Comparison of charged nanoparticle concentrations near busy roads and overhead high-voltage power lines.

PubMed

Jayaratne, E R; Ling, X; Morawska, L

2015-09-01

Overhead high-voltage power lines are known sources of corona ions. These ions rapidly attach to aerosols to form charged particles in the environment. Although the effect of ions and charged particles on human health is largely unknown, much attention has focused on the increasing exposure as a result of the expanding power network in urban residential areas. However, it is not widely known that a large number of charged particles in urban environments originate from motor vehicle emissions. In this study, for the first time, we compare the concentrations of charged nanoparticles near busy roads and overhead power lines. We show that large concentrations of both positive and negative charged nanoparticles are present near busy roadways and that these concentrations commonly exceed those under high-voltage power lines. We estimate that the concentration of charged nanoparticles found near two freeways carrying around 120 vehicles per minute exceeded the corresponding maximum concentrations under two corona-emitting overhead power lines by as much as a factor of 5. The difference was most pronounced when a significant fraction of traffic consisted of heavy-duty diesel vehicles which typically have high particle and charge emission rates. Copyright © 2015 Elsevier B.V. All rights reserved.

Lightning and surge protection of large ground facilities

NASA Astrophysics Data System (ADS)

Stringfellow, Michael F.

1988-04-01

The vulnerability of large ground facilities to direct lightning strikes and to lightning-induced overvoltages on the power distribution, telephone and data communication lines are discussed. Advanced electrogeometric modeling is used for the calculation of direct strikes to overhead power lines, buildings, vehicles and objects within the facility. Possible modes of damage, injury and loss are discussed. Some appropriate protection methods for overhead power lines, structures, vehicles and aircraft are suggested. Methods to mitigate the effects of transients on overhead and underground power systems as well as within buildings and other structures are recommended. The specification and location of low-voltage surge suppressors for the protection of vulnerable hardware such as computers, telecommunication equipment and radar installations are considered. The advantages and disadvantages of commonly used grounding techniques, such as single point, multiple and isolated grounds are compared. An example is given of the expected distribution of lightning flashes to a large airport, its buildings, structures and facilities, as well as to vehicles on the ground.

Business Activity Monitoring: Real-Time Group Goals and Feedback Using an Overhead Scoreboard in a Distribution Center

ERIC Educational Resources Information Center

Goomas, David T.; Smith, Stuart M.; Ludwig, Timothy D.

2011-01-01

Companies operating large industrial settings often find delivering timely and accurate feedback to employees to be one of the toughest challenges they face in implementing performance management programs. In this report, an overhead scoreboard at a retailer's distribution center informed teams of order selectors as to how many tasks were…

A Temporal Credential-Based Mutual Authentication with Multiple-Password Scheme for Wireless Sensor Networks

PubMed Central

Zhang, Ruisheng; Liu, Qidong

2017-01-01

Wireless sensor networks (WSNs), which consist of a large number of sensor nodes, have become among the most important technologies in numerous fields, such as environmental monitoring, military surveillance, control systems in nuclear reactors, vehicle safety systems, and medical monitoring. The most serious drawback for the widespread application of WSNs is the lack of security. Given the resource limitation of WSNs, traditional security schemes are unsuitable. Approaches toward withstanding related attacks with small overhead have thus recently been studied by many researchers. Numerous studies have focused on the authentication scheme for WSNs, but most of these works cannot achieve the security performance and overhead perfectly. Nam et al. proposed a two-factor authentication scheme with lightweight sensor computation for WSNs. In this paper, we review this scheme, emphasize its drawbacks, and propose a temporal credential-based mutual authentication with a multiple-password scheme for WSNs. Our scheme uses multiple passwords to achieve three-factor security performance and generate a session key between user and sensor nodes. The security analysis phase shows that our scheme can withstand related attacks, including a lost password threat, and the comparison phase shows that our scheme involves a relatively small overhead. In the comparison of the overhead phase, the result indicates that more than 95% of the overhead is composed of communication and not computation overhead. Therefore, the result motivates us to pay further attention to communication overhead than computation overhead in future research. PMID:28135288

A Temporal Credential-Based Mutual Authentication with Multiple-Password Scheme for Wireless Sensor Networks.

PubMed

Liu, Xin; Zhang, Ruisheng; Liu, Qidong

2017-01-01

Wireless sensor networks (WSNs), which consist of a large number of sensor nodes, have become among the most important technologies in numerous fields, such as environmental monitoring, military surveillance, control systems in nuclear reactors, vehicle safety systems, and medical monitoring. The most serious drawback for the widespread application of WSNs is the lack of security. Given the resource limitation of WSNs, traditional security schemes are unsuitable. Approaches toward withstanding related attacks with small overhead have thus recently been studied by many researchers. Numerous studies have focused on the authentication scheme for WSNs, but most of these works cannot achieve the security performance and overhead perfectly. Nam et al. proposed a two-factor authentication scheme with lightweight sensor computation for WSNs. In this paper, we review this scheme, emphasize its drawbacks, and propose a temporal credential-based mutual authentication with a multiple-password scheme for WSNs. Our scheme uses multiple passwords to achieve three-factor security performance and generate a session key between user and sensor nodes. The security analysis phase shows that our scheme can withstand related attacks, including a lost password threat, and the comparison phase shows that our scheme involves a relatively small overhead. In the comparison of the overhead phase, the result indicates that more than 95% of the overhead is composed of communication and not computation overhead. Therefore, the result motivates us to pay further attention to communication overhead than computation overhead in future research.

Penny Pettigrew in the Payload Operations Integration Center

NASA Image and Video Library

2017-11-09

Penny Pettigrew chats in real time with a space station crew member conducting an experiment in microgravity some 250 miles overhead. The Payload Operations Integration Center cadre monitor science communications on station 24 hours a day, seven days a week, 365 days per year.

Using the High-Level Based Program Interface to Facilitate the Large Scale Scientific Computing

PubMed Central

Shang, Yizi; Shang, Ling; Gao, Chuanchang; Lu, Guiming; Ye, Yuntao; Jia, Dongdong

2014-01-01

This paper is to make further research on facilitating the large-scale scientific computing on the grid and the desktop grid platform. The related issues include the programming method, the overhead of the high-level program interface based middleware, and the data anticipate migration. The block based Gauss Jordan algorithm as a real example of large-scale scientific computing is used to evaluate those issues presented above. The results show that the high-level based program interface makes the complex scientific applications on large-scale scientific platform easier, though a little overhead is unavoidable. Also, the data anticipation migration mechanism can improve the efficiency of the platform which needs to process big data based scientific applications. PMID:24574931

Efficient Load Balancing and Data Remapping for Adaptive Grid Calculations

NASA Technical Reports Server (NTRS)

Oliker, Leonid; Biswas, Rupak

1997-01-01

Mesh adaption is a powerful tool for efficient unstructured- grid computations but causes load imbalance among processors on a parallel machine. We present a novel method to dynamically balance the processor workloads with a global view. This paper presents, for the first time, the implementation and integration of all major components within our dynamic load balancing strategy for adaptive grid calculations. Mesh adaption, repartitioning, processor assignment, and remapping are critical components of the framework that must be accomplished rapidly and efficiently so as not to cause a significant overhead to the numerical simulation. Previous results indicated that mesh repartitioning and data remapping are potential bottlenecks for performing large-scale scientific calculations. We resolve these issues and demonstrate that our framework remains viable on a large number of processors.

VME rollback hardware for time warp multiprocessor systems

NASA Technical Reports Server (NTRS)

Robb, Michael J.; Buzzell, Calvin A.

1992-01-01

The purpose of the research effort is to develop and demonstrate innovative hardware to implement specific rollback and timing functions required for efficient queue management and precision timekeeping in multiprocessor discrete event simulations. The previously completed phase 1 effort demonstrated the technical feasibility of building hardware modules which eliminate the state saving overhead of the Time Warp paradigm used in distributed simulations on multiprocessor systems. The current phase 2 effort will build multiple pre-production rollback hardware modules integrated with a network of Sun workstations, and the integrated system will be tested by executing a Time Warp simulation. The rollback hardware will be designed to interface with the greatest number of multiprocessor systems possible. The authors believe that the rollback hardware will provide for significant speedup of large scale discrete event simulation problems and allow multiprocessors using Time Warp to dramatically increase performance.

Rehabilitation of the Overhead Athlete’s Elbow

PubMed Central

Wilk, Kevin E.; Macrina, Leonard C.; Cain, E. Lyle; Dugas, Jeffrey R.; Andrews, James R.

2012-01-01

The activities required during overhead sports, particularly during baseball pitching, produce large forces at the elbow joint. Injuries to the elbow joint frequently occur in the overhead athlete because of the large amount of forces observed during the act of throwing, playing tennis, or playing golf. Injuries may result because of repetitive overuse, leading to tissue failure. Rehabilitation following injury or surgery to the throwing elbow is vital to fully restore normal function and return the athlete to competition as quickly and safely as possible. Rehabilitation of the elbow, whether following injury or postsurgical, must follow a progressive and sequential order, building on the previous phase, to ensure that healing tissues are not compromised. Emphasis is placed on restoring full motion, muscular strength, and neuromuscular control while gradually applying loads to healing tissue. In addition, when one is creating a rehabilitation plan for athletes, it is imperative to treat the entire upper extremity, core, and legs to create and dissipate the forces generated at each joint. PMID:23016113

Hybrid-optimization strategy for the communication of large-scale Kinetic Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Wu, Baodong; Li, Shigang; Zhang, Yunquan; Nie, Ningming

2017-02-01

The parallel Kinetic Monte Carlo (KMC) algorithm based on domain decomposition has been widely used in large-scale physical simulations. However, the communication overhead of the parallel KMC algorithm is critical, and severely degrades the overall performance and scalability. In this paper, we present a hybrid optimization strategy to reduce the communication overhead for the parallel KMC simulations. We first propose a communication aggregation algorithm to reduce the total number of messages and eliminate the communication redundancy. Then, we utilize the shared memory to reduce the memory copy overhead of the intra-node communication. Finally, we optimize the communication scheduling using the neighborhood collective operations. We demonstrate the scalability and high performance of our hybrid optimization strategy by both theoretical and experimental analysis. Results show that the optimized KMC algorithm exhibits better performance and scalability than the well-known open-source library-SPPARKS. On 32-node Xeon E5-2680 cluster (total 640 cores), the optimized algorithm reduces the communication time by 24.8% compared with SPPARKS.

How localized is ``local?'' Efficiency vs. accuracy of O(N) domain decomposition in local orbital based all-electron electronic structure theory

NASA Astrophysics Data System (ADS)

Havu, Vile; Blum, Volker; Scheffler, Matthias

2007-03-01

Numeric atom-centered local orbitals (NAO) are efficient basis sets for all-electron electronic structure theory. The locality of NAO's can be exploited to render (in principle) all operations of the self-consistency cycle O(N). This is straightforward for 3D integrals using domain decomposition into spatially close subsets of integration points, enabling critical computational savings that are effective from ˜tens of atoms (no significant overhead for smaller systems) and make large systems (100s of atoms) computationally feasible. Using a new all-electron NAO-based code,^1 we investigate the quantitative impact of exploiting this locality on two distinct classes of systems: Large light-element molecules [Alanine-based polypeptide chains (Ala)n], and compact transition metal clusters. Strict NAO locality is achieved by imposing a cutoff potential with an onset radius rc, and exploited by appropriately shaped integration domains (subsets of integration points). Conventional tight rc<= 3å have no measurable accuracy impact in (Ala)n, but introduce inaccuracies of 20-30 meV/atom in Cun. The domain shape impacts the computational effort by only 10-20 % for reasonable rc. ^1 V. Blum, R. Gehrke, P. Havu, V. Havu, M. Scheffler, The FHI Ab Initio Molecular Simulations (aims) Project, Fritz-Haber-Institut, Berlin (2006).

Automatically identifying health- and clinical-related content in wikipedia.

PubMed

Liu, Feifan; Moosavinasab, Soheil; Agarwal, Shashank; Bennett, Andrew S; Yu, Hong

2013-01-01

Physicians are increasingly using the Internet for finding medical information related to patient care. Wikipedia is a valuable online medical resource to be integrated into existing clinical question answering (QA) systems. On the other hand, Wikipedia contains a full spectrum of world's knowledge and therefore comprises a large partition of non-health-related content, which makes disambiguation more challenging and consequently leads to large overhead for existing systems to effectively filter irrelevant information. To overcome this, we have developed both unsupervised and supervised approaches to identify health-related articles as well as clinically relevant articles. Furthermore, we explored novel features by extracting health related hierarchy from the Wikipedia category network, from which a variety of features were derived and evaluated. Our experiments show promising results and also demonstrate that employing the category hierarchy can effectively improve the system performance.

Deployment/retraction ground testing of a large flexible solar array

NASA Technical Reports Server (NTRS)

Chung, D. T.

1982-01-01

The simulated zero-gravity ground testing of the flexible fold-up solar array consisting of eighty-four full-size panels (.368 m x .4 m each) is addressed. Automatic, hands-off extension, retraction, and lockup operations are included. Three methods of ground testing were investigated: (1) vertical testing; (2) horizontal testing, using an overhead water trough to support the panels; and (3) horizontal testing, using an overhead track in conjunction with a counterweight system to support the panels. Method 3 was selected as baseline. The wing/assembly vertical support structure, the five-tier overhead track, and the mast-element support track comprise the test structure. The flexible solar array wing assembly was successfully extended and retracted numerous times under simulated zero-gravity conditions.

Implantable electronics: emerging design issues and an ultra light-weight security solution.

PubMed

Narasimhan, Seetharam; Wang, Xinmu; Bhunia, Swarup

2010-01-01

Implantable systems that monitor biological signals require increasingly complex digital signal processing (DSP) electronics for real-time in-situ analysis and compression of the recorded signals. While it is well-known that such signal processing hardware needs to be implemented under tight area and power constraints, new design requirements emerge with their increasing complexity. Use of nanoscale technology shows tremendous benefits in implementing these advanced circuits due to dramatic improvement in integration density and power dissipation per operation. However, it also brings in new challenges such as reliability and large idle power (due to higher leakage current). Besides, programmability of the device as well as security of the recorded information are rapidly becoming major design considerations of such systems. In this paper, we analyze the emerging issues associated with the design of the DSP unit in an implantable system. Next, we propose a novel ultra light-weight solution to address the information security issue. Unlike the conventional information security approaches like data encryption, which come at large area and power overhead and hence are not amenable for resource-constrained implantable systems, we propose a multilevel key-based scrambling algorithm, which exploits the nature of the biological signal to effectively obfuscate it. Analysis of the proposed algorithm in the context of neural signal processing and its hardware implementation shows that we can achieve high level of security with ∼ 13X lower power and ∼ 5X lower area overhead than conventional cryptographic solutions.

Parallel network simulations with NEURON.

PubMed

Migliore, M; Cannia, C; Lytton, W W; Markram, Henry; Hines, M L

2006-10-01

The NEURON simulation environment has been extended to support parallel network simulations. Each processor integrates the equations for its subnet over an interval equal to the minimum (interprocessor) presynaptic spike generation to postsynaptic spike delivery connection delay. The performance of three published network models with very different spike patterns exhibits superlinear speedup on Beowulf clusters and demonstrates that spike communication overhead is often less than the benefit of an increased fraction of the entire problem fitting into high speed cache. On the EPFL IBM Blue Gene, almost linear speedup was obtained up to 100 processors. Increasing one model from 500 to 40,000 realistic cells exhibited almost linear speedup on 2,000 processors, with an integration time of 9.8 seconds and communication time of 1.3 seconds. The potential for speed-ups of several orders of magnitude makes practical the running of large network simulations that could otherwise not be explored.

Parallel Network Simulations with NEURON

PubMed Central

Migliore, M.; Cannia, C.; Lytton, W.W; Markram, Henry; Hines, M. L.

2009-01-01

The NEURON simulation environment has been extended to support parallel network simulations. Each processor integrates the equations for its subnet over an interval equal to the minimum (interprocessor) presynaptic spike generation to postsynaptic spike delivery connection delay. The performance of three published network models with very different spike patterns exhibits superlinear speedup on Beowulf clusters and demonstrates that spike communication overhead is often less than the benefit of an increased fraction of the entire problem fitting into high speed cache. On the EPFL IBM Blue Gene, almost linear speedup was obtained up to 100 processors. Increasing one model from 500 to 40,000 realistic cells exhibited almost linear speedup on 2000 processors, with an integration time of 9.8 seconds and communication time of 1.3 seconds. The potential for speed-ups of several orders of magnitude makes practical the running of large network simulations that could otherwise not be explored. PMID:16732488

1 μm-thickness ultra-flexible and high electrode-density surface electromyogram measurement sheet with 2 V organic transistors for prosthetic hand control.

PubMed

Fuketa, Hiroshi; Yoshioka, Kazuaki; Shinozuka, Yasuhiro; Ishida, Koichi; Yokota, Tomoyuki; Matsuhisa, Naoji; Inoue, Yusuke; Sekino, Masaki; Sekitani, Tsuyoshi; Takamiya, Makoto; Someya, Takao; Sakurai, Takayasu

2014-12-01

A 64-channel surface electromyogram (EMG) measurement sheet (SEMS) with 2 V organic transistors on a 1 μm-thick ultra-flexible polyethylene naphthalate (PEN) film is developed for prosthetic hand control. The surface EMG electrodes must satisfy the following three requirements; high mechanical flexibility, high electrode density and high signal integrity. To achieve high electrode density and high signal integrity, a distributed and shared amplifier (DSA) architecture is proposed, which enables an in-situ amplification of the myoelectric signal with a fourfold increase in EMG electrode density. In addition, a post-fabrication select-and-connect (SAC) method is proposed to cope with the large mismatch of organic transistors. The proposed SAC method reduces the area and the power overhead by 96% and 98.2%, respectively, compared with the use of conventional parallel transistors to reduce the transistor mismatch by a factor of 10.

Relationship Between the Electromagnetic Wave Energy Coupled by Overhead Lines and the Radiation Source Current Explored in the Laboratory

NASA Astrophysics Data System (ADS)

Li, Xiangchao; Wan, Zhicheng

2018-04-01

In order to solve the damage and interference problems to the electronic devices, which are induced by overvoltage excited by the coupling process between lightning electromagnetic wave and overhead lines, the lightning channel is set to be equivalent to a radiant wire antenna. Based on the integration model of lightning return stroke channel, transmission line, and ground, we take advantage of the derived formula gotten from the transmission line model. By combing the theoretical and experimental methods, we conduct a comparative analysis on the coupling process between natural/simulated lightning and overhead line. Besides, we also calculate the amplitude and energy of overvoltage, which is caused by the coupling process between lightning electromagnetic wave and overhead lines. Upon these experimental results, we can draw several conclusions as follows: when the amplitude of the lightning current in the channel is between 5 kA and 41 kA, it takes on an excellent linear relation between the amplitude of overvoltage and the magnitude of the lightning current, the relation between coupling energy and magnitude of the lightning current takes on an exponential trend. When lightning wave transmits on the transmission lines, the high-order mode will be excited. Through analysis on the high-order mode's characteristics, we find that the theoretical analysis is consistent with the experimental results, which has a certain reference value to the protection on overhead lines.

Hierarchical auto-configuration addressing in mobile ad hoc networks (HAAM)

NASA Astrophysics Data System (ADS)

Ram Srikumar, P.; Sumathy, S.

2017-11-01

Addressing plays a vital role in networking to identify devices uniquely. A device must be assigned with a unique address in order to participate in the data communication in any network. Different protocols defining different types of addressing are proposed in literature. Address auto-configuration is a key requirement for self organizing networks. Existing auto-configuration based addressing protocols require broadcasting probes to all the nodes in the network before assigning a proper address to a new node. This needs further broadcasts to reflect the status of the acquired address in the network. Such methods incur high communication overheads due to repetitive flooding. To address this overhead, a new partially stateful address allocation scheme, namely Hierarchical Auto-configuration Addressing (HAAM) scheme is extended and proposed. Hierarchical addressing basically reduces latency and overhead caused during address configuration. Partially stateful addressing algorithm assigns addresses without the need for flooding and global state awareness, which in turn reduces the communication overhead and space complexity respectively. Nodes are assigned addresses hierarchically to maintain the graph of the network as a spanning tree which helps in effectively avoiding the broadcast storm problem. Proposed algorithm for HAAM handles network splits and merges efficiently in large scale mobile ad hoc networks incurring low communication overheads.

Clomp

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gylenhaal, J.; Bronevetsky, G.

2007-05-25

CLOMP is the C version of the Livermore OpenMP benchmark deeloped to measure OpenMP overheads and other performance impacts due to threading (like NUMA memory layouts, memory contention, cache effects, etc.) in order to influence future system design. Current best-in-class implementations of OpenMP have overheads at least ten times larger than is required by many of our applications for effective use of OpenMP. This benchmark shows the significant negative performance impact of these relatively large overheads and of other thread effects. The CLOMP benchmark highly configurable to allow a variety of problem sizes and threading effects to be studied andmore » it carefully checks its results to catch many common threading errors. This benchmark is expected to be included as part of the Sequoia Benchmark suite for the Sequoia procurement.« less

A new method for overhead drilling.

PubMed

Rempel, David; Star, Demetra; Barr, Alan; Gibbons, Billy; Janowitz, Ira

2009-12-01

In the construction sector, overhead drilling into concrete or metal ceilings is a strenuous task associated with shoulder, neck and back musculoskeletal disorders due to the large applied forces and awkward arm postures. Two intervention devices, an inverted drill press and a foot lever design, were developed then compared to the usual method by construction workers performing their normal overhead drilling activities (n = 14). While the intervention devices were rated as less fatiguing than the usual method, their ratings on usability measures were worse than the usual method. The study demonstrates that the intervention devices can reduce fatigue; however, additional modifications are necessary in order to improve usability and productivity. Devices designed to improve workplace safety may need to undergo several rounds of field testing and modification prior to implementation.

Cooperation among wirelessly connected static and mobile sensor nodes for surveillance applications.

PubMed

de Freitas, Edison Pignaton; Heimfarth, Tales; Vinel, Alexey; Wagner, Flávio Rech; Pereira, Carlos Eduardo; Larsson, Tony

2013-09-25

This paper presents a bio-inspired networking strategy to support the cooperation between static sensors on the ground and mobile sensors in the air to perform surveillance missions in large areas. The goal of the proposal is to provide low overhead in the communication among sensor nodes, while allocating the mobile sensors to perform sensing activities requested by the static ones. Simulations have shown that the strategy is efficient in maintaining low overhead and achieving the desired coordination.

S3/S4 Integrated Truss being moved into the Space Shuttle Payloa

NASA Image and Video Library

2007-02-07

In the Space Station Processing Facility, an overhead crane moves the S3/S4 integrated truss to a payload canister. After it is stowed in the canister, the S3/S4 truss will be transported to the launch pad. The truss is the payload on mission STS-117, targeted for launch on March 15.

S3/S4 Integrated Truss being moved into the Space Shuttle Payloa

NASA Image and Video Library

2007-02-07

In the Space Station Processing Facility, an overhead crane settles the S3/S4 integrated truss into the payload canister. After it is stowed in the canister, the S3/S4 truss will be transported to the launch pad. The truss is the payload on mission STS-117, targeted for launch on March 15.

A Double Dwell High Sensitivity GPS Acquisition Scheme Using Binarized Convolution Neural Network

PubMed Central

Wang, Zhen; Zhuang, Yuan; Yang, Jun; Zhang, Hengfeng; Dong, Wei; Wang, Min; Hua, Luchi; Liu, Bo; Shi, Longxing

2018-01-01

Conventional GPS acquisition methods, such as Max selection and threshold crossing (MAX/TC), estimate GPS code/Doppler by its correlation peak. Different from MAX/TC, a multi-layer binarized convolution neural network (BCNN) is proposed to recognize the GPS acquisition correlation envelope in this article. The proposed method is a double dwell acquisition in which a short integration is adopted in the first dwell and a long integration is applied in the second one. To reduce the search space for parameters, BCNN detects the possible envelope which contains the auto-correlation peak in the first dwell to compress the initial search space to 1/1023. Although there is a long integration in the second dwell, the acquisition computation overhead is still low due to the compressed search space. Comprehensively, the total computation overhead of the proposed method is only 1/5 of conventional ones. Experiments show that the proposed double dwell/correlation envelope identification (DD/CEI) neural network achieves 2 dB improvement when compared with the MAX/TC under the same specification. PMID:29747373

Evaluating Effects of H2O and overhead O3 on Global Mean Tropospheric OH Concentration

NASA Technical Reports Server (NTRS)

Nicely, Julie M.; Salawitch, R.J.; Canty, T.; Lang, Chang; Duncan, Bryan; Liang, Qing; Oman, Luke David; Stolarski, Richard S.; Waugh, Darryn

2012-01-01

The oxidizing capacity of the troposphere is controlled, to a large extent, by the abundance of hydroxyl radical (OH). The global mean concentration of OH, [OH]GLOBAL, inferred from measurements of methyl chloroform, has remained relatively constant during the past several decades, despite rising levels of CH4 that should have led to a steady decline. Here we examine other factors that may have affected [OH]GLOBAL, such as the overhead burden of stratospheric O3 and tropospheric H2O, using global OH fields from the GEOS-CHEM Chemistry-Climate Model. Our analysis suggests these factors may have contributed a positive trend to [OH]GLOBAL large enough to counter the decrease due to CH4.

Douglas flight deck design philosophy

NASA Technical Reports Server (NTRS)

Oldale, Paul

1990-01-01

The systems experience gained from 17 years of DC-10 operation was used during the design of the MD-11 to automate system operation and reduce crew workload. All functions, from preflight to shutdown at the termination of flight, require little input from the crew. The MD-11 aircraft systems are monitored for proper operation by the Aircraft Systems Controllers (ASC). In most cases, system reconfiguration as a result of a malfunction is automated. Manual input is required for irreversible actions such as engine shutdown, fuel dump, fire agent discharge, or Integrated Drive Generator (IDG) disconnect. During normal operations, when the cockpit is configured for flight, all annunciators on the overhead panel will be extinguished. This Dark Cockpit immediately confirms to the crew that the panels are correctly configured and that no abnormalities are present. Primary systems annunciations are shown in text on the Alert Area of the Engine and Alert Display (EAD). This eliminates the need to scan the overhead. The MD-11 aircraft systems can be manually controlled from the overhead area of the cockpit. The center portion of the overhead panel is composed of the primary aircraft systems panels, which include FUEL, AIR, Electrical (ELEC) and Hydraulic (HYD) systems, which are easily accessible from both flight crew positions. Each Aircraft Systems Controller (ASC) has two automatic channels and a manual mode. All rectangular lights are annunciators. All square lights are combined switches and annunciators called switch/lights. Red switch/lights on the overhead (Level 3 alerts) are for conditions requiring immediate crew action. Amber (Level 2 or Level 1 alerts) indicates a fault or switch out of position requiring awareness or crew interaction. Overhead switches used in normal operating conditions will illuminate blue when in use (Level 0 alerts) such as WING ANTI-ICE - ON. An overhead switch/light with BLACK LETTERING on an amber or red background indicates a system failure and that crew interaction is required. A switch/light with blue or amber lettering and a BLACK BACKGROUND indicates a switch out of normal position and that crew action is necessary only if the system is in manual operation.

S3/S4 Integrated Truss being moved into the Space Shuttle Payloa

NASA Image and Video Library

2007-02-07

In the Space Station Processing Facility, an overhead crane lowers the S3/S4 integrated truss into the open bay of the payload canister. After it is stowed in the canister, the S3/S4 truss will be transported to the launch pad. The truss is the payload on mission STS-117, targeted for launch on March 15.

S3/S4 Integrated Truss being moved into the Space Shuttle Payloa

NASA Image and Video Library

2007-02-07

In the Space Station Processing Facility, an overhead crane lowers the S3/S4 integrated truss toward the open doors of the payload canister. After it is stowed in the canister, the S3/S4 truss will be transported to the launch pad. The truss is the payload on mission STS-117, targeted for launch on March 15.

Scalable Failure Masking for Stencil Computations using Ghost Region Expansion and Cell to Rank Remapping

DOE PAGES

Gamell, Marc; Teranishi, Keita; Kolla, Hemanth; ...

2017-10-26

In order to achieve exascale systems, application resilience needs to be addressed. Some programming models, such as task-DAG (directed acyclic graphs) architectures, currently embed resilience features whereas traditional SPMD (single program, multiple data) and message-passing models do not. Since a large part of the community's code base follows the latter models, it is still required to take advantage of application characteristics to minimize the overheads of fault tolerance. To that end, this paper explores how recovering from hard process/node failures in a local manner is a natural approach for certain applications to obtain resilience at lower costs in faulty environments.more » In particular, this paper targets enabling online, semitransparent local recovery for stencil computations on current leadership-class systems as well as presents programming support and scalable runtime mechanisms. Also described and demonstrated in this paper is the effect of failure masking, which allows the effective reduction of impact on total time to solution due to multiple failures. Furthermore, we discuss, implement, and evaluate ghost region expansion and cell-to-rank remapping to increase the probability of failure masking. To conclude, this paper shows the integration of all aforementioned mechanisms with the S3D combustion simulation through an experimental demonstration (using the Titan system) of the ability to tolerate high failure rates (i.e., node failures every five seconds) with low overhead while sustaining performance at large scales. In addition, this demonstration also displays the failure masking probability increase resulting from the combination of both ghost region expansion and cell-to-rank remapping.« less

Scalable Failure Masking for Stencil Computations using Ghost Region Expansion and Cell to Rank Remapping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamell, Marc; Teranishi, Keita; Kolla, Hemanth

In order to achieve exascale systems, application resilience needs to be addressed. Some programming models, such as task-DAG (directed acyclic graphs) architectures, currently embed resilience features whereas traditional SPMD (single program, multiple data) and message-passing models do not. Since a large part of the community's code base follows the latter models, it is still required to take advantage of application characteristics to minimize the overheads of fault tolerance. To that end, this paper explores how recovering from hard process/node failures in a local manner is a natural approach for certain applications to obtain resilience at lower costs in faulty environments.more » In particular, this paper targets enabling online, semitransparent local recovery for stencil computations on current leadership-class systems as well as presents programming support and scalable runtime mechanisms. Also described and demonstrated in this paper is the effect of failure masking, which allows the effective reduction of impact on total time to solution due to multiple failures. Furthermore, we discuss, implement, and evaluate ghost region expansion and cell-to-rank remapping to increase the probability of failure masking. To conclude, this paper shows the integration of all aforementioned mechanisms with the S3D combustion simulation through an experimental demonstration (using the Titan system) of the ability to tolerate high failure rates (i.e., node failures every five seconds) with low overhead while sustaining performance at large scales. In addition, this demonstration also displays the failure masking probability increase resulting from the combination of both ghost region expansion and cell-to-rank remapping.« less

Large-area Overhead Manipulator for Access of Fields

USDA-ARS?s Scientific Manuscript database

Multi-axis, cable-driven manipulators have evolved over many years providing large area suspended platform access, programmability, relatively rigid and flexibly-positioned platform control and full six degree of freedom (DOF) manipulation of sensors and tools. We describe innovations for a new six...

Exploring a QoS Driven Scheduling Approach for Peer-to-Peer Live Streaming Systems with Network Coding

PubMed Central

Cui, Laizhong; Lu, Nan; Chen, Fu

2014-01-01

Most large-scale peer-to-peer (P2P) live streaming systems use mesh to organize peers and leverage pull scheduling to transmit packets for providing robustness in dynamic environment. The pull scheduling brings large packet delay. Network coding makes the push scheduling feasible in mesh P2P live streaming and improves the efficiency. However, it may also introduce some extra delays and coding computational overhead. To improve the packet delay, streaming quality, and coding overhead, in this paper are as follows. we propose a QoS driven push scheduling approach. The main contributions of this paper are: (i) We introduce a new network coding method to increase the content diversity and reduce the complexity of scheduling; (ii) we formulate the push scheduling as an optimization problem and transform it to a min-cost flow problem for solving it in polynomial time; (iii) we propose a push scheduling algorithm to reduce the coding overhead and do extensive experiments to validate the effectiveness of our approach. Compared with previous approaches, the simulation results demonstrate that packet delay, continuity index, and coding ratio of our system can be significantly improved, especially in dynamic environments. PMID:25114968

S3/S4 Integrated Truss being moved into the Space Shuttle Payloa

NASA Image and Video Library

2007-02-07

In the Space Station Processing Facility, workers attach an overhead crane to the S3/S4 integrated truss in order to move it to the payload canister. After it is stowed in the canister, the S3/S4 truss will be transported to the launch pad. The truss is the payload on mission STS-117, targeted for launch on March 15.

An improved input shaping design for an efficient sway control of a nonlinear 3D overhead crane with friction

NASA Astrophysics Data System (ADS)

Maghsoudi, Mohammad Javad; Mohamed, Z.; Sudin, S.; Buyamin, S.; Jaafar, H. I.; Ahmad, S. M.

2017-08-01

This paper proposes an improved input shaping scheme for an efficient sway control of a nonlinear three dimensional (3D) overhead crane with friction using the particle swarm optimization (PSO) algorithm. Using this approach, a higher payload sway reduction is obtained as the input shaper is designed based on a complete nonlinear model, as compared to the analytical-based input shaping scheme derived using a linear second order model. Zero Vibration (ZV) and Distributed Zero Vibration (DZV) shapers are designed using both analytical and PSO approaches for sway control of rail and trolley movements. To test the effectiveness of the proposed approach, MATLAB simulations and experiments on a laboratory 3D overhead crane are performed under various conditions involving different cable lengths and sway frequencies. Their performances are studied based on a maximum residual of payload sway and Integrated Absolute Error (IAE) values which indicate total payload sway of the crane. With experiments, the superiority of the proposed approach over the analytical-based is shown by 30-50% reductions of the IAE values for rail and trolley movements, for both ZV and DZV shapers. In addition, simulations results show higher sway reductions with the proposed approach. It is revealed that the proposed PSO-based input shaping design provides higher payload sway reductions of a 3D overhead crane with friction as compared to the commonly designed input shapers.

Compensatory Muscle Activation During Unstable Overhead Squat Using a Water-filled Training Tube.

PubMed

Glass, Stephen C; Albert, Robert W

2018-05-01

Glass, SC, and Albert, RW. Compensatory muscle activation during unstable overhead squat using a water-filled training tube. J Strength Cond Res 32(5): 1230-1237, 2018-The purpose of this study was to assess compensatory muscle activation of core and support muscle during an overhead squat using a water-filled training tube. Eleven experienced weightlifting (age = 20.10 ± 0.99, mass 89.17 ± 6.88 kg) men completed 3, 30-second trials of an overhead squat using an 11.4 kg tube that was partially filled with water. A central valve allowed 3 conditions of water movement: 50% open, 100% open, and a stable(S), closed valve condition. Subjects completed 8-10 repetitions within each condition. Electromyographic (EMG) electrodes were placed over the belly of the vastus lateralis, deltoid, rectus abdominus, and paraspinal muscles and recorded during concentric and eccentric (ECC) phases. Integrated EMG were computed and converted to percent maximal voluntary contraction (%MVC). Compensatory activation was assessed using the natural log of the coefficient of variation of %MVC across repetitions. A 1-way repeated-measures analysis of variance across (phase, condition) was used. Significant compensatory muscle activation was seen in the deltoid muscle during ECC (100% open = 3.60 ± 0.50 > stable LogCV = 3.06 ± 0.45). In addition, paraspinal muscle activity was also more variable during the ECC phase (50% open LogCv = 3.28 ± 0.26 > stable = 2.77 ± 0.67). We conclude that the water-filled training tube induces compensatory muscle activation in the deltoid and paraspinal muscles during the ECC phase of the overhead squat.

Use of high intensity reflective sheeting in lieu of external lighting of overhead roadway signs : [summary].

DOT National Transportation Integrated Search

2013-06-01

Integral to every road are signs that provide essential information to drivers. The design of signs is the result of careful study from every viewpoint, including sign position, size, shape, color, background, and lettering. Also well studied are veh...

n-body simulations using message passing parallel computers.

NASA Astrophysics Data System (ADS)

Grama, A. Y.; Kumar, V.; Sameh, A.

The authors present new parallel formulations of the Barnes-Hut method for n-body simulations on message passing computers. These parallel formulations partition the domain efficiently incurring minimal communication overhead. This is in contrast to existing schemes that are based on sorting a large number of keys or on the use of global data structures. The new formulations are augmented by alternate communication strategies which serve to minimize communication overhead. The impact of these communication strategies is experimentally studied. The authors report on experimental results obtained from an astrophysical simulation on an nCUBE2 parallel computer.

CCROP-Simulation model for container-grown nursery plant production.

USDA-ARS?s Scientific Manuscript database

Container Crop Resource Optimization Program (CCROP) is an integrative model which simulates the growth and water and nutrient requirements of a woody ornamental shrub grown in small (2.8–11.4 L) containers in a field environment with overhead sprinkler irrigation. The model was developed for produc...

WATERLOPP V2/64: A highly parallel machine for numerical computation

NASA Astrophysics Data System (ADS)

Ostlund, Neil S.

1985-07-01

Current technological trends suggest that the high performance scientific machines of the future are very likely to consist of a large number (greater than 1024) of processors connected and communicating with each other in some as yet undetermined manner. Such an assembly of processors should behave as a single machine in obtaining numerical solutions to scientific problems. However, the appropriate way of organizing both the hardware and software of such an assembly of processors is an unsolved and active area of research. It is particularly important to minimize the organizational overhead of interprocessor comunication, global synchronization, and contention for shared resources if the performance of a large number ( n) of processors is to be anything like the desirable n times the performance of a single processor. In many situations, adding a processor actually decreases the performance of the overall system since the extra organizational overhead is larger than the extra processing power added. The systolic loop architecture is a new multiple processor architecture which attemps at a solution to the problem of how to organize a large number of asynchronous processors into an effective computational system while minimizing the organizational overhead. This paper gives a brief overview of the basic systolic loop architecture, systolic loop algorithms for numerical computation, and a 64-processor implementation of the architecture, WATERLOOP V2/64, that is being used as a testbed for exploring the hardware, software, and algorithmic aspects of the architecture.

Smart patch integration development of compression connector structural health monitoring in overhead transmission lines

NASA Astrophysics Data System (ADS)

Wang, Hong; Wang, Jy-An J.; Ren, Fei; Chan, John

2016-04-01

Integration of smart patches into full-tension splice connectors in overhead power transmission lines was investigated. Lead zirconate titanate (PZT) -5A was used as a smart material and an aluminum beam was used as a host structure. Negative electrode termination was examined by using copper adhesive tape and direct bonding methods. Various commercial adhesives were studied for PZT integration onto the host structure. Aluminum beam specimens with integrated PZT smart patches were tested under thermal cycling at a temperature of 125°C, which is the higher-end temperature experienced by in-service aluminum conductor steel-reinforced cables. Electromechanical impedance (EMI) measurements were conducted at room temperature, and the root mean square deviation (RMSD) of the conductance signals was used to analyze the EMI data. It has been shown that the negative electrode method has an important effect on the performance of the integrated PZT. The PZT displayed more susceptibility to cracking when copper tape was used than when direct bonding was used. The reliability of PZT in direct bonding depended on the adhesives used in bonding layers. Although a hard alumina-based adhesive can lead to cracking of the PZT, a high-temperature epoxy with adequate flexibility, such as Duralco 4538D, can provide the desired performance under target thermal cycling conditions. The RMSD parameter can characterize conductance signatures effectively. It also was demonstrated that RMSD can be used to quantify the fatigue of the PZT integration system, although RMSD is used primarily as a damage index in monitoring structural health.

Performance of an Optimized Eta Model Code on the Cray T3E and a Network of PCs

NASA Technical Reports Server (NTRS)

Kouatchou, Jules; Rancic, Miodrag; Geiger, Jim

2000-01-01

In the year 2001, NASA will launch the satellite TRIANA that will be the first Earth observing mission to provide a continuous, full disk view of the sunlit Earth. As a part of the HPCC Program at NASA GSFC, we have started a project whose objectives are to develop and implement a 3D cloud data assimilation system, by combining TRIANA measurements with model simulation, and to produce accurate statistics of global cloud coverage as an important element of the Earth's climate. For simulation of the atmosphere within this project we are using the NCEP/NOAA operational Eta model. In order to compare TRIANA and the Eta model data on approximately the same grid without significant downscaling, the Eta model will be integrated at a resolution of about 15 km. The integration domain (from -70 to +70 deg in latitude and 150 deg in longitude) will cover most of the sunlit Earth disc and will continuously rotate around the globe following TRIANA. The cloud data assimilation is supposed to run and produce 3D clouds on a near real-time basis. Such a numerical setup and integration design is very ambitious and computationally demanding. Thus, though the Eta model code has been very carefully developed and its computational efficiency has been systematically polished during the years of operational implementation at NCEP, the current MPI version may still have problems with memory and efficiency for the TRIANA simulations. Within this work, we optimize a parallel version of the Eta model code on a Cray T3E and a network of PCs (theHIVE) in order to improve its overall efficiency. Our optimization procedure consists of introducing dynamically allocated arrays to reduce the size of static memory, and optimizing on a single processor by splitting loops to limit the number of streams. All the presented results are derived using an integration domain centered at the equator, with a size of 60 x 60 deg, and with horizontal resolutions of 1/2 and 1/3 deg, respectively. In accompanying charts we report the elapsed time, the speedup and the Mflops as a function of the number of processors for the non-optimized version of the code on the T3E and theHIVE. The large amount of communication required for model integration explains its poor performance on theHIVE. Our initial implementation of the dynamic memory allocation has contributed to about 12% reduction of memory but has introduced a 3% overhead in computing time. This overhead was removed by performing loop splitting in some of the high demanding subroutines. When the Eta code is fully optimized in order to meet the memory requirement for TRIANA simulations, a non-negligeable overhead may appear that may seriously affect the efficiency of the code. To alleviate this problem, we are considering implementation of a new algorithm for the horizontal advection that is computationally less expensive, and also a new approach for marching in time.

Sculpting narrowband Fano resonances inherent in the large-area mid-infrared photonic crystal microresonators for spectroscopic imaging

PubMed Central

Liu, Jui-Nung; Schulmerich, Matthew V.; Bhargava, Rohit; Cunningham, Brian T.

2014-01-01

Fourier transform infrared (FT-IR) imaging spectrometers are almost universally used to record microspectroscopic imaging data in the mid-infrared (mid-IR) spectral region. While the commercial standard, interferometry necessitates collection of large spectral regions, requires a large data handling overhead for microscopic imaging and is slow. Here we demonstrate an approach for mid-IR spectroscopic imaging at selected discrete wavelengths using narrowband resonant filtering of a broadband thermal source, enabled by high-performance guided-mode Fano resonances in one-layer, large-area mid-IR photonic crystals on a glass substrate. The microresonant devices enable discrete frequency IR (DF-IR), in which a limited number of wavelengths that are of interest are recorded using a mechanically robust instrument. This considerably simplifies instrumentation as well as overhead of data acquisition, storage and analysis for large format imaging with array detectors. To demonstrate the approach, we perform DF-IR spectral imaging of a polymer USAF resolution target and human tissue in the C−H stretching region (2600−3300 cm−1). DF-IR spectroscopy and imaging can be generalized to other IR spectral regions and can serve as an analytical tool for environmental and biomedical applications. PMID:25089433

Measurement of SIFT operating system overhead

NASA Technical Reports Server (NTRS)

Palumbo, D. L.; Butler, R. W.

1985-01-01

The overhead of the software implemented fault tolerance (SIFT) operating system was measured. Several versions of the operating system evolved. Each version represents different strategies employed to improve the measured performance. Three of these versions are analyzed. The internal data structures of the operating systems are discussed. The overhead of the SIFT operating system was found to be of two types: vote overhead and executive task overhead. Both types of overhead were found to be significant in all versions of the system. Improvements substantially reduced this overhead; even with these improvements, the operating system consumed well over 50% of the available processing time.

Does the Medium Dictate the Message? Cultivating E-Communication in an Asynchronous Environment.

ERIC Educational Resources Information Center

Kiernan, Mary; Thomas, Pete; Woodroffe, Mark

Virtual learning environments (VLEs) are often perceived by education establishments as an opportunity to widen access without traditional overheads. An integral part of most VLEs is asynchronous computer conferencing and on-line moderators must help students migrate quickly to the new virtual environment to minimize learning disruption. This…

Integrating Cache Performance Modeling and Tuning Support in Parallelization Tools

NASA Technical Reports Server (NTRS)

Waheed, Abdul; Yan, Jerry; Saini, Subhash (Technical Monitor)

1998-01-01

With the resurgence of distributed shared memory (DSM) systems based on cache-coherent Non Uniform Memory Access (ccNUMA) architectures and increasing disparity between memory and processors speeds, data locality overheads are becoming the greatest bottlenecks in the way of realizing potential high performance of these systems. While parallelization tools and compilers facilitate the users in porting their sequential applications to a DSM system, a lot of time and effort is needed to tune the memory performance of these applications to achieve reasonable speedup. In this paper, we show that integrating cache performance modeling and tuning support within a parallelization environment can alleviate this problem. The Cache Performance Modeling and Prediction Tool (CPMP), employs trace-driven simulation techniques without the overhead of generating and managing detailed address traces. CPMP predicts the cache performance impact of source code level "what-if" modifications in a program to assist a user in the tuning process. CPMP is built on top of a customized version of the Computer Aided Parallelization Tools (CAPTools) environment. Finally, we demonstrate how CPMP can be applied to tune a real Computational Fluid Dynamics (CFD) application.

Fan-out Estimation in Spin-based Quantum Computer Scale-up.

PubMed

Nguyen, Thien; Hill, Charles D; Hollenberg, Lloyd C L; James, Matthew R

2017-10-17

Solid-state spin-based qubits offer good prospects for scaling based on their long coherence times and nexus to large-scale electronic scale-up technologies. However, high-threshold quantum error correction requires a two-dimensional qubit array operating in parallel, posing significant challenges in fabrication and control. While architectures incorporating distributed quantum control meet this challenge head-on, most designs rely on individual control and readout of all qubits with high gate densities. We analysed the fan-out routing overhead of a dedicated control line architecture, basing the analysis on a generalised solid-state spin qubit platform parameterised to encompass Coulomb confined (e.g. donor based spin qubits) or electrostatically confined (e.g. quantum dot based spin qubits) implementations. The spatial scalability under this model is estimated using standard electronic routing methods and present-day fabrication constraints. Based on reasonable assumptions for qubit control and readout we estimate 10 2 -10 5 physical qubits, depending on the quantum interconnect implementation, can be integrated and fanned-out independently. Assuming relatively long control-free interconnects the scalability can be extended. Ultimately, the universal quantum computation may necessitate a much higher number of integrated qubits, indicating that higher dimensional electronics fabrication and/or multiplexed distributed control and readout schemes may be the preferredstrategy for large-scale implementation.

Energy-Efficient Data Collection Method for Sensor Networks by Integrating Asymmetric Communication and Wake-Up Radio

PubMed Central

Iwata, Masanari; Tang, Suhua; Obana, Sadao

2018-01-01

In large-scale wireless sensor networks (WSNs), nodes close to sink nodes consume energy more quickly than other nodes due to packet forwarding. A mobile sink is a good solution to this issue, although it causes two new problems to nodes: (i) overhead of updating routing information; and (ii) increased operating time due to aperiodic query. To solve these problems, this paper proposes an energy-efficient data collection method, Sink-based Centralized transmission Scheduling (SC-Sched), by integrating asymmetric communication and wake-up radio. Specifically, each node is equipped with a low-power wake-up receiver. The sink node determines transmission scheduling, and transmits a wake-up message using a large transmission power, directly activating a pair of nodes simultaneously which will communicate with a normal transmission power. This paper further investigates how to deal with frame loss caused by fading and how to mitigate the impact of the wake-up latency of communication modules. Simulation evaluations confirm that using multiple channels effectively reduces data collection time and SC-Sched works well with a mobile sink. Compared with the conventional duty-cycling method, SC-Sched greatly reduces total energy consumption and improves the network lifetime by 7.47 times in a WSN with 4 data collection points and 300 sensor nodes. PMID:29642397

KSC-2011-2756

NASA Image and Video Library

2011-04-02

VANDENBERG AIR FORCE BASE, Calif. -- An overhead crane lifts the Aquarius/SAC-D spacecraft from its stand by an overhead to cell 3 at the Spaceport Systems International payload processing facility at Vandenberg Air Force Base in California. There, the spacecraft will undergo inspection of its solar arrays and tests will be conducted on its propulsion subsystem. Further testing of the satellites various other systems will follow. Following final tests, the spacecraft will be integrated to a United Launch Alliance Delta II rocket in preparation for the targeted June launch. Aquarius, the NASA-built primary instrument on the SAC-D spacecraft, will map global changes in salinity at the ocean's surface. The three-year mission will provide new insights into how variations in ocean surface salinity relate to these fundamental climate processes. Photo credit: NASA/Randy Beaudoin, VAFB

Lightning Protection System for Space Shuttle

NASA Technical Reports Server (NTRS)

1977-01-01

The suitability and cost effectiveness of using a lightning mast for the shuttle service and access tower (SSAT) similar to the type used for the Apollo Soyuz Test Project (ASTP) mobile launcher (ML) was evaluated. Topics covered include: (1) ASTP launch damage to mast, mast supports, grounded overhead wires, and the instrumentation system; (2) modifications required to permit reusing the ASTP mast on the SSAT; (3) comparative costing factors per launch over a 10 year period in repetitive maintenance and refurbishment of the existing and modified masts, mast supports, grounded overhead wires, and ground instrumentation required to sustain mechanical and electrical integrity of the masts; (4) effects of blast testing samples of the ASTP ML type mast (corrosion and electrical flashover); (5) comparison of damages from ASTP launch and from blast testing.

F-15 ACTIVE in flight

NASA Image and Video Library

1998-04-14

The F-15 ACTIVE in flight above the Mojave desert on April 14, 1998. The overhead shot shows the aircraft's striking red and while paint scheme/ The large forward canards are actually the tail surfaces from an F-18.

Analyse dynamique des lignes de grande portee sous charges de vent

NASA Astrophysics Data System (ADS)

Ashby, Mathieu

There are two types of electric crossing : i) subterranean / submarine line ii) overhead-line crossing. We always consider the last one as a more economic option. The inconvenience of an overhead-line crossing would be the environmental constraints among which the existing obstacles, the clearance for the navigation and the aesthetics demanded by the public. The overhead-line crossings usually have conductors of long ranges which are outside of the field of application for the current transmission line codes. These are limited to reaches of a length included between 200 m and 800 m, as well as a height of support lower than 60 m. However, for reaches over 800 m and over a height over 60 m, the criteria of conception in the transmission line codes for the calculation of wind loads are not applicable. In this study we concentrate on loads on the supports owed to the limit wind applied to bare conductors and insulators chains The objective of the present study is to examine the effect of the temporal and spatial correlation of the wind load along the conductors on a finite element model. A special attention was brought to the evaluation of the importance of the dynamic load transmitted on by the conductors and the insulators chains for the case of a turbulent wind load. The numerical study on finite element model for the example of a overhead-line crossing was done with the software ADINA. The wind load for the finite element model for the example of a overhead-line crossing was generated by the software WindGen which uses the method of Simiu-Scanlan and the method of spectral representation developed by Shinozuka-Deodatis. Wind loads generated where integrated into the finite element model ADINA for a dynamic analysis of the overhead-line crossing. For the first part, the current methods are used to calculate the efforts in supports due to the wind loads with an engineering approach and a comparaison approach. The current methods are then compared with the efforts obtained from an advanced method, transient dynamic and spectral stochastic, and specifically for the case of a simple overhead-line and an overhead-line crossings. For the second part, the effect of the longitudinal correlation of the wind load on two parallel conductors was examined. Finally, dynamic experiments on an insulators chain were made to determine the variation of the damping and the rigidity of the system for different type of insulators, different speed of application of the load and the inclination of the insulator. Key words : transient dynamics, spectral stochastic, turbulent wind, conductor, aerodynamic damping, structural damping, spatial correlation, wind spectra

Complex Conjugated certificateless-based signcryption with differential integrated factor for secured message communication in mobile network

PubMed Central

Rajagopalan, S. P.

2017-01-01

Certificateless-based signcryption overcomes inherent shortcomings in traditional Public Key Infrastructure (PKI) and Key Escrow problem. It imparts efficient methods to design PKIs with public verifiability and cipher text authenticity with minimum dependency. As a classic primitive in public key cryptography, signcryption performs validity of cipher text without decryption by combining authentication, confidentiality, public verifiability and cipher text authenticity much more efficiently than the traditional approach. In this paper, we first define a security model for certificateless-based signcryption called, Complex Conjugate Differential Integrated Factor (CC-DIF) scheme by introducing complex conjugates through introduction of the security parameter and improving secured message distribution rate. However, both partial private key and secret value changes with respect to time. To overcome this weakness, a new certificateless-based signcryption scheme is proposed by setting the private key through Differential (Diff) Equation using an Integration Factor (DiffEIF), minimizing computational cost and communication overhead. The scheme is therefore said to be proven secure (i.e. improving the secured message distributing rate) against certificateless access control and signcryption-based scheme. In addition, compared with the three other existing schemes, the CC-DIF scheme has the least computational cost and communication overhead for secured message communication in mobile network. PMID:29040290

Complex Conjugated certificateless-based signcryption with differential integrated factor for secured message communication in mobile network.

PubMed

Alagarsamy, Sumithra; Rajagopalan, S P

2017-01-01

Certificateless-based signcryption overcomes inherent shortcomings in traditional Public Key Infrastructure (PKI) and Key Escrow problem. It imparts efficient methods to design PKIs with public verifiability and cipher text authenticity with minimum dependency. As a classic primitive in public key cryptography, signcryption performs validity of cipher text without decryption by combining authentication, confidentiality, public verifiability and cipher text authenticity much more efficiently than the traditional approach. In this paper, we first define a security model for certificateless-based signcryption called, Complex Conjugate Differential Integrated Factor (CC-DIF) scheme by introducing complex conjugates through introduction of the security parameter and improving secured message distribution rate. However, both partial private key and secret value changes with respect to time. To overcome this weakness, a new certificateless-based signcryption scheme is proposed by setting the private key through Differential (Diff) Equation using an Integration Factor (DiffEIF), minimizing computational cost and communication overhead. The scheme is therefore said to be proven secure (i.e. improving the secured message distributing rate) against certificateless access control and signcryption-based scheme. In addition, compared with the three other existing schemes, the CC-DIF scheme has the least computational cost and communication overhead for secured message communication in mobile network.

Control and Non-Payload Communications (CNPC) Prototype Radio - Generation 2 Security Architecture Lab Test Report

NASA Technical Reports Server (NTRS)

Iannicca, Dennis C.; McKim, James H.; Stewart, David H.; Thadhani, Suresh K.; Young, Daniel P.

2015-01-01

NASA Glenn Research Center, in cooperation with Rockwell Collins, is working to develop a prototype Control and Non-Payload Communications (CNPC) radio platform as part of NASA Integrated Systems Research Program's (ISRP) Unmanned Aircraft Systems (UAS) Integration in the National Airspace System (NAS) project. A primary focus of the project is to work with the FAA and industry standards bodies to build and demonstrate a safe, secure, and efficient CNPC architecture that can be used by industry to evaluate the feasibility of deploying a system using these technologies in an operational capacity. GRC has been working in conjunction with these groups to assess threats, identify security requirements, and to develop a system of standards-based security controls that can be applied to the current GRC prototype CNPC architecture as a demonstration platform. The security controls were integrated into a lab test bed mock-up of the Mobile IPv6 architecture currently being used for NASA flight testing, and a series of network tests were conducted to evaluate the security overhead of the controls compared to the baseline CNPC link without any security. The aim of testing was to evaluate the performance impact of the additional security control overhead when added to the Mobile IPv6 architecture in various modes of operation. The statistics collected included packet captures at points along the path to gauge packet size as the sample data traversed the CNPC network, round trip latency, jitter, and throughput. The effort involved a series of tests of the baseline link, a link with Robust Header Compression (ROHC) and without security controls, a link with security controls and without ROHC, and finally a link with both ROHC and security controls enabled. The effort demonstrated that ROHC is both desirable and necessary to offset the additional expected overhead of applying security controls to the CNPC link.

JiTTree: A Just-in-Time Compiled Sparse GPU Volume Data Structure.

PubMed

Labschütz, Matthias; Bruckner, Stefan; Gröller, M Eduard; Hadwiger, Markus; Rautek, Peter

2016-01-01

Sparse volume data structures enable the efficient representation of large but sparse volumes in GPU memory for computation and visualization. However, the choice of a specific data structure for a given data set depends on several factors, such as the memory budget, the sparsity of the data, and data access patterns. In general, there is no single optimal sparse data structure, but a set of several candidates with individual strengths and drawbacks. One solution to this problem are hybrid data structures which locally adapt themselves to the sparsity. However, they typically suffer from increased traversal overhead which limits their utility in many applications. This paper presents JiTTree, a novel sparse hybrid volume data structure that uses just-in-time compilation to overcome these problems. By combining multiple sparse data structures and reducing traversal overhead we leverage their individual advantages. We demonstrate that hybrid data structures adapt well to a large range of data sets. They are especially superior to other sparse data structures for data sets that locally vary in sparsity. Possible optimization criteria are memory, performance and a combination thereof. Through just-in-time (JIT) compilation, JiTTree reduces the traversal overhead of the resulting optimal data structure. As a result, our hybrid volume data structure enables efficient computations on the GPU, while being superior in terms of memory usage when compared to non-hybrid data structures.

Cluster Based Location-Aided Routing Protocol for Large Scale Mobile Ad Hoc Networks

NASA Astrophysics Data System (ADS)

Wang, Yi; Dong, Liang; Liang, Taotao; Yang, Xinyu; Zhang, Deyun

Routing algorithms with low overhead, stable link and independence of the total number of nodes in the network are essential for the design and operation of the large-scale wireless mobile ad hoc networks (MANET). In this paper, we develop and analyze the Cluster Based Location-Aided Routing Protocol for MANET (C-LAR), a scalable and effective routing algorithm for MANET. C-LAR runs on top of an adaptive cluster cover of the MANET, which can be created and maintained using, for instance, the weight-based distributed algorithm. This algorithm takes into consideration the node degree, mobility, relative distance, battery power and link stability of mobile nodes. The hierarchical structure stabilizes the end-to-end communication paths and improves the networks' scalability such that the routing overhead does not become tremendous in large scale MANET. The clusterheads form a connected virtual backbone in the network, determine the network's topology and stability, and provide an efficient approach to minimizing the flooding traffic during route discovery and speeding up this process as well. Furthermore, it is fascinating and important to investigate how to control the total number of nodes participating in a routing establishment process so as to improve the network layer performance of MANET. C-LAR is to use geographical location information provided by Global Position System to assist routing. The location information of destination node is used to predict a smaller rectangle, isosceles triangle, or circle request zone, which is selected according to the relative location of the source and the destination, that covers the estimated region in which the destination may be located. Thus, instead of searching the route in the entire network blindly, C-LAR confines the route searching space into a much smaller estimated range. Simulation results have shown that C-LAR outperforms other protocols significantly in route set up time, routing overhead, mean delay and packet collision, and simultaneously maintains low average end-to-end delay, high success delivery ratio, low control overhead, as well as low route discovery frequency.

STS-32 MS Dunbar trains in JSC Manipulator Development Facility (MDF)

NASA Technical Reports Server (NTRS)

1989-01-01

STS-32 Mission Specialist (MS) Bonnie J. Dunbar reviews checklist with training personnel in the Manipulator Development Facility (MDF) in JSC's Mockup and Integration Facility (MAIL) Bldg 9A. Dunbar (left) discusses procedures with trainer in front of the aft flight deck onorbit station controls. Overhead window W8 is visible above their heads.

Integrating Technology in Today's Undergraduate Classrooms: A Look at Students' Perspectives

ERIC Educational Resources Information Center

Meehan, Kimberly C.; Salmun, Haydee

2016-01-01

The authors present the findings of a small-scale study of student opinions drawn from an anonymous and voluntary survey in an undergraduate science classroom. The survey questions focused on the use of basic tools in a college classroom. The tools included in the survey were PowerPoint, overhead projectors/chalkboards, personal response units,…

Context Switching with Multiple Register Windows: A RISC Performance Study

NASA Technical Reports Server (NTRS)

Konsek, Marion B.; Reed, Daniel A.; Watcharawittayakul, Wittaya

1987-01-01

Although previous studies have shown that a large file of overlapping register windows can greatly reduce procedure call/return overhead, the effects of register windows in a multiprogramming environment are poorly understood. This paper investigates the performance of multiprogrammed, reduced instruction set computers (RISCs) as a function of window management strategy. Using an analytic model that reflects context switch and procedure call overheads, we analyze the performance of simple, linearly self-recursive programs. For more complex programs, we present the results of a simulation study. These studies show that a simple strategy that saves all windows prior to a context switch, but restores only a single window following a context switch, performs near optimally.

Scalable Domain Decomposed Monte Carlo Particle Transport

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Brien, Matthew Joseph

2013-12-05

In this dissertation, we present the parallel algorithms necessary to run domain decomposed Monte Carlo particle transport on large numbers of processors (millions of processors). Previous algorithms were not scalable, and the parallel overhead became more computationally costly than the numerical simulation.

An innovative computer design for modeling forest landscape change in very large spatial extents with fine resolutions

Treesearch

Jian Yang; Hong S. He; Stephen R. Shifley; Frank R. Thompson; Yangjian Zhang

2011-01-01

Although forest landscape models (FLMs) have benefited greatly from ongoing advances of computer technology and software engineering, computing capacity remains a bottleneck in the design and development of FLMs. Computer memory overhead and run time efficiency are primary limiting factors when applying forest landscape models to simulate large landscapes with fine...

On the Suitability of Mobile Cloud Computing at the Tactical Edge

DTIC Science & Technology

2014-04-23

geolocation; Facial recognition (photo identification/classification); Intelligence, Surveillance, and Reconnaissance (ISR); and Fusion of Electronic...could benefit most from MCC are those with large processing overhead, low bandwidth requirements, and a need for large database support (e.g., facial ... recognition , language translation). The effect—specifically on the communication links—of supporting these applications at the tactical edge

Smartphone Response System Using Twitter to Enable Effective Interaction and Improve Engagement in Large Classrooms

ERIC Educational Resources Information Center

Kim, Yeongjun; Jeong, Soonmook; Ji, Yongwoon; Lee, Sangeun; Kwon, Key Ho; Jeon, Jae Wook

2015-01-01

This paper proposes a method for seamless interaction between students and their professor using Twitter, one of the typical social network service (SNS) platforms, in large lectures. During the lecture, the professor poses surprise questions in the form of a quiz on an overhead screen at unexpected moments, and students submit their answers…

Computational Modeling to Limit the Impact Displays and Indicator Lights Have on Habitable Volume Operational Lighting Constraints

NASA Technical Reports Server (NTRS)

Clark, T. E.; Salazr, G. A; Brainard, G. C.

2016-01-01

The goal of this investigation is to determine design limitations and architectural solutions that limit the impact light from displays and indicator lamps have on the operational environment task lighting and lighting countermeasure spectrum constraints. It is concerning that this innovative architectural lighting system, could be compromised by spectrums from display systems, architectural materials, and structures that are not considered as part a full system design implementation. The introduction of many Commercial Off the Shelf (COTS) products to the spacecraft volume that contain LEDs, without consideration to the human factors and biological constraints, is another problem. Displays and indicators are a necessary part of the spacecraft and it is the goal of this research project to determine constraints and solutions that allow these systems to be integrated while minimizing how the lighting environment is modified by them. Due to the potentially broad scope of this endeavor, the project team developed constraints for the evaluation. The evaluation will be on a set of tasks that required significant exposure in the same environment while having a large chance of impacting the light spectrum the crew is expected to receive from the architectural lighting system. The team plans to use recent HRP research on "Net Habitable Volume" [1] to provide the boundary conditions for volume size. A Zemax ® lighting model was developed of a small enclosure that had high intensity overhead lighting and a standard intensity display with LED indicator arrays. The computer model demonstrated a work surface illuminated at a high level by the overhead light source compared to displays and indicators whose light is parallel to the work plane. The overhead lighting oversaturated spectral contributions from the display and indicator at the task work surface. Interestingly, when the observer looked at the displays and LEDs within the small enclosure, their spectral contribution was significant but could be reduced by reflecting overhead light from the wall(s) to the observer. Direct observation of displays and LEDs are an issue because the user's viewing area is a display, not an illuminated work surface. Since avionics command centers consume significant crew time, the tasks that seemed at higher risk for unwanted spectral contributions as an operational volume with significant quantity of displays and indicators that were either under direct observation of the crew or impacting a volume the crew may be required to sleep in.

A low-cost transportable ground station for capture and processing of direct broadcast EOS satellite data

NASA Technical Reports Server (NTRS)

Davis, Don; Bennett, Toby; Short, Nicholas M., Jr.

1994-01-01

The Earth Observing System (EOS), part of a cohesive national effort to study global change, will deploy a constellation of remote sensing spacecraft over a 15 year period. Science data from the EOS spacecraft will be processed and made available to a large community of earth scientists via NASA institutional facilities. A number of these spacecraft are also providing an additional interface to broadcast data directly to users. Direct broadcast of real-time science data from overhead spacecraft has valuable applications including validation of field measurements, planning science campaigns, and science and engineering education. The success and usefulness of EOS direct broadcast depends largely on the end-user cost of receiving the data. To extend this capability to the largest possible user base, the cost of receiving ground stations must be as low as possible. To achieve this goal, NASA Goddard Space Flight Center is developing a prototype low-cost transportable ground station for EOS direct broadcast data based on Very Large Scale Integration (VLSI) components and pipelined, multiprocessing architectures. The targeted reproduction cost of this system is less than $200K. This paper describes a prototype ground station and its constituent components.

Developing a Crew Time Model for Human Exploration Missions to Mars

NASA Technical Reports Server (NTRS)

Battfeld, Bryan; Stromgren, Chel; Shyface, Hilary; Cirillo, William; Goodliff, Kandyce

2015-01-01

Candidate human missions to Mars require mission lengths that could extend beyond those that have previously been demonstrated during crewed Lunar (Apollo) and International Space Station (ISS) missions. The nature of the architectures required for deep space human exploration will likely necessitate major changes in how crews operate and maintain the spacecraft. The uncertainties associated with these shifts in mission constructs - including changes to habitation systems, transit durations, and system operations - raise concerns as to the ability of the crew to complete required overhead activities while still having time to conduct a set of robust exploration activities. This paper will present an initial assessment of crew operational requirements for human missions to the Mars surface. The presented results integrate assessments of crew habitation, system maintenance, and utilization to present a comprehensive analysis of potential crew time usage. Destination operations were assessed for a short (approx. 50 day) and long duration (approx. 500 day) surface habitation case. Crew time allocations are broken out by mission segment, and the availability of utilization opportunities was evaluated throughout the entire mission progression. To support this assessment, the integrated crew operations model (ICOM) was developed. ICOM was used to parse overhead, maintenance and system repair, and destination operations requirements within each mission segment - outbound transit, Mars surface duration, and return transit - to develop a comprehensive estimation of exploration crew time allocations. Overhead operational requirements included daily crew operations, health maintenance activities, and down time. Maintenance and repair operational allocations are derived using the Exploration Maintainability and Analysis Tool (EMAT) to develop a probabilistic estimation of crew repair time necessary to maintain systems functionality throughout the mission.

Efficient Ada multitasking on a RISC register window architecture

NASA Technical Reports Server (NTRS)

Kearns, J. P.; Quammen, D.

1987-01-01

This work addresses the problem of reducing context switch overhead on a processor which supports a large register file - a register file much like that which is part of the Berkeley RISC processors and several other emerging architectures (which are not necessarily reduced instruction set machines in the purest sense). Such a reduction in overhead is particularly desirable in a real-time embedded application, in which task-to-task context switch overhead may result in failure to meet crucial deadlines. A storage management technique by which a context switch may be implemented as cheaply as a procedure call is presented. The essence of this technique is the avoidance of the save/restore of registers on the context switch. This is achieved through analysis of the static source text of an Ada tasking program. Information gained during that analysis directs the optimized storage management strategy for that program at run time. A formal verification of the technique in terms of an operational control model and an evaluation of the technique's performance via simulations driven by synthetic Ada program traces are presented.

Access-in-turn test architecture for low-power test application

NASA Astrophysics Data System (ADS)

Wang, Weizheng; Wang, JinCheng; Wang, Zengyun; Xiang, Lingyun

2017-03-01

This paper presents a novel access-in-turn test architecture (AIT-TA) for testing of very large scale integrated (VLSI) designs. In the proposed scheme, each scan cell in a chain receives test data from shift-in line in turn while pushing its test response to the shift-out line. It solves the power problem of conventional scan architecture to a great extent and suppresses significantly the switching activity during shift and capture operation with acceptable hardware overhead. Thus, it can help to implement the test at much higher operation frequencies resulting shorter test application time. The proposed test approach enhances the architecture of conventional scan flip-flops and backward compatible with existing test pattern generation and simulation techniques. Experimental results obtained for some larger ISCAS'89 and ITC'99 benchmark circuits illustrate effectiveness of the proposed low-power test application scheme.

Analysis of severe storm data

NASA Technical Reports Server (NTRS)

Hickey, J. S.

1983-01-01

The Mesoscale Analysis and Space Sensor (MASS) Data Management and Analysis System developed by Atsuko Computing International (ACI) on the MASS HP-1000 Computer System within the Systems Dynamics Laboratory of the Marshall Space Flight Center is described. The MASS Data Management and Analysis System was successfully implemented and utilized daily by atmospheric scientists to graphically display and analyze large volumes of conventional and satellite derived meteorological data. The scientists can process interactively various atmospheric data (Sounding, Single Level, Gird, and Image) by utilizing the MASS (AVE80) share common data and user inputs, thereby reducing overhead, optimizing execution time, and thus enhancing user flexibility, useability, and understandability of the total system/software capabilities. In addition ACI installed eight APPLE III graphics/imaging computer terminals in individual scientist offices and integrated them into the MASS HP-1000 Computer System thus providing significant enhancement to the overall research environment.

KSC-08pd2353

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – An overhead crane in the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center lowers the Fine Guidance Sensor, or FGS, onto the Orbital Replacement Unit Carrier or ORUC, below for installation. An FGS consists of a large structure housing a collection of mirrors, lenses, servos, prisms, beam splitters and photomultiplier tubes. There are three fine guidance sensors on Hubble located at 90-degree intervals around the circumference of the telescope. Along with the gyroscopes, the optical sensors are a key component of Hubble’s highly complex but extraordinarily effective “pointing control system.” The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125, on space shuttle Atlantis. Launch is targeted for Oct. 8. Photo credit: NASA/Jim Grossmann

PLUM: Parallel Load Balancing for Adaptive Unstructured Meshes

NASA Technical Reports Server (NTRS)

Oliker, Leonid; Biswas, Rupak; Saini, Subhash (Technical Monitor)

1998-01-01

Mesh adaption is a powerful tool for efficient unstructured-grid computations but causes load imbalance among processors on a parallel machine. We present a novel method called PLUM to dynamically balance the processor workloads with a global view. This paper presents the implementation and integration of all major components within our dynamic load balancing strategy for adaptive grid calculations. Mesh adaption, repartitioning, processor assignment, and remapping are critical components of the framework that must be accomplished rapidly and efficiently so as not to cause a significant overhead to the numerical simulation. A data redistribution model is also presented that predicts the remapping cost on the SP2. This model is required to determine whether the gain from a balanced workload distribution offsets the cost of data movement. Results presented in this paper demonstrate that PLUM is an effective dynamic load balancing strategy which remains viable on a large number of processors.

Long-ranged contributions to solvation free energies from theory and short-ranged models

PubMed Central

Remsing, Richard C.; Liu, Shule; Weeks, John D.

2016-01-01

Long-standing problems associated with long-ranged electrostatic interactions have plagued theory and simulation alike. Traditional lattice sum (Ewald-like) treatments of Coulomb interactions add significant overhead to computer simulations and can produce artifacts from spurious interactions between simulation cell images. These subtle issues become particularly apparent when estimating thermodynamic quantities, such as free energies of solvation in charged and polar systems, to which long-ranged Coulomb interactions typically make a large contribution. In this paper, we develop a framework for determining very accurate solvation free energies of systems with long-ranged interactions from models that interact with purely short-ranged potentials. Our approach is generally applicable and can be combined with existing computational and theoretical techniques for estimating solvation thermodynamics. We demonstrate the utility of our approach by examining the hydration thermodynamics of hydrophobic and ionic solutes and the solvation of a large, highly charged colloid that exhibits overcharging, a complex nonlinear electrostatic phenomenon whereby counterions from the solvent effectively overscreen and locally invert the integrated charge of the solvated object. PMID:26929375

30 CFR 57.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operator-carrying overhead cranes. 57.16014 Section 57.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 56.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Operator-carrying overhead cranes. 56.16014 Section 56.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 56.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operator-carrying overhead cranes. 56.16014 Section 56.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

30 CFR 57.16014 - Operator-carrying overhead cranes.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Operator-carrying overhead cranes. 57.16014 Section 57.16014 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16014 Operator-carrying overhead cranes. Operator-carrying overhead cranes shall...

Analyzing large scale genomic data on the cloud with Sparkhit

PubMed Central

Huang, Liren; Krüger, Jan

2018-01-01

Abstract Motivation The increasing amount of next-generation sequencing data poses a fundamental challenge on large scale genomic analytics. Existing tools use different distributed computational platforms to scale-out bioinformatics workloads. However, the scalability of these tools is not efficient. Moreover, they have heavy run time overheads when pre-processing large amounts of data. To address these limitations, we have developed Sparkhit: a distributed bioinformatics framework built on top of the Apache Spark platform. Results Sparkhit integrates a variety of analytical methods. It is implemented in the Spark extended MapReduce model. It runs 92–157 times faster than MetaSpark on metagenomic fragment recruitment and 18–32 times faster than Crossbow on data pre-processing. We analyzed 100 terabytes of data across four genomic projects in the cloud in 21 h, which includes the run times of cluster deployment and data downloading. Furthermore, our application on the entire Human Microbiome Project shotgun sequencing data was completed in 2 h, presenting an approach to easily associate large amounts of public datasets with reference data. Availability and implementation Sparkhit is freely available at: https://rhinempi.github.io/sparkhit/. Contact asczyrba@cebitec.uni-bielefeld.de Supplementary information Supplementary data are available at Bioinformatics online. PMID:29253074

Handheld tools assess medical necessity at the point of care.

PubMed

Pollard, Dan

2002-01-01

An emerging strategy to manage financial risk in clinical practice is to involve the physician at the point of care. Using handheld technology, encounter-specific information along with medical necessity policy can be presented to physicians allowing them to integrate it into their medical decision-making process. Three different strategies are discussed: reference books or paper encounter forms, electronic reference tools, and integrated process tools. The electronic reference tool strategy was evaluated and showed a return on investment exceeding 1200% due to reduced overhead costs associated with rework of claim errors.

Integrated Verification Experiment data collected as part of the Los Alamos National Laboratory's Source Region Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitzgerald, T.J.; Carlos, R.C.; Argo, P.E.

As part of the integrated verification experiment (IVE), we deployed a network of hf ionospheric sounders to detect the effects of acoustic waves generated by surface ground motion following underground nuclear tests at the Nevada Test Site. The network sampled up to four geographic locations in the ionosphere from almost directly overhead of the surface ground zero out to a horizontal range of 60 km. We present sample results for four of the IVEs: Misty Echo, Texarkana, Mineral Quarry, and Bexar.

29 CFR 1926.1438 - Overhead & gantry cranes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Overhead & gantry cranes. 1926.1438 Section 1926.1438 Labor... (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Cranes and Derricks in Construction § 1926.1438 Overhead & gantry cranes. (a) Permanently installed overhead and gantry cranes. The requirements of § 1910...

What Does It Cost? An Essay on Overheads.

ERIC Educational Resources Information Center

Abrahamson, Brian

1989-01-01

Issues in determination of overhead for cost recovery from research funding sources are discussed, including the need to collect overhead, principles involved in charging for overhead, range of activity types to be considered, classification and calculation of costs, pricing policy, and payment to the university versus payment to its components.…

School District Size and the Deployment of Personnel Resources.

ERIC Educational Resources Information Center

Daft, Richard L.; Becker, Selwyn W.

1978-01-01

The administrative component was found to receive a smaller proportion of salaries in large districts, while clerical and maintenance service proportions increased, producing a net effect of larger overhead costs in this study of high school districts in the midwestern U.S. (KR)

The cost of conservative synchronization in parallel discrete event simulations

NASA Technical Reports Server (NTRS)

Nicol, David M.

1990-01-01

The performance of a synchronous conservative parallel discrete-event simulation protocol is analyzed. The class of simulation models considered is oriented around a physical domain and possesses a limited ability to predict future behavior. A stochastic model is used to show that as the volume of simulation activity in the model increases relative to a fixed architecture, the complexity of the average per-event overhead due to synchronization, event list manipulation, lookahead calculations, and processor idle time approach the complexity of the average per-event overhead of a serial simulation. The method is therefore within a constant factor of optimal. The analysis demonstrates that on large problems--those for which parallel processing is ideally suited--there is often enough parallel workload so that processors are not usually idle. The viability of the method is also demonstrated empirically, showing how good performance is achieved on large problems using a thirty-two node Intel iPSC/2 distributed memory multiprocessor.

Significant clinical practice cost savings through downsizing office supply inventory and just in time ordering.

PubMed

Gonzalez, Chris M; Jang, Tom; Raines, Melanie; Lys, Thomas Z; Schaeffer, Anthony J

2006-07-01

Cost containment in the office is becoming more important secondary to increasing overhead costs and lower reimbursement. In an attempt to limit these particular expenditures we analyzed and restructured our methods of ordering, storing and distributing office supply inventory. In a large academic practice with 11 urologists and approximately 20,000 annual patient visits an attempt was made to decrease overhead costs using the principle of just in time inventory popularized by large manufacturing companies. We initially issued a return of excess and/or unused supplies from our office inventory stock room. Our main supply room was then centralized to contain office supplies for up to 4 weeks. The 12 individual clinic rooms were stocked with appropriate supplies to last 1 week. Limited access to the main supply room was established and a supply manager was established to log all input and output. The initial credit for the return of unused/overstocked supplies was $10,107 in January 2004. Annual office supply charges in calendar year 2004 were $87,444 compared to charges in calendar year 2003 of $175,340. No stock outs occurred during year 2004 and all standing delivery orders were terminated. The total number of patient visits in calendar year 2004 was 20,170 compared to 19,455 in calendar year 2003. Decreasing overall inventory through accurate demand forecasting, judicious accounting, office supply centralization and just in time ordering is a potential area for significant overhead cost savings in a clinical practice.

Interactions between riparian shading and food supply: a seasonal comparison of effects on time budgets, space use and growth in Atlantic salmon Salmo salar.

PubMed

Orpwood, J E; Armstrong, J D; Griffiths, S W

2010-11-01

This study examines seasonal (winter v. summer) differences in space-time budgets, food intake and growth of Atlantic salmon Salmo salar parr in a controlled, large-scale stream environment, to examine the direction and magnitude of shifts in behaviour patterns as influenced by the availability of overhead cover and food supply. Salmo salar parr tested in the presence of overhead cover were significantly more nocturnal and occupied more peripheral positions than those tested in the absence of overhead cover. This increase in nocturnal activity was driven primarily by increased activity at night, accompanied by a reduction in daytime activity during winter. The presence of overhead cover had no effect on rates of food intake or growth for a given food supply in a given season. Growth rates were significantly higher for fish subjected to a high food supply than those subjected to a low food supply. Food supply did not affect the extent to which S. salar parr were nocturnal. These results were consistent between winter and summer. The use of riparian shading as a management technique to mitigate the effects of warming allows the adoption of more risk-averse foraging behaviour and may be particularly beneficial in circumstances where it serves also to increase the availability of food. © 2010 Crown Copyright Marine Scotland. Journal of Fish Biology © 2010 The Fisheries Society of the British Isles.

Integrated coke, asphalt and jet fuel production process and apparatus

DOEpatents

Shang, Jer Y.

1991-01-01

A process and apparatus for the production of coke, asphalt and jet fuel m a feed of fossil fuels containing volatile carbon compounds therein is disclosed. The process includes the steps of pyrolyzing the feed in an entrained bed pyrolyzing means, separating the volatile pyrolysis products from the solid pyrolysis products removing at least one coke from the solid pyrolysis products, fractionating the volatile pyrolysis products to produce an overhead stream and a bottom stream which is useful as asphalt for road pavement, condensing the overhead stream to produce a condensed liquid fraction and a noncondensable, gaseous fraction, and removing water from the condensed liquid fraction to produce a jet fuel-containing product. The disclosed apparatus is useful for practicing the foregoing process. the process provides a useful method of mass producing and jet fuels from materials such as coal, oil shale and tar sands.

DDS as middleware of the Southern African Large Telescope control system

NASA Astrophysics Data System (ADS)

Maartens, Deneys S.; Brink, Janus D.

2016-07-01

The Southern African Large Telescope (SALT) software control system1 is realised as a distributed control system, implemented predominantly in National Instruments' LabVIEW. The telescope control subsystems communicate using cyclic, state-based messages. Currently, transmitting a message is accomplished by performing an HTTP PUT request to a WebDAV directory on a centralised Apache web server, while receiving is based on polling the web server for new messages. While the method works, it presents a number of drawbacks; a scalable distributed communication solution with minimal overhead is a better fit for control systems. This paper describes our exploration of the Data Distribution Service (DDS). DDS is a formal standard specification, defined by the Object Management Group (OMG), that presents a data-centric publish-subscribe model for distributed application communication and integration. It provides an infrastructure for platform- independent many-to-many communication. A number of vendors provide implementations of the DDS standard; RTI, in particular, provides a DDS toolkit for LabVIEW. This toolkit has been evaluated against the needs of SALT, and a few deficiencies have been identified. We have developed our own implementation that interfaces LabVIEW to DDS in order to address our specific needs. Our LabVIEW DDS interface implementation is built against the RTI DDS Core component, provided by RTI under their Open Community Source licence. Our needs dictate that the interface implementation be platform independent. Since we have access to the RTI DDS Core source code, we are able to build the RTI DDS libraries for any of the platforms on which we require support. The communications functionality is based on UDP multicasting. Multicasting is an efficient communications mechanism with low overheads which avoids duplicated point-to-point transmission of data on a network where there are multiple recipients of the data. In the paper we present a performance evaluation of DDS against the current HTTP-based implementation as well as the historical DataSocket implementation. We conclude with a summary and describe future work.

118. VIEW, LOOKING SOUTHWEST OF GOLD AMALGAMATION ROOM, SHOWING AMALGAMATION ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

118. VIEW, LOOKING SOUTHWEST OF GOLD AMALGAMATION ROOM, SHOWING AMALGAMATION BARREL AT CENTER FOREGROUND, BULLION FURNACE IN LARGE HOOD BEHIND IT, AND GOLD RETORT IN BACKGROUND HOOD. NOTE OVERHEAD MONORAIL FOR MATERIALS HANDLING. - Shenandoah-Dives Mill, 135 County Road 2, Silverton, San Juan County, CO

30 CFR 57.16015 - Work or travel on overhead crane bridges.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Work or travel on overhead crane bridges. 57... MINES Materials Storage and Handling § 57.16015 Work or travel on overhead crane bridges. No person shall work from or travel on the bridge of an overhead crane unless the bridge is provided with...

30 CFR 56.16015 - Work or travel on overhead crane bridges.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Work or travel on overhead crane bridges. 56... Materials Storage and Handling § 56.16015 Work or travel on overhead crane bridges. No person shall work from or travel on the bridge of an overhead crane unless the bridge is provided with substantial...

Effective Determination of Overhead Rates for Pricing Goods and Services.

ERIC Educational Resources Information Center

Smith, Christopher A.

This publication presents a system of gathering overhead data and describes several methods for assigning overhead costs to specific contract prices. It is intended to provide facility production supervisors with a means of ensuring adequate cost recovery in bid prices and gaining a measure of overhead cost control. The seven steps in the overhead…

30 CFR 57.16015 - Work or travel on overhead crane bridges.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Work or travel on overhead crane bridges. 57... MINES Materials Storage and Handling § 57.16015 Work or travel on overhead crane bridges. No person shall work from or travel on the bridge of an overhead crane unless the bridge is provided with...

30 CFR 56.16015 - Work or travel on overhead crane bridges.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Work or travel on overhead crane bridges. 56... Materials Storage and Handling § 56.16015 Work or travel on overhead crane bridges. No person shall work from or travel on the bridge of an overhead crane unless the bridge is provided with substantial...

Optical Communications With A Geiger Mode APD Array

DTIC Science & Technology

2016-02-09

spurious fires from numerous sources, including crosstalk from other detectors in the same array . Additionally, after a 9 successful detection, the...be combined into arrays with large numbers of detectors , allowing for scaling of dynamic range with relatively little overhead on space and power...overall higher rate of dark counts than a single detector , this is more than compensated for by the extra detectors . A sufficiently large APD array could

Integrated Optoelectronic Networks for Application-Driven Multicore Computing

DTIC Science & Technology

2017-05-08

hybrid photonic torus, the all-optical Corona crossbar, and the hybrid hierarchical Firefly crossbar. • The key challenges for waveguide photonics...improves SXR but with relatively higher EDP overhead. Our evaluation results indicate that the encoding schemes improve worst-case-SXR in Corona and...photonic crossbar architectures ( Corona and Firefly) indicate that our approach improves worst-case signal-to-noise ratio (SNR) by up to 51.7

A Job Pause Service under LAM/MPI+BLCR for Transparent Fault Tolerance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Chao; Mueller, Frank; Engelmann, Christian

2007-01-01

Checkpoint/restart (C/R) has become a requirement for long-running jobs in large-scale clusters due to a meantime- to-failure (MTTF) in the order of hours. After a failure, C/R mechanisms generally require a complete restart of an MPI job from the last checkpoint. A complete restart, however, is unnecessary since all but one node are typically still alive. Furthermore, a restart may result in lengthy job requeuing even though the original job had not exceeded its time quantum. In this paper, we overcome these shortcomings. Instead of job restart, we have developed a transparent mechanism for job pause within LAM/MPI+BLCR. This mechanismmore » allows live nodes to remain active and roll back to the last checkpoint while failed nodes are dynamically replaced by spares before resuming from the last checkpoint. Our methodology includes LAM/MPI enhancements in support of scalable group communicationwith fluctuating number of nodes, reuse of network connections, transparent coordinated checkpoint scheduling and a BLCR enhancement for job pause. Experiments in a cluster with the NAS Parallel Benchmark suite show that our overhead for job pause is comparable to that of a complete job restart. A minimal overhead of 5.6% is only incurred in case migration takes place while the regular checkpoint overhead remains unchanged. Yet, our approach alleviates the need to reboot the LAM run-time environment, which accounts for considerable overhead resulting in net savings of our scheme in the experiments. Our solution further provides full transparency and automation with the additional benefit of reusing existing resources. Executing continues after failures within the scheduled job, i.e., the application staging overhead is not incurred again in contrast to a restart. Our scheme offers additional potential for savings through incremental checkpointing and proactive diskless live migration, which we are currently working on.« less

Quantum error correction in crossbar architectures

NASA Astrophysics Data System (ADS)

Helsen, Jonas; Steudtner, Mark; Veldhorst, Menno; Wehner, Stephanie

2018-07-01

A central challenge for the scaling of quantum computing systems is the need to control all qubits in the system without a large overhead. A solution for this problem in classical computing comes in the form of so-called crossbar architectures. Recently we made a proposal for a large-scale quantum processor (Li et al arXiv:1711.03807 (2017)) to be implemented in silicon quantum dots. This system features a crossbar control architecture which limits parallel single-qubit control, but allows the scheme to overcome control scaling issues that form a major hurdle to large-scale quantum computing systems. In this work, we develop a language that makes it possible to easily map quantum circuits to crossbar systems, taking into account their architecture and control limitations. Using this language we show how to map well known quantum error correction codes such as the planar surface and color codes in this limited control setting with only a small overhead in time. We analyze the logical error behavior of this surface code mapping for estimated experimental parameters of the crossbar system and conclude that logical error suppression to a level useful for real quantum computation is feasible.

78 FR 68477 - Overhead and Gantry Cranes; Extension of the Office of Management and Budget's (OMB) Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-14

...] Overhead and Gantry Cranes; Extension of the Office of Management and Budget's (OMB) Approval of... requirements specified in the Standard on Overhead and Gantry Cranes (29 CFR 1910.179). DATES: Comments must be... information (29 U.S.C. 657). The paperwork provisions of the Standard on Overhead and Gantry Cranes specify...

Behavioral economics. Avoiding overhead aversion in charity.

PubMed

Gneezy, Uri; Keenan, Elizabeth A; Gneezy, Ayelet

2014-10-31

Donors tend to avoid charities that dedicate a high percentage of expenses to administrative and fundraising costs, limiting the ability of nonprofits to be effective. We propose a solution to this problem: Use donations from major philanthropists to cover overhead expenses and offer potential donors an overhead-free donation opportunity. A laboratory experiment testing this solution confirms that donations decrease when overhead increases, but only when donors pay for overhead themselves. In a field experiment with 40,000 potential donors, we compared the overhead-free solution with other common uses of initial donations. Consistent with prior research, informing donors that seed money has already been raised increases donations, as does a $1:$1 matching campaign. Our main result, however, clearly shows that informing potential donors that overhead costs are covered by an initial donation significantly increases the donation rate by 80% (or 94%) and total donations by 75% (or 89%) compared with the seed (or matching) approach. Copyright © 2014, American Association for the Advancement of Science.

In-House vs. Franchise College Food Services and Bookstores.

ERIC Educational Resources Information Center

Stumph, W. J.

In determining whether colleges or universities should operate their own food services or bookstores or lease them to contract operators, school business officers should consider a number of factors. These include whether sales volume is sufficiently large to cover direct operating costs and overhead; inventory investment; appearance, service, and…

Fault-Tolerant and Elastic Streaming MapReduce with Decentralized Coordination

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumbhare, Alok; Frincu, Marc; Simmhan, Yogesh

2015-06-29

The MapReduce programming model, due to its simplicity and scalability, has become an essential tool for processing large data volumes in distributed environments. Recent Stream Processing Systems (SPS) extend this model to provide low-latency analysis of high-velocity continuous data streams. However, integrating MapReduce with streaming poses challenges: first, the runtime variations in data characteristics such as data-rates and key-distribution cause resource overload, that inturn leads to fluctuations in the Quality of the Service (QoS); and second, the stateful reducers, whose state depends on the complete tuple history, necessitates efficient fault-recovery mechanisms to maintain the desired QoS in the presence ofmore » resource failures. We propose an integrated streaming MapReduce architecture leveraging the concept of consistent hashing to support runtime elasticity along with locality-aware data and state replication to provide efficient load-balancing with low-overhead fault-tolerance and parallel fault-recovery from multiple simultaneous failures. Our evaluation on a private cloud shows up to 2:8 improvement in peak throughput compared to Apache Storm SPS, and a low recovery latency of 700 -1500 ms from multiple failures.« less

75 FR 33320 - Notice of Issuance of Final Determination Concerning a Lift Unit for an Overhead Patient Lift...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-11

... Determination Concerning a Lift Unit for an Overhead Patient Lift System; Correction AGENCY: U.S. Customs and... origin of a lift unit for an overhead patient lift system. The document contained two errors that this... origin of a lift unit for an overhead patient lift system. This document corrects in the DATES section of...

Program Correctness, Verification and Testing for Exascale (Corvette)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sen, Koushik; Iancu, Costin; Demmel, James W

The goal of this project is to provide tools to assess the correctness of parallel programs written using hybrid parallelism. There is a dire lack of both theoretical and engineering know-how in the area of finding bugs in hybrid or large scale parallel programs, which our research aims to change. In the project we have demonstrated novel approaches in several areas: 1. Low overhead automated and precise detection of concurrency bugs at scale. 2. Using low overhead bug detection tools to guide speculative program transformations for performance. 3. Techniques to reduce the concurrency required to reproduce a bug using partialmore » program restart/replay. 4. Techniques to provide reproducible execution of floating point programs. 5. Techniques for tuning the floating point precision used in codes.« less

Advanced Silicon Photonic Transceivers - the Case of a Wavelength Division and Polarization Multiplexed Quadrature Phase Shift Keying Receiver for Terabit/s Optical Transmission

DTIC Science & Technology

2017-03-10

formats by the co- integration of a passive 90 degree optical hybrid, highspeed balanced Ge photodetectors and a high-speed two-channel transimpedance...40 Gbaud and can handle advanced modulation formats by the co-integration of a passive 90 degree optical hybrid, high- speed balanced Ge...reached at an OSNR of 12.4 dB. The hard -decision FEC (HD-FEC) threshold (BER of 3.8 × 10-3 for 7% overhead) requires 14 dB OSNR. For 16-QAM this requires

Integrated Verification Experiment data collected as part of the Los Alamos National Laboratory`s Source Region Program. Appendix D: Ionospheric measurements for IVEs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fitzgerald, T.J.; Carlos, R.C.; Argo, P.E.

As part of the integrated verification experiment (IVE), we deployed a network of hf ionospheric sounders to detect the effects of acoustic waves generated by surface ground motion following underground nuclear tests at the Nevada Test Site. The network sampled up to four geographic locations in the ionosphere from almost directly overhead of the surface ground zero out to a horizontal range of 60 km. We present sample results for four of the IVEs: Misty Echo, Texarkana, Mineral Quarry, and Bexar.

Computation and Communication Evaluation of an Authentication Mechanism for Time-Triggered Networked Control Systems

PubMed Central

Martins, Goncalo; Moondra, Arul; Dubey, Abhishek; Bhattacharjee, Anirban; Koutsoukos, Xenofon D.

2016-01-01

In modern networked control applications, confidentiality and integrity are important features to address in order to prevent against attacks. Moreover, network control systems are a fundamental part of the communication components of current cyber-physical systems (e.g., automotive communications). Many networked control systems employ Time-Triggered (TT) architectures that provide mechanisms enabling the exchange of precise and synchronous messages. TT systems have computation and communication constraints, and with the aim to enable secure communications in the network, it is important to evaluate the computational and communication overhead of implementing secure communication mechanisms. This paper presents a comprehensive analysis and evaluation of the effects of adding a Hash-based Message Authentication (HMAC) to TT networked control systems. The contributions of the paper include (1) the analysis and experimental validation of the communication overhead, as well as a scalability analysis that utilizes the experimental result for both wired and wireless platforms and (2) an experimental evaluation of the computational overhead of HMAC based on a kernel-level Linux implementation. An automotive application is used as an example, and the results show that it is feasible to implement a secure communication mechanism without interfering with the existing automotive controller execution times. The methods and results of the paper can be used for evaluating the performance impact of security mechanisms and, thus, for the design of secure wired and wireless TT networked control systems. PMID:27463718

Computation and Communication Evaluation of an Authentication Mechanism for Time-Triggered Networked Control Systems.

PubMed

Martins, Goncalo; Moondra, Arul; Dubey, Abhishek; Bhattacharjee, Anirban; Koutsoukos, Xenofon D

2016-07-25

In modern networked control applications, confidentiality and integrity are important features to address in order to prevent against attacks. Moreover, network control systems are a fundamental part of the communication components of current cyber-physical systems (e.g., automotive communications). Many networked control systems employ Time-Triggered (TT) architectures that provide mechanisms enabling the exchange of precise and synchronous messages. TT systems have computation and communication constraints, and with the aim to enable secure communications in the network, it is important to evaluate the computational and communication overhead of implementing secure communication mechanisms. This paper presents a comprehensive analysis and evaluation of the effects of adding a Hash-based Message Authentication (HMAC) to TT networked control systems. The contributions of the paper include (1) the analysis and experimental validation of the communication overhead, as well as a scalability analysis that utilizes the experimental result for both wired and wireless platforms and (2) an experimental evaluation of the computational overhead of HMAC based on a kernel-level Linux implementation. An automotive application is used as an example, and the results show that it is feasible to implement a secure communication mechanism without interfering with the existing automotive controller execution times. The methods and results of the paper can be used for evaluating the performance impact of security mechanisms and, thus, for the design of secure wired and wireless TT networked control systems.

Highly Efficient and Scalable Compound Decomposition of Two-Electron Integral Tensor and Its Application in Coupled Cluster Calculations.

PubMed

Peng, Bo; Kowalski, Karol

2017-09-12

The representation and storage of two-electron integral tensors are vital in large-scale applications of accurate electronic structure methods. Low-rank representation and efficient storage strategy of integral tensors can significantly reduce the numerical overhead and consequently time-to-solution of these methods. In this work, by combining pivoted incomplete Cholesky decomposition (CD) with a follow-up truncated singular vector decomposition (SVD), we develop a decomposition strategy to approximately represent the two-electron integral tensor in terms of low-rank vectors. A systematic benchmark test on a series of 1-D, 2-D, and 3-D carbon-hydrogen systems demonstrates high efficiency and scalability of the compound two-step decomposition of the two-electron integral tensor in our implementation. For the size of the atomic basis set, N b , ranging from ∼100 up to ∼2,000, the observed numerical scaling of our implementation shows [Formula: see text] versus [Formula: see text] cost of performing single CD on the two-electron integral tensor in most of the other implementations. More importantly, this decomposition strategy can significantly reduce the storage requirement of the atomic orbital (AO) two-electron integral tensor from [Formula: see text] to [Formula: see text] with moderate decomposition thresholds. The accuracy tests have been performed using ground- and excited-state formulations of coupled cluster formalism employing single and double excitations (CCSD) on several benchmark systems including the C 60 molecule described by nearly 1,400 basis functions. The results show that the decomposition thresholds can be generally set to 10 -4 to 10 -3 to give acceptable compromise between efficiency and accuracy.

Extending IPsec for Efficient Remote Attestation

NASA Astrophysics Data System (ADS)

Sadeghi, Ahmad-Reza; Schulz, Steffen

When establishing a VPN to connect different sites of a network, the integrity of the involved VPN endpoints is often a major security concern. Based on the Trusted Platform Module (TPM), available in many computing platforms today, remote attestation mechanisms can be used to evaluate the internal state of remote endpoints automatically. However, existing protocols and extensions are either unsuited for use with IPsec or impose considerable additional implementation complexity and protocol overhead.

Report on Analyses of WAC Samples of Evaporator Overheads - 2004

DOE Office of Scientific and Technical Information (OSTI.GOV)

OJI, LAWRENCE

2004-08-16

All water received into ETF requires characterization versus the defined Waste Acceptance Criteria. Currently much of the water received by ETF comes from the F and H Evaporator Overheads. Concentration, Storage and Transfer Engineering issued a modified list of species to be determined. In March of 2004, the Tank Farm submitted annual samples from 2F, 2H and 3H Evaporator Overhead streams for characterization to verify compliance with the Effluent Treatment Facility (ETF) Waste Acceptance Criteria (WAC) and to look for organic species. With the exception of high silicon in the 2H and slightly high tritium in 2F evaporator overheads, allmore » the overheads samples were found to be in compliance with the Effluent Treatment Facility WAC. The silicon concentration in the 2H-evaporator overhead, at 44 mg/L, was above the ETF WAC limit of 5 mg/L and tritium at 2.11E+05 dpm/mL in 2F overhead sample was above the ETF WAC limit of 1.2E+05 dpm/mL.« less

A Simple, Low Overhead Data Compression Algorithm for Converting Lossy Compression Processes to Lossless

DTIC Science & Technology

1993-12-01

0~0 S* NAVAL POSTGRADUATE SCHOOL Monterey, California DTIC ELECTE THESIS S APR 11 1994DU A SIMPLE, LOW OVERHEAD DATA COMPRESSION ALGORITHM FOR...A SIMPLE. LOW OVERHEAD DATA COMPRESSION ALGORITHM FOR CONVERTING LOSSY COMPRESSION PROCESSES TO LOSSLESS. 6. AUTHOR(S) Abbott, Walter D., III 7...Approved for public release; distribution is unlimited. A Simple, Low Overhead Data Compression Algorithm for Converting Lossy Processes to Lossless by

Levitating a Magnet Using a Superconductive Material.

ERIC Educational Resources Information Center

Juergens, Frederick H.; And Others

1987-01-01

Presented are the materials and a procedure for demonstrating the levitation of a magnet above a superconducting material. The demonstration can be projected with an overhead projector for a large group of students. Kits to simplify the demonstration can be purchased from the Institute for Chemical Education of the University of Wisconsin-Madison.…

Display device for indicating the value of a parameter in a process plant

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Indicator system for advanced nuclear plant control complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Indicator system for a process plant control complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Console for a nuclear control complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Alarm system for a nuclear control complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1994-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Method of installing a control room console in a nuclear power plant

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1994-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Advanced nuclear plant control complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Advanced nuclear plant control room complex

DOEpatents

Scarola, Kenneth; Jamison, David S.; Manazir, Richard M.; Rescorl, Robert L.; Harmon, Daryl L.

1993-01-01

An advanced control room complex for a nuclear power plant, including a discrete indicator and alarm system (72) which is nuclear qualified for rapid response to changes in plant parameters and a component control system (64) which together provide a discrete monitoring and control capability at a panel (14-22, 26, 28) in the control room (10). A separate data processing system (70), which need not be nuclear qualified, provides integrated and overview information to the control room and to each panel, through CRTs (84) and a large, overhead integrated process status overview board (24). The discrete indicator and alarm system (72) and the data processing system (70) receive inputs from common plant sensors and validate the sensor outputs to arrive at a representative value of the parameter for use by the operator during both normal and accident conditions, thereby avoiding the need for him to assimilate data from each sensor individually. The integrated process status board (24) is at the apex of an information hierarchy that extends through four levels and provides access at each panel to the full display hierarchy. The control room panels are preferably of a modular construction, permitting the definition of inputs and outputs, the man machine interface, and the plant specific algorithms, to proceed in parallel with the fabrication of the panels, the installation of the equipment and the generic testing thereof.

Development of high performance scientific components for interoperability of computing packages

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gulabani, Teena Pratap

2008-01-01

Three major high performance quantum chemistry computational packages, NWChem, GAMESS and MPQC have been developed by different research efforts following different design patterns. The goal is to achieve interoperability among these packages by overcoming the challenges caused by the different communication patterns and software design of each of these packages. A chemistry algorithm is hard to develop as well as being a time consuming process; integration of large quantum chemistry packages will allow resource sharing and thus avoid reinvention of the wheel. Creating connections between these incompatible packages is the major motivation of the proposed work. This interoperability is achievedmore » by bringing the benefits of Component Based Software Engineering through a plug-and-play component framework called Common Component Architecture (CCA). In this thesis, I present a strategy and process used for interfacing two widely used and important computational chemistry methodologies: Quantum Mechanics and Molecular Mechanics. To show the feasibility of the proposed approach the Tuning and Analysis Utility (TAU) has been coupled with NWChem code and its CCA components. Results show that the overhead is negligible when compared to the ease and potential of organizing and coping with large-scale software applications.« less

18 CFR 367.52 - Overhead construction costs.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ACT Service Company Property Instructions § 367.52 Overhead construction costs. (a) All overhead construction costs, such as engineering, supervision, general office salaries and expenses, construction... costs. 367.52 Section 367.52 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY...

18 CFR 367.52 - Overhead construction costs.

Code of Federal Regulations, 2012 CFR

2012-04-01

... ACT Service Company Property Instructions § 367.52 Overhead construction costs. (a) All overhead construction costs, such as engineering, supervision, general office salaries and expenses, construction... costs. 367.52 Section 367.52 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY...

Fault tolerance in an inner-outer solver: A GVR-enabled case study

DOE PAGES

Zhang, Ziming; Chien, Andrew A.; Teranishi, Keita

2015-04-18

Resilience is a major challenge for large-scale systems. It is particularly important for iterative linear solvers, since they take much of the time of many scientific applications. We show that single bit flip errors in the Flexible GMRES iterative linear solver can lead to high computational overhead or even failure to converge to the right answer. Informed by these results, we design and evaluate several strategies for fault tolerance in both inner and outer solvers appropriate across a range of error rates. We implement them, extending Trilinos’ solver library with the Global View Resilience (GVR) programming model, which provides multi-streammore » snapshots, multi-version data structures with portable and rich error checking/recovery. Lastly, experimental results validate correct execution with low performance overhead under varied error conditions.« less

Characteristics and Clinical Outcomes in Overhead Sports Athletes after Rotator Cuff Repair

PubMed Central

Inui, Hiroaki; Ninomiya, Hiroki; Tanaka, Hiroshi; Nobuhara, Katsuya

2017-01-01

Rotator cuff tears in young overhead sports athletes are rare. The pathomechanism causing rotator cuff tears in young overhead athletes is different from that in aged patients. The purpose of this study was to investigate rotator cuff tear characteristics in young overhead sports athletes to reveal the pathomechanism causing these injuries. This study included 25 overhead sports athletes less than 30 years old with atraumatic rotator cuff tears necessitating repair. Rotator cuff tear characteristics were evaluated intraoperatively, including rotator cuff tear shape and injured rotator cuff tendon. Clinical outcome measures were assessed before surgery and at the final follow-up. In this study, 22 patients reported minimal to no shoulder pain and returned to sports without significant complaints at last follow-up. The isolated infraspinatus tendon was most often injured; the incidence rate of the tear at this site was 32% (8 cases). In the deceleration phase of overhead motion, the eccentric contraction force of the ISP (infraspinatus) tendon peaks and the increased load leads to injury at the ISP tendon. The pathomechanism of rotator cuff injuries in young overhead athletes might be not only internal or subacromial impingement, but also these mechanisms. PMID:28702502

Cluster-Based Multipolling Sequencing Algorithm for Collecting RFID Data in Wireless LANs

NASA Astrophysics Data System (ADS)

Choi, Woo-Yong; Chatterjee, Mainak

2015-03-01

With the growing use of RFID (Radio Frequency Identification), it is becoming important to devise ways to read RFID tags in real time. Access points (APs) of IEEE 802.11-based wireless Local Area Networks (LANs) are being integrated with RFID networks that can efficiently collect real-time RFID data. Several schemes, such as multipolling methods based on the dynamic search algorithm and random sequencing, have been proposed. However, as the number of RFID readers associated with an AP increases, it becomes difficult for the dynamic search algorithm to derive the multipolling sequence in real time. Though multipolling methods can eliminate the polling overhead, we still need to enhance the performance of the multipolling methods based on random sequencing. To that extent, we propose a real-time cluster-based multipolling sequencing algorithm that drastically eliminates more than 90% of the polling overhead, particularly so when the dynamic search algorithm fails to derive the multipolling sequence in real time.

PID temperature controller in pig nursery: spatial characterization of thermal environment

NASA Astrophysics Data System (ADS)

de Souza Granja Barros, Juliana; Rossi, Luiz Antonio; Menezes de Souza, Zigomar

2018-05-01

The use of enhanced technologies of temperature control can improve the thermal conditions in environments of livestock facilities. The objective of this study was to evaluate the spatial distribution of the thermal environment variables in a pig nursery with a heating system with two temperature control technologies based on the geostatistical analysis. The following systems were evaluated: overhead electrical resistance with Proportional, Integral, and Derivative (PID) controller and overhead electrical resistance with a thermostat. We evaluated the climatic variables: dry bulb temperature (Tbs), air relative humidity (RH), temperature and humidity index (THI), and enthalpy in the winter, at 7:00, 12:00, and 18:00 h. The spatial distribution of these variables was mapped by kriging. The results showed that the resistance heating system with PID controllers improved the thermal comfort conditions in the pig nursery in the coldest hours, maintaining the spatial distribution of the air temperature more homogeneous in the pen. During the hottest weather, neither system provided comfort.

PID temperature controller in pig nursery: spatial characterization of thermal environment

NASA Astrophysics Data System (ADS)

de Souza Granja Barros, Juliana; Rossi, Luiz Antonio; Menezes de Souza, Zigomar

2017-11-01

The use of enhanced technologies of temperature control can improve the thermal conditions in environments of livestock facilities. The objective of this study was to evaluate the spatial distribution of the thermal environment variables in a pig nursery with a heating system with two temperature control technologies based on the geostatistical analysis. The following systems were evaluated: overhead electrical resistance with Proportional, Integral, and Derivative (PID) controller and overhead electrical resistance with a thermostat. We evaluated the climatic variables: dry bulb temperature (Tbs), air relative humidity (RH), temperature and humidity index (THI), and enthalpy in the winter, at 7:00, 12:00, and 18:00 h. The spatial distribution of these variables was mapped by kriging. The results showed that the resistance heating system with PID controllers improved the thermal comfort conditions in the pig nursery in the coldest hours, maintaining the spatial distribution of the air temperature more homogeneous in the pen. During the hottest weather, neither system provided comfort.

78 FR 77027 - Overhead Clearance (Air-Draft) Accidents

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-20

... No. USCG-2013-0466] Overhead Clearance (Air-Draft) Accidents AGENCY: Coast Guard, DHS. ACTION... clearance (air-draft) accidents. In its petition, which calls for vessel masters to be provided with accurate vertical air draft information, a maritime organization has described 16 overhead clearance...

Development and evaluation of a hand tracker using depth images captured from an overhead perspective.

PubMed

Czarnuch, Stephen; Mihailidis, Alex

2015-03-27

We present the development and evaluation of a robust hand tracker based on single overhead depth images for use in the COACH, an assistive technology for people with dementia. The new hand tracker was designed to overcome limitations experienced by the COACH in previous clinical trials. We train a random decision forest classifier using ∼5000 manually labeled, unbalanced, training images. Hand positions from the classifier are translated into task actions based on proximity to environmental objects. Tracker performance is evaluated using a large set of ∼24 000 manually labeled images captured from 41 participants in a fully-functional washroom, and compared to the system's previous colour-based hand tracker. Precision and recall were 0.994 and 0.938 for the depth tracker compared to 0.981 and 0.822 for the colour tracker with the current data, and 0.989 and 0.466 in the previous study. The improved tracking performance supports integration of the depth-based tracker into the COACH toward unsupervised, real-world trials. Implications for Rehabilitation The COACH is an intelligent assistive technology that can enable people with cognitive disabilities to stay at home longer, supporting the concept of aging-in-place. Automated prompting systems, a type of intelligent assistive technology, can help to support the independent completion of activities of daily living, increasing the independence of people with cognitive disabilities while reducing the burden of care experienced by caregivers. Robust motion tracking using depth imaging supports the development of intelligent assistive technologies like the COACH. Robust motion tracking also has application to other forms of assistive technologies including gaming, human-computer interaction and automated assessments.

Highly Efficient and Scalable Compound Decomposition of Two-Electron Integral Tensor and Its Application in Coupled Cluster Calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peng, Bo; Kowalski, Karol

The representation and storage of two-electron integral tensors are vital in large- scale applications of accurate electronic structure methods. Low-rank representation and efficient storage strategy of integral tensors can significantly reduce the numerical overhead and consequently time-to-solution of these methods. In this paper, by combining pivoted incomplete Cholesky decomposition (CD) with a follow-up truncated singular vector decomposition (SVD), we develop a decomposition strategy to approximately represent the two-electron integral tensor in terms of low-rank vectors. A systematic benchmark test on a series of 1-D, 2-D, and 3-D carbon-hydrogen systems demonstrates high efficiency and scalability of the compound two-step decomposition ofmore » the two-electron integral tensor in our implementation. For the size of atomic basis set N_b ranging from ~ 100 up to ~ 2, 000, the observed numerical scaling of our implementation shows O(N_b^{2.5~3}) versus O(N_b^{3~4}) of single CD in most of other implementations. More importantly, this decomposition strategy can significantly reduce the storage requirement of the atomic-orbital (AO) two-electron integral tensor from O(N_b^4) to O(N_b^2 log_{10}(N_b)) with moderate decomposition thresholds. The accuracy tests have been performed using ground- and excited-state formulations of coupled- cluster formalism employing single and double excitations (CCSD) on several bench- mark systems including the C_{60} molecule described by nearly 1,400 basis functions. The results show that the decomposition thresholds can be generally set to 10^{-4} to 10^{-3} to give acceptable compromise between efficiency and accuracy.« less

KSC-08pd2347

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – Technicians in the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center install a specialized overhead crane onto the Fine Guidance Sensor, or FGS. The sensor will be lifted and moved to the Orbital Replacement Unit Carrier or ORUC, for installation. An FGS consists of a large structure housing a collection of mirrors, lenses, servos, prisms, beam splitters and photomultiplier tubes. There are three fine guidance sensors on Hubble located at 90-degree intervals around the circumference of the telescope. Along with the gyroscopes, the optical sensors are a key component of Hubble’s highly complex but extraordinarily effective “pointing control system.” The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125, on space shuttle Atlantis. Launch is targeted for Oct. 8. Photo credit: NASA/Jim Grossmann

KSC-08pd2348

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – A specialized overhead crane lifts the Fine Guidance Sensor, or FGS, in the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center. The sensor will be moved to the Orbital Replacement Unit Carrier, or ORUC, for installation. An FGS consists of a large structure housing a collection of mirrors, lenses, servos, prisms, beam splitters and photomultiplier tubes. There are three fine guidance sensors on Hubble located at 90-degree intervals around the circumference of the telescope. Along with the gyroscopes, the optical sensors are a key component of Hubble’s highly complex but extraordinarily effective “pointing control system.” The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125, on space shuttle Atlantis. Launch is targeted for Oct. 8. Photo credit: NASA/Jim Grossmann

KSC-08pd2346

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – Technicians in the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center help guide a specialized overhead crane toward the Fine Guidance Sensor, or FGS. The sensor will be lifted and moved to the Orbital Replacement Unit Carrier or ORUC, for installation. An FGS consists of a large structure housing a collection of mirrors, lenses, servos, prisms, beam splitters and photomultiplier tubes. There are three fine guidance sensors on Hubble located at 90-degree intervals around the circumference of the telescope. Along with the gyroscopes, the optical sensors are a key component of Hubble’s highly complex but extraordinarily effective “pointing control system.” The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125, on space shuttle Atlantis. Launch is targeted for Oct. 8. Photo credit: NASA/Jim Grossmann

Technicians complete assembly of Hubble Space Telescope (HST) mockup at JSC

NASA Technical Reports Server (NTRS)

1989-01-01

Technicians complete assembly of the Hubble Space Telescope (HST) mockup at JSC's Mockup and Integration Laboratory (MAIL) Bldg 9A. In the foreground, a technician holds the controls for an overhead crane attached to one of the HST's high gain antennas (HGAs). Technicians on the ground prepare the HGA to be hoisted into position on the mockup's Support System Module (SSM) forward shell as others work on SSM from a cherry picker.

Memory-Based Structured Application Specific Integrated Circuit (ASIC) Study

DTIC Science & Technology

2008-10-01

memory interface, arbiter/ schedulers for rescheduling the memory requests according to some schedule policy, and memory channels for communicating...between the power-savings and the wakeup overhead with respect to both wakeup power and wakeup delay. For example, dream mode can save 50% more static...power than sleep mode, but at the expense of twice the wake delay and three times the wakeup energy. The user can specify power-gating modes for various components.

A depth-first search algorithm to compute elementary flux modes by linear programming.

PubMed

Quek, Lake-Ee; Nielsen, Lars K

2014-07-30

The decomposition of complex metabolic networks into elementary flux modes (EFMs) provides a useful framework for exploring reaction interactions systematically. Generating a complete set of EFMs for large-scale models, however, is near impossible. Even for moderately-sized models (<400 reactions), existing approaches based on the Double Description method must iterate through a large number of combinatorial candidates, thus imposing an immense processor and memory demand. Based on an alternative elementarity test, we developed a depth-first search algorithm using linear programming (LP) to enumerate EFMs in an exhaustive fashion. Constraints can be introduced to directly generate a subset of EFMs satisfying the set of constraints. The depth-first search algorithm has a constant memory overhead. Using flux constraints, a large LP problem can be massively divided and parallelized into independent sub-jobs for deployment into computing clusters. Since the sub-jobs do not overlap, the approach scales to utilize all available computing nodes with minimal coordination overhead or memory limitations. The speed of the algorithm was comparable to efmtool, a mainstream Double Description method, when enumerating all EFMs; the attrition power gained from performing flux feasibility tests offsets the increased computational demand of running an LP solver. Unlike the Double Description method, the algorithm enables accelerated enumeration of all EFMs satisfying a set of constraints.

The isokinetic rotator cuff strength ratios in overhead athletes: Assessment and exercise effect.

PubMed

Berckmans, Kelly; Maenhout, Annelies G; Matthijs, Lien; Pieters, Louise; Castelein, Birgit; Cools, Ann M

2017-09-01

Muscle strength imbalance in the shoulder region can be considered as a predisposing factor in the development of movement dysfunctions, possibly leading to overuse injuries. Repetitive overhead throwing, performed in sports, may result in muscle imbalance between the external (ER) and internal (IR) rotators. Muscle strength measured with an isokinetic device, is reported as a concentric (CON) or eccentric (ECC) force. The balance between an agonist and an antagonist is mentioned as a ratio (CON/CON or ECC/CON). The aim of this systematic literature review is to provide an overview of the existing evidence considering the isokinetic muscle strength ratios of ER and IR of the shoulder in healthy overhead athletes. In addition, the effect of exercise programs on these ratios was investigated. Two online databases (Web of Science and PubMed) were consulted using different search strategies. Articles were selected based on inclusion and exclusion criteria. All included articles were assessed on their methodological quality. There is moderate evidence for a lower functional deceleration ratio (ECC ER/CON IR) at the dominant side. This lower ratio is due to a large overweight of CON IR strength on that side. There is no consensus about which exercise program is the most effective in altering the shoulder isokinetic strength ratios. Copyright © 2017 Elsevier Ltd. All rights reserved.

Field evaluation of unlighted overhead guide signs using older drivers : executive summary report.

DOT National Transportation Integrated Search

2003-08-01

Problem: In the preceding Unlighted Overhead Guide : Sign Feasibility Study, it was determined that : the lighting of overhead guide signs on : freeways could be eliminated if white : microprismatic Type VII or Type IX legends : were used on green be...

Data base systems in electronic design engineering

NASA Technical Reports Server (NTRS)

Williams, D.

1980-01-01

The concepts of an integrated design data base system (DBMS) as it might apply to an electronic design company are discussed. Data elements of documentation, project specifications, project tracking, firmware, software, electronic and mechanical design can be integrated and managed through a single DBMS. Combining the attributes of a DBMS data handler with specialized systems and functional data can provide users with maximum flexibility, reduced redundancy, and increased overall systems performance. Although some system overhead is lost due to redundancy in transitory data, it is believed the combination of the two data types is advisable rather than trying to do all data handling through a single DBMS.

KSC-01pp0249

NASA Image and Video Library

2001-02-03

An overhead crane lowers the Multi-Purpose Logistics Module Donatello onto a workstand. In the SSPF, Donatello will undergo processing by the payload test team, including integrated electrical tests with other Station elements in the SSPF, leak tests, electrical and software compatibility tests with the Space Shuttle (using the Cargo Integrated Test equipment) and an Interface Verification Test once the module is installed in the Space Shuttle’s payload bay at the launch pad. The most significant mechanical task to be performed on Donatello in the SSPF is the installation and outfitting of the racks for carrying the various experiments and cargo. Donatello will be launched on mission STS-130, currently planned for September 2004

Analysis of Parallel Algorithms on SMP Node and Cluster of Workstations Using Parallel Programming Models with New Tile-based Method for Large Biological Datasets.

PubMed

Shrimankar, D D; Sathe, S R

2016-01-01

Sequence alignment is an important tool for describing the relationships between DNA sequences. Many sequence alignment algorithms exist, differing in efficiency, in their models of the sequences, and in the relationship between sequences. The focus of this study is to obtain an optimal alignment between two sequences of biological data, particularly DNA sequences. The algorithm is discussed with particular emphasis on time, speedup, and efficiency optimizations. Parallel programming presents a number of critical challenges to application developers. Today's supercomputer often consists of clusters of SMP nodes. Programming paradigms such as OpenMP and MPI are used to write parallel codes for such architectures. However, the OpenMP programs cannot be scaled for more than a single SMP node. However, programs written in MPI can have more than single SMP nodes. But such a programming paradigm has an overhead of internode communication. In this work, we explore the tradeoffs between using OpenMP and MPI. We demonstrate that the communication overhead incurs significantly even in OpenMP loop execution and increases with the number of cores participating. We also demonstrate a communication model to approximate the overhead from communication in OpenMP loops. Our results are astonishing and interesting to a large variety of input data files. We have developed our own load balancing and cache optimization technique for message passing model. Our experimental results show that our own developed techniques give optimum performance of our parallel algorithm for various sizes of input parameter, such as sequence size and tile size, on a wide variety of multicore architectures.

Analysis of Parallel Algorithms on SMP Node and Cluster of Workstations Using Parallel Programming Models with New Tile-based Method for Large Biological Datasets

PubMed Central

Shrimankar, D. D.; Sathe, S. R.

2016-01-01

Sequence alignment is an important tool for describing the relationships between DNA sequences. Many sequence alignment algorithms exist, differing in efficiency, in their models of the sequences, and in the relationship between sequences. The focus of this study is to obtain an optimal alignment between two sequences of biological data, particularly DNA sequences. The algorithm is discussed with particular emphasis on time, speedup, and efficiency optimizations. Parallel programming presents a number of critical challenges to application developers. Today’s supercomputer often consists of clusters of SMP nodes. Programming paradigms such as OpenMP and MPI are used to write parallel codes for such architectures. However, the OpenMP programs cannot be scaled for more than a single SMP node. However, programs written in MPI can have more than single SMP nodes. But such a programming paradigm has an overhead of internode communication. In this work, we explore the tradeoffs between using OpenMP and MPI. We demonstrate that the communication overhead incurs significantly even in OpenMP loop execution and increases with the number of cores participating. We also demonstrate a communication model to approximate the overhead from communication in OpenMP loops. Our results are astonishing and interesting to a large variety of input data files. We have developed our own load balancing and cache optimization technique for message passing model. Our experimental results show that our own developed techniques give optimum performance of our parallel algorithm for various sizes of input parameter, such as sequence size and tile size, on a wide variety of multicore architectures. PMID:27932868

Consumer Security Perceptions and the Perceived Influence on Adopting Cloud Computing: A Quantitative Study Using the Technology Acceptance Model

ERIC Educational Resources Information Center

Paquet, Katherine G.

2013-01-01

Cloud computing may provide cost benefits for organizations by eliminating the overhead costs of software, hardware, and maintenance (e.g., license renewals, upgrading software, servers and their physical storage space, administration along with funding a large IT department). In addition to the promised savings, the organization may require…

Taking It to the Streets: Mobile CD-ROM Workshops on Campus.

ERIC Educational Resources Information Center

Parker-Gibson, Necia

1994-01-01

Librarians at the University of Arkansas (Fayetteville) offer CD-ROM database and online catalog training using a portable unit composed of a laptop computer, modem, LCD panel, and overhead projector. This unit allows librarians to make presentations to large groups and to demonstrate to faculty and students the relevancy of library technology.…

Vegetation clearance distances to prevent wildland fire caused damage to telecommunication and power transmission infrastructure (2)

Treesearch

B. W. Butler; T. Wallace; J. Hogge

2015-01-01

Towers and poles supporting power transmission and telecommunication lines have collapsed due to heating from wildland fires. Such occurrences have led to interruptions in power or communication in large municipal areas with associated social and political implications as well as increased immediate danger to humans. Vegetation clearance standards for overhead...

Field evaluation of unlighted overhead guide signs using older drivers : research implementation plan.

DOT National Transportation Integrated Search

2006-04-01

STATEMENT OF NEED: In the preceding Unlighted Overhead Guide Sign Feasibility Study, it was determined that the lighting of overhead : guide signs on freeways could be eliminated if white micro-prismatic Type VII or Type IX legends were used on : gre...

Structural health monitoring of compression connectors for overhead transmission lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Hong; Wang, Jy-An John; Swindeman, Joseph P

Two-stage aluminum conductor steel-reinforced (ACSR) compression connectors are extensively used in US overhead transmission lines. The connectors are made by crimping a steel sleeve onto a steel core and an aluminum sleeve over aluminum conductive strands. The connectors are designed to operate at temperatures up to 125 C, but their performance is increasingly degrading because of overloading of lines. Currently, electric utilities conduct routine line inspections using thermal and electrical measurements. However, information about the structural integrity of connectors cannot be obtained. In this work, structural health monitoring (SHM) of compression connectors was studied using electromechanical impedance (EMI) analysis. Leadmore » zirconate titanate (PZT)-5A was identified as a smart material for SHM. A flexible high-temperature bonding layer was used to address challenges in PZT integration due to a significant difference in the coefficients of thermal expansion of PZT and the aluminum substrate. The steel joint on the steel core was investigated because it is responsible for the ultimate tensile strength of the connector. Tensile testing was used to create structural damage to the joint, or steel core pullout, and thermal cycling introduced additional structural perturbations. EMI measurements were conducted between the tests. The root mean square deviation (RMSD) of EMI was identified as a damage index. The use of steel joints has been shown to enable SHM under simulated conditions. The EMI signature is sensitive to variations in structural conditions. RMSD can be correlated to the structural health of a connector and has potential for use in the SHM and structural integrity evaluation.« less

Structural health monitoring of compression connectors for overhead transmission lines

NASA Astrophysics Data System (ADS)

Wang, Hong; Wang, Jy-An John; Swindeman, Joseph P.; Ren, Fei; Chan, John

2017-04-01

Two-stage aluminum conductor steel-reinforced (ACSR) compression connectors are extensively used in US overhead transmission lines. The connectors are made by crimping a steel sleeve onto a steel core and an aluminum sleeve over electrical conducting aluminum strands. The connectors are designed to operate at temperatures up to 125°C, but their performance is increasingly degrading because of overloading of lines. Currently, electric utilities conduct routine line inspections using thermal and electrical measurements, but these methods do not provide information about the structural integrity of connectors. In this work, structural health monitoring (SHM) of compression connectors was studied using electromechanical impedance (EMI) analysis. Lead zirconate titanate (PZT)-5A was identified as a smart material for SHM. A flexible high-temperature bonding layer was used to address challenges in PZT integration due to a significant difference in the coefficients of thermal expansion of PZT and the aluminum substrate. The steel joint on the steel core was investigated because it is responsible for the ultimate tensile strength of the connector. Tensile testing was used to induce structural damage to the joint, or steel core pullout, and thermal cycling introduced additional structural perturbations. EMI measurements were conducted between the tests. The root mean square deviation (RMSD) of EMI was identified as a damage index. The use of steel joints has been shown to enable SHM under simulated conditions. The EMI signature is sensitive to variations in structural conditions. RMSD can be correlated to the structural health of a connector and has potential for use in the SHM and structural integrity evaluation.

An integrated gateway for various PHDs in U-healthcare environments.

PubMed

Park, KeeHyun; Pak, JuGeon

2012-01-01

We propose an integrated gateway for various personal health devices (PHDs). This gateway receives measurements from various PHDs and conveys them to a remote monitoring server (MS). It provides two kinds of transmission modes: immediate transmission and integrated transmission. The former mode operates if a measurement exceeds a predetermined threshold or in the case of an emergency. In the latter mode, the gateway retains the measurements instead of forwarding them. When the reporting time comes, the gateway extracts all the stored measurements, integrates them into one message, and transmits the integrated message to the MS. Through this mechanism, the transmission overhead can be reduced. On the basis of the proposed gateway, we construct a u-healthcare system comprising an activity monitor, a medication dispenser, and a pulse oximeter. The evaluation results show that the size of separate messages from various PHDs is reduced through the integration process, and the process does not require much time; the integration time is negligible.

An Integrated Gateway for Various PHDs in U-Healthcare Environments

PubMed Central

Park, KeeHyun; Pak, JuGeon

2012-01-01

We propose an integrated gateway for various personal health devices (PHDs). This gateway receives measurements from various PHDs and conveys them to a remote monitoring server (MS). It provides two kinds of transmission modes: immediate transmission and integrated transmission. The former mode operates if a measurement exceeds a predetermined threshold or in the case of an emergency. In the latter mode, the gateway retains the measurements instead of forwarding them. When the reporting time comes, the gateway extracts all the stored measurements, integrates them into one message, and transmits the integrated message to the MS. Through this mechanism, the transmission overhead can be reduced. On the basis of the proposed gateway, we construct a u-healthcare system comprising an activity monitor, a medication dispenser, and a pulse oximeter. The evaluation results show that the size of separate messages from various PHDs is reduced through the integration process, and the process does not require much time; the integration time is negligible. PMID:22899891

Customized overhead cranes for installation of India's largest 3.6m optical telescope at Devasthal, Nainital, India

NASA Astrophysics Data System (ADS)

Bangia, Tarun; Yadava, Shobhit; Kumar, Brijesh; Ghanti, A. S.; Hardikar, P. M.

2016-07-01

India's largest 3.6 m aperture optical telescope facility has been recently established at Devasthal site by Aryabhatta Research Institute of Observation Sciences (ARIES), an autonomous Institute under Department of Science and Technology, Government of India. The telescope is equipped with active optics and it is designed to be used for seeinglimited observations at visible and near-infrared wavelengths. A steel building with rotating cylindrical steel Dome was erected to house 3.6m telescope and its accessories at hilltop of Devasthal site. Customized cranes were essentially required inside the building as there were space constraints around the telescope building for operating big external heavy duty cranes from outside, transportation constraints in route for bringing heavy weight cranes, altitude of observatory, and sharp bends etc. to site. To meet the challenge of telescope installation from inside the telescope building by lifting components through its hatch, two Single Girder cranes and two Under Slung cranes of 10 MT capacity each were specifically designed and developed. All the four overhead cranes were custom built to achieve the goal of handling telescope mirror and its various components during installation and assembly. Overhead cranes were installed in limited available space inside the building and tested as per IS 3177. Cranes were equipped with many features like VVVFD compatibility, provision for tandem operation, digital load display, anti-collision mechanism, electrical interlocks, radio remote, low hook height and compact carriage etc. for telescope integration at site.

Afghan Air Force University: Contract Requirements Were Generally Met, but Instances of Non Compliance, Poor Workmanship, and Inadequate Maintenance Need to Be Addressed

DTIC Science & Technology

2016-03-01

work included installing new doors and windows, new plumbing fixtures, and overhead lighting, fresh paint, and tile work in 15 buildings and new...ceramic tile work in some buildings. These issues can largely be attributed to USACE’s failure to (1) fully monitor the implementation of its three-phase...and 3 support structures. The building renovations largely consisted of replacing doors, windows, carpeting, tiles , bathroom fixtures, and fans, as

49 CFR 214.515 - Overhead covers for existing on-track roadway maintenance machines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... previously equipped with overhead covers for the operator's position, defective covers shall be repaired, and missing covers shall be reinstalled, by March 28, 2005 and thereafter maintained in accordance with the... equipped with overhead covers for the operator's position, the employer shall evaluate the feasibility of...

1. EAST SIDE OF OVERHEAD BOMB TRANSPORT RACK, WITH BUILDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. EAST SIDE OF OVERHEAD BOMB TRANSPORT RACK, WITH BUILDING 343 AT LEFT AND BUILDING 328 AT RIGHT. VIEW TO WEST. - Rocky Mountain Arsenal, Overhead Bomb Transport Rack, 1580 feet South of December Seventh Avenue; 860 feet West of D Street, Commerce City, Adams County, CO

Surface code implementation of block code state distillation.

PubMed

Fowler, Austin G; Devitt, Simon J; Jones, Cody

2013-01-01

State distillation is the process of taking a number of imperfect copies of a particular quantum state and producing fewer better copies. Until recently, the lowest overhead method of distilling states produced a single improved [formula: see text] state given 15 input copies. New block code state distillation methods can produce k improved [formula: see text] states given 3k + 8 input copies, potentially significantly reducing the overhead associated with state distillation. We construct an explicit surface code implementation of block code state distillation and quantitatively compare the overhead of this approach to the old. We find that, using the best available techniques, for parameters of practical interest, block code state distillation does not always lead to lower overhead, and, when it does, the overhead reduction is typically less than a factor of three.

Surface code implementation of block code state distillation

PubMed Central

Fowler, Austin G.; Devitt, Simon J.; Jones, Cody

2013-01-01

State distillation is the process of taking a number of imperfect copies of a particular quantum state and producing fewer better copies. Until recently, the lowest overhead method of distilling states produced a single improved |A〉 state given 15 input copies. New block code state distillation methods can produce k improved |A〉 states given 3k + 8 input copies, potentially significantly reducing the overhead associated with state distillation. We construct an explicit surface code implementation of block code state distillation and quantitatively compare the overhead of this approach to the old. We find that, using the best available techniques, for parameters of practical interest, block code state distillation does not always lead to lower overhead, and, when it does, the overhead reduction is typically less than a factor of three. PMID:23736868

Implicit Block ACK Scheme for IEEE 802.11 WLANs

PubMed Central

Sthapit, Pranesh; Pyun, Jae-Young

2016-01-01

The throughput of IEEE 802.11 standard is significantly bounded by the associated Medium Access Control (MAC) overhead. Because of the overhead, an upper limit exists for throughput, which is bounded, including situations where data rates are extremely high. Therefore, an overhead reduction is necessary to achieve higher throughput. The IEEE 802.11e amendment introduced the block ACK mechanism, to reduce the number of control messages in MAC. Although the block ACK scheme greatly reduces overhead, further improvements are possible. In this letter, we propose an implicit block ACK method that further reduces the overhead associated with IEEE 802.11e’s block ACK scheme. The mathematical analysis results are presented for both the original protocol and the proposed scheme. A performance improvement of greater than 10% was achieved with the proposed implementation.

Validation of Objective Based Measures and Development of a Performance-Based Ranking Method for Load Carriage Systems

DTIC Science & Technology

2001-05-01

Shoulder Discomfort, March Thermal Comfort z * Front Mobility, Overhead Mobility, March Thermal Comfort r Moment (Amp, Nm/kg) x * Torsional Mobility...0 Fit El Manoeuverability U Acceptability M Integration 0 Mobility 0 Physical Comfort 0 Thermal Comfort Figure 3. Overall Ratings for Four Systems. A... Thermal Comfort ) Total 71.1 % Factor 1 described the balance and general ability to move with the pack in place. Variables included lateral bending

Technicians assembly the Hubble Space Telescope (HST) mockup at JSC

NASA Technical Reports Server (NTRS)

1989-01-01

At JSC's Mockup and Integration Laboratory (MAIL) Bldg 9A, technicians install a high gain antenna (HGA) on the Hubble Space Telescope (HST) mockup. On the ground a technician operates the controls for the overhead crane that is lifting the HGA into place on the Support System Module (SSM) forward shell. Others in a cherry picker basket wait for the HGA to near its final position so they can secure it on the mockup.

Versioned distributed arrays for resilience in scientific applications: Global view resilience

DOE PAGES

Chien, A.; Balaji, P.; Beckman, P.; ...

2015-06-01

Exascale studies project reliability challenges for future high-performance computing (HPC) systems. We propose the Global View Resilience (GVR) system, a library that enables applications to add resilience in a portable, application-controlled fashion using versioned distributed arrays. We describe GVR’s interfaces to distributed arrays, versioning, and cross-layer error recovery. Using several large applications (OpenMC, the preconditioned conjugate gradient solver PCG, ddcMD, and Chombo), we evaluate the programmer effort to add resilience. The required changes are small (<2% LOC), localized, and machine-independent, requiring no software architecture changes. We also measure the overhead of adding GVR versioning and show that generally overheads <2%more » are achieved. We conclude that GVR’s interfaces and implementation are flexible and portable and create a gentle-slope path to tolerate growing error rates in future systems.« less

Preliminary Report on Oak Ridge National Laboratory Testing of Drake/ACSS/MA2/E3X

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irminger, Philip; King, Daniel J.; Herron, Andrew N.

2016-01-01

A key to industry acceptance of a new technology is extensive validation in field trials. The Powerline Conductor Accelerated Test facility (PCAT) at Oak Ridge National Laboratory (ORNL) is specifically designed to evaluate the performance and reliability of a new conductor technology under real world conditions. The facility is set up to capture large amounts of data during testing. General Cable used the ORNL PCAT facility to validate the performance of TransPowr with E3X Technology a standard overhead conductor with an inorganic high emissivity, low absorptivity surface coating. Extensive testing has demonstrated a significant improvement in conductor performance across amore » wide range of operating temperatures, indicating that E3X Technology can provide a reduction in temperature, a reduction in sag, and an increase in ampacity when applied to the surface of any overhead conductor. This report provides initial results of that testing.« less

77 FR 53914 - Horton Automatics, Inc., a Subsidiary of Overhead Door Corporation Including On-Site Leased...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

...., a Subsidiary of Overhead Door Corporation Including On-Site Leased Workers From Remedy Intelligent..., including on-site leased workers from Remedy Intelligent Staffing, Corpus Christi, Texas. The workers are... Automatics, Inc., a subsidiary of Overhead Door Corporation, including on-site leased workers from Remedy...

Overhead Projector Spectrum of Polymethine Dye: A Physical Chemistry Demonstration

NASA Astrophysics Data System (ADS)

Solomon, Sally; Hur, Chinhyu

1995-08-01

The position of the predominant peak of 1,1'-diethyl-4,4'-cyanine iodide is measured in class using an overhead projector spectrometer, then predicted using the model of a particle-in a one dimensional box. The calculated wavelength is in excellent agreement with the wavelength estimated from the overhead projector spectroscopy experiment.

Geography via the Overhead Projector: Do It This Way, 7.

ERIC Educational Resources Information Center

Best, Thomas D.

This booklet is designed to assist teachers in their use of overhead projectors when teaching geography. With the overhead technique, relationships among patterns can be suggested bit by bit on inexpensive, easily prepared overlays that are projected to sizes appropriate for a particular instructional situation. A general discussion of the…

Report on Analyses of WAC Samples of Evaporator Overheads - 2004

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oji, L

2005-03-18

In November and December of 2004, the Tank Farm submitted annual samples from 2F, 2H and 3H Evaporator Overhead streams for characterization to verify compliance with the new Effluent Treatment Facility (ETF) Waste Acceptance Criteria (WAC) and to look for organic species. With the exception of slightly high ammonia in the 2F evaporator overheads and high radiation control guide number for the 3H and 2F evaporator overhead samples, all the overheads samples were found to be in compliance with the Effluent Treatment Facility WAC. The ammonium concentration in the 2F-evaporator overhead, at 33 mg/L, was above the ETF waste watermore » collection tank (WWCT) limits of 28 mg/L. The RCG Number for the 3H and 2F evaporator samples at, respectively, 1.38E-02 and 8.24E-03 were higher than the WWCT limit of 7.69E-03. The analytical detection limits for americium-241 and radium-226 in the evaporator samples were not consistently met because of low WWCT detection limits and insufficient evaporator samples.« less

Affinity+: Semi-Structured Brainstorming on Large Displays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burtner, Edwin R.; May, Richard A.; Scarberry, Randall E.

2013-04-27

Affinity diagraming is a powerful method for encouraging and capturing lateral thinking in a group environment. The Affinity+ Concept was designed to improve the collaborative brainstorm process through the use of large display surfaces in conjunction with mobile devices like smart phones and tablets. The system works by capturing the ideas digitally and allowing users to sort and group them on a large touch screen manually. Additionally, Affinity+ incorporates theme detection, topic clustering, and other processing algorithms that help bring structured analytic techniques to the process without requiring explicit leadership roles and other overhead typically involved in these activities.

Repairing Foam Insulation

NASA Technical Reports Server (NTRS)

Corbin, J.; Buras, D.

1986-01-01

Large holes in polyurethane foam insulation repaired reliably by simple method. Little skill needed to apply method, used for overhead repairs as well as for those in other orientations. Plug positioned in hole to be filled and held in place with mounting fixture. Fresh liquid foam injected through plug to bond it in place. As foam cures and expands, it displaces plug outward. Protrusion later removed.

Computer-based mechanical design of overhead lines

NASA Astrophysics Data System (ADS)

Rusinaru, D.; Bratu, C.; Dinu, R. C.; Manescu, L. G.

2016-02-01

Beside the performance, the safety level according to the actual standards is a compulsory condition for distribution grids’ operation. Some of the measures leading to improvement of the overhead lines reliability ask for installations’ modernization. The constraints imposed to the new lines components refer to the technical aspects as thermal stress or voltage drop, and look for economic efficiency, too. The mechanical sizing of the overhead lines is after all an optimization problem. More precisely, the task in designing of the overhead line profile is to size poles, cross-arms and stays and locate poles along a line route so that the total costs of the line's structure to be minimized and the technical and safety constraints to be fulfilled.The authors present in this paper an application for the Computer-Based Mechanical Design of the Overhead Lines and the features of the corresponding Visual Basic program, adjusted to the distribution lines. The constraints of the optimization problem are adjusted to the existing weather and loading conditions of Romania. The outputs of the software application for mechanical design of overhead lines are: the list of components chosen for the line: poles, cross-arms, stays; the list of conductor tension and forces for each pole, cross-arm and stay for different weather conditions; the line profile drawings.The main features of the mechanical overhead lines design software are interactivity, local optimization function and high-level user-interface

75 FR 44288 - Overhead and Gantry Cranes; Extension of the Office of Management and Budget's (OMB) Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-28

...] Overhead and Gantry Cranes; Extension of the Office of Management and Budget's (OMB) Approval of... requirements specified in the Standard on Overhead and Gantry Cranes (29 CFR 1910.179). DATES: Comments must be... requirements for: Marking the rated load of cranes; preparing certification records to verify the inspection of...

How To Prepare Effective Overhead Projector Presentations: One Picture Is Worth a Thousand Words.

ERIC Educational Resources Information Center

National Audio-Visual Supply, East Rutherford, NJ.

Designed to help create effective presentations, this guide describes the basic techniques and provides hints for producing professional, attention-getting overhead transparencies in a step-by-step procedure format. Eight topics are addressed in the guide: (1) eight steps to a successful meeting presentation; (2) advantages of overhead projection;…

Overhead Crane Computer Model

NASA Astrophysics Data System (ADS)

Enin, S. S.; Omelchenko, E. Y.; Fomin, N. V.; Beliy, A. V.

2018-03-01

The paper has a description of a computer model of an overhead crane system. The designed overhead crane system consists of hoisting, trolley and crane mechanisms as well as a payload two-axis system. With the help of the differential equation of specified mechanisms movement derived through Lagrange equation of the II kind, it is possible to build an overhead crane computer model. The computer model was obtained using Matlab software. Transients of coordinate, linear speed and motor torque of trolley and crane mechanism systems were simulated. In addition, transients of payload swaying were obtained with respect to the vertical axis. A trajectory of the trolley mechanism with simultaneous operation with the crane mechanism is represented in the paper as well as a two-axis trajectory of payload. The designed computer model of an overhead crane is a great means for studying positioning control and anti-sway control systems.

A depth-first search algorithm to compute elementary flux modes by linear programming

PubMed Central

2014-01-01

Background The decomposition of complex metabolic networks into elementary flux modes (EFMs) provides a useful framework for exploring reaction interactions systematically. Generating a complete set of EFMs for large-scale models, however, is near impossible. Even for moderately-sized models (<400 reactions), existing approaches based on the Double Description method must iterate through a large number of combinatorial candidates, thus imposing an immense processor and memory demand. Results Based on an alternative elementarity test, we developed a depth-first search algorithm using linear programming (LP) to enumerate EFMs in an exhaustive fashion. Constraints can be introduced to directly generate a subset of EFMs satisfying the set of constraints. The depth-first search algorithm has a constant memory overhead. Using flux constraints, a large LP problem can be massively divided and parallelized into independent sub-jobs for deployment into computing clusters. Since the sub-jobs do not overlap, the approach scales to utilize all available computing nodes with minimal coordination overhead or memory limitations. Conclusions The speed of the algorithm was comparable to efmtool, a mainstream Double Description method, when enumerating all EFMs; the attrition power gained from performing flux feasibility tests offsets the increased computational demand of running an LP solver. Unlike the Double Description method, the algorithm enables accelerated enumeration of all EFMs satisfying a set of constraints. PMID:25074068

KSC-02pd1286

NASA Image and Video Library

2002-09-05

KENNEDY SPACE CENTER, FLA. - Suspended from an overhead crane, the orbiter Atlantis is lowered toward the solid rocket booster and external tank below, on top of the Mobile Launcher Platform, for mating before rollout to the launch pad for mission STS-112. Launch is scheduled no earlier than Oct. 2 for the 15th assembly flight to the International Space Station. Atlantis will carry the S1 Integrated Truss Structure, which will be attached to the central truss segment, the S0 truss, during the mission.

Technicians complete assembly of Hubble Space Telescope (HST) mockup at JSC

NASA Technical Reports Server (NTRS)

1989-01-01

A technician listens to instructions as he operates the controls for the overhead crane that is lifting one of the Hubble Space Telescope (HST) high gain antennas (HGAs) into place on the HST Support System Module (SSM) forward shell. Others in a cherry picker basket wait to install the HGA on the SSM mockup. The HST mockup will be used for astronaut training and is being assembled in JSC's Mockup and Integration Laboratory (MAIL) Bldg 9A.

Multiprogramming performance degradation - Case study on a shared memory multiprocessor

NASA Technical Reports Server (NTRS)

Dimpsey, R. T.; Iyer, R. K.

1989-01-01

The performance degradation due to multiprogramming overhead is quantified for a parallel-processing machine. Measurements of real workloads were taken, and it was found that there is a moderate correlation between the completion time of a program and the amount of system overhead measured during program execution. Experiments in controlled environments were then conducted to calculate a lower bound on the performance degradation of parallel jobs caused by multiprogramming overhead. The results show that the multiprogramming overhead of parallel jobs consumes at least 4 percent of the processor time. When two or more serial jobs are introduced into the system, this amount increases to 5.3 percent

Effects of overhead work involving different heights and distances on neck and shoulder muscle activity.

PubMed

Shin, Seung-Je; Yoo, Won-Gyu

2015-06-05

Although overhead work is closely related to musculoskeletal disorders, it is difficult to avoid these postures in daily working conditions. In industrial tasks that require elevated arm postures above shoulder height, flexibility in the location of the task is necessary. This study investigated the sternocleidomastoid, upper trapezius, lower trapezius, and anterior deltoid, serratus anterior muscle activities during overhead work involving four different height and distance locations performed by healthy adult participants. Eighteen young male right-hand-dominant workers were recruited. The right upper trapezius, lower trapezius, serratus anterior, anterior deltoid, and sternocleidomastoid muscle activities were measured under for overhead work condition (Location 1: overhead work with a height of 10 cm above the head of each subject and distance of 15 cm, Location 2: overhead work with a height of 10 cm above the head of each subject and distance of 30 cm, Location 3: overhead work with a height of 20 cm above the head of each subject and distance of 15 cm, Location 4: overhead work with a height of 20 cm above the head of each subject and distance of 30 cm). In Location 3, there was significantly higher neck extension range of motion compared to Location 1, Location 2 and Location 4. In Location 1, the activities of the upper trapezius, lower trapezius, serratus anterior, anterior deltoid, and sternocleidomastoid muscles were significantly lower than those in Location 3 (p<0.05). In Location 2, the activities of the upper trapezius, lower trapezius, serratus anterior, anterior deltoid, and sternocleidomastoid muscles were significantly lower than those in Location 4 (p<0.05). In Location 1, there were significantly lower upper trapezius, lower trapezius, serratus anterior, and anterior deltoid muscle activities than in Location 2 (p<0.05). In Location 3, there were significantly lower upper trapezius, lower trapezius, serratus anterior, and anterior deltoid muscle activities than in Location 4 (p<0.05). In Location 1, there was significantly higher sternocleidomastoid muscle activity than in Location 2 (p<0.05). Finally, In Location 3, there was significantly higher sternocleidomastoid muscle activity than in Location 4 (p<0.05). Overhead workers should engage in work that involves a low height and near distance. Height appears to be a stronger risk factor than distance in overhead work.

Return-to-activity after anatomical reconstruction of acute high-grade acromioclavicular separation.

PubMed

Saier, T; Plath, J E; Beitzel, K; Minzlaff, P; Feucht, J M; Reuter, S; Martetschläger, F; Imhoff, Andreas B; Aboalata, M; Braun, S

2016-04-02

To evaluate return-to-activity (RtA) after anatomical reconstruction of acute high-grade acromioclavicular joint (ACJ) separation. A total of 42 patients with anatomical reconstruction of acute high-grade ACJ-separation (Rockwood Type V) were surveyed to determine RtA at a mean 31 months follow-up (f-u). Sports disciplines, intensity, level of competition, participation in overhead and/or contact sports, as well as activity scales (DASH-Sport-Module, Tegner Activity Scale) were evaluated. Functional outcome evaluation included Constant score and QuickDASH. All patients (42/42) participated in sporting activities at f-u. Neither participation in overhead/contact sports, nor level of activity declined significantly (n.s.). 62 % (n = 26) of patients reported subjective sports specific ACJ integrity to be at least the same as prior to the trauma. Sporting intensity (hours/week: 7.3 h to 5.4 h, p = .004) and level of competition (p = .02) were reduced. If activity changed, in 50 % other reasons but clinical symptoms/impairment were named for modified behavior. QuickDASH (mean 6, range 0-54, SD 11) and DASH-Sport-Module (mean 6, range 0-56, SD 13) revealed only minor disabilities at f-u. Over time Constant score improved significant to an excellent score (mean 94, range 86-100, SD 4; p < .001). Functional outcome was not correlated with RtA (n.s.). All patients participated in sporting activities after anatomical reconstruction of high-grade (Rockwood Type V) ACJ-separation. With a high functional outcome there was no significant change in activity level (Tegner) and participation in overhead and/or contact sports observed. There was no correlation between functional outcome and RtA. Limiting, there were alterations in time spent for sporting activities and level of competition observed. But in 50 % those were not related to ACJ symptoms/impairment. Unrelated to successful re-established integrity and function of the ACJ it should be considered that patients decided not return-to-activity but are very content with the procedure.

STS-36 Mission Specialist Hilmers with AEROLINHOF camera on aft flight deck

NASA Image and Video Library

1990-03-03

STS-36 Mission Specialist (MS) David C. Hilmers points the large-format AEROLINHOF camera out overhead window W7 on the aft flight deck of Atlantis, Orbiter Vehicle (OV) 104. Hilmers records Earth imagery using the camera. Hilmers and four other astronauts spent four days, 10 hours and 19 minutes aboard OV-104 for the Department of Defense (DOD) devoted mission.

The Virtual Consortium: Tim Bucknall Describes How a Group of Carolina Libraries Came Together to Expand Dramatically Their Journal Content

ERIC Educational Resources Information Center

Bucknall, Tim

2005-01-01

The Carolina Consortium came into being for one purpose: to conclude deals that would allow the sharing of both the costs and the content of a large number of academic journals from three major publishers--Wiley, Springer, and Blackwell. In just a few months--and without any central authority, funding, or administrative overhead--librarians from…

Overhead Costs and Rates in the U.S. Defense Industrial Base. Volume 1

DTIC Science & Technology

1980-10-01

Manager rather than to establish rigidly defined cost accounting structures. The conclusions to be own from the analysis were that overhead costs have...specific costs which make up tho overhead account ; whether management is controlling them; whether these costs are "reasonable" and the external factors... cost accounting structures, . ..... ....... .... ... ............................... , , ,’" ’ .. -17- and since there is no one accounting definition of

75 FR 31803 - Notice of Issuance of Final Determination Concerning a Lift Unit for an Overhead Patient Lift System

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-04

... Determination Concerning a Lift Unit for an Overhead Patient Lift System AGENCY: U.S. Customs and Border... concerning the country of origin of a lift unit for an overhead patient lift system. Based upon the facts presented, CBP has concluded in the final determination that Sweden is the country of origin of the lift...

The Use of Probability Theory as a Basis for Planning and Controlling Overhead Costs in Education and Industry. Final Report.

ERIC Educational Resources Information Center

Vinson, R. B.

In this report, the author suggests changes in the treatment of overhead costs by hypothesizing that "the effectiveness of standard costing in planning and controlling overhead costs can be increased through the use of probability theory and associated statistical techniques." To test the hypothesis, the author (1) presents an overview of the…

A Sensor Middleware for integration of heterogeneous medical devices.

PubMed

Brito, M; Vale, L; Carvalho, P; Henriques, J

2010-01-01

In this paper, the architecture of a modular, service-oriented, Sensor Middleware for data acquisition and processing is presented. The described solution was developed with the purpose of solving two increasingly relevant problems in the context of modern pHealth systems: i) to aggregate a number of heterogeneous, off-the-shelf, devices from which clinical measurements can be acquired and ii) to provide access and integration with an 802.15.4 network of wearable sensors. The modular nature of the Middleware provides the means to easily integrate pre-processing algorithms into processing pipelines, as well as new drivers for adding support for new sensor devices or communication technologies. Tests performed with both real and artificially generated data streams show that the presented solution is suitable for use both in a Windows PC or a Windows Mobile PDA with minimal overhead.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rizzi, Silvio; Hereld, Mark; Insley, Joseph

In this work we perform in-situ visualization of molecular dynamics simulations, which can help scientists to visualize simulation output on-the-fly, without incurring storage overheads. We present a case study to couple LAMMPS, the large-scale molecular dynamics simulation code with vl3, our parallel framework for large-scale visualization and analysis. Our motivation is to identify effective approaches for covisualization and exploration of large-scale atomistic simulations at interactive frame rates.We propose a system of coupled libraries and describe its architecture, with an implementation that runs on GPU-based clusters. We present the results of strong and weak scalability experiments, as well as future researchmore » avenues based on our results.« less

A computer program to perform dynamic thermal analysis for bare overhead conductors during short-time overload conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shrestha, P.; Pham, K.

1995-12-31

Under emergency conditions, a bare overhead conductor can carry an increased amount of current that is well in excess of its normal rating. When there is this increase in current flow on a bare overhead conductor, the temperature does not rise instantaneously. but increases along a curve determined by the current, the conductor properties and the ambient conditions. The conductor temperature at the end of a short-time overload period must be restricted to its maximum design value. This paper presents a simplified approach in analyzing the dynamic performance for bare overhead conductors during short-time overload condition. A computer program wasmore » developed to calculate the short-time ratings for bare overhead conductors. The following parameters: current induced heating. solar load, convective/conductive cooling, radiative cooling, altitude, wind velocity and ampacity of the bare conductor were considered. Several sample graphical output lots are included with the paper.« less

Ergonomic evaluation of a wearable assistive device for overhead work.

PubMed

Rashedi, Ehsan; Kim, Sunwook; Nussbaum, Maury A; Agnew, Michael J

2014-01-01

Overhead work is an important risk factor for upper extremity (UE) musculoskeletal disorders. We examined the potential of a mechanical arm and an exoskeletal vest as a wearable assistive device (WADE) for overhead work. Twelve participants completed 10 minutes of simulated, intermittent overhead work, using each of three payloads (1.1, 3.4 and 8.1 kg) and with/without the WADE. Ratings of perceived discomfort (RPDs) and electromyography (EMG) were obtained for the upper arms, shoulders and low back. Using the WADE, UE RPDs decreased by ∼50% with the heavier payloads, whereas smaller (∼25%) and non-significant increases in low-back RPDs were found and were relatively independent of payload. Changes in RPDs with WADE use were consistent with physical demands indicated by EMG, though EMG-based differences in fatigue were less apparent. Participants generally preferred using the WADE, particularly with heavier payloads. These results supported the potential utility of a WADE as an intervention for overhead work.

Environmental Assessment for QSEU116038 - Lower Pattern Altitude at Moody Air Force Base, Georgia

DTIC Science & Technology

2012-04-01

flight rules ( IFR ) overhead flight patterns. The 2,000-foot AGL VFR overhead flight pattern is associated with the previous Moody AFB training mission...EA Environmental Assessment EIS environmental impact statement IFR instrument flight rules Lmax maximum sound level NEPA National Environmental...airspace only (airspace immediately surrounding the Moody AFB airfield) and would not affect instrument flight rules ( IFR ) overhead flight patterns

Calculation of induced voltages on overhead lines caused by inclined lightning strokes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakakibara, A.

1989-01-01

Equations to calculate the inducing scalar and vector potentials produced by inclined return strokes are shown. Equations are also shown for calculating the induced voltages on overhead lines where horizontal components of inducing vector potential exist. The adequacy of the calculation method is demonstrated by field experiments. Using these equations, induced voltages on overhead lines are calculated for a variety of directions of return strokes.

Overhead drilling: Comparing three bases for aligning a drilling jig to vertical

PubMed Central

Rempel, David; Star, Demetra; Barr, Alan; Janowitz, Ira

2010-01-01

Problem Drilling overhead into concrete or metal ceilings is a strenuous task done by construction workers to hang ductwork, piping, and electrical equipment. The task is associated with upper body pain and musculoskeletal disorders. Previously, we described a field usability evaluation of a foot lever and inverted drill press intervention devices that were compared to the usual method for overhead drilling. Both interventions were rated as inferior to the usual method based on poor setup time and mobility. Method Three new interventions, which differed on the design used for aligning the drilling column to vertical, were compared to the usual method for overhead drilling by commercial construction workers (n=16). Results The usual method was associated with the highest levels of regional body fatigue and the poorest usability ratings when compared to the three interventions. Conclusion Overall, the ‘Collar Base’ intervention design received the best usability ratings. Impact on Industry Intervention designs developed for overhead drilling may reduce shoulder fatigue and prevent subsequent musculoskeletal disorders. These designs may also be useful for other overhead work such as lifting and supporting materials (e.g., piping, ducts) that are installed near the ceiling. Workplace health and safety interventions may require multiple rounds of field-testing prior to achieving acceptable usability ratings by the end users. PMID:20630276

Knowledge management: An abstraction of knowledge base and database management systems

NASA Technical Reports Server (NTRS)

Riedesel, Joel D.

1990-01-01

Artificial intelligence application requirements demand powerful representation capabilities as well as efficiency for real-time domains. Many tools exist, the most prevalent being expert systems tools such as ART, KEE, OPS5, and CLIPS. Other tools just emerging from the research environment are truth maintenance systems for representing non-monotonic knowledge, constraint systems, object oriented programming, and qualitative reasoning. Unfortunately, as many knowledge engineers have experienced, simply applying a tool to an application requires a large amount of effort to bend the application to fit. Much work goes into supporting work to make the tool integrate effectively. A Knowledge Management Design System (KNOMAD), is described which is a collection of tools built in layers. The layered architecture provides two major benefits; the ability to flexibly apply only those tools that are necessary for an application, and the ability to keep overhead, and thus inefficiency, to a minimum. KNOMAD is designed to manage many knowledge bases in a distributed environment providing maximum flexibility and expressivity to the knowledge engineer while also providing support for efficiency.

ESS-FH: Enhanced Security Scheme for Fast Handover in Hierarchical Mobile IPv6

NASA Astrophysics Data System (ADS)

You, Ilsun; Lee, Jong-Hyouk; Sakurai, Kouichi; Hori, Yoshiaki

Fast Handover for Hierarchical Mobile IPv6 (F-HMIPv6) that combines advantages of Fast Handover for Mobile IPv6 (FMIPv6) and Hierarchical Mobile IPv6 (HMIPv6) achieves the superior performance in terms of handover latency and signaling overhead compared with previously developed mobility protocols. However, without being secured, F-HMIPv6 is vulnerable to various security threats. In 2007, Kang and Park proposed a security scheme, which is seamlessly integrated into F-HMIPv6. In this paper, we reveal that Kang-Park's scheme cannot defend against the Denial of Service (DoS) and redirect attacks while largely relying on the group key. Then, we propose an Enhanced Security Scheme for F-HMIPv6 (ESS-FH) that achieves the strong key exchange and the key independence as well as addresses the weaknesses of Kang-Park's scheme. More importantly, it enables fast handover between different MAP domains. The proposed scheme is formally verified based on BAN-logic, and its handover latency is analyzed and compared with that of Kang-Park's scheme.

High Fidelity Simulations of Large-Scale Wireless Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onunkwo, Uzoma; Benz, Zachary

The worldwide proliferation of wireless connected devices continues to accelerate. There are 10s of billions of wireless links across the planet with an additional explosion of new wireless usage anticipated as the Internet of Things develops. Wireless technologies do not only provide convenience for mobile applications, but are also extremely cost-effective to deploy. Thus, this trend towards wireless connectivity will only continue and Sandia must develop the necessary simulation technology to proactively analyze the associated emerging vulnerabilities. Wireless networks are marked by mobility and proximity-based connectivity. The de facto standard for exploratory studies of wireless networks is discrete event simulationsmore » (DES). However, the simulation of large-scale wireless networks is extremely difficult due to prohibitively large turnaround time. A path forward is to expedite simulations with parallel discrete event simulation (PDES) techniques. The mobility and distance-based connectivity associated with wireless simulations, however, typically doom PDES and fail to scale (e.g., OPNET and ns-3 simulators). We propose a PDES-based tool aimed at reducing the communication overhead between processors. The proposed solution will use light-weight processes to dynamically distribute computation workload while mitigating communication overhead associated with synchronizations. This work is vital to the analytics and validation capabilities of simulation and emulation at Sandia. We have years of experience in Sandia’s simulation and emulation projects (e.g., MINIMEGA and FIREWHEEL). Sandia’s current highly-regarded capabilities in large-scale emulations have focused on wired networks, where two assumptions prevent scalable wireless studies: (a) the connections between objects are mostly static and (b) the nodes have fixed locations.« less

Overhead Projector Demonstrations.

ERIC Educational Resources Information Center

Kolb, Doris, Ed.

1987-01-01

Describes several chemistry demonstrations that use an overhead projector. Some of the demonstrations deal with electrochemistry, and another deals with the reactions of nonvolatile immiscible liquid in water. (TW)

Variance analysis refines overhead cost control.

PubMed

Cooper, J C; Suver, J D

1992-02-01

Many healthcare organizations may not fully realize the benefits of standard cost accounting techniques because they fail to routinely report volume variances in their internal reports. If overhead allocation is routinely reported on internal reports, managers can determine whether billing remains current or lost charges occur. Healthcare organizations' use of standard costing techniques can lead to more realistic performance measurements and information system improvements that alert management to losses from unrecovered overhead in time for corrective action.

Exploring versioned distributed arrays for resilience in scientific applications: Global view resilience

DOE PAGES

Chien, Andrew A.; Balaji, Pavan; Dun, Nan; ...

2016-09-08

Exascale studies project reliability challenges for future HPC systems. We present the Global View Resilience (GVR) system, a library for portable resilience. GVR begins with a subset of the Global Arrays interface, and adds new capabilities to create versions, name versions, and compute on version data. Applications can focus versioning where and when it is most productive, and customize for each application structure independently. This control is portable, and its embedding in application source makes it natural to express and easy to maintain. The ability to name multiple versions and “partially materialize” them efficiently makes ambitious forward-recovery based on “datamore » slices” across versions or data structures both easy to express and efficient. Using several large applications (OpenMC, preconditioned conjugate gradient (PCG) solver, ddcMD, and Chombo), we evaluate the programming effort to add resilience. The required changes are small (< 2% lines of code (LOC)), localized and machine-independent, and perhaps most important, require no software architecture changes. We also measure the overhead of adding GVR versioning and show that overheads < 2% are generally achieved. This overhead suggests that GVR can be implemented in large-scale codes and support portable error recovery with modest investment and runtime impact. Our results are drawn from both IBM BG/Q and Cray XC30 experiments, demonstrating portability. We also present two case studies of flexible error recovery, illustrating how GVR can be used for multi-version rollback recovery, and several different forward-recovery schemes. GVR’s multi-version enables applications to survive latent errors (silent data corruption) with significant detection latency, and forward recovery can make that recovery extremely efficient. Lastly, our results suggest that GVR is scalable, portable, and efficient. GVR interfaces are flexible, supporting a variety of recovery schemes, and altogether GVR embodies a gentle-slope path to tolerate growing error rates in future extreme-scale systems.« less

Exploring versioned distributed arrays for resilience in scientific applications: Global view resilience

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chien, Andrew A.; Balaji, Pavan; Dun, Nan

Exascale studies project reliability challenges for future HPC systems. We present the Global View Resilience (GVR) system, a library for portable resilience. GVR begins with a subset of the Global Arrays interface, and adds new capabilities to create versions, name versions, and compute on version data. Applications can focus versioning where and when it is most productive, and customize for each application structure independently. This control is portable, and its embedding in application source makes it natural to express and easy to maintain. The ability to name multiple versions and “partially materialize” them efficiently makes ambitious forward-recovery based on “datamore » slices” across versions or data structures both easy to express and efficient. Using several large applications (OpenMC, preconditioned conjugate gradient (PCG) solver, ddcMD, and Chombo), we evaluate the programming effort to add resilience. The required changes are small (< 2% lines of code (LOC)), localized and machine-independent, and perhaps most important, require no software architecture changes. We also measure the overhead of adding GVR versioning and show that overheads < 2% are generally achieved. This overhead suggests that GVR can be implemented in large-scale codes and support portable error recovery with modest investment and runtime impact. Our results are drawn from both IBM BG/Q and Cray XC30 experiments, demonstrating portability. We also present two case studies of flexible error recovery, illustrating how GVR can be used for multi-version rollback recovery, and several different forward-recovery schemes. GVR’s multi-version enables applications to survive latent errors (silent data corruption) with significant detection latency, and forward recovery can make that recovery extremely efficient. Lastly, our results suggest that GVR is scalable, portable, and efficient. GVR interfaces are flexible, supporting a variety of recovery schemes, and altogether GVR embodies a gentle-slope path to tolerate growing error rates in future extreme-scale systems.« less

Clinical concepts for treatment of the elbow in the adolescent overhead athlete.

PubMed

Ellenbecker, Todd S; Reinold, Michael; Nelson, Cory O

2010-10-01

Injuries to the adolescent elbow are common because of the repetitive overuse inherent in many overhead sport activities. The management of these patients is greatly facilitated through a greater understanding of the demands placed on the upper extremity kinetic chain during these overhead activities as well as a detailed examination and rehabilitation for the entire upper extremity kinetic chain. Particular emphasis on improving rotator cuff strength and muscular endurance, along with scapular stabilization, is a critical part of elbow rehabilitation in these patients. In addition, the use of a strategic and progressive interval sport return program is necessary to minimize reinjury and return the adolescent overhead athlete to full function. Copyright © 2010 Elsevier Inc. All rights reserved.

ISIM Lowered into Thermal Vacuum Chamber

NASA Image and Video Library

2017-12-08

An overhead glimpse inside the thermal vacuum chamber at NASA's Goddard Space Flight Center in Greenbelt, Md., as engineers ready the James Webb Space Telescope's Integrated Science Instrument Module, just lowered into the chamber for its first thermal vacuum test. The ISIM and the ISIM System Integration Fixture that holds the ISIM Electronics Compartment is completely covered in protective blankets to shield it from contamination. Image credit: NASA/Chris Gunn NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Integrated analysis of error detection and recovery

NASA Technical Reports Server (NTRS)

Shin, K. G.; Lee, Y. H.

1985-01-01

An integrated modeling and analysis of error detection and recovery is presented. When fault latency and/or error latency exist, the system may suffer from multiple faults or error propagations which seriously deteriorate the fault-tolerant capability. Several detection models that enable analysis of the effect of detection mechanisms on the subsequent error handling operations and the overall system reliability were developed. Following detection of the faulty unit and reconfiguration of the system, the contaminated processes or tasks have to be recovered. The strategies of error recovery employed depend on the detection mechanisms and the available redundancy. Several recovery methods including the rollback recovery are considered. The recovery overhead is evaluated as an index of the capabilities of the detection and reconfiguration mechanisms.

Integrated billing and accounts receivable management system needed to maximize payments and cope with managed care.

PubMed

Sanders, J; Wold, D; Sullivan, T

1999-01-01

The billing and accounts receivable management process in medical practices today has evolved into a multidisciplinary function. This function requires efficient, coordinated performance by physicians and all staff members, from the point of initial patient contact through aggressive follow-up on delinquent payments for services rendered. Offices with deficient or nonexistent billing and accounts receivable management systems typically experience collection ratios that are less than industry norms. They also experience poor cash flow and unnecessary overhead costs. To avoid costly inefficiencies and ensure that it maximizes payments from third-party payors and patients, a medical practice must have an integrated billing and accounts receivable management system that includes components outlined in this article.

KSC-01pp0245

NASA Image and Video Library

2001-02-03

Workers in the Space Station Processing Facility attach an overhead crane to the Multi-Purpose Logistics Module Donatello to lift it out of the shipping container. In the SSPF, Donatello will undergo processing by the payload test team, including integrated electrical tests with other Station elements in the SSPF, leak tests, electrical and software compatibility tests with the Space Shuttle (using the Cargo Integrated Test equipment) and an Interface Verification Test once the module is installed in the Space Shuttle’s payload bay at the launch pad. The most significant mechanical task to be performed on Donatello in the SSPF is the installation and outfitting of the racks for carrying the various experiments and cargo. Donatello will be launched on mission STS-130, currently planned for September 2004

KSC-01pp0246

NASA Image and Video Library

2001-02-03

In the Space Station Processing Facility, workers help guide the overhead crane as it lifts the Multi-Purpose Logistics Module Donatello out of the shipping container. In the SSPF, Donatello will undergo processing by the payload test team, including integrated electrical tests with other Station elements in the SSPF, leak tests, electrical and software compatibility tests with the Space Shuttle (using the Cargo Integrated Test equipment) and an Interface Verification Test once the module is installed in the Space Shuttle’s payload bay at the launch pad. The most significant mechanical task to be performed on Donatello in the SSPF is the installation and outfitting of the racks for carrying the various experiments and cargo. Donatello will be launched on mission STS-130, currently planned for September 2004

KSC-01pp0248

NASA Image and Video Library

2001-02-03

In the Space Station Processing Facility, workers wait for the Multi-Purpose Logistics Module Donatello, suspended by an overhead crane, to move onto a workstand. In the SSPF, Donatello will undergo processing by the payload test team, including integrated electrical tests with other Station elements in the SSPF, leak tests, electrical and software compatibility tests with the Space Shuttle (using the Cargo Integrated Test equipment) and an Interface Verification Test once the module is installed in the Space Shuttle’s payload bay at the launch pad. The most significant mechanical task to be performed on Donatello in the SSPF is the installation and outfitting of the racks for carrying the various experiments and cargo. Donatello will be launched on mission STS-130, currently planned for September 2004

Effect of an overhead shield on gamma-ray skyshine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stedry, M.H.; Shultis, J.K.; Faw, R.E.

1996-06-01

A hybrid Monte Carlo and integral line-beam method is used to determine the effect of a horizontal slab shield above a gamma-ray source on the resulting skyshine doses. A simplified Monte Carlo procedure is used to determine the energy and angular distribution of photons escaping the source shield into the atmosphere. The escaping photons are then treated as a bare, point, skyshine source, and the integral line-beam method is used to estimate the skyshine dose at various distances from the source. From results for arbitrarily collimated and shielded sources, the skyshine dose is found to depend primarily on the mean-free-pathmore » thickness of the shield and only very weakly on the shield material.« less

Reliable WDM multicast in optical burst-switched networks

NASA Astrophysics Data System (ADS)

Jeong, Myoungki; Qiao, Chunming; Xiong, Yijun

2000-09-01

IN this paper,l we present a reliable WDM (Wavelength-Division Multiplexing) multicast protocol in optical burst-switched (OBS) networks. Since the burst dropping (loss) probability may be potentially high in a heavily loaded OBS backbone network, reliable multicast protocols that have developed for IP networks at the transport (or application) layer may incur heavy overheads such as a large number of duplicate retransmissions. In addition, it may take a longer time for an end host to detect and then recover from burst dropping (loss) occurred at the WDM layer. For efficiency reasons, we propose burst loss recovery within the OBS backbone (i.e., at the WDM link layer). The proposed protocol requires two additional functions to be performed by the WDM switch controller: subcasting and maintaining burst states, when the WDM switch has more than one downstream on the WDM multicast tree. We show that these additional functions are simple to implement and the overhead associated with them is manageable.

Atmospheric opacity in the Schumann-Runge bands and the aeronomic dissociation of water vapor

NASA Technical Reports Server (NTRS)

Frederick, J. E.; Hudson, R. D.

1980-01-01

Knowledge of the aeronomic production of odd hydrogen in the dissociation of water vapor is limited by uncertainties in the penetration of solar irradiance in the Schumann-Runge bands of O2 and by incomplete information concerning the products of photolysis at Lyman alpha. Consideration of all error sources involved in computing the H2O dissociation rate in the wavelength region 175-200 nm leads to an estimated uncertainty of plus or minus 35% at an altitude of 90 km for an overhead sun. The uncertainty increases with decreasing altitude such that the true dissociation rate at 60 km for an overhead sun lies between 0.45 and 1.55 times the results computed using the best input parameters currently available. Calculations of the H2O dissociation rate by Lyman alpha should include the variation in O2 opacity across the solar line width. Neglect of this can lead to errors as large as 50% at altitudes where the process is the major source of odd hydrogen.

The use of the liquid crystal display (LCD) panel as a teaching aid in medical lectures.

PubMed

Wong, K T

1992-01-01

The liquid crystal display (LCD) panel is designed to project on-screen information of a microcomputer onto a larger screen with the aid of a standard overhead projector, so that large audiences may view on-screen information without having to crowd around the TV monitor. As little has been written about its use as a visual aid in medical teaching, the present report documents its use in a series of pathology lectures delivered, over a 2-year period, to two classes of about 150 medical students each. Some advantages of the LCD panel over the 35mm slide include the flexibility of last-minute text changes and less lead time needed for text preparation. It eliminates the problems of messy last-minute changes in, and improves legibility of, handwritten overhead projector transparencies. The disadvantages of using an LCD panel include the relatively bulky equipment which may pose transport problems, image clarity that is inferior to the 35mm slide, and equipment costs.

A Holistic Management Architecture for Large-Scale Adaptive Networks

DTIC Science & Technology

2007-09-01

transmission and processing overhead required for management. The challenges of building models to describe dynamic systems are well-known to the field of...increases the challenge of finding a simple approach to assessing the state of the network. Moreover, the performance state of one network link may be... challenging . These obstacles indicate the need for a less comprehensive-analytical, more systemic-holistic approach to managing networks. This approach might

SMAC: A soft MAC to reduce control overhead and latency in CDMA-based AMI networks

DOE PAGES

Garlapati, Shravan; Kuruganti, Teja; Buehrer, Michael R.; ...

2015-10-26

The utilization of state-of-the-art 3G cellular CDMA technologies in a utility owned AMI network results in a large amount of control traffic relative to data traffic, increases the average packet delay and hence are not an appropriate choice for smart grid distribution applications. Like the CDG, we consider a utility owned cellular like CDMA network for smart grid distribution applications and classify the distribution smart grid data as scheduled data and random data. Also, we propose SMAC protocol, which changes its mode of operation based on the type of the data being collected to reduce the data collection latency andmore » control overhead when compared to 3G cellular CDMA2000 MAC. The reduction in the data collection latency and control overhead aids in increasing the number of smart meters served by a base station within the periodic data collection interval, which further reduces the number of base stations needed by a utility or reduces the bandwidth needed to collect data from all the smart meters. The reduction in the number of base stations and/or the reduction in the data transmission bandwidth reduces the CAPital EXpenditure (CAPEX) and OPerational EXpenditure (OPEX) of the AMI network. Finally, the proposed SMAC protocol is analyzed using markov chain, analytical expressions for average throughput and average packet delay are derived, and simulation results are also provided to verify the analysis.« less

Increased knee valgus alignment and moment during single-leg landing after overhead stroke as a potential risk factor of anterior cruciate ligament injury in badminton.

PubMed

Kimura, Yuka; Ishibashi, Yasuyuki; Tsuda, Eiichi; Yamamoto, Yuji; Hayashi, Yoshimitsu; Sato, Shuichi

2012-03-01

In badminton, knees opposite to the racket-hand side received anterior cruciate ligament (ACL) injuries during single-leg landing after overhead stroke. Most of them occurred in the backhand-side of the rear court. Comparing lower limb biomechanics during single-leg landing after overhead stroke between the forehand-side and backhand-side court may help explain the different injury rates depending on court position. The knee kinematics and kinetics during single-leg landing after overhead stroke following back-stepping were different between the forehand-side and backhand-side court. Controlled laboratory study. Hip, knee and ankle joint kinematic and knee kinetic data were collected for 17 right-handed female college badminton players using a 3-dimensional motion analysis system. Subjects performed single-left-legged landing after an overhead stroke following left and right back-stepping. The kinematic and kinetic data of the left lower extremities during landing were measured and compared between left and right back-steps. Hip flexion and abduction and knee valgus at the initial contact, hip and knee flexion and knee valgus at the maximum knee flexion and the maximum knee valgus moment were significantly larger for the left back-step than the right back-step (p<0.05). Significant differences in joint kinematics and kinetics of the lower extremity during single-leg landing after overhead stroke were observed between different back-step directions. Increased knee valgus angle and moment following back-stepping to the backhand-side might be related to the higher incidence of ACL injury during single-leg landing after overhead stroke.

STS-98 U.S. Lab payload is moved to stand for weight determination

NASA Technical Reports Server (NTRS)

2000-01-01

KENNEDY SPACE CENTER, Fla. -- The U.S. Laboratory Destiny travels past the Multi-Purpose Logistics Module Leonardo in its overhead passage down the Space Station Processing Facility. The lab is being moved to the Launch Package Integration Stand (LPIS) for a weight and center of gravity determination. Destiny is the payload aboard Space Shuttle Atlantis on mission STS-98 to the Space Station. The lab is fitted with five system racks and will already have experiments installed inside for the flight. The launch is scheduled for January 2001.

Novel technology for enhanced security and trust in communication networks

NASA Astrophysics Data System (ADS)

Milovanov, Alexander; Bukshpun, Leonid; Pradhan, Ranjit; Jannson, Tomasz

2011-06-01

A novel technology that significantly enhances security and trust in wireless and wired communication networks has been developed. It is based on integration of a novel encryption mechanism and novel data packet structure with enhanced security tools. This novel data packet structure results in an unprecedented level of security and trust, while at the same time reducing power consumption and computing/communication overhead in networks. As a result, networks are provided with protection against intrusion, exploitation, and cyber attacks and posses self-building, self-awareness, self-configuring, self-healing, and self-protecting intelligence.

KSC-08pd2357

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – In the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center, an overhead crane lowers the Fine Guidance Sensor Scientific Instrument Protective Enclosure, or FSIPE, cover alongside the Orbital Replacement Unit Carrier, or ORUC, for installation. The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125. Launch is targeted for Oct. 8. PHoto credit: NASA/Jack Pfaller

Sensor Fusion for Nuclear Proliferation Activity Monitoring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adel Ghanem, Ph D

2007-03-30

The objective of Phase 1 of this STTR project is to demonstrate a Proof-of-Concept (PoC) of the Geo-Rad system that integrates a location-aware SmartTag (made by ZonTrak) and a radiation detector (developed by LLNL). It also includes the ability to transmit the collected radiation data and location information to the ZonTrak server (ZonService). The collected data is further transmitted to a central server at LLNL (the Fusion Server) to be processed in conjunction with overhead imagery to generate location estimates of nuclear proliferation and radiation sources.

KSC-01pp1386

NASA Image and Video Library

2001-07-23

KENNEDY SPACE CENTER, Fla. -- An overhead crane in the Space Station Processing Facility lifts the Integrated Cargo Carrier from its workstand to move it to the payload canister. The ICC holds several payloads for mission STS-105, the Early Ammonia Servicer and two experiment containers. The ICC will join the Multi-Purpose Logistics Module Leonardo in the payload canister for transport to Launch Pad 39A where they will be placed in the payload bay of Space Shuttle Discovery. Launch of STS-105 is scheduled for 5:38 p.m. EDT Aug. 9

Design and Implementation of a Secure Modbus Protocol

NASA Astrophysics Data System (ADS)

Fovino, Igor Nai; Carcano, Andrea; Masera, Marcelo; Trombetta, Alberto

The interconnectivity of modern and legacy supervisory control and data acquisition (SCADA) systems with corporate networks and the Internet has significantly increased the threats to critical infrastructure assets. Meanwhile, traditional IT security solutions such as firewalls, intrusion detection systems and antivirus software are relatively ineffective against attacks that specifically target vulnerabilities in SCADA protocols. This paper describes a secure version of the Modbus SCADA protocol that incorporates integrity, authentication, non-repudiation and anti-replay mechanisms. Experimental results using a power plant testbed indicate that the augmented protocol provides good security functionality without significant overhead.

A Hierarchical and Distributed Approach for Mapping Large Applications to Heterogeneous Grids using Genetic Algorithms

NASA Technical Reports Server (NTRS)

Sanyal, Soumya; Jain, Amit; Das, Sajal K.; Biswas, Rupak

2003-01-01

In this paper, we propose a distributed approach for mapping a single large application to a heterogeneous grid environment. To minimize the execution time of the parallel application, we distribute the mapping overhead to the available nodes of the grid. This approach not only provides a fast mapping of tasks to resources but is also scalable. We adopt a hierarchical grid model and accomplish the job of mapping tasks to this topology using a scheduler tree. Results show that our three-phase algorithm provides high quality mappings, and is fast and scalable.

A case study: semantic integration of gene-disease associations for type 2 diabetes mellitus from literature and biomedical data resources.

PubMed

Rebholz-Schuhmann, Dietrich; Grabmüller, Christoph; Kavaliauskas, Silvestras; Croset, Samuel; Woollard, Peter; Backofen, Rolf; Filsell, Wendy; Clark, Dominic

2014-07-01

In the Semantic Enrichment of the Scientific Literature (SESL) project, researchers from academia and from life science and publishing companies collaborated in a pre-competitive way to integrate and share information for type 2 diabetes mellitus (T2DM) in adults. This case study exposes benefits from semantic interoperability after integrating the scientific literature with biomedical data resources, such as UniProt Knowledgebase (UniProtKB) and the Gene Expression Atlas (GXA). We annotated scientific documents in a standardized way, by applying public terminological resources for diseases and proteins, and other text-mining approaches. Eventually, we compared the genetic causes of T2DM across the data resources to demonstrate the benefits from the SESL triple store. Our solution enables publishers to distribute their content with little overhead into remote data infrastructures, such as into any Virtual Knowledge Broker. Copyright © 2013. Published by Elsevier Ltd.

Parallel program debugging with flowback analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Jongdeok.

1989-01-01

This thesis describes the design and implementation of an integrated debugging system for parallel programs running on shared memory multi-processors. The goal of the debugging system is to present to the programmer a graphical view of the dynamic program dependences while keeping the execution-time overhead low. The author first describes the use of flowback analysis to provide information on causal relationship between events in a programs' execution without re-executing the program for debugging. Execution time overhead is kept low by recording only a small amount of trace during a program's execution. He uses semantic analysis and a technique called incrementalmore » tracing to keep the time and space overhead low. As part of the semantic analysis, he uses a static program dependence graph structure that reduces the amount of work done at compile time and takes advantage of the dynamic information produced during execution time. The cornerstone of the incremental tracing concept is to generate a coarse trace during execution and fill incrementally, during the interactive portion of the debugging session, the gap between the information gathered in the coarse trace and the information needed to do the flowback analysis using the coarse trace. Then, he describes how to extend the flowback analysis to parallel programs. The flowback analysis can span process boundaries; i.e., the most recent modification to a shared variable might be traced to a different process than the one that contains the current reference. The static and dynamic program dependence graphs of the individual processes are tied together with synchronization and data dependence information to form complete graphs that represent the entire program.« less

MBus: An Ultra-Low Power Interconnect Bus for Next Generation Nanopower Systems

PubMed Central

Pannuto, Pat; Lee, Yoonmyung; Kuo, Ye-Sheng; Foo, ZhiYoong; Kempke, Benjamin; Kim, Gyouho; Dreslinski, Ronald G.; Blaauw, David; Dutta, Prabal

2015-01-01

As we show in this paper, I/O has become the limiting factor in scaling down size and power toward the goal of invisible computing. Achieving this goal will require composing optimized and specialized—yet reusable—components with an interconnect that permits tiny, ultra-low power systems. In contrast to today’s interconnects which are limited by power-hungry pull-ups or high-overhead chip-select lines, our approach provides a superset of common bus features but at lower power, with fixed area and pin count, using fully synthesizable logic, and with surprisingly low protocol overhead. We present MBus, a new 4-pin, 22.6 pJ/bit/chip chip-to-chip interconnect made of two “shoot-through” rings. MBus facilitates ultra-low power system operation by implementing automatic power-gating of each chip in the system, easing the integration of active, inactive, and activating circuits on a single die. In addition, we introduce a new bus primitive: power oblivious communication, which guarantees message reception regardless of the recipient’s power state when a message is sent. This disentangles power management from communication, greatly simplifying the creation of viable, modular, and heterogeneous systems that operate on the order of nanowatts. To evaluate the viability, power, performance, overhead, and scalability of our design, we build both hardware and software implementations of MBus and show its seamless operation across two FPGAs and twelve custom chips from three different semiconductor processes. A three-chip, 2.2 mm3 MBus system draws 8 nW of total system standby power and uses only 22.6 pJ/bit/chip for communication. This is the lowest power for any system bus with MBus’s feature set. PMID:26855555

Pattern-based integer sample motion search strategies in the context of HEVC

NASA Astrophysics Data System (ADS)

Maier, Georg; Bross, Benjamin; Grois, Dan; Marpe, Detlev; Schwarz, Heiko; Veltkamp, Remco C.; Wiegand, Thomas

2015-09-01

The H.265/MPEG-H High Efficiency Video Coding (HEVC) standard provides a significant increase in coding efficiency compared to its predecessor, the H.264/MPEG-4 Advanced Video Coding (AVC) standard, which however comes at the cost of a high computational burden for a compliant encoder. Motion estimation (ME), which is a part of the inter-picture prediction process, typically consumes a high amount of computational resources, while significantly increasing the coding efficiency. In spite of the fact that both H.265/MPEG-H HEVC and H.264/MPEG-4 AVC standards allow processing motion information on a fractional sample level, the motion search algorithms based on the integer sample level remain to be an integral part of ME. In this paper, a flexible integer sample ME framework is proposed, thereby allowing to trade off significant reduction of ME computation time versus coding efficiency penalty in terms of bit rate overhead. As a result, through extensive experimentation, an integer sample ME algorithm that provides a good trade-off is derived, incorporating a combination and optimization of known predictive, pattern-based and early termination techniques. The proposed ME framework is implemented on a basis of the HEVC Test Model (HM) reference software, further being compared to the state-of-the-art fast search algorithm, which is a native part of HM. It is observed that for high resolution sequences, the integer sample ME process can be speed-up by factors varying from 3.2 to 7.6, resulting in the bit-rate overhead of 1.5% and 0.6% for Random Access (RA) and Low Delay P (LDP) configurations, respectively. In addition, the similar speed-up is observed for sequences with mainly Computer-Generated Imagery (CGI) content while trading off the bit rate overhead of up to 5.2%.

MBus: An Ultra-Low Power Interconnect Bus for Next Generation Nanopower Systems.

PubMed

Pannuto, Pat; Lee, Yoonmyung; Kuo, Ye-Sheng; Foo, ZhiYoong; Kempke, Benjamin; Kim, Gyouho; Dreslinski, Ronald G; Blaauw, David; Dutta, Prabal

2015-06-01

As we show in this paper, I/O has become the limiting factor in scaling down size and power toward the goal of invisible computing. Achieving this goal will require composing optimized and specialized-yet reusable-components with an interconnect that permits tiny, ultra-low power systems. In contrast to today's interconnects which are limited by power-hungry pull-ups or high-overhead chip-select lines, our approach provides a superset of common bus features but at lower power, with fixed area and pin count, using fully synthesizable logic, and with surprisingly low protocol overhead. We present MBus , a new 4-pin, 22.6 pJ/bit/chip chip-to-chip interconnect made of two "shoot-through" rings. MBus facilitates ultra-low power system operation by implementing automatic power-gating of each chip in the system, easing the integration of active, inactive, and activating circuits on a single die. In addition, we introduce a new bus primitive: power oblivious communication, which guarantees message reception regardless of the recipient's power state when a message is sent. This disentangles power management from communication, greatly simplifying the creation of viable, modular, and heterogeneous systems that operate on the order of nanowatts. To evaluate the viability, power, performance, overhead, and scalability of our design, we build both hardware and software implementations of MBus and show its seamless operation across two FPGAs and twelve custom chips from three different semiconductor processes. A three-chip, 2.2 mm 3 MBus system draws 8 nW of total system standby power and uses only 22.6 pJ/bit/chip for communication. This is the lowest power for any system bus with MBus's feature set.

Overhead Projector Demonstrations.

ERIC Educational Resources Information Center

Kolb, Doris, Ed.

1989-01-01

Described are demonstrations of the optical activity of two sugar solutions, and the effects of various substituents on acid strength using an overhead projector. Materials and procedures for each demonstration are discussed. (CW)

A Testing Platform for Validation of Overhead Conductor Aging Models and Understanding Thermal Limits

DOE Office of Scientific and Technical Information (OSTI.GOV)

Irminger, Philip; Starke, Michael R; Dimitrovski, Aleksandar D

2014-01-01

Power system equipment manufacturers and researchers continue to experiment with novel overhead electric conductor designs that support better conductor performance and address congestion issues. To address the technology gap in testing these novel designs, Oak Ridge National Laboratory constructed the Powerline Conductor Accelerated Testing (PCAT) facility to evaluate the performance of novel overhead conductors in an accelerated fashion in a field environment. Additionally, PCAT has the capability to test advanced sensors and measurement methods for accessing overhead conductor performance and condition. Equipped with extensive measurement and monitoring devices, PCAT provides a platform to improve/validate conductor computer models and assess themore » performance of novel conductors. The PCAT facility and its testing capabilities are described in this paper.« less

Computations on Wings With Full-Span Oscillating Control Surfaces Using Navier-Stokes Equations

NASA Technical Reports Server (NTRS)

Guruswamy, Guru P.

2013-01-01

A dual-level parallel procedure is presented for computing large databases to support aerospace vehicle design. This procedure has been developed as a single Unix script within the Parallel Batch Submission environment utilizing MPIexec and runs MPI based analysis software. It has been developed to provide a process for aerospace designers to generate data for large numbers of cases with the highest possible fidelity and reasonable wall clock time. A single job submission environment has been created to avoid keeping track of multiple jobs and the associated system administration overhead. The process has been demonstrated for computing large databases for the design of typical aerospace configurations, a launch vehicle and a rotorcraft.

A Novel Threshold Voltage Defined Multiplexer for Interconnect Camouflaging

DTIC Science & Technology

2017-03-01

camouflaged onventional reli amouflaged to i g the overhead random-net bas indicate 32-81 rhead when 5 the proposed te ing, Camouflag an Intellectua...profitable or of camouflag w chosen ga area, delay of adversary w rea overhead . nalities such ct gate funct l create a pa o through a gu gate...of l ; and only few ll overhead w proposed ca el RE-resistan defined switch aves no layou ouflaged, the a match the ou est pattern and ly; and (c

U.S. Army Corps of Engineers: Building Overhead Costs into Projects and Customers’ Views on Information Provided

DTIC Science & Technology

2013-06-01

U.S. ARMY CORPS OF ENGINEERS Building Overhead Costs into Projects and Customers ’ Views on Information Provided...Overhead Costs into Projects and Customers ’ Views on Information Provided 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S...and Customers ’ Views on Information Provided Why GAO Did This Study The Corps spends billions of dollars annually on projects in its Civil Works

High-performance parallel interface to synchronous optical network gateway

DOEpatents

St. John, Wallace B.; DuBois, David H.

1998-08-11

A digital system provides sending and receiving gateways for HIPPI interfaces. Electronic logic circuitry formats data signals and overhead signals in a data frame that is suitable for transmission over a connecting fiber optic link. Multiplexers route the data and overhead signals to a framer module. The framer module allocates the data and overhead signals to a plurality of 9-byte words that are arranged in a selected protocol. The formatted words are stored in a storage register for output through the gateway.

The thrower's elbow.

PubMed

Patel, Ronak M; Lynch, T Sean; Amin, Nirav H; Calabrese, Gary; Gryzlo, Stephen M; Schickendantz, Mark S

2014-07-01

Overhead throwing activities expose the elbow to tremendous valgus stress, making athletes vulnerable to a specific constellation of injuries. Although baseball players, in particular pitchers, are the athletes affected most commonly, overhead throwing athletes in football, volleyball, tennis, and javelin tossing also are affected. The purpose of this review is to review the anatomy, biomechanics, pathophysiology, and treatment of elbow disorders related to overhead throwing athletes. Although focus is on management of ulnar collateral ligament injuries, all common pathologies are discussed. Copyright © 2014 Elsevier Inc. All rights reserved.

Adding Data Management Services to Parallel File Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brandt, Scott

2015-03-04

The objective of this project, called DAMASC for “Data Management in Scientific Computing”, is to coalesce data management with parallel file system management to present a declarative interface to scientists for managing, querying, and analyzing extremely large data sets efficiently and predictably. Managing extremely large data sets is a key challenge of exascale computing. The overhead, energy, and cost of moving massive volumes of data demand designs where computation is close to storage. In current architectures, compute/analysis clusters access data in a physically separate parallel file system and largely leave it scientist to reduce data movement. Over the past decadesmore » the high-end computing community has adopted middleware with multiple layers of abstractions and specialized file formats such as NetCDF-4 and HDF5. These abstractions provide a limited set of high-level data processing functions, but have inherent functionality and performance limitations: middleware that provides access to the highly structured contents of scientific data files stored in the (unstructured) file systems can only optimize to the extent that file system interfaces permit; the highly structured formats of these files often impedes native file system performance optimizations. We are developing Damasc, an enhanced high-performance file system with native rich data management services. Damasc will enable efficient queries and updates over files stored in their native byte-stream format while retaining the inherent performance of file system data storage via declarative queries and updates over views of underlying files. Damasc has four key benefits for the development of data-intensive scientific code: (1) applications can use important data-management services, such as declarative queries, views, and provenance tracking, that are currently available only within database systems; (2) the use of these services becomes easier, as they are provided within a familiar file-based ecosystem; (3) common optimizations, e.g., indexing and caching, are readily supported across several file formats, avoiding effort duplication; and (4) performance improves significantly, as data processing is integrated more tightly with data storage. Our key contributions are: SciHadoop which explores changes to MapReduce assumption by taking advantage of semantics of structured data while preserving MapReduce’s failure and resource management; DataMods which extends common abstractions of parallel file systems so they become programmable such that they can be extended to natively support a variety of data models and can be hooked into emerging distributed runtimes such as Stanford’s Legion; and Miso which combines Hadoop and relational data warehousing to minimize time to insight, taking into account the overhead of ingesting data into data warehousing.« less

Arthroscopic capsular plication for microtraumatic anterior shoulder instability in overhead athletes.

PubMed

Jones, Kristofer J; Kahlenberg, Cynthia A; Dodson, Christopher C; Nam, Denis; Williams, Riley J; Altchek, David W

2012-09-01

Extreme loading conditions at the glenohumeral joint during overhead athletic activities can result in both soft tissue and osseous adaptative changes at the shoulder. Subtle alterations in the stabilizing structures may lead to anterior instability and debilitating shoulder pain with subsequent inability to participate in athletics. There is currently a paucity of data documenting clinical outcomes after arthroscopic capsular plication in overhead athletes who demonstrate objective findings of pain and anterior instability on physical examination. To evaluate outcomes after arthroscopic capsular plication for anterior instability in overhead athletes with an emphasis on postoperative range of motion, postoperative shoulder function, and return to sport. Case series; Level of evidence, 4. The authors identified 20 overhead athletes with debilitating shoulder pain and a failed trial of nonoperative management who underwent arthroscopic capsular plication (12 suture plication, 8 suture anchor plication) for anterior instability related to isolated capsular redundancy. Patients were evaluated with the Single Assessment Numerical Evaluation (SANE) and Kerlan-Jobe Orthopaedic Clinic (KJOC) Shoulder and Elbow Score, and they were interviewed to determine the rate of return to athletic activity. Failures of treatment included patients who demonstrated debilitating pain that precluded return to sport. At a mean follow-up of 3.6 years (range, 2.0-5.5 years), 18 (90%) patients returned to overhead sports, with 17 (85%) at their preinjury level. The mean (SD) SANE score was 86 (17.5%; range, 30%-100%), and the mean (SD) KJOC score was 82 (18.2; range, 28-100). When compared with the contralateral extremity, there were no significant differences in glenohumeral range of motion. Two patients with associated rotator cuff injury experienced persistent pain with overhead activity and were unable to return to sport, representing a 10% failure rate. Arthroscopic capsular plication for anterior instability related to isolated capsular redundancy is an effective procedure that yields a high rate of patient satisfaction and return to overhead athletic activity with an acceptably low failure rate. Patients with associated rotator cuff injury may be at higher risk for treatment failure.

Overhead Allocation and Incentives for Cost Minimization in Defense Procurement

DTIC Science & Technology

1992-01-01

Staff. The publication should be of interest to researchers and policymakers who are concerned about the effects of profit policy and cost - account ...ing regulations on business incentives, system costs , and contractor profits. A shorter version of this report has appeared in The Accounting Re- view... Accounting Review. ii SUMMARY Defense firms typically produce a large number of products and it is often difficult to keep track of the cost of producing

10. 4TH FLOOR, HOTEL SOAP LINE No. 6 TO SOUTHWEST, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. 4TH FLOOR, HOTEL SOAP LINE No. 6 TO SOUTHWEST, WITH AUTOMATIC CUTTER (LEFT), PRESS (CENTER), AND WRAPPER (RIGHT); LARGE CHUTE AT CENTER FROM 5TH FLOOR BINS TO 3RD FLOOR SOAP MILLS; OVERHEAD AND FLOOR (LOWER RIGHT) FINISHED GOODS CONVEYORS TO G BLOCK (HAER NO. NJ-71-NN) - Colgate & Company Jersey City Plant, Building No. B-14, 54-58 Grand Street, Jersey City, Hudson County, NJ

Southeast corner with overhead crane in foreground Bureau of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Southeast corner with overhead crane in foreground - Bureau of Mines Boulder City Experimental Station, Titanium Development Plant, Date Street north of U.S. Highway 93, Boulder City, Clark County, NV

Overhead Projector Demonstrations.

ERIC Educational Resources Information Center

Kolb, Doris, Ed.

1989-01-01

Included are demonstrations using the overhead projector to show change in optical rotation with wavelength and aromatic pi cloud availability, and formation of colored charge-transfer complexes. Instructional techniques unique to these topics are discussed. (CW)

Extending Moore's Law via Computationally Error Tolerant Computing.

DOE PAGES

Deng, Bobin; Srikanth, Sriseshan; Hein, Eric R.; ...

2018-03-01

Dennard scaling has ended. Lowering the voltage supply (V dd) to sub-volt levels causes intermittent losses in signal integrity, rendering further scaling (down) no longer acceptable as a means to lower the power required by a processor core. However, it is possible to correct the occasional errors caused due to lower V dd in an efficient manner and effectively lower power. By deploying the right amount and kind of redundancy, we can strike a balance between overhead incurred in achieving reliability and energy savings realized by permitting lower V dd. One promising approach is the Redundant Residue Number System (RRNS)more » representation. Unlike other error correcting codes, RRNS has the important property of being closed under addition, subtraction and multiplication, thus enabling computational error correction at a fraction of an overhead compared to conventional approaches. We use the RRNS scheme to design a Computationally-Redundant, Energy-Efficient core, including the microarchitecture, Instruction Set Architecture (ISA) and RRNS centered algorithms. Finally, from the simulation results, this RRNS system can reduce the energy-delay-product by about 3× for multiplication intensive workloads and by about 2× in general, when compared to a non-error-correcting binary core.« less

Extending Moore's Law via Computationally Error Tolerant Computing.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Bobin; Srikanth, Sriseshan; Hein, Eric R.

Dennard scaling has ended. Lowering the voltage supply (V dd) to sub-volt levels causes intermittent losses in signal integrity, rendering further scaling (down) no longer acceptable as a means to lower the power required by a processor core. However, it is possible to correct the occasional errors caused due to lower V dd in an efficient manner and effectively lower power. By deploying the right amount and kind of redundancy, we can strike a balance between overhead incurred in achieving reliability and energy savings realized by permitting lower V dd. One promising approach is the Redundant Residue Number System (RRNS)more » representation. Unlike other error correcting codes, RRNS has the important property of being closed under addition, subtraction and multiplication, thus enabling computational error correction at a fraction of an overhead compared to conventional approaches. We use the RRNS scheme to design a Computationally-Redundant, Energy-Efficient core, including the microarchitecture, Instruction Set Architecture (ISA) and RRNS centered algorithms. Finally, from the simulation results, this RRNS system can reduce the energy-delay-product by about 3× for multiplication intensive workloads and by about 2× in general, when compared to a non-error-correcting binary core.« less

A joint signal processing and cryptographic approach to multimedia encryption.

PubMed

Mao, Yinian; Wu, Min

2006-07-01

In recent years, there has been an increasing trend for multimedia applications to use delegate service providers for content distribution, archiving, search, and retrieval. These delegate services have brought new challenges to the protection of multimedia content confidentiality. This paper discusses the importance and feasibility of applying a joint signal processing and cryptographic approach to multimedia encryption, in order to address the access control issues unique to multimedia applications. We propose two atomic encryption operations that can preserve standard compliance and are friendly to delegate processing. Quantitative analysis for these operations is presented to demonstrate that a good tradeoff can be made between security and bitrate overhead. In assisting the design and evaluation of media security systems, we also propose a set of multimedia-oriented security scores to quantify the security against approximation attacks and to complement the existing notion of generic data security. Using video as an example, we present a systematic study on how to strategically integrate different atomic operations to build a video encryption system. The resulting system can provide superior performance over both generic encryption and its simple adaptation to video in terms of a joint consideration of security, bitrate overhead, and friendliness to delegate processing.

2. TYPICAL OVERHEAD WIRE CONSTRUCTION CURVE GUY WIRE ARRANGEMENT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. TYPICAL OVERHEAD WIRE CONSTRUCTION - CURVE GUY WIRE ARRANGEMENT (ABANDONED WEST LEG OF WYE AT SIXTH AVENUE AND PINE STREET) - Yakima Valley Transportation Company Interurban Railroad, Trackage, Yakima, Yakima County, WA

Evaluation of overhead support inspection program.

DOT National Transportation Integrated Search

2015-01-01

This study evaluated the adequacy and frequency of the current structural support inspection program for overhead : sign supports (including bridge mounted), mast arm signal supports and high mast light supports. While ODOT provides : statewide guida...

Detail, east side, north end, showing door and overhead rail ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail, east side, north end, showing door and overhead rail for refrigeration room. - Fitzsimons General Hospital, Ice Plant, Southwest Corner of East I Avenue & North Thirteenth Street, Aurora, Adams County, CO

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR OF BUILDING 1. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Overhead Door Company of Charleston Information Sheet

EPA Pesticide Factsheets

Overhead Door Company of Charleston (the Company) is located in North Charleston, South Carolina. The settlement involves renovation activities conducted at a property constructed prior to 1978, located in Isle of Palms, South Carolina.

Enabling Diverse Software Stacks on Supercomputers using High Performance Virtual Clusters.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Younge, Andrew J.; Pedretti, Kevin; Grant, Ryan

While large-scale simulations have been the hallmark of the High Performance Computing (HPC) community for decades, Large Scale Data Analytics (LSDA) workloads are gaining attention within the scientific community not only as a processing component to large HPC simulations, but also as standalone scientific tools for knowledge discovery. With the path towards Exascale, new HPC runtime systems are also emerging in a way that differs from classical distributed com- puting models. However, system software for such capabilities on the latest extreme-scale DOE supercomputing needs to be enhanced to more appropriately support these types of emerging soft- ware ecosystems. In thismore » paper, we propose the use of Virtual Clusters on advanced supercomputing resources to enable systems to support not only HPC workloads, but also emerging big data stacks. Specifi- cally, we have deployed the KVM hypervisor within Cray's Compute Node Linux on a XC-series supercomputer testbed. We also use libvirt and QEMU to manage and provision VMs directly on compute nodes, leveraging Ethernet-over-Aries network emulation. To our knowledge, this is the first known use of KVM on a true MPP supercomputer. We investigate the overhead our solution using HPC benchmarks, both evaluating single-node performance as well as weak scaling of a 32-node virtual cluster. Overall, we find single node performance of our solution using KVM on a Cray is very efficient with near-native performance. However overhead increases by up to 20% as virtual cluster size increases, due to limitations of the Ethernet-over-Aries bridged network. Furthermore, we deploy Apache Spark with large data analysis workloads in a Virtual Cluster, ef- fectively demonstrating how diverse software ecosystems can be supported by High Performance Virtual Clusters.« less

Block-Level Added Redundancy Explicit Authentication for Parallelized Encryption and Integrity Checking of Processor-Memory Transactions

NASA Astrophysics Data System (ADS)

Elbaz, Reouven; Torres, Lionel; Sassatelli, Gilles; Guillemin, Pierre; Bardouillet, Michel; Martinez, Albert

The bus between the System on Chip (SoC) and the external memory is one of the weakest points of computer systems: an adversary can easily probe this bus in order to read private data (data confidentiality concern) or to inject data (data integrity concern). The conventional way to protect data against such attacks and to ensure data confidentiality and integrity is to implement two dedicated engines: one performing data encryption and another data authentication. This approach, while secure, prevents parallelizability of the underlying computations. In this paper, we introduce the concept of Block-Level Added Redundancy Explicit Authentication (BL-AREA) and we describe a Parallelized Encryption and Integrity Checking Engine (PE-ICE) based on this concept. BL-AREA and PE-ICE have been designed to provide an effective solution to ensure both security services while allowing for full parallelization on processor read and write operations and optimizing the hardware resources. Compared to standard encryption which ensures only confidentiality, we show that PE-ICE additionally guarantees code and data integrity for less than 4% of run-time performance overhead.

FNCS: A Framework for Power System and Communication Networks Co-Simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ciraci, Selim; Daily, Jeffrey A.; Fuller, Jason C.

2014-04-13

This paper describes the Fenix framework that uses a federated approach for integrating power grid and communication network simulators. Compared existing approaches, Fenix al- lows co-simulation of both transmission and distribution level power grid simulators with the communication network sim- ulator. To reduce the performance overhead of time synchro- nization, Fenix utilizes optimistic synchronization strategies that make speculative decisions about when the simulators are going to exchange messages. GridLAB-D (a distribution simulator), PowerFlow (a transmission simulator), and ns-3 (a telecommunication simulator) are integrated with the frame- work and are used to illustrate the enhanced performance pro- vided by speculative multi-threadingmore » on a smart grid applica- tion. Our speculative multi-threading approach achieved on average 20% improvement over the existing synchronization methods« less

BIOSPIDA: A Relational Database Translator for NCBI.

PubMed

Hagen, Matthew S; Lee, Eva K

2010-11-13

As the volume and availability of biological databases continue widespread growth, it has become increasingly difficult for research scientists to identify all relevant information for biological entities of interest. Details of nucleotide sequences, gene expression, molecular interactions, and three-dimensional structures are maintained across many different databases. To retrieve all necessary information requires an integrated system that can query multiple databases with minimized overhead. This paper introduces a universal parser and relational schema translator that can be utilized for all NCBI databases in Abstract Syntax Notation (ASN.1). The data models for OMIM, Entrez-Gene, Pubmed, MMDB and GenBank have been successfully converted into relational databases and all are easily linkable helping to answer complex biological questions. These tools facilitate research scientists to locally integrate databases from NCBI without significant workload or development time.

Efficient receiver tuning using differential evolution strategies

NASA Astrophysics Data System (ADS)

Wheeler, Caleb H.; Toland, Trevor G.

2016-08-01

Differential evolution (DE) is a powerful and computationally inexpensive optimization strategy that can be used to search an entire parameter space or to converge quickly on a solution. The Kilopixel Array Pathfinder Project (KAPPa) is a heterodyne receiver system delivering 5 GHz of instantaneous bandwidth in the tuning range of 645-695 GHz. The fully automated KAPPa receiver test system finds optimal receiver tuning using performance feedback and DE. We present an adaptation of DE for use in rapid receiver characterization. The KAPPa DE algorithm is written in Python 2.7 and is fully integrated with the KAPPa instrument control, data processing, and visualization code. KAPPa develops the technologies needed to realize heterodyne focal plane arrays containing 1000 pixels. Finding optimal receiver tuning by investigating large parameter spaces is one of many challenges facing the characterization phase of KAPPa. This is a difficult task via by-hand techniques. Characterizing or tuning in an automated fashion without need for human intervention is desirable for future large scale arrays. While many optimization strategies exist, DE is ideal for time and performance constraints because it can be set to converge to a solution rapidly with minimal computational overhead. We discuss how DE is utilized in the KAPPa system and discuss its performance and look toward the future of 1000 pixel array receivers and consider how the KAPPa DE system might be applied.

Development and modification of a single overhead camshaft 4-valve 4-stroke 135 cc formula varsity race car engine

NASA Astrophysics Data System (ADS)

Abdullah, M. A.; Tamaldin, N.; Rusnandi, H.; Manoharan, T.; Samsir, M. A.

2013-12-01

The engine that was chosen to be developed and modified is Yamaha LC 135 Single Overhead Camshaft (SOHC) 4-valve 4-stroke 135cc liquid-cooled engine. The engine selection is based on the specification, rule and regulation in UTeM Formula Varsity 2012 (FV 2012). The engine performance is determined by engine operating characteristics. The engine air flow affects the filtration, intake and exhaust systems. The heat from the engine rejected to the surrounding through the active cooling system which has radiator and fan. The selection of the engine is based on weighted decision matrix which consists of reliability, operating and maintenance cost, fuel consumption and weight. The score of the matrix is formulated based on relative weighted factor among the selections. It been compared between Yamaha LC 135 Single Overhead Camshaft (SOHC) 4-valve 4-stroke 135cc liquid-cooled engine, Honda Wave 125 X Air Cooled, 4 Cycle Engine Overhead Camshaft (OHC) and Suzuki Shogun RR 4 stroke air cooled Single Overhead Camshaft (SOHC). The modification is applied to the engine through the simulation and tuning of Capacitor Discharge Ignition (CDI).

23 CFR 140.907 - Overhead and indirect construction costs.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Overhead and indirect construction costs. 140.907 Section 140.907 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES... 18276, May 23, 1988] ...

23 CFR 140.907 - Overhead and indirect construction costs.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Overhead and indirect construction costs. 140.907 Section 140.907 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES... 18276, May 23, 1988] ...

23 CFR 140.907 - Overhead and indirect construction costs.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Overhead and indirect construction costs. 140.907 Section 140.907 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PAYMENT PROCEDURES... 18276, May 23, 1988] ...

Steel tanks T5 and T4 with overhead pipeline between. Redwood ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Steel tanks T5 and T4 with overhead pipeline between. Redwood tanks seen in background - Hawaii Volcanoes National Park Water Collection System, Hawaii Volcanoes National Park, Volcano, Hawaii County, HI

Overhead Projector Demonstrations: Tilted TOPS: Inclined Plane Projection.

ERIC Educational Resources Information Center

Alyea, Hubert N.

1989-01-01

The construction and uses of a device to facilitate the use of an overhead projector to show chemical reactions is presented. Materials and instructions for construction as well as reactor vessels are discussed. (CW)

Overhead guide sign retroreflectivity and illumination : [technical summary].

DOT National Transportation Integrated Search

2015-01-01

Compared to daylight driving, nighttime driving is more demanding because of visibility : issues, such as a drivers visual acuity, contrast sensitivity, distance judgment, and : color discrimination. Overhead highway signs are very important for e...

Systems and methods for reactive distillation with recirculation of light components

DOEpatents

Stickney, Michael J [Nassau Bay, TX; Jones, Jr., Edward M.

2011-07-26

Systems and methods for producing gas-to-liquids products using reactive distillation are provided. The method for producing gas-to-liquids products can include reacting a feedstock in a column having a distillation zone and a reaction zone to provide a bottoms stream and an overhead stream. A first portion of the overhead stream can be recycled to the column at the top of the reaction zone and second portion of the overhead stream can be recycled to the column at the bottom of the reaction zone.

Toward an optimal online checkpoint solution under a two-level HPC checkpoint model

DOE PAGES

Di, Sheng; Robert, Yves; Vivien, Frederic; ...

2016-03-29

The traditional single-level checkpointing method suffers from significant overhead on large-scale platforms. Hence, multilevel checkpointing protocols have been studied extensively in recent years. The multilevel checkpoint approach allows different levels of checkpoints to be set (each with different checkpoint overheads and recovery abilities), in order to further improve the fault tolerance performance of extreme-scale HPC applications. How to optimize the checkpoint intervals for each level, however, is an extremely difficult problem. In this paper, we construct an easy-to-use two-level checkpoint model. Checkpoint level 1 deals with errors with low checkpoint/recovery overheads such as transient memory errors, while checkpoint level 2more » deals with hardware crashes such as node failures. Compared with previous optimization work, our new optimal checkpoint solution offers two improvements: (1) it is an online solution without requiring knowledge of the job length in advance, and (2) it shows that periodic patterns are optimal and determines the best pattern. We evaluate the proposed solution and compare it with the most up-to-date related approaches on an extreme-scale simulation testbed constructed based on a real HPC application execution. Simulation results show that our proposed solution outperforms other optimized solutions and can improve the performance significantly in some cases. Specifically, with the new solution the wall-clock time can be reduced by up to 25.3% over that of other state-of-the-art approaches. Lastly, a brute-force comparison with all possible patterns shows that our solution is always within 1% of the best pattern in the experiments.« less

Overhead traffic detector mounting system (Phase 2).

DOT National Transportation Integrated Search

2007-04-01

Caltrans has funded the development of a new family of out-of-pavement electronic sensing devices for the purpose of monitoring certain characteristics of highway traffic. One promising example is a laser based overhead detector recently developed at...

32. VIEW FROM CATWALK SHOWING ROOF TRUSSES, OVERHEAD CRANE, AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

32. VIEW FROM CATWALK SHOWING ROOF TRUSSES, OVERHEAD CRANE, AND MISCELLANEOUS STOCK AND PATTERNS-LOOKING SOUTHWEST. - W. A. Young & Sons Foundry & Machine Shop, On Water Street along Monongahela River, Rices Landing, Greene County, PA

Overhead tray for cable test system

NASA Technical Reports Server (NTRS)

Saltz, K. T.

1976-01-01

System consists of overhead slotted tray, series of compatible adapter cables, and automatic test set which consists of control console and cable-switching console. System reduces hookup time and also reduces cost of fabricating and storing test cables.

Minimum retroreflectivity levels for overhead guide signs and street-name signs

DOT National Transportation Integrated Search

2003-12-01

In 1993, the Federal Highway Administration (FHWA) published research recommendations for minimum retroreflectivity (MR) levels for traffic signs. The recommendations included overhead signs, but not street-name signs. In revisions to the recommended...

Interior view of main section of milk barn. Opening overhead ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view of main section of milk barn. Opening overhead leads to attic crawl space. Camera is pointed SW. - Kosai Farm, Milk Barn, B Street north of Northwest Twenty-ninth Street, Auburn, King County, WA

12. Interior view, grain tanks (bins). Profile view of overhead ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. Interior view, grain tanks (bins). Profile view of overhead (fill) conveyor gallery bridge extending through tops of tanks just below roofs. - Saint Anthony Elevator No. 3, 620 Malcom Avenue, Southeast, Minneapolis, Hennepin County, MN

Overhead Projector Demonstrations: A Classroom Demonstration of Aliphatic Substitution.

ERIC Educational Resources Information Center

Perina, Ivo; Mihanovic, Branka

1989-01-01

Presents a halogen substitution of an alkane using a compartmentalized Petri dish or Conway dish on an overhead projector. Provides methodology and several modifications for different reactions. Uses hexane, methyl orange, bromine, and silver nitrate. (MVL)

Communication overhead on the Intel Paragon, IBM SP2 and Meiko CS-2

NASA Technical Reports Server (NTRS)

Bokhari, Shahid H.

1995-01-01

Interprocessor communication overhead is a crucial measure of the power of parallel computing systems-its impact can severely limit the performance of parallel programs. This report presents measurements of communication overhead on three contemporary commercial multicomputer systems: the Intel Paragon, the IBM SP2 and the Meiko CS-2. In each case the time to communicate between processors is presented as a function of message length. The time for global synchronization and memory access is discussed. The performance of these machines in emulating hypercubes and executing random pairwise exchanges is also investigated. It is shown that the interprocessor communication time depends heavily on the specific communication pattern required. These observations contradict the commonly held belief that communication overhead on contemporary machines is independent of the placement of tasks on processors. The information presented in this report permits the evaluation of the efficiency of parallel algorithm implementations against standard baselines.

Confidential and Authenticated Communications in a Large Fixed-Wing UAV Swarm

DTIC Science & Technology

2016-12-01

either a UAV or a ground station. Asymmetric cryptography is not an option for swarm communications. It is a potential option for initially keying or...each UAV grows ten bytes for each UAV in the swarm, and a 30% overhead is added on for worst case cryptography . The resulting throughput is...analysis in Section IV, we can predict the burden that cryptography places on the ODroid computer. Given that the average unencrypted message size was

Crossing Phenomena in Overhead Line Equipment (OHLE) Structure in 3D Space Considering Soil-Structure Interaction

NASA Astrophysics Data System (ADS)

Ngamkhanong, Chayut; Kaewunruen, Sakdirat; Baniotopoulos, Charalampos; Papaelias, Mayorkinos

2017-10-01

Nowadays, the electric train becomes one of the efficient railway systems that are lighter, cleaner, quieter, cheaper and faster than a conventional train. Overhead line equipment (OHLE), which supplies electric power to the trains, is designed on the principle of overhead wires placed over the railway track. The OHLE is supported by mast structure which located at the lineside along the track. Normally, mast structure is a steel column or truss structure which supports the overhead wire carrying the power. Due to the running train and severe periodic force, such as an earthquake, in surrounding area may cause damage to the OHLE structure especially mast structure which leads to the failure of the electrical system. The mast structure needs to be discussed in order to resist the random forces. Due to the vibration effect, the natural frequencies of the structure are necessary. This is because when the external applied force occurs within a range of frequency of the structure, resonance effect can be expected which lead to the large oscillations and deflections. The natural frequency of a system is dependent only on the stiffness of the structure and the mass which participates with the structure, including self-weight. The modal analysis is used in order to calculate the mode shapes and natural frequencies of the mast structure during free vibration. A mast structure with varying rotational soil stiffness is used to observe the influence of soil-structure action. It is common to use finite element analysis to perform a modal analysis. This paper presents the fundamental mode shapes, natural frequencies and crossing phenomena of three-dimensional mast structure considering soil-structure interaction. The sensitivity of mode shapes to the variation of soil-structure interaction is discussed. The outcome of this study will improve the understanding of the fundamental dynamic behaviour of the mast structure which supports the OHLE. Moreover, this study will be a recommendation for the structural engineer to associate with the behaviour of mast structure during vibration.

Influence of Body Position on Shoulder and Trunk Muscle Activation During Resisted Isometric Shoulder External Rotation.

PubMed

Krause, David A; Dueffert, Lucas G; Postma, Jaclyn L; Vogler, Eric T; Walsh, Amy J; Hollman, John H

External rotation (ER) strengthening of the shoulder is an integral component of rehabilitative and preventative programs for overhead athletes. A variety of shoulder ER strengthening exercises are reported, including those intended to integrate the core musculature. The purpose of this study was to examine ER torque and electromyographic (EMG) activation of shoulder and trunk muscles while performing resisted isometric shoulder ER in 3 positions (standing, side lying, and side plank). Significantly greater force and shoulder muscle activation would be generated while side lying given the inherent stability of the position, and greater trunk muscle activation would be generated in the less stable plank position. Quasi-experimental repeated-measures study. Level 5. A convenience sample of 25 healthy overhead recreational athletes (9 men, 16 women) participated in this study. EMG electrodes were placed on the infraspinatus, posterior deltoid, middle trapezius, multifidi, internal obliques, and external obliques. EMG signals were normalized to a maximal isometric contraction. Participants performed resisted isometric ER in standing, side-lying, and side plank positions. Results were analyzed using a repeated-measures analysis of variance with post hoc Bonferroni corrections (α = 0.05). There was no significant difference in ER torque between positions (α = 0.05). A significant difference in EMG activity of shoulder and trunk musculature between positions was found in 7 of the 8 muscles monitored. Significantly greater EMG activity in the infraspinatus, middle trapezius, and the nondominant external and internal obliques was found in the side plank position as compared with standing and side lying. While there was no difference in ER torque between the 3 exercise positions, EMG activity of the shoulder and trunk muscles was dependent on body position. If a clinician is seeking to integrate trunk muscle activation while performing shoulder ER strengthening, the side plank position is preferred as compared with standing or side lying.

The role of handouts, note-taking and overhead transparencies in veterinary science lectures.

PubMed

McLennan, M W; Isaacs, G

2002-10-01

To study student and staff views of the role and use of handouts, note-taking and overhead transparencies in veterinary science lectures at the University of Queensland The Nominal Group Technique was used to help develop a questionnaire, which was completed by 351 students (a response rate of 84%) and 35 staff (76%) from the 5 years of the veterinary course. The data were analysed using the SAS statistical computer package. Staff and students held different views as to the frequency with which handouts should be used, their educational value, and whether they should be complete or partial. Fewer students than staff agreed that handouts discourage further reading in a subject. Almost all staff and students saw the central functions of note-taking to be provision of notes for subsequent revision and encoding information given by the lecturer. More students than staff however, considered that note-taking in lectures interferes with understanding. Staff and students held similar views as to the uses of overheads in lectures. Interestingly however, more staff than students agreed that overheads often contain too much information. Both students and staff saw the central role of note-taking as providing a set of good notes for revision. Generally students preferred that this information be provided in the form of partial or complete handouts, while staff preferred students to take notes and to read outside lectures. Surprisingly, more staff than students felt that overhead transparencies often contained too much information. Note-taking, handouts and overhead transparencies need to be linked in a coherent educational strategy to promote effective learning.

Eccentric and isometric shoulder rotator cuff strength testing using a hand-held dynamometer: reference values for overhead athletes.

PubMed

Cools, Ann M J; Vanderstukken, Fran; Vereecken, Frédéric; Duprez, Mattias; Heyman, Karel; Goethals, Nick; Johansson, Fredrik

2016-12-01

In order to provide science-based guidelines for injury prevention or return to play, regular measurement of isometric and eccentric internal (IR) and external (ER) rotator strength is warranted in overhead athletes. However, up to date, no normative database exists regarding these values, when measured with a hand-held dynamometer. Therefore, the purpose of the study was to provide a normative database on isometric and eccentric rotator cuff (RC) strength values in a sample of overhead athletes, and to discuss gender, age and sports differences. A HHD was used to measure RC strength in 201 overhead athletes between 18 and 50 years old from three different sports disciplines: tennis, volleyball and handball. Isometric as well as eccentric strength was measured in different shoulder positions. Outcome variables of interest were isometric ER and IR strength, eccentric ER strength, and intermuscular strength ratios ER/IR. Our results show significant side, gender and sports discipline differences in the isometric and eccentric RC strength. However, when normalized to body weight, gender differences often are absent. In general, strength differences are in favour of the dominant side, the male athletes and handball. Intermuscular ER/IR ratios showed gender, sports, and side differences. This normative database is necessary to help the clinician in the evaluation of RC strength in healthy and injured overhead athletes. In view of the preventive screening and return-to-play decisions in overhead athletes, normalization to body weight and calculating intermuscular ratios are key points in this evaluation. Diagnostic study, Level III.

15. VIEW OF THE ORIGINAL 10TON OVERHEAD NILES TRAVELING CRANE. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

15. VIEW OF THE ORIGINAL 10-TON OVERHEAD NILES TRAVELING CRANE. - Washington Water Power Company Post Falls Power Plant, Middle Channel Powerhouse & Dam, West of intersection of Spokane & Fourth Streets, Post Falls, Kootenai County, ID

The applicability of high intensity sheeting on overhead highway signs.

DOT National Transportation Integrated Search

1975-01-01

This report summarizes (1) the findings of a research study on the applicability of using high intensity reflective sheeting on overhead signs, and (2) the implementation of recommendations evolving from these findings through elimination of the illu...

33 CFR 80.707 - Cape Romain, SC to Sullivans Island, SC.

Code of Federal Regulations, 2013 CFR

2013-07-01

... the easternmost extremity of Capers Island. (d) A line formed by the overhead power cable from Capers Island to Dewees Island. (e) A line formed by the overhead power cable from Dewees Island to Isle of...

33 CFR 80.707 - Cape Romain, SC to Sullivans Island, SC.

Code of Federal Regulations, 2014 CFR

2014-07-01

... the easternmost extremity of Capers Island. (d) A line formed by the overhead power cable from Capers Island to Dewees Island. (e) A line formed by the overhead power cable from Dewees Island to Isle of...

Fatigue Analysis of Overhead Sign and Signal Structures

DOT National Transportation Integrated Search

1994-05-01

This report documents methods of fatigue analysis for overhead sign and signal structures. The main purpose of this report is to combine pertinent wind loading and vibration theory, fatigue damage theory, and experimental data into a useable fatigue ...

Centripetal Force on an Overhead Projector.

ERIC Educational Resources Information Center

Rheam, Harry

1995-01-01

Describes two simple demonstrations of an object moving in a straight line tangent to the circle if centripetal force is removed. Demonstrations use a pie plate and petri dish with ball bearings to illustrate the phenomena on an overhead projector. (LZ)

Evaluation of high intensity sheeting for overhead highway signs.

DOT National Transportation Integrated Search

1974-01-01

The current practice in Virginia is to reflectorize and illuminate all overhead highway signs because of their important role in the safe and orderly flow of traffic. Reflectorization is obtained by using reflective sheeting as background and legend ...

Evaluation of Guide Sign Fonts

DOT National Transportation Integrated Search

2014-04-01

Researchers at Texas A&M Transportation Institute completed a study of E-modified, Enhanced E-Modified, and Clearview 5W for overhead and shoulder-mounted guide signs. The overhead guide signed consisted of three six-letter words stacked over each ot...

STS-98 U.S. Lab payload is moved to stand for weight determination

NASA Technical Reports Server (NTRS)

2000-01-01

KENNEDY SPACE CENTER, Fla. -- In the Space Station Processing Facility, the 'key' to the U.S. Laboratory Destiny is officially handed over to NASA during a brief ceremony while workers look on. Suspended overhead is the laboratory, being moved to the Launch Package Integration Stand (LPIS) for a weight and center of gravity determination. Destiny is the payload aboard Space Shuttle Atlantis on mission STS-98 to the International Space Station. The lab is fitted with five system racks and will already have experiments installed inside for the flight. The launch is scheduled for January 2001.

Moving THEMIS to a spin table for testing at Astrotech

NASA Image and Video Library

2007-01-12

In the Hazardous Processing Facility at Astrotech Space Operations, workers attach an overhead crane to the integrated THEMIS spacecraft. The carrier is being moved to a spin table for spin-balance testing. THEMIS consists of five identical probes, the largest number of scientific satellites ever launched into orbit aboard a single rocket. This unique constellation of satellites will resolve the tantalizing mystery of what causes the spectacular sudden brightening of the aurora borealis and aurora australis - the fiery skies over the Earth's northern and southern polar regions. THEMIS is scheduled to launch Feb. 15 from Cape Canaveral Air Force Station.

KSC-08pd2356

NASA Image and Video Library

2008-08-08

CAPE CANAVERAL, Fla. – In the Payload Hazardous Servicing Facility at NASA's Kennedy Space Center, an overhead crane moves the Fine Guidance Sensor Scientific Instrument Protective Enclosure, or FSIPE, cover to be installed on the Orbital Replacement Unit Carrier, or ORUC, below. The ORUC is one of three carriers that are being prepared for the integration of telescope science instruments, both internal and external replacement components, as well as the flight support equipment to be used by the astronauts during the fifth and final Hubble servicing mission, STS-125. Launch is targeted for Oct. 8. PHoto credit: NASA/Jack Pfaller

KSC-2011-3887

NASA Image and Video Library

2011-03-21

VANDENBERG AIR FORCE BASE, Calif. -- Workers attach cables from an overhead crane to the United Launch Alliance Delta II second stage motor for mating to the first stage at NASA's Space Launch Complex-2 (SLC-2) at Vandenberg Air Force Base in California. Following final tests, the Aquarius/SAC-D spacecraft will be integrated to the Delta II launch vehicle in preparation for the targeted June liftoff. Aquarius, the NASA-built instrument on the SAC-D spacecraft will provide new insights into how variations in ocean surface salinity relate to fundamental climate processes on its three-year mission. Photo credit: NASA/VAFB

A Secure Communication Suite for Underwater Acoustic Sensor Networks

PubMed Central

Dini, Gianluca; Duca, Angelica Lo

2012-01-01

In this paper we describe a security suite for Underwater Acoustic Sensor Networks comprising both fixed and mobile nodes. The security suite is composed of a secure routing protocol and a set of cryptographic primitives aimed at protecting the confidentiality and the integrity of underwater communication while taking into account the unique characteristics and constraints of the acoustic channel. By means of experiments and simulations based on real data, we show that the suite is suitable for an underwater networking environment as it introduces limited, and sometimes negligible, communication and power consumption overhead. PMID:23202204

STS-105 ICC is moved to the payload canister for transport to pad 39A

NASA Technical Reports Server (NTRS)

2001-01-01

KENNEDY SPACE CENTER, Fla. -- An overhead crane in the Space Station Processing Facility lifts the Integrated Cargo Carrier from its workstand to move it to the payload canister. The ICC holds several payloads for mission STS-105, the Early Ammonia Servicer and two experiment containers. The ICC will join the Multi-Purpose Logistics Module Leonardo in the payload canister for transport to Launch Pad 39A where they will be placed in the payload bay of Space Shuttle Discovery. Launch of STS-105 is scheduled for 5:38 p.m. EDT Aug. 9

STS-105 ICC is moved to the payload canister for transport to pad 39A

NASA Technical Reports Server (NTRS)

2001-01-01

KENNEDY SPACE CENTER, Fla. -- An overhead crane in the Space Station Processing Facility moves the Integrated Cargo Carrier toward the payload canister (right). The ICC holds several payloads for mission STS-105, the Early Ammonia Servicer and two experiment containers. The ICC will join the Multi-Purpose Logistics Module Leonardo already in the payload canister for transport to Launch Pad 39A where they will be placed in the payload bay of Space Shuttle Discovery. Launch of STS-105 is scheduled for 5:38 p.m. EDT Aug. 9

The Z1 truss is lowered to stand to check weight and balance

NASA Technical Reports Server (NTRS)

2000-01-01

In the Space Station Processing Facility, an overhead crane lowers the Integrated Truss Structure Z1 onto a workstand to check its weight and balance. The Z1 truss is the first of 10 trusses that will become the backbone of the International Space Station, eventually stretching the length of a football field. Along with its companion payload, the third Pressurized Mating Adapter, the Z1 is scheduled to be launched aboard Space Shuttle Discovery Oct. 5 at 9:38 p.m. EDT. The launch will be the 100th in the Shuttle program.

Overhead spine arch analysis of dairy cows from three-dimensional video

NASA Astrophysics Data System (ADS)

Abdul Jabbar, K.; Hansen, M. F.; Smith, M. L.; Smith, L. N.

2017-02-01

We present a spine arch analysis method in dairy cows using overhead 3D video data. This method is aimed for early stage lameness detection. That is important in order to allow early treatment; and thus, reduce the animal suffering and minimize the high forecasted financial losses, caused by lameness. Our physical data collection setup is non-intrusive, covert and designed to allow full automation; therefore, it could be implemented on a large scale or daily basis with high accuracy. We track the animal's spine using shape index and curvedness measure from the 3D surface as she walks freely under the 3D camera. Our spinal analysis focuses on the thoracic vertebrae region, where we found most of the arching caused by lameness. A cubic polynomial is fitted to analyze the arch and estimate the locomotion soundness. We have found more accurate results by eliminating the regular neck/head movements' effect from the arch. Using 22-cow data set, we are able to achieve an early stage lameness detection accuracy of 95.4%.

PRESAGE: Protecting Structured Address Generation against Soft Errors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Vishal C.; Gopalakrishnan, Ganesh; Krishnamoorthy, Sriram

Modern computer scaling trends in pursuit of larger component counts and power efficiency have, unfortunately, lead to less reliable hardware and consequently soft errors escaping into application data ("silent data corruptions"). Techniques to enhance system resilience hinge on the availability of efficient error detectors that have high detection rates, low false positive rates, and lower computational overhead. Unfortunately, efficient detectors to detect faults during address generation (to index large arrays) have not been widely researched. We present a novel lightweight compiler-driven technique called PRESAGE for detecting bit-flips affecting structured address computations. A key insight underlying PRESAGE is that any addressmore » computation scheme that flows an already incurred error is better than a scheme that corrupts one particular array access but otherwise (falsely) appears to compute perfectly. Enabling the flow of errors allows one to situate detectors at loop exit points, and helps turn silent corruptions into easily detectable error situations. Our experiments using PolyBench benchmark suite indicate that PRESAGE-based error detectors have a high error-detection rate while incurring low overheads.« less

PRESAGE: Protecting Structured Address Generation against Soft Errors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Vishal C.; Gopalakrishnan, Ganesh; Krishnamoorthy, Sriram

Modern computer scaling trends in pursuit of larger component counts and power efficiency have, unfortunately, lead to less reliable hardware and consequently soft errors escaping into application data ("silent data corruptions"). Techniques to enhance system resilience hinge on the availability of efficient error detectors that have high detection rates, low false positive rates, and lower computational overhead. Unfortunately, efficient detectors to detect faults during address generation have not been widely researched (especially in the context of indexing large arrays). We present a novel lightweight compiler-driven technique called PRESAGE for detecting bit-flips affecting structured address computations. A key insight underlying PRESAGEmore » is that any address computation scheme that propagates an already incurred error is better than a scheme that corrupts one particular array access but otherwise (falsely) appears to compute perfectly. Ensuring the propagation of errors allows one to place detectors at loop exit points and helps turn silent corruptions into easily detectable error situations. Our experiments using the PolyBench benchmark suite indicate that PRESAGE-based error detectors have a high error-detection rate while incurring low overheads.« less

Mobility based key management technique for multicast security in mobile ad hoc networks.

PubMed

Madhusudhanan, B; Chitra, S; Rajan, C

2015-01-01

In MANET multicasting, forward and backward secrecy result in increased packet drop rate owing to mobility. Frequent rekeying causes large message overhead which increases energy consumption and end-to-end delay. Particularly, the prevailing group key management techniques cause frequent mobility and disconnections. So there is a need to design a multicast key management technique to overcome these problems. In this paper, we propose the mobility based key management technique for multicast security in MANET. Initially, the nodes are categorized according to their stability index which is estimated based on the link availability and mobility. A multicast tree is constructed such that for every weak node, there is a strong parent node. A session key-based encryption technique is utilized to transmit a multicast data. The rekeying process is performed periodically by the initiator node. The rekeying interval is fixed depending on the node category so that this technique greatly minimizes the rekeying overhead. By simulation results, we show that our proposed approach reduces the packet drop rate and improves the data confidentiality.

Testing of the 3M Company Composite Conductor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stovall, John P; Rizy, D Tom; Kisner, Roger A

2010-10-01

The 3M Company has developed a high-temperature low-sag conductor referred to as Aluminum-Conductor Composite-Reinforced or ACCR. The conductor uses an aluminum metal matrix material to replace the steel in conventional conductors. The objective of this work is to accelerate the commercial acceptance by electric utilities of this new conductor design by testing four representative conductor classes in controlled conditions. A unique facility called the Powerline Conductor Accelerated Testing (PCAT) Facility was built at ORNL for testing overhead conductors. The PCAT has been uniquely designed for testing overhead bare transmission line conductors at high currents and temperatures after they have beenmore » installed and tensioned to the manufacturer's specifications. The ability to operate a transmission line conductor in this manner does not exist elsewhere in the United States. Four classes of ACCR cable designed by the 3M Company have been successfully test at ORNL small, medium, large and small/compact. Based on these and other manufacturer tests, the 3M Company has successfully introduced the ACCR into the commercial market and has completed over twenty installations for utility companies.« less

Re-Organizing Earth Observation Data Storage to Support Temporal Analysis of Big Data

NASA Technical Reports Server (NTRS)

Lynnes, Christopher

2017-01-01

The Earth Observing System Data and Information System archives many datasets that are critical to understanding long-term variations in Earth science properties. Thus, some of these are large, multi-decadal datasets. Yet the challenge in long time series analysis comes less from the sheer volume than the data organization, which is typically one (or a small number of) time steps per file. The overhead of opening and inventorying complex, API-driven data formats such as Hierarchical Data Format introduces a small latency at each time step, which nonetheless adds up for datasets with O(10^6) single-timestep files. Several approaches to reorganizing the data can mitigate this overhead by an order of magnitude: pre-aggregating data along the time axis (time-chunking); storing the data in a highly distributed file system; or storing data in distributed columnar databases. Storing a second copy of the data incurs extra costs, so some selection criteria must be employed, which would be driven by expected or actual usage by the end user community, balanced against the extra cost.

Re-organizing Earth Observation Data Storage to Support Temporal Analysis of Big Data

NASA Astrophysics Data System (ADS)

Lynnes, C.

2017-12-01

The Earth Observing System Data and Information System archives many datasets that are critical to understanding long-term variations in Earth science properties. Thus, some of these are large, multi-decadal datasets. Yet the challenge in long time series analysis comes less from the sheer volume than the data organization, which is typically one (or a small number of) time steps per file. The overhead of opening and inventorying complex, API-driven data formats such as Hierarchical Data Format introduces a small latency at each time step, which nonetheless adds up for datasets with O(10^6) single-timestep files. Several approaches to reorganizing the data can mitigate this overhead by an order of magnitude: pre-aggregating data along the time axis (time-chunking); storing the data in a highly distributed file system; or storing data in distributed columnar databases. Storing a second copy of the data incurs extra costs, so some selection criteria must be employed, which would be driven by expected or actual usage by the end user community, balanced against the extra cost.

Measuring zebrafish turning rate.

PubMed

Mwaffo, Violet; Butail, Sachit; di Bernardo, Mario; Porfiri, Maurizio

2015-06-01

Zebrafish is becoming a popular animal model in preclinical research, and zebrafish turning rate has been proposed for the analysis of activity in several domains. The turning rate is often estimated from the trajectory of the fish centroid that is output by commercial or custom-made target tracking software run on overhead videos of fish swimming. However, the accuracy of such indirect methods with respect to the turning rate associated with changes in heading during zebrafish locomotion is largely untested. Here, we compare two indirect methods for the turning rate estimation using the centroid velocity or position data, with full shape tracking for three different video sampling rates. We use tracking data from the overhead video recorded at 60, 30, and 15 frames per second of zebrafish swimming in a shallow water tank. Statistical comparisons of absolute turning rate across methods and sampling rates indicate that, while indirect methods are indistinguishable from full shape tracking, the video sampling rate significantly influences the turning rate measurement. The results of this study can aid in the selection of the video capture frame rate, an experimental design parameter in zebrafish behavioral experiments where activity is an important measure.

NOA: A Scalable Multi-Parent Clustering Hierarchy for WSNs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cree, Johnathan V.; Delgado-Frias, Jose; Hughes, Michael A.

2012-08-10

NOA is a multi-parent, N-tiered, hierarchical clustering algorithm that provides a scalable, robust and reliable solution to autonomous configuration of large-scale wireless sensor networks. The novel clustering hierarchy's inherent benefits can be utilized by in-network data processing techniques to provide equally robust, reliable and scalable in-network data processing solutions capable of reducing the amount of data sent to sinks. Utilizing a multi-parent framework, NOA reduces the cost of network setup when compared to hierarchical beaconing solutions by removing the expense of r-hop broadcasting (r is the radius of the cluster) needed to build the network and instead passes network topologymore » information among shared children. NOA2, a two-parent clustering hierarchy solution, and NOA3, the three-parent variant, saw up to an 83% and 72% reduction in overhead, respectively, when compared to performing one round of a one-parent hierarchical beaconing, as well as 92% and 88% less overhead when compared to one round of two- and three-parent hierarchical beaconing hierarchy.« less

A survey on routing protocols for large-scale wireless sensor networks.

PubMed

Li, Changle; Zhang, Hanxiao; Hao, Binbin; Li, Jiandong

2011-01-01

With the advances in micro-electronics, wireless sensor devices have been made much smaller and more integrated, and large-scale wireless sensor networks (WSNs) based the cooperation among the significant amount of nodes have become a hot topic. "Large-scale" means mainly large area or high density of a network. Accordingly the routing protocols must scale well to the network scope extension and node density increases. A sensor node is normally energy-limited and cannot be recharged, and thus its energy consumption has a quite significant effect on the scalability of the protocol. To the best of our knowledge, currently the mainstream methods to solve the energy problem in large-scale WSNs are the hierarchical routing protocols. In a hierarchical routing protocol, all the nodes are divided into several groups with different assignment levels. The nodes within the high level are responsible for data aggregation and management work, and the low level nodes for sensing their surroundings and collecting information. The hierarchical routing protocols are proved to be more energy-efficient than flat ones in which all the nodes play the same role, especially in terms of the data aggregation and the flooding of the control packets. With focus on the hierarchical structure, in this paper we provide an insight into routing protocols designed specifically for large-scale WSNs. According to the different objectives, the protocols are generally classified based on different criteria such as control overhead reduction, energy consumption mitigation and energy balance. In order to gain a comprehensive understanding of each protocol, we highlight their innovative ideas, describe the underlying principles in detail and analyze their advantages and disadvantages. Moreover a comparison of each routing protocol is conducted to demonstrate the differences between the protocols in terms of message complexity, memory requirements, localization, data aggregation, clustering manner and other metrics. Finally some open issues in routing protocol design in large-scale wireless sensor networks and conclusions are proposed.

A Survey on Routing Protocols for Large-Scale Wireless Sensor Networks

PubMed Central

Li, Changle; Zhang, Hanxiao; Hao, Binbin; Li, Jiandong

2011-01-01

With the advances in micro-electronics, wireless sensor devices have been made much smaller and more integrated, and large-scale wireless sensor networks (WSNs) based the cooperation among the significant amount of nodes have become a hot topic. “Large-scale” means mainly large area or high density of a network. Accordingly the routing protocols must scale well to the network scope extension and node density increases. A sensor node is normally energy-limited and cannot be recharged, and thus its energy consumption has a quite significant effect on the scalability of the protocol. To the best of our knowledge, currently the mainstream methods to solve the energy problem in large-scale WSNs are the hierarchical routing protocols. In a hierarchical routing protocol, all the nodes are divided into several groups with different assignment levels. The nodes within the high level are responsible for data aggregation and management work, and the low level nodes for sensing their surroundings and collecting information. The hierarchical routing protocols are proved to be more energy-efficient than flat ones in which all the nodes play the same role, especially in terms of the data aggregation and the flooding of the control packets. With focus on the hierarchical structure, in this paper we provide an insight into routing protocols designed specifically for large-scale WSNs. According to the different objectives, the protocols are generally classified based on different criteria such as control overhead reduction, energy consumption mitigation and energy balance. In order to gain a comprehensive understanding of each protocol, we highlight their innovative ideas, describe the underlying principles in detail and analyze their advantages and disadvantages. Moreover a comparison of each routing protocol is conducted to demonstrate the differences between the protocols in terms of message complexity, memory requirements, localization, data aggregation, clustering manner and other metrics. Finally some open issues in routing protocol design in large-scale wireless sensor networks and conclusions are proposed. PMID:22163808

Out-of-hours primary care. Implications of organisation on costs

PubMed Central

van Uden, Caro JT; Ament, Andre JHA; Voss, Gemma BWE; Wesseling, Geertjan; Winkens, Ron AG; van Schayck, Onno CP; Crebolder, Harry FJM

2006-01-01

Background To perform out-of-hours primary care, Dutch general practitioners (GPs) have organised themselves in large-scale GP cooperatives. Roughly, two models of out-of-hours care can be distinguished; GP cooperatives working separate from the hospital emergency department (ED) and GP cooperatives integrated with the hospital ED. Research has shown differences in care utilisation between these two models; a significant shift in the integrated model from utilisation of ED care to primary care. These differences may have implications on costs, however, until now this has not been investigated. This study was performed to provide insight in costs of these two different models of out-of-hours care. Methods Annual reports of two GP cooperatives (one separate from and one integrated with a hospital emergency department) in 2003 were analysed on costs and use of out-of-hours care. Costs were calculated per capita. Comparisons were made between the two cooperatives. In addition, a comparison was made between the costs of the hospital ED of the integrated model before and after the set up of the GP cooperative were analysed. Results Costs per capita of the GP cooperative in the integrated model were slightly higher than in the separate model (ε 11.47 and ε 10.54 respectively). Differences were mainly caused by personnel and other costs, including transportation, interest, cleaning, computers and overhead. Despite a significant reduction in patients utilising ED care as a result of the introduction of the GP cooperative integrated within the ED, the costs of the ED remained the same. Conclusion The study results show that the costs of primary care appear to be more dependent on the size of the population the cooperative covers than on the way the GP cooperative is organised, i.e. separated versus integrated. In addition, despite the substantial reduction of patients, locating the GP cooperative at the same site as the ED was found to have little effect on costs of the ED. Sharing more facilities and personnel between the ED and the GP cooperative may improve cost-efficiency. PMID:16674814

Out-of-hours primary care. Implications of organisation on costs.

PubMed

van Uden, Caro J T; Ament, Andre J H A; Voss, Gemma B W E; Wesseling, Geertjan; Winkens, Ron A G; van Schayck, Onno C P; Crebolder, Harry F J M

2006-05-04

To perform out-of-hours primary care, Dutch general practitioners (GPs) have organised themselves in large-scale GP cooperatives. Roughly, two models of out-of-hours care can be distinguished; GP cooperatives working separate from the hospital emergency department (ED) and GP cooperatives integrated with the hospital ED. Research has shown differences in care utilisation between these two models; a significant shift in the integrated model from utilisation of ED care to primary care. These differences may have implications on costs, however, until now this has not been investigated. This study was performed to provide insight in costs of these two different models of out-of-hours care. Annual reports of two GP cooperatives (one separate from and one integrated with a hospital emergency department) in 2003 were analysed on costs and use of out-of-hours care. Costs were calculated per capita. Comparisons were made between the two cooperatives. In addition, a comparison was made between the costs of the hospital ED of the integrated model before and after the set up of the GP cooperative were analysed. Costs per capita of the GP cooperative in the integrated model were slightly higher than in the separate model (epsilon 11.47 and epsilon 10.54 respectively). Differences were mainly caused by personnel and other costs, including transportation, interest, cleaning, computers and overhead. Despite a significant reduction in patients utilising ED care as a result of the introduction of the GP cooperative integrated within the ED, the costs of the ED remained the same. The study results show that the costs of primary care appear to be more dependent on the size of the population the cooperative covers than on the way the GP cooperative is organised, i.e. separated versus integrated. In addition, despite the substantial reduction of patients, locating the GP cooperative at the same site as the ED was found to have little effect on costs of the ED. Sharing more facilities and personnel between the ED and the GP cooperative may improve cost-efficiency.

29 CFR 1926.554 - Overhead hoists.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 8 2011-07-01 2011-07-01 false Overhead hoists. 1926.554 Section 1926.554 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors...

29 CFR 1926.554 - Overhead hoists.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Overhead hoists. 1926.554 Section 1926.554 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors...

29 CFR 1926.554 - Overhead hoists.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 8 2013-07-01 2013-07-01 false Overhead hoists. 1926.554 Section 1926.554 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors...

29 CFR 1926.554 - Overhead hoists.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Overhead hoists. 1926.554 Section 1926.554 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Helicopters, Hoists, Elevators, and Conveyors...

A new deadlock resolution protocol and message matching algorithm for the extreme-scale simulator

DOE PAGES

Engelmann, Christian; Naughton, III, Thomas J.

2016-03-22

Investigating the performance of parallel applications at scale on future high-performance computing (HPC) architectures and the performance impact of different HPC architecture choices is an important component of HPC hardware/software co-design. The Extreme-scale Simulator (xSim) is a simulation toolkit for investigating the performance of parallel applications at scale. xSim scales to millions of simulated Message Passing Interface (MPI) processes. The overhead introduced by a simulation tool is an important performance and productivity aspect. This paper documents two improvements to xSim: (1)~a new deadlock resolution protocol to reduce the parallel discrete event simulation overhead and (2)~a new simulated MPI message matchingmore » algorithm to reduce the oversubscription management overhead. The results clearly show a significant performance improvement. The simulation overhead for running the NAS Parallel Benchmark suite was reduced from 102% to 0% for the embarrassingly parallel (EP) benchmark and from 1,020% to 238% for the conjugate gradient (CG) benchmark. xSim offers a highly accurate simulation mode for better tracking of injected MPI process failures. Furthermore, with highly accurate simulation, the overhead was reduced from 3,332% to 204% for EP and from 37,511% to 13,808% for CG.« less

Time and Space Efficient Algorithms for Two-Party Authenticated Data Structures

NASA Astrophysics Data System (ADS)

Papamanthou, Charalampos; Tamassia, Roberto

Authentication is increasingly relevant to data management. Data is being outsourced to untrusted servers and clients want to securely update and query their data. For example, in database outsourcing, a client's database is stored and maintained by an untrusted server. Also, in simple storage systems, clients can store very large amounts of data but at the same time, they want to assure their integrity when they retrieve them. In this paper, we present a model and protocol for two-party authentication of data structures. Namely, a client outsources its data structure and verifies that the answers to the queries have not been tampered with. We provide efficient algorithms to securely outsource a skip list with logarithmic time overhead at the server and client and logarithmic communication cost, thus providing an efficient authentication primitive for outsourced data, both structured (e.g., relational databases) and semi-structured (e.g., XML documents). In our technique, the client stores only a constant amount of space, which is optimal. Our two-party authentication framework can be deployed on top of existing storage applications, thus providing an efficient authentication service. Finally, we present experimental results that demonstrate the practical efficiency and scalability of our scheme.

Lightweight Provenance Service for High-Performance Computing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dai, Dong; Chen, Yong; Carns, Philip

Provenance describes detailed information about the history of a piece of data, containing the relationships among elements such as users, processes, jobs, and workflows that contribute to the existence of data. Provenance is key to supporting many data management functionalities that are increasingly important in operations such as identifying data sources, parameters, or assumptions behind a given result; auditing data usage; or understanding details about how inputs are transformed into outputs. Despite its importance, however, provenance support is largely underdeveloped in highly parallel architectures and systems. One major challenge is the demanding requirements of providing provenance service in situ. Themore » need to remain lightweight and to be always on often conflicts with the need to be transparent and offer an accurate catalog of details regarding the applications and systems. To tackle this challenge, we introduce a lightweight provenance service, called LPS, for high-performance computing (HPC) systems. LPS leverages a kernel instrument mechanism to achieve transparency and introduces representative execution and flexible granularity to capture comprehensive provenance with controllable overhead. Extensive evaluations and use cases have confirmed its efficiency and usability. We believe that LPS can be integrated into current and future HPC systems to support a variety of data management needs.« less

Comparison of neuronal spike exchange methods on a Blue Gene/P supercomputer.

PubMed

Hines, Michael; Kumar, Sameer; Schürmann, Felix

2011-01-01

For neural network simulations on parallel machines, interprocessor spike communication can be a significant portion of the total simulation time. The performance of several spike exchange methods using a Blue Gene/P (BG/P) supercomputer has been tested with 8-128 K cores using randomly connected networks of up to 32 M cells with 1 k connections per cell and 4 M cells with 10 k connections per cell, i.e., on the order of 4·10(10) connections (K is 1024, M is 1024(2), and k is 1000). The spike exchange methods used are the standard Message Passing Interface (MPI) collective, MPI_Allgather, and several variants of the non-blocking Multisend method either implemented via non-blocking MPI_Isend, or exploiting the possibility of very low overhead direct memory access (DMA) communication available on the BG/P. In all cases, the worst performing method was that using MPI_Isend due to the high overhead of initiating a spike communication. The two best performing methods-the persistent Multisend method using the Record-Replay feature of the Deep Computing Messaging Framework DCMF_Multicast; and a two-phase multisend in which a DCMF_Multicast is used to first send to a subset of phase one destination cores, which then pass it on to their subset of phase two destination cores-had similar performance with very low overhead for the initiation of spike communication. Departure from ideal scaling for the Multisend methods is almost completely due to load imbalance caused by the large variation in number of cells that fire on each processor in the interval between synchronization. Spike exchange time itself is negligible since transmission overlaps with computation and is handled by a DMA controller. We conclude that ideal performance scaling will be ultimately limited by imbalance between incoming processor spikes between synchronization intervals. Thus, counterintuitively, maximization of load balance requires that the distribution of cells on processors should not reflect neural net architecture but be randomly distributed so that sets of cells which are burst firing together should be on different processors with their targets on as large a set of processors as possible.

48 CFR 552.243-71 - Equitable Adjustments.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (exclusive of employer's overhead, profit, and any labor cost burdens carried in employer's overhead rate... condition giving rise to entitlement to an equitable adjustment, including increases or decreases to... site, unless separately itemized); (2) Labor cost broken down by trade, employer, occupation, quantity...

52. SOUTH PLANT PROCESS PIPING OVERHEAD RACK, WITH SHELL OIL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

52. SOUTH PLANT PROCESS PIPING OVERHEAD RACK, WITH SHELL OIL COMPANY FACILITIES IN BACKGROUND. VIEW TO SOUTHEAST. - Rocky Mountain Arsenal, Bounded by Ninety-sixth Avenue & Fifty-sixth Avenue, Buckley Road, Quebec Street & Colorado Highway 2, Commerce City, Adams County, CO

48 CFR 1352.215-76 - Cost or pricing data.

Code of Federal Regulations, 2014 CFR

2014-10-01

...: The offeror shall list the categories of professional or technical personnel required to perform the....—should be discussed. (3) Overhead Costs. Generally, the offeror's accounting system and estimating... in accordance with generally accepted accounting principles, will be accepted. Proposed overhead...

48 CFR 1352.215-76 - Cost or pricing data.

Code of Federal Regulations, 2011 CFR

2011-10-01

...: The offeror shall list the categories of professional or technical personnel required to perform the....—should be discussed. (3) Overhead Costs. Generally, the offeror's accounting system and estimating... in accordance with generally accepted accounting principles, will be accepted. Proposed overhead...

48 CFR 1352.215-76 - Cost or pricing data.

Code of Federal Regulations, 2010 CFR

2010-10-01

...: The offeror shall list the categories of professional or technical personnel required to perform the....—should be discussed. (3) Overhead Costs. Generally, the offeror's accounting system and estimating... in accordance with generally accepted accounting principles, will be accepted. Proposed overhead...

48 CFR 1352.215-76 - Cost or pricing data.

Code of Federal Regulations, 2013 CFR

2013-10-01

...: The offeror shall list the categories of professional or technical personnel required to perform the....—should be discussed. (3) Overhead Costs. Generally, the offeror's accounting system and estimating... in accordance with generally accepted accounting principles, will be accepted. Proposed overhead...

48 CFR 1352.215-76 - Cost or pricing data.

Code of Federal Regulations, 2012 CFR

2012-10-01

...: The offeror shall list the categories of professional or technical personnel required to perform the....—should be discussed. (3) Overhead Costs. Generally, the offeror's accounting system and estimating... in accordance with generally accepted accounting principles, will be accepted. Proposed overhead...

View east from western edge of complex. Collapsed overhead conveyor ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View east from western edge of complex. Collapsed overhead conveyor in foreground carried ganister down to the brickyard from crushing and grinding facility on the mountain. - Harbison-Walker Refractories Company, West end of Shirley Street, Mount Union, Huntingdon County, PA

Orbiter View of Curiosity From Nearly Straight Overhead

NASA Image and Video Library

2012-08-31

Details such as the shadow of the mast on NASA Mars rover Curiosity appear in an image taken Aug. 17, 2012, by the HiRISE camera on NASA Mars Reconnaissance Orbiter, from more directly overhead than previous HiRISE images of Curiosity.

Characteristics and Needs for Overhead Guide Sign Illumination from Vehicular Headlamps

DOT National Transportation Integrated Search

1999-09-01

The Federal Highway Administration (FHWA) is concerned about changes in headlamp performance of the present fleet of vehicles in the US relative to its ability to properly illuminate traffic signs, especially overhead guide signs. If this is true, ov...

Use of high intensity reflective sheeting in lieu of external lighting of overhead roadway signs.

DOT National Transportation Integrated Search

2013-06-01

Effective highway signing is an important component of driver decision making, comfort, and : safety. Like many agencies across the country, overhead sign lighting has been used by the Florida : Department of Transportation (FDOT) to improve visibili...

Cooling Computers.

ERIC Educational Resources Information Center

Birken, Marvin N.

1967-01-01

Numerous decisions must be made in the design of computer air conditioning, each determined by a combination of economics, physical, and esthetic characteristics, and computer requirements. Several computer air conditioning systems are analyzed--(1) underfloor supply and overhead return, (2) underfloor plenum and overhead supply with computer unit…

New rain shed (Building No. 241), overhead pipeline and raw ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

New rain shed (Building No. 241), overhead pipeline and raw water tank T4. Distribution pump house can be seen at the center of building. - Hawaii Volcanoes National Park Water Collection System, Hawaii Volcanoes National Park, Volcano, Hawaii County, HI

Spectroscopy on the Overhead Projector.

ERIC Educational Resources Information Center

Solomon, Sally; And Others

1994-01-01

Any overhead projector easily can be converted into a simple spectrometer by placing a piece of diffraction grating over the projecting lens. A detailed description of the apparatus and suggested spectroscopy experiments are included. Demonstrations can utilize solutions of cobalt chloride, potassium permanganate, potassium dichromate, or…

33 CFR 165.540 - Regulated Navigation Area; Cape Fear River, Northeast Cape Fear River, Wilmington, North Carolina.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Carolina Power & Light Company (CP&L) overhead power line crossing). (4) Passing Lane and Anchorage Basin... Buoy 56 (LL 30830) and approximately 590 feet downstream of the CP&L overhead power line crossing...

33 CFR 165.540 - Regulated Navigation Area; Cape Fear River, Northeast Cape Fear River, Wilmington, North Carolina.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Carolina Power & Light Company (CP&L) overhead power line crossing). (4) Passing Lane and Anchorage Basin... Buoy 56 (LL 30830) and approximately 590 feet downstream of the CP&L overhead power line crossing...

33 CFR 165.540 - Regulated Navigation Area; Cape Fear River, Northeast Cape Fear River, Wilmington, North Carolina.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Carolina Power & Light Company (CP&L) overhead power line crossing). (4) Passing Lane and Anchorage Basin... Buoy 56 (LL 30830) and approximately 590 feet downstream of the CP&L overhead power line crossing...

33 CFR 165.540 - Regulated Navigation Area; Cape Fear River, Northeast Cape Fear River, Wilmington, North Carolina.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Carolina Power & Light Company (CP&L) overhead power line crossing). (4) Passing Lane and Anchorage Basin... Buoy 56 (LL 30830) and approximately 590 feet downstream of the CP&L overhead power line crossing...

33 CFR 165.540 - Regulated Navigation Area; Cape Fear River, Northeast Cape Fear River, Wilmington, North Carolina.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Carolina Power & Light Company (CP&L) overhead power line crossing). (4) Passing Lane and Anchorage Basin... Buoy 56 (LL 30830) and approximately 590 feet downstream of the CP&L overhead power line crossing...

An assessment of alternatives to the Eichleay formula for unabsorbed overhead in delay claims : final report.

DOT National Transportation Integrated Search

1988-01-01

This report presents an assessment of the accuracy of alternatives available to calculate unabsorbed overhead in construction delay claims submitted by contractors. It reviews the alternatives available, concludes that the Eichleay method, used by ma...

BIOSPIDA: A Relational Database Translator for NCBI

PubMed Central

Hagen, Matthew S.; Lee, Eva K.

2010-01-01

As the volume and availability of biological databases continue widespread growth, it has become increasingly difficult for research scientists to identify all relevant information for biological entities of interest. Details of nucleotide sequences, gene expression, molecular interactions, and three-dimensional structures are maintained across many different databases. To retrieve all necessary information requires an integrated system that can query multiple databases with minimized overhead. This paper introduces a universal parser and relational schema translator that can be utilized for all NCBI databases in Abstract Syntax Notation (ASN.1). The data models for OMIM, Entrez-Gene, Pubmed, MMDB and GenBank have been successfully converted into relational databases and all are easily linkable helping to answer complex biological questions. These tools facilitate research scientists to locally integrate databases from NCBI without significant workload or development time. PMID:21347013

Technology Insertion-Engineering Services Process Characterization, Task Order Number 1. Volume 5. Revision A

DTIC Science & Technology

1989-12-22

and Floor Space Utilization for the Arc Weld and Heat Treat Shop," proposes that a bridge crane be installed in this area to move large heavy parts...levels. It is difficult to quantify the effects of this environment, but they certainly include increased stress and lowered productivity. 8.1.1.3...team study, under the QP4 program. While MABPSA makes some use of powered material handling equipment (forklift trucks and overhead cranes ) most

Central Campus Construction Progress

NASA Image and Video Library

2016-10-18

A large crane towers overhead as the new, seven-story headquarters building takes shape in the industrial area at NASA’s Kennedy Space Center in Florida. The 200,000-square-foot facility will anchor the spaceport’s Central Campus and house about 500 NASA civil service and contractor employees. The building will be more energy efficient than the current Headquarters building and will feature the latest in office and administrative building technology to fulfill Kennedy's role as the premiere multi-user spaceport for NASA and, increasingly, commercial entities.

Fault-tolerant clock synchronization in distributed systems

NASA Technical Reports Server (NTRS)

Ramanathan, Parameswaran; Shin, Kang G.; Butler, Ricky W.

1990-01-01

Existing fault-tolerant clock synchronization algorithms are compared and contrasted. These include the following: software synchronization algorithms, such as convergence-averaging, convergence-nonaveraging, and consistency algorithms, as well as probabilistic synchronization; hardware synchronization algorithms; and hybrid synchronization. The worst-case clock skews guaranteed by representative algorithms are compared, along with other important aspects such as time, message, and cost overhead imposed by the algorithms. More recent developments such as hardware-assisted software synchronization and algorithms for synchronizing large, partially connected distributed systems are especially emphasized.

Distributed and Modular CAN-Based Architecture for Hardware Control and Sensor Data Integration

PubMed Central

Losada, Diego P.; Fernández, Joaquín L.; Paz, Enrique; Sanz, Rafael

2017-01-01

In this article, we present a CAN-based (Controller Area Network) distributed system to integrate sensors, actuators and hardware controllers in a mobile robot platform. With this work, we provide a robust, simple, flexible and open system to make hardware elements or subsystems communicate, that can be applied to different robots or mobile platforms. Hardware modules can be connected to or disconnected from the CAN bus while the system is working. It has been tested in our mobile robot Rato, based on a RWI (Real World Interface) mobile platform, to replace the old sensor and motor controllers. It has also been used in the design of two new robots: BellBot and WatchBot. Currently, our hardware integration architecture supports different sensors, actuators and control subsystems, such as motor controllers and inertial measurement units. The integration architecture was tested and compared with other solutions through a performance analysis of relevant parameters such as transmission efficiency and bandwidth usage. The results conclude that the proposed solution implements a lightweight communication protocol for mobile robot applications that avoids transmission delays and overhead. PMID:28467381

Distributed and Modular CAN-Based Architecture for Hardware Control and Sensor Data Integration.

PubMed

Losada, Diego P; Fernández, Joaquín L; Paz, Enrique; Sanz, Rafael

2017-05-03

In this article, we present a CAN-based (Controller Area Network) distributed system to integrate sensors, actuators and hardware controllers in a mobile robot platform. With this work, we provide a robust, simple, flexible and open system to make hardware elements or subsystems communicate, that can be applied to different robots or mobile platforms. Hardware modules can be connected to or disconnected from the CAN bus while the system is working. It has been tested in our mobile robot Rato, based on a RWI (Real World Interface) mobile platform, to replace the old sensor and motor controllers. It has also been used in the design of two new robots: BellBot and WatchBot. Currently, our hardware integration architecture supports different sensors, actuators and control subsystems, such as motor controllers and inertial measurement units. The integration architecture was tested and compared with other solutions through a performance analysis of relevant parameters such as transmission efficiency and bandwidth usage. The results conclude that the proposed solution implements a lightweight communication protocol for mobile robot applications that avoids transmission delays and overhead.

Simplified Antenna Group Determination of RS Overhead Reduced Massive MIMO for Wireless Sensor Networks.

PubMed

Lee, Byung Moo

2017-12-29

Massive multiple-input multiple-output (MIMO) systems can be applied to support numerous internet of things (IoT) devices using its excessive amount of transmitter (TX) antennas. However, one of the big obstacles for the realization of the massive MIMO system is the overhead of reference signal (RS), because the number of RS is proportional to the number of TX antennas and/or related user equipments (UEs). It has been already reported that antenna group-based RS overhead reduction can be very effective to the efficient operation of massive MIMO, but the method of deciding the number of antennas needed in each group is at question. In this paper, we propose a simplified determination scheme of the number of antennas needed in each group for RS overhead reduced massive MIMO to support many IoT devices. Supporting many distributed IoT devices is a framework to configure wireless sensor networks. Our contribution can be divided into two parts. First, we derive simple closed-form approximations of the achievable spectral efficiency (SE) by using zero-forcing (ZF) and matched filtering (MF) precoding for the RS overhead reduced massive MIMO systems with channel estimation error. The closed-form approximations include a channel error factor that can be adjusted according to the method of the channel estimation. Second, based on the closed-form approximation, we present an efficient algorithm determining the number of antennas needed in each group for the group-based RS overhead reduction scheme. The algorithm depends on the exact inverse functions of the derived closed-form approximations of SE. It is verified with theoretical analysis and simulation that the proposed algorithm works well, and thus can be used as an important tool for massive MIMO systems to support many distributed IoT devices.

Simplified Antenna Group Determination of RS Overhead Reduced Massive MIMO for Wireless Sensor Networks

PubMed Central

2017-01-01

Massive multiple-input multiple-output (MIMO) systems can be applied to support numerous internet of things (IoT) devices using its excessive amount of transmitter (TX) antennas. However, one of the big obstacles for the realization of the massive MIMO system is the overhead of reference signal (RS), because the number of RS is proportional to the number of TX antennas and/or related user equipments (UEs). It has been already reported that antenna group-based RS overhead reduction can be very effective to the efficient operation of massive MIMO, but the method of deciding the number of antennas needed in each group is at question. In this paper, we propose a simplified determination scheme of the number of antennas needed in each group for RS overhead reduced massive MIMO to support many IoT devices. Supporting many distributed IoT devices is a framework to configure wireless sensor networks. Our contribution can be divided into two parts. First, we derive simple closed-form approximations of the achievable spectral efficiency (SE) by using zero-forcing (ZF) and matched filtering (MF) precoding for the RS overhead reduced massive MIMO systems with channel estimation error. The closed-form approximations include a channel error factor that can be adjusted according to the method of the channel estimation. Second, based on the closed-form approximation, we present an efficient algorithm determining the number of antennas needed in each group for the group-based RS overhead reduction scheme. The algorithm depends on the exact inverse functions of the derived closed-form approximations of SE. It is verified with theoretical analysis and simulation that the proposed algorithm works well, and thus can be used as an important tool for massive MIMO systems to support many distributed IoT devices. PMID:29286339

A study of the use of abstract types for the representation of engineering units in integration and test applications

NASA Technical Reports Server (NTRS)

Johnson, Charles S.

1986-01-01

Physical quantities using various units of measurement can be well represented in Ada by the use of abstract types. Computation involving these quantities (electric potential, mass, volume) can also automatically invoke the computation and checking of some of the implicitly associable attributes of measurements. Quantities can be held internally in SI units, transparently to the user, with automatic conversion. Through dimensional analysis, the type of the derived quantity resulting from a computation is known, thereby allowing dynamic checks of the equations used. The impact of the possible implementation of these techniques in integration and test applications is discussed. The overhead of computing and transporting measurement attributes is weighed against the advantages gained by their use. The construction of a run time interpreter using physical quantities in equations can be aided by the dynamic equation checks provided by dimensional analysis. The effects of high levels of abstraction on the generation and maintenance of software used in integration and test applications are also discussed.

An ultra low-power CMOS automatic action potential detector.

PubMed

Gosselin, Benoit; Sawan, Mohamad

2009-08-01

We present a low-power complementary metal-oxide semiconductor (CMOS) analog integrated biopotential detector intended for neural recording in wireless multichannel implants. The proposed detector can achieve accurate automatic discrimination of action potential (APs) from the background activity by means of an energy-based preprocessor and a linear delay element. This strategy improves detected waveforms integrity and prompts for better performance in neural prostheses. The delay element is implemented with a low-power continuous-time filter using a ninth-order equiripple allpass transfer function. All circuit building blocks use subthreshold OTAs employing dedicated circuit techniques for achieving ultra low-power and high dynamic range. The proposed circuit function in the submicrowatt range as the implemented CMOS 0.18- microm chip dissipates 780 nW, and it features a size of 0.07 mm(2). So it is suitable for massive integration in a multichannel device with modest overhead. The fabricated detector succeeds to automatically detect APs from underlying background activity. Testbench validation results obtained with synthetic neural waveforms are presented.

Automatic Generation of Cycle-Approximate TLMs with Timed RTOS Model Support

NASA Astrophysics Data System (ADS)

Hwang, Yonghyun; Schirner, Gunar; Abdi, Samar

This paper presents a technique for automatically generating cycle-approximate transaction level models (TLMs) for multi-process applications mapped to embedded platforms. It incorporates three key features: (a) basic block level timing annotation, (b) RTOS model integration, and (c) RTOS overhead delay modeling. The inputs to TLM generation are application C processes and their mapping to processors in the platform. A processor data model, including pipelined datapath, memory hierarchy and branch delay model is used to estimate basic block execution delays. The delays are annotated to the C code, which is then integrated with a generated SystemC RTOS model. Our abstract RTOS provides dynamic scheduling and inter-process communication (IPC) with processor- and RTOS-specific pre-characterized timing. Our experiments using a MP3 decoder and a JPEG encoder show that timed TLMs, with integrated RTOS models, can be automatically generated in less than a minute. Our generated TLMs simulated three times faster than real-time and showed less than 10% timing error compared to board measurements.

84. GRINDING ROOM, LOOKING EAST. NOTE OVERHEAD BRIDGE CRANE RIDING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

84. GRINDING ROOM, LOOKING EAST. NOTE OVERHEAD BRIDGE CRANE RIDING ON STEEL RAILS SUPPORTED BY WOODEN BEAMS AND CYCLONE CLASSIFIER IN CENTER. AT RIGHT IS TOP PORTION OF FLASH FLOTATION CELL. - Shenandoah-Dives Mill, 135 County Road 2, Silverton, San Juan County, CO

Oblique view to the northwest detailing four overhead rolling doors ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Oblique view to the northwest detailing four overhead rolling doors on the northeast elevation - Over-the-Horizon Backscatter Radar Network, Mountain Home Air Force Operations Building, On Desert Street at 9th Avenue Mountain Home Air Force Base, Mountain Home, Elmore County, ID

48 CFR 3416.702 - Basic agreements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Basic agreements. 3416.702... CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Agreements 3416.702 Basic agreements. (a)-(d) [Reserved] (e) Negotiated overhead rates. Basic agreements may include negotiated overhead rates for cost...

13. Interior view, grain tanks (bins). Barrel view of overhead ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Interior view, grain tanks (bins). Barrel view of overhead (fill) conveyor gallery bridge extending through tops of tanks just below roofs. Grain tripper straddles belt conveyor at mid-view. - Saint Anthony Elevator No. 3, 620 Malcom Avenue, Southeast, Minneapolis, Hennepin County, MN

Specification-based Error Recovery: Theory, Algorithms, and Usability

DTIC Science & Technology

2013-02-01

transmuting the specification to an implementation at run-time and reducing the performance overhead. A suite of techniques and tools were designed...in the specification, thereby transmuting the specification to an implementation at run-time and reducing the perfor- mance overhead. A suite of

Design Considerations for Abrasive Blast Rooms and Recovery Systems

DTIC Science & Technology

2010-02-01

COLUMN BOLT – ALLOWS FOR WIDER ENCLOSURES – STRONG ENOUGH TO SUPPORT MONORAIL Flange Bolt Room Column Bolt Room • Structural steel framework...OVERHEAD MONORAILS • EXTERIOR WORK STATIONS • TURNTABLES • HORIZONTAL ROTATION DEVICES OVERHEAD MONORAIL Workpiece Handling • Powered horizontal rotation

142. OVERHEAD CRANES ON SOUTH WALL AND CEILING OF AGENA ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

142. OVERHEAD CRANES ON SOUTH WALL AND CEILING OF AGENA TRANSFER AREA SHELTER (117A), LSB (BLDG. 770). FORMERLY USED FOR VEHICLE TRANSFER. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 West, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

30 CFR 220.012 - Overhead allowance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Overhead allowance. 220.012 Section 220.012 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR MINERALS REVENUE MANAGEMENT ACCOUNTING PROCEDURES FOR DETERMINING NET PROFIT SHARE PAYMENT FOR OUTER CONTINENTAL SHELF OIL AND GAS LEASES...

73. TORPEDO WORK SHOP FORWARD LOOKING AFT SHOWING TORPEDO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

73. TORPEDO WORK SHOP - FORWARD LOOKING AFT SHOWING TORPEDO ELEVATOR, HIGH PRESSURE AIR REDUCING STATION, SCUTTLEBUTT, TORPEDO AFTERBODY WORKSHOP, OVERHEAD CHAIN MOIST AND RAIL SYSTEM AND OVERHEAD SPRINKLER SYSTEM. - U.S.S. HORNET, Puget Sound Naval Shipyard, Sinclair Inlet, Bremerton, Kitsap County, WA

TRANSLATION TO PORTUGUESE LANGUAGE AND CROSS-CULTURAL ADAPTATION OF THE MODIFIED ROWE SCORE FOR OVERHEAD ATHLETES

PubMed Central

Marcondes, Freddy Beretta; de Vasconcelos, Rodrigo Antunes; Marchetto, Adriano; de Andrade, André Luis Lugnani; Filho, Américo Zoppi; Etchebehere, Maurício

2015-01-01

Objetctive: Study was to translate and culturally adapt the modified Rowe score for overhead athletes. Methods: The translation and cultural adaptation process initially involved the stages of translation, synthesis, back-translation, and revision by the Translation Group. It was than created the pre-final version of the questionnaire, being the areas “function” and “pain” applied to 20 athletes that perform overhead movements and that suffered SLAP lesions in the dominant shoulder and the areas “active compression test and anterior apprehension test” and “motion” were applied to 15 health professionals. Results: During the translation process there were made little modifications in the questionnaire in order to adapt it to Brazilian culture, without changing the semantics and the idiomatic concept originally described. Conclusion: The questionnaire was easily understood by the subjects of the study, being possible to obtain the Brazilian version of the modified Rowe score for overhead athletes that underwent surgical treatment of the SLAP lesion. PMID:27047903

Compilation time analysis to minimize run-time overhead in preemptive scheduling on multiprocessors

NASA Astrophysics Data System (ADS)

Wauters, Piet; Lauwereins, Rudy; Peperstraete, J.

1994-10-01

This paper describes a scheduling method for hard real-time Digital Signal Processing (DSP) applications, implemented on a multi-processor. Due to the very high operating frequencies of DSP applications (typically hundreds of kHz) runtime overhead should be kept as small as possible. Because static scheduling introduces very little run-time overhead it is used as much as possible. Dynamic pre-emption of tasks is allowed if and only if it leads to better performance in spite of the extra run-time overhead. We essentially combine static scheduling with dynamic pre-emption using static priorities. Since we are dealing with hard real-time applications we must be able to guarantee at compile-time that all timing requirements will be satisfied at run-time. We will show that our method performs at least as good as any static scheduling method. It also reduces the total amount of dynamic pre-emptions compared with run time methods like deadline monotonic scheduling.

Resource optimized TTSH-URA for multimedia stream authentication in swallowable-capsule-based wireless body sensor networks.

PubMed

Wang, Wei; Wang, Chunqiu; Zhao, Min

2014-03-01

To ease the burdens on the hospitalization capacity, an emerging swallowable-capsule technology has evolved to serve as a remote gastrointestinal (GI) disease examination technique with the aid of the wireless body sensor network (WBSN). Secure multimedia transmission in such a swallowable-capsule-based WBSN faces critical challenges including energy efficiency and content quality guarantee. In this paper, we propose a joint resource allocation and stream authentication scheme to maintain the best possible video quality while ensuring security and energy efficiency in GI-WBSNs. The contribution of this research is twofold. First, we establish a unique signature-hash (S-H) diversity approach in the authentication domain to optimize video authentication robustness and the authentication bit rate overhead over a wireless channel. Based on the full exploration of S-H authentication diversity, we propose a new two-tier signature-hash (TTSH) stream authentication scheme to improve the video quality by reducing authentication dependence overhead while protecting its integrity. Second, we propose to combine this authentication scheme with a unique S-H oriented unequal resource allocation (URA) scheme to improve the energy-distortion-authentication performance of wireless video delivery in GI-WBSN. Our analysis and simulation results demonstrate that the proposed TTSH with URA scheme achieves considerable gain in both authenticated video quality and energy efficiency.

Longitudinal acceleration tests of overhead luggage bins and auxiliary fuel tank in a transport airplane airframe section

DOT National Transportation Integrated Search

1999-06-01

This report contains the description and test results of overhead stowage bin calibrations and longitudinal impact testing of a 10-foot transport airframe section conducted at the Transportation Research Center Inc. (TRC). The purpose of the tests wa...

23 CFR 140.907 - Overhead and indirect construction costs.

Code of Federal Regulations, 2010 CFR

2010-04-01

... accounting principles; (2) The costs included in the distribution are limited to costs actually incurred by...), part 31, Contract Cost Principles and Procedures, relating to contracts with commercial organizations... 23 Highways 1 2010-04-01 2010-04-01 false Overhead and indirect construction costs. 140.907...

13. Emplacement no. 2, overhead view of counterweight well, showing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

13. Emplacement no. 2, overhead view of counterweight well, showing channel for gun motor cable and bolt plates upon which base ring of gun carriage was mounted - Fort Wadsworth Battery Romeyn B. Ayers, South side of Ayers Road, Staten Island, Rosebank, Richmond County, NY

30 CFR 56.12045 - Overhead powerlines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Overhead powerlines. 56.12045 Section 56.12045 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity § 56.12045...

30 CFR 56.12045 - Overhead powerlines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Overhead powerlines. 56.12045 Section 56.12045 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity § 56.12045...

30 CFR 56.12045 - Overhead powerlines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Overhead powerlines. 56.12045 Section 56.12045 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity § 56.12045...

30 CFR 56.12045 - Overhead powerlines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Overhead powerlines. 56.12045 Section 56.12045 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity § 56.12045...

30 CFR 56.12045 - Overhead powerlines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Overhead powerlines. 56.12045 Section 56.12045 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Electricity § 56.12045...

Overhead Projector Demonstrations: Some Ideas from the Past.

ERIC Educational Resources Information Center

Kolb, Doris

1987-01-01

Describes nine chemistry demonstrations that can be done using an overhead projector. Includes demonstrations on common ion effect, crystal formation from supersaturated solutions, making iron positive with nitric acid, optical activity, carbon dioxide in human breath, amphoteric hydroxides, the surface tension of mercury, and natural acid-base…

5. OVERHEAD VIEW OF GENE CAMP LOOKING SOUTH. GENE PUMP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. OVERHEAD VIEW OF GENE CAMP LOOKING SOUTH. GENE PUMP PLANT IS AT CENTER WITH ADMINISTRATIVE COMPLEX IN FOREGROUND AND RESIDENTIAL AREA BEYOND PLANT. - Gene Pump Plant, South of Gene Wash Reservoir, 2 miles west of Whitsett Pump Plant, Parker Dam, San Bernardino County, CA

STOCK YARD LOOKING SOUTHEAST SHOWING OVERHEAD YARD CRANE RAIL, THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

STOCK YARD LOOKING SOUTHEAST SHOWING OVERHEAD YARD CRANE RAIL, THE MALLEABLE CUPOLAS AND EMISSION RECOVERY SYSTEM, OLD SHED ROOF THAT COVERED THE EARLIER MALLEABLE CUPOLA CHARGING CRANE, MALLEABLE FOUNDRY, AND POLLUTION CONTROL BAGHOUSE. - Stockham Pipe & Fittings Company, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

The Effect of Glenohumeral Internal-Rotation Deficit on Functional Rotator-Strength Ratio in Adolescent Overhead Athletes.

PubMed

Guney, Hande; Harput, Gulcan; Colakoglu, Filiz; Baltaci, Gul

2016-02-01

Glenohumeral (GH) internal-rotation deficit (GIRD) and lower eccentric external-rotator (ER) to concentric internal-rotator (IR) strength (ER:IR) ratio have been documented as risk factors for shoulder injuries, but there is no information on whether GIRD has an adverse effect on ER:IR ratio in adolescent overhead athletes. The aim of this study was to investigate the effects of GIRD on functional ER:IR ratio of the adolescent overhead athletes. Cross-sectional study. University research laboratory. 52 adolescent overhead athletes. To determine GIRD, the range of GH IR and ER motion was measured with a digital inclinometer. An isokinetic dynamometer was used to assess eccentric and concentric IR and ER muscle strength of the dominant and nondominant shoulders. One-way ANCOVA where sport type was set as a covariate was used to analyze the difference between athletes with and without GIRD. After standardized examinations of all shoulders, the athletes were divided into 2 groups, shoulders with (n = 27) and without GIRD (n = 25). There was a significant difference between groups in functional ER:IR ratio (P < .001). Athletes with GIRD had lower ER:IR ratio (0.56) than athletes without GIRD (0.83). As GIRD has an adverse effect on functional ratio of the shoulder-rotator muscles, interventions for adolescent overhead athletes should include improving GH-rotation range of motion.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Lingda; Hayes, Ari; Song, Shuaiwen

Modern GPUs employ cache to improve memory system efficiency. However, large amount of cache space is underutilized due to irregular memory accesses and poor spatial locality which exhibited commonly in GPU applications. Our experiments show that using smaller cache lines could improve cache space utilization, but it also frequently suffers from significant performance loss by introducing large amount of extra cache requests. In this work, we propose a novel cache design named tag-split cache (TSC) that enables fine-grained cache storage to address the problem of cache space underutilization while keeping memory request number unchanged. TSC divides tag into two partsmore » to reduce storage overhead, and it supports multiple cache line replacement in one cycle.« less

The Integration of CloudStack and OCCI/OpenNebula with DIRAC

NASA Astrophysics Data System (ADS)

Méndez Muñoz, Víctor; Fernández Albor, Víctor; Graciani Diaz, Ricardo; Casajús Ramo, Adriàn; Fernández Pena, Tomás; Merino Arévalo, Gonzalo; José Saborido Silva, Juan

2012-12-01

The increasing availability of Cloud resources is arising as a realistic alternative to the Grid as a paradigm for enabling scientific communities to access large distributed computing resources. The DIRAC framework for distributed computing is an easy way to efficiently access to resources from both systems. This paper explains the integration of DIRAC with two open-source Cloud Managers: OpenNebula (taking advantage of the OCCI standard) and CloudStack. These are computing tools to manage the complexity and heterogeneity of distributed data center infrastructures, allowing to create virtual clusters on demand, including public, private and hybrid clouds. This approach has required to develop an extension to the previous DIRAC Virtual Machine engine, which was developed for Amazon EC2, allowing the connection with these new cloud managers. In the OpenNebula case, the development has been based on the CernVM Virtual Software Appliance with appropriate contextualization, while in the case of CloudStack, the infrastructure has been kept more general, which permits other Virtual Machine sources and operating systems being used. In both cases, CernVM File System has been used to facilitate software distribution to the computing nodes. With the resulting infrastructure, the cloud resources are transparent to the users through a friendly interface, like the DIRAC Web Portal. The main purpose of this integration is to get a system that can manage cloud and grid resources at the same time. This particular feature pushes DIRAC to a new conceptual denomination as interware, integrating different middleware. Users from different communities do not need to care about the installation of the standard software that is available at the nodes, nor the operating system of the host machine which is transparent to the user. This paper presents an analysis of the overhead of the virtual layer, doing some tests to compare the proposed approach with the existing Grid solution. License Notice: Published under licence in Journal of Physics: Conference Series by IOP Publishing Ltd.

19. Interior view showing flight simulator partition and rear overhead ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. Interior view showing flight simulator partition and rear overhead door, dock no. 493. View to south. - Offutt Air Force Base, Looking Glass Airborne Command Post, Nose Docks, On either side of Hangar Access Apron at Northwest end of Project Looking Glass Historic District, Bellevue, Sarpy County, NE

Determination of remaining fatigue life of welded stud details on overhead aluminum sign panels in Virginia.

DOT National Transportation Integrated Search

2005-01-01

Some overhead highways signs in Virginia using a specific welded threaded stud and clip connection have failed while in service. From inspection of the signs it was determined that the failure was caused by fatigue of the weld connecting the threaded...

A Simple Polarimeter and Experiments Utilizing an Overhead Projector.

ERIC Educational Resources Information Center

Dorn, H. C.; And Others

1984-01-01

Although polarimeters that illustrate rotation of plane-polarized light by chiral solutions have been previously described, the polarimeter described in this paper has certain advantages when used in conjunction with an overhead projector. Instructions for constructing this polarimeter and its use in demonstrating the optical activity of sugars…

76 FR 72461 - Proposed Extension of Existing Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-23

... size, employee benefits and overhead. In addition, approximately 1,500 broker-dealers must comply with... work-year and multiplied by 2.93 to account for bonuses, firm size, employee benefits and overhead. The... techniques or other forms of information technology. Consideration will be given to comments and suggestions...

76 FR 10476 - Special Conditions: Boeing Model 787-8 Airplane; Overhead Crew-Rest Compartment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-25

...\\ in interior volume, the design must ensure the ability to contain a fire likely to occur within the... or unusual design features associated with installation of an overhead crew-rest (OCR) compartment... this design feature. These special conditions contain the additional safety standards that the...

Viewing Vertical Objects with an Overhead Projector.

ERIC Educational Resources Information Center

Wild, R. L.

1988-01-01

Discusses the use of an overhead projector for the deflection of a vertical image to a screen. Describes three demonstrations: magnetizing of a steel ball bearing and paper clip; convection currents of a hot liquid within a cold liquid; and oscillation of concentrated salt solution into fresh water. (YP)

General view of the flight deck of the orbiter Discovery ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

General view of the flight deck of the orbiter Discovery looking forward and overhead at the overhead instrumentation and control panels. This view was taken at Kennedy Space Center. - Space Transportation System, Orbiter Discovery (OV-103), Lyndon B. Johnson Space Center, 2101 NASA Parkway, Houston, Harris County, TX

49 CFR 214.515 - Overhead covers for existing on-track roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... maintenance machines. 214.515 Section 214.515 Transportation Other Regulations Relating to Transportation... Roadway Maintenance Machines and Hi-Rail Vehicles § 214.515 Overhead covers for existing on-track roadway maintenance machines. (a) For those existing on-track roadway maintenance machines either currently or...

The Overhead Projector in the Mathematics Classroom.

ERIC Educational Resources Information Center

Lenchner, George

The first section of this pamphlet illustrates and describes the overhead projector, and discusses several of its advantages over other projection devises, including its simplicity of operation, conservation of class time, dynamic effects, image size, etc. The second section describes in some detail materials and methods used to make visuals, then…

30 CFR 77.203 - Use of material or equipment overhead; safeguards.

Code of Federal Regulations, 2010 CFR

2010-07-01

...; safeguards. 77.203 Section 77.203 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS...; safeguards. Where overhead repairs are being made at surface installations and equipment or material is taken...

48 CFR 3452.216-71 - Negotiated overhead rates-fixed.

Code of Federal Regulations, 2010 CFR

2010-10-01

... acceptability of cost allocation methods shall be determined in accordance with part 31 of the Federal... different period, for which the rates apply, and (4) the specific items treated as direct costs or any changes in the items previously agreed to be direct costs. (e) Pending establishment of fixed overhead...

Effects of rotation on the nighttime brightness of overhead highway signs utilizing high intensity sheeting.

DOT National Transportation Integrated Search

1974-01-01

As an initial step in the establishment of guidelines for the use of high intensity sheeting on overhead signs, a pilot study was made to investigate the effect of rotation on the average nighttime brightness of signs utilizing this material. Rotatio...

STS-98 U.S. Lab payload is moved to stand for weight determination

NASA Technical Reports Server (NTRS)

2000-01-01

KENNEDY SPACE CENTER, Fla. -- In the Space Station Processing Facility, the 'key' to the U.S. Laboratory Destiny is officially handed over to NASA during a brief ceremony while workers look on. Suspended overhead is the laboratory, being moved to the Launch Package Integration Stand (LPIS) for a weight and center of gravity determination. Behind the workers at left is the Joint Airlock Module. Destiny is the payload aboard Space Shuttle Atlantis on mission STS-98 to the International Space Station. The lab is fitted with five system racks and will already have experiments installed inside for the flight. The launch is scheduled for January 2001.

STS-98 U.S. Lab payload is moved to stand for weight determination

NASA Technical Reports Server (NTRS)

2000-01-01

KENNEDY SPACE CENTER, Fla. -- In its overhead passage down the Space Station Processing Facility, the U.S. Laboratory Destiny travels past the Multi-Purpose Logistics Module Leonardo. Both are elements in the construction of the International Space Station. The lab is being moved to the Launch Package Integration Stand (LPIS) for a weight and center of gravity determination. Destiny is the payload aboard Space Shuttle Atlantis on mission STS-98 to the Space Station. The lab is fitted with five system racks and will already have experiments installed inside for the flight. The launch is scheduled for January 2001.

STS-110 payload S0 Truss is moved to payload canister in O&C

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- In the Operations and Checkout Building, an overhead crane carries the Integrated Truss Structure S0 to the payload canister which will transport it to the launch pad for mission STS-110. Seen below the truss is the Multi-Purpose Logistics Module Donatello, currently not in use. The S0 truss will be part of the payload on Space Shuttle Atlantis. The S0 truss will be attached to the U.S. Lab, 'Destiny,' on the 11-day mission, becoming the backbone of the orbiting International Space Station (ISS). Launch is scheduled for April 4.

KSC-07pd0067

NASA Image and Video Library

2007-01-12

KENNEDY SPACE CENTER, FLA. -- In the Hazardous Processing Facility at Astrotech Space Operations, workers attach an overhead crane to the integrated THEMIS spacecraft. The carrier is being moved to a spin table for spin-balance testing. THEMIS consists of five identical probes, the largest number of scientific satellites ever launched into orbit aboard a single rocket. This unique constellation of satellites will resolve the tantalizing mystery of what causes the spectacular sudden brightening of the aurora borealis and aurora australis - the fiery skies over the Earth's northern and southern polar regions. THEMIS is scheduled to launch Feb. 15 from Cape Canaveral Air Force Station. Photo credit: NASA/George Shelton

Solar project cost report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hale, H.J.

1978-01-01

This report provides detailed cost information for the Reedy Creek Utilities solar space heating, cooling and service water heating project located in Walt Disney World, Florida. The solar energy system cools, heats and supplies service hot water for approximately 5625 ft/sup 2/ of office space in a general office building. The system was designed as an integral part of the building at the time the building was designed. The construction costs of this solar project are presented in this report. Category costs are listed by materials, direct labor, and subcontract costs. The subcontract costs include both materials, labor, overhead andmore » profit for electrical, control and other minor subcontractors.« less

Experimental evaluation of multiprocessor cache-based error recovery

NASA Technical Reports Server (NTRS)

Janssens, Bob; Fuchs, W. K.

1991-01-01

Several variations of cache-based checkpointing for rollback error recovery in shared-memory multiprocessors have been recently developed. By modifying the cache replacement policy, these techniques use the inherent redundancy in the memory hierarchy to periodically checkpoint the computation state. Three schemes, different in the manner in which they avoid rollback propagation, are evaluated. By simulation with address traces from parallel applications running on an Encore Multimax shared-memory multiprocessor, the performance effect of integrating the recovery schemes in the cache coherence protocol are evaluated. The results indicate that the cache-based schemes can provide checkpointing capability with low performance overhead but uncontrollable high variability in the checkpoint interval.

The use of optical waveguides in head up display (HUD) applications

NASA Astrophysics Data System (ADS)

Homan, Malcolm

2013-06-01

The application of optical waveguides to Head Up Displays (HUD) is an enabling technology which solves the critical issues of volume reduction (including cockpit intrusion) and mass reduction in an affordable product which retains the high performance optical capabilities associated with today's generation of digital display based HUDs. Improved operability and pilot comfort is achieved regardless of the installation by virtue of the intrinsic properties of optical waveguides and this has enabled BAE Systems Electronic Systems to develop two distinct product streams for glareshield and overhead HUD installations respectively. This paper addresses the design drivers behind the development of the next generation of Head Up Displays and their compatibility with evolving cockpit architectures and structures. The implementation of large scale optical waveguide combiners capable of matching and exceeding the display performances normally only associated with current digital display sourced HUDs has enabled BAE Systems Electronic Systems to solve the volume and installation challenges of the latest military and civil cockpits with it's LiteHUD® technology. Glareshield mounted waveguide based HUDs are compatible with the trend towards the addition of Large Area Displays (LAD) in place of the traditional multiple Head Down Displays (HDD) within military fast jet cockpits. They use an "indirect view" variant of the display which allows the amalgamation of high resolution digital display devices with the inherently small volume and low mass of the waveguide optics. This is then viewed using the more traditional technology of a conventional HUD combiner. This successful combination of technologies has resulted in the LPHUD product which is specifically designed by BAE Systems Electronic Systems to provide an ultra-low profile HUD which can be installed behind a LAD; still providing the level of performance that is at least equivalent to that of a conventional large volume glareshield mounted HUD. In many current Business Jet and Air Transport cockpits overhead mounted HUDs employ a conventional optical combiner to relay the display from a separate projector to the pilot's eyes. In BAE Systems' Electronic Systems QHUDTM configuration this combiner is replaced by the waveguide and the bulky, intrusive overhead projector completely eliminated. The result is a significant reduction in equipment volume and mass and a much greater head clearance combined with a substantially larger Head Motion Box. This latter feature is a fundamental outturn of waveguide optical solutions which removes the restrictions on pilot eye positioning associated with current conventional systems. LiteHUD®, developed by BAE Systems, Electronic Systems achieves equivalent optical performance to in-service HUDs for less cost, mass and volume.

Analysis of Operating Modes of Stand-Alone Series Controller of Power Flows for Overhead Power Transmission Lines

NASA Astrophysics Data System (ADS)

Astashev, M. G.; Panfilov, D. I.; Seregin, D. A.; Chernyshev, A. A.

2017-12-01

The features of using the bridge voltage inverter in small-size stand-alone series controllers of power flows (PFSC) for overhead power transmission lines (OPTL) are examined. The basic processes in the converter during transient and steady state modes were analyzed. The basic relations for calculating the electromagnetic processes taking into account the energy loss in the circuit and without it were received. A simulation model is proposed of a converter that makes it possible to study its operating modes during the formation of reactance introduced into the overhead power transmission line. The results of simulation of operating modes of the PFSC are presented.

A fuzzy-logic antiswing controller for three-dimensional overhead cranes.

PubMed

Cho, Sung-Kun; Lee, Ho-Hoon

2002-04-01

In this paper, a new fuzzy antiswing control scheme is proposed for a three-dimensional overhead crane. The proposed control consists of a position servo control and a fuzzy-logic control. The position servo control is used to control crane position and rope length, and the fuzzy-logic control is used to suppress load swing. The proposed control guarantees not only prompt suppression of load swing but also accurate control of crane position and rope length for simultaneous travel, traverse, and hoisting motions of the crane. Furthermore, the proposed control provides practical gain tuning criteria for easy application. The effectiveness of the proposed control is shown by experiments with a three-dimensional prototype overhead crane.

Investigation of an advanced fault tolerant integrated avionics system

NASA Technical Reports Server (NTRS)

Dunn, W. R.; Cottrell, D.; Flanders, J.; Javornik, A.; Rusovick, M.

1986-01-01

Presented is an advanced, fault-tolerant multiprocessor avionics architecture as could be employed in an advanced rotorcraft such as LHX. The processor structure is designed to interface with existing digital avionics systems and concepts including the Army Digital Avionics System (ADAS) cockpit/display system, navaid and communications suites, integrated sensing suite, and the Advanced Digital Optical Control System (ADOCS). The report defines mission, maintenance and safety-of-flight reliability goals as might be expected for an operational LHX aircraft. Based on use of a modular, compact (16-bit) microprocessor card family, results of a preliminary study examining simplex, dual and standby-sparing architectures is presented. Given the stated constraints, it is shown that the dual architecture is best suited to meet reliability goals with minimum hardware and software overhead. The report presents hardware and software design considerations for realizing the architecture including redundancy management requirements and techniques as well as verification and validation needs and methods.

KSC-00pp1682

NASA Image and Video Library

2000-11-10

In the Space Station Processing Facility, an overhead crane lifts the P6 integrated truss segment from a workstand to place it in the payload transport canister for transfer to Launch Pad 39B. There it will be placed in Endeavour’s payload bay for launch on mission STS-97. The P6 comprises Solar Array Wing-3 and the Integrated Electronic Assembly, to be installed on the International Space Station. The Station’s electrical power system will use eight photovoltaic solar arrays, each 112 feet long by 39 feet wide, to convert sunlight to electricity. The solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery. Once in orbit, astronauts will deploy the blankets to their full size. Gimbals will be used to rotate the arrays so that they will face the Sun to provide maximum power to the Space Station. Launch is scheduled Nov. 30 at 10:06 p.m. EST

KSC-00pp1683

NASA Image and Video Library

2000-11-10

In the Space Station Processing Facility, an overhead crane moves the P6 integrated truss segment to a payload transport canister for transfer to Launch Pad 39B. There it will be placed in Endeavour’s payload bay for launch on mission STS-97. The P6 comprises Solar Array Wing-3 and the Integrated Electronic Assembly, to be installed on the International Space Station. The Station’s electrical power system will use eight photovoltaic solar arrays, each 112 feet long by 39 feet wide, to convert sunlight to electricity. The solar arrays are mounted on a “blanket” that can be folded like an accordion for delivery. Once in orbit, astronauts will deploy the blankets to their full size. Gimbals will be used to rotate the arrays so that they will face the Sun to provide maximum power to the Space Station. Launch is scheduled Nov. 30 at 10:06 p.m. EST

Computer modeling and design of diagnostic workstations and radiology reading rooms

NASA Astrophysics Data System (ADS)

Ratib, Osman M.; Amato, Carlos L.; Balbona, Joseph A.; Boots, Kevin; Valentino, Daniel J.

2000-05-01

We used 3D modeling techniques to design and evaluate the ergonomics of diagnostic workstation and radiology reading room in the planning phase of building a new hospital at UCLA. Given serious space limitations, the challenge was to provide more optimal working environment for radiologists in a crowded and busy environment. A particular attention was given to flexibility, lighting condition and noise reduction in rooms shared by multiple users performing diagnostic tasks as well as regular clinical conferences. Re-engineering workspace ergonomics rely on the integration of new technologies, custom designed cabinets, indirect lighting, sound-absorbent partitioning and geometric arrangement of workstations to allow better privacy while optimizing space occupation. Innovations included adjustable flat monitors, integration of videoconferencing and voice recognition, control monitor and retractable keyboard for optimal space utilization. An overhead compartment protecting the monitors from ambient light is also used as accessory lightbox and rear-view projection screen for conferences.

Markov Chain Monte Carlo from Lagrangian Dynamics.

PubMed

Lan, Shiwei; Stathopoulos, Vasileios; Shahbaba, Babak; Girolami, Mark

2015-04-01

Hamiltonian Monte Carlo (HMC) improves the computational e ciency of the Metropolis-Hastings algorithm by reducing its random walk behavior. Riemannian HMC (RHMC) further improves the performance of HMC by exploiting the geometric properties of the parameter space. However, the geometric integrator used for RHMC involves implicit equations that require fixed-point iterations. In some cases, the computational overhead for solving implicit equations undermines RHMC's benefits. In an attempt to circumvent this problem, we propose an explicit integrator that replaces the momentum variable in RHMC by velocity. We show that the resulting transformation is equivalent to transforming Riemannian Hamiltonian dynamics to Lagrangian dynamics. Experimental results suggests that our method improves RHMC's overall computational e ciency in the cases considered. All computer programs and data sets are available online (http://www.ics.uci.edu/~babaks/Site/Codes.html) in order to allow replication of the results reported in this paper.

Designing a mathematical model for integrating dynamic cellular manufacturing into supply chain system

NASA Astrophysics Data System (ADS)

Aalaei, Amin; Davoudpour, Hamid

2012-11-01

This article presents designing a new mathematical model for integrating dynamic cellular manufacturing into supply chain system with an extensive coverage of important manufacturing features consideration of multiple plants location, multi-markets allocation, multi-period planning horizons with demand and part mix variation, machine capacity, and the main constraints are demand of markets satisfaction in each period, machine availability, machine time-capacity, worker assignment, available time of worker, production volume for each plant and the amounts allocated to each market. The aim of the proposed model is to minimize holding and outsourcing costs, inter-cell material handling cost, external transportation cost, procurement & maintenance and overhead cost of machines, setup cost, reconfiguration cost of machines installation and removal, hiring, firing and salary worker costs. Aimed to prove the potential benefits of such a design, presented an example is shown using a proposed model.

Nozzle Initiative Industry Advisory Committee on Standardization of Carbon-Phenolic Test Methods and Specifications

NASA Technical Reports Server (NTRS)

Bull, William B. (Compiler); Pinoli, Pat C. (Compiler); Upton, Cindy G. (Compiler); Day, Tony (Compiler); Hill, Keith (Compiler); Stone, Frank (Compiler); Hall, William B.

1994-01-01

This report is a compendium of the presentations of the 12th biannual meeting of the Industry Advisory Committee under the Solid Propulsion Integrity Program. A complete transcript of the welcoming talks is provided. Presentation outlines and overheads are included for the other sessions: SPIP Overview, Past, Current and Future Activity; Test Methods Manual and Video Tape Library; Air Force Developed Computer Aided Cure Program and SPC/TQM Experience; Magneto-Optical mapper (MOM), Joint Army/NASA program to assess composite integrity; Permeability Testing; Moisture Effusion Testing by Karl Fischer Analysis; Statistical Analysis of Acceptance Test Data; NMR Phenolic Resin Advancement; Constituent Testing Highlights on the LDC Optimization Program; Carbon Sulfur Study, Performance Related Testing; Current Rayon Specifications and Future Availability; RSRM/SPC Implementation; SRM Test Methods, Delta/Titan/FBM/RSRM; and Open Forum on Performance Based Acceptance Testing -- Industry Experience.

WFIRST: Exoplanet Target Selection and Scheduling with Greedy Optimization

NASA Astrophysics Data System (ADS)

Keithly, Dean; Garrett, Daniel; Delacroix, Christian; Savransky, Dmitry

2018-01-01

We present target selection and scheduling algorithms for missions with direct imaging of exoplanets, and the Wide Field Infrared Survey Telescope (WFIRST) in particular, which will be equipped with a coronagraphic instrument (CGI). Optimal scheduling of CGI targets can maximize the expected value of directly imaged exoplanets (completeness). Using target completeness as a reward metric and integration time plus overhead time as a cost metric, we can maximize the sum completeness for a mission with a fixed duration. We optimize over these metrics to create a list of target stars using a greedy optimization algorithm based off altruistic yield optimization (AYO) under ideal conditions. We simulate full missions using EXOSIMS by observing targets in this list for their predetermined integration times. In this poster, we report the theoretical maximum sum completeness, mean number of detected exoplanets from Monte Carlo simulations, and the ideal expected value of the simulated missions.

Visual Data-Analytics of Large-Scale Parallel Discrete-Event Simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, Caitlin; Carothers, Christopher D.; Mubarak, Misbah

Parallel discrete-event simulation (PDES) is an important tool in the codesign of extreme-scale systems because PDES provides a cost-effective way to evaluate designs of highperformance computing systems. Optimistic synchronization algorithms for PDES, such as Time Warp, allow events to be processed without global synchronization among the processing elements. A rollback mechanism is provided when events are processed out of timestamp order. Although optimistic synchronization protocols enable the scalability of large-scale PDES, the performance of the simulations must be tuned to reduce the number of rollbacks and provide an improved simulation runtime. To enable efficient large-scale optimistic simulations, one has tomore » gain insight into the factors that affect the rollback behavior and simulation performance. We developed a tool for ROSS model developers that gives them detailed metrics on the performance of their large-scale optimistic simulations at varying levels of simulation granularity. Model developers can use this information for parameter tuning of optimistic simulations in order to achieve better runtime and fewer rollbacks. In this work, we instrument the ROSS optimistic PDES framework to gather detailed statistics about the simulation engine. We have also developed an interactive visualization interface that uses the data collected by the ROSS instrumentation to understand the underlying behavior of the simulation engine. The interface connects real time to virtual time in the simulation and provides the ability to view simulation data at different granularities. We demonstrate the usefulness of our framework by performing a visual analysis of the dragonfly network topology model provided by the CODES simulation framework built on top of ROSS. The instrumentation needs to minimize overhead in order to accurately collect data about the simulation performance. To ensure that the instrumentation does not introduce unnecessary overhead, we perform a scaling study that compares instrumented ROSS simulations with their noninstrumented counterparts in order to determine the amount of perturbation when running at different simulation scales.« less

Discriminating Talent Identified Junior Australian Footballers Using a Fundamental Gross Athletic Movement Assessment

PubMed Central

Woods, Carl T.; Banyard, Harry G.; McKeown, Ian; Fransen, Job; Robertson, Sam

2016-01-01

Talent identification (TID) is a pertinent component of the sports sciences, affording practitioners the opportunity to target developmental interventions to a select few; optimising financial investments. However, TID is multi-componential, requiring the recognition of immediate and prospective performance. The measurement of athletic movement skill may afford practitioners insight into the latter component given its augmented relationship with functional sport specific qualities. It is currently unknown whether athletic movement skill is a discriminant quality in junior Australian football (AF). This study aimed to discriminate talent identified junior AF players from their non-talent identified counterparts using a fundamental gross athletic movement assessment. From a total of 50 under 18 (U18) AF players; two groups were classified a priori based on selection level; talent identified (n = 25; state academy representatives) and non-talent identified (n = 25; state-based competition representatives). Players performed a fundamental gross athletic movement assessment based on the Athletic Ability Assessment (AAA), consisting of an overhead squat, double lunge (left and right legs), single leg Romanian deadlift (left and right legs), and a push up (six movement criterions). Movements were scored across three assessment points using a three-point scale (resulting in a possible score of nine for each movement). A multivariate analysis of variance revealed significant between group effects on four of the six movement criterions (d = 0.56 – 0.87; p = 0.01 – 0.02). Binary logistic regression models and a receiver operating characteristic curve inspection revealed that the overhead squat score provided the greatest group discrimination (β(SE) = -0.89(0.44); p < 0.05), with a score of 4.5 classifying 64% and 88% of the talent identified and non-talent identified groups, respectively. Results support the integration of this assessment into contemporary talent identification approaches in junior AF, as it may provide coaches with insight into a juniors developmental potential. Key points On average, talent identified junior AF players possess superior athletic movement qualities relative to their non-talent identified counterparts. The integration of this gross athletic movement assessment into contemporary multidimensional approaches to talent identification may enable insight into a juniors developmental potential. The athletic qualities underpinning the production of the overhead squat movement could augment functional physical qualities in junior Australian footballers. Assessing movement competency in junior contexts may afford practitioners with the opportunity to rectify inefficient fundamental movement patterns prior to entrance into elite senior ranks. PMID:27803635

29 CFR 1926.6 - Incorporation by reference.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-mail: [email protected]; Web site: http://www.asme.org/: (1) ASME B30.2-2005, Overhead and Gantry....1501(a). (2) ANSI B30.2.0-1967, Safety Code for Overhead and Gantry Cranes, approved May 4, 1967, IBR..., Washington, DC 20210. (2) The Regional and Field Offices of the Occupational Safety and Health Administration...

Improving nitrogen fertilizer use efficiency in surface- and overhead sprinkler-irrigated cotton in the desert southwest

USDA-ARS?s Scientific Manuscript database

Nitrogen fertilizer use efficiency (NUE) is low in surface-irrigated cotton (Gossypium hirsutum L.), especially when adding N to irrigation water. A NO3 soil-test algorithm was compared with canopy reflectance-based N management with surface- overhead sprinkler-irrigation in Central AZ. The surfac...

Launcher and Transparent Air Table for Use with Overhead Projector

ERIC Educational Resources Information Center

Carr, H. Y.; and others

1969-01-01

Describes an apparatus designed for quantitative demonstrations of collision experiments. The apparatus consists of a transparent air table and a launching device for projecting two objects simultaneously. It may be used with an overhead projector. The apparatus won third prize in Demonstration Lecture Apparatus in the A.A.P.T. Apparatus…

Overhead Projection Cell for Streamline Flow

ERIC Educational Resources Information Center

Waage, Harold M.

1969-01-01

Describes the construction and operation of an overhead projection apparatus designed to demonstrate streamline flow of a liquid. The apparatus consists of a Plexiglass tank containing water in which plates forming the cell are submerged, a constant level reservoir, an overflow device and a system for marking the flow lines with a dye. (LC)

Dissolving Carboxylic Acids and Primary Amines on the Overhead Projector

ERIC Educational Resources Information Center

Solomon, Sally D.; Rutkowsky, Susan A.

2010-01-01

Liquid carboxylic acids (or primary amines) with limited solubility in water are dissolved by addition of aqueous sodium hydroxide (or hydrochloric acid) on the stage of an overhead projector using simple glassware and very small quantities of chemicals. This effective and colorful demonstration can be used to accompany discussions of the…

A Novel Transient Fault Current Sensor Based on the PCB Rogowski Coil for Overhead Transmission Lines

PubMed Central

Liu, Yadong; Xie, Xiaolei; Hu, Yue; Qian, Yong; Sheng, Gehao; Jiang, Xiuchen

2016-01-01

The accurate detection of high-frequency transient fault currents in overhead transmission lines is the basis of malfunction detection and diagnosis. This paper proposes a novel differential winding printed circuit board (PCB) Rogowski coil for the detection of transient fault currents in overhead transmission lines. The interference mechanism of the sensor surrounding the overhead transmission line is analyzed and the guideline for the interference elimination is obtained, and then a differential winding printed circuit board (PCB) Rogowski coil is proposed, where the branch and return line of the PCB coil were designed to be strictly symmetrical by using a joining structure of two semi-rings and collinear twisted pair differential windings in each semi-ring. A serial test is conducted, including the frequency response, linearity, and anti-interference performance as well as a comparison with commercial sensors. Results show that a PCB Rogowski coil has good linearity and resistance to various external magnetic field interferences, thus enabling it to be widely applied in fault-current-collecting devices. PMID:27213402

An Insight on Right of Way and its Cost for Power Transmission Cable and Conventional Overhead Transmission Lines

NASA Astrophysics Data System (ADS)

Khandelwal, P.; Pachori, A.; Khandelwal, T.

2013-12-01

This paper provides the complete information related to Right of Way (RoW) for the construction of new power transmission line (TL) in terms of present cost for overhead transmission line and underground XLPE transmission cable. The former part of the paper describes the general procedure and rules for acquisition of land for RoW by transmission asset owner (TAO) while in the later part the cost associated to acquire RoW and its impact on the cost of adjacent land have been detailed. It also discusses the actual dismantling cost including the cost of waste metal what TAO get after completion of lifecycle of TL due to increase in metal prices. In this paper cost of RoW after completion of lifecycle of TL is also highlighted. This paper compares the cost of RoW for overhead transmission line and underground XLPE transmission cable for construction of new TL. Also for old transmission infrastructure cost of RoW for change from overhead transmission line to underground XLPE transmission cable is detailed by application of replacement model.

Understanding checkpointing overheads on massive-scale systems : analysis of the IBM Blue Gene/P system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gupta, R.; Naik, H.; Beckman, P.

Providing fault tolerance in high-end petascale systems, consisting of millions of hardware components and complex software stacks, is becoming an increasingly challenging task. Checkpointing continues to be the most prevalent technique for providing fault tolerance in such high-end systems. Considerable research has focussed on optimizing checkpointing; however, in practice, checkpointing still involves a high-cost overhead for users. In this paper, we study the checkpointing overhead seen by various applications running on leadership-class machines like the IBM Blue Gene/P at Argonne National Laboratory. In addition to studying popular applications, we design a methodology to help users understand and intelligently choose anmore » optimal checkpointing frequency to reduce the overall checkpointing overhead incurred. In particular, we study the Grid-Based Projector-Augmented Wave application, the Carr-Parrinello Molecular Dynamics application, the Nek5000 computational fluid dynamics application and the Parallel Ocean Program application-and analyze their memory usage and possible checkpointing trends on 65,536 processors of the Blue Gene/P system.« less

Modeling the Virtual Machine Launching Overhead under Fermicloud

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garzoglio, Gabriele; Wu, Hao; Ren, Shangping

FermiCloud is a private cloud developed by the Fermi National Accelerator Laboratory for scientific workflows. The Cloud Bursting module of the FermiCloud enables the FermiCloud, when more computational resources are needed, to automatically launch virtual machines to available resources such as public clouds. One of the main challenges in developing the cloud bursting module is to decide when and where to launch a VM so that all resources are most effectively and efficiently utilized and the system performance is optimized. However, based on FermiCloud’s system operational data, the VM launching overhead is not a constant. It varies with physical resourcemore » (CPU, memory, I/O device) utilization at the time when a VM is launched. Hence, to make judicious decisions as to when and where a VM should be launched, a VM launch overhead reference model is needed. The paper is to develop a VM launch overhead reference model based on operational data we have obtained on FermiCloud and uses the reference model to guide the cloud bursting process.« less

Method for etherifications

DOEpatents

Jones, E.M. Jr.

1985-03-12

A method is described for producing tertiary ethers from C[sub 4] or C[sub 5] streams containing isobutene and isoamylene respectively in a process wherein a acidic cation exchange resin is used as the catalyst and as a distillation structure in a distillation reactor column, wherein the improvement is the operation of the catalytic distillation in two zones at different pressures, the first zone containing the catalyst packing and operated a higher pressure in the range of 100 to 200 psig in the case of C[sub 4] and 15 to 100 psig in the case of C[sub 5] which favors the etherification reaction and the second zone being a distillation operated at a lower pressure in the range of 0 to 100 psig in the case of C[sub 4] and 0 to 15 psig in the case of C[sub 5] wherein a first overhead from the first zone is fractionated to remove a portion of the unreacted alcohol from the first overhead and to return a condensed portion containing said alcohol to the first zone and to produce a second overhead having less alcohol than said first overhead. 3 figs.

Method for etherifications

DOEpatents

Jones, Jr., Edward M.

1985-01-01

A method for producing tertiary ethers from C.sub.4 or C.sub.5 streams containing isobutene and isoamylene respectively in a process wherein a acidic cation exchange resin is used as the catalyst and as a distillation structure in a distillation reactor column, wherein the improvement is the operation of the catalytic distillation in two zones at different pressures, the first zone containing the catalyst packing and operated a higher pressure in the range of 100 to 200 psig in the case of C.sub.4 's and 15 to 100 psig in the case of C.sub.5 's which favors the etherification reaction and the second zone being a distillation operated at a lower pressure in the range of 0 to 100 psig in the case of C.sub.4 's and 0 to 15 psig in the case of C.sub.5 's wherein a first overhead from the first zone is fractionated to remove a portion of the unreacted alcohol from the first overhead and to return a condensed portion containing said alcohol to the first zone and to produce a second overhead having less alcohol than said first overhead.

Scalable PGAS Metadata Management on Extreme Scale Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chavarría-Miranda, Daniel; Agarwal, Khushbu; Straatsma, TP

Programming models intended to run on exascale systems have a number of challenges to overcome, specially the sheer size of the system as measured by the number of concurrent software entities created and managed by the underlying runtime. It is clear from the size of these systems that any state maintained by the programming model has to be strictly sub-linear in size, in order not to overwhelm memory usage with pure overhead. A principal feature of Partitioned Global Address Space (PGAS) models is providing easy access to global-view distributed data structures. In order to provide efficient access to these distributedmore » data structures, PGAS models must keep track of metadata such as where array sections are located with respect to processes/threads running on the HPC system. As PGAS models and applications become ubiquitous on very large transpetascale systems, a key component to their performance and scalability will be efficient and judicious use of memory for model overhead (metadata) compared to application data. We present an evaluation of several strategies to manage PGAS metadata that exhibit different space/time tradeoffs. We use two real-world PGAS applications to capture metadata usage patterns and gain insight into their communication behavior.« less

Achieve Location Privacy-Preserving Range Query in Vehicular Sensing

PubMed Central

Lu, Rongxing; Ma, Maode; Bao, Haiyong

2017-01-01

Modern vehicles are equipped with a plethora of on-board sensors and large on-board storage, which enables them to gather and store various local-relevant data. However, the wide application of vehicular sensing has its own challenges, among which location-privacy preservation and data query accuracy are two critical problems. In this paper, we propose a novel range query scheme, which helps the data requester to accurately retrieve the sensed data from the distributive on-board storage in vehicular ad hoc networks (VANETs) with location privacy preservation. The proposed scheme exploits structured scalars to denote the locations of data requesters and vehicles, and achieves the privacy-preserving location matching with the homomorphic Paillier cryptosystem technique. Detailed security analysis shows that the proposed range query scheme can successfully preserve the location privacy of the involved data requesters and vehicles, and protect the confidentiality of the sensed data. In addition, performance evaluations are conducted to show the efficiency of the proposed scheme, in terms of computation delay and communication overhead. Specifically, the computation delay and communication overhead are not dependent on the length of the scalar, and they are only proportional to the number of vehicles. PMID:28786943

Achieve Location Privacy-Preserving Range Query in Vehicular Sensing.

PubMed

Kong, Qinglei; Lu, Rongxing; Ma, Maode; Bao, Haiyong

2017-08-08

Modern vehicles are equipped with a plethora of on-board sensors and large on-board storage, which enables them to gather and store various local-relevant data. However, the wide application of vehicular sensing has its own challenges, among which location-privacy preservation and data query accuracy are two critical problems. In this paper, we propose a novel range query scheme, which helps the data requester to accurately retrieve the sensed data from the distributive on-board storage in vehicular ad hoc networks (VANETs) with location privacy preservation. The proposed scheme exploits structured scalars to denote the locations of data requesters and vehicles, and achieves the privacy-preserving location matching with the homomorphic Paillier cryptosystem technique. Detailed security analysis shows that the proposed range query scheme can successfully preserve the location privacy of the involved data requesters and vehicles, and protect the confidentiality of the sensed data. In addition, performance evaluations are conducted to show the efficiency of the proposed scheme, in terms of computation delay and communication overhead. Specifically, the computation delay and communication overhead are not dependent on the length of the scalar, and they are only proportional to the number of vehicles.

On-demand information retrieval in sensor networks with localised query and energy-balanced data collection.

PubMed

Teng, Rui; Zhang, Bing

2011-01-01

On-demand information retrieval enables users to query and collect up-to-date sensing information from sensor nodes. Since high energy efficiency is required in a sensor network, it is desirable to disseminate query messages with small traffic overhead and to collect sensing data with low energy consumption. However, on-demand query messages are generally forwarded to sensor nodes in network-wide broadcasts, which create large traffic overhead. In addition, since on-demand information retrieval may introduce intermittent and spatial data collections, the construction and maintenance of conventional aggregation structures such as clusters and chains will be at high cost. In this paper, we propose an on-demand information retrieval approach that exploits the name resolution of data queries according to the attribute and location of each sensor node. The proposed approach localises each query dissemination and enable localised data collection with maximised aggregation. To illustrate the effectiveness of the proposed approach, an analytical model that describes the criteria of sink proxy selection is provided. The evaluation results reveal that the proposed scheme significantly reduces energy consumption and improves the balance of energy consumption among sensor nodes by alleviating heavy traffic near the sink.

Optical Modification of Casimir Forces for Improved Function of Micro-and Nano-Scale Devices

NASA Technical Reports Server (NTRS)

Strekalov, Dmitry V.; Yu, Nan

2010-01-01

Recently, there has been a considerable effort to study the Casimir and van der Waals forces, enabled by the improved ability to measure small forces near surfaces. Because of the continuously growing role of micro- and nanomechanical devices, the focus of this activity has shifted towards the ability to control these forces. Possible approaches to manipulating the Casimir force include development of composite materials, engineered nanostructures, mixed-phase materials, or active elements. So far, practical success has been limited. The role of geometrical factors in the Casimir force is significant. It is known, for example, that the Casimir force between two spherical shells enclosed one into the other is repulsive instead of normal attractive. Unfortunately, nanosurfaces with this topology are very difficult to make. A more direct approach to manipulating and neutralizing the Casimir force is using external mechanical or electromagnetic forces. Unfortunately, the technological overhead of such an approach is quite large. Using electromagnetic compensation instead of mechanical will considerably reduce this overhead and at the same time provide the degree of control over the Casimir force that mechanical springs cannot provide. A mechanical analog behind Casimir forces is shown.

Modelling and simulation techniques for membrane biology.

PubMed

Burrage, Kevin; Hancock, John; Leier, André; Nicolau, Dan V

2007-07-01

One of the most important aspects of Computational Cell Biology is the understanding of the complicated dynamical processes that take place on plasma membranes. These processes are often so complicated that purely temporal models cannot always adequately capture the dynamics. On the other hand, spatial models can have large computational overheads. In this article, we review some of these issues with respect to chemistry, membrane microdomains and anomalous diffusion and discuss how to select appropriate modelling and simulation paradigms based on some or all the following aspects: discrete, continuous, stochastic, delayed and complex spatial processes.

A numerical method for solving systems of linear ordinary differential equations with rapidly oscillating solutions

NASA Technical Reports Server (NTRS)

Bernstein, Ira B.; Brookshaw, Leigh; Fox, Peter A.

1992-01-01

The present numerical method for accurate and efficient solution of systems of linear equations proceeds by numerically developing a set of basis solutions characterized by slowly varying dependent variables. The solutions thus obtained are shown to have a computational overhead largely independent of the small size of the scale length which characterizes the solutions; in many cases, the technique obviates series solutions near singular points, and its known sources of error can be easily controlled without a substantial increase in computational time.

Return to Preinjury Levels of Participation After Superior Labral Repair in Overhead Athletes: A Systematic Review

PubMed Central

Sciascia, Aaron; Myers, Natalie; Kibler, W. Ben; Uhl, Timothy L.

2015-01-01

Context Athletes often preoperatively weigh the risks and benefits of electing to undergo an orthopaedic procedure to repair damaged tissue. A common concern for athletes is being able to return to their maximum levels of competition after shoulder surgery, whereas clinicians struggle with the ability to provide a consistent prognosis of successful return to participation after surgery. The variation in study details and rates of return in the existing literature have not supplied clinicians with enough evidence to give overhead athletes adequate information regarding successful return to participation when deciding to undergo shoulder surgery. Objective To investigate the odds of overhead athletes returning to preinjury levels of participation after arthroscopic superior labral repair. Data Sources The CINAHL, MEDLINE, and SPORTDiscus databases from 1972 to 2013. Study Selection The criteria for article selection were (1) The study was written in English. (2) The study reported surgical repair of an isolated superior labral injury or a superior labral injury with soft tissue debridement. (3) The study involved overhead athletes equal to or less than 40 years of age. (4) The study assessed return to the preinjury level of participation. Data Extraction We critically reviewed articles for quality and bias and calculated and compared odds ratios for return to full participation for dichotomous populations or surgical procedures. Data Synthesis Of 215 identified articles, 11 were retained: 5 articles about isolated superior labral repair and 6 articles about labral repair with soft tissue debridement. The quality range was 11 to 17 (42% to 70%) of a possible 24 points. Odds ratios could be generated for 8 of 11 studies. Nonbaseball, nonoverhead, and nonthrowing athletes had a 2.3 to 5.8 times greater chance of full return to participation than overhead/throwing athletes after isolated superior labral repair. Similarly, nonoverhead athletes had 1.5 to 3.5 times greater odds for full return than overhead athletes after labral repair with soft tissue debridement. In 1 study, researchers compared surgical procedures and found that overhead athletes who underwent isolated superior labral repair were 28 times more likely to return to full participation than those who underwent concurrent labral repair and soft tissue debridement (P < .05). Conclusions The rate of return to participation after shoulder surgery within the literature is inconsistent. Odds of returning to preinjury levels of participation after arthroscopic superior labral repair with or without soft tissue debridement are consistently lower in overhead/throwing athletes than in nonoverhead/nonthrowing athletes. The variable rates of return within each group could be due to multiple confounding variables not consistently accounted for in the articles. PMID:25946167

78 FR 283 - 2013 Rate Changes for the Basetime, Overtime, Holiday, and Laboratory Services Rates

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-03

... rate, plus the allowance for bad debt rate. The calculation for the 2013 basetime rate per hour per...)) = $28.36 + $8.96(benefits rate) + $.70 (travel and operating rate) + $17.15 (overhead rate) + $.01 (bad... travel and operating rate, plus the overhead rate, plus the allowance for bad debt rate. The calculation...

76 FR 80326 - 2012 Rate Changes for the Basetime, Overtime, Holiday, and Laboratory Services Rates

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

..., plus the travel and operating rate, plus the overhead rate, plus the allowance for bad debt rate. The... and operating rate) + $16.68 (overhead rate) + $.02 (bad debt allowance rate) = $54.24. Overtime Rate... rate, plus the allowance for bad debt rate. The calculation for the 2012 overtime rate per hour per...

Using the Overhead Projector as a Light Source for Physics Demonstrations

ERIC Educational Resources Information Center

Mak, Se-Yuen

2006-01-01

This article illustrates how the overhead projector can be used as a light source in some peculiar ways for physics demonstrations. Five examples are included: (1) Study of chromatic aberration; (2) Making giant Newton's rings; (3) Comparison of the rate of heat absorption by different surfaces; (4) Demonstration of greenhouse effect; and (5)…

The Use of the Overhead Projector in Teaching Composition.

ERIC Educational Resources Information Center

Bissex, Henry

The overhead projector, used as a controllable blackboard or bulletin board in the teaching of writing, extends the range of teaching techniques so that an instructor may (1) prepare, in advance, handwritten sheets of film--test questions, pupils' sentences, quotations, short poems--to be shown in any order or form; (2) use pictures, graphics, or…

Growth, gas exchange, foliar nitrogen content, and water use of subirrigated and overhead irrigated Populus tremuloides Michx. seedlings

Treesearch

Anthony S. Davis; Matthew M. Aghai; Jeremiah R. Pinto; Kent G. Apostal

2011-01-01

Because limitations on water used by container nurseries has become commonplace, nursery growers will have to improve irrigation management. Subirrigation systems may provide an alternative to overhead irrigation systems by mitigating groundwater pollution and excessive water consumption. Seedling growth, gas exchange, leaf nitrogen (N) content, and water use were...

46 CFR 76.30-10 - Location and spacing of tubing.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Location and spacing of tubing. 76.30-10 Section 76.30... PROTECTION EQUIPMENT Pneumatic Fire Detecting System, Details § 76.30-10 Location and spacing of tubing. (a) The tubing shall be located on the overhead or within 12 inches of the overhead on the bulkheads...

76 FR 44246 - Special Conditions: Boeing Model 747-8 Series Airplanes; Overhead Flight Attendant Rest Compartment

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-25

...; Special Conditions No. 25-442-SC] Special Conditions: Boeing Model 747-8 Series Airplanes; Overhead Flight... conditions. SUMMARY: These special conditions are issued for Boeing Model 747-8 series airplanes. These... applied for, and was granted, an extension of time for the amended type certificate, which changed the...

Cost Analysis and Overhead Charges at a Major Research University. AIR Forum 1982 Paper.

ERIC Educational Resources Information Center

Young, Michael E.; Geason, Ronald W.

The development of a cost allocation model at Ohio State University is discussed. The model was designed to measure the direct, indirect, and total operating costs of university operations and to recover general fund overhead costs associated with unrestricted general fund support of auxiliary enterprises and revenue-generating activities. The…

78 FR 53055 - Regulations Governing Fees for Services Performed in Connection With Licensing and Related...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-28

... the unchanged salary costs from the 2012 User Fee Update decision; no change in the publication cost levels of that decision; plus increase changes to two of the three Board overhead cost factors (the other overhead factor remains unchanged from its 2012 level), resulting from the mechanical application of the...

Overhead Projector Spectrum of Polymethine Dye: A Physical Chemistry Demonstration.

ERIC Educational Resources Information Center

Solomon, Sally; Hur, Chinhyu

1995-01-01

Encourages the incorporation into lecture of live experiments that can be predicted or interpreted with abstract models. A demonstration is described where the position of the predominant peak of 1,1'-diethyl-4,4'-cyanine iodide is measured in class using an overhead projector spectrometer, then predicted using the model of a particle in a…

40 CFR 52.1370 - Identification of plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Control Program, including all regulations found in Chapter VIII, Sub-Chapters 1-6, effective May 20, 1994... following phrase from section 3(B)(2) of exhibit A: “except that those sour water stripper overheads may be... during periods when the FCC CO boiler is unable to burn the sour water stripper overheads from the “old...

Growth, nitrogen use efficiency, and leachate comparison of subirrigated and overhead irrigated pale purple coneflower seedlings

Treesearch

Jeremy R. Pinto; Rhiannon A. Chandler; R. Kasten Dumroese

2008-01-01

Pale purple coneflower [Echinacea pallida (Nutt.) Nutt.] was grown within three container volumes (90, 105, and 340 cm3) under subirrigation and overhead irrigation treatments. Subirrigated coneflowers showed increased seedling quality with more biomass (14%), better nitrogen use efficiency (13%), greater nitrogen content (N; 11%), more height (15...

Early field performance of Acacia koa seedlings grown under subirrigation and overhead irrigation

Treesearch

Anthony S. Davis; Jeremiah R. Pinto; Douglass F. Jacobs

2011-01-01

Koa (Acacia koa A. Gray [Fabaceae]) seedlings were grown with subirrigation and overhead irrigation systems in an effort to characterize post-nursery field performance. One year following outplanting, we found no differences in seedling height or survival, but root-collar diameter was significantly larger for subirrigated seedlings. This indicates that koa seedlings,...

Marangoni Flowers and the Evil Eye: Overhead Presentations of Marangoni Flow

ERIC Educational Resources Information Center

Mundell, Donald W.

2009-01-01

Intermolecular forces and surface tension gradients in solutions lead to remarkable flows, known as Marangoni flows, where liquid flows from a region of low surface tension towards higher surface tension. Details of these flows, not visible to the naked eye, are made visible on an overhead projector owing to variation in the index of refraction.…

Nondestructive Testing of Overhead Transmission LINES—NUMERICAL and Experimental Investigation

NASA Astrophysics Data System (ADS)

Kulkarni, S.; Hurlebaus, S.

2009-03-01

Overhead transmission lines are periodically inspected using both on-ground and helicopter-aided visual inspection. Factors including sun glare, cloud cover, close proximity to power lines and the rapidly changing visual circumstances make airborne inspection of power lines a particularly hazardous task. In this study, a finite element model is developed that can be used to create the theoretical dispersion curves of an overhead transmission line. The numerical results are then verified with experimental test using a non-contact and broadband laser detection technique. The methodology developed in this study can be further extended to a continuous monitoring system and be applied to other cable monitoring applications, such as bridge cable monitoring, which would otherwise put human inspectors at risk.

Steps for arm and trunk actions of overhead forehand stroke used in badminton games across skill levels.

PubMed

Wang, Jianyu; Liu, Wenhao; Moffit, Jeffrey

2009-08-01

The purpose of this study was to examine arm and trunk actions in overhead forehand strokes used in badminton games across skill levels. The participants were 80 students (40 boys, 40 girls) who were randomly selected from video recordings of 300 students ages 16 to 19 years. The videotaped performances of overhead forehand strokes were coded based on three steps of arm action (elbow flexion, elbow and humeral flexion, and upward backswing) and three steps of trunk action (no trunk action, forward-backward movement, and trunk rotation). Students across the four skill levels exhibited different patterns of arm and trunk actions. Students at advanced levels used more mature arm and trunk actions.

Limiting electric fields of HVDC overhead power lines.

PubMed

Leitgeb, N

2014-05-01

As a consequence of the increased use of renewable energy and the now long distances between energy generation and consumption, in Europe, electric power transfer by high-voltage (HV) direct current (DC) overhead power lines gains increasing importance. Thousands of kilometers of them are going to be built within the next years. However, existing guidelines and regulations do not yet contain recommendations to limit static electric fields, which are one of the most important criteria for HVDC overhead power lines in terms of tower design, span width and ground clearance. Based on theoretical and experimental data, in this article, static electric fields associated with adverse health effects are analysed and various criteria are derived for limiting static electric field strengths.

Compression-based aggregation model for medical web services.

PubMed

Al-Shammary, Dhiah; Khalil, Ibrahim

2010-01-01

Many organizations such as hospitals have adopted Cloud Web services in applying their network services to avoid investing heavily computing infrastructure. SOAP (Simple Object Access Protocol) is the basic communication protocol of Cloud Web services that is XML based protocol. Generally,Web services often suffer congestions and bottlenecks as a result of the high network traffic that is caused by the large XML overhead size. At the same time, the massive load on Cloud Web services in terms of the large demand of client requests has resulted in the same problem. In this paper, two XML-aware aggregation techniques that are based on exploiting the compression concepts are proposed in order to aggregate the medical Web messages and achieve higher message size reduction.

Computing quality scores and uncertainty for approximate pattern matching in geospatial semantic graphs

DOE PAGES

Stracuzzi, David John; Brost, Randolph C.; Phillips, Cynthia A.; ...

2015-09-26

Geospatial semantic graphs provide a robust foundation for representing and analyzing remote sensor data. In particular, they support a variety of pattern search operations that capture the spatial and temporal relationships among the objects and events in the data. However, in the presence of large data corpora, even a carefully constructed search query may return a large number of unintended matches. This work considers the problem of calculating a quality score for each match to the query, given that the underlying data are uncertain. As a result, we present a preliminary evaluation of three methods for determining both match qualitymore » scores and associated uncertainty bounds, illustrated in the context of an example based on overhead imagery data.« less

Earth observations taken during STS-81 mission

NASA Image and Video Library

1997-01-22

STS081-750-048 (12-22 Jan. 1997) --- This photograph, made with a handheld 70mm camera aimed through the Space Shuttle Atlantis' overhead windows, shows the entire city-state of Singapore with its urban, industrial and commercial land use areas. Singapore is located at the tip of the Malay peninsula separated by Johor strait. This prosperous island state, once Asia's major trade center, is now highly industrialized despite its small area. The ideal location has made this island a hub of trade, shipping and service industries. This photograph shows the urban land uses and a large airport on the island. Several commercial harbors are seen on this photograph. The three large reservoirs in the center of the photograph are obscured by the clouds.

Parallel Visualization of Large-Scale Aerodynamics Calculations: A Case Study on the Cray T3E

NASA Technical Reports Server (NTRS)

Ma, Kwan-Liu; Crockett, Thomas W.

1999-01-01

This paper reports the performance of a parallel volume rendering algorithm for visualizing a large-scale, unstructured-grid dataset produced by a three-dimensional aerodynamics simulation. This dataset, containing over 18 million tetrahedra, allows us to extend our performance results to a problem which is more than 30 times larger than the one we examined previously. This high resolution dataset also allows us to see fine, three-dimensional features in the flow field. All our tests were performed on the Silicon Graphics Inc. (SGI)/Cray T3E operated by NASA's Goddard Space Flight Center. Using 511 processors, a rendering rate of almost 9 million tetrahedra/second was achieved with a parallel overhead of 26%.

Maximizing Information Diffusion in the Cyber-physical Integrated Network †

PubMed Central

Lu, Hongliang; Lv, Shaohe; Jiao, Xianlong; Wang, Xiaodong; Liu, Juan

2015-01-01

Nowadays, our living environment has been embedded with smart objects, such as smart sensors, smart watches and smart phones. They make cyberspace and physical space integrated by their abundant abilities of sensing, communication and computation, forming a cyber-physical integrated network. In order to maximize information diffusion in such a network, a group of objects are selected as the forwarding points. To optimize the selection, a minimum connected dominating set (CDS) strategy is adopted. However, existing approaches focus on minimizing the size of the CDS, neglecting an important factor: the weight of links. In this paper, we propose a distributed maximizing the probability of information diffusion (DMPID) algorithm in the cyber-physical integrated network. Unlike previous approaches that only consider the size of CDS selection, DMPID also considers the information spread probability that depends on the weight of links. To weaken the effects of excessively-weighted links, we also present an optimization strategy that can properly balance the two factors. The results of extensive simulation show that DMPID can nearly double the information diffusion probability, while keeping a reasonable size of selection with low overhead in different distributed networks. PMID:26569254

A Student Response System in an Electronic Classroom: Technology Aids for Large Classroom Instruction

NASA Astrophysics Data System (ADS)

Ober, D.; Errington, P.; Islam, S.; Robertson, T.; Watson, J.

1997-10-01

In the fall of 1996, thirteen (13) classrooms on the Ball State campus were equipped with technological aids to enhance learning in large classrooms (for typically 100 students or larger). Each classroom was equipped with the following built-in equipment: computer, zip drive, laser disc player, VCR, LAN and Internet connection, TV monitors, and Elmo overhead camera with large-screen projection system. This past fall semester a student response system was added to a 108-seat classroom in the Physics and Astronomy department for use with large General Education courses. Each student seat was equipped with a hardwired hand-held unit possessing input capabilities and LCD feedback for the student. The introduction of the student response system was added in order enhance more active learning by students in the large classroom environment. Attendance, quizzes, hour exams, and in-class surveys are early uses for the system; initial reactions by student and faculty users will be given.

10 Management Controller for Time and Space Partitioning Architectures

NASA Astrophysics Data System (ADS)

Lachaize, Jerome; Deredempt, Marie-Helene; Galizzi, Julien

2015-09-01

The Integrated Modular Avionics (IMA) has been industrialized in aeronautical domain to enable the independent qualification of different application softwares from different suppliers on the same generic computer, this latter computer being a single terminal in a deterministic network. This concept allowed to distribute efficiently and transparently the different applications across the network, sizing accurately the HW equipments to embed on the aircraft, through the configuration of the virtual computers and the virtual network. , This concept has been studied for space domain and requirements issued [D04],[D05]. Experiments in the space domain have been done, for the computer level, through ESA and CNES initiatives [D02] [D03]. One possible IMA implementation may use Time and Space Partitioning (TSP) technology. Studies on Time and Space Partitioning [D02] for controlling resources access such as CPU and memories and studies on hardware/software interface standardization [D01] showed that for space domain technologies where I/O components (or IP) do not cover advanced features such as buffering, descriptors or virtualization, CPU overhead in terms of performances is mainly due to shared interface management in the execution platform, and to the high frequency of I/O accesses, these latter leading to an important number of context switches. This paper will present a solution to reduce this execution overhead with an open, modular and configurable controller.

Coriolis-coupled wave packet dynamics of H + HLi reaction.

PubMed

Padmanaban, R; Mahapatra, S

2006-05-11

We investigated the effect of Coriolis coupling (CC) on the initial state-selected dynamics of H+HLi reaction by a time-dependent wave packet (WP) approach. Exact quantum scattering calculations were obtained by a WP propagation method based on the Chebyshev polynomial scheme and ab initio potential energy surface of the reacting system. Partial wave contributions up to the total angular momentum J=30 were found to be necessary for the scattering of HLi in its vibrational and rotational ground state up to a collision energy approximately 0.75 eV. For each J value, the projection quantum number K was varied from 0 to min (J, K(max)), with K(max)=8 until J=20 and K(max)=4 for further higher J values. This is because further higher values of K do not have much effect on the dynamics and also because one wishes to maintain the large computational overhead for each calculation within the affordable limit. The initial state-selected integral reaction cross sections and thermal rate constants were calculated by summing up the contributions from all partial waves. These were compared with our previous results on the title system, obtained within the centrifugal sudden and J-shifting approximations, to demonstrate the impact of CC on the dynamics of this system.

A real-space stochastic density matrix approach for density functional electronic structure.

PubMed

Beck, Thomas L

2015-12-21

The recent development of real-space grid methods has led to more efficient, accurate, and adaptable approaches for large-scale electrostatics and density functional electronic structure modeling. With the incorporation of multiscale techniques, linear-scaling real-space solvers are possible for density functional problems if localized orbitals are used to represent the Kohn-Sham energy functional. These methods still suffer from high computational and storage overheads, however, due to extensive matrix operations related to the underlying wave function grid representation. In this paper, an alternative stochastic method is outlined that aims to solve directly for the one-electron density matrix in real space. In order to illustrate aspects of the method, model calculations are performed for simple one-dimensional problems that display some features of the more general problem, such as spatial nodes in the density matrix. This orbital-free approach may prove helpful considering a future involving increasingly parallel computing architectures. Its primary advantage is the near-locality of the random walks, allowing for simultaneous updates of the density matrix in different regions of space partitioned across the processors. In addition, it allows for testing and enforcement of the particle number and idempotency constraints through stabilization of a Feynman-Kac functional integral as opposed to the extensive matrix operations in traditional approaches.

An integrated runtime and compile-time approach for parallelizing structured and block structured applications

NASA Technical Reports Server (NTRS)

Agrawal, Gagan; Sussman, Alan; Saltz, Joel

1993-01-01

Scientific and engineering applications often involve structured meshes. These meshes may be nested (for multigrid codes) and/or irregularly coupled (called multiblock or irregularly coupled regular mesh problems). A combined runtime and compile-time approach for parallelizing these applications on distributed memory parallel machines in an efficient and machine-independent fashion was described. A runtime library which can be used to port these applications on distributed memory machines was designed and implemented. The library is currently implemented on several different systems. To further ease the task of application programmers, methods were developed for integrating this runtime library with compilers for HPK-like parallel programming languages. How this runtime library was integrated with the Fortran 90D compiler being developed at Syracuse University is discussed. Experimental results to demonstrate the efficacy of our approach are presented. A multiblock Navier-Stokes solver template and a multigrid code were experimented with. Our experimental results show that our primitives have low runtime communication overheads. Further, the compiler parallelized codes perform within 20 percent of the code parallelized by manually inserting calls to the runtime library.

Trusted Operations on Sensor Data †

PubMed Central

Joosen, Wouter; Michiels, Sam; Hughes, Danny

2018-01-01

The widespread use of mobile devices has allowed the development of participatory sensing systems that capture various types of data using the existing or external sensors attached to mobile devices. Gathering data from such anonymous sources requires a mechanism to establish the integrity of sensor readings. In many cases, sensor data need to be preprocessed on the device itself before being uploaded to the target server while ensuring the chain of trust from capture to the delivery of the data. This can be achieved by a framework that provides a means to implement arbitrary operations to be performed on trusted sensor data, while guaranteeing the security and integrity of the data. This paper presents the design and implementation of a framework that allows the capture of trusted sensor data from both external and internal sensors on a mobile phone along with the development of trusted operations on sensor data while providing a mechanism for performing predefined operations on the data such that the chain of trust is maintained. The evaluation shows that the proposed system ensures the security and integrity of sensor data with minimal performance overhead. PMID:29702601

Advanced Concept

NASA Image and Video Library

2003-12-01

This photo gives an overhead look at an RS-88 development rocket engine being test fired at NASA's Marshall Space Flight Center in Huntsville, Alabama, in support of the Pad Abort Demonstration (PAD) test flights for NASA's Orbital Space Plane (OSP). The tests could be instrumental in developing the first crew launch escape system in almost 30 years. Paving the way for a series of integrated PAD test flights, the engine tests support development of a system that could pull a crew safely away from danger during liftoff. A series of 16 hot fire tests of a 50,000-pound thrust RS-88 rocket engine were conducted, resulting in a total of 55 seconds of successful engine operation. The engine is being developed by the Rocketdyne Propulsion and Power unit of the Boeing Company. Integrated launch abort demonstration tests in 2005 will use four RS-88 engines to separate a test vehicle from a test platform, simulating pulling a crewed vehicle away from an aborted launch. Four 156-foot parachutes will deploy and carry the vehicle to landing. Lockheed Martin is building the vehicles for the PAD tests. Seven integrated tests are plarned for 2005 and 2006.

A method of costing anaesthetic practice.

PubMed

Broadway, P J; Jones, J G

1995-01-01

This paper identifies the main factors involved in the cost of elective general anaesthetic practice. The costs of anaesthesia were divided into overheads and running costs, which are sensitive to the duration of anaesthesia, and fixed costs which are incurred by each patient but are not sensitive to the duration of anaesthesia. The overhead costs consisted of salaries, capital equipment and maintenance costs. The overhead cost of a consultant anaesthetist combined with a technical assistant's salary, monitoring equipment and anaesthetic machine was estimated at 45.05.h-1 pounds (using 1993 salary scales and prices). The fixed costs of pre-operative assessment and nursing care in recovery were the same for all patients, 20.60 pounds per patient. For the majority of anaesthetics the combined cost of the anaesthetist, overheads and postoperative care was about 70% of the total cost, the remainder being the running costs which included drugs, anaesthetic gases, vapours, intravenous fluids, sterile equipment and other disposable items. Four sample anaesthetics were costed in two ways: both methods used the same overhead and fixed cost per patient but one added the cost of all the individual drugs and consumables used, whereas the other grouped these together using a charge sheet which can be computerised and used prospectively to cost anaesthesia. There was close agreement between the costs derived with the two methods. The cost of a 30 min delay in the start of an operating session was 27.30 pounds (anaesthetist, assistant and nurse salary (9.50.h-1 pounds)) which is more than the cost of 2 h of propofol infusion anaesthesia.(ABSTRACT TRUNCATED AT 250 WORDS)

Pantograph-catenary monitoring by means of fibre Bragg grating sensors: Results from tests in an underground line

NASA Astrophysics Data System (ADS)

Bocciolone, Marco; Bucca, Giuseppe; Collina, Andrea; Comolli, Lorenzo

2013-12-01

One of the most common way to collect the traction current needed for the underground vehicle operation is by using the pantograph-overhead line system. The periodically check of pantographs and overhead lines is important to assure the correct interaction between the two systems in terms of good current collection quality. The main diagnostic tools are the monitoring of the vertical force between the overhead line and the pantograph head, and the vertical acceleration on the pantograph head. The pantograph system works under high voltage (1500 V, DC, in our tests) and high electromagnetic disturbances are present. For this reason, traditional electrical sensors can be used only with particular precautions that complicate the measurement set up; fibre optic sensors, and in particular fibre Bragg grating (FBG) sensors, are particularly suitable for this application. In this paper, the application of the FBG sensors on a pantograph for the monitoring of underground pantograph-catenary system is presented. FBG sensors are used to measure both the contact force and the vertical acceleration of the pantograph head. The same measurements are also gathered with a traditional electrical system, allowing a comparison. The result is a very good agreement between electrical and optical measurements, except in particular frequency ranges where the different positioning of the sensors influences the output, limiting the comparison. Moreover, some interesting results on the dynamic behaviour of the pantograph and its interaction with the overhead line are presented. Finally, a method to point out the main defects on the overhead line is shown.

Risk factors for, and prevention of, shoulder injuries in overhead sports: a systematic review with best-evidence synthesis.

PubMed

Asker, Martin; Brooke, Hannah L; Waldén, Markus; Tranaeus, Ulrika; Johansson, Fredrik; Skillgate, Eva; Holm, Lena W

2018-03-26

To assess the evidence for risk factors and prevention measures for shoulder injuries in overhead sports. Systematic review with best-evidence synthesis. Medline (Ovid), PubMed (complementary search), Embase (Elsevier), Cochrane (Wiley), SPORTDiscus (Ebsco) and Web of Science Core Collection (Thomson Reuters), from 1 January 1990 to 15 May 2017. Randomised controlled trials, cohort studies and case-control studies on risk factors or prevention measures for shoulder injuries in overhead sports. The eligible studies were quality assessed using the Scottish Intercollegiate Guidelines Network criteria. Of 4778 studies identified, 38 were eligible for quality review and 17 met the quality criteria to be included in the evidence synthesis. One additional quality study presented a shoulder injury prevention programme. Most studies focused on baseball, lacrosse or volleyball (n=13). The risk factors examined included participation level (competition vs training) (n=10), sex (n=4), biomechanics (n=2) and external workload (n=2). The evidence for all risk factors was limited or conflicting. The effect of the prevention programme within the subgroup of uninjured players at baseline was modest and possibly lacked statistical power. All investigated potential risk factors for shoulder injury in overhead sports had limited evidence, and most were non-modifiable (eg, sex). There is also limited evidence for the effect of shoulder injury prevention measures in overhead sports. CRD42015026850. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

How To Set Up Your Own Small Business. Volumes I-II and Overhead Transparencies.

ERIC Educational Resources Information Center

Fallek, Max

This two-volume textbook and collection of overhead transparency masters is intended for use in a course in setting up a small business. The following topics are covered in the first volume: getting off to a good start, doing market research, forecasting sales, financing a small business, understanding the different legal needs of different types…

26 CFR 1.482-7A - Methods to determine taxable income in connection with a cost sharing arrangement.

Code of Federal Regulations, 2010 CFR

2010-04-01

... reasonable overhead costs attributable to the project. They also share the cost of a conference facility that... reasonable overhead costs attributable to the project. USP also incurs costs related to field testing of the... Unrelated Third Party (UTP) enter into a cost sharing arrangement to develop new audio technology. In the...

26 CFR 1.482-7A - Methods to determine taxable income in connection with a cost sharing arrangement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... reasonable overhead costs attributable to the project. They also share the cost of a conference facility that... reasonable overhead costs attributable to the project. USP also incurs costs related to field testing of the... Unrelated Third Party (UTP) enter into a cost sharing arrangement to develop new audio technology. In the...

Visual quality testimony in an adversary setting

Treesearch

Bruce H. Murray; Bernard J. Niemann Jr.

1979-01-01

This paper documents the conditions, procedures, techniques and conclusions under which a utility was required to replace two-thirds of a mile segment of overhead 69 kv transmission line passing an Ice Age National Scieytific Reserve with underground at the cost of $950,000 vs. $60,000 for overhead (WPSC 1978). Because the proposed right-of-way would not, in this case...

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN. CONVEYOR PLATFORM,TRAM TRESTLE, AND LOADING PLATFORM. LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-47(CT) FOR IDENTICAL COLOR TRANSPARENCY. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OVERHEAD VIEW OF SECONDARY ORE BIN, CONVEYOR PLATFORM TRAM TRESTLE, AND LOADING PLATFORM, LOOKING SOUTHWEST. THE HOLE IN THE ORE BIN FLOOR CAN BE SEEN, AND BALL MILL FOUNDATION AT LOWER LEFT CORNER. SEE CA-291-13 FOR IDENTICAL B&W NEGATIVE. - Keane Wonder Mine, Park Route 4 (Daylight Pass Cutoff), Death Valley Junction, Inyo County, CA

The Overhead System: Production, Implementation and Utilization. 2nd Edition.

ERIC Educational Resources Information Center

Smith, Richard E.; Pearson, Jerry D.

This handbook is designed to help three groups: the administrator who does not have the services of a media specialist, the media specialist who wishes to expand his knowledge or skills, and the classroom teacher who recognizes the value of the overhead as a teaching tool and is looking for practical assistance. Guidelines are provided in 11…

26 CFR 1.482-7A - Methods to determine taxable income in connection with a cost sharing arrangement.

Code of Federal Regulations, 2012 CFR

2012-04-01

... reasonable overhead costs attributable to the project. They also share the cost of a conference facility that... reasonable overhead costs attributable to the project. USP also incurs costs related to field testing of the... Unrelated Third Party (UTP) enter into a cost sharing arrangement to develop new audio technology. In the...

26 CFR 1.482-7A - Methods to determine taxable income in connection with a cost sharing arrangement.

Code of Federal Regulations, 2013 CFR

2013-04-01

... reasonable overhead costs attributable to the project. They also share the cost of a conference facility that... reasonable overhead costs attributable to the project. USP also incurs costs related to field testing of the... Unrelated Third Party (UTP) enter into a cost sharing arrangement to develop new audio technology. In the...

26 CFR 1.482-7A - Methods to determine taxable income in connection with a cost sharing arrangement.

Code of Federal Regulations, 2014 CFR

2014-04-01

... reasonable overhead costs attributable to the project. They also share the cost of a conference facility that... reasonable overhead costs attributable to the project. USP also incurs costs related to field testing of the... Unrelated Third Party (UTP) enter into a cost sharing arrangement to develop new audio technology. In the...

20. VIEW TO WEST OF INTERIOR OF CRANEWAY WITH TOW ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. VIEW TO WEST OF INTERIOR OF CRANEWAY WITH TOW TRAVELING BRIDGE CRANES (ONE OVERHEAD IN FOREGROUND AND ONE OVERHEAD IN BACKGROUNDS). NOTE WOOD BLOCK PAVING ON THE FLOOR. FIRST FLOOR ASSEMBLY AREA IS THE SPACE IN THE BACKGROUND ON THE RIGHT. - Rosie the Riveter National Historical Park, Ford Assembly Plant, 1400 Harbour Way South, Richmond, Contra Costa County, CA

Life cycle assessment of overhead and underground primary power distribution.

PubMed

Bumby, Sarah; Druzhinina, Ekaterina; Feraldi, Rebe; Werthmann, Danae; Geyer, Roland; Sahl, Jack

2010-07-15

Electrical power can be distributed in overhead or underground systems, both of which generate a variety of environmental impacts at all stages of their life cycles. While there is considerable literature discussing the trade-offs between both systems in terms of aesthetics, safety, cost, and reliability, environmental assessments are relatively rare and limited to power cable production and end-of-life management. This paper assesses environmental impacts from overhead and underground medium voltage power distribution systems as they are currently built and managed by Southern California Edison (SCE). It uses process-based life cycle assessment (LCA) according to ISO 14044 (2006) and SCE-specific primary data to the extent possible. Potential environmental impacts have been calculated using a wide range of midpoint indicators, and robustness of the results has been investigated through sensitivity analysis of the most uncertain and potentially significant parameters. The studied underground system has higher environmental impacts in all indicators and for all parameter values, mostly due to its higher material intensity. For both systems and all indicators the majority of impact occurs during cable production. Promising strategies for impact reduction are thus cable failure rate reduction for overhead and cable lifetime extension for underground systems.

Towards a Low-Cost Remote Memory Attestation for the Smart Grid

PubMed Central

Yang, Xinyu; He, Xiaofei; Yu, Wei; Lin, Jie; Li, Rui; Yang, Qingyu; Song, Houbing

2015-01-01

In the smart grid, measurement devices may be compromised by adversaries, and their operations could be disrupted by attacks. A number of schemes to efficiently and accurately detect these compromised devices remotely have been proposed. Nonetheless, most of the existing schemes detecting compromised devices depend on the incremental response time in the attestation process, which are sensitive to data transmission delay and lead to high computation and network overhead. To address the issue, in this paper, we propose a low-cost remote memory attestation scheme (LRMA), which can efficiently and accurately detect compromised smart meters considering real-time network delay and achieve low computation and network overhead. In LRMA, the impact of real-time network delay on detecting compromised nodes can be eliminated via investigating the time differences reported from relay nodes. Furthermore, the attestation frequency in LRMA is dynamically adjusted with the compromised probability of each node, and then, the total number of attestations could be reduced while low computation and network overhead can be achieved. Through a combination of extensive theoretical analysis and evaluations, our data demonstrate that our proposed scheme can achieve better detection capacity and lower computation and network overhead in comparison to existing schemes. PMID:26307998

Towards a Low-Cost Remote Memory Attestation for the Smart Grid.

PubMed

Yang, Xinyu; He, Xiaofei; Yu, Wei; Lin, Jie; Li, Rui; Yang, Qingyu; Song, Houbing

2015-08-21

In the smart grid, measurement devices may be compromised by adversaries, and their operations could be disrupted by attacks. A number of schemes to efficiently and accurately detect these compromised devices remotely have been proposed. Nonetheless, most of the existing schemes detecting compromised devices depend on the incremental response time in the attestation process, which are sensitive to data transmission delay and lead to high computation and network overhead. To address the issue, in this paper, we propose a low-cost remote memory attestation scheme (LRMA), which can efficiently and accurately detect compromised smart meters considering real-time network delay and achieve low computation and network overhead. In LRMA, the impact of real-time network delay on detecting compromised nodes can be eliminated via investigating the time differences reported from relay nodes. Furthermore, the attestation frequency in LRMA is dynamically adjusted with the compromised probability of each node, and then, the total number of attestations could be reduced while low computation and network overhead can be achieved. Through a combination of extensive theoretical analysis and evaluations, our data demonstrate that our proposed scheme can achieve better detection capacity and lower computation and network overhead in comparison to existing schemes.

Sex Differences During an Overhead Squat Assessment.

PubMed

Mauntel, Timothy C; Post, Eric G; Padua, Darin A; Bell, David R

2015-08-01

A disparity exists between the rates of male and female lower extremity injuries. One factor that may contribute to this disparity is high-risk biomechanical patterns that are commonly displayed by females. It is unknown what biomechanical differences exist between males and females during an overhead squat. This study compared lower extremity biomechanics during an overhead squat and ranges of motion between males and females. An electromagnetic motion tracking system interfaced with a force platform was used to quantify peak lower extremity kinematics and kinetics during the descent phase of each squat. Range of motion measurements were assessed with a standard goniometer. Differences between male and female kinematics, kinetics, and ranges of motion were identified with t tests. Males displayed greater peak knee valgus angle, peak hip flexion angle, peak vertical ground reaction forces, and peak hip extension moments. Males also displayed less active ankle dorsiflexion with the knee extended and hip internal and external rotation than females. No other differences were observed. The biomechanical differences between males and females during the overhead squat may result from differences in lower extremity ranges of motion. Therefore, sex-specific injury prevention programs should be developed to improve biomechanics and ranges of motion.

The Kinetic Chain Revisited: New Concepts on Throwing Mechanics and Injury.

PubMed

Chu, Samuel K; Jayabalan, Prakash; Kibler, W Ben; Press, Joel

2016-03-01

The overhead throwing motion is a complex activity that is achieved through activation of the kinetic chain. The kinetic chain refers to the linkage of multiple segments of the body that allows for transfer of forces and motion. The lower extremities and core provide a base of support, generating energy that is transferred eventually through the throwing arm and hand, resulting in release of the ball. The kinetic chain requires optimal anatomy, physiology, and mechanics and is involved in all 6 phases of overhead throwing: windup, stride, arm cocking, acceleration, deceleration, and follow-through. Breaks or deficits in the kinetic chain can lead to injury or decreased performance. Through an understanding of the mechanics and pathomechanics seen in each phase of throwing, the clinician can better evaluate and screen for potential kinetic chain deficits in the overhead throwing athlete. The purpose of this article is to review the biomechanics of the overhead throwing motion, the role of the kinetic chain in throwing, and the clinical evaluation and management of abnormal throwing mechanics and related injuries. Copyright © 2016 American Academy of Physical Medicine and Rehabilitation. Published by Elsevier Inc. All rights reserved.

The Z1 truss is moved to check weight and balance

NASA Technical Reports Server (NTRS)

2000-01-01

In the Space Station Processing Facility, photographers focus on the Integrated Truss Structure Z1, an element of the International Space Station, suspended by a crane overhead. The truss is being moved to another stand to check its weight and balance. The Z1 truss is the first of 10 trusses that will become the backbone of the Space Station, eventually stretching the length of a football field. Along with its companion payload, the third Pressurized Mating Adapter, the Z1 is scheduled to be launched aboard Space Shuttle Discovery Oct. 5 at 9:38 p.m. EDT. The launch will be the 100th in the Shuttle program.

An information based approach to improving overhead imagery collection

NASA Astrophysics Data System (ADS)

Sourwine, Matthew J.; Hintz, Kenneth J.

2011-06-01

Recent growth in commercial imaging satellite development has resulted in a complex and diverse set of systems. To simplify this environment for both customer and vendor, an information based sensor management model was built to integrate tasking and scheduling systems. By establishing a relationship between image quality and information, tasking by NIIRS can be utilized to measure the customer's required information content. Focused on a reduction in uncertainty about a target of interest, the sensor manager finds the best sensors to complete the task given the active suite of imaging sensors' functions. This is done through determination of which satellite will meet customer information and timeliness requirements with low likelihood of interference at the highest rate of return.

STS-110 payload S0 Truss is moved to payload canister in O&C

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- In the Operations and Checkout Building, an overhead crane carries the Integrated Truss Structure S0 from its workstand toward the payload canister. The S0 truss will be transported to the launch pad for mission STS-110. Part of the payload, the S0 truss will become the backbone of the orbiting International Space Station (ISS), at the center of the 10-truss, girderlike structure that will ultimately extend the length of a football field on the ISS. The S0 truss will be attached to the U.S. Lab, 'Destiny,' on the 11-day mission. Launch is scheduled for April 4.

Do overhead sports increase risk for rotator cuff tears in wheelchair users?

PubMed

Akbar, Michael; Brunner, Manuela; Ewerbeck, Volker; Wiedenhöfer, Bernd; Grieser, Thomas; Bruckner, Thomas; Loew, Markus; Raiss, Patric

2015-03-01

To analyze whether frequent overhead-sports activity increases the risk for rotator cuff disease in patients with spinal cord injuries (SCIs) who are wheelchair dependent. Cross-sectional study, risk analysis. Department of Orthopaedic Surgery, Trauma Surgery and Spinal Cord Injury. Patients (N=296) with SCI requiring the full-time use of a manual wheelchair were recruited for this study. The total population was divided into 2 groups (sports vs no sports), among them 103 patients playing overhead sports on a regular basis (at least 1-2 times/wk) and 193 patients involved in overhead sports less than once a week or in no sports activity at all. The mean age of the sports group was 49.1 years. The mean duration of wheelchair dependence was 26.5 years. The mean age of the no-sports group was 48 years. The mean duration of wheelchair dependence was 25.2 years. Each individual completed a questionnaire designed to identify overhead-sports activity on a regular basis and was asked about shoulder problems. Magnetic resonance imaging scans of both shoulders were performed in each patient and analyzed in a standardized fashion. None. Possible differences in continuous data between patients with and without rotator cuff tear were evaluated. The relative risk of suffering from a rotator cuff tear between patients playing overhead sports and those not playing overhead sports was calculated. One hundred three patients played overhead sports regularly and 193 did not. There was no difference between groups regarding age, sex, level of SCI, and duration of wheelchair dependence. The body mass index was significantly lower in the sports group than in the no-sports group (P<.0001). A rotator cuff tear was present in 75.7% of the patients in the sports group and in 36.3% of the patients in the no-sports group (P<.0001). Rotator cuff tears were symptomatic in 92.6% of the patients. The estimated risk increase for the sports group to develop rotator cuff tears was twice as high as for the no-sports group (95% confidence interval, 1.7-2.6; P<.001). Similar results were found for the neurological level of lesion (T2-7/

Self-actuating grapple automatically engages and releases loads from overhead cranes

NASA Technical Reports Server (NTRS)

Froehlich, J. A.; Karastas, G. A.

1966-01-01

Two-piece grapple mechanism consisting of a lift knob secured to the load and a grapple member connected to the crane or lift automatically disengages the load from the overhead lifting device when the load contacts the ground. The key feature is the sliding collar under the lift knob which enables the grapple latch to be stripped off over the lift knob.

Subirrigation reduces water use, nitrogen loss, and moss growth in a container nursery

Treesearch

R. Kasten Dumroese; Jeremy R. Pinto; Douglass F. Jacobs; Anthony S. Davis; Baron Horiuchi

2006-01-01

With about half the amount of water, subirrigated Metrosideros polymorpha Gaud. (Myrtaceae) grown 9 mo in a greenhouse were similar to those irrigated with an existing fixed overhead irrigation system; moss growth was about 3X greater in the fixed overhead system after 3 mo. Moss growth was affected by the rate of preplant controlled release fertilizer added (more...

Demonstrating Biological Principles Efficiently and Effectively: The Overhead Is More than Just a Lighted Chalkboard

ERIC Educational Resources Information Center

Barden-Gabbei, Laura M.

2006-01-01

The overhead projector is an excellent tool for teachers at both the high school and college level. Teachers often use it to display class notes as they monitor students' actions and reactions to the concepts being presented and discussed, to display diagrams and figures too complex to draw on the chalkboard, and more recently to display computer…

Communication overhead on the Intel iPSC-860 hypercube

NASA Technical Reports Server (NTRS)

Bokhari, Shahid H.

1990-01-01

Experiments were conducted on the Intel iPSC-860 hypercube in order to evaluate the overhead of interprocessor communication. It is demonstrated that: (1) contrary to popular belief, the distance between two communicating processors has a significant impact on communication time, (2) edge contention can increase communication time by a factor of more than 7, and (3) node contention has no measurable impact.

IMPROVING PROCEDURES FOR PRODUCING OVERHEAD TRANSPARENCIES WITH THE ULTIMATE AIM OF INCORPORATING THESE TECHNIQUES INTO THE DEVELOPMENT OF A REGIONAL CURRICULAR MATERIALS CENTER FOR VOCATIONAL EDUCATION. FINAL REPORT.

ERIC Educational Resources Information Center

JENSEN, ARTHUR K.

THE INVESTIGATION RESULTED IN THE PRODUCTION OF 88 LOW-COST OVERHEAD PROJECTION TRANSPARENCIES ON THE BASIC PRINCIPLES OF POWER TRANSMISSION IN AGRICULTURAL MACHINERY. DEVELOPING TECHNIQUES FOR OFFSET PRINTING ON PLASTIC REQUIRED OVERCOMING PROBLEMS OF STATIC ELECTRICITY, INK ADHESION, OFFSETTING, AND DRYING. MACHINERY, ENVIRONMENT, AND INK WERE…

Software Voting in Asynchronous NMR (N-Modular Redundancy) Computer Structures.

DTIC Science & Technology

1983-05-06

added reliability is exchanged for increased system cost and decreased throughput. Some applications require extremely reliable systems, so the only...not the other way around. Although no systems proidc abstract voting yet. as more applications are written for NMR systems, the programmers are going...throughput goes down, the overhead goes up. Mathematically : Overhead= Non redundant Throughput- Actual Throughput (1) In this section, the actual throughput

A STATE DEMONSTRATION AND EVALUATION IN DEVELOPING PILOT OVERHEAD TRANSPARENCIES FOR THE SUBJECT AREAS OF SECONDARY SCIENCE, MATHEMATICS, ENGLISH, MODERN FOREIGN LANGUAGES, AND GEOGRAPHY.

ERIC Educational Resources Information Center

KINNIELL, WILLIAM T.; AND OTHERS

A DEMONSTRATION PROGRAM WAS UNDERTAKEN FOR THE PURPOSE OF SHOWING HOW A STATE DEPARTMENT OF EDUCATION CAN UTILIZE ITS RESOURCES AND SUBJECT MATTER SPECIALISTS IN DEVELOPING OVERHEAD TRANSPARENCIES TO IMPLEMENT SECONDARY SCHOOL CURRICULUM IN THE STATE. SUBJECT SPECIALISTS (26) REPRESENTING 10 COURSE FIELDS WERE BROUGHT TOGETHER AT THE BEGINNING OF…

Acromiohumeral Distance and 3-Dimensional Scapular Position Change After Overhead Muscle Fatigue

PubMed Central

Maenhout, Annelies; Dhooge, Famke; Van Herzeele, Maarten; Palmans, Tanneke; Cools, Ann

2015-01-01

Context: Muscle fatigue due to repetitive and prolonged overhead sports activity is considered an important factor contributing to impingement-related rotator cuff pathologic conditions in overhead athletes. The evidence on scapular and glenohumeral kinematic changes after fatigue is contradicting and prohibits conclusions about how shoulder muscle fatigue affects acromiohumeral distance. Objective: To investigate the effect of a fatigue protocol resembling overhead sports activity on acromiohumeral distance and 3-dimensional scapular position in overhead athletes. Design: Cross-sectional study. Setting: Institutional laboratory. Patients or Other Participants: A total of 29 healthy recreational overhead athletes (14 men, 15 women; age = 22.23 ± 2.82 years, height = 178.3 ± 7.8 cm, mass = 71.6 ± 9.5 kg). Intervention(s) The athletes were tested before and after a shoulder muscle-fatiguing protocol. Main Outcome Measure(s) Acromiohumeral distance was measured using ultrasound, and scapular position was determined with an electromagnetic motion-tracking system. Both measurements were performed at 3 elevation positions (0°, 45°, and 60° of abduction). We used a 3-factor mixed model for data analysis. Results: After fatigue, the acromiohumeral distance increased when the upper extremity was actively positioned at 45° (Δ = 0.78 ± 0.24 mm, P = .002) or 60° (Δ = 0.58 ± 0.23 mm, P = .02) of abduction. Scapular position changed after fatigue to a more externally rotated position at 45° (Δ = 4.97° ± 1.13°, P < .001) and 60° (Δ = 4.61° ± 1.90°, P = .001) of abduction, a more upwardly rotated position at 45° (Δ = 6.10° ± 1.30°, P < .001) and 60° (Δ = 7.20° ± 1.65°, P < .001) of abduction, and a more posteriorly tilted position at 0°, 45°, and 60° of abduction (Δ = 1.98° ± 0.41°, P < .001). Conclusions: After a fatiguing protocol, we found changes in acromiohumeral distance and scapular position that corresponded with an impingement-sparing situation. PMID:25594913

Fast evaluation of scaled opposite spin second-order Møller-Plesset correlation energies using auxiliary basis expansions and exploiting sparsity.

PubMed

Jung, Yousung; Shao, Yihan; Head-Gordon, Martin

2007-09-01

The scaled opposite spin Møller-Plesset method (SOS-MP2) is an economical way of obtaining correlation energies that are computationally cheaper, and yet, in a statistical sense, of higher quality than standard MP2 theory, by introducing one empirical parameter. But SOS-MP2 still has a fourth-order scaling step that makes the method inapplicable to very large molecular systems. We reduce the scaling of SOS-MP2 by exploiting the sparsity of expansion coefficients and local integral matrices, by performing local auxiliary basis expansions for the occupied-virtual product distributions. To exploit sparsity of 3-index local quantities, we use a blocking scheme in which entire zero-rows and columns, for a given third global index, are deleted by comparison against a numerical threshold. This approach minimizes sparse matrix book-keeping overhead, and also provides sufficiently large submatrices after blocking, to allow efficient matrix-matrix multiplies. The resulting algorithm is formally cubic scaling, and requires only moderate computational resources (quadratic memory and disk space) and, in favorable cases, is shown to yield effective quadratic scaling behavior in the size regime we can apply it to. Errors associated with local fitting using the attenuated Coulomb metric and numerical thresholds in the blocking procedure are found to be insignificant in terms of the predicted relative energies. A diverse set of test calculations shows that the size of system where significant computational savings can be achieved depends strongly on the dimensionality of the system, and the extent of localizability of the molecular orbitals. Copyright 2007 Wiley Periodicals, Inc.

Construct validity of functional capacity tests in healthy workers

PubMed Central

2013-01-01

Background Functional Capacity (FC) is a multidimensional construct within the activity domain of the International Classification of Functioning, Disability and Health framework (ICF). Functional capacity evaluations (FCEs) are assessments of work-related FC. The extent to which these work-related FC tests are associated to bio-, psycho-, or social factors is unknown. The aims of this study were to test relationships between FC tests and other ICF factors in a sample of healthy workers, and to determine the amount of statistical variance in FC tests that can be explained by these factors. Methods A cross sectional study. The sample was comprised of 403 healthy workers who completed material handling FC tests (lifting low, overhead lifting, and carrying) and static work FC tests (overhead working and standing forward bend). The explainable variables were; six muscle strength tests; aerobic capacity test; and questionnaires regarding personal factors (age, gender, body height, body weight, and education), psychological factors (mental health, vitality, and general health perceptions), and social factors (perception of work, physical workloads, sport-, leisure time-, and work-index). A priori construct validity hypotheses were formulated and analyzed by means of correlation coefficients and regression analyses. Results Moderate correlations were detected between material handling FC tests and muscle strength, gender, body weight, and body height. As for static work FC tests; overhead working correlated fair with aerobic capacity and handgrip strength, and low with the sport-index and perception of work. For standing forward bend FC test, all hypotheses were rejected. The regression model revealed that 61% to 62% of material handling FC tests were explained by physical factors. Five to 15% of static work FC tests were explained by physical and social factors. Conclusions The current study revealed that, in a sample of healthy workers, material handling FC tests were related to physical factors but not to the psychosocial factors measured in this study. The construct of static work FC tests remained largely unexplained. PMID:23758870

Exercise prescription for overhead athletes with shoulder pathology: a systematic review with best evidence synthesis.

PubMed

Wright, Alexis A; Hegedus, Eric J; Tarara, Daniel T; Ray, Samantha C; Dischiavi, Steven L

2018-02-01

To produce a best evidence synthesis of exercise prescription used when treating shoulder pathology in the overhead athlete. A systematic review of exercises used in overhead athletes including case studies and clinical commentaries. MEDLINE, PubMed, SPORTDiscus and CINAHL from database inception through July 8, 2016. We examined data from randomised controlled trials and prospective cohort (level I-IV evidence) studies that addressed exercise intervention in the rehabilitation of the overhead athlete with shoulder pathology. Case studies and clinical commentaries (level V evidence) were examined to account for expert opinion-based research. Data were combined using best evidence synthesis and graded (A-F) recommendations (Centre for Evidence-Based Medicine). There were 33 unique exercises in six level I-IV studies that met our inclusion criteria. Most exercises were single-plane, upper extremity exercises performed below 90 o of elevation. There were 102 unique exercises in 33 level V studies that met our inclusion criteria. These exercises emphasised plyometrics, kinetic chain and sport-specific training. Overall, evidence for exercise interventions in overhead athletes with shoulder pathology is dominated by expert opinion (grade D). There is great variability between exercise approaches suggested by experts and those investigated in research studies and the overall level of evidence is low. The strongest available evidence (level B) supports the use of single-plane, open chain upper extremity exercises performed below 90° of elevation and closed chain upper extremity exercises. Clinical expert pieces support a more advanced, global treatment approach consistent with the complex, multidimensional nature of sport. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.