Nutrient pollution of coastal rivers, bays, and seas

USGS Publications Warehouse

Howarth, Robert; Anderson, Donald; Cloern, James; Elfring, Chris; Hopkinson, Charles; Lapointe, Brian; Malone, Tom; Marcus, Nancy; McGlathery, Karen; Sharpley , Andrew; Walker, Dan

2000-01-01

Over the past 40 years, antipollution laws have greatly reduced discharges of toxic substances into our coastal waters. This effort, however, has focused largely on point-source pollution of industrial and municipal effluent. No comparable effort has been made to restrict the input of nitrogen (N) from municipal effluent, nor to control the flows of N and phosphorus (P) that enter waterways from dispersed or nonpoint sources such as agricultural and urban runoff or as airborne pollutants. As a result, inputs of nonpoint pollutants, particularly N, have increased dramatically. Nonpoint pollution from N and P now represents the largest pollution problem facing the vital coastal waters of the United States.

The importance of source configuration in quantifying footprints of regional atmospheric sulphur deposition.

PubMed

Vieno, M; Dore, A J; Bealey, W J; Stevenson, D S; Sutton, M A

2010-01-15

An atmospheric transport-chemistry model is applied to investigate the effects of source configuration in simulating regional sulphur deposition footprints from elevated point sources. Dry and wet depositions of sulphur are calculated for each of the 69 largest point sources in the UK. Deposition contributions for each point source are calculated for 2003, as well as for a 2010 emissions scenario. The 2010 emissions scenario has been chosen to simulate the Gothenburg protocol emission scenario. Point source location is found to be a major driver of the dry/wet deposition ratio for each deposition footprint, with increased precipitation scavenging of SO(x) in hill areas resulting in a larger fraction of the emitted sulphur being deposited within the UK for sources located near these areas. This reduces exported transboundary pollution, but, associated with the occurrence of sensitive soils in hill areas, increases the domestic threat of soil acidification. The simulation of plume rise using individual stack parameters for each point source demonstrates a high sensitivity of SO(2) surface concentration to effective source height. This emphasises the importance of using site-specific information for each major stack, which is rarely included in regional atmospheric pollution models, due to the difficulty in obtaining the required input data. The simulations quantify how the fraction of emitted SO(x) exported from the UK increases with source magnitude, effective source height and easterly location. The modelled reduction in SO(x) emissions, between 2003 and 2010 resulted in a smaller fraction being exported, with the result that the reductions in SO(x) deposition to the UK are less than proportionate to the emission reduction. This non-linearity is associated with a relatively larger fraction of the SO(2) being converted to sulphate aerosol for the 2010 scenario, in the presence of ammonia. The effect results in less-than-proportional UK benefits of reducing in SO(2) emissions, together with greater-than-proportional benefits in reducing export of UK SO(2) emissions. Copyright 2009 Elsevier B.V. All rights reserved.

Integrating sentinel watershed-systems into the monitoring and assessment of Minnesota's (USA) waters quality.

PubMed

Magner, J A; Brooks, K N

2008-03-01

Section 303(d) of the Clean Water Act requires States and Tribes to list waters not meeting water quality standards. A total maximum daily load must be prepared for waters identified as impaired with respect to water quality standards. Historically, the management of pollution in Minnesota has been focused on point-source regulation. Regulatory effort in Minnesota has improved water quality over the last three decades. Non-point source pollution has become the largest driver of conventional 303(d) listings in the 21st century. Conventional pollutants, i.e., organic, sediment and nutrient imbalances can be identified with poor land use management practices. However, the cause and effect relationship can be elusive because of natural watershed-system influences that vary with scale. Elucidation is complex because the current water quality standards in Minnesota were designed to work best with water quality permits to control point sources of pollution. This paper presents a sentinel watershed-systems approach (SWSA) to the monitoring and assessment of Minnesota waterbodies. SWSA integrates physical, chemical, and biological data over space and time using advanced technologies at selected small watersheds across Minnesota to potentially improve understanding of natural and anthropogenic watershed processes and the management of point and non-point sources of pollution. Long-term, state-of-the-art monitoring and assessment is needed to advance and improve water quality standards. Advanced water quality or ecologically-based standards that integrate physical, chemical, and biological numeric criteria offer the potential to better understand, manage, protect, and restore Minnesota's waterbodies.

Lessons Learned from OMI Observations of Point Source SO2 Pollution

NASA Technical Reports Server (NTRS)

Krotkov, N.; Fioletov, V.; McLinden, Chris

2011-01-01

The Ozone Monitoring Instrument (OMI) on NASA Aura satellite makes global daily measurements of the total column of sulfur dioxide (SO2), a short-lived trace gas produced by fossil fuel combustion, smelting, and volcanoes. Although anthropogenic SO2 signals may not be detectable in a single OMI pixel, it is possible to see the source and determine its exact location by averaging a large number of individual measurements. We describe new techniques for spatial and temporal averaging that have been applied to the OMI SO2 data to determine the spatial distributions or "fingerprints" of SO2 burdens from top 100 pollution sources in North America. The technique requires averaging of several years of OMI daily measurements to observe SO2 pollution from typical anthropogenic sources. We found that the largest point sources of SO2 in the U.S. produce elevated SO2 values over a relatively small area - within 20-30 km radius. Therefore, one needs higher than OMI spatial resolution to monitor typical SO2 sources. TROPOMI instrument on the ESA Sentinel 5 precursor mission will have improved ground resolution (approximately 7 km at nadir), but is limited to once a day measurement. A pointable geostationary UVB spectrometer with variable spatial resolution and flexible sampling frequency could potentially achieve the goal of daily monitoring of SO2 point sources and resolve downwind plumes. This concept of taking the measurements at high frequency to enhance weak signals needs to be demonstrated with a GEOCAPE precursor mission before 2020, which will help formulating GEOCAPE measurement requirements.

Neutrino Astronomy at the South Pole: latest Results from AMANDA-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desiati, Paolo

2006-07-11

AMANDA-II is the largest neutrino telescope collecting data at the moment, and its main goal is to search for sources of high energy extra-terrestrial neutrinos. The detection of such sources could give non-controversial evidence for the acceleration of charged hadrons in cosmic objects like Supernova Remnants, Micro-quasars, Active Galactic Nuclei or Gamma Ray Bursts. No significant excess has been found in searching for neutrinos from both point-like and non-localized sources. However AMANDA-II has significantly improved analysis techniques for better signal-to-noise optimization. The km3-scale IceCube telescope will enlarge the observable energy range and improve the sensitivities of high energy neutrino searchesmore » due to its 30 times larger effective area.« less

Spatial distribution of pollutants in the area of the former CHP plant

NASA Astrophysics Data System (ADS)

Cichowicz, Robert

2018-01-01

The quality of atmospheric air and level of its pollution are now one of the most important issues connected with life on Earth. The frequent nuisance and exceedance of pollution standards often described in the media are generated by both low emission sources and mobile sources. Also local organized energy emission sources such as local boiler houses or CHP plants have impact on air pollution. At the same time it is important to remember that the role of local power stations in shaping air pollution immission fields depends on the height of emitters and functioning of waste gas treatment installations. Analysis of air pollution distribution was carried out in 2 series/dates, i.e. 2 and 10 weeks after closure of the CHP plant. In the analysis as a reference point the largest intersection of streets located in the immediate vicinity of the plant was selected, from which virtual circles were drawn every 50 meters, where 31 measuring points were located. As a result, the impact of carbon dioxide, hydrogen sulfide and ammonia levels could be observed and analyzed, depending on the distance from the street intersection.

Large emissions from floodplain trees close the Amazon methane budget.

PubMed

Pangala, Sunitha R; Enrich-Prast, Alex; Basso, Luana S; Peixoto, Roberta Bittencourt; Bastviken, David; Hornibrook, Edward R C; Gatti, Luciana V; Marotta, Humberto; Calazans, Luana Silva Braucks; Sakuragui, Cassia Mônica; Bastos, Wanderley Rodrigues; Malm, Olaf; Gloor, Emanuel; Miller, John Bharat; Gauci, Vincent

2017-12-14

Wetlands are the largest global source of atmospheric methane (CH 4 ), a potent greenhouse gas. However, methane emission inventories from the Amazon floodplain, the largest natural geographic source of CH 4 in the tropics, consistently underestimate the atmospheric burden of CH 4 determined via remote sensing and inversion modelling, pointing to a major gap in our understanding of the contribution of these ecosystems to CH 4 emissions. Here we report CH 4 fluxes from the stems of 2,357 individual Amazonian floodplain trees from 13 locations across the central Amazon basin. We find that escape of soil gas through wetland trees is the dominant source of regional CH 4 emissions. Methane fluxes from Amazon tree stems were up to 200 times larger than emissions reported for temperate wet forests and tropical peat swamp forests, representing the largest non-ebullitive wetland fluxes observed. Emissions from trees had an average stable carbon isotope value (δ 13 C) of -66.2 ± 6.4 per mil, consistent with a soil biogenic origin. We estimate that floodplain trees emit 15.1 ± 1.8 to 21.2 ± 2.5 teragrams of CH 4 a year, in addition to the 20.5 ± 5.3 teragrams a year emitted regionally from other sources. Furthermore, we provide a 'top-down' regional estimate of CH 4 emissions of 42.7 ± 5.6 teragrams of CH 4 a year for the Amazon basin, based on regular vertical lower-troposphere CH 4 profiles covering the period 2010-2013. We find close agreement between our 'top-down' and combined 'bottom-up' estimates, indicating that large CH 4 emissions from trees adapted to permanent or seasonal inundation can account for the emission source that is required to close the Amazon CH 4 budget. Our findings demonstrate the importance of tree stem surfaces in mediating approximately half of all wetland CH 4 emissions in the Amazon floodplain, a region that represents up to one-third of the global wetland CH 4 source when trees are combined with other emission sources.

Large emissions from floodplain trees close the Amazon methane budget

NASA Astrophysics Data System (ADS)

Pangala, Sunitha R.; Enrich-Prast, Alex; Basso, Luana S.; Peixoto, Roberta Bittencourt; Bastviken, David; Hornibrook, Edward R. C.; Gatti, Luciana V.; Marotta, Humberto; Calazans, Luana Silva Braucks; Sakuragui, Cassia Mônica; Bastos, Wanderley Rodrigues; Malm, Olaf; Gloor, Emanuel; Miller, John Bharat; Gauci, Vincent

2017-12-01

Wetlands are the largest global source of atmospheric methane (CH4), a potent greenhouse gas. However, methane emission inventories from the Amazon floodplain, the largest natural geographic source of CH4 in the tropics, consistently underestimate the atmospheric burden of CH4 determined via remote sensing and inversion modelling, pointing to a major gap in our understanding of the contribution of these ecosystems to CH4 emissions. Here we report CH4 fluxes from the stems of 2,357 individual Amazonian floodplain trees from 13 locations across the central Amazon basin. We find that escape of soil gas through wetland trees is the dominant source of regional CH4 emissions. Methane fluxes from Amazon tree stems were up to 200 times larger than emissions reported for temperate wet forests and tropical peat swamp forests, representing the largest non-ebullitive wetland fluxes observed. Emissions from trees had an average stable carbon isotope value (δ13C) of -66.2 ± 6.4 per mil, consistent with a soil biogenic origin. We estimate that floodplain trees emit 15.1 ± 1.8 to 21.2 ± 2.5 teragrams of CH4 a year, in addition to the 20.5 ± 5.3 teragrams a year emitted regionally from other sources. Furthermore, we provide a ‘top-down’ regional estimate of CH4 emissions of 42.7 ± 5.6 teragrams of CH4 a year for the Amazon basin, based on regular vertical lower-troposphere CH4 profiles covering the period 2010-2013. We find close agreement between our ‘top-down’ and combined ‘bottom-up’ estimates, indicating that large CH4 emissions from trees adapted to permanent or seasonal inundation can account for the emission source that is required to close the Amazon CH4 budget. Our findings demonstrate the importance of tree stem surfaces in mediating approximately half of all wetland CH4 emissions in the Amazon floodplain, a region that represents up to one-third of the global wetland CH4 source when trees are combined with other emission sources.

Assessing sources of airborne mineral dust and other aerosols, in Iraq

NASA Astrophysics Data System (ADS)

Engelbrecht, Johann P.; Jayanty, R. K. M.

2013-06-01

Most airborne particulate matter in Iraq comes from mineral dust sources. This paper describes the statistics and modeling of chemical results, specifically those from Teflon® filter samples collected at Tikrit, Balad, Taji, Baghdad, Tallil and Al Asad, in Iraq, in 2006/2007. Methodologies applied to the analytical results include calculation of correlation coefficients, Principal Components Analysis (PCA), and Positive Matrix Factorization (PMF) modeling. PCA provided a measure of the covariance within the data set, thereby identifying likely point sources and events. These include airborne mineral dusts of silicate and carbonate minerals, gypsum and salts, as well as anthropogenic sources of metallic fumes, possibly from battery smelting operations, and emissions of leaded gasoline vehicles. Five individual PMF factors (source categories) were modeled, four of which being assigned to components of geological dust, and the fifth to gasoline vehicle emissions together with battery smelting operations. The four modeled geological components, dust-siliceous, dust-calcic, dust-gypsum, and evaporate occur in variable ratios for each site and size fraction (TSP, PM10, and PM2.5), and also vary by season. In general, Tikrit and Taji have the largest and Al Asad the smallest percentages of siliceous dust. In contrast, Al Asad has the largest proportion of gypsum, in part representing the gypsiferous soils in that region. Baghdad has the highest proportions of evaporite in both size fractions, ascribed to the highly salinized agricultural soils, following millennia of irrigation along the Tigris River valley. Although dust storms along the Tigris and Euphrates River valleys originate from distal sources, the mineralogy bears signatures of local soils and air pollutants.

Export of microplastics from land to sea. A modelling approach.

PubMed

Siegfried, Max; Koelmans, Albert A; Besseling, Ellen; Kroeze, Carolien

2017-12-15

Quantifying the transport of plastic debris from river to sea is crucial for assessing the risks of plastic debris to human health and the environment. We present a global modelling approach to analyse the composition and quantity of point-source microplastic fluxes from European rivers to the sea. The model accounts for different types and sources of microplastics entering river systems via point sources. We combine information on these sources with information on sewage management and plastic retention during river transport for the largest European rivers. Sources of microplastics include personal care products, laundry, household dust and tyre and road wear particles (TRWP). Most of the modelled microplastics exported by rivers to seas are synthetic polymers from TRWP (42%) and plastic-based textiles abraded during laundry (29%). Smaller sources are synthetic polymers and plastic fibres in household dust (19%) and microbeads in personal care products (10%). Microplastic export differs largely among European rivers, as a result of differences in socio-economic development and technological status of sewage treatment facilities. About two-thirds of the microplastics modelled in this study flow into the Mediterranean and Black Sea. This can be explained by the relatively low microplastic removal efficiency of sewage treatment plants in the river basins draining into these two seas. Sewage treatment is generally more efficient in river basins draining into the North Sea, the Baltic Sea and the Atlantic Ocean. We use our model to explore future trends up to the year 2050. Our scenarios indicate that in the future river export of microplastics may increase in some river basins, but decrease in others. Remarkably, for many basins we calculate a reduction in river export of microplastics from point-sources, mainly due to an anticipated improvement in sewage treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

An X-ray Investigation of the NGC 346 Field in the SMC (2): The Field Population

NASA Technical Reports Server (NTRS)

Naze, Y.; Hartwell, J. M.; Stevens, I. R.; Manfroid, J.; Marchenko. S.; Corcoran, M. F.; Moffat, A. F. J.; Skalkowski, G.; White, Nicholas E. (Technical Monitor)

2002-01-01

We present results from a Chandra observation of the NGC 346 cluster, the ionizing source of N66, the most luminous H II region and the largest star formation region in the SMC. In the first part of this investigation, we have analysed the X-ray properties of the cluster itself and the remarkable star HD 5980. But the field contains additional objects of interest. In total, 79 X-ray point sources were detected in the Chandra observation and we investigate here their characteristics in details. The sources possess rather high HRs, and their cumulative luminosity function is steeper than the SMC's trend. Their absorption columns suggest that most of the sources belong to NGC 346. Using new UBVRI imaging with the ESO 2.2m telescope, we also discovered possible counterparts for 36 of these X-ray sources. Finally, some objects show X-ray and/or optical variability, and thus need further monitoring.

Methane Yield Database: Online infrastructure and bioresource for methane yield data and related metadata.

PubMed

Murovec, Boštjan; Kolbl, Sabina; Stres, Blaž

2015-01-01

The aim of this study was to develop and validate a community supported online infrastructure and bioresource for methane yield data and accompanying metadata collected from published literature. In total, 1164 entries described by 15,749 data points were assembled. Analysis of data collection showed little congruence in reporting of methodological approaches. The largest identifiable source of variation in reported methane yields was represented by authorship (i.e. substrate batches within particular substrate class) within which experimental scales (volumes (0.02-5l), incubation temperature (34-40 °C) and % VS of substrate played an important role (p < 0.05, npermutations = 999) as well. The largest fraction of variability, however, remained unaccounted for and thus unexplained (> 63%). This calls for reconsideration of accepted approaches to reporting data in currently published literature to increase capacity to service industrial decision making to a greater extent. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oil palm biomass utilization as an energy source and its possibility use for polygeneration scenarios in Langsa City, Aceh Province, Indonesia

NASA Astrophysics Data System (ADS)

Hani, M. R.; Mahidin, M.; Husin, H.; Hamdani, H.; Khairil, K.

2018-03-01

This article deals with the discussion on the recent status of oil palm biomass utilization as an energy source and its possibility use for polygeneration system. The discussion focused only on the energy viewpoint. At this point, many projects and research have been developed in order to utilize the oil palm biomass to meet the energy demand of industries and communities, especially in the largest producing countries: Indonesia and Malaysia; and a few in Thailand, Africa, Latin America and Europe. Through the simulation work in the case study, it is evident that the government of Langsa City can fulfill the fresh water to their community and electricity to Langsa Harbor only by using EFB and PKS from one POM with the generated power of 12 MW, while the desalination plant consumes about 7 MW of electricity. If all potency of biomass from all POMs in Aceh Timur and Aceh Tamiang, without the combination of other primary energy sources is used, Langsa City might earn surplus of energy. The use of the oil palm biomass for polygeneration scenarios is possible and feasible from the technical point of view.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nitao, J J

The goal of the Event Reconstruction Project is to find the location and strength of atmospheric release points, both stationary and moving. Source inversion relies on observational data as input. The methodology is sufficiently general to allow various forms of data. In this report, the authors will focus primarily on concentration measurements obtained at point monitoring locations at various times. The algorithms being investigated in the Project are the MCMC (Markov Chain Monte Carlo), SMC (Sequential Monte Carlo) Methods, classical inversion methods, and hybrids of these. They refer the reader to the report by Johannesson et al. (2004) for explanationsmore » of these methods. These methods require computing the concentrations at all monitoring locations for a given ''proposed'' source characteristic (locations and strength history). It is anticipated that the largest portion of the CPU time will take place performing this computation. MCMC and SMC will require this computation to be done at least tens of thousands of times. Therefore, an efficient means of computing forward model predictions is important to making the inversion practical. In this report they show how Green's functions and reciprocal Green's functions can significantly accelerate forward model computations. First, instead of computing a plume for each possible source strength history, they can compute plumes from unit impulse sources only. By using linear superposition, they can obtain the response for any strength history. This response is given by the forward Green's function. Second, they may use the law of reciprocity. Suppose that they require the concentration at a single monitoring point x{sub m} due to a potential (unit impulse) source that is located at x{sub s}. instead of computing a plume with source location x{sub s}, they compute a ''reciprocal plume'' whose (unit impulse) source is at the monitoring locations x{sub m}. The reciprocal plume is computed using a reversed-direction wind field. The wind field and transport coefficients must also be appropriately time-reversed. Reciprocity says that the concentration of reciprocal plume at x{sub s} is related to the desired concentration at x{sub m}. Since there are many less monitoring points than potential source locations, the number of forward model computations is drastically reduced.« less

New approach for point pollution source identification in rivers based on the backward probability method.

PubMed

Wang, Jiabiao; Zhao, Jianshi; Lei, Xiaohui; Wang, Hao

2018-06-13

Pollution risk from the discharge of industrial waste or accidental spills during transportation poses a considerable threat to the security of rivers. The ability to quickly identify the pollution source is extremely important to enable emergency disposal of pollutants. This study proposes a new approach for point source identification of sudden water pollution in rivers, which aims to determine where (source location), when (release time) and how much pollutant (released mass) was introduced into the river. Based on the backward probability method (BPM) and the linear regression model (LR), the proposed LR-BPM converts the ill-posed problem of source identification into an optimization model, which is solved using a Differential Evolution Algorithm (DEA). The decoupled parameters of released mass are not dependent on prior information, which improves the identification efficiency. A hypothetical case study with a different number of pollution sources was conducted to test the proposed approach, and the largest relative errors for identified location, release time, and released mass in all tests were not greater than 10%. Uncertainty in the LR-BPM is mainly due to a problem with model equifinality, but averaging the results of repeated tests greatly reduces errors. Furthermore, increasing the gauging sections further improves identification results. A real-world case study examines the applicability of the LR-BPM in practice, where it is demonstrated to be more accurate and time-saving than two existing approaches, Bayesian-MCMC and basic DEA. Copyright © 2018 Elsevier Ltd. All rights reserved.

Analysis of point source pollution and water environmental quality variation trends in the Nansi Lake basin from 2002 to 2012.

PubMed

Wang, Weiliang; Liu, Xiaohui; Wang, Yufan; Guo, Xiaochun; Lu, Shaoyong

2016-03-01

Based on the data analysis of the water environmental quality and economic development from 2002 to 2012 in the Nansi Lake basin, the correlation and change between the water environmental quality and economic development were studied. Results showed that the GDP and wastewater emissions of point source in the Nansi Lake basin had an average annual growth of 7.30 and 7.68 %, respectively, from 2002 to 2012. The emissions of chemical oxygen demand (COD) and ammonia nitrogen (NH3-N) had the average annual decrease of 7.69 and 6.79 % in 2012, respectively, compared to 2002. Basin water quality overall improved, reaching the Class III of the "Environmental quality standards for surface water (GB3838-2002)," in which the main reason was that sewage treatment rate increased gradually and was above 90 % in 2012 (an increase of 10 % compared to 2002) with the progress of pollution abatement technology and the implementation of relevant policies and regulations. The contribution of water environmental pollution was analyzed from related cities (Ji'ning, Zaozhuang, Heze). Results indicated that Ji'ning had the largest contribution to water pollution of the Nansi Lake basin, and the pollutant from domestic sources accounted for a higher percentage compared to industrial sources. The wastewater, COD, and NH3-N mainly came from mining and washing of coal, manufacture of raw chemical materials and chemical products, papermaking industry, and food processing industry. According to the water pollution characteristics of the Nansi Lake basin, the basin pollution treatment strategy and prevention and treatment system were dissected to provide a scientific basis for prevention and control of lakeside point source pollution along the Nansi Lake.

Work status and disability trajectories over 12 months after injury among workers in New Zealand.

PubMed

Langley, John; Lilley, Rebbecca; Samaranayaka, Ari; Derrett, Sarah

2014-03-07

To describe work and disability trajectories over 12 months following injury among workers. Workers injured at work or elsewhere (n=2626) were sourced from the Prospective Outcomes of Injury Study, a longitudinal cohort study in New Zealand, with the primary objective of identifying factors associated with disability following injury. Work and disability status was assessed at 3- and 12-months post injury. The measure of disability was the brief WHODAS II 12-item instrument. Participants were dichotomised into 'disability' or 'no disability' groups based on whether their WHODAS score was greater than, or equal to, 10. In terms of 12-month work status, there are 16 different scenarios. These were grouped into 4 categories: sustained work (SW), delayed return to work (RTW), non-sustained RTW, and sustained off-work. We had complete information for 1975 workers. The largest group (68%) was SW, 32% of which had disability at either time point. The second largest group consisted of 17% of workers who were classified as delayed RTW, 76% of whom were disabled at either time point. Among the non-sustained RTW group (7%), 52% had disability at either time point. Of the sustained off-work group (8%), 80% were disabled at either 3- or 12-months. Although return to work is a useful provider performance indicator of injury compensation and rehabilitation it is inadequate from a wider societal perspective and needs to be complemented by other important outcome measures such as disability status.

Estimating photometric redshifts for X-ray sources in the X-ATLAS field using machine-learning techniques

NASA Astrophysics Data System (ADS)

Mountrichas, G.; Corral, A.; Masoura, V. A.; Georgantopoulos, I.; Ruiz, A.; Georgakakis, A.; Carrera, F. J.; Fotopoulou, S.

2017-12-01

We present photometric redshifts for 1031 X-ray sources in the X-ATLAS field using the machine-learning technique TPZ. X-ATLAS covers 7.1 deg2 observed with XMM-Newton within the Science Demonstration Phase of the H-ATLAS field, making it one of the largest contiguous areas of the sky with both XMM-Newton and Herschel coverage. All of the sources have available SDSS photometry, while 810 additionally have mid-IR and/or near-IR photometry. A spectroscopic sample of 5157 sources primarily in the XMM/XXL field, but also from several X-ray surveys and the SDSS DR13 redshift catalogue, was used to train the algorithm. Our analysis reveals that the algorithm performs best when the sources are split, based on their optical morphology, into point-like and extended sources. Optical photometry alone is not enough to estimate accurate photometric redshifts, but the results greatly improve when at least mid-IR photometry is added in the training process. In particular, our measurements show that the estimated photometric redshifts for the X-ray sources of the training sample have a normalized absolute median deviation, nmad ≈ 0.06, and a percentage of outliers, η = 10-14%, depending upon whether the sources are extended or point like. Our final catalogue contains photometric redshifts for 933 out of the 1031 X-ray sources with a median redshift of 0.9. The table of the photometric redshifts is only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/608/A39

Characterizing the size distribution of particles in urban stormwater by use of fixed-point sample-collection methods

USGS Publications Warehouse

Selbig, William R.; Bannerman, Roger T.

2011-01-01

The U.S Geological Survey, in cooperation with the Wisconsin Department of Natural Resources (WDNR) and in collaboration with the Root River Municipal Stormwater Permit Group monitored eight urban source areas representing six types of source areas in or near Madison, Wis. in an effort to improve characterization of particle-size distributions in urban stormwater by use of fixed-point sample collection methods. The types of source areas were parking lot, feeder street, collector street, arterial street, rooftop, and mixed use. This information can then be used by environmental managers and engineers when selecting the most appropriate control devices for the removal of solids from urban stormwater. Mixed-use and parking-lot study areas had the lowest median particle sizes (42 and 54 (u or mu)m, respectively), followed by the collector street study area (70 (u or mu)m). Both arterial street and institutional roof study areas had similar median particle sizes of approximately 95 (u or mu)m. Finally, the feeder street study area showed the largest median particle size of nearly 200 (u or mu)m. Median particle sizes measured as part of this study were somewhat comparable to those reported in previous studies from similar source areas. The majority of particle mass in four out of six source areas was silt and clay particles that are less than 32 (u or mu)m in size. Distributions of particles ranging from 500 (u or mu)m were highly variable both within and between source areas. Results of this study suggest substantial variability in data can inhibit the development of a single particle-size distribution that is representative of stormwater runoff generated from a single source area or land use. Continued development of improved sample collection methods, such as the depth-integrated sample arm, may reduce variability in particle-size distributions by mitigating the effect of sediment bias inherent with a fixed-point sampler.

Modeling urban air pollution in Budapest using WRF-Chem model

NASA Astrophysics Data System (ADS)

Kovács, Attila; Leelőssy, Ádám; Lagzi, István; Mészáros, Róbert

2017-04-01

Air pollution is a major problem for urban areas since the industrial revolution, including Budapest, the capital and largest city of Hungary. The main anthropogenic sources of air pollutants are industry, traffic and residential heating. In this study, we investigated the contribution of major industrial point sources to the urban air pollution in Budapest. We used the WRF (Weather Research and Forecasting) nonhydrostatic mesoscale numerical weather prediction system online coupled with chemistry (WRF-Chem, version 3.6).The model was configured with three nested domains with grid spacings of 15, 5 and 1 km, representing Central Europe, the Carpathian Basin and Budapest with its surrounding area. Emission data was obtained from the National Environmental Information System. The point source emissions were summed in their respective cells in the second nested domain according to latitude-longitude coordinates. The main examined air pollutants were carbon monoxide (CO) and nitrogen oxides (NOx), from which the secondary compound, ozone (O3) forms through chemical reactions. Simulations were performed under different weather conditions and compared to observations from the automatic monitoring site of the Hungarian Air Quality Network. Our results show that the industrial emissions have a relatively weak role in the urban background air pollution, confirming the effect of industrial developments and regulations in the recent decades. However, a few significant industrial sources and their impact area has been demonstrated.

Postglacial sedimentary record of the Southern California continental shelf and slope, Point Conception to Dana Point

USGS Publications Warehouse

Sommerfield, C.K.; Lee, H.J.; Normark, W.R.

2009-01-01

Sedimentary strata on the Southern California shelf and slope (Point Conception to Dana Point) display patterns and rates of sediment accumulation that convey information on sea-level inundation, sediment supply, and oceanic transport processes following the Last Glacial Maximum. In Santa Monica Bay and San Pedro Bay, postglacial transgression is recorded in shelf deposits by wave-ravinement surfaces dated at 13-11 ka and an upsection transition from coastal to shallow-marine sediment facies. Depositional conditions analogous to the modern environment were established in the bays by 8-9 ka. On the continental slope, transgression is evidenced in places by an increase in sediment grain size and accumulation rate ca. 15-10 ka, a consequence of coastal ravinement and downslope resedimentation, perhaps in conjunction with climatic increases in fluvial sediment delivery. Grain sizes and accumulation rates then decreased after 12-10 ka when the shelf flooded and backfilled under rising sea level. The Santa Barbara coastal cell contains the largest mass of postglacial sediment at 32-42 ?? 109 metric tons, most of which occurs between offshore Santa Barbara and Hueneme Canyon. The San Pedro cell contains the second largest quantity of sediment, 8-11 ?? 109 metric tons, much of which is present on the eastern Palos Verdes and outer San Pedro shelves. By comparison, the mass of sediment sequestered within the Santa Monica cell is smaller at ??6-8 ?? 109 metric tons. The postglacial sediment mass distribution among coastal cells reflects the size of local fluvial sediment sources, whereas intracell accumulation patterns reflect antecedent bathymetric features conducive for sediment bypass or trapping. ?? 2009 The Geological Society of America.

Oxidative potential and inflammatory impacts of source apportioned ambient air pollution in Beijing.

PubMed

Liu, Qingyang; Baumgartner, Jill; Zhang, Yuanxun; Liu, Yanju; Sun, Yongjun; Zhang, Meigen

2014-11-04

Air pollution exposure is associated with a range of adverse health impacts. Knowledge of the chemical components and sources of air pollution most responsible for these health effects could lead to an improved understanding of the mechanisms of such effects and more targeted risk reduction strategies. We measured daily ambient fine particulate matter (<2.5 μm in aerodynamic diameter; PM2.5) for 2 months in peri-urban and central Beijing, and assessed the contribution of its chemical components to the oxidative potential of ambient air pollution using the dithiothreitol (DTT) assay. The composition data were applied to a multivariate source apportionment model to determine the PM contributions of six sources or factors: a zinc factor, an aluminum factor, a lead point factor, a secondary source (e.g., SO4(2-), NO3(2-)), an iron source, and a soil dust source. Finally, we assessed the relationship between reactive oxygen species (ROS) activity-related PM sources and inflammatory responses in human bronchial epithelial cells. In peri-urban Beijing, the soil dust source accounted for the largest fraction (47%) of measured ROS variability. In central Beijing, a secondary source explained the greatest fraction (29%) of measured ROS variability. The ROS activities of PM collected in central Beijing were exponentially associated with in vivo inflammatory responses in epithelial cells (R2=0.65-0.89). We also observed a high correlation between three ROS-related PM sources (a lead point factor, a zinc factor, and a secondary source) and expression of an inflammatory marker (r=0.45-0.80). Our results suggest large differences in the contribution of different PM sources to ROS variability at the central versus peri-urban study sites in Beijing and that secondary sources may play an important role in PM2.5-related oxidative potential and inflammatory health impacts.

Long-term changes in nitrate conditions over the 20th century in two Midwestern Corn Belt streams

USGS Publications Warehouse

Kelly, Valerie J.; Stets, Edward G.; Crawford, Charles G.

2015-01-01

Long-term changes in nitrate concentration and flux between the middle of the 20th century and the first decade of the 21st century were estimated for the Des Moines River and the Middle Illinois River, two Midwestern Corn Belt streams, using a novel weighted regression approach that is able to detect subtle changes in solute transport behavior over time. The results show that the largest changes in flow-normalized concentration and flux occurred between 1960 and 1980 in both streams, with smaller or negligible changes between 1980 and 2004. Contrasting patterns were observed between (1) nitrate export linked to non-point sources, explicitly runoff of synthetic fertilizer or other surface sources and (2) nitrate export presumably associated with point sources such as urban wastewater or confined livestock feeding facilities, with each of these modes of transport important under different domains of streamflow. Surface runoff was estimated to be consistently most important under high-flow conditions during the spring in both rivers. Nitrate export may also have been considerable in the Des Moines River even under some conditions during the winter when flows are generally lower, suggesting the influence of point sources during this time. Similar results were shown for the Middle Illinois River, which is subject to significant influence of wastewater from the Chicago area, where elevated nitrate concentrations were associated with at the lowest flows during the winter and fall. By modeling concentration directly, this study highlights the complex relationship between concentration and streamflow that has evolved in these two basins over the last 50 years. This approach provides insights about changing conditions that only become observable when stationarity in the relationship between concentration and streamflow is not assumed.

Monopole, astrophysics and cosmic ray observatory at Gran Sasso

NASA Technical Reports Server (NTRS)

Demarzo, C.; Enriquez, O.; Giglietto, N.; Posa, F.; Attolini, M.; Baldetti, F.; Giacomelli, G.; Grianti, F.; Margiotta, A.; Serra, P.

1985-01-01

A new large area detector, MACRO was approved for installation at the Gran Sasso Laboratory in Italy. The detector will be dedicated to the study of naturally penetrating radiation deep underground. It is designed with the general philosophy of covering the largest possible area with a detector having both sufficient built-in redundancy and use of complementary techniques to study very rare phenomena. The detector capabilities will include monopole investigations significantly below the Parker bound; astrophysics studies of very high energy gamma ray and neutrino point sources; cosmic ray measurements of single and multimuons; and the general observation of rare new forms of matter in the cosmic rays.

Chronic toxicity of Pydraul 50E to lake trout

USGS Publications Warehouse

Mayer, Foster L.; Woodward, Daniel F.; Adams, William J.

1993-01-01

Industrial phosphate esters, both triaryl and alkyl aryl phosphate esters, are used as fire resistant hydraulic fluids and as fire retardant plasticizers (Lapp 1976). Hydraulic fluids probably represent the largest contribution of phosphate ester compounds released into the environment. Lapp (1976) estimated that 65 to 70 percent of all phosphate ester hydraulic fluids were utilized in automotive and steel industries. He also estimated that 80 percent of the annual consumption of hydraulic fluids in 1976 was the result of leaks in industrial hydraulic systems. These data suggest phosphate esters are likely to be constituents of industrial effluents and, consequently, could be in point source discharges.

Spatiotemporal patterns and source attribution of nitrogen pollution in a typical headwater agricultural watershed in Southeastern China.

PubMed

Chen, Wenjun; He, Bin; Nover, Daniel; Duan, Weili; Luo, Chuan; Zhao, Kaiyan; Chen, Wen

2018-01-01

Excessive nitrogen (N) discharge from agriculture causes widespread problems in aquatic ecosystems. Knowledge of spatiotemporal patterns and source attribution of N pollution is critical for nutrient management programs but is poorly studied in headwaters with various small water bodies and mini-point pollution sources. Taking a typical small watershed in the low mountains of Southeastern China as an example, N pollution and source attribution were studied for a multipond system around a village using the Hydrological Simulation Program-Fortran (HSPF) model. The results exhibited distinctive spatio-seasonal variations with an overall seriousness rank for the three indicators: total nitrogen (TN) > nitrate/nitrite nitrogen (NO x - -N) > ammonia nitrogen (NH 3 -N), according to the Chinese Surface Water Quality Standard. TN pollution was severe for the entire watershed, while NO x - -N pollution was significant for ponds and ditches far from the village, and the NH 3 -N concentrations were acceptable except for the ponds near the village in summer. Although food and cash crop production accounted for the largest source of N loads, we discovered that mini-point pollution sources, including animal feeding operations, rural residential sewage, and waste, together contributed as high as 47% of the TN and NH 3 -N loads in ponds and ditches. So, apart from eco-fertilizer programs and concentrated animal feeding operations, the importance of environmental awareness building for resource management is highlighted for small farmers in headwater agricultural watersheds. As a first attempt to incorporate multipond systems into the process-based modeling of nonpoint source (NPS) pollution, this work can inform other hydro-environmental studies on scattered and small water bodies. The results are also useful to water quality improvement for entire river basins.

Teleseismic Body Wave Analysis for the 27 September 2003 Altai, Earthquake (Mw7.4) and Large Aftershocks

NASA Astrophysics Data System (ADS)

Gomez-Gonzalez, J. M.; Mellors, R.

2007-05-01

We investigate the kinematics of the rupture process for the September 27, 2003, Mw7.3, Altai earthquake and its associated large aftershocks. This is the largest earthquake striking the Altai mountains within the last 50 years, which provides important constraints on the ongoing tectonics. The fault plane solution obtained by teleseismic body waveform modeling indicated a predominantly strike-slip event (strike=130, dip=75, rake 170), Scalar moment for the main shock ranges from 0.688 to 1.196E+20 N m, a source duration of about 20 to 42 s, and an average centroid depth of 10 km. Source duration would indicate a fault length of about 130 - 270 km. The main shock was followed closely by two aftershocks (Mw5.7, Mw6.4) occurred the same day, another aftershock (Mw6.7) occurred on 1 October , 2003. We also modeled the second aftershock (Mw6.4) to asses geometric similarities during their respective rupture process. This aftershock occurred spatially very close to the mainshock and possesses a similar fault plane solution (strike=128, dip=71, rake=154), and centroid depth (13 km). Several local conditions, such as the crustal model and fault geometry, affect the correct estimation of some source parameters. We perfume a sensitivity evaluation of several parameters, including centroid depth, scalar moment and source duration, based on a point and finite source modeling. The point source approximation results are the departure parameters for the finite source exploration. We evaluate the different reported parameters to discard poor constrained models. In addition, deformation data acquired by InSAR are also included in the analysis.

LEAP: Looking beyond pixels with continuous-space EstimAtion of Point sources

NASA Astrophysics Data System (ADS)

Pan, Hanjie; Simeoni, Matthieu; Hurley, Paul; Blu, Thierry; Vetterli, Martin

2017-12-01

Context. Two main classes of imaging algorithms have emerged in radio interferometry: the CLEAN algorithm and its multiple variants, and compressed-sensing inspired methods. They are both discrete in nature, and estimate source locations and intensities on a regular grid. For the traditional CLEAN-based imaging pipeline, the resolution power of the tool is limited by the width of the synthesized beam, which is inversely proportional to the largest baseline. The finite rate of innovation (FRI) framework is a robust method to find the locations of point-sources in a continuum without grid imposition. The continuous formulation makes the FRI recovery performance only dependent on the number of measurements and the number of sources in the sky. FRI can theoretically find sources below the perceived tool resolution. To date, FRI had never been tested in the extreme conditions inherent to radio astronomy: weak signal / high noise, huge data sets, large numbers of sources. Aims: The aims were (i) to adapt FRI to radio astronomy, (ii) verify it can recover sources in radio astronomy conditions with more accurate positioning than CLEAN, and possibly resolve some sources that would otherwise be missed, (iii) show that sources can be found using less data than would otherwise be required to find them, and (iv) show that FRI does not lead to an augmented rate of false positives. Methods: We implemented a continuous domain sparse reconstruction algorithm in Python. The angular resolution performance of the new algorithm was assessed under simulation, and with visibility measurements from the LOFAR telescope. Existing catalogs were used to confirm the existence of sources. Results: We adapted the FRI framework to radio interferometry, and showed that it is possible to determine accurate off-grid point-source locations and their corresponding intensities. In addition, FRI-based sparse reconstruction required less integration time and smaller baselines to reach a comparable reconstruction quality compared to a conventional method. The achieved angular resolution is higher than the perceived instrument resolution, and very close sources can be reliably distinguished. The proposed approach has cubic complexity in the total number (typically around a few thousand) of uniform Fourier data of the sky image estimated from the reconstruction. It is also demonstrated that the method is robust to the presence of extended-sources, and that false-positives can be addressed by choosing an adequate model order to match the noise level.

Sources and Delivery of Nutrients to the Northwestern Gulf of Mexico from Streams in the South-Central United States1

PubMed Central

Rebich, Richard A; Houston, Natalie A; Mize, Scott V; Pearson, Daniel K; Ging, Patricia B; Evan Hornig, C

2011-01-01

Abstract SPAtially Referenced Regressions On Watershed attributes (SPARROW) models were developed to estimate nutrient inputs [total nitrogen (TN) and total phosphorus (TP)] to the northwestern part of the Gulf of Mexico from streams in the South-Central United States (U.S.). This area included drainages of the Lower Mississippi, Arkansas-White-Red, and Texas-Gulf hydrologic regions. The models were standardized to reflect nutrient sources and stream conditions during 2002. Model predictions of nutrient loads (mass per time) and yields (mass per area per time) generally were greatest in streams in the eastern part of the region and along reaches near the Texas and Louisiana shoreline. The Mississippi River and Atchafalaya River watersheds, which drain nearly two-thirds of the conterminous U.S., delivered the largest nutrient loads to the Gulf of Mexico, as expected. However, the three largest delivered TN yields were from the Trinity River/Galveston Bay, Calcasieu River, and Aransas River watersheds, while the three largest delivered TP yields were from the Calcasieu River, Mermentau River, and Trinity River/Galveston Bay watersheds. Model output indicated that the three largest sources of nitrogen from the region were atmospheric deposition (42%), commercial fertilizer (20%), and livestock manure (unconfined, 17%). The three largest sources of phosphorus were commercial fertilizer (28%), urban runoff (23%), and livestock manure (confined and unconfined, 23%). PMID:22457582

A method for reducing the largest relative errors in Monte Carlo iterated-fission-source calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hunter, J. L.; Sutton, T. M.

2013-07-01

In Monte Carlo iterated-fission-source calculations relative uncertainties on local tallies tend to be larger in lower-power regions and smaller in higher-power regions. Reducing the largest uncertainties to an acceptable level simply by running a larger number of neutron histories is often prohibitively expensive. The uniform fission site method has been developed to yield a more spatially-uniform distribution of relative uncertainties. This is accomplished by biasing the density of fission neutron source sites while not biasing the solution. The method is integrated into the source iteration process, and does not require any auxiliary forward or adjoint calculations. For a given amountmore » of computational effort, the use of the method results in a reduction of the largest uncertainties relative to the standard algorithm. Two variants of the method have been implemented and tested. Both have been shown to be effective. (authors)« less

Vision in the deep sea.

PubMed

Warrant, Eric J; Locket, N Adam

2004-08-01

The deep sea is the largest habitat on earth. Its three great faunal environments--the twilight mesopelagic zone, the dark bathypelagic zone and the vast flat expanses of the benthic habitat--are home to a rich fauna of vertebrates and invertebrates. In the mesopelagic zone (150-1000 m), the down-welling daylight creates an extended scene that becomes increasingly dimmer and bluer with depth. The available daylight also originates increasingly from vertically above, and bioluminescent point-source flashes, well contrasted against the dim background daylight, become increasingly visible. In the bathypelagic zone below 1000 m no daylight remains, and the scene becomes entirely dominated by point-like bioluminescence. This changing nature of visual scenes with depth--from extended source to point source--has had a profound effect on the designs of deep-sea eyes, both optically and neurally, a fact that until recently was not fully appreciated. Recent measurements of the sensitivity and spatial resolution of deep-sea eyes--particularly from the camera eyes of fishes and cephalopods and the compound eyes of crustaceans--reveal that ocular designs are well matched to the nature of the visual scene at any given depth. This match between eye design and visual scene is the subject of this review. The greatest variation in eye design is found in the mesopelagic zone, where dim down-welling daylight and bio-luminescent point sources may be visible simultaneously. Some mesopelagic eyes rely on spatial and temporal summation to increase sensitivity to a dim extended scene, while others sacrifice this sensitivity to localise pinpoints of bright bioluminescence. Yet other eyes have retinal regions separately specialised for each type of light. In the bathypelagic zone, eyes generally get smaller and therefore less sensitive to point sources with increasing depth. In fishes, this insensitivity, combined with surprisingly high spatial resolution, is very well adapted to the detection and localisation of point-source bioluminescence at ecologically meaningful distances. At all depths, the eyes of animals active on and over the nutrient-rich sea floor are generally larger than the eyes of pelagic species. In fishes, the retinal ganglion cells are also frequently arranged in a horizontal visual streak, an adaptation for viewing the wide flat horizon of the sea floor, and all animals living there. These and many other aspects of light and vision in the deep sea are reviewed in support of the following conclusion: it is not only the intensity of light at different depths, but also its distribution in space, which has been a major force in the evolution of deep-sea vision.

Emission factors for open and domestic biomass burning for use in atmospheric models

Treesearch

S. K. Akagi; R. J. Yokelson; C. Wiedinmyer; M. J. Alvarado; J. S. Reid; T. Karl; J. D. Crounse; P. O. Wennberg

2010-01-01

Biomass burning (BB) is the second largest source of trace gases and the largest source of primary fine carbonaceous particles in the global troposphere. Many recent BB studies have provided new emission factor (EF) measurements. This is especially 5 true for non methane organic compounds (NMOC), which influence secondary organic aerosol (SOA) and ozone formation. New...

Uncertainty in gridded CO 2 emissions estimates

DOE PAGES

Hogue, Susannah; Marland, Eric; Andres, Robert J.; ...

2016-05-19

We are interested in the spatial distribution of fossil-fuel-related emissions of CO 2 for both geochemical and geopolitical reasons, but it is important to understand the uncertainty that exists in spatially explicit emissions estimates. Working from one of the widely used gridded data sets of CO 2 emissions, we examine the elements of uncertainty, focusing on gridded data for the United States at the scale of 1° latitude by 1° longitude. Uncertainty is introduced in the magnitude of total United States emissions, the magnitude and location of large point sources, the magnitude and distribution of non-point sources, and from themore » use of proxy data to characterize emissions. For the United States, we develop estimates of the contribution of each component of uncertainty. At 1° resolution, in most grid cells, the largest contribution to uncertainty comes from how well the distribution of the proxy (in this case population density) represents the distribution of emissions. In other grid cells, the magnitude and location of large point sources make the major contribution to uncertainty. Uncertainty in population density can be important where a large gradient in population density occurs near a grid cell boundary. Uncertainty is strongly scale-dependent with uncertainty increasing as grid size decreases. In conclusion, uncertainty for our data set with 1° grid cells for the United States is typically on the order of ±150%, but this is perhaps not excessive in a data set where emissions per grid cell vary over 8 orders of magnitude.« less

An X-ray Investigation of the NGC 346 Field in the SMC (2): The Field Population

NASA Technical Reports Server (NTRS)

Naze, Y.; Hartwell, J. M.; Stevens, I. R.; Manfroid, J.; Marchenko, S.; Corcoran, M. F.; Moffat, A. F. J.; Skalkowski, G.

2003-01-01

We present results from a Chandra observation of the NGC 346 cluster, which is the ionizing source of N66, the most luminous HII region and the largest star formation region in the SMC. In the first part of this investigation, we have analysed the X-ray properties of the cluster itself and the remarkable star HD 5980. But the field contains additional objects of interest. In total, 79 X-ray point sources were detected in the Chandra observation: this is more than five times the number of sources detected by previous X-ray surveys. We investigate here their characteristics in detail. The sources possess rather high hardness ratios, and their cumulative luminosity function is steeper than that for the rest of the SMC at higher .luminosities. Their absorption columns suggest that most of the sources belong to NGC346. Using new UBV RI imaging with the ESO 2.2m telescope, we also discovered possible counterparts for 36 of these X-ray sources and estimated a B spectral type for a large number of these counterparts. This tends to suggest that most of the X-ray sources in the field are in fact X-ray binaries. Finally, some objects show X-ray and/or optical variability, with a need for further monitoring.

TU-AB-BRC-11: Moving a GPU-OpenCL-Based Monte Carlo (MC) Dose Engine Towards Routine Clinical Use: Automatic Beam Commissioning and Efficient Source Sampling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tian, Z; Folkerts, M; Jiang, S

Purpose: We have previously developed a GPU-OpenCL-based MC dose engine named goMC with built-in analytical linac beam model. To move goMC towards routine clinical use, we have developed an automatic beam-commissioning method, and an efficient source sampling strategy to facilitate dose calculations for real treatment plans. Methods: Our commissioning method is to automatically adjust the relative weights among the sub-sources, through an optimization process minimizing the discrepancies between calculated dose and measurements. Six models built for Varian Truebeam linac photon beams (6MV, 10MV, 15MV, 18MV, 6MVFFF, 10MVFFF) were commissioned using measurement data acquired at our institution. To facilitate dose calculationsmore » for real treatment plans, we employed inverse sampling method to efficiently incorporate MLC leaf-sequencing into source sampling. Specifically, instead of sampling source particles control-point by control-point and rejecting the particles blocked by MLC, we assigned a control-point index to each sampled source particle, according to MLC leaf-open duration of each control-point at the pixel where the particle intersects the iso-center plane. Results: Our auto-commissioning method decreased distance-to-agreement (DTA) of depth dose at build-up regions by 36.2% averagely, making it within 1mm. Lateral profiles were better matched for all beams, with biggest improvement found at 15MV for which root-mean-square difference was reduced from 1.44% to 0.50%. Maximum differences of output factors were reduced to less than 0.7% for all beams, with largest decrease being from1.70% to 0.37% found at 10FFF. Our new sampling strategy was tested on a Head&Neck VMAT patient case. Achieving clinically acceptable accuracy, the new strategy could reduce the required history number by a factor of ∼2.8 given a statistical uncertainty level and hence achieve a similar speed-up factor. Conclusion: Our studies have demonstrated the feasibility and effectiveness of our auto-commissioning approach and new efficient source sampling strategy, implying the potential of our GPU-based MC dose engine goMC for routine clinical use.« less

Nitrate concentrations under irrigated agriculture

USGS Publications Warehouse

Zaporozec, A.

1983-01-01

In recent years, considerable interest has been expressed in the nitrate content of water supplies. The most notable toxic effect of nitrate is infant methemoglobinemia. The risk of this disease increases significantly at nitrate-nitrogen levels exceeding 10 mg/l. For this reason, this concentration has been established as a limit for drinking water in many countries. In natural waters, nitrate is a minor ionic constituent and seldom accounts for more than a few percent of the total anions. However, nitrate in a significant concentration may occur in the vicinity of some point sources such as septic tanks, manure pits, and waste-disposal sites. Non-point sources contributing to groundwater pollution are numerous and a majority of them are related to agricultural activities. The largest single anthropogenic input of nitrate into the groundwater is fertilizer. Even though it has not been proven that nitrogen fertilizers are responsible for much of nitrate pollution, they are generally recognized as the main threat to groundwater quality, especially when inefficiently applied to irrigated fields on sandy soils. The biggest challenge facing today's agriculture is to maintain the balance between the enhancement of crop productivity and the risk of groundwater pollution. ?? 1982 Springer-Verlag New York Inc.

Coastal aquifers: Scientific advances in the face of global environmental challenges

NASA Astrophysics Data System (ADS)

Post, Vincent E. A.; Werner, Adrian D.

2017-08-01

Coastal aquifers embody the subsurface transition between terrestrial and marine systems, and form the almost invisible pathway for tremendous volumes of freshwater that flow to the ocean. Changing conditions of the earth's landscapes and oceans can disrupt the fragile natural equilibrium between fresh and saltwater that exists in coastal zones. Among these, over-abstraction of groundwater is considered the leading man-made cause of seawater intrusion. Moreover, many of the world's largest urban settings, where sources of contamination are profuse, have been built over the freshwater in coastal aquifers. Thus, coastal aquifers are important receptors of human impacts to water on Earth (Michael et al., 2017). This Special Issue on 'Investigation and Management of Coastal Aquifers' contains current scientific advances on the topic, dealing with the storage and quality of water, affected by stressors ranging in scale from point source contamination to global climate change.

Non-agricultural ammonia emissions in urban China

NASA Astrophysics Data System (ADS)

Chang, Y. H.

2014-03-01

The non-agricultural ammonia (NH3) emissions in cities have received little attention but could rival agricultural sources in term of the efficiency in PM formation. The starting point for finding credible solutions is to comprehensively establish a city-specific Non-agricultural Ammonia Emission Inventory (NAEI) and identify the largest sources where efforts can be directed to deliver the largest impact. In this paper, I present a NAEI of 113 national key cities targeted on environmental protection in China in 2010, which for the first time covers NH3 emissions from pets, infants, smokers, green land, and household products. Results show that totally 210 478 Mg, the NH3 emissions from traffic, fuel combustion, waste disposal, pets, green land, human, and household products are 67 671 Mg, 56 275 Mg, 44 289 Mg, 23 355 Mg, 7509 Mg, 7312 Mg, and 4069 Mg, respectively. The NH3 emission intensity from the municipal districts ranges from 0.08 to 3.13 Mg km-2 yr-1, with a average of 0.84 Mg km-2 yr-1. The high NH3 emission intensities in Beijing-Tianjin-Hebei region, Yangtze River Delta region and Pearl River Delta region support the view that non-agricultural NH3 sources play a key role in city-scale NH3 emissions and thus have potentially important implications for secondary PM formation (ammonium-sulfate-nitrate system) in urban agglomeration of China. Therefore, in addition to current SO2 and NOx controls, China also needs to allocate more scientific, technical, and legal resources on controlling non-agricultural NH3 emissions in the future.

THE PANCHROMATIC HUBBLE ANDROMEDA TREASURY. X. ULTRAVIOLET TO INFRARED PHOTOMETRY OF 117 MILLION EQUIDISTANT STARS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Benjamin F.; Dalcanton, Julianne J.; Weisz, Daniel R.

We have measured stellar photometry with the Hubble Space Telescope Wide Field Camera 3 (WFC3) and Advanced Camera for Surveys in near ultraviolet (F275W, F336W), optical (F475W, F814W), and near infrared (F110W, F160W) bands for 117 million resolved stars in M31. As part of the Panchromatic Hubble Andromeda Treasury survey, we measured photometry with simultaneous point-spread function (PSF) fitting across all bands and at all source positions after precise astrometric image alignment (<5-10 mas accuracy). In the outer disk, the photometry reaches a completeness-limited depth of F475W ∼ 28, while in the crowded, high surface brightness bulge, the photometry reachesmore » F475W ∼ 25. We find that simultaneous photometry and optimized measurement parameters significantly increase the detection limit of the lowest-resolution filters (WFC3/IR) providing color-magnitude diagrams (CMDs) that are up to 2.5 mag deeper when compared with CMDs from WFC3/IR photometry alone. We present extensive analysis of the data quality including comparisons of luminosity functions and repeat measurements, and we use artificial star tests to quantify photometric completeness, uncertainties and biases. We find that the largest sources of systematic error in the photometry are due to spatial variations in the PSF models and charge transfer efficiency corrections. This stellar catalog is the largest ever produced for equidistant sources, and is publicly available for download by the community.« less

Explosion-induced stress changes estimated from vibrating-wire stressmeter measurements near the Mighty Epic event, Nevada Test Site

USGS Publications Warehouse

Ellis, William L.; Kibler, J.D.

1983-01-01

Explosion-induced compressive stress increases near an underground nuclear explosion are believed to contribute significantly to the containment of high-pressure gases within the explosion-produced cavity. These induced compressive stresses are predicted by computer calculations, but have never been adequately confirmed by field measurements, owing primarily to the unique difficulties of obtaining such field data. Vibrating-wire stressmeter measurements made near the Mighty Epic nuclear detonation, however, qualitatively indicate that within 150 meters of the working point, permanent compressive stress increases of several megapascals were present 15 weeks after the event. Additionally, stress-change magnitudes interpreted from the stressmeter data between the 75- and 260-meter range from the working point compare favorably with calculational predictions of the stress changes believed to be present shortly after detonation of the event. The measurements and calculations differ, however, with regard to the pattern of stress change radial and transverse to the explosion source. For the range of the field measurements from the working point, computer models predict the largest compressive-stress increase to be radial to the explosion source, while the field data indicate the transverse component of. stress change to be the most compressive. The significance of time-dependent modification of the initial explosion-induced stress distribution is, however, uncertain with regard to the comparison of the field measurements and theoretical predictions.

Trail Creek II: Modeling Flow and E. Coli Concentrations in a Small Urban Stream using SWAT

NASA Astrophysics Data System (ADS)

Radcliffe, D. E.; Saintil, T.

2017-12-01

Pathogens are one of the leading causes of stream and river impairment in the State of Georgia. The common presence of fecal bacteria is driven by several factors including rapid population growth stressing pre-existing and ageing infrastructure, urbanization and poor planning, increase percent imperviousness, urban runoff, municipal discharges, sewage, pet/wildlife waste and leaky septic tanks. The Trail Creek watershed, located in Athens-Clarke County, Georgia covers about 33 km2. Stream segments within Trail Creek violate the GA standard due to high levels of fecal coliform bacteria. In this study, the Soil and Water Assessment Tool (SWAT) modeling software was used to predict E. coli bacteria concentrations during baseflow and stormflow. Census data from the county was used for human and animal population estimates and the Fecal Indicator Tool to generate the number of colony forming units of E. Coli for each source. The model was calibrated at a daily time step with one year of monitored streamflow and E. coli bacteria data using SWAT-CUP and the SUFI2 algorithm. To simulate leaking sewer lines, we added point sources in the five subbasins in the SWAT model with the greatest length of sewer line within 50 m of the stream. The flow in the point sources were set to 5% of the stream flow and the bacteria count set to that of raw sewage (30,000 cfu/100 mL). The calibrated model showed that the average load during 2003-2013 at the watershed outlet was 13 million cfu per month. Using the calibrated model, we simulated scenarios that assumed leaking sewers were repaired in one of the five subbasins with point sources. The reduction ranged from 10 to 46%, with the largest reduction in subbasin in the downtown area. Future modeling work will focus on the use of green infrastructure to address sources of bacteria.

Lesson and Impressions of the Ghanaian Capital Markets

DTIC Science & Technology

2011-07-31

Gold and cocoa production are major sources of foreign exchange. Interestingly, the country’s largest source of foreign exchange is remittances from...workers abroad. Oil production has expanded. According to industry experts, within 5 years, Ghana is likely to be the third-largest producer of oil...State Department reports the most prominent industries include textiles, apparel, steel, tires, flour milling, cocoa processing, beverages, tobacco

Sources and Delivery of Nutrients to the Northwestern Gulf of Mexico from Streams in the South-Central United States

USGS Publications Warehouse

Rebich, R.A.; Houston, N.A.; Mize, S.V.; Pearson, D.K.; Ging, P.B.; Evan, Hornig C.

2011-01-01

SPAtially Referenced Regressions On Watershed attributes (SPARROW) models were developed to estimate nutrient inputs [total nitrogen (TN) and total phosphorus (TP)] to the northwestern part of the Gulf of Mexico from streams in the South-Central United States (U.S.). This area included drainages of the Lower Mississippi, Arkansas-White-Red, and Texas-Gulf hydrologic regions. The models were standardized to reflect nutrient sources and stream conditions during 2002. Model predictions of nutrient loads (mass per time) and yields (mass per area per time) generally were greatest in streams in the eastern part of the region and along reaches near the Texas and Louisiana shoreline. The Mississippi River and Atchafalaya River watersheds, which drain nearly two-thirds of the conterminous U.S., delivered the largest nutrient loads to the Gulf of Mexico, as expected. However, the three largest delivered TN yields were from the Trinity River/Galveston Bay, Calcasieu River, and Aransas River watersheds, while the three largest delivered TP yields were from the Calcasieu River, Mermentau River, and Trinity River/Galveston Bay watersheds. Model output indicated that the three largest sources of nitrogen from the region were atmospheric deposition (42%), commercial fertilizer (20%), and livestock manure (unconfined, 17%). The three largest sources of phosphorus were commercial fertilizer (28%), urban runoff (23%), and livestock manure (confined and unconfined, 23%). ?? 2011 American Water Resources Association. This article is a U.S. Government work and is in the public domain in the USA.

Effect of Worldwide Oil Price Fluctuations on Biomass Fuel Use and Child Respiratory Health: Evidence from Guatemala

PubMed Central

Fried, Brian J.

2011-01-01

Objectives. We examined the effect of worldwide oil price fluctuations on household fuel use and child respiratory health in Guatemala. Methods. We regressed measures of household fuel use and child respiratory health on the average worldwide oil price and a rich set of covariates. We leveraged variation in oil prices over the 6-month period of the survey to identify associations between fuel prices, fuel choice, and child respiratory outcomes. Results. A $1 (3.4% point) increase in worldwide fuel prices was associated with a 2.8% point decrease in liquid propane gasoline use (P < .05), a 0.75% point increase in wood use (P < .05), and a 1.5% point increase in the likelihood of the child reporting a respiratory symptom (P < .1). The association between oil prices and the fuel choice indicators was largest for households in the middle of the income distribution. Conclusions. Fluctuations in worldwide fuel prices affected household fuel use and, consequently, child health. Policies to help households tide over fuel price shocks or reduce pollution from biomass sources would confer positive health benefits. Such policies would be most effective if they targeted both poor and middle-income households. PMID:21778480

Sources of heavy metals in urban wastewater in Stockholm.

PubMed

Sörme, L; Lagerkvist, R

2002-10-21

The sources of heavy metals to a wastewater treatment plant was investigated. Sources can be actual goods, e.g. runoff from roofs, wear of tires, food, or activities, e.g. large enterprises, car washes. The sources were identified by knowing the metals content in various goods and the emissions from goods to sewage or stormwater. The sources of sewage water and stormwater were categorized to enable comparison with other research and measurements. The categories were households, drainage water, businesses, pipe sediment (all transported in sewage water), atmospheric deposition, traffic, building materials and pipe sediment (transported in stormwater). Results show that it was possible to track the sources of heavy metals for some metals such as Cu and Zn (110 and 100% found, respectively) as well as Ni and Hg (70% found). Other metals sources are still poorly understood or underestimated (Cd 60%, Pb 50%, Cr 20% known). The largest sources of Cu were tap water and roofs. For Zn the largest sources were galvanized material and car washes. In the case of Ni, the largest sources were chemicals used in the WTP and drinking water itself. And finally, for Hg the most dominant emission source was the amalgam in teeth. For Pb, Cr and Cd, where sources were more poorly understood, the largest contributors for all were car washes. Estimated results of sources from this study were compared with previously done measurements. The comparison shows that measured contribution from households is higher than that estimated (except Hg), leading to the conclusion that the sources of sewage water from households are still poorly understood or that known sources are underestimated. In the case of stormwater, the estimated contributions are rather well in agreement with measured contributions, although uncertainties are large for both estimations and measurements. Existing pipe sediments in the plumbing system, which release Hg and Pb, could be one explanation for the missing amount of these metals. Large enterprises were found to make a very small contribution, 4% or less for all metals studied. Smaller enterprises (with the exception of car washes) have been shown to make a small contribution in another city; the contribution in this case study is still unknown.

The gamma ray north-south effect

NASA Technical Reports Server (NTRS)

White, R. S.; O'Neill, T. J.; Tumer, O. T.; Zych, A. D.

1988-01-01

Theoretical calculations are presented that explain the balloon observations by O'Neill et al. (1987) of a strong north-south anisotropy of atmospheric gamma rays over the Southern Hemisphere, and to predict the north-south ratios. It is shown that the gamma rays that originate at the longest distances from the telescopes give the largest north-south ratios. Comparisons are made of the experimental north-south ratios measured on balloons launched from Alice Springs, Australia, and from Palestine, Texas, U.S., and predictions are made for ratios at other geomagnetic latitudes and longitudes. It is pointed out that observers who measure backgrounds for celestial sources may be misled unless they correct for the north-south effect.

NASA's SDO Observes Largest Sunspot of the Solar Cycle

NASA Image and Video Library

2017-12-08

On Oct. 18, 2014, a sunspot rotated over the left side of the sun, and soon grew to be the largest active region seen in the current solar cycle, which began in 2008. Currently, the sunspot is almost 80,000 miles across -- ten Earth's could be laid across its diameter. Sunspots point to relatively cooler areas on the sun with intense and complex magnetic fields poking out through the sun's surface. Such areas can be the source of solar eruptions such as flares or coronal mass ejections. So far, this active region – labeled AR 12192 -- has produced several significant solar flares: an X-class flare on Oct. 19, an M-class flare on Oct. 21, and an X-class flare on Oct. 22, 2014. The largest sunspot on record occurred in 1947 and was almost three times as large as the current one. Active regions are more common at the moment as we are in what's called solar maximum, which is the peak of the sun's activity, occurring approximately every 11 years. Credit: NASA/SDO NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Chemical characteristics of North American surface layer outflow: Insights from Chebogue Point, Nova Scotia

NASA Astrophysics Data System (ADS)

Millet, Dylan B.; Goldstein, Allen H.; Holzinger, Rupert; Williams, Brent J.; Allan, James D.; Jimenez, José L.; Worsnop, Douglas R.; Roberts, James M.; White, Allen B.; Hudman, Rynda C.; Bertschi, Isaac T.; Stohl, Andreas

2006-12-01

We present a factor analysis-based method for differentiating air masses on the basis of source influence and apply the method to a broad suite of trace gas and aerosol measurements collected at Chebogue Point, Nova Scotia, during the summer of 2004 to characterize the chemical composition of atmospheric outflow from eastern North America. CO, ozone, and aerosol mass were elevated by 30%, 56%, and more than 300% at Chebogue Point during U.S. outflow periods. Organic aerosol mass was highest during U.S. pollution events, but made up the largest fraction (70%) of the total aerosol during periods of primary and especially secondary biogenic influence, indicating the importance of both anthropogenic and biogenic organic aerosol. Anthropogenic and oxygenated volatile organic compounds account for the bulk of the gas-phase organic carbon under most conditions; however, biogenic compounds are important in terms of chemical reactivity. Biogenic emissions thus have a significant impact on the chemistry of air masses downwind of the polluted northeastern United States. Using output from a global 3-D model of atmospheric composition (GEOS-Chem), we estimate that CO directly emitted from U.S. pollution sources makes up 28% of the total CO observed at Chebogue Point during U.S. outflow events and 19% at other times, although more work is needed to improve U.S. emission estimates for CO and other pollutants. We conclude that the effects of North American pollution on the chemistry of the western North Atlantic boundary layer are pervasive and not restricted to particular events.

Source apportionment of ambient volatile organic compounds in the Pearl River Delta, China: Part II

NASA Astrophysics Data System (ADS)

Liu, Ying; Shao, Min; Lu, Sihua; Chang, Chih-Chung; Wang, Jia-Lin; Fu, Linlin

The chemical mass balance receptor model was applied to the source apportionment of 58 hydrocarbons measured at seven sites in a field campaign that examined regional air quality in the Pearl River Delta (PRD) region in the fall of 2004. A total of 12 volatile organic compound (VOC) emission sources were considered, including gasoline- and diesel-powered vehicle exhausts, headspace vapors of gasoline and diesel fuel, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, paint vapors, asphalt emissions from paved roads, biomass combustion, coal combustion, the chemical industry, and petroleum refineries. Vehicle exhaust was the largest source of VOCs, contributing to >50% of ambient VOCs at the three urban sites (Guangzhou, Foshan, and Zhongshan). LPG leakage played an important role, representing 8-16% of emissions at most sites in the PRD. Solvent usage was the biggest emitter of VOCs at Dongguan, an industrial site, contributing 33% of ambient VOCs. Similarly, at Xinken, a non-urban site, the evaporation of solvents and coatings was the largest emission source, accounting for 31% of emissions, probably because it was downwind of Dongguan. Local biomass combustion was a noticeable source of VOCs at Xinken; although its contribution was estimated at 14.3%, biomass combustion was the third largest VOC source at this site.

Long-period Ground Motion Simulation in the Osaka Basin during the 2011 Great Tohoku Earthquake

NASA Astrophysics Data System (ADS)

Iwata, T.; Kubo, H.; Asano, K.; Sato, K.; Aoi, S.

2014-12-01

Large amplitude long-period ground motions (1-10s) with long duration were observed in the Osaka sedimentary basin during the 2011 Tohoku earthquake (Mw9.0) and its aftershock (Ibaraki-Oki, Mw7.7), which is about 600 km away from the source regions. Sato et al. (2013) analyzed strong ground motion records from the source region to the Osaka basin and showed the following characteristics. (1) In the period range of 1 to 10s, the amplitude of horizontal components of the ground motion at the site-specific period is amplified in the Osaka basin sites. The predominant period is about 7s in the bay area where the largest pSv were observed. (2) The velocity Fourier amplitude spectra with their predominant period of around 7s are observed at the bedrock sites surrounding the Osaka basin. Those characteristics were observed during both of the mainshock and the largest aftershock. Therefore, large long-period ground motions in the Osaka basin are generated by the combination of propagation-path and basin effects. They simulated ground motions due to the largest aftershock as a simple point source model using three-dimensional FDM (GMS; Aoi and Fujiwara, 1999). They used a three-dimensional velocity structure based on the Japan Integrated Velocity Structure Model (JIVSM, Koketsu et al., 2012), with the minimum effective period of the computation of 3s. Their simulation result reproduced the observation characteristics well and it validates the applicability of the JIVSM for the long period ground motion simulation. In this study, we try to simulate long-period ground motions during the mainshock. The source model we used for the simulation is based on the SMGA model obtained by Asano and Iwata (2012). We succeed to simulate long-period ground motion propagation from Kanto area to the Osaka basin fairly well. The long-period ground motion simulations with the several Osaka basin velocity structure models are done for improving the model applicability. We used strong motion data recorded by K-NET, KiK-net and F-net of NIED, CEORKA, BRI, JMA, Osaka city waterworks bureau, and Osaka prefecture. GMS provided by NIED is used for the computation.

Response of Polish rivers (Vistula, Oder) to reduced pressure from point sources and agriculture during the transition period (1988-2008)

NASA Astrophysics Data System (ADS)

Pastuszak, Marianna; Stålnacke, Per; Pawlikowski, Krzysztof; Witek, Zbigniew

2012-06-01

The Vistula and Oder Rivers, two out of the seven largest rivers in the Baltic drainage basin, were responsible for 25% of total riverine nitrogen (TN) and 37% of total riverine phosphorus (TP) input to the Baltic Sea in 2000. The aim of this paper is to evaluate the response of these two rivers to changes that took place in Polish economy during the transition period (1988-2008). The economic changes encompassed: construction of nearly 900 waste water treatment plants in 1999-2008, modernization or closure of obsolete factories, economizing in water consumption, closure or change of ownership of State-owned farms, a drop in fertilizer application, and a decline in livestock stocking. More intensive agriculture and higher point source emissions in the Oder than in the Vistula basin resulted in higher concentrations of TN, nitrate (NO3-N), and TP in the Oder waters in the entire period of our studies. In both rivers, nutrient concentrations and loads showed significant declining trends in the period 1988-2008. TN loads decreased by ca. 20% and 25% in the Vistula and Oder; TP loads dropped by ca. 15% and 65% in the Vistula and Oder. The reduction in phosphorus loads was particularly pronounced in the Oder basin, which was characterized by efficient management systems aiming at mitigation of nutrient emission from the point sources and greater extent of structural changes in agricultural sector during the transition period. The trends in riverine loads are discussed in the paper in relation to socio-economical changes during the transition period, and with respect to physiographic features.

Safe drinking water and waterborne outbreaks.

PubMed

Moreira, N A; Bondelind, M

2017-02-01

The present work compiles a review on drinking waterborne outbreaks, with the perspective of production and distribution of microbiologically safe water, during 2000-2014. The outbreaks are categorised in raw water contamination, treatment deficiencies and distribution network failure. The main causes for contamination were: for groundwater, intrusion of animal faeces or wastewater due to heavy rain; in surface water, discharge of wastewater into the water source and increased turbidity and colour; at treatment plants, malfunctioning of the disinfection equipment; and for distribution systems, cross-connections, pipe breaks and wastewater intrusion into the network. Pathogens causing the largest number of affected consumers were Cryptosporidium, norovirus, Giardia, Campylobacter, and rotavirus. The largest number of different pathogens was found for the treatment works and the distribution network. The largest number of affected consumers with gastrointestinal illness was for contamination events from a surface water source, while the largest number of individual events occurred for the distribution network.

Mechanical coupling between earthquakes and volcanoes inferred from stress transfer models: evidence from Vesuvio, Etna and Alban Hills (Italy)

NASA Astrophysics Data System (ADS)

Cocco, M.; Feuillet, N.; Nostro, C.; Musumeci, C.

2003-04-01

We investigate the mechanical interactions between tectonic faults and volcanic sources through elastic stress transfer and discuss the results of several applications to Italian active volcanoes. We first present the stress modeling results that point out a two-way coupling between Vesuvius eruptions and historical earthquakes in Southern Apennines, which allow us to provide a physical interpretation of their statistical correlation. Therefore, we explore the elastic stress interaction between historical eruptions at the Etna volcano and the largest earthquakes in Eastern Sicily and Calabria. We show that the large 1693 seismic event caused an increase of compressive stress along the rift zone, which can be associated to the lack of flank eruptions of the Etna volcano for about 70 years after the earthquake. Moreover, the largest Etna eruptions preceded by few decades the large 1693 seismic event. Our modeling results clearly suggest that all these catastrophic events are tectonically coupled. We also investigate the effect of elastic stress perturbations on the instrumental seismicity caused by magma inflation at depth both at the Etna and at the Alban Hills volcanoes. In particular, we model the seismicity pattern at the Alban Hills volcano (central Italy) during a seismic swarm occurred in 1989-90 and we interpret it in terms of Coulomb stress changes caused by magmatic processes in an extensional tectonic stress field. We verify that the earthquakes occur in areas of Coulomb stress increase and that their faulting mechanisms are consistent with the stress perturbation induced by the volcanic source. Our results suggest a link between faults and volcanic sources, which we interpret as a tectonic coupling explaining the seismicity in a large area surrounding the volcanoes.

Meridional distribution of molecular hydrogen and its deuterium content in the atmosphere

NASA Astrophysics Data System (ADS)

Rice, Andrew; Quay, Paul; Stutsman, Johnny; Gammon, Richard; Price, Heather; Jaeglé, Lyatt

2010-06-01

The atmospheric molecular hydrogen concentration and its deuterium abundance were measured in remote air samples collected onboard six Pacific Ocean ship transects between 37°N and 77°S during years 2001 through 2005. The data reveal a year-round interhemispheric gradient in H2 concentration and isotopic composition with the extratropical Northern Hemisphere lower in H2 concentration by 17 ± 11 ppb and δD of H2 by 16 ± 12‰ than the Southern Hemisphere (95% confidence). On the basis of these snapshots, the interhemispheric gradient in δD was observed to be smallest in September through November, a time that experiences the largest gradient in concentration, and the largest in April, a time that has a small gradient in concentration. A simple hemispheric box model of the atmosphere indicates that, while the hemispheric asymmetry in soil sink of H2 is primarily responsible for the observed interhemispheric gradient in H2 concentration, the hemispheric difference in the δD of the H2 sources and sinks are equally responsible for the observed interhemispheric gradient in δD. Both the inverse correlation between interhemispheric H2 and δD gradients and their seasonal changes point to the importance of the H2 produced by photochemical sources. Comparisons with a three-dimensional chemical transport model shows reasonable agreement with mean behavior in both variables and provides an accounting for H2 sources and sinks within ±15% without a dramatic change in the H2 budget. Anomalous H2 concentrations and δD in tropics and low-latitude regions observed during the November-December 2001 meridional H2 and δD snapshot is thought to be a result of H2 emissions from biomass burning, possibly from continental Africa.

New empirically-derived solar radiation pressure model for GPS satellites

NASA Technical Reports Server (NTRS)

Bar-Sever, Y.; Kuang, D.

2003-01-01

Solar radiation pressure force is the second largest perturbation acting on GPS satellites, after the gravitational attraction from the Earth, Sun, and Moon. It is the largest error source in the modeling of GPS orbital dynamics.

Application of the SPARROW model to assess surface-water nutrient conditions and sources in the United States Pacific Northwest

USGS Publications Warehouse

Wise, Daniel R.; Johnson, Henry M.

2013-01-01

The watershed model SPARROW (Spatially Referenced Regressions on Watershed attributes) was used to estimate mean annual surface-water nutrient conditions (total nitrogen and total phosphorus) and to identify important nutrient sources in catchments of the Pacific Northwest region of the United States for 2002. Model-estimated nutrient yields were generally higher in catchments on the wetter, western side of the Cascade Range than in catchments on the drier, eastern side. The largest source of locally generated total nitrogen stream load in most catchments was runoff from forestland, whereas the largest source of locally generated total phosphorus stream load in most catchments was either geologic material or livestock manure (primarily from grazing livestock). However, the highest total nitrogen and total phosphorus yields were predicted in the relatively small number of catchments where urban sources were the largest contributor to local stream load. Two examples are presented that show how SPARROW results can be applied to large rivers—the relative contribution of different nutrient sources to the total nitrogen load in the Willamette River and the total phosphorus load in the Snake River. The results from this study provided an understanding of the regional patterns in surface-water nutrient conditions and should be useful to researchers and water-quality managers performing local nutrient assessments.

Sources and distribution of microplastics in China's largest inland lake - Qinghai Lake.

PubMed

Xiong, Xiong; Zhang, Kai; Chen, Xianchuan; Shi, Huahong; Luo, Ze; Wu, Chenxi

2018-04-01

Microplastic pollution was studied in China's largest inland lake - Qinghai Lake in this work. Microplastics were detected with abundance varies from 0.05 × 10 5 to 7.58 × 10 5 items km -2 in the lake surface water, 0.03 × 10 5 to 0.31 × 10 5 items km -2 in the inflowing rivers, 50 to 1292 items m -2 in the lakeshore sediment, and 2 to 15 items per individual in the fish samples, respectively. Small microplastics (0.1-0.5 mm) dominated in the lake surface water while large microplastics (1-5 mm) are more abundant in the river samples. Microplastics were predominantly in sheet and fiber shapes in the lake and river water samples but were more diverse in the lakeshore sediment samples. Polymer types of microplastics were mainly polyethylene (PE) and polypropylene (PP) as identified using Raman Spectroscopy. Spatially, microplastic abundance was the highest in the central part of the lake, likely due to the transport of lake current. Based on the higher abundance of microplastics near the tourist access points, plastic wastes from tourism are considered as an important source of microplastics in Qinghai Lake. As an important area for wildlife conservation, better waste management practice should be implemented, and waste disposal and recycling infrastructures should be improved for the protection of Qinghai Lake. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ground deposition of liquid droplets released from a point source in the atmospheric surface layer

NASA Astrophysics Data System (ADS)

Panneton, Bernard

1989-01-01

A series of field experiments is presented in which the ground deposition of liquid droplets, 120 and 150 microns in diameter, released from a point source at 7 m above ground level, was measured. A detailed description of the experimental technique is provided, and the results are presented and compared to the predictions of a few models. A new rotating droplet generator is described. Droplets are produced by the forced breakup of capillary liquid jets and droplet coalescence is inhibited by the rotational motion of the spray head. The two dimensional deposition patterns are presented in the form of plots of contours of constant density, normalized arcwise distributions and crosswind integrated distributions. The arcwise distributions follow a Gaussian distribution whose standard deviation is evaluated using a modified Pasquill's technique. Models of the crosswind integrated deposit from Godson, Csanady, Walker, Bache and Sayer, and Wilson et al are evaluated. The results indicate that the Wilson et al random walk model is adequate for predicting the ground deposition of the 150 micron droplets. In one case, where the ratio of the droplet settling velocity to the mean wind speed was largest, Walker's model proved to be adequate. Otherwise, none of the models were acceptable in light of the experimental data.

The Application of Elliptic Cylindrical Phantom in Brachytherapy Dosimetric Study of HDR 192Ir Source

NASA Astrophysics Data System (ADS)

Ahn, Woo Sang; Park, Sung Ho; Jung, Sang Hoon; Choi, Wonsik; Do Ahn, Seung; Shin, Seong Soo

2014-06-01

The purpose of this study is to determine the radial dose function of HDR 192Ir source based on Monte Carlo simulation using elliptic cylindrical phantom, similar to realistic shape of pelvis, in brachytherapy dosimetric study. The elliptic phantom size and shape was determined by analysis of dimensions of pelvis on CT images of 20 patients treated with brachytherapy for cervical cancer. The radial dose function obtained using the elliptic cylindrical water phantom was compared with radial dose functions for different spherical phantom sizes, including the Williamsion's data loaded into conventional planning system. The differences in the radial dose function for the different spherical water phantoms increase with radial distance, r, and the largest differences in the radial dose function appear for the smallest phantom size. The radial dose function of the elliptic cylindrical phantom significantly decreased with radial distance in the vertical direction due to different scatter condition in comparison with the Williamson's data. Considering doses to ICRU rectum and bladder points, doses to reference points can be underestimated up to 1-2% at the distance from 3 to 6 cm. The radial dose function in this study could be used as realistic data for calculating the brachytherapy dosimetry for cervical cancer.

A comprehensive biomass burning emission inventory with high spatial and temporal resolution in China

NASA Astrophysics Data System (ADS)

Zhou, Ying; Xing, Xiaofan; Lang, Jianlei; Chen, Dongsheng; Cheng, Shuiyuan; Wei, Lin; Wei, Xiao; Liu, Chao

2017-02-01

Biomass burning injects many different gases and aerosols into the atmosphere that could have a harmful effect on air quality, climate, and human health. In this study, a comprehensive biomass burning emission inventory including domestic and in-field straw burning, firewood burning, livestock excrement burning, and forest and grassland fires is presented, which was developed for mainland China in 2012 based on county-level activity data, satellite data, and updated source-specific emission factors (EFs). The emission inventory within a 1 × 1 km2 grid was generated using geographical information system (GIS) technology according to source-based spatial surrogates. A range of key information related to emission estimation (e.g. province-specific proportion of domestic and in-field straw burning, detailed firewood burning quantities, uneven temporal distribution coefficient) was obtained from field investigation, systematic combing of the latest research, and regression analysis of statistical data. The established emission inventory includes the major precursors of complex pollution, greenhouse gases, and heavy metal released from biomass burning. The results show that the emissions of SO2, NOx, PM10, PM2.5, NMVOC, NH3, CO, EC, OC, CO2, CH4, and Hg in 2012 are 336.8 Gg, 990.7 Gg, 3728.3 Gg, 3526.7 Gg, 3474.2 Gg, 401.2 Gg, 34 380.4 Gg, 369.7 Gg, 1189.5 Gg, 675 299.0 Gg, 2092.4 Gg, and 4.12 Mg, respectively. Domestic straw burning, in-field straw burning, and firewood burning are identified as the dominant biomass burning sources. The largest contributing source is different for various pollutants. Domestic straw burning is the largest source of biomass burning emissions for all the pollutants considered, except for NH3, EC (firewood), and NOx (in-field straw). Corn, rice, and wheat represent the major crop straws. The combined emission of these three straw types accounts for 80 % of the total straw-burned emissions for each specific pollutant mentioned in this study. As for the straw burning emission of various crops, corn straw burning has the largest contribution to all of the pollutants considered, except for CH4; rice straw burning has highest contribution to CH4 and the second largest contribution to other pollutants, except for SO2, OC, and Hg; wheat straw burning is the second largest contributor to SO2, OC, and Hg and the third largest contributor to other pollutants. Heilongjiang, Shandong, and Henan provinces located in the north-eastern and central-southern regions of China have higher emissions compared to other provinces in China. Gridded emissions, which were obtained through spatial allocation based on the gridded rural population and fire point data from emission inventories at county resolution, could better represent the actual situation. High biomass burning emissions are concentrated in the areas with more agricultural and rural activity. The months of April, May, June, and October account for 65 % of emissions from in-field crop residue burning, while, regarding EC, the emissions in January, February, October, November, and December are relatively higher than other months due to biomass domestic burning in heating season. There are regional differences in the monthly variations of emissions due to the diversity of main planted crops and climatic conditions. Furthermore, PM2.5 component results showed that OC, Cl-, EC, K+, NH4+, elemental K, and SO42- are the main PM2.5 species, accounting for 80 % of the total emissions. The species with relatively high contribution to NMVOC emission include ethylene, propylene, toluene, mp-xylene, and ethyl benzene, which are key species for the formation of secondary air pollution. The detailed biomass burning emission inventory developed by this study could provide useful information for air-quality modelling and could support the development of appropriate pollution-control strategies.

NOx Emissions from Large Point Sources: Variability in Ozone Production, Resulting Health Damages and Economic Costs

NASA Astrophysics Data System (ADS)

Mauzerall, D. L.; Sultan, B.; Kim, N.; Bradford, D.

2004-12-01

We present a proof-of-concept analysis of the measurement of the health damage of ozone (O3) produced from nitrogen oxides (NOx = NO + NO2) emitted by individual large point sources in the eastern United States. We use a regional atmospheric model of the eastern United States, the Comprehensive Air Quality Model with Extensions (CAMx), to quantify the variable impact that a fixed quantity of NOx emitted from individual sources can have on the downwind concentration of surface O3, depending on temperature and local biogenic hydrocarbon emissions. We also examine the dependence of resulting ozone-related health damages on the size of the exposed population. The investigation is relevant to the increasingly widely used "cap and trade" approach to NOx regulation, which presumes that shifts of emissions over time and space, holding the total fixed over the course of the summer O3 season, will have minimal effect on the environmental outcome. By contrast, we show that a shift of a unit of NOx emissions from one place or time to another could result in large changes in the health effects due to ozone formation and exposure. We indicate how the type of modeling carried out here might be used to attach externality-correcting prices to emissions. Charging emitters fees that are commensurate with the damage caused by their NOx emissions would create an incentive for emitters to reduce emissions at times and in locations where they cause the largest damage.

Polarimetric phenomenology in the reflective regime: a case study using polarized hyperspectral data

NASA Astrophysics Data System (ADS)

Gibney, Mark

2016-05-01

Understanding the phenomenology of polarimetric data is necessary if we want to obtain the maximum benefit when we exploit that data. To first order, polarimetric phenomenology is driven by two things; the target material type (specular or diffuse) and the illuminating source (point (sun) or extended (body emission)). Polarimetric phenomenology can then be broken into three basic categories; ([specular material/sun source], [diffuse/sun], [specular/body]) where we have assigned body emission to the IR passband where materials are generally specular. The task of interest determines the category of interest since the task determines the dominant target material and the illuminating source (eg detecting diffuse targets under trees in VNIR = [diffuse/sun] category). In this paper, a specific case study for the important [diffuse/sun] category will be presented. For the reflective regime (0.3 - 3.0um), the largest polarimetric signal is obtained when the sun illuminates a significant portion of the material BRDF lobe. This naturally points us to problems whose primary target materials are diffuse since the BRDF lobe for specular materials is tiny (low probability of acquiring on the BRDF lobe) and glinty (high probability of saturating the sensor when on lobe). In this case study, we investigated signatures of solar illuminated diffuse paints acquired by a polarimetric hyperspectral sensor. We will discuss the acquisition, reduction and exploitation of that data, and use it to illustrate the primary characteristics of reflective polarimetric phenomenology.

[Anthropogenic ammonia emission inventory and characteristics in the Pearl River Delta Region].

PubMed

Yin, Sha-sha; Zheng, Jun-yu; Zhang, Li-jun; Zhong, Liu-ju

2010-05-01

Based on the collected activity data and emission factors of anthropogenic ammonia sources, a 2006-based anthropogenic ammonia emission inventory was developed for the Pearl River Delta (PRD) region by source categories and cities with the use of appropriate estimation methods. The results show: (1) the total NH3 emission from anthropogenic sources in the PRD region was 194. 8 kt; (2) the agriculture sources were major contributors of anthropogenic ammonia sources, in which livestock sources shared 62.1% of total NH3 emission and the contribution of application of nitrogen fertilizers was 21.7%; (3) the broiler was the largest contributor among the livestock sources, accounting for 43.4% of the livestock emissions, followed by the hog with a contribution of 32.1%; (4) Guangzhou was the largest ammonia emission city in the PRD region, and then Jiangmen, accounting for 23.4% and 19.1% of total NH3 emission in the PRD region respectively, with major sources as livestock sources and application of nitrogen fertilizers.

Focal mechanism of the seismic series prior to the 2011 El Hierro eruption

NASA Astrophysics Data System (ADS)

del Fresno, C.; Buforn, E.; Cesca, S.; Domínguez Cerdeña, I.

2015-12-01

The onset of the submarine eruption of El Hierro (10-Oct-2011) was preceded by three months of low-magnitude seismicity (Mw<4.0) characterized by a well documented hypocenter migration from the center to the south of the island. Seismic sources of this series have been studied in order to understand the physical process of magma migration. Different methodologies were used to obtain focal mechanisms of largest shocks. Firstly, we have estimated the joint fault plane solutions for 727 shocks using first motion P polarities to infer the stress pattern of the sequence and to determine the time evolution of principle axes orientation. Results show almost vertical T-axes during the first two months of the series and horizontal P-axes on N-S direction coinciding with the migration. Secondly, a point source MT inversion was performed with data of the largest 21 earthquakes of the series (M>3.5). Amplitude spectra was fitted at local distances (<20km). Reliability and stability of the results were evaluated with synthetic data. Results show a change in the focal mechanism pattern within the first days of October, varying from complex sources of higher non-double-couple components before that date to a simpler strike-slip mechanism with horizontal tension axes on E-W direction the week prior to the eruption onset. A detailed study was carried out for the 8 October 2011 earthquake (Mw=4.0). Focal mechanism was retrieved using a MT inversion at regional and local distances. Results indicate an important component of strike-slip fault and null isotropic component. The stress pattern obtained corresponds to horizontal compression in a NNW-SSE direction, parallel to the southern ridge of the island, and a quasi-horizontal extension in an EW direction. Finally, a simple source time function of 0.3s has been estimated for this shock using the Empirical Green function methodology.

Water resources of the Batavia Kill basin at Windham, Greene County, New York

USGS Publications Warehouse

Heisig, Paul M.

1999-01-01

The water resources of a 27.6-square-mile section of the Batavia Kill Basin near the village of Windham, N.Y., which has undergone substantial development, were evaluated. The evaluation entailed (1) estimation of the magnitude and distribution of several hydrologic components, including recharge, (2) measurement of discharge and chemical quality of the Batavia Kill and selected tributaries, (3) analysis of ground-water flow and chemistry, and (4) a conceptualization of the ground-water flow system.The region consists of deeply dissected, relatively flat-lying, clastic sedimentary sequences variably overlain by as much as 120 feet of glacial deposits. The types of bedrock fractures and their distribution in the Batavia Kill valley are consistent with valley stress-relief characteristics. Till predominates in the uplands, and stratified drift typically dominates within the valley of the Batavia Kill and the lower section of its largest tributary valley (Mitchell Hollow).Fractured bedrock is the most commonly used water source within the study area. The areas of highest yielding bedrock generally are with valleys, where the shallow fractures are saturated. Stratified-drift aquifers are also limited to the largest valleys; the greatest saturated thicknesses are in the Batavia Kill valley at Windham. A conceptual model of ground-water flow within the study areas suggests that the zones of most active flow are shallow fractured bedrock in upland areas and the shallow stratified drift in the largest valleys.The hydrogeologic system has been altered by development; major effects include (1) chemical alteration of natural ground-water and surface-water quality by point- and nonpoint-source contaminants, (2) hydraulic interconnection of other-wise isolated bedrock fractures by wellbores, and (3) drawdowns in wells within the Batavia Kill valley by pumping from the bedrock aquifer. Water resource development of the most promising unconsolidated aquifer beneath Windham may be precluded by the potential for contamination by leachate from an abandoned landfill, road-salt stockpiles, and domestic septic systems in the area.

Suspended Sediment Loads and Tributary Inputs in the Mississippi River below St. Louis, MO, 1990-2013 Compared With Earlier Results

NASA Astrophysics Data System (ADS)

Allison, M. A.; Biedenharn, D. S.; Dahl, T. A.; Kleiss, B.; Little, C. D.

2017-12-01

Annual suspended sediment loads and water discharges were calculated in the Mississippi River mainstem channel, and at the most downstream gaging station for major tributaries, from below the Missouri confluence near St. Louis, MO to Belle Chasse, LA, as well as down the Atchafalaya distributary for water years 1990 to 2013. The purpose of the present study was to assess changes in the Mississippi River sediment budget over the past half century, and to examine the continuing role that anthropogenic (e.g., dams, river control works, soil conservation practices) and natural (e.g., rainfall and denudation rates) factors have in controlling these changes. Sixteen of the 17 measured Mississippi River tributaries decreased in total suspended sediment load) from 1970-1978 to 1990-2013. The largest decreases occurred in the 2nd (Ohio River, 41% of 1970-1978) and 4th (Arkansas River, 45% of 1970-1978) largest water sources to the Mississippi. The Missouri River remains the largest Mississippi River tributary in terms of average annual suspended sediment flux; its relative contribution increased from 38% to 51% of the total flux from the 17 measured tributaries, even as its total suspended flux declined by 13%. Averaged over the period of study (WY 1990-2013), water flux increased by 468% and sediment flux increased by 37,418% downstream from the Gavin's Point Dam to the confluence with the Mississippi. Possible reasons for this disproportional increase in suspended sediment load downstream include sediment-rich contributions from 2nd order rivers below the dams and channel incision. Suggested station improvements to the system include improved monitoring of the Upper Mississippi and Arkansas River tributaries, establishing additional mainstem stations in the reach between Thebes, IL and Arkansas City, AR, and standardization of laboratory and field methodologies to eliminate a major source of station-to-station and time-series variability in the sediment budgeting.

To Grid or Not to Grid… Precipitation Data and Hydrological Modeling in the Khangai Mountain Region of Mongolia

NASA Astrophysics Data System (ADS)

Venable, N. B. H.; Fassnacht, S. R.; Adyabadam, G.

2014-12-01

Precipitation data in semi-arid and mountainous regions is often spatially and temporally sparse, yet it is a key variable needed to drive hydrological models. Gridded precipitation datasets provide a spatially and temporally coherent alternative to the use of point-based station data, but in the case of Mongolia, may not be constructed from all data available from government data sources, or may only be available at coarse resolutions. To examine the uncertainty associated with the use of gridded and/or point precipitation data, monthly water balance models of three river basins across forest steppe (the Khoid Tamir River at Ikhtamir), steppe (the Baidrag River at Bayanburd), and desert steppe (the Tuin River at Bogd) ecozones in the Khangai Mountain Region of Mongolia were compared. The models were forced over a 10-year period from 2001-2010, with gridded temperature and precipitation data at a 0.5 x 0.5 degree resolution. These results were compared to modeling using an interpolated hybrid of the gridded data and additional point data recently gathered from government sources; and with point data from the nearest meteorological station to the streamflow gage of choice. Goodness-of-fit measures including the Nash-Sutcliff Efficiency statistic, the percent bias, and the RMSE-observations standard deviation ratio were used to assess model performance. The results were mixed with smaller differences between the two gridded products as compared to the differences between gridded products and station data. The largest differences in precipitation inputs and modeled runoff amounts occurred between the two gridded datasets and station data in the desert steppe (Tuin), and the smallest differences occurred in the forest steppe (Khoid Tamir) and steppe (Baidrag). Mean differences between water balance model results are generally smaller than mean differences in the initial input data over the period of record. Seasonally, larger differences in gridded versus station-based precipitation products and modeled outputs occur in summer in the desert-steppe, and in spring in the forest steppe. Choice of precipitation data source in terms of gridded or point-based data directly affects model outcomes with greater uncertainty noted on a seasonal basis across ecozones of the Khangai.

An overview of particulate emissions from residential biomass combustion

NASA Astrophysics Data System (ADS)

Vicente, E. D.; Alves, C. A.

2018-01-01

Residential biomass burning has been pointed out as one of the largest sources of fine particles in the global troposphere with serious impacts on air quality, climate and human health. Quantitative estimations of the contribution of this source to the atmospheric particulate matter levels are hard to obtain, because emission factors vary greatly with wood type, combustion equipment and operating conditions. Updated information should improve not only regional and global biomass burning emission inventories, but also the input for atmospheric models. In this work, an extensive tabulation of particulate matter emission factors obtained worldwide is presented and critically evaluated. Existing quantifications and the suitability of specific organic markers to assign the input of residential biomass combustion to the ambient carbonaceous aerosol are also discussed. Based on these organic markers or other tracers, estimates of the contribution of this sector to observed particulate levels by receptor models for different regions around the world are compiled. Key areas requiring future research are highlighted and briefly discussed.

Evolution of air pollution source contributions over one decade, derived by PM10 and PM2.5 source apportionment in two metropolitan urban areas in Greece

NASA Astrophysics Data System (ADS)

Diapouli, E.; Manousakas, M.; Vratolis, S.; Vasilatou, V.; Maggos, Th; Saraga, D.; Grigoratos, Th; Argyropoulos, G.; Voutsa, D.; Samara, C.; Eleftheriadis, K.

2017-09-01

Metropolitan Urban areas in Greece have been known to suffer from poor air quality, due to variety of emission sources, topography and climatic conditions favouring the accumulation of pollution. While a number of control measures have been implemented since the 1990s, resulting in reductions of atmospheric pollution and changes in emission source contributions, the financial crisis which started in 2009 has significantly altered this picture. The present study is the first effort to assess the contribution of emission sources to PM10 and PM2.5 concentration levels and their long-term variability (over 5-10 years), in the two largest metropolitan urban areas in Greece (Athens and Thessaloniki). Intensive measurement campaigns were conducted during 2011-2012 at suburban, urban background and urban traffic sites in these two cities. In addition, available datasets from previous measurements in Athens and Thessaloniki were used in order to assess the long-term variability of concentrations and sources. Chemical composition analysis of the 2011-2012 samples showed that carbonaceous matter was the most abundant component for both PM size fractions. Significant increase of carbonaceous particle concentrations and of OC/EC ratio during the cold period, especially in the residential urban background sites, pointed towards domestic heating and more particularly wood (biomass) burning as a significant source. PMF analysis further supported this finding. Biomass burning was the largest contributing source at the two urban background sites (with mean contributions for the two size fractions in the range of 24-46%). Secondary aerosol formation (sulphate, nitrate & organics) was also a major contributing source for both size fractions at the suburban and urban background sites. At the urban traffic site, vehicular traffic (exhaust and non-exhaust emissions) was the source with the highest contributions, accounting for 44% of PM10 and 37% of PM2.5, respectively. The long-term variability of emission sources in the two cities (over 5-10 years), assessed through a harmonized application of the PMF technique on recent and past year data, clearly demonstrates the effective reduction in emissions during the last decade due to control measures and technological development; however, it also reflects the effects of the financial crisis in Greece during these years, which has led to decreased economic activities and the adoption of more polluting practices by the local population in an effort to reduce living costs.

Contribution of PAHs from coal-tar pavement sealcoat and other sources to 40 U.S. lakes

USGS Publications Warehouse

Van Metre, Peter C.; Mahler, Barbara J.

2010-01-01

Contamination of urban lakes and streams by polycyclic aromatic hydrocarbons (PAHs) has increased in the United States during the past 40 years. We evaluated sources of PAHs in post-1990 sediments in cores from 40 lakes in urban areas across the United States using a contaminant mass-balance receptor model and including as a potential source coal-tar-based (CT) sealcoat, a recently recognized source of urban PAH. Other PAH sources considered included several coal- and vehicle-related sources, wood combustion, and fuel-oil combustion. The four best modeling scenarios all indicate CT sealcoat is the largest PAH source when averaged across all 40 lakes, contributing about one-half of PAH in sediment, followed by vehicle-related sources and coal combustion. PAH concentrations in the lakes were highly correlated with PAH loading from CT sealcoat (Spearman's rho=0.98), and the mean proportional PAH profile for the 40 lakes was highly correlated with the PAH profile for dust from CT-sealed pavement (r=0.95). PAH concentrations and mass and fractional loading from CT sealcoat were significantly greater in the central and eastern United States than in the western United States, reflecting regional differences in use of different sealcoat product types. The model was used to calculate temporal trends in PAH source contributions during the last 40 to 100 years to eight of the 40 lakes. In seven of the lakes, CT sealcoat has been the largest source of PAHs since the 1960s, and in six of those lakes PAH trends are upward. Traffic is the largest source to the eighth lake, located in southern California where use of CT sealcoat is rare.

Organic Matter Remineralization Predominates Phosphorus Cycling in the Mid-Bay Sediments in the Chesapeake Bay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sunendra, Joshi R.; Kukkadapu, Ravi K.; Burdige, David J.

2015-05-19

The Chesapeake Bay, the largest and most productive estuary in the US, suffers from varying degrees of water quality issues fueled by both point and non–point source nutrient sources. Restoration of the bay is complicated by the multitude of nutrient sources, their variable inputs and hydrological conditions, and complex interacting factors including climate forcing. These complexities not only restrict formulation of effective restoration plans but also open up debates on accountability issues with nutrient loading. A detailed understanding of sediment phosphorus (P) dynamics enables one to identify the exchange of dissolved constituents across the sediment- water interface and aid tomore » better constrain mechanisms and processes controlling the coupling between the sediments and the overlying waters. Here we used phosphate oxygen isotope ratios (δ18Op) in concert with sediment chemistry, XRD, and Mössbauer spectroscopy on the sediment retrieved from an organic rich, sulfidic site in the meso-haline portion of the mid-bay to identify sources and pathway of sedimentary P cycling and to infer potential feedback effect on bottom water hypoxia and surface water eutrophication. Isotope data indicate that the regeneration of inorganic P from organic matter degradation (remineralization) is the predominant, if not sole, pathway for authigenic P precipitation in the mid-bay sediments. We interpret that the excess inorganic P generated by remineralization should have overwhelmed any bottom-water and/or pore-water P derived from other sources or biogeochemical processes and exceeded saturation with respect to authigenic P precipitation. It is the first research that identifies the predominance of remineralization pathway against remobilization (coupled Fe-P cycling) pathway in the Chesapeake Bay. Therefore, these results are expected to have significant implications for the current understanding of P cycling and benthic-pelagic coupling in the bay, particularly on the source and pathway of P that sustains hypoxia and supports phytoplankton growth in the surface water.« less

Clay-mineral suites, sources, and inferred dispersal routes: Southern California continental shelf

USGS Publications Warehouse

Hein, J.R.; Dowling, J.S.; Schuetze, A.; Lee, H.J.

2003-01-01

Clay mineralogy is useful in determining the distribution, sources, and dispersal routes of fine-grained sediments. In addition, clay minerals, especially smectite, may control the degree to which contaminants are adsorbed by the sediment. We analyzed 250 shelf sediment samples, 24 river-suspended-sediment samples, and 12 river-bed samples for clay-mineral contents in the Southern California Borderland from Point Conception to the Mexico border. In addition, six samples were analyzed from the Palos Verdes Headland in order to characterize the clay minerals contributed to the offshore from that point source. The <2 ??m-size fraction was isolated, Mg-saturated, and glycolated before analysis by X-ray diffraction. Semi-quantitative percentages of smectite, illite, and kaolinite plus chlorite were calculated using peak areas and standard weighting factors. Most fine-grained sediment is supplied to the shelf by rivers during major winter storms, especially during El Nin??o years. The largest sediment fluxes to the region are from the Santa Ynez and Santa Clara Rivers, which drain the Transverse Ranges. The mean clay-mineral suite for the entire shelf sediment data set (26% smectite, 50% illite, 24% kaolinite+chlorite) is closely comparable to that for the mean of all the rivers (31% smectite, 49% illite, 20% kaolinite+chlorite), indicating that the main source of shelf fine-grained sediments is the adjacent rivers. However, regional variations do exist and the shelf is divided into four provinces with characteristic clay-mineral suites. The means of the clay-mineral suites of the two southernmost provinces are within analytical error of the mineral suites of adjacent rivers. The next province to the north includes Santa Monica Bay and has a suite of clay minerals derived from mixing of fine-grained sediments from several sources, both from the north and south. The northernmost province clay-mineral suite matches moderately well that of the adjacent rivers, but does indicate some mixing from sources in adjacent provinces.

Public funding for contraceptive, sterilization and abortion services, 1994.

PubMed

Sollom, T; Gold, R B; Saul, R

1996-01-01

In 1994, federal and state funding for contraceptive services and supplies reached +715 million. Funding totaled +148 million for contraceptive sterilization and +90 million for abortion services. According to a survey of state health, Medicaid and social service agencies, reported spending on contraceptive services and supplies increased by 11% between 1992 and 1994. In the same period, spending under Title X rose by 37%, making it the third largest public funding source for contraceptive services and supplies. The largest source of public funds for family planning services continues to be the joint federal-state Medicaid program. Medicaid family planning expenditures increased by only 4% between 1992 and 1994, a sizable decrease in growth from previous years. State funds continue to be the second largest source, providing almost one-quarter of reported public expenditures in 1994. The maternal and child health and social services block grants remain relatively minor sources of support nationally, although in a handful of states they provide the majority of public-sector funds. State governments were virtually the sole source of public support for the 203,200 abortions provided in 1994 to low-income women. Despite the loosening of federal abortion funding criteria in FY 1994 permitting payment in cases of rape and incest, federally funded abortions numbered only 282.

Observations and Measurements of Dust Transport from the Patagonia Desert into the South Atlantic Ocean in 2004 and 2005

NASA Astrophysics Data System (ADS)

Gasso, S.; Gaiero, D. M.; Villoslada, B.; Liske, E.

2005-12-01

The largest continental landmass south of the 40-degree parallel and potentially one of the largest sources of dust into the Southern Ocean (SO) is the Patagonia desert. Most of the estimates of dust outflow and deposition from this region into the South Atlantic Ocean are based on model simulations. However, there are very few measurements available that can corroborate these estimates. Satellite assessments of dust activity offer conflicting views. For example, monthly time series of satellite-derived (e.g. AVHRR and MODIS) aerosol optical depth (AOD) indicate that dust activity is minimal. However, a study with the TOMS Aerosol Index (Prospero et al., 2002) showed that the frequency of dust events is in the range of 7-14 days/month during the years 1978 through 1993. In addition, surface visibility observations along the Patagonian coast confirm that ocean-going dust events do occur during the summer and spring months. These discrepancies indicate fundamental uncertainties regarding the frequency and extent of dust activity in Patagonia. Given that the SO is the largest high-chlorophyll, low-nutrient area in the world and that the flux of nutrient-rich dust has the potential to modify biological activity with possible climatic consequences, it is of interest to have a better understanding of how often and intense are dust events in the Patagonia region. We surveyed the reports of dust activity from surface weather stations in the Patagonia region during the period June, 2004 to April, 2005. These observations were compared with simultaneous MODIS true color pictures and the corresponding aerosol retrievals. In addition, measurements of vertical and horizontal dust flux were collected by dust samplers at four sites along the coast. The horizontal flux measurements were compared with the same estimates derived from MODIS. According to the true color pictures and confirmed by the surface visibility observations, we recorded at least 16 ocean-going dust events. The scale of the events varied from small (single dust plumes along the coast) to large (dust front extending ~600 km). Most of the large events occurred during the late summer. Due to the presence of sun glint, cloud obstruction, or coastal sediments, the MODIS automatic aerosol algorithm did not derive AODs in many instances and, as result, many events were not recorded in the MODIS monthly database. Dust sources are numerous and dust plumes outflow at any place along the coastline (> 1000 km) including some very active sources as far south as in the Tierra del Fuego Island (54S). The main sources identified are coastal saltbeds, inland deflation hollows and receding shores of large lakes. Although some of major emitting points have been included as sources in dust models, there are some notable exceptions, for example most of the coastal sources. We note, in addition, that the scale and diversity of the different sources pose significant challenges with respect to parameterization in global models of dust dispersion.

Life cycle assessment of cellulosic and advanced biofuel crops

USDA-ARS?s Scientific Manuscript database

Estimating the carbon intensity of biofuel production is important in order to meet greenhouse gas (GHG) targets set by government policy. Nitrous oxide emissions are the largest source and soil carbon the largest sink of GHGs for determining the carbon intensity of biofuels during their production ...

Infrasound radiated by the Gerdec and Chelopechene explosions: propagation along unexpected paths

NASA Astrophysics Data System (ADS)

Green, David N.; Vergoz, Julien; Gibson, Robert; Le Pichon, Alexis; Ceranna, Lars

2011-05-01

Infrasound propagation paths through the atmosphere are controlled by the temporally and spatially varying sound speed and wind speed amplitudes. Because of the complexity of atmospheric acoustic propagation it is often difficult to reconcile observed infrasonic arrivals with the sound speed profiles predicted by meteorological specifications. This paper provides analyses of unexpected arrivals recorded in Europe and north Africa from two series of accidental munitions dump explosions, recorded at ranges greater than 1000 km: two explosions at Gerdec, Albania, on 2008 March 15 and four explosions at Chelopechene, Bulgaria, on 2008 July 3. The recorded signal characteristics include multiple pulsed arrivals, celerities between 0.24 and 0.34 km s-1 and some signal frequency content above 1 Hz. Often such characteristics are associated with waves that have propagated within a ground-to-stratosphere waveguide, although the observed celerities extend both above and below the conventional range for stratospheric arrivals. However, state-of-the-art meteorological specifications indicate that either weak, or no, ground-to-stratosphere waveguides are present along the source-to-receiver paths. By incorporating realistic gravity-wave induced horizontal velocity fluctuations into time-domain Parabolic Equation models the pulsed nature of the signals is simulated, and arrival times are predicted to within 30 s of the observed values (<1 per cent of the source-to-receiver transit time). Modelling amplitudes is highly dependent upon estimates of the unknown acoustic source strength (or equivalent chemical explosive yield). Current empirical explosive yield relationships, derived from infrasonic amplitude measurements from point-source chemical explosions, suggest that the equivalent chemical yield of the largest Gerdec explosion was of the order of 1 kt and the largest Chelopechene explosion was of the order of 100 t. When incorporating these assumed yields, the Parabolic Equation simulations predict peak signal amplitudes to within an order of magnitude of the observed values. As gravity wave velocity perturbations can significantly influence both infrasonic arrival times and signal amplitudes they need to be accounted for in source location and yield estimation routines, both of which are important for explosion monitoring, especially in the context of the Comprehensive Nuclear-Test-Ban Treaty.

Using E-PRTR data on point source emissions to air and water—First steps towards a national chemical footprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sörme, L., E-mail: louise.sorme@scb.se; Palm, V.; KTH Royal Institute of Technology, Division of Environmental Strategies Research, SE-100 44 Stockholm

2016-01-15

There is a great need for indicators to monitor the use and potential impacts of hazardous chemicals. Today there is a huge lack of data, methods and results and method development and studies should be given urgent priority. The aim of this paper was to develop and test an approach to calculate the potential environmental impacts of chemicals for a whole country using the E-PRTR (European Pollutant Release and Transfer Register) as a database and Sweden as an example. Swedish data from 2008 on emissions to air and water for 54 substances from point sources were retrieved from an openmore » database. The data were transformed and aggregated using USEtox, a life-cycle impact assessment (LCIA) method for calculating potential human toxicity and ecotoxicity, both from industrial emissions directly and after input–output analysis (IO analysis) to reallocate emissions to product categories. Zinc to air and water contributed most to human toxicity followed by mercury to air. The largest contribution by industry to potential human toxicity came from the metal industry, followed by the paper and paper product industry. For potential ecotoxicity, zinc, fluoranthene and copper contributed the most. The largest contributions by industry came from the paper and paper products manufacturing sector, followed by the basic metals manufacturing sector. The approach used here can be seen as the first step towards a chemical footprint for nations. By adding data from other countries and other sources, a more complete picture can be gained in line with other footprint calculations. Furthermore, diffuse emissions from, for example, transport or emissions of pesticides could also be added for a more holistic assessment. Since the area of chemicals is complicated, it is probably necessary to develop and use several indicators that complement each other. It is suggested that the approach outlined here could be useful in developing a method for establishing a national chemical footprint. - Highlights: • European Pollutant and Transfer Register (E-PRTR) used to develop indicators • Study combined emissions to air and water from E-PRTR with USEtox and IO analysis • Metals and especially zinc contributed most to potential human toxicity and ecotoxicity • Paper and metal industries contribute most to potential human toxicity and ecotoxicity • This new assessment could be used by many countries and can be developed further.« less

VizieR Online Data Catalog: Water masers in M31. I. Recombination lines (Darling+, 2016)

NASA Astrophysics Data System (ADS)

Darling, J.; Gerard, B.; Amiri, N.; Lawrence, K.

2016-09-01

We constructed a catalog of 506 unresolved 24um sources from the Spitzer 24um map of M31 (Gordon et al. 2006ApJ...638L..87G); see Figure 1. Darling (2011ApJ...732L...2D) observed 206 24um sources in M31 using the Green Bank Telescope (GBT) in 2010 October through December. The 616-523 22.23508GHz ortho-water maser line observations were reported in Darling (2011ApJ...732L...2D), but simultaneous observations of the para-ammonia (NH3) rotational ground-state inversion transitions in the metastable states (J,K)=(1,1) and (2,2) at 23.6945 and 23.72263GHz, respectively, and the hydrogen recombination line H66α at 22.36417GHz were not. We subsequently observed all four of these lines toward an additional 300 24um sources in 2011 October through 2012 January. The resolution of the 24um Spitzer image is 6" (Gordon et al. 2006ApJ...638L..87G), so the unresolved IR sources remained within the 33" GBT beam even during the largest pointing drifts. The 33" beam (FWHM) at 22GHz spans 125pc in M31. (1 data file).

Polarized point sources in the LOFAR Two-meter Sky Survey: A preliminary catalog

NASA Astrophysics Data System (ADS)

Van Eck, C. L.; Haverkorn, M.; Alves, M. I. R.; Beck, R.; Best, P.; Carretti, E.; Chyży, K. T.; Farnes, J. S.; Ferrière, K.; Hardcastle, M. J.; Heald, G.; Horellou, C.; Iacobelli, M.; Jelić, V.; Mulcahy, D. D.; O'Sullivan, S. P.; Polderman, I. M.; Reich, W.; Riseley, C. J.; Röttgering, H.; Schnitzeler, D. H. F. M.; Shimwell, T. W.; Vacca, V.; Vink, J.; White, G. J.

2018-06-01

The polarization properties of radio sources at very low frequencies (<200 MHz) have not been widely measured, but the new generation of low-frequency radio telescopes, including the Low Frequency Array (LOFAR: a Square Kilometre Array Low pathfinder), now gives us the opportunity to investigate these properties. In this paper, we report on the preliminary development of a data reduction pipeline to carry out polarization processing and Faraday tomography for data from the LOFAR Two-meter Sky Survey (LOTSS) and present the results of this pipeline from the LOTSS preliminary data release region (10h45m-15h30m right ascension, 45°-57° declination, 570 square degrees). We have produced a catalog of 92 polarized radio sources at 150 MHz at 4.'3 resolution and 1 mJy rms sensitivity, which is the largest catalog of polarized sources at such low frequencies. We estimate a lower limit to the polarized source surface density at 150 MHz, with our resolution and sensitivity, of 1 source per 6.2 square degrees. We find that our Faraday depth measurements are in agreement with previous measurements and have significantly smaller errors. Most of our sources show significant depolarization compared to 1.4 GHz, but there is a small population of sources with low depolarization indicating that their polarized emission is highly localized in Faraday depth. We predict that an extension of this work to the full LOTSS data would detect at least 3400 polarized sources using the same methods, and probably considerably more with improved data processing.

China’s Economic Conditions

DTIC Science & Technology

2009-12-11

5 Measuring the Size of China’s Economy .....................................................................................6...29 Table A-4. China’s Top Five African Export Markets : 2004-2008 .............................................. 30 Table A-5...partner, its third largest export market , and its largest source of imports. Many U.S. companies have extensive operations in China in order to sell

Development of a stationary carbon emission inventory for Shanghai using pollution source census data

NASA Astrophysics Data System (ADS)

Li, Xianzhe; Jiang, Ping; Zhang, Yan; Ma, Weichun

2016-12-01

This study utilizes 521,631 activity data points from the 2007 Shanghai Pollution Source Census to compile a stationary carbon emission inventory for Shanghai. The inventory generated from our dataset shows that a large portion of Shanghai's total energy use consists of coal-oriented energy consumption. The electricity and heat production industries, iron and steel mills, and the petroleum refining industry are the main carbon emitters. In addition, most of these industries are located in Baoshan District, which is Shanghai's largest contributor of carbon emissions. Policy makers can use the enterpriselevel carbon emission inventory and the method designed in this study to construct sound carbon emission reduction policies. The carbon trading scheme to be established in Shanghai based on the developed carbon inventory is also introduced in this paper with the aim of promoting the monitoring, reporting and verification of carbon trading. Moreover, we believe that it might be useful to consider the participation of industries, such as those for food processing, beverage, and tobacco, in Shanghai's carbon trading scheme. Based on the results contained herein, we recommend establishing a comprehensive carbon emission inventory by inputting data from the pollution source census used in this study.

Nitrogen Loading in Jamaica Bay, Long Island, New York: Predevelopment to 2005

USGS Publications Warehouse

Benotti, Mark J.; Abbene, Irene; Terracciano, Stephen A.

2007-01-01

Nitrogen loading to Jamaica Bay, a highly urbanized estuary on the southern shore of western Long Island, New York, has increased from an estimated rate of 35.6 kilograms per day (kg/d) under predevelopment conditions (pre-1900), chiefly as nitrate plus nitrite from ground-water inflow, to an estimated 15,800 kilograms per day as total nitrogen in 2005. The principal point sources are wastewater-treatment plants, combined sewer overflow/stormwater discharge during heavy precipitation, and subway dewatering, which account for 92 percent of the current (2005) nitrogen load. The principal nonpoint sources are landfill leachate, ground-water flow, and atmospheric deposition, which account for 8 percent of the current nitrogen load. The largest single source of nitrogen to Jamaica Bay is wastewater-treatment plants, which account for 89 percent of the nitrogen load. The current and historic contributions of nitrogen from seawater are unknown, although at present, the ocean likely serves as a sink for nitrogen from Jamaica Bay. Currently, concentrations of nitrogen in surface water are high throughout Jamaica Bay, but some areas with relatively little mixing have concentrations that are five times higher than areas that are well mixed.

A method for separation of heavy metal sources in urban groundwater using multiple lines of evidence.

PubMed

Hepburn, Emily; Northway, Anne; Bekele, Dawit; Liu, Gang-Jun; Currell, Matthew

2018-06-11

Determining sources of heavy metals in soils, sediments and groundwater is important for understanding their fate and transport and mitigating human and environmental exposures. Artificially imported fill, natural sediments and groundwater from 240 ha of reclaimed land at Fishermans Bend in Australia, were analysed for heavy metals and other parameters to determine the relative contributions from different possible sources. Fishermans Bend is Australia's largest urban re-development project, however, complicated land-use history, geology, and multiple contamination sources pose challenges to successful re-development. We developed a method for heavy metal source separation in groundwater using statistical categorisation of the data, analysis of soil leaching values and fill/sediment XRF profiling. The method identified two major sources of heavy metals in groundwater: 1. Point sources from local or up-gradient groundwater contaminated by industrial activities and/or legacy landfills; and 2. contaminated fill, where leaching of Cu, Mn, Pb and Zn was observed. Across the precinct, metals were most commonly sourced from a combination of these sources; however, eight locations indicated at least one metal sourced solely from fill leaching, and 23 locations indicated at least one metal sourced solely from impacted groundwater. Concentrations of heavy metals in groundwater ranged from 0.0001 to 0.003 mg/L (Cd), 0.001-0.1 mg/L (Cr), 0.001-0.2 mg/L (Cu), 0.001-0.5 mg/L (Ni), 0.001-0.01 mg/L (Pb), and 0.005-1.2 mg/L (Zn). Our method can determine the likely contribution of different metal sources to groundwater, helping inform more detailed contamination assessments and precinct-wide management and remediation strategies. Copyright © 2018 Elsevier Ltd. All rights reserved.

One-loop effective actions and higher spins. Part II

NASA Astrophysics Data System (ADS)

Bonora, L.; Cvitan, M.; Prester, P. Dominis; Giaccari, S.; Štemberga, T.

2018-01-01

In this paper we continue and improve the analysis of the effective actions obtained by integrating out a scalar and a fermion field coupled to external symmetric sources, started in the previous paper. The first subject we study is the geometrization of the results obtained there, that is we express them in terms of covariant Jacobi tensors. The second subject concerns the treatment of tadpoles and seagull terms in order to implement off-shell covariance in the initial model. The last and by far largest part of the paper is a repository of results concerning all two point correlators (including mixed ones) of symmetric currents of any spin up to 5 and in any dimensions between 3 and 6. In the massless case we also provide formulas for any spin in any dimension.

Black carbon emissions from Russian diesel sources. Case study of Murmansk

DOE PAGES

Evans, M.; Kholod, N.; Malyshev, V.; ...

2015-07-27

Black carbon (BC) is a potent pollutant because of its effects on climate change, ecosystems and human health. Black carbon has a particularly pronounced impact as a climate forcer in the Arctic because of its effect on snow albedo and cloud formation. We have estimated BC emissions from diesel sources in the Murmansk Region and Murmansk City, the largest city in the world above the Arctic Circle. In this study we developed a detailed inventory of diesel sources including on-road vehicles, off-road transport (mining, locomotives, construction and agriculture), ships and diesel generators. For on-road transport, we conducted several surveys tomore » understand the vehicle fleet and driving patterns, and, for all sources, we also relied on publicly available local data sets and analysis. We calculated that BC emissions in the Murmansk Region were 0.40 Gg in 2012. The mining industry is the largest source of BC emissions in the region, emitting 69 % of all BC emissions because of its large diesel consumption and absence of emissions controls. On-road vehicles are the second largest source, emitting about 13 % of emissions. Old heavy duty trucks are the major source of emissions. Emission controls on new vehicles limit total emissions from on-road transportation. Vehicle traffic and fleet surveys show that many of the older cars on the registry are lightly or never used. We also estimated that total BC emissions from diesel sources in Russia were 50.8 Gg in 2010, and on-road transport contributed 49 % of diesel BC emissions. Agricultural machinery is also a significant source Russia-wide, in part because of the lack of controls on off-road vehicles.« less

Black carbon emissions from Russian diesel sources. Case study of Murmansk

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, M.; Kholod, N.; Malyshev, V.

Black carbon (BC) is a potent pollutant because of its effects on climate change, ecosystems and human health. Black carbon has a particularly pronounced impact as a climate forcer in the Arctic because of its effect on snow albedo and cloud formation. We have estimated BC emissions from diesel sources in the Murmansk Region and Murmansk City, the largest city in the world above the Arctic Circle. In this study we developed a detailed inventory of diesel sources including on-road vehicles, off-road transport (mining, locomotives, construction and agriculture), ships and diesel generators. For on-road transport, we conducted several surveys tomore » understand the vehicle fleet and driving patterns, and, for all sources, we also relied on publicly available local data sets and analysis. We calculated that BC emissions in the Murmansk Region were 0.40 Gg in 2012. The mining industry is the largest source of BC emissions in the region, emitting 69 % of all BC emissions because of its large diesel consumption and absence of emissions controls. On-road vehicles are the second largest source, emitting about 13 % of emissions. Old heavy duty trucks are the major source of emissions. Emission controls on new vehicles limit total emissions from on-road transportation. Vehicle traffic and fleet surveys show that many of the older cars on the registry are lightly or never used. We also estimated that total BC emissions from diesel sources in Russia were 50.8 Gg in 2010, and on-road transport contributed 49 % of diesel BC emissions. Agricultural machinery is also a significant source Russia-wide, in part because of the lack of controls on off-road vehicles.« less

NO x emissions from large point sources: variability in ozone production, resulting health damages and economic costs

NASA Astrophysics Data System (ADS)

Mauzerall, Denise L.; Sultan, Babar; Kim, Namsoug; Bradford, David F.

We present a proof-of-concept analysis of the measurement of the health damage of ozone (O 3) produced from nitrogen oxides (NO=NO+NO) emitted by individual large point sources in the eastern United States. We use a regional atmospheric model of the eastern United States, the Comprehensive Air quality Model with Extensions (CAMx), to quantify the variable impact that a fixed quantity of NO x emitted from individual sources can have on the downwind concentration of surface O 3, depending on temperature and local biogenic hydrocarbon emissions. We also examine the dependence of resulting O 3-related health damages on the size of the exposed population. The investigation is relevant to the increasingly widely used "cap and trade" approach to NO x regulation, which presumes that shifts of emissions over time and space, holding the total fixed over the course of the summer O 3 season, will have minimal effect on the environmental outcome. By contrast, we show that a shift of a unit of NO x emissions from one place or time to another could result in large changes in resulting health effects due to O 3 formation and exposure. We indicate how the type of modeling carried out here might be used to attach externality-correcting prices to emissions. Charging emitters fees that are commensurate with the damage caused by their NO x emissions would create an incentive for emitters to reduce emissions at times and in locations where they cause the largest damage.

Estimated withdrawals and use of freshwater in Vermont, 1990

USGS Publications Warehouse

Horn, M.A.; Medalie, Laura

1996-01-01

Estimated freshwater withdrawals during 1990 in Vermont totaled about 632 million gallons per day. The largest withdrawals were for thermoelectric- power generation (82 percent), industrial use (7 percent), and public supply (6 percent). Most withdrawals, 587 million gallons per day, were made from surface-water sources as compared to 44.9 million gallons per day from ground-water sources. The largest withdrawals were in the Upper Connecticut-Mascomo River Basin (525 million gallons per day). About 17,700 million gallons per day were used instream for hydroelectric-poser generation, the largest of which were in the Upper Connecticut-Mascoma and Otter River Basins. Other information describing water-use patters is shown in tables, bar graphs, pie charts, maps, and accompanying text. The data are aggregated by river basin (hydrologic cataloging unit), and all amounts are reports in million gallons per day.

Prediction of phosphorus loads in an artificially drained lowland catchment using a modified SWAT model

NASA Astrophysics Data System (ADS)

Bauwe, Andreas; Eckhardt, Kai-Uwe; Lennartz, Bernd

2017-04-01

Eutrophication is still one of the main environmental problems in the Baltic Sea. Currently, agricultural diffuse sources constitute the major portion of phosphorus (P) fluxes to the Baltic Sea and have to be reduced to achieve the HELCOM targets and improve the ecological status. Eco-hydrological models are suitable tools to identify sources of nutrients and possible measures aiming at reducing nutrient loads into surface waters. In this study, the Soil and Water Assessment Tool (SWAT) was applied to the Warnow river basin (3300 km2), the second largest watershed in Germany discharging into the Baltic Sea. The Warnow river basin is located in northeastern Germany and characterized by lowlands with a high proportion of artificially drained areas. The aim of this study were (i) to estimate P loadings for individual flow fractions (point sources, surface runoff, tile flow, groundwater flow), spatially distributed on sub-basin scale. Since the official version of SWAT does not allow for the modeling of P in tile drains, we tested (ii) two different approaches of simulating P in tile drains by changing the SWAT source code. The SWAT source code was modified so that (i) the soluble P concentration of the groundwater was transferred to the tile water and (ii) the soluble P in the soil was transferred to the tiles. The SWAT model was first calibrated (2002-2011) and validated (1992-2001) for stream flow at 7 headwater catchments at a daily time scale. Based on this, the stream flow at the outlet of the Warnow river basin was simulated. Performance statistics indicated at least satisfactory model results for each sub-basin. Breaking down the discharge into flow constituents, it becomes visible that stream flow is mainly governed by groundwater and tile flow. Due to the topographic situation with gentle slopes, surface runoff played only a minor role. Results further indicate that the prediction of soluble P loads was improved by the modified SWAT versions. Major sources of P in rivers are groundwater and tile flow. P was also released by surface runoff during large storm events when sediment was eroded into the rivers. The contributions of point sources in terms of waste water treatment plants to the overall P loading were low. The modifications made in the SWAT source code should be considered as a starting point to simulate P loads in artificially drained landscapes more precisely. Further testing and development of the code is required.

Economic-environmental modeling of point source pollution in Jefferson County, Alabama, USA.

PubMed

Kebede, Ellene; Schreiner, Dean F; Huluka, Gobena

2002-05-01

This paper uses an integrated economic-environmental model to assess the point source pollution from major industries in Jefferson County, Northern Alabama. Industrial expansion generates employment, income, and tax revenue for the public sector; however, it is also often associated with the discharge of chemical pollutants. Jefferson County is one of the largest industrial counties in Alabama that experienced smog warnings and ambient ozone concentration, 1996-1999. Past studies of chemical discharge from industries have used models to assess the pollution impact of individual plants. This study, however, uses an extended Input-Output (I-O) economic model with pollution emission coefficients to assess direct and indirect pollutant emission for several major industries in Jefferson County. The major findings of the study are: (a) the principal emission by the selected industries are volatile organic compounds (VOC) and these contribute to the ambient ozone concentration; (b) the direct and indirect emissions are significantly higher than the direct emission by some industries, indicating that an isolated analysis will underestimate the emission by an industry; (c) while low emission coefficient industries may suggest industry choice they may also emit the most hazardous chemicals. This study is limited by the assumptions made, and the data availability, however it provides a useful analytical tool for direct and cumulative emission estimation and generates insights on the complexity in choice of industries.

Incorporation of Complex Hydrological and Socio-economic Factors for Non-point Source Pollution Control: A Case Study at the Yincungang Canal, the Lake Tai Basin of China

NASA Astrophysics Data System (ADS)

Yang, X.; Luo, X.; Zheng, Z.

2012-04-01

It is increasingly realized that non-point pollution sources contribute significantly to water environment deterioration in China. Compared to developed countries, non-point source pollution in China has the unique characteristics of strong intensity and composition complexity due to its special socioeconomic conditions. First, more than 50% of its 1.3 billion people are rural. Sewage from the majority of the rural households is discharged either without or only with minimal treatment. The large amount of erratic rural sewage discharge is a significant source of water pollution. Second, China is plagued with serious agricultural pollution due to widespread improper application of fertilizers and pesticides. Finally, there lack sufficient disposal and recycling of rural wastes such as livestock manure and crop straws. Pollutant loads from various sources have far exceeded environmental assimilation capacity in many parts of China. The Lake Tai basin is one typical example. Lake Tai is the third largest freshwater lake in China. The basin is located in the highly developed and densely populated Yangtze River Delta. While accounting for 0.4% of its land area and 2.9% of its population, the Lake Tai basin generates more than 14% of China's Gross Domestic Production (GDP), and the basin's GDP per capita is 3.5 times as much as the state average. Lake Tai is vital to the basin's socio-economic development, providing multiple services including water supply for municipal, industrial, and agricultural needs, navigation, flood control, fishery, and tourism. Unfortunately, accompanied with the fast economic development is serious water environment deterioration in the Lake Tai basin. The lake is becoming increasingly eutrophied and has frequently suffered from cyanobacterial blooms in recent decades. Chinese government has made tremendous investment in order to mitigate water pollution conditions in the basin. Nevertheless, the trend of deteriorating water quality has yet to be reversed. At least two factors contribute to the dichotomy between huge investment and limited results. First, the majority of the efforts have been limited to engineering approaches to water pollution control, ignoring the important roles of non-engineering approaches and stakeholder participation. Second, the complex hydrological regime of the basin may aggravate the impacts of various pollutant sources. Using the Yincungang canal, one major tributary to the Lake Tai, as an example, we discuss our work on both hydrological and socio-economic factors affecting the water quality of the canal, as well as the grand challenges of coupling hydrological systems and socio-economic systems in the region. Keywords non-point source pollution, rural sewage, agricultural pollution, spatio-temporal pattern, stakeholder participation

Natural products, their derivatives, mimics and synthetic equivalents: role in agrochemical discovery.

PubMed

Sparks, Thomas C; Hahn, Donald R; Garizi, Negar V

2017-04-01

Natural products (NPs) have a long history as a source of, and inspiration for, novel agrochemicals. Many of the existing herbicides, fungicides, and insecticides have their origins in a wide range of NPs from a variety of sources. Owing to the changing needs of agriculture, shifts in pest spectrum, development of resistance, and evolving regulatory requirements, the need for new agrochemical tools remains as critical as ever. As such, NPs continue to be an important source of models and templates for the development of new agrochemicals, demonstrated by the fact that NP models exist for many of the pest control agents that were discovered by other means. Interestingly, there appear to be distinct differences in the success of different NP sources for different pesticide uses. Although a few microbial NPs have been important starting points in recent discoveries of some insecticidal agrochemicals, historically plant sources have contributed the most to the discovery of new insecticides. In contrast, fungi have been the most important NP sources for new fungicides. Like insecticides, plant-sourced NPs have made the largest contribution to herbicide discovery. Available data on 2014 global sales and numbers of compounds in each class of pesticides indicate that the overall impact of NPs to the discovery of herbicides has been relatively modest compared to the impact observed for fungicides and insecticides. However, as new sourcing and approaches to NP discovery evolve, the impact of NPs in all agrochemical arenas will continue to expand. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Region 2 Port-area Investigation of Emissions Reduction (R2PIER)

EPA Science Inventory

Background Region 2 is home to the Port of New York and New Jersey (Port), the largest marine port on the East Coast and third largest in the nation. The Port is a concentrated source of diesel pollution, as more than 3 million containers move each year on diesel-powered ships, ...

Sources and loads of nutrients in the South Platte River, Colorado and Nebraska, 1994-95

USGS Publications Warehouse

Litke, D.W.

1996-01-01

The South Platte River Basin was one of 20 river basins selected in 1991 for investigation as part of the U.S. Geological Survey's National Water- Quality Assessment (NAWQA) Program. Nationwide, nutrients have been identified as one of the primary nationwide water-quality concerns and are of particular interest in the South Platte River Basin where nutrient concentrations are large compared to concentrations in other NAWQA river basins. This report presents estimates of the magnitude of nutrient-source inputs to the South Platte River Basin, describes nutrient concen- trations and loads in the South Platte River during different seasons, and presents comparisons of nutrient inputs to instream nutrient loads. Annual nutrient inputs to the basin were estimated to be 306,000 tons of nitrogen and 41,000 tons of phosphorus. The principal nutrient sources were wastewater-treatment plants, fertilizer and manure applications, and atmospheric deposition. To characterize nutrient concentrations and loads in the South Platte River during different seasons, five nutrient synoptic samplings were conducted during 1994 and 1995. Upstream from Denver, Colorado, during April 1994 and January 1995, total nitrogen concentrations were less than 2 milligrams per liter (mg/L), and total phosphorus concentrations were less than 0.2 mg/L. The water in the river at this point was derived mostly from forested land in the mountains west of Denver. Total nutrient concentrations increased through the Denver metropolitan area, and concentration peaks occurred just downstream from each of Denver's largest wastewater-treatment plants with maximum concentrations of 13.6 mg/L total nitrogen and 2.4 mg/L total phosphorus. Nutrient concen- concentrations generally decreased downstream from Denver. Upstream from Denver during April 1994 and January 1995, total nitrogen loads were less than 1,000 pounds per day (lb/d), and total phosphorus loads were less than 125 lb/d. Total nutrient loads increased through the Denver metropolitan area, and load peaks occurred just downstream from each of Denver's largest wastewater-treatment plants, with a maximum load of 14,000 lb/d total nitrogen and 2,300 lb/d total phosphorus. In April 1994, nutrient loads generally decreased from Henderson, Colorado, to North Platte, Nebraska. In January 1995, however, nutrient loads increased from Henderson to Kersey, Colorado (maximum loads of 31,000 lb/d total nitrogen and 3,000 lb/d total phosphorus), and then decreased from Kersey to North Platte. Seasonal nutrient loads primarily were dependent on streamflow. Total nitrogen loads were largest in June 1994 and January 1995 when streamflows also were largest. During June, streamflow was large, but nitrogen concentrations were small, which indicated that snowmelt runoff diluted the available supply of nitrogen. Total phosphorus loads were largest in June, when streamflow and phosphorus concentrations were large, which indicated an additional source of phosphorus during snowmelt runoff. Streamflow along the South Platte River was smallest in April and August 1994, and nutrient loads also were smallest during these months. The downstream pattern for nutrient loads did not vary much by season. Loads were large at Henderson, decreased between Henderson and Kersey, and usually were largest at Kersey. The magnitude of the decrease in loads between Henderson and Kersey varied between synoptics and was dependent on the amount of water removed by irrigation ditches. Nutrient loads leaving the basin were very small compared to the estimated total nutrient inputs to the basin. Streamflow balances indicated that the South Platte River is a gaining river throughout much of its length; streamflow-balance residuals were as large as 15 cubic feet per second per mile. Nutrient-load balances indicated that increases in river nitrate loads were, in some places, due to nitrification and, elsewhere, were due to the influx of nitrate-enriched ground water to

Radiocarbon determination of fossil and contemporary carbon contribution to aerosol in the Pacific Islands.

PubMed

Isley, C F; Nelson, P F; Taylor, M P; Williams, A A; Jacobsen, G E

2018-06-21

Combustion emissions are of growing concern across all Pacific Island Countries, which account for >10,000 km 2 of the earth's surface area; as for many other small island states globally. Apportioning emissions inputs for Suva, the largest Pacific Island city, will aid in development of emission reduction strategies. Total suspended particulate (TSP) and fine particulate (PM 2.5 ) samples were collected for Suva City, a residential area (Kinoya, TSP) and a mainly ocean-influenced site (Suva Point, TSP) from 2014 to 2015. Percentages of contemporary and fossil carbon were determined by radiocarbon analysis (accelerator mass spectrometry); for non‑carbonate carbon (NCC), elemental carbon (EC) and organic carbon (OC). Source contributions to particulate matter were identified and the accuracy of previous emissions inventory and source apportionment studies was evaluated. Suva Point NCC concentrations (2.7 ± 0.4 μg/m 3 ) were four times lower than for City (13 ± 2 μg/m 3 in TSP) and Kinoya (13 ± 1 μg/m 3 in TSP); demonstrating the contribution of land-based emissions activities in city and residential areas. In Suva City, total NCC in air was 81% (79%-83%) fossil carbon, from vehicles, shipping, power generation and industry; whilst in the residential area, 48% (46%-50%) of total NCC was contemporary carbon; reflecting the higher incidence of biomass and waste burning and of cooking activities. Secondary organic fossil carbon sources contributed >36% of NCC mass at the city and >29% at Kinoya; with biogenic carbon being Kinoya's most significant source (approx. 30% of NCC mass). These results support the previous source apportionment studies for the city area; yet show that, in line with emissions inventory studies, biomass combustion contributes more PM 2.5 mass in residential areas. Hence air quality management strategies need to target open burning activities as well as fossil fuel combustion. Copyright © 2018 Elsevier B.V. All rights reserved.

RESEARCH AREA -- MOBILE SOURCE EMISSIONS (EMISSIONS CHARACTERIZATION AND PREVENTION BRANCH, APPCD, NRMRL)

EPA Science Inventory

The objective of this program is to characterize mobile source emissions which are one of the largest sources of tropospheric ozone precursor emissions (CO, NOx, and volotile organic compounds) in the U.S. The research objective of the Emissions Characterization and Prevention Br...

Pell Grants as Performance-Based Scholarships? An Examination of Satisfactory Academic Progress Requirements in the Nation's Largest Need-Based Aid Program

ERIC Educational Resources Information Center

Schudde, Lauren; Scott-Clayton, Judith

2016-01-01

The Federal Pell Grant Program is the nation's largest need-based grant program. While students' initial eligibility for the Pell is based on financial need, renewal is contingent on meeting minimum academic standards similar to those in models of performance-based scholarships, including a grade point average (GPA) requirement and ratio of…

Impacts of Nitrogen Removal and Re-Application on N2O fluxes from Narragansett Bay: Contrasting Turfgrasses, Salt Marshes, and Wastewater Treatment Systems

NASA Astrophysics Data System (ADS)

Brannon, E.; Moseman-Valtierra, S.; Quinn, R. K.; Amador, J.; Brown, R.; Lancellotti, B.; Glennon, K.; Celeste, G.; Craver, V.

2016-12-01

Narragansett Bay in Rhode Island is characterized by a substantial, historic bay-wide nitrogen (N) gradient. Centralized wastewater treatment plants (WWTPs) are a major anthropogenic N source. Onsite wastewater treatments systems (OWTS), which serve 1/3 of all households in the state, are another anthropogenic N source. Recent state regulation has prompted upgrades to both WWTPs and OWTS to increase N removal capacities. Although this should lower N loads to Narragansett Bay, it has the potential to increase the flux of nitrous oxide (N2O), a potent greenhouse gas. We measured summer-time (2016) N2O fluxes of a major WWTP (biological N removal system at Field's Point in Providence) and three of the most common advanced OWTS in the Narragansett Bay watershed (Orenco Advantex AX20, BioMicrobics FAST, SeptiTech D Series). We also tested impacts of application of recovered N (biosolids from wastewater sludge) on N2O fluxes from a turfgrass (Schedonerus arundinaceus) and dominant native coastal cordgrass (Spartina alterniflora) in mesocosm experiments. Preliminary results indicate that the largest N2O fluxes (245 ± 72 µmol N2O m-2 h-1) were from the Field's Point WWTP. Significant, but smaller N2O fluxes (6 ± 3 µmol N2O m-2 h-1 were also measured from the OWTS. In contrast, N2O fluxes from the N-enriched native coastal cordgrass and turfgrass mesocosms were often non-detectable. However, fluxes from a few mesocosms (max. of 25 µmol N2O m-2 h-1) were on the same order of magnitude as fluxes from the OWTS. A state-wide budget of N2O emissions from turfgrasses, intertidal marshes, and OWTS will be estimated to determine their significance as sources relative to the Field's Point WWTP. This data will be used to identify areas where N2O fluxes can be minimized in the state of RI.

The 80 megawatt wind power project at Kahuku Point, Hawaii

NASA Technical Reports Server (NTRS)

Laessig, R. R.

1982-01-01

Windfarms Ltd. is developing the two largest wind energy projects in the world. Designed to produce 80 megawatts at Kahuku Point, Hawaii and 350 megawatts in Solano County, California, these projects will be the prototypes for future large-scale wind energy installations throughout the world.

Atmospheric aerosol composition and source apportionments to aerosol in southern Taiwan

NASA Astrophysics Data System (ADS)

Tsai, Ying I.; Chen, Chien-Lung

In this study, the chemical characteristics of winter aerosol at four sites in southern Taiwan were determined and the Gaussian Trajectory transfer coefficient model (GTx) was then used to identify the major air pollutant sources affecting the study sites. Aerosols were found to be acidic at all four sites. The most important constituents of the particulate matter (PM) by mass were SO 42-, organic carbon (OC), NO 3-, elemental carbon (EC) and NH 4+, with SO 42-, NO 3-, and NH 4+ together constituting 86.0-87.9% of the total PM 2.5 soluble inorganic salts and 68.9-78.3% of the total PM 2.5-10 soluble inorganic salts, showing that secondary photochemical solution components such as these were the major contributors to the aerosol water-soluble ions. The coastal site, Linyuan (LY), had the highest PM mass percentage of sea salts, higher in the coarse fraction, and higher sea salts during daytime than during nighttime, indicating that the prevailing daytime sea breeze brought with it more sea-salt aerosol. Other than sea salts, crustal matter, and EC in PM 2.5 at Jenwu (JW) and in PM 2.5-10 at LY, all aerosol components were higher during nighttime, due to relatively low nighttime mixing heights limiting vertical and horizontal dispersion. At JW, a site with heavy traffic loadings, the OC/EC ratio in the nighttime fine and coarse fractions of approximately 2.2 was higher than during daytime, indicating that in addition to primary organic aerosol (POA), secondary organic aerosol (SOA) also contributed to the nighttime PM 2.5. This was also true of the nighttime coarse fraction at LY. The GTx produced correlation coefficients ( r) for simulated and observed daily concentrations of PM 10 at the four sites (receptors) in the range 0.45-0.59 and biases from -6% to -20%. Source apportionment indicated that point sources were the largest PM 10 source at JW, LY and Daliao (DL), while at Meinung (MN), a suburban site with less local PM 10, SO x and NO x emissions, upwind boundary concentration was the major PM 10 source, followed by point sources and top boundary concentration.

Revisiting forest road retirement

Treesearch

Randy Kolka; Mathew Smidt

2001-01-01

Determining the sources of nonpoint source pollution in a watershed is difficult, although the largest source of sediment in forested systems is from skld trails, haul roads, and landings associated with forest harvest- ing (Ketcheson et al., 1999; Swft, 1988) The transport of sediment to streams and subsequent sedimentation leads to the loss of...

Availability of point-of-purchase nutrition information at a fast-food restaurant.

PubMed

Wootan, Margo G; Osborn, Melissa; Malloy, Claudia J

2006-12-01

Given the link between eating out, poor diets, and obesity, we assessed the availability of point-of-purchase nutrition information at the largest fast-food restaurant in the U.S., McDonald's. In August 2004, we visited 29 of 33 (88%) of the McDonald's outlets in Washington, DC and visually inspected the premises, as well as asked cashiers or restaurant managers whether they had nutrition information available in the restaurant. In Washington, DC, 59% of McDonald's outlets provided in-store nutrition information for the majority of their standard menu items. In 62% of the restaurants, it was necessary to ask two or more employees in order to obtain a copy of that information. We found that even at the largest chain restaurant in the country, nutrition information at the point of decision-making is often difficult to find or completely absent.

Mercury Isotopes in Earth and Environmental Sciences

NASA Astrophysics Data System (ADS)

Blum, Joel D.; Sherman, Laura S.; Johnson, Marcus W.

2014-05-01

Virtually all biotic, dark abiotic, and photochemical transformations of mercury (Hg) produce Hg isotope fractionation, which can be either mass dependent (MDF) or mass independent (MIF). The largest range in MDF is observed among geological materials and rainfall impacted by anthropogenic sources. The largest positive MIF of Hg isotopes (odd-mass excess) is caused by photochemical degradation of methylmercury in water. This signature is retained through the food web and measured in all freshwater and marine fish. The largest negative MIF of Hg isotopes (odd-mass deficit) is caused by photochemical reduction of inorganic Hg and has been observed in Arctic snow and plant foliage. Ratios of MDF to MIF and ratios of 199Hg MIF to 201Hg MIF are often diagnostic of biogeochemical reaction pathways. More than a decade of research demonstrates that Hg isotopes can be used to trace sources, biogeochemical cycling, and reactions involving Hg in the environment.

Three-dimensional simulations of ground motions in the San Bernardino Valley, California, for hypothetical earthquakes on the San Andreas Fault

USGS Publications Warehouse

Frankel, A.

1993-01-01

Three-dimensional finite difference simulations of elastic waves in the San Bernardino Valley were performed for two hypothetical earthquakes on the San Andreas fault: a point source with moment magnitude M5 and an extended rupture with M6.5. A method is presented for incorporating a source with arbitrary focal mechanism in the grid. Synthetics from the 3-D simulations are compared with those derived from 2-D (vertical cross section) and 1-D (flat-layered) models. The synthetic seismograms from the 3-D and 2-D simulations exhibit large surface waves produced by conversion of incident S waves at the edge of the basin. Seismograms from the flat-layered model do not contain these converted surface waves and underestimate the duration of shaking. Maps of maximum ground velocities occur in localized portions of the basin. The location of the largest velocities changes with the rupture propagation direction. Contours of maximum shaking are also dependent on asperity positions and radiation pattern. -from Author

Occurrence Characteristics of Microplastic in Secondary Sewage Treatment Plant in Shanghai,China.

NASA Astrophysics Data System (ADS)

Bai, M.; Zhao, S.; Li, D.

2017-12-01

As emerging pollutants, microplastics (MPs) are of concern worldwide. Due to plenty of microbeads and synthetic fibers presenting in the effluent of waste water treatment plants (WWTPs), WWTPs have been regarded as important point sources of MP into the sea. Currently, information of microplastics from WWTPs in China is limited. Herein, we studied the MP contamination of a sewage plant in Shanghai by analyzing water and sludge samples with fourier transform infrared spectroscopy. The abundances of MP in the influent, mixed water, effluent and sludge four stages are respectively 117 n/L, 90 n/L, 52 n/L and 181 n/50g(wet weight). The removal efficiency of MP in the current WWTP is 55.6%. Fiber is the most common shape type. Rayon is the most type in effluent and mixed water while synthetic leather account for the largest percentage in influent and sludge. This study firstly discussed the occurrence characteristics of microplastics in the WWTP of China and confirmed that WWTP is a source of MPs inputting into aquatic environments.

Analysis of streamflow distribution of non-point source nitrogen export from long-term urban-rural catchments to guide watershed management in the Chesapeake Bay watershed

NASA Astrophysics Data System (ADS)

Duncan, J. M.; Band, L. E.; Groffman, P.

2017-12-01

Discharge, land use, and watershed management practices (stream restoration and stormwater control measures) have been found to be important determinants of nitrogen (N) export to receiving waters. We used long-term water quality stations from the Baltimore Ecosystem Study Long-Term Ecological Research (BES LTER) Site to quantify nitrogen export across streamflow conditions at the small watershed scale. We calculated nitrate and total nitrogen fluxes using methodology that allows for changes over time; weighted regressions on time, discharge, and seasonality. Here we tested the hypotheses that a) while the largest N stream fluxes occur during storm events, there is not a clear relationship between N flux and discharge and b) N export patterns are aseasonal in developed watersheds where sources are larger and retention capacity is lower. The goal is to scale understanding from small watersheds to larger ones. Developing a better understanding of hydrologic controls on nitrogen export is essential for successful adaptive watershed management at societally meaningful spatial scales.

Source Apportionment of Particulate Matter Collected Upwind and Downwind of a Steel Facility in Granite City, IL (USA)

NASA Astrophysics Data System (ADS)

Duvall, R. M.; Norris, G. A.; Willis, R. D.; Turner, J. R.; Kaleel, R.; Sweitzer, T.; Preston, B.; Hays, M. D.

2009-04-01

St. Louis is currently in nonattainment of the annual PM2.5 National Ambient Air Quality Standard (NAAQS). Granite City Steel Works (GSCW), located in Granite City, IL is considered to be a significant source impacting the St. Louis area and the largest PM2.5 point source contributor. Twelve grab samples were collected in and around the steel facility including the basic oxygen furnace, steel and iron slag crushing, coal pulverizing, baghouse dust, paved road dust, and unpaved road dust. The bulk samples were resuspended in a resuspension chamber using a PM2.5 cutpoint and collected on Teflon, quartz and polycarbonate filters. Fine particulate matter (PM) samples (12-hr and 24-hr) were collected upwind and downwind of GSCW from October 13 to December 13, 2007 to identify sources contributing to nonattainment in St. Louis. The samples were analyzed for trace metals (X-Ray Fluorescence), ions (Ion Chromatography), elemental and organic carbon (thermal optical analysis), and organic species (solvent extraction Gas Chromatography/Mass Spectrometry). Source apportionment was conducted using the EPA Chemical Mass Balance (CMB) Model (v 8.2). Major sources impacting the 12-hr samples included the blast oxygen furnace, secondary sulfate, and road dust. Higher excess steel and coke works contributions were associated with higher wind speeds (greater than 5 mph) and more variability in source impacts was observed. Major sources impacting the 24-hr samples included secondary sulfate and motor vehicles (diesel and gasoline). Contributions were similar between the coke and steel works sources. Disclaimer: Although this work was reviewed by EPA and approved for publication, it may not necessarily reflect official Agency policy.

RCSLenS: The Red Cluster Sequence Lensing Survey

NASA Astrophysics Data System (ADS)

Hildebrandt, H.; Choi, A.; Heymans, C.; Blake, C.; Erben, T.; Miller, L.; Nakajima, R.; van Waerbeke, L.; Viola, M.; Buddendiek, A.; Harnois-Déraps, J.; Hojjati, A.; Joachimi, B.; Joudaki, S.; Kitching, T. D.; Wolf, C.; Gwyn, S.; Johnson, N.; Kuijken, K.; Sheikhbahaee, Z.; Tudorica, A.; Yee, H. K. C.

2016-11-01

We present the Red Cluster Sequence Lensing Survey (RCSLenS), an application of the methods developed for the Canada-France-Hawaii Telescope Lensing Survey (CFHTLenS) to the ˜785 deg2, multi-band imaging data of the Red-sequence Cluster Survey 2. This project represents the largest public, sub-arcsecond seeing, multi-band survey to date that is suited for weak gravitational lensing measurements. With a careful assessment of systematic errors in shape measurements and photometric redshifts, we extend the use of this data set to allow cross-correlation analyses between weak lensing observables and other data sets. We describe the imaging data, the data reduction, masking, multi-colour photometry, photometric redshifts, shape measurements, tests for systematic errors, and a blinding scheme to allow for more objective measurements. In total, we analyse 761 pointings with r-band coverage, which constitutes our lensing sample. Residual large-scale B-mode systematics prevent the use of this shear catalogue for cosmic shear science. The effective number density of lensing sources over an unmasked area of 571.7 deg2 and down to a magnitude limit of r ˜ 24.5 is 8.1 galaxies per arcmin2 (weighted: 5.5 arcmin-2) distributed over 14 patches on the sky. Photometric redshifts based on four-band griz data are available for 513 pointings covering an unmasked area of 383.5 deg2. We present weak lensing mass reconstructions of some example clusters as well as the full survey representing the largest areas that have been mapped in this way. All our data products are publicly available through Canadian Astronomy Data Centre at http://www.cadc-ccda.hia-iha.nrc-cnrc.gc.ca/en/community/rcslens/query.html in a format very similar to the CFHTLenS data release.

Ammonia concentrations at a site in Southern Scotland from 2 yr of continuous measurements

NASA Astrophysics Data System (ADS)

Burkhardt, J.; Sutton, M. A.; Milford, C.; Storeton-West, R. L.; Fowler, D.

Atmospheric ammonia (NH 3) concentrations were measured using a continuous-flow annular denuder over a period of 2 yr at a rural site near Edinburgh, Scotland. Meteorological parameters as well as sulphur dioxide (SO 2) concentrations were also recorded. The overall arithmetic mean NH 3 concentration was 1.4 μg m -3. Although an annual cycle with largest NH 3 concentrations in summer was apparent for seasonal geometric mean concentrations, arithmetic mean concentrations were largest in the spring and autumn, indicating the increased importance of occasional high concentration events in these seasons. The NH 3 concentrations were influenced by local sources as well as by background concentrations, dependent on wind direction, whereas SO 2 geometric standard deviations indicated more distant sources. The daily cycle of NH 3 and SO 2 concentrations was dependent on wind speed ( u). At u<1 m s -1, NH 3 concentrations were smallest and SO 2 concentrations were largest around noon, whereas at u>1 m s -1 this cycle was less pronounced for both gases and NH 3 concentrations were largest around 1800 hours. These opposite diurnal cycles may be explained by the interaction of boundary layer mixing with local sources for NH 3 and remote sources for SO 2. Comparing the ammonia data with critical levels and critical loads shows that the critical level is not exceeded at this site over any averaging time. In contrast, the N critical load would probably be exceeded for moorland vegetation near this site, showing that the contribution of atmospheric NH 3 to nitrogen deposition in the long term is a more significant issue than exceedance of critical levels.

The Herschel–ATLAS Data Release 2, Paper I. Submillimeter and Far-infrared Images of the South and North Galactic Poles: The Largest Herschel Survey of the Extragalactic Sky

NASA Astrophysics Data System (ADS)

Smith, Matthew W. L.; Ibar, Edo; Maddox, Steve J.; Valiante, Elisabetta; Dunne, Loretta; Eales, Stephen; Dye, Simon; Furlanetto, Christina; Bourne, Nathan; Cigan, Phil; Ivison, Rob J.; Gomez, Haley; Smith, Daniel J. B.; Viaene, Sébastien

2017-12-01

We present the largest submillimeter images that have been made of the extragalactic sky. The Herschel Astrophysical Terahertz Large Area Survey (H-ATLAS) is a survey of 660 deg2 with the PACS and SPIRE cameras in five photometric bands: 100, 160, 250, 350, and 500 μm. In this paper we present the images from our two largest fields, which account for ∼75% of the survey. The first field is 180.1 deg2 in size, centered on the north Galactic pole (NGP), and the second is 317.6 deg2 in size, centered on the south Galactic pole. The NGP field serendipitously contains the Coma cluster. Over most (∼80%) of the images, the pixel noise, including both instrumental noise and confusion noise, is approximately 3.6, and 3.5 mJy pix‑1 at 100 and 160 μm, and 11.0, 11.1 and 12.3 mJy beam‑1 at 250, 350 and 500 μm, respectively, but reaches lower values in some parts of the images. If a matched filter is applied to optimize point-source detection, our total 1σ map sensitivity is 5.7, 6.0, and 7.3 mJy at 250, 350, and 500 μm, respectively. We describe the results of an investigation of the noise properties of the images. We make the most precise estimate of confusion in SPIRE maps to date, finding values of 3.12 ± 0.07, 4.13 ± 0.02, and 4.45 ± 0.04 mJy beam‑1 at 250, 350, and 500 μm in our un-convolved maps. For PACS we find an estimate of the confusion noise in our fast-parallel observations of 4.23 and 4.62 mJy beam‑1 at 100 and 160 μm. Finally, we give recipes for using these images to carry out photometry, both for unresolved and extended sources.

Source parameters controlling the generation and propagation of potential local tsunamis along the cascadia margin

USGS Publications Warehouse

Geist, E.; Yoshioka, S.

1996-01-01

The largest uncertainty in assessing hazards from local tsunamis along the Cascadia margin is estimating the possible earthquake source parameters. We investigate which source parameters exert the largest influence on tsunami generation and determine how each parameter affects the amplitude of the local tsunami. The following source parameters were analyzed: (1) type of faulting characteristic of the Cascadia subduction zone, (2) amount of slip during rupture, (3) slip orientation, (4) duration of rupture, (5) physical properties of the accretionary wedge, and (6) influence of secondary faulting. The effect of each of these source parameters on the quasi-static displacement of the ocean floor is determined by using elastic three-dimensional, finite-element models. The propagation of the resulting tsunami is modeled both near the coastline using the two-dimensional (x-t) Peregrine equations that includes the effects of dispersion and near the source using the three-dimensional (x-y-t) linear long-wave equations. The source parameters that have the largest influence on local tsunami excitation are the shallowness of rupture and the amount of slip. In addition, the orientation of slip has a large effect on the directivity of the tsunami, especially for shallow dipping faults, which consequently has a direct influence on the length of coastline inundated by the tsunami. Duration of rupture, physical properties of the accretionary wedge, and secondary faulting all affect the excitation of tsunamis but to a lesser extent than the shallowness of rupture and the amount and orientation of slip. Assessment of the severity of the local tsunami hazard should take into account that relatively large tsunamis can be generated from anomalous 'tsunami earthquakes' that rupture within the accretionary wedge in comparison to interplate thrust earthquakes of similar magnitude. ?? 1996 Kluwer Academic Publishers.

Future trends in electrical energy generation economics in the United States

NASA Technical Reports Server (NTRS)

Schmitt, R. W.; Fox, G. R.; Shah, R. P.; Stewart, P. J.; Vermilyea, D. A.

1977-01-01

Developments related to the economics of coal-fired systems in the U.S. are mainly considered. The historical background of the U.S. electric generation industry is examined and the U.S. electrical generation characteristics in the year 1975 are considered. It is pointed out that coal-fired power plants are presently the largest source of electrical energy generation in the U.S. Questions concerning the availability and quality of coal are investigated. Currently there are plans for converting some 50 large oil and gas-fired generating plants to coal, and it is expected that coal will be the fuel used in almost all fossil-fired base load additions to generating capacity. Aspects of advanced energy conversion from coal are discussed, taking into account the performance and economic potential of the energy conversion systems.

Monoterpenes are the largest source of summertime organic aerosol in the southeastern United States

DOE PAGES

Zhang, Haofei; Yee, Lindsay D.; Lee, Ben H.; ...

2018-02-12

The chemical complexity of atmospheric organic aerosol (OA) has caused substantial uncertainties in understanding its origins and environmental impacts. Here, we provide constraints on OA origins through compositional characterization with molecular-level details. Our results suggest that secondary OA (SOA) from monoterpene oxidation accounts for approximately half of summertime fine OA in Centreville, AL, a forested area in the southeastern United States influenced by anthropogenic pollution. We find that different chemical processes involving nitrogen oxides, during days and nights, play a central role in determining the mass of monoterpene SOA produced. These findings elucidate the strong anthropogenic–biogenic interaction affecting ambient aerosolmore » in the southeastern United States and point out the importance of reducing anthropogenic emissions, especially under a changing climate, where biogenic emissions will likely keep increasing.« less

Monoterpenes are the largest source of summertime organic aerosol in the southeastern United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Haofei; Yee, Lindsay D.; Lee, Ben H.

The chemical complexity of atmospheric organic aerosol (OA) has caused substantial uncertainties in understanding its origins and environmental impacts. Here, we provide constraints on OA origins through compositional characterization with molecular-level details. Our results suggest that secondary OA (SOA) from monoterpene oxidation accounts for approximately half of summertime fine OA in Centreville, AL, a forested area in the southeastern United States influenced by anthropogenic pollution. We find that different chemical processes involving nitrogen oxides, during days and nights, play a central role in determining the mass of monoterpene SOA produced. These findings elucidate the strong anthropogenic–biogenic interaction affecting ambient aerosolmore » in the southeastern United States and point out the importance of reducing anthropogenic emissions, especially under a changing climate, where biogenic emissions will likely keep increasing.« less

Treatability Aspects of Urban Stormwater Stressors

EPA Science Inventory

Eleven years into the 21st century, pollution from diffuse sources (pollution from contaminants picked up and carried into surface waters by stormwater runoff) remains the nation's largest source of water quality problems. Scientists and engineers still seek solutions that will ...

A mass transfer model of ethanol emission from thin layers of corn silage

USDA-ARS?s Scientific Manuscript database

Dairies may be important emission sources for volatile organic compounds (VOCs). Reactive organic gases (ROG) emissions from dairy farms are the second largest source responsible for ozone formation in the California’s San Joaquin Valley. Animal feed was found to be a major ROG emission source on da...

River Export of Plastic from Land to Sea: A Global Modeling Approach

NASA Astrophysics Data System (ADS)

Siegfried, Max; Gabbert, Silke; Koelmans, Albert A.; Kroeze, Carolien; Löhr, Ansje; Verburg, Charlotte

2016-04-01

Plastic is increasingly considered a serious cause of water pollution. It is a threat to aquatic ecosystems, including rivers, coastal waters and oceans. Rivers transport considerable amounts of plastic from land to sea. The quantity and its main sources, however, are not well known. Assessing the amount of macro- and microplastic transport from river to sea is, therefore, important for understanding the dimension and the patterns of plastic pollution of aquatic ecosystems. In addition, it is crucial for assessing short- and long-term impacts caused by plastic pollution. Here we present a global modelling approach to quantify river export of plastic from land to sea. Our approach accounts for different types of plastic, including both macro- and micro-plastics. Moreover, we distinguish point sources and diffuse sources of plastic in rivers. Our modelling approach is inspired by global nutrient models, which include more than 6000 river basins. In this paper, we will present our modelling approach, as well as first model results for micro-plastic pollution in European rivers. Important sources of micro-plastics include personal care products, laundry, household dust and car tyre wear. We combine information on these sources with information on sewage management, and plastic retention during river transport for the largest European rivers. Our modelling approach may help to better understand and prevent water pollution by plastic , and at the same time serves as 'proof of concept' for future application on global scale.

A Sleeping Giant Awakened: Reignition of AGN Activity, Reborn Star Formation, and a Multiphase Outflow in one of the Largest Radio Galaxies Known

NASA Astrophysics Data System (ADS)

Tremblay, Grant; O'Dea, Christopher; Labiano, Alvaro; Baum, Stefi; McDermid, Richard; Combes, Francoise; Garcia-Burillo, Santiago; Davis, Timothy

2014-08-01

3C 236 is the second largest known radio galaxy and one of the largest objects in the known Universe. Its central AGN has recently reignited after a 10 Myr dormancy period, giving rise to a very young and compact radio source and a 1000 km/sec outflow of warm ionized and atomic HI gas. We propose GMOS-N IFU observations to resolve this outflow, determine its driver, and estimate the relative coupling efficiencies between the warm ionized, atomic, and cold molecular gas phases. We will assemble a much-needed spatially resolved Balmer decrement (extinction map) across the dramatic double dust lanes of this source, enabling high spatial resolution star formation rate, efficiency, and gas excitation and velocity maps. These will address several mysteries related to the very high star formation efficiency and the unique nature of the multiphase outflow in this source. 3C 236 is such a remarkable galaxy that whatever the results of the proposed observations, they will have wide-ranging implications for the triggering of star formation and AGN activity, their possibly coupled co-evolution, and the feedback effects of the latter on the former.

Treatability Aspects of Urban Stormwater Stressors - journal

EPA Science Inventory

Eleven years into the 21st century, pollution from diffuse sources (pollution from contaminants picked up and carried into surface waters by stormwater runoff) remains the nation's largest source of water quality problems. Scientists and engineers still seek solutions that will a...

Treatability Aspects of Urban Stormwater Stressors - paper

EPA Science Inventory

Eleven years into the 21st century, pollution from diffuse sources (pollution from contaminants picked up and carried into surface waters by stormwater runoff) remains the nation's largest source of water quality problems. Scientists and engineers still seek solutions that will a...

MO-D-213-07: RadShield: Semi- Automated Calculation of Air Kerma Rate and Barrier Thickness

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeLorenzo, M; Wu, D; Rutel, I

2015-06-15

Purpose: To develop the first Java-based semi-automated calculation program intended to aid professional radiation shielding design. Air-kerma rate and barrier thickness calculations are performed by implementing NCRP Report 147 formalism into a Graphical User Interface (GUI). The ultimate aim of this newly created software package is to reduce errors and improve radiographic and fluoroscopic room designs over manual approaches. Methods: Floor plans are first imported as images into the RadShield software program. These plans serve as templates for drawing barriers, occupied regions and x-ray tube locations. We have implemented sub-GUIs that allow the specification in regions and equipment for occupancymore » factors, design goals, number of patients, primary beam directions, source-to-patient distances and workload distributions. Once the user enters the above parameters, the program automatically calculates air-kerma rate at sampled points beyond all barriers. For each sample point, a corresponding minimum barrier thickness is calculated to meet the design goal. RadShield allows control over preshielding, sample point location and material types. Results: A functional GUI package was developed and tested. Examination of sample walls and source distributions yields a maximum percent difference of less than 0.1% between hand-calculated air-kerma rates and RadShield. Conclusion: The initial results demonstrated that RadShield calculates air-kerma rates and required barrier thicknesses with reliable accuracy and can be used to make radiation shielding design more efficient and accurate. This newly developed approach differs from conventional calculation methods in that it finds air-kerma rates and thickness requirements for many points outside the barriers, stores the information and selects the largest value needed to comply with NCRP Report 147 design goals. Floor plans, parameters, designs and reports can be saved and accessed later for modification and recalculation. We have confirmed that this software accurately calculates air-kerma rates and required barrier thicknesses for diagnostic radiography and fluoroscopic rooms.« less

Chemical Composition and Source Apportionment of high temporal resolution PM1 data for January-August 2017 in Delhi, India

NASA Astrophysics Data System (ADS)

Bhandari, S.; Wang, D. S.; Gani, S.; Seraj, S.; Arub, Z.; Habib, G.; Apte, J.; Hildebrandt Ruiz, L.

2017-12-01

Exposure to fine particulate matter (PM) poses significant health risks, especially to residents in heavily populated areas. The current understanding of the sources and dynamics of PM pollution in developing countries like India is limited. Delhi, India is the second most populated city in the world that has extremely high winter PM concentrations and frequent severe pollution episodes. This study reports on composition measurements of submicron aerosol at 1 minute time resolution from January to August of 2017, collected at the Indian Institute of Technology Delhi using an Aerodyne Aerosol Chemical Speciation Monitor (ACSM) and black carbon (BC) measurements using an Aethalometer. Source apportionment was conducted on organic and inorganic mass spectra measured by the ACSM and black carbon data measured using Positive Matrix Factorization (PMF). High concentrations of particulate matter were observed with total PM1 at times exceeding 200 µg m-3 in winter. A significant drop in PM1 concentrations was observed in the winter-spring transition. As observed elsewhere, organic species dominated the submicron mass, contributing 60% of the total mass over the duration of the campaign. However, this fractional contribution varied substantially over the day: from 48% early in the morning to 73% late at night. Along with diurnal variation in total PM1 mass loadings, particulate chloride levels also exhibited a strong diurnal cycle, with concentrations as high as 50 µg m-3 observed in the early mornings of January 2017. Literature review on identification of winter chloride sources in Delhi points to local and regional sources such as biomass/open-waste burning and coal combustion. PMF receptor modeling identified several factors with distinct diurnal patterns. While hydrocarbon-like organic aerosol (HOA) factor has the largest mass fraction contribution, PMF results consistently suggest chloride presence as attributable to ammonium chloride. Interestingly, aerosol neutralization characterization shows an apparent acidity of aerosols. These results point to substantial differences in aerosol composition in Indian cities in comparison to cities around the world, especially with regards to the abundance of particulate chloride, and provide insights into the sources of PM1 measured in Delhi.

Permitted water use in Iowa, 1985

USGS Publications Warehouse

Runkle, D.L.; Newman, J.L.; Shields, E.M.

1985-01-01

This report summarizes where, how much and for what purpose water is allocated for use in Iowa with permits issued by the Department of Water, Air and Waste Management. In Iowa, from a total permitted water use of 855,175.45 million gallons per year, about 58 percent is from surface-water sources and about 42 percent is from ground-water sources. Streams are 80.5 percent of the total surface-water use and wells make up 80.1 percent of the total ground-water use, with 65.4 percent of ground water coming from surficial aquifers. Power generation is the use category that is permitted the largest amount of total water use, 46.6 percent, with surface water being the source of 96.7 percent and 77.9 percent of the surface water is from streams. The public water suppliers' category is the next largest use type with 15.7 percent of the total permitted water. Ground water constitutes 74.4 percent of the public water supplier category with 51.7 percent from surficial aquifers. Surface water makes up 25.6 percent of this category with 83.0 percent of the surface water withdrawn from streams. Mining comprises 13.4 percent of the total water use and is the third largest water-use category. Ground water is the source of 63.3 percent of permitted mining water use with 94.3 percent of this from quarries and sand and gravel pits. Surface water is the source of 36.7 percent of the permitted mining water use with 97.6 percent from streams. Irrigation is the fourth largest permitted use type using 12.0 percent of the total water use. Eighty-eight percent of irrigation is from ground-water sources where surficial aquifers account for 94.7 percent. Streams are 81.1 percent of irrigational surface-water use. Self-supplied industrial users are permitted 10.6 percent of the total permitted water use with 85.5 percent of this from ground-water sources and 14.5 percent from surface-water sources. Of the self-supplied industrial ground-water use, 47.9 percent comes from surficial aquifers and of the self-supplied industrial surface-water use 86.1 percent is from streams. Self-supplied commercial use is allocated 1.5 percent of the total permitted water. Surface-water is the source of 37.7 percent of this and 62.3 percent is from ground-water sources. Agricultural (non-irrigation) use is 0.3 percent of the total permitted water with 73.3 percent from groundwater sources and 26.7 percent from surface-water sources. The areas that are allocated the most water permits are east-central Iowa and west-central Iowa.

Global Source-Receptor Relationships for Mercury Deposition Under Present-Day and 2050 Emissions Scenarios

PubMed Central

Corbitt, Elizabeth S.; Jacob, Daniel J.; Holmes, Christopher D.; Streets, David G.; Sunderland, Elsie M.

2011-01-01

Global policies regulating anthropogenic mercury require an understanding of the relationship between emitted and deposited mercury on intercontinental scales. Here we examine source-receptor relationships for present-day conditions and for four 2050 IPCC scenarios encompassing a range of economic development and environmental regulation projections. We use the GEOS-Chem global model to track mercury from its point of emission through rapid cycling in surface ocean and land reservoirs to its accumulation in longer-lived ocean and soil pools. Deposited mercury has a local component (emitted HgII, lifetime of 3.7 days against deposition) and a global component (emitted Hg0, lifetime of 6 months against deposition). Fast recycling of deposited mercury through photoreduction of HgII and re-emission of Hg0 from surface reservoirs (ice, land, surface ocean) increases the effective lifetime of anthropogenic mercury to 9 months against loss to legacy reservoirs (soil pools and the subsurface ocean). This lifetime is still sufficiently short that source-receptor relationships have a strong hemispheric signature. Asian emissions are the largest source of anthropogenic deposition to all ocean basins, though there is also regional source influence from upwind continents. Current anthropogenic emissions account for only about one-third of mercury deposition to the global ocean with the remainder from natural and legacy sources. However, controls on anthropogenic emissions would have the added benefit of reducing the legacy mercury re-emitted to the atmosphere. Better understanding is needed of the timescales for transfer of mercury from active pools to stable geochemical reservoirs. PMID:22050654

OPTICAL SPECTROSCOPIC OBSERVATIONS OF GAMMA-RAY BLAZAR CANDIDATES. VI. FURTHER OBSERVATIONS FROM TNG, WHT, OAN, SOAR, AND MAGELLAN TELESCOPES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Álvarez Crespo, N.; Massaro, F.; Milisavljevic, D.

Blazars, one of the most extreme classes of active galaxies, constitute so far the largest known population of γ-ray sources, and their number is continuously growing in the Fermi catalogs. However, in the latest release of the Fermi catalog there is still a large fraction of sources that are classified as blazar candidates of uncertain type (BCUs) for which optical spectroscopic observations are necessary to confirm their nature and their associations. In addition, about one-third of the γ-ray point sources listed in the Third Fermi-LAT Source Catalog (3FGL) are still unassociated and lacking an assigned lower-energy counterpart. Since 2012 wemore » have been carrying out an optical spectroscopic campaign to observe blazar candidates to confirm their nature. In this paper, the sixth of the series, we present optical spectroscopic observations for 30 γ-ray blazar candidates from different observing programs we carried out with the Telescopio Nazionale Galileo, William Herschel Telescope, Observatorio Astronómico Nacional, Southern Astrophysical Research Telescope, and Magellan Telescopes. We found that 21 out of 30 sources investigated are BL Lac objects, while the remaining targets are classified as flat-spectrum radio quasars showing the typical broad emission lines of normal quasi-stellar objects. We conclude that our selection of γ-ray blazar candidates based on their multifrequency properties continues to be a successful way to discover potential low-energy counterparts of the Fermi unidentified gamma-ray sources and to confirm the nature of BCUs.« less

Ball bearing vibrations amplitude modeling and test comparisons

NASA Technical Reports Server (NTRS)

Hightower, Richard A., III; Bailey, Dave

1995-01-01

Bearings generate disturbances that, when combined with structural gains of a momentum wheel, contribute to induced vibration in the wheel. The frequencies generated by a ball bearing are defined by the bearing's geometry and defects. The amplitudes at these frequencies are dependent upon the actual geometry variations from perfection; therefore, a geometrically perfect bearing will produce no amplitudes at the kinematic frequencies that the design generates. Because perfect geometry can only be approached, emitted vibrations do occur. The most significant vibration is at the spin frequency and can be balanced out in the build process. Other frequencies' amplitudes, however, cannot be balanced out. Momentum wheels are usually the single largest source of vibrations in a spacecraft and can contribute to pointing inaccuracies if emitted vibrations ring the structure or are in the high-gain bandwidth of a sensitive pointing control loop. It is therefore important to be able to provide an a priori knowledge of possible amplitudes that are singular in source or are a result of interacting defects that do not reveal themselves in normal frequency prediction equations. This paper will describe the computer model that provides for the incorporation of bearing geometry errors and then develops an estimation of actual amplitudes and frequencies. Test results were correlated with the model. A momentum wheel was producing an unacceptable 74 Hz amplitude. The model was used to simulate geometry errors and proved successful in identifying a cause that was verified when the parts were inspected.

Long-term Postseismic Deformation Following the 1964 Alaska Earthquake

NASA Astrophysics Data System (ADS)

Freymueller, J. T.; Cohen, S. C.; Hreinsdöttir, S.; Suito, H.

2003-12-01

Geodetic data provide a rich data set describing the postseismic deformation that followed the 1964 Alaska earthquake (Mw 9.2). This is particularly true for vertical deformation, since tide gauges and leveling surveys provide extensive spatial coverage. Leveling was carried out over all of the major roads of Alaska in 1964-65, and over the last several years we have resurveyed an extensive data set using GPS. Along Turnagain Arm of Cook Inlet, south of Anchorage, a trench-normal profile was surveyed repeatedly over the first decade after the earthquake, and many of these sites have been surveyed with GPS. After using a geoid model to correct for the difference between geometric and orthometric heights, the leveling+GPS surveys reveal up to 1.25 meters of uplift since 1964. The largest uplifts are concentrated in the northern part of the Kenai Peninsula, SW of Turnagain Arm. In some places, steep gradients in the cumulative uplift measurements point to a very shallow source for the deformation. The average 1964-late 1990s uplift rates were substantially higher than the present-day uplift rates, which rarely exceed 10 mm/yr. Both leveling and tide gauge data document a decay in uplift rate over time as the postseismic signal decreases. However, even today the postseismic deformation represents a substantial portion of the total observe deformation signal, illustrating that very long-lived postseismic deformation is an important element of the subduction zone earthquake cycle for the very largest earthquakes. This is in contrast to much smaller events, such as M~8 earthquakes, for which postseismic deformation in many cases decays within a few years. This suggests that the very largest earthquakes may excite different processes than smaller events.

Medical information on the Internet: Quality assessment of lumbar puncture and neuroaxial block techniques on YouTube.

PubMed

Rössler, Bernhard; Lahner, Daniel; Schebesta, Karl; Chiari, Astrid; Plöchl, Walter

2012-07-01

The Internet has become the largest, most up-to-date source for medical information. Besides enhancing patients' knowledge, the freely accessible audio-visual files have an impact on medical education. However little is known about their characteristics. In this manuscript the quality of lumbar puncture (LP) and spinal anaesthesia (SA) videos available on YouTube is assessed. This retrospective analysis was based on a search for LP and SA on YouTube. Videos were evaluated using essential key points (5 in SA, 4 in LP) and 3 safety indicators. Furthermore, violation of sterile working techniques and a rating whether the video must be regarded as dangerously misleading was performed. From 2321 hits matching the keywords, 38 videos were eligible for evaluation. In LP videos, 14% contained information on all, 4.5% on 3 and 4.5% on 2 key points, 59% on 1 and 18% on no key point. Regarding SA, no video contained information on all 5 key points, 56% on 2-4 and 25% on 1 key point, 19% did not contain any essential information. A sterility violation occurred in 11%, and 13% were classified as dangerously misleading. Even though high quality videos are available, the quality of video clips is generally low. The fraction of videos that were not performed in an aseptic manner is low, but these pose a substantial risk to patients. Consequently, more high-quality, institutional medical learning videos must be made available in the light of the increased utilization on the Internet. Copyright © 2012 Elsevier B.V. All rights reserved.

THE ASSOCIATION OF LAND USE/LAND COVER AND NUTRIENT LEVELS IN MARYLAND STREAMS

EPA Science Inventory

Anthropogenic nonpoint sources of nutrients are known to cause accelerated eutrophication of estuaries. The Chesapeake Bay is one of the world's largest estuaries exhibiting the eutrophication problem caused by pollution from various land use activities. The sources contributing ...

Research on the Emission Inventory of Major Air Pollutants in 2012 for the Sichuan City Cluster in China

NASA Astrophysics Data System (ADS)

Qian, J.; He, Q.

2014-12-01

This paper developed a high resolution emission inventory of major pollutants in city cluster of Sichuan Basin, one of the most polluted regions in China. The city cluster included five cities, which were Chengdu, Deyang, Mianyang, Meishan and Ziyang. Pollution source census and field measurements were conducted for the major emission sources such as the industry sources, on-road mobile sources, catering sources and the dust sources. The inventory results showed that in the year of 2012, the emission of SO2、NOX、CO、PM10、PM2.5、VOCs and NH3 in the region were 143.5、251.9、1659.9、299.3、163.5、464.1 and 995kt respectively. Chengdu, the provincial capital city, had the largest emission load of every pollutant among the cities. The industry sources, including power plants, fuel combustion facilities and non-combustion processes were the largest emission sources for SO2、NOX and CO, contributing to 84%, 46.5%, 35% of total SO2, NOX and CO emissions. On-road mobile sources accounted for 46.5%, 33%, 16% of the total NOx, CO, PM2.5 emissions and 28% of the anthropogenic VOCs emission. Dust and industry sources contributed to 42% and 23% of the PM10 emission with the dust sources also as the largest source of PM2.5, contributing to 27%. Anthropogenic and biogenic sources took 75% and 25% of the total VOCs emission while 36% of anthropogenic VOCs emission was owing to solvent use. Livestock contributed to 62% of NH3 emissions, followed by nitrogen fertilizer application whose contribution was 23%. Based on the developed emission inventory and local meteorological data, the regional air quality modeling system WRF-CMAQ was applied to simulate the status of PM2.5 pollution in a regional scale. The results showed that high PM2.5 concentration was distributed over the urban area of Chengdu and Deyang. On-road mobile sources and dust sources were two major contributors to the PM2.5 pollution in Chengdu, both had an contribution ratio of 27%. In Deyang, Mianyang, Meishan and Ziyang, industry sources had a relatively high contribution ratio to the PM2.5 pollution, accounting for about 35%, 33%, 38% and 24% respectively.

Changes in U.S. hardwood lumber exports, 1990 to 2008

Treesearch

William Luppold; Matthew Bumgardner

2011-01-01

The volume of hardwood lumber exported from the United States grew by 63 percent between 1990 and 2006 before decreasing by 29 percent between 2006 and 2008. Canada is both the largest export market for U.S. hardwood lumber and the largest source country for hardwood lumber imported into the United States. In the last 19 years China/Hong Kong has displaced Japan as the...

A pseudo-penalized quasi-likelihood approach to the spatial misalignment problem with non-normal data.

PubMed

Lopiano, Kenneth K; Young, Linda J; Gotway, Carol A

2014-09-01

Spatially referenced datasets arising from multiple sources are routinely combined to assess relationships among various outcomes and covariates. The geographical units associated with the data, such as the geographical coordinates or areal-level administrative units, are often spatially misaligned, that is, observed at different locations or aggregated over different geographical units. As a result, the covariate is often predicted at the locations where the response is observed. The method used to align disparate datasets must be accounted for when subsequently modeling the aligned data. Here we consider the case where kriging is used to align datasets in point-to-point and point-to-areal misalignment problems when the response variable is non-normally distributed. If the relationship is modeled using generalized linear models, the additional uncertainty induced from using the kriging mean as a covariate introduces a Berkson error structure. In this article, we develop a pseudo-penalized quasi-likelihood algorithm to account for the additional uncertainty when estimating regression parameters and associated measures of uncertainty. The method is applied to a point-to-point example assessing the relationship between low-birth weights and PM2.5 levels after the onset of the largest wildfire in Florida history, the Bugaboo scrub fire. A point-to-areal misalignment problem is presented where the relationship between asthma events in Florida's counties and PM2.5 levels after the onset of the fire is assessed. Finally, the method is evaluated using a simulation study. Our results indicate the method performs well in terms of coverage for 95% confidence intervals and naive methods that ignore the additional uncertainty tend to underestimate the variability associated with parameter estimates. The underestimation is most profound in Poisson regression models. © 2014, The International Biometric Society.

AMMONIA: ENVIRONMENTAL IMPACTS, EMISSIONS, INORGANIC PM 2.5, AND CLEAN AIR INTERSTATE RULE

EPA Science Inventory

This presentation discusses the role of ammonia as an atmospheric pollutant. Ammonia is emitted primarily from agricultural sources, although vehicles are the largest sources in urban centers. When combined with nitrate and sulfate, ammonia forms particulate matter which has be...

Environmental effects of large impacts on Mars.

PubMed

Segura, Teresa L; Toon, Owen B; Colaprete, Anthony; Zahnle, Kevin

2002-12-06

The martian valley networks formed near the end of the period of heavy bombardment of the inner solar system, about 3.5 billion years ago. The largest impacts produced global blankets of very hot ejecta, ranging in thickness from meters to hundreds of meters. Our simulations indicated that the ejecta warmed the surface, keeping it above the freezing point of water for periods ranging from decades to millennia, depending on impactor size, and caused shallow subsurface or polar ice to evaporate or melt. Large impacts also injected steam into the atmosphere from the craters or from water innate to the impactors. From all sources, a typical 100-, 200-, or 250-kilometers asteroid injected about 2, 9, or 16 meters, respectively, of precipitable water into the atmosphere, which eventually rained out at a rate of about 2 meters per year. The rains from a large impact formed rivers and contributed to recharging aquifers.

Clinical outcome of the metal-on-metal hybrid Corin Cormet 2000 hip resurfacing system: an up to 11-year follow-up study.

PubMed

Gross, Thomas P; Liu, Fei; Webb, Lee A

2012-04-01

This report extends the follow-up for the largest center of the first multicenter US Food and Drug Administration investigational device exemption study on metal-on-metal hip resurfacing arthroplasty up to 11 years. A single surgeon performed 373 hip resurfacing arthroplasties using the hybrid Corin Cormet 2000 system. The Kaplan-Meier survivorship at 11 years was 93% when revision for any reason was used as an end point and 91% if radiographic failures were included. The clinical results demonstrate an acceptable failure rate with use of this system. Loosening of the cemented femoral components was the most common source of failure and occurred at all follow-up intervals. A learning curve that persisted for at least 200 cases was confirmed. All femoral neck fractures occurred before 6 months postoperatively. Copyright © 2012 Elsevier Inc. All rights reserved.

Potential-field sounding using Euler's homogeneity equation and Zidarov bubbling

USGS Publications Warehouse

Cordell, Lindrith

1994-01-01

Potential-field (gravity) data are transformed into a physical-property (density) distribution in a lower half-space, constrained solely by assumed upper bounds on physical-property contrast and data error. A two-step process is involved. The data are first transformed to an equivalent set of line (2-D case) or point (3-D case) sources, using Euler's homogeneity equation evaluated iteratively on the largest residual data value. Then, mass is converted to a volume-density product, constrained to an upper density bound, by 'bubbling,' which exploits circular or radial expansion to redistribute density without changing the associated gravity field. The method can be developed for gravity or magnetic data in two or three dimensions. The results can provide a beginning for interpretation of potential-field data where few independent constraints exist, or more likely, can be used to develop models and confirm or extend interpretation of other geophysical data sets.

Earthquake stress via event ratio levels: Application to the 2011 and 2016 Oklahoma seismic sequences

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walter, William R.; Yoo, Seung -Hoon; Mayeda, Kevin

Here, we develop a new methodology for determining earthquake stress drop and apparent stress values via spectral ratio asymptotic levels. With sufficient bandwidth, the stress ratio for a pair of events can be directly related to these low- and high-frequency levels. This avoids the need to assume a particular spectral model and derive stress drop from cubed corner frequency measures. The method can be applied to spectral ratios for any pair of closely related earthquakes and is particularly well suited for coda envelope methods that provide good azimuthally averaged, point-source measures. We apply the new method to the 2011 Praguemore » and 2016 Pawnee earthquake sequences in Oklahoma. The sequences show stress scaling with size and depth, with the largest events having apparent stress levels near 1 MPa and smaller and/or shallower events having systematically lower stress values.« less

Earthquake stress via event ratio levels: Application to the 2011 and 2016 Oklahoma seismic sequences

DOE PAGES

Walter, William R.; Yoo, Seung -Hoon; Mayeda, Kevin; ...

2017-04-03

Here, we develop a new methodology for determining earthquake stress drop and apparent stress values via spectral ratio asymptotic levels. With sufficient bandwidth, the stress ratio for a pair of events can be directly related to these low- and high-frequency levels. This avoids the need to assume a particular spectral model and derive stress drop from cubed corner frequency measures. The method can be applied to spectral ratios for any pair of closely related earthquakes and is particularly well suited for coda envelope methods that provide good azimuthally averaged, point-source measures. We apply the new method to the 2011 Praguemore » and 2016 Pawnee earthquake sequences in Oklahoma. The sequences show stress scaling with size and depth, with the largest events having apparent stress levels near 1 MPa and smaller and/or shallower events having systematically lower stress values.« less

Performance evaluation of a direct-conversion flat-panel detector system in imaging and quality assurance for a high-dose-rate 192Ir source

NASA Astrophysics Data System (ADS)

Miyahara, Yoshinori; Hara, Yuki; Nakashima, Hiroto; Nishimura, Tomonori; Itakura, Kanae; Inomata, Taisuke; Kitagaki, Hajime

2018-03-01

In high-dose-rate (HDR) brachytherapy, a direct-conversion flat-panel detector (d-FPD) clearly depicts a 192Ir source without image halation, even under the emission of high-energy gamma rays. However, it was unknown why iridium is visible when using a d-FPD. The purpose of this study was to clarify the reasons for visibility of the source core based on physical imaging characteristics, including the modulation transfer functions (MTF), noise power spectral (NPS), contrast transfer functions, and linearity of d-FPD to high-energy gamma rays. The acquired data included: x-rays, [X]; gamma rays, [γ] dual rays (X  +  γ), [D], and subtracted data for depicting the source ([D]  -  [γ]). In the quality assurance (QA) test for the positional accuracy of a source core, the coordinates of each dwelling point were compared between the planned and actual source core positions using a CT/MR-compatible ovoid applicator and a Fletcher-Williamson applicator. The profile curves of [X] and ([D]  -  [γ]) matched well on MTF and NPS. The contrast resolutions of [D] and [X] were equivalent. A strongly positive linear correlation was found between the output data of [γ] and source strength (r 2  >  0.99). With regard to the accuracy of the source core position, the largest coordinate difference (3D distance) was noted at the maximum curvature of the CT/MR-compatible ovoid and Fletcher-Williamson applicators, showing 1.74  ±  0.02 mm and 1.01  ±  0.01 mm, respectively. A d-FPD system provides high-quality images of a source, even when high-energy gamma rays are emitted to the detector, and positional accuracy tests with clinical applicators are useful in identifying source positions (source movements) within the applicator for QA.

Key composition optimization of meat processed protein source by vacuum freeze-drying technology.

PubMed

Ma, Yan; Wu, Xingzhuang; Zhang, Qi; Giovanni, Vigna; Meng, Xianjun

2018-05-01

Vacuum freeze-drying technology is a high technology content, a wide range of knowledge of technology in the field of drying technology is involved, it is also a method of the most complex drying equipment, the largest energy consumption, the highest cost of drying method, but due to the particularity of its dry goods: the freeze-drying food has the advantages of complex water performance is good, cooler and luster of freezing and drying food to maintain good products, less nutrient loss, light weight, easy to carry transportation, easy to long-term preservation, and on the quality is far superior to the obvious advantages of other dried food, making it become the forefront of drying technology research and development. The freeze-drying process of Chinese style ham and western Germany fruit tree tenderloin is studied in this paper, their eutectic point, melting point and collapse temperature, freeze-drying curve and its heat and mass transfer characteristics are got, then the precool temperature and the highest limiting temperature of sublimation interface are determined. The effect of system pressure on freeze-dried rate in freeze-drying process is discussed, and the method of regulating pressure circularly is determined.

Estimated withdrawals and use of freshwater in New Hampshire, 1990

USGS Publications Warehouse

Medalie, Laura; Horn, M.A.

1994-01-01

Estimated freshwater withdrawals during 1990 in New Hampshire totaled about 422 million gallons per day from ground-water and surface-water sources. The largest withdrawals were for thermoelectric-power generation (60 percent), public supply (23 percent), and industrial use (9 percent). Most withdrawals, 358 million gallons per day, were made from surface- water sources, as compared to 63.7 million gallons per day from ground-water sources. The largest with- drawals were in the Merrimack river basin (322 million gallons per day). An additional 46,000 million gallons per day was used instream for hydroelectric-power generation, primarily in the Upper Androscoggin and Upper Connecticut River subbasins. Other information describing water-use patterns is shown in tables, bar graphs, pie charts, maps, and accompanying text. The data are aggregated by river basin (hydrologic cataloging unit), and all values are reported in million gallons per day.

Dynamic Stocks and Flows Analysis of Bisphenol A (BPA) in China: 2000-2014.

PubMed

Jiang, Daqian; Chen, Wei-Qiang; Zeng, Xianlai; Tang, Linbin

2018-03-20

Bisphenol A (BPA), a synthetic organic chemical, is creating a new category of ecological and human health challenges due to unintended leakage. Effectively managing the use and leakage of BPA can benefit from an understanding of the anthropogenic BPA cycles (i.e., the size of BPA flows and stocks). In this work, we provide a dynamic analysis of the anthropogenic BPA cycles in China for 2000-2014. We find that China's BPA consumption has increased 10-fold since 2000, to ∼3 million tonnes/year. With the increasing consumption, China's in-use BPA stock has increased 500-fold to 14.0 million tonnes (i.e., 10.2 kg BPA/capita). It is unclear whether a saturation point has been reached, but in 2004-2014, China's in-use BPA stock has been increasing by 0.8 kg BPA/capita annually. Electronic products are the biggest contributor, responsible for roughly one-third of China's in-use BPA stock. Optical media (DVD/VCD/CDs) is the largest contributor to China's current End-of-Life (EoL) BPA flow, totaling 0.9 million tonnes/year. However, the EoL BPA flow due to e-waste will increase quickly, and will soon become the largest EoL BPA flow. The changing quantities and sources of EoL BPA flows may require a shift in the macroscopic BPA management strategies.

Stable Carbon Fractionation In Size Segregated Aerosol Particles Produced By Controlled Biomass Burning

NASA Astrophysics Data System (ADS)

Masalaite, Agne; Garbaras, Andrius; Garbariene, Inga; Ceburnis, Darius; Martuzevicius, Dainius; Puida, Egidijus; Kvietkus, Kestutis; Remeikis, Vidmantas

2014-05-01

Biomass burning is the largest source of primary fine fraction carbonaceous particles and the second largest source of trace gases in the global atmosphere with a strong effect not only on the regional scale but also in areas distant from the source . Many studies have often assumed no significant carbon isotope fractionation occurring between black carbon and the original vegetation during combustion. However, other studies suggested that stable carbon isotope ratios of char or BC may not reliably reflect carbon isotopic signatures of the source vegetation. Overall, the apparently conflicting results throughout the literature regarding the observed fractionation suggest that combustion conditions may be responsible for the observed effects. The purpose of the present study was to gather more quantitative information on carbonaceous aerosols produced in controlled biomass burning, thereby having a potential impact on interpreting ambient atmospheric observations. Seven different biomass fuel types were burned under controlled conditions to determine the effect of the biomass type on the emitted particulate matter mass and stable carbon isotope composition of bulk and size segregated particles. Size segregated aerosol particles were collected using the total suspended particle (TSP) sampler and a micro-orifice uniform deposit impactor (MOUDI). The results demonstrated that particle emissions were dominated by the submicron particles in all biomass types. However, significant differences in emissions of submicron particles and their dominant sizes were found between different biomass fuels. The largest negative fractionation was obtained for the wood pellet fuel type while the largest positive isotopic fractionation was observed during the buckwheat shells combustion. The carbon isotope composition of MOUDI samples compared very well with isotope composition of TSP samples indicating consistency of the results. The measurements of the stable carbon isotope ratio in size segregated aerosol particles suggested that combustion processes could strongly affect isotopic fractionation in aerosol particles of different sizes thereby potentially affecting an interpretation of ambient atmospheric observations.

76 FR 74832 - Entergy Nuclear Indian Point Unit 2, LLC; Entergy Nuclear Indian Point Unit 3, LLC; Entergy...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-01

... hot shutdown for fire areas in which both trains of safe-shutdown cables or equipment are located in... proposed action. The staff has concluded that such actions would not adversely affect the environment. The... case. This exemption request will not have a significant effect on the environment, as the largest...

Diagnostic Air Quality Model Evaluation of Source-Specific ...

EPA Pesticide Factsheets

Ambient measurements of 78 source-specific tracers of primary and secondary carbonaceous fine particulate matter collected at four midwestern United States locations over a full year (March 2004–February 2005) provided an unprecedented opportunity to diagnostically evaluate the results of a numerical air quality model. Previous analyses of these measurements demonstrated excellent mass closure for the variety of contributing sources. In this study, a carbon-apportionment version of the Community Multiscale Air Quality (CMAQ) model was used to track primary organic and elemental carbon emissions from 15 independent sources such as mobile sources and biomass burning in addition to four precursor-specific classes of secondary organic aerosol (SOA) originating from isoprene, terpenes, aromatics, and sesquiterpenes. Conversion of the source-resolved model output into organic tracer concentrations yielded a total of 2416 data pairs for comparison with observations. While emission source contributions to the total model bias varied by season and measurement location, the largest absolute bias of −0.55 μgC/m3 was attributed to insufficient isoprene SOA in the summertime CMAQ simulation. Biomass combustion was responsible for the second largest summertime model bias (−0.46 μgC/m3 on average). Several instances of compensating errors were also evident; model underpredictions in some sectors were masked by overpredictions in others. The National Exposure Research L

Diagnostic air quality model evaluation of source-specific primary and secondary fine particulate carbon.

PubMed

Napelenok, Sergey L; Simon, Heather; Bhave, Prakash V; Pye, Havala O T; Pouliot, George A; Sheesley, Rebecca J; Schauer, James J

2014-01-01

Ambient measurements of 78 source-specific tracers of primary and secondary carbonaceous fine particulate matter collected at four midwestern United States locations over a full year (March 2004-February 2005) provided an unprecedented opportunity to diagnostically evaluate the results of a numerical air quality model. Previous analyses of these measurements demonstrated excellent mass closure for the variety of contributing sources. In this study, a carbon-apportionment version of the Community Multiscale Air Quality (CMAQ) model was used to track primary organic and elemental carbon emissions from 15 independent sources such as mobile sources and biomass burning in addition to four precursor-specific classes of secondary organic aerosol (SOA) originating from isoprene, terpenes, aromatics, and sesquiterpenes. Conversion of the source-resolved model output into organic tracer concentrations yielded a total of 2416 data pairs for comparison with observations. While emission source contributions to the total model bias varied by season and measurement location, the largest absolute bias of -0.55 μgC/m(3) was attributed to insufficient isoprene SOA in the summertime CMAQ simulation. Biomass combustion was responsible for the second largest summertime model bias (-0.46 μgC/m(3) on average). Several instances of compensating errors were also evident; model underpredictions in some sectors were masked by overpredictions in others.

[A landscape ecological approach for urban non-point source pollution control].

PubMed

Guo, Qinghai; Ma, Keming; Zhao, Jingzhu; Yang, Liu; Yin, Chengqing

2005-05-01

Urban non-point source pollution is a new problem appeared with the speeding development of urbanization. The particularity of urban land use and the increase of impervious surface area make urban non-point source pollution differ from agricultural non-point source pollution, and more difficult to control. Best Management Practices (BMPs) are the effective practices commonly applied in controlling urban non-point source pollution, mainly adopting local repairing practices to control the pollutants in surface runoff. Because of the close relationship between urban land use patterns and non-point source pollution, it would be rational to combine the landscape ecological planning with local BMPs to control the urban non-point source pollution, which needs, firstly, analyzing and evaluating the influence of landscape structure on water-bodies, pollution sources and pollutant removal processes to define the relationships between landscape spatial pattern and non-point source pollution and to decide the key polluted fields, and secondly, adjusting inherent landscape structures or/and joining new landscape factors to form new landscape pattern, and combining landscape planning and management through applying BMPs into planning to improve urban landscape heterogeneity and to control urban non-point source pollution.

The violent environment of the origin of life - Progress and uncertainties

NASA Technical Reports Server (NTRS)

Chyba, Christopher F.

1993-01-01

Dating of terrestrial fossils and returned lunar samples reveals that the origin of life on Earth occurred not in a quiescent, peaceful environment, but rather in a violent, impact-ridden one. This realization has important consequences. On the one hand, sufficiently large and fast impactors can erode planetary atmospheres, and the very largest of these may have sterilized the surface of the Earth. In this regard, deep-sea hydrothermal vents become especially interesting for the history of early life, as they provide an environment protected against all but the greatest impact devastation. At the same time, impactors would have been delivering key biogenic elements (such as carbon and nitrogen) to Earth's surface, and (with much greater difficulty) intact organic molecules as well. Estimates of the various sources of prebiotic organics suggest that the heavy bombardment either produced or delivered quantities of organics comparable to those produced by other energy sources. However, substantial uncertainties exist. After reviewing the current understanding of the role of the heavy bombardment in the origins of life, a number of remaining key uncertainties are considered, and attempts are made to both quantify their magnitude and point to means of resolving them.

Optimizing the scale of markets for water quality trading

NASA Astrophysics Data System (ADS)

Doyle, Martin W.; Patterson, Lauren A.; Chen, Yanyou; Schnier, Kurt E.; Yates, Andrew J.

2014-09-01

Applying market approaches to environmental regulations requires establishing a spatial scale for trading. Spatially large markets usually increase opportunities for abatement cost savings but increase the potential for pollution damages (hot spots), vice versa for spatially small markets. We develop a coupled hydrologic-economic modeling approach for application to point source emissions trading by a large number of sources and apply this approach to the wastewater treatment plants (WWTPs) within the watershed of the second largest estuary in the U.S. We consider two different administrative structures that govern the trade of emission permits: one-for-one trading (the number of permits required for each unit of emission is the same for every WWTP) and trading ratios (the number of permits required for each unit of emissions varies across WWTP). Results show that water quality regulators should allow trading to occur at the river basin scale as an appropriate first-step policy, as is being done in a limited number of cases via compliance associations. Larger spatial scales may be needed under conditions of increased abatement costs. The optimal scale of the market is generally the same regardless of whether one-for-one trading or trading ratios are employed.

In Search of the Largest Possible Tsunami: An Example Following the 2011 Japan Tsunami

NASA Astrophysics Data System (ADS)

Geist, E. L.; Parsons, T.

2012-12-01

Many tsunami hazard assessments focus on estimating the largest possible tsunami: i.e., the worst-case scenario. This is typically performed by examining historic and prehistoric tsunami data or by estimating the largest source that can produce a tsunami. We demonstrate that worst-case assessments derived from tsunami and tsunami-source catalogs are greatly affected by sampling bias. Both tsunami and tsunami sources are well represented by a Pareto distribution. It is intuitive to assume that there is some limiting size (i.e., runup or seismic moment) for which a Pareto distribution is truncated or tapered. Likelihood methods are used to determine whether a limiting size can be determined from existing catalogs. Results from synthetic catalogs indicate that several observations near the limiting size are needed for accurate parameter estimation. Accordingly, the catalog length needed to empirically determine the limiting size is dependent on the difference between the limiting size and the observation threshold, with larger catalog lengths needed for larger limiting-threshold size differences. Most, if not all, tsunami catalogs and regional tsunami source catalogs are of insufficient length to determine the upper bound on tsunami runup. As an example, estimates of the empirical tsunami runup distribution are obtained from the Miyako tide gauge station in Japan, which recorded the 2011 Tohoku-oki tsunami as the largest tsunami among 51 other events. Parameter estimation using a tapered Pareto distribution is made both with and without the Tohoku-oki event. The catalog without the 2011 event appears to have a low limiting tsunami runup. However, this is an artifact of undersampling. Including the 2011 event, the catalog conforms more to a pure Pareto distribution with no confidence in estimating a limiting runup. Estimating the size distribution of regional tsunami sources is subject to the same sampling bias. Physical attenuation mechanisms such as wave breaking likely limit the maximum tsunami runup at a particular site. However, historic and prehistoric data alone cannot determine the upper bound on tsunami runup. Because of problems endemic to sampling Pareto distributions of tsunamis and their sources, we recommend that tsunami hazard assessment be based on a specific design probability of exceedance following a pure Pareto distribution, rather than attempting to determine the worst-case scenario.

Impacts of manure application on SWAT model outputs in the Xiangxi River watershed

NASA Astrophysics Data System (ADS)

Liu, Ruimin; Wang, Qingrui; Xu, Fei; Men, Cong; Guo, Lijia

2017-12-01

SWAT (Soil and Water Assessment Tool) model has been widely used to simulate agricultural non-point source (ANPS) pollution; however, the impacts of livestock manure application on SWAT model outputs have not been well studied. The objective of this study was to investigate the environmental effects of livestock manure application based on the SWAT model in the Xiangxi River watershed, which is one of the largest tributaries of the Three Gorges Reservoir in China. Three newly-built manure databases (NB) were created and applied to different subbasins based on the actual livestock manure discharging amount. The calibration and validation values of SWAT model outputs obtained from the NB manure application and the original mixed (OM) manure were compared. The study results are as follows: (1) The livestock industry of Xingshan County developed quickly between 2005 and 2015. The downstream of the Xiangxi River (Huangliang, Shuiyuesi and Xiakou) had the largest livestock amount, and largely accounted for manure, total nitrogen (TN) and total phosphorus (TP) production (>50%). (2) The NB manure application resulted in less phosphorus pollution (1686.35 kg for ORGP and 31.70 kg for MINP) than the OM manure application. Compared with the upstream, the downstream was influenced more by the manure application. (3) The SWAT results obtained from the NB manure had a better calibration and validation values than those from the OM manure. For ORGP, R2 and NSE values were 0.77 and 0.65 for the NB manure calibration; and the same values for the OM manure were 0.72 and 0.61, respectively. For MINP, R2 values were 0.65 and 0.62 for the NB manure and the OM manure, and the NSE values were 0.60 and 0.58, respectively. The results indicated that the built-in fertilizer database in SWAT has its limitation because it is set up for the simulation in the USA. Thus, when livestock manure is considered in a SWAT simulation, a newly built fertilizer database needs to be set up to represent the localized condition more accurately. The conclusions of this study would be instructive for livestock pollution simulations, and favorable for non-point source pollution prevention at the watershed scale.

Common Cents? The Role of Pennies in the U.S. Economy

DTIC Science & Technology

2006-12-01

economy. This debate stems from political and economical sources with ties to historical references. This paper explores the various reasons for...roughly $.50. Today, that same pound of zinc costs nearly $1.50.14 Additionally, China is currently experiencing an economic whirlwind. The... economic growth in China has turned it from one of the world’s largest zinc exporters to one of the largest zinc importers.15 As a result, many items

Economic analysis of electronic waste recycling: modeling the cost and revenue of a materials recovery facility in California.

PubMed

Kang, Hai-Yong; Schoenung, Julie M

2006-03-01

The objectives of this study are to identify the various techniques used for treating electronic waste (e-waste) at material recovery facilities (MRFs) in the state of California and to investigate the costs and revenue drivers for these techniques. The economics of a representative e-waste MRF are evaluated by using technical cost modeling (TCM). MRFs are a critical element in the infrastructure being developed within the e-waste recycling industry. At an MRF, collected e-waste can become marketable output products including resalable systems/components and recyclable materials such as plastics, metals, and glass. TCM has two main constituents, inputs and outputs. Inputs are process-related and economic variables, which are directly specified in each model. Inputs can be divided into two parts: inputs for cost estimation and for revenue estimation. Outputs are the results of modeling and consist of costs and revenues, distributed by unit operation, cost element, and revenue source. The results of the present analysis indicate that the largest cost driver for the operation of the defined California e-waste MRF is the materials cost (37% of total cost), which includes the cost to outsource the recycling of the cathode ray tubes (CRTs) (dollar 0.33/kg); the second largest cost driver is labor cost (28% of total cost without accounting for overhead). The other cost drivers are transportation, building, and equipment costs. The most costly unit operation is cathode ray tube glass recycling, and the next are sorting, collecting, and dismantling. The largest revenue source is the fee charged to the customer; metal recovery is the second largest revenue source.

Application of largest Lyapunov exponent analysis on the studies of dynamics under external forces

NASA Astrophysics Data System (ADS)

Odavić, Jovan; Mali, Petar; Tekić, Jasmina; Pantić, Milan; Pavkov-Hrvojević, Milica

2017-06-01

Dynamics of driven dissipative Frenkel-Kontorova model is examined by using largest Lyapunov exponent computational technique. Obtained results show that besides the usual way where behavior of the system in the presence of external forces is studied by analyzing its dynamical response function, the largest Lyapunov exponent analysis can represent a very convenient tool to examine system dynamics. In the dc driven systems, the critical depinning force for particular structure could be estimated by computing the largest Lyapunov exponent. In the dc+ac driven systems, if the substrate potential is the standard sinusoidal one, calculation of the largest Lyapunov exponent offers a more sensitive way to detect the presence of Shapiro steps. When the amplitude of the ac force is varied the behavior of the largest Lyapunov exponent in the pinned regime completely reflects the behavior of Shapiro steps and the critical depinning force, in particular, it represents the mirror image of the amplitude dependence of critical depinning force. This points out an advantage of this technique since by calculating the largest Lyapunov exponent in the pinned regime we can get an insight into the dynamics of the system when driving forces are applied. Additionally, the system is shown to be not chaotic even in the case of incommensurate structures and large amplitudes of external force, which is a consequence of overdampness of the model and the Middleton's no passing rule.

Evaluation of total phosphorus mass balance in the lower Boise River and selected tributaries, southwestern Idaho

USGS Publications Warehouse

Etheridge, Alexandra B.

2013-01-01

he U.S. Geological Survey (USGS), in cooperation with Idaho Department of Environmental Quality, developed spreadsheet mass-balance models for total phosphorus using results from three synoptic sampling periods conducted in the lower Boise River watershed during August and October 2012, and March 2013. The modeling reach spanned 46.4 river miles (RM) along the Boise River from Veteran’s Memorial Parkway in Boise, Idaho (RM 50.2), to Parma, Idaho (RM 3.8). The USGS collected water-quality samples and measured streamflow at 14 main-stem Boise River sites, two Boise River north channel sites, two sites on the Snake River upstream and downstream of its confluence with the Boise River, and 17 tributary and return-flow sites. Additional samples were collected from treated effluent at six wastewater treatment plants and two fish hatcheries. The Idaho Department of Water Resources quantified diversion flows in the modeling reach. Total phosphorus mass-balance models were useful tools for evaluating sources of phosphorus in the Boise River during each sampling period. The timing of synoptic sampling allowed the USGS to evaluate phosphorus inputs to and outputs from the Boise River during irrigation season, shortly after irrigation ended, and soon before irrigation resumed. Results from the synoptic sampling periods showed important differences in surface-water and groundwater distribution and phosphorus loading. In late August 2012, substantial streamflow gains to the Boise River occurred from Middleton (RM 31.4) downstream to Parma (RM 3.8). Mass-balance model results indicated that point and nonpoint sources (including groundwater) contributed phosphorus loads to the Boise River during irrigation season. Groundwater exchange within the Boise River in October 2012 and March 2013 was not as considerable as that measured in August 2012. However, groundwater discharge to agricultural tributaries and drains during non-irrigation season was a large source of discharge and phosphorus in the lower Boise River in October 2012 and March 2013. Model results indicate that point sources represent the largest contribution of phosphorus to the Boise River year round, but that reductions in point and nonpoint source phosphorus loads may be necessary to achieve seasonal total phosphorus concentration targets at Parma (RM 3.8) from May 1 through September 30, as set by the 2004 Snake River-Hells Canyon Total Maximum Daily Load document. The mass-balance models do not account for biological or depositional instream processes, but are useful indicators of locations where appreciable phosphorus uptake or release by aquatic plants may occur.

Digital Bedrock Compilation: A Geodatabase Covering Forest Service Lands in California

NASA Astrophysics Data System (ADS)

Elder, D.; de La Fuente, J. A.; Reichert, M.

2010-12-01

This digital database contains bedrock geologic mapping for Forest Service lands within California. This compilation began in 2004 and the first version was completed in 2005. Second publication of this geodatabase was completed in 2010 and filled major gaps in the southern Sierra Nevada and Modoc/Medicine Lake/Warner Mountains areas. This digital map database was compiled from previously published and unpublished geologic mapping, with source mapping and review from California Geological Survey, the U.S. Geological Survey and others. Much of the source data was itself compilation mapping. This geodatabase is huge, containing ~107,000 polygons and ~ 280,000 arcs. Mapping was compiled from more than one thousand individual sources and covers over 41,000,000 acres (~166,000 km2). It was compiled from source maps at various scales - from ~ 1:4,000 to 1:250,000 and represents the best available geologic mapping at largest scale possible. An estimated 70-80% of the source information was digitized from geologic mapping at 1:62,500 scale or better. Forest Service ACT2 Enterprise Team compiled the bedrock mapping and developed a geodatabase to store this information. This geodatabase supports feature classes for polygons (e.g, map units), lines (e.g., contacts, boundaries, faults and structural lines) and points (e.g., orientation data, structural symbology). Lookup tables provide detailed information for feature class items. Lookup/type tables contain legal values and hierarchical groupings for geologic ages and lithologies. Type tables link coded values with descriptions for line and point attributes, such as line type, line location and point type. This digital mapping is at the core of many quantitative analyses and derivative map products. Queries of the database are used to produce maps and to quantify rock types of interest. These include the following: (1) ultramafic rocks - where hazards from naturally occurring asbestos are high, (2) granitic rocks - increased erosion hazards, (3) limestone, chert, sedimentary rocks - paleontological resources (Potential Fossil Yield Classification maps), (4) calcareous rocks (cave resources, water chemistry), and (5) lava flows - lava tubes (more caves). Map unit groupings (e.g., belts, terranes, tectonic & geomorphic provinces) can also be derived from the geodatabase. Digital geologic mapping was used in ground water modeling to predict effects of tunneling through the San Bernardino Mountains. Bedrock mapping is used in models that characterize watershed sediment regimes and quantify anthropogenic influences. When combined with digital geomorphology mapping, this geodatabase helps to assess landslide hazards.

Jovian System as a Demonstration of JWST’s Capabilities for Solar System Science: Status Update

NASA Astrophysics Data System (ADS)

Conrad, Al; Fouchet, Thierry

2018-06-01

Characterize Jupiter’s cloud layers, winds, composition, auroral activity, and temperature structureProduce maps of the atmosphere and surface of volcanically-active Io and icy satellite Ganymede to constrain their thermal and atmospheric structure, and search for plumesCharacterize the ring structure, and its sources, sinks and evolution.We will present our progress to date in planning these observations and provide an update on our expectations.Our program will utilize all JWST instruments in different observing modes to demonstrate the capabilities of JWST’s instruments on one of the largest and brightest sources in the Solar System and on very faint targets next to it. We will also observe weak emission/absorption bands on strong continua, and with NIRIS/AMI we will maximize the Strehl ratio on unresolved features, such as Io’s volcanoes.We will deliver a number of science enabling products that will facilitate community science, including, e.g.: i) characterizing Jupiter’s scattered light in the context of scientific observations, ii) resolve point sources with AMI in a crowded field (Io’s volcanoes), and compare this to classical observations, iii) develop tools to mosaic/visualize spectral datacubes using MIRI and NIRSpec on Jupiter. Finally, our program will also set a first temporal benchmark to study time variations in the jovian system and any interconnectivity (e.g., through its magnetic field) during JWST’s lifetime.

Selectivity of physiotherapist programs in the United States does not differ by institutional funding source or research activity level.

PubMed

Riley, Sean P; Covington, Kyle; Landry, Michel D; McCallum, Christine; Engelhard, Chalee; Cook, Chad E

2016-01-01

This study aimed to compare selectivity characteristics among institution characteristics to determine differences by institutional funding source (public vs. private) or research activity level (research vs. non-research). This study included information provided by the Commission on Accreditation in Physical Therapy Education (CAPTE) and the Federation of State Boards of Physical Therapy. Data were extracted from all students who graduated in 2011 from accredited physical therapy programs in the United States. The public and private designations of the institutions were extracted directly from the classifications from the 'CAPTE annual accreditation report,' and high and low research activity was determined based on Carnegie classifications. The institutions were classified into four groups: public/research intensive, public/non-research intensive, private/research intensive, and private/non-research intensive. Descriptive and comparison analyses with post hoc testing were performed to determine whether there were statistically significant differences among the four groups. Although there were statistically significant baseline grade point average differences among the four categorized groups, there were no significant differences in licensure pass rates or for any of the selectivity variables of interest. Selectivity characteristics did not differ by institutional funding source (public vs. private) or research activity level (research vs. non-research). This suggests that the concerns about reduced selectivity among physiotherapy programs, specifically the types that are experiencing the largest proliferation, appear less warranted.

Inferring Models of Bacterial Dynamics toward Point Sources

PubMed Central

Jashnsaz, Hossein; Nguyen, Tyler; Petrache, Horia I.; Pressé, Steve

2015-01-01

Experiments have shown that bacteria can be sensitive to small variations in chemoattractant (CA) concentrations. Motivated by these findings, our focus here is on a regime rarely studied in experiments: bacteria tracking point CA sources (such as food patches or even prey). In tracking point sources, the CA detected by bacteria may show very large spatiotemporal fluctuations which vary with distance from the source. We present a general statistical model to describe how bacteria locate point sources of food on the basis of stochastic event detection, rather than CA gradient information. We show how all model parameters can be directly inferred from single cell tracking data even in the limit of high detection noise. Once parameterized, our model recapitulates bacterial behavior around point sources such as the “volcano effect”. In addition, while the search by bacteria for point sources such as prey may appear random, our model identifies key statistical signatures of a targeted search for a point source given any arbitrary source configuration. PMID:26466373

A Method for Identifying Pollution Sources of Heavy Metals and PAH for a Risk-Based Management of a Mediterranean Harbour

PubMed Central

Moranda, Arianna

2017-01-01

A procedure for assessing harbour pollution by heavy metals and PAH and the possible sources of contamination is proposed. The procedure is based on a ratio-matching method applied to the results of principal component analysis (PCA), and it allows discrimination between point and nonpoint sources. The approach can be adopted when many sources of pollution can contribute in a very narrow coastal ecosystem, both internal and outside but close to the harbour, and was used to identify the possible point sources of contamination in a Mediterranean Harbour (Port of Vado, Savona, Italy). 235 sediment samples were collected in 81 sampling points during four monitoring campaigns and 28 chemicals were searched for within the collected samples. PCA of total samples allowed the assessment of 8 main possible point sources, while the refining ratio-matching identified 1 sampling point as a possible PAH source, 2 sampling points as Cd point sources, and 3 sampling points as C > 12 point sources. By a map analysis it was possible to assess two internal sources of pollution directly related to terminals activity. The study is the prosecution of a previous work aimed at assessing Savona-Vado Harbour pollution levels and suggested strategies to regulate the harbour activities. PMID:29270328

A Method for Identifying Pollution Sources of Heavy Metals and PAH for a Risk-Based Management of a Mediterranean Harbour.

PubMed

Paladino, Ombretta; Moranda, Arianna; Seyedsalehi, Mahdi

2017-01-01

A procedure for assessing harbour pollution by heavy metals and PAH and the possible sources of contamination is proposed. The procedure is based on a ratio-matching method applied to the results of principal component analysis (PCA), and it allows discrimination between point and nonpoint sources. The approach can be adopted when many sources of pollution can contribute in a very narrow coastal ecosystem, both internal and outside but close to the harbour, and was used to identify the possible point sources of contamination in a Mediterranean Harbour (Port of Vado, Savona, Italy). 235 sediment samples were collected in 81 sampling points during four monitoring campaigns and 28 chemicals were searched for within the collected samples. PCA of total samples allowed the assessment of 8 main possible point sources, while the refining ratio-matching identified 1 sampling point as a possible PAH source, 2 sampling points as Cd point sources, and 3 sampling points as C > 12 point sources. By a map analysis it was possible to assess two internal sources of pollution directly related to terminals activity. The study is the prosecution of a previous work aimed at assessing Savona-Vado Harbour pollution levels and suggested strategies to regulate the harbour activities.

Formaldehyde Source Attribution in Houston during TexAQS II and TRAMP

NASA Astrophysics Data System (ADS)

Guven, B.; Olaguer, E. P.

2010-12-01

To determine the relative importance of primary vs secondary formaldehyde in Houston, source apportionment was performed on continuous online measurements of VOCs, formaldehyde (HCHO), CO, SO2, and HONO at one urban and two industrial sites. The results of source apportionment were used in conjunction with the meteorological, emission inventory, emission event, and back trajectory data catalogued in Air Research Information Infrastructure (ARII) to determine the dominant source regions and evaluate the accuracy of reported regular and upset emissions from industrial facilities. The contribution of industrial sources such as flares from petrochemical plants and refineries to total atmospheric formaldehyde concentrations at the urban site is estimated to be 17% compared to 23% for mobile sources, amounting to 40% for the total contribution of primary HCHO sources. The relative contribution of industrial sources to HCHO concentration at the urban site increased to about 66% on some mornings coinciding with the HCHO peak concentrations. Secondary formation of HCHO during the day and night resulted from the reactions of industrial olefins and other VOCs with OH or ozone was a significant contributor to HCHO concentrations at the urban site. An analysis of emission event, back trajectory and ambient concentration data in ARII showed that a large percentage of emission events were associated with trajectories that passed through the two industrial sites when peaks in concentrations were detected at those sites. Some peak HCHO concentrations can also be linked to emission events of other VOCs, while a significant portion remained unexplained by the reported events. It is likely, based on the results from the SHARP campaign and our analysis, that some episodic emission events containing HCHO are unreported to the TCEQ. Overlaid CPF plots for nighttime (green) and daytime (red) HCHO concentrations measured at three sites and the locations of the largest emitting point sources around the sites. Average contributions to formaldehyde concentrations.

A protozoal-associated epizootic impacting marine wildlife: Mass-mortality of southern sea otters (Enhydra lutris nereis) due to Sarcocystis neurona infection

PubMed Central

Conrad, Patricia A.; Harris, Michael; Hatfield, Brian; Langlois, Gregg; Jessup, David A.; Magargal, Spencer L.; Packham, Andrea E.; Toy-Choutka, Sharon; Melli, Ann C.; Murray, Michael A.; Gulland, Frances M.; Grigg, Michael E.

2016-01-01

During April, 2004, 40 sick and dead southern sea otters (Enhydra lutris nereis) were recovered over 18 km of coastline near Morro Bay, California. This event represented the single largest monthly spike in mortality ever recorded during 30 years of southern sea otter stranding data collection. Because of the point-source nature of the event and clinical signs consistent with severe, acute neurological disease, exposure to a chemical or marine toxin was initially considered. However, detailed postmortem examinations revealed lesions consistent with an infectious etiology, and further investigation confirmed the protozoan parasite Sarcocystis neurona as the underlying cause. Tissues from 94% of examined otters were PCR-positive for S. neurona, based on DNA amplification and sequencing at the ITS-1 locus, and 100% of tested animals (n = 14) had elevated IgM and IgG titers to S. neurona. Evidence to support the point-source character of this event include the striking spatial and temporal clustering of cases and detection of high concentrations of anti-S. neurona IgM in serum of stranded animals. Concurrent exposure to the marine biotoxin domoic acid may have enhanced susceptibility of affected otters to S. neurona and exacerbated the neurological signs exhibited by stranded animals. Other factors that may have contributed to the severity of this epizootic include a large rainstorm that preceded the event and an abundance of razor clams near local beaches, attracting numerous otters close to shore within the affected area. This is the first report of a localized epizootic in marine wildlife caused by apicomplexan protozoa. PMID:20615616

A protozoal-associated epizootic impacting marine wildlife: mass-mortality of southern sea otters (Enhydra lutris nereis) due to Sarcocystis neurona infection.

PubMed

Miller, Melissa A; Conrad, Patricia A; Harris, Michael; Hatfield, Brian; Langlois, Gregg; Jessup, David A; Magargal, Spencer L; Packham, Andrea E; Toy-Choutka, Sharon; Melli, Ann C; Murray, Michael A; Gulland, Frances M; Grigg, Michael E

2010-09-20

During April 2004, 40 sick and dead southern sea otters (Enhydra lutris nereis) were recovered over 18km of coastline near Morro Bay, California. This event represented the single largest monthly spike in mortality ever recorded during 30 years of southern sea otter stranding data collection. Because of the point-source nature of the event and clinical signs consistent with severe, acute neurological disease, exposure to a chemical or marine toxin was initially considered. However, detailed postmortem examinations revealed lesions consistent with an infectious etiology, and further investigation confirmed the protozoan parasite Sarcocystis neurona as the underlying cause. Tissues from 94% of examined otters were PCR-positive for S. neurona, based on DNA amplification and sequencing at the ITS-1 locus, and 100% of tested animals (n=14) had elevated IgM and IgG titers to S. neurona. Evidence to support the point-source character of this event include the striking spatial and temporal clustering of cases and detection of high concentrations of anti-S. neurona IgM in serum of stranded animals. Concurrent exposure to the marine biotoxin domoic acid may have enhanced susceptibility of affected otters to S. neurona and exacerbated the neurological signs exhibited by stranded animals. Other factors that may have contributed to the severity of this epizootic include a large rainstorm that preceded the event and an abundance of razor clams near local beaches, attracting numerous otters close to shore within the affected area. This is the first report of a localized epizootic in marine wildlife caused by apicomplexan protozoa.

Assessing the effects of non-point source pollution on American Samoa's coral reef communities.

PubMed

Houk, Peter; Didonato, Guy; Iguel, John; Van Woesik, Robert

2005-08-01

Surveys were completed on Tutuila Island, American Samoa, to characterize reef development and assess the impacts of non-point source pollution on adjacent coral reefs at six sites. Multivariate analyses of benthic and coral community data found similar modern reef development at three locations; Aoa, Alofau, and Leone. These sites are situated in isolated bays with gentle sloping foundations. Aoa reefs had the highest estimates of crustose coralline algae cover and coral species richness, while Leone and Alofau showed high abundances of macroalgae and Porites corals. Aoa has the largest reef flat between watershed discharge and the reef slope, and the lowest human population density. Masefau and Fagaalu have a different geomorphology consisting of cemented staghorn coral fragments and steep slopes, however, benthic and coral communities were not similar. Benthic data suggest Fagaalu is heavily impacted compared with all other sites. Reef communities were assessed as bio-criteria indicators for waterbody health, using the EPA aquatic life use support designations of (1) fully supportive, (2) partially supportive, and (3) non-supportive for aquatic life. All sites resulted in a partially supportive ranking except Fagaalu, which was non-supportive. The results of this rapid assessment based upon relative benthic community measures are less desirable than long-term dataset analyses from monitoring programs, however it fills an important role for regulatory agencies required to report annual waterbody assessments. Future monitoring sites should be established to increase the number of replicates within each geological and physical setting to allow for meaningful comparisons along a gradient of hypothesized pollution levels.

NON-POINT SOURCE POLLUTION

EPA Science Inventory

Non-point source pollution is a diffuse source that is difficult to measure and is highly variable due to different rain patterns and other climatic conditions. In many areas, however, non-point source pollution is the greatest source of water quality degradation. Presently, stat...

ACHP | News | Federal Highway Administration wins Chairman's Award for

Science.gov Websites

major source of federal funding for local and state historic preservation efforts." The award was Intermodal Surface Transportation Efficiency Act began to find an appropriate balance by creating and funding largest single source of federal funding for historic preservation. The funding is provided through a

Improved Leach Testing for Evaluating Fate of Mercury and Other Metals from Management of Coal Combustion Residues

EPA Science Inventory

Coal-fired power plants, the largest domestic source of atmospheric mercury emissions in the U.S., are also a major emission source of nitrogen oxides (NOx), sulfur dioxide (S02), and particulate matter (PM). In response to the U.S. Environmental Protection Agency's (EPA's) Clean...

The southern Kalahari as a dust source: preliminary results from the field

USDA-ARS?s Scientific Manuscript database

The Kalahari encompasses one of the largest drylands in the Southern Hemisphere and it is a potentially large source of atmospheric dust in its relatively low-dust region. The severe iron depletion in the southern Indian and Atlantic Oceans, the ocean basins that receive much of the Kalahari dust, ...

INTERDISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Relaxation Property and Stability Analysis of the Quasispecies Models

NASA Astrophysics Data System (ADS)

Feng, Xiao-Li; Li, Yu-Xiao; Gu, Jian-Zhong; Zhuo, Yi-Zhong

2009-10-01

The relaxation property of both Eigen model and Crow-Kimura model with a single peak fitness landscape is studied from phase transition point of view. We first analyze the eigenvalue spectra of the replication mutation matrices. For sufficiently long sequences, the almost crossing point between the largest and second-largest eigenvalues locates the error threshold at which critical slowing down behavior appears. We calculate the critical exponent in the limit of infinite sequence lengths and compare it with the result from numerical curve fittings at sufficiently long sequences. We find that for both models the relaxation time diverges with exponent 1 at the error (mutation) threshold point. Results obtained from both methods agree quite well. From the unlimited correlation length feature, the first order phase transition is further confirmed. Finally with linear stability theory, we show that the two model systems are stable for all ranges of mutation rate. The Eigen model is asymptotically stable in terms of mutant classes, and the Crow-Kimura model is completely stable.

Megafauna and frozen soil: the drivers of atmospheric CH4 dynamics

NASA Astrophysics Data System (ADS)

Zimov, N.; Zimov, S. A.

2010-12-01

During the last deglaciation (LD) a strong increase in atmospheric methane (CH4) concentrations occurred simultaneously with a rise in Greenland temperatures indicating that in the north, during this time period, strong CH4 sources “awakened”, as additionally documented by the appearance of a strong gradient between northern (Greenland) and southern (Antarctica) hemisphere atmospheric CH4 concentrations. This rise could not be caused by wetland expansion. A reconstruction of peatland formation dynamics has indicated that wetlands on Earth were few in LD and only actively expanded 10,000 yr BP, after atmospheric CH4 concentrations began to decline. Destabilization of methane clathrates also could not be the source for atmospheric CH4 increase. Geological CH4 (including methane clathrates) has the highest deuterium content (δD) among all of the known sources of CH4 while atmospheric CH4 δD values determined for the LD were record low. To explain recorded atmospheric CH4 and its isotopic dynamics required a strong northern source, which was active only during the LD and that provided very low δD CH4 values. Such a source is permafrost thawing under anaerobic conditions (or better stated soils of mammoth steppe-tundra ecosystems). Permafrost thawing is the strongest, among known, wetland sources (usually over 100g CH4/m2yr) and has a unique isotopic signature (δD = -400 per mil (-338 to -479 per mil), δ13C = -73 per mil (-58 to -99 per mil)). The main sources of atmospheric CH4 have different isotopic signatures (δ13C, δD). The isotopic content of atmospheric CH4 is a simple function of the weight average for all of the sources. Inclusion of permafrost source into a budget model of the atmospheric methane and its isotopes allowed us to reconstruct the dynamics of methane’s main sources. Model indicated geological source to be negligible as in LGM so and in LD and Holocene. During the glaciation, the largest methane source was megafauna, whose 1.4-1.7 billion ton biomass was larger than the modern biomass of human and domestic animals combined. During the LD, the largest methane source was the thawing of steppe-tundra soils. During the Holocene the largest CH4 source was wetlands. All these estimates correspond with the scales of permafrost degradation in the LD, megafaunal extinction and increase in fire intensity derived from charcoal within stratigraphic columns.

Occurrence of phosphorus, other nutrients, and triazine herbicides in water from the Hillsdale Lake basin, Northeast Kansas, May 1994 through May 1995

USGS Publications Warehouse

Putnam, J.E.

1997-01-01

An investigation of the occurrence of phosporus, other nutrients, and triazine herbicides in water samples from the Hillsdale Lake Basin in northeast Kansas was conducted from May 1994 through May 1995. Point-source and nonpoint-source contributions of these water-quality constituents were estimated by conducting synoptic sampling at 48 sites in the basin during five periods of low- flow conditions. Samples were collected for the determination of nutrients, including total phosphorus as phosphorus, dissolved orthophosphate as phosphorus, total nitrite plus nitrate as nitrogen, and total ammonia plus organic nitrogen as nitrogen, and for selected triazine herbicides. On the basis of criteria developed by the Kansas Department of Health and Environment, the Hillsdale Water-Quality Protection Project established a goal to maintain water quality in the tributaries of the Hillsdale Lake Basin at a mean annual low-flow total phosphorus concentration of 0.05 mg/L (milligrams per liter). The mean low- flow total phosphorus concentration of water samples collected in the Big Bull Creek (which includes drainage from Martin Creek), Rock Creek, Little Bull Creek, Wade Branch, and Smith Branch subbasins during low-flow conditions ranged from 0.05 to 4.9 mg/L during this study. Of the 44 sites sampled during low flow, 95 percent had low-flow total phosphorus concentrations larger than the 0.05-mg/L criterion. Discharges from wastewater- treatment plants located in Big Bull Creek and Martin Creek subbasins and the Little Bull Creek subbasin affected nutrient concentrations. Nutrient concentrations in water samples collected from the subbasins not affected by point-source discharges generally were smaller than those in the Big Bull Creek and Little Bull Creek subbasins. Estimated annual low-flow phosphorus loads computed at sampling sites located at the outlet of the subbasins show that the Big Bull Creeksubbasin, which includes drainage from the Martin Creek subbasin, had the largest estimate annual low-flow load, 2,740 kg/yr (kilograms per year).Rock Creek, Little Bull Creek, Wade Branch, and Smith Branch subbasins contributed less annual low-flow phosphorus load, 175, 161, 234, and 22kg/yr, respectively. With the exception of the Smith Branch subbasin, the largest triazine herbicide concentrations occurred in water samples collectedduring May 1994 and May 1995. During May 1994, 10 of 17 sampling sites in the Big Bull Creek and Martin Creek subbasins, 5 of 6 sites in theRock Creek subbasin, and 4 of 10 sites in the Little Bull Creek subbasin had triazine herbicide concentrations in water larger than the U.S.Environmental Protection Agency's Maximum Contaminant Level (MCL), which is an annual mean 3.0 ug/L (micrograms per liter) for atrazine indrinking water. During May 1995, 7 of 19 sites in the Big Bull Creek and Martin Creek subbasins, 5 of 6 sites in the Rock Creek subbasin, 1 of 12 sites in the Little Bull Creek subbasin, and 2 of 4 sites in the Wade Branch subbasin had samples with trazine herbicide concentrations larger than the MCL.Water samples collected in the Rock Creek subbasins had the largest mean triazine herbicide concentrations during May 1994 and May 1995, 6.4 and 4.5 ug/L, respectively.

Stress Models of the Annual Hydrospheric, Atmospheric, Thermal, and Tidal Loading Cycles on California Faults: Perturbation of Background Stress and Changes in Seismicity

NASA Astrophysics Data System (ADS)

Johnson, Christopher W.; Fu, Yuning; Bürgmann, Roland

2017-12-01

Stresses in the lithosphere arise from multiple natural loading sources that include both surface and body forces. The largest surface loads include near-surface water storage, snow and ice, atmosphere pressure, ocean loading, and temperature changes. The solid Earth also deforms from celestial body interactions and variations in Earth's rotation. We model the seasonal stress changes in California from 2006 through 2014 for seven different loading sources with annual periods to produce an aggregate stressing history for faults in the study area. Our modeling shows that the annual water loading, atmosphere, temperature, and Earth pole tides are the largest loading sources and should each be evaluated to fully describe seasonal stress changes. In California we find that the hydrological loads are the largest source of seasonal stresses. We explore the seasonal stresses with respect to the background principal stress orientation constrained with regional focal mechanisms and analyze the modulation of seismicity. Our results do not suggest a resolvable seasonal variation for the ambient stress orientation in the shallow crust. When projecting the seasonal stresses into the background stress orientation we find that the timing of microseismicity modestly increases from an 8 kPa seasonal mean-normal-stress perturbation. The results suggest that faults in California are optimally oriented with the background stress field and respond to subsurface pressure changes, possibly due to processes we have not considered in this study. At any time a population of faults are near failure as evident from earthquakes triggered by these slight seasonal stress perturbations.

Consolidation and the transformation of competition in health insurance.

PubMed

Robinson, James C

2004-01-01

This paper presents data on fifty state and substate insurance markets, in terms of the 2003 relative shares of the largest health plans and the antitrust index of concentration. It presents 2000-03 data on rates of growth in premiums, costs, operating earnings, returns on equity, and share prices for the nation's largest health plans (Well-Point, Anthem, Aetna, and CIGNA). Private insurers face renewed price and profit pressures in the short term, but long-term prospects depend on the emergence of new products and new competitors in an increasingly consolidated industry.

Clinical measurement of the height of the interproximal contact area in maxillary anterior teeth.

PubMed

Sghaireen, Mohd G; Al-Zarea, Bader K; Al-Shorman, Hisham M; Al-Omiri, Mahmoud K

2013-11-01

To clinically quantify the apicoincisal height of interproximal areas directly in patients' mouths. Thirty participants (11 females and 9 males, mean age=26±1.5 years) were recruited into this study. Measurement of interproximal contact areas was carried out directly in patients' mouths using digital caliper (TERENSA, USA) with measuring accuracy of 0.01 mm. The interproximal contact areas that were measured are: central incisor to central incisor, central incisor to lateral incisor, lateral incisor to canine, and canine to first premolar on both sides of the jaw. Statistical significance was based on probability values less than 0.05 (p<0.05). The largest contact point was the one present between central incisors and it ranged from 2.9 to 6.5 mm. On the other hand, the contact point between canine and first premolar was the smallest on both sides of the arch and ranged from 0.6 to 2.5 mm. The dimensions of the contact points declined as we move from anterior area backwards. Statistical analysis using t-test showed that there were significant differences between the measurements of interproximal points of each tooth (P<0.05). the apicogingival dimension of the contact point decreased as we moved from anterior to posterior teeth. The contact area between the central incisors was largest and the one between canine and premolar was the smallest. This study is the first to report direct intra-oral clinical measurement of contact points. Clinical evaluation of contact point dimensions using digital caliber is a viable, quick and accurate method to use.

Effects of Anthropogenic Nitrogen Loading on Riverine Nitrogen Export in the Northeastern USA

NASA Astrophysics Data System (ADS)

Boyer, E. W.; Goodale, C. L.; Howarth, R. W.

2001-05-01

Human activities have greatly altered the nitrogen (N) cycle, accelerating the rate of N fixation in landscapes and delivery of N to water bodies. To examine the effects of anthropogenic N inputs on riverine N export, we quantified N inputs and riverine N loss for 16 catchments along a latitudinal profile from Maine to Virginia, which encompass a range of climatic variability and are major drainages to the coast of the North Atlantic Ocean. We quantified inputs of N to each catchment: atmospheric deposition, fertilizer application, agricultural and forest biological N fixation, and the net import of N in food and feed. We compared these inputs with N losses from the system in riverine export. The importance of the relative sources varies widely by watershed and is related to land use. Atmospheric deposition was the largest source (>60%) to the forested catchments of northern New England (e.g., Penobscot and Kennebec); import of N in food was the largest source of N to the more populated regions of southern New England (e.g., Charles and Blackstone); and agricultural inputs were the dominant N sources in the Mid-Atlantic region (e.g., Schuylkill and Potomac). Total N inputs to each catchment increased with percent cover in agriculture and urban land, and decreased with percent forest. Over the combined area of the catchments, net atmospheric deposition was the largest single source input (34%), followed by imports of N in food and feed (24%), fixation in agricultural lands (21%), fertilizer use (15%), and fixation in forests (6%). Riverine export of N is well correlated with N inputs, but it accounts for only a fraction (28%) of the total N inputs. This work provides an understanding of the sources of N in landscapes, and highlights how human activities impact N cycling in the northeast region.

SOURCES AND TRANSFORMATIONS OF NITROGEN, CARBON, AND PHOSPHORUS IN THE POTOMAC RIVER ESTUARY

NASA Astrophysics Data System (ADS)

Pennino, M. J.; Kaushal, S.

2009-12-01

Global transport of nitrogen (N), carbon (C), and phosphorus (P) in river ecosystems has been dramatically altered due to urbanization. We examined the capacity of a major tributary of the Chesapeake Bay, the Potomac River, to transform carbon, nitrogen, and phosphorus inputs from the world’s largest advanced wastewater treatment facility (Washington D.C. Water and Sewer Authority). Surface water and effluent samples were collected along longitudinal transects of the Potomac River seasonally and compared to long-term interannual records of carbon, nitrogen, and phosphorus. Water samples from seasonal longitudinal transects were analyzed for dissolved organic and inorganic nitrogen and phosphorus, total organic carbon, and particulate carbon, nitrogen, and phosphorus. The source and quality of organic matter was characterized using fluorescence spectroscopy, excitation emission matrices (EEMs), and PARAFAC modeling. Sources of nitrate were tracked using stable isotopes of nitrogen and oxygen. Along the river network stoichiometric ratios of C, N, and P were determined across sites and related to changes in flow conditions. Land use data and historical water chemistry data were also compared to assess the relative importance of non-point sources from land-use change versus point-sources of carbon, nitrogen, and phosphorus. Preliminary data from EEMs suggested that more humic-like organic matter was important above the wastewater treatment plant, but more protein-like organic matter was present below the treatment plant. Levels of nitrate and ammonia showed increases within the vicinity of the wastewater treatment outfall, but decreased rapidly downstream, potentially indicating nutrient uptake and/or denitrification. Phosphate levels decreased gradually along the river with a small increase near the wastewater treatment plant and a larger increase and decrease further downstream near the high salinity zone. Total organic carbon levels show a small decrease downstream. Ecological stoichiometric ratios along the river indicate increases in C/N ratios downstream, but no corresponding trend with C/P ratios. The N/P ratios increased directly below the treatment plant and then decreased gradually downstream. The C/N/P ratios remained level until the last two sampling stations within 20 miles of the Chesapeake Bay, where there is a large increase. Despite large inputs, there may be large variations in sources and ecological stoichiometry along rivers and estuaries, and knowledge of these transformations will be important in predicting changes in the amounts, forms, and stoichiometry of nutrient loads to coastal waters.

An improved DPSM technique for modelling ultrasonic fields in cracked solids

NASA Astrophysics Data System (ADS)

Banerjee, Sourav; Kundu, Tribikram; Placko, Dominique

2007-04-01

In recent years Distributed Point Source Method (DPSM) is being used for modelling various ultrasonic, electrostatic and electromagnetic field modelling problems. In conventional DPSM several point sources are placed near the transducer face, interface and anomaly boundaries. The ultrasonic or the electromagnetic field at any point is computed by superimposing the contributions of different layers of point sources strategically placed. The conventional DPSM modelling technique is modified in this paper so that the contributions of the point sources in the shadow region can be removed from the calculations. For this purpose the conventional point sources that radiate in all directions are replaced by Controlled Space Radiation (CSR) sources. CSR sources can take care of the shadow region problem to some extent. Complete removal of the shadow region problem can be achieved by introducing artificial interfaces. Numerically synthesized fields obtained by the conventional DPSM technique that does not give any special consideration to the point sources in the shadow region and the proposed modified technique that nullifies the contributions of the point sources in the shadow region are compared. One application of this research can be found in the improved modelling of the real time ultrasonic non-destructive evaluation experiments.

On the assessment of spatial resolution of PET systems with iterative image reconstruction

NASA Astrophysics Data System (ADS)

Gong, Kuang; Cherry, Simon R.; Qi, Jinyi

2016-03-01

Spatial resolution is an important metric for performance characterization in PET systems. Measuring spatial resolution is straightforward with a linear reconstruction algorithm, such as filtered backprojection, and can be performed by reconstructing a point source scan and calculating the full-width-at-half-maximum (FWHM) along the principal directions. With the widespread adoption of iterative reconstruction methods, it is desirable to quantify the spatial resolution using an iterative reconstruction algorithm. However, the task can be difficult because the reconstruction algorithms are nonlinear and the non-negativity constraint can artificially enhance the apparent spatial resolution if a point source image is reconstructed without any background. Thus, it was recommended that a background should be added to the point source data before reconstruction for resolution measurement. However, there has been no detailed study on the effect of the point source contrast on the measured spatial resolution. Here we use point source scans from a preclinical PET scanner to investigate the relationship between measured spatial resolution and the point source contrast. We also evaluate whether the reconstruction of an isolated point source is predictive of the ability of the system to resolve two adjacent point sources. Our results indicate that when the point source contrast is below a certain threshold, the measured FWHM remains stable. Once the contrast is above the threshold, the measured FWHM monotonically decreases with increasing point source contrast. In addition, the measured FWHM also monotonically decreases with iteration number for maximum likelihood estimate. Therefore, when measuring system resolution with an iterative reconstruction algorithm, we recommend using a low-contrast point source and a fixed number of iterations.

Far-field pressurization likely caused one of the largest injection induced earthquakes by reactivating a large pre-existing basement fault structure

USGS Publications Warehouse

Yeck, William; Weingarten, Matthew; Benz, Harley M.; McNamara, Daniel E.; Bergman, E.; Herrmann, R.B; Rubinstein, Justin L.; Earle, Paul

2016-01-01

The Mw 5.1 Fairview, Oklahoma, earthquake on 13 February 2016 and its associated seismicity produced the largest moment release in the central and eastern United States since the 2011 Mw 5.7 Prague, Oklahoma, earthquake sequence and is one of the largest earthquakes potentially linked to wastewater injection. This energetic sequence has produced five earthquakes with Mw 4.4 or larger. Almost all of these earthquakes occur in Precambrian basement on a partially unmapped 14 km long fault. Regional injection into the Arbuckle Group increased approximately sevenfold in the 36 months prior to the start of the sequence (January 2015). We suggest far-field pressurization from clustered, high-rate wells greater than 12 km from this sequence induced these earthquakes. As compared to the Fairview sequence, seismicity is diffuse near high-rate wells, where pressure changes are expected to be largest. This points to the critical role that preexisting faults play in the occurrence of large induced earthquakes.

High-Resolution Analysis of Seismicity Induced at Berlín Geothermal Field, El Salvador

NASA Astrophysics Data System (ADS)

Kwiatek, G.; Bulut, F.; Dresen, G. H.; Bohnhoff, M.

2012-12-01

We investigate induced microseismic activity monitored at Berlín Geothermal Field, El Salvador, during a hydraulic stimulation. The site was monitored for a time period of 17 months using thirteen 3-component seismic stations located in shallow boreholes. Three stimulations were performed in the well TR8A with a maximum injection rate and well head pressure of 160l/s and 130bar, respectively. For the entire time period of our analysis, the acquisition system recorded 581 events with moment magnitudes ranging between -0.5 and 3.7. The initial seismic catalog provided by the operator was substantially improved: 1) We re-picked P- and S-wave onsets and relocated the seismic events using the double-difference relocation algorithm based on cross-correlation derived differential arrival time data. Forward modeling was performed using a local 1D velocity model instead of homogeneous full-space. 2) We recalculated source parameters using the spectral fitting method and refined the results applying the spectral ratio method. We investigated the source parameters and spatial and temporal changes of the seismic activity based on the refined dataset and studied the correlation between seismic activity and production. The achieved hypocentral precision allowed resolving the spatiotemporal changes in seismic activity down to a scale of a few meters. The application of spectral ratio method significantly improved the quality of source parameters in a high-attenuating and complex geological environment. Of special interest is the largest event (Mw3.7) and its nucleation process. We investigate whether the refined seismic data display any signatures that the largest event is triggered by the shut-in of the well. We found seismic activity displaying clear spatial and temporal patterns that could be easily related to the amount of water injected into the well TR8A and other reinjection wells in the investigated area. The migration of seismicity outside of injection point is observed while injection rate is increasing. The locations of migrating seismic events are related to the existing fault system that is independently supported by calculated focal mechanisms. We found that the event migration occurs until the shut-in of the well. We observe that the large magnitude events are observed right after the shut-in, located in undamaged parts of the fault system. Results show that the following stimulation episodes require increased injection rate level (or increased well head pressure) to re-activate the seismic activity (Kaiser Effect, "Crustal memory" effect). The static stress drop values increase with the distance from injection point that is interpreted to be related to pore pressure perturbations introduced by stimulation of the injection well.

Propulsion Airframe Aeroacoustic Integration Effects for a Hybrid Wing Body Aircraft Configuration

NASA Technical Reports Server (NTRS)

Czech, Michael J.; Thomas, Russell H.; Elkoby, Ronen

2010-01-01

An extensive experimental investigation was performed to study the propulsion airframe aeroacoustic effects of a high bypass ratio engine for a hybrid wing body aircraft configuration where the engine is installed above the wing. The objective was to provide an understanding of the jet noise shielding effectiveness as a function of engine gas condition and location as well as nozzle configuration. A 4.7% scale nozzle of a bypass ratio seven engine was run at characteristic cycle points under static and forward flight conditions. The effect of the pylon and its orientation on jet noise was also studied as a function of bypass ratio and cycle condition. The addition of a pylon yielded significant spectral changes lowering jet noise by up to 4dB at high polar angles and increasing it by 2 to 3dB at forward angles. In order to assess jet noise shielding, a planform representation of the airframe model, also at 4.7% scale was traversed relative to the jet nozzle from downstream to several diameters upstream of the wing trailing edge. Installations at two fan diameters upstream of the wing trailing edge provided only limited shielding in the forward arc at high frequencies for both the axisymmetric and a conventional round nozzle with pylon. This was consistent with phased array measurements suggesting that the high frequency sources are predominantly located near the nozzle exit and, consequently, are amenable to shielding. The mid to low frequencies sources were observed further downstream and shielding was insignificant. Chevrons were designed and used to impact the distribution of sources with the more aggressive design showing a significant upstream migration of the sources in the mid frequency range. Furthermore, the chevrons reduced the low frequency source levels and the typical high frequency increase due to the application of chevron nozzles was successfully shielded. The pylon was further modified with a technology that injects air through the shelf of the pylon which was effective in reducing low frequency noise and moving jet noise sources closer to the nozzle exit. In general, shielding effectiveness varied as a function of cycle condition with the cutback condition producing higher shielding compared to sideline power. The configuration with a more strongly immersed chevron and a pylon oriented opposite to the microphones produced the largest reduction in jet noise. In addition to the jet noise source, the shielding of a broadband point noise source was documented with up to 20 dB of noise reduction at directivity angles directly under the shielding surface.

Propulsion Airframe Aeroacoustic Integration Effects for a Hybrid Wing Body Aircraft Configuration

NASA Technical Reports Server (NTRS)

Czech, Michael J.; Thomas, Russell H; Elkoby, Ronen

2012-01-01

An extensive experimental investigation was performed to study the propulsion airframe aeroacoustic effects of a high bypass ratio engine for a hybrid wing body aircraft configuration where the engine is installed above the wing. The objective was to provide an understanding of the jet noise shielding effectiveness as a function of engine gas condition and location as well as nozzle configuration. A 4.7% scale nozzle of a bypass ratio seven engine was run at characteristic cycle points under static and forward flight conditions. The effect of the pylon and its orientation on jet noise was also studied as a function of bypass ratio and cycle condition. The addition of a pylon yielded significant spectral changes lowering jet noise by up to 4 dB at high polar angles and increasing it by 2 to 3 dB at forward angles. In order to assess jet noise shielding, a planform representation of the airframe model, also at 4.7% scale was traversed such that the jet nozzle was positioned from downstream of to several diameters upstream of the airframe model trailing edge. Installations at two fan diameters upstream of the wing trailing edge provided only limited shielding in the forward arc at high frequencies for both the axisymmetric and a conventional round nozzle with pylon. This was consistent with phased array measurements suggesting that the high frequency sources are predominantly located near the nozzle exit and, consequently, are amenable to shielding. The mid to low frequency sources were observed further downstream and shielding was insignificant. Chevrons were designed and used to impact the distribution of sources with the more aggressive design showing a significant upstream migration of the sources in the mid frequency range. Furthermore, the chevrons reduced the low frequency source levels and the typical high frequency increase due to the application of chevron nozzles was successfully shielded. The pylon was further modified with a technology that injects air through the shelf of the pylon which was effective in reducing low frequency noise and moving jet noise sources closer to the nozzle exit. In general, shielding effectiveness varied as a function of cycle condition with the cutback condition producing higher shielding compared to sideline power. The configuration with a more strongly immersed chevron and a pylon oriented opposite to the microphones produced the largest reduction in jet noise. In addition to the jet noise source, the shielding of a broadband point noise source was documented with up to 20 dB of noise reduction at directivity angles directly under the shielding surface.

Assessing the effect of nutrient mitigation measures in the watersheds of the Southern Bight of the North Sea.

PubMed

Thieu, Vincent; Garnier, Josette; Billen, Gilles

2010-02-15

The Seine, Somme, and Scheldt Rivers (France, Belgium, and Netherlands) are the major delivering rivers flowing into the continental coastal zone of the Southern Bight of the North Sea, an area regularly affected by eutrophication problems. In the present work, the Seneque-Riverstrahler model was implemented in a multi-regional case study in order to test several planned mitigation measures aimed at limiting stream nutrient contamination and restoring balanced nutrient ratios at the coastal zone. This modeling approach, which is spatially distributed at the basin scale, allows assessing the impact of any change in human activities, which widely differ over the three basins. Here, we define realistic scenarios based on currently proposed measures to reduce point and non-point sources, such as the upgrading of wastewater treatment, the introduction of catch crops, and the development of extensive farming. An analysis of the current situation showed that a 47-72% reduction in P point-source emissions within the three basins could be reached if the intended P treatment was generalized to the largest treatment plants. However, only an overall 14-23% reduction in N could be achieved at the outlet of the three basins, by combining improved wastewater treatment and land use with management measures aimed at regulating agricultural practices. Nonetheless, in spite of these efforts, N will still be exported in large excess with respect to the equilibrium defined by the Redfield ratios, even in the most optimistic hypothesis describing the long-term response of groundwater nitrate concentrations. A comprehensive assessment of these mitigation measures supports the need for additional reductions of nutrient losses from agriculture to control harmful algae development. It also stresses the relevance of this mechanistic approach, in which nutrient transfers from land to sea can be calculated, as an integrated strategy to test policy recommendations.

Sources and sinks of filtered total mercury and concentrations of total mercury of solids and of filtered methylmercury, Sinclair Inlet, Kitsap County, Washington, 2007-10

USGS Publications Warehouse

Paulson, Anthony J.; Dinicola, Richard S.; Noble, Marlene A.; Wagner, Richard J.; Huffman, Raegan L.; Moran, Patrick W.; DeWild, John F.

2012-01-01

The majority of filtered total mercury in the marine water of Sinclair Inlet originates from salt water flowing from Puget Sound. About 420 grams of filtered total mercury are added to Sinclair Inlet each year from atmospheric, terrestrial, and sedimentary sources, which has increased filtered total mercury concentrations in Sinclair Inlet (0.33 nanograms per liter) to concentrations greater than those of the Puget Sound (0.2 nanograms per liter). The category with the largest loading of filtered total mercury to Sinclair Inlet included diffusion of porewaters from marine sediment to the water column of Sinclair Inlet and discharge through the largest stormwater drain on the Bremerton naval complex, Bremerton, Washington. However, few data are available to estimate porewater and stormwater releases with any certainty. The release from the stormwater drain does not originate from overland flow of stormwater. Rather total mercury on soils is extracted by the chloride ions in seawater as the stormwater is drained and adjacent soils are flushed with seawater by tidal pumping. Filtered total mercury released by an unknown freshwater mechanism also was observed in the stormwater flowing through this drain. Direct atmospheric deposition on the Sinclair Inlet, freshwater discharge from creek and stormwater basins draining into Sinclair Inlet, and saline discharges from the dry dock sumps of the naval complex are included in the next largest loading category of sources of filtered total mercury. Individual discharges from a municipal wastewater treatment plant and from the industrial steam plant of the naval complex constituted the loading category with the third largest loadings. Stormwater discharge from the shipyard portion of the naval complex and groundwater discharge from the base are included in the loading category with the smallest loading of filtered total mercury. Presently, the origins of the solids depositing to the sediment of Sinclair Inlet are uncertain, and consequently, concentrations of sediments can be qualitatively compared only to total mercury concentrations of solids suspended in the water column. Concentrations of total mercury of suspended solids from creeks, stormwater, and even wastewater effluent discharging into greater Sinclair Inlet were comparable to concentrations of solids suspended in the water column of Sinclair Inlet. Concentrations of total mercury of suspended solids were significantly lower than those of marine bed sediment of Sinclair Inlet; these suspended solids have been shown to settle in Sinclair Inlet. The settling of suspended solids in the greater Sinclair Inlet and in Operable Unit B Marine of the naval complex likely will result in lower concentrations of total mercury in sediments. Such a decrease in total mercury concentrations was observed in the sediment of Operable Unit B Marine in 2010. However, total mercury concentrations of solids discharged from several sources from the Bremerton naval complex were higher than concentrations in sediment collected from Operable Unit B Marine. The combined loading of solids from these sources is small compared to the amount of solids depositing in OU B Marine. However, total mercury concentration in sediment collected at a monitoring station just offshore one of these sources, the largest stormwater drain on the Bremerton naval complex, increased considerably in 2010. Low methylmercury concentrations were detected in groundwater, stormwater, and effluents discharged from the Bremerton naval complex. The highest methylmercury concentrations were measured in the porewaters of highly reducing marine sediment in greater Sinclair Inlet. The marine sediment collected off the largest stormwater drain contained low concentrations of methylmercury in porewater because these sediments were not highly reducing.

Normal modes from the 2013 Sea of Okhotsk earthquake, the largest deep event ever recorded

NASA Astrophysics Data System (ADS)

Okal, E. A.

2013-12-01

With a moment of 4.1 10**28 dyn*cm, the Sea of Okhotsk earthquake of 24 May 2013 is the largest deep event ever recorded. This provides a unique opportunity to study the excitation of low-frequency normal modes, including overtone and radial ones. The principal questions addressed will be the possible existence of a slow component to the source, which is not warranted by preliminary results; and the possible presence of an isotropic component to the moment tensor of its source. The latter was strongly debated in the case of the 1970 Colombian event (Gilbert and Dziewonski, 1973; Okal and Geller, 1979), and clearly found absent from the source of the 1994 Bolivian one (Kikuchi and Kanamori, 1994; Okal, 1996). Critical in this respect will be the investigation of the relative excitation of the the radial modes, and in particular, the fundamental 0s0, for which a sufficiently long (90 days) time series was not available by the submission deadline.

Water-quality conditions of the lower Boise River, Ada and Canyon Counties, Idaho, May 1994 through February 1997

USGS Publications Warehouse

Mullins, William H.

1998-01-01

Agricultural land and water use, wastewater treatment facility discharges, land development, road construction, urban runoff, confined-animal feeding operations, reservoir operations, and river channelization affect the water quality and biotic integrity of the lower Boise River between Lucky Peak Dam and the river's mouth at Parma, Idaho. During May 1994 through February 1997, 4 sites on the Boise River, 12 tributary/drain sites, and 3 wastewater treatment facilities were sampled at various intervals during the irrigation (high-flow) and post-irrigation (low-flow) seasons to determine sources, concentrations, and relative loads of nutrients and suspended sediment. Discharge entering the Boise River from the 12 tributary/drain sites and 3 wastewater treatment facilities was measured to determine the nutrient loads being contributed from each source. Total nitrogen, total phosphorus, and suspended sediment concentrations and loads tended to increase in a downstream direction along the Boise River. Among the 15 sources of discharge to the Boise River, 3 southside tributary/drains and the West Boise wastewater treatment facility contributed the largest loads of total nitrogen; the median daily load was more than 2,000 pounds per day. The West Boise wastewater treatment facility contributed the largest median daily load of total phosphorus (810 pounds per day); Dixie Drain contributed the largest median daily load of suspended sediment (26.4 tons per day). Nitrogen-to-phosphorus ratios at the four Boise River sites indicated that phosphorus could be limiting algal growth at the Diversion Dam site, whereas nitrogen could be limiting algal growth at the Glenwood and Middleton sites during some parts of the year. Algal growth in the Boise River near Parma did not appear to be nutrient limited. Because of the complexity of the plumbing system in the lower Boise River (numerous diversions and inflow points), accurate comparisons between discharge and nutrient loads entering the river at measured sites during high-flow sampling periods were difficult. During low-flow sampling periods, southside tributary/drains contributed most of the discharge and total nitrogen load, and wastewater treatment facilities contributed most of the total phosphorus load to the Boise River. During the 50-day period July 18 through September 5, 1996, the Idaho State standard for maximum daily average temperature for coldwater biota was exceeded by 34 percent at Middleton, 48 percent at Caldwell, and 80 percent near Parma. Violations of State standards for primary and secondary contact recreation were observed at all tributary/ drains and in the Boise River near Parma. Median instantaneous concentrations of fecal coliform bacteria exceeded State standards for primary contact recreation at five tributary/drains and exceeded standards for secondary contact recreation at one tributary/drain (Dixie Drain).

Review and Comparison of the Search Effectiveness and User Interface of Three Major Online Chemical Databases

ERIC Educational Resources Information Center

Bharti, Neelam; Leonard, Michelle; Singh, Shailendra

2016-01-01

Online chemical databases are the largest source of chemical information and, therefore, the main resource for retrieving results from published journals, books, patents, conference abstracts, and other relevant sources. Various commercial, as well as free, chemical databases are available. SciFinder, Reaxys, and Web of Science are three major…

Quantification of Shallow Groundwater Nutrient Dynamics in Septic Areas

Treesearch

Ying Ouyang; Jia-En Zhang

2012-01-01

Of all groundwater pollution sources, septic systems are the second largest source of groundwater nitrate contamination in USA. This study investigated shallow groundwater (SGW) nutrient dynamics in septic areas at the northern part of the Lower St. Johns River Basin, Florida, USA. Thirty-five SGW-monitoring wells, located at nine different urban areas served by septic...

75 FR 522 - National Emission Standards for Hazardous Air Pollutants: Area Source Standards for Prepared...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-05

... to what constitutes the generally available control technology or management practices for the area... area sources, pose the greatest threat to public health in the largest number of urban areas. EPA implemented this provision in 1999 in the Integrated Urban Air Toxics Strategy, (64 FR 38715, July 19, 1999...

Ownership, financing, and management strategies of the ten largest for-profit nursing home chains in the United States.

PubMed

Harrington, Charlene; Hauser, Clarilee; Olney, Brian; Rosenau, Pauline Vaillancourt

2011-01-01

This study examined the ownership, financing, and management strategies of the 10 largest for-profit nursing home chains in the United States, including the four largest chains purchased by private equity corporations. Descriptive data were collected from Internet searches, company reports, and other sources for the decade 1998-2008. Since 1998, the largest chains have made many changes in their ownership and structure, and some have converted from publicly traded companies to private ownership. This study shows the increasing complexity of corporate nursing home ownership and the lack of public information about ownership and financial status. The chains have used strategies to maximize shareholder and investor value that include increasing Medicare revenues, occupancy rates, and company diversification, establishing multiple layers of corporate ownership, developing real estate investment trusts, and creating limited liability companies. These strategies enhance shareholder and investor profits, reduce corporate taxes, and reduce liability risk. There is a need for greater transparency in ownership and financial reporting and for more government oversight of the largest for-profit chains, including those owned by private equity companies.

High-frequency source radiation during the 2011 Tohoku-Oki earthquake, Japan, inferred from KiK-net strong-motion seismograms

NASA Astrophysics Data System (ADS)

Kumagai, Hiroyuki; Pulido, Nelson; Fukuyama, Eiichi; Aoi, Shin

2013-01-01

investigate source processes of the 2011 Tohoku-Oki earthquake, we utilized a source location method using high-frequency (5-10 Hz) seismic amplitudes. In this method, we assumed far-field isotropic radiation of S waves, and conducted a spatial grid search to find the best fitting source locations along the subducted slab in each successive time window. Our application of the method to the Tohoku-Oki earthquake resulted in artifact source locations at shallow depths near the trench caused by limited station coverage and noise effects. We then assumed various source node distributions along the plate, and found that the observed seismograms were most reasonably explained when assuming deep source nodes. This result suggests that the high-frequency seismic waves were radiated at deeper depths during the earthquake, a feature which is consistent with results obtained from teleseismic back-projection and strong-motion source model studies. We identified three high-frequency subevents, and compared them with the moment-rate function estimated from low-frequency seismograms. Our comparison indicated that no significant moment release occurred during the first high-frequency subevent and the largest moment-release pulse occurred almost simultaneously with the second high-frequency subevent. We speculated that the initial slow rupture propagated bilaterally from the hypocenter toward the land and trench. The landward subshear rupture propagation consisted of three successive high-frequency subevents. The trenchward propagation ruptured the strong asperity and released the largest moment near the trench.

Volume 2 - Point Sources

EPA Pesticide Factsheets

Point source emission reference materials from the Emissions Inventory Improvement Program (EIIP). Provides point source guidance on planning, emissions estimation, data collection, inventory documentation and reporting, and quality assurance/quality contr

Energy-based dosimetry of low-energy, photon-emitting brachytherapy sources

NASA Astrophysics Data System (ADS)

Malin, Martha J.

Model-based dose calculation algorithms (MBDCAs) for low-energy, photon-emitting brachytherapy sources have advanced to the point where the algorithms may be used in clinical practice. Before these algorithms can be used, a methodology must be established to verify the accuracy of the source models used by the algorithms. Additionally, the source strength metric for these algorithms must be established. This work explored the feasibility of verifying the source models used by MBDCAs by measuring the differential photon fluence emitted from the encapsulation of the source. The measured fluence could be compared to that modeled by the algorithm to validate the source model. This work examined how the differential photon fluence varied with position and angle of emission from the source, and the resolution that these measurements would require for dose computations to be accurate to within 1.5%. Both the spatial and angular resolution requirements were determined. The techniques used to determine the resolution required for measurements of the differential photon fluence were applied to determine why dose-rate constants determined using a spectroscopic technique disagreed with those computed using Monte Carlo techniques. The discrepancy between the two techniques had been previously published, but the cause of the discrepancy was not known. This work determined the impact that some of the assumptions used by the spectroscopic technique had on the accuracy of the calculation. The assumption of isotropic emission was found to cause the largest discrepancy in the spectroscopic dose-rate constant. Finally, this work improved the instrumentation used to measure the rate at which energy leaves the encapsulation of a brachytherapy source. This quantity is called emitted power (EP), and is presented as a possible source strength metric for MBDCAs. A calorimeter that measured EP was designed and built. The theoretical framework that the calorimeter relied upon to measure EP was established. Four clinically relevant 125I brachytherapy sources were measured with the instrument. The accuracy of the measured EP was compared to an air-kerma strength-derived EP to test the accuracy of the instrument. The instrument was accurate to within 10%, with three out of the four source measurements accurate to within 4%.

Quantitative PET and SPECT performance characteristics of the Albira Trimodal pre-clinical tomograph

NASA Astrophysics Data System (ADS)

Spinks, T. J.; Karia, D.; Leach, M. O.; Flux, G.

2014-02-01

The Albira Trimodal pre-clinical scanner comprises PET, SPECT and CT sub-systems and thus provides a range of pre-clinical imaging options. The PET component consists of three rings of single-crystal LYSO detectors with axial/transverse fields-of-view (FOVs) of 148/80 mm. The SPECT component has two opposing CsI detectors (100 × 100 mm2) with single-pinhole (SPH) or multi(9)-pinhole (MPH) collimators; the detectors rotate in 6° increments and their spacing can be adjusted to provide different FOVs (25 to 120 mm). The CT sub-system provides ‘low’ (200 µA, 35 kVp) or ‘high’ (400 µA, 45 kVp) power x-rays onto a flat-panel CsI detector. This study examines the performance characteristics and quantitative accuracy of the PET and SPECT components. Using the NEMA NU 4-2008 specifications (22Na point source), the PET spatial resolution is 1.5 + 0.1 mm on axis and sensitivity 6.3% (axial centre) and 4.6% (central 70 mm). The usable activity range is ≤ 10 MBq (18F) over which good linearity (within 5%) is obtained for a uniform cylinder spanning the axial FOV; increasing deviation from linearity with activity is, however, observed for the NEMA (mouse) line source phantom. Image uniformity axially is within 5%. Spatial resolution (SPH/MPH) for the minimum SPECT FOV used for mouse imaging (50 mm) is 1.5/1.7 mm and point source sensitivity 69/750 cps MBq-1. Axial uniformity of SPECT images (%CV of regions-of-interest counts along the axis) is mostly within 8% although there is a range of 30-40% for the largest FOV. The variation is significantly smaller within the central 40 mm. Instances of count rate nonlinearity (PET) and axial non-uniformity (SPECT) were found to be reproducible and thus amenable to empirical correction.

Monitoring and Analysis of Nonpoint Source Pollution - Case study on terraced paddy fields in an agricultural watershed

NASA Astrophysics Data System (ADS)

Chen, Shih-Kai; Jang, Cheng-Shin; Yeh, Chun-Lin

2013-04-01

The intensive use of chemical fertilizer has negatively impacted environments in recent decades, mainly through water pollution by nitrogen (N) and phosphate (P) originating from agricultural activities. As a main crop with the largest cultivation area about 0.25 million ha per year in Taiwan, rice paddies account for a significant share of fertilizer consumption among agriculture crops. This study evaluated the fertilization of paddy fields impacting return flow water quality in an agricultural watershed located at Hsinchu County, northern Taiwan. Water quality monitoring continued for two crop-periods in 2012, around subject to different water bodies, including the irrigation water, drainage water, and shallow groundwater. The results indicated that obviously increasing of ammonium-N, nitrate-N and TP concentrations in the surface drainage water were observed immediately following three times of fertilizer applications (including basal, tillering, and panicle fertilizer application), but reduced to relatively low concentrations after 7-10 days after each fertilizer application. Groundwater quality monitoring showed that the observation wells with the more shallow water depth, the more significant variation of concentrations of ammonium-N, nitrate-N and TP could be observed, which means that the contamination potential of nutrient of groundwater is related not only to the impermeable plow sole layer but also to the length of percolation route in this area. The study also showed that the potential pollution load of nutrient could be further reduced by well drainage water control and rational fertilizer management, such as deep-water irrigation, reuse of return flow, the rational application of fertilizers, and the SRI (The System of Rice Intensification) method. The results of this study can provide as an evaluation basis to formulate effective measures for agricultural non-point source pollution control and the reuse of agricultural return flow. Keywords:Chemical fertilizer, Nitrogen, Phosphorus, Paddy field, Non-point source pollution.

Impact of forecasted changes in Polish economy (2015 and 2020) on nutrient emission into the river basins.

PubMed

Pastuszak, Marianna; Kowalkowski, Tomasz; Kopiński, Jerzy; Stalenga, Jarosław; Panasiuk, Damian

2014-09-15

Poland, with its large drainage area, with 50% contribution of agricultural land and 45% contribution of population to overall agricultural land area and population number in the Baltic catchment, is the largest exporter of riverine nitrogen (N) and phosphorus (P) to the sea. The economic transition has resulted in substantial, statistically significant decline in N, P export from Polish territory to the Baltic Sea. Following the obligations arising from the Helsinki Commission (HELCOM) declarations, in the coming years, Poland is expected to reduce riverine N loads by ca. 25% and P loads by ca. 60% as referred to the average flow normalized loads recorded in 1997-2003. The aim of this paper is to estimate annual source apportioned N and P emissions into these river basins in 2015 and 2020 with application of modeling studies (MONERIS). Twelve scenarios, encompassing changes in anthropogenic (diffuse, point source) and natural pressure (precipitation, water outflow due to climate change), have been applied. Modeling outcome for the period 2003-2008 served as our reference material. In applied scenarios, N emission into the Oder basin in 2015 and 2020 shows an increase from 4.2% up to 9.1% as compared with the reference period. N emission into the Vistula basin is more variable and shows an increase by max. 17.8% or a decrease by max. 4.7%, depending on the scenario. The difference between N emission into the Oder and Vistula basins is related to the catchment peculiarities and handling of point sources emission. P emission into both basins shows identical scenario patters and a maximum decrease reaches 17.8% in the Oder and 16.7% in the Vistula basin. Despite a declining tendency in P loads in both rivers in all the scenarios, HELCOM targeted P load reduction is not feasible. Copyright © 2014 Elsevier B.V. All rights reserved.

A novel method for the evaluation of uncertainty in dose-volume histogram computation.

PubMed

Henríquez, Francisco Cutanda; Castrillón, Silvia Vargas

2008-03-15

Dose-volume histograms (DVHs) are a useful tool in state-of-the-art radiotherapy treatment planning, and it is essential to recognize their limitations. Even after a specific dose-calculation model is optimized, dose distributions computed by using treatment-planning systems are affected by several sources of uncertainty, such as algorithm limitations, measurement uncertainty in the data used to model the beam, and residual differences between measured and computed dose. This report presents a novel method to take them into account. To take into account the effect of associated uncertainties, a probabilistic approach using a new kind of histogram, a dose-expected volume histogram, is introduced. The expected value of the volume in the region of interest receiving an absorbed dose equal to or greater than a certain value is found by using the probability distribution of the dose at each point. A rectangular probability distribution is assumed for this point dose, and a formulation that accounts for uncertainties associated with point dose is presented for practical computations. This method is applied to a set of DVHs for different regions of interest, including 6 brain patients, 8 lung patients, 8 pelvis patients, and 6 prostate patients planned for intensity-modulated radiation therapy. Results show a greater effect on planning target volume coverage than in organs at risk. In cases of steep DVH gradients, such as planning target volumes, this new method shows the largest differences with the corresponding DVH; thus, the effect of the uncertainty is larger.

Using CSLD Method to Calculate COD Pollution Load of Wei River Watershed above Huaxian Section, China

NASA Astrophysics Data System (ADS)

Zhu, Lei; Song, JinXi; Liu, WanQing

2017-12-01

Huaxian Section is the last hydrological and water quality monitoring section of Weihe River Watershed. Weihe River Watershed above Huaxian Section is taken as the research objective in this paper and COD is chosen as the water quality parameter. According to the discharge characteristics of point source pollutions and non-point source pollutions, a new method to estimate pollution loads—characteristic section load(CSLD) method is suggested and point source pollution and non-point source pollution loads of Weihe River Watershed above Huaxian Section are calculated in the rainy, normal and dry season in the year 2007. The results show that the monthly point source pollution loads of Weihe River Watershed above Huaxian Section discharge stably and the monthly non-point source pollution loads of Weihe River Watershed above Huaxian Section change greatly and the non-point source pollution load proportions of total pollution load of COD decrease in the normal, rainy and wet period in turn.

Calculating NH3-N pollution load of wei river watershed above Huaxian section using CSLD method

NASA Astrophysics Data System (ADS)

Zhu, Lei; Song, JinXi; Liu, WanQing

2018-02-01

Huaxian Section is the last hydrological and water quality monitoring section of Weihe River Watershed. So it is taken as the research objective in this paper and NH3-N is chosen as the water quality parameter. According to the discharge characteristics of point source pollutions and non-point source pollutions, a new method to estimate pollution loads—characteristic section load (CSLD)method is suggested and point source pollution and non-point source pollution loads of Weihe River Watershed above Huaxian Section are calculated in the rainy, normal and dry season in the year 2007. The results show that the monthly point source pollution loads of Weihe River Watershed above Huaxian Section discharge stably and the monthly non-point source pollution loads of Weihe River Watershed above Huaxian Section change greatly. The non-point source pollution load proportions of total pollution load of NH3-N decrease in the normal, rainy and wet period in turn.

Source characteristics of the Fairview, OK, earthquake sequence and its relationship to industrial activities

NASA Astrophysics Data System (ADS)

Yeck, W. L.; Weingarten, M.; Benz, H.; McNamara, D. E.; Herrmann, R. B.; Rubinstein, J. L.; Earle, P. S.; Bergman, E.

2016-12-01

We characterize the spatio-temporal patterns of seismicity surrounding the February 13, 2016, Mw 5.1 Fairview, Oklahoma earthquake. This earthquake sequence accounts for the largest moment release in the central and eastern US since the November 06, 2011 Mw 5.6 Prague, OK earthquake sequence. To improve the location accuracy of the sequence and measure near-source ground motions, the United States Geological Survey (USGS) deployed eight seismometers and accelerometers in the epicentral region. With the added depth control from these stations, we show that earthquakes primarily occur in the Precambrian basement, at depths of 6-10 km below sea level. The Mw 5.1 mainshock, the largest event in the cluster, locates near the base of the seismicity. Relocated aftershocks delineate a partially unmapped, 14-km-long fault segment that strikes approximately N40°E, partially bridging the gap between previously mapped basement faults to the southwest and northeast. Gas production and hydraulic fracking data from the region show no evidence that either of these activities correlates spatio-temporally with the Fairview sequence. Instead, we suggest that a series of high-rate, Arbuckle injection wells (> 300,000 bbls/month) 8-25 km northeast of this sequence pressurized the reservoir in the far field. Regional injection into the Arbuckle formation increased 7-fold in the 24 months before the initiation of the sequence with some wells operating at rates greater than 1 million barrels per month. Seismicity in the proximity of the high-rate wells is diffuse whilst the energetic Fairview sequence occurs more than 15 km from this region. Our observations point to the critical role pre-existing geologic structures play in the occurrence of large induced earthquakes. This study demonstrates the need for a better understanding of the role of far-field pressurization. High-quality data sets such as this facilitate the USGS mission to improve earthquake hazard identification, especially as related to induced earthquakes.

Managing agricultural phosphorus for water quality: lessons from the USA and China.

PubMed

Sharpley, Andrew; Wang, Xiaoyan

2014-09-01

The accelerated eutrophication of freshwaters and to a lesser extent some coastal waters is primarily driven by phosphorus (P) inputs. While efforts to identify and limit point source inputs of P to surface waters have seen some success, nonpoint sources remain difficult to identify, target, and remediate. As further improvements in wastewater treatment technologies becomes increasingly costly, attention has focused more on nonpoint source reduction, particularly the role of agriculture. This attention was heightened over the last 10 to 20 years by a number of highly visible cases of nutrient-related water quality degradation; including the Lake Taihu, Baltic Sea, Chesapeake Bay, and Gulf of Mexico. Thus, there has been a shift to targeted management of critical sources of P loss. In both the U.S. and China, there has been an intensification of agricultural production systems in certain areas concentrate large amounts of nutrients in excess of local crop and forage needs, which has increased the potential for P loss from these areas. To address this, innovative technologies are emerging that recycle water P back to land as fertilizer. For example, in the watershed of Lake Taihu, China one of the largest surface fresh waters for drinking water supply in China, local governments have encouraged innovation and various technical trials to harvest harmful algal blooms and use them for bio-gas, agricultural fertilizers, and biofuel production. In any country, however, the economics of remediation will remain a key limitation to substantial changes in agricultural production. Copyright © 2014. Published by Elsevier B.V.

Source apportionment and heavy metal health risk (HMHR) quantification from sources in a southern city in China, using an ME2-HMHR model.

PubMed

Peng, Xing; Shi, GuoLiang; Liu, GuiRong; Xu, Jiao; Tian, YingZe; Zhang, YuFen; Feng, YinChang; Russell, Armistead G

2017-02-01

Heavy metals (Cr, Co, Ni, As, Cd, and Pb) can be bound to PM adversely affecting human health. Quantifying the source impacts on heavy metals can provide source-specific estimates of the heavy metal health risk (HMHR) to guide effective development of strategies to reduce such risks from exposure to heavy metals in PM 2.5 (particulate matter (PM) with aerodynamic diameter less than or equal to 2.5 μm). In this study, a method combining Multilinear Engine 2 (ME2) and a risk assessment model is developed to more effectively quantify source contributions to HMHR, including heavy metal non-cancer risk (non-HMCR) and cancer risk (HMCR). The combined model (called ME2-HMHR) has two steps: step1, source contributions to heavy metals are estimated by employing the ME2 model; step2, the source contributions in step 1 are introduced into the risk assessment model to calculate the source contributions to HMHR. The approach was applied to Huzou, China and five significant sources were identified. Soil dust is the largest source of non-HMCR. For HMCR, the source contributions of soil dust, coal combustion, cement dust, vehicle, and secondary sources are 1.0 × 10 -4 , 3.7 × 10 -5 , 2.7 × 10 -6 , 1.6 × 10 -6 and 1.9 × 10 -9 , respectively. The soil dust is the largest contributor to HMCR, being driven by the high impact of soil dust on PM 2.5 and the abundance of heavy metals in soil dust. Copyright © 2016 Elsevier Ltd. All rights reserved.

Nutrient Status and Criteria Development for the Saint John River, Canada, Using a Weight of Evidence Approach

NASA Astrophysics Data System (ADS)

Culp, J. M.; Luiker, E. A.; Noel, L.; Curry, A. R.; Hryn, D.; Heard, K.

2005-05-01

The Saint John River is the largest in Maine/New Brunswick (673 km in length, draining 55,000 km2) with a history of natural resource use and nutrient effluent release to the watershed since the late 17th century. Our objective was to obtain a basic understanding of the contemporary nutrient conditions of the non-tidal portion of the river in relation to historical conditions, and to consider how the contemporary river is affected by point and non-point source nutrient loadings. The study included review of historical provincial and federal water quality databases dating back to the 1960s. Current water quality monitoring programs have focused on nitrogen (nitrite, nitrate, ammonia, TKN), phosphorus (total, dissolved, and soluble reactive phosphorus), DIC/DOC, and biomass of periphyton and phytoplankton. To determine nutrient limitation, nutrient diffusing substrate studies were conducted in river reaches of known nutrient enrichment. Oxygen stable isotopes were also used to provide information on the photosynthesis to respiration ratio. A weight of evidence approach combining the results of these studies was used to determine trophic status of river reaches and to highlight areas of eutrophication. From this information nutrient criteria for the Saint John River will be proposed.

Symptoms

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

Mercury in municipal solid wastes and New Jersey mercury prevention and reduction program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erdogan, H.; Stevenson, E.

1994-12-31

Mercury is a very toxic heavy metal which accumulates in the brain causing neurological damages involving psychasthenic and vegetative syndrome. At high exposure levels it causes behavioral and personality changes, loss of memory and insomnia. Long-term exposure or exposure during pregnancy to mercury or mercury compounds can permanently damage the kidney and fetus. In addition to potential effects on human health, mercury poisoning can also affect other living organisms. Mercury is different than other heavy metals. It consistently biomagnifies and bioaccumulates within the aquatic food chain. Global sources of mercury release are both natural and anthropogenic. Natural sources include volatilizationmore » of gaseous-mercury iron soils ana rocks, volcanic releases, evaporation from the ocean and other water bodies. Anthropogenic sources are fuel and coal combustion, mining, smelting, manufacturing activities, disposal of sludge, pesticides, animal and food waste, and incineration of municipal solid waste. Worldwide combustion of municipal solid waste is the second largest source of atmospheric emission of mercury. In New Jersey, incineration of solid waste is the largest source of atmospheric emission of mercury. The New Jersey Department of Environmental Protection and Energy (NJDEPE) has developed a comprehensive program to control and prevent emission of mercury resulting from combustion municipal solid waste.« less

Interaction Between the Celestial and the Terrestrial Reference Frames

NASA Technical Reports Server (NTRS)

Gordon, David; MacMillan, Dan; Bolotin, Sergei; Le Bail, Karine; Gipson, John; Ma, Chopo

2010-01-01

Effects of International Celestial Reference Frame (ICRF2) on the Terrestrial Reference Frames (TRF), CRF and EOP's, The ICRF2 became official on Jan. 1, 2010. It includes positions of 3414 compact radio astronomical sources observed with VLBI, a fivefold increase from the first ICRF. Numerous new VLBI models were used and the most unstable sources were treated as arc parameters to avoid distortions of the frame. The ICRF2 has a noise floor of 40 micro-arc-seconds and an axis stability of 10 micro-arc-seconds. It was aligned with the ICRS using 138 stable sources common to ICRF2 and ICRF-Ext2. Maintenance of ICRF2 is to be made using 295 defining sources chosen for their historical positional stability, minimal source structure, and sky distribution. Their stability and their more uniform sky distribution eliminate the two largest weaknesses of ICRF I. The switchover to ICRF2 has some small effects on the TRF, CRF and Earth Orientation Parameters (EOP). A CRF based on ICRF2 shows a relative rotation of 40 micro-arc-seconds, mostly about the Y-axis. Small shifts are also seen in the EOP's, the largest being 11 micro-arc-seconds in X-pole. Some small but insignificant differences are also seen in the TRF. These results will be presented and discussed.

Shellfish Allergy

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

Sulfate Aerosol in the Arctic: Source Attribution and Radiative Forcing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Yang; Wang, Hailong; Smith, Steven J.

Source attributions of Arctic sulfate and its direct radiative effect for 2010–2014 are quantified in this study using the Community Earth System Model (CESM) equipped with an explicit sulfur source-tagging technique. Regions that have high emissions and/or are near/within the Arctic present relatively large contributions to Arctic sulfate burden, with the largest contribution from sources in East Asia (27%). East Asia and South Asia together have the largest contributions to Arctic sulfate concentrations at 9–12 km, whereas sources within or near the Arctic account largely below 2 km. For remote sources with strong emissions, their contributions to Arctic sulfate burdenmore » are primarily driven by meteorology, while contributions of sources within or near the Arctic are dominated by their emission strength. The sulfate direct radiative effect (DRE) is –0.080 W m-2 at the Arctic surface, offsetting the net warming effect from the combination of in-snow heating and DRE cooling from black carbon. East Asia, Arctic local and Russia/Belarus/Ukraine sources contribute –0.017, –0.016 and –0.014 W m-2, respectively, to Arctic sulfate DRE. A 20% reduction in anthropogenic SO2 emissions leads to a net increase of +0.013 W m-2 forcing at the Arctic surface. These results indicate that a joint reduction in BC emissions could prevent possible Arctic warming from future reductions in SO2 emissions. Sulfate DRE efficiency calculations suggest that short transport pathways together with meteorology favoring long sulfate lifetimes make certain sources more efficient in influencing the Arctic sulfate DRE.« less

Large contribution of natural aerosols to uncertainty in indirect forcing

NASA Astrophysics Data System (ADS)

Carslaw, K. S.; Lee, L. A.; Reddington, C. L.; Pringle, K. J.; Rap, A.; Forster, P. M.; Mann, G. W.; Spracklen, D. V.; Woodhouse, M. T.; Regayre, L. A.; Pierce, J. R.

2013-11-01

The effect of anthropogenic aerosols on cloud droplet concentrations and radiative properties is the source of one of the largest uncertainties in the radiative forcing of climate over the industrial period. This uncertainty affects our ability to estimate how sensitive the climate is to greenhouse gas emissions. Here we perform a sensitivity analysis on a global model to quantify the uncertainty in cloud radiative forcing over the industrial period caused by uncertainties in aerosol emissions and processes. Our results show that 45 per cent of the variance of aerosol forcing since about 1750 arises from uncertainties in natural emissions of volcanic sulphur dioxide, marine dimethylsulphide, biogenic volatile organic carbon, biomass burning and sea spray. Only 34 per cent of the variance is associated with anthropogenic emissions. The results point to the importance of understanding pristine pre-industrial-like environments, with natural aerosols only, and suggest that improved measurements and evaluation of simulated aerosols in polluted present-day conditions will not necessarily result in commensurate reductions in the uncertainty of forcing estimates.

Higgs bosons with large transverse momentum at the LHC

NASA Astrophysics Data System (ADS)

Kudashkin, Kirill; Lindert, Jonas M.; Melnikov, Kirill; Wever, Christopher

2018-07-01

We compute the next-to-leading order QCD corrections to the production of Higgs bosons with large transverse momentum p⊥ ≫ 2mt at the LHC. To accomplish this, we combine the two-loop amplitudes for processes gg → Hg, qg → Hq and q q bar → Hg, recently computed in the approximation of nearly massless top quarks, with the numerical calculation of the squared one-loop amplitudes for gg → Hgg, qg → Hqg and q q bar → Hgg processes. The latter computation is performed with OpenLoops. We find that the QCD corrections to the Higgs transverse momentum distribution at very high p⊥ are large but quite similar to the QCD corrections obtained for point-like Hgg coupling. Our result removes one of the largest sources of theoretical uncertainty in the description of high-p⊥ Higgs boson production and opens a way to use the high-p⊥ region to search for physics beyond the Standard Model.

Extreme Mg-26 and O-17 enrichments in an Orgueil corundum: Identification of a presolar oxide grain

NASA Technical Reports Server (NTRS)

Hutcheon, I. D.; Huss, G. R.; Fahey, A. J.; Wasserburg, G. J.

1994-01-01

A corundum (Al2O3) grain from the Orgueil meteorite is greatly enriched in O-17 and (Mg-26)(sup *). The measured O-16/O-17 is 1028 +/- 11 compared to solar(O-16/O-17) = 2610. This is the largest O-17 excess so far observed in any meteoritic material. The Mg-26 excess ((Mg-26)(sup *)) is most plausibly due to in situ decay of Al-26. The inferred (Al-26/Al-27)(sub 0) ratio of 8.9 x 10(exp -4) is approximately 18 times larger than the 5 x 10(exp -5) value commonly observed in refractory inclusions formed in the solar system. The large O-17 excess and high (Mg-26)(sup *) Al-27 ratio unambiguously identify this corundum as a presolar oxide grain. Enrichments in O-17 and Al-26 are characteristic of H-burning and point to red giant or asymptotic giant branch (AGB) stars as likely sources.

Nepalese origin of cholera epidemic in Haiti.

PubMed

Frerichs, R R; Keim, P S; Barrais, R; Piarroux, R

2012-06-01

Cholera appeared in Haiti in October 2010 for the first time in recorded history. The causative agent was quickly identified by the Haitian National Public Health Laboratory and the United States Centers for Disease Control and Prevention as Vibrio cholerae serogroup O1, serotype Ogawa, biotype El Tor. Since then, >500 000 government-acknowledged cholera cases and >7000 deaths have occurred, the largest cholera epidemic in the world, with the real death toll probably much higher. Questions of origin have been widely debated with some attributing the onset of the epidemic to climatic factors and others to human transmission. None of the evidence on origin supports climatic factors. Instead, recent epidemiological and molecular-genetic evidence point to the United Nations peacekeeping troops from Nepal as the source of cholera to Haiti, following their troop rotation in early October 2010. Such findings have important policy implications for shaping future international relief efforts. © 2012 The Authors. Clinical Microbiology and Infection © 2012 European Society of Clinical Microbiology and Infectious Diseases.

Middle Palaeolithic and Neolithic Occupations around Mundafan Palaeolake, Saudi Arabia: Implications for Climate Change and Human Dispersals

PubMed Central

Crassard, Rémy; Petraglia, Michael D.; Drake, Nick A.; Breeze, Paul; Gratuze, Bernard; Alsharekh, Abdullah; Arbach, Mounir; Groucutt, Huw S.; Khalidi, Lamya; Michelsen, Nils; Robin, Christian J.; Schiettecatte, Jérémie

2013-01-01

The Arabian Peninsula is a key region for understanding climate change and human occupation history in a marginal environment. The Mundafan palaeolake is situated in southern Saudi Arabia, in the Rub’ al-Khali (the ‘Empty Quarter’), the world’s largest sand desert. Here we report the first discoveries of Middle Palaeolithic and Neolithic archaeological sites in association with the palaeolake. We associate the human occupations with new geochronological data, and suggest the archaeological sites date to the wet periods of Marine Isotope Stage 5 and the Early Holocene. The archaeological sites indicate that humans repeatedly penetrated the ameliorated environments of the Rub’ al-Khali. The sites probably represent short-term occupations, with the Neolithic sites focused on hunting, as indicated by points and weaponry. Middle Palaeolithic assemblages at Mundafan support a lacustrine adaptive focus in Arabia. Provenancing of obsidian artifacts indicates that Neolithic groups at Mundafan had a wide wandering range, with transport of artifacts from distant sources. PMID:23894519

Middle palaeolithic and neolithic occupations around Mundafan Palaeolake, Saudi Arabia: implications for climate change and human dispersals.

PubMed

Crassard, Rémy; Petraglia, Michael D; Drake, Nick A; Breeze, Paul; Gratuze, Bernard; Alsharekh, Abdullah; Arbach, Mounir; Groucutt, Huw S; Khalidi, Lamya; Michelsen, Nils; Robin, Christian J; Schiettecatte, Jérémie

2013-01-01

The Arabian Peninsula is a key region for understanding climate change and human occupation history in a marginal environment. The Mundafan palaeolake is situated in southern Saudi Arabia, in the Rub' al-Khali (the 'Empty Quarter'), the world's largest sand desert. Here we report the first discoveries of Middle Palaeolithic and Neolithic archaeological sites in association with the palaeolake. We associate the human occupations with new geochronological data, and suggest the archaeological sites date to the wet periods of Marine Isotope Stage 5 and the Early Holocene. The archaeological sites indicate that humans repeatedly penetrated the ameliorated environments of the Rub' al-Khali. The sites probably represent short-term occupations, with the Neolithic sites focused on hunting, as indicated by points and weaponry. Middle Palaeolithic assemblages at Mundafan support a lacustrine adaptive focus in Arabia. Provenancing of obsidian artifacts indicates that Neolithic groups at Mundafan had a wide wandering range, with transport of artifacts from distant sources.

Investigation of a Q fever outbreak in a Scottish co-located slaughterhouse and cutting plant.

PubMed

Wilson, L E; Couper, S; Prempeh, H; Young, D; Pollock, K G J; Stewart, W C; Browning, L M; Donaghy, M

2010-12-01

Outbreaks of Q fever are rare in the UK. In 2006, the largest outbreak of Q fever in Scotland occurred at a co-located slaughterhouse and cutting plant with 110 cases. Preliminary investigations pointed to the sheep lairage being the potential source of exposure to the infective agent. A retrospective cohort study was carried out among workers along with environmental sampling to guide public health interventions. A total of 179 individuals were interviewed of whom 66 (37%) were migrant workers. Seventy-five (41.9%) were serologically confirmed cases. Passing through a walkway situated next to the sheep lairage, a nearby stores area, and being male were independently associated with being serologically positive for Q fever. The large proportion of migrant workers infected presented a significant logistical problem during outbreak investigation and follow up. The topic of vaccination against Q fever for slaughterhouse workers is contentious out with Australasia, but this outbreak highlights important occupational health issues. © 2009 Blackwell Verlag GmbH.

Guidelines for the standardization of preanalytic variables for blood-based biomarker studies in Alzheimer’s disease research

PubMed Central

Gupta, Veer; Henriksen, Kim; Edwards, Melissa; Jeromin, Andreas; Lista, Simone; Bazenet, Chantal; Soares, Holly; Lovestone, Simon; Hampel, Harald; Montine, Thomas; Blennow, Kaj; Foroud, Tatiana; Carrillo, Maria; Graff-Radford, Neill; Laske, Christoph; Breteler, Monique; Shaw, Leslie; Trojanowski, John Q.; Schupf, Nicole; Rissman, Robert A.; Fagan, Anne M.; Oberoi, Pankaj; Umek, Robert; Weiner, Michael W.; Grammas, Paula; Posner, Holly; Martins, Ralph

2015-01-01

The lack of readily available biomarkers is a significant hindrance towards progressing to effective therapeutic and preventative strategies for Alzheimer’s disease (AD). Blood-based biomarkers have potential to overcome access and cost barriers and greatly facilitate advanced neuroimaging and cerebrospinal fluid biomarker approaches. Despite the fact that preanalytical processing is the largest source of variability in laboratory testing, there are no currently available standardized preanalytical guidelines. The current international working group provides the initial starting point for such guidelines for standardized operating procedures (SOPs). It is anticipated that these guidelines will be updated as additional research findings become available. The statement provides (1) a synopsis of selected preanalytical methods utilized in many international AD cohort studies, (2) initial draft guidelines/SOPs for preanalytical methods, and (3) a list of required methodological information and protocols to be made available for publications in the field in order to foster cross-validation across cohorts and laboratories. PMID:25282381

Atmospheric ammonia measurements at low concentration sites in the northeastern USA: implications for total nitrogen deposition and comparison with CMAQ estimates

EPA Science Inventory

We evaluated the relative importance of dry deposition of ammonia (NH3) gas at several headwater areas of the Susquehanna River, the largest single source of nitrogen pollution to Chesapeake Bay, including three that are remote from major sources of NH3 emissions (CTH, ARN, and K...

Watershed level examination of urea fate and transport and the production of the biotoxin domoic acid

USDA-ARS?s Scientific Manuscript database

The Chesapeake Bay, the largest estuary in the world, is an important source of many fish and shellfish. The safety of these species as a food source is currently at risk due to nutrient pollution. Urea, a form of organic nitrogen found in manure and fertilizer, is increasing in usage within the Ba...

Measuring and mitigating agricultural greenhouse gas production in the US Great Plains, 1870-2000.

PubMed

Parton, William J; Gutmann, Myron P; Merchant, Emily R; Hartman, Melannie D; Adler, Paul R; McNeal, Frederick M; Lutz, Susan M

2015-08-25

The Great Plains region of the United States is an agricultural production center for the global market and, as such, an important source of greenhouse gas (GHG) emissions. This article uses historical agricultural census data and ecosystem models to estimate the magnitude of annual GHG fluxes from all agricultural sources (e.g., cropping, livestock raising, irrigation, fertilizer production, tractor use) in the Great Plains from 1870 to 2000. Here, we show that carbon (C) released during the plow-out of native grasslands was the largest source of GHG emissions before 1930, whereas livestock production, direct energy use, and soil nitrous oxide emissions are currently the largest sources. Climatic factors mediate these emissions, with cool and wet weather promoting C sequestration and hot and dry weather increasing GHG release. This analysis demonstrates the long-term ecosystem consequences of both historical and current agricultural activities, but also indicates that adoption of available alternative management practices could substantially mitigate agricultural GHG fluxes, ranging from a 34% reduction with a 25% adoption rate to as much as complete elimination with possible net sequestration of C when a greater proportion of farmers adopt new agricultural practices.

Measuring and mitigating agricultural greenhouse gas production in the US Great Plains, 1870–2000

PubMed Central

Parton, William J.; Gutmann, Myron P.; Merchant, Emily R.; Hartman, Melannie D.; Adler, Paul R.; McNeal, Frederick M.; Lutz, Susan M.

2015-01-01

The Great Plains region of the United States is an agricultural production center for the global market and, as such, an important source of greenhouse gas (GHG) emissions. This article uses historical agricultural census data and ecosystem models to estimate the magnitude of annual GHG fluxes from all agricultural sources (e.g., cropping, livestock raising, irrigation, fertilizer production, tractor use) in the Great Plains from 1870 to 2000. Here, we show that carbon (C) released during the plow-out of native grasslands was the largest source of GHG emissions before 1930, whereas livestock production, direct energy use, and soil nitrous oxide emissions are currently the largest sources. Climatic factors mediate these emissions, with cool and wet weather promoting C sequestration and hot and dry weather increasing GHG release. This analysis demonstrates the long-term ecosystem consequences of both historical and current agricultural activities, but also indicates that adoption of available alternative management practices could substantially mitigate agricultural GHG fluxes, ranging from a 34% reduction with a 25% adoption rate to as much as complete elimination with possible net sequestration of C when a greater proportion of farmers adopt new agricultural practices. PMID:26240366

Above- and below-ground methane fluxes and methanotrophic activity in a landfill-cover soil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schroth, M.H., E-mail: martin.schroth@env.ethz.ch; Eugster, W.; Gomez, K.E.

2012-05-15

Highlights: Black-Right-Pointing-Pointer We quantify above- and below-ground CH{sub 4} fluxes in a landfill-cover soil. Black-Right-Pointing-Pointer We link methanotrophic activity to estimates of CH{sub 4} loading from the waste body. Black-Right-Pointing-Pointer Methane loading and emissions are highly variable in space and time. Black-Right-Pointing-Pointer Eddy covariance measurements yield largest estimates of CH{sub 4} emissions. Black-Right-Pointing-Pointer Potential methanotrophic activity is high at a location with substantial CH{sub 4} loading. - Abstract: Landfills are a major anthropogenic source of the greenhouse gas methane (CH{sub 4}). However, much of the CH{sub 4} produced during the anaerobic degradation of organic waste is consumed by methanotrophic microorganismsmore » during passage through the landfill-cover soil. On a section of a closed landfill near Liestal, Switzerland, we performed experiments to compare CH{sub 4} fluxes obtained by different methods at or above the cover-soil surface with below-ground fluxes, and to link methanotrophic activity to estimates of CH{sub 4} ingress (loading) from the waste body at selected locations. Fluxes of CH{sub 4} into or out of the cover soil were quantified by eddy-covariance and static flux-chamber measurements. In addition, CH{sub 4} concentrations at the soil surface were monitored using a field-portable FID detector. Near-surface CH{sub 4} fluxes and CH{sub 4} loading were estimated from soil-gas concentration profiles in conjunction with radon measurements, and gas push-pull tests (GPPTs) were performed to quantify rates of microbial CH{sub 4} oxidation. Eddy-covariance measurements yielded by far the largest and probably most representative estimates of overall CH{sub 4} emissions from the test section (daily mean up to {approx}91,500 {mu}mol m{sup -2} d{sup -1}), whereas flux-chamber measurements and CH{sub 4} concentration profiles indicated that at the majority of locations the cover soil was a net sink for atmospheric CH{sub 4} (uptake up to -380 {mu}mol m{sup -2} d{sup -1}) during the experimental period. Methane concentration profiles also indicated strong variability in CH{sub 4} loading over short distances in the cover soil, while potential methanotrophic activity derived from GPPTs was high (v{sub max} {approx} 13 mmol L{sup -1}(soil air) h{sup -1}) at a location with substantial CH{sub 4} loading. Our results provide a basis to assess spatial and temporal variability of CH{sub 4} dynamics in the complex terrain of a landfill-cover soil.« less

Taking Care of Yourself

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

Living Well Everyday

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

Treatment and Managing Reactions

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

Apertured averaged scintillation of fully and partially coherent Gaussian, annular Gaussian, flat toped and dark hollow beams

NASA Astrophysics Data System (ADS)

Eyyuboğlu, Halil T.

2015-03-01

Apertured averaged scintillation requires the evaluation of rather complicated irradiance covariance function. Here we develop a much simpler numerical method based on our earlier introduced semi-analytic approach. Using this method, we calculate aperture averaged scintillation of fully and partially coherent Gaussian, annular Gaussian flat topped and dark hollow beams. For comparison, the principles of equal source beam power and normalizing the aperture averaged scintillation with respect to received power are applied. Our results indicate that for fully coherent beams, upon adjusting the aperture sizes to capture 10 and 20% of the equal source power, Gaussian beam needs the largest aperture opening, yielding the lowest aperture average scintillation, whilst the opposite occurs for annular Gaussian and dark hollow beams. When assessed on the basis of received power normalized aperture averaged scintillation, fixed propagation distance and aperture size, annular Gaussian and dark hollow beams seem to have the lowest scintillation. Just like the case of point-like scintillation, partially coherent beams will offer less aperture averaged scintillation in comparison to fully coherent beams. But this performance improvement relies on larger aperture openings. Upon normalizing the aperture averaged scintillation with respect to received power, fully coherent beams become more advantageous than partially coherent ones.

Measurements and source apportionment of particle-associated polycyclic aromatic hydrocarbons in ambient air in Riyadh, Saudi Arabia

NASA Astrophysics Data System (ADS)

Bian, Qijing; Alharbi, Badr; Collett, Jeffrey; Kreidenweis, Sonia; Pasha, Mohammad J.

2016-07-01

Ambient air samples were obtained in Riyadh, the capital and largest city of Saudi Arabia, during two measurement campaigns spanning September 2011 to September 2012. Sixteen particle-phase polycyclic aromatic hydrocarbons (PAH) were quantified in 167 samples. Pyrene and fluoranthene were the most abundant PAH, with average of 3.37 ± 14.01 ng m-3 and 8.00 ± 44.09 ng m-3, respectively. A dominant contribution from low molecular weight (LMW) PAH (MW < 228) suggested a large influence of industrial emissions on PAH concentrations. Monte Carlo source apportionment using diagnostic ratios showed that 80 ± 10% of the average LMW PAH concentrations were contributed by petroleum vapor emissions, while 53 ± 19% of high molecular weight (HMW) PAH were from solid fuel combustion emissions. The positive matrix factorization model estimated that oil combustion emissions dominated total PAH concentrations, accounting for on average 96%, likely due to widespread use of oil fuels in energy production (power plants and industries). Our results demonstrate the significant influence of petroleum product production and consumption on particulate-phase PAH concentrations in Riyadh, but also point to the importance of traffic and solid fuel burning, including coke burning and seasonal biomass burning, especially as they contribute to the ambient levels of HMW PAH.

The Taurus Spitzer Legacy Project

NASA Astrophysics Data System (ADS)

McCabe, Caer-Eve; Padgett, D. L.; Rebull, L.; Noriega-Crespo, A.; Carey, S.; Brooke, T.; Stapelfeldt, K. R.; Fukagawa, M.; Hines, D.; Terebey, S.; Huard, T.; Hillenbrand, L.; Guedel, M.; Audard, M.; Monin, J.; Guieu, S.; Knapp, G.; Evans, N. J., III; Menard, F.; Harvey, P.; Allen, L.; Wolf, S.; Skinner, S.; Strom, S.; Glauser, A.; Saavedra, C.; Koerner, D.; Myers, P.; Shupe, D.; Latter, W.; Grosso, N.; Heyer, M.; Dougados, C.; Bouvier, J.

2009-01-01

Without massive stars and dense stellar clusters, Taurus plays host to a distributed mode of low-mass star formation particularly amenable to observational and theoretical study. In 2005-2007, our team mapped the central 43 square degrees of the main Taurus clouds at wavelengths from 3.6 - 160 microns with the IRAC and MIPS cameras on the Spitzer Space Telescope. Together, these images form the largest contiguous Spitzer map of a single star-forming region (and any region outside the galactic plane). Our Legacy team has generated re-reduced mosaic images and source catalogs, available to the community via the Spitzer Science Center website http://ssc.spitzer.caltech.edu/legacy/all.html . This Spitzer survey is a central and crucial part of a multiwavelength study of the Taurus cloud complex that we have performed using XMM, CFHT, and the SDSS. The seven photometry data points from Spitzer allow us to characterize the circumstellar environment of each object, and, in conjunction with optical and NIR photometry, construct a complete luminosity function for the cloud members that will place constraints on the initial mass function. We present results drawing upon our catalog of several hundred thousand IRAC and thousands of MIPS sources. Initial results from our study of the Taurus clouds include new disks around brown dwarfs, new low luminosity YSO candidates, and new Herbig-Haro objects.

Interferometry with flexible point source array for measuring complex freeform surface and its design algorithm

NASA Astrophysics Data System (ADS)

Li, Jia; Shen, Hua; Zhu, Rihong; Gao, Jinming; Sun, Yue; Wang, Jinsong; Li, Bo

2018-06-01

The precision of the measurements of aspheric and freeform surfaces remains the primary factor restrict their manufacture and application. One effective means of measuring such surfaces involves using reference or probe beams with angle modulation, such as tilted-wave-interferometer (TWI). It is necessary to improve the measurement efficiency by obtaining the optimum point source array for different pieces before TWI measurements. For purpose of forming a point source array based on the gradients of different surfaces under test, we established a mathematical model describing the relationship between the point source array and the test surface. However, the optimal point sources are irregularly distributed. In order to achieve a flexible point source array according to the gradient of test surface, a novel interference setup using fiber array is proposed in which every point source can be independently controlled on and off. Simulations and the actual measurement examples of two different surfaces are given in this paper to verify the mathematical model. Finally, we performed an experiment of testing an off-axis ellipsoidal surface that proved the validity of the proposed interference system.

Nutrient sources and transport in the Missouri River Basin, with emphasis on the effects of irrigation and reservoirs

USGS Publications Warehouse

Brown, J.B.; Sprague, L.A.; Dupree, J.A.

2011-01-01

SPAtially Referenced Regressions On Watershed attributes (SPARROW) models were used to relate instream nutrient loads to sources and factors influencing the transport of nutrients in the Missouri River Basin. Agricultural inputs from fertilizer and manure were the largest nutrient sources throughout a large part of the basin, although atmospheric and urban inputs were important sources in some areas. Sediment mobilized from stream channels was a source of phosphorus in medium and larger streams. Irrigation on agricultural land was estimated to decrease the nitrogen load reaching the Mississippi River by as much as 17%, likely as a result of increased anoxia and denitrification in the soil zone. Approximately 16% of the nitrogen load and 33% of the phosphorus load that would have otherwise reached the Mississippi River was retained in reservoirs and lakes throughout the basin. Nearly half of the total attenuation occurred in the eight largest water bodies. Unlike the other major tributary basins, nearly the entire instream nutrient load leaving the outlet of the Platte and Kansas River subbasins reached the Mississippi River. Most of the larger reservoirs and lakes in the Platte River subbasin are upstream of the major sources, whereas in the Kansas River subbasin, most of the source inputs are in the southeast part of the subbasin where characteristics of the area and proximity to the Missouri River facilitate delivery of nutrients to the Mississippi River.

County-level estimates of nutrient inputs to the landsurface of the conterminous United States, 1982-2001

USGS Publications Warehouse

Ruddy, Barbara C.; Lorenz, David L.; Mueller, David K.

2006-01-01

Nutrient input data for fertilizer use, livestock manure, and atmospheric deposition from various sources were estimated and allocated to counties in the conterminous United States for the years 1982 through 2001. These nationally consistent nutrient input data are needed by the National Water-Quality Assessment Program for investigations of stream- and ground-water quality. For nitrogen, the largest source was farm fertilizer; for phosphorus, the largest sources were farm fertilizer and livestock manure. Nutrient inputs from fertilizer use in nonfarm areas, while locally important, were an order of magnitude smaller than inputs from other sources. Nutrient inputs from all sources increased between 1987 and 1997, but the relative proportions of nutrients from each source were constant. Farm-fertilizer inputs were highest in the upper Midwest, along eastern coastal areas, and in irrigated areas of the West. Nonfarm-fertilizer use was similar in major metropolitan areas throughout the Nation, but was more extensive in the more populated Eastern and Central States and in California. Areas of greater manure inputs were located throughout the South-central and Southeastern States and in scattered areas of the West. Nitrogen deposition from the atmosphere generally increased from west to east and is related to the location of major sources and the effects of precipitation and prevailing winds. These nutrient-loading data at the county level are expected to be the fundamental basis for national and regional assessments of water quality for the National Water-Quality Assessment Program and other large-scale programs.

Nutrient Sources and Transport in the Missouri River Basin, with Emphasis on the Effects of Irrigation and Reservoirs1

PubMed Central

Brown, Juliane B; Sprague, Lori A; Dupree, Jean A

2011-01-01

Abstract SPAtially Referenced Regressions On Watershed attributes (SPARROW) models were used to relate instream nutrient loads to sources and factors influencing the transport of nutrients in the Missouri River Basin. Agricultural inputs from fertilizer and manure were the largest nutrient sources throughout a large part of the basin, although atmospheric and urban inputs were important sources in some areas. Sediment mobilized from stream channels was a source of phosphorus in medium and larger streams. Irrigation on agricultural land was estimated to decrease the nitrogen load reaching the Mississippi River by as much as 17%, likely as a result of increased anoxia and denitrification in the soil zone. Approximately 16% of the nitrogen load and 33% of the phosphorus load that would have otherwise reached the Mississippi River was retained in reservoirs and lakes throughout the basin. Nearly half of the total attenuation occurred in the eight largest water bodies. Unlike the other major tributary basins, nearly the entire instream nutrient load leaving the outlet of the Platte and Kansas River subbasins reached the Mississippi River. Most of the larger reservoirs and lakes in the Platte River subbasin are upstream of the major sources, whereas in the Kansas River subbasin, most of the source inputs are in the southeast part of the subbasin where characteristics of the area and proximity to the Missouri River facilitate delivery of nutrients to the Mississippi River. PMID:22457581

Nitrate in aquifers beneath agricultural systems

USGS Publications Warehouse

Burkart, M.R.; Stoner, J.D.; ,

2007-01-01

Research from several regions of the world provides spatially anecdotal evidence to hypothesize which hydrologic and agricultural factors contribute to groundwater vulnerability to nitrate contamination. Analysis of nationally consistent measurements from the U.S. Geological Survey's NAWQA program confirms these hypotheses for a substantial range of agricultural systems. Shallow unconfined aquifers are most susceptible to nitrate contamination associated with agricultural systems. Alluvial and other unconsolidated aquifers are the most vulnerable and also shallow carbonate aquifers that provide a substantial but smaller contamination risk. Where any of these aquifers are overlain by permeable soils the risk of contamination is larger. Irrigated systems can compound this vulnerability by increasing leaching facilitated by additional recharge and additional nutrient applications. The system of corn, soybean, and hogs produced significantly larger concentrations of groundwater nitrate than all other agricultural systems because this system imports the largest amount of N-fertilizer per unit production area. Mean nitrate under dairy, poultry, horticulture, and cattle and grains systems were similar. If trends in the relation between increased fertilizer use and groundwater nitrate in the United States are repeated in other regions of the world, Asia may experience increasing problems because of recent increases in fertilizer use. Groundwater monitoring in Western and Eastern Europe as well as Russia over the next decade may provide data to determine if the trend in increased nitrate contamination can be reversed. If the concentrated livestock trend in the United States is global, it may be accompanied by increasing nitrogen contamination in groundwater. Concentrated livestock provide both point sources in the confinement area and intense non-point sources as fields close to facilities are used for manure disposal. Regions where irrigated cropland is expanding, such as in Asia, may experience the greatest impact of this practice on groundwater nitrate. ?? USDA 2007.

Connecting smoke plumes to sources using Hazard Mapping System (HMS) smoke and fire location data over North America

NASA Astrophysics Data System (ADS)

Brey, Steven J.; Ruminski, Mark; Atwood, Samuel A.; Fischer, Emily V.

2018-02-01

Fires represent an air quality challenge because they are large, dynamic and transient sources of particulate matter and ozone precursors. Transported smoke can deteriorate air quality over large regions. Fire severity and frequency are likely to increase in the future, exacerbating an existing problem. Using the National Environmental Satellite, Data, and Information Service (NESDIS) Hazard Mapping System (HMS) smoke data for North America for the period 2007 to 2014, we examine a subset of fires that are confirmed to have produced sufficient smoke to warrant the initiation of a U.S. National Weather Service smoke forecast. We find that gridded HMS-analyzed fires are well correlated (r = 0.84) with emissions from the Global Fire Emissions Inventory Database 4s (GFED4s). We define a new metric, smoke hours, by linking observed smoke plumes to active fires using ensembles of forward trajectories. This work shows that the Southwest, Northwest, and Northwest Territories initiate the most air quality forecasts and produce more smoke than any other North American region by measure of the number of HYSPLIT points analyzed, the duration of those HYSPLIT points, and the total number of smoke hours produced. The average number of days with smoke plumes overhead is largest over the north-central United States. Only Alaska, the Northwest, the Southwest, and Southeast United States regions produce the majority of smoke plumes observed over their own borders. This work moves a new dataset from a daily operational setting to a research context, and it demonstrates how changes to the frequency or intensity of fires in the western United States could impact other regions.

A protozoal-associated epizootic impacting marine wildlife: Mass-mortality of southern sea otters (Enhydra lutris nereis) due to Sarcocystis neurona infection

USGS Publications Warehouse

Miller, M.A.; Conrad, P.A.; Harris, M.; Hatfield, B.; Langlois, G.; Jessup, David A.; Magargal, S.L.; Packham, A.E.; Toy-Choutka, S.; Melli, A.C.; Murray, M.A.; Gulland, F.M.; Grigg, M.E.

2010-01-01

During April 2004, 40 sick and dead southern sea otters (Enhydra lutris nereis) were recovered over 18 km of coastline near Morro Bay, California. This event represented the single largest monthly spike in mortality ever recorded during 30 years of southern sea otter stranding data collection. Because of the point-source nature of the event and clinical signs consistent with severe, acute neurological disease, exposure to a chemical or marine toxin was initially considered. However, detailed postmortem examinations revealed lesions consistent with an infectious etiology, and further investigation confirmed the protozoan parasite Sarcocystis neurona as the underlying cause. Tissues from 94% of examined otters were PCR-positive for S. neurona, based on DNA amplification and sequencing at the ITS-1 locus, and 100% of tested animals (n= 14) had elevated IgM and IgG titers to S. neurona. Evidence to support the point-source character of this event include the striking spatial and temporal clustering of cases and detection of high concentrations of anti- S. neurona IgM in serum of stranded animals. Concurrent exposure to the marine biotoxin domoic acid may have enhanced susceptibility of affected otters to S. neurona and exacerbated the neurological signs exhibited by stranded animals. Other factors that may have contributed to the severity of this epizootic include a large rainstorm that preceded the event and an abundance of razor clams near local beaches, attracting numerous otters close to shore within the affected area. This is the first report of a localized epizootic in marine wildlife caused by apicomplexan protozoa. ?? 2010 Elsevier B.V.

Temporal and Spatial Variability in the Partitioning and Flux of Riverine Iron Delivered to the Gulf of Alaska

NASA Astrophysics Data System (ADS)

Schroth, A. W.; Crusius, J.; Kroeger, K. D.; Hoyer, I. R.; Osburn, C. L.

2010-12-01

Iron (Fe) is a micronutrient that is thought to limit phytoplankton productivity in offshore waters of the Gulf of Alaska (GoA). However, it has been proposed that in coastal regions where offshore, Fe-limited, nitrate-rich waters mix with relatively Fe-rich river plumes, productive ecosystems and fisheries result. Indeed, an observed northward increase in phytoplankton biomass along the pacific coast of North America has been attributed to higher input of riverine Fe to coastal waters, suggesting that many of the coastal ecosystems of the North Pacific rely heavily on this input of Fe as a nutrient source. Based on our studies of the Copper River (the largest point source of freshwater to the GoA) and its tributaries, it is clear that riverine Fe delivered to the GoA is primarily derived from fine glacial flour generated by glacial weathering, which imparts a unique partitioning of Fe species and Fe size fractionation in coastal river plumes. Furthermore, the distribution of Fe species and size fractionation exhibits significant seasonal and spatial variability based on the source of iron within the watershed, which varies from glacial mechanical weathering of bedrock to internal chemical processing in portions of watersheds with forest and wetland land covers. These findings are relevant to our understanding of the GoA biogeochemical system as it exists today and can help to predict how the system may evolve as glaciers within the GoA watershed continue to recede.

Estimating the sources and transport of nutrients in the Waikato River Basin, New Zealand

USGS Publications Warehouse

Alexander, Richard B.; Elliott, Alexander H.; Shankar, Ude; McBride, Graham B.

2002-01-01

We calibrated SPARROW (Spatially Referenced Regression on Watershed Attributes) surface water‐quality models using measurements of total nitrogen and total phosphorus from 37 sites in the 13,900‐km2 Waikato River Basin, the largest watershed on the North Island of New Zealand. This first application of SPARROW outside of the United States included watersheds representative of a wide range of natural and cultural conditions and water‐resources data that were well suited for calibrating and validating the models. We applied the spatially distributed model to a drainage network of nearly 5000 stream reaches and 75 lakes and reservoirs to empirically estimate the rates of nutrient delivery (and their levels of uncertainty) from point and diffuse sources to streams, lakes, and watershed outlets. The resulting models displayed relatively small errors; predictions of stream yield (kg ha−1 yr−1) were typically within 30% or less of the observed values at the monitoring sites. There was strong evidence of the accuracy of the model estimates of nutrient sources and the natural rates of nutrient attenuation in surface waters. Estimated loss rates for streams, lakes, and reservoirs agreed closely with experimental measurements and empirical models from New Zealand, North America, and Europe as well as with previous U.S. SPARROW models. The results indicate that the SPARROW modeling technique provides a reliable method for relating experimental data and observations from small catchments to the transport of nutrients in the surface waters of large river basins.

Effects of Nitrogen Inputs and Watershed Characteristics on ...

EPA Pesticide Factsheets

Nitrogen (N) inputs to the landscape have been linked previously to N loads exported from watersheds at the national scale; however, stream N concentration is arguably more relevant than N load for drinking water quality, freshwater biological responses and establishment of nutrient criteria. In this study, we combine national-scale anthropogenic N input data, including synthetic fertilizer, crop biological N fixation, manure applied to farmland, atmospheric N deposition, and point source inputs, with data from the 2008-09 National Rivers and Streams Assessment to quantify the relationship between N inputs and in-stream concentrations of total N (TN), dissolved inorganic N (DIN), and total organic N (TON) (calculated as TN – DIN). In conjunction with simple linear regression, we use multiple regression to understand how watershed and stream reach attributes modify the effect of N inputs on N concentrations. Median TN was 0.50 mg N L-1 with a maximum of 25.8 mg N L-1. Total N inputs to the watershed ranged from less than 1 to 196 kg N ha-1 y-1, with a median of 14.4 kg N ha-1 y-1. Atmospheric N deposition was the single largest anthropogenic N source in the majority of sites, but, agricultural sources generally dominate total N inputs in sites with elevated N concentrations. The sum of all N inputs were positively correlated with concentrations of all forms of N [r2 = 0.44, 0.43, and 0.18 for TN, DIN, and TON, respectively (all log-transformed), n = 1112], indi

Changing Regulations of COD Pollution Load of Weihe River Watershed above TongGuan Section, China

NASA Astrophysics Data System (ADS)

Zhu, Lei; Liu, WanQing

2018-02-01

TongGuan Section of Weihe River Watershed is a provincial section between Shaanxi Province and Henan Province, China. Weihe River Watershed above TongGuan Section is taken as the research objective in this paper and COD is chosen as the water quality parameter. According to the discharge characteristics of point source pollutions and non-point source pollutions, a method—characteristic section load (CSLD) method is suggested and point and non-point source pollution loads of Weihe River Watershed above TongGuan Section are calculated in the rainy, normal and dry season in 2013. The results show that the monthly point source pollution loads of Weihe River Watershed above TongGuan Section discharge stably and the monthly non-point source pollution loads of Weihe River Watershed above TongGuan Section change greatly and the non-point source pollution load proportions of total pollution load of COD decrease in the rainy, wet and normal period in turn.

GARLIC, A SHIELDING PROGRAM FOR GAMMA RADIATION FROM LINE- AND CYLINDER- SOURCES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roos, M.

1959-06-01

GARLlC is a program for computing the gamma ray flux or dose rate at a shielded isotropic point detector, due to a line source or the line equivalent of a cylindrical source. The source strength distribution along the line must be either uniform or an arbitrary part of the positive half-cycle of a cosine function The line source can be orierted arbitrarily with respect to the main shield and the detector, except that the detector must not be located on the line source or on its extensionThe main source is a homogeneous plane slab in which scattered radiation is accountedmore » for by multiplying each point element of the line source by a point source buildup factor inside the integral over the point elements. Between the main shield and the line source additional shields can be introduced, which are either plane slabs, parallel to the main shield, or cylindrical rings, coaxial with the line source. Scattered radiation in the additional shields can only be accounted for by constant build-up factors outside the integral. GARLlC-xyz is an extended version particularly suited for the frequently met problem of shielding a room containing a large number of line sources in diHerent positions. The program computes the angles and linear dimensions of a problem for GARLIC when the positions of the detector point and the end points of the line source are given as points in an arbitrary rectangular coordinate system. As an example the isodose curves in water are presented for a monoenergetic cosine-distributed line source at several source energies and for an operating fuel element of the Swedish reactor R3, (auth)« less

[Accuracy of attenuation coefficient obtained by 137Cs single-transmission scanning in PET: comparison with conventional germanium line source].

PubMed

Matsumoto, Keiichi; Kitamura, Keishi; Mizuta, Tetsuro; Shimizu, Keiji; Murase, Kenya; Senda, Michio

2006-02-20

Transmission scanning can be successfully performed with a Cs-137 single-photon-emitting point source for three-dimensional PET imaging. This method was effective for postinjection transmission scanning because of differences in physical energy. However, scatter contamination in the transmission data lowers measured attenuation coefficients. The purpose of this study was to investigate the accuracy of the influence of object scattering by measuring the attenuation coefficients on the transmission images. We also compared the results with the conventional germanium line source method. Two different types of PET scanner, the SET-3000 G/X (Shimadzu Corp.) and ECAT EXACT HR(+) (Siemens/CTI) , were used. For the transmission scanning, the SET-3000 G/X and ECAT HR(+) were the Cs-137 point source and Ge-68/Ga-68 line source, respectively. With the SET-3000 G/X, we performed transmission measurement at two energy gate settings, the standard 600-800 keV as well as 500-800 keV. The energy gate setting of the ECAT HR(+) was 350-650 keV. The effects of scattering in a uniform phantom with different cross-sectional areas ranging from 201 cm(2) to 314 cm(2) to 628 cm(2) (apposition of the two 20 cm diameter phantoms) and 943 cm(2) (stacking of the three 20 cm diameter phantoms) were acquired without emission activity. First, we evaluated the attenuation coefficients of the two different types of transmission scanning using region of interest (ROI) analysis. In addition, we evaluated the attenuation coefficients with and without segmentation for Cs-137 transmission images using the same analysis. The segmentation method was a histogram-based soft-tissue segmentation process that can also be applied to reconstructed transmission images. In the Cs-137 experiment, the maximum underestimation was 3% without segmentation, which was reduced to less than 1% with segmentation at the center of the largest phantom. In the Ge-68/Ga-68 experiment, the difference in mean attenuation coefficients was stable with all phantoms. We evaluated the accuracy of attenuation coefficients of Cs-137 single-transmission scans. The results for Cs-137 suggest that scattered photons depend on object size. Although Cs-137 single-transmission scans contained scattered photons, attenuation coefficient error could be reduced using by the segmentation method.

Absolute Calibration of the AXAF Telescope Effective Area

NASA Technical Reports Server (NTRS)

Kellogg, E.; Cohen, L.; Edgar, R.; Evans, I.; Freeman, M.; Gaetz, T.; Jerius, D.; McDermott, W. C.; McKinnon, P.; Murray, S.;

Public transit to public lands : the nature express.

DOT National Transportation Integrated Search

2017-05-01

Access to leisure by public transportation has not been studied in great detail, at least in the United States. The Northeastern Illinois region with the City of Chicago (in Cook County) as the focal point is home to the third largest public transpor...

Managing Food Allergies at Home

MedlinePlus

... of reactions. Learn more here. Milk Egg Peanut Tree Nuts Soy Wheat Fish Shellfish Sesame Other Food Allergens Allergy Alerts Research Programs Research Programs We are the world’s largest private source of food allergy research funding. ...

THE COGNITIVE COMPETENCES OF IMMIGRANT AND NATIVE STUDENTS ACROSS THE WORLD: AN ANALYSIS OF GAPS, POSSIBLE CAUSES AND IMPACT.

PubMed

Rindermann, Heiner; Thompson, James

2016-01-01

Immigration, immigration policies and education of immigrants alter competence levels. This study analysed their effects using PISA, TIMSS and PIRLS data (1995 to 2012, N=93 nations) for natives' and immigrants' competences, competence gaps and their population proportions. The mean gap is equivalent to 4.71 IQ points. There are large differences across countries in these gaps ranging from around +12 to -10 IQ points. Migrants' proportions grow roughly 4% per decade. The largest immigrant-based 'brain gains' are observed for Arabian oil-based economies, and the largest 'brain losses' for Central Europe. Regarding causes of native-immigrant gaps, language problems do not seem to explain them. However, English-speaking countries show an advantage. Acculturation within one generation and intermarriage usually reduce native-immigrant gaps (≅1 IQ point). National educational quality reduces gaps, especially school enrolment at a young age, the use of tests and school autonomy. A one standard deviation increase in school quality represents a closing of around 1 IQ point in the native-immigrant gap. A new Greenwich IQ estimation based on UK natives' cognitive ability mean is recommended. An analysis of the first adult OECD study PIAAC revealed that larger proportions of immigrants among adults reduce average competence levels and positive Flynn effects. The effects on economic development and suggestions for immigration and educational policy are discussed.

Black:White disparities in lung cancer mortality in the 50 largest cities in the United States.

PubMed

Hunt, Bijou; Balachandran, Banujan

2015-12-01

This paper presents race-specific lung cancer mortality rates and the corresponding rate ratios for the 50 largest U.S. cities for the 5-year intervals 1990-1994 and 2005-2009. The 50 largest cities in the U.S. were the units of analysis. Numerator data were abstracted from national death files where the cause was malignant neoplasms of trachea, bronchus, and lung (lung cancer) (ICD-9=162 and ICD-10=C33-C34). Population-based denominators were obtained from the U.S. Census Bureau for 1990, 2000, and 2010. To measure the racial disparity, we calculated non-Hispanic Black:non-Hispanic White rate ratios (RRs) and confidence intervals for each 5-year period. We calculated correlation coefficients for 12 ecological variables and the RRs. At the final time point (2005-2009), 15RRs were less than 1, but only 8 significantly so while 29RRs were greater than 1, 16 of them significantly so. Of the 45 cities included in the analysis, 21 saw an increase in the Black:White RR between the first and second time points. Measures of socioeconomic status (SES) and inequalities therein were found to be associated with the RRs. This analysis revealed large disparities in Black:White lung cancer mortality in the U.S. and many of its largest cities during the period 1990-2009. The data demonstrate considerable variation in the degree of disparity across cities, even among cities within the same state. These data can inform and motivate local health officials to implement targeted prevention and treatment strategies where they are needed most, ultimately contributing to a reduction in the disparity in lung cancer mortality rates. Copyright © 2015 Elsevier Ltd. All rights reserved.

40 CFR 51.35 - How can my state equalize the emission inventory effort from year to year?

Code of Federal Regulations, 2012 CFR

2012-07-01

... approach: (1) Each year, collect and report data for all Type A (large) point sources (this is required for all Type A point sources). (2) Each year, collect data for one-third of your sources that are not Type... save 3 years of data and then report all emissions from the sources that are not Type A point sources...

40 CFR 51.35 - How can my state equalize the emission inventory effort from year to year?

Code of Federal Regulations, 2010 CFR

2010-07-01

... approach: (1) Each year, collect and report data for all Type A (large) point sources (this is required for all Type A point sources). (2) Each year, collect data for one-third of your sources that are not Type... save 3 years of data and then report all emissions from the sources that are not Type A point sources...

40 CFR 51.35 - How can my state equalize the emission inventory effort from year to year?

Code of Federal Regulations, 2014 CFR

2014-07-01

... approach: (1) Each year, collect and report data for all Type A (large) point sources (this is required for all Type A point sources). (2) Each year, collect data for one-third of your sources that are not Type... save 3 years of data and then report all emissions from the sources that are not Type A point sources...

X-ray bright points and He I lambda 10830 dark points

NASA Technical Reports Server (NTRS)

Golub, L.; Harvey, K. L.; Herant, M.; Webb, D. F.

1989-01-01

Using near-simultaneous full disk Solar X-ray images and He I 10830 lambda, spectroheliograms from three recent rocket flights, dark points identified on the He I maps were compared with X-ray bright points identified on the X-ray images. It was found that for the largest and most obvious features there is a strong correlation: most He I dark points correspond to X-ray bright points. However, about 2/3 of the X-ray bright points were not identified on the basis of the helium data alone. Once an X-ray feature is identified it is almost always possible to find an underlying dark patch of enhanced He I absorption which, however, would not a priori have been selected as a dark point. Therefore, the He I dark points, using current selection criteria, cannot be used as a one-to-one proxy for the X-ray data. He I dark points do, however, identify the locations of the stronger X-ray bright points.

X-ray bright points and He I lambda 10830 dark points

NASA Technical Reports Server (NTRS)

Golub, L.; Harvey, K. L.; Herant, M.; Webb, D. F.

1989-01-01

Using near-simultaneous full disk Solar X-ray images and He I 10830 lambda, spectroheliograms from three recent rocket flights, dark points identified on the He I maps were compared with x-ray bright points identified on the X-ray images. It was found that for the largest and most obvious features there is a strong correlation: most He I dark points correspond to X-ray bright points. However, about 2/3 of the X-ray bright points were not identified on the basis of the helium data alone. Once an X-ray feature is identified it is almost always possible to find an underlying dark patch of enhanced He I absorption which, however, would not a priori have been selected as a dark point. Therefore, the He I dark points, using current selection criteria, cannot be used as a one-to-one proxy for the X-ray data. He I dark points do, however, identify the locations of the stronger X-ray bright points.

Development and Evaluation of an Air Quality Modeling Approach to Assess Near-Field Impacts of Lead Emissions from Piston-Engine Aircraft Operating on Leaded Aviation Gasoline

EPA Science Inventory

Since aviation gasoline is now the largest remaining source of lead (Pb) emissions to the air in the United States, there is increased interest by regulatory agencies and the public in assessing the impacts on residents living in close proximity to these sources. An air quality m...

Lesson and Impressions of the Ghanaian Capital Markets

DTIC Science & Technology

2011-07-31

with natural resources, Ghana has roughly twice the per capita output of the poorest countries in West Africa. Gold and cocoa production are major...sources of foreign exchange. Interestingly, the country’s largest source of foreign exchange is remittances from workers abroad. Oil production has...prominent industries include textiles, apparel, steel, tires, flour milling, cocoa processing, beverages, tobacco, simple consumer goods, and car, truck

Puncturevine seed response to postemergence herbicides

USDA-ARS?s Scientific Manuscript database

Puncturevine (Tribulus terrestris) continues to plague growers, vegetation managers, and home gardeners. Puncturevine is a summer annual weed with spiny fruits that split into five segments, each containing one to four seeds. The seed nearest the pointed end of the bur is the largest and usually ge...

An Industry Redefined

ERIC Educational Resources Information Center

Breeding, Marshall

2007-01-01

Activities in 2006 pointed to strategic shifts in library automation. The dynamics of the business environment changed rapidly from a fragmented industry to a highly consolidated one. Though the integrated library system (ILS) continues to represent the largest portion of revenue, products that deal with electronic content and deliver better…

Benchmark Testing of the Largest Titanium Aluminide Sheet Subelement Conducted

NASA Technical Reports Server (NTRS)

Bartolotta, Paul A.; Krause, David L.

2000-01-01

To evaluate wrought titanium aluminide (gamma TiAl) as a viable candidate material for the High-Speed Civil Transport (HSCT) exhaust nozzle, an international team led by the NASA Glenn Research Center at Lewis Field successfully fabricated and tested the largest gamma TiAl sheet structure ever manufactured. The gamma TiAl sheet structure, a 56-percent subscale divergent flap subelement, was fabricated for benchmark testing in three-point bending. Overall, the subelement was 84-cm (33-in.) long by 13-cm (5-in.) wide by 8-cm (3-in.) deep. Incorporated into the subelement were features that might be used in the fabrication of a full-scale divergent flap. These features include the use of: (1) gamma TiAl shear clips to join together sections of corrugations, (2) multiple gamma TiAl face sheets, (3) double hot-formed gamma TiAl corrugations, and (4) brazed joints. The structural integrity of the gamma TiAl sheet subelement was evaluated by conducting a room-temperature three-point static bend test.

The Unified Lunar Control Network 2005

USGS Publications Warehouse

Archinal, Brent A.; Rosiek, Mark R.; Kirk, Randolph L.; Redding, Bonnie L.

2006-01-01

This report documents a new general unified lunar control network and lunar topographic model based on a combination of Clementine images and a previous network derived from Earth-based & Apollo photographs, and Mariner 10, & Galileo images. This photogrammetric network solution is the largest planetary control network ever completed. It includes the determination of the 3-D positions of 272,931 points on the lunar surface and the correction of the camera angles for 43,866 Clementine images, using 546,126 tie point measurements. The solution RMS is 20 ?m (= 0.9 pixels) in the image plane, with the largest residual of 6.4 pixels. The explanation given here, along with the accompanying files, comprises the release of the network information and of global lunar digital elevation models (DEMs) derived from the network. A paper that will describe the solution and network in further detail will be submitted to a refereed journal, and will include additional background information, solution details, discussion of accuracy and precision, and explanatory figures.

Non-domestic phosphorus release in rivers during low-flow: Mechanisms and implications for sources identification

NASA Astrophysics Data System (ADS)

Dupas, Rémi; Tittel, Jörg; Jordan, Phil; Musolff, Andreas; Rode, Michael

2018-05-01

A common assumption in phosphorus (P) load apportionment studies is that P loads in rivers consist of flow independent point source emissions (mainly from domestic and industrial origins) and flow dependent diffuse source emissions (mainly from agricultural origin). Hence, rivers dominated by point sources will exhibit highest P concentration during low-flow, when flow dilution capacity is minimal, whereas rivers dominated by diffuse sources will exhibit highest P concentration during high-flow, when land-to-river hydrological connectivity is maximal. Here, we show that Soluble Reactive P (SRP) concentrations in three forested catchments free of point sources exhibited seasonal maxima during the summer low-flow period, i.e. a pattern expected in point source dominated areas. A load apportionment model (LAM) is used to show how point sources contribution may have been overestimated in previous studies, because of a biogeochemical process mimicking a point source signal. Almost twenty-two years (March 1995-September 2016) of monthly monitoring data of SRP, dissolved iron (Fe) and nitrate-N (NO3) were used to investigate the underlying mechanisms: SRP and Fe exhibited similar seasonal patterns and opposite to that of NO3. We hypothesise that Fe oxyhydroxide reductive dissolution might be the cause of SRP release during the summer period, and that NO3 might act as a redox buffer, controlling the seasonality of SRP release. We conclude that LAMs may overestimate the contribution of P point sources, especially during the summer low-flow period, when eutrophication risk is maximal.

Calculation and analysis of the non-point source pollution in the upstream watershed of the Panjiakou Reservoir, People's Republic of China

NASA Astrophysics Data System (ADS)

Zhang, S.; Tang, L.

2007-05-01

Panjiakou Reservoir is an important drinking water resource in Haihe River Basin, Hebei Province, People's Republic of China. The upstream watershed area is about 35,000 square kilometers. Recently, the water pollution in the reservoir is becoming more serious owing to the non-point pollution as well as point source pollution on the upstream watershed. To effectively manage the reservoir and watershed and develop a plan to reduce pollutant loads, the loading of non-point and point pollution and their distribution on the upstream watershed must be understood fully. The SWAT model is used to simulate the production and transportation of the non-point source pollutants in the upstream watershed of the Panjiakou Reservoir. The loadings of non-point source pollutants are calculated for different hydrologic years and the spatial and temporal characteristics of non-point source pollution are studied. The stream network and topographic characteristics of the stream network and sub-basins are all derived from the DEM by ArcGIS software. The soil and land use data are reclassified and the soil physical properties database file is created for the model. The SWAT model was calibrated with observed data of several hydrologic monitoring stations in the study area. The results of the calibration show that the model performs fairly well. Then the calibrated model was used to calculate the loadings of non-point source pollutants for a wet year, a normal year and a dry year respectively. The time and space distribution of flow, sediment and non-point source pollution were analyzed depending on the simulated results. The comparison of different hydrologic years on calculation results is dramatic. The loading of non-point source pollution in the wet year is relatively larger but smaller in the dry year since the non-point source pollutants are mainly transported through the runoff. The pollution loading within a year is mainly produced in the flood season. Because SWAT is a distributed model, it is possible to view model output as it varies across the basin, so the critical areas and reaches can be found in the study area. According to the simulation results, it is found that different land uses can yield different results and fertilization in rainy season has an important impact on the non- point source pollution. The limitations of the SWAT model are also discussed and the measures of the control and prevention of non- point source pollution for Panjiakou Reservoir are presented according to the analysis of model calculation results.

Metal enrichment and lead isotope analysis for source apportionment in the urban dust and rural surface soil.

PubMed

Yu, Yang; Li, Yingxia; Li, Ben; Shen, Zhenyao; Stenstrom, Michael K

2016-09-01

To understand the metal accumulation in the environment and identify its sources, 29 different metal contents and lead (Pb) isotope ratios were determined for 40 urban dust samples, 36 surface soil samples, and one river sediment sample collected in the municipality of Beijing, China. Results showed that cadmium, copper (Cu), mercury, Pb, antimony (Sb), and zinc demonstrated to be the typical urban contaminants and mostly influenced by the adjacent human activities with higher content to background ratios and SD values. Among the 29 metal elements investigated, Cu and Sb were found to be the most distinct elements that were highly affected by the developing level and congestion status of the cities with much higher contents in dust in more developed and congested cities. There was a relatively wider range of Pb isotope ratios of country surface soil than those of urban dust. The results of source identification based on Pb isotope ratios showed that coal combustion was the first largest Pb source and vehicle exhaust was the second largest source. The sum of them accounted for 74.6% mass proportion of overall Pb pollution on average. The surface soil sample collected at an iron mine had the highest (204)Pb/(206)Pb, (207)Pb/(206)Pb, and (208)Pb/(206)Pb ratios indicating ore had much higher ratios than other sources. The fine particle subsamples had higher (204)Pb/(206)Pb, (207)Pb/(206)Pb, and (208)Pb/(206)Pb ratios than the coarse particle subsamples indicating more anthropogenic sources of coal combustion and vehicle exhaust for fine particles and more background influence for coarse particles. These results help with pinpointing the major Pb sources and applying suitable measures for the target sources. Copyright © 2016 Elsevier Ltd. All rights reserved.

Nation's Largest Biomass Conference To Draw International Experts

Science.gov Websites

assess the role of biomass as a leading energy source in the next century. Several conference sessions substantially boost the role of biomass and bioenergy in domestic energy supplies and rural development. The

A DATABASE FOR TRACKING TOXICOGENOMIC SAMPLES AND PROCEDURES

EPA Science Inventory

Reproductive toxicogenomic studies generate large amounts of toxicological and genomic data. On the toxicology side, a substantial quantity of data accumulates from conventional endpoints such as histology, reproductive physiology and biochemistry. The largest source of genomics...

Black Carbon Diesel Initiative in the Russian Arctic

EPA Pesticide Factsheets

Mobile and stationary diesel engines are among the largest sources of black carbon emissions in the Arctic. To address this challenge, EPA is leading the Black Carbon Diesel Initiative under the Arctic Black Carbon Initiative (ABCI).

Active control on high-order coherence and statistic characterization on random phase fluctuation of two classical point sources.

PubMed

Hong, Peilong; Li, Liming; Liu, Jianji; Zhang, Guoquan

2016-03-29

Young's double-slit or two-beam interference is of fundamental importance to understand various interference effects, in which the stationary phase difference between two beams plays the key role in the first-order coherence. Different from the case of first-order coherence, in the high-order optical coherence the statistic behavior of the optical phase will play the key role. In this article, by employing a fundamental interfering configuration with two classical point sources, we showed that the high- order optical coherence between two classical point sources can be actively designed by controlling the statistic behavior of the relative phase difference between two point sources. Synchronous position Nth-order subwavelength interference with an effective wavelength of λ/M was demonstrated, in which λ is the wavelength of point sources and M is an integer not larger than N. Interestingly, we found that the synchronous position Nth-order interference fringe fingerprints the statistic trace of random phase fluctuation of two classical point sources, therefore, it provides an effective way to characterize the statistic properties of phase fluctuation for incoherent light sources.

Source and fate of inorganic solutes in the Gibbon River, Yellowstone National Park, Wyoming, USA: I. Low-flow discharge and major solute chemistry

USGS Publications Warehouse

McCleskey, R. Blaine; Nordstrom, D. Kirk; Susong, David D.; Ball, James W.; Holloway, JoAnn M.

2010-01-01

The Gibbon River in Yellowstone National Park (YNP) is an important natural resource and habitat for fisheries and wildlife. However, the Gibbon River differs from most other mountain rivers because its chemistry is affected by several geothermal sources including Norris Geyser Basin, Chocolate Pots, Gibbon Geyser Basin, Beryl Spring, and Terrace Spring. Norris Geyser Basin is one of the most dynamic geothermal areas in YNP, and the water discharging from Norris is much more acidic (pH 3) than other geothermal basins in the upper-Madison drainage (Gibbon and Firehole Rivers). Water samples and discharge data were obtained from the Gibbon River and its major tributaries near Norris Geyser Basin under the low-flow conditions of September 2006. Surface inflows from Norris Geyser Basin were sampled to identify point sources and to quantify solute loading to the Gibbon River. The source and fate of the major solutes (Ca, Mg, Na, K, SiO2, Cl, F, HCO3, SO4, NO3, and NH4) in the Gibbon River were determined in this study and these results may provide an important link in understanding the health of the ecosystem and the behavior of many trace solutes. Norris Geyser Basin is the primary source of Na, K, Cl, SO4, and N loads (35–58%) in the Gibbon River. The largest source of HCO3 and F is in the lower Gibbon River reach. Most of the Ca and Mg originate in the Gibbon River upstream from Norris Geyser Basin. All the major solutes behave conservatively except for NH4, which decreased substantially downstream from Gibbon Geyser Basin, and SiO2, small amounts of which precipitated on mixing of thermal drainage with the river. As much as 9–14% of the river discharge at the gage is from thermal flows during this period.

Trends and sources vs air mass origins in a major city in South-western Europe: Implications for air quality management.

PubMed

Fernández-Camacho, R; de la Rosa, J D; Sánchez de la Campa, A M

2016-05-15

This study presents a 17-years air quality database comprised of different parameters corresponding to the largest city in the south of Spain (Seville) where atmospheric pollution is frequently attributed to traffic emissions and is directly affected by Saharan dust outbreaks. We identify the PM10 contributions from both natural and anthropogenic sources in this area associated to different air mass origins. Hourly, daily and seasonal variation of PM10 and gaseous pollutant concentrations (CO, NO2 and SO2), all of them showing negative trends during the study period, point to the traffic as one of the main sources of air pollution in Seville. Mineral dust, secondary inorganic compounds (SIC) and trace elements showed higher concentrations under North African (NAF) air mass origins than under Atlantic. We observe a decreasing trend in all chemical components of PM10 under both types of air masses, NAF and Atlantic. Principal component analysis using more frequent air masses in the area allows the identification of five PM10 sources: crustal, regional, marine, traffic and industrial. Natural sources play a more relevant role during NAF events (20.6 μg · m(-3)) than in Atlantic episodes (13.8 μg · m(-3)). The contribution of the anthropogenic sources under NAF doubles the one under Atlantic conditions (33.6 μg · m(-3) and 15.8 μg · m(-3), respectively). During Saharan dust outbreaks the frequent accumulation of local anthropogenic pollutants in the lower atmosphere results in poor air quality and an increased risk of mortality. The results are relevant when analysing the impact of anthropogenic emissions on the exposed population in large cities. The increase in potentially toxic elements during Saharan dust outbreaks should also be taken into account when discounting the number of exceedances attributable to non-anthropogenic or natural origins. Copyright © 2016 Elsevier B.V. All rights reserved.

GBIS: the information system of the German Genebank

PubMed Central

Oppermann, Markus; Weise, Stephan; Dittmann, Claudia; Knüpffer, Helmut

2015-01-01

The German Federal ex situ Genebank of Agricultural and Horticultural Crop Species is the largest collection of its kind in the countries of the European Union and amongst the 10 largest collections worldwide. Beside its enormous scientific value as a safeguard of plant biodiversity, the plant genetic resources maintained are also of high importance for breeders to provide new impulses. The complex processes of managing such a collection are supported by the Genebank Information System (GBIS). GBIS is an important source of information for researchers and plant breeders, e.g. for identifying appropriate germplasm for breeding purposes. In addition, the access to genebank material as a sovereign task is also of high interest to the general public. Moreover, GBIS acts as a data source for global information systems, such as the Global Biodiversity Information Facility (GBIF) or the European Search Catalogue for Plant Genetic Resources (EURISCO). Database URL: http://gbis.ipk-gatersleben.de/ PMID:25953079

Study on Sources of Volatile Organic Compounds (CMB) in Pearl River Delta region, China

NASA Astrophysics Data System (ADS)

Liu, Y.; Shao, M.; Lu, S.; Chang, C.; Wang, C. J.; Wang, B.

2007-05-01

The profiles of major Volatile organic compounds (VOCs) sources including vehicle exhaust, gasoline vapor, painting, asphalt, liquefied petroleum gas (LPG), biomass burning and petrochemical industry in Pearl River Delta were experimentally determined. Source samples were taken by using dilution chamber for mobile and stationary sources, laboratory simulation for biomass burning. The concentrations of 108 VOC species of sources were quantified by using canister with pre-concentration-GC/MS system, from which 52 PAMS hydrocarbons and one kind of chlorinated hydrocarbon were deployed to build the source profiles for source apportionment of VOCs. Based the measurement of source profiles, the possible tracers for various emission sources were identified, e.g 2-methylbutane and 1,3-butadiene were the tracers for motor vehicle exhaust, the characteristic compounds of architectural and furnishing coatings are aromatics such as toluene and m/p-xylene; the light hydrocarbons, namely n-butane, trans-2-butene and n-pentane, dominated the composition of gasoline vapor; and the nonane, decane and undecane are found to represent the asphalt emissions etc.. The CMB receptor model was applied to source apportionment of 58 hydrocarbons measured at seven sites during the PRD campaign, 2004. The 12 kinds of VOC sources include gasoline/diesel-powered vehicle exhaust, gasoline/diesel headspace vapor, vehicle evaporative emissions, liquid petroleum gas (LPG) leakage, painting vapors, asphalt emission from paved road, biomass burning, coal burning, chemical industry and petroleum refinery. Vehicle exhaust was the largest sources contributing over half of the ambient VOCs at the three urban sites (GuangZhou, FoShan and ZhongShan). LPG leakage played an important role with the percentage of 8- 16% in most sites in PRD. Contributions from solvents usage were highest at DongGuan, an industrial site. At XinKen, the solvents and coatings had the largest percentage of 31% probably due to the influence of its upwind area of DongGuan. The local biomass burning was also found to be a noticeable source at XK.

Spatial patterns of a tropical tree species growing under an eucalyptus plantation in South-East Brazil.

PubMed

Higuchi, P; Silva, A C; Louzada, J N C; Machado, E L M

2010-05-01

The objectives of this study were to evaluate the influence of propagules source and the implication of tree size class on the spatial pattern of Xylopia brasiliensis Spreng. individuals growing under the canopy of an experimental plantation of eucalyptus. To this end, all individuals of Xylopia brasiliensis with diameter at soil height (dsh) > 1 cm were mapped in the understory of a 3.16 ha Eucalyptus spp. and Corymbia spp. plantation, located in the municipality of Lavras, SE Brazil. The largest nearby mature tree of X. brasiliensis was considered as the propagules source. Linear regressions were used to assess the influence of the distance of propagules source on the population parameters (density, basal area and height). The spatial pattern of trees was assessed through the Ripley K function. The overall pattern showed that the propagules source distance had strong influence over spatial distribution of trees, mainly the small ones, indicating that the closer the distance from the propagules source, the higher the tree density and the lower the mean tree height. The population showed different spatial distribution patterns according to the spatial scale and diameter class considered. While small trees tended to be aggregated up to around 80 m, the largest individuals were randomly distributed in the area. A plausible explanation for observed patterns might be limited seed rain and intra-population competition.

Energy intake and sources of energy intake in the European Prospective Investigation into Cancer and Nutrition.

PubMed

Ocké, M C; Larrañaga, N; Grioni, S; van den Berg, S W; Ferrari, P; Salvini, S; Benetou, V; Linseisen, J; Wirfält, E; Rinaldi, S; Jenab, M; Halkjaer, J; Jakobsen, M U; Niravong, M; Clavel-Chapelon, F; Kaaks, R; Bergmann, M; Moutsiou, E; Trichopoulou, A; Lauria, C; Sacerdote, C; Bueno-de-Mesquita, H B; Peeters, P H M; Hjartåker, A; Parr, C L; Tormo, M J; Sanchez, M J; Manjer, J; Hellstrom, V; Mulligan, A; Spencer, E A; Riboli, E; Bingham, S; Slimani, N

2009-11-01

To describe energy intake and its macronutrient and food sources among 27 regions in 10 countries participating in the European Prospective Investigation into Cancer and Nutrition (EPIC) study. Between 1995 and 2000, 36 034 subjects aged 35-74 years were administered a standardized 24-h dietary recall. Intakes of macronutrients (g/day) and energy (kcal/day) were estimated using standardized national nutrient databases. Mean intakes were weighted by season and day of the week and were adjusted for age, height and weight, after stratification by gender. Extreme low- and high-energy reporters were identified using Goldberg's cutoff points (ratio of energy intake and estimated basal metabolic rate <0.88 or >2.72), and their effects on macronutrient and energy intakes were studied. Low-energy reporting was more prevalent in women than in men. The exclusion of extreme-energy reporters substantially lowered the EPIC-wide range in mean energy intake from 2196-2877 to 2309-2866 kcal among men. For women, these ranges were 1659-2070 and 1873-2108 kcal. There was no north-south gradient in energy intake or in the prevalence of low-energy reporting. In most centres, cereals and cereal products were the largest contributors to energy intake. The food groups meat, dairy products and fats and oils were also important energy sources. In many centres, the highest mean energy intakes were observed on Saturdays. These data highlight and quantify the variations and similarities in energy intake and sources of energy intake among 10 European countries. The prevalence of low-energy reporting indicates that the study of energy intake is hampered by the problem of underreporting.

Hydraulic Fracturing Induced Seismicity at Preese Hall, UK: Moment Tensors, Uncertainties and Implications for Microseismic Monitoring Strategies

NASA Astrophysics Data System (ADS)

O'toole, T. B.; Woodhouse, J. H.; Verdon, J.; Kendall, J.

2012-12-01

Hydraulic fracturing operations carried out in April and May 2011 by Cuadrilla Resources Ltd. during the exploration of a shale gas reservoir at Preese Hall, near Blackpool, UK, induced a series of microseismic events. The largest of these, with magnitude ML = 2.3, was felt at the surface and recorded by the British Geological Survey regional seismic network. Subsequently, two local seismic stations were installed, which continued to detect seismicity with ML ≤ 1.5 until the hydraulic fracture treatment was suspended due to the anomalously large magnitudes of the induced earthquakes. Here, we present the results of moment tensor inversions of seismic waveforms recorded by these two near-field stations. We determine the best point source description of an event by minimising the least-squares difference between observed and synthetic waveforms. In contrast to source mechanisms obtained from body wave polarity and amplitude picks, which require a good sampling of the focal sphere and typically assume a pure double-couple mechanism, using the whole waveform allows us to place good constraints on the moment tensor even when only a few seismograms are available, and also enables the investigation of possible non-double-couple components and volume changes associated with a source. We discuss our results in the context of the studies commissioned by Cuadrilla after the suspension of hydraulic fracturing operations at Preese Hall. Using synthetic waveform data, we investigate how different monitoring geometries can be used to reduce uncertainties in source parameters of induced microseisms. While our focus is on the monitoring of hydraulic fracturing operations, the methods developed here are general and could equally be applied to determine moment tensors from surface and borehole observations of seismicity induced by other activities.

A Collaborative Study of Source Apportionment and Total City Emissions of CH4 from Indianapolis

NASA Astrophysics Data System (ADS)

Hajny, K. D.; Davis, K. J.; Franklin, J. E.; Harvey, R. M.; Lavoie, T. N.; Miles, N. L.; Richardson, S.; Salmon, O. E.; Sarmiento, D. P.; Shepson, P. B.; Stirm, B. H.; Wofsy, S.

2016-12-01

Methane (CH4) is the second most important greenhouse gas emitted in the United States, accounting for about 11% of all US greenhouse gas emissions in 2014. Over 60% of CH4 emissions globally are due to human activity and two of the largest anthropogenic sources of CH4 are waste decomposition in landfills and losses from the energy sector. Indianapolis has been a testbed site for development of methods for quantitative urban-scale greenhouse gas emissions measurements, through the Indianapolis Flux Experiment (INFLUX) since 2010. Multiple airborne mass balance experiments with Purdue University's Airborne Laboratory for Atmospheric Research (ALAR) have been performed in the area to quantify greenhouse gas emissions, since 2008. Previous research has shown that the large landfill in Indianapolis is the only significant point source, emitting 45 ± 14 mols CH4/s or roughly 1/3 of all CH4 emissions. Propane/methane ratios have indicated that all other CH4 emissions were due to leaks in the natural gas distribution system in the city, but not all the sources have been identified. A recent collaborative effort aimed to investigate this further using tower based inversions from INFLUX data, ground based Lagrangian transport modeling using Fourier Transform Spectrometers, and airborne based mass balance experiments using ALAR. Within the 2-week long project there were 4 days with atmospheric conditions that allowed for simultaneous airborne and ground based measurements. Here we will discuss selected outcomes from this effort, including city-wide mass balance measurements from ALAR, our results in light of the FTS observations, and how the results compare to the historical data base for Indianapolis.

Patterns of mercury dispersion from local and regional emission sources, rural Central Wisconsin, USA

USGS Publications Warehouse

Kolker, A.; Olson, M.L.; Krabbenhoft, D.P.; Tate, M.T.; Engle, M.A.

2010-01-01

Simultaneous real-time changes in mercury (Hg) speciation ?????" reactive gaseous Hg (RGM), elemental Hg (Hg??), and fine particulate Hg (Hg-PM2.5), were determined from June to November 2007, in ambient air at three locations in rural Central Wisconsin. Known Hg emission sources within the airshed of the monitoring sites include: 1) a 1114 megawatt (MW) coal-fired electric utility generating station; 2) a Hg-bed chlor-alkali plant; and 3) a smaller (465 MW) coal-burning electric utility. Monitoring sites, showing sporadic elevation of RGM, Hg?? and Hg-PM 2.5, were positioned at distances of 25, 50 and 100 km northward of the larger electric utility. A series of RGM events were recorded at each site. The largest, on 23 September, occurred under prevailing southerly winds, with a maximum RGM value (56.8 pg m-3) measured at the 100 km site, and corresponding elevated SO2 (10.41 ppbv; measured at 50 km site). The finding that RGM, Hg??, and Hg-PM2.5 are not always highest at the 25 km site, closest to the large generating station, contradicts the idea that RGM decreases with distance from a large point source. This may be explained if: 1) the 100 km site was influenced by emissions from the chlor-alkali facility or by RGM from regional urban sources; 2) the emission stack height of the larger power plant promoted plume transport at an elevation where the Hg is carried over the closest site; or 3) RGM was being generated in the plume through oxidation of Hg??. Operational changes at each emitter since 2007 should reduce their Hg output, potentially allowing quantification of the environmental benefit in future studies.

Indigenous obesity in the news: a media analysis of news representation of obesity in Australia's Indigenous population.

PubMed

Islam, Salwa; Fitzgerald, Lisa

2016-01-01

High rates of obesity are a significant issue amongst Indigenous populations in many countries around the world. Media framing of issues can play a critical role in shaping public opinion and government policy. A broad range of media analyses have been conducted on various aspects of obesity, however media representation of Indigenous obesity remains unexplored. In this study we investigate how obesity in Australia's Indigenous population is represented in newsprint media coverage. Media articles published between 2007 and 2014 were analysed for the distribution and extent of coverage over time and across Indigenous and mainstream media sources using quantitative content analysis. Representation of the causes and solutions of Indigenous obesity and framing in text and image content was examined using qualitative framing analysis. Media coverage of Indigenous obesity was very limited with no clear trends in reporting over time or across sources. The single Indigenous media source was the second largest contributor to the media discourse of this issue. Structural causes/origins were most often cited and individual solutions were comparatively overrepresented. A range of frames were employed across the media sources. All images reinforced textual framing except for one article where the image depicted individual factors whereas the text referred to structural determinants. This study provides a starting point for an important area of research that needs further investigation. The findings highlight the importance of alternative news media outlets, such as The Koori Mail, and that these should be developed to enhance the quality and diversity of media coverage. Media organisations can actively contribute to improving Indigenous health through raising awareness, evidence-based balanced reporting, and development of closer ties with Indigenous health workers.

Tracking the deployment of the integrated metropolitan ITS infrastructure in Greensboro, Winston-Salem, High Point : FY99 results

DOT National Transportation Integrated Search

2000-01-01

In January 1996, Secretary Pea set a goal of deploying the integrated metropolitan Intelligent Transportation System (ITS) infrastructure in 75 of the nations largest metropolitan areas by 2006. In 1997, the U.S. Department of Transportation ini...

SPARROW models used to understand nutrient sources in the Mississippi/Atchafalaya River Basin

USGS Publications Warehouse

Robertson, Dale M.; Saad, David A.

2013-01-01

Nitrogen (N) and phosphorus (P) loading from the Mississippi/Atchafalaya River Basin (MARB) has been linked to hypoxia in the Gulf of Mexico. To describe where and from what sources those loads originate, SPAtially Referenced Regression On Watershed attributes (SPARROW) models were constructed for the MARB using geospatial datasets for 2002, including inputs from wastewater treatment plants (WWTPs), and calibration sites throughout the MARB. Previous studies found that highest N and P yields were from the north-central part of the MARB (Corn Belt). Based on the MARB SPARROW models, highest N yields were still from the Corn Belt but centered over Iowa and Indiana, and highest P yields were widely distributed throughout the center of the MARB. Similar to that found in other studies, agricultural inputs were found to be the largest N and P sources throughout most of the MARB: farm fertilizers were the largest N source, whereas farm fertilizers, manure, and urban inputs were dominant P sources. The MARB models enable individual N and P sources to be defined at scales ranging from SPARROW catchments (∼50 km2) to the entire area of the MARB. Inputs of P from WWTPs and urban areas were more important than found in most other studies. Information from this study will help to reduce nutrient loading from the MARB by providing managers with a description of where each of the sources of N and P are most important, thus providing a basis for prioritizing management actions and ultimately reducing the extent of Gulf hypoxia.

Quantitative modeling of the accuracy in registering preoperative patient-specific anatomic models into left atrial cardiac ablation procedures

PubMed Central

Rettmann, Maryam E.; Holmes, David R.; Kwartowitz, David M.; Gunawan, Mia; Johnson, Susan B.; Camp, Jon J.; Cameron, Bruce M.; Dalegrave, Charles; Kolasa, Mark W.; Packer, Douglas L.; Robb, Richard A.

2014-01-01

Purpose: In cardiac ablation therapy, accurate anatomic guidance is necessary to create effective tissue lesions for elimination of left atrial fibrillation. While fluoroscopy, ultrasound, and electroanatomic maps are important guidance tools, they lack information regarding detailed patient anatomy which can be obtained from high resolution imaging techniques. For this reason, there has been significant effort in incorporating detailed, patient-specific models generated from preoperative imaging datasets into the procedure. Both clinical and animal studies have investigated registration and targeting accuracy when using preoperative models; however, the effect of various error sources on registration accuracy has not been quantitatively evaluated. Methods: Data from phantom, canine, and patient studies are used to model and evaluate registration accuracy. In the phantom studies, data are collected using a magnetically tracked catheter on a static phantom model. Monte Carlo simulation studies were run to evaluate both baseline errors as well as the effect of different sources of error that would be present in a dynamic in vivo setting. Error is simulated by varying the variance parameters on the landmark fiducial, physical target, and surface point locations in the phantom simulation studies. In vivo validation studies were undertaken in six canines in which metal clips were placed in the left atrium to serve as ground truth points. A small clinical evaluation was completed in three patients. Landmark-based and combined landmark and surface-based registration algorithms were evaluated in all studies. In the phantom and canine studies, both target registration error and point-to-surface error are used to assess accuracy. In the patient studies, no ground truth is available and registration accuracy is quantified using point-to-surface error only. Results: The phantom simulation studies demonstrated that combined landmark and surface-based registration improved landmark-only registration provided the noise in the surface points is not excessively high. Increased variability on the landmark fiducials resulted in increased registration errors; however, refinement of the initial landmark registration by the surface-based algorithm can compensate for small initial misalignments. The surface-based registration algorithm is quite robust to noise on the surface points and continues to improve landmark registration even at high levels of noise on the surface points. Both the canine and patient studies also demonstrate that combined landmark and surface registration has lower errors than landmark registration alone. Conclusions: In this work, we describe a model for evaluating the impact of noise variability on the input parameters of a registration algorithm in the context of cardiac ablation therapy. The model can be used to predict both registration error as well as assess which inputs have the largest effect on registration accuracy. PMID:24506630

Quantitative modeling of the accuracy in registering preoperative patient-specific anatomic models into left atrial cardiac ablation procedures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rettmann, Maryam E., E-mail: rettmann.maryam@mayo.edu; Holmes, David R.; Camp, Jon J.

2014-02-15

Purpose: In cardiac ablation therapy, accurate anatomic guidance is necessary to create effective tissue lesions for elimination of left atrial fibrillation. While fluoroscopy, ultrasound, and electroanatomic maps are important guidance tools, they lack information regarding detailed patient anatomy which can be obtained from high resolution imaging techniques. For this reason, there has been significant effort in incorporating detailed, patient-specific models generated from preoperative imaging datasets into the procedure. Both clinical and animal studies have investigated registration and targeting accuracy when using preoperative models; however, the effect of various error sources on registration accuracy has not been quantitatively evaluated. Methods: Datamore » from phantom, canine, and patient studies are used to model and evaluate registration accuracy. In the phantom studies, data are collected using a magnetically tracked catheter on a static phantom model. Monte Carlo simulation studies were run to evaluate both baseline errors as well as the effect of different sources of error that would be present in a dynamicin vivo setting. Error is simulated by varying the variance parameters on the landmark fiducial, physical target, and surface point locations in the phantom simulation studies. In vivo validation studies were undertaken in six canines in which metal clips were placed in the left atrium to serve as ground truth points. A small clinical evaluation was completed in three patients. Landmark-based and combined landmark and surface-based registration algorithms were evaluated in all studies. In the phantom and canine studies, both target registration error and point-to-surface error are used to assess accuracy. In the patient studies, no ground truth is available and registration accuracy is quantified using point-to-surface error only. Results: The phantom simulation studies demonstrated that combined landmark and surface-based registration improved landmark-only registration provided the noise in the surface points is not excessively high. Increased variability on the landmark fiducials resulted in increased registration errors; however, refinement of the initial landmark registration by the surface-based algorithm can compensate for small initial misalignments. The surface-based registration algorithm is quite robust to noise on the surface points and continues to improve landmark registration even at high levels of noise on the surface points. Both the canine and patient studies also demonstrate that combined landmark and surface registration has lower errors than landmark registration alone. Conclusions: In this work, we describe a model for evaluating the impact of noise variability on the input parameters of a registration algorithm in the context of cardiac ablation therapy. The model can be used to predict both registration error as well as assess which inputs have the largest effect on registration accuracy.« less

The Australian methane budget: Interpreting surface and train-borne measurements using a chemistry transport model

NASA Astrophysics Data System (ADS)

Fraser, Annemarie; Chan Miller, Christopher; Palmer, Paul I.; Deutscher, Nicholas M.; Jones, Nicholas B.; Griffith, David W. T.

2011-10-01

We investigate the Australian methane budget from 2005-2008 using the GEOS-Chem 3D chemistry transport model, focusing on the relative contribution of emissions from different sectors and the influence of long-range transport. To evaluate the model, we use in situ surface measurements of methane, methane dry air column average (XCH4) from ground-based Fourier transform spectrometers (FTSs), and train-borne surface concentration measurements from an in situ FTS along the north-south continental transect. We use gravity anomaly data from Gravity Recovery and Climate Experiment to describe the spatial and temporal distribution of wetland emissions and scale it to a prior emission estimate, which better describes observed atmospheric methane variability at tropical latitudes. The clean air sites of Cape Ferguson and Cape Grim are the least affected by local emissions, while Wollongong, located in the populated southeast with regional coal mining, samples the most locally polluted air masses (2.5% of the total air mass versus <1% at other sites). Averaged annually, the largest single source above background of methane at Darwin is long-range transport, mainly from Southeast Asia, accounting for ˜25% of the change in surface concentration above background. At Cape Ferguson and Cape Grim, emissions from ruminant animals are the largest source of methane above background, at approximately 20% and 30%, respectively, of the surface concentration. At Wollongong, emissions from coal mining are the largest source above background representing 60% of the surface concentration. The train data provide an effective way of observing transitions between urban, desert, and tropical landscapes.

The effect of emission from coal combustion in nonindustrial sources on deposition of sulfur and oxidized nitrogen in Poland.

PubMed

Kryza, Maciej; Werner, Małgorzata; Błaś, Marek; Dore, Anthony J; Sobik, Mieczysław

2010-07-01

Poland has one of the largest sulfur and nitrogen emissions in Europe. This is mainly because coal is a main fuel in industrial and nonindustrial combustion. The aim of this paper is to assess the amount of sulfur and nitrogen deposited from SNAP sector 02 (nonindustrial sources) coal combustion. To assess this issue, the Fine Resolution Atmospheric Multipollutant Exchange (FRAME) model was used. The results suggest that industrial combustion has the largest impact on deposition of oxidized sulfur, whereas the oxidized nitrogen national deposition budget is dominated by transboundary transport. The total mass of pollutants deposited in Poland, originating from nonindustrial coal combustion, is 45 Gg of sulfur and 2.5 Gg of nitrogen, which is over 18% of oxidized sulfur and nearly 2% of oxidized nitrogen deposited. SNAP 02 is responsible for up to 80% of dry-deposited sulfur and 11% of nitrogen. The contribution to wet deposition is largest in central Poland in the case of sulfur and in some areas can exceed 11%. For oxidized nitrogen, nonindustrial emissions contribute less than 1% over the whole area of Poland. The switch from coal to gas fuel in this sector will result in benefits in sulfur and nitrogen deposition reduction.

Spatial distribution and output characteristics of nonpoint source pollution in the Dongjiang River basin in south China

NASA Astrophysics Data System (ADS)

Rong, Q. Q.; Su, M. R.; Yang, Z. F.; Cai, Y. P.; Yue, W. C.; Dang, Z.

2018-02-01

In this research, the Dongjiang River basin was taken as the study area to analyze the spatial distribution and output characteristics of nonpoint source pollution, based on the export coefficient model. The results showed that the annual total nitrogen and phosphorus (i.e. TN and TP) loads from the Dongjiang River basin were 67916114.6 and 7215279.707 kg, respectively. Residents, forestland and pig were the main contributors for the TN load in the Dongjiang River basin, while residents, forestland and rainfed croplands were the three largest contributors for the TP load. The NPS pollution had a significant spatial variation in this area. The pollution loads overall decreased from the northeast to the southwest part of the basin. Also, the pollution loads from the gentle slope area were larger than those from steep slope areas. Among the ten tributary watersheds in the Dongjiang River basin, the TN and TP loads from the Hanxi River watershed were the largest. On the contrary, the Gongzhuang River watershed contributed least to the total pollution loads of the Dongjiang River basin. For the average pollution load intensities, Hanxi River watershed was still the largest. However, the smallest average TN and TP load intensities were in the Xinfeng River watershed.

Ghost imaging with bucket detection and point detection

NASA Astrophysics Data System (ADS)

Zhang, De-Jian; Yin, Rao; Wang, Tong-Biao; Liao, Qing-Hua; Li, Hong-Guo; Liao, Qinghong; Liu, Jiang-Tao

2018-04-01

We experimentally investigate ghost imaging with bucket detection and point detection in which three types of illuminating sources are applied: (a) pseudo-thermal light source; (b) amplitude modulated true thermal light source; (c) amplitude modulated laser source. Experimental results show that the quality of ghost images reconstructed with true thermal light or laser beam is insensitive to the usage of bucket or point detector, however, the quality of ghost images reconstructed with pseudo-thermal light in bucket detector case is better than that in point detector case. Our theoretical analysis shows that the reason for this is due to the first order transverse coherence of the illuminating source.

Distinguishing dark matter from unresolved point sources in the Inner Galaxy with photon statistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Samuel K.; Lisanti, Mariangela; Safdi, Benjamin R., E-mail: samuelkl@princeton.edu, E-mail: mlisanti@princeton.edu, E-mail: bsafdi@princeton.edu

2015-05-01

Data from the Fermi Large Area Telescope suggests that there is an extended excess of GeV gamma-ray photons in the Inner Galaxy. Identifying potential astrophysical sources that contribute to this excess is an important step in verifying whether the signal originates from annihilating dark matter. In this paper, we focus on the potential contribution of unresolved point sources, such as millisecond pulsars (MSPs). We propose that the statistics of the photons—in particular, the flux probability density function (PDF) of the photon counts below the point-source detection threshold—can potentially distinguish between the dark-matter and point-source interpretations. We calculate the flux PDFmore » via the method of generating functions for these two models of the excess. Working in the framework of Bayesian model comparison, we then demonstrate that the flux PDF can potentially provide evidence for an unresolved MSP-like point-source population.« less

Strong ground motion simulation of the 2016 Kumamoto earthquake of April 16 using multiple point sources

NASA Astrophysics Data System (ADS)

Nagasaka, Yosuke; Nozu, Atsushi

2017-02-01

The pseudo point-source model approximates the rupture process on faults with multiple point sources for simulating strong ground motions. A simulation with this point-source model is conducted by combining a simple source spectrum following the omega-square model with a path spectrum, an empirical site amplification factor, and phase characteristics. Realistic waveforms can be synthesized using the empirical site amplification factor and phase models even though the source model is simple. The Kumamoto earthquake occurred on April 16, 2016, with M JMA 7.3. Many strong motions were recorded at stations around the source region. Some records were considered to be affected by the rupture directivity effect. This earthquake was suitable for investigating the applicability of the pseudo point-source model, the current version of which does not consider the rupture directivity effect. Three subevents (point sources) were located on the fault plane, and the parameters of the simulation were determined. The simulated results were compared with the observed records at K-NET and KiK-net stations. It was found that the synthetic Fourier spectra and velocity waveforms generally explained the characteristics of the observed records, except for underestimation in the low frequency range. Troughs in the observed Fourier spectra were also well reproduced by placing multiple subevents near the hypocenter. The underestimation is presumably due to the following two reasons. The first is that the pseudo point-source model targets subevents that generate strong ground motions and does not consider the shallow large slip. The second reason is that the current version of the pseudo point-source model does not consider the rupture directivity effect. Consequently, strong pulses were not reproduced enough at stations northeast of Subevent 3 such as KMM004, where the effect of rupture directivity was significant, while the amplitude was well reproduced at most of the other stations. This result indicates the necessity for improving the pseudo point-source model, by introducing azimuth-dependent corner frequency for example, so that it can incorporate the effect of rupture directivity.[Figure not available: see fulltext.

STATISTICS OF GAMMA-RAY POINT SOURCES BELOW THE FERMI DETECTION LIMIT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malyshev, Dmitry; Hogg, David W., E-mail: dm137@nyu.edu

2011-09-10

An analytic relation between the statistics of photons in pixels and the number counts of multi-photon point sources is used to constrain the distribution of gamma-ray point sources below the Fermi detection limit at energies above 1 GeV and at latitudes below and above 30 deg. The derived source-count distribution is consistent with the distribution found by the Fermi Collaboration based on the first Fermi point-source catalog. In particular, we find that the contribution of resolved and unresolved active galactic nuclei (AGNs) to the total gamma-ray flux is below 20%-25%. In the best-fit model, the AGN-like point-source fraction is 17%more » {+-} 2%. Using the fact that the Galactic emission varies across the sky while the extragalactic diffuse emission is isotropic, we put a lower limit of 51% on Galactic diffuse emission and an upper limit of 32% on the contribution from extragalactic weak sources, such as star-forming galaxies. Possible systematic uncertainties are discussed.« less

Keeping the Future Bright: Department of Defense (DOD) Sustainable Energy Strategy for Installations

DTIC Science & Technology

2016-04-04

sustainable energy included renewable energy sources, such as hydroelectricity, solar energy, wind energy, wave power, geothermal energy, bioenergy, tidal...energy, including bioftiel and other alternative sources (wind. solar, and geothermal ).27 The SECNAV made security and independence the two energy...Navy’s China Lake geothermal power plant in California is DOD’s largest renewable energy project supplying nearly half of DOD’s renewable energy

Using Model Comparisons to Understand Sources of Nitrogen Delivered to US Coastal Areas

NASA Astrophysics Data System (ADS)

McCrackin, M. L.; Harrison, J.; Compton, J. E.

2011-12-01

Nitrogen loading to water bodies can result in eutrophication-related hypoxia and degraded water quality. The relative contributions of different anthropogenic and natural sources of in-stream N cannot be directly measured at whole-watershed scales; hence, N source attribution estimates at scales beyond a small catchment must rely on models. Although such estimates have been accomplished using individual N loading models, there has not yet been a comparison of source attribution by multiple regional- and continental-scale models. We compared results from two models applied at large spatial scales: Nutrient Export from WatershedS (NEWS) and SPAtially Referenced Regressions On Watersheds (SPARROW). Despite widely divergent approaches to source attribution, NEWS and SPARROW identified the same dominant sources of N for 65% of the modeled drainage area of the continental US. Human activities accounted for over two-thirds of N delivered to the coastal zone. Regionally, the single largest sources of N predicted by both models reflect land-use patterns across the country. Sewage was an important source in densely populated regions along the east and west coasts of the US. Fertilizer and livestock manure were dominant in the Mississippi River Basin, where the bulk of agricultural areas are located. Run-off from undeveloped areas was the largest source of N delivered to coastal areas in the northwestern US. Our analysis shows that comparisons of source apportionment between models can increase confidence in modeled output by revealing areas of agreement and disagreement. We found predictions for agriculture and atmospheric deposition to be comparable between models; however, attribution to sewage was greater by SPARROW than by NEWS, while the reverse was true for natural N sources. Such differences in predictions resulted from differences in model structure and sources of input data. Nonetheless, model comparisons provide strong evidence that anthropogenic activities have a profound effect on N delivered to coastal areas of the US, especially along the Atlantic coast and Gulf of Mexico.

Nitrogen and phosphorus in streams of the Great Miami River Basin, Ohio, 1998-2000

USGS Publications Warehouse

Reutter, David C.

2003-01-01

Sources and loads of nitrogen and phosphorus in streams of the Great Miami River Basin were evaluated as part of the National Water-Quality Assessment program. Water samples were collected by the U.S. Geological Survey from October 1998 through September 2000 (water years 1999 and 2000) at five locations in Ohio on a routine schedule and additionally during selected high streamflows. Stillwater River near Union, Great Miami River near Vandalia, and Mad River near Eagle City were selected to represent predominantly agricultural areas upstream from the Dayton metropolitan area. Holes Creek near Kettering is in the Dayton metropolitan area and was selected to represent an urban area in the Great Miami River Basin. Great Miami River at Hamilton is downstream from the Dayton and Hamilton-Middletown metropolitan areas and was selected to represent mixed agricultural and urban land uses of the Great Miami River Basin. Inputs of nitrogen and phosphorus to streams from point and nonpoint sources were estimated for the three agricultural basins and for the Great Miami River Basin as a whole. Nutrient inputs from point sources were computed from the facilities that discharge one-half million gallons or more per day into streams of the Great Miami River Basin. Nonpoint-source inputs estimated in this report are atmospheric deposition and commercial-fertilizer and manure applications. Loads of ammonia, nitrate, total nitrogen, orthophosphate, and total phosphorus from the five sites were computed with the ESTIMATOR program. The computations show nitrate to be the primary component of instream nitrogen loads, and particulate phosphorus to be the primary component of instream phosphorus loads. The Mad River contributed the smallest loads of total nitrogen and total phosphorus to the study area upstream from Dayton, whereas the Upper Great Miami River (upstream from Vandalia) contributed the largest loads of total nitrogen and total phosphorus to the Great Miami River Basin upstream from Dayton. An evaluation of monthly mean loads shows that nutrient loads were highest during winter 1999 and lowest during the drought of summer and autumn 1999. During the 1999 drought, point sources were the primary contributors of nitrogen and phosphorus loads to most of the study area. Nonpoint sources, however, were the primary contributors of nitrogen and phosphorus loads during months of high streamflow. Nonpoint sources were also the primary contributors of nitrogen loads to the Mad River during the 1999 drought, owing to unusually large amounts of ground-water discharge to the stream. The Stillwater River Basin had the highest nutrient yields in the study area during months of high streamflow; however, the Mad River Basin had the highest yields of all nutrients except ammonia during the months of the 1999 drought. The high wet-weather yields in the Stillwater River Basin were caused by agricultural runoff, whereas high yields in the Mad River Basin during drought resulted from the large, sustained contribution of ground water to streamflow throughout the year. In the basins upstream from Dayton, an estimated 19 to 25 percent of the nonpoint source of nitrogen and 4 to 5 percent of the nonpoint source of phosphorus that was deposited or applied to the land was transported into streams.

Air Quality Impact of Diffuse and Inefficient Combustion Emissions in Africa (DICE-Africa).

PubMed

Marais, Eloise A; Wiedinmyer, Christine

2016-10-04

Anthropogenic pollution in Africa is dominated by diffuse and inefficient combustion sources, as electricity access is low and motorcycles and outdated cars proliferate. These sources are missing, out-of-date, or misrepresented in state-of-the-science emission inventories. We address these deficiencies with a detailed inventory of Diffuse and Inefficient Combustion Emissions in Africa (DICE-Africa) for 2006 and 2013. Fuelwood for energy is the largest emission source in DICE-Africa, but grows from 2006 to 2013 at a slower rate than charcoal production and use, and gasoline and diesel for motorcycles, cars, and generators. Only kerosene use and gas flaring decline. Increase in emissions from 2006 to 2013 in this work is consistent with trends in satellite observations of formaldehyde and NO 2 , but much slower than the explosive growth projected with a fuel consumption model. Seasonal biomass burning is considered a large pollution source in Africa, but we estimate comparable emissions of black carbon and higher emissions of nonmethane volatile organic compounds from DICE-Africa. Nitrogen oxide (NO x ≡ NO + NO 2 ) emissions are much lower than from biomass burning. We use GEOS-Chem to estimate that the largest contribution of DICE-Africa to annual mean surface fine particulate matter (PM 2.5 ) is >5 μg m -3 in populous Nigeria.

Modeling study of biomass burning plumes and their impact on urban air quality; a case study of Santiago de Chile

NASA Astrophysics Data System (ADS)

Cuchiara, Gustavo C.; Rappenglück, Bernhard; Angelica Rubio, Maria; Lissi, Eduardo; Gramsch, Ernesto; Garreaud, Rene D.

2017-04-01

Wildfires are a significant direct source of atmospheric pollutants; on a global scale biomass burning is believed to be the largest source of primary fine particles in the atmosphere and the second largest source of trace gases after anthropogenic emission sources. During the summer of 2014, an intense forest and dry pasture wildfire occurred nearby the city of Santiago de Chile. The biomass-burning plume was transported towards the metropolitan area of Santiago and exacerbated the air quality in this region. In this study, we investigated this wildfire event using a forward plume-rise and a chemistry (WRF/Chem) simulation. These data sets provided an opportunity to validate a regional air-quality simulation over Santiago, and a unique case to assess the performance of biomass burning plume modeling in complex topography and validated against an established air quality network. The results from both meteorological and air quality models provide insights about the transport of biomass-burning plumes from the wildfire region towards the metropolitan region of Santiago de Chile. We studied a seven-day period between January 01-07, 2014, and the impact of biomass burning plume emissions estimated by Fire Inventory from NCAR version 1 (FINNv1) on the air quality of Santiago de Chile.

MODELING PHOTOCHEMISTRY AND AEROSOL FORMATION IN POINT SOURCE PLUMES WITH THE CMAQ PLUME-IN-GRID

EPA Science Inventory

Emissions of nitrogen oxides and sulfur oxides from the tall stacks of major point sources are important precursors of a variety of photochemical oxidants and secondary aerosol species. Plumes released from point sources exhibit rather limited dimensions and their growth is gradu...

MODELING THE RESPONSE OF FISH POPULATIONS TO EUTROPHICATION

EPA Science Inventory

Eutrophication resulting from nonpoint source pollution is one of the largest environmental problems in lakes and reservoirs around the world. Two characteristics of eutrophication, decreased dissolved oxygen and increased concentration of ammonia, are known to affect fishes, yet...

X-ray Point Source Populations in Spiral and Elliptical Galaxies

NASA Astrophysics Data System (ADS)

Colbert, E.; Heckman, T.; Weaver, K.; Ptak, A.; Strickland, D.

2001-12-01

In the years of the Einstein and ASCA satellites, it was known that the total hard X-ray luminosity from non-AGN galaxies was fairly well correlated with the total blue luminosity. However, the origin of this hard component was not well understood. Some possibilities that were considered included X-ray binaries, extended upscattered far-infrared light via the inverse-Compton process, extended hot 107 K gas (especially in ellipitical galaxies), or even an active nucleus. Now, for the first time, we know from Chandra images that a significant amount of the total hard X-ray emission comes from individual X-ray point sources. We present here spatial and spectral analyses of Chandra data for X-ray point sources in a sample of ~40 galaxies, including both spiral galaxies (starbursts and non-starbursts) and elliptical galaxies. We shall discuss the relationship between the X-ray point source population and the properties of the host galaxies. We show that the slopes of the point-source X-ray luminosity functions are different for different host galaxy types and discuss possible reasons why. We also present detailed X-ray spectral analyses of several of the most luminous X-ray point sources (i.e., IXOs, a.k.a. ULXs), and discuss various scenarios for the origin of the X-ray point sources.

Determination of efficiency of an aged HPGe detector for gaseous sources by self absorption correction and point source methods

NASA Astrophysics Data System (ADS)

Sarangapani, R.; Jose, M. T.; Srinivasan, T. K.; Venkatraman, B.

2017-07-01

Methods for the determination of efficiency of an aged high purity germanium (HPGe) detector for gaseous sources have been presented in the paper. X-ray radiography of the detector has been performed to get detector dimensions for computational purposes. The dead layer thickness of HPGe detector has been ascertained from experiments and Monte Carlo computations. Experimental work with standard point and liquid sources in several cylindrical geometries has been undertaken for obtaining energy dependant efficiency. Monte Carlo simulations have been performed for computing efficiencies for point, liquid and gaseous sources. Self absorption correction factors have been obtained using mathematical equations for volume sources and MCNP simulations. Self-absorption correction and point source methods have been used to estimate the efficiency for gaseous sources. The efficiencies determined from the present work have been used to estimate activity of cover gas sample of a fast reactor.

Discrimination between diffuse and point sources of arsenic at Zimapán, Hidalgo state, Mexico.

PubMed

Sracek, Ondra; Armienta, María Aurora; Rodríguez, Ramiro; Villaseñor, Guadalupe

2010-01-01

There are two principal sources of arsenic in Zimapán. Point sources are linked to mining and smelting activities and especially to mine tailings. Diffuse sources are not well defined and are linked to regional flow systems in carbonate rocks. Both sources are caused by the oxidation of arsenic-rich sulfidic mineralization. Point sources are characterized by Ca-SO(4)-HCO(3) ground water type and relatively enriched values of deltaD, delta(18)O, and delta(34)S(SO(4)). Diffuse sources are characterized by Ca-Na-HCO(3) type of ground water and more depleted values of deltaD, delta(18)O, and delta(34)S(SO(4)). Values of deltaD and delta(18)O indicate similar altitude of recharge for both arsenic sources and stronger impact of evaporation for point sources in mine tailings. There are also different values of delta(34)S(SO(4)) for both sources, presumably due to different types of mineralization or isotopic zonality in deposits. In Principal Component Analysis (PCA), the principal component 1 (PC1), which describes the impact of sulfide oxidation and neutralization by the dissolution of carbonates, has higher values in samples from point sources. In spite of similar concentrations of As in ground water affected by diffuse sources and point sources (mean values 0.21 mg L(-1) and 0.31 mg L(-1), respectively, in the years from 2003 to 2008), the diffuse sources have more impact on the health of population in Zimapán. This is caused by the extraction of ground water from wells tapping regional flow system. In contrast, wells located in the proximity of mine tailings are not generally used for water supply.

Interplanetary Scintillation studies with the Murchison Wide-field Array III: Comparison of source counts and densities for radio sources and their sub-arcsecond components at 162 MHz

NASA Astrophysics Data System (ADS)

Chhetri, R.; Ekers, R. D.; Morgan, J.; Macquart, J.-P.; Franzen, T. M. O.

2018-06-01

We use Murchison Widefield Array observations of interplanetary scintillation (IPS) to determine the source counts of point (<0.3 arcsecond extent) sources and of all sources with some subarcsecond structure, at 162 MHz. We have developed the methodology to derive these counts directly from the IPS observables, while taking into account changes in sensitivity across the survey area. The counts of sources with compact structure follow the behaviour of the dominant source population above ˜3 Jy but below this they show Euclidean behaviour. We compare our counts to those predicted by simulations and find a good agreement for our counts of sources with compact structure, but significant disagreement for point source counts. Using low radio frequency SEDs from the GLEAM survey, we classify point sources as Compact Steep-Spectrum (CSS), flat spectrum, or peaked. If we consider the CSS sources to be the more evolved counterparts of the peaked sources, the two categories combined comprise approximately 80% of the point source population. We calculate densities of potential calibrators brighter than 0.4 Jy at low frequencies and find 0.2 sources per square degrees for point sources, rising to 0.7 sources per square degree if sources with more complex arcsecond structure are included. We extrapolate to estimate 4.6 sources per square degrees at 0.04 Jy. We find that a peaked spectrum is an excellent predictor for compactness at low frequencies, increasing the number of good calibrators by a factor of three compared to the usual flat spectrum criterion.

Exopolysaccharides from yeast: insight into optimal conditions for biosynthesis, chemical composition and functional properties - review.

PubMed

Gientka, Iwona; Błażejak, Stanisław; Stasiak-Różańska, Lidia; Chlebowska-Śmigiel, Anna

2015-01-01

xopolysaccharides (EPS) are not a well-established group of metabolites. An industrial scale    of this EPS production is limited mainly by low yield biosynthesis. Until now, enzymes and biosynthesis pathways, as well as the role of regulatory genes, have not been described. Some of yeast EPS show antitumor, immunostimulatory and antioxidant activity. Others, absorb heavy metals and can function as bioactive components of food. Also, the potential of yeast EPS as thickeners or stabilizers can be found. Optimal conditions for the biosynthesis of yeast exopolysaccharides require strong oxygenation and low temperature of the culture, due to the physiology of the producer strains. The medium should contain sucrose as a carbon source and ammonium sulfate as inorganic nitrogen source, wherein the C:N ratio in the substrate should be 15:1. The cultures are long and the largest accumulation of polymers is observed after 4 or 5 days of culturing. The structure of yeast EPS is complex which affects the strain and culture condition. The EPS from yeast are linear mannans, pullulan, glucooligosaccharides, galactooligosaccharides and other heteropolysaccharides containing α-1,2; α-1,3; α-1,6; β-1,3; β-1,4 bonds. Mannose and glucose have the largest participation of carbohydrates for. t exopolysaccharides (EPS) are not a well-established group of metabolites. An industrial scale    of this EPS production is limited mainly by low yield biosynthesis. Until now, enzymes and biosynthesis pathways, as well as the role of regulatory genes, have not been described. Some of yeast EPS show antitumor, immunostimulatory and antioxidant activity. Others, absorb heavy metals and can function as bioactive components of food. Also, the potential of yeast EPS as thickeners or stabilizers can be found. Optimal conditions for the biosynthesis of yeast exopolysaccharides require strong oxygenation and low temperature of the culture, due to the physiology of the producer strains. The medium should contain sucrose as a carbon source and ammonium sulfate as inorganic nitrogen source, wherein the C:N ratio in the substrate should be 15:1. The cultures are long and the largest accumulation of polymers is observed after 4 or 5 days of culturing. The structure of yeast EPS is complex which affects the strain and culture condition. The EPS from yeast are linear mannans, pullulan, glucooligosaccharides, galactooligosaccharides and other heteropolysaccharides containing α-1,2; α-1,3; α-1,6; β-1,3; β-1,4 bonds. Mannose and glucose have the largest participation of carbohydrates formin. t exopolysaccharides (EPS) are not a well-established group of metabolites. An industrial scale    of this EPS production is limited mainly by low yield biosynthesis. Until now, enzymes and biosynthesis pathways, as well as the role of regulatory genes, have not been described. Some of yeast EPS show antitumor, immunostimulatory and antioxidant activity. Others, absorb heavy metals and can function as bioactive components of food. Also, the potential of yeast EPS as thickeners or stabilizers can be found. Optimal conditions for the biosynthesis of yeast exopolysaccharides require strong oxygenation and low temperature of the culture, due to the physiology of the producer strains. The medium should contain sucrose as a carbon source and ammonium sulfate as inorganic nitrogen source, wherein the C:N ratio in the substrate should be 15:1. The cultures are long and the largest accumulation of polymers is observed after 4 or 5 days of culturing. The structure of yeast EPS is complex which affects the strain and culture condition. The EPS from yeast are linear mannans, pullulan, glucooligosaccharides, galactooligosaccharides and other heteropolysaccharides containing α-1,2; α-1,3; α-1,6; β-1,3; β-1,4 bonds. Mannose and glucose have the largest participation of carbohydrates forming EPS.

Fault parameters and macroseismic observations of the May 10, 1997 Ardekul-Ghaen earthquake

NASA Astrophysics Data System (ADS)

Amini, H.; Zare, M.; Ansari, A.

2018-01-01

The Ardekul (Zirkuh) earthquake (May 10, 1997) is the largest recent earthquake that occurred in the Ardekul-Ghaen region of Eastern Iran. The greatest destruction was concentrated around Ardekul, Haji-Abad, Esfargh, Pishbar, Bashiran, Abiz-Qadim, and Fakhr-Abad (completely destroyed). The total surface fault rupture was about 125 km with the longest un-interrupted segment in the south of the region. The maximum horizontal and vertical displacements were reported in Korizan and Bohn-Abad with about 210 and 70 cm, respectively; moreover, other building damages and environmental effects were also reported for this earthquake. In this study, the intensity value XI on the European Macroseismic Scale (EMS) and Environmental Seismic Intensity (ESI) scale was selected for this earthquake according to the maximum effects on macroseismic data points affected by this earthquake. Then, according to its macroseismic data points of this earthquake and Boxer code, some macroseismic parameters including magnitude, location, source dimension, and orientation of this earthquake were also estimated at 7.3, 33.52° N-59.99° E, 75 km long and 21 km wide, and 152°, respectively. As the estimated macroseismic parameters are consistent with the instrumental ones (Global Centroid Moment Tensor (GCMT) location and magnitude equal 33.58° N-60.02° E, and 7.2, respectively), this method and dataset are suggested not only for other instrumental earthquakes, but also for historical events.

Sources of Information and Behavioral Patterns in Online Health Forums: Observational Study

PubMed Central

Friede, Tim; Grabowski, Jens; Koschack, Janka; Makedonski, Philip; Himmel, Wolfgang

2014-01-01

Background Increasing numbers of patients are raising their voice in online forums. This shift is welcome as an act of patient autonomy, reflected in the term “expert patient”. At the same time, there is considerable concern that patients can be easily misguided by pseudoscientific research and debate. Little is known about the sources of information used in health-related online forums, how users apply this information, and how they behave in such forums. Objective The intent of the study was to identify (1) the sources of information used in online health-related forums, and (2) the roles and behavior of active forum visitors in introducing and disseminating this information. Methods This observational study used the largest German multiple sclerosis (MS) online forum as a database, analyzing the user debate about the recently proposed and controversial Chronic Cerebrospinal Venous Insufficiency (CCSVI) hypothesis. After extracting all posts and then filtering relevant CCSVI posts between 01 January 2008 and 17 August 2012, we first identified hyperlinks to scientific publications and other information sources used or referenced in the posts. Employing k-means clustering, we then analyzed the users’ preference for sources of information and their general posting habits. Results Of 139,912 posts from 11,997 threads, 8628 posts discussed or at least mentioned CCSVI. We detected hyperlinks pointing to CCSVI-related scientific publications in 31 posts. In contrast, 2829 different URLs were posted to the forum, most frequently referring to social media, such as YouTube or Facebook. We identified a total of 6 different roles of hyperlink posters including Social Media Fans, Organization Followers, and Balanced Source Users. Apart from the large and nonspecific residual category of the “average user”, several specific behavior patterns were identified, such as the small but relevant groups of CCSVI-Focused Responders or CCSVI Activators. Conclusions The bulk of the observed contributions were not based on scientific results, but on various social media sources. These sources seem to contain mostly opinions and personal experience. A small group of people with distinct behavioral patterns played a core role in fuelling the discussion about CCSVI. PMID:24425598

Open Source Tools for Numerical Simulation of Urban Greenhouse Gas Emissions

NASA Astrophysics Data System (ADS)

Nottrott, A.; Tan, S. M.; He, Y.

2016-12-01

There is a global movement toward urbanization. Approximately 7% of the global population lives in just 28 megacities, occupying less than 0.1% of the total land area used by human activity worldwide. These cities contribute a significant fraction of the global budget of anthropogenic primary pollutants and greenhouse gasses. The 27 largest cities consume 9.9%, 9.3%, 6.7% and 3.0% of global gasoline, electricity, energy and water use, respectively. This impact motivates novel approaches to quantify and mitigate the growing contribution of megacity emissions to global climate change. Cities are characterized by complex topography, inhomogeneous turbulence, and variable pollutant source distributions. These features create a scale separation between local sources and urban scale emissions estimates known as the Grey-Zone. Modern computational fluid dynamics (CFD) techniques provide a quasi-deterministic, physically based toolset to bridge the scale separation gap between source level dynamics, local measurements, and urban scale emissions inventories. CFD has the capability to represent complex building topography and capture detailed 3D turbulence fields in the urban boundary layer. This presentation discusses the application of OpenFOAM to urban CFD simulations of natural gas leaks in cities. OpenFOAM is an open source software for advanced numerical simulation of engineering and environmental fluid flows. When combined with free or low cost computer aided drawing and GIS, OpenFOAM generates a detailed, 3D representation of urban wind fields. OpenFOAM was applied to model methane (CH4) emissions from various components of the natural gas distribution system, to investigate the impact of urban meteorology on mobile CH4 measurements. The numerical experiments demonstrate that CH4 concentration profiles are highly sensitive to the relative location of emission sources and buildings. Sources separated by distances of 5-10 meters showed significant differences in vertical dispersion of the plume due to building wake effects. The OpenFOAM flow fields were combined with an inverse, stochastic dispersion model to quantify and visualize the sensitivity of point sensors to upwind sources in various built environments.

Point-and-Click Pedagogy: Is It Effective for Teaching Information Technology?

ERIC Educational Resources Information Center

Angolia, Mark G.; Pagliari, Leslie R.

2016-01-01

This paper assesses the effectiveness of the adoption of curriculum content developed and supported by a global academic university-industry alliance sponsored by one of the world's largest information technology software providers. Academic alliances promote practical and future-oriented education while providing access to proprietary software…

40 CFR 90.327 - Sampling system requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... each component (pump, sample line section, filters, and so forth) in the heated portion of the sampling... largest thermal mass and the oven temperature need be measured. (b) If water is removed by condensation, monitor the sample gas temperature or sample dew point either within the water trap or downstream. It may...

40 CFR 90.327 - Sampling system requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... each component (pump, sample line section, filters, and so forth) in the heated portion of the sampling... largest thermal mass and the oven temperature need be measured. (b) If water is removed by condensation, monitor the sample gas temperature or sample dew point either within the water trap or downstream. It may...

40 CFR 90.327 - Sampling system requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... each component (pump, sample line section, filters, and so forth) in the heated portion of the sampling... largest thermal mass and the oven temperature need be measured. (b) If water is removed by condensation, monitor the sample gas temperature or sample dew point either within the water trap or downstream. It may...

Material Cultural Correlates of the Athapaskan Expansion: A Cross-Disciplinary Approach

ERIC Educational Resources Information Center

Wilson, Joseph Andrew Park

2011-01-01

Contrary to stereotypes of proto-Athapaskan culture as simplistic and archaic, evidence points to a sophisticated web of late prehistoric Asian-Athapaskan interactions. A holistic assessment of Athapaskan migrations in the context of the transpacific Dene-Yeneseian phylum (the largest, fastest pedestrian language spread on earth) sees…

Runoff Characterization and Variations at McMurdo Station, Antarctica

DTIC Science & Technology

2014-05-13

Boulevard Arlington, VA 22230 Laura Elliot and Corey Chan Antarctic Support Contract 7400 S. Tucson Way Centennial , CO 08112 Michael Diamond...then along the road and down Hut Point Road. Sub-basin 2 has the largest area and encompasses the majority of the snowfield and the depression above

Study: Third of Big Groundwater Basins in Distress

NASA Image and Video Library

2015-06-16

Groundwater storage trends for Earth's 37 largest aquifers from UCI-led study using NASA GRACE data (2003-2013). Of these, 21 have exceeded sustainability tipping points and are being depleted, with 13 considered significantly distressed, threatening regional water security and resilience. http://photojournal.jpl.nasa.gov/catalog/PIA19685

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aartsen, M. G.; Abraham, K.; Ackermann, M.

Observation of a point source of astrophysical neutrinos would be a “smoking gun” signature of a cosmic-ray accelerator. While IceCube has recently discovered a diffuse flux of astrophysical neutrinos, no localized point source has been observed. Previous IceCube searches for point sources in the southern sky were restricted by either an energy threshold above a few hundred TeV or poor neutrino angular resolution. Here we present a search for southern sky point sources with greatly improved sensitivities to neutrinos with energies below 100 TeV. By selecting charged-current ν{sub μ} interacting inside the detector, we reduce the atmospheric background while retainingmore » efficiency for astrophysical neutrino-induced events reconstructed with sub-degree angular resolution. The new event sample covers three years of detector data and leads to a factor of 10 improvement in sensitivity to point sources emitting below 100 TeV in the southern sky. No statistically significant evidence of point sources was found, and upper limits are set on neutrino emission from individual sources. A posteriori analysis of the highest-energy (∼100 TeV) starting event in the sample found that this event alone represents a 2.8 σ deviation from the hypothesis that the data consists only of atmospheric background.« less

DISCRIMINATION OF NATURAL AND NON-POINT SOURCE EFFECTS FROM ANTHROGENIC EFFECTS AS REFLECTED IN BENTHIC STATE IN THREE ESTUARIES IN NEW ENGLAND

EPA Science Inventory

In order to protect estuarine resources, managers must be able to discern the effects of natural conditions and non-point source effects, and separate them from multiple anthropogenic point source effects. Our approach was to evaluate benthic community assemblages, riverine nitro...

40 CFR 409.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Beet Sugar Processing... a point source where the sugar beet processing capacity of the point source does not exceed 1090 kkg... results, in whole or in part, from barometric condensing operations and any other beet sugar processing...

40 CFR 409.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Beet Sugar Processing... a point source where the sugar beet processing capacity of the point source does not exceed 1090 kkg... results, in whole or in part, from barometric condensing operations and any other beet sugar processing...

40 CFR 409.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Beet Sugar Processing... a point source where the sugar beet processing capacity of the point source does not exceed 1090 kkg... results, in whole or in part, from barometric condensing operations and any other beet sugar processing...

40 CFR 409.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Beet Sugar Processing... a point source where the sugar beet processing capacity of the point source does not exceed 1090 kkg... results, in whole or in part, from barometric condensing operations and any other beet sugar processing...

40 CFR 409.13 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS SUGAR PROCESSING POINT SOURCE CATEGORY Beet Sugar Processing... a point source where the sugar beet processing capacity of the point source does not exceed 1090 kkg... results, in whole or in part, from barometric condensing operations and any other beet sugar processing...

Source phase shift - A new phenomenon in wave propagation due to anelasticity. [in free oscillations of earth model

NASA Technical Reports Server (NTRS)

Buland, R.; Yuen, D. A.; Konstanty, K.; Widmer, R.

1985-01-01

The free oscillations of an anelastic earth model due to earthquakes were calculated directly by means of the correspondence principle from wave propagation theory. The formulation made it possible to find the source phase which is not predictable using first order perturbation theory. The predicted source phase was largest for toroidal modes with source components proportional to the radial strain scalar instead of the radial displacement scalar. The source phase increased in relation to the overtone number. In addition, large relative differences were found in the excitation modulus and the phase when the elastic excitation was small. The effect was sufficient to bias estimates of source properties and elastic structure.

Occurrence of Surface Water Contaminations: An Overview

NASA Astrophysics Data System (ADS)

Shahabudin, M. M.; Musa, S.

2018-04-01

Water is a part of our life and needed by all organisms. As time goes by, the needs by human increased transforming water quality into bad conditions. Surface water contaminated in various ways which is pointed sources and non-pointed sources. Pointed sources means the source are distinguished from the source such from drains or factory but the non-pointed always occurred in mixed of elements of pollutants. This paper is reviewing the occurrence of the contaminations with effects that occurred around us. Pollutant factors from natural or anthropology factors such nutrients, pathogens, and chemical elements contributed to contaminations. Most of the effects from contaminated surface water contributed to the public health effects also to the environments.

A metabolic simulator for unmanned testing of breathing apparatuses in hyperbaric conditions.

PubMed

Frånberg, Oskar; Loncar, Mario; Larsson, Åke; Ornhagen, Hans; Gennser, Mikael

2014-11-01

A major part of testing of rebreather apparatuses for underwater diving focuses on the oxygen dosage system. A metabolic simulator for testing breathing apparatuses was built and evaluated. Oxygen consumption was achieved through catalytic combustion of propene. With an admixture of carbon dioxide in the propene fuel, the system allowed the respiratory exchange ratio to be set freely within human variability and also made it possible to increase test pressures above the condensation pressure of propene. The system was tested by breathing ambient air in a pressure chamber with oxygen uptake (Vo₂) ranging from 1-4 L · min(-1), tidal volume (VT) from 1-3 L, breathing frequency (f) of 20 and 25 breaths/min, and chamber pressures from 100 to 670 kPa. The measured end-tidal oxygen concentration (Fo₂) was compared to calculated end-tidal Fo₂. The largest average difference in end-tidal Fo₂during atmospheric pressure conditions was 0.63%-points with a 0.28%-point average difference during the whole test. During hyperbaric conditions with pressures ranging from 100 to 670 kPa, the largest average difference in Fo₂was 1.68%-points seen during compression from 100 kPa to 400 kPa and the average difference in Fo₂during the whole test was 0.29%-points. In combination with a breathing simulator simulating tidal breathing, the system can be used for dynamic continuous testing of breathing equipment with changes in VT, f, Vo2, and pressure.

2011 Radioactive Materials Usage Survey for Unmonitored Point Sources

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sturgeon, Richard W.

This report provides the results of the 2011 Radioactive Materials Usage Survey for Unmonitored Point Sources (RMUS), which was updated by the Environmental Protection (ENV) Division's Environmental Stewardship (ES) at Los Alamos National Laboratory (LANL). ES classifies LANL emission sources into one of four Tiers, based on the potential effective dose equivalent (PEDE) calculated for each point source. Detailed descriptions of these tiers are provided in Section 3. The usage survey is conducted annually; in odd-numbered years the survey addresses all monitored and unmonitored point sources and in even-numbered years it addresses all Tier III and various selected other sources.more » This graded approach was designed to ensure that the appropriate emphasis is placed on point sources that have higher potential emissions to the environment. For calendar year (CY) 2011, ES has divided the usage survey into two distinct reports, one covering the monitored point sources (to be completed later this year) and this report covering all unmonitored point sources. This usage survey includes the following release points: (1) all unmonitored sources identified in the 2010 usage survey, (2) any new release points identified through the new project review (NPR) process, and (3) other release points as designated by the Rad-NESHAP Team Leader. Data for all unmonitored point sources at LANL is stored in the survey files at ES. LANL uses this survey data to help demonstrate compliance with Clean Air Act radioactive air emissions regulations (40 CFR 61, Subpart H). The remainder of this introduction provides a brief description of the information contained in each section. Section 2 of this report describes the methods that were employed for gathering usage survey data and for calculating usage, emissions, and dose for these point sources. It also references the appropriate ES procedures for further information. Section 3 describes the RMUS and explains how the survey results are organized. The RMUS Interview Form with the attached RMUS Process Form(s) provides the radioactive materials survey data by technical area (TA) and building number. The survey data for each release point includes information such as: exhaust stack identification number, room number, radioactive material source type (i.e., potential source or future potential source of air emissions), radionuclide, usage (in curies) and usage basis, physical state (gas, liquid, particulate, solid, or custom), release fraction (from Appendix D to 40 CFR 61, Subpart H), and process descriptions. In addition, the interview form also calculates emissions (in curies), lists mrem/Ci factors, calculates PEDEs, and states the location of the critical receptor for that release point. [The critical receptor is the maximum exposed off-site member of the public, specific to each individual facility.] Each of these data fields is described in this section. The Tier classification of release points, which was first introduced with the 1999 usage survey, is also described in detail in this section. Section 4 includes a brief discussion of the dose estimate methodology, and includes a discussion of several release points of particular interest in the CY 2011 usage survey report. It also includes a table of the calculated PEDEs for each release point at its critical receptor. Section 5 describes ES's approach to Quality Assurance (QA) for the usage survey. Satisfactory completion of the survey requires that team members responsible for Rad-NESHAP (National Emissions Standard for Hazardous Air Pollutants) compliance accurately collect and process several types of information, including radioactive materials usage data, process information, and supporting information. They must also perform and document the QA reviews outlined in Section 5.2.6 (Process Verification and Peer Review) of ES-RN, 'Quality Assurance Project Plan for the Rad-NESHAP Compliance Project' to verify that all information is complete and correct.« less

Use of Standalone GPS for Approach with Vertical Guidance.

DOT National Transportation Integrated Search

2001-01-22

The accuracy of GPS has improved dramatically over the past year with the removal of Selective Availability. The largest error source now is the ionosphere which can be removed in the future when the additional civil frequencies become available. Pre...

Transport outlook 2008 : focusing on CO2 emissions from road vehicles

DOT National Transportation Integrated Search

2008-05-01

This short outlook is designed to test the potential for key policy instruments for mitigating emissions from road transport, and particularly from light duty vehicles, the largest source of CO2 emissions from transport. It also examines uncertaintie...

Measuring Spatial Variability of Vapor Flux to Characterize Vadose-zone VOC Sources: Flow-cell Experiments

DOE PAGES

Mainhagu, Jon; Morrison, C.; Truex, Michael J.; ...

2014-08-05

A method termed vapor-phase tomography has recently been proposed to characterize the distribution of volatile organic contaminant mass in vadose-zone source areas, and to measure associated three-dimensional distributions of local contaminant mass discharge. The method is based on measuring the spatial variability of vapor flux, and thus inherent to its effectiveness is the premise that the magnitudes and temporal variability of vapor concentrations measured at different monitoring points within the interrogated area will be a function of the geospatial positions of the points relative to the source location. A series of flow-cell experiments was conducted to evaluate this premise. Amore » well-defined source zone was created by injection and extraction of a non-reactive gas (SF6). Spatial and temporal concentration distributions obtained from the tests were compared to simulations produced with a mathematical model describing advective and diffusive transport. Tests were conducted to characterize both areal and vertical components of the application. Decreases in concentration over time were observed for monitoring points located on the opposite side of the source zone from the local–extraction point, whereas increases were observed for monitoring points located between the local–extraction point and the source zone. We found that the results illustrate that comparison of temporal concentration profiles obtained at various monitoring points gives a general indication of the source location with respect to the extraction and monitoring points.« less

Long-period Ground Motion Characteristics Inside and Outside of the Osaka Basin during the 2011 Great Tohoku Earthquake and Its Largest Aftershock

NASA Astrophysics Data System (ADS)

Sato, K.; Iwata, T.; Asano, K.; Kubo, H.; Aoi, S.

2013-12-01

The 2011 great Tohoku earthquake (Mw 9.0) occurred on March 11, 2011, and the largest aftershock (Mw 7.7) at the region adjacent to south boundary of the mainshock's source region. Long-period ground motions (1-10s) of large amplitude were observed in the Osaka sedimentary basin about 550-800km away from the source regions during both events. We studied propagation and site characteristics of these ground motions, and found some common features between these two events in the Osaka basin. (1) The amplitude of horizontal components of the ground motion at the site-specific period is amplified at each sedimentary station. The predominant period is around 7s in the bayside area where the largest pSv were observed. (2) The velocity Fourier spectra have their peak values around 7s at the bedrock sites surrounding the Osaka basin. (3) Two remarkable wave packets separated by 30s propagating from stations around the Nobi plain to the bedrock sites near the Osaka basin were seen in the pasted-up velocity waveforms from the source regions to the Osaka basin for both events (Sato et al., 2012). Therefore, large long-period ground motions in the Osaka basin are generated by the combination of propagation-path and basin effects. Firstly, we simulate ground motions due to the largest aftershock using three-dimensional FDM (GMS; Aoi and Fujiwara, 1999). The reason we focus on the largest aftershock is that this event has a relatively small rupture area and simple rupture process compared to the mainshock. The source model is based on the model estimated by Kubo et al. (2013). The velocity structure model is a three-dimensional velocity structure based on the Japan Integrated Velocity Structure Model (Koketsu et al., 2012) and the layer of Vs 350m/s in this model is replaced with one of Vs 500m/s. The minimum effective period in this computation is 3s. Then, we compare synthetic waveforms with observed ones. At CHBH14, the nearest station to the source and 60km away from the epicenter, the synthetic waveforms of the period-band 5-50s, where Kubo et al. (2013) studied, fit well to the observed ones. However, in our target period-band 5-8s, the earlier portion of the synthetic waveform of the main packet has smaller amplitude than the observation. At the bedrock sites near the Osaka basin, two wave packets which are appeared in the observation are qualitatively reproduced in the synthetics. However, the amplitudes are not well reproduced. Moreover, the amplitude ratio of horizontal components of synthetics between the rock and the bayside stations is underestimated compared to the observed one. Improvements of the source and velocity structure models for propagation-path and basin are needed. For that sake, we will analyze the characteristics of the synthetic waveforms, study how those wave packets are generated, and discuss the discrepancy between the synthetic and observed waveforms. We will also simulate the ground motion for the mainshock to study propagation characteristics of the mainshock. ACKNOWLEDGEMENTS We used strong motion data recorded by K-NET, KiK-net and F-net of NIED, CEORKA, BRI, JMA, and Osaka prefecture. GMS provided by NIED is used for the computation.

Erratic blocks in NW Poland - geological heritage, conservation and geotourism promotion

NASA Astrophysics Data System (ADS)

Górska-Zabielska, Maria

2015-04-01

Big glacial erratic blocks, transported between 20 ka and 14 ka BP from Scandinavia are still present in the fields and forest of the north-western part of Poland. They present mainly magmatic and metamorphic petrographic types. Among them the most important are indicator erratics, which point to a distinct source region in Sweden, Finland or within the Baltic Sea. The largest boulders, sometimes shrouded in legend, have been protected for ages as natural monuments. Others still wait for such an attention. The largest erratic block in Poland ("Trigław") is located in a small town Tychowo (53°55'42″N 16°15'29″E) in the Middle Pomerania. It is a gneiss with no features pointing to a distinct Scandinavian provenance. Its measurements are: height 7,8 m (3,8 m above surface), length 13,7 m, width 9,3 m, volume around 520 m3, weight 1430 tons. The biggest sedimentary boulder, sandstone ("Mszczonowski Głaz"), is located in a Zawada village (51°54`51,1"N 20°27`16,5"E) in the centre of Poland (beyond the scope of the presentation). Its measurements are: height 3 m, length 12 m, width 3 m, volume around 57 m3, weight 160 tons. The presentation shows the biggest and most interesting Scandinavian boulders blocks from north-western part of Poland, their geological heritage and role, that they play in a local geotourism promotion. Apart from their location in situ, the boulders are also available ex situ, i.e. in erratic gardens. These collections of rocks accompany seats of local nature museums or national parks offices. Also other usage of erratics (stony buildings and road/pavements, fences), known for ages, will be presented. Erratic blocks are favorite destinations for tourists who follow geotouristic trails. The most valuable for a geotourism are these geosites, which are equipped in a board informing about the genesis and geologic value of an erratic. The simpler and more intelligible language, the bigger didactic and touristic value of a geosite.

Large Historical Tsunamigenic Earthquakes in Italy: The Neglected Tsunami Research Point of View

NASA Astrophysics Data System (ADS)

Armigliato, A.; Tinti, S.; Pagnoni, G.; Zaniboni, F.

2015-12-01

It is known that tsunamis are rather rare events, especially when compared to earthquakes, and the Italian coasts are no exception. Nonetheless, a striking evidence is that 6 out of 10 earthquakes occurred in the last thousand years in Italy, and having equivalent moment magnitude equal or larger than 7 where accompanied by destructive or heavily damaging tsunamis. If we extend the lower limit of the equivalent moment magnitude down to 6.5 the percentage decreases (around 40%), but is still significant. Famous events like those occurred on 30 July 1627 in Gargano, on 11 January 1693 in eastern Sicily, and on 28 December 1908 in the Messina Straits are part of this list: they were all characterized by maximum run-ups of several meters (13 m for the 1908 tsunami), significant maximum inundation distances, and large (although not precisely quantifiable) numbers of victims. Further evidences provided in the last decade by paleo-tsunami deposit analyses help to better characterize the tsunami impact and confirm that none of the cited events can be reduced to local or secondary effects. Proper analysis and simulation of available tsunami data would then appear as an obvious part of the correct definition of the sources responsible for the largest Italian tsunamigenic earthquakes, in a process in which different datasets analyzed by different disciplines must be reconciled rather than put into contrast with each other. Unfortunately, macroseismic, seismic and geological/geomorphological observations and data typically are assigned much heavier weights, and in-land faults are often assigned larger credit than the offshore ones, even when evidence is provided by tsunami simulations that they are not at all capable of justifying the observed tsunami effects. Tsunami generation is imputed a-priori to only supposed, and sometimes even non-existing, submarine landslides. We try to summarize the tsunami research point of view on the largest Italian historical tsunamigenic earthquakes; we highlight the open problems, and suggest that tsunami observations and simulations can contribute towards their solution. This study is funded in the frame of the EU Project called ASTARTE - Assessment, STrategy And Risk reduction for Tsunamis in Europe. Grant 603839, 7th FP (ENV.2013.6.4-3).

Improvements and limitations on understanding of atmospheric processes of Fukushima Daiichi NPS radioactivity

NASA Astrophysics Data System (ADS)

Yamazawa, Hiromi; Terasaka, Yuta; Mizutani, Kenta; Sugiura, Hiroki; Hirao, Shigekazu

2017-04-01

Understanding on the release of radioactivity into the atmosphere from the accidental units of Fukushima Daiichi Nuclear Power Station have been improved owing to recent analyses of atmospheric concentrations of radionuclide. Our analysis of gamma-ray spectra from monitoring posts located about 100 km to the south of the site revealed temporal changes of atmospheric concentrations of several key nuclides including noble gas Xe-133 in addition to radio-iodine and cesium nuclides, including I-131 and Cs-137, at a 10 minute interval. By using the atmospheric concentration data, in combination with an inverse atmospheric transport modelling with a Bayesian statistical method, a modification was proposed for the widely used Katata's source term. A source term for Xe-133 was also proposed. Although the atmospheric concentration data and the source terms help us understand the atmospheric transport processes of radionuclides, they still have significant uncertainty due to limitations in availability of the concentration data. There still remain limitations in the atmospheric transport modeling. The largest uncertainty in the model is in the deposition processes. It had been pointed out that, in the 100 km range from the accidental site, there were locations at which the ambient dose rate significantly increased a few hours before precipitation detectors recorded the start of rain. According to our analysis, the dose rate increase was not directly caused by the air-borne radioactivity but by deposition. This phenomenon can be attributed to a deposition process in which evaporating precipitation enhances efficiency of deposition even in a case where no precipitation is observed at ground level.

Assessment of macrophyte, heavy metal, and nutrient concentrations in the water of the Nairobi River, Kenya.

PubMed

Njuguna, Samwel Maina; Yan, Xue; Gituru, Robert Wahiti; Wang, Qingfeng; Wang, Jun

2017-08-16

Nairobi River tributaries are the main source of the Athi River. The Athi River basin is the fourth largest and important drainage system in Kenya covering 650 km and with a drainage area of 70,000 km 2 . Its water is used downstream by about four million people not only for irrigation but also for domestic purposes. However, its industrial, raw sewer, and agricultural pollution is alarming. In order to understand distribution and concentration of heavy metals and nutrients in the water of Nairobi River, 28 water samples were collected in the rainy season (October) of 2015 and dry season (June) of 2016. Cd, Cu, Cr, Zn, As, Pb, Fe, Ni, Mn, NO 3 - , and TP were analyzed. Only Cr, Pb, Fe, and Mn had concentrations exceeding the WHO permissible limit for drinking water. Out of the 28 sites examined in the study, one site had Pb exceeding the WHO recommended level. Similarly, three sites exceeded the same level for Cr. Only three sites were within the WHO permissible limits for drinking water for Mn while just four sites were within USEPA limit for Fe. Industrial effluent, domestic sewerage, agricultural activities, and solid waste were the main sources of pollution. Significant spatial variation of both heavy metals and nutrients concentration was observed and emanated from point source pollution. Eleven out of 31 macrophytes species that were identified along the river and its tributaries are effective heavy metal and nutrient bioaccumulators and may be used in phytoremediation.

Small river plumes off the northeastern coast of the Black Sea under average climatic and flooding discharge conditions

NASA Astrophysics Data System (ADS)

Osadchiev, Alexander; Korshenko, Evgeniya

2017-06-01

This study focuses on the impact of discharges of small rivers on the delivery and fate of fluvial water and suspended matter at the northeastern part of the Black Sea under different local precipitation conditions. Several dozens of mountainous rivers flow into the sea at the study region, and most of them, except for several of the largest, have little annual runoff and affect adjacent coastal waters to a limited extent under average climatic conditions. However, the discharges of these small rivers are characterized by a quick response to precipitation events and can significantly increase during and shortly after heavy rains, which are frequent in the considered area. The delivery and fate of fluvial water and terrigenous sediments at the study region, under average climatic and rain-induced flooding conditions, were explored and compared using in situ data, satellite imagery, and numerical modeling. It was shown that the point-source spread of continental discharge dominated by several large rivers under average climatic conditions can change to the line-source discharge from numerous small rivers situated along the coast in response to heavy rains. The intense line-source runoff of water and suspended sediments forms a geostrophic alongshore current of turbid and freshened water, which induces the intense transport of suspended and dissolved constituents discharged with river waters in a northwestern direction. This process significantly influences water quality and causes active sediment load at large segments of the narrow shelf at the northeastern part of the Black Sea compared to average climatic discharge conditions.

Small river plumes near the north-eastern coast of the Black Sea under climatic mean and flooding discharge conditions

NASA Astrophysics Data System (ADS)

Osadchiev, Alexander; Korshenko, Evgeniya

2017-04-01

The study is focused on the impact of discharge from small rivers on propagation and final location of fluvial waters and suspended matter at the north-eastern part of the Black Sea under different local precipitation conditions. Several dozens of mountainous rivers inflow into the sea at the studied region and most of them, except the several largest of them, have small annual runoff and limitedly affect adjacent coastal waters under climatic mean conditions. However, discharges of these small rivers are characterized by quick response to precipitation events and can dramatically increase during and shortly after heavy rains, which are frequent in the area under consideration. Propagation and final location of fluvial waters and terrigenous sediments at the studied region under climatic mean and rain-induced flooding conditions were explored and compared using in situ data, satellite imagery and numerical modelling. It was shown that the point-source spread of continental discharge dominated by several large rivers during climatic mean conditions can change to the line-source discharge from numerous small rivers situated along the coast in response to heavy rains. Intense line-source runoff of water and suspended sediments form a geostrophic alongshore current of turbid and freshened water, which induces intense transport of suspended and dissolved constituents discharged with river waters in a north-western direction. This process significantly influences water quality and causes active sediment load at large segments of narrow shelf at the north-eastern part of the Black Sea as compared to climatic mean discharge conditions.

Reconstructed Sediment Mobilization Processes in a Large Reservoir Using Short Sediment Cores

NASA Astrophysics Data System (ADS)

Cockburn, J.; Feist, S.

2014-12-01

Williston Reservoir in northern British Columbia (56°10'31"N, 124°06'33") was formed when the W.A.C. Bennett Dam was created in the late 1960s, is the largest inland body of water in BC and facilitates hydroelectric power generation. Annually the reservoir level rises and lowers with the hydroelectric dam operation, and this combined with the inputs from several river systems (Upper Peace, Finlay, Parsnip, and several smaller creeks) renews suspended sediment sources. Several short-cores retrieved from shallow bays of the Finlay Basin reveal near-annual sedimentary units and distinct patterns related to both hydroclimate variability and the degree to which the reservoir lowered in a particular year. Thin section and sedimentology from short-cores collected in three bays are used to evaluate sediment mobilization processes. The primary sediment sources in each core location is linked to physical inputs from rivers draining into the bays, aeolian contributions, and reworked shoreline deposits as water levels fluctuate. Despite uniform water level lowering across the reservoir, sediment sequences differed at each site, reflecting the local stream inputs. However, distinct organic-rich units, facilitated correlation across the sites. Notable differences in particle size distributions from each core points to important aeolian derived sediment sources. Using these sedimentary records, we can evaluate the processes that contribute to sediment deposition in the basin. This work will contribute to decisions regarding reservoir water levels to reduce adverse impacts on health, economic activities and recreation in the communities along the shores of the reservoir.

Developing a comprehensive framework for eutrophication management in off-stream artificial lakes

NASA Astrophysics Data System (ADS)

Khorasani, Hamed; Kerachian, Reza; Malakpour-Estalaki, Siamak

2018-07-01

In this paper, a comprehensive and interdisciplinary framework for management of eutrophication in off-stream artificial lakes in semi-arid and arid regions is proposed. Identification of the lake's water resources system components and stakeholders, simulation of Phosphorus (P) export from upstream watershed, simulation of the lake water quality as well as simulation of water demands and supply, development of management scenarios for the lake and selecting the best scenario using social choice methods (i.e. discrete and fuzzy Borda counts) are the four main parts of the framework. The proposed framework is applied on Chitgar Artificial Lake (ChAL), the largest intra-urban artificial lake in Tehran which has been constructed in 2010-2013 for recreational purposes. The Load Apportionment Model (LAM) is used for the simulation of P loads from the point and non-point (diffusive) sources and the LakeMab model is used for the simulation of P dynamics in the lake. The management scenarios contain optimized rule curves for water intake/outtake blended with P management plans (i.e. removal of point sources of P load in the upstream watershed, construction of a hydroponic bio-filter or an advanced water treatment plant beside the lake for reduction of external loading of P and recycling lake water, alum treatment of lake sediments for controlling the internal loading of P as well as construction of a dry detention basin). The most preferred scenarios selected by the discrete Borda count are the low-cost alum treatment and dry detention basin, while the most preferred scenario according to fuzzy Borda count, which considers the uncertainty of model inputs, is the costly water treatment plant. In all preferred scenarios, water intake is conducted from flood flows in order to avoid conflict with downstream agricultural demands. In addition to decentralized decision making and stakeholders' participation, the proposed framework promotes the integration of the technical aspects such as the role of internal loading in lake eutrophication and separation of flood and non-flood flows in the off-stream lakes' systems.

Point and Condensed Hα Sources in the Interior of M33

NASA Astrophysics Data System (ADS)

Moody, J. Ward; Hintz, Eric G.; Roming, Peter; Joner, Michael D.; Bucklein, Brian

2017-01-01

A variety of interesting objects such as Wolf-Rayet stars, tight OB associations, planetary nebula, x-ray binaries, etc. can be discovered as point or condensed sources in Hα surveys. How these objects distribute through a galaxy sheds light on the galaxy star formation rate and history, mass distribution, and dynamics. The nearby galaxy M33 is an excellent place to study the distribution of Hα-bright point sources in a flocculant spiral galaxy. We have reprocessed an archived WIYN continuum-subtracted Hα image of the inner 6.5' of the nearby galaxy M33 and, employing both eye and machine searches, have tabulated sources with a flux greater than 1 x 10-15 erg cm-2sec-1. We have identified 152 unresolved point sources and 122 marginally resolved condensed sources, 38 of which have not been previously cataloged. We present a map of these sources and discuss their probable identifications.

Perspectives on individual to ensembles of ambient fine and ultrafine particles and their sources

NASA Astrophysics Data System (ADS)

Bein, Keith James

By combining Rapid Single-ultrafine-particle Mass Spectrometry (RSMS) measurements during the Pittsburgh Supersite experiment with a large array of concurrent PM, gas and meteorological data, a synthesis of data and analyses is employed to characterize sources, emission trends and dynamics of ambient fine and ultrafine particles. Combinatorial analyses elicit individual to ensemble descriptions of particles, their sources, their changes in state from atmospheric processing and the scales of motion driving their transport and dynamics. Major results include (1) Particle size and composition are strong indicators of sources/source categories and real-time measurements allow source attribution at the single particle and point source level. (2) Single particle source attribution compares well to factor analysis of chemically-speciated bulk phase data and both resulted in similar conclusions but independently revealed new sources. (3) RSMS data can quantitatively estimate composition-resolved, number-based particle size distribution. Comparison to mass-based data yielded new information about physical and chemical properties of particles and instrument sensitivity. (4) Source-specific signatures and real-time monitoring allow passing plumes to be tracked and characterized. (5) The largest of three identified coal combustion sources emits ˜ 2.4 x 10 17 primary submicron particles per second. (6) Long-range transport has a significant impact on the eastern U.S. including specific influences of eight separate wildfire events. (7) Pollutant dynamics in the Pittsburgh summertime air shed, and Northeastern U.S., is characterized by alternating periods of stagnation and cleansing. The eight wildfire events were detected in between seven successive stagnation events. (8) Connections exist between boreal fire activity, southeast subsiding transport of the emissions, alternating periods of stagnation and cleansing at the receptor and the structure and propagation of extratropical waves. (9) Wildfire emissions can severely impact preexisting pollutant concentrations and physical and chemical processes at the receptor. (10) High-severity crown fires in boreal Canada emit ˜ 1.2 x 1015 particles/kg biomass burned. (11) In 1998, wildfire activity in the circumpolar boreal forest emitted ˜ 8 x 1026 particles, representing ˜ 14% of global wildland fire emissions. Results and conclusions address future scientific objectives in understanding effects of particles on human health and global climate change.

A guide to differences between stochastic point-source and stochastic finite-fault simulations

USGS Publications Warehouse

Atkinson, G.M.; Assatourians, K.; Boore, D.M.; Campbell, K.; Motazedian, D.

2009-01-01

Why do stochastic point-source and finite-fault simulation models not agree on the predicted ground motions for moderate earthquakes at large distances? This question was posed by Ken Campbell, who attempted to reproduce the Atkinson and Boore (2006) ground-motion prediction equations for eastern North America using the stochastic point-source program SMSIM (Boore, 2005) in place of the finite-source stochastic program EXSIM (Motazedian and Atkinson, 2005) that was used by Atkinson and Boore (2006) in their model. His comparisons suggested that a higher stress drop is needed in the context of SMSIM to produce an average match, at larger distances, with the model predictions of Atkinson and Boore (2006) based on EXSIM; this is so even for moderate magnitudes, which should be well-represented by a point-source model. Why? The answer to this question is rooted in significant differences between point-source and finite-source stochastic simulation methodologies, specifically as implemented in SMSIM (Boore, 2005) and EXSIM (Motazedian and Atkinson, 2005) to date. Point-source and finite-fault methodologies differ in general in several important ways: (1) the geometry of the source; (2) the definition and application of duration; and (3) the normalization of finite-source subsource summations. Furthermore, the specific implementation of the methods may differ in their details. The purpose of this article is to provide a brief overview of these differences, their origins, and implications. This sets the stage for a more detailed companion article, "Comparing Stochastic Point-Source and Finite-Source Ground-Motion Simulations: SMSIM and EXSIM," in which Boore (2009) provides modifications and improvements in the implementations of both programs that narrow the gap and result in closer agreement. These issues are important because both SMSIM and EXSIM have been widely used in the development of ground-motion prediction equations and in modeling the parameters that control observed ground motions.

ObsPy: A Python Toolbox for Seismology

NASA Astrophysics Data System (ADS)

Krischer, Lion; Megies, Tobias; Sales de Andrade, Elliott; Barsch, Robert; MacCarthy, Jonathan

2017-04-01

In recent years the Python ecosystem evolved into one of the most powerful and productive scientific environments across disciplines. ObsPy (https://www.obspy.org) is a fully community-driven, open-source project dedicated to providing a bridge for seismology into that ecosystem. It does so by offering Read and write support for essentially every commonly used data format in seismology with a unified interface and automatic format detection. This includes waveform data (MiniSEED, SAC, SEG-Y, Reftek, …) as well as station (SEED, StationXML, …) and event meta information (QuakeML, ZMAP, …). Integrated access to the largest data centers, web services, and real-time data streams (FDSNWS, ArcLink, SeedLink, ...). A powerful signal processing toolbox tuned to the specific needs of seismologists. Utility functionality like travel time calculations with the TauP method, geodetic functions, and data visualizations. ObsPy has been in constant development for more than seven years and is developed and used by scientists around the world with successful applications in all branches of seismology. Additionally it nowadays serves as the foundation for a large number of more specialized packages. This presentation will give a short overview of the capabilities of ObsPy and point out several representative or new use cases. Additionally we will discuss the road ahead as well as the long-term sustainability of open-source scientific software.

Advanced Variance Reduction Strategies for Optimizing Mesh Tallies in MAVRIC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peplow, Douglas E.; Blakeman, Edward D; Wagner, John C

2007-01-01

More often than in the past, Monte Carlo methods are being used to compute fluxes or doses over large areas using mesh tallies (a set of region tallies defined on a mesh that overlays the geometry). For problems that demand that the uncertainty in each mesh cell be less than some set maximum, computation time is controlled by the cell with the largest uncertainty. This issue becomes quite troublesome in deep-penetration problems, and advanced variance reduction techniques are required to obtain reasonable uncertainties over large areas. The CADIS (Consistent Adjoint Driven Importance Sampling) methodology has been shown to very efficientlymore » optimize the calculation of a response (flux or dose) for a single point or a small region using weight windows and a biased source based on the adjoint of that response. This has been incorporated into codes such as ADVANTG (based on MCNP) and the new sequence MAVRIC, which will be available in the next release of SCALE. In an effort to compute lower uncertainties everywhere in the problem, Larsen's group has also developed several methods to help distribute particles more evenly, based on forward estimates of flux. This paper focuses on the use of a forward estimate to weight the placement of the source in the adjoint calculation used by CADIS, which we refer to as a forward-weighted CADIS (FW-CADIS).« less

Impacts by point and diffuse micropollutant sources on the stream water quality at catchment scale

NASA Astrophysics Data System (ADS)

Petersen, M. F.; Eriksson, E.; Binning, P. J.; Bjerg, P. L.

2012-04-01

The water quality of surface waters is threatened by multiple anthropogenic pollutants and the large variety of pollutants challenges the monitoring and assessment of the water quality. The aim of this study was to characterize and quantify both point and diffuse sources of micropollutants impacting the water quality of a stream at catchment scale. Grindsted stream in western Jutland, Denmark was used as a study site. The stream passes both urban and agricultural areas and is impacted by severe groundwater contamination in Grindsted city. Along a 12 km reach of Grindsted stream, the potential pollution sources were identified including a pharmaceutical factory site with a contaminated old drainage ditch, two waste deposits, a wastewater treatment plant, overflow structures, fish farms, industrial discharges and diffuse agricultural and urban sources. Six water samples were collected along the stream and analyzed for general water quality parameters, inorganic constituents, pesticides, sulfonamides, chlorinated solvents, BTEXs, and paracetamol and ibuprofen. The latter two groups were not detected. The general water quality showed typical conditions for a stream in western Jutland. Minor impacts by releases of organic matter and nutrients were found after the fish farms and the waste water treatment plant. Nickel was found at concentrations 5.8 - 8.8 μg/l. Nine pesticides and metabolites of both agricultural and urban use were detected along the stream; among these were the two most frequently detected and some rarely detected pesticides in Danish water courses. The concentrations were generally consistent with other findings in Danish streams and in the range 0.01 - 0.09 μg/l; except for metribuzin-diketo that showed high concentrations up to 0.74 μg/l. The groundwater contamination at the pharmaceutical factory site, the drainage ditch and the waste deposits is similar in composition containing among others sulfonamides and chlorinated solvents (including vinyl chloride). Vinyl chloride concentrations surpassed Danish stream water quality criteria with a factor 10. The largest chemical impact occurs at the reach downstream Grindsted city revealing that the main contaminant groundwater discharge zones are found here. The contaminant plume from the factory site north of the stream is known to impact the stream whereas the impact by the old landfill south of the stream remains to be assessed. A conceptual model of the chemical impacts by the identified sources was made, and high impact was assigned to the contaminant plume from the factory site and to the diffuse sources of urban-use and agricultural pesticides. The next step will be a quantification of the sources, which will be presented at the conference.

Toward an annual estimate of methane emissions from Lake Erie

NASA Astrophysics Data System (ADS)

Fernandez, J.; Townsend-Small, A.

2017-12-01

Lake Erie is the shallowest, warmest, and most eutrophic of all of the North American Great Lakes. The central basin of Lake Erie exhibits seasonally hypoxic bottom waters, which contributes to biological methane (CH4) production. Leaks from extensive natural gas wells and pipelines in Canadian waters are a potential source of thermogenic CH4 to the lake. The shallow western basin lacks water column hypoxia, but experiences increasingly frequent algal blooms and hypoxic sediments. Our past research, focused on the central basin, indicated that Lake Erie is a positive source of CH4 during late summer (August - September), emitting 1.3 ± 0.6 × 105 kg CH4-C day. Here, we present a seasonal dataset of CH4 fluxes measured throughout a 16-month period starting in the spring of 2015 and ending late summer in 2016 to estimate an annual lake wide CH4 emission. Our results indicate that the western basin experienced the greatest CH4 emissions, and the highest rates of CH4 flux co-occur with the highest rates of nutrient loading and largest algal blooms near the mouth of the Maumee River. Winter CH4 fluxes were minimal and similar throughout the lake, indicating that natural gas wells are a minimal source of CH4 emissions. Emissions were highest in August and tapered off through the fall and winter, rising again in spring. The estimated annual CH4 emission in Lake Erie was 4.41 × 107 kg CH4-C yr-1. We compared this to other CH4 sources in Michigan and Ohio in the USEPA Greenhouse Gas Reporting Program Database, and found that Lake Erie is second largest emitter of CH4 in Ohio (a landfill in Cincinnati is a larger source), and the largest in Michigan. Recent work has shown that eutrophication in lakes such as Lake Erie may be on the rise due to climate change induced increases in precipitation. If so, these large CH4 emissions may have positive feedback consequences to climate warming. Therefore, more research is needed to indicate whether or not these CH4 emissions are increasing.

X-ray Point Source Populations in Spiral and Elliptical Galaxies

NASA Astrophysics Data System (ADS)

Colbert, E.; Heckman, T.; Weaver, K.; Strickland, D.

2002-01-01

The hard-X-ray luminosity of non-active galaxies has been known to be fairly well correlated with the total blue luminosity since the days of the Einstein satellite. However, the origin of this hard component was not well understood. Some possibilities that were considered included X-ray binaries, extended upscattered far-infrared light via the inverse-Compton process, extended hot 107 K gas (especially in ellipitical galaxies), or even an active nucleus. Chandra images of normal, elliptical and starburst galaxies now show that a significant amount of the total hard X-ray emission comes from individual point sources. We present here spatial and spectral analyses of the point sources in a small sample of Chandra obervations of starburst galaxies, and compare with Chandra point source analyses from comparison galaxies (elliptical, Seyfert and normal galaxies). We discuss possible relationships between the number and total hard luminosity of the X-ray point sources and various measures of the galaxy star formation rate, and discuss possible options for the numerous compact sources that are observed.

Vector image method for the derivation of elastostatic solutions for point sources in a plane layered medium. Part 1: Derivation and simple examples

NASA Technical Reports Server (NTRS)

Fares, Nabil; Li, Victor C.

1986-01-01

An image method algorithm is presented for the derivation of elastostatic solutions for point sources in bonded halfspaces assuming the infinite space point source is known. Specific cases were worked out and shown to coincide with well known solutions in the literature.

40 CFR 414.100 - Applicability; description of the subcategory of direct discharge point sources that do not use...

Code of Federal Regulations, 2010 CFR

2010-07-01

... subcategory of direct discharge point sources that do not use end-of-pipe biological treatment. 414.100... AND STANDARDS ORGANIC CHEMICALS, PLASTICS, AND SYNTHETIC FIBERS Direct Discharge Point Sources That Do Not Use End-of-Pipe Biological Treatment § 414.100 Applicability; description of the subcategory of...

Better Assessment Science Integrating Point and Non-point Sources (BASINS)

EPA Pesticide Factsheets

Better Assessment Science Integrating Point and Nonpoint Sources (BASINS) is a multipurpose environmental analysis system designed to help regional, state, and local agencies perform watershed- and water quality-based studies.

THE BRIGHTEST CLUSTER GALAXY IN A85: THE LARGEST CORE KNOWN SO FAR

DOE Office of Scientific and Technical Information (OSTI.GOV)

López-Cruz, O.; Añorve, C.; Ibarra-Medel, H. J.

2014-11-10

We have found that the brightest cluster galaxy (BCG) in A85, Holm 15A, displays the largest core known so far. Its cusp radius, r {sub γ} = 4.57 ± 0.06 kpc (4.''26 ± 0.''06), is more than 18 times larger than the mean for BCGs and ≳ 1 kpc larger than A2261-BCG, hitherto the largest-cored BCG. Holm 15A hosts the luminous amorphous radio source 0039-095B and has the optical signature of a LINER. Scaling laws indicate that this core could host a supermassive black hole (SMBH) of mass M {sub •} ∼ (10{sup 9}-10{sup 11}) M {sub ☉}. We suggestmore » that cores this large represent a relatively short phase in the evolution of BCGs, whereas the masses of their associated SBMH might be set by initial conditions.« less

Investigating energy consumption of coastal vacation rental homes

NASA Astrophysics Data System (ADS)

Myers, Sam

In 2007, vacation rental properties in the United States accounted for more than 22% of the domestic lodging market. These properties are a unique segment of the lodging industry due to their residential design and commercial use. Coastal vacation rental properties represent the largest supply, demand and value of the nation's vacation rental supply. In the case of North Carolina's Outer Banks, tourism is the area's largest source of income, with vacation real estate agencies being the largest accommodation provider. This study uses a multiple regression analysis to investigate the energy consumption of 30 vacation rental homes on Hatteras Island. Hatteras Island's abundant supply of vacation rental homes provided a diverse sample to study energy consumption with a wide range of houses regarding size, age, and location. Since very little research has been conducted on the energy consumption of vacation rental homes, this study aims to contribute detailed information regarding the energy consumption of unique accommodation sector.

Magnitudes, nature, and effects of point and nonpoint discharges in the Chattahoochee River basin, Atlanta to West Point Dam, Georgia

USGS Publications Warehouse

Stamer, J.K.; Cherry, R.N.; Faye, R.E.; Kleckner, R.L.

1978-01-01

On an average annual basis and during the storm period of March 12-15, 1976, nonpoint-source loads for most constituents were larger than point-source loads at the Whitesburg station, located on the Chattahoochee River about 40 miles downstream from Atlanta, GA. Most of the nonpoint-source constituent loads in the Atlanta to Whitesburg reach were from urban areas. Average annual point-source discharges accounted for about 50 percent of the dissolved nitrogen, total nitrogen, and total phosphorus loads and about 70 percent of the dissolved phosphorus loads at Whitesburg. During a low-flow period, June 1-2, 1977, five municipal point-sources contributed 63 percent of the ultimate biochemical oxygen demand, and 97 percent of the ammonium nitrogen loads at the Franklin station, at the upstream end of West Point Lake. Dissolved-oxygen concentrations of 4.1 to 5.0 milligrams per liter occurred in a 22-mile reach of the river downstream from Atlanta due about equally to nitrogenous and carbonaceous oxygen demands. The heat load from two thermoelectric powerplants caused a decrease in dissolved-oxygen concentration of about 0.2 milligrams per liter. Phytoplankton concentrations in West Point Lake, about 70 miles downstream from Atlanta, could exceed three million cells per millimeter during extended low-flow periods in the summer with present point-source phosphorus loads. (Woodard-USGS)

Modelling of the estimated contributions of different sub-watersheds and sources to phosphorous export and loading from the Dongting Lake watershed, China.

PubMed

Hou, Ying; Chen, Weiping; Liao, Yuehua; Luo, Yueping

2017-11-03

Considerable growth in the economy and population of the Dongting Lake watershed in Southern China has increased phosphorus loading to the lake and resulted in a growing risk of lake eutrophication. This study aimed to reveal the spatial pattern and sources of phosphorus export and loading from the watershed. We applied an export coefficient model and the Dillon-Rigler model to quantify contributions of different sub-watersheds and sources to the total phosphorus (TP) export and loading in 2010. Together, the upper and lower reaches of the Xiang River watershed and the Dongting Lake Area contributed 60.9% of the TP exported from the entire watershed. Livestock husbandry appeared to be the largest anthropogenic source of TP, contributing more than 50% of the TP exported from each secondary sub-watersheds. The actual TP loading to the lake in 2010 was 62.9% more than the permissible annual TP loading for compliance with the Class III water quality standard for lakes. Three primary sub-watersheds-the Dongting Lake Area, the Xiang River, and the Yuan River watersheds-contributed 91.2% of the total TP loading. As the largest contributor among all sources, livestock husbandry contributed nearly 50% of the TP loading from the Dongting Lake Area and more than 60% from each of the other primary sub-watersheds. This study provides a methodology to identify the key sources and locations of TP export and loading in large lake watersheds. The study can provide a reference for the decision-making for controlling P pollution in the Dongting Lake watershed.

Unidentified point sources in the IRAS minisurvey

NASA Technical Reports Server (NTRS)

Houck, J. R.; Soifer, B. T.; Neugebauer, G.; Beichman, C. A.; Aumann, H. H.; Clegg, P. E.; Gillett, F. C.; Habing, H. J.; Hauser, M. G.; Low, F. J.

1984-01-01

Nine bright, point-like 60 micron sources have been selected from the sample of 8709 sources in the IRAS minisurvey. These sources have no counterparts in a variety of catalogs of nonstellar objects. Four objects have no visible counterparts, while five have faint stellar objects visible in the error ellipse. These sources do not resemble objects previously known to be bright infrared sources.

Source Process of the 2007 Niigata-ken Chuetsu-oki Earthquake Derived from Near-fault Strong Motion Data

NASA Astrophysics Data System (ADS)

Aoi, S.; Sekiguchi, H.; Morikawa, N.; Ozawa, T.; Kunugi, T.; Shirasaka, M.

2007-12-01

The 2007 Niigata-ken Chuetsu-oki earthquake occurred on July 16th, 2007, 10:13 JST. We performed a multi- time window linear waveform inversion analysis (Hartzell and Heaton, 1983) to estimate the rupture process from the near fault strong motion data of 14 stations from K-NET, KiK-net, F-net, JMA, and Niigata prefecture. The fault plane for the mainshock has not been clearly determined yet from the aftershock distribution, so that we performed two waveform inversions for north-west dipping fault (Model A) and south-east dipping fault (Model B). Their strike, dip, and rake are set to those of the moment tensor solutions by F-net. Fault plane model of 30 km length by 24 km width is set to cover aftershock distribution within 24 hours after the mainshock. Theoretical Green's functions were calculated by the discrete wavenumber method (Bouchon, 1981) and the R/T matrix method (Kennett, 1983) with the different stratified medium for each station based on the velocity structure including the information form the reflection survey and borehole logging data. Convolution of moving dislocation was introduced to represent the rupture propagation in an each subfault (Sekiguchi et al., 2002). The observed acceleration records were integrated into velocity except of F-net velocity data, and bandpass filtered between 0.1 and 1.0 Hz. We solved least-squared equation to obtain slip amount of each time window on each subfault to minimize squared residual of the waveform fitting between observed and synthetic waveforms. Both models provide moment magnitudes of 6.7. Regarding Model A, we obtained large slip in the south-west deeper part of the rupture starting point, which is close to Kashiwazaki-city. The second or third velocity pulses of observed velocity waveforms seem to be composed of slip from the asperity. Regarding Model B, we obtained large slip in the southwest shallower part of the rupture starting point, which is also close to Kashiwazaki-city. In both models, we found small slip near the rupture starting point, and largest slip at about ten kilometer in the south-west of the rupture starting point with the maximum slip of 2.3 and 2.5 m for Models A and B, respectively. The difference of the residual between observed and synthetic waveforms for both models is not significant, therefore it is difficult to conclude which fault plane is appropriate to explain. The estimated large-slip regions in the inverted source models with the Models A and B are located near the cross point of the two fault plane models, which should have similar radiation pattern. This situation may be one of the reasons why judgment of the fault plane orientation is such difficult. We need careful examinations not only strong motion data but also geodetic data to further explore the fault orientation and the source process of this earthquake.

A Comparative Analysis of Vibrio cholerae Contamination in Point-of-Drinking and Source Water in a Low-Income Urban Community, Bangladesh.

PubMed

Ferdous, Jannatul; Sultana, Rebeca; Rashid, Ridwan B; Tasnimuzzaman, Md; Nordland, Andreas; Begum, Anowara; Jensen, Peter K M

2018-01-01

Bangladesh is a cholera endemic country with a population at high risk of cholera. Toxigenic and non-toxigenic Vibrio cholerae ( V. cholerae ) can cause cholera and cholera-like diarrheal illness and outbreaks. Drinking water is one of the primary routes of cholera transmission in Bangladesh. The aim of this study was to conduct a comparative assessment of the presence of V. cholerae between point-of-drinking water and source water, and to investigate the variability of virulence profile using molecular methods of a densely populated low-income settlement of Dhaka, Bangladesh. Water samples were collected and tested for V. cholerae from "point-of-drinking" and "source" in 477 study households in routine visits at 6 week intervals over a period of 14 months. We studied the virulence profiles of V. cholerae positive water samples using 22 different virulence gene markers present in toxigenic O1/O139 and non-O1/O139 V. cholerae using polymerase chain reaction (PCR). A total of 1,463 water samples were collected, with 1,082 samples from point-of-drinking water in 388 households and 381 samples from 66 water sources. V. cholerae was detected in 10% of point-of-drinking water samples and in 9% of source water samples. Twenty-three percent of households and 38% of the sources were positive for V. cholerae in at least one visit. Samples collected from point-of-drinking and linked sources in a 7 day interval showed significantly higher odds ( P < 0.05) of V. cholerae presence in point-of-drinking compared to source [OR = 17.24 (95% CI = 7.14-42.89)] water. Based on the 7 day interval data, 53% (17/32) of source water samples were negative for V. cholerae while linked point-of-drinking water samples were positive. There were significantly higher odds ( p < 0.05) of the presence of V. cholerae O1 [OR = 9.13 (95% CI = 2.85-29.26)] and V. cholerae O139 [OR = 4.73 (95% CI = 1.19-18.79)] in source water samples than in point-of-drinking water samples. Contamination of water at the point-of-drinking is less likely to depend on the contamination at the water source. Hygiene education interventions and programs should focus and emphasize on water at the point-of-drinking, including repeated cleaning of drinking vessels, which is of paramount importance in preventing cholera.

Modeling deep brain stimulation: point source approximation versus realistic representation of the electrode

NASA Astrophysics Data System (ADS)

Zhang, Tianhe C.; Grill, Warren M.

2010-12-01

Deep brain stimulation (DBS) has emerged as an effective treatment for movement disorders; however, the fundamental mechanisms by which DBS works are not well understood. Computational models of DBS can provide insights into these fundamental mechanisms and typically require two steps: calculation of the electrical potentials generated by DBS and, subsequently, determination of the effects of the extracellular potentials on neurons. The objective of this study was to assess the validity of using a point source electrode to approximate the DBS electrode when calculating the thresholds and spatial distribution of activation of a surrounding population of model neurons in response to monopolar DBS. Extracellular potentials in a homogenous isotropic volume conductor were calculated using either a point current source or a geometrically accurate finite element model of the Medtronic DBS 3389 lead. These extracellular potentials were coupled to populations of model axons, and thresholds and spatial distributions were determined for different electrode geometries and axon orientations. Median threshold differences between DBS and point source electrodes for individual axons varied between -20.5% and 9.5% across all orientations, monopolar polarities and electrode geometries utilizing the DBS 3389 electrode. Differences in the percentage of axons activated at a given amplitude by the point source electrode and the DBS electrode were between -9.0% and 12.6% across all monopolar configurations tested. The differences in activation between the DBS and point source electrodes occurred primarily in regions close to conductor-insulator interfaces and around the insulating tip of the DBS electrode. The robustness of the point source approximation in modeling several special cases—tissue anisotropy, a long active electrode and bipolar stimulation—was also examined. Under the conditions considered, the point source was shown to be a valid approximation for predicting excitation of populations of neurons in response to DBS.

78 FR 20123 - Extension of the Designation of Honduras for Temporary Protected Status

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-03

... deforestation and erosion, and Honduras's largest source of fresh water (the Lago de Yojoa) is heavily polluted... the potable water distribution systems and sewage treatment facilities in urban and rural Honduras... situation with funds designated for [[Page 20125

Achieving sustainable cultivation of tomatoes

USDA-ARS?s Scientific Manuscript database

Preface Tomato is the second largest horticultural crop after potato, a worldwide industry valued at over $50 billion. In addition to being a cash crop for farmers, tomato fruit is a significant dietary source of micronutrients, vitamins and antioxidants in maintaining and enhancing human health. It...

Literature-based cheminformatics for research in chemical toxicity

EPA Science Inventory

PubMed is the largest freely available source of published literature available online with access to 27 million citations (as of October 2017). Contained within the literature is an abundance of information about the activity of chemicals in biological systems. Literature inform...

Minefields Associated with Mining Data from Peer-reviewed Literature

EPA Science Inventory

The USEPA’s ECOTOX database is the largest compilation of ecotoxicity study results, providing information on the adverse effects of single chemical stressors to ecologically relevant aquatic and terrestrial species. The primary source of data included in the ECOTOX database is t...

EPA Research Strengthens Great Lakes Restoration Initiative

EPA Science Inventory

As the largest group of freshwater lakes on Earth, the Great Lakes (Lakes Erie, Huron, Michigan, Ontario and Superior) are a source of economic prosperity, recreation and raw materials. Human activity, however, has resulted in pollution and other stressors. The Great Lakes curren...

Interdisciplinary Coordination Reviews: A Process to Reduce Construction Costs.

ERIC Educational Resources Information Center

Fewell, Dennis A.

1998-01-01

Interdisciplinary Coordination design review is instrumental in detecting coordination errors and omissions in construction documents. Cleansing construction documents of interdisciplinary coordination errors reduces time extensions, the largest source of change orders, and limits exposure to liability claims. Improving the quality of design…

Monoterpenes are the largest source of summertime organic aerosol in the southeastern United States

EPA Science Inventory

The chemical complexity of atmospheric organic aerosol (OA) has caused substantial uncertainties in understanding its origins and environmental impacts. Here, we provide constraints on OA origins through compositional characterization with molecular-level details. Our results sug...

Becoming weeds.

PubMed

Stewart, C Neal

2017-04-26

A new resequencing analysis of weedy rice (Oryza sativa L.) biotypes illuminates distinct evolutionary paths and outcomes of de-domestication and ferality. This largest effort to date in weedy plant genomics gives a better understanding of weediness while also providing a promising source of alleles for rice breeding.

Multiband super-resolution imaging of graded-index photonic crystal flat lens

NASA Astrophysics Data System (ADS)

Xie, Jianlan; Wang, Junzhong; Ge, Rui; Yan, Bei; Liu, Exian; Tan, Wei; Liu, Jianjun

2018-05-01

Multiband super-resolution imaging of point source is achieved by a graded-index photonic crystal flat lens. With the calculations of six bands in common photonic crystal (CPC) constructed with scatterers of different refractive indices, it can be found that the super-resolution imaging of point source can be realized by different physical mechanisms in three different bands. In the first band, the imaging of point source is based on far-field condition of spherical wave while in the second band, it is based on the negative effective refractive index and exhibiting higher imaging quality than that of the CPC. However, in the fifth band, the imaging of point source is mainly based on negative refraction of anisotropic equi-frequency surfaces. The novel method of employing different physical mechanisms to achieve multiband super-resolution imaging of point source is highly meaningful for the field of imaging.

NO2 and SO2 dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand.

PubMed

Chusai, Chatinai; Manomaiphiboon, Kasemsan; Saiyasitpanich, Phirun; Thepanondh, Sarawut

2012-08-01

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO2 and SO2 was conducted using the AERMOD model. The area-specific emission inventories of NOx and SO2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was Jbund, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration overfour selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations Jbfor each individual area, respectively. For AC-NO2, on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO2), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO2, biomass burning has the most influence in all impacted areas (>90%) exceptJor one residential area where on-road mobile is the largest (75%). For AC-SO2, the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO2, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group when managing air quality for the MA.

NO2 and SO2dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand.

PubMed

Chusai, Chatinai; Manomaiphiboon, Kasemsan; Saiyasitpanich, Phirun; Thepanondh, Sarawut

2012-08-01

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO 2 and SO 2 was conducted using the AERMOD model. The area-specific emission inventories of NO x and SO 2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was found, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration over four selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations for each individual area, respectively. For AC-NO 2 , on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO 2 ), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO 2 , biomass burning has the most influence in all impacted areas (>90%) except for one residential area where on-road mobile is the largest (75%). For AC-SO 2 , the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO 2 , the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group when managing air quality for the MA. [Box: see text] [Box: see text].

Long Term Temporal and Spectral Evolution of Point Sources in Nearby Elliptical Galaxies

NASA Astrophysics Data System (ADS)

Durmus, D.; Guver, T.; Hudaverdi, M.; Sert, H.; Balman, Solen

2016-06-01

We present the results of an archival study of all the point sources detected in the lines of sight of the elliptical galaxies NGC 4472, NGC 4552, NGC 4649, M32, Maffei 1, NGC 3379, IC 1101, M87, NGC 4477, NGC 4621, and NGC 5128, with both the Chandra and XMM-Newton observatories. Specifically, we studied the temporal and spectral evolution of these point sources over the course of the observations of the galaxies, mostly covering the 2000 - 2015 period. In this poster we present the first results of this study, which allows us to further constrain the X-ray source population in nearby elliptical galaxies and also better understand the nature of individual point sources.

Very Luminous X-ray Point Sources in Starburst Galaxies

NASA Astrophysics Data System (ADS)

Colbert, E.; Heckman, T.; Ptak, A.; Weaver, K. A.; Strickland, D.

Extranuclear X-ray point sources in external galaxies with luminosities above 1039.0 erg/s are quite common in elliptical, disk and dwarf galaxies, with an average of ~ 0.5 and dwarf galaxies, with an average of ~0.5 sources per galaxy. These objects may be a new class of object, perhaps accreting intermediate-mass black holes, or beamed stellar mass black hole binaries. Starburst galaxies tend to have a larger number of these intermediate-luminosity X-ray objects (IXOs), as well as a large number of lower-luminosity (1037 - 1039 erg/s) point sources. These point sources dominate the total hard X-ray emission in starburst galaxies. We present a review of both types of objects and discuss possible schemes for their formation.

A comparison of results from a hydrologic transport model (HSPF) with distributions of sulfate and mercury in a mine-impacted watershed in northeastern Minnesota.

PubMed

Berndt, Michael E; Rutelonis, Wes; Regan, Charles P

2016-10-01

The St. Louis River watershed in northeast Minnesota hosts a major iron mining district that has operated continuously since the 1890s. Concern exists that chemical reduction of sulfate that is released from mines enhances the methylation of mercury in the watershed, leading to increased mercury concentrations in St. Louis River fish. This study tests this idea by simulating the behavior of chemical tracers using a hydrologic flow model (Hydrologic Simulation Program FORTRAN; HSPF) and comparing the results with measured chemistry from several key sites located both upstream and downstream from the mining region. It was found that peaks in measured methylmercury (MeHg), total mercury (THg), dissolved organic carbon (DOC), and dissolved iron (Fe) concentrations correspond to periods in time when modeled recharge was dominated by active groundwater throughout the watershed. This helps explain why the timing and size of the MeHg peaks was nearly the same at sites located just upstream and downstream from the mining region. Both the modeled percentages of mine water and the measured sulfate concentrations were low and computed transit times were short for sites downstream from the mining region at times when measured MeHg reached its peak. Taken together, the data and flow model imply that MeHg is released into groundwater that recharges the river through riparian sediments following periods of elevated summer rainfall. The measured sulfate concentrations at the upstream site reached minimum concentrations of approximately 1 mg/L just as MeHg reached its peak, suggesting that reduction of sulfate from non-point sources exerts an important influence on MeHg concentrations at this site. While mines are the dominant source of sulfate to sites downstream from them, it appears that the background sulfate which is present at only 1-6 mg/L, has the largest influence on MeHg concentrations. This is because point sourced sulfate is transported generally under oxidized conditions and is not flushed through riparian sediments in a gaining stream watershed system. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Variability of the 2014-present inflation source at Mauna Loa volcano revealed using time-dependent modeling

NASA Astrophysics Data System (ADS)

Johanson, I. A.; Miklius, A.; Okubo, P.; Montgomery-Brown, E. K.

2017-12-01

Mauna Loa volcano is the largest active volcano on earth and in the 20thcentury produced roughly one eruption every seven years. The 33-year quiescence since its last eruption 1984 has been punctuated by three inflation episodes where magma likely entered the shallow plumbing system, but was not erupted. The most recent began in 2014 and is ongoing. Unlike prior inflation episodes, the current one is accompanied by a significant increase in shallow seismicity, a pattern that is similar to earlier pre-eruptive periods. We apply the Kalman filter based Network Inversion Filter (NIF) to the 2014-present inflation episode using data from a 27 station continuous GPS network on Mauna Loa. The model geometry consists of a point volume source and tabular, dike-like body, which have previously been shown to provide a good fit to deformation data from a 2004-2009 inflation episode. The tabular body is discretized into 1km x 1km segments. For each day, the NIF solves for the rates of opening on the tabular body segments (subject to smoothing and positivity constraints), volume change rate in the point source, and slip rate on a deep décollement fault surface, which is constrained to a constant (no transient slip allowed). The Kalman filter in the NIF provides for smoothing both forwards and backwards in time. The model shows that the 2014-present inflation episode occurred as several sub-events, rather than steady inflation. It shows some spatial variability in the location of the inflation sub-events. In the model, opening in the tabular body is initially concentrated below the volcano's summit, in an area roughly outlined by shallow seismicity. In October, 2015 opening in the tabular body shifts to be centered beneath the southwest portion of the summit and seismicity becomes concentrated in this area. By late 2016, the opening rate on the tabular body decreases and is once again under the central part of summit. This modeling approach has allowed us to track these features on a daily basis and capture the evolution of the inflation episode as it occurs.

The resolution of point sources of light as analyzed by quantum detection theory

NASA Technical Reports Server (NTRS)

Helstrom, C. W.

1972-01-01

The resolvability of point sources of incoherent light is analyzed by quantum detection theory in terms of two hypothesis-testing problems. In the first, the observer must decide whether there are two sources of equal radiant power at given locations, or whether there is only one source of twice the power located midway between them. In the second problem, either one, but not both, of two point sources is radiating, and the observer must decide which it is. The decisions are based on optimum processing of the electromagnetic field at the aperture of an optical instrument. In both problems the density operators of the field under the two hypotheses do not commute. The error probabilities, determined as functions of the separation of the points and the mean number of received photons, characterize the ultimate resolvability of the sources.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grant, Shanique L.; Kim, Myoungwoo; Lin, Peng

The Great Lakes eco-region is one of the largest sources of fresh water in North America; however it is chronically exposed to heavy metal loadings such as mercury. In this study a comprehensive model evaluation was conducted to determine mercury loadings to the Great Lakes. The study also evaluated the relative impact of anthropogenic mercury emissions from China, regional and global sources on deposition to the Great Lakes. For the 2005 study period, CMAQ 4.7.1 model estimated a total of 6.4 ± 0.5 metric tons of mercury deposited in the Great Lakes. The total deposition breakdown showed a net loadingmore » for Lake Superior of 1906 ± 246 kg/year which is the highest of all the lakes. Lake Michigan followed with 1645 ± 203 kg/year and 1511 ± 107 kg/year in Lake Huron. The lowest total deposition was seen in Lakes Erie and Ontario amassing annual totals of 837 ± 107 kg and 506 ± 63 kg, respectively. Wet and dry deposition of mercury were both significant pathways and exhibited strong seasonal variability with higher deposition occurring in the warmer months (June–November) and the lowest in winter. Wet deposition of RGM significantly influenced the deposition proportions accounting for roughly 90% of all mercury deposited. Of the three emission sources (global background, integrated planning management (IPM) and Chinese), global background concentrations represented the maximum impact to deposition loading in the Great Lakes, except for Lake Erie and parts of Lake Michigan. There was minimal seasonality for the global background, but differences in percentage contribution between dry (28–97%) and wet deposition (43–98%) was predicted. The contributions were seen mainly in the northern sections of the Great Lakes further away from IPM point sources. These findings suggest strong localized impact of IPM sources on the southernmost lakes. Deposition as a result of emissions from China exhibited seasonality in both wet and dry deposition and showed significant contributions ranging from 0.2 to 9%.« less

Investigating Diesel Engines as an Atmospheric Source of Isocyanic Acid in Urban Areas

NASA Astrophysics Data System (ADS)

Farmer, D.; Jathar, S.; Heppding, C.; Link, M.; Akherati, A.; Kleeman, M.; De Gouw, J. A.; Veres, P. R.; Roberts, J. M.

2017-12-01

Isocyanic acid (HNCO), an acidic gas found in tobacco smoke, urban environments and biomass burning-affected regions, has been linked to adverse health outcomes. Gasoline- and diesel-powered engines and biomass burning are known to emit HNCO and hypothesized to emit precursors such as amides that can photochemically react to produce HNCO in the atmosphere. Increasingly, diesel engines in developed countries like the United States are required to use Selective Catalytic Reduction (SCR) systems to reduce tailpipe emissions of oxides of nitrogen. SCR chemistry is known to produce HNCO as an intermediate product, and SCR systems have been implicated as an atmospheric source of HNCO. In this work, we measure HNCO emissions from an SCR system-equipped diesel engine and, in combination with earlier data, use a three-dimensional chemical transport model (CTM) to simulate the ambient concentrations and source/pathway contributions to HNCO in an urban environment. Engine tests were conducted at three different engine loads, using two different fuels and at multiple operating points. HNCO was measured using an acetate chemical ionization mass spectrometer. The diesel engine was found to emit primary HNCO (3-90 mg kg-fuel-1) but we did not find any evidence that the SCR system or other aftertreatment devices (i.e., oxidation catalyst and particle filter) produced or enhanced HNCO emissions. The CTM predictions compared well with the only available observational data sets for HNCO in urban areas but under-predicted the contribution from secondary processes. The comparison implied that diesel-powered engines were the largest source of HNCO in urban areas. The CTM also predicted that daily-averaged concentrations of HNCO reached a maximum of 110 pptv but were an order of magnitude lower than the 1 ppbv level that could be associated with physiological effects in humans. Precursor contributions from other combustion sources (gasoline and biomass burning) and wintertime conditions could enhance HNCO concentrations but need to be explored in future work.

Investigating diesel engines as an atmospheric source of isocyanic acid in urban areas

NASA Astrophysics Data System (ADS)

Jathar, Shantanu H.; Heppding, Christopher; Link, Michael F.; Farmer, Delphine K.; Akherati, Ali; Kleeman, Michael J.; de Gouw, Joost A.; Veres, Patrick R.; Roberts, James M.

2017-07-01

Isocyanic acid (HNCO), an acidic gas found in tobacco smoke, urban environments, and biomass-burning-affected regions, has been linked to adverse health outcomes. Gasoline- and diesel-powered engines and biomass burning are known to emit HNCO and hypothesized to emit precursors such as amides that can photochemically react to produce HNCO in the atmosphere. Increasingly, diesel engines in developed countries like the United States are required to use selective catalytic reduction (SCR) systems to reduce tailpipe emissions of oxides of nitrogen. SCR chemistry is known to produce HNCO as an intermediate product, and SCR systems have been implicated as an atmospheric source of HNCO. In this work, we measure HNCO emissions from an SCR system-equipped diesel engine and, in combination with earlier data, use a three-dimensional chemical transport model (CTM) to simulate the ambient concentrations and source/pathway contributions to HNCO in an urban environment. Engine tests were conducted at three different engine loads, using two different fuels and at multiple operating points. HNCO was measured using an acetate chemical ionization mass spectrometer. The diesel engine was found to emit primary HNCO (3-90 mg kg fuel-1) but we did not find any evidence that the SCR system or other aftertreatment devices (i.e., oxidation catalyst and particle filter) produced or enhanced HNCO emissions. The CTM predictions compared well with the only available observational datasets for HNCO in urban areas but underpredicted the contribution from secondary processes. The comparison implied that diesel-powered engines were the largest source of HNCO in urban areas. The CTM also predicted that daily-averaged concentrations of HNCO reached a maximum of ˜ 110 pptv but were an order of magnitude lower than the 1 ppbv level that could be associated with physiological effects in humans. Precursor contributions from other combustion sources (gasoline and biomass burning) and wintertime conditions could enhance HNCO concentrations but need to be explored in future work.

Icequake Tremors During Glacier Calving (Invited)

NASA Astrophysics Data System (ADS)

Walter, F.; O'Neel, S.; Bassis, J. N.; Fricker, H. A.; Pfeffer, W. T.

2009-12-01

Calving poses the largest uncertainty in the prediction of sea-level rise in response to global climate changes. A physically-based calving law has yet to be successfully implemented into ice-sheet models in order to adequately describe the mass loss of tidewater glaciers and ice shelves. Observations from a variety of glacial environments are needed in order to develop a theoretical framework for glacier calving. To this end, several recent investigations on glacier calving have involved the recording of seismic waves. In this context, the study of icequakes has been of high value, as it allows for detecting and monitoring of calving activity. However, there are unanswered fundamental questions concerning source aspects of calving-related seismic activity, such as focal depths of icequakes preceding and accompanying calving events, failure mechanisms and the role of fracturing and crevasse formation upstream from the glacier terminus. Icequake sources associated with opening of surface crevasses are well understood. As glacier ice is often homogeneous these waveforms are relatively simple and can be modeled using the moment tensor representation of a seismic point source. Calving-related seismicity, on the other hand, is more complex, and occurs near the terminus of a glacier, which is often highly heterogeneous due to pervasive crevassing. The signals last up to several minutes or even hours and exhibit both low-frequency (1-3Hz) as well as high-frequency (10-20Hz) energy or tremor-like waveforms. These characteristics can be explained by finite source properties, such as connecting and migrating fractures and repeated slip across contact planes between two bodies of ice. In this presentation we discuss sources of calving-related seismicity by comparing seismic calving records from several different glacial settings. We consider icequakes recorded during tidewater calving at Columbia Glacier, Alaska, during lake calving on Gornergletscher, Switzerland, and during ice shelf calving in Antarctica. The similarities and differences in seismic signatures of these different calving settings provide valuable insights and will be helpful in the theoretical treatment of glacier calving.

A NEW METHOD FOR FINDING POINT SOURCES IN HIGH-ENERGY NEUTRINO DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fang, Ke; Miller, M. Coleman

The IceCube collaboration has reported the first detection of high-energy astrophysical neutrinos, including ∼50 high-energy starting events, but no individual sources have been identified. It is therefore important to develop the most sensitive and efficient possible algorithms to identify the point sources of these neutrinos. The most popular current method works by exploring a dense grid of possible directions to individual sources, and identifying the single direction with the maximum probability of having produced multiple detected neutrinos. This method has numerous strengths, but it is computationally intensive and because it focuses on the single best location for a point source,more » additional point sources are not included in the evidence. We propose a new maximum likelihood method that uses the angular separations between all pairs of neutrinos in the data. Unlike existing autocorrelation methods for this type of analysis, which also use angular separations between neutrino pairs, our method incorporates information about the point-spread function and can identify individual point sources. We find that if the angular resolution is a few degrees or better, then this approach reduces both false positive and false negative errors compared to the current method, and is also more computationally efficient up to, potentially, hundreds of thousands of detected neutrinos.« less

Effects of pointing compared with naming and observing during encoding on item and source memory in young and older adults.

PubMed

Ouwehand, Kim; van Gog, Tamara; Paas, Fred

2016-10-01

Research showed that source memory functioning declines with ageing. Evidence suggests that encoding visual stimuli with manual pointing in addition to visual observation can have a positive effect on spatial memory compared with visual observation only. The present study investigated whether pointing at picture locations during encoding would lead to better spatial source memory than naming (Experiment 1) and visual observation only (Experiment 2) in young and older adults. Experiment 3 investigated whether response modality during the test phase would influence spatial source memory performance. Experiments 1 and 2 supported the hypothesis that pointing during encoding led to better source memory for picture locations than naming or observation only. Young adults outperformed older adults on the source memory but not the item memory task in both Experiments 1 and 2. In Experiments 1 and 2, participants manually responded in the test phase. Experiment 3 showed that if participants had to verbally respond in the test phase, the positive effect of pointing compared with naming during encoding disappeared. The results suggest that pointing at picture locations during encoding can enhance spatial source memory in both young and older adults, but only if the response modality is congruent in the test phase.

Processing Uav and LIDAR Point Clouds in Grass GIS

NASA Astrophysics Data System (ADS)

Petras, V.; Petrasova, A.; Jeziorska, J.; Mitasova, H.

2016-06-01

Today's methods of acquiring Earth surface data, namely lidar and unmanned aerial vehicle (UAV) imagery, non-selectively collect or generate large amounts of points. Point clouds from different sources vary in their properties such as number of returns, density, or quality. We present a set of tools with applications for different types of points clouds obtained by a lidar scanner, structure from motion technique (SfM), and a low-cost 3D scanner. To take advantage of the vertical structure of multiple return lidar point clouds, we demonstrate tools to process them using 3D raster techniques which allow, for example, the development of custom vegetation classification methods. Dense point clouds obtained from UAV imagery, often containing redundant points, can be decimated using various techniques before further processing. We implemented and compared several decimation techniques in regard to their performance and the final digital surface model (DSM). Finally, we will describe the processing of a point cloud from a low-cost 3D scanner, namely Microsoft Kinect, and its application for interaction with physical models. All the presented tools are open source and integrated in GRASS GIS, a multi-purpose open source GIS with remote sensing capabilities. The tools integrate with other open source projects, specifically Point Data Abstraction Library (PDAL), Point Cloud Library (PCL), and OpenKinect libfreenect2 library to benefit from the open source point cloud ecosystem. The implementation in GRASS GIS ensures long term maintenance and reproducibility by the scientific community but also by the original authors themselves.

An ounce of prevention. Is family planning disappearing from the healthcare picture?

PubMed

Hirshbein, N

1992-04-01

Despite family planning's enormous health and social benefits, US support for family planning is dwindling. Not only does family planning improve the health quality of life of children and their parents, it is also a cost-effective measure, saving an average of $4.40 in health and social services costs for each public dollar invested in the program. But over the past few years, political and financial neglect have brought the public family planning infrastructure near collapse. Combined federal and state spending on family planning amounts to less than 1% of public health care funds. In 1990, Medicaid represented the largest source of funds for family planning. But since Medicaid is tied to welfare eligibility, a woman must already have a child in order to qualify for Medicaid and its family planning benefits. Direct state funding for family planning services was the 2nd largest source. Several states, however, provided no funding whatsoever for family planning. The 3rd largest source was the Title X program, a federal program devoted exclusively to family planning. It provides services to some 4 million teens and low-income women nationwide. Over the past decade, Title X has received no significant increase in funding, and inflation has reduced its purchasing power by 2/3. As a result, Title X serves less women. Meanwhile, the number of unintended pregnancies continues to increase. The US already has the highest rate of unintended pregnancies in the developed world. This is partly a result of society's ambivalence towards sex, which makes it difficult to discuss -- much less promote -- family planning. Lack of support for family planning can also be traced to the vigorous efforts of the anti-birth control lobby, which has successfully defeated attempts to increase funding.

Earth observation taken by the Expedition 28 crew

NASA Image and Video Library

2011-09-06

ISS028-E-037979 (6 Sept. 2011) --- The Texas wild fires that have destroyed and continue to destroy thousands of acres of timber and prairie land, as well as hundreds of residences, are visible basically over many of the dozens of affected points across the nation's second largest state. The Expedition 28 crew members on the International Space Station, flying approximately 220 miles above Earth, recorded this wide panoramic image of Texas and beyond, from a point over the Gulf of Mexico, at 16:18:12 GMT, Sept. 6, 2011.

Earth observation taken by the Expedition 28 crew

NASA Image and Video Library

2011-09-06

ISS028-E-037977 (6 Sept. 2011) --- The Texas wild fires that have destroyed and continue to destroy thousands of acres of timber and prairie land, as well as hundreds of residences, are visible basically over many of the dozens of affected points across the nation's second largest state. The Expedition 28 crew members on the International Space Station, flying approximately 220 miles above Earth, recorded this wide panoramic image of Texas and beyond, from a point over the Gulf of Mexico, at 16:11:22 GMT, Sept. 6, 2011.

Mercury Contributions from Flint Creek and other Tributaries to the Upper Clark Fork River in Northwestern Montana

NASA Astrophysics Data System (ADS)

Langner, H.; Young, M.; Staats, M. F.

2013-12-01

Methylmercury contamination in biota is a major factor diminishing the environmental quality of the Upper Clark Fork River (CFR), e.g. by triggering human consumption limits of fish. The CFR is subject to one of the largest Superfund cleanup projects in the US, but remediation and restoration is currently focused exclusively on other mining-related contaminants (As, Cu, Zn, Pb, Cd), which may be counterproductive with respect to the bio-availability of mercury, for example by creation of wetlands along mercury-contaminated reaches of the river. The identification and elimination of Hg sources is an essential step toward reducing the methylmercury exposure in the biota of the CFR watershed because a strong correlation exists between total mercury levels in river sediment and methylmercury levels in aquatic life. We analyzed duplicate samples from the top sediment layer of the main stem and significant tributaries to the Clark Fork River along a 240 km reach between Butte, MT and downstream of the Missoula Valley. Mercury concentrations were 1.3 × 1.6 (mean × SD, n = 35) in the main stem. Concentrations in tributaries varied widely (0.02 to 85 mg/kg) and seemed only loosely related to the number of historic precious metal mines in the watershed. In the upper reach of the CFR, elevated Hg levels are likely caused by residual contaminated sediments in the flood plain. Levels tend to decrease downstream until Drummond, MT, where Flint Creek contributes a significant amount of mercury, causing Hg levels in the main stem CFR to increase from 0.7 to 4 mg/kg. Levels continue to decrease downstream. Flint Creek is the single largest contributor of Hg to the CFR. Detailed sampling of the main stem Flint Creek and tributaries (26 sites) showed extremely high levels in two tributaries (22 to 85 mg/kg) where historic milling operations were located. Elimination of these point sources may be accomplished comparatively economically and may significantly reduce mercury levels in Flint Creek and the Clark Fork River basin.

Incentive Analysis for Clean Water Act Reauthorization: Point Source/Nonpoint Source Trading for Nutrient Discharge Reductions (1992)

EPA Pesticide Factsheets

Paper focuses on trading schemes in which regulated point sources are allowed to avoid upgrading their pollution control technology to meet water quality-based effluent limits if they pay for equivalent (or greater) reductions in nonpoint source pollution.

Microbial Source Module (MSM): Documenting the Science and Software for Discovery, Evaluation, and Integration

EPA Science Inventory

The Microbial Source Module (MSM) estimates microbial loading rates to land surfaces from non-point sources, and to streams from point sources for each subwatershed within a watershed. A subwatershed, the smallest modeling unit, represents the common basis for information consume...

Testing and Refining the Direct and Inferential Mediation Model of Reading Comprehension

ERIC Educational Resources Information Center

Cromley, Jennifer G.; Azevedo, Roger

2007-01-01

A significant proportion of American high school students struggle with reading comprehension. Theoretical models of reading comprehension might help researchers understand these difficulties, because they can point to variables that make the largest contributions to comprehension. On the basis of an extensive review of the literature, we created…

Bedding down the Embedding: IL Reality in a Teacher Education Program

ERIC Educational Resources Information Center

Hobbs, Helen; Aspland, Tania

2003-01-01

Queensland University of Technology (QUT) is one of Australia's largest universities, enrolling 30 000 students. Our Information Literacy Framework and Syllabus was endorsed as university policy in February 2001. QUT Library uses the Australian Information Literacy Standards as the basis and entry point for our syllabus. The university-wide…

76 FR 61106 - Notice of Intent To Prepare an Environmental Impact Statement

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-03

... Environmental Protection, Office of Research Facilities, NIH, B13/2S11, 9000 Rockville Pike, Bethesda, Maryland... Institutes of Health (NIH), one of the world's largest biomedical research facilities and the Federal government's focal point for medical and behavioral research. The NIH Animal Center at Poolesville is a major...

29 CFR 1910.213 - Woodworking machinery requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... as to be free from sensible vibration when the largest size tool is mounted and run idle at full... lugs cast on the frame or with an equivalent means to limit the size of the saw blade that can be... in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal...

29 CFR 1910.213 - Woodworking machinery requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... as to be free from sensible vibration when the largest size tool is mounted and run idle at full... lugs cast on the frame or with an equivalent means to limit the size of the saw blade that can be... in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal...

29 CFR 1910.213 - Woodworking machinery requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... as to be free from sensible vibration when the largest size tool is mounted and run idle at full... lugs cast on the frame or with an equivalent means to limit the size of the saw blade that can be... in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal...

29 CFR 1910.213 - Woodworking machinery requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... as to be free from sensible vibration when the largest size tool is mounted and run idle at full... lugs cast on the frame or with an equivalent means to limit the size of the saw blade that can be... in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal...

29 CFR 1910.213 - Woodworking machinery requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... as to be free from sensible vibration when the largest size tool is mounted and run idle at full... lugs cast on the frame or with an equivalent means to limit the size of the saw blade that can be... in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal...

High Energy Astronomy Observatory (HEAO)

NASA Image and Video Library

1980-01-01

Like the Crab Nebula, the Vela Supernova Remnant has a radio pulsar at its center. In this image taken by the High Energy Astronomy Observatory (HEAO)-2/Einstein Observatory, the pulsar appears as a point source surrounded by weak and diffused emissions of x-rays. HEAO-2's computer processing system was able to record and display the total number of x-ray photons (a tiny bundle of radiant energy used as the fundamental unit of electromagnetic radiation) on a scale along the margin of the picture. The HEAO-2, the first imaging and largest x-ray telescope built to date, was capable of producing actual photographs of x-ray objects. Shortly after launch, the HEAO-2 was nicknamed the Einstein Observatory by its scientific experimenters in honor of the centernial of the birth of Albert Einstein, whose concepts of relativity and gravitation have influenced much of modern astrophysics, particularly x-ray astronomy. The HEAO-2, designed and developed by TRW, Inc. under the project management of the Marshall Space Flight Center, was launched aboard an Atlas/Centaur launch vehicle on November 13, 1978.

[Nursing knowledge production in Argentina, Chile, Paraguay and Uruguay].

PubMed

Lange, C; Meincke, S M; Schwartz, E

2001-07-01

Research is being pointed out as a path to nursing recognition. The knowledge production concerning the tendencies of research lines in nursing during the 90's, in Argentina, Chile, Paraguay and Uruguay, took part of a study that had the purpose to know the impact of the nursing profession practice on health in Latin America and in the Caribbean Islands. The methodology used was the exploratory quantitative research, and the database used were Lilacs and Medline. The most frequent investigation themes refer to nursing profession (up to 13.2%). Regarding the lines of investigation in nursing, we found out that the nursing professional stood out with 41%, being technique and methodology the main approaches. Chile was the country that produced the largest amount of research, 86.8% of the summaries. Referring to the financing source, no reference is made in 86.8% of the summaries. With reference to the number of authors involved with the published literature, 50.7% of the literature have only one author. The nurses should be aware to invest in the enlargement of this production.

Two-stage Framework for a Topology-Based Projection and Visualization of Classified Document Collections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oesterling, Patrick; Scheuermann, Gerik; Teresniak, Sven

During the last decades, electronic textual information has become the world's largest and most important information source available. People have added a variety of daily newspapers, books, scientific and governmental publications, blogs and private messages to this wellspring of endless information and knowledge. Since neither the existing nor the new information can be read in its entirety, computers are used to extract and visualize meaningful or interesting topics and documents from this huge information clutter. In this paper, we extend, improve and combine existing individual approaches into an overall framework that supports topological analysis of high dimensional document point cloudsmore » given by the well-known tf-idf document-term weighting method. We show that traditional distance-based approaches fail in very high dimensional spaces, and we describe an improved two-stage method for topology-based projections from the original high dimensional information space to both two dimensional (2-D) and three dimensional (3-D) visualizations. To show the accuracy and usability of this framework, we compare it to methods introduced recently and apply it to complex document and patent collections.« less

Stoichiometric determination of nitrate fate in agricultural ecosystems during rainfall events.

PubMed

Xu, Zuxin; Wang, Yiyao; Li, Huaizheng

2015-01-01

Ecologists have found a close relationship between the concentrations of nitrate (NO3-) and dissolved organic carbon (DOC) in ecosystems. However, it is difficult to determine the NO3- fate exactly because of the low coefficient in the constructed relationship. In the present paper, a negative power-function equation (r(2) = 0.87) was developed by using 411 NO3- data points and DOC:NO3- ratios from several agricultural ecosystems during different rainfall events. Our analysis of the stoichiometric method reveals several observations. First, the NO3- concentration demonstrated the largest changes when the DOC:NO3- ratio increased from 1 to 10. Second, the biodegradability of DOC was an important factor in controlling the NO3- concentration of agricultural ecosystems. Third, sediment was important not only as a denitrification site, but also as a major source of DOC for the overlying water. Fourth, a high DOC concentration was able to maintain a low NO3- concentration in the groundwater. In conclusion, this new stoichiometric method can be used for the accurate estimation and analysis of NO3- concentrations in ecosystems.

Reconnaissance samplings and characterization of aquatic humic substances at the Yuma Desalting Test Facility, Arizona

USGS Publications Warehouse

Malcolm, R.L.; Wershaw, R. L.; Thurman, E.M.; Aiken, G.R.; Pinckney, D.J.; Kaakinen, J.

1981-01-01

Smectite clay minerals were found to be the principal compound on the surface of the cellulose-acetate, reverse-osmosis membranes at the Yuma Desalting Test Facility. These clay minerals were not present in the pumped ground water, but were blown into the conveyance canal from adjacent soils. Humic substances from the water and suspended sediments were associated with the clay films on the membrane, but no definitive results concerning their role in fouling were achieved. Microbial fouling is believed to be only a minor aspect of membrane fouling. Chemical and physical changes in humic substances were extensively studied at four points in the water-treatment process. Humic substances accounted for the largest component (over 25 percent) of organic constituents. Humic substances in the canal source water were similar to other aquatic humic substances present in natural waters. During the treatment process, these substances are brominated and decolorized. The effect of these halogenated humic substances on membrane fouling is unclear, but their presence in the reverse-osmosis product water and reverse-osmosis reject brine, along with volatile trihalomethanes, has led to environmental concerns. (USGS)

Enhancing the sustainability and climate resiliency of health care facilities: a comparison of initiatives and toolkits.

PubMed

Balbus, John; Berry, Peter; Brettle, Meagan; Jagnarine-Azan, Shalini; Soares, Agnes; Ugarte, Ciro; Varangu, Linda; Prats, Elena Villalobos

2016-09-01

Extreme weather events have revealed the vulnerability of health care facilities and the extent of devastation to the community when they fail. With climate change anticipated to increase extreme weather and its impacts worldwide-severe droughts, floods, heat waves, and related vector-borne diseases-health care officials need to understand and address the vulnerabilities of their health care systems and take action to improve resiliency in ways that also meet sustainability goals. Generally, the health sector is among a country's largest consumers of energy and a significant source of greenhouse gas emissions. Now it has the opportunity lead climate mitigation, while reducing energy, water, and other costs. This Special Report summarizes several initiatives and compares three toolkits for implementing sustainability and resiliency measures for health care facilities: the Canadian Health Care Facility Climate Change Resiliency Toolkit, the U.S. Sustainable and Climate Resilient Health Care Facilities Toolkit, and the PAHO SMART Hospitals Toolkit of the World Health Organization/Pan American Health Organization. These tools and the lessons learned can provide a critical starting point for any health system in the Americas.

Social support relationships for sexual minority women in Mumbai, India: a photo elicitation interview study.

PubMed

Bowling, Jessamyn; Dodge, Brian; Banik, Swagata; Bartelt, Elizabeth; Mengle, Shruta; Guerra-Reyes, Lucia; Hensel, Devon; Herbenick, Debby; Anand, Vivek

2018-02-01

Little research exists on women who do not identify as heterosexual in India. Social support for sexual minority women may protect against the effects of discrimination. An examination of significant social relationships may point to both strengths and weaknesses in this support. We aimed to understand relationship prioritisation and communication patterns associated with the social support of sexual minority women in Mumbai. In partnership with the Humsafar Trust, India's oldest and largest sexual and gender minority-advocacy organisation, we conducted photo-elicitation interviews with 18 sexual minority women, using participants' photographs to prompt dialogue about their social support. Intimate partners were a source of dependable support and many of those without relationships were seeking them. Participants' extended networks included friends and family as well as less formal relationships of social support. Participants mediated their communication with particular social network members, which involved filtering information sexual identity, romantic interests, and personal aspirations, among others. The diverse relationships that sexual minority women have in their social support networks may be used to guide programmes to improve health outcomes.

Hydrogen Bearing Material in the Lunar Exosphere

NASA Astrophysics Data System (ADS)

Hurley, D.; Benna, M.; Colaprete, A.; Retherford, K. D.; Cook, J. C.; Elphic, R. C.; Farrell, W. M.; Killen, R. M.; Sarantos, M.

2015-12-01

We report on observations of water and its daughters in the lunar exosphere. Data from LADEE NMS, LADEE UVS, and LRO LAMP indicating the presence of H, H2, OH, and H2O are presented in terms of their relationship to external drivers. These observations point to the roles of solar wind and micrometeoroids in the source and release of hydrogen-bearing atoms and molecules in the exosphere. In particular, the implantation of H via solar wind is found to be the largest contributor to H2 in the moon's exosphere. However, the spatial distribution is more consistent with a release mechanism centered on the morning hemisphere. Thus the data are consistent with H2 created through a 2-step process involving the implantation of solar wind and subsequent release by micrometeoroids. This accounts for >12% of the solar wind H budget, leaving < 50% of the solar wind proton budget unobserved. LADEE data are consistent with water mainly being released by micrometeoroids. We present an overall picture of the present-day water cycle occurring on the Moon.

Mobile Apps for Self-Injury: A Content Analysis.

PubMed

Vieira, Aaron M; Lewis, Stephen P

2018-05-01

A growing body of research points to the salience of the Internet and mobile material among individuals who self-injure. However, to date, no research has investigated the mobile apps related to nonsuicidal self-injury (NSSI). Such information would clarify which apps may be useful for those who self-injure while highlighting whether app-related content warrants improvement. The current study examined the content and usability of NSSI apps available on the two largest app-related platforms (Google Play and iTunes). Using content analysis, apps were examined regarding their content (e.g., presence of NSSI myths and types of coping strategies) as well as usability (e.g., app performance). Results indicate that NSSI apps have varied content, with few developed by, or affiliated with, a trusted source (e.g., university). NSSI apps tend to not propagate NSSI myths that vary with respect to the quality of coping strategies offered. They also tend to be rated favorably in terms of their usability. Overall, the present findings add to the NSSI literature and highlight several implications and avenues for future work, which are discussed.

Image of the Vela Supernova Remnant Taken by the High Energy Astronomy Observatory (HEAO)-2

NASA Technical Reports Server (NTRS)

1980-01-01

Like the Crab Nebula, the Vela Supernova Remnant has a radio pulsar at its center. In this image taken by the High Energy Astronomy Observatory (HEAO)-2/Einstein Observatory, the pulsar appears as a point source surrounded by weak and diffused emissions of x-rays. HEAO-2's computer processing system was able to record and display the total number of x-ray photons (a tiny bundle of radiant energy used as the fundamental unit of electromagnetic radiation) on a scale along the margin of the picture. The HEAO-2, the first imaging and largest x-ray telescope built to date, was capable of producing actual photographs of x-ray objects. Shortly after launch, the HEAO-2 was nicknamed the Einstein Observatory by its scientific experimenters in honor of the centernial of the birth of Albert Einstein, whose concepts of relativity and gravitation have influenced much of modern astrophysics, particularly x-ray astronomy. The HEAO-2, designed and developed by TRW, Inc. under the project management of the Marshall Space Flight Center, was launched aboard an Atlas/Centaur launch vehicle on November 13, 1978.

Strategies for single-point diamond machining a large format germanium blazed immersion grating

NASA Astrophysics Data System (ADS)

Montesanti, R. C.; Little, S. L.; Kuzmenko, P. J.; Bixler, J. V.; Jackson, J. L.; Lown, J. G.; Priest, R. E.; Yoxall, B. E.

2016-07-01

A large format germanium immersion grating was flycut with a single-point diamond tool on the Precision Engineering Research Lathe (PERL) at the Lawrence Livermore National Laboratory (LLNL) in November - December 2015. The grating, referred to as 002u, has an area of 59 mm x 67 mm (along-groove and cross-groove directions), line pitch of 88 line/mm, and blaze angle of 32 degree. Based on total groove length, the 002u grating is five times larger than the previous largest grating (ZnSe) cut on PERL, and forty-five times larger than the previous largest germanium grating cut on PERL. The key risks associated with cutting the 002u grating were tool wear and keeping the PERL machine running uninterrupted in a stable machining environment. This paper presents the strategies employed to mitigate these risks, introduces pre-machining of the as-etched grating substrate to produce a smooth, flat, damage-free surface into which the grooves are cut, and reports on trade-offs that drove decisions and experimental results.

40 CFR 414.90 - Applicability; description of the subcategory of direct discharge point sources that use end-of...

Code of Federal Regulations, 2010 CFR

2010-07-01

... ORGANIC CHEMICALS, PLASTICS, AND SYNTHETIC FIBERS Direct Discharge Point Sources That Use End-of-Pipe... subcategory of direct discharge point sources that use end-of-pipe biological treatment. 414.90 Section 414.90... that use end-of-pipe biological treatment. The provisions of this subpart are applicable to the process...

40 CFR Table 4 to Part 455 - BAT and NSPS Effluent Limitations for Priority Pollutants for Direct Discharge Point Sources That...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false BAT and NSPS Effluent Limitations for Priority Pollutants for Direct Discharge Point Sources That use End-of-Pipe Biological Treatment 4 Table 4... Limitations for Priority Pollutants for Direct Discharge Point Sources That use End-of-Pipe Biological...

Multi-rate, real time image compression for images dominated by point sources

NASA Technical Reports Server (NTRS)

Huber, A. Kris; Budge, Scott E.; Harris, Richard W.

1993-01-01

An image compression system recently developed for compression of digital images dominated by point sources is presented. Encoding consists of minimum-mean removal, vector quantization, adaptive threshold truncation, and modified Huffman encoding. Simulations are presented showing that the peaks corresponding to point sources can be transmitted losslessly for low signal-to-noise ratios (SNR) and high point source densities while maintaining a reduced output bit rate. Encoding and decoding hardware has been built and tested which processes 552,960 12-bit pixels per second at compression rates of 10:1 and 4:1. Simulation results are presented for the 10:1 case only.

Fingerprinting two metal contaminants in streams with Cu isotopes near the Dexing Mine, China.

PubMed

Song, Shiming; Mathur, Ryan; Ruiz, Joaquin; Chen, Dandan; Allin, Nicholas; Guo, Kunyi; Kang, Wenkai

2016-02-15

Transition metal isotope signatures are becoming useful for fingerprinting sources in surface waters. This study explored the use of Cu isotope values to trace dissolved metal contaminants in stream water throughout a watershed affected by mining by-products of the Dexing Mine, the largest porphyry Cu operation in Asia. Cu isotope values of stream water were compared to potential mineral sources of Cu in the mining operation, and to proximity to the known Cu sources. The first mineral source, chalcopyrite, CuFeS2 has a 'tight' cluster of Cu isotope values (-0.15‰ to +1.65‰; +0.37 ± 0.6‰, 1σ, n=10), and the second mineral source, pyrite (FeS2), has a much larger range of Cu isotope values (-4‰ to +11.9‰; 2.7 ± 4.3‰, 1σ, n=16). Dissolved Cu isotope values of stream water indicated metal derived from either chalcopyrite or pyrite. Above known Cu mineralization, stream waters are approximately +1.5‰ greater than the average chalcopyrite and are interpreted as derived from weathering of chalcopyrite. In contrast, dissolved Cu isotope values in stream water emanating from tailings piles had Cu isotope values similar to or greater than pyrite (>+6‰, a common mineral in the tailings). These values are interpreted as sourced from the tailings, even in solutions that possess significantly lower concentrations of Cu (<0.05 ppm). Elevated Cu isotope values were also found in two soil and two tailings samples (δ(65)Cu ranging between +2 to +5‰). These data point to the mineral pyrite in tailings as the mineral source for the elevated Cu isotope values. Therefore, Cu isotope values of waters emanating from a clearly contaminated drainage possess different Cu isotope values, permitting the discrimination of Cu derived from chalcopyrite and pyrite in solution. Data demonstrate the utility of Cu isotopic values in waters, minerals, and soils to fingerprint metallic contamination for environmental problems. Copyright © 2015 Elsevier B.V. All rights reserved.

[Spatial heterogeneity and classified control of agricultural non-point source pollution in Huaihe River Basin].

PubMed

Zhou, Liang; Xu, Jian-Gang; Sun, Dong-Qi; Ni, Tian-Hua

2013-02-01

Agricultural non-point source pollution is of importance in river deterioration. Thus identifying and concentrated controlling the key source-areas are the most effective approaches for non-point source pollution control. This study adopts inventory method to analysis four kinds of pollution sources and their emissions intensity of the chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in 173 counties (cities, districts) in Huaihe River Basin. The four pollution sources include livestock breeding, rural life, farmland cultivation, aquacultures. The paper mainly addresses identification of non-point polluted sensitivity areas, key pollution sources and its spatial distribution characteristics through cluster, sensitivity evaluation and spatial analysis. A geographic information system (GIS) and SPSS were used to carry out this study. The results show that: the COD, TN and TP emissions of agricultural non-point sources were 206.74 x 10(4) t, 66.49 x 10(4) t, 8.74 x 10(4) t separately in Huaihe River Basin in 2009; the emission intensity were 7.69, 2.47, 0.32 t.hm-2; the proportions of COD, TN, TP emissions were 73%, 24%, 3%. The paper achieves that: the major pollution source of COD, TN and TP was livestock breeding and rural life; the sensitivity areas and priority pollution control areas among the river basin of non-point source pollution are some sub-basins of the upper branches in Huaihe River, such as Shahe River, Yinghe River, Beiru River, Jialu River and Qingyi River; livestock breeding is the key pollution source in the priority pollution control areas. Finally, the paper concludes that pollution type of rural life has the highest pollution contribution rate, while comprehensive pollution is one type which is hard to control.

A method to analyze "source-sink" structure of non-point source pollution based on remote sensing technology.

PubMed

Jiang, Mengzhen; Chen, Haiying; Chen, Qinghui

2013-11-01

With the purpose of providing scientific basis for environmental planning about non-point source pollution prevention and control, and improving the pollution regulating efficiency, this paper established the Grid Landscape Contrast Index based on Location-weighted Landscape Contrast Index according to the "source-sink" theory. The spatial distribution of non-point source pollution caused by Jiulongjiang Estuary could be worked out by utilizing high resolution remote sensing images. The results showed that, the area of "source" of nitrogen and phosphorus in Jiulongjiang Estuary was 534.42 km(2) in 2008, and the "sink" was 172.06 km(2). The "source" of non-point source pollution was distributed mainly over Xiamen island, most of Haicang, east of Jiaomei and river bank of Gangwei and Shima; and the "sink" was distributed over southwest of Xiamen island and west of Shima. Generally speaking, the intensity of "source" gets weaker along with the distance from the seas boundary increase, while "sink" gets stronger. Copyright © 2013 Elsevier Ltd. All rights reserved.

Initiation process of the Mw 6.2 central Tottori, Japan, earthquake on October 21, 2016: Stress transfer due to its largest foreshock of Mw 4.1

NASA Astrophysics Data System (ADS)

Noda, S.; Ellsworth, W. L.

2017-12-01

On October 21, 2016, a strike-slip earthquake with Mw 6.2 occurred in the central Tottori prefecture, Japan. It was preceded by a foreshock sequence that began with a Mw 4.1 event, the largest earthquake for the sequence, and lasted about two hours. According to the JMA catalog, the largest foreshock had a similar focal mechanism as the mainshock and was located in the immediate vicinity of the mainshock hypocenter. The goal of this study is to understand the relationship between the foreshock and the initial rupture of the mainshock. We first determine the relative hypocenter distance between the foreshock and mainshock using the P-wave onsets on Hi-net station records. The initiation points of the two events are likely about 100 m apart according to the current results, but could be closer. Within the location uncertainty, they might either be coplanar or on subparallel planes. Next, we obtain the slip-history models from a kinematic inversion method using empirical Green's functions derived from other foreshocks with M 2.2 - 2.4. The Mw 4.1 foreshock and Mw 6.2 mainshock started in a similar way until approximately 0.2 s after their onsets. For the foreshock, the rapid growth stage completed by 0.2 s even though the rupture propagation continued for 0.4 - 0.5 s longer (note that 0.2 s is significantly shorter than the typical source duration of a Mw 4.1 earthquake). On the other hand, the mainshock rupture continued to grow rapidly after 0.2 s. The comparison between the relative hypocenter locations and the slip models shows that the mainshock nucleated within the area strongly effected by both static and dynamic stress changes created by the foreshock. We also find that the mainshock initially propagated away from the foreshock hypocenter. We consider that the stress transfer process is a key to understand the mainshock nucleation as well as its rupture growth process.

Discovering Tau and Muon Solar Neutrino Flares above Backgrounds

NASA Astrophysics Data System (ADS)

Fargion, D.; Moscato, F.

2005-01-01

Solar neutrino flares astronomy is at the edge of its discover. High energy flare particles (protons, alpha) whose self scattering within the solar corona is source of a rich prompt charged pions are also source of sharp solar neutrino "burst" (at tens-hundred MeV) produced by their pion-muon primary decay in flight. This brief (minute) solar neutrino "burst" at largest peak overcome by four-five order of magnitude the steady atmospheric neutrino noise at the Earth. Later on, solar flare particles hitting the terrestrial atmosphere may marginally increase the atmospheric neutrino flux without relevant consequences. Largest prompt "burst" solar neutrino flare may be detected in present or better in future largest neutrino underground neutrino detectors. Our estimate for the recent and exceptional October - November 2003 solar flares gives a number of events above or just near unity for Super-Kamiokande. The neutrino spectra may reflect in a subtle way the neutrino flavour mixing in flight. A surprising tau appearance may even occur for a hard ({E}_{nu}_{mu}--> {E}_{nu}_{tau} > 4 GeV) flare spectra. A comparison of the solar neutrino flare (at their birth place on Sun and after oscillation on the arrival on the Earth) with other neutrino foreground is here described and it offer an independent road map to disentangle the neutrino flavour puzzles and its secret flavour mixing angles .

Defense Suppliers: Factors Affecting U.S. Titanium Aircraft Component Manufacturers’ Market Share of DOD Business

DTIC Science & Technology

2013-07-01

countries” currently are exempt from the specialty metals domestic source restriction and are permitted to use non-domestic produced titanium to...industry is the largest consumer of titanium metals in the world. DOD estimates that the aerospace industry accounts for 60 to 75 percent of the U.S...DOD, the specialty metals domestic source restriction limits the U.S. prime contractors’ and aircraft component manufacturers’ purchase of titanium

Chinese research on shock physics. Studies in Chinese Science

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mao, N.H.

1992-07-01

Shock wave research encompasses many different disciplines. This monograph limits the scope to Chinese research on solids and is based on available open literature sources. For the purpose of this monograph, the papers are divided into seven groups, i.e. review and tutorial; equations of state; phase transitions; geological materials; modeling and simulations; experimental techniques; and mechanical properties. The largest group of papers is experimental techniques and numbers 22, or about 40% of the total sources.

Stellar-mass black holes and ultraluminous x-ray sources.

PubMed

Fender, Rob; Belloni, Tomaso

2012-08-03

We review the likely population, observational properties, and broad implications of stellar-mass black holes and ultraluminous x-ray sources. We focus on the clear empirical rules connecting accretion and outflow that have been established for stellar-mass black holes in binary systems in the past decade and a half. These patterns of behavior are probably the keys that will allow us to understand black hole feedback on the largest scales over cosmological time scales.

Presbyterian Healthcare Services: New Mexico's managed care leader.

PubMed

Matheny de Guzman, M

1998-01-01

In 1997, PHS enhanced its presence in the managed care market by adding a large HMO to its health plan and snagging the largest part of state Medicaid managed care contracts. The health plan, once the source of only 15% of the system's revenue, is fast becoming the dominate component of the healthcare delivery system--a source of discontent for those who liked the old system. Find out the strategy behind these changes and plans for the future.

Who Will Teach? Experience Matters

ERIC Educational Resources Information Center

National Commission on Teaching and America's Future, 2010

2010-01-01

Working with Richard Ingersoll, professor of Education and Sociology at the University of Pennsylvania, the National Commission on Teaching and America's Future (NCTAF) examined and analyzed data from the "Schools and Staffing Survey" (SASS), the largest and most comprehensive source of data on teachers, gathered from a nationally…

ALMA Observing Strategies

NASA Astrophysics Data System (ADS)

Biggs, Andy

2018-03-01

The ALMA Observing Tool (OT) is a Java-based tool used to prepare ALMA observations. In this talk, I highlight the particular features relevant to setting up single dish observations when these are needed to observe sources where the largest angular scale requires the addition of the total power antennas.

Energy monitoring in gins

USDA-ARS?s Scientific Manuscript database

Energy costs are the second largest source of variable costs for cotton gins, accounting for 27% of variable costs. Energy use has typically not been a major consideration in gin design, and previous studies of energy use have utilized instantaneous readings or aggregated season-long values. In this...

Energy Monitoring in Gins - 2013 Update

USDA-ARS?s Scientific Manuscript database

Energy, comprised of electricity and fuel, is the second largest source of variable costs for cotton gins, after labor. Few studies of gin energy use have been conducted recently and none have monitored energy use continuously throughout the ginning season. More detailed information is needed to ide...

Energy Monitoring in Gins - 2012 Preliminary Results

USDA-ARS?s Scientific Manuscript database

Electricity and fuel are the second largest source of variable costs for cotton gins, after labor. Few studies of gin energy use have been conducted recently and none have monitored energy use continuously throughout the ginning season. More detailed information is needed to identify management st...

Energy Monitoring in Gins - 2011

USDA-ARS?s Scientific Manuscript database

Energy costs are the second largest source of variable costs for gins, accounting for 27% of variable costs. Energy use has typically not been a major consideration in gin design and previous studies of energy use have utilized instantaneous readings or aggregated season-long values. Electricity u...

Electricity use patterns in cotton gins

USDA-ARS?s Scientific Manuscript database

Energy costs are the second largest source of variable costs for cotton gins, with electricity accounting for 18% of variable costs. Energy use has typically not been a major consideration in gin design and previous studies of energy use have utilized instantaneous readings or aggregated season-lon...

Environmental Issues Related to Conventional Hydropower

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Zhiqun; Colotelo, Alison HA; Brown, Richard S.

Hydropower is the largest renewable electrical energy source in the world and has a total global capacity of approximately 1,010 GW from 150 countries. Although hydropower has many environmental advantages, hydropower dams have potential adverse ecological impacts such as fish passage, water quality, and habitat alterations.

Mass balance evaluation of alcohol emission from cattle feed

USDA-ARS?s Scientific Manuscript database

Silage on dairy farms has been recognized as an important source of volatile organic compounds (VOCs) to the atmosphere, and therefore a contributor to tropospheric ozone. Considering reactivity and likely emission rates, ethanol, 1-propanol, and acetaldehyde probably make the largest contribution t...

75 FR 71643 - Periodic Reporting Rules

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-24

... on one-time studies. 2. Mail processing is the largest source of volume-variable costs in the postal... a strategic rulemaking, identifies several potential areas for study, and seeks suggestions for... data collection programs that need to be established. It might list existing analytical studies that...

SEDIMENT ANALYSIS - LANDSCAPE INDICATORS FOR PESTICIDES STUDY FOR MID-ATLANTIC COASTAL STREAMS (LIPS-MACS)

EPA Science Inventory

Nonpoint-source pollution, including pesticides and toxics, is the largest threat facing aquatic resources today. Understanding how pesticides applied to agricultural fields and suburban lawns reach and influence stream water quality is the focus of the Landscape Indicators for ...

The future of aquaculture

USDA-ARS?s Scientific Manuscript database

Fish is now the largest source of animal protein in the world, with aquaculture contributing more than half the world’s seafood supply. The world needs to produce significantly more fish in the future to meet the demands of a growing and increasingly affluent global population. Capture fisheries ar...

The FY2011 Federal Budget

DTIC Science & Technology

2010-08-04

long been the largest source of federal revenues, followed by social insurance (payroll) taxes. Federal individual and corporate income tax revenues...915 billion (6.4% of GDP). Corporate income tax revenues fell from $304 billion in FY2008 to $138 billion in FY2009. Federal revenues from other

Significant human impact on the flux and δ(34)S of sulfate from the largest river in North America.

PubMed

Killingsworth, Bryan A; Bao, Huiming

2015-04-21

Riverine dissolved sulfate (SO4(2-)) flux and sulfur stable isotope composition (δ(34)S) yield information on the sources and processes affecting sulfur cycling on different spatial and temporal scales. However, because pristine preindustrial natural baselines of riverine SO4(2-) flux and δ(34)S cannot be directly measured, anthropogenic impact remains largely unconstrained. Here we quantify natural and anthropogenic SO4(2-) flux and δ(34)S for North America's largest river, the Mississippi, by means of an exhaustive source compilation and multiyear monitoring. Our data and analysis show that, since before industrialization to the present, Mississippi River SO4(2-) has increased in flux from 7.0 to 27.8 Tg SO4(2-) yr(-1), and in mean δ(34)S from -5.0‰, within 95% confidence limits of -14.8‰ to 4.1‰ (assuming normal distribution for mixing model input parameters), to -2.7 ± 1.6‰, reflecting an impressive footprint of bedrocks particular to this river basin and human activities. Our first-order modern Mississippi River sulfate partition is 25 ± 6% natural and 75% ± 6% anthropogenic sources. Furthermore, anthropogenic coal usage is implicated as the dominant source of modern Mississippi River sulfate, with an estimated 47 ± 5% and 13% of total Mississippi River sulfate due to coal mining and burning, respectively.

Very Large Area/Volume Microwave ECR Plasma and Ion Source

NASA Technical Reports Server (NTRS)

Foster, John E. (Inventor); Patterson, Michael J. (Inventor)

2009-01-01

The present invention is an apparatus and method for producing very large area and large volume plasmas. The invention utilizes electron cyclotron resonances in conjunction with permanent magnets to produce dense, uniform plasmas for long life ion thruster applications or for plasma processing applications such as etching, deposition, ion milling and ion implantation. The large area source is at least five times larger than the 12-inch wafers being processed to date. Its rectangular shape makes it easier to accommodate to materials processing than sources that are circular in shape. The source itself represents the largest ECR ion source built to date. It is electrodeless and does not utilize electromagnets to generate the ECR magnetic circuit, nor does it make use of windows.

Fermi-LAT observations of the gamma-ray burst GRB 130427A.

PubMed

Ackermann, M; Ajello, M; Asano, K; Atwood, W B; Axelsson, M; Baldini, L; Ballet, J; Barbiellini, G; Baring, M G; Bastieri, D; Bechtol, K; Bellazzini, R; Bissaldi, E; Bonamente, E; Bregeon, J; Brigida, M; Bruel, P; Buehler, R; Burgess, J Michael; Buson, S; Caliandro, G A; Cameron, R A; Caraveo, P A; Cecchi, C; Chaplin, V; Charles, E; Chekhtman, A; Cheung, C C; Chiang, J; Chiaro, G; Ciprini, S; Claus, R; Cleveland, W; Cohen-Tanugi, J; Collazzi, A; Cominsky, L R; Connaughton, V; Conrad, J; Cutini, S; D'Ammando, F; de Angelis, A; DeKlotz, M; de Palma, F; Dermer, C D; Desiante, R; Diekmann, A; Di Venere, L; Drell, P S; Drlica-Wagner, A; Favuzzi, C; Fegan, S J; Ferrara, E C; Finke, J; Fitzpatrick, G; Focke, W B; Franckowiak, A; Fukazawa, Y; Funk, S; Fusco, P; Gargano, F; Gehrels, N; Germani, S; Gibby, M; Giglietto, N; Giles, M; Giordano, F; Giroletti, M; Godfrey, G; Granot, J; Grenier, I A; Grove, J E; Gruber, D; Guiriec, S; Hadasch, D; Hanabata, Y; Harding, A K; Hayashida, M; Hays, E; Horan, D; Hughes, R E; Inoue, Y; Jogler, T; Jóhannesson, G; Johnson, W N; Kawano, T; Knödlseder, J; Kocevski, D; Kuss, M; Lande, J; Larsson, S; Latronico, L; Longo, F; Loparco, F; Lovellette, M N; Lubrano, P; Mayer, M; Mazziotta, M N; McEnery, J E; Michelson, P F; Mizuno, T; Moiseev, A A; Monzani, M E; Moretti, E; Morselli, A; Moskalenko, I V; Murgia, S; Nemmen, R; Nuss, E; Ohno, M; Ohsugi, T; Okumura, A; Omodei, N; Orienti, M; Paneque, D; Pelassa, V; Perkins, J S; Pesce-Rollins, M; Petrosian, V; Piron, F; Pivato, G; Porter, T A; Racusin, J L; Rainò, S; Rando, R; Razzano, M; Razzaque, S; Reimer, A; Reimer, O; Ritz, S; Roth, M; Ryde, F; Sartori, A; Parkinson, P M Saz; Scargle, J D; Schulz, A; Sgrò, C; Siskind, E J; Sonbas, E; Spandre, G; Spinelli, P; Tajima, H; Takahashi, H; Thayer, J G; Thayer, J B; Thompson, D J; Tibaldo, L; Tinivella, M; Torres, D F; Tosti, G; Troja, E; Usher, T L; Vandenbroucke, J; Vasileiou, V; Vianello, G; Vitale, V; Winer, B L; Wood, K S; Yamazaki, R; Younes, G; Yu, H-F; Zhu, S J; Bhat, P N; Briggs, M S; Byrne, D; Foley, S; Goldstein, A; Jenke, P; Kippen, R M; Kouveliotou, C; McBreen, S; Meegan, C; Paciesas, W S; Preece, R; Rau, A; Tierney, D; van der Horst, A J; von Kienlin, A; Wilson-Hodge, C; Xiong, S; Cusumano, G; La Parola, V; Cummings, J R

2014-01-03

The observations of the exceptionally bright gamma-ray burst (GRB) 130427A by the Large Area Telescope aboard the Fermi Gamma-ray Space Telescope provide constraints on the nature of these unique astrophysical sources. GRB 130427A had the largest fluence, highest-energy photon (95 GeV), longest γ-ray duration (20 hours), and one of the largest isotropic energy releases ever observed from a GRB. Temporal and spectral analyses of GRB 130427A challenge the widely accepted model that the nonthermal high-energy emission in the afterglow phase of GRBs is synchrotron emission radiated by electrons accelerated at an external shock.

Fermi-LAT Observations of the Gamma-Ray Burst GRB 130427A

DOE PAGES

Ackermann, M.; Ajello, M.; Asano, K.; ...

2013-11-21

The Large Area Telescope aboard the Fermi Gamma-ray Space Telescope provide constraints on the nature of these unique astrophysical sources using the observations of the exceptionally bright gamma-ray burst (GRB) 130427A. We found that GRB 130427A had the largest fluence, highest-energy photon (95 GeV), longest γ-ray duration (20 hours), and one of the largest isotropic energy releases ever observed from a GRB. Temporal and spectral analyses of GRB 130427A challenge the widely accepted model that the nonthermal high-energy emission in the afterglow phase of GRBs is synchrotron emission radiated by electrons accelerated at an external shock.

Fermi-LAT Observations of the Gamma-Ray Burst GRB 130427A

NASA Technical Reports Server (NTRS)

Ackermann, M.; Ajello, M.; Asano, K.; Atwood, W. B.; Axelsson, M.; Baldini, L.; Ballet, J.; Barbiellini, G.; Baring, M. G.; Bastieri, D.;

Photographer : JPL Range : 4.2 million kilometers (2.6 million miles) Ganymede is Jupiter's Largest

NASA Technical Reports Server (NTRS)

1979-01-01

Photographer : JPL Range : 4.2 million kilometers (2.6 million miles) Ganymede is Jupiter's Largest Galilean satellites and 3rd from the planet. Photo taken after midnight Ganymede is slightly larger than Mercury but much less dense (twice the density of water). Its surface brightness is 4 times of Earth's Moon. Mare regions (dark features) are like the Moon's but have twice the brightness, and believed to be unlikely of rock or lava as the Moon's are. It's north pole seems covered with brighter material and may be water frost. Scattered brighter spots may be related to impact craters or source of fresh ice.

A Comparative Analysis of Vibrio cholerae Contamination in Point-of-Drinking and Source Water in a Low-Income Urban Community, Bangladesh

PubMed Central

Ferdous, Jannatul; Sultana, Rebeca; Rashid, Ridwan B.; Tasnimuzzaman, Md.; Nordland, Andreas; Begum, Anowara; Jensen, Peter K. M.

2018-01-01

Bangladesh is a cholera endemic country with a population at high risk of cholera. Toxigenic and non-toxigenic Vibrio cholerae (V. cholerae) can cause cholera and cholera-like diarrheal illness and outbreaks. Drinking water is one of the primary routes of cholera transmission in Bangladesh. The aim of this study was to conduct a comparative assessment of the presence of V. cholerae between point-of-drinking water and source water, and to investigate the variability of virulence profile using molecular methods of a densely populated low-income settlement of Dhaka, Bangladesh. Water samples were collected and tested for V. cholerae from “point-of-drinking” and “source” in 477 study households in routine visits at 6 week intervals over a period of 14 months. We studied the virulence profiles of V. cholerae positive water samples using 22 different virulence gene markers present in toxigenic O1/O139 and non-O1/O139 V. cholerae using polymerase chain reaction (PCR). A total of 1,463 water samples were collected, with 1,082 samples from point-of-drinking water in 388 households and 381 samples from 66 water sources. V. cholerae was detected in 10% of point-of-drinking water samples and in 9% of source water samples. Twenty-three percent of households and 38% of the sources were positive for V. cholerae in at least one visit. Samples collected from point-of-drinking and linked sources in a 7 day interval showed significantly higher odds (P < 0.05) of V. cholerae presence in point-of-drinking compared to source [OR = 17.24 (95% CI = 7.14–42.89)] water. Based on the 7 day interval data, 53% (17/32) of source water samples were negative for V. cholerae while linked point-of-drinking water samples were positive. There were significantly higher odds (p < 0.05) of the presence of V. cholerae O1 [OR = 9.13 (95% CI = 2.85–29.26)] and V. cholerae O139 [OR = 4.73 (95% CI = 1.19–18.79)] in source water samples than in point-of-drinking water samples. Contamination of water at the point-of-drinking is less likely to depend on the contamination at the water source. Hygiene education interventions and programs should focus and emphasize on water at the point-of-drinking, including repeated cleaning of drinking vessels, which is of paramount importance in preventing cholera. PMID:29616005

Modeling of Pixelated Detector in SPECT Pinhole Reconstruction.

PubMed

Feng, Bing; Zeng, Gengsheng L

2014-04-10

A challenge for the pixelated detector is that the detector response of a gamma-ray photon varies with the incident angle and the incident location within a crystal. The normalization map obtained by measuring the flood of a point-source at a large distance can lead to artifacts in reconstructed images. In this work, we investigated a method of generating normalization maps by ray-tracing through the pixelated detector based on the imaging geometry and the photo-peak energy for the specific isotope. The normalization is defined for each pinhole as the normalized detector response for a point-source placed at the focal point of the pinhole. Ray-tracing is used to generate the ideal flood image for a point-source. Each crystal pitch area on the back of the detector is divided into 60 × 60 sub-pixels. Lines are obtained by connecting between a point-source and the centers of sub-pixels inside each crystal pitch area. For each line ray-tracing starts from the entrance point at the detector face and ends at the center of a sub-pixel on the back of the detector. Only the attenuation by NaI(Tl) crystals along each ray is assumed to contribute directly to the flood image. The attenuation by the silica (SiO 2 ) reflector is also included in the ray-tracing. To calculate the normalization for a pinhole, we need to calculate the ideal flood for a point-source at 360 mm distance (where the point-source was placed for the regular flood measurement) and the ideal flood image for the point-source at the pinhole focal point, together with the flood measurement at 360 mm distance. The normalizations are incorporated in the iterative OSEM reconstruction as a component of the projection matrix. Applications to single-pinhole and multi-pinhole imaging showed that this method greatly reduced the reconstruction artifacts.

Assessment of the "fish tumors or other deformities" beneficial use impairment in brown bullhead (Ameiurus nebulosus): I. Orocutaneous tumors

USGS Publications Warehouse

Blazer, V.S.; Rafferty, S.D.; Baumman, P.C.; Smith, S.B.; Obert, E.C.

2009-01-01

The "fish tumor or other deformities" beneficial use impairment (BUI) occurs at 9 of the 12 areas of concern (AOC) on Lake Erie. As point sources are mitigated and remediation occurs, AOC are faced with determining delisting criteria. The lack of standardized analyses for this BUI has confounded that process. For orocutaneous tumors, different criteria (presumptive tumors and/or abnormal barbels) and methodology (gross versus microscopic observations) have been used. Hence, this project evaluated tumors at numerous AOC and non-AOC sites and compared methodology. In 1998-2000 the prevalence of presumptive orocutaneous tumors and barbel abnormalities was compared in brown bullhead (Ameiurus nebulosus) collected at eight AOC. The Black (46.7%), Buffalo (29.3%), Cuyahoga (58.9%), and Detroit (26.5%) rivers and Presque Isle Bay (28.6%) had high prevalences of orocutaneous tumors, while the Niagara (10%), Maumee (3.9%) and Ashtabula (4.4%) rivers were lower. From 2002 to 2007 the prevalence of orocutaneous tumors at Presque Isle Bay was consistently near 30%. A variety of non-AOC sites, as potential reference sites, were also monitored during this time. By combining years and sites the prevalence of orocutaneous tumors in bullhead (age 2-12 years) at inland lakes was 6.3%, at Long Point Inner Bay was 8.7%, at other bays and harbors was 14.6% and at tributary sites was 12.5%. Overall, 93% of the raised lesions identified as presumptive tumors grossly were verified as neoplasms microscopically. The prevalence of orocutaneous tumors increased with age at both Presque Isle Bay and Long Point Inner Bay, the sites with the largest sample sizes.

Induced earthquake magnitudes are as large as (statistically) expected

USGS Publications Warehouse

Van Der Elst, Nicholas; Page, Morgan T.; Weiser, Deborah A.; Goebel, Thomas; Hosseini, S. Mehran

2016-01-01

A major question for the hazard posed by injection-induced seismicity is how large induced earthquakes can be. Are their maximum magnitudes determined by injection parameters or by tectonics? Deterministic limits on induced earthquake magnitudes have been proposed based on the size of the reservoir or the volume of fluid injected. However, if induced earthquakes occur on tectonic faults oriented favorably with respect to the tectonic stress field, then they may be limited only by the regional tectonics and connectivity of the fault network. In this study, we show that the largest magnitudes observed at fluid injection sites are consistent with the sampling statistics of the Gutenberg-Richter distribution for tectonic earthquakes, assuming no upper magnitude bound. The data pass three specific tests: (1) the largest observed earthquake at each site scales with the log of the total number of induced earthquakes, (2) the order of occurrence of the largest event is random within the induced sequence, and (3) the injected volume controls the total number of earthquakes rather than the total seismic moment. All three tests point to an injection control on earthquake nucleation but a tectonic control on earthquake magnitude. Given that the largest observed earthquakes are exactly as large as expected from the sampling statistics, we should not conclude that these are the largest earthquakes possible. Instead, the results imply that induced earthquake magnitudes should be treated with the same maximum magnitude bound that is currently used to treat seismic hazard from tectonic earthquakes.

Searches for point sources in the Galactic Center region

NASA Astrophysics Data System (ADS)

di Mauro, Mattia; Fermi-LAT Collaboration

2017-01-01

Several groups have demonstrated the existence of an excess in the gamma-ray emission around the Galactic Center (GC) with respect to the predictions from a variety of Galactic Interstellar Emission Models (GIEMs) and point source catalogs. The origin of this excess, peaked at a few GeV, is still under debate. A possible interpretation is that it comes from a population of unresolved Millisecond Pulsars (MSPs) in the Galactic bulge. We investigate the detection of point sources in the GC region using new tools which the Fermi-LAT Collaboration is developing in the context of searches for Dark Matter (DM) signals. These new tools perform very fast scans iteratively testing for additional point sources at each of the pixels of the region of interest. We show also how to discriminate between point sources and structural residuals from the GIEM. We apply these methods to the GC region considering different GIEMs and testing the DM and MSPs intepretations for the GC excess. Additionally, we create a list of promising MSP candidates that could represent the brightest sources of a MSP bulge population.

Analysis of non-point and point source pollution in China: case study in Shima Watershed in Guangdong Province

NASA Astrophysics Data System (ADS)

Fang, Huaiyang; Lu, Qingshui; Gao, Zhiqiang; Shi, Runhe; Gao, Wei

2013-09-01

China economy has been rapidly increased since 1978. Rapid economic growth led to fast growth of fertilizer and pesticide consumption. A significant portion of fertilizers and pesticides entered the water and caused water quality degradation. At the same time, rapid economic growth also caused more and more point source pollution discharge into the water. Eutrophication has become a major threat to the water bodies. Worsening environment problems forced governments to take measures to control water pollution. We extracted land cover from Landsat TM images; calculated point source pollution with export coefficient method; then SWAT model was run to simulate non-point source pollution. We found that the annual TP loads from industry pollution into rivers are 115.0 t in the entire watershed. Average annual TP loads from each sub-basin ranged from 0 to 189.4 ton. Higher TP loads of each basin from livestock and human living mainly occurs in the areas where they are far from large towns or cities and the TP loads from industry are relatively low. Mean annual TP loads that delivered to the streams was 246.4 tons and the highest TP loads occurred in north part of this area, and the lowest TP loads is mainly distributed in middle part. Therefore, point source pollution has much high proportion in this area and governments should take measures to control point source pollution.

Localization of beta and high-frequency oscillations within the subthalamic nucleus region.

PubMed

van Wijk, B C M; Pogosyan, A; Hariz, M I; Akram, H; Foltynie, T; Limousin, P; Horn, A; Ewert, S; Brown, P; Litvak, V

2017-01-01

Parkinsonian bradykinesia and rigidity are typically associated with excessive beta band oscillations in the subthalamic nucleus. Recently another spectral peak has been identified that might be implicated in the pathophysiology of the disease: high-frequency oscillations (HFO) within the 150-400 Hz range. Beta-HFO phase-amplitude coupling (PAC) has been found to correlate with severity of motor impairment. However, the neuronal origin of HFO and its usefulness as a potential target for deep brain stimulation remain to be established. For example, it is unclear whether HFO arise from the same neural populations as beta oscillations. We intraoperatively recorded local field potentials from the subthalamic nucleus while advancing DBS electrodes in 2 mm steps from 4 mm above the surgical target point until 2 mm below, resulting in 4 recording sites. Data from 26 nuclei from 14 patients were analysed. For each trajectory, we identified the recording site with the largest spectral peak in the beta range (13-30 Hz), and the largest peak in the HFO range separately. In addition, we identified the recording site with the largest beta-HFO PAC. Recording sites with largest beta power and largest HFO power coincided in 50% of cases. In the other 50%, HFO was more likely to be detected at a more superior recording site in the target area. PAC followed more closely the site with largest HFO (45%) than beta power (27%). HFO are likely to arise from spatially close, but slightly more superior neural populations than beta oscillations. Further work is necessary to determine whether the different activities can help fine-tune deep brain stimulation targeting.

Recent updates in developing a statistical pseudo-dynamic source-modeling framework to capture the variability of earthquake rupture scenarios

NASA Astrophysics Data System (ADS)

Song, Seok Goo; Kwak, Sangmin; Lee, Kyungbook; Park, Donghee

2017-04-01

It is a critical element to predict the intensity and variability of strong ground motions in seismic hazard assessment. The characteristics and variability of earthquake rupture process may be a dominant factor in determining the intensity and variability of near-source strong ground motions. Song et al. (2014) demonstrated that the variability of earthquake rupture scenarios could be effectively quantified in the framework of 1-point and 2-point statistics of earthquake source parameters, constrained by rupture dynamics and past events. The developed pseudo-dynamic source modeling schemes were also validated against the recorded ground motion data of past events and empirical ground motion prediction equations (GMPEs) at the broadband platform (BBP) developed by the Southern California Earthquake Center (SCEC). Recently we improved the computational efficiency of the developed pseudo-dynamic source-modeling scheme by adopting the nonparametric co-regionalization algorithm, introduced and applied in geostatistics initially. We also investigated the effect of earthquake rupture process on near-source ground motion characteristics in the framework of 1-point and 2-point statistics, particularly focusing on the forward directivity region. Finally we will discuss whether the pseudo-dynamic source modeling can reproduce the variability (standard deviation) of empirical GMPEs and the efficiency of 1-point and 2-point statistics to address the variability of ground motions.

VizieR Online Data Catalog: The XMM-Newton 2nd Incremental Source Catalogue (2XMMi) (XMM-SSC, 2008)

NASA Astrophysics Data System (ADS)

Xmm-Newton Survey Science Centre, Consortium

2007-09-01

The 2XMMi catalogue is the fourth publicly released XMM X-ray source catalogue produced by the XMM Survey Science Centre (SSC) consortium, following the 1XMM (Cat. IX/37, released in April 2003), 2XMMp (July 2006) and 2XMM (Cat. IX/39, August 2007) catalogues: 2XMMp was a preliminary version of 2XMM. 2XMMi is an incremental version of the 2XMM catalogue. The 2XMMi catalogue is about 17% larger than the 2XMM catalogue, which it supersedes, due to the 1-year longer baseline of observations included (it is about 8 times larger than the 1XMM catalogue). As such, it is the largest X-ray source catalogue ever produced, containing more than twice as many discrete sources as either the ROSAT survey or pointed catalogues. 2XMMi complements deeper Chandra and XMM-Newton small area surveys, probing a large sky area at the flux limit where the bulk of the objects that contribute to the X-ray background lie. The 2XMMi catalogue provides a rich resource for generating large, well-defined samples for specific studies, utilizing the fact that X-ray selection is a highly efficient (arguably the most efficient) way of selecting certain types of object, notably active galaxies (AGN), clusters of galaxies, interacting compact binaries and active stellar coronae. The large sky area covered by the serendipitous survey, or equivalently the large size of the catalogue, also means that 2XMMi is a superb resource for exploring the variety of the X-ray source population and identifying rare source types. The production of the 2XMMi catalogue has been undertaken by the XMM-Newton SSC consortium in fulfilment of one of its major responsibilities within the XMM-Newton project. The catalogue production process has been designed to exploit fully the capabilities of the XMM-Newton EPIC cameras and to ensure the integrity and quality of the resultant catalogue through rigorous screening of the data. The predecessor 2XMM catalogue was made from a subset of public observations emerging from a re-processing (in 2006/7) of all XMM observations made prior to that point. The creation of the incremental 2XMMi catalogue has been driven by the desire to make public the additional data from that re-processing that were proprietary at the time of the 2XMM release but which subsequently became public before 01 May 2008. These have been augmented with a further 90 observations that have been processed more recently as part of the routine, day-to-day XMM data processing performed by the SSC, which were also public at 01 May 2008. Together, these amount to 626 additional observations (18%) with respect to 2XMM. With these new data, the sky area covered grows by 19% while the number of detections increases by 17% and the number of unique sources by 15%. A key factor in the decision to make the 2XMMi catalogue is the fact that, effectively, all the new data have been processed with the same science analysis software (SAS), pipeline and calibration as used in the aforementioned re-processing. As such, the products from 2XMM and from the new observations form a set of uniformly processed data. With software and calibration changes now being propagated into the SSC processing pipeline, it was deemed timely to make public the largest available uniform catalogue. The catalogue in its FITS version file (2xmmi.fit) has 246897 entries made of 297 columns; a 'slim' version gathering the 39 most relevant columns for the 191870 unique sources detected, is available as an ascii table or a FITS binary table. In both versions, the columns are fully described in the XMM-Newton User Guide available from: http://xmmssc-www.star.le.ac.uk/Catalogue/UserGuide_xmmcat.html The original names of these columns are included in the "Byte-by-byte Description" below (uppercase names within parentheses) Details about the construction of the catalogue can be found from the XMM-Newton Survey Science Centre (http://xmmssc-www.star.le.ac.uk/) (2 data files).

VizieR Online Data Catalog: The XMM-Newton 2nd Incremental Source Catalogue (2XMMi) (XMM-SSC, 2008)

NASA Astrophysics Data System (ADS)

Xmm-Newton Survey Science Centre, Consortium

2008-09-01

The 2XMMi catalogue is the fourth publicly released XMM X-ray source catalogue produced by the XMM Survey Science Centre (SSC) consortium, following the 1XMM (Cat. IX/37, released in April 2003), 2XMMp (July 2006) and 2XMM (Cat. IX/39, August 2007) catalogues: 2XMMp was a preliminary version of 2XMM. 2XMMi is an incremental version of the 2XMM catalogue. The 2XMMi catalogue is about 17% larger than the 2XMM catalogue, which it supersedes, due to the 1-year longer baseline of observations included (it is about 8 times larger than the 1XMM catalogue). As such, it is the largest X-ray source catalogue ever produced, containing more than twice as many discrete sources as either the ROSAT survey or pointed catalogues. 2XMMi complements deeper Chandra and XMM-Newton small area surveys, probing a large sky area at the flux limit where the bulk of the objects that contribute to the X-ray background lie. The 2XMMi catalogue provides a rich resource for generating large, well-defined samples for specific studies, utilizing the fact that X-ray selection is a highly efficient (arguably the most efficient) way of selecting certain types of object, notably active galaxies (AGN), clusters of galaxies, interacting compact binaries and active stellar coronae. The large sky area covered by the serendipitous survey, or equivalently the large size of the catalogue, also means that 2XMMi is a superb resource for exploring the variety of the X-ray source population and identifying rare source types. The production of the 2XMMi catalogue has been undertaken by the XMM-Newton SSC consortium in fulfilment of one of its major responsibilities within the XMM-Newton project. The catalogue production process has been designed to exploit fully the capabilities of the XMM-Newton EPIC cameras and to ensure the integrity and quality of the resultant catalogue through rigorous screening of the data. The predecessor 2XMM catalogue was made from a subset of public observations emerging from a re-processing (in 2006/7) of all XMM observations made prior to that point. The creation of the incremental 2XMMi catalogue has been driven by the desire to make public the additional data from that re-processing that were proprietary at the time of the 2XMM release but which subsequently became public before 01 May 2008. These have been augmented with a further 90 observations that have been processed more recently as part of the routine, day-to-day XMM data processing performed by the SSC, which were also public at 01 May 2008. Together, these amount to 626 additional observations (18%) with respect to 2XMM. With these new data, the sky area covered grows by 19% while the number of detections increases by 17% and the number of unique sources by 15%. A key factor in the decision to make the 2XMMi catalogue is the fact that, effectively, all the new data have been processed with the same science analysis software (SAS), pipeline and calibration as used in the aforementioned re-processing. As such, the products from 2XMM and from the new observations form a set of uniformly processed data. With software and calibration changes now being propagated into the SSC processing pipeline, it was deemed timely to make public the largest available uniform catalogue. The catalogue in its FITS version file (2xmmi.fit) has 246897 entries made of 297 columns; a 'slim' version gathering the 39 most relevant columns for the 191870 unique sources detected, is available as an ascii table or a FITS binary table. In both versions, the columns are fully described in the XMM-Newton User Guide available from: http://xmmssc-www.star.le.ac.uk/Catalogue/UserGuide_xmmcat.html The original names of these columns are included in the "Byte-by-byte Description" below (uppercase names within parentheses) Details about the construction of the catalogue can be found from the XMM-Newton Survey Science Centre (http://xmmssc-www.star.le.ac.uk/) (2 data files).

Point and Compact Hα Sources in the Interior of M33

NASA Astrophysics Data System (ADS)

Moody, J. Ward; Hintz, Eric G.; Joner, Michael D.; Roming, Peter W. A.; Hintz, Maureen L.

2017-12-01

A variety of interesting objects such as Wolf-Rayet stars, tight OB associations, planetary nebulae, X-ray binaries, etc., can be discovered as point or compact sources in Hα surveys. How these objects distribute through a galaxy sheds light on the galaxy star formation rate and history, mass distribution, and dynamics. The nearby galaxy M33 is an excellent place to study the distribution of Hα-bright point sources in a flocculant spiral galaxy. We have reprocessed an archived WIYN continuum-subtracted Hα image of the inner 6.‧5 × 6.‧5 of M33 and, employing both eye and machine searches, have tabulated sources with a flux greater than approximately 10-15 erg cm-2s-1. We have effectively recovered previously mapped H II regions and have identified 152 unresolved point sources and 122 marginally resolved compact sources, of which 39 have not been previously identified in any archive. An additional 99 Hα sources were found to have sufficient archival flux values to generate a Spectral Energy Distribution. Using the SED, flux values, Hα flux value, and compactness, we classified 67 of these sources.

[Estimation of nonpoint source pollutant loads and optimization of the best management practices (BMPs) in the Zhangweinan River basin].

PubMed

Xu, Hua-Shan; Xu, Zong-Xue; Liu, Pin

2013-03-01

One of the key techniques in establishing and implementing TMDL (total maximum daily load) is to utilize hydrological model to quantify non-point source pollutant loads, establish BMPs scenarios, reduce non-point source pollutant loads. Non-point source pollutant loads under different years (wet, normal and dry year) were estimated by using SWAT model in the Zhangweinan River basin, spatial distribution characteristics of non-point source pollutant loads were analyzed on the basis of the simulation result. During wet years, total nitrogen (TN) and total phosphorus (TP) accounted for 0.07% and 27.24% of the total non-point source pollutant loads, respectively. Spatially, agricultural and residential land with steep slope are the regions that contribute more non-point source pollutant loads in the basin. Compared to non-point source pollutant loads with those during the baseline period, 47 BMPs scenarios were set to simulate the reduction efficiency of different BMPs scenarios for 5 kinds of pollutants (organic nitrogen, organic phosphorus, nitrate nitrogen, dissolved phosphorus and mineral phosphorus) in 8 prior controlled subbasins. Constructing vegetation type ditch was optimized as the best measure to reduce TN and TP by comparing cost-effective relationship among different BMPs scenarios, and the costs of unit pollutant reduction are 16.11-151.28 yuan x kg(-1) for TN, and 100-862.77 yuan x kg(-1) for TP, which is the most cost-effective measure among the 47 BMPs scenarios. The results could provide a scientific basis and technical support for environmental protection and sustainable utilization of water resources in the Zhangweinan River basin.

Dung beetles (Coleoptera: Scarabaeidae) attracted to dung of the largest herbivorous rodent on earth: a comparison with human feces.

PubMed

Puker, Anderson; Correa, César M A; Korasaki, Vanesca; Ferreira, Kleyton R; Oliveira, Naiara G

2013-12-01

The capybara, Hydrochoerus hydrochaeris (L.) (Rodentia: Caviidae), is the largest herbivorous rodent on Earth and abundant in the Neotropical region, which can provide a stable food source of dung for dung beetle communities (Coleoptera: Scarabaeidae: Scarabaeinae). However, the use of capybara dung by dung beetles is poorly known. Here, we present data on the structure of the dung beetle community attracted to capybara dung and compare with the community attracted to human feces. Dung beetles were captured with pitfall traps baited with fresh capybara dung and human feces in pastures with exotic grass (Brachiaria spp.), patches of Brazilian savanna (Cerrado), and points of degraded riparian vegetation along the Aquidauana river in Anastácio and Aquidauana, Mato Grosso do Sul, Brazil. In traps baited with human feces, 13,809 individuals of 31 species were captured, and in those baited with capybara dung 1,027 individuals belonging to 26 species were captured. The average number of individuals and species captured by the traps baited with human feces was greater than for capybara dung in all habitats studied. Composition of the communities attracted to human feces and capybara dung formed distinct groups in all habitats. Despite the smaller number of species and individuals captured in capybara dung when compared with human feces, capybara dung was attractive to dung beetles. In Brazil, the legalization of hunting these rodents has been debated, which would potentially affect the community and consequently the ecological functions performed by dung beetles that use the feces of these animals as a resource. In addition, the knowledge of the communities associated with capybaras may be important in predicting the consequences of future management of their populations.

An assessment of urban form and pedestrian and transit improvements as an integrated GHG reduction strategy.

DOT National Transportation Integrated Search

2011-04-01

In the last several years, Washington State has adopted a series of policy goals intended to : reduce greenhouse gases (GHGs). Because transportation is one of the states largest sources of : GHG emissions, the Washington State Department of Trans...

Spatiotemporal characteristics of organic contaminant concentrations and ecological risk assessment in the Songhua River, China

EPA Science Inventory

To control source pollution and improve water quality, an understanding of the spatiotemporal characteristics of organic contaminant concentrations in affected receiving waters is necessary. The Songhua River in northeast China is the country's third-largest domestic river and lo...

Cloning and characterization of alpha-glucuronidase enzyme

USDA-ARS?s Scientific Manuscript database

Hemicellulose is the second largest source of biomass on Earth. Xylan, a polymer of beta-1,4-linked xylose residues, is a common component of hemicellulose. The enzymes xylanase and beta-xylosidase hydrolyze the xylan into xylose which can then be fermented into value-added products. However, the...

Impact of cascadia subduction zone earthquake on the seismic evaluation criteria of bridges : technical report : SPR 770.

DOT National Transportation Integrated Search

2016-12-01

A large magnitude long duration subduction earthquake is impending in the Pacific Northwest, which lies near the : Cascadia Subduction Zone (CSZ). Great subduction zone earthquakes are the largest earthquakes in the world and are the sole source : zo...

Comparison of Varied Precipitation and Soil Data Types for Use in Watershed Modeling.

EPA Science Inventory

The accuracy of water quality and quantity models depends on calibration to ensure reliable simulations of streamflow, which in turn requires accurate climatic forcing data. Precipitation is widely acknowledged to be the largest source of uncertainty in watershed modeling, and so...

In vitro to in vivo extrapolation of hepatic metabolism in fish: An inter-laboratory comparison of in vitro methods - presentation

EPA Science Inventory

Chemical biotransformation represents the largest source of uncertainty in chemical bioaccumulation assessments. Model-based estimates of chemical bioconcentration in fish may be greatly improved by including biotransformation rates, as measured in vitro. Substrate depletion assa...

CTEPP DATA COLLECTION FORM 02: HOUSE/BUILDING CHARACTERISTICS OBSERVATION SURVEY FOR THE HOME

EPA Science Inventory

This data collection form is used to document the physical characteristics of the home and identify and inventory possible sources of pollutants.

The Children's Total Exposure to Persistent Pesticides and Other Persistent Pollutant (CTEPP) study was one of the largest aggregate...

Occupational Tedium among Prison Officers.

ERIC Educational Resources Information Center

Shamir, Boaz; Drory, Amos

1982-01-01

Studied sources of occupational stress in the prison officer's job and investigated their relationships with tedium (defined as a general experience of physical, emotional, and attitudinal exhaustion). Found the variables making the largest unique contributions to the variance in tedium are role overload, management support, and societal support.…

DEVELOPMENT OF REAL-TIME FLARE COMBUSTION EFFICIENCY MONITOR - PHASE I

EPA Science Inventory

There are approximately 7,000 flares in operation at industrial facilities across the United States. Flares are one of the largest Volatile Organic Compounds (VOCs) and air toxics emissions sources. Based on a special emission inventory required by the Texas Commission on E...

Report: Enhanced EPA Oversight Needed to Address Risks From Declining Clean Air Act Title V Revenues

EPA Pesticide Factsheets

Report #15-P-0006, October 20, 2014. Weaknesses in the EPA's oversight of Title V revenues and expenditures jeopardize program implementation and, in turn, compliance with air regulations for many of the nation's largest sources of air pollution.

Regional Scale Photochemical Model Evaluation of Total Mercury Wet Deposition and Speciated Ambient Mercury

EPA Science Inventory

Methylmercury is a known neurotoxin with deleterious health effects on humans and wildlife. Atmospheric deposition is the largest source of mercury loading to most terrestrial and aquatic ecosystems. Regional scale air quality models are needed to quantify mercury deposition resu...

Combining stable isotopes with contamination indicators: A method for improved investigation of nitrate sources and dynamics in aquifers with mixed nitrogen inputs.

PubMed

Minet, E P; Goodhue, R; Meier-Augenstein, W; Kalin, R M; Fenton, O; Richards, K G; Coxon, C E

2017-11-01

Excessive nitrate (NO 3 - ) concentration in groundwater raises health and environmental issues that must be addressed by all European Union (EU) member states under the Nitrates Directive and the Water Framework Directive. The identification of NO 3 - sources is critical to efficiently control or reverse NO 3 - contamination that affects many aquifers. In that respect, the use of stable isotope ratios 15 N/ 14 N and 18 O/ 16 O in NO 3 - (expressed as δ 15 N-NO 3 - and δ 18 O-NO 3 - , respectively) has long shown its value. However, limitations exist in complex environments where multiple nitrogen (N) sources coexist. This two-year study explores a method for improved NO 3 - source investigation in a shallow unconfined aquifer with mixed N inputs and a long established NO 3 - problem. In this tillage-dominated area of free-draining soil and subsoil, suspected NO 3 - sources were diffuse applications of artificial fertiliser and organic point sources (septic tanks and farmyards). Bearing in mind that artificial diffuse sources were ubiquitous, groundwater samples were first classified according to a combination of two indicators relevant of point source contamination: presence/absence of organic point sources (i.e. septic tank and/or farmyard) near sampling wells and exceedance/non-exceedance of a contamination threshold value for sodium (Na + ) in groundwater. This classification identified three contamination groups: agricultural diffuse source but no point source (D+P-), agricultural diffuse and point source (D+P+) and agricultural diffuse but point source occurrence ambiguous (D+P±). Thereafter δ 15 N-NO 3 - and δ 18 O-NO 3 - data were superimposed on the classification. As δ 15 N-NO 3 - was plotted against δ 18 O-NO 3 - , comparisons were made between the different contamination groups. Overall, both δ variables were significantly and positively correlated (p < 0.0001, r s  = 0.599, slope of 0.5), which was indicative of denitrification. An inspection of the contamination groups revealed that denitrification did not occur in the absence of point source contamination (group D+P-). In fact, strong significant denitrification lines occurred only in the D+P+ and D+P± groups (p < 0.0001, r s  > 0.6, 0.53 ≤ slope ≤ 0.76), i.e. where point source contamination was characterised or suspected. These lines originated from the 2-6‰ range for δ 15 N-NO 3 - , which suggests that i) NO 3 - contamination was dominated by an agricultural diffuse N source (most likely the large organic matter pool that has incorporated 15 N-depleted nitrogen from artificial fertiliser in agricultural soils and whose nitrification is stimulated by ploughing and fertilisation) rather than point sources and ii) denitrification was possibly favoured by high dissolved organic content (DOC) from point sources. Combining contamination indicators and a large stable isotope dataset collected over a large study area could therefore improve our understanding of the NO 3 - contamination processes in groundwater for better land use management. We hypothesise that in future research, additional contamination indicators (e.g. pharmaceutical molecules) could also be combined to disentangle NO 3 - contamination from animal and human wastes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Backscattering of sound from targets in an Airy caustic formed by a curved reflecting surface

NASA Astrophysics Data System (ADS)

Dzikowicz, Benjamin Robert

The focusing of a caustic associated with the reflection of a locally curved sea floor or surface affects the scattering of sound by underwater targets. The most elementary caustic formed when sound reflects off a naturally curved surface is an Airy caustic. The case of a spherical target is examined here. With a point source acting also as a receiver, a point target lying in a shadow region returns only one echo directly from the target. When the target is on the Airy caustic, there are two echoes: one path is directly to the target and the other focuses off the curved surface. Echoes may be focused in both directions, the doubly focused case being the largest and the latest echo. With the target in the lit region, these different paths produce multiple echoes. For a finite sized sphere near an Airy caustic, all these echoes are manifest, but they occur at shifted target positions. Echoes of tone bursts reflecting only once overlap and interfere with each other, as do those reflecting twice. Catastrophe theory is used to analyze the echo amplitudes arising from these overlaps. The echo pressure for single reflections is shown to have a dependence on target position described by an Airy function for both a point and a finite target. With double focusing, this dependence is the square of an Airy function for a point target. With a finite sized target, (as in the experiment) this becomes a hyperbolic umbilic catastrophe integral with symmetric arguments. The arguments of each of these functions are derived from only the relative echo times of a transient pulse. Transient echo times are calculated using a numerical ray finding technique. Experiment confirms the predicted merging of transient echoes in the time domain, as well as the Airy and hyperbolic umbilic diffraction integral amplitudes for a tone burst. This method allows targets to be observed at greater distances in the presence of a focusing surface.

Skyshine at neutron energies less than or equal to 400 MeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alsmiller, A.G. Jr.; Barish, J.; Childs, R.L.

1980-10-01

The dose equivalent at an air-ground interface as a function of distance from an assumed azimuthally symmetric point source of neutrons can be calculated as a double integral. The integration is over the source strength as a function of energy and polar angle weighted by an importance function that depends on the source variables and on the distance from the source to the filed point. The neutron importance function for a source 15 m above the ground emitting only into the upper hemisphere has been calculated using the two-dimensional discrete ordinates code, DOT, and the first collision source code, GRTUNCL,more » in the adjoint mode. This importance function is presented for neutron energies less than or equal to 400 MeV, for source cosine intervals of 1 to .8, .8 to .6 to .4, .4 to .2 and .2 to 0, and for various distances from the source to the field point. As part of the adjoint calculations a photon importance function is also obtained. This importance function for photon energies less than or equal to 14 MEV and for various source cosine intervals and source-to-field point distances is also presented. These importance functions may be used to obtain skyshine dose equivalent estimates for any known source energy-angle distribution.« less

Outlier Resistant Predictive Source Encoding for a Gaussian Stationary Nominal Source.

DTIC Science & Technology

1987-09-18

breakdown point and influence function . The proposed sequence of predictive encoders attains strictly positive breakdown point and uniformly bounded... influence function , at the expense of increased mean difference-squared distortion and differential entropy, at the Gaussian nominal source.

Source Model of the MJMA 6.5 Plate-Boundary Earthquake at the Nankai Trough, Southwest Japan, on April 1, 2016, Based on Strong Motion Waveform Modeling

NASA Astrophysics Data System (ADS)

Asano, K.

2017-12-01

An MJMA 6.5 earthquake occurred offshore the Kii peninsula, southwest Japan on April 1, 2016. This event was interpreted as a thrust-event on the plate-boundary along the Nankai trough where (Wallace et al., 2016). This event is the largest plate-boundary earthquake in the source region of the 1944 Tonankai earthquake (MW 8.0) after that event. The significant point of this event regarding to seismic observation is that this event occurred beneath an ocean-bottom seismic network called DONET1, which is jointly operated by NIED and JAMSTEC. Since moderate-to-large earthquake of this focal type is very rare in this region in the last half century, it is a good opportunity to investigate the source characteristics relating to strong motion generation of subduction-zone plate-boundary earthquakes along the Nankai trough. Knowledge obtained from the study of this earthquake would contribute to ground motion prediction and seismic hazard assessment for future megathrust earthquakes expected in the Nankai trough. In this study, the source model of the 2016 offshore the Kii peninsula earthquake was estimated by broadband strong motion waveform modeling using the empirical Green's function method (Irikura, 1986). The source model is characterized by strong motion generation area (SMGA) (Miyake et al., 2003), which is defined as a rectangular area with high-stress drop or high slip-velocity. SMGA source model based on the empirical Green's function method has great potential to reproduce ground motion time history in broadband frequency range. We used strong motion data from offshore stations (DONET1 and LTBMS) and onshore stations (NIED F-net and DPRI). The records of an MJMA 3.2 aftershock at 13:04 on April 1, 2016 were selected for the empirical Green's functions. The source parameters of SMGA are optimized by the waveform modeling in the frequency range 0.4-10 Hz. The best estimate of SMGA size is 19.4 km2, and SMGA of this event does not follow the source scaling relationship for past plate-boundary earthquakes along the Japan trench, northeast Japan. This finding implies that the source characteristics of plate-boundary events in the Nankai trough are different from those in the Japan Trench, and it could be important information to consider regional variation in ground motion prediction.

Mapping algorithm for freeform construction using non-ideal light sources

NASA Astrophysics Data System (ADS)

Li, Chen; Michaelis, D.; Schreiber, P.; Dick, L.; Bräuer, A.

2015-09-01

Using conventional mapping algorithms for the construction of illumination freeform optics' arbitrary target pattern can be obtained for idealized sources, e.g. collimated light or point sources. Each freeform surface element generates an image point at the target and the light intensity of an image point is corresponding to the area of the freeform surface element who generates the image point. For sources with a pronounced extension and ray divergence, e.g. an LED with a small source-freeform-distance, the image points are blurred and the blurred patterns might be different between different points. Besides, due to Fresnel losses and vignetting, the relationship between light intensity of image points and area of freeform surface elements becomes complicated. These individual light distributions of each freeform element are taken into account in a mapping algorithm. To this end the method of steepest decent procedures are used to adapt the mapping goal. A structured target pattern for a optics system with an ideal source is computed applying corresponding linear optimization matrices. Special weighting factor and smoothing factor are included in the procedures to achieve certain edge conditions and to ensure the manufacturability of the freefrom surface. The corresponding linear optimization matrices, which are the lighting distribution patterns of each of the freeform surface elements, are gained by conventional raytracing with a realistic source. Nontrivial source geometries, like LED-irregularities due to bonding or source fine structures, and a complex ray divergence behavior can be easily considered. Additionally, Fresnel losses, vignetting and even stray light are taken into account. After optimization iterations, with a realistic source, the initial mapping goal can be achieved by the optics system providing a structured target pattern with an ideal source. The algorithm is applied to several design examples. A few simple tasks are presented to discussed the ability and limitation of the this mothed. It is also presented that a homogeneous LED-illumination system design, in where, with a strongly tilted incident direction, a homogeneous distribution is achieved with a rather compact optics system and short working distance applying a relatively large LED source. It is shown that the lighting distribution patterns from the freeform surface elements can be significantly different from the others. The generation of a structured target pattern, applying weighting factor and smoothing factor, are discussed. Finally, freeform designs for much more complex sources like clusters of LED-sources are presented.

A selective array activation method for the generation of a focused source considering listening position.

PubMed

Song, Min-Ho; Choi, Jung-Woo; Kim, Yang-Hann

2012-02-01

A focused source can provide an auditory illusion of a virtual source placed between the loudspeaker array and the listener. When a focused source is generated by time-reversed acoustic focusing solution, its use as a virtual source is limited due to artifacts caused by convergent waves traveling towards the focusing point. This paper proposes an array activation method to reduce the artifacts for a selected listening point inside an array of arbitrary shape. Results show that energy of convergent waves can be reduced up to 60 dB for a large region including the selected listening point. © 2012 Acoustical Society of America

Chandra Observations of the M31

NASA Technical Reports Server (NTRS)

Garcia, Michael; Lavoie, Anthony R. (Technical Monitor)

2000-01-01

We report on Chandra observations of the nearest Spiral Galaxy, M3l, The nuclear source seen with previous X-ray observatories is resolved into five point sources. One of these sources is within 1 arc-sec of the M31 central super-massive black hole. As compared to the other point sources in M3l. this nuclear source has an unusually soft spectrum. Based on the spatial coincidence and the unusual spectrum. we identify this source with the central black hole. A bright transient is detected 26 arc-sec to the west of the nucleus, which may be associated with a stellar mass black hole. We will report on a comparison of the x-ray spectrum of the diffuse emission and point sources seen in the central few arcmin

Waveform inversion of volcano-seismic signals for an extended source

USGS Publications Warehouse

Nakano, M.; Kumagai, H.; Chouet, B.; Dawson, P.

2007-01-01

We propose a method to investigate the dimensions and oscillation characteristics of the source of volcano-seismic signals based on waveform inversion for an extended source. An extended source is realized by a set of point sources distributed on a grid surrounding the centroid of the source in accordance with the source geometry and orientation. The source-time functions for all point sources are estimated simultaneously by waveform inversion carried out in the frequency domain. We apply a smoothing constraint to suppress short-scale noisy fluctuations of source-time functions between adjacent sources. The strength of the smoothing constraint we select is that which minimizes the Akaike Bayesian Information Criterion (ABIC). We perform a series of numerical tests to investigate the capability of our method to recover the dimensions of the source and reconstruct its oscillation characteristics. First, we use synthesized waveforms radiated by a kinematic source model that mimics the radiation from an oscillating crack. Our results demonstrate almost complete recovery of the input source dimensions and source-time function of each point source, but also point to a weaker resolution of the higher modes of crack oscillation. Second, we use synthetic waveforms generated by the acoustic resonance of a fluid-filled crack, and consider two sets of waveforms dominated by the modes with wavelengths 2L/3 and 2W/3, or L and 2L/5, where W and L are the crack width and length, respectively. Results from these tests indicate that the oscillating signature of the 2L/3 and 2W/3 modes are successfully reconstructed. The oscillating signature of the L mode is also well recovered, in contrast to results obtained for a point source for which the moment tensor description is inadequate. However, the oscillating signature of the 2L/5 mode is poorly recovered owing to weaker resolution of short-scale crack wall motions. The triggering excitations of the oscillating cracks are successfully reconstructed. Copyright 2007 by the American Geophysical Union.

Genuine non-self-averaging and ultraslow convergence in gelation.

PubMed

Cho, Y S; Mazza, M G; Kahng, B; Nagler, J

2016-08-01

In irreversible aggregation processes droplets or polymers of microscopic size successively coalesce until a large cluster of macroscopic scale forms. This gelation transition is widely believed to be self-averaging, meaning that the order parameter (the relative size of the largest connected cluster) attains well-defined values upon ensemble averaging with no sample-to-sample fluctuations in the thermodynamic limit. Here, we report on anomalous gelation transition types. Depending on the growth rate of the largest clusters, the gelation transition can show very diverse patterns as a function of the control parameter, which includes multiple stochastic discontinuous transitions, genuine non-self-averaging and ultraslow convergence of the transition point. Our framework may be helpful in understanding and controlling gelation.

Source apportionment of trace metals in river sediments: A comparison of three methods.

PubMed

Chen, Haiyang; Teng, Yanguo; Li, Jiao; Wu, Jin; Wang, Jinsheng

2016-04-01

Increasing trace metal pollution in river sediment poses a significant threat to watershed ecosystem health. Identifying potential sources of sediment metals and apportioning their contributions are of key importance for proposing prevention and control strategies of river pollution. In this study, three advanced multivariate receptor models, factor analysis with nonnegative constraints (FA-NNC), positive matrix factorization (PMF), and multivariate curve resolution weighted-alternating least-squares (MCR-WALS), were comparatively employed for source apportionment of trace metals in river sediments and applied to the Le'an River, a main tributary of Poyang Lake which is the largest freshwater lake in China. The pollution assessment with contamination factor and geoaccumulation index suggested that the river sediments in Le'an River were contaminated severely by trace metals due to human activities. With the three apportionment tools, similar source profiles of trace metals in sediments were extracted. Especially, the MCR-WALS and PMF models produced essentially the same results. Comparatively speaking, the weighted schemes might give better solutions than the unweighted FA-NNC because the uncertainty information of environmental data was considered by PMF and MCR-WALS. Anthropogenic sources were apportioned as the most important pollution sources influencing the sediment metals in Le'an River with contributions of about 90%. Among them, copper tailings occupied the largest contribution (38.4-42.2%), followed by mining wastewater (29.0-33.5%), and agricultural activities (18.2-18.7%). To protect the ecosystem of Le'an River and Poyang Lake, special attention should be paid to the discharges of mining wastewater and the leachates of copper tailing ponds in that region. Copyright © 2015 Elsevier Ltd. All rights reserved.

Distributed optimization system and method

DOEpatents

Hurtado, John E.; Dohrmann, Clark R.; Robinett, III, Rush D.

2003-06-10

A search system and method for controlling multiple agents to optimize an objective using distributed sensing and cooperative control. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace. The objective can be: chemical sources, temperature sources, radiation sources, light sources, evaders, trespassers, explosive sources, time dependent sources, time independent sources, function surfaces, maximization points, minimization points, and optimal control of a system such as a communication system, an economy, a crane, and a multi-processor computer.

Distributed Optimization System

DOEpatents

Hurtado, John E.; Dohrmann, Clark R.; Robinett, III, Rush D.

2004-11-30

A search system and method for controlling multiple agents to optimize an objective using distributed sensing and cooperative control. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace. The objective can be: chemical sources, temperature sources, radiation sources, light sources, evaders, trespassers, explosive sources, time dependent sources, time independent sources, function surfaces, maximization points, minimization points, and optimal control of a system such as a communication system, an economy, a crane, and a multi-processor computer.

An Institutional Approach to Course Redesign at a Hispanic-Serving Institution

ERIC Educational Resources Information Center

Sanchez, Rudolph J.; Ramirez, Adrian D.; Hernandez, Chris

2013-01-01

As with many higher education institutions, Fresno State struggles with graduation rates. The overall six-year graduation rate for first-time, full-time freshmen hovers around 50 percent. The graduation gap between the two largest ethnic groups, White (55.6) and Hispanic (43.5), was 12.1 percentage points in 2012. This article reports on the…

American Influence on Okinawan Culture before 1972.

ERIC Educational Resources Information Center

Trafton, Terry

The Ryukyu Islands form a chain stretching from the southernmost point of mainland Japan to the northern tip of Taiwan. The largest and most important of these islands is Okinawa. This paper documents the influence of other nations and cultures upon the Okinawan culture, and focuses upon U.S. cultural influence. In the mid-nineteenth century,…

Enhancing the IT Infrastructure at Saint Philip's Hospital: Point-of-Care Solutions

ERIC Educational Resources Information Center

Naydenova, Iva; White, Bruce

2013-01-01

Healthcare has become a rapidly changing field. With the introduction of value-based purchasing to determine reimbursement of Medicare providers based on the quality of care in addition to outcomes in treatment, the environment is becoming ever more competitive. Saint Philip's Hospital is among the largest non-profit hospitals in the nation…

Trends in shortleaf pine tree improvement

Treesearch

Robert N. Kitchens

1986-01-01

Tree improvement programs of shortleaf pine (Pinus echinata Mill.) have developed over the past 25 years to the point that virtually all demand for planting stock is met with genetically improved trees. About 22,600 acres of improved stock are planted each year. Although shortleaf has the largest geographic range of any southern pine, it is not being promoted in...

Renal denervation: What happened, and why?

PubMed

Shishehbor, Mehdi H; Hammad, Tarek A; Thomas, George

2017-09-01

Despite promising results in initial trials, renal denervation failed to achieve its efficacy end points as a treatment for resistant hypertension in the SYMPLICITY HTN-3 trial, the largest trial of this treatment to date (N Engl J Med 2014; 370:1393-1401). Is renal denervation dead, or will future trials and newer technology revive it? Copyright © 2017 Cleveland Clinic.

Giant impactors - Plausible sizes and populations

NASA Technical Reports Server (NTRS)

Hartmann, William K.; Vail, S. M.

1986-01-01

The largest sizes of planetesimals required to explain spin properties of planets are investigated in the context of the impact-trigger hypothesis of lunar origin. Solar system models with different large impactor sources are constructed and stochastic variations in obliquities and rotation periods resulting from each source are studied. The present study finds it highly plausible that earth was struck by a body of about 0.03-0.12 earth masses with enough energy and angular momentum to dislodge mantle material and form the present earth-moon system.

Ground Deposition of Liquid Droplets Released from a Point Source in the Atmospheric Surface Layer.

NASA Astrophysics Data System (ADS)

Panneton, Bernard

1989-09-01

A series of field experiments is presented in which the ground deposition of liquid droplets, 120 and 150 μm in diameter, released from a point source at 7 meters above the ground level, was measured. A detailed description of the experimental technique is provided, and the results are presented and compared to the predictions of a few models. A new rotating droplet generator is described. Droplets are produced by the forced breakup of capillary liquid jets and droplet coalescence is inhibited by the rotational motion of the spray head. A system for analyzing spray samples has been developed. This is a specialized image analysis system based on an electronic digitizing camera which measures the area and perimeter of stains left by dyed droplets collected on Kromekote^{rm TM } cards. A complete set of meteorological data supports the ground-deposition data. The turbulent air velocities at two levels above the ground and the temperature of the air at one level were measured with one sonic anemometer and a sonic anemometer-thermometer. The vertical heat and momentum fluxes were estimated using the eddy-correlation technique. The two-dimensional deposition patterns are presented in the form of plots of contours of constant density, normalized arcwise distributions and crosswind integrated distributions. The arcwise distributions follow a Gaussian distribution whose standard deviation is evaluated using a modified Pasquill's beta technique. Models of the crosswind integrated deposit from Godson, Csanady, Walker, Bache and Sayer, and Wilson et al are evaluated. The results indicate that the Wilson et al random walk model is adequate for predicting the ground deposition of the 150 μm droplets. In one case, where the ratio of the droplet settling velocity to the mean wind speed was largest, Walker's model proved to be adequate. Otherwise, none of the models were acceptable in light of our experimental data.

Besieged by Trojans: Material Exchange between Tethys and its Coorbital Moons

NASA Astrophysics Data System (ADS)

Nayak, Michael; Rhoden, Alyssa R.; Asphaug, Erik

2016-10-01

Two small Trojan moons are coorbital with the Saturnian moon Tethys: Calypso (20-km diameter) resides in the trailing L5 Lagrangian point of Tethys' orbit around Saturn, while Telesto (25-km diameter) occupies the leading L4 Lagrangian point. Due to their fixed location with respect to Tethys, consistent material transfer to Tethys occurs whenever there is a primary impact on either of the Trojan moons. Here we investigate this material exchange, and its implications for the cratering history of Tethys. Multiple craters in excess of 1-km in diameter are seen on both Trojan moons [1]. We model the evolution of ejecta escaping from the largest five and seven craters on Calypso and Telesto respectively. The Maxwell Z-model [2] is used, with an implicit gravity-regime cratering assumption, to approximate outbound ejecta velocity distributions. The smallest craters considered on Calypso and Telesto are 1.35 and 1.9 km in diameter respectively; these impacts would have generated a significant amount of sesquinary ejecta [3] in orbits coorbital to that of Tethys. We model the evolution of these sesquinary ejecta in the Saturnian gravity system across 100 years and track their impact locations [e.g. 4]. Our results show that a large fraction of sesquinary ejecta created by primary impacts to either Trojan is likely to impact Tethys; the coorbital nature of the source bodies results in a significant fraction of this ejecta being incident at low impact velocities and low (oblique) impact angles. We present results of ongoing work to convolve these results with observed crater populations and morphologies on Tethys. The persistence of sesquinary impactors inbound to Tethys suggests that such impacts are a relatively frequent process. Additional sources of impactor material, such as from material excavated by primary impacts to Tethys and later reaccreted, will also be discussed. [1] Thomas et al., 2013, Icarus [2] Melosh, 1989, Oxford Univ. Press [3] Zahnle et al., 2008, Icarus [4] Nayak and Asphaug, 2016, Nature Communications.

Beautiful forms and compositions are not made by chance: Exploring the efficacy of portable X-ray fluorescence to sort and source English lead glazed ceramics

NASA Astrophysics Data System (ADS)

Sarich, Steven J.

Advances in portable X-ray fluorescence (pXRF) technology have made it a viable option for the non-destructive exploration of the underlying chemical composition of ceramic artifacts for the purposes of classification. However, because the literature regarding the use of this instrument on historic artifacts is limited, it is necessary to begin with a broad scale exploratory assessment that might act as a jumping off point for future studies on this topic. Toward that end, this research uses a collection of British and Continental European ceramics ranging from 1650-1920, owned and curated by the Chipstone Foundation in Fox Point, WI, to explore the efficacy of using pXRF to sort and source those materials. The chemical patterns in the data are tested against the known provenance of these artifacts which has been pre-determined by ceramic experts and material culture analysts. Of the 102 samples that have been tested, primary focus is given to items crafted in London and Staffordshire which account for the largest portion of artifacts in the dataset. Principle component analysis is used to better understand the underlying structure of the entire dataset to ultimately reduce the number of chemical variables to those that best distinguish each group. Using those particular chemical variables, a separate dataset of London and Staffordshire mean intensity readings is subjected to factor analysis which resulted in two components being identified. The calculated factor scores are incorporated into a binary logistic regression model to determine if the samples can be correctly sorted into their pre-established provenance categories. A second model that incorporates the year of production is also presented which shows an improved ability to classify those samples. These results are ultimately situated within the historic context of the pottery making industry in England which was highly influenced by the Industrial Revolution and developments in ceramic technology.

Analysis of point source size on measurement accuracy of lateral point-spread function of confocal Raman microscopy

NASA Astrophysics Data System (ADS)

Fu, Shihang; Zhang, Li; Hu, Yao; Ding, Xiang

2018-01-01

Confocal Raman Microscopy (CRM) has matured to become one of the most powerful instruments in analytical science because of its molecular sensitivity and high spatial resolution. Compared with conventional Raman Microscopy, CRM can perform three dimensions mapping of tiny samples and has the advantage of high spatial resolution thanking to the unique pinhole. With the wide application of the instrument, there is a growing requirement for the evaluation of the imaging performance of the system. Point-spread function (PSF) is an important approach to the evaluation of imaging capability of an optical instrument. Among a variety of measurement methods of PSF, the point source method has been widely used because it is easy to operate and the measurement results are approximate to the true PSF. In the point source method, the point source size has a significant impact on the final measurement accuracy. In this paper, the influence of the point source sizes on the measurement accuracy of PSF is analyzed and verified experimentally. A theoretical model of the lateral PSF for CRM is established and the effect of point source size on full-width at half maximum of lateral PSF is simulated. For long-term preservation and measurement convenience, PSF measurement phantom using polydimethylsiloxane resin, doped with different sizes of polystyrene microspheres is designed. The PSF of CRM with different sizes of microspheres are measured and the results are compared with the simulation results. The results provide a guide for measuring the PSF of the CRM.

Area Source Emission Measurements Using EPA OTM 10

EPA Science Inventory

Measurement of air pollutant emissions from area and non-point sources is an emerging environmental concern. Due to the spatial extent and non-homogenous nature of these sources, assessment of fugitive emissions using point sampling techniques can be difficult. To help address th...

BACTERIA SOURCE TRACKING AND HOST SPECIES SPECIFICITY ANALYSIS

EPA Science Inventory

Point and non-point pollution sources of fecal pollution on a watershed adversely impact the quality of drinking source waters and recreational waters. States are required to develop total maximum daily loads (TMDLs) and devise best management practices (BMPs) to reduce the pollu...

Global source attribution of sulfate concentration and direct and indirect radiative forcing

NASA Astrophysics Data System (ADS)

Yang, Yang; Wang, Hailong; Smith, Steven J.; Easter, Richard; Ma, Po-Lun; Qian, Yun; Yu, Hongbin; Li, Can; Rasch, Philip J.

2017-07-01

The global source-receptor relationships of sulfate concentrations, and direct and indirect radiative forcing (DRF and IRF) from 16 regions/sectors for years 2010-2014 are examined in this study through utilizing a sulfur source-tagging capability implemented in the Community Earth System Model (CESM) with winds nudged to reanalysis data. Sulfate concentrations are mostly contributed by local emissions in regions with high emissions, while over regions with relatively low SO2 emissions, the near-surface sulfate concentrations are primarily attributed to non-local sources from long-range transport. Regional source efficiencies of sulfate concentrations are higher over regions with dry atmospheric conditions and less export, suggesting that lifetime of aerosols, together with regional export, is important in determining regional air quality. The simulated global total sulfate DRF is -0.42 W m-2, with -0.31 W m-2 contributed by anthropogenic sulfate and -0.11 W m-2 contributed by natural sulfate, relative to a state with no sulfur emissions. In the Southern Hemisphere tropics, dimethyl sulfide (DMS) contributes 17-84 % to the total DRF. East Asia has the largest contribution of 20-30 % over the Northern Hemisphere mid- and high latitudes. A 20 % perturbation of sulfate and its precursor emissions gives a sulfate incremental IRF of -0.44 W m-2. DMS has the largest contribution, explaining -0.23 W m-2 of the global sulfate incremental IRF. Incremental IRF over regions in the Southern Hemisphere with low background aerosols is more sensitive to emission perturbation than that over the polluted Northern Hemisphere.

[Bibliometric analysis of literature regarding integrated schistosomiasis control strategy with emphasis on infectious source control].

PubMed

Qian, Yi-Li; Wang, Wei; Hong, Qing-Biao; Liang, You-Sheng

2014-12-01

To evaluate the outcomes of implementation of integrated schistosomiasis control strategy with emphasis on infectious source control using a bibliometric method. The literature pertaining to integrated schistosomiasis control strategy with emphasis on infectious source control was retrieved from CNKI, Wanfangdata, VIP, PubMed, Web of Science, BIOSIS and Google Scholar, and a bibliometric analysis of literature captured was performed. During the period from January 1, 2004 through September 30, 2014, a total of 94 publications regarding integrated schistosomiasis control strategy with emphasis on infectious source control were captured, including 78 Chinese articles (82.98%) and 16 English papers (17.02%). The Chinese literature was published in 21 national journals, and Chinese Journal of Schistosomiasis Control had the largest number of publications, consisting of 37.23% of total publications; 16 English papers were published in 12 international journals, and PLoS Neglected Tropical Diseases had the largest number of publications (3 publications). There were 37 affiliations publishing these 94 articles, and National Institute of Parasitic Diseases, Chinese Center for Disease Control and Prevention (16 publications), Anhui Institute of Schistosomiasis Control (12 publications) and Hunan Institute of Schistosomiasis Control (9 publications) ranked top three affiliations in number of publications. A total of 157 persons were co-authored in these 94 publications, and Wang, Zhou and Zhang ranked top 3 authors in number of publications. The integrated schistosomiasis control strategy with emphasis on infectious source control has been widely implemented in China, and the achievements obtained from the implementation of this strategy should be summarized and transmitted internationally.

Modeling the contribution of point sources and non-point sources to Thachin River water pollution.

PubMed

Schaffner, Monika; Bader, Hans-Peter; Scheidegger, Ruth

2009-08-15

Major rivers in developing and emerging countries suffer increasingly of severe degradation of water quality. The current study uses a mathematical Material Flow Analysis (MMFA) as a complementary approach to address the degradation of river water quality due to nutrient pollution in the Thachin River Basin in Central Thailand. This paper gives an overview of the origins and flow paths of the various point- and non-point pollution sources in the Thachin River Basin (in terms of nitrogen and phosphorus) and quantifies their relative importance within the system. The key parameters influencing the main nutrient flows are determined and possible mitigation measures discussed. The results show that aquaculture (as a point source) and rice farming (as a non-point source) are the key nutrient sources in the Thachin River Basin. Other point sources such as pig farms, households and industries, which were previously cited as the most relevant pollution sources in terms of organic pollution, play less significant roles in comparison. This order of importance shifts when considering the model results for the provincial level. Crosschecks with secondary data and field studies confirm the plausibility of our simulations. Specific nutrient loads for the pollution sources are derived; these can be used for a first broad quantification of nutrient pollution in comparable river basins. Based on an identification of the sensitive model parameters, possible mitigation scenarios are determined and their potential to reduce the nutrient load evaluated. A comparison of simulated nutrient loads with measured nutrient concentrations shows that nutrient retention in the river system may be significant. Sedimentation in the slow flowing surface water network as well as nitrogen emission to the air from the warm oxygen deficient waters are certainly partly responsible, but also wetlands along the river banks could play an important role as nutrient sinks.