Development and experimental study of large size composite plasma immersion ion implantation device

NASA Astrophysics Data System (ADS)

Falun, SONG; Fei, LI; Mingdong, ZHU; Langping, WANG; Beizhen, ZHANG; Haitao, GONG; Yanqing, GAN; Xiao, JIN

2018-01-01

Plasma immersion ion implantation (PIII) overcomes the direct exposure limit of traditional beam-line ion implantation, and is suitable for the treatment of complex work-piece with large size. PIII technology is often used for surface modification of metal, plastics and ceramics. Based on the requirement of surface modification of large size insulating material, a composite full-directional PIII device based on RF plasma source and metal plasma source is developed in this paper. This device can not only realize gas ion implantation, but also can realize metal ion implantation, and can also realize gas ion mixing with metal ions injection. This device has two metal plasma sources and each metal source contains three cathodes. Under the condition of keeping the vacuum unchanged, the cathode can be switched freely. The volume of the vacuum chamber is about 0.94 m3, and maximum vacuum degree is about 5 × 10-4 Pa. The density of RF plasma in homogeneous region is about 109 cm-3, and plasma density in the ion implantation region is about 1010 cm-3. This device can be used for large-size sample material PIII treatment, the maximum size of the sample diameter up to 400 mm. The experimental results show that the plasma discharge in the device is stable and can run for a long time. It is suitable for surface treatment of insulating materials.

Observations of Precipitation Size and Fall Speed Characteristics within Coexisting Rain and Wet Snow

NASA Technical Reports Server (NTRS)

Yuter, Sandra E.; Kingsmill, David E.; Nance, Louisa B.; Loeffler-Mang, Martin

2006-01-01

Ground-based measurements of particle size and fall speed distributions using a Particle Size and Velocity (PARSIVEL) disdrometer are compa red among samples obtained in mixed precipitation (rain and wet snow) and rain in the Oregon Cascade Mountains and in dry snow in the Rock y Mountains of Colorado. Coexisting rain and snow particles are distinguished using a classification method based on their size and fall sp eed properties. The bimodal distribution of the particles' joint fall speed-size characteristics at air temperatures from 0.5 to 0 C suggests that wet-snow particles quickly make a transition to rain once mel ting has progressed sufficiently. As air temperatures increase to 1.5 C, the reduction in the number of very large aggregates with a diame ter > 10 mm coincides with the appearance of rain particles larger than 6 mm. In this setting. very large raindrops appear to be the result of aggregates melting with minimal breakup rather than formation by c oalescence. In contrast to dry snow and rain, the fall speed for wet snow has a much weaker correlation between increasing size and increasing fall speed. Wet snow has a larger standard deviation of fall spee d (120%-230% relative to dry snow) for a given particle size. The ave rage fall speed for observed wet-snow particles with a diameter great er than or equal to 2.4 mm is 2 m/s with a standard deviation of 0.8 m/s. The large standard deviation is likely related to the coexistence of particles of similar physical size with different percentages of melting. These results suggest that different particle sizes are not required for aggregation since wet-snow particles of the same size can have different fall speeds. Given the large standard deviation of fa ll speeds in wet snow, the collision efficiency for wet snow is likely larger than that of dry snow. For particle sizes between 1 and 10 mm in diameter within mixed precipitation, rain constituted I % of the particles by volume within the isothermal layer at 0 C and 4% of the particles by volume for the region just below the isothermal layer where air temperatures rise from 0" to 0.5"C. As air temperatures increa sed above 0.5 C, the relative proportions of rain versus snow particl es shift dramatically and raindrops become dominant. The value of 0.5 C for the sharp transition in volume fraction from snow to rain is sl ightly lower than the range from 1 .l to 1.7 C often used in hydrolog ical models.

Nearly ideal binary communication in squeezed channels

NASA Astrophysics Data System (ADS)

Paris, Matteo G.

2001-07-01

We analyze the effect of squeezing the channel in binary communication based on Gaussian states. We show that for coding on pure states, squeezing increases the detection probability at fixed size of the strategy, actually saturating the optimal bound already for moderate signal energy. Using Neyman-Pearson lemma for fuzzy hypothesis testing we are able to analyze also the case of mixed states, and to find the optimal amount of squeezing that can be effectively employed. It results that optimally squeezed channels are robust against signal mixing, and largely improve the strategy power by comparison with coherent ones.

Rack 'em, pack 'em and stack 'em: challenges and opportunities in teaching large classes in higher education.

PubMed

Kumar, Saravana

2013-01-01

The higher education sector is undergoing tremendous change, driven by complex driving forces including financial, administrative, and organisational and stakeholder expectations. It is in this challenging environment, educators are required to maintain and improve the quality of teaching and learning outcomes while contending with increasing class sizes. Despite mixed evidence on the effectiveness of large classes on student outcomes, large classes continue to play an important part in higher education. While large classes pose numerous challenges, they also provide opportunities for innovative solutions. This paper provides an overview of these challenges and highlights opportunities for innovative solutions.

How to test validity in orthodontic research: a mixed dentition analysis example.

PubMed

Donatelli, Richard E; Lee, Shin-Jae

2015-02-01

The data used to test the validity of a prediction method should be different from the data used to generate the prediction model. In this study, we explored whether an independent data set is mandatory for testing the validity of a new prediction method and how validity can be tested without independent new data. Several validation methods were compared in an example using the data from a mixed dentition analysis with a regression model. The validation errors of real mixed dentition analysis data and simulation data were analyzed for increasingly large data sets. The validation results of both the real and the simulation studies demonstrated that the leave-1-out cross-validation method had the smallest errors. The largest errors occurred in the traditional simple validation method. The differences between the validation methods diminished as the sample size increased. The leave-1-out cross-validation method seems to be an optimal validation method for improving the prediction accuracy in a data set with limited sample sizes. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Transformation of Escherichia coli with large DNA molecules by electroporation.

PubMed Central

Sheng, Y; Mancino, V; Birren, B

1995-01-01

We have examined bacterial electroporation with a specific interest in the transformation of large DNA, i.e. molecules > 100 kb. We have used DNA from bacterial artificial chromosomes (BACs) ranging from 7 to 240 kb, as well as BAC ligation mixes containing a range o different sized molecules. The efficiency of electroporation with large DNA is strongly dependent on the strain of Escherichia coli used; strains which offer comparable efficiencies for 7 kb molecules differ in their uptake of 240 kb DNA by as much as 30-fold. Even with a host strain that transforms relatively well with large DNA, transformation efficiency drops dramatically with increasing size of the DNA. Molecules of 240 kb transform approximately 30-fold less well, on a molar basis, than molecules of 80 kb. Maximum transformation of large DNA occurs with different voltage gradients and with different time constants than are optimal for smaller DNA. This provides the opportunity to increase the yield of transformants which have taken up large DNA relative to the number incorporating smaller molecules. We have demonstrated that conditions may be selected which increase the average size of BAC clones generated by electroporation and compare the overall efficiency of each of the conditions tested. Images PMID:7596828

Early competition shapes maize whole-plant development in mixed stands

PubMed Central

Evers, Jochem B.

2014-01-01

Mixed cropping is practised widely in developing countries and is gaining increasing interest for sustainable agriculture in developed countries. Plants in intercrops grow differently from plants in single crops, due to interspecific plant interactions, but adaptive plant morphological responses to competition in mixed stands have not been studied in detail. Here the maize (Zea mays) response to mixed cultivation with wheat (Triticum aestivum) is described. Evidence is provided that early responses of maize to the modified light environment in mixed stands propagate throughout maize development, resulting in different phenotypes compared with pure stands. Photosynthetically active radiation (PAR), red:far-red ratio (R:FR), leaf development, and final organ sizes of maize grown in three cultivation systems were compared: pure maize, an intercrop with a small distance (25cm) between maize and wheat plants, and an intercop with a large distance (44cm) between the maize and the wheat. Compared with maize in pure stands, maize in the mixed stands had lower leaf and collar appearance rates, increased blade and sheath lengths at low ranks and smaller sizes at high ranks, increased blade elongation duration, and decreased R:FR and PAR at the plant base during early development. Effects were strongest in the treatment with a short distance between wheat and maize strips. The data suggest a feedback between leaf initiation and leaf emergence at the plant level and coordination between blade and sheath growth at the phytomer level. A conceptual model, based on coordination rules, is proposed to explain the development of the maize plant in pure and mixed stands. PMID:24307719

Study of the effect of mixing approach on cross-linking efficiency of hyaluronic acid-based hydrogel cross-linked with 1,4-butanediol diglycidyl ether.

PubMed

Al-Sibani, Mohammed; Al-Harrasi, Ahmed; Neubert, Reinhard H H

2016-08-25

Regardless of various strategies reported for cross-linking hyaluronic acid (HA) with 1,4-butanediol diglycidyl ether (BDDE), seeking new strategies that enhance cross-linking efficiency with a low level of cross-linker is essential. In this work, we studied the influence of mixing approach on two cross-linked BDDE-HA hydrogels prepared by two different mixing approaches; the large-batch mixing approach in which the hydrogel quantities were all mixed as a single lump in one container (hydrogel 1), and the small-batches mixing approach in which the hydrogel quantities were divided into smaller batches, mixed separately at various HA/BDDE ratios then combined in one reaction mixture (hydrogel 2). The result showed that the cross-linking reaction was mixing process-dependent. Degradation tests proved that, in relation to hydrogel 1, hydrogel 2 was more stable, and exhibited a higher resistance towards hyaluronidase activity. The swelling ratio of hydrogel 1 was significantly higher than that of hydrogel 2 in distilled water; however, in phosphate buffer saline, both hydrogels showed no significant difference. SEM images demonstrated that hydrogel 2 composite showed a denser network structure and smaller pore-size than hydrogel 1. In comparison to native HA, the occurrence of chemical modification in the cross-linked hydrogels was confirmed by FTIR and NMR distinctive peaks. These peaks also provided evidence that hydrogel 2 exhibited a higher degree of modification than hydrogel 1. In conclusion, the small-batches mixing approach proved to be more effective than large-batch mixing in promoting HA-HA entanglement and increasing the probability of BDDE molecules for binding with HA chains. Copyright © 2016 Elsevier B.V. All rights reserved.

Effects of intake level of a mixed diet on chewing activity and on particle size of ruminated boli, ruminal digesta fractions and faeces of steers.

PubMed

Kovács, P L; Südekum, K H; Stangassinger, M

1997-01-01

This study evaluated the effects of intake of a mixed diet on chewing activity during eating and rumination and the relationship between the chewing activity and the particle size of the ruminated boli, ruminal digesta fractions and faeces in steers. Six ruminally cannulated steers received a mixed forage/concentrate diet (68:32, dry matter basis). The diet was offered twice daily at approximately 1, 1.5 and 2 times the estimated maintenance energy requirements (low, medium and high intake, respectively) in a repeated 3 x 3 Latin square design. The rumens were emptied manually and samples of the ruminated boli and of the ruminal upper strata were collected at four different times throughout the day. The dry matter weight distribution of the total amount of recovered particles was determined by a wet-sieving procedure. Numerically, the effect of intake on the mean particle sizes of the different materials was small. However, the mean particle size was reduced by almost nine tenths from their size at intake of the mixed diet (4.78 mm) to defecation (0.51 mm). The total number of minutes chewing and eating and ruminating increased as the intake level increased. When related to 1 kg of dry matter intake, only the eating and chewing times were significantly longer for the high as compared to the medium intake. Rumination patterns were examined using a cosinor model. Data indicated that the average amount of time spent ruminating also increased as the intake level increased. The overall pattern of rumination was not impaired by higher intake levels. The amount of large (> or = 4 mm) particles that escaped per minute of rumination time between 3 and 7.5 h postfeeding was similar for all the intake levels. It was concluded that an active breakdown process occurred in the rumen which could cope with the higher intake levels of the mixed diet over the range of 1 to 2 times the maintenance energy requirement level.

Relationships between oral morphology and feeding style in the Ungulata: a phylogenetically controlled evaluation.

PubMed

Pérez-Barbería, F J; Gordon, I J

2001-05-22

In ungulates it is argued that specialization in the consumption of a particular type of food (feeding style) is reflected in morphological adaptations of the organs involved in the selection, processing and digestion of food. We analysed the differences in size and morphology of some oral traits that have been functionally related to food-selection ability (muzzle width, incisor-arcade shape, incisor shape), prehension of food (incisor protrusion), food comminution (molar occlusal surface area, hypsodonty (high-crowned molars)) and intake rate (incisor breadth) between ungulate species with different feeding styles (browser, mixed feeder, grazer). Grazers were characterized by large-body-size species. After controlling only for body mass, we found that grazers had wider muzzles and incisors, more-protruding incisors and more-bulky and higher-crowned molars than did mixed feeders and browsers. When the analyses took into account both body mass and phylogeny, only body mass and two out of the three hypsodonty indexes used remained significantly different between feeding styles. Browsers were smaller, on average, than mixed feeders and grazers, whilst grazers and mixed feeders did not differ in size. Also, browsers had shorter and less-bulky molars than did mixed feeders and grazers; the latter two feeding styles did not differ from each other in any of the hypsodonty indexes. We conclude that the adaptation to different dietary types in most of the oral traits studied is subsumed by the effects of body mass and the sharing of common ancestors. We hypothesize that differences in the ability to exploit different food resources primarily result from differences in body mass between species, and also discuss why hypsodonty characterizes feeding styles.

Relationships between oral morphology and feeding style in the Ungulata: a phylogenetically controlled evaluation.

PubMed Central

Pérez-Barbería, F. J.; Gordon, I. J.

2001-01-01

In ungulates it is argued that specialization in the consumption of a particular type of food (feeding style) is reflected in morphological adaptations of the organs involved in the selection, processing and digestion of food. We analysed the differences in size and morphology of some oral traits that have been functionally related to food-selection ability (muzzle width, incisor-arcade shape, incisor shape), prehension of food (incisor protrusion), food comminution (molar occlusal surface area, hypsodonty (high-crowned molars)) and intake rate (incisor breadth) between ungulate species with different feeding styles (browser, mixed feeder, grazer). Grazers were characterized by large-body-size species. After controlling only for body mass, we found that grazers had wider muzzles and incisors, more-protruding incisors and more-bulky and higher-crowned molars than did mixed feeders and browsers. When the analyses took into account both body mass and phylogeny, only body mass and two out of the three hypsodonty indexes used remained significantly different between feeding styles. Browsers were smaller, on average, than mixed feeders and grazers, whilst grazers and mixed feeders did not differ in size. Also, browsers had shorter and less-bulky molars than did mixed feeders and grazers; the latter two feeding styles did not differ from each other in any of the hypsodonty indexes. We conclude that the adaptation to different dietary types in most of the oral traits studied is subsumed by the effects of body mass and the sharing of common ancestors. We hypothesize that differences in the ability to exploit different food resources primarily result from differences in body mass between species, and also discuss why hypsodonty characterizes feeding styles. PMID:11375086

Modeling the Effect of Grain Size Mixing on Thermal Inertia Values Derived from Diurnal and Seasonal THEMIS Measurements

NASA Astrophysics Data System (ADS)

McCarty, C.; Moersch, J.

2017-12-01

Sedimentary processes have slowed over Mars' geologic history. Analysis of the surface today can provide insight into the processes that may have affected it over its history. Sub-resolved checkerboard mixtures of materials with different thermal inertias (and therefore different grain sizes) can lead to differences in thermal inertia values inferred from night and day radiance observations. Information about the grain size distribution of a surface can help determine the degree of sorting it has experienced or it's geologic maturity. Standard methods for deriving thermal inertia from measurements made with THEMIS can give values for the same location that vary by as much as 20% between scenes. Such methods make the assumption that each THEMIS pixel contains material that has uniform thermophysical properties. Here we propose that if a mixture of small and large particles is present within a pixel, the inferred thermal inertia will be strongly dominated by whichever particle is warmer at the time of the measurement because the power radiated by a surface is proportional (by the Stefan-Boltzmann law) to the fourth power of its temperature. This effect will result in a change in thermal inertia values inferred from measurements taken at different times of day and night. Therefore, we expect to see correlation between the magnitude of diurnal variations in inferred thermal inertia values and the degree of grain size mixing for a given pixel location. Preliminary work has shown that the magnitude of such diurnal variation in inferred thermal inertias is sufficient to detect geologically useful differences in grain size distributions. We hypothesize that at least some of the 20% variability in thermal inertias inferred from multiple scenes for a given location could be attributed to sub-pixel grain size mixing rather than uncertainty inherent to the experiment, as previously thought. Mapping the difference in inferred thermal inertias from day and night THEMIS observations may prove to be a new way of distinguishing surfaces that have relatively uniform grain sizes from those that have mixed grain sizes. Assessing the effects of different geologic processes can be aided by noting variations in grain size distributions, so this method may be useful as a new way to extract geologic interpretations from the THEMIS thermal data set.

Litho-kinematic facies model for large landslide deposits in arid settings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yarnold, J.C.; Lombard, J.P.

1989-04-01

Reconnaissance field studies of six large landslide deposits in the S. Basin and Range suggest that a set of characteristic features is common to the deposits of large landslides in an arid setting. These include a coarse boulder cap, an upper massive zone, a lower disrupted zone, and a mixed zone overlying disturbed substrate. The upper massive zone is dominated by crackel breccia. This grades downward into a lower disrupted zone composed of a more matrix-rich breccia that is internally sheared, intruded by clastic dikes, and often contains a cataclasite layer at its base. An underlying discontinuous mixed zone ismore » composed of material from the overlying breccia mixed with material entrained from the underlying substrate. Bedding in the substrate sometimes displays folding and contortion that die out downward. The authors work suggests a spatial zonation of these characteristic features within many landslide deposits. In general, clastic dikes, the basal cataclasite, and folding in the substrate are observed mainly in distal parts of landslides. In most cases, total thickness, thickness of the basal disturbed and mixed zones, and the degree of internal shearing increase distally, whereas maximum clast size commonly decreases distally. Zonation of these features is interpreted to result from kinematics of emplacement that cause generally increased deformation in the distal regions of the landslide.« less

Size-resolved chemical composition, effective density, and optical properties of biomass burning particles

NASA Astrophysics Data System (ADS)

Zhai, Jinghao; Lu, Xiaohui; Li, Ling; Zhang, Qi; Zhang, Ci; Chen, Hong; Yang, Xin; Chen, Jianmin

2017-06-01

Biomass burning aerosol has an important impact on the global radiative budget. A better understanding of the correlations between the mixing states of biomass burning particles and their optical properties is the goal of a number of current studies. In this work, the effective density, chemical composition, and optical properties of rice straw burning particles in the size range of 50-400 nm were measured using a suite of online methods. We found that the major components of particles produced by burning rice straw included black carbon (BC), organic carbon (OC), and potassium salts, but the mixing states of particles were strongly size dependent. Particles of 50 nm had the smallest effective density (1.16 g cm-3) due to a relatively large proportion of aggregate BC. The average effective densities of 100-400 nm particles ranged from 1.35 to 1.51 g cm-3 with OC and inorganic salts as dominant components. Both density distribution and single-particle mass spectrometry showed more complex mixing states in larger particles. Upon heating, the separation of the effective density distribution modes confirmed the external mixing state of less-volatile BC or soot and potassium salts. The size-resolved optical properties of biomass burning particles were investigated at two wavelengths (λ = 450 and 530 nm). The single-scattering albedo (SSA) showed the lowest value for 50 nm particles (0.741 ± 0.007 and 0.889 ± 0.006) because of the larger proportion of BC content. Brown carbon played an important role for the SSA of 100-400 nm particles. The Ångström absorption exponent (AAE) values for all particles were above 1.6, indicating the significant presence of brown carbon in all sizes. Concurrent measurements in our work provide a basis for discussing the physicochemical properties of biomass burning aerosol and its effects on the global climate and atmospheric environment.

Effect of graphite particle size and content on the formation mechanism of detonation polycrystalline diamond

NASA Astrophysics Data System (ADS)

Tong, Y.; Cao, Y.; Liu, R.; Shang, S. Y.; Huang, F. L.

2018-03-01

The formation mechanism of detonation polycrystalline diamond (DPD) generated from the detonation of a mixed RDX/graphite explosive is investigated. It is found experimentally that the DPD conversion rate decreases with both the content and the particle size of the graphite. Moreover, the particle sizes of the generated DPD powder are analyzed, which shows that, with the decrease in the graphite particle size, the mean number diameter of DPD decreases, but the mean volume diameter increases. In addition, with the help of scanning electron microscopy, it is observed that the in situ phase change occurs in the graphite particles, by which the small particles combine to form numerous large DPD particles. Based on both the experimental data and the classical ZND detonation model, we divide such a DPD synthesis process into two stages: In the first stage, the in situ phase change from graphite to diamond is dominant, supplemented by some coalescence growth at high pressure and temperature, which is affected mainly by the detonation performance of the mixed explosive under consideration. In the second stage, the graphitization of DPD caused by the residual heat is dominant, which is affected mainly by the unloading rate of the particle temperature.

Mesoporous zirconium titanium oxides. Part 2: Synthesis, porosity, and adsorption properties of beads.

PubMed

Sizgek, G Devlet; Sizgek, Erden; Griffith, Christopher S; Luca, Vittorio

2008-11-04

Mesoporous zirconium titanium mixed-oxide beads having disordered wormhole textures and mole fractions of Zr (x) ranging from x=0.25 to 0.67 have been prepared. The bead preparation method combined the forced hydrolysis of mixtures of zirconium-titanium alkoxides in the presence of long-chain carboxylates with external gelation. Uniformly sized beads could be produced in the size range 0.5-1.1 mm by varying the droplet size and viscosity of the mixed-oxide sol, thus making them suitable for large-scale column chromatographic applications. The beads exhibited narrow pore size distributions with similar mean pore diameters of around 3.7 nm. The specific surface areas of the beads were linked to the Zr mole fraction in the precursor solution and were generally greater than 350 m2/g for x=0.5. A combination of scanning transmission electron microscopy and X-ray absorption fine structure analysis indicated that the pore walls of the beads were composed of atomically dispersed Zr and Ti to form a continuous network of Zr-O-Ti bonds. Mass transport in the beads was evaluated by monitoring the kinetics of vanadate and vanadyl adsorption at pH 10.5 and 0.87, respectively.

Structure and dynamics of mixed-species flocks in a Hawaiian rain forest

USGS Publications Warehouse

Hart, P.J.; Freed, L.A.

2003-01-01

Mixed-species flocks of native and introduced birds were studied for four years in an upper elevation Hawaiian rain forest. Those flocks were characterized by strong seasonality, large size, low species richness, high intraspecific abundance, a lack of migrants, and a general lack of territoriality or any sort of dominance hierarchy. There was high variability among years in patterns of occurrence at the species level, and high variability within years at the individual level. These flocks are loosely structured social groupings with apparently open membership. The fluid, unstable movement patterns, high degree of variability in size and composition, and lack of positive interspecific associations are not consistent with the “foraging enhancement” hypothesis for flocking. Two resident, endangered insectivores, the Akepa (Loxops coccineus) and Hawaii Creeper (Oreomystis mana) served as “nuclear” species. Flock composition was compared between two study sites that differed significantly in density of these two nuclear species. Flock size was similar at the two sites, primarily because the nuclear species were over-represented relative to their density. This observation suggests that birds are attempting to achieve a more optimal flock size at the lower density site.

The Diurnal Cycle of Particle Sizes, Compositions, and Densities observed in Sacramento, CA during CARES Field Campaign

NASA Astrophysics Data System (ADS)

Beránek, J.; Vaden, T.; Imre, D. G.; Zelenyuk, A.

2010-12-01

A central objective of the Carbonaceous Aerosol and Radiative Effects Study (CARES) was to characterize unequivocally all aspects related to organics in aerosols. To this end, a range of instruments measured loadings, size distributions, compositions, densities, CCN activities, and optical properties of aerosol sampled in Sacramento, CA over the month of June 2010. We present the results of measurements conducted by our single particle mass spectrometer, SPLAT. SPLAT was used to measure the size, composition, and density of individual particles with diameters between 50 to 2000 nm. SPLAT measured the vacuum aerodynamic diameters (dva) of more than 2 million particles and the compositions of ~350,000 particles, each day. In addition, SPLAT was used in combination with a differential mobility analyzer to measure the density, or effective density of individual particles. These measurements were typically conducted twice per day: in the morning, and mid-afternoon. Preliminary analysis of the data shows that under most conditions, the particles were relatively small (below 200 nm), and the vast majority of them were composed of oxygenated organics mixed with various amounts of sulfates. Analysis of the mass spectra shows that the oxygenated organics in these particles are the oxidized products of biogenic volatile organic precursors. In addition to particles composed of SOA mixed with sulfates, we detected and characterized fresh and processed soot particles, biomass burning aerosol, organic amines, sea salt - fresh and processed - and a small number of dust and other inorganic particles, commonly found in urban environment. SOA mixed with sulfates were the vast majority of particles at all times, while the other particle types exhibited episodic behavior. The data shows a reproducible diurnal pattern in SOA size distributions, number concentrations, and compositions. Early in the morning the particle number concentrations are relatively low, and the particle size distributions peak at ~70 nm. Smaller particles (80 nm) have a density of 1.3 g cm<-3/sup>, while the density of larger particles (200 nm) is 1.6 g cm<-3/sup>. The mass spectra show that the smaller particles are composed of organics mixed with ~10% of sulfates and larger ones contain mostly sulfate with a small amount of organics. As biogenic emissions are processed, nucleation events lead to a large increase in the concentrations of very small particles. As the day progresses particle number concentrations increase and particles grow. By mid-afternoon, these particles are sufficiently large to be characterized by SPLAT. At this point, the density of 80 to 200 nm particles is ~1.3 g cm<-3/sup>. These particles are composed of oxygenated organics mixed with a ~10% sulfate. A detailed analysis of the mass spectra shows that there are two types of SOA particles, which we labeled Type 43 and Type 44, to indicate which of the two peaks caries more intensity in the individual particle mass spectra. Interestingly, we find evidence to suggest that in both particle types a large fraction of the intensity in peaks 44 and 73 is related to surface compound.

Nearshore dynamics of artificial sand and oil agglomerates

USGS Publications Warehouse

Dalyander, P. Soupy; Plant, Nathaniel G.; Long, Joseph W.; McLaughlin, Molly R.

2015-01-01

Weathered oil can mix with sediment to form heavier-than-water sand and oil agglomerates (SOAs) that can cause beach re-oiling for years after a spill. Few studies have focused on the physical dynamics of SOAs. In this study, artificial SOAs (aSOAs) were created and deployed in the nearshore, and shear stress-based mobility formulations were assessed to predict SOA response. Prediction sensitivity to uncertainty in hydrodynamic conditions and shear stress parameterizations were explored. Critical stress estimates accounting for large particle exposure in a mixed bed gave the best predictions of mobility under shoaling and breaking waves. In the surf zone, the 10-cm aSOA was immobile and began to bury in the seafloor while smaller size classes dispersed alongshore. aSOAs up to 5 cm in diameter were frequently mobilized in the swash zone. The uncertainty in predicting aSOA dynamics reflects a broader uncertainty in applying mobility and transport formulations to cm-sized particles.

Using large eddy simulations to reveal the size, strength, and phase of updraft and downdraft cores of an Arctic mixed-phase stratocumulus cloud

DOE PAGES

Roesler, Erika L.; Posselt, Derek J.; Rood, Richard B.

2017-04-06

Three-dimensional large eddy simulations (LES) are used to analyze a springtime Arctic mixed-phase stratocumulus observed on 26 April 2008 during the Indirect and Semi-Direct Aerosol Campaign. Two subgrid-scale turbulence parameterizations are compared. The first scheme is a 1.5-order turbulent kinetic energy (1.5-TKE) parameterization that has been previously applied to boundary layer cloud simulations. The second scheme, Cloud Layers Unified By Binormals (CLUBB), provides higher-order turbulent closure with scale awareness. The simulations, in comparisons with observations, show that both schemes produce the liquid profiles within measurement variability but underpredict ice water mass and overpredict ice number concentration. The simulation using CLUBBmore » underpredicted liquid water path more than the simulation using the 1.5-TKE scheme, so the turbulent length scale and horizontal grid box size were increased to increase liquid water path and reduce dissipative energy. The LES simulations show this stratocumulus cloud to maintain a closed cellular structure, similar to observations. The updraft and downdraft cores self-organize into a larger meso-γ-scale convective pattern with the 1.5-TKE scheme, but the cores remain more isotropic with the CLUBB scheme. Additionally, the cores are often composed of liquid and ice instead of exclusively containing one or the other. Furthermore, these results provide insight into traditionally unresolved and unmeasurable aspects of an Arctic mixed-phase cloud. From analysis, this cloud's updraft and downdraft cores appear smaller than other closed-cell stratocumulus such as midlatitude stratocumulus and Arctic autumnal mixed-phase stratocumulus due to the weaker downdrafts and lower precipitation rates.« less

JPRS Report China.

DTIC Science & Technology

1988-07-29

adequate play to the leverage of wages. Reforms of the enterprise mechanism causes very differ- ent benefits for an enterprise which has implemented... benefits received by the same enterprises before and after contracting also differ greatly. Citing as an example 110 large- and medium-sized...was that it only looked into single benefits , causing an irrational enterprise organizational structure, rigidi- fication of the product mix, and

Experiments on water/melt explosions, nature of products, and models of dispersal

NASA Technical Reports Server (NTRS)

Sheridan, M. F.; Wohletz, K. H.

1984-01-01

Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

The Effect of a Dissipative Ladle Shroud on Mixing in Tundish: Mathematical and Experimental Modelling

NASA Astrophysics Data System (ADS)

Zhang, Jiangshan; Yang, Shufeng; Li, Jingshe; Tang, Haiyan; Jiang, Zhengyi

2018-01-01

The effect of a dissipative ladle shroud (DLS) on mixing in tundish was investigated, compared with that of a conventional ladle shroud (CLS) using mathematical and physical modelling. The tracer profiles of mathematical results, achieved using large eddy simulation, were validated by physical observations employing high-speed cinephotography. The design of a DLS dramatically changed the flow patterns and contributed the intermixing of fluid elements inside the ladle shroud. The vortex flow encouraged the turbulent mixing and was verified by tracking of physical tracer dispersion inside the DLS. Residence Time Distribution (RTD) curves were obtained in two different sized tundishes to examine the mixing behaviours. The findings indicated that the DLS benefited the tundish mixing in terms of increasing active volume. The effect seemed to be more remarkable in the smaller tundish. The DLS gave rise to a more plug-like flow pattern inside the tundish, showing potential to shorten the transition length during grade change.

Productivity growth, case mix and optimal size of hospitals. A 16-year study of the Norwegian hospital sector.

PubMed

Anthun, Kjartan Sarheim; Kittelsen, Sverre Andreas Campbell; Magnussen, Jon

2017-04-01

This paper analyses productivity growth in the Norwegian hospital sector over a period of 16 years, 1999-2014. This period was characterized by a large ownership reform with subsequent hospital reorganizations and mergers. We describe how technological change, technical productivity, scale efficiency and the estimated optimal size of hospitals have evolved during this period. Hospital admissions were grouped into diagnosis-related groups using a fixed-grouper logic. Four composite outputs were defined and inputs were measured as operating costs. Productivity and efficiency were estimated with bootstrapped data envelopment analyses. Mean productivity increased by 24.6% points from 1999 to 2014, an average annual change of 1.5%. There was a substantial growth in productivity and hospital size following the ownership reform. After the reform (2003-2014), average annual growth was <0.5%. There was no evidence of technical change. Estimated optimal size was smaller than the actual size of most hospitals, yet scale efficiency was high even after hospital mergers. However, the later hospital mergers have not been followed by similar productivity growth as around time of the reform. This study addresses the issues of both cross-sectional and longitudinal comparability of case mix between hospitals, and thus provides a framework for future studies. The study adds to the discussion on optimal hospital size. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of deformation induced nucleation and phase mixing, a two phase model for the ductile deformation of rocks.

NASA Astrophysics Data System (ADS)

Bevillard, Benoit; Richard, Guillaume; Raimbourg, Hugues

2017-04-01

Rocks are complex materials and particularly their rheological behavior under geological stresses remains a long-standing question in geodynamics. To test large scale lithosphere dynamics numerical modeling is the main tool but encounter substantial difficulties to account for this complexity. One major unknown is the origin and development of the localization of deformation. This localization is observed within a large range of scales and is commonly characterized by sharp grain size reduction. These considerations argues for a control of the microscopical scale over the largest ones through one predominant variable: the mean grain-size. However, the presence of second phase and broad grain-size distribution may also have a important impact on this phenomenon. To address this question, we built a model for ductile rocks deformation based on the two-phase damage theory of Bercovici & Ricard 2012. We aim to investigate the role of grain-size reduction but also phase mixing on strain localization. Instead of considering a Zener-pining effect on damage evolution, we propose to take into account the effect of the grain-boundary sliding (GBS)-induced nucleation mechanism which is better supported by experimental or natural observations (Precigout et al 2016). This continuum theory allows to represent a two mineral phases aggregate with explicit log-normal grain-size distribution as a reasonable approximation for polymineralic rocks. Quantifying microscopical variables using a statistical approach may allow for calibration at small (experimental) scale. The general set of evolutions equations remains up-scalable provided some conditions on the homogenization scale. Using the interface density as a measure of mixture quality, we assume unlike Bercovici & Ricard 2012 that it may depend for some part on grain-size . The grain-size independent part of it is being represented by a "contact fraction" variable, whose evolution may be constrained by the dominant deformation mechanism. To derive the related evolution equations and account for the interdependence of thermodynamic state variables, we use Onsager's thermodynamic extremum principle. Eventually, we solve for our set of equations using an Anorthite/Pyroxene gabbroic composition. The results are used to discuss the interaction between grain-size reduction and phase mixing on strain localization on several simple cases. Bercovici D, Ricard Y (2012) Mechanisms for the generation of plate tectonics by two phase grain damage and pinning. Physics of the Earth and Planetary Interiors 202-203:27-55 Precigout J, Stunitz H (2016) Evidence of phase nucleation during olivine diffusion creep: A new perspective for mantle strain localisation. Earth and Planetary Science Letters 405:94-105

NASA Multipoint LDI Development

NASA Technical Reports Server (NTRS)

Tacina, Robert

2001-01-01

Multipoint Lean-Direct-Injection (LDI) is a combustor concept in which a large number of fuel injectors and fuel-air mixers are used to quickly and uniformly mix the fuel and air so that ultralow levels of NO, are produced. Each fuel injector has an air swirler associated with it for fuel-air mixing and to establish a small recirculation and burning zone. A concept in which there are 36 fuel injectors in the space of a conventional single fuel injector has been tested in a flame tube. A greater than 80 percent reduction in NO, at high power conditions (400 psia, 1000 "Finlet) was achieved. Alternate concepts with 9,25,36 or 49 fuel injectors are being investigated in flame tube tests for their low NO, potential and with fuel staging to improve the turn-down ratio at low power conditions. A preliminary sector concept of a large engine design has been successfully tested at inlet conditions of 700 psia and 1100 O F . This concept had one half the number of fuel injectors per square inch as the flame tube configuration with 36 fuel injectors, and the NO, reduction was 65 percent of the ICAO standard. Future regional engine size sector tests are planned for the 2nd quarter of FY02 and large engine size sector tests for the 1st quarter of FY03.

The choice of sample size: a mixed Bayesian / frequentist approach.

PubMed

Pezeshk, Hamid; Nematollahi, Nader; Maroufy, Vahed; Gittins, John

2009-04-01

Sample size computations are largely based on frequentist or classical methods. In the Bayesian approach the prior information on the unknown parameters is taken into account. In this work we consider a fully Bayesian approach to the sample size determination problem which was introduced by Grundy et al. and developed by Lindley. This approach treats the problem as a decision problem and employs a utility function to find the optimal sample size of a trial. Furthermore, we assume that a regulatory authority, which is deciding on whether or not to grant a licence to a new treatment, uses a frequentist approach. We then find the optimal sample size for the trial by maximising the expected net benefit, which is the expected benefit of subsequent use of the new treatment minus the cost of the trial.

Observations of coarse sediment movements on the mixed beach of the Elwha Delta, Washington

USGS Publications Warehouse

Miller, I.M.; Warrick, J.A.; Morgan, C.

2011-01-01

Mixed beaches, with poorly sorted grains of multiple sizes, are a common and globally distributed shoreline type. Despite this, rates and mechanisms of sediment transport on mixed beaches are poorly understood. A series of tracer deployments using native clasts implanted with Radio Frequency Identifier (RFID) tags was used to develop a better understanding of sediment transport directions and magnitudes on the mixed grain-size beach of the Elwha River delta. Using tracer samples selected to match the distribution of the coarse fraction on the beach we find that all grain sizes, up to large cobbles (128-256 mm), were mobile under most measured wave conditions and move in relationship to the direction of the alongshore component of wave energy as estimated by incident breaking wave angles. In locations where the breaking wave is normal to the shoreline we find that tracers move in both alongshore directions with approximately equal frequency. In locations where breaking waves are oblique to the shoreline we find that alongshore transport is more unidirectional and tracers can approach average velocities of 100. m/day under winter wave conditions. We use the tracer cloud to estimate the beach active width, the mobile layer depth and sediment velocity. Our results suggest that, while sediment velocity increases under increased incident wave angles, the active layer depth and width decrease, reducing sediment flux at the site with the more oblique breaking waves. This result is contrary to what is suggested by traditional wave energy transport models of alongshore sediment transport. ?? 2011 Elsevier B.V.

Large-Scale Hybrid Motor Testing. Chapter 10

NASA Technical Reports Server (NTRS)

Story, George

2006-01-01

Hybrid rocket motors can be successfully demonstrated at a small scale virtually anywhere. There have been many suitcase sized portable test stands assembled for demonstration of hybrids. They show the safety of hybrid rockets to the audiences. These small show motors and small laboratory scale motors can give comparative burn rate data for development of different fuel/oxidizer combinations, however questions that are always asked when hybrids are mentioned for large scale applications are - how do they scale and has it been shown in a large motor? To answer those questions, large scale motor testing is required to verify the hybrid motor at its true size. The necessity to conduct large-scale hybrid rocket motor tests to validate the burn rate from the small motors to application size has been documented in several place^'^^.^. Comparison of small scale hybrid data to that of larger scale data indicates that the fuel burn rate goes down with increasing port size, even with the same oxidizer flux. This trend holds for conventional hybrid motors with forward oxidizer injection and HTPB based fuels. While the reason this is occurring would make a great paper or study or thesis, it is not thoroughly understood at this time. Potential causes include the fact that since hybrid combustion is boundary layer driven, the larger port sizes reduce the interaction (radiation, mixing and heat transfer) from the core region of the port. This chapter focuses on some of the large, prototype sized testing of hybrid motors. The largest motors tested have been AMROC s 250K-lbf thrust motor at Edwards Air Force Base and the Hybrid Propulsion Demonstration Program s 250K-lbf thrust motor at Stennis Space Center. Numerous smaller tests were performed to support the burn rate, stability and scaling concepts that went into the development of those large motors.

Mesoporous Akaganeite of Adjustable Pore Size Synthesized using Mixed Templates

NASA Astrophysics Data System (ADS)

Zhang, Y.; Ge, D. L.; Ren, H. P.; Fan, Y. J.; Wu, L. M.; Sun, Z. X.

2017-12-01

Mesoporous akaganeite with large and adjustable pore size was synthesized through a co-template method, which was achieved by the combined interaction between PEG2000 and alkyl amines with different lengths of the straight carbon chain. The characterized results indicate that the synthesized samples show comparatively narrow BJH pore size distributions and centered at 14.3 nm when PEG and HEPA was used, and it could be enlarged to 16.8 and 19.4 nm respectively through changing the alkyl amines to DDA and HDA. Meanwhile, all the synthesized akaganeite possess relativity high specific surface area ranging from 183 to 281 m2/g and high total pore volume of 0.98 to 1.5 cm3/g. A possible mechanism leading to the pore size changing was also proposed.

A giant testicular mixed germ cell tumour.

PubMed

Reekhaye, A; Harris, A; Nagarajan, S; Chadwick, D

2016-11-01

We present a case that we believe to be the largest mixed germ cell testicular tumour reported in the United Kingdom. A 23-year-old male was admitted to our urology department with a large scrotal swelling. The patient was found to have a giant left testicular tumour and a solitary lung metastasis at presentation. He underwent an emergency radical orchidectomy and subsequently received four cycles of bleomycin, etoposide and cisplatin chemotherapy. Four months after starting treatment, the tumour markers had normalised and a repeat staging computed tomography showed no active disease. The tumour reached that size because of the patient's failure to seek medical attention due to fear and embarrassment.

Characterization of re-grown floc size and structure: effect of mixing conditions during floc growth, breakage and re-growth process.

PubMed

Nan, Jun; Wang, Zhenbei; Yao, Meng; Yang, Yueming; Zhang, Xiaofei

2016-12-01

The impact of mixing speed in three stages-before breakage, during breakage, and after breakage-on re-grown floc properties was investigated by using a non-intrusive optical sampling and digital image analysis technique, respectively. And then, on the basis of different influence extent of mixing speed during each stage on size and structure of re-grown flocs, coagulation performance with varying mixing speed was analyzed. The results indicated that the broken flocs could not re-grow to the size before breakage in all cases. Furthermore, increasing mixing intensity contributed to the re-formation of smaller flocs with higher degree of compactness. For slow mixing before breakage, an increase in mixing speed had less influence on re-grown floc properties due to the same breakage strength during breakage, resulting in inconspicuous variation of coagulation efficiency. For rapid mixing during breakage, larger mixing speed markedly decreased the coagulation efficiency. This could be attributed that mixing speed during breakage generated greater influence on re-grown floc size. However, as slow mixing after breakage was elevated, the coagulation efficiency presented significant rise, indicating that slow mixing after breakage had more influence on re-grown floc structure upon re-structuring and re-arrangement mechanism.

Aggregate Size and Architecture Determine Microbial Activity Balance for One-Stage Partial Nitritation and Anammox ▿

PubMed Central

Vlaeminck, Siegfried E.; Terada, Akihiko; Smets, Barth F.; De Clippeleir, Haydée; Schaubroeck, Thomas; Bolca, Selin; Demeestere, Lien; Mast, Jan; Boon, Nico; Carballa, Marta; Verstraete, Willy

2010-01-01

Aerobic ammonium-oxidizing bacteria (AerAOB) and anoxic ammonium-oxidizing bacteria (AnAOB) cooperate in partial nitritation/anammox systems to remove ammonium from wastewater. In this process, large granular microbial aggregates enhance the performance, but little is known about granulation so far. In this study, three suspended-growth oxygen-limited autotrophic nitrification-denitrification (OLAND) reactors with different inoculation and operation (mixing and aeration) conditions, designated reactors A, B, and C, were used. The test objectives were (i) to quantify the AerAOB and AnAOB abundance and the activity balance for the different aggregate sizes and (ii) to relate aggregate morphology, size distribution, and architecture putatively to the inoculation and operation of the three reactors. A nitrite accumulation rate ratio (NARR) was defined as the net aerobic nitrite production rate divided by the anoxic nitrite consumption rate. The smallest reactor A, B, and C aggregates were nitrite sources (NARR, >1.7). Large reactor A and C aggregates were granules capable of autonomous nitrogen removal (NARR, 0.6 to 1.1) with internal AnAOB zones surrounded by an AerAOB rim. Around 50% of the autotrophic space in these granules consisted of AerAOB- and AnAOB-specific extracellular polymeric substances. Large reactor B aggregates were thin film-like nitrite sinks (NARR, <0.5) in which AnAOB were not shielded by an AerAOB layer. Voids and channels occupied 13 to 17% of the anoxic zone of AnAOB-rich aggregates (reactors B and C). The hypothesized granulation pathways include granule replication by division and budding and are driven by growth and/or decay based on species-specific physiology and by hydrodynamic shear and mixing. PMID:19948857

A simulation analysis to characterize the dynamics of vaccinating behaviour on contact networks.

PubMed

Perisic, Ana; Bauch, Chris T

2009-05-28

Human behavior influences infectious disease transmission, and numerous "prevalence-behavior" models have analyzed this interplay. These previous analyses assumed homogeneously mixing populations without spatial or social structure. However, spatial and social heterogeneity are known to significantly impact transmission dynamics and are particularly relevant for certain diseases. Previous work has demonstrated that social contact structure can change the individual incentive to vaccinate, thus enabling eradication of a disease under a voluntary vaccination policy when the corresponding homogeneous mixing model predicts that eradication is impossible due to free rider effects. Here, we extend this work and characterize the range of possible behavior-prevalence dynamics on a network. We simulate transmission of a vaccine-preventable infection through a random, static contact network. Individuals choose whether or not to vaccinate on any given day according to perceived risks of vaccination and infection. We find three possible outcomes for behavior-prevalence dynamics on this type of network: small final number vaccinated and final epidemic size (due to rapid control through voluntary ring vaccination); large final number vaccinated and significant final epidemic size (due to imperfect voluntary ring vaccination), and little or no vaccination and large final epidemic size (corresponding to little or no voluntary ring vaccination). We also show that the social contact structure enables eradication under a broad range of assumptions, except when vaccine risk is sufficiently high, the disease risk is sufficiently low, or individuals vaccinate too late for the vaccine to be effective. For populations where infection can spread only through social contact network, relatively small differences in parameter values relating to perceived risk or vaccination behavior at the individual level can translate into large differences in population-level outcomes such as final size and final number vaccinated. The qualitative outcome of rational, self interested behaviour under a voluntary vaccination policy can vary substantially depending on interactions between social contact structure, perceived vaccine and disease risks, and the way that individual vaccination decision-making is modelled.

Examining the relationship between social support availability, urban center size, and self-perceived mental health of recent immigrants to Canada: a mixed-methods analysis.

PubMed

Chadwick, Kathryn A; Collins, Patricia A

2015-03-01

The experiences of settlement in a new country (e.g., securing housing and employment, language barriers) pose numerous challenges for recent immigrants that can impede their health and well-being. Lack of social support upon arrival and during settlement may help to explain why immigrant mental health status declines over time. While most urban centers in Canada offer some settlement services, little is known about how the availability of social supports, and the health statuses of recent immigrants, varies by city size. The objective of this mixed-methods study was to examine the relationship between self-perceived mental health (SPMH), social support availability, and urban center size, for recent immigrants to Canada. The quantitative component involved analysis of 2009-2010 Canadian Community Health Survey data, selecting for only recent immigrants and for those living in either large or small urban centers. The qualitative component involved in-depth interviews with managers of settlement service organizations located in three large and three small urban centers in Canada. The quantitative analysis revealed that social support availability is positively associated with higher SPMH status, and is higher in small urban centers. In support of these findings, our interviews revealed that settlement service organizations operating in small urban centers offer more intensive social supports; interviewees attributed this difference to personal relationships in small cities, and the ease with which they can connect to other agencies to provide clients with necessary supports. Logistic regression analysis revealed, however, that recent immigrants in small urban centers are twice as likely to report low SPMH compared to those living in large urban centers. Thus, while the scope and nature of settlements services appears to vary by city size in Canada, more research is needed to understand what effect settlement services have on the health status of recent immigrants to Canada, especially in smaller urban centers. Copyright © 2015. Published by Elsevier Ltd.

A simulation analysis to characterize the dynamics of vaccinating behaviour on contact networks

PubMed Central

2009-01-01

Background Human behavior influences infectious disease transmission, and numerous "prevalence-behavior" models have analyzed this interplay. These previous analyses assumed homogeneously mixing populations without spatial or social structure. However, spatial and social heterogeneity are known to significantly impact transmission dynamics and are particularly relevant for certain diseases. Previous work has demonstrated that social contact structure can change the individual incentive to vaccinate, thus enabling eradication of a disease under a voluntary vaccination policy when the corresponding homogeneous mixing model predicts that eradication is impossible due to free rider effects. Here, we extend this work and characterize the range of possible behavior-prevalence dynamics on a network. Methods We simulate transmission of a vaccine-prevetable infection through a random, static contact network. Individuals choose whether or not to vaccinate on any given day according to perceived risks of vaccination and infection. Results We find three possible outcomes for behavior-prevalence dynamics on this type of network: small final number vaccinated and final epidemic size (due to rapid control through voluntary ring vaccination); large final number vaccinated and significant final epidemic size (due to imperfect voluntary ring vaccination), and little or no vaccination and large final epidemic size (corresponding to little or no voluntary ring vaccination). We also show that the social contact structure enables eradication under a broad range of assumptions, except when vaccine risk is sufficiently high, the disease risk is sufficiently low, or individuals vaccinate too late for the vaccine to be effective. Conclusion For populations where infection can spread only through social contact network, relatively small differences in parameter values relating to perceived risk or vaccination behavior at the individual level can translate into large differences in population-level outcomes such as final size and final number vaccinated. The qualitative outcome of rational, self interested behaviour under a voluntary vaccination policy can vary substantially depending on interactions between social contact structure, perceived vaccine and disease risks, and the way that individual vaccination decision-making is modelled. PMID:19476616

Fuel treatment effects on tree mortality following wildfire in dry mixed conifer forests, Washington State, USA

Treesearch

Susan J. Prichard; Maureen C. Kennedy

2012-01-01

Fuel reduction treatments are increasingly used to mitigate future wildfire severity in dry forests, but few opportunities exist to assess their effectiveness. We evaluated the influence of fuel treatment, tree size and species on tree mortality following a large wildfire event in recent thin-only, thin and prescribed burn (thin-Rx) units. Of the trees that died within...

Lipid globule size in total nutrient admixtures prepared in three-chamber plastic bags.

PubMed

Driscoll, David F; Thoma, Andrea; Franke, Rolf; Klütsch, Karsten; Nehne, Jörg; Bistrian, Bruce R

2009-04-01

The stability of injectable lipid emulsions in three-chamber plastic (3CP) bags, applying the globule-size limits established by United States Pharmacopeia ( USP ) chapter 729, was studied. A total of five premixed total nutrient admixture (TNA) products packaged in 3CP bags from two different lipid manufacturers containing either 20% soybean oil or a mixture of soybean oil and medium-chain-triglyceride oil as injectable lipid emulsions were tested. Two low-osmolarity 3CP bags and three high-osmolarity 3CP bags were studied. All products were tested with the addition of trace elements and multivitamins. All additive conditions (with and without electrolytes) were tested in triplicate at time 0 (immediately after mixing) and at 6, 24, 30, and 48 hours after mixing; the bags were stored at 24-26 degrees C. All additives were equally distributed in each bag for comparative testing, applying both globule sizing methods outlined in USP chapter 729. Of the bags tested, all bags from one manufacturer were coarse emulsions, showing signs of significant growth in the large-diameter tail when mixed as a TNA formulation and failing the limits set by method II of USP chapter 729 from the outset and throughout the study, while the bags from the other manufacturer were fine emulsions and met these limits. Of the bags that failed, significant instability was noted in one series containing additional electrolytes. Injectable lipid emulsions provided in 3CP bags that did not meet the globule-size limits of USP chapter 729 produced coarser TNA formulations than emulsions that met the USP limits.

Preparation of uniform nanoparticles of ultra-high purity metal oxides, mixed metal oxides, metals, and metal alloys

DOEpatents

Woodfield, Brian F.; Liu, Shengfeng; Boerio-Goates, Juliana; Liu, Qingyuan; Smith, Stacey Janel

2012-07-03

In preferred embodiments, metal nanoparticles, mixed-metal (alloy) nanoparticles, metal oxide nanoparticles and mixed-metal oxide nanoparticles are provided. According to embodiments, the nanoparticles may possess narrow size distributions and high purities. In certain preferred embodiments, methods of preparing metal nanoparticles, mixed-metal nanoparticles, metal oxide nanoparticles and mixed-metal nanoparticles are provided. These methods may provide tight control of particle size, size distribution, and oxidation state. Other preferred embodiments relate to a precursor material that may be used to form nanoparticles. In addition, products prepared from such nanoparticles are disclosed.

Protein Production Through Microbial Conversion of Rice Straw by Multi-Strain Fermentation.

PubMed

Jia, Jinru; Chen, Huayou; Wu, Bangguo; Cui, Fengjie; Fang, Hua; Wang, Hongcheng; Ni, Zhong

2018-06-20

Multi-strain mixed fermentation can provide a relatively complete lignocellulosic enzyme system compared with single-strain fermentation. This study was firstly to screen strains which have a strong ability to hydrolyse rice straw (RS) enzymatically and enrich true protein (TP). Then, the conditions in the process of SSF, including the optimum inoculum size of mixed strains, inoculation ratio, and different inoculation time of N. crassa 14-8, were optimized. The experimental results showed that the highest TP content could be obtained by using N. crassa 14-8, C. utilis, and P. chrysosporium as mixed strains, and 5 mM Mn 2+ and 50 mM veratryl alcohol were used as inducers of lignin peroxidase (LiP) to improve the efficiency of enzymatic hydrolysis. When N. crassa 14-8 was inoculated 1 day later than P. chrysosporium, the total inoculum size was 10%, and the optimum ratio of N. crassa 14-8 to P. chrysosporium was 1:2, the maximum TP yield (8.89%) was obtained, with 123.37% of its increase rate. This work proposed a technique with potential application in large-scale feedstuff protein conversion.

Uniformly Dispersed and Re-Agglomerated Graphene Oxide-Based Cement Pastes: A Comparison of Rheological Properties, Mechanical Properties and Microstructure.

PubMed

Long, Wu-Jian; Li, Hao-Dao; Fang, Chang-Le; Xing, Feng

2018-01-09

The properties of graphene oxide (GO)-based cement paste can be significantly affected by the state of GO dispersion. In this study, the effects of uniformly dispersed and re-agglomerated GO on the rheological, mechanical properties and microstructure of cement paste were systematically investigated. Two distinct dispersion states can be achieved by altering the mixing sequence: Polycarboxylate-ether (PCE) mixed with GO-cement or cement mixed with GO-PCE. The experimental results showed that the yield stress and plastic viscosity increased with the uniformly dispersed GO when compared to those of re-agglomerated GO cement paste. Moreover, the 3-day compressive and flexural strengths of uniformly dispersed GO paste were 8% and 27%, respectively, higher than those of re-agglomerated GO pastes. The results of X-ray diffraction, Fourier transform infrared spectroscopy and scanning electron microscopy analyses demonstrated that uniformly dispersed GO more effectively promotes the formation of hydration products in hardened cement paste. Furthermore, a porosity analysis using mercury intrusion porosimetry revealed that the homogeneous dispersion of GO can better inhibit the formation of large-size pores and optimize the pore size distribution at 3 and 7 days than the re-agglomerated GO.

Ejecta from Ocean Impacts

NASA Technical Reports Server (NTRS)

Kyte, Frank T.

2003-01-01

Numerical simulations of deep-ocean impact provide some limits on the size of a projectile that will not mix with the ocean floor during a deep-ocean impact. For a vertical impact at asteroidal velocities (approx. 20 km/s), mixing is only likely when the projectile diameter is greater than 112 of the water depth. For oblique impacts, even larger projectiles will not mix with ocean floor silicates. Given the typical water depths of 4 to 5 km in deep-ocean basins, asteroidal projectiles with diameters as large as 2 or 3 km may commonly produce silicate ejecta that is composed only of meteoritic materials and seawater salts. However, the compressed water column beneath the projectile can still disrupt and shock metamorphose the ocean floor. Therefore, production of a separate, terrestrial ejecta component is not ruled out in the most extreme case. With increasing projectile size (or energy) relative to water depths, there must be a gradation between oceanic impacts and more conventional continental impacts. Given that 60% of the Earth's surface is covered by oceanic lithosphere and 500 m projectiles impact the Earth on 10(exp 5) y timescales, there must be hundreds of oceanic impact deposits in the sediment record awaiting discovery.

Enhanced light absorption due to the mixing state of black carbon in fresh biomass burning emissions

NASA Astrophysics Data System (ADS)

Wang, Qiyuan; Cao, Junji; Han, Yongming; Tian, Jie; Zhang, Yue; Pongpiachan, Siwatt; Zhang, Yonggang; Li, Li; Niu, Xinyi; Shen, Zhenxing; Zhao, Zhuzi; Tipmanee, Danai; Bunsomboonsakul, Suratta; Chen, Yang; Sun, Jian

2018-05-01

A lack of information on the radiative effects of refractory black carbon (rBC) emitted from biomass burning is a significant gap in our understanding of climate change. A custom-made combustion chamber was used to simulate the open burning of crop residues and investigate the impacts of rBC size and mixing state on the particles' optical properties. Average rBC mass median diameters ranged from 141 to 162 nm for the rBC produced from different types of crop residues. The number fraction of thickly-coated rBC varied from 53 to 64%, suggesting that a majority of the freshly emitted rBC were internally mixed. By comparing the result of observed mass absorption cross-section to that calculated with Mie theory, large light absorption enhancement factors (1.7-1.9) were found for coated particles relative to uncoated cores. These effects were strongly positively correlated with the percentage of coated particles but independent of rBC core size. We suggest that rBC from open biomass burning may have strong impact on air pollution and radiative forcing immediately after their production.

Chefs' opinions of restaurant portion sizes.

PubMed

Condrasky, Marge; Ledikwe, Jenny H; Flood, Julie E; Rolls, Barbara J

2007-08-01

The objectives were to determine who establishes restaurant portion sizes and factors that influence these decisions, and to examine chefs' opinions regarding portion size, nutrition information, and weight management. A survey was distributed to chefs to obtain information about who is responsible for determining restaurant portion sizes, factors influencing restaurant portion sizes, what food portion sizes are being served in restaurants, and chefs' opinions regarding nutrition information, health, and body weight. The final sample consisted of 300 chefs attending various culinary meetings. Executive chefs were identified as being primarily responsible for establishing portion sizes served in restaurants. Factors reported to have a strong influence on restaurant portion sizes included presentation of foods, food cost, and customer expectations. While 76% of chefs thought that they served "regular" portions, the actual portions of steak and pasta they reported serving were 2 to 4 times larger than serving sizes recommended by the U.S government. Chefs indicated that they believe that the amount of food served influences how much patrons consume and that large portions are a problem for weight control, but their opinions were mixed regarding whether it is the customer's responsibility to eat an appropriate amount when served a large portion of food. Portion size is a key determinant of energy intake, and the results from this study suggest that cultural norms and economic value strongly influence the determination of restaurant portion sizes. Strategies are needed to encourage chefs to provide and promote portions that are appropriate for customers' energy requirements.

Spray droplet size, drift potential, and risks to nontarget organisms from aerially applied glyphosate for coca control in Colombia.

PubMed

Hewitt, Andrew J; Solomon, Keith R; Marshall, E J P

2009-01-01

A wind tunnel atomization study was conducted to measure the emission droplet size spectra for water and Glyphos (a glyphosate formulation sold in Colombia) + Cosmo-flux sprays for aerial application to control coca and poppy crops in Colombia. The droplet size spectra were measured in a wind tunnel for an Accu-Flo nozzle (with 16 size 0.085 [2.16 mm] orifices), under appropriate simulated aircraft speeds (up to 333 km/h), using a laser diffraction instrument covering a dynamic size range for droplets of 0.5 to 3,500 microm. The spray drift potential of the glyphosate was modeled using the AGDISP spray application and drift model, using input parameters representative of those occurring in Colombia for typical aerial application operations. The droplet size spectra for tank mixes containing glyphosate and Cosmo-Flux were considerably finer than water and became finer with higher aircraft speeds. The tank mix with 44% glyphosate had a D(v0.5) of 128 microm, while the value at the 4.9% glyphosate rate was 140 microm. These are classified as very fine to fine sprays. Despite being relatively fine, modeling showed that the droplets would not evaporate as rapidly as most similarly sized agricultural sprays because the nonvolatile proportion of the tank mix (active and inert adjuvant ingredients) was large. Thus, longer range drift is small and most drift that does occur will deposit relatively close to the application area. Drift will only occur downwind and, with winds of velocity less than the modeled maximum of 9 km/h, the drift distance would be substantially reduced. Spray drift potential might be additionally reduced through various practices such as the selection of nozzles, tank mix adjuvants, aircraft speeds, and spray pressures that would produce coarser sprays. Species sensitivity distributions to glyphosate were constructed for plants and amphibians. Based on modeled drift and 5th centile concentrations, appropriate no-spray buffer zones (distance from the end of the spray boom as recorded electronically +/-5%) for protection of sensitive plants were 50-120 m for coca spray scenarios and considerably lower for poppy spray scenarios. The equivalent buffer zone for amphibia was 5 m. The low toxicity of glyphosate to humans suggests that these aerial applications are not a concern for human health.

The LSST Camera 500 watt -130 degC Mixed Refrigerant Cooling System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowden, Gordon B.; Langton, Brian J.; /SLAC

2014-05-28

The LSST Camera has a higher cryogenic heat load than previous CCD telescope cameras due to its large size (634 mm diameter focal plane, 3.2 Giga pixels) and its close coupled front-end electronics operating at low temperature inside the cryostat. Various refrigeration technologies are considered for this telescope/camera environment. MMR-Technology’s Mixed Refrigerant technology was chosen. A collaboration with that company was started in 2009. The system, based on a cluster of Joule-Thomson refrigerators running a special blend of mixed refrigerants is described. Both the advantages and problems of applying this technology to telescope camera refrigeration are discussed. Test results frommore » a prototype refrigerator running in a realistic telescope configuration are reported. Current and future stages of the development program are described. (auth)« less

The impact of image-size manipulation and sugar content on children's cereal consumption.

PubMed

Neyens, E; Aerts, G; Smits, T

2015-12-01

Previous studies have demonstrated that portion sizes and food energy-density influence children's eating behavior. However, the potential effects of front-of-pack image-sizes of serving suggestions and sugar content have not been tested. Using a mixed experimental design among young children, this study examines the effects of image-size manipulation and sugar content on cereal and milk consumption. Children poured and consumed significantly more cereal and drank significantly more milk when exposed to a larger sized image of serving suggestion as compared to a smaller image-size. Sugar content showed no main effects. Nevertheless, cereal consumption only differed significantly between small and large image-sizes when sugar content was low. An advantage of this study was the mundane setting in which the data were collected: a school's dining room instead of an artificial lab. Future studies should include a control condition, with children eating by themselves to reflect an even more natural context. Copyright © 2015 Elsevier Ltd. All rights reserved.

mHealth Series: mHealth project in Zhao County, rural China – Description of objectives, field site and methods

PubMed Central

van Velthoven, Michelle Helena; Li, Ye; Wang, Wei; Du, Xiaozhen; Wu, Qiong; Chen, Li; Majeed, Azeem; Rudan, Igor; Zhang, Yanfeng; Car, Josip

2013-01-01

Background We set up a collaboration between researchers in China and the UK that aimed to explore the use of mHealth in China. This is the first paper in a series of papers on a large mHealth project part of this collaboration. This paper included the aims and objectives of the mHealth project, our field site, and the detailed methods of two studies. Field site The field site for this mHealth project was Zhao County, which lies 280 km south of Beijing in Hebei Province, China. Methods We described the methodology of two studies: (i) a mixed methods study exploring factors influencing sample size calculations for mHealth–based health surveys and (ii) a cross–over study determining validity of an mHealth text messaging data collection tool. The first study used mixed methods, both quantitative and qualitative, including: (i) two surveys with caregivers of young children, (ii) interviews with caregivers, village doctors and participants of the cross–over study, and (iii) researchers’ views. We combined data from caregivers, village doctors and researchers to provide an in–depth understanding of factors influencing sample size calculations for mHealth–based health surveys. The second study, a cross–over study, used a randomised cross–over study design to compare the traditional face–to–face survey method to the new text messaging survey method. We assessed data equivalence (intrarater agreement), the amount of information in responses, reasons for giving different responses, the response rate, characteristics of non–responders, and the error rate. Conclusions This paper described the objectives, field site and methods of a large mHealth project part of a collaboration between researchers in China and the UK. The mixed methods study evaluating factors that influence sample size calculations could help future studies with estimating reliable sample sizes. The cross–over study comparing face–to–face and text message survey data collection could help future studies with developing their mHealth tools. PMID:24363919

Size dependent exchange bias in single-phase Zn0.3Ni0.7Fe2O4 ferrite nanoparticles

NASA Astrophysics Data System (ADS)

Mohan, Rajendra; Ghosh, Mritunjoy Prasad; Mukherjee, Samrat

2018-07-01

We report the microstructural and magnetic characterization of single phase nanocrystalline partially inverted Zn0.3Ni0.7Fe2O4 mixed spinel ferrite. The samples were annealed at 200 °C, 400 °C, 600 °C, 800 °C and 1000 °C. X-ray diffraction results indicate phase purity of all the samples and application of Debye- Scherrer yielded a crystallite size variation from 5 nm to 33 nm for the different samples. Magnetic measurements have revealed the freezing of interfacial spins which were the cause of the large horizontal M-H loop shift causing large exchange bias with high anisotropy. The magnetic measurements show a hysteresis loop with high effective anisotropy constant due to highly magnetically disordered surface spin at 5 K.

Size and modal analyses of fines and ultrafines from some Apollo 17 samples

NASA Technical Reports Server (NTRS)

Greene, G. M.; King, D. T., Jr.; Banholzer, G. S., Jr.; King, E. A.

1975-01-01

Scanning electron and optical microscopy techniques have been used to determine the grain-size frequency distributions and morphology-based modal analyses of fine and ultrafine fractions of some Apollo 17 regolith samples. There are significant and large differences between the grain-size frequency distributions of the less than 10-micron size fraction of Apollo 17 samples, but there are no clear relations to the local geologic setting from which individual samples have been collected. This may be due to effective lateral mixing of regolith particles in this size range by micrometeoroid impacts. None of the properties of the frequency distributions support the idea of selective transport of any fine grain-size fraction, as has been proposed by other workers. All of the particle types found in the coarser size fractions also occur in the less than 10-micron particles. In the size range from 105 to 10 microns there is a strong tendency for the percentage of regularly shaped glass to increase as the graphic mean grain size of the less than 1-mm size fraction decreases, both probably being controlled by exposure age.

Primary and community care workforce planning and development.

PubMed

Hurst, Keith

2006-09-01

This article reports a study that provided primary and community care managers with information, allowing them to: (a) evaluate the size and mix of their workforce; and (b) develop knowledgeable and skilled teams to meet the demands of growing and changing services. Primary and community care services are growing in the United Kingdom, but workforce planning and development, despite their wide-ranging cost and quality implications, have not received the same attention. Indeed, most primary and community care workforce planning and development issues are universal. Demand 1-1 side workforce planning is concerned not only with the number, but also with staff mix; but how these autonomous and isolated practitioners spend their time is unique. The other side of the equation, workforce supply, raises many recruitment and retention challenges for managers in many countries. Any country's main workforce planning methods apply equally well to primary care, but each is flawed. A second, main problem is that the methods lead to fragmented services, whereas modern workforce planning methods should be multidisciplinary. Consequently, it has never been more important for managers to have data and algorithms to develop appropriate care teams. A large and versatile workforce database, profiling 304 English primary care trusts using demographic, socio-economic, mortality, morbidity, staffing and performance workforce-related variables, compiled in 2002 and updated yearly, is described. Data were supplemented with a systematic literature review leading to a 340-item annotated bibliography; and qualitative interviews with managers. Workforce size and mix are historical and irrational at best. Moreover, the number of variables that influence staffing is growing, thereby complicating workforce planning. Evaluating and adjusting the size and mix of teams using empirically determined community demand and performance variables based on the area's socio-economic characteristics is feasible.

Metamorphic reactions, grain size reduction and deformation of mafic lower crustal rocks

NASA Astrophysics Data System (ADS)

Degli Alessandrini, Giulia; Menegon, Luca; Beltrando, Marco; Dijkstra, Arjan; Anderson, Mark

2016-04-01

This study investigates grain-scale deformation mechanisms associated with strain localization in the mafic continental lower crust, with particular focus on the role of syn-kinematic metamorphic reactions and their product - symplectites - in promoting grain size reduction and phase mixing. The investigated shear zone is hosted in the Finero mafic-ultramafic complex in the Italian Southern Alps. Shearing occurred at T ≥ 650° C and P ≥ 0.4-0.6 GPa. The shear zone reworks both mafic and ultramafic lithologies and displays anastomosing patterns of (ultra)mylonitic high strain zones wrapping less foliated, weakly deformed low strain domains. Field and microstructural observations indicate that different compositional layers of the shear zone responded differently to deformation, resulting in strain partitioning. Four distinct microstructural domains have been identified: (1) an ultramylonitic domain characterized by an amph + pl matrix (grain size < 30μm) with large amphibole porphyroclasts (grain size between 200μm and 5000μm) and rare garnets; (2) a domain rich in garnet porphyroclasts embedded in a matrix of monomineralic plagioclase displaying a core and mantle structure (average grain size 45μm) (3) a metagabbroic domain with porphyroclasts of clinopyroxene, orthopyroxene and garnets (200μm average grain size) wrapped by monomineralic ribbons of recrystallized plagioclase and (4) a garnet-free ultramylonitic domain composed of an intermixed amph + cpx + opx + pl matrix (6μm average grain size). In these domains, each porphyroclastic mineral responds differently to deformation: amphibole readily breaks down to symplectitic intergrowths of amph + pl or opx + pl. Garnet undergoes fracturing (in domain 2) or reacts to give symplectites of pl + opx (in domain 3). Plagioclase dynamically recrystallizes in mono-phase aggregates, whereas clinopyroxene undergoes fracturing and orthopyroxene undergoes plastic deformation. The behaviour of the different phases and their relative abundance in the layers are believed to influence the deformation of the layers themselves. In symplectite-rich layers (domains 1, 4) deformation is localised, grain-size is below 30μm and phases are well mixed. On the other hand, in pyroxene or plagioclase-rich layers, deformation is less localised, the phases are less mixed and the grain size is larger (domain 2, 3). These preliminary results suggest that syn-kinematic metamorphic reactions forming symplectites played an essential role in grain size reduction, phase mixing and strain localization. We speculate that the compositional domains with symplectites localized deformation more efficiently, by activation of grain size sensitive creep, most likely because those domains were originally more hydrated than the others. On the contrary, domains without symplectites accommodated deformation less efficiently, either through fracturing (clinopyroxene, garnet) or dislocation creep + recrystallization (orthopyroxene, plagioclase).

Variability in morphology, hygroscopicity, and optical properties of soot aerosols during atmospheric processing

PubMed Central

Zhang, Renyi; Khalizov, Alexei F.; Pagels, Joakim; Zhang, Dan; Xue, Huaxin; McMurry, Peter H.

2008-01-01

The atmospheric effects of soot aerosols include interference with radiative transfer, visibility impairment, and alteration of cloud formation and are highly sensitive to the manner by which soot is internally mixed with other aerosol constituents. We present experimental studies to show that soot particles acquire a large mass fraction of sulfuric acid during atmospheric aging, considerably altering their properties. Soot particles exposed to subsaturated sulfuric acid vapor exhibit a marked change in morphology, characterized by a decreased mobility-based diameter but an increased fractal dimension and effective density. These particles experience large hygroscopic size and mass growth at subsaturated conditions (<90% relative humidity) and act efficiently as cloud-condensation nuclei. Coating with sulfuric acid and subsequent hygroscopic growth enhance the optical properties of soot aerosols, increasing scattering by ≈10-fold and absorption by nearly 2-fold at 80% relative humidity relative to fresh particles. In addition, condensation of sulfuric acid is shown to occur at a similar rate on ambient aerosols of various types of a given mobility size, regardless of their chemical compositions and microphysical structures. Representing an important mechanism of atmospheric aging, internal mixing of soot with sulfuric acid has profound implications on visibility, human health, and direct and indirect climate forcing. PMID:18645179

Sustainability of a Compartmentalized Host-Parasite Replicator System under Periodic Washout-Mixing Cycles

PubMed Central

Furubayashi, Taro

2018-01-01

The emergence and dominance of parasitic replicators are among the major hurdles for the proliferation of primitive replicators. Compartmentalization of replicators is proposed to relieve the parasite dominance; however, it remains unclear under what conditions simple compartmentalization uncoupled with internal reaction secures the long-term survival of a population of primitive replicators against incessant parasite emergence. Here, we investigate the sustainability of a compartmentalized host-parasite replicator (CHPR) system undergoing periodic washout-mixing cycles, by constructing a mathematical model and performing extensive simulations. We describe sustainable landscapes of the CHPR system in the parameter space and elucidate the mechanism of phase transitions between sustainable and extinct regions. Our findings revealed that a large population size of compartments, a high mixing intensity, and a modest amount of nutrients are important factors for the robust survival of replicators. We also found two distinctive sustainable phases with different mixing intensities. These results suggest that a population of simple host–parasite replicators assumed before the origin of life can be sustained by a simple compartmentalization with periodic washout-mixing processes. PMID:29373536

Pulse frequency and soil-litter mixing alter the control of cumulative precipitation over litter decomposition.

PubMed

Joly, François-Xavier; Kurupas, Kelsey L; Throop, Heather L

2017-09-01

Macroclimate has traditionally been considered the predominant driver of litter decomposition. However, in drylands, cumulative monthly or annual precipitation typically fails to predict decomposition. In these systems, the windows of opportunity for decomposer activity may rather depend on the precipitation frequency and local factors affecting litter desiccation, such as soil-litter mixing. We used a full-factorial microcosm experiment to disentangle the relative importance of cumulative precipitation, pulse frequency, and soil-litter mixing on litter decomposition. Decomposition, measured as litter carbon loss, saturated with increasing cumulative precipitation when pulses were large and infrequent, suggesting that litter moisture no longer increased and/or microbial activity was no longer limited by water availability above a certain pulse size. More frequent precipitation pulses led to increased decomposition at high levels of cumulative precipitation. Soil-litter mixing consistently increased decomposition, with greatest relative increase (+194%) under the driest conditions. Collectively, our results highlight the need to consider precipitation at finer temporal scale and incorporate soil-litter mixing as key driver of decomposition in drylands. © 2017 by the Ecological Society of America.

3D-Simulation Of Concentration Distributions Inside Large-Scale Circulating Fluidized Bed Combustors

NASA Astrophysics Data System (ADS)

Wischnewski, R.; Ratschow, L.; Hartge, E. U.; Werthe, J.

With increasing size of modern CFB combustors the lateral mixing of fuels and secondary air gains more and more importance. Strong concentration gradients, which result from improper lateral mixing, can lead to operational problems, high flue gas emissions and lower boiler efficiencies. A 3D-model for the simulation of local gas and solids concentrations inside industrial-sized CFB boilers has been developed. The model is based on a macroscopic approach and considers all major mechanisms during fuel spreading and subsequent combustion of char and volatiles. Typical characteristics of modern boilers like staged combustion, a smaller cross-sectional area in the lower section of the combustion chamber and the co-combustion of additional fuels with coal can be considered. The 252 MWth combustor of Stadtwerke Duisburg AG is used for the validation of the model. A comprehensive picture of the local conditions inside the combustion chamber is achieved by the combination of local gas measurements and the three-dimensional simulation of concentration distributions.

A new tool called DISSECT for analysing large genomic data sets using a Big Data approach

PubMed Central

Canela-Xandri, Oriol; Law, Andy; Gray, Alan; Woolliams, John A.; Tenesa, Albert

2015-01-01

Large-scale genetic and genomic data are increasingly available and the major bottleneck in their analysis is a lack of sufficiently scalable computational tools. To address this problem in the context of complex traits analysis, we present DISSECT. DISSECT is a new and freely available software that is able to exploit the distributed-memory parallel computational architectures of compute clusters, to perform a wide range of genomic and epidemiologic analyses, which currently can only be carried out on reduced sample sizes or under restricted conditions. We demonstrate the usefulness of our new tool by addressing the challenge of predicting phenotypes from genotype data in human populations using mixed-linear model analysis. We analyse simulated traits from 470,000 individuals genotyped for 590,004 SNPs in ∼4 h using the combined computational power of 8,400 processor cores. We find that prediction accuracies in excess of 80% of the theoretical maximum could be achieved with large sample sizes. PMID:26657010

Organic Condensation and Particle Growth to CCN Sizes in the Summertime Marine Arctic Is Driven by Materials More Semivolatile Than at Continental Sites

NASA Astrophysics Data System (ADS)

Burkart, Julia; Hodshire, Anna L.; Mungall, Emma L.; Pierce, Jeffrey R.; Collins, Douglas B.; Ladino, Luis A.; Lee, Alex K. Y.; Irish, Victoria; Wentzell, Jeremy J. B.; Liggio, John; Papakyriakou, Tim; Murphy, Jennifer; Abbatt, Jonathan

2017-10-01

Ship-based aerosol measurements in the summertime Arctic indicate elevated concentrations of ultrafine particles with occasional growth to cloud condensation nuclei (CCN) sizes. Focusing on one episode with two continuously growing modes, growth occurs faster for a large, preexisting mode (dp ≈ 90 nm) than for a smaller nucleation mode (dp ≈ 20 nm). We use microphysical modeling to show that growth is largely via organic condensation. Unlike results for midlatitude forested regions, most of these condensing species behave as semivolatile organics, as lower volatility organics would lead to faster growth of the smaller mode. The magnitude of the CCN hygroscopicity parameter for the growing particles, 0.1, is also consistent with organic species constituting a large fraction of the particle composition. Mixing ratios of common aerosol growth precursors, such as isoprene and sulfur dioxide, are not elevated during the episode, indicating that an unidentified aerosol growth precursor is present in this high-latitude marine environment.

Conditions for super-adiabatic droplet growth after entrainment mixing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Fan; Shaw, Raymond; Xue, Huiwen

Cloud droplet response to entrainment and mixing between a cloud and its environment is considered, accounting for subsequent droplet growth during adiabatic ascent following a mixing event. The vertical profile for liquid water mixing ratio after a mixing event is derived analytically, allowing the reduction to be predicted from the mixing fraction and from the temperature and humidity for both the cloud and environment. It is derived for the limit of homogeneous mixing. The expression leads to a critical height above the mixing level: at the critical height the cloud droplet radius is the same for both mixed and unmixedmore » parcels, and the critical height is independent of the updraft velocity and mixing fraction. Cloud droplets in a mixed parcel are larger than in an unmixed parcel above the critical height, which we refer to as the “super-adiabatic” growth region. Analytical results are confirmed with a bin microphysics cloud model. Using the model, we explore the effects of updraft velocity, aerosol source in the environmental air, and polydisperse cloud droplets. Results show that the mixed parcel is more likely to reach the super-adiabatic growth region when the environmental air is humid and clean. It is also confirmed that the analytical predictions are matched by the volume-mean cloud droplet radius for polydisperse size distributions. Lastly, these findings have implications for the origin of large cloud droplets that may contribute to onset of collision–coalescence in warm clouds.« less

Conditions for super-adiabatic droplet growth after entrainment mixing

DOE PAGES

Yang, Fan; Shaw, Raymond; Xue, Huiwen

2016-07-29

Cloud droplet response to entrainment and mixing between a cloud and its environment is considered, accounting for subsequent droplet growth during adiabatic ascent following a mixing event. The vertical profile for liquid water mixing ratio after a mixing event is derived analytically, allowing the reduction to be predicted from the mixing fraction and from the temperature and humidity for both the cloud and environment. It is derived for the limit of homogeneous mixing. The expression leads to a critical height above the mixing level: at the critical height the cloud droplet radius is the same for both mixed and unmixedmore » parcels, and the critical height is independent of the updraft velocity and mixing fraction. Cloud droplets in a mixed parcel are larger than in an unmixed parcel above the critical height, which we refer to as the “super-adiabatic” growth region. Analytical results are confirmed with a bin microphysics cloud model. Using the model, we explore the effects of updraft velocity, aerosol source in the environmental air, and polydisperse cloud droplets. Results show that the mixed parcel is more likely to reach the super-adiabatic growth region when the environmental air is humid and clean. It is also confirmed that the analytical predictions are matched by the volume-mean cloud droplet radius for polydisperse size distributions. Lastly, these findings have implications for the origin of large cloud droplets that may contribute to onset of collision–coalescence in warm clouds.« less

Mixing at double-Tee junctions with unequal pipe sizes in ...

EPA Pesticide Factsheets

Pipe flow mixing with various solute concentrations and flow rates at pipe junctions is investigated. The degree of mixing affects the spread of contaminants in a water distribution system. Many studies have been conducted on the mixing at the cross junctions. Yet a few have focused on double-Tee junctions of unequal pipe sizes. To investigate the solute mixing at double-Tee junctions with unequal pipe sizes, a series of experiments were conducted in a turbulent regime (Re=12500–50000) with different Reynolds number ratios and connecting pipe lengths. It is shown that dimensionless outlet concentrations depended on mixing mechanism at the impinging interface of junctions. Junction with a larger pipe size ratio is associated with more complete mixing. The inlet Reynolds number ratio affects mixing more strongly than the outlet Reynolds number ratio. Furthermore, the dimensionless connecting pipe length in a double-Tee played an important and complicated role in the flow mixing. Based on these results, two-dimensional isopleth maps were developed for the calculation of normalized north outlet concentration. This journal article is to communicate the research results on pipe juncture mixing, a widespread and important phenomena in distribution system water quality analysis. The research outcome improves EPANET modeling capability for safe water supplies. In addition, the research is one of the outputs from the EPA-MOST bilateral cooperative research Project #1

Modeling of mixing processes: Fluids, particulates, and powders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ottino, J.M.; Hansen, S.

Work under this grant involves two main areas: (1) Mixing of Viscous Liquids, this first area comprising aggregation, fragmentation and dispersion, and (2) Mixing of Powders. In order to produce a coherent self-contained picture, we report primarily on results obtained under (1), and within this area, mostly on computational studies of particle aggregation in regular and chaotic flows. Numerical simulations show that the average cluster size of compact clusters grows algebraically, while the average cluster size of fractal clusters grows exponentially; companion mathematical arguments are used to describe the initial growth of average cluster size and polydispersity. It is foundmore » that when the system is well mixed and the capture radius independent of mass, the polydispersity is constant for long-times and the cluster size distribution is self-similar. Furthermore, our simulations indicate that the fractal nature of the clusters is dependent upon the mixing.« less

Marathon: An Open Source Software Library for the Analysis of Markov-Chain Monte Carlo Algorithms

PubMed Central

Rechner, Steffen; Berger, Annabell

2016-01-01

We present the software library marathon, which is designed to support the analysis of sampling algorithms that are based on the Markov-Chain Monte Carlo principle. The main application of this library is the computation of properties of so-called state graphs, which represent the structure of Markov chains. We demonstrate applications and the usefulness of marathon by investigating the quality of several bounding methods on four well-known Markov chains for sampling perfect matchings and bipartite graphs. In a set of experiments, we compute the total mixing time and several of its bounds for a large number of input instances. We find that the upper bound gained by the famous canonical path method is often several magnitudes larger than the total mixing time and deteriorates with growing input size. In contrast, the spectral bound is found to be a precise approximation of the total mixing time. PMID:26824442

Cushing's disease due to mixed pituitary adenoma-gangliocytoma of the posterior pituitary gland presenting with Aspergillus sp. sinus infection.

PubMed

Bridenstine, Mark; Kerr, Janice M; Lillehei, Kevin O; Kleinschmidt-DeMasters, Bette K

2013-01-01

Gangliocytic lesions of the pituitary gland producing Cushing's disease are extremely rare entities that may exist with or without a pituitary adenoma. The latter have been designated mixed pituitary adenoma-gangliocytomas, the majority of which produce growth hormone, not adrenocorticotropin (ACTH), and are localized to the anterior gland. We now report an immunocompetent woman with hypercortisolism who presented with an intranasal aspergilloma eroding the bony sellar floor. The fungal ball was contiguous with, and extended into, a large neurohypophyseal-centered mass. Transsphenoidal resection revealed a gangliocytic lesion of the posterior gland with small clusters of intimately admixed ACTH-immunoreactive adenoma cells as the cause of her Cushing's disease. Rare transitional sizes and shapes of cells coupled with immunohistochemical findings supported interpretation as advanced neuronal metaplasia within an ACTH adenoma. This mixed ACTH adenoma-gangliocytoma is the first example to present clinically with an opportunistic infection.

Parametric Study of a Mixer/Ejector Nozzle with Mixing Enhancement Devices

NASA Technical Reports Server (NTRS)

DalBello, T.; Steffen, C. J., Jr.

2001-01-01

A numerical study employing a simplified model of the High Speed Civil Transport mixer/ejector nozzle has been conducted to investigate the effect of tabs (vortex generators) on the mixing process. More complete mixing of the primary and secondary flows within the confined ejector lowers peak exit velocity resulting in reduced jet noise. Tabs were modeled as vortex pairs and inserted into the computational model. The location, size, and number of tabs were varied and its effect on the mixing process is presented here both quantitatively and qualitatively. A baseline case (no tabs) along with six other cases involving two different vortex strengths at three different orientations have been computed and analyzed. The case with the highest vorticity (six vortices representing large tabs) gives the best mixing. It is shown that the influence of the vorticity acts primarily in the forward or middle portions of the duct, significantly alters the flow structure, and promotes some mixing in the lateral direction. Unmixed pockets were found at the top and bottom of the lobe, and more clever placement of tabs improved mixing in the vertical direction. The technique of replacing tabs with vortices shows promise as an efficient tool for quickly optimizing tab placement in lobed mixers.

Steady streaming: A key mixing mechanism in low-Reynolds-number acinar flows

PubMed Central

Kumar, Haribalan; Tawhai, Merryn H.; Hoffman, Eric A.; Lin, Ching-Long

2011-01-01

Study of mixing is important in understanding transport of submicron sized particles in the acinar region of the lung. In this article, we investigate transport in view of advective mixing utilizing Lagrangian particle tracking techniques: tracer advection, stretch rate and dispersion analysis. The phenomenon of steady streaming in an oscillatory flow is found to hold the key to the origin of kinematic mixing in the alveolus, the alveolar mouth and the alveolated duct. This mechanism provides the common route to folding of material lines and surfaces in any region of the acinar flow, and has no bearing on whether the geometry is expanding or if flow separates within the cavity or not. All analyses consistently indicate a significant decrease in mixing with decreasing Reynolds number (Re). For a given Re, dispersion is found to increase with degree of alveolation, indicating that geometry effects are important. These effects of Re and geometry can also be explained by the streaming mechanism. Based on flow conditions and resultant convective mixing measures, we conclude that significant convective mixing in the duct and within an alveolus could originate only in the first few generations of the acinar tree as a result of nonzero inertia, flow asymmetry, and large Keulegan–Carpenter (KC) number. PMID:21580803

Escape from the cryptic species trap: lichen evolution on both sides of a cyanobacterial acquisition event.

PubMed

Schneider, Kevin; Resl, Philipp; Spribille, Toby

2016-07-01

Large, architecturally complex lichen symbioses arose only a few times in evolution, increasing thallus size by orders of magnitude over those from which they evolved. The innovations that enabled symbiotic assemblages to acquire and maintain large sizes are unknown. We mapped morphometric data against an eight-locus fungal phylogeny across one of the best-sampled thallus size transition events, the origins of the Placopsis lichen symbiosis, and used a phylogenetic comparative framework to explore the role of nitrogen-fixing cyanobacteria in size differences. Thallus thickness increased by >150% and fruiting body core volume increased ninefold on average after acquisition of cyanobacteria. Volume of cyanobacteria-containing structures (cephalodia), once acquired, correlates with thallus thickness in both phylogenetic generalized least squares and phylogenetic generalized linear mixed-effects analyses. Our results suggest that the availability of nitrogen is an important factor in the formation of large thalli. Cyanobacterial symbiosis appears to have enabled lichens to overcome size constraints in oligotrophic environments such as acidic, rain-washed rock surfaces. In the case of the Placopsis fungal symbiont, this has led to an adaptive radiation of more than 60 recognized species from related crustose members of the genus Trapelia. Our data suggest that precyanobacterial symbiotic lineages were constrained to forming a narrow range of phenotypes, so-called cryptic species, leading systematists until now to recognize only six of the 13 species clusters we identified in Trapelia. © 2016 The Authors. Molecular Ecology Published by John Wiley & Sons Ltd.

Coupling of Waves, Turbulence and Thermodynamics Across the Marginal Ice Zone

DTIC Science & Technology

2013-09-30

ice . The albedo of sea ice is large compared to open water, and most of the incoming solar radiation...ocean and the ice pack where the seasonal retreat of the main ice pack takes place. It is a highly variable sea ice environment, usually comprised of...many individual floes of variable shape and size and made of mixed ice types, from young forming ice to fragmented multiyear ice . The presence of sea

Stability and compatibility assessment techniques for total parenteral nutrition admixtures: setting the bar according to pharmacopeial standards.

PubMed

Driscoll, David F

2005-05-01

The stability and compatibility of total parenteral nutrition mixtures compounded for patients requiring nutritional support is paramount to their safety on intravenous infusion. The most significant pharmaceutical issues associated with mixing total parenteral nutrition formulations affecting their safety involve the stability of lipid-injectable emulsions and the compatibility of calcium and phosphate salts. Methods of analysis for stability and compatibility have varied, and the assessments have mostly been largely qualitative. Although pharmacopeial standards have been primarily applicable to pharmaceutical manufacturers, recent efforts by the United States Pharmacopeia have been directed at standardizing pharmacy practices involved in the safe mixing of compounded sterile preparations. The adoption of chapter 797 entitled 'Pharmaceutical compounding - sterile preparations' on 1 January 2004 has had a dramatic impact on pharmacy practice in the United States. More recently, the United States Pharmacopeia has also proposed a new chapter 729 entitled 'Globule size distribution in lipid-injectable emulsions', setting specific limits on the sizes and concentrations of lipid droplets in the formulation, which may have implications for all-in-one mixtures. Finally, new efforts are under way to establish limits on the level of acceptable amounts of particulates intrinsically introduced by the manufacturer, and thus may have ramifications for particulates extrinsically introduced or initiated during compounding by the pharmacist. With careful monitoring and the development of appropriate pharmacopeial-based specifications that limit the size and concentration of large-diameter fat globules and eliminate the possibility of dibasic calcium phosphate precipitates, improved patient outcomes may be achieved.

Influence of Al Addition Upon the Microstructure and Mechanical Property of Dual-Phase 9Cr-ODS Steels

NASA Astrophysics Data System (ADS)

Zhou, Xiaosheng; Ma, Zongqing; Yu, Liming; Huang, Yuan; Li, Huijun; Liu, Yongchang

2018-06-01

With Al addition, dual-phase oxide dispersion strengthened (ODS) steels consisting of martensite and ferrite are fabricated by spark plasma sintering. It is found that Al addition has a negligible effect on martensite lath size, while the amount and size of ferrite grains are related to the Al content. M23C6 (M = Fe, Cr) carbides have been identified within the ferrite grains or along ferrite boundaries. With increasing Al concentration, more fine Y-Al-O oxide nanoparticles are formed. Upon annealing treatment, homogeneous and refined distribution of ferrite grains is obtained, which may involve the particle-stimulated nucleation of recrystallization caused by the large sized M23C6. As Al is increased from 0.05 to 0.1 wt%, the tensile strength of the annealed steel is decreased, as well as its ductility. For the annealed 9Cr-ODS steel containing 0.1 wt% Al, in tensile loading the large sized M23C6 along ferrite boundaries would facilitate the cracking along boundaries between the hard annealed ferrite and soft annealed martensite, producing the mixed fracture of dimple and intergranular fracture.

Electro-Optic and Photorefractive Response of Liquid Crystals with Inorganic Ferroelectric Nanoparticles

DTIC Science & Technology

2009-05-13

characterisation.   Methods, Assumptions, and Procedures   Ferroelectric particles  of  Sn2P2S6  and BaTiO3  (≅ 1 μm  size), mixed with  oleic  acid   in  a...with a  surfactant  for approximately 100 hours  in a micro‐ mill. A typical surfactant used for this purpose is oleic  acid . The finest, in size...explored  on  soft  polymers,  such  as  cinnamate   copolymers. While such technique may not be practical for large scale industrial devices  or  for  large

When smoke gets in our eyes: the multiple impacts of atmospheric black carbon on climate, air quality and health.

PubMed

Highwood, Eleanor J; Kinnersley, Robert P

2006-05-01

With both climate change and air quality on political and social agendas from local to global scale, the links between these hitherto separate fields are becoming more apparent. Black carbon, largely from combustion processes, scatters and absorbs incoming solar radiation, contributes to poor air quality and induces respiratory and cardiovascular problems. Uncertainties in the amount, location, size and shape of atmospheric black carbon cause large uncertainty in both climate change estimates and toxicology studies alike. Increased research has led to new effects and areas of uncertainty being uncovered. Here we draw together recent results and explore the increasing opportunities for synergistic research that will lead to improved confidence in the impact of black carbon on climate change, air quality and human health. Topics of mutual interest include better information on spatial distribution, size, mixing state and measuring and monitoring.

Mixing state of regionally transported soot particles and the coating effect on their size and shape at a mountain site in Japan

NASA Astrophysics Data System (ADS)

Adachi, Kouji; Zaizen, Yuji; Kajino, Mizuo; Igarashi, Yasuhito

2014-05-01

Soot particles influence the global climate through interactions with sunlight. A coating on soot particles increases their light absorption by increasing their absorption cross section and cloud condensation nuclei activity when mixed with other hygroscopic aerosol components. Therefore, it is important to understand how soot internally mixes with other materials to accurately simulate its effects in climate models. In this study, we used a transmission electron microscope (TEM) with an auto particle analysis system, which enables more particles to be analyzed than a conventional TEM. Using the TEM, soot particle size and shape (shape factor) were determined with and without coating from samples collected at a remote mountain site in Japan. The results indicate that ~10% of aerosol particles between 60 and 350 nm in aerodynamic diameters contain or consist of soot particles and ~75% of soot particles were internally mixed with nonvolatile ammonium sulfate or other materials. In contrast to an assumption that coatings change soot shape, both internally and externally mixed soot particles had similar shape and size distributions. Larger aerosol particles had higher soot mixing ratios, i.e., more than 40% of aerosol particles with diameters >1 µm had soot inclusions, whereas <20% of aerosol particles with diameters <1 µm included soot. Our results suggest that climate models may use the same size distributions and shapes for both internally and externally mixed soot; however, changing the soot mixing ratios in the different aerosol size bins is necessary.

Evaluation of the degree of mixing of combinations of dry syrup, powder, and fine granule products in consideration of particle size distribution using near infrared spectrometry.

PubMed

Yamamoto, Yoshihisa; Suzuki, Toyofumi; Matsumoto, Mika; Ohtani, Michiteru; Hayano, Shuichi; Fukami, Toshiro; Tomono, Kazuo

2012-01-01

We used near infrared (NIR) spectroscopy to evaluate the degree of mixing of blended dry syrup (DS) products whose particle sizes are not specified in the Revised 16th Edition of the Japanese Pharmacopoeia, and also evaluated the degree of mixing when powder products or fine granule products were added to DS products. The data obtained were used to investigate the relationship between the particle size distributions of the products studied and the degree of mixing. We found that the particle size distribution characteristics of the 15 DS products studied can be broadly classified into 5 types. Combinations of frequently prescribed products were selected to represent 4 of the 5 particle size distribution types and were blended with a mortar and pestle. The coefficient of variation (CV) decreased as the percent mass of Asverin® Dry Syrup 2% (Asverin-DS) increased in blends of Periactin® Powder 1% (Periactin) and Asverin-DS, indicating an improved degree of mixing (uniformity). In contrast, in blends of Periactin and Mucodyne® DS 33.3%, mixing a combination at a 1:1 mass ratio 40 times resulted in a CV of 20%. Other mixing frequencies and mass ratios resulted in a CV by 50% to 70%, indicating a very poor degree of mixing (poor uniformity). These results suggest that when combining different DSs, or a DS with a powder or fine granule product, the blending obtained with a mortar and pestle improves as the particle size distributions of the components approach each other and as the ranges of the distributions narrow.

Continuous manufacturing of extended release tablets via powder mixing and direct compression.

PubMed

Ervasti, Tuomas; Simonaho, Simo-Pekka; Ketolainen, Jarkko; Forsberg, Peter; Fransson, Magnus; Wikström, Håkan; Folestad, Staffan; Lakio, Satu; Tajarobi, Pirjo; Abrahmsén-Alami, Susanna

2015-11-10

The aim of the current work was to explore continuous dry powder mixing and direct compression for manufacturing of extended release (ER) matrix tablets. The study was span out with a challenging formulation design comprising ibuprofen compositions with varying particle size and a relatively low amount of the matrix former hydroxypropyl methylcellulose (HPMC). Standard grade HPMC (CR) was compared to a recently developed direct compressible grade (DC2). The work demonstrate that ER tablets with desired quality attributes could be manufactured via integrated continuous mixing and direct compression. The most robust tablet quality (weight, assay, tensile strength) was obtained using high mixer speed and large particle size ibuprofen and HPMC DC2 due to good powder flow. At low mixer speed it was more difficult to achieve high quality low dose tablets. Notably, with HPMC DC2 the processing conditions had a significant effect on drug release. Longer processing time and/or faster mixer speed was needed to achieve robust release with compositions containing DC2 compared with those containing CR. This work confirms the importance of balancing process parameters and material properties to find consistent product quality. Also, adaptive control is proven a pivotal means for control of continuous manufacturing systems. Copyright © 2015 Elsevier B.V. All rights reserved.

Toward Better Modeling of Supercritical Turbulent Mixing

NASA Technical Reports Server (NTRS)

Selle, Laurent; Okongo'o, Nora; Bellan, Josette; Harstad, Kenneth

2008-01-01

study was done as part of an effort to develop computational models representing turbulent mixing under thermodynamic supercritical (here, high pressure) conditions. The question was whether the large-eddy simulation (LES) approach, developed previously for atmospheric-pressure compressible-perfect-gas and incompressible flows, can be extended to real-gas non-ideal (including supercritical) fluid mixtures. [In LES, the governing equations are approximated such that the flow field is spatially filtered and subgrid-scale (SGS) phenomena are represented by models.] The study included analyses of results from direct numerical simulation (DNS) of several such mixing layers based on the Navier-Stokes, total-energy, and conservation- of-chemical-species governing equations. Comparison of LES and DNS results revealed the need to augment the atmospheric- pressure LES equations with additional SGS momentum and energy terms. These new terms are the direct result of high-density-gradient-magnitude regions found in the DNS and observed experimentally under fully turbulent flow conditions. A model has been derived for the new term in the momentum equation and was found to perform well at small filter size but to deteriorate with increasing filter size. Several alternative models were derived for the new SGS term in the energy equation that would need further investigations to determine if they are too computationally intensive in LES.

Eliciting mixed emotions: a meta-analysis comparing models, types, and measures.

PubMed

Berrios, Raul; Totterdell, Peter; Kellett, Stephen

2015-01-01

The idea that people can experience two oppositely valenced emotions has been controversial ever since early attempts to investigate the construct of mixed emotions. This meta-analysis examined the robustness with which mixed emotions have been elicited experimentally. A systematic literature search identified 63 experimental studies that instigated the experience of mixed emotions. Studies were distinguished according to the structure of the underlying affect model-dimensional or discrete-as well as according to the type of mixed emotions studied (e.g., happy-sad, fearful-happy, positive-negative). The meta-analysis using a random-effects model revealed a moderate to high effect size for the elicitation of mixed emotions (d IG+ = 0.77), which remained consistent regardless of the structure of the affect model, and across different types of mixed emotions. Several methodological and design moderators were tested. Studies using the minimum index (i.e., the minimum value between a pair of opposite valenced affects) resulted in smaller effect sizes, whereas subjective measures of mixed emotions increased the effect sizes. The presence of more women in the samples was also associated with larger effect sizes. The current study indicates that mixed emotions are a robust, measurable and non-artifactual experience. The results are discussed in terms of the implications for an affect system that has greater versatility and flexibility than previously thought.

Eliciting mixed emotions: a meta-analysis comparing models, types, and measures

PubMed Central

Berrios, Raul; Totterdell, Peter; Kellett, Stephen

2015-01-01

The idea that people can experience two oppositely valenced emotions has been controversial ever since early attempts to investigate the construct of mixed emotions. This meta-analysis examined the robustness with which mixed emotions have been elicited experimentally. A systematic literature search identified 63 experimental studies that instigated the experience of mixed emotions. Studies were distinguished according to the structure of the underlying affect model—dimensional or discrete—as well as according to the type of mixed emotions studied (e.g., happy-sad, fearful-happy, positive-negative). The meta-analysis using a random-effects model revealed a moderate to high effect size for the elicitation of mixed emotions (dIG+ = 0.77), which remained consistent regardless of the structure of the affect model, and across different types of mixed emotions. Several methodological and design moderators were tested. Studies using the minimum index (i.e., the minimum value between a pair of opposite valenced affects) resulted in smaller effect sizes, whereas subjective measures of mixed emotions increased the effect sizes. The presence of more women in the samples was also associated with larger effect sizes. The current study indicates that mixed emotions are a robust, measurable and non-artifactual experience. The results are discussed in terms of the implications for an affect system that has greater versatility and flexibility than previously thought. PMID:25926805

Perturbations of the optical properties of mineral dust particles by mixing with black carbon: a numerical simulation study

DOE PAGES

Scarnato, B. V.; China, S.; Nielsen, K.; ...

2015-06-25

Field observations show that individual aerosol particles are a complex mixture of a wide variety of species, reflecting different sources and physico-chemical transformations. The impacts of individual aerosol morphology and mixing characteristics on the Earth system are not yet fully understood. Here we present a sensitivity study on climate-relevant aerosols optical properties to various approximations. Based on aerosol samples collected in various geographical locations, we have observationally constrained size, morphology and mixing, and accordingly simulated, using the discrete dipole approximation model (DDSCAT), optical properties of three aerosols types: (1) bare black carbon (BC) aggregates, (2) bare mineral dust, and (3)more » an internal mixture of a BC aggregate laying on top of a mineral dust particle, also referred to as polluted dust. DDSCAT predicts optical properties and their spectral dependence consistently with observations for all the studied cases. Predicted values of mass absorption, scattering and extinction coefficients (MAC, MSC, MEC) for bare BC show a weak dependence on the BC aggregate size, while the asymmetry parameter ( g) shows the opposite behavior. The simulated optical properties of bare mineral dust present a large variability depending on the modeled dust shape, confirming the limited range of applicability of spheroids over different types and size of mineral dust aerosols, in agreement with previous modeling studies. The polluted dust cases show a strong decrease in MAC values with the increase in dust particle size (for the same BC size) and an increase of the single scattering albedo (SSA). Furthermore, particles with a radius between 180 and 300 nm are characterized by a decrease in SSA values compared to bare dust, in agreement with field observations.This paper demonstrates that observationally constrained DDSCAT simulations allow one to better understand the variability of the measured aerosol optical properties in ambient air and to define benchmark biases due to different approximations in aerosol parametrization.« less

Whole-Genome Resequencing of Experimental Populations Reveals Polygenic Basis of Egg-Size Variation in Drosophila melanogaster

PubMed Central

Jha, Aashish R.; Miles, Cecelia M.; Lippert, Nodia R.; Brown, Christopher D.; White, Kevin P.; Kreitman, Martin

2015-01-01

Complete genome resequencing of populations holds great promise in deconstructing complex polygenic traits to elucidate molecular and developmental mechanisms of adaptation. Egg size is a classic adaptive trait in insects, birds, and other taxa, but its highly polygenic architecture has prevented high-resolution genetic analysis. We used replicated experimental evolution in Drosophila melanogaster and whole-genome sequencing to identify consistent signatures of polygenic egg-size adaptation. A generalized linear-mixed model revealed reproducible allele frequency differences between replicated experimental populations selected for large and small egg volumes at approximately 4,000 single nucleotide polymorphisms (SNPs). Several hundred distinct genomic regions contain clusters of these SNPs and have lower heterozygosity than the genomic background, consistent with selection acting on polymorphisms in these regions. These SNPs are also enriched among genes expressed in Drosophila ovaries and many of these genes have well-defined functions in Drosophila oogenesis. Additional genes regulating egg development, growth, and cell size show evidence of directional selection as genes regulating these biological processes are enriched for highly differentiated SNPs. Genetic crosses performed with a subset of candidate genes demonstrated that these genes influence egg size, at least in the large genetic background. These findings confirm the highly polygenic architecture of this adaptive trait, and suggest the involvement of many novel candidate genes in regulating egg size. PMID:26044351

Developmental Environment Effects on Sexual Selection in Male and Female Drosophila melanogaster

PubMed Central

Morimoto, Juliano; Pizzari, Tommaso; Wigby, Stuart

2016-01-01

The developmental environment can potentially alter the adult social environment and influence traits targeted by sexual selection such as body size. In this study, we manipulated larval density in male and female Drosophila melanogaster, which results in distinct adult size phenotypes–high (low) densities for small (large) adults–and measured sexual selection in experimental groups consisting of adult males and females from high, low, or a mixture of low and high larval densities. Overall, large adult females (those reared at low larval density) had more matings, more mates and produced more offspring than small females (those reared at high larval density). The number of offspring produced by females was positively associated with their number of mates (i.e. there was a positive female Bateman gradient) in social groups where female size was experimentally varied, likely due to the covariance between female productivity and mating rate. For males, we found evidence that the larval environment affected the relative importance of sexual selection via mate number (Bateman gradients), mate productivity, paternity share, and their covariances. Mate number and mate productivity were significantly reduced for small males in social environments where males were of mixed sizes, versus social environments where all males were small, suggesting that social heterogeneity altered selection on this subset of males. Males are commonly assumed to benefit from mating with large females, but in contrast to expectations we found that in groups where both the male and female size varied, males did not gain more offspring per mating with large females. Collectively, our results indicate sex-specific effects of the developmental environment on the operation of sexual selection, via both the phenotype of individuals, and the phenotype of their competitors and mates. PMID:27167120

21 CFR 226.102 - Master-formula and batch-production records.

Code of Federal Regulations, 2010 CFR

2010-04-01

...(s) produced on a batch or continuous operation basis, including mixing steps and mixing times that have been determined to yield an adequately mixed Type A medicated article(s); and in the case of Type... batch size, or of appropriate size in the case of continuous systems to be produced from the master...

Coordination of size-control, reproduction and generational memory in freshwater planarians

NASA Astrophysics Data System (ADS)

Yang, Xingbo; Kaj, Kelson J.; Schwab, David J.; Collins, Eva-Maria S.

2017-06-01

Uncovering the mechanisms that control size, growth, and division rates of organisms reproducing through binary division means understanding basic principles of their life cycle. Recent work has focused on how division rates are regulated in bacteria and yeast, but this question has not yet been addressed in more complex, multicellular organisms. We have, over the course of several years, assembled a unique large-scale data set on the growth and asexual reproduction of two freshwater planarian species, Dugesia japonica and Girardia tigrina, which reproduce by transverse fission and succeeding regeneration of head and tail pieces into new planarians. We show that generation-dependent memory effects in planarian reproduction need to be taken into account to accurately capture the experimental data. To achieve this, we developed a new additive model that mixes multiple size control strategies based on planarian size, growth, and time between divisions. Our model quantifies the proportions of each strategy in the mixed dynamics, revealing the ability of the two planarian species to utilize different strategies in a coordinated manner for size control. Additionally, we found that head and tail offspring of both species employ different mechanisms to monitor and trigger their reproduction cycles. Thus, we find a diversity of strategies not only between species but between heads and tails within species. Our additive model provides two advantages over existing 2D models that fit a multivariable splitting rate function to the data for size control: firstly, it can be fit to relatively small data sets and can thus be applied to systems where available data is limited. Secondly, it enables new biological insights because it explicitly shows the contributions of different size control strategies for each offspring type.

Coordination of size-control, reproduction and generational memory in freshwater planarians.

PubMed

Yang, Xingbo; Kaj, Kelson J; Schwab, David J; Collins, Eva-Maria S

2017-05-23

Uncovering the mechanisms that control size, growth, and division rates of organisms reproducing through binary division means understanding basic principles of their life cycle. Recent work has focused on how division rates are regulated in bacteria and yeast, but this question has not yet been addressed in more complex, multicellular organisms. We have, over the course of several years, assembled a unique large-scale data set on the growth and asexual reproduction of two freshwater planarian species, Dugesia japonica and Girardia tigrina, which reproduce by transverse fission and succeeding regeneration of head and tail pieces into new planarians. We show that generation-dependent memory effects in planarian reproduction need to be taken into account to accurately capture the experimental data. To achieve this, we developed a new additive model that mixes multiple size control strategies based on planarian size, growth, and time between divisions. Our model quantifies the proportions of each strategy in the mixed dynamics, revealing the ability of the two planarian species to utilize different strategies in a coordinated manner for size control. Additionally, we found that head and tail offspring of both species employ different mechanisms to monitor and trigger their reproduction cycles. Thus, we find a diversity of strategies not only between species but between heads and tails within species. Our additive model provides two advantages over existing 2D models that fit a multivariable splitting rate function to the data for size control: firstly, it can be fit to relatively small data sets and can thus be applied to systems where available data is limited. Secondly, it enables new biological insights because it explicitly shows the contributions of different size control strategies for each offspring type.

The influence of the starvation-predation trade-off on the relationship between ambient temperature and body size among endotherms.

PubMed

McNamara, John M; Higginson, Andrew D; Verhulst, Simon

2016-04-01

The tendency for animals at higher latitudes to be larger (Bergmann's rule) is generally explained by recourse to latitudinal effects on ambient temperature and the food supply, but these receive only mixed support and do not explain observations of the inverse to Bergmann's rule. Our aim was to better understand how ecological variables might influence body size and thereby explain this mixed support. World-wide. Previous explanations do not allow for the selective pressure exerted by the trade-off between predation and starvation, which we incorporate in a model of optimal body size and energy storage of a generalized homeotherm. In contrast to existing arguments, we concentrate on survival over winter when the food supply is poor and can be interrupted for short periods. We use our model to assess the logical validity of the heat conservation hypothesis and show that it must allow for the roles of both food availability and predation risk. We find that whether the effect of temperature on body size is positive or negative depends on temperature range, predator density, and the likelihood of long interruptions to foraging. Furthermore, changing day length explains differing effects of altitude and latitude on body size, leading to opposite predictions for nocturnal and diurnal endotherms. Food availability and ambient temperature can have counteracting selective pressures on body mass, and can lead to a non-monotonic relationship between latitude and size, as observed in several studies. Our work provides a theoretical framework for understanding the relationships between the costs and benefits of large body size and eco-geographical patterns among endotherms world-wide.

Aerosol Classification from High Spectral Resolution Lidar Measurements

NASA Astrophysics Data System (ADS)

Burton, S. P.; Hair, J. W.; Ferrare, R. A.; Hostetler, C. A.; Kahnert, M.; Vaughan, M. A.; Cook, A. L.; Harper, D. B.; Berkoff, T.; Seaman, S. T.; Collins, J. E., Jr.; Fenn, M. A.; Rogers, R. R.

2015-12-01

The NASA Langley airborne High Spectral Resolution Lidars, HSRL-1 and HSRL-2, have acquired large datasets of vertically resolved aerosol extinction, backscatter, and depolarization during >30 airborne field missions since 2006. The lidar measurements of aerosol intensive parameters like lidar ratio and color ratio embed information about intrinsic aerosol properties, and are combined to qualitatively classify HSRL aerosol measurements into aerosol types. Knowledge of aerosol type is important for assessing aerosol radiative forcing, and can provide useful information for source attribution studies. However, atmospheric aerosol is frequently not a single pure type, but instead is a mixture, which affects the optical and radiative properties of the aerosol. We show that aerosol intensive parameters measured by lidar can be understood using mixing rules for cases of external mixing. Beyond coarse classification and mixing between classes, variations in the lidar aerosol intensive parameters provide additional insight into aerosol processes and composition. This is illustrated by depolarization measurements at three wavelengths, 355 nm, 532 nm, and 1064 nm, made by HSRL-2. Particle depolarization ratio is an indicator of non-spherical particles. Three cases each have a significantly different spectral dependence of the depolarization ratio, related to the size of the depolarizing particles. For two dust cases, large non-spherical particles account for the depolarization of the lidar light. The spectral dependence reflects the size distribution of these particles and reveals differences in the transport histories of the two plumes. For a smoke case, the depolarization is inferred to be due to the presence of small coated soot aggregates. Interestingly, the depolarization at 355 nm is similar for this smoke case compared to the dust cases, having potential implications for the upcoming EarthCARE satellite, which will measure particle depolarization ratio only at 355 nm.

Identification of different shapes, colors and sizes of standard oral dosage forms in diabetes type 2 patients-A pilot study.

PubMed

Stegemann, Sven; Riedl, Regina; Sourij, Harald

2017-01-30

The clear identification of drug products by the patients is essential for a safe and effective medication management. In order to understand the impact of shape, size and color on medication identification a study was performed in subjects with type 2 diabetes mellitus (T2D). Ten model drugs differentiated by shape, size and color were evaluated using a mixed method of medication schedule preparation by the participants followed by a semi-structured interview. Detection times were fastest for the large round tablet shape and the bi-chromatic forms. Larger size was easier to identify than the smaller sizes except for the bi-chromatic forms. The shape was the major source of errors, followed by the size and the color dimension. The results from this study suggests that color as a single dimension are perceived more effectively by subjects with T2D compared to shape and size, which requires a more demanding processing of three dimension and is dependent on the perspective. Copyright © 2016 Elsevier B.V. All rights reserved.

Hawks, doves, and mixed-symmetry games.

PubMed

Crowley, P H

2000-06-21

The hawk-dove game has proved to be an important tool for understanding the role of aggression in social interactions. Here, the game is presented in a more general form (GHD) to facilitate analyses of interactions between individuals that may differ in "size", where size is interpreted as a surrogate for resource holding power. Three different situations are considered, based on the availability and use of information that interacting individuals have about their sizes: the classical symmetric case, in which no information about sizes is used, the asymmetric case, in which the individuals know their relative sizes and thus their chances of prevailing in combat, and a mixed-symmetry case, in which each individual only knows its own size (or only knows its opponent's size). I describe and use some recently developed methods for multitype games-evolutionary games involving two or more categories of players. With these methods and others, the evolutionarily stable strategies (ESSs) that emerge for the three different cases are identified and compared. A proof of the form and uniqueness of the ESS for the mixed-symmetry case is presented. In this situation, one size category at most can play a mixed strategy; larger individuals are aggressive and smaller individuals are not. As the number of size categories approaches infinity and the size distribution becomes continuous, there is a threshold size, above which all individuals are aggressive, and below which they are not. Copyright 2000 Academic Press.

Concurrent changes in aggregation and swelling of coal particles in solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nishioka, M.

1995-12-31

A new method of coal swelling has been developed tinder the condition of low coal concentrations with continuous mixing of coal and solvent. The change in particle size distributions by a laser scattering procedure was used for the evaluation of coal swelling. Particle size distributions in good and poor solvents were nearly equal, but reversibly changed in good solvents from time to time. The effects of solubles and coal concentrations on the distributions were small. It was concluded that aggregate d coal particles disaggregate in good solvents, and that an increase in the particle size distribution due to swelling inmore » good solvents are compensated by a decrease in the particle size due to disaggregation. Therefore, the behavior of coal particles in solvents is controlled by aggregation in addition to coal swelling. This implies that an increase in the particle size due to coal swelling in actual processes is not so large as expected by the results obtained from the conventional coal swelling methods.« less

Use of botulinum toxin type A and type B for spasticity in upper and lower limbs.

PubMed

Bell, Kathleen R; Williams, Faren

2003-11-01

BT is likely effective in controlling spasticity in the smaller muscles of the arm and hand, although there has been only one large controlled trial. For lower limb spasticity, the outcomes are more mixed. No large randomized, controlled trials have been done, and the larger size of the muscles results in a decreased ability to treat widespread spasticity. For more focal treatment in the legs and feet, however, and when combined with other denervating agents or physical modalities, BT is probably effective. Careful analysis is warranted before performing any chemodenervation on a limb muscle or muscles.

Subcutaneous haemangiosarcoma in a cockatiel (Nymphicus hollandicus).

PubMed

Sledge, D G; Radi, Z A; Miller, D L; Lynn, B S

2006-08-01

An ulcerated, 1 x 0.5 cm, subcutaneous mass on the craniolateral aspect of the right tibiotarsus of a 4-year-old male cockatiel was removed. Histologically, the neoplasm was non-encapsulated, infiltrative and composed of irregular vascular channels lined by branching and variably sized spindle-shaped cells with large vesicular nuclei, prominent nucleoli and rare mitoses. Surrounding these vascular channels were fibroblasts and mixed inflammatory cells. Neoplastic cells had diffuse immunoreactivity to factor VIII supporting a diagnosis of haemangiosarcoma.

A hydrodynamic model for granular material flows including segregation effects

NASA Astrophysics Data System (ADS)

Gilberg, Dominik; Klar, Axel; Steiner, Konrad

2017-06-01

The simulation of granular flows including segregation effects in large industrial processes using particle methods is accurate, but very time-consuming. To overcome the long computation times a macroscopic model is a natural choice. Therefore, we couple a mixture theory based segregation model to a hydrodynamic model of Navier-Stokes-type, describing the flow behavior of the granular material. The granular flow model is a hybrid model derived from kinetic theory and a soil mechanical approach to cover the regime of fast dilute flow, as well as slow dense flow, where the density of the granular material is close to the maximum packing density. Originally, the segregation model has been formulated by Thornton and Gray for idealized avalanches. It is modified and adapted to be in the preferred form for the coupling. In the final coupled model the segregation process depends on the local state of the granular system. On the other hand, the granular system changes as differently mixed regions of the granular material differ i.e. in the packing density. For the modeling process the focus lies on dry granular material flows of two particle types differing only in size but can be easily extended to arbitrary granular mixtures of different particle size and density. To solve the coupled system a finite volume approach is used. To test the model the rotational mixing of small and large particles in a tumbler is simulated.

Effect of species mix on size/density and leaf-area relations in the southwest pinyon/juniper woodlands

Treesearch

Thomas M. Schuler; Frederick W. Smith

1988-01-01

The effects of species mix on stand structure and growth are evaluated for 117 pinyon (Pinus edulis Engelm.) and juniper (Juniperus monosperma (Engelm.) Sarg and J. osteosperma (Torr.) Little) woodlands of the southwestern United States. Maximum-size/density relations, leaf area and growth of pure and mixed-...

Physical Interpretation of Mixing Diagrams

NASA Astrophysics Data System (ADS)

Khain, Alexander; Pinsky, Mark; Magaritz-Ronen, L.

2018-01-01

Type of mixing at cloud edges is often determined by means of mixing diagrams showing the dependence of normalized cube of the mean volume radius on the dilution level. The mixing diagrams correspond to the final equilibrium state of mixing between two air volumes. While interpreting in situ measurements, scattering diagrams are plotted in which normalized droplet concentration is used instead of dilution level. Utilization of such scattering diagrams for interpretation of in situ observations faces significant difficulties and often leads to misinterpretation of the mixing process and to uncertain conclusions concerning the mixing type. In this study we analyze the scattering diagrams obtained by means of a Lagrangian-Eulerian model of a stratocumulus cloud. The model consists of 2,000 interacting Largangian parcels which mix with their neighbors during their motion in the atmospheric boundary layer. In the diagram, each parcel is denoted by a point. Changes of microphysical parameters of the parcel are represented by movements of the point in the scattering diagram. The method of plotting the scattering diagrams using the model is in many aspects similar to that used in in situ measurements. It is shown that a scattering diagram shows snapshots of a transient mixing process. The location of points in the scattering diagrams reflects largely the history and the origin of air parcels. Location of points on scattering diagram characterizes intensity of entrainment, and different parameters of droplet size distributions (DSDs) like concentration, mean volume (or effective) radius, and DSD width.

Vertically migrating swimmers generate aggregation-scale eddies in a stratified column.

PubMed

Houghton, Isabel A; Koseff, Jeffrey R; Monismith, Stephen G; Dabiri, John O

2018-04-01

Biologically generated turbulence has been proposed as an important contributor to nutrient transport and ocean mixing 1-3 . However, to produce non-negligible transport and mixing, such turbulence must produce eddies at scales comparable to the length scales of stratification in the ocean. It has previously been argued that biologically generated turbulence is limited to the scale of the individual animals involved 4 , which would make turbulence created by highly abundant centimetre-scale zooplankton such as krill irrelevant to ocean mixing. Their small size notwithstanding, zooplankton form dense aggregations tens of metres in vertical extent as they undergo diurnal vertical migration over hundreds of metres 3,5,6 . This behaviour potentially introduces additional length scales-such as the scale of the aggregation-that are of relevance to animal interactions with the surrounding water column. Here we show that the collective vertical migration of centimetre-scale swimmers-as represented by the brine shrimp Artemia salina-generates aggregation-scale eddies that mix a stable density stratification, resulting in an effective turbulent diffusivity up to three orders of magnitude larger than the molecular diffusivity of salt. These observed large-scale mixing eddies are the result of flow in the wakes of the individual organisms coalescing to form a large-scale downward jet during upward swimming, even in the presence of a strong density stratification relative to typical values observed in the ocean. The results illustrate the potential for marine zooplankton to considerably alter the physical and biogeochemical structure of the water column, with potentially widespread effects owing to their high abundance in climatically important regions of the ocean 7 .

Preparation of chitosan/tripolyphosphate nanoparticles with highly tunable size and low polydispersity.

PubMed

Sawtarie, Nader; Cai, Yuhang; Lapitsky, Yakov

2017-09-01

Nanoparticles prepared through the ionotropic gelation of chitosan with tripolyphosphate (TPP) have been extensively studied as vehicles for drug and gene delivery. Though a number of these works have focused on preparing particles with narrow size distributions, the monodisperse particles produced by these methods have been limited to narrow size ranges (where the average particle size was not varied by more than twofold). Here we show how, by tuning the NaCl concentration in the parent chitosan and TPP solutions, low-polydispersity particles with z-average diameters ranging between roughly 100 and 900nm can be prepared. Further, we explore how the size of these particles depends on the method by which the TPP is mixed into the chitosan solution, specifically comparing: (1) single-shot mixing; (2) dropwise addition; and (3) a dilution technique, where chitosan and TPP are codissolved at a high (gelation-inhibiting) ionic strength and then diluted to lower ionic strengths to trigger gelation. Though the particle size increases sigmoidally with the NaCl concentration for all three mixing methods, the dilution method delivers the most uniform/gradual size increase - i.e., it provides the most precise control. Also investigated are the effects of mixture composition and mixing procedure on the particle yield. These reveal the particle yield to increase with the chitosan/TPP concentration, decrease with the NaCl concentration, and vary only weakly with the mixing protocol; thus, at elevated NaCl concentrations, it may be beneficial to increase chitosan and TPP concentrations to ensure high particle yields. Finally, possible pitfalls of the salt-assisted size control strategy (and their solutions) are discussed. Taken together, these findings provide a simple and reliable method for extensively tuning chitosan/TPP particle size while maintaining narrow size distributions. Copyright © 2017 Elsevier B.V. All rights reserved.

[Effects of forest gap size and uprooted microsite on the microclimate in Pinus koraiensis-dominated broad-leaved mixed forest].

PubMed

Duan, Wen-biao; Du, Shan; Chen, Li-xin; Wang, Li-xia; Wei, Quan-shuai; Zhao, Jian-hui

2013-08-01

Three representative forest gaps with pit-mound microsites formed by uprooted trees were selected within the 2.55 hm2 plot in a Pinus koraiensis-dominated broad-leaved mixed forest in Xiao Xing'an Mountains of Northeast China. The cleared land and closed stand were set up as the controls, and the PAR, air temperature and relative humidity in the centers of different size gaps and in mound top as well as the total radiation and precipitation in the gap centers were measured between July and September, 2011 by using multichannel automatic meteorological stations. The differences of the microclimate between the gap centers and mound top in different months were compared, and the monthly and diurnal variations of the microclimatic factors in the gap centers and in the mound top under typical weather conditions were analyzed. The results showed that the mean monthly PAR and air temperature in the three gaps of different sizes were in the order of large gap > medium gap > small gap, and the mean monthly relative humidity was in the order of small gap > medium gap > large gap. For the same size gap, the mean monthly PAR and air temperature were higher in the mound top than in the gap center, whereas the mean monthly relative humidity was higher in the gap center than in the mound top. Both the mean monthly total radiation and the mean monthly air temperature in the forest gaps and in the controls were in the order of July > August > September and of cleared land > large gap > medium gap > small gap > closed stand, while the mean monthly relative humidity was in the order of closed stand > small gap > medium gap > large gap > cleared land. The differences in the mean monthly relative humidity between closed stand and various gaps and between closed stand and cleared land reached significant level. The monthly precipitation from July to September decreased in the order of cleared land > large gap > medium gap > small gap > closed stand. Whether in sunny days or in overcast days, the mean daily PAR and air temperature were higher in mound top than in gap center, and the mean daily relative humidity was in opposite. Whether in mound top or in gap center, the mean daily PAR and air temperature were higher in sunny days than in overcast days, while the mean daily relative humidity was higher in overcast days than in sunny days.

Scale dependence of entrainment-mixing mechanisms in cumulus clouds

DOE PAGES

Lu, Chunsong; Liu, Yangang; Niu, Shengjie; ...

2014-12-17

This work empirically examines the dependence of entrainment-mixing mechanisms on the averaging scale in cumulus clouds using in situ aircraft observations during the Routine Atmospheric Radiation Measurement Aerial Facility Clouds with Low Optical Water Depths Optical Radiative Observations (RACORO) field campaign. A new measure of homogeneous mixing degree is defined that can encompass all types of mixing mechanisms. Analysis of the dependence of the homogenous mixing degree on the averaging scale shows that, on average, the homogenous mixing degree decreases with increasing averaging scales, suggesting that apparent mixing mechanisms gradually approach from homogeneous mixing to extreme inhomogeneous mixing with increasingmore » scales. The scale dependence can be well quantified by an exponential function, providing first attempt at developing a scale-dependent parameterization for the entrainment-mixing mechanism. The influences of three factors on the scale dependence are further examined: droplet-free filament properties (size and fraction), microphysical properties (mean volume radius and liquid water content of cloud droplet size distributions adjacent to droplet-free filaments), and relative humidity of entrained dry air. It is found that the decreasing rate of homogeneous mixing degree with increasing averaging scales becomes larger with larger droplet-free filament size and fraction, larger mean volume radius and liquid water content, or higher relative humidity. The results underscore the necessity and possibility of considering averaging scale in representation of entrainment-mixing processes in atmospheric models.« less

IMPROVED BIOMASS UTILIZATION THROUGH REMOTE FLOW SENSING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington University- St. Louis: Muthanna Al-Dahhan

The growth of the livestock industry provides a valuable source of affordable, sustainable, and renewable bioenergy, while also requiring the safe disposal of the large quantities of animal wastes (manure) generated at dairy, swine, and poultry farms. If these biomass resources are mishandled and underutilized, major environmental problems will be created, such as surface and ground water contamination, odors, dust, ammonia leaching, and methane emission. Anaerobic digestion of animal wastes, in which microorganisms break down organic materials in the absence of oxygen, is one of the most promising waste treatment technologies. This process produces biogas typically containing {approx}65% methane andmore » {approx}35% carbon dioxide. The production of biogas through anaerobic digestion from animal wastes, landfills, and municipal waste water treatment plants represents a large source of renewable and sustainable bio-fuel. Such bio-fuel can be combusted directly, used in internal combustion engines, converted into methanol, or partially oxidized to produce synthesis gas (a mixture of hydrogen and carbon monoxide) that can be converted to clean liquid fuels and chemicals via Fischer-Tropsch synthesis. Different design and mixing configurations of anaerobic digesters for treating cow manure have been utilized commercially and/or tested on a laboratory scale. These digesters include mechanically mixed, gas recirculation mixed, and slurry recirculation mixed designs, as well as covered lagoon digesters. Mixing is an important parameter for successful performance of anaerobic digesters. It enhances substrate contact with the microbial community; improves pH, temperature and substrate/microorganism uniformity; prevents stratification and scum accumulation; facilitates the removal of biogas from the digester; reduces or eliminates the formation of inactive zones (dead zones); prevents settling of biomass and inert solids; and aids in particle size reduction. Unfortunately, information and findings in the literature on the effect of mixing on anaerobic digestion are contradictory. One reason is the lack of measurement techniques for opaque systems such as digesters. Better understanding of the mixing and hydrodynamics of digesters will result in appropriate design, configuration selection, scale-up, and performance, which will ultimately enable avoiding digester failures. Accordingly, this project sought to advance the fundamental knowledge and understanding of the design, scale up, operation, and performance of cow manure anaerobic digesters with high solids loading. The project systematically studied parameters affecting cow manure anaerobic digestion performance, in different configurations and sizes by implementing computer automated radioactive particle tracking (CARPT), computed tomography (CT), and computational fluid dynamics (CFD), and by developing novel multiple-particle CARPT (MP-CARPT) and dual source CT (DSCT) techniques. The accomplishments of the project were achieved in a collaborative effort among Washington University, the Oak Ridge National Laboratory, and the Iowa Energy Center teams. The following investigations and achievements were accomplished: Systematic studies of anaerobic digesters performance and kinetics using various configurations, modes of mixing, and scales (laboratory, pilot plant, and commercial sizes) were conducted and are discussed in Chapter 2. It was found that mixing significantly affected the performance of the pilot plant scale digester ({approx}97 liter). The detailed mixing and hydrodynamics were investigated using computer automated radioactive particle tracking (CARPT) techniques, and are discussed in Chapter 3. A novel multiple particle tracking technique (MP-CARPT) technique that can track simultaneously up to 8 particles was developed, tested, validated, and implemented. Phase distribution was investigated using gamma ray computer tomography (CT) techniques, which are discussed in Chapter 4. A novel dual source CT (DSCT) technique was developed to measure the phase distribution of dynamic three phase system such as digesters with high solids loading and other types of gas-liquid-solid fluidization systems. Evaluation and validation of the computational fluid dynamics (CFD) models and closures were conducted to model and simulate the hydrodynamics and mixing intensity of the anaerobic digesters (Chapter 5). It is strongly recommended that additional studies be conducted, both on hydrodynamics and performance, in large scale digesters. The studies should use advanced non-invasive measurement techniques, including the developed novel measurement techniques, to further understand their design, scale-up, performance, and operation to avoid any digester failure. The final goal is a system ready to be used by farmers on site for bioenergy production and for animal/farm waste treatment.« less

Mixed squamous cell and glandular papilloma of the lung: a case study and literature review.

PubMed

Inamura, Kentaro; Kumasaka, Toshio; Furuta, Reiko; Shimada, Kei; Hiyama, Noriko; Furuhata, Yoshiaki; Tanaka, Isao; Takemura, Tamiko

2011-04-01

Mixed squamous cell and glandular papilloma (mixed papilloma) of the lung is an extremely rare neoplasm, with only 10 cases reported so far in the English literature. We present a case study of endobronchial mixed papilloma with immunohistochemical and etiological investigations. A 49-year-old male with a smoking history complained of hemoptysis, presented with a lung mass closely adjacent to large vessels in the computed tomography findings, and underwent lobectomy. The 3.0-cm sized polypoid tumor was histologically diagnosed as endobronchial mixed papilloma. Immunohistochemically, intracellular mucin was positive for MUC5AC, which is expressed in tracheobronchial goblet cells. CAM5.2 and CK19 were diffusely positive, indicating that the tumor originated from the columnar epithelium by squamous metaplasia. CEA and CA19-9 were focally positive. A human papillomavirus (HPV) investigation with in situ hybridization using a wide spectrum probe and a newly-developed PCR system did not detect any HPV infection. Including this case with a detailed HPV investigation, all of the reported cases of mixed papilloma were HPV-negative, and a literature review including newly-reported cases indicated a high frequency of smoking in such cases. Endobronchial mixed papillomas might have a smoking-related etiology. © 2011 The Authors. Pathology International © 2011 Japanese Society of Pathology and Blackwell Publishing Asia Pty Ltd.

[Factors influencing tree radial growth of three common species in broad-leaved Korean pine mixed forests in Changbai Mountains, China].

PubMed

Cai, Li Rong; Kuang, Xu; Fang, Shuai; Yuan, Zuo Qiang; Lin, Fei; Ye, Ji; Hao, Zhan Qing; Wang, Xu Gao

2017-05-18

To understand the factors influencing tree radial growth, we analyzed the seasonal dynamics of tree growth of 3 common species (Pinus koraiensis, Tilia amurensis, Quercus mongolica), compared interspecific growth rates and explored the effects of size, neighborhood competition, soil and topography based on five years dendrometer bands monitoring data of the 3 common species in a broad-leaved Korean pine (P. koraiensis) mixed forest plot in Changbai Mountain, Northeast China. The results showed that the growth dynamics of 3 species were consistent. Trees began to grow in late May, thrived in July, grew at declining rates from late August and stopped growing in late October. Annual relative growth rates were significantly different among the species. Q. mongolica tended to grow faster than the other two species, and the differences of growth rates among the 3 species were especially large for small and medium trees. Tree growth rates of P. koraiensis and Q. mongolica were strongly decreased by neighborhood competition, while tree growth rate of T. amurensis was significantly related to tree size, soil and topography.

In-line monitoring of a pharmaceutical blending process using FT-Raman spectroscopy.

PubMed

Vergote, G J; De Beer, T R M; Vervaet, C; Remon, J P; Baeyens, W R G; Diericx, N; Verpoort, F

2004-03-01

FT-Raman spectroscopy (in combination with a fibre optic probe) was evaluated as an in-line tool to monitor a blending process of diltiazem hydrochloride pellets and paraffinic wax beads. The mean square of differences (MSD) between two consecutive spectra was used to identify the time required to obtain a homogeneous mixture. A traditional end-sampling thief probe was used to collect samples, followed by HPLC analysis to verify the Raman data. Large variations were seen in the FT-Raman spectra logged during the initial minutes of the blending process using a binary mixture (ratio: 50/50, w/w) of diltiazem pellets and paraffinic wax beads (particle size: 800-1200 microm). The MSD-profiles showed that a homogeneous mixture was obtained after about 15 min blending. HPLC analysis confirmed these observations. The Raman data showed that the mixing kinetics depended on the particle size of the material and on the mixing speed. The results of this study proved that FT-Raman spectroscopy can be successfully implemented as an in-line monitoring tool for blending processes.

Combining Airborne and Lidar Measurements for Attribution of Aerosol Layers

NASA Astrophysics Data System (ADS)

Nikandrova, A.; Väänänen, R.; Tabakova, K.; Kerminen, V. M.; O'Connor, E.

2016-12-01

The aim of this work was to identify discrete aerosol layers and diagnose their origin, investigate the strength of mixing within the free-troposphere and with the boundary layer (BL), and understand the impact that mixing has on local and long-range transport of aerosol. For these purposes we combined airborne in-situ aerosol measurements with data obtained by a High Spectral Resolution Lidar (HSRL). The HSRL was deployed in Hyytiälä, Southern Finland, from January to September 2014 as a part of the US DoE ARM (Atmospheric Radiation Measurement) Mobile Facility during the BAECC (Biogenic Aerosols - Effects on Cloud and Climate) Campaign. Two airborne campaigns took place in April and August 2014 during the BAECC campaign. The vertical profile of backscatter coefficient from the HSRL was used to diagnose the location and depth of significant aerosol layers in the atmosphere. Frequently, in addition to the BL, one or two tropospheric layers were identified. In-situ measurements of the aerosol size distribution in these layers were obtained from a Scanning Mobility Particle Sizer (SMPS) and Optical Particle Sizer (OPS), that were installed on board the aircraft; these measurements were combined to cover sizes ranging from 10 nm to 10 µm. As expected, the highest number concentration of aerosol particles at all size ranges was found predominantly in the BL. Many upper layers had size distributions with a similar shape to that in the BL but with overall lower concentrations attributed to dilution of particles into a large volume of air. Hence, these layers were likely of very similar origin to the air in the BL and presumably were the result of lofted residual layers. Intervening layers however, could contain markedly different distribution shapes, which could be attributed to both different air mass origins, and different ambient relative humidity. Potential for mixing between two discreet elevated layers was often seen as a thin interface layer, which exhibited a combination of properties from both layers. Strong turbulent mixing ensured lower variability in the size distribution in the BL on short timescales, with more variability seen in the free troposphere. 96-hour back trajectories from multiple altitudes were used to diagnose the air mass origin of each discrete layer.

A size-composition resolved aerosol model for simulating the dynamics of externally mixed particles: SCRAM (v 1.0)

NASA Astrophysics Data System (ADS)

Zhu, S.; Sartelet, K. N.; Seigneur, C.

2015-06-01

The Size-Composition Resolved Aerosol Model (SCRAM) for simulating the dynamics of externally mixed atmospheric particles is presented. This new model classifies aerosols by both composition and size, based on a comprehensive combination of all chemical species and their mass-fraction sections. All three main processes involved in aerosol dynamics (coagulation, condensation/evaporation and nucleation) are included. The model is first validated by comparison with a reference solution and with results of simulations using internally mixed particles. The degree of mixing of particles is investigated in a box model simulation using data representative of air pollution in Greater Paris. The relative influence on the mixing state of the different aerosol processes (condensation/evaporation, coagulation) and of the algorithm used to model condensation/evaporation (bulk equilibrium, dynamic) is studied.

Benchmarking protein-protein interface predictions: why you should care about protein size.

PubMed

Martin, Juliette

2014-07-01

A number of predictive methods have been developed to predict protein-protein binding sites. Each new method is traditionally benchmarked using sets of protein structures of various sizes, and global statistics are used to assess the quality of the prediction. Little attention has been paid to the potential bias due to protein size on these statistics. Indeed, small proteins involve proportionally more residues at interfaces than large ones. If a predictive method is biased toward small proteins, this can lead to an over-estimation of its performance. Here, we investigate the bias due to the size effect when benchmarking protein-protein interface prediction on the widely used docking benchmark 4.0. First, we simulate random scores that favor small proteins over large ones. Instead of the 0.5 AUC (Area Under the Curve) value expected by chance, these biased scores result in an AUC equal to 0.6 using hypergeometric distributions, and up to 0.65 using constant scores. We then use real prediction results to illustrate how to detect the size bias by shuffling, and subsequently correct it using a simple conversion of the scores into normalized ranks. In addition, we investigate the scores produced by eight published methods and show that they are all affected by the size effect, which can change their relative ranking. The size effect also has an impact on linear combination scores by modifying the relative contributions of each method. In the future, systematic corrections should be applied when benchmarking predictive methods using data sets with mixed protein sizes. © 2014 Wiley Periodicals, Inc.

The Florida Harvester Ant, Pogonomyrmex badius, Relies on Germination to Consume Large Seeds

PubMed Central

Kwapich, Christina L.

2016-01-01

The Florida harvester ant, Pogonomyrmex badius, is one of many ant species and genera that stores large numbers of seeds in damp, underground chambers for later consumption. A comparison of the sizes of seeds recovered from storage chambers with those of seed husks discarded following consumption revealed that the used seeds are far smaller than stored seeds. This difference in use-rate was confirmed in field and laboratory colonies by offering marked seeds of various sizes and monitoring the appearance of size-specific chaff. Because foragers collect a range of seed sizes but only open small seeds, large seeds accumulate, forming 70% or more of the weight of seed stores. Major workers increase the rates at which small and medium seeds are opened, but do not increase the size range of opened seeds. Experiments limiting ant access to portions of natural seed chambers showed that seeds germinate during storage, but that the ants rapidly remove them. When offered alongside non germinating seeds, germinating seeds were preferentially fed to larvae. The rate of germination during the annual cycle was determined by both burial in artificial chambers at various depths and under four laboratory temperatures. The germination rate depends upon the species of seed, the soil/laboratory temperature and/or the elapsed time. The seasonal soil temperature cycle generated germination patterns that vary with the mix of locally-available seeds. Taken together, exploitation of germination greatly increases the resources available to the ants in space and time. While the largest seeds may have the nutritional value of 15 small seeds, the inability of workers to open large seeds at will precludes them from rapid use during catastrophic events. The harvester ant’s approach to seed harvesting is therefore two-pronged, with both immediate and delayed payoffs arising from the tendency to forage for a wide variety of seeds sizes. PMID:27893844

The Florida Harvester Ant, Pogonomyrmex badius, Relies on Germination to Consume Large Seeds.

PubMed

Tschinkel, Walter R; Kwapich, Christina L

2016-01-01

The Florida harvester ant, Pogonomyrmex badius, is one of many ant species and genera that stores large numbers of seeds in damp, underground chambers for later consumption. A comparison of the sizes of seeds recovered from storage chambers with those of seed husks discarded following consumption revealed that the used seeds are far smaller than stored seeds. This difference in use-rate was confirmed in field and laboratory colonies by offering marked seeds of various sizes and monitoring the appearance of size-specific chaff. Because foragers collect a range of seed sizes but only open small seeds, large seeds accumulate, forming 70% or more of the weight of seed stores. Major workers increase the rates at which small and medium seeds are opened, but do not increase the size range of opened seeds. Experiments limiting ant access to portions of natural seed chambers showed that seeds germinate during storage, but that the ants rapidly remove them. When offered alongside non germinating seeds, germinating seeds were preferentially fed to larvae. The rate of germination during the annual cycle was determined by both burial in artificial chambers at various depths and under four laboratory temperatures. The germination rate depends upon the species of seed, the soil/laboratory temperature and/or the elapsed time. The seasonal soil temperature cycle generated germination patterns that vary with the mix of locally-available seeds. Taken together, exploitation of germination greatly increases the resources available to the ants in space and time. While the largest seeds may have the nutritional value of 15 small seeds, the inability of workers to open large seeds at will precludes them from rapid use during catastrophic events. The harvester ant's approach to seed harvesting is therefore two-pronged, with both immediate and delayed payoffs arising from the tendency to forage for a wide variety of seeds sizes.

Primary particle diameter differentiation and bimodality identification by five analytical methods using gold nanoparticle size distributions synthesized by pulsed laser ablation in liquids

NASA Astrophysics Data System (ADS)

Letzel, Alexander; Gökce, Bilal; Menzel, Andreas; Plech, Anton; Barcikowski, Stephan

2018-03-01

For a known material, the size distribution of a nanoparticle colloid is a crucial parameter that defines its properties. However, measured size distributions are not easy to interpret as one has to consider weighting (e.g. by light absorption, scattering intensity, volume, surface, number) and the way size information was gained. The radius of a suspended nanoparticle can be given as e.g. sphere equivalent, hydrodynamic, Feret or radius of gyration. In this study, gold nanoparticles in water are synthesized by pulsed-laser ablation (LAL) and fragmentation (LFL) in liquids and characterized by various techniques (scanning transmission electron microscopy (STEM), small-angle X-ray scattering (SAXS), analytical disc centrifugation (ADC), dynamic light scattering (DLS) and UV-vis spectroscopy with Mie-Gans Theory) to study the comparability of different analytical techniques and determine the method that is preferable for a given task related to laser-generated nanoparticles. In particular, laser-generated colloids are known to be bimodal and/or polydisperse, but bimodality is sometimes not analytically resolved in literature. In addition, frequently reported small size shifts of the primary particle mode around 10 nm needs evaluation of its statistical significance related to the analytical method. Closely related to earlier studies on SAXS, different colloids in defined proportions are mixed and their size as a function of the nominal mixing ratio is analyzed. It is found that the derived particle size is independent of the nominal mixing ratio if the colloid size fractions do not overlap considerably. Conversely, the obtained size for colloids with overlapping size fractions strongly depends on the nominal mixing ratio since most methods cannot distinguish between such fractions. Overall, SAXS and ADC are very accurate methods for particle size analysis. Further, the ability of different methods to determine the nominal mixing ratio of sizes fractions is studied experimentally.

Impact of portion size and energy density on snack intake in preschool-aged children.

PubMed

Looney, Shannon M; Raynor, Hollie A

2011-03-01

The influence of dietary environmental factors on child weight status may be important in the battle against childhood obesity. Portion size and energy density are factors shown to impact entrée energy intake in children. However, the influence of these factors on child snack energy intake has not been studied. Thus, the aim of this study was to investigate the impact of portion size on intake of a lower energy-dense and higher energy-dense snack in preschool-aged children. A 2×2 crossover design (within-subject factors of portion size and energy density) was conducted on Wednesdays in a preschool setting on the University of Tennessee campus from October 2008 to November 2008. Seventeen children had complete data (age 3.8±0.6 years; 10 of 17 were female; 14 of 17 were white). Foods were applesauce (lower energy dense=0.43 kcal/g) and chocolate pudding (higher energy dense=1.19 kcal/g), and portion sizes were 150 g (small) and 300 g (large). Measures included anthropometrics, hunger, liking of foods, and caretakers' child-feeding practices using validated instruments. Mixed factorial analyses of covariance, with order controlled, analyzed gram and energy snack intake across conditions. There was no significant main effect of energy density on snack intake, but the main effect of portion size on snack intake (small portion size 84.2±30.8 kcal, large portion size 99.0±52.5 kcal; P<0.05) was significant. Results indicate increased energy intake when snacks are offered in larger portion size, regardless of energy density. Snack portion size may be an environmental strategy that can reduce excessive energy intake in children. Copyright © 2011 American Dietetic Association. Published by Elsevier Inc. All rights reserved.

Using different assumptions of aerosol mixing state and chemical composition to predict CCN concentrations based on field measurements in urban Beijing

NASA Astrophysics Data System (ADS)

Ren, Jingye; Zhang, Fang; Wang, Yuying; Collins, Don; Fan, Xinxin; Jin, Xiaoai; Xu, Weiqi; Sun, Yele; Cribb, Maureen; Li, Zhanqing

2018-05-01

Understanding the impacts of aerosol chemical composition and mixing state on cloud condensation nuclei (CCN) activity in polluted areas is crucial for accurately predicting CCN number concentrations (NCCN). In this study, we predict NCCN under five assumed schemes of aerosol chemical composition and mixing state based on field measurements in Beijing during the winter of 2016. Our results show that the best closure is achieved with the assumption of size dependent chemical composition for which sulfate, nitrate, secondary organic aerosols, and aged black carbon are internally mixed with each other but externally mixed with primary organic aerosol and fresh black carbon (external-internal size-resolved, abbreviated as EI-SR scheme). The resulting ratios of predicted-to-measured NCCN (RCCN_p/m) were 0.90 - 0.98 under both clean and polluted conditions. Assumption of an internal mixture and bulk chemical composition (INT-BK scheme) shows good closure with RCCN_p/m of 1.0 -1.16 under clean conditions, implying that it is adequate for CCN prediction in continental clean regions. On polluted days, assuming the aerosol is internally mixed and has a chemical composition that is size dependent (INT-SR scheme) achieves better closure than the INT-BK scheme due to the heterogeneity and variation in particle composition at different sizes. The improved closure achieved using the EI-SR and INT-SR assumptions highlight the importance of measuring size-resolved chemical composition for CCN predictions in polluted regions. NCCN is significantly underestimated (with RCCN_p/m of 0.66 - 0.75) when using the schemes of external mixtures with bulk (EXT-BK scheme) or size-resolved composition (EXT-SR scheme), implying that primary particles experience rapid aging and physical mixing processes in urban Beijing. However, our results show that the aerosol mixing state plays a minor role in CCN prediction when the κorg exceeds 0.1.

Trophic niches of sympatric tropical tuna in the Western Indian Ocean inferred by stable isotopes and neutral fatty acids

NASA Astrophysics Data System (ADS)

Sardenne, Fany; Bodin, Nathalie; Chassot, Emmanuel; Amiel, Aurélien; Fouché, Edwin; Degroote, Maxime; Hollanda, Stéphanie; Pethybridge, Heidi; Lebreton, Benoit; Guillou, Gaël; Ménard, Frédéric

2016-08-01

This study examined the trophic ecology of three sympatric tropical tuna species (bigeye BET, skipjack SKJ, and yellowfin YFT) sampled in the Western Indian Ocean throughout 2013. Specifically we explored inter-specific resource partitioning and ontogenetic variability using neutral fatty acids and stable isotope analysis of liver and muscle from small (⩽100 cm fork length, FL) and large (>100 cm FL) tuna collected in mixed schools at the surface by purse-seine. Both biochemical tracers were used to calculate trophic niche indices that collectively revealed high potential for resource overlap, especially among small tuna. Resource overlap appeared strongest between BET and YFT, with SKJ tissues having high carbon isotope (δ13C) values (-17 ± 0.3‰), lower nitrogen isotope (δ15N) values (11.4 ± 0.6‰), and higher relative proportion of poly-unsaturated fatty acids (PUFA) than the two other species, indicating a different diet. Size was found to be a strong predictor for most biochemical tracers in the three species with δ13C, δ15N and total lipid content in the liver. In the larger species (YFT and BET), proportions of mono-unsaturated fatty acids typically increased with size, while quantities of PUFA decreased. In addition to ontogenetic variability, trophic markers were shown to vary between sampling area and season: higher lipid reserves and δ15N values, and lower δ13C values occurred during monsoon periods around Seychelles than in the Mozambique Channel (parted from about 1500 km). Our multi-tracer approach reveals the magnitude of potential competitive interactions in mixed tropical tuna schools at both small and large sizes and demonstrates that ontogenetic niche differentiation acts as a major factor of coexistence in tropical tuna.

A Mixed-Methods Evaluation of the Choose Less, Weigh Less Portion Size Health Marketing Campaign in Los Angeles County.

PubMed

Gase, Lauren N; Barragan, Noel C; Robles, Brenda; Leighs, Michael; Kuo, Tony

2015-01-01

To assess the impact of the Choose Less, Weigh Less portion size health marketing campaign. A mixed-methods, cross-sectional evaluation. A quantitative Internet panel survey was administered through an online sampling vendor and qualitative interviews were conducted by street intercept. The panel survey included 796 participants, weighted to represent Los Angeles County. Street intercept interviews were conducted with 50 other participants. The Choose Less, Weigh Less campaign included print media on transit shelters, bus and rail cars, and billboards; radio and online advertising; and Web site content and social media outreach. The panel survey measured self-reported campaign exposure and outcomes, including knowledge of recommended daily calorie limits, attitudes toward portion sizes, and intent to reduce calories and portion size. Intercept interviews assessed campaign appeal, clarity, and utility. Weighted survey data were analyzed using logistic regression to assess the association between campaign exposure and outcomes. Interview data were analyzed for themes. The campaign reached 19.7% of the Los Angeles County population. Significant differences were seen for 2 of the 10 outcomes assessed. Participants who saw the campaign were more likely than those who did not to report fast-food portion sizes as being too large (adjusted odds ratio [Adj. OR]: 1.89; 95% confidence interval [CI]: 1.16, 3.07) and intention to choose a smaller portion (Adj. OR: 1.99; 95% CI: 1.20, 3.31). Qualitative data revealed three themes about appeal, clarity, and utility. Health marketing efforts targeting portion size can have relatively broad reach and limited but positive impacts on consumer attitudes and intent to select smaller portions.

Room Temperature Ion-Beam-Induced Recrystallization and Large Scale Nanopatterning.

PubMed

Satpati, Biswarup; Ghosh, Tanmay

2015-02-01

We have studied ion-induced effects in the near-surface region of two eutectic systems. Gold and Silver nanodots on Silicon (100) substrate were prepared by thermal evaporation under high vacuum condition at room temperature (RT) and irradiated with 1.5 MeV Au2+ ions at flux ~1.25 x 10(11) ions cm-2 s-1 also at RT. These samples were characterized using cross-sectional transmission electron microscopy (XTEM) and associated techniques. We have observed that gold act as catalysis in the recrystallization process of ion-beam-induced amorphous Si at room temperature and also large mass transport up to a distance of about 60 nm into the substrate. Mass transport is much beyond the size (~ 6-20 nm) of these Au nanodots. Ag nanoparticles with diameter 15-45 nm are half-way embedded into the Si substrate and does not stimulate in recrystallization. In case of Au nanoparticles upon ion irradiation, mixed phase formed only when the local composition and transient temperature during irradiation is sufficient to cause mixing in accordance with the Au-Si stable phase diagram. Spectroscopic imaging in the scanning TEM using spatially resolved electron energy loss spectroscopy provides one of the few ways to measure the real-space nanoscale mixing.

TiO2 Nanotubes: Recent Advances in Synthesis and Gas Sensing Properties

PubMed Central

Galstyan, Vardan; Comini, Elisabetta; Faglia, Guido; Sberveglieri, Giorgio

2013-01-01

Synthesis—particularly by electrochemical anodization-, growth mechanism and chemical sensing properties of pure, doped and mixed titania tubular arrays are reviewed. The first part deals on how anodization parameters affect the size, shape and morphology of titania nanotubes. In the second part fabrication of sensing devices based on titania nanotubes is presented, together with their most notable gas sensing performances. Doping largely improves conductivity and enhances gas sensing performances of TiO2 nanotubes. PMID:24184919

Archaeological Investigations in the Upper Tombigbee Valley, Mississippi: Phase I. Volume 3.

DTIC Science & Technology

1983-01-01

floodplain forest composed of mixed mesophytic species (Table 3.2). The Beech site exhibits a later successional stage as exemplified by the size of trees and...the old agricultural field and the floodplain forest, which is dominated locally by large hickory trees of at least four species . The terrace...expected as there was a living peach tree on the site at the time of the investigations. SURFACE COLLECTIONS (Figure 9.9 and 9.10 a-c) Surface

Combined discrete particle and continuum model predicting solid-state fermentation in a drum fermentor.

PubMed

Schutyser, M A I; Briels, W J; Boom, R M; Rinzema, A

2004-05-20

The development of mathematical models facilitates industrial (large-scale) application of solid-state fermentation (SSF). In this study, a two-phase model of a drum fermentor is developed that consists of a discrete particle model (solid phase) and a continuum model (gas phase). The continuum model describes the distribution of air in the bed injected via an aeration pipe. The discrete particle model describes the solid phase. In previous work, mixing during SSF was predicted with the discrete particle model, although mixing simulations were not carried out in the current work. Heat and mass transfer between the two phases and biomass growth were implemented in the two-phase model. Validation experiments were conducted in a 28-dm3 drum fermentor. In this fermentor, sufficient aeration was provided to control the temperatures near the optimum value for growth during the first 45-50 hours. Several simulations were also conducted for different fermentor scales. Forced aeration via a single pipe in the drum fermentors did not provide homogeneous cooling in the substrate bed. Due to large temperature gradients, biomass yield decreased severely with increasing size of the fermentor. Improvement of air distribution would be required to avoid the need for frequent mixing events, during which growth is hampered. From these results, it was concluded that the two-phase model developed is a powerful tool to investigate design and scale-up of aerated (mixed) SSF fermentors. Copyright 2004 Wiley Periodicals, Inc.

Representation of Arctic mixed-phase clouds and the Wegener-Bergeron-Findeisen process in climate models: Perspectives from a cloud-resolving study

NASA Astrophysics Data System (ADS)

Fan, Jiwen; Ghan, Steven; Ovchinnikov, Mikhail; Liu, Xiaohong; Rasch, Philip J.; Korolev, Alexei

2011-01-01

Two types of Arctic mixed-phase clouds observed during the ISDAC and M-PACE field campaigns are simulated using a 3-dimensional cloud-resolving model (CRM) with size-resolved cloud microphysics. The modeled cloud properties agree reasonably well with aircraft measurements and surface-based retrievals. Cloud properties such as the probability density function (PDF) of vertical velocity (w), cloud liquid and ice, regimes of cloud particle growth, including the Wegener-Bergeron-Findeisen (WBF) process, and the relationships among properties/processes in mixed-phase clouds are examined to gain insights for improving their representation in General Circulation Models (GCMs). The PDF of the simulated w is well represented by a Gaussian function, validating, at least for arctic clouds, the subgrid treatment used in GCMs. The PDFs of liquid and ice water contents can be approximated by Gamma functions, and a Gaussian function can describe the total water distribution, but a fixed variance assumption should be avoided in both cases. The CRM results support the assumption frequently used in GCMs that mixed phase clouds maintain water vapor near liquid saturation. Thus, ice continues to grow throughout the stratiform cloud but the WBF process occurs in about 50% of cloud volume where liquid and ice co-exist, predominantly in downdrafts. In updrafts, liquid and ice particles grow simultaneously. The relationship between the ice depositional growth rate and cloud ice strongly depends on the capacitance of ice particles. The simplified size-independent capacitance of ice particles used in GCMs could lead to large deviations in ice depositional growth.

Whole-Genome Resequencing of Experimental Populations Reveals Polygenic Basis of Egg-Size Variation in Drosophila melanogaster.

PubMed

Jha, Aashish R; Miles, Cecelia M; Lippert, Nodia R; Brown, Christopher D; White, Kevin P; Kreitman, Martin

2015-10-01

Complete genome resequencing of populations holds great promise in deconstructing complex polygenic traits to elucidate molecular and developmental mechanisms of adaptation. Egg size is a classic adaptive trait in insects, birds, and other taxa, but its highly polygenic architecture has prevented high-resolution genetic analysis. We used replicated experimental evolution in Drosophila melanogaster and whole-genome sequencing to identify consistent signatures of polygenic egg-size adaptation. A generalized linear-mixed model revealed reproducible allele frequency differences between replicated experimental populations selected for large and small egg volumes at approximately 4,000 single nucleotide polymorphisms (SNPs). Several hundred distinct genomic regions contain clusters of these SNPs and have lower heterozygosity than the genomic background, consistent with selection acting on polymorphisms in these regions. These SNPs are also enriched among genes expressed in Drosophila ovaries and many of these genes have well-defined functions in Drosophila oogenesis. Additional genes regulating egg development, growth, and cell size show evidence of directional selection as genes regulating these biological processes are enriched for highly differentiated SNPs. Genetic crosses performed with a subset of candidate genes demonstrated that these genes influence egg size, at least in the large genetic background. These findings confirm the highly polygenic architecture of this adaptive trait, and suggest the involvement of many novel candidate genes in regulating egg size. © The Author 2015. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

Porous media grain size distribution and hydrodynamic forces effects on transport and deposition of suspended particles.

PubMed

Ahfir, Nasre-Dine; Hammadi, Ahmed; Alem, Abdellah; Wang, HuaQing; Le Bras, Gilbert; Ouahbi, Tariq

2017-03-01

The effects of porous media grain size distribution on the transport and deposition of polydisperse suspended particles under different flow velocities were investigated. Selected Kaolinite particles (2-30μm) and Fluorescein (dissolved tracer) were injected in the porous media by step input injection technique. Three sands filled columns were used: Fine sand, Coarse sand, and a third sand (Mixture) obtained by mixing the two last sands in equal weight proportion. The porous media performance on the particle removal was evaluated by analysing particles breakthrough curves, hydro-dispersive parameters determined using the analytical solution of convection-dispersion equation with a first order deposition kinetics, particles deposition profiles, and particle-size distribution of the recovered and the deposited particles. The deposition kinetics and the longitudinal hydrodynamic dispersion coefficients are controlled by the porous media grain size distribution. Mixture sand is more dispersive than Fine and Coarse sands. More the uniformity coefficient of the porous medium is large, higher is the filtration efficiency. At low velocities, porous media capture all sizes of suspended particles injected with larger ones mainly captured at the entrance. A high flow velocity carries the particles deeper into the porous media, producing more gradual changes in the deposition profile. The median diameter of the deposited particles at different depth increases with flow velocity. The large grain size distribution leads to build narrow pores enhancing the deposition of the particles by straining. Copyright © 2016. Published by Elsevier B.V.

Effect of high-pressure homogenization on droplet size distribution and rheological properties of ice cream mixes.

PubMed

Innocente, N; Biasutti, M; Venir, E; Spaziani, M; Marchesini, G

2009-05-01

The effect of different homogenization pressures (15/3 MPa and 97/3 MPa) on fat globule size and distribution as well as on structure-property relationships of ice cream mixes was investigated. Dynamic light scattering, steady shear, and dynamic rheological analyses were performed on mixes with different fat contents (5 and 8%) and different aging times (4 and 20 h). The homogenization of ice cream mixes determined a change from bimodal to monomodal particle size distributions and a reduction in the mean particle diameter. Mean fat globule diameters were reduced at higher pressure, but the homogenization effect on size reduction was less marked with the highest fat content. The rheological behavior of mixes was influenced by both the dispersed and the continuous phases. Higher fat contents caused greater viscosity and dynamic moduli. The lower homogenization pressure (15/3 MPa) mainly affected the dispersed phase and resulted in a more pronounced viscosity reduction in the higher fat content mixes. High-pressure homogenization (97/3 MPa) greatly enhanced the viscoelastic properties and the apparent viscosity. Rheological results indicated that unhomogenized and 15/3 MPa homogenized mixes behaved as weak gels. The 97/3 MPa treatment led to stronger gels, perhaps as the overall result of a network rearrangement or interpenetrating network formation, and the fat globules were found to behave as interactive fillers. High-pressure homogenization determined the apparent viscosity of 5% fat to be comparable to that of 8% fat unhomogenized mix.

Oil Droplet Size Distribution and Optical Properties During Wave Tank Simulated Oil Spills

NASA Astrophysics Data System (ADS)

Conmy, R. N.; Venosa, A.; Courtenay, S.; King, T.; Robinson, B.; Ryan, S.

2013-12-01

Fate and transport of spilled petroleum oils in aquatic environments is highly dependent upon oil droplet behavior which is a function of chemical composition, dispersibility (natural and chemically-enhanced) and droplet size distribution (DSD) of the oil. DSD is influenced by mixing energy, temperature, salinity, pressure, presence of dissolved and particulate materials, flow rate of release, and application of dispersants. To better understand DSD and droplet behavior under varying physical conditions, flask-scale experiments are often insufficient. Rather, wave tank simulations allow for scaling to field conditions. Presented here are experiment results from the Bedford Institute of Oceanography wave tank facility, where chemically-dispersed (Corexit 9500; DOR = 1:20) Louisiana Sweet crude, IFO-120 and ANS crude oil were exposed to mixing energies to achieve dispersant effectiveness observed in the field. Oil plumes were simulated, both surface and subsea releases with varying water temperature and flow rate. Fluorometers (Chelsea Technologies Group AQUATracka, Turner Designs Cyclops, WET Labs Inc ECO) and particle size analyzers (Sequoia LISST) were used to track the dispersed plumes in the tank and characterize oil droplets. Sensors were validated with known oil volumes (down to 300 ppb) and measured Total Petroleum Hydrocarbons (TPH) and Benzene-Toluene-Ethylbenzene-Xylene (BTEX) values. This work has large implications for tracking surface and deep sea oil plumes with fluorescence and particle size analyzers, improved weathering and biodegradation estimates, and understanding the fate and transport of spill oil.

Significance of the model considering mixed grain-size for inverse analysis of turbidites

NASA Astrophysics Data System (ADS)

Nakao, K.; Naruse, H.; Tokuhashi, S., Sr.

2016-12-01

A method for inverse analysis of turbidity currents is proposed for application to field observations. Estimation of initial condition of the catastrophic events from field observations has been important for sedimentological researches. For instance, there are various inverse analyses to estimate hydraulic conditions from topography observations of pyroclastic flows (Rossano et al., 1996), real-time monitored debris-flow events (Fraccarollo and Papa, 2000), tsunami deposits (Jaffe and Gelfenbaum, 2007) and ancient turbidites (Falcini et al., 2009). These inverse analyses need forward models and the most turbidity current models employ uniform grain-size particles. The turbidity currents, however, are the best characterized by variation of grain-size distribution. Though there are numerical models of mixed grain-sized particles, the models have difficulty in feasibility of application to natural examples because of calculating costs (Lesshaft et al., 2011). Here we expand the turbidity current model based on the non-steady 1D shallow-water equation at low calculation costs for mixed grain-size particles and applied the model to the inverse analysis. In this study, we compared two forward models considering uniform and mixed grain-size particles respectively. We adopted inverse analysis based on the Simplex method that optimizes the initial conditions (thickness, depth-averaged velocity and depth-averaged volumetric concentration of a turbidity current) with multi-point start and employed the result of the forward model [h: 2.0 m, U: 5.0 m/s, C: 0.01%] as reference data. The result shows that inverse analysis using the mixed grain-size model found the known initial condition of reference data even if the condition where the optimization started is deviated from the true solution, whereas the inverse analysis using the uniform grain-size model requires the condition in which the starting parameters for optimization must be in quite narrow range near the solution. The uniform grain-size model often reaches to local optimum condition that is significantly different from true solution. In conclusion, we propose a method of optimization based on the model considering mixed grain-size particles, and show its application to examples of turbidites in the Kiyosumi Formation, Boso Peninsula, Japan.

Physicochemical perspectives (aggregation, structure and dynamics) of interaction between pluronic (L31) and surfactant (SDS).

PubMed

Prameela, G K S; Phani Kumar, B V N; Pan, A; Aswal, V K; Subramanian, J; Mandal, A B; Moulik, S P

2015-11-11

The influence of the water soluble non-ionic tri-block copolymer PEO-PPO-PEO [poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide)] i.e., E2P16E2 (L31) on the microstructure and self-aggregation dynamics of the anionic surfactant sodium dodecylsulfate (SDS) in aqueous solution was investigated using cloud point (CP), isothermal titration calorimetry (ITC), high resolution nuclear magnetic resonance (NMR), electron paramagnetic resonance (EPR), and small-angle neutron scattering (SANS) measurements. CP provided the thermodynamic information on the Gibbs free energy, enthalpy, entropy and heat capacity changes pertaining to the phase separation of the system at elevated temperature. The ITC and NMR self-diffusion measurements helped to understand the nature of the binding isotherms of SDS in the presence of L31 in terms of the formation of mixed aggregates and free SDS micelles in solution. EPR analysis provided the micro-viscosity of the spin probe 5-DSA in terms of rotational correlation time. The SANS study indicated the presence of prolate ellipsoidal mixed aggregates, whose size increased with the increasing addition of L31. At a large [L31], SANS also revealed the progressive decreasing size of the ellipsoidal mixed aggregates of SDS-L31 into nearly globular forms with the increasing SDS addition. Wrapping of the spherical SDS micelles by L31 was also corroborated from (13)C NMR and SANS measurements.

Shear flow control of cold and heated rectangular jets by mechanical tabs. Volume 1: Results and discussion

NASA Technical Reports Server (NTRS)

Brown, W. H.; Ahuja, K. K.

1989-01-01

The effects of mechanical protrusions on the jet mixing characteristics of rectangular nozzles for heated and unheated subsonic and supersonic jet plumes were studied. The characteristics of a rectangular nozzle of aspect ratio 4 without the mechanical protrusions were first investigated. Intrusive probes were used to make the flow measurements. Possible errors introduced by intrusive probes in making shear flow measurements were also examined. Several scaled sizes of mechanical tabs were then tested, configured around the perimeter of the rectangular jet. Both the number and the location of the tabs were varied. From this, the best configuration was selected. The conclusions derived were: (1) intrusive probes can produce significant errors in the measurements of the velocity of jets if they are large in diameter and penetrate beyond the jet center; (2) rectangular jets without tabs, compared to circular jets of the same exit area, provide faster jet mixing; and (3) further mixing enhancement is possible by using mechanical tabs.

Fast scaffolding with small independent mixed integer programs

PubMed Central

Salmela, Leena; Mäkinen, Veli; Välimäki, Niko; Ylinen, Johannes; Ukkonen, Esko

2011-01-01

Motivation: Assembling genomes from short read data has become increasingly popular, but the problem remains computationally challenging especially for larger genomes. We study the scaffolding phase of sequence assembly where preassembled contigs are ordered based on mate pair data. Results: We present MIP Scaffolder that divides the scaffolding problem into smaller subproblems and solves these with mixed integer programming. The scaffolding problem can be represented as a graph and the biconnected components of this graph can be solved independently. We present a technique for restricting the size of these subproblems so that they can be solved accurately with mixed integer programming. We compare MIP Scaffolder to two state of the art methods, SOPRA and SSPACE. MIP Scaffolder is fast and produces better or as good scaffolds as its competitors on large genomes. Availability: The source code of MIP Scaffolder is freely available at http://www.cs.helsinki.fi/u/lmsalmel/mip-scaffolder/. Contact: leena.salmela@cs.helsinki.fi PMID:21998153

Observations of condensation nuclei in the 1987 airborne Antarctic ozone experiment

NASA Technical Reports Server (NTRS)

Wilson, J. C.; Smith, S. D.; Ferry, G. V.; Loewenstein, M.

1988-01-01

The condensation nucleus counter (CNC) flown of the NASA ER-2 in the Airborne Antarctic Ozone Experiment provides a measurement of the number mixing ratio of particles which can be grown by exposure to supersaturated n-butyl alcohol vapor to diameters of a few microns. Such particles are referred to as condensation nuclei (CN). The ER-2 CNC was calibrated with aerosols of known size and concentration and was found to provide an accurate measure of the number concentration of particles larger than about 0.02 micron. Since the number distribution of stratospheric aerosols is usually dominated by particles less than a few tenths of micron in diameter, the upper cutoff of the ER-2 CNC has not been determined experimentally. However, theory suggests that the sampling and counting efficiency should remain near one for particles as large as 1 micron in diameter. Thus, the CN mixing ratio is usually a good measure of the mixing ratio of submicron particles.

Microstructure and Transparent Super-Hydrophobic Performance of Vacuum Cold-Sprayed Al2O3 and SiO2 Aerogel Composite Coating

NASA Astrophysics Data System (ADS)

Li, Jie; Zhang, Yu; Ma, Kai; Pan, Xi-De; Li, Cheng-Xin; Yang, Guan-Jun; Li, Chang-Jiu

2018-02-01

In this study, vacuum cold spraying was used as a simple and fast way to prepare transparent super-hydrophobic coatings. Submicrometer-sized Al2O3 powder modified by 1,1,2,2-tetrahydroperfluorodecyltriethoxysilane and mixed with hydrophobic SiO2 aerogel was employed for the coating deposition. The deposition mechanisms of pure Al2O3 powder and Al2O3-SiO2 mixed powder were examined, and the effects of powder structure on the hydrophobicity and light transmittance of the coatings were evaluated. The results showed that appropriate contents of SiO2 aerogel in the mixed powder could provide sufficient cushioning to the deposition of submicrometer Al2O3 powder during spraying. The prepared composite coating surface showed rough structures with a large number of submicrometer convex deposited particles, characterized by being super-hydrophobic. Also, the transmittance of the obtained coating was higher than 80% in the range of visible light.

The roles of dry convection, cloud-radiation feedback processes and the influence of recent improvements in the parameterization of convection in the GLA GCM

NASA Technical Reports Server (NTRS)

Sud, Y.; Molod, A.

1988-01-01

The Goddard Laboratory for Atmospheres GCM is used to study the sensitivity of the simulated July circulation to modifications in the parameterization of dry and moist convection, evaporation from falling raindrops, and cloud-radiation interaction. It is shown that the Arakawa-Schubert (1974) cumulus parameterization and a more realistic dry convective mixing calculation yielded a better intertropical convergence zone over North Africa than the previous convection scheme. It is found that the physical mechanism for the improvement was the upward mixing of PBL moisture by vigorous dry convective mixing. A modified rain-evaporation parameterization which accounts for raindrop size distribution, the atmospheric relative humidity, and a typical spatial rainfall intensity distribution for convective rain was developed and implemented. This scheme led to major improvements in the monthly mean vertical profiles of relative humidity and temperature, convective and large-scale cloudiness, rainfall distributions, and mean relative humidity in the PBL.

PROPERTIES IMPORTANT TO MIXING FOR WTP LARGE SCALE INTEGRATED TESTING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, D.; Martino, C.; Poirier, M.

2012-04-26

Large Scale Integrated Testing (LSIT) is being planned by Bechtel National, Inc. to address uncertainties in the full scale mixing performance of the Hanford Waste Treatment and Immobilization Plant (WTP). Testing will use simulated waste rather than actual Hanford waste. Therefore, the use of suitable simulants is critical to achieving the goals of the test program. External review boards have raised questions regarding the overall representativeness of simulants used in previous mixing tests. Accordingly, WTP requested the Savannah River National Laboratory (SRNL) to assist with development of simulants for use in LSIT. Among the first tasks assigned to SRNL wasmore » to develop a list of waste properties that matter to pulse-jet mixer (PJM) mixing of WTP tanks. This report satisfies Commitment 5.2.3.1 of the Department of Energy Implementation Plan for Defense Nuclear Facilities Safety Board Recommendation 2010-2: physical properties important to mixing and scaling. In support of waste simulant development, the following two objectives are the focus of this report: (1) Assess physical and chemical properties important to the testing and development of mixing scaling relationships; (2) Identify the governing properties and associated ranges for LSIT to achieve the Newtonian and non-Newtonian test objectives. This includes the properties to support testing of sampling and heel management systems. The test objectives for LSIT relate to transfer and pump out of solid particles, prototypic integrated operations, sparger operation, PJM controllability, vessel level/density measurement accuracy, sampling, heel management, PJM restart, design and safety margin, Computational Fluid Dynamics (CFD) Verification and Validation (V and V) and comparison, performance testing and scaling, and high temperature operation. The slurry properties that are most important to Performance Testing and Scaling depend on the test objective and rheological classification of the slurry (i.e., Newtonian or non-Newtonian). The most important properties for testing with Newtonian slurries are the Archimedes number distribution and the particle concentration. For some test objectives, the shear strength is important. In the testing to collect data for CFD V and V and CFD comparison, the liquid density and liquid viscosity are important. In the high temperature testing, the liquid density and liquid viscosity are important. The Archimedes number distribution combines effects of particle size distribution, solid-liquid density difference, and kinematic viscosity. The most important properties for testing with non-Newtonian slurries are the slurry yield stress, the slurry consistency, and the shear strength. The solid-liquid density difference and the particle size are also important. It is also important to match multiple properties within the same simulant to achieve behavior representative of the waste. Other properties such as particle shape, concentration, surface charge, and size distribution breadth, as well as slurry cohesiveness and adhesiveness, liquid pH and ionic strength also influence the simulant properties either directly or through other physical properties such as yield stress.« less

Nitrogen expander cycles for large capacity liquefaction of natural gas

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun; Choe, Kun Hyung

2014-01-01

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

A stand density management diagram for sawtimber-sized mixed upland central hardwoods

Treesearch

J.A., Jr. Kershaw; B.C. Fischer

1991-01-01

Data from 190 CFI plots located in southern and west-central Indiana are used to develop a stand density diagram for sawtimber-sized mixed upland hardwoods in the Central States. The stand density diagram utilizes the concepts of self-thinning to establish a maximum size-density curve, and the stocking standards of Gingrich (1967) to formulate imtermediate stocking...

Solute mixing regulates heterogeneity of mineral precipitation in porous media: Effect of Solute Mixing on Precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cil, Mehmet B.; Xie, Minwei; Packman, Aaron I.

Synchrotron X-ray microtomography was used to track the spatiotemporal evolution of mineral precipitation and the consequent alteration of the pore structure. Column experiments were conducted by injecting CaCl2 and NaHCO3 solutions into granular porous media either as a premixed supersaturated solution (external mixing) or as separate solutions that mixed within the specimen (internal mixing). The two mixing modes produced distinct mineral growth patterns. While internal mixing promoted transverse heterogeneity with precipitation at the mixing zone, external mixing favored relatively homogeneous precipitation along the flow direction. The impact of precipitation on pore water flow and permeability was assessed via 3-D flowmore » simulations, which indicated anisotropic permeability evolution for both mixing modes. Under both mixing modes, precipitation decreased the median pore size and increased the skewness of the pore size distribution. Such similar pore-scale evolution patterns suggest that the clogging of individual pores depends primarily on local supersaturation state and pore geometry.« less

Large scale Full QM-MD investigation of small peptides and insulin adsorption on ideal and defective TiO2 (1 0 0) surfaces. Influence of peptide size on interfacial bonds

NASA Astrophysics Data System (ADS)

Dubot, Pierre; Boisseau, Nicolas; Cenedese, Pierre

2018-05-01

Large biomolecule interaction with oxide surface has attracted a lot of attention because it drives behavior of implanted devices in the living body. To investigate the role of TiO2 surface structure on a large polypeptide (insulin) adsorption, we use a homemade mixed Molecular Dynamics-Full large scale Quantum Mechanics code. A specific re-parameterized (Ti) and globally convergent NDDO method fitted on high level ab initio method (coupled cluster CCSD(T) and DFT) allows us to safely describe the electronic structure of the whole insulin-TiO2 surface system (up to 4000 atoms). Looking specifically at carboxylate residues, we demonstrate in this work that specific interfacial bonds are obtained from the insulin/TiO2 system that are not observed in the case of smaller peptides (tripeptides, insulin segment chains with different configurations). We also demonstrate that a large part of the adsorption energy is compensated by insulin conformational energy changes and surface defects enhanced this trend. Large slab dimensions allow us to take into account surface defects that are actually beyond ab initio capabilities owing to size effect. These results highlight the influence of the surface structure on the conformation and therefore of the possible inactivity of an adsorbed polypeptides.

Large tree diameter distribution modelling using sparse airborne laser scanning data in a subtropical forest in Nepal

NASA Astrophysics Data System (ADS)

Rana, Parvez; Vauhkonen, Jari; Junttila, Virpi; Hou, Zhengyang; Gautam, Basanta; Cawkwell, Fiona; Tokola, Timo

2017-12-01

Large-diameter trees (taking DBH > 30 cm to define large trees) dominate the dynamics, function and structure of a forest ecosystem. The aim here was to employ sparse airborne laser scanning (ALS) data with a mean point density of 0.8 m-2 and the non-parametric k-most similar neighbour (k-MSN) to predict tree diameter at breast height (DBH) distributions in a subtropical forest in southern Nepal. The specific objectives were: (1) to evaluate the accuracy of the large-tree fraction of the diameter distribution; and (2) to assess the effect of the number of training areas (sample size, n) on the accuracy of the predicted tree diameter distribution. Comparison of the predicted distributions with empirical ones indicated that the large tree diameter distribution can be derived in a mixed species forest with a RMSE% of 66% and a bias% of -1.33%. It was also feasible to downsize the sample size without losing the interpretability capacity of the model. For large-diameter trees, even a reduction of half of the training plots (n = 250), giving a marginal increase in the RMSE% (1.12-1.97%) was reported compared with the original training plots (n = 500). To be consistent with these outcomes, the sample areas should capture the entire range of spatial and feature variability in order to reduce the occurrence of error.

Bis(aminoaryl) Carbon-Bridged Oligo(phenylenevinylene)s Expand the Limits of Electronic Couplings.

PubMed

Burrezo, Paula Mayorga; Lin, Nai-Ti; Nakabayashi, Koji; Ohkoshi, Shin-Ichi; Calzado, Eva M; Boj, Pedro G; Díaz García, María A; Franco, Carlos; Rovira, Concepciò; Veciana, Jaume; Moos, Michael; Lambert, Christoph; López Navarrete, Juan T; Tsuji, Hayato; Nakamura, Eiichi; Casado, Juan

2017-03-06

Carbon-bridged bis(aminoaryl) oligo(para-phenylenevinylene)s have been prepared and their optical, electrochemical, and structural properties analyzed. Their radical cations are class III and class II mixed-valence systems, depending on the molecular size, and they show electronic couplings which are among the largest for the self-exchange reaction of purely organic molecules. In their dication states, the antiferromagnetic coupling is progressively tuned with size from quinoidal closed-shell to open-shell biradicals. The data prove that the electronic coupling in the radical cations and the singlet-triplet gap in the dications show similar small attenuation factors, thus allowing charge/spin transfer over rather large distances. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Superhydrophobic and transparent coatings prepared by self-assembly of dual-sized silica particles

NASA Astrophysics Data System (ADS)

Xu, Qian-Feng; Wang, Jian-Nong

2010-06-01

Superhydrophobic and transparent coatings have been prepared by self-assembly of dual-sized silica particles from a mixed dispersion. The desirable micro/nano hierarchical structure for superhydrophobicity is constructed simply by adjusting the size and ratio of the dual-sized particles without organic/inorganic templates. The transparency of the prepared coatings is also researched, and the light scattering can be reduced by lowering the ratio of big sub-micro particles while the superhydrophobicity maintains unchanged. When nano particles with a diameter of 50 nm and sub-micro particles with a diameter of 350 nm are assembled, a superhydrophobic property with a water contact angle of 161° is achieved. Additionally, the coated glass is also very transparent. The highest transmittance of the coated glass can reach 85%. Compared to traditional colloid self-assembly approach, which often involves dozens of steps of layer-by-layer processing and organic/inorganic templates, the present approach is much simpler and has advantages for large-scale coating.

Solving a supply chain scheduling problem with non-identical job sizes and release times by applying a novel effective heuristic algorithm

NASA Astrophysics Data System (ADS)

Pei, Jun; Liu, Xinbao; Pardalos, Panos M.; Fan, Wenjuan; Wang, Ling; Yang, Shanlin

2016-03-01

Motivated by applications in manufacturing industry, we consider a supply chain scheduling problem, where each job is characterised by non-identical sizes, different release times and unequal processing times. The objective is to minimise the makespan by making batching and sequencing decisions. The problem is formalised as a mixed integer programming model and proved to be strongly NP-hard. Some structural properties are presented for both the general case and a special case. Based on these properties, a lower bound is derived, and a novel two-phase heuristic (TP-H) is developed to solve the problem, which guarantees to obtain a worst case performance ratio of ?. Computational experiments with a set of different sizes of random instances are conducted to evaluate the proposed approach TP-H, which is superior to another two heuristics proposed in the literature. Furthermore, the experimental results indicate that TP-H can effectively and efficiently solve large-size problems in a reasonable time.

Fabrication of large size alginate beads for three-dimensional cell-cluster culture

NASA Astrophysics Data System (ADS)

Zhang, Zhengtao; Ruan, Meilin; Liu, Hongni; Cao, Yiping; He, Rongxiang

2017-08-01

We fabricated large size alginate beads using a simple microfluidic device under a co-axial injection regime. This device was made by PDMS casting with a mold formed by small diameter metal and polytetrafluorothylene tubes. Droplets of 2% sodium alginate were generated in soybean oil through the device and then cross-linked in a 2% CaCl2 solution, which was mixed tween80 with at a concentration of 0.4 to 40% (w/v). Our results showed that the morphology of the produced alginate beads strongly depends on the tween80 concentration. With the increase of concentration of tween80, the shape of the alginate beads varied from semi-spherical to tailed-spherical, due to the decrease of interface tension between oil and cross-link solution. To access the biocompatibility of the approach, MCF-7 cells were cultured with the alginate beads, showing the formation of cancer cells clusters which might be useful for future studies.

The Case Mix of Patients Presenting with Full-Thickness Macular Holes and Progression before Surgery: Implications for Optimum Management.

PubMed

Madi, Haifa A; Dinah, Christiana; Rees, Jon; Steel, David H W

2015-01-01

Analysis of pre-operative spectral domain optical coherence tomography (SD-OCT) characteristics of full-thickness macular holes (FTMH) and effect on optimum management. We retrospectively reviewed SD-OCT characteristics of a consecutive cohort of patients waitlisted for FTMH surgery and categorized them by current evidence-based treatments. Out of the 106 holes analysed, 36 were small, 40 medium and 30 large. Initially, 33 holes had vitreomacular adhesion (VMA). 41 holes were analysed for change in characteristics with a median duration of 8 weeks between the scans. The number of small or medium holes decreased from 20 to 6 and that of large holes doubled. The number of holes with VMA halved. Smaller hole size (p = 0.014) and being phakic (p = 0.048) were associated with a larger increase in size. The strongest predictor of hole progression into a different surgical management category was the presence of VMA. FTMH characteristics can change significantly pre-operatively and affect optimal treatment choice.

Limited genomic consequences of mixed mating in the recently derived sister species pair, Collinsia concolor and Collinsia parryi.

PubMed

Salcedo, A; Kalisz, S; Wright, S I

2014-07-01

Highly selfing species often show reduced effective population sizes and reduced selection efficacy. Whether mixed mating species, which produce both self and outcross progeny, show similar patterns of diversity and selection remains less clear. Examination of patterns of molecular evolution and levels of diversity in species with mixed mating systems can be particularly useful for investigating the relative importance of linked selection and demographic effects on diversity and the efficacy of selection, as the effects of linked selection should be minimal in mixed mating populations, although severe bottlenecks tied to founder events could still be frequent. To begin to address this gap, we assembled and analysed the transcriptomes of individuals from a recently diverged mixed mating sister species pair in the self-compatible genus, Collinsia. The de novo assembly of 52 and 37 Mbp C. concolor and C. parryi transcriptomes resulted in ~40 000 and ~55 000 contigs, respectively, both with an average contig size ~945. We observed a high ratio of shared polymorphisms to fixed differences in the species pair and minimal differences between species in the ratio of synonymous to replacement substitutions or codon usage bias implying comparable effective population sizes throughout species divergence. Our results suggest that differences in effective population size and selection efficacy in mixed mating taxa shortly after their divergence may be minimal and are likely influenced by fluctuating mating systems and population sizes. © 2014 The Authors. Journal of Evolutionary Biology © 2014 European Society For Evolutionary Biology.

Characterization of mixing of suspension in a mechanically stirred precipitation system

NASA Astrophysics Data System (ADS)

Farkas, B.; Blickle, T.; Ulbert, Zs.; Hasznos-Nezdei, M.

1996-09-01

In the case of precipitational crystallization, the particle size distribution of the resulting product is greatly influenced by the mixing rate of the system. We have worked out a method of characterizing the mixing of precipitated suspensions by applying a function of mean residence time and particle size distribution. For the experiments a precipitated suspension of β-lactam-type antibiotic has been used in a mechanically stirred tank.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, R.V.

1999-02-02

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form, usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, R.V.

1997-12-30

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Platinum particle size and support effects in NO(x) mediated carbon oxidation over platinum catalysts.

PubMed

Villani, Kenneth; Vermandel, Walter; Smets, Koen; Liang, Duoduo; van Tendeloo, Gustaaf; Martens, Johan A

2006-04-15

Platinum metal was dispersed on microporous, mesoporous, and nonporous support materials including the zeolites Na-Y, Ba-Y, Ferrierite, ZSM-22, ETS-10, and AIPO-11, alumina, and titania. The oxidation of carbon black loosely mixed with catalyst powder was monitored gravimetrically in a gas stream containing nitric oxide, oxygen, and water. The carbon oxidation activity of the catalysts was found to be uniquely related to the Pt dispersion and little influenced by support type. The optimum dispersion is around 3-4% corresponding to relatively large Pt particle sizes of 20-40 nm. The carbon oxidation activity reflects the NO oxidation activity of the platinum catalyst, which reaches an optimum in the 20-40 nm Pt particle size range. The lowest carbon oxidation temperatures were achieved with platinum loaded ZSM-22 and AIPO-11 zeolite crystallites bearing platinum of optimum dispersion on their external surfaces.

Filter and Grid Resolution in DG-LES

NASA Astrophysics Data System (ADS)

Miao, Ling; Sammak, Shervin; Madnia, Cyrus K.; Givi, Peyman

2017-11-01

The discontinuous Galerkin (DG) methodology has proven very effective for large eddy simulation (LES) of turbulent flows. Two important parameters in DG-LES are the grid resolution (h) and the filter size (Δ). In most previous work, the filter size is usually set to be proportional to the grid spacing. In this work, the DG method is combined with a subgrid scale (SGS) closure which is equivalent to that of the filtered density function (FDF). The resulting hybrid scheme is particularly attractive because a larger portion of the resolved energy is captured as the order of spectral approximation increases. Different cases for LES of a three-dimensional temporally developing mixing layer are appraised and a systematic parametric study is conducted to investigate the effects of grid resolution, the filter width size, and the order of spectral discretization. Comparative assessments are also made via the use of high resolution direct numerical simulation (DNS) data.

The Flow Induced by the Coalescence of Two Initially Stationary Drops

NASA Technical Reports Server (NTRS)

Nobari, M. R.; Tryggvason, G.

1994-01-01

The coalescence of two initially stationary drops of different size is investigated by solving the unsteady, axisymmetric Navier-Stokes equations numerically, using a Front-Tracking/Finite Difference method. Initially, the drops are put next to each other and the film between them ruptured. Due to surface tension forces, the drops coalesce rapidly and the fluid from the small drop is injected into the larger one. For low nondimensional viscosity, or Ohnesorge number, little mixing takes place and the small drop fluid forms a blob near the point where the drops touched initially. For low Ohnesorge number, on the other hand, the small drop forms a jet that penetrates far into the large drop. The penetration depth also depends on the size of the drops and shows that for a given fluid of sufficiently low viscosity, there is a maximum penetration depth for intermediate size ratios.

Durable regenerable sorbent pellets for removal of hydrogen sulfide from coal gas

DOEpatents

Siriwardane, Ranjani V.

1997-01-01

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Durable regenerable sorbent pellets for removal of hydrogen sulfide coal gas

DOEpatents

Siriwardane, Ranjani V.

1999-01-01

Pellets for removing hydrogen sulfide from a coal gasification stream at an elevated temperature are prepared in durable form, usable over repeated cycles of absorption and regeneration. The pellets include a material reactive with hydrogen sulfide, in particular zinc oxide, a binder, and an inert material, in particular calcium sulfate (drierite), having a particle size substantially larger than other components of the pellets. A second inert material and a promoter may also be included. Preparation of the pellets may be carried out by dry, solid-state mixing of components, moistening the mixture, and agglomerating it into pellets, followed by drying and calcining. Pellet size is selected, depending on the type of reaction bed for which the pellets are intended. The use of inert material with a large particle size provides a stable pellet structure with increased porosity, enabling effective gas contact and prolonged mechanical durability.

Error and bias in size estimates of whale sharks: implications for understanding demography.

PubMed

Sequeira, Ana M M; Thums, Michele; Brooks, Kim; Meekan, Mark G

2016-03-01

Body size and age at maturity are indicative of the vulnerability of a species to extinction. However, they are both difficult to estimate for large animals that cannot be restrained for measurement. For very large species such as whale sharks, body size is commonly estimated visually, potentially resulting in the addition of errors and bias. Here, we investigate the errors and bias associated with total lengths of whale sharks estimated visually by comparing them with measurements collected using a stereo-video camera system at Ningaloo Reef, Western Australia. Using linear mixed-effects models, we found that visual lengths were biased towards underestimation with increasing size of the shark. When using the stereo-video camera, the number of larger individuals that were possibly mature (or close to maturity) that were detected increased by approximately 10%. Mean lengths calculated by each method were, however, comparable (5.002 ± 1.194 and 6.128 ± 1.609 m, s.d.), confirming that the population at Ningaloo is mostly composed of immature sharks based on published lengths at maturity. We then collated data sets of total lengths sampled from aggregations of whale sharks worldwide between 1995 and 2013. Except for locations in the East Pacific where large females have been reported, these aggregations also largely consisted of juveniles (mean lengths less than 7 m). Sightings of the largest individuals were limited and occurred mostly prior to 2006. This result highlights the urgent need to locate and quantify the numbers of mature male and female whale sharks in order to ascertain the conservation status and ensure persistence of the species.

Mobilization of Cr(VI) from chromite ore processing residue through acid treatment.

PubMed

Tinjum, James M; Benson, Craig H; Edil, Tuncer B

2008-02-25

Batch leaching studies on chromite ore processing residue (COPR) were performed using acids to investigate leaching of hexavalent chromium, Cr(VI), with respect to particle size, reaction time, and type of acid (HNO(3) and H(2)SO(4)). Aqueous Cr(VI) is maximized at approximately 0.04 mol Cr(VI) per kg of dry COPR at pH 7.6-8.1. Cr(VI) mobilized more slowly for larger particles, and the pH increased with time and increased more rapidly for smaller particles, suggesting that rate limitations occur in the solid phase. With H(2)SO(4), the pH stabilized at a higher value (8.8 for H(2)SO(4) vs. 8.0 for HNO(3)) and more rapidly (16 h vs. 30 h), and the differences in pH for different particle sizes were smaller. The acid neutralization capacity (ANC) of COPR is very large (8 mol HNO(3) per kg of dry COPR for a stable eluate pH of 7.5). Changes to the elemental and mineralogical composition and distribution in COPR particles after mixing with acid indicate that Cr(VI)-bearing solids dissolved. However, concentrations of Cr(VI) >2800 mg kg(-1) (>50% of the pre-treatment concentration) were still found after mixing with acid, regardless of the particle size, reaction time, or type of acid used. The residual Cr(VI) appears to be partially associated with poorly-ordered Fe and Al oxyhydroxides that precipitated in the interstitial areas of COPR particles. Remediation strategies that use HNO(3) or H(2)SO(4) to neutralize COPR or to maximize Cr(VI) in solution are likely to require extensive amounts of acid, may not mobilize all of the Cr(VI), and may require extended contact time, even under well-mixed conditions.

Do rivermouths alter nutrient and seston delivery to the nearshore?

USGS Publications Warehouse

Larson, James H.; Frost, Paul C.; Vallazza, Jon M.; Nelson, John; Richardson, William B.

2016-01-01

Tributary inputs to lakes and seas are often measured at riverine gages, upstream of lentic influence. Between these riverine gages and the nearshore zones of large waterbodies lie rivermouths, which may retain, transform and contribute materials to the nearshore zone. However, the magnitude and timing of these rivermouth effects have rarely been measured.During the summer of 2011, 23 tributary systems of the Laurentian Great Lakes were sampled from river to nearshore for dissolved and particulate carbon (C), nitrogen (N) and phosphorus (P) concentrations, as well as bulk seston and chlorophyll a concentrations. Three locations per system were sampled: in the upstream river, in the nearshore zone and at the outflow from the rivermouth to the lake. Using stable oxygen isotopes, a water-mixing model was developed to estimate the nutrient concentration that would occur at the rivermouth if mixing was strictly conservative (i.e. if no processing occurred within the rivermouth). Deviations between these conservative mixing estimates and measured nutrient concentrations were identified as rivermouth effects on nutrient concentrations.Rivermouths had higher concentration of C and P than nearshore areas and more chlorophyll athan upstream river waters. Compared to the conservative mixing model, rivermouths as a class appeared to be summer-time sources of N, P and chlorophyll a. Substantial among rivermouth variation occurred both in the effect size and direction for all constituents.Using principal component analysis, two groups of rivermouths were identified: rivermouths that had a large effect on most constituents and those that had very little effect on any of the measured constituents. ‘High-effect’ rivermouths had more abundant upstream croplands, which were presumably the sources of inorganic nutrients. Cross-validated models built using characteristics of the rivermouth were not good predictors of variation in rivermouth effects on most constituents.For consumers feeding on seston and microbes and vascular autotrophs directly taking up dissolved nutrients, rivermouths are more resource-rich than upstream riverine or nearby Great Lakes waters. Given declines over time in open-lake productivity within the Great Lakes, rivermouths may contribute more productivity than their size would suggest to the Great Lakes food web.

When is an INP not an INP?

NASA Astrophysics Data System (ADS)

Simpson, Emma; Connolly, Paul; McFiggans, Gordon

2016-04-01

Processes such as precipitation and radiation depend on the concentration and size of different hydrometeors within clouds therefore it is important to accurately predict them in weather and climate models. A large fraction of clouds present in our atmosphere are mixed phase; contain both liquid and ice particles. The number of drops and ice crystals present in mixed phase clouds strongly depends on the size distribution of aerosols. Cloud condensation nuclei (CCN), a subset of atmospheric aerosol particles, are required for liquid drops to form in the atmosphere. These particles are ubiquitous in the atmosphere. To nucleate ice particles in mixed phase clouds ice nucleating particles (INP) are required. These particles are rarer than CCN. Here we investigate the case where CCN and INPs are in direct competition with each other for water vapour within a cloud. Focusing on the immersion and condensation modes of freezing (where an INP must be immersed within a liquid drop before it can freeze) we show that the presence of CCN can suppress the formation of ice. CCN are more hydrophilic than IN and as such are better able to compete for water vapour than, typically insoluble, INPs. Therefore water is more likely to condense onto a CCN than INP, leaving the INP without enough condensed water on it to be able to freeze in the immersion or condensation mode. The magnitude of this suppression effect strongly depends on a currently unconstrained quantity. Here we refer to this quantity as the critical mass of condensed water required for freezing, Mwc. Mwc is the threshold amount of water that must be condensed onto a INP before it can freeze in the immersion or condensation mode. Using the detailed cloud parcel model, Aerosol-Cloud-Precipiation-Interaction Model (ACPIM), developed at the University of Manchester we show that if only a small amount of water is required for freezing there is little suppression effect and if a large amount of water is required there is a large suppression effect. In this poster possible ways to constrain Mwc are discussed as well as conditions where the suppression effect is likely to be greatest. Key Words: Clouds, aerosol, CCN, IN, modelling

XPS Spectra Analysis of Ti2+, Ti3+ Ions and Dye Photodegradation Evaluation of Titania-Silica Mixed Oxide Nanoparticles

NASA Astrophysics Data System (ADS)

Chinh, Vu Duc; Broggi, Alessandra; Di Palma, Luca; Scarsella, Marco; Speranza, Giorgio; Vilardi, Giorgio; Thang, Pham Nam

2018-04-01

TiO2-SiO2 mixed oxides have been prepared by the sol-gel technique from tetrabutyl orthotitanate and tetraethyl orthosilicate. The prepared materials were characterized by x-ray diffraction, scanning electron microscopy, energy dispersive x-ray spectroscopy, nitrogen physisorption, Fourier-transform infrared spectroscopy (FT-IR) and x-ray photoelectron spectroscopy (XPS). The results indicate that the TiO2-SiO2 mixed oxides have a large surface area and a nanoscale size. FT-IR spectra show that Ti atoms are bonded to silica by oxygen bridging atoms in Ti-O-Si bonds. The titanium valence states in TiO2-SiO2 mixed oxides were investigated by XPS, and their spectra report the presence of Ti2+ and Ti3+ cations for high silica concentration, suggesting the formation of oxygen vacancies. The photocatalytic activity of the prepared materials has been evaluated for the photodegradation of methylene blue (MB). The mixed oxides were activated by means of a UV light source, and the concentration of MB was monitored by UV-Vis spectroscopy. The synthesized TiO2-SiO2 shows significantly higher MB removal efficiency in comparison with that of the commercial TiO2 Degussa, P25.

Palaeoenvironmental implication of grain-size compositions of terrace deposits on the western Chinese Loess Plateau

NASA Astrophysics Data System (ADS)

Liu, Xingxing; Sun, Youbin; Vandenberghe, Jef; Li, Ying; An, Zhisheng

2018-06-01

Sedimentary sequences that developed on river terraces have been widely investigated to reconstruct high-resolution palaeoclimatic changes since the last deglaciation. However, frequent changes in sedimentary facies make palaeoenvironmental interpretation of grain-size variations relatively complicated. In this paper, we employed multiple grain-size parameters to discriminate the sedimentary characteristics of aeolian and fluvial facies in the Dadiwan (DDW) section on the western Chinese Loess Plateau. We found that wind and fluvial dynamics have quite different impacts on the grain-size compositions, with distinctive imprints on the distribution pattern. By using a lognormal distribution fitting approach, two major grain-size components sensitive to aeolian and fluvial processes, respectively, were distinguished from the grain-size compositions of the DDW terrace deposits. The fine grain-size component (GSC2) represents mixing of long-distance aeolian and short-distance fluvial inputs, whilst the coarse grain-size component (GSC3) is mainly transported by wind from short-distance sources. Thus GSC3 can be used to infer the wind intensity. Grain-size variations reveal that the wind intensity experienced a stepwise shift from large-amplitude variations during the last deglaciation to small-amplitude oscillations in the Holocene, corresponding well to climate changes from regional to global context.

Correlation of size and type of modic types 1 and 2 lesions with clinical symptoms: a descriptive study in a subgroup of patients with chronic low back pain on the basis of a university hospital patient sample.

PubMed

Kääpä, Eeva; Luoma, Katariina; Pitkäniemi, Janne; Kerttula, Liisa; Grönblad, Mats

2012-01-15

Intensity of pain and level of disability (Oswestry Disability Index [ODI]) were compared with the relative size of Modic type 1 (M1) and Modic type 2 (M2) lesions. Clinical symptoms of patients having mixed M1-M2 lesion (n = 49) were compared with patients having a "pure" M1 lesion (n = 13). To determine the relation of the sizes of M1 and M2 lesions and the type of Modic lesion (mixed M1-M2 or pure M1 lesion) with intensity of low back pain and level of perceived disability. Endplate signal abnormalities, particularly M1 changes indicating edema and inflammation, have been suggested to play an important role in the etiopathogenesis of a subgroup of patients with nonspecific chronic low back pain (CLBP). However, their association with clinical symptoms has not been studied in detail previously. Sixty-two CLBP patients with a large M1 lesion were selected from CLBP patients who were sent for the first time for standard lumbar spine magnetic resonance imaging at a university hospital. To exclude other causes of CLBP, as far as possible, strict exclusion criteria were used: any specific back disease, even a slight nerve root compression, a recent or major spine operation, or age older than 65 years. The relative sizes of M1 and M2 lesions were visually estimated from sagittal images for comparison with clinical symptoms. The majority of patients (91.9%; 57 of 62) had an M1 lesion at a single level, 92% of the lesions being at L4-L5 or L5-S1 level. Forty-nine patients (79.0%) had a mixed M1-M2 lesion, and 13 (21.0%) had a pure M1 lesion. The mean of the pain intensity score was 6.2, and, correspondingly, the Oswestry Disability Index was 30.4. The mean relative sagittal area of the largest M1 lesion was 24.6% (SD = 16.2), and that of the M2 lesion was 10.9% (SD = 11.6). Neither the pain intensity nor the ODI scores were found to correlate with the largest relative size of the M1 lesion. The patients with "pure" M1 lesion had statistically significantly more clinical symptoms than patients having a mixed M1-M2 lesion. We conclude that the size of M1 lesion does not directly correlate with the clinical symptoms but that the type of Modic lesion is more important. This study supports the previous observations that when the inflammatory process turns to the mixed M1-M2 lesions, clinical symptoms decrease.

TOWARDS ICE FORMATION CLOSURE IN MIXED-PHASE BOUNDARY LAYER CLOUDS DURING ISDAC

NASA Astrophysics Data System (ADS)

Avramov, A.; Ackerman, A. S.; Fridlind, A. M.; van Diedenhoven, B.; Korolev, A. V.

2009-12-01

Mixed-phase stratus clouds are ubiquitous in the Arctic during the winter and transition seasons. Despite their important role in various climate feedback mechanisms they are not well understood and are difficult to represent faithfully in cloud models. In particular, models of all types experience difficulties reproducing observed ice concentrations and liquid/ice water partitioning in these clouds. Previous studies have demonstrated that simulated ice concentrations and ice water content are critically dependent on ice nucleation modes and ice crystal habit assumed in simulations. In this study we use large-eddy simulations with size-resolved microphysics to determine whether uncertainties in ice nucleus concentrations, ice nucleation mechanisms, ice crystal habits and large-scale forcing are sufficient to account for the difference between simulated and observed quantities. We present results of simulations of two case studies based on observations taken during the recent Indirect and Semi-Direct Aerosol Campaign (ISDAC) on April 8 and 26, 2008. The model simulations are evaluated through extensive comparison with in-situ observations and ground-based remote sensing measurements.

Influence of non-homogeneous mixing on final epidemic size in a meta-population model.

PubMed

Cui, Jingan; Zhang, Yanan; Feng, Zhilan

2018-06-18

In meta-population models for infectious diseases, the basic reproduction number [Formula: see text] can be as much as 70% larger in the case of preferential mixing than that in homogeneous mixing [J.W. Glasser, Z. Feng, S.B. Omer, P.J. Smith, and L.E. Rodewald, The effect of heterogeneity in uptake of the measles, mumps, and rubella vaccine on the potential for outbreaks of measles: A modelling study, Lancet ID 16 (2016), pp. 599-605. doi: 10.1016/S1473-3099(16)00004-9 ]. This suggests that realistic mixing can be an important factor to consider in order for the models to provide a reliable assessment of intervention strategies. The influence of mixing is more significant when the population is highly heterogeneous. In this paper, another quantity, the final epidemic size ([Formula: see text]) of an outbreak, is considered to examine the influence of mixing and population heterogeneity. Final size relation is derived for a meta-population model accounting for a general mixing. The results show that [Formula: see text] can be influenced by the pattern of mixing in a significant way. Another interesting finding is that, heterogeneity in various sub-population characteristics may have the opposite effect on [Formula: see text] and [Formula: see text].

Hierarchical creep cavity formation in an ultramylonite and implications for phase mixing

NASA Astrophysics Data System (ADS)

Gilgannon, James; Fusseis, Florian; Menegon, Luca; Regenauer-Lieb, Klaus; Buckman, Jim

2017-12-01

Establishing models for the formation of well-mixed polyphase domains in ultramylonites is difficult because the effects of large strains and thermo-hydro-chemo-mechanical feedbacks can obscure the transient phenomena that may be responsible for domain production. We use scanning electron microscopy and nanotomography to offer critical insights into how the microstructure of a highly deformed quartzo-feldspathic ultramylonite evolved. The dispersal of monomineralic quartz domains in the ultramylonite is interpreted to be the result of the emergence of synkinematic pores, called creep cavities. The cavities can be considered the product of two distinct mechanisms that formed hierarchically: Zener-Stroh cracking and viscous grain-boundary sliding. In initially thick and coherent quartz ribbons deforming by grain-size-insensitive creep, cavities were generated by the Zener-Stroh mechanism on grain boundaries aligned with the YZ plane of finite strain. The opening of creep cavities promoted the ingress of fluids to sites of low stress. The local addition of a fluid lowered the adhesion and cohesion of grain boundaries and promoted viscous grain-boundary sliding. With the increased contribution of viscous grain-boundary sliding, a second population of cavities formed to accommodate strain incompatibilities. Ultimately, the emergence of creep cavities is interpreted to be responsible for the transition of quartz domains from a grain-size-insensitive to a grain-size-sensitive rheology.

Synthesis, stabilization, and characterization of metal nanoparticles

NASA Astrophysics Data System (ADS)

White, Gregory Von, II

Wet chemical synthesis techniques offer the ability to control various nanoparticle characteristics including size, shape, dispersibility in both aqueous and organic solvents, and tailored surface chemistries appropriate for different applications. Large quantities of stabilizing ligands or surfactants are often required during synthesis to achieve these nanoparticle characteristics. Unfortunately, excess reaction byproducts, surfactants, and ligands remaining in solution after nanoparticle synthesis can impede application, and therefore post-synthesis purification must be employed. A liquid-liquid solvent/antisolvent pair (typically ethanol/toluene or ethanol/hexane for gold nanoparticles, GNPs) can be used to both purify and size-selectively fractionate hydrophobically modified nanoparticles. Alternatively, carbon dioxide may be used in place of a liquid antisolvent, a "green" approach, enabling both nanoparticle purification and size-selective fractionation while simultaneously eliminating mixed solvent waste and allowing solvent recycle. We have used small-angle neutron scattering (SANS) to investigate the ligand structure and composition response of alkanethiol modified gold and silver nanoparticles at varying anti-solvent conditions (CO2 or ethanol). The ligand lengths and ligand solvation for alkanethiol gold and silver NPs were found to decrease with increased antisolvent concentrations directly impacting their dispersibility in solution. Calculated Flory-Huggins interaction parameters support our SANS study for dodecanethiol dispersibility in the mixed organic solvents. This research has led to a greater understanding of the liquid-liquid precipitation process for metal nanoparticles, and provides critical results for future interaction energy modeling.

Field management of asphalt concrete mixes.

DOT National Transportation Integrated Search

1988-01-01

Marshall properties were determined on mixes from three different contractors each producing a 1/2-in and a 3/4-in top-sized aggregate mix. From these data, statistical analyses were made to determine differences among contractors and between mix typ...

Multiphase chemistry in a microphysical radiation fog model—A numerical study

NASA Astrophysics Data System (ADS)

Bott, Andreas; Carmichael, Gregory R.

A microphysical radiation fog model is coupled with a detailed chemistry module to simulate chemical reactions in the gas phase and in fog water during a radiation fog event. In the chemical part of the model the microphysical particle spectrum is subdivided into three size classes corresponding to non-activated aerosol particles, small and large fog droplets. Chemical reactions in the liquid phase are separately calculated in the small and in the large droplet size class. The impact of the chemical constitution of activated aerosols on fogwater chemistry is considered in the model simulations. The mass transfer of chemical species between the gas phase and the two liquid phases is treated in detail by solving the corresponding coupled differential equation system. The model also accounts for concentration changes of gas-phase and aqueous-phase chemical species which are induced by turbulence, gravitational settling and by evaporation/condensation processes. Numerical results demonstrate that fogwater chemistry is strongly controlled by dynamic processes, i.e. the vertical growth of the fog, turbulent mixing processes and the gravitational settling of the particles. The concentrations of aqueous-phase chemical species are different in the two droplet size classes. Reactands with lower water solubility are mainly found in the large droplet size class because the characteristic time for their mass transfer from the gas phase into the liquid phase is essentially longer than the characteristic time for the formation of large fog droplets. Species with high water solubility are rapidly transferred into the small fog droplets and are then washed out by wet deposition before these particles grow further to form large droplets. Thus, the concentrations of the major ions (NO 3-, NH 4+) are much higher in small than in large droplets, yielding distinctly lower pH values of the small particles. In the present study the reaction of sulfur with H 2O 2 and the Fe(III)-catalysed autoxidation of S(IV) are the major S(VI) producing mechanisms in fog water. Most of the time the sulfur oxidation rates are higher in the large than in the small droplets. Fogwater deposition by gravitational settling occurs mainly in the large droplet size class. However, since in the small droplets the concentrations of chemical species with very good water solubility are relatively high, in both droplet size classes the total wet deposition of these reactands is of the same order of magnitude.

Statistical characterization of planar two-dimensional Rayleigh-Taylor mixing layers

NASA Astrophysics Data System (ADS)

Sendersky, Dmitry

2000-10-01

The statistical evolution of a planar, randomly perturbed fluid interface subject to Rayleigh-Taylor instability is explored through numerical simulation in two space dimensions. The data set, generated by the front-tracking code FronTier, is highly resolved and covers a large ensemble of initial perturbations, allowing a more refined analysis of closure issues pertinent to the stochastic modeling of chaotic fluid mixing. We closely approach a two-fold convergence of the mean two-phase flow: convergence of the numerical solution under computational mesh refinement, and statistical convergence under increasing ensemble size. Quantities that appear in the two-phase averaged Euler equations are computed directly and analyzed for numerical and statistical convergence. Bulk averages show a high degree of convergence, while interfacial averages are convergent only in the outer portions of the mixing zone, where there is a coherent array of bubble and spike tips. Comparison with the familiar bubble/spike penetration law h = alphaAgt 2 is complicated by the lack of scale invariance, inability to carry the simulations to late time, the increasing Mach numbers of the bubble/spike tips, and sensitivity to the method of data analysis. Finally, we use the simulation data to analyze some constitutive properties of the mixing process.

Local Optical Closure Using Single Particle Mixing State Observations during the 2010 DOE CARES Campaign

NASA Astrophysics Data System (ADS)

Zaveri, R. A.; Arnott, W. P.; Atkinson, D. B.; Barnard, J.; Beranek, J.; Cappa, C. D.; Chand, D.; Dubey, M. K.; Easter, R. C.; Flowers, B. A.; Gyawali, M. S.; Jobson, B. T.; Pekour, M. S.; Riemer, N. S.; Subramanian, R.; Song, C.; Zelenyuk, A.

2011-12-01

Atmospheric black carbon (BC) particles readily absorb both upwelling and downwelling broadband radiation and are thought to be second only to CO2 in contributing to global warming. However large uncertainties still exist in the global estimates of BC radiative forcing, which depend not only on our ability to accurately simulate the global loading and distribution of BC, but also on the precise knowledge of the mixing state and morphology of BC particles due to aging. To this end, one of the objectives of the Carbonaceous Aerosols and Radiative Effects Study (CARES) conducted in Sacramento, CA, during June 2010 was to investigate the evolution of urban BC particles and the associated optical properties, with the overarching goal of improving their process-level model representations. The daytime Sacramento urban plume was routinely transported to the northeast into the Sierra Nevada foothills area rich in biogenic emissions, and the aged aerosols were often recirculated back into the urban area the next morning. The CARES campaign observational strategy was designed to take advantage of this flow pattern by setting up two observation supersites - one located within the Sacramento urban area, referred to as the "T0 site," and another located about 24 km to the northeast in Cool, CA, a small town in the rural foothills area, referred to as the "T1 site." BC size distribution and mixing state were measured at both the sites with single particle soot photometry (SP2). The single particle mass spectrometer SPLAT II was also deployed at the T0 site to characterize the size, composition (mixing state), density, and morphology of BC and non-BC containing particles. Non-refractory aerosol species were measured by Aerodyne aerosol mass spectrometer (AMS). Aerosol light absorption and scattering (or extinction) at multiple wavelengths were measured using several techniques, including photoacoustic, cavity ring-down, nephelometer as well as the filter-based particle/soot absorption photometer (PSAP). Other supporting measurements include aerosol size distribution and key trace gases (NOx, NOy, O3, and volatile organic compounds). The combined data thus provides a unique opportunity to characterize BC aging and its effect on optical properties. In this paper, we will present results from a local optical closure study for selected 10-minute samples at the T0 urban site using the particle-resolved version of the comprehensive aerosol model MOSAIC coupled to a shell/core Mie code. Sensitivity of the predicted optical properties to various measurements and model representations of particle composition, mixing state, size bin resolution, and refractive indices will be examined.

Passive Mixing Capabilities of Micro- and Nanofibres When Used in Microfluidic Systems.

PubMed

Matlock-Colangelo, Lauren; Colangelo, Nicholas W; Fenzl, Christoph; Frey, Margaret W; Baeumner, Antje J

2016-08-05

Nanofibres are increasingly being used in the field of bioanalytics due to their large surface-area-to-volume ratios and easy-to-functionalize surfaces. To date, nanofibres have been studied as effective filters, concentrators, and immobilization matrices within microfluidic devices. In addition, they are frequently used as optical and electrochemical transduction materials. In this work, we demonstrate that electrospun nanofibre mats cause appreciable passive mixing and therefore provide dual functionality when incorporated within microfluidic systems. Specifically, electrospun nanofibre mats were integrated into Y-shaped poly(methyl methacrylate) microchannels and the degree of mixing was quantified using fluorescence microscopy and ImageJ analysis. The degree of mixing afforded in relationship to fibre diameter, mat height, and mat length was studied. We observed that the most mixing was caused by small diameter PVA nanofibres (450-550 nm in diameter), producing up to 71% mixing at the microchannel outlet, compared to up to 51% with polystyrene microfibres (0.8-2.7 μm in diameter) and 29% mixing in control channels containing no fibres. The mixing afforded by the PVA nanofibres is caused by significant inhomogeneity in pore size and distribution leading to percolation. As expected, within all the studies, fluid mixing increased with fibre mat height, which corresponds to the vertical space of the microchannel occupied by the fibre mats. Doubling the height of the fibre mat led to an average increase in mixing of 14% for the PVA nanofibres and 8% for the PS microfibres. Overall, mixing was independent of the length of the fibre mat used (3-10 mm), suggesting that most mixing occurs as fluid enters and exits the fibre mat. The mixing effects observed within the fibre mats were comparable to or better than many passive mixers reported in literature. Since the nanofibre mats can be further functionalized to couple analyte concentration, immobilization, and detection with enhanced fluid mixing, they are a promising nanomaterial providing dual-functionality within lab-on-a-chip devices.

Passive Mixing Capabilities of Micro- and Nanofibres When Used in Microfluidic Systems

PubMed Central

Matlock-Colangelo, Lauren; Colangelo, Nicholas W.; Fenzl, Christoph; Frey, Margaret W.; Baeumner, Antje J.

2016-01-01

Nanofibres are increasingly being used in the field of bioanalytics due to their large surface-area-to-volume ratios and easy-to-functionalize surfaces. To date, nanofibres have been studied as effective filters, concentrators, and immobilization matrices within microfluidic devices. In addition, they are frequently used as optical and electrochemical transduction materials. In this work, we demonstrate that electrospun nanofibre mats cause appreciable passive mixing and therefore provide dual functionality when incorporated within microfluidic systems. Specifically, electrospun nanofibre mats were integrated into Y-shaped poly(methyl methacrylate) microchannels and the degree of mixing was quantified using fluorescence microscopy and ImageJ analysis. The degree of mixing afforded in relationship to fibre diameter, mat height, and mat length was studied. We observed that the most mixing was caused by small diameter PVA nanofibres (450–550 nm in diameter), producing up to 71% mixing at the microchannel outlet, compared to up to 51% with polystyrene microfibres (0.8–2.7 μm in diameter) and 29% mixing in control channels containing no fibres. The mixing afforded by the PVA nanofibres is caused by significant inhomogeneity in pore size and distribution leading to percolation. As expected, within all the studies, fluid mixing increased with fibre mat height, which corresponds to the vertical space of the microchannel occupied by the fibre mats. Doubling the height of the fibre mat led to an average increase in mixing of 14% for the PVA nanofibres and 8% for the PS microfibres. Overall, mixing was independent of the length of the fibre mat used (3–10 mm), suggesting that most mixing occurs as fluid enters and exits the fibre mat. The mixing effects observed within the fibre mats were comparable to or better than many passive mixers reported in literature. Since the nanofibre mats can be further functionalized to couple analyte concentration, immobilization, and detection with enhanced fluid mixing, they are a promising nanomaterial providing dual-functionality within lab-on-a-chip devices. PMID:27527184

Method of making bonded or sintered permanent magnets

DOEpatents

McCallum, R.W.; Dennis, K.W.; Lograsso, B.K.; Anderson, I.E.

1993-08-31

An isotropic permanent magnet is made by mixing a thermally responsive, low viscosity binder and atomized rare earth-transition metal (e.g., iron) alloy powder having a carbon-bearing (e.g., graphite) layer thereon that facilitates wetting and bonding of the powder particles by the binder. Prior to mixing with the binder, the atomized alloy powder may be sized or classified to provide a particular particle size fraction having a grain size within a given relatively narrow range. A selected particle size fraction is mixed with the binder and the mixture is molded to a desired complex magnet shape. A molded isotropic permanent magnet is thereby formed. A sintered isotropic permanent magnet can be formed by removing the binder from the molded mixture and thereafter sintering to full density.

Method of making bonded or sintered permanent magnets

DOEpatents

McCallum, R.W.; Dennis, K.W.; Lograsso, B.K.; Anderson, I.E.

1995-11-28

An isotropic permanent magnet is made by mixing a thermally responsive, low viscosity binder and atomized rare earth-transition metal (e.g., iron) alloy powder having a carbon-bearing (e.g., graphite) layer thereon that facilitates wetting and bonding of the powder particles by the binder. Prior to mixing with the binder, the atomized alloy powder may be sized or classified to provide a particular particle size fraction having a grain size within a given relatively narrow range. A selected particle size fraction is mixed with the binder and the mixture is molded to a desired complex magnet shape. A molded isotropic permanent magnet is thereby formed. A sintered isotropic permanent magnet can be formed by removing the binder from the molded mixture and thereafter sintering to full density. 14 figs.

Method of making bonded or sintered permanent magnets

DOEpatents

McCallum, R. William; Dennis, Kevin W.; Lograsso, Barbara K.; Anderson, Iver E.

1995-11-28

An isotropic permanent magnet is made by mixing a thermally responsive, low viscosity binder and atomized rare earth-transition metal (e.g., iron) alloy powder having a carbon-bearing (e.g., graphite) layer thereon that facilitates wetting and bonding of the powder particles by the binder. Prior to mixing with the binder, the atomized alloy powder may be sized or classified to provide a particular particle size fraction having a grain size within a given relatively narrow range. A selected particle size fraction is mixed with the binder and the mixture is molded to a desired complex magnet shape. A molded isotropic permanent magnet is thereby formed. A sintered isotropic permanent magnet can be formed by removing the binder from the molded mixture and thereafter sintering to full density.

Size-controlled fabrication of zein nano/microparticles by modified anti-solvent precipitation with/without sodium caseinate

PubMed Central

Li, Feng; Chen, Yan; Liu, Shubo; Qi, Jian; Wang, Weiying; Wang, Chenhua; Zhong, Ruiyue; Chen, Zhijun; Li, Xiaoming; Guan, Yuanzhou; Kong, Wei; Zhang, Yong

2017-01-01

Zein-based nano/microparticles have been demonstrated to be promising carrier systems for both the food industry and biomedical applications. However, the fabrication of size-controlled zein particles has been a challenging issue. In this study, a modified anti-solvent precipitation method was developed, and the effects of various factors, such as mixing method, solvent/anti-solvent ratio, temperature, zein concentrations and the presence of sodium caseinate (SC) on properties of zein particles were investigated. Evidence is presented that, among the previously mentioned factors, the mixing method, especially mixing rate, could be used as an effective parameter to control the size of zein particles without changing other parameters. Moreover, through fine-tuning the mixing rate together with zein concentration, particles with sizes ranging from nanometers to micrometers and low polydispersity index values could be easily obtained. Based on the size-controlled fabrication method, SC-coated zein nanoparticles could also be obtained in a size-controlled manner by incubation of the coating material with the already-formed zein particles. The resultant nanoparticles showed better performance in both drug loading and controlled release, compared with zein/SC hybrid nanoparticles fabricated by adding aqueous ethanol solution to SC solution. The possible mechanisms of the nanoprecipitation process and self-assembly formation of these nanoparticles are discussed. PMID:29184408

Size-controlled fabrication of zein nano/microparticles by modified anti-solvent precipitation with/without sodium caseinate.

PubMed

Li, Feng; Chen, Yan; Liu, Shubo; Qi, Jian; Wang, Weiying; Wang, Chenhua; Zhong, Ruiyue; Chen, Zhijun; Li, Xiaoming; Guan, Yuanzhou; Kong, Wei; Zhang, Yong

2017-01-01

Zein-based nano/microparticles have been demonstrated to be promising carrier systems for both the food industry and biomedical applications. However, the fabrication of size-controlled zein particles has been a challenging issue. In this study, a modified anti-solvent precipitation method was developed, and the effects of various factors, such as mixing method, solvent/anti-solvent ratio, temperature, zein concentrations and the presence of sodium caseinate (SC) on properties of zein particles were investigated. Evidence is presented that, among the previously mentioned factors, the mixing method, especially mixing rate, could be used as an effective parameter to control the size of zein particles without changing other parameters. Moreover, through fine-tuning the mixing rate together with zein concentration, particles with sizes ranging from nanometers to micrometers and low polydispersity index values could be easily obtained. Based on the size-controlled fabrication method, SC-coated zein nanoparticles could also be obtained in a size-controlled manner by incubation of the coating material with the already-formed zein particles. The resultant nanoparticles showed better performance in both drug loading and controlled release, compared with zein/SC hybrid nanoparticles fabricated by adding aqueous ethanol solution to SC solution. The possible mechanisms of the nanoprecipitation process and self-assembly formation of these nanoparticles are discussed.

Lagrangian pathways of upwelling in the Southern Ocean

NASA Astrophysics Data System (ADS)

Viglione, Giuliana A.; Thompson, Andrew F.

2016-08-01

The spatial and temporal variability of upwelling into the mixed layer in the Southern Ocean is studied using a 1/10° ocean general circulation model. Virtual drifters are released in a regularly spaced pattern across the Southern Ocean at depths of 250, 500, and 1000 m during both summer and winter months. The drifters are advected along isopycnals for a period of 4 years, unless they outcrop into the mixed layer, where lateral advection and a parameterization of vertical mixing are applied. The focus of this study is on the discrete exchange between the model mixed layer and the interior. Localization of interior-mixed layer exchange occurs downstream of major topographic features across the Indian and Pacific basins, creating "hotspots" of outcropping. Minimal outcropping occurs in the Atlantic basin, while 59% of drifters outcrop in the Pacific sector and in Drake Passage (the region from 140° W to 40° W), a disproportionately large amount even when considering the relative basin sizes. Due to spatial and temporal variations in mixed layer depth, the Lagrangian trajectories provide a statistical measure of mixed layer residence times. For each exchange into the mixed layer, the residence time has a Rayleigh distribution with a mean of 30 days; the cumulative residence time of the drifters is 261 ± 194 days, over a period of 4 years. These results suggest that certain oceanic gas concentrations, such as CO2 and 14C, will likely not reach equilibrium with the atmosphere before being resubducted.

INTERDISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Polar Mixing Optical Phonon Spectra in Wurtzite GaN Cylindrical Quantum Dots: Quantum Size and Dielectric Effects

NASA Astrophysics Data System (ADS)

Zhang, Li; Liao, Jian-Shang

2010-05-01

The interface-optical-propagating (IO-PR) mixing phonon modes of a quasi-zero-dimensional (QoD) wurtzite cylindrical quantum dot (QD) structure are derived and studied by employing the macroscopic dielectric continuum model. The analytical phonon states of IO-PR mixing modes are given. It is found that there are two types of IO-PR mixing phonon modes, i.e. ρ-IO/z-PR mixing modes and the z-IO/ρ-PR mixing modes existing in QoD wurtzite QDs. And each IO-PR mixing modes also have symmetrical and antisymmetrical forms. Via a standard procedure of field quantization, the Fröhlich Hamiltonians of electron-(IO-PR) mixing phonons interaction are obtained. Numerical calculations on a wurtzite GaN cylindrical QD are performed. The results reveal that both the radial-direction size and the axial-direction size as well as the dielectric matrix have great influence on the dispersive frequencies of the IO-PR mixing phonon modes. The limiting features of dispersive curves of these phonon modes are discussed in depth. The phonon modes “reducing" behavior of wurtzite quantum confined systems has been observed obviously in the structures. Moreover, the degenerating behaviors of the IO-PR mixing phonon modes in wurtzite QoD QDs to the IO modes and PR modes in wurtzite Q2D QW and Q1D QWR systems are analyzed deeply from both of the viewpoints of physics and mathematics.

Women and Men Together in Recruit Training.

PubMed

Orme, Geoffrey J; Kehoe, E James

2018-05-01

Although men and women recruits to the Australian Army have trained in mixed-gender platoons since 1995, restrictions on women joining the combat arms were only removed in 2016. As part of a longitudinal study starting with recruit training, this article examined recruit records collected before 2016 with the aims of delineating (1) the relative performance of women versus men in mixed-gender platoons and (2) the relative performance of men in mixed-gender platoons versus all-male platoons. De-identified instructor ratings for 630 females and 4,505 males who completed training between 2011 and 2015 were obtained. Recruits were distributed across 128 platoons (averaging 41.6 members, SD = 8.3) of which 75% contained females, in proportions from 5% to 45%. These analyses were conducted under defense ethics approval DPR-LREP 069-15. Factor analyses revealed that instructor ratings generally loaded onto a single factor, accounting 77.2% of the variance. Consequently, a composite recruit performance score (range 1-5) was computed for 16 of 19 competencies. Analyses of the scores revealed that the distributions of the scores for females and males overlapped considerably. Observed effects were negligible to small in size. The distributions were all centered between 3.0 and 3.5. In mixed-gender platoons, 51% of the females and 52% of the males fell in this band, and 44% of recruits in all-male platoons had scores in this band. The lower three bands (1.0-3.0) contained a slightly greater proportion of females (18%) than males in either mixed-gender platoons (12%) or all-male platoons (12%). Conversely, the upper three bands (3.5-5.0) contained a slightly smaller percentage of females (31%) than males in either mixed-gender platoons (36%) or all-male platoons (44%). Although scores for females were reliably lower than those of males in mixed-gender platoons, χ2 (4) = 16.01, p < 0.01, the effect size (V = 0.07) did not reach the criterion for even a small effect (0.10). For male recruits, those in mixed-gender platoons had scores that were reliably lower than in all-male platoons, χ2 (4) = 48.38, p < 0.001; its effect size (V = 0.11) just exceeded the criterion for a small effect (0.10). Further analyses revealed that male scores had a near-zero correlation (r = -0.033) with the proportion of females in platoons (0-45%). This large-scale secondary analysis of instructor ratings of female and male recruits provides a platform for monitoring the integration of women into the combat arms. The analyses revealed nearly complete overlap in the performance of female versus male recruits. The detected gender-related differences were negligible to small in size. These small differences must be viewed with considerable caution. They may be artifacts of rater bias or other uncontrolled features of the rating system, which was designed for reporting individual recruit performance rather than aggregate analyses. Even with these limitations, this baseline snapshot of recruit performance suggests that, at recruit training, women and men are already working well together, which bodes well for their subsequent integration into the combat arms.

Factors affecting computer mouse use for young children: implications for AAC.

PubMed

Costigan, F Aileen; Light, Janice C; Newell, Karl M

2012-06-01

More than 12% of preschoolers receiving special education services have complex communication needs, including increasing numbers of children who do not have significant motor impairments (e.g., children with autism spectrum disorders, Down syndrome, etc.). In order to meet their diverse communication needs (e.g., face-to-face, written, Internet, telecommunication), these children may use mainstream technologies accessed via the mouse, yet little is known about factors that affect the mouse performance of young children. This study used a mixed factorial design to investigate the effects of age, target size, and angle of approach on accuracy and time required for accurate target selection with a mouse for 20 3-year-old and 20 4-year-old children. The 4-year-olds were generally more accurate and faster than the 3-year-olds. Target size and angle mediated differences in performance within age groups. The 3-year-olds were more accurate and faster in selecting the medium and large targets relative to the small target, were faster in selecting the large relative to the medium target, and were faster in selecting targets along the vertical relative to the diagonal angle. The 4-year-olds were faster in selecting the medium and large targets relative to the small target. Implications for improving access to AAC include the preliminary suggestion of age-related threshold target sizes that support sufficient accuracy, the possibility of efficiency benefits when target size is increased up to an age-related threshold, and identification of the potential utility of the vertical angle as a context for training navigational input device use.

Use of different rapid mixing devices for controlling the properties of magnetite nanoparticles produced by precipitation

NASA Astrophysics Data System (ADS)

Wei, Li; Hervé, Muhr; Edouard, Plasari

2012-03-01

Magnetite nanoparticles were precipitated by the classic Massart's method in a 2.5 L stirred tank reactor where the injection of reagent solutions was effectuated by different micro-mixers (T-tube and Hartridge-Roughton rapid mixing devices). The specific surface area, the average particle size and the particle size distribution were highly influenced by changing operating parameters. Laser Diffraction, BET adsorption, Energy-Dispersive X-ray Spectroscopy (EDX), Raman spectroscopy and Transmission Electron Microscopy (TEM) were used for characterizing magnetite nanoparticles. Especially, Hartridge-Roughton micromixer appears to be the most efficient mixing device for producing magnetite nanoparticles. The average particle size of magnetite nanoparticles prepared by Hartridge-Roughton rapid mixing device was less than 10 nm and the EDX and Raman spectroscopy shows that the particle purity is quite high.

The formation of peak rings in large impact craters.

PubMed

Morgan, Joanna V; Gulick, Sean P S; Bralower, Timothy; Chenot, Elise; Christeson, Gail; Claeys, Philippe; Cockell, Charles; Collins, Gareth S; Coolen, Marco J L; Ferrière, Ludovic; Gebhardt, Catalina; Goto, Kazuhisa; Jones, Heather; Kring, David A; Le Ber, Erwan; Lofi, Johanna; Long, Xiao; Lowery, Christopher; Mellett, Claire; Ocampo-Torres, Rubén; Osinski, Gordon R; Perez-Cruz, Ligia; Pickersgill, Annemarie; Poelchau, Michael; Rae, Auriol; Rasmussen, Cornelia; Rebolledo-Vieyra, Mario; Riller, Ulrich; Sato, Honami; Schmitt, Douglas R; Smit, Jan; Tikoo, Sonia; Tomioka, Naotaka; Urrutia-Fucugauchi, Jaime; Whalen, Michael; Wittmann, Axel; Yamaguchi, Kosei E; Zylberman, William

2016-11-18

Large impacts provide a mechanism for resurfacing planets through mixing near-surface rocks with deeper material. Central peaks are formed from the dynamic uplift of rocks during crater formation. As crater size increases, central peaks transition to peak rings. Without samples, debate surrounds the mechanics of peak-ring formation and their depth of origin. Chicxulub is the only known impact structure on Earth with an unequivocal peak ring, but it is buried and only accessible through drilling. Expedition 364 sampled the Chicxulub peak ring, which we found was formed from uplifted, fractured, shocked, felsic basement rocks. The peak-ring rocks are cross-cut by dikes and shear zones and have an unusually low density and seismic velocity. Large impacts therefore generate vertical fluxes and increase porosity in planetary crust. Copyright © 2016, American Association for the Advancement of Science.

Model studies of the beam-filling error for rain-rate retrieval with microwave radiometers

NASA Technical Reports Server (NTRS)

Ha, Eunho; North, Gerald R.

1995-01-01

Low-frequency (less than 20 GHz) single-channel microwave retrievals of rain rate encounter the problem of beam-filling error. This error stems from the fact that the relationship between microwave brightness temperature and rain rate is nonlinear, coupled with the fact that the field of view is large or comparable to important scales of variability of the rain field. This means that one may not simply insert the area average of the brightness temperature into the formula for rain rate without incurring both bias and random error. The statistical heterogeneity of the rain-rate field in the footprint of the instrument is key to determining the nature of these errors. This paper makes use of a series of random rain-rate fields to study the size of the bias and random error associated with beam filling. A number of examples are analyzed in detail: the binomially distributed field, the gamma, the Gaussian, the mixed gamma, the lognormal, and the mixed lognormal ('mixed' here means there is a finite probability of no rain rate at a point of space-time). Of particular interest are the applicability of a simple error formula due to Chiu and collaborators and a formula that might hold in the large field of view limit. It is found that the simple formula holds for Gaussian rain-rate fields but begins to fail for highly skewed fields such as the mixed lognormal. While not conclusively demonstrated here, it is suggested that the notionof climatologically adjusting the retrievals to remove the beam-filling bias is a reasonable proposition.

Nanopatterns by phase separation of patterned mixed polymer monolayers

DOEpatents

Huber, Dale L; Frischknecht, Amalie

2014-02-18

Micron-size and sub-micron-size patterns on a substrate can direct the self-assembly of surface-bonded mixed polymer brushes to create nanoscale patterns in the phase-separated mixed polymer brush. The larger scale features, or patterns, can be defined by a variety of lithographic techniques, as well as other physical and chemical processes including but not limited to etching, grinding, and polishing. The polymer brushes preferably comprise vinyl polymers, such as polystyrene and poly(methyl methacrylate).

Strengthening and Strength Uniformity of Structural Ceramics

DTIC Science & Technology

1984-04-01

Center. Thousand Oaks, California 91360 APPENDIX III Alumina and M230,/ZrO2 (I to 10 vo1%) composite powders 1. Introductioni were mixed and conslidated...distribution for the A1O 3 . Different mixing the flocced slurries with deionized water, followed by magnifications were used for bimodal microstructures...2 with HCi, size of the A120 (A) and ZRO: (Z), mean size ratio of the two mixing together with ultrasonic treatment, and again floccing at phases

Aggregation of grains in a turbulent pre-solar disk. [meteoritic inclusion and chondrule subcentimeter maximum size argument

NASA Technical Reports Server (NTRS)

Wieneke, B.; Clayton, D. D.

1983-01-01

The growth and evolution of grains in the protostellar nebula are investigated within the context of turbulent low-mass disk models developed by previous investigators. Because of grain collisions promoted by the turbulent velocities, particles aggregate to millimeter size in times of the order of 1000 yrs. During the growth the particles acquire a large inward radial velocity due to gas drag (Weidenschilling, 1977) and spiral into the sun. The calculations indicate that the final size of the particles does not exceed a few centimeters. This result is not very sensitive to the specific nebula parameters. For all conditions investigated it seems impossible to grow meter- or kilometer-sized bodies that could decouple from the gas motion. An additional argument is given that shows that only particles smaller than centimeter size can survive drift into the growing sun by being transported radially outward by turbulent mixing. This agrees well with the maximum size of inclusions and chondrules. Since sedimentation of grains and subsequent dust disk instability is effectively inhibited by turbulent stirring, the formation of planetesimals and planets cannot be explained in the above scenario without further assumptions.

Population size vs. social connectedness - A gene-culture coevolutionary approach to cumulative cultural evolution.

PubMed

Kobayashi, Yutaka; Ohtsuki, Hisashi; Wakano, Joe Y

2016-10-01

It has long been debated if population size is a crucial determinant of the level of culture. While empirical results are mixed, recent theoretical studies suggest that social connectedness between people may be a more important factor than the size of the entire population. These models, however, do not take into account evolutionary responses of learning strategies determining the mode of transmission and innovation and are hence not suitable for predicting the long-term implications of parameters of interest. In the present paper, to address this issue, we provide a gene-culture coevolution model, in which the microscopic learning process of each individual is explicitly described as a continuous-time stochastic process and time allocation to social and individual learning is allowed to evolve. We have found that social connectedness has a larger impact on the equilibrium level of culture than population size especially when connectedness is weak and population size is large. This result, combined with those of previous culture-only models, points to the importance of studying separate effects of population size and internal social structure to better understand spatiotemporal variation in the level of culture. Copyright © 2016 Elsevier Inc. All rights reserved.

A global modeling study on carbonaceous aerosol microphysical characteristics and radiative forcing

NASA Astrophysics Data System (ADS)

Bauer, S. E.; Menon, S.; Koch, D.; Bond, T. C.; Tsigaridis, K.

2010-02-01

Recently, attention has been drawn towards black carbon aerosols as a short-term climate warming mitigation candidate. However the global and regional impacts of the direct, cloud-indirect and semi-direct forcing effects are highly uncertain, due to the complex nature of aerosol evolution and the way that mixed, aged aerosols interact with clouds and radiation. A detailed aerosol microphysical scheme, MATRIX, embedded within the GISS climate model is used in this study to present a quantitative assessment of the impact of microphysical processes involving black carbon, such as emission size distributions and optical properties on aerosol cloud activation and radiative forcing. Our best estimate for net direct and indirect aerosol radiative forcing between 1750 and 2000 is -0.56 W/m2. However, the direct and indirect aerosol effects are quite sensitive to the black and organic carbon size distribution and consequential mixing state. The net radiative forcing can vary between -0.32 to -0.75 W/m2 depending on these carbonaceous particle properties at emission. Assuming that sulfates, nitrates and secondary organics form a coating around a black carbon core, rather than forming a uniformly mixed particle, changes the overall net aerosol radiative forcing from negative to positive. Taking into account internally mixed black carbon particles let us simulate correct aerosol absorption. Black carbon absorption is amplified by sulfate and nitrate coatings, but even more strongly by organic coatings. Black carbon mitigation scenarios generally showed reduced radiative forcing when sources with a large proportion of black carbon, such as diesel, are reduced; however reducing sources with a larger organic carbon component as well, such as bio-fuels, does not necessarily lead to climate benefits.

A Typology of Mixed Methods Sampling Designs in Social Science Research

ERIC Educational Resources Information Center

Onwuegbuzie, Anthony J.; Collins, Kathleen M. T.

2007-01-01

This paper provides a framework for developing sampling designs in mixed methods research. First, we present sampling schemes that have been associated with quantitative and qualitative research. Second, we discuss sample size considerations and provide sample size recommendations for each of the major research designs for quantitative and…

[Primary branch size of Pinus koraiensis plantation: a prediction based on linear mixed effect model].

PubMed

Dong, Ling-Bo; Liu, Zhao-Gang; Li, Feng-Ri; Jiang, Li-Chun

2013-09-01

By using the branch analysis data of 955 standard branches from 60 sampled trees in 12 sampling plots of Pinus koraiensis plantation in Mengjiagang Forest Farm in Heilongjiang Province of Northeast China, and based on the linear mixed-effect model theory and methods, the models for predicting branch variables, including primary branch diameter, length, and angle, were developed. Considering tree effect, the MIXED module of SAS software was used to fit the prediction models. The results indicated that the fitting precision of the models could be improved by choosing appropriate random-effect parameters and variance-covariance structure. Then, the correlation structures including complex symmetry structure (CS), first-order autoregressive structure [AR(1)], and first-order autoregressive and moving average structure [ARMA(1,1)] were added to the optimal branch size mixed-effect model. The AR(1) improved the fitting precision of branch diameter and length mixed-effect model significantly, but all the three structures didn't improve the precision of branch angle mixed-effect model. In order to describe the heteroscedasticity during building mixed-effect model, the CF1 and CF2 functions were added to the branch mixed-effect model. CF1 function improved the fitting effect of branch angle mixed model significantly, whereas CF2 function improved the fitting effect of branch diameter and length mixed model significantly. Model validation confirmed that the mixed-effect model could improve the precision of prediction, as compare to the traditional regression model for the branch size prediction of Pinus koraiensis plantation.

Effects of shallow natural gas well structures and associated roads on grassland songbird reproductive success in Alberta, Canada

PubMed Central

Koper, Nicola

2017-01-01

Grassland songbird populations across North America have experienced dramatic population declines due to habitat loss and degradation. In Canada, energy development continues to fragment and disturb prairie habitat, but effects of oil and gas development on reproductive success of songbirds in North American mixed-grass prairies remains largely unknown. From 2010–2012, in southeastern Alberta, Canada, we monitored 257 nests of two ground-nesting grassland songbird species, Savannah sparrow (Passerculus sandwichensis) and chestnut-collared longspur (Calcarius ornatus). Nest locations varied with proximity to and density of conventional shallow gas well structures and associated roads in forty-two 258-ha mixed-grass prairie sites. We estimated the probabilities of nest success and clutch size relative to gas well structures and roads. There was little effect of distance to or density of gas well structure on nest success; however, Savannah sparrow experienced lower nest success near roads. Clutch sizes were lower near gas well structures and cattle water sources. Minimizing habitat disturbance surrounding gas well structures, and reducing abundance of roads and trails, would help minimize impacts on reproductive success for some grassland songbirds. PMID:28355241

Computational studies of the glass-forming ability of model bulk metallic glasses

NASA Astrophysics Data System (ADS)

Zhang, Kai; Wang, Minglei; Papanikolaou, Stefanos; Liu, Yanhui; Schroers, Jan; Shattuck, Mark D.; O'Hern, Corey S.

2013-09-01

Bulk metallic glasses (BMGs) are produced by rapidly thermally quenching supercooled liquid metal alloys below the glass transition temperature at rates much faster than the critical cooling rate Rc below which crystallization occurs. The glass-forming ability of BMGs increases with decreasing Rc, and thus good glass-formers possess small values of Rc. We perform molecular dynamics simulations of binary Lennard-Jones (LJ) mixtures to quantify how key parameters, such as the stoichiometry, particle size difference, attraction strength, and heat of mixing, influence the glass-formability of model BMGs. For binary LJ mixtures, we find that the best glass-forming mixtures possess atomic size ratios (small to large) less than 0.92 and stoichiometries near 50:50 by number. In addition, weaker attractive interactions between the smaller atoms facilitate glass formation, whereas negative heats of mixing (in the experimentally relevant regime) do not change Rc significantly. These results are tempered by the fact that the slowest cooling rates achieved in our simulations correspond to ˜1011 K/s, which is several orders of magnitude higher than Rc for typical BMGs. Despite this, our studies represent a first step in the development of computational methods for quantitatively predicting glass-formability.

Theoretical and Experimental Investigations of the Process of Vibration Treatment of Liquid Metals Containing Nanoparticles

NASA Astrophysics Data System (ADS)

Vorozhtsov, S.; Kudryashova, O.; Promakhov, V.; Dammer, V.; Vorozhtsov, A.

2016-12-01

It is known that the use of external effects, such as acoustic fields (from ultrasonic to low-frequency range), help in breaking down agglomerates, improving particle wettability, providing uniform particle distribution in the melt volume, and reducing the grain size. The fragmentation of growing crystals, de-agglomeration of particles and their mixing in liquid metal under the influence of vibration (with frequencies of 10-100 Hz) are considered in this paper. The major advantage of such a technique in comparison with high-frequency methods (sonic, ultrasonic) is the capability of processing large melt volumes proportional to the wavelength. The mechanisms of the breaking down of particle agglomerates and the mixing of particles under conditions of cavitation and turbulence during the vibration treatment of the melt are considered. Expressions linking the threshold intensity and frequency with the amplitude necessary to activate mechanisms of turbulence and cavitation were obtained. The results of vibration treatment experiments for an aluminum alloy containing diamond nanoparticles are given. This treatment makes it possible to significantly reduce the grain size and to improve the casting homogeneity and thus improve the mechanical properties of the alloy.

Some problems associated with the analysis and interpretation of mixed carbonate and quartz beach sands, illustrated by examples from North-West Ireland

NASA Astrophysics Data System (ADS)

Carter, R. W. G.

1982-09-01

Mixes of carbonate and quartz sands, which are commonly encountered in Recent coastal sediments, require careful analysis if they are to be correctly interpreted. Grain-size data fall into multimodal or segmented zig-zag distributions which may require some kind of component separation if they are to be summarised by conventional statistics, and before they can be assigned to a particular hydrodynamic depositional process or environment. Unfortunately, separation techniques are only spasmodically applied, usually without due regard to the consequences. Such artificially filtered or truncated distributions are of little subsequent use. Using a range of samples from two beaches in NW Ireland, where carbonate proportions range from nearly zero to over sixty percent, the interrelationships of the two dominant components were examined. Where only a small carbonate proportion is incorporated into a large quartz one, predictable modifications of the size-curve are apparent. However, the components are more independent if mixtures are near equal. The occurrence of a number of distinctive combinations of simple straight lines and complex zig-zag curves probably reflects the relatively dynamic nature of the carbonate fraction.

Effects of shallow natural gas well structures and associated roads on grassland songbird reproductive success in Alberta, Canada.

PubMed

Yoo, Jenny; Koper, Nicola

2017-01-01

Grassland songbird populations across North America have experienced dramatic population declines due to habitat loss and degradation. In Canada, energy development continues to fragment and disturb prairie habitat, but effects of oil and gas development on reproductive success of songbirds in North American mixed-grass prairies remains largely unknown. From 2010-2012, in southeastern Alberta, Canada, we monitored 257 nests of two ground-nesting grassland songbird species, Savannah sparrow (Passerculus sandwichensis) and chestnut-collared longspur (Calcarius ornatus). Nest locations varied with proximity to and density of conventional shallow gas well structures and associated roads in forty-two 258-ha mixed-grass prairie sites. We estimated the probabilities of nest success and clutch size relative to gas well structures and roads. There was little effect of distance to or density of gas well structure on nest success; however, Savannah sparrow experienced lower nest success near roads. Clutch sizes were lower near gas well structures and cattle water sources. Minimizing habitat disturbance surrounding gas well structures, and reducing abundance of roads and trails, would help minimize impacts on reproductive success for some grassland songbirds.

Electron transfer between colloidal ZnO nanocrystals.

PubMed

Hayoun, Rebecca; Whitaker, Kelly M; Gamelin, Daniel R; Mayer, James M

2011-03-30

Colloidal ZnO nanocrystals capped with dodecylamine and dissolved in toluene can be charged photochemically to give stable solutions in which electrons are present in the conduction bands of the nanocrystals. These conduction-band electrons are readily monitored by EPR spectroscopy, with g* values that correlate with the nanocrystal sizes. Mixing a solution of charged small nanocrystals (e(-)(CB):ZnO-S) with a solution of uncharged large nanocrystals (ZnO-L) caused changes in the EPR spectrum indicative of quantitative electron transfer from small to large nanocrystals. EPR spectra of the reverse reaction, e(-)(CB):ZnO-L + ZnO-S, showed that electrons do not transfer from large to small nanocrystals. Stopped-flow kinetics studies monitoring the change in the UV band-edge absorption showed that reactions of 50 μM nanocrystals were complete within the 5 ms mixing time of the instrument. Similar results were obtained for the reaction of charged nanocrystals with methyl viologen (MV(2+)). These and related results indicate that the electron-transfer reactions of these colloidal nanocrystals are quantitative and very rapid, despite the presence of ~1.5 nm long dodecylamine capping ligands. These soluble ZnO nanocrystals are thus well-defined redox reagents suitable for studies of electron transfer involving semiconductor nanostructures.

Derivation of Cloud Heating Rate Profiles using observations of Mixed-Phase Arctic Clouds: Impacts of Solar Zenith Angle

NASA Astrophysics Data System (ADS)

Zhang, G.; McFarquhar, G.; Poellot, M.; Verlinde, J.; Heymsfield, A.; Kok, G.

2005-12-01

Arctic stratus clouds play an important role in the energy balance of the Arctic region. Previous studies have suggested that Arctic stratus persist due to a balance among cloud top radiation cooling, latent heating, ice crystal fall out and large scale forcing. In this study, radiative heating profiles through Arctic stratus are computed using cloud, surface and thermodynamic observations obtained during the Mixed-Phase Arctic Cloud Experiment (M-PACE) as input to the radiative transfer model STREAMER. In particular, microphysical and macrophycial cloud properties such as phase, water content, effective particle size, particle shape, cloud height and cloud thickness were derived using data collected by in-situ sensors on the University of North Dakota (UND) Citation and ground-based remote sensors at Barrow and Oliktok Point. Temperature profiles were derived from radiosonde launches and a fresh snow surface was assumed. One series of sensitivity studies explored the dependence of the heating profile on the solar zenith angle. For smaller solar zenith angles, more incoming solar radiation is received at cloud top acting to counterbalance infrared cooling. As solar zenith angle in the Arctic is large compared to low latitudes, a large solar zenith angle may contribute to the longevity of these clouds.

Mixing device for materials with large density differences

DOEpatents

Gregg, David W.

1994-01-01

An auger-tube pump mixing device for mixing materials with large density differences while maintaining low stirring RPM and low power consumption. The mixing device minimizes the formation of vortexes and minimizes the incorporation of small bubbles in the liquid during mixing. By avoiding the creation of a vortex the device provides efficient stirring of full containers without spillage over the edge. Also, the device solves the problem of effective mixing in vessels where the liquid height is large compared to the diameter. Because of the gentle stirring or mixing by the device, it has application for biomedical uses where cell damage is to be avoided.

Mixing device for materials with large density differences

DOEpatents

Gregg, D.W.

1994-08-16

An auger-tube pump mixing device is disclosed for mixing materials with large density differences while maintaining low stirring RPM and low power consumption. The mixing device minimizes the formation of vortexes and minimizes the incorporation of small bubbles in the liquid during mixing. By avoiding the creation of a vortex the device provides efficient stirring of full containers without spillage over the edge. Also, the device solves the problem of effective mixing in vessels where the liquid height is large compared to the diameter. Because of the gentle stirring or mixing by the device, it has application for biomedical uses where cell damage is to be avoided. 2 figs.

Nonadiabatic effects in ultracold molecules via anomalous linear and quadratic Zeeman shifts.

PubMed

McGuyer, B H; Osborn, C B; McDonald, M; Reinaudi, G; Skomorowski, W; Moszynski, R; Zelevinsky, T

2013-12-13

Anomalously large linear and quadratic Zeeman shifts are measured for weakly bound ultracold 88Sr2 molecules near the intercombination-line asymptote. Nonadiabatic Coriolis coupling and the nature of long-range molecular potentials explain how this effect arises and scales roughly cubically with the size of the molecule. The linear shifts yield nonadiabatic mixing angles of the molecular states. The quadratic shifts are sensitive to nearby opposite f-parity states and exhibit fourth-order corrections, providing a stringent test of a state-of-the-art ab initio model.

Preparation of AgInSe2 thin films grown by vacuum evaporation method

NASA Astrophysics Data System (ADS)

Matsuo, H.; Yoshino, K.; Ikari, T.

2006-09-01

Polycrystalline AgInSe2 thin films were successfully grown on glass substrates by an evaporation method. The starting materials were stoichiometrically mixed Ag2Se and In2Se3 powders. X-ray diffraction revealed that the sample annealed at 600 °C consisted of AgInSe2 single phase, with (112) orientation and a large grain size. The lattice constant (a axis) was close to JCPDS values. From optical transmittance and reflectance measurements, the bandgap energy was estimated to be 1.17 eV.

Bile Salt Micelles and Phospholipid Vesicles Present in Simulated and Human Intestinal Fluids: Structural Analysis by Flow Field-Flow Fractionation/Multiangle Laser Light Scattering.

PubMed

Elvang, Philipp A; Hinna, Askell H; Brouwers, Joachim; Hens, Bart; Augustijns, Patrick; Brandl, Martin

2016-09-01

Knowledge about colloidal assemblies present in human intestinal fluids (HIFs), such as bile salt micelles and phospholipid vesicles, is regarded of importance for a better understanding of the in vivo dissolution and absorption behavior of poorly soluble drugs (Biopharmaceutics Classification System class II/IV drugs) because of their drug-solubilizing ability. The characterization of these potential drug-solubilizing compartments is a prerequisite for further studies of the mechanistic interplays between drug molecules and colloidal structures within HIFs. The aim of the present study was to apply asymmetrical flow field-flow fractionation (AF4) in combination with multiangle laser light scattering in an attempt to reveal coexistence of colloidal particles in both artificial and aspirated HIFs and to determine their sizes. Asymmetrical flow field-flow fractionation/multiangle laser light scattering analysis of the colloidal phase of intestinal fluids allowed for a detailed insight into the whole spectrum of submicron- to micrometer-sized particles. With respect to the simulated intestinal fluids mimicking fasted and fed state (FaSSIF-V1 and FeSSIF-V1, respectively), FaSSIF contained one distinct size fraction of colloidal assemblies, whereas FeSSIF contained 2 fractions of colloidal species with significantly different sizes. These size fractions likely represent (1) mixed taurocholate-phospholipid-micelles, as indicated by a size range up to 70 nm (in diameter) and a strong UV absorption and (2) small phospholipid vesicles of 90-210 nm diameter. In contrast, within the colloidal phase of the fasted state aspirate of a human volunteer, 4 different size fractions were separated from each other in a consistent and reproducible manner. The 2 fractions containing large particles showed mean sizes of approximately 50 and 200 nm, respectively (intensity-weighted mean diameter, Dz), likely representing mixed cholate/phospholipid micelles and phospholipid vesicles, respectively. The sizes of the smaller 2 fractions being below the size range of multiangle laser light scattering analysis (<20 nm) and their strong UV absorption indicates that they represent either pure cholate micelles or small mixed micelles. Within the colloidal fraction of the fed-state human aspirate, similar colloidal assemblies were detected as in the fasted state human aspirates. The observed differences between SIF and HIF indicate that the simulated intestinal fluids (FaSSIF-V1 and FeSSIF-V1) represent rather simplified models of the real human intestinal environment in terms of coexisting colloidal particles. It is hypothesized that the different supramolecular assemblies detected differ in their lipid composition, which may affect their affinity toward drug compounds and thus the drug-solubilizing capabilities. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Effects of turbulence on mixed-phase deep convective clouds under different basic-state winds and aerosol concentrations

NASA Astrophysics Data System (ADS)

Lee, Hyunho; Baik, Jong-Jin; Han, Ji-Young

2014-12-01

The effects of turbulence-induced collision enhancement (TICE) on mixed-phase deep convective clouds are numerically investigated using a 2-D cloud model with bin microphysics for uniform and sheared basic-state wind profiles and different aerosol concentrations. Graupel particles account for the most of the cloud mass in all simulation cases. In the uniform basic-state wind cases, graupel particles with moderate sizes account for some of the total graupel mass in the cases with TICE, whereas graupel particles with large sizes account for almost all the total graupel mass in the cases without TICE. This is because the growth of ice crystals into small graupel particles is enhanced due to TICE. The changes in the size distributions of graupel particles due to TICE result in a decrease in the mass-averaged mean terminal velocity of graupel particles. Therefore, the downward flux of graupel mass, and thus the melting of graupel particles, is reduced due to TICE, leading to a decrease in the amount of surface precipitation. Moreover, under the low aerosol concentration, TICE increases the sublimation of ice particles, consequently playing a partial role in reducing the amount of surface precipitation. The effects of TICE are less pronounced in the sheared basic-state wind cases than in the uniform basic-state wind cases because the number of ice crystals is much smaller in the sheared basic-state wind cases than in the uniform basic-state wind cases. Thus, the size distributions of graupel particles in the cases with and without TICE show little difference.

Ice residual properties in mixed-phase clouds at the high-alpine Jungfraujoch site.

PubMed

Kupiszewski, Piotr; Zanatta, Marco; Mertes, Stephan; Vochezer, Paul; Lloyd, Gary; Schneider, Johannes; Schenk, Ludwig; Schnaiter, Martin; Baltensperger, Urs; Weingartner, Ernest; Gysel, Martin

2016-10-27

Ice residual (IR) and total aerosol properties were measured in mixed-phase clouds (MPCs) at the high-alpine Jungfraujoch research station. Black carbon (BC) content and coating thickness of BC-containing particles were determined using single-particle soot photometers. The ice activated fraction (IAF), derived from a comparison of IR and total aerosol particle size distributions, showed an enrichment of large particles in the IR, with an increase in the IAF from values on the order of 10 -4 to 10 -3 for 100 nm (diameter) particles to 0.2 to 0.3 for 1 μm (diameter) particles. Nonetheless, due to the high number fraction of submicrometer particles with respect to total particle number, IR size distributions were still dominated by the submicrometer aerosol. A comparison of simultaneously measured number size distributions of BC-free and BC-containing IR and total aerosol particles showed depletion of BC by number in the IR, suggesting that BC does not play a significant role in ice nucleation in MPCs at the Jungfraujoch. The potential anthropogenic climate impact of BC via the glaciation effect in MPCs is therefore likely to be negligible at this site and in environments with similar meteorological conditions and a similar aerosol population. The IAF of the BC-containing particles also increased with total particle size, in a similar manner as for the BC-free particles, but on a level 1 order of magnitude lower. Furthermore, BC-containing IR were found to have a thicker coating than the BC-containing total aerosol, suggesting the importance of atmospheric aging for ice nucleation.

Droplet and multiphase effects in a shock-driven hydrodynamic instability with reshock

NASA Astrophysics Data System (ADS)

Middlebrooks, John B.; Avgoustopoulos, Constantine G.; Black, Wolfgang J.; Allen, Roy C.; McFarland, Jacob A.

2018-06-01

Shock-driven multiphase instabilities (SDMI) are unique physical phenomena that have far-reaching applications in engineering and science such as high energy explosions, scramjet combustors, and supernovae events. The SDMI arises when a multiphase field is impulsively accelerated by a shock wave and evolves as a result of gradients in particle-gas momentum transfer. A new shock tube facility has been constructed to study the SDMI. Experiments were conducted to investigate liquid particle and multiphase effects in the SDMI. A multiphase cylindrical interface was created with water droplet laden air in our horizontal shock tube facility. The interface was accelerated by a Mach 1.66 shock wave, and its reflection from the end wall. The interface development was captured using laser illumination and a high-resolution CCD camera. Laser interferometry was used to determine the droplet size distribution. A particle filtration technique was used to determine mass loading within an interface and verify particle size distribution. The effects of particle number density, particle size, and a secondary acceleration (reshock) of the interface were noted. Particle number density effects were found comparable to Atwood number effects in the Richtmyer-Meshkov instability for small (˜ 1.7 {μ }m) droplets. Evaporation was observed to alter droplet sizes and number density, markedly after reshock. For large diameter droplets (˜ 10.7 {μ }m), diminished development was observed with larger droplets lagging far behind the interface. These lagging droplets were also observed to breakup after reshock into structured clusters of smaller droplets. Mixing width values were reported to quantify mixing effects seen in images.

Cloud-edge mixing: Direct numerical simulation and observations in Indian Monsoon clouds

NASA Astrophysics Data System (ADS)

Kumar, Bipin; Bera, Sudarsan; Prabha, Thara V.; Grabowski, Wojceich W.

2017-03-01

A direct numerical simulation (DNS) with the decaying turbulence setup has been carried out to study cloud-edge mixing and its impact on the droplet size distribution (DSD) applying thermodynamic conditions observed in monsoon convective clouds over Indian subcontinent during the Cloud Aerosol Interaction and Precipitation Enhancement EXperiment (CAIPEEX). Evaporation at the cloud-edges initiates mixing at small scale and gradually introduces larger-scale fluctuations of the temperature, moisture, and vertical velocity due to droplet evaporation. Our focus is on early evolution of simulated fields that show intriguing similarities to the CAIPEEX cloud observations. A strong dilution at the cloud edge, accompanied by significant spatial variations of the droplet concentration, mean radius, and spectral width, are found in both the DNS and in observations. In DNS, fluctuations of the mean radius and spectral width come from the impact of small-scale turbulence on the motion and evaporation of inertial droplets. These fluctuations decrease with the increase of the volume over which DNS data are averaged, as one might expect. In cloud observations, these fluctuations also come from other processes, such as entrainment/mixing below the observation level, secondary CCN activation, or variations of CCN activation at the cloud base. Despite large differences in the spatial and temporal scales, the mixing diagram often used in entrainment/mixing studies with aircraft data is remarkably similar for both DNS and cloud observations. We argue that the similarity questions applicability of heuristic ideas based on mixing between two air parcels (that the mixing diagram is designed to properly represent) to the evolution of microphysical properties during turbulent mixing between a cloud and its environment.

A three-dimensional sectional representation of aerosol mixing state for simulating optical properties and cloud condensation nuclei

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ching, Ping Pui; Zaveri, Rahul A.; Easter, Richard C.

2016-05-27

Light absorption by black carbon (BC) particles emitted from fossil fuel combustion depends on the how thickly they are coated with non-refractory species such as ammonium, sulfate, nitrate, organics, and water. The cloud condensation nuclei (CCN) activation property of a particle depends on its dry size and the hygroscopicities of all the individual species mixed together. It is therefore necessary to represent both size and mixing state of aerosols to reliably predict their climate-relevant properties in atmospheric models. Here we describe and evaluate a novel sectional framework in the Model for Simulating Aerosol Interactions and Chemistry, referred to as MOSAIC-mix,more » that represents the mixing state by resolving aerosol dry size (Ddry), BC dry mass fraction (wBC), and hygroscopicity (κ). Using ten idealized urban plume scenarios in which different types of aerosols evolve over 24 hours under a range of atmospherically relevant environmental conditions, we examine errors in CCN concentrations and optical properties with respect to a more explicit aerosol mixing state representation. We find that only a small number of wBC and κ bins are needed to achieve significant reductions in the errors, and propose a configuration consisting of 24 Ddry bins, 2 wBC bins, and 2 κ bins that gives 24-hour average errors of about 5% or less in CCN concentrations and optical properties, 3-4 times lower than those from size-only-resolved simulations. These results show that MOSAIC-mix is suitable for use in regional and global models to examine the effects of evolving aerosol mixing states on aerosol-radiation-cloud feedbacks.« less

RACORO continental boundary layer cloud investigations. Part I: Case study development and ensemble large-scale forcings

DOE PAGES

Vogelmann, Andrew M.; Fridlind, Ann M.; Toto, Tami; ...

2015-06-19

Observation-based modeling case studies of continental boundary layer clouds have been developed to study cloudy boundary layers, aerosol influences upon them, and their representation in cloud- and global-scale models. Three 60-hour case study periods span the temporal evolution of cumulus, stratiform, and drizzling boundary layer cloud systems, representing mixed and transitional states rather than idealized or canonical cases. Based on in-situ measurements from the RACORO field campaign and remote-sensing observations, the cases are designed with a modular configuration to simplify use in large-eddy simulations (LES) and single-column models. Aircraft measurements of aerosol number size distribution are fit to lognormal functionsmore » for concise representation in models. Values of the aerosol hygroscopicity parameter, κ, are derived from observations to be ~0.10, which are lower than the 0.3 typical over continents and suggestive of a large aerosol organic fraction. Ensemble large-scale forcing datasets are derived from the ARM variational analysis, ECMWF forecasts, and a multi-scale data assimilation system. The forcings are assessed through comparison of measured bulk atmospheric and cloud properties to those computed in 'trial' large-eddy simulations, where more efficient run times are enabled through modest reductions in grid resolution and domain size compared to the full-sized LES grid. Simulations capture many of the general features observed, but the state-of-the-art forcings were limited at representing details of cloud onset, and tight gradients and high-resolution transients of importance. Methods for improving the initial conditions and forcings are discussed. The cases developed are available to the general modeling community for studying continental boundary clouds.« less

RACORO Continental Boundary Layer Cloud Investigations: 1. Case Study Development and Ensemble Large-Scale Forcings

NASA Technical Reports Server (NTRS)

Vogelmann, Andrew M.; Fridlind, Ann M.; Toto, Tami; Endo, Satoshi; Lin, Wuyin; Wang, Jian; Feng, Sha; Zhang, Yunyan; Turner, David D.; Liu, Yangang;

RACORO continental boundary layer cloud investigations: 1. Case study development and ensemble large-scale forcings

NASA Astrophysics Data System (ADS)

Vogelmann, Andrew M.; Fridlind, Ann M.; Toto, Tami; Endo, Satoshi; Lin, Wuyin; Wang, Jian; Feng, Sha; Zhang, Yunyan; Turner, David D.; Liu, Yangang; Li, Zhijin; Xie, Shaocheng; Ackerman, Andrew S.; Zhang, Minghua; Khairoutdinov, Marat

2015-06-01

Observation-based modeling case studies of continental boundary layer clouds have been developed to study cloudy boundary layers, aerosol influences upon them, and their representation in cloud- and global-scale models. Three 60 h case study periods span the temporal evolution of cumulus, stratiform, and drizzling boundary layer cloud systems, representing mixed and transitional states rather than idealized or canonical cases. Based on in situ measurements from the Routine AAF (Atmospheric Radiation Measurement (ARM) Aerial Facility) CLOWD (Clouds with Low Optical Water Depth) Optical Radiative Observations (RACORO) field campaign and remote sensing observations, the cases are designed with a modular configuration to simplify use in large-eddy simulations (LES) and single-column models. Aircraft measurements of aerosol number size distribution are fit to lognormal functions for concise representation in models. Values of the aerosol hygroscopicity parameter, κ, are derived from observations to be 0.10, which are lower than the 0.3 typical over continents and suggestive of a large aerosol organic fraction. Ensemble large-scale forcing data sets are derived from the ARM variational analysis, European Centre for Medium-Range Weather Forecasts, and a multiscale data assimilation system. The forcings are assessed through comparison of measured bulk atmospheric and cloud properties to those computed in "trial" large-eddy simulations, where more efficient run times are enabled through modest reductions in grid resolution and domain size compared to the full-sized LES grid. Simulations capture many of the general features observed, but the state-of-the-art forcings were limited at representing details of cloud onset, and tight gradients and high-resolution transients of importance. Methods for improving the initial conditions and forcings are discussed. The cases developed are available to the general modeling community for studying continental boundary clouds.

A flavor symmetry model for bilarge leptonic mixing and the lepton masses

NASA Astrophysics Data System (ADS)

Ohlsson, Tommy; Seidl, Gerhart

2002-11-01

We present a model for leptonic mixing and the lepton masses based on flavor symmetries and higher-dimensional mass operators. The model predicts bilarge leptonic mixing (i.e., the mixing angles θ12 and θ23 are large and the mixing angle θ13 is small) and an inverted hierarchical neutrino mass spectrum. Furthermore, it approximately yields the experimental hierarchical mass spectrum of the charged leptons. The obtained values for the leptonic mixing parameters and the neutrino mass squared differences are all in agreement with atmospheric neutrino data, the Mikheyev-Smirnov-Wolfenstein large mixing angle solution of the solar neutrino problem, and consistent with the upper bound on the reactor mixing angle. Thus, we have a large, but not close to maximal, solar mixing angle θ12, a nearly maximal atmospheric mixing angle θ23, and a small reactor mixing angle θ13. In addition, the model predicts θ 12≃ {π}/{4}-θ 13.

A Global Modeling Study on Carbonaceous Aerosol Microphysical Characteristics and Radiative Effects

NASA Technical Reports Server (NTRS)

Bauer, S. E.; Menon, S.; Koch, D.; Bond, T. C.; Tsigaridis, K.

2010-01-01

Recently, attention has been drawn towards black carbon aerosols as a short-term climate warming mitigation candidate. However the global and regional impacts of the direct, indirect and semi-direct aerosol effects are highly uncertain, due to the complex nature of aerosol evolution and the way that mixed, aged aerosols interact with clouds and radiation. A detailed aerosol microphysical scheme, MATRIX, embedded within the GISS climate model is used in this study to present a quantitative assessment of the impact of microphysical processes involving black carbon, such as emission size distributions and optical properties on aerosol cloud activation and radiative effects. Our best estimate for net direct and indirect aerosol radiative flux change between 1750 and 2000 is -0.56 W/m2. However, the direct and indirect aerosol effects are quite sensitive to the black and organic carbon size distribution and consequential mixing state. The net radiative flux change can vary between -0.32 to -0.75 W/m2 depending on these carbonaceous particle properties at emission. Taking into account internally mixed black carbon particles let us simulate correct aerosol absorption. Absorption of black carbon aerosols is amplified by sulfate and nitrate coatings and, even more strongly, by organic coatings. Black carbon mitigation scenarios generally showed reduced radiative fluxeswhen sources with a large proportion of black carbon, such as diesel, are reduced; however reducing sources with a larger organic carbon component as well, such as bio-fuels, does not necessarily lead to a reduction in positive radiative flux.

A global modeling study on carbonaceous aerosol microphysical characteristics and radiative effects

NASA Astrophysics Data System (ADS)

Bauer, S. E.; Menon, S.; Koch, D.; Bond, T. C.; Tsigaridis, K.

2010-08-01

Recently, attention has been drawn towards black carbon aerosols as a short-term climate warming mitigation candidate. However the global and regional impacts of the direct, indirect and semi-direct aerosol effects are highly uncertain, due to the complex nature of aerosol evolution and the way that mixed, aged aerosols interact with clouds and radiation. A detailed aerosol microphysical scheme, MATRIX, embedded within the GISS climate model is used in this study to present a quantitative assessment of the impact of microphysical processes involving black carbon, such as emission size distributions and optical properties on aerosol cloud activation and radiative effects. Our best estimate for net direct and indirect aerosol radiative flux change between 1750 and 2000 is -0.56 W/m2. However, the direct and indirect aerosol effects are quite sensitive to the black and organic carbon size distribution and consequential mixing state. The net radiative flux change can vary between -0.32 to -0.75 W/m2 depending on these carbonaceous particle properties at emission. Taking into account internally mixed black carbon particles let us simulate correct aerosol absorption. Absorption of black carbon aerosols is amplified by sulfate and nitrate coatings and, even more strongly, by organic coatings. Black carbon mitigation scenarios generally showed reduced radiative fluxeswhen sources with a large proportion of black carbon, such as diesel, are reduced; however reducing sources with a larger organic carbon component as well, such as bio-fuels, does not necessarily lead to a reduction in positive radiative flux.

Examining Atmospheric and Ecological Drivers of Wildfires, Modeling Wildfire Occurrence in the Southwest United States, and Using Atmospheric Sounding Observations to Verify National Weather Service Spot Forecasts

NASA Astrophysics Data System (ADS)

Nauslar, Nicholas J.

This dissertation is comprised of three different papers that all pertain to wildland fire applications. The first paper performs a verification analysis on mixing height, transport winds, and Haines Index from National Weather Service spot forecasts across the United States. The final two papers, which are closely related, examine atmospheric and ecological drivers of wildfire for the Southwest Area (SWA) (Arizona, New Mexico, west Texas, and Oklahoma panhandle) to better equip operational fire meteorologists and managers to make informed decisions on wildfire potential in this region. The verification analysis here utilizes NWS spot forecasts of mixing height, transport winds and Haines Index from 2009-2013 issued for a location within 50 km of an upper sounding location and valid for the day of the fire event. Mixing height was calculated from the 0000 UTC sounding via the Stull, Holzworth, and Richardson methods. Transport wind speeds were determined by averaging the wind speed through the boundary layer as determined by the three mixing height methods from the 0000 UTC sounding. Haines Index was calculated at low, mid, and high elevation based on the elevation of the sounding and spot forecast locations. Mixing height forecasts exhibited large mean absolute errors and biased towards over forecasting. Forecasts of transport wind speeds and Haines Index outperformed mixing height forecasts with smaller errors relative to their respective means. The rainfall and lightning associated with the North American Monsoon (NAM) can vary greatly intra- and inter-annually and has a large impact on wildfire activity across the SWA by igniting or suppressing wildfires. NAM onset thresholds and subsequent dates are determined for the SWA and each Predictive Service Area (PSA), which are sub-regions used by operational fire meteorologists to predict wildfire potential within the SWA, April through September from 1995-2013. Various wildfire activity thresholds using the number of wildfires and large wildfires identified days or time periods with increased wildfire activity for each PSA and the SWA. Self-organizing maps utilizing 500 and 700 hPa geopotential heights and precipitable water were implemented to identify atmospheric patterns contributing to the NAM onset and busy days/periods for each PSA and the SWA. Resulting SOM map types also showed the transition to, during, and from the NAM. Northward and eastward displacements of the subtropical ridge (i.e., four-corners high) over the SWA were associated with NAM onset, and a suppressed subtropical ridge and breakdown of the subtropical ridge map types over the SWA were associated with increased wildfire activity. We implemented boosted regression trees (BRT) to model wildfire occurrence for all and large wildfires for different wildfire types (i.e., lightning, human) across the SWA by PSA. BRT models for all wildfires demonstrated relatively small mean and mean absolute errors and showed better predictability on days with wildfires. Cross-validated accuracy assessments for large wildfires demonstrated the ability to discriminate between large wildfire and non-large wildfire days across all wildfire types. Measurements describing fuel conditions (i.e., 100 and 1000-hour dead fuel moisture, energy release component) were the most important predictors when considering all wildfire types and sizes. However, a combination of fuels and atmospheric predictors (i.e., lightning, temperature) proved most predictive for large wildfire occurrence, and the number of relevant predictors increases for large wildfires indicating more conditions need to align to support large wildfires.

Are Social Networking Sites Making Health Behavior Change Interventions More Effective? A Meta-Analytic Review.

PubMed

Yang, Qinghua

2017-03-01

The increasing popularity of social networking sites (SNSs) has drawn scholarly attention in recent years, and a large amount of efforts have been made in applying SNSs to health behavior change interventions. However, these interventions showed mixed results, with a large variance of effect sizes in Cohen's d ranging from -1.17 to 1.28. To provide a better understanding of SNS-based interventions' effectiveness, a meta-analysis of 21 studies examining the effects of health interventions using SNS was conducted. Results indicated that health behavior change interventions using SNS are effective in general, but the effects were moderated by health topic, methodological features, and participant features. Theoretical and practical implications of findings are discussed.

Modeling optimal treatment strategies in a heterogeneous mixing model.

PubMed

Choe, Seoyun; Lee, Sunmi

2015-11-25

Many mathematical models assume random or homogeneous mixing for various infectious diseases. Homogeneous mixing can be generalized to mathematical models with multi-patches or age structure by incorporating contact matrices to capture the dynamics of the heterogeneously mixing populations. Contact or mixing patterns are difficult to measure in many infectious diseases including influenza. Mixing patterns are considered to be one of the critical factors for infectious disease modeling. A two-group influenza model is considered to evaluate the impact of heterogeneous mixing on the influenza transmission dynamics. Heterogeneous mixing between two groups with two different activity levels includes proportionate mixing, preferred mixing and like-with-like mixing. Furthermore, the optimal control problem is formulated in this two-group influenza model to identify the group-specific optimal treatment strategies at a minimal cost. We investigate group-specific optimal treatment strategies under various mixing scenarios. The characteristics of the two-group influenza dynamics have been investigated in terms of the basic reproduction number and the final epidemic size under various mixing scenarios. As the mixing patterns become proportionate mixing, the basic reproduction number becomes smaller; however, the final epidemic size becomes larger. This is due to the fact that the number of infected people increases only slightly in the higher activity level group, while the number of infected people increases more significantly in the lower activity level group. Our results indicate that more intensive treatment of both groups at the early stage is the most effective treatment regardless of the mixing scenario. However, proportionate mixing requires more treated cases for all combinations of different group activity levels and group population sizes. Mixing patterns can play a critical role in the effectiveness of optimal treatments. As the mixing becomes more like-with-like mixing, treating the higher activity group in the population is almost as effective as treating the entire populations since it reduces the number of disease cases effectively but only requires similar treatments. The gain becomes more pronounced as the basic reproduction number increases. This can be a critical issue which must be considered for future pandemic influenza interventions, especially when there are limited resources available.

Double-strand breaks in genome-sized DNA caused by mechanical stress under mixing: Quantitative evaluation through single-molecule observation

NASA Astrophysics Data System (ADS)

Kikuchi, Hayato; Nose, Keiji; Yoshikawa, Yuko; Yoshikawa, Kenichi

2018-06-01

It is becoming increasingly apparent that changes in the higher-order structure of genome-sized DNA molecules of more than several tens kbp play important roles in the self-control of genome activity in living cells. Unfortunately, it has been rather difficult to prepare genome-sized DNA molecules without damage or fragmentation. Here, we evaluated the degree of double-strand breaks (DSBs) caused by mechanical mixing by single-molecule observation with fluorescence microscopy. The results show that DNA breaks are most significant for the first second after the initiation of mechanical agitation. Based on such observation, we propose a novel mixing procedure to significantly decrease DSBs.

Theoretical investigation of mixing in warm clouds – Part 2: Homogeneous mixing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinsky, Mark; Khain, Alexander; Korolev, Alexei

Evolution of monodisperse and polydisperse droplet size distributions (DSD) during homogeneous mixing is analyzed. Time-dependent universal analytical expressions for supersaturation and liquid water content are derived. For an initial monodisperse DSD, these quantities are shown to depend on a sole non-dimensional parameter. The evolution of moments and moment-related functions in the course of homogeneous evaporation of polydisperse DSD is analyzed using a parcel model. It is shown that the classic conceptual scheme, according to which homogeneous mixing leads to a decrease in droplet mass at constant droplet concentration, is valid only in cases of monodisperse or initially very narrow polydispersemore » DSD. In cases of wide polydisperse DSD, mixing and successive evaporation lead to a decrease of both mass and concentration, so the characteristic droplet sizes remain nearly constant. As this feature is typically associated with inhomogeneous mixing, we conclude that in cases of an initially wide DSD at cloud top, homogeneous mixing is nearly indistinguishable from inhomogeneous mixing.« less

Theoretical investigation of mixing in warm clouds – Part 2: Homogeneous mixing

DOE PAGES

Pinsky, Mark; Khain, Alexander; Korolev, Alexei; ...

2016-07-28

Evolution of monodisperse and polydisperse droplet size distributions (DSD) during homogeneous mixing is analyzed. Time-dependent universal analytical expressions for supersaturation and liquid water content are derived. For an initial monodisperse DSD, these quantities are shown to depend on a sole non-dimensional parameter. The evolution of moments and moment-related functions in the course of homogeneous evaporation of polydisperse DSD is analyzed using a parcel model. It is shown that the classic conceptual scheme, according to which homogeneous mixing leads to a decrease in droplet mass at constant droplet concentration, is valid only in cases of monodisperse or initially very narrow polydispersemore » DSD. In cases of wide polydisperse DSD, mixing and successive evaporation lead to a decrease of both mass and concentration, so the characteristic droplet sizes remain nearly constant. As this feature is typically associated with inhomogeneous mixing, we conclude that in cases of an initially wide DSD at cloud top, homogeneous mixing is nearly indistinguishable from inhomogeneous mixing.« less

Modeling the soil water retention curves of soil-gravel mixtures with regression method on the Loess Plateau of China.

PubMed

Wang, Huifang; Xiao, Bo; Wang, Mingyu; Shao, Ming'an

2013-01-01

Soil water retention parameters are critical to quantify flow and solute transport in vadose zone, while the presence of rock fragments remarkably increases their variability. Therefore a novel method for determining water retention parameters of soil-gravel mixtures is required. The procedure to generate such a model is based firstly on the determination of the quantitative relationship between the content of rock fragments and the effective saturation of soil-gravel mixtures, and then on the integration of this relationship with former analytical equations of water retention curves (WRCs). In order to find such relationships, laboratory experiments were conducted to determine WRCs of soil-gravel mixtures obtained with a clay loam soil mixed with shale clasts or pebbles in three size groups with various gravel contents. Data showed that the effective saturation of the soil-gravel mixtures with the same kind of gravels within one size group had a linear relation with gravel contents, and had a power relation with the bulk density of samples at any pressure head. Revised formulas for water retention properties of the soil-gravel mixtures are proposed to establish the water retention curved surface models of the power-linear functions and power functions. The analysis of the parameters obtained by regression and validation of the empirical models showed that they were acceptable by using either the measured data of separate gravel size group or those of all the three gravel size groups having a large size range. Furthermore, the regression parameters of the curved surfaces for the soil-gravel mixtures with a large range of gravel content could be determined from the water retention data of the soil-gravel mixtures with two representative gravel contents or bulk densities. Such revised water retention models are potentially applicable in regional or large scale field investigations of significantly heterogeneous media, where various gravel sizes and different gravel contents are present.

Modeling the Soil Water Retention Curves of Soil-Gravel Mixtures with Regression Method on the Loess Plateau of China

PubMed Central

Wang, Huifang; Xiao, Bo; Wang, Mingyu; Shao, Ming'an

2013-01-01

Soil water retention parameters are critical to quantify flow and solute transport in vadose zone, while the presence of rock fragments remarkably increases their variability. Therefore a novel method for determining water retention parameters of soil-gravel mixtures is required. The procedure to generate such a model is based firstly on the determination of the quantitative relationship between the content of rock fragments and the effective saturation of soil-gravel mixtures, and then on the integration of this relationship with former analytical equations of water retention curves (WRCs). In order to find such relationships, laboratory experiments were conducted to determine WRCs of soil-gravel mixtures obtained with a clay loam soil mixed with shale clasts or pebbles in three size groups with various gravel contents. Data showed that the effective saturation of the soil-gravel mixtures with the same kind of gravels within one size group had a linear relation with gravel contents, and had a power relation with the bulk density of samples at any pressure head. Revised formulas for water retention properties of the soil-gravel mixtures are proposed to establish the water retention curved surface models of the power-linear functions and power functions. The analysis of the parameters obtained by regression and validation of the empirical models showed that they were acceptable by using either the measured data of separate gravel size group or those of all the three gravel size groups having a large size range. Furthermore, the regression parameters of the curved surfaces for the soil-gravel mixtures with a large range of gravel content could be determined from the water retention data of the soil-gravel mixtures with two representative gravel contents or bulk densities. Such revised water retention models are potentially applicable in regional or large scale field investigations of significantly heterogeneous media, where various gravel sizes and different gravel contents are present. PMID:23555040

Special Education Program Standards Study. Commonwealth of Virginia. Final Technical Report.

ERIC Educational Resources Information Center

Keith, Timothy Z.; And Others

This federally funded study investigated Virginia special education program standards, focusing on local applications of the standards for class size and class mix and the effect of varying class size and class mix on student outcomes. The study concentrated on students with educable mental retardation, severe emotional disturbance, and specific…

Window decompression in laser-heated MagLIF targets

NASA Astrophysics Data System (ADS)

Woodbury, Daniel; Peterson, Kyle; Sefkow, Adam

2015-11-01

The Magnetized Liner Inertial Fusion (MagLIF) concept requires pre-magnetized fuel to be pre-heated with a laser before undergoing compression by a thick solid liner. Recent experiments and simulations suggest that yield has been limited to date by poor laser preheat and laser-induced mix in the fuel region. In order to assess laser energy transmission through the pressure-holding window, as well as resultant mix, we modeled window disassembly under different conditions using 1D and 2D simulations in both Helios and HYDRA. We present results tracking energy absorption, time needed for decompression, risk of laser-plasma interaction (LPI) that may scatter laser light, and potential for mix from various window thicknesses, laser spot sizes and gas fill densities. These results indicate that using thinner windows (0.5-1 μm windows) and relatively large laser spot radii (600 μm and above) can avoid deleterious effects and improve coupling with the fuel. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the National Nuclear Security Administration under DE-AC04- 94AL85000.

Resolving Size Distribution of Black Carbon Internally Mixed With Snow: Impact on Snow Optical Properties and Albedo

NASA Astrophysics Data System (ADS)

He, Cenlin; Liou, Kuo-Nan; Takano, Yoshi

2018-03-01

We develop a stochastic aerosol-snow albedo model that explicitly resolves size distribution of aerosols internally mixed with various snow grains. We use the model to quantify black carbon (BC) size effects on snow albedo and optical properties for BC-snow internal mixing. Results show that BC-induced snow single-scattering coalbedo enhancement and albedo reduction decrease by a factor of 2-3 with increasing BC effective radii from 0.05 to 0.25 μm, while polydisperse BC results in up to 40% smaller visible single-scattering coalbedo enhancement and albedo reduction compared to monodisperse BC with equivalent effective radii. We further develop parameterizations for BC size effects for application to climate models. Compared with a realistic polydisperse assumption and observed shifts to larger BC sizes in snow, respectively, assuming monodisperse BC and typical atmospheric BC effective radii could lead to overestimates of 24% and 40% in BC-snow albedo forcing averaged over different BC and snow conditions.

Impact of Grain Shape and Multiple Black Carbon Internal Mixing on Snow Albedo: Parameterization and Radiative Effect Analysis

NASA Astrophysics Data System (ADS)

He, Cenlin; Liou, Kuo-Nan; Takano, Yoshi; Yang, Ping; Qi, Ling; Chen, Fei

2018-01-01

We quantify the effects of grain shape and multiple black carbon (BC)-snow internal mixing on snow albedo by explicitly resolving shape and mixing structures. Nonspherical snow grains tend to have higher albedos than spheres with the same effective sizes, while the albedo difference due to shape effects increases with grain size, with up to 0.013 and 0.055 for effective radii of 1,000 μm at visible and near-infrared bands, respectively. BC-snow internal mixing reduces snow albedo at wavelengths < 1.5 μm, with negligible effects at longer wavelengths. Nonspherical snow grains show less BC-induced albedo reductions than spheres with the same effective sizes by up to 0.06 at ultraviolet and visible bands. Compared with external mixing, internal mixing enhances snow albedo reduction by a factor of 1.2-2.0 at visible wavelengths depending on BC concentration and snow shape. The opposite effects on albedo reductions due to snow grain nonsphericity and BC-snow internal mixing point toward a careful investigation of these two factors simultaneously in climate modeling. We further develop parameterizations for snow albedo and its reduction by accounting for grain shape and BC-snow internal/external mixing. Combining the parameterizations with BC-in-snow measurements in China, North America, and the Arctic, we estimate that nonspherical snow grains reduce BC-induced albedo radiative effects by up to 50% compared with spherical grains. Moreover, BC-snow internal mixing enhances the albedo effects by up to 30% (130%) for spherical (nonspherical) grains relative to external mixing. The overall uncertainty induced by snow shape and BC-snow mixing state is about 21-32%.

Image quality of mixed convolution kernel in thoracic computed tomography.

PubMed

Neubauer, Jakob; Spira, Eva Maria; Strube, Juliane; Langer, Mathias; Voss, Christian; Kotter, Elmar

2016-11-01

The mixed convolution kernel alters his properties geographically according to the depicted organ structure, especially for the lung. Therefore, we compared the image quality of the mixed convolution kernel to standard soft and hard kernel reconstructions for different organ structures in thoracic computed tomography (CT) images.Our Ethics Committee approved this prospective study. In total, 31 patients who underwent contrast-enhanced thoracic CT studies were included after informed consent. Axial reconstructions were performed with hard, soft, and mixed convolution kernel. Three independent and blinded observers rated the image quality according to the European Guidelines for Quality Criteria of Thoracic CT for 13 organ structures. The observers rated the depiction of the structures in all reconstructions on a 5-point Likert scale. Statistical analysis was performed with the Friedman Test and post hoc analysis with the Wilcoxon rank-sum test.Compared to the soft convolution kernel, the mixed convolution kernel was rated with a higher image quality for lung parenchyma, segmental bronchi, and the border between the pleura and the thoracic wall (P < 0.03). Compared to the hard convolution kernel, the mixed convolution kernel was rated with a higher image quality for aorta, anterior mediastinal structures, paratracheal soft tissue, hilar lymph nodes, esophagus, pleuromediastinal border, large and medium sized pulmonary vessels and abdomen (P < 0.004) but a lower image quality for trachea, segmental bronchi, lung parenchyma, and skeleton (P < 0.001).The mixed convolution kernel cannot fully substitute the standard CT reconstructions. Hard and soft convolution kernel reconstructions still seem to be mandatory for thoracic CT.

Sediment fingerprinting experiments to test the sensitivity of multivariate mixing models

NASA Astrophysics Data System (ADS)

Gaspar, Leticia; Blake, Will; Smith, Hugh; Navas, Ana

2014-05-01

Sediment fingerprinting techniques provide insight into the dynamics of sediment transfer processes and support for catchment management decisions. As questions being asked of fingerprinting datasets become increasingly complex, validation of model output and sensitivity tests are increasingly important. This study adopts an experimental approach to explore the validity and sensitivity of mixing model outputs for materials with contrasting geochemical and particle size composition. The experiments reported here focused on (i) the sensitivity of model output to different fingerprint selection procedures and (ii) the influence of source material particle size distributions on model output. Five soils with significantly different geochemistry, soil organic matter and particle size distributions were selected as experimental source materials. A total of twelve sediment mixtures were prepared in the laboratory by combining different quantified proportions of the < 63 µm fraction of the five source soils i.e. assuming no fluvial sorting of the mixture. The geochemistry of all source and mixture samples (5 source soils and 12 mixed soils) were analysed using X-ray fluorescence (XRF). Tracer properties were selected from 18 elements for which mass concentrations were found to be significantly different between sources. Sets of fingerprint properties that discriminate target sources were selected using a range of different independent statistical approaches (e.g. Kruskal-Wallis test, Discriminant Function Analysis (DFA), Principal Component Analysis (PCA), or correlation matrix). Summary results for the use of the mixing model with the different sets of fingerprint properties for the twelve mixed soils were reasonably consistent with the initial mixing percentages initially known. Given the experimental nature of the work and dry mixing of materials, geochemical conservative behavior was assumed for all elements, even for those that might be disregarded in aquatic systems (e.g. P). In general, the best fits between actual and modeled proportions were found using a set of nine tracer properties (Sr, Rb, Fe, Ti, Ca, Al, P, Si, K, Si) that were derived using DFA coupled with a multivariate stepwise algorithm, with errors between real and estimated value that did not exceed 6.7 % and values of GOF above 94.5 %. The second set of experiments aimed to explore the sensitivity of model output to variability in the particle size of source materials assuming that a degree of fluvial sorting of the resulting mixture took place. Most particle size correction procedures assume grain size affects are consistent across sources and tracer properties which is not always the case. Consequently, the < 40 µm fraction of selected soil mixtures was analysed to simulate the effect of selective fluvial transport of finer particles and the results were compared to those for source materials. Preliminary findings from this experiment demonstrate the sensitivity of the numerical mixing model outputs to different particle size distributions of source material and the variable impact of fluvial sorting on end member signatures used in mixing models. The results suggest that particle size correction procedures require careful scrutiny in the context of variable source characteristics.

CFD simulation of gas and non-Newtonian fluid two-phase flow in anaerobic digesters.

PubMed

Wu, Binxin

2010-07-01

This paper presents an Eulerian multiphase flow model that characterizes gas mixing in anaerobic digesters. In the model development, liquid manure is assumed to be water or a non-Newtonian fluid that is dependent on total solids (TS) concentration. To establish the appropriate models for different TS levels, twelve turbulence models are evaluated by comparing the frictional pressure drops of gas and non-Newtonian fluid two-phase flow in a horizontal pipe obtained from computational fluid dynamics (CFD) with those from a correlation analysis. The commercial CFD software, Fluent12.0, is employed to simulate the multiphase flow in the digesters. The simulation results in a small-sized digester are validated against the experimental data from literature. Comparison of two gas mixing designs in a medium-sized digester demonstrates that mixing intensity is insensitive to the TS in confined gas mixing, whereas there are significant decreases with increases of TS in unconfined gas mixing. Moreover, comparison of three mixing methods indicates that gas mixing is more efficient than mixing by pumped circulation while it is less efficient than mechanical mixing.

Lower tropospheric distributions of O3 and aerosol over Raoyang, a rural site in the North China Plain

NASA Astrophysics Data System (ADS)

Wang, Rui; Xu, Xiaobin; Jia, Shihui; Ma, Ruisheng; Ran, Liang; Deng, Zhaoze; Lin, Weili; Wang, Ying; Ma, Zhiqiang

2017-03-01

The North China Plain (NCP) has become one of the most polluted regions in China, with the rapidly increasing economic growth in the past decades. High concentrations of ambient O3 and aerosol have been observed at urban as well as rural sites in the NCP. Most of the in situ observations of air pollutants have been conducted near the ground so that current knowledge about the vertical distributions of tropospheric O3 and aerosol over the NCP region is still limited. In this study, vertical profiles of O3 and size-resolved aerosol concentrations below 2.5 km were measured in summer 2014 over a rural site in the NCP, using an unmanned aerial vehicle (UAV) equipped with miniature analyzers. In addition, vertical profiles of aerosol scattering property in the lower troposphere and vertical profiles of O3 below 1 km were also observed at the site using a lidar and tethered balloon, respectively. The depths of the mixed layer and residual layer were determined according to the vertical gradients of lidar particle extinction and aerosol number concentration. Average O3 and size-resolved aerosol number concentration in both the mixed and residual layer were obtained from the data observed in seven UAV flights. The results show that during most of the flights the O3 levels above the top of mixed layer were higher than those below. Such a positive gradient in the vertical distribution of O3 makes the residual layer an important source of O3 in the mixed layer, particularly during the morning when the top of mixed layer is rapidly elevated. In contrast to O3, aerosol number concentration was normally higher in the mixed layer than in the residual layer, particularly in the early morning. Aerosol particles were overwhelmingly distributed in the size range < 1 µm, showing slight differences between the mixed and residual layers. Our measurements confirm that the lower troposphere over the rural area of the NCP is largely impacted by anthropogenic pollutants locally emitted or transported from urban areas. Compared with the historic O3 vertical profiles over Beijing from the Measurement of Ozone and Water Vapor by Airbus In-Service Aircraft (MOZAIC), a strong increase in O3 can be found at all heights below 2.5 km in the decade from 2004 to 2014, with the largest enhancement of about 41.6 ppb. This indicates that the lower troposphere over the northern part of the NCP has experienced rapidly worsening photochemical pollution. This worsening trend in photochemical pollution deserves more attention in the future.

Frazil-ice growth rate and dynamics in mixed layers and sub-ice-shelf plumes

NASA Astrophysics Data System (ADS)

Rees Jones, David W.; Wells, Andrew J.

2018-01-01

The growth of frazil or granular ice is an important mode of ice formation in the cryosphere. Recent advances have improved our understanding of the microphysical processes that control the rate of ice-crystal growth when water is cooled beneath its freezing temperature. These advances suggest that crystals grow much faster than previously thought. In this paper, we consider models of a population of ice crystals with different sizes to provide insight into the treatment of frazil ice in large-scale models. We consider the role of crystal growth alongside the other physical processes that determine the dynamics of frazil ice. We apply our model to a simple mixed layer (such as at the surface of the ocean) and to a buoyant plume under a floating ice shelf. We provide numerical calculations and scaling arguments to predict the occurrence of frazil-ice explosions, which we show are controlled by crystal growth, nucleation, and gravitational removal. Faster crystal growth, higher secondary nucleation, and slower gravitational removal make frazil-ice explosions more likely. We identify steady-state crystal size distributions, which are largely insensitive to crystal growth rate but are affected by the relative importance of secondary nucleation to gravitational removal. Finally, we show that the fate of plumes underneath ice shelves is dramatically affected by frazil-ice dynamics. Differences in the parameterization of crystal growth and nucleation give rise to radically different predictions of basal accretion and plume dynamics, and can even impact whether a plume reaches the end of the ice shelf or intrudes at depth.

DISTMIX: direct imputation of summary statistics for unmeasured SNPs from mixed ethnicity cohorts.

PubMed

Lee, Donghyung; Bigdeli, T Bernard; Williamson, Vernell S; Vladimirov, Vladimir I; Riley, Brien P; Fanous, Ayman H; Bacanu, Silviu-Alin

2015-10-01

To increase the signal resolution for large-scale meta-analyses of genome-wide association studies, genotypes at unmeasured single nucleotide polymorphisms (SNPs) are commonly imputed using large multi-ethnic reference panels. However, the ever increasing size and ethnic diversity of both reference panels and cohorts makes genotype imputation computationally challenging for moderately sized computer clusters. Moreover, genotype imputation requires subject-level genetic data, which unlike summary statistics provided by virtually all studies, is not publicly available. While there are much less demanding methods which avoid the genotype imputation step by directly imputing SNP statistics, e.g. Directly Imputing summary STatistics (DIST) proposed by our group, their implicit assumptions make them applicable only to ethnically homogeneous cohorts. To decrease computational and access requirements for the analysis of cosmopolitan cohorts, we propose DISTMIX, which extends DIST capabilities to the analysis of mixed ethnicity cohorts. The method uses a relevant reference panel to directly impute unmeasured SNP statistics based only on statistics at measured SNPs and estimated/user-specified ethnic proportions. Simulations show that the proposed method adequately controls the Type I error rates. The 1000 Genomes panel imputation of summary statistics from the ethnically diverse Psychiatric Genetic Consortium Schizophrenia Phase 2 suggests that, when compared to genotype imputation methods, DISTMIX offers comparable imputation accuracy for only a fraction of computational resources. DISTMIX software, its reference population data, and usage examples are publicly available at http://code.google.com/p/distmix. dlee4@vcu.edu Supplementary Data are available at Bioinformatics online. © The Author 2015. Published by Oxford University Press.

Mixing at double-Tee junctions with unequal pipe sizes in water distribution systems

EPA Science Inventory

Pipe flow mixing with various solute concentrations and flow rates at pipe junctions is investigated. The degree of mixing affects the spread of contaminants in a water distribution system. Many studies have been conducted on the mixing at the cross junctions. Yet a few have focu...

Electrokinetic mixing at high zeta potentials: ionic size effects on cross stream diffusion.

PubMed

Ahmadian Yazdi, Alireza; Sadeghi, Arman; Saidi, Mohammad Hassan

2015-03-15

The electrokinetic phenomena at high zeta potentials may show several unique features which are not normally observed. One of these features is the ionic size (steric) effect associated with the solutions of high ionic concentration. In the present work, attention is given to the influences of finite ionic size on the cross stream diffusion process in an electrokinetically actuated Y-shaped micromixer. The method consists of a finite difference based numerical approach for non-uniform grid which is applied to the dimensionless form of the governing equations, including the modified Poisson-Boltzmann equation. The results reveal that, neglecting the ionic size at high zeta potentials gives rise to the overestimation of the mixing length, because the steric effects retard liquid flow, thereby enhancing the mixing efficiency. The importance of steric effects is found to be more intense for channels of smaller width to height ratio. It is also observed that, in sharp contrast to the conditions that the ions are treated as point charges, increasing the zeta potential improves the cross stream diffusion when incorporating the ionic size. Moreover, increasing the EDL thickness decreases the mixing length, whereas the opposite is true for the channel aspect ratio. Copyright © 2014 Elsevier Inc. All rights reserved.

Men, women…who cares? A population-based study on sex differences and gender roles in empathy and moral cognition.

PubMed

Baez, Sandra; Flichtentrei, Daniel; Prats, María; Mastandueno, Ricardo; García, Adolfo M; Cetkovich, Marcelo; Ibáñez, Agustín

2017-01-01

Research on sex differences in empathy has revealed mixed findings. Whereas experimental and neuropsychological measures show no consistent sex effect, self-report data consistently indicates greater empathy in women. However, available results mainly come from separate populations with relatively small samples, which may inflate effect sizes and hinder comparability between both empirical corpora. To elucidate the issue, we conducted two large-scale studies. First, we examined whether sex differences emerge in a large population-based sample (n = 10,802) when empathy is measured with an experimental empathy-for-pain paradigm. Moreover, we investigated the relationship between empathy and moral judgment. In the second study, a subsample (n = 334) completed a self-report empathy questionnaire. Results showed some sex differences in the experimental paradigm, but with minuscule effect sizes. Conversely, women did portray themselves as more empathic through self-reports. In addition, utilitarian responses to moral dilemmas were less frequent in women, although these differences also had small effect sizes. These findings suggest that sex differences in empathy are highly driven by the assessment measure. In particular, self-reports may induce biases leading individuals to assume gender-role stereotypes. Awareness of the role of measurement instruments in this field may hone our understanding of the links between empathy, sex differences, and gender roles.

Properties of jet engine combustion particles during the PartEmis experiment: Microphysics and Chemistry

NASA Astrophysics Data System (ADS)

Petzold, A.; Stein, C.; Nyeki, S.; Gysel, M.; Weingartner, E.; Baltensperger, U.; Giebl, H.; Hitzenberger, R.; Döpelheuer, A.; Vrchoticky, S.; Puxbaum, H.; Johnson, M.; Hurley, C. D.; Marsh, R.; Wilson, C. W.

2003-07-01

The particles emitted from an aircraft engine combustor were investigated in the European project PartEmis. Measured aerosol properties were mass and number concentration, size distribution, mixing state, thermal stability of internally mixed particles, hygroscopicity, and cloud condensation nuclei (CCN) activation potential. The combustor operation conditions corresponded to modern and older engine gas path temperatures at cruise altitude, with fuel sulphur contents (FSC) of 50, 410, and 1270 μg g-1. Operation conditions and FSC showed only a weak influence on the microphysical aerosol properties, except for hygroscopic and CCN properties. Particles of size D >= 30 nm were almost entirely internally mixed. Particles of sizes D < 20 nm showed a considerable volume fraction of compounds that volatilise at 390 K (10-15%) and 573 K (4-10%), while respective fractions decreased to <5% for particles of size D >= 50 nm.

Origin, distribution, and rapid removal of hydrothermally formed clay at Mount Baker, Washington

USGS Publications Warehouse

Frank, David

1983-01-01

Clay minerals are locally abundant in two hydrothermal areas at Mount Baker-Sherman Crater and the Dorr Fumarole Field. The silt- and clay-size fractions of volcanic debris that is undergoing alteration at and near the ground surface around areas of current fumarolic activity in Sherman Crater are largely dominated by alunite and a silica phase, either opal or cristobalite, but contain some kaolinite and smectite. Correspondingly, the chemistry of solutions at the surface of the crater, as represented by the crater lake, favors the formation of alunite over kaolinite. In contrast, vent-filling debris that was ejected to the surface from fumaroles in 1975 contains more than 20 percent clay-size material in which kaolinite and smectite are dominant. The youngest eruptive deposit (probably 19th century) on the crater rim was also altered prior to ejection and contains as much as 27 percent clay-size material in which kaolinite, smectite, pyrophyllite, and mixed-layer illitesmectite are abundant. The hydrothermal products, kaolinite and alunite, are present in significant amounts in five large Holocene mudflows that originated at the upper cone of Mount Baker. The distribution of kaolinite in crater and valley deposits indicates that, with the passage of time, increasingly greater amounts of this clay mineral have been incorporated into large mass movements from the upper cone. Either erosion has cut into more kaolinitic parts of the core of Sherman Crater, or the amount of kaolinite has increased through time in Sherman Crater.

Is recurrence in major depressive disorder related to bipolarity and mixed features? Results from the BRIDGE-II-Mix study.

PubMed

Mazzarini, Lorenzo; Kotzalidis, Georgios D; Piacentino, Daria; Rizzato, Salvatore; Angst, Jules; Azorin, Jean-Michel; Bowden, Charles L; Mosolov, Sergey; Young, Allan H; Vieta, Eduard; Girardi, Paolo; Perugi, Giulio

2018-03-15

Current classifications separate Bipolar (BD) from Major Depressive Disorder (MDD) based on polarity rather than recurrence. We aimed to determine bipolar/mixed feature frequency in a large MDD multinational sample with (High-Rec) and without (Low-Rec) >3 recurrences, comparing the two subsamples. We measured frequency of bipolarity/hypomanic features during current depressive episodes (MDEs) in 2347 MDD patients from the BRIDGE-II-mix database, comparing High-Rec with Low-Rec. We used Bonferroni-corrected Student's t-test for continuous, and chi-squared test, for categorical variables. Logistic regression estimated the size of the association between clinical characteristics and High-Rec MDD. Compared to Low-Rec (n = 1084, 46.2%), High-Rec patients (n = 1263, 53.8%) were older, with earlier depressive onset, had more family history of BD, more atypical features, suicide attempts, hospitalisations, and treatment resistance and (hypo)manic switches when treated with antidepressants, higher comorbidity with borderline personality disorder, and more hypomanic symptoms during current MDE, resulting in higher rates of mixed depression according to both DSM-5 and research-based diagnostic (RBDC) criteria. Logistic regression showed age at first symptoms < 30 years, current MDE duration ≤ 1 month, hypomania/mania among first-degree relatives, past suicide attempts, treatment-resistance, antidepressant-induced swings, and atypical, mixed, or psychotic features during MDE to associate with High-Rec. Number of MDEs for defining recurrence was arbitrary; cross-sectionality did not allow assessment of conversion from MDD to BD. High-Rec MDD differed from Low-Rec group for several clinical/epidemiological variables, including bipolar/mixed features. Bipolarity specifier and RBDC were more sensitive than DSM-5 criteria in detecting bipolar and mixed features in MDD. Copyright © 2017. Published by Elsevier B.V.

Visualization of Oil Body Distribution in Jatropha curcas L. by Four-Wave Mixing Microscopy

NASA Astrophysics Data System (ADS)

Ishii, Makiko; Uchiyama, Susumu; Ozeki, Yasuyuki; Kajiyama, Sin'ichiro; Itoh, Kazuyoshi; Fukui, Kiichi

2013-06-01

Jatropha curcas L. (jatropha) is a superior oil crop for biofuel production. To improve the oil yield of jatropha by breeding, the development of effective and reliable tools to evaluate the oil production efficiency is essential. The characteristics of the jatropha kernel, which contains a large amount of oil, are not fully understood yet. Here, we demonstrate the application of four-wave mixing (FWM) microscopy to visualize the distribution of oil bodies in a jatropha kernel without staining. FWM microscopy enables us to visualize the size and morphology of oil bodies and to determine the oil content in the kernel to be 33.2%. The signal obtained from FWM microscopy comprises both of stimulated parametric emission (SPE) and coherent anti-Stokes Raman scattering (CARS) signals. In the present situation, where a very short pump pulse is employed, the SPE signal is believed to dominate the FWM signal.

Chemical and Physical Properties of Individual Aerosol Particles Characterized in Sacramento, CA during CARES Field Campaign

NASA Astrophysics Data System (ADS)

Zelenyuk, A.; Beranek, J.; Vaden, T.; Imre, D. G.; Zaveri, R. A.

2011-12-01

We present results of measurements conducted by our Single Particle Mass Spectrometer, SPLAT II, in Sacramento, CA over the month of June 2010. SPLAT II measured the size of 195 million particles, and compositions of 10 million particles. In addition to size and composition, SPLAT II simultaneously measured size, density and composition of 121,000 individual particles. These measurements were conducted 2 - 3 times per day, depending on conditions. The data show that throughout the day particles were relatively small (<200 nm), and the vast majority were composed of oxygenated organics mixed with various amounts of sulfate. In addition, we characterized fresh and processed soot, biomass burning aerosol, organic amines, fresh and processed sea salt, and few dust particles. The data show a reproducible diurnal pattern in aerosol size distributions, number concentrations, and compositions. Early in the day, number concentrations were low, particles were very small, and the size distributions peaked at ~70 nm. At this time of the day, 80 nm particles had a density of 1.3 g cm-3; while the density of 200 nm particles was 1.6 g cm-3, consistent with our mass spectra showing that smaller particles were composed of organics mixed with ~10% sulfates, while larger particles were composed mostly of sulfate mixed with a small amount of organics. Later in the day, secondary organic aerosols (SOA) formation led to a number of nucleation events that significantly increased the number concentrations of very small particles. By mid-afternoon, as more SOA formed and condensed, particles increased in size the number concentrations of particles larger than 70 nm increased and the densities of particles 80 to 200 nm particles was ~1.3 g cm-3. The vast majority of these particles were composed of oxygenated organics mixed with a ~10% sulfate. In other words they were SOA particles mixed with a small amount of sulfate. The mass spectra of these particles shows that there were two types of SOA particles, which we labeled Type 43 and Type 44, to indicate which of the two mass-spectral peaks caries higher intensity. We were also able to conduct room temperature evaporation studies of these particles on four separate occasions and found the evaporation kinetics to be reproducible. The data show that after 4 hours of evaporation, in an organic vapor free environment, particles lose only ~20% of their volume. Moreover, evaporation starts with a relatively fast phase and proceeds with a much slower stage about 2 hours after evaporation starts. It is important to keep in mind that these slow evaporating SOA particles were relatively fresh. Based on these studies and similar studies conducted in our laboratory we conclude that these atmospheric SOA particles are quasi-solids. Moreover the data indicate that to first order it is reasonable to approximate SOA particles as being non-volatile. Interestingly, we find that in both SOA particle types a large fraction of the intensity in peaks 44 and 73 was related to a small amount of surface compounds that evaporated within a few minutes.

An experimental study of reactive turbulent mixing

NASA Technical Reports Server (NTRS)

Cooper, L. P.; Marek, C. J.; Strehlow, R. A.

1977-01-01

An experimental study of two coaxial gas streams, which react very rapidly, was performed to investigate the mixing characteristics of turbulent flow fields. The center stream consisted of a CO-N2 mixture and the outer annular stream consisted of air vitiated by H2 combustion. The streams were at equal velocity (50 m/sec) and temperature (1280 K). Turbulence measurements were obtained using hot film anemometry. A sampling probe was used to obtain time averaged gas compositions. Six different turbulence generators were placed in the annular passage to alter the flow field mixing characteristics. The turbulence generators affected the bulk mixing of the streams and the extent of CO conversion to different degrees. The effects can be related to the average eddy size (integral scale) and the bulk mixing. Higher extents of conversion of CO to CO2 were found be increasing the bulk mixing and decreasing the average eddy size.

Modeling the Bergeron-Findeisen Process Using PDF Methods With an Explicit Representation of Mixing

NASA Astrophysics Data System (ADS)

Jeffery, C.; Reisner, J.

2005-12-01

Currently, the accurate prediction of cloud droplet and ice crystal number concentration in cloud resolving, numerical weather prediction and climate models is a formidable challenge. The Bergeron-Findeisen process in which ice crystals grow by vapor deposition at the expense of super-cooled droplets is expected to be inhomogeneous in nature--some droplets will evaporate completely in centimeter-scale filaments of sub-saturated air during turbulent mixing while others remain unchanged [Baker et al., QJRMS, 1980]--and is unresolved at even cloud-resolving scales. Despite the large body of observational evidence in support of the inhomogeneous mixing process affecting cloud droplet number [most recently, Brenguier et al., JAS, 2000], it is poorly understood and has yet to be parameterized and incorporated into a numerical model. In this talk, we investigate the Bergeron-Findeisen process using a new approach based on simulations of the probability density function (PDF) of relative humidity during turbulent mixing. PDF methods offer a key advantage over Eulerian (spatial) models of cloud mixing and evaporation: the low probability (cm-scale) filaments of entrained air are explicitly resolved (in probability space) during the mixing event even though their spatial shape, size and location remain unknown. Our PDF approach reveals the following features of the inhomogeneous mixing process during the isobaric turbulent mixing of two parcels containing super-cooled water and ice, respectively: (1) The scavenging of super-cooled droplets is inhomogeneous in nature; some droplets evaporate completely at early times while others remain unchanged. (2) The degree of total droplet evaporation during the initial mixing period depends linearly on the mixing fractions of the two parcels and logarithmically on Damköhler number (Da)---the ratio of turbulent to evaporative time-scales. (3) Our simulations predict that the PDF of Lagrangian (time-integrated) subsaturation (S) goes as S-1 at high Da. This behavior results from a Gaussian mixing closure and requires observational validation.

Maximum size-density relationships for mixed-hardwood forest stands in New England

Treesearch

Dale S. Solomon; Lianjun Zhang

2000-01-01

Maximum size-density relationships were investigated for two mixed-hardwood ecological types (sugar maple-ash and beech-red maple) in New England. Plots meeting type criteria and undergoing self-thinning were selected for each habitat. Using reduced major axis regression, no differences were found between the two ecological types. Pure species plots (the species basal...

A Torino Scale for Europa and Icy Satellites: A Potential Means for Evaluating the Impact Cratering's Contribution to an Icy Shell's Energy Budget

NASA Astrophysics Data System (ADS)

Bierhaus, E. B.

2017-11-01

Impacts on Europa mix surface and subsurface material, introduce fracturing, and at progressively larger sizes, result in deeper melting (and mixing) within the ice shell. The largest sizes punch through the ice, providing a direct, albeit temporary, conduit between the ocean and the surface.

Fast and economic signal processing technique of laser diode self-mixing interferometry for nanoparticle size measurement

NASA Astrophysics Data System (ADS)

Wang, Huarui; Shen, Jianqi

2014-05-01

The size of nanoparticles is measured by laser diode self-mixing interferometry, which employs a sensitive, compact, and simple optical setup. However, the signal processing of the interferometry is slow or expensive. In this article, a fast and economic signal processing technique is introduced, in which the self-mixing AC signal is transformed into DC signals with an analog circuit consisting of 16 channels. These DC signals are obtained as a spectrum from which the size of nanoparticles can be retrieved. The technique is examined by measuring the standard nanoparticles. Further experiments are performed to compare the skimmed milk and whole milk, and also the fresh skimmed milk and rotten skimmed milk.

Preparation and Electrochemical Characterization of Mesoporous Polyaniline-Silica Nanocomposites as an Electrode Material for Pseudocapacitors

PubMed Central

Zu, Lei; Cui, Xiuguo; Jiang, Yanhua; Hu, Zhongkai; Lian, Huiqin; Liu, Yang; Jin, Yushun; Li, Yan; Wang, Xiaodong

2015-01-01

Mesoporous polyaniline-silica nanocomposites with a full interpenetrating structure for pseudocapacitors were synthesized via the vapor phase approach. The morphology and structure of the nanocomposites were deeply investigated by scanning electron microscopy, infrared spectroscopy, X-ray diffraction, thermal gravimetric analysis and nitrogen adsorption-desorption tests. The results present that the mesoporous nanocomposites possess a uniform particle morphology and full interpenetrating structure, leading to a continuous conductive polyaniline network with a large specific surface area. The electrochemical performances of the nanocomposites were tested in a mixed solution of sulfuric acid and potassium iodide. With the merits of a large specific surface area and suitable pore size distribution, the nanocomposite showed a large specific capacitance (1702.68 farad (F)/g) due to its higher utilization of the active material. This amazing value is almost three-times larger than that of bulk polyaniline when the same mass of active material was used. PMID:28788006

Atmospheric-pressure glow plasma synthesis of plasmonic and photoluminescent zinc oxide nanocrystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilik, N., E-mail: bilik006@umn.edu, E-mail: kortshagen@umn.edu; Greenberg, B. L.; Yang, J.

In this paper, we present a large-volume (non-micro) atmospheric pressure glow plasma capable of rapid, large-scale zinc oxide nanocrystal synthesis and deposition (up to 400 μg/min), whereas in the majority of the literature, nanoparticles are synthesized using micro-scale or filamentary plasmas. The reactor is an RF dielectric barrier discharge with a non-uniform gap spacing. This design encourages pre-ionization during the plasma breakdown, making the discharge uniform over a large volume. The produced zinc oxide nanocrystals typically have diameters ranging from 4 to 15 nm and exhibit photoluminescence at ≈550 nm and localized surface plasmon resonance at ≈1900 cm{sup −1} due to oxygen vacancies. Themore » particle size can be tuned to a degree by varying the gas temperature and the precursor mixing ratio.« less

Neighborhood diversity of large trees shows independent species patterns in a mixed dipterocarp forest in Sri Lanka.

PubMed

Punchi-Manage, Ruwan; Wiegand, Thorsten; Wiegand, Kerstin; Getzin, Stephan; Huth, Andreas; Gunatilleke, C V Savitri; Gunatilleke, I A U Nimal

2015-07-01

Interactions among neighboring individuals influence plant performance and should create spatial patterns in local community structure. In order to assess the role of large trees in generating spatial patterns in local species richness, we used the individual species-area relationship (ISAR) to evaluate the species richness of trees of different size classes (and dead trees) in circular neighborhoods with varying radius around large trees of different focal species. To reveal signals of species interactions, we compared the ISAR function of the individuals of focal species with that of randomly selected nearby locations. We expected that large trees should strongly affect the community structure of smaller trees in their neighborhood, but that these effects should fade away with increasing size class. Unexpectedly, we found that only few focal species showed signals of species interactions with trees of the different size classes and that this was less likely for less abundant focal species. However, the few and relatively weak departures from independence were consistent with expectations of the effect of competition for space and the dispersal syndrome on spatial patterns. A noisy signal of competition for space found for large trees built up gradually with increasing life stage; it was not yet present for large saplings but detectable for intermediates. Additionally, focal species with animal-dispersed seeds showed higher species richness in their neighborhood than those with gravity- and gyration-dispersed seeds. Our analysis across the entire ontogeny from recruits to large trees supports the hypothesis that stochastic effects dilute deterministic species interactions in highly diverse communities. Stochastic dilution is a consequence of the stochastic geometry of biodiversity in species-rich communities where the identities of the nearest neighbors of a given plant are largely unpredictable. While the outcome of local species interactions is governed for each plant by deterministic fitness and niche differences, the large variability of competitors causes also a large variability in the outcomes of interactions and does not allow for strong directed responses at the species level. Collectively, our results highlight the critical effect of the stochastic geometry of biodiversity in structuring local spatial patterns of tropical forest diversity.

Large Marks-decahedral Pd nanoparticles synthesized by a modified hydrothermal method using a homogeneous reactor

NASA Astrophysics Data System (ADS)

Zhao, Haiqiang; Qi, Weihong; Ji, Wenhai; Wang, Tianran; Peng, Hongcheng; Wang, Qi; Jia, Yanlin; He, Jieting

2017-05-01

Fivefold symmetry appears only in small particles and quasicrystals because internal stress in the particles increases with the particle size. However, a typical Marks decahedron with five re-entrant grooves located at the ends of the twin boundaries can further reduce the strain energy. During hydrothermal synthesis, it is difficult to stir the reaction solution contained in a digestion high-pressure tank because of the relatively small size and high-temperature and high-pressure sealed environment. In this work, we optimized a hydrothermal reaction system by replacing the conventional drying oven with a homogeneous reactor to shift the original static reaction solution into a full mixing state. Large Marks-decahedral Pd nanoparticles ( 90 nm) have been successfully synthesized in the optimized hydrothermal synthesis system. Additionally, in the products, round Marks-decahedral Pd particles were also found for the first time. While it remains a challenge to understand the growth mechanism of the fivefold twinned structure, we proposed a plausible growth-mediated mechanism for Marks-decahedral Pd nanoparticles based on observations of the synthesis process.

Effect of charcoal doping on the superconducting properties of MgB 2 bulk

NASA Astrophysics Data System (ADS)

Kim, N. K.; Tan, K. S.; Jun, B.-H.; Park, H. W.; Joo, J.; Kim, C.-J.

2008-09-01

The effect of charcoal doping on the superconducting properties of in situ processed MgB 2 bulk samples was investigated. To understand the size effect of the dopant the charcoal powder was attrition milled for 1 h, 3 h and 6 h using ZrO 2 balls. The milled charcoal powders were mixed with magnesium and boron powders to a nominal composition of Mg(B 0.975C 0.025) 2. The Mg(B 0.975C 0.025) 2 compacts were heat-treated at 900 °C for 0.5 h in flowing Ar atmosphere. Magnetic susceptibility for the samples showed that the superconducting transition temperature ( Tc) decreased as the size of the charcoal powder decreased. The critical current density ( Jc) of Mg(B 0.975C 0.025) 2 prepared using large size charcoal powder was lower than that of the undoped MgB 2. However, a crossover of Jc value was observed at high magnetic fields of about 4 T in Mg(B 0.975C 0.025) 2 prepared using small size charcoal powder. Carbon diffusion into the boron site was easier and gave the Jc increase effect when the small size charcoal was used as a dopant.

Temperature fluctuations inside savanna termite mounds: Do size and plant shade matter?

PubMed

Ndlovu, M; Pérez-Rodríguez, A

2018-05-01

Mound building termites are key ecosystem engineers of subtropical savanna regions. Mounds allow termites to maintain suitable conditions for termite reproduction and food cultivation ('fungus gardens'). We studied how the internal mound temperature of Macrotermes natalensis, a dominant mound-building termite of the subtropical savanna of southern Africa, responds to a number of environmental variables. We used general additive mixed models (GAMM) to determine how external temperature, mound size (volume) and the amount of vegetation shade affects mound internal temperature over a 24-h period. Internal mound temperature varied daily following changes of the external temperature, although the range of variation was much smaller. Active termite mounds maintained a higher internal temperature than inactive ones, and mound activity reinforced the positive effect of mound size and moderated the negative effect of vegetation shade on internal temperatures. In turn, external temperature fluctuations equally affected active and inactive mounds. Large mounds maintained near optimal internal temperatures compared to smaller sized mounds. We therefore conclude that termite mound size is a stronger determinant of internal mound temperature stability compared to plant shade cover. Copyright © 2018 Elsevier Ltd. All rights reserved.

Inter-molecular β-sheet structure facilitates lung-targeting siRNA delivery

NASA Astrophysics Data System (ADS)

Zhou, Jihan; Li, Dong; Wen, Hao; Zheng, Shuquan; Su, Cuicui; Yi, Fan; Wang, Jue; Liang, Zicai; Tang, Tao; Zhou, Demin; Zhang, Li-He; Liang, Dehai; Du, Quan

2016-03-01

Size-dependent passive targeting based on the characteristics of tissues is a basic mechanism of drug delivery. While the nanometer-sized particles are efficiently captured by the liver and spleen, the micron-sized particles are most likely entrapped within the lung owing to its unique capillary structure and physiological features. To exploit this property in lung-targeting siRNA delivery, we designed and studied a multi-domain peptide named K-β, which was able to form inter-molecular β-sheet structures. Results showed that K-β peptides and siRNAs formed stable complex particles of 60 nm when mixed together. A critical property of such particles was that, after being intravenously injected into mice, they further associated into loose and micron-sized aggregates, and thus effectively entrapped within the capillaries of the lung, leading to a passive accumulation and gene-silencing. The large size aggregates can dissociate or break down by the shear stress generated by blood flow, alleviating the pulmonary embolism. Besides the lung, siRNA enrichment and targeted gene silencing were also observed in the liver. This drug delivery strategy, together with the low toxicity, biodegradability, and programmability of peptide carriers, show great potentials in vivo applications.

Factors influencing the choice of a career in food-animal practice among recent graduates and current students of Texas A&M University, College of Veterinary Medicine.

PubMed

Lenarduzzi, Roland; Sheppard, Guy A; Slater, Margaret R

2009-01-01

Concerns about a shortage of large and mixed-animal veterinarians have been discussed in the profession. To better understand veterinary career choices among currently enrolled veterinary students (classes of 2007-2010) and recent graduate veterinarians in Texas (classes of 2002-2006), an online survey was developed. The objectives were to examine: (1) the respondents' backgrounds, demographic data, and experiences; (2) the respondents' working conditions and rural lifestyle considerations; (3) the respondents' perceptions of large/mixed-animal practice; and (4) the factors that have influenced respondents' career choices. The response rate was 37% (390/1,042). Overall, 72% of students and 55% of recent graduates were interested in large/mixed-animal practice. More than 70% of respondents indicated that veterinary practitioners had the strongest personal influence on career choices. Respondents who were no longer interested in large/mixed-animal practice, or who had never been interested, reported no experience with large animals (42% and 64%, respectively) as the most common reason for their lack of interest. Previous and current interest in large/mixed-animal practice were associated with working in a large/mixed-animal practice, any agricultural experience, and working for at least 6 months on a farm or ranch. Any 4-H experience increased the likelihood of previous interest, while being married decreased the likelihood of current interest. Student contact with practitioners (82%) and financial considerations (77%) were most commonly cited as factors that would make a career in large/mixed-animal practice more attractive. Rural lifestyle drawbacks influenced respondents' career choices. Many forms of agricultural experience may expose and encourage students to consider large/mixed-animal practice.

Evidence for a Southern Pattern of Deglacial Surface Warming in the Eastern Equatorial Pacific

NASA Astrophysics Data System (ADS)

Spero, H. J.; Schmidt, M. W.; Lea, D. W.; Lavagnino, L.

2009-12-01

The timing of both Southern and Northern hemisphere warming patterns has been used to explain tropical Pacific warming at the end of the last glacial period. Despite the importance of resolving this deglacial tropical-polar connection, the controversy is still ongoing (Koutavas & Sachs, 2008; Lea et al., 2000, 2006). For instance, the initiation of eastern equatorial Pacific (EEP) surface warming, derived from Mg/Ca analyses of the surface-dwelling foraminifera Globigerinoides ruber, shows a clear correlation with the Southern hemisphere. In contrast, alkenone-derived temperatures from the EEP indicate tropical warming occurred at least 3 kyr later than that implied from Mg/Ca data, thereby suggesting a Northern hemisphere link to initial SST rise. Here, we use a multispecies, multiproxy approach that is based on fundamental foraminifera biology to resolve this controversy. Laboratory experiments demonstrate the final shell size of symbiont-bearing foraminifera varies primarily as a function of the light level (=symbiont photosynthetic rate) that an individual grew under. Because light decreases exponentially in the water column, and the EEP is highly stratified with a shallow mixed layer and cold thermocline, we hypothesize that symbiotic foraminifera with a broad habitat range such as Globigerinoides sacculifer, should produce smaller shells in the more dimly lit cold thermocline than individuals growing in the more illuminated mixed layer. Moreover, these larger shells should contain a temperature signal that is similar to G. ruber, which is constrained to the shallow mixed layer. Mg/Ca and δ18O analyses conducted on 350-400 μm and >650 μm sized G. sacculifer from EEP core TR163-19 (2N, 91W, 2348) demonstrate large specimens yield Mg/Ca and δ18O that are similar to data published previously for mixed layer dwelling G. ruber. In contrast, small G. sacculifer record significantly higher δ18O and lower Mg/Ca temperatures that are consistent with a shallow thermocline habitat. More important, the timing of warming for the large G. sacculifer is similar to that of G. ruber, whereas thermocline temperatures recorded by small G. sacculifer increase nearly 3 kyr later, in close agreement with alkenone temperature change. These results link EEP surface warming to the Southern hemisphere and suggest that 1) early deglacial alkenone data are recording thermocline rather than mixed layer temperatures and 2) EEP thermocline temperature increase is more closely linked to Northern, rather than Southern hemisphere dynamics.

Erythorbic acid promoted formation of CdS QDs in a tube-in-tube micro-channel reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liang, Yan; Tan, Jiawei; Wang, Jiexin

2014-12-15

Erythorbic acid assistant synthesis of CdS quantum dots (QDs) was conducted by homogeneous mixing of two continuous liquids in a high-throughput microporous tube-in-tube micro-channel reactor (MTMCR) at room temperature. The effects of the micropore size of the MTMCR, liquid flow rate, mixing time and reactant concentration on the size and size distribution of CdS QDs were investigated. It was found that the size and size distribution of CdS QDs could be tuned in the MTMCR. A combination of erythorbic acid promoted formation technique with the MTMCR may be a promising pathway for controllable mass production of QDs.

Geologic map of the Sunnymead 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Matti, Jonathan C.

2001-01-01

a. This Readme; includes in Appendix I, data contained in sun_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Electrical and Thermal Transport in Coplanar Polycrystalline Graphene-hBN Heterostructures.

PubMed

Barrios-Vargas, José Eduardo; Mortazavi, Bohayra; Cummings, Aron W; Martinez-Gordillo, Rafael; Pruneda, Miguel; Colombo, Luciano; Rabczuk, Timon; Roche, Stephan

2017-03-08

We present a theoretical study of electronic and thermal transport in polycrystalline heterostructures combining graphene (G) and hexagonal boron nitride (hBN) grains of varying size and distribution. By increasing the hBN grain density from a few percent to 100%, the system evolves from a good conductor to an insulator, with the mobility dropping by orders of magnitude and the sheet resistance reaching the MΩ regime. The Seebeck coefficient is suppressed above 40% mixing, while the thermal conductivity of polycrystalline hBN is found to be on the order of 30-120 Wm -1 K -1 . These results, agreeing with available experimental data, provide guidelines for tuning G-hBN properties in the context of two-dimensional materials engineering. In particular, while we proved that both electrical and thermal properties are largely affected by morphological features (e.g., by the grain size and composition), we find in all cases that nanometer-sized polycrystalline G-hBN heterostructures are not good thermoelectric materials.

Urban particle size distributions during two contrasting dust events originating from Taklimakan and Gobi Deserts.

PubMed

Zhao, Suping; Yu, Ye; Xia, Dunsheng; Yin, Daiying; He, Jianjun; Liu, Na; Li, Fang

2015-12-01

The dust origins of the two events were identified using HYSPLIT trajectory model and MODIS and CALIPSO satellite data to understand the particle size distribution during two contrasting dust events originated from Taklimakan and Gobi deserts. The supermicron particles significantly increased during the dust events. The dust event from Gobi desert affected significantly on the particles larger than 2.5 μm, while that from Taklimakan desert impacted obviously on the particles in 1.0-2.5 μm. It is found that the particle size distributions and their modal parameters such as VMD (volume median diameter) have significant difference for varying dust origins. The dust from Taklimakan desert was finer than that from Gobi desert also probably due to other influencing factors such as mixing between dust and urban emissions. Our findings illustrated the capacity of combining in situ, satellite data and trajectory model to characterize large-scale dust plumes with a variety of aerosol parameters. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mesoscale spatiotemporal variability in a complex host-parasite system influenced by intermediate host body size

PubMed Central

2017-01-01

Background Parasites are essential components of natural communities, but the factors that generate skewed distributions of parasite occurrences and abundances across host populations are not well understood. Methods Here, we analyse at a seascape scale the spatiotemporal relationships of parasite exposure and host body-size with the proportion of infected hosts (i.e., prevalence) and aggregation of parasite burden across ca. 150 km of the coast and over 22 months. We predicted that the effects of parasite exposure on prevalence and aggregation are dependent on host body-sizes. We used an indirect host-parasite interaction in which migratory seagulls, sandy-shore molecrabs, and an acanthocephalan worm constitute the definitive hosts, intermediate hosts, and endoparasite, respectively. In such complex systems, increments in the abundance of definitive hosts imply increments in intermediate hosts’ exposure to the parasite’s dispersive stages. Results Linear mixed-effects models showed a significant, albeit highly variable, positive relationship between seagull density and prevalence. This relationship was stronger for small (cephalothorax length >15 mm) than large molecrabs (<15 mm). Independently of seagull density, large molecrabs carried significantly more parasites than small molecrabs. The analysis of the variance-to-mean ratio of per capita parasite burden showed no relationship between seagull density and mean parasite aggregation across host populations. However, the amount of unexplained variability in aggregation was strikingly higher in larger than smaller intermediate hosts. This unexplained variability was driven by a decrease in the mean-variance scaling in heavily infected large molecrabs. Conclusions These results show complex interdependencies between extrinsic and intrinsic population attributes on the structure of host-parasite interactions. We suggest that parasite accumulation—a characteristic of indirect host-parasite interactions—and subsequent increasing mortality rates over ontogeny underpin size-dependent host-parasite dynamics. PMID:28828270

Mesoscale spatiotemporal variability in a complex host-parasite system influenced by intermediate host body size.

PubMed

Rodríguez, Sara M; Valdivia, Nelson

2017-01-01

Parasites are essential components of natural communities, but the factors that generate skewed distributions of parasite occurrences and abundances across host populations are not well understood. Here, we analyse at a seascape scale the spatiotemporal relationships of parasite exposure and host body-size with the proportion of infected hosts (i.e., prevalence) and aggregation of parasite burden across ca. 150 km of the coast and over 22 months. We predicted that the effects of parasite exposure on prevalence and aggregation are dependent on host body-sizes. We used an indirect host-parasite interaction in which migratory seagulls, sandy-shore molecrabs, and an acanthocephalan worm constitute the definitive hosts, intermediate hosts, and endoparasite, respectively. In such complex systems, increments in the abundance of definitive hosts imply increments in intermediate hosts' exposure to the parasite's dispersive stages. Linear mixed-effects models showed a significant, albeit highly variable, positive relationship between seagull density and prevalence. This relationship was stronger for small (cephalothorax length >15 mm) than large molecrabs (<15 mm). Independently of seagull density, large molecrabs carried significantly more parasites than small molecrabs. The analysis of the variance-to-mean ratio of per capita parasite burden showed no relationship between seagull density and mean parasite aggregation across host populations. However, the amount of unexplained variability in aggregation was strikingly higher in larger than smaller intermediate hosts. This unexplained variability was driven by a decrease in the mean-variance scaling in heavily infected large molecrabs. These results show complex interdependencies between extrinsic and intrinsic population attributes on the structure of host-parasite interactions. We suggest that parasite accumulation-a characteristic of indirect host-parasite interactions-and subsequent increasing mortality rates over ontogeny underpin size-dependent host-parasite dynamics.

Foundational Principles for Large-Scale Inference: Illustrations Through Correlation Mining.

PubMed

Hero, Alfred O; Rajaratnam, Bala

2016-01-01

When can reliable inference be drawn in fue "Big Data" context? This paper presents a framework for answering this fundamental question in the context of correlation mining, wifu implications for general large scale inference. In large scale data applications like genomics, connectomics, and eco-informatics fue dataset is often variable-rich but sample-starved: a regime where the number n of acquired samples (statistical replicates) is far fewer than fue number p of observed variables (genes, neurons, voxels, or chemical constituents). Much of recent work has focused on understanding the computational complexity of proposed methods for "Big Data". Sample complexity however has received relatively less attention, especially in the setting when the sample size n is fixed, and the dimension p grows without bound. To address fuis gap, we develop a unified statistical framework that explicitly quantifies the sample complexity of various inferential tasks. Sampling regimes can be divided into several categories: 1) the classical asymptotic regime where fue variable dimension is fixed and fue sample size goes to infinity; 2) the mixed asymptotic regime where both variable dimension and sample size go to infinity at comparable rates; 3) the purely high dimensional asymptotic regime where the variable dimension goes to infinity and the sample size is fixed. Each regime has its niche but only the latter regime applies to exa cale data dimension. We illustrate this high dimensional framework for the problem of correlation mining, where it is the matrix of pairwise and partial correlations among the variables fua t are of interest. Correlation mining arises in numerous applications and subsumes the regression context as a special case. we demonstrate various regimes of correlation mining based on the unifying perspective of high dimensional learning rates and sample complexity for different structured covariance models and different inference tasks.

Mixing state of ambient aerosols during different fog-haze pollution episodes in the Yangtze River Delta, China

NASA Astrophysics Data System (ADS)

Hu, Rui; Wang, Honglei; Yin, Yan; Chen, Kui; Zhu, Bin; Zhang, Zefeng; Kang, Hui; Shen, Lijuan

2018-04-01

The mixing state of aerosol particles were investigated using a single particle aerosol mass spectrometer (SPAMS) during a regional fog-haze episode in the Yangtze River Delta (YRD) on 16-28 Dec., 2015. The aerosols were analyzed and clustered into 12 classes: aged elemental carbon (Aged-EC), internally mixed organics and elemental carbon (ECOC), organic carbon (OC), Biomass, Amine, Ammonium, Na-K, V-rich, Pb-rich, Cu-rich, Fe-rich and Dust. Results showed that particles in short-term rainfalls mixed with more nitrate and oxidized organics, while they mixed with more ammonium and sulfate in long-term rainfall. Due to anthropogenic activities, stronger winds and solar radiation, the particle counts increased and the size ranges of particles broadened in haze. Carbonaceous particles and Na-K mixed with enhanced secondary species during haze, and obviously were more acidic, especially for the ones with a size range of 0.6-1.2 μm. For local and long-range transported pollution, OC had distinct size distributions while the changes of ECOC were uniform. The secondary formation of ECOC contributed significantly in local pollution and affected much smaller particles (as small as 0.5 μm) in long-range transported pollution. And long-range transported pollution was more helpful for the growth of OC. Particles mixed with more chloride and nitrate/sulfate in local/long-range transported pollution.

Life history and past demography maintain genetic structure, outcrossing rate, contemporary pollen gene flow of an understory herb in a highly fragmented rainforest

PubMed Central

Suárez-Montes, Pilar; Chávez-Pesqueira, Mariana

2016-01-01

Introduction Theory predicts that habitat fragmentation, by reducing population size and increasing isolation among remnant populations, can alter their genetic diversity and structure. A cascade of effects is expected: genetic drift and inbreeding after a population bottleneck, changes in biotic interactions that may affect, as in the case of plants, pollen dynamics, mating system, reproductive success. The detection of the effects of contemporary habitat fragmentation on the genetic structure of populations are conditioned by the magnitude of change, given the few number of generations since the onset of fragmentation, especially for long-lived organisms. However, the present-day genetic structure of populations may bear the signature of past demography events. Here, we examine the effects of rainforest fragmentation on the genetic diversity, population structure, mating system (outcrossing rate), indirect gene flow and contemporary pollen dynamics in the understory herb Aphelandra aurantiaca. Also, we assessed its present-day genetic structure under different past demographic scenarios. Methods Twelve populations of A. aurantiaca were sampled in large (4), medium (3), and small (5) forest fragments in the lowland tropical rainforest at Los Tuxtlas region. Variation at 11 microsatellite loci was assessed in 28–30 reproductive plants per population. In two medium- and two large-size fragments we estimated the density of reproductive plants, and the mating system by analyzing the progeny of different mother plants per population. Results Despite prevailing habitat fragmentation, populations of A. aurantiaca possess high genetic variation (He = 0.61), weak genetic structure (Rst = 0.037), and slight inbreeding in small fragments. Effective population sizes (Ne) were large, but slightly lower in small fragments. Migrants derive mostly from large and medium size fragments. Gene dispersal is highly restricted but long distance gene dispersal events were detected. Aphelandra aurantiaca shows a mixed mating system (tm = 0.81) and the outcrossing rate have not been affected by habitat fragmentation. A strong pollen pool structure was detected due to few effective pollen donors (Nep) and low distance pollen movement, pointing that most plants received pollen from close neighbors. Past demographic fluctuations may have affected the present population genetic structure as Bayesian coalescent analysis revealed the signature of past population expansion, possibly during warmer conditions after the last glacial maximum. Discussion Habitat fragmentation has not increased genetic differentiation or reduced genetic diversity of A. aurantiaca despite dozens of generations since the onset of fragmentation in the region of Los Tuxtlas. Instead, past population expansion is compatible with the lack of observed genetic structure. The predicted negative effects of rainforest fragmentation on genetic diversity and population structure of A. aurantiaca seem to have been buffered owing to its large effective populations and long-distance dispersal events. In particular, its mixed-mating system, mostly of outcrossing, suggests high efficiency of pollinators promoting connectivity and reducing inbreeding. However, some results point that the effects of fragmentation are underway, as two small fragments showed higher membership probabilities to their population of origin, suggesting genetic isolation. Our findings underscore the importance of fragment size to maintain genetic connectivity across the landscape. PMID:28028460

Coagulation of highly turbid suspensions using magnesium hydroxide: effects of slow mixing conditions.

PubMed

Ayoub, George M; BinAhmed, Sara W; Al-Hindi, Mahmoud; Azizi, Fouad

2014-09-01

Laboratory experiments were carried out to study the effects of slow mixing conditions on magnesium hydroxide floc size and strength and to determine the turbidity and total suspended solid (TSS) removal efficiencies during coagulation of highly turbid suspensions. A highly turbid kaolin clay suspension (1,213 ± 36 nephelometric turbidity units (NTU)) was alkalized to pH 10.5 using a 5 M NaOH solution; liquid bittern (LB) equivalent to 536 mg/L of Mg(2+) was added as a coagulant, and the suspension was then subjected to previously optimized fast mixing conditions of 100 rpm and 60 s. Slow mixing speed (20, 30, 40, and 50 rpm) and time (10, 20, and 30 min) were then varied, while the temperature was maintained at 20.7 ± 1 °C. The standard practice for coagulation-flocculation jar test ASTM D2035-13 (2013) was followed in all experiments. Relative floc size was monitored using an optical measuring device, photometric dispersion analyzer (PDA 2000). Larger and more shear resistant flocs were obtained at 20 rpm for both 20- and 30-min slow mixing times; however, given the shorter duration for the former, the 20-min slow mixing time was considered to be more energy efficient. For slow mixing camp number (Gt) values in the range of 8,400-90,000, it was found that the mixing speed affected floc size and strength more than the time. Higher-turbidity removal efficiencies were achieved at 20 and 30 rpm, while TSS removal efficiency was higher for the 50-rpm slow mixing speed. Extended slow mixing time of 30 min yielded better turbidity and TSS removal efficiencies at the slower speeds.

Assessing map accuracy in a remotely sensed, ecoregion-scale cover map

USGS Publications Warehouse

Edwards, T.C.; Moisen, Gretchen G.; Cutler, D.R.

1998-01-01

Landscape- and ecoregion-based conservation efforts increasingly use a spatial component to organize data for analysis and interpretation. A challenge particular to remotely sensed cover maps generated from these efforts is how best to assess the accuracy of the cover maps, especially when they can exceed 1000 s/km2 in size. Here we develop and describe a methodological approach for assessing the accuracy of large-area cover maps, using as a test case the 21.9 million ha cover map developed for Utah Gap Analysis. As part of our design process, we first reviewed the effect of intracluster correlation and a simple cost function on the relative efficiency of cluster sample designs to simple random designs. Our design ultimately combined clustered and subsampled field data stratified by ecological modeling unit and accessibility (hereafter a mixed design). We next outline estimation formulas for simple map accuracy measures under our mixed design and report results for eight major cover types and the three ecoregions mapped as part of the Utah Gap Analysis. Overall accuracy of the map was 83.2% (SE=1.4). Within ecoregions, accuracy ranged from 78.9% to 85.0%. Accuracy by cover type varied, ranging from a low of 50.4% for barren to a high of 90.6% for man modified. In addition, we examined gains in efficiency of our mixed design compared with a simple random sample approach. In regard to precision, our mixed design was more precise than a simple random design, given fixed sample costs. We close with a discussion of the logistical constraints facing attempts to assess the accuracy of large-area, remotely sensed cover maps.

Large-Scale Mixed Temperate Forest Mapping at the Single Tree Level using Airborne Laser Scanning

NASA Astrophysics Data System (ADS)

Scholl, V.; Morsdorf, F.; Ginzler, C.; Schaepman, M. E.

2017-12-01

Monitoring vegetation on a single tree level is critical to understand and model a variety of processes, functions, and changes in forest systems. Remote sensing technologies are increasingly utilized to complement and upscale the field-based measurements of forest inventories. Airborne laser scanning (ALS) systems provide valuable information in the vertical dimension for effective vegetation structure mapping. Although many algorithms exist to extract single tree segments from forest scans, they are often tuned to perform well in homogeneous coniferous or deciduous areas and are not successful in mixed forests. Other methods are too computationally expensive to apply operationally. The aim of this study was to develop a single tree detection workflow using leaf-off ALS data for the canton of Aargau in Switzerland. Aargau covers an area of over 1,400km2 and features mixed forests with various development stages and topography. Forest type was classified using random forests to guide local parameter selection. Canopy height model-based treetop maxima were detected and maintained based on the relationship between tree height and window size, used as a proxy to crown diameter. Watershed segmentation was used to generate crown polygons surrounding each maximum. The location, height, and crown dimensions of single trees were derived from the ALS returns within each polygon. Validation was performed through comparison with field measurements and extrapolated estimates from long-term monitoring plots of the Swiss National Forest Inventory within the framework of the Swiss Federal Institute for Forest, Snow, and Landscape Research. This method shows promise for robust, large-scale single tree detection in mixed forests. The single tree data will aid ecological studies as well as forest management practices. Figure description: Height-normalized ALS point cloud data (top) and resulting single tree segments (bottom) on the Laegeren mountain in Switzerland.

Impact of Snow Grain Shape and Internal Mixing with Black Carbon Aerosol on Snow Optical Properties for use in Climate Models

NASA Astrophysics Data System (ADS)

He, C.; Liou, K. N.; Takano, Y.; Yang, P.; Li, Q.; Chen, F.

2017-12-01

A set of parameterizations is developed for spectral single-scattering properties of clean and black carbon (BC)-contaminated snow based on geometric-optic surface-wave (GOS) computations, which explicitly resolves BC-snow internal mixing and various snow grain shapes. GOS calculations show that, compared with nonspherical grains, volume-equivalent snow spheres show up to 20% larger asymmetry factors and hence stronger forward scattering, particularly at wavelengths <1 mm. In contrast, snow grain sizes have a rather small impact on the asymmetry factor at wavelengths <1 mm, whereas size effects are important at longer wavelengths. The snow asymmetry factor is parameterized as a function of effective size, aspect ratio, and shape factor, and shows excellent agreement with GOS calculations. According to GOS calculations, the single-scattering coalbedo of pure snow is predominantly affected by grain sizes, rather than grain shapes, with higher values for larger grains. The snow single-scattering coalbedo is parameterized in terms of the effective size that combines shape and size effects, with an accuracy of >99%. Based on GOS calculations, BC-snow internal mixing enhances the snow single-scattering coalbedo at wavelengths <1 mm, but it does not alter the snow asymmetry factor. The BC-induced enhancement ratio of snow single-scattering coalbedo, independent of snow grain size and shape, is parameterized as a function of BC concentration with an accuracy of >99%. Overall, in addition to snow grain size, both BC-snow internal mixing and snow grain shape play critical roles in quantifying BC effects on snow optical properties. The present parameterizations can be conveniently applied to snow, land surface, and climate models including snowpack radiative transfer processes.

Evolution of the properties of Al(n)N(n) clusters with size.

PubMed

Costales, Aurora; Blanco, M A; Francisco, E; Pandey, Ravindra; Martín Pendás, A

2005-12-29

A global optimization of stoichiometric (AlN)(n) clusters (n = 1-25, 30, 35, ..., 95, 100) has been performed using the basin-hopping (BH) method and describing the interactions with simple and yet realistic interatomic potentials. The results for the smaller isomers agree with those of previous electronic structure calculations, thus validating the present scheme. The lowest-energy isomers found can be classified in three different categories according to their structural motifs: (i) small clusters (n = 2-5), with planar ring structures and 2-fold coordination, (ii) medium clusters (n = 6-40), where a competition between stacked rings and globular-like empty cages exists, and (iii) large clusters (n > 40), large enough to mix different elements of the previous stage. All the atoms in small and medium-sized clusters are in the surface, while large clusters start to display interior atoms. Large clusters display a competition between tetrahedral and octahedral-like features: the former lead to a lower energy interior in the cluster, while the latter allow for surface terminations with a lower energy. All of the properties studied present different regimes according to the above classification. It is of particular interest that the local properties of the interior atoms do converge to the bulk limit. The isomers with n = 6 and 12 are specially stable with respect to the gain or loss of AlN molecules.

Effect of the Initial Vortex Size on Intensity Change in the WRF-ROMS Coupled Model

NASA Astrophysics Data System (ADS)

Zhao, Xiaohui; Chan, Johnny C. L.

2017-12-01

Numerous studies have demonstrated that the tropical cyclone (TC) induced sea surface temperature (SST) cooling strongly depends on the preexisting oceanic condition and TC characteristics. However, very few focused on the correlation of SST cooling and the subsequent intensity with TC size. Therefore, a series of idealized numerical experiments are conducted using the Weather Research Forecasting (WRF) model coupled with the Regional Ocean Model System (ROMS) model to understand how the vortex size is related to SST cooling and subsequent intensity changes of a stationary TC-like vortex. In the uncoupled experiments, the radius of maximum wind (RMW) and size (radius of gale-force wind (R17)) both depend on the initial size within the 72 h simulation. The initially small vortex is smaller than the medium and large vortices throughout its life cycle and is the weakest. In other words, thermodynamic processes do not contribute as much to the R17 change as the dynamic processes proposed (e.g., angular momentum transport) in previous studies. In the coupled experiments, the area-averaged SST cooling induced by medium and large TCs within the inner-core region is comparable due to the similar surface winds and thus mixing in the ocean. Although a stronger SST cooling averaged within a larger region outside the inner-core is induced by the larger TC, the intensity of the larger TC is more intense. This is because that the enthalpy flux in the inner-core region is higher in the larger TC than that in the medium and small TCs.

Chemical consequences of the initial diffusional growth of cloud droplets - A clean marine case

NASA Technical Reports Server (NTRS)

Twohy, C. H.; Charlson, R. J.; Austin, P. H.

1989-01-01

A simple microphysical cloud parcel model and a simple representation of the background marine aerosol are used to predict the concentrations and compositions of droplets of various sizes near cloud base. The aerosol consists of an externally-mixed ammonium bisulfate accumulation mode and a sea-salt coarse particle mode. The difference in diffusional growth rates between the small and large droplets as well as the differences in composition between the two aerosol modes result in substantial differences in solute concentration and composition with size of droplets in the parcel. The chemistry of individual droplets is not, in general, representative of the bulk (volume-weighted mean) cloud water sample. These differences, calculated to occur early in the parcel's lifetime, should have important consequences for chemical reactions such as aqueous phase sulfate production.

The PIG in sPrInG: evidence on letter grouping from the reading of buried words.

PubMed

Humphreys, Glyn W; Mayall, Kate; Cooper, Adam C G

2003-12-01

We introduce a novel procedure for investigating factors that determine selective attention to letters in words. Participants were presented with words (in Experiments 1 and 3) and nonwords (in Experiment 2) that contained a buried word whose letters differed in color relative to the other letters present (e.g., pig, in spring). The strings were presented in single case or mixed case, keeping the letters of the buried words in one case (SpRiNg). The time in which the whole stimulus was named was shorter for same-case than for mixed-case strings (for spring: spring < SpRiNg). In contrast, the time in which buried words were named was shorter in mixed- than in same-case strings (for pig: spring > SpRiNg). Across items, the effects of case mixing were negatively correlated across the two tasks. The positive effect of case mixing for buried words also occurred irrespective of whether the whole string was a word or a nonword, and there were contributions from similarity of both letter size and case. The results suggest that case mixing can facilitate selective attention to letters, which is otherwise disrupted by size- and case-based grouping across letter strings. The study provides evidence for letter grouping using size and case information.

Vocal Music Therapy for Chronic Pain Management in Inner City African Americans: A Mixed Methods Feasibility Study

PubMed Central

Bradt, Joke; Norris, Marisol; Shim, Minjung; Gracely, Edward J.; Gerrity, Patricia

2017-01-01

Background To date, research on music for pain management has focused primarily on listening to pre-recorded music for acute pain. Research is needed on the impact of active music therapy interventions on chronic pain management. Objective The aim of this mixed methods research study was to determine feasibility and estimates of effect of vocal music therapy for chronic pain management. Methods Fifty-five inner city adults, predominantly African-Americans, with chronic pain were randomized to an 8-week vocal music therapy treatment group or waitlist control group. Consent and attrition rates, treatment compliance, and instrument appropriateness/burden were tracked. Physical functioning (pain interference and general activities), self-efficacy, emotional functioning, pain intensity, pain coping, and participant perception of change were measured at baseline, 4, 8, and 12 weeks. Focus groups were conducted at the 12-week follow-up. Results The consent rate was 77%. The attrition rate was 27% at follow-up. We established acceptability of the intervention. Large effect sizes were obtained for self-efficacy at weeks 8 and 12; a moderate effect size was found for pain interference at week 8; no improvements were found for general activities and emotional functioning. Moderate effect sizes were obtained for pain intensity and small effect sizes for coping, albeit not statistically significant. Qualitative findings suggested that the treatment resulted in enhanced self-management, motivation, empowerment, a sense of belonging, and reduced isolation. Conclusions This study suggests that vocal music therapy may be effective in building essential stepping stones for effective chronic pain management namely enhanced self-efficacy, motivation, empowerment, and social engagement. PMID:27090149

Vocal Music Therapy for Chronic Pain Management in Inner-City African Americans: A Mixed Methods Feasibility Study.

PubMed

Bradt, Joke; Norris, Marisol; Shim, Minjung; Gracely, Edward J; Gerrity, Patricia

2016-01-01

To date, research on music for pain management has focused primarily on listening to prerecorded music for acute pain. Research is needed on the impact of active music therapy interventions on chronic pain management. The aim of this mixed methods research study was to determine feasibility and estimates of effect of vocal music therapy for chronic pain management. Fifty-five inner-city adults, predominantly African Americans, with chronic pain were randomized to an 8-week vocal music therapy treatment group or waitlist control group. Consent and attrition rates, treatment compliance, and instrument appropriateness/burden were tracked. Physical functioning (pain interference and general activities), self-efficacy, emotional functioning, pain intensity, pain coping, and participant perception of change were measured at baseline, 4, 8, and 12 weeks. Focus groups were conducted at the 12-week follow-up. The consent rate was 77%. The attrition rate was 27% at follow-up. We established acceptability of the intervention. Large effect sizes were obtained for self-efficacy at weeks 8 and 12; a moderate effect size was found for pain interference at week 8; no improvements were found for general activities and emotional functioning. Moderate effect sizes were obtained for pain intensity and small effect sizes for coping, albeit not statistically significant. Qualitative findings suggested that the treatment resulted in enhanced self-management, motivation, empowerment, a sense of belonging, and reduced isolation. This study suggests that vocal music therapy may be effective in building essential stepping-stones for effective chronic pain management, namely enhanced self-efficacy, motivation, empowerment, and social engagement. © the American Music Therapy Association 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Water temperature and fish growth: otoliths predict growth patterns of a marine fish in a changing climate.

PubMed

Rountrey, Adam N; Coulson, Peter G; Meeuwig, Jessica J; Meekan, Mark

2014-08-01

Ecological modeling shows that even small, gradual changes in body size in a fish population can have large effects on natural mortality, biomass, and catch. However, efforts to model the impact of climate change on fish growth have been hampered by a lack of long-term (multidecadal) data needed to understand the effects of temperature on growth rates in natural environments. We used a combination of dendrochronology techniques and additive mixed-effects modeling to examine the sensitivity of growth in a long-lived (up to 70 years), endemic marine fish, the western blue groper (Achoerodus gouldii), to changes in water temperature. A multi-decadal biochronology (1952-2003) of growth was constructed from the otoliths of 56 fish collected off the southwestern coast of Western Australia, and we tested for correlations between the mean index chronology and a range of potential environmental drivers. The chronology was significantly correlated with sea surface temperature in the region, but common variance among individuals was low. This suggests that this species has been relatively insensitive to past variations in climate. Growth increment and age data were also used in an additive mixed model to predict otolith growth and body size later this century. Although growth was relatively insensitive to changes in temperature, the model results suggested that a fish aged 20 in 2099 would have an otolith about 10% larger and a body size about 5% larger than a fish aged 20 in 1977. Our study shows that species or populations regarded as relatively insensitive to climate change could still undergo significant changes in growth rate and body size that are likely to have important effects on the productivity and yield of fisheries. © 2014 John Wiley & Sons Ltd.

Well-ordered large-area arrays of epitaxial ferroelectric (Bi,La)4Ti3O12 nanostructures fabricated by gold nanotube-membrane lithography

NASA Astrophysics Data System (ADS)

Lee, Sung Kyun; Lee, Woo; Alexe, Marin; Nielsch, Kornelius; Hesse, Dietrich; Gösele, Ulrich

2005-04-01

Two-dimensionally well-ordered, large-area arrays of epitaxial, ferroelectric, La-substituted Bi4Ti3O12 (BLT) nanostructures are prepared using gold nanotube membranes as a liftoff mask. Epitaxial nanostructures with a height of about 65nm and a lateral size of about 150nm, with either (001) ("c-axis") orientation, or mixed (118)/(100) ("non-c-axis") orientation, are obtained on (001)- and (011)-oriented SrTiO3 substrates, respectively. The ferroelectric properties are probed by piezoresponse scanning force microscopy. Non-c-axis-oriented BLT nanostructures show an effective piezoresponse coefficient (2dzz) of about 38.0pm /V, whereas c-axis-oriented structures show one of only about 4.9pm/V.

Validating the MFiX-DEM Model for Flow Regime Prediction in a 3D Spouted Bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Banerjee, Subhodeep; Guenther, Chris; Rogers, William A.

The spout-fluidized bed reactor with relatively large oxygen carrier particles offers several advantages in chemical looping combustion operation using solid fuels. The large difference in size and weight between the oxygen carrier particles and the smaller coal or ash particles allows the oxygen carrier to be easily segregated for recirculation; the increased solids mixing due to dynamic flow pattern in the spout-fluidization regime prevents agglomeration. The primary objective in this work is to determine the effectiveness of the MFiX-DEM model in predicting the flow regime in a spouted bed. Successful validation of the code will allow the user to finemore » tune the operating conditions of a spouted bed to achieve the desired operating condition.« less

Sample Size Estimation for Alzheimer's Disease Trials from Japanese ADNI Serial Magnetic Resonance Imaging.

PubMed

Fujishima, Motonobu; Kawaguchi, Atsushi; Maikusa, Norihide; Kuwano, Ryozo; Iwatsubo, Takeshi; Matsuda, Hiroshi

2017-01-01

Little is known about the sample sizes required for clinical trials of Alzheimer's disease (AD)-modifying treatments using atrophy measures from serial brain magnetic resonance imaging (MRI) in the Japanese population. The primary objective of the present study was to estimate how large a sample size would be needed for future clinical trials for AD-modifying treatments in Japan using atrophy measures of the brain as a surrogate biomarker. Sample sizes were estimated from the rates of change of the whole brain and hippocampus by the k-means normalized boundary shift integral (KN-BSI) and cognitive measures using the data of 537 Japanese Alzheimer's Neuroimaging Initiative (J-ADNI) participants with a linear mixed-effects model. We also examined the potential use of ApoE status as a trial enrichment strategy. The hippocampal atrophy rate required smaller sample sizes than cognitive measures of AD and mild cognitive impairment (MCI). Inclusion of ApoE status reduced sample sizes for AD and MCI patients in the atrophy measures. These results show the potential use of longitudinal hippocampal atrophy measurement using automated image analysis as a progression biomarker and ApoE status as a trial enrichment strategy in a clinical trial of AD-modifying treatment in Japanese people.

Dimension yields from short logs of low-quality hardwood trees.

Treesearch

Howard N. Rosen; Harold A. Stewart; David J. Polak

1980-01-01

Charts are presented for determining yields of 4/4 dimension cuttings from short hardwood logs of aspen, soft maple, black cherry, yellow-poplar, and black walnut for several cutting grades and bolt sizes. Cost comparisons of short log and standard grade mixes show sizes. Cost comparisons of short log and standard grade mixes show the estimated least expensive...

Maximum size-density relationships for mixed softwoods in the northeastern USA

Treesearch

Dale S. Solomon; Lianjun Zhang

2002-01-01

The maximum size-density relationships or self-thinning lines were developed for three mix .ed-softwood climax forest habitats (hemlock-red spruce, spruce-fir, and cedar-black spruce) in the northeastern USA. The plot data were collected from an extensive data base used in growth studies from 1950 to 1970, and represented a wide range of species compositions, sites,...

Casein polymorphism heterogeneity influences casein micelle size in milk of individual cows.

PubMed

Day, L; Williams, R P W; Otter, D; Augustin, M A

2015-06-01

Milk samples from individual cows producing small (148-155 nm) or large (177-222 nm) casein micelles were selected to investigate the relationship between the individual casein proteins, specifically κ- and β-casein phenotypes, and casein micelle size. Only κ-casein AA and β-casein A1A1, A1A2 and A2A2 phenotypes were found in the large casein micelle group. Among the small micelle group, both κ-casein and β-casein phenotypes were more diverse. κ-Casein AB was the dominant phenotype, and 3 combinations (AA, AB, and BB) were present in the small casein micelle group. A considerable mix of β-casein phenotypes was found, including B and I variants, which were only found in the small casein micelle group. The relative amount of κ-casein to total casein was significantly higher in the small micelle group, and the nonglycosylated and glycosylated κ-casein contents were higher in the milks with small casein micelles (primarily with κ-casein AB and BB variants) compared with the large micelle group. The ratio of glycosylated to nonglycosylated κ-casein was higher in the milks with small casein micelles compared with the milks with large casein micelles. This suggests that although the amount of κ-casein (both glycosylated and nonglycosylated) is associated with micelle size, an increased proportion of glycosylated κ-casein could be a more important and favorable factor for small micelle size. This suggests that the increased spatial requirement due to addition of the glycosyl group with increasing extent of glycosylation of κ-casein is one mechanism that controls casein micelle assembly and growth. In addition, increased electrostatic repulsion due to the sialyl residues on the glycosyl group could be a contributory factor. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Mapping and exploring variation in post-fire vegetation recovery following mixed severity wildfire using airborne LiDAR.

PubMed

Gordon, Christopher E; Price, Owen F; Tasker, Elizabeth M

2017-07-01

There is a public perception that large high-severity wildfires decrease biodiversity and increase fire hazard by homogenizing vegetation composition and increasing the cover of mid-story vegetation. But a growing literature suggests that vegetation responses are nuanced. LiDAR technology provides a promising remote sensing tool to test hypotheses about post-fire vegetation regrowth because vegetation cover can be quantified within different height strata at fine scales over large areas. We assess the usefulness of airborne LiDAR data for measuring post-fire mid-story vegetation regrowth over a range of spatial resolutions (10 × 10 m, 30 × 30 m, 50 × 50 m, 100 × 100 m cell size) and investigate the effect of fire severity on regrowth amount and spatial pattern following a mixed severity wildfire in Warrumbungle National Park, Australia. We predicted that recovery would be more vigorous in areas of high fire severity, because park managers observed dense post-fire regrowth in these areas. Moderate to strong positive associations were observed between LiDAR and field surveys of mid-story vegetation cover between 0.5-3.0 m. Thus our LiDAR survey was an apt representation of on-ground vegetation cover. LiDAR-derived mid-story vegetation cover was 22-40% lower in areas of low and moderate than high fire severity. Linear mixed-effects models showed that fire severity was among the strongest biophysical predictors of mid-story vegetation cover irrespective of spatial resolution. However much of the variance associated with these models was unexplained, presumably because soil seed banks varied at finer scales than our LiDAR maps. Dense patches of mid-story vegetation regrowth were small (median size 0.01 ha) and evenly distributed between areas of low, moderate and high fire severity, demonstrating that high-severity fires do not homogenize vegetation cover. Our results are relevant for ecosystem conservation and fire management because they: indicate that native vegetation are responsive and resilient to high-severity fire, and show the usefulness of remote sensing tools such as LiDAR to monitor post-fire vegetation recovery over large areas in situ. © 2017 by the Ecological Society of America.

Design and methodology of a mixed methods follow-up study to the 2014 Ghana Demographic and Health Survey.

PubMed

Staveteig, Sarah; Aryeetey, Richmond; Anie-Ansah, Michael; Ahiadeke, Clement; Ortiz, Ladys

2017-01-01

The intended meaning behind responses to standard questions posed in large-scale health surveys are not always well understood. Systematic follow-up studies, particularly those which pose a few repeated questions followed by open-ended discussions, are well positioned to gauge stability and consistency of data and to shed light on the intended meaning behind survey responses. Such follow-up studies require extensive coordination and face challenges in protecting respondent confidentiality during the process of recontacting and reinterviewing participants. We describe practical field strategies for undertaking a mixed methods follow-up study during a large-scale health survey. The study was designed as a mixed methods follow-up study embedded within the 2014 Ghana Demographic and Health Survey (GDHS). The study was implemented in 13 clusters. Android tablets were used to import reference data from the parent survey and to administer the questionnaire, which asked a mixture of closed- and open-ended questions on reproductive intentions, decision-making, and family planning. Despite a number of obstacles related to recontacting respondents and concern about respondent fatigue, over 92 percent of the selected sub-sample were successfully recontacted and reinterviewed; all consented to audio recording. A confidential linkage between GDHS data, follow-up tablet data, and audio transcripts was successfully created for the purpose of analysis. We summarize the challenges in follow-up study design, including ethical considerations, sample size, auditing, filtering, successful use of tablets, and share lessons learned for future such follow-up surveys.

Global change technology architecture trade study

NASA Technical Reports Server (NTRS)

Garrett, L. Bernard (Editor); Hypes, Warren D. (Editor); Wright, Robert L. (Editor)

1991-01-01

Described here is an architecture trade study conducted by the Langley Research Center to develop a representative mix of advanced space science instrumentation, spacecraft, and mission orbits to assist in the technology selection processes. The analyses concentrated on the highest priority classes of global change measurements which are the global climate changes. Issues addressed in the tradeoffs includes assessments of the economics of scale of large platforms with multiple instruments relative to smaller spacecraft; the influences of current and possible future launch vehicles on payload sizes, and on-orbit assembly decisions; and the respective roles of low-Earth versus geostationary Earth orbiting systems.

The Three-Dimensionality of Spiral Shocks: Did Chondrules Catch a Breaking Wave?

NASA Astrophysics Data System (ADS)

Boley, A. C.; Durisen, R. H.; Pickett, M. K.

2005-12-01

Spiral shocks in vertically stratified disks lead to hydraulic/shock-jumps (hs-jumps) that stimulate large scale (tenths of an AU or more) radial and vertical motions, breaking surface waves, high-altitude shocks, and vortical flows. These effects are demonstrated by three-dimensional hydrodynamics simulations in Solar Nebula models. Trajectories of fluid elements, along with their thermal histories, suggest that hs-jumps mix the nebular gas and provide diverse pre-shock conditions, some of which are conducive to chondrule formation. In addition, hs-jumps may provide an energy source for driving nebular turbulence to size-sort chondrules.

Opening the spaceways

NASA Astrophysics Data System (ADS)

Sponable, Jess M.

2000-01-01

Identifies spaceplane technical concepts proposed by both large and small companies. Highlights that the size and complexity of spaceplanes can be bounded by two well-defined concepts: the Lockheed Martin X-33/Venturestar concept and the Boeing Military Spaceplane vehicle. Also identifies a number of spaceplane concepts being proposed by small commercially financed companies. Reviews possible policy, regulatory, technology, financing and market catalysts that the government and Congress can establish to improve the business climate and encourage investment in spaceplane ventures. Argues that the government has a role and an obligation to help open the spaceways through a prudent mix of government investments and business incentives. .

Structures and textures of the Murchison and Mighei carbonaceous chondrite matrices

NASA Technical Reports Server (NTRS)

Mackinnon, I. D. R.

1980-01-01

High-resolution transmission electron microscopy has confirmed earlier observations that the character of the Murchison and Mighei fine-grained matrices is complex in mineralogy and texture. Layer structure minerals occur as planar laths, rounded grains or subhedral grains, and range in size from less than 100 A to about 1 micrometer. Serpentine-type and brucite-type structures predominate in the CM matrices. The occurrence of Povlen chrysolite and a vein of disordered mixed-layer and brucite-type material cutting a large lizardite-type grain suggests that at least some of the matrix materials were formed by alteration of preexisting material.

Biotechnology

NASA Image and Video Library

2003-05-05

Aboard the International Space Station (ISS), the Tissue Culture Module (TCM) is the stationary bioreactor vessel in which cell cultures grow. However, for the Cellular Biotechnology Operations Support Systems-Fluid Dynamics Investigation (CBOSS-FDI), color polystyrene beads are used to measure the effectiveness of various mixing procedures. The beads are similar in size and density to human lymphoid cells. Uniform mixing is a crucial component of CBOSS experiments involving the immune response of human lymphoid cell suspensions. The goal is to develop procedures that are both convenient for the flight crew and are optimal in providing uniform and reproducible mixing of all components, including cells. The average bead density in a well mixed TCM will be uniform, with no bubbles, and it will be measured using the absorption of light. In this photograph, a TCM is shown after mixing protocols, and bubbles of various sizes can be seen.

Structural ordering of casein micelles on silicon nitride micro-sieves during filtration.

PubMed

Gebhardt, Ronald; Holzmüller, Wolfgang; Zhong, Qi; Müller-Buschbaum, Peter; Kulozik, Ulrich

2011-11-01

The paper reports on the structure and formation of casein micelle deposits on silicon nitride micro-sieves during the frontal filtration. The most frequent radius of the fractionated casein micelles we use is R=60 nm as detected by static light scattering (SLS) and atomic force microscopy (AFM). We estimate the size and size distribution of the casein micelles which pass through the micro-sieve during the filtration process. A sharpening of the size distribution at the beginning of the filtration process (t=40s) is followed by a broadening and a shift of the most frequent radii towards smaller sizes at later times (t=840 s). The size distribution of the micelles deposited on the micro-sieve during filtration is bimodal and consists of the largest and smallest micelles. At larger filtration times, we observe a shift of both deposited size classes towards smaller sizes. The atomic force micrographs of the reference sample reveal a tendency of the casein micelles to order in a hexagonal lattice when deposited on the micro-sieves by solution casting. The deposition of two size classes can be explained by a formation of a mixed hexagonal lattice with large micelles building up the basis lattice and smaller sizes filling octahedral and tetrahedral holes of the lattice. The accompanied compression with increasing thickness of the casein layer could result from preferential deposition of smaller sizes in the course of the filtration. Copyright © 2011 Elsevier B.V. All rights reserved.

Stretching Diagnostics and Mixing Properties In The Stratosphere

NASA Astrophysics Data System (ADS)

Legras, B.; Shuckburgh, E.

The "finite size Lyapunov exponent" and the "effective diffusivity" are two diagnos- tics of mixing which have been recently introduced to investigate atmospheric flows. Both have been used to successfully identify the barriers to transport, for instance at the edge of the stratospheric polar vortex. Here we compare the two diagnostics in detail. The equivalent length has the advantage of arising as a mixing quantification from a rigid theoretical framework, however it has the disadvantage of being an aver- age quantity (the average around a tracer contour). The finite size Lyapunov exponent may be defined at any point in the flow, and quantifies the stretching properties expe- rienced by a fluid parcel both in its past and future evolution. In particular, the lines of maximum stretching at any time delineate the building blocks of the chaotic stirring. However the interpretation of the finite size Lyapunov exponent as a mixing time is less direct and depends on the alignment of tracer contours with the stretching lines.

Ice cream structural elements that affect melting rate and hardness.

PubMed

Muse, M R; Hartel, R W

2004-01-01

Statistical models were developed to reveal which structural elements of ice cream affect melting rate and hardness. Ice creams were frozen in a batch freezer with three types of sweetener, three levels of the emulsifier polysorbate 80, and two different draw temperatures to produce ice creams with a range of microstructures. Ice cream mixes were analyzed for viscosity, and finished ice creams were analyzed for air cell and ice crystal size, overrun, and fat destabilization. The ice phase volume of each ice cream were calculated based on the freezing point of the mix. Melting rate and hardness of each hardened ice cream was measured and correlated with the structural attributes by using analysis of variance and multiple linear regression. Fat destabilization, ice crystal size, and the consistency coefficient of the mix were found to affect the melting rate of ice cream, whereas hardness was influenced by ice phase volume, ice crystal size, overrun, fat destabilization, and the rheological properties of the mix.

Genetic and maternal effect influences on viability of common frog tadpoles under different environmental conditions.

PubMed

Pakkasmaa, S; Merilä, J; O'Hara, R B

2003-08-01

The influence of environmental stress on the expression of genetic and maternal effects on the viability traits has seldom been assessed in wild vertebrates. We have estimated genetic and maternal effects on the viability (viz probability of survival, probability of being deformed, and body size and shape) of common frog, Rana temporaria, tadpoles under stressful (low pH) and nonstressful (neutral pH) environmental conditions. A Bayesian analysis using generalized linear mixed models was applied to data from a factorial laboratory experiment. The expression of additive genetic variance was independent of pH treatments, and all traits were significantly heritable (survival: h2 approximately 0.08; deformities: h2 approximately 0.26; body size: h2 approximately 0.12; body shape: h2 approximately 0.14). Likewise, nonadditive genetic contributions to variation in all traits were significant, independent of pH treatments and typically of magnitude similar to the additive genetic effects. Maternal effects were large for all traits, especially for viability itself, and their expression was partly dependent on the environment. In the case of body size, the maternal effects were mediated largely through egg size. In general, the results give little evidence for the conjecture that environmental stress created by low pH would impact strongly on the genetic architecture of fitness-related traits in frogs, and hamper adaptation to stress caused by acidification. The low heritabilities and high dominance contributions conform to the pattern typical for traits subject to relatively strong directional selection.

Biased phylodynamic inferences from analysing clusters of viral sequences

PubMed Central

Xiang, Fei; Frost, Simon D. W.

2017-01-01

Abstract Phylogenetic methods are being increasingly used to help understand the transmission dynamics of measurably evolving viruses, including HIV. Clusters of highly similar sequences are often observed, which appear to follow a ‘power law’ behaviour, with a small number of very large clusters. These clusters may help to identify subpopulations in an epidemic, and inform where intervention strategies should be implemented. However, clustering of samples does not necessarily imply the presence of a subpopulation with high transmission rates, as groups of closely related viruses can also occur due to non-epidemiological effects such as over-sampling. It is important to ensure that observed phylogenetic clustering reflects true heterogeneity in the transmitting population, and is not being driven by non-epidemiological effects. We qualify the effect of using a falsely identified ‘transmission cluster’ of sequences to estimate phylodynamic parameters including the effective population size and exponential growth rate under several demographic scenarios. Our simulation studies show that taking the maximum size cluster to re-estimate parameters from trees simulated under a randomly mixing, constant population size coalescent process systematically underestimates the overall effective population size. In addition, the transmission cluster wrongly resembles an exponential or logistic growth model 99% of the time. We also illustrate the consequences of false clusters in exponentially growing coalescent and birth-death trees, where again, the growth rate is skewed upwards. This has clear implications for identifying clusters in large viral databases, where a false cluster could result in wasted intervention resources. PMID:28852573

Size selection from fishways and potential evolutionary responses in a threatened Atlantic salmon population

USGS Publications Warehouse

Maynard, George A.; Kinnison, M.T.; Zydlewski, Joseph D.

2017-01-01

The evolutionary effects of harvest on wild fish populations have been documented around the world; however, sublethal selective pressures can also cause evolutionary changes in phenotypes. For migratory fishes, passage facilities may represent instances of nonlethal selective pressure. Our analysis of 6 years of passage data suggests that certain fish passage facilities on the Penobscot River have been exerting selective pressure against large-bodied, anadromous Atlantic salmon (Salmo salar). At the second and third dams in the river, a 91-cm salmon was 21%–27% and 12%–16% less likely to pass than a 45-cm salmon, respectively. Fish size positively influences egg survival and number and is a heritable trait. Therefore, in a wild-reproducing population, exclusion of large fish from spawning areas may have population-level impacts. In the Penobscot River, most returning adults derive from a hatchery program that collects its broodstock after passing the first dam in the river. Analysis of fork lengths of salmon returning to the Penobscot River from 1978 to 2012 provided mixed support for evolution of size at maturity in different age classes in a pattern that may be expected from interactions with conservation hatchery operations. Additionally, slow-maturing and iteroparous individuals that represent the largest salmon size classes were essentially lost from the population during that time, and Penobscot River fish have shorter fork lengths at maturity than Atlantic salmon in undammed systems.

Individual Aerosol Particles from Biomass Burning in Southern Africa. 1; Compositions and Size Distributions of Carbonaceous Particles

NASA Technical Reports Server (NTRS)

Posfai, Mihaly; Simonics, Renata; Li, Jia; Hobbs, Peter V.; Buseck, Peter R.

2003-01-01

Individual aerosol particles in smoke plumes from biomass fires and in regional hazes in southern Africa were studied using analytical transmission electron microscopy (TEM), which allowed detailed characterization of carbonaceous particle types in smoke and determination of changes in particle properties and concentrations during smoke aging. Based on composition, morphology, and microstructure, three distinct types of carbonaceous particles were present in the smoke: organic particles with inorganic (K-salt) inclusions, tar ball particles, and soot. The relative number concentrations of organic particles were largest in young smoke, whereas tar balls were dominant in a slightly aged (1 hour) smoke from a smoldering fire. Flaming fires emitted relatively more soot particles than smoldering fires, but soot was a minor constituent of all studied plumes. Further aging caused the accumulation of sulfate on organic and soot particles, as indicated by the large number of internally mixed organic/sulfate and soot/sulfate particles in the regional haze. Externally mixed ammonium sulfate particles dominated in the boundary layer hazes, whereas organic/sulfate particles were the most abundant type in the upper hazes. Apparently, elevated haze layers were more strongly affected by biomass smoke than those within the boundary layer. Based on size distributions and the observed patterns of internal mixing, we hypothesize that organic and soot particles are the cloud-nucleating constituents of biomass smoke aerosols. Sea-salt particles dominated in the samples taken in stratus clouds over the Atlantic Ocean, off the coast of Namibia, whereas a distinct haze layer above the clouds consisted of aged biomass smoke particles.

Comparison of aerosol effects on simulated spring and summer hailstorm clouds

NASA Astrophysics Data System (ADS)

Yang, Huiling; Xiao, Hui; Guo, Chunwei; Wen, Guang; Tang, Qi; Sun, Yue

2017-07-01

Numerical simulations are carried out to investigate the effect of cloud condensation nuclei (CCN) concentrations on microphysical processes and precipitation characteristics of hailstorms. Two hailstorm cases are simulated, a spring case and a summer case, in a semiarid region of northern China, with the Regional Atmospheric Modeling System. The results are used to investigate the differences and similarities of the CCN effects between spring and summer hailstorms. The similarities are: (1) The total hydrometeor mixing ratio decreases, while the total ice-phase mixing ratio enhances, with increasing CCN concentration; (2) Enhancement of the CCN concentration results in the production of a greater amount of small-sized hydrometeor particles, but a lessening of large-sized hydrometeor particles; (3) As the CCN concentration increases, the supercooled cloud water and rainwater make a lesser contribution to hail, while the ice-phase hydrometeors take on active roles in the growth of hail; (4) When the CCN concentration increases, the amount of total precipitation lessens, while the role played by liquid-phase rainfall in the amount of total precipitation reduces, relatively, compared to that of ice-phase precipitation. The differences between the two storms include: (1) An increase in the CCN concentration tends to reduce pristine ice mixing ratios in the spring case but enhance them in the summer case; (2) Ice-phase hydrometeor particles contribute more to hail growth in the spring case, while liquid water contributes more in the summer case; (3) An increase in the CCN concentration has different effects on surface hail precipitation in different seasons.

Change in mental health after smoking cessation: systematic review and meta-analysis

PubMed Central

McNeill, Ann; Girling, Alan; Farley, Amanda; Lindson-Hawley, Nicola

2014-01-01

Objective To investigate change in mental health after smoking cessation compared with continuing to smoke. Design Systematic review and meta-analysis of observational studies. Data sources Web of Science, Cochrane Central Register of Controlled Trials, Medline, Embase, and PsycINFO for relevant studies from inception to April 2012. Reference lists of included studies were hand searched, and authors were contacted when insufficient data were reported. Eligibility criteria for selecting studies Longitudinal studies of adults that assessed mental health before smoking cessation and at least six weeks after cessation or baseline in healthy and clinical populations. Results 26 studies that assessed mental health with questionnaires designed to measure anxiety, depression, mixed anxiety and depression, psychological quality of life, positive affect, and stress were included. Follow-up mental health scores were measured between seven weeks and nine years after baseline. Anxiety, depression, mixed anxiety and depression, and stress significantly decreased between baseline and follow-up in quitters compared with continuing smokers: the standardised mean differences (95% confidence intervals) were anxiety −0.37 (95% confidence interval −0.70 to −0.03); depression −0.25 (−0.37 to −0.12); mixed anxiety and depression −0.31 (−0.47 to −0.14); stress −0.27 (−0.40 to −0.13). Both psychological quality of life and positive affect significantly increased between baseline and follow-up in quitters compared with continuing smokers 0.22 (0.09 to 0.36) and 0.40 (0.09 to 0.71), respectively). There was no evidence that the effect size differed between the general population and populations with physical or psychiatric disorders. Conclusions Smoking cessation is associated with reduced depression, anxiety, and stress and improved positive mood and quality of life compared with continuing to smoke. The effect size seems as large for those with psychiatric disorders as those without. The effect sizes are equal or larger than those of antidepressant treatment for mood and anxiety disorders. PMID:24524926

Development of dispersion-strengthened XD (trademark) Cu alloys for high heat-flux applications

NASA Technical Reports Server (NTRS)

Kumar, K. Sharvan

1993-01-01

In a previous effort sponsored by NASA LeRC, the XD(trademark) process was used to produce ZrB2 particulate reinforcements in Cu and the resulting extruded material was microstructurally characterized and evaluated in tension over a range of temperatures. A problem that was encountered in that study was microstructural inhomogeneity resulting from the frequent presence of 'ZrB2 agglomerates' that were several microns in size. The presence of these agglomerates was attributed to improper mixing of powders in the green compact used in the XD process for elemental boron powder segregation. In this program, several milling parameters were examined in an effort to optimize this processing step; two levels of ZrB2 reinforcements were considered (7 vol. percent and 15 vol. percent). Microstructures of the reacted powder mass were examined to verify the absence of these agglomerates. Larger bathes of powder were then mixed, reacted, machined to size, canned, and extruded. The microstructure and tensile properties of these extrusions were examined, and the measured properties were correlated with the observed microstructure. Large unreacted or partially reacted Zr particles were present. These particles affected the mechanical properties deleteriously, and their presence is attributed to insufficient heat of reaction during XD synthesis. Alternate processing routes are recommended.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glicken, H.

Large volcanic debris avalanches are among the world's largest mass movements. The rockslide-debris avalanche of the May 18, 1980, eruption of Mount St. Helens produced a 2.8 km/sup 3/ deposit and is the largest historic mass movement. A Pleistocene debris avalanche at Mount Shasta produced a 26 km/sup 3/ deposit that may be the largest Quaternary mass movement. The hummocky deposits at both volcanoes consist of rubble divided into (1) block facies that comprises unconsolidated pieces of the old edifice transported relatively intact, and (2) matrix facies that comprises a mixture of rocks from the old mountain and material pickedmore » up from the surrounding terrain. At Mount St. Helens, the juvenile dacite is found in the matrix facies, indicating that matrix facies formed from explosions of the erupting magma as well as from disaggregation and mixing of blocks. The block facies forms both hummocks and interhummock areas in the proximal part of the St. Helens avalanche deposit. At Mount St. Helens, the density of the old cone is 21% greater than the density of the avalanche deposit. Block size decreases with distance. Clast size, measured in the field and by sieving, coverages about a mean with distance, which suggests that blocks disaggregated and mixed together during transport.« less

[Microclimate dynamics of pit and mound complex within different sizes of forest gaps in Pinus koraiensis-dominated broadleaved mixed forest].

PubMed

Wei, Quan-Shuai; Wang, Jing-Hua; Duan, Wen-Biao; Chen, Li-Xin; Wang, Ting; Han, Dong-Hui; Gu, Wei

2014-03-01

An investigation was conducted in a 2.25 hm2 plot of Pinus koraiensis-dominated broad-leaved mixed forest to study basic characteristics of 7 small gaps, 5 middle gaps, 3 large gaps and 7 closed stands within 38 pit and mound complexes caused by treefall in May 2012. From June to September 2012, the soil temperature, soil water content and relative humidity at five microsites (pit bottom, pit wall, mound top, mound face and undisturbed closed stands) were measured in six sunny days each month. The results showed that among the five microsites in every month, the mound top had the highest soil temperature and the lowest water content and relative humidity, and vice versa for the pit bottom. Mostly, the differences in the above indicators among the five microsites were significant. From June to September, the mean soil temperatures for all microsites at pit and mound complex in the various gaps and closed stands were in the order of large gap>middle gap >small gap>closed stand; but the soil water content ranked differently every month. In June, August and September, the mean relative humidities for all microsites in the various gaps and closed stands were in the order of closed stand>small gap>middle gap>large gap. Mostly, the differences in the above indicators between all microsites in the various gaps and closed stand were significant. The mean monthly soil temperature and relative humidity were highest in July, but lowest in September. The maximal mean monthly soil water content occurred in July and the minimal one in September for each microsite except the undisturbed closed stands, where the maximal mean monthly soil water content occurred in July. The variation of the microclimate at the pit and mound complex was mainly influenced by gap size, microsite, and time.

Group-size-mediated habitat selection and group fusion-fission dynamics of bison under predation risk.

PubMed

Fortin, Daniel; Fortin, Marie-Eve; Beyer, Hawthorne L; Duchesne, Thierry; Courant, Sabrina; Dancose, Karine

2009-09-01

For gregarious animals the cost-benefit trade-offs that drive habitat selection may vary dynamically with group size, which plays an important role in foraging and predator avoidance strategies. We examined how habitat selection by bison (Bison bison) varied as a function of group size and interpreted these patterns by testing whether habitat selection was more strongly driven by the competing demands of forage intake vs. predator avoidance behavior. We developed an analytical framework that integrated group size into resource selection functions (RSFs). These group-size-dependent RSFs were based on a matched case-control design and were estimated using conditional logistic regression (mixed and population-averaged models). Fitting RSF models to bison revealed that bison groups responded to multiple aspects of landscape heterogeneity and that selection varied seasonally and as a function of group size. For example, roads were selected in summer, but not in winter. Bison groups avoided areas of high snow water equivalent in winter. They selected areas composed of a large proportion of meadow area within a 700-m radius, and within those areas, bison selected meadows. Importantly, the strength of selection for meadows varied as a function of group size, with stronger selection being observed in larger groups. Hence the bison-habitat relationship depended in part on the dynamics of group formation and division. Group formation was most likely in meadows. In contrast, risk of group fission increased when bison moved into the forest and was higher during the time of day when movements are generally longer and more variable among individuals. We also found that stronger selection for meadows by large rather than small bison groups was caused by longer residence time in individual meadows by larger groups and that departure from meadows appears unlikely to result from a depression in food intake rate. These group-size-dependent patterns were consistent with the hypothesis that avoidance of predation risk is the strongest driver of habitat selection.

Impact of mixing time and energy on the dispersion effectiveness and droplets size of oil.

PubMed

Pan, Zhong; Zhao, Lin; Boufadel, Michel C; King, Thomas; Robinson, Brian; Conmy, Robyn; Lee, Kenneth

2017-01-01

The effects of mixing time and energy on Alaska Northern Slope (ANS) and diluted bitumen Cold Lake Blend (CLB) were investigated using EPA baffled flask test. Dispersion effectiveness and droplet size distribution were measured after 5-120 min. A modeling method to predict the mean droplet size was introduced for the first time to tentatively elucidate the droplet size breakup mechanism. The ANS dispersion effectiveness greatly increased with dispersant and mixing energy. However, little CLB dispersion was noted at small energy input (ε = 0.02 Watt/kg). With dispersant, the ANS droplet size distribution reached quasi-equilibrium within 10 min, but that of CLB seems to reach quasi-equilibrium after 120 min. Dispersants are assumed ineffective on high viscosity oils because dispersants do not penetrate them. We provide an alternative explanation based on the elongation time of the droplets and its residence in high intensity zones. When mixing energy is small, CLB did not disperse after 120 min, long enough to allow the surfactant penetration. Our findings suggest that dispersants may disperse high viscosity oils at a rougher sea state and a longer time. The latter could determine how far offshore one can intervene for effective responses to a high viscosity oil spill offshore. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biophysical Interactions Control the Size and Abundance of Large Phytoplankton Chains at the Ushant Tidal Front

PubMed Central

Landeira, José M.; Ferron, Bruno; Lunven, Michel; Morin, Pascal; Marié, Louis; Sourisseau, Marc

2014-01-01

Phytoplankton blooms are usually dominated by chain-forming diatom species that can alter food pathways from primary producers to predators by reducing the interactions between intermediate trophic levels. The food-web modifications are determined by the length of the chains; however, the estimation is biased because traditional sampling strategies damage the chains and, therefore, change the phytoplankton size structure. Sedimentological studies around oceanic fronts have shown high concentrations of giant diatom mats (>1 cm in length), suggesting that the size of diatom chains is underestimated in the pelagic realm. Here, we investigate the variability in size and abundance of phytoplankton chains at the Ushant tidal front (NW France) using the Video Fluorescence Analyzer (VFA), a novel and non-invasive system. CTD and Scanfish profiling characterized a strong temperature and chlorophyll front, separating mixed coastal waters from the oceanic-stratified domain. In order to elucidate spring-neap variations in the front, vertical microstructure profiler was used to estimate the turbulence and vertical nitrate flux. Key findings were: (1) the VFA system recorded large diatom chains up to 10.7 mm in length; (2) chains were mainly distributed in the frontal region, with maximum values above the pycnocline in coincidence with the maximum chlorophyll; (3) the diapycnal fluxes of nitrate enabled the maintenance of the bloom in the frontal area throughout the spring-neap tidal cycle; (4) from spring to neap tide the chains length was significantly reduced; (5) during neap tide, the less intense vertical diffusion of nutrients, as well as the lower turbulence around the chains, intensified nutrient-depleted conditions and, thus, very large chains became disadvantageous. To explain this pattern, we suggest that size plasticity is an important ecological trait driving phytoplankton species competition. Although this plasticity behavior is well known from experiments in the laboratory, it has never been reported from observations in the field. PMID:24587384

The Effects of Fat Structures and Ice Cream Mix Viscosity on Physical and Sensory Properties of Ice Cream.

PubMed

Amador, Julia; Hartel, Rich; Rankin, Scott

2017-08-01

The purpose of this work was to investigate iciness perception and other sensory textural attributes of ice cream due to ice and fat structures and mix viscosity. Two studies were carried out varying processing conditions and mix formulation. In the 1st study, ice creams were collected at -3, -5, and -7.5 °C draw temperatures. These ice creams contained 0%, 0.1%, or 0.2% emulsifier, an 80:20 blend of mono- and diglycerides: polysorbate 80. In the 2nd study, ice creams were collected at -3 °C draw temperature and contained 0%, 0.2%, or 0.4% stabilizer, a blend of guar gum, locust bean gum, and carrageenan. Multiple linear regressions were used to determine relationships between ice crystal size, destabilized fat, and sensory iciness. In the ice and fat structure study, an inverse correlation was found between fat destabilization and sensory iciness. Ice creams with no difference in ice crystal size were perceived to be less icy with increasing amounts of destabilized fat. Destabilized fat correlated inversely with drip-through rate and sensory greasiness. In the ice cream mix viscosity study, an inverse correlation was found between mix viscosity and sensory iciness. Ice creams with no difference in ice crystal size were perceived to be less icy when formulated with higher mix viscosity. A positive correlation was found between mix viscosity and sensory greasiness. These results indicate that fat structures and mix viscosity have significant effects on ice cream microstructure and sensory texture including the reduction of iciness perception. © 2017 Institute of Food Technologists®.

Diversity and community composition of pico- and nanoplanktonic protists in the Vistula River estuary (Gulf of Gdańsk, Baltic Sea)

NASA Astrophysics Data System (ADS)

Piwosz, Kasia; Całkiewicz, Joanna; Gołębiewski, Marcin; Creer, Simon

2018-07-01

Pico- and nanoplanktonic protists (eukaryotic microorganisms with cell size of <3 μm and 3-20 μm, respectively) are the key component of plankton communities. However, their diversity and distribution patterns along environmental factors are still poorly recognized, largely due to their very large phylogenetic diversity that has been determined only via the application of molecular methods over the past two decades. Here, we compared diversity and composition of active communities of pico- and nanoplantonic protists from three zones of the Vistula River estuary (Gulf of Gdańsk): freshwater, mixing (salinity 3.5) and brackish (salinity 7), in four seasons, by pyrosequencing the V3-V4 fragment of 18S rRNA taxonomy marker gene libraries. Alpha diversity was the highest at the brackish site, but the OTU (Operational Taxonomic Units) richness was characteristic for specific protist groups at each site. The active protistan communities in the freshwater and mixing zones (salinity 0-3.5) were similar (sharing >72% of phylotypes) and included centric diatoms (Stephanodiscus minutulus), synurophytes from clades C, E and F, and cryptophytes. However, at salinity of 7 at the brackish site the communities were significantly different from those in freshwater/mixing zone, and showed higher contributions of Dinophyceae, Mamiellophyceae, Telonemia, and picobiliphytes. The high similarity between the freshwater and mixing site, as well as high dissimilarity of the brackish site was observed in all months, despite seasonal shifts in pico- and nanoplantonic protistan communities. Seventy five percent of the observed variability in the communities was explained by combinations of temperature, salinity, nutrients and geographical distance, indicating interplay between species sorting and mass effects in shaping the active protistan communities in the Vistula River estuary. Groups that were more active in freshwaters and the mixing zone seemed to be more affected by mass effects of mixing water masses, while those from the brackish site by environmental species sorting. Finally, we report, for the first time, presence of Radiolaria (Acantharea) from the Baltic Sea.

Summer planting of container-grown northern hardwoods

Treesearch

Raymond Graber

1978-01-01

Seedlings of paper birch and yellow birch were grown in Styrofoam blocks of two cavity sizes, 40 cc and 125 cc, in four different soil mixes. After 16 weeks, the seedlings were outplanted on a cleared forest site in mid July. Seedling survival for all treatments after two growing seasons was very good (98.8 percent). The effects of container size and soil mix were...

Size matters in the water uptake and hygroscopic growth of atmospherically relevant multicomponent aerosol particles.

PubMed

Laskina, Olga; Morris, Holly S; Grandquist, Joshua R; Qin, Zhen; Stone, Elizabeth A; Tivanski, Alexei V; Grassian, Vicki H

2015-05-14

Understanding the interactions of water with atmospheric aerosols is crucial for determining the size, physical state, reactivity, and climate impacts of this important component of the Earth's atmosphere. Here we show that water uptake and hygroscopic growth of multicomponent, atmospherically relevant particles can be size dependent when comparing 100 nm versus ca. 6 μm sized particles. It was determined that particles composed of ammonium sulfate with succinic acid and of a mixture of chlorides typical of the marine environment show size-dependent hygroscopic behavior. Microscopic analysis of the distribution of components within the aerosol particles show that the size dependence is due to differences in the mixing state, that is, whether particles are homogeneously mixed or phase separated, for different sized particles. This morphology-dependent hygroscopicity has consequences for heterogeneous atmospheric chemistry as well as aerosol interactions with electromagnetic radiation and clouds.

Compaction and measurement of field density for Oregon open-graded (F-MIX) asphalt pavement

DOT National Transportation Integrated Search

1999-06-01

A research project conducted by Oregon State University (OSU) and the Oregon Department of Transportation (ODOT) investigated compaction of Oregon F-mix asphalt pavement, an open-graded mix with 25-mm maximum size aggregate and air voids typically in...

Relating rheology to geometry in large-scale natural shear zones

NASA Astrophysics Data System (ADS)

Platt, John

2016-04-01

The geometry and width of the ductile roots of plate boundary scale faults are very poorly understood. Some field and geophysical data suggests widths of tens of km in the lower crust, possibly more in the upper mantle. Other observations suggest they are much narrower. Dip slip shear zones may flatten out and merge into zones of subhorizontal lower crustal or asthenospheric flow. The width of a ductile shear zone is simply related to relative velocity and strain rate. Strain rate is related to stress through the constitutive relationship. Can we constrain the stress, and do we understand the rheology of materials in ductile shear zones? A lot depends on how shear zones are initiated. If they are localized by pre-existing structures, width and/or rheology may be inherited, and we have too many variables. If shear zones are localized primarily by shear heating, initial shear stress has to be very high (> 1 GPa) to overcome conductive heat loss, and very large feedbacks (both positive and negative) make the system highly unstable. Microstructural weakening requires a minimum level of stress to cause deformation and damage in surrounding rock, thereby buffering the stress. Microstructural weakening leads to grain-size sensitive creep, for which we have constitutive laws, but these are complicated by phase mixing in polyphase materials, by viscous anisotropy, by hydration, and by changes in mineral assemblage. Here are some questions that need to be addressed. (1) If grain-size reduction by dynamic recrystallization results in a switch to grain-size sensitive creep (GSSC) in a stress-buffered shear zone, does dynamic recrystallization stop? Does grain growth set in? If grain-size is still controlled by dislocation processes, then the effective stress exponent for GSSC is 4-5, even though the dominant mechanism may be diffusion and/or grain-boundary sliding (GBS). (2) Is phase mixing in ultramylonites primarily a result of GBS + neighbour switching, creep cavitation and diffusion, or metamorphic reactions? (3) In two-phase / polyphase mixtures, does the strong phase generally form a load-bearing framework, favoring constant strain-rate (Voigt) bound behavior, or does the weak phase form through-going strain pathways, favoring constant stress (Reuss) bound behavior, or do the phases remain well mixed, favoring an intermediate behavior (e.g., Tullis et al model)? (4) How do we deal with the rheological effect of water? Is it simply an unconstrained variable in nature? Is the water fugacity model in flow laws adequate? (5) How can we better relate experimental results (often carried out at constant strain-rate, and not reaching microstructural steady state) to deformation in natural shear zones? Rheological observations on well-constrained natural shear zones are helping us answer some of these questions.

Cellular Biotechnology Operations Support Systems-Fluid Dynamics Investigation (CBOSS-FDI)

NASA Technical Reports Server (NTRS)

2003-01-01

Aboard the International Space Station (ISS), the Tissue Culture Module (TCM) is the stationary bioreactor vessel in which cell cultures grow. However, for the Cellular Biotechnology Operations Support Systems-Fluid Dynamics Investigation (CBOSS-FDI), color polystyrene beads are used to measure the effectiveness of various mixing procedures. The beads are similar in size and density to human lymphoid cells. Uniform mixing is a crucial component of CBOSS experiments involving the immune response of human lymphoid cell suspensions. The goal is to develop procedures that are both convenient for the flight crew and are optimal in providing uniform and reproducible mixing of all components, including cells. The average bead density in a well mixed TCM will be uniform, with no bubbles, and it will be measured using the absorption of light. In this photograph, a TCM is shown after mixing protocols, and bubbles of various sizes can be seen.

Effect of Dietary Countermeasures and Impact of Gravity on Renal Calculi Size Distributions Predicted by PBE-System and PBE-CFD Models

NASA Technical Reports Server (NTRS)

Kassemi, M.; Thompson, D.; Goodenow, D.; Gokoglu, S.; Myers, J.

2016-01-01

Renal stone disease is not only a concern on earth but can conceivably pose a serious risk to the astronauts health and safety in Space. In this work, two different deterministic models based on a Population Balance Equation (PBE) analysis of renal stone formation are developed to assess the risks of critical renal stone incidence for astronauts during space travel. In the first model, the nephron is treated as a continuous mixed suspension mixed product removal crystallizer and the PBE for the nucleating, growing and agglomerating renal calculi is coupled to speciation calculations performed by JESS. Predictions of stone size distributions in the kidney using this model indicate that the astronaut in microgravity is at noticeably greater but still subcritical risk and recommend administration of citrate and augmented hydration as effective means of minimizing and containing this risk. In the second model, the PBE analysis is coupled to a Computational Fluid Dynamics (CFD) model for flow of urine and transport of Calcium and Oxalate in the nephron to predict the impact of gravity on the stone size distributions. Results presented for realistic 3D tubule and collecting duct geometries, clearly indicate that agglomeration is the primary mode of size enhancement in both 1g and microgravity. 3D numerical simulations seem to further indicate that there will be an increased number of smaller stones developed in microgravity that will likely pass through the nephron in the absence of wall adhesion. However, upon reentry to a 1g (Earth) or 38g (Mars) partial gravitational fields, the renal calculi can lag behind the urinary flow in tubules that are adversely oriented with respect to the gravitational field and grow agglomerate to large sizes that are sedimented near the wall with increased propensity for wall adhesion, plaque formation, and risk to the astronauts.

Oxygen isotopic ratios in quartz as an indicator of provenance of dust

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jackson, M L

1977-01-01

Quartz was isolated in the long range aerosol size range (fine silt, 1-10 ..mu..m in diameter) from atmospheric aerosols, wind-erosive soils, soil silts, shales, and Pacific pelagic sediments of the Northern and Southern Hemispheres, to trace their provenance or origin, as part of a study of dust mineral sequestering of /sup 137/Cs and other products of nuclear fission. The oxygen isotopic ratio (/sup 18/O//sup 16/O) was determined by mass spectrometry. The provenance has been established for this fine silt fraction which reflects the relative proportion of two classes of quartz source: (a) weathering of igneous and metamorphic rocks (high temperaturemore » origin and low /sup 18/O//sup 16/O ratio) and (b) of quartz crystallized in cherts and overgrowths (low temperature origin and high /sup 18/O//sup 16/O ratio). This quartz mixing ratio is a basic model or paradigm. Analyses of present day atmospheric aerosols and eolian-derived soils, Pacific pelagic sediments, and now-raised Phanerozoic marine sediments show that the Northern and Southern Hemispheres have separate large-scale reservoirs of the fine grain sizes that contribute to aerosol dusts. These can be identified by distinctive values of /sup 18/O//sup 16/O ratios of the quartz therein. The difference in quartz delta/sup 18/O value in parts per thousand per ml (/sup 0///sub 00/ of about 12 +- 2 /sup 0///sub 00/ in Southern Hemisphere mixed detrital sediments and about 19 +- 2 /sup 0///sub 00/ in those of the Northern Hemisphere (for constant size, the 1-10 ..mu..m size fraction) results from the presence of a considerably larger proportion of quartz having low-temperature origin and higher delta/sup 18/O values (chert, silica overgrowths, etc.) in the Northern Hemisphere reservoirs. The early paleoclimatic and paleogeochemical differences remain the control of the North-South Hemisphere difference in delta/sup 18/O values in long-range aerosol sized quartz.« less

Sources and mixing state of size-resolved elemental carbon particles in a European megacity: Paris

NASA Astrophysics Data System (ADS)

Healy, R. M.; Sciare, J.; Poulain, L.; Kamili, K.; Merkel, M.; Müller, T.; Wiedensohler, A.; Eckhardt, S.; Stohl, A.; Sarda-Estève, R.; McGillicuddy, E.; O'Connor, I. P.; Sodeau, J. R.; Wenger, J. C.

2012-02-01

An Aerosol Time-Of-Flight Mass Spectrometer (ATOFMS) was deployed to investigate the size-resolved chemical composition of single particles at an urban background site in Paris, France, as part of the MEGAPOLI winter campaign in January/February 2010. ATOFMS particle counts were scaled to match coincident Twin Differential Mobility Particle Sizer (TDMPS) data in order to generate hourly size-resolved mass concentrations for the single particle classes observed. The total scaled ATOFMS particle mass concentration in the size range 150-1067 nm was found to agree very well with the sum of concurrent High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) and Multi-Angle Absorption Photometer (MAAP) mass concentration measurements of organic carbon (OC), inorganic ions and black carbon (BC) (R2 = 0.91). Clustering analysis of the ATOFMS single particle mass spectra allowed the separation of elemental carbon (EC) particles into four classes: (i) EC attributed to biomass burning (ECbiomass), (ii) EC attributed to traffic (ECtraffic), (iii) EC internally mixed with OC and ammonium sulfate (ECOCSOx), and (iv) EC internally mixed with OC and ammonium nitrate (ECOCNOx). Average hourly mass concentrations for EC-containing particles detected by the ATOFMS were found to agree reasonably well with semi-continuous quantitative thermal/optical EC and optical BC measurements (r2 = 0.61 and 0.65-0.68 respectively, n = 552). The EC particle mass assigned to fossil fuel and biomass burning sources also agreed reasonably well with BC mass fractions assigned to the same sources using seven-wavelength aethalometer data (r2 = 0.60 and 0.48, respectively, n = 568). Agreement between the ATOFMS and other instrumentation improved noticeably when a period influenced by significantly aged, internally mixed EC particles was removed from the intercomparison. 88% and 12% of EC particle mass was apportioned to fossil fuel and biomass burning respectively using the ATOFMS data compared with 85% and 15% respectively for BC estimated from the aethalometer model. On average, the mass size distribution for EC particles is bimodal; the smaller mode is attributed to locally emitted, mostly externally mixed EC particles, while the larger mode is dominated by aged, internally mixed ECOCNOx particles associated with continental transport events. Periods of continental influence were identified using the Lagrangian Particle Dispersion Model (LPDM) "FLEXPART". A consistent minimum between the two EC mass size modes was observed at approximately 400 nm for the measurement period. EC particles below this size are attributed to local emissions using chemical mixing state information and contribute 79% of the scaled ATOFMS EC particle mass, while particles above this size are attributed to continental transport events and contribute 21% of the EC particle mass. These results clearly demonstrate the potential benefit of monitoring size-resolved mass concentrations for the separation of local and continental EC emissions. Knowledge of the relative input of these emissions is essential for assessing the effectiveness of local abatement strategies.

The mediating effect of context variation in mixed practice for transfer of basic science.

PubMed

Kulasegaram, Kulamakan; Min, Cynthia; Howey, Elizabeth; Neville, Alan; Woods, Nicole; Dore, Kelly; Norman, Geoffrey

2015-10-01

Applying a previously learned concept to a novel problem is an important but difficult process called transfer. Practicing multiple concepts together (mixed practice mode) has been shown superior to practicing concepts separately (blocked practice mode) for transfer. This study examined the effect of single and multiple practice contexts for both mixed and blocked practice modalities on transfer performance. We looked at performance on near transfer (familiar contexts) cases and far transfer (unfamiliar contexts) cases. First year psychology students (n = 42) learned three physiological concepts in a 2 × 2 factorial study (one or two practice contexts and blocked or mixed practice). Each concept was practiced with two clinical cases; practice context was defined as the number of organ systems used (one system per concept vs. two systems). In blocked practice, two practice cases followed each concept; in mixed practice, students learned all concepts before seeing six practice cases. Transfer testing consisted of correctly classifying and explaining 15 clinical cases involving near and far transfer. The outcome was ratings of quality of explanations on a 0-3 scale. The repeated measures analysis showed a significant near versus far by organ system interaction [F(1,38) = 3.4, p < 0.002] with practice with a single context showing lower far transfer scores than near transfer [0.58 (0.37)-0.83 (0.37)] compared to the two contexts which had similar far and near transfer scores [1.19 (0.50)-1.01 (0.38)]. Practicing with two organ contexts had a significant benefit for far transfer regardless of mixed or blocked practice; the single context mixed practice group had the lowest far transfer performance; this was a large effect size (Cohen's d = 0.81). Using only one practice context during practice significantly lowers performance even with the usually superior mixed practice mode. Novices should be exposed to multiple contexts and mixed practice to facilitate transfer.

Task 1.6 - mixed waste. Topical report, April 1, 1994--September 30, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

For fifty years, the United States was involved in a nuclear arms race of immense proportions. During the majority of this period, the push was always to design new weapons, produce more weapons, and increase the size of the arsenal, maintaining an advantage over the opposition in order to protect U.S. interests. Now that the {open_quotes}Cold War{close_quotes} is over, we are faced with the imposing tasks of dismantling, cleaning up, and remediating the wide variety of problems created by this arms race. An overview of the current status of the total remediation effort within the DOE is presented in themore » DOE publication {open_quotes}ENVIRONMENTAL MANAGEMENT 1995{close_quotes} (EM 1995). Not all radioactive waste is the same though; therefore, a system was devised to categorize the different types of radioactive waste. These categories are as follows: spent fuel; high-level waste; transuranic waste; low-level waste; mixed waste; and uranium-mill tailings. Mixed waste is defined to be material contaminated with any of these categories of radioactive material plus an organic or heavy metal component. However, for this discussion, {open_quotes}mixed waste{close_quote} will pertain only to low-level mixed waste which consists of low-level radioactive waste mixed with organic solvents and or heavy metals. The area of {open_quotes}mixed-waste characterization, treatment, and disposal{close_quotes} is listed on page 6 of the EM 1995 publication as one of five focus areas for technological development, and while no more important than the others, it has become an area of critical concern for DOE. Lacking adequate technologies for treatment and disposal, the DOE stockpiled large quantities of mixed waste during the 1970s and 1980s. Legislative changes and the need for regulatory compliance have now made it expedient to develop methods of achieving final disposition for this stockpiled mixed waste.« less

Microwave Properties of Ice-Phase Hydrometeors for Radar and Radiometers: Sensitivity to Model Assumptions

NASA Technical Reports Server (NTRS)

Johnson, Benjamin T.; Petty, Grant W.; Skofronick-Jackson, Gail

2012-01-01

A simplied framework is presented for assessing the qualitative sensitivities of computed microwave properties, satellite brightness temperatures, and radar reflectivities to assumptions concerning the physical properties of ice-phase hydrometeors. Properties considered included the shape parameter of a gamma size distribution andthe melted-equivalent mass median diameter D0, the particle density, dielectric mixing formula, and the choice of complex index of refraction for ice. We examine these properties at selected radiometer frequencies of 18.7, 36.5, 89.0, and 150.0 GHz; and radar frequencies at 2.8, 13.4, 35.6, and 94.0 GHz consistent with existing and planned remote sensing instruments. Passive and active microwave observables of ice particles arefound to be extremely sensitive to the melted-equivalent mass median diameter D0 ofthe size distribution. Similar large sensitivities are found for variations in the ice vol-ume fraction whenever the geometric mass median diameter exceeds approximately 1/8th of the wavelength. At 94 GHz the two-way path integrated attenuation is potentially large for dense compact particles. The distribution parameter mu has a relatively weak effect on any observable: less than 1-2 K in brightness temperature and up to 2.7 dB difference in the effective radar reflectivity. Reversal of the roles of ice and air in the MaxwellGarnett dielectric mixing formula leads to a signicant change in both microwave brightness temperature (10 K) and radar reflectivity (2 dB). The choice of Warren (1984) or Warren and Brandt (2008) for the complex index of refraction of ice can produce a 3%-4% change in the brightness temperature depression.

Spreadsheet Calculations for Jets in Crossflow: Opposed Rows of Inline and Staggered Holes and Single and Opposed Rows with Alternating Hole Sizes

NASA Technical Reports Server (NTRS)

Holdeman, James D.; Clisset, James R.; Moder, Jeffrey P.

2010-01-01

The primary purpose of this jet-in-crossflow study was to calculate expected results for two configurations for which limited or no experimental results have been published: (1) cases of opposed rows of closely-spaced jets from inline and staggered round holes and (2) rows of jets from alternating large and small round holes. Simulations of these configurations were performed using an Excel (Microsoft Corporation) spreadsheet implementation of a NASA-developed empirical model which had been shown in previous publications to give excellent representations of mean experimental scalar results suggesting that the NASA empirical model for the scalar field could confidently be used to investigate these configurations. The supplemental Excel spreadsheet is posted with the current report on the NASA Glenn Technical Reports Server (http://gltrs.grc.nasa.gov) and can be accessed from the Supplementary Notes section as TM-2010-216100-SUPPL1.xls. Calculations for cases of opposed rows of jets with the orifices on one side shifted show that staggering can improve the mixing, particularly for cases where jets would overpenetrate slightly if the orifices were in an aligned configuration. The jets from the larger holes dominate the mixture fraction for configurations with a row of large holes opposite a row of smaller ones although the jet penetration was about the same. For single and opposed rows with mixed hole sizes, jets from the larger holes penetrated farther. For all cases investigated, the dimensionless variance of the mixture fraction decreased significantly with increasing downstream distance. However, at a given downstream distance, the variation between cases was small.

Suspended sediment dynamics in a large-scale turbidity current: Direct measurements from the deep-water Congo Canyon

NASA Astrophysics Data System (ADS)

Simmons, S.; Azpiroz, M.; Cartigny, M.; Clare, M. A.; Parsons, D. R.; Sumner, E.; Talling, P. J.

2016-12-01

Turbidity currents that transport sediment to the deep ocean deposit a greater volume of sediment than any other process on Earth. To date, only a handful of studies have directly measured turbidity currents, with flow durations ranging from a few minutes to a few hours. Our understanding of turbidity current dynamics is therefore largely derived from scaled laboratory experiments and numerical modelling. Recent years have seen the first field-scale measurements of depth-resolved velocity profiles, but sediment concentration (a key parameter for turbidity currents) remains elusive. Here, we present high resolution measurements of deep-water turbidity currents from the Congo Canyon; one of the world's largest submarine canyons. Direct measurements using acoustic Doppler current profilers (ADCPs) show that flows can last for many days, rather than hours as seen elsewhere, and provide the first quantification of concentration and grain size within deep-water turbidity currents.Velocity and backscatter were measured at 5 second intervals by an ADCP suspended 80 m above the canyon floor, at 2000 m water depth. A novel inversion method using multiple ADCP frequencies enabled quantification of sediment concentration and grain size within the flows. We identify high concentrations of coarse sediment within a thin frontal cell, which outruns a thicker, trailing body. Thus, the flows grow in length while propagating down-canyon. This is distinct from classical models and other field-scale measurements of turbidity currents. The slow-moving body is dominated by suspended fine-grained sediment. The body mixes with the surrounding fluid leaving diffuse clouds of sediment that persist for days after initial entrainment. Ambient tidal flow also controls the mixing within the body and the surrounding fluid. Our results provide a new quantification of suspended sediment within flows and the interaction with the surrounding fluid.

Internet cognitive behavioural therapy for mixed anxiety and depression: a randomized controlled trial and evidence of effectiveness in primary care.

PubMed

Newby, J M; Mackenzie, A; Williams, A D; McIntyre, K; Watts, S; Wong, N; Andrews, G

2013-12-01

Major depressive disorder (MDD) and generalized anxiety disorder (GAD) have the highest co-morbidity rates within the internalizing disorders cluster, yet no Internet-based cognitive behavioural therapy (iCBT) programme exists for their combined treatment. We designed a six-lesson therapist-assisted iCBT programme for mixed anxiety and depression. Study 1 was a randomized controlled trial (RCT) comparing the iCBT programme (n = 46) versus wait-list control (WLC; n = 53) for patients diagnosed by structured clinical interview with MDD, GAD or co-morbid GAD/MDD. Primary outcome measures were the Patient Health Questionnaire nine-item scale (depression), Generalized Anxiety Disorder seven-item scale (generalized anxiety), Kessler 10-item Psychological Distress scale (distress) and 12-item World Health Organization Disability Assessment Schedule II (disability). The iCBT group was followed up at 3 months post-treatment. In study 2, we investigated the adherence to, and efficacy of the same programme in a primary care setting, where patients (n = 136) completed the programme under the supervision of primary care clinicians. The RCT showed that the iCBT programme was more effective than WLC, with large within- and between-groups effect sizes found (>0.8). Adherence was also high (89%), and gains were maintained at 3-month follow-up. In study 2 in primary care, adherence to the iCBT programme was low (41%), yet effect sizes were large (>0.8). Of the non-completers, 30% experienced benefit. Together, the results show that iCBT is effective and adherence is high in research settings, but there is a problem of adherence when translated into the 'real world'. Future efforts need to be placed on developing improved adherence to iCBT in primary care settings.

Parental Language Mixing: Its Measurement and the Relation of Mixed Input to Young Bilingual Children's Vocabulary Size

ERIC Educational Resources Information Center

Byers-Heinlein, Krista

2013-01-01

Is parental language mixing related to vocabulary acquisition in bilingual infants and children? Bilingual parents (who spoke English and another language; n = 181) completed the Language Mixing Scale questionnaire, a new self-report measure that assesses how frequently parents use words from two different languages in the same sentence, such as…

Permanent deformation characteristics of Oregon mixes using the asphalt pavement analyzer : final report.

DOT National Transportation Integrated Search

2004-01-01

The Asphalt Pavement Analyzer (APA) device was used to characterize the impacts of various mix factors on the development of permanent deformation dense-graded mixes. Factors investigated included: aggregate size of 12.5 and 19 mm (0.5 and 0.75 in), ...

External influences on children's self-served portions at meals.

PubMed

Fisher, J O; Birch, L L; Zhang, J; Grusak, M A; Hughes, S O

2013-07-01

Large portions promote intake among children, but little is known about the external influences of the eating environment on children's self-selected portion sizes. This research experimentally tested effects of the amount of entree available and serving spoon size on children's self-served entree portions and intakes at dinner meals. A secondary objective was to identify child and family predictors of self-served entree portion sizes. A 2 × 2 within-subjects design was used, in which the amount of a pasta entree available for self-serving (275 vs 550 g) and the serving spoon size (teaspoon vs tablespoon) were systematically varied. The serving bowl size and portion sizes of all other foods offered were held constant across conditions. Conditions were spaced 1 week apart and randomly assigned. Weighed self-served entree portions and food intakes as well as demographics, maternal feeding styles and child/maternal anthropometrics were measured. Participants were 60 ethnically diverse children aged 4-6 years and their mothers. Mixed models revealed that children served themselves 40% more entree when the amount available was doubled (P<0.0001) and 13% more when the serving spoon size was tripled (P<0.05). Serving spoon size and the amount of entree available indirectly influenced children's intake, with larger self-served portion sizes related to greater entree intakes (P<0.0001). Greater self-served portions and energy intakes at the meal were seen among those children whose mothers reported indulgent or authoritarian feeding styles (P<0.001). Children's self-served portion sizes at meals are influenced by size-related facets of the eating environment and reflect maternal feeding styles.

Who mixes with whom among men who have sex with men? Implications for modelling the HIV epidemic in southern India

PubMed Central

Mitchell, K.M.; Foss, A.M.; Prudden, H.J.; Mukandavire, Z.; Pickles, M.; Williams, J.R.; Johnson, H.C.; Ramesh, B.M.; Washington, R.; Isac, S.; Rajaram, S.; Phillips, A.E.; Bradley, J.; Alary, M.; Moses, S.; Lowndes, C.M.; Watts, C.H.; Boily, M.-C.; Vickerman, P.

2014-01-01

In India, the identity of men who have sex with men (MSM) is closely related to the role taken in anal sex (insertive, receptive or both), but little is known about sexual mixing between identity groups. Both role segregation (taking only the insertive or receptive role) and the extent of assortative (within-group) mixing are known to affect HIV epidemic size in other settings and populations. This study explores how different possible mixing scenarios, consistent with behavioural data collected in Bangalore, south India, affect both the HIV epidemic, and the impact of a targeted intervention. Deterministic models describing HIV transmission between three MSM identity groups (mostly insertive Panthis/Bisexuals, mostly receptive Kothis/Hijras and versatile Double Deckers), were parameterised with behavioural data from Bangalore. We extended previous models of MSM role segregation to allow each of the identity groups to have both insertive and receptive acts, in differing ratios, in line with field data. The models were used to explore four different mixing scenarios ranging from assortative (maximising within-group mixing) to disassortative (minimising within-group mixing). A simple model was used to obtain insights into the relationship between the degree of within-group mixing, R0 and equilibrium HIV prevalence under different mixing scenarios. A more complex, extended version of the model was used to compare the predicted HIV prevalence trends and impact of an HIV intervention when fitted to data from Bangalore. With the simple model, mixing scenarios with increased amounts of assortative (within-group) mixing tended to give rise to a higher R0 and increased the likelihood that an epidemic would occur. When the complex model was fit to HIV prevalence data, large differences in the level of assortative mixing were seen between the fits identified using different mixing scenarios, but little difference was projected in future HIV prevalence trends. An oral pre-exposure prophylaxis (PrEP) intervention was modelled, targeted at the different identity groups. For intervention strategies targeting the receptive or receptive and versatile MSM together, the overall impact was very similar for different mixing patterns. However, for PrEP scenarios targeting insertive or versatile MSM alone, the overall impact varied considerably for different mixing scenarios; more impact was achieved with greater levels of disassortative mixing. PMID:24727187

Two stage hydrolysis of corn stover at high solids content for mixing power saving and scale-up applications.

PubMed

Liu, Ke; Zhang, Jian; Bao, Jie

2015-11-01

A two stage hydrolysis of corn stover was designed to solve the difficulties between sufficient mixing at high solids content and high power input encountered in large scale bioreactors. The process starts with the quick liquefaction to convert solid cellulose to liquid slurry with strong mixing in small reactors, then followed the comprehensive hydrolysis to complete saccharification into fermentable sugars in large reactors without agitation apparatus. 60% of the mixing energy consumption was saved by removing the mixing apparatus in large scale vessels. Scale-up ratio was small for the first step hydrolysis reactors because of the reduced reactor volume. For large saccharification reactors in the second step, the scale-up was easy because of no mixing mechanism was involved. This two stage hydrolysis is applicable for either simple hydrolysis or combined fermentation processes. The method provided a practical process option for industrial scale biorefinery processing of lignocellulose biomass. Copyright © 2015 Elsevier Ltd. All rights reserved.

Laboratory studies of dune sand for the use of construction industry in Sri Lanka

NASA Astrophysics Data System (ADS)

de Silva Jayawardena, Upali; Wijesuriya, Roshan; Abayaweera, Gayan; Viduranga, Tharaka

2015-04-01

With the increase of the annual sand demand for the construction industry the excessive excavation of river sand is becoming a serious environmental problem in Sri Lanka. Therefore, it is necessary to explore the possibility for an alternative to stop or at least to minimize river sand mining activities. Dune sand is one of the available alternative materials to be considered instead of river sand in the country. Large quantities of sand dunes occur mainly along the NW and SE coastal belt which belong to very low rainfall Dry Zone coasts. The height of dune deposits, vary from 1m to about 30 meters above sea level. The objective of this paper is to indicate some studies and facts on the dune sand deposits of Sri Lanka. Laboratory studies were carried out for visual observations and physical properties at the initial stage and then a number of tests were carried out according to ASTM standards to obtain the compressive strength of concrete cylinders and mortar cubes mixing dune sand and river sand in different percentages keeping a constant water cement ratio. Next the water cement ratio was changed for constant dune sand and river sand proportion. Microscopic analysis shows that the dune sand consist of 95 % of quartz and 5 % of garnet, feldspar, illmenite and other heavy minerals with clay, fine dust, fine shell fragments and organic matters. Grains are sub-rounded to angular and tabular shapes. The grain sizes vary from fine to medium size of sand with silt. The degree of sorting and particle size observed with dune sands are more suited with the requirement of fine aggregates in the construction industry. The test result indicates that dune sand could be effectively used in construction work without sieving and it is ideal for wall plastering due to its'-uniformity. It could also be effectively used in concrete and in mortars mixing with river sand. The best mixing ratio is 75% dune sand and 25% river sand as the fine aggregate of concrete. For mortar the mixing percentage is 50%. The best water cement ratio for mix proportion is 0.45. It was observed that the available amount of dune sand can be extracted to meet the demand for sand in construction industry. However, the extraction of dune sand from the areas close to the sea will cause several social, environmental and legal problems. Therefore sand mining from dunes must be commenced after making a detailed Environmental Impact Assessment.

Wintertime Experimental investigation of Morphology, Mixing States and Columnar Optical Properties of Aerosols over a Desert location in India

NASA Astrophysics Data System (ADS)

Mishra, S.; Kumar, T.; Sharma, C.; Prasad, M. V. S. N.; Singh, S.; Agnihotri, R.; Arya, B. C.; Gupta, B.; Naaraayanan, T.; Gautam, S.; Kumar, D.; Sood, K. N.; Tawale, J. S.; Sharma, A. K.; Mitra, A. K.

2014-12-01

Indian Desert (The Thar Desert) is considered as the source of mineral dust in the Indo-Gangetic Plain (IGP) especially in pre-monsoon period due to large scale convective activities during hot summer. To study the physico-chemical characteristics of aerosols over the Thar Desert (Jaisalmer, Rajasthan) during winter (December, 2013), a field campaign has been carried out in Jaisalmer in Rajasthan state. Experiments were conducted inside the city as well as far from the city. The faraway location is close to international border of another country i.e. Pakistan. PM2.5 and PM10 were collected within the city while PM5 was collected far from the city. Particles were collected on Teflon filters for bulk analysis with Fourier Transform Infrared Spectroscopy (FTIR), on Tin substrate for individual particle morphology and elemental composition analysis with Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectrometer (EDS) and on the Cu-TEM grid for individual particle morphology and mixing state characterization using High Resolution-Transmission Electron Microscope (HRTEM). Together with this, aerosol size distribution observation and columnar spectral aerosol optical properties have been carried out with OPC (Optical Particle Counter, GRIMM Model 1.108) and hand held Microtops-II, respectively. HRTEM analysis reveals occurrence of carbonaceous fractals found in various mixing states 1) aged with some hygroscopic species 2) embedded in sulfate host 3) semi-externally mixed with sulfate and other species. Core-shell particles were also observed with varying core composition (carbon, typical mineral dust, and calcite) and shell thickness (shell comprising of water). The back trajectory analysis reveals the source of wind from Karachi and Islamabad from Pakistan which may be the potential source of carbonaceous species over the sampling site. SEM-EDS analysis reveals occurrence of mineral dust 1) pure mineral dust (Ca and Si rich) 2) polluted mineral dust (mixed with carbon and Cr) together with some pollutants (rich in carbon, S, K, Cl, Mo and Nb). Signatures of various organics were traced using FTIR. Aerosol columnar spectral optical properties, size distribution and meteorology in tandem with aforementioned aerosol properties will be discussed in detail during the presentation.

Basic properties of full-size st ructural flakeboards fabricated with flakes on a shaping lathe

Treesearch

Eddie W. Prie

1977-01-01

Structural exterior flakeboards manufactured in 4 by 8 ft (1.22 by 2.44 m ) size with phenolic resin and flakes produced on a shaping-lathe headrig were evaluated for plate shear modulus, internal bond, bending properties, and 24-hour water soak stability. Both mixed and single species flakeboards were produced. Panels with mixed flakes had 20% by weight of hickory,...

Parameterization of the Extinction Coefficient in Ice and Mixed-Phase Arctic Clouds during the ISDAC Field Campaign

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korolev, A; Shashkov, A; Barker, H

This report documents the history of attempts to directly measure cloud extinction, the current measurement device known as the Cloud Extinction Probe (CEP), specific problems with direct measurement of extinction coefficient, and the attempts made here to address these problems. Extinction coefficient is one of the fundamental microphysical parameters characterizing bulk properties of clouds. Knowledge of extinction coefficient is of crucial importance for radiative transfer calculations in weather prediction and climate models given that Earth's radiation budget (ERB) is modulated much by clouds. In order for a large-scale model to properly account for ERB and perturbations to it, it mustmore » ultimately be able to simulate cloud extinction coefficient well. In turn this requires adequate and simultaneous simulation of profiles of cloud water content and particle habit and size. Similarly, remote inference of cloud properties requires assumptions to be made about cloud phase and associated single-scattering properties, of which extinction coefficient is crucial. Hence, extinction coefficient plays an important role in both application and validation of methods for remote inference of cloud properties from data obtained from both satellite and surface sensors (e.g., Barker et al. 2008). While estimation of extinction coefficient within large-scale models is relatively straightforward for pure water droplets, thanks to Mie theory, mixed-phase and ice clouds still present problems. This is because of the myriad forms and sizes that crystals can achieve, each having their own unique extinction properties. For the foreseeable future, large-scale models will have to be content with diagnostic parametrization of crystal size and type. However, before they are able to provide satisfactory values needed for calculation of radiative transfer, they require the intermediate step of assigning single-scattering properties to particles. The most basic of these is extinction coefficient, yet it is rarely measured directly, and therefore verification of parametrizations is difficult. The obvious solution is to be able to measure microphysical properties and extinction at the same time and for the same volume. This is best done by in situ sampling by instruments mounted on either balloon or aircraft. The latter is the usual route and the one employed here. Yet the problem of actually measuring extinction coefficient directly for arbitrarily complicated particles still remains unsolved.« less

Large Volume In-Situ Filtration During Sofex: an Overview of Preliminary Results

NASA Astrophysics Data System (ADS)

Lam, P. J.; Wood, T. J.; Bishop, J. K.

2002-12-01

We deployed the Multiple Unit Large Volume in-situ Filtration System (MULVFS) during the Southern Ocean Iron Experiment (SOFeX) in Jan/Feb 2002 from the R/V Revelle. The MULVFS collected samples over 4 hours of pumping at depths between the surface and 1000m from 3 flow channels: size-fractionated particles (>51μm, 1-51μm, and nominally <1μm) using a 51μm polyester mesh and a pair of microquartz fiber filters (1μm) in sequence from up to 12,000L of seawater; Th samples through absorber cartridges from up to 3500L; and >0.4μm and >0.7μm particles from up to 25L. Samples were shared with several groups in SOFeX. Profiles from the North Patch (55S 172W; hereafter "55S") were collected on Julian Day 12 before the first Fe infusion, and "in the patch" on JD 19 and 40. Five profiles were collected in the South Patch (66S, 172W; hereafter "66S"): two "out of the patch" profiles on JD 24 and 34, and three "in the patch" profiles on JD 28, 31, and 35. We observed the following in the (>51μm) size fraction: 55S was initially characterized by a predominance of small particles in the mixed layer, with very little captured on the >51μm filters. Four weeks after the first Fe addition, the >51μm samples from 35m were heavily loaded. There was a clear increase in large sized organic matter in the mixed layer, but there was no visible evidence of enhanced deep particle export at this point in the experiment. Samples collected over a shorter (12 day) period at 66S showed a concurrent natural bloom outside of the patch, obscuring detection of biomass differences inside the patch. We have calculated POC in our samples using gravimetric techniques in the >51μm fraction (polyester filter) and measured directly in the 1-51 μm and "<1μm" fractions (quartz fiber filters). We will also present preliminary results of bulk chemical analyses for CaCO3, Si, and acid leacheable bioactive trace metals, with an emphasis on iron.

Size-dependence of tree growth response to drought for Norway spruce and European beech individuals in monospecific and mixed-species stands.

PubMed

Ding, H; Pretzsch, H; Schütze, G; Rötzer, T

2017-09-01

Climate anomalies have resulted in changing forest productivity, increasing tree mortality in Central and Southern Europe. This has resulted in more severe and frequent ecological disturbances to forest stands. This study analysed the size-dependence of growth response to drought years based on 384 tree individuals of Norway spruce [Picea abies (L.) Karst.] and European beech [Fagus sylvatica ([L.)] in Bavaria, Germany. Samples were collected in both monospecific and mixed-species stands. To quantify the growth response to drought stress, indices for basal area increment, resistance, recovery and resilience were calculated from tree ring measurements of increment cores. Linear mixed models were developed to estimate the influence of drought periods. The results show that ageing-related growth decline is significant in drought years. Drought resilience and resistance decrease significantly with growth size among Norway spruce individuals. Evidence is also provided for robustness in the resilience capacity of European beech during drought stress. Spruce benefits from species mixing with deciduous beech, with over-yielding spruce in pure stands. The importance of the influence of size-dependence within tree growth studies during disturbances is highlighted and should be considered in future studies of disturbances, including drought. © 2017 German Botanical Society and The Royal Botanical Society of the Netherlands.

Long-distance plant dispersal to North Atlantic islands: colonization routes and founder effect

PubMed Central

Alsos, Inger Greve; Ehrich, Dorothee; Eidesen, Pernille Bronken; Solstad, Heidi; Westergaard, Kristine Bakke; Schönswetter, Peter; Tribsch, Andreas; Birkeland, Siri; Elven, Reidar; Brochmann, Christian

2015-01-01

Long-distance dispersal (LDD) processes influence the founder effect on islands. We use genetic data for 25 Atlantic species and similarities among regional floras to analyse colonization, and test whether the genetic founder effect on five islands is associated with dispersal distance, island size and species traits. Most species colonized postglacially via multiple dispersal events from several source regions situated 280 to >3000 km away, and often not from the closest ones. A strong founder effect was observed for insect-pollinated mixed maters, and it increased with dispersal distance and decreased with island size in accordance with the theory of island biogeography. Only a minor founder effect was observed for wind-pollinated outcrossing species. Colonization patterns were largely congruent, indicating that despite the importance of stochasticity, LDD is mainly determined by common factors, probably dispersal vectors. Our findings caution against a priori assuming a single, close source region in biogeographic analyses. PMID:25876627

Removing systematic errors in interionic potentials of mean force computed in molecular simulations using reaction-field-based electrostatics

PubMed Central

Baumketner, Andrij

2009-01-01

The performance of reaction-field methods to treat electrostatic interactions is tested in simulations of ions solvated in water. The potential of mean force between sodium chloride pair of ions and between side chains of lysine and aspartate are computed using umbrella sampling and molecular dynamics simulations. It is found that in comparison with lattice sum calculations, the charge-group-based approaches to reaction-field treatments produce a large error in the association energy of the ions that exhibits strong systematic dependence on the size of the simulation box. The atom-based implementation of the reaction field is seen to (i) improve the overall quality of the potential of mean force and (ii) remove the dependence on the size of the simulation box. It is suggested that the atom-based truncation be used in reaction-field simulations of mixed media. PMID:19292522

Head and facial anthropometry of mixed-race US Army male soldiers for military design and sizing: a pilot study.

PubMed

Yokota, Miyo

2005-05-01

In the United States, the biologically admixed population is increasing. Such demographic changes may affect the distribution of anthropometric characteristics, which are incorporated into the design of equipment and clothing for the US Army and other large organizations. The purpose of this study was to examine multivariate craniofacial anthropometric distributions between biologically admixed male populations and single racial groups of Black and White males. Multivariate statistical results suggested that nose breadth and lip length were different between Blacks and Whites. Such differences may be considered for adjustments to respirators and chemical-biological protective masks. However, based on this pilot study, multivariate anthropometric distributions of admixed individuals were within the distributions of single racial groups. Based on the sample reported, sizing and designing for the admixed groups are not necessary if anthropometric distributions of single racial groups comprising admixed groups are known.

Scramjet Combustor Characteristics at Hypervelocity Condition over Mach 10 Flight

NASA Astrophysics Data System (ADS)

Takahashi, M.; Komuro, T.; Sato, K.; Kodera, M.; Tanno, H.; Itoh, K.

2009-01-01

To investigate possibility of reduction of a scramjet combustor size without thrust performance loss, a two-dimensional constant-area combustor of a previous engine model was replaced with the one with 23% lower-height. With the application of the lower-height combustor, the pressure in the combustor becomes 50% higher and the combustor length for the optimal performance becomes 43% shorter than the original combustor. The combustion tests of the modified engine model were conducted using a large free-piston driven shock tunnel at flow conditions corresponding to the flight Mach number from 9 to 14. CFD was also applied to the engine internal flows. The results showed that the mixing and combustion heat release progress faster to the distance and the combustor performance similar to that of the previous engine was obtained with the modified engine. The reduction of the combustor size without the thrust performance loss is successfully achieved by applying the lower-height combustor.

An optimization model for energy generation and distribution in a dynamic facility

NASA Technical Reports Server (NTRS)

Lansing, F. L.

1981-01-01

An analytical model is described using linear programming for the optimum generation and distribution of energy demands among competing energy resources and different economic criteria. The model, which will be used as a general engineering tool in the analysis of the Deep Space Network ground facility, considers several essential decisions for better design and operation. The decisions sought for the particular energy application include: the optimum time to build an assembly of elements, inclusion of a storage medium of some type, and the size or capacity of the elements that will minimize the total life-cycle cost over a given number of years. The model, which is structured in multiple time divisions, employ the decomposition principle for large-size matrices, the branch-and-bound method in mixed-integer programming, and the revised simplex technique for efficient and economic computer use.

Men, women…who cares? A population-based study on sex differences and gender roles in empathy and moral cognition

PubMed Central

Baez, Sandra; Flichtentrei, Daniel; Prats, María; Mastandueno, Ricardo; García, Adolfo M.; Cetkovich, Marcelo

2017-01-01

Research on sex differences in empathy has revealed mixed findings. Whereas experimental and neuropsychological measures show no consistent sex effect, self-report data consistently indicates greater empathy in women. However, available results mainly come from separate populations with relatively small samples, which may inflate effect sizes and hinder comparability between both empirical corpora. To elucidate the issue, we conducted two large-scale studies. First, we examined whether sex differences emerge in a large population-based sample (n = 10,802) when empathy is measured with an experimental empathy-for-pain paradigm. Moreover, we investigated the relationship between empathy and moral judgment. In the second study, a subsample (n = 334) completed a self-report empathy questionnaire. Results showed some sex differences in the experimental paradigm, but with minuscule effect sizes. Conversely, women did portray themselves as more empathic through self-reports. In addition, utilitarian responses to moral dilemmas were less frequent in women, although these differences also had small effect sizes. These findings suggest that sex differences in empathy are highly driven by the assessment measure. In particular, self-reports may induce biases leading individuals to assume gender-role stereotypes. Awareness of the role of measurement instruments in this field may hone our understanding of the links between empathy, sex differences, and gender roles. PMID:28632770

The Impact of Geoengineering Aerosols on Stratospheric Temperature and Ozone

NASA Technical Reports Server (NTRS)

Heckendorn, P.; Weisenstein, D.; Fueglistaler, S.; Luo, B. P.; Rozanov, E.; Schraner, M.; Peter, T.; Thomason, L. W.

2009-01-01

Anthropogenic greenhouse gas emissions are warming the global climate at an unprecedented rate. Significant emission reductions will be required soon to avoid a rapid temperature rise. As a potential interim measure to avoid extreme temperature increase, it has been suggested that Earth's albedo be increased by artificially enhancing stratospheric sulfate aerosols. We use a 3D chemistry climate model, fed by aerosol size distributions from a zonal mean aerosol model, to simulate continuous injection of 1-10 Mt/a into the lower tropical stratosphere. In contrast to the case for all previous work, the particles are predicted to grow to larger sizes than are observed after volcanic eruptions. The reason is the continuous supply of sulfuric acid and hence freshly formed small aerosol particles, which enhance the formation of large aerosol particles by coagulation and, to a lesser extent, by condensation. Owing to their large size, these particles have a reduced albedo. Furthermore, their sedimentation results in a non-linear relationship between stratospheric aerosol burden and annual injection, leading to a reduction of the targeted cooling. More importantly, the sedimenting particles heat the tropical cold point tropopause and, hence, the stratospheric entry mixing ratio of H2O increases. Therefore, geoengineering by means of sulfate aerosols is predicted to accelerate the hydroxyl catalyzed ozone destruction cycles and cause a significant depletion of the ozone layer even though future halogen concentrations will be significantly reduced.

The Impact of Geoengineering Aerosols on Stratospheric Temperature and Ozone

NASA Technical Reports Server (NTRS)

Heckendorn, P.; Weisenstein, D.; Fueglistaler, S.; Luo, B. P.; Rozanov, E.; Schraner, M.; Thomason, L. W.; Peter, T.

2011-01-01

Anthropogenic greenhouse gas emissions are warming the global climate at an unprecedented rate. Significant emission reductions will be required soon to avoid a rapid temperature rise. As a potential interim measure to avoid extreme temperature increase, it has been suggested that Earth's albedo be increased by artificially enhancing stratospheric sulfate aerosols. We use a 3D chemistry climate model, fed by aerosol size distributions from a zonal mean aerosol model. to simulate continuous injection of 1-10 Mt/a into the lower tropical stratosphere. In contrast to the case for all previous work, the particles are predicted to grow to larger sizes than are observed after volcanic eruptions. The reason is the continuous supply of sulfuric acid and hence freshly formed small aerosol particles, which enhance the formation of large aerosol particles by coagulation and, to a lesser extent, by condensation. Owing to their large size, these particles have a reduced albedo. Furthermore, their sedimentation results in a non-linear relationship between stratospheric aerosol burden and annual injection, leading to a reduction of the targeted cooling. More importantly, the sedimenting particles heat the tropical cold point tropopause and, hence, the stratospheric entry mixing ratio of H2O increases. Therefore, geoengineering by means of sulfate aerosols is predicted to accelerate the hydroxyl catalyzed ozone destruction cycles and cause a significant depletion of the ozone layer even though future halogen concentrations will he significantly reduced.

Recalibrating disease parameters for increasing realism in modeling epidemics in closed settings.

PubMed

Bioglio, Livio; Génois, Mathieu; Vestergaard, Christian L; Poletto, Chiara; Barrat, Alain; Colizza, Vittoria

2016-11-14

The homogeneous mixing assumption is widely adopted in epidemic modelling for its parsimony and represents the building block of more complex approaches, including very detailed agent-based models. The latter assume homogeneous mixing within schools, workplaces and households, mostly for the lack of detailed information on human contact behaviour within these settings. The recent data availability on high-resolution face-to-face interactions makes it now possible to assess the goodness of this simplified scheme in reproducing relevant aspects of the infection dynamics. We consider empirical contact networks gathered in different contexts, as well as synthetic data obtained through realistic models of contacts in structured populations. We perform stochastic spreading simulations on these contact networks and in populations of the same size under a homogeneous mixing hypothesis. We adjust the epidemiological parameters of the latter in order to fit the prevalence curve of the contact epidemic model. We quantify the agreement by comparing epidemic peak times, peak values, and epidemic sizes. Good approximations of the peak times and peak values are obtained with the homogeneous mixing approach, with a median relative difference smaller than 20 % in all cases investigated. Accuracy in reproducing the peak time depends on the setting under study, while for the peak value it is independent of the setting. Recalibration is found to be linear in the epidemic parameters used in the contact data simulations, showing changes across empirical settings but robustness across groups and population sizes. An adequate rescaling of the epidemiological parameters can yield a good agreement between the epidemic curves obtained with a real contact network and a homogeneous mixing approach in a population of the same size. The use of such recalibrated homogeneous mixing approximations would enhance the accuracy and realism of agent-based simulations and limit the intrinsic biases of the homogeneous mixing.

Geologic map of the Riverside East 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Cox, Brett F.

2001-01-01

a. This Readme; includes in Appendix I, data contained in rse_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Geologic map of the Corona North 7.5' quadrangle, Riverside and San Bernardino counties, California

USGS Publications Warehouse

Morton, Douglas M.; Gray, C.H.; Bovard, Kelly R.; Dawson, Michael

2002-01-01

a. This Readme; includes in Appendix I, data contained in crn_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced precise 1:24,000- scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Geologic map of the Corona South 7.5' quadrangle, Riverside and Orange counties, California

USGS Publications Warehouse

Gray, C.H.; Morton, Douglas M.; Weber, F. Harold; Digital preparation by Bovard, Kelly R.; O'Brien, Timothy

2002-01-01

a. A Readme file; includes in Appendix I, data contained in crs_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Geologic map of the Lake Mathews 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Weber, F. Harold

2001-01-01

a. This Readme; includes in Appendix I, data contained in lkm_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Miscellaneous Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous.Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand.In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Geologic map of the Steele Peak 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; digital preparation by Alvarez, Rachel M.; Diep, Van M.

2001-01-01

a. This Readme; includes in Appendix I, data contained in stp_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Geologic map of the Riverside West 7.5' quadrangle, Riverside County, California

USGS Publications Warehouse

Morton, Douglas M.; Cox, Brett F.

2001-01-01

a. This Readme; includes in Appendix I, data contained in rsw_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat page size setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Where known, grain size is indicated on the map by a subscripted letter or letters following the unit symbols as follows: lg, large boulders; b, boulder; g, gravel; a, arenaceous; s, silt; c, clay; e.g. Qyfa is a predominantly young alluvial fan deposit that is arenaceous. Multiple letters are used for more specific identification or for mixed units, e.g., Qfysa is a silty sand. In some cases, mixed units are indicated by a compound symbol; e.g., Qyf2sc. Marine deposits are in part overlain by local, mostly alluvial fan, deposits and are labeled Qomf. Grain size follows f.Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above).

Particle-size segregation and diffusive remixing in shallow granular avalanches

NASA Astrophysics Data System (ADS)

Gray, J. M. N. T.; Chugunov, V. A.

2006-12-01

Segregation and mixing of dissimilar grains is a problem in many industrial and pharmaceutical processes, as well as in hazardous geophysical flows, where the size-distribution can have a major impact on the local rheology and the overall run-out. In this paper, a simple binary mixture theory is used to formulate a model for particle-size segregation and diffusive remixing of large and small particles in shallow gravity-driven free-surface flows. This builds on a recent theory for the process of kinetic sieving, which is the dominant mechanism for segregation in granular avalanches provided the density-ratio and the size-ratio of the particles are not too large. The resulting nonlinear parabolic segregation remixing equation reduces to a quasi-linear hyperbolic equation in the no-remixing limit. It assumes that the bulk velocity is incompressible and that the bulk pressure is lithostatic, making it compatible with most theories used to compute the motion of shallow granular free-surface flows. In steady-state, the segregation remixing equation reduces to a logistic type equation and the ‘S’-shaped solutions are in very good agreement with existing particle dynamics simulations for both size and density segregation. Laterally uniform time-dependent solutions are constructed by mapping the segregation remixing equation to Burgers equation and using the Cole Hopf transformation to linearize the problem. It is then shown how solutions for arbitrary initial conditions can be constructed using standard methods. Three examples are investigated in which the initial concentration is (i) homogeneous, (ii) reverse graded with the coarse grains above the fines, and, (iii) normally graded with the fines above the coarse grains. Time-dependent two-dimensional solutions are also constructed for plug-flow in a semi-infinite chute.

Size, sex and individual-level behaviour drive intrapopulation variation in cross-ecosystem foraging of a top-predator.

PubMed

Nifong, James C; Layman, Craig A; Silliman, Brian R

2015-01-01

Large-bodied, top-predators are often highly mobile, with the potential to provide important linkages between spatially distinct food webs. What biological factors contribute to variation in cross-ecosystem movements, however, have rarely been examined. Here, we investigated how ontogeny (body size), sex and individual-level behaviour impacts intrapopulation variation in cross-ecosystem foraging (i.e. between freshwater and marine systems), by the top-predator Alligator mississippiensis. Field surveys revealed A. mississippiensis uses marine ecosystems regularly and are abundant in estuarine tidal creeks (from 0·3 to 6·3 individuals per km of creek, n = 45 surveys). Alligator mississippiensis captured in marine/estuarine habitats were significantly larger than individuals captured in freshwater and intermediate habitats. Stomach content analysis (SCA) showed that small juveniles consumed marine/estuarine prey less frequently (6·7% of individuals) than did large juveniles (57·8%), subadult (73%), and adult (78%) size classes. Isotopic mixing model analysis (SIAR) also suggests substantial variation in use of marine/estuarine prey resources with differences among and within size classes between sexes and individuals (range of median estimates for marine/estuarine diet contribution = 0·05-0·76). These results demonstrate the importance of intrapopulation characteristics (body size, sex and individual specialization) as key determinants of the strength of predator-driven ecosystem connectivity resulting from cross-ecosystem foraging behaviours. Understanding the factors, which contribute to variation in cross-ecosystem foraging behaviours, will improve our predictive understanding of the effects of top-predators on community structure and ecosystem function. © 2014 The Authors. Journal of Animal Ecology © 2014 British Ecological Society.

Perturbation theory for cosmologies with nonlinear structure

NASA Astrophysics Data System (ADS)

Goldberg, Sophia R.; Gallagher, Christopher S.; Clifton, Timothy

2017-11-01

The next generation of cosmological surveys will operate over unprecedented scales, and will therefore provide exciting new opportunities for testing general relativity. The standard method for modelling the structures that these surveys will observe is to use cosmological perturbation theory for linear structures on horizon-sized scales, and Newtonian gravity for nonlinear structures on much smaller scales. We propose a two-parameter formalism that generalizes this approach, thereby allowing interactions between large and small scales to be studied in a self-consistent and well-defined way. This uses both post-Newtonian gravity and cosmological perturbation theory, and can be used to model realistic cosmological scenarios including matter, radiation and a cosmological constant. We find that the resulting field equations can be written as a hierarchical set of perturbation equations. At leading-order, these equations allow us to recover a standard set of Friedmann equations, as well as a Newton-Poisson equation for the inhomogeneous part of the Newtonian energy density in an expanding background. For the perturbations in the large-scale cosmology, however, we find that the field equations are sourced by both nonlinear and mode-mixing terms, due to the existence of small-scale structures. These extra terms should be expected to give rise to new gravitational effects, through the mixing of gravitational modes on small and large scales—effects that are beyond the scope of standard linear cosmological perturbation theory. We expect our formalism to be useful for accurately modeling gravitational physics in universes that contain nonlinear structures, and for investigating the effects of nonlinear gravity in the era of ultra-large-scale surveys.

Continuous manufacturing of solid lipid nanoparticles by hot melt extrusion.

PubMed

Patil, Hemlata; Kulkarni, Vijay; Majumdar, Soumyajit; Repka, Michael A

2014-08-25

Solid lipid nanoparticles (SLN) can either be produced by hot homogenization of melted lipids at higher temperatures or by a cold homogenization process. This paper proposes and demonstrates the formulation of SLN for pharmaceutical applications by combining two processes: hot melt extrusion (HME) technology for melt-emulsification and high-pressure homogenization (HPH) for size reduction. This work aimed at developing continuous and scalable processes for SLN by mixing a lipid and aqueous phase containing an emulsifier in the extruder barrel at temperatures above the melting point of the lipid and further reducing the particle size of emulsion by HPH linked to HME in a sequence. The developed novel platform demonstrated better process control and size reduction compared to the conventional process of hot homogenization (batch process). Varying the process parameters enabled the production of SLN below 200 nm (for 60 mg/ml lipid solution at a flow rate of 100ml/min). Among the several process parameters investigated, the lipid concentration, residence time and screw design played major roles in influencing the size of the SLN. This new process demonstrates the potential use of hot melt extrusion technology for continuous and large-scale production of SLN. Copyright © 2014 Elsevier B.V. All rights reserved.

Quantifying the uncertainty in heritability.

PubMed

Furlotte, Nicholas A; Heckerman, David; Lippert, Christoph

2014-05-01

The use of mixed models to determine narrow-sense heritability and related quantities such as SNP heritability has received much recent attention. Less attention has been paid to the inherent variability in these estimates. One approach for quantifying variability in estimates of heritability is a frequentist approach, in which heritability is estimated using maximum likelihood and its variance is quantified through an asymptotic normal approximation. An alternative approach is to quantify the uncertainty in heritability through its Bayesian posterior distribution. In this paper, we develop the latter approach, make it computationally efficient and compare it to the frequentist approach. We show theoretically that, for a sufficiently large sample size and intermediate values of heritability, the two approaches provide similar results. Using the Atherosclerosis Risk in Communities cohort, we show empirically that the two approaches can give different results and that the variance/uncertainty can remain large.

Preparation of Porous Stainless Steel Hollow-Fibers through Multi-Modal Particle Size Sintering towards Pore Engineering

PubMed Central

Allioux, Francois-Marie; Etxeberria Benavides, Miren

2017-01-01

The sintering of metal powders is an efficient and versatile technique to fabricate porous metal elements such as filters, diffusers, and membranes. Neck formation between particles is, however, critical to tune the porosity and optimize mass transfer in order to minimize the densification process. In this work, macro-porous stainless steel (SS) hollow-fibers (HFs) were fabricated by the extrusion and sintering of a dope comprised, for the first time, of a bimodal mixture of SS powders. The SS particles of different sizes and shapes were mixed to increase the neck formation between the particles and control the densification process of the structure during sintering. The sintered HFs from particles of two different sizes were shown to be more mechanically stable at lower sintering temperature due to the increased neck area of the small particles sintered to the large ones. In addition, the sintered HFs made from particles of 10 and 44 μm showed a smaller average pore size (<1 μm) as compared to the micron-size pores of sintered HFs made from particles of 10 μm only and those of 10 and 20 μm. The novel HFs could be used in a range of applications, from filtration modules to electrochemical membrane reactors. PMID:28777352

Particle size distribution properties in mixed-phase monsoon clouds from in situ measurements during CAIPEEX

NASA Astrophysics Data System (ADS)

Patade, Sachin; Prabha, T. V.; Axisa, D.; Gayatri, K.; Heymsfield, A.

2015-10-01

A comprehensive analysis of particle size distributions measured in situ with airborne instrumentation during the Cloud Aerosol Interaction and Precipitation Enhancement Experiment (CAIPEEX) is presented. In situ airborne observations in the developing stage of continental convective clouds during premonsoon (PRE), transition, and monsoon (MON) period at temperatures from 25 to -22°C are used in the study. The PRE clouds have narrow drop size and particle size distributions compared to monsoon clouds and showed less development of size spectra with decrease in temperature. Overall, the PRE cases had much lower values of particle number concentrations and ice water content compared to MON cases, indicating large differences in the ice initiation and growth processes between these cloud regimes. This study provided compelling evidence that in addition to dynamics, aerosol and moisture are important for modulating ice microphysical processes in PRE and MON clouds through impacts on cloud drop size distribution. Significant differences are observed in the relationship of the slope and intercept parameters of the fitted particle size distributions (PSDs) with temperature in PRE and MON clouds. The intercept values are higher in MON clouds than PRE for exponential distribution which can be attributed to higher cloud particle number concentrations and ice water content in MON clouds. The PRE clouds tend to have larger values of dispersion of gamma size distributions than MON clouds, signifying narrower spectra. The relationships between PSDs parameters are presented and compared with previous observations.

Effects of Precipitation on Ocean Mixed-Layer Temperature and Salinity as Simulated in a 2-D Coupled Ocean-Cloud Resolving Atmosphere Model

NASA Technical Reports Server (NTRS)

Li, Xiaofan; Sui, C.-H.; Lau, K-M.; Adamec, D.

1999-01-01

A two-dimensional coupled ocean-cloud resolving atmosphere model is used to investigate possible roles of convective scale ocean disturbances induced by atmospheric precipitation on ocean mixed-layer heat and salt budgets. The model couples a cloud resolving model with an embedded mixed layer-ocean circulation model. Five experiment are performed under imposed large-scale atmospheric forcing in terms of vertical velocity derived from the TOGA COARE observations during a selected seven-day period. The dominant variability of mixed-layer temperature and salinity are simulated by the coupled model with imposed large-scale forcing. The mixed-layer temperatures in the coupled experiments with 1-D and 2-D ocean models show similar variations when salinity effects are not included. When salinity effects are included, however, differences in the domain-mean mixed-layer salinity and temperature between coupled experiments with 1-D and 2-D ocean models could be as large as 0.3 PSU and 0.4 C respectively. Without fresh water effects, the nocturnal heat loss over ocean surface causes deep mixed layers and weak cooling rates so that the nocturnal mixed-layer temperatures tend to be horizontally-uniform. The fresh water flux, however, causes shallow mixed layers over convective areas while the nocturnal heat loss causes deep mixed layer over convection-free areas so that the mixed-layer temperatures have large horizontal fluctuations. Furthermore, fresh water flux exhibits larger spatial fluctuations than surface heat flux because heavy rainfall occurs over convective areas embedded in broad non-convective or clear areas, whereas diurnal signals over whole model areas yield high spatial correlation of surface heat flux. As a result, mixed-layer salinities contribute more to the density differences than do mixed-layer temperatures.

Synthesis of hydroxyapatite nanoparticles by a novel ultrasonic assisted with mixed hollow sphere template method

NASA Astrophysics Data System (ADS)

Gopi, D.; Indira, J.; Kavitha, L.; Sekar, M.; Mudali, U. Kamachi

Hydroxyapatite (HAP) is the main inorganic component of bone material and is widely used in various biomedical applications due to its excellent bioactivity and biocompatibility. In this paper, we have reported the synthesis of hydroxyapatite nanoparticles by a novel ultrasonic assisted mixed template directed method. In this method glycine-acrylic acid (GLY-AA) hollow spheres were used as an organic template which could be prepared by mixing of glycine with acrylic acid. The as-synthesized HAP nanoparticles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM) and tunnelling electron microscope (TEM) to investigate the nature of bonding, crystallinity, size and shape. The thermal stability of as-synthesized nanoparticles was also investigated by the thermo gravimetric analysis (TGA). The effect of ultrasonic irradiation time on the crystallinity and size of the HAP nanoparticles in presence of glycine-acrylic acid hollow spheres template were investigated. From the inspection of the above results it is confirmed that the crystallinity and size of the HAP nanoparticles decrease with increasing ultrasonic irradiation time. Hence the proposed synthesis strategy provides a facile pathway to obtain nano sized HAP with high quality, suitable size and morphology.

Aerosol Indirect Effect on Warm Clouds over Eastern China Using Combined CALIOP and MODIS Observations

NASA Astrophysics Data System (ADS)

Guo, Jianping; Wang, Fu; Huang, Jingfeng; Li, Xiaowen

2015-04-01

Aerosol, one of key components of the climate system, is highly variable, both temporally and spatially. It often exerts great influences on the cloud-precipitation chain processes by serving as CCN/IN, altering cloud microphysics and its life cycle. Yet, the aerosol indirect effect on clouds remains largely unknown, because the initial changes in clouds due to aerosols may be enhanced or dampened by such feedback processes as modified cloud dynamics, or evaporation of the smaller droplets due to the competition for water vapor. In this study, we attempted to quantify the aerosol effects on warm cloud over eastern China, based on near-simultaneous retrievals from MODIS/AQUA, CALIOP/CALIPSO and CPR/CLOUDSAT during the period 2006 to 2010. The seasonality of aerosol from ground-based PM10 is quite different from that estimated from MODIS AOD. This result is corroborated by lower level profile of aerosol occurrence frequency from CALIOP, indicating the significant role CALIOP could play in aerosol-cloud interaction. The combined use of CALIOP and CPR facilitate the process to exactly determine the (vertical) position of warm cloud relative to aerosol, out of six scenarios in terms of aerosol-cloud mixing status in terms of aerosol-cloud mixing status, which shows as follows: AO (Aerosol only), CO (Cloud only), SASC (Single aerosol-single cloud), SADC (single aerosol-double cloud), DASC (double aerosol-single cloud), and others. Results shows that about 54% of all the cases belong to mixed status, among all the collocated aerosol-cloud cases. Under mixed condition, a boomerang shape is observed, i.e., reduced cloud droplet radius (CDR) is associated with increasing aerosol at moderate aerosol pollution (AOD<0.4), becoming saturated at AOD of 0.5, followed by an increase in CDR with aerosol. In contrast, there is no such boomerang shape found for (aerosol-cloud) separated cases. We categorize dataset into warm-season and cold-season subsets to figure out how the boomerang shape varies with season. For moderate aerosol loading (AOD<0.4), the effect on the droplet size for the "Mixed" cases is greater during cold season (denoted by a large slope), as compared with that during warm season. It is likely associated with an increase in the emission of light absorbing aerosol like smoke (black carbon), mainly caused by coal-fired heating during the cold season in China. As expected, the sensitivity of CDR to AOD is much weaker for "Separated" cases, irrespective of warm or cold seasons, indicating no real aerosol indirect effect occurring in this case. In contrast, for heavy aerosol loading (AOD>0.4), an increasing CDR with AOD can be seen in "Mixed" scenario during the warm season. Conversely, a closer look at the responses of CDR during the cold season shows that CDR decreases with AOD, although the strength is not much large. Therefore, we argue that cloud droplet size decreases with aerosol loading during cold season, irrespective of moderate or heavy atmospheric pollution. Finally, we discuss the possible factors that may influence the aerosol indirect effects on warm clouds investigated here. For instance, aerosol-cloud interaction conundrum might be affected by aerosol humidification, which is the case for MODIS AOD during warm seasons. But this issue can be partly overcome by categorizing dataset into warm-season and cold-season subsets, representing different ambient humidity condition in the atmosphere. The different boomerang shapes observed during various seasons, particularly after transition zone due to droplet saturation effect, have great implications for climate forcing by aerosol in eastern China.

The crustal magma storage system of Volcán Quizapu, Chile, and the effects of magma mixing on magma diversity

USGS Publications Warehouse

Bergantz, George W.; Cooper, Kari M.; Hildreth, Edward; Ruprecht, Phillipp

2012-01-01

Crystal zoning as well as temperature and pressure estimates from phenocryst phase equilibria are used to constrain the architecture of the intermediate-sized magmatic system (some tens of km3) of Volcán Quizapu, Chile, and to document the textural and compositional effects of magma mixing. In contrast to most arc magma systems, where multiple episodes of open-system behavior obscure the evidence of major magma chamber events (e.g. melt extraction, magma mixing), the Quizapu magma system shows limited petrographic complexity in two large historical eruptions (1846–1847 and 1932) that have contrasting eruptive styles. Quizapu magmas and peripheral mafic magmas exhibit a simple binary mixing relationship. At the mafic end, basaltic andesite to andesite recharge magmas complement the record from peripheral cones and show the same limited range of compositions. The silicic end-member composition is almost identical in both eruptions of Quizapu. The effusive 1846–1847 eruption records significant mixing between the mafic and silicic end-members, resulting in hybridized andesites and mingled dacites. These two compositionally simple eruptions at Volcán Quizapu present a rare opportunity to isolate particular aspects of magma evolution—formation of homogeneous dacite magma and late-stage magma mixing—from other magma chamber processes. Crystal zoning, trace element compositions, and crystal-size distributions provide evidence for spatial separation of the mafic and silicic magmas. Dacite-derived plagioclase phenocrysts (i.e. An25–40) show a narrow range in composition and limited zonation, suggesting growth from a compositionally restricted melt. Dacite-derived amphibole phenocrysts show similar restricted compositions and furthermore constrain, together with more mafic amphibole phenocrysts, the architecture of the magmatic system at Volcán Quizapu to be compositionally and thermally zoned, in which an andesitic mush is overlain by a homogeneous dacitic magma that is the source for most of the 1846–1847 and 1932 erupted magmas. Dacite formation is best explained by mineral–melt separation (crystal fractionation) from an andesitic mush, which is inferred to have thermally and compositionally buffered the dacite magma thereby keeping it at relatively low crystallinity (<30 vol. %). The dominant cause of compositional diversity is melt separation. Back-mixing of mush (i.e. crystals with signatures of growth both in the andesitic mush and in the dacite magma) into the overlying dacite magma is rarely observed. Recharge events that increase crystal and magma diversity in the dacite magma are limited to an episode of mafic recharge and mixing just prior to the 1846–1847 eruption, where evidence for magma mixing is present on all scales. Chamber-wide mixing was incomplete (mixing efficiency of ∼0·53–0·85) as flow lobes vary significantly in composition along the proposed mixing array. Estimates of viscosity variations during the course of magma mixing suggest that mixing dynamics and the degree of magma interaction on all scales were established at the beginning of the recharge event.

The impact of microfluidic mixing of triblock micelleplexes on in vitro / in vivo gene silencing and intracellular trafficking

NASA Astrophysics Data System (ADS)

Feldmann, Daniel P.; Xie, Yuran; Jones, Steven K.; Yu, Dongyue; Moszczynska, Anna; Merkel, Olivia M.

2017-06-01

The triblock copolymer polyethylenimine-polycaprolactone-polyethylene glycol (PEI-PCL-PEG) has been shown to spontaneously assemble into nano-sized particulate carriers capable of complexing with nucleic acids for gene delivery. The objective of this study was to investigate micelleplex characteristics, their in vitro and in vivo fate following microfluidic preparation of siRNA nanoparticles compared to the routinely used batch reactor mixing technique. Herein, PEI-PCL-PEG nanoparticles were prepared with batch reactor or microfluidic mixing techniques and characterized by various biochemical assays and in cell culture. Microfluidic nanoparticles showed a reduction of overall particle size as well as a more uniform size distribution when compared to batch reactor pipette mixing. Confocal microscopy, flow cytometry and qRT-PCR displayed the subcellular delivery of the microfluidic formulation and confirmed the ability to achieve mRNA knockdown. Intratracheal instillation of microfluidic formulation resulted in a significantly more efficient (p < 0.05) knockdown of GAPDH compared to treatment with the batch reactor formulation. The use of microfluidic mixing techniques yields an overall smaller and more uniform PEG-PCL-PEI nanoparticle that is able to more efficiently deliver siRNA in vivo. This preparation method may prove to be useful when a scaled up production of well-defined polyplexes is required.

A Mixed Micelle Formulation for Oral Delivery of Vitamin K.

PubMed

Sun, Feilong; Jaspers, Tessa C C; van Hasselt, Peter M; Hennink, Wim E; van Nostrum, Cornelus F

2016-09-01

To develop a stable micellar formulation of vitamin K for oral delivery, because the commercial and clinically used formulation of vitamin K (Konakion® MM) destabilizes at gastric pH resulting in low bioavailability of this vitamin in neonates with cholestasis. Mixed micelles composed of EPC, DSPE-PEG 2000 and glycocholic acid, with and without vitamin K, were prepared by a film hydration method. The influence of pH on the stability of the micelles was analyzed by dynamic light scattering (DLS). The critical micelle concentration (CMC) was determined by fluorescence spectroscopy using pyrene and the morphology was evaluated by transmission electron microscopy . Caco-2 cells were used to study the cytocompatibilty. Mixed micelles with mean diameters from 7.1 to 11.0 nm and a narrow size distribution (PDI < 0.2) were obtained after 3 membrane extrusion cycles. Konakion® MM formed aggregated particles at gastric pH, which was avoided through steric stabilization by introducing PEG. TEM showed that mixed micelles had a spherical size (diameter of around 10 nm) with a narrow size distribution in agreement with the DLS results. The loading capacities for vitamin K of mixed micelles with varying molar fractions of DSPE-PEG and EPC (from 0/100 to 50/50 (mol/mol)) were 10.8-5.0 w%, respectively. The mixed micelles showed good cytocompatibility at concentrations of glycocholic acid between 0.12 and 1.20 mM. Mixed micelles with superior stability to Konakion® MM at low pH were obtained by introducing DSPE-PEG 2000. These are therefore attractive oral formulations for vitamin K.

Inferred Primary Compositions of Archean Spherules Formed by the Condensation of an Impact-produced Rock Vapor Cloud, Barberton Greenstone Belt, South Africa

NASA Technical Reports Server (NTRS)

Krull, A. E.; Lowe, D. R.; Byerly, G. R.

2003-01-01

Based on the lunar cratering record, impacts were larger and more frequent on the early Earth than they are today. There is no persevered record of these early terrestrial impacts because rocks of this age have been obliterated by tectonism and erosion. The oldest known evidence of impacts on Earth lies in four beds (S1, S2, S3 and S4) in the Barberton Greenstone Belt (BGB), South Africa, ranging in age from about 3.24 to 3.47 Ga. These beds are composed in large part of sand-sized spherical particles, termed spherules, that are thought to have formed by the condensation of rock vapor clouds ejected above the atmosphere as a result of large impacts. Spherule beds S2 and S3 are both about 20 cm thick where composed entirely of fall-deposited spherules and up to a meter thick where spherules are mixed with locally derived debris. The diameters the bolides have been estimated to be between 20 and 50 km, based on bed thickness, size of the largest spherules, Ir fluence and extraterrestrial Cr.

Free flux flow in two single crystals of V3Si with differing pinning strengths

NASA Astrophysics Data System (ADS)

Gafarov, O.; Gapud, A. A.; Moraes, S.; Thompson, J. R.; Christen, D. K.; Reyes, A. P.

2011-10-01

Results of measurements on two very clean, single-crystal samples of the A15 superconductor V3Si are presented. Magnetization and transport data have confirmed the ``clean'' quality of both samples, as manifested by: (i) high residual electrical resistivity ratio, (ii) very low critical current densities Jc, and (iii) a ``peak'' effect in the field dependence of critical current. The (H,T) phase line for this peak effect is shifted down for the slightly ``dirtier'' sample, which consequently also has higher critical current density Jc(H). Large Lorentz forces are applied on mixed-state vortices via large currents, in order to induce the highly ordered free flux flow (FFF) phase, using experimental methods developed previously. The traditional model by Bardeen and Stephen (BS) predicts a simple field dependence of flux flow resistivity ρf(H) ˜ H/Hc2, presuming a field-independent flux core size. A model by Kogan and Zelezhina (KZ) takes into account the effects of magnetic field on core size, and predict a clear deviation from the linear BS dependence. In this study, ρf(H) is confirmed to be consistent with predictions of KZ.

Turbulent Concentration of mm-Size Particles in the Protoplanetary Nebula: Scale-Dependent Cascades

NASA Technical Reports Server (NTRS)

Cuzzi, J. N.; Hartlep, T.

2015-01-01

The initial accretion of primitive bodies (here, asteroids in particular) from freely-floating nebula particles remains problematic. Traditional growth-by-sticking models encounter a formidable "meter-size barrier" (or even a mm-to-cm-size barrier) in turbulent nebulae, making the preconditions for so-called "streaming instabilities" difficult to achieve even for so-called "lucky" particles. Even if growth by sticking could somehow breach the meter size barrier, turbulent nebulae present further obstacles through the 1-10km size range. On the other hand, nonturbulent nebulae form large asteroids too quickly to explain long spreads in formation times, or the dearth of melted asteroids. Theoretical understanding of nebula turbulence is itself in flux; recent models of MRI (magnetically-driven) turbulence favor low-or- no-turbulence environments, but purely hydrodynamic turbulence is making a comeback, with two recently discovered mechanisms generating robust turbulence which do not rely on magnetic fields at all. An important clue regarding planetesimal formation is an apparent 100km diameter peak in the pre-depletion, pre-erosion mass distribution of asteroids; scenarios leading directly from independent nebula particulates to large objects of this size, which avoid the problematic m-km size range, could be called "leapfrog" scenarios. The leapfrog scenario we have studied in detail involves formation of dense clumps of aerodynamically selected, typically mm-size particles in turbulence, which can under certain conditions shrink inexorably on 100-1000 orbit timescales and form 10-100km diameter sandpile planetesimals. There is evidence that at least the ordinary chondrite parent bodies were initially composed entirely of a homogeneous mix of such particles. Thus, while they are arcane, turbulent concentration models acting directly on chondrule size particles are worthy of deeper study. The typical sizes of planetesimals and the rate of their formation can be estimated using a statistical model with properties inferred from large numerical simulations of turbulence. Nebula turbulence is described by its Reynolds number Re = (L/eta)(exp 4/3), where L = H alpha(exp 1/2) is the largest eddy scale, H is the nebula gas vertical scale height, alpha the turbulent viscosity parameter, and eta is the Kolmogorov or smallest scale in turbulence (typically about 1km), with eddy turnover time t(sub eta). In the nebula, Re is far larger than any numerical simulation can handle, so some physical arguments are needed to extend the results of numerical simulations to nebula conditions. In this paper, we report new physics to be incorporated into our statistical models.

Composition, structure and properties of sediment thermal springs of Kamchatka

NASA Astrophysics Data System (ADS)

Shanina, Violetta; Smolyakov, Pavel; Parfenov, Oleg

2016-04-01

The paper deals with the physical and mechanical properties sediment thermal fields Mutnovsky, Lower Koshelevo and Bannyh (Kamchatka). This multi-component soils, mineral and chemical composition of which depends on the formation factors (pH, temperature, salinity of water, composition and structure of the host volcanic rocks). Samples Lower Koshelevo sediment thermal sources differ in the following composition: smectite, kaolinite, kaolinite-smectite mixed-mineral. Samples of sediment thermal springs Mutnovsky volcano in accordance with the X-ray analysis has the following composition: volcanic glass, crystalline sulfur, plagioclase, smectite, illite-smectite mixed, illite, chlorite, quartz, cristobalite, pyrite, melanterite, kaolinite. Natural moisture content samples of sediment thermal springs from 45 to 121%, hygroscopic moisture content of 1.3 to 3.7%. A large amount of native sulfur (up to 92%) and the presence of amorphous material gives low values of density of solid particles (up to 2.1 g/cm3) samples Mutnovskii thermal field. The values of the density of solids sediment Koshelevo and Bannyh hot springs close to those of the main components of mineral densities (up to 2.6-3.0 g/cm3). The results of the particle size distribution and microaggregate analysis of sediment thermal springs Lower Koshelevo field shows that the predominance observed of particles with a diameter from 0.05 mm to 0.25 mm, the coefficient of soil heterogeneity heterogeneous. In the bottom sediments of the thermal springs of the volcano Mutnovsky poorly traced predominance of one faction. Most prevalent fraction with particle size 0.01 - 0.05 mm. When analyzing the content in the soil microaggregates their content is shifted towards particles with a diameter of 0.25 mm. The contents of a large number of large (1-10 mm), porous rock fragments, due to the deposition of pyroclastic material from the eruptions of the last century. Present in large amounts rounded crystals of native sulfur associated with the rise of mixed solutions, formed at the boundary of secondary boil through faults to the surface thermal boiler (Bortnikova et al., 2009). Calculated flow index and plasticity, shows the classification in accordance with GOST 25100-2011. From these figures it is clear that all the sediments are sandy loam and are in a fluid state. A clear relationship between temperature, pH and particle size distribution of sediment thermal springs can not be traced, great importance is the geological evolution of the volcanic activity, hydrogeological conditions and the time factor. Therefore, samples with a currently active Mutnovsky volcano - sandy loam, sediments of the thermal springs Koshelevo fields are often to loams. The bottom sediments of thermal springs from the territory of the Lower Koshelevo thermal field in a natural occurrence in a state of higher yield strength, so they are an unstable surface, which may cause landslides. The bottom sediments of thermal springs are low explored subject of engineering geology, it is important to examine their properties to simulate the conditions of formation and the development of dangerous processes.

Mixed sediment beach processes: Kachemak Bay, Alaska

USGS Publications Warehouse

Ruggiero, P.; Adams, P.N.; Warrick, J.A.

2007-01-01

Mixed sediment beaches are morphologically distinct from and more complex than either sand or gravel only beaches. Three digital imaging techniques are employed to quantify surficial grain size and bedload sediment transport rates along the mixed sediment beaches of Kachemak Bay, Alaska. Applying digital imaging procedures originally developed for quickly and efficiently quantifying grain sizes of sand to coarse sediment classes gives promising results. Hundreds of grain size estimates lead to a quantitative characterization of the region's sediment at a significant reduction in cost and time as compared to traditional techniques. Both the sand and coarse fractions on this megatidal beach mobilize into self-organized bedforms that migrate alongshore with a seasonally reflecting the temporal pattern of the alongshore component of wave power. In contrast, the gravel bedforms also migrate in the cross-shore without significant seasonally suggesting that swash asymmetry is sufficient to mobilize the gravel even during low energy summer conditions. ?? 2007 ASCE.

Implications of fractured Arctic perennial ice cover on thermodynamic and dynamic sea ice processes

NASA Astrophysics Data System (ADS)

Asplin, Matthew G.; Scharien, Randall; Else, Brent; Howell, Stephen; Barber, David G.; Papakyriakou, Tim; Prinsenberg, Simon

2014-04-01

Decline of the Arctic summer minimum sea ice extent is characterized by large expanses of open water in the Siberian, Laptev, Chukchi, and Beaufort Seas, and introduces large fetch distances in the Arctic Ocean. Long waves can propagate deep into the pack ice, thereby causing flexural swell and failure of the sea ice. This process shifts the floe size diameter distribution smaller, increases floe surface area, and thereby affects sea ice dynamic and thermodynamic processes. The results of Radarsat-2 imagery analysis show that a flexural fracture event which occurred in the Beaufort Sea region on 6 September 2009 affected ˜40,000 km2. Open water fractional area in the area affected initially decreased from 3.7% to 2.7%, but later increased to ˜20% following wind-forced divergence of the ice pack. Energy available for lateral melting was assessed by estimating the change in energy entrainment from longwave and shortwave radiation in the mixed-layer of the ocean following flexural fracture. 11.54 MJ m-2 of additional energy for lateral melting of ice floes was identified in affected areas. The impact of this process in future Arctic sea ice melt seasons was assessed using estimations of earlier occurrences of fracture during the melt season, and is discussed in context with ocean heat fluxes, atmospheric mixing of the ocean mixed layer, and declining sea ice cover. We conclude that this process is an important positive feedback to Arctic sea ice loss, and timing of initiation is critical in how it affects sea ice thermodynamic and dynamic processes.

Design and methodology of a mixed methods follow-up study to the 2014 Ghana Demographic and Health Survey

PubMed Central

Staveteig, Sarah; Aryeetey, Richmond; Anie-Ansah, Michael; Ahiadeke, Clement; Ortiz, Ladys

2017-01-01

ABSTRACT Background: The intended meaning behind responses to standard questions posed in large-scale health surveys are not always well understood. Systematic follow-up studies, particularly those which pose a few repeated questions followed by open-ended discussions, are well positioned to gauge stability and consistency of data and to shed light on the intended meaning behind survey responses. Such follow-up studies require extensive coordination and face challenges in protecting respondent confidentiality during the process of recontacting and reinterviewing participants. Objectives: We describe practical field strategies for undertaking a mixed methods follow-up study during a large-scale health survey. Methods: The study was designed as a mixed methods follow-up study embedded within the 2014 Ghana Demographic and Health Survey (GDHS). The study was implemented in 13 clusters. Android tablets were used to import reference data from the parent survey and to administer the questionnaire, which asked a mixture of closed- and open-ended questions on reproductive intentions, decision-making, and family planning. Results: Despite a number of obstacles related to recontacting respondents and concern about respondent fatigue, over 92 percent of the selected sub-sample were successfully recontacted and reinterviewed; all consented to audio recording. A confidential linkage between GDHS data, follow-up tablet data, and audio transcripts was successfully created for the purpose of analysis. Conclusions: We summarize the challenges in follow-up study design, including ethical considerations, sample size, auditing, filtering, successful use of tablets, and share lessons learned for future such follow-up surveys. PMID:28145817

Freeze-thaw cycles induce content exchange between cell-sized lipid vesicles

NASA Astrophysics Data System (ADS)

Litschel, Thomas; Ganzinger, Kristina A.; Movinkel, Torgeir; Heymann, Michael; Robinson, Tom; Mutschler, Hannes; Schwille, Petra

2018-05-01

Early protocells are commonly assumed to consist of an amphiphilic membrane enclosing an RNA-based self-replicating genetic system and a primitive metabolism without protein enzymes. Thus, protocell evolution must have relied on simple physicochemical self-organization processes within and across such vesicular structures. We investigate freeze-thaw (FT) cycling as a potential environmental driver for the necessary content exchange between vesicles. To this end, we developed a conceptually simple yet statistically powerful high-throughput procedure based on nucleic acid-containing giant unilamellar vesicles (GUVs) as model protocells. GUVs are formed by emulsion transfer in glass bottom microtiter plates and hence can be manipulated and monitored by fluorescence microscopy without additional pipetting and sample handling steps. This new protocol greatly minimizes artefacts, such as unintended GUV rupture or fusion by shear forces. Using DNA-encapsulating phospholipid GUVs fabricated by this method, we quantified the extent of content mixing between GUVs under different FT conditions. We found evidence of nucleic acid exchange in all detected vesicles if fast freezing of GUVs at ‑80 °C is followed by slow thawing at room temperature. In contrast, slow freezing and fast thawing both adversely affected content mixing. Surprisingly, and in contrast to previous reports for FT-induced content mixing, we found that the content is not exchanged through vesicle fusion and fission, but that vesicles largely maintain their membrane identity and even large molecules are exchanged via diffusion across the membranes. Our approach supports efficient screening of prebiotically plausible molecules and environmental conditions, to yield universal mechanistic insights into how cellular life may have emerged.

Relation between climatic factors, diet and reproductive parameters of Little Terns over a decade

NASA Astrophysics Data System (ADS)

Ramos, Jaime A.; Pedro, Patrícia; Matos, Antonio; Paiva, Vitor H.

2013-11-01

We used 10 years of data on clutch size, egg size and diet, and 8 years of data on timing of laying on Little Terns (Sternula albifrons) breeding in Ria Formosa lagoon system, Algarve, Portugal to assess whether diet acts as an important intermediary between climatic conditions and breeding parameters. We used Generalized Linear Models to relate (1) the relative occurrence and size of the main prey species, sand smelts (Atherina spp.), with environmental variables, a large-scale climate variable, the North Atlantic Oscillation (NAO) index, and a local scale variable, the sea-surface temperature (SST), and (2) the respective effects of sand smelts relative occurrence, NAO index and SST on Little Tern breeding parameters. The diet of Little Terns was dominated by sand smelts, with a frequency occurrence of over 60% in all years. The winter SST (February) was negatively associated with the relative occurrence of sand smelts in the diet of Little Terns during the breeding season which, in turn, was positively associated with Little Tern clutch size. Our results suggest that negative NAO conditions in the Atlantic Ocean, often associated with rougher sea conditions (greater vertical mixing, stronger winds and lower SST) were related with earlier breeding, and lower SST in the surroundings of the colony during winter-spring favour the abundance of prey fish for Little Terns as well as their reproductive parameters. Climate patterns at both large and local scales are likely to change in the future, which may have important implications for estuarine seabirds in Southern Europe.

Characterization of Ze and LDR of nonspherical and inhomogeneous ice particles for 95-GHz cloud radar: Its implication to microphysical retrievals

NASA Astrophysics Data System (ADS)

Sato, Kaori; Okamoto, Hajime

2006-11-01

Effect of density, shape, and orientation on radar reflectivity factor (Ze) and linear depolarization ratio (LDR) at 95 GHz are investigated by using the discrete dipole approximation (DDA) for ice cloud studies. We consider hexagonal plate, hollow hexagonal column, and hollow bullet rosette in horizontal (2-D) or three-dimensional (3-D) random orientation. We first validate a widely used method to take into account the density and shape effects by the combinational use of Mie theory with the Maxwell-Garnett mixing rule (the MG-Mie method). It is found that the MG-Mie method underestimates Ze and its applicability is limited to sizes smaller than 40 μm. On the basis of the DDA, it is possible to separately treat density, aspect ratio, orientation, and shape. Effect of density turns out to be minor. Orientation and shape are the major controlling factors for Ze especially at effective radius reff > 100 μm and LDR except for very large sizes where the effect of orientation in LDR diminishes. Comparison between the DDA results and the analytical solution for 3-D Rayleigh spheroids show that LDR in the small size range is characterized by the target boundary and aspect ratio. In the large size range, LDR reveals features of a single target element; for example, LDR of bullet rosette is similar to that of a single branch of the particle. Combinational use of Ze and LDR is effective in microphysics retrieval for LDR < -23 dB. For LDR > -23 dB, additional information such as Doppler velocity is required.

Large Area and Short-Pulse Shock Initiation of a Tatb/hmx Mixed Explosive

NASA Astrophysics Data System (ADS)

Guiji, Wang; Chengwei, Sun; Jun, Chen; Cangli, Liu; Jianheng, Zhao; Fuli, Tan; Ning, Zhang

2007-12-01

The large area and short-pulse shock initiation experiments on the plastic bonded mixed explosive of TATB(80%) and HMX(15%) have been performed with an electric gun where a Mylar flyer of 10-19 mm in diameter and 0.05˜0.30 mm in thickness was launched by an electrically exploding metallic bridge foil. The cylindrical explosive specimens (Φ16 mm×8 mm in size) were initiated by the Mylar flyers in thickness of 0.07˜0.20 mm, which induced shock pressure in specimen was of duration ranging from 0.029 to 0.109 μs. The experimental data were treated with the DRM(Delayed Robbins-Monro) procedure and to provide the initiation threshold of flyer velocities at 50% probability are 3.398˜1.713 km/s and that of shock pressure P 13.73˜5.23 GPa, respectively for different pulse durations. The shock initiation criteria of the explosive specimen at 50% and 100% probabilities are yielded. In addition, the 30° wedged sample was tested and the shock to detonation transition (SDT) process emerging on its inclined surface was diagnosed with a device consisting of multiple optical fiber probe, optoelectronic transducer and digital oscilloscope. The POP plot of the explosive has been gained from above SDT data.

Comparision on dynamic behavior of diesel spray and rapeseed oil spray in diesel engine

NASA Astrophysics Data System (ADS)

Sapit, Azwan; Azahari Razali, Mohd; Faisal Hushim, Mohd; Jaat, Norrizam; Nizam Mohammad, Akmal; Khalid, Amir

2017-04-01

Fuel-air mixing is important process in diesel combustion. It significantly affects the combustion and emission of diesel engine. Biomass fuel has high viscosity and high distillation temperature and may negatively affect the fuel-air mixing process. Thus, study on the spray development and atomization of this type of fuel is important. This study investigates the atomization characteristics and droplet dynamic behaviors of diesel engine spray fuelled by rapeseed oil (RO) and comparison to diesel fuel (GO). Optical observation of RO spray was carried out using shadowgraph photography technique. Single nano-spark photography technique was used to study the characteristics of the spray while dual nano-spark shadowgraph technique was used to study the spray droplet behavior. Using in-house image processing algorithm, the images were processed and the boundary condition of each spray was also studied. The results show that RO has very poor atomization due to the high viscosity nature of the fuel when compared to GO. This is in agreement with the results from spray droplet dynamic behavior studies that shows due to the high viscosity, the RO spray droplets are large in size and travel downward, with very little influence of entrainment effect due to its large kinematic energy.

New Evidence on Self-Affirmation Effects and Theorized Sources of Heterogeneity from Large-Scale Replications

PubMed Central

Hanselman, Paul; Rozek, Christopher S.; Grigg, Jeffrey; Borman, Geoffrey D.

2016-01-01

Brief, targeted self-affirmation writing exercises have recently been offered as a way to reduce racial achievement gaps, but evidence about their effects in educational settings is mixed, leaving ambiguity about the likely benefits of these strategies if implemented broadly. A key limitation in interpreting these mixed results is that they come from studies conducted by different research teams with different procedures in different settings; it is therefore impossible to isolate whether different effects are the result of theorized heterogeneity, unidentified moderators, or idiosyncratic features of the different studies. We addressed this limitation by conducting a well-powered replication of self-affirmation in a setting where a previous large-scale field experiment demonstrated significant positive impacts, using the same procedures. We found no evidence of effects in this replication study and estimates were precise enough to reject benefits larger than an effect size of 0.10. These null effects were significantly different from persistent benefits in the prior study in the same setting, and extensive testing revealed that currently theorized moderators of self-affirmation effects could not explain the difference. These results highlight the potential fragility of self-affirmation in educational settings when implemented widely and the need for new theory, measures, and evidence about the necessary conditions for self-affirmation success. PMID:28450753

Exact extreme-value statistics at mixed-order transitions.

PubMed

Bar, Amir; Majumdar, Satya N; Schehr, Grégory; Mukamel, David

2016-05-01

We study extreme-value statistics for spatially extended models exhibiting mixed-order phase transitions (MOT). These are phase transitions that exhibit features common to both first-order (discontinuity of the order parameter) and second-order (diverging correlation length) transitions. We consider here the truncated inverse distance squared Ising model, which is a prototypical model exhibiting MOT, and study analytically the extreme-value statistics of the domain lengths The lengths of the domains are identically distributed random variables except for the global constraint that their sum equals the total system size L. In addition, the number of such domains is also a fluctuating variable, and not fixed. In the paramagnetic phase, we show that the distribution of the largest domain length l_{max} converges, in the large L limit, to a Gumbel distribution. However, at the critical point (for a certain range of parameters) and in the ferromagnetic phase, we show that the fluctuations of l_{max} are governed by novel distributions, which we compute exactly. Our main analytical results are verified by numerical simulations.

Nanoparticulate-catalyzed oxygen transfer processes

DOEpatents

Hunt, Andrew T [Atlanta, GA; Breitkopf, Richard C [Dunwoody, GA

2009-12-01

Nanoparticulates of oxygen transfer materials that are oxides of rare earth metals, combinations of rare earth metals, and combinations of transition metals and rare earth metals are used as catalysts in a variety of processes. Unexpectedly large thermal efficiencies are achieved relative to micron sized particulates. Processes that use these catalysts are exemplified in a multistage reactor. The exemplified reactor cracks C6 to C20 hydrocarbons, desulfurizes the hydrocarbon stream and reforms the hydrocarbons in the stream to produce hydrogen. In a first reactor stage the steam and hydrocarbon are passed through particulate mixed rare earth metal oxide to crack larger hydrocarbon molecules. In a second stage, the steam and hydrocarbon are passed through particulate material that desulfurizes the hydrocarbon. In a third stage, the hydrocarbon and steam are passed through a heated, mixed transition metal/rare earth metal oxide to reform the lower hydrocarbons and thereby produce hydrogen. Stages can be alone or combined. Parallel reactors can provide continuous reactant flow. Each of the processes can be carried out individually.

Device for preparing combinatorial libraries in powder metallurgy.

PubMed

Yang, Shoufeng; Evans, Julian R G

2004-01-01

This paper describes a powder-metering, -mixing, and -dispensing mechanism that can be used as a method for producing large numbers of samples for metallurgical evaluation or electrical or mechanical testing from multicomponent metal and cermet powder systems. It is designed to make use of the same commercial powders that are used in powder metallurgy and, therefore, to produce samples that are faithful to the microstructure of finished products. The particle assemblies produced by the device could be consolidated by die pressing, isostatic pressing, laser sintering, or direct melting. The powder metering valve provides both on/off and flow rate control of dry powders in open capillaries using acoustic vibration. The valve is simple and involves no relative movement, avoiding seizure with fine powders. An orchestra of such valves can be arranged on a building platform to prepare multicomponent combinatorial libraries. As with many combinatorial devices, identification and evaluation of sources of mixing error as a function of sample size is mandatory. Such an analysis is presented.

Self-mixing interferometry as a diagnostics tool for plasma characteristics in laser microdrilling

NASA Astrophysics Data System (ADS)

Colombo, Paolo; Demir, Ali Gökhan; Norgia, Michele; Previtali, Barbara

2017-05-01

In this work, self-mixing interferometry (SMI) was used to monitor the optical path difference induced by the ablation plasma and plume. The paper develops the analytical relationships to explain the fringe appearance in the SMI during laser microdrilling. The monitoring principle was tested under a large experimental campaign of laser microdrilling on TiAlN ceramic coating with a low-ns green fibre laser. Key process parameters namely pulse energy, number and repetition rate were varied. The effect of side gas on the SMI signal characteristic was analysed. Laser induced breakdown spectroscopy (LIBS) was used to identify the plasma temperature and electron number density. The SMI signals were correlated to the plume size and its evolution as a function of process parameters, as well as electron number density estimated by spectroscopy. In addition to proving the validity of the proposed new method, the results show insights to the micromachining of the ceramic material with low ns pulses.

On the relevance of chaos for halo stars in the solar neighbourhood II

NASA Astrophysics Data System (ADS)

Maffione, Nicolas P.; Gómez, Facundo A.; Cincotta, Pablo M.; Giordano, Claudia M.; Grand, Robert J. J.; Marinacci, Federico; Pakmor, Rüdiger; Simpson, Christine M.; Springel, Volker; Frenk, Carlos S.

2018-05-01

In a previous paper based on dark matter only simulations we show that, in the approximation of an analytic and static potential describing the strongly triaxial and cuspy shape of Milky Way-sized haloes, diffusion due to chaotic mixing in the neighbourhood of the Sun does not efficiently erase phase space signatures of past accretion events. In this second paper we further explore the effect of chaotic mixing using multicomponent Galactic potential models and solar neighbourhood-like volumes extracted from fully cosmological hydrodynamic simulations, thus naturally accounting for the gravitational potential associated with baryonic components, such as the bulge and disc. Despite the strong change in the global Galactic potentials with respect to those obtained in dark matter only simulations, our results confirm that a large fraction of halo particles evolving on chaotic orbits exhibit their chaotic behaviour after periods of time significantly larger than a Hubble time. In addition, significant diffusion in phase space is not observed on those particles that do exhibit chaotic behaviour within a Hubble time.

A Place-Oriented, Mixed-Level Regionalization Method for Constructing Geographic Areas in Health Data Dissemination and Analysis

PubMed Central

Mu, Lan; Wang, Fahui; Chen, Vivien W.; Wu, Xiao-Cheng

2015-01-01

Similar geographic areas often have great variations in population size. In health data management and analysis, it is desirable to obtain regions of comparable population by decomposing areas of large population (to gain more spatial variability) and merging areas of small population (to mask privacy of data). Based on the Peano curve algorithm and modified scale-space clustering, this research proposes a mixed-level regionalization (MLR) method to construct geographic areas with comparable population. The method accounts for spatial connectivity and compactness, attributive homogeneity, and exogenous criteria such as minimum (and approximately equal) population or disease counts. A case study using Louisiana cancer data illustrates the MLR method and its strengths and limitations. A major benefit of the method is that most upper level geographic boundaries can be preserved to increase familiarity of constructed areas. Therefore, the MLR method is more human-oriented and place-based than computer-oriented and space-based. PMID:26251551

Microfluidic based high throughput synthesis of lipid-polymer hybrid nanoparticles with tunable diameters

PubMed Central

Feng, Qiang; Zhang, Lu; Liu, Chao; Li, Xuanyu; Hu, Guoqing; Sun, Jiashu; Jiang, Xingyu

2015-01-01

Core-shell hybrid nanoparticles (NPs) for drug delivery have attracted numerous attentions due to their enhanced therapeutic efficacy and good biocompatibility. In this work, we fabricate a two-stage microfluidic chip to implement a high-throughput, one-step, and size-tunable synthesis of mono-disperse lipid-poly (lactic-co-glycolic acid) NPs. The size of hybrid NPs is tunable by varying the flow rates inside the two-stage microfluidic chip. To elucidate the mechanism of size-controllable generation of hybrid NPs, we observe the flow field in the microchannel with confocal microscope and perform the simulation by a numerical model. Both the experimental and numerical results indicate an enhanced mixing effect at high flow rate, thus resulting in the assembly of small and mono-disperse hybrid NPs. In vitro experiments show that the large hybrid NPs are more likely to be aggregated in serum and exhibit a lower cellular uptake efficacy than the small ones. This microfluidic chip shows great promise as a robust platform for optimization of nano drug delivery system. PMID:26180574

Ionic Liquids as the MOFs/Polymer Interfacial Binder for Efficient Membrane Separation.

PubMed

Lin, Rijia; Ge, Lei; Diao, Hui; Rudolph, Victor; Zhu, Zhonghua

2016-11-23

Obtaining strong interfacial affinity between filler and polymer is critical to the preparation of mixed matrix membranes (MMMs) with high separation efficiency. However, it is still a challenge for micron-sized metal organic frameworks (MOFs) to achieve excellent compatibility and defect-free interface with polymer matrix. Thin layer of ionic liquid (IL) was immobilized on micron-sized HKUST-1 to eliminate the interfacial nonselective voids in MMMs with minimized free ionic liquid (IL) in polymer matrix, and then the obtained IL decorated HKUST-1 was incorporated into 4,4'-(hexafluoroisopropylidene)diphthalic anhydride-2,3,5,6-tetramethyl-1,3-phenyldiamine (6FDA-Durene) to fabricate MMMs. Acting as a filler/polymer interfacial binder, the favorable MOF/IL and IL/polymer interaction can facilitate the enhancement of MOF/polymer affinity. Compared to MMM with only HKUST-1 incorporation, MMM with IL decorated HKUST-1 succeeded in restricting the formation of nonselective interfacial voids, leading to an increment in CO 2 selectivity. The IL decoration method can be an effective approach to eliminate interfacial voids in MMMs, extending the filler selection to a wide range of large-sized fillers.

Effects of morphological Family Size for young readers.

PubMed

Perdijk, Kors; Schreuder, Robert; Baayen, R Harald; Verhoeven, Ludo

2012-09-01

Dutch children, from the second and fourth grade of primary school, were each given a visual lexical decision test on 210 Dutch monomorphemic words. After removing words not recognized by a majority of the younger group, (lexical) decisions were analysed by mixed-model regression methods to see whether morphological Family Size influenced decision times over and above several other covariates. The effect of morphological Family Size on decision time was mixed: larger families led to significantly faster decision times for the second graders but not for the fourth graders. Since facilitative effects on decision times had been found for adults, we offer a developmental account to explain the absence of an effect of Family Size on decision times for fourth graders. ©2011 The British Psychological Society.

Impact of oceanic-scale interactions on the seasonal modulation of ocean dynamics by the atmosphere.

PubMed

Sasaki, Hideharu; Klein, Patrice; Qiu, Bo; Sasai, Yoshikazu

2014-12-15

Ocean eddies (with a size of 100-300 km), ubiquitous in satellite observations, are known to represent about 80% of the total ocean kinetic energy. Recent studies have pointed out the unexpected role of smaller oceanic structures (with 1-50 km scales) in generating and sustaining these eddies. The interpretation proposed so far invokes the internal instability resulting from the large-scale interaction between upper and interior oceanic layers. Here we show, using a new high-resolution simulation of the realistic North Pacific Ocean, that ocean eddies are instead sustained by a different process that involves small-scale mixed-layer instabilities set up by large-scale atmospheric forcing in winter. This leads to a seasonal evolution of the eddy kinetic energy in a very large part of this ocean, with an amplitude varying by a factor almost equal to 2. Perspectives in terms of the impacts on climate dynamics and future satellite observational systems are briefly discussed.

Impact of oceanic-scale interactions on the seasonal modulation of ocean dynamics by the atmosphere

PubMed Central

Sasaki, Hideharu; Klein, Patrice; Qiu, Bo; Sasai, Yoshikazu

2014-01-01

Ocean eddies (with a size of 100–300 km), ubiquitous in satellite observations, are known to represent about 80% of the total ocean kinetic energy. Recent studies have pointed out the unexpected role of smaller oceanic structures (with 1–50 km scales) in generating and sustaining these eddies. The interpretation proposed so far invokes the internal instability resulting from the large-scale interaction between upper and interior oceanic layers. Here we show, using a new high-resolution simulation of the realistic North Pacific Ocean, that ocean eddies are instead sustained by a different process that involves small-scale mixed-layer instabilities set up by large-scale atmospheric forcing in winter. This leads to a seasonal evolution of the eddy kinetic energy in a very large part of this ocean, with an amplitude varying by a factor almost equal to 2. Perspectives in terms of the impacts on climate dynamics and future satellite observational systems are briefly discussed. PMID:25501039

Approximately 800-nm-Thick Pinhole-Free Perovskite Films via Facile Solvent Retarding Process for Efficient Planar Solar Cells.

PubMed

Yuan, Zhongcheng; Yang, Yingguo; Wu, Zhongwei; Bai, Sai; Xu, Weidong; Song, Tao; Gao, Xingyu; Gao, Feng; Sun, Baoquan

2016-12-21

Device performance of organometal halide perovskite solar cells significantly depends on the quality and thickness of perovskite absorber films. However, conventional deposition methods often generate pinholes within ∼300 nm-thick perovskite films, which are detrimental to the large area device manufacture. Here we demonstrated a simple solvent retarding process to deposit uniform pinhole free perovskite films with thicknesses up to ∼800 nm. Solvent evaporation during the retarding process facilitated the components separation in the mixed halide perovskite precursors, and hence the final films exhibited pinhole free morphology and large grain sizes. In addition, the increased precursor concentration after solvent-retarding process led to thick perovskite films. Based on the uniform and thick perovskite films prepared by this convenient process, a champion device efficiency up to 16.8% was achieved. We believe that this simple deposition procedure for high quality perovskite films around micrometer thickness has a great potential in the application of large area perovskite solar cells and other optoelectronic devices.

Fine and Coarse-Scale Patterns of Vegetation Diversity on Reclaimed Surface Mine-land Over a 40-Year Chronosequence.

PubMed

Bohrer, Stefanie L; Limb, Ryan F; Daigh, Aaron L; Volk, Jay M; Wick, Abbey F

2017-03-01

Rangelands are described as heterogeneous, due to patterning in species assemblages and productivity that arise from species dispersal and interactions with environmental gradients and disturbances across multiple scales. The objectives of rangeland reclamation are typically vegetation establishment, plant community productivity, and soil stability. However, while fine-scale diversity is often promoted through species-rich seed mixes, landscape heterogeneity and coarse-scale diversity are largely overlooked. Our objectives were to evaluate fine and coarse-scale vegetation patterns across a 40-year reclamation chronosequence on reclaimed surface coalmine lands. We hypothesized that both α-diversity and β-diversity would increase and community patch size and species dissimilarity to reference sites would decrease on independent sites over 40 years. Plant communities were surveyed on 19 post-coalmine reclaimed sites and four intact native reference sites in central North Dakota mixed-grass prairie. Our results showed no differences in α or β-diversity and plant community patch size over the 40-year chronosequence. However, both α-diversity and β-diversity on reclaimed sites was similar to reference sites. Native species establishment was limited due to the presence of non-native species such as Kentucky bluegrass (Poa pratensis) on both the reclaimed and reference sites. Species composition was different between reclaimed and reference sites and community dissimilarity increased on reclaimed sites over the 40-year chronosequence. Plant communities resulting from reclamation followed non-equilibrium succession, even with consistent seeds mixes established across all reclaimed years. This suggests post-reclamation management strategies influence species composition outcomes and land management strategies applied uniformly may not increase landscape-level diversity.

Variation in pollen limitation and floral parasitism across a mating system transition in a Pacific coastal dune plant: evolutionary causes or ecological consequences?

PubMed

Dart, Sara; Eckert, Christopher G

2015-02-01

Evolutionary transitions from outcrossing to self-fertilization are thought to occur because selfing provides reproductive assurance when pollinators or mates are scarce, but they could also occur via selection to reduce floral vulnerability to herbivores. This study investigated geographic covariation between floral morphology, fruit set, pollen limitation and florivory across the geographic range of Camissoniopsis cheiranthifolia, a Pacific coastal dune endemic that varies strikingly in flower size and mating system. Fruit set was quantified in 75 populations, and in 41 of these floral herbivory by larvae of a specialized moth (Mompha sp.) that consumes anthers in developing buds was also quantified. Experimental pollen supplementation was performed to quantify pollen limitation in three large-flowered, outcrossing and two small-flowered, selfing populations. These parameters were also compared between large- and small-flowered phenotypes within three mixed populations. Fruit set was much lower in large-flowered populations, and also much lower among large- than small-flowered plants within populations. Pollen supplementation increased per flower seed production in large-flowered but not small-flowered populations, but fruit set was not pollen limited. Hence inadequate pollination cannot account for the low fruit set of large-flowered plants. Floral herbivory was much more frequent in large-flowered populations and correlated negatively with fruit set. However, florivores did not preferentially attack large-flowered plants in three large-flowered populations or in two of three mixed populations. Selfing alleviated pollen limitation of seeds per fruit, but florivory better explains the marked variation in fruit set. Although florivory was more frequent in large-flowered populations, large-flowered individuals were not generally more vulnerable within populations. Rather than a causative selective factor, reduced florivory in small-flowered, selfing populations is probably an ecological consequence of mating system differentiation, with potentially significant effects on population demography and biotic interactions. © The Author 2014. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Classification of Arctic, midlatitude and tropical clouds in the mixed-phase temperature regime

NASA Astrophysics Data System (ADS)

Costa, Anja; Meyer, Jessica; Afchine, Armin; Luebke, Anna; Günther, Gebhard; Dorsey, James R.; Gallagher, Martin W.; Ehrlich, Andre; Wendisch, Manfred; Baumgardner, Darrel; Wex, Heike; Krämer, Martina

2017-10-01

The degree of glaciation of mixed-phase clouds constitutes one of the largest uncertainties in climate prediction. In order to better understand cloud glaciation, cloud spectrometer observations are presented in this paper, which were made in the mixed-phase temperature regime between 0 and -38 °C (273 to 235 K), where cloud particles can either be frozen or liquid. The extensive data set covers four airborne field campaigns providing a total of 139 000 1 Hz data points (38.6 h within clouds) over Arctic, midlatitude and tropical regions. We develop algorithms, combining the information on number concentration, size and asphericity of the observed cloud particles to classify four cloud types: liquid clouds, clouds in which liquid droplets and ice crystals coexist, fully glaciated clouds after the Wegener-Bergeron-Findeisen process and clouds where secondary ice formation occurred. We quantify the occurrence of these cloud groups depending on the geographical region and temperature and find that liquid clouds dominate our measurements during the Arctic spring, while clouds dominated by the Wegener-Bergeron-Findeisen process are most common in midlatitude spring. The coexistence of liquid water and ice crystals is found over the whole mixed-phase temperature range in tropical convective towers in the dry season. Secondary ice is found at midlatitudes at -5 to -10 °C (268 to 263 K) and at higher altitudes, i.e. lower temperatures in the tropics. The distribution of the cloud types with decreasing temperature is shown to be consistent with the theory of evolution of mixed-phase clouds. With this study, we aim to contribute to a large statistical database on cloud types in the mixed-phase temperature regime.

Measurements of cloud condensation nuclei spectra within maritime cumulus cloud droplets: Implications for mixing processes

NASA Technical Reports Server (NTRS)

Twohy, Cynthia H.; Hudson, James G.

1995-01-01

In a cloud formed during adiabatic expansion, the droplet size distribution will be systematically related to the critical supersaturation of the cloud condensation nuclei (CNN), but this relationship can be complicated in entraining clouds. Useful information about cloud processes, such as mixing, can be obtained from direct measurements of the CNN involved in droplet nucleation. This was accomplished by interfacing two instruments for a series of flights in maritime cumulus clouds. One instrument, the counterflow virtual impactor, collected cloud droplets, and the nonvolatile residual nuclei of the droplets was then passed to a CCN spectrometer, which measured the critical supersaturation (S(sub c)) spectrum of the droplet nuclei. The measured S(sub c) spectra of the droplet nuclei were compared with the S(sub c) spectra of ambient aerosol particles in order to identify which CCN were actually incorporated into droplets and to determine when mixing processes were active at different cloud levels. The droplet nuclei nearly always exhibited lower median S(sub c)'s than the ambient aerosol, as expected since droplets nucleate perferentially on particles with lower critical supersaturations. Critical supersaturation spectra from nuclei of droplets near cloud base were similar to those predicted for cloud regions formed adiabatically, but spectra of droplet nuclei from middle cloud levels showed some evidence that mixing had occurred. Near cloud top, the greatest variation in the spectra of the droplet nuclei was observed, and nuclei with high S(sub c)'s were sometimes present even within relatively large droplets. This suggests that the extent of mixing increases with height in cumulus clouds and that inhomogeneous mixing may be important near cloud top. These promising initial results suggest improvements to the experimental technique that will permit more quantitative results in future experiments.

Ionic force field optimization based on single-ion and ion-pair solvation properties: Going beyond standard mixing rules

NASA Astrophysics Data System (ADS)

Fyta, Maria; Netz, Roland R.

2012-03-01

Using molecular dynamics (MD) simulations in conjunction with the SPC/E water model, we optimize ionic force-field parameters for seven different halide and alkali ions, considering a total of eight ion-pairs. Our strategy is based on simultaneous optimizing single-ion and ion-pair properties, i.e., we first fix ion-water parameters based on single-ion solvation free energies, and in a second step determine the cation-anion interaction parameters (traditionally given by mixing or combination rules) based on the Kirkwood-Buff theory without modification of the ion-water interaction parameters. In doing so, we have introduced scaling factors for the cation-anion Lennard-Jones (LJ) interaction that quantify deviations from the standard mixing rules. For the rather size-symmetric salt solutions involving bromide and chloride ions, the standard mixing rules work fine. On the other hand, for the iodide and fluoride solutions, corresponding to the largest and smallest anion considered in this work, a rescaling of the mixing rules was necessary. For iodide, the experimental activities suggest more tightly bound ion pairing than given by the standard mixing rules, which is achieved in simulations by reducing the scaling factor of the cation-anion LJ energy. For fluoride, the situation is different and the simulations show too large attraction between fluoride and cations when compared with experimental data. For NaF, the situation can be rectified by increasing the cation-anion LJ energy. For KF, it proves necessary to increase the effective cation-anion Lennard-Jones diameter. The optimization strategy outlined in this work can be easily adapted to different kinds of ions.

Outcomes of Mixed-Age Groupings. Research Highlights.

ERIC Educational Resources Information Center

Stegelin, Dolores A.

1997-01-01

A review of the literature on mixed-age settings reveals benefits in the areas of social and cognitive development. Research on the psychosocial advantages of mixed-age groupings is less consistent. Factors such as group size, age range, time together, and context-specific curriculum activities may have a relationship to the level of success and…

Entropic effects, shape, and size of mixed micelles formed by copolymers with complex architectures

NASA Astrophysics Data System (ADS)

Kalogirou, Andreas; Gergidis, Leonidas N.; Moultos, Othonas; Vlahos, Costas

2015-11-01

The entropic effects in the comicellization behavior of amphiphilic A B copolymers differing in the chain size of solvophilic A parts were studied by means of molecular dynamics simulations. In particular, mixtures of miktoarm star copolymers differing in the molecular weight of solvophilic arms were investigated. We found that the critical micelle concentration values show a positive deviation from the analytical predictions of the molecular theory of comicellization for chemically identical copolymers. This can be attributed to the effective interactions between copolymers originated from the arm size asymmetry. The effective interactions induce a very small decrease in the aggregation number of preferential micelles triggering the nonrandom mixing between the solvophilic moieties in the corona. Additionally, in order to specify how the chain architecture affects the size distribution and the shape of mixed micelles we studied star-shaped, H-shaped, and homo-linked-rings-linear mixtures. In the first case the individual constituents form micelles with preferential and wide aggregation numbers and in the latter case the individual constituents form wormlike and spherical micelles.

Entropic effects, shape, and size of mixed micelles formed by copolymers with complex architectures.

PubMed

Kalogirou, Andreas; Gergidis, Leonidas N; Moultos, Othonas; Vlahos, Costas

2015-11-01

The entropic effects in the comicellization behavior of amphiphilic AB copolymers differing in the chain size of solvophilic A parts were studied by means of molecular dynamics simulations. In particular, mixtures of miktoarm star copolymers differing in the molecular weight of solvophilic arms were investigated. We found that the critical micelle concentration values show a positive deviation from the analytical predictions of the molecular theory of comicellization for chemically identical copolymers. This can be attributed to the effective interactions between copolymers originated from the arm size asymmetry. The effective interactions induce a very small decrease in the aggregation number of preferential micelles triggering the nonrandom mixing between the solvophilic moieties in the corona. Additionally, in order to specify how the chain architecture affects the size distribution and the shape of mixed micelles we studied star-shaped, H-shaped, and homo-linked-rings-linear mixtures. In the first case the individual constituents form micelles with preferential and wide aggregation numbers and in the latter case the individual constituents form wormlike and spherical micelles.

The influence of Span-20 surfactant and micro-/nano-Chromium (Cr) Powder Mixed Electrical Discharge Machining (PMEDM) on the surface characteristics of AISI D2 hardened steel

NASA Astrophysics Data System (ADS)

Hosni, N. A. J.; Lajis, M. A.

2018-04-01

The application of powder mixed dielectric to improve the efficiency of electrical discharge machining (EDM) has been extensively studied. Therefore, PMEDM have attracted the attention of many researchers since last few decades. Improvement in EDM process has resulted in the use of span-20 surfactant and Cr powder mixed in dielectric fluid, which results in increasing machiniability, better surface quality and faster machining time. However, the study of powder suspension size of surface charateristics in EDM field is still limited. This paper presents the improvement of micro-/nano- Cr powder size on the surface characteristics of the AISI D2 hardened steels in PMEDM. It has found that the reacst layer in PMEDM improved by as high as 41-53 % compared to conventional EDM. Also notably, the combination of added Cr powder and span-20 surfactant reduced the recast layer thickness significantly especially in nano-Cr size. This improvement was great potential adding nano-size Cr powder to dielectric for machining performance.

Controlled morphology and size of curcumin using ultrasound in supercritical CO2 antisolvent.

PubMed

Jia, Jingfu; Wang, Wucong; Gao, Yahui; Zhao, Yaping

2015-11-01

Controllable morphology and size of crystal materials prepared by using a supercritical antisolvent (SAS) technique is still challenge. In this study, ultrasound was introduced into the SAS process to produce the particles of curcumin, a model compound. The effects of ultrasound power on the particle morphology and size were investigated in the range of 0 and 240 W at three different pressures. The observation of jet flow indicated ultrasound could accelerate the mixing speed between the liquid solution and the CO2, and thus reduced the gaseous region and the local saturation gradient. Mixed polymorphic and uniform particles of the curcumin were produced at a low and high mixing speed, respectively, confirmed by scanning electron microscopy. The needle- or rod-like particle, irregular lumpy particle and nano spherical particle were generated with the increase of the ultrasound power, attributed to the changes of the degree of supersaturation. Therefore, the ultrasound can be potentially applied to adjust the morphology and size of the crystal materials in supercritical CO2 antisolvent. Copyright © 2015 Elsevier B.V. All rights reserved.

Introducing the MCHF/OVRP/SDMP: Multicapacitated/Heterogeneous Fleet/Open Vehicle Routing Problems with Split Deliveries and Multiproducts

PubMed Central

Yilmaz Eroglu, Duygu; Caglar Gencosman, Burcu; Cavdur, Fatih; Ozmutlu, H. Cenk

2014-01-01

In this paper, we analyze a real-world OVRP problem for a production company. Considering real-world constrains, we classify our problem as multicapacitated/heterogeneous fleet/open vehicle routing problem with split deliveries and multiproduct (MCHF/OVRP/SDMP) which is a novel classification of an OVRP. We have developed a mixed integer programming (MIP) model for the problem and generated test problems in different size (10–90 customers) considering real-world parameters. Although MIP is able to find optimal solutions of small size (10 customers) problems, when the number of customers increases, the problem gets harder to solve, and thus MIP could not find optimal solutions for problems that contain more than 10 customers. Moreover, MIP fails to find any feasible solution of large-scale problems (50–90 customers) within time limits (7200 seconds). Therefore, we have developed a genetic algorithm (GA) based solution approach for large-scale problems. The experimental results show that the GA based approach reaches successful solutions with 9.66% gap in 392.8 s on average instead of 7200 s for the problems that contain 10–50 customers. For large-scale problems (50–90 customers), GA reaches feasible solutions of problems within time limits. In conclusion, for the real-world applications, GA is preferable rather than MIP to reach feasible solutions in short time periods. PMID:25045735

Synthesis of Large and Few Atomic Layers of Hexagonal Boron Nitride on Melted Copper

PubMed Central

Khan, Majharul Haque; Huang, Zhenguo; Xiao, Feng; Casillas, Gilberto; Chen, Zhixin; Molino, Paul J.; Liu, Hua Kun

2015-01-01

Hexagonal boron nitride nanosheets (h-BNNS) have been proposed as an ideal substrate for graphene-based electronic devices, but the synthesis of large and homogeneous h-BNNS is still challenging. In this contribution, we report a facile synthesis of few-layer h-BNNS on melted copper via an atmospheric pressure chemical vapor deposition process. Comparative studies confirm the advantage of using melted copper over solid copper as a catalyst substrate. The former leads to the formation of single crystalline h-BNNS that is several microns in size and mostly in mono- and bi-layer forms, in contrast to the polycrystalline and mixed multiple layers (1–10) yielded by the latter. This difference is likely to be due to the significantly reduced and uniformly distributed nucleation sites on the smooth melted surface, in contrast to the large amounts of unevenly distributed nucleation sites that are associated with grain boundaries and other defects on the solid surface. This synthesis is expected to contribute to the development of large-scale manufacturing of h-BNNS/graphene-based electronics. PMID:25582557

Synthesis of large and few atomic layers of hexagonal boron nitride on melted copper.

PubMed

Khan, Majharul Haque; Huang, Zhenguo; Xiao, Feng; Casillas, Gilberto; Chen, Zhixin; Molino, Paul J; Liu, Hua Kun

2015-01-13

Hexagonal boron nitride nanosheets (h-BNNS) have been proposed as an ideal substrate for graphene-based electronic devices, but the synthesis of large and homogeneous h-BNNS is still challenging. In this contribution, we report a facile synthesis of few-layer h-BNNS on melted copper via an atmospheric pressure chemical vapor deposition process. Comparative studies confirm the advantage of using melted copper over solid copper as a catalyst substrate. The former leads to the formation of single crystalline h-BNNS that is several microns in size and mostly in mono- and bi-layer forms, in contrast to the polycrystalline and mixed multiple layers (1-10) yielded by the latter. This difference is likely to be due to the significantly reduced and uniformly distributed nucleation sites on the smooth melted surface, in contrast to the large amounts of unevenly distributed nucleation sites that are associated with grain boundaries and other defects on the solid surface. This synthesis is expected to contribute to the development of large-scale manufacturing of h-BNNS/graphene-based electronics.

Insights of Mixing on the Assembly of DNA Nanoparticles

NASA Astrophysics Data System (ADS)

Williams, Manda S.

Size is a crucial parameter in the delivery of nanoparticle therapeutics, affecting mechanisms such as tissue delivery, clearance, and cellular uptake. The morphology of nanoparticles is dependent both upon chemistry and the physical process of assembly. Polyplexes, a major class of non-viral gene delivery vectors, are conventionally prepared by vortex mixing, resulting in non-uniform nanoparticles and poor reproducibility. Better understanding and control of the physical process of assembly, and mixing in particular, will produce polyplexes of a more uniform and reliable size, optimizing their efficiency for laboratory and clinical use. "Mixing" is the reduction of length scale of a system to accelerate diffusion until a uniform concentration is achieved. Vortex mixing is poorly characterized and sensitive to protocols. Microfluidic systems are notable for predictable fluid behavior, and are ideal for analyzing and controlling the physical interaction of reagents on the microscale, realm where mixing occurs. Several microdevices for the preparation of DNA polyplexes are explored here. Firstly, the staggered herringbone mixer, a chaotic advection micromixer, is used to observe the effects of mixing time on nanoparticle size. Next, a novel device to surround the reagent flows with a sheath of buffer, preventing interaction with the walls and confining the complexation to a zone of lower, less variable shear and residence time, is used to demonstrate the role of shear in nanoparticle assembly. Lastly, uneven diffusion between ion pairs produces a small separation of charge at fluid interfaces; this short-lived electric field has a significant impact on the transport of DNA over the time scales of mixing and complexation. The effects of common buffers on the transport of DNA are examined for possible applications to mixing and complexation. These three investigations demonstrate the importance of the physical process in polyplex assembly, and indicate several important considerations in the development of new protocols and devices.

Catalyst support of mixed cerium zirconium titanium oxide, including use and method of making

DOEpatents

Willigan, Rhonda R [Manchester, CT; Vanderspurt, Thomas Henry [Glastonbury, CT; Tulyani, Sonia [Manchester, CT; Radhakrishnan, Rakesh [Vernon, CT; Opalka, Susanne Marie [Glastonbury, CT; Emerson, Sean C [Broad Brook, CT

2011-01-18

A durable catalyst support/catalyst is capable of extended water gas shift operation under conditions of high temperature, pressure, and sulfur levels. The support is a homogeneous, nanocrystalline, mixed metal oxide of at least three metals, the first being cerium, the second being Zr, and/or Hf, and the third importantly being Ti, the three metals comprising at least 80% of the metal constituents of the mixed metal oxide and the Ti being present in a range of 5% to 45% by metals-only atomic percent of the mixed metal oxide. The mixed metal oxide has an average crystallite size less than 6 nm and forms a skeletal structure with pores whose diameters are in the range of 4-9 nm and normally greater than the average crystallite size. The surface area of the skeletal structure per volume of the material of the structure is greater than about 240 m.sup.2/cm.sup.3. The method of making and use are also described.

Supersaturation, droplet spectra, and turbulent mixing in clouds

NASA Technical Reports Server (NTRS)

Gerber, H.

1990-01-01

Much effort has recently gone into explaining the observed broad precoalescence size distribution of droplets in cloud and fogs, because this differs from the results of condensational growth calculations which lead to much narrower distributions. A good example of droplet size-distribution broadening was observed on flight 17 (25 July) of the NRL tethered balloon during the 1987 FIRE San Nicolas Island IFO. These observations caused the interactions between cloud microphysics and turbulent mixing to be re-examined. The findings of Broadwell and Breidenthal (1982) who conducted laboratory and theoretical studies of mixing in shear flow, and those of Baker et al. (1984) who applied the earlier work to mixing in clouds, were used. Rather than looking at the 25 July case at SNI, earlier fog observations made at SUNY (6 Oct. 1982) which also indicated that shear-induced mixing was taking place, and which had a better collection of microphysical measurements including more precise supersaturation measurements and detailed vertical profiles of meteorological parameters were chosen instead.

Effect of the Hartmann number on phase separation controlled by magnetic field for binary mixture system with large component ratio

NASA Astrophysics Data System (ADS)

Heping, Wang; Xiaoguang, Li; Duyang, Zang; Rui, Hu; Xingguo, Geng

2017-11-01

This paper presents an exploration for phase separation in a magnetic field using a coupled lattice Boltzmann method (LBM) with magnetohydrodynamics (MHD). The left vertical wall was kept at a constant magnetic field. Simulations were conducted by the strong magnetic field to enhance phase separation and increase the size of separated phases. The focus was on the effect of magnetic intensity by defining the Hartmann number (Ha) on the phase separation properties. The numerical investigation was carried out for different governing parameters, namely Ha and the component ratio of the mixed liquid. The effective morphological evolutions of phase separation in different magnetic fields were demonstrated. The patterns showed that the slant elliptical phases were created by increasing Ha, due to the formation and increase of magnetic torque and force. The dataset was rearranged for growth kinetics of magnetic phase separation in a plot by spherically averaged structure factor and the ratio of separated phases and total system. The results indicate that the increase in Ha can increase the average size of separated phases and accelerate the spinodal decomposition and domain growth stages. Specially for the larger component ratio of mixed phases, the separation degree was also significantly improved by increasing magnetic intensity. These numerical results provide guidance for setting the optimum condition for the phase separation induced by magnetic field.

Th-230 - U-238 series disequilibrium of the Olkaria basalts Gregory Rift Valley, Kenya: Petrogenesis

NASA Technical Reports Server (NTRS)

Black, S.; Macdonald, R.; Kelly, M.

1993-01-01

Strong mixing trends on a (Th-230/Th-232) versus Th diagram show that the basalts are mixed magmas which have undergone interaction with the crust. Instantaneous Th/U ratios are less than time integrated ones but these exceed the Th/U ratios in the MORB and OIB sources. This indicates that the mantle may have undergone some metasomatic fluxing, crustal contamination of the basalts will also enhance these ratios. Early activity on the Akira plain is represented by early basalts and hawaiites. The early basalt samples are known to predate the earliest comendites. The most recent phase of activity is represented by another cinder cone 40-50 m high being feldspar and clinopyroxene phyric. Inclusions which occur in the comendites vary in size and distribution. The largest and most porphyritic are the trachytes (up to 40 cm) with alkali feldspar phases up to 6 mm and small pyroxenes in the ground mass. The second set of inclusions are smaller (up to 10 cm) and are largely aphyric. The distribution of the inclusions are not uniform, the Broad Acres (C5) lavas contain 2-5 percent. The size of the inclusions decrease from south to north, as does the abundance of the trachytic inclusions. The major element variations in the Naivasha basalts, hawaiites and magmatic inclusions are discussed.

Will smaller plates lead to smaller waists? A systematic review and meta-analysis of the effect that experimental manipulation of dishware size has on energy consumption.

PubMed

Robinson, E; Nolan, S; Tudur-Smith, C; Boyland, E J; Harrold, J A; Hardman, C A; Halford, J C G

2014-10-01

It has been suggested that providing consumers with smaller dishware may prove an effective way of helping people eat less and preventing weight gain, but experimental evidence supporting this has been mixed. The objective of the present work was to examine the current evidence base for whether experimentally manipulated differences in dishware size influence food consumption. We systematically reviewed studies that experimentally manipulated the dishware size participants served themselves at a meal with and measured subsequent food intake. We used inverse variance meta-analysis, calculating the standardized mean difference (SMD) in food intake between smaller and larger dishware size conditions. Nine experiments from eight publications were eligible for inclusion. The majority of experiments found no significance difference in food intake when participants ate from smaller vs. larger dishware. With all available data included, analysis indicated a marginal effect of dishware size on food intake, with larger dishware size associated with greater intake. However, this effect was small and there was a large amount of heterogeneity across studies (SMD: -0.18, 95% confidence interval: -0.35, 0.00, I(2) = 77%). Evidence to date does not show that dishware size has a consistent effect on food intake, so recommendations surrounding the use of smaller plates/dishware to improve public health may be premature. © 2014 The Authors. obesity reviews © 2014 World Obesity.

Gap-based silviculture in a sierran mixed-conifer forest: effects of gap size on early survival and 7-year seedling growth

Treesearch

Robert A. York; John J. Battles; Robert C. Heald

2007-01-01

Experimental canopy gaps ranging in size from 0.1 to 1.0 ha (0.25 to 2.5 acres) were created in a mature mixed conifer forest at Blodgett Forest Research Station, California. Following gap creation, six species were planted in a wagon-wheel design and assessed for survival after two growing seasons. Study trees were measured after seven years to describe the effect of...

Sensitivity of Cirrus and Mixed-phase Clouds to the Ice Nuclei Spectra in McRAS-AC: Single Column Model Simulations

NASA Technical Reports Server (NTRS)

Betancourt, R. Morales; Lee, D.; Oreopoulos, L.; Sud, Y. C.; Barahona, D.; Nenes, A.

2012-01-01

The salient features of mixed-phase and ice clouds in a GCM cloud scheme are examined using the ice formation parameterizations of Liu and Penner (LP) and Barahona and Nenes (BN). The performance of LP and BN ice nucleation parameterizations were assessed in the GEOS-5 AGCM using the McRAS-AC cloud microphysics framework in single column mode. Four dimensional assimilated data from the intensive observation period of ARM TWP-ICE campaign was used to drive the fluxes and lateral forcing. Simulation experiments where established to test the impact of each parameterization in the resulting cloud fields. Three commonly used IN spectra were utilized in the BN parameterization to described the availability of IN for heterogeneous ice nucleation. The results show large similarities in the cirrus cloud regime between all the schemes tested, in which ice crystal concentrations were within a factor of 10 regardless of the parameterization used. In mixed-phase clouds there are some persistent differences in cloud particle number concentration and size, as well as in cloud fraction, ice water mixing ratio, and ice water path. Contact freezing in the simulated mixed-phase clouds contributed to transfer liquid to ice efficiently, so that on average, the clouds were fully glaciated at T approximately 260K, irrespective of the ice nucleation parameterization used. Comparison of simulated ice water path to available satellite derived observations were also performed, finding that all the schemes tested with the BN parameterization predicted 20 average values of IWP within plus or minus 15% of the observations.

Influence of barley grain particle size and treatment with citric acid on digestibility, ruminal fermentation and microbial protein synthesis in Holstein calves.

PubMed

Kazemi-Bonchenari, M; Salem, A Z M; López, S

2017-08-01

Chemical and physical treatments of barley grain increase ruminally resistant starch and can improve the rumen fermentation pattern. The objective of the present study was to evaluate the effects of chemical (addition of citric acid, CA) and physical (grinding to two different particle sizes, PS) treatment of barley grain on performance, rumen fermentation, microbial protein yield in the rumen and selected blood metabolites in growing calves. In all, 28 male Holstein calves (172±5.1 kg initial BW) were used in a complete randomised design with a factorial arrangement of 2 barley grain particle sizes×2 levels of citric acid. The diets were as follows: (i) small PS (average 1200 µm) barley grain soaked in water (no CA addition); (ii) small PS barley grain soaked in a CA solution (adding 20 g CA/kg barley); (iii) large PS (average 2400 µm) barley grain soaked in water (no citric acid addition) and (iv) large PS barley grain soaked in a citric acid solution (adding 20 g CA/kg barley). Barley grain was then incorporated at 35% in a total mixed ration and fed to the calves for 11 weeks. Feeding small PS barley decreased feed intake (P=0.02) and average daily weight gain (P=0.01). The addition of CA to barley grain did not affect intake but increased weight gain (P0.05). However, the molar proportion of propionate was increased (P=0.03) when barley was more finely ground, and that of acetate was increased (P=0.04) when CA was added to barley grain. The ruminal concentration of ammonia nitrogen was increased (P<0.01) and microbial nitrogen synthesis in the rumen tended to decrease by adding CA to barley. Treating barley grain with citric acid increased fibre digestibility of total mixed rations, attenuated the decrease in ruminal pH, and improved weight gain and feed efficiency in male Holstein growing calves fed a high-cereal diet (550 g cereal grain/kg diet).

Clear microstructure-performance relationships in Mn-containing perovskite and hexaaluminate compounds prepared by activated reactive synthesis.

PubMed

Laassiri, Said; Bion, Nicolas; Duprez, Daniel; Royer, Sébastien; Alamdari, Houshang

2014-03-07

Microstructural properties of mixed oxides play essential roles in their oxygen mobility and consequently in their catalytic performances. Two families of mixed oxides (perovskite and hexaaluminate) with different microstructural features, such as crystal size and specific surface area, were prepared using the activated reactive synthesis (ARS) method. It was shown that ARS is a flexible route to synthesize both mixed oxides with nano-scale crystal size and high specific surface area. Redox properties and oxygen mobility were found to be strongly affected by the material microstructure. Catalytic activities of hexaaluminate and perovskite materials for methane oxidation were discussed in the light of structural, redox and oxygen mobility properties.

Nonprofit ownership and quality in Medicaid's longterm care program for persons with developmental disabilities.

PubMed

Brown, Samuel L

2002-01-01

To assess ownership-related differences in the Intermediate Care Facility Program for persons with Mental Retardation (ICF/MR) Industry, this article analyzes a nationally representative sample of data on Medicaid certified facilities from the Health Care Financing Administration On-line Survey and Certification Reporting System. This study found that nonprofit providers provided a higher level of quality than for-profit facilities when organizational size and facility-mix were controlled. The size and case-mix composition of these facilities were also influenced by nonprofit ownership type. Nonprofit providers offered smaller facilities, on average, and were more likely to enroll heavy case-mix residents than their for-profit counterparts.

Analysis of particle size to erosion wear of sliding sleeve ball seat based on fluent software

NASA Astrophysics Data System (ADS)

Ding, Kun; Yin, Hongcheng; Wan, Bingqian; Cheng, Hao; Xiang, Lu; Li, Jianmin

2017-04-01

The fracturing has become the most offensive stimulation treatment in the low permeability reservoir. But, as the construction displacement and sand dosage of overlong horizontal well were increased continuously, the erosion wear of ball seat of pitching sliding sleeve was increasingly serious, which might lead to the failure of opening the sliding sleeve. In the existing literature, there were many researches on the erosion wear of liquid-solid two-phase flow in the diameter of sudden expansion pipe, but the influence of solid particle with mixed particle size to the erosion wear was not considered. This paper studied the erosion wear of ball seat according to the mixed proppant with different particle sizes, and carried out the numerical simulation with Fluent software with the Euler two-fluid theory. The results showed that: the erosion wear rate of ball seat is in inversely proportional to the particle size of proppant; the erosion wear rate of ball seat is different when the volume fraction of proppant with different particle sizes is changed; and for the mixed proppant of which the particle size is 0.3mm and 0.8mm, the erosion wear rate of ball seat is minimum when the volume fraction of proppant, of which the particle size is 0.3mm, is about 20%. The simulated result contributed to the deep study on erosion wear law of solid particle, and meanwhile, provided a certain reference basis for the selection of staged fracturing material of horizontal well.