories as the basis for defining critical circuits, relational database technology to help sort through and account for all of the approximately 5000 system signal cables, and Macintosh Plus personal computers to predict critical circuits based on safety margin analysis. The EMI circuit analysis process systematically examined all system circuits to identify which ones were likely to be EMI critical. The process used two separate, sequential safety margin analyses to identify critical circuits (conservative safety margin analysis, and detailed safety margin analysis). These analyses used field-to-wire and wire-to-wire coupling models using both worst-case and detailed circuit parameters (physical and electrical) to predict circuit safety margins. This process identified the predicted critical circuits that could then be verified by test.

Development of circuit model for arcing on solar panels

NASA Astrophysics Data System (ADS)

Mehta, Bhoomi K.; Deshpande, S. P.; Mukherjee, S.; Gupta, S. B.; Ranjan, M.; Rane, R.; Vaghela, N.; Acharya, V.; Sudhakar, M.; Sankaran, M.; Suresh, E. P.

2010-02-01

The increased requirements of payload capacity of the satellites have resulted in much higher power requirements of the satellites. In order to minimize the energy loss during power transmission due to cable loss, use of high voltage solar panels becomes necessary. When a satellite encounters space plasma it floats negatively with respect to the surrounding space plasma environment. At high voltage, charging and discharging on solar panels causes the power system breakdown. Once a solar panel surface is charged and potential difference between surface insulator and conductor exceeds certain value, electrostatic discharge (ESD) may occur. This ESD may trigger a secondary arc that can destroy the solar panel circuit. ESD is also called as primary or minor arc and secondary is called major arc. The energy of minor arc is supplied by the charge stored in the coverglass of solar array and is a pulse of typically several 100 ns to several 100 μs duration. The damage caused by minor arc is less compared to major arcs, but it is observed that the minor arc is cause of major arc. Therefore it is important to develop an understanding of minor arc and mitigation techniques. In this paper we present a linear circuit analysis for minor arcs on solar panels. To study arcing event, a ground experimental facility to simulate space plasma environment has been developed at Facilitation Centre for Industrial Plasma Technologies (Institute for Plasma Research) in collaboration with Indian Space Research Organization's ISRO Satellite Technology Centre (ISAC). A linear circuit model has been developed to explain the experimental results by representing the coverglass, solar cell interconnect and wiring by an LCR circuit and the primary arc by an equivalent LR circuit. The aim of the circuit analysis is to predict the arc current which flows through the arc plasma. It is established from the model that the current depends on various parameters like potential difference between insulator

Teachers' Career Ladder Policy in Ethiopia: An Opportunity for Professional Growth or ''a Stick Disguised as a Carrot?''

ERIC Educational Resources Information Center

Tekleselassie, Abebayehu A.

2005-01-01

In response to the ever-declining status of the teaching profession, and its adverse effects on the country's educational system, the Federal Ministry of Education in Ethiopia introduced a policy of the teachers' career ladder in 1994. While reformers believe that the introduction of the policy has improved the condition of the teaching…

Plug-and-Play Multicellular Circuits with Time-Dependent Dynamic Responses.

PubMed

Urrios, Arturo; Gonzalez-Flo, Eva; Canadell, David; de Nadal, Eulàlia; Macia, Javier; Posas, Francesc

2018-04-20

Synthetic biology studies aim to develop cellular devices for biomedical applications. These devices, based on living instead of electronic or electromechanic technology, might provide alternative treatments for a wide range of diseases. However, the feasibility of these devices depends, in many cases, on complex genetic circuits that must fulfill physiological requirements. In this work, we explored the potential of multicellular architectures to act as an alternative to complex circuits for implementation of new devices. As a proof of concept, we developed specific circuits for insulin or glucagon production in response to different glucose levels. Here, we show that fundamental features, such as circuit's affinity or sensitivity, are dependent on the specific configuration of the multicellular consortia, providing a method for tuning these properties without genetic engineering. As an example, we have designed and built circuits with an incoherent feed-forward loop architecture (FFL) that can be easily adjusted to generate single pulse responses. Our results might serve as a blueprint for future development of cellular devices for glycemia regulation in diabetic patients.

Static Holes in Geometrically Frustrated Bow Tie Ladder

NASA Astrophysics Data System (ADS)

Martins, George; Brenig, Wolfram

2007-03-01

Doping of the geometrically frustrated bow-tie spin ladder with static holes is investigated by a complementary approach using exact diagonalization and hard-core quantum dimers. Results for the thermodynamics in the undoped case, the singlet density of states, the hole-binding energy, and the spin correlations will be presented. We find that the static holes polarize their vicinity by a localization of singlets in order to reduce the frustration. As a consequence the singlet polarization cloud induces short range repulsive forces between the holes with oscillatory longer range behavior. For those systems we have studied, most results for the quantum dimer approach are found to be qualitatively if not quantitatively in agreement with exact diagonalization. The ground state of the undoped system is non-degenerate with translationally invariant nearest-neighbor spin correlations up to a few unit cells, which is consistent with a spin liquid state or a valence bond crystal with very large unit cell. C. Waldtmann, A. Kreutzmann, U. Schollwock, K. Maisinger, and H.-U. Everts, Phys. Rev. B 62, 9472 (2000).

Radiation-Hard Complementary Integrated Circuits Based on Semiconducting Single-Walled Carbon Nanotubes.

PubMed

McMorrow, Julian J; Cress, Cory D; Gaviria Rojas, William A; Geier, Michael L; Marks, Tobin J; Hersam, Mark C

2017-03-28

Increasingly complex demonstrations of integrated circuit elements based on semiconducting single-walled carbon nanotubes (SWCNTs) mark the maturation of this technology for use in next-generation electronics. In particular, organic materials have recently been leveraged as dopant and encapsulation layers to enable stable SWCNT-based rail-to-rail, low-power complementary metal-oxide-semiconductor (CMOS) logic circuits. To explore the limits of this technology in extreme environments, here we study total ionizing dose (TID) effects in enhancement-mode SWCNT-CMOS inverters that employ organic doping and encapsulation layers. Details of the evolution of the device transport properties are revealed by in situ and in operando measurements, identifying n-type transistors as the more TID-sensitive component of the CMOS system with over an order of magnitude larger degradation of the static power dissipation. To further improve device stability, radiation-hardening approaches are explored, resulting in the observation that SWNCT-CMOS circuits are TID-hard under dynamic bias operation. Overall, this work reveals conditions under which SWCNTs can be employed for radiation-hard integrated circuits, thus presenting significant potential for next-generation satellite and space applications.

Developing Managerial Learning Styles in the Context of the Strategic Application of Information and Communications Technologies.

ERIC Educational Resources Information Center

Holtham, Clive; Courtney, Nigel

2001-01-01

Training for 561 executives in the use of information and communications technologies was based on a model, the Executive Learning Ladder. Results indicated that sense making was accelerated when conducted in peer groups before being extended to less-experienced managers. Learning preference differences played a role. (Contains 38 references.) (SK)

Design of synthetic biological logic circuits based on evolutionary algorithm.

PubMed

Chuang, Chia-Hua; Lin, Chun-Liang; Chang, Yen-Chang; Jennawasin, Tanagorn; Chen, Po-Kuei

2013-08-01

The construction of an artificial biological logic circuit using systematic strategy is recognised as one of the most important topics for the development of synthetic biology. In this study, a real-structured genetic algorithm (RSGA), which combines general advantages of the traditional real genetic algorithm with those of the structured genetic algorithm, is proposed to deal with the biological logic circuit design problem. A general model with the cis-regulatory input function and appropriate promoter activity functions is proposed to synthesise a wide variety of fundamental logic gates such as NOT, Buffer, AND, OR, NAND, NOR and XOR. The results obtained can be extended to synthesise advanced combinational and sequential logic circuits by topologically distinct connections. The resulting optimal design of these logic gates and circuits are established via the RSGA. The in silico computer-based modelling technology has been verified showing its great advantages in the purpose.

System-Level Integrated Circuit (SLIC) Technology Development for Phased Array Antenna Applications

NASA Technical Reports Server (NTRS)

Windyka, John A.; Zablocki, Ed G.

1997-01-01

This report documents the efforts and progress in developing a 'system-level' integrated circuit, or SLIC, for application in advanced phased array antenna systems. The SLIC combines radio-frequency (RF) microelectronics, digital and analog support circuitry, and photonic interfaces into a single micro-hybrid assembly. Together, these technologies provide not only the amplitude and phase control necessary for electronic beam steering in the phased array, but also add thermally-compensated automatic gain control, health and status feedback, bias regulation, and reduced interconnect complexity. All circuitry is integrated into a compact, multilayer structure configured for use as a two-by-four element phased array module, operating at 20 Gigahertz, using a Microwave High-Density Interconnect (MHDI) process. The resultant hardware is constructed without conventional wirebonds, maintains tight inter-element spacing, and leads toward low-cost mass production. The measured performances and development issues associated with both the two-by-four element module and the constituent elements are presented. Additionally, a section of the report describes alternative architectures and applications supported by the SLIC electronics. Test results show excellent yield and performance of RF circuitry and full automatic gain control for multiple, independent channels. Digital control function, while suffering from lower manufacturing yield, also proved successful.

Automatic Digital Switching Specialist Career Ladder: United States Air Force Job Inventory. AFSCs 29530, 29570, and 29590.

ERIC Educational Resources Information Center

Air Force Personnel and Training Research Center, Lackland AFB, TX.

The U. S. Air Force job inventory for the automatic digital switching specialist career ladder is divided into 12 categories, each of which is broken down into a duty-task list. Space is provided for Air Force personnel filling out the inventory to check whether each task is at present part of their duties. The 12 categories are: organizing and…

Silicon photonics integrated circuits: a manufacturing platform for high density, low power optical I/O's.

PubMed

Absil, Philippe P; Verheyen, Peter; De Heyn, Peter; Pantouvaki, Marianna; Lepage, Guy; De Coster, Jeroen; Van Campenhout, Joris

2015-04-06

Silicon photonics integrated circuits are considered to enable future computing systems with optical input-outputs co-packaged with CMOS chips to circumvent the limitations of electrical interfaces. In this paper we present the recent progress made to enable dense multiplexing by exploiting the integration advantage of silicon photonics integrated circuits. We also discuss the manufacturability of such circuits, a key factor for a wide adoption of this technology.

Some finite terms from ladder diagrams in three and four loop maximal supergravity

NASA Astrophysics Data System (ADS)

Basu, Anirban

2015-10-01

We consider the finite part of the leading local interactions in the low energy expansion of the four graviton amplitude from the ladder skeleton diagrams in maximal supergravity on T 2, at three and four loops. At three loops, we express the {D}8{{R}}4 and {D}10{{R}}4 amplitudes as integrals over the moduli space of an underlying auxiliary geometry. These amplitudes are evaluated exactly for special values of the the moduli of the auxiliary geometry, where the integrand simplifies. We also perform a similar analysis for the {D}8{{R}}4 amplitude at four loops that arise from the ladder skeleton diagrams for a special value of a parameter in the moduli space of the auxiliary geometry. While the dependence of the amplitudes on the volume of the T 2 is very simple, the dependence on the complex structure of the T 2 is quite intricate. In some of the cases, the amplitude consists of terms each of which factorizes into a product of two {SL}(2,{{Z}}) invariant modular forms. While one of the factors is a non-holomorphic Eisenstein series, the other factor splits into a sum of modular forms each of which satisfies a Poisson equation on moduli space with source terms that are bilinear in the Eisenstein series. This leads to several possible perturbative contributions unto genus 5 in type II string theory on S1. Unlike the one and two loop supergravity analysis, these amplitudes also receive non-perturbative contributions from bound states of three D-(anti)instantons in the IIB theory.

Basic guidelines to introduce electric circuit simulation software in a general physics course

NASA Astrophysics Data System (ADS)

Moya, A. A.

2018-05-01

The introduction of electric circuit simulation software for undergraduate students in a general physics course is proposed in order to contribute to the constructive learning of electric circuit theory. This work focuses on the lab exercises based on dc, transient and ac analysis in electric circuits found in introductory physics courses, and shows how students can use the simulation software to do simple activities associated with a lab exercise itself and with related topics. By introducing electric circuit simulation programs in a general physics course as a brief activitiy complementing lab exercise, students develop basic skills in using simulation software, improve their knowledge on the topology of electric circuits and perceive that the technology contributes to their learning, all without reducing the time spent on the actual content of the course.

High density circuit technology, part 3

NASA Technical Reports Server (NTRS)

Wade, T. E.

1982-01-01

Dry processing - both etching and deposition - and present/future trends in semiconductor technology are discussed. In addition to a description of the basic apparatus, terminology, advantages, glow discharge phenomena, gas-surface chemistries, and key operational parameters for both dry etching and plasma deposition processes, a comprehensive survey of dry processing equipment (via vendor listing) is also included. The following topics are also discussed: fine-line photolithography, low-temperature processing, packaging for dense VLSI die, the role of integrated optics, and VLSI and technology innovations.

Experimental Durability Testing of 4H SiC JFET Integrated Circuit Technology at 727 C

NASA Technical Reports Server (NTRS)

Spry, David; Neudeck, Phil; Chen, Liangyu; Chang, Carl; Lukco, Dorothy; Beheim, Glenn M

2016-01-01

We have reported SiC integrated circuits (IC's) with two levels of metal interconnect that have demonstrated prolonged operation for thousands of hours at their intended peak ambient operational temperature of 500 C [1, 2]. However, it is recognized that testing of semiconductor microelectronics at temperatures above their designed operating envelope is vital to qualification. Towards this end, we previously reported operation of a 4H-SiC JFET IC ring oscillator on an initial fast thermal ramp test through 727 C [3]. However, this thermal ramp was not ended until a peak temperature of 880 C (well beyond failure) was attained. Further experiments are necessary to better understand failure mechanisms and upper temperature limit of this extreme-temperature capable 4H-SiC IC technology. Here we report on additional experimental testing of custom-packaged 4H-SiC JFET IC devices at temperatures above 500 C. In one test, the temperature was ramped and then held at 727 C, and the devices were periodically measured until electrical failure was observed. A 4H-SiC JFET on this chip electrically functioned with little change for around 25 hours at 727 C before rapid increases in device resistance caused failure. In a second test, devices from our next generation 4H-SiC JFET ICs were ramped up and then held at 700 C (which is below the maximum deposition temperature of the dielectrics). Three ring oscillators functioned for 8 hours at this temperature before degradation. In a third experiment, an alternative die attach of gold paste and package lid was used, and logic circuit operation was demonstrated for 143.5 hours at 700 C.

Intelligent structures technology

NASA Astrophysics Data System (ADS)

Crawley, Edward F.

1991-07-01

Viewgraphs on intelligent structures technology are presented. Topics covered include: embedding electronics; electrical and mechanical compatibility; integrated circuit chip packaged for embedding; embedding devices within composite structures; test of embedded circuit in G/E coupon; temperature/humidity/bias test; single-chip microcomputer control experiment; and structural shape determination.

Intelligent structures technology

NASA Technical Reports Server (NTRS)

Crawley, Edward F.

1991-01-01

Viewgraphs on intelligent structures technology are presented. Topics covered include: embedding electronics; electrical and mechanical compatibility; integrated circuit chip packaged for embedding; embedding devices within composite structures; test of embedded circuit in G/E coupon; temperature/humidity/bias test; single-chip microcomputer control experiment; and structural shape determination.

A novel high-speed CMOS circuit based on a gang of capacitors

NASA Astrophysics Data System (ADS)

Sharroush, Sherif M.

2017-08-01

There is no doubt that complementary metal-oxide semiconductor (CMOS) circuits with wide fan-in suffers from the relatively sluggish operation. In this paper, a circuit that contains a gang of capacitors sharing their charge with each other is proposed as an alternative to long N-channel MOS and P-channel MOS stacks. The proposed scheme is investigated quantitatively and verified by simulation using the 45-nm CMOS technology with VDD = 1 V. The time delay, area and power consumption of the proposed scheme are investigated and compared with the conventional static CMOS logic circuit. It is verified that the proposed scheme achieves 52% saving in the average propagation delay for eight inputs and that it has a smaller area compared to the conventional CMOS logic when the number of inputs exceeds three and a smaller power consumption for a number of inputs exceeding two. The impacts of process variations, component mismatches and technology scaling on the proposed scheme are also investigated.

Current limiter circuit system

DOEpatents

Witcher, Joseph Brandon; Bredemann, Michael V.

2017-09-05

An apparatus comprising a steady state sensing circuit, a switching circuit, and a detection circuit. The steady state sensing circuit is connected to a first, a second and a third node. The first node is connected to a first device, the second node is connected to a second device, and the steady state sensing circuit causes a scaled current to flow at the third node. The scaled current is proportional to a voltage difference between the first and second node. The switching circuit limits an amount of current that flows between the first and second device. The detection circuit is connected to the third node and the switching circuit. The detection circuit monitors the scaled current at the third node and controls the switching circuit to limit the amount of the current that flows between the first and second device when the scaled current is greater than a desired level.

Micromachined Integrated Quantum Circuit Containing a Superconducting Qubit

NASA Astrophysics Data System (ADS)

Brecht, T.; Chu, Y.; Axline, C.; Pfaff, W.; Blumoff, J. Z.; Chou, K.; Krayzman, L.; Frunzio, L.; Schoelkopf, R. J.

2017-04-01

We present a device demonstrating a lithographically patterned transmon integrated with a micromachined cavity resonator. Our two-cavity, one-qubit device is a multilayer microwave-integrated quantum circuit (MMIQC), comprising a basic unit capable of performing circuit-QED operations. We describe the qubit-cavity coupling mechanism of a specialized geometry using an electric-field picture and a circuit model, and obtain specific system parameters using simulations. Fabrication of the MMIQC includes lithography, etching, and metallic bonding of silicon wafers. Superconducting wafer bonding is a critical capability that is demonstrated by a micromachined storage-cavity lifetime of 34.3 μ s , corresponding to a quality factor of 2 ×106 at single-photon energies. The transmon coherence times are T1=6.4 μ s , and T2echo=11.7 μ s . We measure qubit-cavity dispersive coupling with a rate χq μ/2 π =-1.17 MHz , constituting a Jaynes-Cummings system with an interaction strength g /2 π =49 MHz . With these parameters we are able to demonstrate circuit-QED operations in the strong dispersive regime with ease. Finally, we highlight several improvements and anticipated extensions of the technology to complex MMIQCs.

Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications.

PubMed

Takeda, Yasunori; Hayasaka, Kazuma; Shiwaku, Rei; Yokosawa, Koji; Shiba, Takeo; Mamada, Masashi; Kumaki, Daisuke; Fukuda, Kenjiro; Tokito, Shizuo

2016-05-09

Ultrathin electronic circuits that can be manufactured by using conventional printing technologies are key elements necessary to realize wearable health sensors and next-generation flexible electronic devices. Due to their low level of power consumption, complementary (CMOS) circuits using both types of semiconductors can be easily employed in wireless devices. Here, we describe ultrathin CMOS logic circuits, for which not only the source/drain electrodes but also the semiconductor layers were printed. Both p-type and n-type organic thin film transistor devices were employed in a D-flip flop circuit in the newly developed stacked structure and exhibited excellent electrical characteristics, including good carrier mobilities of 0.34 and 0.21 cm(2) V(-1) sec(-1), and threshold voltages of nearly 0 V with low operating voltages. These printed organic CMOS D-flip flop circuits exhibit operating frequencies of 75 Hz and demonstrate great potential for flexible and printed electronics technology, particularly for wearable sensor applications with wireless connectivity.

Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications

PubMed Central

Takeda, Yasunori; Hayasaka, Kazuma; Shiwaku, Rei; Yokosawa, Koji; Shiba, Takeo; Mamada, Masashi; Kumaki, Daisuke; Fukuda, Kenjiro; Tokito, Shizuo

2016-01-01

Ultrathin electronic circuits that can be manufactured by using conventional printing technologies are key elements necessary to realize wearable health sensors and next-generation flexible electronic devices. Due to their low level of power consumption, complementary (CMOS) circuits using both types of semiconductors can be easily employed in wireless devices. Here, we describe ultrathin CMOS logic circuits, for which not only the source/drain electrodes but also the semiconductor layers were printed. Both p-type and n-type organic thin film transistor devices were employed in a D-flip flop circuit in the newly developed stacked structure and exhibited excellent electrical characteristics, including good carrier mobilities of 0.34 and 0.21 cm2 V−1 sec−1, and threshold voltages of nearly 0 V with low operating voltages. These printed organic CMOS D-flip flop circuits exhibit operating frequencies of 75 Hz and demonstrate great potential for flexible and printed electronics technology, particularly for wearable sensor applications with wireless connectivity. PMID:27157914

Efficiently characterizing the total error in quantum circuits

NASA Astrophysics Data System (ADS)

Carignan-Dugas, Arnaud; Wallman, Joel J.; Emerson, Joseph

A promising technological advancement meant to enlarge our computational means is the quantum computer. Such a device would harvest the quantum complexity of the physical world in order to unfold concrete mathematical problems more efficiently. However, the errors emerging from the implementation of quantum operations are likewise quantum, and hence share a similar level of intricacy. Fortunately, randomized benchmarking protocols provide an efficient way to characterize the operational noise within quantum devices. The resulting figures of merit, like the fidelity and the unitarity, are typically attached to a set of circuit components. While important, this doesn't fulfill the main goal: determining if the error rate of the total circuit is small enough in order to trust its outcome. In this work, we fill the gap by providing an optimal bound on the total fidelity of a circuit in terms of component-wise figures of merit. Our bound smoothly interpolates between the classical regime, in which the error rate grows linearly in the circuit's length, and the quantum regime, which can naturally allow quadratic growth. Conversely, our analysis substantially improves the bounds on single circuit element fidelities obtained through techniques such as interleaved randomized benchmarking. This research was supported by the U.S. Army Research Office through Grant W911NF- 14-1-0103, CIFAR, the Government of Ontario, and the Government of Canada through NSERC and Industry Canada.

Development of Physical Demand Profiles for Four Airman Career Ladders. Interim Report for Period 1 July 1972-1 November 1974.

ERIC Educational Resources Information Center

Koym, Kenneth G.

The document investigates certain physical characteristics of airman occupations in terms of the dexterity, muscular coordination, and sensory discrimination required. It examines the feasibility of estimating physical demands in jobs using incumbent ratings and compares physical demand profiles for four career ladders: (1) avionic instrument…

Resonance Frequency Readout Circuit for a 900 MHz SAW Device

PubMed Central

Liu, Heng; Zhang, Chun; Weng, Zhaoyang; Guo, Yanshu; Wang, Zhihua

2017-01-01

A monolithic resonance frequency readout circuit with high resolution and short measurement time is presented for a 900 MHz RF surface acoustic wave (SAW) sensor. The readout circuit is composed of a fractional-N phase-locked loop (PLL) as the stimulus source to the SAW device and a phase-based resonance frequency detecting circuit using successive approximation (SAR). A new resonance frequency searching strategy has been proposed based on the fact that the SAW device phase-frequency response crosses zero monotonically around the resonance frequency. A dedicated instant phase difference detecting circuit is adopted to facilitate the fast SAR operation for resonance frequency searching. The readout circuit has been implemented in 180 nm CMOS technology with a core area of 3.24 mm2. In the experiment, it works with a 900 MHz SAW resonator with a quality factor of Q = 130. Experimental results show that the readout circuit consumes 7 mW power from 1.6 V supply. The frequency resolution is 733 Hz, and the relative accuracy is 0.82 ppm, and it takes 0.48 ms to complete one measurement. Compared to the previous results in the literature, this work has achieved the shortest measurement time with a trade-off between measurement accuracy and measurement time. PMID:28914799

Resonance Frequency Readout Circuit for a 900 MHz SAW Device.

PubMed

Liu, Heng; Zhang, Chun; Weng, Zhaoyang; Guo, Yanshu; Wang, Zhihua

2017-09-15

A monolithic resonance frequency readout circuit with high resolution and short measurement time is presented for a 900 MHz RF surface acoustic wave (SAW) sensor. The readout circuit is composed of a fractional-N phase-locked loop (PLL) as the stimulus source to the SAW device and a phase-based resonance frequency detecting circuit using successive approximation (SAR). A new resonance frequency searching strategy has been proposed based on the fact that the SAW device phase-frequency response crosses zero monotonically around the resonance frequency. A dedicated instant phase difference detecting circuit is adopted to facilitate the fast SAR operation for resonance frequency searching. The readout circuit has been implemented in 180 nm CMOS technology with a core area of 3.24 mm². In the experiment, it works with a 900 MHz SAW resonator with a quality factor of Q = 130. Experimental results show that the readout circuit consumes 7 mW power from 1.6 V supply. The frequency resolution is 733 Hz, and the relative accuracy is 0.82 ppm, and it takes 0.48 ms to complete one measurement. Compared to the previous results in the literature, this work has achieved the shortest measurement time with a trade-off between measurement accuracy and measurement time.

Vertically integrated, three-dimensional nanowire complementary metal-oxide-semiconductor circuits.

PubMed

Nam, SungWoo; Jiang, Xiaocheng; Xiong, Qihua; Ham, Donhee; Lieber, Charles M

2009-12-15

Three-dimensional (3D), multi-transistor-layer, integrated circuits represent an important technological pursuit promising advantages in integration density, operation speed, and power consumption compared with 2D circuits. We report fully functional, 3D integrated complementary metal-oxide-semiconductor (CMOS) circuits based on separate interconnected layers of high-mobility n-type indium arsenide (n-InAs) and p-type germanium/silicon core/shell (p-Ge/Si) nanowire (NW) field-effect transistors (FETs). The DC voltage output (V(out)) versus input (V(in)) response of vertically interconnected CMOS inverters showed sharp switching at close to the ideal value of one-half the supply voltage and, moreover, exhibited substantial DC gain of approximately 45. The gain and the rail-to-rail output switching are consistent with the large noise margin and minimal static power consumption of CMOS. Vertically interconnected, three-stage CMOS ring oscillators were also fabricated by using layer-1 InAs NW n-FETs and layer-2 Ge/Si NW p-FETs. Significantly, measurements of these circuits demonstrated stable, self-sustained oscillations with a maximum frequency of 108 MHz, which represents the highest-frequency integrated circuit based on chemically synthesized nanoscale materials. These results highlight the flexibility of bottom-up assembly of distinct nanoscale materials and suggest substantial promise for 3D integrated circuits.

Contemporary approaches to neural circuit manipulation and mapping: focus on reward and addiction

PubMed Central

Saunders, Benjamin T.; Richard, Jocelyn M.; Janak, Patricia H.

2015-01-01

Tying complex psychological processes to precisely defined neural circuits is a major goal of systems and behavioural neuroscience. This is critical for understanding adaptive behaviour, and also how neural systems are altered in states of psychopathology, such as addiction. Efforts to relate psychological processes relevant to addiction to activity within defined neural circuits have been complicated by neural heterogeneity. Recent advances in technology allow for manipulation and mapping of genetically and anatomically defined neurons, which when used in concert with sophisticated behavioural models, have the potential to provide great insight into neural circuit bases of behaviour. Here we discuss contemporary approaches for understanding reward and addiction, with a focus on midbrain dopamine and cortico-striato-pallidal circuits. PMID:26240425

Universal discrete Fourier optics RF photonic integrated circuit architecture.

PubMed

Hall, Trevor J; Hasan, Mehedi

2016-04-04

This paper describes a coherent electro-optic circuit architecture that generates a frequency comb consisting of N spatially separated orders using a generalised Mach-Zenhder interferometer (MZI) with its N × 1 combiner replaced by an optical N × N Discrete Fourier Transform (DFT). Advantage may be taken of the tight optical path-length control, component and circuit symmetries and emerging trimming algorithms offered by photonic integration in any platform that offers linear electro-optic phase modulation such as LiNbO_3, silicon, III-V or hybrid technology. The circuit architecture subsumes all MZI-based RF photonic circuit architectures in the prior art given an appropriate choice of output port(s) and dimension N although the principal application envisaged is phase correlated subcarrier generation for all optical orthogonal frequency division multiplexing. A transfer matrix approach is used to model the operation of the architecture. The predictions of the model are validated by simulations performed using an industry standard software tool. Implementation is found to be practical.

Circuit-based versus full-wave modelling of active microwave circuits

NASA Astrophysics Data System (ADS)

Bukvić, Branko; Ilić, Andjelija Ž.; Ilić, Milan M.

2018-03-01

Modern full-wave computational tools enable rigorous simulations of linear parts of complex microwave circuits within minutes, taking into account all physical electromagnetic (EM) phenomena. Non-linear components and other discrete elements of the hybrid microwave circuit are then easily added within the circuit simulator. This combined full-wave and circuit-based analysis is a must in the final stages of the circuit design, although initial designs and optimisations are still faster and more comfortably done completely in the circuit-based environment, which offers real-time solutions at the expense of accuracy. However, due to insufficient information and general lack of specific case studies, practitioners still struggle when choosing an appropriate analysis method, or a component model, because different choices lead to different solutions, often with uncertain accuracy and unexplained discrepancies arising between the simulations and measurements. We here design a reconfigurable power amplifier, as a case study, using both circuit-based solver and a full-wave EM solver. We compare numerical simulations with measurements on the manufactured prototypes, discussing the obtained differences, pointing out the importance of measured parameters de-embedding, appropriate modelling of discrete components and giving specific recipes for good modelling practices.