Higher order acoustoelastic Lamb wave propagation in stressed plates.

PubMed

Pei, Ning; Bond, Leonard J

2016-11-01

Modeling and experiments are used to investigate Lamb wave propagation in the direction perpendicular to an applied stress. Sensitivity, in terms of changes in velocity, for both symmetrical and anti-symmetrical modes was determined. Codes were developed based on analytical expressions for waves in loaded plates and they were used to give wave dispersion curves. The experimental system used a pair of compression wave transducers on variable angle wedges, with set separation, and variable frequency tone burst excitation, on an aluminum plate 0.16 cm thick with uniaxial applied loads. The loads, which were up to 600 με, were measured using strain gages. Model results and experimental data are in good agreement. It was found that the change in Lamb wave velocity, due to the acoustoelastic effect, for the S 1 mode exhibits about ten times more sensitive, in terms of velocity change, than the traditional bulk wave measurements, and those performed using the fundamental Lamb modes. The data presented demonstrate the potential for the use of higher order Lamb modes for online industrial stress measurement in plate, and that the higher sensitivity seen offers potential for improved measurement systems.

Non-contact ultrasonic gas flow metering using air-coupled leaky Lamb waves.

PubMed

Fan, Zichuan; Jiang, Wentao; Wright, William M D

2018-04-23

This paper describes a completely non-contact ultrasonic method of gas flow metering using air-coupled leaky Lamb waves. To show proof of principle, a simplified representation of gas flow in a duct, comprising two separated thin isotropic plates with a gas flowing between them, has been modelled and investigated experimentally. An airborne compression wave emitted from an air-coupled capacitive ultrasonic transducer excited a leaky Lamb wave in the first plate in a non-contact manner. The leakage of this Lamb wave crossed the gas flow at an angle between the two plates as a compression wave, and excited a leaky Lamb wave in the second plate. An air-coupled capacitive ultrasonic transducer on the opposite side of this second plate then detected the airborne compression wave leakage from the second Lamb wave. As the gas flow shifted the wave field between the two plates, the point of Lamb wave excitation in the second plate was displaced in proportion to the gas flow rate. Two such measurements, in opposite directions, formed a completely non-contact contra-propagating Lamb wave flow meter, allowing measurement of the flow velocity between the plates. A COMSOL Multiphysics® model was used to visualize the wave fields, and accurately predicted the time differences that were then measured experimentally. Experiments using different Lamb wave frequencies and plate materials were also similarly verified. This entirely non-contact airborne approach to Lamb wave flow metering could be applied in place of clamp-on techniques in thin-walled ducts or pipes. Copyright © 2018 Elsevier B.V. All rights reserved.

A Fatigue Crack Size Evaluation Method Based on Lamb Wave Simulation and Limited Experimental Data

PubMed Central

He, Jingjing; Ran, Yunmeng; Liu, Bin; Yang, Jinsong; Guan, Xuefei

2017-01-01

This paper presents a systematic and general method for Lamb wave-based crack size quantification using finite element simulations and Bayesian updating. The method consists of construction of a baseline quantification model using finite element simulation data and Bayesian updating with limited Lamb wave data from target structure. The baseline model correlates two proposed damage sensitive features, namely the normalized amplitude and phase change, with the crack length through a response surface model. The two damage sensitive features are extracted from the first received S0 mode wave package. The model parameters of the baseline model are estimated using finite element simulation data. To account for uncertainties from numerical modeling, geometry, material and manufacturing between the baseline model and the target model, Bayesian method is employed to update the baseline model with a few measurements acquired from the actual target structure. A rigorous validation is made using in-situ fatigue testing and Lamb wave data from coupon specimens and realistic lap-joint components. The effectiveness and accuracy of the proposed method is demonstrated under different loading and damage conditions. PMID:28902148

Adhesive joint evaluation by ultrasonic interface and lamb waves

NASA Technical Reports Server (NTRS)

Rokhlin, S. I.

1986-01-01

Some results on the application of interface and Lamb waves for the study of curing of thin adhesive layers were summarized. In the case of thick substrates (thickness much more than the wave length) the interface waves can be used. In this case the experimental data can be inverted and the shear modulus of the adhesive film may be explicitly found based on the measured interface wave velocity. It is shown that interface waves can be used for the study of curing of structural adhesives as a function of different temperatures and other experimental conditions. The kinetics of curing was studied. In the case of thin substrates the wave phenomena are much more complicated. It is shown that for successful measurements proper selection of experimental conditions is very important. This can be done based on theoretical estimations. For correctly selected experimental conditions the Lamb waves may be a sensitive probe of adhesive bond quality and may be used or cure monitoring.

Peri-Elastodynamic Simulations of Guided Ultrasonic Waves in Plate-Like Structure with Surface Mounted PZT.

PubMed

Patra, Subir; Ahmed, Hossain; Banerjee, Sourav

2018-01-18

Peridynamic based elastodynamic computation tool named Peri-elastodynamics is proposed herein to simulate the three-dimensional (3D) Lamb wave modes in materials for the first time. Peri-elastodynamics is a nonlocal meshless approach which is a scale-independent generalized technique to visualize the acoustic and ultrasonic waves in plate-like structure, micro-electro-mechanical systems (MEMS) and nanodevices for their respective characterization. In this article, the characteristics of the fundamental Lamb wave modes are simulated in a sample plate-like structure. Lamb wave modes are generated using a surface mounted piezoelectric (PZT) transducer which is actuated from the top surface. The proposed generalized Peri-elastodynamics method is not only capable of simulating two dimensional (2D) in plane wave under plane strain condition formulated previously but also capable of accurately simulating the out of plane Symmetric and Antisymmetric Lamb wave modes in plate like structures in 3D. For structural health monitoring (SHM) of plate-like structures and nondestructive evaluation (NDE) of MEMS devices, it is necessary to simulate the 3D wave-damage interaction scenarios and visualize the different wave features due to damages. Hence, in addition, to simulating the guided ultrasonic wave modes in pristine material, Lamb waves were also simulated in a damaged plate. The accuracy of the proposed technique is verified by comparing the modes generated in the plate and the mode shapes across the thickness of the plate with theoretical wave analysis.

Quantitative Evaluation of Delamination in Composites Using Lamb Waves

NASA Astrophysics Data System (ADS)

Michalcová, L.; Hron, R.

2018-03-01

Ultrasonic guided wave monitoring has become very popular in the area of structural health monitoring (SHM) of aerospace structures. Any possible type of damage must be reliably assessed. The paper deals with delamination length determination in DCB specimens using Lamb waves. An analytical equation based on the velocity dependence on variable thickness is utilized. The group velocity of the fundamental antisymmetric A0 mode rapidly changes in a particular range of the frequency-thickness product. Using the same actuation frequency the propagation velocity is different for delaminated structure. Lamb wave based delamination lengths were compared to the visually determined lengths. The method of the wave velocity determination proved to be essential. More accurate results were achieved by tracking the maximum amplitude of A0 mode than the first signal arrival. These findings are considered as the basis for the damage evaluation of complex structures.

Numerical study on static component generation from the primary Lamb waves propagating in a plate with nonlinearity

NASA Astrophysics Data System (ADS)

Wan, Xiang; Tse, Peter W.; Zhang, Xuhui; Xu, Guanghua; Zhang, Qing; Fan, Hongwei; Mao, Qinghua; Dong, Ming; Wang, Chuanwei; Ma, Hongwei

2018-04-01

Under the discipline of nonlinear ultrasonics, in addition to second harmonic generation, static component generation is another frequently used nonlinear ultrasonic behavior in non-destructive testing (NDT) and structural health monitoring (SHM) communities. However, most previous studies on static component generation are mainly based on using longitudinal waves. It is desirable to extend static component generation from primary longitudinal waves to primary Lamb waves. In this paper, static component generation from the primary Lamb waves is studied. Two major issues are numerically investigated. First, the mode of static displacement component generated from different primary Lamb wave modes is identified. Second, cumulative effect of static displacement component from different primary Lamb wave modes is also discussed. Our study results show that the static component wave packets generated from the primary S0, A0 and S1 modes share the almost same group velocity equal to the phase velocity of S0 mode tending to zero frequency c plate . The finding indicates that whether the primary mode is S0, A0 or S1, the static components generated from these primary modes always share the nature of S0 mode. This conclusion is also verified by the displacement filed of these static components that the horizontal displacement field is almost uniform and the vertical displacement filed is antisymmetric across the thickness of the plate. The uniform distribution of horizontal displacement filed enables the static component, regardless of the primary Lamb modes, to be a promising technique for evaluating microstructural damages buried in the interior of a structure. Our study also illustrates that the static components are cumulative regardless of whether the phase velocity of the primary and secondary waves is matched or not. This observation indicates that the static component overcomes the limitations of the traditional nonlinear Lamb waves satisfying phase velocity matching condition to achieve cumulative second harmonic generation. This nature also enables the primary Lamb waves excited at a low center frequency to generate static component used for inspecting large-scale structures with micro-scale damages.

Lamb Wave Assessment of Fatigue and Thermal Damage in Composites

NASA Technical Reports Server (NTRS)

Seale, Michael D.; Smith, Barry T.; Prosser, W. H.

2004-01-01

Among the various techniques available, ultrasonic Lamb waves offer a convenient method of evaluating composite materials. Since the Lamb wave velocity depends on the elastic properties of a structure, an effective tool exists to monitor damage in composites by measuring the velocity of these waves. Lamb wave measurements can propagate over long distances and are sensitive to the desired in-plane elastic properties of the material. This paper describes two studies which monitor fatigue damage and two studies which monitor thermal damage in composites using Lamb waves. In the fatigue studies, the Lamb wave velocity is compared to modulus measurements obtained using strain gage measurements in the first experiment and the velocity is monitored along with the crack density in the second. In the thermal damage studies, one examines samples which were exposed to varying temperatures for a three minute duration and the second includes rapid thermal damage in composites by intense laser beams. In all studies, the Lamb wave velocity is demonstrated to be an excellent method to monitor damage in composites.

Intelligent feature selection techniques for pattern classification of Lamb wave signals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hinders, Mark K.; Miller, Corey A.

2014-02-18

Lamb wave interaction with flaws is a complex, three-dimensional phenomenon, which often frustrates signal interpretation schemes based on mode arrival time shifts predicted by dispersion curves. As the flaw severity increases, scattering and mode conversion effects will often dominate the time-domain signals, obscuring available information about flaws because multiple modes may arrive on top of each other. Even for idealized flaw geometries the scattering and mode conversion behavior of Lamb waves is very complex. Here, multi-mode Lamb waves in a metal plate are propagated across a rectangular flat-bottom hole in a sequence of pitch-catch measurements corresponding to the double crossholemore » tomography geometry. The flaw is sequentially deepened, with the Lamb wave measurements repeated at each flaw depth. Lamb wave tomography reconstructions are used to identify which waveforms have interacted with the flaw and thereby carry information about its depth. Multiple features are extracted from each of the Lamb wave signals using wavelets, which are then fed to statistical pattern classification algorithms that identify flaw severity. In order to achieve the highest classification accuracy, an optimal feature space is required but it’s never known a priori which features are going to be best. For structural health monitoring we make use of the fact that physical flaws, such as corrosion, will only increase over time. This allows us to identify feature vectors which are topologically well-behaved by requiring that sequential classes “line up” in feature vector space. An intelligent feature selection routine is illustrated that identifies favorable class distributions in multi-dimensional feature spaces using computational homology theory. Betti numbers and formal classification accuracies are calculated for each feature space subset to establish a correlation between the topology of the class distribution and the corresponding classification accuracy.« less

Delamination detection in smart composite beams using Lamb waves

NASA Astrophysics Data System (ADS)

Ip, Kim-Ho; Mai, Yiu-Wing

2004-06-01

This paper presents a feasibility study on using Lamb waves to detect and locate through-width delamination in fiber-reinforced plastic beams. An active diagnostic system is proposed for clamped-free specimens. It consists of a piezoelectric patch and an accelerometer both mounted near the support. Such a system can locate damage in an absolute sense, that is, a priori knowledge on the response from pristine specimens is not required. The fundamental anti-symmetric Lamb wave mode is chosen as the diagnostic wave. It is generated by applying a voltage in the form of sinusoidal bursts to the piezoelectric patch. The proposed system was applied to locate delaminations in some fabricated Kevlar/epoxy beam specimens. With an appropriate actuating frequency, distortions of waveforms due to boundary reflections can be reduced. Based on their arrival times and the known propagating speed of Lamb waves, the delaminations can be located. The errors associated with the predicted damage positions range from 4.5% to 8.5%.

Research on a Lamb Wave and Particle Filter-Based On-Line Crack Propagation Prognosis Method.

PubMed

Chen, Jian; Yuan, Shenfang; Qiu, Lei; Cai, Jian; Yang, Weibo

2016-03-03

Prognostics and health management techniques have drawn widespread attention due to their ability to facilitate maintenance activities based on need. On-line prognosis of fatigue crack propagation can offer information for optimizing operation and maintenance strategies in real-time. This paper proposes a Lamb wave-particle filter (LW-PF)-based method for on-line prognosis of fatigue crack propagation which takes advantages of the possibility of on-line monitoring to evaluate the actual crack length and uses a particle filter to deal with the crack evolution and monitoring uncertainties. The piezoelectric transducers (PZTs)-based active Lamb wave method is adopted for on-line crack monitoring. The state space model relating to crack propagation is established by the data-driven and finite element methods. Fatigue experiments performed on hole-edge crack specimens have validated the advantages of the proposed method.

Lamb Wave Tomography for Corrosion Mapping

NASA Technical Reports Server (NTRS)

Hinders, Mark K.; McKeon, James C. P.

1999-01-01

As the world-wide civil aviation fleet continues to age, methods for accurately predicting the presence of structural flaws-such as hidden corrosion-that compromise airworthiness become increasingly necessary. Ultrasonic guided waves, Lamb waves, allow large sections of aircraft structures to be rapidly inspected. However, extracting quantitative information from Lamb wave data has always involved highly trained personnel with a detailed knowledge of mechanical-waveguide physics. Our work focuses on using a variety of different tomographic reconstruction techniques to graphically represent the Lamb wave data in images that can be easily interpreted by technicians. Because the velocity of Lamb waves depends on thickness, we can convert the travel times of the fundamental Lamb modes into a thickness map of the inspection region. In this paper we show results for the identification of single or multiple back-surface corrosion areas in typical aluminum aircraft skin structures.

Robust laser-based detection of Lamb waves using photo-EMF sensors

NASA Astrophysics Data System (ADS)

Klein, Marvin B.; Bacher, Gerald D.

1998-03-01

Lamb waves are easily generated and detected using laser techniques. It has been shown that both symmetric and antisymmetric modes can be produced, using single-spot and phased array generation. Detection has been demonstrated with Michelson interferometers, but these instruments can not function effectively on rough surfaces. By contrast, the confocal Fabry-Perot interferometer can interrogate rough surfaces, but generally is not practical for operation below 300 kHz. In this paper we will present Lamb wave data on a number of parts using a robust, adaptive receiver based on photo-emf detection. This receiver has useful sensitivity down to at least 100 kHz, can process speckled beams and can be easily configured to measure both out-of-plane and in- plane motion with a single probe beam.

Nonlinear Lamb waves for fatigue damage identification in FRP-reinforced steel plates.

PubMed

Wang, Yikuan; Guan, Ruiqi; Lu, Ye

2017-09-01

A nonlinear Lamb-wave-based method for fatigue crack detection in steel plates with and without carbon fibre reinforcement polymer (CFRP) reinforcement is presented in this study. Both numerical simulation and experimental evaluation were performed for Lamb wave propagation and its interaction with a fatigue crack on these two steel plate types. With the generation of the second harmonic, the damage-induced wave nonlinearities were identified by surface-bonded piezoelectric sensors. Numerical simulation revealed that the damage-induced wave component at the second harmonic was slightly affected by the existence of CFRP laminate, although the total wave energy was decreased because of wave leakage into the CFRP laminate. Due to unavoidable nonlinearity from the experimental environments, it was impractical to directly extract the time-of-flight of the second harmonic for locating the crack. To this end, the correlation coefficient of benchmark and signal with damage at double frequency in the time domain was calculated, based on which an imaging method was introduced to locate the fatigue crack in steel plates with and without CFRP laminates. Copyright © 2017 Elsevier B.V. All rights reserved.

Numerical and experimental study of Lamb wave propagation in a two-dimensional acoustic black hole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Shiling; Shen, Zhonghua, E-mail: shenzh@njust.edu.cn; Lomonosov, Alexey M.

2016-06-07

The propagation of laser-generated Lamb waves in a two-dimensional acoustic black-hole structure was studied numerically and experimentally. The geometrical acoustic theory has been applied to calculate the beam trajectories in the region of the acoustic black hole. The finite element method was also used to study the time evolution of propagating waves. An optical system based on the laser-Doppler vibration method was assembled. The effect of the focusing wave and the reduction in wave speed of the acoustic black hole has been validated.

Selective Excitation of Lamb-Waves for Damage Detection in Composites

NASA Astrophysics Data System (ADS)

Petculescu, G.; Krishnaswamy, S.; Achenbach, J. D.

2006-03-01

Sensors based on periodic arrays of coherent piezoelectric sources (comb design) are used to selectively excite and detect Lamb waves in aluminum and AS4/3601 unidirectional carbon-epoxy plates. 110 μm PVDF film poled in the thickness direction is used as piezoelectric material. An algorithm to eliminate the effect of coupling in amplitude measurements, using individual Lamb modes excited/detected by the same transducer pair, is described. A multiple-impact test showing a decrease in amplitude and group velocity as damage progresses is used as an example.

Improving the resolution for Lamb wave testing via a smoothed Capon algorithm

NASA Astrophysics Data System (ADS)

Cao, Xuwei; Zeng, Liang; Lin, Jing; Hua, Jiadong

2018-04-01

Lamb wave testing is promising for damage detection and evaluation in large-area structures. The dispersion of Lamb waves is often unavoidable, restricting testing resolution and making the signal hard to interpret. A smoothed Capon algorithm is proposed in this paper to estimate the accurate path length of each wave packet. In the algorithm, frequency domain whitening is firstly used to obtain the transfer function in the bandwidth of the excitation pulse. Subsequently, wavenumber domain smoothing is employed to reduce the correlation between wave packets. Finally, the path lengths are determined by distance domain searching based on the Capon algorithm. Simulations are applied to optimize the number of smoothing times. Experiments are performed on an aluminum plate consisting of two simulated defects. The results demonstrate that spatial resolution is improved significantly by the proposed algorithm.

Lamb wave dispersion ultrasound vibrometry (LDUV) method for quantifying mechanical properties of viscoelastic solids.

PubMed

Nenadic, Ivan Z; Urban, Matthew W; Mitchell, Scott A; Greenleaf, James F

2011-04-07

Diastolic dysfunction is the inability of the left ventricle to supply sufficient stroke volumes under normal physiological conditions and is often accompanied by stiffening of the left-ventricular myocardium. A noninvasive technique capable of quantifying viscoelasticity of the myocardium would be beneficial in clinical settings. Our group has been investigating the use of shear wave dispersion ultrasound vibrometry (SDUV), a noninvasive ultrasound-based method for quantifying viscoelasticity of soft tissues. The primary motive of this study is the design and testing of viscoelastic materials suitable for validation of the Lamb wave dispersion ultrasound vibrometry (LDUV), an SDUV-based technique for measuring viscoelasticity of tissues with plate-like geometry. We report the results of quantifying viscoelasticity of urethane rubber and gelatin samples using LDUV and an embedded sphere method. The LDUV method was used to excite antisymmetric Lamb waves and measure the dispersion in urethane rubber and gelatin plates. An antisymmetric Lamb wave model was fitted to the wave speed dispersion data to estimate elasticity and viscosity of the materials. A finite element model of a viscoelastic plate submerged in water was used to study the appropriateness of the Lamb wave dispersion equations. An embedded sphere method was used as an independent measurement of the viscoelasticity of the urethane rubber and gelatin. The FEM dispersion data were in excellent agreement with the theoretical predictions. Viscoelasticity of the urethane rubber and gelatin obtained using the LDUV and embedded sphere methods agreed within one standard deviation. LDUV studies on excised porcine myocardium sample were performed to investigate the feasibility of the approach in preparation for open-chest in vivo studies. The results suggest that the LDUV technique can be used to quantify the mechanical properties of soft tissues with a plate-like geometry.

Near field effect on elasticity measurement for cartilage-bone structure using Lamb wave method.

PubMed

Xu, Hao; Chen, Shigao; An, Kai-Nan; Luo, Zong-Ping

2017-10-30

Cartilage elasticity changes with cartilage degeneration. Hence, cartilage elasticity detection might be an alternative to traditional imaging methods for the early diagnosis of osteoarthritis. Based on the wave propagation measurement, Shear wave elastography (SWE) become an emerging non-invasive elasticity detection method. The wave propagation model, which is affected by tissue shapes, is crucial for elasticity estimating in SWE. However, wave propagation model for cartilage was unclear. This study aimed to establish a wave propagation model for the cartilage-bone structure. We fabricated a cartilage-bone structure, and studied the elasticity measurement and wave propagation by experimental and numerical Lamb wave method (LWM). Results indicated the wave propagation model satisfied the lamb wave theory for two-layered structure. Moreover, a near field region, which affects wave speed measurements and whose occurrence can be prevented if the wave frequency is larger than one critical frequency, was observed. Our findings would provide a theoretical foundation for further application of LWM in elasticity measurement of cartilage in vivo. It can help the application of LWM to the diagnosis of osteoarthritis.

Detecting Lamb waves with broadband acousto-ultrasonic signals in composite structures

NASA Technical Reports Server (NTRS)

Kautz, Harold E.

1992-01-01

Lamb waves can be produced and detected in ceramic matrix composites (CMC) and metal matrix composites (MMC) plates using the acousto-ultrasonic configuration employing broadband transducers. Experimental dispersion curves of lowest symmetric and lowest antisymmetric modes behave in a manner analogous to the graphite/polymer theoretical curves. In this study a basis has been established for analyzing Lamb wave velocities for characterizing composite plates. Lamb wave disperison curves and group velocities were correlated with variations in axial stiffness and shear stiffness in MMC and CMC. For CMCs, interfacial shear strength was also correlated with the first antisymmetric Lamb mode.

Detecting Lamb waves with broad-band acousto-ultrasonic signals in composite structures

NASA Technical Reports Server (NTRS)

Kautz, Harold E.

1992-01-01

Lamb waves can be produced and detected in ceramic matrix composites (CMC) and metal matrix composites (MMC) plates using the acousto-ultrasonic configuration employing broadband transducers. Experimental dispersion curves of lowest symmetric and antisymmetric modes behave in a manner analogous to the graphite/polymer theoretical curves. In this study a basis has been established for analyzing Lamb wave velocities for characterizing composite plates. Lamb wave dispersion curves and group velocities were correlated with variations in axial stiffness and shear stiffness in MMC and CMC. For CMC, interfacial shear strength was also correlated with the first antisymmetric Lamb mode.

Relationships of the group velocity of the time-reversed Lamb wave with bone properties in cortical bone in vitro.

PubMed

Lee, Kang Il; Yoon, Suk Wang

2017-04-11

The present study aims to investigate the feasibility of using the time-reversed Lamb wave as a new method for noninvasive characterization of long cortical bones. The group velocity of the time-reversed Lamb wave launched by using the modified time reversal method was measured in 15 bovine tibiae, and their correlations with the bone properties of the tibia were examined. The group velocity of the time-reversed Lamb wave showed significant positive correlations with the bone properties (r=0.55-0.81). The best univariate predictor of the group velocity of the time-reversed Lamb wave was the cortical thickness, yielding an adjusted squared correlation coefficient (r 2 ) of 0.64. These results imply that the group velocity of the time-reversed Lamb wave, in addition to the velocities of the first arriving signal and the slow guided wave, could potentially be used as a discriminator for osteoporosis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental assessment of the influence of welding process parameters on Lamb wave transmission across ultrasonically welded thermoplastic composite joints

NASA Astrophysics Data System (ADS)

Ochôa, Pedro; Fernandez Villegas, Irene; Groves, Roger M.; Benedictus, Rinze

2018-01-01

One of the advantages of thermoplastic composites relative to their thermoset counterparts is the possibility of assembling components through welding. Ultrasonic welding in particular is very promising for industrialization. However, uncertainty in the fatigue and fracture behaviour of composites is still an obstacle to the full utilisation of these materials. Health monitoring is then of vital importance, and Lamb wave techniques have been widely recognised as some of the most promising approaches for that end. This paper presents the first experimental study about the influence of welding travel on the transmission of Lamb waves across ultrasonically welded thermoplastic composite joints in single-lap configuration. The main aim of this research is to start to understand how guided waves interact with the internal structure of ultrasonic welds, so that benign, manufacturing-related structural features can be distinguished from damaging ones in signal interpretation. The power transmission coefficient and the correlation coefficient proved to be suitable for analysing the wave propagation phenomena, allowing quantitative identification of small variations of weld-line thickness and intermolecular diffusion at the weld interface. The conclusions are used to develop a tentative damage detection criterion which can later on assist the design of a Lamb wave based structural health monitoring system for thermoplastic composite structures. The Lamb wave test results are backed up by phased-array inspections, which also provide some extra insight on the internal structure of ultrasonic welds.

Using Ultrasonic Lamb Waves To Measure Moduli Of Composites

NASA Technical Reports Server (NTRS)

Kautz, Harold E.

1995-01-01

Measurements of broad-band ultrasonic Lamb waves in plate specimens of ceramic-matrix/fiber and metal-matrix/fiber composite materials used to determine moduli of elasticity of materials. In one class of potential applications of concept, Lamb-wave responses of specimens measured and analyzed at various stages of thermal and/or mechanical processing to determine effects of processing, without having to dissect specimens. In another class, structural components having shapes supporting propagation of Lamb waves monitored ultrasonically to identify signs of deterioration and impending failure.

Time-frequency energy density precipitation method for time-of-flight extraction of narrowband Lamb wave detection signals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Y., E-mail: thuzhangyu@foxmail.com; Huang, S. L., E-mail: huangsling@tsinghua.edu.cn; Wang, S.

The time-of-flight of the Lamb wave provides an important basis for defect evaluation in metal plates and is the input signal for Lamb wave tomographic imaging. However, the time-of-flight can be difficult to acquire because of the Lamb wave dispersion characteristics. This work proposes a time-frequency energy density precipitation method to accurately extract the time-of-flight of narrowband Lamb wave detection signals in metal plates. In the proposed method, a discrete short-time Fourier transform is performed on the narrowband Lamb wave detection signals to obtain the corresponding discrete time-frequency energy density distribution. The energy density values at the center frequency formore » all discrete time points are then calculated by linear interpolation. Next, the time-domain energy density curve focused on that center frequency is precipitated by least squares fitting of the calculated energy density values. Finally, the peak times of the energy density curve obtained relative to the initial pulse signal are extracted as the time-of-flight for the narrowband Lamb wave detection signals. An experimental platform is established for time-of-flight extraction of narrowband Lamb wave detection signals, and sensitivity analysis of the proposed time-frequency energy density precipitation method is performed in terms of propagation distance, dispersion characteristics, center frequency, and plate thickness. For comparison, the widely used Hilbert–Huang transform method is also implemented for time-of-flight extraction. The results show that the time-frequency energy density precipitation method can accurately extract the time-of-flight with relative error of <1% and thus can act as a universal time-of-flight extraction method for narrowband Lamb wave detection signals.« less

Time-frequency energy density precipitation method for time-of-flight extraction of narrowband Lamb wave detection signals.

PubMed

Zhang, Y; Huang, S L; Wang, S; Zhao, W

2016-05-01

The time-of-flight of the Lamb wave provides an important basis for defect evaluation in metal plates and is the input signal for Lamb wave tomographic imaging. However, the time-of-flight can be difficult to acquire because of the Lamb wave dispersion characteristics. This work proposes a time-frequency energy density precipitation method to accurately extract the time-of-flight of narrowband Lamb wave detection signals in metal plates. In the proposed method, a discrete short-time Fourier transform is performed on the narrowband Lamb wave detection signals to obtain the corresponding discrete time-frequency energy density distribution. The energy density values at the center frequency for all discrete time points are then calculated by linear interpolation. Next, the time-domain energy density curve focused on that center frequency is precipitated by least squares fitting of the calculated energy density values. Finally, the peak times of the energy density curve obtained relative to the initial pulse signal are extracted as the time-of-flight for the narrowband Lamb wave detection signals. An experimental platform is established for time-of-flight extraction of narrowband Lamb wave detection signals, and sensitivity analysis of the proposed time-frequency energy density precipitation method is performed in terms of propagation distance, dispersion characteristics, center frequency, and plate thickness. For comparison, the widely used Hilbert-Huang transform method is also implemented for time-of-flight extraction. The results show that the time-frequency energy density precipitation method can accurately extract the time-of-flight with relative error of <1% and thus can act as a universal time-of-flight extraction method for narrowband Lamb wave detection signals.

Lamb Wave Dispersion Ultrasound Vibrometry (LDUV) Method for Quantifying Mechanical Properties of Viscoelastic Solids

PubMed Central

Nenadic, Ivan Z.; Urban, Matthew W.; Mitchell, Scott A.; Greenleaf, James F.

2011-01-01

Diastolic dysfunction is the inability of the left ventricle to supply sufficient stroke volumes under normal physiological conditions and is often accompanied by stiffening of the left-ventricular myocardium. A noninvasive technique capable of quantifying viscoelasticity of the myocardium would be beneficial in clinical settings. Our group has been investigating the use of Shearwave Dispersion Ultrasound Vibrometry (SDUV), a noninvasive ultrasound based method for quantifying viscoelasticity of soft tissues. The primary motive of this study is the design and testing of viscoelastic materials suitable for validation of the Lamb wave Dispersion Ultrasound Vibrometry (LDUV), an SDUV-based technique for measuring viscoelasticity of tissues with plate-like geometry. We report the results of quantifying viscoelasticity of urethane rubber and gelatin samples using LDUV and an embedded sphere method. The LDUV method was used to excite antisymmetric Lamb waves and measure the dispersion in urethane rubber and gelatin plates. An antisymmetric Lamb wave model was fitted to the wave speed dispersion data to estimate elasticity and viscosity of the materials. A finite element model of a viscoelastic plate submerged in water was used to study the appropriateness of the Lamb wave dispersion equations. An embedded sphere method was used as an independent measurement of the viscoelasticity of the urethane rubber and gelatin. The FEM dispersion data were in excellent agreement with the theoretical predictions. Viscoelasticity of the urethane rubber and gelatin obtained using the LDUV and embedded sphere methods agreed within one standard deviation. LDUV studies on excised porcine myocardium sample were performed to investigate the feasibility of the approach in preparation for open-chest in vivo studies. The results suggest that the LDUV technique can be used to quantify mechanical properties of soft tissues with a plate-like geometry. PMID:21403186

The Simple Lamb Wave Analysis to Characterize Concrete Wide Beams by the Practical MASW Test

PubMed Central

Lee, Young Hak; Oh, Taekeun

2016-01-01

In recent years, the Lamb wave analysis by the multi-channel analysis of surface waves (MASW) for concrete structures has been an effective nondestructive evaluation, such as the condition assessment and dimension identification by the elastic wave velocities and their reflections from boundaries. This study proposes an effective Lamb wave analysis by the practical application of MASW to concrete wide beams in an easy and simple manner in order to identify the dimension and elastic wave velocity (R-wave) for the condition assessment (e.g., the estimation of elastic properties). This is done by identifying the zero-order antisymmetric (A0) and first-order symmetric (S1) modes among multimodal Lamb waves. The MASW data were collected on eight concrete wide beams and compared to the actual depth and to the pressure (P-) wave velocities collected for the same specimen. Information is extracted from multimodal Lamb wave dispersion curves to obtain the elastic stiffness parameters and the thickness of the concrete structures. Due to the simple and cost-effective procedure associated with the MASW processing technique, the characteristics of several fundamental modes in the experimental Lamb wave dispersion curves could be measured. Available reference data are in good agreement with the parameters that were determined by our analysis scheme. PMID:28773562

Harmonic generation of Lamb waves

NASA Astrophysics Data System (ADS)

Ing, Ros Kiri

2002-11-01

Lamb waves are dispersive waves that propagate following a number of distinct modes that depend on the values of the central frequency and frequency band. According to such properties and using the time-reversal process, it is shown that the hyperfocusing effect may be experienced [R. K. Ing and M. Fink, IEEE Trans. Ultrason. Ferroelectr. Freq. Control 45, 1032-1043 (1998)]. Such a focusing effect both relates the time recompression of the dispersive Lamb waves and constructive interference on the focus point of the modes involved. The hyperfocusing effect is interesting because it allows the amplitude of the Lamb waves to reach huge values on the focus point. In our experiments, Lamb waves with normal amplitudes of micrometer values have been achieved on the free surface of a Duralumin plate of 3 mm thickness. By analyzing the Lamb waves in the neighborhood of the focus point using the 2-D Fourier transform technique, a nonlinear process of harmonic generation is then observed--the fundamental frequency component is centered at 1.5 MHz. This nonlinear process is under study and quantified.

Investigating the thermally induced acoustoelastic effect in isotropic media with Lamb waves

PubMed Central

Dodson, Jacob C.; Inman, Daniel J.

2014-01-01

Elastic wave velocities in metallic structures are affected by variations in environmental conditions such as changing temperature. This paper extends the theory of acoustoelasticity by allowing thermally induced strains in unconstrained isotropic media, and it experimentally examines the velocity variation of Lamb waves in aluminum plates (AL-6061) due to isothermal temperature deviations. This paper presents both thermally induced acoustoelastic constants and thermally varying effective Young's modulus and Poisson's ratio which include the third order elastic material constants. The experimental thermal sensitivity of the phase velocity (∂vP/∂θ) for both the symmetric and antisymmetric modes are bounded by two theories, the acoustoelastic Lamb wave theory with thermo-acoustoelastic tensors and the thermoelastic Lamb wave theory using an effective thermo-acoustoelastic moduli. This paper shows the theoretical thermally induced acoustoelastic Lamb wave thermal sensitivity (∂vP/∂θ) is an upper bound approximation of the experimental thermal changes, but the acoustoelastic Lamb wave theory is not valid for predicting the antisymmetric (A0) phase velocity at low frequency-thickness values, <1.55 MHz mm for various temperatures. PMID:25373955

Defect classification in sparsity-based structural health monitoring

NASA Astrophysics Data System (ADS)

Golato, Andrew; Ahmad, Fauzia; Santhanam, Sridhar; Amin, Moeness G.

2017-05-01

Guided waves have gained popularity in structural health monitoring (SHM) due to their ability to inspect large areas with little attenuation, while providing rich interactions with defects. For thin-walled structures, the propagating waves are Lamb waves, which are a complex but well understood type of guided waves. Recent works have cast the defect localization problem of Lamb wave based SHM within the sparse reconstruction framework. These methods make use of a linear model relating the measurements with the scene reflectivity under the assumption of point-like defects. However, most structural defects are not perfect points but tend to assume specific forms, such as surface cracks or internal cracks. Knowledge of the "type" of defects is useful in the assessment phase of SHM. In this paper, we present a dual purpose sparsity-based imaging scheme which, in addition to accurately localizing defects, properly classifies the defects present simultaneously. The proposed approach takes advantage of the bias exhibited by certain types of defects toward a specific Lamb wave mode. For example, some defects strongly interact with the anti-symmetric modes, while others strongly interact with the symmetric modes. We build model based dictionaries for the fundamental symmetric and anti-symmetric wave modes, which are then utilized in unison to properly localize and classify the defects present. Simulated data of surface and internal defects in a thin Aluminum plate are used to validate the proposed scheme.

Weld quality inspection using laser-EMAT ultrasonic system and C-scan method

NASA Astrophysics Data System (ADS)

Yang, Lei; Ume, I. Charles

2014-02-01

Laser/EMAT ultrasonic technique has attracted more and more interests in weld quality inspection because of its non-destructive and non-contact characteristics. When ultrasonic techniques are used to detect welds joining relative thin plates, the dominant ultrasonic waves present in the plates are Lamb waves, which propagate all through the thickness. Traditional Time of Flight(ToF) method loses its power. The broadband nature of laser excited ultrasound plus dispersive and multi-modal characteristic of Lamb waves make the EMAT acquired signals very complicated in this situation. Challenge rises in interpreting the received signals and establishing relationship between signal feature and weld quality. In this paper, the laser/EMAT ultrasonic technique was applied in a C-scan manner to record full wave propagation field over an area close to the weld. Then the effect of weld defect on the propagation field of Lamb waves was studied visually by watching an movie resulted from the recorded signals. This method was proved to be effective to detect the presence of hidden defect in the weld. Discrete wavelet transform(DWT) was applied to characterize the acquired ultrasonic signals and ideal band-pass filter was used to isolate wave components most sensitive to the weld defect. Different interactions with the weld defect were observed for different wave components. Thus this C-Scan method, combined with DWT and ideal band-pass filter, proved to be an effective methodology to experimentally study interactions of various laser excited Lamb Wave components with weld defect. In this work, the method was demonstrated by inspecting a hidden local incomplete penetration in weld. In fact, this method can be applied to study Lamb Wave interactions with any type of structural inconsistency. This work also proposed a ideal filtered based method to effectively reduce the total experimental time.

Identification of damage in composite structures using Gaussian mixture model-processed Lamb waves

NASA Astrophysics Data System (ADS)

Wang, Qiang; Ma, Shuxian; Yue, Dong

2018-04-01

Composite materials have comprehensively better properties than traditional materials, and therefore have been more and more widely used, especially because of its higher strength-weight ratio. However, the damage of composite structures is usually varied and complicated. In order to ensure the security of these structures, it is necessary to monitor and distinguish the structural damage in a timely manner. Lamb wave-based structural health monitoring (SHM) has been proved to be effective in online structural damage detection and evaluation; furthermore, the characteristic parameters of the multi-mode Lamb wave varies in response to different types of damage in the composite material. This paper studies the damage identification approach for composite structures using the Lamb wave and the Gaussian mixture model (GMM). The algorithm and principle of the GMM, and the parameter estimation, is introduced. Multi-statistical characteristic parameters of the excited Lamb waves are extracted, and the parameter space with reduced dimensions is adopted by principal component analysis (PCA). The damage identification system using the GMM is then established through training. Experiments on a glass fiber-reinforced epoxy composite laminate plate are conducted to verify the feasibility of the proposed approach in terms of damage classification. The experimental results show that different types of damage can be identified according to the value of the likelihood function of the GMM.

Demonstration of Shear Waves, Lamb Waves, and Rayleigh Waves by Mode Conversion.

ERIC Educational Resources Information Center

Leung, W. P.

1980-01-01

Introduces an experiment that can be demonstrated in the classroom to show that shear waves, Rayleigh waves, and Lamb waves can be easily generated and observed by means of mode conversion. (Author/CS)

A Guided Wave Sensor Enabling Simultaneous Wavenumber-Frequency Analysis for Both Lamb and Shear-Horizontal Waves.

PubMed

Ren, Baiyang; Cho, Hwanjeong; Lissenden, Cliff J

2017-03-01

Guided waves in plate-like structures have been widely investigated for structural health monitoring. Lamb waves and shear horizontal (SH) waves, two commonly used types of waves in plates, provide different benefits for the detection of various types of defects and material degradation. However, there are few sensors that can detect both Lamb and SH waves and also resolve their modal content, namely the wavenumber-frequency spectrum. A sensor that can detect both waves is desirable to take full advantage of both types of waves in order to improve sensitivity to different discontinuity geometries. We demonstrate that polyvinylidene difluoride (PVDF) film provides the basis for a multi-element array sensor that detects both Lamb and SH waves and also measures their modal content, i.e., the wavenumber-frequency spectrum.

Damage assessment in composite laminates via broadband Lamb wave.

PubMed

Gao, Fei; Zeng, Liang; Lin, Jing; Shao, Yongsheng

2018-05-01

Time of flight (ToF) based method for damage detection using Lamb waves is widely used. However, due to the energy dissipation of Lamb waves and the non-ignorable size of damage in composite structure, the performance of damage detection is restricted. The objective of this research is to establish an improved method to locate and assess damages in composite structure. To choose appropriate excitation parameters, the propagation characters of Lamb waves in quasi-isotropic composite laminates are firstly studied and the broadband excitation is designed. Subsequently, the pulse compression technique is adopted for energy concentration and high-accuracy distance estimation. On this basis, the gravity center of intersections of path loci is employed for damage localization and the convex envelop of identified damage edge points is taken for damage contour estimation. As a result, both damage location and size can be evaluated, thereby providing the information for quantitative damage detection. The experiment consisting of five different sizes of damage is carried for method verification and the identified results show the efficiency of the proposed method. Copyright © 2018 Elsevier B.V. All rights reserved.

Signal Construction-Based Dispersion Compensation of Lamb Waves Considering Signal Waveform and Amplitude Spectrum Preservation

PubMed Central

Cai, Jian; Yuan, Shenfang; Wang, Tongguang

2016-01-01

The results of Lamb wave identification for the aerospace structures could be easily affected by the nonlinear-dispersion characteristics. In this paper, dispersion compensation of Lamb waves is of particular concern. Compared with the similar research works on the traditional signal domain transform methods, this study is based on signal construction from the viewpoint of nonlinear wavenumber linearization. Two compensation methods of linearly-dispersive signal construction (LDSC) and non-dispersive signal construction (NDSC) are proposed. Furthermore, to improve the compensation effect, the influence of the signal construction process on the other crucial signal properties, including the signal waveform and amplitude spectrum, is considered during the investigation. The linear-dispersion and non-dispersion effects are firstly analyzed. Then, after the basic signal construction principle is explored, the numerical realization of LDSC and NDSC is discussed, in which the signal waveform and amplitude spectrum preservation is especially regarded. Subsequently, associated with the delay-and-sum algorithm, LDSC or NDSC is employed for high spatial resolution damage imaging, so that the adjacent multi-damage or quantitative imaging capacity of Lamb waves can be strengthened. To verify the proposed signal construction and damage imaging methods, the experimental and numerical validation is finally arranged on the aluminum plates. PMID:28772366

Signal Construction-Based Dispersion Compensation of Lamb Waves Considering Signal Waveform and Amplitude Spectrum Preservation.

PubMed

Cai, Jian; Yuan, Shenfang; Wang, Tongguang

2016-12-23

The results of Lamb wave identification for the aerospace structures could be easily affected by the nonlinear-dispersion characteristics. In this paper, dispersion compensation of Lamb waves is of particular concern. Compared with the similar research works on the traditional signal domain transform methods, this study is based on signal construction from the viewpoint of nonlinear wavenumber linearization. Two compensation methods of linearly-dispersive signal construction (LDSC) and non-dispersive signal construction (NDSC) are proposed. Furthermore, to improve the compensation effect, the influence of the signal construction process on the other crucial signal properties, including the signal waveform and amplitude spectrum, is considered during the investigation. The linear-dispersion and non-dispersion effects are firstly analyzed. Then, after the basic signal construction principle is explored, the numerical realization of LDSC and NDSC is discussed, in which the signal waveform and amplitude spectrum preservation is especially regarded. Subsequently, associated with the delay-and-sum algorithm, LDSC or NDSC is employed for high spatial resolution damage imaging, so that the adjacent multi-damage or quantitative imaging capacity of Lamb waves can be strengthened. To verify the proposed signal construction and damage imaging methods, the experimental and numerical validation is finally arranged on the aluminum plates.

Study of Lamb Waves for Non-Destructive Testing Behind Screens

NASA Astrophysics Data System (ADS)

Kauffmann, P.; Ploix, M.-A.; Chaix, J.-F.; Gueudré, C.; Corneloup, G.; Baqué, F. AF(; )

2018-01-01

The inspection and control of sodium-cooled fast reactors (SFR) is a major issue for the nuclear industry. Ultrasonic solutions are under study because of the opacity of liquid sodium. In this paper, the use of leaky Lamb waves is considered for non-destructive testing (NDT) on parallel and immersed structures assimilated as plates. The first phase of our approach involved studying the propagation properties of leaky Lamb waves. Equations that model the propagation of Lamb waves in an immersed plate were solved numerically. The phase velocity can be experimentally measured using a two dimensional Fourier transform. The group velocity can be experimentally measured using a short-time Fourier transform technique. Attenuation of leaky Lamb waves is mostly due to the re-emission of energy into the surrounding fluid, and it can be measured by these two techniques.

Fatigue disbonding analysis of wide composite panels by means of Lamb waves

NASA Astrophysics Data System (ADS)

Michalcová, Lenka; Rechcígel, Lukáš; Bělský, Petr; Kucharský, Pavel

2018-03-01

Guided wave-based monitoring of composite structures plays an important role in the area of structural health monitoring (SHM) of aerospace structures. Adhesively bonded joints have not yet fulfilled current airworthiness requirements; hence, assemblies of carbon fibre-reinforced parts still require mechanical fasteners, and a verified SHM method with reliable disbonding/delamination detection and propagation assessment is needed. This study investigated the disbonding/delamination propagation in adhesively bonded panels using Lamb waves during fatigue tests. Analyses focused on the proper frequency and mode selection, sensor placement and selection of parameter sensitive to the growth of disbonding areas. Piezoelectric transducers placed across the bonded area were used as actuators and sensors. Lamb wave propagation was investigated considering the actual shape of the crack front and the mode of the crack propagation. The actual cracked area was determined by ultrasonic A-scans. A correlation between the crack propagation rate and the A0 mode velocity was found.

A guided wave sensor enabling simultaneous wavenumber-frequency analysis for both lamb and shear-horizontal waves

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ren, Baiyang; Cho, Hwanjeong; Lissenden, Cliff J.

Guided waves in plate-like structures have been widely investigated for structural health monitoring. Lamb waves and shear horizontal (SH) waves, two commonly used types of waves in plates, provide different benefits for the detection of various types of defects and material degradation. However, there are few sensors that can detect both Lamb and SH waves and also resolve their modal content, namely the wavenumber-frequency spectrum. A sensor that can detect both waves is desirable to take full advantage of both types of waves in order to improve sensitivity to different discontinuity geometries. As a result, we demonstrate that polyvinylidene difluoridemore » (PVDF) film provides the basis for a multi-element array sensor that detects both Lamb and SH waves and also measures their modal content, i.e., the wavenumber-frequency spectrum.« less

A guided wave sensor enabling simultaneous wavenumber-frequency analysis for both lamb and shear-horizontal waves

DOE PAGES

Ren, Baiyang; Cho, Hwanjeong; Lissenden, Cliff J.

2017-03-01

Guided waves in plate-like structures have been widely investigated for structural health monitoring. Lamb waves and shear horizontal (SH) waves, two commonly used types of waves in plates, provide different benefits for the detection of various types of defects and material degradation. However, there are few sensors that can detect both Lamb and SH waves and also resolve their modal content, namely the wavenumber-frequency spectrum. A sensor that can detect both waves is desirable to take full advantage of both types of waves in order to improve sensitivity to different discontinuity geometries. As a result, we demonstrate that polyvinylidene difluoridemore » (PVDF) film provides the basis for a multi-element array sensor that detects both Lamb and SH waves and also measures their modal content, i.e., the wavenumber-frequency spectrum.« less

Study of guided wave propagation on a plate between two solid bodies with imperfect contact conditions.

PubMed

Balvantín, A J; Diosdado-De-la-Peña, J A; Limon-Leyva, P A; Hernández-Rodríguez, E

2018-02-01

In this work, fundamental symmetric Lamb wave S0 mode is characterized in terms of its velocity variation as function of the interfacial conditions between solid bodies in contact. Imperfect contact conditions are numerically and experimentally determined by using ultrasonic Lamb wave propagation parameters. For the study, an experimental system was used, formed by two solid aluminum rods (25.4mm in diameter) axially loading a thin aluminum plate to control contact interfacial stiffness. The axially applied load on the aluminum plate was varied from 0MPa to 10MPa. Experimental Lamb wave signals were excited on the plate through two longitudinal contact transducers (1MHz of central frequency) using a pitch-catch configuration. Numerical simulations of contact conditions and Lamb wave propagation were performed through Finite Element Analysis (FEA) in commercial software, ANSYS 15®. Simulated Lamb wave signals were generated by means of a 5 cycles tone burst signals with different frequency values. Results indicate a velocity change in both, experimental and simulated Lamb wave signals as function of the applied load. Finally, a comparison between numerical results and experimental measurements was performed obtaining a good agreement. Copyright © 2017 Elsevier B.V. All rights reserved.

Lamb wave propagation in Z-pin reinforced co-cured composite pi-joints

NASA Astrophysics Data System (ADS)

Swenson, Eric D.; Soni, Som R.; Kapoor, Hitesh

2010-04-01

This paper presents an initial study on Lamb wave propagation characteristics in z-pin reinforced, co-cured composite pi-joints for the purposes of structural health monitoring (SHM). Pi-joint test articles were designed and created to replicate a co-cured, all composite skin-spar joint found within a typical aircraft wing structure. Because pi-joints exhibit various complex damage modes, formal studies are required if SHM systems are to be developed to monitor these types of joints for potential damage. Experiments were conducted on a undamaged (healthy) and damaged test articles where Lamb waves were excited using one lead zirconate titanate (PZT) transducer. A three-dimensional (3D) scanning laser Doppler vibrometer (LDV) was used to collect high-density scans of both the in-plane and out-of-plane velocity measurements. In the damaged test article, where delamination, matrix cracking, and fiber breakage can clearly be seen, changes in both the fundamental antisymmetric A0 and symmetric S0 Lamb wave modes are apparent. In both test articles, the effects of narrow geometry, discontinuity due to the attachment of the web, and thickness has detectable effects on Lamb wave propagation. From the comparisons between Lamb waves propagating through the undamaged and damaged test articles, it is clear that damage can be detected using Lamb waves in z-pin reinforced, co-cured composite pi-joints for this case of extensive damage.

Adverse event detection (AED) system for continuously monitoring and evaluating structural health status

NASA Astrophysics Data System (ADS)

Yun, Jinsik; Ha, Dong Sam; Inman, Daniel J.; Owen, Robert B.

2011-03-01

Structural damage for spacecraft is mainly due to impacts such as collision of meteorites or space debris. We present a structural health monitoring (SHM) system for space applications, named Adverse Event Detection (AED), which integrates an acoustic sensor, an impedance-based SHM system, and a Lamb wave SHM system. With these three health-monitoring methods in place, we can determine the presence, location, and severity of damage. An acoustic sensor continuously monitors acoustic events, while the impedance-based and Lamb wave SHM systems are in sleep mode. If an acoustic sensor detects an impact, it activates the impedance-based SHM. The impedance-based system determines if the impact incurred damage. When damage is detected, it activates the Lamb wave SHM system to determine the severity and location of the damage. Further, since an acoustic sensor dissipates much less power than the two SHM systems and the two systems are activated only when there is an acoustic event, our system reduces overall power dissipation significantly. Our prototype system demonstrates the feasibility of the proposed concept.

Temperature effects on the band gaps of Lamb waves in a one-dimensional phononic-crystal plate (L).

PubMed

Cheng, Y; Liu, X J; Wu, D J

2011-03-01

This study investigates the temperature-tuned band gaps of Lamb waves in a one-dimensional phononic-crystal plate, which is formed by alternating strips of ferroelectric ceramic Ba(0.7)Sr(0.3)TiO(3) and epoxy. The sensitive and continuous temperature-tunability of Lamb wave band gaps is demonstrated using the analyses of the band structures and the transmission spectra. The width and position of Lamb wave band gaps shift prominently with variation of temperature in the range of 26 °C-50 °C. For example, the width of the second band gap increases from 0.066 to 0.111 MHz as the temperature is increased from 26 °C to 50 °C. The strong shift promises that the structure could be suitable for temperature-tuned multi-frequency Lamb wave filters. © 2011 Acoustical Society of America

Refractive index modulation in LiNbO3: MgO slab through Lamb wave

NASA Astrophysics Data System (ADS)

Prakash, Suraj; Sharma, Gaurav; Yadav, Gulab Chand; Singh, Vivek

2018-05-01

Present theoretical analysis deals with inducing refractive index contrast in Y-Z LiNbO3:MgO plate via GHz Lamb wave perturbation for photonic applications. Dispersion curves for Lamb wave in plate are plotted by employing displacement potential technique. Selecting wave parameters from dispersion curve, fundamental symmetric Lamb mode (S0) is excited in slab for 6GHz frequency. Produced displacement field by propagating S0 mode and thus developed strain is estimated to calculate refractive index modulation by applying photo-elastic relations. Modulated refractive index is of sinusoidal nature with period of modulation dependence on Lamb's wavelength. This plate having periodically modulated refractive index can be used as photonic crystal for different applications with acoustically tunable photonic band gap.

Lamb wave line sensing for crack detection in a welded stiffener.

PubMed

An, Yun-Kyu; Kim, Jae Hong; Yim, Hong Jae

2014-07-18

This paper proposes a novel Lamb wave line sensing technique for crack detection in a welded stiffener. The proposed technique overcomes one of the biggest technical challenges of Lamb wave crack detection for real structure applications: crack-induced Lamb waves are often mixed with multiple reflections from complex waveguides. In particular, crack detection in a welded joint, one of the structural hot spots due to stress concentration, is accompanied by reflections from the welded joint as well as a crack. Extracting and highlighting crack-induced Lamb wave modes from Lamb wave responses measured at multi-spatial points along a single line can be accomplished through a frequency-wavenumber domain analysis. The advantages of the proposed technique enable us not only to enhance the crack detectability in the welded joint but also to minimize false alarms caused by environmental and operational variations by avoiding the direct comparison with the baseline data previously accumulated from the pristine condition of a target structure. The proposed technique is experimentally and numerically validated in vertically stiffened metallic structures, revealing that it successfully identifies and localizes subsurface cracks, regardless of the coexistence with the vertical stiffener.

High spatial resolution imaging for structural health monitoring based on virtual time reversal

NASA Astrophysics Data System (ADS)

Cai, Jian; Shi, Lihua; Yuan, Shenfang; Shao, Zhixue

2011-05-01

Lamb waves are widely used in structural health monitoring (SHM) of plate-like structures. Due to the dispersion effect, Lamb wavepackets will be elongated and the resolution for damage identification will be strongly affected. This effect can be automatically compensated by the time reversal process (TRP). However, the time information of the compensated waves is also removed at the same time. To improve the spatial resolution of Lamb wave detection, virtual time reversal (VTR) is presented in this paper. In VTR, a changing-element excitation and reception mechanism (CERM) rather than the traditional fixed excitation and reception mechanism (FERM) is adopted for time information conservation. Furthermore, the complicated TRP procedure is replaced by simple signal operations which can make savings in the hardware cost for recording and generating the time-reversed Lamb waves. After the effects of VTR for dispersive damage scattered signals are theoretically analyzed, the realization of VTR involving the acquisition of the transfer functions of damage detecting paths under step pulse excitation is discussed. Then, a VTR-based imaging method is developed to improve the spatial resolution of the delay-and-sum imaging with a sparse piezoelectric (PZT) wafer array. Experimental validation indicates that the damage scattered wavepackets of A0 mode in an aluminum plate are partly recompressed and focalized with their time information preserved by VTR. Both the single damage and the dual adjacent damages in the plate can be clearly displayed with high spatial resolution by the proposed VTR-based imaging method.

A micromachined thermally compensated thin film Lamb wave resonator for frequency control and sensing applications

NASA Astrophysics Data System (ADS)

Wingqvist, G.; Arapan, L.; Yantchev, V.; Katardjiev, I.

2009-03-01

Micromachined thin film plate acoustic wave resonators (FPARs) utilizing the lowest order symmetric Lamb wave (S0) propagating in highly textured 2 µm thick aluminium nitride (AlN) membranes have been successfully demonstrated (Yantchev and Katardjiev 2007 IEEE Trans. Ultrason. Ferroelectr. Freq. Control 54 87-95). The proposed devices have a SAW-based design and exhibit Q factors of up to 3000 at a frequency around 900 MHz as well as design flexibility with respect to the required motional resistance. However, a notable drawback of the proposed devices is the non-zero temperature coefficient of frequency (TCF) which lies in the range -20 ppm K-1 to -25 ppm K-1. Thus, despite the promising features demonstrated, further device optimization is required. In this work temperature compensation of thin AlN film Lamb wave resonators is studied and experimentally demonstrated. Temperature compensation while retaining at the same time the device electromechanical coupling is experimentally demonstrated. The zero TCF Lamb wave resonators are fabricated onto composite AlN/SiO2 membranes. Q factors of around 1400 have been measured at a frequency of around 755 MHz. Finally, the impact of technological issues on the device performance is discussed in view of improving the device performance.

Multimodal sparse reconstruction in guided wave imaging of defects in plates

NASA Astrophysics Data System (ADS)

Golato, Andrew; Santhanam, Sridhar; Ahmad, Fauzia; Amin, Moeness G.

2016-07-01

A multimodal sparse reconstruction approach is proposed for localizing defects in thin plates in Lamb wave-based structural health monitoring. The proposed approach exploits both the sparsity of the defects and the multimodal nature of Lamb wave propagation in plates. It takes into account the variation of the defects' aspect angles across the various transducer pairs. At low operating frequencies, only the fundamental symmetric and antisymmetric Lamb modes emanate from a transmitting transducer. Asymmetric defects scatter these modes and spawn additional converted fundamental modes. Propagation models are developed for each of these scattered and spawned modes arriving at the various receiving transducers. This enables the construction of modal dictionary matrices spanning a two-dimensional array of pixels representing potential defect locations in the region of interest. Reconstruction of the region of interest is achieved by inverting the resulting linear model using the group sparsity constraint, where the groups extend across the various transducer pairs and the different modes. The effectiveness of the proposed approach is established with finite-element scattering simulations of the fundamental Lamb wave modes by crack-like defects in a plate. The approach is subsequently validated with experimental results obtained from an aluminum plate with asymmetric defects.

Rectification of Lamb wave propagation in thin plates with piezo-dielectric periodic structures

NASA Astrophysics Data System (ADS)

Iwasaki, Yuhei; Tsuruta, Kenji; Ishikawa, Atsushi

2016-07-01

Based on a heterostructured plate consisting of piezoelectric-ceramic/epoxy-resin composites with different periodicities, we design a novel acoustic diode for the symmetrical/asymmetrical (S/A) mode of Lamb wave at audible ranges. The acoustic diode is constructed with two parts, i.e., the mode conversion part and the mode selection part, and the mode conversion mechanism at the interface is applied to the mode hybridization from S to S+A and for the mode conversion from A to S. The phonon band structures for each part are calculated and optimized so that the mode selection is realized for a specific mode at the junction. Finite-element simulations prove that the proposed acoustic diode achieves efficient rectification at audio frequency ranges for both S and A mode incidences of the Lamb wave.

Application of the Pseudo Wigner-Ville Distribution to the Measurement of the Dispersion of Lamb Modes in Graphite/Epoxy Plates

NASA Technical Reports Server (NTRS)

Prosser, W. H.; Seale, M. D.; Smith, B. T.

1997-01-01

Acoustic waves propagate in thin plates as guided or Lamb modes. The velocities of these modes are dispersive in that they depend not only on the material elastic properties and density, but also on the frequency. Accurate characterization of Lamb wave dispersion is important in many acoustic based nondestructive evaluation techniques. It is necessary for ultrasonic measurements in thin plates to determine elastic properties and for flaw detection and localization. In acoustic emission (AE) testing, if not taken into account, highly dispersive Lamb mode propagation can lead to large errors in source location. In this study, the pseudo Wigner-Ville distribution (PWVD) was used for measurement of group velocity dispersion of Lamb waves in a unidirectional graphite/epoxy (AS4/3502) laminate. The PWVD is one of a number of transforms which provide a time-frequency representation of a digitized time series. Broad band acoustic waves were generated by a pencil lead fracture (Hsu-Neilsen source) and were detected with broad band ultrasonic transducers. The arrival times for the lowest order symmetric (S(sub 0)) and antisymmetric (A(sub 0)) Lamb modes were determined from measurements of the time at which the respective peak amplitudes occurred in the PWVD. Measurements were made at several source-to-detector distances and a least squares fit used to calculate the velocity. Results are presented for propagation along, and perpendicular to, the fiber direction. Theoretical dispersion curves were also calculated and a comparison between theory and experiment demonstrates good agreement.

Ultrasonic technique for inspection of GPHS capsule girth weld integrity

NASA Astrophysics Data System (ADS)

Placr, Arnost

1993-05-01

An innovative nondestructive examination (NDE) technique for the inspection of integrity of General Purpose Heat Source (GPHS) capsule girth welds was developed employing a Lamb wave as the mode of the sound propagation. Reliability of the Lamb wave technique was tested on GPHS capsules using plutonium pallet simulators. All ten capsules, which were previously rejected, passed ultrasonic (UT) inspection using the Lamb wave technique.

Improved ultrasonic TV images achieved by use of Lamb-wave orientation technique

NASA Technical Reports Server (NTRS)

Berger, H.

1967-01-01

Lamb-wave sample orientation technique minimizes the interference from standing waves in continuous wave ultrasonic television imaging techniques used with thin metallic samples. The sample under investigation is oriented such that the wave incident upon it is not normal, but slightly angled.

Unusual energy properties of leaky backward Lamb waves in a submerged plate.

PubMed

Nedospasov, I A; Mozhaev, V G; Kuznetsova, I E

2017-05-01

It is found that leaky backward Lamb waves, i.e. waves with negative energy-flux velocity, propagating in a plate submerged in a liquid possess extraordinary energy properties distinguishing them from any other type of waves in isotropic media. Namely, the total time-averaged energy flux along the waveguide axis is equal to zero for these waves due to opposite directions of the longitudinal energy fluxes in the adjacent media. This property gives rise to the fundamental question of how to define and calculate correctly the energy velocity in such an unusual case. The procedure of calculation based on incomplete integration of the energy flux density over the plate thickness alone is applied. The derivative of the angular frequency with respect to the wave vector, usually referred to as the group velocity, happens to be close to the energy velocity defined by this mean in that part of the frequency range where the backward mode exists in the free plate. The existence region of the backward mode is formally increased for the submerged plate in comparison to the free plate as a result of the liquid-induced hybridization of propagating and nonpropagating (evanescent) Lamb modes. It is shown that the Rayleigh's principle (i.e. equipartition of total time-averaged kinetic and potential energies for time-harmonic acoustic fields) is violated due to the leakage of Lamb waves, in spite of considering nondissipative media. Copyright © 2017 Elsevier B.V. All rights reserved.

Theoretical investigation of Lamb wave characteristics in AlN/3C-SiC composite membranes

NASA Astrophysics Data System (ADS)

Lin, Chih-Ming; Chen, Yung-Yu; Pisano, Albert P.

2010-11-01

Cubic silicon carbide (3C-SiC) layer can provide advantages of high frequency and high quality factor for Lamb wave devices due to the superior properties of high acoustic velocity and low acoustic loss. In this study, Lamb wave propagation characteristics in composite membranes consisting of a c-axis oriented aluminum nitride (AlN) film and an epitaxial 3C-SiC (100) layer are investigated by theoretical calculation. The lowest symmetric mode Lamb wave propagating along the [011] direction exhibits a phase velocity higher than 10 000 m/s and an electromechanical coupling coefficient above 2% in the AlN/3C-SiC multilayered membranes.

Lamb wave characterization of the effects of long-term thermal-mechanical aging on composite stiffness

NASA Technical Reports Server (NTRS)

Seale, M. D.; Madaras, E. I.

1999-01-01

Lamb waves offer a promising method of evaluating damage in composite materials. The Lamb wave velocity is directly related to the material parameters, so an effective tool exists to monitor damage in composites by measuring the velocity of these waves. The Lamb Wave Imager (LWI) uses a pulse/receive technique that excites an antisymmetric Lamb mode and measures the time-of-flight over a wide frequency range. Given the material density and plate thickness, the bending and out-of-plane shear stiffnesses are calculated from a reconstruction of the dispersion curve. In this study, the time-of-flight as well as the elastic stiffnesses D11, D22, A44, and A55 for composite samples which have undergone combined thermal and mechanical aging are obtained. The samples examined include a baseline specimen with 0 cycles, specimens which have been aged 2350 and 3530 cycles at high strain levels, and one specimen aged 3530 cycles at low strain levels.

Lamb wave characterization of the effects of long-term thermal-mechanical aging on composite stiffness.

PubMed

Seale, M D; Madaras, E I

1999-09-01

Lamb waves offer a promising method of evaluating damage in composite materials. The Lamb wave velocity is directly related to the material parameters, so an effective tool exists to monitor damage in composites by measuring the velocity of these waves. The Lamb Wave Imager (LWI) uses a pulse/receive technique that excites an antisymmetric Lamb mode and measures the time-of-flight over a wide frequency range. Given the material density and plate thickness, the bending and out-of-plane shear stiffnesses are calculated from a reconstruction of the dispersion curve. In this study, the time-of-flight as well as the elastic stiffnesses D11, D22, A44, and A55 for composite samples which have undergone combined thermal and mechanical aging are obtained. The samples examined include a baseline specimen with 0 cycles, specimens which have been aged 2350 and 3530 cycles at high strain levels, and one specimen aged 3530 cycles at low strain levels.

Lamb waves increase sensitivity in nondestructive testing

NASA Technical Reports Server (NTRS)

Di Novi, R.

1967-01-01

Lamb waves improve sensitivity and resolution in the detection of small defects in thin plates and small diameter, thin-walled tubing. This improvement over shear waves applies to both longitudinal and transverse flaws in the specimens.

Topological valley-chiral edge states of Lamb waves in elastic thin plates

NASA Astrophysics Data System (ADS)

Wang, Jian; Mei, Jun

2018-05-01

We investigate the nontrivial topology of the band structure of Lamb waves in a thin phononic crystal plate. When inversion symmetry is broken, a valley pseudospin degree of freedom is formed around K and K‧ valleys for the A0 Lamb mode, which is decoupled from the S0 and SH0 modes in the low-frequency regime. Chiral edge states are explicitly demonstrated, which are immune to defects and exhibit unidirectional transport behaviors when intervalley scattering is weak. The quantum valley Hall effect is thus simulated in a simple way in the context of Lamb waves.

Symmetry properties of second harmonics generated by antisymmetric Lamb waves

NASA Astrophysics Data System (ADS)

Zhu, Wujun; Xiang, Yanxun; Liu, Chang-Jun; Deng, Mingxi; Xuan, Fu-Zhen

2018-03-01

Symmetry properties of second harmonics generated by antisymmetric primary Lamb waves are systematically studied in this work. In theory, the acoustic field of second harmonic Lamb waves is obtained by using the perturbation approximation and normal modal method, and the energy flux transfer from the primary Lamb waves to second harmonics is mainly explored. Symmetry analyses indicate that either the symmetric or antisymmetric Lamb waves can merely generate the symmetric second harmonics. Finite element simulations are performed on the nonlinear Lamb wave propagation of the antisymmetric A0 mode in the low frequency region. The signals of the second harmonics and the symmetric second harmonic s0 mode are found to be exactly equivalent in the time domain. The relative acoustic nonlinearity parameter A2/A12 oscillates with the propagation distance, and the oscillation amplitude and spatial period are well consistent with the theoretical prediction of the A0-s0 mode pair, which means that only the second harmonic s0 mode is generated by the antisymmetric primary A0 mode. Experiments are further conducted to examine the cumulative generation of symmetric second harmonics for the antisymmetric-symmetric mode pair A3-s6. Results show that A2/A12 increases linearly with the propagation distance, which means that the symmetric second harmonic s6 mode is generated cumulatively by the antisymmetric primary A3 mode. The present investigation systematically corroborates the proposed theory that only symmetric second harmonics can be generated accompanying the propagation of antisymmetric primary Lamb waves in a plate.

Real-Time Characterization of Materials Degradation Using Leaky Lamb Wave

NASA Technical Reports Server (NTRS)

Shiuh, S.; Bar-Cohen, Y.

1997-01-01

Leaky Lamb wave (LLW) propagation in composite materials has been studied extensively since it was first observed in 1982. The wave is induced using a pitch-catch arrangement and the plate wave modes are detected by searching minima in the reflected spectra.

Impact induced damage assessment by means of Lamb wave image processing

NASA Astrophysics Data System (ADS)

Kudela, Pawel; Radzienski, Maciej; Ostachowicz, Wieslaw

2018-03-01

The aim of this research is an analysis of full wavefield Lamb wave interaction with impact-induced damage at various impact energies in order to find out the limitation of the wavenumber adaptive image filtering method. In other words, the relation between impact energy and damage detectability will be shown. A numerical model based on the time domain spectral element method is used for modeling of Lamb wave propagation and interaction with barely visible impact damage in a carbon-epoxy laminate. Numerical studies are followed by experimental research on the same material with an impact damage induced by various energy and also a Teflon insert simulating delamination. Wavenumber adaptive image filtering and signal processing are used for damage visualization and assessment for both numerical and experimental full wavefield data. It is shown that it is possible to visualize and assess the impact damage location, size and to some extent severity by using the proposed technique.

Lamb waves in phononic crystal slabs with square or rectangular symmetries

NASA Astrophysics Data System (ADS)

Brunet, Thomas; Vasseur, Jérôme; Bonello, Bernard; Djafari-Rouhani, Bahram; Hladky-Hennion, Anne-Christine

2008-08-01

We report on both numerical and experimental results showing the occurrence of band gaps for Lamb waves propagating in phononic crystal plates. The structures are made of centered rectangular and square arrays of holes drilled in a silicon plate. A supercell plane wave expansion method is used to calculate the band structures and to predict the position and the magnitude of the gaps. The band structures of phononic crystal slabs are then measured using a laser ultrasonic technique. Lamb waves in the megahertz range and with wave vectors ranging over more than the first two reduced Brillouin zones are investigated.

Theoretical study on the dispersion curves of Lamb waves in piezoelectric-semiconductor sandwich plates GaAs-FGPM-AlAs: Legendre polynomial series expansion

NASA Astrophysics Data System (ADS)

Othmani, Cherif; Takali, Farid; Njeh, Anouar

2017-06-01

In this paper, the propagation of the Lamb waves in the GaAs-FGPM-AlAs sandwich plate is studied. Based on the orthogonal function, Legendre polynomial series expansion is applied along the thickness direction to obtain the Lamb dispersion curves. The convergence and accuracy of this polynomial method are discussed. In addition, the influences of the volume fraction p and thickness hFGPM of the FGPM middle layer on the Lamb dispersion curves are developed. The numerical results also show differences between the characteristics of Lamb dispersion curves in the sandwich plate for various gradient coefficients of the FGPM middle layer. In fact, if the volume fraction p increases the phase velocity will increases and the number of modes will decreases at a given frequency range. All the developments performed in this paper were implemented in Matlab software. The corresponding results presented in this work may have important applications in several industry areas and developing novel acoustic devices such as sensors, electromechanical transducers, actuators and filters.

A pulse coding and decoding strategy to perform Lamb wave inspections using simultaneously multiple actuators

NASA Astrophysics Data System (ADS)

De Marchi, Luca; Marzani, Alessandro; Moll, Jochen; Kudela, Paweł; Radzieński, Maciej; Ostachowicz, Wiesław

2017-07-01

The performance of Lamb wave based monitoring systems, both in terms of diagnosis time and data complexity, can be enhanced by increasing the number of transducers used to actuate simultaneously the guided waves in the inspected medium. However, in case of multiple simultaneously-operated actuators the interference among the excited wave modes within the acquired signals has to be considered for the further processing. To this aim, in this work a code division strategy based on the Warped Frequency Transform is presented. At first, the proposed procedure encodes actuation pulses using Gold sequences. Next, for each considered actuator the acquired signals are compensated from dispersion by cross correlating the warped version of the actuated and received signals. Compensated signals form the base for a final wavenumber imaging meant at emphasizing defects and or anomalies by removing incident wavefield and edge reflections. The proposed strategy is tested numerically, and validated through an experiment in which guided waves are actuated in a plate by four piezoelectric transducers operating simultaneously.

Effect of Prestresses on the Dispersion of Quasi-Lamb Waves in the System Consisting of an Ideal Liquid Layer and a Compressible Elastic Layer

NASA Astrophysics Data System (ADS)

Bagno, A. M.

2017-03-01

The propagation of quasi-Lamb waves in a prestrained compressible elastic layer interacting with a layer of an ideal compressible fluid is studied. The three-dimensional equations of linearized elasticity and the assumption of finite strains for the elastic layer and the three-dimensional linearized Euler equations for the fluid are used. The dispersion curves for the quasi-Lamb modes are plotted over a wide frequency range. The effect of prestresses and the thickness of the elastic and liquid layers on the frequency spectrum of normal quasi-Lamb waves is analyzed. The localization properties of the lower quasi-Lamb modes in the elastic-fluid waveguides are studied. The numerical results are presented in the form of graphs and analyzed

Load-Differential Imaging for Detection and Localization of Fatigue Cracks Using Lamb Waves (Preprint)

DTIC Science & Technology

2012-03-01

AFRL-RX-WP-TP-2012-0278 LOAD-DIFFERENTIAL IMAGING FOR DETECTION AND LOCALIZATION OF FATIGUE CRACKS USING LAMB WAVES (PREPRINT) X. Chen...OF FATIGUE CRACKS USING LAMB WAVES (PREPRINT) 5a. CONTRACT NUMBER FA8650-09-C-5206 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62102F 6...Jan 2012. Preprint journal article to be submitted to NDT & E. This document contains color. 14. ABSTRACT Fatigue cracks are common and

Defect Detection on Carbon Fibre Reinforced Plastics (cfrp) with Laser Generated Lamb Waves

NASA Astrophysics Data System (ADS)

Focke, O.; Huke, P.; Hildebrandt, A.

2011-06-01

Standard ultrasound methods using a phased-array or a single transducer are commonly used for non-destructive evaluation (NDE) during manufacturing of carbon fiber reinforced plastics (CFRP) parts and certificated testing schemes were developed for individual parts and geometries. However, most testing methods need direct contact, matching gels and remain therefore time consuming. Laser-Ultrasonics is advantageous due to the contactless measurement technology and high accessibility even on complex parts. Despite the non-destructive testing with body waves, we show that the NDE can be expanded using two-dimensional surface (Lamb) waves for detection of delaminations close to the surface or small deteriorations caused by e.g. impacts. Lamb waves have been excited with a single transducer and with a short-pulse Laser with additionally producing A0-and S0-Lamb waves. The waves were detected with a shearography setup that allows for measuring two-dimensionally the displacement of a surface. Short integration times of the camera were realized using a pulsed ruby laser for illumination. As a consequence to the anisotropy the propagation in different directions exhibits individual characteristics like amplitude, damping and velocity. This has motivated to build up models for the propagation of Lamb waves and to compare them with experimental results.

Measurement of leaky Lamb wave dispersion curves with application on coating characterization

NASA Astrophysics Data System (ADS)

Lee, Yung-Chun; Cheng, Sheng Wen

2001-04-01

This paper describes a new measurement system for measuring dispersion curves of leaky Lamb waves. The measurement system is based on a focusing PVDF transducer, the defocusing measurement, the V(f,z) waveform processing method, and an image displaying technique. The measurement system is applied for the determination of thin-film elastic properties, namely Young's modulus and shear modulus, by the inversion of dispersion curves measured from a thin-film/plate configuration. Elastic constants of electro-deposited nickel layers are determined with this method.

Location identification of closed crack based on Duffing oscillator transient transition

NASA Astrophysics Data System (ADS)

Liu, Xiaofeng; Bo, Lin; Liu, Yaolu; Zhao, Youxuan; Zhang, Jun; Deng, Mingxi; Hu, Ning

2018-02-01

The existence of a closed micro-crack in plates can be detected by using the nonlinear harmonic characteristics of the Lamb wave. However, its location identification is difficult. By considering the transient nonlinear Lamb under the noise interference, we proposed a location identification method for the closed crack based on the quantitative measurement of Duffing oscillator transient transfer in the phase space. The sliding short-time window was used to create a window truncation of to-be-detected signal. And then, the periodic extension processing for transient nonlinear Lamb wave was performed to ensure that the Duffing oscillator has adequate response time to reach a steady state. The transient autocorrelation method was used to reduce the occurrence of missed harmonic detection due to the random variable phase of nonlinear Lamb wave. Moreover, to overcome the deficiency in the quantitative analysis of Duffing system state by phase trajectory diagram and eliminate the misjudgment caused by harmonic frequency component contained in broadband noise, logic operation method of oscillator state transition function based on circular zone partition was adopted to establish the mapping relation between the oscillator transition state and the nonlinear harmonic time domain information. Final state transition discriminant function of Duffing oscillator was used as basis for identifying the reflected and transmitted harmonics from the crack. Chirplet time-frequency analysis was conducted to identify the mode of generated harmonics and determine the propagation speed. Through these steps, accurate position identification of the closed crack was achieved.

Real-time nondestructive evaluation of fiber composite laminates using low-frequency Lamb waves

NASA Astrophysics Data System (ADS)

díAz Valdés, Sergio H.; Soutis, Costas

2002-05-01

Amid the nondestructive evaluation techniques available for the inspection of composite materials, only a few are suitable for implementation while the component is in service. The investigation examines the application of Lamb waves at low-frequency-thickness products for the detection of delaminations in thick composite laminates. Surface-mounted piezoelectric devices were excited with a tone burst to generate elastic waves in the structure. Experiments were carried out on composite beam specimens where wave propagation distances over 2 m were achieved and artificially induced delaminations as small as 1 cm2 were successfully identified. The feasibility of employing piezoelectric devices for the development of smart structures, where a small and lightweight transducer system design is required, has been demonstrated. The resonance spectrum method, which is based on the study of spectra obtained by forced mechanical resonance of samples using sine-sweep excitation, has been proposed as a technique for measuring the Ao Lamb mode phase velocity. The finite-element method was also used to investigate qualitatively the dynamic response of laminates to wave propagation. Several locations and spatial distribution of the actuators were examined showing the advantages of using transducers arrays for the inspection of large structures.

Detection of crack in thin cylindrical pipes using piezo-actuated Lamb waves

NASA Astrophysics Data System (ADS)

Tua, P. S.; Quek, S. T.; Wang, Q.

2005-05-01

The detection of cracks in beams and plates using piezo-actuated Lamb waves has been presented in the last SPIE Symposium. This paper is an extension of the technique to pipes. It has been shown that for a thin-walled pipe, the assumption of Lamb wave propagation is valid. Such waves can be efficiently excited using piezoceramic transducers (PZT) with good control on the pulse characteristics to assess the health of structural components, such as the presence of cracks. In this paper, a systematic methodology to detect and locate cracks in homogenous cylinder/pipe based on the time-of-flight and strength analysis of propagating Lamb wave is proposed. By observing the attenuation in strength of the direct wave incidence at the sensor, the presence of a crack along the propagation path can be determined. At least four actuation positions, two on each end of the pipe segment of interest, are needed to exhaustively interrogate for the presence of cracks. The detailed procedure for locating and tracing the geometry of the crack(s) is described. It is shown experimentally that the detection using circular PZT actuator and sensor, with dimensions of 5.0 mm diameter and 0.5 mm thick, is possible for an aluminum pipe segment of up to at least 4.0 m in length. The proposed methodology is also explored for the aluminum pipe under more practical situations, such as burying it in sand with only the actuator and sensor positions exposed. Experimental results obtained showed the feasibility of detecting the 'concealed' crack on the pipe buried in sand.

Lamb-type waves generated by a cylindrical bubble oscillating between two planar elastic walls

PubMed Central

Mekki-Berrada, F.; Thibault, P.; Marmottant, P.

2016-01-01

The volume oscillation of a cylindrical bubble in a microfluidic channel with planar elastic walls is studied. Analytical solutions are found for the bulk scattered wave propagating in the fluid gap and the surface waves of Lamb-type propagating at the fluid–solid interfaces. This type of surface wave has not yet been described theoretically. A dispersion equation for the Lamb-type waves is derived, which allows one to evaluate the wave speed for different values of the channel height h. It is shown that for h<λt, where λt is the wavelength of the transverse wave in the walls, the speed of the Lamb-type waves decreases with decreasing h, while for h on the order of or greater than λt, their speed tends to the Scholte wave speed. The solutions for the wave fields in the elastic walls and in the fluid are derived using the Hankel transforms. Numerical simulations are carried out to study the effect of the surface waves on the dynamics of a bubble confined between two elastic walls. It is shown that its resonance frequency can be up to 50% higher than the resonance frequency of a similar bubble confined between two rigid walls. PMID:27274695

Lamb wave dispersion and anisotropy profiling of composite plates via non-contact air-coupled and laser ultrasound

NASA Astrophysics Data System (ADS)

Harb, M. S.; Yuan, F. G.

2015-03-01

Conventional ultrasound inspection has been a standard non-destructive testing method for providing an in-service evaluation and noninvasive means of probing the interior of a structure. In particular, measurement of the propagation characteristics of Lamb waves allows inspection of plates that are typical components in aerospace industry. A rapid, complete non-contact hybrid approach for excitation and detection of Lamb waves is presented and applied for non-destructive evaluation of composites. An air-coupled transducer (ACT) excites ultrasonic waves on the surface of a composite plate, generating different propagating Lamb wave modes and a laser Doppler vibrometer (LDV) is used to measure the out-of-plane velocity of the plate. This technology, based on direct waveform imaging, focuses on measuring dispersive curves for A0 mode in a composite laminate and its anisotropy. A two-dimensional fast Fourier transform (2D-FFT) is applied to out-of-plane velocity data captured experimentally using LDV to go from the time-spatial domain to frequency-wavenumber domain. The result is a 2D array of amplitudes at discrete frequencies and wavenumbers for A0 mode in a given propagation direction along the composite. The peak values of the curve are then used to construct frequency wavenumber and phase velocity dispersion curves, which are also obtained directly using Snell's law and the incident angle of the excited ultrasonic waves. A high resolution and strong correlation between numerical and experimental results are observed for dispersive curves with Snell's law method in comparison to 2D-FFT method. Dispersion curves as well as velocity curves for the composite plate along different directions of wave propagation are measured. The visual read-out of the dispersion curves at different propagation directions as well as the phase velocity curves provide profiling and measurements of the composite anisotropy. The results proved a high sensitivity of the air-coupled and laser ultrasound technique in non-contact characterization of Lamb wave dispersion and material anisotropy of composite plates using simple Snell's law method.

Excitation of plane Lamb wave in plate-like structures under applied surface loading

NASA Astrophysics Data System (ADS)

Zhou, Kai; Xu, Xinsheng; Zhao, Zhen; Yang, Zhengyan; Zhou, Zhenhuan; Wu, Zhanjun

2018-02-01

Lamb waves play an important role in structure health monitoring (SHM) systems. The excitation of Lamb waves has been discussed for a long time with absorbing results. However, little effort has been made towards the precise characterization of Lamb wave excitation by various transducer models with mathematical foundation. In this paper, the excitation of plane Lamb waves with plane strain assumption in isotropic plate structures under applied surface loading is solved with the Hamiltonian system. The response of the Lamb modes excited by applied loading is expressed analytically. The effect of applied loading is divided into the product of two parts as the effect of direction and the effect of distribution, which can be changed by selecting different types of transducer and the corresponding transducer configurations. The direction of loading determines the corresponding displacement of each mode. The effect of applied loading on the in-plane and normal directions depends on the in-plane and normal displacements at the surface respectively. The effect of the surface loading distribution on the Lamb mode amplitudes is mainly reflected by amplitude versus frequency or wavenumber. The frequencies at which the maxima and minima of the S0 or A0 mode response occur depend on the distribution of surface loading. The numerical results of simulations conducted on an infinite aluminum plate verify the theoretical prediction of not only the direction but also the distribution of applied loading. A pure S0 or A0 mode can be excited by selecting the appropriate direction and distribution at the corresponding frequency.

Second harmonic generation at fatigue cracks by low-frequency Lamb waves: Experimental and numerical studies

NASA Astrophysics Data System (ADS)

Yang, Yi; Ng, Ching-Tai; Kotousov, Andrei; Sohn, Hoon; Lim, Hyung Jin

2018-01-01

This paper presents experimental and theoretical analyses of the second harmonic generation due to non-linear interaction of Lamb waves with a fatigue crack. Three-dimensional (3D) finite element (FE) simulations and experimental studies are carried out to provide physical insight into the mechanism of second harmonic generation. The results demonstrate that the 3D FE simulations can provide a reasonable prediction on the second harmonic generated due to the contact nonlinearity at the fatigue crack. The effect of the wave modes on the second harmonic generation is also investigated in detail. It is found that the magnitude of the second harmonic induced by the interaction of the fundamental symmetric mode (S0) of Lamb wave with the fatigue crack is much higher than that by the fundamental anti-symmetric mode (A0) of Lamb wave. In addition, a series of parametric studies using 3D FE simulations are conducted to investigate the effect of the fatigue crack length to incident wave wavelength ratio, and the influence of the excitation frequency on the second harmonic generation. The outcomes show that the magnitude and directivity pattern of the generated second harmonic depend on the fatigue crack length to incident wave wavelength ratio as well as the ratio of S0 to A0 incident Lamb wave amplitude. In summary, the findings of this study can further advance the use of second harmonic generation in damage detection.

Lamb wave tomographic imaging system for aircraft structural health assessment

NASA Astrophysics Data System (ADS)

Schwarz, Willi G.; Read, Michael E.; Kremer, Matthew J.; Hinders, Mark K.; Smith, Barry T.

1999-01-01

A tomographic imaging system using ultrasonic Lamb waves for the nondestructive inspection of aircraft components such as wings and fuselage is being developed. The computer-based system provides large-area inspection capability by electronically scanning an array of transducers that can be easily attached to flat and curved surface without moving parts. Images of the inspected area are produced in near real time employing a tomographic reconstruction method adapted from seismological applications. Changes in material properties caused by structural flaws such as disbonds, corrosion, and fatigue cracks can be effectively detected and characterized utilizing this fast NDE technique.

Effect of Liquid Viscosity on Dispersion of Quasi-Lamb Waves in an Elastic-Layer-Viscous-Liquid-Layer System

NASA Astrophysics Data System (ADS)

Guz, A. N.; Bagno, A. M.

2017-07-01

The dispersion curves are constructed and propagation of quasi-Lamb waves are studied for wide range of frequencies based on the Navier -Stokes three-dimensional linearized equations for a viscous liquid and linear equations of the classical theory of elasticity for an elastic layer. For a thick liquid layer, the effect of the viscosity of the liquid and the thickness of elastic and liquid layers on the phase velocities and attenuation coefficients of quasi-Lamb modes is analyzed. It is shown that in the case of a thick liquid layer for all modes, there are elastic layers of certain thickness with minimal effect of liquid viscosity on the phase velocities and attenuation coefficients of modes. It is also discovered that for some modes, there are both certain thicknesses and certain ranges of thickness where the effect of liquid viscosity on the phase velocities and attenuation coefficients of these modes is considerable. We ascertain that liquid viscosity promotes decrease of the penetration depth of the lowest quasi-Lamb mode into the liquid. The developed approach and the obtained results make it possible to ascertain for wave processes the limits of applicability of the model of ideal compressible fluid. Numerical results in the form of graphs are adduced and analyzed.

Fast Lamb wave energy shift approach using fully contactless ultrasonic system to characterize concrete structures

NASA Astrophysics Data System (ADS)

Ham, Suyun; Popovics, John S.

2015-03-01

Ultrasonic techniques provide an effective non-destructive evaluation (NDE) method to monitor concrete structures, but the need to perform rapid and accurate structural assessment requires evaluation of hundreds, or even thousands, of measurement datasets. Use of a fully contactless ultrasonic system can save time and labor through rapid implementation, and can enable automated and controlled data acquisition, for example through robotic scanning. Here we present results using a fully contactless ultrasonic system. This paper describes our efforts to develop a contactless ultrasonic guided wave NDE approach to detect and characterize delamination defects in concrete structures. The developed contactless sensors, controlled scanning system, and employed Multi-channel Analysis of Surface Waves (MASW) signal processing scheme are reviewed. Then a guided wave interpretation approach for MASW data is described. The presence of delamination is interpreted by guided plate wave (Lamb wave) behavior, where a shift in excited Lamb mode phase velocity, is monitored. Numerically simulated and experimental ultrasonic data collected from a concrete sample with simulated delamination defects are presented, where the occurrence of delamination is shown to be associated with a mode shift in Lamb wave energy.

Evaluation of barely visible indentation damage (BVID) in CF/EP sandwich composites using guided wave signals

NASA Astrophysics Data System (ADS)

Mustapha, Samir; Ye, Lin; Dong, Xingjian; Alamdari, Mehrisadat Makki

2016-08-01

Barely visible indentation damage after quasi-static indentation in sandwich CF/EP composites was assessed using ultrasonic guided wave signals. Finite element analyses were conducted to investigate the interaction between guided waves and damage, further to assist in the selection process of the Lamb wave sensitive modes for debonding identification. Composite sandwich beams and panels structures were investigated. Using the beam structure, a damage index was defined based on the change in the peak magnitude of the captured wave signals before and after the indentation, and the damage index was correlated with the residual deformation (defined as the depth of the dent), that was further correlated with the amount of crushing within the core. Both A0 and S0 Lamb wave modes showed high sensitivity to the presence of barely visible indentation damage with residual deformation of 0.2 mm. Furthermore, barely visible indentation damage was assessed in composite sandwich panels after indenting to 3 and 5 mm, and the damage index was defined, based on (a) the peak magnitude of the wave signals before and after indentation or (b) the mismatch between the original and reconstructed wave signals based on a time-reversal algorithm, and was subsequently applied to locate the position of indentation.

Acoustic Streaming and Microparticle Enrichment within a Microliter Droplet Using a Lamb-Wave Resonator Array

NASA Astrophysics Data System (ADS)

Zhang, Hongxiang; Tang, Zifan; Wang, Zhan; Pan, Shuting; Han, Ziyu; Sun, Chongling; Zhang, Menglun; Duan, Xuexin; Pang, Wei

2018-06-01

We report the nonlinear acoustic streaming effect and the fast manipulation of microparticles by microelectromechanical Lamb-wave resonators in a microliter droplet. The device, consisting of four Lamb-wave resonators on a silicon die, generates cylindrical traveling waves in a liquid and efficiently drives nine horizontal vortices within a 1 -μ l droplet; the performance of the device coincides with the numerical model prediction. Experimentally, the particles are enriched at the stagnation center of the main vortex on the free surface of the droplet in open space without microfluidic channels. In addition, the trajectories of the particles in the droplet can be controlled by the excitation power.

Generation mechanism of nonlinear ultrasonic Lamb waves in thin plates with randomly distributed micro-cracks.

PubMed

Zhao, Youxuan; Li, Feilong; Cao, Peng; Liu, Yaolu; Zhang, Jianyu; Fu, Shaoyun; Zhang, Jun; Hu, Ning

2017-08-01

Since the identification of micro-cracks in engineering materials is very valuable in understanding the initial and slight changes in mechanical properties of materials under complex working environments, numerical simulations on the propagation of the low frequency S 0 Lamb wave in thin plates with randomly distributed micro-cracks were performed to study the behavior of nonlinear Lamb waves. The results showed that while the influence of the randomly distributed micro-cracks on the phase velocity of the low frequency S 0 fundamental waves could be neglected, significant ultrasonic nonlinear effects caused by the randomly distributed micro-cracks was discovered, which mainly presented as a second harmonic generation. By using a Monte Carlo simulation method, we found that the acoustic nonlinear parameter increased linearly with the micro-crack density and the size of micro-crack zone, and it was also related to the excitation frequency and friction coefficient of the micro-crack surfaces. In addition, it was found that the nonlinear effect of waves reflected by the micro-cracks was more noticeable than that of the transmitted waves. This study theoretically reveals that the low frequency S 0 mode of Lamb waves can be used as the fundamental waves to quantitatively identify micro-cracks in thin plates. Copyright © 2017 Elsevier B.V. All rights reserved.

Reflection of Lamb waves obliquely incident on the free edge of a plate.

PubMed

Santhanam, Sridhar; Demirli, Ramazan

2013-01-01

The reflection of obliquely incident symmetric and anti-symmetric Lamb wave modes at the edge of a plate is studied. Both in-plane and Shear-Horizontal (SH) reflected wave modes are spawned by an obliquely incident in-plane Lamb wave mode. Energy reflection coefficients are calculated for the reflected wave modes as a function of frequency and angle of incidence. This is done by using the method of orthogonal mode decomposition and by enforcing traction free conditions at the plate edge using the method of collocation. A PZT sensor network, affixed to an Aluminum plate, is used to experimentally verify the predictions of the analysis. Experimental results provide support for the analytically determined results. Copyright © 2012 Elsevier B.V. All rights reserved.

Characterization of Defects in Composite Material Using Rapidly Acquired Leaky Lamb Wave Dispersion Data

NASA Technical Reports Server (NTRS)

Bar-Cohen, Y.; Mal, A.; Chang, Z.

1998-01-01

The phenomenon of Leaky Lamb Wave (LLW) in composite materials was first observed in 1982 using a Schlieren system. It has been studied extensively by numerous investigators and successfully shown to be an effective quantitative NDE tool.

Plane Evanescent Waves and Interface Waves

NASA Astrophysics Data System (ADS)

Luppé, F.; Conoir, J. M.; El Kettani, M. Ech-Cherif; Lenoir, O.; Izbicki, J. L.; Duclos, J.; Poirée, B.

The evanescent plane wave formalism is used to obtain the characteristic equation of the normal vibration modes of a plane elastic solid embedded in a perfect fluid. Simple drawings of the real and imaginary parts of complex wave vectors make quite clear the choice of the Riemann sheets on which the roots of the characteristic equation are to be looked for. The generalized Rayleigh wave and the Scholte - Stoneley wave are then described. The same formalism is used to describe Lamb waves on an elastic plane plate immersed in water. The damping, due to energy leaking in the fluid, is shown to be directly given by the projection of evanescence vectors on the interface. Measured values of the damping coefficient are in good agreement with those derived from calculations. The width of the angular resonances associated to Lamb waves or Rayleigh waves is also directly related to this same evanescence vectors projection, as well as the excitation coefficient of a given Lamb wave excited by a plane incident wave. This study shows clearly the strong correlation between the resonance point of view and the wave one in plane interface problems.

Background Lamb waves in the Earth's atmosphere

NASA Astrophysics Data System (ADS)

Nishida, K.; Kobayashi, N.; Fukao, Y.

2013-12-01

Lamb waves of the Earth's atmosphere in the millihertz band have been considered as transient phenomena excited only by large events [e.g. the major volcanic eruption of Krakatoa in 1833, the impact of Siberian meteorite in 1908, the testing of large nuclear tests and the huge earthquakes, Garrett1969]. In a case of the solid Earth, observation of background free oscillations in the millihertz band-now known as Earth's background free oscillations or seismic hum, has been firmly established. Above 5 mHz, their dominant excitation sources are oceanic infragravity waves. At 3.7 and 4.4 mHz an elasto-acoustic resonance between the solid Earth and the atmosphere was observed [Nishida et al., 2000]. These seismic observations show that the contribution of atmospheric disturbances to the seismic hum is dominant below 5 mHz. Such contribution implies background excitations of acoustic-gravity waves in this frequency range. For direct detection of the background acoustic-gravity waves, our group conducted observations using an array of barometers [Nishida et al. 2005]. However, the spatial scale of the array of about 10 km was too small to detect acoustic modes below 10 mHz. Since then, no direct observations of these waves have been reported. In 2011, 337 high-resolution microbarometers were installed on a continental scale at USArray Transportable Array. The large and dense array enables us to detect the background atmospheric waves. Here, we show the first evidence of background Lamb waves in the Earth's atmosphere from 0.2 to 10 mHz, based on the array analysis of microbarometer data from the USArray in 2012. The observations suggest that the excitation sources are atmospheric disturbances in the troposphere. Theoretically, their energy in the troposphere tunnels into the thermosphere at a resonant frequency via thermospheric gravity wave, where the observed amplitudes indeed take a local minimum. The energy leak through the frequency window could partly contribute to thermospheric wave activity. Tropospheric disturbances exciting background Lamb waves may also be responsible for seismic hum at frequencies below 5 mHz.

Disbond Detection in Bonded Aluminum Joints Using Lamb Wave Amplitude and Time-of-Flight

NASA Technical Reports Server (NTRS)

Sun, Keun J.; Johnston, Patrick H.

1992-01-01

In recent years, there was a need of developing efficient nondestructive integrity assessment techniques for large area laminate structures, such as detections of disbond, crack, and corrosion in fuselage of an aircraft. Together with the improving tomography and computer technologies, progress has been made in many fields in NDE towards a faster inspection. Ultrasonically, Lamb wave is considered to be a candidate for large area inspections based on its capability of propagating a relatively long distance in thin plates and its media-thickness-dependent propagation properties. Moreover, the occurence of disbonds, corrosion, and even cracks often results in reduction of effective thickness of a laminate. The idea is to assess the condition of a structure by sensing the response of propagating Lamb waves to these flaws over long path length. A series of tests in the sequence of disbond, corrosion, and crack have been done on various types of specimen to investigate the feasibility of this approach. This paper will present some of the test results for disbond detection on aluminum lap splice joints.

Damage detection in composite materials using Lamb wave methods

NASA Astrophysics Data System (ADS)

Kessler, Seth S.; Spearing, S. Mark; Soutis, Constantinos

2002-04-01

Cost-effective and reliable damage detection is critical for the utilization of composite materials. This paper presents part of an experimental and analytical survey of candidate methods for in situ damage detection of composite materials. Experimental results are presented for the application of Lamb wave techniques to quasi-isotropic graphite/epoxy test specimens containing representative damage modes, including delamination, transverse ply cracks and through-holes. Linear wave scans were performed on narrow laminated specimens and sandwich beams with various cores by monitoring the transmitted waves with piezoceramic sensors. Optimal actuator and sensor configurations were devised through experimentation, and various types of driving signal were explored. These experiments provided a procedure capable of easily and accurately determining the time of flight of a Lamb wave pulse between an actuator and sensor. Lamb wave techniques provide more information about damage presence and severity than previously tested methods (frequency response techniques), and provide the possibility of determining damage location due to their local response nature. These methods may prove suitable for structural health monitoring applications since they travel long distances and can be applied with conformable piezoelectric actuators and sensors that require little power.

Self-action of propagating and standing Lamb waves in the plates exhibiting hysteretic nonlinearity: Nonlinear zero-group velocity modes.

PubMed

Gusev, Vitalyi E; Lomonosov, Alexey M; Ni, Chenyin; Shen, Zhonghua

2017-09-01

An analytical theory accounting for the influence of hysteretic nonlinearity of micro-inhomogeneous plate material on the Lamb waves near the S 1 zero group velocity point is developed. The theory predicts that the main effect of the hysteretic quadratic nonlinearity consists in the modification of the frequency and the induced absorption of the Lamb modes. The effects of the nonlinear self-action in the propagating and standing Lamb waves are expected to be, respectively, nearly twice and three times stronger than those in the plane propagating acoustic waves. The theory is restricted to the simplest hysteretic nonlinearity, which is influencing only one of the Lamé moduli of the materials. However, possible extensions of the theory to the cases of more general hysteretic nonlinearities are discussed as well as the perspectives of its experimental testing. Applications include nondestructive evaluation of micro-inhomogeneous and cracked plates. Copyright © 2017 Elsevier B.V. All rights reserved.

A Baseline-Free Defect Imaging Technique in Plates Using Time Reversal of Lamb Waves

NASA Astrophysics Data System (ADS)

Hyunjo, Jeong; Sungjong, Cho; Wei, Wei

2011-06-01

We present an analytical investigation for a baseline-free imaging of a defect in plate-like structures using the time-reversal of Lamb waves. We first consider the flexural wave (A0 mode) propagation in a plate containing a defect, and reception and time reversal process of the output signal at the receiver. The received output signal is then composed of two parts: a directly propagated wave and a scattered wave from the defect. The time reversal of these waves recovers the original input signal, and produces two additional sidebands that contain the time-of-flight information on the defect location. One of the side-band signals is then extracted as a pure defect signal. A defect localization image is then constructed from a beamforming technique based on the time-frequency analysis of the side band signal for each transducer pair in a network of sensors. The simulation results show that the proposed scheme enables the accurate, baseline-free imaging of a defect.

Ultrasonic wireless health monitoring

NASA Astrophysics Data System (ADS)

Petit, Lionel; Lefeuvre, Elie; Guyomar, Daniel; Richard, Claude; Guy, Philippe; Yuse, Kaori; Monnier, Thomas

2006-03-01

The integration of autonomous wireless elements in health monitoring network increases the reliability by suppressing power supplies and data transmission wiring. Micro-power piezoelectric generators are an attractive alternative to primary batteries which are limited by a finite amount of energy, a limited capacity retention and a short shelf life (few years). Our goal is to implement such an energy harvesting system for powering a single AWT (Autonomous Wireless Transmitter) using our SSH (Synchronized Switch Harvesting) method. Based on a non linear process of the piezoelement voltage, this SSH method optimizes the energy extraction from the mechanical vibrations. This AWT has two main functions : The generation of an identifier code by RF transmission to the central receiver and the Lamb wave generation for the health monitoring of the host structure. A damage index is derived from the variation between the transmitted wave spectrum and a reference spectrum. The same piezoelements are used for the energy harvesting function and the Lamb wave generation, thus reducing mass and cost. A micro-controller drives the energy balance and synchronizes the functions. Such an autonomous transmitter has been evaluated on a 300x50x2 mm 3 composite cantilever beam. Four 33x11x0.3 mm 3 piezoelements are used for the energy harvesting and for the wave lamb generation. A piezoelectric sensor is placed at the free end of the beam to track the transmitted Lamb wave. In this configuration, the needed energy for the RF emission is 0.1 mJ for a 1 byte-information and the Lamb wave emission requires less than 0.1mJ. The AWT can harvested an energy quantity of approximately 20 mJ (for a 1.5 Mpa lateral stress) with a 470 μF storage capacitor. This corresponds to a power density near to 6mW/cm 3. The experimental AWT energy abilities are presented and the damage detection process is discussed. Finally, some envisaged solutions are introduced for the implementation of the required data processing into an autonomous wireless receiver, in terms of reduction of the energy and memory costs.

Finite element simulation of core inspection in helicopter rotor blades using guided waves.

PubMed

Chakrapani, Sunil Kishore; Barnard, Daniel; Dayal, Vinay

2015-09-01

This paper extends the work presented earlier on inspection of helicopter rotor blades using guided Lamb modes by focusing on inspecting the spar-core bond. In particular, this research focuses on structures which employ high stiffness, high density core materials. Wave propagation in such structures deviate from the generic Lamb wave propagation in sandwich panels. To understand the various mode conversions, finite element models of a generalized helicopter rotor blade were created and subjected to transient analysis using a commercial finite element code; ANSYS. Numerical simulations showed that a Lamb wave excited in the spar section of the blade gets converted into Rayleigh wave which travels across the spar-core section and mode converts back into Lamb wave. Dispersion of Rayleigh waves in multi-layered half-space was also explored. Damage was modeled in the form of a notch in the core section to simulate a cracked core, and delamination was modeled between the spar and core material to simulate spar-core disbond. Mode conversions under these damaged conditions were examined numerically. The numerical models help in assessing the difficulty of using nondestructive evaluation for complex structures and also highlight the physics behind the mode conversions which occur at various discontinuities. Copyright © 2015 Elsevier B.V. All rights reserved.

Lamb wave extraction of dispersion curves in micro/nano-plates using couple stress theories

NASA Astrophysics Data System (ADS)

Ghodrati, Behnam; Yaghootian, Amin; Ghanbar Zadeh, Afshin; Mohammad-Sedighi, Hamid

2018-01-01

In this paper, Lamb wave propagation in a homogeneous and isotropic non-classical micro/nano-plates is investigated. To consider the effect of material microstructure on the wave propagation, three size-dependent models namely indeterminate-, modified- and consistent couple stress theories are used to extract the dispersion equations. In the mentioned theories, a parameter called 'characteristic length' is used to consider the size of material microstructure in the governing equations. To generalize the parametric studies and examine the effect of thickness, propagation wavelength, and characteristic length on the behavior of miniature plate structures, the governing equations are nondimensionalized by defining appropriate dimensionless parameters. Then the dispersion curves for phase and group velocities are plotted in terms of a wide frequency-thickness range to study the lamb waves propagation considering microstructure effects in very high frequencies. According to the illustrated results, it was observed that the couple stress theories in the Cosserat type material predict more rigidity than the classical theory; so that in a plate with constant thickness, by increasing the thickness to characteristic length ratio, the results approach to the classical theory, and by reducing this ratio, wave propagation speed in the plate is significantly increased. In addition, it is demonstrated that for high-frequency Lamb waves, it converges to dispersive Rayleigh wave velocity.

Development of dual PZT transducers for reference-free crack detection in thin plate structures.

PubMed

Sohn, Hoon; Kim, Seuno Bum

2010-01-01

A new Lamb-wave-based nondestructive testing (NDT) technique, which does not rely on previously stored baseline data, is developed for crack monitoring in plate structures. Commonly, the presence of damage is identified by comparing "current data" measured from a potentially damaged stage of a structure with "baseline data" previously obtained at the intact condition of the structure. In practice, structural defects typically take place long after collection of the baseline data, and the baseline data can be also affected by external loading, temperature variations, and changing boundary conditions. To eliminate the dependence on the baseline data comparison, the authors previously developed a reference-free NDT technique using 2 pairs of collocated lead zirconate titanate (PZT) transducers placed on both sides of a plate. This reference-free technique is further advanced in the present study by the necessity of attaching transducers only on a single surface of a structure for certain applications such as aircraft. To achieve this goal, a new design of PZT transducers called dual PZT transducers is proposed. Crack formation creates Lamb wave mode conversion due to a sudden thickness change of the structure. This crack appearance is instantly detected from the measured Lamb wave signals using the dual PZT transducers. This study also suggests a reference-free statistical approach that enables damage classification using only the currently measured data set. Numerical simulations and experiments were conducted using an aluminum plate with uniform thickness and fundamental Lamb waves modes to demonstrate the applicability of the proposed technique to reference-free crack detection.

High-frequency Lamb wave device composed of MEMS structure using LiNbO3 thin film and air gap.

PubMed

Kadota, Michio; Ogami, Takashi; Yamamoto, Kansho; Tochishita, Hikari; Negoro, Yasuhiro

2010-11-01

High-frequency devices operating at 3 GHz or higher are required, for instance, for future 4th generation mobile phone systems in Japan. Using a substrate with a high acoustic velocity is one method to realize a high-frequency acoustic or elastic device. A Lamb wave has a high velocity when the substrate thickness is thin. To realize a high-frequency device operating at 3 GHz or higher using a Lamb wave, a very thin (less than 0.5 μm thick) single-crystal plate must be used. It is difficult to fabricate such a very thin single crystal plate. The authors have attempted to use a c-axis orientated epitaxial LiNbO(3) thin film deposited by a chemical vapor deposition system (CVD) instead of using a thin LiNbO(3) single crystal plate. Lamb wave resonators composed of a interdigital transducer (IDT)/the LiNbO(3) film/air gap/base substrate structure like micro-electromechanical system (MEMS) transducers were fabricated. These resonators have shown a high frequency of 4.5 and 6.3 GHz, which correspond to very high acoustic velocities of 14,000 and 12,500 m/s, respectively, have excellent characteristics such as a ratio of resonant and antiresonant impedance of 52 and 38 dB and a wide band of 7.2% and 3.7%, respectively, and do not have spurious responses caused by the 0th modes of shear horizontal (SH(0)) and symmetric (S(0)) modes.

On the Mathematical Modeling of Single and Multiple Scattering of Ultrasonic Guided Waves by Small Scatterers: A Structural Health Monitoring Measurement Model

NASA Astrophysics Data System (ADS)

Strom, Brandon William

In an effort to assist in the paradigm shift from schedule based maintenance to conditioned based maintenance, we derive measurement models to be used within structural health monitoring algorithms. Our models are physics based, and use scattered Lamb waves to detect and quantify pitting corrosion. After covering the basics of Lamb waves and the reciprocity theorem, we develop a technique for the scattered wave solution. The first application is two-dimensional, and is employed in two different ways. The first approach integrates a traction distribution and replaces it by an equivalent force. The second approach is higher order and uses the actual traction distribution. We find that the equivalent force version of the solution technique holds well for small pits at low frequencies. The second application is three-dimensional. The equivalent force caused by the scattered wave of an arbitrary equivalent force is calculated. We obtain functions for the scattered wave displacements as a function of equivalent forces, equivalent forces as a function of incident wave, and scattered wave amplitudes as a function of incident amplitude. The third application uses self-consistency to derive governing equations for the scattered waves due to multiple corrosion pits. We decouple the implicit set of equations and solve explicitly by using a recursive series solution. Alternatively, we solve via an undetermined coefficient method which results in an interaction operator and solution via matrix inversion. The general solution is given for N pits including mode conversion. We show that the two approaches are equivalent, and give a solution for three pits. Various approximations are advanced to simplify the problem while retaining the leading order physics. As a final application, we use the multiple scattering model to investigate resonance of Lamb waves. We begin with a one-dimensional problem and progress to a three-dimensional problem. A directed graph enables interpretation of the interaction operator, and we show that a series solution converges due to loss of energy in the system. We see that there are four causes of resonance and plot the modulation depth as a function of spacing between the pits.

Effect of pressurization on helical guided wave energy velocity in fluid-filled pipes.

PubMed

Dubuc, Brennan; Ebrahimkhanlou, Arvin; Salamone, Salvatore

2017-03-01

The effect of pressurization stresses on helical guided waves in a thin-walled fluid-filled pipe is studied by modeling leaky Lamb waves in a stressed plate bordered by fluid. Fluid pressurization produces hoop and longitudinal stresses in a thin-walled pipe, which corresponds to biaxial in-plane stress in a plate waveguide model. The effect of stress on guided wave propagation is accounted for through nonlinear elasticity and finite deformation theory. Emphasis is placed on the stress dependence of the energy velocity of the guided wave modes. For this purpose, an expression for the energy velocity of leaky Lamb waves in a stressed plate is derived. Theoretical results are presented for the mode, frequency, and directional dependent variations in energy velocity with respect to stress. An experimental setup is designed for measuring variations in helical wave energy velocity in a thin-walled water-filled steel pipe at different levels of pressure. Good agreement is achieved between the experimental variations in energy velocity for the helical guided waves and the theoretical leaky Lamb wave solutions. Copyright © 2016 Elsevier B.V. All rights reserved.

QEDMOD: Fortran program for calculating the model Lamb-shift operator

NASA Astrophysics Data System (ADS)

Shabaev, V. M.; Tupitsyn, I. I.; Yerokhin, V. A.

2018-02-01

We present Fortran package QEDMOD for computing the model QED operator hQED that can be used to account for the Lamb shift in accurate atomic-structure calculations. The package routines calculate the matrix elements of hQED with the user-specified one-electron wave functions. The operator can be used to calculate Lamb shift in many-electron atomic systems with a typical accuracy of few percent, either by evaluating the matrix element of hQED with the many-electron wave function, or by adding hQED to the Dirac-Coulomb-Breit Hamiltonian.

Lamb wave propagation in monocrystalline silicon wafers.

PubMed

Fromme, Paul; Pizzolato, Marco; Robyr, Jean-Luc; Masserey, Bernard

2018-01-01

Monocrystalline silicon wafers are widely used in the photovoltaic industry for solar panels with high conversion efficiency. Guided ultrasonic waves offer the potential to efficiently detect micro-cracks in the thin wafers. Previous studies of ultrasonic wave propagation in silicon focused on effects of material anisotropy on bulk ultrasonic waves, but the dependence of the wave propagation characteristics on the material anisotropy is not well understood for Lamb waves. The phase slowness and beam skewing of the two fundamental Lamb wave modes A 0 and S 0 were investigated. Experimental measurements using contact wedge transducer excitation and laser measurement were conducted. Good agreement was found between the theoretically calculated angular dependency of the phase slowness and measurements for different propagation directions relative to the crystal orientation. Significant wave skew and beam widening was observed experimentally due to the anisotropy, especially for the S 0 mode. Explicit finite element simulations were conducted to visualize and quantify the guided wave beam skew. Good agreement was found for the A 0 mode, but a systematic discrepancy was observed for the S 0 mode. These effects need to be considered for the non-destructive testing of wafers using guided waves.

Imaging of a Defect in Thin Plates Using the Time Reversal of Single Mode Lamb Waves

NASA Astrophysics Data System (ADS)

Jeong, Hyunjo; Lee, Jung-Sik; Bae, Sung-Min

2011-06-01

This paper presents an analytical investigation for a baseline-free imaging of a defect in plate-like structures using the time-reversal of Lamb waves. We first consider the flexural wave (A0 mode) propagation in a plate containing a defect, and reception and time reversal process of the output signal at the receiver. The received output signal is then composed of two parts: a directly propagated wave and a scattered wave from the defect. The time reversal of these waves recovers the original input signal, and produces two additional sidebands that contain the time-of-flight information on the defect location. One of the side band signals is then extracted as a pure defect signal. A defect localization image is then constructed from a beamforming technique based on the time-frequency analysis of the side band signal for each transducer pair in a network of sensors. The simulation results show that the proposed scheme enables the accurate, baseline-free detection of a defect, so that experimental studies are needed to verify the proposed method and to be applied to real structure.

ANALYTICAL SOLUTION FOR WAVES IN PLANETS WITH ATMOSPHERIC SUPERROTATION. II. LAMB, SURFACE, AND CENTRIFUGAL WAVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peralta, J.; López-Valverde, M. A.; Imamura, T.

2014-07-01

This paper is the second in a two-part study devoted to developing tools for a systematic classification of the wide variety of atmospheric waves expected on slowly rotating planets with atmospheric superrotation. Starting with the primitive equations for a cyclostrophic regime, we have deduced the analytical solution for the possible waves, simultaneously including the effect of the metric terms for the centrifugal force and the meridional shear of the background wind. In those cases where the conditions for the method of the multiple scales in height are met, these wave solutions are also valid when vertical shear of the backgroundmore » wind is present. A total of six types of waves have been found and their properties were characterized in terms of the corresponding dispersion relations and wave structures. In this second part, we study the waves' solutions when several atmospheric approximations are applied: Lamb, surface, and centrifugal waves. Lamb and surface waves are found to be quite similar to those in a geostrophic regime. By contrast, centrifugal waves turn out to be a special case of Rossby waves that arise in atmospheres in cyclostrophic balance. Finally, we use our results to identify the nature of the waves behind atmospheric periodicities found in polar and lower latitudes of Venus's atmosphere.« less

Bilinear Time-frequency Analysis for Lamb Wave Signal Detected by Electromagnetic Acoustic Transducer

NASA Astrophysics Data System (ADS)

Sun, Wenxiu; Liu, Guoqiang; Xia, Hui; Xia, Zhengwu

2018-03-01

Accurate acquisition of the detection signal travel time plays a very important role in cross-hole tomography. The experimental platform of aluminum plate under the perpendicular magnetic field is established and the bilinear time-frequency analysis methods, Wigner-Ville Distribution (WVD) and the pseudo-Wigner-Ville distribution (PWVD), are applied to analyse the Lamb wave signals detected by electromagnetic acoustic transducer (EMAT). By extracting the same frequency component of the time-frequency spectrum as the excitation frequency, the travel time information can be obtained. In comparison with traditional linear time-frequency analysis method such as short-time Fourier transform (STFT), the bilinear time-frequency analysis method PWVD is more appropriate in extracting travel time and recognizing patterns of Lamb wave.

Lamb Wave Response of Fatigued Composite Samples

NASA Technical Reports Server (NTRS)

Seale, Michael; Smith, Barry T.; Prosser, William H.; Masters, John E.

1994-01-01

Composite materials are being more widely used today by aerospace, automotive, sports equipment, and a number of other commercial industries because of their advantages over conventional metals. Composites have a high strength-to-weight ratio and can be constructed to meet specific design needs. Composite structures are already in use in secondary parts of the Douglas MD-11 and are planned to be used in the new MD-12X. Plans also exist for their use in primary and secondary structures on the Boeing 777. Douglas proposed MD-XX may also incorporate composite materials into primary structures such as the wings and tail. Use of composites in these structures offers weight savings, corrosion resistance, and improved aerodynamics. Additionally, composites have been used to repair cracks in many B-1Bs where traditional repair techniques were not very effective. Plans have also been made to reinforce all of the remaining B-1s with composite materials. Verification of the structural integrity of composite components is needed to insure safe operation of these aerospace vehicles. One aspect of the use of these composites is their response to fatigue. To track this progression of fatigue in aerospace structures, a convenient method to nondestructively monitor this damage needs to be developed. Traditional NDE techniques used on metals are not easily adaptable to composites due to the inhomogeneous and anisotropic nature of these materials. Finding an effective means of nondestructively monitoring fatigue damage is extremely important to the safety and reliability of such structures. Lamb waves offer one method of evaluating these composite materials. As a material is fatigued, the modulus degrades. Since the Lamb wave velocity can be related to the modulus of the material, an effective tool can be developed to monitor fatigue damage in composites by measuring the velocity of these waves. In this work, preliminary studies have been conducted which monitor fatigue damage in composite samples using strain gage measurements as well as Lamb wave velocity measurements. A description of the test samples is followed by the results of two different measurements of Lamb wave velocity. The first technique is a contact measurement done at a single frequency, while the second involves an immersion study of Lamb waves in which dispersion curves are obtained. The results of the Lamb wave monitoring of fatigue damage is compared to the damage progression measured by strain gages. The final section discusses the results and conclusions.

Crack Detection with Lamb Wave Wavenumber Analysis

NASA Technical Reports Server (NTRS)

Tian, Zhenhua; Leckey, Cara; Rogge, Matt; Yu, Lingyu

2013-01-01

In this work, we present our study of Lamb wave crack detection using wavenumber analysis. The aim is to demonstrate the application of wavenumber analysis to 3D Lamb wave data to enable damage detection. The 3D wavefields (including vx, vy and vz components) in time-space domain contain a wealth of information regarding the propagating waves in a damaged plate. For crack detection, three wavenumber analysis techniques are used: (i) two dimensional Fourier transform (2D-FT) which can transform the time-space wavefield into frequency-wavenumber representation while losing the spatial information; (ii) short space 2D-FT which can obtain the frequency-wavenumber spectra at various spatial locations, resulting in a space-frequency-wavenumber representation; (iii) local wavenumber analysis which can provide the distribution of the effective wavenumbers at different locations. All of these concepts are demonstrated through a numerical simulation example of an aluminum plate with a crack. The 3D elastodynamic finite integration technique (EFIT) was used to obtain the 3D wavefields, of which the vz (out-of-plane) wave component is compared with the experimental measurement obtained from a scanning laser Doppler vibrometer (SLDV) for verification purposes. The experimental and simulated results are found to be in close agreement. The application of wavenumber analysis on 3D EFIT simulation data shows the effectiveness of the analysis for crack detection. Keywords: : Lamb wave, crack detection, wavenumber analysis, EFIT modeling

Lamb waves in plates covered by a two-dimensional phononic film

NASA Astrophysics Data System (ADS)

Bonello, Bernard; Charles, Christine; Ganot, François

2007-01-01

The propagation of Lamb waves in silicon plates coated by a very thin two-dimensional phononic film is studied experimentally. The dispersion curves are measured using a laser ultrasonics technique. The data are then compared to the calculated dispersion curves of the uncoated silicon plate. The overall shapes of the lower-order symmetric and antisymmetric Lamb modes are not altered by the thin phononic film, except by the appearing of frequency band gaps at the edges of both the first and the second Brillouin zone. The influence of the filling fraction on the magnitude of the gaps is investigated experimentally.

Experimental investigation of leaky lamb modes by an optically induced grating.

PubMed

Van de Rostyne, Kris; Glorieux, Christ; Gao, Weimin; Lauriks, Walter; Thoen, Jan

2002-09-01

By removing the symmetry of a free plate configuration, fluid loading significantly modifies the nature of acoustic waves travelling along a plate, and it even gives existence to new acoustic modes. We present theoretical predictions for the existence, dispersive behavior, and spatial distribution of leaky Lamb waves in a fluid-loaded film. Although Lamb modes are often investigated by studying the radiated fluid waves resulting from their leakage, here their properties are assessed by detecting the wave displacements directly using laser beam deflection. By using crossed laser beam excitation, the detection and analysis of the different modes is done at a fixed wavelength, allowing one to verify the existence, the velocity, and the damping of each predicted mode in a simple and unambiguous way. Our theoretical predictions for the nature of the modes in a water-loaded Plexiglas film, including parts of looping modes, are experimentally confirmed.

Smart Sound Processing for Defect Sizing in Pipelines Using EMAT Actuator Based Multi-Frequency Lamb Waves

PubMed Central

García-Gómez, Joaquín; Rosa-Zurera, Manuel; Romero-Camacho, Antonio; Jiménez-Garrido, Jesús Antonio; García-Benavides, Víctor

2018-01-01

Pipeline inspection is a topic of particular interest to the companies. Especially important is the defect sizing, which allows them to avoid subsequent costly repairs in their equipment. A solution for this issue is using ultrasonic waves sensed through Electro-Magnetic Acoustic Transducer (EMAT) actuators. The main advantage of this technology is the absence of the need to have direct contact with the surface of the material under investigation, which must be a conductive one. Specifically interesting is the meander-line-coil based Lamb wave generation, since the directivity of the waves allows a study based in the circumferential wrap-around received signal. However, the variety of defect sizes changes the behavior of the signal when it passes through the pipeline. Because of that, it is necessary to apply advanced techniques based on Smart Sound Processing (SSP). These methods involve extracting useful information from the signals sensed with EMAT at different frequencies to obtain nonlinear estimations of the depth of the defect, and to select the features that better estimate the profile of the pipeline. The proposed technique has been tested using both simulated and real signals in steel pipelines, obtaining good results in terms of Root Mean Square Error (RMSE). PMID:29518927

Experimental and theoretical study of Rayleigh-Lamb wave propagation

NASA Technical Reports Server (NTRS)

Rogers, Wayne P.; Datta, Subhendu K.; Ju, T. H.

1990-01-01

Many space structures, such as the Space Station Freedom, contain critical thin-walled components. The structural integrity of thin-walled plates and shells can be monitored effectively using acoustic emission and ultrasonic testing in the Rayleigh-Lamb wave frequency range. A new PVDF piezoelectric sensor has been developed that is well suited to remote, inservice nondestructive evaluation of space structures. In the present study the new sensor was used to investigate Rayleigh-Lamb wave propagation in a plate. The experimental apparatus consisted of a glass plate (2.3 m x 25.4 mm x 5.6 mm) with PVDF sensor (3 mm diam.) mounted at various positions along its length. A steel ball impact served as a simulated acoustic emission source, producing surface waves, shear waves and longitudinal waves with dominant frequencies between 1 kHz and 200 kHz. The experimental time domain wave-forms were compared with theoretical predictions of the wave propagation in the plate. The model uses an analytical solution for the Green's function and the measured response at a single position to predict response at any other position in the plate. Close agreement was found between the experimental and theoretical results.

Modeling of phase velocity and frequency spectrum of guided Lamb waves in piezoelectric-semiconductor multilayered structures made of AlAs and GaAs

NASA Astrophysics Data System (ADS)

Othmani, Cherif; Takali, Farid; Njeh, Anouar

2017-11-01

Modeling of guided Lamb waves propagation in piezoelectric-semiconductor multilayered structures made of AlAs and GaAs is evaluated in this paper. Here, the Legendre polynomial method is used to calculate dispersion curves, frequency spectrum and field distributions of guided Lamb waves propagation modes in AlAs, GaAs, AlAs/GaAs and AlAs/GaAs/AlAs-1/2/1 structures. In fact, formulations are given for open-circuit surface. Consequently, the polynomial method is numerically stable according to the total number of layers and the frequency range. This analysis is meaningful for the applications of the piezoelectric-semiconductor multilayered structures made of AlAs and GaAs such as in novel acoustic devices.

Impact damage detection in sandwich composite structures using Lamb waves and laser vibrometry

NASA Astrophysics Data System (ADS)

Lamboul, B.; Passilly, B.; Roche, J.-M.; Osmont, D.

2013-01-01

This experimental study explores the feasibility of impact damage detection in composite sandwich structures using Lamb wave excitation and signals acquired with a laser Doppler vibrometer. Energy maps are computed from the transient velocity wave fields and used to highlight defect areas in impacted coupons of foam core and honeycomb core sandwich materials. The technique performs well for the detection of barely visible damage in this type of material, and is shown to be robust in the presence of wave reverberation. Defect extent information is not always readily retrieved from the obtained defect signatures, which depend on the wave - defect interaction mechanisms.

Focusing guided waves using surface bonded elastic metamaterials

NASA Astrophysics Data System (ADS)

Yan, Xiang; Zhu, Rui; Huang, Guoliang; Yuan, Fuh-Gwo

2013-09-01

Bonding a two-dimensional planar array of small lead discs on an aluminum plate with silicone rubber is shown numerically to focus low-frequency flexural guided waves. The "effective mass density profile" of this type of elastic metamaterials (EMMs), perpendicular to wave propagation direction, is carefully tailored and designed, which allows rays of flexural A0 mode Lamb waves to bend in succession and then focus through a 7 × 9 planar array. Numerical simulations show that Lamb waves can be focused beyond EMMs region with amplified displacement and yet largely retained narrow banded waveform, which may have potential application in structural health monitoring.

Mixing of ultrasonic Lamb waves in thin plates with quadratic nonlinearity.

PubMed

Li, Feilong; Zhao, Youxuan; Cao, Peng; Hu, Ning

2018-07-01

This paper investigates the propagation of Lamb waves in thin plates with quadratic nonlinearity by one-way mixing method using numerical simulations. It is shown that an A 0 -mode wave can be generated by a pair of S 0 and A 0 mode waves only when mixing condition is satisfied, and mixing wave signals are capable of locating the damage zone. Additionally, it is manifested that the acoustic nonlinear parameter increases linearly with quadratic nonlinearity but monotonously with the size of mixing zone. Furthermore, because of frequency deviation, the waveform of the mixing wave changes significantly from a regular diamond shape to toneburst trains. Copyright © 2018 Elsevier B.V. All rights reserved.

Legendre polynomial modeling for vibrations of guided Lamb waves modes in [001]c, [011]c and [111]c polarized (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (x = 0.29 and 0.33) piezoelectric plates: Physical phenomenon of multiple intertwining of An and Sn modes

NASA Astrophysics Data System (ADS)

Othmani, Cherif; Takali, Farid; Njeh, Anouar

2017-12-01

Guided wave devices have recently become one of the most important applications in the industry because such waves are directly related to applications in sensor technology, chemical sensing, agricultural science, fields of bio-sensing and surface acoustic wave (SAW) devices that are used in electronic filters and signal processing. On that account, this numerical investigation aims to study the propagation behavior of guided Lamb waves in a (1-x)Pb(Mg1/3Nb2/3)O3- x PbTiO3 [PMN- x PT] ( x=0.29 or 0.33) piezoelectric single crystal plate. In fact, the PMN- xPT ( x=0.29 or 0.33) piezoelectric crystals are being polarized along [001]c, [011]c and [111]c of the cubic reference directions so that the macroscopic symmetries are tetragonal 4 mm, orthogonal mm2 and rhombohedral 3 m, respectively. Both open- and short-circuit conditions are considered. Here, the Legendre polynomial method is proposed to solve the guided Lamb waves equations. The validity of the proposed method is illustrated by comparison with the ordinary differential equation (ODE). The convergence of this method is discussed. Consequently, the converged results are obtained with very low truncation order M . This constitutes a major advantage of the present method when compared with the other matrix methods. There is cross-crossings among multiple modes for both symmetric ( Sn) and the anti-symmetric ( An) guided Lamb waves propagation. A displacement field has been illustrated to judge whether Sn and An modes cross with each other. Moreover, electric displacement, stress field and electric potential for the open-circuit case were presented for both S0 and A0 Lamb modes.

Guided ultrasonic wave beam skew in silicon wafers

NASA Astrophysics Data System (ADS)

Pizzolato, Marco; Masserey, Bernard; Robyr, Jean-Luc; Fromme, Paul

2018-04-01

In the photovoltaic industry, monocrystalline silicon wafers are employed for solar cells with high conversion efficiency. Micro-cracks induced by the cutting process in the thin wafers can lead to brittle wafer fracture. Guided ultrasonic waves would offer an efficient methodology for the in-process non-destructive testing of wafers to assess micro-crack density. The material anisotropy of the monocrystalline silicon leads to variations of the guided wave characteristics, depending on the propagation direction relative to the crystal orientation. Selective guided ultrasonic wave excitation was achieved using a contact piezoelectric transducer with custom-made wedges for the A0 and S0 Lamb wave modes and a transducer holder to achieve controlled contact pressure and orientation. The out-of-plane component of the guided wave propagation was measured using a non-contact laser interferometer. The phase slowness (velocity) of the two fundamental Lamb wave modes was measured experimentally for varying propagation directions relative to the crystal orientation and found to match theoretical predictions. Significant wave beam skew was observed experimentally, especially for the S0 mode, and investigated from 3D finite element simulations. Good agreement was found with the theoretical predictions based on nominal material properties of the silicon wafer. The important contribution of guided wave beam skewing effects for the non-destructive testing of silicon wafers was demonstrated.

Low-cost ultrasonic lamb-wave transducer

NASA Technical Reports Server (NTRS)

Kammerer, C. C.

1978-01-01

Transducer propagates Lamb wave through thin aluminum sheet material. Model includes two elements that measure effects of damping and loading which, in turn, are indirectly equated to bond integrity. Transducer has been used to evaluate bond integrity of aluminum facing adhesively bonded to aluminum facing. Because of versatility, it is now possible to inspect many objects of different configurations that could not be reached with earlier transducers.

Lamb wave based damage detection using Matching Pursuit and Support Vector Machine classifier

NASA Astrophysics Data System (ADS)

Agarwal, Sushant; Mitra, Mira

2014-03-01

In this paper, the suitability of using Matching Pursuit (MP) and Support Vector Machine (SVM) for damage detection using Lamb wave response of thin aluminium plate is explored. Lamb wave response of thin aluminium plate with or without damage is simulated using finite element. Simulations are carried out at different frequencies for various kinds of damage. The procedure is divided into two parts - signal processing and machine learning. Firstly, MP is used for denoising and to maintain the sparsity of the dataset. In this study, MP is extended by using a combination of time-frequency functions as the dictionary and is deployed in two stages. Selection of a particular type of atoms lead to extraction of important features while maintaining the sparsity of the waveform. The resultant waveform is then passed as input data for SVM classifier. SVM is used to detect the location of the potential damage from the reduced data. The study demonstrates that SVM is a robust classifier in presence of noise and more efficient as compared to Artificial Neural Network (ANN). Out-of-sample data is used for the validation of the trained and tested classifier. Trained classifiers are found successful in detection of the damage with more than 95% detection rate.

Baseline-Subtraction-Free (BSF) Damage-Scattered Wave Extraction for Stiffened Isotropic Plates

NASA Technical Reports Server (NTRS)

He, Jiaze; Leser, Patrick E.; Leser, William P.

2017-01-01

Lamb waves enable long distance inspection of structures for health monitoring purposes. However, this capability is diminished when applied to complex structures where damage-scattered waves are often buried by scattering from various structural components or boundaries in the time-space domain. Here, a baseline-subtraction-free (BSF) inspection concept based on the Radon transform (RT) is proposed to identify and separate these scattered waves from those scattered by damage. The received time-space domain signals can be converted into the Radon domain, in which the scattered signals from structural components are suppressed into relatively small regions such that damage-scattered signals can be identified and extracted. In this study, a piezoelectric wafer and a linear scan via laser Doppler vibrometer (LDV) were used to excite and acquire the Lamb-wave signals in an aluminum plate with multiple stiffeners. Linear and inverse linear Radon transform algorithms were applied to the direct measurements. The results demonstrate the effectiveness of the Radon transform as a reliable extraction tool for damage-scattered waves in a stiffened aluminum plate and also suggest the possibility of generalizing this technique for application to a wide variety of complex, large-area structures.

Extremely low-frequency Lamb wave band gaps in a sandwich phononic crystal thin plate

NASA Astrophysics Data System (ADS)

Shen, Li; Wu, Jiu Hui; Liu, Zhangyi; Fu, Gang

2015-11-01

In this paper, a kind of sandwich phononic crystal (PC) plate with silicon rubber scatterers embedded in polymethyl methacrylate (PMMA) matrix is proposed to demonstrate its low-frequency Lamb wave band gap (BG) characteristics. The dispersion relationship and the displacement vector fields of the basic slab modes and the locally resonant modes are investigated to show the BG formation mechanism. The anti-symmetric Lamb wave BG is further studied due to its important function in reducing vibration. The analysis on the BG characteristics of the PC through changing their geometrical parameters is performed. By optimizing the structure, a sandwich PC plate with a thickness of only 3 mm and a lower boundary (as low as 23.9 Hz) of the first anti-symmetric BG is designed. Finally, sound insulation experiment on a sandwich PC plate with the thickness of only 2.5 mm is conducted, showing satisfactory noise reduction effect in the frequency range of the anti-symmetric Lamb BG. Therefore, this kind of sandwich PC plate has potential applications in controlling vibration and noise in low-frequency ranges.

ULTRASONIC FLAW DETECTION METHOD AND MEANS

DOEpatents

Worlton, D.C.

1961-08-15

A method of detecting subsurface flaws in an object using ultrasonic waves is described. An ultnasonic wave of predetermined velocity and frequency is transmitted to engage the surface of the object at a predetermined angle of inci dence thereto. The incident angle of the wave to the surface is determined with respect to phase velocity, incident wave velocity, incident wave frequency, and the estimated depth of the flaw so that Lamb waves of a particular type and mode are induced only in the portion of the object between the flaw and the surface. These Lamb waves are then detected as they leave the object at an angle of exit equal to the angle of incidence. No waves wlll be generated in the object and hence received if no flaw exists beneath the surface. (AEC)

Neural-Fuzzy model Based Steel Pipeline Multiple Cracks Classification

NASA Astrophysics Data System (ADS)

Elwalwal, Hatem Mostafa; Mahzan, Shahruddin Bin Hj.; Abdalla, Ahmed N.

2017-10-01

While pipes are cheaper than other means of transportation, this cost saving comes with a major price: pipes are subject to cracks, corrosion etc., which in turn can cause leakage and environmental damage. In this paper, Neural-Fuzzy model for multiple cracks classification based on Lamb Guide Wave. Simulation results for 42 sample were collected using ANSYS software. The current research object to carry on the numerical simulation and experimental study, aiming at finding an effective way to detection and the localization of cracks and holes defects in the main body of pipeline. Considering the damage form of multiple cracks and holes which may exist in pipeline, to determine the respective position in the steel pipe. In addition, the technique used in this research a guided lamb wave based structural health monitoring method whereas piezoelectric transducers will use as exciting and receiving sensors by Pitch-Catch method. Implementation of simple learning mechanism has been developed specially for the ANN for fuzzy the system represented.

Lamb Waves Decomposition and Mode Identification Using Matching Pursuit Method

DTIC Science & Technology

2009-01-01

Wigner - Ville distribution ( WVD ). However, WVD suffers from severe interferences, called cross-terms. Cross- terms are the area of a time-frequency...transform (STFT), wavelet transform, Wigner - Ville distribution , matching pursuit decomposition, etc. 1 Report Documentation Page Form ApprovedOMB No...MP decomposition using chirplet dictionary was applied to a simulated S0 mode Lamb wave shown previously in Figure 2a. Wigner - Ville distribution of

Tunable modulation of refracted lamb wave front facilitated by adaptive elastic metasurfaces

NASA Astrophysics Data System (ADS)

Li, Shilong; Xu, Jiawen; Tang, J.

2018-01-01

This letter reports designs of adaptive metasurfaces capable of modulating incoming wave fronts of elastic waves through electromechanical-tuning of their cells. The proposed elastic metasurfaces are composed of arrayed piezoelectric units with individually connected negative capacitance elements that are online tunable. By adjusting the negative capacitances properly, accurately formed, discontinuous phase profiles along the elastic metasurfaces can be achieved. Subsequently, anomalous refraction with various angles can be realized on the transmitted lowest asymmetric mode Lamb wave. Moreover, designs to facilitate planar focal lenses and source illusion devices can also be accomplished. The proposed flexible and versatile strategy to manipulate elastic waves has potential applications ranging from structural fault detection to vibration/noise control.

Scattering of Lamb waves by cracks in a composite graphite fiber-reinforced epoxy plate

NASA Technical Reports Server (NTRS)

Bratton, Robert; Datta, Subhendu K.; Shah, Arvind

1990-01-01

Recent investigations of space construction techniques have explored the used of composite materials in the construction of space stations and platforms. These composites offer superior strength to weight ratio and are thermally stable. For example, a composite material being considered is laminates of graphite fibers in an epoxy matrix. The overall effective elastic constants of such a medium can be calculated from fiber and matrix properties by using an effective modulus theory as shown in Datta, el. al. The investigation of propagation and scattering of elastic waves in composite materials is necessary in order to develop an ability to characterize cracks and predict the reliability of composite structures. The objective of this investigation is the characterization of a surface breaking crack by ultrasonic techniques. In particular, the use of Lamb waves for this purpose is studied here. The Lamb waves travel through the plate, encountering a crack, and scatter. Of interest is the modeling of the scattered wave in terms of the Lamb wave modes. The direct problem of propagation and scattering of Lamb waves by a surface breaking crack has been analyzed. This would permit an experimentalist to characterize the crack by comparing the measured response to the analytical model. The plate is assumed to be infinite in the x and y directions with a constant thickness in the z direction. The top and bottom surfaces are traction free. Solving the governing wave equations and using the stress-free boundary conditions results in the dispersion equation. This equation yields the guided modes in the homogeneous plate. The theoretical model is a hybrid method that combines analytical and finite elements techniques to describe the scattered displacements. A finite region containing the defects is discretized by finite elements. Outside the local region, the far field solution is expressed as a Fourier summation of the guided modes obtained from the dispersion equation. Continuity of tractions and displacements at the boundaries of the two regions provides the necessary equations to determine the expansion coefficients and the nodal displacements. In the hybrid method used here these defects can be of arbitrary shapes as well as inclusions of different materials.

Influence of stacking sequence on scattering characteristics of the fundamental anti-symmetric Lamb wave at through holes in composite laminates.

PubMed

Veidt, Martin; Ng, Ching-Tai

2011-03-01

This paper investigates the scattering characteristics of the fundamental anti-symmetric (A(0)) Lamb wave at through holes in composite laminates. Three-dimensional (3D) finite element (FE) simulations and experimental measurements are used to study the physical phenomenon. Unidirectional, bidirectional, and quasi-isotropic composite laminates are considered in the study. The influence of different hole diameter to wavelength aspect ratios and different stacking sequences on wave scattering characteristics are investigated. The results show that amplitudes and directivity distribution of the scattered Lamb wave depend on these parameters. In the case of quasi-isotropic composite laminates, the scattering directivity patterns are dominated by the fiber orientation of the outer layers and are quite different for composite laminates with the same number of laminae but different stacking sequence. The study provides improved physical insight into the scattering phenomena at through holes in composite laminates, which is essential to develop, validate, and optimize guided wave damage detection and characterization techniques. © 2011 Acoustical Society of America

Temperature Compensation of Aluminum Nitride Lamb Wave Resonators Utilizing the Lowest-Order Symmetric Mode

DTIC Science & Technology

2012-12-14

PZT ceramic plate [40]. Since then Lamb wave devices utilizing the lowest-order antisymmetric (A0) mode propagation in ZnO thin plate were widely...Million Pt Platinum PVDF Polyvinylidene Flouride PZT Lead Zirconium Titanate Q Quality Factor R Resistor RIE Reactive Ion Etching Rm Motional...GaAs), silicon carbide (SiC), langasite (LGS), lead zirconium titanate ( PZT ), and polyvinylidene flouride (PVDF). Each piezoelectric material has

Acoustoelastic Lamb Wave Propagation in Biaxially Stressed Plates (Preprint)

DTIC Science & Technology

2012-03-01

0188 The public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing...control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS. 1 . REPORT DATE (DD-MM-YY) 2. REPORT TYPE 3. DATES COVERED (From - To) March 2012...Journal Article 1 March 2012 – 1 March 2012 4. TITLE AND SUBTITLE ACOUSTOELASTIC LAMB WAVE PROPAGATION IN BIAXIALLY STRESSED PLATES (PREPRINT

Spiral-shaped piezoelectric sensors for Lamb waves direction of arrival (DoA) estimation

NASA Astrophysics Data System (ADS)

De Marchi, L.; Testoni, N.; Marzani, A.

2018-04-01

A novel strategy to design piezoelectric sensors suited for direction of arrival (DoA) estimation of incoming Lamb waves is presented in this work. The designed sensor is composed by two piezoelectric patches (P1, P2) bonded on the structure to be inspected. In particular, by exploiting the Radon transform, the proposed procedure computes the shape of P2 given the shape of P1 so that the difference in time of arrival (DToA) of the Lamb waves at the two patches is linearly related to the DoA while being agnostic of the waveguide dispersion curves. With a dedicated processing procedure, the waveforms acquired from the two electrodes and digitized can be used to retrieve the DoA information. Numerical and experimental results show that DoA estimation performed by means of the proposed shaped transducers is extremely robust.

Modeling a surface-mounted Lamb wave emission-reception system: applications to structural health monitoring.

PubMed

Moulin, Emmanuel; Grondel, Sébastien; Assaad, Jamal; Duquenne, Laurent

2008-12-01

The work described in this paper is intended to present a simple and efficient way of modeling a full Lamb wave emission and reception system. The emitter behavior and the Lamb wave generation are predicted using a two-dimensional (2D) hybrid finite element-normal mode expansion model. Then the receiver electrical response is obtained from a finite element computation with prescribed displacements. A numerical correction is applied to the 2D results in order to account for the in-plane radiation divergence caused by the finite length of the emitter. The advantage of this modular approach is that realistic configurations can be simulated without performing cumbersome modeling and time-consuming computations. It also provides insight into the physical interpretation of the results. A good agreement is obtained between predicted and measured signals. The range of application of the method is discussed.

Characterization of Degradation Progressive in Composite Laminates Subjected to Thermal Fatigue and Moisture Diffusion by Lamb Waves.

PubMed

Li, Weibin; Xu, Chunguang; Cho, Younho

2016-02-19

Laminate composites which are widely used in the aeronautical industry, are usually subjected to frequency variation of environmental temperature and excessive humidity in the in-service environment. The thermal fatigue and moisture absorption in composites may induce material degradation. There is a demand to investigate the coupling damages mechanism and characterize the degradation evolution of composite laminates for the particular application. In this paper, the degradation evolution in unidirectional carbon/epoxy composite laminates subjected to thermal fatigue and moisture absorption is characterized by Lamb waves. The decrease rate of Lamb wave velocity is used to track the degradation evolution in the specimens. The results show that there are two stages for the progressive degradation of composites under the coupling effect of thermal cyclic loading and moisture diffusion. The present work provides an alternative to monitoring the degradation evolution of in-service aircraft composite Laminates.

Second order harmonic guided wave mutual interactions in plate: Vector analysis, numerical simulation, and experimental results

NASA Astrophysics Data System (ADS)

Hasanian, Mostafa; Lissenden, Cliff J.

2017-08-01

The extraordinary sensitivity of nonlinear ultrasonic waves to the early stages of material degradation makes them excellent candidates for nondestructive material characterization. However, distinguishing weak material nonlinearity from instrumentation nonlinearity remains problematic for second harmonic generation approaches. A solution to this problem is to mix waves having different frequencies and to let their mutual interaction generate sum and difference harmonics at frequencies far from those of the instrumentation. Mixing of bulk waves and surface waves has been researched for some time, but mixing of guided waves has not yet been investigated in depth. A unique aspect of guided waves is their dispersive nature, which means we need to assure that a wave can propagate at the sum or difference frequency. A wave vector analysis is conducted that enables selection of primary waves traveling in any direction that generate phase matched secondary waves. We have tabulated many sets of primary waves and phase matched sum and difference harmonics. An example wave mode triplet of two counter-propagating collinear shear horizontal waves that interact to generate a symmetric Lamb wave at the sum frequency is simulated using finite element analysis and then laboratory experiments are conducted. The finite element simulation eliminates issues associated with instrumentation nonlinearities and signal-to-noise ratio. A straightforward subtraction method is used in the experiments to identify the material nonlinearity induced mutual interaction and show that the generated Lamb wave propagates on its own and is large enough to measure. Since the Lamb wave has different polarity than the shear horizontal waves the material nonlinearity is clearly identifiable. Thus, the mutual interactions of shear horizontal waves in plates could enable volumetric characterization of material in remote regions from transducers mounted on just one side of the plate.

Laser-based ultrasonics by dual-probe interferometer detection and narrow-band ultrasound generation

NASA Astrophysics Data System (ADS)

Huang, Jin

1993-01-01

Despite the advantages of laser-based ultrasonic (LBU) systems, the overall sensitivity of LBU systems needs to be improved for practical applications. Progress is reported to achieve better LBU detection accuracy and sensitivity for applications with surface waves and Lamb waves. A novel dual-probe laser interferometer has been developed to measure the same signal at two points. The dual-probe interferometer is a modification of a conventional single-probe interferometer in that the reference beam is guided to a second detecting point on the specimen surface to form a differential measurement mode, which measure the difference of the displacements at the two points. This dual-probe interferometer is particularly useful for accurate measurements of the speed and attenuation of surface waves and Lamb waves. The dual-probe interferometer has been applied to obtain accurate measurements of the surface wave speed and attenuation on surfaces of increasing surface roughness. It has also been demonstrated that with an appropriate signal processing method, namely, the power cepstrum method, the dual-probe interferometer is applicable to measure the local surface wave speed even when the probe separation is so small that the two waveforms in the interferometer output signal overlap in the time domain. Narrow-band signal generation and detection improve the sensitivity of LBU systems. It is proposed to use a diffraction grating to form an array of illuminating strips which form a source of narrowband surface and Lamb waves. The line-array of thermoelastic sources generates narrow-band signals whose frequency and bandwidth can be easily controlled. The optimum line-array parameters, such as width, spacing and the number of lines in the array have been derived theoretically and verified experimentally. Narrow-band signal generation with optimum parameters has been demonstrated. The enhanced LBU system with dual-probe detection and narrowband signal generation has been successfully applied to the detection of cracks emanating from rivet holes in aircraft fuselage panel samples. A compact fiber-optic dual-probe interferometer has also been developed and applied to the above mentioned problem of crack detection. Results agree well with those obtained with a bulk LBU system.

Strain Wave Acquisition by a Fiber Optic Coherent Sensor for Impact Monitoring

PubMed Central

Sbarufatti, Claudio; Beligni, Alessio; Gilioli, Andrea; Ferrario, Maddalena; Mattarei, Marco; Martinelli, Mario; Giglio, Marco

2017-01-01

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, for both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The sensing fiber can be arranged into different layouts, depending on the requirement of the specific application, in order to enhance the sensor sensitivity while still ensuring a limited gauge length if punctual measures are required. For active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal only in correspondence to the sensing points of interest. Instead, for passive impact identification, the required sensitivity is guaranteed by simply exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor is exploited to detect the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a good agreement between experimental and simulated results for both active and passive impact monitoring scenarios. PMID:28773154

Inspection Correlation Study of Ultrasonic-Based In Situ Structural Health Monitoring Monthly Report for December 2014-January 2015

DTIC Science & Technology

2015-05-01

fatigue an induced ultrasonic elastic vibration (via piezoelectric transducers [ PZTs ]) propagates through the dogbone specimen. A receiver PZT picks up...inspection of fatigue crack growth in aluminum 7075-T6 dogbone specimens. Acellent Technologies, Inc., is supporting this project through providing...January 2015. 15. SUBJECT TERMS structural health monitoring, probabilistics, fatigue damage, guided waves, Lamb waves 16. SECURITY CLASSIFICATION OF

A Multi-Scale Structural Health Monitoring Approach for Damage Detection, Diagnosis and Prognosis in Aerospace Structures

DTIC Science & Technology

2012-01-20

ultrasonic Lamb waves to plastic strain and fatigue life. Theory was developed and validated to predict second harmonic generation for specific mode... Fatigue and damage generation and progression are processes consisting of a series of interrelated events that span large scales of space and time...strain and fatigue life A set of experiments were completed that worked to relate the acoustic nonlinearity measured with Lamb waves to both the

Design of a piezoelectric-based structural health monitoring system for damage detection in composite materials

NASA Astrophysics Data System (ADS)

Kessler, Seth S.; Spearing, S. Mark

2002-07-01

Cost-effective and reliable damage detection is critical for the utilization of composite materials. This paper presents the conclusions of an experimental and analytical survey of candidate methods for in-situ damage detection in composite structures. Experimental results are presented for the application of modal analysis and Lamb wave techniques to quasi-isotropic graphite/epoxy test specimens containing representative damage. Piezoelectric patches were used as actuators and sensors for both sets of experiments. Modal analysis methods were reliable for detecting small amounts of global damage in a simple composite structure. By comparison, Lamb wave methods were sensitive to all types of local damage present between the sensor and actuator, provided useful information about damage presence and severity, and present the possibility of estimating damage type and location. Analogous experiments were also performed for more complex built-up structures. These techniques are suitable for structural health monitoring applications since they can be applied with low power conformable sensors and can provide useful information about the state of a structure during operation. Piezoelectric patches could also be used as multipurpose sensors to detect damage by a variety of methods such as modal analysis, Lamb wave, acoustic emission and strain based methods simultaneously, by altering driving frequencies and sampling rates. This paper present guidelines and recommendations drawn from this research to assist in the design of a structural health monitoring system for a vehicle. These systems will be an important component in future designs of air and spacecraft to increase the feasibility of their missions.

Pulse based sensor networking using mechanical waves through metal substrates

NASA Astrophysics Data System (ADS)

Lorenz, S.; Dong, B.; Huo, Q.; Tomlinson, W. J.; Biswas, S.

2013-05-01

This paper presents a novel wireless sensor networking technique using ultrasonic signal as the carrier wave for binary data exchange. Using the properties of lamb wave propagation through metal substrates, the proposed network structure can be used for runtime transport of structural fault information to ultrasound access points. Primary applications of the proposed sensor networking technique will include conveying fault information on an aircraft wing or on a bridge to an ultrasonic access point using ultrasonic wave through the structure itself (i.e. wing or bridge). Once a fault event has been detected, a mechanical pulse is forwarded to the access node using shortest path multi-hop ultrasonic pulse routing. The advantages of mechanical waves over traditional radio transmission using pulses are the following: First, unlike radio frequency, surface acoustic waves are not detectable outside the medium, which increases the inherent security for sensitive environments in respect to tapping. Second, event detection can be represented by the injection of a single mechanical pulse at a specific temporal position, whereas radio messages usually take several bits. The contributions of this paper are: 1) Development of a transceiver for transmitting/receiving ultrasound pulses with a pulse loss rate below 2·10-5 and false positive rate with an upper bound of 2·10-4. 2) A novel one-hop distance estimation based on the properties of lamb wave propagation with an accuracy of above 80%. 3) Implementation of a wireless sensor network using mechanical wave propagation for event detection on a 2024 aluminum alloy commonly used for aircraft skin construction.

Temperature effects in ultrasonic Lamb wave structural health monitoring systems.

PubMed

Lanza di Scalea, Francesco; Salamone, Salvatore

2008-07-01

There is a need to better understand the effect of temperature changes on the response of ultrasonic guided-wave pitch-catch systems used for structural health monitoring. A model is proposed to account for all relevant temperature-dependent parameters of a pitch-catch system on an isotropic plate, including the actuator-plate and plate-sensor interactions through shear-lag behavior, the piezoelectric and dielectric permittivity properties of the transducers, and the Lamb wave dispersion properties of the substrate plate. The model is used to predict the S(0) and A(0) response spectra in aluminum plates for the temperature range of -40-+60 degrees C, which accounts for normal aircraft operations. The transducers examined are monolithic PZT-5A [PZT denotes Pb(Zr-Ti)O3] patches and flexible macrofiber composite type P1 patches. The study shows substantial changes in Lamb wave amplitude response caused solely by temperature excursions. It is also shown that, for the transducers considered, the response amplitude changes follow two opposite trends below and above ambient temperature (20 degrees C), respectively. These results can provide a basis for the compensation of temperature effects in guided-wave damage detection systems.

Negative group velocity Lamb waves on plates and applications to the scattering of sound by shells

NASA Astrophysics Data System (ADS)

Marston, Philip L.

2003-05-01

Symmetric Lamb waves on plates exhibit anomalies for certain regions of frequency. The phase velocity appears to be double-valued [M. F. Werby and H. Überall, J. Acoust. Soc. Am. 111, 2686-2691 (2002)] with one of the branches having a negative group velocity relative to the corresponding phase velocity. The classification of the symmetric plate modes for frequencies appearing to have a double-valued phase velocity is reviewed here. The complication of a double-valued velocity is avoided by examining mode orthogonality and the complex wave-number spectra. Various authors have noted an enhancement in the backscattering of sound by elastic shells in water that occurs for frequencies where symmetric leaky Lamb waves (generalized to case of a shell) have contra-directed group and phase velocities. The ray diagram for negative group velocity contributions to the scattering by shells [G. Kaduchak, D. H. Hughes, and P. L. Marston, J. Acoust. Soc. Am. 96, 3704-3714 (1994)] is unusual since for this type of mode the energy on the shell flows in the opposite direction of the wave vector. Circumnavigation of the shell is not required for the leaky ray to be backward directed.

Analysis of Rayleigh-Lamb Modes in Soft-solids with Application to Surface Wave Elastography

NASA Astrophysics Data System (ADS)

Benech, Nicolás; Grinspan, Gustavo; Aguiar, Sofía; Brum, Javier; Negreira, Carlos; tanter, Mickäel; Gennisson, Jean-Luc

The goal of Surface Wave Elastography (SE) techniques is to estimate the shear elasticity of the sample by measuring the surface wave speed. In SE the thickness of the sample is often assumed to be infinite, in this way, the surface wave speed is directly linked to the sample's shear elasticity. However for many applications this assumption is not true. In this work, we study experimentally the Rayleigh-Lamb modes in soft solids of finite thickness to explore the optimal conditions for SWE. Experiments were carried out in three tissue mimicking phantoms of different thicknesses (10 mm, 20 mm and 60 mm) and same shear elasticity. The surface waves were generated at the surface of the phantom using piston attached to a mechanical vibrator. The central frequency of the excitation was varied between 60 Hz to 160 Hz. One component of the displacement field generated by the piston was measured at the surface and in the bulk of the sample trough a standard speckle tracking technique using a 256 element, 7.5 MHz central frequency linear array and an ultrasound ultrafast electronics. Finally, by measuring the phase velocity at each excitation frequency, velocity dispersion curves were obtained for each phantom. The results show that instead of a Rayleigh wave, zero order symmetric (S0) and antisymmetric (A0) Lamb modes are excited with this type of source. Moreover, in this study we show that due to the near field effects of the source, which are appreciable only in soft solids at low frequencies, both Lamb modes are separable in time and space. We show that while the Ao mode dominates close the source, the S0 mode dominates far away.

Acousto-optic modulation of a photonic crystal nanocavity with Lamb waves in microwave K band

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tadesse, Semere A.; School of Physics and Astronomy, University of Minnesota, Minneapolis, Minnesota 55455; Li, Huan

2015-11-16

Integrating nanoscale electromechanical transducers and nanophotonic devices potentially can enable acousto-optic devices to reach unprecedented high frequencies and modulation efficiency. Here, we demonstrate acousto-optic modulation of a photonic crystal nanocavity using Lamb waves with frequency up to 19 GHz, reaching the microwave K band. The devices are fabricated in suspended aluminum nitride membrane. Excitation of acoustic waves is achieved with interdigital transducers with period as small as 300 nm. Confining both acoustic wave and optical wave within the thickness of the membrane leads to improved acousto-optic modulation efficiency in these devices than that obtained in previous surface acoustic wave devices. Ourmore » system demonstrates a scalable optomechanical platform where strong acousto-optic coupling between cavity-confined photons and high frequency traveling phonons can be explored.« less

Surface Brillouin scattering study of the surface excitations in amorphous silicon layers produced by ion bombardment

NASA Astrophysics Data System (ADS)

Zhang, X.; Comins, J. D.; Every, A. G.; Stoddart, P. R.; Pang, W.; Derry, T. E.

1998-11-01

Thin amorphous silicon layers on crystalline silicon substrates have been produced by argon-ion bombardment of (001) silicon surfaces. Thermally induced surface excitations characteristic of this example of a soft-on-hard system have been investigated by surface Brillouin scattering (SBS) as a function of scattering-angle and amorphous-layer thickness. At large scattering angles or for sufficiently large layer thickness, a second peak is present in the SBS spectrum near the low-energy threshold for the continuum of bulk excitations of the system. The measured spectra are analyzed on the basis of surface elastodynamic Green's functions, which successfully simulate their detailed appearance and identify the second peak as either a Sezawa wave (true surface wave) or a pseudo-Sezawa wave (attenuated surface wave) depending on the scattering parameters. The attributes of the pseudo-Sezawa wave are described; these include its asymmetrical line shape and variation in intensity with k∥d (the product of the surface excitation wave vector and the layer thickness), and its emergence as the Sezawa wave from the low-energy side of the Lamb shoulder at a critical value of k∥d. Furthermore, the behavior of a pronounced minimum in the Lamb shoulder near the longitudinal wave threshold observed in the experiments is reported and is found to be in good agreement with the calculated spectra. The elastic constants of the amorphous silicon layer are determined from the velocity dispersion of the Rayleigh surface acoustic wave and the minimum in the Lamb shoulder.

Lamb Wave Propagation in a Restricted Geometry Composite PI-Joint Specimen (Preprint)

DTIC Science & Technology

2011-11-01

adhesive, and were located along the length and height of the specimen as depicted in Figure 3. The sensors were 6.35 mm round disks of PZT , with a...in both cases for R1, R2, and R3. 3D Finite Element Model Geometry 200mm length 50mm width 140mm height x z y PZT Actuation Sensor...health monitoring using scanning laser vibrometry: III. Lamb waves for fatigue crack detection”, Smart Mater. Struct., Vol. 14, No. 6, 2005. 16

Non-invasive thermal profiling of silicon wafer surface during RTP using acoustic and signal processing techniques

NASA Astrophysics Data System (ADS)

Syed, Ahmed Rashid

Among the great physical challenges faced by the current front-end semiconductor equipment manufacturers is the accurate and repeatable surface temperature measurement of wafers during various fabrication steps. Close monitoring of temperature is essential in that it ensures desirable device characteristics to be reliably reproduced across various wafer lots. No where is the need to control temperature more pronounced than it is during Rapid Thermal Processing (RTP) which involves temperature ramp rates in excess of 200°C/s. This dissertation presents an elegant and practical approach to solve the wafer surface temperature estimation problem, in context of RTP, by deploying hardware that acquires the necessary data while preserving the integrity and purity of the wafer. In contrast to the widely used wafer-contacting (and hence contaminating) methods, such as bonded thermocouples, or environment sensitive schemes, such as light-pipes and infrared pyrometry, the proposed research explores the concept of utilizing Lamb (acoustic) waves to detect changes in wafer surface temperature, during RTP. Acoustic waves are transmitted to the wafer via an array of quartz rods that normally props the wafer inside an RTP chamber. These waves are generated using piezoelectric transducers affixed to the bases of the quartz rods. The group velocity of Lamb waves traversing the wafer surface undergoes a monotonic decrease with rise in wafer temperature. The correspondence of delay in phase of the received Lamb waves and the ambient temperature, along all direct paths between sending and receiving transducers, yields a psuedo real-time thermal image of the wafer. Although the custom built hardware-setup implements the above "proof-of-concept" scheme by transceiving acoustic signals at a single frequency, the real-world application will seek to enhance the data acquistion. rate (>1000 temperature measurements per seconds) by sending and receiving Lamb waves at multiple frequencies (by employing broadband quartz rod-transducer assembles). Experimental results, as predicted by prior rigorous simulations, prove that the temperature measurement accuracy obtained through several dynamic runs using the above specified approach, is better than +/-2°C. Furthermore, these results are highly repeatable and independent of wafer treatment conditions, thereby extolling the versatility and immunity of the new method from environmental conditions.

On-line crack prognosis in attachment lug using Lamb wave-deterministic resampling particle filter-based method

NASA Astrophysics Data System (ADS)

Yuan, Shenfang; Chen, Jian; Yang, Weibo; Qiu, Lei

2017-08-01

Fatigue crack growth prognosis is important for prolonging service time, improving safety, and reducing maintenance cost in many safety-critical systems, such as in aircraft, wind turbines, bridges, and nuclear plants. Combining fatigue crack growth models with the particle filter (PF) method has proved promising to deal with the uncertainties during fatigue crack growth and reach a more accurate prognosis. However, research on prognosis methods integrating on-line crack monitoring with the PF method is still lacking, as well as experimental verifications. Besides, the PF methods adopted so far are almost all sequential importance resampling-based PFs, which usually encounter sample impoverishment problems, and hence performs poorly. To solve these problems, in this paper, the piezoelectric transducers (PZTs)-based active Lamb wave method is adopted for on-line crack monitoring. The deterministic resampling PF (DRPF) is proposed to be used in fatigue crack growth prognosis, which can overcome the sample impoverishment problem. The proposed method is verified through fatigue tests of attachment lugs, which are a kind of important joint component in aerospace systems.

Guided wave propagation in metallic and resin plates loaded with water on single surface

NASA Astrophysics Data System (ADS)

Hayashi, Takahiro; Inoue, Daisuke

2016-02-01

Our previous papers reported dispersion curves for leaky Lamb waves in a water-loaded plate and wave structures for several typical modes including quasi-Scholte waves [1,2]. The calculations were carried out with a semi-analytical finite element (SAFE) method developed for leaky Lamb waves. This study presents SAFE calculations for transient guided waves including time-domain waveforms and animations of wave propagation in metallic and resin water-loaded plates. The results show that non-dispersive and non-attenuated waves propagating along the interface between the fluid and the plate are expected for effective non-destructive evaluation of such fluid-loaded plates as storage tanks and transportation pipes. We calculated transient waves in both steel and polyvinyl chloride (PVC) plates loaded with water on a single side and input dynamic loading from a point source on the other water-free surface as typical examples of metallic and resin plates. For a steel plate, there exists a non-dispersive and non-attenuated mode, called the quasi-Scholte wave, having an almost identical phase velocity to that of water. The quasi-Scholte wave has superior generation efficiency in the low frequency range due to its broad energy distribution across the plate, whereas it is localized near the plate-water interface at higher frequencies. This means that it has superior detectability of inner defects. For a PVC plate, plural non-attenuated modes exist. One of the non-attenuated modes similar to the A0 mode of the Lamb wave in the form of a group velocity dispersion curve is promising for the non-destructive evaluation of the PVC plate because it provides prominent characteristics of generation efficiency and low dispersion.

Directional nonlinear guided wave mixing: Case study of counter-propagating shear horizontal waves

NASA Astrophysics Data System (ADS)

Hasanian, Mostafa; Lissenden, Cliff J.

2018-04-01

While much nonlinear ultrasonics research has been conducted on higher harmonic generation, wave mixing provides the potential for sensitive measurements of incipient damage unencumbered by instrumentation nonlinearity. Studies of nonlinear ultrasonic wave mixing, both collinear and noncollinear, for bulk waves have shown the robust capability of wave mixing for early damage detection. One merit of bulk wave mixing lies in their non-dispersive nature, but guided waves enable inspection of otherwise inaccessible material and a variety of mixing options. Co-directional guided wave mixing was studied previously, but arbitrary direction guided wave mixing has not been addressed until recently. Wave vector analysis is applied to study variable mixing angles to find wave mode triplets (two primary waves and a secondary wave) resulting in the phase matching condition. As a case study, counter-propagating Shear Horizontal (SH) guided wave mixing is analyzed. SH wave interactions generate a secondary Lamb wave mode that is readily receivable. Reception of the secondary Lamb wave mode is compared for an angle beam transducer, an air coupled transducer, and a laser Doppler vibrometer (LDV). Results from the angle beam and air coupled transducers are quite consistent, while the LDV measurement is plagued by variability issues.

Development of smart piezoelectric transducer self-sensing, self-diagnosis and tuning schemes for structural health monitoring applications

NASA Astrophysics Data System (ADS)

Lee, Sang Jun

Autonomous structural health monitoring (SHM) systems using active sensing devices have been studied extensively to diagnose the current state of aerospace, civil infrastructure and mechanical systems in near real-time and aims to eventually reduce life-cycle costs by replacing current schedule-based maintenance with condition-based maintenance. This research develops four schemes for SHM applications: (1) a simple and reliable PZT transducer self-sensing scheme; (2) a smart PZT self-diagnosis scheme; (3) an instantaneous reciprocity-based PZT diagnosis scheme; and (4) an effective PZT transducer tuning scheme. First, this research develops a PZT transducer self-sensing scheme, which is a necessary condition to accomplish a PZT transducer self-diagnosis. Main advantages of the proposed self-sensing approach are its simplicity and adaptability. The necessary hardware is only an additional self-sensing circuit which includes a minimum of electric components. With this circuit, the self-sensing parameters can be calibrated instantaneously in the presence of changing operational and environmental conditions of the system. In particular, this self-sensing scheme focuses on estimating the mechanical response in the time domain for the subsequent applications of the PZT transducer self-diagnosis and tuning with guided wave propagation. The most significant challenge of this self-sensing comes from the fact that the magnitude of the mechanical response is generally several orders of magnitude smaller than that of the input signal. The proposed self-sensing scheme fully takes advantage of the fact that any user-defined input signals can be applied to a host structure and the input waveform is known. The performance of the proposed self-sensing scheme is demonstrated by theoretical analysis, numerical simulations and various experiments. Second, this research proposes a smart PZT transducer self-diagnosis scheme based on the developed self-sensing scheme. Conventionally, the capacitance change of the PZT wafer is monitored to identify the abnormal PZT condition because the capacitance of the PZT wafer is linearly proportional to its size and also related to the bonding condition. However, temperature variation is another primary factor that affects the PZT capacitance. To ensure the reliable transducer self-diagnosis, two different self-diagnosis features are proposed to differentiate two main PZT wafer defects, i.e., PZT debonding and PZT cracking, from temperature variations and structural damages. The PZT debonding is identified using two indices based on time reversal process (TRP) without any baseline data. Also, the PZT cracking is identified by monitoring the change of the generated Lamb wave power ratio index with respect to the driving frequency. The uniqueness of this self-diagnosis scheme is that the self-diagnosis features can differentiate the PZT defects from environmental variations and structural damages. Therefore, it is expected to minimize false-alarms which are induced by operational or environmental variations as well as structural damages. The applicability of the proposed self-diagnosis scheme is verified by theoretical analysis, numerical simulations, and experimental tests. Third, a new methodology of guided wave-based PZT transducer diagnosis is developed to identify PZT transducer defects without using prior baseline data. This methodology can be applied when a number of same-size PZT transducers are attached to a target structure to form a sensor network. The advantage of the proposed technique is that abnormal PZT transducers among intact PZT transducers can be detected even when the system being monitored is subjected to varying operational and environmental conditions or changing structural conditions. To achieve this goal, the proposed diagnosis technique utilizes the linear reciprocity of guided wave propagation between a pair of surface-bonded PZT transducers. Finally, a PZT transducer tuning scheme is being developed for selective Lamb wave excitation and sensing. This is useful for structural damage detection based on Lamb wave propagation because the proper transducer size and the corresponding input frequency can be is crucial for selective Lamb wave excitation and sensing. The circular PZT response model is derived, and the energy balance is included for a better prediction of the PZT responses because the existing PZT response models do not consider any energy balance between Lamb wave modes. In addition, two calibration methods are also suggested in order to model the PZT responses more accurately by considering a bonding layer effect. (Abstract shortened by UMI.)

Bi-directional ultrasonic wave coupling to FBGs in continuously bonded optical fiber sensing.

PubMed

Wee, Junghyun; Hackney, Drew; Bradford, Philip; Peters, Kara

2017-09-01

Fiber Bragg grating (FBG) sensors are typically spot-bonded onto the surface of a structure to detect ultrasonic waves in laboratory demonstrations. However, to protect the rest of the optical fiber from any environmental damage during real applications, bonding the entire length of fiber, called continuous bonding, is commonly done. In this paper, we investigate the impact of continuously bonding FBGs on the measured Lamb wave signal. In theory, the ultrasonic wave signal can bi-directionally transfer between the optical fiber and the plate at any adhered location, which could potentially produce output signal distortion for the continuous bonding case. Therefore, an experiment is performed to investigate the plate-to-fiber and fiber-to-plate signal transfer, from which the signal coupling coefficient of each case is theoretically estimated based on the experimental data. We demonstrate that the two coupling coefficients are comparable, with the plate-to-fiber case approximately 19% larger than the fiber-to-plate case. Finally, the signal waveform and arrival time of the output FBG responses are compared between the continuous and spot bonding cases. The results indicate that the resulting Lamb wave signal output is only that directly detected at the FBG location; however, a slight difference in signal waveform is observed between the two bonding configurations. This paper demonstrates the practicality of using continuously bonded FBGs for ultrasonic wave detection in structural health monitoring (SHM) applications.

Quantitative damage imaging using Lamb wave diffraction tomography

NASA Astrophysics Data System (ADS)

Zhang, Hai-Yan; Ruan, Min; Zhu, Wen-Fa; Chai, Xiao-Dong

2016-12-01

In this paper, we investigate the diffraction tomography for quantitative imaging damages of partly through-thickness holes with various shapes in isotropic plates by using converted and non-converted scattered Lamb waves generated numerically. Finite element simulations are carried out to provide the scattered wave data. The validity of the finite element model is confirmed by the comparison of scattering directivity pattern (SDP) of circle blind hole damage between the finite element simulations and the analytical results. The imaging method is based on a theoretical relation between the one-dimensional (1D) Fourier transform of the scattered projection and two-dimensional (2D) spatial Fourier transform of the scattering object. A quantitative image of the damage is obtained by carrying out the 2D inverse Fourier transform of the scattering object. The proposed approach employs a circle transducer network containing forward and backward projections, which lead to so-called transmission mode (TMDT) and reflection mode diffraction tomography (RMDT), respectively. The reconstructed results of the two projections for a non-converted S0 scattered mode are investigated to illuminate the influence of the scattering field data. The results show that Lamb wave diffraction tomography using the combination of TMDT and RMDT improves the imaging effect compared with by using only the TMDT or RMDT. The scattered data of the converted A0 mode are also used to assess the performance of the diffraction tomography method. It is found that the circle and elliptical shaped damages can still be reasonably identified from the reconstructed images while the reconstructed results of other complex shaped damages like crisscross rectangles and racecourse are relatively poor. Project supported by the National Natural Science Foundation of China (Grant Nos. 11474195, 11274226, 11674214, and 51478258).

Experimental and theoretical study of Rayleigh-Lamb waves in a plate containing a surface-breaking crack

NASA Technical Reports Server (NTRS)

Paffenholz, Joseph; Fox, Jon W.; Gu, Xiaobai; Jewett, Greg S.; Datta, Subhendu K.

1990-01-01

Scattering of Rayleigh-Lamb waves by a normal surface-breaking crack in a plate has been studied both theoretically and experimentally. The two-dimensionality of the far field, generated by a ball impact source, is exploited to characterize the source function using a direct integration technique. The scattering of waves generated by this impact source by the crack is subsequently solved by employing a Green's function integral expression for the scattered field coupled with a finite element representation of the near field. It is shown that theoretical results of plate response, both in frequency and time, are similar to those obtained experimentally. Additionally, implication for practical applications are discussed.

Comparative study of electromechanical impedance and Lamb wave techniques for fatigue crack detection and monitoring in metallic structures

NASA Astrophysics Data System (ADS)

Lim, Say Ian; Liu, Yu; Soh, Chee Kiong

2012-04-01

Fatigue cracks often initiate at the weld toes of welded steel connections. Usually, these cracks cannot be identified by the naked eyes. Existing identification methods like dye-penetration test and alternating current potential drop (ACPD) may be useful for detecting fatigue cracks at the weld toes. To apply these non-destructive evaluation (NDE) techniques, the potential sites have to be accessible during inspection. Therefore, there is a need to explore other detection and monitoring techniques for fatigue cracks especially when their locations are inaccessible or cost of access is uneconomical. Electro-mechanical Impedance (EMI) and Lamb wave techniques are two fast growing techniques in the Structural Health Monitoring (SHM) community. These techniques use piezoelectric ceramics (PZT) for actuation and sensing. Since the monitoring site is only needed to be accessed once for the instrumentation of the transducers, remote monitoring is made possible. The permanent locations of these transducers also translate to having consistent measurement for monitoring. The main focus of this study is to conduct a comparative investigation on the effectiveness and efficiency of the EMI technique and the Lamb wave technique for successful fatigue crack identification and monitoring of welded steel connections using piezoelectric transducers. A laboratory-sized non-load carrying fillet weld specimen is used in this study. The specimen is subjected to cyclic tensile load and data for both techniques are acquired at stipulated intervals. It can be concluded that the EMI technique is sensitive to the crack initiation phase while the Lamb wave technique correlates well with the crack propagation phase.

Reflection and transmission coefficients for guided waves reflected by defects in viscoelastic material plates.

PubMed

Hosten, Bernard; Moreau, Ludovic; Castaings, Michel

2007-06-01

The paper presents a Fourier transform-based signal processing procedure for quantifying the reflection and transmission coefficients and mode conversion of guided waves diffracted by defects in plates made of viscoelastic materials. The case of the S(0) Lamb wave mode incident on a notch in a Perspex plate is considered. The procedure is applied to numerical data produced by a finite element code that simulates the propagation of attenuated guided modes and their diffraction by the notch, including mode conversion. Its validity and precision are checked by the way of the energy balance computation and by comparison with results obtained using an orthogonality relation-based processing method.

Numerical predictions and experiments for optimizing hidden corrosion detection in aircraft structures using Lamb modes.

PubMed

Terrien, N; Royer, D; Lepoutre, F; Déom, A

2007-06-01

To increase the sensitivity of Lamb waves to hidden corrosion in aircraft structures, a preliminary step is to understand the phenomena governing this interaction. A hybrid model combining a finite element approach and a modal decomposition method is used to investigate the interaction of Lamb modes with corrosion pits. The finite element mesh is used to describe the region surrounding the corrosion pits while the modal decomposition method permits to determine the waves reflected and transmitted by the damaged area. Simulations make easier the interpretation of some parts of the measured waveform corresponding to superposition of waves diffracted by the corroded area. Numerical results permit to extract significant information from the transmitted waveform and thus to optimize the signal processing for the detection of corrosion at an early stage. Now, we are able to detect corrosion pits down to 80-mum depth distributed randomly on a square centimeter of an aluminum plate. Moreover, thickness variations present on aircraft structures can be discriminated from a slightly corroded area. Finally, using this experimental setup, aircraft structures have been tested.

Characterization of Ultrasound Energy Diffusion Due to Small-Size Damage on an Aluminum Plate Using Piezoceramic Transducers

PubMed Central

Lu, Guangtao; Feng, Qian; Li, Yourong; Wang, Hao; Song, Gangbing

2017-01-01

During the propagation of ultrasonic waves in structures, there is usually energy loss due to ultrasound energy diffusion and dissipation. The aim of this research is to characterize the ultrasound energy diffusion that occurs due to small-size damage on an aluminum plate using piezoceramic transducers, for the future purpose of developing a damage detection algorithm. The ultrasonic energy diffusion coefficient is related to the damage distributed in the medium. Meanwhile, the ultrasonic energy dissipation coefficient is related to the inhomogeneity of the medium. Both are usually employed to describe the characteristics of ultrasound energy diffusion. The existence of multimodes of Lamb waves in metallic plate structures results in the asynchronous energy transport of different modes. The mode of Lamb waves has a great influence on ultrasound energy diffusion as a result, and thus has to be chosen appropriately. In order to study the characteristics of ultrasound energy diffusion in metallic plate structures, an experimental setup of an aluminum plate with a through-hole, whose diameter varies from 0.6 mm to 1.2 mm, is used as the test specimen with the help of piezoceramic transducers. The experimental results of two categories of damages at different locations reveal that the existence of damage changes the energy transport between the actuator and the sensor. Also, when there is only one dominate mode of Lamb wave excited in the structure, the ultrasound energy diffusion coefficient decreases approximately linearly with the diameter of the simulated damage. Meanwhile, the ultrasonic energy dissipation coefficient increases approximately linearly with the diameter of the simulated damage. However, when two or more modes of Lamb waves are excited, due to the existence of different group velocities between the different modes, the energy transport of the different modes is asynchronous, and the ultrasonic energy diffusion is not strictly linear with the size of the damage. Therefore, it is recommended that only one dominant mode of Lamb wave should be excited during the characterization process, in order to ensure that the linear relationship between the damage size and the characteristic parameters is maintained. In addition, the findings from this paper demonstrate the potential of developing future damage detection algorithms using the linear relationships between damage size and the ultrasound energy diffusion coefficient or ultrasonic energy dissipation coefficient when a single dominant mode is excited. PMID:29207530

Dispersion of Lamb waves in a honeycomb composite sandwich panel.

PubMed

Baid, Harsh; Schaal, Christoph; Samajder, Himadri; Mal, Ajit

2015-02-01

Composite materials are increasingly being used in advanced aircraft and aerospace structures. Despite their many advantages, composites are often susceptible to hidden damages that may occur during manufacturing and/or service of the structure. Therefore, safe operation of composite structures requires careful monitoring of the initiation and growth of such defects. Ultrasonic methods using guided waves offer a reliable and cost effective method for defects monitoring in advanced structures due to their long propagation range and their sensitivity to defects in their propagation path. In this paper, some of the useful properties of guided Lamb type waves are investigated, using analytical, numerical and experimental methods, in an effort to provide the knowledge base required for the development of viable structural health monitoring systems for composite structures. The laboratory experiments involve a pitch-catch method in which a pair of movable transducers is placed on the outside surface of the structure for generating and recording the wave signals. The specific cases considered include an aluminum plate, a woven composite laminate and an aluminum honeycomb sandwich panel. The agreement between experimental, numerical and theoretical results are shown to be excellent in certain frequency ranges, providing a guidance for the design of effective inspection systems. Copyright © 2014 Elsevier B.V. All rights reserved.

Numerical and experimental simulation of linear shear piezoelectric phased arrays for structural health monitoring

NASA Astrophysics Data System (ADS)

Wang, Wentao; Zhang, Hui; Lynch, Jerome P.; Cesnik, Carlos E. S.; Li, Hui

2017-04-01

A novel d36-type piezoelectric wafer fabricated from lead magnesium niobate-lead titanate (PMN-PT) is explored for the generation of in-plane horizontal shear waves in plate structures. The study focuses on the development of a linear phased array (PA) of PMN-PT wafers to improve the damage detection capabilities of a structural health monitoring (SHM) system. An attractive property of in-plane horizontal shear waves is that they are nondispersive yet sensitive to damage. This study characterizes the directionality of body waves (Lamb and horizontal shear) created by a single PMN-PT wafer bonded to the surface of a metallic plate structure. Second, a linear PA is designed from PMN-PT wafers to steer and focus Lamb and horizontal shear waves in a plate structure. Numerical studies are conducted to explore the capabilities of a PMN-PT-based PA to detect damage in aluminum plates. Numerical simulations are conducted using the Local Interaction Simulation Approach (LISA) implemented on a parallelized graphical processing unit (GPU) for high-speed execution. Numerical studies are further validated using experimental tests conducted with a linear PA. The study confirms the ability of an PMN-PT phased array to accurately detect and localize damage in aluminum plates.

Scattering matrices of Lamb waves at irregular surface and void defects.

PubMed

Feng, Feilong; Shen, Jianzhong; Lin, Shuyu

2012-08-01

Time-harmonic solution of Lamb wave scattering in a plane-strain waveguide with irregular thickness is investigated based on stair-step discretization and stepwise mode matching. The transfer relations of the transmission matrices and reflection matrices are derived in both directions of the waveguide. With these, an explicit expression of the scattering matrix is derived. When the scattering region of an inner irregular defect is geometrically divided into several parts composed of sub-waveguides with variable thicknesses and void regions with vertical free edges corresponding to the plate surfaces, the scattering matrix of the whole region could then be derived by modal matching along the artificial boundaries, as explicit functions of all the scattering matrices of the sub-waveguides and reflection matrices of the free edges. The effectiveness of the formulation is examined by numerical examples; the calculated scattering coefficients are in good accordance with those obtained from numerical simulation models. Copyright © 2012 Elsevier B.V. All rights reserved.

Simulations on Monitoring and Evaluation of Plasticity-Driven Material Damage Based on Second Harmonic of S0 Mode Lamb Waves in Metallic Plates

PubMed Central

Sun, Xiaoqiang; Liu, Xuyang; Liu, Yaolu; Hu, Ning; Zhao, Youxuan; Ding, Xiangyan; Qin, Shiwei; Zhang, Jianyu; Zhang, Jun; Liu, Feng; Fu, Shaoyun

2017-01-01

In this study, a numerical approach—the discontinuous Meshless Local Petrov-Galerkin-Eshelby Method (MLPGEM)—was adopted to simulate and measure material plasticity in an Al 7075-T651 plate. The plate was modeled in two dimensions by assemblies of small particles that interact with each other through bonding stiffness. The material plasticity of the model loaded to produce different levels of strain is evaluated with the Lamb waves of S0 mode. A tone burst at the center frequency of 200 kHz was used as excitation. Second-order nonlinear wave was extracted from the spectrogram of a signal receiving point. Tensile-driven plastic deformation and cumulative second harmonic generation of S0 mode were observed in the simulation. Simulated measurement of the acoustic nonlinearity increased monotonically with the level of tensile-driven plastic strain captured by MLPGEM, whereas achieving this state by other numerical methods is comparatively more difficult. This result indicates that the second harmonics of S0 mode can be employed to monitor and evaluate the material or structural early-stage damage induced by plasticity. PMID:28773188

Non-collinear interaction of guided elastic waves in an isotropic plate

NASA Astrophysics Data System (ADS)

Ishii, Yosuke; Biwa, Shiro; Adachi, Tadaharu

2018-04-01

The nonlinear wave propagation in a homogeneous and isotropic elastic plate is analyzed theoretically to investigate the non-collinear interaction of plate wave modes. In the presence of two primary plate waves (Rayleigh-Lamb or shear horizontal modes) propagating in arbitrary directions, an explicit expression for the modal amplitude of nonlinearly generated wave fields with the sum or difference frequency of the primary modes is derived by using the perturbation analysis. The modal amplitude is shown to grow in proportion with the propagation distance when the resonance condition is satisfied, i.e., when the wavevector of secondary wave coincides with the sum or difference of those of primary modes. Furthermore, the non-collinear interaction of two symmetric or two antisymmetric modes is shown to produce the secondary wave fields consisting only of the symmetric modes, while a pair of symmetric and antisymmetric primary modes is shown to produce only the antisymmetric modes. The influence of the intersection angle, the primary frequencies, and the mode combinations on the modal amplitude of secondary wave is examined for a low-frequency range where the lowest-order symmetric and antisymmetric Rayleigh-Lamb waves and the lowest-order symmetric shear horizontal wave are the only propagating modes.

Re-radiation of acoustic waves from the A0 wave on a submerged elastic shell

NASA Astrophysics Data System (ADS)

Ahyi, A. C.; Cao, Hui; Raju, P. K.; Überall, Herbert

2005-07-01

We consider evacuated thin semi-infinite shells immersed in a fluid, which may be either of cylindrical shape with a hemispherical shell endcap, or formed two-dimensionally by semi-infinite parallel plates joined together by a semi-cylinder. The connected shell portions are joined in a manner to satisfy continuity but with a discontinuous radius of curvature. Acoustic waves are considered incident along the axis of symmetry (say the z axis) onto the curved portion of the shell, where they, at the critical angle of coincidence, generate Lamb and Stoneley-type waves in the shell. Computations were carried out using a code developed by Cao et al. [Chinese J. Acoust. 14, 317 (1995)] and was used in order to computationally visualize the waves in the fluid that have been re-radiated by the shell waves a the critical angle. The frequency range was below that of the lowest Lamb wave, and only the A0 wave (and partly the S0 wave) was observed to re-radiate into the fluid under our assumptions. The results will be compared to experimental results in which the re-radiated waves are optically visualized by the Schardin-Cranz schlieren method. .

Investigation of shock-acoustic-wave interaction in transonic flow

NASA Astrophysics Data System (ADS)

Feldhusen-Hoffmann, Antje; Statnikov, Vladimir; Klaas, Michael; Schröder, Wolfgang

2018-01-01

The buffet flow field around supercritical airfoils is dominated by self-sustained shock wave oscillations on the suction side of the wing. Theories assume that this unsteadiness is driven by an acoustic feedback loop of disturbances in the flow field downstream of the shock wave whose upstream propagating part is generated by acoustic waves. Therefore, in this study, first variations in the sound pressure level of the airfoil's trailing-edge noise during a buffet cycle, which force the shock wave to move upstream and downstream, are detected, and then, the sensitivity of the shock wave oscillation during buffet to external acoustic forcing is analyzed. Time-resolved standard and tomographic particle-image velocimetry (PIV) measurements are applied to investigate the transonic buffet flow field over a supercritical DRA 2303 airfoil. The freestream Mach number is M_{∞} = 0.73, the angle of attack is α = {3.5}°, and the chord-based Reynolds number is Re_c = 1.9× 10^6. The perturbed Lamb vector field, which describes the major acoustic source term of trailing-edge noise, is determined from the tomographic PIV data. Subsequently, the buffet flow field is disturbed by an artificially generated acoustic field, the acoustic intensity of which is comparable to the Lamb vector that is determined from the PIV data. The results confirm the hypothesis that buffet is driven by an acoustic feedback loop and show the shock wave oscillation to directly respond to external acoustic forcing. That is, the amplitude modulation frequency of the artificial acoustic perturbation determines the shock oscillation.

Lamb wave propagation in a restricted geometry composite pi-joint specimen

NASA Astrophysics Data System (ADS)

Blackshire, James L.; Soni, Som

2012-05-01

The propagation of elastic waves in a material can involve a number of complex physical phenomena, resulting in both subtle and dramatic effects on detected signal content. In recent years, the use of advanced methods for characterizing and imaging elastic wave propagation and scattering processes has increased, where for example the use of scanning laser vibrometry and advanced computational models have been used very effectively to identify propagating modes, scattering phenomena, and damage feature interactions. In the present effort, the propagation of Lamb waves within a narrow, constrained geometry composite pi-joint structure are studied using 3D finite element models and scanning laser vibrometry measurements, where the effects of varying sample thickness, complex joint curvatures, and restricted structure geometries are highlighted, and a direct comparison of computational and experimental results are provided for simulated and realistic geometry composite pi-joint samples.

Identification of delamination interface in composite laminates using scattering characteristics of lamb wave: numerical and experimental studies

NASA Astrophysics Data System (ADS)

Singh, Rakesh Kumar; Ramadas, C.; Balachandra Shetty, P.; Satyanarayana, K. G.

2017-04-01

Considering the superior strength properties of polymer based composites over metallic materials, they are being used in primary structures of aircrafts. However, these polymeric materials are much more complex in behaviour due to their structural anisotropy along with existence of different materials unlike in metallic alloys. These pose challenge in flaw detection, residual strength determination and life of a structure with their high susceptibility to impact damage in the form of delaminations/disbonds or cracks. This reduces load-bearing capability and potentially leads to structural failure. With this background, this study presents a method to identify location of delamination interface along thickness of a laminate. Both numerical and experimental studies have been carried out with a view to identify the defect, on propagation, mode conversion and scattering characteristics of fundamental anti-symmetric Lamb mode (Ao) when it passed through a semi-infinite delamination. Further, the reflection and transmission scattering coefficients based on power and amplitude ratios of the scattered waves have been computed. The methodology was applied on numerically simulated delaminations to illustrate the efficacy of the method. Results showed that it could successfully identify delamination interface.

Detection and assessment of flaws in friction stir welded joints using ultrasonic guided waves: experimental and finite element analysis

NASA Astrophysics Data System (ADS)

Fakih, Mohammad Ali; Mustapha, Samir; Tarraf, Jaafar; Ayoub, Georges; Hamade, Ramsey

2018-02-01

Ultrasonic guided waves (GWs), e.g. Lamb waves, have been proven effective in the detection of defects such as corrosion, cracking, delamination, and debonding in both composite and metallic structures. They are a significant tool employed in structural health monitoring. In this study, the ability of ultrasonic GWs to assess the quality of friction stir welding (FSW) was investigated. Four friction stir welded AZ31B magnesium plates processed with different welding parameters and a non-welded plate were used. The fundamental symmetric (S0) Lamb wave mode was excited using piezoelectric wafers (PZTs). Further, the S0 mode was separated using the "Improved complete ensemble empirical mode decomposition with adaptive noise (Improved CEEMDAN)" technique. A damage index (DI) was defined based on the variation in the amplitude of the captured wave signals in order to detect the presence and asses the severity of damage resulting from the welding process. As well, computed tomography (CT) scanning was used as a non-destructive testing (NDT) technique to assess the actual weld quality and validate predictions based on the GW approach. The findings were further confirmed using finite element analysis (FEA). To model the actual damage profile in the welds, "Mimics" software was used for the 3D reconstruction of the CT scans. The built 3D models were later used for evaluation of damage volume and for FEA. The damage volumes were correlated to the damage indices computed from both experimental and numerical data. The proposed approach showed high sensitivity of the S0 mode to internal flaws within the friction stir welded joints. This methodology has great potential as a future classification method of FSW quality.

One-way mode transmission in one-dimensional phononic crystal plates

NASA Astrophysics Data System (ADS)

Zhu, Xuefeng; Zou, Xinye; Liang, Bin; Cheng, Jianchun

2010-12-01

We investigate theoretically the band structures of one-dimensional phononic crystal (PC) plates with both antisymmetric and symmetric structures, and show how unidirectional transmission behavior can be obtained for either antisymmetric waves (A modes) or symmetric waves (S modes) by exploiting mode conversion and selection in the linear plate systems. The theoretical approach is illustrated for one PC plate example where unidirectional transmission behavior is obtained in certain frequency bands. Employing harmonic frequency analysis, we numerically demonstrate the one-way mode transmission for the PC plate with finite superlattice by calculating the steady-state displacement fields under A modes source (or S modes source) in forward and backward direction, respectively. The results show that the incident waves from A modes source (or S modes source) are transformed into S modes waves (or A modes waves) after passing through the superlattice in the forward direction and the Lamb wave rejections in the backward direction are striking with a power extinction ratio of more than 1000. The present structure can be easily extended to two-dimensional PC plate and efficiently encourage practical studies of experimental realization which is believed to have much significance for one-way Lamb wave mode transmission.

Experimental Investigation on Acousto-Ultrasonic Sensing Using Polarization-Maintaining Fiber Bragg Gratings

NASA Technical Reports Server (NTRS)

Wang, Gang; Banks, Curtis E.

2015-01-01

This report discusses the guided Lamb wave sensing using polarization-maintaining (PM) fiber Bragg grating (PM-FBG) sensor. The goal is to apply the PM-FBG sensor system to composite structural health monitoring (SHM) applications in order to realize directivity and multi-axis strain sensing capabilities while using reduced number of sensors. Comprehensive experiments were conducted to evaluate the performance of the PM-FBG sensor in a composite panel structure under different actuation frequencies and locations. Three Macro-Fiber-Composite (MFC) piezoelectric actuators were used to generate guided Lamb waves and they are oriented at 0, 45, and 90 degrees with respect to PM-FBG axial direction, respectively. The actuation frequency was varied from 20kHz to 200kHz. It is shown that the PM-FBG sensor system is able to detect high-speed ultrasound waves and capture the characteristics under different actuation conditions. Both longitudinal and lateral strain components in the order of nano-strain were determined based on the reflective intensity measurement data from fast and slow axis of the PM fiber. It must be emphasized that this is the first attempt to investigate acousto-ultrasonic sensing using PM-FBG sensor. This could lead to a new sensing approach in the SHM applications.

Experimental Investigation on Acousto-ultrasonic Sensing Using Polarization-Maintaining Fiber Bragg Gratings

NASA Technical Reports Server (NTRS)

Wang, Gag; Banks, Curtis E.

2016-01-01

This report discusses the guided Lamb wave sensing using polarization-maintaining (PM) fiber Bragg grating (PM-FBG) sensor. The goal is to apply the PM-FBG sensor system to composite structural health monitoring (SHM) applications in order to realize directivity and multi-axis strain sensing capabilities while reducing the number of sensors. Comprehensive experiments were conducted to evaluate the performance of the PM-FBG sensor attached to a composite panel structure under different actuation frequencies and locations. Three Macro-Fiber-Composite (MFC) piezoelectric actuators were used to generate guided Lamb waves that were oriented at 0, 45, and 90 degrees with respect to PM-FBG axial direction, respectively. The actuation frequency was varied from 20kHz to 200kHz. It was shown that the PM-FBG sensor system was able to detect high-speed ultrasound waves and capture the characteristics under different actuation conditions. Both longitudinal and lateral strain components in the order of nano-strain were determined based on the reflective intensity measurement data from fast and slow axis of the PM fiber. It must be emphasized that this is the first attempt to investigate acouto-ultrasonic sensing using PM-FBG sensor. This could lead to a new sensing approach in the SHM applications. Nomenclature.

Influence of crack opening and incident wave angle on second harmonic generation of Lamb waves

NASA Astrophysics Data System (ADS)

Yang, Yi; Ng, Ching-Tai; Kotousov, Andrei

2018-05-01

Techniques utilising second harmonic generation (SHG) have proven their great potential in detecting contact-type damage. However, the gap between the practical applications and laboratory studies is still quite large. The current work is aimed to bridge this gap by investigating the effects of the applied load and incident wave angle on the detectability of fatigue cracks at various lengths. Both effects are critical for practical implementations of these techniques. The present experimental study supported by three-dimensional (3D) finite element (FE) modelling has demonstrated that the applied load, which changes the crack opening and, subsequently, the contact nonlinearity, significantly affects the amplitude of the second harmonic generated by the fundamental symmetric mode (S0) of Lamb wave. This amplitude is also dependent on the length of the fatigue crack as well as the incident wave angle. The experimental and FE results correlate well, so the modelling approach can be implemented for practical design of damage monitoring systems as well as for the evaluation of the severity of the fatigue cracks.

Gradient-index phononic crystal lens-based enhancement of elastic wave energy harvesting

NASA Astrophysics Data System (ADS)

Tol, S.; Degertekin, F. L.; Erturk, A.

2016-08-01

We explore the enhancement of structure-borne elastic wave energy harvesting, both numerically and experimentally, by exploiting a Gradient-Index Phononic Crystal Lens (GRIN-PCL) structure. The proposed GRIN-PCL is formed by an array of blind holes with different diameters on an aluminum plate, where the blind hole distribution is tailored to obtain a hyperbolic secant gradient profile of refractive index guided by finite-element simulations of the lowest asymmetric mode Lamb wave band diagrams. Under plane wave excitation from a line source, experimentally measured wave field validates the numerical simulation of wave focusing within the GRIN-PCL domain. A piezoelectric energy harvester disk located at the first focus of the GRIN-PCL yields an order of magnitude larger power output as compared to the baseline case of energy harvesting without the GRIN-PCL on the uniform plate counterpart.

Methods of localization of Lamb wave sources on thin plates

NASA Astrophysics Data System (ADS)

Turkaya, Semih; Toussaint, Renaud; Kvalheim Eriksen, Fredrik; Daniel, Guillaume; Grude Flekkøy, Eirik; Jørgen Måløy, Knut

2015-04-01

Signal localization techniques are ubiquitous in both industry and academic communities. We propose a new localization method on plates which is based on energy amplitude attenuation and inverted source amplitude comparison. This inversion is tested on synthetic data using Lamb wave propagation direct model and on experimental dataset (recorded with 4 Brüel & Kjær Type 4374 miniature piezoelectric shock accelerometers (1-26 kHz frequency range)). We compare the performance of the technique to the classical source localization algorithms, arrival time localization, time reversal localization, localization based on energy amplitude. Furthermore, we measure and compare the accuracy of these techniques as function of sampling rate, dynamic range, geometry, Signal to Noise Ratio, and we show that this very versatile technique works better than classical ones over the sampling rates 100kHz - 1MHz. Experimental phase consists of a glass plate having dimensions of 80cmx40cm with a thickness of 1cm. Generated signals due to a wooden hammer hit or a steel ball hit are captured by sensors placed on the plate on different locations with the mentioned sensors. Numerical simulations are done using dispersive far field approximation of plate waves. Signals are generated using a hertzian loading over the plate. Using imaginary sources outside the plate boundaries the effect of reflections is also included. This proposed method, can be modified to be implemented on 3d environments, monitor industrial activities (e.g boreholes drilling/production activities) or natural brittle systems (e.g earthquakes, volcanoes, avalanches).

On-Line Corrosion Monitoring of Plate Structures Based on Guided Wave Tomography Using Piezoelectric Sensors.

PubMed

Rao, Jing; Ratassepp, Madis; Lisevych, Danylo; Hamzah Caffoor, Mahadhir; Fan, Zheng

2017-12-12

Corrosion is a major safety and economic concern to various industries. In this paper, a novel ultrasonic guided wave tomography (GWT) system based on self-designed piezoelectric sensors is presented for on-line corrosion monitoring of large plate-like structures. Accurate thickness reconstruction of corrosion damages is achieved by using the dispersive regimes of selected guided waves and a reconstruction algorithm based on full waveform inversion (FWI). The system makes use of an array of miniaturised piezoelectric transducers that are capable of exciting and receiving highly dispersive A0 Lamb wave mode at low frequencies. The scattering from transducer array has been found to have a small effect on the thickness reconstruction. The efficiency and the accuracy of the new system have been demonstrated through continuous forced corrosion experiments. The FWI reconstructed thicknesses show good agreement with analytical predictions obtained by Faraday's law and laser measurements, and more importantly, the thickness images closely resemble the actual corrosion sites.

Add-on unidirectional elastic metamaterial plate cloak

PubMed Central

Lee, Min Kyung; Kim, Yoon Young

2016-01-01

Metamaterial cloaks control the propagation of waves to make an object invisible or insensible. To manipulate elastic waves in space, a metamaterial cloak is typically embedded in a base system that includes or surrounds a target object. The embedding is undesirable because it structurally weakens or permanently alters the base system. In this study, we propose a new add-on metamaterial elastic cloak that can be placed over and mechanically coupled with a base structure without embedding. We designed an add-on type annular metamaterial plate cloak through conformal mapping, fabricated it and performed cloaking experiments in a thin-plate with a hole. Experiments were performed in a thin plate by using the lowest symmetric Lamb wave centered at 100 kHz. As a means to check the cloaking performance of the add-on elastic plate cloak, possibly as a temporary stress reliever or a so-called “stress bandage”, the degree of stress concentration mitigation and the recovery from the perturbed wave field due to a hole were investigated. PMID:26860896

Add-on unidirectional elastic metamaterial plate cloak

NASA Astrophysics Data System (ADS)

Lee, Min Kyung; Kim, Yoon Young

2016-02-01

Metamaterial cloaks control the propagation of waves to make an object invisible or insensible. To manipulate elastic waves in space, a metamaterial cloak is typically embedded in a base system that includes or surrounds a target object. The embedding is undesirable because it structurally weakens or permanently alters the base system. In this study, we propose a new add-on metamaterial elastic cloak that can be placed over and mechanically coupled with a base structure without embedding. We designed an add-on type annular metamaterial plate cloak through conformal mapping, fabricated it and performed cloaking experiments in a thin-plate with a hole. Experiments were performed in a thin plate by using the lowest symmetric Lamb wave centered at 100 kHz. As a means to check the cloaking performance of the add-on elastic plate cloak, possibly as a temporary stress reliever or a so-called “stress bandage”, the degree of stress concentration mitigation and the recovery from the perturbed wave field due to a hole were investigated.

Wave Response during Hydrostatic and Geostrophic Adjustment. Part I: Transient Dynamics.

NASA Astrophysics Data System (ADS)

Chagnon, Jeffrey M.; Bannon, Peter R.

2005-05-01

The adjustment of a compressible, stably stratified atmosphere to sources of hydrostatic and geostrophic imbalance is investigated using a linear model. Imbalance is produced by prescribed, time-dependent injections of mass, heat, or momentum that model those processes considered “external” to the scales of motion on which the linearization and other model assumptions are justifiable. Solutions are demonstrated in response to a localized warming characteristic of small isolated clouds, larger thunderstorms, and convective systems.For a semi-infinite atmosphere, solutions consist of a set of vertical modes of continuously varying wavenumber, each of which contains time dependencies classified as steady, acoustic wave, and buoyancy wave contributions. Additionally, a rigid lower-boundary condition implies the existence of a discrete mode—the Lamb mode— containing only a steady and acoustic wave contribution. The forced solutions are generalized in terms of a temporal Green's function, which represents the response to an instantaneous injection.The response to an instantaneous warming with geometry representative of a small, isolated cloud takes place in two stages. Within the first few minutes, acoustic and Lamb waves accomplish an expansion of the heated region. Within the first quarter-hour, nonhydrostatic buoyancy waves accomplish an upward displacement inside of the heated region with inflow below, outflow above, and weak subsidence on the periphery—all mainly accomplished by the lowest vertical wavenumber modes, which have the largest horizontal group speed. More complicated transient patterns of inflow aloft and outflow along the lower boundary are accomplished by higher vertical wavenumber modes. Among these is an outwardly propagating rotor along the lower boundary that effectively displaces the low-level inflow upward and outward.A warming of 20 min duration with geometry representative of a large thunderstorm generates only a weak acoustic response in the horizontal by the Lamb waves. The amplitude of this signal increases during the onset of the heating and decreases as the heating is turned off. The lowest vertical wavenumber buoyancy waves still dominate the horizontal adjustment, and the horizontal scale of displacements is increased by an order of magnitude. Within a few hours the transient motions remove the perturbations and an approximately trivial balanced state is established.A warming of 2 h duration with geometry representative of a large convective system generates a weak but discernible Lamb wave signal. The response to the conglomerate system is mainly hydrostatic. After several hours, the only signal in the vicinity of the heated region is that of inertia-gravity waves oscillating about a nontrivial hydrostatic and geostrophic state.This paper is the first of two parts treating the transient dynamics of hydrostatic and geostrophic adjustment. Part II examines the potential vorticity conservation and the partitioning of total energy.

Damage Detection Using Lamb Waves for Structural Health Monitoring

DTIC Science & Technology

2007-03-01

experiments have been reported by Seth Kessler [8]. 2.2 Large Aluminum Plate The second experiment included a 2024-0 aluminum plate with dimensions of...Mechanical Engineering Congress , (IMECE2002- 39017) (17-22 November 2002). 6. Kessler , Seth S. Piezoelectric-Based In-Situ Damage Detection of...Composite Materials for Structural Health Monitoring Systems. Ph.D. thesis, Massachusetts Institute of Technology, January 2002. 7. Kessler , Seth S. “Metis

Electromagnetomechanical elastodynamic model for Lamb wave damage quantification in composites

NASA Astrophysics Data System (ADS)

Borkowski, Luke; Chattopadhyay, Aditi

2014-03-01

Physics-based wave propagation computational models play a key role in structural health monitoring (SHM) and the development of improved damage quantification methodologies. Guided waves (GWs), such as Lamb waves, provide the capability to monitor large plate-like aerospace structures with limited actuators and sensors and are sensitive to small scale damage; however due to the complex nature of GWs, accurate and efficient computation tools are necessary to investigate the mechanisms responsible for dispersion, coupling, and interaction with damage. In this paper, the local interaction simulation approach (LISA) coupled with the sharp interface model (SIM) solution methodology is used to solve the fully coupled electro-magneto-mechanical elastodynamic equations for the piezoelectric and piezomagnetic actuation and sensing of GWs in fiber reinforced composite material systems. The final framework provides the full three-dimensional displacement as well as electrical and magnetic potential fields for arbitrary plate and transducer geometries and excitation waveform and frequency. The model is validated experimentally and proven computationally efficient for a laminated composite plate. Studies are performed with surface bonded piezoelectric and embedded piezomagnetic sensors to gain insight into the physics of experimental techniques used for SHM. The symmetric collocation of piezoelectric actuators is modeled to demonstrate mode suppression in laminated composites for the purpose of damage detection. The effect of delamination and damage (i.e., matrix cracking) on the GW propagation is demonstrated and quantified. The developed model provides a valuable tool for the improvement of SHM techniques due to its proven accuracy and computational efficiency.

Effects of using ground redberry juniper and dried distillers grains with solubles in lamb feedlot diets: growth, blood serum, fecal, and wool characteristics.

PubMed

Whitney, T R; Lupton, C J; Muir, J P; Adams, R P; Stewart, W C

2014-03-01

Effects of using ground redberry juniper and dried distillers grains with solubles (DDGS) in Rambouillet lamb (n = 45) feedlot diets on growth, blood serum, fecal, and wool characteristics were evaluated. In a randomized design study with 2 feeding periods (Period 1 = 64% concentrate diet, 35 d; Period 2 = 85% concentrate diet, 56 d), lambs were individually fed 5 isonitrogenous diets: a control diet (CNTL) that contained oat hay but not DDGS or juniper or DDGS-based diets in which 0 (0JUN), 33 (33JUN), 66 (66JUN), or 100% (100JUN) of the oat hay was replaced by juniper. During Period 1, lambs fed CNTL had greater (P < 0.05) DMI and ADG and tended to have greater (P < 0.10) G:F than lambs fed 0JUN or lambs fed DDGS-based diets. Lamb DMI, ADG, and G:F quadratically increased (P < 0.008) as juniper increased in the DDGS-based diets. During Period 2, lambs fed CNTL had greater (P < 0.05) DMI than lambs fed 0JUN or lambs fed DDGS-based diets, but ADG was similar (P > 0.41). Compared to 0JUN, lambs fed CNTL had similar (P = 0.12) G:F and tended to have less G:F (P = 0.07) than lambs fed DDGS-based diets. Among lambs fed DDGS-based diets, DMI was similar (P > 0.19), ADG increased linearly (P = 0.03), and G:F tended to decrease quadratically (P = 0.06) as juniper increased in the diet. Serum IGF-1, serum urea N (SUN), and fecal N were greater (P < 0.05) and serum Ca and P and fecal P were similar (P > 0.13) for lambs fed CNTL vs. lambs fed DDGS-based diets (CNTL). Within lambs fed DDGS-based diets, SUN increased quadratically (P = 0.01) and fecal N increased linearly (P = 0.004), which can partially be attributed to increased dietary urea and condensed tannin intake. Most wool characteristics were not affected, but wool growth per kilogram of BW decreased quadratically (P = 0.04) as percentage of juniper increased in the DDGS-based diets. When evaluating the entire 91-d feeding trial, results indicated that replacing all of the ground oat hay with ground juniper leaves and stems in lamb growing and finishing diets is not detrimental to animal performance and that DDGS-based diets can reduce total feedlot costs, as compared to sorghum grain and cottonseed meal-based diets. However, compared to using juniper or oat hay as the sole roughage source, using both during the growing period (Period 1) enhanced growth performance and further reduced total feedlot costs.

The quasi-harmonic ultrasonic polar scan for material characterization: experiment and numerical modeling.

PubMed

Kersemans, Mathias; Martens, Arvid; Van Den Abeele, Koen; Degrieck, Joris; Pyl, Lincy; Zastavnik, Filip; Sol, Hugo; Van Paepegem, Wim

2015-04-01

Conventionally, the ultrasonic polar scan (UPS) records the amplitude or time-of-flight in transmission using short ultrasonic pulses for a wide range of incidence angles, resulting in a fingerprint of the critical bulk wave angles of the material at the insonified spot. Here, we investigate the use of quasi-harmonic ultrasound (bursts) in a polar scan experiment, both experimentally and numerically. It is shown that the nature of the fingerprint drastically changes, and reveals the positions of the leaky Lamb angles. To compare with experiments, both plane wave and bounded beam simulations have been performed based on the recursive stiffness matrix method. Whereas the plane wave computations yield a pure Lamb wave angle fingerprint, this is no longer valid for the more realistic case of a bounded beam. The experimental recordings are fully supported by the bounded beam simulations. To complement the traditional amplitude measurement, experimental and numerical investigations have been performed to record, predict and analyze the phase of the transmitted ultrasonic beam. This results in the conceptual introduction of the 'phase polar scan', exposing even more intriguing and detailed patterns. In fact, the combination of the amplitude and the phase polar scan provides the complete knowledge about the complex transmission coefficient for every possible angle of incidence. This comprehensive information will be very valuable for inverse modeling of the local elasticity tensor based on a single UPS experiment. Finally, the UPS method has been applied for the detection of an artificial delamination. Compared to the pulsed UPS, the quasi-harmonic UPS (both the amplitude and phase recording) shows a superior sensitivity to the presence of a delamination. Copyright © 2015 Elsevier B.V. All rights reserved.

Mode separation in frequency-wavenumber domain through compressed sensing of far-field Lamb waves

NASA Astrophysics Data System (ADS)

Gao, Fei; Zeng, Liang; Lin, Jing; Luo, Zhi

2017-07-01

This method based on Lamb waves shows great potential for long-range damage detection. Mode superposition resulting from multi-modal and dispersive characteristics makes signal interpretation and damage feature extraction difficult. Mode separation in the frequency-wavenumber (f-k) domain using a 1D sparse sensing array is a promising solution. However, due to the lack of prior knowledge about damage location, this method based on 1D linear measurement, for the mode extraction of arbitrary reflections caused by defects that are not in line with the sensor array, is restricted. In this paper, an improved compressed sensing method under the far-field assumption is established, which is beneficial to the reconstruction of reflections in the f-k domain. Hence, multiple components consisting of structure and damage features could be recovered via a limited number of measurements. Subsequently, a mode sweeping process based on theoretical dispersion curves has been designed for mode characterization and direction of arrival estimation. Moreover, 2D f-k filtering and inverse transforms are applied to the reconstructed f-k distribution in order to extract the purified mode of interest. As a result, overlapping waveforms can be separated and the direction of defects can be estimated. A uniform linear sensor array consisting of 16 laser excitations is finally employed for experimental investigations and the results demonstrate the efficiency of the proposed method.

Optimizing a spectral element for modeling PZT-induced Lamb wave propagation in thin plates

NASA Astrophysics Data System (ADS)

Ha, Sungwon; Chang, Fu-Kuo

2010-01-01

Use of surface-mounted piezoelectric actuators to generate acoustic ultrasound has been demonstrated to be a key component of built-in nondestructive detection evaluation (NDE) techniques, which can automatically inspect and interrogate damage in hard-to-access areas in real time without disassembly of the structural parts. However, piezoelectric actuators create complex waves, which propagate through the structure. Having the capability to model piezoelectric actuator-induced wave propagation and understanding its physics are essential to developing advanced algorithms for the built-in NDE techniques. Therefore, the objective of this investigation was to develop an efficient hybrid spectral element for modeling piezoelectric actuator-induced high-frequency wave propagation in thin plates. With the hybrid element we take advantage of both a high-order spectral element in the in-plane direction and a linear finite element in the thickness direction in order to efficiently analyze Lamb wave propagation in thin plates. The hybrid spectral element out-performs other elements in terms of leading to significantly faster computation and smaller memory requirements. Use of the hybrid spectral element is proven to be an efficient technique for modeling PZT-induced (PZT: lead zirconate titanate) wave propagation in thin plates. The element enables fundamental understanding of PZT-induced wave propagation.

3D Modeling of Ultrasonic Wave Interaction with Disbonds and Weak Bonds

NASA Technical Reports Server (NTRS)

Leckey, C.; Hinders, M.

2011-01-01

Ultrasonic techniques, such as the use of guided waves, can be ideal for finding damage in the plate and pipe-like structures used in aerospace applications. However, the interaction of waves with real flaw types and geometries can lead to experimental signals that are difficult to interpret. 3-dimensional (3D) elastic wave simulations can be a powerful tool in understanding the complicated wave scattering involved in flaw detection and for optimizing experimental techniques. We have developed and implemented parallel 3D elastodynamic finite integration technique (3D EFIT) code to investigate Lamb wave scattering from realistic flaws. This paper discusses simulation results for an aluminum-aluminum diffusion disbond and an aluminum-epoxy disbond and compares results from the disbond case to the common artificial flaw type of a flat-bottom hole. The paper also discusses the potential for extending the 3D EFIT equations to incorporate physics-based weak bond models for simulating wave scattering from weak adhesive bonds.

Wave propagation modeling in composites reinforced by randomly oriented fibers

NASA Astrophysics Data System (ADS)

Kudela, Pawel; Radzienski, Maciej; Ostachowicz, Wieslaw

2018-02-01

A new method for prediction of elastic constants in randomly oriented fiber composites is proposed. It is based on mechanics of composites, the rule of mixtures and total mass balance tailored to the spectral element mesh composed of 3D brick elements. Selected elastic properties predicted by the proposed method are compared with values obtained by another theoretical method. The proposed method is applied for simulation of Lamb waves in glass-epoxy composite plate reinforced by randomly oriented fibers. Full wavefield measurements conducted by the scanning laser Doppler vibrometer are in good agreement with simulations performed by using the time domain spectral element method.

Understanding of Materials State and its Degradation using Non-Linear Ultrasound Approaches for Lamb Wave Propagation

DTIC Science & Technology

2015-05-31

Institution : Indian Institute of Technology Madras - Mailing Address : MDS 301, Department of Mechanical Engineering, IIT Campus, Chennia INDIA 600036...in ceramic composites using an ultrasonic guided wave scan system”, 30th Annual Rev. of Quan. NDE, 2003; NASA /TM-2003-212518. [15] J Y Kim, J Qu

Lamb mode selection for accurate wall loss estimation via guided wave tomography

NASA Astrophysics Data System (ADS)

Huthwaite, P.; Ribichini, R.; Lowe, M. J. S.; Cawley, P.

2014-02-01

Guided wave tomography offers a method to accurately quantify wall thickness losses in pipes and vessels caused by corrosion. This is achieved using ultrasonic waves transmitted over distances of approximately 1-2m, which are measured by an array of transducers and then used to reconstruct a map of wall thickness throughout the inspected region. To achieve accurate estimations of remnant wall thickness, it is vital that a suitable Lamb mode is chosen. This paper presents a detailed evaluation of the fundamental modes, S0 and A0, which are of primary interest in guided wave tomography thickness estimates since the higher order modes do not exist at all thicknesses, to compare their performance using both numerical and experimental data while considering a range of challenging phenomena. The sensitivity of A0 to thickness variations was shown to be superior to S0, however, the attenuation from A0 when a liquid loading was present was much higher than S0. A0 was less sensitive to the presence of coatings on the surface of than S0.

Wireless power transmission using ultrasonic guided waves

NASA Astrophysics Data System (ADS)

Kural, A.; Pullin, R.; Featherston, C.; Paget, C.; Holford, K.

2011-07-01

The unavailability of suitable power supply at desired locations is currently an important obstacle in the development of distributed, wireless sensor networks for applications such as structural health monitoring of aircraft. Proposed solutions range from improved batteries to energy harvesting from vibration, temperature gradients and other sources. A novel approach is being investigated at Cardiff University School of Engineering in cooperation with Airbus. It aims to utilise ultrasonic guided Lamb waves to transmit energy through the aircraft skin. A vibration generator is to be placed in a location where electricity supply is readily available. Ultrasonic waves generated by this device will travel through the aircraft structure to a receiver in a remote wireless sensor node. The receiver will convert the mechanical vibration of the ultrasonic waves back to electricity, which will be used to power the sensor node. This paper describes the measurement and modelling of the interference pattern which emerges when Lamb waves are transmitted continuously as in this power transmission application. The discovered features of the pattern, such as a large signal amplitude variation and a relatively high frequency, are presented and their importance for the development of a power transmission system is discussed.

Broadband attenuation of Lamb waves through a periodic array of thin rectangular junctions

NASA Astrophysics Data System (ADS)

Moiseyenko, Rayisa P.; Pennec, Yan; Marchal, Rémi; Bonello, Bernard; Djafari-Rouhani, Bahram

2014-10-01

We study theoretically subwavelength physical phenomena, such as resonant transmission and broadband sound shielding for Lamb waves propagating in an acoustic metamaterial made of a thin plate drilled with one or two row(s) of rectangular holes. The resonances and antiresonances of periodically arranged rectangular junctions separated by holes are investigated as a function of the geometrical parameters of the junctions. With one and two row(s) of holes, high frequency specific features in the transmission coefficient are explained in terms of a coupling of incident waves with both Fabry-Perot oscillations inside the junctions and induced surface acoustic waves between the homogeneous part of the plate and the row of holes. With two rows of holes, low frequency peaks and dips appear in the transmission spectrum. The choice of the distance between the two rows of holes allows the realization of a broadband low frequency acoustic shielding with attenuation over 99% for symmetric waves in a wide low frequency range and over 90% for antisymmetric ones. The origin of the transmission gap is discussed in terms of localized modes of the "H" element made by the junctions, connecting the two homogeneous parts of the plate.

Analysis of Critically Refracted Longitudinal and Lamb Waves for Stress Characterization

NASA Astrophysics Data System (ADS)

Pei, Ning

The global production of metal, in particular, steel and aluminum keeps increasing. This material is used with various fabrication processes, such as, welding, forging, and rolling that can induce stresses in the material that can subsequently impact product performance and cause phenomena such as cracking and corrosion. When investigating plate materials it is necessary to map both texture and stress under a range of loading conditions. To address these needs a wide range of both destructive and nondestructive tools have been used. One family of methods are those based on ultrasonic measurements that relate ultrasonic velocity to properties, in particular stress. Two particular challenges are faced which are the relative insensitivity of compression and shear waves to stress and that there are also other factors which can also change velocity and these are temperature, texture and grain size. This project focused on an analysis of ultrasonic velocity measurements and specifically ways to improve performance and capabilities for stress characterization. Two approaches were considered and are reported: the critically refracted ultrasonic longitudinal (LCR) wave and higher order Lamb waves. The LCR wave method was modelled and optimized based on the fact that the sensitivity between waves and stress can reach maximum when they propagate in the same direction. However, in reality this wave typically propagates at an angle to stress, which will decrease its sensitivity. This thesis reports a numerical model used to investigate the transducers parameters that can influence the directivity of the LCR wave and hence enable performance optimization when used for industrial applications. An orthogonal test method is used to study the transducer parameters which influence the LCR wave beams and this method provides a design tool that can be used to study and optimize multiple parameter experiments and identify which parameter or parameters are of most significance. The example considered simulation of the acoustic field in a 2-D water-steel model is obtained using a Spatial Fourier Analysis method. The significance of the effects of incident angle, the aperture and the center frequency of the transducer were studied. Results show that the aperture, the center frequency and the incident angle are the most important factors in controlling the directivity of the resulting LCR wave fields.

Lamb Wave Multitouch Ultrasonic Touchscreen.

PubMed

Firouzi, Kamyar; Nikoozadeh, Amin; Carver, Thomas E; Khuri-Yakub, Butrus Pierre T

2016-12-01

Touchscreen sensors are widely used in many devices such as smart phones, tablets, and laptops with diverse applications. We present the design, analysis, and implementation of an ultrasonic touchscreen system that utilizes the interaction of transient Lamb waves with objects in contact with the screen. It attempts to improve on the existing ultrasound technologies, with the potential of addressing some of the weaknesses of the dominant technologies, such as the capacitive or resistive ones. Compared with the existing ultrasonic and acoustic modalities, among other advantages, it provides the capability of detecting several simultaneous touch points and also a more robust performance. The localization algorithm, given the hardware design, can detect several touch points with a very limited number of measurements (one or two). This in turn can significantly reduce the manufacturing cost.

Material and Phonon Engineering for Next Generation Acoustic Devices

NASA Astrophysics Data System (ADS)

Kuo, Nai-Kuei

This thesis presents the theoretical and experimental work related to micromachining of low intrinsic loss sapphire and phononic crystals for engineering new classes of electroacoustic devices for frequency control applications. For the first time, a low loss sapphire suspended membrane was fabricated and utilized to form the main body of a piezoelectric lateral overtone bulk acoustic resonator (LOBAR). Since the metalized piezoelectric transducer area in a LOBAR is only a small fraction of the overall resonant cavity (made out of sapphire), high quality factor (Q) overtones are attained. The experiment confirms the low intrinsic mechanical loss of the transferred sapphire thin film, and the resonators exhibit the highest Q of 5,440 at 2.8 GHz ( f·Q of 1.53.1013 Hz). This is also the highest f·Q demonstrated for aluminum-nitride-(AIN)-based Lamb wave devices to date. Beyond demonstrating a low loss device, this experimental work has laid the foundation for the future development of new micromechanical devices based on a high Q, high hardness and chemically resilient material. The search for alternative ways to more efficiently perform frequency control functionalities lead to the exploration of Phononic Crystal (PnC) structures in AIN thin films. Four unit cell designs were theoretically and experimentally investigated to explore the behavior of phononic bandgaps (PBGs) in the ultra high frequency (UHF) range: (i) the conventional square lattice with circular air scatterer, (ii) the inverse acoustic bandgap (IABG) structure, (iii) the fractal PnC, and (iv) the X-shaped PnC. Each unit cell has its unique frequency characteristic that was exploited to synthesize either cavity resonators or improve the performance of acoustic delay lines. The PBGs operate in the range of 770 MHz to 1 GHz and exhibit a maximum acoustic rejection of 40 dB. AIN Lamb wave transducers (LWTs) were employed for the experimental demonstration of the PBGs and cavity resonances. Ultra-wide bandwidth (˜10%) was achieved by implementing slanted finger transducers (SFIT) in thin film AIN. The impulse response and coupling of modes (COM) models commonly used for surface acoustic wave (SAW) devices were developed to design the operating frequency and bandwidth of the LWTs. These techniques enabled access to fast frequency solutions (impulse response method) and good pass-band ripple estimation (COM) for any piezoelectric Lamb-wave based device. The conventional and IABG unit cell designs were explored for the making of cavity resonators. A PnC cavity made with conventional design exhibits a Q of 675 at 665 MHz. Despite the low Q, its value is very high when the volume of the cavity is taken into account ( Q per unit volume of 3.1017/m3). In order to understand the limited value of Q a detailed finite element analysis is performed to unveil its dependence on the specific design of the transducer. The capabilities of the X-shaped PnCs were harvested for synthesizing a method to suppress the sidelobe response of an AIN Lamb wave (SFIT) delay line. 10 dB of sidelobe magnitude reduction was attained while leaving the pass-band unaltered. Although at a very preliminary stage, the theoretical and experimental work on AIN PnC has demonstrated that new acoustic capabilities are enabled by these metamaterials. Future electroacoustic devices that perform frequency control functions in a compact and low loss fashion can now be envisioned.

Statistical lamb wave localization based on extreme value theory

NASA Astrophysics Data System (ADS)

Harley, Joel B.

2018-04-01

Guided wave localization methods based on delay-and-sum imaging, matched field processing, and other techniques have been designed and researched to create images that locate and describe structural damage. The maximum value of these images typically represent an estimated damage location. Yet, it is often unclear if this maximum value, or any other value in the image, is a statistically significant indicator of damage. Furthermore, there are currently few, if any, approaches to assess the statistical significance of guided wave localization images. As a result, we present statistical delay-and-sum and statistical matched field processing localization methods to create statistically significant images of damage. Our framework uses constant rate of false alarm statistics and extreme value theory to detect damage with little prior information. We demonstrate our methods with in situ guided wave data from an aluminum plate to detect two 0.75 cm diameter holes. Our results show an expected improvement in statistical significance as the number of sensors increase. With seventeen sensors, both methods successfully detect damage with statistical significance.

In Situ Estimation of Applied Biaxial Loads with Lamb Waves (Preprint)

DTIC Science & Technology

2012-07-01

be correct. IV. EXPERIMENTS AND RESULTS Fatigue tests were conducted for an array of six surface-bonded PZT transducers permanently attached to...because of their cumulative effects on the fatigue life of the structures. Waves propagating between array elements are directly affected by applied loads...their cumulative effects on the fatigue life of the structures. Waves propagating between array elements are directly affected by applied loads

Composite Materials NDE Using Enhanced Leaky Lamb Wave Dispersion Data Acquisition Method

NASA Technical Reports Server (NTRS)

Bar-Cohen, Yoseph; Mal, Ajit; Lih, Shyh-Shiuh; Chang, Zensheu

1999-01-01

The leaky Lamb wave (LLW) technique is approaching a maturity level that is making it an attractive quantitative NDE tool for composites and bonded joints. Since it was first observed in 1982, the phenomenon has been studied extensively, particularly in composite materials. The wave is induced by oblique insonification using a pitch-catch arrangement and the plate wave modes are detected by identifying minima in the reflected spectra to obtain the dispersion data. The wave behavior in multi-orientation laminates has been well documented and corroborated experimentally with high accuracy. The sensitivity of the wave to the elastic constants of the material and to the boundary conditions led to the capability to measure the elastic properties of bonded joints. Recently, the authors significantly enhanced the LLW method's capability by increasing the speed of the data acquisition, the number of modes that can be identified and the accuracy of the data inversion. In spite of the theoretical and experimental progress, methods that employ oblique insonification of composites are still not being applied as standard industrial NDE methods. The authors investigated the issues that are hampering the transition of the LLW to industrial applications and identified 4 key issues. The current capability of the method and the nature of these issues are described in this paper.

Real-Time Leaky Lamb Wave Spectrum Measurement and Its Application to NDE of Composites

NASA Technical Reports Server (NTRS)

Lih, Shyh-Shiuh; Bar-Cohen, Yoseph

1999-01-01

Numerous analytical and theoretical studies of the behavior of leaky Lamb waves (LLW) in composite materials were documented in the literature. One of the key issues that are constraining the application of this method as a practical tool is the amount of data that needs to be acquired and the slow process that is involved with such experiments. Recently, a methodology that allows quasi real-time acquisition of LLW dispersion data was developed. At each angle of incidence the reflection spectrum is available in real time from the experimental setup and it can be used for rapid detection of the defects. This technique can be used to rapidly acquire the various plate wave modes along various angles of incidence for the characterization of the material elastic properties. The experimental method and data acquisition technique will be described in this paper. Experimental data was used to examine a series of flaws including porosity and delaminations and demonstrated the efficiency of the developed technique.

On-Line Monitoring and Diagnostics of the Integrity of Nuclear Plant Steam Generators and Heat Exchangers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belle R. Upadhyaya; J. Wesley Hines

2004-09-27

Integrity monitoring and flaw diagnostics of flat beams and tubular structures was investigated in this research task using guided acoustic signals. A piezo-sensor suite was deployed to activate and collect Lamb wave signals that propagate along metallic specimens. The dispersion curves of Lamb waves along plate and tubular structures are generated through numerical analysis. Several advanced techniques were explored to extract representative features from acoustic time series. Among them, the Hilbert-Huang transform (HHT) is a recently developed technique for the analysis of non-linear and transient signals. A moving window method was introduced to generate the local peak characters from acousticmore » time series, and a zooming window technique was developed to localize the structural flaws. The time-frequency analysis and pattern recognition techniques were combined for classifying structural defects in brass tubes. Several types of flaws in brass tubes were tested, both in the air and in water. The techniques also proved to be effective under background/process noise. A detailed theoretical analysis of Lamb wave propagation was performed and simulations were carried out using the finite element software system ABAQUS. This analytical study confirmed the behavior of the acoustic signals acquired from the experimental studies. The report presents the background the analysis of acoustic signals acquired from piezo-electric transducers for structural defect monitoring. A comparison of the use of time-frequency techniques, including the Hilbert-Huang transform, is presented. The report presents the theoretical study of Lamb wave propagation in flat beams and tubular structures, and the need for mode separation in order to effectively perform defect diagnosis. The results of an extensive experimental study of detection, location, and isolation of structural defects in flat aluminum beams and brass tubes are presented. The results of this research show the feasibility of on-line monitoring of small structural flaws by the use of transient and nonlinear acoustic signal analysis, and its implementation by the proper design of a piezo-electric transducer suite.« less

Quantitative assessment of corneal viscoelasticity using optical coherence elastography and a modified Rayleigh-Lamb equation

NASA Astrophysics Data System (ADS)

Han, Zhaolong; Aglyamov, Salavat R.; Li, Jiasong; Singh, Manmohan; Wang, Shang; Vantipalli, Srilatha; Wu, Chen; Liu, Chih-hao; Twa, Michael D.; Larin, Kirill V.

2015-02-01

We demonstrate the use of a modified Rayleigh-Lamb frequency equation in conjunction with noncontact optical coherence elastography to quantify the viscoelastic properties of the cornea. Phase velocities of air-pulse-induced elastic waves were extracted by spectral analysis and used for calculating the Young's moduli of the samples using the Rayleigh-Lamb frequency equation (RLFE). Validation experiments were performed on 2% agar phantoms (n=3) and then applied to porcine corneas (n=3) in situ. The Young's moduli of the porcine corneas were estimated to be ˜60 kPa with a shear viscosity ˜0.33 Pa.s. The results demonstrate that the RLFE is a promising method for noninvasive quantification of the corneal biomechanical properties and may potentially be useful for clinical ophthalmological applications.

Mode Conversion Behavior of Guided Wave in a Pipe Inspection System Based on a Long Waveguide.

PubMed

Sun, Feiran; Sun, Zhenguo; Chen, Qiang; Murayama, Riichi; Nishino, Hideo

2016-10-19

To make clear the mode conversion behavior of S0-mode lamb wave and SH0-plate wave converting to the longitudinal mode guided wave and torsional mode guided wave in a pipe, respectively, the experiments were performed based on a previous built pipe inspection system. The pipe was wound with an L-shaped plate or a T-shaped plate as the waveguide, and the S0-wave and SH0-wave were excited separately in the waveguide. To carry out the objective, a meander-line coil electromagnetic acoustic transducer (EMAT) for S0-wave and a periodic permanent magnet (PPM) EMAT for SH0-wave were developed and optimized. Then, several comparison experiments were conducted to compare the efficiency of mode conversion. Experimental results showed that the T(0,1) mode, L(0,1) mode, and L(0,2) mode guided waves can be successfully detected when converted from the S0-wave or SH0-wave with different shaped waveguides. It can also be inferred that the S0-wave has a better ability to convert to the T(0,1) mode, while the SH0-wave is easier to convert to the L(0,1) mode and L(0,2) mode, and the L-shaped waveguide has a better efficiency than T-shaped waveguide.

An Optimal Image-Based Method for Identification of Acoustic Emission (AE) Sources in Plate-Like Structures Using a Lead Zirconium Titanate (PZT) Sensor Array.

PubMed

Yan, Gang; Zhou, Li

2018-02-21

This paper proposes an innovative method for identifying the locations of multiple simultaneous acoustic emission (AE) events in plate-like structures from the view of image processing. By using a linear lead zirconium titanate (PZT) sensor array to record the AE wave signals, a reverse-time frequency-wavenumber (f-k) migration is employed to produce images displaying the locations of AE sources by back-propagating the AE waves. Lamb wave theory is included in the f-k migration to consider the dispersive property of the AE waves. Since the exact occurrence time of the AE events is usually unknown when recording the AE wave signals, a heuristic artificial bee colony (ABC) algorithm combined with an optimal criterion using minimum Shannon entropy is used to find the image with the identified AE source locations and occurrence time that mostly approximate the actual ones. Experimental studies on an aluminum plate with AE events simulated by PZT actuators are performed to validate the applicability and effectiveness of the proposed optimal image-based AE source identification method.

An Optimal Image-Based Method for Identification of Acoustic Emission (AE) Sources in Plate-Like Structures Using a Lead Zirconium Titanate (PZT) Sensor Array

PubMed Central

Zhou, Li

2018-01-01

This paper proposes an innovative method for identifying the locations of multiple simultaneous acoustic emission (AE) events in plate-like structures from the view of image processing. By using a linear lead zirconium titanate (PZT) sensor array to record the AE wave signals, a reverse-time frequency-wavenumber (f-k) migration is employed to produce images displaying the locations of AE sources by back-propagating the AE waves. Lamb wave theory is included in the f-k migration to consider the dispersive property of the AE waves. Since the exact occurrence time of the AE events is usually unknown when recording the AE wave signals, a heuristic artificial bee colony (ABC) algorithm combined with an optimal criterion using minimum Shannon entropy is used to find the image with the identified AE source locations and occurrence time that mostly approximate the actual ones. Experimental studies on an aluminum plate with AE events simulated by PZT actuators are performed to validate the applicability and effectiveness of the proposed optimal image-based AE source identification method. PMID:29466310

A Systems Engineering Process for an Integrated Structural Health Monitoring System

DTIC Science & Technology

2007-03-01

York NY, 1999. 2nd ed. 3. Chambers, Jeffrey T., Brian L. Wardle, and Seth S. Kessler . “Durability Assessment of Lamb Wave-Based Structural Health...Institute of Technology, 1960. 222 Bibliography 10. Kessler , Seth S., S. Mark Spearing, Mauro J. Atalla, Carlos E. S. Cesnik, and Constantinos...Materials, March 4-8 2001, Newport Beach, CA. Available at http://web.mit.edu/sskess/www/papers/SPIE01.pdf. 11. Kessler , Seth S., S. Mark Spearing

Dispersion curve estimation via a spatial covariance method with ultrasonic wavefield imaging.

PubMed

Chong, See Yenn; Todd, Michael D

2018-05-01

Numerous Lamb wave dispersion curve estimation methods have been developed to support damage detection and localization strategies in non-destructive evaluation/structural health monitoring (NDE/SHM) applications. In this paper, the covariance matrix is used to extract features from an ultrasonic wavefield imaging (UWI) scan in order to estimate the phase and group velocities of S0 and A0 modes. A laser ultrasonic interrogation method based on a Q-switched laser scanning system was used to interrogate full-field ultrasonic signals in a 2-mm aluminum plate at five different frequencies. These full-field ultrasonic signals were processed in three-dimensional space-time domain. Then, the time-dependent covariance matrices of the UWI were obtained based on the vector variables in Cartesian and polar coordinate spaces for all time samples. A spatial covariance map was constructed to show spatial correlations within the full wavefield. It was observed that the variances may be used as a feature for S0 and A0 mode properties. The phase velocity and the group velocity were found using a variance map and an enveloped variance map, respectively, at five different frequencies. This facilitated the estimation of Lamb wave dispersion curves. The estimated dispersion curves of the S0 and A0 modes showed good agreement with the theoretical dispersion curves. Copyright © 2018 Elsevier B.V. All rights reserved.

[Changes in the ECG telemetry of lambs infected with Cysticercus ovis].

PubMed

Kostov, I; Georgieva, D

1985-01-01

Six lambs were experimentally infected with Cysticercus ovis. Some changes were followed up in the ECG by means of the radiotelemetric method. The infection process led to the following more important changes, such as sinus tachicardia and arhythmia, auricular fibrilation, sinoauricular block, atrial dissociation, the incidence of a pathologic Q deflection; lowering of the R deflection amplitude, and inversion of the T wave. It was found that the changes referred to persist for a longer period (in the case of infarction), and could be made use of in dispensary studies.

Use of Guided Acoustic Waves to Assess the Effects of Thermal-Mechanical Cycling on Composite Stiffness

NASA Technical Reports Server (NTRS)

Seale, Michael D.; Madaras, Eric I.

2000-01-01

The introduction of new, advanced composite materials into aviation systems requires it thorough understanding of the long-term effects of combined thermal and mechanical loading. As part of a study to evaluate the effects of thermal-mechanical cycling, it guided acoustic (Lamb) wave measurement system was used to measure the bending and out-of-plane stiffness coefficients of composite laminates undergoing thermal-mechanical loading. The system uses a pulse/receive technique that excites an antisymmetric Lamb mode and measures the time-of-flight over a wide frequency range. Given the material density and plate thickness, the bending and out-of-plane shear stiffnesses are calculated from a reconstruction of the velocity dispersion curve. A series of 16 and 32-ply composite laminates were subjected to it thermal-mechanical loading profile in load frames equipped with special environmental chambers. The composite systems studied were it graphite fiber reinforced amorphous thermoplastic polyimide and it graphite fiber reinforced bismaleimide thermoset. The samples were exposed to both high and low temperature extremes its well as high and low strain profiles. The bending and out-of-plane stiffnesses for composite sample that have undergone over 6,000 cycles of thermal-mechanical loading are reported. The Lamb wave generated elastic stiffness results have shown decreases of up to 20% at 4,936 loading cycles for the graphite/thermoplastic samples and up to 64% at 4,706 loading cycles for the graphite/thermoset samples.

Using PVDF for wavenumber-frequency analysis and excitation of guided waves

NASA Astrophysics Data System (ADS)

Ren, Baiyang; Cho, Hwanjeong; Lissenden, Cliff J.

2018-04-01

The role of transducers in nondestructive evaluation using ultrasonic guided waves cannot be overstated. Energy conversion from electrical to mechanical for actuation and then back to electrical for signal processing broadly describes transduction, but there are many other aspects of transducers that determine their effectiveness. Recently we have reported on polyvinylidene difluoride (PVDF) array sensors that enable determination of the wavenumber spectrum, which enables modal content in the received signal to be characterized. Modal content is an important damage indicator because, for example, mode conversion is a frequent consequence of wave interaction with defects. Some of the positive attributes of PVDF sensors are: broad frequency bandwidth, compliance for use on curved surfaces, limited influence on the passing wave, minimal cross-talk between elements, low profile, low mass, and inexpensive. The anisotropy of PVDF films also enables them to receive either Lamb waves or shear horizontal waves by proper alignment of the material principal coordinate axes. Placing a patterned set of electrodes on the PVDF film provides data from an array of elements. A linear array of elements is used to enable a 2D fast Fourier transform to determine the wavenumber spectrum of both Lamb waves and shear horizontal waves in an aluminum plate. Moreover, since PVDF film can sustain high voltage excitation, high power pulsers can be used to improve the signal-to-noise ratio. The capability of PVDF as a transmitter has been demonstrated with high voltage excitation.

Experimental study of the acoustoelastic Lamb wave in thin plates

NASA Astrophysics Data System (ADS)

Pei, Ning; Bond, Leonard J.

2016-02-01

Many factors can cause residual stresses in industry, like rolling, welding and coating. Residual stresses can have both benefits and shortcomings on components, so it is important to find the residual stresses out and enhance its benefits part and get rid of its harmful part. There are many methods for residual stresses detection and ultrasonic method turns out to be a good one for it is nondestructive, relative cheap and portable. The critically refracted longitudinal (LCR) wave is widely used for it is regarded most sensitive to stress and less sensitive to texture which can influence detection results. Ultrasonic methods for residual stresses detection are based on time of flight (TOF) measurement, but because the measurement should reach nanosecond to show stress change, there are many other factors that can influence TOF, like temperature, texture of the components and even the thickness of the couplant. So increasing the TOF's sensitivity to stress is very important. In this paper the relationships between velocity and frequency are studied experimentally[6] for different Lamb modes, under various stress loadings. The result shows that the sensitivity of different modes various a lot, the A1 mode is the most sensitivity, compared to S0, S1 and A0 modes; if the force is added to 100 MPa, the change stress of A1 mode can be as large to 80 m/s, which is about 10 times more sensitive than the traditional bulk wave. This makes it as a good choice for residual stress detection.

A finite difference analysis of the field present behind an acoustically impenetrable two-layer barrier.

PubMed

Hurrell, Andrew M

2008-06-01

The interaction of an incident sound wave with an acoustically impenetrable two-layer barrier is considered. Of particular interest is the presence of several acoustic wave components in the shadow region of this barrier. A finite difference model capable of simulating this geometry is validated by comparison to the analytical solution for an idealized, hard-soft barrier. A panel comprising a high air-content closed cell foam backed with an elastic (metal) back plate is then examined. The insertion loss of this panel was found to exceed the dynamic range of the measurement system and was thus acoustically impenetrable. Experimental results from such a panel are shown to contain artifacts not present in the diffraction solution, when acoustic waves are incident upon the soft surface. A finite difference analysis of this experimental configuration replicates the presence of the additional field components. Furthermore, the simulated results allow the additional components to be identified as arising from the S(0) and A(0) Lamb modes traveling in the elastic plate. These Lamb mode artifacts are not found to be present in the shadow region when the acoustic waves are incident upon the elastic surface.

Material State Awareness for Composites Part I: Precursor Damage Analysis Using Ultrasonic Guided Coda Wave Interferometry (CWI).

PubMed

Patra, Subir; Banerjee, Sourav

2017-12-16

Detection of precursor damage followed by the quantification of the degraded material properties could lead to more accurate progressive failure models for composite materials. However, such information is not readily available. In composite materials, the precursor damages-for example matrix cracking, microcracks, voids, interlaminar pre-delamination crack joining matrix cracks, fiber micro-buckling, local fiber breakage, local debonding, etc.-are insensitive to the low-frequency ultrasonic guided-wave-based online nondestructive evaluation (NDE) or Structural Health Monitoring (SHM) (~100-~500 kHz) systems. Overcoming this barrier, in this article, an online ultrasonic technique is proposed using the coda part of the guided wave signal, which is often neglected. Although the first-arrival wave packets that contain the fundamental guided Lamb wave modes are unaltered, the coda wave packets however carry significant information about the precursor events with predictable phase shifts. The Taylor-series-based modified Coda Wave Interferometry (CWI) technique is proposed to quantify the stretch parameter to compensate the phase shifts in the coda wave as a result of precursor damage in composites. The CWI analysis was performed on five woven composite-fiber-reinforced-laminate specimens, and the precursor events were identified. Next, the precursor damage states were verified using high-frequency Scanning Acoustic Microscopy (SAM) and optical microscopy imaging.

Nd:YAG Pulsed Laser based flaw imaging techniques for noncontact NDE of an aluminum plate

NASA Astrophysics Data System (ADS)

Park, Woong-Ki; Lee, Changgil; Park, Seunghee

2012-04-01

Recently, the longitudinal, shear and surface waves have been very widely used as a kind of ultrasonic wave exploration methods to identify internal defects of metallic structures. The ultrasonic wave-based non-destructive testing (NDT) is one of main non-destructive inspection techniques for a health assessment about nuclear power plant, aircraft, ships, and/or automobile manufacturing. In this study, a noncontact pulsed laser-based flaw imaging NDT technique is implemented to detect the damage of a plate-like structure and to identify the location of the damage. To achieve this goal, the Nd:YAG pulsed laser equipment is used to generate a guided wave and scans a specific area to find damage location. The Nd: YAG pulsed laser is used to generate Lamb wave and piezoelectric sensors are installed to measure structural responses. Ann aluminum plate is investigated to verify the effectiveness and the robustness of the proposed NDT approach. A notch is a target to detect, which is inflicted on the surface of an aluminum plate. The damagesensitive features are extracted by comparing the time of flight of the guided wave obtained from an acoustic emission (AE) sensor and make use of the flaw imaging techniques of the aluminum plate.

Developments in signal processing and interpretation in laser tapping

NASA Astrophysics Data System (ADS)

Perton, M.; Neron, C.; Blouin, A.; Monchalin, J.-P.

2013-01-01

A novel technique, called laser-tapping, based on the thermoelastic excitation by laser like laser-ultrasonics has been previously introduced for inspecting honeycomb and foam core structures. If the top skin is delaminated or detached from the substrate, the detached layer is driven into vibration. The interpretation of the vibrations in terms of Lamb wave resonances is first discussed for a flat bottom hole configuration and then used to determine appropriate signal processing for samples such as honeycomb structures.

Implication of changing loading conditions on structural health monitoring utilising guided waves

NASA Astrophysics Data System (ADS)

Mohabuth, Munawwar; Kotousov, Andrei; Ng, Ching-Tai; Rose, L. R. Francis

2018-02-01

Structural health monitoring systems based on guided waves typically utilise a network of embedded or permanently attached sensors, allowing for the continuous detection of damage remote from a sensor location. The presence of damage is often diagnosed by analysing the residual signals from the structure after subtracting damage-free reference data. However, variations in environmental and operational conditions such as temperature, humidity, applied or thermally-induced stresses affect the measured residuals. A previously developed acoustoelastic formulation is here extended and employed as the basis for a simplified analytical model to estimate the effect of applied or thermally-induced stresses on the propagation characteristics of the fundamental Lamb wave modes. It is noted that there are special combinations of frequency, biaxial stress ratio and direction of wave propagation for which there is no change in the phase velocity of the fundamental anti-symmetric mode. The implication of these results in devising effective strategies to mitigate the effect of stress induced variations in guided-wave damage diagnostics is briefly discussed.

A New Electromagnetic Acoustic Transducer Design for Generating and Receiving S0 Lamb Waves in Ferromagnetic Steel Plate

PubMed Central

He, Jianpeng; Dixon, Steve; Hill, Samuel; Xu, Ke

2017-01-01

Electromagnetic acoustic transducers (EMATs) are non-contact, ultrasonic transducers that are usually kept within 5 mm from the sample surface to obtain a sufficient signal-to-noise ratio (SNR). One important issue associated with operation on a ferromagnetic plate is that the strong attraction force from the magnet can affect measurements and make scanning difficult. This paper investigates a method to generate fundamental, symmetric Lamb waves on a ferromagnetic plate. A coil-only, low-weight, generation EMAT is designed and investigated, operating at lift-offs of over 5 mm. Another design of an EMAT is investigated using a rectangular magnet with a much higher lift-off than the coil, of up to 19 mm. This results in a much lower force between the EMAT and sample, making scanning the EMAT much easier. PMID:28471377

Silicon wafer temperature monitoring using all-fiber laser ultrasonics

NASA Astrophysics Data System (ADS)

Alcoz, Jorge J.; Duffer, Charles E.

1998-03-01

Laser-ultrasonics is a very attractive technique for in-line process control in the semiconductor industry as it is compatible with the clean room environment and offers the capability to inspect parts at high-temperature. We describe measurements of the velocity of laser-generated Lamb waves in silicon wafers as a function of temperature using fiber- optic laser delivery and all-fiber interferometric sensing. Fundamental anti-symmetric Lamb-wave modes were generated in 5 inches < 111 > silicon wafers using a Nd:YAG laser coupled to a large-core multimode fiber. Generation was also performed using an array of sources created with a diffraction grating. For detection a compact fiber-optic sensor was used which is well suited for industrial environments as it is compact, rugged, stable, and low-cost. The wafers were heated up to 1000 degrees C and the temperature correlated with ultrasonic velocity measurements.

Characteristic wave speeds in the surface Brillouin scattering measurement of elastic constants of crystals

NASA Astrophysics Data System (ADS)

Every, A. G.; Kotane, L. M.; Comins, J. D.

2010-06-01

A simple and robust fitting procedure is presented for determining the three elastic constants of a cubic crystal from surface Brillouin scattering measurements carried out in the ⟨100⟩ and ⟨110⟩ directions in a (001) surface. The input data utilized are the Rayleigh surface wave velocity, the Lamb shoulder threshold velocity, and the longitudinal lateral wave velocity measured in the two directions. In fitting these velocities, use of simple closed-form expressions is made for the secular functions determining them. Corresponding expressions for the ⟨010⟩ and ⟨101¯⟩ directions in the (101) plane are also provided. The formulas for the Lamb shoulder threshold, which have not previously been available in the literature, should prove to be particularly useful, as they apply also to thin supported film structures. The procedure is applied to the determination of the elastic constants of the ternary semiconductor alloy InAs0.91Sb0.09 , yielding C11=74.4GPa , C12=40.5GPa , and C44=37.8GPa .

Intra-band gap in Lamb modes propagating in a periodic solid structure

NASA Astrophysics Data System (ADS)

Pierre, J.; Rénier, M.; Bonello, B.; Hladky-Hennion, A.-C.

2012-05-01

A laser ultrasonic technique is used to measure the dispersion of Lamb waves at a few MHz, propagating in phononic crystals made of dissymmetric air inclusions drilled throughout silicon plates. It is shown that the specific shape of the inclusions is at the origin of the intra-band gap that opens within the second Brillouin zone, at the crossing of both flexural and dilatational zero-order modes. The magnitude of the intra-band gap is measured as a function of the dissymmetry rate of the inclusions. Experimental data and the computed dispersion curves are in very good agreement.

Ultrasonic wave-based structural health monitoring embedded instrument.

PubMed

Aranguren, G; Monje, P M; Cokonaj, Valerijan; Barrera, Eduardo; Ruiz, Mariano

2013-12-01

Piezoelectric sensors and actuators are the bridge between electronic and mechanical systems in structures. This type of sensor is a key element in the integrity monitoring of aeronautic structures, bridges, pressure vessels, wind turbine blades, and gas pipelines. In this paper, an all-in-one system for Structural Health Monitoring (SHM) based on ultrasonic waves is presented, called Phased Array Monitoring for Enhanced Life Assessment. This integrated instrument is able to generate excitation signals that are sent through piezoelectric actuators, acquire the received signals in the piezoelectric sensors, and carry out signal processing to check the health of structures. To accomplish this task, the instrument uses a piezoelectric phased-array transducer that performs the actuation and sensing of the signals. The flexibility and strength of the instrument allow the user to develop and implement a substantial part of the SHM technique using Lamb waves. The entire system is controlled using configuration software and has been validated through functional, electrical loading, mechanical loading, and thermal loading resistance tests.

An intelligent signal processing and pattern recognition technique for defect identification using an active sensor network

NASA Astrophysics Data System (ADS)

Su, Zhongqing; Ye, Lin

2004-08-01

The practical utilization of elastic waves, e.g. Rayleigh-Lamb waves, in high-performance structural health monitoring techniques is somewhat impeded due to the complicated wave dispersion phenomena, the existence of multiple wave modes, the high susceptibility to diverse interferences, the bulky sampled data and the difficulty in signal interpretation. An intelligent signal processing and pattern recognition (ISPPR) approach using the wavelet transform and artificial neural network algorithms was developed; this was actualized in a signal processing package (SPP). The ISPPR technique comprehensively functions as signal filtration, data compression, characteristic extraction, information mapping and pattern recognition, capable of extracting essential yet concise features from acquired raw wave signals and further assisting in structural health evaluation. For validation, the SPP was applied to the prediction of crack growth in an alloy structural beam and construction of a damage parameter database for defect identification in CF/EP composite structures. It was clearly apparent that the elastic wave propagation-based damage assessment could be dramatically streamlined by introduction of the ISPPR technique.

Combined distributed and concentrated transducer network for failure indication

NASA Astrophysics Data System (ADS)

Ostachowicz, Wieslaw; Wandowski, Tomasz; Malinowski, Pawel

2010-03-01

In this paper algorithm for discontinuities localisation in thin panels made of aluminium alloy is presented. Mentioned algorithm uses Lamb wave propagation methods for discontinuities localisation. Elastic waves were generated and received using piezoelectric transducers. They were arranged in concentrated arrays distributed on the specimen surface. In this way almost whole specimen could be monitored using this combined distributed-concentrated transducer network. Excited elastic waves propagate and reflect from panel boundaries and discontinuities existing in the panel. Wave reflection were registered through the piezoelectric transducers and used in signal processing algorithm. Proposed processing algorithm consists of two parts: signal filtering and extraction of obstacles location. The first part was used in order to enhance signals by removing noise from them. Second part allowed to extract features connected with wave reflections from discontinuities. Extracted features damage influence maps were a basis to create damage influence maps. Damage maps indicated intensity of elastic wave reflections which corresponds to obstacles coordinates. Described signal processing algorithms were implemented in the MATLAB environment. It should be underlined that in this work results based only on experimental signals were presented.

Phononic Crystal Tunable via Ferroelectric Phase Transition

NASA Astrophysics Data System (ADS)

Xu, Chaowei; Cai, Feiyan; Xie, Shuhong; Li, Fei; Sun, Rong; Fu, Xianzhu; Xiong, Rengen; Zhang, Yi; Zheng, Hairong; Li, Jiangyu

2015-09-01

Phononic crystals (PCs) consisting of periodic materials with different acoustic properties have potential applications in functional devices. To realize more smart functions, it is desirable to actively control the properties of PCs on demand, ideally within the same fabricated system. Here, we report a tunable PC made of Ba0.7Sr0.3Ti O3 (BST) ceramics, wherein a 20-K temperature change near room temperature results in a 20% frequency shift in the transmission spectra induced by a ferroelectric phase transition. The tunability phenomenon is attributed to the structure-induced resonant excitation of A0 and A1 Lamb modes that exist intrinsically in the uniform BST plate, while these Lamb modes are sensitive to the elastic properties of the plate and can be modulated by temperature in a BST plate around the Curie temperature. The study finds opportunities for creating tunable PCs and enables smart temperature-tuned devices such as the Lamb wave filter or sensor.

A fourth order accurate finite difference scheme for the computation of elastic waves

NASA Technical Reports Server (NTRS)

Bayliss, A.; Jordan, K. E.; Lemesurier, B. J.; Turkel, E.

1986-01-01

A finite difference for elastic waves is introduced. The model is based on the first order system of equations for the velocities and stresses. The differencing is fourth order accurate on the spatial derivatives and second order accurate in time. The model is tested on a series of examples including the Lamb problem, scattering from plane interf aces and scattering from a fluid-elastic interface. The scheme is shown to be effective for these problems. The accuracy and stability is insensitive to the Poisson ratio. For the class of problems considered here it is found that the fourth order scheme requires for two-thirds to one-half the resolution of a typical second order scheme to give comparable accuracy.

Surface Brillouin scattering of opaque solids and thin supported films

PubMed

Comins; Every; Stoddart; Zhang; Crowhurst; Hearne

2000-03-01

Surface Brillouin scattering (SBS) has been used successfully for the study of acoustic excitations in opaque solids and thin supported films, at both ambient and high temperatures. A number of different systems have been investigated recently by SBS including crystalline silicon, amorphous silicon layers produced by ion bombardment and their high temperature recrystallisation, vanadium carbides, and a nickel-based superalloy. The most recent development includes the measurement of a supported gold film at high pressure. The extraction of the elastic constants is successfully accomplished by a combination of the angular dependence of surface wave velocities and the longitudinal wave threshold within the Lamb shoulder. The application of surface Green's function methods successfully reproduces the experimental SBS spectra. The discrepancies often observed between surface wave velocities and by ultrasonics measurements have been investigated and a detailed correction procedure for the SBS measurements has been developed.

Reconstruction of Rayleigh-Lamb dispersion spectrum based on noise obtained from an air-jet forcing.

PubMed

Larose, Eric; Roux, Philippe; Campillo, Michel

2007-12-01

The time-domain cross correlation of incoherent and random noise recorded by a series of passive sensors contains the impulse response of the medium between these sensors. By using noise generated by a can of compressed air sprayed on the surface of a plexiglass plate, we are able to reconstruct not only the time of flight but the whole wave forms between the sensors. From the reconstruction of the direct A(0) and S(0) waves, we derive the dispersion curves of the flexural waves, thus estimating the mechanical properties of the material without a conventional electromechanical source. The dense array of receivers employed here allow a precise frequency-wavenumber study of flexural waves, along with a thorough evaluation of the rate of convergence of the correlation with respect to the record length, the frequency, and the distance between the receivers. The reconstruction of the actual amplitude and attenuation of the impulse response is also addressed in this paper.

Changes in concentrations of trace minerals in lambs fed sericea lespedeza leaf meal pellets with or without dietary sodium molybdate.

PubMed

Acharya, M; Burke, J M; Coffey, K P; Kegley, E B; Miller, J E; Smyth, E; Welborn, M G; Terrill, T H; Mosjidis, J A; Rosenkrans, C

2016-04-01

Prolonged feeding of sericea lespedeza (SL) previously led to reduced serum concentrations of Mo, a cofactor in an enzyme complex that may be involved in weight gain. The current objective was to determine the effect of Mo supplementation on changes in serum, fecal, urine, and liver concentrations of trace minerals in lambs fed SL leaf meal pellets. Thirty ram lambs weaned in May (84 ± 1.5 d of age and 27 ± 1.1 kg; D 0) were blocked by BW, breed type (full or three-fourths Katahdin), and EBV of parasite resistance and randomly assigned to be fed 900 g/d of an alfalfa-based supplement (CON; = 10) or a SL-based supplement ( = 20) for 103 d. Supplements were formulated to be isonitrogenous and isocaloric and to meet trace mineral requirements. Within the SL group, individual lambs were administered either 5 mL water or 5 mL of water with 163.3 mg of sodium molybdate (SLMO). Serum was collected on d 28, 56, and 104; a liver sample was collected by biopsy on d 104 to determine concentrations of trace minerals. Data were analyzed using a mixed model and orthogonal contrasts. Serum concentrations of Mo increased in response to the drench and were greatest in SLMO lambs and then CON lambs and lowest in SL lambs ( < 0.001). Concentrations of Mo in the liver ( < 0.001) were similar between CON and SLMO lambs and were lower in SL lambs than other groups. Serum ( < 0.001) and liver ( = 0.013) concentrations of zinc (Zn) were reduced in both SL and SLMO lambs compared with CON lambs. Serum concentrations of cobalt (Co) increased in CON lambs compared with SL and SLMO lambs between d 0 and 56 but were similar on d 104 (diet × day, < 0.005) as with concentrations in the liver. Serum and liver concentrations of copper (Cu) were greatest ( < 0.001 and < 0.001, respectively) in CON lambs followed by SL lambs and then SLMO lambs. Serum concentrations of selenium (Se) tended ( = 0.10) to be reduced in SL lambs compared with CON and SLMO lambs, but concentrations in the liver were reduced in SL lambs compared with CON lambs and even more so in SLMO lambs ( < 0.003). Although the dietary Mo did increase stores of Mo in the animal and reduced copper, trace minerals associated with metalloproteins-Mo, copper, selenium, and zinc-were reduced in the liver of SL- and/or SLMO-fed lambs. These reductions could be associated with the lower weight gains previously observed after prolonged feeding of SL.

Sheep Stockmanship (Lambing). Youth Training Scheme. Core Exemplar Work Based Project.

ERIC Educational Resources Information Center

Further Education Staff Coll., Blagdon (England).

This trainer's guide is intended to assist supervisors of work-based career training projects in helping students gather and record information about sheep breeding, learn about treatment of diseases, prepare the lambing area, and assist with the aftercare of lambs and ewes. The guide is one in a series of core curriculum modules that is intended…

7 CFR 59.303 - Mandatory reporting of lamb carcasses and boxed lamb.

Code of Federal Regulations, 2011 CFR

2011-01-01

... following information on total carlot-based lamb carcass transactions not later than 3 p.m. central time in... per hundredweight on an F.O.B. plant basis; (2) The quantity for each lot of each transaction, quoted... price for each lot of each boxed lamb cut sale, quoted in dollars per hundredweight on a F.O.B. plant...

7 CFR 59.303 - Mandatory reporting of lamb carcasses and boxed lamb.

Code of Federal Regulations, 2012 CFR

2012-01-01

... following information on total carlot-based lamb carcass transactions not later than 3 p.m. central time in... per hundredweight on an F.O.B. plant basis; (2) The quantity for each lot of each transaction, quoted... price for each lot of each boxed lamb cut sale, quoted in dollars per hundredweight on a F.O.B. plant...

7 CFR 59.303 - Mandatory reporting of lamb carcasses and boxed lamb.

Code of Federal Regulations, 2014 CFR

2014-01-01

... following information on total carlot-based lamb carcass transactions not later than 3 p.m. central time in... per hundredweight on an F.O.B. plant basis; (2) The quantity for each lot of each transaction, quoted... price for each lot of each boxed lamb cut sale, quoted in dollars per hundredweight on a F.O.B. plant...

Wave theory in rotating systems: Schrödinger equations bridge the gaps between the equatorial β-plane and the spherical earth

NASA Astrophysics Data System (ADS)

Paldor, N.

2017-12-01

The concise and elegant wave theory developed on the equatorial β-plane by Matsuno (1966, M66 hereafter) is based on the formulation of a Schrödinger equation associated with the governing Linear Rotating Shallow Water Equations (LRSWE). The theory yields explicit expressions for the dispersion relations and meridional amplitude structures of all zonally propagating waves - Rossby, Inertia-Gravity, Kelvin and Yanai. In contrast, the spherical wave theory of Longuet-Higgins (1968) is a collection of asymptotic expansions in many sub-ranges e.g. large, small (and even negative) Lamb Number; high and low frequency; low-latitudes, etc. that rests upon extensive numerical solutions of several Ordinary Differential Equations. The difference between the two theories is highlighted by their lengths. The essential elements of the former planar study are completely revealed in just 3-4 pages including the derivation of explicit formulae for the phase speeds and amplitude meridional structures. In comtrast, the latter spherical theory contains 97 pages and the results of the numerical calculations are summarized in 30 pages of tables filled with numerical values and about 31 figures, each of which containing many separate curves! In my talk I will re-visit the wave problem on a sphere by developing several Schrödinger equations that approximate the governing eigenvalue equation associated with zonally propagating waves. Each of the Schrödinger equations approximates the original second order Ordinary Differential Equation in a different range of the 3 parameters: Lamb-Number, frequency and zonal wavenumber. As in M66, each of the Schrödinger equations yields explicit expressions for the dispersion relations and meridional amplitude structure of Rossby and Inertia-Gravity waves. In addition, the analysis shows that Yanai wave exists on a sphere even tough the zonal velocity is regular everywhere there (in contrast to the β-plane where the zonal velocity is singular everywhere) and that Kelvin waves do not exist as a separate mode (but the eastward propagating n=0 Inertia-Gravity is nearly non-dispersive). References Longuet-Higgins, M. S. Phil. Trans. Roy. Soc. London; 262, 511-607; 1968 Matsuno, T.; J. Met. Soc. Japan. 44(1), 25-43; 1966

Wavelet Spectral Finite Elements for Wave Propagation in Composite Plates with Damages - Years 3-4

DTIC Science & Technology

2014-05-23

study of Lamb wave interactions with holes and through thickness defects in thin metal plates . Distribution Code A: Approved for public release...Propagation in Composite Plates with Damages - Years 3-4 5a. CONTRACT NUMBER 5b. GRANT NUMBER FA23861214005 5c. PROGRAM ELEMENT NUMBER 6...14. ABSTRACT The objective of the proposed efforts: -Formulated Wavelet Spectral element for a healthy composite plates and used the formulated

Crack detection in fastener holes using surface acoustic wave

NASA Astrophysics Data System (ADS)

Bao, Xiao-Qi; Varadan, Vasundara V.; Varadan, Vijay K.

1995-05-01

This paper presents an investigation of the monitoring of cracks at the edge of fastener holes on plates using an ultrasonic pulse-echo technique. Our studies show that, if the surface of the plate surrounding the hold is free, an acoustic wave on the surface of the plate is able to detect the cracks located in an arc of 60 degree(s). When the inner surface of the hole is free, surface acoustic waves on the inner surface are alternate choices. For the case when all these surfaces are in tight contact with other parts, hence unavailable for mounting transducers, a particular type of Lamb wave mode is presented.

Simulation of Detecting Damage in Composite Stiffened Panel Using Lamb Waves

NASA Technical Reports Server (NTRS)

Wang, John T.; Ross, Richard W.; Huang, Guo L.; Yuan, Fuh G.

2013-01-01

Lamb wave damage detection in a composite stiffened panel is simulated by performing explicit transient dynamic finite element analyses and using signal imaging techniques. This virtual test process does not need to use real structures, actuators/sensors, or laboratory equipment. Quasi-isotropic laminates are used for the stiffened panels. Two types of damage are studied. One type is a damage in the skin bay and the other type is a debond between the stiffener flange and the skin. Innovative approaches for identifying the damage location and imaging the damage were developed. The damage location is identified by finding the intersection of the damage locus and the path of the time reversal wave packet re-emitted from the sensor nodes. The damage locus is a circle that envelops the potential damage locations. Its center is at the actuator location and its radius is computed by multiplying the group velocity by the time of flight to damage. To create a damage image for estimating the size of damage, a group of nodes in the neighborhood of the damage location is identified for applying an image condition. The image condition, computed at a finite element node, is the zero-lag cross-correlation (ZLCC) of the time-reversed incident wave signal and the time reversal wave signal from the sensor nodes. This damage imaging process is computationally efficient since only the ZLCC values of a small amount of nodes in the neighborhood of the identified damage location are computed instead of those of the full model.

Effects of supplemental organic cobalt on nutrient digestion and nitrogen balance in lambs fed forage-based diets

USDA-ARS?s Scientific Manuscript database

The objective of this study was to determine the effects of supplemental organic cobalt on nutrient digestion and nitrogen balance in lambs fed forage-based diets. Sixteen wether lambs (avg initial BW = 28.6 ± 1.3 kg) were used in a 2 × 2 Latin square and randomly allotted to one of two treatments b...

High frequency guided wave propagation in monocrystalline silicon wafers

NASA Astrophysics Data System (ADS)

Pizzolato, Marco; Masserey, Bernard; Robyr, Jean-Luc; Fromme, Paul

2017-04-01

Monocrystalline silicon wafers are widely used in the photovoltaic industry for solar panels with high conversion efficiency. The cutting process can introduce micro-cracks in the thin wafers and lead to varying thickness. High frequency guided ultrasonic waves are considered for the structural monitoring of the wafers. The anisotropy of the monocrystalline silicon leads to variations of the wave characteristics, depending on the propagation direction relative to the crystal orientation. Full three-dimensional Finite Element simulations of the guided wave propagation were conducted to visualize and quantify these effects for a line source. The phase velocity (slowness) and skew angle of the two fundamental Lamb wave modes (first anti-symmetric mode A0 and first symmetric mode S0) for varying propagation directions relative to the crystal orientation were measured experimentally. Selective mode excitation was achieved using a contact piezoelectric transducer with a custom-made wedge and holder to achieve a controlled contact pressure. The out-of-plane component of the guided wave propagation was measured using a noncontact laser interferometer. Good agreement was found with the simulation results and theoretical predictions based on nominal material properties of the silicon wafer.

Embedded fiber optic sensors for monitoring processing, quality and structural health of resin transfer molded components

NASA Astrophysics Data System (ADS)

Keulen, C.; Rocha, B.; Yildiz, M.; Suleman, A.

2011-07-01

Due to their small size and flexibility fiber optics can be embedded into composite materials with little negative effect on strength and reliability of the host material. Fiber optic sensors such as Fiber Bragg Gratings (FBG) or Etched Fiber Sensors (EFS) can be used to detect a number of relevant parameters such as flow, degree of cure, quality and structural health throughout the life of a composite component. With a detection algorithm these embedded sensors can be used to detect damage in real time while the component remains in service. This paper presents the research being conducted on the use of fiber optic sensors for process and Structural Health Monitoring (SHM) of Resin Transfer Molded (RTM) composite structures. Fiber optic sensors are used at all life stages of an RTM composite panel. A laboratory scale RTM apparatus was developed with the capability of visually monitoring the resin filling process. A technique for embedding fiber optic sensors with this apparatus has also been developed. Both FBGs and EFSs have been embedded in composite panels using the apparatus. EFSs to monitor the fabrication process, specifically resin flow have been embedded and shown to be capable of detecting the presence of resin at various locations as it is injected into the mold. Simultaneously these sensors were multiplexed on the same fiber with FBGs, which have the ability to measure strain. Since multiple sensors can be multiplexed on a single fiber the number of ingress/egress locations required per sensor can be significantly reduced. To characterize the FBGs for strain detection tensile test specimens with embedded FBG sensors have been produced. These specimens have been instrumented with a resistive strain gauge for benchmarking. Both specimens and embedded sensors were characterized through tensile testing. Furthermore FBGs have been embedded into composite panels in a manner that is conducive to detection of Lamb waves generated with a centrally located PZT. To sense Lamb waves a high speed, high precision sensing technique is required to acquire data from embedded FBGs due to the high velocities and small strain amplitudes of these guided waves. A technique based on a filter consisting of a tunable FBG was developed. Since this filter is not dependant on moving parts, tests executed with this filter concluded with the detection of Lamb waves, removing the influence of temperature and operational strains. A damage detection algorithm was developed to detect and localize cracks and delaminations.

Development of an ultrasonic inspection robot using an electromagnetic acoustic transducer for a Lamb wave and an SH-plate wave.

PubMed

Murayama, Riichi; Makiyama, Shunnichi; Kodama, Mitutoshi; Taniguchi, Yasutoshi

2004-04-01

For inspection of a storage tank and pipeline in service, the application of an automatic inspection system (nondestructive inspection robot) is desirable, because manual inspection is difficult to perfectly and exactly perform due to the enormous amount of inspection needed. However, an ultrasonic nondestructive inspection robot with a piezoelectric oscillator needs to touch only the material surface to be directly inspected using a coupling medium. That is, the material surface and the sensor must always be held by constant pressure in the vertical direction on the material side. Actually, it is difficult to overcome these problems; thus an ultrasonic inspection robot could not be widely applied. We then tried to develop an ultrasonic inspection robot with an electromagnetic acoustic transducer (EMAT) which did not require a coupling medium to inspect the circumferential pipe parts. We developed a special EMAT that could transmit and receive alternately a Lamb wave with high sensitivity and a SH-plate wave without influence by the welded part. The method by which the inspection robot turned around the direction of the steel pipe surroundings was executed by observing the tape pasted in the direction of the steel pipe surroundings with an installed CCD camera. In this report, the basic mechanism of this inspection robot and an examination of results are described.

An Extracorporeal Artificial Placenta Supports Extremely Premature Lambs for One Week

PubMed Central

Bryner, Benjamin; Gray, Brian; Perkins, Elena; Davis, Ryan; Hoffman, Hayley; Barks, John; Owens, Gabe; Bocks, Martin; Rojas-Peña, Alvaro; Hirschl, Ronald; Bartlett, Robert; Mychaliska, George

2015-01-01

Purpose The treatment of extreme prematurity remains an unsolved problem. We developed an artificial placenta (AP) based on extracorporeal life support (ECLS) that simulates the intrauterine environment and provides gas exchange without mechanical ventilation (MV), and compared it to the current standard of neonatal care. Methods Extremely premature lambs (110-120d; term=145d) were used. AP lambs (n=9) were cannulated (jugular drainage, umbilical vein reinfusion) for ECLS .Control lambs (n=7) were intubated, ventilated, given surfactant, and transitioned to high-frequency oscillatory ventilation. All lambs received parenteral nutrition, antibiotics, and steroids. Hemodynamics, blood gases, hemoglobin, and circuit flows were measured. Results Four premature lambs survived for 1 week on the AP; one survived 6 days. Adequate oxygenation and ventilation were provided by the AP. The MV lambs survived 2-8 hours. Each of these lambs experienced a transient improvement with surfactant, but developed progressive hypercapnea and hypoxia despite high airway pressures and HFOV. Conclusions Extremely premature lambs were supported for 1 week with the AP with hemodynamic stability and adequate gas exchange; mechanically ventilated lambs succumbed within 8 hours. Further studies will assess control of fetal circulation and organ maturation on the AP. PMID:25598091

Parasitic gastro-enteritis in lambs — A model for estimating the timing of the larval emergence peak

NASA Astrophysics Data System (ADS)

Starr, J. R.; Thomas, R. J.

1980-09-01

The life history of the nematode parasites of domestic ruminants usually involves the development and survival of free-living stages on pasture. The pasture is, therefore, the site of deposition, development and transmission of nematode infection and meteorological factors affecting the pasture will affect the parasites. Recently Thomas and Starr (1978) discussed an empirical technique for forecasting the timing of the summer wave of gastro-intestinal parasitism in North-East England in the lamb crop using meteorological data and in particular estimates of the duration of “surface wetness”. This paper presents an attempt to model “surface wetness” and the temperature limitation to nematode development.

Evaluation of multilayered pavement structures from measurements of surface waves

USGS Publications Warehouse

Ryden, N.; Lowe, M.J.S.; Cawley, P.; Park, C.B.

2006-01-01

A method is presented for evaluating the thickness and stiffness of multilayered pavement structures from guided waves measured at the surface. Data is collected with a light hammer as the source and an accelerometer as receiver, generating a synthetic receiver array. The top layer properties are evaluated with a Lamb wave analysis. Multiple layers are evaluated by matching a theoretical phase velocity spectrum to the measured spectrum. So far the method has been applied to the testing of pavements, but it may also be applicable in other fields such as ultrasonic testing of coated materials. ?? 2006 American Institute of Physics.

Effects of dam breed and dietary source of n-3 polyunsaturated fatty acids on the growth and carcass characteristics of lambs sourced from hill sheep flocks.

PubMed

Annett, R W; Carson, A F; Dawson, L E R; Kilpatrick, D J

2011-05-01

The objectives of this study were to investigate the effect of dietary lipid source on the growth and carcass characteristics of lambs sourced from a range of crossbred hill ewes. Over a 2-year period, 466 lambs representing the progeny of Scottish Blackface (BF × BF), Swaledale (SW) × BF, North Country Cheviot (CH) × BF, Lleyn (LL) × BF and Texel (T) × BF ewes were sourced from six commercial hill flocks and finished on one of four diets: grass pellets (GP), cereal-based concentrate (CC), CC enriched with oilseed rape (CR) and CC enriched with fish oil (CF). Dry matter intake (DMI) was highest (P < 0.001) in lambs offered GP; however, carcass weight gain (CWG) and feed conversion efficiency were higher (P < 0.001) in lambs fed concentrate-based diets. For lambs offered concentrate-based diets, DMI and live weight gain were lower (P < 0.001) for CF than CC or CR. Lambs with T × BF dams achieved a higher (P < 0.05) daily CWG and CWG/kg DMI than BF × BF, SW × BF or LL × BF dams. When lambs were slaughtered at fat score 3, CH × BF, LL × BF and T × BF dams increased carcass weight by 0.8 to 1.4 kg (P < 0.001) and conformation score (CS) by 0.2 to 0.4 units (P < 0.001) compared with BF × BF or SW × BF dams. However, breed effects on carcass conformation were reduced by 50% when lambs were slaughtered at a constant carcass weight. Diets CC and CR increased carcass weight by 0.8 to 1.6 kg (P < 0.001) and CS by 0.1 to 0.3 units (P < 0.001) compared with GP and CF. Both, dam breed and dietary effects on carcass conformation were associated with an increase (P < 0.001) in shoulder width of the lambs. Lambs fed CF and slaughtered at a constant carcass weight had more subcutaneous fat over the Longissumus dorsi (P < 0.05), Iliocostalis thoracis (P < 0.001) and Obliquus internus abdominis (P < 0.001) compared with those fed CC. However, these effects were removed when lambs were slaughtered at a constant fat score. At both endpoints, lambs from T × BF dams contained less (P < 0.05) perinephric and retroperitoneal fat than SW × BF or LL × BF dams fed GP or CC, respectively. The results from this study show that using crossbred ewes sired by CH, LL or T sires will increase carcass weight and improve carcass conformation of lambs sourced from hill flocks. Inclusion of oilseed rape in lamb finishing diets had only minor effects on performance compared with a standard CC but feeding fish oil or GP impacted negatively on lamb growth and carcass quality.

Modeling of Lamb Waves and Application to Crack Identification

DTIC Science & Technology

2009-09-01

and Structures, vol. 13, pp. 621–630, 2004. [13] Seth S Kessler , S. Mark Spearing, and Constantinos Soutis, “Damage detection in composite materials...growth in metallic structures. Kessler et al. [13] presented part of an experimental and analytical survey of candidate methods for in-situ damage

Defects Detection and Characterization Using Leaky Lamb Wave (LLW) Dispersion Data

NASA Technical Reports Server (NTRS)

Bar-Cohen, Y.; Mal, A.; Chang, Z.

1998-01-01

Composite materials are being used at a significant level of usage for flaw critical structures and they are taking a growing percentage of the makeup of aircraft and spacecraft. Composite structues are now reaching service duration, for which the issue of aging is requiring adquate attention.

Stable isotopes to discriminate lambs fed herbage or concentrate both obtained from C(3) plants.

PubMed

Moreno-Rojas, Jose M; Vasta, Valentina; Lanza, Alfio; Luciano, Giuseppe; Ladroue, Virginie; Guillou, Claude; Priolo, Alessandro

2008-12-01

This study was aimed at determining whether isotopic ratio mass spectrometry (IRMS) enables us to discriminate between lambs fed herbage or concentrate, both obtained from C(3) plants, and those fed a concentrate obtained from C(4) plants. Thirty-four Comisana male lambs (age 45 days) were assigned to three feeding treatments. Fourteen lambs were fed vetch (Vicia sativa) ad libitum. Another fourteen lambs received a barley-based concentrate. The remaining six lambs were fed a maize-based concentrate. After 60 days of experimental treatment the animals were slaughtered and the wool, perirenal fat and muscle longissimus dorsi were sampled. The delta(13)C and delta(15)N values of the muscle, wool and feed were measured by continuous flow elemental analysis (CF-EA)-IRMS. The delta(13)C of the fat was determined likewise. The isotopic composition of the tissues reflected that of the three diets. For the lambs which were fed herbage the muscle delta(13)C values were higher (P < 0.0005) and delta(15)N values were lower (P < 0.0005) than those of the lambs receiving concentrates. The delta(15)N and delta(13)C values in the muscle and delta(13)C values in the adipose tissue allowed perfect discrimination between the lambs fed the three different diets. The regression between the delta(13)C values measured in muscle and in wool of lambs was linear (R(2) = 0.99; P < 0.0005). This result shows that delta(13)C measured in the wool can predict muscle delta(13)C distribution, suggesting that wool is a valuable matrix for meat authentication.

Polwarth and Texel ewe parturition duration and its association with lamb birth asphyxia.

PubMed

Dutra, F; Banchero, G

2011-10-01

The objective of the present study was to test the hypothesis that parturition duration is related to birth asphyxia in lambs and that asphyxia affects newborn lamb viability and vigor. Two sire and dam genotypes (Texel: TX; Polwarth: PW) and their crosses were represented in the study. Eighty lambs (25 PW sire × PW dam, 13 TX × TX, 25 TX × PW, and 17 PW × TX) born to 69 grazing ewes were used. At birth, the log₁₀ length of the second stage of parturition, birth weight, placental weight, and several body measurements were recorded on all lambs, and jugular blood samples were analyzed with the i-Stat Portable Clinical Analyzer (Abbott, Montevideo, Uruguay). A modified Apgar viability score at birth and lamb behavior during their first hour of life were recorded. Brain weight, muscle:bone ratio, and bone density were recorded in 20 male lambs (5 from each breed group) that were euthanized and dissected 24 h after birth. Data were analyzed by linear regression, least squares ANOVA, and ordinal and binary logistic regressions. Mean blood gas and acid-base variables were 7.21 ± 0.09 for pH, 18.4 ± 9.8 mmHg for partial pressure of oxygen, 53 ± 12.5 mmHg for partial pressure of carbon dioxide, and -4 ± 5.1 mmol/L for extracellular fluid base excess. Parturition duration increased with birth weight (P < 0.001) and was shorter in TX ewes (P < 0.001), female lambs (P < 0.05), twins (P < 0.09), and twin females (sex × litter size interaction, P < 0.02). Twenty-six (32.9%) lambs were born asphyxiated (pO₂ < 10 mmHg or pH <7.1). Parturition duration increased the risk of asphyxia (P < 0.001), decreased the viability score (P < 0.001), and increased the latency to suckle the udder (P < 0.05). Twin-born lambs presented at birth a 16-fold greater risk of asphyxia (P < 0.01) and reduced placental efficiency (P < 0.05). Texel-sired lambs appeared immature at birth, with less bone density (P < 0.05), smaller brain (P < 0.05), shorter forelimbs (P < 0.05), greater anterior (P < 0.001) and posterior (P < 0.05) neck circumference, and greater muscle:bone ratio (P < 0.05). Immaturity may explain greater TX biotype survival. Together these results demonstrate that a relationship exists between parturition duration, neonatal viability and behavior, and acid-base balance values in single- and twin-born lambs, suggesting that birth asphyxia is an important risk factor in perinatal lamb mortality.

Multimodal approach to seismic pavement testing

USGS Publications Warehouse

Ryden, N.; Park, C.B.; Ulriksen, P.; Miller, R.D.

2004-01-01

A multimodal approach to nondestructive seismic pavement testing is described. The presented approach is based on multichannel analysis of all types of seismic waves propagating along the surface of the pavement. The multichannel data acquisition method is replaced by multichannel simulation with one receiver. This method uses only one accelerometer-receiver and a light hammer-source, to generate a synthetic receiver array. This data acquisition technique is made possible through careful triggering of the source and results in such simplification of the technique that it is made generally available. Multiple dispersion curves are automatically and objectively extracted using the multichannel analysis of surface waves processing scheme, which is described. Resulting dispersion curves in the high frequency range match with theoretical Lamb waves in a free plate. At lower frequencies there are several branches of dispersion curves corresponding to the lower layers of different stiffness in the pavement system. The observed behavior of multimodal dispersion curves is in agreement with theory, which has been validated through both numerical modeling and the transfer matrix method, by solving for complex wave numbers. ?? ASCE / JUNE 2004.

Scattering of Lamb waves in a composite plate

NASA Technical Reports Server (NTRS)

Bratton, Robert; Datta, Subhendu; Shah, Arvind

1991-01-01

A combined analytical and finite element technique is developed to gain a better understanding of the scattering of elastic waves by defects. This hybrid method is capable of predicting scattered displacements from arbitrary shaped defects as well as inclusions of different material. The continuity of traction and displacements at the boundaries of the two areas provided the necessary equations to find the nodal displacements and expansion coefficients. Results clearly illustrate the influence of increasing crack depth on the scattered signal.

Lamb wave band gaps in a double-sided phononic plate

NASA Astrophysics Data System (ADS)

Wang, Peng; Chen, Tian-Ning; Yu, Kun-Peng; Wang, Xiao-Peng

2013-02-01

In this paper, we report on the theoretical investigation of the propagation characteristics of Lamb wave in a phononic crystal structure constituted by a square array of cylindrical stubs deposited on both sides of a thin homogeneous plate. The dispersion relations, the power transmission spectra, and the displacement fields of the eigenmodes are studied by using the finite-element method. We investigate the evolution of band gaps in the double-sided phononic plate with stub height on both sides arranged from an asymmetrical distribution to a symmetrical distribution gradually. Numerical results show that as the double stubs in a unit cell arranged more symmetrically on both sides, band width shifts, new band gaps appear, and the bands become flat due to localized resonant modes which couple with plate modes. Specially, more band gaps and flat bands can be found in the symmetrical system as a result of local resonances of the stubs which interact in a stronger way with the plate modes. Moreover, the symmetrical double-sided plate exhibits lower and smaller band gap than that of the asymmetrical plate. These propagation properties of elastic or acoustic waves in the double-sided plate can potentially be utilized to generate filters, slow the group velocity, low-frequency sound insulation, and design acoustic sensors.

Experimental observation of a large low-frequency band gap in a polymer waveguide

NASA Astrophysics Data System (ADS)

Miniaci, Marco; Mazzotti, Matteo; Radzieński, Maciej; Kherraz, Nesrine; Kudela, Pawel; Ostachowicz, Wieslaw; Morvan, Bruno; Bosia, Federico; Pugno, Nicola M.

2018-02-01

The quest for large and low frequency band gaps is one of the principal objectives pursued in a number of engineering applications, ranging from noise absorption to vibration control, to seismic wave abatement. For this purpose, a plethora of complex architectures (including multi-phase materials) and multi-physics approaches have been proposed in the past, often involving difficulties in their practical realization. To address this issue, in this work we propose an easy-to-manufacture design able to open large, low frequency complete Lamb band gaps exploiting a suitable arrangement of masses and stiffnesses produced by cavities in a monolithic material. The performance of the designed structure is evaluated by numerical simulations and confirmed by Scanning Laser Doppler Vibrometer (SLDV) measurements on an isotropic polyvinyl chloride plate in which a square ring region of cross-like cavities is fabricated. The full wave field reconstruction clearly confirms the ability of even a limited number of unit cell rows of the proposed design to efficiently attenuate Lamb waves. In addition, numerical simulations show that the structure allows to shift of the central frequency of the BG through geometrical modifications. The design may be of interest for applications in which large BGs at low frequencies are required.

Effect of concentrate level and slaughter body weight on growth performances, carcass traits and meat quality of Barbarine lambs fed oat hay based diet.

PubMed

Majdoub-Mathlouthi, L; Saïd, B; Say, A; Kraiem, K

2013-03-01

This study was conducted to evaluate concentrate level (CL) and slaughter body weight (SW) effects on growth performances, carcass traits and meat quality of Barbarine lambs. Twenty-four weaned male lambs (23.1 kg), receiving an oat-hay based diet, were allotted into two groups. The LCL group received low concentrate level (300 g) and the HCL group received high concentrate level (600 g). Lambs were slaughtered at two prefixed weights (35 and 42 kg). For each group and each weight, six lambs were slaughtered. Lambs from HCL group had higher ADG, carcass yields, carcass compactness and subcutaneous fat thickness, and lower carcass meat proportion. CL increase did not affect meat pH, meat and fat color, chemical and fatty acid composition. Late slaughtering improved carcass yields and increased carcass adiposity. However, it did not affect carcass meat proportion and shoulder tissue composition. SW had effect on meat color and fatty acid composition. Copyright © 2012 Elsevier Ltd. All rights reserved.

Plane Wave SH₀ Piezoceramic Transduction Optimized Using Geometrical Parameters.

PubMed

Boivin, Guillaume; Viens, Martin; Belanger, Pierre

2018-02-10

Structural health monitoring is a prominent alternative to the scheduled maintenance of safety-critical components. The nondispersive nature as well as the through-thickness mode shape of the fundamental shear horizontal guided wave mode (SH 0 ) make it a particularly attractive candidate for ultrasonic guided wave structural health monitoring. However, plane wave excitation of SH 0 at a high level of purity remains challenging because of the existence of the fundamental Lamb modes (A 0 and S 0 ) below the cutoff frequency thickness product of high-order modes. This paper presents a piezoelectric transducer concept optimized for plane SH 0 wave transduction based on the transducer geometry. The transducer parameter exploration was initially performed using a simple analytical model. A 3D multiphysics finite element model was then used to refine the transducer design. Finally, an experimental validation was conducted with a 3D laser Doppler vibrometer system. The analytical model, the finite element model, and the experimental measurement showed excellent agreement. The modal selectivity of SH 0 within a 20 ∘ beam opening angle at the design frequency of 425 kHz in a 1.59 mm aluminum plate was 23 dB, and the angle of the 6 dB wavefront was 86 ∘ .

Inspection Method for Contact Condition of Soil on the Surface of Underground Pipe Utilizing Resonance of Transverse Lamb Wave

NASA Astrophysics Data System (ADS)

Tanigawa, Hiroshi; Seno, Hiroaki; Watanabe, Yoshiaki; Nakajima, Koshiro

1998-05-01

A nondestructive inspection method to estimate the contact condition of soil on the surface of an underground pipe, utilizing the resonance of a transverse Lamb wave circulating along the pipe wall is proposed.The Q factor of the resonance is considered and measured under some contact conditions by sweeping the vibrating frequency in a 150-mm-inner diameter Fiberglass Reinforced Plastic Mortar (FRPM) pipe. It is confirmed that the Q factor shows a clear response to the change in the contact conditions. For example, the Q factor is 8.4 when the pipe is in ideal contact with the soil plane and goes up to 19.2 when a 100-mm-diameter void is located at the contact surface of the soil.The spatial resolution of the proposed inspection method is also measured by moving the sensing point along the direction of laying the length of the pipe into a 85-mm-diameter void. The resolution of the proposed method is estimated at about 50 mm.

[Liposomal-amphotericin B efficacy and safety].

PubMed

Hamada, Yukihiro; Komatsu, Toshiaki; Seto, Yoshinori; Matsubara, Hajime; Kume, Hikaru; Sunakawa, Keisuke; Yago, Kazuo

2010-03-01

Liposomal amphotericin B (L-AMB), a lipid-based amphotericin B formulation, has been used in Japan since June 2006 to treat fungal infection. In the 3 years since L-AMB was launched, few reports have been made on its status. To ensure its appropriate use, we restrospectively reviewed its efficacy and safety in treating fungal infections. 25 subjects with fungal infection treated with L-AMB from April 2007 until February 2008. Of those, 16 showed clinical improvement. Elevated serum creatinine occurred in 1 and decreased serum potassium in 6. We found a positive relationship between the serum potassium decrease and L-AMB dose. Logistic regression analysis of this relationship showed that serum potassium tended to fall on day 5 to 6 of L-AMB administration. While L-AMB appears highly effective in fungal infection, it requires serum potassium monitoring to ensure patient safety.

Modelling ultrasound guided wave propagation for plate thickness measurement

NASA Astrophysics Data System (ADS)

Malladi, Rakesh; Dabak, Anand; Murthy, Nitish Krishna

2014-03-01

Structural Health monitoring refers to monitoring the health of plate-like walls of large reactors, pipelines and other structures in terms of corrosion detection and thickness estimation. The objective of this work is modeling the ultrasonic guided waves generated in a plate. The piezoelectric is excited by an input pulse to generate ultrasonic guided lamb waves in the plate that are received by another piezoelectric transducer. In contrast with existing methods, we develop a mathematical model of the direct component of the signal (DCS) recorded at the terminals of the piezoelectric transducer. The DCS model uses maximum likelihood technique to estimate the different parameters, namely the time delay of the signal due to the transducer delay and amplitude scaling of all the lamb wave modes due to attenuation, while taking into account the received signal spreading in time due to dispersion. The maximum likelihood estimate minimizes the energy difference between the experimental and the DCS model-generated signal. We demonstrate that the DCS model matches closely with experimentally recorded signals and show it can be used to estimate thickness of the plate. The main idea of the thickness estimation algorithm is to generate a bank of DCS model-generated signals, each corresponding to a different thickness of the plate and then find the closest match among these signals to the received signal, resulting in an estimate of the thickness of the plate. Therefore our approach provides a complementary suite of analytics to the existing thickness monitoring approaches.

Application of optical interferometry in focused acoustic field measurement

NASA Astrophysics Data System (ADS)

Wang, Yuebing; Sun, Min; Cao, Yonggang; Zhu, Jiang

2018-07-01

Optical interferometry has been successfully applied in measuring acoustic pressures in plane-wave fields and spherical-wave fields. In this paper, the "effective" refractive index for focused acoustic fields was developed, through numerical simulation and experiments, the feasibility of the optical method in measuring acoustic fields of focused transducers was proved. Compared with the results from a membrane hydrophone, it was concluded that the optical method has good spatial resolution and is suitable for detecting focused fields with fluctuant distributions. The influences of a few factors (the generated lamb wave, laser beam directivity, etc.) were analyzed, and corresponding suggestions were proposed for effective application of this technology.

3D Ultrasonic Wave Simulations for Structural Health Monitoring

NASA Technical Reports Server (NTRS)

Campbell, Leckey Cara A/; Miler, Corey A.; Hinders, Mark K.

2011-01-01

Structural health monitoring (SHM) for the detection of damage in aerospace materials is an important area of research at NASA. Ultrasonic guided Lamb waves are a promising SHM damage detection technique since the waves can propagate long distances. For complicated flaw geometries experimental signals can be difficult to interpret. High performance computing can now handle full 3-dimensional (3D) simulations of elastic wave propagation in materials. We have developed and implemented parallel 3D elastodynamic finite integration technique (3D EFIT) code to investigate ultrasound scattering from flaws in materials. EFIT results have been compared to experimental data and the simulations provide unique insight into details of the wave behavior. This type of insight is useful for developing optimized experimental SHM techniques. 3D EFIT can also be expanded to model wave propagation and scattering in anisotropic composite materials.

Lamb Wave Stiffness Characterization of Composites Undergoing Thermal-Mechanical Aging

NASA Technical Reports Server (NTRS)

Seale, Michael D.; Madaras, Eric I.

2004-01-01

The introduction of new, advanced composite materials into aviation systems requires a thorough understanding of the long term effects of combined thermal and mechanical loading upon those materials. Analytical methods investigating the effects of intense thermal heating combined with mechanical loading have been investigated. The damage mechanisms and fatigue lives were dependent on test parameters as well as stress levels. Castelli, et al. identified matrix dominated failure modes for out-of-phase cycling and fiber dominated damage modes for in-phase cycling. In recent years, ultrasonic methods have been developed that can measure the mechanical stiffness of composites. To help evaluate the effect of aging, a suitably designed Lamb wave measurement system is being used to obtain bending and out-of-plane stiffness coefficients of composite laminates undergoing thermal-mechanical loading. The system works by exciting an antisymmetric Lamb wave and calculating the velocity at each frequency from the known transducer separation and the measured time-of-flight. The same peak in the waveforms received at various distances is used to measure the time difference between the signals. The velocity measurements are accurate and repeatable to within 1% resulting in reconstructed stiffness values repeatable to within 4%. Given the material density and plate thickness, the bending and out-of-plane shear stiffnesses are calculated from a reconstruction of the dispersion curve. A mechanical scanner is used to move the sensors over the surface to map the time-of-flight, velocity, or stiffnesses of the entire specimen. Access to only one side of the material is required and no immersion or couplants are required because the sensors are dry coupled to the surface of the plate. In this study, the elastic stiffnesses D(sub 11), D(sub 22), A(sub 44), and A(sub 55) as well as time-of-flight measurements for composite samples that have undergone combined thermal and mechanical aging for a duration of 10,000 hours are reported.

Changes in hematology, serum biochemistry, and gastrointestinal nematode infection in lambs fed sericea lespedeza with or without dietary sodium molybdate.

PubMed

Acharya, M; Burke, J M; Coffey, K P; Kegley, E B; Miller, J E; Huff, G R; Smyth, E; Terrill, T H; Mosjidis, J A; Rosenkrans, C

2015-04-01

Sericea lespedeza (SL; Lespedeza cuneata) is a legume rich in condensed tannins that can be grazed or fed to small ruminants for parasite control. Condensed tannins, a secondary plant compound in SL, may lead to unintended consequences such as changes in production. In our preliminary research, there was consistently a reduction in serum and liver concentrations of Mo. The objective of this study was to determine the effect of SL with or without Mo supplementation on changes in BW, hematology, and serum biochemistry in lambs. Thirty ram lambs weaned in May (84 ± 1.5 d of age; 27 ± 1.1 kg) were blocked by BW, breed type (full or three-fourths Katahdin), and EBV of parasite resistance and randomly assigned to be fed 900 g of alfalfa-based supplement (CON; n = 10) or SL-based supplement (n = 20) for 103 d. Supplements were formulated to be isonitrogenous and isocaloric and to meet trace mineral requirements. Within the SL diet, half of the lambs received 490 mg sodium molybdate weekly (SLMO). Body condition scores and BW were determined every 14 d and blood and feces collected to determine hematological and serum biochemical profiles and fecal egg counts (FEC). Data were analyzed using a mixed model with repeated measures and orthogonal contrasts. The white blood cell counts tended to be reduced in SL- and SLMO-fed lambs compared with CON-fed lambs (P < 0.06), which was associated with a reduction in neutrophils (P < 0.001). Red blood cell counts were also reduced in SL but not SLMO lambs compared with CON lambs (P < 0.04). There was a reduction in blood packed cell volume (P < 0.04) and serum concentrations of albumin (P < 0.001) and creatinine (P < 0.02) in both SL and SLMO lambs compared with CON lambs. Similarly, concentrations of blood urea nitrogen were reduced in both SL and SLMO lambs, but differences among dietary treatments disappeared after 42 d of feeding (treatment × day, P < 0.004). Serum concentrations of total proteins were reduced only in SLMO lambs compared with other lambs (P < 0.001). Body weight and FEC were similar among dietary treatments. Means of all measurements were within a normal range, even though there were subtle but significant differences between dietary groups. Feeding a diet high in condensed tannin-rich SL did not lead to serious effects on hematology or serum biochemistry in lambs.

Effect of feeding Mucuna pruriens on helminth parasite infestation in lambs.

PubMed

Huisden, C M; Adesogan, A T; Gaskin, J M; Courtney, C H; Raji, A M; Kang, T

2010-02-17

Mucuna pruriens is a tropical legume anecdotally reputed to have anthelmintic properties. This study was conducted to examine the validity of such claims. The aim of this study was to determine if ingestion of Mucuna seeds reduces helminth parasite infestation in lambs. Thirty-six Dorper x Katahdin ram lambs were assigned to three treatments, a cottonseed meal based control diet, a diet in which Mucuna replaced cottonseed meal and the control diet with levamisole (7.5mg/kg body weight) administration. All diets were isonitrogenous and isocaloric. The 12 lambs in each treatment were assigned randomly to 4 pens, each containing 3 lambs. Lambs were trickle infected three times per week by gavage with infectious Haemonchus contortus larvae (2000 larvae/lamb) for 3 weeks. Levamisole treatment decreased fecal egg counts by 87% and abomasal worm counts by 83%. Mucuna intake did not statistically affect fecal egg counts or abomasal worm counts, though numerical (P>0.10) reductions of 7.4% and 18.1%, respectively were evident. Anemia indicators, feed intake, and lamb growth were unaffected by treatment. Levamisole reduced the Haemonchus parasite burden in lambs significantly but feeding Mucuna reduced the burden by levels unlikely to eliminate the clinical effects of parasitism. Copyright 2009 Elsevier Ireland Ltd. All rights reserved.

Microstructural and Defect Characterization in Ceramic Composites Using an Ultrasonic Guided Wave Scan System

NASA Technical Reports Server (NTRS)

Roth, D. J.; Cosgriff, L. M.; Martin, R. E.; Verrilli, M. J.; Bhatt, R. T.

2003-01-01

In this study, an ultrasonic guided wave scan system was used to characterize various microstructural and flaw conditions in two types of ceramic matrix composites, SiC/SiC and C/SiC. Rather than attempting to isolate specific lamb wave modes to use for characterization (as is desired for many types of guided wave inspection problems), the guided wave scan system utilizes the total (multi-mode) ultrasonic response in its inspection analysis. Several time and frequency-domain parameters are calculated from the ultrasonic guided wave signal at each scan location to form images. Microstructural and defect conditions examined include delamination, density variation, cracking, and pre/ post-infiltration. Results are compared with thermographic imaging methods. Although the guided wave technique is commonly used so scanning can be eliminated, applying the technique in the scanning mode allows a more precise characterization of defect conditions.

Lateral acoustic wave resonator comprising a suspended membrane of low damping resonator material

DOEpatents

Olsson, Roy H.; El-Kady; , Ihab F.; Ziaei-Moayyed, Maryam; Branch; , Darren W.; Su; Mehmet F.,; Reinke; Charles M.,

2013-09-03

A very high-Q, low insertion loss resonator can be achieved by storing many overtone cycles of a lateral acoustic wave (i.e., Lamb wave) in a lithographically defined suspended membrane comprising a low damping resonator material, such as silicon carbide. The high-Q resonator can sets up a Fabry-Perot cavity in a low-damping resonator material using high-reflectivity acoustic end mirrors, which can comprise phononic crystals. The lateral overtone acoustic wave resonator can be electrically transduced by piezoelectric couplers. The resonator Q can be increased without increasing the impedance or insertion loss by storing many cycles or wavelengths in the high-Q resonator material, with much lower damping than the piezoelectric transducer material.

Hidden corrosion detection in aircraft aluminum structures using laser ultrasonics and wavelet transform signal analysis.

PubMed

Silva, M Z; Gouyon, R; Lepoutre, F

2003-06-01

Preliminary results of hidden corrosion detection in aircraft aluminum structures using a noncontact laser based ultrasonic technique are presented. A short laser pulse focused to a line spot is used as a broadband source of ultrasonic guided waves in an aluminum 2024 sample cut from an aircraft structure and prepared with artificially corroded circular areas on its back surface. The out of plane surface displacements produced by the propagating ultrasonic waves were detected with a heterodyne Mach-Zehnder interferometer. Time-frequency analysis of the signals using a continuous wavelet transform allowed the identification of the generated Lamb modes by comparison with the calculated dispersion curves. The presence of back surface corrosion was detected by noting the loss of the S(1) mode near its cutoff frequency. This method is applicable to fast scanning inspection techniques and it is particularly suited for early corrosion detection.

Visualization of Lamb Wave Interaction with a 5 mm Fatigue Crack using 1D Ultra High Frequency Laser Doppler Vibrometry

DTIC Science & Technology

2011-09-01

detection of a fatigue crack via 3D LDV measurements, both in aluminum plates. All the referenced LDV/guided wave studies made use of PZT or similar...Figure 1a). (b) (a) (c) Figure 1: (a) Test specimen in MTS fatigue test machine, (b) hole with 5 mm crack, (c) PZT placement with...mm thick aluminum plates with a small (1.59 mm) center hole added to facilitate growth of a fatigue crack. One plate was left undamaged while the

High-temperature elastic properties of a nickel-based superalloy studied by surface Brillouin scattering

NASA Astrophysics Data System (ADS)

Zhang, X.; Stoddart, P. R.; Comins, J. D.; Every, A. G.

2001-03-01

Surface Brillouin scattering (SBS) has been used to study the thermally induced surface vibrations (phonons) and thereby obtain the elastic properties of the nickel-based superalloy CMSX-4. SBS spectra have been acquired for a range of wavevector directions in the (001) surface in the single-crystal specimen to determine the angular variation of SAW velocities and the nature of the various excitations. Rayleigh and pseudo-surface acoustic waves as well as the details of the Lamb shoulder are studied, and the elastic constants and engineering moduli are determined using different, but self-consistent, methods at ambient and high temperatures. Calculations of the SBS spectra using surface Green function methods are in good agreement with the experimental results.

Automated laser-based barely visible impact damage detection in honeycomb sandwich composite structures

NASA Astrophysics Data System (ADS)

Girolamo, D.; Girolamo, L.; Yuan, F. G.

2015-03-01

Nondestructive evaluation (NDE) for detection and quantification of damage in composite materials is fundamental in the assessment of the overall structural integrity of modern aerospace systems. Conventional NDE systems have been extensively used to detect the location and size of damages by propagating ultrasonic waves normal to the surface. However they usually require physical contact with the structure and are time consuming and labor intensive. An automated, contactless laser ultrasonic imaging system for barely visible impact damage (BVID) detection in advanced composite structures has been developed to overcome these limitations. Lamb waves are generated by a Q-switched Nd:YAG laser, raster scanned by a set of galvano-mirrors over the damaged area. The out-of-plane vibrations are measured through a laser Doppler Vibrometer (LDV) that is stationary at a point on the corner of the grid. The ultrasonic wave field of the scanned area is reconstructed in polar coordinates and analyzed for high resolution characterization of impact damage in the composite honeycomb panel. Two methodologies are used for ultrasonic wave-field analysis: scattered wave field analysis (SWA) and standing wave energy analysis (SWEA) in the frequency domain. The SWA is employed for processing the wave field and estimate spatially dependent wavenumber values, related to discontinuities in the structural domain. The SWEA algorithm extracts standing waves trapped within damaged areas and, by studying the spectrum of the standing wave field, returns high fidelity damage imaging. While the SWA can be used to locate the impact damage in the honeycomb panel, the SWEA produces damage images in good agreement with X-ray computed tomographic (X-ray CT) scans. The results obtained prove that the laser-based nondestructive system is an effective alternative to overcome limitations of conventional NDI technologies.

Study on the application of shear-wave elastography to thin-layered media and tubular structure: Finite-element analysis and experiment verification

NASA Astrophysics Data System (ADS)

Jang, Jun-keun; Kondo, Kengo; Namita, Takeshi; Yamakawa, Makoto; Shiina, Tsuyoshi

2016-07-01

Shear-wave elastography (SWE) enables the noninvasive and quantitative evaluation of the mechanical properties of human soft tissue. Generally, shear-wave velocity (C S) can be estimated using the time-of-flight (TOF) method. Young’s modulus is then calculated directly from the estimated C S. However, because shear waves in thin-layered media propagate as guided waves, C S cannot be accurately estimated using the conventional TOF method. Leaky Lamb dispersion analysis (LLDA) has recently been proposed to overcome this problem. In this study, we performed both experimental and finite-element (FE) analyses to evaluate the advantages of LLDA over TOF. In FE analysis, we investigated why the conventional TOF is ineffective for thin-layered media. In phantom experiments, C S results estimated using the two methods were compared for 1.5 and 2% agar plates and tube phantoms. Furthermore, it was shown that Lamb waves can be applied to tubular structures by extracting lateral waves traveling in the long axis direction of the tube using a two-dimensional window. Also, the effects of the inner radius and stiffness (or shear wavelength) of the tube on the estimation performance of LLDA were experimentally discussed. In phantom experiments, the results indicated good agreement between LLDA (plate phantoms of 2 mm thickness: 5.0 m/s for 1.5% agar and 7.2 m/s for 2% agar; tube phantoms with 2 mm thickness and 2 mm inner radius: 5.1 m/s for 1.5% agar and 7.0 m/s for 2% agar; tube phantoms with 2 mm thickness and 4 mm inner radius: 5.3 m/s for 1.5% agar and 7.3 m/s for 2% agar) and SWE measurements (bulk phantoms: 5.3 m/s ± 0.27 for 1.5% agar and 7.3 m/s ± 0.54 for 2% agar).

Ultrasonic guided wave tomography of pipes: A development of new techniques for the nondestructive evaluation of cylindrical geometries and guided wave multi-mode analysis

NASA Astrophysics Data System (ADS)

Leonard, Kevin Raymond

This dissertation concentrates on the development of two new tomographic techniques that enable wide-area inspection of pipe-like structures. By envisioning a pipe as a plate wrapped around upon itself, the previous Lamb Wave Tomography (LWT) techniques are adapted to cylindrical structures. Helical Ultrasound Tomography (HUT) uses Lamb-like guided wave modes transmitted and received by two circumferential arrays in a single crosshole geometry. Meridional Ultrasound Tomography (MUT) creates the same crosshole geometry with a linear array of transducers along the axis of the cylinder. However, even though these new scanning geometries are similar to plates, additional complexities arise because they are cylindrical structures. First, because it is a single crosshole geometry, the wave vector coverage is poorer than in the full LWT system. Second, since waves can travel in both directions around the circumference of the pipe, modes can also constructively and destructively interfere with each other. These complexities necessitate improved signal processing algorithms to produce accurate and unambiguous tomographic reconstructions. Consequently, this work also describes a new algorithm for improving the extraction of multi-mode arrivals from guided wave signals. Previous work has relied solely on the first arriving mode for the time-of-flight measurements. In order to improve the LWT, HUT and MUT systems reconstructions, improved signal processing methods are needed to extract information about the arrival times of the later arriving modes. Because each mode has different through-thickness displacement values, they are sensitive to different types of flaws, and the information gained from the multi-mode analysis improves understanding of the structural integrity of the inspected material. Both tomographic frequency compounding and mode sorting algorithms are introduced. It is also shown that each of these methods improve the reconstructed images both qualitatively and quantitatively.

Monitoring of surface-fatigue crack propagation in a welded steel angle structure using guided waves and principal component analysis

NASA Astrophysics Data System (ADS)

Lu, Mingyu; Qu, Yongwei; Lu, Ye; Ye, Lin; Zhou, Limin; Su, Zhongqing

2012-04-01

An experimental study is reported in this paper demonstrating monitoring of surface-fatigue crack propagation in a welded steel angle structure using Lamb waves generated by an active piezoceramic transducer (PZT) network which was freely surface-mounted for each PZT transducer to serve as either actuator or sensor. The fatigue crack was initiated and propagated in welding zone of a steel angle structure by three-point bending fatigue tests. Instead of directly comparing changes between a series of specific signal segments such as S0 and A0 wave modes scattered from fatigue crack tips, a variety of signal statistical parameters representing five different structural status obtained from marginal spectrum in Hilbert-huang transform (HHT), indicating energy progressive distribution along time period in the frequency domain including all wave modes of one wave signal were employed to classify and distinguish different structural conditions due to fatigue crack initiation and propagation with the combination of using principal component analysis (PCA). Results show that PCA based on marginal spectrum is effective and sensitive for monitoring the growth of fatigue crack although the received signals are extremely complicated due to wave scattered from weld, multi-boundaries, notch and fatigue crack. More importantly, this method indicates good potential for identification of integrity status of complicated structures which cause uncertain wave patterns and ambiguous sensor network arrangement.

Influence of alfalfa grazing-based feeding systems on carcass fat colour and meat quality of light lambs.

PubMed

Ripoll, G; Albertí, P; Joy, M

2012-02-01

One hundred and twenty-seven lambs were fed as follows: lambs and dams grazing alfalfa (Gr); the same as Gr but lambs had access to concentrate (Gr + S); ewes grazed and lambs received milk and concentrate until weaning and thereafter concentrate and straw (Rat-Gr); ewes and lambs were stall-fed (Ind). Lambs were slaughtered at 22-24 kg live weight and fat and M. rectus abdominis colour was measured instrumentally and subjectively. The evolution of the instrumental colour and texture of M. longissimus lumborum was also recorded. There were significant differences in the instrumental colour of subcutaneous fat amongst feeding systems, but no differences were observed upon visual appraisal. On average, M. rectus abdominis colour in the four feeding systems was classed as pink. Differences in longissimus thoracis colour at 0 h disappeared at 24h of air exposure and there were no differences in pH or cooking losses. At no time were any differences in instrumental texture found. Copyright © 2011 Elsevier Ltd. All rights reserved.

The Productivity of Male Thin-Tailed Lambs and Sheep Fed Complete Feed

NASA Astrophysics Data System (ADS)

Aluns, M. S.; Luthfi, N.

2018-02-01

The aim of this study is to examine the productivity of thin tailed lambs and sheep fed complete feed. The material used in this study were 6 thin tailed lambs aged ± 5 months with an average body weight of 15.41 ± 2.11 kg (CV 37.04%) and 6 thin tailed rams aged ± 1 year with an average body weight of 23, 01 ± 1.91 kg (CV 28.83%). The animals were raised intensively with complete feed as much as 3.5% of body weight. The feed contained 12% crude protein (CP) and 55% Total Digestible Nutrients (TDNs). The results showed that the average feed intake was 567.10 g DMI/d in lambs and 726.24 g DMI per day in sheep. An average of body gain of lambs was 0.02 kg/d and 0.01 kg/d. The day matter digestibility of lambs achieves 50.23% and 50.74% in sheep. Based on results, it can be inferred that lambs has same digestibility with sheep and has more efficient to be fattened than sheep.

Precision Saturated Absorption Spectroscopy of H3+

NASA Astrophysics Data System (ADS)

Guan, Yu-chan; Liao, Yi-Chieh; Chang, Yung-Hsiang; Peng, Jin-Long; Shy, Jow-Tsong

2016-06-01

In our previous work on the Lamb dips of the νb{2} fundamental band of H3+, the saturated absorption spectrum was obtained by the third-derivative spectroscopy using frequency modulation [1]. However, the frequency modulation also causes error in absolute frequency determination. To solve this problem, we have built an offset-locking system to lock the OPO pump frequency to an iodine-stabilized Nd:YAG laser. With this modification, we are able to scan the OPO idler frequency precisely and obtain the profile of the Lamb dips. Double modulation (amplitude modulation of the idler power and concentration modulation of the ion) is employed to subtract the interference fringes of the signal and increase the signal-to-noise ratio effectively. To Determine the absolute frequency of the idler wave, the pump wave is offset locked on the R(56) 32-0 a10 hyperfine component of 127I2, and the signal wave is locked on a GPS disciplined fiber optical frequency comb (OFC). All references and lock systems have absolute frequency accuracy better than 10 kHz. Here, we demonstrate its performance by measuring one transition of methane and sixteen transitions of H3+. This instrument could pave the way for the high-resolution spectroscopy of a variety of molecular ions. [1] H.-C. Chen, C.-Y. Hsiao, J.-L. Peng, T. Amano, and J.-T. Shy, Phys. Rev. Lett. 109, 263002 (2012).

Determination of lamb wave dispersion data in lossy anisotropic plates using time domain finite element analysis. Part I: theory and experimental verification.

PubMed

Hayward, Gordon; Hyslop, Jamie

2006-02-01

A theoretical and experimental approach for extraction of guided wave dispersion data in plate structures is described. Finite element modeling is used to calculate the surface displacement data (in-plane and out-of-plane) when the plate is subject to either symmetrical or antisymmetrical impulsive force stimulation at one or both of the parallel faces. Fourier transformation of the resultant space-time displacement histories is then employed to obtain phase velocity as a function of frequency. Experimental verification in the case of antisymmetrical stimulation is provided by means of a high-power Q-switched laser source that is used to excite guided waves in the plate. The subsequent out-of-plane displacement data were then obtained by means of a scanning laser vibrometer, and good agreement between theory and experiment is demonstrated. Examples of dispersion data are provided for aluminum, and excellent correlation between the data sets and conventional Rayleigh-Lamb theory for plate structures was obtained. This was then extended to lossy polymeric plates, in addition to both unpolarized and polarized piezoelectric ceramic plates, again with good agreement between the finite element modeling and optical experiments. The last set of results prepares the way for a detailed investigation of the nonhomogeneous piezoelectric composite waveguides described in a companion paper (Part II).

Breeding objectives for Targhee sheep.

PubMed

Borg, R C; Notter, D R; Kuehn, L A; Kott, R W

2007-11-01

Breeding objectives were developed for Targhee sheep under rangeland production conditions. Traits considered were those for which EPD were available from the US National Sheep Improvement Program and included direct and maternal effects on 120-d weaning weight (WW and MM, respectively); yearling weight (YW); yearling fleece weight, fiber diameter, and staple length; and percent lamb crop (PLC), measured as the number of lambs born per 100 ewes lambing. A bioeconomic model was used to predict the effects of a change of 1 additive SD in EPD for each trait, holding all other traits constant at their mean, on animal performance, feed requirements, feed costs, and economic returns. Resulting economic weightings were then used to derive selection indexes. Indexes were derived separately for 3 prolificacy levels (1.41, 1.55, and 1.70 lambs/ewe lambing), 2 triplet survival levels (50 and 67%), 2 lamb pricing policies (with or without discounting of prices for heavy feeder lambs), and 3 forage cost scenarios (renting pasture, purchasing hay, or reducing flock size to accommodate increased nutrient requirements for production). Increasing PLC generally had the largest impact on profitability, although an increase in WW was equally important, with low feed costs and no discounting of prices for heavy feeder lambs. Increases in PLC were recommended at all 3 prolificacy levels, but with low triplet survival the value of increasing PLC eventually declined as the mean litter size increased to approximately 2.15 lambs/ewe lambing and above. Increasing YW (independent of WW) increased ewe maintenance costs and reduced profitability. Predicted changes in breeding values for WW and YW under index selection varied with lamb pricing policy and feed costs. With low feed costs or no discounts for heavy lambs, YW increased at a modest rate in association with increasing WW, but with high feed costs or discounting of heavy lambs, genetic trends in WW were reduced by approximately 50% to constrain increases in YW. Changes in EPD for MM or fleece traits generally had smaller effects on profitability than changes in PLC, WW, and YW. Two indexes designed to address current rangeland production conditions (low forage costs and discounting of heavy feeder lambs) or more intensive and integrated production with retained ownership and value-based marketing of lambs (higher forage costs and no discounting of heavy lambs) were anticipated to meet the needs of most Targhee producers.

Analysis of coiled stator ultrasound motor: Fundamental study on analysis of wave propagation on acoustic waveguide for coiled stator

NASA Astrophysics Data System (ADS)

Ozeki, Seiya; Kurita, Keisuke; Uehara, Choyu; Nakane, Noriaki; Sato, Toshio; Takeuchi, Shinichi

2018-07-01

In our research group, we previously developed a coiled stator ultrasound motor (CS-USM) for medical applications such as intravascular ultrasound (IVUS) devices. However, wave propagation on acoustic waveguides has not been investigated sufficiently in previous studies. In this study, we analyze the propagation velocity of elastic waves from the simulated the vibration displacement mode profile along a straight line acoustic waveguide via three-dimensional finite element method (FEM). Concerning results, elastic waves with vibration displacement along the thickness direction show dispersion characteristics corresponding to the a0 and a1 mode plate waves (Lamb waves) in the acoustic waveguide. Our theoretical hypotheses of the propagation velocities were closely borne out by experimental results. We further find that the dispersion characteristic is affected by the width of the acoustic waveguide. We believe that our findings can contribute to improved CS-USM designs for practical application.

Effect of stress on ultrasonic pulses in fiber reinforced composites

NASA Technical Reports Server (NTRS)

Hemann, J. H.; Baaklini, G. Y.

1986-01-01

An acoustical-ultrasonic technique was used to demonstrate relationships existing between changes in attenuation of stress waves and tensile stress on an eight ply 0 degree graphite-epoxy fiber reinforced composite. All tests were conducted in the linear range of the material for which no mechanical or macroscopic damage was evident. Changes in attenuation were measured as a function of tensile stress in the frequency domain and in the time domain. Stress wave propagation in these specimens was dispersive, i.e., the wave speed depends on frequency. Wave speeds varied from 267,400 cm/sec to 680,000 cm/sec as the frequency of the signal was varied from 150 kHz to 1.9 MHz which strongly suggests that flexural/lamb wave modes of propagation exist. The magnitude of the attenuation changes depended strongly on tensile stress. It was further observed that the wave speeds increased slightly for all tested frequencies as the stress was increased.

Using guided ultrasonic wave inspection to quantify the length of delaminations in composite laminates

NASA Astrophysics Data System (ADS)

Feng, Bo; Ribeiro, Artur Lopes; Ramos, Helena Geirinhas

2018-04-01

This paper presents a study of the characteristics of Lamb wave (S0 mode) testing signals in carbon fiber composite laminates containing delaminations. The study was implemented by using commercial finite element simulation software - ANSYS. The delamination signal is proven to be the superposition of the two waves travelling from upper and lower sub-laminates. Dispersion curves for the two sub-laminates were calculated to show the difference between phase velocities of the waves in the sub-laminates. Two models are specifically designed to get the phase difference between the waves that travel in each of the two sub-laminates. From the simulation results, it was found that the phase difference increases with the delamination length. Furthermore, the amplitude of delamination signal decreases first, then it starts to increase after reaching the minimum value. The minimum is reached when the waves from the two sub-laminates are 180° out of phase.

Implementation of perfectly matched layers in an arbitrary geometrical boundary for elastic wave modelling

NASA Astrophysics Data System (ADS)

Gao, Hongwei; Zhang, Jianfeng

2008-09-01

The perfectly matched layer (PML) absorbing boundary condition is incorporated into an irregular-grid elastic-wave modelling scheme, thus resulting in an irregular-grid PML method. We develop the irregular-grid PML method using the local coordinate system based PML splitting equations and integral formulation of the PML equations. The irregular-grid PML method is implemented under a discretization of triangular grid cells, which has the ability to absorb incident waves in arbitrary directions. This allows the PML absorbing layer to be imposed along arbitrary geometrical boundaries. As a result, the computational domain can be constructed with smaller nodes, for instance, to represent the 2-D half-space by a semi-circle rather than a rectangle. By using a smooth artificial boundary, the irregular-grid PML method can also avoid the special treatments to the corners, which lead to complex computer implementations in the conventional PML method. We implement the irregular-grid PML method in both 2-D elastic isotropic and anisotropic media. The numerical simulations of a VTI lamb's problem, wave propagation in an isotropic elastic medium with curved surface and in a TTI medium demonstrate the good behaviour of the irregular-grid PML method.

Energy efficiency of growing ram lambs fed concentrate-based diets with different roughage sources.

PubMed

Galvani, D B; Pires, A V; Susin, I; Gouvêa, V N; Berndt, A; Chagas, L J; Dórea, J R R; Abdalla, A L; Tedeschi, L O

2014-01-01

Poor-quality roughages are widely used as fiber sources in concentrate-based diets for ruminants. Because roughage quality is associated with the efficiency of energy use in forage-based diets, the objective of this study was to determine whether differing the roughage source in concentrate-based diets could change the energy requirements of growing lambs. Eighty-four 1/2 Dorper × 1/2 Santa Inês ram lambs (18.0 ± 3.3 kg BW) were individually penned and divided into 2 groups according to primary source of dietary roughage: low-quality roughage (LQR; sugarcane bagasse) or medium-quality roughage (MQR; coastcross hay). Diets were formulated to be isonitrogenous (2.6% N) and to meet 20% of physically effective NDF. After a 10-d ad libitum adaptation period, 7 lambs from each group were randomly selected and slaughtered (baseline). Twenty-one lambs in each diet group were fed ad libitum and slaughtered at 25, 35, or 45 kg BW. The remaining 28 lambs (14 from each diet group) were submitted to 1 of 2 levels of feed restriction: 70% or 50% of the ad libitum intake. Retentions of body fat, N, and energy were determined. Additionally, 6 ram lambs (44.3 ± 5.6 kg BW) were kept in metabolic cages and used in a 6 × 6 Latin square experiment designed to establish the ME content of the 2 diets at the 3 levels of DM intake. There was no effect of intake level on diet ME content, but it was greater in the diet with LQR than in the diet with MQR (3.18 vs. 2.94 Mcal/kg, respectively; P < 0.01). Lambs fed the diet with LQR had greater body fat (g/kg of empty BW) and energy concentrations (kcal/kg of empty BW) because of a larger visceral fat deposition (P < 0.05). Using a low-quality roughage as a primary source of forage in a concentrate-based diet for growing lambs did not change NEm and the efficiency of ME use for maintenance, which averaged 71.6 kcal/kg(0.75) of shrunk BW and 0.63, respectively. On the other hand, the greater nonfibrous carbohydrate content of the diet with LQR resulted in a 17% better efficiency of ME use for gain (P < 0.01), which was associated with a greater partial efficiency of energy retention as fat (P < 0.01). This increased nutritional efficiency, however, should be viewed with caution because it is related to visceral fat deposition, a nonedible tissue.

Impact of rotational grazing on management of gastrointestinal nematodes in weaned lambs.

PubMed

Burke, J M; Miller, J E; Terrill, T H

2009-07-07

Gastrointestinal nematode (GIN) control for 'natural' or organic lamb production is needed, especially where Haemonchus contortus is prevalent. The objective was to determine the impact of rotational grazing on GIN infection of weaned lambs. In year 1, naturally infected Katahdin lambs (120 days of age) were randomly assigned to graze (1) continuous bermudagrass (CB; n=14), (2) rotational bermudagrass moved every 3.5 days and returned to original plot 35 days later for three rotations (RB; n=14), or (3) rotational bermudagrass rotated when forage height fell below 10 cm (RBH; n=7) where first day of grazing=Day 0. In late summer, all lambs were supplemented with 500 g corn/SBM because of poor condition. The following year, similar animals were used and included the CB (n=18) and the RB (n=36) groups only. In both years, fecal egg counts (FECs) and blood packed cell volume (PCV) were determined every 7-14 days and body weight every 28 days. Individuals were dewormed with 0.5 g copper oxide wire particles (COWP) when FAMACHA score increased to 3 or more. Between 0 and 3 deworming treatments per lamb were necessary and there tended to be fewer RB than CB lambs dewormed by Day 84 for both years combined (P<0.001). Worm free tracer lambs were introduced to CB (n=6) and RB (n=8) plots following the last rotation during the first year to determine worm burdens after 20 days of grazing. Abomasal worm burden tended to be greater in RB than CB or RBH tracer lambs (P<0.10), but intestinal worm numbers were similar. Differences may be due to differences in grazing patterns among groups. Body weight gains were similar between CB and RB groups. Economic value between the CB and RB lambs was similar based on number of lambs that could have been marketed as organic. For both years, lambs relied exclusively on COWP for GIN control with the exception of one lamb. In summary, while there was a reduced incidence of deworming in the RB compared with the CB group of lambs, estimated economic value of these systems was similar.

The impact of lambing stress on post-parturient behaviour of sheep with consequences on neonatal homeothermy and survival.

PubMed

Darwish, R A; Ashmawy, T A M

2011-10-01

During lambing the expression of an appropriate behavioural response from both the ewe and the lamb are extremely important to lamb survival. The aim of this study was to show the effect of length and difficulty of the birth process on the expression of maternal and neonatal behaviour with consequences on homeothermy and survival of the neonate lamb. Data were collected from 61 Finnish Landrace × Rahmani crossbred (second generation) primiparous ewes and their single born lambs. Based on the average length of parturition, the ewes were grouped into short birth (less than 32.5 min) and long birth (equal to or higher than 32.5 min) classes. The data recorded include maternal and neonatal behaviour, lamb body temperature over the first 3 days of life and survival rate of the neonate lamb during the first week after birth. Blood samples were also collected from the lamb, pre-suckling and at 24 and 72 h after birth. The obtained sera were assayed for thyroid hormones (T(3) and T(4)) that are associated with heat production. Ewes that had prolonged and difficult births did not show competent maternal behaviour compared to mothers with short and un-complicated deliveries, as they were slower to begin grooming their lambs after birth, spent less time licking their lambs, made less low-pitched vocalizations and nosing, were more likely to show rejection behaviour (10.34 % vs 5.4 %, P < 0.05), and were more likely to move away when the lamb sought the udder in an attempt to suck (acceptance rate, 55.5 % vs 64.79 %, P < 0.05). Similarly, lambs from a prolonged and difficult birth were significantly less vigorous after birth, as they had taken more time to stand, reach the udder and to suck successfully. These lambs had lower serum concentrations of T(3) and T(4), and they also had a reduced ability to maintain body temperature after birth. This effect persisted over the first 3 days of life and was associated with higher neonatal mortality in the first week after birth (11.54 %), compared to lambs from short and non-stressful birth processes (2.86 %, P < 0.01). From the present study, it can be concluded that, prolonged deliveries with birthing difficulty were one of the main causes of death of large, single-born lambs, as these complications cause the expression of inappropriate behavioural responses from both the ewe and neonatal lamb. Thus, interventions designed to reduce the incidence of prolonged parturitions are likely to be associated with better welfare for the ewe and the lamb and consequently improved lamb homeothermy and survival. Copyright © 2011 Elsevier Inc. All rights reserved.

Circulatory Responses to Asphyxia Differ if the Asphyxia Occurs In Utero or Ex Utero in Near-Term Lambs

PubMed Central

Sobotka, Kristina S.; Morley, Colin; Ong, Tracey; Polglase, Graeme R.; Aridas, James D. S.; Miller, Suzanne L.; Schmölzer, Georg M.; Klingenberg, Claus; Moss, Timothy J. M.; Jenkin, Graham; Hooper, Stuart B.

2014-01-01

Background A cornerstone of neonatal resuscitation teaching suggests that a rapid vagal-mediated bradycardia is one of the first signs of perinatal compromise. As this understanding is based primarily on fetal studies, we investigated whether the heart rate and blood pressure response to total asphyxia is influenced by whether the animal is in utero or ex utero. Methods Fetal sheep were instrumented at ∼139 days of gestation and then asphyxiated by umbilical cord occlusion until mean arterial blood pressure decreased to ∼20 mmHg. Lambs were either completely submerged in amniotic fluid (in utero; n = 8) throughout the asphyxia or were delivered and then remained ex utero (ex utero; n = 8) throughout the asphyxia. Heart rate and arterial blood pressure were continuously recorded. Results Heart rate was higher in ex utero lambs than in utero lambs. Heart rates in in utero lambs rapidly decreased, while heart rates in ex utero lambs initially increased following cord occlusion (for ∼1.5 min) before they started to decrease. Mean arterial pressure initially increased then decreased in both groups. Conclusions Heart rate response to asphyxia was markedly different depending upon whether the lamb was in utero or ex utero. This indicates that the cardiovascular responses to perinatal asphyxia are significantly influenced by the newborn's local environment. As such, based solely on heart rate, the stage and severity of a perinatal asphyxic event may not be as accurate as previously assumed. PMID:25393411

Circulatory responses to asphyxia differ if the asphyxia occurs in utero or ex utero in near-term lambs.

PubMed

Sobotka, Kristina S; Morley, Colin; Ong, Tracey; Polglase, Graeme R; Aridas, James D S; Miller, Suzanne L; Schmölzer, Georg M; Klingenberg, Claus; Moss, Timothy J M; Jenkin, Graham; Hooper, Stuart B

2014-01-01

A cornerstone of neonatal resuscitation teaching suggests that a rapid vagal-mediated bradycardia is one of the first signs of perinatal compromise. As this understanding is based primarily on fetal studies, we investigated whether the heart rate and blood pressure response to total asphyxia is influenced by whether the animal is in utero or ex utero. Fetal sheep were instrumented at ∼ 139 days of gestation and then asphyxiated by umbilical cord occlusion until mean arterial blood pressure decreased to ∼ 20 mmHg. Lambs were either completely submerged in amniotic fluid (in utero; n = 8) throughout the asphyxia or were delivered and then remained ex utero (ex utero; n = 8) throughout the asphyxia. Heart rate and arterial blood pressure were continuously recorded. Heart rate was higher in ex utero lambs than in utero lambs. Heart rates in in utero lambs rapidly decreased, while heart rates in ex utero lambs initially increased following cord occlusion (for ∼ 1.5 min) before they started to decrease. Mean arterial pressure initially increased then decreased in both groups. Heart rate response to asphyxia was markedly different depending upon whether the lamb was in utero or ex utero. This indicates that the cardiovascular responses to perinatal asphyxia are significantly influenced by the newborn's local environment. As such, based solely on heart rate, the stage and severity of a perinatal asphyxic event may not be as accurate as previously assumed.

Local numerical modelling of ultrasonic guided waves in linear and nonlinear media

NASA Astrophysics Data System (ADS)

Packo, Pawel; Radecki, Rafal; Kijanka, Piotr; Staszewski, Wieslaw J.; Uhl, Tadeusz; Leamy, Michael J.

2017-04-01

Nonlinear ultrasonic techniques provide improved damage sensitivity compared to linear approaches. The combination of attractive properties of guided waves, such as Lamb waves, with unique features of higher harmonic generation provides great potential for characterization of incipient damage, particularly in plate-like structures. Nonlinear ultrasonic structural health monitoring techniques use interrogation signals at frequencies other than the excitation frequency to detect changes in structural integrity. Signal processing techniques used in non-destructive evaluation are frequently supported by modeling and numerical simulations in order to facilitate problem solution. This paper discusses known and newly-developed local computational strategies for simulating elastic waves, and attempts characterization of their numerical properties in the context of linear and nonlinear media. A hybrid numerical approach combining advantages of the Local Interaction Simulation Approach (LISA) and Cellular Automata for Elastodynamics (CAFE) is proposed for unique treatment of arbitrary strain-stress relations. The iteration equations of the method are derived directly from physical principles employing stress and displacement continuity, leading to an accurate description of the propagation in arbitrarily complex media. Numerical analysis of guided wave propagation, based on the newly developed hybrid approach, is presented and discussed in the paper for linear and nonlinear media. Comparisons to Finite Elements (FE) are also discussed.

Differential response to an algae supplement high in DHA mediated by maternal periconceptional diet: intergenerational effects of n-6 fatty acids.

PubMed

Clayton, Edward H; Lamb, Tracy A; Refshauge, Gordon; Kerr, Matthew J; Bailes, Kristy L; Ponnampalam, Eric N; Friend, Michael A; Hopkins, David L

2014-08-01

Algae high in docosahexaenoic acid (DHA) may provide a source of long-chain omega-3 polyunsaturated fatty acids (LCn-3PUFA) for inclusion in the diet of lambs to improve the LCn-3PUFA status of meat. The effect of background LCn-3PUFA status on the metabolism of high DHA algae is, however, unknown. The aim of the current study was to determine whether the response to a high in DHA algae supplement fed to lambs for six weeks prior to slaughter was mediated by a maternal periconceptional diet. Forty Poll Dorset × Border Leicester × Merino weaner lambs were allocated to receive either a ration based on oat grain, lupin grain, and chopped lucerne (control) or the control ration with DHA-Gold™ algae included at 1.92 % DM (Algae) based on whether the dams of lambs had previously been fed a diet high in n-3 or n-6 around conception. LCn-3PUFA concentration was determined in plasma and red blood cells (RBC) prior to and following feeding. The concentrations of EPA and DHA in the plasma and RBC of lambs receiving the control ration were significantly (p < 0.001) lower when lambs received the ration for 14 days compared with pre-feeding concentrations. The concentrations of EPA and DHA were also significantly (p < 0.001) higher when lambs consumed the Algae ration compared with the control ration for 42 days. The increase in EPA and DHA was, however, significantly (p < 0.05) lower if lamb dams had previously been fed a diet high in n-6 at conception. Assessing the previous nutrition and n-3 status of lambs may allow producers to more accurately predict the likely response to supplements high in LCn-3PUFA, particularly, DHA.

Guided waves and defect scattering in metal matrix composite plates

NASA Technical Reports Server (NTRS)

Datta, Subhendu K.; Bratton, Robert L.; Shah, Arvind H.

1989-01-01

Guided Rayleigh-Lamb waves in a continuous graphite fiber reinforced magnesium plate has been studied. The interest in this material arises from its high thermal stability and because it provides high strength-to-weight ratio. Previous studies have shown that for wavelengths much larger than the fiber diameters and spacing, the material can be characterized as transversely isotropic with the symmetry axis aligned with the fiber direction. Because of the high longitudinal stiffness of the graphite fibers, the material shows strong anisotropy, with very high modulus in the fiber direction. For this reason, dispersion of guided waves is strongly influenced by the deviation of the direction of propagation from the symmetry axis. Results are given for propagation in different directions and for scattering of antiplane shear waves by surface-breaking cracks and delaminations.

Non-contact feature detection using ultrasonic Lamb waves

DOEpatents

Sinha, Dipen N [Los Alamos, NM

2011-06-28

Apparatus and method for non-contact ultrasonic detection of features on or within the walls of hollow pipes are described. An air-coupled, high-power ultrasonic transducer for generating guided waves in the pipe wall, and a high-sensitivity, air-coupled transducer for detecting these waves, are disposed at a distance apart and at chosen angle with respect to the surface of the pipe, either inside of or outside of the pipe. Measurements may be made in reflection or transmission modes depending on the relative position of the transducers and the pipe. Data are taken by sweeping the frequency of the incident ultrasonic waves, using a tracking narrow-band filter to reduce detected noise, and transforming the frequency domain data into the time domain using fast Fourier transformation, if required.

Mechanisms of resonant low frequency Raman scattering from metallic nanoparticle Lamb modes

NASA Astrophysics Data System (ADS)

Girard, A.; Lermé, J.; Gehan, H.; Margueritat, J.; Mermet, A.

2017-05-01

The low frequency Raman scattering from gold nanoparticle bimodal assemblies with controlled size distributions has been studied. Special care has been paid to determining the size dependence of the Raman intensity corresponding to the quadrupolar Lamb mode. Existing models based on a microscopic description of the scattering mechanism in small particles (bond polarizability, dipole induced dipole models) predict, for any Raman-active Lamb modes, an inelastic intensity scaling as the volume of the nanoparticle. Surprisingly experimental intensity ratios are found to be anomalously much greater than theoretical ones, calling into question this scaling law. To explain these discrepancies, a simple mechanism of Raman scattering, based on the density fluctuations in the nanoparticles induced by the Lamb modes, is introduced. This modeling, in which the nanoparticle is described as an elastic isotropic continuous medium—as in Lamb theory, successfully explains the major features exhibited by low frequency Raman modes. Moreover this model provides a unified picture for any material, suitable for handling both small and large size ranges, as well as non-resonant and resonant excitation conditions in the case of metallic species.

Noncontact measurement of guided ultrasonic wave scattering for fatigue crack characterization

NASA Astrophysics Data System (ADS)

Fromme, P.

2013-04-01

Fatigue cracks can develop in aerospace structures at locations of stress concentration such as fasteners. For the safe operation of the aircraft fatigue cracks need to be detected before reaching a critical length. Guided ultrasonic waves offer an efficient method for the detection and characterization of fatigue cracks in large aerospace structures. Noncontact excitation of guided waves was achieved using electromagnetic acoustic transducers (EMAT). The transducers were developed for the specific excitation of the A0 Lamb mode. Based on the induced eddy currents in the plate a simple theoretical model was developed and reasonably good agreement with the measurements was achieved. However, the detection sensitivity for fatigue cracks depends on the location and orientation of the crack relative to the measurement locations. Crack-like defects have a directionality pattern of the scattered field depending on the angle of the incident wave relative to the defect orientation and on the ratio of the characteristic defect size to wavelength. The detailed angular dependency of the guided wave field scattered at crack-like defects in plate structures has been measured using a noncontact laser interferometer. Good agreement with 3D Finite Element simulation predictions was achieved for machined part-through and through-thickness notches. The amplitude of the scattered wave was quantified for a variation of angle of the incident wave relative to the defect orientation and the defect depth. These results provide the basis for the defect characterization in aerospace structures using guided wave sensors.

Design and characterization of an ultrasonic lamb-wave power delivery system.

PubMed

Kural, Aleksander; Pullin, Rhys; Holford, Karen; Lees, Jonathan; Naylon, Jack; Paget, Christophe; Featherston, Carol

2013-06-01

In this paper, a novel design for an ultrasonic power transmission system designed for use in aircraft structural monitoring systems is described. The prototype system uses ultrasonic Lamb waves to carry energy along plates, such as those used in aircraft structures, and commercially available piezoelectric patch transducers as the transmitter and receiver. This sets it apart from other acoustic power transmission systems reported to date. The optimum configuration transmitted 12.7 mW of power across a distance of 54 cm in a 1.5-mm-thick aluminum plate, while being driven by a 20-Vpp, 35-kHz sinusoidal electric signal. This is in the same order of magnitude as the power required by the wireless sensors nodes of a structural health monitoring system currently being developed by Cardiff University and its partners. Thus, the power transmission system can be considered a viable component of the power source combination considered for the sensor nodes, which will also include vibration and thermal energy harvesting. The paper describes the design and optimization of the transmission and reception circuits with the use of inductive compensation. The use of laser vibrometry to characterize the transducers and to understand the signal propagation between them is also reported.

Thermo-acousto-photonics for noncontact temperature measurement in silicon wafer processing

NASA Astrophysics Data System (ADS)

Suh, Chii-Der S.; Rabroker, G. Andrew; Chona, Ravinder; Burger, Christian P.

1999-10-01

A non-contact thermometry technique has been developed to characterize the thermal state of silicon wafers during rapid thermal processing. Information on thermal variations is obtained from the dispersion relations of the propagating waveguide mode excited in wafers using a non-contact, broadband optical system referred to as Thermal Acousto- Photonics for Non-Destructive Evaluation. Variations of thermo-mechanical properties in silicon wafers are correlated to temperature changes by performing simultaneous time-frequency analyses on Lamb waveforms acquired with a fiber-tip interferometer sensor. Experimental Lamb wave data collected for cases ranging from room temperature to 400 degrees C is presented. The results show that the temporal progressions of all spectral elements found in the fundamental antisymmetric mode are strong functions of temperature. This particular attribute is exploited to achieve a thermal resolution superior to the +/- 5 degrees C attainable through current pyrometric techniques. By analyzing the temperature-dependent group velocity of a specific frequency component over the temperature range considered and then comparing the results to an analytical model developed for silicon wafers undergoing annealing, excellent agreement was obtained. Presented results demonstrate the feasibility of applying laser-induced stress waves as a temperature diagnostic during rapid thermal processing.

Use of a mixed sericea lespedeza and grass pasture system for control of gastrointestinal nematodes in lambs and kids.

PubMed

Burke, J M; Miller, J E; Mosjidis, J A; Terrill, T H

2012-05-25

Because of a high prevalence of anthelmintic resistance and consumer demand for chemical free meat products, management tools to minimize the need for deworming are needed. The objective was to examine the effectiveness of grazing sericea lespedeza (SL) in a mixed grass or a pure forage system for control of gastrointestinal nematodes (GIN); in other words pasture systems included grass, grass plus SL, or SL alone (Experiments 2 and 3). Selective use of copper oxide wire particles (COWP) based on the FAMACHA(©) system was used to aid in GIN control. In Experiment 1, lambs co-grazed bermudagrass (BG; n=21) or SL in a mixed grass pasture (SLM; n=22) with dams for 14 days. In Experiment 2, lambs grazed BG (n=14), SLM (n=13), or pure SL (SLP; n=13) pastures for 56 days. In Experiment 3, doe kids grazed BG (n=12), SLM (n=13), or SLP (n=13) for 84 days. Animals were fed a 16% crude protein supplement based on NRC requirements and estimated forage quality of pastures, so that 454, 389, and 200 g/lamb (Experiment 2), or 454, 300, and 150 g of supplement/goat (Experiment 3) was fed to BG, SLM, and SLP, respectively. Animals were dewormed with COWP if FAMACHA(©) was >3. Coprocultures were conducted to identify GIN genus. In Experiment 1, FEC were reduced in lambs grazing SLM compared with BG pastures. In Experiment 2, FEC were reduced in SLP compared with BG lambs on all days, and reduced in SLM compared with BG lambs on day 56. Initially, Haemonchus contortus was the predominant nematode, but the population shifted to other species in the SL groups by the end of the study. The mean number of dewormings/lamb was 0.71, 0.20, and 0.21±0.13 for BG, SLM, and SLP groups, respectively. In goats in Experiment 3, Trichostrongylus spp. was the predominant nematode in May and June and H. contortus in July. There was little meaningful effect of forage treatments on GIN infection in kids. Because H. contortus was not the predominant nematode in kids, the integrated approaches used may not have been effective in controlling GIN. Grazing SL was effective for GIN control in lambs in early summer, but the effect was delayed in lambs grazing a mixed SL/grass pasture unless lambs initially grazed with dams. An integrated approach used that included SL grazing and COWP for deworming was effective in lambs. Published by Elsevier B.V.

Baseline-free damage detection in composite plates based on the reciprocity principle

NASA Astrophysics Data System (ADS)

Huang, Liping; Zeng, Liang; Lin, Jing

2018-01-01

Lamb wave based damage detection techniques have been widely used in composite structures. In particular, these techniques usually rely on reference signals, which are significantly influenced by the operational and environmental conditions. To solve this issue, this paper presents a baseline-free damage inspection method based on the reciprocity principle. If a localized nonlinear scatterer exists along the wave path, the reciprocity breaks down. Through estimating the loss of reciprocity, the delamination could be detected. A reciprocity index (RI), which compares the discrepancy between the signal received in transducer B when emitting from transducer A and the signal received in A when the same source is located in B, is established to quantitatively analyze the reciprocity. Experimental results show that the RI value of a damaged path is much higher than that of a healthy path. In addition, the effects of the parameters of excitation signal (i.e., central frequency and bandwidth) and the position of delamination on the RI value are discussed. Furthermore, a RI based probabilistic imaging algorithm is proposed for detecting delamination damage of composite plates without reference signals. Finally, the effectiveness of this baseline-free damage detection method is validated by an experimental example.

Effect of thiamine concentration on animal health, feedlot performance, carcass characteristics, and ruminal hydrogen sulfide concentrations in lambs fed diets based on 60% distillers dried grains plus solubles.

PubMed

Neville, B W; Schauer, C S; Karges, K; Gibson, M L; Thompson, M M; Kirschten, L A; Dyer, N W; Berg, P T; Lardy, G P

2010-07-01

Limited data are available regarding the influence of thiamine supplementation on the incidence of polioencephalomalacia (PEM) in lambs fed diets containing increased concentrations of S in the diet (>0.7%). Therefore, our objective was to evaluate the influence of thiamine supplementation on feedlot performance, carcass quality, ruminal hydrogen sulfide gas concentrations, and incidence of PEM in lambs fed a finishing diet containing 60% distillers dried grains with solubles (DDGS; DM basis). Two studies were conducted using completely randomized designs to evaluate the influence of concentration of thiamine supplementation. Study 1 used 240 lambs fed in 16 pens, whereas study 2 used 55 individually fed lambs. Lamb finishing diets contained 60% DDGS, which resulted in a dietary S concentration of 0.73% (DM basis). Treatments diets were based on the amount of supplemental thiamine provided: 1) no supplemental thiamine (CON), 2) 50 mg/animal per day (LO), 3) 100 mg/animal per day (MED), or 4) 150 mg/animal per day (HI). Additionally, in study 2, a fifth treatment was included, which contained 0.87% S (DM basis; increased S provided by addition of dilute sulfuric acid) and provided 150 mg of thiamine/animal per day (HI+S). In study 1, ADG decreased quadratically (P = 0.04), with lambs fed the CON, LO, and MED diets gaining BW at a greater rate than lambs fed the HI diet. In study 1, DMI responded quadratically (P < 0.01), whereas G:F tended to differ linearly (P = 0.08) to concentration of thiamine supplementation, with MED lambs having greater DMI and decreased G:F. No differences (P > or = 0.17) in lamb performance were observed in study 2. In both studies, most carcass characteristics were unaffected, with the exception of a tendency for decreased carcass conformation (study 1; P = 0.09) and greater flank streaking (study 2; P = 0.03). No differences in ruminal hydrogen sulfide concentration (P > 0.05) among treatments were apparent until d 10, at which point lambs fed the LO diet had less hydrogen sulfide concentrations than all other treatments. Lambs fed HI had the greatest concentrations of hydrogen sulfide on d 31 (1.07 g of hydrogen sulfide /m(3); P < 0.009). Ruminal pH did not differ (P = 0.13) and averaged 5.6 +/- 0.06. No clinical cases of PEM were observed during the course of either study. The use of thiamine as a dietary additive to aid in the prevention of PEM in finishing lambs does not appear to be necessary under the conditions of this study.

Partial replacement of barley grain and soybean meal by fleabane (Conyza bonariensis) in diets of growing Awassi lambs.

PubMed

Abo Omar, J M; Omar, M

2012-07-01

Effects of partial substitution of barley grain and soybean meal with fleabane (FB) Conyza bonariensis on growth performances and body compositions of 24 male local Awassi lambs were studied. All lambs were male with an average BW of 20.3 kg (s.d. = 2.0 kg) at the beginning of the experiment. Animals were randomly divided into four groups of six lambs each. Lambs in each group received individually their cereal-soybean-based total mixed rations with levels of FB: 0, 50, 100 and 150 g/kg dry matter (DM) diet, which replaced similar values of barley and soybean meal. All rations were isonitrogenous and isocaloric. The fattening experiment lasted 9 weeks, after which all lambs were slaughtered. The composition of nutrients in the C. bonariensis were 89.6%, 15.0%, 28.0%, 30.0% and 10% for organic matter, CP, NDF, ADF and lignin, respectively. At the end of the experiment, lambs fed 100 and 150 g FB/kg DM diets gained more weight (P < 0.05) than those fed the control and 50 g FB/kg DM diets. The DM intake was lower in lambs fed the highest level of FB compared with intakes of lambs in other treatments. Diet content of FB had significant effect (P < 0.05) on weights of empty body, carcass, gut and external (hide, head and feet) among all animals. However, FB had no effects on lambs' thoracic organs (lungs and heart) and liver. Muscle, bone, omental and mesenteric fat, subcutaneous, intermuscular, pelvic and kidney fat weights (g/kg empty BW) were not affected by FB feeding. Carcass fat was decreased (P < 0.05) by the increase of FB. Total body fat was the same in all animals of the experiment.

An overview of the nutritional value of beef and lamb meat from South America.

PubMed

Cabrera, M C; Saadoun, A

2014-11-01

The southern region of South America, a subtropical and temperate zone, is an important region for the production of beef and lamb meat, which is mainly produced in extensive pasture-based systems. Because of its content in highly valuable nutrients such as iron, zinc, selenium, fatty acids, and vitamins, meat is a unique and necessary food for the human diet in order to secure a long and healthy life, without nutritional deficiencies. Beef and lamb production systems based on temperate or tropical grasslands show interesting and, in some cases, a differential content in minerals, fatty acids and vitamins. This review deals with the distinctive aspects of the nutritional quality of beef and lamb meat produced in this region in terms of nutritional composition and the bioavailability of key nutrients related to its contribution for a healthy diet for all ages. Copyright © 2014 Elsevier Ltd. All rights reserved.

On selection of primary modes for generation of strong internally resonant second harmonics in plate

NASA Astrophysics Data System (ADS)

Liu, Yang; Chillara, Vamshi Krishna; Lissenden, Cliff J.

2013-09-01

The selection of primary shear-horizontal (SH) and Rayleigh-Lamb (RL) ultrasonic wave modes that generate cumulative second harmonics in homogeneous isotropic plates is analyzed by theoretical modeling. Selection criteria include: internal resonance (synchronism and nonzero power flux), group velocity matching, and excitability/receivability. The power flux, group velocity matching, and excitability are tabulated for the SH and RL internal resonance points. The analysis indicates that SH waves can generate cumulative symmetric RL secondary wave fields. Laboratory experiments on aluminum plates demonstrate that excitation of the SH3 primary mode generates the s4 secondary RL mode and that the secondary wave field amplitude increases linearly with propagation distance. Simple magnetostrictive transducers were used to excite the primary SH wave and to receive the SH and RL wave signals. Reception of these wave modes having orthogonal polarizations was achieved by simply reorienting the electrical coil. The experiment was complicated by the presence of a nonplanar primary wavefront, however finite element simulations were able to clarify the experimental results.

THE HYPERFINE STRUCTURE OF THE ROTATIONAL SPECTRUM OF HDO AND ITS EXTENSION TO THE THz REGION: ACCURATE REST FREQUENCIES AND SPECTROSCOPIC PARAMETERS FOR ASTROPHYSICAL OBSERVATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cazzoli, Gabriele; Lattanzi, Valerio; Puzzarini, Cristina

2015-06-10

The rotational spectrum of the mono-deuterated isotopologue of water, HD{sup 16}O, has been investigated in the millimeter- and submillimeter-wave frequency regions, up to 1.6 THz. The Lamb-dip technique has been exploited to obtain sub-Doppler resolution and to resolve the hyperfine (hf) structure due to the deuterium and hydrogen nuclei, thus enabling the accurate determination of the corresponding hf parameters. Their experimental determination has been supported by high-level quantum-chemical calculations. The Lamb-dip measurements have been supplemented by Doppler-limited measurements (weak high-J and high-frequency transitions) in order to extend the predictive capability of the available spectroscopic constants. The possibility of resolving hfmore » splittings in astronomical spectra has been discussed.« less

Do Lambs Perceive Regular Human Stroking as Pleasant? Behavior and Heart Rate Variability Analyses

PubMed Central

Coulon, Marjorie; Nowak, Raymond; Peyrat, Julie; Chandèze, Hervé; Boissy, Alain; Boivin, Xavier

2015-01-01

Stroking by humans is beneficial to the human-animal relationship and improves welfare in many species that express intraspecific allogrooming, but very few studies have looked at species like sheep that do not express such contact except around parturition. This study investigated the way lambs perceive regular human tactile contact using behavioral and physiological responses. Twenty-four lambs were reared and bucket-fed in groups of four. All were stroked daily by their familiar caregiver. At 8 weeks of age, the lambs were individually tested in their home pen but in a 1×1m open-barred pen after a 15h period of habituation to physical separation from peers while remaining in visual and auditory contact. Half of the lambs received stroking by their caregiver for 8min and half were exposed to their caregiver’s immobile presence. Heart rate and heart rate variability were recorded and analyzed by 2-min slots over the same interval based on three measures: mean heart rate value (HR), root mean square of successive differences (RMSSD) and standard deviation of all intervals measured between consecutive sinus beats (SDNN). Behavioral responses (ear postures of the lamb and time spent in contact with the familiar caregiver, on the knees of the familiar caregiver, and moving) were recorded throughout the test. Lamb HR decreased continuously while in the presence of their caregiver. Lambs being stroked showed slower HR and higher RMSSD which reflected positive emotional states compared to lambs left unstroked. All behavioral variables were highly correlated with the main component axis of the PCA analyses: the more the animals stayed in contact with their caregiver, the less they moved and the more their ears were hanging. This first component clearly differentiates lambs being stroked or not. Behavioral and physiological observations support the hypothesis that gentle physical contact with the caregiver is perceived positively by lambs. PMID:25714604

Effects of feeding green forage of sulla (Hedysarum coronarium L.) on lamb growth and carcass and meat quality.

PubMed

Bonanno, A; Di Miceli, G; Di Grigoli, A; Frenda, A S; Tornambè, G; Giambalvo, D; Amato, G

2011-01-01

The nutritional effects of sulla (Hedysarum coronarium L.) forage containing condensed tannins (CT) on growth of lambs, and carcass and meat quality were investigated. Thirty-two male Comisana lambs aged 100 ± 8 days weighing 19.0 ± 2.8 kg were fed fresh forage of sulla or CT-free annual ryegrass (Lolium multiflorum Lam. subsp. Wersterwoldicum) for 49 days until slaughter; in addition, each lamb was supplied with 200 g/days of concentrate. Eight lambs per diet had been previously treated with anthelmintic drugs to remove nematode parasites. Measurements of BW and feed intake, and counts of faecal nematode eggs were made. Carcass parameters were recorded after slaughter, and tissue components of the hind leg were determined. Longissimus dorsi meat was evaluated for pH, colour, thawing and cooking losses, Warner-Bratzler shear force, chemical composition and sensory properties based on triangle tests. Relative to ryegrass-fed lambs, sulla-fed lambs had significantly greater dry matter (DM) and protein intake, a more favourable feed conversion ratio, and superior growth rate, final BW at 150 days of age, carcass weight, yield and fatness. These results were attributed to the high protein and non-structural carbohydrate content of sulla, and also to the moderate CT content of sulla (16.7 and 20.3 g/kg of DM in offered and consumed sulla forage, respectively). Anthelmintic treatment did not affect lamb growth, as the level of parasitic infection (initial and final) was low. The physical, chemical and sensory properties of the lamb meat were not influenced by diet.

Acoustic-gravity waves in atmospheric and oceanic waveguides.

PubMed

Godin, Oleg A

2012-08-01

A theory of guided propagation of sound in layered, moving fluids is extended to include acoustic-gravity waves (AGWs) in waveguides with piecewise continuous parameters. The orthogonality of AGW normal modes is established in moving and motionless media. A perturbation theory is developed to quantify the relative significance of the gravity and fluid compressibility as well as sensitivity of the normal modes to variations in sound speed, flow velocity, and density profiles and in boundary conditions. Phase and group speeds of the normal modes are found to have certain universal properties which are valid for waveguides with arbitrary stratification. The Lamb wave is shown to be the only AGW normal mode that can propagate without dispersion in a layered medium.

Inspection of helicopter rotor blades with the help of guided waves and "turning modes": Experimental and finite element analysis

NASA Astrophysics Data System (ADS)

Barnard, Daniel; Chakrapani, Sunil Kishore; Dayal, Vinay

2013-01-01

Modern helicopter rotor blades constructed of composite materials offer significant inspection challenges, particularly at inner structures, where geometry and differing material properties and anisotropy make placement of the probing energy difficult. This paper presents an application of Lamb waves to these structures, where mode conversion occurs at internal geometric discontinuities. These additional modes were found to successfully propagate to the targeted regions inside the rotor and back out, allowing evaluation of the structure. A finite element model was developed to simulate wave propagation and mode conversion in the structure and aid in identifying the signals received in the laboratory experiment. A good correlation between numerical and experimental results was observed.

Effect of feeding sorghum straw based complete rations with different roughage to concentrate ratio on dry matter intake, nutrient utilization, and nitrogen balance in Nellore ram lambs.

PubMed

Malisetty, Venkateswarlu; Yerradoddi, Ramana Reddy; Devanaboina, Nagalakshmi; Mallam, Mahender; Mitta, Pavani

2014-06-01

An experiment was conducted by feeding sorghum straw (Sorghum bicolor) based complete rations at roughage concentrate ratio 70:30 (CR-I), 60:40 (CR-II), 50:50 (CR-III), and 40:60 (CR-IV) for 180 days to find out suitable ratio of sorghum straw in the complete ration (mash form) on nutrient utilization and nitrogen balance in Nellore ram lambs. The DMI (g/day) increased significantly (P < 0.05) as level of concentrate increased in complete rations. No significant difference was found in digestibilities of proximate nutrients. However, CP digestibility was higher either significantly or nonsignificantly by 2.12, 5.50, and 9.36 %, respectively, in lambs fed with CR-II (P > 0.05), CR-III (P > 0.05), and CR-IV (P < 0.05) rations in comparison to lambs fed with CR-I ration. Furthermore, CP digestibility was higher by 7.09 and 3.66 % in lambs fed with CR-IV ration than those fed with CR-II (P < 0.05) and CR-III (P > 0.05) ration. The average CWC digestibility coefficients were comparable among four rations. The N intake (g/day) was significantly (P < 0.01) different and progressively increased by 31.46, 48.69, and 82.86 % in ram lambs fed with CR-II, CR-III, and CR-IV rations, respectively, in comparison to CR-I ration. The N balance (g/day) was higher either significantly or nonsignificantly by 34.46 (P > 0.05), 133.46 (P < 0.01), and 198.87 % (P < 0.01) with CR-II, CR-III, and CR-IV rations, respectively, in comparison to CR-I ration. Based on results, it is inferred that the level of sorghum straw in complete ration had no effect on digestibility of nutrients barring crude protein in Nellore ram lambs.

Effects of diet and Aspergillus oryzae extract or Saccharomyces cervisiae on growth and carcass characteristics of lambs and steers fed to meet requirements of natural markets.

PubMed

Zerby, H N; Bard, J L; Loerch, S C; Kuber, P S; Radunz, A E; Fluharty, F L

2011-07-01

Two studies were conducted to determine the effects of diet and feed additive on growth and carcass characteristics of lambs and cattle destined for all natural markets. In Exp. 1, 48 Dorset × Hampshire lambs (initial BW 29.4 ± 0.1 kg) were used in a randomized complete block experiment to determine the effects of Aspergillus oryzae extract, Amaferm (AMF) supplementation (1 g/d) in an 85% concentrate diet on growth and carcass characteristics. Lambs were allotted to 12 pens (4 lambs per pen), and blocked by sex and BW. Lambs were fed until the average BW of each pen reached a target BW (55.4 kg for wethers and 50.0 kg for ewes), at which time the entire pen of lambs was slaughtered. Amaferm resulted in a greater (P=0.07) G:F. In Exp. 2, 168 crossbred steers (initial BW 300 ± 0.7 kg) were used in a trial with a 3 × 2 factorial arrangement of treatments to examine the effects of 0.5 g/d of Saccaromyces cervisiae boulardii CNCM 1079-Levucell SB (LEV), or 3 g/d of AMF with 2 corn sources, dry whole-shelled corn or high moisture corn, on growth and carcass characteristics. Neither LEV nor AMF improved (P>0.10) carcass characteristics compared with control or non-feed-supplemented steers. Addition of LEV to high-concentrate, corn-based diets did not improve (P>0.10) growth performance of feedlot steers. However, addition of AMF to a diet composed of dry whole-shelled corn resulted in an improvement (P<0.05) in G:F (0.208 vs. 0.194). Results indicate that at the amounts fed, AMF may improve G:F for lambs and steers fed dry corn-based finishing diets. © 2011 American Society of Animal Science. All rights reserved.

Associations between lamb survival and prion protein genotype: analysis of data for ten sheep breeds in Great Britain

PubMed Central

Gubbins, Simon; Cook, Charlotte J; Hyder, Kieran; Boulton, Kay; Davis, Carol; Thomas, Eurion; Haresign, Will; Bishop, Stephen C; Villanueva, Beatriz; Eglin, Rachel D

2009-01-01

Background Selective breeding programmes, based on prion protein (PrP) genotype, have been introduced throughout the European Union to reduce the risk of sheep transmissible spongiform encephalopathies (TSEs). These programmes could have negative consequences on other important traits, such as fitness and production traits, if the PrP gene has pleiotropic effects or is in linkage disequilibrium with genes affecting these traits. This paper presents the results of an investigation into associations between lamb survival and PrP genotype in ten mainstream sheep breeds in Great Britain (GB). In addition, the reasons for lamb deaths were examined in order to identify any associations between these and PrP genotype. Results Survival times from birth to weaning were analysed for over 38000 lambs (2427 dead and 36096 live lambs) from 128 flocks using Cox proportional hazard models for each breed, including additive animal genetic effects. No significant associations between PrP genotype and lamb survival were identified, except in the Charollais breed for which there was a higher risk of mortality in lambs of the ARR/VRQ genotype compared with those of the ARR/ARR genotype. Significant effects of birth weight, litter size, sex, age of dam and year of birth on survival were also identified. For all breeds the reasons for death changed significantly with age; however, no significant associations between reason for death and PrP genotype were found for any of the breeds. Conclusion This study found no evidence to suggest that a selective breeding programme based on PrP genotype will have a detrimental effect on lamb survival. The only significant effect of PrP genotype identified was likely to be of little consequence because an increased risk of mortality was associated with a genotype that is selected against in current breeding strategies. PMID:19159456

Acousto-ultrasonics to Assess Material and Structural Properties

NASA Technical Reports Server (NTRS)

Kautz, Harold E.

2002-01-01

This report was created to serve as a manual for applying the Acousto-Ultrasonic NDE method, as practiced at NASA Glenn, to the study of materials and structures for a wide range of applications. Three state of the art acousto-ultrasonic (A-U) analysis parameters, ultrasonic decay (UD) rate, mean time (or skewing factor, "s"), and the centroid of the power spectrum, "f(sub c)," have been studied and applied at GRC for NDE interrogation of various materials and structures of aerospace interest. In addition to this, a unique application of Lamb wave analysis is shown. An appendix gives a brief overview of Lamb Wave analysis. This paper presents the analysis employed to calculate these parameters and the development and reasoning behind their use. It also discusses the planning of A-U measurements for materials and structures to be studied. Types of transducer coupling are discussed including contact and non-contact via laser and air. Experimental planning includes matching transducer frequency range to material and geometry of the specimen to be studied. The effect on results of initially zeroing the DC component of the ultrasonic waveform is compared with not doing so. A wide range of interrogation problems are addressed via the application of these analysis parameters to real specimens is shown for five cases: Case 1: Differences in density in [0] SiC/RBSN ceramic matrix composite. Case 2: Effect of tensile fatigue cycling in [+/-45] SiC/SiC ceramic matrix composite. Case 3: Detecting creep life, and failure, in Udimet 520 Nickel-Based Super Alloy. Case 4: Detecting Surface Layer Formation in T-650-35/PMR-15 Polymer Matrix Composites Panels due to Thermal Aging. Case 5: Detecting Spin Test Degradation in PMC Flywheels. Among these cases a wide range of materials and geometries are studied.

Comparison of the Microbial Quality of Lamb and Goat Meat Acquired from Internet and Local Retail Markets.

PubMed

Kim, Chyer; Stein, Roslyn A; Pao, Steven

2015-11-01

This study was conducted to evaluate the microbial quality of lamb and goat meat sold through local (Virginia) and Internet (U. S.) retail markets. A total of 134 frozen meat products consisting of locally purchased lamb ground (LLG) and lamb chops and Internet-procured lamb ground, goat ground, lamb chops (ILC), goat chops (IGC), lamb stew, and goat stew were tested. Significantly higher levels of aerobic mesophiles, psychrotrophs, and coliforms were found in the meat locally acquired than in the meat procured from the Internet. Similar average prevalence (27%) of Escherichia coli was observed regardless of market source. Ground meat had significantly high levels and prevalence of mesophiles, psychrotrophs, coliforms, and Listeria spp. One sample of LLG contained Campylobacter, and one sample of IGC contained Salmonella. Listeria spp. were present in 23 to 40% and 17 to 80% of samples from local and Internet markets, respectively. Pulsed-field gel electrophoresis (PFGE) of isolated E. coli strains revealed brand specificity and genomic diversity. No isolate from different brands and market sources had matching PFGE profiles. The average price of Internet meat ($23.4/kg) was about 1.2 times higher than the price of local meat, except for ILC, whose price was 2.7 times higher. This study revealed differences in microbial quality of lamb and goat meat based on market source; thus, meat products should be handled carefully regardless of market source because of the presence of high microbial levels and the high prevalence of pathogens.

Perinatal lamb mortality: an assessment of gross, histological and immunohistochemical changes in the central nervous system.

PubMed

Lashley, Vd; Roe, Wd; Kenyon, Pr; Thompson, Kg

2014-05-01

To compare the vascular and neuronal changes in the central nervous system (CNS) of lambs that died in the first 3 days after birth, from various causes, with control lambs subject to euthanasia. Dead lambs (n=65) were collected daily during the period 07 September 2010 to 26 September 2010 from a flock of 200 twin-lamb-bearing ewes. Age-matched lambs from the same flock were subject to euthanasia as a control group (n=39). Necropsies were conducted on all study lambs. The cause of death in lambs found dead was categorised as starvation-mismothering-exposure complex (SME), dystocia, or other, based on gross necropsy findings. Deaths were categorised as SME in lambs with necropsy lesions of pericardial, perirenal and mesenteric fat catabolism, an empty gastrointestinal tract and completely inflated lungs. Dystocia was diagnosed by the presence of a swollen tongue, injected sclera and subcutaneous oedema and haemorrhage around the head and neck or hind limbs. Deaths were categorised as other if an obvious cause of death could not be ascertained and if evidence of infection was identified. The CNS of each lamb necropsied was assessed grossly for haemorrhage, and using histopathology to determine vascular and neuronal changes. Immunohistochemistry was performed on selected cases (n=36) to confirm neuronal death. Of the 65 lambs found dead, 16 (25%) had evidence of cerebral and spinal meningeal haemorrhage, whereas of the 39 clinically normal control lambs, all displayed gross evidence of cerebral and spinal meningeal haemorrhage. There was no evidence of parenchymal vacuolation, neuronal vacuolation or ischaemic neurons in any of the lamb brain sections including those that died with evidence of dystocia. There was no difference, within the regions examined, in mean vascular score between lambs categorised by cause of death (p>0.05). The overall mean vascular score for the brain stem was greater than the mid brain (p=0.02) and the cortex (p=0.005) but did not differ from either the spinal cord or cerebellum (p>0.3). The vascular score for the spinal cord was greater than the mid brain (p=0.01) and cortex (p=0.003). Lambs that died of dystocia had less immunoreactivity for microtubule associated protein 2 (MAP2) in the hilus/CA4 region of the hippocampus (p=0.02) and dentate gyrus of the hippocampus (p=0.006) than those that were subject to euthanasia. Neither gross nor histological vascular changes in the CNS could be used to distinguish newborn lambs that had been subject to euthanasia from those that died with evidence of SME or dystocia, so meningeal haemorrhages in or on the brain and spinal cord of lambs that die in the neonatal period cannot be used to support a diagnosis of birth injury or dystocia. The CA4 region and the dentate gyrus of the hippocampus are useful regions for detecting hypoxic/ischaemic injury in lambs with evidence of dystocia. There was no evidence that hypoxia/ischaemia contributed to lambs dying of SME. The results of this study suggest that vascular changes in the CNS of newborn lambs may be produced artefactually. Caution is warranted with respect to interpretation of these vascular changes.

The power flow angle of acoustic waves in thin piezoelectric plates.

PubMed

Kuznetsova, Iren E; Zaitsev, Boris D; Teplykh, Andrei A; Joshi, Shrinivas G; Kuznetsova, Anastasia S

2008-09-01

The curves of slowness and power flow angle (PFA) of quasi-antisymmetric (A(0)) and quasi-symmetric (S(0)) Lamb waves as well as quasi-shear-horizontal (SH(0)) acoustic waves in thin plates of lithium niobate and potassium niobate of X-,Y-, and Z-cuts for various propagation directions and the influence of electrical shorting of one plate surface on these curves and PFA have been theoretically investigated. It has been found that the group velocity of such waves does not coincide with the phase velocity for the most directions of propagation. It has been also shown that S(0) and SH(0) wave are characterized by record high values of PFA and its change due to electrical shorting of the plate surface in comparison with surface and bulk acoustic waves in the same material. The most interesting results have been verified by experiment. As a whole, the results obtained may be useful for development of various devices for signal processing, for example, electrically controlled acoustic switchers.

The effect of stress on ultrasonic pulses in fiber reinforced composites

NASA Technical Reports Server (NTRS)

Hemann, J. H.; Baaklini, G. Y.

1983-01-01

An acoustical-ultrasonic technique was used to demonstrate relationships existing between changes in attenuation of stress waves and tensile stress for an eight ply 0 degree graphite-epoxy fiber reinforced composite. All tests were conducted in the linear range of the material for which no mechanical or macroscopic damage was evident. Changes in attenuation were measured as a function of tensile stress in the frequency domain and in the time domain. Stress wave propagation in these specimens was dispersive, i.e., the wave speed depends on frequency. Wave speeds varied from 267 400 cm/sec to 680 000 cm/sec as the frequency of the signal was varied from 150 kHz to 1.9 MHz which strongly suggests that flexural/lamb wave modes of propagation exist. The magnitude of the attenuation changes depended strongly on tensile stress. It was further observed that the wave speeds increased slightly for all tested frequencies as the stress was increased.

Growth performance, feed digestibility, body composition, and feeding behavior of high- and low-residual feed intake fat-tailed lambs under moderate feed restriction.

PubMed

Rajaei Sharifabadi, H; Naserian, A A; Valizadeh, R; Nassiry, M R; Bottje, W G; Redden, R R

2016-08-01

Two experiments were conducted to evaluate the effect of moderate feed restriction on productivity of lambs classified on the basis of phenotypic expression of residual feed intake (RFI). In Exp. 1, 58 fat-tailed Kurdi ram lambs (32.1 ± 4.2 kg BW) were individually fed, ad libitum, a pelleted diet (35% alfalfa hay and 65% concentrate). Feed intake and ADG were determined for a 6-wk period and 3 feed efficiency measures including RFI, G:F, and partial efficiency of maintenance (PEM) were calculated. The lambs were sorted based on RFI and the 16 highest RFI (RFI ≥ mean + 0.5 SD) and 16 lowest RFI (RFI ≤ mean - 0.5 SD) lambs were subjected to body composition (BC) and DM digestibility (DMD) analysis. Feeding behavior traits (FB) were also evaluated for 24 h using a regular 5-min interval observation method. The high- and low-RFI lambs (14 lambs/RFI group) so classified in Exp. 1 were used in Exp. 2. Half of the lambs in each RFI group were randomly selected to be fed ad libitum or 85% of ad libitum (restricted feeding), which resulted in 4 experimental groups: 1) ad libitum high-RFI, 2) feed restricted high-RFI, 3) ad libitum low-RFI, and 4) feed restricted low-RFI. The lambs were fed the same diet as Exp. 1, and growth efficiency during a 6-wk test period as well as BC, DMD, and FB were also determined in Exp. 2. In Exp. 1, the low-RFI lambs consumed 14% ( < 0.01) less feed than high-RFI lambs. Differences were also observed between high- and low-RFI groups for G:F ( = 0.01), RFI ( < 0.01), and PEM ( < 0.01) in Exp. 1, but no differences were detected between high- and low-RFI lambs for ADG ( = 0.79), DMD ( = 0.42), BC ( > 0.72), and FB ( > 0.24). In Exp.2, the restriction feeding regime negatively affected ADG ( < 0.01) and G:F ( = 0.02) in low-RFI lambs, whereas G:F ( = 0.02) and PEM ( < 0.01) were improved in high-RFI lambs under the feed restriction condition. No effects of feed restriction on DMD ( = 0.87) and BC ( > 0.05) were observed. The lambs fed at the restricted level of intake presented a greater time ( < 0.01) and rate ( = 0.01) of eating than those fed ad libitum. Although bunk visits and feeding events were decreased ( < 0.01) with feed restriction, no interaction ( > 0.05) was detected between RFI phenotype and feeding regime for FB. In summary, feeding high-RFI lambs at 85% of ad libitum level improved G:F with no effect on ADG, whereas growth performance was reduced by feeding low-RFI lambs at 85% of ad libitum. However, these changes in feed efficiency were not related to DMD, BC, or FB.

Last results of DIRAC experiment on study hadronic hydrogen-like atoms at PS CERN

NASA Astrophysics Data System (ADS)

Afanasyev, Leonid

2016-04-01

Results on study the hydrogen-like atoms consisting of charged pions and Kaons are presented. The first measurement of K+ π and Kπ+ atoms lifetime was fulfilled basing on identification of 178 ± 49 Kπ pairs from the atom breakup. The measured lifetime is τ = (2.5-1.8+3.0) fs. This value is dictated by properties of the strong πK-interaction at low energy, namely S-wave πK scattering length. The first experimental value of the isospin-odd combination of S-wave πK scattering length was obtained | a0- | =1/3 |a/2 -a3/2 | = (0.11-0.04+0.09) Mπ-1 (ai for isospin I). A dedicated experiment with π+ π atoms allows further study of these already observed atoms. The preliminary results on observation of the long-lived (metastable) states of π+ π atoms are presented. The observation of long-lived states opens the possibility to measure the energy difference between ns and np states - the Lamb shift.

Electromagnetic modulation of the ultrasonic signal for nondestructive detection of small defects and ferromagnetic inclusions in thin wall structures

NASA Astrophysics Data System (ADS)

Finkel, Peter

2008-03-01

We report on new nondestructive evaluation technique based on electromagnetic modulation of ultrasonic signal for detection of the small crack, flaws and inclusions in thin-walled parts. The electromagnetically induced high density current pulse produces stresses which alter the ultrasonic waves scanning the part with the defect and modulate ultrasonic signal. The excited electromagnetic field can produces crack-opening due to Lorentz forces that increase the ultrasonic reflection. The Joule heating associated with the high density current, and consequent thermal stresses may cause both crack-closure, as well as crack-opening, depending on various factors. Experimental data is presented here for the case of a small crack near holes in thin-walled structures. The measurements were taken at 2-10 MHz with a Lamb wave wedge transducer. It is shown that electromagnetic transient modulation of the ultrasonic echo pulse tone-burst suggest that this method could be used to enhance detection of small cracks and ferromagnetic inclusions in thin walled metallic structures.

SPECIAL ISSUE DEVOTED TO THE 80TH BIRTHDAY OF S.A. AKHMANOV: Three-wave interactions of surface defect-deformation waves and their manifestations in the self-organisation of nano- and microstructures in solids exposed to laser radiation

NASA Astrophysics Data System (ADS)

Emel'yanov, Vladimir I.; Seval'nev, D. M.

2009-07-01

The self-organisation of the surface-relief nanostructures in solids under the action of energy and particle fluxes is interpreted as the instability of defect-deformation (DD) gratings produced by quasi-static Lamb and Rayleigh waves and defect-concentration waves. The allowance for the nonlocality in the defects—lattice atom interaction with a simultaneous account for both (normal and longitudinal) defect-induced forces bending the surface layer leads to the appearance of two maxima in the dependence of the instability growth rate of DD waves on the wave number. Three-wave interactions of quasi-static coupled DD waves (second harmonic generation and wave vector mixing) are considered for the first time, which are similar to three-wave interactions in nonlinear optics and acoustics and lead to the enrichment of the spectrum of surface-relief harmonics. Computer processing of experimental data on laser-induced generation of micro- and nanostructures of the surface relief reveals the presence of effects responsible for the second harmonic generation and wave vector mixing.

Winter-feeding systems for gestating sheep II. Effects on feedlot performance, glucose tolerance, and carcass composition of lamb progeny.

PubMed

Radunz, A E; Fluharty, F L; Susin, I; Felix, T L; Zerby, H N; Loerch, S C

2011-02-01

Mature pregnant crossbred ewes (n = 90) were used in a randomized complete block design experiment and were assigned to 1 of 3 winter-feeding systems differing in primary feed source: haylage (HL), limit-fed corn (CN), or limit-fed dried distillers grains (DDGS). Effects of these winter-feeding strategies on postweaning progeny performance were determined. Lamb progeny (n = 96) were weaned at 61 ± 4 d of age and fed a common high-concentrate diet. Lambs were assigned to feedlot pen (n = 18) based on dam mid-gestation pen. Growth rate, DMI, and ADG were determined for the first 40 d of the finishing period. At 96 ± 4 d of age, 1 wether lamb was randomly selected from each pen (n = 18) for a glucose tolerance test. The experiment was terminated, and lambs were slaughtered individually when they were determined to have achieved 0.6-cm 12th-rib fat thickness. After a 24-h chill, carcass data were collected and a 2.54-cm chop was removed from each lamb from the LM posterior to the 12th rib for ether extract analysis. Additional carcass measurements of bone, muscle, and fat from the shoulder, rack, loin, and leg were collected on 35 carcasses. At weaning, lamb BW was not different among treatments, whereas final BW tended to be greater (P = 0.09) for lambs from ewes fed DDGS and CN during gestation than from those fed HL. Overall lamb growth rate from birth to slaughter was not different among treatments. Lambs from ewes fed DDGS vs. CN or HL tended to have a greater initial insulin response (P = 0.09). Dressing percent was less (P = 0.04) in lambs from ewes fed DDGS, but no difference (P = 0.16) was detected in HCW among treatments. As expected, 12th rib fat thickness was similar among treatments, whereas LM area was largest to smallest (P = 0.05) in lambs from ewes fed CN, HL, and DDGS, respectively. Proportion of internal fat tended to be greatest to smallest (P = 0.06) in lambs from ewes fed DDGS, CN, and HL, respectively. Calculated boneless trimmed retail cuts percentage was less (P = 0.04) in lambs from ewes fed DDGS than CN or HL. Loin muscle weight as a percentage of wholesale cut tended (P = 0.10) to be greater in lambs from ewes fed CN and HL than DDGS, whereas other muscle, bone, and fat weights and proportions were similar (P > 0.24) among treatments. Prepartum diet during mid to late gestation of ewes altered postnatal fat and muscle deposition and may be associated with alterations in insulin sensitivity of progeny.

Experimental evaluation of three leak detection and location concepts for space stations

NASA Technical Reports Server (NTRS)

Scherb, M. V.; Kazokas, G. P.; Zelik, J. A.; Mastandrea, J. R.; Mackallor, D. C.

1972-01-01

Three leak (or precursor damage modes) detection and location concepts for space station overboard leakage were evaluated experimentally. The techniques are: (1) static and dynamic seal leak detector sensing of moisture or all gases in space cabin atmosphere, (2) active ultrasonic Lamb-wave detection of flaws or cracks in cabin wall, and (3) impact gage detection of stress waves induced in cabin pressure wall by meteoroid or orbital impact. The experimental results obtained in the program demonstrated that all three leak detection and location concepts are feasible. With further development, the methods can be integrated into an effective damage control system for advanced manned earth-orbital systems.

Damage Assessment of Structures an Air Force Office of Scientific Research Structural Mechanics Perspective

DTIC Science & Technology

2007-07-01

air turbulence and structural vibration , etc. Flexible load- bearing skins and reconfigurable support structures for smart and adaptive morphing...phenomena for flapping-wing micro air vehicles, the prevention and control of nonlinear and aeroelastic phenomena, energy harvesting from environmental...Embedded Ultrasonic NDE is a research project aimed at studying the Lamb wave interaction between piezoelectric wafer active sensors (PWAS) and the host

United States Air Force 1987 Research Initiation Program

DTIC Science & Technology

1989-04-01

Composites for High-Temperature, Aerospace Applications 760-6MG-4I1 80 Synthesis of Compounds Capable of Dr. Robert Patsiga (1986) Intramolecular...Cyclization - Aromat- ization Reactions 760-6MG-065 81 Leaky Rayleigh and Lamb Waves on Dr. Nisar Shaikh (1986) Composites 760-6MG-007 82 Performance...measure meaningful physiochemical parameters. In order to ensure that the organic matter under investigation is indeed variable in both composition and

Peculiarities of energy trapping of the UHF elastic waves in diamond-based piezoelectric layered structure. I. Waveguide criterion.

PubMed

Kvashnin, G M; Sorokin, B P; Novoselov, A S

2018-03-01

Finite Element Modeling of the peculiarities of the trapping energy phenomenon in application to the piezoelectric layered structure (PLS) "Al/(0 0 1) AlN/Mo/(1 0 0) diamond" has been fulfilled. The resonant properties of longitudinal bulk acoustic waves (BAW) as well as frequency dependence of impedance within the 1 - 6 GHz band have been studied. The investigation of distribution of elastic energy flow and elastic displacements in a PLS cross-section allowed us to obtain an important information on energy trapping (ET) in PLS. Experimentally and as a result of modeling, it has been found that Q minimums are observed in PLS at quarter-wave resonance in the thin-film piezoelectric transducer (TFPT). Maximal Q value was observed at half-wave resonance in TFPT. It has been established that the ET-effect depends considerably on the mutual location of the n-th overtone's antiresonant frequency f a , n and cut-off frequencies of substrate f s , n-k- 1 and f s , n-k where f s , n-k- 1 f s , n-k , when the BAW energy excites the symmetrical or antisymmetrical Lamb waves. Copyright © 2017. Published by Elsevier B.V.

A Single Vaccination with an Improved Nonspreading Rift Valley Fever Virus Vaccine Provides Sterile Immunity in Lambs

PubMed Central

Oreshkova, Nadia; van Keulen, Lucien; Kant, Jet; Moormann, Rob J. M.; Kortekaas, Jeroen

2013-01-01

Rift Valley fever virus (RVFV) is an important pathogen that affects ruminants and humans. Recently we developed a vaccine based on nonspreading RVFV (NSR) and showed that a single vaccination with this vaccine protects lambs from viremia and clinical signs. However, low levels of viral RNA were detected in the blood of vaccinated lambs shortly after challenge infection. These low levels of virus, when present in a pregnant ewe, could potentially infect the highly susceptible fetus. We therefore aimed to further improve the efficacy of the NSR vaccine. Here we report the expression of Gn, the major immunogenic protein of the virus, from the NSR genome. The resulting NSR-Gn vaccine was shown to elicit superior CD8 and CD4-restricted memory responses and improved virus neutralization titers in mice. A dose titration study in lambs revealed that the highest vaccination dose of 106.3 TCID50/ml protected all lambs from clinical signs and viremia. The lambs developed neutralizing antibodies within three weeks after vaccination and no anamnestic responses were observed following challenge. The combined results suggest that sterile immunity was achieved by a single vaccination with the NSR-Gn vaccine. PMID:24167574

Guided Lamb wave based 2-D spiral phased array for structural health monitoring of thin panel structures

NASA Astrophysics Data System (ADS)

Yoo, Byungseok

2011-12-01

In almost all industries of mechanical, aerospace, and civil engineering fields, structural health monitoring (SHM) technology is essentially required for providing the reliable information of structural integrity of safety-critical structures, which can help reduce the risk of unexpected and sometimes catastrophic failures, and also offer cost-effective inspection and maintenance of the structures. State of the art SHM research on structural damage diagnosis is focused on developing global and real-time technologies to identify the existence, location, extent, and type of damage. In order to detect and monitor the structural damage in plate-like structures, SHM technology based on guided Lamb wave (GLW) interrogation is becoming more attractive due to its potential benefits such as large inspection area coverage in short time, simple inspection mechanism, and sensitivity to small damage. However, the GLW method has a few critical issues such as dispersion nature, mode conversion and separation, and multiple-mode existence. Phased array technique widely used in all aspects of civil, military, science, and medical industry fields may be employed to resolve the drawbacks of the GLW method. The GLW-based phased array approach is able to effectively examine and analyze complicated structural vibration responses in thin plate structures. Because the phased sensor array operates as a spatial filter for the GLW signals, the array signal processing method can enhance a desired signal component at a specific direction while eliminating other signal components from other directions. This dissertation presents the development, the experimental validation, and the damage detection applications of an innovative signal processing algorithm based on two-dimensional (2-D) spiral phased array in conjunction with the GLW interrogation technique. It starts with general backgrounds of SHM and the associated technology including the GLW interrogation method. Then, it is focused on the fundamentals of the GLW-based phased array approach and the development of an innovative signal processing algorithm associated with the 2-D spiral phased sensor array. The SHM approach based on array responses determined by the proposed phased array algorithm implementation is addressed. The experimental validation of the GLW-based 2-D spiral phased array technology and the associated damage detection applications to thin isotropic plate and anisotropic composite plate structures are presented.

Preferences for lamb meat: a choice experiment for Spanish consumers.

PubMed

Gracia, Azucena; de-Magistris, Tiziana

2013-10-01

This paper analyzes consumers' preferences for different lamb meat attributes using a choice experiment. In particular, preferences for the type of commercial lamb meat ("Ternasco" and "Suckling") and the origin of production (locally produced "Ojinegra from Teruel") were evaluated. Moreover, we endogenously identify consumers' segments based on consumers' preferences for the analyzed attributes. Data come from a survey administrated in Spain during 2009. A latent class model was used to estimate the effect of the attributes on consumer utility, derive the willingness to pay and determine consumers' segments. Results suggest that consumers' preferences for both attributes are heterogeneous and two homogenous consumers' segments were detected. The largest segment (79%) did not value any of the analyzed attributes while the smaller one (21%) valued both of them positively. In particular, consumers in this second segment are willing to pay an extra premium for the "Ternasco" lamb meat, around double the premium they are willing to pay for the locally produced lamb meat "Ojinegra from Teruel". Copyright © 2013 Elsevier Ltd. All rights reserved.

Ground Juniperus pinchotii and urea in supplements fed to Rambouillet ewe lambs: I. Feedlot growth traits, blood serum parameters, and fecal characteristics.

PubMed

Whitney, T R

2017-08-01

Ground woody products and urea are low-cost roughage and N sources. Rambouillet ewe lambs ( = 48, 6 lambs/treatment; initial BW = 42 kg ± 3.8) were used to evaluate effects of using ground (juniper) and urea in supplements on feedlot lamb growth traits, blood serum parameters, and fecal characteristics. In a randomized complete block design (40 d), lambs were individually fed an ad libitum basal sorghum-Sudangrass hay diet, which was fed separate from 1 of 8 supplemental diets (6 lambs/diet; 533 g of supplement/d, as-fed basis). Treatment structure was a 4 × 2 factorial: 4 concentrations of ground juniper (JN: 15%, 30%, 45%, or 60% of DM) and 2 concentrations of urea (UR: 1 or 3% of DM). Lamb growth traits were evaluated on d 0, 5, 12, 19, 26, 33, and 40; blood serum was evaluated on d 6 to 8, 20 to 22, and 34 (at h 3 and 6), and feces was evaluated on d 35. Compared to lambs fed all of the other treatments, lambs fed JN60UR1 or JN60UR3 had reduced supplement DMI (negative quadratic, = 0.007). Hay and total DMI were variable across day (JN × UR × day, < 0.04), but no linear or quadratic trends were detected ( > 0.10). A JN × day interaction was detected ( < 0.001) for lamb BW and the JN × day negative quadratic trend ( = 0.02) for BW was influenced by reduced ADG (linear decrease, < 0.001) of lambs fed JN60. Lambs supplemented with UR3 vs. UR1 tended ( = 0.06) to have reduced BW but had similar ( > 0.17) ADG and G:F. Lamb G:F fluctuated across day (JN × day, = 0.007), but the JN × day quadratic trend ( < 0.001) was mainly due to reduced G:F in lambs fed JN45 or JN60 diets. As the percentage of JN increased in the supplement, serum IGF-1 linearly decreased ( = 0.04), and serum urea N quadratically increased ( < 0.001). The UR × hour interaction ( < 0.001) for serum urea N resulted from a greater decline from 3 to 6 h after feeding in lambs supplemented with UR1 vs. UR3. Increasing JN concentration tended to quadratically increase ( = 0.09) fecal DM and linearly decrease ( = 0.002) fecal N, but an effect due to dietary UR was not detected ( > 0.34). Results indicated that daily supplement DMI was restricted only by using JN60. However, a 60% JN-based supplement will not make an effective rangeland supplement for growing ewe lambs, and using 3% UR should not be considered, especially since daily UR intake was not restricted enough to be considered safe.

Optimal sensor placement for active guided wave interrogation of complex metallic components

NASA Astrophysics Data System (ADS)

Coelho, Clyde K.; Kim, Seung Bum; Chattopadhyay, Aditi

2011-04-01

With research in structural health monitoring (SHM) moving towards increasingly complex structures for damage interrogation, the placement of sensors is becoming a key issue in the performance of the damage detection methodologies. For ultrasonic wave based approaches, this is especially important because of the sensitivity of the travelling Lamb waves to material properties, geometry and boundary conditions that may obscure the presence of damage if they are not taken into account during sensor placement. The framework proposed in this paper defines a sensing region for a pair of piezoelectric transducers in a pitch-catch damage detection approach by taking into account the material attenuation and probability of false alarm. Using information about the region interrogated by a sensoractuator pair, a simulated annealing optimization framework was implemented in order to place sensors on complex metallic geometries such that a selected minimum damage type and size could be detected with an acceptable probability of false alarm anywhere on the structure. This approach was demonstrated on a lug joint to detect a crack and on a large Naval SHM test bed and resulted in a placement of sensors that was able to interrogate all parts of the structure using the minimum number of transducers.

Bias of shear wave elasticity measurements in thin layer samples and a simple correction strategy.

PubMed

Mo, Jianqiang; Xu, Hao; Qiang, Bo; Giambini, Hugo; Kinnick, Randall; An, Kai-Nan; Chen, Shigao; Luo, Zongping

2016-01-01

Shear wave elastography (SWE) is an emerging technique for measuring biological tissue stiffness. However, the application of SWE in thin layer tissues is limited by bias due to the influence of geometry on measured shear wave speed. In this study, we investigated the bias of Young's modulus measured by SWE in thin layer gelatin-agar phantoms, and compared the result with finite element method and Lamb wave model simulation. The result indicated that the Young's modulus measured by SWE decreased continuously when the sample thickness decreased, and this effect was more significant for smaller thickness. We proposed a new empirical formula which can conveniently correct the bias without the need of using complicated mathematical modeling. In summary, we confirmed the nonlinear relation between thickness and Young's modulus measured by SWE in thin layer samples, and offered a simple and practical correction strategy which is convenient for clinicians to use.

Parameters influencing focalization spot in time reversal of acoustic waves

NASA Astrophysics Data System (ADS)

Zophoniasson, Harald; Bolzmacher, Christian; Hafez, Moustafa

2015-05-01

Time reversal is an approach that can be used to focus acoustic waves in a particular location on a surface, allowing a multitouch tactile feedback interaction. The spatial resolution in this case depends on several parameters, such as geometrical parameters, frequency used and material properties, described by the Lamb wave theory. This paper highlights the impact of frequency, geometrical parameters such as plate thickness and transducer's surface on the focused spot dimensions. In this paper a study of the influence of the plate's thickness and the frequency bandwidth used in the focusing process is presented. It is also shown that the dimension of the piezoelectric diaphragms used has little influence on the spatial resolution. Resonant behavior of the plate and its implication on focus point dimension and focalization contrast were investigated.

Rumen Bacteria Communities and Performances of Fattening Lambs with a Lower or Greater Subacute Ruminal Acidosis Risk

PubMed Central

Li, Fei; Wang, Zhilan; Dong, Chunxiao; Li, Fadi; Wang, Weimin; Yuan, Zehu; Mo, Futao; Weng, Xiuxiu

2017-01-01

Several ruminal cellulolytic bacteria species are sensitive to pH and could therefore be used as biomarkers to determine the risk of sub-acute ruminal acidosis (SARA) in finishing lambs. This study compared a 2–4 h post feeding ruminal pH measurement to abundances of the ruminal pH-sensitive bacteria to evaluate the risk of SARA in a herd of 120 finishing lambs. The lambs were reared in individual units for 50 days. Ruminal fluid was collected by use of an orogastric tube on day 51 2-4 h after feeding. Although the lambs were fed an identical diet, they responded differently in the abundances of four ruminal pH sensitive cellulolytic bacteria (Ruminococcus albus, Ruminococcus flavefaciens and Fibrobacter succinogenes and Butyrivibrio fibrisolvens). Lambs with the most or the least cellulolytic bacteria were then classified as either lower SARA risk (LSR, n = 10) or higher SARA risk group (HSR, n = 10), respectively. Data showed that the ruminal pH and VFA profiles were uncorrelated with the number of cellulolytic bacteria (P > 0.050). Lambs with the HSR showed lower ruminal pH (P = 0.013) and acetate to propionate ratio (P = 0.018), higher concentrations of lactate (P = 0.035) and proportion of propionate (P = 0.033) compared to those with the LSR. The DMI and ADG did not differ in LSR and HSR lambs (P > 0.050). A diversity analysis revealed significantly lower diversity in HSR lambs than in LSR (Simpson index, P = 0.004). The relative abundances of the phyla Bacteroidetes, Fibrobacteres, Verruomicrobia, and Proteobacteria were higher in LSR lambs than in HSR (P < 0.050). The abundances of several phyla including Firmicutes, Tenericutes and Actinobacteria were higher in the HSR than in the LSR group (P < 0.050). The bacterial communities of the LSR and HSR clustered separately in rumen based on the Unifrac distances, indicating distinct bacteria communities at OTU level between the LSR and HSR lambs. Overall, there was no correlation between 2 and 4 h post-feeding ruminal pH and the abundance of pH-sensitive bacteria and the amount of these bacteria could be used as a potential biomarker of SARA in lamb herd. PMID:29312208

Multiple-predators-based capture process on complex networks

NASA Astrophysics Data System (ADS)

Ramiz Sharafat, Rajput; Pu, Cunlai; Li, Jie; Chen, Rongbin; Xu, Zhongqi

2017-03-01

The predator/prey (capture) problem is a prototype of many network-related applications. We study the capture process on complex networks by considering multiple predators from multiple sources. In our model, some lions start from multiple sources simultaneously to capture the lamb by biased random walks, which are controlled with a free parameter $\\alpha$. We derive the distribution of the lamb's lifetime and the expected lifetime $\\left\\langle T\\right\\rangle $. Through simulation, we find that the expected lifetime drops substantially with the increasing number of lions. We also study how the underlying topological structure affects the capture process, and obtain that locating on small-degree nodes is better than large-degree nodes to prolong the lifetime of the lamb. Moreover, dense or homogeneous network structures are against the survival of the lamb.

Experimental Characterization of Guided Waves by Their Surface Displacement Vector Field

NASA Astrophysics Data System (ADS)

Barth, M.; Köhler, B.; Schubert, L.

2009-03-01

The development new nondestructive evaluation (NDE) and structural health monitoring (SHM) methods utilizing guided elastic waves needs a good understanding of wave propagation properties and the interaction of the waves with structures and defects. If the geometrical and stiffness properties of the components are well known, these effects can be studied very efficiently by numerical modeling. But very often there is a lack of precise knowledge of all necessary elastic properties; accurate and non-disturbing measurements are without alternative in these cases. The mapping of wave fields can be done by scanning laser vibrometers as demonstrated in a number of cases. Originally, a laser vibrometer provides only information from one displacement component. To get all three displacement components, the simultaneous measurement with three vibrometers is offered commercially. This is a very expensive approach. The paper describes a method which uses only one vibrometer sequentially for getting all three vector components. It allows determining additional parameters for characterizing wave modes as e.g. the ellipticity. The capability of this approach is demonstrated for the characterization of Lamb waves.

Index selection in terminal sires improves lamb performance at finishing.

PubMed

Márquez, G C; Haresign, W; Davies, M H; Roehe, R; Bünger, L; Simm, G; Lewis, R M

2013-01-01

Lamb meat is often perceived by consumers as fatty, and consumption has decreased in recent decades. A lean growth index was developed in the UK for terminal sire breeds to increase carcass lean content and constrain fat content at a constant age end point. The purposes of this study were 1) to evaluate the effects of index selection of terminal sires on their crossbred offspring at finishing and 2) to evaluate its effectiveness within terminal sire breeds. Approximately 70% of lambs marketed in the UK have been sired by rams of breeds typically thought of as specialized terminal sires. The most widely used are Charollais, Suffolk, and Texel. These breeds participated in sire referencing schemes from the early 1990s by sharing rams among flocks selected on the lean growth index. From 1999 to 2002 approximately 15 "high" and 15 "low" lean growth index score rams were selected from within their sire referencing schemes and mated to Welsh and Scottish Mule ewes. Their crossbred offspring were commercially reared on 3 farms in the UK. Lambs were finished to an estimated 11% subcutaneous fat by visual evaluation. At finishing, lambs were weighed, ultrasonically scanned, and assessed for condition score and conformation. Records were obtained for 6356 lambs on finishing BW (FWT), ultrasonic muscle depth (UMD), ultrasonic fat depth, overall condition score (OCS), and conformation of gigot, loin, and shoulder. Ultrasonic fat depth was log transformed (logUFD) to approach normality. High-index-sired lambs were heavier at finishing (1.2±0.2 kg) with thicker UMD (0.7±0.2 mm) and less logUFD (0.08±0.01 mm; P<0.05). There were no differences in OCS or conformation based on the sire index or breed (P>0.08). Suffolk-sired lambs were heavier than Charollais (1.0±0.3 kg), which were heavier than Texel (0.9±0.3 kg; P<0.001). Texel-sired lambs had thicker UMD than Charollais (0.7±0.2 mm; P<0.001) but were not different than Suffolk. Charollais-sired lambs had greater logUFD than both Texel (0.098±0.016 mm) and Suffolk (0.061±0.017 mm) sired lambs (P<0.001). Within a breed, high- and low-index-sired lambs differed in performance with the exceptions of FWT and UMD in Suffolks. Index selection produced heavier and leaner lambs at finishing. Producers have flexibility in choosing the terminal sire that best fits their production system.

Effects of dietary inclusion of sunflower soap stocks on nutrient digestibility, growth performance, and ruminal and blood metabolites of light fattening lambs.

PubMed

Blanco, C; Giráldez, F J; Prieto, N; Morán, L; Andrés, S; Benavides, J; Tejido, M L; Bodas, R

2014-09-01

Forty-four merino lambs (6 to 8 wk old; BW 15.6 ± 0.21 kg) were used to study the effect of adding different proportions of sunflower soap stock (SS) to pelleted total mixed ration (TMR) for fattening lambs on feed intake, animal growth and dressing percentage, ruminal fluid characteristics, and blood acid-base parameters. Lambs were assigned to 1 of 4 experimental groups (11 lambs per group), each randomly assigned to 1 dietary treatment: 00SS (0 g SS/kg TMR pellet), 15SS (15 g SS/kg TMR pellet), 30SS (30 g SS/kg TMR pellet), and 60SS (60 g SS/kg TMR pellet). Lambs were individually fed the corresponding diet ad libitum. On d 19 to 23, total feces were collected and sampled from 4 lambs per group. When lambs reached 27 kg BW, they were slaughtered. Dry matter intake, ADG, and length of fattening period were not affected by the dietary treatment (P > 0.10). Animals in the 30SS group tended to show the best G:F values (P < 0.10). Dressing percentage tended to linearly decrease as SS increased (P < 0.10). Animals in the 60SS groups showed the lowest DM and fiber digestibility values (P < 0.05). Total VFA contents in ruminal fluid were not affected (P > 0.10), but the propionate proportion linearly increased (P < 0.05), and the acetate to propionate ratio tended to decrease with SS supplementation. Increasing dietary content of SS linearly decreased the cold carcass weight (P < 0.05) but did not affect other measured carcass characteristics. Ruminal fluid pH tended to decrease (P < 0.10) and mucosa color decreased as SS increased in the TMR (P < 0.05). Blood pH and Na concentration increased (P < 0.05), whereas the anion gap, CO2 pressure, and K concentration linearly decreased (P < 0.05) as SS increased. Including more than 30 g SS/kg TMR in the diet for fattening lambs reduces DM and fiber digestibility without affecting feed intake and ADG. The acidotic rumen conditions that induced a darkening of rumen mucosa were counteracted by blood acid-base parameters. The optimum level of inclusion seems to be 30 g SS/kg TMR.

Guided waves propagating in sandwich structures made of anisotropic, viscoelastic, composite materials

NASA Astrophysics Data System (ADS)

Castaings, Michel; Hosten, Bernard

2003-05-01

The propagation of Lamb-like waves in sandwich plates made of anisotropic and viscoelastic material layers is studied. A semi-analytical model is described and used for predicting the dispersion curves (phase velocity, energy velocity, and complex wave-number) and the through-thickness distribution fields (displacement, stress, and energy flow). Guided modes propagating along a test-sandwich plate are shown to be quite different than classical Lamb modes, because this structure does not have the mirror symmetry, contrary to most of composite material plates. Moreover, the viscoelastic material properties imply complex roots of the dispersion equation to be found that lead to connections between some of the dispersion curves, meaning that some of the modes get coupled together. Gradual variation from zero to nominal values of the imaginary parts of the viscoelastic moduli shows that the mode coupling depends on the level of material viscoelasticity, except for one particular case where this phenomenon exists whether the medium is viscoelastic or not. The model is used to quantify the sensitivity of both the dispersion curves and the through-thickness mode shapes to the level of material viscoelasticity, and to physically explain the mode-coupling phenomenon. Finite element software is also used to confirm results obtained for the purely elastic structure. Finally, experiments are made using ultrasonic, air-coupled transducers for generating and detecting guided modes in the test-sandwich structure. The mode-coupling phenomenon is then confirmed, and the potential of the air-coupled system for developing single-sided, contactless, NDT applications of such structures is discussed.

16 CFR 301.8 - Use of terms “Persian Lamb,” “Broadtail Lamb,” and “Persian-broadtail Lamb” permitted.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Use of terms âPersian Lamb,â âBroadtail Lamb... Regulations § 301.8 Use of terms “Persian Lamb,” “Broadtail Lamb,” and “Persian-broadtail Lamb” permitted. (a) The term Persian Lamb may be used to describe the skin of the young lamb of the Karakul breed of sheep...

7 CFR 1280.111 - Lamb.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Lamb. 1280.111 Section 1280.111 Agriculture... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.111 Lamb. Lamb means...

A supplement containing multiple types of gluconeogenic substrates alters intake but not productivity of heat-stressed Afshari lambs.

PubMed

Mahjoubi, E; Amanlou, H; Hossein Yazdi, M; Aghaziarati, N; Noori, G R; Vahl, C I; Bradford, B J; Baumgard, L H

2016-06-01

Thirty-two Afshari lambs were used in a completely randomized design with a 2 × 2 factorial arrangement of treatments to evaluate a nutritional supplement designed to provide multiple gluconeogenic precursors during heat stress (HS). Lambs were housed in thermal neutral (TN) conditions and fed ad libitum for 8 d to obtain covariate data (period 1 [P1]) for the subsequent experimental period (period 2 [P2]). During P2, which lasted 9 d, half of the lambs were subjected to HS and the other 16 lambs were maintained in TN conditions but pair fed (PFTN) to the HS lambs. Half of the lambs in each thermal regime were fed (top-dressed) 100 g/d of a feed supplement designed to provide gluconeogenic precursors (8 lambs in HS [heat stress with Glukosa {HSG}] and 8 lambs in PFTN [pair-fed thermal neutral with Glukosa]) and the other lambs in both thermal regimes were fed only the basal control diet (HS without Glukosa [HSC] and pair-fed thermal neutral without Glukosa). Heat stress decreased DMI (14%) and by design there were no differences between the thermal treatments, but HSG lambs had increased DMI (7.5%; < 0.05) compared with the HSC lambs. Compared with PFTN lambs, rectal temperature and skin temperature at the rump, shoulder, and legs of HS lambs were increased ( < 0.05) at 0700 and 1400 h. Rectal temperature at 1400 h decreased for HSG lambs (0.15 ± 0.03°C; < 0.05) compared with HSC lambs. Despite similar DMI between thermal treatments, ADG for HS and PFTN lambs in P2 was decreased 55 and 85%, respectively, compared with lambs in P1 ( < 0.01). Although the prefeeding glucose concentration was not affected by thermal treatment or diet, HSG lambs had increased postfeeding glucose concentration compared with HSC lambs ( < 0.05). In contrast to the glucose responses, circulating insulin was influenced only by thermal treatment; HS lambs had increased insulin concentration ( < 0.01) before feeding and decreased concentration ( < 0.05) after feeding compared with PFTN lambs. Heat-stressed lambs had decreased NEFA concentration before feeding ( < 0.01) but not after feeding relative to PFTN lambs. Although this nutritional strategy did not affect ADG, the lower rectal temperature in HSG lambs indicates that dietary inclusion of a mixture of glucogenic precursors can potentially benefit animal health during HS.

7 CFR 1280.112 - Lamb products.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Lamb products. 1280.112 Section 1280.112 Agriculture... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.112 Lamb products. Lamb...

Lamb Wave Propagation in Varying Thermal Environments

DTIC Science & Technology

2007-03-01

detection in structural joints (5). The Tacoma Narrows Bridge collapse, which occurred on 7 November 1940, was due to a torsional or twisting mode that...operational, the airframes can be subjected to temperature swings (-40°F to 150°F) and the corrosive effects of salts, de-icing agents, and several types...aircraft-grade aluminum plate study was used to verify wavespeed dispersion characteristics (7:428). Techniques similar to these are implemented in the

A Feasibility Study into the Active Smart Patch Concept for Composite Bonded Repairs

DTIC Science & Technology

2008-08-01

electrical resistance foil gauges and PVDF (polyvinylidene) piezoelectric film to sense the local strain relaxation that occurs in re- sponse to failure of...structural components, like a wing skin, that are ‘thin’ in comparison to the wavelengths of low frequency ultrasound , and therefore act as efficient...region for the respective excitation frequency. The processed experimental data is compared to theoretical dispersion curves for both Lamb waves and

Lamb Wave Polarization Techniques for Structural Damage Localization and Quantification

DTIC Science & Technology

2011-11-01

11  Figure 11. Images showing (a) fatigued aluminum dog bone specimen with 53-mm crack and (b) 3-D SLDV test...Abaqus* and a 3-D model of a plate girder. Experimental measurements using piezoelectric ( PZT ) sensors were located on the web in pulse-echo mode, and...analyzed mode conversion of T- joint with collocated PZT sensors before and after the stiffener using a 2-D simulation under plane strain assumptions

Dispersion characteristics of the flexural wave assessed using low frequency (50-150kHz) point-contact transducers: A feasibility study on bone-mimicking phantoms.

PubMed

Kassou, Koussila; Remram, Youcef; Laugier, Pascal; Minonzio, Jean-Gabriel

2017-11-01

Guided waves-based techniques are currently under development for quantitative cortical bone assessment. However, the signal interpretation is challenging due to multiple mode overlapping. To overcome this limitation, dry point-contact transducers have been used at low frequencies for a selective excitation of the zeroth order anti-symmetric Lamb A0 mode, a mode whose dispersion characteristics can be used to infer the thickness of the waveguide. In this paper, our purpose was to extend the technique by combining a dry point-contact transducers approach to the SVD-enhanced 2-D Fourier transform in order to measure the dispersion characteristics of the flexural mode. The robustness of our approach is assessed on bone-mimicking phantoms covered or not with soft tissue-mimicking layer. Experiments were also performed on a bovine bone. Dispersion characteristics of measured modes were extracted using a SVD-based signal processing technique. The thickness was obtained by fitting a free plate model to experimental data. The results show that, in all studied cases, the estimated thickness values are in good agreement with the actual thickness values. From the results, we speculate that in vivo cortical thickness assessment by measuring the flexural wave using point-contact transducers is feasible. However, this assumption has to be confirmed by further in vivo studies. Copyright © 2017 Elsevier B.V. All rights reserved.

Comparison of parasitological and productive traits of Criollo lambs native to the central Mexican Plateau and Suffolk lambs experimentally infected with Haemonchus contortus.

PubMed

Alba-Hurtado, F; Romero-Escobedo, E; Muñoz-Guzmán, M A; Torres-Hernández, G; Becerril-Pérez, C M

2010-09-20

The study compares the parasitological and productive traits of Criollo lambs native to the central Mexican Plateau (CNCMP) and Suffolk (SU) lambs experimentally infected with Haemonchus contortus. CNCMP lambs (n=20) and SU lambs (n=15) were infected with L3 of H. contortus while five lambs of each genotype were kept as controls. Fecal egg count (FEC), packed cell volume (PCV), blood eosinophil number (BEN), ocular mucous membrane color (as measured by the FAMACHA index), changes in body condition score (BCS) and cumulative live weight gain (CLWG) were measured weekly during a 20-week period. On week 20, all animals were euthanized and the number of adult worms (AW) in the abomasum was counted. Infected SU lambs had higher (p<0.05) FEC and AW mean values compared to CNCMP lambs, which had a higher mean BEN count (p<0.05). Infected lambs had lower PCV values than controls, regardless of genotype, and had a negative correlation (r=-0.84, p<0.05) with the FAMACHA index. BCS tended to decline for infected SU lambs and increased slightly for infected CNCMP lambs. CLWG differed in all groups (p<0.05); infected SU lambs gained 12.1+/-1.9kg, infected CNCMP lambs gained 18.8+/-0.7kg, control SU lambs gained 34.6+/-1.6kg, and control CNCMP lambs gained 26.9+/-0.8kg. In conclusion, CNCMP lambs had a smaller worm burden, a better ability to maintain their productive traits, and were less affected by infection with Haemonchus contortus.

Omega-3 Long-Chain Fatty Acids in the Heart, Kidney, Liver and Plasma Metabolite Profiles of Australian Prime Lambs Supplemented with Pelleted Canola and Flaxseed Oils.

PubMed

Nguyen, Don V; Le, Van H; Nguyen, Quang V; Malau-Aduli, Bunmi S; Nichols, Peter D; Malau-Aduli, Aduli E O

2017-08-17

The objective of the study was to ascertain whether human health beneficial omega-3 long-chain (≥C 20 ) polyunsaturated fatty acid ( n -3 LC-PUFA) content in heart, kidney and liver can be enhanced by supplementing prime lambs with graded levels of canola and flaxseed oil. Health status of the lambs, as a consequence of the supplementation, was also investigated by examining their plasma metabolites. Sixty purebred and first-cross lambs were allocated to one of five treatments of lucerne hay basal diet supplemented with isocaloric and isonitrogenous wheat-based pellets without oil inclusion (Control) or graded levels of canola oil at 2.5% (2.5C), 5% (5C), flaxseed oil at 2.5% (2.5F) and 5% (5F) in a completely randomised design. Pre-slaughter blood, post-slaughter kidney, liver and heart samples were analysed for plasma metabolite and fatty acid profiles. Summations of docosapentaenoic acid and docosahexaenoic acid, and total n -3 LC-PUFA were enhanced in the liver and kidney of 5F supplemented lambs with a marked decrease in n -6/ n -3 ratio and significant breed differences detected. There were generally no deleterious impacts on animal health status. A combination of 5% oil supplementation and lamb genetics is an effective and strategic management tool for enhancing n -3 LC-PUFA contents of heart, kidney and liver without compromising lamb health.

Impact of changes in inspired oxygen and carbon dioxide on respiratory instability in the lamb.

PubMed

Wilkinson, Malcolm H; Sia, Kah-Ling; Skuza, Elizabeth M; Brodecky, Vojta; Berger, Philip J

2005-02-01

We examined the effect of hypoxia and hypercapnia administered during deliberately induced periodic breathing (PB) in seven lambs following posthyperventilation apnea. Based on our theoretical analysis, the sensitivity or loop gain (LG) of the respiratory control system of the lamb is directly proportional to the difference between alveolar PO2 and inspired PO2. This analysis indicates that during PB, when by necessity LG is >1, replacement of the inspired gas with one of reduced PO2 lowers LG; if we made inspired PO2 approximate alveolar PO2, we predict that LG would be approximately zero and breathing would promptly stabilize. In six lambs, we switched the inspired gas from an inspiratory oxygen fraction of 0.4 to one of 0.12 during an epoch of PB; PB was immediately suppressed, supporting the view that the peripheral chemoreceptors play a pivotal role in the genesis and control of unstable breathing in the lamb. In the six lambs in which we administered hypercapnic gas during PB, breathing instability was also suppressed, but only after a considerable time lag, indicating the CO2 effect is likely to have been mediated through the central chemoreceptors. When we simulated both interventions in a published model of the adult respiratory controller, PB was immediately suppressed by CO2 inhalation and exacerbated by inhalation of hypoxic gas. These fundamentally different responses in lambs and adult humans demonstrate that PB has differing underlying mechanisms in the two species.

Omega–3 Long-Chain Fatty Acids in the Heart, Kidney, Liver and Plasma Metabolite Profiles of Australian Prime Lambs Supplemented with Pelleted Canola and Flaxseed Oils

PubMed Central

Nguyen, Don V.; Le, Van H.; Nguyen, Quang V.; Malau-Aduli, Bunmi S.; Nichols, Peter D.

2017-01-01

The objective of the study was to ascertain whether human health beneficial omega–3 long-chain (≥C20) polyunsaturated fatty acid (n-3 LC-PUFA) content in heart, kidney and liver can be enhanced by supplementing prime lambs with graded levels of canola and flaxseed oil. Health status of the lambs, as a consequence of the supplementation, was also investigated by examining their plasma metabolites. Sixty purebred and first-cross lambs were allocated to one of five treatments of lucerne hay basal diet supplemented with isocaloric and isonitrogenous wheat-based pellets without oil inclusion (Control) or graded levels of canola oil at 2.5% (2.5C), 5% (5C), flaxseed oil at 2.5% (2.5F) and 5% (5F) in a completely randomised design. Pre-slaughter blood, post-slaughter kidney, liver and heart samples were analysed for plasma metabolite and fatty acid profiles. Summations of docosapentaenoic acid and docosahexaenoic acid, and total n-3 LC-PUFA were enhanced in the liver and kidney of 5F supplemented lambs with a marked decrease in n-6/n-3 ratio and significant breed differences detected. There were generally no deleterious impacts on animal health status. A combination of 5% oil supplementation and lamb genetics is an effective and strategic management tool for enhancing n-3 LC-PUFA contents of heart, kidney and liver without compromising lamb health. PMID:28817082

Effect of bitter vetch (Vicia ervilia) seeds as a replacement protein source of soybean meal on performance and carcass characteristics of finishing Awassi lambs.

PubMed

Abdullah, Abdullah Y; Muwalla, Marwan M; Qudsieh, Rasha I; Titi, Hosam H

2010-02-01

The objective of this study was to evaluate the effects of replacing the protein source of soybean meal (SBM) with different levels of bitter vetch seeds (BVS) in the diets of finishing Awassi ram lambs on performance, and carcass characteristics. Diets were designed based on replacing SBM with BVS as a percentage of the diet. Diets were: control (0% BVS), substituting 5% of SBM (5% BVS), 10% of SBM (10% BVS) and the entire SBM in the ration with BVS (15% BVS). Forty eight lambs (18.74 +/- 3.95 kg initial body weight and 70 days of age) were randomly assigned to 4 treatment diets (12 lambs/treatment). Lambs were given an adaptation period of 10 days and the experiment lasted for 84 days. At the end of the trial, a digestibility experiment was performed and 6 lambs from each treatment were slaughtered to evaluate carcass characteristics. Average daily gain tended (P = 0.07) to be higher for lambs fed 10% BVS when compared to the other diets. Neutral detergent fiber digestibility was higher (P < 0.01) in control diet compared to the other diets. Fat depth (C) and leg fat depth (L3) tended (0.05 < P < 0.1) to be affected by BVS levels in the diet. Leg total lean % was the highest (P < 0.05) in 5% BVS and 10% BVS diets. These results suggest that substituting SBM with BVS in the diets did not influence performance or carcass characteristics of lambs. However, the cost of ration formulation decreases since SBM is a very expensive component of the ration.

Efficacy and economic analysis of two treatment regimens using toltrazuril in lambs naturally infected with Eimeria spp. on pasture.

PubMed

de Souza Rodrigues, Fernando; Cezar, Alfredo Skrebsky; de Menezes, Fernanda Rezer; Sangioni, Luis Antônio; Vogel, Fernanda Silveira Flores; de Avila Botton, Sônia

2017-11-01

This study evaluated the efficacy and the economic viability of two anticoccidial treatment regimens tested in lambs naturally exposed to Eimeria spp. re-infections in a grazing system during a 140-day period. Twenty-four suckling lambs were distributed into three groups based on the individual count of oocysts per gram of feces (OPG) and body weight. Animals were treated with toltrazuril 5% (20 mg/kg) at 14- (GI) or 21-day (GII) intervals, and GIII was kept as untreated control. A cost-benefit analysis of each treatment regimen was calculated. Additionally, economic analysis was performed on four hypothetical scenarios, in which lambs could be having 10, 25, 50, or 85% decrease in their expected body weight gain due to clinical. Efficacy of toltrazuril against Eimeria spp. was 96.9-99.9% (GI) and 74.2-99.9% (GII). E. ovinoidalis was most frequently identified, but no clinical signs of coccidiosis were observed in lambs. There were no differences in weight gain among the groups. The cost of treatment per lamb was $13.09 (GI) and $7.83 (GII). The estimation model showed that the cost-benefit ratio favored treatment with toltrazuril when lambs fail to gain weight. In the studied flock, the break-even point for toltrazuril administered at 14-day intervals was reached with 85% decrease in mean weight gain. In conclusion, toltrazuril can be used at 14-day intervals to control Eimeria spp. (re)-infection in lambs raised on pasture. This treatment regimen was not economically feasible for subclinical coccidiosis; however, it may be feasible when used to prevent weight loss caused by clinical coccidiosis.

The effect of sainfoin (Onobrychis viciifolia) and carob pods (Ceratonia siliqua) feeding regimes on the control of lamb coccidiosis.

PubMed

Saratsis, A; Voutzourakis, N; Theodosiou, T; Stefanakis, A; Sotiraki, S

2016-06-01

Recent research has suggested that plants containing condensed tannins may offer a promising alternative approach for the control of coccidiosis in lambs and goat kids. The present study aimed to examine the potential effect of condensed tannins in sainfoin (Onobrychis viciifolia) and carob pods (Ceratonia siliqua) incorporated in sheep rations against lamb coccidiosis. The above tannin-rich sources were studied in three independent feeding trials in which the animals (naturally infected by Eimeria spp. ewes and their lambs) were allocated (i) in the control group and received a tannin-free diet (lucerne hay), or (ii) in the treatment groups and received a tannin-rich diet based on sainfoin hay (in trials 1 and 2), or in carob pod meal and a combination of carob pod meal and sainfoin hay (in trial 3). In total, 95 newborn lambs (and their 73 ewes) were enrolled in all trials which started a month before lambing and ended 8-10 weeks after lambs were born (at weaning). The course of coccidial infection was monitored in lambs by faecal oocyst counts and consistencies which were recorded at weekly intervals. Moreover, lambs total weight gain was evaluated at the end of each trial. During all trials, 100 % of the animals got naturally infected by Eimeria species and the infection burden was higher in trials 2 and 3 compared to trial 1 but in all cases, severe signs of diarrhoea were not observed. Tannin-rich diets were well accepted by the animals not affecting their feed intake and body weight gain when compared to the controls. The results suggest that incorporation of both tannin-rich resources (especially sainfoin) in sheep rations can reduce Eimeria oocyst excretion rates by the lambs, which can decrease subsequently the contamination of the farm environment with the parasite. However, the high variability noted on the results is not allowing us to draw any definite conclusions at least until the potential of those plants is further investigated.

Characteristics of lambs fed concentrates or grazed on ryegrass to traditional or heavy slaughter weights. II. Wholesale cuts and tissue accretion.

PubMed

Borton, R J; Loerch, S C; McClure, K E; Wulf, D M

2005-06-01

Targhee x Hampshire lambs (average BW 24 +/- 1 kg) were used to determine the effect of finishing on concentrate or by grazing ryegrass forage on slaughter weights of 52 kg (N) or 77 kg (H) on tissue accretion and lamb wholesale cutout. When fed to similar slaughter weights, the wholesale cuts of concentrate-fed lambs were heavier (P < 0.05) than the same cuts from forage-fed lambs; however, when expressed as a percentage of side weight, carcasses of forage-fed lambs had a higher (P < 0.001) percentage of leg than concentrate-fed lambs. Increasing slaughter weight from 52 to 77 kg resulted in a 1-kg increase in loin weight for lambs finished on concentrate and a 0.60-kg increase for lambs finished on forage (diet x slaughter weight, P < 0.03); however, the increased loin weight for lambs finished on concentrate was due largely to increased fat deposition. For lambs slaughtered at 77 kg, those finished on forage had more lean mass in the leg, loin, rack, and shoulder than those finished on concentrate, but lean mass in these cuts did not differ between diets for lambs slaughtered at 52 kg (diet x slaughter weight, P < 0.01). At the normal slaughter weight (52 kg), concentrate-fed lambs had 50% more dissectible fat than forage-fed lambs, whereas at the heavy slaughter weight, a 79% greater amount of dissectible fat was observed for concentrate- vs. forage-fed lambs (diet x slaughter weight, P < 0.001). Lean and fat accretion rates were higher (P < 0.001) for concentrate-fed lambs than for forage-fed lambs. The lean-to-fat ratio of forage-fed lambs was higher (P < 0.001) than that of concentrate-fed lambs; however, forage finishing decreased accretion rates of all tissues compared with concentrate feeding, and these differences between forage and concentrate feeding were magnified at heavier slaughter weights.

Classical natural ovine scrapie prions are detected in practical volumes of blood by lamb and transgenic mouse bioassay

USDA-ARS?s Scientific Manuscript database

In vitro ligand-based immunoassay studies revealed abnormal isoforms of prion protein (PrP-Sc) are primarily associated with B lymphocytes of scrapie-infected sheep. Our recent study also demonstrated efficient transmission of scrapie to lambs following a transfusion of B lymphocytes isolated from 5...

Ewe's diet (pasture vs grain-based feed) affects volatile profile of cooked meat from light lamb.

PubMed

Almela, Elisabeth; Jordán, María José; Martínez, Cristina; Sotomayor, José Antonio; Bedia, Mario; Bañón, Sancho

2010-09-08

The effects of ewe's diet during gestation and lactation on the volatile compounds profile in cooked meat from light lamb were compared. Two lamb groups from ewes that had been fed pasture (PA) or grain-based concentrate (FE) were tested. Cooked loin mixed with saliva was analyzed by solid phase microextraction, gas chromatography, and mass spectrometry. The fiber coating used was divinylbenzene-carboxen-polydimethylsiloxane. The volatiles detected and quantified were aldehydes, alcohols, ketones, phenols, indole, and sulfur compounds. The ewe's diet strongly affected the volatile compounds profile of the cooked meat. The total volatiles concentration was higher in PA (409 mg kg(-1)) than in FE (201 mg kg(-1)). The major volatiles in PA were phenol, 4-methylphenol, and hexanoic acid, while the major volatile in FE was 3-hydroxy-2-butanone. No branched C8-C9 fatty acids responsible for mutton flavor were detected in either group. The findings suggest that nutritional strategies can be use during gestation and lactation to modify the aroma of light lamb meat in the light of consumer preferences.

Influence of diets with silage from forage plants adapted to the semi-arid conditions on lamb quality and sensory attributes.

PubMed

Campos, F S; Carvalho, G G P; Santos, E M; Araújo, G G L; Gois, G C; Rebouças, R A; Leão, A G; Santos, S A; Oliveira, J S; Leite, L C; Araújo, M L G M L; Cirne, L G A; Silva, R R; Carvalho, B M A

2017-02-01

Quality and sensory attributes of meat from 32 mixed-breed Santa Inês lambs fed diets composed of four silages with old man saltbush (Atriplex nummularia Lind), buffelgrass (Cenchrus ciliaris), Gliricidia (Gliricidia sepium), and Pornunça (Manihot sp.) were evaluated. Meat from lambs fed diet containing old man saltbush silage (P<0.05) showed greater values for cooking loss. Of the sensory attributes evaluated in the Longissimus lumborum muscle of the lambs, color and juiciness did not differ (P>0.05). However, the silages led to differences (P<0.05) in aroma, tenderness, and flavor values. The meat from animals fed the pornunça and Gliricidia silages was tenderer. Flavor scores were higher in meat from lambs that consumed old man saltbush silage and lower in the meat from those fed buffelgrass silage. Diets formulated with buffelgrass silage for sheep reduce meat production. Based on the results for carcass weight and meat quality, old man saltbush and pornunça are better silages for finishing sheep. Copyright © 2016 Elsevier Ltd. All rights reserved.

Humoral and cellular immunity in chromium picolinate-supplemented lambs.

PubMed

Dallago, B S L; McManus, C M; Caldeira, D F; Campeche, A; Burtet, R T; Paim, T P; Gomes, E F; Branquinho, R P; Braz, S V; Louvandini, H

2013-08-01

The effects of oral supplementation of chromium picolinate (CrPic) on humoral and cellular immunity in sheep were investigated. Twenty-four male lambs divided into four treatments and received different dosages of CrPic: placebo (0), 0.250, 0.375, and 0.500 mg of chromium/animal/day during 84 days. The base ration was Panicum maximum cv Massai hay and concentrate. Blood samples were collected fortnightly for total and differential leukocyte counts. On days 28 and 56, the lambs were challenged with chicken ovalbumin I.M. Serum samples were collected on days 46 and 74 and subjected to an indirect enzyme-linked immunosorbent assay to measure IgG anti-ovalbumin. The cell-mediated immune response was determined by a delay-type hypersensitivity test using phytohemagglutinin. CrPic did not significantly affect humoral immunity in lambs but there was a negative effect on cellular immunity (P < 0.05) as Cr supplementation increased. Therefore, the level of Cr supplementation for lambs must be better studied to address its effect on stressed animals or the possible toxic effects of Cr on the animal itself or its immune system.

Influence of quality labels on the formation of preferences of lamb meat consumers. A Spanish case study.

PubMed

Bernabéu, Rodolfo; Rabadán, Adrián; El Orche, Nour E; Díaz, Mónica

2018-01-01

Analysis of the attributes determining the formation of consumers' preferences when buying lamb meat is a key aspect in increasing the demand for this product. To this end, by means of conjoint analysis, we determined lamb meat consumers' preferences according to their frequency of consumption, and we used logistic simulation to analyse market shares of the most valued attributes. After segmenting the market into habitual and occasional consumers of lamb meat, our results seem to suggest that while regular consumers base their preferences mostly on origin, occasional consumers take other attributes into account, such as Protected Geographical Origin (PGI) and organic production. An analysis of market shares shows that PGI significantly influences consumer preferences, while ecological production has a less marked impact. This finding confirms the usefulness of PGI in the lamb meat market and highlights the urgent need to improve the communication strategy of the organic production sector as a synergistic effect to increase its acceptance among consumers. Copyright © 2017 Elsevier Ltd. All rights reserved.

Management of maternal-offspring behavior to improve lamb survival in easy care sheep systems.

PubMed

Everett-Hincks, J M; Dodds, K G

2008-04-01

This paper examines the environmental and management factors affecting lamb survival on high-performing sheep farms in New Zealand. Improved lambing percentage is the biggest contributor to higher profits on New Zealand sheep farms. Many sheep breeders have selected and bred ewes for increased fecundity over the last 4 decades. The increased proportion of ewes having triplets is of concern to farmers and to industry because neonatal lamb mortality is highest in triplets. The majority of lamb deaths occur in the first 3 d after birth and range from 5 to 30% for individual sheep flocks. The ability of a lamb to survive to weaning is determined by genetics, behavior, physiology, and the environment, including on-farm management practices. We investigated the effects of dam body condition in pregnancy, weather during lambing, lamb birth weight, and maternal behavior on single, twin, and triplet lamb viability at birth, lamb death risks from dystocia, and starvation exposure and survival through to weaning for 20 industry flocks from 2003 to 2004 (15,821 lambs). Ewes with higher body condition scores in mid pregnancy had heavier lambs at birth (P < 0.01). Lambs weighing 5.5 to 6 kg at birth (P < 0.01) were more likely to be viable at birth and survive to weaning than heavier or lighter lambs. Weather conditions during late pregnancy (P < 0.05) proved more important than conditions during lambing (P < 0.05) in determining lamb viability and survival through to weaning. Older ewes and ewes with triplets require considerably more attention for farmers to realize their production potential. This information can help formulate appropriate management programs to improve lamb survival rates under easy care farming systems.

Naval Enterprise Engineering: Design, Innovate and Train (NEEDIT)

DTIC Science & Technology

2015-03-04

world and we are somewhat able to stand on the shoulders of giants in Naval Engineering and inherit baseline designs that, in most cases, represent a...Set-Based Design) maximizes design flexibility ( Lamb 2003). However, it may add some risk to schedule or require program managers to trust that the...spiral or Set based design. A design philosophy is a weighted list of attributes used in the evaluation of alternatives ( Lamb 2003). Design leadership

Assessment of commercial lamb meat quality by British and Spanish taste panels.

PubMed

Sañudo, C; Nute, G R; Campo, M M; María, G; Baker, A; Sierra, I; Enser, M E; Wood, J D

1998-01-01

Trained sensory panels in Britain and Spain assessed loin meat from commercial lambs purchased in Spain, which included Welsh lamb (imported from Britain) and two Spanish breeds (Merino and Rasa Aragonesa). The British panel also assessed British lamb purchased in local butcher shops and supermarkets. Sensory panels, in each country, received meat from the same lambs and used their local methods of cooking and assessment. Spanish panels used unstructured line scales to measure lamb odour intensity, tenderness, juiciness, lamb flavour intensity and two hedonic scales of flavour liking and overall liking. The British panel used 8 point category scales with the same attributes. Results from both panels in objective parameters were in agreement, hence showing that different trained sensory panels may arrive at the same conclusion. However, when panellists were allowed to make hedonic judgements (preference), the British panel preferred British lamb and the Spanish panel preferred Spanish lamb. This finding has important consequences for lamb producers who export their lambs and demonstrates that the underlying reasons for different preferences should be investigated. Production variables are discussed in relation to their influence on lamb eating quality and as a way to tailor lamb eating quality attributes familiar to consumers in the importing country.

Observation of skull-guided acoustic waves in a water-immersed murine skull using optoacoustic excitation

NASA Astrophysics Data System (ADS)

Estrada, Héctor; Rebling, Johannes; Razansky, Daniel

2017-02-01

The skull bone, a curved solid multilayered plate protecting the brain, constitutes a big challenge for the use of ultrasound-mediated techniques in neuroscience. Ultrasound waves incident from water or soft biological tissue are mostly reflected when impinging on the skull. To this end, skull properties have been characterized for both high-intensity focused ultrasound (HIFU) operating in the narrowband far-field regime and optoacoustic imaging applications. Yet, no study has been conducted to characterize the near-field of water immersed skulls. We used the thermoelastic effect with a 532 nm pulsed laser to trigger a wide range of broad-band ultrasound modes in a mouse skull. In order to capture the waves propagating in the near-field, a thin hydrophone was scanned in close proximity to the skull's surface. While Leaky pseudo-Lamb waves and grazing-angle bulk water waves are clearly visible in the spatio-temporal data, we were only able to identify skull-guided acoustic waves after dispersion analysis in the wavenumber-frequency space. The experimental data was found to be in a reasonable agreement with a flat multilayered plate model.

Low pasture allowance until late gestation in ewes: behavioural and physiological changes in ewes and lambs from lambing to weaning.

PubMed

Freitas-de-Melo, A; Ungerfeld, R; Hötzel, M J; Orihuela, A; Pérez-Clariget, R

2017-02-01

Low pasture allowance during gestation affects ewes' BW at parturition, the bond with their lamb, lamb development, and thus also may affect their responses to weaning. The objectives were to determine if native pasture allowance from before conception until late pregnancy affects ewe-lamb behaviours at lambing, ewes' milk yield, lambs' BW, and the behavioural and physiological changes of ewes and lambs at weaning. From 23 days before conception until 122 days of pregnancy, 24 ewes grazed on two different native pasture allowances: high (10 to 12 kg of dry matter (DM)/100 kg of BW per day; HPA treatment; n=12) or low (5 to 8 kg of DM/100 kg of BW per day; LPA treatment; n=12). Thereafter, all ewes grazed on Festuca arundinacea and received rice bran and crude glycerine. Ewes' body condition score (BCS) and BW were recorded during pregnancy and postpartum periods. Milk yield was determined on days 32, 41 and 54 after lambing. Lambs' BW was recorded from birth until 72 days after lambing. Latency from parturition until the ewe licked her lamb, maternal behaviour score (a test that evaluates maternal attachment to the lamb) and latency for lamb to stand up and suckle were determined. The behaviour of the lambs and ewes was recorded before and after weaning (at 65 days). The ewes' serum total protein, albumin and globulin concentrations were measured before and after weaning. The HPA ewes presented greater BW (P<0.005) and BCS (P<0.005) than the LPA ewes during pregnancy and postpartum (P<0.04), and had a greater milk yield than the LPA ewes (P<0.03). Treatments did not influence any behaviour at lambing, lambs' BW, neither the ewes' behavioural and physiological changes at weaning. HPA lambs paced and vocalized more than LPA lambs (P<0.0001). The variation of albumin concentration before and after weaning was greater in the HPA lambs than in the LPA lambs (P<0.0001). In conclusion, although ewes' BW, BCS and milk production were affected by pasture allowance until late pregnancy, this did not affect the behaviours that lead to the establishment of the mother-young bond, nor the ewes' behavioural responses at weaning. Lambs reared by ewes that grazed on low pasture allowance during pregnancy presented fewer behavioural changes and a lower decrease of albumin concentration after weaning. Lambs' BW was not affected by the feeding received by their mothers.

Adaptive elastic metasurfaces for wave front manipulation

NASA Astrophysics Data System (ADS)

Li, Shilong; Xu, Jiawen; Tang, Jiong

2018-04-01

In this research, by combining the concept of elastic metasurfaces with piezoelectric transducer with shunted circuitry, we investigate the designs of elastic metasurfaces, consisting of an array of piezoelectric transducers shunted with negative capacitance, which is capable of modulating wave fronts adaptively. In order to construct different adaptive elastic metasurfaces, different phase profiles along the interface can be framed through properly adjusting the negative capacitance values. Flat planar lenses for focusing transmitted A0 Lamb waves are achieved, and possess the flexibility of changing focal locations through electromechanical tunings. Additionally, nonparaxial self-bending beams with arbitrary trajectories and source illusion devices can also be accomplished owing to the free manipulation of phase shifts. With their versatility and tunability, the adaptive elastic metasurfaces could pave new avenues to a wide variety of potential applications, such as nondestructive testing, ultrasound imaging, and caustic engineering.

Ultrasonic stress wave characterization of composite materials

NASA Technical Reports Server (NTRS)

Duke, J. C., Jr.; Henneke, E. G., II; Stinchcomb, W. W.

1986-01-01

The work reported covers three simultaneous projects. The first project was concerned with: (1) establishing the sensitivity of the acousto-ultrasonic method for evaluating subtle forms of damage development in cyclically loaded composite materials, (2) establishing the ability of the acousto-ultrasonic method for detecting initial material imperfections that lead to localized damage growth and final specimen failure, and (3) characteristics of the NBS/Proctor sensor/receiver for acousto-ultrasonic evaluation of laminated composite materials. The second project was concerned with examining the nature of the wave propagation that occurs during acoustic-ultrasonic evaluation of composite laminates and demonstrating the role of Lamb or plate wave modes and their utilization for characterizing composite laminates. The third project was concerned with the replacement of contact-type receiving piezotransducers with noncontacting laser-optical sensors for acousto-ultrasonic signal acquisition.

Guided wave mode selection for inhomogeneous elastic waveguides using frequency domain finite element approach.

PubMed

Chillara, Vamshi Krishna; Ren, Baiyang; Lissenden, Cliff J

2016-04-01

This article describes the use of the frequency domain finite element (FDFE) technique for guided wave mode selection in inhomogeneous waveguides. Problems with Rayleigh-Lamb and Shear-Horizontal mode excitation in isotropic homogeneous plates are first studied to demonstrate the application of the approach. Then, two specific cases of inhomogeneous waveguides are studied using FDFE. Finally, an example of guided wave mode selection for inspecting disbonds in composites is presented. Identification of sensitive and insensitive modes for defect inspection is demonstrated. As the discretization parameters affect the accuracy of the results obtained from FDFE, effect of spatial discretization and the length of the domain used for the spatial fast Fourier transform are studied. Some recommendations with regard to the choice of the above parameters are provided. Copyright © 2015 Elsevier B.V. All rights reserved.

2D Analytical Model for the Directivity Prediction of Ultrasonic Contact Type Transducers in the Generation of Guided Waves.

PubMed

Tiwari, Kumar Anubhav; Raisutis, Renaldas; Mazeika, Liudas; Samaitis, Vykintas

2018-03-26

In this paper, a novel 2D analytical model based on the Huygens's principle of wave propagation is proposed in order to predict the directivity patterns of contact type ultrasonic transducers in the generation of guided waves (GWs). The developed model is able to estimate the directivity patterns at any distance, at any excitation frequency and for any configuration and shape of the transducers with prior information of phase dispersive characteristics of the guided wave modes and the behavior of transducer. This, in turn, facilitates to choose the appropriate transducer or arrays of transducers, suitable guided wave modes and excitation frequency for the nondestructive testing (NDT) and structural health monitoring (SHM) applications. The model is demonstrated for P1-type macro-fiber composite (MFC) transducer glued on a 2 mm thick aluminum (Al) alloy plate. The directivity patterns of MFC transducer in the generation of fundamental guided Lamb modes (the S0 and A0) and shear horizontal mode (the SH0) are successfully obtained at 80 kHz, 5-period excitation signal. The results are verified using 3D finite element (FE) modelling and experimental investigation. The results obtained using the proposed model shows the good agreement with those obtained using numerical simulations and experimental analysis. The calculation time using the analytical model was significantly shorter as compared to the time spent in experimental analysis and FE numerical modelling.

Hybrid Numerical-Analytical Scheme for Calculating Elastic Wave Diffraction in Locally Inhomogeneous Waveguides

NASA Astrophysics Data System (ADS)

Glushkov, E. V.; Glushkova, N. V.; Evdokimov, A. A.

2018-01-01

Numerical simulation of traveling wave excitation, propagation, and diffraction in structures with local inhomogeneities (obstacles) is computationally expensive due to the need for mesh-based approximation of extended domains with the rigorous account for the radiation conditions at infinity. Therefore, hybrid numerical-analytic approaches are being developed based on the conjugation of a numerical solution in a local vicinity of the obstacle and/or source with an explicit analytic representation in the remaining semi-infinite external domain. However, in standard finite-element software, such a coupling with the external field, moreover, in the case of multimode expansion, is generally not provided. This work proposes a hybrid computational scheme that allows realization of such a conjugation using a standard software. The latter is used to construct a set of numerical solutions used as the basis for the sought solution in the local internal domain. The unknown expansion coefficients on this basis and on normal modes in the semi-infinite external domain are then determined from the conditions of displacement and stress continuity at the boundary between the two domains. We describe the implementation of this approach in the scalar and vector cases. To evaluate the reliability of the results and the efficiency of the algorithm, we compare it with a semianalytic solution to the problem of traveling wave diffraction by a horizontal obstacle, as well as with a finite-element solution obtained for a limited domain artificially restricted using absorbing boundaries. As an example, we consider the incidence of a fundamental antisymmetric Lamb wave onto surface and partially submerged elastic obstacles. It is noted that the proposed hybrid scheme can also be used to determine the eigenfrequencies and eigenforms of resonance scattering, as well as the characteristics of traveling waves in embedded waveguides.

Evaluation of the South African Dorper as a terminal sire breed for growth, carcass, and palatability characteristics.

PubMed

Snowders, G D; Duckett, S L

2003-02-01

The South African Dorper is an important terminal meat sire breed in Africa that was recently imported into the United States. The objective of this study was to evaluate the Dorper as a terminal meat sire breed for U.S. production. Semen from purebred Dorper sires was used to artificially inseminate Columbia ewes to produce F1 crossbred lambs. Growth and carcass characteristics of F1 Dorper-Columbia lambs (n = 165), F1 Suffolk-Columbia (n = 89), and purebred Columbia lambs (n = 207) were compared based on subsets of the total number of animals. The F1 Dorper lambs grew significantly slower (313 g x d(-1)) and weighed less (29.8 kg) than F1 Suffolk- (357 g x d(-1), 33.5 kg) and Columbia-sired lambs (328 g x d(-1), 31 kg) at 77 d of age. However, at a weaning age of 118 d weaning weight and ADG did not differ (P > 0.20) among sire breed groups. Postweaning growth of F1 Dorper(239 g xd(-1)) wether lambs did not differ from that of purebred Columbia wethers (230 g x d(-1)) but was less than that of F1 Suffolk lambs (259 g x d(-1); P= 0.09). Feed efficiency did not differ among breed types. Breed types had similar dressing percentages (53%), shoulder fat depth (2.8 mm), body wall thickness (3 cm), leg conformation score (Choice), Yield grade (2.4), and Quality grade (Choice). Weight of wholesale shoulders and racks made up approximately 38% of the carcass weight in the Columbia and F1 Suffolk-Columbia type but only 33% in the F1 Dorper-Columbia lambs. However, the more expensive wholesale loins from F1 Dorpers were heavier (P < 0.01) than the other breed types. Total weights of wholesale legs were similar among F1 Dorpers and F1 Suffolks but were heavier than those for the purebred Columbia (P < 0.05). Percentages of total wholesale primal cuts were similar among breed types (P > 0.10). Chemical composition of the carcass did not differ significantly between breed types with a mean composition of 52% moisture, 30% lipid (ether extract), 17% protein, and 0.76% ash. Warner-Bratzler shear force values were less (P < 0.05) and sensory panel ratings for tenderness were significantly more favorable for lamb chops from Dorper sired lambs. Dorper rams can be used as terminal meat sires to produce lambs whose growth rate to 118 d of weaning age, postweaning ADG and feed efficiency, and carcass characteristics are similar to that of Suffolk crossbred lambs and purebred Columbia lambs but with a slight improvement in tenderness.

Effects of suckling duration on growth, slaughtering and carcass quality characteristics of Kivircik lambs.

PubMed

Ekiz, Bulent; Kocak, Omur; Yalcintan, Hulya; Yilmaz, Alper

2016-02-01

Effects of suckling length (45, 75 and 120 days) and birth type (single and twin) on lamb growth, slaughtering and carcass quality characteristics were investigated using 40 Kivircik lambs. SC-45 and SC-75 lambs were weaned at 45 and 75 days of age, respectively, whilst SC-120 lambs remained with their mothers until the end of the experimental period. Lambs from all studied groups were slaughtered at 120 days of age. Weaning treatment caused a decrease in average daily gain in SC-45 and SC-75 lambs, and therefore, final weight was higher in SC-120 lambs than lambs from weaned groups. SC-120 lambs had higher empty body weight, cold carcass weight, dressing percentage, carcass measurements, carcass fatness (proportions of the kidney knob and channel fat, subcutaneous and intramuscular fat in pelvic limb) and non-carcass fatness (omental and mesenteric fat proportion) than weaned lambs. As a conclusion, the potential losses in meat production due to weaning should be considered before deciding the weaning of lambs at early ages.

7 CFR 1280.111 - Lamb.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.111 Lamb. Lamb means ovine animals of any age, including ewes and rams. ...

7 CFR 1280.111 - Lamb.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.111 Lamb. Lamb means ovine animals of any age, including ewes and rams. ...

7 CFR 1280.111 - Lamb.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.111 Lamb. Lamb means ovine animals of any age, including ewes and rams. ...

7 CFR 1280.111 - Lamb.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.111 Lamb. Lamb means ovine animals of any age, including ewes and rams. ...

Room temperature elastic properties of Rh-based alloys studied by surface Brillouin scattering

NASA Astrophysics Data System (ADS)

Sumanya, C.; Mathe, B. A.; Comins, J. D.; Every, A. G.; Osawa, M.; Harada, H.

2014-10-01

Platinum metal group alloys are promising materials for use in a new generation of gas turbine engines owing to their excellent high-temperature properties. In the present work, room temperature elastic properties of single crystals of Rh3Nb and Rh3Zr are investigated. Surface Brillouin scattering spectra for a range of wave vector directions on the (001) surface have been acquired in order to determine the angular variation of the velocities of the Rayleigh and pseudo-surface acoustic waves and that of the longitudinal lateral wave (LLW) threshold within the Lamb shoulder. The elastic stiffness constants C11, C12, and C44 of these cubic crystal specimens have been derived using two approaches: the first involving the least-squares fit of the combined measured wave velocity data to calculated values and the second an analytical approach using the Rayleigh velocities in the [100] and [110] directions and LLW velocity in the [100] direction, and extracting the elastic stiffness constants from the secular equations for these velocities. Results from the two methods are in good agreement and are for Rh3Nb, C11 = 368 ± 3, C12 = 186 ± 5, and C44 = 161 ± 3 in GPa; and for Rh3Zr, C11 = 329 ± 4, C12 = 185 ± 6, and C44 = 145 ± 4 in GPa.

A preference-based approach to deriving breeding objectives: applied to sheep breeding.

PubMed

Byrne, T J; Amer, P R; Fennessy, P F; Hansen, P; Wickham, B W

2012-05-01

Using internet-based software known as 1000Minds, choice-experiment surveys were administered to experts and farmers from the Irish sheep industry to capture their preferences with respect to the relative importance - represented by part-worth utilities - of target traits in the definition of a breeding objective for sheep in Ireland. Sheep production in Ireland can be broadly separated into lowland and hill farming systems; therefore, each expert was asked to answer the survey first as if he or she were a lowland farmer and second as a hill farmer. In addition to the experts, a group of lowland and a group of hill farmers were surveyed to assess whether, and to what extent, the groups' preferences differ from the experts' preferences. The part-worth utilities obtained from the surveys were converted into relative economic value terms per unit change in each trait. These measures - referred to as 'preference economic values' (pEVs) - were compared with economic values for the traits obtained from bio-economic models. The traits 'value per lamb at the meat processor' and 'lamb survival to slaughter' were revealed as being the two most important traits for the surveyed experts responding as lowland and hill farmers, respectively. In contrast, 'number of foot baths per year for ewes' and 'number of anthelmintic treatments per year for ewes' were the two least important traits. With the exception of 'carcase fat class' (P < 0.05), there were no statistically significant differences in the mean pEVs obtained from the surveyed experts under both the lowland and hill farming scenarios. Compared with the economic values obtained from bio-economic models, the pEVs for 'lambing difficulty' when the experts responded as lowland farmers were higher (P < 0.001); and they were lower (P < 0.001) for 'carcase conformation class', 'carcase fat class' (less negative) and 'ewe mature weight' (less negative) under both scenarios. Compared with surveyed experts, pEVs from lowland farmers differed significantly for 'lambing difficulty', 'lamb survival to slaughter', 'average days to slaughter of lambs', 'number of foot baths per year for ewes', 'number of anthelmintic treatments per year for ewes' and 'ewe mature weight'. Compared with surveyed experts, pEVs from hill farmers differed significantly for 'lambing difficulty', 'average days to slaughter of lambs' and 'number of foot baths per year for ewes'. This study indicates that preference-based tools have the potential to contribute to the definition of breeding objectives where production and price data are not available.

Humoral immune response against two surface antigens of Chlamydia pecorum in vaccinated and naturally infected sheep.

PubMed

Bommana, Sankhya; Walker, Evelyn; Desclozeaux, Marion; Timms, Peter; Polkinghorne, Adam

2017-01-01

Chlamydia pecorum is a globally recognised livestock pathogen due to the significant clinical and economic impact it poses to livestock producers. Routine serological diagnosis is through a complement fixation test (CFT), which is often criticised for cross-reactivity, poor sensitivity and specificity. Although serology remains the preferred method in veterinary diagnostic laboratories, serological assays based on surface antigens of C. pecorum have not been established until now. In this study, we evaluated the use of two chlamydial recombinant protein antigens (PmpG and MOMP-G) by a direct IgG ELISA method for detection of ovine anti-chlamydial antibodies. Using the Pepscan method we then identified B cell epitopes across PmpG and MOMP-G proteins, in lambs with (a) naturally occurring asymptomatic C. pecorum infections (b) C. pecorum-associated polyarthritis and (c) recombinant PmpG and MOMP-G vaccine. Plasma IgG antibodies to PmpG in natural infection of lambs were detected earlier in infection than CFT and served as an acute phase marker. Antibodies to MOMP-G IgG were significantly heightened in lambs with C. pecorum-associated polyarthritis. PmpG and MOMP-G specific B-cell epitope mapping revealed epitope responses in immunised lambs cluster with some of the epitope responses in naturally infected lambs. B-cell epitope mapping further revealed that lambs with polyarthritis recognised several unique PmpG (50% frequency, peptide 8, 25, 40, 41 and 50) and MOMP (50% frequency, peptide 50) epitopes in comparison to asymptomatic infections. The findings of this study will have implications towards improved serodiagnosis of C. pecorum infections in livestock and inform the downstream development of alternative peptide-based antigens for future C. pecorum vaccine studies.

Three-year evaluation of best practice guidelines for nematode control on commercial sheep farms in the UK.

PubMed

Learmount, Jane; Stephens, Nathalie; Boughtflower, Valerie; Barrecheguren, Alba; Rickell, Kayleigh; Massei, Giovanna; Taylor, Mike

2016-08-15

Anthelmintics are commonly used on the majority of UK commercial sheep farms to reduce major economic losses associated with parasitic diseases. With increasing anthelmintic resistance worldwide, several countries have produced evidence-based, best practice guidelines with an example being the UK's Sustainable Control of Parasites in Sheep (SCOPS) initiative. In 2012, a pilot study demonstrated that SCOPS-managed farms used fewer anthelmintic treatments than traditionally managed farms, with no impact on lamb productivity and worm burden. Building on these results, we collected data for three consecutive years (2012-2014) with the following aims: (1) To compare the effects of traditional and SCOPS-based parasite management on lamb productivity and worm burden; (2) To evaluate the effect of region and farm type on lamb productivity and worm burden; (3) To compare the frequency and patterns of use of anthelmintic treatment on traditional and SCOPS-managed farms. The study was carried out on 16 farms located in the North east and the South west of England and Wales. Lamb productivity was assessed by quantifying birth, mid-season and finish weights and calculating daily live-weight gains and time to finish in a cohort of 40-50 lambs on each farm. Five annual faecal egg counts were carried out on each farm to assess worm burden. No differences in lamb productivity and worm burdens were found between farms that adopted SCOPS guidelines and traditional farms across the three years. However, mean infection levels increased for both the SCOPS and the traditional groups. Lamb production was not significantly different for farm type and region but the effect of region on infection was significant. For both ewes and lambs, SCOPS farms carried out significantly fewer anthelmintic treatments per year, and used fewer anthelmintic doses/animal than traditional farms. The data suggest a trend to increasing use of anthelmintics in ewes on traditional but not on the SCOPS farms and a decreasing use of anthelmintics in lambs on both SCOPS and traditional farms. Across time, an increasing number of SCOPS farmers left their ewes and lambs untreated and the reverse was true for traditional farmers. Overall, farms implementing SCOPS guidelines used less anthelmintic treatments and less frequently than traditionally managed farms, without loss of animal performance or increased worm burden. Implementing SCOPS guidelines might have economic benefits for farmers, help reduce development of anthelmintic resistance on farms and decrease any environmental impact of anthelmintics. Furthermore, these data suggest some important epidemiological trends that should be investigated in long-term studies. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

Carcass and meat quality of Assaf milk fed lambs: Effect of rearing system and sex.

PubMed

Rodríguez, A B; Landa, R; Bodas, R; Prieto, N; Mantecón, A R; Giráldez, F J

2008-10-01

The effect of sex and rearing system on growth and carcass and meat characteristics of milk fed Assaf lambs was studied. Thirty-six lambs, 18 males and 18 females were used. Twelve lambs remained with their mothers throughout the experiment (NR). Within 24-36h of birth, the rest were housed individually and fed twice a day ad libitum (AAR) or at 70% of ad libitum consumption (RAR) with reconstituted cow's milk. Sex did not affect animal performance, yet females showed higher carcass and non-carcass fat deposits. NR lambs showed greater BWG than AAR fed lambs, and AAR, higher than the RAR. Differences between naturally and artificially reared lambs in CCW and killing out percentage were not significant. Empty digestive tract and mesenteric fat weights were greater for RAR than NR lambs, with the AAR lambs demonstrating intermediate values; conversely, omental fat was greater in NR lambs. Carcass ether extract content was greater for NR lambs, possibly due to the greater growth. Use of ad libitum cow's milk substitute in suckling lambs twice a day resulted in less body weight gain but similar killing out percentages compared to naturally raised lambs. A 70% restricted supply increased the days in suckling and reduced carcass fatness and compactness. Except for water loss, which was less in NR than artificially fed lambs, no differences were found in meat characteristics.

Effect of system of lamb rearing and season on early post-partum fertility of ewes and growth performance of lambs in Katahdin sheep.

PubMed

Rastle-Simpson, S; D'Souza, K; Redhead, A; Singh-Knights, D; Baptiste, Q; Knights, M

2017-10-01

The effect of season (S), lamb rearing system (RT) and grain supplementation (GS) on post-partum fertility in Katahdin ewes and growth in Katahdin lambs was evaluated. Katahdin ewes were bred to lamb in fall (n = 36) or spring (n = 56) and at approximately 2.5 months post-partum were randomly assigned to be permanently separated or to continue to suckle their lambs for an additional 3 months. All ewes were joined with rams following treatment to synchronize oestrus. Weaned (W, n = 84) and continuously suckled lambs (CSK, n = 88) were fed forage only (n = 84; hay and pasture for fall- and spring-born lambs respectively) or were supplemented (n = 88; 18% crude protein ration ad libitum) and all weighed biweekly. Ewes rebred in the fall had a shorter ram introduction to lambing interval (p < 0.05), higher prolificacy (p = 0.001) and higher lambing rates (p = 0.02); however, the proportion of ewes lambing was not affected by season. The first service lambing rate was lower in ewes continuously suckling lambs in the spring, but not in the fall breeding season (S × RT, p = 0.03). Lambs that continuously suckled their dams and were supplemented grew quicker and gained more (p < 0.001) than their weaned and unsupplemented counterparts. The effect of CSK on growth rate of lambs was greater in the spring (RT × S; p = 0.05), and the effect of supplementation on growth rate of lambs was greater in the fall (GS × S; p < 0.0001). In conclusion, Katahdin lambs achieved higher weight gains from continuous suckling and grain supplementation. Moreover, Katahdin ewes are capable of early rebreeding post-partum while suckling their lambs, which makes them suited for use in accelerated lambing programmes. Journal of Animal Physiology and Animal Nutrition © 2016 Blackwell Verlag GmbH.

Observations on the alimentary tract of gnotobiotic lambs.

PubMed

Lysons, R J; Alexander, T J; Wellstead, P D; Jennings, I W

1976-01-01

Seventeen gnotobiotic lambs were reared up to 21 weeks of age on cows' milk followed by sterile solid diets similar to diets fed to conventional lambs. Seven were inoculated with limited defined populations of rumen bacteria, seven were left uninoculated and three were dosed with rumen contents from conventional sheep ('conventionalised'). Seven naturally-born lambs were reared for purposes of comparison. As with other species of gnotobiotic animals, both the inoculated and the uninoculated gnotobiotic lambs had small, poorly developed lymph nodes, soft colon contents and thin intestinal walls. Unlike other species the caeca of gnotobiotic lambs were of normal size. The overall size of the reticulo-rumen including contents relative to body weight was similar in gnotobiotic and conventional lambs. However, macroscopically, the musculature of the rumen seemed to be poorly developed and histological studies showed hypoplasia of the muscle tissue of both the rumen and reticulum. Rumination was noted only infrequently in gnotobiotic lambs. The epithelium of the rumen and reticulum of the uninoculated gnotobiotic lambs was similar to that of neonatal lambs, but there was normal development of papillae in gnotobiotic lambs inoculated with limited defined populations of rumen bacteria and in conventionalised lambs. Degenerative changes were observed histologically in some of the organs of gnotobiotic lambs which were consistent with nutritional deficiencies.

Ocean Wave-to-Ice Energy Transfer Determined from Seafloor Pressure and Ice Shelf Seismic Observations

NASA Astrophysics Data System (ADS)

Chen, Z.; Bromirski, P. D.; Gerstoft, P.; Stephen, R. A.; Wiens, D.; Aster, R. C.; Nyblade, A.

2017-12-01

Ice shelves play an important role in buttressing land ice from reaching the sea, thus restraining the rate of sea level rise. Long-period gravity wave impacts excite vibrations in ice shelves that may trigger tabular iceberg calving and/or ice shelf collapse events. Three kinds of seismic plate waves were continuously observed by broadband seismic arrays on the Ross Ice Shelf (RIS) and on the Pine Island Glacier (PIG) ice shelf: (1) flexural-gravity waves, (2) flexural waves, and (3) extensional Lamb waves, suggesting that all West Antarctic ice shelves are subjected to similar gravity wave excitation. Ocean gravity wave heights were estimated from pressure perturbations recorded by an ocean bottom differential pressure gauge at the RIS front, water depth 741 m, about 8 km north of an on-ice seismic station that is 2 km from the shelf front. Combining the plate wave spectrum, the frequency-dependent energy transmission and reflection at the ice-water interface were determined. In addition, Young's modulus and Poisson's ratio of the RIS are estimated from the plate wave motions, and compared with the widely used values. Quantifying these ice shelf parameters from observations will improve modeling of ice shelf response to ocean forcing, and ice shelf evolution.

Modeling the high-frequency complex modulus of silicone rubber using standing Lamb waves and an inverse finite element method.

PubMed

Jonsson, Ulf; Lindahl, Olof; Andersson, Britt

2014-12-01

To gain an understanding of the high-frequency elastic properties of silicone rubber, a finite element model of a cylindrical piezoelectric element, in contact with a silicone rubber disk, was constructed. The frequency-dependent elastic modulus of the silicone rubber was modeled by a fourparameter fractional derivative viscoelastic model in the 100 to 250 kHz frequency range. The calculations were carried out in the range of the first radial resonance frequency of the sensor. At the resonance, the hyperelastic effect of the silicone rubber was modeled by a hyperelastic compensating function. The calculated response was matched to the measured response by using the transitional peaks in the impedance spectrum that originates from the switching of standing Lamb wave modes in the silicone rubber. To validate the results, the impedance responses of three 5-mm-thick silicone rubber disks, with different radial lengths, were measured. The calculated and measured transitional frequencies have been compared in detail. The comparison showed very good agreement, with average relative differences of 0.7%, 0.6%, and 0.7% for the silicone rubber samples with radial lengths of 38.0, 21.4, and 11.0 mm, respectively. The average complex elastic moduli of the samples were (0.97 + 0.009i) GPa at 100 kHz and (0.97 + 0.005i) GPa at 250 kHz.

Just the Facts? the Separation of Sex Education from Moral Education

ERIC Educational Resources Information Center

Lamb, Sharon

2013-01-01

In this essay Sharon Lamb considers how progressives have begun to win the longstanding battle to shape sex education and what they have had to give up in the process. After framing the battle in historical context, Lamb uses discourse analysis to explore the hidden values in the "evidence-based" (EB) curricula that progressives…

Novel ENAM and LAMB3 mutations in Chinese families with hypoplastic amelogenesis imperfecta.

PubMed

Wang, Xin; Zhao, Yuming; Yang, Yuan; Qin, Man

2015-01-01

Amelogenesis imperfecta is a group of inherited diseases affecting the quality and quantity of dental enamel. To date, mutations in more than ten genes have been associated with non-syndromic amelogenesis imperfecta (AI). Among these, ENAM and LAMB3 mutations are known to be parts of the etiology of hypoplastic AI in human cases. When both alleles of LAMB3 are defective, it could cause junctional epidermolysis bullosa (JEB), while with only one mutant allele in the C-terminus of LAMB3, it could result in severe hypoplastic AI without skin fragility. We enrolled three Chinese families with hypoplastic autosomal-dominant AI. Despite the diagnosis falling into the same type, the characteristics of their enamel hypoplasia were different. Screening of ENAM and LAMB3 genes was performed by direct sequencing of genomic DNA from blood samples. Disease-causing mutations were identified and perfectly segregated with the enamel defects in three families: a 19-bp insertion mutation in the exon 7 of ENAM (c.406_407insTCAAAAAAGCCGACCACAA, p.K136Ifs*16) in Family 1, a single-base deletion mutation in the exon 5 of ENAM (c. 139delA, p. M47Cfs*11) in Family 2, and a LAMB3 nonsense mutation in the last exon (c.3466C>T, p.Q1156X) in Family 3. Our results suggest that heterozygous mutations in ENAM and LAMB3 genes can cause hypoplastic AI with markedly different phenotypes in Chinese patients. And these findings extend the mutation spectrum of both genes and can be used for mutation screening of AI in the Chinese population.

7 CFR 1280.206 - Certification of organizations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Lamb Promotion... substantial quantity of lamb or lamb products; and (2) A primary purpose of the organization is in the...

Studies on the essentiality of chromium in ruminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samsell, L.J.; Spears, J.W.

1986-03-01

Although chromium has been established as an essential trace element for certain animal species, no requirement has been shown for ruminants. Sixteen female lambs (35 kg) were used in an attempt to determine if chromium is essential in the ruminant. Animals were individually housed in all plastic pens and fed twice daily either a low chromium (100 ppb) torula yeast based diet or the basal diet supplemented with 10 ppm chromium as CrCl/sub 3/. Blood samples obtained prior to the morning feeding and 2 and 6 hr post-feeding on days 28 and 56 indicated no significant treatment differences in plasmamore » glucose or serum free fatty acids. By day 56, serum cholesterol tended to be lower in chromium supplemented lambs (60.9 vs 71.7 mg/dl). Lambs in the chromium supplemented treatment also tended to gain more efficiently through 56 days (.130 vs .118 gain/fed). On day 84, lambs were bled after a 48 hr fast, refed, then bled again at 2 and 6 hr post-feeding. Plasma glucose and serum free fatty acids were not affected by chromium at the end of the 48 hr fast or when lambs were refed following fasting. At 84 days both total serum cholesterol and HDL-cholesterol were lower in lambs receiving supplemental chromium. These results suggest that chromium may have a biological role in the ruminant.« less

Quantifying the Risk of Human Toxoplasma gondii Infection Due to Consumption of Domestically Produced Lamb in the United States.

PubMed

Guo, Miao; Mishra, Abhinav; Buchanan, Robert L; Dubey, Jitender P; Hill, Dolores E; Gamble, H Ray; Pradhan, Abani K

2016-07-01

Toxoplasma gondii is a prevalent protozoan parasite worldwide. Human toxoplasmosis is responsible for considerable morbidity and mortality in the United States, and meat products have been identified as an important source of T. gondii infections in humans. The goal of this study was to develop a farm-to-table quantitative microbial risk assessment model to predict the public health burden in the United States associated with consumption of U.S. domestically produced lamb. T. gondii prevalence in market lambs was pooled from the 2011 National Animal Health Monitoring System survey, and the concentration of the infectious life stage (bradyzoites) was calculated in the developed model. A log-linear regression and an exponential doseresponse model were used to model the reduction of T. gondii during home cooking and to predict the probability of infection, respectively. The mean probability of infection per serving of lamb was estimated to be 1.5 cases per 100,000 servings, corresponding to ∼6,300 new infections per year in the U.S. Based on the sensitivity analysis, we identified cooking as the most effective method to influence human health risk. This study provided a quantitative microbial risk assessment framework for T. gondii infection through consumption of lamb and quantified the infection risk and public health burden associated with lamb consumption.

Acidovorax valerianellae sp. nov., a novel pathogen of lamb's lettuce [Valerianella locusta (L.) Laterr].

PubMed

Gardan, Louis; Stead, David E; Dauga, Catherine; Gillis, Moniek

2003-05-01

Bacterial spot disease of lamb's lettuce [Valerianella locusta (L.) Laterr.] was first observed in fields in 1991. This new bacterial disease is localized in western France in high-technology field production of lamb's lettuce for the preparation of ready-to-use salad. Nineteen strains isolated in 1992 and 1993 from typical black leaf spots of naturally infected lamb's lettuce were characterized and compared with reference strains of Acidovorax and Delftia. The pathogenicity of the 19 strains was confirmed by artificial inoculation. Biochemical and physiological tests, fatty acid profiles, DNA-DNA hybridization and other nucleic acid-based tests were performed. A numerical taxonomic analysis of the 19 lamb's lettuce strains showed a single homogeneous phenon closely related to previously described phytopathogenic taxa of the genus Acidovorax. DNA-DNA hybridization studies showed that the lamb's lettuce strains were 91-100% related to a representative strain, strain CFBP 4730(T), and constituted a discrete DNA hybridization group, indicating that they belong to the same novel species. Results from DNA-rRNA hybridization, 16S rRNA sequence analysis and fatty acid analysis studies confirmed that this novel species belongs to the beta-subclass of the Proteobacteria and, more specifically, to the family Comamonadaceae and the genus Acidovorax. The name Acidovorax valerianellae sp. nov. is proposed for this novel taxon of phytopathogenic bacteria. The type strain is strain CFBP 4730(T) (= NCPPB 4283(T)).

The effect of tilmicosin administered to ewes prior to lambing on incidence of clinical mastitis and subsequent lamb performance.

PubMed Central

Croft, A; Duffield, T; Menzies, P; Leslie, K; Bagg, R; Dick, P

2000-01-01

The effect of tilmicosin on the incidence of clinical mastitis and subsequent lamb performance was studied in 9 sheep flocks in Ontario. Ewes were treated randomly with either tilmicosin or placebo approximately one month prior to lambing. Outcome was assessed by comparing rates of clinical mastitis, palpable udder abnormalities, and preweaning (50-day) lamb weights between the 2 treatment groups, while controlling for other important variables. Lambs raised by multiparous ewes treated with tilmicosin were significantly heavier than lambs from placebo-treated multiparous ewes at 50 days. Lambs from tilmicosin-treated ewes were on average 0.52 kg heavier than lambs in the placebo group. There was no difference between treatment groups in the weight of lambs from first parity ewes. Tilmicosin treatment resulted in a 43% decrease in palpable udder abnormalities. Incidence of clinical mastitis did not differ between experimental groups. The administration of tilmicosin prelambing, at the time of routine clostridial disease vaccination, may be a beneficial and convenient way to reduce mastitis infection and improve the preweaning gain of lambs. PMID:10769768

Lamb wave detection of limpet mines on ship hulls.

PubMed

Bingham, Jill; Hinders, Mark; Friedman, Adam

2009-12-01

This paper describes the use of ultrasonic guided waves for identifying the mass loading due to underwater limpet mines on ship hulls. The Dynamic Wavelet Fingerprint Technique (DFWT) is used to render the guided wave mode information in two-dimensional binary images because the waveform features of interest are too subtle to identify in time domain. The use of wavelets allows both time and scale features from the original signals to be retained, and image processing can be used to automatically extract features that correspond to the arrival times of the guided wave modes. For further understanding of how the guided wave modes propagate through the real structures, a parallel processing, 3D elastic wave simulation is developed using the finite integration technique (EFIT). This full field, technique models situations that are too complex for analytical solutions, such as built up 3D structures. The simulations have produced informative visualizations of the guided wave modes in the structures as well as mimicking directly the output from sensors placed in the simulation space for direct comparison to experiments. Results from both drydock and in-water experiments with dummy mines are also shown.

Factors affecting fecal egg counts in periparturient Katahdin ewes and their lambs.

PubMed

Notter, D R; Burke, J M; Miller, J E; Morgan, J L M

2017-01-01

Selection for low fecal egg counts (FEC) can be used to genetically enhance resistance to gastrointestinal nematode parasites in growing lambs, thereby reducing the frequency of use of anthelmintics, facilitating marketing of organic lamb, and reducing the risk of development of anthelmintic resistance by the parasite. Recording of FEC in lambs has, therefore, been incorporated into several national sheep genetic evaluation programs. Ewes in late gestation and early lactation are also vulnerable to parasite infection and commonly experience a periparturient rise in FEC. This study was designed to assess factors associated with the periparturient rise in FEC in Katahdin ewes and associated changes in FEC in their lambs. Data came from 1,487 lambings by 931 Katahdin ewes from 11 farms in the Eastern United States. Fecal egg counts were measured in ewes at approximately 0, 30, and 60 d postpartum and in their lambs at approximately 60, 90, and 120 d of age. Approximately 1,400 lambs were evaluated at each measurement age. Data were analyzed separately for ewes and lambs and also initially analyzed separately for each measurement time. Repeated-measures analyses were then used to evaluate responses across measurement times. In ewes, FEC peaked at approximately 28 d postpartum, and we concluded that informative periparturient FEC could be obtained from 1 wk before until approximately 5 wk after lambing. Yearling ewes had higher FEC than adult ewes ( < 0.01), and ewes that nursed twin or triplet lambs had higher FEC than ewes that nursed single lambs ( < 0.01). In lambs, FEC increased through approximately 120 d of age. Lambs from yearling ewes and lambs nursed in larger litters were, like their dams, at greater risk of parasitism ( < 0.05). Ewes and lambs in these groups would benefit from enhanced monitoring of parasite loads at lambing and in early lactation. Correlations () between FEC in lambs at 90 d of age and FEC in ewes at 0, 30, and 60 d postpartum of 0.05 to 0.09 ( ≤ 0.05) support the presence of a genetic relationship between these 2 indicators of parasite resistance.

Vaginocervical stimulation of Ewes induces the rapid formation of a new bond with an alien young without interfering with a previous bond.

PubMed

Lévy, F; Keller, M; Cornilleau, F; Moussu, C; Ferreira, G

2010-09-01

Ewes form a selective olfactory memory for their lambs after 2 hr of mother-young interaction following parturition. Mothers will subsequently reject any strange lamb at suckling. The present study investigated whether artificial vaginocervical stimulation (VCS) allows the formation of a selective bond with an unfamiliar lamb and whether it interferes with the maintenance of the bond formed with the familiar lamb. At 2 hr postpartum, mothers were separated from their familiar lamb after having formed a selective bond with it and were given 10 min of mechanical VCS. In the "VCS + lamb" group (n = 24) an unfamiliar lamb was left with the ewe for 2 hr whereas in the "VCS no lamb" group (n = 26) the mother was left alone for the same period of time. Ewes of the "no VCS" group (n = 14) did not receive any VCS. In the majority of animals of the "VCS + lamb" group (23/24) VCS induced a complete acceptance of the unfamiliar lamb without any disruption of the bond previously formed with the familiar lamb. VCS or 2 hr of separation did not disrupt the maintenance of the selective bond initially formed with the familiar lamb since all the ewes of the "VCS no lamb" and "no VCS" groups accepted it at suckling.

7 CFR 65.190 - Lamb.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Lamb. 65.190 Section 65.190 Agriculture Regulations of..., PORK, LAMB, CHICKEN, GOAT MEAT, PERISHABLE AGRICULTURAL COMMODITIES, MACADAMIA NUTS, PECANS, PEANUTS, AND GINSENG General Provisions Definitions § 65.190 Lamb. Lamb means meat produced from sheep. ...

7 CFR 1280.402 - Assessments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND... producer, feeder, or seedstock producer shares the proceeds received for the lamb or lamb products sold..., or livestock market in the business of receiving lambs or lamb products for sale on commission for or...

7 CFR 1280.217 - Lamb purchases.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Lamb purchases. 1280.217 Section 1280.217 Agriculture... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Assessments § 1280.217 Lamb purchases. (a...

Establishment and development of ruminal hydrogenotrophs in methanogen-free lambs.

PubMed

Fonty, Gérard; Joblin, Keith; Chavarot, Michel; Roux, Remy; Naylor, Graham; Michallon, Fabien

2007-10-01

The aim of this work was to determine whether reductive acetogenesis can provide an alternative to methanogenesis in the rumen. Gnotobiotic lambs were inoculated with a functional rumen microbiota lacking methanogens and reared to maturity on a fibrous diet. Lambs with a methanogen-free rumen grew well, and the feed intake and ruminal volatile fatty acid concentrations for lambs lacking ruminal methanogens were lower but not markedly dissimilar from those for conventional lambs reared on the same diet. A high population density (10(7) to 10(8) cells g(-1)) of ruminal acetogens slowly developed in methanogen-free lambs. Sulfate- and fumarate-reducing bacteria were present, but their population densities were highly variable. In methanogen-free lambs, the hydrogen capture from fermentation was low (28 to 46%) in comparison with that in lambs containing ruminal methanogens (>90%). Reductive acetogenesis was not a significant part of ruminal fermentation in conventional lambs but contributed 21 to 25% to the fermentation in methanogen-free meroxenic animals. Ruminal H(2) utilization was lower in lambs lacking ruminal methanogens, but when a methanogen-free lamb was inoculated with a methanogen, the ruminal H(2) utilization was similar to that in conventional lambs. H(2) utilization in lambs containing a normal ruminal microflora was age dependent and increased with the animal age. The animal age effect was less marked in lambs lacking ruminal methanogens. Addition of fumarate to rumen contents from methanogen-free lambs increased H(2) utilization. These findings provide the first evidence from animal studies that reductive acetogens can sustain a functional rumen and replace methanogens as a sink for H(2) in the rumen.

A multi-feature integration method for fatigue crack detection and crack length estimation in riveted lap joints using Lamb waves

NASA Astrophysics Data System (ADS)

He, Jingjing; Guan, Xuefei; Peng, Tishun; Liu, Yongming; Saxena, Abhinav; Celaya, Jose; Goebel, Kai

2013-10-01

This paper presents an experimental study of damage detection and quantification in riveted lap joints. Embedded lead zirconate titanate piezoelectric (PZT) ceramic wafer-type sensors are employed to perform in situ non-destructive evaluation (NDE) during fatigue cyclical loading. PZT wafers are used to monitor the wave reflection from the boundaries of the fatigue crack at the edge of bolt joints. The group velocity of the guided wave is calculated to select a proper time window in which the received signal contains the damage information. It is found that the fatigue crack lengths are correlated with three main features of the signal, i.e., correlation coefficient, amplitude change, and phase change. It was also observed that a single feature cannot be used to quantify the damage among different specimens since a considerable variability was observed in the response from different specimens. A multi-feature integration method based on a second-order multivariate regression analysis is proposed for the prediction of fatigue crack lengths using sensor measurements. The model parameters are obtained using training datasets from five specimens. The effectiveness of the proposed methodology is demonstrated using several lap joint specimens from different manufactures and under different loading conditions.

Evaluation of Rambouillet, Polypay, and Romanov-White Dorper × Rambouillet ewes mated to terminal sires in an extensive rangeland production system: Lamb production.

PubMed

Notter, D R; Mousel, M R; Lewis, G S; Leymaster, K A; Taylor, J B

2017-09-01

Ewe productivity (i.e., total number or weight of lambs weaned per breeding ewe) is a key indicator of lamb production efficiency. This study compared various measures of ewe productivity and ewe and lamb performance among ewes of 3 breed types mated to rams of 4 terminal-sire breed types in an extensive rangeland production system. Purebred Rambouillet ( = 212), purebred Polypay ( = 236), and crossbred Romanov-White Dorper × Rambouillet (RW-RA; = 231) ewes were produced from locally adapted Polypay and Rambouillet ewes and then annually mated to Columbia, Suffolk, Columbia × Suffolk, or Suffolk × Columbia sires for up to 4 yr, beginning at 1 yr of age. The cumulative number and weight of lambs weaned through 4 yr were greater for RW-RA (5.9 lambs and 153 kg, respectively) and Polypay ewes (4.9 lambs and 123 kg, respectively) than for Rambouillet ewes (2.9 lambs and 99 kg, respectively) and also were greater for RW-RA ewes than for Polypay ewes (all < 0.001). Greater productivity of RW-RA and Polypay ewes, compared with Rambouillet ewes, was driven by greater lambing rates (ewes lambing per ewe exposed) as ewe lambs (87 and 77 vs. 31%, respectively; < 0.001) and greater ( < 0.001) litter sizes as ewe lambs (1.3, 1.3, and 1.0, respectively) and adult ewes (2.1, 2.0, and 1.6, respectively). The RW-RA ewes also had greater longevity ( < 0.01) and cumulative lambing rates ( < 0.001) than Polypay and Rambouillet ewes. Lamb BW at birth and weaning in adult ewes favored less-prolific Rambouillet ewes ( < 0.001), but after adjustment for type of birth and rearing and weaning age, differences in weaning BW among ewe breed types were small and not significant ( = 0.08). Effects of sire breed type on measures of cumulative ewe productivity were not significant ( > 0.74), but Suffolk-sired lambs had the heaviest adjusted birth weights ( = 0.01) and Columbia-sired lambs tended to have the lightest adjusted weaning weights ( = 0.12). Combined effects of heterosis and additive breed effects were associated with greater lambing rates in ewe lambs, larger litters at all ages, and substantially greater number and weight of lambs weaned for Polypay and RW-RA ewes than for Rambouillet ewes.

Comparison of two long acting pre-lambing anthelmintic treatments on the productivity of ewes in low body condition.

PubMed

Bingham, C; Hodge, A; Mariadass, B

2017-05-01

To determine if there was a benefit from treating ewes with a low body condition score (BCS) with long acting anthelmintic products pre-lambing and to compare the effects of two commonly used treatment options. The study was conducted on a single commercial hill country sheep and beef property in the central North Island of New Zealand. Mixed age twin-bearing ewes were preselected by the farmer as being in poor condition 4 weeks before the planned start of lambing, and were sequentially drafted into three equal groups identified with coloured ear tags. The negative control group (n=199) received no anthelmintic treatment; the other two groups received either a controlled release capsule (CRC) containing abamectin, albendazole, Se and Co (n=200) or a long-acting injection of moxidectin (n=200). All ewes were body condition scored (1-5 scale) and weighed at pre-lambing, docking (65 days after treatment) and at weaning (127 days after treatment). Faecal nematode egg counts (FEC) were carried out on 10 ewes from each group at these three times. Most lambs were matched to the ewe treatment groups at weaning, and weighed. At weaning the mean body weight of ewes treated with moxidectin was 3.2 (95% CI=2.3-4.3) kg heavier than controls, and of ewes treated with CRC was 3.6 (95% CI=2.5-4.5) kg heavier than control ewes (p<0.001). At the start of the trial only 61/599 (10.2%) ewes had a BCS≥3. At weaning, more ewes treated with CRC (140/194; 72%) or moxidectin (122/187; 65%) had a BCS≥3 than control ewes (55/179 (31%); p<0.001). In lambs that were matched with ewes from the treatment groups, the mean weight at weaning of lambs from ewes treated with moxidectin was 2.6 (95% CI=1.9-3.3) kg heavier, and from ewes treated with CRC was 2.6 (95% CI=1.9-3.4) kg heavier than lambs from control ewes (p<0.001). Treating twin-bearing ewes with low BCS pre-lambing with long acting anthelmintic treatments (moxidectin long acting injection or CRC) resulted in an increase in mean body weight of the ewes and lambs at weaning. There were no significant differences between the two pre-lambing treatments used. These results were based on a single property and thus cannot be generalised to all properties where management conditions and parasite populations may differ.

Intake, digestibility, nitrogen balance, performance, and carcass yield of lambs fed licuri cake.

PubMed

Costa, J B; Oliveira, R L; Silva, T M; Ribeiro, R D X; Silva, A M; Leão, A G; Bezerra, L R; Rocha, T C

2016-07-01

This study aimed to determine the impact of the inclusion of licuri cake in the diets of crossbred Santa Inês lambs, based on intake, digestibility, N balance, urea N, and performance. We used 44 male lambs that were vaccinated and wormed, with an average age of 6 mo and an average BW of 21.2 kg ± 2.7 kg. The lambs were fed a mixture of Tifton-85 hay (40%) and a concentrated mixture (60%) composed of ground corn, soybean meal, and mineral premix. For the treatments, licuri cake was added at levels of 0, 8, 16, and 24% of DM, with the licuri cake replacing soybean meal and ground corn. We used 11 lambs per treatment in a randomized design. The lambs were confined for 70 d, and the digestibility trial occurred between Day 40 and Day 55. The increased level of licuri cake inclusion promoted a linear reduction in DM intake ( = 0.00) with a 39% reduction between treatments with the 0 and 24% cakes. On the other hand, ether extract () consumption showed an initial quadratic increase ( = 0.00). The total weight gain and ADG showed a linear decrease ( = 0.00) with the addition of licuri cake. The inclusion of licuri cake linearly enhanced ( = 0.02) the digestibility of CP and EE, whereas the digestibility of other nutrients in lambs remained unchanged ( > 0.05). The licuri cake increase led to a linear decrease ( < 0.05) in the N intake, fecal N, and retained N in lambs. Urinary N was not changed. The slaughter carcass weight, HCW, cold carcass weight, hot carcass yield, and cold carcass yield showed linear decreases ( < 0.05) with the addition of licuri cake. Carcass morphometric measurements were influenced by experimental diets, showing linear decreases ( < 0.05) with the addition of licuri cake to diets. The fat thickness, conformation, external length, internal length, leg length, rump width, and chest circumference showed linear decreases ( < 0.05) with the inclusion of licuri cake in diets. The inclusion of licuri cake decreased DMI and digestibility, reflecting the lower ADG. Although feed efficiency was not affected, the lambs weighed less at slaughter and the licuri cake had a negative impact on carcass yield. Therefore, the use of the studied levels of licuri cake in diets for finishing lambs cannot be recommended.

Comparison of conventional and organic management conditions on growth performance, carcass characteristics and haematological parameters in Karacabey Merino and Kivircik breeds.

PubMed

Soysal, Deniz; Cibik, Recep; Aydin, Cenk; Ak, İbrahim

2011-04-01

Growth performance, carcass characteristics, post-slaughtering and haematological parameters of Kivircik and Karacabey Merino male lambs in conventional and organic management systems were compared. The animals which were weaned at 7 weeks of age were divided into Kivircik conventional, Kivircik organic (KO), Karacabey Merino conventional and Karacabey Merino organic (MO) groups containing 12 lambs each. Fattening was ended when lambs attained 35 kg of live weight. The time to attain the determined fattening weight was significantly different among the groups, and Merino lambs having higher live weight gain were earlier than Kivircik lambs (p < 0.05). Overall conventional (CG) and organic group lambs were also compared. Live weight gain, intra-abdominal fat amount, external fat thickness and visceral organ weight were significantly higher in CG lambs (p < 0.05). Higher haematocrit and erythrocyte counts were obtained with the CG group (p < 0.05), whilst triglyceride, total plasma cholesterol and lipoprotein (HDL, LDL, VLDL) levels between groups were not significant. Pneumonia was the unique infection, with an incidence of 50% (six lambs) and 16.6% (two lambs) for MO and KO animals, respectively. The mortality rate was 16.6% (two lambs) for MO group, whilst no mortality was recorded for KO group animals. The present study has shown that although Karacabey merino lambs had higher growth performance compared to Kivircik lambs, organically fattened lambs in whole exhibited inferior growth performance. Lower infection and mortality observed with Kivircik lambs suggested that they could be more resistant to infections and outdoor environmental conditions.

Advanced numerical technique for analysis of surface and bulk acoustic waves in resonators using periodic metal gratings

NASA Astrophysics Data System (ADS)

Naumenko, Natalya F.

2014-09-01

A numerical technique characterized by a unified approach for the analysis of different types of acoustic waves utilized in resonators in which a periodic metal grating is used for excitation and reflection of such waves is described. The combination of the Finite Element Method analysis of the electrode domain with the Spectral Domain Analysis (SDA) applied to the adjacent upper and lower semi-infinite regions, which may be multilayered and include air as a special case of a dielectric material, enables rigorous simulation of the admittance in resonators using surface acoustic waves, Love waves, plate modes including Lamb waves, Stonely waves, and other waves propagating along the interface between two media, and waves with transient structure between the mentioned types. The matrix formalism with improved convergence incorporated into SDA provides fast and robust simulation for multilayered structures with arbitrary thickness of each layer. The described technique is illustrated by a few examples of its application to various combinations of LiNbO3, isotropic silicon dioxide and silicon with a periodic array of Cu electrodes. The wave characteristics extracted from the admittance functions change continuously with the variation of the film and plate thicknesses over wide ranges, even when the wave nature changes. The transformation of the wave nature with the variation of the layer thicknesses is illustrated by diagrams and contour plots of the displacements calculated at resonant frequencies.

Sex-based differences in the adaptive value of social behavior contrasted against morphology and environment.

PubMed

Vander Wal, E; Festa-Bianchet, M; Réale, D; Coltman, D W; Pelletier, F

2015-03-01

The adaptive nature of sociality has long been a central question in ecology and evolution. However, the relative importance of social behavior for fitness, compared to morphology and environment, remains largely unknown. We assessed the importance of sociality for fitness (lamb production and survival) in a population of mark6d bighorn sheep (Ovis canadensis) over 16 years (n = 1022 sheep-years). We constructed social networks from observations (n = 38,350) of group membership (n = 3150 groups). We then tested whether consistent individual differences in social behavior (centrality) exist and evaluated their relative importance compared to factors known to affect fitness: mass, age, parental effects, and population density. Sheep exhibited consistent individual differences in social centrality. Controlling for maternal carryover effects and age, the positive effect of centrality in a social network on adult female lamb production and survival was equal or greater than the effect of body mass or population density. Social centrality had less effect on male survival and no effect on adult male lamb production or lamb survival. Through its effect on lamb production and survival, sociality in fission-fusion animal societies may ultimately influence population dynamics equally or more than morphological or environmental effects.

Stochasticity in the Expression of LamB and its Affect on λ phage Infection

NASA Astrophysics Data System (ADS)

Chapman, Emily; Wu, Xiao-Lun

2006-03-01

λ phage binds to E. Coli's lamB protein and injects its DNA into the cell. The phage quickly replicates and after a latent period the bacteria bursts, emitting mature phages. We developed a mathematical model based on the known physical events that occur when a λ phage infects an E.Coli cell. The results of these models predict that the bacteria and phage populations become extinct unless the parameters of the model are very finely tuned, which is untrue in the nature. The lamB protein is part of the maltose regulon and can be repressed to minimal levels when grown in the absence of inducer. Therefore, a cell that is not expressing any lamB protein at that moment is resistant against phage infection. We studied the dynamic relationship between λ phage and E. Coli when the concentration of phage greatly outnumbers the concentration of bacteria. We study how the stochasticity of the expression of lamB affects the percentage of cells that the λ phage infects. We show that even in the case when the maltose regulon is fully induced a percentage of cells continue to persist against phage infection.

The effects of diet and breed on the volatile compounds of cooked lamb.

PubMed

Elmore, J S; Mottram, D S; Enser, M; Wood, J D

2000-06-01

The effect of varying the n-3 polyunsaturated fatty acid (PUFA) composition of lamb muscle on the formation of aroma volatiles during cooking has been examined. The meat was obtained from four groups of Suffolk and Soay lambs fed different supplementary fats: a palm-oil based control; bruised whole linseed, which increased muscle levels of α-linolenic acid (C18:3 n-3); fish oil, which increased eicosapentaenoic acid (EPA, C20:5 n-3) and docosahexaenoic acid (DHA, C22:6 n-3); and equal quantities of linseed and fish oil (fat basis). Higher quantities of lipid oxidation products were found in the aroma volatiles of lamb muscle from animals fed fish oil, compared to the control. In particular, unsaturated aldehydes, unsaturated hydrocarbons and alkylfurans increased up to fourfold. These compounds derived from the autoxidation of PUFAs during cooking. Although some of these volatiles were increased in meat from animals fed the linseed supplement, the effect was not as great as with the fish oil fed lambs. Levels of volatiles derived from the Maillard reaction, such as pyrazines and sulfur compounds, were up to four times higher in Soays than Suffolks.

The effect of yeast (Saccharomyces cerevisiae) on nutrient intake, digestibility and finishing performance of lambs fed a diet based on dried molasses sugar beet-pulp.

PubMed

Payandeh, S; Kafilzadeh, F

2007-12-15

This experiment was conducted to determine the effect of yeast (Saccharomyces cerevisiae, SC47) on finishing performance, digestibility, some blood metabolites and carcass characteristics of male lambs fed a diet based on dried Molasses Sugar Beet-Pulp (MSBP). Eighteen Sanjabi male lambs (20.95 +/- 2.7 kg initial body weight and 3 month of age) were used in a completely randomized design. Animals were assigned to one of the two dietary treatments (with or without yeast). Digestibility and nitrogen balance experiment was carried out using six mature rams on finishing diet with and without yeast. Serum metabolites were determined in samples taken from lambs at the end of finishing period. Dry matter digestibility of finishing diet was significantly increased by yeast addition. However, yeast did not have any significant effect on apparent digestibility of OM, NDF, CP and energy. Nitrogen retention was also not affected by yeast addition. Yeast resulted in a significant increase in the average daily gain, dry matter and organic matter intake. However, feed conversion ratio was not significantly affected by addition of yeast. The concentration of the serum metabolites including glucose, urea, cholesterol, sodium, potassium, calcium, phosphorous and cratinine were not affected significantly by yeast supplementation, but triglyceride concentrations increased significantly when yeast was fed. Addition of yeast to the diet did not have any significant effect on the carcass characteristics. Results of this study suggest that feeding saccharomyces cerevisiae with a diet based on MSBP can improve the performance of fattening lambs without any change in carcass characteristics or cuts.

A national audit of retail lamb loin quality in Australia.

PubMed

Safari, E; Channon, H A; Hopkins, D L; Hall, D G; van de Ven, R

2002-07-01

A retail audit of lamb loin tenderness was conducted over a 12-month period to determine the variation in tenderness of Australian lamb. Tenderness was objectively measured using Warner-Bratzler (WB) shear force. Muscle pH and cooking loss were determined on all samples and colour was measured on a sub-sample of loins. A total of 909 midloins from retail butcher shops and supermarkets located in four Australian capital cities (Sydney, Canberra, Melbourne, and Perth) were evaluated at four sampling times (December 1997 and March, June, and October 1998). Overall, 20.3% of all midloins purchased had a WB shear force value above the threshold level of 5 kg. Generic samples from Melbourne butcher shops were similar for WB shear force on average to the generic samples from Canberra and Sydney, whereas those from Melbourne supermarkets had significantly (P<0.001) higher WB shear force and were in line with generic samples from Perth. In both Canberra and Perth, alliance (branded) lamb had a greater WB shear force (P<0.05) than generic lamb. No relationship was found between price per kg and shear force (r=0.02) for loins purchased in Sydney (n=220). Price per kg differed between months (P<0.001) and suburbs (P<0.001), but not between retail butcher shops and supermarkets. Of the midloins tested, 10.3% had a pH above the critical point of 5.8. Midloins from the December 1997 sampling had a lower pH (P<0.01) than those sampled at other months. Those sampled in Melbourne and Perth had a similar mean pH, which were lower (P<0.001) than Canberra and Sydney samples. The findings from this quality audit suggest that there is room to improve the tenderness of Australian lamb sold in the domestic market. A lamb eating quality assurance system, based on set protocols, is one approach that is currently being investigated in Australia to ensure the supply of consistently high eating quality lamb to consumers.

Structural health monitoring of plates with surface features using guided ultrasonic waves

NASA Astrophysics Data System (ADS)

Fromme, P.

2009-03-01

Distributed array systems for guided ultrasonic waves offer an efficient way for the long-term monitoring of the structural integrity of large plate-like structures. The measurement concept involving baseline subtraction has been demonstrated under laboratory conditions. For the application to real technical structures it needs to be shown that the methodology works equally well in the presence of structural and surface features. Problems employing this structural health monitoring concept can occur due to the presence of additional changes in the signal reflected at undamaged parts of the structure. The influence of the signal processing parameters and transducer placement on the damage detection and localization accuracy is discussed. The use of permanently attached, distributed sensors for the A0 Lamb wave mode has been investigated. Results are presented using experimental data obtained from laboratory measurements and Finite Element simulated signals for a large steel plate with a welded stiffener.

15 CFR 2014.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... TRADE REPRESENTATIVE IMPLEMENTATION OF TARIFF-RATE QUOTA FOR IMPORTS OF LAMB MEAT § 2014.2 Definitions... meanings assigned as follows: (a) Lamb meat means fresh, chilled, or frozen lamb meat, provided for in...-quota lamb meat means lamb meat that is entered under the in-quota rate of duty. (c) Participating...

7 CFR 59.302 - Mandatory weekly reporting for lambs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Mandatory weekly reporting for lambs. 59.302 Section... (CONTINUED) LIVESTOCK MANDATORY REPORTING Lamb Reporting § 59.302 Mandatory weekly reporting for lambs. (a... domestic from imported market purchases: (1) The quantity of lambs purchased through a negotiated purchase...

Genetic parameters for ewe reproductive performance and peri-parturient fecal egg counts and their genetic relationships with lamb body weights and fecal egg counts in Katahdin sheep

USDA-ARS?s Scientific Manuscript database

Genetic parameters for ewe reproductive traits [number of lambs born (NLB) and number of lambs weaned (NLW)] and ewe peri-parturient rise (PPR) fecal egg counts (FEC) at lambing (PPR0) and at 30-d post lambing (PPR30), and their genetic relationships with lamb BW and FEC in Katahdin sheep were estim...

The Effect of Two Different Oxytetracycline Treatments in Experimental Ehrlichia phagocytophila Infected Lambs

PubMed Central

Stuen, S; Bergström, K

2001-01-01

The effect of 2 different oxytetracycline treatments in acute E. phagocytophila infected lambs was investigated. Twenty 5-month-old lambs of the Dala and Rygja breeds were used. Ten lambs were inoculated intravenously with a stabilate of an ovine E. phagocytophila strain. On the third day of fever, 4 lambs were given long-acting oxytetracycline (Terramycin prolongatum vet®, Pfizer) (20 mg/kg) intramuscularly and another 4 lambs were given short-acting oxytetracycline (Terramycin vet®, Pfizer) (10 mg/kg) intravenously for 5 consecutive days. The lambs were examined for the presence of Ehrlichia infection by blood smear evaluation, polymerase chain reaction (PCR) and antibody titre against E. equi. One month after the last antibiotic treatment, 250 ml citrate blood from each of these lambs were inoculated into each of 10 susceptible lambs, which were observed during the following 6 weeks. The results indicate that oxytetracycline given in the acute stage of the infection may effectively teminate the development of fever, rickettsemia and weight reduction in E. phagocytophila infected lambs. No difference was observed between the 2 treatment groups. However, at least 3 of 8 antibiotic treated lambs (37.5%) were still infected with granulocytic Ehrlichia 3 months after treatment. PMID:11887394

Importance of birthcoat for lamb survival and growth in the Romane sheep breed extensively managed on rangelands.

PubMed

Allain, D; Foulquié, D; Autran, P; Francois, D; Bouix, J

2014-01-01

The Romane sheep breed proved to be adapted to harsh conditions with high prolificacy and lamb survival in outdoor farming, even under bad climate conditions. This breed shows large variability in its fleece type at birth and it has been suggested that lamb survival could be related to birthcoat type. The aim of the present study was to: i) characterize the coat of the lamb at birth and quantify lamb survival in relation to the birthcoat type and its protective properties concerning heat loss in the Romane breed raised under permanent exposure outdoors from birth, and ii) estimate genetic parameters of birthcoat type in relation to lamb survival and live body weight. A total of 7,880 lambs from 104 sires and 1,664 dams were used in a 14-yr experiment. The pedigree file included 9,625 individuals over 15 generations. Birthcoat type, coat surface temperature, coat depth, lamb survival, and growth were measured from birth to weaning. Weather data (temperature, wind speed, relative humidity, and precipitation) were recorded daily during lambing time. Two types of coats were observed at birth: hairy coat (62.9% of lambs) with a long coat depth (average 23.3 mm) or woolly 1 (37.1% of lambs) with a short coat depth (average 8.3 mm). Birthcoat type was an important factor affecting lamb survival and growth from birth in the Romane breed. Total mortality rate was significantly less in hairy-bearing coat lambs than in short-woolly coat ones: 7.0% vs. 9.6%, 11.6 % vs. 14.8%, and 15.7 % vs. 20.1 % at 2, 10, and 50 d, respectively, and the relative risks of death increased by 37%, 67%, and 46 % at 2, 10, and 50 d of age, respectively, in short-woolly lambs. At birth, a significant lower coat surface temperature, indicating less heat loss, was observed in long-hairy coat lambs compared with others (21.1°C vs. 26.1°C). Heavier body weights and better growth performances up to the age of 50 d were observed in long-hairy-bearing coat lambs. Lamb survival was positively correlated to weather conditions at lambing time in short-woolly lambs, whereas no relation was observed in hairy-coat lambs. Heritability estimate of birthcoat type (hairy or woolly) is high (0.88). Genetic correlations between birthcoat type, lamb survival, and live body weight at birth were positive and moderate, suggesting that it would be beneficial to take birthcoat into account as an adaptive trait in any genetic strategies for sheep production in harsh conditions on rangelands.

Acoustic black holes: recent developments in the theory and applications.

PubMed

Krylov, Victor

2014-08-01

Acoustic black holes are relatively new physical objects that have been introduced and investigated mainly during the last decade. They can absorb almost 100% of the incident wave energy, and this makes them very attractive for such traditional engineering applications as vibration damping in different engineering structures and sound absorption in gases and liquids. They also could be useful for some ultrasonic devices using Lamb wave propagation to provide anechoic termination for such waves. So far, acoustic black holes have been investigated mainly for flexural waves in thin plates, for which the required gradual changes in local wave velocity with distance can be easily achieved by changing the plates' local thickness. The present paper provides a brief review of the theory of acoustic black holes, including their comparison with optic black holes introduced about five years ago. Review is also given of the recent experimental work carried out at Loughborough University on damping structural vibrations using the acoustic black hole effect. This is followed by the discussion on potential applications of the acoustic black hole effect for sound absorption in air.

Nonlinear guided wave propagation in prestressed plates.

PubMed

Pau, Annamaria; Lanza di Scalea, Francesco

2015-03-01

The measurement of stress in a structure presents considerable interest in many fields of engineering. In this paper, the diagnostic potential of nonlinear elastic guided waves in a prestressed plate is investigated. To do so, an analytical model is formulated accounting for different aspects involved in the phenomenon. The fact that the initial strains can be finite is considered using the Green Lagrange strain tensor, and initial and final configurations are not merged, as it would be assumed in the infinitesimal strain theory. Moreover, an appropriate third-order expression of the strain energy of the hyperelastic body is adopted to account for the material nonlinearities. The model obtained enables to investigate both the linearized case, which gives the variation of phase and group velocity as a function of the initial stress, and the nonlinear case, involving second-harmonic generation as a function of the initial state of stress. The analysis is limited to Rayleigh-Lamb waves propagating in a plate. Three cases of initial prestress are considered, including prestress in the direction of the wave propagation, prestress orthogonal to the direction of wave propagation, and plane isotropic stress.

Tissue residue depletion of moxidectin in lambs (Ovis aries) following subcutaneous administration.

PubMed

Cruz, Michelle Del Bianchi A; Fernandes, Maria Ângela M; Monteiro, Alda Lúcia G; Teles, Juliana A; Anadón, Arturo; Reyes, Felix G R

2018-06-07

To date, a tissue depletion study of moxidectin (MOX) in lambs is not available. Thus, considering that lamb meat is of great commercial interest in the world, the aim of the present study was to determine the residue levels of MOX in lamb target-tissues (muscle, liver, kidney and fat) and subsequently calculate the MOX withdrawal period. For this purpose, the target-tissues were analysed by ultra-high-performance liquid chromatography-tandem mass spectrometry. Method validation was performed based on Commission Decision 2002/657/EC and VICH GL49. To quantify the analyte, matrix-matched analytical curves were constructed with spiked blank tissues. The limits of detection and quantitation were 1.5 and 5 ng g -1 , respectively, for all matrices. The linearity, decision limit, detection capability accuracy and inter- and intra-day precision of the method are reported. The lambs were treated with a single subcutaneous dose of 0.2 mg MOX kg -1 body weight and were slaughtered in accordance with accepted animal care protocols. Samples of target-tissues were collected on 2, 4, 7, 14, 28 and 42 days after MOX administration. During the whole study, the highest drug residue level occurred in the fat. For the other target-tissues (muscle, liver and kidney), MOX concentrations were below the maximum residue limit (MRL). Considering the MRL value of 500 µg kg -1 for MOX residues in sheep fat, our results in lambs allowed the estimation of a MOX withdrawal period of 31 days. This indicates that the withdrawal period established for MOX in adult sheep (28 days) does not apply for lambs.

Fast detection and visualization of minced lamb meat adulteration using NIR hyperspectral imaging and multivariate image analysis.

PubMed

Kamruzzaman, Mohammed; Sun, Da-Wen; ElMasry, Gamal; Allen, Paul

2013-01-15

Many studies have been carried out in developing non-destructive technologies for predicting meat adulteration, but there is still no endeavor for non-destructive detection and quantification of adulteration in minced lamb meat. The main goal of this study was to develop and optimize a rapid analytical technique based on near-infrared (NIR) hyperspectral imaging to detect the level of adulteration in minced lamb. Initial investigation was carried out using principal component analysis (PCA) to identify the most potential adulterate in minced lamb. Minced lamb meat samples were then adulterated with minced pork in the range 2-40% (w/w) at approximately 2% increments. Spectral data were used to develop a partial least squares regression (PLSR) model to predict the level of adulteration in minced lamb. Good prediction model was obtained using the whole spectral range (910-1700 nm) with a coefficient of determination (R(2)(cv)) of 0.99 and root-mean-square errors estimated by cross validation (RMSECV) of 1.37%. Four important wavelengths (940, 1067, 1144 and 1217 nm) were selected using weighted regression coefficients (Bw) and a multiple linear regression (MLR) model was then established using these important wavelengths to predict adulteration. The MLR model resulted in a coefficient of determination (R(2)(cv)) of 0.98 and RMSECV of 1.45%. The developed MLR model was then applied to each pixel in the image to obtain prediction maps to visualize the distribution of adulteration of the tested samples. The results demonstrated that the laborious and time-consuming tradition analytical techniques could be replaced by spectral data in order to provide rapid, low cost and non-destructive testing technique for adulterate detection in minced lamb meat. Copyright © 2012 Elsevier B.V. All rights reserved.

Buffel grass (Cenchrus ciliaria L.) substitution for orange pulp on intake, digestibility, and performance of hairsheep lambs.

PubMed

Macías-Cruz, Ulises; Quintero-Elisea, Juan A; Avendaño-Reyes, Leonel; Correa-Calderón, Abelardo; Alvarez-Valenzuela, Francisco D; Soto-Navarro, S A; Lucero-Magaña, F A; González-Reyna, Arnoldo

2010-02-01

Twenty Dorper x Pelibuey male lambs were used to evaluate the effect of substitution of forage with fresh orange pulp (FOP) in diets for fattening lambs on productive behavior, nutrient intake, apparent digestibility coefficient, and feeding costs. Lambs were divided into five groups (n = 4) and then housed in individual pens during 70 d. Treatments consisted of five levels of FOP (0, 25, 50, 75 and 100%) which substituted buffel grass hay on the base diet (40:60%, forage:concentrate). Additionally, changes in chemical composition of FOP stored in stack during 8 d were evaluated (from the day 1 until day 8). Daily feed intake expressed as kg/day and % live weight, lamb growth rate, feeding cost of each lamb per day and per fattening period, hemicellulose intake, and DM, OM, CP, NDF and hemicellulose digestibility showed a quadratic effect (P < 0.05), while DM, OM and CP intake presented a cubic effect (P < 0.05) with the increasing level of FOP. The maximum estimated value for those variables was observed at 75% of hay replacement with FOP. With respect to changes in chemical composition of pulp stored, DM content increased (P = 0.0011) from 210 to 310 g/kg FOP and OM, fiber fraction, and ash content were constant (P > 0.05) among storage days. Therefore, replacing around 75% of buffel grass hay with FOP in diets for fattening lambs resulted in the best growth rate and more efficient diet utilization. Fresh orange pulp stored in a stack did not change its chemical composition, and did not affect its utilization as a sheep feedstuff.

Improving the sensory and oxidative stability of cooked and chill-stored lamb using dietary rosemary diterpenes.

PubMed

Serrano, Rafael; Ortuño, Jordi; Bañón, Sancho

2014-09-01

Two dietary rosemary extracts (DREs) containing diterpenes (carnosic acid and carnosol at 1:1 and 2:1 w:w) were tested in fattening lambs to stabilize the sensory quality of cooked and chill-stored patties. A total of 63 lambs were fed freely for 80 ± 5 d with a basal diet supplemented or not with DRE. Minced leg meat from each lamb was used to make patty batches. The patties were cooked at 72 ºC for 2 min, aerobically packed, kept at 2 ºC for up to 4 d and then reheated. Sensory traits (color, odor, flavor, and texture), CIELab color, and lipid oxidation (assessed as TBARS) were determined. In a first experiment, the lamb diet was supplemented with 600 mg of 1:1-DRE or 2:1-DRE kg(-1) feed. The 1:1-DRE diet delayed discoloration, flavor deterioration, and rancidity, while the 2:1-DRE diet was ineffective in this respect. In a second experiment, 4 supplementation levels of 1:1-DRE (0, 200, 400, and 600 mg kg(-1) feed) were compared. Flavor deterioration was delayed when the lamb diet was supplemented with at least 400 mg 1:1-DRE kg(-1) feed. The effects of the diet on the odor, flavor, and color were corroborated by differences in TBARS and CIELab. The results obtained suggest that rosemary diterpenes and/or their active secondary compounds deposited in muscle can act as endogenous antioxidants in cooked lamb. The carnosol intake seems crucial in the antioxidant actions achieved through DRE. The use of rosemary antioxidants in animal feeding would allow meat-based dishes to be preserved longer without adding preservatives. © 2014 Institute of Food Technologists®

The effects of feeding clinoptilolite on hematology, performance, and health of newborn lambs.

PubMed

Norouzian, M A; Valizadeh, R; Khadem, A A; Afzalzadeh, A; Nabipour, A

2010-11-01

The effects of feeding clinoptilolite on hematology, performance, and health of newborn Balouchi lambs were evaluated in this experiment. In a completely randomized design, 30 newborn lambs were allocated to three groups and fed by basal diet (C0; without clinoptilolite) and C1 and C2 (the basal diet plus 1.5% and 3% clinoptilolite, respectively, for 6 weeks (3 weeks before and 3 weeks after weaning)). Blood samples were taken from all lambs, at the time when the animals were allocated to the experimental diet and at the end of each week of experiment, and analyzed for hematology, plasma fibrinogen, and total protein. Performance and health of all lambs were measured. Fecal consistency score and diarrhea severity were evaluated. There was no difference between lambs in case of hematological parameters. Lambs fecal consistency score and severity of diarrhea were lowest (P < 0.05) for lambs on C1 and C2 and highest for lambs on C0. Dry matter intake and feed conservation ratio were similar between the groups of lambs fed by different diets, but daily gain of lambs differed significantly (P < 0.05) and was higher in C2. It was concluded that addition of 3% clinoptilolite to starter diet of newborn lamb can reduce incidence and severity of diarrhea, although its effect on hematology and performance was negligible.

7 CFR 59.301 - Mandatory Daily Reporting for Lambs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Mandatory Daily Reporting for Lambs. 59.301 Section 59... (CONTINUED) LIVESTOCK MANDATORY REPORTING Lamb Reporting § 59.301 Mandatory Daily Reporting for Lambs. (a) In... prices for lambs (per hundredweight) established on that day as F.O.B. feedlot or delivered at the plant...

The duration of passive protection against Taenia ovis larvae in lambs.

PubMed

Heath, D D; Yong, W K; Osborn, P J; Parmeter, S N; Lawrence, S B; Twaalfhoven, H

1979-10-01

In an attempt to induce passive protection in lambs against Taenia ovis larvae that would last for the 15-20 weeks from birth to slaughter as fat lambs, one group of ewes was immunized by a series of injections of 2000, 4000, 8000, 16 000 and 32 000 activated oncospheres of Taenia ovis prior to parturition. Another group of ewes was not immunized. All ewes had previously grazed pasture lightly infected with T. ovis eggs. Most lambs from non-immunized ewes developed cysts after oral infection with T. ovis eggs. However, no lambs from immunized ewes developed cysts up to and including 6 weeks after birth. Between 8 and 16 weeks after birth a proportion of lambs were found to be susceptible to infection. By 18 weeks after birth all lambs were apparently susceptible. The 99% confidence band for the mean duration of demonstrable complement-fixing antibody titres was 6.2-7.8 weeks for lambs from immunized ewes. The persistence of maternal protective antibody in some lambs could possibly preclude successful active immunization of all lambs against T. ovis larvae before 18 weeks of age.

Evaluation of Columbia, USMARC-Composite, Suffolk, and Texel rams as terminal sires in an extensive rangeland production system: IV. Postfabrication carcass component weights.

PubMed

Mousel, M R; Notter, D R; Leeds, T D; Zerby, H N; Moeller, S J; Lewis, G S

2013-05-01

Postfabrication carcass component weights of 517 crossbred wether lambs were analyzed to evaluate 4 terminal-sire breeds. Wethers were produced over 3 yr from single-sire matings of 22 Columbia, 22 USMARC-Composite (Composite), 21 Suffolk, and 17 Texel rams to adult Rambouillet ewes. Lambs were reared to weaning in an extensive western rangeland production system and finished in a feedlot on a high-energy finishing diet. When wethers reached a mean BW of 54.4, 61.2, or 68.0 kg, they were transported to The Ohio State University abattoir for harvest. After refrigeration for approximately 24 h, chilled carcass weight (CCW) was measured, carcasses were fabricated according to Style A of Institutional Meat Purchase Specifications, and postfabrication weights were recorded. At comparable numbers of days on feed, Suffolk-sired lambs had heavier (P < 0.04) neck, breast, shoulder, foreshank, rack, loin, leg, sirloin, roast-ready rack, trimmed loin, and boneless leg cuts than progeny of the other sire breeds. Boneless sirloins were heavier (P < 0.01) for Suffolk-sired than Composite-sired lambs but did not differ from those for Columbia- or Texel-sired lambs. Columbia- and Suffolk-sired lambs had heavier (P < 0.01) hindshanks than Texel-sired lambs. Suffolk-sired lambs had heavier (P < 0.01) high-value cuts (rack, loin, leg, and sirloin) and trimmed high-value cuts than progeny of the other sire breeds. Cutting loss (CCW - wholesale cut weights) and high-value trimming loss were greatest (P < 0.02) for Suffolk-sired lambs and least for Texel- and Composite-sired lambs. Sire breed did not affect (P > 0.06) flank weight. Data adjusted to comparable CCW reduced the number of significant sire-breed effects and changed sire-breed rankings of carcass component weights, for which sire breeds differed. After adjusting, Suffolk-sired lambs had lighter (P < 0.05) loins than Columbia- and Composite-sired lambs, Composite-sired lambs had heavier (P < 0.05) high-value cuts than Suffolk-sired lambs, and Suffolk- and Columbia-sired lambs had heavier (P < 0.05) necks than Texel-sired lambs. At predicted backfat thickness of 6.6 mm, Composite-sired lambs had a greater (P < 0.05) percentage of high-value cuts than Suffolk-sired lambs before but not after trimming. Producers can use these results to select terminal-sire breeds that will complement their production system and improve lamb value.

Influence of Nigella sativa seeds, Rosmarinus officinalis leaves and their combination on growth performance, immune response and rumen metabolism in Dorper lambs.

PubMed

Odhaib, Kifah Jumaah; Adeyemi, Kazeem Dauda; Ahmed, Muideen Adewale; Jahromi, Muhammad Faseleh; Jusoh, Shokri; Samsudin, Anjas Asmara; Alimon, Abdul Razak; Yaakub, Halimatun; Sazili, Awis Qurni

2018-06-01

The objective of this study was to determine the effects of dietary supplementation of Nigella sativa L. seeds, Rosmarinus officinalis L. leaves and their combination on rumen metabolism, nutrient intake and digestibility, growth performance, immune response and blood metabolites in Dorper lambs. Twenty-four entire male Dorper lambs (18.68 ± 0.6 kg, 4-5 months old) were randomly assigned to a concentrate mixture containing on a dry matter basis either, no supplement (control, T1), 1% R. officinalis leaves (T2), 1% N. sativa seeds (T3) or 1% R. officinalis leaves +1% N. sativa seeds (T4). The lambs had ad libitum access to urea-treated rice straw (UTRS) and were raised for 90 days. Supplemented lambs had greater (P < 0.05) intake of DM and UTRS than the control lambs. The T4 lambs had lower (P < 0.05) nutrient digestibility than those fed other treatments. Total and daily weight gain was greater (P < 0.05) in T2 lambs than those fed other diets. The T3 and T4 lambs had greater (P < 0.05) ruminal pH than the T1 and T2 lambs. Supplemented lambs had lower (P < 0.05) ruminal total volatile fatty acids, acetate, propionate, NH 3 -N and C18:0 than the control lambs. The T4 lambs had lower (P < 0.05) population of Fibrobacter succinogenes, Ruminococcus albus, methanogens and total protozoa compared with those fed other diets. Supplemented lambs had lower (P < 0.05) neutrophils, basophils and serum urea and greater (P < 0.05) serum IgA and IgG compared with the control lambs. The current results emphasised the variation in the efficacy of medicinal plants in ruminant nutrition.

Ewes Direct Most Maternal Attention towards Lambs that Show the Greatest Pain-Related Behavioural Responses

PubMed Central

Futro, Agnieszka; Masłowska, Katarzyna; Dwyer, Cathy M.

2015-01-01

Although neonatal farm animals are frequently subjected to painful management procedures, the role of maternal behaviour in pain coping, has not been much studied. We investigated whether ewes were able to distinguish between lambs in pain and those that were not, and whether their behaviour altered depending on the severity of lamb pain. Eighty male lambs were allocated to one of 4 pain treatments within 24 hours of birth. Lambs were either handled only (C), bilaterally castrated with tight rubber rings (RR), as for RR but with the application of a Burdizzo clamp immediately proximal to the ring (Combined) or subjected to short scrotum castration (SSC) where the testicles were retained within the abdomen and only the scrotum removed. The behaviour of the ewe, treated lamb and untreated sibling where present (n = 54) were recorded for 30 minutes after treatment. Castration treatment increased the expression of abnormal standing and lying postures, specific pain-related behaviours (head-turning, stamping/kicking, easing quarters, tail wagging) and composite pain scores (P<0.001 for all). The greatest expression of pain-related behaviours was shown by lambs in the RR group, which were the only group to show rolling responses indicative of severe pain, followed by the SSC group. Ewes expressed more licking/sniffing responses to the RR and SSC lambs than towards the Combined and C lambs (P<0.05), and oriented most to RR lambs and least to C lambs (P<0.001). Ewes with two lambs also directed more attention towards the treated than the untreated lamb (P<0.001). The quantity of maternal care directed towards the lamb was positively correlated with the expression of active pain behaviours. The data demonstrate that ewes are able to discriminate between lambs in pain and those that are not, and that their response is increased with a greater severity of pain. PMID:26217942

Evaluation of oxidative stability of lamb burger with Origanum vulgare extract.

PubMed

Fernandes, R P P; Trindade, M A; Tonin, F G; Pugine, S M P; Lima, C G; Lorenzo, J M; de Melo, M P

2017-10-15

The objective was to evaluate replacement of sodium erythorbate with a natural antioxidant (oregano extract) on physicochemical and sensory stability of lamb burgers, and determine the appropriate amount. Five treatments were prepared, including control (without antioxidant), sodium erythorbate, and three concentrations of oregano extract (13.32, 17.79 and 24.01mL/kg), based on antioxidant capacity determined using the Folin-Ciocalteu, 2,2-diphenyl-1-picrylhydrazyl (DPPH) and ferric reducing antioxidant power (FRAP) methods, respectively. Burgers containing oregano extract, at the concentration determined by FRAP method, had higher oxidative stability, evidenced by an 80% reduction (P<0.001) in thiobarbituric acid reactive substances, effective inhibition of protein oxidation (P<0.01) and less colour loss during frozen storage. Oregano extract did not impair (P>0.05) consumers' sensory acceptance of the lamb burgers. Under the conditions tested, addition of 24mL/kg of oregano extract could be recommended as a natural antioxidant in lamb burgers. Copyright © 2017 Elsevier Ltd. All rights reserved.

The quality of meat from sheep treated with tannin- and saponin-based remedies as a natural strategy for parasite control.

PubMed

Brogna, D M R; Tansawat, R; Cornforth, D; Ward, R; Bella, M; Luciano, G; Priolo, A; Villalba, J

2014-02-01

Lambs were assigned to four groups of seven and treated as follows for 12 days: control group (BP) was fed beet pulp; group T (tannin remedy) received the BP diet including 80 g/kg of quebracho extract; group S (saponin remedy) received the BP diet including 15 g/kg of quillaja extract; and group C had a free choice between T and S remedies. Lipid oxidation was lower in meat from S lambs compared to T lambs (P<0.05). Among the volatile compounds, lactate was lower in meat from S lambs compared to T animals (P=0.05). Metabolomic analysis showed that the T treatment increased ribose, fructose, glucose and sorbitol concentration in meat (P<0.05), while cholesterol was decreased by S and C treatments. The T treatment increased the concentration of C14:1 cis-9 (P<0.05). These findings indicate that treatments for parasite control containing tannins and saponins do not detrimentally affect sheep meat quality. © 2013.

Impact of feeding saltbush twigs on feed intake, weight gain, and some mineral levels of fattening awassi lambs.

PubMed

Alazzeh, A Y; Abughazaleh, A A; Awawdeh, F T; Abdelrahman, M M; Al-Rayyan, N A

2009-07-01

This experiment was conducted to investigate the effect of the inclusion of saltbush (Atriplex sp.) on the productive performance and blood mineral profile of fattening lambs. Eighteen Awassi lambs, 70 +/- 3 days of age and 23 +/- 1.8 kg body weights, were randomly selected and divided into three equal groups. Lambs in group one (control) were offered 0.2 kg/day shredded straw of barley (tibin) as the sole source of roughage, while lambs in treatment groups 2 and 3 were provided either 0.2 kg/day Atriplex nummularia or Atriplex halimus as their sole roughage content for 10 weeks. All lambs were also provided 1.1 kg/day of concentrate ration. Although lambs fed A. halimus had significantly (P < 0.05) lower dry matter intake than the control group, the daily weight gain of the two groups of lambs were not significantly different (P > 0.05). Lambs fed either A. nummularia or A. halimus had significantly lower (P < 0.05) calcium and copper levels but significantly higher (P < 0.05) cobalt levels in their blood serum than the control group. Zinc blood serum level was not affected (P > 0.05) by the treatment diets. These results suggested that A. nummularia and A. halimus can substitute for barley straw in the ration of fattening Awassi lambs without compromising lambs weight gain; however, special attention should be given to the mineral status in lambs if saltbush is a major feed component for prolonged periods of time.

Dissipation-preserving spectral element method for damped seismic wave equations

NASA Astrophysics Data System (ADS)

Cai, Wenjun; Zhang, Huai; Wang, Yushun

2017-12-01

This article describes the extension of the conformal symplectic method to solve the damped acoustic wave equation and the elastic wave equations in the framework of the spectral element method. The conformal symplectic method is a variation of conventional symplectic methods to treat non-conservative time evolution problems, which has superior behaviors in long-time stability and dissipation preservation. To reveal the intrinsic dissipative properties of the model equations, we first reformulate the original systems in their equivalent conformal multi-symplectic structures and derive the corresponding conformal symplectic conservation laws. We thereafter separate each system into a conservative Hamiltonian system and a purely dissipative ordinary differential equation system. Based on the splitting methodology, we solve the two subsystems respectively. The dissipative one is cheaply solved by its analytic solution. While for the conservative system, we combine a fourth-order symplectic Nyström method in time and the spectral element method in space to cover the circumstances in realistic geological structures involving complex free-surface topography. The Strang composition method is adopted thereby to concatenate the corresponding two parts of solutions and generate the completed conformal symplectic method. A relative larger Courant number than that of the traditional Newmark scheme is found in the numerical experiments in conjunction with a spatial sampling of approximately 5 points per wavelength. A benchmark test for the damped acoustic wave equation validates the effectiveness of our proposed method in precisely capturing dissipation rate. The classical Lamb problem is used to demonstrate the ability of modeling Rayleigh wave in elastic wave propagation. More comprehensive numerical experiments are presented to investigate the long-time simulation, low dispersion and energy conservation properties of the conformal symplectic methods in both the attenuating homogeneous and heterogeneous media.

Fundamental understanding of wave generation and reception using d(36) type piezoelectric transducers.

PubMed

Zhou, Wensong; Li, Hui; Yuan, Fuh-Gwo

2015-03-01

A new piezoelectric wafer made from a PMN-PT single crystal with dominant piezoelectric coefficient d36 is proposed to generate and detect guided waves on isotropic plates. The in-plane shear coupled with electric field arising from the piezoelectric coefficient is not usually present for conventional piezoelectric wafers, such as lead zirconate titanate (PZT). The direct piezoelectric effect of coefficient d36 indicates that under external in-plane shear stress the charge is induced on a face perpendicular to the poled z-direction. On thin plates, this type of piezoelectric wafer will generate shear horizontal (SH) waves in two orthogonal wave propagation directions as well as two Lamb wave modes in other wave propagation directions. Finite element analyses are employed to explore the wave disturbance in terms of time-varying displacements excited by the d36 wafer in different directions of wave propagation to understand all the guided wave modes accurately. Experiments are conducted to examine the voltage responses received by this type of wafer, and also investigate results of tuning frequency and effects of d31 piezoelectric coefficient, which is intentionally ignored in the finite element analysis. All results demonstrate the main features and utility of proposed d36 piezoelectric wafer for guided wave generation and detection in structural health monitoring. Copyright © 2014 Elsevier B.V. All rights reserved.

Lamb wave-based damage quantification and probability of detection modeling for fatigue life assessment of riveted lap joint

NASA Astrophysics Data System (ADS)

He, Jingjing; Wang, Dengjiang; Zhang, Weifang

2015-03-01

This study presents an experimental and modeling study for damage detection and quantification in riveted lap joints. Embedded lead zirconate titanate piezoelectric (PZT) ceramic wafer-type sensors are employed to perform in-situ non-destructive testing during fatigue cyclical loading. A multi-feature integration method is developed to quantify the crack size using signal features of correlation coefficient, amplitude change, and phase change. In addition, probability of detection (POD) model is constructed to quantify the reliability of the developed sizing method. Using the developed crack size quantification method and the resulting POD curve, probabilistic fatigue life prediction can be performed to provide comprehensive information for decision-making. The effectiveness of the overall methodology is demonstrated and validated using several aircraft lap joint specimens from different manufactures and under different loading conditions.

[Study of the pathogenesis of paecilomycosis-complicated echinococcosis].

PubMed

Abdiev, F T; Mamysheva, N O; Streliaeva, A V; Gasparian, E R; Sagieva, A T; Sadykov, R V; Lazareva, N B; Kurilov, D V; Akhmedov, Iu M; Sadykov, V M; Shcheglova, T A; Zuev, S S; Mukhitdinov, Sh M; Vakhidova, A V

2012-01-01

Experiments were carried out on 35 lambs infected with echinococcus eggs taken from canine donors, 5 lambs with echinococcosis, 5 lambs with echinococcosis + paecilomycosis, 5 lambs with coenurosis, 5 with cysticercosis ovis, 5 with alveococcosis, 5 with paecilomycosis, inoculated by the material taken from patients; and 5 healthy lambs formed a control group. Cystic hydatidosis was found to induce substantial cardiovascular changes.

Effect of morning vs. afternoon grazing on intramuscular fatty acid composition in lamb.

PubMed

Vasta, Valentina; Pagano, Renato Italo; Luciano, Giuseppe; Scerra, Manuel; Caparra, Pasquale; Foti, Francesco; Cilione, Caterina; Biondi, Luisa; Priolo, Alessandro; Avondo, Marcella

2012-01-01

The aim of this study was to assess whether different grazing management affect animal performance and meat fatty acid composition. Thirty-five lambs were divided into three groups: 12 lambs grazed from 9 am to 5 pm (8 h group); 11 lambs grazed from 9 am to 1 pm (4hAM group) and 12 lambs grazed from 1 pm to 5 pm (4hPM group). The trial was conducted over 72 days. The 8 h lambs had greater DMI (P<0.0005) and final body weight (P<0.05) than the 4hPM and 4hAM lambs while carcass weight was not different between the three groups. The meat of the 4hPM lambs contained greater (P<0.05) percentages of polyunsaturated fatty acids, C18:2 cis-9 trans-11 and lower saturated fatty acids and C18:0 than the meat of the 8 h and 4hAM lambs. It is concluded that allowing lambs to graze during the afternoon rather than during 8 h does not compromise the carcass yield and results in a healthier meat fatty acid profile. Copyright © 2011 Elsevier Ltd. All rights reserved.

Hydrocortisone normalizes oxygenation and cGMP regulation in lambs with persistent pulmonary hypertension of the newborn

PubMed Central

Lakshminrusimha, Satyan; Wedgwood, Stephen; Czech, Lyubov; Gugino, Sylvia F.; Russell, James A.; Farrow, Kathryn N.; Steinhorn, Robin H.

2012-01-01

In the pulmonary vasculature, cGMP levels are regulated by soluble guanylate cyclase (sGC) and phosphodiesterase 5 (PDE5). We previously reported that lambs with persistent pulmonary hypertension of the newborn (PPHN) demonstrate increased reactive oxygen species (ROS) and altered sGC and PDE5 activity, with resultant decreased cGMP. The objective of this study was to evaluate the effects of hydrocortisone on pulmonary vascular function, ROS, and cGMP in the ovine ductal ligation model of PPHN. PPHN lambs were ventilated with 100% O2 for 24 h. Six lambs received 5 mg/kg hydrocortisone every 8 h times three doses (PPHN-hiHC), five lambs received 3 mg/kg hydrocortisone followed by 1 mg·kg−1·dose−1 times two doses (PPHN-loHC), and six lambs were ventilated with O2 alone (PPHN). All groups were compared with healthy 1-day spontaneously breathing lambs (1DSB). O2 ventilation of PPHN lambs decreased sGC activity, increased PDE5 activity, and increased ROS vs. 1DSB lambs. Both hydrocortisone doses significantly improved arterial-to-alveolar ratios relative to PPHN lambs, decreased PDE5 activity, and increased cGMP relative to PPHN lambs. High-dose hydrocortisone also increased sGC activity, decreased PDE5 expression, decreased ROS, and increased total vascular SOD activity vs. PPHN lambs. These data suggest that hydrocortisone treatment in clinically relevant doses improves oxygenation and decreases hyperoxia-induced changes in sGC and PDE5 activity, increasing cGMP levels. Hydrocortisone reduces ROS levels in part by increasing SOD activity in PPHN lambs ventilated with 100% O2. We speculate that hydrocortisone increases cGMP by direct effects on sGC and PDE5 expression and by attenuating abnormalities induced by oxidant stress. PMID:22198909

Lamb survival, glutathione redox state and immune function of neonates and lambs from periparturient Merino ewes supplemented with rumen-protected methionine.

PubMed

Liu, Shimin; Lei, Jason; Hancock, Serina; Scanlan, Victoria; Broomfield, Steve; Currie, Andrew; Thompson, Andrew

2016-10-01

Wool growth in Merino sheep demands a high level of sulphur amino acids, competing with body growth and the immune system, which may play a role in increasing the risk of lamb mortality. The hypothesis that dietary supplementation of methionine (Met) to Merino ewes during the late stages of pregnancy will improve foetal growth and alter immune competency of ewes and lambs was tested in a total of 120 grazing, pregnant Merino ewes. Sixty ewes were group-supplemented with 6.3 g/d rumen-protected Met (Met-Plus) per sheep from day 111 of pregnancy until day 7 after lambing, and the other 60 animals were used as a non-supplemented Control. Lambs from Met-supplemented ewes tended to be 10% heavier than Control lambs (p = 0.10), which did not affected the survival rate at weaning significantly. The supplemented ewes had slightly higher concentrations of total glutathione (GSH) in plasma at lambing (p < 0.06), but there were no differences between 1 and 3 months post-lambing in GSH, glutathione disulphide (GSSG) and the GSSG:GSH ratio. The GSSG:GSH ratio in the blood of ewes was elevated at lambing (p < 0.05), hinting that ewes were undergoing increased oxidative stress. The Met supplementation elevated the total IgG concentration (p < 0.05) in lambs aged 4 and 6 weeks, but did not change the IgG concentrations in colostrum and in plasma of 1-week-old lambs, and white blood cell counts and leukocyte types. The trend towards higher lamb birth weights in the Met-supplemented group requires further investigation as this may influence survival at birth and weaning.

Genetic parameters for lamb birth weight, survival and death risk traits.

PubMed

Everett-Hincks, J M; Mathias-Davis, H C; Greer, G J; Auvray, B A; Dodds, K G

2014-07-01

This paper reports genetic parameters for lamb survival and mortality traits on sheep farms in New Zealand. Lamb survival and mortality records were obtained from 38 flocks (103,357 lambs) from 5 yr of lambing data (2007 to 2011) and include many breeds and their crosses (predominantly Romney, Perendale, Coopworth, and Texel). A number of models were tested, all including environmental weather effects and investigating the random environmental effect of dam and litter (dam/year) as well as logit transformation for binary traits. Total heritability (direct + maternal) estimates were low for lamb viability at birth (0.01), lamb death risk to dystocia (0.01), and lamb death risk to starvation exposure (0.01) from birth to 3 d of age in an analysis accounting for direct and maternal genetic effects and the maternal environmental effects. Lamb survival heritabilities reported are very low (total heritabilities range from 0.02 to 0.06). The total heritabilities for the lamb death risk traits are lower than reported estimates of survival to 3 d of age or to weaning suggesting selection for the postmortem traits are not warranted at this time within these flocks. The total heritability for lamb birth weight was moderate (0.38) and the genetic correlations with the lamb death risk traits suggested that directional selection on lamb birth weight would have an effect on survival, although it is likely to have a nonlinear effect and therefore an optimum birth weight at which survival is maximized. This study has also shown that the total heritabilities may be overestimated when not accounting for maternal genetic and environment effects and in particular not accounting for the random environmental effect of litter (dam/year).

The influence of ovarian factors on the somatostatin-growth hormone system during the postnatal growth and sexual development in lambs.

PubMed

Wańkowska, Marta; Polkowska, Jolanta; Misztal, Tomasz; Romanowicz, Katarzyna

2012-07-01

The aim of the study was to elucidate the effects of ovarian hormones on somatostatin in the hypothalamic neurons and growth hormone (GH) secretion during the postnatal growth and development of sheep. The study was performed on 9-week-old (infantile) lambs that were ovary-intact (OVI) or ovariectomized (OVX) at 39 days of age, and on 16-week-old (juvenile) lambs that were OVI or OVX at 88 days of age. Hormones in neurons and somatotropic cells were assayed with immunohistochemistry and radioimmunoassay. Following ovariectomy, immunoreactive somatostatin was more abundant (p<0.05) in the hypothalamus of infantile lambs, whereas in juvenile lambs it was more abundant (p<0.05) in the periventricular nucleus but reduced (p<0.01) in the median eminence. In contrast to somatostatin in the hypothalamus, the content of immunoreactive GH in the hypophysis was less in OVX infantile lambs, but greater in OVX juvenile lambs (p<0.05). Basal blood serum concentrations of GH were greater (p<0.05) in OVX infantile lambs, whereas in OVX juvenile lambs, mean and basal concentrations of GH and amplitude of GH pulses were less than in OVI lambs (p<0.05). The postnatal increase in body weight was greatest in middle-late infancy (p<0.01). The body weight did not differ (p>0.05) between OVI and OVX lambs. In conclusion, ovarian factors may inhibit the GH secretion in infantile lambs but enhance the GH secretion in juvenile lambs. Transition to puberty, as related to the growth rate, appears to be due mainly to change in gonadal influence on the somatostatin neurosecretion. A stimulation of somatostatin output in the median eminence by gonadal factors in infancy is followed by a stimulation of somatostatin accumulation after infancy. Thus, ovarian factors modulate mechanisms within the somatotropic system of lambs to synchronize the somatic growth with sexual development. Copyright © 2012 Elsevier B.V. All rights reserved.

The effect of nutrition and body condition of triplet-bearing ewes during late pregnancy on the behaviour of ewes and lambs.

PubMed

Gronqvist, Gabriella V; Corner-Thomas, Rene A; Kenyon, Paul R; Stafford, Kevin J; Morris, Stephen T; Hickson, Rebecca Edith

2018-04-12

Triplet-born lambs are less likely to survive to weaning than twin-born or single-born lambs. Appropriate ewe-lamb bonding behaviours and lamb vigour behaviours are necessary for survival of lambs. The aim of this experiment was to determine whether maternal nutrition during late pregnancy influenced behaviour of the ewe and her lambs soon after birth, and to determine whether mid-pregnancy body condition score (BCS) influenced any behavioural response. The experiments included ewes that were in BCS 2.0, 2.5 or 3.0 in mid-pregnancy and were fed either ad libitum or to pregnancy-maintenance requirements in late-pregnancy (day 115 until 136 in experiment one, and day 128 until 141 in experiment two). The time taken for lambs to stand, contact dam, suck from dam and follow dam was recorded three to 18 hours after birth. The number of high- and low-pitched bleats emitted by the ewe and lambs was recorded, along with maternal behaviour score (MBS) of the ewe. Lambs in experiment two underwent a maternal-recognition test at 12 or 24 h. There were significant effects of feeding treatment on bleating behaviour of ewes and lambs, but these were inconsistent among BCS groups and between experiments. Lamb vigour behaviours were not affected by feeding treatment. In experiment one, there was no effect of feeding treatment or BCS on MBS, but in experiment two, ewes in BCS3 in mid-pregnancy had greater MBS than ewes in BCS2 in mid-pregnancy (MBS 3.1/5 vs MBS 2.1/5; P<0.05). Given there were no repeatable effects on behaviour of ewes and lambs, ad libitum feeding rather than feeding for pregnancy-maintenance requirements can not be used to improve behaviours soon after birth of triplet-bearing ewes in BCS 2 - 3 and their lambs in extensive pastoral conditions.

Performance of Djallonké sheep under an extensive system of production in Faranah, Guinea.

PubMed

Mourad, M; Gbanamou, G; Balde, I B

2001-10-01

A total of 147 ewes, 4 rams and 188 lambs of their progeny of the Djallonké breed of sheep were used to study the factors affecting reproductive and growth traits and the causes of lamb mortality. Data on ewes were collected during a 12-month period, while those on the lambs born to 123 of the ewes were collected until they were 12 months of age. The average fertility and abortion rates were 0.84 and 0.09. The fertility rate increased and the abortion rate decreased with increasing age of the ewes (p<0.05). The number of lambs born per ewe joined, litter weight at birth per ewe joined and litter weight at weaning per ewe joined were 1.28, 3.5 kg and 17 kg, respectively. The average numbers of lambs born per ewe, lambs born alive per ewe, lambs born dead per ewe and lambs per ewe that died between birth and weaning were 1.53, 1.43, 0.03 and 0.3, respectively. The age of the ewes significantly (p<0.05) affected all these traits except the number of dead lambs and the index of fertility (94%). The age of the ewes significantly (p<0.05) affected the birth weight and the weight at 6 and 12 months of age, whereas the lambing season significantly (p<0.05) affected all the growth traits studied. The type of birth was the most important source of variation in body weights of lambs. Sex had no significant (p>0.05) effect on the growth traits studied. The complex 'starvation-bad management-light body weight at birth' caused 48% of the lamb mortality between birth and weaning, while diarrhoea, pneumonia and internal and external parasites caused approximately 52% of the lamb mortality over the same period. The seasonal raw mortality rate of the lambs before weaning was highest in the humid season.

Mineral composition of lamb carcasses from the United States and New Zealand.

PubMed

Lin, K C; Cross, H R; Johnson, H K; Breidenstein, B C; Randecker, V; Field, R A

1988-01-01

The mineral composition-iron (Fe), zinc (Zn), copper (Cu), calcium (Ca), magnesium (Mg), sodium (Na), potassium (K), fluoride (F), and phosphorus (P) (New Zealand lamb only)-of lean tissue from lamb retail cuts was studied. Twenty-four US lamb carcasses of different ages (5 to 11 months), geographical regions (Texas, Colorado and Montana) and USDA quality grades (Prime and Choice) and 27 New Zealand lamb carcasses from three weight groups (11 to 12·5 kg, 13 to 14·5 kg, and 16·5 to 18 kg), age rangining from 7 to 8 months, were selected for use in this study. Mineral concentrations were influenced more by retail cut and age than by quality grade or weigth group. Foreshank and shoulder cuts from both the US and New Zealand group consistently had the highest (P < 0·05) Zn content among the cuts. The K content of the muscle in US lambs increased as age increased, while the level of Ca and Zn in New Zealand lambs decreased as carcass weight increased. Except for Ca, the mineral concentrations of the lean tissue from US lambs were higher than the New Zealand lambs, although the differences were not always significant. US lambs had approximately 20%, 30% and 37% more Fe, Zn and Mg, respectively, but 27% less Ca than lean tissue from the New Zealand lambs. Copyright © 1989. Published by Elsevier Ltd.

Genetic evaluation of weaning weight and probability of lambing at 1 year of age in Targhee lambs

USDA-ARS?s Scientific Manuscript database

The objective of this study was to investigate genetic control of 120-day weaning weight and the probability of lambing at 1 year of age in Targhee ewe lambs. Records of 5,967 ewe lambs born from 1989 to 2012 and first exposed to rams for breeding at approximately 7 months of age were analyzed. Reco...

Genetic and physiological determinants of maternal behavior and lamb survival: implications for low-input sheep management.

PubMed

Dwyer, C M

2008-04-01

The relatively intensive supervision afforded many ewes at lambing time is a barrier to the development of low-input sheep management systems. However, in some flocks, reduction in this level of supervision may initially affect lamb mortality and animal welfare. In this review, possibilities for optimizing behavioral interaction between the ewe and lamb are considered, with the goal of improving lamb survival without the need for high levels of human supervision. At birth, ewes show specific behavioral patterns (e.g., licking or grooming, low-pitched bleats, udder acceptance) that facilitate the transition of the lamb from pre- to postnatal life and that accompany the formation of an exclusive olfactory memory for the lamb. The lamb also performs a specific sequence of behaviors directed toward standing, finding the udder, and sucking. The successful accomplishment of these behavior patterns is vital for the formation of a strong attachment between both partners, and for lamb survival. The expression of maternal behavior in the ewe is affected by her previous maternal experience, by nutrition in pregnancy, by breed, by temperament, and, to some extent, by the behavior of her lamb. The maternal care expressed by a ewe at parturition is indicative of her behavior throughout that lactation and in successive pregnancies, suggesting an underlying basis to maternal care intrinsic to that ewe. Studies with Scottish Blackface and Suffolk ewes show that ewes expressing high levels of maternal care have elevated plasma estradiol in late gestation compared with ewes with poorer maternal care, and that circulating estradiol concentration is correlated with maternal behaviors. Although the genetic basis of maternal behaviors has still to be fully determined, there are possibilities of improving maternal behavior by selection, and a better understanding of the neuroendocrine processes underlying individual differences in maternal behavior may help in developing selection strategies. In addition, selection on lamb behaviors, which show some genetic basis, may also be a route to improve lamb survival. Because behavior of both the ewe and lamb is affected by environmental factors, appropriate management, through pregnancy and at parturition, will enhance the expression of maternal behavior and lamb vigor, and so contribute to improving lamb survival.

The passive transfer of immunity to Taenia ovis in lambs via colostrum.

PubMed

Sutton, R J

1979-09-01

Colostrum from ewes that had been repeatedly exposed to cestode infection, whether or not their immunity was boosted by vaccination with Taenia ovis, transferred a strong immunity to the lambs. Susceptible ewes, not recently exposed to tapeworm eggs, gave no protection to their lambs via the colostrum. There was no evidence that colostrum-deprived lambs were more susceptible to infection with T ovis than lambs that received colostrum from non-immune ewes. Colostrum from naturally immune vaccinated ewes gave good protection to lambs for up to six weeks but thereafter the effect was variable. The immunity that developed in susceptible ewes after vaccination with activated embryos was not passed on to the lambs via the colostrum.

7 CFR 1280.210 - Powers and duties of the Board.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Lamb Promotion... (including producer information), designed to strengthen the lamb industry's position in the marketplace...

7 CFR 1280.201 - Establishment and membership.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Lamb Promotion... Lamb Promotion, Research and Information Board of 13 members. Members of the Board shall be appointed...

Organic selenium supplementation increased selenium concentrations in ewe and newborn lamb blood and in slaughter lamb meat compared to inorganic selenium supplementation.

PubMed

Steen, Arvid; Strøm, Turid; Bernhoft, Aksel

2008-03-31

Selenium is part of the antioxidant defence system in animals and humans. The available selenium concentration in soil is low in many regions of the world. The purpose of this study was to evaluate the effect of organic versus inorganic selenium supplementation on selenium status of ewes, their lambs, and slaughter lambs. Ewes on four organic farms were allocated five or six to 18 pens. The ewes were given either 20 mg/kg inorganic selenium as sodium selenite or organic selenium as selenized nonviable yeast supplementation for the two last months of pregnancy. Stipulated selenium concentrations in the rations were below 0.40 mg/kg dry matter. In addition 20 male lambs were given supplements from November until they were slaughtered in March. Silage, hay, concentrates, and individual ewe blood samples were taken before and after the mineral supplementation period, and blood samples were taken from the newborn lambs. Blood samples from ewes and lambs in the same pens were pooled. Muscle samples were taken from slaughter lambs in March. Selenium concentrations were determined by atomic absorption spectrometry with a hydride generator system. In the ANOVA model, selenium concentration was the continuous response variable, and selenium source and farm were the nominal effect variables. Two-sample t-test was used to compare selenium concentrations in muscle samples from the slaughtered lambs that received either organic or inorganic selenium supplements. In all ewe pens the whole blood selenium concentrations increased during the experimental period. In addition, ewe pens that received organic selenium had significantly higher whole blood selenium concentrations (mean 0.28 microg/g) than ewe pens that received inorganic selenium (mean 0.24 microg/g). Most prominent, however, was the difference in their lambs; whole blood mean selenium concentration in lambs from mothers that received organic selenium (mean 0.27 microg/g) was 30% higher than in lambs from mothers that received inorganic selenium (mean 0.21 microg/g). Slaughter lambs that received organic selenium had 50% higher meat selenium concentrations (mean 0.12 mg/kg wet weight) than lambs that received inorganic selenium (mean 0.08 mg/kg wet weight). Organic selenium supplementation gave higher selenium concentration in ewe and newborn lamb blood and slaughter lamb meat than inorganic selenium supplementation.

Organic selenium supplementation increased selenium concentrations in ewe and newborn lamb blood and in slaughter lamb meat compared to inorganic selenium supplementation

PubMed Central

Steen, Arvid; Strøm, Turid; Bernhoft, Aksel

2008-01-01

Background Selenium is part of the antioxidant defence system in animals and humans. The available selenium concentration in soil is low in many regions of the world. The purpose of this study was to evaluate the effect of organic versus inorganic selenium supplementation on selenium status of ewes, their lambs, and slaughter lambs. Methods Ewes on four organic farms were allocated five or six to 18 pens. The ewes were given either 20 mg/kg inorganic selenium as sodium selenite or organic selenium as selenized nonviable yeast supplementation for the two last months of pregnancy. Stipulated selenium concentrations in the rations were below 0.40 mg/kg dry matter. In addition 20 male lambs were given supplements from November until they were slaughtered in March. Silage, hay, concentrates, and individual ewe blood samples were taken before and after the mineral supplementation period, and blood samples were taken from the newborn lambs. Blood samples from ewes and lambs in the same pens were pooled. Muscle samples were taken from slaughter lambs in March. Selenium concentrations were determined by atomic absorption spectrometry with a hydride generator system. In the ANOVA model, selenium concentration was the continuous response variable, and selenium source and farm were the nominal effect variables. Two-sample t-test was used to compare selenium concentrations in muscle samples from the slaughtered lambs that received either organic or inorganic selenium supplements. Results In all ewe pens the whole blood selenium concentrations increased during the experimental period. In addition, ewe pens that received organic selenium had significantly higher whole blood selenium concentrations (mean 0.28 μg/g) than ewe pens that received inorganic selenium (mean 0.24 μg/g). Most prominent, however, was the difference in their lambs; whole blood mean selenium concentration in lambs from mothers that received organic selenium (mean 0.27 μg/g) was 30% higher than in lambs from mothers that received inorganic selenium (mean 0.21 μg/g). Slaughter lambs that received organic selenium had 50% higher meat selenium concentrations (mean 0.12 mg/kg wet weight) than lambs that received inorganic selenium (mean 0.08 mg/kg wet weight). Conclusion Organic selenium supplementation gave higher selenium concentration in ewe and newborn lamb blood and slaughter lamb meat than inorganic selenium supplementation. PMID:18377659

Effect of different corn processing methods on enzyme producing bacteria, protozoa, fermentation and histomorphometry of rumen in fattening lambs

PubMed Central

Gholami, Mohammad Amin; Forouzmand, Masihollah; Khajavi, Mokhtar; Hossienifar, Shima; Naghiha, Reza

2018-01-01

The purpose of this study was to investigate the effect of different corn processing methods on rumen microbial flora, histomorphometry and fermentation in fattening male lambs. Twenty male lambs (average age and weight of 90 days and 25.00 ± 1.10 kg, respectively) were used in a completely randomized design including four treatments and five replicates each over 80 days long period: 1) Lambs fed ground corn seeds; 2) Lambs fed steam-rolled corn; 3) Lambs fed soaked corn seeds (24 hr) and 4) Lambs fed soaked corn seeds (48 hr). At the end of the experiment, three lambs of each treatment were slaughtered and samples were collected for pH, volatile fatty acids, amylolytic, proteolytic, cellulytic and heterophilic bacteria and protozoa assessment. The number of proteolytic bacteria in soaked corn seeds was significantly increased in comparison with other treatments. The thickness of wall, papillae and muscular layers of rumen in the soaked corn seeds treatment was significantly increased. Overall, from a practical point of view, soaked corn processing could be generally used in lambs fattening system. PMID:29719663

7 CFR 1280.117 - Producer information.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.117 Producer information..., or other information that would facilitate an increase in the demand for lambs or lamb products. ...

Genetic parameters for ewe reproductive performance and peri-parturient fecal egg counts and their genetic relationships with lamb body weights and fecal egg counts in Katahdin sheep

USDA-ARS?s Scientific Manuscript database

This study estimated genetic parameters for ewe reproductive traits [number of lambs born (NLB) and weaned (NLW) per ewe lambing] and peri-parturient (PPR) fecal egg counts (FEC) at lambing (PPR0) and 30 d postpartum (PPR30), and their genetic relationships with lamb BW and FEC in Katahdin sheep. Th...

Production benefits from pre- and post-lambing anthelmintic treatment of ewes on commercial farms in the southern North Island of New Zealand.

PubMed

Miller, C M; Ganesh, S; Garland, C B; Leathwick, D M

2015-07-01

To measure the magnitude and variability in production responses to anthelmintic treatments administered to adult ewes around lambing. Ewes carrying twin lambs, from sheep and beef farms (eight in Year 1 and six in Year 2) in the Wairarapa region of New Zealand, were enrolled in 14 trials (part of an experiment carried out on one farm in one year). Experiment 1 compared ewes treated 2-4 weeks pre-lambing with a controlled release capsule (CRC) containing abamectin, albendazole, Se and Co, to ewes injected pre-lambing with a long-acting Se plus vitamin B12 product, and to untreated ewes. Experiment 2 included these treatments, plus a CRC administered at pregnancy scanning. Experiment 3 included the same treatments as Experiment 1, plus administration of a CRC containing albendazole, Se and Co, injectable moxidectin or oral derquantel plus abamectin, all administered pre-lambing, or oral derquantel plus abamectin administered 4-6 weeks after lambing. Variables compared were ewe liveweight at weaning and pre-mating, lamb liveweight at weaning, total weight of lamb weaned per ewe and ewe dag score at weaning. Ewes treated with a CRC pre-lambing were heavier than untreated ewes (mean 3.2 kg) at weaning in 12/14 trials, and pre-mating (mean 2.8 kg) in 9/14 trials (p<0.001). Compared with mineral-treated ewes the mean difference was 2.8 kg pre-lambing (9/14 trials) and 1.7 kg pre-weaning (6/14 trials). Lambs reared by treated ewes were heavier (mean 1.55 kg) at weaning in 6/14 trials (p<0.001), but there was no effect of CRC treatment on total weight of lambs weaned per ewe (p=0.507). Variation in weight of lamb weaned per ewe was largely explained by differences in lamb survival from birth to weaning (p<0.001), with no effect of CRC treatment (p>0.65). Treatment of ewes with a CRC at pregnancy scanning was neither better nor worse than a pre-lambing treatment (p=0.065). There was no difference in the response from treatment with either of the two CRC or moxidectin. Treatment with short-acting oral anthelmintics resulted in no consistent benefit. Anthelmintic treatments administered to ewes around lambing resulted in variable responses between farms and years, which in some trials were negative for some variables, and some of the variability was due to the mineral component of the CRC. The widespread perception amongst farmers and veterinarians that anthelmintic treatment of ewes around lambing will always result in positive benefits is not supported.

Ovine offspring growth and diet digestibility are influenced by maternal selenium supplementation and nutritional intake during pregnancy despite a common postnatal diet.

PubMed

Neville, T L; Caton, J S; Hammer, C J; Reed, J J; Luther, J S; Taylor, J B; Redmer, D A; Reynolds, L P; Vonnahme, K A

2010-11-01

Lambs born from feed-restricted or overfed ewes can be lighter at birth, whereas maternal Se supplementation can increase fetal size near term. We hypothesized that birth weight would be inversely related to feed efficiency and growth rates during postnatal development. To examine the effects of maternal dietary Se and nutrient restriction or excess on postnatal lamb growth, diet digestibility, and N retention, 82 ewe lambs (52.2 ± 0.8 kg) were allotted randomly to 1 of 6 treatments in a 2 × 3 factorial arrangement. Factors were dietary Se [adequate Se (9.5 μg/kg of BW; ASe) vs. high Se (Se-enriched yeast; 81.8 μg/kg of BW; HSe)] and maternal nutritional intake [60% (restricted, RES), 100% (control, CON), or 140% (high, HI) of NRC requirements]. Selenium treatments began at breeding. Nutritional treatments began on d 50 of gestation. Lambs were immediately removed from their dams at parturition, provided artificial colostrum, and fed milk replacer until weaning. After weaning, lambs were maintained using common management and on common diets until necropsy at 180 d. Male and female lambs from RES-fed ewes were lighter (P ≤ 0.03) at birth than lambs from CON-fed ewes, with lambs from HI-fed ewes being intermediate. Although maternal nutritional intake influenced (P < 0.06) BW gain before weaning on d 57, both maternal nutritional intake and sex of offspring influenced (P ≤ 0.09) BW gain from d 57 to 180. Although maternal nutritional intake did not influence (P ≥ 0.35) female lamb BW gain, male lambs from RES-fed ewes were lighter (P ≤ 0.09) than those from CON-fed ewes until d 162. By d 180, male lambs from RES- and HI-fed ewes were lighter (P ≤ 0.09) than those from CON-fed ewes. In a subset of lambs used in a feed efficiency study, namely, those born to ASe ewes, HI maternal nutritional intake decreased (P ≤ 0.09) ADG and G:F compared with lambs born to RES- and CON-fed ewes, which did not differ (P ≥ 0.60). Conversely, when lambs were born to HSe ewes, HI maternal nutritional intake increased (P ≤ 0.01) ADG and G:F compared with CON, with RES being intermediate. Moreover, lambs born to ASe-HI ewes had decreased (P < 0.01) ADG and G:F compared with lambs born to HSe-HI ewes. Furthermore, male lambs had a greater (P < 0.01) G:F than female lambs. Maternal diet did not affect (P ≥ 0.11) N retention in male lambs. These data indicate that maternal nutrition during gestation and sex of the offspring alter postnatal growth and efficiency of growth in offspring despite similar postnatal management.

Bacterial and Protozoal Communities and Fatty Acid Profile in the Rumen of Sheep Fed a Diet Containing Added Tannins ▿

PubMed Central

Vasta, Valentina; Yáñez-Ruiz, David R.; Mele, Marcello; Serra, Andrea; Luciano, Giuseppe; Lanza, Massimiliano; Biondi, Luisa; Priolo, Alessandro

2010-01-01

This study evaluated the effects of tannins on ruminal biohydrogenation (BH) due to shifts in the ruminal microbial environment in sheep. Thirteen lambs (45 days of age) were assigned to two dietary treatments: seven lambs were fed a barley-based concentrate (control group) while the other six lambs received the same concentrate with supplemental quebracho tannins (9.57% of dry matter). At 122 days of age, the lambs were slaughtered, and the ruminal contents were subjected to fatty acid analysis and sampled to quantify populations of Butyrivibrio fibrisolvens, which converts C18:2 c9-c12 (linoleic acid [LA]) to C18:2 c9-t11 (rumenic acid [RA]) and then RA to C18:1 t11 (vaccenic acid [VA]); we also sampled for Butyrivibrio proteoclasticus, which converts VA to C18:0 (stearic acid [SA]). Tannins increased (P < 0.005) VA in the rumen compared to the tannin-free diet. The concentration of SA was not affected by tannins. The SA/VA ratio was lower (P < 0.005) for the tannin-fed lambs than for the controls, suggesting that the last step of the BH process was inhibited by tannins. The B. proteoclasticus population was lower (−30.6%; P < 0.1), and B. fibrisolvens and protozoan populations were higher (+107% and +56.1%, respectively; P < 0.05) in the rumen of lambs fed the tannin-supplemented diet than in controls. These results suggest that quebracho tannins altered BH by changing ruminal microbial populations. PMID:20173064

Bacterial and protozoal communities and fatty acid profile in the rumen of sheep fed a diet containing added tannins.

PubMed

Vasta, Valentina; Yáñez-Ruiz, David R; Mele, Marcello; Serra, Andrea; Luciano, Giuseppe; Lanza, Massimiliano; Biondi, Luisa; Priolo, Alessandro

2010-04-01

This study evaluated the effects of tannins on ruminal biohydrogenation (BH) due to shifts in the ruminal microbial environment in sheep. Thirteen lambs (45 days of age) were assigned to two dietary treatments: seven lambs were fed a barley-based concentrate (control group) while the other six lambs received the same concentrate with supplemental quebracho tannins (9.57% of dry matter). At 122 days of age, the lambs were slaughtered, and the ruminal contents were subjected to fatty acid analysis and sampled to quantify populations of Butyrivibrio fibrisolvens, which converts C(18:2) c9-c12 (linoleic acid [LA]) to C(18:2) c9-t11 (rumenic acid [RA]) and then RA to C(18:1) t11 (vaccenic acid [VA]); we also sampled for Butyrivibrio proteoclasticus, which converts VA to C(18:0) (stearic acid [SA]). Tannins increased (P < 0.005) VA in the rumen compared to the tannin-free diet. The concentration of SA was not affected by tannins. The SA/VA ratio was lower (P < 0.005) for the tannin-fed lambs than for the controls, suggesting that the last step of the BH process was inhibited by tannins. The B. proteoclasticus population was lower (-30.6%; P < 0.1), and B. fibrisolvens and protozoan populations were higher (+107% and +56.1%, respectively; P < 0.05) in the rumen of lambs fed the tannin-supplemented diet than in controls. These results suggest that quebracho tannins altered BH by changing ruminal microbial populations.

Damage imaging using Lamb waves for SHM applications

NASA Astrophysics Data System (ADS)

Stepinski, Tadeusz; Ambroziński, Łukasz; Uhl, Tadeusz

2015-03-01

2-D ultrasonic arrays, due to their beam-steering capability and all azimuth angle coverage are a very promising tool for the inspection of plate-like structures using Lamb waves (LW). Contrary to the classical linear phased arrays (PAs) the 2D arrays enable unequivocal defect localization and they are even capable of mode selectivity of the received LWs . Recently, it has been shown that multistatic synthetic focusing (SF) algorithms applied for 2D arrays are much more effective than the classical phase array mode commonly used in NDT. The multistatic SF assumes multiple transmissions of elements in a transmitting aperture and off-line processing of the data acquired by a receiving aperture. In the simplest implementation of the technique, only a single multiplexed input and a number of output channels are required, which results in significant hardware simplification compared with the PA systems. On the one hand implementation of the multistatic SF to 2D arrays creates additional degrees of freedom during the design of the array topology, which complicates the array design process. On the other hand, it enables designing sparse arrays with performance similar to that of the fully populated dense arrays. In this paper we present a general systematic approach to the design and optimization of imaging systems based on the 2D array operating in the multistatic mode. We start from presenting principles of the SF schemes applied to LW imaging. Then, we outline the coarray concept and demonstrate how it can be used for reducing number of elements of the 2D arrays. Finally, efficient tools for the investigation and experimental verification of the designed 2D array prototypes are presented. The first step in the investigation is theoretical evaluation performed using frequency-dependent structure transfer function (STF), which enables approximate simulation of an array excited with a tone-burst in a dispersive medium. Finally, we show how scanning laser vibrometer, sensing waves in multiple points corresponding to the locations of the 2D receiving array elements, can be used as a tool for rapid experimental verification of the developed topologies. The presented methods are discussed in terms of the beampatterns and sparse versions of the fully populated array topologies are be presented. The effect of apodization applied to the array elements is also investigated. Both simulated and experimental results are included.

Growth performance, nutrients digestibility, and blood metabolites of lambs fed diets supplemented with probiotics during pre- and post-weaning period

PubMed Central

Saleem, A. M.; Zanouny, A. I.; Singer, A. M.

2017-01-01

Objective Two experiments were conducted to evaluate the effects on growth performance, digestibility, and blood metabolites of lambs during pre- and post-weaning period of inclusion of a commercial probiotic (PRO) containing a mixture of two strains of Pediococcus, Pediococcus acidilactici (1×106 colony-forming unit [cfu]/g) and Pediococcus pentosaceus (1.3×106 cfu/g), with dextrose as the carrier compound compared to a diet based on concentrate mixture and wheat straw. Methods In exp. 1, 24 male lambs of about 15±2.6 d age and initial body weight (BW) of 5.52±0.6 kg were randomly allocated into three groups. One group received control diet without additives, and remainders received control diet supplemented with 0.5 or 1 g PRO/lamb/d. Daily feed intake and biweekly BW were recorded. In exp. 2, five lambs, (initial BW = 29.72±1.15 kg, age = 6.54±0.32 mo) were used as experimental animals in a digestion trial. They were fed the same diets as in Exp. 1. Results The supplementation of PRO did not result in any significant differences in milk intake, average daily gain (ADG), or total gain between treatments during the pre-weaning period. Total dry matter intake tended to be greater (p = 0.07) with addition of PRO in the post-weaning diets. During post-weaning phase, the final BW, ADG, total gain, and feed conversion ratio of the lambs receiving PRO treatments tended to be greater (p≤0.10) than the control group. Addition of PRO in post-weaning diet decreased (p≤0.01) blood urea and cholesterol concentrations. With the exception of ether extract digestibility, all nutrients digestibility were improved with inclusion PRO in the post-weaning diets. Conclusion Lambs that received PRO in post-weaning diet appeared to show a better performance than lambs in pre-weaning period. Addition of the probiotic in the post-weaning diet trended towards improved dry matter intake, growth performance, feed conversion ratio, and nutrients digestibility. PMID:28002935

Development and validation of equations utilizing lamb vision system output to predict lamb carcass fabrication yields.

PubMed

Cunha, B C N; Belk, K E; Scanga, J A; LeValley, S B; Tatum, J D; Smith, G C

2004-07-01

This study was performed to validate previous equations and to develop and evaluate new regression equations for predicting lamb carcass fabrication yields using outputs from a lamb vision system-hot carcass component (LVS-HCC) and the lamb vision system-chilled carcass LM imaging component (LVS-CCC). Lamb carcasses (n = 149) were selected after slaughter, imaged hot using the LVS-HCC, and chilled for 24 to 48 h at -3 to 1 degrees C. Chilled carcasses yield grades (YG) were assigned on-line by USDA graders and by expert USDA grading supervisors with unlimited time and access to the carcasses. Before fabrication, carcasses were ribbed between the 12th and 13th ribs and imaged using the LVS-CCC. Carcasses were fabricated into bone-in subprimal/primal cuts. Yields calculated included 1) saleable meat yield (SMY); 2) subprimal yield (SPY); and 3) fat yield (FY). On-line (whole-number) USDA YG accounted for 59, 58, and 64%; expert (whole-number) USDA YG explained 59, 59, and 65%; and expert (nearest-tenth) USDA YG accounted for 60, 60, and 67% of the observed variation in SMY, SPY, and FY, respectively. The best prediction equation developed in this trial using LVS-HCC output and hot carcass weight as independent variables explained 68, 62, and 74% of the variation in SMY, SPY, and FY, respectively. Addition of output from LVS-CCC improved predictive accuracy of the equations; the combined output equations explained 72 and 66% of the variability in SMY and SPY, respectively. Accuracy and repeatability of measurement of LM area made with the LVS-CCC also was assessed, and results suggested that use of LVS-CCC provided reasonably accurate (R2 = 0.59) and highly repeatable (repeatability = 0.98) measurements of LM area. Compared with USDA YG, use of the dual-component lamb vision system to predict cut yields of lamb carcasses improved accuracy and precision, suggesting that this system could have an application as an objective means for pricing carcasses in a value-based marketing system.

An evaluation of the lamb vision system as a predictor of lamb carcass red meat yield percentage.

PubMed

Brady, A S; Belk, K E; LeValley, S B; Dalsted, N L; Scanga, J A; Tatum, J D; Smith, G C

2003-06-01

An objective method for predicting red meat yield in lamb carcasses is needed to accurately assess true carcass value. This study was performed to evaluate the ability of the lamb vision system (LVS; Research Management Systems USA, Fort Collins, CO) to predict fabrication yields of lamb carcasses. Lamb carcasses (n = 246) were evaluated using LVS and hot carcass weight (HCW), as well as by USDA expert and on-line graders, before fabrication of carcass sides to either bone-in or boneless cuts. On-line whole number, expert whole-number, and expert nearest-tenth USDA yield grades and LVS + HCW estimates accounted for 53, 52, 58, and 60%, respectively, of the observed variability in boneless, saleable meat yields, and accounted for 56, 57, 62, and 62%, respectively, of the variation in bone-in, saleable meat yields. The LVS + HCW system predicted 77, 65, 70, and 87% of the variation in weights of boneless shoulders, racks, loins, and legs, respectively, and 85, 72, 75, and 86% of the variation in weights of bone-in shoulders, racks, loins, and legs, respectively. Addition of longissimus muscle area (REA), adjusted fat thickness (AFT), or both REA and AFT to LVS + HCW models resulted in improved prediction of boneless saleable meat yields by 5, 3, and 5 percentage points, respectively. Bone-in, saleable meat yield estimations were improved in predictive accuracy by 7.7, 6.6, and 10.1 percentage points, and in precision, when REA alone, AFT alone, or both REA and AFT, respectively, were added to the LVS + HCW output models. Use of LVS + HCW to predict boneless red meat yields of lamb carcasses was more accurate than use of current on-line whole-number, expert whole-number, or expert nearest-tenth USDA yield grades. Thus, LVS + HCW output, when used alone or in combination with AFT and/or REA, improved on-line estimation of boneless cut yields from lamb carcasses. The ability of LVS + HCW to predict yields of wholesale cuts suggests that LVS could be used as an objective means for pricing carcasses in a value-based marketing system.

Assessing Timing and Causes of Neonatal Lamb Losses in a Bighorn Sheep ( Ovis canadensis canadensis ) Herd via Use of Vaginal Implant Transmitters.

PubMed

Grigg, Jamin L; Wolfe, Lisa L; Fox, Karen A; Killion, Halcyon J; Jennings-Gaines, Jessica; Miller, Michael W; P Dreher, Brian

2017-07-01

We evaluated the use of vaginal implant transmitters (VITs) as a means of detecting, capturing, and radio collaring Rocky Mountain bighorn sheep ( Ovis canadensis canadensis) lambs to estimate survival and to facilitate carcass recovery to assess causes of mortality. We focused on one of several bighorn herds in Colorado, US, suffering from depressed recruitment that was not preceded by a classic all-age die-off. We captured, radio-collared, diagnosed pregnancy by ultrasound examination, and inserted VITs into 15 pregnant ewes from a herd residing near Granite, Colorado. We were subsequently able to collar a lamb from each of 13 VITs, and two additional lambs opportunistically from ewes without transmitters. As lambs died, we recovered and submitted carcasses for necropsy and laboratory assessment. All lambs captured and one additional lamb (carcass found opportunistically) were dead by about 130 d of age: 11 died of apparent pneumonia (all within 8-10 wk of age), one died from trauma after being kicked or trampled, one was killed by a mountain lion ( Puma concolor ), and three died of starvation likely caused by abandonment after capture. Pneumonic lambs had involvement of Mycoplasma ovipneumoniae and leukotoxigenic Bibersteinia trehalosi . The use of VITs and lamb collars enabled us to efficiently identify pneumonia as the predominant cause of depressed lamb recruitment in this herd; however, we urge care in neonatal lamb handling to minimize abandonment.

Guided ultrasonic waves for determining effective orthotropic material parameters of continuous-fiber reinforced thermoplastic plates.

PubMed

Webersen, Manuel; Johannesmann, Sarah; Düchting, Julia; Claes, Leander; Henning, Bernd

2018-03-01

Ultrasonic methods are widely established in the NDE/NDT community, where they are mostly used for the detection of flaws and structural damage in various components. A different goal, despite the similar technological approach, is non-destructive material characterization, i.e. the determination of parameters like Young's modulus. Only few works on this topic have considered materials with high damping and strong anisotropy, such as continuous-fiber reinforced plastics, but due to the increasing demand in the industry, appropriate methods are needed. In this contribution, we demonstrate the application of laser-induced ultrasonic Lamb waves for the characterization of fiber-reinforced plastic plates, providing effective parameters for a homogeneous, orthotropic material model. Copyright © 2017 Elsevier B.V. All rights reserved.

7 CFR 1280.211 - Prohibited activities.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Lamb Promotion, Research, and Information... and agents of the lamb industry from engaging in: (a) Any action that would be a conflict of interest...

7 CFR 1280.216 - Procedure for obtaining a refund.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Expenses § 1280... collected applicant's assessment; (3) Number of head of lambs, weight of lambs, or its equivalent, on which...

7 CFR 1280.107 - Feeder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.107 Feeder. Feeder means any person who acquires ownership of lambs and feeds such lambs in the U.S. until they reach slaughter...

7 CFR 1280.221 - Prohibition on use of funds.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SERVICE (MARKETING AGREEMENTS AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Assessments... pursuant to this title shall not make false or misleading claims on behalf of lamb or lamb products or...

Effectiveness of a short-term treatment with progesterone injections on synchrony of lambing and fertility in tropical hair sheep.

PubMed

Knights, Marlon; Ramgattie, Reeza; Siew, Narendra; Singh-Knights, Doolarie; Bourne, Gregory

2011-06-01

The efficacy of using a low cost system for delivering progesterone as part of an estrous synchronization protocol in sheep was evaluated. In experiment 1, Barbados Black Belly ewes (n=34) and ewe lambs (n=35; 37.5±0.9 kg) were assigned to be untreated, control animals (C), or to receive PGF(2α) on d0 (PG), or receive two injections of progesterone (200mg, i.m. each) on D -5 and on D -2.5, prior to PGF(2α), on D 0 (2PPG). Treatment with 2PPG increased the proportion of animals lambing to the first service (P<0.05), an effect that was greater in ewe lambs than ewes (treatment × parity; P<0.05). The interval from ram introduction to lambing and the mean lambing day was less (P=0.04) in the 2PPG-treated animals compared to control animals. In Experiment 2, lactating ewes from experiment 1 (n=61) 60-85 days postpartum were assigned within parity and number of lambs reared to remain nursing (S; n=29) or weaned (W; n=32) 3 weeks prior to treatment with the 2PPG protocol. There was no effect of treatment on the proportion of animals lambing to the first service or overall, interval from ram introduction to lambing and lambing interval. An 8-month lambing interval was observed in ewes in which estrus was synchronized regardless of physiological state. In conclusion, the two-progesterone injection synchronization protocol may be used as a practical low cost and efficient method of synchronizing estrus to reduce the lambing interval and maximize productivity in tropical breeds of sheep. Copyright © 2011 Elsevier B.V. All rights reserved.

Temperament and its heritability in Corriedale and Merino lambs.

PubMed

Zambra, N; Gimeno, D; Blache, D; van Lier, E

2015-03-01

Temperament can be defined as the fearfulness and reactivity of an animal in response to humans and strange, novel or threatening environments. The productive performance of an animal is affected by its temperament, and selection of calm animals might improve their adaptation to the farming environment and handling, as well as improve productivity. The temperament was measured in lambs of two breeds of sheep in Uruguay. The effects of dam's age, type of birth, age of the lamb and contemporary group (CG; lambs belonging to the same year, flock, sex and rearing group) on the temperament of the lambs and the heritability of temperament were estimated with a Bayesian analysis using Gibbs sampling. Overall, 4962 Corriedale lambs and 2952 Merino lambs from 13 farms were tested. Temperament was measured using the isolation box test, isolating a lamb inside the box for 30 s, and recording the vibrations produced by its movements. The average temperament score (±s.e.m.) of the Corriedale lambs was 24.7 (±0.23) and that of the Merino was 36.8 (±0.45). Temperament was not associated with dam's age, type of birth or lamb's age. There were no relevant differences in the agitation score between lambs born in 2010 and 2011. The mean of the distribution of possible values of heritability (±s.d.) was 0.18 (±0.05) for the Corriedale and 0.31 (±0.06) for the Merino. The likelihood of heritability values to be greater than 0.15 exceeded 70% in the Corriedale and 90% in the Merino. The temperament of Merino and Corriedale sheep in Uruguay is moderately heritable. It is not related to dam's age, type of birth or age of the lambs; however, it is affected by some aspect of the CG.

Techniques for capturing bighorn sheep lambs

USGS Publications Warehouse

Smith, Joshua B.; Walsh, Daniel P.; Goldstein, Elise J.; Parsons, Zachary D.; Karsch, Rebekah C.; Stiver, Julie R.; Cain, James W.; Raedeke, Kenneth J.; Jenks, Jonathan A.

2014-01-01

Low lamb recruitment is a major challenge facing managers attempting to mitigate the decline of bighorn sheep (Ovis canadensis), and investigations into the underlying mechanisms are limited because of the inability to readily capture and monitor bighorn sheep lambs. We evaluated 4 capture techniques for bighorn sheep lambs: 1) hand-capture of lambs from radiocollared adult females fitted with vaginal implant transmitters (VITs), 2) hand-capture of lambs of intensively monitored radiocollared adult females, 3) helicopter net-gunning, and 4) hand-capture of lambs from helicopters. During 2010–2012, we successfully captured 90% of lambs from females that retained VITs to ≤1 day of parturition, although we noted differences in capture rates between an area of high road density in the Black Hills (92–100%) of South Dakota, USA, and less accessible areas of New Mexico (71%), USA. Retention of VITs was 78% with pre-partum expulsion the main cause of failure. We were less likely to capture lambs from females that expelled VITs ≥1 day of parturition (range = 80–83%) or females that were collared without VITs (range = 60–78%). We used helicopter net-gunning at several sites in 1999, 2001–2002, and 2011, and it proved a useful technique; however, at one site, attempts to capture lambs led to lamb predation by golden eagles (Aquila chrysaetos). We attempted helicopter hand-captures at one site in 1999, and they also were successful in certain circumstances and avoided risk of physical trauma from net-gunning; however, application was limited. In areas of low accessibility or if personnel lack the ability to monitor females and/or VITs for extended periods, helicopter capture may provide a viable option for lamb capture.

Effect of creep-fed supplement on the susceptibility of pasture-grazed suckling lambs to gastrointestinal helminths.

PubMed

de Melo, Gleice Kelli Ayardes; Ítavo, Camila Celeste Brandão Ferreira; Monteiro, Kedma Leonora Silva; da Silva, Jonilson Araújo; da Silva, Pâmila Carolini Gonçalves; Ítavo, Luís Carlos Vinhas; Borges, Dyego Gonçalves Lino; de Almeida Borges, Fernando

2017-05-30

This study evaluated the effect of creep feeding a protein supplement on the susceptibility of suckling lambs to infection with gastrointestinal helminths. Male and female lambs were grazed on Brachiaria spp. pastures next to their mothers. Animals were allocated to one of two treatments: creep feeding (261g/d) and control (no supplementation). The trial period was the suckling of lambs during two years of study: May-October 2013 and March-July 2014. Supplementary creep feeding of lambs improved animal performance (P<0.05). Creep-fed lambs reached 18kg body weight in 64 d, but unsupplemented lambs required 77 d to reach the same weight. Lambs were susceptible to helminth infection during lactation; lambs in both treatments had high fecal egg counts (FECs), with means >1000 eggs per gram, as early as 45days of age, when the daily grazing time per animal increased. Creep feeding reduced the FECs of suckling lambs >60days of age in infections dominated by Haemonchus contortus. Totals of 20 and 48 anthelmintic treatments were administered to the supplemented and unsupplemented animals, respectively. The effect of this variable, however, was significant (P<0.05) only after 60days, when nine and 28 treatments had been administered to the supplemented and unsupplemented lambs, respectively. The number of strongyloid larvae recovered from the paddock did not differ significantly (P >0.05) between the two treatments, indicating similar challenges by infective larvae to both groups. The supplementation of lambs by creep feeding can thus be a strategy for the sustainable control of helminth infection, because it reduces the dependence on anthelmintic treatment. Copyright © 2017. Published by Elsevier B.V.

Growth performance and carcass characteristics of growing ram lambs fed sweet sorghum bagasse-based complete rations varying in roughage-to-concentrate ratios.

PubMed

Kumari, Nagireddy Nalini; Reddy, Yerradoddi Ramana; Blummel, Michel; Nagalakshmi, Devanaboyina; Monika, Thamatam; Reddy, Belum Venkata Subba; Reddy, Chintalapani Ravinder

2013-02-01

Different roughage-to-concentrate ratios of sweet sorghum bagasse (SSB) (a by-product of the biofuel industry)-based complete diets were assessed. Twenty four growing Nellore × Deccani ram lambs aged about 3 months (average body wt., 10.62 ± 0.25 kg) were randomly allotted to four complete rations (CR) varying in roughage-to-concentrate ratios viz. 60:40 (CR-I), 50:50 (CR-II), 40:60 (CR-III) and 30:70(CR-IV) for a period of 180 days. The feed intake was comparable among the lambs fed different experimental complete diets. Average daily weight gain (in grams) was 77.31 ± 4.90, 81.76 ± 5.16, 85.83 ± 2.83 and 86.30 ± 3.25, and feed conversion ratio (in kilograms of feed per kilogram gain) averaged 11.42 ± 0.68, 10.57 ± 0.64, 10.17 ± 0.37 and 9.96 ± 0.38 in ram lambs fed CR-I, CR-II, CR-III and CR-IV rations, respectively. Statistically, differences in daily weight gain and feed conversion ratio among the lambs fed four experimental rations were not significant (P > 0.05). The cost per kilogram gain was significantly (P < 0.01) higher in ram lambs fed CR-IV and CR-III rations compared to CR-I ration, and it was comparable between CR-I and CR-II rations. Dressing percentage averaged 44.90 ± 0.15, 42.57 ± 0.72, 43.67 ± 0.16 and 44.42 ± 0.76 for the respective diets. No significant difference and trend was observed in preslaughter weight, empty body weight, carcass weights, dressing percentage, wholesale cuts and edible and non-edible portions of experimental animals. Similarly, no significant variation could be seen in bone and meat yield (in per cent) and their ratios in various wholesale cuts among the dietary treatments. The roughage-to-concentrate ratio did not affect the chemical composition of meat; however, the fat content of meat was linearly increased with increase in the proportion of concentrate in the diets. The results of the experiment indicated that SSB can be included at 60 % level in the complete diet for economical mutton production from growing Nellore × Deccani ram lambs.

Sodium chlorate reduces presence of Escherichia coli in feces of lambs and ewes managed in shed-lambing systems

USDA-ARS?s Scientific Manuscript database

Our objective was to establish doses of orally-administered NaClO3 that reduced presence of generic Escherichia coli in intestines of ewes and neonatal lambs managed in a shed-lambing system. Neonatal lambs (n = 32; age = 7.1 ± 1.2 d; BW = 6.8 ± 1.0 kg) and yearling ewes (n = 44; BW = 74.8 ± 5.6 kg)...

Lamb and kid mortality in village flocks in the coastal savanna zone of Ghana.

PubMed

Turkson, P K

2003-12-01

A cohort study was designed to observe and follow up mortality in lambs and kids in 88 flocks of sheep and goats under the traditional production system in five villages within the coastal savanna zone of Ghana over a 2-year period. The overall mortality rates for kids and lambs were 30.8% and 33.5%, respectively. Significantly higher proportions of kids (80.2%) and lambs (75.6%) up to 3 months of age died compared to kids and lambs from 4 to 12 months of age. The differences in mortality rates, either between male and female kids and lambs or between single-born and multiple-birth kids and lambs, were not significant. The odds ratio (OR) and relative risks (RR) for lambs and kids, on the basis of sex and birth types, were not significant; neither were the values obtained for attributable risk, attributable fraction, population attributable risk and population attributable fraction. The overall mortality rate on the basis of species of animal was not significant. At the village level, significant differences in the proportions of mortality on the basis of sex were seen in two villages. At Akotokyir, more male lambs (54.2%) died compared to females (27.6%), while at Apewosika more female lambs (42.2%) died compared to males (16.7%). The only significant difference in mortality proportions on the basis of birth type at the village level was seen at Apewosika, where more single-born kids died (52.8%) compared to kids born with sibling(s) (28.4%). The significant ORs for mortalities were 3.10 for male lambs at Akotokyir, 3.35 for female lambs at Apewosika and 2.82 for single-born kids at Apewosika. The corresponding RRs were equally significant. On the basis of species, significantly more lambs died at Akotokyir (44.2%) and Kwesimprah (44.7%) compared to kids. The implications of these findings are discussed.

Fattening ability and carcass value of Dhamari and Tehami ram lambs, F₁ crossbreds of Dhamari × Tehami in Yemen.

PubMed

Al Khewani, Talal; Momani Shaker, Mohamed; Al-Olofi, Samer

2014-12-01

A fattening experiment was carried out to analyze and evaluate the effect of ram lamb genotype on the growth, feed conversion (FC), and carcass value of Dhamari ram lambs, F1 crossbreds of Dhamari × Tehami (F1 DhT), and Tehami ram lambs. Genotype of the ram lambs including the experiment (n = 30) had high significant effect on total weight gain (TWG), average daily gain (ADG), and FC (P < 0.01-0.001). Genotype of the lamb had significant effect on hot and cold dressing percentage (P < 0.001). Also, genotype of the lamb had significant effect on the highest leg percentage (P < 0.001). Furthermore, genotype of the ram lambs had significant effect on musculus longissimus dorsi (MLD) area (P < 0.001). Genotype of the ram lamb had significant effect on TWG, ADG, and FC (P < 0.001). The results of moisture percentage, crude protein percentage, and ash percentage of muscle samples were significantly influenced by ram lamb's genotype (P < 0.001). Fasting live weight and other carcass measurements (hot carcass weight, leg weight, loin weight, shoulder weight, first quality cuts weight) have a positive and highest correlations (P < 0.001). The positive and the highest correlations were found between fasting live weight and hot carcass weight, first quality parts weight. In addition, the positive and the highest correlations were found between hot carcass weight and first quality cuts weight. In general, the results of this study documented that F1 DhT was better than Tehami ram lambs in ADG, TWG, and FC. Additionally, the results show that the feed conversion was in F1 DhT crossbreds ram lambs better than pure Dhamari and Tehami ram lambs, mainly in the carcass indicators.

Enhancing nutritiousness of lamb meat and preventing selenium deficiency.

USDA-ARS?s Scientific Manuscript database

Lamb meat is a naturally flavorful and nutritious product. Our research indicates that feeding a specific wheat-milling coproduct will enhance the nutritiousness of lamb, potentially add monetary value to lamb, and prevent Se deficiency. Selenium is an essential micromineral, and Se supplementation ...

78 FR 31367 - Mandatory Country of Origin Labeling of Beef, Pork, Lamb, Chicken, Goat Meat, Wild and Farm...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-24

...] RIN 0581-AD29 Mandatory Country of Origin Labeling of Beef, Pork, Lamb, Chicken, Goat Meat, Wild and... (including veal), lamb, chicken, goat, and pork; ground beef, ground lamb, ground chicken, ground goat, and...

7 CFR 1280.218 - Exporter.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Assessments § 1280.218 Exporter. Each person exporting live lambs shall remit to the Board an assessment on such lambs at the time of export at the rate...

The impact of genetics on retail meat value in Australian lamb.

PubMed

Anderson, F; Pethick, D W; Gardner, G E

2016-07-01

Lean (muscle), fat, and bone composition of 1554 lamb carcasses from Maternal, Merino and Terminal sired lambs was measured using computed tomography scanning. Lamb sires were diverse in their range of Australian Sheep Breeding Values for post weaning c-site eye muscle depth (PEMD) and fat depth (PFAT), and post weaning weight (PWWT). Lean value, representing predicted lean weight multiplied by retail value, was determined for lambs at the same carcass weight or the same age. At the same carcass weight, lean value was increased the most by reducing sire PFAT, followed by increasing PEMD and PWWT. However for lambs of the same age, increasing sire PWWT increased lean value the most. Terminal sired lambs, on average, had greater lean value irrespective of whether comparisons were made at the same age or weight. Lean value was greater in Merino compared to Maternal sired lambs at equal carcass weight, however the reverse was true when comparisons were made at the same age. Copyright © 2016 Elsevier Ltd. All rights reserved.

Understanding consumers' perception of lamb meat using free word association.

PubMed

de Andrade, Juliana Cunha; de Aguiar Sobral, Louise; Ares, Gastón; Deliza, Rosires

2016-07-01

The aims of the present study were to gather information about Brazilian consumers' perception of lamb meat and to study whether the perception is affected by the consumption frequency of this type of meat. A total of 1025 Brazilian consumers completed word association task with lamb meat. The elicited words were analyzed using inductive coding. Participants' associations with lamb meat were mainly related to sensory characteristics and hedonic attitudes and feelings, indicating that they might be the main motivations for consuming this product. Participants strongly associated lamb meat with special consumption occasions, which suggests that lack of perceived appropriateness for everyday consumption situations might be a barrier for increasing lamb meat consumption. Conceptualization of lamb meat was strongly affected by frequency of consumption of this product. Results from the present work provide a comprehensive insight on Brazilian consumers' perception of lamb meat, which can be used to develop strategies to increase its consumption and improve profitability. Copyright © 2016 Elsevier Ltd. All rights reserved.

Microsatellite based ovine parentage testing to identify the source responsible for the killing of an endangered species.

PubMed

Rendo, Fernando; Iriondo, Mikel; Manzano, Carmen; Estonba, Andone

2011-08-01

In this study, we present an animal forensic genetics case in which we applied ovine microsatellite based parentage testing to the resolution of an act against protected wildlife. The aim was to identify the origin of the animal responsible for the death of an Egyptian vulture (Neophron percnopterus) that had been poisoned through consumption of a Latxa Blond Face breed lamb. Thus, we carried out a 22 microsatellite based parentage test in order to identify the parents of the lamb in the flock which grazes in the same place where the vulture's remains were found. Multiple parentage analysis revealed two possible parents, one ewe and one ram, with a combined paternity/maternity index (PI) higher than 9.09E9 and a likelihood (W) value of 99.9999%, assuming 50% probability a priori. This result confirmed the flock of origin of the poisoned lamb and shows that the microsatellite panel described herein is a potentially useful tool for the resolution of animal forensic cases. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Rapid Multi-Damage Identification for Health Monitoring of Laminated Composites Using Piezoelectric Wafer Sensor Arrays

PubMed Central

Si, Liang; Wang, Qian

2016-01-01

Through the use of the wave reflection from any damage in a structure, a Hilbert spectral analysis-based rapid multi-damage identification (HSA-RMDI) technique with piezoelectric wafer sensor arrays (PWSA) is developed to monitor and identify the presence, location and severity of damage in carbon fiber composite structures. The capability of the rapid multi-damage identification technique to extract and estimate hidden significant information from the collected data and to provide a high-resolution energy-time spectrum can be employed to successfully interpret the Lamb waves interactions with single/multiple damage. Nevertheless, to accomplish the precise positioning and effective quantification of multiple damage in a composite structure, two functional metrics from the RMDI technique are proposed and used in damage identification, which are the energy density metric and the energy time-phase shift metric. In the designed damage experimental tests, invisible damage to the naked eyes, especially delaminations, were detected in the leftward propagating waves as well as in the selected sensor responses, where the time-phase shift spectra could locate the multiple damage whereas the energy density spectra were used to quantify the multiple damage. The increasing damage was shown to follow a linear trend calculated by the RMDI technique. All damage cases considered showed completely the developed RMDI technique potential as an effective online damage inspection and assessment tool. PMID:27153070

Effect of a screen with flaps and straw on behaviour, stress response, productive performance and meat quality in indoor feedlot lambs.

PubMed

Aguayo-Ulloa, L A; Pascual-Alonso, M; Olleta, J L; Sañudo, C; Miranda-de la Lama, G C; María, G A

2015-07-01

We analysed the effect of a modified pen using a wooden screen with flaps and cereal straw as forage and bedding, on behaviour, stress response, performance and meat quality variables of lambs housed in feedlots. Sixty male lambs were placed in enriched (ESF) or conventional (CO) pens (3 pens/treatment, 10 lambs/pen). The CO environment was barren. The ESF lambs showed a great preference for the provided items, which encouraged more natural and richer behaviour, reducing stereotypies and lamb aggressions, and increasing affiliations (P ≤ 0.05), which improves group cohesion. However, ESF lambs also developed a more natural coping style to the handling, evidenced by the higher cortisol levels (65.4 vs. 43.8 nmol/L) and a higher eye temperature as response to the reactivity test (38.1 vs. 37.8 °C). The ESF lambs had a higher (P ≤ 0.05) slaughter weight (27.2 vs. 26.3 kg), conformation score (7.38 vs. 6.07) and pH 24 (5.63 vs. 5.56) but lower cooking losses (12.9 vs. 14.9%) than CO lambs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mutagenicity of basic fractions derived from lamb and beef cooked by common household methods.

PubMed

Barrington, P J; Baker, R S; Truswell, A S; Bonin, A M; Ryan, A J; Paulin, A P

1990-03-01

Mutagen production was examined in lamb and beef in relation to certain common household cooking methods. Mutagenicity was assessed, after extraction of the basic fraction of cooked meat samples, using Salmonella typhimurium strain TA1538 with added rat-liver S-9 homogenate. Little or no mutagenicity was found in barbecued lamb chops, in microwave-cooked lamb chops, sirloin steak, leg of lamb, or rolled beef loaf, in roasted leg of lamb or rolled beef loaf, in stewed blade steak or in boiled chuck steak. However, the basic fraction from well-done, edible fried or grilled meat contained mutagenic activity equivalent to approximately 30,000 TA1538 revertants/100 g cooked meat. It was found tht the mutagenic activity of grilled lamb chops, sirloin and rump steaks was directly related to the average surface temperatures attained during cooking. Use of butter as a frying medium was particularly associated with higher mutagenicity in meat samples. Fried meats (rump and fillet steaks) generally yielded higher mutagenic activity than did grilled meats (rump steak, lamb chops) at comparable temperatures of the cooking medium. Using similar cooking procedures, lamb did not differ markedly from beef in mutagenic activity.

Infrared thermal imaging as a method to evaluate heat loss in newborn lambs.

PubMed

Labeur, L; Villiers, G; Small, A H; Hinch, G N; Schmoelzl, S

2017-12-01

Thermal imaging technology has been identified as a potential method for non-invasive study of thermogenesis in the neonatal lamb. In comparison to measurement of the core body temperature, infrared thermography may observe thermal loss and thermogenesis linked to subcutaneous brown fat depots. This study aimed to identify a suitable method to measure heat loss in the neonatal lamb under a cold challenge. During late pregnancy (day 125), ewes were subjected to either shearing (n=15) or mock handling (sham-shorn for 2min mimicking the shearing movements) (n=15). Previous studies have shown an increase in brown adipose tissue deposition in lambs born to ewes shorn during pregnancy and we hypothesized that the shearing treatment would impact thermoregulatory capacities in newborn lambs. Lambs born to control ewes (n=14; CONTROL) and shorn ewes (n=13; SHORN) were subjected to a cold challenge of 1h duration at 4h after birth. During the cold challenge, thermography images were taken every 10min, from above, at a fixed distance from the dorsal midline. On each image, four fixed-size areas were identified (shoulder, mid loin, hips and rump) and the average and maximum temperatures of each recorded. In all lambs, body surface temperature decreased over time. Overall the SHORN lambs appeared to maintain body surface temperature better than CONTROL lambs, while CONTROL lambs appeared to have higher core temperature. At 30min post cold challenge SHORN lambs tended to have higher body surface temperatures than lambs (P=0.0474). Both average and maximum temperatures were highest at the hips. Average temperature was lowest at the shoulder (P<0.05), while maximum temperatures were lowest at both shoulder and rump (P<0.005). These results indicate that lambs born to shorn ewes maintained their radiated body surface temperature better than CONTROL lambs. In conjunction with core temperature changes under cold challenge, this insight will allow us to understand whether increased body surface temperature contributes to increased overall heat loss or whether increased body surface temperature is indeed a mechanism contributing to maintenance of core body temperature under cold challenge conditions. This study has confirmed the utility of infrared thermography images to capture and identify different levels of thermoregulatory capacity in newborn lambs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Feature and Statistical Model Development in Structural Health Monitoring

NASA Astrophysics Data System (ADS)

Kim, Inho

All structures suffer wear and tear because of impact, excessive load, fatigue, corrosion, etc. in addition to inherent defects during their manufacturing processes and their exposure to various environmental effects. These structural degradations are often imperceptible, but they can severely affect the structural performance of a component, thereby severely decreasing its service life. Although previous studies of Structural Health Monitoring (SHM) have revealed extensive prior knowledge on the parts of SHM processes, such as the operational evaluation, data processing, and feature extraction, few studies have been conducted from a systematical perspective, the statistical model development. The first part of this dissertation, the characteristics of inverse scattering problems, such as ill-posedness and nonlinearity, reviews ultrasonic guided wave-based structural health monitoring problems. The distinctive features and the selection of the domain analysis are investigated by analytically searching the conditions of the uniqueness solutions for ill-posedness and are validated experimentally. Based on the distinctive features, a novel wave packet tracing (WPT) method for damage localization and size quantification is presented. This method involves creating time-space representations of the guided Lamb waves (GLWs), collected at a series of locations, with a spatially dense distribution along paths at pre-selected angles with respect to the direction, normal to the direction of wave propagation. The fringe patterns due to wave dispersion, which depends on the phase velocity, are selected as the primary features that carry information, regarding the wave propagation and scattering. The following part of this dissertation presents a novel damage-localization framework, using a fully automated process. In order to construct the statistical model for autonomous damage localization deep-learning techniques, such as restricted Boltzmann machine and deep belief network, are trained and utilized to interpret nonlinear far-field wave patterns. Next, a novel bridge scour estimation approach that comprises advantages of both empirical and data-driven models is developed. Two field datasets from the literature are used, and a Support Vector Machine (SVM), a machine-learning algorithm, is used to fuse the field data samples and classify the data with physical phenomena. The Fast Non-dominated Sorting Genetic Algorithm (NSGA-II) is evaluated on the model performance objective functions to search for Pareto optimal fronts.

Lambs Fed Fresh Winter Forage Rape (Brassica napus L.) Emit Less Methane than Those Fed Perennial Ryegrass (Lolium perenne L.), and Possible Mechanisms behind the Difference

PubMed Central

Sun, Xuezhao; Henderson, Gemma; Cox, Faith; Molano, German; Harrison, Scott J.; Luo, Dongwen; Janssen, Peter H.; Pacheco, David

2015-01-01

The objectives of this study were to examine long-term effects of feeding forage rape (Brassica napus L.) on methane yields (g methane per kg of feed dry matter intake), and to propose mechanisms that may be responsible for lower emissions from lambs fed forage rape compared to perennial ryegrass (Lolium perenne L.). The lambs were fed fresh winter forage rape or ryegrass as their sole diet for 15 weeks. Methane yields were measured using open circuit respiration chambers, and were 22-30% smaller from forage rape than from ryegrass (averages of 13.6 g versus 19.5 g after 7 weeks, and 17.8 g versus 22.9 g after 15 weeks). The difference therefore persisted consistently for at least 3 months. The smaller methane yields from forage rape were not related to nitrate or sulfate in the feed, which might act as alternative electron acceptors, or to the levels of the potential inhibitors glucosinolates and S-methyl L-cysteine sulfoxide. Ruminal microbial communities in forage rape-fed lambs were different from those in ryegrass-fed lambs, with greater proportions of potentially propionate-forming bacteria, and were consistent with less hydrogen and hence less methane being produced during fermentation. The molar proportions of ruminal acetate were smaller and those of propionate were greater in forage rape-fed lambs, consistent with the larger propionate-forming populations and less hydrogen production. Forage rape contained more readily fermentable carbohydrates and less structural carbohydrates than ryegrass, and was more rapidly degraded in the rumen, which might favour this fermentation profile. The ruminal pH was lower in forage rape-fed lambs, which might inhibit methanogenic activity, shifting the rumen fermentation to more propionate and less hydrogen and methane. The significance of these two mechanisms remains to be investigated. The results suggest that forage rape is a potential methane mitigation tool in pastoral-based sheep production systems. PMID:25803688

Interception of the development of self tolerance in fetal lambs.

PubMed

McCullagh, P

1989-08-01

Investigation of the nature of immunological self tolerance has usually relied upon experimental protocols in which the tolerant state is interrupted in mature animals with the production of autoimmune disease. While such research has improved the understanding of those processes operative in overt autoimmunity, it has not been informative in relation to events associated with the establishment of self tolerance. Any description of this state which is to be based on observation will necessitate the use of experimental systems that permit observation of animals during the development of self tolerance. The present experiment entailed intervention approximately one third of the way through the gestation period of fetal lambs. An earlier experiment had established that 54-day fetal lambs would accept allografts of adult skin. This indicated that the capacity to discriminate between self and non-self had not been acquired at that age. Fetuses at this stage of gestation were submitted to either partial or total removal of the thyroid gland. The excised tissue was then implanted in nude mice for periods of 5 to 9 weeks. It was subsequently replaced subcutaneously, either in the original donor or in another fetus at a comparable stage of gestation. At postmortem examination, several weeks later, self implants in lambs from which the thyroid gland had been completely removed displayed autoimmune thyroiditis of varying degrees of severity. However, self implants in partially thyroidectomized animals were uniformly free from autoimmune manifestations. This implied that these reactions had not been directed against contaminating murine tissues in the implants replaced in completely thyroidectomized lambs. All allogeneic implants were subject to vey heavy lymphocytic infiltration, usually with accompanying necrosis consistent with allograft rejection. This was taken as an indication that hypothyroid fetal lambs had become immunocompetent by the time of thyroid reimplantation. Spontaneous immunological reactivity against reimplanted self thyroid tissue by thyroidectomized lambs was interpreted as a failure to acquire the capacity for self recognition as a result of antigen deprivation.

Haemodynamic effects of umbilical cord milking in premature sheep during the neonatal transition.

PubMed

Blank, Douglas A; Polglase, Graeme R; Kluckow, Martin; Gill, Andrew William; Crossley, Kelly J; Moxham, Alison; Rodgers, Karyn; Zahra, Valerie; Inocencio, Ishmael; Stenning, Fiona; LaRosa, Domeic A; Davis, Peter G; Hooper, Stuart B

2017-12-05

Umbilical cord milking (UCM) at birth may benefit preterm infants, but the physiological effects of UCM are unknown. We compared the physiological effects of two UCM strategies with immediate umbilical cord clamping (UCC) and physiological-based cord clamping (PBCC) in preterm lambs. At 126 days' gestational age, fetal lambs were exteriorised, intubated and instrumented to measure umbilical, pulmonary and cerebral blood flows and arterial pressures. Lambs received either (1) UCM without placental refill (UCMwoPR); (2) UCM with placental refill (UCMwPR); (3) PBCC, whereby ventilation commenced prior to UCC; or (4) immediate UCC. UCM involved eight milks along a 10 cm length of cord, followed by UCC. A net volume of blood was transferred into the lamb during UCMwPR (8.8 mL/kg, IQR 8-10, P=0.01) but not during UCMwoPR (0 mL/kg, IQR -2.8 to 1.7) or PBCC (1.1 mL/kg, IQR -1.3 to 4.3). UCM had no effect on pulmonary blood flow, but caused large fluctuations in mean carotid artery pressures (MBP) and blood flows (CABF). In UCMwoPR and UCMwPR lambs, MBP increased by 12%±1% and 8%±1% and CABF increased by 32%±2% and 15%±2%, respectively, with each milk. Cerebral oxygenation decreased the least in PBCC lambs (17%, IQR 13-26) compared with UCMwoPR (26%, IQR 23-25, P=0.03), UCMwPR (35%, IQR 27-44, P=0.02) and immediate UCC (34%, IQR 28-41, P=0.02) lambs. UCMwoPR failed to provide placental transfusion, and UCM strategies caused considerable haemodynamic disturbance. UCM does not provide the same physiological benefits of PBCC. Further review of UCM is warranted before adoption into routine clinical practice. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Determination of maternal pedigree and ewe-lamb spatial relationships by application of Bluetooth technology in extensive farming systems.

PubMed

Sohi, R; Trompf, J; Marriott, H; Bervan, A; Godoy, B I; Weerasinghe, M; Desai, A; Jois, M

2017-11-01

The objectives of this study were to validate the application of Bluetooth technology to determine maternal pedigree and to determine ewe-lamb spatial relationships in extensive farming systems. A total of 35 first-cross Merino ewes (Merino × Border Leicester and East Friesian) and 23 of their lambs aged 1 to 3 wk were fitted with activity monitors equipped with Bluetooth (BT) technology (ActiGraph wGT3X-BT) by means of halters and collars, respectively. The BT devices on lambs were programmed to receive wireless signals once every minute from nearby BT units on ewes, which were programmed as beacons sending BT signals 4 times every second. Ewes and lambs fitted with sensors were dispatched into the paddocks, and after 10 d, the sensor units were retrieved and the BT signals received by lambs were downloaded using the ActiGraph software. The maternal pedigree of the lambs was determined as the ewe from which the lamb received the most BT signals. The distance between the lamb receiving the signal and the ewe sending the signal was estimated from the strength of BT signal received. The pedigree determined by BT was compared with the pedigree determined by DNA profiling and verification. The results showed that the accuracy of maternal pedigree determined by BT signals reached 100% within the first 15 min of returning animals to pasture of ewes and lambs fitted with sensors. Maternal signals (counts/d) received by 1-, 2-, and 3-wk-old lambs were 617 ± 102, 603 ± 54, and 498 ± 36, respectively, and the corresponding nonmaternal signals received were 140 ± 27, 106 ± 30, and 155 ± 39, respectively. Maternal signals received during the dark period were significantly higher than the maternal signals received during the light period ( < 0.05). Maternal signals received during the light period by 3-wk-old lambs were significantly lower when compared with those received by 1- and 2-wk-old lambs. Over 90% of the BT signals received from within 2 m of the lamb were from its mother. The maternal BT signals expressed as a portion of total BT signals decreased with increasing distance from the lamb. The results show that BT wireless networking is a fast and reliable method for the determination of maternal pedigree of lambs in extensive farming systems. In addition, wireless BT technology is also useful in determining mother-offspring spatial relationships.