DOE Office of Scientific and Technical Information (OSTI.GOV)

Adams, B.W.; et al.

The Large Area Picosecond PhotoDetector (LAPPD) Collaboration was formed in 2009 to develop large-area photodetectors capable of time resolutions measured in pico-seconds, with accompanying sub-millimeter spatial resolution. During the next three and one-half years the Collaboration developed the LAPPD design of 20 x 20 cm modules with gains greater thanmore » $10^7$ and non-uniformity less than $$15\\%$$, time resolution less than 50 psec for single photons and spatial resolution of 700~microns in both lateral dimensions. We describe the R\\&D performed to develop large-area micro-channel plate glass substrates, resistive and secondary-emitting coatings, large-area bialkali photocathodes, and RF-capable hermetic packaging. In addition, the Collaboration developed the necessary electronics for large systems capable of precise timing, built up from a custom low-power 15-GigaSample/sec waveform sampling 6-channel integrated circuit and supported by a two-level modular data acquisition system based on Field-Programmable Gate Arrays for local control, data-sparcification, and triggering. We discuss the formation, organization, and technical successes and short-comings of the Collaboration. The Collaboration ended in December 2012 with a transition from R\\&D to commercialization.« less

Use of remote sensing for land use policy formulation. [Allegan, Bay, Branch, Ionia, Livingston, and St. Clair Counties in Michigan and Lake Michigan shorelines

NASA Technical Reports Server (NTRS)

Boylan, M. (Principal Investigator)

1978-01-01

The author has identified the following significant results. By utilizing remote sensing techniques, it was possible to accurately inventory a relatively large area for sand mining impact on protection and management of shoreland dunes within a limited time period and at a relatively low cost. Analysis of two sample areas selected from the Grand Mere area after prohibition of off-road-vehicle use indicated an increase in vegetation regrowth of 8.52% for sample area 1 and of 4.44% for sample area 2.

Designing a sampling system for concurrently measuring outdoor recreation visitation and describing visitor characteristics

Treesearch

Donald B.K. English; Stanley J. Zarnoch; Susan M. Kocis

2004-01-01

Two primary information needs for managing recreation areas and the visitors to those areas are: (1) good estimates of visitation volume, and (2) accurate descriptions of visitor characteristics, such as length of stay, frequency of visit, and primary activity. For National Forests in the United States of America with large undeveloped areas, efficient sampling for the...

Best Practices in Using Large, Complex Samples: The Importance of Using Appropriate Weights and Design Effect Compensation

ERIC Educational Resources Information Center

Osborne, Jason W.

2011-01-01

Large surveys often use probability sampling in order to obtain representative samples, and these data sets are valuable tools for researchers in all areas of science. Yet many researchers are not formally prepared to appropriately utilize these resources. Indeed, users of one popular dataset were generally found "not" to have modeled…

Field size, length, and width distributions based on LACIE ground truth data. [large area crop inventory experiment

NASA Technical Reports Server (NTRS)

Pitts, D. E.; Badhwar, G.

1980-01-01

The development of agricultural remote sensing systems requires knowledge of agricultural field size distributions so that the sensors, sampling frames, image interpretation schemes, registration systems, and classification systems can be properly designed. Malila et al. (1976) studied the field size distribution for wheat and all other crops in two Kansas LACIE (Large Area Crop Inventory Experiment) intensive test sites using ground observations of the crops and measurements of their field areas based on current year rectified aerial photomaps. The field area and size distributions reported in the present investigation are derived from a representative subset of a stratified random sample of LACIE sample segments. In contrast to previous work, the obtained results indicate that most field-size distributions are not log-normally distributed. The most common field size observed in this study was 10 acres for most crops studied.

Bedload Rating and Flow Competence Curves Vary With Watershed and Bed Material Parameters

NASA Astrophysics Data System (ADS)

Bunte, K.; Abt, S. R.

2003-12-01

Bedload transport rating curves and flow competence curves (largest bedload size for specified flow) are usually not known for streams unless a large number of bedload samples has been collected and analyzed. However, this information is necessary for assessing instream flow needs and stream responses to watershed effects. This study therefore analyzed whether bedload transport rating and flow competence curves were related to stream parameters. Bedload transport rating curves and flow competence curves were obtained from extensive bedload sampling in six gravel- and cobble-bed mountain streams. Samples were collected using bedload traps and a large net sampler, both of which provide steep and relatively well-defined bedload rating and flow competence curves due to a long sampling duration, a large sampler opening and a large sampler capacity. The sampled streams have snowmelt regimes, steep (1-9%) gradients, and watersheds that are mainly forested and relatively undisturbed with basin area sizes of 8 to 105 km2. The channels are slightly incised and can contain flows of more than 1.5 times bankfull with little overbank flow. Exponents of bedload rating and flow competence curves obtained from these measurements were found to systematically increase with basin area size and decrease with the degree of channel armoring. By contrast, coefficients of bedload rating and flow competence curves decreased with basin size and increased with armoring. All of these relationships were well-defined (0.86 < r2 < 0.99). Data sets from other studies in coarse-bedded streams fit the indicated trend if the sampling device used allows measuring bedload transport rates over a wide range and if bedload supply is somewhat low. The existence of a general positive trend between bedload rating curve exponents and basin area, and a negative trend between coefficients and basin area, is confirmed by a large data set of bedload rating curves obtained from Helley-Smith samples. However, in this case, the trends only become visible as basin area sizes span a wide range (1 - 10,000 km2). The well-defined relationships obtained from the bedload trap and the large net sampler suggest that exponents and coefficients of bedload transport rating curves (and flow competence curves) are predictable from an easily obtainable parameter such as basin size. However, the relationships of bedload rating curve exponents and coefficients with basin size and armoring appear to be influenced by the sampling device used and the watershed sediment production.

Heat transfer from an oxidized large copper surface to liquid helium: Dependence on surface orientation and treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iwamoto, A.; Mito, T.; Takahata, K.

Heat transfer of large copper plates (18 x 76 mm) in liquid helium has been measured as a function of orientation and treatment of the heat transfer surface. The results relate to applications of large scale superconductors. In order to clarify the influence of the area where the surface treatment peels off, the authors studied five types of heat transfer surface areas including: (a) 100% polished copper sample, (b) and (c) two 50% oxidized copper samples having different patterns of oxidation, (d) 75% oxidized copper sample, (e) 90% oxidized copper sample, and (f) 100% oxidized copper sample. They observed thatmore » the critical heat flux depends on the heat transfer surface orientation. The critical heat flux is a maximum at angles of 0{degrees} - 30{degrees} and decreases monotonically with increasing angles above 30{degrees}, where the angle is taken in reference to the horizontal axis. On the other hand, the minimum heat flux is less dependent on the surface orientation. More than 75% oxidation on the surface makes the critical heat flux increase. The minimum heat fluxes of the 50 and 90% oxidized Cu samples approximately agree with that of the 100% oxidized Cu sample. Experiments and calculations show that the critical and the minimum heat fluxes are a bilinear function of the fraction of oxidized surface area.« less

Comparison of different biopsy forceps models for tissue sampling in eosinophilic esophagitis.

PubMed

Bussmann, Christian; Schoepfer, Alain M; Safroneeva, Ekaterina; Haas, Nadine; Godat, Sébastien; Sempoux, Christine; Simon, Hans-Uwe; Straumann, Alex

2016-12-01

Background and aims: Eosinophilic esophagitis (EoE) is a mixed inflammatory and fibrostenotic disease. Unlike superficial inflammatory changes, subepithelial fibrosis is not routinely sampled in esophageal biopsies. This study aimed to evaluate the efficacy and safety of deep esophageal sampling with four different types of biopsy forceps. Patients and methods: In this cross-sectional study, esophageal biopsies were taken in 30 adult patients by one expert endoscopist. Biopsies sampled from distal esophagus using a static jaw forceps (Olympus, FB-11K-1) were compared with proximal biopsies sampled with static jaw (Olympus, FB-45Q-1), alligator jaw (Olympus, FB-210K), and large-capacity forceps (Boston Scientific, Radial Jaw 4). One pathologist calculated the surface area of epithelial and subepithelial layers in hematoxylin and eosin (H&E)-stained biopsies. Results: Subepithelial tissue was acquired in 97 % (static jaw FB-11K-1), 93 % (static jaw FB-45Q-1), 80 % (alligator jaw), and 55 % (large-capacity) of samples. Median (interquartile [IQR]) ratios of surface area of epithelial to subepithelial tissue were: static jaw FB-45Q-1, 1.07 (0.65 - 4.465); static jaw FB-11K-1, 1.184 (0.608 - 2.545); alligator jaw, 2.353 (1.312 - 4.465); and large-capacity, 2.71 (1.611 - 4.858). The static jaw models obtained a larger surface area of subepithelial tissue compared with the alligator jaw ( P  < 0.001 and P  = 0.037, for FB-11K-1 and FB-45Q-1, respectively) and the large-capacity forceps ( P  < 0.001, for both static jaw models). No esophageal perforations occurred. Conclusions: The static jaw forceps models allowed sampling of subepithelial tissue in > 90 % of biopsies and appear to be superior to alligator or large-capacity forceps in sampling larger amounts of subepithelial tissue. © Georg Thieme Verlag KG Stuttgart · New York.

Evaluation of area strain response of dielectric elastomer actuator using image processing technique

NASA Astrophysics Data System (ADS)

Sahu, Raj K.; Sudarshan, Koyya; Patra, Karali; Bhaumik, Shovan

2014-03-01

Dielectric elastomer actuator (DEA) is a kind of soft actuators that can produce significantly large electric-field induced actuation strain and may be a basic unit of artificial muscles and robotic elements. Understanding strain development on a pre-stretched sample at different regimes of electrical field is essential for potential applications. In this paper, we report about ongoing work on determination of area strain using digital camera and image processing technique. The setup, developed in house consists of low cost digital camera, data acquisition and image processing algorithm. Samples have been prepared by biaxially stretched acrylic tape and supported between two cardboard frames. Carbon-grease has been pasted on the both sides of the sample, which will be compliant with electric field induced large deformation. Images have been grabbed before and after the application of high voltage. From incremental image area, strain has been calculated as a function of applied voltage on a pre-stretched dielectric elastomer (DE) sample. Area strain has been plotted with the applied voltage for different pre-stretched samples. Our study shows that the area strain exhibits nonlinear relationship with applied voltage. For same voltage higher area strain has been generated on a sample having higher pre-stretched value. Also our characterization matches well with previously published results which have been done with costly video extensometer. The study may be helpful for the designers to fabricate the biaxial pre-stretched planar actuator from similar kind of materials.

Thermoelectic properties of CVD grown large area graphene

NASA Astrophysics Data System (ADS)

Sherehiy, Andriy

This thesis is based on experimental work on thermoelectric properties of CVD grown large area graphene. The thermoelectric power (TEP) of CVD (Chemical Vapor Deposition) grown large area graphene transferred onto a Si/SiO 2_substrate was measured by simply attaching two miniature thermocouples and a resistive heater. Availability of such large area graphene facilitates straight forward TEP measurement without the use of any microfabrication processes. All investigated graphene samples showed a positive TEP S ≈ 20 mVK in ambient conditions and saturated at a negative value as low as S ≈ -50 mVK after vacuum-annealing at 500 K in a vacuum of 10-7 Torr. The observed p-type behavior under ambient conditions is attributed to the oxygen doping, while the n-type behavior under degassed conditions is due to electron doping from SiO2 surface states. It was observed that the sign of the TEP switched from negative to positive for the degassed graphene when exposed to acceptor gases. Conversely, the TEP of vacuum-annealed graphene exposed to the donor gases became even more negative than the TEP of vacuum-annealed sample.

LACIE large area acreage estimation. [United States of America

NASA Technical Reports Server (NTRS)

Chhikara, R. S.; Feiveson, A. H. (Principal Investigator)

1979-01-01

A sample wheat acreage for a large area is obtained by multiplying its small grains acreage estimate as computed by the classification and mensuration subsystem by the best available ratio of wheat to small grains acreages obtained from historical data. In the United States, as in other countries with detailed historical data, an additional level of aggregation was required because sample allocation was made at the substratum level. The essential features of the estimation procedure for LACIE countries are included along with procedures for estimating wheat acreage in the United States.

Interferometric scanning optical microscope for surface characterization.

PubMed

Offside, M J; Somekh, M G

1992-11-01

A phase-sensitive scanning optical microscope is described that can measure surface height changes down to 0.1 nm. This is achieved by using two heterodyne Michelson interferometers in parallel. One interferometer probes the sample with a tightly focused beam, and the second has a collimated beam that illuminates a large area of the surface, providing a large area on sample reference. This is facilitated by using a specially constructed objective lens that permits the relative areas illuminated by the two probe beams to be varied both arbitrarily and independently, thus ensuring an accurate absolute phase measurement. We subtracted the phase outputs from each interferometer to provide the sample phase information, canceling the phase noise resulting from microphonics in the process. Results from a prototype version of the microscope are presented that demonstrate the advantages of the system over existing techniques.

Sampling large geographic areas for rare species using environmental DNA: A study of bull trout Salvelinus confluentus occupancy in western Montana

Treesearch

Kevin McKelvey; Michael Young; W. L. Knotek; K. J. Carim; T. M. Wilcox; T. M. Padgett-Stewart; Michael Schwartz

2016-01-01

This study tested the efficacy of environmental DNA (eDNA) sampling to delineate the distribution of bull trout Salvelinus confluentus in headwater streams in western Montana, U.S.A. Surveys proved fast, reliable and sensitive: 124 samples were collected across five basins by a single crew in c. 8days. Results were largely consistent with past electrofishing,...

Summary of surface-water-quality data collected for the Northern Rockies Intermontane Basins National Water-Quality Assessment Program in the Clark Fork-Pend Oreille and Spokane River basins, Montana, Idaho, and Washington, water years 1999-2001

USGS Publications Warehouse

Beckwith, Michael A.

2003-01-01

Water-quality samples were collected at 10 sites in the Clark Fork-Pend Oreille and Spokane River Basins in water years 1999 – 2001 as part of the Northern Rockies Intermontane Basins (NROK) National Water-Quality Assessment (NAWQA) Program. Sampling sites were located in varied environments ranging from small streams and rivers in forested, mountainous headwater areas to large rivers draining diverse landscapes. Two sampling sites were located immediately downstream from the large lakes; five sites were located downstream from large-scale historical mining and oreprocessing areas, which are now the two largest “Superfund” (environmental remediation) sites in the Nation. Samples were collected during a wide range of streamflow conditions, more frequently during increasing and high streamflow and less frequently during receding and base-flow conditions. Sample analyses emphasized major ions, nutrients, and selected trace elements. Streamflow during the study ranged from more than 130 percent of the long-term average in 1999 at some sites to 40 percent of the long-term average in 2001. River and stream water in the study area exhibited small values for specific conductance, hardness, alkalinity, and dissolved solids. Dissolved oxygen concentrations in almost all samples were near saturation. Median total nitrogen and total phosphorus concentrations in samples from most sites were smaller than median concentrations reported for many national programs and other NAWQA Program study areas. The only exceptions were two sites downstream from large wastewater-treatment facilities, where median concentrations of total nitrogen exceeded the national median. Maximum concentrations of total phosphorus in samples from six sites exceeded the 0.1 milligram per liter threshold recommended for limiting nuisance aquatic growth. Concentrations of arsenic, cadmium, copper, lead, mercury, and zinc were largest in samples from sites downstream from historical mining and ore-processing areas in the upper Clark Fork in Montana and the South Fork Coeur d’Alene River in Idaho. Concentrations of dissolved lead in all 32 samples from the South Fork Coeur d’Alene River exceeded the Idaho chronic criterion for the protection of aquatic life at the median hardness level measured during the study. Concentrations of dissolved zinc in all samples collected at this site exceeded both the chronic and acute criteria at all hardness levels measured. When all data from all NROK sites were combined, median concentrations of dissolved arsenic, dissolved and total recoverable copper, total recoverable lead, and total recoverable zinc in the NROK study area appeared to be similar to or slightly smaller than median concentrations at sites in other NAWQA Program study areas in the Western United States affected by historical mining activities. Although the NROK median total recoverable lead concentration was the smallest among the three Western study areas compared, concentrations in several NROK samples were an order of magnitude larger than the maximum concentrations measured in the Upper Colorado River and Great Salt Lake Basins. Dissolved cadmium, dissolved lead, and total recoverable zinc concentrations at NROK sites were more variable than in the other study areas; concentrations ranged over almost three orders of magnitude between minimum and maximum values; the range of dissolved zinc concentrations in the NROK study area exceeded three orders of magnitude.

Large area optical mapping of surface contact angle.

PubMed

Dutra, Guilherme; Canning, John; Padden, Whayne; Martelli, Cicero; Dligatch, Svetlana

2017-09-04

Top-down contact angle measurements have been validated and confirmed to be as good if not more reliable than side-based measurements. A range of samples, including industrially relevant materials for roofing and printing, has been compared. Using the top-down approach, mapping in both 1-D and 2-D has been demonstrated. The method was applied to study the change in contact angle as a function of change in silver (Ag) nanoparticle size controlled by thermal evaporation. Large area mapping reveals good uniformity for commercial Aspen paper coated with black laser printer ink. A demonstration of the forensic and chemical analysis potential in 2-D is shown by uncovering the hidden CsF initials made with mineral oil on the coated Aspen paper. The method promises to revolutionize nanoscale characterization and industrial monitoring as well as chemical analyses by allowing rapid contact angle measurements over large areas or large numbers of samples in ways and times that have not been possible before.

Evaluation of Sampling Methods for Bacillus Spore ...

EPA Pesticide Factsheets

Journal Article Following a wide area release of biological materials, mapping the extent of contamination is essential for orderly response and decontamination operations. HVAC filters process large volumes of air and therefore collect highly representative particulate samples in buildings. HVAC filter extraction may have great utility in rapidly estimating the extent of building contamination following a large-scale incident. However, until now, no studies have been conducted comparing the two most appropriate sampling approaches for HVAC filter materials: direct extraction and vacuum-based sampling.

RECONNAISSANCE FOR URANIUM IN ASPHALT-BEARING ROCKS IN THE WESTERN UNITED STATES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hail, W.J. Jr.

1957-01-01

An appraisal of asphait-bearing rocks as potential sources of uranium was made during 1953 and 1954 in 45 areas in Calif., Utah, Wyo., Mont., N. Mex., Tex., Okla., and Mo. A total of 202 samples from these areas was analyzed for uranium. The oldest rocks sampled are Ordovician in age, and the youngest are Recent. Although none of the deposits are of value at this time as a source of U, some of the deposits may constitute a low-grade U resource, but recovery of the U will depend upon the primary use of the asphalt. Significant amounts of U lnmore » the ash of oil extracted from these rocks were found in samples from 7 of the 45 areas examined. These areas are Chalome Creek, McKittrick, Edna, and Los Alamos Calif.; Vernal, Utah; Sulphur, Okla.; and Ellis, Mo. The average U content in the ash of the extracted oil of samples from these 7 areas ranges from 0.028 to 0.376%. All except the Chalone Creek area contain large estimated reserves of asphalt-bearing rock, ranging from 15 million to almost 2 billion tons. The average U content of samples from 13 additiomal areas ranges from 0.020 to 0.06B% in the ash of the extracted oil. Many of these areas contain very large reserves of asphalt-bearing rocks. It is believed that most of the asphalt deposits are oil residues, and that the U was introduced during or after the late stages of oil movement and loss of the lighter oil fractions. (auth)« less

A non-destructive method for quantifying small-diameter woody biomass in southern pine forests

Treesearch

D. Andrew Scott; Rick Stagg; Morris Smith

2006-01-01

Quantifying the impact of silvicultural treatments on woody understory vegetation largely has been accomplished by destructive sampling or through estimates of frequency and coverage. In studies where repeated measures of understory biomass across large areas are needed, destructive sampling and percent cover estimates are not satisfactory. For example, estimates of...

Biological tissue imaging with a position and time sensitive pixelated detector.

PubMed

Jungmann, Julia H; Smith, Donald F; MacAleese, Luke; Klinkert, Ivo; Visser, Jan; Heeren, Ron M A

2012-10-01

We demonstrate the capabilities of a highly parallel, active pixel detector for large-area, mass spectrometric imaging of biological tissue sections. A bare Timepix assembly (512 × 512 pixels) is combined with chevron microchannel plates on an ion microscope matrix-assisted laser desorption time-of-flight mass spectrometer (MALDI TOF-MS). The detector assembly registers position- and time-resolved images of multiple m/z species in every measurement frame. We prove the applicability of the detection system to biomolecular mass spectrometry imaging on biologically relevant samples by mass-resolved images from Timepix measurements of a peptide-grid benchmark sample and mouse testis tissue slices. Mass-spectral and localization information of analytes at physiologic concentrations are measured in MALDI-TOF-MS imaging experiments. We show a high spatial resolution (pixel size down to 740 × 740 nm(2) on the sample surface) and a spatial resolving power of 6 μm with a microscope mode laser field of view of 100-335 μm. Automated, large-area imaging is demonstrated and the Timepix' potential for fast, large-area image acquisition is highlighted.

Intraoperative optical coherence tomography of the cerebral cortex using a 7 degree-of freedom robotic arm

NASA Astrophysics Data System (ADS)

Reyes Perez, Robnier; Jivraj, Jamil; Yang, Victor X. D.

2017-02-01

Optical Coherence Tomography (OCT) provides a high-resolution imaging technique with limited depth penetration. The current use of OCT is limited to relatively small areas of tissue for anatomical structure diagnosis or minimally invasive guided surgery. In this study, we propose to image a large area of the surface of the cerebral cortex. This experiment aims to evaluate the potential difficulties encountered when applying OCT imaging to large and irregular surface areas. The current state-of-the-art OCT imaging technology uses scanning systems with at most 3 degrees-of-freedom (DOF) to obtain a 3D image representation of the sample tissue. We propose the use of a 7 DOF industrial robotic arm to increase the scanning capabilities of our OCT. Such system will be capable of acquiring data from large samples of tissue that are too irregular for conventional methods. Advantages and disadvantages of our system are discussed.

Investigation to develop a multistage forest sampling inventory system using ERTS-1 imagery

NASA Technical Reports Server (NTRS)

Langley, P. G.; Vanroessel, J. W. (Principal Investigator); Wert, S. L.

1975-01-01

The author has identified the following significant results. The annotation system produced a RMSE of about 200 m ground distance in the MSS data system with the control data used. All the analytical MSS interpretation models tried were highly significant. However, the gains in forest sampling efficiency that can be achieved by using the models vary from zero to over 50 percent depending on the area to which they are applied and the sampling method used. Among the sampling methods tried, regression sampling yielded substantial and the most consistent gains. The single most significant variable in the interpretation model was the difference between bands 5 and 7. The contrast variable, computed by the Hadamard transform was significant but did not contribute much to the interpretation model. Forest areas containing very large timber volumes because of large tree sizes were not separable from areas of similar crown cover but containing smaller trees using ERTS image interpretation only. All correlations between space derived timber volume predictions and estimates obtained from aerial and ground sampling were relatively low but significant and stable. There was a much stronger relationship between variables derived from MSS and U2 data than between U2 and ground data.

Influence of the type of oxidant on anion exchange properties of fibrous Cladophora cellulose/polypyrrole composites.

PubMed

Razaq, Aamir; Mihranyan, Albert; Welch, Ken; Nyholm, Leif; Strømme, Maria

2009-01-15

The electrochemically controlled anion absorption properties of a novel large surface area composite paper material composed of polypyrrole (PPy) and cellulose derived from Cladophora sp. algae, synthesized with two oxidizing agents, iron(III) chloride and phosphomolybdic acid (PMo), were analyzed in four different electrolytes containing anions (i.e., chloride, aspartate, glutamate, and p-toluenesulfonate) of varying size.The composites were characterized with scanning and transmission electron microscopy, N2 gas adsorption,and conductivity measurements. The potential-controlled ion exchange properties of the materials were studied by cyclic voltammetry and chronoamperometry at varying potentials. The surface area and conductivity of the iron(III) chloride synthesized sample were 58.8 m2/g and 0.65 S/cm, respectively, while the corresponding values for the PMo synthesized sample were 31.3 m2/g and 0.12 S/cm. The number of absorbed ions per sample mass was found to be larger for the iron(III) chloride synthesized sample than for the PMo synthesized one in all four electrolytes. Although the largest extraction yields were obtained in the presence of the smallest anion (i.e., chloride) for both samples, the relative degree of extraction for the largest ions (i.e., glutamate and p-toluenesulfonate) was higher for the PMo sample. This clearly shows that it is possible to increase the extraction yield of large anions by carrying out the PPy polymerization in the presence of large anions. The results likewise show that high ion exchange capacities, as well as extraction and desorption rates, can be obtained for large anions with high surface area composites coated with relatively thin layers of PPy.

Evaluation of three gears for sampling spawning populations of rainbow trout in a large Alaskan river

USGS Publications Warehouse

Schwanke, C.J.; Hubert, W.A.

2004-01-01

Alternatives to electrofishing are needed for sampling sexually mature rainbow trout Oncorhynchus mykiss during the spawning season in large Alaskan rivers. We compared hook and line, beach seining, and actively fished gill nets as sampling tools. Beach seining and active gill netting yielded similar catch rates, length frequencies, and sex ratios of sexually mature fish. Hook-and-line sampling was less effective, with a lower catch rate and selectivity for immature fish and sexually mature females. We conclude that both beach seining and active gill netting can serve as alternatives to electrofishing for sampling sexually mature rainbow trout stocks during the spawning season in large rivers with stable spring flows and spawning areas with few snags.

Crop identification and area estimation over large geographic areas using LANDSAT MSS data

NASA Technical Reports Server (NTRS)

Bauer, M. E. (Principal Investigator)

1977-01-01

The author has identified the following significant results. LANDSAT MSS data was adequate to accurately identify wheat in Kansas; corn and soybean estimates in Indiana were less accurate. Computer-aided analysis techniques were effectively used to extract crop identification information from LANDSAT data. Systematic sampling of entire counties made possible by computer classification methods resulted in very precise area estimates at county, district, and state levels. Training statistics were successfully extended from one county to other counties having similar crops and soils if the training areas sampled the total variation of the area to be classified.

Sampling benthic macroinvertebrates in a large flood-plain river: Considerations of study design, sample size, and cost

USGS Publications Warehouse

Bartsch, L.A.; Richardson, W.B.; Naimo, T.J.

1998-01-01

Estimation of benthic macroinvertebrate populations over large spatial scales is difficult due to the high variability in abundance and the cost of sample processing and taxonomic analysis. To determine a cost-effective, statistically powerful sample design, we conducted an exploratory study of the spatial variation of benthic macroinvertebrates in a 37 km reach of the Upper Mississippi River. We sampled benthos at 36 sites within each of two strata, contiguous backwater and channel border. Three standard ponar (525 cm(2)) grab samples were obtained at each site ('Original Design'). Analysis of variance and sampling cost of strata-wide estimates for abundance of Oligochaeta, Chironomidae, and total invertebrates showed that only one ponar sample per site ('Reduced Design') yielded essentially the same abundance estimates as the Original Design, while reducing the overall cost by 63%. A posteriori statistical power analysis (alpha = 0.05, beta = 0.20) on the Reduced Design estimated that at least 18 sites per stratum were needed to detect differences in mean abundance between contiguous backwater and channel border areas for Oligochaeta, Chironomidae, and total invertebrates. Statistical power was nearly identical for the three taxonomic groups. The abundances of several taxa of concern (e.g., Hexagenia mayflies and Musculium fingernail clams) were too spatially variable to estimate power with our method. Resampling simulations indicated that to achieve adequate sampling precision for Oligochaeta, at least 36 sample sites per stratum would be required, whereas a sampling precision of 0.2 would not be attained with any sample size for Hexagenia in channel border areas, or Chironomidae and Musculium in both strata given the variance structure of the original samples. Community-wide diversity indices (Brillouin and 1-Simpsons) increased as sample area per site increased. The backwater area had higher diversity than the channel border area. The number of sampling sites required to sample benthic macroinvertebrates during our sampling period depended on the study objective and ranged from 18 to more than 40 sites per stratum. No single sampling regime would efficiently and adequately sample all components of the macroinvertebrate community.

Stable Isotopic Constraints on the Geographic Sources of Marijuana in Alaska

NASA Astrophysics Data System (ADS)

Booth, A. L.; Wooller, M. J.; Haubenstock, N. A.; Howe, T. A.

2007-12-01

Marijuana in Alaska can have numerous sources. Confiscated plants are known to originate either from within the state (e.g., Fairbanks and the Matanuska-Susitna Valley) or from numerous areas outside the state (e.g., Latin America, Canada and the contiguous United States). Latin America reportedly supplies a large percentage of the marijuana currently distributed in the lower 48 states of the U.S.A. However, in more remote areas of the country such as Fairbanks, Alaska, the supply proportions from different geographic areas are not well known. This is due to an insufficient ability to trace source regions from which confiscated marijuana was originally grown. As such, we have analyzed multiple stable isotopes (C, N, O and H) preserved in marijuana samples to identify the likely geographic source from which the marijuana originated (Drug Enforcement Agency license # RW0324551). These samples were confiscated in Fairbanks, Alaska and supplied to us by the University of Alaska Fairbanks (UAF) Police Department. Among 36 marijuana plant samples, we found an unexpectedly large range in the stable carbon isotope compositions (‰13C = -62.2‰ to -24.4‰), with twelve of the 36 samples exhibiting exceedingly low δ13C (-36.1‰ to -62.2‰) relative to typical δ13C of other C3 plants. Interior growing conditions (e.g., hydroponics and/or greenhouses) and a variety of CO2 sources (e.g., CO2 from tanks and fermentation CO2 generators) frequently supplied to growing marijuana to improve yields may account for these exceptionally low δ13C values. Stable oxygen and hydrogen isotope compositions (δ18O and δD vs. V-SMOW) of the marijuana samples were found to range from 10.0‰ to 27.6‰ and -197.1‰ to -134.9‰ respectively. The large range of values suggests that the samples originated from multiple sources ranging from low to high latitudes. δ15N of the marijuana samples also exhibited a large range (-7.0‰ to 14.8‰). This project has implications for the improvement of forensic technology in relatively remote areas such as Alaska. Officers for the Alaska Bureau of Drug and Alcohol Enforcement spend a significant amount of time controlling the production and distribution of marijuana, while the resources allocated for law enforcement must be utilized over a wide geographic area.

Area estimation using multiyear designs and partial crop identification

NASA Technical Reports Server (NTRS)

Sielken, R. L., Jr.

1984-01-01

Statistical procedures were developed for large area assessments using both satellite and conventional data. Crop acreages, other ground cover indices, and measures of change were the principal characteristics of interest. These characteristics are capable of being estimated from samples collected possibly from several sources at varying times, with different levels of identification. Multiyear analysis techniques were extended to include partially identified samples; the best current year sampling design corresponding to a given sampling history was determined; weights reflecting the precision or confidence in each observation were identified and utilized, and the variation in estimates incorporating partially identified samples were quantified.

The brightest galaxies in the first 700 Myr: Building Hubble's legacy of large area IR imaging for JWST and beyond

NASA Astrophysics Data System (ADS)

Trenti, Michele

2017-08-01

Hubble's WFC3 has been a game changer for the study of early galaxy formation in the first 700 Myr after the Big Bang. Reliable samples of sources to redshift z 11, which can be discovered only from space, are now constraining the evolution of the galaxy luminosity function into the epoch of reionization. Unexpectedly but excitingly, the recent spectroscopic confirmations of L>L* galaxies at z>8.5 demonstrate that objects brighter than our own Galaxy are already present 500 Myr after the Big Bang, creating a challenge to current theoretical/numerical models that struggle to explain how galaxies can grow so luminous so quickly. Yet, the existing HST observations do not cover sufficient area, nor sample a large enough diversity of environments to provide an unbiased sample of sources, especially at z 9-11 where only a handful of bright candidates are known. To double this currently insufficient sample size, to constrain effectively the bright-end of the galaxy luminosity function at z 9-10, and to provide targets for follow-up imaging and spectroscopy with JWST, we propose a large-area pure-parallel survey that will discover the Brightest of Reionizing Galaxies (BoRG[4JWST]). We will observe 580 arcmin^2 over 125 sightlines in five WFC3 bands (0.35 to 1.7 micron) using high-quality pure-parallel opportunities available in the cycle (3 orbits or longer). These public observations will identify more than 80 intrinsically bright galaxies at z 8-11, investigate the connection between halo mass, star formation and feedback in progenitors of groups and clusters, and build HST lasting legacy of large-area, near-IR imaging.

PYRAMID ROADLESS AREA, CALIFORNIA.

USGS Publications Warehouse

Armstrong, Augustus K.; Scott, Douglas F.

1984-01-01

A geologic and mineral survey was conducted in the Pyramid Roadless Area, California. The area contains mineral showings, but no mineral-resource potential was identified during our studies. Three granodiorite samples on the west side of the roadless area contained weakly anomalous concentrations of uranium. Two samples of roof-pendant rocks, one metasedimentary rock and one metavolcanic rock, contain low concentrations of copper, and of copper and molybdenum, respectively. Although none was identified, the geologic terrane is permissive for mineral occurrences and large-scale, detailed geologic mapping of the areas of metasedimentary and metavolcanic roof pendants in the Pyramid Roadless Area could define a mineral-resource potential for tungsten and precious metals.

A PRIOR EVALUATION OF TWO-STAGE CLUSTER SAMPLING FOR ACCURACY ASSESSMENT OF LARGE-AREA LAND-COVER MAPS

EPA Science Inventory

Two-stage cluster sampling reduces the cost of collecting accuracy assessment reference data by constraining sample elements to fall within a limited number of geographic domains (clusters). However, because classification error is typically positively spatially correlated, withi...

Species-area relationships and extinction forecasts.

PubMed

Halley, John M; Sgardeli, Vasiliki; Monokrousos, Nikolaos

2013-05-01

The species-area relationship (SAR) predicts that smaller areas contain fewer species. This is the basis of the SAR method that has been used to forecast large numbers of species committed to extinction every year due to deforestation. The method has a number of issues that must be handled with care to avoid error. These include the functional form of the SAR, the choice of equation parameters, the sampling procedure used, extinction debt, and forest regeneration. Concerns about the accuracy of the SAR technique often cite errors not much larger than the natural scatter of the SAR itself. Such errors do not undermine the credibility of forecasts predicting large numbers of extinctions, although they may be a serious obstacle in other SAR applications. Very large errors can arise from misinterpretation of extinction debt, inappropriate functional form, and ignoring forest regeneration. Major challenges remain to understand better the relationship between sampling protocol and the functional form of SARs and the dynamics of relaxation, especially in continental areas, and to widen the testing of extinction forecasts. © 2013 New York Academy of Sciences.

Comparison of sampling designs for estimating deforestation from landsat TM and MODIS imagery: a case study in Mato Grosso, Brazil.

PubMed

Zhu, Shanyou; Zhang, Hailong; Liu, Ronggao; Cao, Yun; Zhang, Guixin

2014-01-01

Sampling designs are commonly used to estimate deforestation over large areas, but comparisons between different sampling strategies are required. Using PRODES deforestation data as a reference, deforestation in the state of Mato Grosso in Brazil from 2005 to 2006 is evaluated using Landsat imagery and a nearly synchronous MODIS dataset. The MODIS-derived deforestation is used to assist in sampling and extrapolation. Three sampling designs are compared according to the estimated deforestation of the entire study area based on simple extrapolation and linear regression models. The results show that stratified sampling for strata construction and sample allocation using the MODIS-derived deforestation hotspots provided more precise estimations than simple random and systematic sampling. Moreover, the relationship between the MODIS-derived and TM-derived deforestation provides a precise estimate of the total deforestation area as well as the distribution of deforestation in each block.

Comparison of Sampling Designs for Estimating Deforestation from Landsat TM and MODIS Imagery: A Case Study in Mato Grosso, Brazil

PubMed Central

Zhu, Shanyou; Zhang, Hailong; Liu, Ronggao; Cao, Yun; Zhang, Guixin

2014-01-01

Sampling designs are commonly used to estimate deforestation over large areas, but comparisons between different sampling strategies are required. Using PRODES deforestation data as a reference, deforestation in the state of Mato Grosso in Brazil from 2005 to 2006 is evaluated using Landsat imagery and a nearly synchronous MODIS dataset. The MODIS-derived deforestation is used to assist in sampling and extrapolation. Three sampling designs are compared according to the estimated deforestation of the entire study area based on simple extrapolation and linear regression models. The results show that stratified sampling for strata construction and sample allocation using the MODIS-derived deforestation hotspots provided more precise estimations than simple random and systematic sampling. Moreover, the relationship between the MODIS-derived and TM-derived deforestation provides a precise estimate of the total deforestation area as well as the distribution of deforestation in each block. PMID:25258742

Measurement of radon concentration in some water samples belonging to some adjoining areas of Pathankot, Punjab

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Ajay, E-mail: ajay782@rediffmail.com; Sharma, Sumit, E-mail: sumitshrm210@gmail.com

The study of radon concentration was measured in some areas of Pathankot district, Punjab, India, from the health hazard point of view due to radon. The exposure to radon through drinking water is largely by inhalation and ingestion. RAD 7, an electronic solid state silicon detector (Durridgeco., USA) was used to measure the radon concentration in drinking water samples of the study area. The recorded values of radon concentration in these water samples are below the recommended limit by UNSCEAR and European commission. The recommended limit of radon concentration in water samples is 4 to 40 Bq/l given by UNSCEARmore » [1] and European commission has recommended the safe limit for radon concentration in water sample is 100 Bq/l [2].« less

Measurement of radon concentration in some water samples belonging to some adjoining areas of Pathankot, Punjab

NASA Astrophysics Data System (ADS)

Kumar, Ajay; Sharma, Sumit

2015-08-01

The study of radon concentration was measured in some areas of Pathankot district, Punjab, India, from the health hazard point of view due to radon. The exposure to radon through drinking water is largely by inhalation and ingestion. RAD 7, an electronic solid state silicon detector (Durridgeco., USA) was used to measure the radon concentration in drinking water samples of the study area. The recorded values of radon concentration in these water samples are below the recommended limit by UNSCEAR and European commission. The recommended limit of radon concentration in water samples is 4 to 40 Bq/l given by UNSCEAR [1] and European commission has recommended the safe limit for radon concentration in water sample is 100 Bq/l [2].

An assessment of Lot Quality Assurance Sampling to evaluate malaria outcome indicators: extending malaria indicator surveys.

PubMed

Biedron, Caitlin; Pagano, Marcello; Hedt, Bethany L; Kilian, Albert; Ratcliffe, Amy; Mabunda, Samuel; Valadez, Joseph J

2010-02-01

Large investments and increased global prioritization of malaria prevention and treatment have resulted in greater emphasis on programme monitoring and evaluation (M&E) in many countries. Many countries currently use large multistage cluster sample surveys to monitor malaria outcome indicators on a regional and national level. However, these surveys often mask local-level variability important to programme management. Lot Quality Assurance Sampling (LQAS) has played a valuable role for local-level programme M&E. If incorporated into these larger surveys, it would provide a comprehensive M&E plan at little, if any, extra cost. The Mozambique Ministry of Health conducted a Malaria Indicator Survey (MIS) in June and July 2007. We applied LQAS classification rules to the 345 sampled enumeration areas to demonstrate identifying high- and low-performing areas with respect to two malaria program indicators-'household possession of any bednet' and 'household possession of any insecticide-treated bednet (ITN)'. As shown by the MIS, no province in Mozambique achieved the 70% coverage target for household possession of bednets or ITNs. By applying LQAS classification rules to the data, we identify 266 of the 345 enumeration areas as having bednet coverage severely below the 70% target. An additional 73 were identified with low ITN coverage. This article demonstrates the feasibility of integrating LQAS into multistage cluster sampling surveys and using these results to support a comprehensive national, regional and local programme M&E system. Furthermore, in the recommendations we outlined how to integrate the Large Country-LQAS design into macro-surveys while still obtaining results available through current sampling practices.

Thermoelectric properties of CVD grown large area graphene

NASA Astrophysics Data System (ADS)

Sherehiy, Andriy; Jayasinghe, Ruwantha; Stallard, Robert; Sumanasekera, Gamini; Sidorov, Anton; Benjamin, Daniel; Jiang, Zhigang; Yu, Qingkai; Wu, Wei; Bao, Jiming; Liu, Zhihong; Pei, Steven; Chen, Yong

2010-03-01

The thermoelectric power (TEP) of CVD (Chemical Vapor Deposition) grown large area graphene transferred onto a Si/SiO2 substrate was measured by simply attaching two miniature thermocouples and a resistive heater. Availability of such large area graphene facilitates straight forward TEP measurement without the use of any microfabrication processes. All investigated graphene samples showed a positive TEP ˜ + 30 μV/K in ambient conditions and saturated at a negative value as low as ˜ -75 μV/K after vacuum-annealing at 500 K in a vacuum of ˜10-7 Torr. The observed p-type behavior under ambient conditions is attributed to the oxygen doping, while the n-type behavior under degassed conditions is due to electron doping from SiO2 surface states. It was observed that the sign of the TEP switched from negative to positive for the degassed graphene when exposed to acceptor gases. Conversely, the TEP of vacuum-annealed graphene exposed to the donor gases became even more negative than the TEP of vacuum-annealed sample.

Geochemical survey of the Blood Mountain Roadless Area, Union and Lumpkin counties, Georgia

USGS Publications Warehouse

Koeppen, Robert P.; Nelson, Arthur E.

1989-01-01

The U.S. Geological Survey (USGS) made a reconnaissance geochemical survey of the Blood Mountain Roadless Area to search for unexposed mineral deposits which might be recognized by a geochemical signature in the abundance of distribution patterns of trace elements. Forty five fine-grained stream-sediment samples and 45 panned-concentrate samples were collected in the Blood Mountain study area (fig. 1). A.E. Nelson, in conjunction with detailed geologic mapping, collected 13 rock-chip samples for geochemical analysis, in addition to a large number of hand specimins for thin-section study. Nelson's geologic study (1983), combined with this geochemical survey, provide the basis for our mineral-resource assessment of the Blood Mountain Roadless Area (Koeppen and others, 1983).

Cooperative geochemical investigation of geothermal resources in the Imperial Valley and Yuma areas. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coplen, T.B.

1973-10-01

Preliminary studies indicate that the Imperial Valley has a large geothermal potential. In order to delineate additional geothermal systems a chemical and isotopic investigation of samples from water wells, springs, and geothermal wells in the Imperial Valley and Yuma areas was conducted. Na, K, and Ca concentrations of nearly 200 well water, spring water, hot spring, and geothermal fluid samples from the Imperial Valley area were measured by atomic absorption spectrophotometry. Fournier and Truesdell's function was determined for each water sample. Suspected geothermal areas are identified. Hydrogen and oxygen isotope abundances were determined in order to determine and to identifymore » the source of the water in the Mesa geothermal system. (JGB)« less

High-energy x-ray diffraction from surfaces and nanoparticles

NASA Astrophysics Data System (ADS)

Hejral, U.; Müller, P.; Shipilin, M.; Gustafson, J.; Franz, D.; Shayduk, R.; Rütt, U.; Zhang, C.; Merte, L. R.; Lundgren, E.; Vonk, V.; Stierle, A.

2017-11-01

High-energy surface-sensitive x-ray diffraction (HESXRD) is a powerful high-energy photon technique (E > 70 keV) that has in recent years proven to allow a fast data acquisition for the 3D structure determination of surfaces and nanoparticles under in situ and operando conditions. The use of a large-area detector facilitates the direct collection of nearly distortion-free diffraction patterns over a wide q range, including crystal truncation rods perpendicular to the surface and large-area reciprocal space maps from epitaxial nanoparticles, which is not possible in the conventional low-photon energy approach (E =10 -20 keV ). Here, we present a comprehensive mathematical approach, explaining the working principle of HESXRD for both single-crystal surfaces and epitaxial nanostructures on single-crystal supports. The angular calculations used in conventional crystal truncation rod measurements at low-photon energies are adopted for the high-photon-energy regime, illustrating why and to which extent large reciprocal-space areas can be probed in stationary geometry with fixed sample rotation. We discuss how imperfections such as mosaicity and finite domain size aid in sampling a substantial part of reciprocal space without the need of rotating the sample. An exact account is given of the area probed in reciprocal space using such a stationary mode, which is essential for in situ or operando time-resolved experiments on surfaces and nanostructures.

WE-E-18A-01: Large Area Avalanche Amorphous Selenium Sensors for Low Dose X-Ray Imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheuermann, J; Goldan, A; Zhao, W

2014-06-15

Purpose: A large area indirect flat panel imager (FPI) with avalanche gain is being developed to achieve x-ray quantum noise limited low dose imaging. It uses a thin optical sensing layer of amorphous selenium (a-Se), known as High-Gain Avalanche Rushing Photoconductor (HARP), to detect optical photons generated from a high resolution x-ray scintillator. We will report initial results in the fabrication of a solid-state HARP structure suitable for a large area FPI. Our objective is to establish the blocking layer structures and defect suppression mechanisms that provide stable and uniform avalanche gain. Methods: Samples were fabricated as follows: (1) ITOmore » signal electrode. (2) Electron blocking layer. (3) A 15 micron layer of intrinsic a-Se. (4) Transparent hole blocking layer. (5) Multiple semitransparent bias electrodes to investigate avalanche gain uniformity over a large area. The sample was exposed to 50ps optical excitation pulses through the bias electrode. Transient time of flight (TOF) and integrated charge was measured. A charge transport simulation was developed to investigate the effects of varying blocking layer charge carrier mobility on defect suppression, avalanche gain and temporal performance. Results: Avalanche gain of ∼200 was achieved experimentally with our multi-layer HARP samples. Simulations using the experimental sensor structure produced the same magnitude of gain as a function of electric field. The simulation predicted that the high dark current at a point defect can be reduced by two orders of magnitude by blocking layer optimization which can prevent irreversible damage while normal operation remained unaffected. Conclusion: We presented the first solid state HARP structure directly scalable to a large area FPI. We have shown reproducible and uniform avalanche gain of 200. By reducing mobility of the blocking layers we can suppress defects and maintain stable avalanche. Future work will optimize the blocking layers to prevent lag and ghosting.« less

Bee honey as an environmental bioindicator of pesticides' occurrence in six agricultural areas of Greece.

PubMed

Balayiannis, George; Balayiannis, Panos

2008-10-01

The pollution of six agricultural areas of Greece (north, central, south) by insecticides used in crop protection has been investigated utilizing, as a bioindicator, bee honey produced in those areas. Honey samples collected randomly from apiaries located in those areas were analyzed for pesticide residues with a multianalytical method, able to determine simultaneously up to 10 organophosphorous insecticides from the same honey extract. Findings concerning the acaricide coumaphos were also included, even though it is not used in crop protection. Coumaphos is used to control the mite Varroa destructor, an external parasite of the honeybee. The above areas are cultivated in large extent with citrus trees or cotton or sunflower crops, which are good forages for honeybees. The main pests of those crops are insects; hence, insecticides are used on a large scale for crop protection. The most contaminated samples originated from citrus groves; 16 out of 19 had pesticide residues: 4 samples had chlorfenvinphos (21.05%), 10 had chlorpyrifos (52.63%) and 2 had phorate (10.53%). Out of 17 samples from cotton fields, residues were found in 8, phorate in 6 (35.29%), chlorfenvinphos in 1 (5.88%), and chlorpyrifos in 1 (5.88%). Out of nine samples from fields of sunflower, four had phorate residues (44.44%). In brief, from the 50 analyzed samples, residues of chlorfenvinphos were detected in 5 samples (10%), residues of chlorpyrifos in 11 samples (22%), and residues of phorate in 12 samples (24%). Their levels ranged between 0.70 and 0.89 microg/kg. Coumaphos residues ranged from 0.10 up to 4.80 microg/kg and were derived exclusively from beehives treated with Perizin (the commercial formulation of coumaphos) for Varroa control. This study indicates that in agricultural areas with developed apiculture, useful information about the occurrence and the distribution of pesticide residues due to crop protection treatments can be derived from the analysis of randomly collected honey samples, used as bioindicators. It also shows that, very often, the chemicals used by apiculturists inside the hives in order to control disease are the main pollutants of the produced honey.

A priori evaluation of two-stage cluster sampling for accuracy assessment of large-area land-cover maps

USGS Publications Warehouse

Wickham, J.D.; Stehman, S.V.; Smith, J.H.; Wade, T.G.; Yang, L.

2004-01-01

Two-stage cluster sampling reduces the cost of collecting accuracy assessment reference data by constraining sample elements to fall within a limited number of geographic domains (clusters). However, because classification error is typically positively spatially correlated, within-cluster correlation may reduce the precision of the accuracy estimates. The detailed population information to quantify a priori the effect of within-cluster correlation on precision is typically unavailable. Consequently, a convenient, practical approach to evaluate the likely performance of a two-stage cluster sample is needed. We describe such an a priori evaluation protocol focusing on the spatial distribution of the sample by land-cover class across different cluster sizes and costs of different sampling options, including options not imposing clustering. This protocol also assesses the two-stage design's adequacy for estimating the precision of accuracy estimates for rare land-cover classes. We illustrate the approach using two large-area, regional accuracy assessments from the National Land-Cover Data (NLCD), and describe how the a priorievaluation was used as a decision-making tool when implementing the NLCD design.

Validation of Rapid Radiochemical Method for Californium ...

EPA Pesticide Factsheets

Technical Brief In the event of a radiological/nuclear contamination event, the response community would need tools and methodologies to rapidly assess the nature and the extent of contamination. To characterize a radiologically contaminated outdoor area and to inform risk assessment, large numbers of environmental samples would be collected and analyzed over a short period of time. To address the challenge of quickly providing analytical results to the field, the U.S. EPA developed a robust analytical method. This method allows response officials to characterize contaminated areas and to assess the effectiveness of remediation efforts, both rapidly and accurately, in the intermediate and late phases of environmental cleanup. Improvement in sample processing and analysis leads to increased laboratory capacity to handle the analysis of a large number of samples following the intentional or unintentional release of a radiological/nuclear contaminant.

Sorption of N2 and EGME vapors on some soils, clays, and mineral oxides and determination of sample surface areas by use of sorption data

USGS Publications Warehouse

Chiou, C.T.; Rutherford, D.W.; Manes, M.

1993-01-01

Vapor sorption isotherms of ethylene glycol monoethyl ether (EGME) at room temperature and isotherms of N2 gas at liquid nitrogen temperature were determined for various soils and minerals. The N2 monolayer capacities [Qm (N2)] were calculated from the BET equation and used to determine the surface areas. To examine whether EGME is an appropriate adsorbate for determination of surface areas, the apparent EGME monolayer capacities [Qm (EGME)ap] were also obtained by use of the BET equation. For sand, aluminum oxide, kaolinite, hematite, and synthetic hydrous iron oxide, which are relatively free of organic impurity and expanding/solvating minerals, the Qm (EGME)ap values are in good conformity with the corresponding Qm (N2) values and would give surface areas consistent with BET (N2) values. For other samples (Woodburn soil, a natural hydrous iron oxide, illite, and montmorillonite), the Qm (EGME)ap values overestimate the Qm (N2) values from a moderate to a large extent, depending on the sample. A high-organic-content peat shows a very small BET (N2) surface area; the EGME/ peat isotherm is linear and does not yield a calculation of the surface area. Large discrepancies between results of the two methods for some samples are attributed to the high solubility of polar EGME in soil organic matter and/ or to the cation solvation of EGME with solvating clays. The agreement for other samples is illustrative of the consistency of the BET method when different adsorbates are used, so long as they do not exhibit bulk penetration and/or cation solvation. ?? 1993 American Chemical Society.

Satellite versus ground-based estimates of burned area: A comparison between MODIS based burned area and fire agency reports over North America in 2007

Treesearch

Stephane Mangeon; Robert Field; Michael Fromm; Charles McHugh; Apostolos Voulgarakis

2015-01-01

North American wildfire management teams routinely assess burned area on site during firefighting campaigns; meanwhile, satellite observations provide systematic and global burned-area data. Here we compare satellite and ground-based daily burned area for wildfire events for selected large fires across North America in 2007 on daily timescales. In a sample of 26 fires...

Topography of acute stroke in a sample of 439 right brain damaged patients.

PubMed

Sperber, Christoph; Karnath, Hans-Otto

2016-01-01

Knowledge of the typical lesion topography and volumetry is important for clinical stroke diagnosis as well as for anatomo-behavioral lesion mapping analyses. Here we used modern lesion analysis techniques to examine the naturally occurring lesion patterns caused by ischemic and by hemorrhagic infarcts in a large, representative acute stroke patient sample. Acute MR and CT imaging of 439 consecutively admitted right-hemispheric stroke patients from a well-defined catchment area suffering from ischemia (n = 367) or hemorrhage (n = 72) were normalized and mapped in reference to stereotaxic anatomical atlases. For ischemic infarcts, highest frequencies of stroke were observed in the insula, putamen, operculum and superior temporal cortex, as well as the inferior and superior occipito-frontal fascicles, superior longitudinal fascicle, uncinate fascicle, and the acoustic radiation. The maximum overlay of hemorrhages was located more posteriorly and more medially, involving posterior areas of the insula, Heschl's gyrus, and putamen. Lesion size was largest in frontal and anterior areas and lowest in subcortical and posterior areas. The large and unbiased sample of stroke patients used in the present study accumulated the different sub-patterns to identify the global topographic and volumetric pattern of right hemisphere stroke in humans.

Effects of land use on quality of water in stratified-drift aquifers in Connecticut

USGS Publications Warehouse

Grady, Stephen J.

1994-01-01

Human activities associated with agricultural, residential, commercial, and industrial land uses have affected the quality of water in the four stratified-drift aquifers examined in Connecticut. A study to evaluate quantitatively the effects of human activities, expressed as land use, on regional ground-water quality was initiated in 1984 as part of the U.S. Geological Survey's Toxic Waste-round-Water Contamination Program. Water-quality data were collected from 116 shallow stainless-steel wells installed beneath or immediately downgradient from seven types of land use areas within the Pootatuck, Pomperaug, Farmington, and Hockanum River valleys in Connecticut. Analysis of variance on the ranked concentrations of 21 largely uncensored or slightly censored constituents, and contingency-table analysis of the frequency of detection of 49 moderately to highly censored constituents indicate that 27 water-quality variables differ at the 0.05 level of significance for samples from at least one land use area. For most constituents, concentrations or detection frequencies are lowest in samples from the undeveloped areas, which characterize background water-quality conditions. The effect of agricultural land use on groundwater quality reflects tillage practices; tilled areas affect the water quality to a greater degree than do untilled areas. Twenty percent of the wells in the tilled agricultural areas yielded water with concentrations of nitrate plus nitrite-nitrogen exceeding 10 milligrams per liter. Atrazine detections in one-third of the wells in areas of tilled agricultural land use were significantly more common than in the undeveloped areas. Ground-water quality beneath sewered residential areas is more severely affected by inorganic and organic nonpoint-source contaminants than is water quality beneath unsewered residential areas. Median concentrations or detection frequencies of most physical properties and inorganic constituents of ground water are higher in sewered than in unsewered residential areas. Generally low concentrations (less than 1.0 microgram per liter) of one or more of 17 volatile organic compounds were detected in samples from 62 percent of the wells in the unsewered residential areas. Most of these compounds were detected in less than 10 percent of the ground-water samples from the unsewered residential areas, however, and consequently, their frequency of detections was not significantly different than in samples from other land use areas. The detection of chloroform in ground-water samples from 47 percent of the wells in the sewered residential areas is significantly higher than the frequency of detection of chloroform in samples from the undeveloped, tilled agricultural, and unsewered residential areas. The quality of ground water is adversely affected beneath commercial areas more so than beneath all other land use areas. Median concentrations of sodium (22.5 milligrams per liter), chloride (36 milligrams per liter), and dissolved solids (286 milligrams per liter) are highest in ground-water samples in commercial areas. Detections of tetrachloroethylene, trichloroethylene, and 1,2-transdichloroethylene were significantly more common in ground-water samples from the commercial areas than in samples from one or more of the other land use areas. Tetrachloroethylene was detected in water samples from 50 percent of the observation wells in the commercial areas at concentrations of up to 1,300 micrograms per liter. Trichloroethylene and 1,2-transdichloroethylene were found at concentrations of up to 20 and 55 micrograms per liter, respectively, in samples from more than 40 percent of the wells in the commercial areas. Although industrial areas occupy only a small part of each of the study areas, they have a disproportionately large effect on ground-water quality. One or more of 12 volatile organic compounds were detected in water samples from 91 percent of the observation wells in the industrial areas

An assessment of Lot Quality Assurance Sampling to evaluate malaria outcome indicators: extending malaria indicator surveys

PubMed Central

Biedron, Caitlin; Pagano, Marcello; Hedt, Bethany L; Kilian, Albert; Ratcliffe, Amy; Mabunda, Samuel; Valadez, Joseph J

2010-01-01

Background Large investments and increased global prioritization of malaria prevention and treatment have resulted in greater emphasis on programme monitoring and evaluation (M&E) in many countries. Many countries currently use large multistage cluster sample surveys to monitor malaria outcome indicators on a regional and national level. However, these surveys often mask local-level variability important to programme management. Lot Quality Assurance Sampling (LQAS) has played a valuable role for local-level programme M&E. If incorporated into these larger surveys, it would provide a comprehensive M&E plan at little, if any, extra cost. Methods The Mozambique Ministry of Health conducted a Malaria Indicator Survey (MIS) in June and July 2007. We applied LQAS classification rules to the 345 sampled enumeration areas to demonstrate identifying high- and low-performing areas with respect to two malaria program indicators—‘household possession of any bednet’ and ‘household possession of any insecticide-treated bednet (ITN)’. Results As shown by the MIS, no province in Mozambique achieved the 70% coverage target for household possession of bednets or ITNs. By applying LQAS classification rules to the data, we identify 266 of the 345 enumeration areas as having bednet coverage severely below the 70% target. An additional 73 were identified with low ITN coverage. Conclusions This article demonstrates the feasibility of integrating LQAS into multistage cluster sampling surveys and using these results to support a comprehensive national, regional and local programme M&E system. Furthermore, in the recommendations we outlined how to integrate the Large Country-LQAS design into macro-surveys while still obtaining results available through current sampling practices. PMID:20139435

Large tree diameter distribution modelling using sparse airborne laser scanning data in a subtropical forest in Nepal

NASA Astrophysics Data System (ADS)

Rana, Parvez; Vauhkonen, Jari; Junttila, Virpi; Hou, Zhengyang; Gautam, Basanta; Cawkwell, Fiona; Tokola, Timo

2017-12-01

Large-diameter trees (taking DBH > 30 cm to define large trees) dominate the dynamics, function and structure of a forest ecosystem. The aim here was to employ sparse airborne laser scanning (ALS) data with a mean point density of 0.8 m-2 and the non-parametric k-most similar neighbour (k-MSN) to predict tree diameter at breast height (DBH) distributions in a subtropical forest in southern Nepal. The specific objectives were: (1) to evaluate the accuracy of the large-tree fraction of the diameter distribution; and (2) to assess the effect of the number of training areas (sample size, n) on the accuracy of the predicted tree diameter distribution. Comparison of the predicted distributions with empirical ones indicated that the large tree diameter distribution can be derived in a mixed species forest with a RMSE% of 66% and a bias% of -1.33%. It was also feasible to downsize the sample size without losing the interpretability capacity of the model. For large-diameter trees, even a reduction of half of the training plots (n = 250), giving a marginal increase in the RMSE% (1.12-1.97%) was reported compared with the original training plots (n = 500). To be consistent with these outcomes, the sample areas should capture the entire range of spatial and feature variability in order to reduce the occurrence of error.

Protocol for Detection of Yersinia pestis in Environmental ...

EPA Pesticide Factsheets

Methods Report This is the first ever open-access and detailed protocol available to all government departments and agencies, and their contractors to detect Yersinia pestis, the pathogen that causes plague, from multiple environmental sample types including water. Each analytical method includes sample processing procedure for each sample type in a step-by-step manner. It includes real-time PCR, traditional microbiological culture, and the Rapid Viability PCR (RV-PCR) analytical methods. For large volume water samples it also includes an ultra-filtration-based sample concentration procedure. Because of such a non-restrictive availability of this protocol to all government departments and agencies, and their contractors, the nation will now have increased laboratory capacity to analyze large number of samples during a wide-area plague incident.

Geochemical survey of the Chattahoochee Roadless Area, Towns, Union, and White counties, Georgia

USGS Publications Warehouse

Koeppen, Robert P.; Nelson, Arthur E.

1989-01-01

Th U.S. Geological Survey made a reconnaissance geochemical survey of the Chattahoochee Roadless Area (fig. 1) to search for unexposed mineral deposits which might be recognized by a geochemical signature in the abundance or distribution patterns of trace elements. As part of a regional geochemical reconnaissance, M/ Hurst (University of Georgia) collected 51 fine-grained stream-sediment samples and 45 planned-concentrate samples  of alluvial gravels in the Chattahoochee study area (see figure 1). A.E. Nelson, in conjunction with detailed geologic mapping (Nelso, 1983), collected 10 rock-chip samples for geochemical analysis in addition to a large number of hand specimens for thin-section study. In order to evaluate isolated anomalies indicated by the earlier sampling, R.P. Koeppen, D.M. Sutphin, and P.D. Schruben collected several additional panned-concentrate, stream-sediment, and rock samples from the area in 1986. Both the geologic study by Nelson (1983) and this geochemical survey provide the basis for our mineral-resource assessment of the Chattahoochee Roadless Area (Nelson and others, 1983). 

Patterns of oribatid mite species diversity: testing the effects of elevation, area and sampling effort.

PubMed

Mumladze, Levan; Murvanidze, Maka; Maraun, Mark

2017-07-01

Elevational gradients in species diversity and species area relationships are two well established patterns that are not mutually exclusive in space and time. Elevation and area are both considered as good proxies to detect and characterize the patterns of species diversity distribution. However, such studies are hampered by the incomplete biodiversity data available for ecologists, which may affect the pattern perceptions. Using the large dataset of oribatid mite communities sampled in Georgia, we tested the effects of altitude and area on species distribution using various approaches, while explicitly considering the biases from sampling effort. Our results showed that elevation and area are strongly correlated (with increasing absolute elevation, land area decreases) and both have strong linear effects on species diversity distribution when studied separately. Approaches based on multiple regression and direct removal of co-varied factors, indicated that the effect of area can actually override the effect of elevation in describing the oribatid species diversity distribution along with elevation. On the other hand, the bias of sampling proved significant in perception of elevational species richness pattern with less effect on elevational species area relationship. We suggest that the sampling alone may be responsible for patterns observed and thus should be considered in ecological studies when eligible.

Mapping large extensions of flat dentin through digital microscopy: introduction to the method and possible applications.

PubMed

Reis, Claudia; De-Deus, Gustavo; Marins, Juliana; Fidel, Sandra; Fidel, Rivail; Paciornik, Sidnei

2012-08-01

To introduce a mapping method to characterize large dentin surfaces using digital microscopy and to discuss the advantages and possible applications of the method. Twenty unerupted third molars were sectioned transversally exposing coronal dentin surfaces. The microscopic mosaic method was used to generate a large field image with the resolution necessary to measure characteristics of dentin tubules. The AxioVision 4.7 software was used to control a motorized optical microscope and the process of acquiring approximately 400 small images to generate each dentin mosaic. An image analysis routine measured the number of tubules (NT) and the ratio between the total area of tubules and the area of the mosaic - the area fraction (AF) - of each mosaic. An automatic procedure transformed the mosaic image into a color map, providing a direct visual representation of tubule density through colors. The dentin maps were used for a comparative qualitative analysis of tubule density distribution of each sample. The results for NT (92450 to 196029 tubules/sample) and AF (4.12% to 11.10%) demonstrated a wide variation among dentin samples. The maps confirmed the microstructure variety, also revealing strong local variations in tubule density within each sample. The mapping method was able to perform dentin morphology characterization and is a valuable tool for producing a baseline for dentin adhesion studies. The method could be also useful in determining the real contribution of dentin structures to the final adhesion quality.

Occurrence of Veterinary Antibiotics in Swine Manure from Large-scale Feedlots in Zhejiang Province, China.

PubMed

Wang, Hua; Chu, Yixuan; Fang, Chengran

2017-04-01

The occurrence and distribution of five sulfonamides and three tetracyclines in swine manure sampled from large-scale feedlots in different areas of Zhejiang Province, China were detected using solid-phase extraction and high-performance liquid chromatography. All eight test antibiotics were detected in most of the manure samples. The dominant antibiotics in swine manure were sulfadiazine, sulfamerazine, sulfadimidine, tetracycline, and chlortetracycline. The maximum concentration of residual antibiotic reached up to 57.95 mg/kg (chlortetracycline). The concentrations and distribution of both types of antibiotics in swine manure of different areas varied greatly. Relatively higher concentrations of sulfonamides were found in swine manure from the Zhejiang area in this experiment compared with previous studies. The results revealed that antibiotics were extensively used in feedlots in this district and that animal manure might act as a non-specific source of antibiotic residues in farmlands and aquatic environments.

Large area multi-channel plasmonic absorber based on the touching triangular dimers fabricated by angle controlled colloidal nanolithography

NASA Astrophysics Data System (ADS)

Hamidi, S. M.; Behjati, S.

2018-02-01

Here we introduce large area plasmonic touching triangular dimers by angle controlled colloidal nanolithography to use them as an efficient multi channel absorber and also high figure of merit sensors. For this purpose, we coated gold thin films onto nanometric and also micrometric polystyrene hexagonal closed packed masks in different deposition angles and also diverse substrate polar angles. Our prepared samples, after remove masks, show large area touching triangular pattern with different inter particle distances in greater polar angles. To get more sense about optical response of the samples such as transmittance and also electric field distribution, we use finite difference time domain method in simulation part. The transmittance plot shows one narrow or multi-channel adjustable deep depend on inter-particle distances which can be controlled by azimuthally angle in nano lithography process. Also, due to the isoelliptical points in the transmittance spectra; we can see the bright and dark plasmon modes coupling and thus the Fano like resonance takes place in the optical spectral region which is very useful for refractive index measurement.

Polycyclic aromatic hydrocarbons in caribou, moose, and wolf scat samples from three areas of the Alberta oil sands.

PubMed

Lundin, Jessica I; Riffell, Jeffrey A; Wasser, Samuel K

2015-11-01

Impacts of toxic substances from oil production in the Alberta oil sands (AOS), such as polycyclic aromatic hydrocarbons (PAHs), have been widely debated. Studies have been largely restricted to exposures from surface mining in aquatic species. We measured PAHs in Woodland caribou (Rangifer tarandus caribou), moose (Alces americanus), and Grey wolf (Canis lupus) across three areas that varied in magnitude of in situ oil production. Our results suggest a distinction of PAH level and source profile (petro/pyrogenic) between study areas and species. Caribou samples indicated pyrogenic sourced PAHs in the study area previously devastated by forest fire. Moose and wolf samples from the high oil production area demonstrated PAH ratios indicative of a petrogenic source and increased PAHs, respectively. These findings emphasize the importance of broadening monitoring and research programs in the AOS. Copyright © 2015 Elsevier Ltd. All rights reserved.

A RESEARCH PLAN FOR THE USE OF THERMAL AVHRR IMAGERY TO STUDY ANNUAL AND SEASONAL MEAN SURFACE TEMPERATURES FOR LARGE LAKES IN NORTH AMERICA

EPA Science Inventory

Surface and vertical temperature data will be obtained from several large lakes With surface areas large enough to be effectively sampled with AVHRR imagery. Yearly and seasonal patterns of surface and whole water column thermal values will be compared to estimates of surface tem...

Group extraction of organic compounds present in liquid samples

NASA Technical Reports Server (NTRS)

Jahnsen, Vilhelm J. (Inventor)

1976-01-01

An extraction device is disclosed comprising a tube containing a substantially inert, chemically non-reactive packing material with a large surface area to volume ratio. A sample which consists of organic compounds dissolved in a liquid, is introduced into the tube. As the sample passes through the packing material it spreads over the material's large surface area to form a thin liquid film which is held on the packing material in a stationary state. A particular group or family of compounds is extractable from the sample by passing a particular solvent system consisting of a solvent and selected reagents through the packing material. The reagents cause optimum conditions to exist for the compounds of the particular family to pass through the phase boundary between the sample liquid and the solvent of the solvent system. Thus, the compounds of the particular family are separated from the sample liquid and become dissolved in the solvent of the solvent system. The particular family of compounds dissolved in the solvent, representing an extract, exits the tube together with the solvent through the tube's nozzle, while the rest of the sample remains on the packing material in a stationary state. Subsequently, a different solvent system may be passed through the packing material to extract another family of compounds from the remaining sample on the packing material.

Geochemical characteristics of rare earth elements in different types of soil: A chemometric approach.

PubMed

Khan, Aysha Masood; Behkami, Shima; Yusoff, Ismail; Md Zain, Sharifuddin Bin; Bakar, Nor Kartini Abu; Bakar, Ahmad Farid Abu; Alias, Yatimah

2017-10-01

Rare earth elements (REEs) are becoming significant due to their huge applications in many industries, large-scale mining and refining activities. Increasing usage of such metals pose negative environmental impacts. In this research ICP-MS has been used to analyze soil samples collected from former ex-mining areas in the depths of 0-20 cm, 21-40 cm, and 41-60 cm of residential, mining, natural, and industrial areas of Perak. Principal component analysis (PCA) revealed that soil samples taken from different mining, industrial, residential, and natural areas are separated into four clusters. It was observed that REEs were abundant in most of the samples from mining areas. Concentration of the rare elements decrease in general as we move from surface soil to deeper soils. Copyright © 2017 Elsevier Ltd. All rights reserved.

Intermediate Pond Sizes Contain the Highest Density, Richness, and Diversity of Pond-Breeding Amphibians

PubMed Central

Semlitsch, Raymond D.; Peterman, William E.; Anderson, Thomas L.; Drake, Dana L.; Ousterhout, Brittany H.

2015-01-01

We present data on amphibian density, species richness, and diversity from a 7140-ha area consisting of 200 ponds in the Midwestern U.S. that represents most of the possible lentic aquatic breeding habitats common in this region. Our study includes all possible breeding sites with natural and anthropogenic disturbance processes that can be missing from studies where sampling intensity is low, sample area is small, or partial disturbance gradients are sampled. We tested whether pond area was a significant predictor of density, species richness, and diversity of amphibians and if values peaked at intermediate pond areas. We found that in all cases a quadratic model fit our data significantly better than a linear model. Because small ponds have a high probability of pond drying and large ponds have a high probability of fish colonization and accumulation of invertebrate predators, drying and predation may be two mechanisms driving the peak of density and diversity towards intermediate values of pond size. We also found that not all intermediate sized ponds produced many larvae; in fact, some had low amphibian density, richness, and diversity. Further analyses of the subset of ponds represented in the peak of the area distribution showed that fish, hydroperiod, invertebrate density, and canopy are additional factors that drive density, richness and diversity of ponds up or down, when extremely small or large ponds are eliminated. Our results indicate that fishless ponds at intermediate sizes are more diverse, produce more larvae, and have greater potential to recruit juveniles into adult populations of most species sampled. Further, hylid and chorus frogs are found predictably more often in ephemeral ponds whereas bullfrogs, green frogs, and cricket frogs are found most often in permanent ponds with fish. Our data increase understanding of what factors structure and maintain amphibian diversity across large landscapes. PMID:25906355

Image analysis of representative food structures: application of the bootstrap method.

PubMed

Ramírez, Cristian; Germain, Juan C; Aguilera, José M

2009-08-01

Images (for example, photomicrographs) are routinely used as qualitative evidence of the microstructure of foods. In quantitative image analysis it is important to estimate the area (or volume) to be sampled, the field of view, and the resolution. The bootstrap method is proposed to estimate the size of the sampling area as a function of the coefficient of variation (CV(Bn)) and standard error (SE(Bn)) of the bootstrap taking sub-areas of different sizes. The bootstrap method was applied to simulated and real structures (apple tissue). For simulated structures, 10 computer-generated images were constructed containing 225 black circles (elements) and different coefficient of variation (CV(image)). For apple tissue, 8 images of apple tissue containing cellular cavities with different CV(image) were analyzed. Results confirmed that for simulated and real structures, increasing the size of the sampling area decreased the CV(Bn) and SE(Bn). Furthermore, there was a linear relationship between the CV(image) and CV(Bn) (.) For example, to obtain a CV(Bn) = 0.10 in an image with CV(image) = 0.60, a sampling area of 400 x 400 pixels (11% of whole image) was required, whereas if CV(image) = 1.46, a sampling area of 1000 x 100 pixels (69% of whole image) became necessary. This suggests that a large-size dispersion of element sizes in an image requires increasingly larger sampling areas or a larger number of images.

Course Shopping in Urban Community Colleges: An Analysis of Student Drop and Add Activities

ERIC Educational Resources Information Center

Hagedorn, Linda Serra; Maxwell, William E.; Cypers, Scott; Moon, Hye Sun; Lester, Jaime

2007-01-01

This study examined the course shopping behaviors among a sample of approximately 5,000 community college students enrolled across nine campuses of a large urban district. The sample was purposely designed as an analytic, rather than a random, sample that sought to obtain adequate numbers of students in course areas that were of theoretical and of…

Assessment of soil and water contaminants from selected locations in and near the Idaho Army National Guard Orchard Training Area, Ada County, Idaho, 2001-2003

USGS Publications Warehouse

Parliman, D.J.

2004-01-01

In 2001, the National Guard Bureau and the U.S. Geological Survey began a project to compile hydrogeologic data and determine presence or absence of soil, surface-water, and ground-water contamination at the Idaho Army National Guard Orchard Training Area in southwestern Idaho. Between June 2002 and April 2003, a total of 114 soil, surface-water, ground-water, precipitation, or dust samples were collected from 68 sample sites (65 different locations) in the Orchard Training Area (OTA) or along the vehicle corridor to the OTA. Soil and water samples were analyzed for concentrations of selected total trace metals, major ions, nutrients, explosive compounds, semivolatile organics, and petroleum hydrocarbons. Water samples also were analyzed for concentrations of selected dissolved trace metals and major ions. Distinguishing naturally occurring large concentrations of trace metals, major ions, and nutrients from contamination related to land and water uses at the OTA was difficult. There were no historical analyses for this area to compare with modern data, and although samples were collected from 65 locations in and near the OTA, sampled areas represented only a small part of the complex OTA land-use areas and soil types. For naturally occurring compounds, several assumptions were made?anomalously large concentrations, when tied to known land uses, may indicate presence of contamination; naturally occurring concentrations cannot be separated from contamination concentrations in mid- and lower ranges of data; and smallest concentrations may represent the lowest naturally occurring range of concentrations and (or) the absence of contaminants related to land and water uses. Presence of explosive, semivolatile organic (SVOC), and petroleum hydrocarbon compounds in samples indicates contamination from land and water uses. In areas along the vehicle corridor and major access roads within the OTA, most trace metal, major ion, and nutrient concentrations in soil samples were not in the upper 10th percentile of data, but concentrations of 25 metals, ions, or nutrients were in the upper 10th percentile in a puddle sample near the heavy equipment maneuvering area, MPRC-H. The largest concentrations of tin, ammonia, and nitrite plus nitrate (as nitrogen) in water from the OTA were detected in a sample from this puddle. Petroleum hydrocarbons were the most common contaminant, detected in all soil and surface-water samples. An SVOC, bis (2-ethylhexyl) phthalate, a plasticizer, was detected at a site along the vehicle corridor. In Maneuver Areas within the OTA, many soil samples contained at least one trace metal, major ion, or nutrient in the upper 10th percentile of data, and the largest concentrations of cobalt, iron, mercury, titanium, sodium, ammonia, or total phosphorus were detected in 6 of 13 soil samples outside the Tadpole Lake area. The largest concentrations of aluminum, arsenic, beryllium, nickel, selenium, silver, strontium, thallium, vanadium, chloride, potassium, sulfate, and nitrite plus nitrate were detected in soil samples from the Tadpole Lake area. Water from Tadpole Lake contained the largest total concentrations of 19 trace metals, 4 major ions, and 1 nutrient. Petroleum hydrocarbons were detected in 5 soil samples and water from Tadpole Lake. SVOCs related to combustion of fuel or plasticizers were detected in 1 soil sample. Explosive compounds were detected in 1 precipitation sample.In the Impact Area within the OTA, most soil samples contained at least one trace metal, major ion, or nutrient in the upper 10th percentile of data, and the largest concentrations of barium, chromium, copper, manganese, lead, or orthophosphate were detected in 6 of the 18 soil samples. Petroleum hydrocarbons were detected in 4 soil samples, SVOCs in 6 samples, and explosive compounds in 4 samples. In the mobilization and training equipment site (MATES) compound adjacent to the OTA, all soil and water samples contained at lea

Adapting geostatistics to analyze spatial and temporal trends in weed populations

USDA-ARS?s Scientific Manuscript database

Geostatistics were originally developed in mining to estimate the location, abundance and quality of ore over large areas from soil samples to optimize future mining efforts. Here, some of these methods were adapted to weeds to account for a limited distribution area (i.e., inside a field), variatio...

INTEGRATING FIELD-BASED SAMPLING AND LANDSCAPE DATA FOR REGIONAL SCALE ASSESSMENTS: EXAMPLES FROM THE UNITED STATES MID-ATLANTIC REGION

EPA Science Inventory

Spatially explicit identification of status and changes in ecological conditions over large, regional areas is key to targeting and prioritizing areas for potential further study and environmental protection and restoration. A critical limitation to this point has been our abili...

Use of LANDSAT data to assess waterfowl habitat quality

NASA Technical Reports Server (NTRS)

Colwell, J. E.; Gilmer, D. S. (Principal Investigator); Work, E. A., Jr.; Rebel, D. L.; Roller, N. E. G.

1978-01-01

The author has identified the following significant results. The capability of mapping ponds over a very large area was demonstrated, with multidate, multiframe LANDSAT imagery. A small double sample of aircraft data made it possible to adjust a LANDSAT large area census. Terrain classification was improved by using multitemporal LANDSAT data. Waterfowl production was estimated, using remotely determined pond data, in conjunction with FWS estimates of breeding population. Relative waterfowl habitat quality was characterized on a section by section basis.

Combining large area fluorescence with multiphoton microscopy for improved detection of oral epithelial neoplasia (Conference Presentation)

NASA Astrophysics Data System (ADS)

Pal, Rahul; Yang, Jinping; Qiu, Suimin; McCammon, Susan; Resto, Vicente; Vargas, Gracie

2016-03-01

Volumetric Multiphoton Autofluorescence Microscopy (MPAM) and Second Harmonic Generation Microscopy (SHGM) show promise for revealing indicators of neoplasia representing the complex microstructural organization of mucosa, potentially providing high specificity for detection of neoplasia, but is limited by small imaging area. Large area fluorescence methods on the other hand show high sensitivity appropriate for screening but are hampered by low specificity. In this study, we apply MPAM-SHGM following guidance from large area fluorescence, by either autofluorescence or a targeted metabolic fluorophore, as a potentially clinically viable approach for detection of oral neoplasia. Sites of high neoplastic potentially were identified by large area red/green autofluorescence or by a fluorescently labelled deoxy-glucose analog, 2-deoxy-2-[(7-nitro-2,1,3-benzoxadiazol-4-yl)amino]-D-glucose (2-NBDG) to highlight areas of high glucose uptake across the buccal pouch of a hamster model for OSCC. Follow-up MPAM-SHGM was conducted on regions of interests (ROIs) to assess whether microscopy would reveal microscopic features associated with neoplasia to confirm or exclude large area fluorescence findings. Parameters for analysis included cytologic metrics, 3D epithelial connective tissue interface metrics (MPAM-SHGM) and intensity of fluorescence (widefield). Imaged sites were biopsied and processed for histology and graded by a pathologist. A small sample of human ex vivo tissues were also imaged. A generalized linear model combining image metrics from large area fluorescence and volumetric MPAM-SHGM indicated the ability to delineate normal and inflammation from neoplasia.

Quantitative analysis of defects in silicon: Silicon sheet growth development for the large area silicon sheet task of the low cost solar array project

NASA Technical Reports Server (NTRS)

Natesh, R.; Smith, J. M.; Qidwai, H. A.

1978-01-01

The various steps involved in the chemical polishing and etching of silicon samples are described and the data on twins, grain boundaries and dislocation pits from fifty-three (53) samples are discussed.

Integrating sphere based reflectance measurements for small-area semiconductor samples

NASA Astrophysics Data System (ADS)

Saylan, S.; Howells, C. T.; Dahlem, M. S.

2018-05-01

This article describes a method that enables reflectance spectroscopy of small semiconductor samples using an integrating sphere, without the use of additional optical elements. We employed an inexpensive sample holder to measure the reflectance of different samples through 2-, 3-, and 4.5-mm-diameter apertures and applied a mathematical formulation to remove the bias from the measured spectra caused by illumination of the holder. Using the proposed method, the reflectance of samples fabricated using expensive or rare materials and/or low-throughput processes can be measured. It can also be incorporated to infer the internal quantum efficiency of small-area, research-level solar cells. Moreover, small samples that reflect light at large angles and develop scattering may also be measured reliably, by virtue of an integrating sphere insensitive to directionalities.

Contemporaneous VLBA 5 GHz Observations of Large Area Telescope Detected Blazars

DTIC Science & Technology

2012-01-10

Polarimetry Survey (VIPS) have been included in the sample, as well as 142 sources not found in VIPS. This very large, 5 GHz flux-limited sample of active...observing runs were follow-up observations on 90 sources in the VLBA Imaging and Polarimetry Survey (VIPS; Helmboldt et al. 2007) and new 5 GHz observations...Array (VLBA). In total, 232 sources were observed with the VLBA. Ninety sources that were previously observed as part of the VLBA Imaging and Polarimetry

Application of laboratory permeability data

USGS Publications Warehouse

Johnson, A.I.

1963-01-01

Some of the basic material contained in this report originally was prepared in 1952 as instructional handouts for ground-water short courses and for training of foreign participants. The material has been revised and expanded and is presented in the present form to make it more readily available to the field hydrologist. Illustrations now present published examples of the applications suggested in the 1952 material. For small areas, a field pumping test is sufficient to predict the characteristics of an aquifer. With a large area under study, the aquifer properties must be determined at many different locations and it is not usually economically feasible to make sufficient field tests to define the aquifer properties in detail for the whole aquifer. By supplementing a few field tests with laboratory permeability data and geologic interpretation, more point measurements representative of the hydrologic properties of the aquifer may be obtained. A sufficient number of samples seldom can be obtained to completely identify the permeability or transmissibility in detail for a project area. However, a few judiciously chosen samples of high quality, combined with good geologic interpretation, often will permit the extrapolation of permeability information over a large area with a fair degree of reliability. The importance of adequate geologic information, as well as the importance of collecting samples representative of at least all major textural units lying within the section or area of study, cannot be overemphasized.

Two phase sampling for wheat acreage estimation. [large area crop inventory experiment

NASA Technical Reports Server (NTRS)

Thomas, R. W.; Hay, C. M.

1977-01-01

A two phase LANDSAT-based sample allocation and wheat proportion estimation method was developed. This technique employs manual, LANDSAT full frame-based wheat or cultivated land proportion estimates from a large number of segments comprising a first sample phase to optimally allocate a smaller phase two sample of computer or manually processed segments. Application to the Kansas Southwest CRD for 1974 produced a wheat acreage estimate for that CRD within 2.42 percent of the USDA SRS-based estimate using a lower CRD inventory budget than for a simulated reference LACIE system. Factor of 2 or greater cost or precision improvements relative to the reference system were obtained.

High axial resolution imaging system for large volume tissues using combination of inclined selective plane illumination and mechanical sectioning

PubMed Central

Zhang, Qi; Yang, Xiong; Hu, Qinglei; Bai, Ke; Yin, Fangfang; Li, Ning; Gang, Yadong; Wang, Xiaojun; Zeng, Shaoqun

2017-01-01

To resolve fine structures of biological systems like neurons, it is required to realize microscopic imaging with sufficient spatial resolution in three dimensional systems. With regular optical imaging systems, high lateral resolution is accessible while high axial resolution is hard to achieve in a large volume. We introduce an imaging system for high 3D resolution fluorescence imaging of large volume tissues. Selective plane illumination was adopted to provide high axial resolution. A scientific CMOS working in sub-array mode kept the imaging area in the sample surface, which restrained the adverse effect of aberrations caused by inclined illumination. Plastic embedding and precise mechanical sectioning extended the axial range and eliminated distortion during the whole imaging process. The combination of these techniques enabled 3D high resolution imaging of large tissues. Fluorescent bead imaging showed resolutions of 0.59 μm, 0.47μm, and 0.59 μm in the x, y, and z directions, respectively. Data acquired from the volume sample of brain tissue demonstrated the applicability of this imaging system. Imaging of different depths showed uniform performance where details could be recognized in either the near-soma area or terminal area, and fine structures of neurons could be seen in both the xy and xz sections. PMID:29296503

Large-scale mapping and predictive modeling of submerged aquatic vegetation in a shallow eutrophic lake.

PubMed

Havens, Karl E; Harwell, Matthew C; Brady, Mark A; Sharfstein, Bruce; East, Therese L; Rodusky, Andrew J; Anson, Daniel; Maki, Ryan P

2002-04-09

A spatially intensive sampling program was developed for mapping the submerged aquatic vegetation (SAV) over an area of approximately 20,000 ha in a large, shallow lake in Florida, U.S. The sampling program integrates Geographic Information System (GIS) technology with traditional field sampling of SAV and has the capability of producing robust vegetation maps under a wide range of conditions, including high turbidity, variable depth (0 to 2 m), and variable sediment types. Based on sampling carried out in August-September 2000, we measured 1,050 to 4,300 ha of vascular SAV species and approximately 14,000 ha of the macroalga Chara spp. The results were similar to those reported in the early 1990s, when the last large-scale SAV sampling occurred. Occurrence of Chara was strongly associated with peat sediments, and maximal depths of occurrence varied between sediment types (mud, sand, rock, and peat). A simple model of Chara occurrence, based only on water depth, had an accuracy of 55%. It predicted occurrence of Chara over large areas where the plant actually was not found. A model based on sediment type and depth had an accuracy of 75% and produced a spatial map very similar to that based on observations. While this approach needs to be validated with independent data in order to test its general utility, we believe it may have application elsewhere. The simple modeling approach could serve as a coarse-scale tool for evaluating effects of water level management on Chara populations.

A fast and reliable readout method for quantitative analysis of surface-enhanced Raman scattering nanoprobes on chip surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chang, Hyejin; Jeong, Sinyoung; Ko, Eunbyeol

2015-05-15

Surface-enhanced Raman scattering techniques have been widely used for bioanalysis due to its high sensitivity and multiplex capacity. However, the point-scanning method using a micro-Raman system, which is the most common method in the literature, has a disadvantage of extremely long measurement time for on-chip immunoassay adopting a large chip area of approximately 1-mm scale and confocal beam point of ca. 1-μm size. Alternative methods such as sampled spot scan with high confocality and large-area scan method with enlarged field of view and low confocality have been utilized in order to minimize the measurement time practically. In this study, wemore » analyzed the two methods in respect of signal-to-noise ratio and sampling-led signal fluctuations to obtain insights into a fast and reliable readout strategy. On this basis, we proposed a methodology for fast and reliable quantitative measurement of the whole chip area. The proposed method adopted a raster scan covering a full area of 100 μm × 100 μm region as a proof-of-concept experiment while accumulating signals in the CCD detector for single spectrum per frame. One single scan with 10 s over 100 μm × 100 μm area yielded much higher sensitivity compared to sampled spot scanning measurements and no signal fluctuations attributed to sampled spot scan. This readout method is able to serve as one of key technologies that will bring quantitative multiplexed detection and analysis into practice.« less

Exploring proximity effects and large depth of field in helium ion beam lithography: large-area dense patterns and tilted surface exposure.

PubMed

Flatabø, Ranveig; Agarwal, Akshay; Hobbs, Richard; Greve, Martin M; Holst, Bodil; Berggren, Karl K

2018-07-06

Helium ion beam lithography (HIL) is an emerging nanofabrication technique. It benefits from a reduced interaction volume compared to that of an electron beam of similar energy, and hence reduced long-range scattering (proximity effect), higher resist sensitivity and potentially higher resolution. Furthermore, the small angular spread of the helium ion beam gives rise to a large depth of field. This should enable patterning on tilted and curved surfaces without the need of any additional adjustments, such as laser-auto focus. So far, most work on HIL has been focused on exploiting the reduced proximity effect to reach single-digit nanometer resolution, and has thus been concentrated on single-pixel exposures over small areas. Here we explore two new areas of application. Firstly, we investigate the proximity effect in large-area exposures and demonstrate HIL's capabilities in fabricating precise high-density gratings on large planar surfaces (100 μm × 100 μm, with pitch down to 35 nm) using an area dose for exposure. Secondly, we exploit the large depth of field by making the first HIL patterns on tilted surfaces (sample stage tilted 45°). We demonstrate a depth of field greater than 100 μm for a resolution of about 20 nm.

Methodology for Augmenting Existing Paths with Additional Parallel Transects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, John E.

2013-09-30

Visual Sample Plan (VSP) is sample planning software that is used, among other purposes, to plan transect sampling paths to detect areas that were potentially used for munition training. This module was developed for application on a large site where existing roads and trails were to be used as primary sampling paths. Gap areas between these primary paths needed to found and covered with parallel transect paths. These gap areas represent areas on the site that are more than a specified distance from a primary path. These added parallel paths needed to optionally be connected together into a single path—themore » shortest path possible. The paths also needed to optionally be attached to existing primary paths, again with the shortest possible path. Finally, the process must be repeatable and predictable so that the same inputs (primary paths, specified distance, and path options) will result in the same set of new paths every time. This methodology was developed to meet those specifications.« less

Triangle area water supply monitoring project, October 1988 through September 2001, North Carolina -- description of the water-quality network, sampling and analysis methods, and quality-assurance practices

USGS Publications Warehouse

Oblinger, Carolyn J.

2004-01-01

The Triangle Area Water Supply Monitoring Project was initiated in October 1988 to provide long-term water-quality data for six area water-supply reservoirs and their tributaries. In addition, the project provides data that can be used to determine the effectiveness of large-scale changes in water-resource management practices, document differences in water quality among water-supply types (large multiuse reservoir, small reservoir, run-of-river), and tributary-loading and in-lake data for water-quality modeling of Falls and Jordan Lakes. By September 2001, the project had progressed in four phases and included as many as 34 sites (in 1991). Most sites were sampled and analyzed by the U.S. Geological Survey. Some sites were already a part of the North Carolina Division of Water Quality statewide ambient water-quality monitoring network and were sampled by the Division of Water Quality. The network has provided data on streamflow, physical properties, and concentrations of nutrients, major ions, metals, trace elements, chlorophyll, total organic carbon, suspended sediment, and selected synthetic organic compounds. Project quality-assurance activities include written procedures for sample collection, record management and archive, collection of field quality-control samples (blank samples and replicate samples), and monitoring the quality of field supplies. In addition to project quality-assurance activities, the quality of laboratory analyses was assessed through laboratory quality-assurance practices and an independent laboratory quality-control assessment provided by the U.S. Geological Survey Branch of Quality Systems through the Blind Inorganic Sample Project and the Organic Blind Sample Project.

Phytotoxic substances in runoff from forested catchment areas

NASA Astrophysics Data System (ADS)

Grimvall, Anders; Bengtsson, Maj-Britt; Borén, Hans; Wahlström, Dan

Runoff from different catchment areas in southern Sweden was tested in a root bioassay based on solution cultures of cucumber seedlings. Water samples from agricultural catchment areas produced no signs at all or only weak signs of inhibited root growth, whereas several water samples from catchment areas dominated by mires or coniferous forests produced visible root injuries. The most severe root injuries (very short roots, discolouration, swelling of root tips and lack of root hairs) were caused by samples from a catchment area without local emissions and dominated by old stands of spruce. Fractionation by ultrafiltration showed that the phytotoxic effect of these samples could be attributed to organic matter with a nominal molecular-weight exceeding 1000 or to substances associated with organic macromolecules. Experiments aimed at concentrating phytotoxic compounds from surface water indicated that the observed growth inhibition was caused by strongly hydrophilic substances. Previous reports on phytotoxic, organic substances of natural origin have emphasized interaction between plants growing close together. The presence of phytotoxic substances in runoff indicates that there is also a large-scale dispersion of such compounds.

Semi-automatic surface sediment sampling system - A prototype to be implemented in bivalve fishing surveys

NASA Astrophysics Data System (ADS)

Rufino, Marta M.; Baptista, Paulo; Pereira, Fábio; Gaspar, Miguel B.

2018-01-01

In the current work we propose a new method to sample surface sediment during bivalve fishing surveys. Fishing institutes all around the word carry out regular surveys with the aim of monitoring the stocks of commercial species. These surveys comprise often more than one hundred of sampling stations and cover large geographical areas. Although superficial sediment grain sizes are among the main drivers of benthic communities and provide crucial information for studies on coastal dynamics, overall there is a strong lack of this type of data, possibly, because traditional surface sediment sampling methods use grabs, that require considerable time and effort to be carried out on regular basis or on large areas. In face of these aspects, we developed an easy and un-expensive method to sample superficial sediments, during bivalve fisheries monitoring surveys, without increasing survey time or human resources. The method was successfully evaluated and validated during a typical bivalve survey carried out on the Northwest coast of Portugal, confirming that it had any interference with the survey objectives. Furthermore, the method was validated by collecting samples using a traditional Van Veen grabs (traditional method), which showed a similar grain size composition to the ones collected by the new method, on the same localities. We recommend that the procedure is implemented on regular bivalve fishing surveys, together with an image analysis system to analyse the collected samples. The new method will provide substantial quantity of data on surface sediment in coastal areas, using a non-expensive and efficient manner, with a high potential application in different fields of research.

Mental health and substance abuse characteristics among a clinical sample of urban American Indian/Alaska native youths in a large California metropolitan area: a descriptive study.

PubMed

Dickerson, Daniel L; Johnson, Carrie L

2012-02-01

This study analyzes descriptive data among a clinical sample of American Indian/Alaska Native (AI/AN) youths receiving mental health services in a large California metropolitan area. Among 118 urban AI/AN youths, mood disorders (41.5%) and adjustment disorder (35.4%) were the most common mental health diagnoses. Alcohol (69.2%) and marijuana (50.0%) were the most commonly used substances. Witnessing domestic violence (84.2%) and living with someone who had a substance abuse problem (64.7%) were reported. The majority of patients demonstrated various behavior and emotional problems. Enhancing culturally relevant mental health and substance abuse treatment and prevention programs for urban AI/AN youth is suggested.

Reconnaissance investigation of brine in the eastern Rub al Khali, Kingdom of Saudi Arabia

USGS Publications Warehouse

Smith, C.L.

1981-01-01

Al Uruq al Mu'taridah-Umm as Samim area is located in a large topographic depression in the eastern Rub al Khali desert where playas several thousand square kilometers in area are exposedo A crust of eolian sand cemented with gypsum and halite has formed on many playa surfaces. Anhydrite nodules are common in the sampled area, where the depth to ground water generally exceeds 172 Cmo The chemistry of the three ground-water samples collected near the water well Ramallah-1 (lat 22?10'20'' N., long 54?20'37'' E.) is similar to that of sabkhah-related brines on the coast of the United Arab Emirates. Although there is no indication of economic quantities of evaporite minerals in the sampled area, the extent of the depression and its unique geologic environment recommend it for resource-evaluation studies.

PROPOSED STANDARDIZED ASSESSMENT METHODS (SAMS) FOR ELECTROFISHING LARGE RIVERS

EPA Science Inventory

The effects of electrofishing design and sampling distance were studied at 49 sites across four boatable rivers ranging in drainage area from 13,947 to 23,041 km2 in the Ohio River basin. Two general types of sites were sampled: Run-of-the-River (Free-flowing sites or with smal...

Production ecology of Thuja occidentalis

Treesearch

Philip V. Hofmeyer; Robert S. Seymour; Laura S. Kenefic

2010-01-01

Equations to predict branch and tree leaf area, foliar mass, and stemwood volume were developed from 25 destructively sampled northern white-cedar (Thuja occidentalis L.) trees, a species whose production ecology has not been studied. Resulting models were applied to a large sample of 296 cored trees from 60 sites stratified across a soil gradient...

Silicon sheet growth development for the large area silicon sheet task of the low cost solar array project. Quantitative analysis of defects in silicon

NASA Technical Reports Server (NTRS)

Natesh, R.

1978-01-01

The various steps involved in obtaining quantitative information of structural defects in crystalline silicon samples are described. Procedures discussed include: (1) chemical polishing; (2) chemical etching; and (3) automated image analysis of samples on the QTM 720 System.

Spatial inventory integrating raster databases and point sample data. [Geographic Information System for timber inventory

NASA Technical Reports Server (NTRS)

Strahler, A. H.; Woodcock, C. E.; Logan, T. L.

1983-01-01

A timber inventory of the Eldorado National Forest, located in east-central California, provides an example of the use of a Geographic Information System (GIS) to stratify large areas of land for sampling and the collection of statistical data. The raster-based GIS format of the VICAR/IBIS software system allows simple and rapid tabulation of areas, and facilitates the selection of random locations for ground sampling. Algorithms that simplify the complex spatial pattern of raster-based information, and convert raster format data to strings of coordinate vectors, provide a link to conventional vector-based geographic information systems.

Seabed gamma-ray spectrometry: applications at IAEA-MEL.

PubMed

Osvath, I; Povinec, P P

2001-01-01

The technique of underwater gamma-ray spectrometry has been developed to complement or replace the traditional sampling-sample analysis approach for applications with space-time constraints, e.g. large areas of investigation, emergency response or long-term monitoring. IAEA-MEL has used both high-efficiency NaI(Tl) and high-resolution HPGe spectrometry to investigate contamination with anthropogenic radionuclides in a variety of marine environments. Surveys at the South Pacific nuclear test sites of Mururoa and Fangataufa have been used to guide sampling in areas of high contamination around ground zero points. In the Irish Sea offshore from the Sellafield nuclear reprocessing plant, a gamma-ray survey of seabed sediment was carried out to obtain estimates of the distribution and subsequently, for the inventory of 137Cs in the investigated area.

Preservation of mitochondrial functional integrity in mitochondria isolated from small cryopreserved mouse brain areas.

PubMed

Valenti, Daniela; de Bari, Lidia; De Filippis, Bianca; Ricceri, Laura; Vacca, Rosa Anna

2014-01-01

Studies of mitochondrial bioenergetics in brain pathophysiology are often precluded by the need to isolate mitochondria immediately after tissue dissection from a large number of brain biopsies for comparative studies. Here we present a procedure of cryopreservation of small brain areas from which mitochondrial enriched fractions (crude mitochondria) with high oxidative phosphorylation efficiency can be isolated. Small mouse brain areas were frozen and stored in a solution containing glycerol as cryoprotectant. Crude mitochondria were isolated by differential centrifugation from both cryopreserved and freshly explanted brain samples and were compared with respect to their ability to generate membrane potential and produce ATP. Intactness of outer and inner mitochondrial membranes was verified by polarographic ascorbate and cytochrome c tests and spectrophotometric assay of citrate synthase activity. Preservation of structural integrity and oxidative phosphorylation efficiency was successfully obtained in crude mitochondria isolated from different areas of cryopreserved mouse brain samples. Long-term cryopreservation of small brain areas from which intact and phosphorylating mitochondria can be isolated for the study of mitochondrial bioenergetics will significantly expand the study of mitochondrial defects in neurological pathologies, allowing large comparative studies and favoring interlaboratory and interdisciplinary analyses. Copyright © 2013 Elsevier Inc. All rights reserved.

Eucalyptus plantations for energy production in Hawaii. 1980 annual report, January 1980-December 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitesell, C. D.

1980-01-01

In 1980 200 acres of eucalyptus trees were planted for a research and development biomass energy plantation bringing the total area under cultivation to 300 acres. Of this total acreage, 90 acres or 30% was planted in experimental plots. The remaining 70% of the cultivated area was closely monitored to determine the economic cost/benefit ratio of large scale biomass energy production. In the large scale plantings, standard field practices were set up for all phases of production: nursery, clearing, planting, weed control and fertilization. These practices were constantly evaluated for potential improvements in efficiency and reduced cost. Promising experimental treatmentsmore » were implemented on a large scale to test their effectiveness under field production conditions. In the experimental areas all scheduled data collection in 1980 has been completed and most measurements have been keypunched and analyzed. Soil samples and leaf samples have been analyzed for nutrient concentrations. Crop logging procedures have been set up to monitor tree growth through plant tissue analysis. An intensive computer search on biomass, nursery practices, harvesting equipment and herbicide applications has been completed through the services of the US Forest Service.« less

Uranium content of ground and surface waters in western Kansas, eastern Colorado, and the Oklahoma Panhande

USGS Publications Warehouse

Landis, E.R.

1956-01-01

and in some parts of the report area, such as the Cimarron River area of westernmost Oklahoma and northeastern New Mexico, and the Rule Creek area in Bent and Las Animas Counties, Colo. , most, or all, of the water samples collected contain relatively large amounts of uranium. Further exploration to determine the source of the uranium in the water from these rock units and areas may be worthwhile.

Particle size and surface area effects on the thin-pulse shock initiation of Diaminoazoxyfurazan (DAAF)

NASA Astrophysics Data System (ADS)

Burritt, Rosemary; Francois, Elizabeth; Windler, Gary; Chavez, David

2017-06-01

Diaminoazoxyfurazan (DAAF) has many of the safety characteristics of an insensitive high explosive (IHE): it is extremely insensitive to impact and friction and is comparable to triaminotrinitrobezene (TATB) in this way. Conversely, it demonstrates many performance characteristics of a Conventional High Explosive (CHE). DAAF has a small failure diameter of about 1.25 mm and can be sensitive to shock under the right conditions. Large particle sized DAAF will not initiate in a typical exploding foil initiator (EFI) configuration but smaller particle sizes will. Large particle sized DAAF, of 40 μm, was crash precipitated and ball milled into six distinct samples and pressed into pellets with a density of 1.60 g/cc (91% TMD). To investigate the effect of particle size and surface area on the direct initiation on DAAF multiple threshold tests were preformed on each sample of DAAF in different EFI configurations, which varied in flyer thickness and/or bridge size. Comparative tests were performed examining threshold voltage and correlated to Photon Doppler Velocimetry (PDV) results. The samples with larger particle sizes and surface area required more energy to initiate while the smaller particle sizes required less energy and could be initiated with smaller diameter flyers.

Geochemical sampling in arid environments by the U.S. Geological Survey

USGS Publications Warehouse

Hinkle, Margaret E.

1988-01-01

The U.S. Geological Survey (USGS) is responsible for the geochemical evaluations used for mineral resource assessments of large tracts of public lands in the Western United States. Many of these lands are administered by the Bureau of Land Management (BLM) and are studied to determine their suitability or nonsuitability for wilderness designation. Much of the Western United States is arid or semiarid. This report discusses various geochemical sample media that have been used for evaluating areas in arid environments and describes case histories in BLM wilderness study areas in which stream-sediment and heavy-mineral-concentrate sample media were compared. As a result of these case history studies, the nonmagnetic fraction of panned heavy-mineral concentrates was selected as the most effective medium for reconnaissance geochemical sampling for resources other than gold, in arid areas. Nonmagnetic heavy-mineral-concentrate samples provide the primary analytical information currently used in geochemical interpretations of mineral resource potential assessment of BLM lands.

Notes for Brazil sampling frame evaluation trip

NASA Technical Reports Server (NTRS)

Horvath, R. (Principal Investigator); Hicks, D. R. (Compiler)

1981-01-01

Field notes describing a trip conducted in Brazil are presented. This trip was conducted for the purpose of evaluating a sample frame developed using LANDSAT full frame images by the USDA Economic and Statistics Service for the eventual purpose of cropland production estimation with LANDSAT by the Foreign Commodity Production Forecasting Project of the AgRISTARS program. Six areas were analyzed on the basis of land use, crop land in corn and soybean, field size and soil type. The analysis indicated generally successful use of LANDSAT images for purposes of remote large area land use stratification.

Domain-Adapted Convolutional Networks for Satellite Image Classification: A Large-Scale Interactive Learning Workflow

DOE PAGES

Lunga, Dalton D.; Yang, Hsiuhan Lexie; Reith, Andrew E.; ...

2018-02-06

Satellite imagery often exhibits large spatial extent areas that encompass object classes with considerable variability. This often limits large-scale model generalization with machine learning algorithms. Notably, acquisition conditions, including dates, sensor position, lighting condition, and sensor types, often translate into class distribution shifts introducing complex nonlinear factors and hamper the potential impact of machine learning classifiers. Here, this article investigates the challenge of exploiting satellite images using convolutional neural networks (CNN) for settlement classification where the class distribution shifts are significant. We present a large-scale human settlement mapping workflow based-off multiple modules to adapt a pretrained CNN to address themore » negative impact of distribution shift on classification performance. To extend a locally trained classifier onto large spatial extents areas we introduce several submodules: First, a human-in-the-loop element for relabeling of misclassified target domain samples to generate representative examples for model adaptation; second, an efficient hashing module to minimize redundancy and noisy samples from the mass-selected examples; and third, a novel relevance ranking module to minimize the dominance of source example on the target domain. The workflow presents a novel and practical approach to achieve large-scale domain adaptation with binary classifiers that are based-off CNN features. Experimental evaluations are conducted on areas of interest that encompass various image characteristics, including multisensors, multitemporal, and multiangular conditions. Domain adaptation is assessed on source–target pairs through the transfer loss and transfer ratio metrics to illustrate the utility of the workflow.« less

Domain-Adapted Convolutional Networks for Satellite Image Classification: A Large-Scale Interactive Learning Workflow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lunga, Dalton D.; Yang, Hsiuhan Lexie; Reith, Andrew E.

Satellite imagery often exhibits large spatial extent areas that encompass object classes with considerable variability. This often limits large-scale model generalization with machine learning algorithms. Notably, acquisition conditions, including dates, sensor position, lighting condition, and sensor types, often translate into class distribution shifts introducing complex nonlinear factors and hamper the potential impact of machine learning classifiers. Here, this article investigates the challenge of exploiting satellite images using convolutional neural networks (CNN) for settlement classification where the class distribution shifts are significant. We present a large-scale human settlement mapping workflow based-off multiple modules to adapt a pretrained CNN to address themore » negative impact of distribution shift on classification performance. To extend a locally trained classifier onto large spatial extents areas we introduce several submodules: First, a human-in-the-loop element for relabeling of misclassified target domain samples to generate representative examples for model adaptation; second, an efficient hashing module to minimize redundancy and noisy samples from the mass-selected examples; and third, a novel relevance ranking module to minimize the dominance of source example on the target domain. The workflow presents a novel and practical approach to achieve large-scale domain adaptation with binary classifiers that are based-off CNN features. Experimental evaluations are conducted on areas of interest that encompass various image characteristics, including multisensors, multitemporal, and multiangular conditions. Domain adaptation is assessed on source–target pairs through the transfer loss and transfer ratio metrics to illustrate the utility of the workflow.« less

Virtual Observatories, Data Mining, and Astroinformatics

NASA Astrophysics Data System (ADS)

Borne, Kirk

The historical, current, and future trends in knowledge discovery from data in astronomy are presented here. The story begins with a brief history of data gathering and data organization. A description of the development ofnew information science technologies for astronomical discovery is then presented. Among these are e-Science and the virtual observatory, with its data discovery, access, display, and integration protocols; astroinformatics and data mining for exploratory data analysis, information extraction, and knowledge discovery from distributed data collections; new sky surveys' databases, including rich multivariate observational parameter sets for large numbers of objects; and the emerging discipline of data-oriented astronomical research, called astroinformatics. Astroinformatics is described as the fourth paradigm of astronomical research, following the three traditional research methodologies: observation, theory, and computation/modeling. Astroinformatics research areas include machine learning, data mining, visualization, statistics, semantic science, and scientific data management.Each of these areas is now an active research discipline, with significantscience-enabling applications in astronomy. Research challenges and sample research scenarios are presented in these areas, in addition to sample algorithms for data-oriented research. These information science technologies enable scientific knowledge discovery from the increasingly large and complex data collections in astronomy. The education and training of the modern astronomy student must consequently include skill development in these areas, whose practitioners have traditionally been limited to applied mathematicians, computer scientists, and statisticians. Modern astronomical researchers must cross these traditional discipline boundaries, thereby borrowing the best of breed methodologies from multiple disciplines. In the era of large sky surveys and numerous large telescopes, the potential for astronomical discovery is equally large, and so the data-oriented research methods, algorithms, and techniques that are presented here will enable the greatest discovery potential from the ever-growing data and information resources in astronomy.

Development features in large-range nanoscale coordinate metrology

NASA Astrophysics Data System (ADS)

Gruhlke, Martin; Recknagel, Christian; Rothe, Hendrik

2008-04-01

The Nanometer-Coordinate-Measuring-Machine (NCMM) has the ability to scan large areas at nanometer resolution for the purpose of quality assurance of nanostructured products. The device combines a conventional atomic force microscope (AFM) with a precise positioning system. By locating the AFM at a fixed point and moving the sample with the positioning system a scan range of 2.5 x 2.5 x 0.5 cm 3 and a repeatability of 0.1 nm is achieved. Since all movements of the positioning system are measured via laser interferometers, the Abbe-principle is kept in every dimension, the use of materials with a low thermal expansion coefficient (like Zerodur and FeNi36) and an overall coordinate system the system provides unique measurement conditions (traceability to the meter definition; repeatable and fast scans of the region of interest). In the past the NCMM was used to make the first large area scan of a microelectronic sample. Our present work focuses on automating critical dimension measurement through the use of a-priori-knowledge of the sample and optical navigation. A-priori-knowledge can be generated by the use of CAD-Data of the sample or scans with white light interferometry. Another present objective is the optimization of the measurement parameters for specific sample topologies using simulation and also empirical methods like the Ziegler-Nichols method. The need of efficient data processing and handling is also part of our current research.

Estimating migratory fish distribution from altitude and basin area: a case study in a large Neotropical river

Treesearch

Jose Ricardo Barradas; Lucas G. Silva; Bret C. Harvey; Nelson F. Fontoura

2012-01-01

1. The objective of this study was to identify longitudinal distribution patterns of large migratory fish species in the Uruguay River basin, southern Brazil, and construct statistical distribution models for Salminus brasiliensis, Prochilodus lineatus, Leporinus obtusidens and Pseudoplatystoma corruscans. 2. The sampling programme resulted in 202 interviews with old...

Carbon pools and fluxes in small temperate forest landscapes: Variability and implications for sampling design

Treesearch

John B. Bradford; Peter Weishampel; Marie-Louise Smith; Randall Kolka; Richard A. Birdsey; Scott V. Ollinger; Michael G. Ryan

2010-01-01

Assessing forest carbon storage and cycling over large areas is a growing challenge that is complicated by the inherent heterogeneity of forest systems. Field measurements must be conducted and analyzed appropriately to generate precise estimates at scales large enough for mapping or comparison with remote sensing data. In this study we examined...

Should legislation regarding maximum Pb and Cd levels in human food also cover large game meat?

PubMed

Taggart, Mark A; Reglero, Manuel M; Camarero, Pablo R; Mateo, Rafael

2011-01-01

Game meat may be contaminated with metals and metalloids if animals reside in anthropogenically polluted areas, or if ammunition used to kill the game contaminates the meat. Muscle tissue from red deer and wild boar shot in Ciudad Real province (Spain) in 2005-06 was analysed for As, Pb, Cu, Zn, Se and Cd. Samples were collected from hunting estates within and outside an area that has been historically used for mining, smelting and refining various metals and metalloids. Meat destined for human consumption, contained more Pb, As and Se (red deer) and Pb (boar) when harvested from animals that had resided in mined areas. Age related accumulation of Cd, Zn and As (in deer) and Cd, Cu and Se (in boar) was also observed. Two boar meat samples contained high Pb, at 352 and 2408 μg/g d.w., and these were likely to have been contaminated by Pb ammunition. Likewise, 19-84% of all samples (depending on species and sampling area) had Pb levels > 0.1 μg/g w.w., the EU maximum residue level (MRL) for farm reared meat. Between 9 and 43% of samples exceeded comparable Cd limits. Such data highlight a discrepancy between what is considered safe for human consumption in popular farmed meat (chicken, beef, lamb), and what in game may often exist. A risk assessment is presented which describes the number of meals required to exceed current tolerable weekly intakes (PTWIs) for Pb and Cd, and the potential contribution of large game consumption to such intake limit criteria. Copyright © 2010 Elsevier Ltd. All rights reserved.

Areas of Left Perisylvian Cortex Mediate Auditory-Verbal Short-Term Memory

ERIC Educational Resources Information Center

Koenigs, Michael; Acheson, Daniel J.; Barbey, Aron K.; Solomon, Jeffrey; Postle, Bradley R.; Grafman, Jordan

2011-01-01

A contentious issue in memory research is whether verbal short-term memory (STM) depends on a neural system specifically dedicated to the temporary maintenance of information, or instead relies on the same brain areas subserving the comprehension and production of language. In this study, we examined a large sample of adults with acquired brain…

Landscape models of adult coho salmon density examined at four spatial extents

Treesearch

Julie C. Firman; E. Ashley Steel; David W. Jensen; Kelly M. Burnett; Kelly Christiansen; Blake E. Feist; David P. Larsen; Kara Anlauf

2011-01-01

Salmon occupy large areas over which comprehensive surveys are not feasible owing to the prohibitive expense of surveying thousands of kilometers of streams. Studies of these populations generally rely on sampling a small portion of the distribution of the species. However, managers often need information about areas that have not been visited. The availability of...

Back to Africa: Tracing Dyslexia Genes in East Africa

ERIC Educational Resources Information Center

Grigorenko, Elena L.; Naples, Adam; Chang, Joseph; Romano, Christina; Ngorosho, Damaris; Kungulilo, Selemani; Jukes, Matthew; Bundy, Donald

2007-01-01

A sample of Swahili-speaking probands with reading difficulties was identified from a large representative sample of 1,500 school children in the rural areas of Tanzania. Families of these probands (n = 88) were invited to participate in the study. The proband and his/her siblings received a battery of reading-related tasks and performance on…

Reliability Sampling Plans: A Review and Some New Results

ERIC Educational Resources Information Center

Isaic-Maniu, Alexandru; Voda, Viorel Gh.

2009-01-01

In this work we present a large area of aspects related to the problem of sampling inspection in the case of reliability. First we discuss the actual status of this domain, mentioning the newest approaches (from a technical view point) such as HALT and HASS and the statistical perspective. After a brief description of the general procedure in…

The College Environment: Contrasts Between CYCC Freshmen and Transfers and a Nationwide Freshman Sample, Fall, 1975.

ERIC Educational Resources Information Center

Kirby, E. B.

In order to analyze the environment of Central YMCA Community College (CYCC), information was requested on the Student Information Form, 1975, which dealt with three large areas: social issues, personal behavior, and future behavior in the noncollege world. This report compares the responses of three student samples--CYCC first-time entering…

Risk Factors for Severe Inter-Sibling Violence: A Preliminary Study of a Youth Forensic Sample

ERIC Educational Resources Information Center

Khan, Roxanne; Cooke, David J.

2008-01-01

The perpetration of severe inter-sibling violence (SISV) remains a largely unexplored area of family violence. This article describes an investigation of risk factors for intentional SISV perpetration. A sample of 111 young people under the care of the Scottish criminal justice or welfare systems was studied. A SISV perpetration interview schedule…

Gender Differences in Achievement in a Large, Nationally Representative Sample of Children and Adolescents

ERIC Educational Resources Information Center

Scheiber, Caroline; Reynolds, Matthew R.; Hajovsky, Daniel B.; Kaufman, Alan S.

2015-01-01

The purpose of this study was to investigate developmental gender differences in academic achievement areas, with the primary focus on writing, using the child and adolescent portion (ages 6-21 years) of the "Kaufman Test of Educational Achievement-Second Edition, Brief Form," norming sample (N = 1,574). Path analytic models with gender,…

Soil sampling and analytical strategies for mapping fallout in nuclear emergencies based on the Fukushima Dai-ichi Nuclear Power Plant accident.

PubMed

Onda, Yuichi; Kato, Hiroaki; Hoshi, Masaharu; Takahashi, Yoshio; Nguyen, Minh-Long

2015-01-01

The Fukushima Dai-ichi Nuclear Power Plant (FDNPP) accident resulted in extensive radioactive contamination of the environment via deposited radionuclides such as radiocesium and (131)I. Evaluating the extent and level of environmental contamination is critical to protecting citizens in affected areas and to planning decontamination efforts. However, a standardized soil sampling protocol is needed in such emergencies to facilitate the collection of large, tractable samples for measuring gamma-emitting radionuclides. In this study, we developed an emergency soil sampling protocol based on preliminary sampling from the FDNPP accident-affected area. We also present the results of a preliminary experiment aimed to evaluate the influence of various procedures (e.g., mixing, number of samples) on measured radioactivity. Results show that sample mixing strongly affects measured radioactivity in soil samples. Furthermore, for homogenization, shaking the plastic sample container at least 150 times or disaggregating soil by hand-rolling in a disposable plastic bag is required. Finally, we determined that five soil samples within a 3 m × 3-m area are the minimum number required for reducing measurement uncertainty in the emergency soil sampling protocol proposed here. Copyright © 2014 Elsevier Ltd. All rights reserved.

Gaussian process based intelligent sampling for measuring nano-structure surfaces

NASA Astrophysics Data System (ADS)

Sun, L. J.; Ren, M. J.; Yin, Y. H.

2016-09-01

Nanotechnology is the science and engineering that manipulate matters at nano scale, which can be used to create many new materials and devices with a vast range of applications. As the nanotech product increasingly enters the commercial marketplace, nanometrology becomes a stringent and enabling technology for the manipulation and the quality control of the nanotechnology. However, many measuring instruments, for instance scanning probe microscopy, are limited to relatively small area of hundreds of micrometers with very low efficiency. Therefore some intelligent sampling strategies should be required to improve the scanning efficiency for measuring large area. This paper presents a Gaussian process based intelligent sampling method to address this problem. The method makes use of Gaussian process based Bayesian regression as a mathematical foundation to represent the surface geometry, and the posterior estimation of Gaussian process is computed by combining the prior probability distribution with the maximum likelihood function. Then each sampling point is adaptively selected by determining the position which is the most likely outside of the required tolerance zone among the candidates and then inserted to update the model iteratively. Both simulationson the nominal surface and manufactured surface have been conducted on nano-structure surfaces to verify the validity of the proposed method. The results imply that the proposed method significantly improves the measurement efficiency in measuring large area structured surfaces.

[Occurrence of quinolone and sulfonamide antibiotics in swine and cattle manures from large-scale feeding operations of Guangdong Province].

PubMed

Tai, Yi-Ping; Luo, Xiao-Dong; Mo, Ce-Hui; Li, Yan-Wen; Wu, Xiao-Lian; Liu, Xing-Yue

2011-04-01

The occurrence and distribution of four quinolones and four sulfonamides in swine and cattle feces sampled from twenty large-scale feeding operations in different areas of Guangdong province were detected using solid phase extraction (SPE) and high performance liquid chromatography (HPLC). Quinolone and sulfonamide compounds were observed in all pig dung samples. Their total concentrations ranged from 24.5 microg/kg to 1516.2 microg/kg (F. W.) with an average of 581.0 microg/kg and ranged from 1925.9-13399.5 microg/kg with an average of 4403.9 microg/kg respectively. The dominant compounds in pig feces were ciprofloxacin and enrofloxacin for quinolones and sulfamerazine and sulfamethoxazole for sulfonamides. Quinolone compounds which dominated with norfloxacin and ciprofloxacin were also observed in all cattle dung samples, its total concentrations ranged from 73.2 microg/kg to 1328.0 microg/kg which averaged 572.9 microg/kg. While the positive rates of sulfonamide compounds detected in cattle dung samples were above 90%, predominated by sulfamethoxazole and sulfamerazine. Concentration and distribution of both quinolone and sulfonamide compounds in swine and cattle dungs of different feeding operations varied greatly. Relatively high concentrations of the two kinds of antibiotics were found in both swine and cattle dungs from Guangzhou area, while sulfameter and sulfamethazine in cattle dungs from Foshan and Shenzhen areas were below the limit of detection.

Increased tornado hazard in large metropolitan areas

NASA Astrophysics Data System (ADS)

Cusack, Stephen

2014-11-01

The tornado climate was compared between large metropolitan areas and neighbouring non-metro cities using modern tornado reports in the Storm Prediction Center (SPC) archives. Twenty large metro areas in the higher-risk region of the U.S. were used to boost sample sizes hence robustness of results. Observational biases were minimised by using the most densely populated zips. The analysis found 50% greater tornado frequency and a thicker-tailed severity distribution in metro areas compared to the non-metro cities. These differences are significant at the 1% level. Regarding tornado frequency, the primary question is whether the raised occurrence rates in metro areas are due to observation biases or real differences in tornado climate. Past studies found no relative biases at the population densities used here, whereas there are two potential urban drivers of tornadogenesis. First, the urban heat island raises the storm severity above and downwind of main urban areas, as recorded in precipitation and lightning datasets. Second, the increased surface roughness over metro areas raises low-level shear which in turn has been found to be favourable for tornadogenesis. Modification of convective storms over large metro areas is the more plausible explanation of raised tornado frequency. The drivers of a thicker-tailed tornado severity distribution in metro areas are less certain. Potential causes include: increased debris-loading in metro tornadoes; modification of storms' lower boundary layer by increased surface roughness in metro areas; the reduced density of damage indicators in non-metro cities.

SAS procedures for designing and analyzing sample surveys

USGS Publications Warehouse

Stafford, Joshua D.; Reinecke, Kenneth J.; Kaminski, Richard M.

2003-01-01

Complex surveys often are necessary to estimate occurrence (or distribution), density, and abundance of plants and animals for purposes of re-search and conservation. Most scientists are familiar with simple random sampling, where sample units are selected from a population of interest (sampling frame) with equal probability. However, the goal of ecological surveys often is to make inferences about populations over large or complex spatial areas where organisms are not homogeneously distributed or sampling frames are in-convenient or impossible to construct. Candidate sampling strategies for such complex surveys include stratified,multistage, and adaptive sampling (Thompson 1992, Buckland 1994).

Applying Active Learning to Assertion Classification of Concepts in Clinical Text

PubMed Central

Chen, Yukun; Mani, Subramani; Xu, Hua

2012-01-01

Supervised machine learning methods for clinical natural language processing (NLP) research require a large number of annotated samples, which are very expensive to build because of the involvement of physicians. Active learning, an approach that actively samples from a large pool, provides an alternative solution. Its major goal in classification is to reduce the annotation effort while maintaining the quality of the predictive model. However, few studies have investigated its uses in clinical NLP. This paper reports an application of active learning to a clinical text classification task: to determine the assertion status of clinical concepts. The annotated corpus for the assertion classification task in the 2010 i2b2/VA Clinical NLP Challenge was used in this study. We implemented several existing and newly developed active learning algorithms and assessed their uses. The outcome is reported in the global ALC score, based on the Area under the average Learning Curve of the AUC (Area Under the Curve) score. Results showed that when the same number of annotated samples was used, active learning strategies could generate better classification models (best ALC – 0.7715) than the passive learning method (random sampling) (ALC – 0.7411). Moreover, to achieve the same classification performance, active learning strategies required fewer samples than the random sampling method. For example, to achieve an AUC of 0.79, the random sampling method used 32 samples, while our best active learning algorithm required only 12 samples, a reduction of 62.5% in manual annotation effort. PMID:22127105

Simple room-temperature preparation of high-yield large-area graphene oxide

PubMed Central

Huang, NM; Lim, HN; Chia, CH; Yarmo, MA; Muhamad, MR

2011-01-01

Graphene has attracted much attention from researchers due to its interesting mechanical, electrochemical, and electronic properties. It has many potential applications such as polymer filler, sensor, energy conversion, and energy storage devices. Graphene-based nanocomposites are under an intense spotlight amongst researchers. A large amount of graphene is required for preparation of such samples. Lately, graphene-based materials have been the target for fundamental life science investigations. Despite graphene being a much sought-after raw material, the drawbacks in the preparation of graphene are that it is a challenge amongst researchers to produce this material in a scalable quantity and that there is a concern about its safety. Thus, a simple and efficient method for the preparation of graphene oxide (GO) is greatly desired to address these problems. In this work, one-pot chemical oxidation of graphite was carried out at room temperature for the preparation of large-area GO with ~100% conversion. This high-conversion preparation of large-area GO was achieved using a simplified Hummer’s method from large graphite flakes (an average flake size of 500 μm). It was found that a high degree of oxidation of graphite could be realized by stirring graphite in a mixture of acids and potassium permanganate, resulting in GO with large lateral dimension and area, which could reach up to 120 μm and ~8000 μm2, respectively. The simplified Hummer’s method provides a facile approach for the preparation of large-area GO. PMID:22267928

Integrating resource selection into spatial capture-recapture models for large carnivores

USGS Publications Warehouse

Proffitt, Kelly M.; Goldberg, Joshua; Hebblewite, Mark; Russell, Robin E.; Jimenez, Ben; Robinson, Hugh S.; Pilgrim, Kristine; Schwartz, Michael K.

2015-01-01

Wildlife managers need reliable methods to estimate large carnivore densities and population trends; yet large carnivores are elusive, difficult to detect, and occur at low densities making traditional approaches intractable. Recent advances in spatial capture-recapture (SCR) models have provided new approaches for monitoring trends in wildlife abundance and these methods are particularly applicable to large carnivores. We applied SCR models in a Bayesian framework to estimate mountain lion densities in the Bitterroot Mountains of west central Montana. We incorporate an existing resource selection function (RSF) as a density covariate to account for heterogeneity in habitat use across the study area and include data collected from harvested lions. We identify individuals through DNA samples collected by (1) biopsy darting mountain lions detected in systematic surveys of the study area, (2) opportunistically collecting hair and scat samples, and (3) sampling all harvested mountain lions. We included 80 DNA samples collected from 62 individuals in the analysis. Including information on predicted habitat use as a covariate on the distribution of activity centers reduced the median estimated density by 44%, the standard deviation by 7%, and the width of 95% credible intervals by 10% as compared to standard SCR models. Within the two management units of interest, we estimated a median mountain lion density of 4.5 mountain lions/100 km2 (95% CI = 2.9, 7.7) and 5.2 mountain lions/100 km2 (95% CI = 3.4, 9.1). Including harvested individuals (dead recovery) did not create a significant bias in the detection process by introducing individuals that could not be detected after removal. However, the dead recovery component of the model did have a substantial effect on results by increasing sample size. The ability to account for heterogeneity in habitat use provides a useful extension to SCR models, and will enhance the ability of wildlife managers to reliably and economically estimate density of wildlife populations, particularly large carnivores.

Whale sharks target dense prey patches of sergestid shrimp off Tanzania

PubMed Central

Rohner, Christoph A.; Armstrong, Amelia J.; Pierce, Simon J.; Prebble, Clare E. M.; Cagua, E. Fernando; Cochran, Jesse E. M.; Berumen, Michael L.; Richardson, Anthony J.

2015-01-01

Large planktivores require high-density prey patches to make feeding energetically viable. This is a major challenge for species living in tropical and subtropical seas, such as whale sharks Rhincodon typus. Here, we characterize zooplankton biomass, size structure and taxonomic composition from whale shark feeding events and background samples at Mafia Island, Tanzania. The majority of whale sharks were feeding (73%, 380 of 524 observations), with the most common behaviour being active surface feeding (87%). We used 20 samples collected from immediately adjacent to feeding sharks and an additional 202 background samples for comparison to show that plankton biomass was ∼10 times higher in patches where whale sharks were feeding (25 vs. 2.6 mg m−3). Taxonomic analyses of samples showed that the large sergestid Lucifer hanseni (∼10 mm) dominated while sharks were feeding, accounting for ∼50% of identified items, while copepods (<2 mm) dominated background samples. The size structure was skewed towards larger animals representative of L.hanseni in feeding samples. Thus, whale sharks at Mafia Island target patches of dense, large, zooplankton dominated by sergestids. Large planktivores, such as whale sharks, which generally inhabit warm oligotrophic waters, aggregate in areas where they can feed on dense prey to obtain sufficient energy. PMID:25814777

Colateralization of Broca's Area and the Visual Word form Area in Left-Handers: fMRI Evidence

ERIC Educational Resources Information Center

Van der Haegen, Lise; Cai, Qing; Brysbaert, Marc

2012-01-01

Language production has been found to be lateralized in the left hemisphere (LH) for 95% of right-handed people and about 75% of left-handers. The prevalence of atypical right hemispheric (RH) or bilateral lateralization for reading and colateralization of production with word reading laterality has never been tested in a large sample. In this…

Assessing change in large-scale forest area by visually interpreting Landsat images

Treesearch

Jerry D. Greer; Frederick P. Weber; Raymond L. Czaplewski

2000-01-01

As part of the Forest Resources Assessment 1990, the Food and Agriculture Organization of the United Nations visually interpreted a stratified random sample of 117 Landsat scenes to estimate global status and change in tropical forest area. Images from 1980 and 1990 were interpreted by a group of widely experienced technical people in many different tropical countries...

Projection x-ray topography system at 1-BM x-ray optics test beamline at the advanced photon source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stoupin, Stanislav, E-mail: sstoupin@aps.anl.gov; Liu, Zunping; Trakhtenberg, Emil

2016-07-27

Projection X-ray topography of single crystals is a classic technique for the evaluation of intrinsic crystal quality of large crystals. In this technique a crystal sample and an area detector (e.g., X-ray film) collecting intensity of a chosen crystallographic reflection are translated simultaneously across an X-ray beam collimated in the diffraction scattering plane (e.g., [1, 2]). A bending magnet beamline of a third-generation synchrotron source delivering x-ray beam with a large horizontal divergence, and therefore, a large horizontal beam size at a crystal sample position offers an opportunity to obtain X-ray topographs of large crystalline samples (e.g., 6-inch wafers) inmore » just a few exposures. Here we report projection X-ray topography system implemented recently at 1-BM beamline of the Advanced Photon Source. A selected X-ray topograph of a 6-inch wafer of 4H-SiC illustrates capabilities and limitations of the technique.« less

Quality control of measurements made on fixed-area sample plots

Treesearch

Ola Lindgren

2000-01-01

The paper describes results from a large program for quality control of forest measurements. The performance of 87 surveyors was evaluated. Tree heights were usually measured well, whereas the counting of tree-rings on increment cores was a source of considerable bias for many surveyors. During tree count on sample plots, many surveyors had a tendency to forget trees,...

Quantitative Analysis of Defects in Silicon. Silicon Sheet Growth Development for the Large Area Silicon Sheet Task of the Low-cost Solar Array Project

NASA Technical Reports Server (NTRS)

Natesh, R.; Smith, J. M.; Qidwai, H. A.

1979-01-01

The various steps involved in the chemical polishing and etching of silicon samples are described. Data on twins, dislocation pits, and grain boundaries from thirty-one (31) silicon sample are also discussed. A brief review of the changes made to upgrade the image analysis system is included.

X-ray micro-CT and neutron CT as complementary imaging tools for non-destructive 3D imaging of rare silicified fossil plants

NASA Astrophysics Data System (ADS)

Karch, J.; Dudák, J.; Žemlička, J.; Vavřík, D.; Kumpová, I.; Kvaček, J.; Heřmanová, Z.; Šoltés, J.; Viererbl, L.; Morgano, M.; Kaestner, A.; Trtík, P.

2017-12-01

Computed tomography provides 3D information of inner structures of investigated objects. The obtained information is, however, strongly dependent on the used radiation type. It is known that as X-rays interact with electron cloud and neutrons with atomic nucleus, the obtained data often provide different contrast of sample structures. In this work we present a set of comparative radiographic and CT measurements of rare fossil plant samples using X-rays and thermal neutrons. The X-ray measurements were performed using large area photon counting detectors Timepix at IEAP CTU in Prague and Perkin Elmer flat-panel detector at Center of Excellence Telč. The neutron CT measurement was carried out at Paul Scherrer Institute using BOA beam-line. Furthermore, neutron radiography of fossil samples, provided by National Museum, were performed using a large-area Timepix detector with a neutron-sensitive converting 6LiF layer at Research Centre Rez, Czech Republic. The obtained results show different capabilities of both imaging approaches. While X-ray micro-CT provides very high resolution and enables visualization of fine cracks or small cavities in the samples neutron imaging provides high contrast of morphological structures of fossil plant samples, where X-ray imaging provides insufficient contrast.

Depressive Symptoms of Chinese Children: Prevalence and Correlated Factors among Subgroups.

PubMed

Zhou, Mi; Zhang, Guangsheng; Rozelle, Scott; Kenny, Kaleigh; Xue, Hao

2018-02-07

Economic growth and socioeconomic changes have transformed nearly every aspect of childhood in China, and many are worried by the increasing prevalence of mental health issues among children, particularly depression. To provide insight into the distribution of depressive symptoms among children in China and identify vulnerable groups, we use data from the 2012 China Family Panel Survey (CFPS), a survey that collected data from a large, nationally representative sample of the Chinese population. Using the CFPS data, we construct a sample of 2679 children aged 10-15 years old from 25 provinces in China. According to our results, the incidence of depression varies by geographic area. Specifically, we find that rates of depressive symptoms are significantly lower in urban areas (14% of sample children) than in rural areas (23% of sample children). Our results also show that children from ethnic minorities, from poorer families, and whose parents are depressed are more likely to be depressed than other children. In contrast, we find that depressive symptoms do not vary by gender.

Field-based evaluations of sampling techniques to support long-term monitoring of riparian ecosystems along wadeable streams on the Colorado Plateau

USGS Publications Warehouse

Scott, Michael L.; Reynolds, Elizabeth W.

2007-01-01

Compared to 5-m by 20-m tree quadrats, belt transects were shown to provide similar estimates of stand structure (stem density and stand basal area) in less than 30 percent of the time. Further, for the streams sampled, there were no statistically significant differences in stem density and basal area estimates between 10-m and 20-m belt transects and the smaller belts took approximately half the time to sample. There was, however, high variance associated with estimates of stand structure for infrequently occurring stems, such as large, relict or legacy riparian trees. Legacy riparian trees occurred in limited numbers at all sites sampled. A reachscale population census of these trees indicated that the 10-m belt transects tended to underestimate both stem density and basal area for these riparian forest elements and that a complete reach-scale census of legacy trees averaged less than one hour per site.

Speciation of arsenic, selenium, and chromium in wildfire impacted soils and ashes

USGS Publications Warehouse

Wolf, Ruth E.; Hoefen, Todd M.; Hageman, Philip L.; Morman, Suzette A.; Plumlee, Geoffrey S.

2010-01-01

In 2007-09, California experienced several large wildfires that damaged large areas of forest and destroyed many homes and buildings. The U.S. Geological Survey collected samples from the Harris, Witch, Grass Valley, Ammo, Santiago, Canyon, Jesusita, and Station fires for testing to identify any possible characteristics of the ashes and soils from burned areas that may be of concern for their impact on water quality, human health, and endangered species. The samples were subjected to analysis for bulk chemical composition for 44 elements by inductively coupled plasma mass spectrometry (ICP-MS) after acid digestion and de-ionized water leach tests for pH, alkalinity, conductivity, and anions. Water leach tests generated solutions ranging from pH 10-12, suggesting that ashes can generate caustic alkalinity in contact with rainwater or body fluids (for example, sweat and fluids in the respiratory tract). Samples from burned residential areas in the 2007 fires had elevated levels for several metals, including: As, Pb, Sb, Cu, Zn, and Cr. In some cases, the levels found were above the U.S. Environmental Protection Agency (USEPA) preliminary remediation goals (PRG) for soils. Speciation analyses were conducted on de-ionized water and simulated lung fluid leachates for As(III), As(V), Se(IV), Se(VI), Cr(III), and Cr(VI). All species were determined in the same analytical run using an ion-pairing HPLC-ICP-MS method. For leachates containing high levels of total Cr, the majority of the chromium was present in the hexavalent, Cr(VI), form. Higher total and hexavalent chromium levels were observed for samples collected from burned residential areas. Arsenic was also generally present in the more oxidized, As(V), form. Selenium (IV) and (VI) were present, but typically at levels below 2 ppb for most samples. Stability studies of leachate solutions under different storage conditions were performed and the suitability of different sample preservation methods for speciation analysis will be discussed.

Chlorophyll a and inorganic suspended solids in backwaters of the upper Mississippi River system: Backwater lake effects and their associations with selected environmental predictors

USGS Publications Warehouse

Rogala, James T.; Gray, Brian R.

2006-01-01

The Long Term Resource Monitoring Program (LTRMP) uses a stratified random sampling design to obtain water quality statistics within selected study reaches of the Upper Mississippi River System (UMRS). LTRMP sampling strata are based on aquatic area types generally found in large rivers (e.g., main channel, side channel, backwater, and impounded areas). For hydrologically well-mixed strata (i.e., main channel), variance associated with spatial scales smaller than the strata scale is a relatively minor issue for many water quality parameters. However, analysis of LTRMP water quality data has shown that within-strata variability at the strata scale is high in off-channel areas (i.e., backwaters). A portion of that variability may be associated with differences among individual backwater lakes (i.e., small and large backwater regions separated by channels) that cumulatively make up the backwater stratum. The objective of the statistical modeling presented here is to determine if differences among backwater lakes account for a large portion of the variance observed in the backwater stratum for selected parameters. If variance associated with backwater lakes is high, then inclusion of backwater lake effects within statistical models is warranted. Further, lakes themselves may represent natural experimental units where associations of interest to management may be estimated.

The second Southern African Bird Atlas Project: Causes and consequences of geographical sampling bias.

PubMed

Hugo, Sanet; Altwegg, Res

2017-09-01

Using the Southern African Bird Atlas Project (SABAP2) as a case study, we examine the possible determinants of spatial bias in volunteer sampling effort and how well such biased data represent environmental gradients across the area covered by the atlas. For each province in South Africa, we used generalized linear mixed models to determine the combination of variables that explain spatial variation in sampling effort (number of visits per 5' × 5' grid cell, or "pentad"). The explanatory variables were distance to major road and exceptional birding locations or "sampling hubs," percentage cover of protected, urban, and cultivated area, and the climate variables mean annual precipitation, winter temperatures, and summer temperatures. Further, we used the climate variables and plant biomes to define subsets of pentads representing environmental zones across South Africa, Lesotho, and Swaziland. For each environmental zone, we quantified sampling intensity, and we assessed sampling completeness with species accumulation curves fitted to the asymptotic Lomolino model. Sampling effort was highest close to sampling hubs, major roads, urban areas, and protected areas. Cultivated area and the climate variables were less important. Further, environmental zones were not evenly represented by current data and the zones varied in the amount of sampling required representing the species that are present. SABAP2 volunteers' preferences in birding locations cause spatial bias in the dataset that should be taken into account when analyzing these data. Large parts of South Africa remain underrepresented, which may restrict the kind of ecological questions that may be addressed. However, sampling bias may be improved by directing volunteers toward undersampled regions while taking into account volunteer preferences.

Lot quality assurance sampling for monitoring coverage and quality of a targeted condom social marketing programme in traditional and non-traditional outlets in India

PubMed Central

Piot, Bram; Navin, Deepa; Krishnan, Nattu; Bhardwaj, Ashish; Sharma, Vivek; Marjara, Pritpal

2010-01-01

Objectives This study reports on the results of a large-scale targeted condom social marketing campaign in and around areas where female sex workers are present. The paper also describes the method that was used for the routine monitoring of condom availability in these sites. Methods The lot quality assurance sampling (LQAS) method was used for the assessment of the geographical coverage and quality of coverage of condoms in target areas in four states and along selected national highways in India, as part of Avahan, the India AIDS initiative. Results A significant general increase in condom availability was observed in the intervention area between 2005 and 2008. High coverage rates were gradually achieved through an extensive network of pharmacies and particularly of non-traditional outlets, whereas traditional outlets were instrumental in providing large volumes of condoms. Conclusion LQAS is seen as a valuable tool for the routine monitoring of the geographical coverage and of the quality of delivery systems of condoms and of health products and services in general. With a relatively small sample size, easy data collection procedures and simple analytical methods, it was possible to inform decision-makers regularly on progress towards coverage targets. PMID:20167732

Lot quality assurance sampling for monitoring coverage and quality of a targeted condom social marketing programme in traditional and non-traditional outlets in India.

PubMed

Piot, Bram; Mukherjee, Amajit; Navin, Deepa; Krishnan, Nattu; Bhardwaj, Ashish; Sharma, Vivek; Marjara, Pritpal

2010-02-01

This study reports on the results of a large-scale targeted condom social marketing campaign in and around areas where female sex workers are present. The paper also describes the method that was used for the routine monitoring of condom availability in these sites. The lot quality assurance sampling (LQAS) method was used for the assessment of the geographical coverage and quality of coverage of condoms in target areas in four states and along selected national highways in India, as part of Avahan, the India AIDS initiative. A significant general increase in condom availability was observed in the intervention area between 2005 and 2008. High coverage rates were gradually achieved through an extensive network of pharmacies and particularly of non-traditional outlets, whereas traditional outlets were instrumental in providing large volumes of condoms. LQAS is seen as a valuable tool for the routine monitoring of the geographical coverage and of the quality of delivery systems of condoms and of health products and services in general. With a relatively small sample size, easy data collection procedures and simple analytical methods, it was possible to inform decision-makers regularly on progress towards coverage targets.

Open-Source Automated Mapping Four-Point Probe.

PubMed

Chandra, Handy; Allen, Spencer W; Oberloier, Shane W; Bihari, Nupur; Gwamuri, Jephias; Pearce, Joshua M

2017-01-26

Scientists have begun using self-replicating rapid prototyper (RepRap) 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP) measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO) samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas.

Handling a Small Dataset Problem in Prediction Model by employ Artificial Data Generation Approach: A Review

NASA Astrophysics Data System (ADS)

Lateh, Masitah Abdul; Kamilah Muda, Azah; Yusof, Zeratul Izzah Mohd; Azilah Muda, Noor; Sanusi Azmi, Mohd

2017-09-01

The emerging era of big data for past few years has led to large and complex data which needed faster and better decision making. However, the small dataset problems still arise in a certain area which causes analysis and decision are hard to make. In order to build a prediction model, a large sample is required as a training sample of the model. Small dataset is insufficient to produce an accurate prediction model. This paper will review an artificial data generation approach as one of the solution to solve the small dataset problem.

Case history of population change in a `bacillus thuringiensis`-treated versus an untreated outbreak of the western spruce budworm. Forest Service research note

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mason, R.R.; Paul, H.G.

1996-09-01

Larval densities of the western spruce budworm (Choristoneura occidentalis Freeman) were monitored for 12 years (1984-95) on permanent sample plots in northeastern Oregon. The time series spanned a period of general budworm infestations when populations increased rapidly from low densities, plateaued for a time at high-outbreak densities, and then declind suddenly. Midway through the period (1988), an area with half of the sample plots was sprayed with the microbial insecticide Bacillus thuringiensis (B.t.) in an operational suppression project. The other sample plots were part of an untreated area. In the treated area, B.t. spray reduced numbers of larvae by moremore » than 90 percent; however, populations returned to an outbreak density within 3 years. In the untreated area, populations remained at outbreak densities and continued to fluctuate due to natural feedback processes. Natural decline of the population (1992-95) in the monitored area was largely unexplained and coincided with an overall collapse of the budworm outbreak in the Blue Mountains.« less

An ecological assessment of a bridge demolition.

DOT National Transportation Integrated Search

1975-01-01

Bridge demolition has long been known to mobilize large amounts of stream sediment in the immediate area of the structure. An ecological assessment in terms of stream macroinvertebrate samples and suspended solids measurements was made shortly before...

Synergistic interactions between edge and area effects in a heavily fragmented landscape.

PubMed

Ewers, Robert M; Thorpe, Stephen; Didham, Raphael K

2007-01-01

Both area and edge effects have a strong influence on ecological processes in fragmented landscapes, but there is little understanding of how these two factors might interact to exacerbate local species declines. To test for synergistic interactions between area and edge effects, we sampled a diverse beetle community in a heavily fragmented landscape in New Zealand. More than 35,000 beetles of approximately 900 species were sampled over large gradients in habitat area (10(-2) 10(6) ha) and distance from patch edge (2(0)-2(10) m from the forest edge into both the forest and adjacent matrix). Using a new approach to partition variance following an ordination analysis, we found that a synergistic interaction between habitat area and distance to edge was a more important determinant of patterns in beetle community composition than direct edge or area effects alone. The strength of edge effects in beetle-species composition increased nonlinearly with increasing fragment area. One important consequence of the synergy is that the slopes of species area (SA) curves constructed from habitat islands depend sensitively on the distance from edge at which sampling is conducted. Surprisingly, we found negative SA curves for communities sampled at intermediate distances from habitat edges, caused by differential edge responses of matrix- vs. forest-specialist species in fragments of increasing area. Our data indicate that distance to habitat edge has a consistently greater impact on beetle community composition than habitat area and that variation in the strength of edge effects may underlie many patterns that are superficially related to habitat area.

Wipe-rinse technique for quantitating microbial contamination on large surfaces.

PubMed Central

Kirschner, L E; Puleo, J R

1979-01-01

The evaluation of an improved wipe-rinse technique for the bioassay of large areas was undertaken due to inherent inadequacies in the cotton swab-rinse technique to which assay of spacecraft is currently restricted. Four types of contamination control cloths were initially tested. A polyester-bonded cloth (PBC) was selected for further evaluation because of its superior efficiency and handling characteristics. Results from comparative tests with PBC and cotton swabs on simulated spacecraft surfaces indicated a significantly higher recovery efficiency for the PBC than for the cotton (90.4 versus 75.2%). Of the sampling areas sites studied, PBC was found to be most effective on surface areas not exceeding 0.74 m2 (8.0 feet 2). PMID:394682

Wipe-rinse technique for quantitating microbial contamination on large surfaces

NASA Technical Reports Server (NTRS)

Kirschner, L. E.; Puleo, J. R.

1979-01-01

The evaluation of an improved wipe-rinse technique for the bioassay of large areas was undertaken due to inherent inadequacies in the cotton swab-rinse technique to which assay of spacecraft is currently restricted. Four types of contamination control cloths were initially tested. A polyester-bonded cloth (PBC) was selected for further evaluation because of its superior efficiency and handling characteristics. Results from comparative tests with PBC and cotton swabs on simulated spacecraft surfaces indicated a significantly higher recovery efficiency for the PBC than for the cotton (90.4 versus 75.2%). Of the sampling area sites studied, PBC was found to be most effective on surface areas not exceeding 0.74 sq m (8.0 sq ft).

Medium- and large-sized mammals in a steppic savanna area of the Brazilian Pampa: survey and conservation issues of a poorly known fauna.

PubMed

Espinosa, C C; Galiano, D; Kubiak, B B; Marinho, J R

2016-02-01

The wildlife of the Brazilian Pampa is threatened by large-scale habitat loss, due in particular to the expansion of soybean cultivation and the conversion of grasslands areas into extensive areas of silviculture. It is essential to study how the mammal fauna copes with the highly fragmented, human-influenced, non-protected landscape. Our study presents the results of a survey of the large- and medium-sized mammals of a typical human-influenced steppic savanna area of the Pampa biome. The survey was conducted exclusively with the use of camera traps over a period of 16 months. The relative frequencies of species in the area were evaluated. We recorded 18 species, some of them locally threatened (Tamandua tetradactyla, Alouatta caraya, Leopardus colocolo, Leopardus geoffroyi, Leopardus wiedii, Puma yagouaroundi, Mazama gouazoubira and Cuniculus paca). Several species were found to thrive in the area; however, many species were considered rare, and undoubtedly new species could be recorded if we continued the sampling. Our results contribute to the knowledge of faunal diversity in the Pampa biome and associated habitats, warn about threats and provide support for conservation measures.

Synthesis of polybenzoxazine based nitrogen-rich porous carbons for carbon dioxide capture

NASA Astrophysics Data System (ADS)

Wan, Liu; Wang, Jianlong; Feng, Chong; Sun, Yahui; Li, Kaixi

2015-04-01

Nitrogen-rich porous carbons (NPCs) were synthesized from 1,5-dihydroxynaphthalene, urea, and formaldehyde based on benzoxazine chemistry by a soft-templating method with KOH chemical activation. They possess high surface areas of 856.8-1257.8 m2 g-1, a large pore volume of 0.15-0.65 cm3 g-1, tunable pore structure, high nitrogen content (5.21-5.32 wt%), and high char yields. The amount of the soft-templating agent F127 has multiple influences on the textural and chemical properties of the carbons, affecting the surface area and pore structure, impacting the compositions of nitrogen species and resulting in an improvement of the CO2 capture performance. At 1 bar, high CO2 uptake of 4.02 and 6.35 mmol g-1 at 25 and 0 °C was achieved for the sample NPC-2 with a molar ratio of F127 : urea = 0.010 : 1. This can be attributed to its well-developed micropore structure and abundant pyridinic nitrogen, pyrrolic nitrogen and pyridonic nitrogen functionalities. The sample NPC-2 also exhibits a remarkable selectivity for CO2/N2 separation and a fast adsorption/desorption rate and can be easily regenerated. This suggests that the polybenzoxazine-based NPCs are desirable for CO2 capture because of possessing a high micropore surface area, a large micropore volume, appropriate pore size distribution, and a large number of basic nitrogen functionalities.Nitrogen-rich porous carbons (NPCs) were synthesized from 1,5-dihydroxynaphthalene, urea, and formaldehyde based on benzoxazine chemistry by a soft-templating method with KOH chemical activation. They possess high surface areas of 856.8-1257.8 m2 g-1, a large pore volume of 0.15-0.65 cm3 g-1, tunable pore structure, high nitrogen content (5.21-5.32 wt%), and high char yields. The amount of the soft-templating agent F127 has multiple influences on the textural and chemical properties of the carbons, affecting the surface area and pore structure, impacting the compositions of nitrogen species and resulting in an improvement of the CO2 capture performance. At 1 bar, high CO2 uptake of 4.02 and 6.35 mmol g-1 at 25 and 0 °C was achieved for the sample NPC-2 with a molar ratio of F127 : urea = 0.010 : 1. This can be attributed to its well-developed micropore structure and abundant pyridinic nitrogen, pyrrolic nitrogen and pyridonic nitrogen functionalities. The sample NPC-2 also exhibits a remarkable selectivity for CO2/N2 separation and a fast adsorption/desorption rate and can be easily regenerated. This suggests that the polybenzoxazine-based NPCs are desirable for CO2 capture because of possessing a high micropore surface area, a large micropore volume, appropriate pore size distribution, and a large number of basic nitrogen functionalities. Electronic supplementary information (ESI) available: Elemental and XPS analyses and XPS peak positions and relative content of N species in the NPCs. See DOI: 10.1039/c4nr07409b

Measurement of Tritium in Gas Phase Soil Moisture and Helium-3 in Soil Gas at the Hanford Townsite and 100 K Area

DOE Office of Scientific and Technical Information (OSTI.GOV)

KB Olsen; GW Patton; R Poreda

2000-07-05

In 1999, soil gas samples for helium-3 measurements were collected at two locations on the Hanford Site. Eight soil gas sampling points ranging in depth from 1.5 to 9.8 m (4.9 to 32 ft) below ground surface (bgs) in two clusters were installed adjacent to well 699-41-1, south of the Hanford Townsite. Fifteen soil gas sampling points, ranging in depth from 2.1 to 3.2 m (7 to 10.4 ft) bgs, were installed to the north and east of the 100 KE Reactor. Gas phase soil moisture samples were collected using silica gel traps from all eight sampling locations adjacent tomore » well 699-41-1 and eight locations at the 100 K Area. No detectable tritium (<240 pCi/L) was found in the soil moisture samples from either the Hanford Townsite or 100 K Area sampling points. This suggests that tritiated moisture from groundwater is not migrating upward to the sampling points and there are no large vadose zone sources of tritium at either location. Helium-3 analyses of the soil gas samples showed significant enrichments relative to ambient air helium-3 concentrations with a depth dependence consistent with a groundwater source from decay of tritium. Helium-3/helium-4 ratios (normalized to the abundances in ambient air) at the Hanford Townsite ranged from 1.012 at 1.5 m (5 ft) bgs to 2.157 at 9.8 m (32 ft) bgs. Helium-3/helium-4 ratios at the 100 K Area ranged from 0.972 to 1.131. Based on results from the 100 K Area, the authors believe that a major tritium plume does not lie within that study area. The data also suggest there may be a tritium groundwater plume or a source of helium-3 to the southeast of the study area. They recommend that the study be continued by placing additional soil gas sampling points along the perimeter road to the west and to the south of the initial study area.« less

Cosmological constraints from X-ray all sky surveys, from CODEX to eROSITA

NASA Astrophysics Data System (ADS)

Finoguenov, A.

2017-10-01

Large area cluster cosmology has long become a multiwavelength discipline. Understanding the effect of various selections is currently the main path to improving on the validity of cluster cosmological results. Many of these results are based on the large area sample derived from RASS data. We perform wavelet detection of X-ray sources and make extensive simulations of the detection of clusters in the RASS data. We assign an optical richness to each of the 25,000 detected X-ray sources in the 10,000 square degrees of SDSS BOSS area. We show that there is no obvious separation of sources on galaxy clusters and AGN, based on distribution of systems on their richness. We conclude that previous catalogs, such as MACS, REFLEX are all subject to a complex optical selection function, in addition to an X-ray selection. We provide a complete model of identification of cluster counts are galaxy clusters, which includes chance identification, effect of AGN halo occupation distribution and the thermal emission of ICM. Finally we present the cosmological results obtained using this sample.

Eco-friendly materials for large area piezoelectronics: self-oriented Rochelle salt in wood

NASA Astrophysics Data System (ADS)

Lemaire, E.; Ayela, C.; Atli, A.

2018-02-01

Upgraded biodegradable piezoelectric composite materials elaborated by incorporation of Rochelle salt (RS, Sodium potassium tartrate tetrahydrate) in wood were reported. RS crystals, known as the first discovered piezoelectric material, were grown in the micro-cavities of wood, having naturally a tubular structure, by soaking the wood into RS saturated water. Since most of the cavities in wood are oriented in the same direction, the piezoelectric effect was improved when the cavities were filled by RS crystals. The mechanical, structural and piezoelectric properties of RS incorporated wood composite samples were characterized. Both direct and converse piezoelectric effects are illustrated. The wood-base composite exhibits an effective piezoelectric constant d 33 of 11 pC N-1. Also, the flexural strength and modulus of elasticity were enhanced by inserting RS into the wood, nevertheless the samples became more brittle. The wood-based piezoelectric samples prepared in this work can be used as actuators, sensors or energy harvesters. The process developed here permits us to manufacture large area piezoelectric devices which are environmentally and economically unsurpassed.

Distribution of gold, tellurium, silver, and mercury in part of the Cripple Creek district, Colorado

USGS Publications Warehouse

Gott, Garland Bayard; McCarthy, J.H.; Van Sickle, G.H.; McHugh, J.B.

1967-01-01

Geochemical exploration studies were undertaken in the Cripple Creek district to test the possibility that large low-grade gold deposits might be found. Surface rock samples taken throughout the district indicate that the volcanic rocks between the productive veins contain an average of about 0.6 ppm (part per million) gold. In an area above 3,800 feet long and 500 feet wide near the Cresson mine in the south-central part of the district, scattered surface samples show that the rocks contain an average of 2.5 ppm gold, equivalent to $2.50 per ton. Inasmuch as veins that contain more than 2.5 ppm may also exist in the area, systematic sampling by trenching and drilling is warranted.

The effects of urbanization on population density, occupancy, and detection probability of wild felids.

PubMed

Lewis, Jesse S; Logan, Kenneth A; Alldredge, Mat W; Bailey, Larissa L; VandeWoude, Sue; Crooks, Kevin R

2015-10-01

Urbanization is a primary driver of landscape conversion, with far-reaching effects on landscape pattern and process, particularly related to the population characteristics of animals. Urbanization can alter animal movement and habitat quality, both of which can influence population abundance and persistence. We evaluated three important population characteristics (population density, site occupancy, and species detection probability) of a medium-sized and a large carnivore across varying levels of urbanization. Specifically, we studied bobcat and puma populations across wildland, exurban development, and wildland-urban interface (WUI) sampling grids to test hypotheses evaluating how urbanization affects wild felid populations and their prey. Exurban development appeared to have a greater impact on felid populations than did habitat adjacent to a major urban area (i.e., WUI); estimates of population density for both bobcats and pumas were lower in areas of exurban development compared to wildland areas, whereas population density was similar between WUI and wildland habitat. Bobcats and pumas were less likely to be detected in habitat as the amount of human disturbance associated with residential development increased at a site, which was potentially related to reduced habitat quality resulting from urbanization. However, occupancy of both felids was similar between grids in both study areas, indicating that this population metric was less sensitive than density. At the scale of the sampling grid, detection probability for bobcats in urbanized habitat was greater than in wildland areas, potentially due to restrictive movement corridors and funneling of animal movements in landscapes influenced by urbanization. Occupancy of important felid prey (cottontail rabbits and mule deer) was similar across levels of urbanization, although elk occupancy was lower in urbanized areas. Our study indicates that the conservation of medium- and large-sized felids associated with urbanization likely will be most successful if large areas of wildland habitat are maintained, even in close proximity to urban areas, and wildland habitat is not converted to low-density residential development.

Large-Scale Optimization for Bayesian Inference in Complex Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Willcox, Karen; Marzouk, Youssef

2013-11-12

The SAGUARO (Scalable Algorithms for Groundwater Uncertainty Analysis and Robust Optimization) Project focused on the development of scalable numerical algorithms for large-scale Bayesian inversion in complex systems that capitalize on advances in large-scale simulation-based optimization and inversion methods. The project was a collaborative effort among MIT, the University of Texas at Austin, Georgia Institute of Technology, and Sandia National Laboratories. The research was directed in three complementary areas: efficient approximations of the Hessian operator, reductions in complexity of forward simulations via stochastic spectral approximations and model reduction, and employing large-scale optimization concepts to accelerate sampling. The MIT--Sandia component of themore » SAGUARO Project addressed the intractability of conventional sampling methods for large-scale statistical inverse problems by devising reduced-order models that are faithful to the full-order model over a wide range of parameter values; sampling then employs the reduced model rather than the full model, resulting in very large computational savings. Results indicate little effect on the computed posterior distribution. On the other hand, in the Texas--Georgia Tech component of the project, we retain the full-order model, but exploit inverse problem structure (adjoint-based gradients and partial Hessian information of the parameter-to-observation map) to implicitly extract lower dimensional information on the posterior distribution; this greatly speeds up sampling methods, so that fewer sampling points are needed. We can think of these two approaches as ``reduce then sample'' and ``sample then reduce.'' In fact, these two approaches are complementary, and can be used in conjunction with each other. Moreover, they both exploit deterministic inverse problem structure, in the form of adjoint-based gradient and Hessian information of the underlying parameter-to-observation map, to achieve their speedups.« less

Final Report: Large-Scale Optimization for Bayesian Inference in Complex Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghattas, Omar

2013-10-15

The SAGUARO (Scalable Algorithms for Groundwater Uncertainty Analysis and Robust Optimiza- tion) Project focuses on the development of scalable numerical algorithms for large-scale Bayesian inversion in complex systems that capitalize on advances in large-scale simulation-based optimiza- tion and inversion methods. Our research is directed in three complementary areas: efficient approximations of the Hessian operator, reductions in complexity of forward simulations via stochastic spectral approximations and model reduction, and employing large-scale optimization concepts to accelerate sampling. Our efforts are integrated in the context of a challenging testbed problem that considers subsurface reacting flow and transport. The MIT component of the SAGUAROmore » Project addresses the intractability of conventional sampling methods for large-scale statistical inverse problems by devising reduced-order models that are faithful to the full-order model over a wide range of parameter values; sampling then employs the reduced model rather than the full model, resulting in very large computational savings. Results indicate little effect on the computed posterior distribution. On the other hand, in the Texas-Georgia Tech component of the project, we retain the full-order model, but exploit inverse problem structure (adjoint-based gradients and partial Hessian information of the parameter-to- observation map) to implicitly extract lower dimensional information on the posterior distribution; this greatly speeds up sampling methods, so that fewer sampling points are needed. We can think of these two approaches as "reduce then sample" and "sample then reduce." In fact, these two approaches are complementary, and can be used in conjunction with each other. Moreover, they both exploit deterministic inverse problem structure, in the form of adjoint-based gradient and Hessian information of the underlying parameter-to-observation map, to achieve their speedups.« less

Reconnaissance geochemical survey of the Farah Garan-Kutam mineral belt, Kingdom of Saudi Arabia

USGS Publications Warehouse

Samater, R.M.; Johnson, P.R.; Bookstrom, A.A.

1991-01-01

In the present survey, geochemical anomalies locate all the sites of mineralization known from previous work. The survey is therefore technically a success. However, a large number of these anomalies probably result from contamination of the wadi systems by metal dispersed from ancient mine workings, and this particular survey, overall, may be of limited value as a guide to the discovery of hitherto unknown mineralization. Nevertheless, the survey outlines two areas that may mark extensions to known mineralization, and a number of other areas in which no mineralization is known. Based on a consideration of the character of the bedrock geology, the value of each reported analytical result in relation to the respective element thresholds, and the number of anomalous samples that cluster in any given area, four areas are recommended for high-priority follow-up sampling.

The susceptibility of large river basins to orogenic and climatic drivers

NASA Astrophysics Data System (ADS)

Haedke, Hanna; Wittmann, Hella; von Blanckenburg, Friedhelm

2017-04-01

Large rivers are known to buffer pulses in sediment production driven by changes in climate as sediment is transported through lowlands. Our new dataset of in situ cosmogenic nuclide concentration and chemical composition of 62 sandy bedload samples from the world largest rivers integrates over 25% of Earth's terrestrial surface, distributed over a variety of climatic zones across all continents, and represents the millennial-scale denudation rate of the sediment's source area. We can show that these denudation rates do not respond to climatic forcing, but faithfully record orogenic forcing, when analyzed with respective variables representing orogeny (strain rate, relief, bouguer anomaly, free-air anomaly), and climate (runoff, temperature, precipitation) and basin properties (floodplain response time, drainage area). In contrast to this orogenic forcing of denudation rates, elemental bedload chemistry from the fine-grained portion of the same samples correlates with climate-related variables (precipitation, runoff) and floodplain response times. It is also well-known from previous compilations of river-gauged sediment loads that the short-term basin-integrated sediment export is also climatically controlled. The chemical composition of detrital sediment shows a climate control that can originate in the rivers source area, but this signal is likely overprinted during transfer through the lowlands because we also find correlation with floodplain response times. At the same time, cosmogenic nuclides robustly preserve the orogenic forcing of the source area denudation signal through of the floodplain buffer. Conversely, previous global compilations of cosmogenic nuclides in small river basins show the preservation of climate drivers in their analysis, but these are buffered in large lowland rivers. Hence, we can confirm the assumption that cosmogenic nuclides in large rivers are poorly susceptible to climate changes, but are at the same time highly suited to detect changes in orogenic forcing in their paleo sedimentary records.

Potential sources of bacteriological pollution for two bays with marinas in Trinidad.

PubMed

Bullock, Christine Ann; Moonesar, Indar

2005-05-01

Welcome Bay and Chaguaramas Bay in the northwest peninsula of Trinidad contain large marinas and smaller sections of bathing beaches. Bacteriological surveys were conducted at both bays to assess water quality and to determine potential sources of pollution. These surveys were conducted during the wet season of 1996 and the dry season of 1997. Eleven sample stations were established at Welcome Bay and 12 at Chaguaramas Bay. Freshwater samples were collected from rivers and drains within the survey area. Marine water samples were collected from marinas, bathing beaches and inshore and outer areas at both bays. Five water samples were collected from each sampling station during the wet season of 1996 and six during the dry season of 1997. The membrane filter technique was used to determine faecal coliform and Escherichia coli levels in all samples. There was a seasonal effect on water quality, with significantly higher faecal coliform levels in the wet season, when water quality was not in compliance with international standards. This represents a potential health risk in bathing areas. Water quality was better at the outer area of both bays. Water quality at the inner bay areas was most likely adversely affected by land-based sources of pollution identified in this study. These sources include three drains and two rivers, which discharged into the bays. Yachts were apparently not a source of sewage pollution: there was no significant relationship between yacht number and faecal coliform levels.

Assessing insect-induced tree mortality across large areas with high-resolution aerial photography in a multistage sample

Treesearch

Randy Hamilton; Kevin Megown; James Ellenwood; Henry Lachowski; Paul Maus

2010-01-01

In recent years, unprecedented tree mortality has occurred throughout the national forests owing to insect infestations and disease outbreaks. The magnitude and extent of mortality, coupled with the lack of routine monitoring in some areas, has made it difficult to assess the damage, associated ecological impact, and fire hazard in a timely and cost-effective manner....

Procedures to handle inventory cluster plots that straddle two or more conditions

Treesearch

Jerold T. Hahn; Colin D. MacLean; Stanford L. Arner; William A. Bechtold

1995-01-01

We review the relative merits and field procedures for four basic plot designs to handle forest inventory plots that straddle two or more conditions, given that subplots will not be moved. A cluster design is recommended that combines fixed-area subplots and variable-radius plot (VRP) sampling. Each subplot in a cluster consists of a large fixed-area subplot for...

Ground-water quality in selected areas of Wisconsin

USGS Publications Warehouse

Hindall, S.M.

1979-01-01

Analysis of 2,071 ground-water samples from 970 wells throughout Wisconsin indicate large variations in ground-water quality. Ground water in Wisconsin is generally suitable for most uses, but in some areas concentrations of chemical constituents exceed recommended drinking-water standards. Iron, manganese, and nitrate commonly exceed recommended drinking-water standards and dissolved solids, sulfate, heavy metals, and phenolic materials may present local problems. (USGS)

Statistical theory and methodology for remote sensing data analysis

NASA Technical Reports Server (NTRS)

Odell, P. L.

1974-01-01

A model is developed for the evaluation of acreages (proportions) of different crop-types over a geographical area using a classification approach and methods for estimating the crop acreages are given. In estimating the acreages of a specific croptype such as wheat, it is suggested to treat the problem as a two-crop problem: wheat vs. nonwheat, since this simplifies the estimation problem considerably. The error analysis and the sample size problem is investigated for the two-crop approach. Certain numerical results for sample sizes are given for a JSC-ERTS-1 data example on wheat identification performance in Hill County, Montana and Burke County, North Dakota. Lastly, for a large area crop acreages inventory a sampling scheme is suggested for acquiring sample data and the problem of crop acreage estimation and the error analysis is discussed.

BOREAS TE-2 NSA Soil Lab Data

NASA Technical Reports Server (NTRS)

Veldhuis, Hugo; Hall, Forrest G. (Editor); Knapp, David E. (Editor)

2000-01-01

This data set contains the major soil properties of soil samples collected in 1994 at the tower flux sites in the Northern Study Area (NSA). The soil samples were collected by Hugo Veldhuis and his staff from the University of Manitoba. The mineral soil samples were largely analyzed by Barry Goetz, under the supervision of Dr. Harold Rostad at the University of Saskatchewan. The organic soil samples were largely analyzed by Peter Haluschak, under the supervision of Hugo Veldhuis at the Centre for Land and Biological Resources Research in Winnipeg, Manitoba. During the course of field investigation and mapping, selected surface and subsurface soil samples were collected for laboratory analysis. These samples were used as benchmark references for specific soil attributes in general soil characterization. Detailed soil sampling, description, and laboratory analysis were performed on selected modal soils to provide examples of common soil physical and chemical characteristics in the study area. The soil properties that were determined include soil horizon; dry soil color; pH; bulk density; total, organic, and inorganic carbon; electric conductivity; cation exchange capacity; exchangeable sodium, potassium, calcium, magnesium, and hydrogen; water content at 0.01, 0.033, and 1.5 MPascals; nitrogen; phosphorus: particle size distribution; texture; pH of the mineral soil and of the organic soil; extractable acid; and sulfur. These data are stored in ASCII text files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

Spatial considerations during cryopreservation of a large volume sample.

PubMed

Kilbride, Peter; Lamb, Stephen; Milne, Stuart; Gibbons, Stephanie; Erro, Eloy; Bundy, James; Selden, Clare; Fuller, Barry; Morris, John

2016-08-01

There have been relatively few studies on the implications of the physical conditions experienced by cells during large volume (litres) cryopreservation - most studies have focused on the problem of cryopreservation of smaller volumes, typically up to 2 ml. This study explores the effects of ice growth by progressive solidification, generally seen during larger scale cryopreservation, on encapsulated liver hepatocyte spheroids, and it develops a method to reliably sample different regions across the frozen cores of samples experiencing progressive solidification. These issues are examined in the context of a Bioartificial Liver Device which requires cryopreservation of a 2 L volume in a strict cylindrical geometry for optimal clinical delivery. Progressive solidification cannot be avoided in this arrangement. In such a system optimal cryoprotectant concentrations and cooling rates are known. However, applying these parameters to a large volume is challenging due to the thermal mass and subsequent thermal lag. The specific impact of this to the cryopreservation outcome is required. Under conditions of progressive solidification, the spatial location of Encapsulated Liver Spheroids had a strong impact on post-thaw recovery. Cells in areas first and last to solidify demonstrated significantly impaired post-thaw function, whereas areas solidifying through the majority of the process exhibited higher post-thaw outcome. It was also found that samples where the ice thawed more rapidly had greater post-thaw viability 24 h post-thaw (75.7 ± 3.9% and 62.0 ± 7.2% respectively). These findings have implications for the cryopreservation of large volumes with a rigid shape and for the cryopreservation of a Bioartificial Liver Device. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Use of space-filling curves to select sample locations in natural resource monitoring studies

Treesearch

Andrew Lister; Charles T. Scott

2009-01-01

The establishment of several large area monitoring networks over the past few decades has led to increased research into ways to spatially balance sample locations across the landscape. Many of these methods are well documented and have been used in the past with great success. In this paper, we present a method using geographic information systems (GIS) and fractals...

Electrocatalytically Active Nickel-Based Electrode Coatings Formed by Atmospheric and Suspension Plasma Spraying

NASA Astrophysics Data System (ADS)

Aghasibeig, M.; Mousavi, M.; Ben Ettouill, F.; Moreau, C.; Wuthrich, R.; Dolatabadi, A.

2014-01-01

Ni-based electrode coatings with enhanced surface areas, for hydrogen production, were developed using atmospheric plasma spray (APS) and suspension plasma spray (SPS) processes. The results revealed a larger electrochemical active surface area for the coatings produced by SPS compared to those produced by APS process. SEM micrographs showed that the surface microstructure of the sample with the largest surface area was composed of a large number of small cauliflower-like aggregates with an average diameter of 10 μm.

New mapping near Iron Creek, Talkeetna Mountains, indicates presence of Nikolai greenstone

USGS Publications Warehouse

Schmidt, Jeanine M.; Werdon, Melanie B.; Wardlaw, Bruce R.

2003-01-01

Detailed geologic mapping in the Iron Creek area, Talkeetna Mountains B-5 Quadrangle, has documented several intrusive bodies and rock units not previously recognized and has extended the geologic history of the area through the Mesozoic and into the Tertiary era. Greenschist-facies metabasalt and metagabbro previously thought to be Paleozoic are intruded by Late Cretaceous to Paleocene dioritic to granitic plutons. The metabasalts are massive to amygdaloidal, commonly contain abundant magnetite, and large areas are patchily altered to epidote ± quartz. They host numerous copper oxide–copper sulfide–quartz–hematite veins and amygdule fillings. These lithologic features, recognized in the field, suggested a correlation of the metamafic rocks with the Late Triassic Nikolai Greenstone, which had not previously been mapped in the Iron Creek area. Thin, discontinuous metalimestones that overlie the metabasalt sequence had previously been assigned a Pennsylvanian(?) and Early Permian age on the basis of correlation with marbles to the north, which yielded Late Paleozoic or Permian macrofossils, or both. Three new samples from the metalimestones near Iron Creek yielded Late Triassic conodonts, which confirms the correlation of the underlying metamafic rocks with Nikolai Greenstone. These new data extend the occurrence of Nikolai Greenstone about 70 km southwest of its previously mapped extent.Five to 10 km north of the conodont sample localities, numerous microgabbro and diabase sills intrude siliceous and locally calcareous metasedimentary rocks of uncertain age. These sills probably represent feeder zones to the Nikolai Greenstone. In the Mt. Hayes quadrangle 150 km to the northeast, large sill-form mafic and ultramafic feeders (for example, the Fish Lake complex) to the Nikolai Greenstone in the Amphitheatre Mountains host magmatic sulfide nickel–copper–platinum-group-element (PGE) mineralization. This new recognition of Nikolai Greenstone and possible magmatic feeders in the Iron Creek area suggests a much greater potential for large PGE, copper, or nickel deposits in the Talkeetna Mountains than previous mineral resource appraisals of the area have suggested, and requires reevaluation of large-scale tectonic models for the area.

Diagnosing and Correcting Mass Accuracy and Signal Intensity Error Due to Initial Ion Position Variations in a MALDI TOFMS

NASA Astrophysics Data System (ADS)

Malys, Brian J.; Piotrowski, Michelle L.; Owens, Kevin G.

2018-02-01

Frustrated by worse than expected error for both peak area and time-of-flight (TOF) in matrix assisted laser desorption ionization (MALDI) experiments using samples prepared by electrospray deposition, it was finally determined that there was a correlation between sample location on the target plate and the measured TOF/peak area. Variations in both TOF and peak area were found to be due to small differences in the initial position of ions formed in the source region of the TOF mass spectrometer. These differences arise largely from misalignment of the instrument sample stage, with a smaller contribution arising from the non-ideal shape of the target plates used. By physically measuring the target plates used and comparing TOF data collected from three different instruments, an estimate of the magnitude and direction of the sample stage misalignment was determined for each of the instruments. A correction method was developed to correct the TOFs and peak areas obtained for a given combination of target plate and instrument. Two correction factors are determined, one by initially collecting spectra from each sample position used and another by using spectra from a single position for each set of samples on a target plate. For TOF and mass values, use of the correction factor reduced the error by a factor of 4, with the relative standard deviation (RSD) of the corrected masses being reduced to 12-24 ppm. For the peak areas, the RSD was reduced from 28% to 16% for samples deposited twice onto two target plates over two days.

Diagnosing and Correcting Mass Accuracy and Signal Intensity Error Due to Initial Ion Position Variations in a MALDI TOFMS

NASA Astrophysics Data System (ADS)

Malys, Brian J.; Piotrowski, Michelle L.; Owens, Kevin G.

2017-12-01

Frustrated by worse than expected error for both peak area and time-of-flight (TOF) in matrix assisted laser desorption ionization (MALDI) experiments using samples prepared by electrospray deposition, it was finally determined that there was a correlation between sample location on the target plate and the measured TOF/peak area. Variations in both TOF and peak area were found to be due to small differences in the initial position of ions formed in the source region of the TOF mass spectrometer. These differences arise largely from misalignment of the instrument sample stage, with a smaller contribution arising from the non-ideal shape of the target plates used. By physically measuring the target plates used and comparing TOF data collected from three different instruments, an estimate of the magnitude and direction of the sample stage misalignment was determined for each of the instruments. A correction method was developed to correct the TOFs and peak areas obtained for a given combination of target plate and instrument. Two correction factors are determined, one by initially collecting spectra from each sample position used and another by using spectra from a single position for each set of samples on a target plate. For TOF and mass values, use of the correction factor reduced the error by a factor of 4, with the relative standard deviation (RSD) of the corrected masses being reduced to 12-24 ppm. For the peak areas, the RSD was reduced from 28% to 16% for samples deposited twice onto two target plates over two days. [Figure not available: see fulltext.

Park size and disturbance: impact on soil heterogeneity - a case study Tel-Aviv- Jaffa.

NASA Astrophysics Data System (ADS)

Zhevelev, Helena; Sarah, Pariente; Oz, Atar

2015-04-01

Parks and gardens are poly-functional elements of great importance in urban areas, and can be used for optimization of physical and social components in these areas. This study aimed to investigate alteration of soil properties with land usages within urban park and with area size of park. Ten parks differed by size (2 - 50 acres) were chosen, in random, in Tel-Aviv- Jaffa city. Soil was sampled in four microenvironments ((lawn, path, picnic and peripheral area (unorganized area) of each the park)), in three points and three depth (0-2, 5-10 and 10-20 cm). Penetration depth was measured in all point of sampling. For each soil sample electrical conductivity and organic matter content were determined. Averages of penetration depth drastically increased from the most disturbed microenvironments (path and picnic) to the less disturbed ones (lawn and peripheral). The maximal heterogeneity (by variances and percentiles) of penetration depth was found in the peripheral area. In this area, penetration depth increased with increasing park size, i.e., from 2.6 cm to 3.7 cm in the small and large parks, respectively. Averages of organic matter content and electrical conductivity decreased with soil depth in all microenvironments and increased with decreasing disturbance of microenvironments. Maximal heterogeneity for both of these properties was found in the picnic area. Increase of park size was accompanied by increasing of organic matter content in the upper depth in the peripheral area, i.e., from 2.4% in the small parks to 4.5% in the large ones. In all microenvironments the increasing of averages of all studied soil properties was accompanied by increasing heterogeneity, i.e., variances and upper percentiles. The increase in the heterogeneity of the studied soil properties is attributed to improved ecological soil status in the peripheral area, on the one hand, and to the high anthropogenic pressure in the picnic area, on the other. This means that the urban park offers "islands" with better ecological conditions which improve the urban system.

Imaging a Large Sample with Selective Plane Illumination Microscopy Based on Multiple Fluorescent Microsphere Tracking

NASA Astrophysics Data System (ADS)

Ryu, Inkeon; Kim, Daekeun

2018-04-01

A typical selective plane illumination microscopy (SPIM) image size is basically limited by the field of view, which is a characteristic of the objective lens. If an image larger than the imaging area of the sample is to be obtained, image stitching, which combines step-scanned images into a single panoramic image, is required. However, accurately registering the step-scanned images is very difficult because the SPIM system uses a customized sample mount where uncertainties for the translational and the rotational motions exist. In this paper, an image registration technique based on multiple fluorescent microsphere tracking is proposed in the view of quantifying the constellations and measuring the distances between at least two fluorescent microspheres embedded in the sample. Image stitching results are demonstrated for optically cleared large tissue with various staining methods. Compensation for the effect of the sample rotation that occurs during the translational motion in the sample mount is also discussed.

Estimating accuracy of land-cover composition from two-stage cluster sampling

USGS Publications Warehouse

Stehman, S.V.; Wickham, J.D.; Fattorini, L.; Wade, T.D.; Baffetta, F.; Smith, J.H.

2009-01-01

Land-cover maps are often used to compute land-cover composition (i.e., the proportion or percent of area covered by each class), for each unit in a spatial partition of the region mapped. We derive design-based estimators of mean deviation (MD), mean absolute deviation (MAD), root mean square error (RMSE), and correlation (CORR) to quantify accuracy of land-cover composition for a general two-stage cluster sampling design, and for the special case of simple random sampling without replacement (SRSWOR) at each stage. The bias of the estimators for the two-stage SRSWOR design is evaluated via a simulation study. The estimators of RMSE and CORR have small bias except when sample size is small and the land-cover class is rare. The estimator of MAD is biased for both rare and common land-cover classes except when sample size is large. A general recommendation is that rare land-cover classes require large sample sizes to ensure that the accuracy estimators have small bias. ?? 2009 Elsevier Inc.

A summary of chemical and biological testing of proposed disposal of sediment from Richmond Harbor relative to the Deep Off-Shelf Reference Area, the Bay Farm Borrow Area, and the Alcatraz Environs Reference Area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayhew, H.L.; Karle, L.M.; Gruendell, B.D.

The US Army Corps of Engineers was authorized to dredge Richmond Harbor to accomodate large, deep-draft vessels. An ecological evaluation of the Harbor sediments was performed describing the physical characteristics, toxic substances, effects on aquatic organisms,and potential for bioaccumulation of chemical contaminants. The objective of this report is to compare the sediment chemistry, acute toxicity, and bioaccumulation results of the Richmond Harbor sediments to each of the reference areas; i.e., the Deep Off-Shelf Reference Area, the Bay Farm Borrow Area, and the Alcatraz Environs Reference Area. This report will enable the US Army Corps of Engineers to determine whether disposalmore » at a reference area is appropriate for all or part of the dredged material from Richmond Harbor. Chemical analyses were performed on 30 sediment samples; 28 of those samples were then combined to form 7 composites. The seven composites plus sediment from two additional stations received both chemical and biological evaluations.« less

[Identification of communities endemic for urinary bilharziosis by the "Lot Quality Assurance Sampling" method in Madagascar].

PubMed

Rabarijaona, L P; Andriamaroson, B J; Ravaoalimalala, V E; Ravoniarimbinina, P; Migliani, R

2001-01-01

Reduction of morbidity is the main component in the National Schistosomiasis Control Program in Madagascar. The lot quality assurance sampling (LQAS) method has previously been shown as a useful tool in assessment of immunization coverage. A study was carried in the western part of Madagascar aiming to evaluate the applicability of the method in measuring the level of Schistosoma haematobium endemic level in different communities. Parasitological examination of urine samples from 1,124 children aged 5 to 19 years from 12 different schools by use of filtration technique constituted the reference in determining the prevalence. Three schools were found hyper-endemic (prevalence more than 60%), 5 schools were intermediate-endemic (prevalence between 30 to 59%), and 4 were hypo-endemic (prevalence less than 30%). Those figures indicate a heterogeneous distribution of S. haematobium in the study area. A sampling plan (16.6) was then tested in the same area while other sampling plans were simulated in the laboratory. School teachers randomized under supervision the children to participate in this study and collected urine samples. All sampling plans (16.6), (14.5), (12.4), (10.3), (8.2), (6.1) et (4.0) allowed correct identification of hyper-endemic and hypo-endemic areas. Misclassifications occurred frequently for intermediate-endemic areas. The study confirms that the LQAS method by use of a (16.6) sampling plan constitute a valuable tool for large scale screening of hyper-endemic areas for therapeutic intervention as part of the control program. The study has also shown that school teachers may offer a potential source of manpower locally in such screening operations.

Fluence Uniformity Measurements in an Electron Accelerator Used for Irradiation of Extended Area Solar Cells and Electronic Circuits for Space Applications

NASA Technical Reports Server (NTRS)

Uribe, Roberto M.; Filppi, Ed; Zhang, Shubo

2007-01-01

It is common to have liquid crystal displays and electronic circuit boards with area sizes of the order of 20x20 sq cm on board of satellites and space vehicles. Usually irradiating them at different fluence values assesses the radiation damage in these types of devices. As a result, there is a need for a radiation source with large spatial fluence uniformity for the study of the damage by radiation from space in those devices. Kent State University s Program on Electron Beam Technology has access to an electron accelerator used for both research and industrial applications. The electron accelerator produces electrons with energies in the interval from 1 to 5 MeV and a maximum beam power of 150 kW. At such high power levels, the electron beam is continuously scanned back and forth in one dimension in order to provide uniform irradiation and to prevent damage to the sample. This allows for the uniform irradiation of samples with an area of up to 1.32 sq m. This accelerator has been used in the past for the study of radiation damage in solar cells (1). However in order to irradiate extended area solar cells there was a need to measure the uniformity of the irradiation zone in terms of fluence. In this paper the methodology to measure the fluence uniformity on a sample handling system (linear motion system), used for the irradiation of research samples, along the irradiation zone of the above-mentioned facility is described and the results presented. We also illustrate the use of the electron accelerator for the irradiation of large area solar cells (of the order of 156 sq cm) and include in this paper the electrical characterization of these types of solar cells irradiated with 5 MeV electrons to a total fluence of 2.6 x 10(exp 15) e/sq cm.

Enhanced-locality fiber-optic two-photon-fluorescence live-brain interrogation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fedotov, I. V.; Doronina-Amitonova, L. V.; Russian Quantum Center, ul. Novaya 100, Skolkovo, Moscow Region 1430125

2014-02-24

Two-photon excitation is shown to substantially enhance the locality of fiber-based optical interrogation of strongly scattering biotissues. In our experiments, a high-numerical-aperture, large-core-are fiber probe is used to deliver the 200-fs output of a 100-MHz mode-locked ytterbium fiber laser to samples of live mouse brain, induce two-photon fluorescence of nitrogen–vacancy centers in diamond markers in brain sample. Fiber probes with a high numerical aperture and a large core area are shown to enable locality enhancement in fiber-laser–fiber-probe two-photon brain excitation and interrogation without sacrificing the efficiency of fluorescence response collection.

Comparing the accuracy and precision of three techniques used for estimating missing landmarks when reconstructing fossil hominin crania.

PubMed

Neeser, Rudolph; Ackermann, Rebecca Rogers; Gain, James

2009-09-01

Various methodological approaches have been used for reconstructing fossil hominin remains in order to increase sample sizes and to better understand morphological variation. Among these, morphometric quantitative techniques for reconstruction are increasingly common. Here we compare the accuracy of three approaches--mean substitution, thin plate splines, and multiple linear regression--for estimating missing landmarks of damaged fossil specimens. Comparisons are made varying the number of missing landmarks, sample sizes, and the reference species of the population used to perform the estimation. The testing is performed on landmark data from individuals of Homo sapiens, Pan troglodytes and Gorilla gorilla, and nine hominin fossil specimens. Results suggest that when a small, same-species fossil reference sample is available to guide reconstructions, thin plate spline approaches perform best. However, if no such sample is available (or if the species of the damaged individual is uncertain), estimates of missing morphology based on a single individual (or even a small sample) of close taxonomic affinity are less accurate than those based on a large sample of individuals drawn from more distantly related extant populations using a technique (such as a regression method) able to leverage the information (e.g., variation/covariation patterning) contained in this large sample. Thin plate splines also show an unexpectedly large amount of error in estimating landmarks, especially over large areas. Recommendations are made for estimating missing landmarks under various scenarios. Copyright 2009 Wiley-Liss, Inc.

Geographic patterns of elemental deposition in the Aegean region of Turkey indicated by the lichen, Xanthoria parietina (L.) Th. Fr.

PubMed

Yenisoy-Karakaş, S; Tuncel, S G

2004-08-15

Lichen samples from different parts of the world have been known to accumulate elements to a greater degree than higher plants, if they are exposed to these elements from the atmosphere or from water and sediments. It has been hypothesized that lichens can be used to monitor air pollution around point and area emission sources. Local variation (variation in substrate, age and morphology of lichen samples) of element concentrations would not be large enough to affect the concentration patterns in large areas. We tested this hypothesis in the Aegean region of Turkey, which is very urbanized and industrialized. No such study has been conducted before in this part of the country. A total of 234 samples of the lichen Xanthoria parietina were collected from a 51,800-km2 area. Samples were washed and analyzed by INAA and ICP-AES for 35 elements. The range of the concentrations for most of the elements on a local scale was an order of magnitude lower than for the element concentrations on a regional scale. The mean local coefficient of variance (CV) was found to be 15, providing that the local variation did not affect the concentration of elements in the sampling region. According to cluster analysis, 8 (As, Hg, Pb, Sb, Fe, Mn, Na and K) elements are indicative of important local pollution locations and their zone of impact in the region. By mapping the concentrations of eight indicative elements in lichen Xanthoria parietina of the Aegean region, it was possible to relate deposition to the existence of known sources of pollution in certain areas. Location of pollution sources such as iron-steel plants, and coal burning in the cities, industrial activity and two important coal-fired power plants generally corresponded with locations of highest element accumulations in the lichens.

The Arctic Soil Bacterial Communities in the Vicinity of a Little Auk Colony

PubMed Central

Zielińska, Sylwia; Kidawa, Dorota; Stempniewicz, Lech; Łoś, Marcin; Łoś, Joanna M.

2016-01-01

Due to deposition of birds' guano, eggshells or feathers, the vicinity of a large seabirds' breeding colony is expected to have a substantial impact on the soil's physicochemical features as well as on diversity of vegetation and the soil invertebrates. Consequently, due to changing physicochemical features the structure of bacterial communities might fluctuate in different soil environments. The aim of this study was to investigate the bacterial assemblages in the Arctic soil within the area of a birds' colony and in a control sample from a topographically similar location but situated away from the colony's impact area. A high number of OTUs found in both areas indicates a highly complex microbial populations structure. The most abundant phyla in both of the tested samples were: Proteobacteria, Acidobacteria, Actinobacteria, and Chloroflexi, with different proportions in the total share. Despite differences in the physicochemical soil characteristics, the soil microbial community structures at the phylum level were similar to some extent in the two samples. The only share that was significantly higher in the control area when compared to the sample obtained within the birds' colony, belonged to the Actinobacteria phylum. Moreover, when analyzing the class level for each phylum, several differences between the samples were observed. Furthermore, lower proportions of Proteobacteria and Acidobacteria were observed in the soil sample under the influence of the bird's colony, which most probably could be linked to higher nitrogen concentrations in that sample. PMID:27667982

A Spaceflight Experiment to Determine the Effect of Chamfered Sample Holders on Atomic Oxygen Erosion

NASA Technical Reports Server (NTRS)

Girish, Kshama; Banks, Bruce A.; De Groh, Kim K.

2017-01-01

The exteriors of low Earth orbit (LEO) spacecraft are subjected to many environmental threats that can cause the surface materials to degrade. One of these threats is atomic oxygen (AO), which is formed by photo dissociation of molecular oxygen by energetic UV radiation. Atomic oxygen exposure can result in oxidative erosion of polymers leading to structural or thermal failure of spacecraft components. The amount of AO erosion expected during a mission can be calculated by knowing the AO erosion yield (Ey, volume loss per incident atom) of the material and the AO fluence expected for the mission. The Ey can be determined through dehydrated mass loss measurements of test samples if one knows the AO fluence, density, and exposure area. Such measurements have been made as part of flight experiments, including the Materials International Space Station Experiment 2 (MISSE 2) Polymers Experiment. The MISSE 2 Polymers Experiment sample holders had chamfered circular apertures that controlled the exposure area, but also allowed some additional AO to scatter from the chamfered edges onto the samples thus causing some samples to erode thru and peel at their perimeter due to this scattering effect. By modeling the scattered AO flux one can predict the actual total AO fluence, and hence more accurate sample Ey. Sample holders with different chamfered-perimeter to exposed-area ratios have been designed for future spaceflight experiments that allow a more accurate determination of the Ey for large area polymers, representative of their use on spacecraft surfaces.

The SDSS-III Multi-object Apo Radial-velocity Exoplanet Large-area Survey

NASA Astrophysics Data System (ADS)

Ge, Jian; Mahadevan, S.; Lee, B.; Wan, X.; Zhao, B.; van Eyken, J.; Kane, S.; Guo, P.; Ford, E. B.; Agol, E.; Gaudi, S.; Fleming, S.; Crepp, J.; Cohen, R.; Groot, J.; Galvez, M.; Liu, J.; Ford, H.; Schneider, D.; Seager, S.; Hawley, S. L.; Weinberg, D.; Eisenstein, D.

2007-12-01

As part of SDSS-III survey in 2008-2014, the Multi-object APO Radial-Velocity Exoplanet Large-area Survey (MARVELS) will conduct the largest ground-based Doppler planet survey to date using the SDSS telescope and new generation multi-object Doppler instruments with 120 object capability and 10-20 m/s Doppler precision. The baseline survey plan is to monitor a total of 11,000 V=8-12 stars ( 10,000 main sequence stars and 1000 giant stars) over 800 square degrees over the 6 years. The primary goal is to produce a large, statistically well defined sample of giant planets ( 200) with a wide range of masses ( 0.2-10 Jupiter masses) and orbits (1 day-2 years) drawn from a large of host stars with a diverse set of masses, compositions, and ages for studying the diversity of extrasolar planets and constraining planet formation, migration & dynamical evolution of planetary systems. The survey data will also be used for providing a statistical sample for theoretical comparison and discovering rare systems and identifying signposts for lower-mass or more distant planets. Early science results from the pilot program will be reported. We would like to thank the SDSS MC for allocation of the telescope time and the W.M. Keck Foundation, NSF, NASA and UF for support.

Race, urban context, and Russian roulette: findings from the National Violent Death Reporting System, 2003-2006.

PubMed

Wasserman, Ira; Stack, Steven

2011-02-01

Previous work on Russian roulette has focused on data from large cities. It is unclear if the epidemiological patterns based on large cities will replicate for the nation as a whole, and if the influence of minority status will be moderated by urban context. The present investigation fills these gaps by providing descriptive epidemiological data on Russian roulette for 17 states, and testing a hypothesis on urbanism as a moderator of the race-Russian roulette relationship. Data were taken from the National Violent Death Reporting System (2003-2006). They refer to 71 Russian roulette cases and a matched control group of 284 males who committed suicide by a gunshot wound to the head. Russian roulette suicides were more apt to be of minority status, younger, had a lower incidence of mental health problems, and were more likely to be utilizing alcohol than the controls. Differentiating the sample into larger and smaller urban areas, it was found that the risk of Russian roulette for African Americans was higher in larger urban areas. Epidemiological patterns in previous research on large city samples are largely replicated. The moderating influence of urban context is related to differential opportunity structures for risk-taking behavior. © 2011 The American Association of Suicidology.

VALIDATION OF STANDARD ANALYTICAL PROTOCOL FOR ...

EPA Pesticide Factsheets

There is a growing concern with the potential for terrorist use of chemical weapons to cause civilian harm. In the event of an actual or suspected outdoor release of chemically hazardous material in a large area, the extent of contamination must be determined. This requires a system with the ability to prepare and quickly analyze a large number of contaminated samples for the traditional chemical agents, as well as numerous toxic industrial chemicals. Liquid samples (both aqueous and organic), solid samples (e.g., soil), vapor samples (e.g., air) and mixed state samples, all ranging from household items to deceased animals, may require some level of analyses. To meet this challenge, the U.S. Environmental Protection Agency (U.S. EPA) National Homeland Security Research Center, in collaboration with experts from across U.S. EPA and other Federal Agencies, initiated an effort to identify analytical methods for the chemical and biological agents that could be used to respond to a terrorist attack or a homeland security incident. U.S. EPA began development of standard analytical protocols (SAPs) for laboratory identification and measurement of target agents in case of a contamination threat. These methods will be used to help assist in the identification of existing contamination, the effectiveness of decontamination, as well as clearance for the affected population to reoccupy previously contaminated areas. One of the first SAPs developed was for the determin

Implications from XMM and Chandra Source Catalogs for Future Studies with Lynx

NASA Astrophysics Data System (ADS)

Ptak, Andrew

2018-01-01

Lynx will perform extremely sensitive X-ray surveys by combining very high-resolution imaging over a large field of view with a high effective area. These will include deep planned surveys and serendipitous source surveys. Here we discuss implications that can be gleaned from current Chandra and XMM-Newton serendipitous source surveys. These current surveys have discovered novel sources such as tidal disruption events, binary AGN, and ULX pulsars. In addition these surveys have detected large samples of normal galaxies, low-luminosity AGN and quasars due to the wide-area coverage of the Chandra and XMM-Newton source catalogs, allowing the evolution of these phenonema to be explored. The wide area Lynx surveys will probe down further in flux and will be coupled with very sensitive wide-area surveys such as LSST and SKA, allowing for detailed modeling of their SEDs and the discovery of rare, exotic sources and transient events.

Spatial Statistical Models and Optimal Survey Design for Rapid Geophysical characterization of UXO Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

G. Ostrouchov; W.E.Doll; D.A.Wolf

2003-07-01

Unexploded ordnance(UXO)surveys encompass large areas, and the cost of surveying these areas can be high. Enactment of earlier protocols for sampling UXO sites have shown the shortcomings of these procedures and led to a call for development of scientifically defensible statistical procedures for survey design and analysis. This project is one of three funded by SERDP to address this need.

Accuracy assessment in the Large Area Crop Inventory Experiment

NASA Technical Reports Server (NTRS)

Houston, A. G.; Pitts, D. E.; Feiveson, A. H.; Badhwar, G.; Ferguson, M.; Hsu, E.; Potter, J.; Chhikara, R.; Rader, M.; Ahlers, C.

1979-01-01

The Accuracy Assessment System (AAS) of the Large Area Crop Inventory Experiment (LACIE) was responsible for determining the accuracy and reliability of LACIE estimates of wheat production, area, and yield, made at regular intervals throughout the crop season, and for investigating the various LACIE error sources, quantifying these errors, and relating them to their causes. Some results of using the AAS during the three years of LACIE are reviewed. As the program culminated, AAS was able not only to meet the goal of obtaining accurate statistical estimates of sampling and classification accuracy, but also the goal of evaluating component labeling errors. Furthermore, the ground-truth data processing matured from collecting data for one crop (small grains) to collecting, quality-checking, and archiving data for all crops in a LACIE small segment.

Attenuated total internal reflection infrared microspectroscopic imaging using a large-radius germanium internal reflection element and a linear array detector.

PubMed

Patterson, Brian M; Havrilla, George J

2006-11-01

The number of techniques and instruments available for Fourier transform infrared (FT-IR) microspectroscopic imaging has grown significantly over the past few years. Attenuated total internal reflectance (ATR) FT-IR microspectroscopy reduces sample preparation time and has simplified the analysis of many difficult samples. FT-IR imaging has become a powerful analytical tool using either a focal plane array or a linear array detector, especially when coupled with a chemometric analysis package. The field of view of the ATR-IR microspectroscopic imaging area can be greatly increased from 300 x 300 microm to 2500 x 2500 microm using a larger internal reflection element of 12.5 mm radius instead of the typical 1.5 mm radius. This gives an area increase of 70x before aberrant effects become too great. Parameters evaluated include the change in penetration depth as a function of beam displacement, measurements of the active area, magnification factor, and change in spatial resolution over the imaging area. Drawbacks such as large file size will also be discussed. This technique has been successfully applied to the FT-IR imaging of polydimethylsiloxane foam cross-sections, latent human fingerprints, and a model inorganic mixture, which demonstrates the usefulness of the method for pharmaceuticals.

Parcellating an Individual Subject's Cortical and Subcortical Brain Structures Using Snowball Sampling of Resting-State Correlations

PubMed Central

Wig, Gagan S.; Laumann, Timothy O.; Cohen, Alexander L.; Power, Jonathan D.; Nelson, Steven M.; Glasser, Matthew F.; Miezin, Francis M.; Snyder, Abraham Z.; Schlaggar, Bradley L.; Petersen, Steven E.

2014-01-01

We describe methods for parcellating an individual subject's cortical and subcortical brain structures using resting-state functional correlations (RSFCs). Inspired by approaches from social network analysis, we first describe the application of snowball sampling on RSFC data (RSFC-Snowballing) to identify the centers of cortical areas, subdivisions of subcortical nuclei, and the cerebellum. RSFC-Snowballing parcellation is then compared with parcellation derived from identifying locations where RSFC maps exhibit abrupt transitions (RSFC-Boundary Mapping). RSFC-Snowballing and RSFC-Boundary Mapping largely complement one another, but also provide unique parcellation information; together, the methods identify independent entities with distinct functional correlations across many cortical and subcortical locations in the brain. RSFC parcellation is relatively reliable within a subject scanned across multiple days, and while the locations of many area centers and boundaries appear to exhibit considerable overlap across subjects, there is also cross-subject variability—reinforcing the motivation to parcellate brains at the level of individuals. Finally, examination of a large meta-analysis of task-evoked functional magnetic resonance imaging data reveals that area centers defined by task-evoked activity exhibit correspondence with area centers defined by RSFC-Snowballing. This observation provides important evidence for the ability of RSFC to parcellate broad expanses of an individual's brain into functionally meaningful units. PMID:23476025

Cross-sectional TEM specimen preparation for W/B{sub 4}C multilayer sample using FIB

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mondal, Puspen, E-mail: puspen@rrcat.gov.in; Pradhan, P. C.; Tiwari, Pragya

2016-05-23

A recent emergence of a cross-beam scanning electron microscopy (SEM)/focused-ion-beam (FIB) system have given choice to fabricate cross-sectional transmission electron microscopy (TEM) specimen of thin film multilayer sample. A 300 layer pair thin film multilayer sample of W/B{sub 4}C was used to demonstrate the specimen lift-out technique in very short time as compared to conventional cross-sectional sample preparation technique. To get large area electron transparent sample, sample prepared by FIB is followed by Ar{sup +} ion polishing at 2 kV with grazing incident. The prepared cross-sectional sample was characterized by transmission electron microscope.

Seismic sample areas defined from incomplete catalogues: an application to the Italian territory

NASA Astrophysics Data System (ADS)

Mulargia, F.; Tinti, S.

1985-11-01

The comprehensive understanding of earthquake source-physics under real conditions requires the study not of single faults as separate entities but rather of a seismically active region as a whole, accounting for the interaction among different structures. We define "seismic sample area" the most convenient region to be used as a natural laboratory for the study of seismic source physics. This coincides with the region where the average large magnitude seismicity is the highest. To this end, time and space future distributions of large earthquakes are to be estimated. Using catalog seismicity as an input, the rate of occurrence is not constant but appears generally biased by incompleteness in some parts of the catalog and possible nonstationarities in seismic activity. We present a statistical procedure which is capable, under a few mild assumptions, of both detecting nonstationarities in seismicity and finding the incomplete parts of a seismic catalog. The procedure is based on Kolmogorov-Smirnov nonparametric statistics, and can be applied without a priori assuming the parent distribution of the events. The efficiency of this procedure allows the analysis of small data sets. An application to the Italian territory is presented, using the most recent version of the ENEL seismic catalog. Seismic activity takes place in six well defined areas but only five of them have a number of events sufficient for analysis. Barring a few exceptions, seismicity is found stationary throughout the whole catalog span 1000-1980. The eastern Alps region stands out as the best "sample area", with the highest average probability of event occurrence per time and area unit. Final objective of this characterization is to stimulate a program of intensified research.

Analysis of area level and unit level models for small area estimation in forest inventories assisted with LiDAR auxiliary information.

PubMed

Mauro, Francisco; Monleon, Vicente J; Temesgen, Hailemariam; Ford, Kevin R

2017-01-01

Forest inventories require estimates and measures of uncertainty for subpopulations such as management units. These units often times hold a small sample size, so they should be regarded as small areas. When auxiliary information is available, different small area estimation methods have been proposed to obtain reliable estimates for small areas. Unit level empirical best linear unbiased predictors (EBLUP) based on plot or grid unit level models have been studied more thoroughly than area level EBLUPs, where the modelling occurs at the management unit scale. Area level EBLUPs do not require a precise plot positioning and allow the use of variable radius plots, thus reducing fieldwork costs. However, their performance has not been examined thoroughly. We compared unit level and area level EBLUPs, using LiDAR auxiliary information collected for inventorying 98,104 ha coastal coniferous forest. Unit level models were consistently more accurate than area level EBLUPs, and area level EBLUPs were consistently more accurate than field estimates except for large management units that held a large sample. For stand density, volume, basal area, quadratic mean diameter, mean height and Lorey's height, root mean squared errors (rmses) of estimates obtained using area level EBLUPs were, on average, 1.43, 2.83, 2.09, 1.40, 1.32 and 1.64 times larger than those based on unit level estimates, respectively. Similarly, direct field estimates had rmses that were, on average, 1.37, 1.45, 1.17, 1.17, 1.26, and 1.38 times larger than rmses of area level EBLUPs. Therefore, area level models can lead to substantial gains in accuracy compared to direct estimates, and unit level models lead to very important gains in accuracy compared to area level models, potentially justifying the additional costs of obtaining accurate field plot coordinates.

Analysis of area level and unit level models for small area estimation in forest inventories assisted with LiDAR auxiliary information

PubMed Central

Monleon, Vicente J.; Temesgen, Hailemariam; Ford, Kevin R.

2017-01-01

Forest inventories require estimates and measures of uncertainty for subpopulations such as management units. These units often times hold a small sample size, so they should be regarded as small areas. When auxiliary information is available, different small area estimation methods have been proposed to obtain reliable estimates for small areas. Unit level empirical best linear unbiased predictors (EBLUP) based on plot or grid unit level models have been studied more thoroughly than area level EBLUPs, where the modelling occurs at the management unit scale. Area level EBLUPs do not require a precise plot positioning and allow the use of variable radius plots, thus reducing fieldwork costs. However, their performance has not been examined thoroughly. We compared unit level and area level EBLUPs, using LiDAR auxiliary information collected for inventorying 98,104 ha coastal coniferous forest. Unit level models were consistently more accurate than area level EBLUPs, and area level EBLUPs were consistently more accurate than field estimates except for large management units that held a large sample. For stand density, volume, basal area, quadratic mean diameter, mean height and Lorey’s height, root mean squared errors (rmses) of estimates obtained using area level EBLUPs were, on average, 1.43, 2.83, 2.09, 1.40, 1.32 and 1.64 times larger than those based on unit level estimates, respectively. Similarly, direct field estimates had rmses that were, on average, 1.37, 1.45, 1.17, 1.17, 1.26, and 1.38 times larger than rmses of area level EBLUPs. Therefore, area level models can lead to substantial gains in accuracy compared to direct estimates, and unit level models lead to very important gains in accuracy compared to area level models, potentially justifying the additional costs of obtaining accurate field plot coordinates. PMID:29216290

Evaluating effectiveness of down-sampling for stratified designs and unbalanced prevalence in Random Forest models of tree species distributions in Nevada

Treesearch

Elizabeth A. Freeman; Gretchen G. Moisen; Tracy S. Frescino

2012-01-01

Random Forests is frequently used to model species distributions over large geographic areas. Complications arise when data used to train the models have been collected in stratified designs that involve different sampling intensity per stratum. The modeling process is further complicated if some of the target species are relatively rare on the landscape leading to an...

Evaluating Site-Specific and Generic Spatial Models of Aboveground Forest Biomass Based on Landsat Time-Series and LiDAR Strip Samples in the Eastern USA

Treesearch

Ram Deo; Matthew Russell; Grant Domke; Hans-Erik Andersen; Warren Cohen; Christopher Woodall

2017-01-01

Large-area assessment of aboveground tree biomass (AGB) to inform regional or national forest monitoring programs can be efficiently carried out by combining remotely sensed data and field sample measurements through a generic statistical model, in contrast to site-specific models. We integrated forest inventory plot data with spatial predictors from Landsat time-...

Camphor-Enabled Transfer and Mechanical Testing of Centimeter-Scale Ultrathin Films.

PubMed

Wang, Bin; Luo, Da; Li, Zhancheng; Kwon, Youngwoo; Wang, Meihui; Goo, Min; Jin, Sunghwan; Huang, Ming; Shen, Yongtao; Shi, Haofei; Ding, Feng; Ruoff, Rodney S

2018-05-21

Camphor is used to transfer centimeter-scale ultrathin films onto custom-designed substrates for mechanical (tensile) testing. Compared to traditional transfer methods using dissolving/peeling to remove the support-layers, camphor is sublimed away in air at low temperature, thereby avoiding additional stress on the as-transferred films. Large-area ultrathin films can be transferred onto hollow substrates without damage by this method. Tensile measurements are made on centimeter-scale 300 nm-thick graphene oxide film specimens, much thinner than the ≈2 μm minimum thickness of macroscale graphene-oxide films previously reported. Tensile tests were also done on two different types of large-area samples of adlayer free CVD-grown single-layer graphene supported by a ≈100 nm thick polycarbonate film; graphene stiffens this sample significantly, thus the intrinsic mechanical response of the graphene can be extracted. This is the first tensile measurement of centimeter-scale monolayer graphene films. The Young's modulus of polycrystalline graphene ranges from 637 to 793 GPa, while for near single-crystal graphene, it ranges from 728 to 908 GPa (folds parallel to the tensile loading direction) and from 683 to 775 GPa (folds orthogonal to the tensile loading direction), demonstrating the mechanical performance of large-area graphene in a size scale relevant to many applications. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An iterative and targeted sampling design informed by habitat suitability models for detecting focal plant species over extensive areas.

PubMed

Wang, Ophelia; Zachmann, Luke J; Sesnie, Steven E; Olsson, Aaryn D; Dickson, Brett G

2014-01-01

Prioritizing areas for management of non-native invasive plants is critical, as invasive plants can negatively impact plant community structure. Extensive and multi-jurisdictional inventories are essential to prioritize actions aimed at mitigating the impact of invasions and changes in disturbance regimes. However, previous work devoted little effort to devising sampling methods sufficient to assess the scope of multi-jurisdictional invasion over extensive areas. Here we describe a large-scale sampling design that used species occurrence data, habitat suitability models, and iterative and targeted sampling efforts to sample five species and satisfy two key management objectives: 1) detecting non-native invasive plants across previously unsampled gradients, and 2) characterizing the distribution of non-native invasive plants at landscape to regional scales. Habitat suitability models of five species were based on occurrence records and predictor variables derived from topography, precipitation, and remotely sensed data. We stratified and established field sampling locations according to predicted habitat suitability and phenological, substrate, and logistical constraints. Across previously unvisited areas, we detected at least one of our focal species on 77% of plots. In turn, we used detections from 2011 to improve habitat suitability models and sampling efforts in 2012, as well as additional spatial constraints to increase detections. These modifications resulted in a 96% detection rate at plots. The range of habitat suitability values that identified highly and less suitable habitats and their environmental conditions corresponded to field detections with mixed levels of agreement. Our study demonstrated that an iterative and targeted sampling framework can address sampling bias, reduce time costs, and increase detections. Other studies can extend the sampling framework to develop methods in other ecosystems to provide detection data. The sampling methods implemented here provide a meaningful tool when understanding the potential distribution and habitat of species over multi-jurisdictional and extensive areas is needed for achieving management objectives.

An Iterative and Targeted Sampling Design Informed by Habitat Suitability Models for Detecting Focal Plant Species over Extensive Areas

PubMed Central

Wang, Ophelia; Zachmann, Luke J.; Sesnie, Steven E.; Olsson, Aaryn D.; Dickson, Brett G.

2014-01-01

Prioritizing areas for management of non-native invasive plants is critical, as invasive plants can negatively impact plant community structure. Extensive and multi-jurisdictional inventories are essential to prioritize actions aimed at mitigating the impact of invasions and changes in disturbance regimes. However, previous work devoted little effort to devising sampling methods sufficient to assess the scope of multi-jurisdictional invasion over extensive areas. Here we describe a large-scale sampling design that used species occurrence data, habitat suitability models, and iterative and targeted sampling efforts to sample five species and satisfy two key management objectives: 1) detecting non-native invasive plants across previously unsampled gradients, and 2) characterizing the distribution of non-native invasive plants at landscape to regional scales. Habitat suitability models of five species were based on occurrence records and predictor variables derived from topography, precipitation, and remotely sensed data. We stratified and established field sampling locations according to predicted habitat suitability and phenological, substrate, and logistical constraints. Across previously unvisited areas, we detected at least one of our focal species on 77% of plots. In turn, we used detections from 2011 to improve habitat suitability models and sampling efforts in 2012, as well as additional spatial constraints to increase detections. These modifications resulted in a 96% detection rate at plots. The range of habitat suitability values that identified highly and less suitable habitats and their environmental conditions corresponded to field detections with mixed levels of agreement. Our study demonstrated that an iterative and targeted sampling framework can address sampling bias, reduce time costs, and increase detections. Other studies can extend the sampling framework to develop methods in other ecosystems to provide detection data. The sampling methods implemented here provide a meaningful tool when understanding the potential distribution and habitat of species over multi-jurisdictional and extensive areas is needed for achieving management objectives. PMID:25019621

The ALHAMBRA survey: evolution of galaxy clustering since z ˜ 1

NASA Astrophysics Data System (ADS)

Arnalte-Mur, P.; Martínez, V. J.; Norberg, P.; Fernández-Soto, A.; Ascaso, B.; Merson, A. I.; Aguerri, J. A. L.; Castander, F. J.; Hurtado-Gil, L.; López-Sanjuan, C.; Molino, A.; Montero-Dorta, A. D.; Stefanon, M.; Alfaro, E.; Aparicio-Villegas, T.; Benítez, N.; Broadhurst, T.; Cabrera-Caño, J.; Cepa, J.; Cerviño, M.; Cristóbal-Hornillos, D.; del Olmo, A.; González Delgado, R. M.; Husillos, C.; Infante, L.; Márquez, I.; Masegosa, J.; Moles, M.; Perea, J.; Pović, M.; Prada, F.; Quintana, J. M.

2014-06-01

We study the clustering of galaxies as function of luminosity and redshift in the range 0.35 < z < 1.25 using data from the Advanced Large Homogeneous Area Medium-Band Redshift Astronomical (ALHAMBRA) survey. The ALHAMBRA data used in this work cover 2.38 deg2 in seven independent fields, after applying a detailed angular selection mask, with accurate photometric redshifts, σz ≲ 0.014(1 + z), down to IAB < 24. Given the depth of the survey, we select samples in B-band luminosity down to Lth ≃ 0.16L* at z = 0.9. We measure the real-space clustering using the projected correlation function, accounting for photometric redshifts uncertainties. We infer the galaxy bias, and study its evolution with luminosity. We study the effect of sample variance, and confirm earlier results that the Cosmic Evolution Survey (COSMOS) and European Large Area ISO Survey North 1 (ELAIS-N1) fields are dominated by the presence of large structures. For the intermediate and bright samples, Lmed ≳ 0.6L*, we obtain a strong dependence of bias on luminosity, in agreement with previous results at similar redshift. We are able to extend this study to fainter luminosities, where we obtain an almost flat relation, similar to that observed at low redshift. Regarding the evolution of bias with redshift, our results suggest that the different galaxy populations studied reside in haloes covering a range in mass between log10[Mh/( h-1 M⊙)] ≳ 11.5 for samples with Lmed ≃ 0.3L* and log10[Mh/( h-1 M⊙)] ≳ 13.0 for samples with Lmed ≃ 2L*, with typical occupation numbers in the range of ˜1-3 galaxies per halo.

After site selection and before data analysis: sampling, sorting, and laboratory procedures used in stream benthic macroinvertebrate monitoring programs by USA state agencies

USGS Publications Warehouse

Carter, James L.; Resh, Vincent H.

2001-01-01

A survey of methods used by US state agencies for collecting and processing benthic macroinvertebrate samples from streams was conducted by questionnaire; 90 responses were received and used to describe trends in methods. The responses represented an estimated 13,000-15,000 samples collected and processed per year. Kicknet devices were used in 64.5% of the methods; other sampling devices included fixed-area samplers (Surber and Hess), artificial substrates (Hester-Dendy and rock baskets), grabs, and dipnets. Regional differences existed, e.g., the 1-m kicknet was used more often in the eastern US than in the western US. Mesh sizes varied among programs but 80.2% of the methods used a mesh size between 500 and 600 (mu or u)m. Mesh size variations within US Environmental Protection Agency regions were large, with size differences ranging from 100 to 700 (mu or u)m. Most samples collected were composites; the mean area sampled was 1.7 m2. Samples rarely were collected using a random method (4.7%); most samples (70.6%) were collected using "expert opinion", which may make data obtained operator-specific. Only 26.3% of the methods sorted all the organisms from a sample; the remainder subsampled in the laboratory. The most common method of subsampling was to remove 100 organisms (range = 100-550). The magnification used for sorting ranged from 1 (sorting by eye) to 30x, which results in inconsistent separation of macroinvertebrates from detritus. In addition to subsampling, 53% of the methods sorted large/rare organisms from a sample. The taxonomic level used for identifying organisms varied among taxa; Ephemeroptera, Plecoptera, and Trichoptera were generally identified to a finer taxonomic resolution (genus and species) than other taxa. Because there currently exists a large range of field and laboratory methods used by state programs, calibration among all programs to increase data comparability would be exceptionally challenging. However, because many techniques are shared among methods, limited testing could be designed to evaluate whether procedural differences affect the ability to determine levels of environmental impairment using benthic macroinvertebrate communities.

Lightweight aggregate production from claystone and shale in Bangladesh

USGS Publications Warehouse

Parker, Norbert A.; Khan, M.A.

1976-01-01

Muffle furnace tests were made on samples of clay, claystone, and shale collected in the Chittagong and Dacca areas of East Pakistan to determine their amenability to bloating for the commercial production of light-weight aggregate. Several areas, sampled in some detail, were selected for investigation because of their proximity to market, and accessibility to fuel and electricity. Muffle furnace tests show that the clay, claystone, and shale are natural bloaters at temperatures in the 1700? to 2200? F range, and do not require additives. The most desirable deposit, insofar as producing a strong aggregate is concerned, can be determined only by pilot-kiln testing and by crushing-strength tests made on concrete test cylinders. Reserves of suitable raw material are large in both the Chittagong and Dacca areas.

Open-Source Automated Mapping Four-Point Probe

PubMed Central

Chandra, Handy; Allen, Spencer W.; Oberloier, Shane W.; Bihari, Nupur; Gwamuri, Jephias; Pearce, Joshua M.

2017-01-01

Scientists have begun using self-replicating rapid prototyper (RepRap) 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP) measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO) samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas. PMID:28772471

On plate graphite supported sample processing for simultaneous lipid and protein identification by matrix assisted laser desorption ionization mass spectrometry.

PubMed

Calvano, Cosima Damiana; van der Werf, Inez Dorothé; Sabbatini, Luigia; Palmisano, Francesco

2015-05-01

The simultaneous identification of lipids and proteins by matrix assisted laser desorption ionization-mass spectrometry (MALDI-MS) after direct on-plate processing of micro-samples supported on colloidal graphite is demonstrated. Taking advantages of large surface area and thermal conductivity, graphite provided an ideal substrate for on-plate proteolysis and lipid extraction. Indeed proteins could be efficiently digested on-plate within 15 min, providing sequence coverages comparable to those obtained by conventional in-solution overnight digestion. Interestingly, detection of hydrophilic phosphorylated peptides could be easily achieved without any further enrichment step. Furthermore, lipids could be simultaneously extracted/identified without any additional treatment/processing step as demonstrated for model complex samples such as milk and egg. The present approach is simple, efficient, of large applicability and offers great promise for protein and lipid identification in very small samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Response Variability in Commercial MOSFET SEE Qualification

DOE PAGES

George, J. S.; Clymer, D. A.; Turflinger, T. L.; ...

2016-12-01

Single-event effects (SEE) evaluation of five different part types of next generation, commercial trench MOSFETs indicates large part-to-part variation in determining a safe operating area (SOA) for drain-source voltage (V DS) following a test campaign that exposed >50 samples per part type to heavy ions. These results suggest a determination of a SOA using small sample sizes may fail to capture the full extent of the part-to-part variability. An example method is discussed for establishing a Safe Operating Area using a one-sided statistical tolerance limit based on the number of test samples. Finally, burn-in is shown to be a criticalmore » factor in reducing part-to-part variation in part response. Implications for radiation qualification requirements are also explored.« less

Response Variability in Commercial MOSFET SEE Qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, J. S.; Clymer, D. A.; Turflinger, T. L.

Single-event effects (SEE) evaluation of five different part types of next generation, commercial trench MOSFETs indicates large part-to-part variation in determining a safe operating area (SOA) for drain-source voltage (V DS) following a test campaign that exposed >50 samples per part type to heavy ions. These results suggest a determination of a SOA using small sample sizes may fail to capture the full extent of the part-to-part variability. An example method is discussed for establishing a Safe Operating Area using a one-sided statistical tolerance limit based on the number of test samples. Finally, burn-in is shown to be a criticalmore » factor in reducing part-to-part variation in part response. Implications for radiation qualification requirements are also explored.« less

Estimation of sampling error uncertainties in observed surface air temperature change in China

NASA Astrophysics Data System (ADS)

Hua, Wei; Shen, Samuel S. P.; Weithmann, Alexander; Wang, Huijun

2017-08-01

This study examines the sampling error uncertainties in the monthly surface air temperature (SAT) change in China over recent decades, focusing on the uncertainties of gridded data, national averages, and linear trends. Results indicate that large sampling error variances appear at the station-sparse area of northern and western China with the maximum value exceeding 2.0 K2 while small sampling error variances are found at the station-dense area of southern and eastern China with most grid values being less than 0.05 K2. In general, the negative temperature existed in each month prior to the 1980s, and a warming in temperature began thereafter, which accelerated in the early and mid-1990s. The increasing trend in the SAT series was observed for each month of the year with the largest temperature increase and highest uncertainty of 0.51 ± 0.29 K (10 year)-1 occurring in February and the weakest trend and smallest uncertainty of 0.13 ± 0.07 K (10 year)-1 in August. The sampling error uncertainties in the national average annual mean SAT series are not sufficiently large to alter the conclusion of the persistent warming in China. In addition, the sampling error uncertainties in the SAT series show a clear variation compared with other uncertainty estimation methods, which is a plausible reason for the inconsistent variations between our estimate and other studies during this period.

Detection of viral hemorrhagic septicemia in round gobies in New York State (USA) waters of Lake Ontario and the St. Lawrence River

USGS Publications Warehouse

Groocock, G.H.; Getchell, R.G.; Wooster, G.A.; Britt, K.L.; Batts, W.N.; Winton, J.R.; Casey, R.N.; Casey, J.W.; Bowser, P.R.

2007-01-01

In May 2006 a large mortality of several thousand round gobies Neogobius melanostomus (Pallas, 1814) occurred in New York waters of the St. Lawrence River and Lake Ontario. Necropsies of sampled fish from these areas showed pallor of the liver and gills, and hemorrhagic areas in many organs. Histopathologic examination of affected tissues revealed areas of necrosis and hemorrhage. Inoculations of fathead minnow Pimephales promelas (Rafinesque, 1820) cell cultures with dilutions of tissue samples from the necropsied gobies produced a cytopathic effect within 5 d post-inoculation. Samples of cell culture supernatant were tested using RT-PCR and confirmed the presence of viral hemorrhagic septicemia virus (VHSV). Sequence analysis of the VHSV isolate resulted in its assignment to the type-IVb subgroup. The detection of VHSV in a relatively recent invasive fish species in the Great Lakes and the potential impact of VHSV on the ecology and economy of the area will require further investigation and careful management considerations. ?? Inter-Research 2007.

Geochemical data for environmental studies of mineral deposits at Nabesna, Kennecott, Orange Hill, Bond Creek, Bremner, and Gold Hill, Wrangell-St. Elias National Park and Preserve, Alaska

USGS Publications Warehouse

Eppinger, R.G.; Briggs, P.H.; Rosenkrans, D.S.; Ballestrazze, Vanessa; Aldir, Jose; Brown, Z.A.; Crock, J.G.; d'Angelo, W. M.; Doughten, M.W.; Fey, D.L.; Hageman, P.L.; Hopkins, R.T.; Knight, R.J.; Malcolm, M.J.; McHugh, J.B.; Meier, A.L.; Motooka, J.M.; O'Leary, R. M.; Roushey, B.H.; Sultley, S.J.; Theodorakos, P.M.; Wilson, S.A.

1999-01-01

Environmental geochemical investigations were carried out between 1994 and 1997 in Wrangell-St. Elias National Park and Preserve (WRST), Alaska. Mineralized areas studied include the historic Nabesna gold mine/mill and surrounding areas; the historic Kennecott copper mill area and nearby Bonanza, Erie, Glacier, and Jumbo mines; the historic mill and gold mines in the Bremner district; the active gold placer mines at Gold Hill; and the unmined copper-molybdenum deposits at Orange Hill and Bond Creek. The purpose of the study was to determine the extent of possible environmental hazards associated with these mineralized areas and to establish background and baseline levels for selected elements. Thus, concentrations of a large suite of trace elements were determined to assess metal loadings in the various sample media collected. This report presents the methodology, analytical results, and sample descriptions for water, leachate, sediment, heavy-mineral concentrate, rock, and vegetation (willow) samples collected during these geochemical investigations. An interpretive U.S. Geological Survey Professional Paper incorporating these geochemical data will follow.

Analysis of defect structure in silicon. Silicon sheet growth development for the large area silicon sheet task of the Low-Cost Solar array Project

NASA Technical Reports Server (NTRS)

Natesh, R.; Mena, M.; Plichta, M.; Smith, J. M.; Sellani, M. A.

1982-01-01

One hundred ninety-three silicon sheet samples, approximately 880 square centimeters, were analyzed for twin boundary density, dislocation pit density, and grain boundary length. One hundred fifteen of these samples were manufactured by a heat exchanger method, thirty-eight by edge defined film fed growth, twenty-three by the silicon on ceramics process, and ten by the dendritic web process. Seven solar cells were also step-etched to determine the internal defect distribution on these samples. Procedures were developed or the quantitative characterization of structural defects such as dislocation pits, precipitates, twin & grain boundaries using a QTM 720 quantitative image analyzing system interfaced with a PDP 11/03 mini computer. Characterization of the grain boundary length per unit area for polycrystalline samples was done by using the intercept method on an Olympus HBM Microscope.

Computer-aided boundary delineation of agricultural lands

NASA Technical Reports Server (NTRS)

Cheng, Thomas D.; Angelici, Gary L.; Slye, Robert E.; Ma, Matt

1989-01-01

The National Agricultural Statistics Service of the United States Department of Agriculture (USDA) presently uses labor-intensive aerial photographic interpretation techniques to divide large geographical areas into manageable-sized units for estimating domestic crop and livestock production. Prototype software, the computer-aided stratification (CAS) system, was developed to automate the procedure, and currently runs on a Sun-based image processing system. With a background display of LANDSAT Thematic Mapper and United States Geological Survey Digital Line Graph data, the operator uses a cursor to delineate agricultural areas, called sampling units, which are assigned to strata of land-use and land-cover types. The resultant stratified sampling units are used as input into subsequent USDA sampling procedures. As a test, three counties in Missouri were chosen for application of the CAS procedures. Subsequent analysis indicates that CAS was five times faster in creating sampling units than the manual techniques were.

Complementarity of Rotating Video and Underwater Visual Census for Assessing Species Richness, Frequency and Density of Reef Fish on Coral Reef Slopes

PubMed Central

Mallet, Delphine; Wantiez, Laurent; Lemouellic, Soazig; Vigliola, Laurent; Pelletier, Dominique

2014-01-01

Estimating diversity and abundance of fish species is fundamental for understanding community structure and dynamics of coral reefs. When designing a sampling protocol, one crucial step is the choice of the most suitable sampling technique which is a compromise between the questions addressed, the available means and the precision required. The objective of this study is to compare the ability to sample reef fish communities at the same locations using two techniques based on the same stationary point count method: one using Underwater Visual Census (UVC) and the other rotating video (STAVIRO). UVC and STAVIRO observations were carried out on the exact same 26 points on the reef slope of an intermediate reef and the associated inner barrier reefs. STAVIRO systems were always deployed 30 min to 1 hour after UVC and set exactly at the same place. Our study shows that; (i) fish community observations by UVC and STAVIRO differed significantly; (ii) species richness and density of large species were not significantly different between techniques; (iii) species richness and density of small species were higher for UVC; (iv) density of fished species was higher for STAVIRO and (v) only UVC detected significant differences in fish assemblage structure across reef type at the spatial scale studied. We recommend that the two techniques should be used in a complementary way to survey a large area within a short period of time. UVC may census reef fish within complex habitats or in very shallow areas such as reef flat whereas STAVIRO would enable carrying out a large number of stations focused on large and diver-averse species, particularly in the areas not covered by UVC due to time and depth constraints. This methodology would considerably increase the spatial coverage and replication level of fish monitoring surveys. PMID:24392126

Spatial Variability of Sources and Mixing State of Atmospheric Particles in a Metropolitan Area.

PubMed

Ye, Qing; Gu, Peishi; Li, Hugh Z; Robinson, Ellis S; Lipsky, Eric; Kaltsonoudis, Christos; Lee, Alex K Y; Apte, Joshua S; Robinson, Allen L; Sullivan, Ryan C; Presto, Albert A; Donahue, Neil M

2018-05-30

Characterizing intracity variations of atmospheric particulate matter has mostly relied on fixed-site monitoring and quantifying variability in terms of different bulk aerosol species. In this study, we performed ground-based mobile measurements using a single-particle mass spectrometer to study spatial patterns of source-specific particles and the evolution of particle mixing state in 21 areas in the metropolitan area of Pittsburgh, PA. We selected sampling areas based on traffic density and restaurant density with each area ranging from 0.2 to 2 km 2 . Organics dominate particle composition in all of the areas we sampled while the sources of organics differ. The contribution of particles from traffic and restaurant cooking varies greatly on the neighborhood scale. We also investigate how primary and aged components in particles mix across the urban scale. Lastly we quantify and map the particle mixing state for all areas we sampled and discuss the overall pattern of mixing state evolution and its implications. We find that in the upwind and downwind of the urban areas, particles are more internally mixed while in the city center, particle mixing state shows large spatial heterogeneity that is mostly driven by emissions. This study is to our knowledge, the first study to perform fine spatial scale mapping of particle mixing state using ground-based mobile measurement and single-particle mass spectrometry.

A comparison of shoreline seines with fyke nets for sampling littoral fish communities in floodplain lakes

USGS Publications Warehouse

Clark, S.J.; Jackson, J.R.; Lochmann, S.E.

2007-01-01

We compared shoreline seines with fyke nets in terms of their ability to sample fish species in the littoral zone of 22 floodplain lakes of the White River, Arkansas. Lakes ranged in size from less than 0.5 to 51.0 ha. Most contained large amounts of coarse woody debris within the littoral zone, thus making seining in shallow areas difficult. We sampled large lakes (>2 ha) using three fyke nets; small lakes (<2 ha) were sampled using two fyke nets. Fyke nets were set for 24 h. Large lakes were sampled with an average of 11 seine hauls/ lake and small lakes were sampled with an average of 3 seine hauls/lake, but exact shoreline seining effort varied among lakes depending on the amount of open shoreline. Fyke nets collected more fish and produced greater species richness and diversity measures than did seining. Species evenness was similar for the two gear types. Two species were unique to seine samples, whereas 13 species and 3 families were unique to fyke-net samples. Although fyke nets collected more fish and more species than did shoreline seines, neither gear collected all the species present in the littoral zone of floodplain lakes. These results confirm the need for a multiple-gear approach to fully characterize the littoral fish assemblages in floodplain lakes. ?? Copyright by the American Fisheries Society 2007.

Contamination of River Water by Cryptosporidium parvum Oocysts in Western Japan

PubMed Central

Ono, Kazuo; Tsuji, Hidetaka; Rai, Shiba Kumar; Yamamoto, Akio; Masuda, Kuniyoshi; Endo, Takuro; Hotta, Hak; Kawamura, Takashi; Uga, Shoji

2001-01-01

In Japan, only a few rivers have been inspected for Cryptosporidium parvum contamination, and the methods used had low sensitivity. In 1998 and 1999, we used a method with higher sensitivity to examine all large rivers used as sources of water supply in one prefecture (which we divided into four areas) in western Japan for Cryptosporidium oocysts. One sample was collected at each of 156 sites along 18 rivers, and samples were tested for Cryptosporidium oocysts by immunomagnetic separation. Samples were classified as being obtained on an island with livestock and fishing industries, a densely populated urban area, a western region including farming villages, or a still more rural northern area with agriculture and fishing. Restriction fragment length polymorphism analysis was used for identification of the C. parvum found as the bovine or human type. C. parvum was detected in at least one sample from 13 of the 18 rivers and in 47% (74 of 156) of the samples. One-third to all of the samples from each area contained C. parvum oocysts. The number of C. parvum oocysts per 20 liters of river water varied in the same pattern as the number of cattle kept in the four kinds of areas (as determined by the Mantel extension test). Oocysts isolated were of the bovine type; the C. parvum detected in rivers probably came from cattle kept in that valley. As we had expected, when tested with a more sensitive method, river water in western Japan was found to be greatly contaminated with C. parvum oocysts, as reported in other countries. PMID:11525974

Six faint gamma-ray pulsars seen with the Fermi Large Area Telescope: Towards a sample blending into the background

DOE PAGES

Hou, X.; Smith, D. A.; Guillemot, L.; ...

2014-10-14

Context. Here, GeV gamma-ray pulsations from over 140 pulsars have been characterized using the Fermi Large Area Telescope, enabling improved understanding of the emission regions within the neutron star magnetospheres, and the contributions of pulsars to high energy electrons and diffuse gamma rays in the Milky Way. The first gamma-ray pulsars to be detected were the most intense and/or those with narrow pulses. Aims. As the Fermi mission progresses, progressively fainter objects can be studied. In addition to more distant pulsars (thus probing a larger volume of the Galaxy), or ones in high background regions (thus improving the sampling uniformitymore » across the Galactic plane), we detect pulsars with broader pulses or lower luminosity. Adding pulsars to our catalog with inclination angles that are rare in the observed sample, and/or with lower spindown power, will reduce the bias in the currently known gamma-ray pulsar population. Methods. We use rotation ephemerides derived from radio observations to phase-fold gamma rays recorded by the Fermi Large Area Telescope, to then determine the pulse profile properties. Spectral analysis provides the luminosities and, when the signal-to-noise ratio allows, the cutoff energies. We constrain the pulsar distances by different means in order to minimize the luminosity uncertainties. Results. We present six new gamma-ray pulsars with an eclectic mix of properties. Three are young, and three are recycled. They include the farthest, the lowest power, two of the highest duty-cycle pulsars seen, and only the fourth young gamma-ray pulsar with a radio interpulse. Finally, we discuss the biases existing in the current gamma-ray pulsar catalog, and steps to be taken to mitigate the bias.« less

Super-sample covariance approximations and partial sky coverage

NASA Astrophysics Data System (ADS)

Lacasa, Fabien; Lima, Marcos; Aguena, Michel

2018-04-01

Super-sample covariance (SSC) is the dominant source of statistical error on large scale structure (LSS) observables for both current and future galaxy surveys. In this work, we concentrate on the SSC of cluster counts, also known as sample variance, which is particularly useful for the self-calibration of the cluster observable-mass relation; our approach can similarly be applied to other observables, such as galaxy clustering and lensing shear. We first examined the accuracy of two analytical approximations proposed in the literature for the flat sky limit, finding that they are accurate at the 15% and 30-35% level, respectively, for covariances of counts in the same redshift bin. We then developed a harmonic expansion formalism that allows for the prediction of SSC in an arbitrary survey mask geometry, such as large sky areas of current and future surveys. We show analytically and numerically that this formalism recovers the full sky and flat sky limits present in the literature. We then present an efficient numerical implementation of the formalism, which allows fast and easy runs of covariance predictions when the survey mask is modified. We applied our method to a mask that is broadly similar to the Dark Energy Survey footprint, finding a non-negligible negative cross-z covariance, i.e. redshift bins are anti-correlated. We also examined the case of data removal from holes due to, for example bright stars, quality cuts, or systematic removals, and find that this does not have noticeable effects on the structure of the SSC matrix, only rescaling its amplitude by the effective survey area. These advances enable analytical covariances of LSS observables to be computed for current and future galaxy surveys, which cover large areas of the sky where the flat sky approximation fails.

Reliable and fast quantitative analysis of active ingredient in pharmaceutical suspension using Raman spectroscopy.

PubMed

Park, Seok Chan; Kim, Minjung; Noh, Jaegeun; Chung, Hoeil; Woo, Youngah; Lee, Jonghwa; Kemper, Mark S

2007-06-12

The concentration of acetaminophen in a turbid pharmaceutical suspension has been measured successfully using Raman spectroscopy. The spectrometer was equipped with a large spot probe which enabled the coverage of a representative area during sampling. This wide area illumination (WAI) scheme (coverage area 28.3 mm2) for Raman data collection proved to be more reliable for the compositional determination of these pharmaceutical suspensions, especially when the samples were turbid. The reproducibility of measurement using the WAI scheme was compared to that of using a conventional small-spot scheme which employed a much smaller illumination area (about 100 microm spot size). A layer of isobutyric anhydride was placed in front of the sample vials to correct the variation in the Raman intensity due to the fluctuation of laser power. Corrections were accomplished using the isolated carbonyl band of isobutyric anhydride. The acetaminophen concentrations of prediction samples were accurately estimated using a partial least squares (PLS) calibration model. The prediction accuracy was maintained even with changes in laser power. It was noted that the prediction performance was somewhat degraded for turbid suspensions with high acetaminophen contents. When comparing the results of reproducibility obtained with the WAI scheme and those obtained using the conventional scheme, it was concluded that the quantitative determination of the active pharmaceutical ingredient (API) in turbid suspensions is much improved when employing a larger laser coverage area. This is presumably due to the improvement in representative sampling.

Micrometeoroid and Lunar Secondary Ejecta Flux Measurements: Comparison of Three Acoustic Systems

NASA Technical Reports Server (NTRS)

Corsaro, R. D.; Giovane, F.; Liou, Jer-Chyi; Burtchell, M.; Pisacane, V.; Lagakos, N.; Williams, E.; Stansbery, E.

2010-01-01

This report examines the inherent capability of three large-area acoustic sensor systems and their applicability for micrometeoroids (MM) and lunar secondary ejecta (SE) detection and characterization for future lunar exploration activities. Discussion is limited to instruments that can be fabricated and deployed with low resource requirements. Previously deployed impact detection probes typically have instrumented capture areas less than 0.2 square meters. Since the particle flux decreases rapidly with increased particle size, such small-area sensors rarely encounter particles in the size range above 50 microns, and even their sampling the population above 10 microns is typically limited. Characterizing the sparse dust population in the size range above 50 microns requires a very large-area capture instrument. However it is also important that such an instrument simultaneously measures the population of the smaller particles, so as to provide a complete instantaneous snapshot of the population. For lunar or planetary surface studies, the system constraints are significant. The instrument must be as large as possible to sample the population of the largest MM. This is needed to reliably assess the particle impact risks and to develop cost-effective shielding designs for habitats, astronauts, and critical instrument. The instrument should also have very high sensitivity to measure the flux of small and slow SE particles. is the SE environment is currently poorly characterized, and possess a contamination risk to machinery and personnel involved in exploration. Deployment also requires that the instrument add very little additional mass to the spacecraft. Three acoustic systems are being explored for this application.

Yellow band disease compromises the reproductive output of the Caribbean reef-building coral Montastraea faveolata (Anthozoa, Scleractinia).

PubMed

Weil, Ernesto; Cróquer, Aldo; Urreiztieta, Isabel

2009-11-16

Sexual reproduction is critical to coral population dynamics and the long-term regeneration of coral reefs. Bleaching, disease, and/or anthropogenic-induced tissue/colony loss reduce reproductive output. This is the first attempt to explore the effect of a biotic disease on the reproduction of scleractinian corals. The study aimed to assess the effect of yellow band disease (YBD) on the reproduction of the important Caribbean reef-builder Montastraea faveolata. Tissue samples were collected from diseased, transition, and healthy-looking areas in each of 5 infected colonies and from 5 healthy controls in southwest Puerto Rico. The effect of disease-induced mortality was assessed by collecting samples from the edge and center of surviving small and large, healthy-looking tissue patches from large, previously infected tagged colonies. Fecundity was significantly lower in disease lesions compared to transition and healthy-looking tissues and the controls (99% fewer eggs). Fecundity in transition areas was significantly lower (50%) than in healthy-looking tissues in diseased colonies, which had 23% lower fecundity than control tissues. Although this fecundity drop was not statistically significant, it could indicate a systemic effect of YBD across the colony. Large and small patches had 64 and 84% fewer eggs than controls, respectively, and edge polyps had 97% fewer eggs than those in central control areas. Field observations of the spawning behavior of each tissue area corroborated the histological results. Our results indicate that YBD significantly compromises the reproductive output of M. faveolata, potentially reducing the fitness and consequently, the recovery of this important reef-building species on Caribbean coral reefs.

Large-Area High-Performance Flexible Pressure Sensor with Carbon Nanotube Active Matrix for Electronic Skin.

PubMed

Nela, Luca; Tang, Jianshi; Cao, Qing; Tulevski, George; Han, Shu-Jen

2018-03-14

Artificial "electronic skin" is of great interest for mimicking the functionality of human skin, such as tactile pressure sensing. Several important performance metrics include mechanical flexibility, operation voltage, sensitivity, and accuracy, as well as response speed. In this Letter, we demonstrate a large-area high-performance flexible pressure sensor built on an active matrix of 16 × 16 carbon nanotube thin-film transistors (CNT TFTs). Made from highly purified solution tubes, the active matrix exhibits superior flexible TFT performance with high mobility and large current density, along with a high device yield of nearly 99% over 4 inch sample area. The fully integrated flexible pressure sensor operates within a small voltage range of 3 V and shows superb performance featuring high spatial resolution of 4 mm, faster response than human skin (<30 ms), and excellent accuracy in sensing complex objects on both flat and curved surfaces. This work may pave the road for future integration of high-performance electronic skin in smart robotics and prosthetic solutions.

CENTENNIAL MOUNTAINS WILDERNESS STUDY AREA, MONTANA AND IDAHO.

USGS Publications Warehouse

Witkind, Irving J.; Ridenour, James

1984-01-01

A mineral survey conducted within the Centennial Mountains Wilderness study area in Montana and Idaho showed large areas of probable and substantiated resource potential for phosphate. Byproducts that may be derived from processing the phosphate include vanadium, chromium, uranium, silver, fluorine, and the rare earths, lanthanum and yttrium. Results of a geochemical sampling program suggest that there is little promise for the occurrence of base and precious metals in the area. Although the area contains other nonmetallic deposits, such as coal, building stone, and pumiceous ash they are not considered as mineral resources. There is a probable resource potential for oil and gas and significant amounts may underlie the area around the Peet Creek and Odell Creek anticlines.

Concentration of infectious aquatic rhabdoviruses from freshwater and seawater using ultrafiltration.

PubMed

Grant, Amelia A M; Jakob, Eva; Richard, Jon; Garver, Kyle A

2011-12-01

Infectious hematopoietic necrosis virus (IHNV), viral hemorrhagic septicemia virus, and spring viremia of carp virus were concentrated and detected from freshwater and seawater samples by using hollow-fiber ultrafiltration. Within 60 min, virus in a 50-L freshwater or saltwater sample was concentrated more than 70-fold, and virus retention efficiencies were consistently greater than 88%. Retention efficiency was highly dependent upon concentrations of column blocking and sample stabilization solutions. A large column with a surface area of 1.15 m2 and a filtration capacity of 5-200 L exhibited optimal viral retention when blocked with 2% fetal bovine serum (FBS) and when the samples were supplemented with 0.1% FBS. Conversely, a small column with 100-fold less surface area and a filtering capacity of 0.5-2.0 L was optimized when blocked with 1% FBS and when the samples were supplemented with 0.1% FBS. The optimized ultrafiltration procedure was further validated with water from a tank that contained IHNV-exposed juvenile sockeye salmon Oncorhynchus nerka, resulting in an average virus retention efficiency of 91.6 +/- 4.1% (mean +/- SE). Virus quantification of concentrated samples demonstrated that IHNV shedding in sockeye salmon preceded mortality; shedding of the virus was observed to increase significantly as early as 7 d postchallenge and peaked at day 14, when virus levels reached 4.87 x 10(3) plaque-forming units/mL. We conclude that ultrafiltration is a reliable and effective method for concentrating viable aquatic rhabdoviruses from large volumes of water and has application for the analysis of environmental water samples.

Comparison of two sampling and culture systems for detection of Salmonella enterica in the environment of a large animal hospital.

PubMed

Ruple-Czerniak, A; Bolte, D S; Burgess, B A; Morley, P S

2014-07-01

Nosocomial salmonellosis is an important problem in veterinary hospitals that treat horses and other large animals. Detection and mitigation of outbreaks and prevention of healthcare-associated infections often require detection of Salmonella enterica in the hospital environment. To compare 2 previously published methods for detecting environmental contamination with S. enterica in a large animal veterinary teaching hospital. Hospital-based comparison of environmental sampling techniques. A total of 100 pairs of environmental samples were collected from stalls used to house large animal cases (horses, cows or New World camelids) that were confirmed to be shedding S. enterica by faecal culture. Stalls were cleaned and disinfected prior to sampling, and the same areas within each stall were sampled for the paired samples. One method of detection used sterile, premoistened sponges that were cultured using thioglycolate enrichment before plating on XLT-4 agar. The other method used electrostatic wipes that were cultured using buffered peptone water, tetrathionate and Rappaport-Vassiliadis R10 broths before plating on XLT-4 agar. Salmonella enterica was recovered from 14% of samples processed using the electrostatic wipe sampling and culture procedure, whereas S. enterica was recovered from only 4% of samples processed using the sponge sampling and culture procedure. There was test agreement for 85 pairs of culture-negative samples and 3 pairs of culture-positive samples. However, the remaining 12 pairs of samples with discordant results created significant disagreement between the 2 detection methods (P<0.01). Persistence of Salmonella in the environment of veterinary hospitals can occur even with rigorous cleaning and disinfection. Use of sensitive methods for detection of environmental contamination is critical when detecting and mitigating this problem in veterinary hospitals. These results suggest that the electrostatic wipe sampling and culture method was more sensitive than the sponge sampling and culture method. © 2013 EVJ Ltd.

Characterizing the diversity of coral reef habitats and fish communities found in a UNESCO World Heritage Site: the strategy developed for Lagoons of New Caledonia.

PubMed

Andréfouët, S; Wantiez, L

2010-01-01

Since 1972, the UNESCO "World Heritage Convention" offers an international canvas for conservation and management that targets areas of high cultural and environmental significance. To support the designation of areas within the 36.000 km(2) of New Caledonia coral reefs and lagoons as a World Heritage Site, the natural value and diversity of the proposed zones needed to be demonstrated. To exhaustively identify each configuration of shallow habitats, high resolution remote sensing images were used to select the sampling sites. This optimal scheme resulted in the selection of nearly 1300 sampling sites, and was then simplified to render its application realistic. In the final sampling plan, only the most common or the most remarkable coral zones were selected. Following this selection, in situ habitat and fish surveys were conducted in 2006-2008 in five large areas spanning a 600 km-long latitudinal gradient. Habitats were described using line-intercept transects in parallel with underwater visual census of indicator and commercial coral reef fish species. We report here on the results achieved in terms of: (i) the actual diversity of coral habitats captured by the remote sensing based sampling strategy, (ii) the different reef fish communities captured from the different sites, and (iii) how well they represent New Caledonia diversity. We discuss the possible generalization of this scheme to other sites, in the context of World Heritage Site selection and for other large-scale conservation planning activities. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

An interpolation method for stream habitat assessments

USGS Publications Warehouse

Sheehan, Kenneth R.; Welsh, Stuart A.

2015-01-01

Interpolation of stream habitat can be very useful for habitat assessment. Using a small number of habitat samples to predict the habitat of larger areas can reduce time and labor costs as long as it provides accurate estimates of habitat. The spatial correlation of stream habitat variables such as substrate and depth improves the accuracy of interpolated data. Several geographical information system interpolation methods (natural neighbor, inverse distance weighted, ordinary kriging, spline, and universal kriging) were used to predict substrate and depth within a 210.7-m2 section of a second-order stream based on 2.5% and 5.0% sampling of the total area. Depth and substrate were recorded for the entire study site and compared with the interpolated values to determine the accuracy of the predictions. In all instances, the 5% interpolations were more accurate for both depth and substrate than the 2.5% interpolations, which achieved accuracies up to 95% and 92%, respectively. Interpolations of depth based on 2.5% sampling attained accuracies of 49–92%, whereas those based on 5% percent sampling attained accuracies of 57–95%. Natural neighbor interpolation was more accurate than that using the inverse distance weighted, ordinary kriging, spline, and universal kriging approaches. Our findings demonstrate the effective use of minimal amounts of small-scale data for the interpolation of habitat over large areas of a stream channel. Use of this method will provide time and cost savings in the assessment of large sections of rivers as well as functional maps to aid the habitat-based management of aquatic species.

Photometric Redshifts for the Large-Area Stripe 82X Multiwavelength Survey

NASA Astrophysics Data System (ADS)

Tasnim Ananna, Tonima; Salvato, Mara; Urry, C. Megan; LaMassa, Stephanie M.; STRIPE 82X

2016-06-01

The Stripe 82X survey currently includes 6000 X-ray sources in 31.3 square degrees of XMM-Newton and Chandra X-ray coverage, most of which are AGN. Using a maximum-likelihood approach, we identified optical and infrared counterparts in the SDSS, VHS K-band and WISE W1-band catalogs. 1200 objects which had different best associations in different catalogs were checked by eye. Our most recent paper provided the multiwavelength catalogs for this sample. More than 1000 counterparts have spectroscopic redshifts, either from SDSS spectroscopy or our own follow-up program. Using the extensive multiwavelength data in this field, we provide photometric redshift estimates for most of the remaining sources, which are 80-90% accurate according to the training set. Our sample has a large number of candidates that are very faint in optical and bright in IR. We expect a large fraction of these objects to be the obscured AGN sample we need to complete the census on black hole growth at a range of redshifts.

Galaxy evolution and large-scale structure in the far-infrared. I - IRAS pointed observations

NASA Astrophysics Data System (ADS)

Lonsdale, Carol J.; Hacking, Perry B.

1989-04-01

Redshifts for 66 galaxies were obtained from a sample of 93 60-micron sources detected serendipitously in 22 IRAS deep pointed observations, covering a total area of 18.4 sq deg. The flux density limit of this survey is 150 mJy, 4 times fainter than the IRAS Point Source Catalog (PSC). The luminosity function is similar in shape with those previously published for samples selected from the PSC, with a median redshift of 0.048 for the fainter sample, but shifted to higher space densities. There is evidence that some of the excess number counts in the deeper sample can be explained in terms of a large-scale density enhancement beyond the Pavo-Indus supercluster. In addition, the faintest counts in the new sample confirm the result of Hacking et al. (1989) that faint IRAS 60-micron source counts lie significantly in excess of an extrapolation of the PSC counts assuming no luminosity or density evolution.

Galaxy evolution and large-scale structure in the far-infrared. I. IRAS pointed observations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lonsdale, C.J.; Hacking, P.B.

1989-04-01

Redshifts for 66 galaxies were obtained from a sample of 93 60-micron sources detected serendipitously in 22 IRAS deep pointed observations, covering a total area of 18.4 sq deg. The flux density limit of this survey is 150 mJy, 4 times fainter than the IRAS Point Source Catalog (PSC). The luminosity function is similar in shape with those previously published for samples selected from the PSC, with a median redshift of 0.048 for the fainter sample, but shifted to higher space densities. There is evidence that some of the excess number counts in the deeper sample can be explained inmore » terms of a large-scale density enhancement beyond the Pavo-Indus supercluster. In addition, the faintest counts in the new sample confirm the result of Hacking et al. (1989) that faint IRAS 60-micron source counts lie significantly in excess of an extrapolation of the PSC counts assuming no luminosity or density evolution. 81 refs.« less

Galaxy evolution and large-scale structure in the far-infrared. I - IRAS pointed observations

NASA Technical Reports Server (NTRS)

Lonsdale, Carol J.; Hacking, Perry B.

1989-01-01

Redshifts for 66 galaxies were obtained from a sample of 93 60-micron sources detected serendipitously in 22 IRAS deep pointed observations, covering a total area of 18.4 sq deg. The flux density limit of this survey is 150 mJy, 4 times fainter than the IRAS Point Source Catalog (PSC). The luminosity function is similar in shape with those previously published for samples selected from the PSC, with a median redshift of 0.048 for the fainter sample, but shifted to higher space densities. There is evidence that some of the excess number counts in the deeper sample can be explained in terms of a large-scale density enhancement beyond the Pavo-Indus supercluster. In addition, the faintest counts in the new sample confirm the result of Hacking et al. (1989) that faint IRAS 60-micron source counts lie significantly in excess of an extrapolation of the PSC counts assuming no luminosity or density evolution.

Results of preliminary reconnaissance trip to determine the presence of wetlands in wet forest habitats on the Island of Hawaii as part of the Hawaii Geothermal Project, October 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wakeley, J.S.; Sprecher, S.W.; Lichvar, R.

1994-02-25

In October 1993, the authors sampled soils, vegetation, and hydrology at eight sites representing a range of substrates, elevations, soil types, and plant community types within rainforest habitats on the Island of Hawaii. Their purpose was to determine whether any of these habitats were wetlands according to the 1987 Corps of Engineers Wetlands Delineation Manual. None of the rainforest habitats they sampled was wetland in its entirety. However, communities established on pahoehoe lava flows contained scattered wetlands in depressions and folds in the lava, where water could accumulate. Therefore, large construction projects, such as that associated with proposed geothermal energymore » development in the area, have the potential to impact a significant number and/or area of wetlands. To estimate those impacts more accurately, they present a supplementary scope of work and cost estimate for additional sampling in the proposed geothermal project area.« less

Variation of volatile compounds among wheat varieties and landraces.

PubMed

Starr, G; Petersen, M A; Jespersen, B M; Hansen, Å S

2015-05-01

Analysis of volatile compounds was performed on 81 wheat varieties and landraces, grown under controlled greenhouse conditions, in order to investigate the possibility of differentiating wheat varieties according to their volatile compound profiles. Volatile compounds from wheat samples were extracted by dynamic headspace extraction and analysed by gas chromatography-mass spectrometry. Seventy-two volatile compounds were identified in the wheat samples. Multivariate analysis of the data showed a large diversity in volatile profiles between samples. Differences occurred between samples from Austria compared to British, French and Danish varieties. Landraces were distinguishable from modern varieties and they were characterised by higher averaged peak areas for esters, alcohols, and some furans. Modern varieties were characterised by higher averaged peak areas for terpenes, pyrazines and straight-chained aldehydes. Differences in volatile profiles are demonstrated between wheat samples for the first time, based on variety. These results are significant to plant breeders and commercial users of wheat. Copyright © 2014 Elsevier Ltd. All rights reserved.

VizieR Online Data Catalog: Large area KX quasar catalogue (Maddox+, 2012)

NASA Astrophysics Data System (ADS)

Maddox, N.; Hewett, P. C.; Peroux, C.; Nestor, D. B.; Wisotzki, L.

2013-05-01

In order to maximize the dynamic range of the survey in absolute magnitude at fixed redshift, while ensuring adequate sampling of the brightest quasars, a 'wedding cake' survey geometry is adopted. Thus, the entire survey area is complete to the brightest limits, with a smaller subregion complete to fainter magnitudes and the smallest subregion complete to the faintest limits. Observations of the survey area utilized four telescopes (NTT, VLT, CA 2.2m and CA 3.5m) over three observing semesters between 2009 May and 2010 July. (2 data files).

Large Area Crop Inventory Experiment (LACIE). Development of procedure M for multicrop inventory, with tests of a spring-wheat configuration

NASA Technical Reports Server (NTRS)

Horvath, R. (Principal Investigator); Cicone, R.; Crist, E.; Kauth, R. J.; Lambeck, P.; Malila, W. A.; Richardson, W.

1979-01-01

The author has identified the following significant results. An outgrowth of research and development activities in support of LACIE was a multicrop area estimation procedure, Procedure M. This procedure was a flexible, modular system that could be operated within the LACIE framework. Its distinctive features were refined preprocessing (including spatially varying correction for atmospheric haze), definition of field like spatial features for labeling, spectral stratification, and unbiased selection of samples to label and crop area estimation without conventional maximum likelihood classification.

Amorphous layer formation in Al86.0Co7.6Ce6.4 glass-forming alloy by large-area electron beam irradiation

NASA Astrophysics Data System (ADS)

Li, C. L.; Murray, J. W.; Voisey, K. T.; Clare, A. T.; McCartney, D. G.

2013-09-01

Amorphous Al-Co-Ce alloys are of interest because of their resistance to corrosion, but high cooling rates are generally required to suppress the formation of crystalline phases. In this study, the surface of a bulk crystalline Al-Co-Ce alloy of a glass-forming composition was treated using large area electron beam (LAEB) irradiation. Scanning electron microscopy shows that, compared to the microstructure of the original crystalline material, the treated surface exhibits greatly improved microstructural and compositional uniformity. Glancing angle X-ray diffraction conducted on the surface of treated samples indicates the formation of the amorphous phase following 25 and 50 pulses at 35 kV cathode voltage. However, when the samples are treated with 100 and 150 pulses at 35 kV cathode voltage of electron beam irradiation, the treated layer comprises localised crystalline regions in an amorphous matrix. In addition, the formation of cracks in the treated layer is found to be localised around the Al8Co2Ce phase in the bulk material. Overall, crack length per unit area had no clear change with an increase in the number of pulses.

MUTAGENIC PROPERTIES OF RIVER WATERS FLOWING THROUGH BIG CITY AREAS IN NORTH AMERICA

EPA Science Inventory

The hanging technique using Blue rayon, which specifically adsorbs mutagens with multicyclic planer structures, has advantages over the conventional method of bringing-large volumes of water back to the laboratory for extraction. Therefore, the analysis of many samples from remot...

Synthesis of porous NiO/CeO2 hybrid nanoflake arrays as a platform for electrochemical biosensing

NASA Astrophysics Data System (ADS)

Cui, Jiewu; Luo, Jinbao; Peng, Bangguo; Zhang, Xinyi; Zhang, Yong; Wang, Yan; Qin, Yongqiang; Zheng, Hongmei; Shu, Xia; Wu, Yucheng

2015-12-01

Porous NiO/CeO2 hybrid nanoflake arrays fabricated by a facile hydrothermal method were employed as substrates for electrochemical biosensors. The resulting NiO/CeO2 hybrid nanoflake arrays with a large specific surface area and good biocompatibility presented an excellent platform for electrochemical biosensing.Porous NiO/CeO2 hybrid nanoflake arrays fabricated by a facile hydrothermal method were employed as substrates for electrochemical biosensors. The resulting NiO/CeO2 hybrid nanoflake arrays with a large specific surface area and good biocompatibility presented an excellent platform for electrochemical biosensing. Electronic supplementary information (ESI) available: Optical photographs of the as-prepared samples, SEM, TEM, EDS, XRD and BET data of the samples are presented, I-t curves of glucose biosensors based on NiO and NiO/CeO2 NFAs, EIS results of different electrodes. See DOI: 10.1039/c5nr05924k

Genetic analysis of floating Enteromorpha prolifera in the Yellow Sea with AFLP marker

NASA Astrophysics Data System (ADS)

Liu, Cui; Zhang, Jing; Sun, Xiaoyu; Li, Jian; Zhang, Xi; Liu, Tao

2011-09-01

Extremely large accumulation of green algae Enteromorpha prolifera floated along China' coastal region of the Yellow Sea ever since the summer of 2008. Amplified Fragment Length Polymorphism (AFLP) analysis was applied to assess the genetic diversity and relationships among E. prolifera samples collected from 9 affected areas of the Yellow Sea. Two hundred reproducible fragments were generated with 8 AFLP primer combinations, of which 194 (97%) were polymorphic. The average Nei's genetic diversity, the coefficiency of genetic differentiation (Gst), and the average gene flow estimated from Gst in the 9 populations were 0.4018, 0.6404 and 0.2807 respectively. Cluster analysis based on the unweighed pair group method with arithmetic averages (UPGMA) showed that the genetic relationships within one population or among different populations were all related to their collecting locations and sampling time. Large genetic differentiation was detected among the populations. The E. prolifera originated from different areas and were undergoing a course of mixing.

Search for Cosmic-Ray Electron and Positron Anisotropies with Seven Years of Fermi Large Area Telescope Data.

PubMed

Abdollahi, S; Ackermann, M; Ajello, M; Albert, A; Atwood, W B; Baldini, L; Barbiellini, G; Bellazzini, R; Bissaldi, E; Bloom, E D; Bonino, R; Bottacini, E; Brandt, T J; Bruel, P; Buson, S; Caragiulo, M; Cavazzuti, E; Chekhtman, A; Ciprini, S; Costanza, F; Cuoco, A; Cutini, S; D'Ammando, F; de Palma, F; Desiante, R; Digel, S W; Di Lalla, N; Di Mauro, M; Di Venere, L; Donaggio, B; Drell, P S; Favuzzi, C; Focke, W B; Fukazawa, Y; Funk, S; Fusco, P; Gargano, F; Gasparrini, D; Giglietto, N; Giordano, F; Giroletti, M; Green, D; Guiriec, S; Harding, A K; Jogler, T; Jóhannesson, G; Kamae, T; Kuss, M; Larsson, S; Latronico, L; Li, J; Longo, F; Loparco, F; Lubrano, P; Magill, J D; Malyshev, D; Manfreda, A; Mazziotta, M N; Meehan, M; Michelson, P F; Mitthumsiri, W; Mizuno, T; Moiseev, A A; Monzani, M E; Morselli, A; Negro, M; Nuss, E; Ohsugi, T; Omodei, N; Paneque, D; Perkins, J S; Pesce-Rollins, M; Piron, F; Pivato, G; Principe, G; Rainò, S; Rando, R; Razzano, M; Reimer, A; Reimer, O; Sgrò, C; Simone, D; Siskind, E J; Spada, F; Spandre, G; Spinelli, P; Strong, A W; Tajima, H; Thayer, J B; Torres, D F; Troja, E; Vandenbroucke, J; Zaharijas, G; Zimmer, S

2017-03-03

The Large Area Telescope on board the Fermi Gamma-ray Space Telescope has collected the largest ever sample of high-energy cosmic-ray electron and positron events since the beginning of its operation. Potential anisotropies in the arrival directions of cosmic-ray electrons or positrons could be a signature of the presence of nearby sources. We use almost seven years of data with energies above 42 GeV processed with the Pass 8 reconstruction. The present data sample can probe dipole anisotropies down to a level of 10^{-3}. We take into account systematic effects that could mimic true anisotropies at this level. We present a detailed study of the event selection optimization of the cosmic-ray electrons and positrons to be used for anisotropy searches. Since no significant anisotropies have been detected on any angular scale, we present upper limits on the dipole anisotropy. The present constraints are among the strongest to date probing the presence of nearby young and middle-aged sources.

Diversity of epothilone producers among Sorangium strains in producer-positive soil habitats.

PubMed

Li, Shu-Guang; Zhao, Lin; Han, Kui; Li, Peng-Fei; Li, Zhi-Feng; Hu, Wei; Liu, Hong; Wu, Zhi-Hong; Li, Yue-Zhong

2014-03-01

Large-scale surveys show that the anti-tumour compounds known as epothilones are produced by only a small proportion of Sorangium strains, thereby greatly hampering the research and development of these valuable compounds. In this study, to investigate the niche diversity of epothilone-producing Sorangium strains, we re-surveyed four soil samples where epothilone producers were previously found. Compared with the < 2.5% positive strains collected from different places, epothilone producers comprised 25.0-75.0% of the Sorangium isolates in these four positive soil samples. These sympatric epothilone producers differed not only in their 16S rRNA gene sequences and morphologies but also in their production of epothilones and biosynthesis genes. A further exploration of 14 soil samples collected from a larger area around a positive site showed a similar high positive ratio of epothilone producers among the Sorangium isolates. The present results suggest that, in an area containing epothilone producers, the long-term genetic variations and refinements resulting from selective pressure form a large reservoir of epothilone-producing Sorangium strains with diverse genetic compositions. © 2013 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Dispersive liquid-liquid microextraction for the determination of nitrophenols in soils by microvial insert large volume injection-gas chromatography-mass spectrometry.

PubMed

Cacho, J I; Campillo, N; Viñas, P; Hernández-Córdoba, M

2016-07-22

A rapid and sensitive procedure for the determination of six NPs in soils by gas chromatography and mass spectrometry (GC-MS) is proposed. Ultrasound assisted extraction (UAE) is used for NP extraction from soil matrices to an organic solvent, while the environmentally friendly technique dispersive liquid-liquid microextraction (DLLME) is used for the preconcentration of the resulting UAE extracts. NPs were derivatized by applying an "in-situ" acetylation procedure, before being injected into the GC-MS system using microvial insert large volume injection (LVI). Several parameters affecting UAE, DLLME, derivatization and injection steps were investigated. The optimized procedure provided recoveries of 86-111% from spiked samples. Precision values of the procedure (expressed as relative standard deviation, RSD) lower than 12%, and limits of quantification ranging from 1.3 to 2.6ngg(-1), depending on the compound, were obtained. Twenty soil samples, obtained from military, industrial and agricultural areas, were analyzed by the proposed method. Two of the analytes were quantified in two of the samples obtained from industrial areas, at concentrations in the 4.8-9.6ngg(-1) range. Copyright © 2016 Elsevier B.V. All rights reserved.

Ecosystem services from converted land: the importance of tree cover in Amazonian pastures

USGS Publications Warehouse

Barrett, Kirsten; Valentim, Judson; Turner, B. L.

2013-01-01

Deforestation is responsible for a substantial fraction of global carbon emissions and changes in surface energy budgets that affect climate. Deforestation losses include wildlife and human habitat, and myriad forest products on which rural and urban societies depend for food, fiber, fuel, fresh water, medicine, and recreation. Ecosystem services gained in the transition from forests to pasture and croplands, however, are often ignored in assessments of the impact of land cover change. The role of converted lands in tropical areas in terms of carbon uptake and storage is largely unknown. Pastures represent the fastest-growing form of converted land use in the tropics, even in some areas of rapid urban expansion. Tree biomass stored in these areas spans a broad range, depending on tree cover. Trees in pasture increase carbon storage, provide shade for cattle, and increase productivity of forage material. As a result, increasing fractional tree cover can provide benefits land managers as well as important ecosystem services such as reducing conversion pressure on forests adjacent to pastures. This study presents an estimation of fractional tree cover in pasture in a dynamic region on the verge of large-scale land use change. An appropriate sampling interval is established for similar studies, one that balances the need for independent samples of sufficient number to characterize a pasture in terms of fractional tree cover. This information represents a useful policy tool for government organizations and NGOs interested in encouraging ecosystem services on converted lands. Using high spatial resolution remotely sensed imagery, fractional tree cover in pasture is quantified for the municipality of Rio Branco, Brazil. A semivariogram and devolving spatial resolution are employed to determine the coarsest sampling interval that may be used, minimizing effects of spatial autocorrelation. The coarsest sampling interval that minimizes spatial dependence was about 22 m. The area-weighted fractional tree cover for the study area was 1.85 %, corrected for a slight bias associated with the coarser sampling resolution. The pastures sampled for fractional tree cover were divided between ‘high’ and ‘low’ tree cover, which may be the result of intentional incorporation of arboreal species in pasture. Further research involving those ranchers that have a higher fractional tree cover may indicate ways to promote the practice on a broader scale in the region.

Thickness determination of large-area films of yttria-stabilized zirconia produced by pulsed laser deposition

NASA Astrophysics Data System (ADS)

Pryds, N.; Toftmann, B.; Bilde-Sørensen, J. B.; Schou, J.; Linderoth, S.

2006-04-01

Films of yttria-stabilized zirconia (YSZ) on a polished silicon substrate of diameter up to 125 mm have been produced in a large-area pulsed laser deposition (PLD) setup under typical PLD conditions. The film thickness over the full film area has been determined by energy-dispersive X-ray spectrometry in a scanning electron microscope (SEM) with use of a method similar to one described by Bishop and Poole. The attenuation of the electron-induced X-rays from the Si wafer by the film was monitored at a number of points along a diameter and the thickness was determined by Monte Carlo simulations of the attenuation for various values of film thickness with the program CASINO. These results have been compared with direct measurements in the SEM of the film thickness on a cross-section on one of the wafers. The results of these measurements demonstrate the ability of this technique to accurately determine the thickness of a large film, i.e. up to diameters of 125 mm, in a relatively short time, without destroying the substrate, without the need of a standard sample and without the need of a flat substrate. We have also demonstrated that by controlling the deposition parameters large-area YSZ films with uniform thickness can be produced.

In-stand scenic beauty of variable retention harvests and mature forests in the U.S. Pacific Northwest: the effects of basal area, density, retention pattern and down wood

Treesearch

R.G. Ribe

2009-01-01

Tensions between amenity- and timber-based economies in the U.S. and Canadian Pacific Northwest motivated a study of scenic beauty inside mature forests and timber harvests. A diverse sample of regional forests, measures of forest structure, and large, representative samples of photographs and public judges were employed to measure scenic beauty inside unharvested...

Annual design-based estimation for the annualized inventories of forest inventory and analysis: sample size determination

Treesearch

Hans T. Schreuder; Jin-Mann S. Lin; John Teply

2000-01-01

The Forest Inventory and Analysis units in the USDA Forest Service have been mandated by Congress to go to an annualized inventory where a certain percentage of plots, say 20 percent, will be measured in each State each year. Although this will result in an annual sample size that will be too small for reliable inference for many areas, it is a sufficiently large...

Population genetic structure of Attalea vitrivir Zona (Arecaceae) in fragmented areas of southeast Brazil.

PubMed

Santos, R R M; Cavallari, M M; Pimenta, M A S; Abreu, A G; Costa, M R; Guedes, M L

2015-06-11

Attalea vitrivir Zona (synonym Orbignya oleifera) is one of the six species of Arecaceae known as "babassu". This species is used to make cosmetics, food, and detergents due to the high concentration of oil in the seeds. It is found only in fragmented areas of southern Bahia State and northern Minas Gerais State, southeast Brazil, and this fragmentation has affected both its ecological and genetic characteristics. We evaluated the genetic diversity and population genetic structure of A. vitrivir in six areas of two different regions at the extremes of its geographical range, in order to gain a better understanding of the factors that affect the distribution and partitioning of its diversity. Nine inter simple sequence repeat (ISSR) markers amplified 74 polymorphic bands, resulting in large diversity values (Shannon diversity index, 0.37-0.47; intrapopulation genetic diversity, 0.25-0.34). Analysis of molecular variance (AMOVA) revealed considerable differentiation between sampling sites (30.03%) and regions (12.08%), although most of the diversity was observed within sampling sites (69%). Further differentiation between sampling sites was noted more in the northern region than in the southern region, highlighting the genetic connectivity between the sampling sites within Rio Pandeiros Environmental Protection Area (southern region). The identification of two distinct genetic clusters (K = 2) corresponded to the northern and southern regions, and corroborated the AMOVA results. We suggest that the northern area, outside Rio Pandeiros Environmental Protection Area, must be included in future management plans for this species.

Nutrients in Streams and Rivers Across the Nation -- 1992-2001

USGS Publications Warehouse

Mueller, David K.; Spahr, Norman E.

2006-01-01

Nutrient compounds of nitrogen and phosphorus were investigated in streams and rivers sampled as part of the U.S. Geological Survey National Water-Quality Assessment (NAWQA) Program. Nutrient data were collected in 20 NAWQA study units during 1992-95, 16 study units during 1996-98, and 15 study units during 1999-2001. To facilitate comparisons among sampling sites with variable sampling frequency, daily loads were determined by using regression models that relate constituent transport to streamflow and time. Model results were used to compute mean annual loads, yields, and concentrations of ammonia, nitrate, total nitrogen, orthophosphate, and total phosphorus, which were compared among stream and river sampling sites. Variations in the occurrence and distribution of nutrients in streams and rivers on a broad national scale reflect differences in the sources of nutrient inputs to the upstream watersheds and in watershed characteristics that affect movement of those nutrients. Sites were classified by watershed size and by land use in the upstream watershed: agriculture, urban, and undeveloped (forest or rangeland). Selection of NAWQA urban sites was intended to avoid effects of major wastewater-treatment plants and other point sources, but in some locations this was not feasible. Nutrient concentrations and yields generally increased with anthropogenic development in the watershed. Median concentrations and yields for all constituents at sites downstream from undeveloped areas were less than at sites downstream from agricultural or urban areas. Concentrations of ammonia, orthophosphate, and total phosphorus at agricultural and urban sites were not significantly different; however, concentrations of nitrate and total nitrogen were higher at agricultural than at urban sites. Total nitrogen concentrations at agricultural sites were higher in areas of high nitrogen input or enhanced transport, such as irrigation or artificial drainage that can rapidly move water from cropland to streams (Midwest, Northern Plains, and western areas of the United States). Concentrations were lower in the Southeast, where more denitrification occurs during transport of nitrogen compounds in shallow ground water. At urban sites, high concentrations of ammonia and orthophosphate were more prevalent downstream from wastewater-treatment plants. At sites with large watersheds and high mean-annual streamflow ('large-watershed' sites), concentrations of most nutrients were significantly less than at sites downstream from agricultural or urban areas. Total nitrogen concentrations at large-watershed sites were higher in Midwest agricultural areas and lower in the Western United States, where agricultural and urban development is less extensive. Total phosphorus concentrations at large-watershed sites were higher in areas of greater potential erosion and low overall runoff such as the arid areas in the West. Although not as distinct as seasonal patterns of streamflow, geographic patterns of seasonally high and low concentrations of total nitrogen and total phosphorus were identified in the data. Seasonal patterns in concentrations of total nitrogen generally mirror seasonal patterns in streamflow in the humid Eastern United States but are inverse to seasonal patterns in streamflow in the semiarid interior West. Total phosphorus concentrations typically have the opposite regional relation with streamflow; high concentrations coincide with high streamflows in the interior West. In the NAWQA Program, sites downstream from relatively undeveloped areas were selected to provide a baseline for comparison to sites with potential effects of urban development and agriculture. Concentrations of nitrate, total nitrogen, and total phosphorus at NAWQA undeveloped sites were found to be greater than values reported by other studies for conditions of essentially no development (background conditions). Concentrations at NAWQA undeveloped sites represent conditions

PAH and PCB in the Baltic -- A budget approach including fluxes, occurrence and concentration variability in air, suspended and settling particulates in water, surface sediments and river water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broman, D.; Axelman, J.; Bandh, C.

In order to study the fate and occurrence of two groups of hydrophobic compounds in the Baltic aquatic environment a large number of samples were collected from the southern Baltic proper to the northern Bothnian Bay for the analyses of polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs). The following sample matrices were collected; bottom surface sediments (0--1 cm, collected with gravity corer), settling particulate matter (collected with sediment traps), open water samples and over water samples (suspended particulates and dissolved fraction sampled by filtration) and air samples (aerosols and vapor phase sampled by filtration). All samples (except over watermore » and air) were collected at open sea in the Baltic. The analyses results have been used to make a model approach on the whole Baltic and to elucidate different aspects of the behavior of PAHs and PCBs in the Baltic, such as the occurrence of the compounds in water and sediment, the total content as well as the concentration variabilities over such a large geographical area, Further, the data on settling particulate matter as well as the air concentration data were used to estimate the total fluxes of PAHs and PCBs to the bottoms of the Baltic and t o the total water area of the Baltic, respectively. Further, data on the PAH and PCB content in river water from four major rivers provides rough estimates of the riverine input to the Baltic. The dynamics of PAHs and PCBs within the water mass have also been studied in terms of settling velocities and residence times in the water mass for these type of compounds in the open Baltic.« less

Geo-spatial aspects of acceptance of illegal hunting of large carnivores in Scandinavia.

PubMed

Gangaas, Kristin E; Kaltenborn, Bjørn P; Andreassen, Harry P

2013-01-01

Human-carnivore conflicts are complex and are influenced by: the spatial distribution of the conflict species; the organisation and intensity of management measures such as zoning; historical experience with wildlife; land use patterns; and local cultural traditions. We have used a geographically stratified sampling of social values and attitudes to provide a novel perspective to the human - wildlife conflict. We have focused on acceptance by and disagreements between residents (measured as Potential Conflict Index; PCI) towards illegal hunting of four species of large carnivores (bear, lynx, wolf, wolverine). The study is based on surveys of residents in every municipality in Sweden and Norway who were asked their opinion on illegal hunting. Our results show how certain social values are associated with acceptance of poaching, and how these values differ geographically independent of carnivore abundance. Our approach differs from traditional survey designs, which are often biased towards urban areas. Although these traditional designs intend to be representative of a region (i.e. a random sample from a country), they tend to receive relatively few respondents from rural areas that experience the majority of conflict with carnivores. Acceptance of poaching differed significantly between Norway (12.7-15.7% of respondents) and Sweden (3.3-4.1% of respondents). We found the highest acceptance of illegal hunting in rural areas with free-ranging sheep and strong hunting traditions. Disagreements between residents (as measured by PCI) were highest in areas with intermediate population density. There was no correlation between carnivore density and either acceptance of illegal hunting or PCI. A strong positive correlation between acceptance of illegal hunting and PCI showed that areas with high acceptance of illegal hunting are areas with high potential conflict between people. Our results show that spatially-stratified surveys are required to reveal the large scale patterns in social dynamics of human-wildlife conflicts.

Use of Nanostructures in Fabrication of Large Scale Electrochemical Film

NASA Astrophysics Data System (ADS)

Chen, Chien Chon; Chen, Shih Hsun; Shyu, Sheang Wen; Hsieh, Sheng Jen

Control of electrochemical parameters when preparing small-scale samples for academic research is not difficult. In mass production environments, however, maintenance of constant current density and temperature become a critical issue. This article describes the design of several molds for large work pieces. These molds were designed to maintain constant current density and to facilitate the occurrence of electrochemical reactions in designated areas. Large-area thin films with fine nanostructure were successfully prepared using the designed electrochemical molds and containers. In addition, current density and temperature could be controlled well. This electrochemical system has been verified in many experimental operations, including etching of Al surfaces; electro-polishing of Al, Ti and stainless steel; and fabrication of anodic alumina oxide (AAO), Ti-TiO2 interference membrane, TiO2 nanotubes, AAO-TiO2 nanotubes, Ni nanowires and porous tungsten

Ground-water quality beneath irrigated agriculture in the central High Plains aquifer, 1999-2000

USGS Publications Warehouse

Bruce, Breton W.; Becker, Mark F.; Pope, Larry M.; Gurdak, Jason J.

2003-01-01

In 1999 and 2000, 30 water-quality monitoring wells were installed in the central High Plains aquifer to evaluate the quality of recently recharged ground water in areas of irrigated agriculture and to identify the factors affecting ground-water quality. Wells were installed adjacent to irrigated agricultural fields with 10- or 20-foot screened intervals placed near the water table. Each well was sampled once for about 100 waterquality constituents associated with agricultural practices. Water samples from 70 percent of the wells (21 of 30 sites) contained nitrate concentrations larger than expected background concentrations (about 3 mg/L as N) and detectable pesticides. Atrazine or its metabolite, deethylatrazine, were detected with greater frequency than other pesticides and were present in all 21 samples where pesticides were detected. The 21 samples with detectable pesticides also contained tritium concentrations large enough to indicate that at least some part of the water sample had been recharged within about the last 50 years. These 21 ground-water samples are considered to show water-quality effects related to irrigated agriculture. The remaining 9 groundwater samples contained no pesticides, small tritium concentrations, and nitrate concentrations less than 3.45 milligrams per liter as nitrogen. These samples are considered unaffected by the irrigated agricultural land-use setting. Nitrogen isotope ratios indicate that commercial fertilizer was the dominant source of nitrate in 13 of the 21 samples affected by irrigated agriculture. Nitrogen isotope ratios for 4 of these 21 samples were indicative of an animal waste source. Dissolved-solids concentrations were larger in samples affected by irrigated agriculture, with large sulfate concentrations having strong correlation with large dissolved solids concentrations in these samples. A strong statistical correlation is shown between samples affected by irrigated agriculture and sites with large rates of pesticide and nitrogen applications and shallow depths to ground water.

Soil microbial abundance, activity and diversity response in two different altitude-adapted plant communities affected by wildfire in Sierra Nevada National Park (Granada, Spain)

NASA Astrophysics Data System (ADS)

Bárcenas-Moreno, Gema; Zavala, Lorena; Jordan, Antonio; Bååth, Erland; Mataix-Beneyto, Jorge

2013-04-01

Plant communities can play an important role in fire severity and post-fire ecosystem recovery due to their role as combustible and different plant-soil microorganisms interactions. Possible differences induced by plant and microorganisms response after fire could affect the general ecosystem short and long-term response and its sustainability. The main objective of this work was the evaluation of the effect of wildfire on soil microbial abundance, activity and diversity in two different plant communities associated to different altitudes in Sierra Nevada National Park (Granada, Spain). Samples were collected in two areas located on the Sierra Nevada Mountain between 1700 and 2000 m above sea level which were affected by a large wildfire in 2005. Two samplings were carried out 8 and 20 months after fire and samples were collected in both burned and unburned (control) zones in each plant community area. Area A is located at 1700m and it is formed by Quercus rotundifolia forest while area B is located at 2000 m altitude and is composed of alpine vegetation formed by creeping bearing shrubs. Microbial biomass measured by Fumigation-Extraction method followed the same trend in both areas showing slight and no significant differences between burned and unburned area during the study period while viable and cultivable bacteria abundance were markedly higher in fire affected samples than in the control ones in both samplings. Viable and cultivable filamentous fungi had different behavior depending of plant vegetation community studied showing no differences between burned and unburned area in area A while was significantly higher in burned samples than in the control ones in area B. Microbial activity monitoring with soil microbial respiration appears to had been affected immediately after fire since microbial respiration was lower in burned samples from area A than in unburned one only 8 months after fire and no significant differences were observed between burned and unburned samples in area B. Soil microbial community composition studied by Principal Component Analyses (PCA) of the PLFA pattern revealed both fire and seasonal effects. General overview of the results could lead to think in a slight negative or even positive effect of fire on soil microbial parameters studied, mainly in zone B. Nevertheless if we calculate the ratio between C-biomass and organic-C we find lower ratio in fire-affected samples than in the control ones in both areas, showing the most marked effect on area B which remain with this tendency 20 months after fire. Acknowledgements: This research was supported by the CICYT co-financed FEDER project CGL2006-11107-C02-01/BOS. We are grateful for the Sierra Nevada National Park support during the study.

Speciation Mapping of Environmental Samples Using XANES Imaging

EPA Science Inventory

Fast X-ray detectors with large solid angles and high dynamic ranges open the door to XANES imaging, in which millions of spectra are collected to image the speciation of metals at micrometre resolution, over areas up to several square centimetres. This paper explores how such mu...

Eutrophication monitoring for Lake Superior’s Chequamegon Bay before and after large summer storms

EPA Science Inventory

A priority for the Lake Superior CSMI was to identify susceptible nearshore eutrophication areas. We developed an integrated sampling design to collect baseline data for Lake Superior’s Chequamegon Bay to understand how nearshore physical processes and tributary loading rel...

Spatial Distribution of Stony Desertification and Key Influencing Factors on Different Sampling Scales in Small Karst Watersheds

PubMed Central

Zhang, Zhenming; Zhou, Yunchao; Wang, Shijie

2018-01-01

Karst areas are typical ecologically fragile areas, and stony desertification has become the most serious ecological and economic problems in these areas worldwide as well as a source of disasters and poverty. A reasonable sampling scale is of great importance for research on soil science in karst areas. In this paper, the spatial distribution of stony desertification characteristics and its influencing factors in karst areas are studied at different sampling scales using a grid sampling method based on geographic information system (GIS) technology and geo-statistics. The rock exposure obtained through sampling over a 150 m × 150 m grid in the Houzhai River Basin was utilized as the original data, and five grid scales (300 m × 300 m, 450 m × 450 m, 600 m × 600 m, 750 m × 750 m, and 900 m × 900 m) were used as the subsample sets. The results show that the rock exposure does not vary substantially from one sampling scale to another, while the average values of the five subsamples all fluctuate around the average value of the entire set. As the sampling scale increases, the maximum value and the average value of the rock exposure gradually decrease, and there is a gradual increase in the coefficient of variability. At the scale of 150 m × 150 m, the areas of minor stony desertification, medium stony desertification, and major stony desertification in the Houzhai River Basin are 7.81 km2, 4.50 km2, and 1.87 km2, respectively. The spatial variability of stony desertification at small scales is influenced by many factors, and the variability at medium scales is jointly influenced by gradient, rock content, and rock exposure. At large scales, the spatial variability of stony desertification is mainly influenced by soil thickness and rock content. PMID:29652811

Spatial Distribution of Stony Desertification and Key Influencing Factors on Different Sampling Scales in Small Karst Watersheds.

PubMed

Zhang, Zhenming; Zhou, Yunchao; Wang, Shijie; Huang, Xianfei

2018-04-13

Karst areas are typical ecologically fragile areas, and stony desertification has become the most serious ecological and economic problems in these areas worldwide as well as a source of disasters and poverty. A reasonable sampling scale is of great importance for research on soil science in karst areas. In this paper, the spatial distribution of stony desertification characteristics and its influencing factors in karst areas are studied at different sampling scales using a grid sampling method based on geographic information system (GIS) technology and geo-statistics. The rock exposure obtained through sampling over a 150 m × 150 m grid in the Houzhai River Basin was utilized as the original data, and five grid scales (300 m × 300 m, 450 m × 450 m, 600 m × 600 m, 750 m × 750 m, and 900 m × 900 m) were used as the subsample sets. The results show that the rock exposure does not vary substantially from one sampling scale to another, while the average values of the five subsamples all fluctuate around the average value of the entire set. As the sampling scale increases, the maximum value and the average value of the rock exposure gradually decrease, and there is a gradual increase in the coefficient of variability. At the scale of 150 m × 150 m, the areas of minor stony desertification, medium stony desertification, and major stony desertification in the Houzhai River Basin are 7.81 km², 4.50 km², and 1.87 km², respectively. The spatial variability of stony desertification at small scales is influenced by many factors, and the variability at medium scales is jointly influenced by gradient, rock content, and rock exposure. At large scales, the spatial variability of stony desertification is mainly influenced by soil thickness and rock content.

Organic Compounds and Trace Elements in Fish Tissue and Bed Sediment in the Delaware River Basin, New Jersey, Pennsylvania, New York, and Delaware, 1998-2000

USGS Publications Warehouse

Romanok, Kristin M.; Fischer, Jeffrey M.; Riva-Murray, Karen; Brightbill, Robin; Bilger, Michael

2006-01-01

As part of the National Water-Quality Assessment (NAWQA) program activities in the Delaware River Basin (DELR), samples of fish tissue from 21 sites and samples of bed sediment from 35 sites were analyzed for a suite of organic compounds and trace elements. The sampling sites, within subbasins ranging in size from 11 to 600 square miles, were selected to represent 5 main land-use categories in the DELR -forest, low-agricultural, agricultural, urban, and mixed use. Samples of both fish tissue and bed sediment were also collected from 4 'large-river' sites that represented drainage areas ranging from 1,300 to 6,800 square miles, areas in which the land is used for a variety of purposes. One or more of the organochlorine compounds-DDT and chlordane metabolites, polychlorinated biphenyls (total PCBs), and dieldrin- were detected frequently in samples collected over a wide geographic area. One or more of these compounds were detected in fish-tissue samples from 92 percent of the sites and in bed-sediment samples from 82 percent of the sites. Concentrations of total DDT, total chlordanes, total PCBs, and dieldrin in whole white suckers and in bed sediment were significantly related to urban/industrial basin characteristics, such as percentage of urban land use and population density. Semi-volatile organic compounds (SVOCs)-total polycyclic aromatic hydrocarbons (PAHs), total phthalates, and phenols- were detected frequently in bed-sediment samples. All three types of SVOCs were detected in samples from at least one site in each land-use category. The highest detection rates and concentrations typically were in samples from sites in the urban and mixed land-use categories, as well as from the large-river sites. Concentrations of total PAHs and total phthalates in bed-sediment samples were found to be statistically related to percentages of urban land use and to population density in the drainage areas represented by the sampling sites. The samples of fish tissue and bed sediment collected throughout the DELR were analyzed for a large suite of trace elements, but results of the analyses for eight elements-arsenic, cadmium, chromium, copper, lead, nickel, mercury, and zinc- that are considered contaminants of concern are described in this report. One or more of the eight trace elements were detected in samples from every fish tissue and bed-sediment sampling site, and all of the trace elements were detected in samples from 97 percent of the bed-sediment sites. The concentrations of organic compounds and trace elements in the DELR samples were compared to applicable guidelines for the protection of wildlife and other biological organisms. Concentrations of total DDT, total chlordanes, total PCBs, and dieldrin in fish-tissue samples from 14 sites exceeded one or more of the Wildlife Protective Guidelines established by the New York State Department of Environmental Conservation. Concentrations of one or more organic compounds in samples from 16 bed-sediment sites exceeded the Threshold Effects Concentrations (TEC) of the Canadian Sediment Quality Guidelines, and concentrations of one or more of the eight trace elements in samples from 38 bed-sediment sites exceeded the TEC. (The TEC is the concentration below which adverse biological effects in freshwater ecosystems are expected to be rare.) Concentrations of organic compounds in samples from some bed-sediment sites exceeded the Canadian Probable Effects Concentrations (PEC), and concentrations of trace elements in samples from 18 sites exceeded the PEC. (The PEC is the concentration above which adverse effects to biological organisms are expected to occur frequently). Concentrations of organic compounds and trace elements in samples from the DELR were compared to similar data from other NAWQA study units in the northeastern United States and also data from the Mobile River (Alabama) Basin and the Northern Rockies Intermontane Basin study units. Median concentrations of to

Mapping moderate-scale land-cover over very large geographic areas within a collaborative framework: A case study of the Southwest Regional Gap Analysis Project (SWReGAP)

USGS Publications Warehouse

Lowry, J.; Ramsey, R.D.; Thomas, K.; Schrupp, D.; Sajwaj, T.; Kirby, J.; Waller, E.; Schrader, S.; Falzarano, S.; Langs, L.; Manis, G.; Wallace, C.; Schulz, K.; Comer, P.; Pohs, K.; Rieth, W.; Velasquez, C.; Wolk, B.; Kepner, W.; Boykin, K.; O'Brien, L.; Bradford, D.; Thompson, B.; Prior-Magee, J.

2007-01-01

Land-cover mapping efforts within the USGS Gap Analysis Program have traditionally been state-centered; each state having the responsibility of implementing a project design for the geographic area within their state boundaries. The Southwest Regional Gap Analysis Project (SWReGAP) was the first formal GAP project designed at a regional, multi-state scale. The project area comprises the southwestern states of Arizona, Colorado, Nevada, New Mexico, and Utah. The land-cover map/dataset was generated using regionally consistent geospatial data (Landsat ETM+ imagery (1999-2001) and DEM derivatives), similar field data collection protocols, a standardized land-cover legend, and a common modeling approach (decision tree classifier). Partitioning of mapping responsibilities amongst the five collaborating states was organized around ecoregion-based "mapping zones". Over the course of 21/2 field seasons approximately 93,000 reference samples were collected directly, or obtained from other contemporary projects, for the land-cover modeling effort. The final map was made public in 2004 and contains 125 land-cover classes. An internal validation of 85 of the classes, representing 91% of the land area was performed. Agreement between withheld samples and the validated dataset was 61% (KHAT = .60, n = 17,030). This paper presents an overview of the methodologies used to create the regional land-cover dataset and highlights issues associated with large-area mapping within a coordinated, multi-institutional management framework. ?? 2006 Elsevier Inc. All rights reserved.

Ecology of Pseudallescheria and Scedosporium species in human-dominated and natural environments and their distribution in clinical samples.

PubMed

Kaltseis, J; Rainer, J; De Hoog, G S

2009-06-01

This study aims to determine the occurrence of Pseudallescheria and Scedosporium species in natural and human-dominated environments. Habitats (136 sampling sites) in a transect with increasing human impact were investigated (natural areas, agricultural soils, urban playgrounds, industrial areas). Physico-chemical parameters were measured to characterize the different areas included in this investigation. Fungal identification was performed by morphology and sequence data analysis. Comparative description of virulence was largely based on the database of the ECMM/ISHAM Working Group on Pseudallescheria/Scedosporium Infections. Pseudallescheria and Scedosporium species were most abundant in industrial areas, followed by urban playgrounds and agricultural areas. None of the species were isolated from natural habitats. The abundance of Pseudallescheria and Scedosporium species could be correlated with increasing nitrogen concentrations (P<0.01) and decreasing pH (P<0.05) within a pH range of 6.1-7.5. In general, frequency of the different Pseudallescheria and Scedosporium species in the environment is strongly enhanced by human activities, and largely differs from species distribution in clinical settings, suggesting that these species have different degrees of virulence. Pseudallescheria boydii is relatively frequently found as agent of human disease, while Scedosporium dehoogii is found almost exclusively in the environment. Scedosporium apiospermum is responsible for the majority of infections and is found at comparable frequency in the environment; S. aurantiacum and P. minutispora showed similar spectra, but at much lower frequencies.

Holes generation in glass using large spot femtosecond laser pulses

NASA Astrophysics Data System (ADS)

Berg, Yuval; Kotler, Zvi; Shacham-Diamand, Yosi

2018-03-01

We demonstrate high-throughput, symmetrical, holes generation in fused silica glass using a large spot size, femtosecond IR-laser irradiation which modifies the glass properties and yields an enhanced chemical etching rate. The process relies on a balanced interplay between the nonlinear Kerr effect and multiphoton absorption in the glass which translates into symmetrical glass modification and increased etching rate. The use of a large laser spot size makes it possible to process thick glasses at high speeds over a large area. We have demonstrated such fabricated holes with an aspect ratio of 1:10 in a 1 mm thick glass samples.

Sulfate and nitrate in Asian dust particles observed in desert, coastal and marine air

NASA Astrophysics Data System (ADS)

Zhang, D.; Wu, F.; Junji, C.

2016-12-01

Sulfate and nitrate in dust particles are believed to be two key species which can largely alter the physical and chemical properties of the particles in the atmosphere, in particular under humid conditions. Their occurrence in the particles has usually been considered to be the consequence of particles' aging during their long-distance travel in the air although they are present in some crustal minerals. Our observations at two deserts in China during dust episodes revealed that there were soil-derived sulfate and background-like nitrate in atmospheric dust samples. Sulfate in dust samples was proportional to samples' mass and comprised at steady mass percentages in differently sized samples. In contrast, nitrate concentration was approximately stable and independent from dust loading. Our observations at inland and coastal areas of China during dust episodes revealed that sulfate and nitrate were hardly produced on the surface of dust particles that were originated from the deserts areas in northwestern China. This is because the dust particles were in the postfrontal air, where the temperature was low and the relative humidity was small due to the adiabatic properties of the air mass. There are a number studies reporting that sulfate and nitrate had been efficiently produced on mineral particles in inland areas of China. However, those mineral particles were more likely from the local areas rather than from the desert areas. Our observations in the coastal areas of Japan, which is located in the downstream areas of the Asian continent and surrounded by sea areas revealed that dust particles appearing there frequently contained sulfate and nitrate, indicating sulfate and nitrate had been efficiently produced on the surface of the particles when the particles traveled in the marine air between China and Japan.

Using Technology to Better Characterize the Apollo Sample Suite: A Retroactive PET Analysis and Potential Model for Future Sample Return Missions

NASA Technical Reports Server (NTRS)

Zeigler, R. A.

2015-01-01

From 1969-1972 the Apollo missions collected 382 kg of lunar samples from six distinct locations on the Moon. Studies of the Apollo sample suite have shaped our understanding of the formation and early evolution of the Earth-Moon system, and have had important implications for studies of the other terrestrial planets (e.g., through the calibration of the crater counting record) and even the outer planets (e.g., the Nice model of the dynamical evolution of the Solar System). Despite nearly 50 years of detailed research on Apollo samples, scientists are still developing new theories about the origin and evolution of the Moon. Three areas of active research are: (1) the abundance of water (and other volatiles) in the lunar mantle, (2) the timing of the formation of the Moon and the duration of lunar magma ocean crystallization, (3) the formation of evolved lunar lithologies (e.g., granites) and implications for tertiary crustal processes on the Moon. In order to fully understand these (and many other) theories about the Moon, scientists need access to "new" lunar samples, particularly new plutonic samples. Over 100 lunar meteorites have been identified over the past 30 years, and the study of these samples has greatly aided in our understanding of the Moon. However, terrestrial alteration and the lack of geologic context limit what can be learned from the lunar meteorites. Although no "new" large plutonic samples (i.e., hand-samples) remain to be discovered in the Apollo sample collection, there are many large polymict breccias in the Apollo collection containing relatively large (approximately 1 cm or larger) previously identified plutonic clasts, as well as a large number of unclassified lithic clasts. In addition, new, previously unidentified plutonic clasts are potentially discoverable within these breccias. The question becomes how to non-destructively locate and identify new lithic clasts of interest while minimizing the contamination and physical degradation of the samples.

Reconnaissance investigation of water quality, bottom sediment, and biota associated with irrigation drainage in the Pine River Project area, Southern Ute Indian Reservation, southwestern Colorado and northwestern New Mexico, 1988-89

USGS Publications Warehouse

Butler, D.L.; Krueger, R.P.; Osmundson, B.C.; Thompson, A.L.; Formea, J.J.; Wickman, D.W.

1993-01-01

During 1988-89, water, bottom sediment, biota, soil, and plants were sampled for a reconnaissance investigation of the Pine River Project area in southwestern Colorado. Irrigation drainage does not seem to be a major source of dissolved solids in streams. Concentrations of manganese, mercury, and selenium exceeded drinking-water regulations in some streams. The maximum selenium concentration in a stream sample was 94 microg/L in Rock Creek. Irrigation drainage and natural groundwater are sources of some trace elements to streams. Water from a well in a nonirrigated area had 4,800 microg/L of selenium. Selenium concentrations in soil on the Oxford Tract were greater in areas previously or presently irrigated than in areas never irrigated. Some forage plants on the Oxford Tract had large selenium concentrations, including 180 mg/km in alfalfa. Most fish samples had selenium concentrations greater than the National Contaminant Biomonitoring Program 85th percentile. Selenium concentrations in aquatic plants, aquatic inverte- brates, and small mammals may be of concern to fish and wildlife because of possible food-chain bioconcentration. Selenium concentrations in bird samples indicate selenium contamination of biota on the Oxford Tract. Mallard breasts had selenium concentrations exceeding a guideline for human consumption. The maximum selenium concentration in biota was 50 microg/g dry weight in a bird liver from the Oxford Tract. In some fish samples, arsenic, cadmium, copper, and zinc exceeded background concentrations, but concentrations were not toxic. Mercury concentrations in 16 fish samples exceeded the background concentration. Ten mercury concentrations in fish exceeded a guideline for mercury in food for consumption by pregnant women.

Parcellating an individual subject's cortical and subcortical brain structures using snowball sampling of resting-state correlations.

PubMed

Wig, Gagan S; Laumann, Timothy O; Cohen, Alexander L; Power, Jonathan D; Nelson, Steven M; Glasser, Matthew F; Miezin, Francis M; Snyder, Abraham Z; Schlaggar, Bradley L; Petersen, Steven E

2014-08-01

We describe methods for parcellating an individual subject's cortical and subcortical brain structures using resting-state functional correlations (RSFCs). Inspired by approaches from social network analysis, we first describe the application of snowball sampling on RSFC data (RSFC-Snowballing) to identify the centers of cortical areas, subdivisions of subcortical nuclei, and the cerebellum. RSFC-Snowballing parcellation is then compared with parcellation derived from identifying locations where RSFC maps exhibit abrupt transitions (RSFC-Boundary Mapping). RSFC-Snowballing and RSFC-Boundary Mapping largely complement one another, but also provide unique parcellation information; together, the methods identify independent entities with distinct functional correlations across many cortical and subcortical locations in the brain. RSFC parcellation is relatively reliable within a subject scanned across multiple days, and while the locations of many area centers and boundaries appear to exhibit considerable overlap across subjects, there is also cross-subject variability-reinforcing the motivation to parcellate brains at the level of individuals. Finally, examination of a large meta-analysis of task-evoked functional magnetic resonance imaging data reveals that area centers defined by task-evoked activity exhibit correspondence with area centers defined by RSFC-Snowballing. This observation provides important evidence for the ability of RSFC to parcellate broad expanses of an individual's brain into functionally meaningful units. © The Author 2013. Published by Oxford University Press.

Recent advances of mesoporous materials in sample preparation.

PubMed

Zhao, Liang; Qin, Hongqiang; Wu, Ren'an; Zou, Hanfa

2012-03-09

Sample preparation has been playing an important role in the analysis of complex samples. Mesoporous materials as the promising adsorbents have gained increasing research interest in sample preparation due to their desirable characteristics of high surface area, large pore volume, tunable mesoporous channels with well defined pore-size distribution, controllable wall composition, as well as modifiable surface properties. The aim of this paper is to review the recent advances of mesoporous materials in sample preparation with emphases on extraction of metal ions, adsorption of organic compounds, size selective enrichment of peptides/proteins, specific capture of post-translational peptides/proteins and enzymatic reactor for protein digestion. Copyright © 2011 Elsevier B.V. All rights reserved.

Large area 3-D optical coherence tomography imaging of lumpectomy specimens for radiation treatment planning

NASA Astrophysics Data System (ADS)

Wang, Cuihuan; Kim, Leonard; Barnard, Nicola; Khan, Atif; Pierce, Mark C.

2016-02-01

Our long term goal is to develop a high-resolution imaging method for comprehensive assessment of tissue removed during lumpectomy procedures. By identifying regions of high-grade disease within the excised specimen, we aim to develop patient-specific post-operative radiation treatment regimens. We have assembled a benchtop spectral-domain optical coherence tomography (SD-OCT) system with 1320 nm center wavelength. Automated beam scanning enables "sub-volumes" spanning 5 mm x 5 mm x 2 mm (500 A-lines x 500 B-scans x 2 mm in depth) to be collected in under 15 seconds. A motorized sample positioning stage enables multiple sub-volumes to be acquired across an entire tissue specimen. Sub-volumes are rendered from individual B-scans in 3D Slicer software and en face (XY) images are extracted at specific depths. These images are then tiled together using MosaicJ software to produce a large area en face view (up to 40 mm x 25 mm). After OCT imaging, specimens were sectioned and stained with HE, allowing comparison between OCT image features and disease markers on histopathology. This manuscript describes the technical aspects of image acquisition and reconstruction, and reports initial qualitative comparison between large area en face OCT images and HE stained tissue sections. Future goals include developing image reconstruction algorithms for mapping an entire sample, and registering OCT image volumes with clinical CT and MRI images for post-operative treatment planning.

Extending large-scale forest inventories to assess urban forests.

PubMed

Corona, Piermaria; Agrimi, Mariagrazia; Baffetta, Federica; Barbati, Anna; Chiriacò, Maria Vincenza; Fattorini, Lorenzo; Pompei, Enrico; Valentini, Riccardo; Mattioli, Walter

2012-03-01

Urban areas are continuously expanding today, extending their influence on an increasingly large proportion of woods and trees located in or nearby urban and urbanizing areas, the so-called urban forests. Although these forests have the potential for significantly improving the quality the urban environment and the well-being of the urban population, data to quantify the extent and characteristics of urban forests are still lacking or fragmentary on a large scale. In this regard, an expansion of the domain of multipurpose forest inventories like National Forest Inventories (NFIs) towards urban forests would be required. To this end, it would be convenient to exploit the same sampling scheme applied in NFIs to assess the basic features of urban forests. This paper considers approximately unbiased estimators of abundance and coverage of urban forests, together with estimators of the corresponding variances, which can be achieved from the first phase of most large-scale forest inventories. A simulation study is carried out in order to check the performance of the considered estimators under various situations involving the spatial distribution of the urban forests over the study area. An application is worked out on the data from the Italian NFI.

Large-Area Atomic Layers of the Charge-Density-Wave Conductor TiSe2.

PubMed

Wang, Hong; Chen, Yu; Duchamp, Martial; Zeng, Qingsheng; Wang, Xuewen; Tsang, Siu Hon; Li, Hongling; Jing, Lin; Yu, Ting; Teo, Edwin Hang Tong; Liu, Zheng

2018-02-01

Layered transition metal (Ti, Ta, Nb, etc.) dichalcogenides are important prototypes for the study of the collective charge density wave (CDW). Reducing the system dimensionality is expected to lead to novel properties, as exemplified by the discovery of enhanced CDW order in ultrathin TiSe 2 . However, the syntheses of monolayer and large-area 2D CDW conductors can currently only be achieved by molecular beam epitaxy under ultrahigh vacuum. This study reports the growth of monolayer crystals and up to 5 × 10 5 µm 2 large films of the typical 2D CDW conductor-TiSe 2 -by ambient-pressure chemical vapor deposition. Atomic resolution scanning transmission electron microscopy indicates the as-grown samples are highly crystalline 1T-phase TiSe 2 . Variable-temperature Raman spectroscopy shows a CDW phase transition temperature of 212.5 K in few layer TiSe 2 , indicative of high crystal quality. This work not only allows the exploration of many-body state of TiSe 2 in 2D limit but also offers the possibility of utilizing large-area TiSe 2 in ultrathin electronic devices. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cross-identification of large surveys for finding interstellar extinction

NASA Astrophysics Data System (ADS)

Karpov, S. V.; Malkov, O. Yu.; Mironov, A. V.

2012-01-01

The publication of large photometric surveys and the tools for the cross-identification of their objects open up a possibility for obtaining multicolor photometry of hundreds of millions of objects. This, in turn, makes it possible not only to classify the objects and determine their parameters, but also to measure the interstellar extinction towards them and produce an extinction map for the Milky Way. The aim of this study is to develop a tool for the cross identification of objects in the most well-known surveys and test it in several sky areas. To this end, we implemented an algorithm of fast positional matching of large astronomical catalogs in small (up to one degree) sized areas with filtering of false identification. As a result, we drew in seven 0.1-degree radius areas samples of objects from the DENIS, 2MASS, SDSS, GALEX, and UKIDSS surveys, and performed the cross-identification of these surveys. We compiled the corresponding subcatalogs in the VO Table format. The tool developed as a result of this work can be used to cross-identify objects in arbitrary sky areas for the further classification and determination of stellar parameters, including the measurement of the amount of interstellar extinction.

Reliability and statistical power analysis of cortical and subcortical FreeSurfer metrics in a large sample of healthy elderly.

PubMed

Liem, Franziskus; Mérillat, Susan; Bezzola, Ladina; Hirsiger, Sarah; Philipp, Michel; Madhyastha, Tara; Jäncke, Lutz

2015-03-01

FreeSurfer is a tool to quantify cortical and subcortical brain anatomy automatically and noninvasively. Previous studies have reported reliability and statistical power analyses in relatively small samples or only selected one aspect of brain anatomy. Here, we investigated reliability and statistical power of cortical thickness, surface area, volume, and the volume of subcortical structures in a large sample (N=189) of healthy elderly subjects (64+ years). Reliability (intraclass correlation coefficient) of cortical and subcortical parameters is generally high (cortical: ICCs>0.87, subcortical: ICCs>0.95). Surface-based smoothing increases reliability of cortical thickness maps, while it decreases reliability of cortical surface area and volume. Nevertheless, statistical power of all measures benefits from smoothing. When aiming to detect a 10% difference between groups, the number of subjects required to test effects with sufficient power over the entire cortex varies between cortical measures (cortical thickness: N=39, surface area: N=21, volume: N=81; 10mm smoothing, power=0.8, α=0.05). For subcortical regions this number is between 16 and 76 subjects, depending on the region. We also demonstrate the advantage of within-subject designs over between-subject designs. Furthermore, we publicly provide a tool that allows researchers to perform a priori power analysis and sensitivity analysis to help evaluate previously published studies and to design future studies with sufficient statistical power. Copyright © 2014 Elsevier Inc. All rights reserved.

Scoresum - A technique for displaying and evaluating multi-element geochemical information, with examples of its use in regional mineral assessment programs

USGS Publications Warehouse

Chaffee, M.A.

1983-01-01

A technique called SCORESUM was developed to display a maximum of multi-element geochemical information on a minimum number of maps for mineral assessment purposes. The technique can be done manually for a small analytical data set or can be done with a computer for a large data set. SCORESUM can be used with highly censored data and can also weight samples so as to minimize the chemical differences of diverse lithologies in different parts of a given study area. The full range of reported analyses for each element of interest in a data set is divided into four categories. Anomaly scores - values of O (background), 1 (weakly anomalous), 2 (moderately anomalous), and 3 (strongly anomalous) - are substituted for all of the analyses falling into each of the four categories. A group of elements based on known or suspected association in altered or mineralized areas is selected for study and the anomaly scores for these elements are summed for each sample site and then plotted on a map. Some of the results of geochemical studies conducted for mineral assessments in two areas are briefly described. The first area, the Mokelumne Wilderness and vicinity, is a relatively small and geologically simple one. The second, the Walker Lake 1?? ?? 2?? quadrangle, is a large area that has extremely complex geology and that contains a number of different mineral deposit environments. These two studies provide examples of how the SCORESUM technique has been used (1) to enhance relatively small but anomalous areas and (2) to delineate and rank areas containing geochemical signatures for specific suites of elements related to certain types of alteration or mineralization. ?? 1983.

A method for nitrate collection for δ15N and δ18O analysis from waters with low nitrate concentrations

USGS Publications Warehouse

Chang, Cecily C.Y.; Langston, J.; Riggs, M.; Campbell, D.H.; Silva, S.R.; Kendall, C.

1999-01-01

 Recently, methods have been developed to analyze NO3- for δ15N and δ18O, improving our ability to identify NO3- sources and transformations. However, none of the existing methods are suited for waters with low NO3- concentrations (0.7-10 µM). We describe an improved method for collecting and recovering NO3- on exchange columns. To overcome the lengthy collection loading times imposed by the large sample volumes (7-70 L), the sample was prefiltered (0.45 µm) with a large surface area filter. Switching to AG2X anion resin and using a coarser mesh size (100-200) than previous methods also enhanced sample flow. Placement of a cation column in front of the anion column minimized clogging of the anion column by dissolved organic carbon (DOC) accumulation. This also served to minimize transfer of unwanted oxygen atoms from DOC to the 18O portion of the NO3- sample, thereby contaminating the sample and shifting δ18O. The cat-AG2X method is suited for on-site sample collection, making it possible to collect and recover NO3- from low ionic strength waters with modest DOC concentrations (80-800 µM), relieves the investigator of transporting large volumes of water back to the laboratory, and offers a means of sampling rain, snow, snowmelt, and stream samples from access-limited sites.

33 CFR Appendix A to Part 279 - Sample Resource Use Objectives

Code of Federal Regulations, 2011 CFR

2011-07-01

... technical advice. Resource use objective: To establish an ecological study area at Wakulla Wash for the protection and study of its unique vegetative associations. (Discussion) The analysis of pertinent factors... educational purposes; there is a large population base within two hours drive of the project; two local...

Trace-element contents of postorogenic granites of the eastern Arabian Shield, Kingdom of Saudi Arabia

USGS Publications Warehouse

Stuckless, J.S.; Vaughn, R.B.; VanTrump, George

1986-01-01

The regional trends for the chemical data and geochemical correlations over the large area sampled, suggest that the postorogenic granites were derived from a single protolith that formed by the mixing of oceanic sediments from the west, continental sediments from the east.

Galaxy Evolution Studies with the SPace IR Telescope for Cosmology and Astrophysics (SPICA): The Power of IR Spectroscopy

NASA Astrophysics Data System (ADS)

Spinoglio, L.; Alonso-Herrero, A.; Armus, L.; Baes, M.; Bernard-Salas, J.; Bianchi, S.; Bocchio, M.; Bolatto, A.; Bradford, C.; Braine, J.; Carrera, F. J.; Ciesla, L.; Clements, D. L.; Dannerbauer, H.; Doi, Y.; Efstathiou, A.; Egami, E.; Fernández-Ontiveros, J. A.; Ferrara, A.; Fischer, J.; Franceschini, A.; Gallerani, S.; Giard, M.; González-Alfonso, E.; Gruppioni, C.; Guillard, P.; Hatziminaoglou, E.; Imanishi, M.; Ishihara, D.; Isobe, N.; Kaneda, H.; Kawada, M.; Kohno, K.; Kwon, J.; Madden, S.; Malkan, M. A.; Marassi, S.; Matsuhara, H.; Matsuura, M.; Miniutti, G.; Nagamine, K.; Nagao, T.; Najarro, F.; Nakagawa, T.; Onaka, T.; Oyabu, S.; Pallottini, A.; Piro, L.; Pozzi, F.; Rodighiero, G.; Roelfsema, P.; Sakon, I.; Santini, P.; Schaerer, D.; Schneider, R.; Scott, D.; Serjeant, S.; Shibai, H.; Smith, J.-D. T.; Sobacchi, E.; Sturm, E.; Suzuki, T.; Vallini, L.; van der Tak, F.; Vignali, C.; Yamada, T.; Wada, T.; Wang, L.

2017-11-01

IR spectroscopy in the range 12-230 μm with the SPace IR telescope for Cosmology and Astrophysics (SPICA) will reveal the physical processes governing the formation and evolution of galaxies and black holes through cosmic time, bridging the gap between the James Webb Space Telescope and the upcoming Extremely Large Telescopes at shorter wavelengths and the Atacama Large Millimeter Array at longer wavelengths. The SPICA, with its 2.5-m telescope actively cooled to below 8 K, will obtain the first spectroscopic determination, in the mid-IR rest-frame, of both the star-formation rate and black hole accretion rate histories of galaxies, reaching lookback times of 12 Gyr, for large statistically significant samples. Densities, temperatures, radiation fields, and gas-phase metallicities will be measured in dust-obscured galaxies and active galactic nuclei, sampling a large range in mass and luminosity, from faint local dwarf galaxies to luminous quasars in the distant Universe. Active galactic nuclei and starburst feedback and feeding mechanisms in distant galaxies will be uncovered through detailed measurements of molecular and atomic line profiles. The SPICA's large-area deep spectrophotometric surveys will provide mid-IR spectra and continuum fluxes for unbiased samples of tens of thousands of galaxies, out to redshifts of z 6.

Coarse and fine aerosol source apportionment in Rio de Janeiro, Brazil

NASA Astrophysics Data System (ADS)

Godoy, Maria Luiza D. P.; Godoy, José Marcus; Roldão, Luiz Alfredo; Soluri, Daniela S.; Donagemma, Raquel A.

The metropolitan area of Rio de Janeiro is one of the twenty biggest urban agglomerations in the world, with 11 million inhabitants in the metropolitan area, and has a high population density, with 1700 hab. km -2. For this aerosol source apportionment study, the atmospheric aerosol sampling was performed at ten sites distributed in different locations of the metropolitan area from September/2003 to December/2005, with sampling during 24 h on a weekly basis. Stacked filter units (SFU) were used to collect fine and coarse aerosol particles with a flow rate of 17 L min -1. In both size fractions trace elements were analyzed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) as well as water-soluble species by Ion-Chromatography (IC). Also gravimetric analysis and reflectance measurements provided aerosol mass and black carbon concentrations. Very good detection limits for up to 42 species were obtained. Mean annual PM 10 mass concentration ranged from 20 to 37 μg m -3, values that are within the Brazilian air quality standards. Receptor models such as principal factor analysis, cluster analysis and absolute principal factor analysis were applied in order to identify and quantify the aerosol sources. For fine and coarse modes, circa of 100% of the measured mass was quantitatively apportioned to relatively few identified aerosol sources. A very similar and consistent source apportionment was obtained for both fine and coarse modes for all 10 sampling sites. Soil dust is an important component, accounting for 22-72% and for 25-48% of the coarse and fine mass respectively. On the other hand, anthropogenic sources as vehicle traffic and oil combustion represent a relatively high contribution (52-75%) of the fine aerosol mass. The joint use of ICP-MS and IC analysis of species in aerosols has proven to be reliable and feasible for the analysis of large amount of samples, and the coupling with receptor models provided an excellent method for quantitative aerosol source apportionment in large urban areas.

Towards an Automatic Framework for Urban Settlement Mapping from Satellite Images: Applications of Geo-referenced Social Media and One Class Classification

NASA Astrophysics Data System (ADS)

Miao, Zelang

2017-04-01

Currently, urban dwellers comprise more than half of the world's population and this percentage is still dramatically increasing. The explosive urban growth over the next two decades poses long-term profound impact on people as well as the environment. Accurate and up-to-date delineation of urban settlements plays a fundamental role in defining planning strategies and in supporting sustainable development of urban settlements. In order to provide adequate data about urban extents and land covers, classifying satellite data has become a common practice, usually with accurate enough results. Indeed, a number of supervised learning methods have proven effective in urban area classification, but they usually depend on a large amount of training samples, whose collection is a time and labor expensive task. This issue becomes particularly serious when classifying large areas at the regional/global level. As an alternative to manual ground truth collection, in this work we use geo-referenced social media data. Cities and densely populated areas are an extremely fertile land for the production of individual geo-referenced data (such as GPS and social network data). Training samples derived from geo-referenced social media have several advantages: they are easy to collect, usually they are freely exploitable; and, finally, data from social media are spatially available in many locations, and with no doubt in most urban areas around the world. Despite these advantages, the selection of training samples from social media meets two challenges: 1) there are many duplicated points; 2) method is required to automatically label them as "urban/non-urban". The objective of this research is to validate automatic sample selection from geo-referenced social media and its applicability in one class classification for urban extent mapping from satellite images. The findings in this study shed new light on social media applications in the field of remote sensing.

[Polycyclic aromatic hidrocarbons deposition in the Milazzo-Valle del Mela (Sicily Region, Southern Italy) high-risk area following an oil refinery fire].

PubMed

Grechi, Daniele; Biggeri, Annibale

2016-01-01

On September 2014, a fire began within an oil refinery involving a storage tank containing several hundreds of thousands cubic meters of virgin naphtha. Mayors of neighbouring municipalities asked the Epidemiology and Prevention Society "Giulio A. Maccacaro" to carry out an environmental survey in order to evaluate what was the nature and how dangerous was suspended dust deposited by the fumes. In the following days, after fire had been extinguished we conducted a sample survey on the presence of polycyclic aromatic hydrocarbons (PAH) and metals in particulate deposited on the soil on a radius of five kilometres from the refinery and we engaged the exposed population. The Milazzo-Valle del Mela (Sicily Region, Southern Italy) high-risk area includes several industrial plants; among them, an oil refinery and a fuel powered energy plant. As reference area we selected the Sarroch municipality (Sardinia Region, Southern Italy), in the coast of the Tyrrhenian Sea, which is geographically comparable, where a large oil refinery is located and where an environmental campaign with measurement of PAH and metals in particulate matter was ongoing. Qualitatively, metal composition of particulate matter resulted similar in the Sarroch and Milazzo samples. Instead, a large excess of PAH was documented in the Milazzo samples as compared to the Sarroch ones. In conclusion, the results of the analysis of the samples of particulate matter deposited in the Milazzo area in the days immediately following the oil refinery fire showed a high quantity of PAH, carcinogenic substances which pose major hazard to population health. The greater fall-out was registered in the proximity of the burnt storage tank and the West neighbourhood, and at lesser extent in the Southern neighbourhood. As a consequence, there was a population exposure to carcinogenic substances which could have reached the food chain.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scheuermann, James R., E-mail: James.Scheuermann@stonybrook.edu; Goldan, Amir H.; Zhao, Wei

Purpose: Active matrix flat panel imagers (AMFPI) have limited performance in low dose applications due to the electronic noise of the thin film transistor (TFT) array. A uniform layer of avalanche amorphous selenium (a-Se) called high gain avalanche rushing photoconductor (HARP) allows for signal amplification prior to readout from the TFT array, largely eliminating the effects of the electronic noise. The authors report preliminary avalanche gain measurements from the first HARP structure developed for direct deposition onto a TFT array. Methods: The HARP structure is fabricated on a glass substrate in the form of p-i-n, i.e., the electron blocking layermore » (p) followed by an intrinsic (i) a-Se layer and finally the hole blocking layer (n). All deposition procedures are scalable to large area detectors. Integrated charge is measured from pulsed optical excitation incident on the top electrode (as would in an indirect AMFPI) under continuous high voltage bias. Avalanche gain measurements were obtained from samples fabricated simultaneously at different locations in the evaporator to evaluate performance uniformity across large area. Results: An avalanche gain of up to 80 was obtained, which showed field dependence consistent with previous measurements from n-i-p HARP structures established for vacuum tubes. Measurements from multiple samples demonstrate the spatial uniformity of performance using large area deposition methods. Finally, the results were highly reproducible during the time course of the entire study. Conclusions: We present promising avalanche gain measurement results from a novel HARP structure that can be deposited onto a TFT array. This is a crucial step toward the practical feasibility of AMFPI with avalanche gain, enabling quantum noise limited performance down to a single x-ray photon per pixel.« less

Homogeneous near surface activity distribution by double energy activation for TLA

NASA Astrophysics Data System (ADS)

Takács, S.; Ditrói, F.; Tárkányi, F.

2007-10-01

Thin layer activation (TLA) is a versatile tool for activating thin surface layers in order to study real-time the surface loss by wear, corrosion or erosion processes of the activated parts, without disassembling or stopping running mechanical structures or equipment. The research problem is the determination of the irradiation parameters to produce point-like or large area optimal activity-depth distribution in the sample. Different activity-depth profiles can be produced depending on the type of the investigated material and the nuclear reaction used. To produce activity that is independent of the depth up to a certain depth is desirable when the material removed from the surface by wear, corrosion or erosion can be collected completely. By applying dual energy irradiation the thickness of this quasi-constant activity layer can be increased or the deviation of the activity distribution from a constant value can be minimized. In the main, parts made of metals and alloys are suitable for direct activation, but by using secondary particle implantation the wear of other materials can also be studied in a surface range a few micrometers thick. In most practical cases activation of a point-like spot (several mm2) is enough to monitor the wear, corrosion or erosion, but for special problems relatively large surfaces areas of complicated spatial geometry need to be activated uniformly. Two ways are available for fulfilling this task, (1) production of large area beam spot or scanning the beam over the surface in question from the accelerator side, or (2) a programmed 3D movement of the sample from the target side. Taking into account the large variability of tasks occurring in practice, the latter method was chosen as the routine solution in our cyclotron laboratory.

Development of solid-state avalanche amorphous selenium for medical imaging.

PubMed

Scheuermann, James R; Goldan, Amir H; Tousignant, Olivier; Léveillé, Sébastien; Zhao, Wei

2015-03-01

Active matrix flat panel imagers (AMFPI) have limited performance in low dose applications due to the electronic noise of the thin film transistor (TFT) array. A uniform layer of avalanche amorphous selenium (a-Se) called high gain avalanche rushing photoconductor (HARP) allows for signal amplification prior to readout from the TFT array, largely eliminating the effects of the electronic noise. The authors report preliminary avalanche gain measurements from the first HARP structure developed for direct deposition onto a TFT array. The HARP structure is fabricated on a glass substrate in the form of p-i-n, i.e., the electron blocking layer (p) followed by an intrinsic (i) a-Se layer and finally the hole blocking layer (n). All deposition procedures are scalable to large area detectors. Integrated charge is measured from pulsed optical excitation incident on the top electrode (as would in an indirect AMFPI) under continuous high voltage bias. Avalanche gain measurements were obtained from samples fabricated simultaneously at different locations in the evaporator to evaluate performance uniformity across large area. An avalanche gain of up to 80 was obtained, which showed field dependence consistent with previous measurements from n-i-p HARP structures established for vacuum tubes. Measurements from multiple samples demonstrate the spatial uniformity of performance using large area deposition methods. Finally, the results were highly reproducible during the time course of the entire study. We present promising avalanche gain measurement results from a novel HARP structure that can be deposited onto a TFT array. This is a crucial step toward the practical feasibility of AMFPI with avalanche gain, enabling quantum noise limited performance down to a single x-ray photon per pixel.

Estimating occupancy dynamics for large-scale monitoring networks: amphibian breeding occupancy across protected areas in the northeast United States

USGS Publications Warehouse

Miller, David A.W.; Grant, Evan H. Campbell

2015-01-01

Regional monitoring strategies frequently employ a nested sampling design where a finite set of study areas from throughout a region are selected within which intensive sub-sampling occurs. This sampling protocol naturally lends itself to a hierarchical analysis to account for dependence among sub-samples. Implementing such an analysis within a classic likelihood framework is computationally prohibitive with species occurrence data when accounting for detection probabilities. Bayesian methods offer an alternative framework to make this analysis feasible. We demonstrate a general approach for estimating occupancy when data come from a nested sampling design. Using data from a regional monitoring program of wood frogs (Lithobates sylvaticus) and spotted salamanders (Ambystoma maculatum) in vernal pools, we analyzed data using static and dynamic occupancy frameworks. We analyzed observations from 2004-2013collected within 14 protected areas located throughout the northeast United States . We use the data set to estimate trends in occupancy at both the regional and individual protected area level. We show that occupancy at the regional level was relatively stable for both species. Much more variation occurred within individual study areas, with some populations declining and some increasing for both species. We found some evidence for a latitudinal gradient in trends among protected areas. However, support for this pattern is overestimated when the hierarchical nature of the data collection is not controlled for in the analysis. For both species, occupancy appeared to be declining in the most southern areas, while occupancy was stable or increasing in more northern areas. These results shed light on the range-level population status of these pond-breeding amphibians and our approach provides a framework that can be used to examine drivers of change including among-year and among-site variation in occurrence dynamics, while properly accounting for nested structure of data collection.

Intra-lake variation in maturity, fecundity, and spawning of slimy sculpins (Cottus cognatus) in southern Lake Ontario

USGS Publications Warehouse

Owens, Randall W.; Noguchi, George E.

1998-01-01

Knowledge of the spawning cycle and factors affecting fecundity of slimy sculpins (Cottus cognatus) are important in understanding the population dynamics of this species in large lake systems, like Lake Ontario. Fecundity and the spawning cycle of slimy sculpins were described from samples of slimy sculpins and their egg masses collected with bottom trawls during four annual surveys, April to October, 1988 to 1994. Incidence of gravid females and collections of their egg masses indicated that spawning by slimy sculpins likely occurred from late April to mid October in Lake Ontario. Protracted spawning by slimy sculpins in Lake Ontario is probably a function of the annual water temperature cycle at various depths. Mean length of gravid females was inversely related to density of slimy sculpins. Fecundity ranged from 55 to 1,157 eggs among fish 55 to 127 mm long, and for similar-sized fish, fecundity was inversely related to density of slimy sculpins. Fecundity was about 50% higher at Olcott, where population indices of slimy sculpins were low, compared with Nine Mile Point where indices were much higher. Somatic weight or total length were both good predictors of fecundity. Lipid content of slimy sculpins was lower in an area of high sculpin abundance than in an area of low sculpin abundance, suggesting that fecundity was a function of density-dependent food availability. In large aquatic ecosystems, samples from more than one area may be necessary to describe fecundity of a sedentary species like slimy sculpin, especially if fish densities vary considerably among geographic areas. Large geographic variations in fecundity may be an indicator of spatial imbalance of a species with its prey. Low fecundity may be a compensatory response to slimy sculpins to low food supplies, thereby limiting population growth.

Clustering on very small scales from a large sample of confirmed quasar pairs: does quasar clustering track from Mpc to kpc scales?

NASA Astrophysics Data System (ADS)

Eftekharzadeh, S.; Myers, A. D.; Hennawi, J. F.; Djorgovski, S. G.; Richards, G. T.; Mahabal, A. A.; Graham, M. J.

2017-06-01

We present the most precise estimate to date of the clustering of quasars on very small scales, based on a sample of 47 binary quasars with magnitudes of g < 20.85 and proper transverse separations of ˜25 h-1 kpc. Our sample of binary quasars, which is about six times larger than any previous spectroscopically confirmed sample on these scales, is targeted using a kernel density estimation (KDE) technique applied to Sloan Digital Sky Survey (SDSS) imaging over most of the SDSS area. Our sample is 'complete' in that all of the KDE target pairs with 17.0 ≲ R ≲ 36.2 h-1 kpc in our area of interest have been spectroscopically confirmed from a combination of previous surveys and our own long-slit observational campaign. We catalogue 230 candidate quasar pairs with angular separations of <8 arcsec, from which our binary quasars were identified. We determine the projected correlation function of quasars (\\bar{W}_p) in four bins of proper transverse scale over the range 17.0 ≲ R ≲ 36.2 h-1 kpc. The implied small-scale quasar clustering amplitude from the projected correlation function, integrated across our entire redshift range, is A = 24.1 ± 3.6 at ˜26.6 h-1 kpc. Our sample is the first spectroscopically confirmed sample of quasar pairs that is sufficiently large to study how quasar clustering evolves with redshift at ˜25 h-1 kpc. We find that empirical descriptions of how quasar clustering evolves with redshift at ˜25 h-1 Mpc also adequately describe the evolution of quasar clustering at ˜25 h-1 kpc.

The observed clustering of damaging extra-tropical cyclones in Europe

NASA Astrophysics Data System (ADS)

Cusack, S.

2015-12-01

The clustering of severe European windstorms on annual timescales has substantial impacts on the re/insurance industry. Management of the risk is impaired by large uncertainties in estimates of clustering from historical storm datasets typically covering the past few decades. The uncertainties are unusually large because clustering depends on the variance of storm counts. Eight storm datasets are gathered for analysis in this study in order to reduce these uncertainties. Six of the datasets contain more than 100~years of severe storm information to reduce sampling errors, and the diversity of information sources and analysis methods between datasets sample observational errors. All storm severity measures used in this study reflect damage, to suit re/insurance applications. It is found that the shortest storm dataset of 42 years in length provides estimates of clustering with very large sampling and observational errors. The dataset does provide some useful information: indications of stronger clustering for more severe storms, particularly for southern countries off the main storm track. However, substantially different results are produced by removal of one stormy season, 1989/1990, which illustrates the large uncertainties from a 42-year dataset. The extended storm records place 1989/1990 into a much longer historical context to produce more robust estimates of clustering. All the extended storm datasets show a greater degree of clustering with increasing storm severity and suggest clustering of severe storms is much more material than weaker storms. Further, they contain signs of stronger clustering in areas off the main storm track, and weaker clustering for smaller-sized areas, though these signals are smaller than uncertainties in actual values. Both the improvement of existing storm records and development of new historical storm datasets would help to improve management of this risk.

Sparsely sampling the sky: a Bayesian experimental design approach

NASA Astrophysics Data System (ADS)

Paykari, P.; Jaffe, A. H.

2013-08-01

The next generation of galaxy surveys will observe millions of galaxies over large volumes of the Universe. These surveys are expensive both in time and cost, raising questions regarding the optimal investment of this time and money. In this work, we investigate criteria for selecting amongst observing strategies for constraining the galaxy power spectrum and a set of cosmological parameters. Depending on the parameters of interest, it may be more efficient to observe a larger, but sparsely sampled, area of sky instead of a smaller contiguous area. In this work, by making use of the principles of Bayesian experimental design, we will investigate the advantages and disadvantages of the sparse sampling of the sky and discuss the circumstances in which a sparse survey is indeed the most efficient strategy. For the Dark Energy Survey (DES), we find that by sparsely observing the same area in a smaller amount of time, we only increase the errors on the parameters by a maximum of 0.45 per cent. Conversely, investing the same amount of time as the original DES to observe a sparser but larger area of sky, we can in fact constrain the parameters with errors reduced by 28 per cent.

Water quality analysis of the Rapur area, Andhra Pradesh, South India using multivariate techniques

NASA Astrophysics Data System (ADS)

Nagaraju, A.; Sreedhar, Y.; Thejaswi, A.; Sayadi, Mohammad Hossein

2017-10-01

The groundwater samples from Rapur area were collected from different sites to evaluate the major ion chemistry. The large number of data can lead to difficulties in the integration, interpretation, and representation of the results. Two multivariate statistical methods, hierarchical cluster analysis (HCA) and factor analysis (FA), were applied to evaluate their usefulness to classify and identify geochemical processes controlling groundwater geochemistry. Four statistically significant clusters were obtained from 30 sampling stations. This has resulted two important clusters viz., cluster 1 (pH, Si, CO3, Mg, SO4, Ca, K, HCO3, alkalinity, Na, Na + K, Cl, and hardness) and cluster 2 (EC and TDS) which are released to the study area from different sources. The application of different multivariate statistical techniques, such as principal component analysis (PCA), assists in the interpretation of complex data matrices for a better understanding of water quality of a study area. From PCA, it is clear that the first factor (factor 1), accounted for 36.2% of the total variance, was high positive loading in EC, Mg, Cl, TDS, and hardness. Based on the PCA scores, four significant cluster groups of sampling locations were detected on the basis of similarity of their water quality.

Patterns of Occurrence of Sharks in Sydney Harbour, a Large Urbanised Estuary.

PubMed

Smoothey, Amy F; Gray, Charles A; Kennelly, Steve J; Masens, Oliver J; Peddemors, Victor M; Robinson, Wayne A

2016-01-01

Information about spatial and temporal variability in the distribution and abundance of shark-populations are required for their conservation, management and to update measures designed to mitigate human-shark interactions. However, because some species of sharks are mobile, migratory and occur in relatively small numbers, estimating their patterns of distribution and abundance can be very difficult. In this study, we used a hierarchical sampling design to examine differences in the composition of species, size- and sex-structures of sharks sampled with bottom-set longlines in three different areas with increasing distance from the entrance of Sydney Harbour, a large urbanised estuary. During two years of sampling, we obtained data for four species of sharks (Port Jackson, Heterodontus portusjacksoni; wobbegong, Orectolobus maculatus; dusky whaler, Carcharhinus obscurus and bull shark, Carcharhinus leucas). Only a few O. maculatus and C. obscurus were caught, all in the area closest to the entrance of the Harbour. O. maculatus were caught in all seasons, except summer, while C. obscurus was only caught in summer. Heterodontus portusjacksoni were the most abundant species, caught in the entrance location mostly between July to November, when water temperature was below 21.5°C. This pattern was consistent across both years. C. leucas, the second most abundant species, were captured in all areas of Sydney Harbour but only in summer and autumn when water temperatures were above 23°C. This study quantified, for this first time, how different species utilise different areas of Sydney Harbour, at different times of the year. This information has implications for the management of human-shark interactions, by enabling creation of education programs to modify human behaviour in times of increased risk of potentially dangerous sharks.

Patterns of Occurrence of Sharks in Sydney Harbour, a Large Urbanised Estuary

PubMed Central

Smoothey, Amy F.; Gray, Charles A.; Kennelly, Steve J.; Masens, Oliver J.; Peddemors, Victor M.; Robinson, Wayne A.

2016-01-01

Information about spatial and temporal variability in the distribution and abundance of shark-populations are required for their conservation, management and to update measures designed to mitigate human-shark interactions. However, because some species of sharks are mobile, migratory and occur in relatively small numbers, estimating their patterns of distribution and abundance can be very difficult. In this study, we used a hierarchical sampling design to examine differences in the composition of species, size- and sex-structures of sharks sampled with bottom-set longlines in three different areas with increasing distance from the entrance of Sydney Harbour, a large urbanised estuary. During two years of sampling, we obtained data for four species of sharks (Port Jackson, Heterodontus portusjacksoni; wobbegong, Orectolobus maculatus; dusky whaler, Carcharhinus obscurus and bull shark, Carcharhinus leucas). Only a few O. maculatus and C. obscurus were caught, all in the area closest to the entrance of the Harbour. O. maculatus were caught in all seasons, except summer, while C. obscurus was only caught in summer. Heterodontus portusjacksoni were the most abundant species, caught in the entrance location mostly between July to November, when water temperature was below 21.5°C. This pattern was consistent across both years. C. leucas, the second most abundant species, were captured in all areas of Sydney Harbour but only in summer and autumn when water temperatures were above 23°C. This study quantified, for this first time, how different species utilise different areas of Sydney Harbour, at different times of the year. This information has implications for the management of human-shark interactions, by enabling creation of education programs to modify human behaviour in times of increased risk of potentially dangerous sharks. PMID:26824349

Hydrogen stable isotopic constraints on methane emissions from oil and gas extraction in the Colorado Front Range, USA

NASA Astrophysics Data System (ADS)

Townsend-Small, A.; Botner, E. C.; Jimenez, K.; Blake, N. J.; Schroeder, J.; Meinardi, S.; Barletta, B.; Simpson, I. J.; Blake, D. R.; Flocke, F. M.; Pfister, G.; Bon, D.; Crawford, J. H.

2015-12-01

The climatic implications of a shift from oil and coal to natural gas depend on the magnitude of fugitive emissions of methane from the natural gas supply chain. Attempts to constrain methane emissions from natural gas production regions can be confounded by other sources of methane. Here we demonstrate the utility of stable isotopes, particularly hydrogen isotopes, for source apportionment of methane emissions. The Denver, Colorado area is home to a large oil and gas field with both conventional oil and gas wells and newer hydraulic fracturing wells. The region also has a large metropolitan area with several landfills and a sizable cattle population. As part of the DISCOVER-AQ and FRAPPE field campaigns in summer 2014, we collected three types of canister samples for analysis of stable isotopic composition of methane: 1), samples from methane sources; 2), samples from two stationary ground sites, one in the Denver foothills, and one in an oil and gas field; and 3), from the NCAR C-130 aircraft in samples upwind and downwind of the region. Our results indicate that hydrogen isotope ratios are excellent tracers of sources of methane in the region, as we have shown previously in California and Texas. Use of carbon isotope ratios is complicated by the similarity of natural gas isotope ratios to that of background methane. Our results indicate that, despite the large amount of natural gas production in the region, biological sources such as cattle feedlots and landfills account for at least 50% of total methane emissions in the Front Range. Future work includes comparison of isotopes and alkane ratios as tracers of methane sources, and calculation of total methane fluxes in the region using continuous measurements of methane concentrations during aircraft flights.

The large area KX quasar catalogue - I. Analysis of the photometric redshift selection and the complete quasar catalogue

NASA Astrophysics Data System (ADS)

Maddox, Natasha; Hewett, Paul C.; Péroux, Céline; Nestor, Daniel B.; Wisotzki, Lutz

2012-08-01

The results of a large area, ˜600 deg2, K-band flux-limited spectroscopic survey for luminous quasars are presented. The survey utilizes the UKIRT Infrared Deep Sky Survey (UKIDSS) Large Area Survey (LAS) in regions of sky within the Sloan Digital Sky Survey (SDSS) footprint. The K-band excess (KX) of all quasars with respect to Galactic stars is exploited in combination with a photometric redshift/classification scheme to identify quasar candidates for spectroscopic follow-up observations. The data contained within this investigation will be able to provide new constraints on the fraction of luminous quasars reddened by dust with E(B - V) ≤ 0.5 mag. The spectroscopic sample is defined using the K-band, 14.0 ≤ K ≤ 16.6, and SDSS i-band limits of i = 19.5, 19.7 and 22.0 over sky areas of 287, 150 and 196 deg2, respectively. The survey includes >3200 known quasars from the SDSS and more than 250 additional confirmed quasars from the KX selection. A well-defined subsample of quasars in the redshift interval 1.0 ≤ z ≤ 3.5 includes 1152 objects from the SDSS and 172 additional KX-selected quasars. The quasar selection is >95 per cent complete with respect to known SDSS quasars and >95 per cent efficient, largely independent of redshift and i-band magnitude. The properties of the new KX-selected quasars confirm the known redshift-dependent effectiveness of the SDSS quasar selection and provide a sample of luminous quasars experiencing intermediate levels of extinction by dust. The catalogue represents an important step towards the assembly of a well-defined sample of luminous quasars that may be used to investigate the properties of quasars experiencing intermediate levels of dust extinction within their host galaxies or due intervening absorption line systems. †Based on observations made with ESO telescopes at the La Silla Paranal Observatory under programme IDs 083.A0360 and 085.A0359.‡Based on observations collected at the Centro Astronómico Hispano Alemán (CAHA) at Calar Alto, operated jointly by the Max-Planck Institut für Astronomie and the Instituto de Astrofísica de Andalucía (CSIC).

Intrinsic bioremediation potential of a chronically polluted marine coastal area.

PubMed

Catania, Valentina; Santisi, Santina; Signa, Geraldina; Vizzini, Salvatrice; Mazzola, Antonio; Cappello, Simone; Yakimov, Michail M; Quatrini, Paola

2015-10-15

A microbiological survey of the Priolo Bay (eastern coast of Sicily, Ionian Sea), a chronically polluted marine coastal area, was carried out in order to discern its intrinsic bioremediation potential. Microbiological analysis, 16S rDNA-based DGGE fingerprinting and PLFAs analysis were performed on seawater and sediment samples from six stations on two transects. Higher diversity and variability among stations was detected by DGGE in sediment than in water samples although seawater revealed higher diversity of culturable hydrocarbon-degrading bacteria. The most polluted sediment hosted higher total bacterial diversity and higher abundance and diversity of culturable HC degraders. Alkane- and PAH-degrading bacteria were isolated from all stations and assigned to Alcanivorax, Marinobacter, Thalassospira, Alteromonas and Oleibacter (first isolation from the Mediterranean area). High total microbial diversity associated to a large selection of HC degraders is believed to contribute to natural attenuation of the area, provided that new contaminant contributions are avoided. Copyright © 2015 Elsevier Ltd. All rights reserved.

Forest soil chemistry and terrain attributes in a Catskills watershed

USGS Publications Warehouse

Johnson, C.E.; Ruiz-Mendez, J. J.; Lawrence, G.B.

2000-01-01

Knowledge of soil chemistry is useful in assessing the sensitivity of forested areas to natural and anthropogenic disturbances, but characterizing large areas is expensive because of the large sample numbers required and the cost of soil chemical analyses. We collected and chemically analyzed soil samples from 72 sites within a 214-ha watershed in the Catskill Mountains of New York to evaluate factors that influence soil chemistry and whether terrain features could be used to predict soil chemical properties. Using geographic information system (GIS) techniques, we determined five terrain attributes at each sampling location: (i) slope, (ii) aspect, (iii) elevation, (iv) topographic index, and (v) flow accumulation. These attributes were ineffective in predicting the chemical properties of organic and mineral soil samples; together they explained only 4 to 25% of the variance in pH(w), effective cation-exchange capacity (CEC(e)), exchangeable bases, exchangeable acidity, total C, total N, and C/N ratio. Regressions among soil properties were much better; total C and pH(w) together explained 33 to 66% of the variation in exchangeable bases and CEC(e). Total C was positively correlated with N (r = 0.91 and 0.96 in Oa horizons and mineral soil, respectively), exchangeable bases (r = 0.65, 0.76), and CEC(e) (r = 0.54, 0.44), indicating the importance of organic matter to the chemistry of these acidic soils. The fraction of CEC(e) occupied by H explained 44% of the variation in pH(w). Soil chemical properties at this site vary on spatial scales finer than typical GIS analyses, resulting in relationships with poor predictive power. Thus, interrelationships among soil properties are more reliable for prediction.Knowledge of soil chemistry is useful in assessing the sensitivity of forested areas to natural and anthropogenic disturbances, but characterizing large areas is expensive because of the large sample numbers required and the cost of soil chemical analyses. We collected and chemically analyzed soil samples from 72 sites within a 214-ha watershed in the Catskill Mountains of New York to evaluate factors that influence soil chemistry and whether terrain features could be used to predict soil chemical properties. Using geographic information system (GIS) techniques, we determined five terrain attributes at each sampling location: (i) slope, (ii) aspect, (iii) elevation, (iv) topographic index, and (v) flow accumulation. These attributes were ineffective in predicting the chemical properties of organic and mineral soil samples; together they explained only 4 to 25% of the variance in pHw, effective cation-exchange capacity (CECe), exchangeable bases, exchangeable acidity, total C, total N, and C/N ratio. Regressions among soil properties were much better; total C and pHw together explained 33 to 66% of the variation in exchangeable bases and CECe. Total C was positively correlated with N (r = 0.91 and 0.96 in Oa horizons and mineral soil, respectively), exchangeable bases (r = 0.65, 0.76), and CECe (r = 0.54, 0.44), indicating the importance of organic matter to the chemistry of these acidic soils. The fraction of CECe occupied by H explained 44% of the variation in pHw. Soil chemical properties at this site vary on spatial scales finer than typical GIS analyses, resulting in relationships with poor predictive power. Thus, interrelationships among soil properties are more reliable for prediction.

Large-Scale Biaxial Friction Experiments with an Assistance of the NIED Shaking Table

NASA Astrophysics Data System (ADS)

Fukuyama, E.; Mizoguchi, K.; Yamashita, F.; Togo, T.; Kawakata, H.; Yoshimitsu, N.; Shimamoto, T.; Mikoshiba, T.; Sato, M.; Minowa, C.

2012-12-01

We constructed a large-scale biaxial friction apparatus using a large shaking table working at NIED (table dimension is 15m x 15m). The actuator of the shaking table becomes the engine of the constant speed loading. We used a 1.5m long rock sample overlaid on a 2m one. Their height and width are both 0.5m. Therefore, the slip area is 1.5m x 0.5m. The 2m long sample moves with the shaking table and the 1.5m sample is fixed to the basement of the shaking table. Thus, the shaking table displacement controls the dislocation between two rock samples. The shaking table can generate 0.4m displacement with a velocity ranging between 0.0125mm/s and 1m/s. We used Indian gabbro for the rock sample of the present experiments. Original flatness of the sliding surface was formed less than 0.024mm undulation using a large-scale plane grinder. Surface roughness evolved as subsequent experiments were done. Wear material was generated during each experiment, whose grain size becomes bigger as the experiments proceed. This might suggest a damage evolution on the sliding surface. In some experiments we did not remove the gouge material before sliding to examine the effect of gouge layer. Normal stress can be applied up to 1.3MPa. The stiffness of this apparatus was measured experimentally and was of the order of 0.1GN/m. We first measured the coefficient of friction at low sliding velocity (0.1~1mm/s) where the steady state was achieved after the slip of ~5mm. The coefficient of friction was about 0.75 under the normal stress between 0.13 and 1.3MPa. This is consistent with those estimated by previous works using smaller rock samples. We observed that the coefficient of friction decreased gradually with increasing slip velocity, but simultaneously the friction curves at the higher velocities are characterized by stick-slip vibration. Our main aim of the experiments is to understand the rupture propagation from slow nucleation to fast unstable rupture during the loading of two contact surfaces. We recorded many unstable slip events that nucleated inside the sliding surface but did not reach the edge of the sliding surface until the termination of slip. These slip events simulate full rupture process during earthquake, including nucleation, propagation and termination of the rupture. We monitored these rupture progress using the strain change propagation measured by 16 semiconductor strain gauges recorded at a sampling rate of 1MHz. In addition, high frequency waves emitted from AE events was continuously observed by 8 piezo-electronic transducers (PZTs) at a sampling rate of 20MHz. These sensors were attached at the edge of the slipping area. The AE event started to occur where the slip was nucleated and the slip area started to expand. Unfortunately, we could not locate all AE events during the unstable rupture, because of the overprints of signals from multiple events in the PZT records. We also monitored the amplitudes of transmitted waves across the sliding surface. The amplitudes decreased just after the stick slip and recovered gradually, suggesting that the transmitted wave amplitudes might reflect the slipped area on the interface.

Valley fill in the Roswell-Artesia area, New Mexico

USGS Publications Warehouse

Lyford, Forest P.

1973-01-01

Drill samples from 225 water and oil wells in an area 70 miles long and 20 miles wide in the Roswell-Artesia area, southeastern New Mexico were examined. A thickness map and a saturated thickness map of the valley-fill sediments were constructed. Maximum depth of valley fill is about 300 feet in large closed depressions near Roswell, Hagerman, and Artesia. The depressions were formed by the solution of carbonates and evaporites that underlie the fill. Maximum saturated thickness is about 250 feet in depressions near Hagerman and Artesia and about 300 feet in a depression near Roswell.

Regional aeolian dynamics and sand mixing in the Gran Desierto - Evidence from Landsat Thematic Mapper images

NASA Technical Reports Server (NTRS)

Blount, Grady; Greeley, Ronald; Christensen, Phillip R.; Smith, Milton O.; Adams, John B.

1990-01-01

Mesoscale mapping of spatial variations in sand composition of the Gran Desierto (Sonora, Mexico) was carried out on multispectral Landsat TM images of this region, making it possible to examine the dynamic development of sand sheets and dunes. Compositions determined from remote imagery were found to agree well with samples from selected areas. The sand populations delineated were used to describe the sediment source areas, transport paths, and deposition sites. The image analysis revealed important compositional variations aver large areas that were not readily apparent in the field data.

Long-term airborne contamination studied by attic dust in an industrial area: Ajka, Hungary

NASA Astrophysics Data System (ADS)

Völgyesi, P.; Jordan, G.; Szabo, Cs.

2012-04-01

Heavy industrial activities such as mining, metal industry, coal fired power plants have produced large amount of by-products and wide-spread pollution, particularly in the period of centrally dictated economy after WWII, in Hungary. Several studies suggest that significant amount of these pollutants have been deposited in the urban environment. Nowadays, more than half of the world's population is living in urban areas and people spend almost 80% of their lives indoors in developed countries increasing human health risk due to contamination present in urban dwellings. Attic dust sampling was applied to determine the long-term airborne contamination load in the industrial town of Ajka (Hungary). There has been a high industrial activity in Ajka since the end of the 19th century. In addition to aluminum and alumina industry, coal mining, coal fired power plant and glass industry sites, generated numerous waste heaps which act as multi-contamination sources in the area. In October 2010 the Ajka red mud tailings pond failed and caused an accidental regional contamination of international significance. The major objective of this research was to study and map the spatial distribution of heavy metal contamination in airborne attic dust samples. At 27 sampling sites 30 attic dust samples were collected. Sampling strategy followed a grid-based stratified random sampling design. In each cell a house for attic dust sample collection was selected that was located the closest to a randomly generated point in the grid cell. The project area covers a 8x8 grid of 1x1 km cells with a total area of 64 km2. In order to represent long-term industrial pollution, houses with attics kept intact for at least 30-40 years were selected for sampling. Sampling included the collection of background samples remotely placed from the industrialized urban area. The concentration of the major and toxic elements (Al, Ca, Fe, K, Mg, Mn, Na, P, S, and As, Ba, Cd, Co, Cr, Cu, Li, Mo, Ni, Pb, Se, Sn, Sr, Ti, V, Zn) were measured with ICP-OES and the mercury content was measured with atom absorption spectrometry. Our results show a good spatial correlation of contamination sources and attic dust sampling locations reveal spatial trends as well. Attic dust seems to be an efficient and cheep sampling medium to study long-term airborne contamination and possibly associated human health risk in an industrial area.

Geologic Map of the Meskhent Tessera Quadrangle (V-3), Venus: Evidence for Early Formation and Preservation of Regional Topography

NASA Technical Reports Server (NTRS)

Ivanov, M. A.; Head, James W.

2008-01-01

The area of the Meskhent Tessera quadrangle (V-3, 50-75degN, 60-120degE, Fig. 1) corresponds to a transition zone from the uplands of Ishtar Terra to the west to the lowlands of Atalanta Planitia to the east. The topographic configuration, gravity signature, and presence of large tesserae in Ishtar Terra are consistent with extensive areas of thickened crust and tectonically stabilized lithosphere representing ancient and now extinct regimes of mantle convection. The gravity and topographic characteristics of Atalanta Planitia have been cited as evidence for large-scale mantle downwelling. Thus, the region of Meskhent Tessera quadrangle represents an important sample for the study of the regional history of long-wavelength topography (highlands, midlands, and lowlands), interaction between the downwelling and areas of thickened crust/lithosphere, formation of associated tectonic features, and emplacement of volcanic plains.

A multitracer approach for characterizing interactions between shallow groundwater and the hydrothermal system in the Norris Geyser Basin area, Yellowstone National Park

USGS Publications Warehouse

Gardner, W.P.; Susong, D.D.; Solomon, D.K.; Heasler, H.P.

2011-01-01

Multiple environmental tracers are used to investigate age distribution, evolution, and mixing in local- to regional-scale groundwater circulation around the Norris Geyser Basin area in Yellowstone National Park. Springs ranging in temperature from 3??C to 90??C in the Norris Geyser Basin area were sampled for stable isotopes of hydrogen and oxygen, major and minor element chemistry, dissolved chlorofluorocarbons, and tritium. Groundwater near Norris Geyser Basin is comprised of two distinct systems: a shallow, cool water system and a deep, high-temperature hydrothermal system. These two end-member systems mix to create springs with intermediate temperature and composition. Using multiple tracers from a large number of springs, it is possible constrain the distribution of possible flow paths and refine conceptual models of groundwater circulation in and around a large, complex hydrothermal system. Copyright 2011 by the American Geophysical Union.

Thermoacoustic and photoacoustic characterizations of few-layer graphene by pulsed excitations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xiong; Department of Medical Imaging, The University of Arizona, Tucson, Arizona 85724; School of Information Science and Technology, ShanghaiTech University, Shanghai 200031

2016-04-04

We characterized the thermoacoustic and photoacoustic properties of large-area, few-layer graphene by pulsed microwave and optical excitations. Due to its high electric conductivity and low heat capacity per unit area, graphene lends itself to excellent microwave and optical energy absorption and acoustic signal emanation due to the thermoacoustic effect. When exposed to pulsed microwave or optical radiation, distinct thermoacoustic and photoacoustic signals generated by the few-layer graphene are obtained due to microwave and laser absorption of the graphene, respectively. Clear thermoacoustic and photoacoustic images of large-area graphene sample are achieved. A numerical model is developed and the simulated results aremore » in good accordance with the measured ones. This characterization work may find applications in ultrasound generator and detectors for microwave and optical radiation. It may also become an alternative characterization approach for graphene and other types of two-dimensional materials.« less

[Diversity, relative abundance and activity patterns of medium and large mammals in a tropical deciduous forest in the Isthmus of Tehuantepec, Oaxaca, Mexico].

PubMed

Cortés-Marcial, Malinalli; Briones-Salas, Miguel

2014-12-01

The use of camera traps and mammal track search are complementary methods to monitoring species of which is not well documented their natural history, as in the case of medium and large mammals. To ensure its conservation and good management, it is necessary to generate information about the structure of the community and their populations. The objective of the present study was to estimate the diversity, relative abundance and activity patterns of medium and large mammals in a tropical deciduous forest located in the Isthmus of Tehuantepec, Oaxaca, Mexico. Samplings were conducted in three month intervals, from September 2011 to May 2013. We used photographic-sampling and track search, two complementary sampling methods. For photographic-sampling, 12 camera traps were placed covering an area of 60 km2, while for the tracks search a monthly tour of four line-transect surveys of three kilometers length each was undertaken. We obtained a total of 344 pictures with 5292 trap-days total sampling effort; in addition, 187 track records in a total of 144 km. With both methods we registered 21 species of mammals, in 13 families and seven orders, and five species resulted in new records to the area. The diversity index of Shannon-Wiener obtained with the method of tracks was H' = 2.41, while the most abundant species were Urocyon cinereoargen- teus (IAR = 0.23) and Pecari tajacu (IAR = 0.20). By the method of trap the most abundant species were P. tajacu (IAR = 2.62) and Nasua narica (IAR = 1.28). In terms of patterns of activity P. tajacu, N. narica and Odocoileus virginianus were primarily diurnal species; Canis latrans and Leopardus pardalis did not show preference for any schedule in particular, and Didelphis virginiana and Dasypus novemcinctus preferred to have nocturnal activity. This information can be of help to the creation of programs of management and conservation of mam- mals of medium and large in the Isthmus of Tehuantepec, Oaxaca, México.

Hydrology and relation of selected water-quality constituents to selected physical factors in Dakota County, Minnesota, 1990-91

USGS Publications Warehouse

Almendinger, J.E.; Mitton, G.B.

1995-01-01

Selected water-quality constituents were determined in water from 5 surface-water sites and 29 wells in Dakota County, Minnesota, to search for possible relations to selected physical factors, including waste-water discharge, agricultural land, Quaternary deposits, bedrock, soil-leaching potential, and water-table depth. All surface-water samples were from the Vermillion River Basin, whose hydrologic setting was studied to determine its relation to the ground-water flow in the surrounding surficial sand aquifer. Each site was sampled from 1 to 12 times during 1990- 91. A total of 198 samples were collected; selected samples were analyzed for major inorganic ions, nutrients, and triazine content. Physical factors within the area of land assumed to be contributing water to each sampling site were determined from existing mapped or digitized sources. Nitrate concentrations in ground water were related to agricultural land and soil-leaching potential. Nitrate concentrations were large (median 13.2 milligrams per liter as nitrogen) where the percentage of agricultural land in the contributing area was large (equal to or greater than 75 percent) and where the soils had a large soil-leaching potential. Nitrate concentrations were small (median 3.2 milligrams per liter as nitrogen) where the soils had a small soil-leaching potential, despite a large percentage of agricultural land. The statistical relation was not particularly strong, however: the null hypothesis that sites with different soil-leaching potentials had the same nitrate concentrations in ground water was rejected by the Kruskal-Wallis test at only the probability P = 0.15 level. Water-table depth was not an important factor in the relation between nitrate concentrations in ground water and agricultural land. Discharge from a waste-water treatment plant provided most of the downstream loading of nitrate into the Vermillion River mainstem. Triazines were found in small concentrations (less than 2 micrograms per liter) in the Vermillion River and its tributaries. No relation was apparent between selected water-quality constituents and either Quaternary deposits or bedrock.

Helium mining on the Moon: Site selection and evaluation

NASA Technical Reports Server (NTRS)

Cameron, Eugene N.

1992-01-01

The feasibility of recovering helium (He) from the Moon as a source of fusion energy on Earth is currently being studied at the University of Wisconsin. Part of this study is selection and evaluation of potential sites for lunar He mining. Selection and evaluation of potential mining sites are based on four salient findings by various investigators of lunar samples: (1) Regoliths from areas underlain by highland materials contain less than 20 wppm He; (2) Certain maria regoliths contain less than 20 wppm He, but other contain 25 to 49 wppm; (3) The He content of a mare regolith is a function of its composition; regoliths rich in Ti are relatively rich in He; and (4) He is concentrated in the less than 100-micron size fractions of regoliths. The first three findings suggest that maria are the most promising mining sites, specifically, those that have high-Ti regoliths. Information on the regional distribution and extent of high-Ti regoliths comes mainly from two sources: direct sampling by various Apollo and Luna missions, and remote sensing by gamma-ray spectroscopy and Earth-based measurements of lunar spectral reflectance. Sampling provides essential control on calibration and interpretation of data from remote sensing. These data indicate that Mare Tranquillitatis is the principal area of high-Ti regolith of the eastern nearside, but large areas of high-Ti regolith are indicated in the Imbrium and Procellarum regions. Recovery of significant amounts of He-3 will require mining billions of tonnes of regolith. Large individual areas suitable for mining must therefore be delineated. The concentration of He in the finer size fractions and considerations of ease of mining mean that mining areas must be as free as possible of sizable craters and blocks of rock. Pending additional lunar missions, information regarding these features must be obtained from lunar photographs, photogeologic maps, and radar surveys. The present study is decidedly preliminary; available information is much to limited to permit even a close approach to final evaluations. As a prelude to recovery of He from the Moon, systematic exploration and sampling of high-Ti regoliths should therefore have a high priority in future lunar missions.

Quantitative nanoscopy: Tackling sampling limitations in (S)TEM imaging of polymers and composites.

PubMed

Gnanasekaran, Karthikeyan; Snel, Roderick; de With, Gijsbertus; Friedrich, Heiner

2016-01-01

Sampling limitations in electron microscopy questions whether the analysis of a bulk material is representative, especially while analyzing hierarchical morphologies that extend over multiple length scales. We tackled this problem by automatically acquiring a large series of partially overlapping (S)TEM images with sufficient resolution, subsequently stitched together to generate a large-area map using an in-house developed acquisition toolbox (TU/e Acquisition ToolBox) and stitching module (TU/e Stitcher). In addition, we show that quantitative image analysis of the large scale maps provides representative information that can be related to the synthesis and process conditions of hierarchical materials, which moves electron microscopy analysis towards becoming a bulk characterization tool. We demonstrate the power of such an analysis by examining two different multi-phase materials that are structured over multiple length scales. Copyright © 2015 Elsevier B.V. All rights reserved.

OGLE Collection of Star Clusters. New Objects in the Outskirts of the Large Magellanic Cloud

NASA Astrophysics Data System (ADS)

Sitek, M.; Szymański, M. K.; Skowron, D. M.; Udalski, A.; Kostrzewa-Rutkowska, Z.; Skowron, J.; Karczmarek, P.; Cieślar, M.; Wyrzykowski, Ł.; Kozłowski, S.; Pietrukowicz, P.; Soszyński, I.; Mróz, P.; Pawlak, M.; Poleski, R.; Ulaczyk, K.

2016-09-01

The Magellanic System (MS), consisting of the Large Magellanic Cloud (LMC), the Small Magellanic Cloud (SMC) and the Magellanic Bridge (MBR), contains diverse sample of star clusters. Their spatial distribution, ages and chemical abundances may provide important information about the history of formation of the whole System. We use deep photometric maps derived from the images collected during the fourth phase of the Optical Gravitational Lensing Experiment (OGLE-IV) to construct the most complete catalog of star clusters in the Large Magellanic Cloud using the homogeneous photometric data. In this paper we present the collection of star clusters found in the area of about 225 square degrees in the outer regions of the LMC. Our sample contains 679 visually identified star cluster candidates, 226 of which were not listed in any of the previously published catalogs. The new clusters are mainly young small open clusters or clusters similar to associations.

Evaluation of Bayesian Sequential Proportion Estimation Using Analyst Labels

NASA Technical Reports Server (NTRS)

Lennington, R. K.; Abotteen, K. M. (Principal Investigator)

1980-01-01

The author has identified the following significant results. A total of ten Large Area Crop Inventory Experiment Phase 3 blind sites and analyst-interpreter labels were used in a study to compare proportional estimates obtained by the Bayes sequential procedure with estimates obtained from simple random sampling and from Procedure 1. The analyst error rate using the Bayes technique was shown to be no greater than that for the simple random sampling. Also, the segment proportion estimates produced using this technique had smaller bias and mean squared errors than the estimates produced using either simple random sampling or Procedure 1.

Large Area Crop Inventory Experiment (LACIE). Detecting and monitoring agricultural vegetative water stress over large areas using LANDSAT digital data. [Great Plains

NASA Technical Reports Server (NTRS)

Thompson, D. R.; Wehmanen, O. A. (Principal Investigator)

1978-01-01

The author has identified the following significant results. The Green Number Index technique which uses LANDSAT digital data from 5X6 nautical mile sampling frames was expanded to evaluate its usefulness in detecting and monitoring vegetative water stress over the Great Plains. At known growth stages for wheat, segments were classified as drought or non drought. Good agreement was found between the 18 day remotely sensed data and a weekly ground-based crop moisture index. Operational monitoring of the 1977 U.S.S.R. and Australian wheat crops indicated drought conditions. Drought isoline maps produced by the Green Number Index technique were in good agreement with conventional sources.

Preliminary assessment of sources of nitrogen in groundwater at a biosolids-application area near Deer Trail

USGS Publications Warehouse

Yager, Tracy J.B.; McMahon, Peter B.

2012-01-01

Concentrations of dissolved nitrite plus nitrate increased fairly steadily in samples from four shallow groundwater monitoring wells after biosolids applications to nonirrigated farmland began in 1993. The U.S. Geological Survey began a preliminary assessment of sources of nitrogen in shallow groundwater at part of the biosolids-application area near Deer Trail, Colorado, in 2005 in cooperation with the Metro Wastewater Reclamation District. Possible nitrogen sources in the area include biosolids, animal manure, inorganic fertilizer, atmospheric deposition, and geologic materials (bedrock and soil). Biosolids from the Metro Wastewater Reclamation District plant in Denver and biosolids, cow manure, geologic materials (bedrock and soil), and groundwater from the study area were sampled to measure nitrogen content and nitrogen isotopic compositions of nitrate or total nitrogen. Biosolids also were leached, and the leachates were analyzed for nitrogen content and other concentrations. Geologic materials from the study area also were sampled to determine mineralogy. Estimates of nitrogen contributed from inorganic fertilizer and atmospheric deposition were calculated from other published reports. The nitrogen information from the study indicates that each of the sources contain sufficient nitrogen to potentially affect groundwater nitrate concentrations. Natural processes can transform the nitrogen in any of the sources to nitrate in the groundwater. Load calculations indicate that animal manure, inorganic fertilizer, or atmospheric deposition could have contributed the largest nitrogen load to the study area in the 13 years before biosolids applications began, but biosolids likely contributed the largest nitrogen load to the study area in the 13 years after biosolids applications began. Various approaches provided insights into sources of nitrate in the groundwater samples from 2005. The isotopic data indicate that, of the source materials considered, biosolids and (or) animal manure were the most likely sources of nitrate in the wells at the time of sampling (2005), and that inorganic fertilizer, atmospheric deposition, and geologic materials were not substantial sources of nitrate in the wells in 2005. The large total nitrogen content of the biosolids and animal-manure samples and biosolids leachates also indicates that the biosolids and animal manure had potential to leach nitrogen and produce large dissolved nitrate concentrations in groundwater. The available data, however, could not be used to distinguish between biosolids or manure as the dominant source of nitrate in the groundwater because the nitrogen isotopic composition of the two materials is similar. Major-ion data also could not be used to distinguish between biosolids or manure as the dominant source of nitrate in the groundwater because the major-ion composition (as well as the isotopic composition) of the two materials is similar. Without additional data, chloride/bromide mass ratios do not necessarily support or refute the hypothesis that biosolids and (or) animal manure were the primary sources of nitrate in water from the study-area wells in 2005. Concentrations of water-extractable nitrate in the soil indicate that biosolids could be an important source of nitrate in the groundwater recharge. Nitrogen inventories in the soil beneath biosolids-application areas and the nitrogen-input estimates for the study area both support the comparisons of isotopic composition, which indicate that some type of human waste (such as biosolids) and (or) animal manure was the source of nitrate in groundwater sampled from the wells in 2005. The nitrogen-load estimates considered with the nitrogen isotopic data and the soil-nitrogen inventories indicate that biosolids applications likely are a major source of nitrogen to the shallow groundwater at these monitoring wells.

Micro-technology for planetary exploration and education

NASA Technical Reports Server (NTRS)

Miller, David P.; Varsi, Giulio

1991-01-01

The use of combined miniaturization technology and distributed information systems in planetary exploration is discussed. Missions in which teams of microrovers collect samples from planetary surfaces are addressed, emphasizing the ability of rovers to provide coverage of large areas, reliability through redundancy, and participation of a large group of investigators. The latter could involve people from a variety of institutions, increasing the opportunity for wide education and the increased interest of society in general in space exploration. A three-phase program to develop the present approach is suggested.

Soil moisture estimation using reflected solar and emitted thermal infrared radiation

NASA Technical Reports Server (NTRS)

Jackson, R. D.; Cihlar, J.; Estes, J. E.; Heilman, J. L.; Kahle, A.; Kanemasu, E. T.; Millard, J.; Price, J. C.; Wiegand, C. L.

1978-01-01

Classical methods of measuring soil moisture such as gravimetric sampling and the use of neutron moisture probes are useful for cases where a point measurement is sufficient to approximate the water content of a small surrounding area. However, there is an increasing need for rapid and repetitive estimations of soil moisture over large areas. Remote sensing techniques potentially have the capability of meeting this need. The use of reflected-solar and emitted thermal-infrared radiation, measured remotely, to estimate soil moisture is examined.

Climate of the Kennedy Space Center and vicinity

NASA Technical Reports Server (NTRS)

Mailander, Joseph L.

1990-01-01

Climate plays a large role in determining the biota of a region. Summary data are presented for climate variables of ecological importance including precipitation, temperature, evapotranspiration, wind, isolation, lightning, and humidity. The John F. Kennedy Space Center, Cape Canaveral Air Force Station, and surrounding area are sampled intensively for climatic conditions; data are presented for the barrier island, Merritt Island, and the mainland, which represents the range of conditions in the local area. Climatic figures, database listings, and historic data (pre-1931) are presented in the appendix.

Morphological changes in polycrystalline Fe after compression and release

NASA Astrophysics Data System (ADS)

Gunkelmann, Nina; Tramontina, Diego R.; Bringa, Eduardo M.; Urbassek, Herbert M.

2015-02-01

Despite a number of large-scale molecular dynamics simulations of shock compressed iron, the morphological properties of simulated recovered samples are still unexplored. Key questions remain open in this area, including the role of dislocation motion and deformation twinning in shear stress release. In this study, we present simulations of homogeneous uniaxial compression and recovery of large polycrystalline iron samples. Our results reveal significant recovery of the body-centered cubic grains with some deformation twinning driven by shear stress, in agreement with experimental results by Wang et al. [Sci. Rep. 3, 1086 (2013)]. The twin fraction agrees reasonably well with a semi-analytical model which assumes a critical shear stress for twinning. On reloading, twins disappear and the material reaches a very low strength value.

Isolation of organic acids from large volumes of water by adsorption on macroporous resins

USGS Publications Warehouse

Aiken, George R.; Suffet, I.H.; Malaiyandi, Murugan

1987-01-01

Adsorption on synthetic macroporous resins, such as the Amberlite XAD series and Duolite A-7, is routinely used to isolate and concentrate organic acids from forge volumes of water. Samples as large as 24,500 L have been processed on site by using these resins. Two established extraction schemes using XAD-8 and Duolite A-7 resins are described. The choice of the appropriate resin and extraction scheme is dependent on the organic solutes of interest. The factors that affect resin performance, selectivity, and capacity for a particular solute are solution pH, resin surface area and pore size, and resin composition. The logistical problems of sample handling, filtration, and preservation are also discussed.

Large Area Crop Inventory Experiment (LACIE). Second-generation sampling strategy evaluation report. [Kansas, North Dakota, and U.S.S.R.

NASA Technical Reports Server (NTRS)

Basu, J. P. (Principal Investigator); Dragich, S. M.; Mcguigan, D. P.

1978-01-01

The author has identified the following significant results. The stratification procedure in the new sampling strategy for LACIE included: (1) correlation test results indicating that an agrophysical stratum may be homogeneous with respect to agricultural density, but not with respect to wheat density; and (2) agrophysical unit homogeneity test results indicating that with respect to agricultural density many agrophysical units are not homogeneous, but removal of one or more refined strata from any such current agrophysical unit can make the strata homogeneous. The apportioning procedure results indicated that the current procedure is not performing well and that the apportioned estimates of refined strata wheat area are often unreliable.

A sampling procedure to guide the collection of narrow-band, high-resolution spatially and spectrally representative reflectance data. [satellite imagery of earth resources

NASA Technical Reports Server (NTRS)

Brand, R. R.; Barker, J. L.

1983-01-01

A multistage sampling procedure using image processing, geographical information systems, and analytical photogrammetry is presented which can be used to guide the collection of representative, high-resolution spectra and discrete reflectance targets for future satellite sensors. The procedure is general and can be adapted to characterize areas as small as minor watersheds and as large as multistate regions. Beginning with a user-determined study area, successive reductions in size and spectral variation are performed using image analysis techniques on data from the Multispectral Scanner, orbital and simulated Thematic Mapper, low altitude photography synchronized with the simulator, and associated digital data. An integrated image-based geographical information system supports processing requirements.

Strategies for Improving Power in School-Randomized Studies of Professional Development.

PubMed

Kelcey, Ben; Phelps, Geoffrey

2013-12-01

Group-randomized designs are well suited for studies of professional development because they can accommodate programs that are delivered to intact groups (e.g., schools), the collaborative nature of professional development, and extant teacher/school assignments. Though group designs may be theoretically favorable, prior evidence has suggested that they may be challenging to conduct in professional development studies because well-powered designs will typically require large sample sizes or expect large effect sizes. Using teacher knowledge outcomes in mathematics, we investigated when and the extent to which there is evidence that covariance adjustment on a pretest, teacher certification, or demographic covariates can reduce the sample size necessary to achieve reasonable power. Our analyses drew on multilevel models and outcomes in five different content areas for over 4,000 teachers and 2,000 schools. Using these estimates, we assessed the minimum detectable effect sizes for several school-randomized designs with and without covariance adjustment. The analyses suggested that teachers' knowledge is substantially clustered within schools in each of the five content areas and that covariance adjustment for a pretest or, to a lesser extent, teacher certification, has the potential to transform designs that are unreasonably large for professional development studies into viable studies. © The Author(s) 2014.

Monte Carlo and Molecular Dynamics in the Multicanonical Ensemble: Connections between Wang-Landau Sampling and Metadynamics

NASA Astrophysics Data System (ADS)

Vogel, Thomas; Perez, Danny; Junghans, Christoph

2014-03-01

We show direct formal relationships between the Wang-Landau iteration [PRL 86, 2050 (2001)], metadynamics [PNAS 99, 12562 (2002)] and statistical temperature molecular dynamics [PRL 97, 050601 (2006)], the major Monte Carlo and molecular dynamics work horses for sampling from a generalized, multicanonical ensemble. We aim at helping to consolidate the developments in the different areas by indicating how methodological advancements can be transferred in a straightforward way, avoiding the parallel, largely independent, developments tracks observed in the past.

Nanodispersed Suspensions of Zeolite Catalysts for Converting Dimethyl Ether into Olefins

NASA Astrophysics Data System (ADS)

Kolesnichenko, N. V.; Yashina, O. V.; Ezhova, N. N.; Bondarenko, G. N.; Khadzhiev, S. N.

2018-01-01

Nanodispersed suspensions that are effective in DME conversion and stable in the reaction zone in a three-phase system (slurry reactor) are obtained from MFI zeolite commercial samples (TsVM, IK-17-1, and CBV) in liquid media via ultrasonic treatment (UST). It is found that the dispersion medium, in which ultrasound affects zeolite commercial sample, has a large influence on particle size in the suspension. UST in the aqueous medium produces zeolite nanoparticles smaller than 50 nm, while larger particles of MFI zeolite samples form in silicone or hydrocarbon oils. Spectral and adsorption data show that when zeolites undergo UST in an aqueous medium, the acid sites are redistributed on the zeolite surface and the specific surface area of the mesopores increases. Preliminary UST in aqueous media of zeolite commercial samples (TsVM, IK-17-1, and CBV) affects the catalytic properties of MFI zeolite nanodispersed suspensions. The selectivity of samples when paraffins and olefins form is largely due to superacid sites consisting of OH groups of hydroxonium ion H3O+.

Gear comparison for sampling age-0 Mountain Whitefish in the Madison River, Montana

USGS Publications Warehouse

Boyer, Jan K.; Guy, Christopher S.; Webb, Molly A.H.; Horton, Travis B.; McMahon, Thomas E.

2017-01-01

The efficacy of various sampling gears for age-0 Mountain Whitefish Prosopium williamsoni is largely unknown, which makes it difficult to investigate recruitment and early life history dynamics for the species. We compared four gears: seine, backpack electrofisher, minnow trap, and lighted minnow trap. Gears were tested in backwaters, large channels, and small channels in the Madison River, Montana. No age-0 Mountain Whitefish were captured in minnow traps or lighted minnow traps. Mean CPUE of age-0 Mountain Whitefish was higher for seining (0.18 fish/m2; SD, 0.39) than for electrofishing (0.01 fish/m2; SD, 0.03), and the CV was lower for seining. A broader length distribution was sampled by seining (17–41 mm) than with electrofishing (21–36 mm). Age-0 Mountain Whitefish CPUE in seines was highest in backwaters. In channel sites, Mountain Whitefish presence was associated with areas of still or slow water ≥2 m2. Relative to the other sampling gears we evaluated, seining was the most efficient gear for sampling age-0 Mountain Whitefish in a lotic ecosystem.

Diversity and Assembling Processes of Bacterial Communities in Cryoconite Holes of a Karakoram Glacier.

PubMed

Ambrosini, Roberto; Musitelli, Federica; Navarra, Federico; Tagliaferri, Ilario; Gandolfi, Isabella; Bestetti, Giuseppina; Mayer, Christoph; Minora, Umberto; Azzoni, Roberto Sergio; Diolaiuti, Guglielmina; Smiraglia, Claudio; Franzetti, Andrea

2017-05-01

Cryoconite holes are small ponds that form on the surface of glaciers that contain a dark debris, the cryoconite, at the bottom and host active ecological communities. Differences in the structure of bacterial communities have been documented among Arctic and mountain glaciers, and among glaciers in different areas of the world. In this study, we investigated the structure of bacterial communities of cryoconite holes of Baltoro Glacier, a large (62 km in length and 524 km 2 of surface) glacier of the Karakoram, by high-throughput sequencing of the V5-V6 hypervariable regions of the 16S rRNA gene. We found that Betaproteobacteria dominated bacterial communities, with large abundance of genera Polaromonas, probably thanks to its highly versatile metabolism, and Limnohabitans, which may have been favoured by the presence of supraglacial lakes in the area where cryoconite holes were sampled. Variation in bacterial communities among different sampling areas of the glacier could be explained by divergent selective processes driven by variation in environmental conditions, particularly pH, which was the only environmental variable that significantly affected the structure of bacterial communities. This variability may be due to both temporal and spatial patterns of variation in environmental conditions.

DNA Everywhere. A Guide for Simplified Environmental Genomic DNA Extraction Suitable for Use in Remote Areas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gabrielle N. Pecora; Francine C. Reid; Lauren M. Tom

2016-05-01

Collecting field samples from remote or geographically distant areas can be a financially and logistically challenging. With participation of a local organization where the samples are originated from, gDNA samples can be extracted from the field and shipped to a research institution for further processing and analysis. The ability to set up gDNA extraction capabilities in the field can drastically reduce cost and time when running long-term microbial studies with a large sample set. The method outlined here has developed a compact and affordable method for setting up a “laboratory” and extracting and shipping gDNA samples from anywhere in themore » world. This white paper explains the process of setting up the “laboratory”, choosing and training individuals with no prior scientific experience how to perform gDNA extractions and safe methods for shipping extracts to any research institution. All methods have been validated by the Andersen group at Lawrence Berkeley National Laboratory using the Berkeley Lab PhyloChip.« less

Bamboo Classification Using WorldView-2 Imagery of Giant Panda Habitat in a Large Shaded Area in Wolong, Sichuan Province, China.

PubMed

Tang, Yunwei; Jing, Linhai; Li, Hui; Liu, Qingjie; Yan, Qi; Li, Xiuxia

2016-11-22

This study explores the ability of WorldView-2 (WV-2) imagery for bamboo mapping in a mountainous region in Sichuan Province, China. A large area of this place is covered by shadows in the image, and only a few sampled points derived were useful. In order to identify bamboos based on sparse training data, the sample size was expanded according to the reflectance of multispectral bands selected using the principal component analysis (PCA). Then, class separability based on the training data was calculated using a feature space optimization method to select the features for classification. Four regular object-based classification methods were applied based on both sets of training data. The results show that the k -nearest neighbor ( k -NN) method produced the greatest accuracy. A geostatistically-weighted k -NN classifier, accounting for the spatial correlation between classes, was then applied to further increase the accuracy. It achieved 82.65% and 93.10% of the producer's and user's accuracies respectively for the bamboo class. The canopy densities were estimated to explain the result. This study demonstrates that the WV-2 image can be used to identify small patches of understory bamboos given limited known samples, and the resulting bamboo distribution facilitates the assessments of the habitats of giant pandas.

High-contrast X-ray micro-radiography and micro-CT of ex-vivo soft tissue murine organs utilizing ethanol fixation and large area photon-counting detector

PubMed Central

Dudak, Jan; Zemlicka, Jan; Karch, Jakub; Patzelt, Matej; Mrzilkova, Jana; Zach, Petr; Hermanova, Zuzana; Kvacek, Jiri; Krejci, Frantisek

2016-01-01

Using dedicated contrast agents high-quality X-ray imaging of soft tissue structures with isotropic micrometre resolution has become feasible. This technique is frequently titled as virtual histology as it allows production of slices of tissue without destroying the sample. The use of contrast agents is, however, often an irreversible time-consuming procedure and despite the non-destructive principle of X-ray imaging, the sample is usually no longer usable for other research methods. In this work we present the application of recently developed large-area photon counting detector for high resolution X-ray micro-radiography and micro-tomography of whole ex-vivo ethanol-preserved mouse organs. The photon counting detectors provide dark-current-free quantum-counting operation enabling acquisition of data with virtually unlimited contrast-to-noise ratio (CNR). Thanks to the very high CNR even ethanol-only preserved soft-tissue samples without addition of any contrast agent can be visualized in great detail. As ethanol preservation is one of the standard steps of tissue fixation for histology, the presented method can open a way for widespread use of micro-CT with all its advantages for routine 3D non-destructive soft-tissue visualisation. PMID:27461900

Reconnaissance geochemical exploration for gold in the Ad Darb area, Kingdom of Saudi Arabia

USGS Publications Warehouse

Samater, R.M.; Christian, R.P.; Johnson, P.R.; Bookstrom, A.A.

1990-01-01

Overall, metal values in the wadi-sediment samples are low. The known kyanite mineral occurrence is marked by anomalous gold and tin in three minus-80-mesh samples. The low values of the metals do not justify further exploration for the sought deposit type in the immediate vicinity, although the signature of anomalous elements in the wider region is comparable to the signature known in the Carolina Slate Belt, and is permissive of the interpretation that a diffuse hydrothermal system operated in the region during the late Proterozoic. A large concentration of polymetallic anomalies (gold, arsenic, copper, antimony, tin, tungsten, and lead) is outlined in the northeastern part of the survey area on the basis of panned-concentrate samples. The source of the concentration is unknown, and further investigations are recommended. Recommended low-priority investigation of the source of lead and zinc anomalies in the western part of the survey area would be justified as part of a larger program designed to evaluate the mineral potential of the entire belt of Sabya formation rock.

Urban land-use study plan for the National Water-Quality Assessment Program

USGS Publications Warehouse

Squillace, P.J.; Price, C.V.

1996-01-01

This study plan is for Urban Land-Use Studies initiated as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. There are two Urban Land-Use Study objectives: (1) Define the water quality in recharge areas of shallow aquifers underlying areas of new residential and commercial land use in large metropolitan areas, and (2) determine which natural and human factors most strongly affect the occurrence of contaminants in these shallow aquifers. To meet objective 1, each NAWQA Study Unit will install and collect water samples from at least 30 randomly located monitoring wells in a metropolitan area. To meet objective 2, aquifer characteristics and land-use information will be documented. This includes particle-size analysis of each major lithologic unit both in the unsaturated zone and in the aquifer near the water table. The percentage of organic carbon also will be determined for each lithologic unit. Geographic information system coverages will be created that document existing land use around the wells. These data will aid NAWQA personnel in relating natural and human factors to the occurrence of contaminants. Water samples for age dating also will be collected from all monitoring wells, but the samples will be stored until the occurrence of contaminants has been determined. Age-date analysis will be done only on those samples that have no detectable concentrations of anthropogenic contaminants.

Reconnaissance of water quality in the High Plains Aquifer beneath agricultural lands, south-central Kansas

USGS Publications Warehouse

Stullken, L.E.; Stamer, J.K.; Carr, J.E.

1987-01-01

The High Plains of western Kansas was one of 14 areas selected for preliminary groundwater quality reconnaissance by the U.S. Geological Survey 's Toxic Waste--Groundwater Contamination Program. The specific objective was to evaluate the effects of land used for agriculture (irrigated cropland and non-irrigated rangeland) on the water in the High Plains aquifer. Conceptual inferences, based on the information available, would lead one to expect groundwater beneath irrigated cropland to contain larger concentrations of sodium, sulfate, chloride, nitrite plus nitrate, and some water soluble pesticides than water beneath non-irrigated land (range-land) The central part of the Great Bend Prairie, an area of about 1,800 sq mi overlying the High Plains aquifer in south-central Kansas, was selected for the study of agricultural land use because it has sand soils, a shallow water table, relatively large annual precipitation, and includes large areas that are exclusively irrigated cropland or non-irrigated rangeland. As determined by a two-tailed Wilcoxon rank-sum test, concentrations of sodium and alkalinity were significantly larger at the 95% confidence level for water samples from beneath irrigated cropland than from beneath rangeland. No statistically significant difference in concentrations of sulfate, chloride, nitrite plus nitrate, and ammonia, was detected. Concentrations of 2,4-D found in water samples from beneath the rangeland were larger at the 99% confidence level as compared to concentrations of 2,4-D in samples from beneath irrigated cropland. Larger concentrations of sodium and alkalinity were found in water beneath irrigated cropland, and the largest concentration of the pesticide atrazine (triazines were found in three samples) was found in water from the only irrigation well sampled. The sodium and atrazine concentrations found in water from the irrigation well support the premise that water-level drawdown develops under irrigated fields. This diverts the natural groundwater flow patterns, so that pumpage may cause recycling and subsequent concentration of leachates from the land surface. (Author 's abstract)

Identifying sources of groundwater nitrate contamination in a large alluvial groundwater basin with highly diversified intensive agricultural production

NASA Astrophysics Data System (ADS)

Lockhart, K. M.; King, A. M.; Harter, T.

2013-08-01

Groundwater quality is a concern in alluvial aquifers underlying agricultural areas worldwide. Nitrate from land applied fertilizers or from animal waste can leach to groundwater and contaminate drinking water resources. The San Joaquin Valley, California, is an example of an agricultural landscape with a large diversity of field, vegetable, tree, nut, and citrus crops, but also confined animal feeding operations (CAFOs, here mostly dairies) that generate, store, and land apply large amounts of liquid manure. As in other such regions around the world, the rural population in the San Joaquin Valley relies almost exclusively on shallow domestic wells (≤ 150 m deep), of which many have been affected by nitrate. Variability in crops, soil type, and depth to groundwater contribute to large variability in nitrate occurrence across the underlying aquifer system. The role of these factors in controlling groundwater nitrate contamination levels is examined. Two hundred domestic wells were sampled in two sub-regions of the San Joaquin Valley, Stanislaus and Merced (Stan/Mer) and Tulare and Kings (Tul/Kings) Counties. Forty six percent of well water samples in Tul/Kings and 42% of well water samples in Stan/Mer exceeded the MCL for nitrate (10 mg/L NO3-N). For statistical analysis of nitrate contamination, 78 crop and landuse types were considered by grouping them into ten categories (CAFO, citrus, deciduous fruits and nuts, field crops, forage, native, pasture, truck crops, urban, and vineyards). Vadose zone thickness, soil type, well construction information, well proximity to dairies, and dominant landuse near the well were considered. In the Stan/Mer area, elevated nitrate levels in domestic wells most strongly correlate with the combination of very shallow (≤ 21 m) water table and the presence of either CAFO derived animal waste applications or deciduous fruit and nut crops (synthetic fertilizer applications). In Tulare County, statistical data indicate that elevated nitrate levels in domestic well water are most strongly associated with citrus orchards when located in areas with a very shallow (≤ 21 m) water table. Kings County had relatively few nitrate MCL exceedances in domestic wells, probably due to the deeper water table in Kings County.

Fostering Resilience in Beginning Special Education Teachers

ERIC Educational Resources Information Center

Belknap, Bridget M.

2012-01-01

This qualitative study identified perceptions of risk and resilience in four different teaching roles of first-year, secondary special education teachers in three school districts in a large metropolitan area. The study sample consisted of nine women in their first year of teaching who were also completing the requirements of a master's…

Model-assisted estimation of forest resources with generalized additive models

Treesearch

Jean D. Opsomer; F. Jay Breidt; Gretchen G. Moisen; Goran Kauermann

2007-01-01

Multiphase surveys are often conducted in forest inventories, with the goal of estimating forested area and tree characteristics over large regions. This article describes how design-based estimation of such quantities, based on information gathered during ground visits of sampled plots, can be made more precise by incorporating auxiliary information available from...

Investigation of Large Capacity Optical Memories for Correlator Applications.

DTIC Science & Technology

1981-10-01

refringence varies to a certain extent over the area ofeach sample film due to nonuniform stretching during manufacture. Such variations make the...made with the tank placed in a lair ’ c number of positions in the scene -- clearly an excessive burden. Now when the tarets are positioned in the scene

Perry Lake, Delaware River, Kansas, Cultural Resources Sample Survey of Shoreline Areas.

DTIC Science & Technology

1982-09-01

they lived by hunting large ani- mals, now extinct, such as the mammoth, with finely made stone weapons. Paleolithic Period characterized by man’s use...with another stone or with a bone or piece of wood. Petroglyph Inscription or incision on a rock graphic in nature. Photogranmetry The art and

Career Satisfaction Following Technical Education

ERIC Educational Resources Information Center

McDonald, Betty Manager

2011-01-01

The effect of career and technical education in the Caribbean is an area of intervention research that needs more attention. This present research is the first of its kind within the region. The study benefits from a large sample size (N = 500) conducted among a non-traditional population in the field of career development. This paper reports on…

Hopelessness, Family Stress, and Depression among Mexican-Heritage Mothers in the Southwest

ERIC Educational Resources Information Center

Marsiglia, Flavio F.; Kulis, Stephen; Perez, Hilda Garcia; Bermudez-Parsai, Monica

2011-01-01

This article reports on the findings of a study conducted with a sample of 136 Mexican-heritage mothers residing in a large southwestern metropolitan area. From a risk-and-resiliency perspective, hopelessness was approached as a culturally specific response to family stress and other challenges encountered by Mexican immigrants. Although…

A new complete sample of submillijansky radio sources: An optical and near-infrared study

NASA Technical Reports Server (NTRS)

Masci, F.; Condon, J.; Barlow, T.; Lonsdale, C.; Xu, C.; Shupe, D.; Pevunova, O.; Fang, F.; Cutri, R.

2001-01-01

The Very Large Array has been used in C configuration to map an area similar or equal to 0.3 deg(2) at 1.4 GHz with 5 sigma sensitivities of 0.305, 0.325, 0.380, and 0.450 mJy beam(-1)over four equal subareas.

Principals' Perceptions of the Importance of Technology in Schools

ERIC Educational Resources Information Center

Waxman, Hersh C.; Boriack, Anna Witt; Lee, Yuan-Hsuan; MacNeil, Angus

2013-01-01

A sample of 311 principals from a large metropolitan area in the southwest region of the U. S. responded to a questionnaire that addressed public school principals' perceptions related to the major functions of technology in their schools. Principals reported that the major functions of technology were: (a) communication, (b) instruction, (c) data…

Corpus Callosum Area in Children and Adults with Autism

ERIC Educational Resources Information Center

Prigge, Molly B. D.; Lange, Nicholas; Bigler, Erin D.; Merkley, Tricia L.; Neeley, E. Shannon; Abildskov, Tracy J.; Froehlich, Alyson L.; Nielsen, Jared A.; Cooperrider, Jason R.; Cariello, Annahir N.; Ravichandran, Caitlin; Alexander, Andrew L.; Lainhart, Janet E.

2013-01-01

Despite repeated findings of abnormal corpus callosum structure in autism, the developmental trajectories of corpus callosum growth in the disorder have not yet been reported. In this study, we examined corpus callosum size from a developmental perspective across a 30-year age range in a large cross-sectional sample of individuals with autism…

Landscape-scale carbon sampling strategy-lessons learned. Chapter 17

Treesearch

John B. Bradford; Peter Weishampel; Marie-Louise Smith; Randall Kolka; David Y. Hollinger; Richard A. Birdsey; Scott Ollinger; Michael Ryan

2008-01-01

Previous chapters examined individual processes relevant to forest carbon cycling, and characterized measurement approaches for understanding those processes at landscape scales. In this final chapter, we address our overall approach to understanding forest carbon dynamics over large areas. Our objective is to identify any lessons that we learned in the course of...

Mothers' Parenting Dimensions and Adolescent Externalizing and Internalizing Behaviors in a Low-Income, Urban Mexican American Sample

ERIC Educational Resources Information Center

Manongdo, Jennifer A.; Garcia, Jorge I. Ramirez

2007-01-01

The relation between adolescent-reported parenting behaviors and mother-reported youth externalizing and internalizing behaviors was examined among 91 Mexican American mother-adolescent (ages 13-17) dyads recruited from an immigrant enclave in a large midwestern metropolitan area. Two major dimensions of mothers' parenting emerged: supportive…

Educational Interests of Disadvantaged and Non-Disadvantaged Iowa Household Heads.

ERIC Educational Resources Information Center

Arendt, Donald Philip

A study was made of 538 disadvantaged and 247 non-disadvantaged household heads in Iowa -- their occupation, training desired, material possessions, membership and participation. The sample included 643 males and 142 females and was distributed in zones from open country to large urban areas. According to the prescribed criteria 14% of the…

Search for Cosmic-Ray Electron and Positron Anisotropies with Seven Years of Fermi Large Area Telescope Data

DOE PAGES

Abdollahi, S.; Ackermann, M.; Ajello, M.; ...

2017-03-01

We present the Large Area Telescope on board the Fermi Gamma-ray Space Telescope that has collected the largest ever sample of high-energy cosmic-ray electron and positron events since the beginning of its operation. Potential anisotropies in the arrival directions of cosmic-ray electrons or positrons could be a signature of the presence of nearby sources. We use almost seven years of data with energies above 42 GeV processed with the Pass 8 reconstruction. The present data sample can probe dipole anisotropies down to a level of 10 -3. We take into account systematic effects that could mimic true anisotropies at thismore » level. We present a detailed study of the event selection optimization of the cosmic-ray electrons and positrons to be used for anisotropy searches. Since no significant anisotropies have been detected on any angular scale, we present upper limits on the dipole anisotropy. Lastly, the present constraints are among the strongest to date probing the presence of nearby young and middle-aged sources.« less

Hydrologic data, 1974-77, Stovepipe Wells Hotel area, Death Valley National Monument, Inyo County, California

USGS Publications Warehouse

Lamb, Charles Edwin; Downing, D.J.

1979-01-01

Ground-water levels in most wells did not change significantly from 1974 to 1977 in the Stovepipe Wells Hotel area, California. The average water-level decline was less than 0.10 foot between August 1974 and August 1977 in 10 observation wells. Water-level contours show a depression centered on the two pumping wells, but this depression existed before the National Park Service started pumping its well. The chemical quality of the ground water is poor. Dissolved-solids concentrations in water samples ranged from 2,730 to 6,490 milligrams per liter. Analyses of water samples from two wells showed large changes in some constituents from 1976 to 1977. Streamflow in Salt Creek has been monitored since February 1974. Base flow is seasonal, being 0.10 to 0.20 cubic foot per second during the summer and as much as three times that amount during the winter. Two chemical analyses of water from Salt Creek, representing summer and winter flow conditions, show large differences for many constituents. (Woodard-USGS)

Hydrology and Ground-Water Quality in the Mine Workings within the Picher Mining District, Northeastern Oklahoma, 2002-03

USGS Publications Warehouse

DeHay, Kelli L.; Andrews, William J.; Sughru, Michael P.

2004-01-01

The Picher mining district of northeastern Ottawa County, Oklahoma, was a major site of mining for lead and zinc ores in the first half of the 20th century. The primary source of lead and zinc were sulfide minerals disseminated in the cherty limestones and dolomites of the Boone Formation of Mississippian age, which comprises the Boone aquifer. Ground water in the aquifer and seeping to surface water in the district has been contaminated by sulfate, iron, lead, zinc, and several other metals. The U.S. Geological Survey, in cooperation with the Oklahoma Department of Environmental Quality, investigated hydrology and ground-water quality in the mine workings in the mining district, as part of the process to aid water managers and planners in designing remediation measures that may restore the environmental quality of the district to pre-mining conditions. Most ground-water levels underlying the mining district had similar altitudes, indicating a large degree of hydraulic connection in the mine workings and overlying aquifer materials. Recharge-age dates derived from concentrations of chlorofluorocarbons and other dissolved gases indicated that water in the Boone aquifer may flow slowly from the northeast and southeast portions of the mining district. However, recharge-age dates may have been affected by the types of sites sampled, with more recent recharge-age dates being associated with mine-shafts, which are more prone to atmospheric interactions and surface runoff than the sampled airshafts. Water levels in streams upstream from the confluence of Tar and Lytle Creeks were several feet higher than those in adjacent portions of the Boone aquifer, perhaps due to low-permeability streambed sediments and indicating the streams may be losing water to the aquifer in this area. From just upstream to downstream from the confluence of Tar and Lytle Creeks, surface-water elevations in these streams were less than those in the surrounding Boone aquifer, indicating that seepage from the aquifer to downstream portions of Tar Creek was much more likely. Water properties and major-ion concentrations indicate that water in the mining area was very hard, with large concentrations of dissolved solids that increased from areas of presumed recharge toward areas with older ground water. Most of the ground-water samples, particularly those from the airshafts, had dissolved-oxygen concentrations less than 1.0 milligram per liter. Small concentrations of dissolved oxygen may have been introduced during the sampling process. The small dissolved-oxygen concentrations were associated with samples containing large iron concentrations that indicates possible anoxic conditions in much of the aquifer. Ground water in the mining district was dominated by calcium, magnesium, and sulfate. Sodium concentrations tended to increase relative to calcium and magnesium concentrations. Ground-water samples collected in 2002-03 had large concentrations of many trace elements. Larger concentrations of metals and sulfate occurred in ground water with smaller pHs and dissolved-oxygen concentrations. Iron was the metal with the largest concentrations in the ground-water samples, occurring at concentrations up to 115,000 micrograms per liter. Cadmium, lead, manganese, zinc, and the other analyzed metals occurred in smaller concentrations in ground water than iron. However, larger cadmium concentrations appeared to be associated with sites that have small iron concentrations and more oxygenated waters. This is noteworthy because the small sulfate and iron concentrations in these waters could lead to conclusions that the waters are less contaminated than waters with large sulfate and iron concentrations. Ground-water quality in the mining district was compared with subsets of samples collected in 1983-85 and in 2002. Concentrations of most mine-water indicators such as specific conductance, acidity, magnesium, sulfate, and trace elements concentrations dec

Reconnaissance investigation of water quality, bottom sediment, and biota associated with irrigation drainage in the Owyhee and Vale Projects, Oregon and Idaho, 1990-91

USGS Publications Warehouse

Rinella, F.A.; Mullins, W.H.; Schuler, C.A.

1994-01-01

A reconnaissance investigation was conducted during 1990--91 in the Owyhee and Vale projects in eastern Oregon and southwestern Idaho, as well as at a number of sites in the Snake River and tributaries to the Snake River in the area of study. The objective of the study was to determine if agricultural drainwater entering the study area was causing, or had the potential to cause, significant harmful effects to human health, fish and wildlife, or may adversely affect the suitability of water for beneficial uses. Approximately 153,000 acres of land are irrigated annually within the areas of the Owyhee and Vale projects. Large quantities of water are required because of the semiarid climate and relatively high evaporation rates. Several reservoirs in the area are filled annually during the wet, nonirrigation season to sustain irrigation during the dry summer months. During the irrigation season, this impounded water, along with direct diversions from the Malheur, Owyhee, and Snake Rivers, is transported to the irrigated areas through a series of diversion tunnels, siphons, canals, aqueducts, ditches, and drains. Major crops grown in the area include sugar beets, alfalfa hay and other hay crops, onions, and winter wheat. Minor crops include corn, potatoes, mint, various seed crops, and fruit. In 1987, it was estimated that the following amounts of pesticides were used in the project areas: 2,4-D (21,000 lbs [pounds]), chlorpyrifos (1,000 lbs), dacthal (40,000 lbs), dicamba (320 lbs), endosulfan (2,500 lbs), ethion (11,000 lbs), malathion (24,000 lbs), parathion (5,000 lbs), and phorate (11,000 lbs). Median concentrations and values for total dissolved solids, alkalinity, sodium adsorption ratio, and hardness in the Vale project area were greater than 1.5 times those values observed in the Owyhee project area or at other Snake River locations. During irrigation (August 1990), total dissolved solids, alkalinity, sodium adsorption ratio, and hardness values increased in a downstream manner. Constituent values at drainwater sites generally were comparable to concentrations below the irrigated ureas in the Owyhee and Vale project areas. The trace elements arsenic, boron, copper, molybdenum, vanadium, and zinc were detected in most water samples; cadmium, chromium, lead, and selenium were detected in some samples at concentrations generally near the analytical reporting limit; mercury was not detected in any samples. In some water samples, concentrations of arsenic, boron, cadmium, copper, and lead exceeded State or Federal water-quality standards or criteria. Most trace elements in bottom sediment were detected at concentrations within the expected 95-percent baseline range for soils from the Western United States. Concentrations that exceeded the 95-percent baseline range for study area soils were: (1) arsenic and lead in one sample from a site in the Vale project area; (2) mercury, lead, and tin in one sample from a site in the Snake River system; (3) manganese in two samples from two sites in the Snake River system; and (4) manganese from one sample from a site in the Vale project area. Fifteen pesticides and metabolites were detected in whole-water samples collected from sites in the study area. DDT, plus its metabolites (DDE and DDD), dieldrin, endrin, 2,4-D, dicamba, and dacthal were detected in samples collected from seven or more sites. Other pesticides detected included chlorpyrifos, endosulfan, ethion, malathion, parathion, phorate, and lindane. Most of the detected pesticide concentrations generally were largest in drainwater and at the most downstream sampling locations in the Owyhee and Vale project areas. Concentrations exceeded water-quality criteria established for the protection of freshwater aquatic life in 86 percent of the whole-water samples analyzed for DDT plus its metabolites, 71 percent of the dieldrin samples, 14 percent of the endrin samples, and 10 percent of the parathion samples. Eight pesticides and

Spatial-temporal Trends and Factors Associated with the Bluetongue Virus Seropositivity in Large Game Hunting Areas from Southern Spain.

PubMed

Arenas-Montes, A; Paniagua, J; Arenas, A; Lorca-Oró, C; Carbonero, A; Cano-Terriza, D; García-Bocanegra, I

2016-10-01

An epidemiological study was carried out to determine the spatial-temporal trends and risk factors potentially involved in the seropositivity to bluetongue virus (BTV) in hunting areas with presence of red deer (Cervus elaphus). A total of 60 of 98 (61.2%; CI95% : 51.6-70.9) hunting areas sampled presented at least one seropositive red deer. Antibodies against BTV were detected in juvenile animals during the hunting seasons 2007/2008 to 2013/2014 in 15 of 98 (15.3%) hunting areas, which indicates an uninterrupted circulation of BTV in this period. A multivariate logistic regression model showed that the red deer density at hunting area level (>22 individuals/km(2) ), the annual abundance of Culicoides imicola (>1.4 mosquitoes/sampling) and the goat density at municipality level (>24.1 individuals/km(2) ) were factors significantly associated with BTV seropositivity in hunting areas. Control measures against BTV in the studied area include vaccination programmes in wild and domestic ruminants, movement control in areas with high densities and abundance of red deer and C. imicola, respectively. Considering the potential risk of BTV re-emergence, red deer should be included in the BT surveillance programmes in regions where these species share habitats with livestock. © 2014 Blackwell Verlag GmbH.

Analysis of environmental setting, surface-water and groundwater data, and data gaps for the Citizen Potawatomi Nation Tribal Jurisdictional Area, Oklahoma, through 2011

USGS Publications Warehouse

Andrews, William J.; Harich, Christopher R.; Smith, S. Jerrod; Lewis, Jason M.; Shivers, Molly J.; Seger, Christian H.; Becker, Carol J.

2013-01-01

The Citizen Potawatomi Nation Tribal Jurisdictional Area, consisting of approximately 960 square miles in parts of three counties in central Oklahoma, has an abundance of water resources, being underlain by three principal aquifers (alluvial/terrace, Central Oklahoma, and Vamoosa-Ada), bordered by two major rivers (North Canadian and Canadian), and has several smaller drainages. The Central Oklahoma aquifer (also referred to as the Garber-Wellington aquifer) underlies approximately 3,000 square miles in central Oklahoma in parts of Cleveland, Logan, Lincoln, Oklahoma, and Pottawatomie Counties and much of the tribal jurisdictional area. Water from these aquifers is used for municipal, industrial, commercial, agricultural, and domestic supplies. The approximately 115,000 people living in this area used an estimated 4.41 million gallons of fresh groundwater, 12.12 million gallons of fresh surface water, and 8.15 million gallons of saline groundwater per day in 2005. Approximately 8.48, 2.65, 2.24, 1.55, 0.83, and 0.81 million gallons per day of that water were used for domestic, livestock, commercial, industrial, crop irrigation, and thermoelectric purposes, respectively. Approximately one-third of the water used in 2005 was saline water produced during petroleum production. Future changes in use of freshwater in this area will be affected primarily by changes in population and agricultural practices. Future changes in saline water use will be affected substantially by changes in petroleum production. Parts of the area periodically are subject to flooding and severe droughts that can limit available water resources, particularly during summers, when water use increases and streamflows substantially decrease. Most of the area is characterized by rural types of land cover such as grassland, pasture/hay fields, and deciduous forest, which may limit negative effects on water quality by human activities because of lesser emissions of man-made chemicals on such areas than in more urbanized areas. Much of the water in the area is of good quality, though some parts of this area have water quality impaired by very hard surface water and groundwater; large chloride concentrations in some smaller streams; relatively large concentrations of nutrients and counts of fecal-indicator bacteria in the North Canadian River; and chloride, iron, manganese, and uranium concentrations that exceed primary or secondary drinking-water standards in water samples collected from small numbers of wells. Substantial amounts of hydrologic and water-quality data have been collected in much of this area, but there are gaps in those data caused by relatively few streamflow-gaging stations, uneven distribution of surface-water quality sampling sites, lack of surface-water quality sampling at high-flow and low-flow conditions, and lack of a regularly measured and sampled groundwater network. This report summarizes existing water-use, climatic, geographic, hydrologic, and water-quality data and describes several means of filling gaps in hydrologic data for this area.

Archeointensity determinations on Pre-Columbian potteries from La Ceiba and Santa Marta shelter-caves (Chiapas, Mexico).

NASA Astrophysics Data System (ADS)

Rodriguez-Ceja, Maria; Camps, Pierre; Goguitchaichvili, Avto; Poidras, Thierry; Nicol, Patrick

2014-05-01

Quite surprisingly, the abundance of archaeological baked clays found in the tropical area of Mesoamerica contrast with the small amount of archeomagnetic data available today for this area [Fanjat et al, EPSL, 2013; Alva-Valdivia et al, PEPI, 2010, Morales et al., EPS, 2009]. It seems especially difficult to try to establish a regional trend in the intensity variations. While they are few, the data are moreover of uneven quality as attested by a large scatter in experimental values during the Mesoamerican classic and post-classic periods (250-1521 AD) that cannot be explained by real fluctuations in the Earth's magnetic field [Fanjat et al, EPSL, 2013]. The present study is part of a large effort to provide reliable and perfectly dated archeointensity data for the tropical area of Mesoamerica. It focuses on Thellier-Thellier archeointensity measurements obtained from 87 small fragments from potsherds of 12 different potteries. These potteries were excavated from sedimentary sequences within two shelter-caves, La Ceiba and Santa Marta, located on the banks of Grijalva and La Venta rivers, respectively. Both are shelter-caves without constructed structures that were inhabited by humans groups. Samples were located in different stratigraphic levels, culturally well identified and well preserved due to long time sedimentation. Only samples with a homogenous color were pre-selected for the rock magnetic study performed prior to any attempt to estimate the archeointensity. This was done in order to assure, as far as possible, a uniform baking during the manufacture, which is supposed to be made in open sky fire, since no kiln construction has been found. The ceramics ages were achieved in 2 ways: for samples with organic material associated, a 14C dating was done. The rest of the samples were dated according to their typological characteristics, comparing with regional ceramic chronological classification. This includes characteristics such as the finishing surface type, decoration, polished type, color, clay characteristics, composition, baking types, form, and function. The ages of the selected samples enclose the entire classical and post-classical periods. Most of our selected samples yielded good, from a technical point of view, archeointensity estimates. These new archeointensity determinations are compared and discussed with the previous values obtained for this area.

Water-quality assessment of the Rio Grande Valley, Colorado, New Mexico, and Texas : shallow ground-water quality and land use in the Albuquerque area, central New Mexico, 1993

USGS Publications Warehouse

Anderholm, Scott K.

1997-01-01

This report describes the quality of shallow ground water and the relations between land use and the quality of that shallow ground water in an urban area in and adjacent to Albuquerque, New Mexico. Water samples were collected from 24 shallow wells. Samples were analyzed for selected common constituents, nutrients, trace elements, radionuclides, volatile organic compounds, and pesticides. The study area, which is in the Albuquerque Basin in central New Mexico, was limited to the Rio Grande flood plain; depth to water in this area generally is less than 25 feet. The amount and composition of recharge to the shallow ground-water system are important factors that affect shallow ground-water composition in this area. Important sources of recharge that affect shallow ground-water quality in the area include infiltration of surface water, which is used in agricultural land-use areas to irrigate crops, and infiltration of septic-system effluent in residential areas. Agricultural land use represents about 28 percent of the area, and residential land use represents about 35 percent of the total study area. In most of the study area, agricultural land use is interspersed with residential land use and neither is the dominant land use in the area. Land use in the study area historically has been changing from agricultural to urban. The composition of shallow ground water in the study area varies considerably. The dissolved solids concentration in shallow ground water in the study area ranges from 272 to 1,650 milligrams per liter, although the relative percentages of selected cations and anions do not vary substantially. Calcium generally is the dominant cation and bicarbonate generally is the dominant anion. Concentrations of nutrients generally were less than 1 milligram per liter. The concentration of many trace elements in shallow ground water was below or slightly above 1 microgram per liter and there was little variation in the concentrations. Barium, iron, manganese, molybdenum, and uranium were the only trace elements analyzed for that had median concentrations greater than 5 micrograms per liter. Volatile organic compounds were detected in 5 of 24 samples. Cis-1,2-dichloroethene and 1,1-dichloroethane were the most commonly detected volatile organic compounds (detected in two samples each). Pesticides were detected in 8 of 24 samples. Prometon was the most commonly detected pesticide (detected in 5 of 24 samples). Concentrations of volatile organic compounds and pesticides detected were much smaller than any U.S. Environmental Protection Agency standards that have been established. Infiltration of surface water and the evaporation or transpiration of this water, which partially is the result of past and present agricultural land use, seem to affect the concentrations of common constituents in shallow ground water in the study area. The small excess chloride in shallow ground water relative to surface water that has been affected by evaporation or transpiration could be due to mixing of shallow ground water with small amounts of precipitation/bulk deposition or septic-system effluent. Infiltration of septic-system effluent (residential land use) has affected the shallow ground-water composition in parts of the study area on the basis of the small dissolved oxygen concentrations, large dissolved organic carbon concentrations, and excess chloride. Despite the loading of nitrogen to the shallow ground-water system as the result of infiltration of septic-system effluent, the small nitrogen concentrations in shallow ground water probably are due to the small dissolved oxygen concentrations and relatively large dissolved organic carbon concentrations. The small concentrations and lack of variation of most trace elements indicate that land use has not substantially affected the concentration

A modified Wald interval for the area under the ROC curve (AUC) in diagnostic case-control studies

PubMed Central

2014-01-01

Background The area under the receiver operating characteristic (ROC) curve, referred to as the AUC, is an appropriate measure for describing the overall accuracy of a diagnostic test or a biomarker in early phase trials without having to choose a threshold. There are many approaches for estimating the confidence interval for the AUC. However, all are relatively complicated to implement. Furthermore, many approaches perform poorly for large AUC values or small sample sizes. Methods The AUC is actually a probability. So we propose a modified Wald interval for a single proportion, which can be calculated on a pocket calculator. We performed a simulation study to compare this modified Wald interval (without and with continuity correction) with other intervals regarding coverage probability and statistical power. Results The main result is that the proposed modified Wald intervals maintain and exploit the type I error much better than the intervals of Agresti-Coull, Wilson, and Clopper-Pearson. The interval suggested by Bamber, the Mann-Whitney interval without transformation and also the interval of the binormal AUC are very liberal. For small sample sizes the Wald interval with continuity has a comparable coverage probability as the LT interval and higher power. For large sample sizes the results of the LT interval and of the Wald interval without continuity correction are comparable. Conclusions If individual patient data is not available, but only the estimated AUC and the total sample size, the modified Wald intervals can be recommended as confidence intervals for the AUC. For small sample sizes the continuity correction should be used. PMID:24552686

A modified Wald interval for the area under the ROC curve (AUC) in diagnostic case-control studies.

PubMed

Kottas, Martina; Kuss, Oliver; Zapf, Antonia

2014-02-19

The area under the receiver operating characteristic (ROC) curve, referred to as the AUC, is an appropriate measure for describing the overall accuracy of a diagnostic test or a biomarker in early phase trials without having to choose a threshold. There are many approaches for estimating the confidence interval for the AUC. However, all are relatively complicated to implement. Furthermore, many approaches perform poorly for large AUC values or small sample sizes. The AUC is actually a probability. So we propose a modified Wald interval for a single proportion, which can be calculated on a pocket calculator. We performed a simulation study to compare this modified Wald interval (without and with continuity correction) with other intervals regarding coverage probability and statistical power. The main result is that the proposed modified Wald intervals maintain and exploit the type I error much better than the intervals of Agresti-Coull, Wilson, and Clopper-Pearson. The interval suggested by Bamber, the Mann-Whitney interval without transformation and also the interval of the binormal AUC are very liberal. For small sample sizes the Wald interval with continuity has a comparable coverage probability as the LT interval and higher power. For large sample sizes the results of the LT interval and of the Wald interval without continuity correction are comparable. If individual patient data is not available, but only the estimated AUC and the total sample size, the modified Wald intervals can be recommended as confidence intervals for the AUC. For small sample sizes the continuity correction should be used.

Spatial Distribution and Site-Specific Spraying of Main Sucking Pests of Elm Trees.

PubMed

Karimzadeh, R; Iranipour, S

2017-06-01

Elm trees are important landscape trees and sucking insects weaken the elm trees and produce large amounts of honeydew. The main objectives of this study were to identify main honeydew-producing pests of elm trees and do site-specific spraying against these pests. To map the spatial distribution of the sucking pests in the large scale, the study area was divided into 40 × 40 m grids and one tree was chosen randomly from each grid (a total of 55 trees). These trees were sampled twice a year in 2011 and 2012. Each sample was a 30-cm branch terminal. Eight samples were taken from each tree in four cardinal directions and two canopy levels. The number of sucking insects and leaves of each sample were counted and recorded. Spatial analysis of the data was carried out using geostatistics. Kriging was used for producing prediction maps. Insecticide application was restricted to the regions with populations higher than threshold. To identify within-tree distribution of the honeydew-producing pests, six and four elm trees were chosen in 2011 and 2012 respectively, and sampled weekly. These trees were sampled as described previously. European elm scale (EES), Gossyparia spuria (Modeer) and two species of aphids were the dominant honeydew-producing pests. The results revealed that the effects of direction, canopy level and their interactions on insect populations were not statistically significant (P < 0.05). Site-specific spraying decreased the amount of insecticides used by ca. 20%, while satisfactory control of the sucking pests and honeydew excretion was obtained. Considering the environmental and economic benefits of site-specific spraying, it is worth doing more complementary works in this area.

Field Tests of Real-time In-situ Dissolved CO2 Monitoring for CO2 Leakage Detection in Groundwater

NASA Astrophysics Data System (ADS)

Yang, C.; Zou, Y.; Delgado, J.; Guzman, N.; Pinedo, J.

2016-12-01

Groundwater monitoring for detecting CO2 leakage relies on groundwater sampling from water wells drilled into aquifers. Usually groundwater samples are required be collected periodically in field and analyzed in the laboratory. Obviously groundwater sampling is labor and cost-intensive for long-term monitoring of large areas. Potential damage and contamination of water samples during the sampling process can degrade accuracy, and intermittent monitoring may miss changes in the geochemical parameters of groundwater, and therefore signs of CO2 leakage. Real-time in-situ monitoring of geochemical parameters with chemical sensors may play an important role for CO2 leakage detection in groundwater at a geological carbon sequestration site. This study presents field demonstration of a real-time in situ monitoring system capable of covering large areas for detection of low levels of dissolved CO2 in groundwater and reliably differentiating natural variations of dissolved CO2 concentration from small changes resulting from leakage. The sand-alone system includes fully distributed fiber optic sensors for carbon dioxide detection with a unique sensor technology developed by Intelligent Optical Systems. The systems were deployed to the two research sites: the Brackenridge Field Laboratory where the aquifer is shallow at depths of 10-20 ft below surface and the Devine site where the aquifer is much deeper at depths of 140 to 150 ft. Groundwater samples were periodically collected from the water wells which were installed with the chemical sensors and further compared to the measurements of the chemical sensors. Our study shows that geochemical monitoring of dissolved CO2 with fiber optic sensors could provide reliable CO2 leakage signal detection in groundwater as long as CO2 leakage signals are stronger than background noises at the monitoring locations.

SUBSTRUCTURE WITHIN THE SSA22 PROTOCLUSTER AT z ≈ 3.09

DOE Office of Scientific and Technical Information (OSTI.GOV)

Topping, Michael W.; Shapley, Alice E.; Steidel, Charles C., E-mail: mtopping@astro.ucla.edu

We present the results of a densely sampled spectroscopic survey of the SSA22 protocluster at z ≈ 3.09. Our sample with Keck/LRIS spectroscopy includes 106 Ly α emitters (LAEs) and 40 Lyman break galaxies (LBGs) at z = 3.05–3.12. These galaxies are contained within the 9′ × 9′ region in which the protocluster was discovered, which also hosts the maximum galaxy overdensity in the SSA22 region. The redshift histogram of our spectroscopic sample reveals two distinct peaks, at z = 3.069 (blue; 43 galaxies) and z = 3.095 (red; 103 galaxies). Furthermore, objects in the blue and red peaks aremore » segregated on the sky, with galaxies in the blue peak concentrating toward the western half of the field. These results suggest that the blue and red redshift peaks represent two distinct structures in physical space. Although the double-peaked redshift histogram is traced in the same manner by LBGs and LAEs, and brighter and fainter galaxies, we find that 9 out of 10 X-ray AGNs in SSA22, and all 7 spectroscopically confirmed giant Ly α “blobs,” reside in the red peak. We combine our data set with sparsely sampled spectroscopy from the literature over a significantly wider area, finding preliminary evidence that the double-peaked structure in redshift space extends beyond the region of our dense spectroscopic sampling. In order to fully characterize the three-dimensional structure, dynamics, and evolution of large-scale structure in the SSA22 overdensity, we require the measurement of large samples of LAE and LBG redshifts over a significantly wider area, as well as detailed comparisons with cosmological simulations of massive cluster formation.« less

Enhancing fish Underwater Visual Census to move forward assessment of fish assemblages: An application in three Mediterranean Marine Protected Areas

PubMed Central

Thiriet, Pierre; Di Franco, Antonio; Francour, Patrice

2017-01-01

Monitoring fish assemblages is needed to assess whether Marine Protected Areas (MPAs) are meeting their conservation and fisheries management goals, as it allows one to track the progress of recovery of exploited species and associated communities. Underwater Visual Census techniques (UVC) are used to monitor fish assemblages in MPAs. UVCs should be adapted to fish abundance, body-size and behaviour, which can strongly affect fish detectability. In Mediterranean subtidal habitats, however, UVC strip transects of one surface area (25x5 m2) are commonly used to survey the whole fish assemblage, from large shy fish to small crypto-benthic fish. Most high trophic level predators (HTLPs) are large shy fish which rarely swim close to divers and, consequently, their abundance may be under-estimated with commonly used transects. Here, we propose an improvement to traditional transect surveys to better account for differences in behaviour among and within species. First, we compared the effectiveness of combining two transect surface areas (large: 35x20 m2; medium: 25x5 m2) in quantifying large, shy fish within and outside Mediterranean MPAs. We identified species-specific body-size thresholds defining a smaller and a larger size class better sampled by medium and large transects respectively. Combining large and medium transects provided more accurate biomass and species richness estimates for large, shy species than using medium transects alone. We thus combined the new approach with two other transect surface areas commonly used to survey crypto-benthic (10x1 m2) and necto-benthic (25x5 m2) species in order to assess how effectively MPAs protection the whole fish assemblage. We verified that MPAs offer significant protection for HTLPs, their response in terms of biomass and density increase in MPAs was always higher in magnitude than other functional groups. Inside MPAs, the contribution of HTLP reached >25% of total fish biomass, against < 2% outside MPAs. Surveys with multiple transect surface areas allow for a more realistic assessment of the structure of the whole fish assemblage and better assessment of potential recovery of HTLPs within reserves of HTLP. PMID:28594836

Enhancing fish Underwater Visual Census to move forward assessment of fish assemblages: An application in three Mediterranean Marine Protected Areas.

PubMed

Prato, Giulia; Thiriet, Pierre; Di Franco, Antonio; Francour, Patrice

2017-01-01

Monitoring fish assemblages is needed to assess whether Marine Protected Areas (MPAs) are meeting their conservation and fisheries management goals, as it allows one to track the progress of recovery of exploited species and associated communities. Underwater Visual Census techniques (UVC) are used to monitor fish assemblages in MPAs. UVCs should be adapted to fish abundance, body-size and behaviour, which can strongly affect fish detectability. In Mediterranean subtidal habitats, however, UVC strip transects of one surface area (25x5 m2) are commonly used to survey the whole fish assemblage, from large shy fish to small crypto-benthic fish. Most high trophic level predators (HTLPs) are large shy fish which rarely swim close to divers and, consequently, their abundance may be under-estimated with commonly used transects. Here, we propose an improvement to traditional transect surveys to better account for differences in behaviour among and within species. First, we compared the effectiveness of combining two transect surface areas (large: 35x20 m2; medium: 25x5 m2) in quantifying large, shy fish within and outside Mediterranean MPAs. We identified species-specific body-size thresholds defining a smaller and a larger size class better sampled by medium and large transects respectively. Combining large and medium transects provided more accurate biomass and species richness estimates for large, shy species than using medium transects alone. We thus combined the new approach with two other transect surface areas commonly used to survey crypto-benthic (10x1 m2) and necto-benthic (25x5 m2) species in order to assess how effectively MPAs protection the whole fish assemblage. We verified that MPAs offer significant protection for HTLPs, their response in terms of biomass and density increase in MPAs was always higher in magnitude than other functional groups. Inside MPAs, the contribution of HTLP reached >25% of total fish biomass, against < 2% outside MPAs. Surveys with multiple transect surface areas allow for a more realistic assessment of the structure of the whole fish assemblage and better assessment of potential recovery of HTLPs within reserves of HTLP.

Molecular epidemiology biomarkers-Sample collection and processing considerations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, Nina T.; Pfleger, Laura; Berger, Eileen

2005-08-07

Biomarker studies require processing and storage of numerous biological samples with the goals of obtaining a large amount of information and minimizing future research costs. An efficient study design includes provisions for processing of the original samples, such as cryopreservation, DNA isolation, and preparation of specimens for exposure assessment. Use of standard, two-dimensional and nanobarcodes and customized electronic databases assure efficient management of large sample collections and tracking results of data analyses. Standard operating procedures and quality control plans help to protect sample quality and to assure validity of the biomarker data. Specific state, federal and international regulations are inmore » place regarding research with human samples, governing areas including custody, safety of handling, and transport of human samples. Appropriate informed consent must be obtained from the study subjects prior to sample collection and confidentiality of results maintained. Finally, examples of three biorepositories of different scale (European Cancer Study, National Cancer Institute and School of Public Health Biorepository, University of California, Berkeley) are used to illustrate challenges faced by investigators and the ways to overcome them. New software and biorepository technologies are being developed by many companies that will help to bring biological banking to a new level required by molecular epidemiology of the 21st century.« less

Identification of proteomic biomarkers predicting prostate cancer aggressiveness and lethality despite biopsy-sampling error.

PubMed

Shipitsin, M; Small, C; Choudhury, S; Giladi, E; Friedlander, S; Nardone, J; Hussain, S; Hurley, A D; Ernst, C; Huang, Y E; Chang, H; Nifong, T P; Rimm, D L; Dunyak, J; Loda, M; Berman, D M; Blume-Jensen, P

2014-09-09

Key challenges of biopsy-based determination of prostate cancer aggressiveness include tumour heterogeneity, biopsy-sampling error, and variations in biopsy interpretation. The resulting uncertainty in risk assessment leads to significant overtreatment, with associated costs and morbidity. We developed a performance-based strategy to identify protein biomarkers predictive of prostate cancer aggressiveness and lethality regardless of biopsy-sampling variation. Prostatectomy samples from a large patient cohort with long follow-up were blindly assessed by expert pathologists who identified the tissue regions with the highest and lowest Gleason grade from each patient. To simulate biopsy-sampling error, a core from a high- and a low-Gleason area from each patient sample was used to generate a 'high' and a 'low' tumour microarray, respectively. Using a quantitative proteomics approach, we identified from 160 candidates 12 biomarkers that predicted prostate cancer aggressiveness (surgical Gleason and TNM stage) and lethal outcome robustly in both high- and low-Gleason areas. Conversely, a previously reported lethal outcome-predictive marker signature for prostatectomy tissue was unable to perform under circumstances of maximal sampling error. Our results have important implications for cancer biomarker discovery in general and development of a sampling error-resistant clinical biopsy test for prediction of prostate cancer aggressiveness.

Evaluating noninvasive genetic sampling techniques to estimate large carnivore abundance.

PubMed

Mumma, Matthew A; Zieminski, Chris; Fuller, Todd K; Mahoney, Shane P; Waits, Lisette P

2015-09-01

Monitoring large carnivores is difficult because of intrinsically low densities and can be dangerous if physical capture is required. Noninvasive genetic sampling (NGS) is a safe and cost-effective alternative to physical capture. We evaluated the utility of two NGS methods (scat detection dogs and hair sampling) to obtain genetic samples for abundance estimation of coyotes, black bears and Canada lynx in three areas of Newfoundland, Canada. We calculated abundance estimates using program capwire, compared sampling costs, and the cost/sample for each method relative to species and study site, and performed simulations to determine the sampling intensity necessary to achieve abundance estimates with coefficients of variation (CV) of <10%. Scat sampling was effective for both coyotes and bears and hair snags effectively sampled bears in two of three study sites. Rub pads were ineffective in sampling coyotes and lynx. The precision of abundance estimates was dependent upon the number of captures/individual. Our simulations suggested that ~3.4 captures/individual will result in a < 10% CV for abundance estimates when populations are small (23-39), but fewer captures/individual may be sufficient for larger populations. We found scat sampling was more cost-effective for sampling multiple species, but suggest that hair sampling may be less expensive at study sites with limited road access for bears. Given the dependence of sampling scheme on species and study site, the optimal sampling scheme is likely to be study-specific warranting pilot studies in most circumstances. © 2015 John Wiley & Sons Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broxton, D.E.

A total of 338 water and 1877 sediment samples were collected over a 20,700-km/sup 2/ area from 2125 locations at a nominal density of one sample per 10 km/sup 2/. Water samples were collected from wells, streams, springs, and artificial ponds. Sediment samples were collected from streams, springs, natural ponds, and artificial ponds. Arbitrary anomaly thresholds of two standard deviations above the mean were chosen for both water and sediment sample populations. The U concentrations in waters collected in the Tularosa quadrangle range from below the detection limit of 0.2 parts per billion (ppB) to 57.8 ppB. Most clusters ofmore » water samples containing anomalously high uranium concentrations were collected from locations in uplifts underlain either by volcanic rocks of the mid-Tertiary Datil group or by sedimentary rocks of late Paleozoic and Mesozoic age. Other groups of anomalous waters are from wells that tap Cenozoic aquifers in the intermontane basins. In those areas where the water-sample location coverage is adequate, the known U occurrences are generally associated with high or anomalous U concentrations in water samples. With the exception of one sample with a U concentration of 67.7 ppM, sediments collected in this study have U concentrations that range between 0.2 and 15.2 ppM. Most sediments with U concentrations above the arbitrary anomaly threshold value are from locations which occur in or parallel outcrops of Precambrian crystalline rock exposed in the San Andres and Oscura Mountains. Other anomalous sediments occur as more discreet groups in areas underlain by mid-Tertiary volcanic rocks of the Datil group. Several anomalous samples from the Mogollon-Datil volcanic field were collected along ring fracture systems that surround large volcanic cauldrons.« less

Evaluation of rayon swab surface sample collection method for Bacillus spores from nonporous surfaces.

PubMed

Brown, G S; Betty, R G; Brockmann, J E; Lucero, D A; Souza, C A; Walsh, K S; Boucher, R M; Tezak, M S; Wilson, M C; Rudolph, T; Lindquist, H D A; Martinez, K F

2007-10-01

To evaluate US Centers for Disease Control and Prevention recommended swab surface sample collection method for recovery efficiency and limit of detection for powdered Bacillus spores from nonporous surfaces. Stainless steel and painted wallboard surface coupons were seeded with dry aerosolized Bacillus atrophaeus spores and surface concentrations determined. The observed mean rayon swab recovery efficiency from stainless steel was 0.41 with a standard deviation (SD) of +/-0.17 and for painted wallboard was 0.41 with an SD of +/-0.23. Evaluation of a sonication extraction method for the rayon swabs produced a mean extraction efficiency of 0.76 with an SD of +/-0.12. Swab recovery quantitative limits of detection were estimated at 25 colony forming units (CFU) per sample area for both stainless steel and painted wallboard. The swab sample collection method may be appropriate for small area sampling (10 -25 cm2) with a high agent concentration, but has limited value for large surface areas with a low agent concentration. The results of this study provide information necessary for the interpretation of swab environmental sample collection data, that is, positive swab samples are indicative of high surface concentrations and may imply a potential for exposure, whereas negative swab samples do not assure that organisms are absent from the surfaces sampled and may not assure the absence of the potential for exposure. It is critical from a public health perspective that the information obtained is accurate and reproducible. The consequence of an inappropriate public health response founded on information gathered using an ineffective or unreliable sample collection method has the potential for undesired social and economic impact.

Prediction of Ba, Mn and Zn for tropical soils using iron oxides and magnetic susceptibility

NASA Astrophysics Data System (ADS)

Marques Júnior, José; Arantes Camargo, Livia; Reynaldo Ferracciú Alleoni, Luís; Tadeu Pereira, Gener; De Bortoli Teixeira, Daniel; Santos Rabelo de Souza Bahia, Angelica

2017-04-01

Agricultural activity is an important source of potentially toxic elements (PTEs) in soil worldwide but particularly in heavily farmed areas. Spatial distribution characterization of PTE contents in farming areas is crucial to assess further environmental impacts caused by soil contamination. Designing prediction models become quite useful to characterize the spatial variability of continuous variables, as it allows prediction of soil attributes that might be difficult to attain in a large number of samples through conventional methods. This study aimed to evaluate, in three geomorphic surfaces of Oxisols, the capacity for predicting PTEs (Ba, Mn, Zn) and their spatial variability using iron oxides and magnetic susceptibility (MS). Soil samples were collected from three geomorphic surfaces and analyzed for chemical, physical, mineralogical properties, as well as magnetic susceptibility (MS). PTE prediction models were calibrated by multiple linear regression (MLR). MLR calibration accuracy was evaluated using the coefficient of determination (R2). PTE spatial distribution maps were built using the values calculated by the calibrated models that reached the best accuracy by means of geostatistics. The high correlations between the attributes clay, MS, hematite (Hm), iron oxides extracted by sodium dithionite-citrate-bicarbonate (Fed), and iron oxides extracted using acid ammonium oxalate (Feo) with the elements Ba, Mn, and Zn enabled them to be selected as predictors for PTEs. Stepwise multiple linear regression showed that MS and Fed were the best PTE predictors individually, as they promoted no significant increase in R2 when two or more attributes were considered together. The MS-calibrated models for Ba, Mn, and Zn prediction exhibited R2 values of 0.88, 0.66, and 0.55, respectively. These are promising results since MS is a fast, cheap, and non-destructive tool, allowing the prediction of a large number of samples, which in turn enables detailed mapping of large areas. MS predicted values enabled the characterization and the understanding of spatial variability of the studied PTEs.

Large-scale assessment of benthic communities across multiple marine protected areas using an autonomous underwater vehicle.

PubMed

Ferrari, Renata; Marzinelli, Ezequiel M; Ayroza, Camila Rezende; Jordan, Alan; Figueira, Will F; Byrne, Maria; Malcolm, Hamish A; Williams, Stefan B; Steinberg, Peter D

2018-01-01

Marine protected areas (MPAs) are designed to reduce threats to biodiversity and ecosystem functioning from anthropogenic activities. Assessment of MPAs effectiveness requires synchronous sampling of protected and non-protected areas at multiple spatial and temporal scales. We used an autonomous underwater vehicle to map benthic communities in replicate 'no-take' and 'general-use' (fishing allowed) zones within three MPAs along 7o of latitude. We recorded 92 taxa and 38 morpho-groups across three large MPAs. We found that important habitat-forming biota (e.g. massive sponges) were more prevalent and abundant in no-take zones, while short ephemeral algae were more abundant in general-use zones, suggesting potential short-term effects of zoning (5-10 years). Yet, short-term effects of zoning were not detected at the community level (community structure or composition), while community structure varied significantly among MPAs. We conclude that by allowing rapid, simultaneous assessments at multiple spatial scales, autonomous underwater vehicles are useful to document changes in marine communities and identify adequate scales to manage them. This study advanced knowledge of marine benthic communities and their conservation in three ways. First, we quantified benthic biodiversity and abundance, generating the first baseline of these benthic communities against which the effectiveness of three large MPAs can be assessed. Second, we identified the taxonomic resolution necessary to assess both short and long-term effects of MPAs, concluding that coarse taxonomic resolution is sufficient given that analyses of community structure at different taxonomic levels were generally consistent. Yet, observed differences were taxa-specific and may have not been evident using our broader taxonomic classifications, a classification of mid to high taxonomic resolution may be necessary to determine zoning effects on key taxa. Third, we provide an example of statistical analyses and sampling design that once temporal sampling is incorporated will be useful to detect changes of marine benthic communities across multiple spatial and temporal scales.

Large-scale assessment of benthic communities across multiple marine protected areas using an autonomous underwater vehicle

PubMed Central

Ayroza, Camila Rezende; Jordan, Alan; Figueira, Will F.; Byrne, Maria; Malcolm, Hamish A.; Williams, Stefan B.; Steinberg, Peter D.

2018-01-01

Marine protected areas (MPAs) are designed to reduce threats to biodiversity and ecosystem functioning from anthropogenic activities. Assessment of MPAs effectiveness requires synchronous sampling of protected and non-protected areas at multiple spatial and temporal scales. We used an autonomous underwater vehicle to map benthic communities in replicate ‘no-take’ and ‘general-use’ (fishing allowed) zones within three MPAs along 7o of latitude. We recorded 92 taxa and 38 morpho-groups across three large MPAs. We found that important habitat-forming biota (e.g. massive sponges) were more prevalent and abundant in no-take zones, while short ephemeral algae were more abundant in general-use zones, suggesting potential short-term effects of zoning (5–10 years). Yet, short-term effects of zoning were not detected at the community level (community structure or composition), while community structure varied significantly among MPAs. We conclude that by allowing rapid, simultaneous assessments at multiple spatial scales, autonomous underwater vehicles are useful to document changes in marine communities and identify adequate scales to manage them. This study advanced knowledge of marine benthic communities and their conservation in three ways. First, we quantified benthic biodiversity and abundance, generating the first baseline of these benthic communities against which the effectiveness of three large MPAs can be assessed. Second, we identified the taxonomic resolution necessary to assess both short and long-term effects of MPAs, concluding that coarse taxonomic resolution is sufficient given that analyses of community structure at different taxonomic levels were generally consistent. Yet, observed differences were taxa-specific and may have not been evident using our broader taxonomic classifications, a classification of mid to high taxonomic resolution may be necessary to determine zoning effects on key taxa. Third, we provide an example of statistical analyses and sampling design that once temporal sampling is incorporated will be useful to detect changes of marine benthic communities across multiple spatial and temporal scales. PMID:29547656

Integration of biomonitoring and instrumental techniques to assess the air quality in an industrial area located in the coastal of central Asturias, Spain.

PubMed

Almeida, Susana Marta; Lage, Joana; Freitas, Maria do Carmo; Pedro, Ana Isabel; Ribeiro, Tiago; Silva, Alexandra Viana; Canha, Nuno; Almeida-Silva, Marina; Sitoe, Timóteo; Dionisio, Isabel; Garcia, Sílvia; Domingues, Gonçalo; de Faria, Julia Perim; Fernández, Beatriz González; Ciaparra, Diane; Wolterbeek, Hubert T

2012-01-01

Throughout the world, epidemiological studies were established to examine the relationship between air pollution and mortality rates and adverse respiratory health effects. However, despite the years of discussion the correlation between adverse health effects and atmospheric pollution remains controversial, partly because these studies are frequently restricted to small and well-monitored areas. Monitoring air pollution is complex due to the large spatial and temporal variations of pollution phenomena, the high costs of recording instruments, and the low sampling density of a purely instrumental approach. Therefore, together with the traditional instrumental monitoring, bioindication techniques allow for the mapping of pollution effects over wide areas with a high sampling density. In this study, instrumental and biomonitoring techniques were integrated to support an epidemiological study that will be developed in an industrial area located in Gijon in the coastal of central Asturias, Spain. Three main objectives were proposed to (i) analyze temporal patterns of PM₁₀ concentrations in order to apportion emissions sources, (ii) investigate spatial patterns of lichen conductivity to identify the impact of the studied industrial area in air quality, and (iii) establish relationships amongst lichen conductivity with some site-specific characteristics. Samples of the epiphytic lichen Parmelia sulcata were transplanted in a grid of 18 by 20 km with an industrial area in the center. Lichens were exposed for a 5-mo period starting in April 2010. After exposure, lichen samples were soaked in 18-MΩ water aimed at determination of water electrical conductivity and, consequently, lichen vitality and cell damage. A marked decreasing gradient of lichens conductivity relative to distance from the emitting sources was observed. Transplants from a sampling site proximal to the industrial area reached values 10-fold higher than levels far from it. This finding showed that lichens reacted physiologically in the polluted industrial area as evidenced by increased conductivity correlated to contamination level. The integration of temporal PM₁₀ measurements and analysis of wind direction corroborated the importance of this industrialized region for air quality measurements and identified the relevance of traffic for the urban area.

Evidence of Lake Trout reproduction at Lake Michigan's mid-lake reef complex

USGS Publications Warehouse

Janssen, J.; Jude, D.J.; Edsall, T.A.; Paddock, R.W.; Wattrus, N.; Toneys, M.; McKee, P.

2006-01-01

The Mid-Lake Reef Complex (MLRC), a large area of deep (> 40 m) reefs, was a major site where indigenous lake trout (Salvelinus namaycush) in Lake Michigan aggregated during spawning. As part of an effort to restore Lake Michigan's lake trout, which were extirpated in the 1950s, yearling lake trout have been released over the MLRC since the mid-1980s and fall gill net censuses began to show large numbers of lake trout in spawning condition beginning about 1999. We report the first evidence of viable egg deposition and successful lake trout fry production at these deep reefs. Because the area's existing bathymetry and habitat were too poorly known for a priori selection of sampling sites, we used hydroacoustics to locate concentrations of large fish in the fall; fish were congregating around slopes and ridges. Subsequent observations via unmanned submersible confirmed the large fish to be lake trout. Our technological objectives were driven by biological objectives of locating where lake trout spawn, where lake trout fry were produced, and what fishes ate lake trout eggs and fry. The unmanned submersibles were equipped with a suction sampler and electroshocker to sample eggs deposited on the reef, draw out and occasionally catch emergent fry, and collect egg predators (slimy sculpin Cottus cognatus). We observed slimy sculpin to eat unusually high numbers of lake trout eggs. Our qualitative approaches are a first step toward quantitative assessments of the importance of lake trout spawning on the MLRC.

Habitat fragmentation effects on birds in grasslands and wetlands: A critique of our knowledge

USGS Publications Warehouse

Johnson, D.H.

2001-01-01

Habitat fragmentation exacerbates the problem of habitat loss for grassland and wetland birds. Remaining patches of grasslands and wetlands may be too small, too isolated, and too influenced by edge effects to maintain viable populations of some breeding birds. Knowledge of the effects of fragmentation on bird populations is critically important for decisions about reserve design, grassland and wetland management, and implementation of cropland set-aside programs that benefit wildlife. In my review of research that has been conducted on habitat fragmentation, I found at least five common problems in the methodology used. The results of many studies are compromised by these problems: passive sampling (sampling larger areas in larger patches), confounding effects of habitat heterogeneity, consequences of inappropriate pooling of data from different species, artifacts associated with artificial nest data, and definition of actual habitat patches. As expected, some large-bodied birds with large territorial requirements, such as the northern harrier (Circus cyaneus), appear area sensitive. In addition, some small species of grassland birds favor patches of habitat far in excess of their territory size, including the Savannah (Passerculus sandwichensis), grasshopper (Ammodramus savannarum) and Henslow's (A. henslowii) sparrows, and the bobolink (Dolichonyx oryzivorus). Other species may be area sensitive as well, but the data are ambiguous. Area sensitivity among wetland birds remains unknown since virtually no studies have been based on solid methodologies. We need further research on grassland bird response to habitat that distinguishes supportable conclusions from those that may be artifactual.

Nutrients in ground water and surface water of the United States; an analysis of data through 1992

USGS Publications Warehouse

Mueller, D.K.; Hamilton, P.A.; Helsel, D.R.; Hitt, K.J.; Ruddy, B.C.

1995-01-01

Historical data on nutrient (nitrogen and phosphorus species) concentrations in ground-and surface-water samples were compiled from 20 study units of the National Water-Quality Assessment (NAWQA) Program and 5 supplemental study areas. The resultant national retrospective data sets contained analyses of about 12,000 Found-water and more than 22,000 surface-water samples. These data were interpreted on regional and national scales by relating the distributions of nutrient concentrations to ancillary data, such as land use, soil characteristics, and hydrogeology, provided by local study-unit personnel. The information provided in this report on environmental factors that affect nutrient concentrations in ground and surface water can be used to identify areas of the Nation where the vulnerability to nutrient contamination is greatest. Nitrate was the nutrient of greatest concern in the historical ground-water data. It is the only nutrient that is regulated by a national drinking-water standard. Nitrate concentrations were significantly different in ground water affected by various land uses. Concentrations in about 16 percent of the samples collected in agricultural areas exceeded the drinking-water standard. However, the standard was exceeded in only about 1 percent of samples collected from public-supply wells. A variety of ancillary factors had significant relations to nitrate concentrations in ground water beneath agricultural areas. Concentrations generally were highest within 100 feet of the land surface. They were also higher in areas where soil and geologic characteristics promoted rapid movement of water to the aquifer. Elevated concentrations commonly occurred in areas underlain by permeable materials, such as carbonate bedrock or unconsolidated sand and gravel, and where soils are generally well drained. In areas where water movement is impeded, denitrification might lead to low concentrations of nitrate in the ground water. Low concentrations were also related to interspersion of pasture and woodland with cropland in agricultural areas. Elevated nitrate concentrations in areas of more homogeneous cropland probably were a result of intensive nitrogen fertilizer application on large tracts of land. Certain regions of the United States seemed more vulnerable to nitrate contamination of ground water in agricultural areas. Regions of greater vulnerability included parts of the Northeast, Midwest, and West Coast. The well-drained soils, typical in these regions, have little capacity to hold water and nutrients; therefore, these soils receive some of the largest applications of fertilizer and irrigation in the Nation. The agricultural land is intensively cultivated for row crops, with little interspersion of pasture and woodland. Nutrient concentrations in surface water also were generally related to land use. Nitrate concentrations were highest in samples from sites downstream from agricultural or urban areas. However, concentrations were not as high as in ground water and rarely exceeded the drinking-water standard. Elevated concentrations of nitrate in surface water of the Northeastern United States might be related to large amounts of atmospheric deposition (acid rain). High concentrations in parts of the Midwest might be related to tile drainage of agricultural fields. Ammonia and phosphorus concentrations were highest downstream from urban areas. These concentrations generally were high enough to warrant concerns about toxicity to fish and accelerated eutrophication. Recent improvements in wastewater treatment have decreased ammonia concentrations downstream from some urban areas, but the result has been an increase in nitrate concentrations. Information on environmental factors that affect water quality is useful to identify drainage basins throughout the Nation with the greatest vulnerability for nutrient contamination and to delineate areas where ground-water or surface-water contamination is most likely to oc

A geostatistical approach for quantification of contaminant mass discharge uncertainty using multilevel sampler measurements

NASA Astrophysics Data System (ADS)

Li, K. Betty; Goovaerts, Pierre; Abriola, Linda M.

2007-06-01

Contaminant mass discharge across a control plane downstream of a dense nonaqueous phase liquid (DNAPL) source zone has great potential to serve as a metric for the assessment of the effectiveness of source zone treatment technologies and for the development of risk-based source-plume remediation strategies. However, too often the uncertainty of mass discharge estimated in the field is not accounted for in the analysis. In this paper, a geostatistical approach is proposed to estimate mass discharge and to quantify its associated uncertainty using multilevel transect measurements of contaminant concentration (C) and hydraulic conductivity (K). The approach adapts the p-field simulation algorithm to propagate and upscale the uncertainty of mass discharge from the local uncertainty models of C and K. Application of this methodology to numerically simulated transects shows that, with a regular sampling pattern, geostatistics can provide an accurate model of uncertainty for the transects that are associated with low levels of source mass removal (i.e., transects that have a large percentage of contaminated area). For high levels of mass removal (i.e., transects with a few hot spots and large areas of near-zero concentration), a total sampling area equivalent to 6˜7% of the transect is required to achieve accurate uncertainty modeling. A comparison of the results for different measurement supports indicates that samples taken with longer screen lengths may lead to less accurate models of mass discharge uncertainty. The quantification of mass discharge uncertainty, in the form of a probability distribution, will facilitate risk assessment associated with various remediation strategies.

Health risks of heavy metal exposure through vegetable consumption near a large-scale Pb/Zn smelter in central China.

PubMed

Li, Xinyu; Li, Zhonggen; Lin, Che-Jen; Bi, Xiangyang; Liu, Jinling; Feng, Xinbin; Zhang, Hua; Chen, Ji; Wu, Tingting

2018-06-04

Smelting of nonferrous metals is an important source of heavy metals in surface soil. The crops/vegetables grown on contaminated soil potentially impose adverse effects on human health. In this study, the contamination level of five heavy metals (Hg, Pb, Zn, Cd and Cu) in ten types of vegetables grown nearby a large scale Pb/Zn smelter in Hunan Province, China and the health risk associated with their consumption are assessed. Based on the data obtained from 52 samples, we find that Pb and Cd contributed to the greatest health risk and leafy vegetables tend to be more contaminated than non-leafy vegetables. Within 4 km radius of the smelter, over 75% of vegetable samples exceeded the national food standard for Pb; over 47% exceeded the Cd standard; and 7% exceeded the Hg standard. Heavy metal concentrations in vegetables measured within the 4 km radius are on average three times more elevated compared to those found at the control area 15 km away. Heavy metals in vegetables have dual sources of root absorption from soil and leaf adsorption from atmosphere. Health risk in terms of the hazard index (HI) at contaminated areas are 3.66 and 3.14 for adults and children, respectively, suggesting adverse health effects would occur. HI for both groups are mainly contributed by Pb (48%) and Cd (40%). Fortunately, vegetable samples collected at the control area are considered safe to consume. Copyright © 2018 Elsevier Inc. All rights reserved.

A sampling design framework for monitoring secretive marshbirds

USGS Publications Warehouse

Johnson, D.H.; Gibbs, J.P.; Herzog, M.; Lor, S.; Niemuth, N.D.; Ribic, C.A.; Seamans, M.; Shaffer, T.L.; Shriver, W.G.; Stehman, S.V.; Thompson, W.L.

2009-01-01

A framework for a sampling plan for monitoring marshbird populations in the contiguous 48 states is proposed here. The sampling universe is the breeding habitat (i.e. wetlands) potentially used by marshbirds. Selection protocols would be implemented within each of large geographical strata, such as Bird Conservation Regions. Site selection will be done using a two-stage cluster sample. Primary sampling units (PSUs) would be land areas, such as legal townships, and would be selected by a procedure such as systematic sampling. Secondary sampling units (SSUs) will be wetlands or portions of wetlands in the PSUs. SSUs will be selected by a randomized spatially balanced procedure. For analysis, the use of a variety of methods as a means of increasing confidence in conclusions that may be reached is encouraged. Additional effort will be required to work out details and implement the plan.

Composition and structure of macrozooplankton and micronekton communities in the vicinity of free-drifting Antarctic icebergs

NASA Astrophysics Data System (ADS)

Kaufmann, Ronald S.; Robison, Bruce H.; Sherlock, Rob E.; Reisenbichler, Kim R.; Osborn, Karen J.

2011-06-01

Recent warming in the Antarctic has led to increased production of icebergs; however, the ecological effects of icebergs on pelagic communities within the Southern Ocean have not been well-studied. We used a 10 m 2 MOCNESS to collect macrozooplankton and micronekton in the upper 300 m of the water column near free-drifting icebergs in the Atlantic sector of the Southern Ocean during three seasons: December 2005 (late spring), June 2008 (late fall) and March-April 2009 (late summer). Communities were dominated in all three seasons by Antarctic krill ( Euphausia superba) and salps ( Salpa thompsoni), which collectively comprised 60-95% of the community wet biomass in most cases. During our spring and summer cruises, mean biomass was elevated by 3.1-4.3x at a distance of 0.37 km from large icebergs vs. 9.26 km away. These differences were not statistically significant, and no trend in biomass with distance was apparent in samples from fall 2008, when total biomass was an order of magnitude lower. Biomass levels near icebergs during Dec 2005 and Mar-Apr 2009 were comparable to values reported from marginal ice zones, suggesting that waters around icebergs support macrozooplankton and micronekton communities comparable in magnitude to those in some of the most productive areas of the Southern Ocean. Sample variance also was significantly higher within 1.85 km of icebergs during Dec 2005 and Mar-Apr 2009, reflecting increased patchiness on scales sampled by the MOCNESS (20-40×10 3 m 3 filtered per sample). This pattern was not significant during Jun 2008. Large predatory medusae were observed within 1.85 km of icebergs and in Iceberg Alley, an area through which icebergs pass frequently, but were virtually absent in areas remote from icebergs. Small euphausiids showed an inverse distribution, with low densities in areas populated by large medusae. A shift in community composition from a near-iceberg assemblage dominated by herbivores to a carnivore-dominated community in Iceberg Alley may reflect a transition from bottom-up to top-down control with increasing distance and time. Body sizes of dominant species varied seasonally but did not show consistent trends with distance from icebergs. Concentrations of photosynthetic pigments in the guts of E. superba and S. thompsoni corresponded broadly to patterns in surface chlorophyll a concentrations and were comparable to maximum gut pigment concentrations measured in animals collected from highly productive marginal ice zones. Our results suggest that the macrozooplankton and micronekton assemblages near free-drifting icebergs can be quantitatively and qualitatively different from those in surrounding, iceberg-free waters, perhaps due to both bottom-up and top-down processes as well as physical forcing by the passage of a large object through the upper ocean.

White Dwarfs in the SDSS Photometric Footprint

NASA Astrophysics Data System (ADS)

Gentile Fusillo, N. P.; Girven, J.; Gänsicke, B.

2013-01-01

Attempts to create a homogeneous catalogue of white dwarfs have always been faced with the challenge posed by the intrinsic faintness of these objects. In recent years, thanks to large area surveys like the Sloan Digital Sky Survey (SDSS), the size of the known white dwarf population has increased dramatically, but, in order to carry out a statical study on the population of white dwarfs, it is necessary to have a reliable and well-defined selection method. We present a method which uses cuts in colour-colour space to select from DR7 16785 bright (g ≤ 19) photometric DA white dwarf candidates (Girven et al. 2011). The selection is 62% efficient in returning DA white dwarfs and produces a DA sample which is 95% complete for Teff > 8000 K. This sample contains 4636 spectroscopically confirmed DA white dwarfs; i.e. a ˜70% increase compared to Eisenstein et al.'s sample. As a first application of the SDSS DR7 DA candidates sample we cross correlated it with Data Release 8 of UKIDSS Large Area Survey with the aim of identifying white dwarfs which exhibit an infrared excess consistent with the presence of low mass stellar companions or dusty debris discs. Our current work aims to extend the photometric selection to all types of white dwarfs, using reduced proper motion as a further constrain. We expect to find a total of ˜20 000 photometric white dwarf candidates with g ≤ 19 in the footprint of SDSS DR8.

Impact of spatial variability and sampling design on model performance

NASA Astrophysics Data System (ADS)

Schrape, Charlotte; Schneider, Anne-Kathrin; Schröder, Boris; van Schaik, Loes

2017-04-01

Many environmental physical and chemical parameters as well as species distributions display a spatial variability at different scales. In case measurements are very costly in labour time or money a choice has to be made between a high sampling resolution at small scales and a low spatial cover of the study area or a lower sampling resolution at the small scales resulting in local data uncertainties with a better spatial cover of the whole area. This dilemma is often faced in the design of field sampling campaigns for large scale studies. When the gathered field data are subsequently used for modelling purposes the choice of sampling design and resulting data quality influence the model performance criteria. We studied this influence with a virtual model study based on a large dataset of field information on spatial variation of earthworms at different scales. Therefore we built a virtual map of anecic earthworm distributions over the Weiherbach catchment (Baden-Württemberg in Germany). First of all the field scale abundance of earthworms was estimated using a catchment scale model based on 65 field measurements. Subsequently the high small scale variability was added using semi-variograms, based on five fields with a total of 430 measurements divided in a spatially nested sampling design over these fields, to estimate the nugget, range and standard deviation of measurements within the fields. With the produced maps, we performed virtual samplings of one up to 50 random points per field. We then used these data to rebuild the catchment scale models of anecic earthworm abundance with the same model parameters as in the work by Palm et al. (2013). The results of the models show clearly that a large part of the non-explained deviance of the models is due to the very high small scale variability in earthworm abundance: the models based on single virtual sampling points on average obtain an explained deviance of 0.20 and a correlation coefficient of 0.64. With increasing sampling points per field, we averaged the measured abundance of the sampling within each field to obtain a more representative value of the field average. Doubling the samplings per field strongly improved the model performance criteria (explained deviance 0.38 and correlation coefficient 0.73). With 50 sampling points per field the performance criteria were 0.91 and 0.97 respectively for explained deviance and correlation coefficient. The relationship between number of samplings and performance criteria can be described with a saturation curve. Beyond five samples per field the model improvement becomes rather small. With this contribution we wish to discuss the impact of data variability at sampling scale on model performance and the implications for sampling design and assessment of model results as well as ecological inferences.

The Large Area KX Quasar Survey: Photometric Redshift Selection and the Complete Quasar Catalogue

NASA Astrophysics Data System (ADS)

Maddox, Natasha; Hewett, P. C.; Peroux, C.

2013-01-01

We have completed a large area, ˜600 square degree, spectroscopic survey for luminous quasars flux-limited in the K-band. The survey utilises the UKIRT Infrared Deep Sky Survey (UKIDSS) Large Area Survey (LAS) in regions of sky within the Sloan Digital Sky Survey (SDSS) footprint. We exploit the K-band excess (KX) of all quasars with respect to Galactic stars in combination with a custom-built photometric redshift/classification scheme to identify quasar candidates for spectroscopic follow-up observations. The survey is complete to K≤16.6, and includes >3200 known quasars from the SDSS, with more than 250 additional confirmed quasars from the KX-selection which eluded the SDSS quasar selection algorithm. The selection is >95% complete with respect to known SDSS quasars and >95% efficient, largely independent of redshift and magnitude. The KX-selected quasars will provide new constraints on the fraction of luminous quasars reddened by dust with E(B-V)≤0.5 mag. Several projects utilizing the KX quasars are ongoing, including a spectroscopic campaign searching for dusty quasar intervening absorption systems. The KX survey is a well-defined sample of quasars useful for investigating the properties of luminous quasars with intermediate levels of dust extinction either within their host galaxies or due to intervening absorption systems.

Characterization and provenance of the building stones from Pompeii's archaeological site (southern Italy)

NASA Astrophysics Data System (ADS)

Balassone, G.; Kastenmeier, P.; di Maio, G.; Mormone, A.; Joachimski, M.

2009-04-01

Pompeii is one of the most famous and complex areas of archaeological investigation in the world and with a uniquely favorable state of preservation. Even if many studies have been devoted in time to many archaeological aspects of this ancient city, large-scale and detailed studies aimed at characterizing mineralogy, petrography and isotope geochemistry of the building stones are still lacking. The scope of the present research is to fill this gap, pointing to the definition of the provenance of the stony materials used for ancient constructions of the city of Pompeii and to the possible trade routes. This work is part of a large-scale survey carried out by the Deutsches Archäologisches Institut of Berlin, with the purposes of reconstructing the sources of raw materials of various archaeological sites of the Sarno Plain (e.g. Longola-Poggiomarino settlement, Nuceria, Stabiae, etc.) and consequently also the paleo-environments of this area during the Olocene (Seiler, 2006, 2008; Kastemeier and Seiler, 2007). We sampled all the litotypes with different macroscopic characteristics from various buildings according to location, age (time span VI century B.C. - I century A.D.) and utilization; the architectural buildings considered for this study are mainly represented public and religious buildings, houses and funerary monuments. As possible source areas, representative litotypes have been sampled from ancient pits and outcrops surrounding Pompeii as well. A set of 80 samples have been sampled by means of micro-drillings for mineralogical, petrographic and geochemical analyses, comprising optical microscopy, X-ray diffraction, inductively coupled plasma mass, X-ray fluorescence and C-O isotope geochemistry. Minero-petrographic and XRD studies of Pompeii rock samples have shown that at least ten different litologies occur as building stones, belonging to basaltic to tephritic lavas, pyroclasts (tuffs, scoriae, etc.) and sedimentary rocks (limestone, travertines). Preliminary results on source localities indicate a local provenance for a set of volcanic rock samples, whereas the possible source areas of the sedimentary litotypes seem to be more complex. New minero-petrographic data of samples from surrounding outcrops are presented and compared to the related Pompeii building stones. References Seiler F. (2006) - Current research projects. In: Aktuelle Forchungsprojeckte, Deutsches Archäologisches Institut Zentrale, 34-35. Seiler F. (2008) - Rekonstruktion der antiken Kulturlandschaften des Sarno-Beckens. Ein multidisziplinäres Kooperationsprojekt mit Partnern aus Naturwissenschaften und Altertumswissenschaften in Deutschland, Italien und England. In: P. G. Guzzo - M. P. Guidobaldi (Eds), Nuove ricerche archeologiche nell'area vesuviana (scavi 2003-2006). Convegno Internazionale, Roma 1-3 febbraio, 485-490. Kastenmeier P., Seiler F. (2007) - La ricostruzione dei paleo-paesaggi nella piana del Sarno. Quaderni Autorità di Bacino del Sarno. Studi, documentazione e ricerca, 1, 24-26.

Indicators of the statuses of amphibian populations and their potential for exposure to atrazine in four midwestern U.S. conservation areas

USGS Publications Warehouse

Sadinski, Walter; Roth, Mark; Hayes, Tyrone; Jones, Perry; Gallant, Alisa

2014-01-01

Extensive corn production in the midwestern United States has physically eliminated or fragmented vast areas of historical amphibian habitat. Midwestern corn farmers also apply large quantities of fertilizers and herbicides, which can cause direct and indirect effects on amphibians. Limited field research regarding the statuses of midwestern amphibian populations near areas of corn production has left resource managers, conservation planners, and other stakeholders needing more information to improve conservation strategies and management plans. We repeatedly sampled amphibians in wetlands in four conservation areas along a gradient of proximity to corn production in Illinois, Iowa, Minnesota, and Wisconsin from 2002 to 2005 and estimated site occupancy. We measured frequencies of gross physical deformities in recent metamorphs and triazine concentrations in the water at breeding sites. We also measured trematode infection rates in kidneys of recently metamorphosed Lithobates pipiens collected from nine wetlands in 2003 and 2004. We detected all possible amphibian species in each study area. The amount of nearby row crops was limited in importance as a covariate for estimating site occupancy. We observed deformities in <5% of metamorphs sampled and proportions were not associated with triazine concentrations. Trematode infections were high in metamorphs from all sites we sampled, but not associated with site triazine concentrations, except perhaps for a subset of sites sampled in both years. We detected triazines more often and in higher concentrations in breeding wetlands closer to corn production. Triazine concentrations increased in floodplain wetlands as water levels rose after rainfall and were similar among lotic and lentic sites. Overall, our results suggest amphibian populations were not faring differently among these four conservation areas, regardless of their proximity to corn production, and that the ecological dynamics of atrazine exposure were complex.

Indicators of the Statuses of Amphibian Populations and Their Potential for Exposure to Atrazine in Four Midwestern U.S. Conservation Areas

PubMed Central

Sadinski, Walt; Roth, Mark; Hayes, Tyrone; Jones, Perry; Gallant, Alisa

2014-01-01

Extensive corn production in the midwestern United States has physically eliminated or fragmented vast areas of historical amphibian habitat. Midwestern corn farmers also apply large quantities of fertilizers and herbicides, which can cause direct and indirect effects on amphibians. Limited field research regarding the statuses of midwestern amphibian populations near areas of corn production has left resource managers, conservation planners, and other stakeholders needing more information to improve conservation strategies and management plans. We repeatedly sampled amphibians in wetlands in four conservation areas along a gradient of proximity to corn production in Illinois, Iowa, Minnesota, and Wisconsin from 2002 to 2005 and estimated site occupancy. We measured frequencies of gross physical deformities in recent metamorphs and triazine concentrations in the water at breeding sites. We also measured trematode infection rates in kidneys of recently metamorphosed Lithobates pipiens collected from nine wetlands in 2003 and 2004. We detected all possible amphibian species in each study area. The amount of nearby row crops was limited in importance as a covariate for estimating site occupancy. We observed deformities in <5% of metamorphs sampled and proportions were not associated with triazine concentrations. Trematode infections were high in metamorphs from all sites we sampled, but not associated with site triazine concentrations, except perhaps for a subset of sites sampled in both years. We detected triazines more often and in higher concentrations in breeding wetlands closer to corn production. Triazine concentrations increased in floodplain wetlands as water levels rose after rainfall and were similar among lotic and lentic sites. Overall, our results suggest amphibian populations were not faring differently among these four conservation areas, regardless of their proximity to corn production, and that the ecological dynamics of atrazine exposure were complex. PMID:25216249

Tracing organic and inorganic pollution sources of soils and water resources in Güzelhisar Basin of Aegean Region, Turkey

NASA Astrophysics Data System (ADS)

Czarnecki, Sezin; Colak Esetlili, Bihter; Esetlili, Tolga; Tepecik, Mahmut; Kurucu, Yusuf; Anac, Dilek; Düring, Rolf-Alexander

2017-04-01

This study was carried out to determine the residue level of major concern organic and inorganic pollutants in Güzelhisar Basin of Aegean Region in Turkey which represents a rather industrialized area having five large iron and steel mills, but also areas of agriculture. Soil samples were collected from GPS determined points at 0-30 and 30-60 cm depth of a grid system of 2.5 km to the east and 2.5 km to the west of the Güzelhisar stream. The area was grouped into three main areas as West, Middle, and East region. Water and sediment samples were collected from the Güzelhisar stream and from Güzelhisar dam every 30 kilometers which is already contaminated due to industrial facilities in Aliaga, is used to irrigate the agricultural land. Soil pH of the research area was determined within the range from 5.87 to 6.61. Topsoil contamination was examined for all investigated elements with the exception of Cd. An increase in pseudo total metal contents of Cr, Cu, Mn, Ni, and Zn was observed with increasing distance from the coast with a simultaneous decrease in pH. Due to the analysis of the organic pollutants, a continuous load with the herbicide trifluralin was determined with a few clearly raised points to a possible load of the stream water. Although HCH-Isomers were not found, DDT (DDT and transformation products) residues were ascertained in the soil samples. With regard to the analysis of the water samples of the Güzelhisar stream and dam, a background load with trifluralin was found which is to be explained with transport processes with regard to utilization of trifluralin in the agricultural areas.

GIS modeling of archaeological site locations: A low-tech approach

NASA Technical Reports Server (NTRS)

Futato, Eugene M.

1991-01-01

A Geographic Information System (GIS)-type analysis of archaeological site locations using a dBase III plus program and a desk top computer is presented. A previously developed model of site locations in the Sequatchie Valley of northeastern Alabama is tested against known site locations in another large survey area there. The model fails to account for site locations in the test area. A model is developed for the test area and indicates the site locations are indeed different. Whether this is due to differences in site locations on a sub-regional level, or to sample error in the original model is unknown.

High Resolution Seamless Dom Generation Over CHANG'E-5 Landing Area Using Lroc Nac Images

NASA Astrophysics Data System (ADS)

Di, K.; Jia, M.; Xin, X.; Liu, B.; Liu, Z.; Peng, M.; Yue, Z.

2018-04-01

Chang'e-5, China's first sample return lunar mission, will be launched in 2019, and the planned landing area is near Mons Rümker in Oceanus Procellarum. High-resolution and high-precision mapping of the landing area is of great importance for supporting scientific analysis and safe landing. This paper proposes a systematic method for large area seamless digital orthophoto map (DOM) generation, and presents the mapping result of Chang'e-5 landing area using over 700 LROC NAC images. The developed method mainly consists of two stages of data processing: stage 1 includes subarea block adjustment with rational function model (RFM) and seamless subarea DOM generation; stage 2 includes whole area adjustment through registration of the subarea DOMs with thin plate spline model and seamless DOM mosaicking. The resultant seamless DOM coves a large area (20° longitude × 4° latitude) and is tied to the widely used reference DEM - SLDEM2015. As a result, the RMS errors of the tie points are all around half pixel in image space, indicating a high internal precision; the RMS errors of the control points are about one grid cell size of SLDEM2015, indicating that the resultant DOM is tied to SLDEM2015 well.

Applications of Cosmogenic He-3 and Ne-21 Dating to Glacial Moraines in Antarctica and California

NASA Astrophysics Data System (ADS)

Sams, S.; Morgan, D. J.; Balco, G.; Putkonen, J.; Bibby, T.

2015-12-01

The depositional age of moraines can be determined through cosmogenic nuclide exposure dating. These ages are useful in establishing a glacial history of an area and ascribing age constraints to transport processes. Be-10 is the most common nuclide used for exposure dating today, but this method is both expensive and time consuming because it requires analysis by accelerator mass spectrometry (AMS). He-3 and Ne-21 can be analyzed using noble gas mass spectrometry, which is more cost efficient than AMS and requires less chemical preparation. We collected samples from areas in Moraine Canyon, Antarctica (86.10° S, 157.75° W), which is a dry valley in the Transantarctic Mountains. Dolerite boulders along a transect of recessional moraines were sampled in the typical fashion of using a large piece of the boulder for analysis. Pyroxene minerals have been separated from these samples following the method of Bromley et al. (2014) using hydrofluoric acid. Exposure ages will be calculated from the He-3 concentrations in them. In the Mono Lake area of California, moraines were sampled from Bloody Canyon and McGee Creek sites. Instead of collecting a sample from an individual boulder, we collected approximately 25 granitic pebbles (1-3 cm) from 4-6 sites along the crest of the moraines following the method of Briner (2009). Each suite of pebbles was crushed together, and quartz minerals were separated from the agglomeration of pebbles. Cosmogenic Ne-21 will be measured from these samples to determine their exposure age. From these two field sites, we will use He-3 and Ne-21 to better understand the timing and extent of glaciation in these areas.

Geological and geochemical studies in the Wadi Bidah District, Kingdom of Saudi Arabia

USGS Publications Warehouse

Smith, C.W.; Waters, B.C.; Naqvi, M.; Worl, R.G.; Helaby, A.M.; Flanigan, V.J.; Sadek, H.S.; Samater, R.M.

1983-01-01

Geological and geochemical followup studies of airborne electromagnetic anomalies in the Wadi Bidah district, southwestern Saudi Arabia, did not reveal metals of economic grade. Investigation of an anomaly enclosing the Rabathan ancient mine disclosed tightly folded and sheared Proterozoic tuffaceous rocks interlayered mostly with chert, dolomite, carbonaceous rocks, and volcanic wacke including cherty iron-manganese formations slightly anomalous in copper and zinc. Three drill holes placed to test anomalies within these formations yielded negative results. Studies of a long, narrow anomaly north of the Rabathan area indicated a similar geological environment. This northern area also contains limited zones that are highly anomalous in copper and zinc and extensive zones that are slightly anomalous in those metals. Drilling was not undertaken in this area. The Bilajimah airborne electromagnetic anomaly west of Wadi Bidah coincides with a broad synclinorium of layered felsic turfs and gossans. Geochemical studies indicated slightly anomalous copper, zinc, and silver values in gossans within the anomaly area. Two drill holes intersected carbonaceous rock that contained approximately 15 percent pyrrhotite and traces of sphalerite and chalcopyrite. Two geophysically anomalous areas west of Wadi Bidah surround ancient mines at Mahawiyah and Khayal al Masna'ah. Results of geochemical sampling at these workings were positive. An airborne electromagnetic anomaly located in the Assifar area in the southwestern corner of the Wadi Bidah district is underlain principally by metasedimentary rocks that include large linear zones of cherty iron-manganese formation and a few gossans .containing secondary base metal minerals. Detailed mapping and sampling of the Mulhal ancient mine, located west of Wadi Bidah, revealed two types of polymetallic gossans : (1) stratiform deposits interlayered with ignimbrites and mafic volcanic rocks and (2) barite-bearing gossanous material in shear zones that grade into hydrothermally altered shear zones and extend beyond the mine area. The gossans and gossanous shear zones contain anomalous amounts of gold, silver, lead, copper, zinc, barium, and selenium. Two gossans west of Wadi Bidah were mapped and sampled in detail; both gossans are interlayered, with siliceous volcanic rocks. Although the gossan at Jabal Mohr covers a large area, it contains low amounts of precious and base metals. The gossan at Mulhal No. 2 contains moderate to high amounts of gold, silver, copper, lead, and zinc.

18/20 T high magnetic field scanning tunneling microscope with fully low voltage operability, high current resolution, and large scale searching ability.

PubMed

Li, Quanfeng; Wang, Qi; Hou, Yubin; Lu, Qingyou

2012-04-01

We present a home-built 18/20 T high magnetic field scanning tunneling microscope (STM) featuring fully low voltage (lower than ±15 V) operability in low temperatures, large scale searching ability, and 20 fA high current resolution (measured by using a 100 GOhm dummy resistor to replace the tip-sample junction) with a bandwidth of 3.03 kHz. To accomplish low voltage operation which is important in achieving high precision, low noise, and low interference with the strong magnetic field, the coarse approach is implemented with an inertial slider driven by the lateral bending of a piezoelectric scanner tube (PST) whose inner electrode is axially split into two for enhanced bending per volt. The PST can also drive the same sliding piece to inertial slide in the other bending direction (along the sample surface) of the PST, which realizes the large area searching ability. The STM head is housed in a three segment tubular chamber, which is detachable near the STM head for the convenience of sample and tip changes. Atomic resolution images of a graphite sample taken under 17.6 T and 18.0001 T are presented to show its performance. © 2012 American Institute of Physics

A novel approach to water polution monitoring by combining ion exchange resin and XRF-scanning technique

NASA Astrophysics Data System (ADS)

Huang, J. J.; Lin, S. C.; Löwemark, L.; Liou, Y. H.; Chang, Q. M.; Chang, T. K.; Wei, K. Y.; Croudace, I. W. C.

2017-12-01

Due to the rapid industrial expansion, environments are subject to irregular fluctuations and spatial distributions in pollutant concentrations. This study proposes to use ion exchange resin accompanied with the XRF-scanning technique to monitor environmental pollution. As a passive sampling sorbent, the use of ion exchange resin provides a rapid, low cost and simple method to detect episodic pollution signals with a high spatial sampling density. In order to digest large quantities of samples, the fast and non-destructive Itrax-XRF core scanner has been introduced to assess elemental concentrations in the resin samples. Although the XRF scanning results are often considered as a semi-quantitative measurement due to possible absorption or scattering caused by the physical variabilities of scanned materials, the use of resin can minimize such influences owing to the standarization of the sample matrix. In this study, 17 lab-prepared standard resin samples were scanned with the Itrax-XRF core scanner (at 100 s exposure time with the Mo-tube) and compared with the absolute elemental concentrations. Six elements generally used in pollution studies (Cr, Mn, Ni, Cu, Zn, and Pb) were selected, and their regression lines and correlation coefficients were determined. In addition, 5 standard resin samples were scanned at different exposure time settings (1 s, 5 s, 15 s, 30 s, 100 s) to address the influence of exposure time on the accuracy of the measurements. The results show that within the test range (from few ppm to thousands ppm), the correlation coefficients are higher than 0.97, even at the shortest exposure time (1 s). Furthermore, a pilot field survey with 30 resin samples has been conducted in a potentially polluted farm area in central Taiwan to demonstrate the feasibility of this novel approach. The polluted hot zones could be identified and the properties and sources of wastewater pollution can therefore be traced over large areas for the purposes of environmental monitoring and environmental forensics.

Using LUCAS topsoil database to estimate soil organic carbon content in local spectral libraries

NASA Astrophysics Data System (ADS)

Castaldi, Fabio; van Wesemael, Bas; Chabrillat, Sabine; Chartin, Caroline

2017-04-01

The quantification of the soil organic carbon (SOC) content over large areas is mandatory to obtain accurate soil characterization and classification, which can improve site specific management at local or regional scale exploiting the strong relationship between SOC and crop growth. The estimation of the SOC is not only important for agricultural purposes: in recent years, the increasing attention towards global warming highlighted the crucial role of the soil in the global carbon cycle. In this context, soil spectroscopy is a well consolidated and widespread method to estimate soil variables exploiting the interaction between chromophores and electromagnetic radiation. The importance of spectroscopy in soil science is reflected by the increasing number of large soil spectral libraries collected in the world. These large libraries contain soil samples derived from a consistent number of pedological regions and thus from different parent material and soil types; this heterogeneity entails, in turn, a large variability in terms of mineralogical and organic composition. In the light of the huge variability of the spectral responses to SOC content and composition, a rigorous classification process is necessary to subset large spectral libraries and to avoid the calibration of global models failing to predict local variation in SOC content. In this regard, this study proposes a method to subset the European LUCAS topsoil database into soil classes using a clustering analysis based on a large number of soil properties. The LUCAS database was chosen to apply a standardized multivariate calibration approach valid for large areas without the need for extensive field and laboratory work for calibration of local models. Seven soil classes were detected by the clustering analyses and the samples belonging to each class were used to calibrate specific partial least square regression (PLSR) models to estimate SOC content of three local libraries collected in Belgium (Loam belt and Wallonia) and Luxembourg. The three local libraries only consist of spectral data (199 samples) acquired using the same protocol as the one used for the LUCAS database. SOC was estimated with a good accuracy both within each local library (RMSE: 1.2 ÷ 5.4 g kg-1; RPD: 1.41 ÷ 2.06) and for the samples of the three libraries together (RMSE: 3.9 g kg-1; RPD: 2.47). The proposed approach could allow to estimate SOC everywhere in Europe only collecting spectra, without the need for chemical laboratory analyses, exploiting the potentiality of the LUCAS database and specific PLSR models.

The Science and Application of Satellite Based Fire Radiative Energy

NASA Technical Reports Server (NTRS)

Ellicott, Evan; Vermote, Eric (Editor)

2012-01-01

The accurate measurement of ecosystem biomass is of great importance in scientific, resource management and energy sectors. In particular, biomass is a direct measurement of carbon storage within an ecosystem and of great importance for carbon cycle science and carbon emission mitigation. Remote Sensing is the most accurate tool for global biomass measurements because of the ability to measure large areas. Current biomass estimates are derived primarily from ground-based samples, as compiled and reported in inventories and ecosystem samples. By using remote sensing technologies, we are able to scale up the sample values and supply wall to wall mapping of biomass.

Improvement of core drill methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gatz, J.L.

1975-07-01

This report documents results of a program to evaluate effectiveness of more or less conventional subsurface samplers in obtaining representative and undisturbed samples of noncohesive alluvial materials containing large quantities of gravels and cobbles. This is the first phase of a research program to improve core drill methods. Samplers evaluated consisted of the Lawrence Livermore Laboratory membrane sampler, 4-in. Denison sampler, 6-in. Dension sampler, 5-in. Modified Denison sampler, and 3-in. thinwall drive tube. Small representative samples were obtained with the Dension samplers; no undisturbed samples were obtained. The field work was accomplished in the Rhodes Canyon area, White Sands Misslemore » Range, New Mexico.« less

Phanerozoic marine diversity: rock record modelling provides an independent test of large-scale trends.

PubMed

Smith, Andrew B; Lloyd, Graeme T; McGowan, Alistair J

2012-11-07

Sampling bias created by a heterogeneous rock record can seriously distort estimates of marine diversity and makes a direct reading of the fossil record unreliable. Here we compare two independent estimates of Phanerozoic marine diversity that explicitly take account of variation in sampling-a subsampling approach that standardizes for differences in fossil collection intensity, and a rock area modelling approach that takes account of differences in rock availability. Using the fossil records of North America and Western Europe, we demonstrate that a modelling approach applied to the combined data produces results that are significantly correlated with those derived from subsampling. This concordance between independent approaches argues strongly for the reality of the large-scale trends in diversity we identify from both approaches.

Soil Magnetism and Magnetic Anomalies at the Marshall's Pen Archaeological Site, Mandeville, Jamaica

NASA Astrophysics Data System (ADS)

Figueroa, E.; Sternberg, R. S.; Delle, J. A.; Lawrence, N. D.; McAdoo, B. G.; Savina, M. E.

2002-05-01

Marshall's Pen, a 1000-acre parcel of land in Mandeville, Jamaica, underlain by limestone bedrock and bauxite soils, served as a coffee plantation in the early 19th century. Two to three hundred slaves of African descent worked the plantation from AD 1802 until slavery was abolished in Jamaica in 1838. The goal of the archaeological program at Marshall's Pen is to complement what little is known about Jamaican slave society from the historical record. Geophysical prospection was conducted at Marshall's Pen by ten undergraduate students as part of a Keck Geology Consortium project in the summer of 1999. In the slaves' village consisting of living and domestic labor areas, G858 cesium vapor magnetometer readings were taken every 0.1 seconds along 49 profiles, each 50 m long and spaced 1 meter apart, and magnetic susceptibility readings were taken at 1-meter intervals. Seven significant magnetic anomalies (up to 100 nT peak-to-peak) were detected in the village. Two of these were found to be caused by a buried machete and an iron woodworking tool. Three anomalies were associated with a large area of black, burned soil. Archaeological testing in this area produced partially carbonized seeds, charcoal, ceramics that were smudged after manufacture, and cutlery; this evidence suggests a domestic kitchen area. In situ susceptibility readings were zero on bedrock and low on the bauxite soils. Susceptibility readings generally correlated with the magnetics, to values as high as 50 (x 10-6, volume specific SI) in the ``kitchen'' area, suggesting a source in the susceptibility contrast for these magnetic anomalies. Soil samples were collected from the bauxite outside the village, and from the village area in the summer of 2001; ten village sites were sampled away from the kitchen area, and four from the kitchen area. Five samples from each site were boxed, weighed, and measured for laboratory susceptibility measurements. Eleven samples outide the village had a geometric mean susceptibility of 144 (x 10-8, mass-specific SI); forty-nine samples from the ten village off-kitchen sites had a mean susceptibility of 105; twenty samples from the four village on-kitchen sites had a mean susceptibility of 821. One sample from a village off-kitchen site had a susceptibility of 1894 due to the head of a roofing nail included in the sample. Isothermal remanent magnetization experiments were carried out on one sample from most sites. Three samples from outside the village had ratios of IRM(0.1T)/IRM(1.0T) of 0.76, 0.5, and 0.74; ratios for ten samples from the village away from the kitchen were between 0.72-0.77; ratios for two samples from the village in the kitchen were more easily saturated with values of 0.90 and 1.0. The susceptibility and IRM results are consistent with reduction of hematite from sites outside the kitchen to magnetite or maghemite at sites within the kitchen area. The resulting higher susceptibilities could generate the magnetic anomalies in this area.

A Statistical Analysis of Data Used in Critical Decision Making by Secondary School Personnel.

ERIC Educational Resources Information Center

Dunn, Charleta J.; Kowitz, Gerald T.

Guidance decisions depend on the validity of standardized tests and teacher judgment records as measures of student achievement. To test this validity, a sample of 400 high school juniors, randomly selected from two large Gulf Coas t area schools, were administered the Iowa Tests of Educational Development. The nine subtest scores and each…

The Requirement for Vocational Skills in the Engineering Industry in the Areas of Modena and Vienna. Synthesis Report.

ERIC Educational Resources Information Center

Gatti, Mario; Mereu, Maria Grazia; Tagliaferro, Claudio; Markowitsch, Jorg; Neuberger, Robert

Requirements for vocational skills in the engineering industry in Modena, Italy, and Vienna, Austria, were studied. In Modena, employees of a representative sample of 90 small, medium, and large firms in the mechanical processing, agricultural machinery, and sports car manufacturing sectors were interviewed. In Vienna, data were collected through…

Speedy Acquisition of Surface-Contamination Samples

NASA Technical Reports Server (NTRS)

Puleo, J. R.; Kirschner, L. E.

1982-01-01

Biological contamination of large-area surfaces can be determined quickly, inexpensively, and accurately with the aid of a polyester bonded cloth. Cloth is highly effective in removing microbes from a surface and releasing them for biological assay. In releasing contaminants, polyester bonded cloth was found to be superior to other commercial cleanroom cloths, including spun-bound polyamid cloths and cellulose cloths.

Exploring Changes in Secondary Teachers' Learning Orientation through the Use of Literacy Coaching

ERIC Educational Resources Information Center

Lilly, Christopher

2012-01-01

This paper reports findings of a qualitative study exploring the changes in secondary teachers' learning orientation through the use of literacy coaching. The study took place within a large suburban district in the Chicagoland area and explores the question from the perspective of participants sampled across three departments and two campuses in…

Examining Mexican-Heritage Children's Representations of Relationships with Mothers and Teachers in Preschool

ERIC Educational Resources Information Center

Vu, Jennifer A.; Howes, Carollee

2012-01-01

Using narrative story-completion tasks with a sample of 97 preschool-age Mexican-heritage children from a large urban area, the authors examined differences in children's representations about their mothers and teachers. The authors also looked at teachers' perceptions to determine whether teachers viewed children in the same way as children…

Wide-field lensless fluorescent microscopy using a tapered fiber-optic faceplate on a chip.

PubMed

Coskun, Ahmet F; Sencan, Ikbal; Su, Ting-Wei; Ozcan, Aydogan

2011-09-07

We demonstrate lensless fluorescent microscopy over a large field-of-view of ~60 mm(2) with a spatial resolution of <4 µm. In this on-chip fluorescent imaging modality, the samples are placed on a fiber-optic faceplate that is tapered such that the density of the fiber-optic waveguides on the top facet is >5 fold larger than the bottom one. Placed on this tapered faceplate, the fluorescent samples are pumped from the side through a glass hemisphere interface. After excitation of the samples, the pump light is rejected through total internal reflection that occurs at the bottom facet of the sample substrate. The fluorescent emission from the sample is then collected by the smaller end of the tapered faceplate and is delivered to an opto-electronic sensor-array to be digitally sampled. Using a compressive sampling algorithm, we decode these raw lensfree images to validate the resolution (<4 µm) of this on-chip fluorescent imaging platform using microparticles as well as labeled Giardia muris cysts. This wide-field lensfree fluorescent microscopy platform, being compact and high-throughput, might provide a valuable tool especially for cytometry, rare cell analysis (involving large area microfluidic systems) as well as for microarray imaging applications.

The species-area relationship, self-similarity, and the true meaning of the z-value.

PubMed

Tjørve, Even; Tjørve, Kathleen M Calf

2008-12-01

The power model, S= cA(z) (where S is number of species, A is area, and c and z are fitted constants), is the model most commonly fitted to species-area data assessing species diversity. We use the self-similarity properties of this model to reveal patterns implicated by the z parameter. We present the basic arithmetic leading both to the fraction of new species added when two areas are combined and to species overlap between two areas of the same size, given a continuous sampling scheme. The fraction of new species resulting from expansion of an area can be expressed as alpha(z)-1, where alpha is the expansion factor. Consequently, z-values can be converted to a scale-invariant species overlap between two equally sized areas, since the proportion of species in common between the two areas is 2-2(z). Calculating overlap when adding areas of the same size reveals the intrinsic effect of distance assumed by the bisectional scheme. We use overlap area relationships from empirical data sets to illustrate how answers to the single large or several small reserves (SLOSS) question vary between data sets and with scale. We conclude that species overlap and the effect of distance between sample areas or isolates should be addressed when discussing species area relationships, and lack of fit to the power model can be caused by its assumption of a scale-invariant overlap relationship.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Timmermans, F. J.; Otto, C.

New developments in the field of microscopy enable to acquire increasing amounts of information from large sample areas and at an increased resolution. Depending on the nature of the technique, the information may reveal morphological, structural, chemical, and still other sample characteristics. In research fields, such as cell biology and materials science, there is an increasing demand to correlate these individual levels of information and in this way to obtain a better understanding of sample preparation and specific sample properties. To address this need, integrated systems were developed that combine nanometer resolution electron microscopes with optical microscopes, which produce chemicallymore » or label specific information through spectroscopy. The complementary information from electron microscopy and light microscopy presents an opportunity to investigate a broad range of sample properties in a correlated fashion. An important part of correlating the differences in information lies in bridging the different resolution and image contrast features. The trend to analyse samples using multiple correlated microscopes has resulted in a new research field. Current research is focused, for instance, on (a) the investigation of samples with nanometer scale distribution of inorganic and organic materials, (b) live cell analysis combined with electron microscopy, and (c) in situ spectroscopic and electron microscopy analysis of catalytic materials, but more areas will benefit from integrated correlative microscopy.« less

Contributed review: Review of integrated correlative light and electron microscopy.

PubMed

Timmermans, F J; Otto, C

2015-01-01

New developments in the field of microscopy enable to acquire increasing amounts of information from large sample areas and at an increased resolution. Depending on the nature of the technique, the information may reveal morphological, structural, chemical, and still other sample characteristics. In research fields, such as cell biology and materials science, there is an increasing demand to correlate these individual levels of information and in this way to obtain a better understanding of sample preparation and specific sample properties. To address this need, integrated systems were developed that combine nanometer resolution electron microscopes with optical microscopes, which produce chemically or label specific information through spectroscopy. The complementary information from electron microscopy and light microscopy presents an opportunity to investigate a broad range of sample properties in a correlated fashion. An important part of correlating the differences in information lies in bridging the different resolution and image contrast features. The trend to analyse samples using multiple correlated microscopes has resulted in a new research field. Current research is focused, for instance, on (a) the investigation of samples with nanometer scale distribution of inorganic and organic materials, (b) live cell analysis combined with electron microscopy, and (c) in situ spectroscopic and electron microscopy analysis of catalytic materials, but more areas will benefit from integrated correlative microscopy.

Volcanic activity and satellite-detected thermal anomalies at Central American volcanoes

NASA Technical Reports Server (NTRS)

Stoiber, R. E. (Principal Investigator); Rose, W. I., Jr.

1973-01-01

The author has identified the following significant results. A large nuee ardente eruption occurred at Santiaguito volcano, within the test area on 16 September 1973. Through a system of local observers, the eruption has been described, reported to the international scientific community, extent of affected area mapped, and the new ash sampled. A more extensive report on this event will be prepared. The eruption is an excellent example of the kind of volcanic situation in which satellite thermal imagery might be useful. The Santiaguito dome is a complex mass with a whole series of historically active vents. It's location makes access difficult, yet its activity is of great concern to large agricultural populations who live downslope. Santiaguito has produced a number of large eruptions with little apparent warning. In the earlier ground survey large thermal anomalies were identified at Santiaguito. There is no way of knowing whether satellite monitoring could have detected changes in thermal anomaly patterns related to this recent event, but the position of thermal anomalies on Santiaguito and any changes in their character would be relevant information.

On the origin of the Bangui magnetic anomaly, central African empire

NASA Technical Reports Server (NTRS)

Marsh, B. D.

1977-01-01

A large magnetic anomaly was recognized in satellite magnetometer data over the Central African Empire in central Africa. They named this anomaly the Bangui magnetic anomaly due to its location near the capital city of Bangui, C.A.E. Because large crustal magnetic anomalies are uncommon, the origin of this anomaly has provoked some interest. The area of the anomaly was visited to make ground magnetic measurements, geologic observations, and in-situ magnetic susceptibility measurements. Some rock samples were also collected and chemically analyzed. The results of these investigations are presented.

Microfluidic ultrasonic particle separators with engineered node locations and geometries

DOEpatents

Rose, Klint A.; Fisher, Karl A.; Wajda, Douglas A.; Mariella, Jr., Raymond P.; Bailey, Christopher; Dehlinger, Dietrich; Shusteff, Maxim; Jung, Byoungsok; Ness, Kevin D.

2016-04-26

An ultrasonic microfluidic system includes a separation channel for conveying a sample fluid containing small particles and large particles, flowing substantially parallel, adjacent to a recovery fluid, with which it is in contact. An acoustic transducer produces an ultrasound standing wave, that generates a pressure field having at least one node of minimum pressure amplitude. An acoustic extension structure is located proximate to said separation channel for positioning said acoustic node off center in said acoustic area and concentrating the large particles in said recovery fluid stream.

Microfluidic ultrasonic particle separators with engineered node locations and geometries

DOEpatents

Rose, Klint A; Fisher, Karl A; Wajda, Douglas A; Mariella, Jr., Raymond P; Bailey, Christopher; Dehlinger, Dietrich; Shusteff, Maxim; Jung, Byoungsok; Ness, Kevin D

2015-03-31

An ultrasonic microfluidic system includes a separation channel for conveying a sample fluid containing small particles and large particles, flowing substantially parallel, adjacent to a recovery fluid, with which it is in contact. An acoustic transducer produces an ultrasound standing wave, that generates a pressure field having at least one node of minimum, pressure amplitude. An acoustic extension structure is located proximate to said separation channel for positioning said acoustic node off center in said acoustic area and concentrating the large particles in said recovery fluid stream.

Microfluidic ultrasonic particle separators with engineered node locations and geometries

DOEpatents

Rose, Klint A; Fisher, Karl A; Wajda, Douglas A; Mariella, Jr., Raymond P; Bailey, Christoppher; Dehlinger, Dietrich; Shusteff, Maxim; Jung, Byoungsok; Ness, Kevin D

2014-05-20

An ultrasonic microfluidic system includes a separation channel for conveying a sample fluid containing small particles and large particles, flowing substantially parallel, adjacent to a recovery fluid, with which it is in contact. An acoustic transducer produces an ultrasound standing wave, that generates a pressure field having at least one node of minimum pressure amplitude. An acoustic extension structure is located proximate to said separation channel for positioning said acoustic node off center in said acoustic area and concentrating the large particles in said recovery fluid stream.

Residues of organochlorine pesticides in surface soil and raw foods from rural areas of the Republic of Tajikistan.

PubMed

Barron, Mace G; Ashurova, Zebunisso J; Kukaniev, Mukhamadcho A; Avloev, Hakbarqul K; Khaidarov, Karim K; Jamshedov, Jamshed N; Rahmatullova, Oygul S; Atolikshoeva, Sunbula S; Mamadshova, Sakina S; Manzenyuk, Oksana

2017-05-01

The central Asian Republic of Tajikistan has been an area of extensive historical agricultural pesticide use as well as large scale burials of banned chlorinated insecticides. The current investigation was a four year study of legacy organochlorine pesticides in surface soil and raw foods in four rural areas of Tajikistan. Study areas included the pesticide burial sites of Konibodom and Vakhsh, and family farms of Garm and Chimbuloq villages. These areas were selected to represent a diversity of pesticide disposal histories and to allow assessment of local pesticide contamination in Tajikistan. Each site was visited multiple times and over 500 samples of surface soil and raw foods were collected and analyzed for twenty legacy organochlorine pesticides. Various local food products were sampled to represent the range of raw foods potentially containing residues of banned pesticides, including dairy products, meat, edible plant and cotton seed products. The pesticide analytes included DDTs (DDT, DDD, DDE), lindane isomers (α, β, γ, δ BHC), endosulfan isomers (endosulfan I, II, sulfate), other cyclodienes (aldrin, α and γ chlordanes, dieldrin, endrin, endrin aldehyde and ketone, heptachlor, heptachlor epoxide), and methoxychlor. Pesticide analytes were selected based on availability of commercial standards and known or suspected historical pesticide use and burial. Pesticide contamination was highest in soil and generally low in meat, dairy, and plant products. DDT was consistently the highest measured individual pesticide at each of the four sampling areas, along with BHC isomers and endosulfan II. Soil concentrations of pesticides were extremely heterogeneous at the Vakhsh and Konibodam disposal sites with many soil samples greater than 10 ppm. In contrast, samples from farms in Chimbuloq and Garm had low concentrations of pesticides. Pesticide contamination in raw foods was generally low, indicating minimal transfer from the pesticide sites into local food chains. Published by Elsevier Ltd.

[Economic damage caused by lowered prices in the agro-food sector in areas contaminated by radioactive materials leaked from the nuclear power plant severely damaged by the 2011 Great East Japan Earthquake--consideration from the viewpoints of epidemiology, economics and social psychology].

PubMed

Sugita, Minoru; Miyakawa, Michiko

2013-01-01

Large amounts of radioactive materials were leaked into the environment from the Fukushima Daiichi Nuclear Power Plant (FDNPP) of the Tokyo Electric Power Company, which was severely damaged by the 2011 Tohoku Region Pacific Coast Earthquake and accompanying tsunami. Economic damage due to lowered prices and supplies of food products produced in the areas contaminated by the radioactive materials leaked from the damaged FDNPP to the agro-food sector in the affected areas is notable. In Japanese, this is known as fuhyo higai. In this study, we investigated fuhyo higai from the viewpoints of epidemiology, economics, and social psychology in an effort to seek solutions. Information was obtained from articles in print and on the Internet. Fuhyo higai, or economic damage of the agro-food sector, which is the main industry in the contaminated areas, is serious because it is difficult to reassure the general population regarding food safety. This fuhyo higai does not derive solely from rumor. It has been reported that improving the science literacy of the general population is important as a countermeasure against fuhyo higai, but this may not be effective because of the human social structure and behavior of people who seek subjective safety. Almost all radiological laboratory results of samples of food produced in the contaminated areas were below detectable limits. Very high values were rarely detected. In general, information about the dose-response relationship is obtained under the assumption that there may be error in the response but not in the dose. The rare cases of extremely high radiological values of food samples from the contaminated areas may correspond to large errors in dose. However, it is difficult to deny a high-dose risk. The reported information on the dose-response relationship obtained under the assumption that there is no error in dose is not sufficient. Thus, response, i.e., health risk, cannot be correctly estimated. This leads the general population to choose food products from areas far from the FDNPP over those from the contaminated areas. In order to resolve this problem, thorough decontamination of radioactive areas, including large forests, is necessary for the market to regain competitiveness to the level it was before the accident. The cost of such decontamination is enormous and requires much labor. Decontamination will create employment and is indispensable in restoring the deteriorated economic conditions of the affected areas.

Designing community surveys to provide a basis for noise policy

NASA Technical Reports Server (NTRS)

Fields, J. M.

1980-01-01

After examining reports from a large number of social surveys, two areas were identified where methodological improvements in the surveys would be especially useful for public policy. The two study areas are: the definition of noise indexes and the assessment of noise impact. Improvements in the designs of surveys are recommended which would increase the validity and reliability of the noise indexes. Changes in interview questions and sample designs are proposed which would enable surveys to provide measures of noise impact which are directly relevant for public policy.

Solute geochemistry of the Snake River plain regional aquifer system, Idaho and eastern Oregon

USGS Publications Warehouse

Wood, Warren W.; Low, Walton H.

1988-01-01

Geothermometry calculations of selected ground-water samples from known geothermal areas throughout the basin suggest that the geother- mal system is large in areal extent but has relatively low temperatures. Approximately half of the silica-quartz calculated water temperatures are greater than 90 °C. Radiocarbon dating of geothermal water in the Salmon Falls and Bruneau-Grand View areas in the south central part of the Snake River basin suggests that residence time of the geother- mal water is about 17,700 years.

LACIE performance predictor final operational capability program description, volume 3

NASA Technical Reports Server (NTRS)

1976-01-01

The requirements and processing logic for the LACIE Error Model program (LEM) are described. This program is an integral part of the Large Area Crop Inventory Experiment (LACIE) system. LEM is that portion of the LPP (LACIE Performance Predictor) which simulates the sample segment classification, strata yield estimation, and production aggregation. LEM controls repetitive Monte Carlo trials based on input error distributions to obtain statistical estimates of the wheat area, yield, and production at different levels of aggregation. LEM interfaces with the rest of the LPP through a set of data files.

Causes of toxicity in stormwater runoff from sawmills

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bailey, H.C.; Elphick, J.R.; Potter, A.

1999-07-01

Samples of stormwater runoff from nine sawmills in British Columbia, Canada, were tested for acute toxicity with juvenile rainbow trout over a 23-month period. Forty-two of the 58 samples tested exhibited toxicity. Causes of toxicity were investigated using toxicity identification evaluation techniques. Toxicity was attributed to divalent cations, particularly zinc, in 32 of the samples. The low hardness associated with most of the samples increased the potential for metal toxicity. For example, the LC50 of zinc was 14 {micro}g/L at a hardness of 5 mg/L. Toxicity in the remaining samples was largely attributed to tannins and lignins and was associatedmore » with areas of bulk log handling. No evidence was found to indicate that antisapstain chemicals applied to freshly cut wood contributed to toxicity.« less

Enhanced, targeted sampling of high-dimensional free-energy landscapes using variationally enhanced sampling, with an application to chignolin

PubMed Central

Shaffer, Patrick; Valsson, Omar; Parrinello, Michele

2016-01-01

The capabilities of molecular simulations have been greatly extended by a number of widely used enhanced sampling methods that facilitate escaping from metastable states and crossing large barriers. Despite these developments there are still many problems which remain out of reach for these methods which has led to a vigorous effort in this area. One of the most important problems that remains unsolved is sampling high-dimensional free-energy landscapes and systems that are not easily described by a small number of collective variables. In this work we demonstrate a new way to compute free-energy landscapes of high dimensionality based on the previously introduced variationally enhanced sampling, and we apply it to the miniprotein chignolin. PMID:26787868

Compiling and editing agricultural strata boundaries with remotely sensed imagery and map attribute data using graphics workstations

NASA Technical Reports Server (NTRS)

Cheng, Thomas D.; Angelici, Gary L.; Slye, Robert E.; Ma, Matt

1991-01-01

The USDA presently uses labor-intensive photographic interpretation procedures to delineate large geographical areas into manageable size sampling units for the estimation of domestic crop and livestock production. Computer software to automate the boundary delineation procedure, called the computer-assisted stratification and sampling (CASS) system, was developed using a Hewlett Packard color-graphics workstation. The CASS procedures display Thematic Mapper (TM) satellite digital imagery on a graphics display workstation as the backdrop for the onscreen delineation of sampling units. USGS Digital Line Graph (DLG) data for roads and waterways are displayed over the TM imagery to aid in identifying potential sample unit boundaries. Initial analysis conducted with three Missouri counties indicated that CASS was six times faster than the manual techniques in delineating sampling units.

At convenience and systematic random sampling: effects on the prognostic value of nuclear area assessments in breast cancer patients.

PubMed

Jannink, I; Bennen, J N; Blaauw, J; van Diest, P J; Baak, J P

1995-01-01

This study compares the influence of two different nuclear sampling methods on the prognostic value of assessments of mean and standard deviation of nuclear area (MNA, SDNA) in 191 consecutive invasive breast cancer patients with long term follow up. The first sampling method used was 'at convenience' sampling (ACS); the second, systematic random sampling (SRS). Both sampling methods were tested with a sample size of 50 nuclei (ACS-50 and SRS-50). To determine whether, besides the sampling methods, sample size had impact on prognostic value as well, the SRS method was also tested using a sample size of 100 nuclei (SRS-100). SDNA values were systematically lower for ACS, obviously due to (unconsciously) not including small and large nuclei. Testing prognostic value of a series of cut off points, MNA and SDNA values assessed by the SRS method were prognostically significantly stronger than the values obtained by the ACS method. This was confirmed in Cox regression analysis. For the MNA, the Mantel-Cox p-values from SRS-50 and SRS-100 measurements were not significantly different. However, for the SDNA, SRS-100 yielded significantly lower p-values than SRS-50. In conclusion, compared with the 'at convenience' nuclear sampling method, systematic random sampling of nuclei is not only superior with respect to reproducibility of results, but also provides a better prognostic value in patients with invasive breast cancer.

Large-scale Scanning Transmission Electron Microscopy (Nanotomy) of Healthy and Injured Zebrafish Brain.

PubMed

Kuipers, Jeroen; Kalicharan, Ruby D; Wolters, Anouk H G; van Ham, Tjakko J; Giepmans, Ben N G

2016-05-25

Large-scale 2D electron microscopy (EM), or nanotomy, is the tissue-wide application of nanoscale resolution electron microscopy. Others and we previously applied large scale EM to human skin pancreatic islets, tissue culture and whole zebrafish larvae(1-7). Here we describe a universally applicable method for tissue-scale scanning EM for unbiased detection of sub-cellular and molecular features. Nanotomy was applied to investigate the healthy and a neurodegenerative zebrafish brain. Our method is based on standardized EM sample preparation protocols: Fixation with glutaraldehyde and osmium, followed by epoxy-resin embedding, ultrathin sectioning and mounting of ultrathin-sections on one-hole grids, followed by post staining with uranyl and lead. Large-scale 2D EM mosaic images are acquired using a scanning EM connected to an external large area scan generator using scanning transmission EM (STEM). Large scale EM images are typically ~ 5 - 50 G pixels in size, and best viewed using zoomable HTML files, which can be opened in any web browser, similar to online geographical HTML maps. This method can be applied to (human) tissue, cross sections of whole animals as well as tissue culture(1-5). Here, zebrafish brains were analyzed in a non-invasive neuronal ablation model. We visualize within a single dataset tissue, cellular and subcellular changes which can be quantified in various cell types including neurons and microglia, the brain's macrophages. In addition, nanotomy facilitates the correlation of EM with light microscopy (CLEM)(8) on the same tissue, as large surface areas previously imaged using fluorescent microscopy, can subsequently be subjected to large area EM, resulting in the nano-anatomy (nanotomy) of tissues. In all, nanotomy allows unbiased detection of features at EM level in a tissue-wide quantifiable manner.

Large-scale Scanning Transmission Electron Microscopy (Nanotomy) of Healthy and Injured Zebrafish Brain

PubMed Central

Kuipers, Jeroen; Kalicharan, Ruby D.; Wolters, Anouk H. G.

2016-01-01

Large-scale 2D electron microscopy (EM), or nanotomy, is the tissue-wide application of nanoscale resolution electron microscopy. Others and we previously applied large scale EM to human skin pancreatic islets, tissue culture and whole zebrafish larvae1-7. Here we describe a universally applicable method for tissue-scale scanning EM for unbiased detection of sub-cellular and molecular features. Nanotomy was applied to investigate the healthy and a neurodegenerative zebrafish brain. Our method is based on standardized EM sample preparation protocols: Fixation with glutaraldehyde and osmium, followed by epoxy-resin embedding, ultrathin sectioning and mounting of ultrathin-sections on one-hole grids, followed by post staining with uranyl and lead. Large-scale 2D EM mosaic images are acquired using a scanning EM connected to an external large area scan generator using scanning transmission EM (STEM). Large scale EM images are typically ~ 5 - 50 G pixels in size, and best viewed using zoomable HTML files, which can be opened in any web browser, similar to online geographical HTML maps. This method can be applied to (human) tissue, cross sections of whole animals as well as tissue culture1-5. Here, zebrafish brains were analyzed in a non-invasive neuronal ablation model. We visualize within a single dataset tissue, cellular and subcellular changes which can be quantified in various cell types including neurons and microglia, the brain's macrophages. In addition, nanotomy facilitates the correlation of EM with light microscopy (CLEM)8 on the same tissue, as large surface areas previously imaged using fluorescent microscopy, can subsequently be subjected to large area EM, resulting in the nano-anatomy (nanotomy) of tissues. In all, nanotomy allows unbiased detection of features at EM level in a tissue-wide quantifiable manner. PMID:27285162

A review of empirical research related to the use of small quantitative samples in clinical outcome scale development.

PubMed

Houts, Carrie R; Edwards, Michael C; Wirth, R J; Deal, Linda S

2016-11-01

There has been a notable increase in the advocacy of using small-sample designs as an initial quantitative assessment of item and scale performance during the scale development process. This is particularly true in the development of clinical outcome assessments (COAs), where Rasch analysis has been advanced as an appropriate statistical tool for evaluating the developing COAs using a small sample. We review the benefits such methods are purported to offer from both a practical and statistical standpoint and detail several problematic areas, including both practical and statistical theory concerns, with respect to the use of quantitative methods, including Rasch-consistent methods, with small samples. The feasibility of obtaining accurate information and the potential negative impacts of misusing large-sample statistical methods with small samples during COA development are discussed.

Mineral resource potential of the Middle Santiam Roadless Area, Linn County, Oregon

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walker, G.W.

1984-01-01

This report discusses the results of a mineral survey of the Middle Santiam Roadless Area (06929), Willamette National Forest, Linn County Oregon. Middle Santiam Roadless Area is adjacent on the east of the Quartzville mining district, a district that has yielded small amounts of base- and precious-metal ores. Many rock types and alteration features that characterize the mining district occur only the western part of the roadless area, and analysis of a few samples from this part of the roadless area indicates evidence of weak mineralization. The western part of the roadless area is therefore identified as having a moderatemore » potential for small deposits of base and precious metals and a low potential for large very low-grade precious-metal deposits. The eastern part of the roadless area has a low potential for metalliferous deposits. 7 refs., 4 figs., 1 tab.« less

Humanitarian Needs Among Displaced and Female-Headed Households in Government-Controlled Areas of Syria.

PubMed

Doocy, Shannon; Lyles, Emily

2017-06-01

To identify unmet needs and assistance priorities of displaced and female-headed households in government-controlled areas of Syria. In mid-2016, we undertook a survey of accessible areas, largely urban and government-controlled, to identify unmet needs and assistance priorities. We used a cluster design with probability sampling to attain a final sample of 2405 households from 10 of 14 governorates; 31 of 65 (47.7%) districts were included that are home to 38.1% of people in need. Displaced and female-headed households were more vulnerable than nondisplaced and male-headed households in numerous sectors. Despite approximately half of surveyed households reporting receipt of humanitarian assistance in the preceding month and apparently effective targeting of assistance by vulnerability, unmet needs were nearly ubiquitous. The humanitarian situation in inaccessible areas of Syria is likely to be considerably worse; thus, findings presented here likely underestimate humanitarian needs. Efforts to expand support to Syria's most vulnerable households are desperately needed as are innovative targeting and modalities that enable more efficient and effective assistance.

Baseline study on essential and trace elements in polished rice from South Korea.

PubMed

Jung, Myung Chae; Yun, Seong-Taek; Lee, Jin-Soo; Lee, Jong-Un

2005-09-01

In 2000, 63 (polished) white rice samples were collected in eight administrative areas all over South Korea and analyzed for 16 elements by inductively coupled plasma atomic emission spectrometry (ICP-AES). Potassium had the highest content, next to Mg, Ca, Si, Zn, Na, Al and Fe. Most of the samples contained worldwide average concentrations of essential and trace elements in rice grains reported by various researches. For inter-area differences in those elements in the rice, the statistical analysis showed no significant differences (p > 0.05) among the eight administrative areas, suggesting that inter-area differences were not substantial in most cases. Thus, the present data can be used as national background levels of elements in rice produced in South Korea. Using the published data on daily consumption of rice in South Korea, it was possible to estimate the daily intake of As, Cd, Cu, Pb and Zn via rice. The results showed that a regular consumption of rice produced in Korea plays an important role in accumulation of essential and trace elements in Korean, especially for farm-households consuming relatively large amounts of rice.

System for analysis of LANDSAT agricultural data: Automatic computer-assisted proportion estimation of local areas

NASA Technical Reports Server (NTRS)

Nalepka, R. F. (Principal Investigator); Kauth, R. J.; Thomas, G. S.

1976-01-01

The author has identified the following significant results. A conceptual man machine system framework was created for a large scale agricultural remote sensing system. The system is based on and can grow out of the local recognition mode of LACIE, through a gradual transition wherein computer support functions supplement and replace AI functions. Local proportion estimation functions are broken into two broad classes: (1) organization of the data within the sample segment; and (2) identification of the fields or groups of fields in the sample segment.

Identification of stochastic interactions in nonlinear models of structural mechanics

NASA Astrophysics Data System (ADS)

Kala, Zdeněk

2017-07-01

In the paper, the polynomial approximation is presented by which the Sobol sensitivity analysis can be evaluated with all sensitivity indices. The nonlinear FEM model is approximated. The input area is mapped using simulations runs of Latin Hypercube Sampling method. The domain of the approximation polynomial is chosen so that it were possible to apply large number of simulation runs of Latin Hypercube Sampling method. The method presented also makes possible to evaluate higher-order sensitivity indices, which could not be identified in case of nonlinear FEM.

Palaeoenvironmental reconstructions on the Mozambique coast as a tool to understand human evolution: from modern analogues to borehole interpretation

NASA Astrophysics Data System (ADS)

Gomes, Ana; Skosey-LaLonde, Elena; Zinsious, Brandon; Gonçalves, Célia; Bicho, Nuno; Raja, Mussa; Cascalheira, João; Haws, Jonathan

2017-04-01

In the framework of the project "Stone Age Vilankulos: Modern Human Origins Research South of the Rio Save, Mozambique" a geoarchaeological survey was conducted in 2016 aiming to better understand the environmental history and landscape evolution of the study area including the environmental context of human occupation. During the survey, 23 sediment surface samples were collected across a variety of environments, namely: freshwater environment - Elephant River basin in Southwestern Mozambique - and brackish and marine tidal environments - Inhambane coastal area, Southeastern Mozambique. These samples will be used as modern analogues to interpret the sedimentological and paleontological record of 4 cores collected in a mangrove area of the Inhambane estuary and then reconstruct its palaeoenvironmental evolution. All the sampling points were georeferenced and the study area was overflown with a drone to collect photogrammetric data. Both surface and core samples were used for diatom, texture and geochemical analysis. Diatoms will be used as the main palaeontological proxy, because they are unicellular algae with a short-live cycle and largely sensible to environmental variables such as salinity, sediment texture and duration of the tidal inundation. Preliminary data on the modern diatoms analysis showed that diatom diversity is high and the equitability is low in all environments. Cores sedimentological description and dating are also presented. The work was supported by the project PTDC/EPHARQ/4168/2014, funded by the Portuguese Foundation for Science and Technology.

Atmospheric mercury in Changbai Mountain area, northeastern China II. The distribution of reactive gaseous mercury and particulate mercury and mercury deposition fluxes.

PubMed

Wan, Qi; Feng, Xinbin; Lu, Julia; Zheng, Wei; Song, Xinjie; Li, Ping; Han, Shijie; Xu, Hao

2009-08-01

Reactive gaseous mercury (RGM) and particulate mercury (Hgp) concentrations in ambient air from a remote site at Changbai Mountain area in northeastern China were intermittently monitored from August 2005 to July 2006 totaling 93 days representing fall, winter-spring and summer season, respectively. Rainwater and snow samples were collected during a whole year, and total mercury (THg) in rain samples were used to calculate wet depositional flux. A throughfall method and a model method were used to estimate dry depositional flux. Results showed mean concentrations of RGM and Hgp are 65 and 77 pg m(-3). Compared to background concentrations of atmospheric mercury species in Northern Hemisphere, RGM and Hgp are significantly elevated in Changbai area. Large values for standard deviation indicated fast reactivity and a low residence time for these mercury species. Seasonal variability is also important, with lower mercury levels in summer compared to other seasons, which is attributed to scavenging by rainfall and low local mercury emissions in summer. THg concentrations ranged from 11.5 to 15.9 ng L(-1) in rainwater samples and 14.9-18.6 ng L(-1) in throughfall samples. Wet depositional flux in Changbai area is calculated to be 8.4 microg m(-2) a(-1), and dry deposition flux is estimated to be 16.5 microg m(-2) a(-1) according to a throughfall method and 20.2 microg m(-2) a(-1) using a model method.

USGS environmental characterization of flood sediments left in the New Orleans area after Hurricanes Katrina and Rita, 2005--Progress Report

USGS Publications Warehouse

Plumlee, Geoffrey S.; Meeker, Gregory P.; Lovelace, John K.; Rosenbauer, Robert J.; Lamothe, Paul J.; Furlong, Edward T.; Demas, Charles R.

2006-01-01

Introduction: The flooding in the greater New Orleans area that resulted from Hurricanes Katrina and Rita in September, 2005, left behind accumulations of sediments up to many centimeters thick on streets, lawns, parking lots, and other flat surfaces. These flood sediment deposits have been the focus of extensive study by the US Environmental Protection Agency (EPA) and Louisiana Department of Environmental Quality (LDEQ) due to concerns that the sediments may contain elevated levels of heavy metals, organic contaminants, and microbes. The U.S. Geological Survey (USGS) is characterizing a limited number of flood sediment samples that were collected on September 15-16 and October 6-7, 2005, from the greater New Orleans area by personnel from the USGS Louisiana Water Science Center in Baton Rouge. Small samples (< 3 pints each) of wet to dry flood sediment were collected from 11 localities around downtown New Orleans on September 15, 2005, and two large samples (40 pints each) of wet flood sediment were collected from the Chalmette area on September 16. Twelve additional samples (8-10 pints each) were collected from New Orleans, Slidell, Rigolets, and Violet on October 6 and 7. The USGS characterization studies of these flood sediments are designed to produce data and interpretations regarding how the sediments and any contained contaminants may respond to environmental processes. This information will be of use to cleanup managers and DoI/USGS scientists assessing environmental impacts of the hurricanes and subsequent cleanup activities.

The relation of ground-water quality to housing density, Cape Cod, Massachusetts

USGS Publications Warehouse

Persky, J.H.

1986-01-01

Correlation of median nitrate concentration in groundwater with housing density for 18 sample areas on Cape Cod yields a Pearson correlation coefficient of 0.802, which is significant at the 95 % confidence level. In five of nine sample areas where housing density is greater than one unit/acre, nitrate concentrations exceed 5 mg of nitrate/L (the Barnstable County planning goal for nitrate) in 25% of wells. Nitrate concentrations exceed 5 mg of nitrogen/L in 25% of wells in only one of nine sample areas where housing density is less than one unit/acre. Median concentrations of sodium and iron, and median levels of pH and specific conductance, are not significantly correlated with housing density. A computer generated map of nitrate shows a positive relation between nitrate concentration and housing density on Cape Cod. However, the presence of septage- or sewage-disposal sites and fertilizer use are also important factors that affect the nitrate concentration. A map of specific conductance also shows a positive relation to housing density, but little or no relation between housing density and sodium, ammonia, pH, or iron is apparent on the maps. Chemical analyses of samples collected from 3,468 private- and public-supply wells between January 1980 and June 1984 were used to examine the extent to which housing density determines water quality on Cape Cod, an area largely unsewered and underlain by a sole source aquifer. (Author 's abstract)

Geochemical Data for Samples Collected in 2007 Near the Concealed Pebble Porphyry Cu-Au-Mo Deposit, Southwest Alaska

USGS Publications Warehouse

Fey, David L.; Granitto, Matthew; Giles, Stuart A.; Smith, Steven M.; Eppinger, Robert G.; Kelley, Karen D.

2008-01-01

In the summer of 2007, the U.S. Geological Survey (USGS) began an exploration geochemical research study over the Pebble porphyry copper-gold-molydenum (Cu-Au-Mo) deposit in southwest Alaska. The Pebble deposit is extremely large and is almost entirely concealed by tundra, glacial deposits, and post-Cretaceous volcanic and volcaniclastic rocks. The deposit is presently being explored by Northern Dynasty Minerals, Ltd., and Anglo-American LLC. The USGS undertakes unbiased, broad-scale mineral resource assessments of government lands to provide Congress and citizens with information on national mineral endowment. Research on known deposits is also done to refine and better constrain methods and deposit models for the mineral resource assessments. The Pebble deposit was chosen for this study because it is concealed by surficial cover rocks, it is relatively undisturbed (except for exploration company drill holes), it is a large mineral system, and it is fairly well constrained at depth by the drill hole geology and geochemistry. The goals of the USGS study are (1) to determine whether the concealed deposit can be detected with surface samples, (2) to better understand the processes of metal migration from the deposit to the surface, and (3) to test and develop methods for assessing mineral resources in similar concealed terrains. This report presents analytical results for geochemical samples collected in 2007 from the Pebble deposit and surrounding environs. The analytical data are presented digitally both as an integrated Microsoft 2003 Access? database and as Microsoft 2003 Excel? files. The Pebble deposit is located in southwestern Alaska on state lands about 30 km (18 mi) northwest of the village of Illiamna and 320 km (200 mi) southwest of Anchorage (fig. 1). Elevations in the Pebble area range from 287 m (940 ft) at Frying Pan Lake just south of the deposit to 1146 m (3760 ft) on Kaskanak Mountain about 5 km (5 mi) to the west. The deposit is in an area of relatively subdued topographic relief with an elevation of around 300 m (1000 ft). This portion of Alaska is part of the subarctic regime mountains division, Yukon intermontane plateaus-tayga-meadow province ecoregion, as defined by Bailey (U.S. Forest Service, 2007). Between June 28th and July 12th, 2007, scientists from the USGS collected soil, water, stream sediment, vegetation, heavy-mineral concentrate, till, and rock samples from the deposit area. This report contains analytical results for soil, water, stream sediment, and vegetation samples. Analyses for the heavy-mineral concentrate, till, and rock samples are still in progress. The sampling was undertaken during relatively dry and stable weather conditions. Only minor scattered rain showers occurred during the sampling period, so surface conditions were largely unaffected by weather. The predominant sample media collected were soils and surface waters. Soil and water (mostly from ponds and springs, some from small creeks) samples were collected along a single 7.8 km-long (4.8 mi) east-west traverse across the Pebble East and Pebble West zones and from more distal background areas around Koktuli and Kaskanak Mountains. Sample sites are shown on figure 2 and plate 1, and locality coordinates are provided in the accompanying Access and Excel files named FieldSite. Water samples were analyzed by USGS laboratories with one subset analyzed by Activation Laboratories (Actlabs), as indicated below. Soils and stream sediments were analyzed for their total content by SGS Minerals Services under a contract with the USGS. Soil samples were also leached by selected partial-extraction leaching procedures and then analyzed by several commercial laboratories, as described below. Vegetation samples were analyzed as indicated below.

Does size matter? Statistical limits of paleomagnetic field reconstruction from small rock specimens

NASA Astrophysics Data System (ADS)

Berndt, Thomas; Muxworthy, Adrian R.; Fabian, Karl

2016-01-01

As samples of ever decreasing sizes are being studied paleomagnetically, care has to be taken that the underlying assumptions of statistical thermodynamics (Maxwell-Boltzmann statistics) are being met. Here we determine how many grains and how large a magnetic moment a sample needs to have to be able to accurately record an ambient field. It is found that for samples with a thermoremanent magnetic moment larger than 10-11Am2 the assumption of a sufficiently large number of grains is usually given. Standard 25 mm diameter paleomagnetic samples usually contain enough magnetic grains such that statistical errors are negligible, but "single silicate crystal" works on, for example, zircon, plagioclase, and olivine crystals are approaching the limits of what is physically possible, leading to statistic errors in both the angular deviation and paleointensity that are comparable to other sources of error. The reliability of nanopaleomagnetic imaging techniques capable of resolving individual grains (used, for example, to study the cloudy zone in meteorites), however, is questionable due to the limited area of the material covered.

High-throughput Raman chemical imaging for evaluating food safety and quality

NASA Astrophysics Data System (ADS)

Qin, Jianwei; Chao, Kuanglin; Kim, Moon S.

2014-05-01

A line-scan hyperspectral system was developed to enable Raman chemical imaging for large sample areas. A custom-designed 785 nm line-laser based on a scanning mirror serves as an excitation source. A 45° dichroic beamsplitter reflects the laser light to form a 24 cm x 1 mm excitation line normally incident on the sample surface. Raman signals along the laser line are collected by a detection module consisting of a dispersive imaging spectrograph and a CCD camera. A hypercube is accumulated line by line as a motorized table moves the samples transversely through the laser line. The system covers a Raman shift range of -648.7-2889.0 cm-1 and a 23 cm wide area. An example application, for authenticating milk powder, was presented to demonstrate the system performance. In four minutes, the system acquired a 512x110x1024 hypercube (56,320 spectra) from four 47-mm-diameter Petri dishes containing four powder samples. Chemical images were created for detecting two adulterants (melamine and dicyandiamide) that had been mixed into the milk powder.

Experimental study on microsphere assisted nanoscope in non-contact mode

NASA Astrophysics Data System (ADS)

Ling, Jinzhong; Li, Dancui; Liu, Xin; Wang, Xiaorui

2018-07-01

Microsphere assisted nanoscope was proposed in existing literatures to capture super-resolution images of the nano-structures beneath the microsphere attached on sample surface. In this paper, a microsphere assisted nanoscope working in non-contact mode is designed and demonstrated, in which the microsphere is controlled with a gap separated to sample surface. With a gap, the microsphere is moved in parallel to sample surface non-invasively, so as to observe all the areas of interest. Furthermore, the influence of gap size on image resolution is studied experimentally. Only when the microsphere is close enough to the sample surface, super-resolution image could be obtained. Generally, the resolution decreases when the gap increases as the contribution of evanescent wave disappears. To keep an appropriate gap size, a quantitative method is implemented to estimate the gap variation by observing Newton's rings around the microsphere, serving as a real-time feedback for tuning the gap size. With a constant gap, large-area image with high resolution can be obtained during microsphere scanning. Our study of non-contact mode makes the microsphere assisted nanoscope more practicable and easier to implement.

Microstructural examination of

NASA Astrophysics Data System (ADS)

Fukuoka, C.; Yoshizawa, H.; Nakagawa, Y. G.; Lapides, M. E.

1993-10-01

Fatigue tests were performed to examine how microstructural conditioning influences crack initiation and propagation in SA508 class 3 low-carbon steel. A 3-mm-long crack was introduced in compact tension (CT) fatigue test specimens under four different loads in order to obtain crack tip plastic zones at different stress intensity factor ranges, ΔK = 18, 36, 54, and 72 MPa√m. The microstructure of the plastic zones around the crack tip were examined by trans- mission electron microscopy (TEM) and selected area electron diffraction (SAD). Micro- orientation of the dislocation cells in the plastic zones of all of the CT samples increased to 4 deg from the level of an as-received sample. Four-point bending fatigue tests were performed for plate shape samples with a large cyclic strain range. The SAD value of the bending samples was also 4 deg in the damaged area where cracks already initiated at an early stage of the fatigue process. These test results indicate that the microstructural conditioning is a prerequisite for the fatigue crack initiation and propagation in SA508. These observations may lead to better under- standing of how fatigue initiation processes transit to cracks.

The Vimos VLT deep survey. Global properties of 20,000 galaxies in the IAB < 22.5 WIDE survey

NASA Astrophysics Data System (ADS)

Garilli, B.; Le Fèvre, O.; Guzzo, L.; Maccagni, D.; Le Brun, V.; de la Torre, S.; Meneux, B.; Tresse, L.; Franzetti, P.; Zamorani, G.; Zanichelli, A.; Gregorini, L.; Vergani, D.; Bottini, D.; Scaramella, R.; Scodeggio, M.; Vettolani, G.; Adami, C.; Arnouts, S.; Bardelli, S.; Bolzonella, M.; Cappi, A.; Charlot, S.; Ciliegi, P.; Contini, T.; Foucaud, S.; Gavignaud, I.; Ilbert, O.; Iovino, A.; Lamareille, F.; McCracken, H. J.; Marano, B.; Marinoni, C.; Mazure, A.; Merighi, R.; Paltani, S.; Pellò, R.; Pollo, A.; Pozzetti, L.; Radovich, M.; Zucca, E.; Blaizot, J.; Bongiorno, A.; Cucciati, O.; Mellier, Y.; Moreau, C.; Paioro, L.

2008-08-01

The VVDS-Wide survey has been designed to trace the large-scale distribution of galaxies at z ~ 1 on comoving scales reaching ~100~h-1 Mpc, while providing a good control of cosmic variance over areas as large as a few square degrees. This is achieved by measuring redshifts with VIMOS at the ESO VLT to a limiting magnitude IAB = 22.5, targeting four independent fields with sizes of up to 4 deg2 each. We discuss the survey strategy which covers 8.6 deg2 and present the general properties of the current redshift sample. This includes 32 734 spectra in the four regions, covering a total area of 6.1 deg2 with a sampling rate of 22 to 24%. This paper accompanies the public release of the first 18 143 redshifts of the VVDS-Wide survey from the 4 deg2 contiguous area of the F22 field at RA = 22^h. We have devised and tested an objective method to assess the quality of each spectrum, providing a compact figure-of-merit. This is particularly effective in the case of long-lasting spectroscopic surveys with varying observing conditions. Our figure of merit is a measure of the robustness of the redshift measurement and, most importantly, can be used to select galaxies with uniform high-quality spectra to carry out reliable measurements of spectral features. We also use the data available over the four independent regions to directly measure the variance in galaxy counts. We compare it with general predictions from the observed galaxy two-point correlation function at different redshifts and with that measured in mock galaxy surveys built from the Millennium simulation. The purely magnitude-limited VVDS Wide sample includes 19 977 galaxies, 304 type I AGNs, and 9913 stars. The redshift success rate is above 90% independent of magnitude. A cone diagram of the galaxy spatial distribution provides us with the current largest overview of large-scale structure up to z ~ 1, showing a rich texture of over- and under-dense regions. We give the mean N(z) distribution averaged over 6.1 deg2 for a sample limited in magnitude to IAB = 22.5. Comparing galaxy densities from the four fields shows that in a redshift bin Δz = 0.1 at z ~ 1 one still has factor-of-two variations over areas as large as ~ 0.25 deg2. This level of cosmic variance agrees with that obtained by integrating the galaxy two-point correlation function estimated from the F22 field alone. It is also in fairly good statistical agreement with that predicted by the Millennium simulations. The VVDS WIDE survey currently provides the largest area coverage among redshift surveys reaching z ~ 1. The variance estimated over the survey fields shows explicitly how clustering results from deep surveys of even 1 deg2 size should be interpreted with caution. The survey data represent a rich data base to select complete sub-samples of high-quality spectra and to study galaxy ensemble properties and galaxy clustering over unprecedented scales at these redshifts. The redshift catalog of the 4 deg2 F22 field is publicly available at http://cencosw.oamp.fr.

Water quality and benthic fauna biodiversity in a unique small wetland at Messinia, Greece.

PubMed

Gritzalis, Konstantinos C; Anastasopoulou, Evangelia; Georgiopoulos, Nikolaos A; Markogianni, Vasiliki V; Skoulikidis, Nikolaos Th

2015-01-01

The wetland of Aghios Floros is located in the Prefecture of Messinia (S. W. Peloponnese, Greece) and occupies a small area, covered permanentlywith water. Flooding of the surrounding area is defended by an artificial channel that discharge large quantity of water into Pamisos River in whose river basin the Aghios Floros station belongs. At the sampling site various physico-chemical and conventional pollution parameters as well as hydrochemical variables were measured during the wet and the dry period of 2011. The hydromorphological and multihabitat approach of RIVPACS method was applied in situ, which gives an overall image of the landscape. The site was classified as 'Good' according to the Greek River Nutrient Classification System (GR.NCS) and the benthic macroinvertebrate fauna assemblages that dominated the area pointed out a 'Good' biological status as well. The biotic and abiotic sample processing, carried out in compliance with the demands of the Water Framework Directive, in general revealed high ecological status of the station. Specifically, a rich diversity and abundance of some macroinvertebrate families was recorded and regarding the aquatic flora the area is dominated by the water lilies species of Nymphaea alba which are unique in the area of Peloponnese.

Using excess 4He to quantify variability in aquitard leakage

NASA Astrophysics Data System (ADS)

Gardner, W. Payton; Harrington, Glenn A.; Smerdon, Brian D.

2012-10-01

SummaryFluid flux through aquitards controls the rate of recharge, discharge, cross-formational fluid flow and contaminant transport in subsurface systems. In this paper, concentrations of 4He are used to investigate the spatial distribution of vertical fluid flux through the regionally extensive Great Artesian Basin aquitard system in northern South Australia. Two vertical profiles of 4He concentration in aquitard pore water, augmented with regional sampling of aquifers above and below the aquitard were used to estimate fluid flux at multiple locations over a large spatial area. 4He concentrations in the shallow aquifer above the Great Artesian Basin range from atmospheric equilibrium to 1000 times enriched over atmosphere. Fluid flux through the aquitard was estimated by fitting observed helium concentrations at each sampling site with a 1-D model of helium transport through the aquitard. Estimated fluid fluxes through the aquitard vary over three orders of magnitude across the study area. In areas of competent aquitard, fluid fluxes are less than 0.003 mm/yr, and mass transport of helium is dominated by molecular diffusion. Preferential discharge zones are clearly identifiable with fluid fluxes up to 3 mm/yr. Our results show that fluid flux through a regionally extensive aquitard can be highly variable at large spatial scales, and that 4He concentrations in aquifers bounding the aquitard system provide a convenient and sensitive method for investigating aquitard flux at the regional scale.

Bamboo Classification Using WorldView-2 Imagery of Giant Panda Habitat in a Large Shaded Area in Wolong, Sichuan Province, China

PubMed Central

Tang, Yunwei; Jing, Linhai; Li, Hui; Liu, Qingjie; Yan, Qi; Li, Xiuxia

2016-01-01

This study explores the ability of WorldView-2 (WV-2) imagery for bamboo mapping in a mountainous region in Sichuan Province, China. A large area of this place is covered by shadows in the image, and only a few sampled points derived were useful. In order to identify bamboos based on sparse training data, the sample size was expanded according to the reflectance of multispectral bands selected using the principal component analysis (PCA). Then, class separability based on the training data was calculated using a feature space optimization method to select the features for classification. Four regular object-based classification methods were applied based on both sets of training data. The results show that the k-nearest neighbor (k-NN) method produced the greatest accuracy. A geostatistically-weighted k-NN classifier, accounting for the spatial correlation between classes, was then applied to further increase the accuracy. It achieved 82.65% and 93.10% of the producer’s and user’s accuracies respectively for the bamboo class. The canopy densities were estimated to explain the result. This study demonstrates that the WV-2 image can be used to identify small patches of understory bamboos given limited known samples, and the resulting bamboo distribution facilitates the assessments of the habitats of giant pandas. PMID:27879661

LAD-C: A large area debris collector on the ISS

NASA Technical Reports Server (NTRS)

Liou, J.-C.; Giovane, F. J.; Corsaro, R. D.; Burchell, M. J.; Drolshagen, G.; Kawai, H.; Stansbery, E. G.; Tabata, M.; Westphal, A. J.; Yano, H.

2006-01-01

The Large Area Debris Collector (LAD-C) is a 10 sq m aerogel and acoustic sensor system under development by the U.S. Naval Research Laboratory (NRL) with main collaboration from the NASA Orbital Debris Program Office at Johnson Space Center, JAXA Institute of Space and Astronautical Science (ISAS), Chiba University (Japan), ESA Space Debris Office, University of California at Berkeley, and University of Kent at Canterbury (UK). The U.S. Department of Defense (DoD) Space Test Program (STP) has assumed the responsibility for having the system manifested and deployed on the International Space Station (ISS), and then having it retrieved and returned to Earth after one to two years. LAD-C will attempt to utilize the ISS as a scientific platform to characterize the near-Earth meteoroid and orbital debris environment in the size regime where little data exist. In addition to meteoroid and orbital debris sample return, the acoustic sensors will record impact time, location, signal strength, and acoustic waveform data of the largest collected samples. A good time-dependent meteoroid and orbital debris flux estimate can be derived. Analysis of the data will also enable potential source identification of some of the collected samples. This dynamical link can be combined with laboratory composition analysis of impact residuals extracted from aerogel to further our understanding of orbital debris population, and the sources of meteoroids, asteroids and comets.

Hyperspectral Analysis for Standoff Detection of Dimethyl ...

EPA Pesticide Factsheets

Journal Article Detecting organophosphates in indoor settings requires more efficient and faster methods of surveying large surface areas than conventional approaches, which sample small surface areas followed by extraction and analysis. This study examined a standoff detection technique utilizing hyperspectral imaging for analysis of building materials in near-real time. In this proof-of-concept study, dimethyl methylphosphonate (DMMP) was applied to stainless steel and laminate coupons and spectra were collected during active illumination. Absorbance bands at approximately 1275 cm-1 and 1050 cm-1 were associated with phosphorus-oxygen double bond (P=O) and phosphorus-oxygen-carbon (P-O-C) bond stretches of DMMP, respectively. The magnitude of these bands increased linearly (r2 = 0.93) with DMMP across the full absorbance spectrum, between ν1 = 877 cm-1 to ν2 = 1262 cm-1. Comparisons between bare and contaminated surfaces on stainless steel using the spectral contrast angle technique indicated that the bare samples showed no sign of contamination, with large uniformly distributed contrast angles of 45˚-55˚, while the contaminated samples had smaller spectral contact angles of 40° in the uncontaminated region. The laminate contaminated region exhibited contact angles of < 25°. To the best of our knowledge, this is the first report to demonstrate that hyperspectral imaging can be used to detect DMMP on building materials, with detection levels similar to c

Modified microwave method for the synthesis of visible light-responsive TiO2/MWCNTs nanocatalysts

PubMed Central

2013-01-01

Recently, TiO2/multi-walled carbon nanotube (MWCNT) hybrid nanocatalysts have been a subject of high interest due to their excellent structures, large surface areas and peculiar optical properties, which enhance their photocatalytic performance. In this work, a modified microwave technique was used to rapidly synthesise a TiO2/MWCNT nanocatalyst with a large surface area. X-ray powder diffraction, field-emission scanning electron microscopy, transmission electron microscopy and Brunauer-Emmett-Teller measurements were used to characterise the structure, morphology and the surface area of the sample. The photocatalytic activity of the hybrid nanocatalysts was evaluated through a comparison of the degradation of methylene blue dye under irradiation with ultraviolet and visible light. The results showed that the TiO2/MWCNT hybrid nanocatalysts degraded 34.9% of the methylene blue (MB) under irradiation with ultraviolet light, whereas 96.3% of the MB was degraded under irradiation with visible light. PMID:23919496

Extensive population admixture on drone congregation areas of the giant honeybee, Apis dorsata (Fabricius, 1793).

PubMed

Beaurepaire, Alexis L; Kraus, Bernard F; Koeniger, Gudrun; Koeniger, Nikolaus; Lim, Herbert; Moritz, Robin F A

2014-12-01

The giant honeybee Apis dorsata often forms dense colony aggregations which can include up to 200 often closely related nests in the same location, setting the stage for inbred matings. Yet, like in all other Apis species, A. dorsata queens mate in mid-air on lek like drone congregation areas (DCAs) where large numbers of males gather in flight. We here report how the drone composition of A. dorsata DCAs facilitates outbreeding, taking into the account both spatial (three DCAs) and temporal (subsequent sampling days) dynamics. We compared the drones' genotypes at ten microsatellite DNA markers with those of the queen genotypes of six drone-producing colonies located close to the DCAs (Tenom, Sabah, Malaysia). None of 430 sampled drones originated from any of these nearby colonies. Moreover, we estimated that 141 unidentified colonies were contributing to the three DCAs. Most of these colonies were participating multiple times in the different locations and/or during the consecutive days of sampling. The drones sampled in the DCAs could be attributed to six subpopulations. These were all admixed in all DCA samples, increasing the effective population size an order of magnitude and preventing matings between potentially related queens and drones.

Extensive population admixture on drone congregation areas of the giant honeybee, Apis dorsata (Fabricius, 1793)

PubMed Central

Beaurepaire, Alexis L; Kraus, Bernard F; Koeniger, Gudrun; Koeniger, Nikolaus; Lim, Herbert; Moritz, Robin F A

2014-01-01

The giant honeybee Apis dorsata often forms dense colony aggregations which can include up to 200 often closely related nests in the same location, setting the stage for inbred matings. Yet, like in all other Apis species, A. dorsata queens mate in mid-air on lek like drone congregation areas (DCAs) where large numbers of males gather in flight. We here report how the drone composition of A. dorsata DCAs facilitates outbreeding, taking into the account both spatial (three DCAs) and temporal (subsequent sampling days) dynamics. We compared the drones’ genotypes at ten microsatellite DNA markers with those of the queen genotypes of six drone-producing colonies located close to the DCAs (Tenom, Sabah, Malaysia). None of 430 sampled drones originated from any of these nearby colonies. Moreover, we estimated that 141 unidentified colonies were contributing to the three DCAs. Most of these colonies were participating multiple times in the different locations and/or during the consecutive days of sampling. The drones sampled in the DCAs could be attributed to six subpopulations. These were all admixed in all DCA samples, increasing the effective population size an order of magnitude and preventing matings between potentially related queens and drones. PMID:25558361

Soil quality of a degraded urban area

NASA Astrophysics Data System (ADS)

Panico, Speranza; Memoli, Valeria; Maisto, Giulia; De Marco, Anna

2017-04-01

Human activities cause modifications of the soil characteristics, leading to a significant reduction of the soil fertility and quality. The aim of this study was to evaluate the relationships between microbial activity or biomass and chemical characteristics (i.e. heavy metal and organic matter contents) of a degraded urban soil. The study area is located in an urban park (about 10 ha, called Quarantena) near to the Fusaro Lake of Campi Flegrei (Southern Italy); the Park was established in 1953 to shelter animals coming from any place of the Planet and execute veterinary checks before their delivery to different European zoos. In 1997, the park was abandoned and nowadays in it a large amount of urban wastes accumulates. Surface soils (0-10 cm) were sampled at three points: two of them covered by Holm Oak specimens (P1 and P2) and one covered by herbaceous species, particularly legumes (P3). P1 was localized at the border of the park and next to a busy road; P2 at the centre of the Quarantena Park; P3 at a gap area near the Fusaro Lake. The results showed that the soil sampled at P1 showed the highest Cr and Ni concentrations; the soil sampled at P3 had high levels of Cu and Pb, exceeding the threshold values of 100 µg g-1 d.w. fixed by the Italian law for urban soils, probably due to boat traffic, fishing practice and agricultural activities; the soil sampled at P2 had intermediate values of metal concentrations but the highest amount of organic matter (more than 20% d.w.). Despite of metal contamination, P1 and P3 showed higher soil microbial biomass and activity as compared to P2. Therefore, at this site, the organic matter accumulation could be due to the scarce litter degradation. In conclusion, although the studied area was not too large, a wide heterogeneity of soil quality (in terms of the investigated chemical and biological characteristics) was detected, depending on the local human impact.

Quantitative analysis of ions in spring water in three different areas of Hyogo Prefecture in Japan by far ultraviolet spectroscopy.

PubMed

Mitsuoka, Motoki; Shinzawa, Hideyuki; Morisawa, Yusuke; Kariyama, Naomi; Higashi, Noboru; Tsuboi, Motohiro; Ozaki, Yukihiro

2011-01-01

Far-ultraviolet (FUV) spectra in the 190-300 nm region were measured for spring water in Awaji-Akashi area, Tamba area and Rokko-Arima area in Hyogo Prefecture, Japan, these areas have quite different geology features. The spectra of the spring water in the Awaji-Akashi area can be divided into two groups: the spring water samples containing large amounts of NO(3)(-) and/or Cl(-), and those containing only small amounts of NO(3)(-) and Cl(-). The former shows a saturated band below 190 nm due to NO(3)(-) and/or Cl(-). These two types of spectra correspond to different lithological areas: sedimentary lithology near the sea shore containing many ions in the seawater and gravitic lithology far from the sea side, in the Awaji-Akashi area. The spring water from the Tamba area, which is far from the sea, contains relatively small amounts of NO(3)(-) and Cl(-); it does not yield a strong band in the region observed. The FUV spectra of three of four kinds of spring water samples in the Arima Hotspring show characteristic spectral patterns. They are quite different from the spectra of the spring water samples of the Rokko area. Calibration models were developed for NO(3)(-), Cl(-), SO(4)(2-), Na(+), and Mg(2+) in the nine kinds of spring water collected in the Awaji-Akashi area, Tamba, and Rokko-Arima area by using univariate analysis of the first derivative spectra and the actual values obtained by ion chromatography. NO(3)(-) yields the best results: correlation coefficient of 0.999 and standard deviation of 0.09 ppm with the wavelength of 212 nm. Cl(-) also gives good results: correlation coefficient of 0.993 and standard deviation of 0.5 ppm with the wavelength of 192 nm.

Effects of surface applications of biosolids on groundwater quality and trace-element concentrations in crops near Deer Trail, Colorado, 2004-2010

USGS Publications Warehouse

Yager, Tracy J.B.; Crock, James G.; Smith, David B.; Furlong, Edward T.; Hageman, Philip L.; Foreman, William T.; Gray, James L.; ReVello, Rhiannon C.

2013-01-01

The U.S. Geological Survey (USGS), in cooperation with Metro Wastewater Reclamation District (Metro District), studied biosolids composition and the effects of biosolids applications on groundwater quality and trace-element concentrations in crops of the Metro District properties near Deer Trail, Colorado, during 2004 through 2010. Priority parameters for each monitoring component included the nine trace elements regulated by Colorado for biosolids (arsenic, cadmium, copper, lead, mercury, molybdenum, nickel, selenium, and zinc); other constituents also were analyzed. All concentrations for the priority parameters in monthly biosolids samples were less than Colorado regulatory limits, and the concentrations were relatively consistent. Biosolids likely were the largest source of nitrogen and phosphorus on the Metro District properties. Plutonium isotopes were not detected in the biosolids, but many organic wastewater compounds (organic wastewater compounds: wastewater indicators, pharmaceuticals, and hormones) were detected in substantial concentrations relative to minimum reporting levels and various surface-water concentrations. Bismuth, copper, mercury, nitrogen, phosphorus, silver, biogenic sterols, detergent degradates, disinfectants, fire retardants, fragrances, pharmaceuticals, and plasticizers would be the most likely biosolids signature to indicate the presence of Metro District biosolids in soil or streambed sediment from the study area. Antimony, cadmium, cobalt, copper, molybdenum, nickel, nitrogen, phosphorus, selenium, tungsten, vanadium, zinc, detergent degradates, disinfectants, fire retardants, fragrances, pharmaceuticals or their degradates, and plasticizers would be the most likely biosolids signature for groundwater and surface water in the study area. More biosolids-signature components detected and larger concentration differences from untreated materials, baseline, and blank samples indicate more evidence of biosolids presence or effects. Although the inorganic constituent concentrations were relatively large in samples from one monitoring well, the concentrations of organic wastewater compounds in groundwater samples were not correspondingly large. Concentrations of organic wastewater compounds in the groundwater samples from all five monitoring wells were less than the minimum reporting levels with only a few detections. Some of the organic wastewater compounds detected could have anthropogenic sources that are not biosolids. Concentrations of priority parameters in groundwater varied spatially and temporally but generally were less than Colorado regulatory limits. Concentrations of dissolved nitrate, arsenic, and selenium, in addition to chloride, sulfate, total dissolved solids, boron, iron, manganese, and uranium, in samples from some wells exceeded the Colorado standards. Concentrations of dissolved nitrate (three wells), molybdenum (one well), selenium (two wells), and uranium (one well) in shallow groundwater had significant (alpha = 0.05) upward trends in some parts of the study area. The biosolids-signature results indicate that the aquifers intercepted by the five routinely sampled wells likely have received some recharge through treated (biosolids-applied) fields or biosolids-affected ponds. Adverse effects from this biosolids-related recharge range from few (if any) at one well to large and significantly (alpha = 0.05) increasing nitrate concentrations at another well. A statistical evaluation of five paired wheat-grain samples from treated (biosolids-applied) fields and untreated (control) fields did not indicate any evidence that biosolids applications significantly (alpha = 0.05 or 0.10) increased concentration of any of these constituents in wheat grain. The wheat-grain concentrations from this study were similar to those from other studies for fields in North America where no biosolids were applied. The data for the limited crop samples indicate that biosolids applications are not increasing the concentrations of arsenic, cadmium, copper, lead, mercury, molybdenum, nickel, selenium, sulfur, and zinc in mature wheat grain from the study area.

Sampling procedures for throughfall monitoring: A simulation study

NASA Astrophysics Data System (ADS)

Zimmermann, Beate; Zimmermann, Alexander; Lark, Richard Murray; Elsenbeer, Helmut

2010-01-01

What is the most appropriate sampling scheme to estimate event-based average throughfall? A satisfactory answer to this seemingly simple question has yet to be found, a failure which we attribute to previous efforts' dependence on empirical studies. Here we try to answer this question by simulating stochastic throughfall fields based on parameters for statistical models of large monitoring data sets. We subsequently sampled these fields with different sampling designs and variable sample supports. We evaluated the performance of a particular sampling scheme with respect to the uncertainty of possible estimated means of throughfall volumes. Even for a relative error limit of 20%, an impractically large number of small, funnel-type collectors would be required to estimate mean throughfall, particularly for small events. While stratification of the target area is not superior to simple random sampling, cluster random sampling involves the risk of being less efficient. A larger sample support, e.g., the use of trough-type collectors, considerably reduces the necessary sample sizes and eliminates the sensitivity of the mean to outliers. Since the gain in time associated with the manual handling of troughs versus funnels depends on the local precipitation regime, the employment of automatically recording clusters of long troughs emerges as the most promising sampling scheme. Even so, a relative error of less than 5% appears out of reach for throughfall under heterogeneous canopies. We therefore suspect a considerable uncertainty of input parameters for interception models derived from measured throughfall, in particular, for those requiring data of small throughfall events.

Analysis and imaging of biocidal agrochemicals using ToF-SIMS.

PubMed

Converso, Valerio; Fearn, Sarah; Ware, Ecaterina; McPhail, David S; Flemming, Anthony J; Bundy, Jacob G

2017-09-06

ToF-SIMS has been increasingly widely used in recent years to look at biological matrices, in particular for biomedical research, although there is still a lot of development needed to maximise the value of this technique in the life sciences. The main issue for biological matrices is the complexity of the mass spectra and therefore the difficulty to specifically and precisely detect analytes in the biological sample. Here we evaluated the use of ToF-SIMS in the agrochemical field, which remains a largely unexplored area for this technique. We profiled a large number of biocidal active ingredients (herbicides, fungicides, and insecticides); we then selected fludioxonil, a halogenated fungicide, as a model compound for more detailed study, including the effect of co-occurring biomolecules on detection limits. There was a wide range of sensitivity of the ToF-SIMS for the different active ingredient compounds, but fludioxonil was readily detected in real-world samples (wheat seeds coated with a commercial formulation). Fludioxonil did not penetrate the seed to any great depth, but was largely restricted to a layer coating the seed surface. ToF-SIMS has clear potential as a tool for not only detecting biocides in biological samples, but also mapping their distribution.

Fish abundances in shoreline habitats and submerged aquatic vegetation in a tidal freshwater embayment of the Potomac River.

PubMed

Kraus, Richard T; Jones, R Christian

2012-05-01

Submerged aquatic vegetation (SAV) is considered an important habitat for juvenile and small forage fish species, but many long-term recruitment surveys do not effectively monitor fish communities in SAV. To better understand the impact of recent large increases of SAV on the fish community in tidal freshwater reaches of the Potomac River, we compared traditional seine sampling from shore with drop ring sampling of SAV beds (primarily Hydrilla) in a shallow water (depths, <1.5 m) embayment, Gunston Cove. To accomplish this, we developed species-specific catch efficiency values for the seine gear and calculated area-based density in both shoreline and SAV habitats in late summer of three different years (2007, 2008, and 2009). For the dominant species (Fundulus diaphanus, Lepomis macrochirus, Etheostoma olmstedi, Morone americana, Lepomis gibbosus, and Fundulus heteroclitus), density was nearly always higher in SAV, but overall, species richness was highest in shoreline habitats sampled with seines. Although historical monitoring of fish in Gunston Cove (and throughout Chesapeake Bay) is based upon seine sampling (and trawl sampling in deeper areas), the high densities of fish and larger areal extent of SAV indicated that complementary sampling of SAV habitats would produce more accurate trends in abundances of common species. Because drop ring samples cover much less area than seines and may miss rare species, a combination of methods that includes seine sampling is needed for biodiversity assessment. The resurgence of SAV in tidal freshwater signifies improving water quality, and methods we evaluated here support improved inferences about population trends and fish community structure as indicators of ecosystem condition.

Alpine Grassland Soil Organic Carbon Stock and Its Uncertainty in the Three Rivers Source Region of the Tibetan Plateau

PubMed Central

Chang, Xiaofeng; Wang, Shiping; Cui, Shujuan; Zhu, Xiaoxue; Luo, Caiyun; Zhang, Zhenhua; Wilkes, Andreas

2014-01-01

Alpine grassland of the Tibetan Plateau is an important component of global soil organic carbon (SOC) stocks, but insufficient field observations and large spatial heterogeneity leads to great uncertainty in their estimation. In the Three Rivers Source Region (TRSR), alpine grasslands account for more than 75% of the total area. However, the regional carbon (C) stock estimate and their uncertainty have seldom been tested. Here we quantified the regional SOC stock and its uncertainty using 298 soil profiles surveyed from 35 sites across the TRSR during 2006–2008. We showed that the upper soil (0–30 cm depth) in alpine grasslands of the TRSR stores 2.03 Pg C, with a 95% confidence interval ranging from 1.25 to 2.81 Pg C. Alpine meadow soils comprised 73% (i.e. 1.48 Pg C) of the regional SOC estimate, but had the greatest uncertainty at 51%. The statistical power to detect a deviation of 10% uncertainty in grassland C stock was less than 0.50. The required sample size to detect this deviation at a power of 90% was about 6–7 times more than the number of sample sites surveyed. Comparison of our observed SOC density with the corresponding values from the dataset of Yang et al. indicates that these two datasets are comparable. The combined dataset did not reduce the uncertainty in the estimate of the regional grassland soil C stock. This result could be mainly explained by the underrepresentation of sampling sites in large areas with poor accessibility. Further research to improve the regional SOC stock estimate should optimize sampling strategy by considering the number of samples and their spatial distribution. PMID:24819054

Thyroid hormones and thyroid disease in relation to perchlorate dose and residence near a superfund site.

PubMed

Gold, Ellen B; Blount, Benjamin C; O'Neill Rasor, Marianne; Lee, Jennifer S; Alwis, Udeni; Srivastav, Anup; Kim, Kyoungmi

2013-07-01

Perchlorate is a widely occurring contaminant, which can competitively inhibit iodide uptake and thus thyroid hormone production. The health effects of chronic low dose perchlorate exposure are largely unknown. In a community-based study, we compared thyroid function and disease in women with differing likelihoods of prior and current perchlorate exposure. Residential blocks were randomly selected from areas: (1) with potential perchlorate exposure via drinking water; (2) with potential exposure to environmental contaminants; and (3) neighboring but without such exposures. Eligibility included having lived in the area for ≥6 months and aged 20-50 years during 1988-1996 (during documented drinking water well contamination). We interviewed 814 women and collected blood samples (assayed for thyroid stimulating hormone and free thyroxine) from 431 interviewed women. Daily urine samples were assayed for perchlorate and iodide for 178 premenopausal women with blood samples. We performed multivariable regression analyses comparing thyroid function and disease by residential area and by urinary perchlorate dose adjusted for urinary iodide levels. Residential location and current perchlorate dose were not associated with thyroid function or disease. No persistent effect of perchlorate on thyroid function or disease was found several years after contaminated wells were capped.

Mapping Secondary Forest Succession on Abandoned Agricultural Land in the Polish Carpathians

NASA Astrophysics Data System (ADS)

Kolecka, N.; Kozak, J.; Kaim, D.; Dobosz, M.; Ginzler, Ch.; Psomas, A.

2016-06-01

Land abandonment and secondary forest succession have played a significant role in land cover changes and forest cover increase in mountain areas in Europe over the past several decades. Land abandonment can be easily observed in the field over small areas, but it is difficult to map over the large areas, e.g., with remote sensing, due to its subtle and spatially dispersed character. Our previous paper presented how the LiDAR (Light Detection and Ranging) and topographic data were used to detect secondary forest succession on abandoned land in one commune located in the Polish Carpathians by means of object-based image analysis (OBIA) and GIS (Kolecka et al., 2015). This paper proposes how the method can be applied to efficiently map secondary forest succession over the entire Polish Carpathians, incorporating spatial sampling strategy supported by various ancillary data. Here we discuss the methods of spatial sampling, its limitations and results in the context of future secondary forest succession modelling.

Evaluation of drinking quality of groundwater through multivariate techniques in urban area.

PubMed

Das, Madhumita; Kumar, A; Mohapatra, M; Muduli, S D

2010-07-01

Groundwater is a major source of drinking water in urban areas. Because of the growing threat of debasing water quality due to urbanization and development, monitoring water quality is a prerequisite to ensure its suitability for use in drinking. But analysis of a large number of properties and parameter to parameter basis evaluation of water quality is not feasible in a regular interval. Multivariate techniques could streamline the data without much loss of information to a reasonably manageable data set. In this study, using principal component analysis, 11 relevant properties of 58 water samples were grouped into three statistical factors. Discriminant analysis identified "pH influence" as the most distinguished factor and pH, Fe, and NO₃⁻ as the most discriminating variables and could be treated as water quality indicators. These were utilized to classify the sampling sites into homogeneous clusters that reflect location-wise importance of specific indicator/s for use to monitor drinking water quality in the whole study area.

Metallic elements and isotope of Pb in wet precipitation in urban area, South America

NASA Astrophysics Data System (ADS)

Migliavacca, Daniela Montanari; Teixeira, Elba Calesso; Gervasoni, Fernanda; Conceição, Rommulo Vieira; Raya Rodriguez, Maria Teresa

2012-04-01

The atmosphere of urban areas has been the subject of many studies to show the atmospheric pollution in large urban centers. By quantifying wet precipitation through the analysis of metallic elements (ICP/AES) and Pb isotopes, the wet precipitation of the Metropolitan Area of the Porto Alegre (MAPA), Brazil, was characterized. The samples were collected between July 2005 and December 2007. Zn, Fe and Mn showed the highest concentration in studied sites. Sapucaia do Sul showed the highest average for Zn, due to influence by the steel plant located near the sampling site. The contribution of anthropogenic emissions from vehicular activity and steel plants in wet precipitation and suspended particulate matter in the MAPA was identified by the isotopic signatures of 208Pb/207Pb and 206Pb/207Pb. Moreover the analyses of the metallic elements allowed also to identify the contribution of other anthropic sources, such as steel plants and oil refinery.

Identifying Minefields and Verifying Clearance: Adapting Statistical Methods for UXO Target Detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilbert, Richard O.; O'Brien, Robert F.; Wilson, John E.

2003-09-01

It may not be feasible to completely survey large tracts of land suspected of containing minefields. It is desirable to develop a characterization protocol that will confidently identify minefields within these large land tracts if they exist. Naturally, surveying areas of greatest concern and most likely locations would be necessary but will not provide the needed confidence that an unknown minefield had not eluded detection. Once minefields are detected, methods are needed to bound the area that will require detailed mine detection surveys. The US Department of Defense Strategic Environmental Research and Development Program (SERDP) is sponsoring the development ofmore » statistical survey methods and tools for detecting potential UXO targets. These methods may be directly applicable to demining efforts. Statistical methods are employed to determine the optimal geophysical survey transect spacing to have confidence of detecting target areas of a critical size, shape, and anomaly density. Other methods under development determine the proportion of a land area that must be surveyed to confidently conclude that there are no UXO present. Adaptive sampling schemes are also being developed as an approach for bounding the target areas. These methods and tools will be presented and the status of relevant research in this area will be discussed.« less

Role of a large marine protected area for conserving landscape attributes of sand habitats on Georges Bank (NW Atlantic)

USGS Publications Warehouse

Lindholm, J.; Auster, P.; Valentine, P.

2004-01-01

Mobile fishing gear reduces seafloor habitat complexity through the removal of structure-building fauna, e.g. emergent organisms that create pits and burrows, as well as by smoothing of sedimentary bedforms (e.g. sand ripples). In this study, we compared the relative abundance of microhabitat features (the scale at which individual fish associate with seafloor habitat) inside and outside of a large fishery closed area (6917 km2) on Georges Bank. Starting in late 1994, the closed area excluded all bottom tending fishing gear capable of capturing demersal fishes. A total of 32 stations were selected inside and outside of the closed area in sand habitats. Video and still photographic transects were conducted at each station using the Seabed Observation and Sampling System (SEABOSS). Seven common (i.e. featureless sand, rippled sand, sand with emergent fauna, bare gravelly sand, gravelly sand with attached-erect fauna, whole shell, shell fragment) and 2 rare (sponges, biogenic depressions) microhabitat types were compared separately. Results showed significant differences in the relative abundance of the shell fragment and sponge microhabitat types between fished and unfished areas. The lack of differences for the other microhabitats may indicate that the level of fishing activity in the area is matched by the system's ability to recover.

Sunda epicontinental shelf and Quaternary glacial-interglacial sea level variation and their implications to the regional and global environmental change

NASA Astrophysics Data System (ADS)

Soepri Hantoro, Wahyoe

2018-02-01

Sunda Epicontinental Shelf occupies a large area between Asia and Indonesian Maritime Continent. This shallow shelf developed soon as stability of this area since Pliocene was achieved. Sedimentation and erosion started, following sea level variation of Milankovitch cycle that changed this area to, partly to entirely become a low lying open land. These changes imply a difference height of about 135 m sea level. Consequence of this changes from shallow sea during interglacial to the exposed low land during glacial period is producing different land cover that might influence to the surrounding area. As the large land surface, this area should be covered by low land tropical forest, savanna to wet coastal plain. This large low-lying land belongs an important river drainage system of South East Asia in the north (Gulf of Thailand) and another system that curved from Malay Peninsula, Sumatra, Bangka-Belitung and Kalimantan, named as Palaeo Sunda River. The total area of this land is about 1 million km2, this must bring consequences to the environmental condition. This change belongs to the global change on which the signal may be sent to a distance, then is preserved as geological formation. Being large and flat land, it has a long and winding river valley so this land influences the life of biota as fauna and flora but also human being that may live or just move on the passing through around East Asia. Global sea level changes through time which is then followed by the change of the area of land or water have indeed influenced the hydrology and carbon cycle balance. Through studying the stratigraphy and geology dynamic, based on seismic images and core samples from drilling work, one can be obtained, the better understanding the environmental change and its impact to the regional but could be global scale.

Fabric changes and their influence on P-wave velocity patterns—examples from a polyphase deformed orthogneiss

NASA Astrophysics Data System (ADS)

Siegesmund, S.; Vollbrecht, A.; Pros, Z.

1993-10-01

The complete P-wave velocity distribution, preferred orientation of rock-forming minerals and microcracks of two differently deformed orthogneisses from the Kutna Hora Crystalline Unit were investigated. The complete symmetry of P-wave velocities were determined as a function of confining pressure on the basis of 132 independent propagation directions up to 400 MPa. The two samples are of almost identical mineralogical composition, but exhibit different fabrics which can be related to different positions within a large-scale fold structure. The symmetry of the Vp-diagrams change from nearly transversely isotropic for the sample from the limb area to orthorhombic for the sample from the hinge zone, which shows an additional crenulation cleavage. This change of symmetry is observed at all pressure levels. Reorientation of the main velocity directions ( Vpmin, Vpmax, Kpint) between hinge and limb is controlled by the microcrack fabric and the texture of the rock-forming minerals. This can cause significant differences in reflectivity related to fabric changes within large-scale folds.

Trace element distribution in the snow cover from an urban area in central Poland.

PubMed

Siudek, Patrycja; Frankowski, Marcin; Siepak, Jerzy

2015-05-01

This work presents the first results from winter field campaigns focusing on trace metals and metalloid chemistry in the snow cover from an urbanized region in central Poland. Samples were collected between January and March 2013 and trace element concentrations were determined using GF-AAS. A large inter-seasonal variability depending on anthropogenic emission, depositional processes, and meteorological conditions was observed. The highest concentration (in μg L(-1)) was reported for Pb (34.90), followed by Ni (31.37), Zn (31.00), Cu (13.71), Cr (2.36), As (1.58), and Cd (0.25). In addition, several major anthropogenic sources were identified based on principal component analysis (PCA), among which the most significant was the activity of industry and coal combustion for residential heating. It was stated that elevated concentrations of some trace metals in snow samples were associated with frequent occurrence of south and southeast advection of highly polluted air masses toward the sampling site, suggesting a large impact of regional urban/industrial pollution plumes.

Mobility of plume-derived volcanogenic elements in meteoric water at Nyiragongo volcano (Congo) inferred from the chemical composition of single rainfall events

NASA Astrophysics Data System (ADS)

Liotta, Marcello; Shamavu, Patient; Scaglione, Sarah; D'Alessandro, Walter; Bobrowski, Nicole; Bruno Giuffrida, Giovanni; Tedesco, Dario; Calabrese, Sergio

2017-11-01

The chemical composition of single rainfall events was investigated at Nyiragongo volcano (Democratic Republic of Congo) with the aim of determining the relative contributions of plume-derived elements. The different locations of the sampling sites allowed both plume-affected samples (hereafter referred to as ;fumigated samples;) and samples representative of the local background to be collected. The chemical composition of the local background reflects the peculiar geographic features of the area, being influenced by biomass burning, geogenic dust, and biological activity. Conversely, fumigated samples contain large amounts of volcanogenic elements that can be clearly distinguished from the local background. These elements are released into the atmosphere from the persistently boiling lava lake of the Nyiragongo crater and from the neonate lava lake of Nyamulagira. These emissions result in a volcanic plume that includes solid particles, acidic droplets, and gaseous species. The chemical signature of the volcanic emissions appears in falling raindrops as they interact with the plume. HCl and HBr readily dissolve in water, and so their ratio in rain samples reflects that of the volcanic plume. The transport of HF is mediated by the large amount of silicate particles generated at the magma-air interface. SO2 is partially converted into SO42- that dissolves in water. The refractory elements dissolved in rain samples derive from the dissolution of silicate particles, and most of them (Al, Mg, Ca, and Sr) are present at exactly the same molar ratios as in the rocks. In contrast, elements such as Na, K, Rb, Cu, and Pb are enriched relative to the whole-rock composition, suggesting that they are volatilized during magma degassing. After correcting for the dissolution of silicate particles, we can define that the volatility of the elements decreases in the following order: Pb ≫ Rb > K > Na. This finding, which is the first for a volcanic plume, is consistent with previous measurements in high-temperature fumaroles at other volcanic areas.

Metallographic Characterization of Wrought Depleted Uranium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Forsyth, Robert Thomas; Hill, Mary Ann

Metallographic characterization was performed on wrought depleted uranium (DU) samples taken from the longitudinal and transverse orientations from specific locations on two specimens. Characterization of the samples included general microstructure, inclusion analysis, grain size analysis, and microhardness testing. Comparisons of the characterization results were made to determine any differences based on specimen, sample orientation, or sample location. In addition, the characterization results for the wrought DU samples were also compared with data obtained from the metallographic characterization of cast DU samples previously characterized. No differences were observed in microstructure, inclusion size, morphology, and distribution, or grain size in regard tomore » specimen, location, or orientation for the wrought depleted uranium samples. However, a small difference was observed in average hardness with regard to orientation at the same locations within the same specimen. The longitudinal samples were slightly harder than the transverse samples from the same location of the same specimen. This was true for both wrought DU specimens. Comparing the wrought DU sample data with the previously characterized cast DU sample data, distinct differences in microstructure, inclusion size, morphology and distribution, grain size, and microhardness were observed. As expected, the microstructure of the wrought DU samples consisted of small recrystallized grains which were uniform, randomly oriented, and equiaxed with minimal twinning observed in only a few grains. In contrast, the cast DU microstructure consisted of large irregularly shaped grains with extensive twinning observed in most grains. Inclusions in the wrought DU samples were elongated, broken and cracked and light and dark phases were observed in some inclusions. The mean inclusion area percentage for the wrought DU samples ranged from 0.08% to 0.34% and the average density from all wrought DU samples was 1.62E+04/cm 2. Inclusions in the cast DU samples were equiaxed and intact with light and dark phases observed in some inclusions. The mean inclusion area percentage for the cast DU samples ranged from 0.93% to 1.00% and the average density from all wrought DU samples was 2.83E+04/cm 2. The average mean grain area from all wrought DU samples was 141 μm 2 while the average mean grain area from all cast DU samples was 1.7 mm2. The average Knoop microhardness from all wrought DU samples was 215 HK and the average Knoop microhardness from all cast DU samples was 264 HK.« less

Comparison of nitrate, pesticides, and volatile organic compounds in samples from monitoring and public-supply wells, Kirkwood-Cohansey aquifer system, southern New Jersey

USGS Publications Warehouse

Stackelberg, Paul E.; Kauffman, L.J.; Baehr, A.L.; Ayers, M.A.

2000-01-01

The number and total concentration of volatile organic compounds (VOCs) per sample were significantly greater in water from public-supply wells than in water from shallow and moderate-depth monitoring wells in the surficial Kirkwood-Cohansey aquifer system in the Glassboro area of southern New Jersey. In contrast, concentrations of nitrate (as nitrogen) and the number and total concentration of pesticides per sample were statistically similar in samples from shallow and moderate-depth monitoring wells and those from public-supply wells. VOCs in ground water typically are derived from point sources, which commonly exist in urban areas and which result in spatially variable contaminant concentrations near the water table. Because larger volumes of water are withdrawn from public-supply wells than from monitoring wells, their contributing areas are larger and, therefore, they are more likely to intercept water flowing from VOC point sources. Additionally, public-supply wells intercept flow paths that span a large temporal interval. Public-supply wells in the Glassboro study area withdraw water flowing along short paths, which contains VOCs that recently entered the aquifer system, and water flowing along relatively long paths, which contains VOCs that originated from the degradation of parent compounds or that are associated with past land uses. Because the volume of water withdrawn from monitoring wells is small and because shallow monitoring wells are screened near the water table, they generally intercept only relatively short flow paths. Therefore, samples from these wells represent relatively recent, discrete time intervals and contain both fewer VOCs and a lower total VOC concentration than samples from public-supply wells. Nitrate and pesticides in ground water typically are derived from nonpoint sources, which commonly are found in both agricultural and urban areas and typically result in lowlevel, relatively uniform concentrations near the water table. Because nonpoint sources are diffuse and because processes such as degradation or sorption/dispersion do not occur at rates sufficient to prevent detection of these constituents in parts of the aquifer used for domestic and public supply in the study area, concentrations of nitrate and pesticides and numbers of pesticide compounds are likely to be similar in samples from shallow monitoring wells and samples from public-supply wells. Results of a comparison of (1) the general characteristics of, and water-quality data from, public-supply wells in the Glassboro study area to available data from public-supply wells screened in the Kirkwood-Cohansey aquifer system outside the study area, and (2) land-use settings, soil characteristics, and aquifer properties in and outside the study area indicate that the findings of this study likely are applicable to the entire extent of the Kirkwood- Cohansey aquifer system in southern New Jersey.

Effects of exchanged cation on the microporosity of montmorillonite

USGS Publications Warehouse

Rutherford, David W.; Chiou, Cary T.; Eberl, Dennis D.

1997-01-01

The micropore volumes of 2 montmorillonites (SAz-1 and SWy-1), each exchanged with Ca, Na, K, Cs and tetramethylammonium (TMA) ions, were calculated from the measured vapor adsorption data of N2 and neo-hexane by use of t- and αs-plots. The corresponding surface areas of the exchanged clays were determined from Brunauer-Emmett-Teller (BET) plots of N2 adsorption data. Micropore volumes and surface areas of the samples increased with the size of exchanged cation: TMA > Cs > K > Ca > Na. The SAz-1 exchanged clays showed generally greater micropore volumes and surface areas than the corresponding SWy-1 clays. The vapor adsorption data and d(001) measurements for dry clay samples were used together to evaluate the likely locations and accessibility of clay micropores, especially the relative accessibility of their interlayer spacing. For both source clays exchanged with Na, Ca and K ions, the interlayer spacing appeared to be too small to admit nonpolar gases and the accessible micropores appeared to have dimensions greater than 5.0 Å, the limiting molecular dimension of neo-hexane. In these systems, there was a good consistency of micropore volumes detected by N2 and neo-hexane. When the clays were intercalated with relatively large cations (TMA and possibly Cs), the large layer expansion created additional microporosity, which was more readily accessible to small N2 than to relatively large neo-hexane. Hence, the micropore volume as detected by N2 was greater than that detected by neo-hexane. The micropore volumes with pore dimensions greater than 5 Å determined for clays exchanged with Na, Ca and K likely resulted from the pores on particle edges and void created by overlap regions of layers. The increase in micropore volumes with pore dimensions less than 5 Å determined for clays exchanged with TMA and possibly Cs could be caused by opening of the interlayer region by the intercalation of these large cations.

Diversity, distribution and population size structure of deep Mediterranean gorgonian assemblages (Menorca Channel, Western Mediterranean Sea)

NASA Astrophysics Data System (ADS)

Grinyó, Jordi; Gori, Andrea; Ambroso, Stefano; Purroy, Ariadna; Calatayud, Clara; Dominguez-Carrió, Carlos; Coppari, Martina; Lo Iacono, Claudio; López-González, Pablo J.; Gili, Josep-Maria

2016-06-01

Gorgonians are a key group of organisms in benthic marine communities with a wide bathymetric and geographical distribution. Although their presence on continental shelves and slopes has been known for more than 100 years, knowledge concerning the ecology of deep gorgonian species is still in a very preliminary stage. To overcome this situation, gorgonian assemblages located at 40-360 m depth were studied over a large geographical area on the continental shelf and upper slope of the Menorca Channel (Western Mediterranean Sea). A quantitative analysis of video transects recorded by a manned submersible and a remotely operated vehicle, were used to examine the diversity, distribution and demography of gorgonian species. Results showed high gorgonian diversity within this depth range (a total of nine species were observed) compared to Mediterranean coastal areas. Gorgonian assemblages on the continental shelf and upper slope were mostly monospecific (respectively 73% and 76% of occupied sampling units contained one single species), whereas shelf edge assemblages were highly multispecific (92% of occupied sampling units contained several species). This contrasts with the monospecificity of Mediterranean coastal gorgonian assemblages. Gorgonian populations on the continental shelf were mostly dominated by small colonies (88% of measured colonies) with few intermediate and large colonies (12% of measured colonies). In deeper areas small colonies were still dominant (60% of measured colonies), but intermediate and large colonies were much more abundant (40% of measured colonies). This suggests high recruitment rates on the continental shelf, but perturbations (trammel nets, long lines and strong storms) may limit the presence of intermediate and large colonies. Conversely, on the shelf edge and upper slope a more stable environment may allow colonies to reach larger dimensions. The identification and ecological characterization of these deep assemblages further extends the current knowledge about Mediterranean gorgonians, and is fundamental in improving the management and conservation of deep benthic ecosystems.

An Improved Nested Sampling Algorithm for Model Selection and Assessment

NASA Astrophysics Data System (ADS)

Zeng, X.; Ye, M.; Wu, J.; WANG, D.

2017-12-01

Multimodel strategy is a general approach for treating model structure uncertainty in recent researches. The unknown groundwater system is represented by several plausible conceptual models. Each alternative conceptual model is attached with a weight which represents the possibility of this model. In Bayesian framework, the posterior model weight is computed as the product of model prior weight and marginal likelihood (or termed as model evidence). As a result, estimating marginal likelihoods is crucial for reliable model selection and assessment in multimodel analysis. Nested sampling estimator (NSE) is a new proposed algorithm for marginal likelihood estimation. The implementation of NSE comprises searching the parameters' space from low likelihood area to high likelihood area gradually, and this evolution is finished iteratively via local sampling procedure. Thus, the efficiency of NSE is dominated by the strength of local sampling procedure. Currently, Metropolis-Hasting (M-H) algorithm and its variants are often used for local sampling in NSE. However, M-H is not an efficient sampling algorithm for high-dimensional or complex likelihood function. For improving the performance of NSE, it could be feasible to integrate more efficient and elaborated sampling algorithm - DREAMzs into the local sampling. In addition, in order to overcome the computation burden problem of large quantity of repeating model executions in marginal likelihood estimation, an adaptive sparse grid stochastic collocation method is used to build the surrogates for original groundwater model.

Probing large-scale structure with large samples of X-ray selected AGN. I. Baryonic acoustic oscillations

NASA Astrophysics Data System (ADS)

Hütsi, Gert; Gilfanov, Marat; Kolodzig, Alexander; Sunyaev, Rashid

2014-12-01

We investigate the potential of large X-ray-selected AGN samples for detecting baryonic acoustic oscillations (BAO). Though AGN selection in X-ray band is very clean and efficient, it does not provide redshift information, and thus needs to be complemented with an optical follow-up. The main focus of this study is (i) to find the requirements needed for the quality of the optical follow-up and (ii) to formulate the optimal strategy of the X-ray survey, in order to detect the BAO. We demonstrate that redshift accuracy of σ0 = 10-2 at z = 1 and the catastrophic failure rate of ffail ≲ 30% are sufficient for a reliable detection of BAO in future X-ray surveys. Spectroscopic quality redshifts (σ0 = 10-3 and ffail ~ 0) will boost the confidence level of the BAO detection by a factor of ~2. For meaningful detection of BAO, X-ray surveys of moderate depth of Flim ~ few 10-15 erg s-1/cm2 covering sky area from a few hundred to ~ten thousand square degrees are required. The optimal strategy for the BAO detection does not necessarily require full sky coverage. For example, in a 1000 day-long survey by an eROSITA type telescope, an optimal strategy would be to survey a sky area of ~9000 deg2, yielding a ~16σ BAO detection. A similar detection will be achieved by ATHENA+ or WFXT class telescopes in a survey with a duration of 100 days, covering a similar sky area. XMM-Newton can achieve a marginal BAO detection in a 100-day survey covering ~400 deg2. These surveys would demand a moderate-to-high cost in terms the optical follow-ups, requiring determination of redshifts of ~105 (XMM-Newton) to ~3 × 106 objects (eROSITA, ATHENA+, and WFXT) in these sky areas.

Decoupling the Effects of High Crystallinity and Surface Area on the Photocatalytic Overall Water Splitting over β-Ga2 O3 Nanoparticles by Chemical Vapor Synthesis.

PubMed

Lukic, Sasa; Menze, Jasper; Weide, Philipp; Busser, G Wilma; Winterer, Markus; Muhler, Martin

2017-09-11

Chemical vapor synthesis (CVS) is a unique method to prepare well-defined photocatalyst materials with both large specific surface area and a high degree of crystallinity. The obtained β-Ga 2 O 3 nanoparticles were optimized for photocatalysis by reductive photodeposition of the Rh/CrO x co-catalyst system. The influence of the degree of crystallinity and the specific surface area on photocatalytic aqueous methanol reforming and overall water splitting (OWS) was investigated by synthesizing β-Ga 2 O 3 samples in the temperature range from 1000 °C to 1500 °C. With increasing temperature, the specific surface area and the microstrain were found to decrease, whereas the degree of crystallinity and the crystallite size increased. Whereas the photocatalyst with the highest specific surface area showed the highest aqueous methanol reforming activity, the highest OWS activity was that for the sample with an optimum ratio between high degree of crystallinity and specific surface area. Thus, it was possible to show that the facile aqueous methanol reforming and the demanding OWS have different requirements for high photocatalytic activity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Assessment of lead pollution in topsoils of a southern Italy area: Analysis of urban and peri-urban environment.

PubMed

Guagliardi, Ilaria; Cicchella, Domenico; De Rosa, Rosanna; Buttafuoco, Gabriele

2015-07-01

Exposure to lead (Pb) may affect adversely human health. Mapping soil Pb contents is essential to obtain a quantitative estimate of potential risk of Pb contamination. The main aim of this paper was to determine the soil Pb concentrations in the urban and peri-urban area of Cosenza-Rende to map their spatial distribution and assess the probability that soil Pb concentration exceeds a critical threshold that might cause concern for human health. Samples were collected at 149 locations from residual and non-residual topsoil in gardens, parks, flower-beds, and agricultural fields. Fine earth fraction of soil samples was analyzed by X-ray Fluorescence spectrometry. Stochastic images generated by the sequential Gaussian simulation were jointly combined to calculate the probability of exceeding the critical threshold that could be used to delineate the potentially risky areas. Results showed areas in which Pb concentration values were higher to the Italian regulatory values. These polluted areas were quite large and likely, they could create a significant health risk for human beings and vegetation in the near future. The results demonstrated that the proposed approach can be used to study soil contamination to produce geochemical maps, and identify hot-spot areas for soil Pb concentration. Copyright © 2015. Published by Elsevier B.V.

High resolution micro-CT of low attenuating organic materials using large area photon-counting detector

NASA Astrophysics Data System (ADS)

Kumpová, I.; Vavřík, D.; Fíla, T.; Koudelka, P.; Jandejsek, I.; Jakůbek, J.; Kytýř, D.; Zlámal, P.; Vopálenský, M.; Gantar, A.

2016-02-01

To overcome certain limitations of contemporary materials used for bone tissue engineering, such as inflammatory response after implantation, a whole new class of materials based on polysaccharide compounds is being developed. Here, nanoparticulate bioactive glass reinforced gelan-gum (GG-BAG) has recently been proposed for the production of bone scaffolds. This material offers promising biocompatibility properties, including bioactivity and biodegradability, with the possibility of producing scaffolds with directly controlled microgeometry. However, to utilize such a scaffold with application-optimized properties, large sets of complex numerical simulations using the real microgeometry of the material have to be carried out during the development process. Because the GG-BAG is a material with intrinsically very low attenuation to X-rays, its radiographical imaging, including tomographical scanning and reconstructions, with resolution required by numerical simulations might be a very challenging task. In this paper, we present a study on X-ray imaging of GG-BAG samples. High-resolution volumetric images of investigated specimens were generated on the basis of micro-CT measurements using a large area flat-panel detector and a large area photon-counting detector. The photon-counting detector was composed of a 010× 1 matrix of Timepix edgeless silicon pixelated detectors with tiling based on overlaying rows (i.e. assembled so that no gap is present between individual rows of detectors). We compare the results from both detectors with the scanning electron microscopy on selected slices in transversal plane. It has been shown that the photon counting detector can provide approx. 3× better resolution of the details in low-attenuating materials than the integrating flat panel detectors. We demonstrate that employment of a large area photon counting detector is a good choice for imaging of low attenuating materials with the resolution sufficient for numerical simulations.

Large Scale Laser Two-Photon Polymerization Structuring for Fabrication of Artificial Polymeric Scaffolds for Regenerative Medicine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malinauskas, M.; Purlys, V.; Zukauskas, A.

2010-11-10

We present a femtosecond Laser Two-Photon Polymerization (LTPP) system of large scale three-dimensional structuring for applications in tissue engineering. The direct laser writing system enables fabrication of artificial polymeric scaffolds over a large area (up to cm in lateral size) with sub-micrometer resolution which could find practical applications in biomedicine and surgery. Yb:KGW femtosecond laser oscillator (Pharos, Light Conversion. Co. Ltd.) is used as an irradiation source (75 fs, 515 nm (frequency doubled), 80 MHz). The sample is mounted on wide range linear motor driven stages having 10 nm sample positioning resolution (XY--ALS130-100, Z--ALS130-50, Aerotech, Inc.). These stages guarantee anmore » overall travelling range of 100 mm into X and Y directions and 50 mm in Z direction and support the linear scanning speed up to 300 mm/s. By moving the sample three-dimensionally the position of laser focus in the photopolymer is changed and one is able to write complex 3D (three-dimensional) structures. An illumination system and CMOS camera enables online process monitoring. Control of all equipment is automated via custom made computer software ''3D-Poli'' specially designed for LTPP applications. Structures can be imported from computer aided design STereoLihography (stl) files or programmed directly. It can be used for rapid LTPP structuring in various photopolymers (SZ2080, AKRE19, PEG-DA-258) which are known to be suitable for bio-applications. Microstructured scaffolds can be produced on different substrates like glass, plastic and metal. In this paper, we present microfabricated polymeric scaffolds over a large area and growing of adult rabbit myogenic stem cells on them. Obtained results show the polymeric scaffolds to be applicable for cell growth practice. It exhibit potential to use it for artificial pericardium in the experimental model in the future.« less

Large Scale Laser Two-Photon Polymerization Structuring for Fabrication of Artificial Polymeric Scaffolds for Regenerative Medicine

NASA Astrophysics Data System (ADS)

Malinauskas, M.; Purlys, V.; Žukauskas, A.; Rutkauskas, M.; Danilevičius, P.; Paipulas, D.; Bičkauskaitė, G.; Bukelskis, L.; Baltriukienė, D.; Širmenis, R.; Gaidukevičiutė, A.; Bukelskienė, V.; Gadonas, R.; Sirvydis, V.; Piskarskas, A.

2010-11-01

We present a femtosecond Laser Two-Photon Polymerization (LTPP) system of large scale three-dimensional structuring for applications in tissue engineering. The direct laser writing system enables fabrication of artificial polymeric scaffolds over a large area (up to cm in lateral size) with sub-micrometer resolution which could find practical applications in biomedicine and surgery. Yb:KGW femtosecond laser oscillator (Pharos, Light Conversion. Co. Ltd.) is used as an irradiation source (75 fs, 515 nm (frequency doubled), 80 MHz). The sample is mounted on wide range linear motor driven stages having 10 nm sample positioning resolution (XY—ALS130-100, Z—ALS130-50, Aerotech, Inc.). These stages guarantee an overall travelling range of 100 mm into X and Y directions and 50 mm in Z direction and support the linear scanning speed up to 300 mm/s. By moving the sample three-dimensionally the position of laser focus in the photopolymer is changed and one is able to write complex 3D (three-dimensional) structures. An illumination system and CMOS camera enables online process monitoring. Control of all equipment is automated via custom made computer software "3D-Poli" specially designed for LTPP applications. Structures can be imported from computer aided design STereoLihography (stl) files or programmed directly. It can be used for rapid LTPP structuring in various photopolymers (SZ2080, AKRE19, PEG-DA-258) which are known to be suitable for bio-applications. Microstructured scaffolds can be produced on different substrates like glass, plastic and metal. In this paper, we present microfabricated polymeric scaffolds over a large area and growing of adult rabbit myogenic stem cells on them. Obtained results show the polymeric scaffolds to be applicable for cell growth practice. It exhibit potential to use it for artificial pericardium in the experimental model in the future.

Sensing sheets based on large area electronics for fatigue crack detection

NASA Astrophysics Data System (ADS)

Yao, Yao; Glisic, Branko

2015-03-01

Reliable early-stage damage detection requires continuous structural health monitoring (SHM) over large areas of structure, and with high spatial resolution of sensors. This paper presents the development stage of prototype strain sensing sheets based on Large Area Electronics (LAE), in which thin-film strain gauges and control circuits are integrated on the flexible electronics and deposited on a polyimide sheet that can cover large areas. These sensing sheets were applied for fatigue crack detection on small-scale steel plates. Two types of sensing-sheet interconnects were designed and manufactured, and dense arrays of strain gauge sensors were assembled onto the interconnects. In total, four (two for each design type) strain sensing sheets were created and tested, which were sensitive to strain at virtually every point over the whole sensing sheet area. The sensing sheets were bonded to small-scale steel plates, which had a notch on the boundary so that fatigue cracks could be generated under cyclic loading. The fatigue tests were carried out at the Carleton Laboratory of Columbia University, and the steel plates were attached through a fixture to the loading machine that applied cyclic fatigue load. Fatigue cracks then occurred and propagated across the steel plates, leading to the failure of these test samples. The strain sensor that was close to the notch successfully detected the initialization of fatigue crack and localized the damage on the plate. The strain sensor that was away from the crack successfully detected the propagation of fatigue crack based on the time history of measured strain. Overall, the results of the fatigue tests validated general principles of the strain sensing sheets for crack detection.

TILT ANGLE AND FOOTPOINT SEPARATION OF SMALL AND LARGE BIPOLAR SUNSPOT REGIONS OBSERVED WITH HMI

DOE Office of Scientific and Technical Information (OSTI.GOV)

McClintock, B. H.; Norton, A. A., E-mail: u1049686@umail.usq.edu.au, E-mail: aanorton@stanford.edu

2016-02-10

We investigate bipolar sunspot regions and how tilt angle and footpoint separation vary during emergence and decay. The Helioseismic and Magnetic Imager on board the Solar Dynamic Observatory collects data at a higher cadence than historical records and allows for a detailed analysis of regions over their lifetimes. We sample the umbral tilt angle, footpoint separation, and umbral area of 235 bipolar sunspot regions in Helioseismic and Magnetic Imager—Debrecen Data with an hourly cadence. We use the time when the umbral area peaks as time zero to distinguish between the emergence and decay periods of each region and we limitmore » our analysis of tilt and separation behavior over time to within ±96 hr of time zero. Tilt angle evolution is distinctly different for regions with small (≈30 MSH), midsize (≈50 MSH), and large (≈110 MSH) maximum umbral areas, with 45 and 90 MSH being useful divisions for separating the groups. At the peak umbral area, we determine median tilt angles for small (7.°6), midsize (5.°9), and large (9.°3) regions. Within ±48 hr of the time of peak umbral area, large regions steadily increase in tilt angle, midsize regions are nearly constant, and small regions show evidence of negative tilt during emergence. A period of growth in footpoint separation occurs over a 72-hr period for all of the regions from roughly 40 to 70 Mm. The smallest bipoles (<9 MSH) are outliers in that they do not obey Joy's law and have a much smaller footpoint separation. We confirm the Muñoz-Jaramillo et al. results that the sunspots appear to be two distinct populations.« less

Environment and gut morphology influence microplastic retention in langoustine, Nephrops norvegicus.

PubMed

Welden, Natalie A C; Cowie, Phillip R

2016-07-01

Over the past twenty years microplastic pollution has been recorded in all major marine habitats, and is now considered to be of high environmental concern. Correspondingly, the number of reports of microplastic ingestion by marine species is increasing. Despite this, there are still relatively few studies which address the uptake and retention of microplastic in wild populations. Langoustine, Nephrops norvegicus, sampled from the Clyde Sea Area, have previously been seen to contain large aggregations of microplastic fibres. The large proportion of contaminated individuals and size of the microplastic aggregations observed suggests that Nephrops are at high risk of microplastic ingestion. In this study the levels of ingested microplastic in populations of N. norvegicus from the Clyde Sea Area, North Minch and North Sea are examined. Animals in the near-shore, Clyde Sea population showed both a higher percentage of microplastic containing individuals and much greater weights of microplastic retained in the gut. N. norvegicus revealed that only a small percentage of individuals from the North Sea and Minch contained microplastic, predominantly single strands. An expanded sample from the Clyde Sea Area was examined to identify the factors influencing microplastic retention. This revealed that males, larger individuals, and animals that had recently moulted contained lower levels of microplastic. The presence of identified food items in the gut was not seen to correlate with microplastic loads. Observations of microplastic in the shed stomach lining of recently moulted individuals and the lack of aggregations in wild-caught individuals suggests that ecdysis is the primary route of microplastic loss by N. norvegicus. Therefore the large aggregations observed in wild-caught animals are believed to build up over extended periods as a result of the complex gut structure of N. norvegicus. Copyright © 2016 Elsevier Ltd. All rights reserved.

The benefits of utilising geo-mapping for visualising the vitamin D status of Dublin city and the surrounding urban districts.

PubMed

Laird, E; Shannon, T; Crowley, V E F; Healy, M

2017-11-01

There have been few published reports of visualising vitamin D status at a micro level, i.e., within large individual urban centres of countries. To produce a visual map of the vitamin D status [25-hydroxy vitamin D-25(OH)D] of a large urban centre (n > 350,000) incorporating the regions of Dublin city that constitute the general practitioner catchment area of a large academic teaching adult hospital. An observational investigation of 5287 free living Irish adults (>18 years). Approximately, 15.2 % of those sampled in the winter period (October-February) were vitamin D deficient (<30 nmol/L) compared with 10.8 % of those sampled in the summer period (March-September). Vitamin D tests requested from the most social economically deprived urban locations (Dublin 8 and Lucan postal districts) had the highest rates of deficiency (23.5 and 20.4 %, respectively, both seasons). On average, females had a significantly higher 25(OH)D concentration compared with males (57.9 vs 52.3 nmol/L, respectively), while the younger participants (18-50 years) mean 25(OH)D concentration was 27 % lower in winter and 20.7 % lower in summer in comparison with the older participants (>50 years) (P < 0.0001). For the first time in Ireland, a visual depiction of data can be used to aid in the rapid identification of vitamin D status trends within a major urban area. These findings provide useful data to help inform public health policy regarding endemic vitamin D insufficiency to help target the population groups and resident location areas most at risk.

Reindeer grazing in subarctic boreal forest - influences on the soil carbon dynamics

NASA Astrophysics Data System (ADS)

Koster, Kajar; Berninger, Frank; Köster, Egle; Pumpanen, Jukka

2015-04-01

Reindeer (Rangifer tarandus L.) are the most important large mammalian herbivores in the northern ecosystems , which have many effects on plant diversity, soil nutrient cycling and soil organic matter decomposition. Changes caused by reindeer in vegetation have indirect effects on physical features of the soil e.g. soil microclimate, root biomass and also on soil C dynamics. Earlier, the role of reindeer grazing in ground vegetation dynamics and in soil carbon (C) dynamics has been mostly investigated in open tundra heaths. The objectives of this study were to examine if and how the reindeer grazing (and the possible temperature changes in soil caused by heavy grazing) is affecting the soil C dynamics (CO2 efflux from the soil, C storage in soil, microbial biomass in the soil). In a field experiment in Finnish Lapland, in Värriö Strict Nature Reserve (67° 46' N, 29° 35' E) we have assessed the changes occurring in above- and belowground biomasses, and soil C dynamics (CO2 efflux, soil C content, soil microbial biomass C) among areas grazed and ungrazed by reindeer. Our study areas are located in the northern boreal subarctic coniferous forest at the zone of the last intact forest landscapes in Fennoscandia, where large areas of relatively undisturbed subarctic Scots pine (Pinus sylvestris L.) forests can still be found. The sample plots located in the Värriö Strict Nature Reserve (10 sample plots in total established in year 2013) are situated along the borderline between Finland and Russia, where the ungrazed area was excluded from the reindeer grazing already in 1918, to prevent the Finnish reindeer from going to the Russian side and there are not many reindeer on Russian side of the area. To characterize the stands we have established circular sample plots on areas with a radius of 11.28 m, where different tree characteristics were measured (diameter at 1.3 m, height, height of a tree, crown height, crown diameter, stand age, etc.). On every sample plot, four 0.5 x 0.5 m ground vegetation squares were established for species composition and recovery measurements. The squares were photographed for ground vegetation coverage analyses and definition of species composition. Ground vegetation biomass was determined from 4 sample squares (0.2 x 0.2 m) located systematically inside the circular sample plots (close to the ground vegetation squares). For soil C content measurements 5 soil cores (150 mm in length and 50 mm in diameter) were taken from every sample plot in Värriö and in Sodankylä. The soil cores were divided according to the morphological soil horizons; to litter and organic layer (F-horizon) and humus layer (O-horizon). The layers in mineral soil were divided to eluvial (A-horizon) and illuvial (B-horizon), and sieved. All roots were separated for root biomass calculations. The soil C content was measured with an elemental analyser (varioMAX CN elemental analyser, Elementar Analysensysteme GmbH, Germany). The soil respiration rates were measured only in Värriö study areas. In order to determine the CO2 efflux from soil to atmosphere, manual chamber measurements with a diffusion type CO2 probe (GMP343), were performed on 6 collars at each sample plot from June till September (five times per collar) at measuring intervals of two weeks. Soil microbial biomass was measured from five soil samples (soil from lower humus layer) per sample plot in Värriö. To determine the soil microbial C biomass (Cmic) and soil microbial N biomass (Nmic) chloroform fumigation direct extraction method was used. The average soil temperatures during the growing season (from June till September) were similar in all sample plots in Värriö, ranging from 10.9 to 11.5 ° C. There were also no differences between daily average temperatures or soil moisture between grazed and ungrazed areas. There was no statistically significant effect of reindeer grazing on soil C content, although it was mainly higher in grazed area compared to the ungrazed area. Also there was no significant differences in the soil CO2 efflux between the grazed and ungrazed area. This means that although the soil CO2 efflux was mostly lower in the ungrazed area, reindeer herding had no significant influence on the soil CO2 efflux. The CO2 effluxes were lowest in June. In July and August, the CO2 effluxes were more than two times higher compared to June. The microbial biomass C (Cmic) measured from humus horizon was lower in the grazed areas compared to the ungrazed areas, but the difference was not statistically significant. However, the microbial biomass N (Nmic) was significantly lower (p > 0.05) in the grazed areas compared to the ungrazed areas. We found also that grazing decreased significantly the biomass and cover of lichens in the coniferous forests. In Sodankylä the biomass of lichens was decreased around 74% due to grazing. In Värriö the decrease was even bigger, there the amount of lichen biomass was decreased more than 90% due to reindeer grazing. Ttal above ground biomass was higher in the area where no reindeer grazing had occurred. Moreover, the tree biomass was higher in the area with no grazing and tree regeneration was heavily affected by grazing, as we had much less tree regeneration in the grazed areas compared to the ungrazed areas.

Microbiological sampling of swine carcasses: a comparison of data obtained by swabbing with medical gauze and data collected routinely by excision at Swedish abattoirs.

PubMed

Lindblad, M

2007-09-15

Swab sample data from a 13-month microbiological baseline study of swine carcasses at Swedish abattoirs were combined with excision sample data collected routinely at five abattoirs. The aim was to compare the numbers of total aerobic counts, Enterobacteriaceae, and Escherichia coli, recovered by swabbing four carcass sites with gauze (total area 400 cm2) with those obtained by excision at equivalent sites (total area 20 cm2). The results are considered in relation to the process hygiene criteria that are stated in Commission Regulation (EC) No 2073/2005. These criteria apply only to destructive sampling of total aerobic counts and Enterobacteriaceae, but alternative sampling schemes, as well as alternative indicator organisms such as E. coli, are allowed if equivalent guarantees of food safety can be provided. Swab sampling resulted in higher mean log numbers of total aerobic counts at four of the five abattoirs, compared with excision, and lower or equal standard deviations at all abattoirs. The percentage of swab and excision samples positive for Enterobacteriaceae at the different abattoirs ranged from 68 to 100% and 15 to 24%, respectively. Similarly, the percentages of swab samples that were positive for E. coli were higher than the percentages of positive excision samples (range 52 to 84% and 3 to 14%, respectively). Due to the low percentage of positive excision results, the mean log numbers of Enterobacteriaceae and E. coli were only compared at two and one abattoirs, respectively, using log probability regression to substitute censored observations. Higher mean log numbers of Enterobacteriaceae were recovered by swabbing compared with excision at one abattoir, whereas the numbers of Enterobacteriaceae and E. coli did not differ significantly between sampling methods at one abattoir. This study suggests that the same process hygiene criteria as those stipulated for excision can be used for swabbing with gauze without compromising food safety. For monitoring of low numbers of Enterobacteriaceae and E. coli, like those found on swine carcasses at Swedish abattoirs, the results also show that swabbing of a relatively large area is superior to excision of a smaller area.

Nondestructive Analysis of Astromaterials by Micro-CT and Micro-XRF Analysis for PET Examination

NASA Technical Reports Server (NTRS)

Zeigler, R. A.; Righter, K.; Allen, C. C.

2013-01-01

An integral part of any sample return mission is the initial description and classification of returned samples by the preliminary examination team (PET). The goal of the PET is to characterize and classify returned samples and make this information available to the larger research community who then conduct more in-depth studies on the samples. The PET tries to minimize the impact their work has on the sample suite, which has in the past limited the PET work to largely visual, nonquantitative measurements (e.g., optical microscopy). More modern techniques can also be utilized by a PET to nondestructively characterize astromaterials in much more rigorous way. Here we discuss our recent investigations into the applications of micro-CT and micro-XRF analyses with Apollo samples and ANSMET meteorites and assess the usefulness of these techniques in future PET. Results: The application of micro computerized tomography (micro-CT) to astromaterials is not a new concept. The technique involves scanning samples with high-energy x-rays and constructing 3-dimensional images of the density of materials within the sample. The technique can routinely measure large samples (up to approx. 2700 cu cm) with a small individual voxel size (approx. 30 cu m), and has the sensitivity to distinguish the major rock forming minerals and identify clast populations within brecciated samples. We have recently run a test sample of a terrestrial breccia with a carbonate matrix and multiple igneous clast lithologies. The test results are promising and we will soon analyze a approx. 600 g piece of Apollo sample 14321 to map out the clast population within the sample. Benchtop micro x-ray fluorescence (micro-XRF) instruments can rapidly scan large areas (approx. 100 sq cm) with a small pixel size (approx. 25 microns) and measure the (semi) quantitative composition of largely unprepared surfaces for all elements between Be and U, often with sensitivity on the order of a approx. 100 ppm. Our recent testing of meteorite and Apollo samples on micro-XRF instruments has shown that they can easily detect small zircons and phosphates (approx. 10 m), distinguish different clast lithologies within breccias, and identify different lithologies within small rock fragments (2-4 mm soil Apollo soil fragments).

Integration of NASA/GSFC and USGS Rock Magnetic Databases.

NASA Astrophysics Data System (ADS)

Nazarova, K. A.; Glen, J. M.

2004-05-01

A global Magnetic Petrology Database (MPDB) was developed and continues to be updated at NASA/Goddard Space Flight Center. The purpose of this database is to provide the geomagnetic community with a comprehensive and user-friendly method of accessing magnetic petrology data via the Internet for a more realistic interpretation of satellite (as well as aeromagnetic and ground) lithospheric magnetic anomalies. The MPDB contains data on rocks from localities around the world (about 19,000 samples) including the Ukranian and Baltic Shields, Kamchatka, Iceland, Urals Mountains, etc. The MPDB is designed, managed and presented on the web as a research oriented database. Several database applications have been specifically developed for data manipulation and analysis of the MPDB. The geophysics unit at the USGS in Menlo Park has over 17,000 rock-property data, largely from sites within the western U.S. This database contains rock-density and rock-magnetic parameters collected for use in gravity and magnetic field modeling, and paleomagnetic studies. Most of these data were taken from surface outcrops and together they span a broad range of rock types. Measurements were made either in-situ at the outcrop, or in the laboratory on hand samples and paleomagnetic cores acquired in the field. The USGS and NASA/GSFC data will be integrated as part of an effort to provide public access to a single, uniformly maintained database. Due to the large number of data and the very large area sampled, the database can yield rock-property statistics on a broad range of rock types; it is thus applicable to study areas beyond the geographic scope of the database. The intent of this effort is to provide incentive for others to further contribute to the database, and a tool with which the geophysical community can entertain studies formerly precluded.

Attenuated total reflection-Fourier transform infrared imaging of large areas using inverted prism crystals and combining imaging and mapping.

PubMed

Chan, K L Andrew; Kazarian, Sergei G

2008-10-01

Attenuated total reflection-Fourier transform infrared (ATR-FT-IR) imaging is a very useful tool for capturing chemical images of various materials due to the simple sample preparation and the ability to measure wet samples or samples in an aqueous environment. However, the size of the array detector used for image acquisition is often limited and there is usually a trade off between spatial resolution and the field of view (FOV). The combination of mapping and imaging can be used to acquire images with a larger FOV without sacrificing spatial resolution. Previous attempts have demonstrated this using an infrared microscope and a Germanium hemispherical ATR crystal to achieve images of up to 2.5 mm x 2.5 mm but with varying spatial resolution and depth of penetration across the imaged area. In this paper, we demonstrate a combination of mapping and imaging with a different approach using an external optics housing for large ATR accessories and inverted ATR prisms to achieve ATR-FT-IR images with a large FOV and reasonable spatial resolution. The results have shown that a FOV of 10 mm x 14 mm can be obtained with a spatial resolution of approximately 40-60 microm when using an accessory that gives no magnification. A FOV of 1.3 mm x 1.3 mm can be obtained with spatial resolution of approximately 15-20 microm when using a diamond ATR imaging accessory with 4x magnification. No significant change in image quality such as spatial resolution or depth of penetration has been observed across the whole FOV with this method and the measurement time was approximately 15 minutes for an image consisting of 16 image tiles.

Assessing Resiliency in a Large Lake Receiving Mine Tailings Waste: Impacts of Major Environmental Disturbance.

NASA Astrophysics Data System (ADS)

Petticrew, Ellen; Owens, Philip; Albers, Sam

2016-04-01

On 4th August 2014, the tailings impoundment of the Mount Polley copper and gold mine in British Columbia failed. Material from the impoundment (surface area = 2.7 km2) flowed into nearby Polley Lake and Hazeltine Creek, before discharging into Quesnel Lake, a large (ca. 100 km long, >500 m deep), relatively pristine lake. Initial estimates suggest that approximately 25 Mm3 of tailings (water and solids) and eroded soils and surficial materials from Hazeltine Creek were delivered to Quesnel Lake, raising the lake by 7.7 cm. Much of this material was deposited at the bottom of Quesnel Lake but a plume of fine-grained sediment (D50 of ca. 1 μm) remained suspended in the water column. The impact of the distribution of this sediment was monitored over the next 15 months using water column profiling for temperature, conductivity, fluorescence and turbidity with depth. The plume movement was regulated by natural processes associated with the physical limnology of this large fjord lake, specifically, seiche events which transferred suspended particles both up-lake, against the flow regime, and down-lake into the Quesnel River. Samples of lake water and bottom sediment taken from the impacted area show elevated levels of total metals and other elements, which may have important ecosystem implications in this watershed. Indeed, the breach occurred at a time when a peak run of sockeye salmon were returning to their natal streams in the Quesnel basin. Zooplankton sampling for metals was initiated in fall 2014 to determine up take of metals into the food web. This poster describes the failure of the impoundment dam and presents results of sampling the aquatic environment over the first fifteen months of impact.

Heavy metal pollution in soil associated with a large-scale cyanidation gold mining region in southeast of Jilin, China.

PubMed

Chen, Mo; Lu, Wenxi; Hou, Zeyu; Zhang, Yu; Jiang, Xue; Wu, Jichun

2017-01-01

Different gold mining and smelting processes can lead to distinctive heavy metal contamination patterns and results. This work examined heavy metal pollution from a large-scale cyanidation gold mining operation, which is distinguished from artisanal and small-scale amalgamation gold mining, in Jilin Province, China. A total of 20 samples including one background sample were collected from the surface of the mining area and the tailings pond in June 2013. These samples were analyzed for heavy metal concentrations and degree of pollution as well as sources of Cr, Cu, Zn, Pb, Ni, Cd, As, and Hg. The mean concentrations of Pb, Hg, and Cu (819.67, 0.12, and 46.92 mg kg -1 , respectively) in soil samples from the gold mine area exceeded local background values. The mean Hg content was less than the first-class standard of the Environmental Quality for Soils, which suggested that the cyanidation method is helpful for reducing Hg pollution. The geochemical accumulation index and enrichment factor results indicated clear signs that enrichment was present for Pb, Cu, and Hg, with the presence of serious Pb pollution and moderate presence to none of Hg and Cu pollution. Multivariate statistical analysis showed that there were three metal sources: (1) Pb, Cd, Cu, and As came from anthropogenic sources; (2) Cr and Zn were naturally occurring; whereas (3) Hg and Ni had a mix of anthropogenic and natural sources. Moreover, the tailings dam plays an important role in intercepting the tailings. Furthermore, the potential ecological risk assessment results showed that the study area poses a potentially strong risk to the ecological health. Furthermore, Pb and Hg (due to high concentration and high toxicity, respectively) are major pollutants on the risk index, and both Pb and Hg pollution should be of great concern at the Haigou gold mines in Jilin, China.

[Evaluation and source analysis of the mercury pollution in soils and vegetables around a large-scale zinc smelting plant].

PubMed

Liu, Fang; Wang, Shu-Xiao; Wu, Qing-Ru; Lin, Hai

2013-02-01

The farming soil and vegetable samples around a large-scale zinc smelter were collected for mercury content analyses, and the single pollution index method with relevant regulations was used to evaluate the pollution status of sampled soils and vegetables. The results indicated that the surface soil and vegetables were polluted with mercury to different extent. Of the soil samples, 78% exceeded the national standard. The mercury concentration in the most severely contaminated area was 29 times higher than the background concentration, reaching the severe pollution degree. The mercury concentration in all vegetable samples exceeded the standard of non-pollution vegetables. Mercury concentration, in the most severely polluted vegetables were 64.5 times of the standard, and averagely the mercury concentration in the vegetable samples was 25.4 times of the standard. For 85% of the vegetable samples, the mercury concentration, of leaves were significantly higher than that of roots, which implies that the mercury in leaves mainly came from the atmosphere. The mercury concentrations in vegetable roots were significantly correlated with that in soils, indicating the mercury in roots was mainly from soil. The mercury emissions from the zinc smelter have obvious impacts on the surrounding soils and vegetables. Key words:zinc smelting; mercury pollution; soil; vegetable; mercury content

Temperature data from Norwegian and Russian waters of the northern Barents Sea collected by free-living ringed seals

NASA Astrophysics Data System (ADS)

Lydersen, Christian; Anders Nøst, Ole; Kovacs, Kit M.; Fedak, Mike A.

2004-05-01

Free-living ringed seals ( N=11) equipped with satellite-relayed data loggers (SRDLs) with incorporated oceanographic-quality temperature sensors were used to collect data from a large sector of the northern Barents Sea during the autumn and early winter. A total of 2346 temperature profiles were collected over a 4-month period from Norwegian and Russian arctic waters in areas that were at times 90-100% ice-covered. Temperature distributions at different depths from northeastern parts of Svalbard, Norway show warm North Atlantic water (NAW) flowing along the continental slope and gradually cooling at all depths as it flows eastwards. The data suggest that most of the cooling takes place west of 30°E. Vertical temperature profiles from the area between Svalbard and Franz Josef Land, Russia show how the surface water cools during freeze-up and demonstrate a warm water flow, which is probably NAW, coming in from the north through a deep trench west of Franz Josef Land. Global oceanographic and climate models require improved oceanographic databases from crucial areas where important hydrological phenomena occur. Such areas in arctic waters are often inaccessible during winter and logistically difficult to reach even in summer. The present study demonstrates how large amounts of oceanographic information can be collected and retrieved in a cost-efficient manner using ice-associated marine mammals as carrier of oceanographic sampling equipment. In addition to the oceanographic value of the data collected by marine mammals in this manner, a vast amount of information regarding the habitat of these animals is concomitantly sampled.

29 CFR Appendix E to Subpart M of... - Sample Fall Protection Plan

Code of Federal Regulations, 2012 CFR

2012-07-01

... system shall not be used when the wind is strong enough to cause loads with large surface areas to swing out of radius, or result in loss of control of the load, or when weather conditions cause the walking... column is through the slab opening, there will no longer exist a fall hazard at this location. III...

29 CFR Appendix E to Subpart M of... - Sample Fall Protection Plan

Code of Federal Regulations, 2013 CFR

2013-07-01

... system shall not be used when the wind is strong enough to cause loads with large surface areas to swing out of radius, or result in loss of control of the load, or when weather conditions cause the walking... column is through the slab opening, there will no longer exist a fall hazard at this location. III...

29 CFR Appendix E to Subpart M of... - Sample Fall Protection Plan

Code of Federal Regulations, 2011 CFR

2011-07-01

... system shall not be used when the wind is strong enough to cause loads with large surface areas to swing out of radius, or result in loss of control of the load, or when weather conditions cause the walking... column is through the slab opening, there will no longer exist a fall hazard at this location. III...

Wildlife scientists and wilderness managers finding common ground with noninvasive and nonintrusive sampling of wildlife

Treesearch

Michael K. Schwartz; Peter B. Landres; David J. Parsons

2011-01-01

Iconic wildlife species such as grizzly bears, wolves, lynx, and wolverines are often associated with wilderness. Wilderness may provide some of the last, and best, remaining places for such species because wilderness can offer long-term legislated protection, relatively large areas, and remoteness (Mattson 1997). Indeed, the word wilderness in its original form...

Is Some Data Better than No Data at All? Evaluating the Utility of Secondary Needs Assessment Data

ERIC Educational Resources Information Center

Shamblen, Stephen R.; Dwivedi, Pramod

2010-01-01

Needs assessments in substance abuse prevention often rely on secondary data measures of consumption and consequences to determine what population subgroup and geographic areas should receive a portion of limited resources. Although these secondary data measures have some benefits (e.g. large sample sizes, lack of survey response biases and cost),…

Head Start and Urban Children's School Readiness: A Birth Cohort Study in 18 Cities

ERIC Educational Resources Information Center

Zhai, Fuhua; Brooks-Gunn, Jeanne; Waldfogel, Jane

2010-01-01

In this study, the authors used data from a large longitudinal birth cohort study of primarily low-income children in urban areas, the Fragile Families and Child Wellbeing Study (FFCWS), to investigate the effects of Head Start participation on children's school readiness. The fact that their sample was mainly made up of disadvantaged families…

Community Support for the Public Schools in a Large Metropolitan Area. Final Report.

ERIC Educational Resources Information Center

Smith, Ralph V.; And Others

An extensive survey was conducted in 1965 by a team of white and Negro interviewers in an application of ecological theory to a study of the support relationship between the community and its school system. Findings are based upon interview data from a probability sample of 931 respondents selected from the population of persons 21 years of age…

The power of FIA Phase 3 Crown-Indicator variables to detect change

Treesearch

William Bechtold; KaDonna Randolph; Stanley Zarnoch

2009-01-01

The goal of Phase 3 Detection Monitoring as implemented by the Forest Inventory and Analysis Program is to identify forest ecosystems where conditions might be deteriorating in subtle ways over large areas. At the relatively sparse sampling intensity of the Phase 3 plot network, a rough measure of success for the forest health indicators developed for this purpose is...

Postfire seed rain of black spruce, a semiserotinous conifer, in forests of interior Alaska

Treesearch

Jill Johnstone; Leslie Boby; Emily Tissier; Michelle Mack; Dave Verbyla; Xanthe. Walker

2009-01-01

The availability of viable seed can act as an important constraint on plant regeneration following disturbance. This study presents data on seed quantity and quality for black spruce (Picea mariana (Mill.) B.S.P.), a semiserotinous conifer that dominates large areas of North American boreal forest. We sampled seed rain and viability for 2 years...

Deep-sea benthic megafaunal habitat suitability modelling: A global-scale maximum entropy model for xenophyophores

NASA Astrophysics Data System (ADS)

Ashford, Oliver S.; Davies, Andrew J.; Jones, Daniel O. B.

2014-12-01

Xenophyophores are a group of exclusively deep-sea agglutinating rhizarian protozoans, at least some of which are foraminifera. They are an important constituent of the deep-sea megafauna that are sometimes found in sufficient abundance to act as a significant source of habitat structure for meiofaunal and macrofaunal organisms. This study utilised maximum entropy modelling (Maxent) and a high-resolution environmental database to explore the environmental factors controlling the presence of Xenophyophorea and two frequently sampled xenophyophore species that are taxonomically stable: Syringammina fragilissima and Stannophyllum zonarium. These factors were also used to predict the global distribution of each taxon. Areas of high habitat suitability for xenophyophores were highlighted throughout the world's oceans, including in a large number of areas yet to be suitably sampled, but the Northeast and Southeast Atlantic Ocean, Gulf of Mexico and Caribbean Sea, the Red Sea and deep-water regions of the Malay Archipelago represented particular hotspots. The two species investigated showed more specific habitat requirements when compared to the model encompassing all xenophyophore records, perhaps in part due to the smaller number and relatively more clustered nature of the presence records available for modelling at present. The environmental variables depth, oxygen parameters, nitrate concentration, carbon-chemistry parameters and temperature were of greatest importance in determining xenophyophore distributions, but, somewhat surprisingly, hydrodynamic parameters were consistently shown to have low importance, possibly due to the paucity of well-resolved global hydrodynamic datasets. The results of this study (and others of a similar type) have the potential to guide further sample collection, environmental policy, and spatial planning of marine protected areas and industrial activities that impact the seafloor, particularly those that overlap with aggregations of these conspicuously large single-celled eukaryotes.

Methane related authigenic carbonates, chimneys and crusts from the Gulf of Cadiz

NASA Astrophysics Data System (ADS)

Magalhães, V.; Vasconcelos, C.; Gaspar, L.; Monteiro, H.; Pinheiro, L.; Ivanov, M.; Díaz-del-Río, V.; Somoza, L.

2003-04-01

During the TTR 11 and TTR 12 cruises (2001 and 2002), the area south and southwest of the Guadalquivir Diapiric Ridge was intensely surveyed with seismics, side scan sonar (MAK), underwater TV and sampling. This area is characterized by a very strong backscatter on the available side scan sonar images and a very irregular seafloor, with morphological and sedimentological features evidencing fluid escape structures (mud diapirs and mud volcanoes); and sedimentary structures associated with the outflow of the Mediterranean water (MOW). Based on the data and samples collected during the TTR11 and TTR12 cruises, complemented with data from the ANASTYA 2000 and 2001 cruises, it seems that this area corresponds to a large field of carbonate chimneys and crusts. Dredge profiles on the Iberico dome and west of this structure, on the main channel of the MOW, yielded a large amount of carbonate slabs and chimneys. These consist essentially of intrapelbiomicrite. Petrographic and XRD shows that their mineralogical composition consists mainly of dolomite, high magnesium calcite, quartz, feldspar and clays. Bioclasts of plantonic foraminifera (globigerinoids), ostracods and peletts are observed. Iron and manganese oxides are present and the cement is essentially biomicrite. In different samples from the same chimney a variation on the dolomite/calcite ratio is observed from the interior to the external part of the chimney. Values of dolomite show a variation from 47% in the interior to 17 % in the exterior. As regards Si02 (19-16%), Al2O3 (4-3%) and Fe2O3 (5-7%), the variations observed are not significant. Stable isotopic analysis of Carbon shown low d13C values (down to -46.88 per mil vs. PDB) and d18O up to + 4.90 per mil vs.

ANSMET 2013

NASA Technical Reports Server (NTRS)

Adams, Mitzi L.

2014-01-01

From December 2013 to January 2014, MSFC Planetary Scientist Dr. Barbara Cohen participated in the Antarctic Search for Meteorites (ANSMET) 2013-2014 season. With a team of eight, a systematic search of the Antarctic ice in the South Miller Range turned up 333 samples; one of the largest is seen here with Dr. Cohen for scale. Since 1976, ANSMET has recovered more than 25,000 specimens from the ice along the Transantarctic Mountains. The icy surfaces of this area are particularly well suited for meteorite searches because of surface stranding: the surfaces must have bare ice, must be composed of large volumes, and the ice must flow out of the area more slowly than new ice arrives. The ANSMET specimens are currently the only reliable, continuous source of new, nonmicroscopic extraterrestrial material, and will continue to be until planetary sample-return missions are successful. The ANSMET program is supported by grants from the Solar System Exploration Division of NASA. Polar logistics are provided by the Office of Polar Programs of the U.S. National Science Foundation. The Principal Investigator of the current grant is Dr. Ralph P. Harvey at Case Western Reserve University. Dr. Barbara Cohen is seen with a large meteorite from the Antarctic's Miller Range

[Genotypes distribution of hepatitis C virus through multi-center, large sample studies among chronic hepatitis C patients in Chinese Han population].

PubMed

Nie, Hong-ming; Chen, Jian-jie; Wang, Rong; Wang, Cheng-bao; Dong, Hui-lin; Chen, Yi-yun

2012-05-01

To understand the distribution of hepatitis C virus (HCV) genotypes in China. A national multi-center, large sample epidemiological survey was carried out and certified by an international third-party testing organization. Internationally accepted method for sequencing analysis of viral genotype was used. Patients were those suffered from the 4 major genotypes of chronic hepatitis C, including nine subtypes, which were dominated by genotype 1 (69.6%), with type 1b in particular (accounting for 68.38%). Among the rare gene-6, we saw more subtypes of 6a. In the south, central, and north areas, there was no significant difference seen between the south and the north areas in the distribution of the genotype 1. However, the rate of gene type 2a increased gradually from south to north. In terms of less common type of gene 3b and gene-6, they were seen mainly in the southern provinces. In China, Patients with chronic hepatitis C had 4 HCV genotypes, with 9 subtypes. The rarely seen genotypes 3b and 6 were mainly distributed in the southern provinces.