Investigation of the Deposition and Densification Parameters on the Mechanical Properties of Pressurized Spray Deposited (PSD) 3-D Printed Ceramic Components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menchhofer, Paul A.; Becker, Benjamin

Oak Ridge National Laboratory (ORNL) and HotEnd Works teamed to investigate the use of pressurized spray deposition (PSD) technology for the production of ceramic parts via additive manufacturing. Scanning electron microscopy of sintered parts provided by HotEnd Works revealed voids large enough to compromise the mechanical properties of PSD manufactured parts. Scanning electron microscopy and particle size analysis of the alumina oxide powder feedstocks indicated that the powders contained some large particles and some agglomerations in the powder. Further classification of the powder feedstocks and removal of the agglomerates by sonication in the liquid used for the PSD process aremore » recommended. Analysis of sintered parts indicated that the sonic modulus for the alumina part is consistent with other known values for alumina. The density for this part was determined by standard Archimedes immersion density methods and was found to be > 99.7 % of the theoretical density for pure alumina.« less

Determining potential wildlife benefits from wildfire in Arizona ponderosa pine forests

Treesearch

Philip O. Lowe; Peter F. Ffolliott; John H. Dieterich; David R. Patton

1978-01-01

Large wildfires are frequently destructive to the timber resource, but wildlife may not be so adversely affected. A study of selected species of wildlife (deer, elk, rodents, and birds) that were present on large burned areas, 1, 3, 7, and 20 years old, indicated population fluctuations and habitat changes that are, for the most part, predictable, and can be expressed...

Small and large particle limits of single scattering albedo for homogeneous, spherical particles

NASA Astrophysics Data System (ADS)

Moosmüller, H.; Sorensen, C. M.

2018-01-01

The aerosol single scattering albedo (SSA) is the dominant intensive particle parameter determining aerosols direct radiative forcing. For homogeneous spherical particles and a complex refractive index independent of wavelength, the SSA is solely dependent on size parameter (ratio of particle circumference and wavelength) and complex refractive index of the particle. Here, we explore this dependency for the small and large particle limits with size parameters much smaller and much larger than one. We show that in the small particle limit of Rayleigh scattering, a novel, generalized size parameter can be introduced that unifies the SSA dependence on particle size parameter independent of complex refractive index. In the large particle limit, SSA decreases with increasing product of imaginary part of the refractive index and size parameter, another generalized parameter, until this product becomes about one, then stays fairly constant until the imaginary part of the refractive index becomes comparable with the real part minus one. Beyond this point, particles start to acquire metallic character and SSA quickly increases with the imaginary part of the refractive index and approaches one.

The health of Canada’s children. Part III: Public policy and the social determinants of children’s health

PubMed Central

Raphael, Dennis

2010-01-01

The health of Canada’s children does not compare well with other wealthy industrialized nations. Significant inequalities in health exist among Canadian children, and many of these inequalities are due to variations in Canadian children’s life circumstances – the social determinants of health. The present article describes the social determinants of children’s health and explains how the quality of these social determinants is shaped, in large part, by public policy decisions. The specific public policies that shape the quality of Canadian children’s health are examined, and Canadian approaches in comparison with other wealthy developed nations are described. Policy directions that would improve the quality of the social determinants of children’s health are presented and barriers to their implementation are considered. PMID:21358893

[Determinants of the choice of part time employment and nurses' satisfaction: a multicentre descriptive study].

PubMed

Ferrazzo, Martino; Filippi, Mauro; Meneghetti, Giulia; Palese, Alvisa

2012-01-01

To describe the main determinants for the choice of part time employment in Italian nurses and its' impact on work satisfaction. The main factors were identified with a focus-group. A questionnaire with 26 items for the choice of part time and 24 for work satisfaction was then devised and administered to part time nurses (503) of 5 North Italian hospitals. Two-hundred fifty-five nurses/471 answered the questionnaire. The choice of part time was voluntary for the large majority of nurses (251, 98.4%) except for 4 (1.6%) that asked for it for health problems (personal or of the spouse). Part time nurses are more satisfied for the relationships with colleagues (average 3; SD 0.6), the opportunity to deal with responsibilities (2.9; SD 0.6) and to have free time (2.9; SD 0.6). CONCLUSIONS; Part time is a need for mothers. Part time nurses complain for lack of access to information on patients and lack of involvement in ward projects and planned changes, possibly to be considered signals of isolation.

The Cosmic Century

NASA Astrophysics Data System (ADS)

Longair, Malcolm S.

2013-04-01

Part I. Stars and Stellar Evolution up to the Second World War: 1. The legacy of the nineteenth century; 2. The classification of stellar spectra; 3. Stellar structure and evolution; 4. The end points of stellar evolution; Part II. The Large-Scale Structure of the Universe, 1900-1939: 5. The Galaxy and the nature of spiral nebulae; 6. The origins of astrophysical cosmology; Part III. The Opening up of the Electromagnetic Spectrum: 7. The opening up of the electromagnetic spectrum and the new astronomies; Part IV. The Astrophysics of Stars and Galaxies since 1945: 8. Stars and stellar evolution; 9. The physics of the interstellar medium; 10. The physics of galaxies and clusters of galaxies; 11. High-energy astrophysics; Part V. Astrophysical Cosmology since 1945: 12. Astrophysical cosmology; 13. The determination of cosmological parameters; 14. The evolution of galaxies and active galaxies with cosmic epoch; 15. The origin of galaxies and the large-scale structure of the Universe; 16. The very early Universe; References; Name index; Object index; Subject index.

Part D implementation: how did health plans fare? A conversation with Stan Nowak, founder, president, and chief executive officer of Silverlink Communications. Interview by William Atkinson.

PubMed

Nowak, Stan

2006-01-01

Medicare part D is a large-scale example of a true consumer-directed health insurance plan. With Part D, 42 million Americans can select from any one of dozens of Medicare Advantage or stand-alone prescription plans available to them. At the end of each year, beneficiaries will be able to evaluate their satisfaction with their chosen plan, assess other available options and determine whether to re-enroll or choose a new plan. Consumers rule.

Asynchrony, Fragmentation, and Scale Determine Benefits of Landscape Heterogeneity to Mobile Herbivores

USDA-ARS?s Scientific Manuscript database

Fragmentation of landscapes into spatially isolated parts is a prevailing source of environmental change worldwide. However, predicting the consequences of fragmentation for populations remains problematic, in large measure because the mechanisms translating landscape change into population performa...

The theory of nonstationary thermophoresis of a solid spherical particle

NASA Astrophysics Data System (ADS)

Kuzmin, M. K.; Yalamov, Yu. I.

2007-06-01

The theory of nonstationary thermophoresis of a solid spherical particle in a viscous gaseous medium is presented. The theory is constructed on the solutions of fluid-dynamics and thermal problems, each of which is split into stationary and strictly nonstationary parts. The solution of the stationary parts of the problems gives the final formula for determining the stationary component of the thermophoretic velocity of this particle. To determine the nonstationary component of the thermophoretic velocity of the particle, the corresponding formula in the space of Laplace transforms is derived. The limiting value theorems from operational calculus are used for obtaining the dependence of the nonstationary component of the thermophoretic velocity of the spherical particle on the strictly nonstationary temperature gradient for large and small values of time. The factors determining the thermophoretic velocity of the particle under investigation are determined.

Children Who Desperately Want To Read, but Are Not Working at Grade Level: Use Movement Patterns as "Windows" To Discover Why. Part III: The Frontal Midline.

ERIC Educational Resources Information Center

Corso, Marjorie

A longitudinal research study observed 30 children between the ages of infancy and elementary age to determine if using large muscle motor patterns to master the three identified midlines that concur with the body planes used in anatomy is reflected in academic classroom learning levels. This third part of the study focused on the frontal midline.…

Epidemiology of Cardiovascular Diseases.

ERIC Educational Resources Information Center

Jenkins, C. David

1988-01-01

Reviews epidemiological studies of cardiovascular diseases especially coronary heart disease (CHD), to document their major public health importance, changes in mortality during this century, and international comparisons of trends. Finds major risk factors for CHD are determined in large part by psychosocial and behavioral mechanisms. Asserts…

Stellarator Saddle Coils

NASA Astrophysics Data System (ADS)

Boozer, Allen H.

1999-11-01

Modern stellarators are designed using J. Nuehrenberg’s method of varying Fourier coefficients in the shape of the plasma boundary to maximize a target function. The matrix of second derivatives of the target function at the optimum determines a quality matrix. This matrix gives the degradation in the quality of the configuration as the normal magnetic field is varied on a control surface, which lies on or outside the plasma surface. The task is finding saddle coils that produce the desired configuration in the presence of a given toroidal field. An eigenvector of the quality matrix can be important for two reasons: (1) the normal field that must be produced by the saddles is large or (2) the eigenvalue is large (an island-causing resonant perturbation). The rank of the important part of the quality matrix is the number of important eigenvectors. The current in each saddle coil produces a normal field on the control surface, which can be described by an inductance matrix. The relevant part of the inductance matrix has large eigenvalues. The coils can produce the configuration if the rank of the important part of the quality matrix and its product with the relevant part of the inductance matrix are the same. Existing coil design codes, pioneered by P. Merkel, approximate the quality matrix by the unit matrix. Stellarator flexibility could be enhanced by using a more realistic quality matrix and by using trim coils to balance large eigenvalues.

A preliminary theoretical study of double blade two-dimensional aerodynamics for applications to vertical axis wind turbines

NASA Astrophysics Data System (ADS)

Weibust, E.

1981-04-01

A NASA model for computing the subsonic, viscous, attached flow around multielement airfoils was used to determine the amount of energy lost when using double blades rather than single ones. The resulting tangential force for the double or single blade configuration used as a criterion is found. Radial spacing, toe-in toe-out angle and tangential displacement (stagger) were varied to see how tagential force is affected. The greatest tangential force values are found to be achieved for maximum allowable radial spacing, which is determined by structural considerations, and is assumed to be on the order of 1.5 c. At this rather large distance, stagger as well as toe-in toe-out angle only gives slight improvements as long as the flow separation effects (stall region) are not considered. A large part of the energy is captured at relatively high wind speeds when the flow on the blades is partly separated (stalled).

Relative Velocity as a Metric for Probability of Collision Calculations

NASA Technical Reports Server (NTRS)

Frigm, Ryan Clayton; Rohrbaugh, Dave

2008-01-01

Collision risk assessment metrics, such as the probability of collision calculation, are based largely on assumptions about the interaction of two objects during their close approach. Specifically, the approach to probabilistic risk assessment can be performed more easily if the relative trajectories of the two close approach objects are assumed to be linear during the encounter. It is shown in this analysis that one factor in determining linearity is the relative velocity of the two encountering bodies, in that the assumption of linearity breaks down at low relative approach velocities. The first part of this analysis is the determination of the relative velocity threshold below which the assumption of linearity becomes invalid. The second part is a statistical study of conjunction interactions between representative asset spacecraft and the associated debris field environment to determine the likelihood of encountering a low relative velocity close approach. This analysis is performed for both the LEO and GEO orbit regimes. Both parts comment on the resulting effects to collision risk assessment operations.

Determination of initial conditions for heat exchanger placed in furnace by burning pellets

NASA Astrophysics Data System (ADS)

Durčanský, Peter; Jandačka, Jozef; Kapjor, Andrej

2014-08-01

Objective of the experimental facility and subsequent measurements is generally determine whether the expected physical properties of the verification, identification of the real behavior of the proposed system, or part thereof. For the design of heat exchanger for combined energy machine is required to identify and verify a large number of parameters. One of these are the boundary conditions of heat exchanger and pellets burner.

Flocking particles in a non-Newtonian shear thickening fluid

NASA Astrophysics Data System (ADS)

Mucha, Piotr B.; Peszek, Jan; Pokorný, Milan

2018-06-01

We prove the existence of strong solutions to the Cucker–Smale flocking model coupled with an incompressible viscous non-Newtonian fluid with the stress tensor of a power–law structure for . The fluid part of the system admits strong solutions while the solutions to the CS part are weak. The coupling is performed through a drag force on a periodic spatial domain . Additionally, we construct a Lyapunov functional determining the large time behavior of solutions to the system.

Extreme Universe Space Observatory (EUSO) Optics Module

NASA Technical Reports Server (NTRS)

Young, Roy; Christl, Mark

2008-01-01

A demonstration part will be manufactured in Japan on one of the large Toshiba machines with a diameter of 2.5 meters. This will be a flat PMMA disk that is cut between 0.5 and 1.25 meters radius. The cut should demonstrate manufacturing the most difficult parts of the 2.5 meter Fresnel pattern and the blazed grating on the diffractive surface. Optical simulations, validated with the subscale prototype, will be used to determine the limits on manufacturing errors (tolerances) that will result in optics that meet EUSO s requirements. There will be limits on surface roughness (or errors at high spatial frequency); radial and azimuthal slope errors (at lower spatial frequencies) and plunge cut depth errors in the blazed grating. The demonstration part will be measured to determine whether it was made within the allowable tolerances.

Outcomes of three part-time faculty development fellowship programs.

PubMed

Anderson, W A; Stritter, F T; Mygdal, W K; Arndt, J E; Reid, A

1997-03-01

Part-time faculty development fellowship programs have trained large numbers of new physician faculty for family medicine education programs. This study reviews data from three part-time fellowship programs to determine how well the programs train new faculty and the academic success of fellowship graduates. Part-time fellowship programs at Michigan State University, the University of North Carolina, and the Faculty Development Center in Waco, Tex, sent written surveys to graduates as part of routine follow-up studies. Graduates were asked to report their current status in academic medicine, how they spend their time, measures of academic productivity, and assessments of how well their training prepared them for their current academic positions. Data were complied at each institution and sent to Michigan State University for analysis. The majority of graduates (76%) have remained in their academic positions, and half (49%) teach in medically underserved settings. Graduates report high levels of satisfaction with the training they received. Thirty-two percent of graduates have published peer-reviewed articles, and almost 50% have presented at peer-reviewed meetings. Part-time fellowship programs have been successful at training and retaining large numbers of new faculty for family medicine.

The Wealth of Mexican Americans

ERIC Educational Resources Information Center

Cobb-Clark, Deborah A.; Hildebrand, Vincent A.

2006-01-01

This paper analyzes the sources of disparities in the relative wealth position of Mexican Americans. Results reveal that--unlike the racial wealth gap--Mexican Americans' wealth disadvantage is in large part not the result of differences in wealth distributions conditional on the underlying determinants of wealth. Rather, Mexican Americans' wealth…

Buried topography of Utopia, Mars - Persistence of a giant impact depression

NASA Technical Reports Server (NTRS)

Mcgill, George E.

1989-01-01

Knobs, partially buried craters, ring fractures, and some mesas permit a qualitative determination of the topography buried beneath younger northern plains materials. These features are widely distributed in the Utopia area but are absent in a large, roughly circular region centered at about 48 deg N, 240 deg W. This implies the existence of a circular depression about 3300 km in diameter buried beneath Utopia Planitia that is interpreted to represent the central part of a very large impact basin. The presence of buried curved massifs around part of this depression, and a roughly coincident mascon, lend further support. Present topography, areal geology, and paleotopography of buried surfaces all point to the persistence of this major depression for almost the entire history of Mars.

Collaborating to Improve Instruction: It's about Time

ERIC Educational Resources Information Center

Zimmerman, Judith A.; Grier, Harriett L.

2005-01-01

The success of implementing school change is determined in large part by the effectiveness of building leadership and time utilization. This paper describes the changing role of an urban principal as her building moved from a traditional junior high structure to a more collaborative small-school structure involving interdisciplinary grade-level…

Instructional Supervision in Public Secondary Schools in Kenya

ERIC Educational Resources Information Center

Wanzare, Zachariah

2012-01-01

This article reports some findings of study regarding practices and procedures of internal instructional supervision in public secondary schools in Kenya. The findings are part of a large-scale project undertaken in Kenya to determine the perceptions of headteachers, teachers and senior government education officers regarding the practices of…

Time to Terminate Toilet Papering

ERIC Educational Resources Information Center

Moscinski, David

2008-01-01

Each September in Wisconsin students return to school, football games draw enthusiastic crowds, and homecoming week is celebrated. Trees lose their leaves only to be re-adorned in white in that generation bridging tradition known as toilet papering. Community residents have differing opinions on "tp"ing, in large part determined by whether they…

Development of near-infrared spectroscopy calibrations to measure quality characteristics in intact Brassicaceae germplasm

USDA-ARS?s Scientific Manuscript database

Determining seed quality parameters is an integral part of cultivar improvement and germplasm screening. However, quality tests are often time cnsuming, seed destructive, and can require large seed samples. This study describes the development of near-infrared spectroscopy (NIRS) calibrations to mea...

Large-scale weakly supervised object localization via latent category learning.

PubMed

Chong Wang; Kaiqi Huang; Weiqiang Ren; Junge Zhang; Maybank, Steve

2015-04-01

Localizing objects in cluttered backgrounds is challenging under large-scale weakly supervised conditions. Due to the cluttered image condition, objects usually have large ambiguity with backgrounds. Besides, there is also a lack of effective algorithm for large-scale weakly supervised localization in cluttered backgrounds. However, backgrounds contain useful latent information, e.g., the sky in the aeroplane class. If this latent information can be learned, object-background ambiguity can be largely reduced and background can be suppressed effectively. In this paper, we propose the latent category learning (LCL) in large-scale cluttered conditions. LCL is an unsupervised learning method which requires only image-level class labels. First, we use the latent semantic analysis with semantic object representation to learn the latent categories, which represent objects, object parts or backgrounds. Second, to determine which category contains the target object, we propose a category selection strategy by evaluating each category's discrimination. Finally, we propose the online LCL for use in large-scale conditions. Evaluation on the challenging PASCAL Visual Object Class (VOC) 2007 and the large-scale imagenet large-scale visual recognition challenge 2013 detection data sets shows that the method can improve the annotation precision by 10% over previous methods. More importantly, we achieve the detection precision which outperforms previous results by a large margin and can be competitive to the supervised deformable part model 5.0 baseline on both data sets.

The determination of the constitutive parameters of a medium with application to a reinforced concrete pad

NASA Technical Reports Server (NTRS)

Poggio, A. J.; Burke, G. L.; Pennock, S. T.

1995-01-01

This report describes the experimental and analytical efforts performed to determine the constitutive parameters of a reinforced concrete pad on which an aircraft (the NASA Boeing 757) was parked while its internal electromagnetic environment was measured. This concrete pad is part of the Large Electromagnetic System-Level Illuminator (LESLI) test facility at the Phillips Laboratory, Kirtland Air Force Base, New Mexico. The relative dielectric constant, conductivity, index of refraction, and reflection coefficient have been determined over the frequency range of 0 to 300 MHz and are presented.

Root-shoot allometry of tropical forest trees determined in a large-scale aeroponic system.

PubMed

Eshel, Amram; Grünzweig, José M

2013-07-01

This study is a first step in a multi-stage project aimed at determining allometric relationships among the tropical tree organs, and carbon fluxes between the various tree parts and their environment. Information on canopy-root interrelationships is needed to improve understanding of above- and below-ground processes and for modelling of the regional and global carbon cycle. Allometric relationships between the sizes of different plant parts will be determined. Two tropical forest species were used in this study: Ceiba pentandra (kapok), a fast-growing tree native to South and Central America and to Western Africa, and Khaya anthotheca (African mahogany), a slower-growing tree native to Central and Eastern Africa. Growth and allometric parameters of 12-month-old saplings grown in a large-scale aeroponic system and in 50-L soil containers were compared. The main advantage of growing plants in aeroponics is that their root systems are fully accessible throughout the plant life, and can be fully recovered for harvesting. The expected differences in shoot and root size between the fast-growing C. pentandra and the slower-growing K. anthotheca were evident in both growth systems. Roots were recovered from the aeroponically grown saplings only, and their distribution among various diameter classes followed the patterns expected from the literature. Stem, branch and leaf allometric parameters were similar for saplings of each species grown in the two systems. The aeroponic tree growth system can be utilized for determining the basic allometric relationships between root and shoot components of these trees, and hence can be used to study carbon allocation and fluxes of whole above- and below-ground tree parts.

Steady state analysis of Boolean molecular network models via model reduction and computational algebra.

PubMed

Veliz-Cuba, Alan; Aguilar, Boris; Hinkelmann, Franziska; Laubenbacher, Reinhard

2014-06-26

A key problem in the analysis of mathematical models of molecular networks is the determination of their steady states. The present paper addresses this problem for Boolean network models, an increasingly popular modeling paradigm for networks lacking detailed kinetic information. For small models, the problem can be solved by exhaustive enumeration of all state transitions. But for larger models this is not feasible, since the size of the phase space grows exponentially with the dimension of the network. The dimension of published models is growing to over 100, so that efficient methods for steady state determination are essential. Several methods have been proposed for large networks, some of them heuristic. While these methods represent a substantial improvement in scalability over exhaustive enumeration, the problem for large networks is still unsolved in general. This paper presents an algorithm that consists of two main parts. The first is a graph theoretic reduction of the wiring diagram of the network, while preserving all information about steady states. The second part formulates the determination of all steady states of a Boolean network as a problem of finding all solutions to a system of polynomial equations over the finite number system with two elements. This problem can be solved with existing computer algebra software. This algorithm compares favorably with several existing algorithms for steady state determination. One advantage is that it is not heuristic or reliant on sampling, but rather determines algorithmically and exactly all steady states of a Boolean network. The code for the algorithm, as well as the test suite of benchmark networks, is available upon request from the corresponding author. The algorithm presented in this paper reliably determines all steady states of sparse Boolean networks with up to 1000 nodes. The algorithm is effective at analyzing virtually all published models even those of moderate connectivity. The problem for large Boolean networks with high average connectivity remains an open problem.

Steady state analysis of Boolean molecular network models via model reduction and computational algebra

PubMed Central

2014-01-01

Background A key problem in the analysis of mathematical models of molecular networks is the determination of their steady states. The present paper addresses this problem for Boolean network models, an increasingly popular modeling paradigm for networks lacking detailed kinetic information. For small models, the problem can be solved by exhaustive enumeration of all state transitions. But for larger models this is not feasible, since the size of the phase space grows exponentially with the dimension of the network. The dimension of published models is growing to over 100, so that efficient methods for steady state determination are essential. Several methods have been proposed for large networks, some of them heuristic. While these methods represent a substantial improvement in scalability over exhaustive enumeration, the problem for large networks is still unsolved in general. Results This paper presents an algorithm that consists of two main parts. The first is a graph theoretic reduction of the wiring diagram of the network, while preserving all information about steady states. The second part formulates the determination of all steady states of a Boolean network as a problem of finding all solutions to a system of polynomial equations over the finite number system with two elements. This problem can be solved with existing computer algebra software. This algorithm compares favorably with several existing algorithms for steady state determination. One advantage is that it is not heuristic or reliant on sampling, but rather determines algorithmically and exactly all steady states of a Boolean network. The code for the algorithm, as well as the test suite of benchmark networks, is available upon request from the corresponding author. Conclusions The algorithm presented in this paper reliably determines all steady states of sparse Boolean networks with up to 1000 nodes. The algorithm is effective at analyzing virtually all published models even those of moderate connectivity. The problem for large Boolean networks with high average connectivity remains an open problem. PMID:24965213

Theory of self-resonance after inflation. I. Adiabatic and isocurvature Goldstone modes

NASA Astrophysics Data System (ADS)

Hertzberg, Mark P.; Karouby, Johanna; Spitzer, William G.; Becerra, Juana C.; Li, Lanqing

2014-12-01

We develop a theory of self-resonance after inflation. We study a large class of models involving multiple scalar fields with an internal symmetry. For illustration, we often specialize to dimension-four potentials, but we derive results for general potentials. This is the first part of a two part series of papers. Here in Part 1 we especially focus on the behavior of long-wavelength modes, which are found to govern most of the important physics. Since the inflaton background spontaneously breaks the time-translation symmetry and the internal symmetry, we obtain Goldstone modes; these are the adiabatic and isocurvature modes. We find general conditions on the potential for when a large instability band exists for these modes at long wavelengths. For the adiabatic mode, this is determined by a sound speed derived from the time-averaged potential, while for the isocurvature mode, this is determined by a speed derived from a time-averaged auxiliary potential. Interestingly, we find that this instability band usually exists for one of these classes of modes, rather than both simultaneously. We focus on backgrounds that evolve radially in field space, as set up by inflation, and also mention circular orbits, as relevant to Q -balls. In Part 2 [M. P. Hertzberg et al., Phys. Rev. D 90, 123529 (2014)] we derive the central behavior from the underlying description of many-particle quantum mechanics, and introduce a weak breaking of the symmetry to study corrections to particle-antiparticle production from preheating.

Ensemble training to improve recognition using 2D ear

NASA Astrophysics Data System (ADS)

Middendorff, Christopher; Bowyer, Kevin W.

2009-05-01

The ear has gained popularity as a biometric feature due to the robustness of the shape over time and across emotional expression. Popular methods of ear biometrics analyze the ear as a whole, leaving these methods vulnerable to error due to occlusion. Many researchers explore ear recognition using an ensemble, but none present a method for designing the individual parts that comprise the ensemble. In this work, we introduce a method of modifying the ensemble shapes to improve performance. We determine how different properties of an ensemble training system can affect overall performance. We show that ensembles built from small parts will outperform ensembles built with larger parts, and that incorporating a large number of parts improves the performance of the ensemble.

A comparison of quality and utilization problems in large and small group practices.

PubMed

Gleason, S C; Richards, M J; Quinnell, J E

1995-12-01

Physicians practicing in large, multispecialty medical groups share an organizational culture that differs from that of physicians in small or independent practices. Since 1980, there has been a sharp increase in the size of multispecialty group practice organizations, in part because of increased efficiencies of large group practices. The greater number of physicians and support personnel in a large group practice also requires a relatively more sophisticated management structure. The efficiencies, conveniences, and management structure of a large group practice provide an optimal environment to practice medicine. However, a search of the literature found no data linking a large group practice environment to practice outcomes. The purpose of the study reported in this article was to determine if physicians in large practices have fewer quality and utilization problems than physicians in small or independent practices.

Spin determination at the Large Hadron Collider

NASA Astrophysics Data System (ADS)

Yavin, Itay

The quantum field theory describing the Electroweak sector demands some new physics at the TeV scale in order to unitarize the scattering of longitudinal W bosons. If this new physics takes the form of a scalar Higgs boson then it is hard to understand the huge hierarchy of scales between the Electroweak scale ˜ TeV and the Planck scale ˜ 1019 GeV. This is known as the Naturalness problem. Normally, in order to solve this problem, new particles, in addition to the Higgs boson, are required to be present in the spectrum below a few TeV. If such particles are indeed discovered at the Large Hadron Collider it will become important to determine their spin. Several classes of models for physics beyond the Electroweak scale exist. Determining the spin of any such newly discovered particle could prove to be the only means of distinguishing between these different models. In the first part of this thesis; we present a thorough discussion regarding such a measurement. We survey the different potentially useful channels for spin determination and a detailed analysis of the most promising channel is performed. The Littlest Higgs model offers a way to solve the Hierarchy problem by introduring heavy partners to Standard Model particles with the same spin and quantum numbers. However, this model is only good up to ˜ 10 TeV. In the second part of this thesis we present an extension of this model into a strongly coupled theory above ˜ 10 TeV. We use the celebrated AdS/CFT correspondence to calculate properties of the low-energy physics in terms of high-energy parameters. We comment on some of the tensions inherent to such a construction involving a large-N CFT (or equivalently, an AdS space).

Arabidopsis Thaliana Ecotypes With Differential Susceptibility To The Bacterial Pathogen Xylella fastidiosa

USDA-ARS?s Scientific Manuscript database

Pierce’s disease of grapes and almond leaf scorch are devastating diseases caused by the bacterium Xylella fastidiosa (Xf). To date, progress in determining the mechanisms of host plant susceptibility, tolerance or resistance has been slow, due in large part to the long generation time and limited a...

A Survey of Librarian Perceptions of Information Literacy Techniques

ERIC Educational Resources Information Center

Yearwood, Simone L.; Foasberg, Nancy M.; Rosenberg, Kenneth D.

2015-01-01

Teaching research competencies and information literacy is an integral part of the academic librarian's role. There has long been debate among librarians over what are the most effective methods of instruction for college students. Library Faculty members at a large urban university system were surveyed to determine their perceptions of the…

From Intuition to Science: Re-ED and Trauma-Informed Care

ERIC Educational Resources Information Center

Maikoetter, Michelle

2011-01-01

Nicholas Hobbs, a visionary in the field of psychology, believed strongly that how one defines a problem determines in large part the strategies that can be generated to solve it (Hobbs, 1982). He questioned the validity of psychiatric labels and other means of classification that pathologized children, believing that such approaches guided people…

PULSED SPLITLESS AND LARGE-VOLUME INJECTION IN CAPILLARY GAS CHROMATOGRAPHY MASS SPECTROMETRY FOR THE DETERMINATION OF ULTRA-TRACE LEVEL PESTICIDE RESIDUES

EPA Science Inventory

The possible presence of ultra-trace levels (sub- parts per trillion) of pesticides in pristine aquatic environments (e.g., alpine lakes) would raise questions regarding potential effects on biota. One hypothesis is that agricultural pesticides that are heavily applied in the San...

Improving Classroom Behavior through Effective Instruction: An Illustrative Program Example Using "SRA FLEX Literacy"

ERIC Educational Resources Information Center

Martella, Ronald C.; Marchand-Martella, Nancy E.

2015-01-01

Research has demonstrated a strong positive correlation between behavior problems and low academic achievement. Student success and/or failures are in large part determined by how well teachers provide effective instruction to their students. This article overviews key behavior-management approaches related to academic and behavioral success that…

The Impact of Discrimination on the Early Schooling Experiences of Children from Immigrant Families

ERIC Educational Resources Information Center

Adair, Jennifer Keys

2015-01-01

How the young children of immigrants experience their early school years may in large part determine their academic future and negatively affect their emotional, social, and mental development. Children benefit from a positive, supportive learning environment where their contributions are valued; many from immigrant families, however, experience…

Evaluating Federal Social Programs: Finding out What Works and What Does Not

ERIC Educational Resources Information Center

Muhlhausen, David B.

2012-01-01

Federal social programs are rarely evaluated to determine whether they are actually accomplishing their intended purposes. As part of its obligation to spend taxpayers' dollars wisely, Congress should mandate that experimental evaluations of every federal social program be conducted. The evaluations should be large-scale, multisite studies to…

Faculty Perceptions of Basic Skills Faculty Development

ERIC Educational Resources Information Center

Duffy, Michelle Moreau

2012-01-01

This study investigated the perceptions of faculty regarding why they choose to attend basic skills faculty development; what they choose to implement in their classrooms; and how they determine the effectiveness of the strategies selected. A survey was completed by 173 full and part-time faculty from a large, suburban single-campus community…

Characterization of (CA)n microsatellite repeats from large-insert clones.

PubMed

Litt, M; Browne, D

2001-05-01

The most laborious part of developing (CA)n microsatellite repeats as genetic markers is constructing DNA clones to permit determination of sequences flanking the microsatellites. When cosmids or large-insert phage clones are used as primary sources of (CA)n repeat markers, they have traditionally been subcloned into plasmid vectors such as pUC18 or M13 mp 18/19 cloning vectors to obtain fragments of suitable size for DNA sequencing. This unit presents an alternative approach whereby a set of degenerate sequencing primers that anneal directly to (CA)n microsatellites can be used to determine sequences that are inaccessible with vector-derived primers. Because the primers anneal to the repeat and not to the vector, they can be used with subclones containing inserts of several kilobases and should, in theory, always give sequence in the regions directly flanking the repeat. Degeneracy at the 3 end of each of these primers prevents elongation of primers that have annealed out-of-register. The most laborious part of developing (CA)n microsatellite repeats as genetic markers is constructing DNA clones to permit.

Geohydrology and water quality of the Roubidoux Aquifer, northeastern Oklahoma

USGS Publications Warehouse

Christenson, S.C.; Parkhurst, D.L.; Fairchild, R.W.

1990-01-01

The Roubidoux aquifer is an important source of freshwater for public supplies, commerce, industry, and rural water districts in northeastern Oklahoma. Ground-water withdrawals from the aquifer in 1981 were estimated to be 4.8 million gallons per day, of which about 90 percent was withdrawn in Ottawa County. Wells drilled at the beginning of the 20th century originally flowed at the land surface, but in 1981 water levels ranged from 22 to 471 feet below land surface. A large cone of depression has formed as a result of ground water withdrawals near Miami. Wells completed in the Roubidoux aquifer have yields that range from about 100 to more than 1,000 gallons per minute. An aquifer test and a digital ground-water flow model were used to estimate aquifer and confining-layer hydraulic characteristics. Using these methods, the transmissivity of the aquifer was estimated to be within a range of 400 to 700 square feet per day. The leakance of the confining layer was determined to be within a range from 0 to 0.13 per day, with a best estimate value in a range from 4.3 x 10-8 to 7.7 x 10-8 per day. Analyses of water samples collected as part of this study and of water-quality data from earlier work indicate that a large areal change in major-ion chemistry occurs in ground water in the Roubidoux aquifer in northeastern Oklahoma. The ground water in the easternmost part of the study unit has relatively small dissolved-solids concentrations (less than 200 milligrams per liter) with calcium, magnesium, and bicarbonate as the major ions. Ground water in the westernmost part of the study unit has relatively large dissolved-solids concentrations (greater than 800 milligrams per liter) with sodium and chloride as the major ions. A transition zone of intermediate sodium, chloride, and dissolved-solids concentrations exists between the easternmost and westernmost parts of the study unit. Three water-quality problems are apparent in the Roubidoux aquifer in northeast Oklahoma: (1) Contamination by mine water, (2) large concentrations of sodium and chloride, and (3) large radium-226 concentrations. Many wells in the mining area have been affected by mine-water contamination. At present (1990), all instances of ground-water contamination by mine water can be explained by faulty seals or leaky casings in wells that pass through the zone of mine workings and down to the Roubidoux aquifer. None of the data available to date demonstrate that mine water has migrated from the Boone Formation through the pores and fractures of the intervening geologic units to the Roubidoux aquifer. Ground water with large concentrations of sodium and chloride occurs at some depth throughout the study unit. In the eastern part of the study unit, chloride concentrations greater than 250 milligrams per liter are found at depths greater than approximately 1,200 to 1,500 feet. Data are too few to determine the depth to ground water with large concentrations of sodium and chloride in the southern and southwestern parts of the study unit. Large concentrations of gross-alpha radioactivity in ground water occur near the western edge of the transition zone. Generally, ground water with large concentrations of gross-alpha radioactivity was found to exceed the maximum contaminant level for radium-226. (available as photostat copy only)

Stress Free Temperature Testing and Residual Stress Calculations on Out-of-Autoclave Composites

NASA Technical Reports Server (NTRS)

Cox, Sarah; Tate, LaNetra C.; Danley, Susan; Sampson, Jeff; Taylor, Brian; Miller, Sandi

2012-01-01

Future launch vehicles will require the incorporation large composite parts that will make up primary and secondary components of the vehicle. NASA has explored the feasibility of manufacturing these large components using Out-of-Autoclave impregnated carbon fiber composite systems through many composites development projects. Most recently, the Composites for Exploration Project has been looking at the development of a 10 meter diameter fairing structure, similar in size to what will be required for a heavy launch vehicle. The development of new material systems requires the investigation of the material properties and the stress in the parts. Residual stress is an important factor to incorporate when modeling the stresses that a part is undergoing. Testing was performed to verify the stress free temperature with two-ply asymmetric panels. A comparison was done between three newly developed out of autoclave IM7 /Bismalieimide (BMI) systems. This paper presents the testing results and the analysis performed to determine the residual stress of the materials.

Stress Free Temperature Testing and Calculations on Out-of-Autoclave Composites

NASA Technical Reports Server (NTRS)

Cox, Sarah B.; Tate, LeNetra C.; Danley, Susan E.; Sampson, Jeffrey W.; Taylor, Brian J.; Sutter, James K.; Miller, Sandi G.

2013-01-01

Future launch vehicles will require the incorporation of large composite parts that will make up primary and secondary components of the vehicle. NASA has explored the feasibility of manufacturing these large components using Out-of-Autoclave impregnated carbon fiber composite systems through many composites development projects. Most recently, the Composites for Exploration Project has been looking at the development of a 10 meter diameter fairing structure, similar in size to what will be required for a heavy launch vehicle. The development of new material systems requires the investigation of the material properties and the stress in the parts. Residual stress is an important factor to incorporate when modeling the stresses that a part is undergoing. Testing was performed to verify the stress free temperature with two-ply asymmetric panels. A comparison was done between three newly developed out of autoclave IM7/Bismaleimide (BMI) systems. This paper presents the testing results and the analysis performed to determine the stress free temperature of the materials

Time use and physical activity in a specialised brain injury rehabilitation unit: an observational study.

PubMed

Hassett, Leanne; Wong, Siobhan; Sheaves, Emma; Daher, Maysaa; Grady, Andrew; Egan, Cara; Seeto, Carol; Hosking, Talia; Moseley, Anne

2018-04-18

To determine what is the use of time and physical activity in people undertaking inpatient rehabilitation in a specialised brain injury unit. To determine participants' level of independence related to the use of time and physical activity. Design: Cross-sectional observation study. Fourteen people [mean (SD) age 40 (15) years] with brain injuries undertaking inpatient rehabilitation. Participants were observed every 12 minutes over 5 days (Monday to Friday from 7:30 am until 7:30 pm) using a behaviour mapping tool. Observation of location, people present, body position and activity engaged in (both therapeutic and nontherapeutic). Functional Independence Measure (FIM) scores were determined for each participant. Participants spent a large part of their time alone (34%) in sedentary positions (83%) and in their bedrooms (48%) doing non-therapeutic activities (78%). There was a positive relationship between a higher level of independence (higher FIM score) and being observed in active body positions (r=0.60; p=0.03) and participating in physically active therapeutic activities (r=0.53; p=0.05). Similar to stroke units, inpatients in a specialised brain injury unit spend large parts of the day sedentary, alone and doing non-therapeutic activities. Strategies need to be evaluated to address this problem, particularly for people with greater physical dependence.

Geology and ground-water resources of Galveston County, Texas

USGS Publications Warehouse

Petitt, Ben McDowell; Winslow, Allen George

1957-01-01

Much additional ground water could be obtained from both the "Alta Loma" sand and the upper part of the Beaumont clay, especially in the northern and western parts of the county. Before large developments of supplies are planned, however, these areas should be explored by test drilling. The problems of well spacing and pumping rates should be thoroughly studied in order to determine the maximum development permitted by the ground-water supply. Current observations should be continued with special emphasis on the progress of salt-water encroachment.

A real-frequency solver for the Anderson impurity model based on bath optimization and cluster perturbation theory

NASA Astrophysics Data System (ADS)

Zingl, Manuel; Nuss, Martin; Bauernfeind, Daniel; Aichhorn, Markus

2018-05-01

Recently solvers for the Anderson impurity model (AIM) working directly on the real-frequency axis have gained much interest. A simple and yet frequently used impurity solver is exact diagonalization (ED), which is based on a discretization of the AIM bath degrees of freedom. Usually, the bath parameters cannot be obtained directly on the real-frequency axis, but have to be determined by a fit procedure on the Matsubara axis. In this work we present an approach where the bath degrees of freedom are first discretized directly on the real-frequency axis using a large number of bath sites (≈ 50). Then, the bath is optimized by unitary transformations such that it separates into two parts that are weakly coupled. One part contains the impurity site and its interacting Green's functions can be determined with ED. The other (larger) part is a non-interacting system containing all the remaining bath sites. Finally, the Green's function of the full AIM is calculated via coupling these two parts with cluster perturbation theory.

Influences of Institutional Structure, Policy, and Practice on Faculty Participation in Online Teaching

ERIC Educational Resources Information Center

Mazer, Vickie M.

2015-01-01

Online education is growing in response to demands of increased access, quality, and affordability. However, implementation and expansion are often challenged by faculty resistance, due in large part to perceived lack of quality and administrative support. This case study sought to determine how the presence or absence of quality elements, as…

Operations Research techniques in the management of large-scale reforestation programs

Treesearch

Joseph Buongiorno; D.E. Teeguarden

1978-01-01

A reforestation planning system for the Douglas-fir region of the Western United States is described. Part of the system is a simulation model to predict plantation growth and to determine economic thinning regimes and rotation ages as a function of site characteristics, initial density, reforestation costs, and management constraints. A second model estimates the...

Ignorance- versus Evidence-Based Decision Making: A Decision Time Analysis of the Recognition Heuristic

ERIC Educational Resources Information Center

Hilbig, Benjamin E.; Pohl, Rudiger F.

2009-01-01

According to part of the adaptive toolbox notion of decision making known as the recognition heuristic (RH), the decision process in comparative judgments--and its duration--is determined by whether recognition discriminates between objects. By contrast, some recently proposed alternative models predict that choices largely depend on the amount of…

Predictive Utility and Causal Influence of the Writing Self-Efficacy Beliefs of Elementary Students.

ERIC Educational Resources Information Center

Pajares, Frank; Valiante, Gio

According to self-efficacy theorists, people's judgments of what they can accomplish are influential arbiters in human agency and, as such, powerful determinants of their behavior. In large part, this is because these self-efficacy beliefs are said to act as mediators between other acknowledged influences on behavior, such as skill, ability,…

Going Public: Who Leaves a Large, Longstanding, and Widely Available Urban Voucher Program?

ERIC Educational Resources Information Center

Cowen, Joshua M.; Fleming, David J.; Witte, John F.; Wolf, Patrick J.

2012-01-01

This article contributes to research concerning the determinants of student mobility between public and private schools. The authors analyze a unique set of data collected as part of a new evaluation of Milwaukee's citywide voucher program. The authors find several important patterns. Students who switch from the private to the public sector were…

Prevalence of chronic atrophic gastritis in different parts of the world.

PubMed

Weck, Melanie Nicole; Brenner, Hermann

2006-06-01

Chronic atrophic gastritis (CAG) is a well-established precursor of intestinal gastric cancer, but epidemiologic data about its occurrence are sparse. We provide an overview on studies that examined the prevalence of CAG in different parts of the world. Articles containing data about the prevalence of chronic atrophic gastritis in unselected population samples and published until November 2005 were identified by searching the MEDLINE database. Furthermore, the references in the identified publications were screened for additional suitable studies. Studies comprising at least 50 subjects were included. Forty-one studies providing data on the prevalence of CAG in unselected population samples could be identified. CAG was determined by gastroscopy in 15 studies and by pepsinogen serum levels in 26 studies. Although results are difficult to compare due to the various definitions of CAG used, a strong increase with age, the lack of major gender differences, and strong variations between populations and population groups (in particular, relatively high rates in certain Asian populations) could be observed quite consistently. We conclude that CAG is relatively common among older adults in different parts of the world, but large variations exist. Large-scale international comparative studies with standardized methodology to determine CAG are needed to provide a coherent picture of the epidemiology of CAG in various populations. Noninvasive measurements of CAG by pepsinogen levels may be particularly suited for that purpose.

OPTICAL–NEAR-INFRARED PHOTOMETRIC CALIBRATION OF M DWARF METALLICITY AND ITS APPLICATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hejazi, N.; Robertis, M. M. De; Dawson, P. C., E-mail: nedahej@yorku.ca, E-mail: mmdr@yorku.ca, E-mail: pdawson@trentu.ca

2015-04-15

Based on a carefully constructed sample of dwarf stars, a new optical–near-infrared photometric calibration to estimate the metallicity of late-type K and early-to-mid-type M dwarfs is presented. The calibration sample has two parts; the first part includes 18 M dwarfs with metallicities determined by high-resolution spectroscopy and the second part contains 49 dwarfs with metallicities obtained through moderate-resolution spectra. By applying this calibration to a large sample of around 1.3 million M dwarfs from the Sloan Digital Sky Survey and 2MASS, the metallicity distribution of this sample is determined and compared with those of previous studies. Using photometric parallaxes, themore » Galactic heights of M dwarfs in the large sample are also estimated. Our results show that stars farther from the Galactic plane, on average, have lower metallicity, which can be attributed to the age–metallicity relation. A scarcity of metal-poor dwarf stars in the metallicity distribution relative to the Simple Closed Box Model indicates the existence of the “M dwarf problem,” similar to the previously known G and K dwarf problems. Several more complicated Galactic chemical evolution models which have been proposed to resolve the G and K dwarf problems are tested and it is shown that these models could, to some extent, mitigate the M dwarf problem as well.« less

The Large Area Crop Inventory Experiment (LACIE). Part 3: A systematic approach to the practical application of remote-sensing technology

NASA Technical Reports Server (NTRS)

Murphy, J. D.; Dideriksen, R. I.

1975-01-01

The application of remote sensing technology by the U.S. Department of Agriculture (USDA) is examined. The activities of the USDA Remote-Sensing User Requirement Task Force which include cataloging USDA requirements for earth resources data, determining those requirements that would return maximum benefits by using remote sensing technology and developing a plan for acquiring, processing, analyzing, and distributing data to satisfy those requirements are described. Emphasis is placed on the large area crop inventory experiment and its relationship to the task force.

Statistics on the parameters of nonisothermal ionospheric plasma in large mesospheric electric fields

NASA Astrophysics Data System (ADS)

Martynenko, S.; Rozumenko, V.; Tyrnov, O.; Manson, A.; Meek, C.

The large V/m electric fields inherent in the mesosphere play an essential role in lower ionospheric electrodynamics. They must be the cause of large variations in the electron temperature and the electron collision frequency at D region altitudes, and consequently the ionospheric plasma in the lower part of the D region undergoes a transition into a nonisothermal state. This study is based on the databases on large mesospheric electric fields collected with the 2.2-MHz radar of the Institute of Space and Atmospheric Studies, University of Saskatchewan, Canada (52°N geographic latitude, 60.4°N geomagnetic latitude) and with the 2.3-MHz radar of the Kharkiv V. Karazin National University (49.6°N geographic latitude, 45.6°N geomagnetic latitude). The statistical analysis of these data is presented in Meek, C. E., A. H. Manson, S. I. Martynenko, V. T. Rozumenko, O. F. Tyrnov, Remote sensing of mesospheric electric fields using MF radars, Journal of Atmospheric and Solar-Terrestrial Physics, in press. The large mesospheric electric fields is experimentally established to follow a Rayleigh distribution in the interval 0

Signatures of selection among sex-determining alleles of the honey bee.

PubMed

Hasselmann, Martin; Beye, Martin

2004-04-06

Patterns of DNA polymorphisms are a primary tool for dissecting signatures of selection; however, the underlying selective forces are poorly understood for most genes. A classical example of diversifying selection is the complementary sex-determining locus that is found in the very large insect order Hymenoptera (bees, wasps, ants, and sawflies). The gene responsible for sex determination, the complementary sex determiner (csd), has been most recently identified in the honey bee. Females are heterozygous at this locus. Males result when there is only one functional allele present, as a result of either homozygosity (fertilized eggs) or, more commonly, hemizygosity (unfertilized eggs). The homozygotes, diploid males, do not reproduce and have zero fitness, which implies positive selection in favor of rare alleles. Large differences in csd cDNA sequences within and between four populations were found that fall into two major groups, types I and II. Type I consists of several allelic lineages that were maintained over an extended period, an indication of balancing selection. Diversifying selection has operated on several confined parts of the protein, as shown by an excess of nonsynonymous differences. Elevated sequence differences indicate another selected part near a repeat region. These findings have general implications about the understanding of both the function of the multiallelic mechanism and the adaptive processes on the level of nucleotide sequences. Moreover, the first csd sequence data are a notable basis for the avoidance of diploid males in bee selection programs by allele-assisted breeding.

Presentation of an approach for the analysis of the mechanical response of propellant under a large spectrum of loadings: numerical and mechanical issues

NASA Astrophysics Data System (ADS)

Fanget, Alain

2009-06-01

Many authors claim that to understand the response of a propellant, specifically under quasi static and dynamic loading, the mesostructural morphology and the mechanical behaviour of each of its components have to be known. However the scale of the mechanical description of the behaviour of a propellant is relative to its heterogeneities and the wavelength of loading. The shorter it is, the more important the topological description of the material is. In our problems, involving the safety of energetic materials, the propellant can be subjected to a large spectrum of loadings. This presentation is divided into five parts. The first part describes the processes used to extract the information about the morphology of the meso-structure of the material and presents some results. The results, the difficulties and the perspectives for this part will be recalled. The second part determines the physical processes involved at this scale from experimental results. Taking into account the knowledge of the morphology, two ways have been chosen to describe the response of the material. One concerns the quasi static loading, the object of the third part, in which we show how we use the mesoscopic scale as a base of development to build constitutive models. The fourth part presents for low but dynamic loading the comparison between numerical analysis and experiments.

Factors Influencing Retention Among Part-Time Clinical Nursing Faculty.

PubMed

Carlson, Joanne S

This study sought to determine job characteristics influencing retention of part-time clinical nurse faculty teaching in pre-licensure nursing education. Large numbers of part-time faculty are needed to educate students in the clinical setting. Faculty retention helps maintain consistency and may positively influence student learning. A national sample of part-time clinical nurse faculty teaching in baccalaureate programs responded to a web-based survey. Respondents were asked to identify the primary reason for wanting or not wanting to continue working for a school of nursing (SON). Affinity for students, pay and benefits, support, and feeling valued were the top three reasons given for continuing to work at an SON. Conflicts with life and other job responsibilities, low pay, and workload were the top three reasons given for not continuing. Results from this study can assist nursing programs in finding strategies to help reduce attrition among part-time clinical faculty.

Monitoring of manufacturing processes in the automotive industry using indoor location system

NASA Astrophysics Data System (ADS)

Ionescu, LM; Belu, N.; Rachieru, N.; Mazăre, AG; Anghel, D.-C.

2016-08-01

This paper presents a method for locating the operators, equipment and parts using radio communications systems. Specifically there will be radio transceiver arranged in a network of active and passive radio receivers placed on personnel, equipment or parts. Based on a radio triangulation method, it is determined the location of the all resources and parts involved in manufacturing process. The transceivers communicate with each other via “routers” - also components of the network. Such a structure may extend over large distances even in indoor spaces where there are obstacles (walls between rooms). The location is done by determining the power of transmission signal for at least three end points. The receiver position is then transmitted over the network through routers, to a central server where all positions of the resources are centralized. Our solution is a non-invasive and low cost method for determining resource position in the factory. The system can be used for both resource planning production for current process more efficient and for further analysis of the movement of resources during previous processes with possible adjustments to the workspace and re-planning of resources for future processes.

Localization of the interband transitions in the bulk of the Brillouin zone of III–V compound crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sobolev, V. V., E-mail: sobolev@uni.udm.ru; Perevoshchikov, D. A.

2016-05-15

The localization of the transitions in the bulk of the Brillouin zone that form the main structures in the spectra of the imaginary part of the permittivity in the range up to ~7 eV for III–V semiconductors (AlSb, GaSb, InSb, and InAs) is determined using electron density functional theory. It is established that intense transitions occur not only in the vicinity of the high-symmetry axes of the Brillouin zone, but also in some specific large volumes of the irreducible part of the Brillouin zone.

Modern negligence law: Contribution of the medical cases.

PubMed

Hodgson, John

The law on medical negligence is part of the law of negligence generally. It has played a significant part in developing two key aspects of the law. There are special rules to determine the standard of care expected of experts when advising and solving problems, and medical cases have largely shaped the law. Although cases on causation may arise in any area, several of the key cases happen to be medical ones. They are particularly likely to assist where there are alternative causes, as it is often difficult to distinguish the effects of disease from those of inappropriate treatment.

Phalanx. Volume 47, Number 4

DTIC Science & Technology

2014-12-01

the official channels and processes of the national defense community. The principal venue for such discussions is the ...going to shape the Department for the next couple decades and determine in large part on whether or not we have a future that is defined more by...bar for analytic excellence, you have the opportunity to ensure a bright future for yourself and the MORS

A Survey of Video Game Players in a Public, Urban Research University

ERIC Educational Resources Information Center

Thirunarayanan, M. O.; Vilchez, Manuel; Abreu, Liala; Ledesma, Cyntianna; Lopez, Sandra

2010-01-01

A survey was conducted in a public, research university located in a large and diverse metropolitan area in the southeastern part of the USA. The purpose of the survey was to determine both the positive and negative personal, educational, social, and work related consequences of playing video games. Nearly two-thirds of the 203 participants in…

"Don't Let Our Dreams Die": Undocumented Students' Fight for Educational Equity in Tennessee

ERIC Educational Resources Information Center

Craven, Krista; Montero, Diana; Ramirez, Jazmin; Robles, Maria; Robles, Rodrigo

2017-01-01

Educational equity for undocumented immigrants has become a widely discussed issue in both the political and public realm of Tennessee, in large part as a result of the individual determination and collective resistance of undocumented youth living in the state. This article focuses on the ways in which undocumented immigrant youth in Tennessee…

Secondary Level Teachers: Supply and Demand in Liberia. Country Study No. 6.

ERIC Educational Resources Information Center

Ferns, George W.; And Others

This is one of a series of country studies (ED 045 613-20) concerned with the supply of secondary level teachers in English-speaking Africa. It attempts to analyze the problem of teacher supply within the context of the social and economic factors which largely determine its nature and govern potential solutions. The first part of the document…

Print and Non-Print Materials: Adapting for Classroom Use. The ACTFL Foreign Language Education Series, Vol. 10.

ERIC Educational Resources Information Center

Mollica, Anthony S.

It has been said that the classroom must be a multidimensional environment where learning takes place and students are encouraged to realize their own potential. How all the relationships between the student and the components of the environment are cultivated will in large part determine the effectiveness of the teaching-learning process. This…

Problems and Prospects of the Development of the Rural School in Russia

ERIC Educational Resources Information Center

Gur'ianova, M. P.

2009-01-01

It is well known that to a large extent, it is the young people of today who will determine the intellectual, economic, cultural, and spiritual face of rural Russia in the twenty-first century. Unless young people take part in the modernization of the economy and in its social development, the Russian countryside will not have a future. Among…

Ohio's timber harvest revealed in stumps

Treesearch

Kenneth L. Quigley

1955-01-01

Timber is an important resource in Ohio, and cutting records are an essential part of a forest resource appraisal. However, finding out just how much timber is cut in the State during any one year is a big job. Occasionally in the past, wood-using industries have been surveyed to determine the volume cut by species and product, but the variety of industries, the large...

A Large Pseudoautosomal Region on the Sex Chromosomes of the Frog Silurana tropicalis

PubMed Central

Bewick, Adam J.; Chain, Frédéric J.J.; Zimmerman, Lyle B.; Sesay, Abdul; Gilchrist, Michael J.; Owens, Nick D.L.; Seifertova, Eva; Krylov, Vladimir; Macha, Jaroslav; Tlapakova, Tereza; Kubickova, Svatava; Cernohorska, Halina; Zarsky, Vojtech; Evans, Ben J.

2013-01-01

Sex chromosome divergence has been documented across phylogenetically diverse species, with amphibians typically having cytologically nondiverged (“homomorphic”) sex chromosomes. With an aim of further characterizing sex chromosome divergence of an amphibian, we used “RAD-tags” and Sanger sequencing to examine sex specificity and heterozygosity in the Western clawed frog Silurana tropicalis (also known as Xenopus tropicalis). Our findings based on approximately 20 million genotype calls and approximately 200 polymerase chain reaction-amplified regions across multiple male and female genomes failed to identify a substantially sized genomic region with genotypic hallmarks of sex chromosome divergence, including in regions known to be tightly linked to the sex-determining region. We also found that expression and molecular evolution of genes linked to the sex-determining region did not differ substantially from genes in other parts of the genome. This suggests that the pseudoautosomal region, where recombination occurs, comprises a large portion of the sex chromosomes of S. tropicalis. These results may in part explain why African clawed frogs have such a high incidence of polyploidization, shed light on why amphibians have a high rate of sex chromosome turnover, and raise questions about why homomorphic sex chromosomes are so prevalent in amphibians. PMID:23666865

Testing an integral conceptual model of frailty.

PubMed

Gobbens, Robbert J; van Assen, Marcel A; Luijkx, Katrien G; Schols, Jos M

2012-09-01

This paper is a report of a study conducted to test three hypotheses derived from an integral conceptual model of frailty.   The integral model of frailty describes the pathway from life-course determinants to frailty to adverse outcomes. The model assumes that life-course determinants and the three domains of frailty (physical, psychological, social) affect adverse outcomes, the effect of disease(s) on adverse outcomes is mediated by frailty, and the effect of frailty on adverse outcomes depends on the life-course determinants. In June 2008 a questionnaire was sent to a sample of community-dwelling people, aged 75 years and older (n = 213). Life-course determinants and frailty were assessed using the Tilburg frailty indicator. Adverse outcomes were measured using the Groningen activity restriction scale, the WHOQOL-BREF and questions regarding healthcare utilization. The effect of seven self-reported chronic diseases was examined. Life-course determinants, chronic disease(s), and frailty together explain a moderate to large part of the variance of the seven continuous adverse outcomes (26-57%). All these predictors together explained a significant part of each of the five dichotomous adverse outcomes. The effect of chronic disease(s) on all 12 adverse outcomes was mediated at least partly by frailty. The effect of frailty domains on adverse outcomes did not depend on life-course determinants. Our finding that the adverse outcomes are differently and uniquely affected by the three domains of frailty (physical, psychological, social), and life-course determinants and disease(s), emphasizes the importance of an integral conceptual model of frailty. © 2011 Blackwell Publishing Ltd.

An interior-point method-based solver for simulation of aircraft parts riveting

NASA Astrophysics Data System (ADS)

Stefanova, Maria; Yakunin, Sergey; Petukhova, Margarita; Lupuleac, Sergey; Kokkolaras, Michael

2018-05-01

The particularities of the aircraft parts riveting process simulation necessitate the solution of a large amount of contact problems. A primal-dual interior-point method-based solver is proposed for solving such problems efficiently. The proposed method features a worst case polynomial complexity bound ? on the number of iterations, where n is the dimension of the problem and ε is a threshold related to desired accuracy. In practice, the convergence is often faster than this worst case bound, which makes the method applicable to large-scale problems. The computational challenge is solving the system of linear equations because the associated matrix is ill conditioned. To that end, the authors introduce a preconditioner and a strategy for determining effective initial guesses based on the physics of the problem. Numerical results are compared with ones obtained using the Goldfarb-Idnani algorithm. The results demonstrate the efficiency of the proposed method.

Temperature and Snowfall in Western Queen Maud Land Increasing Faster Than Climate Model Projections

NASA Astrophysics Data System (ADS)

Medley, B.; McConnell, J. R.; Neumann, T. A.; Reijmer, C. H.; Chellman, N.; Sigl, M.; Kipfstuhl, S.

2018-02-01

East Antarctic Ice Sheet (EAIS) mass balance is largely driven by snowfall. Recently, increased snowfall in Queen Maud Land led to years of EAIS mass gain. It is difficult to determine whether these years of enhanced snowfall are anomalous or part of a longer-term trend, reducing our ability to assess the mitigating impact of snowfall on sea level rise. We determine that the recent snowfall increases in western Queen Maud Land (QML) are part of a long-term trend (+5.2 ± 3.7% decade-1) and are unprecedented over the past two millennia. Warming between 1998 and 2016 is significant and rapid (+1.1 ± 0.7°C decade-1). Using these observations, we determine that the current accumulation and temperature increases in QML from an ensemble of global climate simulations are too low, which suggests that projections of the QML contribution to sea level rise are potentially overestimated with a reduced mitigating impact of enhanced snowfall in a warming world.

Temperature and Snowfall in Western Queen Maud Land Increasing Faster than Climate Model Projections

NASA Technical Reports Server (NTRS)

Medley, B.; McConnell, J. R.; Neumann, T. A.; Reijmer, C. H.; Chellman, N.; Sigl, M.; Kipfstuhl, S.

2017-01-01

East Antarctic Ice Sheet (EAIS) mass balance is largely driven by snowfall. Recently, increased snowfall in Queen Maud Land led to years of EAIS mass gain. It is difficult to determine whether these years of enhanced snowfall are anomalous or part of a longer-term trend, reducing our ability to assess the mitigating impact of snowfall on sea level rise. We determine that the recent snowfall increases in western Queen Maud Land (QML) are part of a long-term trend (+5.2 +/- 3.7% decade(exp -1)) and are unprecedented over the past two millennia. Warming between 1998 and 2016 is significant and rapid (+1.1 +/- 0.7 C decade(exp -1)). Using these observations, we determine that the current accumulation and temperature increases in QML from an ensemble of global climate simulations are too low, which suggests that projections of the QML contribution to sea level rise are potentially overestimated with a reduced mitigating impact of enhanced snowfall in a warming world.

On the existence and stability of liquid water on the surface of mars today.

PubMed

Kuznetz, L H; Gan, D C

2002-01-01

The recent discovery of high concentrations of hydrogen just below the surface of Mars' polar regions by Mars Odyssey has enlivened the debate about past or present life on Mars. The prevailing assumption prior to the discovery was that the liquid water essential for its existence is absent. That assumption was based largely on the calculation of heat and mass transfer coefficients or theoretical climate models. This research uses an experimental approach to determine the feasibility of liquid water under martian conditions, setting the stage for a more empirical approach to the question of life on Mars. Experiments were conducted in three parts: Liquid water's existence was confirmed by droplets observed under martian conditions in part 1; the evolution of frost melting on the surface of various rocks under martian conditions was observed in part 2; and the evaporation rate of water in Petri dishes under Mars-like conditions was determined and compared with the theoretical predictions of various investigators in part 3. The results led to the conclusion that liquid water can be stable for extended periods of time on the martian surface under present-day conditions.

On the existence and stability of liquid water on the surface of mars today

NASA Technical Reports Server (NTRS)

Kuznetz, L. H.; Gan, D. C.

2002-01-01

The recent discovery of high concentrations of hydrogen just below the surface of Mars' polar regions by Mars Odyssey has enlivened the debate about past or present life on Mars. The prevailing assumption prior to the discovery was that the liquid water essential for its existence is absent. That assumption was based largely on the calculation of heat and mass transfer coefficients or theoretical climate models. This research uses an experimental approach to determine the feasibility of liquid water under martian conditions, setting the stage for a more empirical approach to the question of life on Mars. Experiments were conducted in three parts: Liquid water's existence was confirmed by droplets observed under martian conditions in part 1; the evolution of frost melting on the surface of various rocks under martian conditions was observed in part 2; and the evaporation rate of water in Petri dishes under Mars-like conditions was determined and compared with the theoretical predictions of various investigators in part 3. The results led to the conclusion that liquid water can be stable for extended periods of time on the martian surface under present-day conditions.

The anatomy of a cluster IDP. Part 1: Carbon abundance, bulk chemistry, and mineralogy of fragments from L2008#5

NASA Technical Reports Server (NTRS)

Thomas, K. L.; Keller, L. P.; Klock, W.; Warren, J.; Blanford, G. E.; Mckay, David S.

1994-01-01

The objective of this study was to determine whether or not cluster particles are sufficiently homogeneous to enable observations from one fragment of the cluster to be extrapolated to the entire cluster. We report on the results of a consortium study of the fragments of a large cluster particle. Multiple fragments from one large cluster were distributed to several research groups and were subjected to a variety of mineralogical and chemical analyses including: SEM, TEM, ion probe, SXRF, noble gas measurements, and microprobe laser mass spectrometry of individual fragments.

The Optical Gravitational Lensing Experiment. Eclipsing Binary Stars in the Large Magellanic Cloud

NASA Astrophysics Data System (ADS)

Wyrzykowski, L.; Udalski, A.; Kubiak, M.; Szymanski, M.; Zebrun, K.; Soszynski, I.; Wozniak, P. R.; Pietrzynski, G.; Szewczyk, O.

2003-03-01

We present the catalog of 2580 eclipsing binary stars detected in 4.6 square degree area of the central parts of the Large Magellanic Cloud. The photometric data were collected during the second phase of the OGLE microlensing search from 1997 to 2000. The eclipsing objects were selected with the automatic search algorithm based on an artificial neural network. Basic statistics of eclipsing stars are presented. Also, the list of 36 candidates of detached eclipsing binaries for spectroscopic study and for precise LMC distance determination is provided. The full catalog is accessible from the OGLE Internet archive.

Determinants of GBP Recruitment to Toxoplasma gondii Vacuoles and the Parasitic Factors That Control It

PubMed Central

Virreira Winter, Sebastian; Niedelman, Wendy; Jensen, Kirk D.; Rosowski, Emily E.; Julien, Lindsay; Spooner, Eric; Caradonna, Kacey; Burleigh, Barbara A.; Saeij, Jeroen P. J.; Ploegh, Hidde L.; Frickel, Eva-Maria

2011-01-01

IFN-γ is a major cytokine that mediates resistance against the intracellular parasite Toxoplasma gondii. The p65 guanylate-binding proteins (GBPs) are strongly induced by IFN-γ. We studied the behavior of murine GBP1 (mGBP1) upon infection with T. gondii in vitro and confirmed that IFN-γ-dependent re-localization of mGBP1 to the parasitophorous vacuole (PV) correlates with the virulence type of the parasite. We identified three parasitic factors, ROP16, ROP18, and GRA15 that determine strain-specific accumulation of mGBP1 on the PV. These highly polymorphic proteins are held responsible for a large part of the strain-specific differences in virulence. Therefore, our data suggest that virulence of T. gondii in animals may rely in part on recognition by GBPs. However, phagosomes or vacuoles containing Trypanosoma cruzi did not recruit mGBP1. Co-immunoprecipitation revealed mGBP2, mGBP4, and mGBP5 as binding partners of mGBP1. Indeed, mGBP2 and mGBP5 co-localize with mGBP1 in T. gondii-infected cells. T. gondii thus elicits a cell-autonomous immune response in mice with GBPs involved. Three parasitic virulence factors and unknown IFN-γ-dependent host factors regulate this complex process. Depending on the virulence of the strains involved, numerous GBPs are brought to the PV as part of a large, multimeric structure to combat T. gondii. PMID:21931713

Student and Faculty Views on Process of Science Skills at a Large, Research-Intensive University

ERIC Educational Resources Information Center

Addis, Elizabeth A.; Powell-Coffman, Jo Anne

2018-01-01

The Association of American Colleges and Universities ranks multiple process of science (POS) skills among the top-10 skills employers seek in college graduates. As part of an effort to explore and align the emphasis on POS skills in our science departments, we sought three things: (a) to determine if faculty and students felt enough time was…

X-Ray Topographic Studies of Energetic Materials.

DTIC Science & Technology

1987-03-01

role of these defects in crystal growth and in the microplasticity of the solid. 1.1 Experimental Techniques The method chosen for the detailed...the electron microscope. The examinations can be readily extended to detailed studies of the microplasticity of the materials using stress/strain...the availability of large, high quality, single crystals. A considerable part of the initial contract was devoted to the determination of conditions

Sine Qua Non: Indispensable Resources for Ed Tech Professionals. Part 1: Educational Technology

ERIC Educational Resources Information Center

Conley, Kate

2004-01-01

Because the field of educational technology is so broad and dynamic, it is extremely difficult to find time to keep up with the best practices, current research, and innovative ideas. In an effort to help readers keep up their knowledge of the field and to determine some of the most interesting and useful resources to date, a large body of…

Naval Recruit Classification Tests As Predictors of Performance in 87 Class "A" Enlisted Schools (1964-1966). Final Report.

ERIC Educational Resources Information Center

Thomas, Edmund D.

Scores earned on the Navy's enlisted classification tests determine, in large part, the type of job specialty training a recruit will receive. About 50% of recruits qualify for academic training in Basic Class "A" level schools. How well the classification tests predict performance in these schools is important from both a cost and a…

Large Deployable Reflector (LDR) thermal characteristics

NASA Technical Reports Server (NTRS)

Miyake, R. N.; Wu, Y. C.

1988-01-01

The thermal support group, which is part of the lightweight composite reflector panel program, developed thermal test and analysis evaluation tools necessary to support the integrated interdisciplinary analysis (IIDA) capability. A detailed thermal mathematical model and a simplified spacecraft thermal math model were written. These models determine the orbital temperature level and variation, and the thermally induced gradients through and across a panel, for inclusion in the IIDA.

Monitoring the Future National Survey Results on Drug Use, 1975-2013. Volume 1, Secondary School Students

ERIC Educational Resources Information Center

Johnston, Lloyd D.; O'Malley, Patrick M.; Bachman, Jerald G.; Schulenberg, John E.; Miech, Richard A.

2014-01-01

Substance use is a leading cause of preventable morbidity and mortality, and is in large part why people in the U.S. have the highest probability among industrialized nations of dying by age 50. Substance use deserves our sustained attention. It is also an important determinant of many social ills including child and spouse abuse, violence more…

Motor Flow Instabilities - Part 1

DTIC Science & Technology

2004-01-01

by the flow, the structure motions (as possibly affecting the mean and unsteady flows). Finally, the model should be able: a) to propagate the...combustion responses function determinations, Dedicated models for combustion mechanisms and fluid- structure couplings, Dedicated and documented test...associated with these large motors (recall that f1L ≈ a/2L) rendered such oscillations undesirable since they were able to couple to the structural modes

Methodology and significance of studies of atmospheric deposition in highway runoff

USGS Publications Warehouse

Colman, John A.; Rice, Karen C.; Willoughby, Timothy C.

2001-01-01

Atmospheric deposition and the processes that are involved in causing and altering atmospheric deposition in relation to highway surfaces and runoff were evaluated nationwide. Wet deposition is more easily monitored than dry deposition, and data on wet deposition are available for major elements and water properties (constituents affecting acid deposition) from the inter-agency National Atmospheric Deposition Program/ National Trends Network (NADP/NTN). Many trace constituents (metals and organic compounds) of interest in highway runoff loads, however, are not included in the NADP/NTN. Dry deposition, which constitutes a large part of total atmospheric deposition for many constituents in highway runoff loads, is difficult to monitor accurately. Dry-deposition rates are not widely available.Many of the highway-runoff investigations that have addressed atmospheric-deposition sources have had flawed investigative designs or problems with methodology. Some results may be incorrect because of reliance on time-aggregated data collected during a period of changing atmospheric emissions. None of the investigations used methods that could accurately quantify the part of highway runoff load that can be attributed to ambient atmospheric deposition. Lack of information about accurate ambient deposition rates and runoff loads was part of the problem. Samples collected to compute the rates and loads were collected without clean-sampling methods or sampler protocols, and without quality-assurance procedures that could validate the data. Massbudget calculations comparing deposition and runoff did not consider loss of deposited material during on-highway processing. Loss of deposited particles from highway travel lanes could be large, as has been determined in labeled particle studies, because of resuspension caused by turbulence from passing traffic. Although a cause of resuspension of large particles, traffic turbulence may increase the rate of deposition for small particles and gases by impaction, especially during precipitation periods.Ultimately, traffic and road maintenance may be determined to be the source of many constituents measured in highway runoff previously attributed to ambient atmospheric deposition. An investigative design using tracers of ambient deposition that are not present in highway traffic sources could determine conclusively what fraction of highway runoff load is contributed by ambient atmospheric deposition.

Benefit from NASA

NASA Image and Video Library

1995-01-01

Digital data matrix, used to identify the millions of Space Shuttle parts, is being commercialized to make barcoding tamper resistant and invisible to the naked eye. These codes are applied directly to the product regardless of shape, size or color. The markings can range from as small as four microns to as large as two square feet. Using the Vericode Symbol which include such details as the manufacturer, serial numbers, the lot number of the parent material, design changes, special processing to which the part was subjected-everything needed to determine accurately and automatically, the extent of the recall needed, which might be a couple of hundred cars instead of tens of thousands.

Chiral fluctuations in MnSi above the Curie temperature.

PubMed

Roessli, B; Böni, P; Fischer, W E; Endoh, Y

2002-06-10

Polarized neutrons are used to determine the antisymmetric part of the magnetic susceptibility in noncentrosymmetric MnSi. The paramagnetic fluctuations are found to be incommensurate with the chemical lattice and to have a chiral character. We argue that antisymmetric interactions must be taken into account to properly describe the critical dynamics in MnSi above T(C). The possibility of directly measuring the polarization dependent part of the dynamical susceptibility in a large class of compounds by polarized inelastic neutron scattering is outlined as it can yield evidence for antisymmetric interactions such as spin-orbit coupling in metals as well as in insulators.

Strength of the repulsive part of the interatomic potential determines fragility in metallic liquids

NASA Astrophysics Data System (ADS)

Pueblo, Christopher E.; Sun, Minhua; Kelton, K. F.

2017-08-01

The dynamical behaviour of liquids is frequently characterized by the fragility, which can be defined from the temperature dependence of the shear viscosity, η (ref. ). For a strong liquid, the activation energy for η changes little with cooling towards the glass transition temperature, Tg. The change is much greater in fragile liquids, with the activation energy becoming very large near Tg. While fragility is widely recognized as an important concept--believed, for example, to play an important role in glass formation--the microscopic origin of fragility is poorly understood. Here, we present new experimental evidence showing that fragility reflects the strength of the repulsive part of the interatomic potential, which can be determined from the steepness of the pair distribution function near the hard-sphere cutoff. On the basis of an analysis of scattering data from ten different metallic alloy liquids, we show that stronger liquids have steeper repulsive potentials.

Control of abdominal muscles by brain stem respiratory neurons in the cat

NASA Technical Reports Server (NTRS)

Miller, Alan D.; Ezure, Kazuhisa; Suzuki, Ichiro

1985-01-01

The nature of the control of abdominal muscles by the brain stem respiratory neurons was investigated in decerebrate unanesthetized cats. First, it was determined which of the brain stem respiratory neurons project to the lumbar cord (from which the abdominal muscles receive part of their innervation), by stimulating the neurons monopolarly. In a second part of the study, it was determined if lumbar-projecting respiratory neurons make monosynaptic connections with abdominal motoneurons; in these experiments, discriminate spontaneous spikes of antidromically acivated expiratory (E) neurons were used to trigger activity from both L1 and L2 nerves. A large projection was observed from E neurons in the caudal ventral respiratory group to the contralateral upper lumber cord. However, cross-correlation experiments found only two (out of 47 neuron pairs tested) strong monosynaptic connections between brain stem neurons and abdominal motoneurons.

AISI/DOE Technology Roadmap Program: Cold Work Embrittlement of Interstitial Free Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

John T Bowker; Pierre Martin

2002-10-31

This work addresses the issues of measurement of secondary cold work embrittlement (SCWE) of an IF steel in deep-drawn parts using laboratory tests, and its correlation with real part fracture. It aimed at evaluating the influence of the steel chemistry and processing condition, microstructure, and test conditions, on SCWE as well as the effect of SCWE on fatigue properties. Size 6-in. cups produced with various draw ratios or trimmed at different heights were tested to determine the ductile-to-brittle-transition temperature (DBTT) as a function of strain. The 2-in. cup/expansion test, bend test and fracture of notched specimens were also used tomore » generate information complementary to that provided by the 6-inch cup/expansion test. The relationship between laboratory tests and fracture in real parts was established by testing large-scale parts. The fatigue behavior was investigated in the as-rolled and deep drawn (high stain) conditions, using prestrained specimens taken from the wall of a formed part.« less

Photogrammetric Technique for Center of Gravity Determination

NASA Technical Reports Server (NTRS)

Jones, Thomas W.; Johnson, Thomas H.; Shemwell, Dave; Shreves, Christopher M.

2012-01-01

A new measurement technique for determination of the center of gravity (CG) for large scale objects has been demonstrated. The experimental method was conducted as part of an LS-DYNA model validation program for the Max Launch Abort System (MLAS) crew module. The test was conducted on the full scale crew module concept at NASA Langley Research Center. Multi-camera photogrammetry was used to measure the test article in several asymmetric configurations. The objective of these measurements was to provide validation of the CG as computed from the original mechanical design. The methodology, measurement technique, and measurement results are presented.

Wavefront error sensing

NASA Technical Reports Server (NTRS)

Tubbs, Eldred F.

1986-01-01

A two-step approach to wavefront sensing for the Large Deployable Reflector (LDR) was examined as part of an effort to define wavefront-sensing requirements and to determine particular areas for more detailed study. A Hartmann test for coarse alignment, particularly segment tilt, seems feasible if LDR can operate at 5 microns or less. The direct measurement of the point spread function in the diffraction limited region may be a way to determine piston error, but this can only be answered by a detailed software model of the optical system. The question of suitable astronomical sources for either test must also be addressed.

Metrology of Large Parts. Chapter 5

NASA Technical Reports Server (NTRS)

Stahl, H. Philip

2012-01-01

As discussed in the first chapter of this book, there are many different methods to measure a part using optical technology. Chapter 2 discussed the use of machine vision to measure macroscopic features such as length and position, which was extended to the use of interferometry as a linear measurement tool in chapter 3, and laser or other trackers to find the relation of key points on large parts in chapter 4. This chapter looks at measuring large parts to optical tolerances in the sub-micron range using interferometry, ranging, and optical tools discussed in the previous chapters. The purpose of this chapter is not to discuss specific metrology tools (such as interferometers or gauges), but to describe a systems engineering approach to testing large parts. Issues such as material warpage and temperature drifts that may be insignificant when measuring a part to micron levels under a microscope, as will be discussed in later chapters, can prove to be very important when making the same measurement over a larger part. In this chapter, we will define a set of guiding principles for successfully overcoming these challenges and illustrate the application of these principles with real world examples. While these examples are drawn from specific large optical testing applications, they inform the problems associated with testing any large part to optical tolerances. Manufacturing today relies on micrometer level part performance. Fields such as energy and transportation are demanding higher tolerances to provide increased efficiencies and fuel savings. By looking at how the optics industry approaches sub-micrometer metrology, one can gain a better understanding of the metrology challenges for any larger part specified to micrometer tolerances. Testing large parts, whether optical components or precision structures, to optical tolerances is just like testing small parts, only harder. Identical with what one does for small parts, a metrologist tests large parts and optics in particular to quantify their mechanical properties (such as dimensions, mass, etc); their optical prescription or design (i.e. radius of curvature, conic constant, vertex location, size); and their full part shape. And, just as with small parts, a metrologist accomplishes these tests using distance measuring instruments such as tape measures, inside micrometers, coordinate measuring machines, distance measuring interferometers; angle measuring instruments such as theodolites, autocollimators; and surface measuring instruments including interferometers, stylus profilers, interference microscopes, photogrammetric cameras, or other tools. However, while the methodology may be similar, it is more difficult to test a large object for the simple reason that most metrologists do not have the necessary intuition. The skills used to test small parts or optics in a laboratory do not extrapolate to testing large parts in an industrial setting any more than a backyard gardener might successfully operate a farm. But first, what is a large part? A simple definition might be the part's size or diameter. For optics and diffuse surface parts alike, the driving constraint is ability to illuminate the part's surface. For reflective convex mirrors, large is typically anything greater than 1 meter. But, for refractive optics, flats or convex mirrors, large is typically greater than 0.5 meter. While a size definition is simple, it may be less than universal. A more nuanced definition might be that a large part is any component which cannot be easily tested in a standard laboratory environment, on a standard vibration isolated table using standard laboratory infrastructure. A micro-switch or a precision lens might be easily measured to nanometer levels under a microscope in a lab, but a power turbine spline or a larger telescope mirror will not fit under that microscope and may not even fit on the table.

Afghanistan: Post-Taliban Governance, Security, and U.S. Policy

DTIC Science & Technology

2010-10-19

Bank (ADB) has also been playing a major role in Afghanistan. One of its projects in Afghanistan was funding the paving of a road from Qandahar to...freight railway ( in conjunction with the Asian Development Bank project above); and a road from the project to Kabul. However, work on the mine...conditions on the ground, as determined, in large part, by a formal DOD-led review of the Afghanistan

Strategic Challenges of China-Africa New Partnership

DTIC Science & Technology

2007-03-30

determined to pursue its national interests that include economic growth, to support a large population and enhance its global relevance. Its rapid...economic growth has increased its hunger for energy, raw materials, market and diplomatic relevance to sustain its power. A key region that China...to eradicate poverty and place their countries …on a part of sustained economic growth...” African leaders 2 evolved the New Partnership for

Simulation of crack propagation in rock in plasma blasting technology

NASA Astrophysics Data System (ADS)

Ikkurthi, V. R.; Tahiliani, K.; Chaturvedi, S.

Plasma Blasting Technology (PBT) involves the production of a pulsed electrical discharge by inserting a blasting probe in a water-filled cavity drilled in a rock, which produces shocks or pressure waves in the water. These pulses then propagate into the rock, leading to fracture. In this paper, we present the results of two-dimensional hydrodynamic simulations using the SHALE code to study crack propagation in rock. Three separate issues have been examined. Firstly, assuming that a constant pressure P is maintained in the cavity for a time τ , we have determined the P- τ curve that just cracks a given rock into at least two large-sized parts. This study shows that there exists an optimal pressure level for cracking a given rock-type and geometry. Secondly, we have varied the volume of water in which the initial energy E is deposited, which corresponds to different initial peak pressures Ppeak. We have determined the E- Ppeak curve that just breaks the rock into four large-sized parts. It is found that there must be an optimal Ppeak that lowers the energy consumption, but with acceptable probe damage. Thirdly, we have attempted to identify the dominant mechanism of rock fracture. We also highlight some numerical errors that must be kept in mind in such simulations.

Qaharir Field, Oman: A textbook case

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Dell, P.M.

1995-12-31

Qaharir Field is located in the southern part of the Sultanate of Oman. Like several fields in South Oman, it produces a light oil with very little solution gas. Qaharir Field contains a large depletion reservoir and several natural water drive reservoirs. There is, therefore, a large variation in the primary recovery efficiencies. A recent petroleum engineering review of this field determined the reservoir drive mechanisms and provided a basis for further development plans. This review of Qaharir Field demonstrates the application of conventional reservoir engineering tools to gain an understanding of the reservoir in sufficient detail to select andmore » plan the next development objectives.« less

Scramjet test flow reconstruction for a large-scale expansion tube, Part 2: axisymmetric CFD analysis

NASA Astrophysics Data System (ADS)

Gildfind, D. E.; Jacobs, P. A.; Morgan, R. G.; Chan, W. Y. K.; Gollan, R. J.

2018-07-01

This paper presents the second part of a study aiming to accurately characterise a Mach 10 scramjet test flow generated using a large free-piston-driven expansion tube. Part 1 described the experimental set-up, the quasi-one-dimensional simulation of the full facility, and the hybrid analysis technique used to compute the nozzle exit test flow properties. The second stage of the hybrid analysis applies the computed 1-D shock tube flow history as an inflow to a high-fidelity two-dimensional-axisymmetric analysis of the acceleration tube. The acceleration tube exit flow history is then applied as an inflow to a further refined axisymmetric nozzle model, providing the final nozzle exit test flow properties and thereby completing the analysis. This paper presents the results of the axisymmetric analyses. These simulations are shown to closely reproduce experimentally measured shock speeds and acceleration tube static pressure histories, as well as nozzle centreline static and impact pressure histories. The hybrid scheme less successfully predicts the diameter of the core test flow; however, this property is readily measured through experimental pitot surveys. In combination, the full test flow history can be accurately determined.

Scramjet test flow reconstruction for a large-scale expansion tube, Part 2: axisymmetric CFD analysis

NASA Astrophysics Data System (ADS)

Gildfind, D. E.; Jacobs, P. A.; Morgan, R. G.; Chan, W. Y. K.; Gollan, R. J.

2017-11-01

This paper presents the second part of a study aiming to accurately characterise a Mach 10 scramjet test flow generated using a large free-piston-driven expansion tube. Part 1 described the experimental set-up, the quasi-one-dimensional simulation of the full facility, and the hybrid analysis technique used to compute the nozzle exit test flow properties. The second stage of the hybrid analysis applies the computed 1-D shock tube flow history as an inflow to a high-fidelity two-dimensional-axisymmetric analysis of the acceleration tube. The acceleration tube exit flow history is then applied as an inflow to a further refined axisymmetric nozzle model, providing the final nozzle exit test flow properties and thereby completing the analysis. This paper presents the results of the axisymmetric analyses. These simulations are shown to closely reproduce experimentally measured shock speeds and acceleration tube static pressure histories, as well as nozzle centreline static and impact pressure histories. The hybrid scheme less successfully predicts the diameter of the core test flow; however, this property is readily measured through experimental pitot surveys. In combination, the full test flow history can be accurately determined.

The analysis of bottom forming process for hybrid heating device

NASA Astrophysics Data System (ADS)

Bałon, Paweł; Świątoniowski, Andrzej; Kiełbasa, Bartłomiej

2017-10-01

In this paper the authors present an unusual method for bottom forming applicable for various industrial purposes including the manufacture of water heaters or pressure equipment. This method allows for the fabrication of the bottom of a given piece of stainless steel into a pre-determined shape conforming to the DIN standard which determines the most advantageous dimensions for the bottom cross section in terms of working pressure loading. The authors checked the validity of the method in a numerical and experimental way generating a tool designed to produce bottoms of specified geometry. Many problems are encountered during the design and production of parts, especially excessive sheet wrinkling over a large area of the part. The experiment showed that a lack of experience and numerical analysis in the design of such elements would result in the production of highly wrinkled parts. This defect would render the parts impossible to assemble with the cylindrical part. Many tool shops employ a method for drawing elements with a spherical surface which involves additional spinning, stamping, and grading operations, which greatly increases the cost of parts production. The authors present and compare two forming methods for spherical and parabolic objects, and experimentally confirm the validity of the sheet reversing method with adequate pressure force. The applied method produces parts in one drawing operation and in a following operation that is based on laser or water cutting to obtain a round blank. This reduces the costs of tooling manufacturing by requiring just one tool which can be placed on any hydraulic press with a minimum force of 2 000 kN.

Mapping of compositional properties of coal using isometric log-ratio transformation and sequential Gaussian simulation - A comparative study for spatial ultimate analyses data.

PubMed

Karacan, C Özgen; Olea, Ricardo A

2018-03-01

Chemical properties of coal largely determine coal handling, processing, beneficiation methods, and design of coal-fired power plants. Furthermore, these properties impact coal strength, coal blending during mining, as well as coal's gas content, which is important for mining safety. In order for these processes and quantitative predictions to be successful, safer, and economically feasible, it is important to determine and map chemical properties of coals accurately in order to infer these properties prior to mining. Ultimate analysis quantifies principal chemical elements in coal. These elements are C, H, N, S, O, and, depending on the basis, ash, and/or moisture. The basis for the data is determined by the condition of the sample at the time of analysis, with an "as-received" basis being the closest to sampling conditions and thus to the in-situ conditions of the coal. The parts determined or calculated as the result of ultimate analyses are compositions, reported in weight percent, and pose the challenges of statistical analyses of compositional data. The treatment of parts using proper compositional methods may be even more important in mapping them, as most mapping methods carry uncertainty due to partial sampling as well. In this work, we map the ultimate analyses parts of the Springfield coal from an Indiana section of the Illinois basin, USA, using sequential Gaussian simulation of isometric log-ratio transformed compositions. We compare the results with those of direct simulations of compositional parts. We also compare the implications of these approaches in calculating other properties using correlations to identify the differences and consequences. Although the study here is for coal, the methods described in the paper are applicable to any situation involving compositional data and its mapping.

Water withdrawals in the Black Warrior-Tombigbee Basin and Alcorn County, Mississippi, 1985-87

USGS Publications Warehouse

Barber, N.L.

1991-01-01

Public-supply and industrial water withdrawals were inventoried for the Mississippi part of the Black Warrior-Tombigbee Basin and for Alcorn County, Mississippi. The study area, located in the northeastern part of the State, is largely forested or agricultural land, with some industries near the larger towns. A water-resource capacity analysis was done to determine a risk rating for each inventoried facility, evaluating the likelihood of the facility exceeding the capacity of its current source of water at the existing level of use. Published reports and potentiometric maps were used in this analysis to determine the source capacity and the effects withdrawals have had on each water source. The public-supply and industrial water withdrawals in the basin are from ground water, with the exception of the city of Columbus. About 97 percent of the total withdrawal of 80 million gallons per day is from ground water. Water-supply systems in three areas were determined to have a high risk of exceeding the water-resource capacity: the Tupelo-Lee County area, the West Point (Clay County) area, and the Starkville (Oktibbeha County) area.

A Computational Approach to Qualitative Analysis in Large Textual Datasets

PubMed Central

Evans, Michael S.

2014-01-01

In this paper I introduce computational techniques to extend qualitative analysis into the study of large textual datasets. I demonstrate these techniques by using probabilistic topic modeling to analyze a broad sample of 14,952 documents published in major American newspapers from 1980 through 2012. I show how computational data mining techniques can identify and evaluate the significance of qualitatively distinct subjects of discussion across a wide range of public discourse. I also show how examining large textual datasets with computational methods can overcome methodological limitations of conventional qualitative methods, such as how to measure the impact of particular cases on broader discourse, how to validate substantive inferences from small samples of textual data, and how to determine if identified cases are part of a consistent temporal pattern. PMID:24498398

The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components.

PubMed

Tammas-Williams, S; Withers, P J; Todd, I; Prangnell, P B

2017-08-04

Without post-manufacture HIPing the fatigue life of electron beam melting (EBM) additively manufactured parts is currently dominated by the presence of porosity, exhibiting large amounts of scatter. Here we have shown that the size and location of these defects is crucial in determining the fatigue life of EBM Ti-6Al-4V samples. X-ray computed tomography has been used to characterise all the pores in fatigue samples prior to testing and to follow the initiation and growth of fatigue cracks. This shows that the initiation stage comprises a large fraction of life (>70%). In these samples the initiating defect was often some way from being the largest (merely within the top 35% of large defects). Using various ranking strategies including a range of parameters, we found that when the proximity to the surface and the pore aspect ratio were included the actual initiating defect was within the top 3% of defects ranked most harmful. This lays the basis for considering how the deposition parameters can be optimised to ensure that the distribution of pores is tailored to the distribution of applied stresses in additively manufactured parts to maximise the fatigue life for a given loading cycle.

Mass Loss from Dusty AGB and Red Supergiant Stars in the Magellanic Clouds and in the Galaxy

NASA Astrophysics Data System (ADS)

Sargent, Benjamin A.; Srinivasan, Sundar; Meixner, Margaret; Kastner, Joel

2016-01-01

Asymptotic giant branch (AGB) and red supergiant (RSG) stars are evolved stars that eject large parts of their mass in outflows of dust and gas. As part of an ongoing effort to measure mass loss from evolved stars in our Galaxy and in the Magellanic Clouds, we are modeling mass loss from AGB and RSG stars in these galaxies. Our approach is twofold. We pursue radiative transfer modeling of the spectral energy distributions (SEDs) of AGB and RSG stars in the Large Magellanic Cloud (LMC), in the Small Magellanic Cloud (SMC), and in the Galactic bulge and in globular clusters of the Milky Way. We are also constructing detailed dust opacity models of AGB and RSG stars in these galaxies for which we have infrared spectra; e.g., from the Spitzer Space Telescope Infrared Spectrograph (IRS). Our sample of infrared spectra largely comes from Spitzer-IRS observations. The detailed dust modeling of spectra informs our choice of dust properties to use in radiative transfer modeling of SEDs. We seek to determine how mass loss from these evolved stars depends upon the metallicity of their host environments. BAS acknowledges funding from NASA ADAP grant NNX15AF15G.

Climate variability rather than overstocking causes recent large scale cover changes of Tibetan pastures.

PubMed

Lehnert, L W; Wesche, K; Trachte, K; Reudenbach, C; Bendix, J

2016-04-13

The Tibetan Plateau (TP) is a globally important "water tower" that provides water for nearly 40% of the world's population. This supply function is claimed to be threatened by pasture degradation on the TP and the associated loss of water regulation functions. However, neither potential large scale degradation changes nor their drivers are known. Here, we analyse trends in a high-resolution dataset of grassland cover to determine the interactions among vegetation dynamics, climate change and human impacts on the TP. The results reveal that vegetation changes have regionally different triggers: While the vegetation cover has increased since the year 2000 in the north-eastern part of the TP due to an increase in precipitation, it has declined in the central and western parts of the TP due to rising air temperature and declining precipitation. Increasing livestock numbers as a result of land use changes exacerbated the negative trends but were not their exclusive driver. Thus, we conclude that climate variability instead of overgrazing has been the primary cause for large scale vegetation cover changes on the TP since the new millennium. Since areas of positive and negative changes are almost equal in extent, pasture degradation is not generally proceeding.

Security aspects of space operations data

NASA Technical Reports Server (NTRS)

Schmitz, Stefan

1993-01-01

This paper deals with data security. It identifies security threats to European Space Agency's (ESA) In Orbit Infrastructure Ground Segment (IOI GS) and proposes a method of dealing with its complex data structures from the security point of view. It is part of the 'Analysis of Failure Modes, Effects Hazards and Risks of the IOI GS for Operations, including Backup Facilities and Functions' carried out on behalf of the European Space Operations Center (ESOC). The security part of this analysis has been prepared with the following aspects in mind: ESA's large decentralized ground facilities for operations, the multiple organizations/users involved in the operations and the developments of ground data systems, and the large heterogeneous network structure enabling access to (sensitive) data which does involve crossing organizational boundaries. An IOI GS data objects classification is introduced to determine the extent of the necessary protection mechanisms. The proposal of security countermeasures is oriented towards the European 'Information Technology Security Evaluation Criteria (ITSEC)' whose hierarchically organized requirements can be directly mapped to the security sensitivity classification.

Quantification of uncertainty in machining operations for on-machine acceptance.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Claudet, Andre A.; Tran, Hy D.; Su, Jiann-Chemg

2008-09-01

Manufactured parts are designed with acceptance tolerances, i.e. deviations from ideal design conditions, due to unavoidable errors in the manufacturing process. It is necessary to measure and evaluate the manufactured part, compared to the nominal design, to determine whether the part meets design specifications. The scope of this research project is dimensional acceptance of machined parts; specifically, parts machined using numerically controlled (NC, or also CNC for Computer Numerically Controlled) machines. In the design/build/accept cycle, the designer will specify both a nominal value, and an acceptable tolerance. As part of the typical design/build/accept business practice, it is required to verifymore » that the part did meet acceptable values prior to acceptance. Manufacturing cost must include not only raw materials and added labor, but also the cost of ensuring conformance to specifications. Ensuring conformance is a substantial portion of the cost of manufacturing. In this project, the costs of measurements were approximately 50% of the cost of the machined part. In production, cost of measurement would be smaller, but still a substantial proportion of manufacturing cost. The results of this research project will point to a science-based approach to reducing the cost of ensuring conformance to specifications. The approach that we take is to determine, a priori, how well a CNC machine can manufacture a particular geometry from stock. Based on the knowledge of the manufacturing process, we are then able to decide features which need further measurements from features which can be accepted 'as is' from the CNC. By calibration of the machine tool, and establishing a machining accuracy ratio, we can validate the ability of CNC to fabricate to a particular level of tolerance. This will eliminate the costs of checking for conformance for relatively large tolerances.« less

Thermographic Imaging of Defects in Anisotropic Composites

NASA Technical Reports Server (NTRS)

Plotnikov, Y. A.; Winfree, W. P.

2000-01-01

Composite materials are of increasing interest to the aerospace industry as a result of their weight versus performance characteristics. One of the disadvantages of composites is the high cost of fabrication and post inspection with conventional ultrasonic scanning systems. The high cost of inspection is driven by the need for scanning systems which can follow large curve surfaces. Additionally, either large water tanks or water squirters are required to couple the ultrasonics into the part. Thermographic techniques offer significant advantages over conventional ultrasonics by not requiring physical coupling between the part and sensor. The thermographic system can easily inspect large curved surface without requiring a surface following scanner. However, implementation of Thermal Nondestructive Evaluations (TNDE) for flaw detection in composite materials and structures requires determining its limit. Advanced algorithms have been developed to enable locating and sizing defects in carbon fiber reinforced plastic (CFRP). Thermal Tomography is a very promising method for visualizing the size and location of defects in materials such as CFRP. However, further investigations are required to determine its capabilities for inspection of thick composites. In present work we have studied influence of the anisotropy on the reconstructed image of a defect generated by an inversion technique. The composite material is considered as homogeneous with macro properties: thermal conductivity K, specific heat c, and density rho. The simulation process involves two sequential steps: solving the three dimensional transient heat diffusion equation for a sample with a defect, then estimating the defect location and size from the surface spatial and temporal thermal distributions (inverse problem), calculated from the simulations.

Automated Cutting And Drilling Of Composite Parts

NASA Technical Reports Server (NTRS)

Warren, Charles W.

1993-01-01

Proposed automated system precisely cuts and drills large, odd-shaped parts made of composite materials. System conceived for manufacturing lightweight composite parts to replace heavier parts in Space Shuttle. Also useful in making large composite parts for other applications. Includes robot locating part to be machined, positions cutter, and positions drill. Gantry-type robot best suited for task.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Ling; Post, Brian; Kunc, Vlastimil

Additive manufacturing (AM) or 3D printing is well known for producing arbitrary shaped parts without any tooling required, offering a promising alternative to the conventional injection molding method to fabricate near-net-shaped magnets. In order to determine their applicability in the fabrication of Nd-Fe-B bondedmagnets, we compare two 3D printing technologies, namely binder jetting and material extrusion. Some prospects and challenges of these state-of-the-art technologies for large-scale industrial applications will be discussed.

The Development and Status of Earth Science Education: A Comparison of Three Case Studies: Israel, England and Wales and the United States of America. Part I.

ERIC Educational Resources Information Center

Orion, Nir; King, Chris; Krockover, Gerald H.; Adams, Paul E.

1999-01-01

Explores the development and status of Earth Science Education in Israel and England and Wales. Finds that, despite separate traditions for education in the Earth Sciences, there are a surprisingly large number of commonalities between current trends in each of the countries in the study, and each has had difficulty determining what constitutes an…

A simple mercury vapor detector for geochemical prospecting

USGS Publications Warehouse

Vaughn, William W.

1967-01-01

The detector utilizes a large-volume atomic-absorption technique for quantitative determinations of mercury vapor thermally released from crushed rock. A quartz-enclosed noble-metal amalgamative stage, which is temperature controlled and is actuated by a radio-frequency induction heater, selectively traps the mercury and eliminates low-level contamination. As little as 1 part per billion of mercury can be detected in a 1-gram sample in a 1-minute analytical period.

What was the ancestral sex-determining mechanism in amniote vertebrates?

PubMed

Johnson Pokorná, Martina; Kratochvíl, Lukáš

2016-02-01

Amniote vertebrates, the group consisting of mammals and reptiles including birds, possess various mechanisms of sex determination. Under environmental sex determination (ESD), the sex of individuals depends on the environmental conditions occurring during their development and therefore there are no sexual differences present in their genotypes. Alternatively, through the mode of genotypic sex determination (GSD), sex is determined by a sex-specific genotype, i.e. by the combination of sex chromosomes at various stages of differentiation at conception. As well as influencing sex determination, sex-specific parts of genomes may, and often do, develop specific reproductive or ecological roles in their bearers. Accordingly, an individual with a mismatch between phenotypic (gonadal) and genotypic sex, for example an individual sex-reversed by environmental effects, should have a lower fitness due to the lack of specialized, sex-specific parts of their genome. In this case, evolutionary transitions from GSD to ESD should be less likely than transitions in the opposite direction. This prediction contrasts with the view that GSD was the ancestral sex-determining mechanism for amniote vertebrates. Ancestral GSD would require several transitions from GSD to ESD associated with an independent dedifferentiation of sex chromosomes, at least in the ancestors of crocodiles, turtles, and lepidosaurs (tuataras and squamate reptiles). In this review, we argue that the alternative theory postulating ESD as ancestral in amniotes is more parsimonious and is largely concordant with the theoretical expectations and current knowledge of the phylogenetic distribution and homology of sex-determining mechanisms. © 2014 Cambridge Philosophical Society.

New method of processing heat treatment experiments with numerical simulation support

NASA Astrophysics Data System (ADS)

Kik, T.; Moravec, J.; Novakova, I.

2017-08-01

In this work, benefits of combining modern software for numerical simulations of welding processes with laboratory research was described. Proposed new method of processing heat treatment experiments leading to obtaining relevant input data for numerical simulations of heat treatment of large parts was presented. It is now possible, by using experiments on small tested samples, to simulate cooling conditions comparable with cooling of bigger parts. Results from this method of testing makes current boundary conditions during real cooling process more accurate, but also can be used for improvement of software databases and optimization of a computational models. The point is to precise the computation of temperature fields for large scale hardening parts based on new method of temperature dependence determination of the heat transfer coefficient into hardening media for the particular material, defined maximal thickness of processed part and cooling conditions. In the paper we will also present an example of the comparison standard and modified (according to newly suggested methodology) heat transfer coefficient data’s and theirs influence on the simulation results. It shows how even the small changes influence mainly on distribution of temperature, metallurgical phases, hardness and stresses distribution. By this experiment it is also possible to obtain not only input data and data enabling optimization of computational model but at the same time also verification data. The greatest advantage of described method is independence of used cooling media type.

Formation Stellaire Aux Échelles Des Galaxies

NASA Astrophysics Data System (ADS)

Boissier, S.

2012-12-01

Star Formation is at the very core of the evolution of galaxies. From their gas reservoir (filled by infall or fusions), stars form at the "Star Formation Rate" (SFR), with an enormous impact on many aspects of the evolution of galaxies. This HDR presents first the formalism concerning star formation (SFR, IMF), some theoretical suggestions on physical processes that may affect star formation on various galactic scales, and the methods used to determine the SFR from observations. A large part is dedicated to the "Star Formation Laws" (e.g. Schmidt law) on various scales (local, radial, and global law). Finally, the last part concerns the largest scales (evolution of the "cosmic" SFR and effect of the environment).

The Methodology Applied in DPPH, ABTS and Folin-Ciocalteau Assays Has a Large Influence on the Determined Antioxidant Potential.

PubMed

Abramovič, Helena; Grobin, Blaž; Poklar, Nataša; Cigić, Blaž

2017-06-01

Antioxidant potential (AOP) is not only the property of the matrix analyzed but also depends greatly on the methodology used. The chromogenic radicals 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS•+), 2,2-diphenyl-1-picrylhydrazyl (DPPH•) and Folin-Ciocalteu (FC) assay were applied to estimate how the method and the composition of the assay solvent influence the AOP determined for coffee, tea, beer, apple juice and dietary supplements. Large differences between the AOP values depending on the reaction medium were observed, with the highest AOP determined mostly in the FC assay. In reactions with chromogenic radicals several fold higher values of AOP were obtained in buffer pH 7.4 than in water or methanol. The type of assay and solvent composition have similar influences on the reactivity of a particular antioxidant, either pure or as part of a complex matrix. The reaction kinetics of radicals with antioxidants in samples reveals that AOP depends strongly on incubation time, yet differently for each sample analyzed and the assay applied.

Assessment of exposure to manganese in welding operations during the assembly of heavy excavation machinery accessories.

PubMed

Smargiassi, A; Baldwin, M; Savard, S; Kennedy, G; Mergler, D; Zayed, J

2000-10-01

Welder exposure to metals in various industrial sectors is poorly characterized. We had the opportunity to carry out an exploratory study to characterize manganese exposure in welding operations in a recently established Quebec factory that assembled accessories for heavy excavation machinery. Ten workers were sampled for total manganese for at least two consecutive days out of three followed by two consecutive days for respirable manganese (with a size selective sampler with a median cut-off of 4 microns), during a typical week in the summer of 1998. Parts being welded were characterized as large or small. Small parts were those being welded on tables during subassembly. Workers were divided into two groups according to the parts they were welding. Seventy-eight percent of the total manganese exposure levels of welding operations during the assembly of large accessories of heavy excavation machinery exceeded the manganese American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 0.20 mg/m3 (GM 0.24 mg/m3, n = 14) while none exceeded the TLV during the assembly of small pieces (GM 0.06 mg/m3, n = 8). Welding operations during the assembly of large heavy excavation machinery accessories may pose a significant health hazard. Considering the importance of task-related variables affecting exposure among workers, further studies are needed to better characterize exposure determinants of welding operations during the assembly of heavy excavation machinery accessories.

A New Merit Function for Evaluating the Flaw Tolerance of Composite Laminates. Part 2; Arbitrary Size Holes and Center Cracks

NASA Technical Reports Server (NTRS)

Martin, Mikulas M., Jr.; Sumpter, Rod

2000-01-01

In a previous paper, a new merit function for determining the strength performance of flawed composite laminates was presented. This previous analysis was restricted to circular hole flaws that were large enough that failure could be predicted using the laminate stress concentration factor. In this paper, the merit function is expanded to include the flaw cases of an arbitrary size circular hole or center crack. Failure prediction for these cases is determined using the point stress criterion. An example application of the merit function is included for a wide range of graphite/epoxy laminates.

A New Merit Function for Evaluating the Flaw Tolerance of Composite Laminates. Part 2; Arbitrary Size Holes and Center Cracks

NASA Technical Reports Server (NTRS)

Mikulas, Martin M., Jr.; Sumpter, Rod

1997-01-01

In a previous paper, a new merit function for determining the strength performance of flawed composite laminates was presented. This previous analysis was restricted to circular hole flaws that were large enough that failure could be predicted using the laminate stress concentration factor. In this paper, the merit function is expanded to include the flaw cases of an arbitrary size circular hole or a center crack. Failure prediction for these cases is determined using the point stress criterion. An example application of the merit function is included for a wide range of graphite/epoxy laminates.

Quantum dynamics by the constrained adiabatic trajectory method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leclerc, A.; Jolicard, G.; Guerin, S.

2011-03-15

We develop the constrained adiabatic trajectory method (CATM), which allows one to solve the time-dependent Schroedinger equation constraining the dynamics to a single Floquet eigenstate, as if it were adiabatic. This constrained Floquet state (CFS) is determined from the Hamiltonian modified by an artificial time-dependent absorbing potential whose forms are derived according to the initial conditions. The main advantage of this technique for practical implementation is that the CFS is easy to determine even for large systems since its corresponding eigenvalue is well isolated from the others through its imaginary part. The properties and limitations of the CATM are exploredmore » through simple examples.« less

The first science result with the JENSA gas-jet target: Confirmation and study of a strong subthreshold F 18 ( p , α ) O 15 resonance

DOE PAGES

Bardayan, D. W.; Chipps, K. A.; Ahn, S.; ...

2015-11-28

The astrophysical 18F( p,α) 15O rate determines, in large part, the extent to which the observable radioisotope 18F is produced in novae. This rate, however, has been extremely uncertain owing to the unknown properties of a strong subthreshold resonance and its possible interference with higher-lying resonances. In addition, the new Jet Experiments in Nuclear Structure and Astrophysics (JENSA) gas-jet target has been used for the first time to determine the spin of this important resonance and significantly reduce uncertainties in the 18F( p,α) 15O rate.

A pore-pressure diffusion model for estimating landslide-inducing rainfall

USGS Publications Warehouse

Reid, M.E.

1994-01-01

Many types of landslide movement are induced by large rainstorms, and empirical rainfall intensity/duration thresholds for initiating movement have been determined for various parts of the world. In this paper, I present a simple pressure diffusion model that provides a physically based hydrologic link between rainfall intensity/duration at the ground surface and destabilizing pore-water pressures at depth. The model approximates rainfall infiltration as a sinusoidally varying flux over time and uses physical parameters that can be determined independently. Using a comprehensive data set from an intensively monitored landslide, I demonstrate that the model is capable of distinguishing movement-inducing rainstorms. -Author

The first science result with the JENSA gas-jet target: Confirmation and study of a strong subthreshold F 18 ( p , α ) O 15 resonance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bardayan, D. W.; Chipps, K. A.; Ahn, S.

The astrophysical 18F( p,α) 15O rate determines, in large part, the extent to which the observable radioisotope 18F is produced in novae. This rate, however, has been extremely uncertain owing to the unknown properties of a strong subthreshold resonance and its possible interference with higher-lying resonances. In addition, the new Jet Experiments in Nuclear Structure and Astrophysics (JENSA) gas-jet target has been used for the first time to determine the spin of this important resonance and significantly reduce uncertainties in the 18F( p,α) 15O rate.

Anchorage failure of young trees in sandy soils is prevented by a rigid central part of the root system with various designs

PubMed Central

Danquechin Dorval, Antoine; Meredieu, Céline; Danjon, Frédéric

2016-01-01

Background and Aims Storms can cause huge damage to European forests. Even pole-stage trees with 80-cm rooting depth can topple. Therefore, good anchorage is needed for trees to survive and grow up from an early age. We hypothesized that root architecture is a predominant factor determining anchorage failure caused by strong winds. Methods We sampled 48 seeded or planted Pinus pinaster trees of similar aerial size from four stands damaged by a major storm 3 years before. The trees were gathered into three classes: undamaged, leaning and heavily toppled. After uprooting and 3D digitizing of their full root architectures, we computed the mechanical characteristics of the main components of the root system from our morphological measurements. Key Results Variability in root architecture was quite large. A large main taproot, either short and thick or long and thin, and guyed by a large volume of deep roots, was the major component that prevented stem leaning. Greater shallow root flexural stiffness mainly at the end of the zone of rapid taper on the windward side also prevented leaning. Toppling in less than 90-cm-deep soil was avoided in trees with a stocky taproots or with a very big leeward shallow root. Toppled trees also had a lower relative root biomass – stump excluded – than straight trees. Conclusions It was mainly the flexural stiffness of the central part of the root system that secured anchorage, preventing a weak displacement of the stump. The distal part of the longest taproot and attached deep roots may be the only parts of the root system contributing to anchorage through their maximum tensile load. Several designs provided good anchorage, depending partly on available soil depth. Pole-stage trees are in-between the juvenile phase when they fail by toppling and the mature phase when they fail by uprooting. PMID:27456136

Semi-Empirical Modeling of SLD Physics

NASA Technical Reports Server (NTRS)

Wright, William B.; Potapczuk, Mark G.

2004-01-01

The effects of supercooled large droplets (SLD) in icing have been an area of much interest in recent years. As part of this effort, the assumptions used for ice accretion software have been reviewed. A literature search was performed to determine advances from other areas of research that could be readily incorporated. Experimental data in the SLD regime was also analyzed. A semi-empirical computational model is presented which incorporates first order physical effects of large droplet phenomena into icing software. This model has been added to the LEWICE software. Comparisons are then made to SLD experimental data that has been collected to date. Results will be presented for the comparison of water collection efficiency, ice shape and ice mass.

The development of a capability for aerodynamic testing of large-scale wing sections in a simulated natural rain environment

NASA Technical Reports Server (NTRS)

Bezos, Gaudy M.; Cambell, Bryan A.; Melson, W. Edward

1989-01-01

A research technique to obtain large-scale aerodynamic data in a simulated natural rain environment has been developed. A 10-ft chord NACA 64-210 wing section wing section equipped with leading-edge and trailing-edge high-lift devices was tested as part of a program to determine the effect of highly-concentrated, short-duration rainfall on airplane performance. Preliminary dry aerodynamic data are presented for the high-lift configuration at a velocity of 100 knots and an angle of attack of 18 deg. Also, data are presented on rainfield uniformity and rainfall concentration intensity levels obtained during the calibration of the rain simulation system.

Battle on the Bookshelves: History, Desert Storm, and the United States Armed Forces

DTIC Science & Technology

2004-06-17

impacted on the outcome of the war, ranging from superior American technology to flagging Iraqi morale, each of the armed services is free to claim...though decidedly more subtle, could 5 have an equally large impact at the strategic level. For instance, if a service succeeds in overstating its...official accounts of a campaign. Therefore, as part o this work, it is necessary to determine the impact of organizational culture on the observed

Arbitrary Budget Cuts and the U.S. National Security Posture

DTIC Science & Technology

1990-12-01

consensus between both branches of government on exactly what the future U.S. defense stategy should be, a dilemma made more difficult due to their...international trade issues and the status of their balance of payments. They will monitor the value of foreign currencies and markets around the world...8217 economy will certainly play a large part in the delicate balance of the current world market , and its economic well-being will further determine the

PROGRAM ASTEC (ADVANCED SOLAR TURBO ELECTRIC CONCEPT). PART IV. SOLAR COLLECTOR DEVELOPMENT SUPPORT TASKS. VOL. VI. DEVELOPMENT OF ANALYTICAL TECHNIQUES TO PREDICT THE STRUCTURAL BEHAVIOR OF PETAL-TYPE SOLAR COLLECTORS.

DTIC Science & Technology

The design of large petal-type paraboloidal solar collectors for the ASTEC Program requires a capability for determining the distortion and stress...analysis of a parabolic curved beam is given along with a numerical solution and digital program. The dynamic response of the ASTEC flight-test vehicle is discussed on the basis of modal analysis.

Uranium content of ground and surface waters in western Kansas, eastern Colorado, and the Oklahoma Panhande

USGS Publications Warehouse

Landis, E.R.

1956-01-01

and in some parts of the report area, such as the Cimarron River area of westernmost Oklahoma and northeastern New Mexico, and the Rule Creek area in Bent and Las Animas Counties, Colo. , most, or all, of the water samples collected contain relatively large amounts of uranium. Further exploration to determine the source of the uranium in the water from these rock units and areas may be worthwhile.

A Blast of Cool Air

NASA Technical Reports Server (NTRS)

2000-01-01

Unable to solve their engineering problem with a rotor in their Orbital Vane product, DynEco Corporation turned to Kennedy Space Center for help. KSC engineers determined that the compressor rotor was causing a large concentration of stress, which led to cracking and instant rotor failure. NASA redesigned the lubrication system, which allowed the company to move forward with its compressor that has no rubbing parts. The Orbital Vane is a refrigerant compressor suitable for mobile air conditioning and refrigeration.

The impact on floats or hulls during landing as affected by bottom width

NASA Technical Reports Server (NTRS)

Mewes, E

1936-01-01

For floats and hulls having V bottoms the impact force does not necessarily increase with increasing width. Therefore, the weight of the float landing gear, side walls, and other parts, and of the fuselage construction need not be increased with increasing bottom width, but the weight of the bottom construction itself, on the other hand, does not increase with increase in bottom width and is largely determined by the type of construction.

Hotspot Patterns: The Formal Definition and Automatic Detection of Architecture Smells

DTIC Science & Technology

2015-01-15

serious question for a project manager or architect: how to determine which parts of the code base should be given higher priority for maintenance and...services framework; Hadoop8 is a tool for distributed processing of large data sets; HBase9 is the Hadoop database; Ivy10 is a dependency management tool...answer this question more rigorously, we conducted Pearson Correlation Analysis to test the dependency between the number of issues a file involves

An Analysis of the Best Available Unmanned Ground Vehicle in the Current Market with Respect to the Requirements of the Turkish Ministry of National Defense

DTIC Science & Technology

2011-12-01

Special Weapons and Tactics SWORDS Special Weapons Observation Remote Reconnaissance Direct Action System TAF Turkish Armed Forces tEODor...especially concentrated in the southeastern part of Turkey where the Turkish Armed Forces ( TAF ) are fighting against terrorists determinedly and continuously...Systems (MDS) to strengthen the TAF and to modernize its current systems. Today, many countries are making large investments to strengthen their

Hydrogeology of glacial deposits in a preglacial bedrock valley, Waukesha County, Wisconsin

USGS Publications Warehouse

Batten, W.G.; Conlon, T.D.

1993-01-01

Results of a 6.5-hour aquifer test indicate that the silty sand and gravel deposits have an average transmissivity of about 140 feet squared per day and an average storage coefficient of about 1.2x10"3 at one location. The horizontal hydraulic conductivity of these deposits averages about 4 feet per day. Analysis of drawdown indicates that these deposits are part of a leaky confined-aquifer system and that some water is derived from storage in an overlying clay layer. The transmissivity value determined from this aquifer test and a lack of clean sand and gravel encountered in other test holes indicate that glacial deposits at these sites may not yield enough water for a large municipal water supply. Sand and gravel deposits, capable of development as a municipal supply, may be present in the southern part of the study area. However, additional test holes are needed to determine whether adequate sand and gravel deposits underlie this area.

Improvement of ion thruster design

NASA Technical Reports Server (NTRS)

Carpenter, R. T.

1986-01-01

Two types of measurements were performed on ion thrustors equipped with SmCo magnets in either ring cusp or line cusp arrangements. Langmuir probes were used to measure plasma potential, electron density, and electron temperture in all regions inside the thruster. Loss fluxes to various surfaces were determined by measuring the currents to foils attached to or imbedded in the surface. Data were obtained for several sets of discharge voltages and currents. The loss currents were determined from current vs voltage characteristics observed on a transistor curve tracer oscilloscope. Both ion and electron currents were measured to all parts of the walls and to all parts of the cathode assembly using collecting plates. These measurement were also made for various parameter sets. In line cusp configuration the plasma density is essentially as predicted by existing calculations. In the ring cusp arrangement the interior of the plasma contains an inhomogeneous and relatively large magnetic field so the geometry is decidely two-dimensional and the models of Self (1967) and of Kino and Sham (1966) do not agree.

Pilot Perception of Electronic Flight Bags at Part 121 Air Carriers

NASA Astrophysics Data System (ADS)

Lytle, Donley

Electronic Flight Bags (EFBs) have been approved for use by pilots in flight operations at many Part 121 air carriers in the United States since 2010. As an automated device replacing paper in the cockpit, there are many human factor issues that relate to operation of the EFB. EFBs have been cited in accidents and incidents worldwide in large, transport category aircraft. While the EFB was not cited as the main cause of the accident/incident, it has been listed as a contributing factor. This study looks at pilot perception related to the safety aspect of the EFB in flight operations at Part 121 carriers in the United States. It surveys pilots that utilize the device in daily, routine flight operations to determine their perception of the EFB. The study is followed with a survey of a small group of pilots to help explain the results and any correlation between the variables.

Delayed Graft Function in Living-Donor Kidney Transplant: A Middle Eastern Perspective.

PubMed

Al Otaibi, Torki; Ahmadpoor, Pedram; Allawi, Ali Abdulmajid Dyab; Habhab, Wael Taher; Khatami, Mohammad Reza; Nafar, Mohsen; Glotz, Denis

2016-02-01

With an increased incidence of living-donor kidney transplants, in response to increasing unmet needs for renal transplant, a clear understanding of determinants of posttransplant outcomes is essential. The importance of delayed graft function in deceased-donor kidney transplant is now part of conventional medical wisdom, due to the large amount of evidence focused on this aspect. However, the same is not true for living-donor kidney transplant, partly due to lack of evidence on this crucial clinical question and partly due to lack of awareness about this issue. The current review aims to highlight the importance of delayed graft function as a crucial determinant of outcomes in living-donor kidney transplant. An exhaustive search of online medical databases was performed with appropriate search criteria to collect evidence about delayed graft function after living-donor kidney transplant, with a special focus on studies from the Middle East. Data on incidence, impact, risk factors, and possible prevention modalities of delayed graft function in patients undergoing living-donor kidney transplant are presented. A key finding of this review is that contemporary incidence rates reported from the Middle East are comparatively higher than those reported from outside the region. Although in absolute terms the incidence is lower than deceased donor kidney transplant, the effects of delayed graft function on graft rejection and graft and patient survival are sufficiently large to warrant the formulation of specific treatment protocols. Key to formulating prevention and treatment strategies is identifying discrete risk factors for delayed graft function. Although this evidence is scant, an overview has been provided. Further studies examining different aspects of delayed graft function incidence after living-donor kidney transplant are urgently needed to address a so far little known clinical question.

Thermoregulatory behavior of bluegill, Lepomis macrochirus from a thermally stressed ecosystem. [Lepomis macrochirus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, R.U. Jr.

1984-12-01

Bluegills, Lepomis macrochirus were used as a representative aquatic ectotherm to determine the importance of behavior in thermoregulation of fish inhabiting a thermally stressed ecosystem. In the first part of the study, the mean final temperature preferenda for small bluegills from the heated and normothermic sites (25.2/sup 0/C vs 25.0/sup 0/C) were not significantly different. In the second part of the study, the acute preferred temperatures of large L. macrochirus (anti X = 26.3/sup 0/C) showed a statistically significant difference from that of small bluegills (anti X = 25.2/sup 0/C). There was no significant difference in the acute preferred temperaturesmore » for bluegill from the heated and normothermic sites. In the last phase of the study L. macrochirus from both a thermally stressed and normothermic site were tested for upper avoidance temperature in the absence of and in the presence of two sizes of predators (Micropterus salmoides, largemouth bass). In the absence of a predator the small bluegill had a mean upper avoidance temperature of 30.0/sup 0/C as compared to 29.8/sup 0/C for the large bluegills. In the presence of a small and large predator the small bluegills had a mean upper avoidance temperature of 34.0/sup 0/C and 33.9/sup 0/C respectively, while the large bluegills had mean upper avoidance temperatures of 33.8/sup 0/C and 33.1/sup 0/C. In the presence of a predator bluegill upper avoidance temperatures were significantly higher, however, predator size did not influence this relationship. During the determinations of final temperature preferendum, acute preferred temperature, and upper avoidance temperature, the fish from the heated site always exhibited less variability in temperature measurements than those from the control site. 41 refs., 9 figs., 10 tabs.« less

Analysis on the restriction factors of the green building scale promotion based on DEMATEL

NASA Astrophysics Data System (ADS)

Wenxia, Hong; Zhenyao, Jiang; Zhao, Yang

2017-03-01

In order to promote the large-scale development of the green building in our country, DEMATEL method was used to classify influence factors of green building development into three parts, including green building market, green technology and macro economy. Through the DEMATEL model, the interaction mechanism of each part was analyzed. The mutual influence degree of each barrier factor that affects the green building promotion was quantitatively analysed and key factors for the development of green building in China were also finally determined. In addition, some implementation strategies of promoting green building scale development in our country were put forward. This research will show important reference value and practical value for making policies of the green building promotion.

Preliminary Geophysical Investigations of the Ship Rock Diatreme, Navajo Nation, New Mexico

NASA Astrophysics Data System (ADS)

Gruen, E. M.; McCarthy, L.; Namingha, G.; Bank, C.; Noblett, J.; Semken, S.

2003-12-01

Magnetic and gravity data were collected at the Ship Rock minette neck and dikes, part of the Navajo volcanic field in the central Colorado Plateau, to investigate their subsurface structure. The deep root system of Ship Rock, an exhumed Oligocene maar-diatreme complex, has not been resolved. The diatreme is largely composed of minette tuff-breccia with a large wallrock fraction, whereas the dikes are composed of hypabyssal minette. The country rock is the Upper Cretaceous Mancos Shale. Density and magnetic contrasts between the igneous rock and surrounding shale suggest that the buried structure of Ship Rock can be imaged. Preliminary geophysical investigations were carried out in order to test this hypothesis. We collected magnetic and gravitational data along four lines selected to transect the major south and northeast dikes and to partly encircle the diatreme. Modeling differently sized, oriented and shaped intrusions, we created theoretical Free Air anomaly curves to try to match the two clearest anomalies. Modeling necessitates (i) that the major north-south dike dips west and (ii) the presence of a high-density, deep body near the diatreme. The Free Air anomaly curves show that smaller dikes might not be detected from gravity data; however, they are necessary to determine the presence of large, dense bodies. Although not modeled, the magnetics curves show that smaller dikes can easily be detected. Our study results are promising, and we plan a more thorough investigation in the future which will produce a magnetic map to determine if further buried dikes exist in the vicinity, and measure gravity along additional profiles to better constrain the location of the dense body at depth.

Determination of Radiographic Healing: An Assessment of Consistency Using RUST and Modified RUST in Metadiaphyseal Fractures.

PubMed

Litrenta, Jody; Tornetta, Paul; Mehta, Samir; Jones, Clifford; OʼToole, Robert V; Bhandari, Mohit; Kottmeier, Stephen; Ostrum, Robert; Egol, Kenneth; Ricci, William; Schemitsch, Emil; Horwitz, Daniel

2015-11-01

To determine the reliability of the Radiographic Union Scale for Tibia (RUST) score and a new modified RUST score in quantifying healing and to define a value for radiographic union in a large series of metadiaphyseal fractures treated with plates or intramedullary nails. Healing was evaluated using 2 methods: (1) evaluation of interrater agreement in a series of radiographs and (2) analysis of prospectively gathered data from 2 previous large multicenter trials to define thresholds for radiographic union. Part 1: 12 orthopedic trauma surgeons evaluated a series of radiographs of 27 distal femur fractures treated with either plate or retrograde nail fixation at various stages of healing in random order using a modified RUST score. For each radiographic set, the reviewer indicated if the fracture was radiographically healed. Part 2: The radiographic results of 2 multicenter randomized trials comparing plate versus nail fixation of 81 distal femur and 46 proximal tibia fractures were reviewed. Orthopaedic surgeons at 24 trauma centers scored radiographs at 3, 6, and 12 months postoperatively using the modified RUST score above. Additionally, investigators indicated if the fracture was healed or not healed. The intraclass correlation coefficient (ICC) with 95% confidence intervals was determined for each cortex, the standard and modified RUST score, and the assignment of union for part 1 data. The RUST and modified RUST that defined "union" were determined for both parts of the study. ICC: The modified RUST score demonstrated slightly higher ICCs than the standard RUST (0.68 vs. 0.63). Nails had substantial agreement, whereas plates had moderate agreement using both modified and standard RUST (0.74 and 0.67 vs. 0.59 and 0.53). The average standard and modified RUST at union among all fractures was 8.5 and 11.4. Nails had higher standard and modified RUST scores than plates at union. The ICC for union was 0.53 (nails: 0.58; plates: 0.51), which indicates moderate agreement. However, the majority of reviewers assigned union for a standard RUST of 9 and a modified RUST of 11, and >90% considered a score of 10 on the RUST and 13 on the modified RUST united. The ICC for the modified RUST is slightly higher than the standard RUST in metadiaphyseal fractures and had substantial agreement. The ICC for the assessment of union was moderate agreement; however, definite union would be 10 and 13 with over 90% of reviewers assigning union. These are the first data-driven estimates of radiographic union for these scores.

Zircons reveal magma fluxes in the Earth's crust.

PubMed

Caricchi, Luca; Simpson, Guy; Schaltegger, Urs

2014-07-24

Magma fluxes regulate the planetary thermal budget, the growth of continents and the frequency and magnitude of volcanic eruptions, and play a part in the genesis and size of magmatic ore deposits. However, because a large fraction of the magma produced on the Earth does not erupt at the surface, determinations of magma fluxes are rare and this compromises our ability to establish a link between global heat transfer and large-scale geological processes. Here we show that age distributions of zircons, a mineral often present in crustal magmatic rocks, in combination with thermal modelling, provide an accurate means of retrieving magma fluxes. The characteristics of zircon age populations vary significantly and systematically as a function of the flux and total volume of magma accumulated in the Earth's crust. Our approach produces results that are consistent with independent determinations of magma fluxes and volumes of magmatic systems. Analysis of existing age population data sets using our method suggests that porphyry-type deposits, plutons and large eruptions each require magma input over different timescales at different characteristic average fluxes. We anticipate that more extensive and complete magma flux data sets will serve to clarify the control that the global heat flux exerts on the frequency of geological events such as volcanic eruptions, and to determine the main factors controlling the distribution of resources on our planet.

Redefining the genetics of Murine Gammaherpesvirus 68 via transcriptome-based annotation

PubMed Central

Johnson, L. Steven; Willert, Erin K.; Virgin, Herbert W.

2010-01-01

Summary Viral genetic studies often focus on large open reading frames (ORFs) identified during genome annotation (ORF-based annotation). Here we provide a tool and software set for defining gene expression by murine gammaherpesvirus 68 (γHV68) nucleotide-by-nucleotide across the 119,450 basepair (bp) genome. These tools allowed us to determine that viral RNA expression was significantly more complex than predicted from ORF-based annotation, including over 73,000 nucleotides of unexpected transcription within 30 expressed genomic regions (EGRs). Approximately 90% of this RNA expression was antisense to genomic regions containing known large ORFs. We verified the existence of novel transcripts in three EGRs using standard methods to validate the approach and determined which parts of the transcriptome depend on protein or viral DNA synthesis. This redefines the genetic map of γHV68, indicates that herpesviruses contain significantly more genetic complexity than predicted from ORF-based genome annotations, and provides new tools and approaches for viral genetic studies. PMID:20542255

Zircon Age Distributions Provide Magma Fluxes in the Earth's Crust

NASA Astrophysics Data System (ADS)

Caricchi, L.; Simpson, G.; Schaltegger, U.

2014-12-01

Magma fluxes control the growth of continents, the frequency and magnitude of volcanic eruptions and are important for the genesis of magmatic ore deposits. A significant part of the magma produced in the Earth's mantle solidifies at depth and this limits our capability of determining magma fluxes, which, in turn, compromises our ability to establish a link between global heat transfer and large-scale geological processes. Using thermal modelling in combination with high precision zircon dating we show that populations of zircon ages provide an accurate mean to retrieve magma fluxes. The characteristics of zircon age populations vary significantly and systematically as function of the flux and total volume of magma accumulated at depth. This new approach provides results that are identical to independent determinations of magma fluxes and volumes of magmatic systems. The analysis of existing age population datasets by our method highlights that porphyry-type deposits, plutons and large eruptions each require magma input over different timescales at characteristic average fluxes.

A Method for Assessing the Accuracy of a Photogrammetry System for Precision Deployable Structures

NASA Technical Reports Server (NTRS)

Moore, Ashley

2005-01-01

The measurement techniques used to validate analytical models of large deployable structures are an integral Part of the technology development process and must be precise and accurate. Photogrammetry and videogrammetry are viable, accurate, and unobtrusive methods for measuring such large Structures. Photogrammetry uses Software to determine the three-dimensional position of a target using camera images. Videogrammetry is based on the same principle, except a series of timed images are analyzed. This work addresses the accuracy of a digital photogrammetry system used for measurement of large, deployable space structures at JPL. First, photogrammetry tests are performed on a precision space truss test article, and the images are processed using Photomodeler software. The accuracy of the Photomodeler results is determined through, comparison with measurements of the test article taken by an external testing group using the VSTARS photogrammetry system. These two measurements are then compared with Australis photogrammetry software that simulates a measurement test to predict its accuracy. The software is then used to study how particular factors, such as camera resolution and placement, affect the system accuracy to help design the setup for the videogrammetry system that will offer the highest level of accuracy for measurement of deploying structures.

A Fast Evaluation Method for Energy Building Consumption Based on the Design of Experiments

NASA Astrophysics Data System (ADS)

Belahya, Hocine; Boubekri, Abdelghani; Kriker, Abdelouahed

2017-08-01

Building sector is one of the effective consumer energy by 42% in Algeria. The need for energy has continued to grow, in inordinate way, due to lack of legislation on energy performance in this large consumer sector. Another reason is the simultaneous change of users’ requirements to maintain their comfort, especially summer in dry lands and parts of southern Algeria, where the town of Ouargla presents a typical example which leads to a large amount of electricity consumption through the use of air conditioning. In order to achieve a high performance envelope of the building, an optimization of major parameters building envelope is required, using design of experiments (DOE), can determine the most effective parameters and eliminate the less importance. The study building is often complex and time consuming due to the large number of parameters to consider. This study focuses on reducing the computing time and determines the major parameters of building energy consumption, such as area of building, factor shape, orientation, ration walls to windows …etc to make some proposal models in order to minimize the seasonal energy consumption due to air conditioning needs.

Climate variability rather than overstocking causes recent large scale cover changes of Tibetan pastures

PubMed Central

Lehnert, L. W.; Wesche, K.; Trachte, K.; Reudenbach, C.; Bendix, J.

2016-01-01

The Tibetan Plateau (TP) is a globally important “water tower” that provides water for nearly 40% of the world’s population. This supply function is claimed to be threatened by pasture degradation on the TP and the associated loss of water regulation functions. However, neither potential large scale degradation changes nor their drivers are known. Here, we analyse trends in a high-resolution dataset of grassland cover to determine the interactions among vegetation dynamics, climate change and human impacts on the TP. The results reveal that vegetation changes have regionally different triggers: While the vegetation cover has increased since the year 2000 in the north-eastern part of the TP due to an increase in precipitation, it has declined in the central and western parts of the TP due to rising air temperature and declining precipitation. Increasing livestock numbers as a result of land use changes exacerbated the negative trends but were not their exclusive driver. Thus, we conclude that climate variability instead of overgrazing has been the primary cause for large scale vegetation cover changes on the TP since the new millennium. Since areas of positive and negative changes are almost equal in extent, pasture degradation is not generally proceeding. PMID:27073126

Climate variability rather than overstocking causes recent large scale cover changes of Tibetan pastures

NASA Astrophysics Data System (ADS)

Lehnert, L. W.; Wesche, K.; Trachte, K.; Reudenbach, C.; Bendix, J.

2016-04-01

The Tibetan Plateau (TP) is a globally important “water tower” that provides water for nearly 40% of the world’s population. This supply function is claimed to be threatened by pasture degradation on the TP and the associated loss of water regulation functions. However, neither potential large scale degradation changes nor their drivers are known. Here, we analyse trends in a high-resolution dataset of grassland cover to determine the interactions among vegetation dynamics, climate change and human impacts on the TP. The results reveal that vegetation changes have regionally different triggers: While the vegetation cover has increased since the year 2000 in the north-eastern part of the TP due to an increase in precipitation, it has declined in the central and western parts of the TP due to rising air temperature and declining precipitation. Increasing livestock numbers as a result of land use changes exacerbated the negative trends but were not their exclusive driver. Thus, we conclude that climate variability instead of overgrazing has been the primary cause for large scale vegetation cover changes on the TP since the new millennium. Since areas of positive and negative changes are almost equal in extent, pasture degradation is not generally proceeding.

Distributed Large Data-Object Environments: End-to-End Performance Analysis of High Speed Distributed Storage Systems in Wide Area ATM Networks

NASA Technical Reports Server (NTRS)

Johnston, William; Tierney, Brian; Lee, Jason; Hoo, Gary; Thompson, Mary

1996-01-01

We have developed and deployed a distributed-parallel storage system (DPSS) in several high speed asynchronous transfer mode (ATM) wide area networks (WAN) testbeds to support several different types of data-intensive applications. Architecturally, the DPSS is a network striped disk array, but is fairly unique in that its implementation allows applications complete freedom to determine optimal data layout, replication and/or coding redundancy strategy, security policy, and dynamic reconfiguration. In conjunction with the DPSS, we have developed a 'top-to-bottom, end-to-end' performance monitoring and analysis methodology that has allowed us to characterize all aspects of the DPSS operating in high speed ATM networks. In particular, we have run a variety of performance monitoring experiments involving the DPSS in the MAGIC testbed, which is a large scale, high speed, ATM network and we describe our experience using the monitoring methodology to identify and correct problems that limit the performance of high speed distributed applications. Finally, the DPSS is part of an overall architecture for using high speed, WAN's for enabling the routine, location independent use of large data-objects. Since this is part of the motivation for a distributed storage system, we describe this architecture.

The demand for ambulatory mental health services from specialty providers.

PubMed Central

Horgan, C M

1986-01-01

A two-part model is used to examine the demand for ambulatory mental health services in the specialty sector. In the first equation, the probability of having a mental health visit is estimated. In the second part of the model, variations in levels of use expressed in terms of visits and expenditures are examined in turn, with each of these equations conditional on positive utilization of mental health services. In the second part of the model, users are additionally grouped into those with and without out-of-pocket payment for services. This specification accounts for special characteristics regarding the utilization of ambulatory mental health services: (1) a large part of the population does not use these services; (2) of those who use services, the distribution of use is highly skewed; and (3) a large number of users have zero out-of-pocket expenditures. Cost-sharing does indeed matter in the demand for ambulatory mental health services from specialty providers; however, the decision to use mental health services is affected by the level of cost-sharing to a lesser degree than is the decision regarding the level of use of services. The results also show that price is only one of several important factors in determining the demand for services. The lack of significance of family income and of being female is notable. Evidence is presented for the existence of bandwagon effects. The importance of Medicaid in the probability of use equations is noted. PMID:3721874

Sequential Determination of U and Th Decay Series in Santana Cave, Southwest Brazil

NASA Astrophysics Data System (ADS)

Silva, P. S. C.; Damatto, S. R.; Mazzilli, B. P.

2008-08-01

Parque Estadual Turístico do Alto Ribeira (PETAR) is located in the South-western part of São Paulo State, in the Ribeira Valley. In this national state park a large number of caves are found, which are among the most visited of the country. These caves, located in a karstic zone, are characterized by the presence of carbonaceous rocks frequently fractured and collapsed. Although, carbonates (dolomites and calcitic rocks) usually have low U content, this element can be found in the structure of the surrounding rocks. This paper aims to determine 238U, 234U, 226Ra and 210Pb concentration in samples of rock, soil, river water and sediment, in Santana cave. The radionuclide 238U was determined by alpha spectrometry using a surface barrier detector. 226Ra and 210Pb were determined by measuring the gross alpha and beta activity on a gas flow proportional counter.

Efficiency and economics of large scale hydrogen liquefaction. [for future generation aircraft requirements

NASA Technical Reports Server (NTRS)

Baker, C. R.

1975-01-01

Liquid hydrogen is being considered as a substitute for conventional hydrocarbon-based fuels for future generations of commercial jet aircraft. Its acceptance will depend, in part, upon the technology and cost of liquefaction. The process and economic requirements for providing a sufficient quantity of liquid hydrogen to service a major airport are described. The design is supported by thermodynamic studies which determine the effect of process arrangement and operating parameters on the process efficiency and work of liquefaction.

Refurbishment of SRB aluminum components by walnut hull blast removal of protective coatings

NASA Technical Reports Server (NTRS)

Colberg, W. R.; Gordon, G. H.; Jackson, C. H.

1982-01-01

A test program was conducted to develop, optimize, and scale up an abrasive blasting procedure was developed for refurbishment of specific SRB components: aft skirt, forward skirt, frustrum, and painted piece parts. Test specimens utilizing 2219 T87 aluminum substrate of varying thicknesses were prepared and blasted at progressively increasing pressures with selected abrasives. Specimens were analyzed for material response. The optimum blasting parameters were determined on panel specimens and verified on a large cylindrical integrated test bed.

Additive manufacturing of near-net-shape bonded magnets: Prospects and challenges

DOE PAGES

Li, Ling; Post, Brian; Kunc, Vlastimil; ...

2017-01-03

Additive manufacturing (AM) or 3D printing is well known for producing arbitrary shaped parts without any tooling required, offering a promising alternative to the conventional injection molding method to fabricate near-net-shaped magnets. In order to determine their applicability in the fabrication of Nd-Fe-B bondedmagnets, we compare two 3D printing technologies, namely binder jetting and material extrusion. Some prospects and challenges of these state-of-the-art technologies for large-scale industrial applications will be discussed.

Application of satellite data for snow mapping in Norway

NASA Technical Reports Server (NTRS)

Odegaard, H. A.; Andersen, T.; Ostrem, G. (Principal Investigator)

1980-01-01

The author has identified the following significant results. A close quantitative relationship was found between snow covered areas and subsequent runoff for different parts of the country despite climate differences. Digital LANDSAT data can be used for areas down to approximately 10 sq km to 20 sq km for accurate measurement of snow cover extent. On large watersheds (more than 500 sq km), digital NOAA/TIROS imagery can be used for snow mapping if the area/runoff relationship is determined by using observations from previous years.

Survey-Guided Development: Data Based Organizational Change

DTIC Science & Technology

1975-06-01

are largely environmentally determined, these experiences ":npact," and as they do so, move from the II 28 more existential surface level to the more...8217 personal values with those humanistic values which he believes are held by top managers today--form the major basis, in Bennis’ view, for the change...as "society." If they are, it is because we adhere to a set of humanistic values and define society’s "work" at least in part in these terms. It is

Personal identification by eyes.

PubMed

Marinović, Dunja; Njirić, Sanja; Coklo, Miran; Muzić, Vedrana

2011-09-01

Identification of persons through the eyes is in the field of biometrical science. Many security systems are based on biometric methods of personal identification, to determine whether a person is presenting itself truly. The human eye contains an extremely large number of individual characteristics that make it particularly suitable for the process of identifying a person. Today, the eye is considered to be one of the most reliable body parts for human identification. Systems using iris recognition are among the most secure biometric systems.

Manned Mars mission crew factors

NASA Technical Reports Server (NTRS)

Santy, Patricia A.

1986-01-01

Crew factors include a wide range of concerns relating to the human system and its role in a Mars mission. There are two important areas which will play a large part in determining the crew for a Mars mission. The first relates to the goals and priorities determined for such a vast endeavor. The second is the design of the vehicle for the journey. The human system cannot be separated from the other systems in that vehicle. In fact it will be the human system which drives the development of many of the technical breakthroughs necessary to make a Mars mission successful. As much as possible, the engineering systems must adapt to the needs of the human system and its individual components.

Dust destruction and thermal inhomogeneities in the Orion Nebula. Results of HH 202.

NASA Astrophysics Data System (ADS)

Espíritu, J.; Peimbert, A.; Delgado-Inglada, G.; Ruiz, M. T.

2017-11-01

We present a long-slit spectroscopic analysis of Herbig-Haro 202 and the surrounding gas of the Orion Nebula using data from the Very Large Telescope. We determined the spatial variation of its physical conditions and chemical abundances. Special attention was paid to the iron (Fe) and oxygen (O) abundances, which show a peak at the brightest part of HH 202, allowing us to estimate that 57% of the dust is the destroyed; we also calculate the amount of depletion of oxygen in dust grains. Finally we show that O abundances determined from collisionally excited lines and recombination lines are irreconcilable at the center of the shock unless thermal inhomogeneities are considered.

Advanced composites structural concepts and materials technologies for primary aircraft structures: Design/manufacturing concept assessment

NASA Technical Reports Server (NTRS)

Chu, Robert L.; Bayha, Tom D.; Davis, HU; Ingram, J. ED; Shukla, Jay G.

1992-01-01

Composite Wing and Fuselage Structural Design/Manufacturing Concepts have been developed and evaluated. Trade studies were performed to determine how well the concepts satisfy the program goals of 25 percent cost savings, 40 percent weight savings with aircraft resizing, and 50 percent part count reduction as compared to the aluminum Lockheed L-1011 baseline. The concepts developed using emerging technologies such as large scale resin transfer molding (RTM), automatic tow placed (ATP), braiding, out-of-autoclave and automated manufacturing processes for both thermoset and thermoplastic materials were evaluated for possible application in the design concepts. Trade studies were used to determine which concepts carry into the detailed design development subtask.

Mycobacterium tuberculosis population structure and molecular epidemiological analysis in Sucre municipality, Miranda state, Venezuela.

PubMed

Patiño, Margareth A; Abadía, Edgar; Solalba Gómez; Maes, Mailis; Muñoz, Mariana; Gómez, Daniela; Guzmán, Patricia; Méndez, María Victoria; Ramirez, Carmen; Mercedes, España; de Waard, Jacobus; Takiff, Howard

2014-12-01

Sucre municipality is a large, densely populated marginal area in the eastern part of Caracas, Venezuela that consistently has more cases of tuberculosis than other municipalities in the country. To identify the neighborhoods in the municipality with the highest prevalence of tuberculosis, and determine whether the Mycobacterium tuberculosis strain distribution in this municipality is different from that previously found in the western part of Caracas and the rest of Venezuela, we collected data on all tuberculosis cases in the municipality diagnosed in 2005-6. We performed two separate molecular epidemiological studies, spoligotyping 44 strains in a first study, and spoligotyping 131 strains, followed by MIRU-VNTR 15 on 21 clustered isolates in the second. With spoligotyping, the most common patterns were Shared International Type SIT17 (21%); SIT42 (15%); SIT93 (11%); SIT20 (7%); SIT53 (6%), a distribution similar to other parts of Venezuela, except that SIT42 and SIT20 were more common. MIRU-VNTR 15 showed that six of seven SIT17 strains examined belonged to a large cluster previously found circulating in Venezuela, but all of the SIT42 strains were related to a cluster centered in the neighborhoods of Unión and Maca, with a MIRU-VNTR pattern not previously seen in Venezuela. It appears that a large percentage of the tuberculosis in the Sucre municipality is caused by the active transmission of two strain families centered within distinct neighborhoods, one reflecting communication with the rest of the country, and the other suggesting the insular, isolated nature of some sectors.

Transboundary Groundwater Body Karavanke/Karawanken Between Austria and Slovenia

NASA Astrophysics Data System (ADS)

Brencic, M.; Poltnig, W.

2009-04-01

Large part of the border region between Republic of Slovenia and Republic of Austria is represented by high east west extended mountainous ridge of Karavanke/Karawanken. It is a range extending along the Slovenian-Austrian border for almost 150 km. Its terrain consists of long and prominent ridges, whose slopes steeply fall to the northern and southern side. Ridges are interrupted by long, deep and narrow valleys. The highest peaks reach over 2000 m above sea level. In the entire range prominent ridges with mountain meadows and forests prevail. The area is scarcely populated, the main economic activities are grazing and forestry, in some places tourism is also developing, especially winter sports centres. Karavanke/Karawanken lies on the contact between two continental plates, the large European plate in the north and the smaller Adriatic plate in the south. When the Adriatic plate was thrusted over the European one towards the north, the collision resulted in the folding of sediments previously deposited in the space between the plates. The contact of both plates caused large lateral displacements, causing the rocks of both plates to fold and fault and then extend along the contact. This is the area of Periadriatic lineament, dividing Karavanke/Karawanken range into their north and south part. Periadriatic lineament is large stripe slip tectonic structure along which on the northern side rocks were extruded to the east and on the southern side to the west. Along the lineament metamorphic (e.g. biotitic and feldsparic para-gneis, amfibolites) and magmatic (e.g. diabaz, granite and tonalite) rocks of various ages are present. Palaeozoic sedimentary rocks cover large part of the mountain ridge. The oldest are Silurian and Ordovician limestone on the northern border followed by Devonian ridge limestones. They are covered by molasse sedimentation in Carbon and shallow marine and river predominantly clastic sedimentation in Perm. The most abundant and with numerous varieties are rocks from Triassic age. In general they can be divided into rocks of Northern and Southern Karavanke/Karawanken deposited in different sedimentation basins. In lower part clastic rocks prevail, going into the upper part of Triassic age more and more carbonate rocks are present. In Southern Karavanke/Karawanken sedimentary rocks formed in the deeper part as well as on the carbonate platform are present, however in Northern Karavanke/Karawanken sedimentary rocks of shallower sedimentary environment are predominant. In the upper Triassic part of Northern Karavanke/Karawanken large zinc and lead ore deposits were formed. Among younger rocks only small patches are present. The most abundant are Rosenbacher coal-bearing beads of Jauntal/Juna in Austria of Miocen age where the uplift history of Karavanke/Karawanken is very well reflected. Extensive Quaternary sediments are present as slope sediments and sediments filling deep valleys. At the end of the 20th century decision was made to construct a 7,8 km long road tunnel through Karavanke/Karawanken between Hrušica on the Slovenian side and Rosenbach/Podrožca on the Austrian side. It was established already during the construction that waters flowing from the tunnel represent an important water resource. In Slovenia some of these springs were captured and led into the water supply network, while in Austria they remained well protected water resource for the future. Such important water resources require protection, which in turn demands knowledge about their recharge areas. This fact stimulated authorities of both countries to support the beginning of hydrogeological investigations in the west Karavanke/Karawanken region through the common ''Drava/Drau water-management commission'' and subcommission "Drinking water reserves of Karavanke/Karawanken mountains". During hydrogeological investigations detailed hydrogeological mapping of the whole Karavanke/Karawanken ridge was made. Sampling of important springs and low water discharge measurements followed this stage. Samples were taken for basic chemistry and stable isotope determination of water as well as some more sophisticated analyses (e.g. isotope analyses of noble gases) in the area of mineral waters appearance. Important part of investigations was production and compilation of new geological map based on older published and unpublished geological maps from both sides of the state border. This map represented background for the definition of hydrogeological and other detailed and specific maps (e.g. risk potential and vulnerability maps). Based on these results basic hydrological balance of the area was calculated, identification of cross border flow was performed and finally protection measures were suggested. A large part of Karavanke/Karawanken is built from karstified carbonate rocks of limestone and dolomite with underlying Paleozoic limestones. The largest part of karstified rocks lies in the area of North Karavanke/Karawanken, the Košuta unit and the Kamnik-Savinja Alps. About 3600 springs were recorded in the area of Karavanke/Karawanken on both sides of the Austrian-Slovenian state border from 1990 to 2002. For each spring, water flow, electrical conductivity and water temperature were determined. Mostly the springs have a small water flow. Only some very large springs flowing from a karstic aquifer were found to have a recharge area extending across the state border. In 2004 based on the bilateral agreement between Republic of Slovenia and Republic of Austria the common transboundary groundwater body Karavanke/Karawanken was defined. The body is defined according to the Water Framework Directive requirements and extends to the area of the main border ridge. It is divided on areas, where prevails the surface water outflow, which depends only on the surface form and areas, where groundwater outflow is present. Within the area of common water body of the Karavanke/Karawanken five cross-border aquifers were determined.

Simulation research on the process of large scale ship plane segmentation intelligent workshop

NASA Astrophysics Data System (ADS)

Xu, Peng; Liao, Liangchuang; Zhou, Chao; Xue, Rui; Fu, Wei

2017-04-01

Large scale ship plane segmentation intelligent workshop is a new thing, and there is no research work in related fields at home and abroad. The mode of production should be transformed by the existing industry 2.0 or part of industry 3.0, also transformed from "human brain analysis and judgment + machine manufacturing" to "machine analysis and judgment + machine manufacturing". In this transforming process, there are a great deal of tasks need to be determined on the aspects of management and technology, such as workshop structure evolution, development of intelligent equipment and changes in business model. Along with them is the reformation of the whole workshop. Process simulation in this project would verify general layout and process flow of large scale ship plane section intelligent workshop, also would analyze intelligent workshop working efficiency, which is significant to the next step of the transformation of plane segmentation intelligent workshop.

The Gould's Belt very large array survey. III. The Orion region

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kounkel, Marina; Hartmann, Lee; Loinard, Laurent

2014-07-20

We present results from a high-sensitivity (60 μJy), large-scale (2.26 deg{sup 2}) survey obtained with the Karl G. Jansky Very Large Array as part of the Gould's Belt Survey program. We detected 374 and 354 sources at 4.5 and 7.5 GHz, respectively. Of these, 148 are associated with previously known young stellar objects (YSOs). Another 86 sources previously unclassified at either optical or infrared wavelengths exhibit radio properties that are consistent with those of young stars. The overall properties of our sources at radio wavelengths such as their variability and radio to X-ray luminosity relation are consistent with previous resultsmore » from the Gould's Belt Survey. Our detections provide target lists for follow-up Very Long Baseline Array radio observations to determine their distances as YSOs are located in regions of high nebulosity and extinction, making it difficult to measure optical parallaxes.« less

Wind-Tunnel Tests on a Series of Wing Models Through a Large Angle of Attack Range. Part I : Force Tests

NASA Technical Reports Server (NTRS)

Knight, Montgomery; Wenzinger, Carl J

1930-01-01

This investigation covers force tests through a large range of angle of attack on a series of monoplane and biplane wing models. The tests were conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The models were arranged in such a manner as to make possible a determination of the effects of variations in tip shape, aspect ratio, flap setting, stagger, gap, decalage, sweep back, and airfoil profile. The arrangements represented most of the types of wing systems in use on modern airplanes. The effect of each variable is illustrated by means of groups of curves. In addition, there are included approximate autorotational characteristics in the form of calculated ranges of "rotary instability." a correction for blocking in this tunnel which applies to monoplanes at large angles of attack has been developed, and is given in an appendix. (author)

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplane

NASA Technical Reports Server (NTRS)

Silverstein, Abe; Wilson, Herbert A , Jr

1942-01-01

An investigation was conducted in the NACA full-scale wind tunnel to determine the drag and the propulsive efficiency of nacelle-propeller arrangements for a large range of nacelle sizes. In contrast with usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a four-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplanes weighing from about 20 to 100 tons. The results show the drag, the propulsive efficiency, and the over-all efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model is shown for both propeller-removed and propeller-operating conditions.

The Gould's Belt Very Large Array Survey. III. The Orion Region

NASA Astrophysics Data System (ADS)

Kounkel, Marina; Hartmann, Lee; Loinard, Laurent; Mioduszewski, Amy J.; Dzib, Sergio A.; Ortiz-León, Gisela N.; Rodríguez, Luis F.; Pech, Gerardo; Rivera, Juana L.; Torres, Rosa M.; Boden, Andrew F.; Evans, Neal J., II; Briceño, Cesar; Tobin, John

2014-07-01

We present results from a high-sensitivity (60 μJy), large-scale (2.26 deg2) survey obtained with the Karl G. Jansky Very Large Array as part of the Gould's Belt Survey program. We detected 374 and 354 sources at 4.5 and 7.5 GHz, respectively. Of these, 148 are associated with previously known young stellar objects (YSOs). Another 86 sources previously unclassified at either optical or infrared wavelengths exhibit radio properties that are consistent with those of young stars. The overall properties of our sources at radio wavelengths such as their variability and radio to X-ray luminosity relation are consistent with previous results from the Gould's Belt Survey. Our detections provide target lists for follow-up Very Long Baseline Array radio observations to determine their distances as YSOs are located in regions of high nebulosity and extinction, making it difficult to measure optical parallaxes.

Three-wave mixing in conjugated polymer solutions: Two-photon absorption in polydiacetylenes

NASA Astrophysics Data System (ADS)

Chance, R. R.; Shand, M. L.; Hogg, C.; Silbey, R.

1980-10-01

Three-wave-mixing spectroscopy is used to determine the dispersive and absorptive parts of a strongly allowed two-photon transition in a series of polydiacetylene solutions. The data analysis yields the energy, width, symmetry assignment, and oscillator strength for the two-photon transition. The data conclusively demonstrate that strong two-photon absorption is a fundamental property of the polydiacetylene backbone. The remarkably large two-photon absorption coefficients are explained by large oscillator strengths for both transitions involved in the two-photon absorption combined with strong one-photon resonance effects. The experimental results are shown to be consistent with a simple theoretical model for the energies and oscillator strengths of the one- and two-photon-allowed transitions.

Radar imaging of volcanic fields and sand dune fields: Implications for VOIR

NASA Technical Reports Server (NTRS)

Elachi, C.; Blom, R.; Daily, M.; Farr, T.; Saunders, R. S.

1980-01-01

A number of volcanic fields and sand dune fields in the western part of North America were studied using aircraft and Seasat synthetic aperture radar images and LANDSAT images. The capability of radars with different characteristics (i.e., frequency, polarization and look angles was assessed to identify and map different volcanic features, lava flows and sand dune types. It was concluded that: (1) volcanic features which have a relatively large topographic expression (i.e., cinder cones, collapse craters, calderas, etc.) are easily identified; (2) lava flows of different ages can be identified, particularly on the L-band images; and (3) sand dunes are clearly observed and their extent and large scale geometric characteristics determined, provided the proper imaging geometry exists.

Cancer prevention clinical trials.

PubMed

Nixon, D W

1994-01-01

Many kinds of cancer are preventable. Avoidance of tobacco would essentially eliminate lung cancer and most head and neck cancers as well. Other common cancers (breast, colon, prostate) are related to diet and therefore may also be preventable, at least in part. Abundant epidemiologic and laboratory data link specific nutrients including fat, fiber and vitamins to cancer so that appropriate manipulation of these constituents might reduce cancer risk. Determination of appropriate manipulations requires prospective clinical trials in humans. Approximately 40 such trials are in progress. Some have been completed with encouraging results. Future large scale trials will require designs that overcome the barriers of cost, large subject numbers and long study duration. The use of "intermediate markers" rather than cancer end points is a strategy that will help overcome these barriers.

A method for surface topography measurement using a new focus function based on dual-tree complex wavelet transform

NASA Astrophysics Data System (ADS)

Li, Shimiao; Guo, Tong; Yuan, Lin; Chen, Jinping

2018-01-01

Surface topography measurement is an important tool widely used in many fields to determine the characteristics and functionality of a part or material. Among existing methods for this purpose, the focus variation method has proved high performance particularly in large slope scenarios. However, its performance depends largely on the effectiveness of focus function. This paper presents a method for surface topography measurement using a new focus measurement function based on dual-tree complex wavelet transform. Experiments are conducted on simulated defocused images to prove its high performance in comparison with other traditional approaches. The results showed that the new algorithm has better unimodality and sharpness. The method was also verified by measuring a MEMS micro resonator structure.

Identification and determination of the contribution of iron-steel manufacturing industry to sediment-associated polycyclic aromatic hydrocarbons (PAHs) in a large shallow lake of eastern China.

PubMed

Zhang, Liu; Bai, Ya-Shu; Wang, Ji-Zhong; Peng, Shu-Chuan; Chen, Tian-Hu; Yin, Da-Qiang

2016-11-01

Seventeen polycyclic aromatic hydrocarbon (PAH) compounds were determined in surface sediments collected from the Chaohu Lake (a large shallow lake in eastern China) and its tributaries. Both diagnostic ratios and a receptor model (positive matrix factorization, PMF) were applied to identify and determine the contribution of a local iron-steel manufacturing plant located in the Nanfei River (NFR) to the Chaohu Lake basin. The results show that sites located in the downstream of the steel plant contained concentrations of 17 PAH (Σ 17 PAH) approximately two orders of magnitudes higher than those from other sites. Five factors were identified by the PMF model, including industrial waste, wood/biomass burning, diagenetic origin, domestic coal combustion, and industrial combustion. Our findings suggest that sediments in the downstream of the plant and in the western part of the Chaohu Lake were predominantly affected by industrial coal combustion. A mixture of pyrolytic origins impacted urban sediments in the upstream of the plant, whereas diagenetic origins along with coal and biomass burning were suggested to influence the eastern part and rural tributaries of the lake. To assess the potential ecological risk and toxicity caused by the iron-steel plant, sediment toxicity was evaluated by the PMF model, sediment quality guideline, and toxic equivalent factors. All of the three approaches suggested PAH accumulation in the NFR sediments could produce significant adverse ecological effects and half of the sediment toxicity in the NFR may be attributed to the emissions from the iron-steel plant. Some rural locations also exhibited PAH concentrations above probable effects, most likely contributed by wood/biomass burning.

Predictability of Circulation Transitions (Observed and Modeled): Non-diffusive Dynamics, Markov Chains and Error Growth.

NASA Astrophysics Data System (ADS)

Straus, D. M.

2006-12-01

The transitions between portions of the state space of the large-scale flow is studied from daily wintertime data over the Pacific North America region using the NCEP reanalysis data set (54 winters) and very large suites of hindcasts made with the COLA atmospheric GCM with observed SST (55 members for each of 18 winters). The partition of the large-scale state space is guided by cluster analysis, whose statistical significance and relationship to SST is reviewed (Straus and Molteni, 2004; Straus, Corti and Molteni, 2006). The determination of the global nature of the flow through state space is studied using Markov Chains (Crommelin, 2004). In particular the non-diffusive part of the flow is contrasted in nature (small data sample) and the AGCM (large data sample). The intrinsic error growth associated with different portions of the state space is studied through sets of identical twin AGCM simulations. The goal is to obtain realistic estimates of predictability times for large-scale transitions that should be useful in long-range forecasting.

Relative availability of natural prey versus livestock predicts landscape suitability for cheetahs Acinonyx jubatus in Botswana

PubMed Central

Winterbach, Christiaan W.; Boast, Lorraine K.; Klein, Rebecca; Somers, Michael J.

2015-01-01

Prey availability and human-carnivore conflict are strong determinants that govern the spatial distribution and abundance of large carnivore species and determine the suitability of areas for their conservation. For wide-ranging large carnivores such as cheetahs (Acinonyx jubatus), additional conservation areas beyond protected area boundaries are crucial to effectively conserve them both inside and outside protected areas. Although cheetahs prefer preying on wild prey, they also cause conflict with people by predating on especially small livestock. We investigated whether the distribution of cheetahs’ preferred prey and small livestock biomass could be used to explore the potential suitability of agricultural areas in Botswana for the long-term persistence of its cheetah population. We found it gave a good point of departure for identifying priority areas for land management, the threat to connectivity between cheetah populations, and areas where the reduction and mitigation of human-cheetah conflict is critical. Our analysis showed the existence of a wide prey base for cheetahs across large parts of Botswana’s agricultural areas, which provide additional large areas with high conservation potential. Twenty percent of wild prey biomass appears to be the critical point to distinguish between high and low probable levels of human-cheetah conflict. We identified focal areas in the agricultural zones where restoring wild prey numbers in concurrence with effective human-cheetah conflict mitigation efforts are the most immediate conservation strategies needed to maintain Botswana’s still large and contiguous cheetah population. PMID:26213646

Relative availability of natural prey versus livestock predicts landscape suitability for cheetahs Acinonyx jubatus in Botswana.

PubMed

Winterbach, Hanlie E K; Winterbach, Christiaan W; Boast, Lorraine K; Klein, Rebecca; Somers, Michael J

2015-01-01

Prey availability and human-carnivore conflict are strong determinants that govern the spatial distribution and abundance of large carnivore species and determine the suitability of areas for their conservation. For wide-ranging large carnivores such as cheetahs (Acinonyx jubatus), additional conservation areas beyond protected area boundaries are crucial to effectively conserve them both inside and outside protected areas. Although cheetahs prefer preying on wild prey, they also cause conflict with people by predating on especially small livestock. We investigated whether the distribution of cheetahs' preferred prey and small livestock biomass could be used to explore the potential suitability of agricultural areas in Botswana for the long-term persistence of its cheetah population. We found it gave a good point of departure for identifying priority areas for land management, the threat to connectivity between cheetah populations, and areas where the reduction and mitigation of human-cheetah conflict is critical. Our analysis showed the existence of a wide prey base for cheetahs across large parts of Botswana's agricultural areas, which provide additional large areas with high conservation potential. Twenty percent of wild prey biomass appears to be the critical point to distinguish between high and low probable levels of human-cheetah conflict. We identified focal areas in the agricultural zones where restoring wild prey numbers in concurrence with effective human-cheetah conflict mitigation efforts are the most immediate conservation strategies needed to maintain Botswana's still large and contiguous cheetah population.

New routes to the functionalization patterning and manufacture of graphene-based materials for biomedical applications.

PubMed

De Sanctis, A; Russo, S; Craciun, M F; Alexeev, A; Barnes, M D; Nagareddy, V K; Wright, C D

2018-06-06

Graphene-based materials are being widely explored for a range of biomedical applications, from targeted drug delivery to biosensing, bioimaging and use for antibacterial treatments, to name but a few. In many such applications, it is not graphene itself that is used as the active agent, but one of its chemically functionalized forms. The type of chemical species used for functionalization will play a key role in determining the utility of any graphene-based device in any particular biomedical application, because this determines to a large part its physical, chemical, electrical and optical interactions. However, other factors will also be important in determining the eventual uptake of graphene-based biomedical technologies, in particular the ease and cost of manufacture of proposed device and system designs. In this work, we describe three novel routes for the chemical functionalization of graphene using oxygen, iron chloride and fluorine. We also introduce novel in situ methods for controlling and patterning such functionalization on the micro- and nanoscales. Our approaches are readily transferable to large-scale manufacturing, potentially paving the way for the eventual cost-effective production of functionalized graphene-based materials, devices and systems for a range of important biomedical applications.

Signalling networks and dynamics of allosteric transitions in bacterial chaperonin GroEL: implications for iterative annealing of misfolded proteins.

PubMed

Thirumalai, D; Hyeon, Changbong

2018-06-19

Signal transmission at the molecular level in many biological complexes occurs through allosteric transitions. Allostery describes the responses of a complex to binding of ligands at sites that are spatially well separated from the binding region. We describe the structural perturbation method, based on phonon propagation in solids, which can be used to determine the signal-transmitting allostery wiring diagram (AWD) in large but finite-sized biological complexes. Application to the bacterial chaperonin GroEL-GroES complex shows that the AWD determined from structures also drives the allosteric transitions dynamically. From both a structural and dynamical perspective these transitions are largely determined by formation and rupture of salt-bridges. The molecular description of allostery in GroEL provides insights into its function, which is quantitatively described by the iterative annealing mechanism. Remarkably, in this complex molecular machine, a deep connection is established between the structures, reaction cycle during which GroEL undergoes a sequence of allosteric transitions, and function, in a self-consistent manner.This article is part of a discussion meeting issue 'Allostery and molecular machines'. © 2018 The Author(s).

Meson-nucleus potentials and the search for meson-nucleus bound states

NASA Astrophysics Data System (ADS)

Metag, V.; Nanova, M.; Paryev, E. Ya.

2017-11-01

Recent experiments studying the meson-nucleus interaction to extract meson-nucleus potentials are reviewed. The real part of the potentials quantifies whether the interaction is attractive or repulsive while the imaginary part describes the meson absorption in nuclei. The review is focused on mesons which are sufficiently long-lived to potentially form meson-nucleus quasi-bound states. The presentation is confined to meson production off nuclei in photon-, pion-, proton-, and light-ion induced reactions and heavy-ion collisions at energies near the production threshold. Tools to extract the potential parameters are presented. In most cases, the real part of the potential is determined by comparing measured meson momentum distributions or excitation functions with collision model or transport model calculations. The imaginary part is extracted from transparency ratio measurements. Results on K+ ,K0 ,K- , η ,η‧ , ω, and ϕ mesons are presented and compared with theoretical predictions. The interaction of K+ and K0 mesons with nuclei is found to be weakly repulsive, while the K- , η ,η‧ , ω and ϕ meson-nucleus potentials are attractive, however, with widely different strengths. Because of meson absorption in the nuclear medium the imaginary parts of the meson-nucleus potentials are all negative, again with a large spread. An outlook on planned experiments in the charm sector is given. In view of the determined potential parameters, the criteria and chances for experimentally observing meson-nucleus quasi-bound states are discussed. The most promising candidates appear to be the η and η‧ mesons.

Avalanche ecology and large magnitude avalanche events: Glacier National Park, Montana, USA

USGS Publications Warehouse

Fagre, Daniel B.; Peitzsch, Erich H.

2010-01-01

Large magnitude snow avalanches play an important role ecologically in terms of wildlife habitat, vegetation diversity, and sediment transport within a watershed. Ecological effects from these infrequent avalanches can last for decades. Understanding the frequency of such large magnitude avalanches is also critical to avalanche forecasting for the Going-to-the-Sun Road (GTSR). In January 2009, a large magnitude avalanche cycle occurred in and around Glacier National Park, Montana. The study site is the Little Granite avalanche path located along the GTSR. The study is designed to quantify change in vegetative cover immediately after a large magnitude event and document ecological response over a multi-year period. GPS field mapping was completed to determine the redefined perimeter of the avalanche path. Vegetation was inventoried using modified U.S. Forest Service Forest Inventory and Analysis plots, cross sections were taken from over 100 dead trees throughout the avalanche path, and an avalanche chronology was developed. Initial results indicate that the perimeter of this path was expanded by 30%. The avalanche travelled approximately 1200 vertical meters and 3 linear kilometers. Stands of large conifers as old as 150 years were decimated by the avalanche, causing a shift in dominant vegetation types in many parts of the avalanche path. Woody debris is a major ground cover up to 3 m in depth on lower portions of the avalanche path and will likely affect tree regrowth. Monitoring and measuring the post-avalanche vegetation recovery of this particular avalanche path provides a unique dataset for determining the ecological role of avalanches in mountain landscapes.

19 CFR Appendix C to Part 113 - Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows

Code of Federal Regulations, 2014 CFR

2014-04-01

... for Sale at United States Boat Shows C Appendix C to Part 113 Customs Duties U.S. CUSTOMS AND BORDER... Appendix C to Part 113—Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows ____, as...

19 CFR Appendix C to Part 113 - Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows

Code of Federal Regulations, 2013 CFR

2013-04-01

... for Sale at United States Boat Shows C Appendix C to Part 113 Customs Duties U.S. CUSTOMS AND BORDER... Appendix C to Part 113—Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows ____, as...

19 CFR Appendix C to Part 113 - Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows

Code of Federal Regulations, 2012 CFR

2012-04-01

... for Sale at United States Boat Shows C Appendix C to Part 113 Customs Duties U.S. CUSTOMS AND BORDER... Appendix C to Part 113—Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows ____, as...

Heterogeneity in relaxation of different sized porcine coronary arteries to nitrovasodilators: role of PKG and MYPT1.

PubMed

Ying, Lei; Xu, Xiaojian; Liu, Juan; Dou, Dou; Yu, Xiaoxing; Ye, Liping; He, Qiong; Gao, Yuansheng

2012-02-01

The present study was to determine the role of the type I isoform of cGMP-dependent protein kinase (PKG I) and its downstream effector myosin phosphatase target subunit 1 (MYPT1) in the responses of different sized coronary arteries to nitrovasodilators. Relaxations of isolated porcine coronary arteries were determined by isometric tension recording technique. Protein levels of PKG I and its effectors were analyzed by Western blotting. The activities of PKG I and MYPT1 were studied by analyzing phosphorylation of vasodilator-stimulated phosphoprotein (VASP) and MYPT1, respectively. Nitroglycerin, DETA NONOate, and 8-Br-cGMP caused greater relaxations in large than in small coronary arteries. Relaxations were attenuated to a greater extent by Rp-8-Br-PET-cGMPS (a PKG inhibitor) in large vs. small arteries. The expressions of PKG I and MYPT1 in large arteries were more abundant than in small arteries. DETA NONOate stimulated phosphorylation of VASP at Ser239 and inhibited phosphorylation of MYPT1 at Thr853 to a greater extent in large than in small arteries. A suppressed phosphorylation of MYPT1 at Thr853 was caused by 8-Br-cGMP in large but not small arteries, which was inhibited by Rp-8-Br-PET-cGMPS. These results suggest that the greater responsiveness of large coronary arteries to nitrovasodilators result in part from greater activities of PKG I and MYPT1. Dysfunction in nitric oxide signaling is implicated in the vulnerability of large coronary arteries to certain disorders such as atherosclerosis and spasm. Augmentation of PKG I-MYPT1 signaling may be of therapeutic benefit for combating these events.

Test and Evaluation of the Surveyor 3 Television Camera Returned from the Moon by Apollo 12. Volume 1

NASA Technical Reports Server (NTRS)

1970-01-01

Results are presented of engineering tests of the Surveyor III television camera, which resided on the moon for 2 and 1/2 years before being brought back to earth by the Apollo XII astronauts. Electric circuits, electrical, mechanical, and optical components and subsystems, the vidicon tube, and a variety of internal materials and surface coatings were examined to determine the effects of lunar exposure. Anomalies and failures uncovered were analyzed. For the most part, the camera parts withstood the extreme environment exceedingly well except where degradation of obsolete parts or suspect components had been anticipated. No significant evidence of cold welding was observed, and the anomalies were largely attributable to causes other than lunar exposure. Very little evidence of micrometeoroid impact was noted. Discoloration of material surfaces -- one of the major effects noted--was found to be due to lunar dust contamination and radiation damage. The extensive test data contained in this report are supplemented by results of tests of other Surveyor parts retrieved by the Apollo XII astronauts, which are contained in a companion report.

Tobacco control and gender in Southeast Asia. Part I: Malaysia and the Philippines.

PubMed

Morrow, Martha; Barraclough, Simon

2003-09-01

In the World Health Organization's Western Pacific Region, being born male is the single greatest risk marker for tobacco use. While the literature demonstrates that risks associated with tobacco use may vary according to sex, gender refers to the socially determined roles and responsibilities of men and women, who initiate, continue and quit using tobacco for complex and often different reasons. Cigarette advertising frequently appeals to gender roles. Yet tobacco control policy tends to be gender-blind. Using a broad gender-sensitivity framework, this contradiction is explored in four Western Pacific countries. Part I of the study discusses issues surrounding gender and tobacco, and analyses developments in Malaysia and the Philippines. Part II deals with Singapore and Vietnam. In all four countries, gender was salient for the initiation and maintenance of smoking, and in Malaysia and the Philippines was highly significant in cigarette promotion. Yet, with a few exceptions, gender was largely unrecognized in control policy. Suggestions for overcoming this weakness in order to enhance tobacco control are made in Part II.

Psychosocial determinants of premature cardiovascular mortality differences within Hungary.

PubMed

Kopp, Maria; Skrabski, Arpád; Szántó, Zsuzsa; Siegrist, Johannes

2006-09-01

The life expectancy gap between Central-Eastern European (CEE) countries, including Hungary, and Western Europe (WE) is mainly attributable to excess cardiovascular (CV) mortality in midlife. This study explores the contribution of socioeconomic, work related, psychosocial, and behavioural variables to explaining variations of middle aged male and female CV mortality across 150 sub-regions in Hungary. Cross sectional, ecological analyses. 150 sub-regions of Hungary. 12 643 people were interviewed in Hungarostudy 2002 survey, representing the Hungarian population according to sex, age, and sub-regions. Independent variables were income, education, control in work, job insecurity, weekend working hours, social support, depression, hostility, anomie, smoking, body mass index, and alcohol misuse. Gender specific standardised premature (45-64 years) total CV, ischaemic heart disease, and cerebrovascular mortality rates in 150 sub-regions of Hungary. Low education and income were the most important determinants of mid-aged CV mortality differences across sub-regions. High weekend workload, low social support at work, and low control at work account for a large part of variation in male premature CV mortality rates, whereas job insecurity, high weekend workload, and low control at work contribute most noticeably to variations in premature CV mortality rates among women. Low social support from friends, depression, anomie, hostility, alcohol misuse and cigarette smoking can also explain a considerable part of variations of premature CV mortality differences. Variations in middle aged CV mortality rates in a rapidly changing society in CEE are largely accounted for by distinct unfavourable working and other psychosocial stress conditions.

40 CFR Table 1 to Subpart Hhh of... - Emission Limits for Small Rural, Small, Medium, and Large HMIWI

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Medium, and Large HMIWI 1 Table 1 to Subpart HHH of Part 62 Protection of Environment ENVIRONMENTAL... Part 62—Emission Limits for Small Rural, Small, Medium, and Large HMIWI For the air pollutant You must meet this emissions limit HMIWI size Small rural Small Medium Large With these units(7 percent oxygen...

40 CFR Table 1 to Subpart Hhh of... - Emissions Limits for Small Rural, Small, Medium and Large HMIWI

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Medium and Large HMIWI 1 Table 1 to Subpart HHH of Part 62 Protection of Environment ENVIRONMENTAL... Part 62—Emissions Limits for Small Rural, Small, Medium and Large HMIWI For the air pollutant You must meet this emissions limit HMIWI size Small rural Small Medium Large With these units(7 percent oxygen...

High precision slotted cavity measurement of a novel ceramic state polymer electrolyte

NASA Astrophysics Data System (ADS)

Quan, Wei; NurulAfsar, Mohammed

2018-01-01

Thin film materials are already used in a variety of microwave and higher frequency applications such as electrically tunable microwave devices, integrated circuits like MMICs, radomes, and radar absorbing coating. The determination of the dielectric properties of these films is thus of significant importance. The measurement of complex dielectric permittivity of thin films is very difficult at microwave, millimeter, and THz frequencies because both the amplitude change and phase shift are not large enough to evaluate the real part of the dielectric permittivity. A specially designed transverse slotted cavity for X-band microwave measurement has been designed and constructed to employ with a vector network analyzer to evaluate the real part of dielectric permittivity of thin films accurately and conveniently. Commercially available polymer thin films are measured to validate the methods.

Survey and Assessment of Models or Decision Rules Determining Spare Parts Levels for Navy Electronics Equipments. Appendix A. Applicable Literature Source Material.

DTIC Science & Technology

1979-09-07

1$.It .400 0 4 U 0 go oil 9999 0003,68 C0.rroCl.LF611F1. L4 1*6 .400o G0 s0 U 0 of 96 420 0033092,c S6art 311104L.Pump IS 9706* .&see t I IS 0 00 to...of the modcLI a large number dt reair part cla~ses were defined oil thle ai tf notnenl~tnr and hir each ch"~ 6 and IS m ere comnputed fnm &P. avznak...simi- applie:Ltious ill .I larly, we find n3*-4 and n*-. Thus, if c:VI’ :, of (9), the oIl il.: - % R. Optimal Redundancy 587 h~ type used during From n

Instantons and Large N

NASA Astrophysics Data System (ADS)

Mariño, Marcos

2015-09-01

Preface; Part I. Instantons: 1. Instantons in quantum mechanics; 2. Unstable vacua in quantum field theory; 3. Large order behavior and Borel summability; 4. Non-perturbative aspects of Yang-Mills theories; 5. Instantons and fermions; Part II. Large N: 6. Sigma models at large N; 7. The 1=N expansion in QCD; 8. Matrix models and matrix quantum mechanics at large N; 9. Large N QCD in two dimensions; 10. Instantons at large N; Appendix A. Harmonic analysis on S3; Appendix B. Heat kernel and zeta functions; Appendix C. Effective action for large N sigma models; References; Author index; Subject index.

Anchorage failure of young trees in sandy soils is prevented by a rigid central part of the root system with various designs.

PubMed

Danquechin Dorval, Antoine; Meredieu, Céline; Danjon, Frédéric

2016-07-25

Storms can cause huge damage to European forests. Even pole-stage trees with 80-cm rooting depth can topple. Therefore, good anchorage is needed for trees to survive and grow up from an early age. We hypothesized that root architecture is a predominant factor determining anchorage failure caused by strong winds. We sampled 48 seeded or planted Pinus pinaster trees of similar aerial size from four stands damaged by a major storm 3 years before. The trees were gathered into three classes: undamaged, leaning and heavily toppled. After uprooting and 3D digitizing of their full root architectures, we computed the mechanical characteristics of the main components of the root system from our morphological measurements. Variability in root architecture was quite large. A large main taproot, either short and thick or long and thin, and guyed by a large volume of deep roots, was the major component that prevented stem leaning. Greater shallow root flexural stiffness mainly at the end of the zone of rapid taper on the windward side also prevented leaning. Toppling in less than 90-cm-deep soil was avoided in trees with a stocky taproots or with a very big leeward shallow root. Toppled trees also had a lower relative root biomass - stump excluded - than straight trees. It was mainly the flexural stiffness of the central part of the root system that secured anchorage, preventing a weak displacement of the stump. The distal part of the longest taproot and attached deep roots may be the only parts of the root system contributing to anchorage through their maximum tensile load. Several designs provided good anchorage, depending partly on available soil depth. Pole-stage trees are in-between the juvenile phase when they fail by toppling and the mature phase when they fail by uprooting. © The Author 2016. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Analysis of physical activity mass media campaign design.

PubMed

Lankford, Tina; Wallace, Jana; Brown, David; Soares, Jesus; Epping, Jacqueline N; Fridinger, Fred

2014-08-01

Mass media campaigns are a necessary tool for public health practitioners to reach large populations and promote healthy behaviors. Most health scholars have concluded that mass media can significantly influence the health behaviors of populations; however the effects of such campaigns are typically modest and may require significant resources. A recent Community Preventive Services Task Force review on stand-alone mass media campaigns concluded there was insufficient evidence to determine their effectiveness in increasing physical activity, partly due to mixed methods and modest and inconsistent effects on levels of physical activity. A secondary analysis was performed on the campaigns evaluated in the Task Force review to determine use of campaign-building principles, channels, and levels of awareness and their impact on campaign outcomes. Each study was analyzed by 2 reviewers for inclusion of campaign building principles. Campaigns that included 5 or more campaign principles were more likely to be successful in achieving physical activity outcomes. Campaign success is more likely if the campaign building principles (formative research, audience segmentation, message design, channel placement, process evaluation, and theory-based) are used as part of campaign design and planning.

Determination of Se in soil samples using the proton induced X-ray emission technique

NASA Astrophysics Data System (ADS)

Cruvinel, Paulo E.; Flocchini, Robert G.

1993-04-01

An alternative method for the direct determination of total Se in soil samples is presented. A large number of trace elements is present in soil at concentration values in the range of part per billion and tenths of parts of million. The most common are the trace elements of Al, Si, K, Ca, Ti, V, Cr, Fe, Cu, Zn, Br, Rb, Mo, Cd and Pb. As for biological samples many of these elements are of great importance for the nutrition of plants, while others are toxic and others have an unknown role. Selenium is an essential micronutrient for humans and animals but it is also known that in certain areas Se deficiency or toxicity has caused endemic disease to livestock and humans through the soil-plant-animal linkage. In this work the suitability of the proton induced X-ray emission (PIXE) technique as a fast and nondestructive technique useful to measure total the Se content in soil samples is demonstrated. To validate the results a comparison of data collected using the conventional atomic absorption spectrophotometry (AAS) method was performed.

Electron spin resonance analysis of tooth enamel does not indicate exposures to large radiation doses in a large proportion of distally-exposed A-bomb survivors.

PubMed

Hirai, Yuko; Kodama, Yoshiaki; Cullings, Harry M; Miyazawa, Chuzo; Nakamura, Nori

2011-01-01

The atomic bombs in Hiroshima and Nagasaki led to two different types of radiation exposure; one was direct and brief and the other was indirect and persistent. The latter (so-called exposure to residual radiation) resulted from the presence of neutron activation products in the soil, or from fission products present in the fallout. Compared with the doses from direct exposures, estimations of individual doses from residual radiation have been much more complicated, and estimates vary widely among researchers. The present report bases its conclusions on radiation doses recorded in tooth enamel from survivors in Hiroshima. Those survivors were present at distances of about 3 km or greater from the hypocenter at the time of the explosion, and have DS02 estimated doses (direct exposure doses) of less than 5 mGy (and are regarded as control subjects). Individual doses were estimated by measuring CO(2)(-) radicals in tooth enamel with the electron spin resonance (ESR; or electron paramagnetic resonance, EPR) method. The results from 56 molars donated by 49 survivors provided estimated doses which vary from -200 mGy to 500 mGy, and the median dose was 17 mGy (25% and 75% quartiles are -54 mGy and 137 mGy, respectively) for the buccal parts and 13 mGy (25% and 75% quartiles: -49 mGy and 87 mGy, respectively) for the lingual parts of the molars. Three molars had ESR-estimated doses of 300 to 400 mGy for both the buccal and lingual parts, which indicates possible exposures to excess doses of penetrating radiation, although the origin of such radiation remains to be determined. The results did not support claims that a large fraction of distally-exposed survivors received large doses (e.g. 1 Gy) of external penetrating radiation resulting from residual radiation.

Challenges with Final Status Surveys at a Large Decommissioning Site - 13417

DOE Office of Scientific and Technical Information (OSTI.GOV)

Downey, Heath; Collopy, Peter; Shephard, Eugene

2013-07-01

As part of decommissioning a former nuclear fuel manufacturing site, one of the crucial final steps is to conduct Final Status Surveys (FSS) in order to demonstrate compliance with the release criteria. At this decommissioning site, the area for FSS was about 100 hectares (248 acres) and included varying terrain, wooded areas, ponds, excavations, buildings and a brook. The challenges in performing the FSS included determining location, identifying FSS units, logging gamma walkover survey data, determining sample locations, managing water in excavations, and diverting water in the brook. The approaches taken to overcome these challenges will be presented in themore » paper. The paper will present and discuss lessons learned that will aid others in the FSS process. (authors)« less

Strategic facility planning improves capital decision making.

PubMed

Reeve, J R

2001-03-01

A large, Midwestern IDS undertook a strategic facility-planning process to evaluate its facility portfolio and determine how best to allocate future investments in facility development. The IDS assembled a facility-planning team, which initiated the planning process with a market analysis to determine future market demands and identify service areas that warranted facility expansion. The team then analyzed each of the IDS's facilities from the perspective of uniform capacity measurements, highest and best use compared with needs, building condition and investment-worthiness, and facility growth and site development opportunities. Based on results of the analysis, the strategy adopted entailed, in part, shifting some space from inpatient care to ambulatory care services and demolishing and replacing the 11 percent of facilities deemed to be in the worst condition.

40 CFR Appendix II to Part 1048 - Large Spark-ignition (SI) Composite Transient Cycle

Code of Federal Regulations, 2010 CFR

2010-07-01

... Transient Cycle II Appendix II to Part 1048 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY.... 1048, App. II Appendix II to Part 1048—Large Spark-ignition (SI) Composite Transient Cycle The following table shows the transient duty-cycle for engines that are not constant-speed engines, as described...

[Psychotherapeutically-Systemic Acting in the Integrated Family Counseling Presented by the Example of Child-Centered Educational Counseling].

PubMed

Herrmann, Ines

2015-01-01

The article gives an insight into the practice of Integrated Family Counseling and identifies their interfaces with psychotherapeutic approaches. The example of the child-centered educational counseling shows how consultancy, systemic and psychotherapeutic interventions interact in order to meet the parents educational needs defined by the parents. The first part of the article explains the term of Integrated Family Counseling, differentiates the various substantive areas of work and outlines the systematic attitude. The second part describes the psychotherapy-systemic action in the child-centered educational counseling from the perspective of the practice. Main priorities in the course of counseling, including cause-related behavioral and developmental diagnostics, play therapy intervention and parental involvement are presented. Here the systemic approach, major methodological elements as well as their effects are pointed up. The third part is devoted to the reflection of the relationship between counseling and psychotherapy. It becomes clear that in particular the intended effectiveness of an intervention determines their methodological design to a large extent.

Characterization of cumulus cloud fields using trajectories in the center of gravity versus water mass phase space: 1. Cloud tracking and phase space description: CENTER OF GRAVITY VERSUS WATER MASS 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heiblum, Reuven H.; Altaratz, Orit; Koren, Ilan

We study the evolution of warm convective cloud fields using large eddy simulations of continental and trade cumulus. Individual clouds are tracked a posteriori from formation to dissipation using a 3D cloud tracking algorithm and results are presented in the phase- space of center of gravity altitude versus cloud liquid water mass (CvM space). The CvM space is shown to contain rich information on cloud field characteristics, cloud morphology, and common cloud development pathways, together facilitating a comprehensive understanding of the cloud field. In this part we show how the meteorological (thermodynamic) conditions that determine the cloud properties are projectedmore » on the CvM phase space and how changes in the initial conditions affect the clouds' trajectories in this space. This part sets the stage for a detailed microphysical analysis that will be shown in part II.« less

Influence of clamp-up force on the strength of bolted composite joints

NASA Astrophysics Data System (ADS)

Horn, Walter J.; Schmitt, Ron R.

1994-03-01

Composite materials offer the potential for a reduction in the number of individual parts and joints in a structure because large one-piece components can replace multipart assemblies. Nevertheless, there are many situations where composite parts must be joined and often mechanical fasteners provide the only practical method of joining those parts. The long-term strength of mechanically fastened joints of composite members can be directly affected by the clamp-up force of the fastener and thus perhaps by the relaxation of this force due to the viscoelastic character of the composite materials of the joint. Methods for predicting the effect of bolt clamp-up force relaxation on the strength of mechanically fastened joints of thermoplastic composite materials were investigated during the present study. A test program, using two thermoplastic composite materials, was conducted to determine the influence of clamp-up force on joint strength, to measure the relaxation of the joint clamp-up force with time, and to measure the change of joint strength as a function of time.

Job sharing: a retention strategy for nurses.

PubMed

Kane, D

1999-01-01

Job sharing is a part-time employment alternative which offers advantages for employers interested in retaining experienced staff and nurses who are seeking a more equitable balance between work life and home life responsibilities. This quasi experimental, ex post facto research study was designed to determine if there are differences in job satisfaction, burnout, and desire to leave their position, in nurses who are employed in full-time, part-time, or job sharing positions. The sample (N = 269) was drawn from a large Canadian teaching and referral hospital. Three sample groups were developed, consisting of job sharing, full-time, and part-time nurses, respectively. Descriptive statistics were used to identify characteristics of the selected population. Analysis of variance was used to examine differences between the three employment groups on the outcome measures of job satisfaction, burnout, and desire to leave their position. The results of this study significantly support the belief that job sharing has a positive impact on job satisfaction and job retention. Implications for nursing administrators as well as individual nurses will be discussed.

Practical Tests with the "auto Control Slot." Part II : Discussion

NASA Technical Reports Server (NTRS)

Lachmann, G

1930-01-01

For some time the D.V.L. has been investigating the question of applicability of Handley Page slotted wings to German airplanes. Comparitive gliding tests were made with open and closed slots on an Albatros L 75 airplane equipped with the Handley Page "auto control slots." This investigation served to determine the effect of the auto control slot on the properties and performances of airplanes at large angles of attack. The most important problems were whether the angle of glide at small angles of attack can be increased by the adoption of the auto control slot and, in particular, as to whether the flight characteristics at large angles of attack are improved thereby and equilibrium in gliding flight is guaranteed even at larger than ordinary angles of attack.

Practical Tests with the "auto Control Slot." Part I : Lecture

NASA Technical Reports Server (NTRS)

Lachmann, G

1930-01-01

For some time the D.V.L. has been investigating the question of applicability of Handley Page slotted wings to German airplanes. Comparitive gliding tests were made with open and closed slots on an Albatros L 75 airplane equipped with the Handley Page "auto control slots." This investigation served to determine the effect of the auto control slot on the properties and performances of airplanes at large angles of attack. The most important problems were whether the angle of glide at small angles of attack can be increased by the adoption of the auto control slot and, in particular, as to whether the flight characteristics at large angles of attack are improved thereby and equilibrium in gliding flight is guaranteed even at larger than ordinary angles of attack.

Large-Eddy Simulation of the Base Flow of a Cylindrical Space Vehicle Configuration

NASA Astrophysics Data System (ADS)

Meiß, J.-H.; Schröder, W.

2009-01-01

A Large-Eddy Simulation (LES) is performed out to in- vestigate high Reynolds number base flow of an axisymmetric rocket-like configuration having an underex- panded nozzle flow. The subsonic base region of low pressure levels is characterized and bounded by the interaction of the freestream of Mach 5.3 and the wide plume of the hot exhaust jet of Mach 3.8. An analysis of the base flow shows that the system of base area vortices determines the highly time-dependent pressure distribution and causes an upstream convection of hot exhaust gas. A comparison of the results with experiments conducted at the German Aerospace Center (DLR) Cologne shows good agreement. The investigation is part of the German RESPACE Pro- gram, which focuses on Key Technologies for Reusable Space Systems.

Climate Dynamics and Hysteresis at Low and High Obliquity

NASA Astrophysics Data System (ADS)

Colose, C.; Del Genio, A. D.; Way, M.

2017-12-01

We explore the large-scale climate dynamics at low and high obliquity for an Earth-like planet using the ROCKE-3D (Resolving Orbital and Climate Keys of Earth and Extraterrestrial Environments with Dynamics) 3-D General Circulation model being developed at NASA GISS as part of the Nexus for Exoplanet System Science (NExSS) initiative. We highlight the role of ocean heat storage and transport in determining the seasonal cycle at high obliquity, and describe the large-scale circulation and resulting regional climate patterns using both aquaplanet and Earth topographical boundary conditions. Finally, we contrast the hysteresis structure to varying CO2 concentration for a low and high obliquity planet near the outer edge of the habitable zone. We discuss the prospects for habitability for a high obliquity planet susceptible to global glaciation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perry, F.V.; Valentine, G.A.; Crowe, B.M.

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The objective of this project was to determine whether isotopic techniques can be used to assess the eruption potential and eruption volume of continental stratovolcanoes. Large-volume eruptions from stratovolcanoes pose significant hazards to population and infrastructure in many parts of the world. We are testing whether this technique will allow a short- to medium-term (decades to millennia) probabilistic hazard assessment of large-volume eruptions. If successful, the technique will be useful to countries or regions that must consider medium tomore » long-term volcanic (e.g., nuclear waste facilities). We have begun sample acquisition and isotopic measurements at two stratovolcanoes, Pico de Orizaba in eastern Mexico and Daisen in western Japan.« less

Materials Characterisation and Analysis for Flow Simulation of Liquid Resin Infusion

NASA Astrophysics Data System (ADS)

Sirtautas, J.; Pickett, A. K.; George, A.

2015-06-01

Liquid Resin Infusion (LRI) processes including VARI and VARTM have received increasing attention in recent years, particularly for infusion of large parts, or for low volume production. This method avoids the need for costly matched metal tooling as used in Resin Transfer Moulding (RTM) and can provide fast infusion if used in combination with flow media. Full material characterisation for LRI analysis requires models for three dimensional fabric permeability as a function of fibre volume content, fabric through-thickness compliance as a function of resin pressure, flow media permeability and resin viscosity. The characterisation of fabric relaxation during infusion is usually determined from cyclic compaction tests on saturated fabrics. This work presents an alternative method to determine the compressibility by using LRI flow simulation and fitting a model to experimental thickness measurements during LRI. The flow media is usually assumed to have isotropic permeability, but this work shows greater simulation accuracy from combining the flow media with separation plies as a combined orthotropic material. The permeability of this combined media can also be determined by fitting the model with simulation to LRI flow measurements. The constitutive models and the finite element solution were validated by simulation of the infusion of a complex aerospace demonstrator part.

Competition from below for light and nutrients shifts productivity among tropical species.

PubMed

Ewel, John J; Mazzarino, María Julia

2008-12-02

Chance events such as seed dispersal determine the potential composition of plant communities, but the eventual assemblage is determined in large part by subsequent interactions among species. Postcolonization sorting also affects the ultimate composition of communities assembled by people for restoration, horticulture, or conservation. Thus, knowledge of the mechanisms controlling interspecific interactions in plant communities is important for explaining patterns observed in nature and predicting success or failure of utilitarian combinations. Relationships among species, especially those from studies of biological diversity and ecosystem functioning, are largely based on studies of short-lived, temperate-zone plants. Extrapolation to perennial plants in the humid tropics is risky because functional relationships among large-stature species change with time. Shifts in competitive relationships among 3 life forms--trees, palms, and perennial herbs--occurred during 13 yr in experimental tropical ecosystems. In 2 cases the novel competitive mechanism responsible for the shift was reduction in crown volume, and therefore light-capturing capability, of overtopping deciduous trees by intrusive growth from below a palm. In a third case, complementary resource use developed between 2 evergreen life forms (overstory tree and palm), probably because of differential nutrient acquisition. Species-level traits and adequate time for shifts in interspecific relationships to emerge are crucial for predicting community trajectories.

Calculations concerning the HCO(+)/HOC(+) abundance ratio in dense interstellar clouds

NASA Technical Reports Server (NTRS)

Defrees, D. J.; Mclean, A. D.; Herbst, E.

1984-01-01

Calculations have been performed to determine the rate coefficients of several reactions involved in both the formation and depletion of interstellar HCO(+) and HOC(+). The abundance of HOC(+) deduced from these calculations is consistent with the tentative identification of HOC(+) in Sgr B2 by Woods et al. (1983). The large HCO(+)/HOC(+) abundance ratio observed by Woods et al. is due at least in part to a more rapid formation rate for HCO(+) and probably due as well to a more rapid depletion rate for HOC(+).

Management of post burn hand deformities

PubMed Central

Sabapathy, S. Raja; Bajantri, Babu; Bharathi, R. Ravindra

2010-01-01

The hand is ranked among the three most frequent sites of burns scar contracture deformity. One of the major determinants of the quality of life in burns survivors is the functionality of the hands. Burns deformities, although largely preventable, nevertheless do occur when appropriate treatment is not provided in the acute situation or when they are part of a major burns. Reconstructive procedures can greatly improve the function of the hands. Appropriate choice of procedures and timing of surgery followed by supervised physiotherapy can be a boon for a burns survivor. PMID:21321661

APXS on Mars: Analyses of Soils and Rocks at Gusev Crater and Meridiani Planum

NASA Technical Reports Server (NTRS)

Rieder, R.; Gellert, R.; Brueckner, J.; Clark, B. C.; Dreibus, G.; dUston, C.; Economou, T.; Klingelhoefer, G.; Lugmair, G. W.; Waenke, H.

2004-01-01

Newly developed APXS (Alpha Particle X-Ray Spectrometers) are part of the Athena payload of the Mars Exploration Rovers Spirit and Opportunity [1]. The APXS determines the chemical composition of soils and rocks along the traverse of the two rovers. Spirit and Opportunity operate at Gusev Crater and Meridiani Planum, respectively. First results of soil X-ray spectra at both landing sites support the hypothesis of a global homogenization of the soil by large dust storms and impact processes in the northern and southern hemisphere.

A statistical formulation of one-dimensional electron fluid turbulence

NASA Technical Reports Server (NTRS)

Fyfe, D.; Montgomery, D.

1977-01-01

A one-dimensional electron fluid model is investigated using the mathematical methods of modern fluid turbulence theory. Non-dissipative equilibrium canonical distributions are determined in a phase space whose co-ordinates are the real and imaginary parts of the Fourier coefficients for the field variables. Spectral densities are calculated, yielding a wavenumber electric field energy spectrum proportional to k to the negative second power for large wavenumbers. The equations of motion are numerically integrated and the resulting spectra are found to compare well with the theoretical predictions.

Geologic structure and altitude of the top of the Minnelusa Formation, northern Black Hills, South Dakota and Wyoming, and Bear Lodge Mountains, Wyoming

USGS Publications Warehouse

Peter, Kathy D.; Kyllonen, David P.; Mills, K.R.

1987-01-01

Beginning in 1981, a 3-yr project was conducted to determine the availability and quality of groundwater in the sedimentary bedrock aquifers in the Black Hills of South Dakota and Wyoming. The project was limited to three bedrock units in order of increasing age: the Cretaceous Inyan kara Group, Permian and Pennsylvanian Minnelusa Formation, and Mississippian Madison (or Pahasapa) Limestone. This map shows the altitude of the top of the Minnelusa Formation in the northern Black Hills, and shows the configuration of the structural features in the northern part of the Black Hills and the eastern part of the Bear Lodge Mountains. In general, the Minnelusa Formation dips away from the Black Hills uplift, either to the northeast and the Williston Basin or, south of the Bear Lodge Mountains, to the southwest and the Powder River basin, which is outside the map area. In the map area, the upper beds of the Minnelusa Formation are an aquifer and the lower beds are a confining or semi-confining unit. The upper part of the Minnelusa Formation has a greater percentage of coarse-grained sandstone beds than the lower part. Furthermore, solution and removal of anhydrite, brecciation, and solution of cement binding the sandstone grains may have increased the permeability of the upper part of the Minnelusa Formation in the Black Hills. Wells completed in the upper part of the Minnelusa have yields that exceed 100 gal/min in some areas and at least one large diameter well is reported to flow 1,000 gal/min in some areas and at least one large diameter well is reported to flow 1,000 gal/min. Flowing wells have been completed in the Minnelusa aquifer in most of the study area in South Dakota and in about the northern one-half of Crook County, Wyoming. (Lantz-PTT)

Paternal age at birth is an important determinant of offspring telomere length.

PubMed

De Meyer, Tim; Rietzschel, Ernst R; De Buyzere, Marc L; De Bacquer, Dirk; Van Criekinge, Wim; De Backer, Guy G; Gillebert, Thierry C; Van Oostveldt, Patrick; Bekaert, Sofie

2007-12-15

Although evidence supports the function of telomere length (TL) as a marker for biological aging, no major determinants of TL are known besides inheritance, age and gender. Here we validate and, more importantly, assess the impact of paternal age at birth as a determinant for the offspring's peripheral blood leukocyte TL within the Asklepios study population. Telomere restriction fragment length and paternal age information were available for 2433 volunteers (1176 men and 1257 women) aged approximately 35-55 years old. Paternal age at birth was positively associated with offspring TL (offspring age and gender adjusted, P < 10 (-14)). The increase in TL was estimated at 17 base pairs for each supplemental year at birth and was not statistically different between male and female offspring. The effect size of paternal age outweighed the classical TL determinant gender by a factor of 2, demonstrating the large impact. Maternal age at birth was not independently associated with offspring TL. The peculiar interaction between paternal age at birth and inheritance might explain a large part of the genetic component of TL variance on a population level. This finding also provides further proof for the theory that TL is not completely reset in the zygote. Furthermore, as paternal age is subject to demographic evolution, its association with TL might have a substantial impact on the results and comparability of TL within and between epidemiological studies. In conclusion, paternal age is an important determinant for TL, with substantial consequences for future studies.

Apollo 16 view of the earth from translunar injection

NASA Technical Reports Server (NTRS)

1972-01-01

A good view of the Earth photographed shortly after translunar injection of April 16, 1972. Although there is much cloud cover (over Canada and the oceans), the United States in large part, most of Mexico and some parts of Central America are clearly visible. Note Lake Michigan and Lake Superior. Also note the Bahama Banks at upper right part of the sphere. A large part of the Rocky Mountain Range is also visible.

a Microgravity Survey to Determine the Extent of AN Andesitic Sill that Intrudes across the Rio Grande River Basin, Rio Grande Rift Valley, Sunland Park, New Mexico

NASA Astrophysics Data System (ADS)

Baker, L. A.; Shinagel, S.; Villalobos, J. I.; Avila, V.; Montana, C. J.; Kaip, G.

2012-12-01

In Sunland Park, NM, there is an andesite outcrop near the bank of the Rio Grande (called the River Andesite) which does not match the surrounding sedimentary deposition. Studies of the River Andesite by Garcia (1970) indicate the outcrop is petrologically similar to the Muleros Andesite of Mt. Cristo Rey located several km to the south. A limited GPR and magnetic survey conducted by UTEP students in 2008 suggested the River Andesite was part of a dike, although Garcia mapped smaller outcrops of andesite ~300 m west of the river that may be part of the same body. We have recently (June 2012) found large andesite boulders that may be the outcrops Garcia mapped, although it is uncertain whether these boulders are in-situ. We initially collected microgravity and magnetic data in a small region near the river outcrop in December 2011 to determine the extent of the outcrop. Our preliminary modeling of these data showed the river outcrop appeared to merge with a more extensive igneous body at depth. Ground conductivity data collected near the river outcrop in March 2012 suggested that the outcrop impacts groundwater flow and sediment deposition adjacent to the river. From May through July 2012 we have been collecting additional microgravity data on a grid with 100-200 m spacing extending ~ 500 m from both sides of the river outcrop to better determine the extent of the buried andesite body. We also plan to conduct GPR and magnetic surveys near the recently discovered andesite boulders to determine if these are truly in-situ and part of the same igneous body as the river outcrop. Our eventual goal is to determine how extensive the andesite unit is and how it may impact groundwater flow and flooding in this area of growing urbanization.

Concurrent and Overlapping Surgery: Perspectives from Parents of Adolescents Undergoing Spinal Posterior Instrumented Fusion for Idiopathic Scoliosis.

PubMed

Bryant, Jessica; Markes, Alexander; Woolridge, Tiana; Cerruti, Dede; Dzeng, Elizabeth; Koenig, Barbara; Diab, Mohammad

2018-06-12

Prospective cross-sectional survey. To determine the perspectives of parents of patients undergoing posterior instrumented fusion for adolescent idiopathic scoliosis (AIS) regarding simultaneous surgery and trainee participation. Simultaneous ("at the same time") surgery is under scrutiny by the public, government, payers and the medical community. The objective of this study is to determine the perspectives of parents of patients undergoing posterior instrumented fusion for adolescent idiopathic scoliosis. Our goal is to inform the national conversation on this subject with real patient and family voices. A survey was prospectively administered to 31 consecutive parents of patients undergoing posterior instrumented fusion for adolescent idiopathic scoliosis at a large academic medical center. "Overlapping" was defined as simultaneity during "noncritical" parts of an operation. "Concurrent" was defined as simultaneity that includes "critical" part(s) of an operation. Participants were asked to provide levels of agreement with overlapping and concurrent surgery and anesthesia, as well as with trainee involvement. On average, respondents "strongly agree" with the need to be informed about overlapping or concurrent surgery. They "disagree" with both overlapping and concurrent scheduling, and "disagree" with trainees operating without direct supervision, even for "non-critical" parts. Informing parents about the presence of a back-up surgeon or research demonstrating safety of simultaneous surgery did not make them agreeable to simultaneous scheduling. Parents have a strong desire to be informed of simultaneous spinal surgery as part of consent on behalf of their children. Their disagreement with simultaneous surgery, as well as with trainees operating without direct supervision, suggests discordance with current guidelines and practice and should inform the national conversation moving forward. N/A.

Investigation into stutter ratio variability between different laboratories.

PubMed

Bright, Jo-Anne; Curran, James M

2014-11-01

The determination of parameters such as stutter ratio is important to inform a laboratory's forensic DNA profile interpretation strategy. As part of a large data analysis project to implement a continuous model of DNA profile interpretation we analysed stutter ratio data from eight different forensic laboratories for the Promega PowerPlex(®) 21 multiplex. This allowed a comparison of inter laboratory variation. The maximum difference for any one laboratory from the average of the best fit determined by the model was 0.31%. These results indicate that stutter ratios calculated from samples analysed using the same profiling kit are not expected to differ between laboratories, even those using different capillary electrophoresis platforms. A common set of laboratory parameters are able to be generated and used for profile interpretation at all laboratories using the same multiplex and cycle number, potentially reducing the need for individual laboratories to determine stutter ratios. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Determination of the muon charge sign with the dipolar spectrometers of the OPERA experiment

NASA Astrophysics Data System (ADS)

Agafonova, N.; Aleksandrov, A.; Anokhina, A.; Aoki, S.; Ariga, A.; Ariga, T.; Bender, D.; Bertolin, A.; Bozza, C.; Brugnera, R.; Buonaura, A.; Buontempo, S.; Büttner, B.; Chernyavsky, M.; Chukanov, A.; Consiglio, L.; D'Ambrosio, N.; De Lellis, G.; De Serio, M.; Del Amo Sanchez, P.; Di Crescenzo, A.; Di Ferdinando, D.; Di Marco, N.; Dmitrievski, S.; Dracos, M.; Duchesneau, D.; Dusini, S.; Dzhatdoev, T.; Ebert, J.; Ereditato, A.; Fini, R. A.; Fukuda, T.; Galati, G.; Garfagnini, A.; Giacomelli, G.; Göllnitz, C.; Goldberg, J.; Goloubkov, D.; Gornushkin, Y.; Grella, G.; Guler, M.; Gustavino, C.; Hagner, C.; Hara, T.; Hollnagel, A.; Hosseini, B.; Ishida, H.; Ishiguro, K.; Jakovcic, K.; Jollet, C.; Kamiscioglu, C.; Kamiscioglu, M.; Kawada, J.; Kim, J. H.; Kim, S. H.; Kitagawa, N.; Klicek, B.; Kodama, K.; Komatsu, M.; Kose, U.; Kreslo, I.; Lauria, A.; Lenkeit, J.; Ljubicic, A.; Longhin, A.; Loverre, P.; Malgin, A.; Malenica, M.; Mandrioli, G.; Matsuo, T.; Matveev, V.; Mauri, N.; Medinaceli, E.; Meregaglia, A.; Meyer, M.; Mikado, S.; Monacelli, P.; Montesi, M. C.; Morishima, K.; Muciaccia, M. T.; Naganawa, N.; Naka, T.; Nakamura, M.; Nakano, T.; Nakatsuka, Y.; Niwa, K.; Ogawa, S.; Okateva, N.; Olshevsky, A.; Omura, T.; Ozaki, K.; Paoloni, A.; Park, B. D.; Park, I. G.; Pasqualini, L.; Pastore, A.; Patrizii, L.; Pessard, H.; Pistillo, C.; Podgrudkov, D.; Polukhina, N.; Pozzato, M.; Pupilli, F.; Roda, M.; Rokujo, H.; Roganova, T.; Rosa, G.; Rostovtseva, I.; Ryazhskaya, O.; Sato, O.; Sato, Y.; Schembri, A.; Shakiryanova, I.; Shchedrina, T.; Sheshukov, A.; Shibuya, H.; Shiraishi, T.; Shoziyoev, G.; Simone, S.; Sioli, M.; Sirignano, C.; Sirri, G.; Spinetti, M.; Stanco, L.; Starkov, N.; Stellacci, S. M.; Stipcevic, M.; Strolin, P.; Takahashi, S.; Tenti, M.; Terranova, F.; Tioukov, V.; Tufanli, S.; Vilain, P.; Vladimirov, M.; Votano, L.; Vuilleumier, J. L.; Wilquet, G.; Wonsak, B.; Yoon, C. S.; Zaitsev, Y.; Zemskova, S.; Zghiche, A.

2016-07-01

The OPERA long-baseline neutrino-oscillation experiment has observed the direct appearance of ντ in the CNGS νμ beam. Two large muon magnetic spectrometers are used to identify muons produced in the τ leptonic decay and in νμ CC interactions by measuring their charge and momentum. Besides the kinematic analysis of the τ decays, background resulting from the decay of charmed particles produced in νμ CC interactions is reduced by efficiently identifying the muon track. A new method for the charge sign determination has been applied, via a weighted angular matching of the straight track-segments reconstructed in the different parts of the dipole magnets. Results obtained for Monte Carlo and real data are presented. Comparison with a method where no matching is used shows a significant reduction of up to 40% of the fraction of wrongly determined charges.

Evidence for hydrodynamic electron flow in PdCoO₂.

PubMed

Moll, Philip J W; Kushwaha, Pallavi; Nandi, Nabhanila; Schmidt, Burkhard; Mackenzie, Andrew P

2016-03-04

Electron transport is conventionally determined by the momentum-relaxing scattering of electrons by the host solid and its excitations. Hydrodynamic fluid flow through channels, in contrast, is determined partly by the viscosity of the fluid, which is governed by momentum-conserving internal collisions. A long-standing question in the physics of solids has been whether the viscosity of the electron fluid plays an observable role in determining the resistance. We report experimental evidence that the resistance of restricted channels of the ultrapure two-dimensional metal palladium cobaltate (PdCoO2) has a large viscous contribution. Comparison with theory allows an estimate of the electronic viscosity in the range between 6 × 10(-3) kg m(-1) s(-1) and 3 × 10(-4) kg m(-1) s(-1), versus 1 × 10(-3) kg m(-1) s(-1) for water at room temperature. Copyright © 2016, American Association for the Advancement of Science.

Droplets on bent fibers

NASA Astrophysics Data System (ADS)

Weyer, Floriane; Pan, Zhao; Pitt, William; Truscott, Tadd; Vandewalle, Nicolas

Droplets on fibers are part of our everyday lives. Many phenomena involve drops and fibers such as the formation of dew droplets on a spiderweb, the trapping of water droplets on cactus spines or the motion of droplets on wetted moss hairs. These topics have been widely studied. In particular, Lorenceau et al. determined the critical volume of a water droplet hanging on a horizontal fiber. Here, we address a similar question : we try to find out the maximum droplet size on bent fibers, which are able to hold significantly more water than horizontal fibers. Indeed, we noticed that, in nature, some specific plants can hold large rain droplets thanks to their Y-shaped leaves. We try to mimic these structures with nylon fibers, of different diameters, bent with various angles. For each set-up, the critical water volume is determined. Finally, we propose models of the physics involved in determining droplet size that could be implemented in future fiber-based microfluidic devices.

BOOK REVIEW: Analysis of Residual Stress by Diffraction Using Neutron and Synchrotron Radiation

NASA Astrophysics Data System (ADS)

Fitzpatrick, ed M. E.; Lodini, A.

2003-09-01

The presence of residual stresses within engineering components is often a key feature in determining their usable lifetimes and failure characteristics. Residual surface compression can, for example, restrict the propagation of surface cracks through the bulk. As a consequence, it is essential to characterize the magnitude and spatial distribution of residual stresses and, at least for non-destructive testing, this is most widely achieved using diffraction of neutron and high energy synchrotron radiations. This book aims to provide a detailed description of the methodology used to determine residual stresses. The major emphasis is placed on the neutron method, this being the more widely established approach at present. It contains 20 chapters contributed by 23 authors, divided into five major parts. The overall layout is very logical, with the first part giving a general introduction to the use of neutrons and x-rays for materials research and summarizing the methods used for their production. Part 2 considers the more specific aspects of extracting the residual stress distribution within a bulk sample and includes some valuable comments on a number of potential experimental problems, such as the determination of the stress-free lattice parameter and the effects of broadening of the Bragg peaks. The experimental facilities currently available or under development are described in part 3, with the remaining two parts devoted to general and specific applications of the residual stress measurement technique. As expected with such a large number of different authors, there is some variation in style and quality. However, the text is generally easy to follow and, more importantly, it is largely free of the problems of inconsistent notation and dupication of material that can afflict multi-authored texts. My only negative comment concerns the latter portion of the book devoted to specific applications of the technique, which is illustrative rather than comprehensive. In particular, there is no clear justification for the particular choice of topics included. Chapters devoted to the more important areas of residual stresses in aerospace components and within the chemical industry would probably have more general interest than, for example, the one devoted nuclear fusion reactors. The publication of this book is rather timely, with a current expansion in the experimental facilities available for the measurement of residual stresses, including dedicated diffractometers for the study of engineering components. To the best of my knowledge, there is no comparable text currently available. In my opinion, this book provides both an accessible introduction to the topic for new students in this particular area and a useful reference text on the current status of the field to more established researchers. Stephen Hull

Sequential Determination of U and Th Decay Series in Santana Cave, Southwest Brazil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silva, P. S. C.; Damatto, S. R.; Mazzilli, B. P.

2008-08-07

Parque Estadual Turistico do Alto Ribeira (PETAR) is located in the South-western part of Sao Paulo State, in the Ribeira Valley. In this national state park a large number of caves are found, which are among the most visited of the country. These caves, located in a karstic zone, are characterized by the presence of carbonaceous rocks frequently fractured and collapsed. Although, carbonates (dolomites and calcitic rocks) usually have low U content, this element can be found in the structure of the surrounding rocks. This paper aims to determine {sup 238}U, {sup 234}U, {sup 226}Ra and {sup 210}Pb concentration inmore » samples of rock, soil, river water and sediment, in Santana cave. The radionuclide {sup 238}U was determined by alpha spectrometry using a surface barrier detector. {sup 226}Ra and {sup 210}Pb were determined by measuring the gross alpha and beta activity on a gas flow proportional counter.« less

Multistrategy learning: A case study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Domingos, P.

1996-12-31

Two of the most popular approaches to induction are instance-based learning (IBL) and rule generation. Their strengths and weaknesses are largely complementary. IBL methods are able to identify small details in the instance space, but have trouble with attributes that are relevant in some parts of the space but not others. Conversely, rule induction methods may overlook small exception regions, but are able to select different attributes in different parts of the instance space. The two methods have been unified in the RISE algorithm. RISE views instances as maximally specific rules, forms more general rules by gradually clustering instances ofmore » the same class, and classifies a test example by letting the nearest rule win. This approach potentially combines the advantages of rule induction and IBL, and has indeed been observed to be more accurate than each on a large number of bench-mark datasets. However, it is important to determine if this performance is indeed due to the hypothesized advantages, and to define the situations in which RISE`s bias will and will not be preferable to those of the individual approaches. This abstract reports experiments to this end in artificial domains.« less

Interaction between dietary protein content and the source of carbohydrates along the gastrointestinal tract of weaned piglets.

PubMed

Pieper, Robert; Boudry, Christelle; Bindelle, Jérôme; Vahjen, Wilfried; Zentek, Jürgen

2014-01-01

Although fermentable carbohydrates (CHO) can reduce metabolites derived from dietary protein fermentation in the intestine of pigs, the interaction between site of fermentation and substrate availability along the gut is still unclear. The current study aimed at determining the impact of two different sources of carbohydrates in diets with low or very high protein content on microbial metabolite profiles along the gastrointestinal tract of piglets. Thirty-six piglets (n = 6 per group) were fed diets high (26%, HP) or low (18%, LP) in dietary protein and with or without two different sources of carbohydrates (12% sugar beet pulp, SBP, or 8% lignocellulose, LNC) in a 2 × 3 factorial design. After 3 weeks, contents from stomach, jejunum, ileum, caecum, proximal and distal colon were taken and analysed for major bacterial metabolites (D-lactate, L-lactate, short chain fatty acids, ammonia, amines, phenols and indols). Results indicate considerable fermentation of CHO and protein already in the stomach. HP diets increased the formation of ammonia, amines, phenolic and indolic compounds throughout the different parts of the intestine with most pronounced effects in the distal colon. Dietary SBP inclusion in LP diets favoured the formation of cadaverine in the proximal parts of the intestine. SBP mainly increased CHO-derived metabolites such as SCFA and lactate and decreased protein-derived metabolites in the large intestine. Based on metabolite profiles, LNC was partly fermented in the distal large intestine and reduced mainly phenols, indols and cadaverine, but not ammonia. Multivariate analysis confirmed more diet-specific metabolite patterns in the stomach, whereas the CHO addition was the main determinant in the caecum and proximal colon. The protein level mainly influenced the metabolite patterns in the distal colon. The results confirm the importance of CHO source to influence the formation of metabolites derived from protein fermentation along the intestinal tract of the pig.

Size and structure of Chlorella zofingiensis /FeCl 3 flocs in a shear flow: Algae Floc Structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wyatt, Nicholas B.; O'Hern, Timothy J.; Shelden, Bion

Flocculation is a promising method to overcome the economic hurdle to separation of algae from its growth medium in large scale operations. But, understanding of the floc structure and the effects of shear on the floc structure are crucial to the large scale implementation of this technique. The floc structure is important because it determines, in large part, the density and settling behavior of the algae. Freshwater algae floc size distributions and fractal dimensions are presented as a function of applied shear rate in a Couette cell using ferric chloride as a flocculant. Comparisons are made with measurements made formore » a polystyrene microparticle model system taken here as well as reported literature results. The algae floc size distributions are found to be self-preserving with respect to shear rate, consistent with literature data for polystyrene. Moreover, three fractal dimensions are calculated which quantitatively characterize the complexity of the floc structure. Low shear rates result in large, relatively dense packed flocs which elongate and fracture as the shear rate is increased. Our results presented here provide crucial information for economically implementing flocculation as a large scale algae harvesting strategy.« less

The determination of ionospheric electron content and distribution from satellite observations. Part 2. Results of the analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garriott, O K

1960-04-01

The results of observations of the radio transmissions from Sputnik III (1958 δ 2) in an 8-month period are presented. The measurements of integrated electron density are made in two ways, described in part 1. The measurements reveal the diurnal variation of the total ionospheric electron content; and the ratio of the total content to the content of the lower ionosphere below the height of maximum density in the F layer is obtained. An estimate of the average electron-density profile above the F-layer peak is made possible by the slow variation in the height of the satellite due to rotationmore » of the perigee position. The gross effects of large magnetic storms on the electron content and distribution are found.« less

19 CFR Appendix C to Part 113 - Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows

Code of Federal Regulations, 2011 CFR

2011-04-01

... 19 Customs Duties 1 2011-04-01 2011-04-01 false Bond for Deferral of Duty on Large Yachts Imported... Appendix C to Part 113—Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows ____, as...

19 CFR Appendix C to Part 113 - Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Bond for Deferral of Duty on Large Yachts Imported... Appendix C to Part 113—Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows Bond for Deferral of Duty on Large Yachts Imported for Sale at United States Boat Shows ____, as...

Handling missing values in the MDS-UPDRS.

PubMed

Goetz, Christopher G; Luo, Sheng; Wang, Lu; Tilley, Barbara C; LaPelle, Nancy R; Stebbins, Glenn T

2015-10-01

This study was undertaken to define the number of missing values permissible to render valid total scores for each Movement Disorder Society Unified Parkinson's Disease Rating Scale (MDS-UPDRS) part. To handle missing values, imputation strategies serve as guidelines to reject an incomplete rating or create a surrogate score. We tested a rigorous, scale-specific, data-based approach to handling missing values for the MDS-UPDRS. From two large MDS-UPDRS datasets, we sequentially deleted item scores, either consistently (same items) or randomly (different items) across all subjects. Lin's Concordance Correlation Coefficient (CCC) compared scores calculated without missing values with prorated scores based on sequentially increasing missing values. The maximal number of missing values retaining a CCC greater than 0.95 determined the threshold for rendering a valid prorated score. A second confirmatory sample was selected from the MDS-UPDRS international translation program. To provide valid part scores applicable across all Hoehn and Yahr (H&Y) stages when the same items are consistently missing, one missing item from Part I, one from Part II, three from Part III, but none from Part IV can be allowed. To provide valid part scores applicable across all H&Y stages when random item entries are missing, one missing item from Part I, two from Part II, seven from Part III, but none from Part IV can be allowed. All cutoff values were confirmed in the validation sample. These analyses are useful for constructing valid surrogate part scores for MDS-UPDRS when missing items fall within the identified threshold and give scientific justification for rejecting partially completed ratings that fall below the threshold. © 2015 International Parkinson and Movement Disorder Society.

Comparison of microbial populations in the small intestine, large intestine and feces of healthy horses using terminal restriction fragment length polymorphism

PubMed Central

2013-01-01

Background The composition of the microbiota of the equine intestinal tract is complex. Determining whether the microbial composition of fecal samples is representative of proximal compartments of the digestive tract could greatly simplify future studies. The objectives of this study were to compare the microbial populations of the duodenum, ileum, cecum, colon and rectum (feces) within and between healthy horses, and to determine whether rectal (fecal) samples are representative of proximal segments of the gastrointestinal tract. Intestinal samples were collected from ten euthanized horses. 16S rRNA gene PCR-based TRFLP was used to investigate microbiota richness in various segments of the gastrointestinal tract, and dice similarity indices were calculated to compare the samples. Results Within horses large variations of microbial populations along the gastrointestinal tract were seen. The microbiota in rectal samples was only partially representative of other intestinal compartments. The highest similarity was obtained when feces were compared to the cecum. Large compartmental variations were also seen when microbial populations were compared between six horses with similar dietary and housing management. Conclusion Rectal samples were not entirely representative of intestinal compartments in the small or large intestine. This should be taken into account when designing studies using fecal sampling to assess other intestinal compartments. Similarity between horses with similar dietary and husbandry management was also limited, suggesting that parts of the intestinal microbiota were unique to each animal in this study. PMID:23497580

Map showing the thickness of loosely packed sediments and the depth to bedrock in the Sugar House quadrangle, Salt Lake County, Utah

USGS Publications Warehouse

McGregor, Edward E.; Van Horn, Richard; Arnow, Ted

1974-01-01

This map provides information on the location and distribution of three general types of geologic materials in part of Salt Lake County, including the southeastern part of Salt Lake City, Utah. These materials have different physical properties that are pertinent to comprehensive planning and zoning, land-use studies, and engineering usage. The map should be of use in preliminary studies to determine the depth to different  general types of foundation material and to determine the potential for settlement of the ground surface during major earthquakes, which could result in damage to waterlines, gaslines, large buildings, and other major engineering structures.The lines on the map are generalized. Lines showing the thickness of loosely packed sediments are based on drillers’ logs of 27 water wells in and near the 35-square-mile part of the quadrangle west of the mountains – less than one data point for each square mile. Lines showing the depth to bedrock are based on indirect geophysical data, and the data points are more widely scattered. The map may be useful as a general guide in planning, but investigations by qualified specialists should be made for detailed evaluations of specific areas.references to other reports of possible interest to the reader are included at the end of this text.

Spectral radiative properties of a living human body

NASA Astrophysics Data System (ADS)

Terada, N.; Ohnishi, K.; Kobayashi, M.; Kunitomo, T.

1986-09-01

Spectral radiative properties of the human body were studied experimentally in the region from the ultraviolet to the far-infrared to know the thermal response of the human body exposed to solar radiation and infrared radiation. The measuring equipment for reflectance and transmittance of a semitransparent scattering medium was developed and measurement on a living human skin was performed in vivo. The measured parts are forearm, cheek, dorsum hand, hip, and hair. The values obtained by the present study are much different from those of previous in vitro measurements. Fairly large values for hemispherical reflectances are observed in the visible and near-infrared regions but very small values for hemispherical reflectances are observed in the infrared region, below 0.05. By applying the four-flux treatment of radiative transfer, the absorption coefficient and scattering coefficient in the human skin are determined. The scattering coefficient is large in the visible region but negligible in the infrared region. The absorption coefficient is very close to that of water and large in the infrared region.

Human antibody fragments specific for the epidermal growth factor receptor selected from large non-immunised phage display libraries.

PubMed

Souriau, Christelle; Rothacker, Julie; Hoogenboom, Hennie R; Nice, Edouard

2004-09-01

Antibodies to EGFR have been shown to display anti-tumour effects mediated in part by inhibition of cellular proliferation and angiogenesis, and by enhancement of apoptosis. Humanised antibodies are preferred for clinical use to reduce complications with HAMA and HAHA responses frequently seen with murine and chimaeric antibodies. We have used depletion and subtractive selection strategies on cells expressing the EGFR to sample two large antibody fragment phage display libraries for the presence of human antibodies which are specific for the EGFR. Four Fab fragments and six scFv fragments were identified, with affinities of up to 2.2nM as determined by BIAcore analysis using global fitting of the binding curves to obtain the individual rate constants (ka and kd). This overall approach offers a generic screening method for the identification of growth factor specific antibodies and antibody fragments from large expression libraries and has potential for the rapid development of new therapeutic and diagnostic reagents.

Mineral resource assessment of the Dillon 1 degree x 2 degrees Quadrangle, Idaho and Montana

USGS Publications Warehouse

Pearson, Robert Carl; Trautwein, C.M.; Ruppel, E.T.; Hanna, W.F.; Rowan, L.C.; Loen, J.S.; Berger, B.R.

1992-01-01

The Dillon 1°x2° quadrangle in southwestern Montana and east-central Idaho was investigated as part of the U.S. Geological Survey's Conterminous United States Mineral Assessment Program (CUSMAP) to determine its mineral resource potential. An interdisciplinary study was made of geology, geochemistry, geophysics (gravity and aeromagnetics), remote sensing, and mineral deposits. The results of those studies, as well as mineral resource assessment of numerous mineraldeposit types, are published separately as a folio of maps. This report summarizes the studies, provides background information on them, and presents a selected bibliography relevant to the geology and mineral resources of the quadrangle. The quadrangle contains large resources of gold and substantial resources of talc and chlorite, all of which were being mined in the 1980's and early 1990's. Submarginal resources of molybdenum, copper, tungsten, and iron range from moderately large to large. Other commodities that may be present in significant amounts are chromite, lead, zinc, silver, barite, zeolite minerals, and various nonmetallic metamorphic minerals.

Two Rounds of Whole Genome Duplication in the Ancestral Vertebrate

PubMed Central

Dehal, Paramvir; Boore, Jeffrey L

2005-01-01

The hypothesis that the relatively large and complex vertebrate genome was created by two ancient, whole genome duplications has been hotly debated, but remains unresolved. We reconstructed the evolutionary relationships of all gene families from the complete gene sets of a tunicate, fish, mouse, and human, and then determined when each gene duplicated relative to the evolutionary tree of the organisms. We confirmed the results of earlier studies that there remains little signal of these events in numbers of duplicated genes, gene tree topology, or the number of genes per multigene family. However, when we plotted the genomic map positions of only the subset of paralogous genes that were duplicated prior to the fish–tetrapod split, their global physical organization provides unmistakable evidence of two distinct genome duplication events early in vertebrate evolution indicated by clear patterns of four-way paralogous regions covering a large part of the human genome. Our results highlight the potential for these large-scale genomic events to have driven the evolutionary success of the vertebrate lineage. PMID:16128622

Effect size for the main cognitive function determinants in a large cross-sectional study.

PubMed

Mura, T; Amieva, H; Goldberg, M; Dartigues, J-F; Ankri, J; Zins, M; Berr, C

2016-11-01

The aim of our study was to examine the effect sizes of different cognitive function determinants in middle and early old age. Cognitive functions were assessed in 11 711 volunteers (45 to 75 years old), included in the French CONSTANCES cohort between January 2012 and May 2014, using the free and cued selective reminding test (FCSRT), verbal fluency tasks, digit-symbol substitution test (DSST) and trail making test (TMT), parts A and B. The effect sizes of socio-demographic (age, sex, education), lifestyle (alcohol, tobacco, physical activity), cardiovascular (diabetes, blood pressure) and psychological (depressive symptomatology) variables were computed as omega-squared coefficients (ω 2 ; part of the variation of a neuropsychological score that is independently explained by a given variable). These sets of variables explained from R 2 = 10% (semantic fluency) to R 2 = 26% (DSST) of the total variance. In all tests, socio-demographic variables accounted for the greatest part of the explained variance. Age explained from ω 2 = 0.5% (semantic fluency) to ω 2 = 7.5% (DSST) of the total score variance, gender from ω 2 = 5.2% (FCSRT) to a negligible part (semantic fluency or TMT) and education from ω 2 = 7.2% (DSST) to ω 2 = 1.4% (TMT-A). Behavioral, cardiovascular and psychological variables only slightly influenced the cognitive test results (all ω 2 < 0.8%, most ω 2 < 0.1%). Socio-demographic variables (age, gender and education) are the main variables associated with cognitive performance variations between 45 and 75 years of age in the general population. © 2016 EAN.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGreevy, John Austen; /Stanford U., Phys. Dept.

This thesis is a study of D-branes in string compactifications. In this context, D-branes are relevant as an important component of the nonperturbative spectrum, as an incisive probe of these backgrounds, and as a natural stringy tool for localizing gauge interactions. In the first part of the thesis, we discuss half-BPS D-branes in compactifications of type II string theory on Calabi-Yau threefolds. The results we describe for these objects are pertinent both in their role as stringy brane-worlds, and in their role as solitonic objects. In particular, we determine couplings of these branes to the moduli determining the closed-string geometry,more » both perturbatively and non-perturbatively in the worldsheet expansion. We provide a local model for transitions in moduli space where the BPS spectrum jumps, and discuss the extension of mirror symmetry between Calabi-Yau manifolds to the case when D-branes are present. The next section is an interlude which provides some applications of D-branes to other curved backgrounds of string theory. In particular, we discuss a surprising phenomenon in which fundamental strings moving through background Ramond-Ramond fields dissolve into large spherical D3-branes. This mechanism is used to explain a previously-mysterious fact discovered via the AdS-CFT correspondence. Next, we make a connection between type IIA string vacua of the type discussed in the first section and M-theory compactifications on manifolds of G{sub 2} holonomy. Finally we discuss constructions of string vacua which do not have large radius limits. In the final part of the thesis, we develop techniques for studying the worldsheets of open strings ending on the curved D-branes studied in the first section. More precisely, we formulate a large class of massive two-dimensional gauge theories coupled to boundary matter, which flow in the infrared to the relevant boundary conformal field theories. Along with many other applications, these techniques are used to describe world-volume theories of point-like D-probes of various Calabi-Yau threefolds.« less

NASTRAN Structural Model for the Large 64-meter Antenna Pedestal. Part 3: Applications to Hydrostatic Bearing Oil Film

NASA Technical Reports Server (NTRS)

Chian, C. T.; Schonfeld, D.

1984-01-01

Investigations are conducted on the 64-meter antenna hydrostatic bearing oil film thickness under a variety of loads and elastic moduli. These parametric studies use a NASTRAN pedestal structural model to determine the deflections under the hydrostatic bearing pad. The deflections form the input for a computer program to determine the hydrostatic bearing oil film thickness. For the future 64-meter to 70-meter antenna extension and for the 2.2-meter (86-in.) haunch concrete replacement cases, safe oil film thickness (greater than 0.13 mm (0.005 in.) at the corners of the pad) are predicted. The effects of varying moduli of elasticity for different sections of the pedestal and the film height under distressed runner conditions are also studied.

Estimation of critical behavior from the density of states in classical statistical models

NASA Astrophysics Data System (ADS)

Malakis, A.; Peratzakis, A.; Fytas, N. G.

2004-12-01

We present a simple and efficient approximation scheme which greatly facilitates the extension of Wang-Landau sampling (or similar techniques) in large systems for the estimation of critical behavior. The method, presented in an algorithmic approach, is based on a very simple idea, familiar in statistical mechanics from the notion of thermodynamic equivalence of ensembles and the central limit theorem. It is illustrated that we can predict with high accuracy the critical part of the energy space and by using this restricted part we can extend our simulations to larger systems and improve the accuracy of critical parameters. It is proposed that the extensions of the finite-size critical part of the energy space, determining the specific heat, satisfy a scaling law involving the thermal critical exponent. The method is applied successfully for the estimation of the scaling behavior of specific heat of both square and simple cubic Ising lattices. The proposed scaling law is verified by estimating the thermal critical exponent from the finite-size behavior of the critical part of the energy space. The density of states of the zero-field Ising model on these lattices is obtained via a multirange Wang-Landau sampling.

Method for compression of data using single pass LZSS and run-length encoding

DOEpatents

Berlin, G.J.

1994-01-01

A method used preferably with LZSS-based compression methods for compressing a stream of digital data. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer.

Engineering and characterization of fluorogenic glycine riboswitches

PubMed Central

Ketterer, Simon; Gladis, Lukas; Kozica, Adnan; Meier, Matthias

2016-01-01

A set of 12 fluorogenic glycine riboswitches with different thermodynamic and kinetic response properties was engineered. For the design of functional riboswitches, a three-part RNA approach was applied based on the idea of linking a RNA sensor, transmitter and actuator part together. For the RNA sensor and actuator part, we used the tandem glycine aptamer structure from Bacillus subtillis, and fluorogenic aptamer Spinach, respectively. To achieve optimal signal transduction from the sensor to the actuator, a riboswitch library with variable transmitter was screened with a microfluidic large-scale integration chip. This allowed us to establish the complete thermodynamic binding profiles of the riboswitch library. Glycine dissociation constants of the 12 strong fluorescence response riboswitches varied between 99.7 and 570 μM. Furthermore, the kinetic glycine binding (kon), and dissociation (koff) rates, and corresponding energy barriers of the 10 strongest fluorescence response riboswitches were determined with the same chip platform. kon and koff were in the order of 10−3s−1 and 10−2s−1, respectively. Conclusively, we demonstrate that systematic screening of synthetic and natural linked RNA parts with microfluidic chip technology is an effective approach to rapidly generate fluorogenic metabolite riboswitches with a broad range of biophysical response properties. PMID:27220466

Method for compression of data using single pass LZSS and run-length encoding

DOEpatents

Berlin, Gary J.

1997-01-01

A method used preferably with LZSS-based compression methods for compressing a stream of digital data. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer.

Geophysical Investigations of the Smoke Creek Desert and their Geologic Implications, Northwest Nevada and Northeast California

USGS Publications Warehouse

Ponce, David A.; Glen, Jonathan M.G.; Tilden, Janet E.

2006-01-01

The Smoke Creek Desert is a large basin about 100 km (60 mi) north of Reno near the California-Nevada border, situated along the northernmost parts of the Walker Lane Belt, a physiographic region defined by diverse topographic expression consisting of northweststriking topographic features and strike-slip faulting. Because geologic and geophysical framework studies play an important role in understanding the hydrogeology of the Smoke Creek Desert, a geophysical effort was undertaken to help determine basin geometry, infer structural features, and estimate depth to basement. In the northernmost parts of the Smoke Creek Desert basin, along Squaw Creek Valley, geophysical data indicate that the basin is shallow and that granitic rocks are buried at shallow depths throughout the valley. These granitic rocks are faulted and fractured and presumably permeable, and thus may influence ground-water resources in this area. The Smoke Creek Desert basin itself is composed of three large oval sub-basins, all of which reach depths to basement of up to about 2 km (1.2 mi). In the central and southern parts of the Smoke Creek Desert basin, magnetic anomalies form three separate and narrow EW-striking features. These features consist of high-amplitude short-wavelength magnetic anomalies and probably reflect Tertiary basalt buried at shallow depth. In the central part of the Smoke Creek Desert basin a prominent EW-striking gravity and magnetic prominence extends from the western margin of the basin to the central part of the basin. Along this ridge, probably composed of Tertiary basalt, overlying unconsolidated basin-fill deposits are relatively thin (< 400 m). The central part of the Smoke Creek Desert basin is also characterized by the Mid-valley fault, a continuous geologic and geophysical feature striking NS and at least 18-km long, possibly connecting with faults mapped in the Terraced Hills and continuing southward to Pyramid Lake. The Mid-valley fault may represent a lateral (east-west) barrier to ground-water flow. In addition, the Mid-valley fault may also be a conduit for along-strike (north-south) ground-water flow, channeling flow to the southernmost parts of the basin and the discharge areas north of Sand Pass.

[Comparison of three histometric methods for the comprehension of stimulating effects on the rat thyroid gland].

PubMed

Herrmann, F; Hambsch, K; Wolf, T; Rother, P; Müller, P

1989-01-01

There exist some histometric methods for the morphological quantification of different strongly stimulating effects on the thyroid gland induced by drugs and/or other chemical substances in dependence upon dose and duration of application. But in respect of technical and temporal expense and also diagnostic statement, there are considerable differences between these recording procedures. Therefore we examined the 3 mostly used methods synchronously (i.e. determination of thyroid epithelial cell height, nuclear volume in thyrocytes, and estimation of relative volume parts in the thyroid gland by the point counting method) by investigating the thyroid glands of methylthiouracil-(MTU)-stimulated rats and corresponding controls in order to compare the diagnostic value and temporal expense. The largest temporal expense was required in the nuclear volume determination, the smallest in the point-counting method. On principle, all 3 procedures allow the determination of hypertrophic alterations but only by help of the point-counting method, also hyperplastic changes are recognizable. By nuclear volume determination, we found significant differences between central and peripheral parts of the thyroid gland. Therefore, to avoid the subjective error, it will be necessary to measure a large number of nuclei in many planes of the gland. Also the determination of epithelial cell high reinforces the subjective error because of the heterological structure especially in unstimulated thyroid gland. If the number of counting points is exactly determined and, full of sense, limited, the point-counting method allows a nearly complete measuring of the whole object to be tested within an acceptable investigation time. In this way, the heterological structure of thyroid gland will be regarded, and comparability and reproducibility are guaranteed on an high level.

Accelerometer-based physical activity in a large observational cohort--study protocol and design of the activity and function of the elderly in Ulm (ActiFE Ulm) study.

PubMed

Denkinger, Michael D; Franke, Sebastian; Rapp, Kilian; Weinmayr, Gudrun; Duran-Tauleria, Enric; Nikolaus, Thorsten; Peter, Richard

2010-07-27

A large number of studies have demonstrated a positive effect of increased physical activity (PA) on various health outcomes. In all large geriatric studies, however, PA has only been assessed by interview-based instruments which are all subject to substantial bias. This may represent one reason why associations of PA with geriatric syndromes such as falls show controversial results. The general aim of the Active-Ulm study was to determine the association of accelerometer-based physical activity with different health-related parameters, and to study the influence of this standardized objective measure of physical activity on health- and disability-related parameters in a longitudinal setting. We have set up an observational cohort study in 1500 community dwelling older persons (65 to 90 years) stratified by age and sex. Addresses have been obtained from the local residents registration offices. The study is carried out jointly with the IMCA--Respiratory Health Survey in the Elderly implemented in the context of the European project IMCA II. The study has a cross-sectional part (1) which focuses on PA and disability and two longitudinal parts (2) and (3). The primary information for part (2) is a prospective 1 year falls calendar including assessment of medication change. Part (3) will be performed about 36 months following baseline. Primary variables of interest include disability, PA, falls and cognitive function. Baseline recruitment has started in March 2009 and will be finished in April 2010.All participants are visited three times within one week, either at home or in the study center. Assessments included interviews on quality of life, diagnosed diseases, common risk factors as well as novel cognitive tests and established tests of physical functioning. PA is measured using an accelerometer-based sensor device, carried continuously over a one week period and accompanied by a prospective activity diary. The assessment of PA using a high standard accelerometer-based device is feasible in a large population-based study. The results obtained from cross-sectional and longitudinal analyses will shed light on important associations between PA and various outcomes and may provide information for specific interventions in older people.

Analysis of Critical Parts and Materials

DTIC Science & Technology

1980-12-01

1 1 1% 1% 1% 1% Large Orders Manual Ordering of Some Critical Parts Order Spares with Original Order Incentives Belter Capital Investment...demand 23 Large orders 24 Long lead procurement funding (including raw materials, facility funding) 25 Manpower analysis and training 26 Manual ... ordering of some critical parts 27 More active role in schedule negotiation 28 Multiple source procurements 29 Multi-year program funding 30 Order

Investigation of hydroelastic ship responses of an ULOC in head seas

NASA Astrophysics Data System (ADS)

Wang, Xue-liang; Temarel, Pandeli; Hu, Jia-jun; Gu, Xue-kang

2016-10-01

Investigation of hydroelastic ship responses has been brought to the attention of the scientific and engineering world for several decades. There are two kinds of high-frequency vibrations in general ship responses to a large ocean-going ship in its shipping line, so-called springing and whipping, which are important for the determination of design wave load and fatigue damage as well. Because of the huge scale of an ultra large ore carrier (ULOC), it will suffer seldom slamming events in the ocean. The resonance vibration with high frequency is springing, which is caused by continuous wave excitation. In this paper, the wave-induced vibrations of the ULOC are addressed by experimental and numerical methods according to 2D and 3D hydroelasticity theories and an elastic model under full-load and ballast conditions. The influence of loading conditions on high-frequency vibration is studied both by numerical and experimental results. Wave-induced vibrations are higher under ballast condition including the wave frequency part, the multiple frequencies part, the 2-node and the 3-node vertical bending parts of the hydroelastic responses. The predicted results from the 2D method have less accuracy than the 3D method especially under ballast condition because of the slender-body assumption in the former method. The applicability of the 2D method and the further development of nonlinear effects to 3D method in the prediction of hydroelastic responses of the ULOC are discussed.

Computational design of RNA parts, devices, and transcripts with kinetic folding algorithms implemented on multiprocessor clusters.

PubMed

Thimmaiah, Tim; Voje, William E; Carothers, James M

2015-01-01

With progress toward inexpensive, large-scale DNA assembly, the demand for simulation tools that allow the rapid construction of synthetic biological devices with predictable behaviors continues to increase. By combining engineered transcript components, such as ribosome binding sites, transcriptional terminators, ligand-binding aptamers, catalytic ribozymes, and aptamer-controlled ribozymes (aptazymes), gene expression in bacteria can be fine-tuned, with many corollaries and applications in yeast and mammalian cells. The successful design of genetic constructs that implement these kinds of RNA-based control mechanisms requires modeling and analyzing kinetically determined co-transcriptional folding pathways. Transcript design methods using stochastic kinetic folding simulations to search spacer sequence libraries for motifs enabling the assembly of RNA component parts into static ribozyme- and dynamic aptazyme-regulated expression devices with quantitatively predictable functions (rREDs and aREDs, respectively) have been described (Carothers et al., Science 334:1716-1719, 2011). Here, we provide a detailed practical procedure for computational transcript design by illustrating a high throughput, multiprocessor approach for evaluating spacer sequences and generating functional rREDs. This chapter is written as a tutorial, complete with pseudo-code and step-by-step instructions for setting up a computational cluster with an Amazon, Inc. web server and performing the large numbers of kinefold-based stochastic kinetic co-transcriptional folding simulations needed to design functional rREDs and aREDs. The method described here should be broadly applicable for designing and analyzing a variety of synthetic RNA parts, devices and transcripts.

Determination of Process Parameters in Multi-Stage Hydro-Mechanical Deep Drawing by FE Simulation

NASA Astrophysics Data System (ADS)

Kumar, D. Ravi; Manohar, M.

2017-09-01

In this work, analysis has been carried to simulate manufacturing of a near hemispherical bottom part with large depth by hydro-mechanical deep drawing with an aim to reduce the number of forming steps and to reduce the extent of thinning in the dome region. Inconel 718 has been considered as the material due to its importance in aerospace industry. It is a Ni-based super alloy and it is one of the most widely used of all super alloys primarily due to large-scale applications in aircraft engines. Using Finite Element Method (FEM), numerical simulations have been carried out for multi-stage hydro-mechanical deep drawing by using the same draw ratios and design parameters as in the case of conventional deep drawing in four stages. The results showed that the minimum thickness in the final part can be increased significantly when compared to conventional deep drawing. It has been found that the part could be deep drawn to the desired height (after trimming at the final stage) without any severe wrinkling. Blank holding force (BHF) and peak counter pressure have been found to have a strong influence on thinning in the component. Decreasing the coefficient of friction has marginally increased the minimum thickness in the final component. By increasing the draw ratio and optimizing BHF, counter pressure and die corner radius in the simulations, it has been found that it is possible to draw the final part in three stages. It has been found that thinning can be further reduced by decreasing the initial blank size without any reduction in the final height. This reduced the draw ratio at every stage and optimum combination of BHF and counter pressure have been found for the 3-stage process also.

Explosive force of primacord grid forms large sheet metal parts

NASA Technical Reports Server (NTRS)

1966-01-01

Primacord which is woven through fish netting in a grid pattern is used for explosive forming of large sheet metal parts. The explosive force generated by the primacord detonation is uniformly distributed over the entire surface of the sheet metal workpiece.

Chlorofluorocarbons, sulfur hexafluoride, and dissolved permanent gases in ground water from selected sites in and near the Idaho National Engineering and Environmental Laboratory, Idaho, 1994-97

USGS Publications Warehouse

Busenberg, Eurybiades; Plummer, Niel; Bartholomay, Roy C.; Wayland, Julian E.

1998-01-01

From July 1994 through May 1997, the U.S. Geological Survey in cooperation with the Department of Energy, sampled 86 wells completed in the Snake River Plain aquifer at and near the Idaho N ationa1 Engineering and Environmental Laboratory (INEEL). The wells were sampled for a variety of constituents including one- and two-carbon halocarbons. Concentrations of dichlorodifluoromethane (CFC-12), trichlorofluoromethane (CFC-11) and trichlorotrifluororoethane (CFC-113) were determined. The samples for halocarbon analysis were collected in 62-milliliter flame sealed borosilicate glass ampoules in the field. The data will be used to evaluate the ages of ground waters at INEEL. The ages of the ground water will be used to determine recharge rates, residence time, and travel time of water in the Snake River Plain aquifer in and near INEEL. The chromatograms of 139 ground waters are presented showing a large number of halomethanes, haloethanes, and haloethenes present in the ground waters underlying the INEEL. The chromatograms can be used to qualitatively evaluate a large number of contaminants at parts per trillion to parts per billion concentrations. The data can be used to study temporal and spatial distribution of contaminants in the Snake River Plain aquifer. Representative compressed chromatograms for all ground waters sampled in this study are available on two 3.5-inch high density computer disks. The data and the program required to decompress the data can be obtained from the U.S. Geological Survey office at Idaho Falls, Idaho. Sulfur hexafluoride (SF6) concentrations were measured in selected wells to determine the feasibility of using this environmental tracer as an age dating tool of ground water. Concentrations of dissolved nitrogen, argon, carbon dioxide, oxygen, and methane were measured in 79 ground waters. Concentrations of dissolved permanent gases are tabulated and will be used to evaluate the temperature of recharge of ground water in and near the INEEL.

Consumer participation in the planning and delivery of drug treatment services: the current arrangements.

PubMed

Bryant, Joanne; Saxton, Melissa; Madden, Annie; Bath, Nicky; Robinson, Suzanne

2008-03-01

Consumer participation in decision-making about service planning is common in certain health services in Australia but is thought to be largely underdeveloped in drug treatment services. This paper (1) describes the current practices within Australian drug treatment services that aim to include consumers in service planning and provision; and (2) determines how much consumers know about the existing opportunities for involvement. Sixty-four randomly selected service providers (representing 64 separate services) completed interviews about the current arrangements for consumer participation within their services (response rate = 82%). A total of 179 consumers completed interviews assessing their knowledge of the consumer participation activities available at the service they attended. Consumer participation activities were not uncommon in drug treatment services, although the existing activities were concerned largely with providing information to or receiving information from consumers. Activities that included consumers in higher forms of involvement, such as those in which consumers took part in decision-making, were largely uncommon. Consumers had a considerable lack of knowledge about the participation activities available to them, revealing a lack of communication between providers and consumers. While service providers were making efforts to engage consumers in service planning and provision (despite the general lack of State or Commonwealth policy directives and extra funding to do so), these appear ineffectual because of poor communication between providers and consumers. As a starting point, a critical part of any meaningful consumer participation initiative must include systems to ensure that consumers know about available opportunities.

Rapid analysis of perchlorate in drinking water at parts per billion levels using microchip electrophoresis.

PubMed

Gertsch, Jana C; Noblitt, Scott D; Cropek, Donald M; Henry, Charles S

2010-05-01

A microchip capillary electrophoresis (MCE) system has been developed for the determination of perchlorate in drinking water. The United States Environmental Protection Agency (USEPA) recently proposed a health advisory limit for perchlorate in drinking water of 15 parts per billion (ppb), a level requiring large, sophisticated instrumentation, such as ion chromatography coupled with mass spectrometry (IC-MS), for detection. An inexpensive, portable system is desired for routine online monitoring applications of perchlorate in drinking water. Here, we present an MCE method using contact conductivity detection for perchlorate determination. The method has several advantages, including reduced analysis times relative to IC, inherent portability, high selectivity, and minimal sample pretreatment. Resolution of perchlorate from more abundant ions was achieved using zwitterionic, sulfobetaine surfactants, N-hexadecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (HDAPS) and N-tetradecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (TDAPS). The system performance and the optimization of the separation chemistry, including the use of these surfactants to resolve perchlorate from other anions, are discussed in this work. The system is capable of detection limits of 3.4 +/- 1.8 ppb (n = 6) in standards and 5.6 +/- 1.7 ppb (n = 6) in drinking water.

Evaluating options for balancing the water-electricity nexus in California: part 1--securing water availability.

PubMed

Tarroja, Brian; AghaKouchak, Amir; Sobhani, Reza; Feldman, David; Jiang, Sunny; Samuelsen, Scott

2014-11-01

The technical potential and effectiveness of different water supply options for securing water availability in a large-scale, interconnected water supply system under historical and climate-change augmented inflow and demand conditions were compared. Part 1 of the study focused on determining the scale of the options required to secure water availability and compared the effectiveness of different options. A spatially and temporally resolved model of California's major surface reservoirs was developed, and its sensitivity to urban water conservation, desalination, and water reuse was examined. Potential capacities of the different options were determined. Under historical (baseline) hydrology conditions, many individual options were found to be capable of securing water availability alone. Under climate change augment conditions, a portfolio approach was necessary. The water savings from many individual options other than desalination were insufficient in the latter, however, relying on seawater desalination alone requires extreme capacity installations which have energy, brine disposal, management, and cost implications. The importance of identifying and utilizing points of leverage in the system for choosing where to deploy different options is also demonstrated. Copyright © 2014 Elsevier B.V. All rights reserved.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2017-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

A model for distribution centers location-routing problem on a multimodal transportation network with a meta-heuristic solving approach

NASA Astrophysics Data System (ADS)

Fazayeli, Saeed; Eydi, Alireza; Kamalabadi, Isa Nakhai

2018-07-01

Nowadays, organizations have to compete with different competitors in regional, national and international levels, so they have to improve their competition capabilities to survive against competitors. Undertaking activities on a global scale requires a proper distribution system which could take advantages of different transportation modes. Accordingly, the present paper addresses a location-routing problem on multimodal transportation network. The introduced problem follows four objectives simultaneously which form main contribution of the paper; determining multimodal routes between supplier and distribution centers, locating mode changing facilities, locating distribution centers, and determining product delivery tours from the distribution centers to retailers. An integer linear programming is presented for the problem, and a genetic algorithm with a new chromosome structure proposed to solve the problem. Proposed chromosome structure consists of two different parts for multimodal transportation and location-routing parts of the model. Based on published data in the literature, two numerical cases with different sizes generated and solved. Also, different cost scenarios designed to better analyze model and algorithm performance. Results show that algorithm can effectively solve large-size problems within a reasonable time which GAMS software failed to reach an optimal solution even within much longer times.

Mechanisms and Evolution of Control Logic in Prokaryotic Transcriptional Regulation

PubMed Central

van Hijum, Sacha A. F. T.; Medema, Marnix H.; Kuipers, Oscar P.

2009-01-01

Summary: A major part of organismal complexity and versatility of prokaryotes resides in their ability to fine-tune gene expression to adequately respond to internal and external stimuli. Evolution has been very innovative in creating intricate mechanisms by which different regulatory signals operate and interact at promoters to drive gene expression. The regulation of target gene expression by transcription factors (TFs) is governed by control logic brought about by the interaction of regulators with TF binding sites (TFBSs) in cis-regulatory regions. A factor that in large part determines the strength of the response of a target to a given TF is motif stringency, the extent to which the TFBS fits the optimal TFBS sequence for a given TF. Advances in high-throughput technologies and computational genomics allow reconstruction of transcriptional regulatory networks in silico. To optimize the prediction of transcriptional regulatory networks, i.e., to separate direct regulation from indirect regulation, a thorough understanding of the control logic underlying the regulation of gene expression is required. This review summarizes the state of the art of the elements that determine the functionality of TFBSs by focusing on the molecular biological mechanisms and evolutionary origins of cis-regulatory regions. PMID:19721087

Migration and Western europe: the old world turning new.

PubMed

Therborn, G

1987-09-04

The 1960s meant a historical turn of Western Europe, becoming an immigration area. Net immigration has been concentrated to some of the prosperous Western European countries and has been mainly determined by the demand of their particular national labor regimes. The size of alien employment has been very differently affected by the 1973 crisis, but a multiethnical society will remain a novel feature of most Western European countries. Political abdication from full employment and technological change makes a ghetto of un(der)employment a likely prospect of a large part of the second generation of recent immigrants into Western Europe.

Signature extension studies

NASA Technical Reports Server (NTRS)

Vincent, R. K.; Thomas, G. S.; Nalepka, R. F.

1974-01-01

The importance of specific spectral regions to signature extension is explored. In the recent past, the signature extension task was focused on the development of new techniques. Tested techniques are now used to investigate this spectral aspect of the large area survey. Sets of channels were sought which, for a given technique, were the least affected by several sources of variation over four data sets and yet provided good object class separation on each individual data set. Using sets of channels determined as part of this study, signature extension was accomplished between data sets collected over a six-day period and over a range of about 400 kilometers.

Identifying the principal coefficient of parabolic equations with non-divergent form

NASA Astrophysics Data System (ADS)

Jiang, L. S.; Bian, B. J.

2005-01-01

We deal with an inverse problem of determining a coefficient a(x, t) of principal part for second order parabolic equations with non-divergent form when the solution is known. Such a problem has important applications in a large fields of applied science. We propose a well-posed approximate algorithm to identify the coefficient. The existence, uniqueness and stability of such solutions a(x, t) are proved. A necessary condition which is a couple system of a parabolic equation and a parabolic variational inequality is deduced. Our numerical simulations show that the coefficient is recovered very well.

Object-based selection in the Baylis and Driver (1993) paradigm is subject to space-based attentional modulation.

PubMed

Müller, Hermann J; O'Grady, Rebecca; Krummenacher, Joseph; Heller, Dieter

2008-11-01

Three experiments re-examined Baylis and Driver's (1993) strong evidence for object-based selection, that making relative apex location judgments is harder between two objects than within a single object, with object (figure-ground) segmentation determined solely by color-based perceptual set. Using variations of the Baylis and Driver paradigm, the experiments replicated a two-object cost. However, they also showed a large part of the two-object cost to be attributable to space-based factors, though there remained an irreducible cost consistent with 'true' object-based selection.

Summation-by-Parts operators with minimal dispersion error for coarse grid flow calculations

NASA Astrophysics Data System (ADS)

Linders, Viktor; Kupiainen, Marco; Nordström, Jan

2017-07-01

We present a procedure for constructing Summation-by-Parts operators with minimal dispersion error both near and far from numerical interfaces. Examples of such operators are constructed and compared with a higher order non-optimised Summation-by-Parts operator. Experiments show that the optimised operators are superior for wave propagation and turbulent flows involving large wavenumbers, long solution times and large ranges of resolution scales.

Characterizing Long-Term Groundwater Conditions and Lithology for the Design of Large-Scale Borehole Heat Exchangers

NASA Astrophysics Data System (ADS)

Smith, David Charles

Construction of large scale ground coupled heat pump (GCHP) systems that operate with hundreds or even thousands of boreholes for the borehole heat exchangers (BHE) has increased in recent years with many coming on line in the past 10 years. Many large institutions are constructing these systems because of their ability to store energy in the subsurface for indoor cooling during the warm summer months and extract that energy for heating during the cool winter months. Despite the increase in GCHP system systems constructed, there have been few long term studies on how these large systems interact with the subsurface. The thermal response test (TRT) is the industry standard for determining the thermal properties of the rock and soil. The TRT is limited in that it can only be used to determine the effective thermal conductivity over the whole length of a single borehole at the time that it is administered. The TRT cannot account for long-term changes in the aquifer saturation, changes in groundwater flow, or characterize different rock and soil units by effectiveness for heat storage. This study established new methods and also the need for the characterization of the subsurface for the purpose of design and long-term monitoring for GCHP systems. These new methods show that characterizing the long-term changes in aquifer saturation and groundwater flow, and characterizing different rock and soil units are an important part of the design and planning process of these systems. A greater understanding of how large-scale GCHP systems interact with the subsurface will result in designs that perform more efficiently over a longer period of time and expensive modifications due to unforeseen changes in system performance will be reduced.

Tachyon condensation and quark mass in the modified Sakai-Sugimoto model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhar, Avinash; High Energy Accelerator Research Organization; Nag, Partha

2008-09-15

This paper continues the investigation of the modified Sakai-Sugimoto model proposed previously [J. High Energy Phys. 01 (2008) 055]. Here we discuss in detail numerical solutions to the classical equations for the brane profile and the tachyon condensate. An ultraviolet cutoff turns out to be essential because the numerical solutions tend to rapidly diverge from the desired asymptotic solutions, beyond a sufficiently large value of the holographic coordinate. The required cutoff is determined by the non-normalizable part of the tachyon and is parametrically far smaller than that dictated by consistency of a description in terms of ten-dimensional bulk gravity. Wemore » had argued [J. High Energy Phys. 01 (2008) 055] that the solution in which the tachyon field goes to infinity at the point where the brane and antibrane meet has only one free parameter, which may be taken to be the asymptotic brane-antibrane separation. Here we present numerical evidence in favor of this observation. We also present evidence that the non-normalizable part of the asymptotic tachyon solution, which is identified with quark mass in the QCD-like boundary theory, is determined by this parameter. We show that the normalizable part of the asymptotic tachyon solution determines the quark condensate, but this requires holographic renormalization of the on-shell boundary brane action because of the presence of infinite cutoff-dependent terms. Our renormalization scheme gives an exponential dependence on the cutoff to the quark mass. We also discuss meson spectra in detail and show that the pion mass is nonzero and satisfies the Gell-Mann-Oakes-Renner relation when a small quark mass is switched on.« less

Drugs for rare disorders.

PubMed

Cremers, Serge; Aronson, Jeffrey K

2017-08-01

Estimates of the frequencies of rare disorders vary from country to country; the global average defined prevalence is 40 per 100 000 (0.04%). Some occur in only one or a few patients. However, collectively rare disorders are fairly common, affecting 6-8% of the US population, or about 30 million people, and a similar number in the European Union. Most of them affect children and most are genetically determined. Diagnosis can be difficult, partly because of variable presentations and partly because few clinicians have experience of individual rare disorders, although they may be assisted by searching databases. Relatively few rare disorders have specific pharmacological treatments (so-called orphan drugs), partly because of difficulties in designing trials large enough to determine benefits and harms alike. Incentives have been introduced to encourage the development of orphan drugs, including tax credits and research aids, simplification of marketing authorization procedures and exemption from fees, and extended market exclusivity. Consequently, the number of applications for orphan drugs has grown, as have the costs of using them, so much so that treatments may not be cost-effective. It has therefore been suggested that not-for-profit organizations that are socially motivated to reduce those costs should be tasked with producing them. A growing role for patient organizations, improved clinical and translational infrastructures, and developments in genetics have also contributed to successful drug development. The translational discipline of clinical pharmacology is an essential component in drug development, including orphan drugs. Clinical pharmacologists, skilled in basic pharmacology and its links to clinical medicine, can be involved at all stages. They can contribute to the delineation of genetic factors that determine clinical outcomes of pharmacological interventions, develop biomarkers, design and perform clinical trials, assist regulatory decision making, and conduct postmarketing surveillance and pharmacoepidemiological and pharmacoeconomic assessments. © 2017 The British Pharmacological Society.

Kansas coal distribution, resources, and potential for coalbed methane

USGS Publications Warehouse

Brady, L.L.

2000-01-01

100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth Kansas has large amounts of bituminous coal both at the surface and in the subsurface of eastern Kansas. Preliminary studies indicate at least 53 billion tons (48 billion MT) of deep coal [>100 ft (>30 m)] determined from 32 different coal beds. Strippable coal resources at a depth < 100 ft (<30 m) total 2.8 billion tons (2.6 billion MT), and this total is determined from 17 coals. Coal beds present in the Cherokee Group (Middle Pennsylvanian) represent most of these coal resource totals. Deep coal beds with the largest resource totals include the Bevier, Mineral, "Aw" (unnamed coal bed), Riverton, and Weir-Pittsburg coals, all within the Cherokee Group. Based on chemical analyses, coals in the southeastern part of the state are generally high volatile A bituminous, whereas coals in the east-central and northeastern part of the state are high-volatile B bituminous coals. The primary concern of coal beds in Kansas for deep mining or development of coalbed methane is the thin nature [<2 ft (0.6 m)] of most coal beds. Present production of coalbed methane is centered mainly in the southern Wilson/northern Montgomery County area of southeastern Kansas where methane is produced from the Mulky, Weir-Pittsburg, and Riverton coals.

METHODS FOR THE DETERMINATION OF TOTAL ORGANIC ...

EPA Pesticide Factsheets

Organic matter in soils and sediments is widely distributed over the earth's surface occurring in almost all terrestrial and aquatic environments (Schnitzer, 1978). Soils and sediments contain a large variety of organic materials ranging from simple sugars and carbohydrates to the more complex proteins, fats, waxes, and organic acids. Important characteristics of the organic matter include their ability to: form water-soluble and water- insoluble complexes with metal ions and hydrous oxides; interact with clay minerals and bind particles together; sorb and desorb both naturally-occurring and anthropogenically-introduced organic compounds; absorb and release plant nutrients; and hold water in the soil environment. As a result of these characteristics, the determination of total organic carbon (a measure of one of the chemical components of organic matter that is often used as an indicator of its presence in a soil or sediment) is an essential part of any site characterization since its presence or absence can markedly influence how chemicals will react in the soil or sediment. Soil and sediment total organic carbon (TOC) determinations are typically requested with contaminant analyses as part of an ecological risk assessment data package. TOC contents may be used qualitatively to assess the nature of the sampling location (e.g., was it a depositional area) or may be used to normalize portions of the analytical chemistry data set (e.g., equilibrium partitioning).

Effects of groundwater flow on the distribution of biogenic gas in parts of the northern Great Plains of Canada and United States

USGS Publications Warehouse

Anna, Lawrence O.

2011-01-01

Parts of the northern Great Plains in eastern Montana and western North Dakota and southeastern Alberta and southwestern Saskatchewan, Canada, were studied as part of an assessment of shallow biogenic gas in Upper Cretaceous rocks.Parts of the northern Great Plains in eastern Montana and western North Dakota and southeastern Alberta and southwestern Saskatchewan, Canada, were studied as part of an assessment of shallow biogenic gas in Upper Cretaceous rocks. Large quantities of shallow biogenic gas are produced from low-permeability, Upper Cretaceous reservoirs in southeastern Alberta and southwestern Saskatchewan, Canada. Rocks of similar types and age produce sparingly in the United States except on large structures, such as Bowdoin dome and Cedar Creek anticline. Significant production also occurs in the Tiger Ridge area, where uplift of the Bearpaw Mountains created stratigraphic traps. The resource in Canada is thought to be a continuous, biogenic-gas-type accumulation with economic production in a variety of subtle structures and stratigraphic settings. The United States northern Great Plains area has similar conditions but only broad structural closures or stratigraphic traps associated with local structure have produced economically to date. Numerical flow modeling was used to help determine that biogenic gas in low-permeability reservoirs is held in place by high hydraulic head that overrides buoyancy forces of the gas. Modeling also showed where hydraulic head is greater under Tertiary capped topographic remnants rather than near adjacent topographic lows. The high head can override the capillary pressure of the rock and force gas to migrate to low head in topographically low areas. Most current biogenic gas production is confined to areas between mapped lineaments in the northern Great Plains. The lineaments may reflect structural zones in the Upper Cretaceous that help compartmentalize reservoirs and confine gas accumulations.

Modelling turbulent boundary layer flow over fractal-like multiscale terrain using large-eddy simulations and analytical tools.

PubMed

Yang, X I A; Meneveau, C

2017-04-13

In recent years, there has been growing interest in large-eddy simulation (LES) modelling of atmospheric boundary layers interacting with arrays of wind turbines on complex terrain. However, such terrain typically contains geometric features and roughness elements reaching down to small scales that typically cannot be resolved numerically. Thus subgrid-scale models for the unresolved features of the bottom roughness are needed for LES. Such knowledge is also required to model the effects of the ground surface 'underneath' a wind farm. Here we adapt a dynamic approach to determine subgrid-scale roughness parametrizations and apply it for the case of rough surfaces composed of cuboidal elements with broad size distributions, containing many scales. We first investigate the flow response to ground roughness of a few scales. LES with the dynamic roughness model which accounts for the drag of unresolved roughness is shown to provide resolution-independent results for the mean velocity distribution. Moreover, we develop an analytical roughness model that accounts for the sheltering effects of large-scale on small-scale roughness elements. Taking into account the shading effect, constraints from fundamental conservation laws, and assumptions of geometric self-similarity, the analytical roughness model is shown to provide analytical predictions that agree well with roughness parameters determined from LES.This article is part of the themed issue 'Wind energy in complex terrains'. © 2017 The Author(s).

Adding muscle where you need it: non-uniform hypertrophy patterns in elite sprinters.

PubMed

Handsfield, G G; Knaus, K R; Fiorentino, N M; Meyer, C H; Hart, J M; Blemker, S S

2017-10-01

Sprint runners achieve much higher gait velocities and accelerations than average humans, due in part to large forces generated by their lower limb muscles. Various factors have been explored in the past to understand sprint biomechanics, but the distribution of muscle volumes in the lower limb has not been investigated in elite sprinters. In this study, we used non-Cartesian MRI to determine muscle sizes in vivo in a group of 15 NCAA Division I sprinters. Normalizing muscle sizes by body size, we compared sprinter muscles to non-sprinter muscles, calculated Z-scores to determine non-uniformly large muscles in sprinters, assessed bilateral symmetry, and assessed gender differences in sprinters' muscles. While limb musculature per height-mass was 22% greater in sprinters than in non-sprinters, individual muscles were not all uniformly larger. Hip- and knee-crossing muscles were significantly larger among sprinters (mean difference: 30%, range: 19-54%) but only one ankle-crossing muscle was significantly larger (tibialis posterior, 28%). Population-wide asymmetry was not significant in the sprint population but individual muscle asymmetries exceeded 15%. Gender differences in normalized muscle sizes were not significant. The results of this study suggest that non-uniform hypertrophy patterns, particularly large hip and knee flexors and extensors, are advantageous for fast sprinting. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

General contraction of Gaussian basis sets. Part 2: Atomic natural orbitals and the calculation of atomic and molecular properties

NASA Technical Reports Server (NTRS)

Almloef, Jan; Taylor, Peter R.

1989-01-01

A recently proposed scheme for using natural orbitals from atomic configuration interaction (CI) wave functions as a basis set for linear combination of atomic orbitals (LCAO) calculations is extended for the calculation of molecular properties. For one-electron properties like multipole moments, which are determined largely by the outermost regions of the molecular wave function, it is necessary to increase the flexibility of the basis in these regions. This is most easily done by uncontracting the outmost Gaussian primitives, and/or by adding diffuse primitives. A similar approach can be employed for the calculation of polarizabilities. Properties which are not dominated by the long-range part of the wave function, such as spectroscopic constants or electric field gradients at the nucleus, can generally be treated satisfactorily with the original atomic natural orbital (ANO) sets.

A study of interior noise levels, noise sources and transmission paths in light aircraft

NASA Technical Reports Server (NTRS)

Hayden, R. E.; Murray, B. S.; Theobald, M. A.

1983-01-01

The interior noise levels and spectral characteristics of 18 single-and twin-engine propeller-driven light aircraft, and source-path diagnosis of a single-engine aircraft which was considered representative of a large part of the fleet were studied. The purpose of the flight surveys was to measure internal noise levels and identify principal noise sources and paths under a carefully controlled and standardized set of flight procedures. The diagnostic tests consisted of flights and ground tests in which various parts of the aircraft, such as engine mounts, the engine compartment, exhaust pipe, individual panels, and the wing strut were instrumented to determine source levels and transmission path strengths using the transfer function technique. Predominant source and path combinations are identified. Experimental techniques are described. Data, transfer function calculations to derive source-path contributions to the cabin acoustic environment, and implications of the findings for noise control design are analyzed.

A new neolithic circular enclosure in Central Germany

NASA Astrophysics Data System (ADS)

Kretzer, Olaf

2015-08-01

Today we know about 130 neolithic enclosures in Central Europe. About 20 of them are located in Germany. In the last years, there was a great discussion about the function of the openings: Are the openings aligned with points of the solstices? Or are the openings aligned with points of rising stars?Four years ago, a new neolithic circular enclosure was found in the northern part of Thuringia. With a diameter of about 50 meters it was not so large but it was the first evidence of a neolithic culture in Thuringia: the central part of Germany!7000 years ago, people with unknown identity built up three rings with three or four openings.With the help of various measurements we were able to determine in which directions the openings were aligned. We found a link between these directions and very interesting landmarks - an amazing connection between sky and landscape.

Network exploitation using WAMI tracks

NASA Astrophysics Data System (ADS)

Rimey, Ray; Record, Jim; Keefe, Dan; Kennedy, Levi; Cramer, Chris

2011-06-01

Creating and exploiting network models from wide area motion imagery (WAMI) is an important task for intelligence analysis. Tracks of entities observed moving in the WAMI sensor data are extracted, then large numbers of tracks are studied over long time intervals to determine specific locations that are visited (e.g., buildings in an urban environment), what locations are related to other locations, and the function of each location. This paper describes several parts of the network detection/exploitation problem, and summarizes a solution technique for each: (a) Detecting nodes; (b) Detecting links between known nodes; (c) Node attributes to characterize a node; (d) Link attributes to characterize each link; (e) Link structure inferred from node attributes and vice versa; and (f) Decomposing a detected network into smaller networks. Experimental results are presented for each solution technique, and those are used to discuss issues for each problem part and its solution technique.

Exploring patterns of epigenetic information with data mining techniques.

PubMed

Aguiar-Pulido, Vanessa; Seoane, José A; Gestal, Marcos; Dorado, Julián

2013-01-01

Data mining, a part of the Knowledge Discovery in Databases process (KDD), is the process of extracting patterns from large data sets by combining methods from statistics and artificial intelligence with database management. Analyses of epigenetic data have evolved towards genome-wide and high-throughput approaches, thus generating great amounts of data for which data mining is essential. Part of these data may contain patterns of epigenetic information which are mitotically and/or meiotically heritable determining gene expression and cellular differentiation, as well as cellular fate. Epigenetic lesions and genetic mutations are acquired by individuals during their life and accumulate with ageing. Both defects, either together or individually, can result in losing control over cell growth and, thus, causing cancer development. Data mining techniques could be then used to extract the previous patterns. This work reviews some of the most important applications of data mining to epigenetics.

Vector and tensor contributions to the curvature perturbation at second order

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carrilho, Pedro; Malik, Karim A., E-mail: p.gregoriocarrilho@qmul.ac.uk, E-mail: k.malik@qmul.ac.uk

2016-02-01

We derive the evolution equation for the second order curvature perturbation using standard techniques of cosmological perturbation theory. We do this for different definitions of the gauge invariant curvature perturbation, arising from different splits of the spatial metric, and compare the expressions. The results are valid at all scales and include all contributions from scalar, vector and tensor perturbations, as well as anisotropic stress, with all our results written purely in terms of gauge invariant quantities. Taking the large-scale approximation, we find that a conserved quantity exists only if, in addition to the non-adiabatic pressure, the transverse traceless part ofmore » the anisotropic stress tensor is also negligible. We also find that the version of the gauge invariant curvature perturbation which is exactly conserved is the one defined with the determinant of the spatial part of the inverse metric.« less

Part-time physician faculty in a pediatrics department: a study of equity in compensation and academic advancement.

PubMed

Darbar, Mumtaz; Emans, S Jean; Harris, Z Leah; Brown, Nancy J; Scott, Theresa A; Cooper, William O

2011-08-01

To assess equity in compensation and academic advancement in an academic pediatrics department in which a large proportion of the physician faculty hold part-time appointments. The authors analyzed anonymized data from Vanderbilt University School of Medicine Department of Pediatrics databases for physician faculty (faculty with MD or MD/PhD degrees) employed during July 1, 2007 to June 30, 2008. The primary outcomes were total compensation and years at assistant professor rank. They compared compensation and years at junior rank by part-time versus full-time status, controlling for gender, rank, track, years since first appointment as an assistant professor, and clinical productivity. Of the 119 physician faculty in the department, 112 met inclusion criteria. Among those 112 faculty, 23 (21%) were part-time and 89 (79%) were full-time faculty. Part-time faculty were more likely than full-time faculty to be women (74% versus 28%, P < .001) and married (100% versus 84%, P = .042). Analyses accounting for gender, years since first appointment, rank, clinical productivity, and track did not demonstrate significant differences in compensation by part-time versus full-time status. In other adjusted analyses, faculty with part-time appointments spent an average of 2.48 more years as an assistant professor than did faculty with full-time appointments. Overall group differences in total compensation were not apparent in this department, but physician faculty with part-time appointments spent more time at the rank of assistant professor. This study provides a model for determining and analyzing compensation and effort to ensure equity and transparency across faculty.

Incorporating social and cultural significance of large old trees in conservation policy.

PubMed

Blicharska, Malgorzata; Mikusiński, Grzegorz

2014-12-01

In addition to providing key ecological functions, large old trees are a part of a social realm and as such provide numerous social-cultural benefits to people. However, their social and cultural values are often neglected when designing conservation policies and management guidelines. We believe that awareness of large old trees as a part of human identity and cultural heritage is essential when addressing the issue of their decline worldwide. Large old trees provide humans with aesthetic, symbolic, religious, and historic values, as well as concrete tangible benefits, such as leaves, branches, or nuts. In many cultures particularly large trees are treated with reverence. Also, contemporary popular culture utilizes the image of trees as sentient beings and builds on the ancient myths that attribute great powers to large trees. Although the social and cultural role of large old trees is usually not taken into account in conservation, accounting for human-related values of these trees is an important part of conservation policy because it may strengthen conservation by highlighting the potential synergies in protecting ecological and social values. © 2014 Society for Conservation Biology.

Statistical parameters of nonisothermal lower ionospheric plasma in the electrically active mesosphere

NASA Astrophysics Data System (ADS)

Martynenko, S. I.; Rozumenko, V. T.; Tyrnov, O. F.; Manson, A. H.; Meek, C. E.

The large V/m electric fields inherent in the lower mesosphere play an essential role in lower ionospheric electrodynamics. They must be the cause of large variations in the electron temperature and the electron collision frequency and consequently of the transition of the ionospheric plasma in the lower part of the D region into a nonisothermal state. This study is based on the datasets on large mesospheric electric fields collected with the 2.2-MHz radar of the Institute of Space and Atmospheric Studies, University of Saskatchewan, Canada (52°N geographic latitude, 60.4°N geomagnetic latitude), and with the 2.3-MHz radar of the Kharkiv V. Karazin National University, Ukraine (49.6°N geographic latitude, 45.6°N geomagnetic latitude). The statistical analysis of these data is presented by [Meek, C.E., Manson, A.H., Martynenko, S.I., Rozumenko, V.T., Tyrnov, O.F. Remote sensing of mesospheric electric fields using MF radars. J. Atmos. Solar-Terr. Phys. 66, 881-890, 2004. 10.1016/j.jastp.2004.02.002]. The large mesospheric electric fields in the 60-67-km altitude range are experimentally established to follow a Rayleigh distribution in the 0 < E < 2.5 V/m interval. These data have permitted the resulting differential distributions of relative disturbances in the electron temperature, θ, and the effective electron collision frequency, η, to be determined. The most probable θ and η values are found to be in the 1.4-2.2 interval, and hence the nonstationary state of the lower part of the D region needs to be accounted for in studying processes coupling the electrically active mesosphere and the lower ionospheric plasma.

Homogeneous near surface activity distribution by double energy activation for TLA

NASA Astrophysics Data System (ADS)

Takács, S.; Ditrói, F.; Tárkányi, F.

2007-10-01

Thin layer activation (TLA) is a versatile tool for activating thin surface layers in order to study real-time the surface loss by wear, corrosion or erosion processes of the activated parts, without disassembling or stopping running mechanical structures or equipment. The research problem is the determination of the irradiation parameters to produce point-like or large area optimal activity-depth distribution in the sample. Different activity-depth profiles can be produced depending on the type of the investigated material and the nuclear reaction used. To produce activity that is independent of the depth up to a certain depth is desirable when the material removed from the surface by wear, corrosion or erosion can be collected completely. By applying dual energy irradiation the thickness of this quasi-constant activity layer can be increased or the deviation of the activity distribution from a constant value can be minimized. In the main, parts made of metals and alloys are suitable for direct activation, but by using secondary particle implantation the wear of other materials can also be studied in a surface range a few micrometers thick. In most practical cases activation of a point-like spot (several mm2) is enough to monitor the wear, corrosion or erosion, but for special problems relatively large surfaces areas of complicated spatial geometry need to be activated uniformly. Two ways are available for fulfilling this task, (1) production of large area beam spot or scanning the beam over the surface in question from the accelerator side, or (2) a programmed 3D movement of the sample from the target side. Taking into account the large variability of tasks occurring in practice, the latter method was chosen as the routine solution in our cyclotron laboratory.

The scare tactic: do fear appeals predict motivation and exam scores?

PubMed

Putwain, David; Remedios, Richard

2014-12-01

Prior to high-stakes exams, teachers use persuasive messages that highlight to students the possible consequences of failure. Such messages are known as fear appeals. This study examined whether fear appeals relate to self- and non-self-determined motivation and academic performance. Data were collected in 3 waves. Self-report data pertaining to perceived fear appeals were collected in the first wave, self-report data pertaining to self-determined motivation were collected in the second wave, and exam scores were collected in the third wave. An increased frequency of fear appeals and the appraisal of fear appeals as threatening predicted lower self-determined motivation but were largely unrelated to non-self-determined motivation. An increased frequency of fear appeals and the appraisal of fear appeals as threatening predicted lower examination performance that was partly mediated by lower self-determined motivation. These findings support a position derived from self-worth theory that the negative consequences of fear appeals arise from their focus on avoiding failure rather than their focus on extrinsic consequences. We suggest that teachers and instructors need to be aware how seemingly motivational statements can unwittingly promote lower self-determined motivation. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Using vignettes to explore work-based learning: Part 1.

PubMed

Wareing, Mark

This is the first of two articles exploring the use of vignettes as an alternative method of presenting the data arising from interviews. The interviews were carried out as part of research into work-based learning: both articles are based on findings from a hermeneutic phenomenological study into the lived experience of foundation degree mentors and their students-healthcare assistants undertaking a foundation degree in health and social care in order to become assistant practitioners. Part 1 presents a vignette of a notional workplace mentor (Staff Nurse Sophie) that describes her lived experience supporting two equally notional foundation degree students. Sophie's perspective will be a distillation of data arising from interviews with eight workplace mentors, all employed on acute wards within a large NHS hospital trust. The vignette attempts to demonstrate the role of the workplace mentor in the support of work-based learning, and the interprofessional factors that determine the landscape of workplace learning for foundation degree students. The potential of a vignette to assist in a deeper hermeneutic understanding of meanings arising from data will be explored, and the limitations of the approach considered.

Effects of head-slaved navigation and the use of teleports on spatial orientation in virtual environments.

PubMed

Bakker, Niels H; Passenier, Peter O; Werkhoven, Peter J

2003-01-01

The type of navigation interface in a virtual environment (VE)--head slaved or indirect--determines whether or not proprioceptive feedback stimuli are present during movement. In addition, teleports can be used, which do not provide continuous movement but, rather, discontinuously displace the viewpoint over large distances. A two-part experiment was performed. The first part investigated whether head-slaved navigation provides an advantage for spatial learning in a VE. The second part investigated the role of anticipation when using teleports. The results showed that head-slaved navigation has an advantage over indirect navigation for the acquisition of spatial knowledge in a VE. Anticipating the destination of the teleport prevented disorientation after the displacement to a great extent but not completely. The time that was needed for anticipation increased if the teleport involved a rotation of the viewing direction. This research shows the potential added value of using a head-slaved navigation interface--for example, when using VE for training purposes--and provides practical guidelines for the use of teleports in VE applications.

Tobacco control and gender in south-east Asia. Part II: Singapore and Vietnam.

PubMed

Morrow, Martha; Barraclough, Simon

2003-12-01

In the World Health Organization's Western Pacific Region, being born male is the single greatest risk marker for tobacco use. While the literature demonstrates that risks associated with tobacco use may vary according to sex, gender refers to the socially determined roles and responsibilities of men and women, who initiate, continue and quit using tobacco for complex and often different reasons. Cigarette advertising frequently appeals to gender roles. Yet tobacco control policy tends to be gender-blind. Using a broad, gender-sensitivity framework, this contradiction is explored in four Western Pacific countries. Part I of the study presented the rationale, methodology and design of the study, discussed issues surrounding gender and tobacco, and analysed developments in Malaysia and the Philippines (see the previous issue of this journal). Part II deals with Singapore and Vietnam. In all four countries gender was salient for the initiation and maintenance of smoking. Yet, with a few exceptions, gender was largely unrecognized in control policy. Suggestions for overcoming this weakness in order to enhance tobacco control are made.

Photo-physics study of an hydroxy-quinoline derivative as inhibitor of Pim-1 kinase: ultraviolet-visible linear dichroism spectroscopy and quantum chemical calculations.

PubMed

Lamhasni, T; Ait Lyazidi, S; Hnach, M; Haddad, M; Desmaële, D; Spanget-Larsen, J; Nguyen, D D; Ducasse, L

2013-09-01

The photophysical properties of the antiviral 7-nicotinoyl-styrylquinoline (MB96) were investigated by means of UV-Vis linear dichroism (LD) spectroscopy on molecular samples aligned in stretched polyvinylalcohol (PVA), supported by time dependent density functional theory (TD-DFT) calculations. Experimentally, the directions of the transitions moments with respect to the long axis of the molecule were deduced from the orientation K factors, determined by means of "trial-and-error" procedure. The absorption spectrum presents two parts. The main transition in the lowest energy part, observed around 365 nm and showing the highest K value 0.8, is longitudinally in-plane polarized. The highest energy part which is extended between 230 and 320 nm, large, diffuse, and of weak intensity, shows estimated K values between 0.2 and 0.5. This complex structure is transversally polarized with some contamination by the longitudinal character of the first strong band. The TD-DFT results agree fairly well with the LD measurements. Copyright © 2013 Elsevier B.V. All rights reserved.

A Review of Large Solid Rocket Motor Free Field Acoustics, Part I

NASA Technical Reports Server (NTRS)

Pilkey, Debbie; Kenny, Robert Jeremy

2011-01-01

At the ATK facility in Utah, large full scale solid rocket motors are tested. The largest is a five segment version of the Reusable Solid Rocket Motor, which is for use on future launch vehicles. Since 2006, Acoustic measurements have been taken on large solid rocket motors at ATK. Both the four segment RSRM and the five segment RSRMV have been instrumented. Measurements are used to update acoustic prediction models and to correlate against vibration responses of the motor. Presentation focuses on two major sections: Part I) Unique challenges associated with measuring rocket acoustics Part II) Acoustic measurements summary over past five years

49 CFR Appendix C to Part 512 - Early Warning Reporting Class Determinations

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 6 2011-10-01 2011-10-01 false Early Warning Reporting Class Determinations C Appendix C to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL.... 512, App. C Appendix C to Part 512—Early Warning Reporting Class Determinations (a) The Chief Counsel...

49 CFR Appendix C to Part 512 - Early Warning Reporting Class Determinations

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 6 2012-10-01 2012-10-01 false Early Warning Reporting Class Determinations C Appendix C to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL.... 512, App. C Appendix C to Part 512—Early Warning Reporting Class Determinations (a) The Chief Counsel...

49 CFR Appendix C to Part 512 - Early Warning Reporting Class Determinations

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Early Warning Reporting Class Determinations C Appendix C to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL.... 512, App. C Appendix C to Part 512—Early Warning Reporting Class Determinations (a) The Chief Counsel...

49 CFR Appendix C to Part 512 - Early Warning Reporting Class Determinations

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 6 2013-10-01 2013-10-01 false Early Warning Reporting Class Determinations C Appendix C to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL.... 512, App. C Appendix C to Part 512—Early Warning Reporting Class Determinations (a) The Chief Counsel...

49 CFR Appendix C to Part 512 - Early Warning Reporting Class Determinations

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 6 2014-10-01 2014-10-01 false Early Warning Reporting Class Determinations C Appendix C to Part 512 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL.... 512, App. C Appendix C to Part 512—Early Warning Reporting Class Determinations (a) The Chief Counsel...

The NIH Cognitive and Emotional Health Project. Report of the Critical Evaluation Study Committee.

PubMed

Hendrie, Hugh C; Albert, Marilyn S; Butters, Meryl A; Gao, Sujuan; Knopman, David S; Launer, Lenore J; Yaffe, Kristine; Cuthbert, Bruce N; Edwards, Emmeline; Wagster, Molly V

2006-01-01

The Cognitive and Emotional Health Project (CEHP) seeks to identify the demographic, social, and biological determinants of cognitive and emotional health in the older adult. As part of the CEHP, a critical evaluation study committee was formed to assess the state of epidemiological research on demographic, social, and biological determinants of cognitive and emotional health. Criteria for inclusion in the survey were large cohort studies, longitudinal in design, participants predominantly 65 years or older, with measurements of both cognition and emotion, and information on a wide variety of demographic, psychosocial, and biological factors. North American and European studies, which met these criteria, were selected for the review. Outcome measures included cognition, cognitive decline, and cognitive function. For emotion, symptoms included depression and anxiety, positive and negative affect, subjective well being, mastery, and resilience. Ninety-six papers were identified that addressed cognitive and emotional outcomes. A large variety of risk factors were consistently identified with cognitive outcomes, particularly those previously associated with increased risk of cardiovascular disease. There was considerable overlap between risk factors for cognitive and emotional outcomes. This review identifies a large number of lifestyle and health behaviors that alter the risk for maintenance of cognitive and emotional health. Large longitudinal cohort studies are a unique source to explore factors associated with cognitive and emotional health. Secondary analyses of these studies should be encouraged as should the development of standardized questionnaires to measure cognitive and emotional health. Future research in this field should study cognitive and emotional health simultaneously.

The Prevalence and Regional Variation of Major Depressive Disorder Among Patients With Peripheral Arterial Disease in the Medicare Population.

PubMed

Columbo, Jesse A; Stone, David H; Goodney, Philip P; Nolan, Brian W; Stableford, Jennifer A; Brooke, Benjamin S; Powell, Richard J; Finn, Christine T

2016-05-01

Current evidence suggests an association between coronary artery disease and major depressive disorder (MDD). Data to support a similar association between peripheral arterial disease (PAD) and MDD are more limited. This study examines the prevalence and regional variation of both PAD and MDD in a large contemporary patient sample. All Medicare claims, part A and B, from January 2009 until December 2011 were queried using diagnosis codes specific for a previously validated clinical algorithm for PAD and major depression. Codes for PAD included those specific to cerebrovascular disease, abdominal aortic aneurysm, and peripheral vascular disease. Peripheral arterial disease prevalence, major depression prevalence, and coprevalence rates were determined, respectively. Regional variation of both conditions was determined using zip code data to identify potential endemic areas of disease intensity for both diagnoses. Over the study interval, the percentage of Medicare beneficiaries with a diagnosis of PAD remained relatively constant (3.0%-3.7%, n = 0.85-1.06 million in part A and 17.4%-17.5%, n = 4.82-4.93 million in part B), and MDD showed a similar trend (1.6%-2.7%, n = 0.46-0.79 million in part A and 6.1%-6.7%, n = 1.69-1.90 million in part B). The observed rate of MDD in those with an established diagnosis of PAD was 5-fold higher than those without PAD in part A claims (1.8-fold in part B claims). Moreover, there was a significant linear geographic correlation among patients with PAD and MDD (r = .54, P ≤ .01). This study documents a correlation between PAD and MDD and may, therefore, identify an at-risk population susceptible to inferior clinical outcomes. Significant regional variation exists in the prevalence of PAD and MDD, though there appear to be specific endemic regions notable for both disorders. Accordingly, health-care resource allocation toward endemic regions may help improve population health among this at-risk cohort. © The Author(s) 2016.

A new theory for multistep discretizations of stiff ordinary differential equations: Stability with large step sizes

NASA Technical Reports Server (NTRS)

Majda, G.

1985-01-01

A large set of variable coefficient linear systems of ordinary differential equations which possess two different time scales, a slow one and a fast one is considered. A small parameter epsilon characterizes the stiffness of these systems. A system of o.d.e.s. in this set is approximated by a general class of multistep discretizations which includes both one-leg and linear multistep methods. Sufficient conditions are determined under which each solution of a multistep method is uniformly bounded, with a bound which is independent of the stiffness of the system of o.d.e.s., when the step size resolves the slow time scale, but not the fast one. This property is called stability with large step sizes. The theory presented lets one compare properties of one-leg methods and linear multistep methods when they approximate variable coefficient systems of stiff o.d.e.s. In particular, it is shown that one-leg methods have better stability properties with large step sizes than their linear multistep counter parts. The theory also allows one to relate the concept of D-stability to the usual notions of stability and stability domains and to the propagation of errors for multistep methods which use large step sizes.

Ensemble Kalman filters for dynamical systems with unresolved turbulence

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grooms, Ian, E-mail: grooms@cims.nyu.edu; Lee, Yoonsang; Majda, Andrew J.

Ensemble Kalman filters are developed for turbulent dynamical systems where the forecast model does not resolve all the active scales of motion. Coarse-resolution models are intended to predict the large-scale part of the true dynamics, but observations invariably include contributions from both the resolved large scales and the unresolved small scales. The error due to the contribution of unresolved scales to the observations, called ‘representation’ or ‘representativeness’ error, is often included as part of the observation error, in addition to the raw measurement error, when estimating the large-scale part of the system. It is here shown how stochastic superparameterization (amore » multiscale method for subgridscale parameterization) can be used to provide estimates of the statistics of the unresolved scales. In addition, a new framework is developed wherein small-scale statistics can be used to estimate both the resolved and unresolved components of the solution. The one-dimensional test problem from dispersive wave turbulence used here is computationally tractable yet is particularly difficult for filtering because of the non-Gaussian extreme event statistics and substantial small scale turbulence: a shallow energy spectrum proportional to k{sup −5/6} (where k is the wavenumber) results in two-thirds of the climatological variance being carried by the unresolved small scales. Because the unresolved scales contain so much energy, filters that ignore the representation error fail utterly to provide meaningful estimates of the system state. Inclusion of a time-independent climatological estimate of the representation error in a standard framework leads to inaccurate estimates of the large-scale part of the signal; accurate estimates of the large scales are only achieved by using stochastic superparameterization to provide evolving, large-scale dependent predictions of the small-scale statistics. Again, because the unresolved scales contain so much energy, even an accurate estimate of the large-scale part of the system does not provide an accurate estimate of the true state. By providing simultaneous estimates of both the large- and small-scale parts of the solution, the new framework is able to provide accurate estimates of the true system state.« less

Eye size and visual acuity influence vestibular anatomy in mammals.

PubMed

Kemp, Addison D; Christopher Kirk, E

2014-04-01

The semicircular canals of the inner ear detect head rotations and trigger compensatory movements that stabilize gaze and help maintain visual fixation. Mammals with large eyes and high visual acuity require precise gaze stabilization mechanisms because they experience diminished visual functionality at low thresholds of uncompensated motion. Because semicircular canal radius of curvature is a primary determinant of canal sensitivity, species with large canal radii are expected to be capable of more precise gaze stabilization than species with small canal radii. Here, we examine the relationship between mean semicircular canal radius of curvature, eye size, and visual acuity in a large sample of mammals. Our results demonstrate that eye size and visual acuity both explain a significant proportion of the variance in mean canal radius of curvature after statistically controlling for the effects of body mass and phylogeny. These findings suggest that variation in mean semicircular canal radius of curvature among mammals is partly the result of selection for improved gaze stabilization in species with large eyes and acute vision. Our results also provide a possible functional explanation for the small semicircular canal radii of fossorial mammals and plesiadapiforms. Copyright © 2014 Wiley Periodicals, Inc.

Fractional Transport in Strongly Turbulent Plasmas.

PubMed

Isliker, Heinz; Vlahos, Loukas; Constantinescu, Dana

2017-07-28

We analyze statistically the energization of particles in a large scale environment of strong turbulence that is fragmented into a large number of distributed current filaments. The turbulent environment is generated through strongly perturbed, 3D, resistive magnetohydrodynamics simulations, and it emerges naturally from the nonlinear evolution, without a specific reconnection geometry being set up. Based on test-particle simulations, we estimate the transport coefficients in energy space for use in the classical Fokker-Planck (FP) equation, and we show that the latter fails to reproduce the simulation results. The reason is that transport in energy space is highly anomalous (strange), the particles perform Levy flights, and the energy distributions show extended power-law tails. Newly then, we motivate the use and derive the specific form of a fractional transport equation (FTE), we determine its parameters and the order of the fractional derivatives from the simulation data, and we show that the FTE is able to reproduce the high energy part of the simulation data very well. The procedure for determining the FTE parameters also makes clear that it is the analysis of the simulation data that allows us to make the decision whether a classical FP equation or a FTE is appropriate.

Identification of critical equipment and determination of operational limits in helium refrigerators under pulsed heat load

NASA Astrophysics Data System (ADS)

Dutta, Rohan; Ghosh, Parthasarathi; Chowdhury, Kanchan

2014-01-01

Large-scale helium refrigerators are subjected to pulsed heat load from tokamaks. As these plants are designed for constant heat loads, operation under such varying load may lead to instability in plants thereby tripping the operation of different equipment. To understand the behavior of the plant subjected to pulsed heat load, an existing plant of 120 W at 4.2 K and another large-scale plant of 18 kW at 4.2 K have been analyzed using a commercial process simulator Aspen Hysys®. A similar heat load characteristic has been applied in both quasi steady state and dynamic analysis to determine critical stages and equipment of these plants from operational point of view. It has been found that the coldest part of both the cycles consisting JT-stage and its preceding reverse Brayton stage are the most affected stages of the cycles. Further analysis of the above stages and constituting equipment revealed limits of operation with respect to variation of return stream flow rate resulted from such heat load variations. The observations on the outcome of the analysis can be used for devising techniques for steady operation of the plants subjected to pulsed heat load.

Flooding Frequency Alters Vegetation in Isolated Wetlands

USGS Publications Warehouse

Haag, Kim H.; Lee, Terrie M.

2006-01-01

Many isolated wetlands in central Florida occur as small, shallow depressions scattered throughout the karst topography of the region. In these wetlands, the water table approaches land surface seasonally, and water levels and flooding frequency are largely determined by differences between precipitation and evapotranspiration. Because much of the region is flat with little topographic relief, small changes in wetland water levels can cause large changes in wetland surface area. Persistent changes in wetland flooding frequencies, as a result of changes in rainfall or human activity, can cause a substantial change in the vegetation of thousands of acres of land. Understanding the effect that flooding frequency has on wetland vegetation is important to assessing the overall ecological status of wetlands. Wetland bathymetric mapping, when combined with water-level data and vegetation assessments, can enable scientists to determine the frequency of flooding at different elevations in a wetland and describe the effects of flooding frequency on wetland vegetation at those elevations. Five cypress swamps and five marshes were studied by the U.S. Geological Survey (USGS) during 2000-2004, as part of an interdisciplinary study of isolated wetlands in central Florida (Haag and others, 2005). Partial results from two of these marshes are described in this report.

Fractional Transport in Strongly Turbulent Plasmas

NASA Astrophysics Data System (ADS)

Isliker, Heinz; Vlahos, Loukas; Constantinescu, Dana

2017-07-01

We analyze statistically the energization of particles in a large scale environment of strong turbulence that is fragmented into a large number of distributed current filaments. The turbulent environment is generated through strongly perturbed, 3D, resistive magnetohydrodynamics simulations, and it emerges naturally from the nonlinear evolution, without a specific reconnection geometry being set up. Based on test-particle simulations, we estimate the transport coefficients in energy space for use in the classical Fokker-Planck (FP) equation, and we show that the latter fails to reproduce the simulation results. The reason is that transport in energy space is highly anomalous (strange), the particles perform Levy flights, and the energy distributions show extended power-law tails. Newly then, we motivate the use and derive the specific form of a fractional transport equation (FTE), we determine its parameters and the order of the fractional derivatives from the simulation data, and we show that the FTE is able to reproduce the high energy part of the simulation data very well. The procedure for determining the FTE parameters also makes clear that it is the analysis of the simulation data that allows us to make the decision whether a classical FP equation or a FTE is appropriate.

Geometry of a large-scale low-angle mid-crustal thrust (Woodroffe Thrust, Central Australia)

NASA Astrophysics Data System (ADS)

Wex, Sebastian; Mancktelow, Neil S.; Hawemann, Friedrich; Pennacchioni, Giorgio; Camacho, Alfredo

2015-04-01

Young orogens, such as the Alps, mainly expose the upper part of the continental crust and it is not possible to follow large-scale thrusts (e.g. the Glarus Thrust) to great depth in order to study their changing rheological behavior. This knowledge, however, is crucial for determining the overall kinematic and dynamic response during collision, as middle to lower crustal rocks represent the major part of the total crustal section. Information from deeper parts of the continental crust can only be obtained directly by investigating regions where these levels are now exhumed. The Musgrave Ranges in Central Australia is a very well exposed, semi-desert area, in which numerous large-scale shear zones developed during the Petermann Orogeny around 550 Ma. The most prominent structure is the ˜400 km long E-W trending Woodroffe Thrust, which placed ˜1.2 Ga granulites onto similarly-aged amphibolite and granulite facies gneisses along a generally south-dipping thrust plane with a top-to-north shear sense. Geothermobarometric calculations on the associated mylonites established that the structure developed under mid-crustal conditions (500-650°C, 0.8-1 GPa). Regional P/T variations in the direction of thrusting are small, but show trends consistent with the south-dipping orientation of the thrust plane, which predicts deeper levels and a higher metamorphic grade in the south than in the north. They imply a very low gradient of only around 3°C/km for a distance of some 30 km in the movement direction of the thrust. Combined with a geothermal gradient on the order of 20°C/km, calculated from four separate P/T estimates from the hanging wall and footwall, this regional gradient indicates that the Woodroffe Thrust was originally shallow-dipping at an average angle of only around 9°. This suggests that upper crustal brittle thrusts do not necessarily steepen into the middle to lower crust, but can define very shallow-dipping, large-scale planar features, with dimensions in the order of hundreds of kilometres. Such a geometry would require the rocks to be weak, but field observations (e.g. large volumes of syn-tectonic pseudotachylyte) argue for strong behaviour, involving alternating fast (seismic) fracturing and slow (aseismic) creep.

A Variational Assimilation Method for Satellite and Conventional Data: a Revised Basic Model 2B

NASA Technical Reports Server (NTRS)

Achtemeier, Gary L.; Scott, Robert W.; Chen, J.

1991-01-01

A variational objective analysis technique that modifies observations of temperature, height, and wind on the cyclone scale to satisfy the five 'primitive' model forecast equations is presented. This analysis method overcomes all of the problems that hindered previous versions, such as over-determination, time consistency, solution method, and constraint decoupling. A preliminary evaluation of the method shows that it converges rapidly, the divergent part of the wind is strongly coupled in the solution, fields of height and temperature are well-preserved, and derivative quantities such as vorticity and divergence are improved. Problem areas are systematic increases in the horizontal velocity components, and large magnitudes of the local tendencies of the horizontal velocity components. The preliminary evaluation makes note of these problems but detailed evaluations required to determine the origin of these problems await future research.

Experimental Determination of Impurity and Interdiffusion Coefficients in Seven Ti and Zr Binary Systems Using Diffusion Multiples

NASA Astrophysics Data System (ADS)

Chen, Zhangqi; Liu, Zi-Kui; Zhao, Ji-Cheng

2018-05-01

Diffusion coefficients of seven binary systems (Ti-Mo, Ti-Nb, Ti-Ta, Ti-Zr, Zr-Mo, Zr-Nb, and Zr-Ta) at 1200 °C, 1000 °C, and 800 °C were experimentally determined using three Ti-Mo-Nb-Ta-Zr diffusion multiples. Electron probe microanalysis (EPMA) was performed to collect concentration profiles at the binary diffusion regions. Forward simulation analysis (FSA) was then applied to extract both impurity and interdiffusion coefficients in Ti-rich and Zr-rich part of the bcc phase. Excellent agreements between our results and most of the literature data validate the high-throughput approach combining FSA with diffusion multiples to obtain a large amount of systematic diffusion data, which will help establish the diffusion (mobility) databases for the design and development of biomedical and structural Ti alloys.

Experimental Determination of Impurity and Interdiffusion Coefficients in Seven Ti and Zr Binary Systems Using Diffusion Multiples

NASA Astrophysics Data System (ADS)

Chen, Zhangqi; Liu, Zi-Kui; Zhao, Ji-Cheng

2018-07-01

Diffusion coefficients of seven binary systems (Ti-Mo, Ti-Nb, Ti-Ta, Ti-Zr, Zr-Mo, Zr-Nb, and Zr-Ta) at 1200 °C, 1000 °C, and 800 °C were experimentally determined using three Ti-Mo-Nb-Ta-Zr diffusion multiples. Electron probe microanalysis (EPMA) was performed to collect concentration profiles at the binary diffusion regions. Forward simulation analysis (FSA) was then applied to extract both impurity and interdiffusion coefficients in Ti-rich and Zr-rich part of the bcc phase. Excellent agreements between our results and most of the literature data validate the high-throughput approach combining FSA with diffusion multiples to obtain a large amount of systematic diffusion data, which will help establish the diffusion (mobility) databases for the design and development of biomedical and structural Ti alloys.

Effects of impurities in coal-derived liquids on accelerated hot corrosion of superalloys

NASA Technical Reports Server (NTRS)

Deadmore, D. L.; Lowell, C. E.

1980-01-01

A Mach 0.3 burner rig was used to determine the effects of potential coal derived liquid fuel impurity combustion of products on hot corrosion in IN-100, IN-792, IN_738, U-700, Mar M-509, and 304 stainless steel. The impurities, added as aqueous solutions to the combustor, were salts of sodium, potassium, vanadium, molybdenum, tungsten, phosphorus, and lead. Extent of attack was determined by metal consumption and compared to the effects of sodium alone. Vanadium, molybdenum, tungsten, phosphorous, and lead in combination with sodium all resulted in increased attack as compared with sodium alone at some temperatures, apparently due in large part to the extension of the formation of liquid deposits. Varying the sodium-potassium ratio had little effect for ratios less than 1:3 for which reduced, but measurable, attack was observed.

Racial determination of origin of mourning doves in hunters' bags

USGS Publications Warehouse

Aldrich, J.W.; Duvall, A.J.; Geis, A.D.

1958-01-01

A method is described for determining the general area of production of mourning doves that are shot during the hunting season. This procedure is based on the identification of racial characteristics that can be ascertained from samples of wings. The application and utility of this method were demonstrated with data gathered from doves shot in two important dove-hunting areas, Georgia and Texas. The Georgia data indicated that the early-season kill consisted largely of the race carolinensis, while later in the season marginella and the intermediate form made up most of the bag. The wing samples from Texas indicated that birds produced outside of southern Texas made up the largest part of the bag in southern Texas during the entire season. Doves produced west of the Appalachians contributed to both the Georgia and Texas kill.

Muscular Basis of Whisker Torsion in Mice and Rats.

PubMed

Haidarliu, Sebastian; Bagdasarian, Knarik; Shinde, Namrata; Ahissar, Ehud

2017-09-01

Whisking mammals move their whiskers in the rostrocaudal and dorsoventral directions with simultaneous rolling about their long axes (torsion). Whereas muscular control of the first two types of whisker movement was already established, the anatomic muscular substrate of the whisker torsion remains unclear. Specifically, it was not clear whether torsion is induced by asymmetrical operation of known muscles or by other largely unknown muscles. Here, we report that mystacial pads of newborn and adult rats and mice contain oblique intrinsic muscles (OMs) that connect diagonally adjacent vibrissa follicles. Each of the OMs is supplied by a cluster of motor end plates. In rows A and B, OMs connect the ventral part of the rostral follicle with the dorsal part of the caudal follicle. In rows C-E, in contrast, OMs connect the dorsal part of the rostral follicle to the ventral part of the caudal follicle. This inverse architecture is consistent with previous behavioral observations [Knutsen et al.: Neuron 59 (2008) 35-42]. In newborn mice, torsion occurred in irregular single twitches. In adult anesthetized rats, microelectrode mediated electrical stimulation of an individual OM that is coupled with two adjacent whiskers was sufficient to induce a unidirectional torsion of both whiskers. Torsional movement was associated with protracting movement, indicating that in the vibrissal system, like in the ocular system, torsional movement is mechanically coupled to horizontal and vertical movements. This study shows that torsional whisker rotation is mediated by specific OMs whose morphology and attachment sites determine rotation direction and mechanical coupling, and motor innervation determines rotation dynamics. Anat Rec, 300:1643-1653, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Morphological Dependence of Element Stoichiometry in the H. americanus Exoskeleton

NASA Astrophysics Data System (ADS)

Mergelsberg, S. T.; Ulrich, R. N.; Dove, P. M.

2016-02-01

The crustacean exoskeleton is a complex biocomposite of inorganic mineral and organic macromolecules that expresses highly divergent morphologies across different taxa. While the structures and compositions of the organic framework show complex links to environmental and developmental pressures, little is known about the mineral chemistry. Previous studies of the cuticle have assumed that magnesium, phosphorous, and other trace metals are largely contained in the inorganic mineral fraction. Due to analytical limitations of structural analyses and in situ spectroscopic methods, the stoichiometry of the organic and inorganic portions could not be resolved. For example, previous Raman and XRD studies conclude the higher concentrations of trace elements, such as P and Mg measured in reinforced structures, e.g. the claw and abdomen, are primarily determined by the mineral fraction. Using the American Lobster (Homarus americanus) as a model organism to establish relationships between body part function and cuticle composition, this study quantified the distributions of Mg and P in the mineral and organic fractions. The experiments were designed to dissolve the exoskeleton of 10 body parts using three types of solutions that were specific to extracting 1) the mineral phase, 2) protein, and 3) polysaccharide. Analysis of the solutions by ICP-OES shows the mineral phase contains magnesium and phosphorous at concentrations sufficient to support the formation of calcium-magnesium and phosphate minerals. The protein fraction of the body parts contains significantly more Mg and P than previously hypothesized, while the levels of P contained in the organic portion are fairly constant. The findings demonstrate the lobster cuticle contains a significant amount of non-mineralized P and Mg that is readily water-soluble in the protein component. However, for those body parts used for defense and food acquisition, such as the claw, the mineral component determines the overall composition of the exoskeleton.

Hearing in Laboratory Animals: Strain Differences and Nonauditory Effects of Noise

PubMed Central

Parrish, Jennifer L.; Hughes, Larry F.; Toth, Linda A.; Caspary, Donald M.

2013-01-01

Hearing in laboratory animals is a topic that traditionally has been the domain of the auditory researcher. However, hearing loss and exposure to various environmental sounds can lead to changes in multiple organ systems, making what laboratory animals hear of consequence for researchers beyond those solely interested in hearing. For example, several inbred mouse strains commonly used in biomedical research (e.g., C57BL/6, DBA/2, and BALB/c) experience a genetically determined, progressive hearing loss that can lead to secondary changes in systems ranging from brain neurochemistry to social behavior. Both researchers and laboratory animal facility personnel should be aware of both strain and species differences in hearing in order to minimize potentially confounding variables in their research and to aid in the interpretation of data. Independent of genetic differences, acoustic noise levels in laboratory animal facilities can have considerable effects on the inhabitants. A large body of literature describes the nonauditory impact of noise on the biology and behavior of various strains and species of laboratory animals. The broad systemic effects of noise exposure include changes in endocrine and cardiovascular function, sleep–wake cycle disturbances, seizure susceptibility, and an array of behavioral changes. These changes are determined partly by species and strain; partly by noise intensity level, duration, predictability, and other characteristics of the sound; and partly by animal history and exposure context. This article reviews some of the basic strain and species differences in hearing and outlines how the acoustic environment affects different mammals. PMID:15766204

Compound-specific carbon and hydrogen isotope analysis of sub-parts per billion level waterborne petroleum hydrocarbons

USGS Publications Warehouse

Wang, Y.; Huang, Y.; Huckins, J.N.; Petty, J.D.

2004-01-01

Compound-specific carbon and hydrogen isotope analysis (CSCIA and CSHIA) has been increasingly used to study the source, transport, and bioremediation of organic contaminants such as petroleum hydrocarbons. In natural aquatic systems, dissolved contaminants represent the bioavailable fraction that generally is of the greatest toxicological significance. However, determining the isotopic ratios of waterborne hydrophobic contaminants in natural waters is very challenging because of their extremely low concentrations (often at sub-parts ber billion, or even lower). To acquire sufficient quantities of polycyclic aromatic hydrocarbons with 10 ng/L concentration for CSHIA, more than 1000 L of water must be extracted. Conventional liquid/liquid or solid-phase extraction is not suitable for such large volume extractions. We have developed a new approach that is capable of efficiently sampling sub-parts per billion level waterborne petroleum hydrocarbons for CSIA. We use semipermeable membrane devices (SPMDs) to accumulate hydrophobic contaminants from polluted waters and then recover the compounds in the laboratory for CSIA. In this study, we demonstrate, under a variety of experimental conditions (different concentrations, temperatures, and turbulence levels), that SPMD-associated processes do not induce C and H isotopic fractionations. The applicability of SPMD-CSIA technology to natural systems is further demonstrated by determining the ??13C and ??D values of petroleum hydrocarbons present in the Pawtuxet River, RI. Our results show that the combined SPMD-CSIA is an effective tool to investigate the source and fate of hydrophobic contaminants in the aquatic environments.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grate, Jay W.; Bliss, Mary; Farmer, Orville T.

Ultra low-background radiation measurements are essential to several large-scale physics investigations, such as those involving neutrinoless double-beta decay, dark matter detection (such as SuperCDMS), and solar neutrino detection. There is a need for electrically and thermally insulating dielectric materials with extremely low-background radioactivity for detector construction. This need is best met with plastics. Most currently available structural plastics have milliBecquerel-per-kilogram total intrinsic radioactivity. Modern low-level detection systems require a large variety of plastics with low microBecquerel-per-kilogram levels. However, the assay of polymer materials for extremely low levels of radioactive elements, uranium and thorium in particular, presents new challenges. It ismore » only recently that any certified reference materials (CRMs) for toxic metals such as lead or cadmium in plastics have become available. However, there are no CRMs for uranium or thorium in thermoplastics. This paper discusses our assessment of the use of laser ablation (LA) for sampling and inductively coupled plasma mass spectrometry (ICP-MS) for analysis of polyethylene (PE) samples, with an emphasis on uranium determination. Using a CRM for lead in PE, we examine LA and ICP-MS parameters that determine whether the total atom efficiencies for uranium and lead are similar, and explore methods to use the lead content in a plastic as part of the process of estimating or determining the uranium content by LA-ICP-MS.« less

Leaders Leading and Learning (Part 1)

ERIC Educational Resources Information Center

Hannay, Lynne M.; Manning, Michael; Earl, Sandra; Blair, Don

2006-01-01

Internationally, large scale reform is big business and yet relatively little is known about the senior administrators who manage and lead local educational reform implementation. In this first of a two-part article, the authors focus on the role of senior administrators in facilitating large-scale reform in one Ontario, Canada school district…

17 CFR Appendix B to Part 420 - Sample Large Position Report

Code of Federal Regulations, 2010 CFR

2010-04-01

..., and as collateral for financial derivatives and other securities transactions $ Total Memorandum 1... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Sample Large Position Report B Appendix B to Part 420 Commodity and Securities Exchanges DEPARTMENT OF THE TREASURY REGULATIONS UNDER...

Geohydrology of volcanic tuff penetrated by test well UE-25b#1, Yucca Mountain, Nye County, Nevada

USGS Publications Warehouse

Lahoud, R.G.; Lobmeyer, D.H.; Whitfield, M.S.

1984-01-01

Test well UE-25bNo1, located on the east side of Yucca Mountain in the southwestern part of the Nevada Test Site, was drilled to a total depth of 1,220 meters and hydraulically tested as part of a program to evaluate the suitability of Yucca Mountain as a nuclear-waste repository. The well penetrated almost 46 meters of alluvium and 1,174 meters of Tertiary volcanic tuffs. The composite hydraulic head for aquifers penetrated by the well was 728.9 meters above sea level (471.4 meters below land surface) with a slight decrease in loss of hydraulic head with depth. Average hydraulic conductivities for stratigraphic units determined from pumping tests, borehole-flow surveys, and packer-injection tests ranged from less than 0.001 meter per day for the Tram Member of the Crater Flat Tuff to 1.1 meters per day for the Bullfrog Member of the Crater Flat Tuff. The small values represented matrix permeability of unfractured rock; the large values probably resulted from fracture permeability. Chemical analyses indicated that the water is a soft sodium bicarbonate type, slightly alkaline, with large concentrations of dissolved silica and sulfate. Uncorrected carbon-14 age dates of the water were 14,100 and 13,400 years. (USGS)

Cosmonumerology, Cosmophysics, and the Large Numbers Hypothesis: British Cosmology in the 1930s

NASA Astrophysics Data System (ADS)

Durham, Ian

2001-04-01

A number of unorthodox cosmological models were developed in the 1930s, many by British theoreticians. Three of the most notable of these theories included Eddington's cosmonumerology, Milne's cosmophysics, and Dirac's large numbers hypothesis (LNH). Dirac's LNH was based partly on the other two and it has been argued that modern steady-state theories are based partly on Milne's cosmophysics. But what influenced Eddington and Milne? Both were products of the late Victorian education system in Britain and could conceivably have been influenced by Victorian thought which, in addition to its strict (though technically unoffical) social caste system, had a flair for the unusual. Victorianism was filled with a fascination for the occult and the supernatural, and science was not insulated from this trend (witness the Henry Slade trial in 1877). It is conceivable that the normally strict mentality of the scientific process in the minds of Eddington and Milne was affected, indirectly, by this trend for the unusual, possibly pushing them into thinking "outside the box" as it were. In addition, cosmonumerology and the LNH exhibit signs of Pythagorean and Aristotelian thought. It is the aim of this ongoing project at St. Andrews to determine the influences and characterize the relations existing in and within these and related theories.

Australia's National Mental Health Strategy and deinstitutionalization: some empirical results.

PubMed

Doessel, Darrel P; Scheurer, Roman W; Chant, David C; Whiteford, Harvey A

2005-01-01

To determine the role of the National Mental Health Strategy in the deinstitutionalization of patients in psychiatric hospitals in Queensland. Regression analysis (using the maximum likelihood method) has been applied to relevant time-series datasets on public psychiatric institutions in Queensland. In particular, data on both patients and admissions per 10 000 population are analysed in detail from 1953-54 to the present, although data are presented from 1883-84. These Queensland data indicate that deinstitutionalization was a continuing process from the 1950s to the present. However, it is clear that the experience varied from period to period. For example, the fastest change (in both patients and admissions) took place in the period 1953-54 to 1973-74, followed by the period 1974-75 to 1984-85. In large part, the two policies associated with deinstitutionalization, namely a discharge policy ('opening the back door') and an admission policy ('closing the front door') had been implemented before the advent of the National Mental Health Strategy in January 1993. Deinstitutionalization was most rapid in the 30-year period to the early 1980s: the process continued in the 1990s, but at a much slower rate. Deinstitutionalization was, in large part, over before the Strategy was developed and implemented.

Measuring flows in the solar interior: current developments, results, and outstanding problems

NASA Astrophysics Data System (ADS)

Schad, Ariane

2016-10-01

I will present an overview of the current developments to determine flows in the solar interior and recent results from helioseismology. I will lay special focus on the inference of the deep structure of the meridional flow, which is one of the most challenging problems in helioseismology. In recent times, promising approaches have been developed for solving this problem. The time-distance analysis made large improvements in this after becoming aware of and compensating for a systematic effect in the analysis, the origin of which is not clear yet. In addition to this, a different approach is now available, which directly exploits the distortion of mode eigenfunctions by the meridional flow as well as rotation. These methods have presented us partly surprisingly complex meridional flow patterns, which, however, do not provide a consistent picture of the flow. Resolving this puzzle is part of current research since this has important consequences on our understanding of the solar dynamo. Another interesting discrepancy was found in recent studies between the amplitudes of the large- and small-scale dynamics in the convection zone estimated from helioseismology and those predicted from theoretical models. This raises fundamental questions how the Sun, and in general a star, maintains its heat transport and redistributes its angular momentum that lead, e.g., to the observed differential rotation.

Time drawings: Spatial representation of temporal concepts.

PubMed

Leone, María Juliana; Salles, Alejo; Pulver, Alejandro; Golombek, Diego Andrés; Sigman, Mariano

2018-03-01

Time representation is a fundamental property of human cognition. Ample evidence shows that time (and numbers) are represented in space. However, how the conceptual mapping varies across individuals, scales, and temporal structures remains largely unknown. To investigate this issue, we conducted a large online study consisting in five experiments that addressed different time scales and topology: Zones of time, Seasons, Days of the week, Parts of the day and Timeline. Participants were asked to map different kinds of time events to a location in space and to determine their size and color. Results showed that time is organized in space in a hierarchical progression: some features appear to be universal (i.e. selection order), others are shaped by how time is organized in distinct cultures (i.e. location order) and, finally, some aspects vary depending on individual features such as age, gender, and chronotype (i.e. size and color). Copyright © 2018 Elsevier Inc. All rights reserved.

Mother Nature versus human nature: public compliance with evacuation and quarantine.

PubMed

Manuell, Mary-Elise; Cukor, Jeffrey

2011-04-01

Effectively controlling the spread of contagious illnesses has become a critical focus of disaster planning. It is likely that quarantine will be a key part of the overall public health strategy utilised during a pandemic, an act of bioterrorism or other emergencies involving contagious agents. While the United States lacks recent experience of large-scale quarantines, it has considerable accumulated experience of large-scale evacuations. Risk perception, life circumstance, work-related issues, and the opinions of influential family, friends and credible public spokespersons all play a role in determining compliance with an evacuation order. Although the comparison is not reported elsewhere to our knowledge, this review of the principal factors affecting compliance with evacuations demonstrates many similarities with those likely to occur during a quarantine. Accurate identification and understanding of barriers to compliance allows for improved planning to protect the public more effectively. © 2011 The Author(s). Disasters © Overseas Development Institute, 2011.

Undergraduate mathematics students' reasons for attending live lectures when recordings are available

NASA Astrophysics Data System (ADS)

Yoon, Caroline; Oates, Greg; Sneddon, Jamie

2014-02-01

With the proliferation of new affordable recording technologies, many universities have begun offering students recordings of live lectures as a part of the course resources. We conducted a survey to investigate why some students choose to attend lectures in person rather than simply watching the recordings online, and how students view the two types of lectures. Students attending live lectures in five large undergraduate mathematics lecture streams were invited to respond to the survey. A significant number of respondents viewed recorded lecture as superfluous to their needs which were met upon attending live lecture. Surprisingly, however, an equally large number of students described compelling reasons for watching both live and recorded lectures. A number of factors were identified as determining students' perceptions of live and recorded lectures as competing or complementary: personal learning styles, study habits, esteem for the lecturer, and the possibility of interaction in the lecture.

Drag and Propulsive Characteristics of Air-Cooled Engine-Nacelle Installations for Large Airplanes, Special Report

NASA Technical Reports Server (NTRS)

Silverstein, Abe; Wilson, Herbert A., Jr.

1939-01-01

An investigation is in progress in the NACA full-scale wind tunnel to determine the drag and propulsive efficiency of nacelle sizes. In contrast with the usual tests with a single nacelle, these tests were conducted with nacelle-propeller installations on a large model of a 4-engine airplane. Data are presented on the first part of the investigation, covering seven nacelle arrangements with nacelle diameters from 0.53 to 1.5 times the wing thickness. These ratios are similar to those occurring on airplane weighing from about 20 to 100 tons. The results show that the drag, the propulsive efficiency, and the overall efficiency of the various nacelle arrangements as functions of the nacelle size, the propeller position, and the airplane lift coefficient. The effect of the nacelles on the aerodynamic characteristics of the model are shown for both propeller-removed and propeller-operating conditions.

Band gap of corundumlike α -Ga2O3 determined by absorption and ellipsometry

NASA Astrophysics Data System (ADS)

Segura, A.; Artús, L.; Cuscó, R.; Goldhahn, R.; Feneberg, M.

2017-07-01

The electronic structure near the band gap of the corundumlike α phase of Ga2O3 has been investigated by means of optical absorption and spectroscopic ellipsometry measurements in the ultraviolet (UV) range (400-190 nm). The absorption coefficient in the UV region and the imaginary part of the dielectric function exhibit two prominent absorption thresholds with wide but well-defined structures at 5.6 and 6.3 eV which have been ascribed to allowed direct transitions from crystal-field split valence bands to the conduction band. Excitonic effects with large Gaussian broadening are taken into account through the Elliott-Toyozawa model, which yields an exciton binding energy of 110 meV and direct band gaps of 5.61 and 6.44 eV. The large broadening of the absorption onset is related to the slightly indirect character of the material.

A conceptual study of the rotor systems research aircraft

NASA Technical Reports Server (NTRS)

1972-01-01

The analytical comparison of the two candidate Rotor Systems Research Aircraft (RSRA) configurations selected by the Government at the completion of Part 1 of the RSRA Conceptual Predesign Study is presented. The purpose of the comparison was to determine the relative suitability of both vehicles for the RSRA missions described in the Government Statement of Work, and to assess their versatility in the testing of new rotor concepts. The analytical comparison was performed primarily with regard to performance and stability and control. A weights, center-of-gravity, and inertia computation was performed for each iteration in the analysis process. The dynamics investigation was not concerned so much with a comparison of the two vehicles, but explored the dynamic problems attending operation of any RSRA operating with large rotor RPM and diameter ranges over large forward speed ranges. Several means of isolating in- and out-of-plane rotor vibrations were analyzed. An optimum isolation scheme was selected.

General circulation of the South Atlantic between 5 deg N and 35 deg S

NASA Technical Reports Server (NTRS)

Ollitrault, Michel; Mercier, H.; Blanc, F.; Letraon, L. Y.

1991-01-01

The TOPEX/POSEIDON altimeter will provide the temporal mean seal level. So, secondly, we propose to compute the difference between these two surfaces (mean sea level minus general circulation dynamic topography). The result will be an estimate of the marine geoid, which is time invariant for the 5-year period under consideration. If this geoid is precise enough, it will permit a description of seasonal variability of the large-scale surface circulation. If there happens to be enough float data, it may be possible to infer the first vertical modes of this variability. Thus the main goal of our investigation is to determine the 3-D general circulation of the South Atlantic and the large-scale seasonal fluctuations. This last objective, however, may be restricted to the western part of the South Atlantic because float deployments have been scheduled only in the Brasil basin.

Geodetic methods to determine the relativistic redshift at the level of 10^{-18} in the context of international timescales: a review and practical results

NASA Astrophysics Data System (ADS)

Denker, Heiner; Timmen, Ludger; Voigt, Christian; Weyers, Stefan; Peik, Ekkehard; Margolis, Helen S.; Delva, Pacôme; Wolf, Peter; Petit, Gérard

2017-12-01

The frequency stability and uncertainty of the latest generation of optical atomic clocks is now approaching the one part in 10^{18} level. Comparisons between earthbound clocks at rest must account for the relativistic redshift of the clock frequencies, which is proportional to the corresponding gravity (gravitational plus centrifugal) potential difference. For contributions to international timescales, the relativistic redshift correction must be computed with respect to a conventional zero potential value in order to be consistent with the definition of Terrestrial Time. To benefit fully from the uncertainty of the optical clocks, the gravity potential must be determined with an accuracy of about 0.1 m2 s^{-2} , equivalent to about 0.01 m in height. This contribution focuses on the static part of the gravity field, assuming that temporal variations are accounted for separately by appropriate reductions. Two geodetic approaches are investigated for the derivation of gravity potential values: geometric levelling and the Global Navigation Satellite Systems (GNSS)/geoid approach. Geometric levelling gives potential differences with millimetre uncertainty over shorter distances (several kilometres), but is susceptible to systematic errors at the decimetre level over large distances. The GNSS/geoid approach gives absolute gravity potential values, but with an uncertainty corresponding to about 2 cm in height. For large distances, the GNSS/geoid approach should therefore be better than geometric levelling. This is demonstrated by the results from practical investigations related to three clock sites in Germany and one in France. The estimated uncertainty for the relativistic redshift correction at each site is about 2 × 10^{-18}.

Estimation of the interference coupling into cables within electrically large multiroom structures

NASA Astrophysics Data System (ADS)

Keghie, J.; Kanyou Nana, R.; Schetelig, B.; Potthast, S.; Dickmann, S.

2010-10-01

Communication cables are used to transfer data between components of a system. As a part of the EMC analysis of complex systems, it is necessary to determine which level of interference can be expected at the input of connected devices due to the coupling into the irradiated cable. For electrically large systems consisting of several rooms with cables connecting components located in different rooms, an estimation of the coupled disturbances inside cables using commercial field computation software is often not feasible without several restrictions. In many cases, this is related to the non-availability of computing memory and processing power needed for the computation. In this paper, we are going to show that, starting from a topological analysis of the entire system, weak coupling paths within the system can be can be identified. By neglecting these coupling paths and using the transmission line approach, the original system will be simplified so that a simpler estimation is possible. Using the example of a system which is composed of two rooms, multiple apertures, and a network cable located in both chambers, it is shown that an estimation of the coupled disturbances due to external electromagnetic sources is feasible with this approach. Starting from an incident electromagnetic field, we determine transfer functions describing the coupling means (apertures, cables). Using these transfer functions and the knowledge of the weak coupling paths above, a decision is taken regarding the means for paths that can be neglected during the estimation. The estimation of the coupling into the cable is then made while taking only paths with strong coupling into account. The remaining part of the wiring harness in areas with weak coupling is represented by its input impedance. A comparison with the original network shows a good agreement.

Effect of Helical Slow-Wave Circuit Variations on TWT Cold-Test Characteristics

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Dayton, J. A., Jr.

1998-01-01

Recent advances in the state of the art of computer modeling offer the possibility for the first time to evaluate the effect that slow-wave structure parameter variations, such as manufacturing tolerances, have on the cold-test characteristics of helical traveling-wave tubes (TWT's). This will enable manufacturers to determine the cost effectiveness of controlling the dimensions of the component parts of the TWT, which is almost impossible to do experimentally without building a large number of tubes and controlling several parameters simultaneously. The computer code MAFIA is used in this analysis to determine the effect on dispersion and on-axis interaction impedance of several helical slow-wave circuit parameter variations, including thickness and relative dielectric constant of the support rods, tape width, and height of the metallized films deposited on the dielectric rods. Previous computer analyzes required so many approximations that accurate determinations of the effect of many relevant dimensions on tube performance were practically impossible.

Effect of Helical Slow-Wave Circuit Variations on TWT Cold-Test Characteristics

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Dayton, James A., Jr.

1997-01-01

Recent advances in the state of the art of computer modeling offer the possibility for the first time to evaluate the effect that slow-wave structure parameter variations, such as manufacturing tolerances, have on the cold-test characteristics of helical traveling-wave tubes (TWT's). This will enable manufacturers to determine the cost effectiveness of controlling the dimensions of the component parts of the TWT, which is almost impossible to do experimentally without building a large number of tubes and controlling several parameters simultaneously. The computer code MAFIA is used in this analysis to determine the effect on dispersion and on-axis interaction impedance of several helical slow-wave circuit parameter variations, including thickness and relative dielectric constant of the support rods, tape width, and height of the metallized films deposited on the dielectric rods. Previous computer analyses required so many approximations that accurate determinations of the effect of many relevant dimensions on tube performance were practically impossible.

Effect of Helical Slow-Wave Circuit Variations on TWT Cold-Test Characteristics

NASA Technical Reports Server (NTRS)

Kory, Carol L.; Dayton, James A., Jr.

1998-01-01

Recent advances in the state of the art of computer modeling offer the possibility for the first time to evaluate the effect that slow-wave structure parameter variations, such'as manufacturing tolerances, have on the cold-test characteristics of helical traveling-wave tubes (TWT's). This will enable manufacturers to determine the cost effectiveness of controlling the dimensions of the component parts of the TWT, which is almost impossible to do experimentally without building a large number of tubes and controlling several parameters simultaneously. The computer code MAxwell's equations by the Finite Integration Algorithm (MAFIA) is used in this analysis to determine the effect on dispersion and on-axis interaction impedance of several helical slow-wave circuit parameter variations, including thickness and relative dielectric constant of the support rods, tape width, and height of the metallized films deposited on the dielectric rods. Previous computer analyzes required so many approximations that accurate determinations of the effect of many relevant dimensions on tube performance were practically impossible.

Knowledge and perceptions about aging and frailty: An integrative review of the literature.

PubMed

Parish, Abby; Kim, Jennifer; Lewallen, Kanah May; Miller, Sally; Myers, Janet; Panepinto, Robbie; Maxwell, Cathy A

2018-06-14

A growing body of evidence indicates that biological aging or frailty is a determinant of health-related outcomes, however, frailty is likely poorly understood and under-recognized by the public-at-large. Using Whittemore and Knafl's methodology, we aimed to conduct an integrative review of research on public knowledge and perceptions of aging and frailty, and to create a conceptual model of our findings. Twenty-three studies are presented. The conceptual model suggests that culture, knowledge of aging, and stereotypes influence adults' beliefs and perceptions. Adults determine priorities about aging, and then subconsciously or consciously determine which parts of are controllable. If deemed controllable and important, they may participate in health behaviors to mediate aging. If deemed uncontrollable or less important, adults may aim to control their own peace of mind through acceptance. Scant findings suggest that frailty is a more subjective term in which participants often optimistically do not identify themselves as frail. Copyright © 2018 Elsevier Inc. All rights reserved.

Application of genetic algorithms to focal mechanism determination

NASA Astrophysics Data System (ADS)

Kobayashi, Reiji; Nakanishi, Ichiro

1994-04-01

Genetic algorithms are a new class of methods for global optimization. They resemble Monte Carlo techniques, but search for solutions more efficiently than uniform Monte Carlo sampling. In the field of geophysics, genetic algorithms have recently been used to solve some non-linear inverse problems (e.g., earthquake location, waveform inversion, migration velocity estimation). We present an application of genetic algorithms to focal mechanism determination from first-motion polarities of P-waves and apply our method to two recent large events, the Kushiro-oki earthquake of January 15, 1993 and the SW Hokkaido (Japan Sea) earthquake of July 12, 1993. Initial solution and curvature information of the objective function that gradient methods need are not required in our approach. Moreover globally optimal solutions can be efficiently obtained. Calculation of polarities based on double-couple models is the most time-consuming part of the source mechanism determination. The amount of calculations required by the method designed in this study is much less than that of previous grid search methods.

Determination of the spin Hall angle in single-crystalline Pt films from spin pumping experiments

NASA Astrophysics Data System (ADS)

Keller, Sascha; Mihalceanu, Laura; Schweizer, Matthias R.; Lang, Philipp; Heinz, Björn; Geilen, Moritz; Brächer, Thomas; Pirro, Philipp; Meyer, Thomas; Conca, Andres; Karfaridis, Dimitrios; Vourlias, George; Kehagias, Thomas; Hillebrands, Burkard; Papaioannou, Evangelos Th

2018-05-01

We report on the determination of the spin Hall angle in ultra-clean, defect-reduced epitaxial Pt films. By applying vector network analyzer ferromagnetic resonance spectroscopy to a series of single crystalline Fe (12 nm) /Pt (t Pt) bilayers we determine the real part of the spin mixing conductance (4.4 ± 0.2) × 1019 m‑2 and reveal a very small spin diffusion length in the epitaxial Pt (1.1 ± 0.1) nm film. We investigate the spin pumping and ISHE in a stripe microstucture excited by a microwave coplanar waveguide antenna. By using their different angular dependencies, we distinguish between spin rectification effects and the inverse spin Hall effect. The relatively large value of the spin Hall angle (5.7 ± 1.4)% shows that ultra-clean e-beam evaporated non-magnetic materials can also have a comparable spin-to-charge current conversion efficiency as sputtered high resistivity layers.

In-Situ Printing of Conductive Polylactic Acid (cPLA) Strain Sensors Embedded into Additively Manufactured Parts using Fused Deposition Modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ouellette, Brittany Joy

Additive Manufacturing (AM) technology has been around for decades, but until recently, machines have been expensive, relatively large, and not available to most institutions. Increased technological advances in 3D printing and awareness throughout industry, universities, and even hobbyists has increased demand to substitute AM parts in place of traditionally manufactured (subtractive) designs; however, there is a large variability of part quality and mechanical behavior due to the inherent printing process, which must be understood before AM parts are used for load bearing and structural design.

23 CFR Appendix E to Part 1240 - Determination of Federal Medical Savings

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Determination of Federal Medical Savings E Appendix E to Part 1240 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL HIGHWAY ADMINISTRATION... SEAT BELT USE RATES Pt. 1240, App. E Appendix E to Part 1240—Determination of Federal Medical Savings A...

33 CFR Appendix C to Part 331 - Administrative Appeal Process for Approved Jurisdictional Determinations

Code of Federal Regulations, 2011 CFR

2011-07-01

... Approved Jurisdictional Determinations C Appendix C to Part 331 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE ADMINISTRATIVE APPEAL PROCESS Pt. 331, App. C Appendix C to Part 331—Administrative Appeal Process for Approved Jurisdictional Determinations ER28MR00...

33 CFR Appendix C to Part 331 - Administrative Appeal Process for Approved Jurisdictional Determinations

Code of Federal Regulations, 2013 CFR

2013-07-01

... Approved Jurisdictional Determinations C Appendix C to Part 331 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE ADMINISTRATIVE APPEAL PROCESS Pt. 331, App. C Appendix C to Part 331—Administrative Appeal Process for Approved Jurisdictional Determinations ER28MR00...

33 CFR Appendix C to Part 331 - Administrative Appeal Process for Approved Jurisdictional Determinations

Code of Federal Regulations, 2012 CFR

2012-07-01

... Approved Jurisdictional Determinations C Appendix C to Part 331 Navigation and Navigable Waters CORPS OF ENGINEERS, DEPARTMENT OF THE ARMY, DEPARTMENT OF DEFENSE ADMINISTRATIVE APPEAL PROCESS Pt. 331, App. C Appendix C to Part 331—Administrative Appeal Process for Approved Jurisdictional Determinations ER28MR00...

Effects of fat on glucose uptake and utilization in patients with non-insulin-dependent diabetes.

PubMed Central

Boden, G; Chen, X

1995-01-01

It was the aim of this study to determine whether FFA inhibit insulin-stimulated whole body glucose uptake and utilization in patients with non-insulin-dependent diabetes. We performed five types of isoglycemic (approximately 11mM) clamps: (a) with insulin; (b) with insulin plus fat/heparin; (c) with insulin plus glycerol; (d) with saline; (e) with saline plus fat/heparin and two types of euglycemic (approximately 5mM) clamps: (a) with insulin; (b) with insulin plus fat/heparin. During these studies, we determined rates of glucose uptake, glycolysis (both with 3[3H] glucose), glycogen synthesis (determined as glucose uptake minus glycolysis), carbohydrate oxidation (by indirect calorimetry) and nonoxidative glycolysis (determined as glycolysis minus carbohydrate oxidation). Fat/heparin infusion did not affect basal glucose uptake, but inhibited total stimulated (insulin stimulated plus basal) glucose uptake by 40-50% in isoglycemic and in euglycemic patients at plasma FFA concentration of approximately 950 and approximately 550 microM, respectively. In isoglycemic patients, the 40-50% inhibition of total stimulated glucose uptake was due to near complete inhibition of the insulin-stimulated part of glucose uptake. Proportional inhibition of glucose uptake, glycogen synthesis, and glycolysis suggested a major FFA-mediated defect involving glucose transport and/or phosphorylation. In summary, fat produced proportional inhibitions of insulin-stimulated glucose uptake and of intracellular glucose utilization. We conclude, that physiologically elevated levels of FFa could potentially be responsible for a large part of the peripheral insulin resistance in patients with non-insulin-dependent diabetes mellitus. PMID:7657800

Effects of fat on glucose uptake and utilization in patients with non-insulin-dependent diabetes.

PubMed

Boden, G; Chen, X

1995-09-01

It was the aim of this study to determine whether FFA inhibit insulin-stimulated whole body glucose uptake and utilization in patients with non-insulin-dependent diabetes. We performed five types of isoglycemic (approximately 11mM) clamps: (a) with insulin; (b) with insulin plus fat/heparin; (c) with insulin plus glycerol; (d) with saline; (e) with saline plus fat/heparin and two types of euglycemic (approximately 5mM) clamps: (a) with insulin; (b) with insulin plus fat/heparin. During these studies, we determined rates of glucose uptake, glycolysis (both with 3[3H] glucose), glycogen synthesis (determined as glucose uptake minus glycolysis), carbohydrate oxidation (by indirect calorimetry) and nonoxidative glycolysis (determined as glycolysis minus carbohydrate oxidation). Fat/heparin infusion did not affect basal glucose uptake, but inhibited total stimulated (insulin stimulated plus basal) glucose uptake by 40-50% in isoglycemic and in euglycemic patients at plasma FFA concentration of approximately 950 and approximately 550 microM, respectively. In isoglycemic patients, the 40-50% inhibition of total stimulated glucose uptake was due to near complete inhibition of the insulin-stimulated part of glucose uptake. Proportional inhibition of glucose uptake, glycogen synthesis, and glycolysis suggested a major FFA-mediated defect involving glucose transport and/or phosphorylation. In summary, fat produced proportional inhibitions of insulin-stimulated glucose uptake and of intracellular glucose utilization. We conclude, that physiologically elevated levels of FFa could potentially be responsible for a large part of the peripheral insulin resistance in patients with non-insulin-dependent diabetes mellitus.

Transducer-actuator systems and methods for performing on-machine measurements and automatic part alignment

DOEpatents

Barkman, William E.; Dow, Thomas A.; Garrard, Kenneth P.; Marston, Zachary

2016-07-12

Systems and methods for performing on-machine measurements and automatic part alignment, including: a measurement component operable for determining the position of a part on a machine; and an actuation component operable for adjusting the position of the part by contacting the part with a predetermined force responsive to the determined position of the part. The measurement component consists of a transducer. The actuation component consists of a linear actuator. Optionally, the measurement component and the actuation component consist of a single linear actuator operable for contacting the part with a first lighter force for determining the position of the part and with a second harder force for adjusting the position of the part. The actuation component is utilized in a substantially horizontal configuration and the effects of gravitational drop of the part are accounted for in the force applied and the timing of the contact.

Filtering fens: mechanisms explaining phosphorus-limited hotspots of biodiversity in wetlands adjacent to heavily fertilized areas.

PubMed

Cusell, Casper; Kooijman, Annemieke; Fernandez, Filippo; van Wirdum, Geert; Geurts, Jeroen J M; van Loon, E Emiel; Kalbitz, Karsten; Lamers, Leon P M

2014-05-15

The conservation of biodiverse wetland vegetation, including that of rich fens, has a high priority at a global scale. Although P-eutrophication may strongly decrease biodiversity in rich fens, some well-developed habitats do still survive in highly fertilized regions due to nutrient filtering services of large wetlands. The occurrence of such nutrient gradients is well-known, but the biogeochemical mechanisms that determine these patterns are often unclear. We therefore analyzed chemical speciation and binding of relevant nutrients and minerals in surface waters, soils and plants along such gradients in the large Ramsar nature reserve Weerribben-Wieden in the Netherlands. P-availability was lowest in relatively isolated floating rich fens, where plant N:P ratios indicated P-limitation. P-limitation can persist here despite high P-concentrations in surface waters near the peripheral entry locations, because only a small part of the P-input reaches the more isolated waters and fens. This pattern in P-availability appears to be primarily due to precipitation of Fe-phosphates, which mainly occurs close to entry locations as indicated by decreasing concentrations of Fe- and Al-bound P in the sub-aquatic sediments along this gradient. A further decrease of P-availability is caused by biological sequestration, which occurs throughout the wetland as indicated by equal concentrations of organic P in all sub-aquatic sediments. Our results clearly show that the periphery of large wetlands does indeed act as an efficient P-filter, sustaining the necessary P-limitation in more isolated parts. However, this filtering function does harm the ecological quality of the peripheral parts of the reserve. The filtering mechanisms, such as precipitation of Fe-phosphates and biological uptake of P, are crucial for the conservation and restoration of biodiverse rich fens in wetlands that receive eutrophic water from their surroundings. This seems to implicate that biodiverse wetland vegetation requires larger areas, as long as eutrophication has not been seriously tackled. Copyright © 2014 Elsevier B.V. All rights reserved.

How and when to terminate the Pleistocene ice ages?

NASA Astrophysics Data System (ADS)

Abe-Ouchi, A.; Saito, F.; Kawamura, K.; Takahashi, K.; Raymo, M. E.; Okuno, J.; Blatter, H.

2015-12-01

Climate change with wax and wane of large Northern Hemisphere ice sheet occurred in the past 800 thousand years characterized by 100 thousand year cycle with a large amplitude of sawtooth pattern, following a transition from a period of 40 thousand years cycle with small amplitude of ice sheet change at about 1 million years ago. Although the importance of insolation as the ultimate driver is now appreciated, the mechanism what determines timing and strength of terminations are far from clearly understood. Here we show, using comprehensive climate and ice-sheet models, that insolation and internal feedbacks between the climate, the ice sheets and the lithosphere-asthenosphere system explain the 100,000-year periodicity. The responses of equilibrium states of ice sheets to summer insolation show hysteresis, with the shape and position of the hysteresis loop playing a key part in determining the periodicities of glacial cycles. The hysteresis loop of the North American ice sheet is such that after inception of the ice sheet, its mass balance remains mostly positive through several precession cycles, whose amplitudes decrease towards an eccentricity minimum. The larger the ice sheet grows and extends towards lower latitudes, the smaller is the insolation required to make the mass balance negative. Therefore, once a large ice sheet is established, a moderate increase in insolation is sufficient to trigger a negative mass balance, leading to an almost complete retreat of the ice sheet within several thousand years. We discuss further the mechanism which determine the timing of ice age terminations by examining the role of astronomical forcing and change of atmospheric carbon dioxide contents through sensitivity experiments and comparison of several ice age cycles with different settings of astronomical forcings.

Ground-water flow in low permeability environments

USGS Publications Warehouse

Neuzil, Christopher E.

1986-01-01

Certain geologic media are known to have small permeability; subsurface environments composed of these media and lacking well developed secondary permeability have groundwater flow sytems with many distinctive characteristics. Moreover, groundwater flow in these environments appears to influence the evolution of certain hydrologic, geologic, and geochemical systems, may affect the accumulation of pertroleum and ores, and probably has a role in the structural evolution of parts of the crust. Such environments are also important in the context of waste disposal. This review attempts to synthesize the diverse contributions of various disciplines to the problem of flow in low-permeability environments. Problems hindering analysis are enumerated together with suggested approaches to overcoming them. A common thread running through the discussion is the significance of size- and time-scale limitations of the ability to directly observe flow behavior and make measurements of parameters. These limitations have resulted in rather distinct small- and large-scale approaches to the problem. The first part of the review considers experimental investigations of low-permeability flow, including in situ testing; these are generally conducted on temporal and spatial scales which are relatively small compared with those of interest. Results from this work have provided increasingly detailed information about many aspects of the flow but leave certain questions unanswered. Recent advances in laboratory and in situ testing techniques have permitted measurements of permeability and storage properties in progressively “tighter” media and investigation of transient flow under these conditions. However, very large hydraulic gradients are still required for the tests; an observational gap exists for typical in situ gradients. The applicability of Darcy's law in this range is therefore untested, although claims of observed non-Darcian behavior appear flawed. Two important nonhydraulic flow phenomena, osmosis and ultrafiltration, are experimentally well established in prepared clays but have been incompletely investigated, particularly in undisturbed geologic media. Small-scale experimental results form much of the basis for analyses of flow in low-permeability environments which occurs on scales of time and size too large to permit direct observation. Such large-scale flow behavior is the focus of the second part of the review. Extrapolation of small-scale experimental experience becomes an important and sometimes controversial problem in this context. In large flow systems under steady state conditions the regional permeability can sometimes be determined, but systems with transient flow are more difficult to analyze. The complexity of the problem is enhanced by the sensitivity of large-scale flow to the effects of slow geologic processes. One-dimensional studies have begun to elucidate how simple burial or exhumation can generate transient flow conditions by changing the state of stress and temperature and by burial metamorphism. Investigation of the more complex problem of the interaction of geologic processes and flow in two and three dimensions is just beginning. Because these transient flow analyses have largely been based on flow in experimental scale systems or in relatively permeable systems, deformation in response to effective stress changes is generally treated as linearly elastic; however, this treatment creates difficulties for the long periods of interest because viscoelastic deformation is probably significant. Also, large-scale flow simulations in argillaceous environments generally have neglected osmosis and ultrafiltration, in part because extrapolation of laboratory experience with coupled flow to large scales under in situ conditions is controversial. Nevertheless, the effects are potentially quite important because the coupled flow might cause ultra long lived transient conditions. The difficulties associated with analysis are matched by those of characterizing hydrologic conditions in tight environments; measurements of hydraulic head and sampling of pore fluids have been done only rarely because of the practical difficulties involved. These problems are also discussed in the second part of this paper.

Element concentrations in growth rings of trees near an abandoned wood-preserving plant site at Jackson, Tennessee

USGS Publications Warehouse

Yanosky, T.M.; Carmichael, J.K.

1993-01-01

Multielement analysis was performed on individual annual rings of trees growing at and near an abandoned wood-preserving plant site in Jackson, Tennessee, that operated from the early 1930's until 1981. Numerous organic compounds associated with the wood-preserving process have been detected in soils, ground water, and surface water within much of the site. Tree-ring investigations were conducted prior to investigations of ground water downgradient from the site to determine if trees preserved an areal and temporal record of contaminant movement into offsite areas. Increment cores were collected from trees on the abandoned plant site, in downgradient areas west and south of the site, and at two locations presumably unaffected by contamination from the site. Multielement analysis by proton-induced X-ray emission was performed on 5 to 15 individual growth rings from each of 34 trees that ranged in age from about 5 to 50 years. Concentrations of 16 elements were evaluated by analyzing average concentrations within the 1987, 1989, and 1990 rings of all trees; analyzing element-concentration trends along entire core radii; and analyzing element correlations between and among trees. Concentrations of some nutrients and trace metals were elevated in the outermost sapwood rings of some trees that grow south and southwest of the most contaminated part of the site; small trees on the main part of the site and larger trees to the west generally contained fewer rings with elevated concentrations, particularly of trace metals. Concentrations of several elements elevated in tree rings also were elevated in water samples collected from the reach of a stream that flows near the southwestern part of the site. Multielement analysis of each ring of a willow growing along the southern boundary of the site detected extremely large concentrations of chromium, nickel, and iron in rings that formed in 1986 and thereafter. Relative increases in the concentrations of these elements also were detected in a silver maple growing next to the willow, but not in another silver maple growing 150 meters farther to the west. An oak growing in the southwestern part of the study area contained large concentrations of calcium and several trace elements, and some trees south of the abandoned site contained large concentrations of phosphorus or potassium. Concentrations of trace metals and nutrients in some trees may be related to wood-preserving activities at the site and possibly to remedial efforts conducted during the early to mid 1980's.However, the possibility cannot be discounted that large concentrations of some elements are from sources other than the wood-preserving facility, or in part from flooding of the South Fork Forked Deer River.

The comparative anatomy of the pig middle ear cavity: a model for middle ear inflammation in the human?

PubMed Central

PRACY, J. P.; WHITE, A.; MUSTAFA, Y.; SMITH, D.; PERRY, M. E.

1998-01-01

This study was undertaken to develop a functional model of otitis media with effusion (OME) in the pig (Sus scrofa), with the purpose of investigating the origin of lymphocytes populating the middle ear during the course of an inflammatory process. The relevance of the model to the human condition of OME is to a large extent dependent on the anatomical and physiological similarities between the middle ear cavity and the pharyngeal lymphoid tissue of the pig and man. Anatomical specimens were collected from 7 young Large White pigs to determine the gross anatomy of the middle ear cavity and the histological characteristics of the middle ear mucosa. It was found that the anatomy of the 3 parts of the middle ear cavity in man and in the pig is broadly similar, although some minor differences were observed. The porcine eustachian tube was seen to be cartilaginous throughout its length in contrast to the part osseous, part cartilaginous structure found in man; the porcine ossicles were slightly different in shape to those of man and the air cell system was situated inferior to the tympanic cavity in the pig as opposed to posteriorly in man. This paper describes the structure and morphology of the pig middle ear cavity and compares and contrasts it with that of man. The minor differences observed are of anatomical importance but do not diminish the usefulness of the pig middle ear cleft as a potential model for human middle ear disorders. PMID:9688502

An international dosimetry exchange for boron neutron capture therapy. Part I: Absorbed dose measurements.

PubMed

Binns, P J; Riley, K J; Harling, O K; Kiger, W S; Munck af Rosenschöld, P M; Giusti, V; Capala, J; Sköld, K; Auterinen, I; Serén, T; Kotiluoto, P; Uusi-Simola, J; Marek, M; Viererbl, L; Spurny, F

2005-12-01

An international collaboration was organized to undertake a dosimetry exchange to enable the future combination of clinical data from different centers conducting neutron capture therapy trials. As a first step (Part I) the dosimetry group from the Americas, represented by MIT, visited the clinical centers at Studsvik (Sweden), VTT Espoo (Finland), and the Nuclear Research Institute (NRI) at Rez (Czech Republic). A combined VTT/NRI group reciprocated with a visit to MIT. Each participant performed a series of dosimetry measurements under equivalent irradiation conditions using methods appropriate to their clinical protocols. This entailed in-air measurements and dose versus depth measurements in a large water phantom. Thermal neutron flux as well as fast neutron and photon absorbed dose rates were measured. Satisfactory agreement in determining absorbed dose within the experimental uncertainties was obtained between the different groups although the measurement uncertainties are large, ranging between 3% and 30% depending upon the dose component and the depth of measurement. To improve the precision in the specification of absorbed dose amongst the participants, the individually measured dose components were normalized to the results from a single method. Assuming a boron concentration of 15 microg g(-1) that is typical of concentrations realized clinically with the boron delivery compound boronophenylalanine-fructose, systematic discrepancies in the specification of the total biologically weighted dose of up to 10% were apparent between the different groups. The results from these measurements will be used in future to normalize treatment plan calculations between the different clinical dosimetry protocols as Part II of this study.

3D modelling of the flow of self-compacting concrete with or without steel fibres. Part II: L-box test and the assessment of fibre reorientation during the flow

NASA Astrophysics Data System (ADS)

Deeb, R.; Kulasegaram, S.; Karihaloo, B. L.

2014-12-01

The three-dimensional Lagrangian particle-based smooth particle hydrodynamics method described in Part I of this two-part paper is used to simulate the flow of self-compacting concrete (SCC) with and without steel fibres in the L-box configuration. As in Part I, the simulation of the SCC mixes without fibres emphasises the distribution of large aggregate particles of different sizes throughout the flow, whereas the simulation of high strength SCC mixes which contain steel fibres is focused on the distribution of fibres and their orientation during the flow. The capabilities of this methodology are validated by comparing the simulation results with the L-box test carried out in the laboratory. A simple method is developed to assess the reorientation and distribution of short steel fibres in self-compacting concrete mixes during the flow. The reorientation of the fibres during the flow is used to estimate the fibre orientation factor (FOF) in a cross section perpendicular to the principal direction of flow. This estimation procedure involves the number of fibres cut by the section and their inclination to the cutting plane. This is useful to determine the FOF in practical image analysis on cut sections.

Engineering and characterization of fluorogenic glycine riboswitches.

PubMed

Ketterer, Simon; Gladis, Lukas; Kozica, Adnan; Meier, Matthias

2016-07-08

A set of 12 fluorogenic glycine riboswitches with different thermodynamic and kinetic response properties was engineered. For the design of functional riboswitches, a three-part RNA approach was applied based on the idea of linking a RNA sensor, transmitter and actuator part together. For the RNA sensor and actuator part, we used the tandem glycine aptamer structure from Bacillus subtillis, and fluorogenic aptamer Spinach, respectively. To achieve optimal signal transduction from the sensor to the actuator, a riboswitch library with variable transmitter was screened with a microfluidic large-scale integration chip. This allowed us to establish the complete thermodynamic binding profiles of the riboswitch library. Glycine dissociation constants of the 12 strong fluorescence response riboswitches varied between 99.7 and 570 μM. Furthermore, the kinetic glycine binding (k(on)), and dissociation (k(off)) rates, and corresponding energy barriers of the 10 strongest fluorescence response riboswitches were determined with the same chip platform. k(on) and k(off) were in the order of 10(-3)s(-1) and 10(-2)s(-1), respectively. Conclusively, we demonstrate that systematic screening of synthetic and natural linked RNA parts with microfluidic chip technology is an effective approach to rapidly generate fluorogenic metabolite riboswitches with a broad range of biophysical response properties. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Method for compression of data using single pass LZSS and run-length encoding

DOEpatents

Berlin, G.J.

1997-12-23

A method used preferably with LZSS-based compression methods for compressing a stream of digital data is disclosed. The method uses a run-length encoding scheme especially suited for data strings of identical data bytes having large run-lengths, such as data representing scanned images. The method reads an input data stream to determine the length of the data strings. Longer data strings are then encoded in one of two ways depending on the length of the string. For data strings having run-lengths less than 18 bytes, a cleared offset and the actual run-length are written to an output buffer and then a run byte is written to the output buffer. For data strings of 18 bytes or longer, a set offset and an encoded run-length are written to the output buffer and then a run byte is written to the output buffer. The encoded run-length is written in two parts obtained by dividing the run length by a factor of 255. The first of two parts of the encoded run-length is the quotient; the second part is the remainder. Data bytes that are not part of data strings of sufficient length are written directly to the output buffer. 3 figs.

Hydrogeology of the Sulphur Springs area, Tampa, Florida

USGS Publications Warehouse

Stewart, J.W.; Mills, L.R.

1984-01-01

The Sulfur Springs area includes about 56 square miles in west-central Hillsborough County, Florida. The north-central part of the city of Tampa is highly urbanized; the north-west part of the area is rural or undeveloped. The area has numerous sinkholes, two of which are used as retention basins for urban storm runoff. An intermittent stream discharges into a sinkhole that is hydraulically connected with the Floridian aquifer. A well-developed cavity system occurs in the upper part of the aquifer in the southwestern and southeastern parts of the area. Groundwater velocities of 4,200 to 9,200 feet per day were determined from dye tests conducted in a sinkhole area north of Sulfur Springs. Sulfur Springs provides the city of Tampa a supplemental water supply of 20 million gallons per day. Periodically, the spring pool is closed to swimming because of the high bacteria counts in the water. The source of bacteria appears to be an internally drained sinkhole area north of the spring. In 1980, groundwater use in the study area, excluding withdrawals from Sulphur Springs, was 7.2 million gallons per day, largely for public water supplies. The city of Tampa pumped an average of 48.5 million gallons per day from the Tampa Dam Reservoir on the Hillsborough River. (USGS)

Computational study of culture conditions and nutrient supply in a hollow membrane sheet bioreactor for large-scale bone tissue engineering.

PubMed

Khademi, Ramin; Mohebbi-Kalhori, Davod; Hadjizadeh, Afra

2014-03-01

Successful bone tissue culture in a large implant is still a challenge. We have previously developed a porous hollow membrane sheet (HMSh) for tissue engineering applications (Afra Hadjizadeh and Davod Mohebbi-Kalhori, J Biomed. Mater. Res. Part A [2]). This study aims to investigate culture conditions and nutrient supply in a bioreactor made of HMSh. For this purpose, hydrodynamic and mass transport behavior in the newly proposed hollow membrane sheet bioreactor including a lumen region and porous membrane (scaffold) for supporting and feeding cells with a grooved section for accommodating gel-cell matrix was numerically studied. A finite element method was used for solving the governing equations in both homogenous and porous media. Furthermore, the cell resistance and waste production have been included in a 3D mathematical model. The influences of different bioreactor design parameters and the scaffold properties which determine the HMSh bioreactor performance and various operating conditions were discussed in detail. The obtained results illustrated that the novel scaffold can be employed in the large-scale applications in bone tissue engineering.

A new mechanistic approach for the further development of a population with established size bimodality

USGS Publications Warehouse

Heerman, Lisa; DeAngelis, Donald L.; Borcherding, Jost

2017-01-01

Usually, the origin of a within-cohort bimodal size distribution is assumed to be caused by initial size differences or by one discrete period of accelerated growth for one part of the population. The aim of this study was to determine if more continuous pathways exist allowing shifts from the small to the large fraction within a bimodal age-cohort. Therefore, a Eurasian perch population, which had already developed a bimodal size-distribution and had differential resource use of the two size-cohorts, was examined. Results revealed that formation of a bimodal size-distribution can be a continuous process. Perch from the small size-cohort were able to grow into the large size-cohort by feeding on macroinvertebrates not used by their conspecifics. The diet shifts were accompanied by morphological shape changes. Intra-specific competition seemed to trigger the development towards an increasing number of large individuals. A stage-structured matrix model confirmed these assumptions. The fact that bimodality can be a continuous process is important to consider for the understanding of ecological processes and links within ecosystems.

A new mechanistic approach for the further development of a population with established size bimodality

PubMed Central

DeAngelis, Donald L.; Borcherding, Jost

2017-01-01

Usually, the origin of a within-cohort bimodal size distribution is assumed to be caused by initial size differences or by one discrete period of accelerated growth for one part of the population. The aim of this study was to determine if more continuous pathways exist allowing shifts from the small to the large fraction within a bimodal age-cohort. Therefore, a Eurasian perch population, which had already developed a bimodal size-distribution and had differential resource use of the two size-cohorts, was examined. Results revealed that formation of a bimodal size-distribution can be a continuous process. Perch from the small size-cohort were able to grow into the large size-cohort by feeding on macroinvertebrates not used by their conspecifics. The diet shifts were accompanied by morphological shape changes. Intra-specific competition seemed to trigger the development towards an increasing number of large individuals. A stage-structured matrix model confirmed these assumptions. The fact that bimodality can be a continuous process is important to consider for the understanding of ecological processes and links within ecosystems. PMID:28650963

Contact Modelling of Large Radius Air Bending with Geometrically Exact Contact Algorithm

NASA Astrophysics Data System (ADS)

Vorkov, V.; Konyukhov, A.; Vandepitte, D.; Duflou, J. R.

2016-08-01

Usage of high-strength steels in conventional air bending is restricted due to limited bendability of these metals. Large-radius punches provide a typical approach for decreasing deformations during the bending process. However, as deflection progresses the loading scheme changes gradually. Therefore, modelling of the contact interaction is essential for an accurate description of the loading scheme. In the current contribution, the authors implemented a plane frictional contact element based on the penalty method. The geometrically exact contact algorithm is used for the penetration determination. The implementation is done using the OOFEM - open source finite element solver. In order to verify the simulation results, experiments have been conducted on a bending press brake for 4 mm Weldox 1300 with a punch radius of 30 mm and a die opening of 80 mm. The maximum error for the springback calculation is 0.87° for the bending angle of 144°. The contact interaction is a crucial part of large radius bending simulation and the implementation leads to a reliable solution for the springback angle.

40 CFR Appendix D to Part 112 - Determination of a Worst Case Discharge Planning Volume

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 23 2013-07-01 2013-07-01 false Determination of a Worst Case Discharge Planning Volume D Appendix D to Part 112 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS OIL POLLUTION PREVENTION Pt. 112, App. D Appendix D to Part 112—Determination of a...

40 CFR Appendix D to Part 112 - Determination of a Worst Case Discharge Planning Volume

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Determination of a Worst Case Discharge Planning Volume D Appendix D to Part 112 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS OIL POLLUTION PREVENTION Pt. 112, App. D Appendix D to Part 112—Determination of a...

40 CFR Appendix D to Part 112 - Determination of a Worst Case Discharge Planning Volume

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 22 2014-07-01 2013-07-01 true Determination of a Worst Case Discharge Planning Volume D Appendix D to Part 112 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS OIL POLLUTION PREVENTION Pt. 112, App. D Appendix D to Part 112—Determination of a...

40 CFR Appendix D to Part 112 - Determination of a Worst Case Discharge Planning Volume

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 22 2011-07-01 2011-07-01 false Determination of a Worst Case Discharge Planning Volume D Appendix D to Part 112 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS OIL POLLUTION PREVENTION Pt. 112, App. D Appendix D to Part 112—Determination of a...

40 CFR Appendix D to Part 112 - Determination of a Worst Case Discharge Planning Volume

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 23 2012-07-01 2012-07-01 false Determination of a Worst Case Discharge Planning Volume D Appendix D to Part 112 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER PROGRAMS OIL POLLUTION PREVENTION Pt. 112, App. D Appendix D to Part 112—Determination of a...

45 CFR 1155.500 - How are violations of this part determined for recipients other than individuals?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false How are violations of this part determined for recipients other than individuals? 1155.500 Section 1155.500 Public Welfare Regulations Relating to Public... Consequences § 1155.500 How are violations of this part determined for recipients other than individuals? A...

45 CFR 1155.505 - How are violations of this part determined for recipients who are individuals?

Code of Federal Regulations, 2010 CFR

2010-10-01

... 45 Public Welfare 3 2010-10-01 2010-10-01 false How are violations of this part determined for recipients who are individuals? 1155.505 Section 1155.505 Public Welfare Regulations Relating to Public... Consequences § 1155.505 How are violations of this part determined for recipients who are individuals? An...

Laser Heating in a Dense Plasma Focus.

DTIC Science & Technology

The report is divided in two parts. In the first part an account is given of the measurement of the momentum distribution of the deuterons ejected from a dense plasma focus . The results show the existence of a pronounced non-Maxwellian distribution and a small population of deuterons accelerated to the voltage of the condenser bank. In the second part theoretical calculation of laser heating establish the presence of large density gradient which probably accounts for the large currents detected in such plasmas. (Author)

Landscape Suitability in Botswana for the Conservation of Its Six Large African Carnivores

PubMed Central

Winterbach, Hanlie E. K.; Winterbach, Christiaan W.; Somers, Michael J.

2014-01-01

Wide-ranging large carnivores often range beyond the boundaries of protected areas into human-dominated areas. Mapping out potentially suitable habitats on a country-wide scale and identifying areas with potentially high levels of threats to large carnivore survival is necessary to develop national conservation action plans. We used a novel approach to map and identify these areas in Botswana for its large carnivore guild consisting of lion (Panthera leo), leopard (Panthera pardus), spotted hyaena (Crocuta crocuta), brown hyaena (Hyaena brunnea), cheetah (Acinonyx jubatus) and African wild dog (Lycaon pictus). The habitat suitability for large carnivores depends primarily on prey availability, interspecific competition, and conflict with humans. Prey availability is most likely the strongest natural determinant. We used the distribution of biomass of typical wild ungulate species occurring in Botswana which is preyed upon by the six large carnivores to evaluate the potential suitability of the different management zones in the country to sustain large carnivore populations. In areas where a high biomass of large prey species occurred, we assumed interspecific competition between dominant and subordinated competitors to be high. This reduced the suitability of these areas for conservation of subordinate competitors, and vice versa. We used the percentage of prey biomass of the total prey and livestock biomass to identify areas with potentially high levels of conflict in agricultural areas. High to medium biomass of large prey was mostly confined to conservation zones, while small prey biomass was more evenly spread across large parts of the country. This necessitates different conservation strategies for carnivores with a preference for large prey, and those that can persist in the agricultural areas. To ensure connectivity between populations inside Botswana and also with its neighbours, a number of critical areas for priority management actions exist in the agricultural zones. PMID:24949735

Landscape suitability in Botswana for the conservation of its six large African carnivores.

PubMed

Winterbach, Hanlie E K; Winterbach, Christiaan W; Somers, Michael J

2014-01-01

Wide-ranging large carnivores often range beyond the boundaries of protected areas into human-dominated areas. Mapping out potentially suitable habitats on a country-wide scale and identifying areas with potentially high levels of threats to large carnivore survival is necessary to develop national conservation action plans. We used a novel approach to map and identify these areas in Botswana for its large carnivore guild consisting of lion (Panthera leo), leopard (Panthera pardus), spotted hyaena (Crocuta crocuta), brown hyaena (Hyaena brunnea), cheetah (Acinonyx jubatus) and African wild dog (Lycaon pictus). The habitat suitability for large carnivores depends primarily on prey availability, interspecific competition, and conflict with humans. Prey availability is most likely the strongest natural determinant. We used the distribution of biomass of typical wild ungulate species occurring in Botswana which is preyed upon by the six large carnivores to evaluate the potential suitability of the different management zones in the country to sustain large carnivore populations. In areas where a high biomass of large prey species occurred, we assumed interspecific competition between dominant and subordinated competitors to be high. This reduced the suitability of these areas for conservation of subordinate competitors, and vice versa. We used the percentage of prey biomass of the total prey and livestock biomass to identify areas with potentially high levels of conflict in agricultural areas. High to medium biomass of large prey was mostly confined to conservation zones, while small prey biomass was more evenly spread across large parts of the country. This necessitates different conservation strategies for carnivores with a preference for large prey, and those that can persist in the agricultural areas. To ensure connectivity between populations inside Botswana and also with its neighbours, a number of critical areas for priority management actions exist in the agricultural zones.

Measurements of the $W$ Boson Mass with the D0 Detector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lopes de Sa, Rafael

2013-01-01

In the first part, we describe what is the W boson mass in the context of the Standard Model. We discuss the prominent role this physical observable plays in the determination of the internal self consistency of the Electroweak Sector. We review measurements and calculation of the W boson mass done in past and argue about the importance and feasibility of improving the experimental determination. We give a description of the Fermilab Tevatron Collider and the D0 detector, highlighting the relevant parts for the measurement described in this Dissertation. In the second part, we give a detailed description of amore » measurement of the W boson mass using the D0 Central Calorimeter. The measurement uses 1.68 x 10 6 candidates from W → en decays, corresponding to 4.3 fb -1 of integrated luminosity collected from 2006 to 2009. We measure the mass using the transverse mass, electron transverse momentum, and missing transverse energy distributions. The transverse mass and electron transverse momentum measurements are the most precise and are combined to give MW = 80.367 ± 0.013(stat) ± 0.023 (syst) GeV = 80.367 ± 0.026 GeV. This is combined with an earlier D0 result determined using an independent 1 fb -1 data sample, also with central electrons only, to give M W = 80.375± 0.023 GeV. The uncertainty in the measurement is dominated by the determination of the calorimeter electron energy scale, the W sample size, the knowledge of the parton distribution function. In the third part, we discuss methods of reducing the dominant uncertainties in the W boson mass measurements. We show that introducing electrons detected in the End Calorimeters greatly reduce the measurement systematic uncertainty, especially the on related to the parton distribution functions. We describe a precise calibration of the End Calorimeter using Z → ee events corresponding to 4.3 fb -1 of integrated luminosity. The calibration is an important milestone in a measurement that explores a larger part of the D0 Calorimeter. We present parametrized models that describe the response of the End Calorimeters to electron showers and soft hadronic particles, giving special attention to the specific challenges of a measurement in the forward region: the inhomogeneity of the uninstrumented materials, the large hadronic energy flow in the calorimeter and the jet misidentification probability.« less

Sedimentary records of trace elements from large European lakes (Switzerland) document historic to recent freshwater pollution and climate-induced runoff variations

NASA Astrophysics Data System (ADS)

Thevenon, F.; Wirth, S. B.; Fujak, M.; Poté, J.; Thierry, A.; Chiaradia, M.; Girardclos, S.

2011-12-01

Continuous sedimentary records of anthropogenic and natural trace elements determined by ICPMS, from 5 large and deep perialpine lakes from Central Europe (Switzerland), evidence the environmental impacts of industrial fossil fuel pollution. In fact, the greatest increase in heavy metal pollution was registered at all the studied sites following the European industrial revolution of ca. AD 1800; with the highest values during the middle part of the 20th century. On a regional scale, anthropogenic heavy metal input subsequently stopped increasing thanks to remediation strategies such as the implementation of wastewater treatment plants (WWTPs). On the other hand, the discharge of industrial treated wastewaters into Vidy Bay of Lake Geneva during the second part of the 20th century involved the sedimentation of highly contaminated sediments in the area surrounding the WWTP outlet pipe discharge; less than 4 km from the main supply of drinking water of Lausanne (127'000 hab.). Microbial analyses furthermore reveal i) high increase in bacterial densities following the lake eutrophication in the 1970s, and that ii) the related sediments can be considered as a reservoir of antibiotic resistant bacteria/genes (of human origin). We finally compare instrumental hydrological data over the last century with variations of lithogenic trace elements (e.g., titanium) as registered in three large lakes (Brienz, Thun and Bienne) connected by the River Aar. This task allows to better constraining the runoff variations on a regional scale over the last decades for the the River Aar, and its possible increase under warming climate conditions in the European Alps.

Slip distribution of the 1952 Tokachi-Oki earthquake (M 8.1) along the Kuril Trench deduced from tsunami waveform inversion

USGS Publications Warehouse

Hirata, K.; Geist, E.; Satake, K.; Tanioka, Y.; Yamaki, S.

2003-01-01

We inverted 13 tsunami waveforms recorded in Japan to estimate the slip distribution of the 1952 Tokachi-Oki earthquake (M 8.1), which occurred southeast off Hokkaido along the southern Kuril subduction zone. The previously estimated source area determined from tsunami travel times [Hatori, 1973] did not coincide with the observed aftershock distribution. Our results show that a large amount of slip occurred in the aftershock area east of Hatori's tsunami source area, suggesting that a portion of the interplate thrust near the trench was ruptured by the main shock. We also found more than 5 m of slip along the deeper part of the seismogenic interface, just below the central part of Hatori's tsunami source area. This region, which also has the largest stress drop during the main shock, had few aftershocks. Large tsunami heights on the eastern Hokkaido coast are better explained by the heterogeneous slip model than previous uniform-slip fault models. The total seismic moment is estimated to be 1.87 ?? 1021 N m, giving a moment magnitude of Mw = 8.1. The revised tsunami source area is estimated to be 25.2 ?? 103 km2, ???3 times larger than the previous tsunami source area. Out of four large earthquakes with M ??? 7 that subsequently occurred in and around the rupture area of the 1952 event, three were at the edges of regions with relatively small amount of slip. We also found that a subducted seamount near the edge of the rupture area possibly impeded slip along the plate interface.

Conservation of chromosomes syntenic with avian autosomes in squamate reptiles revealed by comparative chromosome painting.

PubMed

Pokorná, Martina; Giovannotti, Massimo; Kratochvíl, Lukáš; Caputo, Vincenzo; Olmo, Ettore; Ferguson-Smith, Malcolm A; Rens, Willem

2012-08-01

In contrast to mammals, birds exhibit a slow rate of chromosomal evolution. It is not clear whether high chromosome conservation is an evolutionary novelty of birds or was inherited from an earlier avian ancestor. The evolutionary conservatism of macrochromosomes between birds and turtles supports the latter possibility; however, the rate of chromosomal evolution is largely unknown in other sauropsids. In squamates, we previously reported strong conservatism of the chromosomes syntenic with the avian Z, which could reflect a peculiarity of this part of the genome. The chromosome 1 of iguanians and snakes is largely syntenic with chromosomes 3, 5 and 7 of the avian ancestral karyotype. In this project, we used comparative chromosome painting to determine how widely this synteny is conserved across nine families covering most of the main lineages of Squamata. The results suggest that the association of the avian ancestral chromosomes 3, 5 and 7 can be dated back to at least the early Jurassic and could be an ancestral characteristic for Unidentata (Serpentes, Iguania, Anguimorpha, Laterata and Scinciformata). In Squamata chromosome conservatism therefore also holds for the parts of the genome which are homologous to bird autosomes, and following on from this, a slow rate of chromosomal evolution could be a common characteristic of all sauropsids. The large evolutionary stasis in chromosome organization in birds therefore seems to be inherited from their ancestors, and it is particularly striking in comparison with mammals, probably the only major tetrapod lineage with an increased rate of chromosomal rearrangements as a whole.

Safety and Abuse Testing of Energizer LiFeS2 AA Cells

NASA Technical Reports Server (NTRS)

Jeevarajan, Judith A.; Baldwin, Laura; Bragg, Bobby J.

2003-01-01

The LiFeS2 test program was part of the study on state-of-the-art batteries/cells available in the commercial market. It was carried out in an effort to replace alkaline AA cells for Shuttle and Station applications. A large number of alkaline cells are used for numerous Shuttle and Station applications as loose cells. Other government agencies reported good performance and abuse tolerance of the AA LiFeS2 cells. In this study, only abuse testing was performed on the cells to determine their tolerance. The tests carried out were over-discharge, external short circuit, heat-to-vent, vibration and drop.

Managing Quality and Safety in Real Time? Evidence from an Interview Study.

PubMed

Randell, Rebecca; Keen, Justin; Gates, Cara; Ferguson, Emma; Long, Andrew; Ginn, Claire; McGinnis, Elizabeth; Whittle, Jackie

2016-01-01

Health systems around the world are investing increasing effort in monitoring care quality and safety. Dashboards can support this process, providing summary data on processes and outcomes of care, making use of data visualization techniques such as graphs. As part of a study exploring development and use of dashboards in English hospitals, we interviewed senior managers across 15 healthcare providers. Findings revealed substantial variation in sophistication of the dashboards in place, largely presenting retrospective data items determined by national bodies and dependent on manual collation from a number of systems. Where real time systems were in place, they supported staff in proactively managing quality and safety.

Windrow composting as an effective method to dispose of large numbers of fish

USGS Publications Warehouse

Tabb, L.C.I.; Starliper, C.E.; Shotts, E.B.; Everson, J.; Palmisano, A.W.

1998-01-01

During July 1998, at the USGS Leetown Science Center, Kearneysville, West Virginia, an epizootic occurred in 16-month-old Atlantic salmon (Salmo salar). The cause ofmortality was diagnosed as furunculosis, a serious disease in salmonid fishes caused by the bacterium Aeromonas salmonicida. The fish were being maintained as part ofongoing research and were held in uncovered 30-m-Iong concrete raceways, each supplied with about 757 L per minute of 12 ?C pathogen-free spring water. The means by which the fish became infected could not be determined, and there was no recent history offurunculosis in the hatchery system.

Small-angle neutron scattering study of recombinant yeast-derived human hepatitis B virus surface antigen vaccine particle

NASA Astrophysics Data System (ADS)

Sato, M.; Ito, Y.; Kameyama, K.; Imai, M.; Ishikawa, N.; Takagi, T.

1995-02-01

The overall and internal structure of recombinant yeast-derived human hepatitis B virus surface antigen vaccine particles was investigated by small-angle neutron scattering using the contrast variation method. The vaccine is a nearly spherical particle, and its contrast-matching point was determined to be at about 24% D 2O content, indicating that a large part of the vaccine particle is occupied by lipids and carbohydrates from the yeast. The Stuhrmann plot suggests that the surface antigens exist predominantly in the peripheral region of the particle, which is favorable to the induction of anti-virus antibodies.

On the accuracy of various large axial displacement formulae for crooked columns

NASA Astrophysics Data System (ADS)

Mallis, J.; Kounadis, A. N.

1988-11-01

The axial displacements of an initially crooked, simply supported column, subjected to an axial compressive force at its end, are determined by using several variants of the axial strain-displacement relationship. Their accuracy and range of applicability are thoroughly discussed by comparing the corresponding results with those of the exact elastica analysis in which the compressibility effect of the bar axis is accounted for. Among other findings, the important conclusion is drawn that the simplified linear kinematic relation leads to a sufficiently accurate evaluation of the initial part of the postbuckling path which is of significant importance for structural design purposes.

Statistical issues in the design and planning of proteomic profiling experiments.

PubMed

Cairns, David A

2015-01-01

The statistical design of a clinical proteomics experiment is a critical part of well-undertaken investigation. Standard concepts from experimental design such as randomization, replication and blocking should be applied in all experiments, and this is possible when the experimental conditions are well understood by the investigator. The large number of proteins simultaneously considered in proteomic discovery experiments means that determining the number of required replicates to perform a powerful experiment is more complicated than in simple experiments. However, by using information about the nature of an experiment and making simple assumptions this is achievable for a variety of experiments useful for biomarker discovery and initial validation.

Luminosity limits for liquid argon calorimetry

NASA Astrophysics Data System (ADS)

J, Rutherfoord; B, Walker R.

2012-12-01

We have irradiated liquid argon ionization chambers with betas using high-activity Strontium-90 sources. The radiation environment is comparable to that in the liquid argon calorimeters which are part of the ATLAS detector installed at CERN's Large Hadron Collider. We measure the ionization current over a wide range of applied potential for two different source activities and for three different chamber gaps. These studies provide operating experience at exceptionally high ionization rates. We can operate these chambers either in the normal mode or in the space-charge limited regime and thereby determine the transition point between the two. From the transition point we indirectly extract the positive argon ion mobility.

Quinoxaline derivatives: a patent review (2006--present).

PubMed

González, Mercedes; Cerecetto, Hugo

2012-11-01

Quinoxaline scaffold is included in a large number of therapeutic agents because of its physicochemical properties that make the difference between them and the carbono analogue, naphthalene. This review of patented products presents the quinoxaline heterocycle as part of the structural patent claims from a medicinal chemistry perspective. We centred our discussion in the various drug patent applications of the quinoxaline and its derivatives. The applications are based firstly in the specific enzyme target with very low development in the disease treatment. Only for cancer and antimicrobial agents they were specifically determined but little is mentioned in order to insight in the last development activities.

BPMN, Toolsets, and Methodology: A Case Study of Business Process Management in Higher Education

NASA Astrophysics Data System (ADS)

Barn, Balbir S.; Oussena, Samia

This chapter describes ongoing action research which is exploring the use of BPMN and a specific toolset - Intalio Designer to capture the “as is” essential process model of part of an overarching large business process within higher education. The chapter contends that understanding the efficacy of the BPMN notation and the notational elements to use is not enough. Instead, the effectiveness of a notation is determined by the notation, the toolset that is being used, and methodological consideration. The chapter presents some of the challenges that are faced in attempting to develop computation independent models in BPMN using toolsets such as Intalio Designer™.

VizieR Online Data Catalog: OGLE eclipsing binaries in LMC (Wyrzykowski+, 2003)

NASA Astrophysics Data System (ADS)

Wyrzykowski, L.; Udalski, A.; Kubiak, M.; Szymanski, M.; Zebrun, K.; Soszynski, I.; Wozniak, P. R.; Pietrzynski, G.; Szewczyk, O.

2003-09-01

We present the catalog of 2580 eclipsing binary stars detected in 4.6 square degree area of the central parts of the Large Magellanic Cloud. The photometric data were collected during the second phase of the OGLE microlensing search from 1997 to 2000. The eclipsing objects were selected with the automatic search algorithm based on an artificial neural network. Basic statistics of eclipsing stars are presented. Also, the list of 36 candidates of detached eclipsing binaries for spectroscopic study and for precise LMC distance determination is provided. The full catalog is accessible from the OGLE Internet archive. (2 data files).

Part-crystalline part-liquid state and electrical/thermal transport in materials with chemical-bond hierarchy

NASA Astrophysics Data System (ADS)

Zhang, Wenqng

2015-03-01

A concept of part-crystalline part-liquid state (or liquid-like), and even part-crystalline part-glass state (or glass-like), was demonstrated in some materials such as Cu3SbSe3 with chemical-bond-hierarchy, in which certain constituent species weakly bond to other part of the crystal. Such a material could intrinsically manifest the coexistence of rigid crystalline sublattices and other fluctuating noncrystalline sublattices with thermally induced large amplitude vibrations and even flow of the group of species atoms. The large-amplitude vibrations and movement of atoms can generate unusual severe phonon scattering and thermal damping due to the collective low-frequency vibrations similar to the Boson peak in amorphous or liquid materials. While different phase or state may have large energetic discrepancy, whether the thermally-induced part-crystalline state is undergoing phase transition becomes an interesting issue. In addition, our earlier work reported that second-order phase transition could induce extreme electron and phonon scattering in thermoelectrics. The above work clearly demonstrated that the unusual effect from structural fluctuations on thermal and electrical transport in thermoelectrics should be paid attention to. While materials with these structural changes can retain extremely low lattice thermal conductivity and unusual electron transport and become promising candidates for high-performance thermoelectrics, underlying mechanism is yet to be explored.

Indentured Parts List Maintenance and Part Assembly Capture Tool - IMPACT

NASA Technical Reports Server (NTRS)

Jain, Bobby; Morris, Jill; Sharpe, Kelly

2004-01-01

Johnson Space Center's (JSC's) indentured parts list (IPL) maintenance and parts assembly capture tool (IMPACT) is an easy-to-use graphical interface for viewing and maintaining the complex assembly hierarchies of large databases. IMPACT, already in use at JSC to support the International Space Station (ISS), queries, updates, modifies, and views data in IPL and associated resource data, functions that it can also perform, with modification, for any large commercial database. By enabling its users to efficiently view and manipulate IPL hierarchical data, IMPACT performs a function unlike that of any other tool. Through IMPACT, users will achieve results quickly, efficiently, and cost effectively.

USSR Report, Chemistry

DTIC Science & Technology

1985-08-19

No 2, Mar-Apr 85) 15 Factors Which Determine Activity of Catalysts of Various Chemical Types in Hydrogen Oxidation Reactions . Part 1: Oxidation ...Factors Which Determine Activity of Catalysts of Various Chemical Types in Hydrogen Oxidation Reactions . Part 2: Oxidation and Isotope Exchange of...FACTORS WHICH DETERMINE ACTIVITY OF CATALYSTS OF VARIOUS CHEMICAL TYPES IN HYDROGEN OXIDATION REACTIONS . PART 1: OXIDATION AND ISOTOPE EXCHANGE OF

23 CFR Appendix D to Part 1240 - Determination of National Average Seat Belt Use Rate

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Determination of National Average Seat Belt Use Rate D Appendix D to Part 1240 Highways NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION AND FEDERAL HIGHWAY... BASED ON SEAT BELT USE RATES Pt. 1240, App. D Appendix D to Part 1240—Determination of National Average...

40 CFR Appendix C to Part 425 - Definition and Procedure for the Determination of the Method Detection Limit 1

Code of Federal Regulations, 2010 CFR

2010-07-01

... Determination of the Method Detection Limit 1 C Appendix C to Part 425 Protection of Environment ENVIRONMENTAL... CATEGORY Pt. 425, App. C Appendix C to Part 425—Definition and Procedure for the Determination of the... reagent water. (c) The concentration value that corresponds to the region of the standard curve where...

Indirect methods for reference interval determination - review and recommendations.

PubMed

Jones, Graham R D; Haeckel, Rainer; Loh, Tze Ping; Sikaris, Ken; Streichert, Thomas; Katayev, Alex; Barth, Julian H; Ozarda, Yesim

2018-04-19

Reference intervals are a vital part of the information supplied by clinical laboratories to support interpretation of numerical pathology results such as are produced in clinical chemistry and hematology laboratories. The traditional method for establishing reference intervals, known as the direct approach, is based on collecting samples from members of a preselected reference population, making the measurements and then determining the intervals. An alternative approach is to perform analysis of results generated as part of routine pathology testing and using appropriate statistical techniques to determine reference intervals. This is known as the indirect approach. This paper from a working group of the International Federation of Clinical Chemistry (IFCC) Committee on Reference Intervals and Decision Limits (C-RIDL) aims to summarize current thinking on indirect approaches to reference intervals. The indirect approach has some major potential advantages compared with direct methods. The processes are faster, cheaper and do not involve patient inconvenience, discomfort or the risks associated with generating new patient health information. Indirect methods also use the same preanalytical and analytical techniques used for patient management and can provide very large numbers for assessment. Limitations to the indirect methods include possible effects of diseased subpopulations on the derived interval. The IFCC C-RIDL aims to encourage the use of indirect methods to establish and verify reference intervals, to promote publication of such intervals with clear explanation of the process used and also to support the development of improved statistical techniques for these studies.

Lack of integration of automated external defibrillators with EMS response may reduce lifesaving potential of public-access defibrillation.

PubMed

Myers, J Brent; French, David; Webb, William

2005-01-01

Automated external defibrillators (AEDs) used for public-access defibrillation (PAD) allow for rapid defibrillation, particularly if the AEDs are incorporated into an organized response plan. This project was undertaken to determine how many PAD AEDs were in North Carolina, how many were properly registered, and how many were integrated into the emergency medical services (EMS) response. Data were collected for this prospective, descriptive study via phone survey, e-mail survey, and/or direct personal interview. Four sources were utilized: 1) state office of EMS AED registration database, 2) AED sales representatives, 3) county EMS agency representatives, and 4) American Heart Association (AHA) training center instructors and regional faculty. The primary endpoint was determining the proportion of AEDs placed in unregistered locations. The state EMS office provided the state registry of AED locations. One-hundred percent of state-recognized AED vendors and county EMS agencies provided data. Twelve of 55 (22%) AHA personnel provided data. Eight hundred eighty-one unique locations were identified. Although AED sales are required by law to be registered, the office of EMS database contained only 99 of the 552 (18%) unique PAD locations identified by the study. A large number of unregistered AEDs are being placed in communities. AEDs placed as part of an organized PAD program improve the rates of survival from sudden cardiac death. In the absence of registration, it is difficult to determine the extent to which these AEDs are part of an organized PAD program.

A transport model for computer simulation of wildfires

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linn, R.

1997-12-31

Realistic self-determining simulation of wildfires is a difficult task because of a large variety of important length scales (including scales on the size of twigs or grass and the size of large trees), imperfect data, complex fluid mechanics and heat transfer, and very complicated chemical reactions. The author uses a transport approach to produce a model that exhibits a self-determining propagation rate. The transport approach allows him to represent a large number of environments such as those with nonhomogeneous vegetation and terrain. He accounts for the microscopic details of a fire with macroscopic resolution by dividing quantities into mean andmore » fluctuating parts similar to what is done in traditional turbulence modeling. These divided quantities include fuel, wind, gas concentrations, and temperature. Reaction rates are limited by the mixing process and not the chemical kinetics. The author has developed a model that includes the transport of multiple gas species, such as oxygen and volatile hydrocarbons, and tracks the depletion of various fuels and other stationary solids and liquids. From this model he develops a simplified local burning model with which he performs a number of simulations that demonstrate that he is able to capture the important physics with the transport approach. With this simplified model he is able to pick up the essence of wildfire propagation, including such features as acceleration when transitioning to upsloping terrain, deceleration of fire fronts when they reach downslopes, and crowning in the presence of high winds.« less

Invited review: organic and conventionally produced milk-an evaluation of factors influencing milk composition.

PubMed

Schwendel, B H; Wester, T J; Morel, P C H; Tavendale, M H; Deadman, C; Shadbolt, N M; Otter, D E

2015-02-01

Consumer perception of organic cow milk is associated with the assumption that organic milk differs from conventionally produced milk. The value associated with this difference justifies the premium retail price for organic milk. It includes the perceptions that organic dairy farming is kinder to the environment, animals, and people; that organic milk products are produced without the use of antibiotics, added hormones, synthetic chemicals, and genetic modification; and that they may have potential benefits for human health. Controlled studies investigating whether differences exist between organic and conventionally produced milk have so far been largely equivocal due principally to the complexity of the research question and the number of factors that can influence milk composition. A main complication is that farming practices and their effects differ depending on country, region, year, and season between and within organic and conventional systems. Factors influencing milk composition (e.g., diet, breed, and stage of lactation) have been studied individually, whereas interactions between multiple factors have been largely ignored. Studies that fail to consider that factors other than the farming system (organic vs. conventional) could have caused or contributed to the reported differences in milk composition make it impossible to determine whether a system-related difference exists between organic and conventional milk. Milk fatty acid composition has been a central research area when comparing organic and conventional milk largely because the milk fatty acid profile responds rapidly and is very sensitive to changes in diet. Consequently, the effect of farming practices (high input vs. low input) rather than farming system (organic vs. conventional) determines milk fatty acid profile, and similar results are seen between low-input organic and low-input conventional milks. This confounds our ability to develop an analytical method to distinguish organic from conventionally produced milk and provide product verification. Lack of research on interactions between several influential factors and differences in trial complexity and consistency between studies (e.g., sampling period, sample size, reporting of experimental conditions) complicate data interpretation and prevent us from making unequivocal conclusions. The first part of this review provides a detailed summary of individual factors known to influence milk composition. The second part presents an overview of studies that have compared organic and conventional milk and discusses their findings within the framework of the various factors presented in part one. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Urbanisation, poverty and employment: the large metropolis in the third world.

PubMed

Singh, A

1992-01-01

"The main purpose of this paper is to provide an overall review of the chief analytical as well as economic policy issues in relation to Third World cities in the light of the available theoretical and empirical studies on urbanisation, poverty and employment in the developing countries.... Part I...provides basic information on urbanisation in the Third World...[and] outlines the nature and extent of urban poverty in these large cities and considers the impact of the world economic crisis on the urban poor. Part II of the paper discusses the most important structural features of urbanisation in relation to economic development....Finally, Part III briefly examines policy issues in relation to urbanisation and poverty in the Third World's large cities." excerpt

Reanalysis of Wupus agilis (Early Cretaceous) of Chongqing, China as a Large Avian Trace: Differentiating between Large Bird and Small Non-Avian Theropod Tracks

PubMed Central

Xing, Lida; Buckley, Lisa G.; McCrea, Richard T.; Lockley, Martin G.; Zhang, Jianping; Piñuela, Laura; Klein, Hendrik; Wang, Fengping

2015-01-01

Trace fossils provide the only records of Early Cretaceous birds from many parts of the world. The identification of traces from large avian track-makers is made difficult given their overall similarity in size and tridactyly in comparison with traces of small non-avian theropods. Reanalysis of Wupus agilis from the Early Cretaceous (Aptian-Albian) Jiaguan Formation, one of a small but growing number of known avian-pterosaur track assemblages, of southeast China determines that these are the traces of a large avian track-maker, analogous to extant herons. Wupus, originally identified as the trace of a small non-avian theropod track-maker, is therefore similar in both footprint and trackway characteristics to the Early Cretaceous (Albian) large avian trace Limiavipes curriei from western Canada, and Wupus is reassigned to the ichnofamily Limiavipedidae. The reanalysis of Wupus reveals that it and Limiavipes are distinct from similar traces of small to medium-sized non-avian theropods (Irenichnites, Columbosauripus, Magnoavipes) based on their relatively large footprint length to pace length ratio and higher mean footprint splay, and that Wupus shares enough characters with Limiavipes to be reassigned to the ichnofamily Limiavipedidae. The ability to discern traces of large avians from those of small non-avian theropods provides more data on the diversity of Early Cretaceous birds. This analysis reveals that, despite the current lack of body fossils, large wading birds were globally distributed in both Laurasia and Gondwana during the Early Cretaceous. PMID:25993285

The willingness to donate blood: an empirical analysis of socio-demographic and motivation-related determinants.

PubMed

Tscheulin, Dieter K; Lindenmeier, Jörg

2005-08-01

Since the willingness to donate blood is not very high among large parts of the population, a better understanding of the determinants for the willingness to donate blood is of significant importance. This article is intended to contribute to higher uniformity of results in the context of research on blood donation behaviour. Exploratory factor analysis non-parametric tests are used to accomplish this. Potentially important socio-demographic and motivation-related variables particularly affecting the willingness to donate blood are examined. As an addition to the existing literature, the influence of the individual importance structural of characteristics of blood donation facilities, such as the standard of the facility's medical equipment or the training of the facility's staff, will be tested for its effects on the willingness to donate blood. The analysis will also include the influence of direct or indirect personal involvement on the part of the respondent. The results of the study indicate that typical blood donors are young women or men who are studying or possess a higher level of education. Furthermore, potential blood donors can easily be attracted by pecuniary incentives and word of mouth. Unlike non-donors, potential blood donors are not idle, have no fear of infections due to the donation and want reasonable opening hours of blood donation facilities.

Excitation-emission matrix fluorescence spectroscopy in conjunction with multiway analysis for PAH detection in complex matrices.

PubMed

Nahorniak, Michelle L; Booksh, Karl S

2006-12-01

A field portable, single exposure excitation-emission matrix (EEM) fluorometer has been constructed and used in conjunction with parallel factor analysis (PARAFAC) to determine the sub part per billion (ppb) concentrations of several aqueous polycyclic aromatic hydrocarbons (PAHs), such as benzo(k)fluoranthene and benzo(a)pyrene, in various matrices including aqueous motor oil extract and asphalt leachate. Multiway methods like PARAFAC are essential to resolve the analyte signature from the ubiquitous background in environmental samples. With multiway data and PARAFAC analysis it is shown that reliable concentration determinations can be achieved with minimal standards in spite of the large convoluting fluorescence background signal. Thus, rapid fieldable EEM analyses may prove to be a good screening method for tracking pollutants and prioritizing sampling and analysis by more complete but time consuming and labor intensive EPA methods.

Deliberations and evaluations of approaches, endpoints and paradigms for determining zinc dietary recommendations.

PubMed

Sandstead, H H; Smith, J C

1996-09-01

The work group considered past and future Recommended Dietary Allowances (RDAs) for zinc. Past RDAs were based in large part on metabolic balance data. Balance measurements are technically difficult and it is uncertain that they reflect true requirements. Therefore other methods should be used to determine requirements and the RDA. The best approach at this time is the factorial method. In the future, data from measurements of zinc kinetics, in relation to diet and physiological functions will provide useful insights. Future RDAs should provide for at least three levels of bioavailability: low, moderate and high. Whether adjustments should be made in the RDA to account for life style factors is a matter of philosophy. The importance of the differences (gaps) between the RDA and usual intakes of zinc by persons who are apparently in good health, or between the RDA and other dietary guidelines, is an issue for consideration.

Evaluation of the synoptic and mesoscale predictive capabilities of a mesoscale atmospheric simulation system

NASA Technical Reports Server (NTRS)

Koch, S. E.; Skillman, W. C.; Kocin, P. J.; Wetzel, P. J.; Brill, K.; Keyser, D. A.; Mccumber, M. C.

1983-01-01

The overall performance characteristics of a limited area, hydrostatic, fine (52 km) mesh, primitive equation, numerical weather prediction model are determined in anticipation of satellite data assimilations with the model. The synoptic and mesoscale predictive capabilities of version 2.0 of this model, the Mesoscale Atmospheric Simulation System (MASS 2.0), were evaluated. The two part study is based on a sample of approximately thirty 12h and 24h forecasts of atmospheric flow patterns during spring and early summer. The synoptic scale evaluation results benchmark the performance of MASS 2.0 against that of an operational, synoptic scale weather prediction model, the Limited area Fine Mesh (LFM). The large sample allows for the calculation of statistically significant measures of forecast accuracy and the determination of systematic model errors. The synoptic scale benchmark is required before unsmoothed mesoscale forecast fields can be seriously considered.

CCD and photon-counting photometric observations of asteroids carried out at Padova and Catania observatories

NASA Astrophysics Data System (ADS)

Gandolfi, D.; Cigna, M.; Fulvio, D.; Blanco, C.

2009-01-01

We present the results of observational campaigns of asteroids performed at Asiago Station of Padova Astronomical Observatory and at M.G. Fracastoro Station of Catania Astrophysical Observatory, as part of the large research programme on Solar System minor bodies undertaken since 1979 at the Physics and Astronomy Department of Catania University. Photometric observations of six Main-Belt asteroids (27 Euterpe, 173 Ino, 182 Elsa, 539 Pamina, 849 Ara, and 984 Gretia), one Hungaria (1727 Mette), and two Near-Earth Objects (3199 Nefertiti and 2004 UE) are reported. The first determination of the synodic rotational period of 2004 UE was obtained. For 182 Elsa and 1727 Mette the derived synodic period of 80.23±0.08 and 2.981±0.001h, respectively, represents a significant improvement on the previously published values. For 182 Elsa the first determination of the H-G magnitude relation is also presented.

Class attendance, peer similarity, and academic performance in a large field study

PubMed Central

Bjerre-Nielsen, Andreas; Mones, Enys; Lehmann, Sune; Lassen, David Dreyer

2017-01-01

Identifying the factors that determine academic performance is an essential part of educational research. Existing research indicates that class attendance is a useful predictor of subsequent course achievements. The majority of the literature is, however, based on surveys and self-reports, methods which have well-known systematic biases that lead to limitations on conclusions and generalizability as well as being costly to implement. Here we propose a novel method for measuring class attendance that overcomes these limitations by using location and bluetooth data collected from smartphone sensors. Based on measured attendance data of nearly 1,000 undergraduate students, we demonstrate that early and consistent class attendance strongly correlates with academic performance. In addition, our novel dataset allows us to determine that attendance among social peers was substantially correlated (>0.5), suggesting either an important peer effect or homophily with respect to attendance. PMID:29117190

Class attendance, peer similarity, and academic performance in a large field study.

PubMed

Kassarnig, Valentin; Bjerre-Nielsen, Andreas; Mones, Enys; Lehmann, Sune; Lassen, David Dreyer

2017-01-01

Identifying the factors that determine academic performance is an essential part of educational research. Existing research indicates that class attendance is a useful predictor of subsequent course achievements. The majority of the literature is, however, based on surveys and self-reports, methods which have well-known systematic biases that lead to limitations on conclusions and generalizability as well as being costly to implement. Here we propose a novel method for measuring class attendance that overcomes these limitations by using location and bluetooth data collected from smartphone sensors. Based on measured attendance data of nearly 1,000 undergraduate students, we demonstrate that early and consistent class attendance strongly correlates with academic performance. In addition, our novel dataset allows us to determine that attendance among social peers was substantially correlated (>0.5), suggesting either an important peer effect or homophily with respect to attendance.

How cells explore shape space: a quantitative statistical perspective of cellular morphogenesis.

PubMed

Yin, Zheng; Sailem, Heba; Sero, Julia; Ardy, Rico; Wong, Stephen T C; Bakal, Chris

2014-12-01

Through statistical analysis of datasets describing single cell shape following systematic gene depletion, we have found that the morphological landscapes explored by cells are composed of a small number of attractor states. We propose that the topology of these landscapes is in large part determined by cell-intrinsic factors, such as biophysical constraints on cytoskeletal organization, and reflects different stable signaling and/or transcriptional states. Cell-extrinsic factors act to determine how cells explore these landscapes, and the topology of the landscapes themselves. Informational stimuli primarily drive transitions between stable states by engaging signaling networks, while mechanical stimuli tune, or even radically alter, the topology of these landscapes. As environments fluctuate, the topology of morphological landscapes explored by cells dynamically adapts to these fluctuations. Finally we hypothesize how complex cellular and tissue morphologies can be generated from a limited number of simple cell shapes. © 2014 WILEY Periodicals, Inc.

A bibliographical surveys of large-scale systems

NASA Technical Reports Server (NTRS)

Corliss, W. R.

1970-01-01

A limited, partly annotated bibliography was prepared on the subject of large-scale system control. Approximately 400 references are divided into thirteen application areas, such as large societal systems and large communication systems. A first-author index is provided.

Engine Development Design Margins Briefing Charts

NASA Technical Reports Server (NTRS)

Bentz, Chuck

2006-01-01

New engines experience durability problems after entering service. The most prevalent and costly is the hot section, particularly the high-pressure turbine. The origin of durability problems can be traced back to: 1) the basic aero-mechanical design systems, assumptions, and design margins used by the engine designers, 2) the available materials systems, and 3) to a large extent, aggressive marketing in a highly competitive environment that pushes engine components beyond the demonstrated capability of the basic technology available for the hardware designs. Unfortunately the user must operate the engine in the service environment in order to learn the actual thrust loading and the time at max effort take-off conditions used in service are needed to determine the hot section life. Several hundred thousand hours of operational service will be required before the demonstrated reliability of a fleet of engines or the design deficiencies of the engine hot section parts can be determined. Also, it may take three to four engine shop visits for heavy maintenance on the gas path hardware to establish cost effective build standards. Spare parts drive the oerator's engine maintenance costs but spare parts also makes lots of money for the engine manufacturer during the service life of an engine. Unless competition prevails for follow-on engine buys, there is really no motivation for an OEM to spend internal money to improve parts durability and reduce earnings derived from a lucrative spare parts business. If the hot section life is below design goals or promised values, the OEM migh argue that the engine is being operated beyond its basic design intent. On the other hand, the airframer and the operator will continue to remind the OEM that his engine was selected based on a lot of promises to deliver spec thrust with little impact on engine service life if higher thrust is used intermittently. In the end, a standoff prevails and nothing gets fixed. This briefing will propose ways to hold competing engine manufacturers more accountable for engine hot section design margins during the entire Engine Development process as well as provide tools to assess the design temperature margins in the hot section parts of Service Engines.

ERUPTING FILAMENTS WITH LARGE ENCLOSING FLUX TUBES AS SOURCES OF HIGH-MASS THREE-PART CMEs, AND ERUPTING FILAMENTS IN THE ABSENCE OF ENCLOSING FLUX TUBES AS SOURCES OF LOW-MASS UNSTRUCTURED CMEs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hutton, Joe; Morgan, Huw, E-mail: joh9@aber.ac.uk

2015-11-01

The 3-part appearance of many coronal mass ejections (CMEs) arising from erupting filaments emerges from a large magnetic flux tube structure, consistent with the form of the erupting filament system. Other CMEs arising from erupting filaments lack a clear 3-part structure and reasons for this have not been researched in detail. This paper aims to further establish the link between CME structure and the structure of the erupting filament system and to investigate whether CMEs which lack a 3-part structure have different eruption characteristics. A survey is made of 221 near-limb filament eruptions observed from 2013 May 03 to 2014more » June 30 by Extreme UltraViolet (EUV) imagers and coronagraphs. Ninety-two filament eruptions are associated with 3-part structured CMEs, 41 eruptions are associated with unstructured CMEs. The remaining 88 are categorized as failed eruptions. For 34% of the 3-part CMEs, processing applied to EUV images reveals the erupting front edge is a pre-existing loop structure surrounding the filament, which subsequently erupts with the filament to form the leading bright front edge of the CME. This connection is confirmed by a flux-rope density model. Furthermore, the unstructured CMEs have a narrower distribution of mass compared to structured CMEs, with total mass comparable to the mass of 3-part CME cores. This study supports the interpretation of 3-part CME leading fronts as the outer boundaries of a large pre-existing flux tube. Unstructured (non 3-part) CMEs are a different family to structured CMEs, arising from the eruption of filaments which are compact flux tubes in the absence of a large system of enclosing closed field.« less

Uncovering the determinants of a highly perturbed tyrosine pKa in the active site of ketosteroid isomerase.

PubMed

Schwans, Jason P; Sunden, Fanny; Gonzalez, Ana; Tsai, Yingssu; Herschlag, Daniel

2013-11-05

Within the idiosyncratic enzyme active-site environment, side chain and ligand pKa values can be profoundly perturbed relative to their values in aqueous solution. Whereas structural inspection of systems has often attributed perturbed pKa values to dominant contributions from placement near charged groups or within hydrophobic pockets, Tyr57 of a Pseudomonas putida ketosteroid isomerase (KSI) mutant, suggested to have a pKa perturbed by nearly 4 units to 6.3, is situated within a solvent-exposed active site devoid of cationic side chains, metal ions, or cofactors. Extensive comparisons among 45 variants with mutations in and around the KSI active site, along with protein semisynthesis, (13)C NMR spectroscopy, absorbance spectroscopy, and X-ray crystallography, was used to unravel the basis for this perturbed Tyr pKa. The results suggest that the origin of large energetic perturbations are more complex than suggested by visual inspection. For example, the introduction of positively charged residues near Tyr57 raises its pKa rather than lowers it; this effect, and part of the increase in the Tyr pKa from the introduction of nearby anionic groups, arises from accompanying active-site structural rearrangements. Other mutations with large effects also cause structural perturbations or appear to displace a structured water molecule that is part of a stabilizing hydrogen-bond network. Our results lead to a model in which three hydrogen bonds are donated to the stabilized ionized Tyr, with these hydrogen-bond donors, two Tyr side chains, and a water molecule positioned by other side chains and by a water-mediated hydrogen-bond network. These results support the notion that large energetic effects are often the consequence of multiple stabilizing interactions rather than a single dominant interaction. Most generally, this work provides a case study for how extensive and comprehensive comparisons via site-directed mutagenesis in a tight feedback loop with structural analysis can greatly facilitate our understanding of enzyme active-site energetics. The extensive data set provided may also be a valuable resource for those wishing to extensively test computational approaches for determining enzymatic pKa values and energetic effects.

Uncovering the Determinants of a Highly Perturbed Tyrosine pKa in the Active Site of Ketosteroid Isomerase†

PubMed Central

Schwans, Jason P.; Sunden, Fanny; Gonzalez, Ana; Tsai, Yingssu; Herschlag, Daniel

2013-01-01

Within the idiosyncratic enzyme active site environment, side chain and ligand pKa values can be profoundly perturbed relative to their values in aqueous solution. Whereas structural inspection of systems has often attributed perturbed pKa values to dominant contributions from placement near to charged groups or within hydrophobic pockets, Tyr57 of a P. putida ketosteroid isomerase (KSI) mutant, suggested to have a pKa perturbed by nearly 4 units to 6.3, is situated within a solvent-exposed active site devoid of cationic side chains, metal ions, or cofactors. Extensive comparisons among 45 variants with mutations in and around the KSI active site, along with protein semi-synthesis, 13C NMR spectroscopy, absorbance spectroscopy, and x-ray crystallography, was used to unravel the basis for this perturbed Tyr pKa. The results suggest that the origin of large energetic perturbations are more complex than suggested by visual inspection. For example, the introduction of positively charged residues near Tyr57 raises its pKa rather than lowers it; this effect, and part of the increase in the Tyr pKa from introduction of nearby anionic groups arise from accompanying active site structural rearrangements. Other mutations with large effects also cause structural perturbations or appear to displace a structured water molecule that is part of a stabilizing hydrogen bond network. Our results lead to a model in which three hydrogen bonds are donated to the stabilized ionized Tyr, with these hydrogen bond donors, two Tyr side chains and a water molecule, positioned by other side chains and by a water-mediated hydrogen bond network. These results support the notion that large energetic effects are often the consequence of multiple stabilizing interactions, rather than a single dominant interaction. Most generally, this work provides a case study for how extensive and comprehensive comparisons via site-directed mutagenesis in a tight feedback loop with structural analysis can greatly facilitate our understanding of enzyme active site energetics. The extensive dataset provided may also be a valuable resource for those wishing to extensively test computational approaches for determining enzymatic pKa values and energetic effects. PMID:24151972

Transport processes near coastal ocean outfalls

USGS Publications Warehouse

Noble, M.A.; Sherwood, C.R.; Lee, Hooi-Ling; Xu, Jie; Dartnell, P.; Robertson, G.; Martini, M.

2001-01-01

The central Southern California Bight is an urbanized coastal ocean where complex topography and largescale atmospheric and oceanographic forcing has led to numerous sediment-distribution patterns. Two large embayments, Santa Monica and San Pedro Bays, are connected by the short, very narrow shelf off the Palos Verdes peninsula. Ocean-sewage outfalls are located in the middle of Santa Monica Bay, on the Palos Verdes shelf and at the southeastern edge of San Pedro Bay. In 1992, the US Geological Survey, together with allied agencies, began a series of programs to determine the dominant processes that transport sediment and associated pollutants near the three ocean outfalls. As part of these programs, arrays of instrumented moorings that monitor currents, waves, water clarity, water density and collect resuspended materials were deployed on the continental shelf and slope information was also collected on the sediment and contaminant distributions in the region. The data and models developed for the Palos Verdes shelf suggest that the large reservoir of DDT/DDE in the coastal ocean sediments will continue to be exhumed and transported along the shelf for a long time. On the Santa Monica shelf, very large internal waves, or bores, are generated at the shelf break. The near-bottom currents associated with these waves sweep sediments and the associated contaminants from the shelf onto the continental slope. A new program underway on the San Pedro shelf will determine if water and contaminants from a nearby ocean outfall are transported to the local beaches by coastal ocean processes. The large variety of processes found that transport sediments and contaminants in this small region of the continental margin suggest that in regions with complex topography, local processes change markedly over small spatial scales. One cannot necessarily infer that the dominant transport processes will be similar even in adjacent regions.

Global Climate Forcing from Albedo Change Caused by Large-scale Deforestation and Reforestation: Quantification and Attribution of Geographic Variation

NASA Technical Reports Server (NTRS)

Gao, Feng; Ghimire, Bardan; Jiao, Tong; Williams, Christopher A.; Masek, Jeffrey; Schaaf, Crystal

2017-01-01

Large-scale deforestation and reforestation have contributed substantially to historical and contemporary global climate change in part through albedo-induced radiative forcing, with meaningful implications for forest management aiming to mitigate climate change. Associated warming or cooling varies widely across the globe due to a range of factors including forest type, snow cover, and insolation, but resulting geographic variation remain spoorly described and has been largely based on model assessments. This study provides an observation-based approach to quantify local and global radiative forcings from large-scale deforestation and reforestation and further examines mechanisms that result in the spatial heterogeneity of radiative forcing. We incorporate a new spatially and temporally explicit land cover-specific albedo product derived from Moderate Resolution Imaging Spectroradiometer with a historical land use data set (Land Use Harmonization product). Spatial variation in radiative forcing was attributed to four mechanisms, including the change in snow-covered albedo, change in snow-free albedo, snow cover fraction, and incoming solar radiation. We find an albedo-only radiative forcing (RF) of -0.819 W m(exp -2) if year 2000 forests were completely deforested and converted to croplands. Albedo RF from global reforestation of present-day croplands to recover year 1700 forests is estimated to be 0.161 W m)exp -2). Snow-cover fraction is identified as the primary factor in determining the spatial variation of radiative forcing in winter, while the magnitude of the change in snow-free albedo is the primary factor determining variations in summertime RF. Findings reinforce the notion that, for conifers at the snowier high latitudes, albedo RF diminishes the warming from forest loss and the cooling from forest gain more so than for other forest types, latitudes, and climate settings.

Epoxy blanket protects milled part during explosive forming

NASA Technical Reports Server (NTRS)

1966-01-01

Epoxy blanket protects chemically milled or machined sections of large, complex structural parts during explosive forming. The blanket uniformly covers all exposed surfaces and fills any voids to support and protect the entire part.

Debris flow hazards in plantation forests in New Zealand: what we know and need to know

NASA Astrophysics Data System (ADS)

Phillips, Chris; Basher, Les; Marden, Michael; Harrison, Duncan; Heaphy, Marie

2015-04-01

In recent years, extensive storm-induced landsliding has mobilised woody residue during or after plantation forest harvesting and caused debris flows that have affected houses, roads and bridges downstream of forests in several parts of New Zealand. In part, this relates to increasing levels of harvesting activity as many plantations originally planted for soil conservation purposes have reached merchantable size but could also be in response to an increasing incidence of high intensity storms affecting parts of New Zealand. In several cases these incidents have featured on national television and in newspaper headlines with members of the public complaining about the consequences of forestry operations on steep erodible hill country. Forestry companies have responded by developing more detailed environmental impact assessment and erosion and sediment control planning approaches, and by assisting with clean-up operations. Similarly regional councils (the regulatory bodies) have looked more closely at the environmental impacts of forest harvesting and some have modified erosion and sediment control guidelines, previously largely applied to urban earthworks, for forestry application. As part of a wider research programme that aims to raise the profitability and improve the sustainability of New Zealand's forestry sector, we collected information from both forestry companies and regional and unitary councils via survey and interviews to determine the size and scope of the issue, how individual forest companies were identifying and managing the risk, and to determine if national threshold conditions or standards could be established. Even with risk management and good management practices in place, it will not be possible to entirely avoid slope failures and debris flows following harvesting in the future. Thus the need to determine a national level of understanding of what can and can't be managed for is important to allow the development of risk management approaches that all parties can agree with. This paper reports preliminary survey results and discusses company-, regional-, and national-level approaches to begin to address how this issue might be approached in the future on steep eroding hill country in New Zealand.

Ordering Unstructured Meshes for Sparse Matrix Computations on Leading Parallel Systems

NASA Technical Reports Server (NTRS)

Oliker, Leonid; Li, Xiaoye; Heber, Gerd; Biswas, Rupak

2000-01-01

The ability of computers to solve hitherto intractable problems and simulate complex processes using mathematical models makes them an indispensable part of modern science and engineering. Computer simulations of large-scale realistic applications usually require solving a set of non-linear partial differential equations (PDES) over a finite region. For example, one thrust area in the DOE Grand Challenge projects is to design future accelerators such as the SpaHation Neutron Source (SNS). Our colleagues at SLAC need to model complex RFQ cavities with large aspect ratios. Unstructured grids are currently used to resolve the small features in a large computational domain; dynamic mesh adaptation will be added in the future for additional efficiency. The PDEs for electromagnetics are discretized by the FEM method, which leads to a generalized eigenvalue problem Kx = AMx, where K and M are the stiffness and mass matrices, and are very sparse. In a typical cavity model, the number of degrees of freedom is about one million. For such large eigenproblems, direct solution techniques quickly reach the memory limits. Instead, the most widely-used methods are Krylov subspace methods, such as Lanczos or Jacobi-Davidson. In all the Krylov-based algorithms, sparse matrix-vector multiplication (SPMV) must be performed repeatedly. Therefore, the efficiency of SPMV usually determines the eigensolver speed. SPMV is also one of the most heavily used kernels in large-scale numerical simulations.

Variability in the composition of phenolic compounds in winter-dormant Salix pyrolifolia in relation to plant part and age.

PubMed

Lavola, Anu; Maukonen, Merja; Julkunen-Tiitto, Riitta

2018-06-12

The phenolic phytochemicals of winter-dormant Salix pyrolifolia were determined from the vegetative buds, and the bark and wood of different-aged twigs by HPLC-DAD and UHPLC-QTOF-MS analyses. All the plant parts were composed of salicylate glucosides and the other Salix-specific, simple phenolic glucosides as well as of phenolic acids, flavonoids and the high molecular-weight condensed tannins. The flavonoid composition was most diverse in buds and they also contained a large amount of chlorogenic acid (5-caffeoylquinic acid IUPAC), while salicylate glucosides and simple phenolic glucosides predominated in bark. The wooden interior part of the twigs contained fewer components and the lowest concentrations of compounds. Salicortin was the main compound in winter-dormant S. pyrolifolia (over 10% of bark biomass), but the concentrations of picein, salireposide, isosalipurposide, catechin and condensed tannins were also high. The flavonoid composition was highly naringenin- and quercetin-biassed. The composition of phytochemicals was organ-specific and remained relatively similar between different-aged trees. However, there were compound-specific fluctuations in the concentrations of phytochemicals with the age of the trees and within plant parts. Generally, the one-year-old plants differed from the older trees in their high concentration of condensed tannins in all the plant parts studied and in the highest concentration of isosalipurposide in bark, while the total amounts of salicylate glucosides in plant parts, and of naringenin glucosides in buds, tended to be highest in 20 year-old-trees. Copyright © 2018 Elsevier Ltd. All rights reserved.

Determination of the Boltzmann constant by dielectric-constant gas thermometry

NASA Astrophysics Data System (ADS)

Fellmuth, Bernd; Fischer, Joachim; Gaiser, Christof; Jusko, Otto; Priruenrom, Tasanee; Sabuga, Wladimir; Zandt, Thorsten

2011-10-01

Within an international project directed to the new definition of the base unit kelvin, the Boltzmann constant k has been determined by dielectric-constant gas thermometry at PTB. In the pressure range from about 1 MPa to 7 MPa, 11 helium isotherms have been measured at the triple point of water (TPW) by applying a new special experimental setup consisting of a large-volume thermostat, a vacuum-isolated measuring system, stainless-steel 10 pF cylindrical capacitors, an autotransformer ratio capacitance bridge, a high-purity gas-handling system including a mass spectrometer, and traceably calibrated special pressure balances with piston-cylinder assemblies having effective areas of 2 cm2. The value of k has been deduced from the linear, ideal-gas term of an appropriate virial expansion fitted to the combined isotherms. A detailed uncertainty budget has been established by performing Monte Carlo simulations. The main uncertainty components result from the measurement of pressure and capacitance as well as the influence of the effective compressibility of the measuring capacitor and impurities contained in the helium gas. The combination of the results obtained at the TPW (kTPW = 1.380 654 × 10-23 J K-1, relative standard uncertainty 9.2 parts per million) with data measured earlier at low temperatures (21 K to 27 K, kLT = 1.380 657 × 10-23 J K-1, 15.9 parts per million) has yielded a value of k = 1.380 655 × 10-23 J K-1 with uncertainty of 7.9 parts per million.

Large forging manufacturing process

DOEpatents

Thamboo, Samuel V.; Yang, Ling

2002-01-01

A process for forging large components of Alloy 718 material so that the components do not exhibit abnormal grain growth includes the steps of: a) providing a billet with an average grain size between ASTM 0 and ASTM 3; b) heating the billet to a temperature of between 1750.degree. F. and 1800.degree. F.; c) upsetting the billet to obtain a component part with a minimum strain of 0.125 in at least selected areas of the part; d) reheating the component part to a temperature between 1750.degree. F. and 1800.degree. F.; e) upsetting the component part to a final configuration such that said selected areas receive no strains between 0.01 and 0.125; f) solution treating the component part at a temperature of between 1725.degree. F. and 1750.degree. F.; and g) aging the component part over predetermined times at different temperatures. A modified process achieves abnormal grain growth in selected areas of a component where desirable.

77 FR 58953 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Control Technique...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-25

... Promulgation of Air Quality Implementation Plans; Delaware; Control Technique Guidelines for Plastic Parts... categories: Plastic Parts, Metal Furniture, Large Appliances, and Miscellaneous Metal Parts. EPA is approving... Compounds, sections 2.0 ``Definitions,'' 12.0 ``Surface Coating of Plastic Parts,'' 19.0 ``Coating of Metal...

20 CFR 30.805 - What evidence does OWCP use to determine a covered Part E employee's average annual wage and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... covered Part E employee's average annual wage and whether he or she experienced compensable wage-loss... OWCP use to determine a covered Part E employee's average annual wage and whether he or she experienced... the Social Security Administration to establish a covered Part E employee's presumed average annual...

20 CFR 30.805 - What evidence does OWCP use to determine a covered Part E employee's average annual wage and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... covered Part E employee's average annual wage and whether he or she experienced compensable wage-loss... OWCP use to determine a covered Part E employee's average annual wage and whether he or she experienced... the Social Security Administration to establish a covered Part E employee's presumed average annual...

Planning alternative organizational frameworks for a large scale educational telecommunications system served by fixed/broadcast satellites

NASA Technical Reports Server (NTRS)

Walkmeyer, J.

1973-01-01

This memorandum explores a host of considerations meriting attention from those who are concerned with designing organizational structures for development and control of a large scale educational telecommunications system using satellites. Part of a broader investigation at Washington University into the potential uses of fixed/broadcast satellites in U.S. education, this study lays ground work for a later effort to spell out a small number of hypothetical organizational blueprints for such a system and for assessment of potential short and long term impacts. The memorandum consists of two main parts. Part A deals with subjects of system-wide concern, while Part B deals with matters related to specific system components.

Shear-transformation-zone theory of linear glassy dynamics.

PubMed

Bouchbinder, Eran; Langer, J S

2011-06-01

We present a linearized shear-transformation-zone (STZ) theory of glassy dynamics in which the internal STZ transition rates are characterized by a broad distribution of activation barriers. For slowly aging or fully aged systems, the main features of the barrier-height distribution are determined by the effective temperature and other near-equilibrium properties of the configurational degrees of freedom. Our theory accounts for the wide range of relaxation rates observed in both metallic glasses and soft glassy materials such as colloidal suspensions. We find that the frequency-dependent loss modulus is not just a superposition of Maxwell modes. Rather, it exhibits an α peak that rises near the viscous relaxation rate and, for nearly jammed, glassy systems, extends to much higher frequencies in accord with experimental observations. We also use this theory to compute strain recovery following a period of large, persistent deformation and then abrupt unloading. We find that strain recovery is determined in part by the initial barrier-height distribution, but that true structural aging also occurs during this process and determines the system's response to subsequent perturbations. In particular, we find by comparison with experimental data that the initial deformation produces a highly disordered state with a large population of low activation barriers, and that this state relaxes quickly toward one in which the distribution is dominated by the high barriers predicted by the near-equilibrium analysis. The nonequilibrium dynamics of the barrier-height distribution is the most important of the issues raised and left unresolved in this paper.

Modelling and scale-up of chemical flooding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, G.A.; Lake, L.W.; Sepehrnoori, K.

1990-03-01

The objective of this research is to develop, validate, and apply a comprehensive chemical flooding simulator for chemical recovery processes involving surfactants, polymers, and alkaline chemicals in various combinations. This integrated program includes components of laboratory experiments, physical property modelling, scale-up theory, and numerical analysis as necessary and integral components of the simulation activity. We have continued to develop, test, and apply our chemical flooding simulator (UTCHEM) to a wide variety of laboratory and reservoir problems involving tracers, polymers, polymer gels, surfactants, and alkaline agents. Part I is an update on the Application of Higher-Order Methods in Chemical Flooding Simulation.more » This update focuses on the comparison of grid orientation effects for four different numerical methods implemented in UTCHEM. Part II is on Simulation Design Studies and is a continuation of Saad's Big Muddy surfactant pilot simulation study reported last year. Part III reports on the Simulation of Gravity Effects under conditions similar to those of some of the oil reservoirs in the North Sea. Part IV is on Determining Oil Saturation from Interwell Tracers UTCHEM is used for large-scale interwell tracer tests. A systematic procedure for estimating oil saturation from interwell tracer data is developed and a specific example based on the actual field data provided by Sun E P Co. is given. Part V reports on the Application of Vectorization and Microtasking for Reservoir Simulation. Part VI reports on Alkaline Simulation. The alkaline/surfactant/polymer flood compositional simulator (UTCHEM) reported last year is further extended to include reactions involving chemical species containing magnesium, aluminium and silicon as constituent elements. Part VII reports on permeability and trapping of microemulsion.« less

An Assessment of the Intestinal Lumen as a Site for Intervention in Reducing Body Burdens of Organochlorine Compounds

PubMed Central

Jandacek, Ronald J.; Genuis, Stephen J.

2013-01-01

Many individuals maintain a persistent body burden of organochlorine compounds (OCs) as well as other lipophilic compounds, largely as a result of airborne and dietary exposures. Ingested OCs are typically absorbed from the small intestine along with dietary lipids. Once in the body, stored OCs can mobilize from adipose tissue storage sites and, along with circulating OCs, are delivered into the small intestine via hepatic processing and biliary transport. Retained OCs are also transported into both the large and small intestinal lumen via non-biliary mechanisms involving both secretion and desquamation from enterocytes. OCs and some other toxicants can be reabsorbed from the intestine, however, they take part in enterohepatic circulation(EHC). While dietary fat facilitates the absorption of OCs from the small intestine, it has little effect on OCs within the large intestine. Non-absorbable dietary fats and fat absorption inhibitors, however, can reduce the re-absorption of OCs and other lipophiles involved in EHC and may enhance the secretion of these compounds into the large intestine—thereby hastening their elimination. Clinical studies are currently underway to determine the efficacy of using non-absorbable fats and inhibitors of fat absorption in facilitating the elimination of persistent body burdens of OCs and other lipophilic human contaminants. PMID:23476122

An assessment of the intestinal lumen as a site for intervention in reducing body burdens of organochlorine compounds.

PubMed

Jandacek, Ronald J; Genuis, Stephen J

2013-01-01

Many individuals maintain a persistent body burden of organochlorine compounds (OCs) as well as other lipophilic compounds, largely as a result of airborne and dietary exposures. Ingested OCs are typically absorbed from the small intestine along with dietary lipids. Once in the body, stored OCs can mobilize from adipose tissue storage sites and, along with circulating OCs, are delivered into the small intestine via hepatic processing and biliary transport. Retained OCs are also transported into both the large and small intestinal lumen via non-biliary mechanisms involving both secretion and desquamation from enterocytes. OCs and some other toxicants can be reabsorbed from the intestine, however, they take part in enterohepatic circulation(EHC). While dietary fat facilitates the absorption of OCs from the small intestine, it has little effect on OCs within the large intestine. Non-absorbable dietary fats and fat absorption inhibitors, however, can reduce the re-absorption of OCs and other lipophiles involved in EHC and may enhance the secretion of these compounds into the large intestine--thereby hastening their elimination. Clinical studies are currently underway to determine the efficacy of using non-absorbable fats and inhibitors of fat absorption in facilitating the elimination of persistent body burdens of OCs and other lipophilic human contaminants.

Fabrication of TREAT Fuel with Increased Graphite Loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Luther, Erik Paul; Leckie, Rafael M.; Dombrowski, David E.

2014-02-05

As part of the feasibility study exploring the replacement of the HEU fuel core of the TREAT reactor at Idaho National Laboratory with LEU fuel, this study demonstrates that it is possible to increase the graphite content of extruded fuel by reformulation. The extrusion process was use to fabricate the “upgrade” core1 for the TREAT reactor. The graphite content achieved is determined by calculation and has not been measured by any analytical method. In conjunction, a technique, Raman Spectroscopy, has been investigated for measuring the graphite content. This method shows some promise in differentiating between carbon and graphite; however, standardsmore » that would allow the technique to be calibrated to quantify the graphite concentration have yet to be fabricated. Continued research into Raman Spectroscopy is on going. As part of this study, cracking of graphite extrusions due to volatile evolution during heat treatment has been largely eliminated. Continued research to optimize this extrusion method is required.« less

On the Origin of the Double-cell Meridional Circulation in the Solar Convection Zone

NASA Astrophysics Data System (ADS)

Pipin, V. V.; Kosovichev, A. G.

2018-02-01

Recent advances in helioseismology, numerical simulations and mean-field theory of solar differential rotation have shown that the meridional circulation pattern may consist of two or more cells in each hemisphere of the convection zone. According to the mean-field theory the double-cell circulation pattern can result from the sign inversion of a nondiffusive part of the radial angular momentum transport (the so-called Λ-effect) in the lower part of the solar convection zone. Here, we show that this phenomenon can result from the radial inhomogeneity of the Coriolis number, which depends on the convective turnover time. We demonstrate that if this effect is taken into account then the solar-like differential rotation and the double-cell meridional circulation are both reproduced by the mean-field model. The model is consistent with the distribution of turbulent velocity correlations determined from observations by tracing motions of sunspots and large-scale magnetic fields, indicating that these tracers are rooted just below the shear layer.

A suppression hierarchy among competing motor programs drives sequential grooming in Drosophila

PubMed Central

Seeds, Andrew M; Ravbar, Primoz; Chung, Phuong; Hampel, Stefanie; Midgley, Frank M; Mensh, Brett D; Simpson, Julie H

2014-01-01

Motor sequences are formed through the serial execution of different movements, but how nervous systems implement this process remains largely unknown. We determined the organizational principles governing how dirty fruit flies groom their bodies with sequential movements. Using genetically targeted activation of neural subsets, we drove distinct motor programs that clean individual body parts. This enabled competition experiments revealing that the motor programs are organized into a suppression hierarchy; motor programs that occur first suppress those that occur later. Cleaning one body part reduces the sensory drive to its motor program, which relieves suppression of the next movement, allowing the grooming sequence to progress down the hierarchy. A model featuring independently evoked cleaning movements activated in parallel, but selected serially through hierarchical suppression, was successful in reproducing the grooming sequence. This provides the first example of an innate motor sequence implemented by the prevailing model for generating human action sequences. DOI: http://dx.doi.org/10.7554/eLife.02951.001 PMID:25139955

Results of gamma activity traverses made in process tube channels and VSR channels at 105-KW

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greene, M.C. Jr.

1955-02-03

Activity traverses were made at Hanford reactor 105-KW in VSR channels 23, 29, 37, 46, 55, 63 and 69 and in process channels 4669, 4569, 4668, 4670 and 4769. These traverses were made during cleaning operations to assist in the location of any contaminated material in these channels and again after completion of the cleaning operations to determine if all of the contaminated material was removed. Upon completion of the cleaning of the VSR channels and process channels activity traverses were made in all of the channels. The results of these traverses show that no detectable amounts of contaminated materialmore » were present in any of these channels. The traverses made in the VSR channels all show a large peak in the lower part of the pile indicating that the metal in the lower part of the pile received as much as five times the integrated exposure received by the metal in the upper half of the pile. 15 figs.« less

A study of the efficiency of hydrogen liquefaction

NASA Technical Reports Server (NTRS)

Baker, C. R.; Shaner, R. L.

1976-01-01

The use of liquid hydrogen as a jet aircraft fuel has a number of environmental and technological advantages over conventional fuels. The liquefaction of hydrogen requires a large expenditure of energy. There are many inefficiencies that are a part of any practical liquefaction process. Current technology was investigated for the best available system. Parametric studies were made to identify where inefficiencies occur and to optimize and integrate the component parts. Flowsheets are presented for a module that produces 250 tons per day of liquid hydrogen. Approximately ten of these modules is needed for a major airport in the 1990's. The advantages of producing a product with a minimum amount of ortho to para hydrogen conversion are pointed out. The optimum degree of conversion was determined for a liquid hydrogen product that will be used within a given time. An assessment was made regarding the potentials for improvement of the processing schemes and equipment over the next 10 to 25 years.

Generalized ISAR--part II: interferometric techniques for three-dimensional location of scatterers.

PubMed

Given, James A; Schmidt, William R

2005-11-01

This paper is the second part of a study dedicated to optimizing diagnostic inverse synthetic aperture radar (ISAR) studies of large naval vessels. The method developed here provides accurate determination of the position of important radio-frequency scatterers by combining accurate knowledge of ship position and orientation with specialized signal processing. The method allows for the simultaneous presence of substantial Doppler returns from both change of roll angle and change of aspect angle by introducing generalized ISAR ates. The first paper provides two modes of interpreting ISAR plots, one valid when roll Doppler is dominant, the other valid when the aspect angle Doppler is dominant. Here, we provide, for each type of ISAR plot technique, a corresponding interferometric ISAR (InSAR) technique. The former, aspect-angle dominated InSAR, is a generalization of standard InSAR; the latter, roll-angle dominated InSAR, seems to be new to this work. Both methods are shown to be efficient at identifying localized scatterers under simulation conditions.

Statistics of resonances for a class of billiards on the Poincaré half-plane

NASA Astrophysics Data System (ADS)

Howard, P. J.; Mota-Furtado, F.; O'Mahony, P. F.; Uski, V.

2005-12-01

The lower boundary of Artin's billiard on the Poincaré half-plane is continuously deformed to generate a class of billiards with classical dynamics varying from fully integrable to completely chaotic. The quantum scattering problem in these open billiards is described and the statistics of both real and imaginary parts of the resonant momenta are investigated. The evolution of the resonance positions is followed as the boundary is varied which leads to large changes in their distribution. The transition to arithmetic chaos in Artin's billiard, which is responsible for the Poissonian level-spacing statistics of the bound states in the continuum (cusp forms) at the same time as the formation of a set of resonances all with width \\frac{1}{4} and real parts determined by the zeros of Riemann's zeta function, is closely examined. Regimes are found which obey the universal predictions of random matrix theory (RMT) as well as exhibiting non-universal long-range correlations. The Brody parameter is used to describe the transitions between different regimes.

Preliminary Design and Investigation of Integrated Compressor with Composite Material Wheel

NASA Astrophysics Data System (ADS)

Wang, Jifeng; Müller, Norbert

2012-06-01

An integrated water vapor compressor with composite material wheel is developed and strength analysis using FEM is presented. The design of wound composite material allows for integrating all rotating parts of the drive that may simply reduce to only the rotor of the electrical motor, since no drive shaft is required anymore. This design can reduce the number of parts and mass, which is convenient for engineers to maintain the compressor. The electrical motors are brushless DC motors operating through a frequency drive and apply a torque on the wheels through the materials bonded in the wheel shrouds. This system allows a large amount of compression to be produced in a multi-stage compression setup. To determine the stress and vibration characteristics of this integrated compressor, numerical analysis is carried out using FEM. The simulation result shows that the integrated compressor with composite material wheel can be used in a chiller system where water as a refrigerant.

Very large hail occurrence in Poland from 2007 to 2015

NASA Astrophysics Data System (ADS)

Pilorz, Wojciech

2015-10-01

Very large hail is known as a presence of a hailstone greater or equal to 5 cm in diameter. This phenomenon is rare but its significant consequences, not only to agriculture but also to automobiles, households and people outdoor makes it essential thing to examine. Hail appearance is strictly connected with storms frequency and its kind. The most hail-endangered kind of storm is supercell storm. Geographical distribution of hailstorms was compared with geographical distribution of storms in Poland. Similarities were found. The area of the largest number of storms is southeastern Poland. Analyzed European Severe Weather Database (ESWD) data showed that most of very large hail reports occurred in this part of Poland. The probable reason for this situation is the longest period of lasting tropical airmasses in southeastern Poland. Spatial distribution analysis shows also more hail incidents over Upper Silesia, Lesser Poland, Subcarpathia and Świętokrzyskie regions. The information source about hail occurrence was ESWD - open database, where everyone can add report and find reports which meet given search criteria. 69 hailstorms in the period of 2007 - 2015 were examined. They caused 121 very large hail reports. It was found that there is large disproportion in number of hailstorms and hail reports between individual years. Very large hail season in Poland begins in May and ends in September with cumulation in July. Most of hail occurs between 12:00 and 17:00 UTC, but there were some cases of very large (one extremely large) hail at night and early morning hours. However very large hail is a spectacular phenomenon, its local character determines potentially high information loss rate and it is the most significant problem in hail research.

49 CFR 583.6 - Procedure for determining U.S./Canadian parts content.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Procedure for determining U.S./Canadian parts content. 583.6 Section 583.6 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AUTOMOBILE PARTS...

49 CFR 583.6 - Procedure for determining U.S./Canadian parts content.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Procedure for determining U.S./Canadian parts content. 583.6 Section 583.6 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AUTOMOBILE PARTS...

49 CFR 583.6 - Procedure for determining U.S./Canadian parts content.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 7 2014-10-01 2014-10-01 false Procedure for determining U.S./Canadian parts content. 583.6 Section 583.6 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AUTOMOBILE PARTS...

49 CFR 583.6 - Procedure for determining U.S./Canadian parts content.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Procedure for determining U.S./Canadian parts content. 583.6 Section 583.6 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AUTOMOBILE PARTS...

49 CFR 583.6 - Procedure for determining U.S./Canadian parts content.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Procedure for determining U.S./Canadian parts content. 583.6 Section 583.6 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AUTOMOBILE PARTS...

Chemometric approach to evaluate element distribution in muscle, liver and fish bone of roach (Rutilus rutilus), silver bream (Blicca bjoerkna) and crucian carp (Carassius carassius) from Swarzędzkie Lake (Poland) using ICP-MS and FIAS-CVAAS techniques.

PubMed

Chudzińska, Maria; Komorowicz, Izabela; Hanć, Anetta; Gołdyn, Ryszard; Barałkiewicz, Danuta

2016-11-01

The content of elements in fish tissues and organs from Swarzędzkie Lake was investigated in order to evaluate the possible risk associated with their consumption by animals as well as humans. Samples of muscle, liver and fish bone of three fish species; roach (Rutilus rutilus), silver bream (Blicca bjoerkna) and crucian carp (Carassius carassius) were collected from seine catches undertaken as part of the biomanipulation of Swarzędzkie Lake. Element concentration (Al, As, Cd, Co, Cr, Cu, Hg, Ni, Pb, Zn) was determined by inductively coupled plasma mass spectrometry (ICP-MS), with the exception of Hg where the flow injection analysis system cold vapour atomic absorption spectrometry (FIAS-CVAAS) was applied. The study indicated a large variation in the occurrence of the investigated elements in different parts of the fish body. The highest content of Al and Zn was stated in all fish organs for each fish species. The majority of the applied statistical and chemometric methods (e.g., PCA, CA) refer to roach since we had a large number of data for this species. The obtained results were assessed in terms of their accuracy and precision using certified reference material of Fish Muscle ERM BB422.

Assessing the Safety of Vitamin A Delivered Through Large-Scale Intervention Programs: Workshop Report on Setting the Research Agenda.

PubMed

Tanumihardjo, Sherry A; Mokhtar, Najat; Haskell, Marjorie J; Brown, Kenneth H

2016-06-01

Vitamin A (VA) deficiency (VAD) is still a concern in many parts of the world, and multiple intervention strategies are being implemented to reduce the prevalence of VAD and associated morbidity and mortality. Because some individuals within a population may be exposed to multiple VA interventions, concerns have been raised about the possible risk of hypervitaminosis A. A consultative meeting was held in Vienna, Austria, in March 2014 to (1) review current knowledge concerning the safety and effectiveness of large-scale programs to control VAD, (2) develop a related research agenda, and (3) review current available methods to assess VA status and risk of hypervitaminosis A. Multiple countries were represented and shared their experiences using a variety of assessment methods, including retinol isotope dilution (RID) techniques. Discussion included next steps to refine assessment methodology, investigate RID limitations under different conditions, and review programmatic approaches to ensure VA adequacy and avoid excessive intakes. Fortification programs have resulted in adequate VA status in Guatemala, Zambia, and parts of Cameroon. Dietary patterns in several countries revealed that some people may consume excessive preformed VA from fortified foods. Additional studies are needed to compare biomarkers of tissue damage to RID methods during hypervitaminosis A and to determine what other biomarkers can be used to assess excessive preformed VA intake. © The Author(s) 2016.

Measurement of the parity-violating asymmetry in inclusive electroproduction of π - near the Delta 0 resonance

DOE PAGES

Androic, D.; Armstrong, D. S.; Bailey, S. L.; ...

2012-03-20

The parity-violating (PV) asymmetry of inclusive π - production in electron scattering from a liquid deuterium target was measured at backward angles. The measurement was conducted as a part of the G0 experiment, at a beam energy of 360 MeV. The physics process dominating pion production for these kinematics is quasi-free photoproduction off the neutron via the Δ 0 resonance. In the context of heavy-baryon chiral perturbation theory (HBχPT), this asymmetry is related to a low energy constant d Δ - that characterizes the parity-violating γNΔ coupling. Zhu et al. calculated d Δ - in a model benchmarked by themore » large asymmetries seen in hyperon weak radiative decays, and predicted potentially large asymmetries for this process, ranging from A γ - = -5.2 to +5.2 ppm. The measurement performed in this work leads to A γ - = -0.36 ± 1.06 ± 0.37 ± 0.03 ppm (where sources of statistical, systematic and theoretical uncertainties are included), which would disfavor enchancements considered by Zhu et al. proportional to V ud/V us. The measurement is part of a program of inelastic scattering measurements that were conducted by the G0 experiment, seeking to determine the N-Δ axial transition form-factors using PV electron scattering.« less

Titan's diverse landscapes as evidenced by Cassini RADAR's third and fourth looks at Titan

USGS Publications Warehouse

Lunine, J.I.; Elachi, C.; Wall, S.D.; Janssen, M.A.; Allison, M.D.; Anderson, Y.; Boehmer, R.; Callahan, P.; Encrenaz, P.; Flamini, E.; Franceschetti, G.; Gim, Y.; Hamilton, G.; Hensley, S.; Johnson, W.T.K.; Kelleher, K.; Kirk, R.L.; Lopes, R.M.; Lorenz, R.; Muhleman, D.O.; Orosei, R.; Ostro, S.J.; Paganelli, F.; Paillou, P.; Picardi, G.; Posa, F.; Radebaugh, J.; Roth, L.E.; Seu, R.; Shaffer, S.; Soderblom, L.A.; Stiles, B.; Stofan, E.R.; Vetrella, S.; West, R.; Wood, C.A.; Wye, L.; Zebker, H.; Alberti, G.; Karkoschka, E.; Rizk, B.; McFarlane, E.; See, C.; Kazeminejad, B.

2008-01-01

Cassini's third and fourth radar flybys, T7 and T8, covered diverse terrains in the high southern and equatorial latitudes, respectively. The T7 synthetic aperture radar (SAR) swath is somewhat more straightforward to understand in terms of a progressive poleward descent from a high, dissected, and partly hilly terrain down to a low flat plain with embayments and deposits suggestive of the past or even current presence of hydrocarbon liquids. The T8 swath is dominated by dunes likely made of organic solids, but also contain somewhat enigmatic, probably tectonic, features that may be partly buried or degraded by erosion or relaxation in a thin crust. The dark areas in T7 show no dune morphology, unlike the dark areas in T8, but are radiometrically warm like the dunes. The Huygens landing site lies on the edge of the T8 swath; correlation of the radar and Huygens DISR images allows accurate determination of its coordinates, and indicates that to the north of the landing site sit two large longitudinal dunes. Indeed, had the Huygens probe trajectory been just 10 km north of where it actually was, images of large sand dunes would have been returned in place of the fluvially dissected terrain actually seen-illustrating the strong diversity of Titan's landscapes even at local scales. ?? 2008 Elsevier Inc. All rights reserved.

CCD Photometry of Cometary Nuclei, I: Observations from 1990-1995

NASA Astrophysics Data System (ADS)

Licandro, Javier; Tancredi, Gonzalo; Lindgren, Mats; Rickman, Hans; Hutton, Ricardo Gil

2000-09-01

CCD photometry of 18 Jupiter family comets, observed at medium and large heliocentric distances, was carried out between April 1990 and July 1995. This is part of a long-term observational program designed to obtain their nuclear magnitudes. The observations were made with the 1.54-m Danish Telescope at ESO La Silla, the 2.5-m Nordic Optical Telescope (NOT) at Observatorio del Roque de los Muchachos (La Palma), the 2.0-m telescope at Pic du Midi, and the 2.15-m telescope at CASLEO, Argentina. Our estimates of the absolute nuclear magnitudes are discussed in comparison with previous determinations. Estimates (sometimes upper limits) for the effective radius ( R) of the nuclei are computed considering a typical geometric albedo pv=0.04. The lowest radius found is the one of 37P/Forbes ( R=1.0 km) while the largest corresponds to 65P/Gunn ( R=11.0 km), but in this case the comet was observed very active. Wherever possible, cometary image profiles are compared with stellar profiles, in order to determine the existence of a faint coma. Seven of the comets were active, six of them at heliocentric distances larger than 4 AU. This unexpected activity is also discussed. We find a strong correlation between activity at large heliocentric distances and recent downward jumps in perihelion distance.

Presence of global and local α-relaxations in an alkyl phosphate glass former

NASA Astrophysics Data System (ADS)

Wu, Tao; Jin, Xiao; Saini, Manoj K.; Liu, Ying Dan; Ngai, K. L.; Wang, Li-Min

2017-10-01

The dynamics of a molecular glass former, tributyl phosphate (TBP), with an alkyl phosphate structure (three alkyl branches emanating from a polar core of PO4) is studied in the supercooled regime by dielectric and thermal (or enthalpic) relaxations. The dielectric fragility index md and the stretching exponent βd of the Kohlrausch-Williams-Watts correlation function are determined. Analyses of the enthalpic relaxation data by the Tool-Narayanaswamy-Moynihan-Hodge formalism yield the enthalpic fragility index mH and stretching exponent βH. The large difference between the dielectric md and the enthalpic mH, as well as between βd and βH, is a remarkable finding. The differences are interpreted by the formation of molecular self-assemblies. The interpretation is supported by the quite comparable fragility determined by viscosity and the enthalpic relaxation. The Kirkwood factor calculated at low temperatures is also consistent with the interpretation. The results suggest that the enthalpic relaxation involving the motions of all parts of TBP is global, while the dielectric relaxation detects the local rotation, which might originate from the rotation of the dipole moment of the core. The presence of two structural α-relaxations, one global and one local, with a large difference in dynamics is revealed for the first time in a molecular glass former.

UNCOVERING THE INTRINSIC VARIABILITY OF GAMMA-RAY BURSTS

NASA Astrophysics Data System (ADS)

Golkhou, V. Zach; Butler, Nathaniel R

2014-08-01

We develop a robust technique to determine the minimum variability timescale for gamma-ray burst (GRB) light curves, utilizing Haar wavelets. Our approach averages over the data for a given GRB, providing an aggregate measure of signal variation while also retaining sensitivity to narrow pulses within complicated time series. In contrast to previous studies using wavelets, which simply define the minimum timescale in reference to the measurement noise floor, our approach identifies the signature of temporally smooth features in the wavelet scaleogram and then additionally identifies a break in the scaleogram on longer timescales as a signature of a true, temporally unsmooth light curve feature or features. We apply our technique to the large sample of Swift GRB gamma-ray light curves and for the first time—due to the presence of a large number of GRBs with measured redshift—determine the distribution of minimum variability timescales in the source frame. We find a median minimum timescale for long-duration GRBs in the source frame of Δtmin = 0.5 s, with the shortest timescale found being on the order of 10 ms. This short timescale suggests a compact central engine (3000 km). We discuss further implications for the GRB fireball model and present a tantalizing correlation between the minimum timescale and redshift, which may in part be due to cosmological time dilation.

DNA content determination of micronucleated polychromatic erythrocytes induced by clastogens and spindle poisons in mouse bone marrow and peripheral blood

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grawe, J.; Amneus, H.; Zetterberg, G.

1993-01-01

The frequencies and DNA distributions of micronuclei in polychromatic erythrocytes from the bone marrow and peripheral blood of mice after four different treatments were determined by flow cytometry. Polychromatic erthrocytes were detected using the fluorescent RNA stain thiazole orange, while micronuclei were detected with the DNA stain Hoechst 33342. The treatments were X-irradiation (1 Gy), cyclophosphamide (30 mg/kg), vincristine sulfphate (0.08 mg/kg), and cochicine (1 mg/kg). All treatments showed increased frequencies of micronucleated polychromatic erythrocytes at 30h after treatment in the bone marrow (colchicine 50h) and at 50h in the peripheral blood. The clostogenic agents X-irradiation and cyclophosphamide and themore » spindle poisons vincristine sulphate and cochicine could be grouped according to the fluorescent characteristics of the induced micronuclei as well as the relative frequency of small (0.5-2% if the diploid G1 DNA content) and large (2-10%) micronuclei. In the peripheral blood the relative frequency of large micronuclei was lower than in the bone marrow, indicating that they were partly eliminated before entrance into the peripheral circulation. The nature of presumed micronuclei was verified by sorting. The potential of this approach to give information on the mechanism of induction of micronuclei is discussed.« less

A Conformational Transition in the Myosin VI Converter Contributes to the Variable Step Size

PubMed Central

Ovchinnikov, V.; Cecchini, M.; Vanden-Eijnden, E.; Karplus, M.

2011-01-01

Myosin VI (MVI) is a dimeric molecular motor that translocates backwards on actin filaments with a surprisingly large and variable step size, given its short lever arm. A recent x-ray structure of MVI indicates that the large step size can be explained in part by a novel conformation of the converter subdomain in the prepowerstroke state, in which a 53-residue insert, unique to MVI, reorients the lever arm nearly parallel to the actin filament. To determine whether the existence of the novel converter conformation could contribute to the step-size variability, we used a path-based free-energy simulation tool, the string method, to show that there is a small free-energy difference between the novel converter conformation and the conventional conformation found in other myosins. This result suggests that MVI can bind to actin with the converter in either conformation. Models of MVI/MV chimeric dimers show that the variability in the tilting angle of the lever arm that results from the two converter conformations can lead to step-size variations of ∼12 nm. These variations, in combination with other proposed mechanisms, could explain the experimentally determined step-size variability of ∼25 nm for wild-type MVI. Mutations to test the findings by experiment are suggested. PMID:22098742

Turbulent boundary layer over roughness transition with variation in spanwise roughness length scale

NASA Astrophysics Data System (ADS)

Westerweel, Jerry; Tomas, Jasper; Eisma, Jerke; Pourquie, Mathieu; Elsinga, Gerrit; Jonker, Harm

2016-11-01

Both large-eddy simulations (LES) and water-tunnel experiments, using simultaneous stereoscopic PIV and LIF were done to investigate pollutant dispersion in a region where the surface changes from rural to urban roughness. This consists of rectangular obstacles where we vary the spanwise aspect ratio of the obstacles. A line source of passive tracer was placed upstream of the roughness transition. The objectives of the study are: (i) to determine the influence of the aspect ratio on the roughness-transition flow, and (ii) to determine the dominant mechanisms of pollutant removal from street canyons in the transition region. It is found that for a spanwise aspect ratio of 2 the drag induced by the roughness is largest of all considered cases, which is caused by a large-scale secondary flow. In the roughness transition the vertical advective pollutant flux is the main ventilation mechanism in the first three streets. Furthermore, by means of linear stochastic estimation the mean flow structure is identied that is responsible for exchange of the fluid between the roughness obstacles and the outer part of the boundary layer. Furthermore, it is found that the vertical length scale of this structure increases with increasing aspect ratio of the obstacles in the roughness region.

Androgenesis: where males hijack eggs to clone themselves

PubMed Central

2016-01-01

Androgenesis is a form of quasi-sexual reproduction in which a male is the sole source of the nuclear genetic material in the embryo. Two types of androgenesis occur in nature. Under the first type, females produce eggs without a nucleus and the embryo develops from the male gamete following fertilization. Evolution of this type of androgenesis is poorly understood as the parent responsible for androgenesis (the mother) gains no benefit from it. Ultimate factors driving the evolution of the second type of androgenesis are better understood. In this case, a zygote is formed between a male and a female gamete, but the female genome is eliminated. When rare, androgenesis with genome elimination is favoured because an androgenesis-determining allele has twice the reproductive success of an allele that determines sexual reproduction. Paradoxically, except in hermaphrodites, a successful androgenetic strain can drive such a male-biased sex ratio that the population goes extinct. This likely explains why androgenesis with genome elimination appears to be rarer than androgenesis via non-nucleate eggs, although both forms are either very rare or remain largely undetected in nature. Nonetheless, some highly invasive species including ants and freshwater clams are androgenetic, for reasons that are largely unexplained. This article is part of the themed issue ‘Weird sex: the underappreciated diversity of sexual reproduction’. PMID:27619698

Bore-sight calibration of the profile laser scanner using a large size exterior calibration field

NASA Astrophysics Data System (ADS)

Koska, Bronislav; Křemen, Tomáš; Štroner, Martin

2014-10-01

The bore-sight calibration procedure and results of a profile laser scanner using a large size exterior calibration field is presented in the paper. The task is a part of Autonomous Mapping Airship (AMA) project which aims to create s surveying system with specific properties suitable for effective surveying of medium-wide areas (units to tens of square kilometers per a day). As is obvious from the project name an airship is used as a carrier. This vehicle has some specific properties. The most important properties are high carrying capacity (15 kg), long flight time (3 hours), high operating safety and special flight characteristics such as stability of flight, in terms of vibrations, and possibility to flight at low speed. The high carrying capacity enables using of high quality sensors like professional infrared (IR) camera FLIR SC645, high-end visible spectrum (VIS) digital camera and optics in the visible spectrum and tactical grade INSGPS sensor iMAR iTracerRT-F200 and profile laser scanner SICK LD-LRS1000. The calibration method is based on direct laboratory measuring of coordinate offset (lever-arm) and in-flight determination of rotation offsets (bore-sights). The bore-sight determination is based on the minimization of squares of individual point distances from measured planar surfaces.

Another HISA--the new standard: health informatics--service architecture.

PubMed

Klein, Gunnar O; Sottile, Pier Angelo; Endsleff, Frederik

2007-01-01

In addition to the meaning as Health Informatics Society of Australia, HISA is the acronym used for the new European Standard: Health Informatics - Service Architecture. This EN 12967 standard has been developed by CEN - the federation of 29 national standards bodies in Europe. This standard defines the essential elements of a Service Oriented Architecture and a methodology for localization particularly useful for large healthcare organizations. It is based on the Open Distributed Processing (ODP) framework from ISO 10746 and contains the following parts: Part 1: Enterprise viewpoint. Part 2: Information viewpoint. Part 3: Computational viewpoint. This standard is now also the starting point for the consideration for an International standard in ISO/TC 215. The basic principles with a set of health specific middleware services as a common platform for various applications for regional health information systems, or large integrated hospital information systems, are well established following a previous prestandard. Examples of large scale deployments in Sweden, Denmark and Italy are described.

Geochemical Comparison of Four Cores from the Manson Impact Structure

NASA Technical Reports Server (NTRS)

Korotev, Randy L.; Rockow, Kaylynn M.; Jolliff, Bradley L.; Haskin, Larry A.; McCarville, Peter; Crossey, Laura J.

1996-01-01

Concentrations of 33 elements were determined in relatively unaltered, matrix-rich samples of impact breccia at approximately 3-m-depth intervals in the M-1 core from the Manson impact structure, Iowa. In addition, 46 matrix-rich samples from visibly altered regions of the M-7, M-8, and M-10 cores were studied, along with 42 small clasts from all four cores. Major element compositions were determined for a subset of impact breccias from the M-1 core, including matrix-rich impact-melt breccia. Major- and trace-element compositions were also determined for a suite of likely target rocks. In the M-1 core, different breccia units identified from lithologic examination of cores are compositionally distinct. There is a sharp compositional discontinuity at the boundary between the Keweenawan-shale-clast breccia and the underlying unit of impact-melt breccia (IMB) for most elements, suggesting minimal physical mixing between the two units during emplacement. Samples from the 40-m-thick IMB (M-1) are all similar to each other in composition, although there are slight increases in concentration with depth for those elements that have high concentrations in the underlying fragmental-matrix suevite breccia (SB) (e.g., Na, Ca, Fe, Sc), presumably as a result of greater clast proportions at the bottom margin of the unit of impact-melt breccia. The high degree of compositional similarity we observe in the impact-melt breccias supports the interpretation that the matrix of this unit represents impact melt. That our analyses show such compositional similarity results in part from our technique for sampling these breccias: for each sample we analyzed a few small fragments (total mass: approximately 200 mg) selected to be relatively free of large clasts and visible signs of alteration instead of subsamples of powders prepared from a large mass of breccia. The mean composition of the matrix-rich part of impact-melt breccia from the M-1 core can be modeled as a mixture of approximately 35% shale and siltstone (Proterozoic "Red Clastics"), 23% granite, 40% hornblende-biotite gneiss, and a small component (less than 2%) of mafic-dike rocks.

Current Issues in Cosmology

NASA Astrophysics Data System (ADS)

Pecker, Jean-Claude; Narlikar, Jayant

2011-09-01

Part I. Observational Facts Relating to Discrete Sources: 1. The state of cosmology G. Burbidge; 2. The redshifts of galaxies and QSOs E. M. Burbidge and G. Burbidge; 3. Accretion discs in quasars J. Sulentic; Part II. Observational Facts Relating to Background Radiation: 4. CMB observations and consequences F. Bouchet; 5. Abundances of light nuclei K. Olive; 6. Evidence for an accelerating universe or lack of A. Blanchard; Part III. Standard Cosmology: 7. Cosmology, an overview of the standard model F. Bernardeau; 8. What are the building blocks of our universe? K. C. Wali; Part IV. Large-Scale Structure: 9. Observations of large-scale structure V. de Lapparent; 10. Reconstruction of large-scale peculiar velocity fields R. Mohayaee, B. Tully and U. Frisch; Part V. Alternative Cosmologies: 11. The quasi-steady state cosmology J. V. Narlikar; 12. Evidence for iron whiskers in the universe N. C. Wickramasinghe; 13. Alternatives to dark matter: MOND + Mach D. Roscoe; 14. Anthropic principle in cosmology B. Carter; Part VI. Evidence for Anomalous Redshifts: 15. Anomalous redshifts H. C. Arp; 16. Redshifts of galaxies and QSOs: the problem of redshift periodicities G. Burbidge; 17. Statistics of redshift periodicities W. Napier; 18. Local abnormal redshifts J.-C. Pecker; 19. Gravitational lensing and anomalous redshifts J. Surdej, J.-F. Claeskens and D. Sluse; Panel discussion; General discussion; Concluding remarks.

The implementation and preliminary evaluation of an ART strategy in Mexico - a country example

PubMed Central

HERMOSILLO, Vera Heriberto; QUINTERO, Luengas Elisa; GUERRERO, Namihira Delia; SUÁREZ, Díaz Dante Sergio; HERNÁNDEZ, Muñúzuri Jorge Alejandro; HOLMGREN, Christopher J.

2009-01-01

ABSTRACT The massive use of preventive measures in Mexico including fluoride toothpaste, a national program of salt fluoridation and education on prevention has resulted in a large decline in dental caries over the past two decades. There does however remain a largely unmet need for restorative treatment. This paper describes the steps leading up to the adoption of a strategy, as part of general health policy, to use Atraumatic Restorative Treatment (ART) within the Mexican public health service as a means to address this. This included the development of training materials, the organization of training courses for existing dentists and the incorporation of ART into the undergraduate curriculum. Results: Six years after the introduction of ART in the year 2000, it was estimated that over 2 million ART procedures had been provided. As part of the planning cycle, an evaluation was undertaken in 2008 to determine amongst Mexican dentists what were the perceived problems when implementing the ART approach. Such research identified that the scarcity of appropriate dental materials and the lack of suitable instruments were the major problems. In addition, a preliminary evaluation of ART restorations and sealants placed as part of this National Oral Health Program was undertaken. The survival outcomes after one year compared favorably with one other study conducted in Mexico but were somewhat lower than the results reported from a number of other countries. Conclusion: The ambitious and forward thinking policy for improving the oral health in Mexico is now showing dividends. One example is the ART strategy, which has been successful both in terms of the number of ART procedures provided and generally in terms of clinical outcomes. PMID:21499665

Granularity in the magnetic field structure of M83

NASA Technical Reports Server (NTRS)

Allen, R. J.; Sukumar, S.

1990-01-01

Researchers recently reported Very Large Array (VLA) 20 cm continuum polarization observations of the bright, nearly face-on southern spiral galaxy M83 (NGC 5236) at a spatial resolution of 2 kpc (Sukumar and Allen 1989). The strongest linearly-polarized emission is found in two giant arcs, with typical lengths of about 30 kpc, which are situated roughly opposite each other in the dark outer regions of the galaxy at a radius of 12 kpc from the center. These regions of high polarized intensity (and hence highly-uniform magnetic field) do not coincide with any prominent spiral-arm tracers, in contrast to the expectations of simple models for the large-scale compression of magnetic field in density-wave shock fronts. From a comparison of the data with previous results at 6 cm, the authors concluded that the low polarization in the central regions of the galaxy is a result of disorder in the interstellar magnetic field. The most likely cause of this disorder is the greater star formation activity observed in the inner parts of the galaxy. The intrinsic direction of the magnetic field in the outer parts of the galaxy has also recently been determined on a length scale of 6.5 kpc from a comparison of the VLA 20 cm results with 6.3 cm observations obtained earlier with the Effelsberg telescope (Sukumar et al. 1989). There is very little Faraday rotation in the regions of the highly-polarized arcs of emission. The magnetic field in these polarized arcs is parallel to the general spiral arm structure seen in the usual optical tracers (dust, HII regions) in the bright inner parts of the galaxy disk. The maximum observed polarization at 2 kpc resolution is about 50 percent.

The implementation and preliminary evaluation of an ART strategy in Mexico: a country example.

PubMed

Hermosillo, Vera Heriberto; Quintero, Luengas Elisa; Guerrero, Namihira Delia; Suárez, Díaz Dante Sergio; Hernández, Muñúzuri Jorge Alejandro; Holmgren, Christopher J

2009-01-01

The massive use of preventive measures in Mexico including fluoride toothpaste, a national program of salt fluoridation and education on prevention has resulted in a large decline in dental caries over the past two decades. There does however remain a largely unmet need for restorative treatment. This paper describes the steps leading up to the adoption of a strategy, as part of general health policy, to use Atraumatic Restorative Treatment (ART) within the Mexican public health service as a means to address this. This included the development of training materials, the organization of training courses for existing dentists and the incorporation of ART into the undergraduate curriculum. Six years after the introduction of ART in the year 2000, it was estimated that over 2 million ART procedures had been provided. As part of the planning cycle, an evaluation was undertaken in 2008 to determine amongst Mexican dentists what were the perceived problems when implementing the ART approach. Such research identified that the scarcity of appropriate dental materials and the lack of suitable instruments were the major problems. In addition, a preliminary evaluation of ART restorations and sealants placed as part of this National Oral Health Program was undertaken. The survival outcomes after one year compared favorably with one other study conducted in Mexico but were somewhat lower than the results reported from a number of other countries. The ambitious and forward thinking policy for improving the oral health in Mexico is now showing dividends. One example is the ART strategy, which has been successful both in terms of the number of ART procedures provided and generally in terms of clinical outcomes.

New business opportunity: Green field project with new technology

NASA Astrophysics Data System (ADS)

Lee, Seung Jae; Woo, Jong Hun; Shin, Jong Gye

2014-06-01

Since 2009 of global financial crisis, shipbuilding industry has undergone hard times seriously. After such a long depression, the latest global shipping market index shows that the economic recovery of global shipbuilding market is underway. Especially, nations with enormous resources are going to increase their productivity or expanding their shipyards to accommodate a large amount of orders expected in the near future. However, few commercial projects have been carried out for the practical shipyard layout designs even though those can be good commercial opportunities for shipbuilding engineers. Shipbuilding starts with a shipyard construction with a large scale investment initially. Shipyard design and the equipment layout problem, which is directly linked to the productivity of ship production, is an important issue in the production planning of mass production of ships. In many cases, shipbuilding yard design has relied on the experience of the internal engineer, resulting in sporadic and poorly organized processes. Consequently, economic losses and the trial and error involved in such a design process are inevitable problems. The starting point of shipyard construction is to design a shipyard layout. Four kinds of engineering parts required for the shipyard layout design and construction. Those are civil engineering, building engineering, utility engineering and production layout engineering. Among these parts, production layout engineering is most important because its result is used as a foundation of the other engineering parts, and also, determines the shipyard capacity in the shipyard lifecycle. In this paper, the background of shipbuilding industry is explained in terms of engineering works for the recognition of the macro trend. Nextly, preliminary design methods and related case study is introduced briefly by referencing the previous research. Lastly, the designed work of layout design is validated using the computer simulation technology.

An advanced method to assess the diet of free-ranging large carnivores based on scats.

PubMed

Wachter, Bettina; Blanc, Anne-Sophie; Melzheimer, Jörg; Höner, Oliver P; Jago, Mark; Hofer, Heribert

2012-01-01

The diet of free-ranging carnivores is an important part of their ecology. It is often determined from prey remains in scats. In many cases, scat analyses are the most efficient method but they require correction for potential biases. When the diet is expressed as proportions of consumed mass of each prey species, the consumed prey mass to excrete one scat needs to be determined and corrected for prey body mass because the proportion of digestible to indigestible matter increases with prey body mass. Prey body mass can be corrected for by conducting feeding experiments using prey of various body masses and fitting a regression between consumed prey mass to excrete one scat and prey body mass (correction factor 1). When the diet is expressed as proportions of consumed individuals of each prey species and includes prey animals not completely consumed, the actual mass of each prey consumed by the carnivore needs to be controlled for (correction factor 2). No previous study controlled for this second bias. Here we use an extended series of feeding experiments on a large carnivore, the cheetah (Acinonyx jubatus), to establish both correction factors. In contrast to previous studies which fitted a linear regression for correction factor 1, we fitted a biologically more meaningful exponential regression model where the consumed prey mass to excrete one scat reaches an asymptote at large prey sizes. Using our protocol, we also derive correction factor 1 and 2 for other carnivore species and apply them to published studies. We show that the new method increases the number and proportion of consumed individuals in the diet for large prey animals compared to the conventional method. Our results have important implications for the interpretation of scat-based studies in feeding ecology and the resolution of human-wildlife conflicts for the conservation of large carnivores.

An Advanced Method to Assess the Diet of Free-Ranging Large Carnivores Based on Scats

PubMed Central

Wachter, Bettina; Blanc, Anne-Sophie; Melzheimer, Jörg; Höner, Oliver P.; Jago, Mark; Hofer, Heribert

2012-01-01

Background The diet of free-ranging carnivores is an important part of their ecology. It is often determined from prey remains in scats. In many cases, scat analyses are the most efficient method but they require correction for potential biases. When the diet is expressed as proportions of consumed mass of each prey species, the consumed prey mass to excrete one scat needs to be determined and corrected for prey body mass because the proportion of digestible to indigestible matter increases with prey body mass. Prey body mass can be corrected for by conducting feeding experiments using prey of various body masses and fitting a regression between consumed prey mass to excrete one scat and prey body mass (correction factor 1). When the diet is expressed as proportions of consumed individuals of each prey species and includes prey animals not completely consumed, the actual mass of each prey consumed by the carnivore needs to be controlled for (correction factor 2). No previous study controlled for this second bias. Methodology/Principal Findings Here we use an extended series of feeding experiments on a large carnivore, the cheetah (Acinonyx jubatus), to establish both correction factors. In contrast to previous studies which fitted a linear regression for correction factor 1, we fitted a biologically more meaningful exponential regression model where the consumed prey mass to excrete one scat reaches an asymptote at large prey sizes. Using our protocol, we also derive correction factor 1 and 2 for other carnivore species and apply them to published studies. We show that the new method increases the number and proportion of consumed individuals in the diet for large prey animals compared to the conventional method. Conclusion/Significance Our results have important implications for the interpretation of scat-based studies in feeding ecology and the resolution of human-wildlife conflicts for the conservation of large carnivores. PMID:22715373

33 CFR Appendix C to Part 157 - Procedure for Determining Distribution of Segregated Ballast Tanks To Provide Protection Against...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Ramming, or Collision C Appendix C to Part 157 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... VESSELS CARRYING OIL IN BULK Pt. 157, App. C Appendix C to Part 157—Procedure for Determining Distribution...

33 CFR Appendix C to Part 157 - Procedure for Determining Distribution of Segregated Ballast Tanks To Provide Protection Against...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Ramming, or Collision C Appendix C to Part 157 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... VESSELS CARRYING OIL IN BULK Pt. 157, App. C Appendix C to Part 157—Procedure for Determining Distribution...

14 CFR 21.27 - Issue of type certificate: surplus aircraft of the Armed Forces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 1 Small reciprocating-engine powered airplanes Before May 16, 1956After May 15, 1956 CAR Part 3, as effective May 15, 1956.CAR Part 3, or FAR Part 23. Small turbine engine-powered airplanes Before Oct. 2... Part 25. Large turbine engine-powered airplanes Before Oct. 2, 1959After Oct. 1, 1959 CAR Part 4b, as...

The interplanetary magnetic field B[sub y] effects on large-scale field-aligned currents near local noon: Contributions from cusp part and noncusp part

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamauchi, M.; Lundin, R.; Woch, J.

1993-04-01

latitudinals develop a model to account for the effect of the interplanetary magnetic field (IMF) B[sub y] component on the dayside field-aligned currents (FACs). As part of the model the FACs are divided into a [open quotes]cusp part[close quotes] and a [open quotes]noncusp part[close quotes]. The authors then propose that the cusp part FACs shift in the longitudinal direction while the noncusplike part FACs shift in both longitudinal and latitudinal directions in response to the y component of the IMF. If combined, it is observed that the noncusp part FAC is found poleward of the cusp part FAC system whenmore » the y component of the IMF is large. These two FAC systems flow in the same direction. They reinforce one another, creating a strong FAC, termed the DPY-FAC. The model also predicts that the polewardmost part of the DPY-FAC flows on closed field lines, even in regions conventionally occupied by the polar cap. Results of the model are successfully compared with particle and magnetic field data from Viking missions.« less

Spatial selective attention in a complex auditory environment such as polyphonic music.

PubMed

Saupe, Katja; Koelsch, Stefan; Rübsamen, Rudolf

2010-01-01

To investigate the influence of spatial information in auditory scene analysis, polyphonic music (three parts in different timbres) was composed and presented in free field. Each part contained large falling interval jumps in the melody and the task of subjects was to detect these events in one part ("target part") while ignoring the other parts. All parts were either presented from the same location (0 degrees; overlap condition) or from different locations (-28 degrees, 0 degrees, and 28 degrees or -56 degrees, 0 degrees, and 56 degrees in the azimuthal plane), with the target part being presented either at 0 degrees or at one of the right-sided locations. Results showed that spatial separation of 28 degrees was sufficient for a significant improvement in target detection (i.e., in the detection of large interval jumps) compared to the overlap condition, irrespective of the position (frontal or right) of the target part. A larger spatial separation of the parts resulted in further improvements only if the target part was lateralized. These data support the notion of improvement in the suppression of interfering signals with spatial sound source separation. Additionally, the data show that the position of the relevant sound source influences auditory performance.

Methodologies in determining mechanical properties of thin films using nanoindentation

NASA Astrophysics Data System (ADS)

Han, Seung Min Jane

Thin films are critical components of microelectronic and MEMS devices, and evaluating their mechanical properties is of current interest. As the dimensions of the devices become smaller and smaller, however, understanding the mechanical properties of materials at sub-micron length scales becomes more challenging. The conventional methods for evaluating strengths of materials in bulk form cannot be applied, and new methodologies are required for accurately evaluating mechanical properties of thin films. In this work, development of methodologies using the nanoindenter was pursued in three parts: (1) creation of a new method for extracting thin film hardness, (2) use of combinatorial methods for determining compositions with desired mechanical properties, and (3) use of microcompression testing of sub-micron sized pillars to understand plasticity in Al-Sc multilayers. The existing nanoindentation hardness model by Oliver & Pharr is unable to accurately determine the hardness of thin films on substrates with an elastic mismatch. Thus, a new method of analysis for extracting thin film hardness from film/substrate systems, that eliminates the effect of elastic mismatch of the underlying substrate, surface roughness, and also pile-up/sink-in, is needed. Such a method was developed in the first part of this study. The feasibility of using the nanoindentation hardness together with combinatorial methods to efficiently scan through mechanical properties of Ti-Al metallic alloys was examined in the second part of this study. The combinatorial approach provides an efficient method that can be used to determine alloy compositions that might merit further exploration and development as bulk materials. Finally, the mechanical properties of Al-Al3Sc multilayers with bilayer periods ranging from 6-100 nm were examined using microcompression. The sub-micron sized pillars were prepared using the focused ion beam (FIB) and compression tested with the flat tip of the nanoindenter. The measured yield strengths show the trend of increasing strength with decreasing bilayer period, and agree with the nanoindentation hardness results using the suitable Tabor correction factor. Strain softening was observed at large strains, and a new model for the true stress and true strain was developed to account for the inhomogeneous deformation geometry.

X-ray micro-CT measurement of large parts at very low temperature

NASA Astrophysics Data System (ADS)

Koutecký, T.; Zikmund, T.; Glittová, D.; Paloušek, D.; Živčák, J.; Kaiser, J.

2017-03-01

At present, the automotive industry, along with other industries, has increasing demands on accuracy of produced parts and assemblies. Besides the regular dimensional and geometrical inspection, in some cases, also a verification at very low temperatures is required. X-ray computed tomography (CT), as a tool for non-destructive testing, is able to examine samples and then determine dimensions for strictly stable temperature conditions necessary for the stability of the CT system. Until now, no system that allows scanning of samples larger than a few millimeters at temperatures much below 0 °C has been presented. This paper presents a cooling system for CT imaging of parts with length up to 300 mm at the extreme temperature conditions of -40 °C, which are based on automotive industry requests. It describes the equipment and conditions under which it is possible to achieve a temperature stability of samples at low temperatures, while keeping an independent temperature regulation of the CT system. The presented system uses a standard industrial CT device and a newly designed cooling stage with passive cooling based on phase-change material. The system is demonstrated on the measurement of plastic part (car door handle) at temperatures of -40 °C and 20 °C. The paper also presents the method of how to interpret the thermal changes using tools of the commercial software VGStudio MAX (Volume Graphics GmbH, Germany).

U.S. Department of Energy's Regional Carbon Sequestration Partnership Program: Overview

USGS Publications Warehouse

Litynski, J.; Plasynski, S.; Spangler, L.; Finley, R.; Steadman, E.; Ball, D.; Nemeth, K.J.; McPherson, B.; Myer, L.

2009-01-01

The U.S. Department of Energy (DOE) has formed a nationwide network of seven regional partnerships to help determine the best approaches for capturing and permanently storing gases that can contribute to global climate change. The Regional Carbon Sequestration Partnerships (RCSPs) are tasked with determining the most suitable technologies, regulations, and infrastructure for carbon capture, transport, and storage in their areas of the country and parts of Canada. The seven partnerships include more than 350 state agencies, universities, national laboratories, private companies, and environmental organizations, spanning 42 states, two Indian nations, and four Canadian provinces. The Regional Partnerships initiative is being implemented in three phases: ???Characterization Phase (2003-2005): The objective was to collect data on CO2 sources and sinks and develop the human capital to support and enable future carbon sequestration field tests and deployments. The completion of this Phase was marked by release of the Carbon Sequestration Atlas of the United States and Canada-Version 1 which included a common methodology for capacity assessment and reported over 3,000GT of storage capacity in saline formations, depleted oil and gas fields, and coal seams.???Validation Phase (2005-2009): The objective is to plan and implement small-scale (<1??million tons CO2) field testing of storage technologies in areas determined to be favorable for carbon storage. The partnerships are currently conducting over 20 small-scale geologic field tests and 11 terrestrial field tests.???Development Phase (2008-2018): The primary objective is the development of large-scale (>1??million tons of CO2) Carbon Capture and Storage (CCS) projects, which will demonstrate that large volumes of CO2 can be injected safely, permanently, and economically into geologic formations representative of large storage capacity. Even though the RCSP Program is being implemented in three phases, it should be viewed as an integrated whole, with many of the goals and objectives transitioning from one phase to the next. Accomplishments and results from the Characterization Phase have helped to refine goals and activities in the Validation and Deployment Phases. The RCSP Program encourages and requires open information sharing among its members by sponsoring both general workshops and meetings to facilitate information exchange. Although each RCSP has its own objectives and field tests, mutual cooperation has been an important part of the Program thus far. The primary goal of the RCSP initiative is to promote the development of a regional framework and the infrastructure necessary to validate and deploy carbon sequestration technologies within each Partnership's region. ?? 2009 Elsevier Ltd. All rights reserved.

Can Student Teachers Acquire Core Skills for Teaching from Part-Time Employment?

ERIC Educational Resources Information Center

Wylie, Ken; Cummins, Brian

2013-01-01

Part-time employment among university students has become commonplace internationally. Research has largely focused on the impact of part-time employment on academic performance. This research takes an original approach in that it poses the question whether students can acquire core skills relevant to teaching from their part-time employment. The…

Drought Variability in Eastern Part of Romania and its Connection with Large-Scale Air Circulation

NASA Astrophysics Data System (ADS)

Barbu, Nicu; Stefan, Sabina; Georgescu, Florinela

2014-05-01

Drought is a phenomenon that appears due to precipitation deficit and it is intensified by strong winds, high temperatures, low relative humidity and high insolation; in fact, all these factors lead to increasing of evapotranspiration processes that contribute to soil water deficit. The Standardized Precipitation Evapotranspiration Index (SPEI) take into account all this factors listed above. The temporal variability of the drought in Eastern part of Romania for 50 years, during the period 1961-2010, is investigated. This study is focused on the drought variability related to large scale air circulation. The gridded dataset with spatial resolution of 0.5º lat/lon of SPEI, (https://digital.csic.es/handle/10261/72264) were used to analyze drought periods in connection with large scale air circulation determinate from the two catalogues (GWT - GrossWetter-Typen and WLK - WetterLargenKlassifikation) defined in COST733Action. The GWT catalogue uses at input dataset the sea level pressure and the WLK catalogue uses as input dataset the geopotential field at 925 hPa and 500 hPa, wind at 700 hPa and total water content for entire atmospheric column. In this study we use the GWT catalogue with 18 circulation types and the WLK catalogue with 40 circulation types. The analysis for Barlad Hydrological Basin indicated that the negative values (that means water deficit - drought period) of SPEI are associated with prevailing anticyclonic regime and positive values (that means water excess - rainy period) of SPEI are associated with prevailing cyclonic regime as was expected. In last decade was observed an increase of dry period associated with an increase of anticyclonic activity over Romania. Using GWT18 catalogue the drought are associated with the north-eastern anticyclonic circulation type (NE-A). According to the WLK40 catalogue, the dominant circulation type associated with the drought is north-west-anticyclonic-dry anticyclonic (NW-AAD) type. keywords: drought, SPEI, large-scale atmospheric circulation

Analysis of swept-sine runs during modal identification

NASA Astrophysics Data System (ADS)

Gloth, G.; Sinapius, M.

2004-11-01

Experimental modal analysis of large aerospace structures in Europe combine nowadays the benefits of the very reliable but time-consuming phase resonance method and the application of phase separation techniques evaluating frequency response functions (FRF). FRFs of a test structure can be determined by a variety of means. Applied excitation signal waveforms include harmonic signals like stepped-sine excitation, periodic signals like multi-sine excitation, transient signals like impulse and swept-sine excitation, and stochastic signals like random. The current article focuses on slow swept-sine excitation which is a good trade-off between magnitude of excitation level needed for large aircraft and testing time. However, recent ground vibration tests (GVTs) brought up that reliable modal data from swept-sine test runs depend on a proper data processing. The article elucidates the strategy of modal analysis based on swept-sine excitation. The standards for the application of slowly swept sinusoids defined by the international organisation for standardisation in ISO 7626 part 2 are critically reviewed. The theoretical background of swept-sine testing is expounded with particular emphasis to the transition through structural resonances. The effect of different standard procedures of data processing like tracking filter, fast Fourier transform (FFT), and data reduction via averaging are investigated with respect to their influence on the FRFs and modal parameters. Particular emphasis is given to FRF distortions evoked by unsuitable data processing. All data processing methods are investigated on a numerical example. Their practical usefulness is demonstrated on test data taken from a recent GVT on a large aircraft. The revision of ISO 7626 part 2 is suggested regarding the application of slow swept-sine excitation. Recommendations about the proper FRF estimation from slow swept-sine excitation are given in order to enable the optimisation on these applications for future modal survey tests of large aerospace structures.

Dissolved methane in the residual basins of the Aral Sea

NASA Astrophysics Data System (ADS)

Izhitskaya, Elena; Zavialov, Peter; Egorov, Alexander

2017-04-01

The state of the Aral Sea has changed significantly since the second half of the 20th century. Due to the level decline the present-day sea consists of the several water bodies: the Large Aral Sea, the Small Aral Sea and Lake Tshchebas. Water balance peculiarities of each basin caused the differences in physical, chemical and biological structure of the ecosystem. Severe salinization of the Large Aral resulted in the increase of water stratification and formation of the anoxic conditions in the bottom layer. According to the field survey of 2002 [Zavialov et al., 2003; Friedrich, Oberhansli, 2004], hydrogen sulfide was detected in the bottom layer of the Large Aral Sea for the first time. Methane formation is the next reaction after sulfate reduction within process of sequential oxidation of organic matter [Break, 1974]. Thus, methane is an important indicator of biogeochemical processes in natural water environments. Besides due to high greenhouse activity of methane study of its emission to the atmosphere is essential for solution of climatological problems [Bazhin, 2000]. The presented study aims to the evaluation of methane dissolved in waters of the Aral region. Measurements of the gas concentration were carried out on surface and vertical profiles, as well as on point stations in 2012, 2013, 2015 and 2016 years in different parts of the sea. Water samples were analyzed by the head-space method with further gas chromatographic determination of methane concentration [Bolshakov, Egorov, 1987]. According to the obtained data, dissolved methane content in the surface waters of the residual basins of the Aral Sea ranges from 12 to 234 nM/l. One of the main results of the research is detection of intensive methane increase in the lower water layer of the Large Aral to 17014 nM/l in central part and to 147316 nM/l in the Chernyshev Bay.

Changes in neurocranium thickness in early childhood

NASA Astrophysics Data System (ADS)

Gajawelli, Niharika; Deoni, Sean; Shi, Jie; Xu, Liang; Dirks, Holly; Dean, Douglas; O'Muircheartaigh, Jonathan; Sawardekar, Siddhant; Ezis, Andrea; Nelson, Marvin D.; Wang, Yalin; Lepore, Natasha

2015-12-01

Several developmental disorders involve shape abnormalities of the neurocranium, the most common one being craniosynostosis, that affects about 1 in 2000 infants. A key step in determining how these disorders affect neurodevelopment is to establish how the brain and neurocranium co-evolve in the normally developing child. However, due to the scarcity of normally developing infant and pediatric imaging data, there have been a lack of imaging studies pertaining to normal neurocranial development. Here, taking advantage of a large data bank of high quality brain MRI from healthy children ages 0-4 years old, and of a novel conformal geometry-based analysis pipeline, we have been determining a set of statistical atlases of the neurocranium, divided into age groups. In this first part of the study, we focus more specifically on a comparison of 1 and 2 year old infants. Characterizing neurocranium shape changes will enable us to understand how the cranial bones develop in relation to brain development. This in turn will allow a better determination of the effects of neurocranial disorders, which will help inform treatment strategies.

Air motion determination by tracking humidity patterns in isentropic layers

NASA Technical Reports Server (NTRS)

Mancuso, R. L.; Hall, D. J.

1975-01-01

Determining air motions by tracking humidity patterns in isentropic layers was investigated. Upper-air rawinsonde data from the NSSL network and from the AVE-II pilot experiment were used to simulate temperature and humidity profile data that will eventually be available from geosynchronous satellites. Polynomial surfaces that move with time were fitted to the mixing-ratio values of the different isentropic layers. The velocity components of the polynomial surfaces are part of the coefficients that are determined in order to give an optimum fitting of the data. In the mid-troposphere, the derived humidity motions were in good agreement with the winds measured by rawinsondes so long as there were few or no clouds and the lapse rate was relatively stable. In the lower troposphere, the humidity motions were unreliable primarily because of nonadiabatic processes and unstable lapse rates. In the upper troposphere, the humidity amounts were too low to be measured with sufficient accuracy to give reliable results. However, it appears that humidity motions could be used to provide mid-tropospheric wind data over large regions of the globe.

New approaches for automatic threedimensional source localization of acoustic emissions--Applications to concrete specimens.

PubMed

Kurz, Jochen H

2015-12-01

The task of locating a source in space by measuring travel time differences of elastic or electromagnetic waves from the source to several sensors is evident in varying fields. The new concepts of automatic acoustic emission localization presented in this article are based on developments from geodesy and seismology. A detailed description of source location determination in space is given with the focus on acoustic emission data from concrete specimens. Direct and iterative solvers are compared. A concept based on direct solvers from geodesy extended by a statistical approach is described which allows a stable source location determination even for partly erroneous onset times. The developed approach is validated with acoustic emission data from a large specimen leading to travel paths up to 1m and therefore to noisy data with errors in the determined onsets. The adaption of the algorithms from geodesy to the localization procedure of sources of elastic waves offers new possibilities concerning stability, automation and performance of localization results. Fracture processes can be assessed more accurately. Copyright © 2015 Elsevier B.V. All rights reserved.

Measuring UV Curing Parameters of Commercial Photopolymers used in Additive Manufacturing.

PubMed

Bennett, Joe

2017-12-01

A testing methodology was developed to expose photopolymer resins and measure the cured material to determine two key parameters related to the photopolymerization process: E c (critical energy to initiate polymerization) and D p (penetration depth of curing light). Five commercially available resins were evaluated under exposure from 365 nm and 405 nm light at varying power densities and energies. Three different methods for determining the thickness of the cured resin were evaluated. Caliper measurements, stylus profilometry, and confocal laser scanning microscopy showed similar results for hard materials while caliper measurement of a soft, elastomeric material proved inaccurate. Working curves for the five photopolymers showed unique behavior both within and among the resins as a function of curing light wavelength. E c and D p for the five resins showed variations as large as 10×. Variations of this magnitude, if unknown to the user and not controlled for, will clearly affect printed part quality. This points to the need for a standardized approach for determining and disseminating these, and perhaps, other key parameters.

Gait as solution, but what is the problem? Exploring cost, economy and compromise in locomotion.

PubMed

Bertram, John E A

2013-12-01

Many studies have examined how legged mammals move, defining 'what' happens in locomotion. However, few ask 'why' those motions occur as they do. The energetic and functional constraints acting on an animal require that locomotion should be metabolically 'cost effective' and this in large part determines the strategies available to accomplish the task. Understanding the gaits utilised, within the spectrum of gaits possible, and determination of the value of specific relationships among speed, stride length, stride frequency and morphology, depends on identifying the fundamental costs involved and the effects of different movement strategies on those costs. It is argued here that a fundamental loss associated with moving on limbs (centre of mass momentum and energy loss) and two costs involved with controlling and replacing that loss (muscular work of the supporting limb during stance and muscular work of repositioning the limbs during swing) interact to determine the cost trade-offs involved and the optimisation strategies available for each species and speed. These optimisation strategies are what has been observed and characterised as gait. Copyright © 2013 Elsevier Ltd. All rights reserved.

Preliminary location and age database for invertebrate fossils collected in the San Francisco Bay region, California

USGS Publications Warehouse

Parker, John M.; West, William B.; Malmborg, William T.; Brabb, Earl E.

2003-01-01

Most geologic maps published for central California in the past century have been made without the benefit of microfossils. The age of Cretaceous and Tertiary rocks in the structurally complex sedimentary formations of the Coast Ranges is critical in determining stratigraphic succession and in determining whether the juxtapositon of similar appearing formations means that a fault is present. Since the 1930’s, at least, oil company geologists have used microfossils to assist them in geologic mapping and in determining the environments of deposition of sedimentary rocks. This information has been confidential, but in the past 20 years the attitude of petroleum companies about this information has changed, and much material is now available. We report here on approximately 4,700 samples, largely foraminifers, from surface localities in the San Francisco Bay region of California. The information contained here can be used to update geologic maps, to analyze the depth and temperature of ocean water covering parts of California during the Mesozoic and Cenozoic eras, and for solving other geologic problems.

Large geodetic time series constraining the spatial distribution and the time evolution of the velocity field at the western tip of the Aden Ridge in Afar

NASA Astrophysics Data System (ADS)

Doubre, C.; Deprez, A.; Masson, F.; Socquet, A.; Ulrich, P.; Ibrahim Ahmed, S.; de Chabalier, J. B.; Ahmadine Omar, A.; Vigny, C.; Ruegg, J. C.

2014-12-01

We present the results of the last GPS campaign conducted over the Djiboutian part of Eastern Afar. A large and dense geodetic network has been measured regularly since the 90's, and allows an accurate determination of the velocity field associated with the western tip of the Arabia-Somalia divergent plate boundary. Within the Tadjoura Gulf, the Aden ridge consists of a series of 3 en échelon, submerged spreading segments, except for the Asal segment, which is partly above water. The repetition of 6 to 7 measurements together with 6 permanent continuous GNSS stations allow an opportunity to study the spatial distribution of the active extension in relation to these 3 segments, but also to study time variations of the displacements, which are greatly expected to be transitory because of the occurrence of dyking events, small to intermediate seismic events, and volcanic activity. The divergent motion of the two margins of the Gulf occurs at ~15 mm/yr, which is consistent with the long-term estimates of the Arabia-Somalia motion. Across the Asal segment, this value confirms that the effect of the dyking event in 1978 has ended. The velocity gradients show that the deformation is distributed from the southern to the northern rift shoulder. As revealed by the InSAR data however, the along-axis variations of the deformation pattern, i.e. clear superficial active faults in the SE part of the rift and deep opening in the NW part, suggests the remaining influence of the previous dyke intrusions within the segment inner floor. The time series show that the velocity field was more heterogeneous before 2003, when the micro-seismic activity was significant, particularly around the volcanic center. The striking feature of the time evolution of the velocity field consists in the transition from an extension mainly localized across the Asal segment before 2003 to an extension more distributed, implying the influence of the southern Quaternary structures forming the Gaggade and Hanle Basins. This results in a decrease of the opening velocity across the Asal segment. This crucial change suggests that the activity of the volcanic/geothermal centre in the segment is a determining factor in the spatial organization of the deformation, by affecting the activity of the normal faults and thereby favoring the concentration of the extensive deformation.

Mid-infrared InAs/AlGaSb superlattice quantum-cascade lasers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohtani, K.; Fujita, K.; Ohno, H.

2005-11-21

We report on the demonstration of mid-infrared InAs/AlGaSb superlattice quantum-cascade lasers operating at 10 {mu}m. The laser structures are grown on n-InAs (100) substrate by solid-source molecular-beam epitaxy. An InAs/AlGaSb chirped superlattice structure providing a large oscillator strength and fast carrier depopulation is employed as the active part. The observed minimum threshold current density at 80 K is 0.7 kA/cm{sup 2}, and the maximum operation temperature in pulse mode is 270 K. The waveguide loss of an InAs plasmon waveguide is estimated, and the factors that determine the operation temperature are discussed.